Residues leaching from 'Factory of barren ores'

International Nuclear Information System (INIS)

Rakhmatov, N.; Khakimov, N.; Nazarov, Kh.M.; Barotov, A.M.

2012-01-01

The objective of the present work is safe management of residues from Factory of Barren Ores, their reprocessing, expenditures reduction for remediation of Istiklol city former uranium tailings. For this purpose, some experiences were adopted - Factory of Barren Ores tailing use for filling up the open pit where water with uranium content 3-5 mg/l is located. Factory of Barren Ores waste are passed through heap leaching and have some amount of uranium salts dissolved in water. Thus, we propose to dissolve uranium from Factory of Barren Ores wastes with uranium bearing water flowing out from gallery and filling up the open-pit by radioactive wastes. In so doing, uranium content flowing out from gallery will increase twice, and further, passing them through apricot's shell, as a sorbent, we will clean the water against radionuclides. Residue samples with uranium content 0,015% from Factory of Barren Ores and uranium bearing waters from gallery 1 with uranium content 0,0025 g/l were used for laboratory tests. After which, a slurry was prepared by means of residue mixing with water in ratio of solid and liquid phases (S:L) - 1:2 and 9,7 ml of sulfuric acid (Ρ=1,82) was added which corresponds consumption by H 2 SO 4 176,54 kg/t. For the first test, leaching was carried out during 4 hours at ph=1,6 at room temperature. For the second test, leaching was carried out at 60 d eg C a nd ph=1,6 during 4 hours. Slurry heating and mixing was carried out by means of magnetic mixer. The basic residue leaching indicators are provided in this article.

Quinolone-based IMPDH inhibitors: introduction of basic residues on ring D and SAR of the corresponding mono, di and benzofused analogues.

Science.gov (United States)

Dhar, T G Murali; Watterson, Scott H; Chen, Ping; Shen, Zhongqi; Gu, Henry H; Norris, Derek; Carlsen, Marianne; Haslow, Kristin D; Pitts, William J; Guo, Junqing; Chorba, John; Fleener, Catherine A; Rouleau, Katherine A; Townsend, Robert; Hollenbaugh, Diane; Iwanowicz, Edwin J

2003-02-10

The synthesis and the structure-activity relationships (SAR) of analogues derived from the introduction of basic residues on ring D of quinolone-based inhibitors of IMPDH are described. This led to the identification of compound 27 as a potent inhibitor of IMPDH with significantly improved aqueous solubility over the lead compound 1.

Nonsensing residues in S3-S4 linker's C terminus affect the voltage sensor set point in K+ channels.

Science.gov (United States)

Carvalho-de-Souza, Joao L; Bezanilla, Francisco

2018-02-05

Voltage sensitivity in ion channels is a function of highly conserved arginine residues in their voltage-sensing domains (VSDs), but this conservation does not explain the diversity in voltage dependence among different K + channels. Here we study the non-voltage-sensing residues 353 to 361 in Shaker K + channels and find that residues 358 and 361 strongly modulate the voltage dependence of the channel. We mutate these two residues into all possible remaining amino acids (AAs) and obtain Q-V and G-V curves. We introduced the nonconducting W434F mutation to record sensing currents in all mutants except L361R, which requires K + depletion because it is affected by W434F. By fitting Q-Vs with a sequential three-state model for two voltage dependence-related parameters ( V 0 , the voltage-dependent transition from the resting to intermediate state and V 1 , from the latter to the active state) and G-Vs with a two-state model for the voltage dependence of the pore domain parameter ( V 1/2 ), Spearman's coefficients denoting variable relationships with hydrophobicity, available area, length, width, and volume of the AAs in 358 and 361 positions could be calculated. We find that mutations in residue 358 shift Q-Vs and G-Vs along the voltage axis by affecting V 0 , V 1 , and V 1/2 according to the hydrophobicity of the AA. Mutations in residue 361 also shift both curves, but V 0 is affected by the hydrophobicity of the AA in position 361, whereas V 1 and V 1/2 are affected by size-related AA indices. Small-to-tiny AAs have opposite effects on V 1 and V 1/2 in position 358 compared with 361. We hypothesize possible coordination points in the protein that residues 358 and 361 would temporarily and differently interact with in an intermediate state of VSD activation. Our data contribute to the accumulating knowledge of voltage-dependent ion channel activation by adding functional information about the effects of so-called non-voltage-sensing residues on VSD dynamics. © 2018

Moisture removal of paddy by agricultural residues: basic physical parameters and drying kinetics modeling

Directory of Open Access Journals (Sweden)

Saniso, E.

2007-05-01

Full Text Available The objectives of this research were to study basic physical parameters of three agricultural residues that could be used for prediction of paddy drying kinetics using desiccants, to investigate a suitable methodfor moisture reduction of fresh paddy using 3 absorbents, and to modify the drying model of Inoue et al. for determining the evolution of moisture transfer during the drying period. Rice husk, sago palm rachis andcoconut husk were used as moisture desiccants in these experiments. From the results, it was concluded that the apparent density of all adsorbents was a linear function of moisture content whilst an equilibriummoisture content equation following Hendersonís model gave the best fit to the experimental results. From studying the relationship between moisture ratio and drying time under the condition of drying temperaturesof 30, 50 and 70oC, air flow rate of 1.6 m/s and initial moisture content of absorbents of 15, 20 and 27% dry-basis, it was shown that the moisture ratio decreased when drying time increased. In addition, thethin-layer desiccant drying equation following of the Page model can appropriately explain the evolution of moisture content of paddy over the drying time. The diffusion coefficient of all absorbents, which was in therange of 1x10-8 to 6x10-8 m2/h, was relatively dependent on drying temperature and inversely related to drying time. The diffusivity of coconut husk had the highest value compared to the other absorbents.The simulating modified mathematical model to determine drying kinetics of paddy using absorption technique and the simulated results had good relation to the experimental results for all adsorbents.

Higher spin gauge theory on fuzzy \\boldsymbol {S^4_N}

Science.gov (United States)

Sperling, Marcus; Steinacker, Harold C.

2018-02-01

We examine in detail the higher spin fields which arise on the basic fuzzy sphere S^4N in the semi-classical limit. The space of functions can be identified with functions on classical S 4 taking values in a higher spin algebra associated to \

Restoring CERN’s basic fabric

CERN Document Server

2009-01-01

Many of you will have noticed work going on around the CERN site: old trees are being removed, plumbing is being installed and scaffolding is going up around buildings. This is all part of a coordinated approach to consolidating CERN’s basic infrastructure: work that has been put on hold for many years while the Lab’s top priority was completing the LHC. Now that the LHC is built, it’s time to turn our attention to CERN’s buildings and open spaces. CERN covers a vast area and has many buildings, some dating back to the 1950s. For several years, building maintenance has been carried out on an as-necessary basis, with little attention being paid to preventative measures. As a result, there is much to be done, and it will take time to achieve. For our open spaces, it’s the same story. At CERN, we enjoy a very green working environment, but our trees are ageing and in some cases in danger of falling. The priority for 2009 is ...

U.S. Geological Survey experience with the residual absolutes method

Directory of Open Access Journals (Sweden)

E. W. Worthington

2017-10-01

Full Text Available The U.S. Geological Survey (USGS Geomagnetism Program has developed and tested the residual method of absolutes, with the assistance of the Danish Technical University's (DTU Geomagnetism Program. Three years of testing were performed at College Magnetic Observatory (CMO, Fairbanks, Alaska, to compare the residual method with the null method. Results show that the two methods compare very well with each other and both sets of baseline data were used to process the 2015 definitive data. The residual method will be implemented at the other USGS high-latitude geomagnetic observatories in the summer of 2017 and 2018.

Magnetic charges in the AdS(4) superalgebra osp(4 vertical bar 2)

NARCIS (Netherlands)

Dibitetto, Giuseppe; Klemm, Dietmar

2010-01-01

We discuss the issue of how to include magnetic charges in the AdS(4) superalgebra osp(4 vertical bar 2). It is shown that the usual way of introducing a pseudoscalar central charge on the right hand side of the basic anticommutator does not work, because this breaks SO(2, 3) covariance. We propose

Cloning and characterization of an 11S legumin, Car i 4, a major allergen in pecan.

Science.gov (United States)

Sharma, Girdhari M; Irsigler, Andre; Dhanarajan, Pushparani; Ayuso, Rosalia; Bardina, Luda; Sampson, Hugh A; Roux, Kenneth H; Sathe, Shridhar K

2011-09-14

Among tree nut allergens, pecan allergens remain to be identified and characterized. The objective was to demonstrate the IgE-binding ability of pecan 11S legumin and characterize its sequential IgE-binding epitopes. The 11S legumin gene was amplified from a pecan cDNA library and expressed as a fusion protein in Escherichia coli. The native 11S legumin in pecan extract was identified by mass spectrometry/mass spectrometry (MS/MS). Sequential epitopes were determined by probing the overlapping peptides with three serum pools prepared from different patients' sera. A three-dimensional model was generated using almond legumin as a template and compared with known sequential epitopes on other allergenic tree nut homologues. Of 28 patients tested by dot blot, 16 (57%) bound to 11S legumin, designated Car i 4. MS/MS sequencing of native 11S legumin identified 33 kDa acidic and 20-22 kDa basic subunits. Both pecan and walnut seed protein extracts inhibited IgE binding to recombinant Car i 4, suggesting cross-reactivity with Jug r 4. Sequential epitope mapping results of Car i 4 revealed weak, moderate, and strong reactivity of serum pools against 10, 5, and 4 peptides, respectively. Seven peptides were recognized by all three serum pools, of which two were strongly reactive. The strongly reactive peptides were located in three discrete regions of the Car i 4 acidic subunit sequence (residues 118-132, 208-219, and 238-249). Homology modeling of Car i 4 revealed significant overlapping regions shared in common with other tree nut legumins.

Essential histidyl residues at the active site(s) of sucrose-phosphate synthase from Prosopis juliflora.

Science.gov (United States)

Sinha, A K; Pathre, U V; Sane, P V

1998-11-10

Chemical modification of sucrose-phosphate synthase (EC 2.4.1.14) from Prosopis juliflora by diethyl pyrocarbonate (DEP) and photo-oxidation in the presence of rose bengal (RB) which modify the histidyl residues of the protein resulted in the inactivation of the enzyme activity. This inactivation was dependent on the concentration of the modifying reagent and the time of incubation and followed pseudo-first order kinetics. For both the reagents, the inactivation was maximum at pH 7.5, which is consistent with the involvement and presence of histidine residues at the active site of the enzyme. Substrates, UDPG and F6P protected the enzyme against the inactivation by the modifying reagents suggesting that the histidine residues may be involved in the binding of these substrates and are essential for the catalytic activity. Specificity of DEP was indicated by an increase in absorbance at 240 nm along with concomitant inactivation of the enzyme and reactivation of the modified enzyme by hydroxylamine. These results strongly suggest the presence of histidine residue(s) at or near the active site of the enzyme.

Samsung Galaxy S4 for dummies

CERN Document Server

Hughes, Bill

2013-01-01

Explore a world of possibilities with your Samsung Galaxy S 4 smartphone Everything's more exciting when you've got the Galaxy in your hand. Let For Dummies be your guide to getting the most out of your Galaxy S 4. You'll cruise through the smartphone basics and set up process before moving on to the fun stuff like staying in touch with e-mail and texting, surfing the web, navigating with maps, shooting and sharing photos and video, watching movies, listening to music, and so much more. Whether you're entering the smartphone world for the first time or just moving up to

Metabolism and Residues of 2,4-Dichlorophenoxyacetic Acid in DAS-40278-9 Maize (Zea mays) Transformed with Aryloxyalkanoate Dioxygenase-1 Gene.

Science.gov (United States)

Zhou, Xiao; Rotondaro, Sandra L; Ma, Mingming; Rosser, Steve W; Olberding, Ed L; Wendelburg, Brian M; Adelfinskaya, Yelena A; Balcer, Jesse L; Blewett, T Craig; Clements, Bruce

2016-10-12

DAS-40278-9 maize, which is developed by Dow AgroSciences, has been genetically modified to express the aryloxyalkanoate dioxygenase-1 (AAD-1) protein and is tolerant to phenoxy auxin herbicides, such as 2,4-dichlorophenoxyacetic acid (2,4-D). To understand the metabolic route and residue distribution of 2,4-D in DAS-40278-9 maize, a metabolism study was conducted with 14 C-radiolabeled 2,4-D applied at the maximum seasonal rate. Plants were grown in boxes outdoors. Forage and mature grain, cobs, and stover were collected for analysis. The metabolism study showed that 2,4-D was metabolized to 2,4-dichlorophenol (2,4-DCP), which was then rapidly conjugated with glucose. Field-scale residue studies with 2,4-D applied at the maximum seasonal rate were conducted at 25 sites in the U.S. and Canada to measure the residues of 2,4-D and free and conjugated 2,4-DCP in mature forage, grain, and stover. Residues of 2,4-D were not detectable in the majority of the grain samples and averaged <1.0 and <1.5 μg/g in forage and stover, respectively. Free plus conjugated 2,4-DCP was not observed in grain and averaged <1.0 μg/g in forage and stover.

40 CFR 180.1281 - S-Abscisic Acid, (S)-5-(1-hydroxy-2,6,6-trimethyl-4-oxo-1-cyclohex-2-enyl)-3-methyl-penta-(2Z,4E...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false S-Abscisic Acid, (S)-5-(1-hydroxy-2,6... Exemptions From Tolerances § 180.1281 S-Abscisic Acid, (S)-5-(1-hydroxy-2,6,6-trimethyl-4-oxo-1-cyclohex-2... from the requirement of a tolerance is established for residues of S-Abscisic Acid in or on all food...

The S4-S5 linker acts as a signal integrator for HERG K+ channel activation and deactivation gating.

Directory of Open Access Journals (Sweden)

Chai Ann Ng

Full Text Available Human ether-à-go-go-related gene (hERG K(+ channels have unusual gating kinetics. Characterised by slow activation/deactivation but rapid inactivation/recovery from inactivation, the unique gating kinetics underlie the central role hERG channels play in cardiac repolarisation. The slow activation and deactivation kinetics are regulated in part by the S4-S5 linker, which couples movement of the voltage sensor domain to opening of the activation gate at the distal end of the inner helix of the pore domain. It has also been suggested that cytosolic domains may interact with the S4-S5 linker to regulate activation and deactivation kinetics. Here, we show that the solution structure of a peptide corresponding to the S4-S5 linker of hERG contains an amphipathic helix. The effects of mutations at the majority of residues in the S4-S5 linker of hERG were consistent with the previously identified role in coupling voltage sensor movement to the activation gate. However, mutations to Ser543, Tyr545, Gly546 and Ala548 had more complex phenotypes indicating that these residues are involved in additional interactions. We propose a model in which the S4-S5 linker, in addition to coupling VSD movement to the activation gate, also contributes to interactions that stabilise the closed state and a separate set of interactions that stabilise the open state. The S4-S5 linker therefore acts as a signal integrator and plays a crucial role in the slow deactivation kinetics of the channel.

Investigation of Diesel’s Residual Noise on Predictive Vehicles Noise Cancelling using LMS Adaptive Algorithm

Science.gov (United States)

Arttini Dwi Prasetyowati, Sri; Susanto, Adhi; Widihastuti, Ida

2017-04-01

Every noise problems require different solution. In this research, the noise that must be cancelled comes from roadway. Least Mean Square (LMS) adaptive is one of the algorithm that can be used to cancel that noise. Residual noise always appears and could not be erased completely. This research aims to know the characteristic of residual noise from vehicle’s noise and analysis so that it is no longer appearing as a problem. LMS algorithm was used to predict the vehicle’s noise and minimize the error. The distribution of the residual noise could be observed to determine the specificity of the residual noise. The statistic of the residual noise close to normal distribution with = 0,0435, = 1,13 and the autocorrelation of the residual noise forming impulse. As a conclusion the residual noise is insignificant.

Non-basic amino acids in the ROMK1 channels via an appropriate distance modulate PIP2 regulated pHi-gating.

Science.gov (United States)

Lee, Chien-Hsing; Huang, Po-Tsang; Liou, Horng-Huei; Lin, Mei-Ying; Lou, Kuo-Long; Chen, Chung-Yi

2016-04-22

The ROMK1 (Kir1.1) channel activity is predominantly regulated by intracellular pH (pHi) and phosphatidylinositol 4,5-bisphosphate (PIP2). Although several residues were reported to be involved in the regulation of pHi associated with PIP2 interaction, the detailed molecular mechanism remains unclear. We perform experiments in ROMK1 pHi-gating with electrophysiology combined with mutational and structural analysis. In the present study, non basic residues of C-terminal region (S219, N215, I192, L216 and L220) in ROMK1 channels have been found to mediate channel-PIP2 interaction and pHi gating. Further, our structural results show these residues with an appropriate distance to interact with membrane PIP2. Meanwhile, a cluster of basic residues (R188, R217 and K218), which was previously discovered regarding the interaction with PIP2, exists in this appropriate distance to discriminate the regulation of channel-PIP2 interaction and pHi-gating. This appropriate distance can be observed with high conservation in the Kir channel family. Our results provide insight that an appropriate distance cooperates with the electrostatics interaction of channel-PIP2 to regulate pHi-gating. Copyright © 2016 Elsevier Inc. All rights reserved.

Residual Inequity: Assessing the Unintended Consequences of New York City’s Clean Heat Transition

Science.gov (United States)

Carrión, Daniel; Lee, W. Victoria; Hernández, Diana

2018-01-01

Energy policies and public health are intimately intertwined. In New York City, a series of policies, known as the Clean Heat Program (CHP), were designed to reduce air pollution by banning residual diesel fuel oils, #6 in 2015 and #4 by 2030. This measure is expected to yield environmental and public health benefits over time. While there is near-universal compliance with the #6 ban, a substantial number of buildings still use #4. In this paper, geographic analysis and qualitative interviews with stakeholders were used to interrogate the CHP’s policy implementation in Northern Manhattan and the Bronx. A total of 1724 (53%) of all residential residual fuel burning buildings are located in this region. Stakeholders reflected mostly on the need for the program, and overall reactions to its execution. Major findings include that government partnerships with non-governmental organizations were effectively employed. However, weaknesses with the policy were also identified, including missed opportunities for more rapid transitions away from residual fuels, unsuccessful outreach efforts, cost-prohibitive conversion opportunities, and (the perception of) a volatile energy market for clean fuels. Ultimately, this analysis serves as a case study of a unique and innovative urban policy initiative to improve air quality and, consequently, public health. PMID:29324717

Residual Inequity: Assessing the Unintended Consequences of New York City’s Clean Heat Transition

Directory of Open Access Journals (Sweden)

Daniel Carrión

2018-01-01

Full Text Available Energy policies and public health are intimately intertwined. In New York City, a series of policies, known as the Clean Heat Program (CHP, were designed to reduce air pollution by banning residual diesel fuel oils, #6 in 2015 and #4 by 2030. This measure is expected to yield environmental and public health benefits over time. While there is near-universal compliance with the #6 ban, a substantial number of buildings still use #4. In this paper, geographic analysis and qualitative interviews with stakeholders were used to interrogate the CHP’s policy implementation in Northern Manhattan and the Bronx. A total of 1724 (53% of all residential residual fuel burning buildings are located in this region. Stakeholders reflected mostly on the need for the program, and overall reactions to its execution. Major findings include that government partnerships with non-governmental organizations were effectively employed. However, weaknesses with the policy were also identified, including missed opportunities for more rapid transitions away from residual fuels, unsuccessful outreach efforts, cost-prohibitive conversion opportunities, and (the perception of a volatile energy market for clean fuels. Ultimately, this analysis serves as a case study of a unique and innovative urban policy initiative to improve air quality and, consequently, public health.

Physicochemical investigation of reactions of some basic cadmium salts formation in aqueous solutions

International Nuclear Information System (INIS)

Gyunner, Eh.A.; Mel'nichenko, L.M.; Yakhkind, N.D.; Vel'mozhnyj, I.S.; Pevzner, N.S.

1980-01-01

By the methods of physicochemical analysis (the method of residual concentrations, refractometry), the composition of slightly soluble products of interaction in the five systems of the Cd(CHsub(3)COO)sub(2)-Msub(z)X-NaOH-Hsub(2)O type (Msub(z)X - NaF, KClO 3 , KBrO 3 , NaHCOO, Na 2 S 2 O 3 ) has been detemined. It has been established that in systems with NaF, NaHCOO and Na 2 S 2 O 3 , cadmium hydroxide formation is preceded by deposition of the basic salts Cd(OH)F, Cd(OH)HCOO, and Cd 4 (OH) 6 S 2 O 3 . In systems with KClO 3 and KBrO 3 the only interaction slightly soluble product is Cd(OH) 2

Characterization of Human and Murine T-Cell Immunoglobulin Mucin Domain 4 (TIM-4) IgV Domain Residues Critical for Ebola Virus Entry.

Science.gov (United States)

Rhein, Bethany A; Brouillette, Rachel B; Schaack, Grace A; Chiorini, John A; Maury, Wendy

2016-07-01

Phosphatidylserine (PtdSer) receptors that are responsible for the clearance of dying cells have recently been found to mediate enveloped virus entry. Ebola virus (EBOV), a member of the Filoviridae family of viruses, utilizes PtdSer receptors for entry into target cells. The PtdSer receptors human and murine T-cell immunoglobulin mucin (TIM) domain proteins TIM-1 and TIM-4 mediate filovirus entry by binding to PtdSer on the virion surface via a conserved PtdSer binding pocket within the amino-terminal IgV domain. While the residues within the TIM-1 IgV domain that are important for EBOV entry are characterized, the molecular details of virion-TIM-4 interactions have yet to be investigated. As sequences and structural alignments of the TIM proteins suggest distinct differences in the TIM-1 and TIM-4 IgV domain structures, we sought to characterize TIM-4 IgV domain residues required for EBOV entry. Using vesicular stomatitis virus pseudovirions bearing EBOV glycoprotein (EBOV GP/VSVΔG), we evaluated virus binding and entry into cells expressing TIM-4 molecules mutated within the IgV domain, allowing us to identify residues important for entry. Similar to TIM-1, residues in the PtdSer binding pocket of murine and human TIM-4 (mTIM-4 and hTIM-4) were found to be important for EBOV entry. However, additional TIM-4-specific residues were also found to impact EBOV entry, with a total of 8 mTIM-4 and 14 hTIM-4 IgV domain residues being critical for virion binding and internalization. Together, these findings provide a greater understanding of the interaction of TIM-4 with EBOV virions. With more than 28,000 cases and over 11,000 deaths during the largest and most recent Ebola virus (EBOV) outbreak, there has been increased emphasis on the development of therapeutics against filoviruses. Many therapies under investigation target EBOV cell entry. T-cell immunoglobulin mucin (TIM) domain proteins are cell surface factors important for the entry of many enveloped viruses

Hanford Tank 241-S-112 Residual Waste Composition and Leach Test Data

Energy Technology Data Exchange (ETDEWEB)

Cantrell, Kirk J.; Krupka, Kenneth M.; Geiszler, Keith N.; Lindberg, Michael J.; Arey, Bruce W.; Schaef, Herbert T.

2008-08-29

This report presents the results of laboratory characterization and testing of two samples (designated 20406 and 20407) of residual waste collected from tank S-112 after final waste retrieval. These studies were completed to characterize the residual waste and assess the leachability of contami¬nants from the solids. This is the first report from this PNNL project to describe the composition and leach test data for residual waste from a salt cake tank. All previous PNNL reports (Cantrell et al. 2008; Deutsch et al. 2006, 2007a, 2007b, 2007c) describing contaminant release models, and characterization and testing results for residual waste in single-shell tanks were based on samples from sludge tanks.

The effects of Pantoea sp. strain Y4-4 on alfalfa in the remediation of heavy-metal-contaminated soil, and auxiliary impacts of plant residues on the remediation of saline-alkali soils.

Science.gov (United States)

Li, Shuhuan; Wang, Jie; Gao, Nanxiong; Liu, Lizhu; Chen, Yahua

2017-04-01

The plant-growth-promoting rhizobacterium (PGPR) Y4-4 was isolated from plant rhizosphere soil and identified as Pantoea sp. by 16S rRNA sequence analysis. The effects of strain Y4-4 on alfalfa grown in heavy-metals-contaminated soil was investigated using a pot experiment. In a Cu-rich environment, the shoot dry mass and total dry mass of plants inoculated with strain Y4-4 increased by 22.6% and 21%, and Cu accumulation increased by 15%. In a Pb-Zn-rich environment, the shoot dry mass and total dry mass of plants inoculated with strain Y4-4 increased by 23.4% and 22%, and Zn accumulation increased by 30.3%. In addition, the salt tolerance and biomass of wheat seedlings could be improved by applying strain Y4-4 mixed with plant residue as a result of the Cu-rich plant residues providing copper nutrition to wheat. This study offers an efficient PGPR with strong salt tolerance and a safe strategy for the post-treatment of plant residue.

Studies on distribution and residue of sulfur in simulated acid rain in vegetable and soil by using 35S

International Nuclear Information System (INIS)

Wan Zhaoliang; Liu Dayong

1995-01-01

Distribution and residue of sulfur in simulated acid rain in two kinds of vegetables (lettuce and Chinese cabbage) and three types of soils (acid yellow earth, acid and neutral purple soils) were studied by using 35 S tracer method. The results showed that the higher concentration of acid rain was sprayed, the more residue of sulfur in vegetable there would be. The residue of sulfur in vegetable varied with the different physical and chemical properties of soils, the order of sulfur residue in vegetable was: acid purple soil>acid yellow earth>neutral purple soil. In the same soil, the residue of sulfur in lettuce was higher than that in Chinese cabbage, for the same vegetable, the residue of sulfur in leaves were higher than that in stems. The order of sulfur residue in different soils was acid purple soil>acid yellow earth>neutral purple soil. The higher concentration of acid rain was sprayed, the more residue of sulfur in soil surface there would be. The sulfur residue varied with the depth of soil and the pH value of acid rain. With the increase of soil depth, a slight increase of sulfur residue with rain of ph 6 and a slight decrease with rain of pH 4.0 and 2.5 were found

The topogenic function of S4 promotes membrane insertion of the voltage-sensor domain in the KvAP channel.

Science.gov (United States)

Mishima, Eriko; Sato, Yoko; Nanatani, Kei; Hoshi, Naomi; Lee, Jong-Kook; Schiller, Nina; von Heijne, Gunnar; Sakaguchi, Masao; Uozumi, Nobuyuki

2016-12-01

Voltage-dependent K + (K V ) channels control K + permeability in response to shifts in the membrane potential. Voltage sensing in K V channels is mediated by the positively charged transmembrane domain S4. The best-characterized K V channel, KvAP, lacks the distinct hydrophilic region corresponding to the S3-S4 extracellular loop that is found in other K + channels. In the present study, we evaluated the topogenic properties of the transmembrane regions within the voltage-sensing domain in KvAP. S3 had low membrane insertion activity, whereas S4 possessed a unique type-I signal anchor (SA-I) function, which enabled it to insert into the membrane by itself. S4 was also found to function as a stop-transfer signal for retention in the membrane. The length and structural nature of the extracellular S3-S4 loop affected the membrane insertion of S3 and S4, suggesting that S3 membrane insertion was dependent on S4. Replacement of charged residues within the transmembrane regions with residues of opposite charge revealed that Asp 72 in S2 and Glu 93 in S3 contributed to membrane insertion of S3 and S4, and increased the stability of S4 in the membrane. These results indicate that the SA-I function of S4, unique among K + channels studied to date, promotes the insertion of S3 into the membrane, and that the charged residues essential for voltage sensing contribute to the membrane-insertion of the voltage sensor domain in KvAP. © 2016 The Author(s); published by Portland Press Limited on behalf of the Biochemical Society.

Involvement of Histidine Residue His382 in pH Regulation of MCT4 Activity.

Directory of Open Access Journals (Sweden)

Shotaro Sasaki

Full Text Available Monocarboxylate transporter 4 (MCT4 is a pH-dependent bi-directional lactate transporter. Transport of lactate via MCT4 is increased by extracellular acidification. We investigated the critical histidine residue involved in pH regulation of MCT4 function. Transport of lactate via MCT4 was measured by using a Xenopus laevis oocyte expression system. MCT4-mediated lactate transport was inhibited by Zn2+ in a pH physiological condition but not in an acidic condition. The histidine modifier DEPC (diethyl pyrocarbonate reduced MCT4 activity but did not completely inactivate MCT4. After treatment with DEPC, pH regulation of MCT4 function was completely knocked out. Inhibitory effects of DEPC were reversed by hydroxylamine and suppressed in the presence of excess lactate and Zn2+. Therefore, we performed an experiment in which the extracellular histidine residue was replaced with alanine. Consequently, the pH regulation of MCT4-H382A function was also knocked out. Our findings demonstrate that the histidine residue His382 in the extracellular loop of the transporter is essential for pH regulation of MCT4-mediated substrate transport activity.

Basic amino acid residues located in the N-terminal region of BEND3 are essential for its nuclear localization

Energy Technology Data Exchange (ETDEWEB)

Shiheido, Hirokazu, E-mail: shiheido@ak.med.kyoto-u.ac.jp; Shimizu, Jun

2015-02-20

BEN domain-containing protein 3 (BEND3) has recently been reported to function as a heterochromatin-associated protein in transcriptional repression in the nucleus. BEND3 should have nuclear localization signals (NLSs) to localize to the nucleus in light of its molecular weight, which is higher than that allowed to pass through nuclear pore complexes. We here analyzed the subcellular localization of deletion/site-directed mutants of human BEND3 by an immunofluorescence assay in an attempt to identify the amino acids essential for its nuclear localization. We found that three basic amino acid residues located in the N-terminal region of BEND3 (BEND3{sub 56–58}, KRK) are essential, suggesting that these residues play a role as a functional NLS. These results provide valuable information for progressing research on BEND3. - Highlights: • BEND3 localizes to the nucleus. • The N-terminal 60 amino acids region of BEND3 contains NLS. • Amino acids located between 56 and 58 of BEND3 (KRK) are part of NLS. • KRK motif is highly conserved among BEND3 homologs.

NMR of proteins (4Fe-4S): structural properties and intramolecular electron transfer; RMN de proteines (4Fe-4S): proprietes structurales et transfert electronique intramoleculaire

Energy Technology Data Exchange (ETDEWEB)

Huber, J G

1996-10-17

NMR started to be applied to Fe-S proteins in the seventies. Its use has recently been enlarged as the problems arising from the paramagnetic polymetallic clusters ware overcome. Applications to [4Fe-4S] are presented herein. The information derived thereof deepens the understanding of the redox properties of these proteins which play a central role in the metabolism of bacterial cells. The secondary structure elements and the overall folding of Chromatium vinosum ferredoxin (Cv Fd) in solution have been established by NMR. The unique features of this sequence have been shown to fold as an {alpha} helix at the C-terminus and as a loop between two cysteines ligand of one cluster: these two parts localize in close proximity from one another. The interaction between nuclear and electronic spins is a source of additional structural information for (4Fe-AS] proteins. The conformation of the cysteine-ligands, as revealed by the Fe-(S{sub {gamma}}-C{sub {beta}}-H{sub {beta}})Cys dihedral angles, is related to the chemical shifts of the signals associated with the protons of these residues. The longitudinal relaxation times of the protons depend on their distance to the cluster. A quantitative relationship has been established and used to show that the solution structure of the high-potential ferredoxin from Cv differs significantly from the crystal structure around Phe-48. Both parameters (chemical shifts and longitudinal relaxation times) give also insight into the electronic and magnetic properties of the [4Fe-4S] clusters. The rate of intramolecular electron transfer between the two [4FE-4S] clusters of ferredoxins has been measured by NMR. It is far slower in the case of Cv Fd than for shorter ferredoxins. The difference may be associated with changes in the magnetic and/or electronic properties of one cluster. The strong paramagnetism of the [4Fe-4S] clusters, which originally limited the applicability of NMR to proteins containing these cofactors, has been proven

Physicochemical investigation of reactions of some basic cadmium salts formation in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Gyunner, E A; Mel' nichenko, L M; Yakhkind, N D; Vel' mozhnyi, I S; Pevzner, N S [Simferopol' skij Gosudarstvennyj Univ. (Ukrainian SSR)

1980-04-01

By the methods of physicochemical analysis (the method of residual concentrations, refractometry), the composition of slightly soluble products of interaction in the five systems of the Cd(CHsub(3)COO)sub(2)-Msub(z)X-NaOH-Hsub(2)O type (Msub(z)X - NaF, KClO/sub 3/, KBrO/sub 3/, NaHCOO, Na/sub 2/S/sub 2/O/sub 3/) has been detemined. It has been established that in systems with NaF, NaHCOO and Na/sub 2/S/sub 2/O/sub 3/, cadmium hydroxide formation is preceded by deposition of the basic salts Cd(OH)F, Cd(OH)HCOO, and Cd/sub 4/(OH)/sub 6/S/sub 2/O/sub 3/. In systems with KClO/sub 3/ and KBrO/sub 3/ the only interaction slightly soluble product is Cd(OH)/sub 2/.

Mapping residual stresses in PbWO4 crystals using photo-elastic analysis

International Nuclear Information System (INIS)

Lebeau, M.; Gobbi, L.; Majni, G.; Paone, N.; Pietroni, P.; Rinaldi, D.

2005-01-01

Large scintillating crystals are affected by internal stresses induced by the crystal growth temperature gradient remanence. Cutting boules (ingots) into finished crystal shapes allows for a partial tension relaxation but residual stresses remain the main cause of breaking. Quality control of residual stresses is essential in the application of Scintillating Crystals to high-energy physics calorimeters (e.g. CMS ECAL at CERN LHC). In this context the industrial process optimisation towards stress reduction is mandatory. We propose a fast technique for testing samples during the production process in order to evaluate the residual stress distribution after the first phases of mechanical processing. We mapped the stress distribution in PbWO 4 slabs cut from the same production boule. The analysis technique is based on the stress intensity determination using the photo-elastic properties of the samples. The stress distribution is mapped in each sample. The analysis shows that there are regions of high residual tension close to the seed position and at the boule periphery. These results should allow for adapting the industrial process to producing crystals with lower residual stresses

Changes in soil chemical and microbiological properties during 4 years of application of various organic residues.

Science.gov (United States)

Odlare, M; Pell, M; Svensson, K

2008-01-01

A 4-year field trial was established in eastern Sweden to evaluate the effects of organic waste on soil chemical and microbiological variables. A simple crop rotation with barley and oats was treated with either compost from household waste, biogas residue from household waste, anaerobically treated sewage sludge, pig manure, cow manure or mineral fertilizer. All fertilizers were amended in rates corresponding to 100kgNha(-1)year(-1). The effects of the different types of organic waste were evaluated by subjecting soil samples, taken each autumn 4 weeks after harvest, to an extensive set of soil chemical (pH, Org-C, Tot-N, Tot-P, Tot-S, P-AL, P-Olsen, K-AL, and some metals) and microbiological (B-resp, SIR, microSIR active and dormant microorganisms, PDA, microPDA, PAO, Alk-P and N-min) analyses. Results show that compost increased pH, and that compost as well as sewage sludge increased plant available phosphorus; however, the chemical analysis showed few clear trends over the 4 years and few clear relations to plant yield or soil quality. Biogas residues increased substrate induced respiration (SIR) and, compared to the untreated control amendment of biogas residues as well as compost, led to a higher proportion of active microorganisms. In addition, biogas residues increased potential ammonia oxidation rate (PAO), nitrogen mineralization capacity (N-min) as well as the specific growth rate constant of denitrifiers (microPDA). Despite rather large concentrations of heavy metals in some of the waste products, no negative effects could be seen on either chemical or microbiological soil properties. Changes in soil microbial properties appeared to occur more rapidly than most chemical properties. This suggests that soil microbial processes can function as more sensitive indicators of short-term changes in soil properties due to amendment of organic wastes.

Residual mosquito barrier treatments on U.S. military camouflage netting in a southern California desert environment

Science.gov (United States)

Treating perimeters of vegetation with residual insecticides for protection from mosquito vectors has potential for U.S. military force health protection. However, for current U.S. military operations in hot-arid environments with little or no vegetation, residual applications on portable artificial...

Mutagenicity of pan residues and gravy from fried meat.

Science.gov (United States)

Overvik, E; Nilsson, L; Fredholm, L; Levin, O; Nord, C E; Gustafsson, J A

1987-02-01

Lean pork meat was fried with or without the addition of frying-fat at 200 or 250 degrees C. The pan residues were collected by washing the hot pan with boiling water. When producing thickened gravy the water was substituted by a mixture of water and flour, milk and flour or cream and flour. The basic extracts were tested for mutagenicity in Ames' Salmonella test on strain TA98 with the addition of S9 mix. High amounts of mutagenicity were found in all samples. The amounts of mutagenicity in the pan residues were at a comparable level of the amounts found in the meat crusts. Thickening of the gravy caused only small changes in the mutagenicity.

Contribution of S4 segments and S4-S5 linkers to the low-voltage activation properties of T-type CaV3.3 channels.

Directory of Open Access Journals (Sweden)

Ana Laura Sanchez-Sandoval

Full Text Available Voltage-gated calcium channels contain four highly conserved transmembrane helices known as S4 segments that exhibit a positively charged residue every third position, and play the role of voltage sensing. Nonetheless, the activation range between high-voltage (HVA and low-voltage (LVA activated calcium channels is around 30-40 mV apart, despite the high level of amino acid similarity within their S4 segments. To investigate the contribution of S4 voltage sensors for the low-voltage activation characteristics of CaV3.3 channels we constructed chimeras by swapping S4 segments between this LVA channel and the HVA CaV1.2 channel. The substitution of S4 segment of Domain II in CaV3.3 by that of CaV1.2 (chimera IIS4C induced a ~35 mV shift in the voltage-dependence of activation towards positive potentials, showing an I-V curve that almost overlaps with that of CaV1.2 channel. This HVA behavior induced by IIS4C chimera was accompanied by a 2-fold decrease in the voltage-dependence of channel gating. The IVS4 segment had also a strong effect in the voltage sensing of activation, while substitution of segments IS4 and IIIS4 moved the activation curve of CaV3.3 to more negative potentials. Swapping of IIS4 voltage sensor influenced additional properties of this channel such as steady-state inactivation, current decay, and deactivation. Notably, Domain I voltage sensor played a major role in preventing CaV3.3 channels to inactivate from closed states at extreme hyperpolarized potentials. Finally, site-directed mutagenesis in the CaV3.3 channel revealed a partial contribution of the S4-S5 linker of Domain II to LVA behavior, with synergic effects observed in double and triple mutations. These findings indicate that IIS4 and, to a lesser degree IVS4, voltage sensors are crucial in determining the LVA properties of CaV3.3 channels, although the accomplishment of this function involves the participation of other structural elements like S4-S5 linkers.

Contribution of S4 segments and S4-S5 linkers to the low-voltage activation properties of T-type CaV3.3 channels

Science.gov (United States)

Sanchez-Sandoval, Ana Laura; Herrera Carrillo, Zazil; Díaz Velásquez, Clara Estela; Delgadillo, Dulce María; Rivera, Heriberto Manuel

2018-01-01

Voltage-gated calcium channels contain four highly conserved transmembrane helices known as S4 segments that exhibit a positively charged residue every third position, and play the role of voltage sensing. Nonetheless, the activation range between high-voltage (HVA) and low-voltage (LVA) activated calcium channels is around 30–40 mV apart, despite the high level of amino acid similarity within their S4 segments. To investigate the contribution of S4 voltage sensors for the low-voltage activation characteristics of CaV3.3 channels we constructed chimeras by swapping S4 segments between this LVA channel and the HVA CaV1.2 channel. The substitution of S4 segment of Domain II in CaV3.3 by that of CaV1.2 (chimera IIS4C) induced a ~35 mV shift in the voltage-dependence of activation towards positive potentials, showing an I-V curve that almost overlaps with that of CaV1.2 channel. This HVA behavior induced by IIS4C chimera was accompanied by a 2-fold decrease in the voltage-dependence of channel gating. The IVS4 segment had also a strong effect in the voltage sensing of activation, while substitution of segments IS4 and IIIS4 moved the activation curve of CaV3.3 to more negative potentials. Swapping of IIS4 voltage sensor influenced additional properties of this channel such as steady-state inactivation, current decay, and deactivation. Notably, Domain I voltage sensor played a major role in preventing CaV3.3 channels to inactivate from closed states at extreme hyperpolarized potentials. Finally, site-directed mutagenesis in the CaV3.3 channel revealed a partial contribution of the S4-S5 linker of Domain II to LVA behavior, with synergic effects observed in double and triple mutations. These findings indicate that IIS4 and, to a lesser degree IVS4, voltage sensors are crucial in determining the LVA properties of CaV3.3 channels, although the accomplishment of this function involves the participation of other structural elements like S4-S5 linkers. PMID:29474447

Contribution of S4 segments and S4-S5 linkers to the low-voltage activation properties of T-type CaV3.3 channels.

Science.gov (United States)

Sanchez-Sandoval, Ana Laura; Herrera Carrillo, Zazil; Díaz Velásquez, Clara Estela; Delgadillo, Dulce María; Rivera, Heriberto Manuel; Gomora, Juan Carlos

2018-01-01

Voltage-gated calcium channels contain four highly conserved transmembrane helices known as S4 segments that exhibit a positively charged residue every third position, and play the role of voltage sensing. Nonetheless, the activation range between high-voltage (HVA) and low-voltage (LVA) activated calcium channels is around 30-40 mV apart, despite the high level of amino acid similarity within their S4 segments. To investigate the contribution of S4 voltage sensors for the low-voltage activation characteristics of CaV3.3 channels we constructed chimeras by swapping S4 segments between this LVA channel and the HVA CaV1.2 channel. The substitution of S4 segment of Domain II in CaV3.3 by that of CaV1.2 (chimera IIS4C) induced a ~35 mV shift in the voltage-dependence of activation towards positive potentials, showing an I-V curve that almost overlaps with that of CaV1.2 channel. This HVA behavior induced by IIS4C chimera was accompanied by a 2-fold decrease in the voltage-dependence of channel gating. The IVS4 segment had also a strong effect in the voltage sensing of activation, while substitution of segments IS4 and IIIS4 moved the activation curve of CaV3.3 to more negative potentials. Swapping of IIS4 voltage sensor influenced additional properties of this channel such as steady-state inactivation, current decay, and deactivation. Notably, Domain I voltage sensor played a major role in preventing CaV3.3 channels to inactivate from closed states at extreme hyperpolarized potentials. Finally, site-directed mutagenesis in the CaV3.3 channel revealed a partial contribution of the S4-S5 linker of Domain II to LVA behavior, with synergic effects observed in double and triple mutations. These findings indicate that IIS4 and, to a lesser degree IVS4, voltage sensors are crucial in determining the LVA properties of CaV3.3 channels, although the accomplishment of this function involves the participation of other structural elements like S4-S5 linkers.

Analysis by the reductive-cleavage method of linkage positions in a polysaccharide containing 4-linked D-glucopyranosyluronic residues.

Science.gov (United States)

Vodonik, S A; Gray, G R

1988-04-01

The fate of 4-linked D-glucopyranosyluronic residues under reductive-cleavage conditions was investigated by using the Klebsiella aerogenes type 54 strain A3 capsular polysaccharide. Treatment of the fully methylated polysaccharide with triethylsilane and trimethylsilyl trifluoromethanesulfonate in dichloromethane, followed by in situ acetylation, yielded 1,5-anhydro-2,3,4,6-tetra-O-methyl-D-glucitol, 3,4-di-O-acetyl-1,5-anhydro-2,6-di-O-methyl-D-glucitol, and 3-O-acetyl-1,5-anhydro-2,4-di-O-methyl-L-fucitol, as expected, but the expected product of reductive cleavage of the 4-linked D-glucopyranosyluronic residue, namely, methyl 3-O-acetyl-2,6-anhydro-4,5-di-O-methyl-L-gulonate, was not observed. Instead, methyl 2-O-acetyl-3,6-anhydro-4,5-di-O-methyl-L-gulonate (6) was identified as the sole product of reductive cleavage of the 4-linked D-glucopyranosyluronic residue. That compound 6 arose as a result of rearrangement during reductive cleavage rather than by reductive cleavage of a 5-linked D-glucofuranosyluronic residue, was established by reductive cleavage of the fully methylated polysaccharide following reduction of its ester groups with either lithium aluminum hydride or lithium aluminum deuteride. The products of the latter reductive cleavage were the same as before, except for the absence of 6 and the presence of 4,6-di-O-acetyl-1,5-anhydro-2,3-di-O-methyl-D-glucitol, or its 6,6-dideuterio isomer. Although the reductive-cleavage technique is suitable for the direct analysis of polysaccharides containing 4-linked D-glucopyranosyluronic residues, it does not establish whether the uronic residue is a 4-linked pyranoside or a 5-linked furanoside. The expected product is, however, derived from the 4-linked D-glucopyranosyluronic residue after sequential methylation, reduction of its ester group and reductive cleavage.

Stage 4S neuroblastoma, a disseminated tumor with excellent outcome

International Nuclear Information System (INIS)

Elimam, Najla A.; Atra, Ayad A.; Fayea, Najwa Y.; Al-Asaad, Tareq G.; Khattab, Taha M.; Al-Sulami, Ganadeel A.; Felimban, Sami K.

2006-01-01

To review the clinical features and outcome of all cases of stage 4S neuroblastoma treated at our center. We retrospectively reviewed the files of all patients (n=75) with neuroblastoma treated at King Abdul-Aziz Medical City, Jeddah, Kingdom of Saudi Arabia between 1986 and 2005. We studied the clinical features and outcome of patients with stage 4S neuroblastoma. Six patients (8%) were confirmed to have stage 4S neuroblastoma. Three were boys with a median age at diagnosis of 4.5 months (range 28 days-11 moths). Four patients required no intervention. The remaining 2 patients were treated chemotherapy due to progressive hepatomegaly and respiratory distress. No patient required radiotherapy or surgical intervention. With a median follow up of four years (range 9 months --- 15.5 years), all patients are alive and well. Two patients continue to have a residual abdominal mass, while complete resolution occurred in the others. Stage 4S neuroblastoma is special tumor that carries excellent prognosis. Spontaneous regression may occur and intervention is only required in symptomatic patients. (author)

Roles of s3 site residues of nattokinase on its activity and substrate specificity.

Science.gov (United States)

Wu, Shuming; Feng, Chi; Zhong, Jin; Huan, Liandong

2007-09-01

Nattokinase (Subtilisin NAT, NK) is a bacterial serine protease with high fibrinolytic activity. To probe their roles on protease activity and substrate specificity, three residues of S3 site (Gly(100), Ser(101) and Leu(126)) were mutated by site-directed mutagenesis. Kinetics parameters of 20 mutants were measured using tetrapeptides as substrates, and their fibrinolytic activities were determined by fibrin plate method. Results of mutation analysis showed that Gly(100) and Ser(101) had reverse steric and electrostatic effects. Residues with bulky or positively charged side chains at position 100 decreased the substrate binding and catalytic activity drastically, while residues with the same characters at position 101 could obviously enhance protease and fibrinolytic activity of NK. Mutation of Leu(126) might impair the structure of the active cleft and drastically decreased the activity of NK. Kinetics studies of the mutants showed that S3 residues were crucial to keep protease activity while they moderately affected substrate specificity of NK. The present study provided some original insight into the P3-S3 interaction in NK and other subtilisins, as well as showed successful protein engineering cases to improve NK as a potential therapeutic agent.

Characterization on incineration residue of radioactive solid wastes

International Nuclear Information System (INIS)

Katoh, Kiyoshi; Hirayama, Katsuyoshi; Kato, Akira.

1989-01-01

Characterization was carried out on incineration residue discharged from the radioactive solid waste incineration unit (capacity, 100 kg/h) in use at the Tokai Research Establishment of Japan Atomic Energy Research Institute (JAERI) to obtain basic data for investigating solidification methods of the residue. The characterized residue was taken from furnace and a primary ceramic filter of the incineration unit which incinerates combustible solid wastes generated at JAERI and the outside organizations. Items of characterization involve a particle size distribution, misplaced materials content, ignition loss, chemical composition and radioactivity of nuclides in the ash. As the results, the size of ash sampled from the furnace distributed a wide range, with about 35∼60 % of ash smaller than 5 mm and about 10∼25 % of massive one larger than 30 mm (max. size: ∼130 mm). The ignition loss was 2∼3 %. The chemical compositions of the ash were mainly SiO 2 , Fe 2 O 3 , CaO and Al 2 O 3 . The specific activities of the ash were about 0.4∼4 x 10 3 Bq/g, and principal contaminants were 60 Co and 137 Cs. (author)

Pressure-induced metal-insulator transition in spinel compound CuV2S4

International Nuclear Information System (INIS)

Okada, H.; Koyama, K.; Hedo, M.; Uwatoko, Y.; Watanabe, K.

2008-01-01

In order to investigate the pressure effect on electrical properties of CuV 2 S 4 , we performed the electrical resistivity measurements under high pressures up to 8 GPa for a high-quality polycrystalline sample. The charge density wave (CDW) transition temperatures increase with increasing pressure. The residual resistivity rapidly increases with increasing pressure over 4 GPa, and the temperature dependence of the electrical resistivity at 8 GPa exhibits a semiconducting behavior below about 150 K, indicating that a pressure-induced metal-insulator transition occurs in CuV 2 S 4 at 8 GPa

Prediction of residual stresses in electron beam welded Ti-6Al-4V plates

Energy Technology Data Exchange (ETDEWEB)

Xu, Lianyong; Ge, Keke; Jing, Hongyang; Zhao, Lei; Lv, Xiaoqing [Tianjin Univ. (China); Han, Yongdian [Tianjin Univ. (China). Key Lab. of Advanced Joining Technology

2017-05-01

A thermo-metallurgical procedure based on the SYSWELD code was developed to predict welding temperature field, microstructure and residual stress in butt-welded Ti-6Al-4V plate taking into account phase transformation. The formation of martensite was confirmed by the CCT diagram and microstructure in the weld joint, which significantly affects the magnitude of residual stress. The hole drilling procedure was utilized to measure the values of residual stress at the top surface of the specimen, which are in well agreement with the numerical results. Both simulated and test results show that the magnitude and distribution of residual stress on the surface of the plate present a large gradient feature from the weld joint to the base metal. Moreover, the distribution law of residual stresses in the plate thickness was further analyzed for better understanding of its generation and evolution.

RESIDUAL STRESS MEASUREMENTS AND STRUCTURAL INTEGRITY IMPLICATIONS FOR SELECTIVE LASER MELTED TI-6AL-4V

Directory of Open Access Journals (Sweden)

Knowles, C. R.

2012-11-01

Full Text Available Selective laser melting (SLM of Ti-6Al-4V has significant potential in the aerospace and biotechnology industries. SLM employs a focused laser beam to melt successive layers of metallic powder into complex components. This process can result in the generation of high thermally-induced residual stresses. These residual stresses, together with micro-flaws/ pores from the inherent fabrication process, may lead to premature fatigue crack initiation and propagation at relatively low cyclic stresses. The hole-drilling strain gauge method was used to evaluate residual stresses within SLM Ti-6Al-4V specimens, with the intention of understanding the associated mechanisms for the successful application of SLM Ti-6Al-4V in industry.

4s24p3--4s4p4 and 4s24p3--4s2fp25s transitions in Y VII, Zr VIII, Nb IX, and MoX

International Nuclear Information System (INIS)

Reader, J.; Acquista, N.

1981-01-01

Spectra of ionized Y, Zr, Nb, and Mo have been observed in sliding-spark and triggered-spark discharges on 10.7-m normal- and grazing-incidence spectrographs at the National Bureau of Standards in Washington, D. C. From these observations the 4s 2 4p 3 --4s4p 4 transitions in Y VII, Zr VIII, Nb IX, and Mo X have been identified. The 4s 2 4p 3 --4s 2 4p 2 5s transitions in Y VII-Mo X, previously identified by Rahimullah et al. [Phys. Scr. 14, 221--223 (1976); 18, 96--106 (1978)], have been confirmed. In Y VII the 4s 2 4p 3 --4s 2 4p 2 6s and 4s4p 4 --4p 5 transition also have been found. The parameters obtained from least-squares fits to the energy levels are compared with Hartree--Fock calculations. Preliminary values of the ionization energies have been determined as 110.02 +- 0.15 eV for Y VII, 133.7 +- 0.5 eV for Zr VIII, 159.2 +- 0.7 eV for Nb IX, and 186.4 +- 1.2 eV for Mo X

Residual effects of ecstasy (3,4-methylenedioxymethamphetamine) on low level visual processes.

Science.gov (United States)

Murray, Elizabeth; Bruno, Raimondo; Brown, John

2012-03-01

'Ecstasy' (3,4-methylenedioxymethamphetamine) induces impaired functioning in the serotonergic system, including the occipital lobe. This study employed the 'tilt aftereffect' paradigm to operationalise the function of orientation-selective neurons among ecstasy consumers and controls as a means of investigating the role of reduced serotonin on visual orientation processing. The magnitude of the tilt aftereffect reflects the extent of lateral inhibition between orientation-selective neurons and is elicited to both 'real' contours, processed in visual cortex area V1, and illusory contours, processed in V2. The magnitude of tilt aftereffect to both contour types was examined among 19 ecstasy users (6 ecstasy only; 13 ecstasy-plus-cannabis users) and 23 matched controls (9 cannabis-only users; 14 drug-naive). Ecstasy users had a significantly greater tilt magnitude than non-users for real contours (Hedge's g = 0.63) but not for illusory contours (g = 0.20). These findings provide support for literature suggesting that residual effects of ecstasy (and reduced serotonin) impairs lateral inhibition between orientation-selective neurons in V1, which however suggests that ecstasy may not substantially affect this process in V2. Multiple studies have now demonstrated ecstasy-related deficits on basic visual functions, including orientation and motion processing. Such low-level effects may contribute to the impact of ecstasy use on neuropsychological tests of visuospatial function. Copyright © 2012 John Wiley & Sons, Ltd.

Nitrogen washing from C3 and C4 cover grasses residues by rain

Directory of Open Access Journals (Sweden)

Ciro Antonio Rosolem

2010-12-01

Full Text Available Crop species with the C4 photosynthetic pathway are more efficient in assimilating N than C3 plants, which results in different N amounts prone to be washed from its straw by rain water. Such differences may affect N recycling in agricultural systems where these species are grown as cover crops. In this experiment, phytomass production and N leaching from the straw of grasses with different photosynthetic pathways were studied in response to N application. Pearl millet (Pennisetum glaucum and congo grass (Brachiaria ruziziensis with the C4 photosynthetic pathway, and black oat (Avena Strigosa and triticale (X Triticosecale, with the C3 photosynthetic pathway, were grown for 47 days. After determining dry matter yields and N and C contents, a 30 mm rainfall was simulated over 8 t ha-1 of dry matter of each plant residue and the leached amounts of ammonium and nitrate were determined. C4 grasses responded to higher fertilizer rates, whereas N contents in plant tissue were lower. The amount of N leached from C4 grass residues was lower, probably because the C/N ratio is higher and N is more tightly bound to organic compounds. When planning a crop rotation system it is important to take into account the difference in N release of different plant residues which may affect N nutrition of the subsequent crop.

The s-process enrichment of the globular clusters M4 and M22

Energy Technology Data Exchange (ETDEWEB)

Shingles, Luke J.; Karakas, Amanda I.; Fishlock, Cherie K.; Yong, David; Da Costa, Gary S.; Marino, Anna F. [Research School of Astronomy and Astrophysics, Australian National University, Canberra, ACT 2611 (Australia); Hirschi, Raphael, E-mail: luke.shingles@anu.edu.au [Institute for the Physics and Mathematics of the Universe (WPI), University of Tokyo, 5-1-5 Kashiwanoha, 277-8583 Kashiwa (Japan)

2014-11-01

We investigate the enrichment in elements produced by the slow neutron-capture process (s-process) in the globular clusters M4 (NGC 6121) and M22 (NGC 6656). Stars in M4 have homogeneous abundances of Fe and neutron-capture elements, but the entire cluster is enhanced in s-process elements (Sr, Y, Ba, Pb) relative to other clusters with a similar metallicity. In M22, two stellar groups exhibit different abundances of Fe and s-process elements. By subtracting the mean abundances of s-poor from s-rich stars, we derive s-process residuals or empirical s-process distributions for M4 and M22. We find that the s-process distribution in M22 is more weighted toward the heavy s-peak (Ba, La, Ce) and Pb than M4, which has been enriched mostly with light s-peak elements (Sr, Y, Zr). We construct simple chemical evolution models using yields from massive star models that include rotation, which dramatically increases s-process production at low metallicity. We show that our massive star models with rotation rates of up to 50% of the critical (break-up) velocity and changes to the preferred {sup 17}O(α, γ){sup 21}Ne rate produce insufficient heavy s-elements and Pb to match the empirical distributions. For models that incorporate asymptotic giant branch yields, we find that intermediate-mass yields (with a {sup 22}Ne neutron source) alone do not reproduce the light-to-heavy s-element ratios for M4 and M22, and that a small contribution from models with a {sup 13}C pocket is required. With our assumption that {sup 13}C pockets form for initial masses below a transition range between 3.0 and 3.5 M {sub ☉}, we match the light-to-heavy s-element ratio in the s-process residual of M22 and predict a minimum enrichment timescale of between 240 and 360 Myr. Our predicted value is consistent with the 300 Myr upper limit age difference between the two groups derived from isochrone fitting.

Determination of residual 4'-aminomethyl-4,5',8-trimethylpsoralen and mutagenicity testing following psoralen plus UVA treatment of platelet suspensions

International Nuclear Information System (INIS)

Wagner, S.J.; Robinette, D.; Dodd, R.Y.; White, R.; Wolf, L.; Chapman, J.; Lawlor, T.E.

1993-01-01

Psoralens and UVa light have been used in the laboratory to study the inactivation of viruses that may be infrequently present in platelet concentrates prepared for transfusion. In order to evaluate safety aspects of the treatment of platelet suspensions with 4'-aminomethyl-4,5'8-trimethylpsoralen (AMT), the authors have investigated the residual levels and mutagenic potential of AMT after UVA phototreatment. The results suggest that residual available AMT is mutagenic in the AMES test and that the observed frameshift mutations may be caused by binding of AMt or its metabolites to nucleic acids in the absence of UVA light. (Author)

A finite element primer for beginners the basics

CERN Document Server

Zohdi, Tarek I

2014-01-01

The purpose of this primer is to provide the basics of the Finite Element Method, primarily illustrated through a classical model problem, linearized elasticity. The topics covered are:(1) Weighted residual methods and Galerkin approximations,(2) A model problem for one-dimensional?linear elastostatics,(3) Weak formulations in one dimension,(4) Minimum principles in one dimension,(5) Error estimation in one dimension,(5) Construction of Finite Element basis functions in one dimension,(6) Gaussian Quadrature,(7) Iterative solvers and element by element data structures,(8) A model problem for th

4D-PET reconstruction using a spline-residue model with spatial and temporal roughness penalties

Science.gov (United States)

Ralli, George P.; Chappell, Michael A.; McGowan, Daniel R.; Sharma, Ricky A.; Higgins, Geoff S.; Fenwick, John D.

2018-05-01

4D reconstruction of dynamic positron emission tomography (dPET) data can improve the signal-to-noise ratio in reconstructed image sequences by fitting smooth temporal functions to the voxel time-activity-curves (TACs) during the reconstruction, though the optimal choice of function remains an open question. We propose a spline-residue model, which describes TACs as weighted sums of convolutions of the arterial input function with cubic B-spline basis functions. Convolution with the input function constrains the spline-residue model at early time-points, potentially enhancing noise suppression in early time-frames, while still allowing a wide range of TAC descriptions over the entire imaged time-course, thus limiting bias. Spline-residue based 4D-reconstruction is compared to that of a conventional (non-4D) maximum a posteriori (MAP) algorithm, and to 4D-reconstructions based on adaptive-knot cubic B-splines, the spectral model and an irreversible two-tissue compartment (‘2C3K’) model. 4D reconstructions were carried out using a nested-MAP algorithm including spatial and temporal roughness penalties. The algorithms were tested using Monte-Carlo simulated scanner data, generated for a digital thoracic phantom with uptake kinetics based on a dynamic [18F]-Fluromisonidazole scan of a non-small cell lung cancer patient. For every algorithm, parametric maps were calculated by fitting each voxel TAC within a sub-region of the reconstructed images with the 2C3K model. Compared to conventional MAP reconstruction, spline-residue-based 4D reconstruction achieved  >50% improvements for five of the eight combinations of the four kinetics parameters for which parametric maps were created with the bias and noise measures used to analyse them, and produced better results for 5/8 combinations than any of the other reconstruction algorithms studied, while spectral model-based 4D reconstruction produced the best results for 2/8. 2C3K model-based 4D reconstruction generated

Fate of 2,4-D Residues in Turkish Soil-Plant Ecosystems

International Nuclear Information System (INIS)

Önal, Q.; Gözek, K.

1981-01-01

Full text: 2,4-D is the most frequently used herbicide in Turkish agriculture especially in Middle Anatolia. Studies on the behaviour of 2,4-D in the soil-plant ecosystem is being carried out under laboratory and field conditions. Some preliminary results are reported. After four weeks, recovery of radioactivity in carbon dioxide, aceton extract and bound residue was averaged for various soils: 20%, 15% and 48%, respectively. Barley, wheat and oat grown for four weeks on 2,4-D contaminated soil, contained from 0,6 up to 8% of the radioactivity applied. (author)

NMR of proteins (4Fe-4S): structural properties and intramolecular electron transfer

International Nuclear Information System (INIS)

Huber, J.G.

1996-01-01

NMR started to be applied to Fe-S proteins in the seventies. Its use has recently been enlarged as the problems arising from the paramagnetic polymetallic clusters ware overcome. Applications to [4Fe-4S] are presented herein. The information derived thereof deepens the understanding of the redox properties of these proteins which play a central role in the metabolism of bacterial cells. The secondary structure elements and the overall folding of Chromatium vinosum ferredoxin (Cv Fd) in solution have been established by NMR. The unique features of this sequence have been shown to fold as an α helix at the C-terminus and as a loop between two cysteines ligand of one cluster: these two parts localize in close proximity from one another. The interaction between nuclear and electronic spins is a source of additional structural information for (4Fe-AS] proteins. The conformation of the cysteine-ligands, as revealed by the Fe-(S γ -C β -H β )Cys dihedral angles, is related to the chemical shifts of the signals associated with the protons of these residues. The longitudinal relaxation times of the protons depend on their distance to the cluster. A quantitative relationship has been established and used to show that the solution structure of the high-potential ferredoxin from Cv differs significantly from the crystal structure around Phe-48. Both parameters (chemical shifts and longitudinal relaxation times) give also insight into the electronic and magnetic properties of the [4Fe-4S] clusters. The rate of intramolecular electron transfer between the two [4FE-4S] clusters of ferredoxins has been measured by NMR. It is far slower in the case of Cv Fd than for shorter ferredoxins. The difference may be associated with changes in the magnetic and/or electronic properties of one cluster. The strong paramagnetism of the [4Fe-4S] clusters, which originally limited the applicability of NMR to proteins containing these cofactors, has been proven instrumental in affording new

Residual stress measurements via neutron diffraction of additive manufactured stainless steel 17-4 PH.

Science.gov (United States)

Masoomi, Mohammad; Shamsaei, Nima; Winholtz, Robert A; Milner, Justin L; Gnäupel-Herold, Thomas; Elwany, Alaa; Mahmoudi, Mohamad; Thompson, Scott M

2017-08-01

Neutron diffraction was employed to measure internal residual stresses at various locations along stainless steel (SS) 17-4 PH specimens additively manufactured via laser-powder bed fusion (L-PBF). Of these specimens, two were rods (diameter=8 mm, length=80 mm) built vertically upward and one a parallelepiped (8×80×9 mm 3 ) built with its longest edge parallel to ground. One rod and the parallelepiped were left in their as-built condition, while the other rod was heat treated. Data presented provide insight into the microstructural characteristics of typical L-PBF SS 17-4 PH specimens and their dependence on build orientation and post-processing procedures such as heat treatment. Data have been deposited in the Data in Brief Dataverse repository (doi:10.7910/DVN/T41S3V).

Residual stress measurements via neutron diffraction of additive manufactured stainless steel 17-4 PH

Directory of Open Access Journals (Sweden)

Mohammad Masoomi

2017-08-01

Full Text Available Neutron diffraction was employed to measure internal residual stresses at various locations along stainless steel (SS 17-4 PH specimens additively manufactured via laser-powder bed fusion (L-PBF. Of these specimens, two were rods (diameter=8 mm, length=80 mm built vertically upward and one a parallelepiped (8×80×9 mm3 built with its longest edge parallel to ground. One rod and the parallelepiped were left in their as-built condition, while the other rod was heat treated. Data presented provide insight into the microstructural characteristics of typical L-PBF SS 17-4 PH specimens and their dependence on build orientation and post-processing procedures such as heat treatment. Data have been deposited in the Data in Brief Dataverse repository (doi:10.7910/DVN/T41S3V.

Agronomic Use of Basic Slag

Directory of Open Access Journals (Sweden)

Fabio Oliveiri de Nobile

2015-01-01

Full Text Available Modern civilization, in recent years, has increased the requirement of products derived from iron and steel, stimulating the growth of the national siderurgical sector and, consequently, the generation of industrial residue called basic slag. In this context, the recycling of residues can contribute to solve problems of the industries that give priority to the excellence of the production with quality. On the other hand, there is a sector of primary production in Brazil, the agriculture, with a great cultivated area in acid ground and with low fertility, being these factors admittedly determinative for vegetal production, under tropical conditions. Thus, there is a scenery of two primary sectors of production, although distinct ones, that present interaction potential, for , on one hand, there is disponibility of a product with similar properties to the liming materials and traditional fertilizers and, on the other hand, a production sector that is highly dependent of these products. And the interaction between these two sectors helps in the preservation of the environment, bringing, thus, a certain sustainability in the production systems of the postmodern civilization that will be the challenge of this new century. Considering the current possibility of recycling these industrial residues in agriculture, three important factors have to be taken into account. The first would be the proper use of the abundant, available and promising industrial residue; the second, in a propitious agricultural environment, acid soil and low fertility; and third, in a responsive and important socio-economic culture, the sugar cane, considering its vast cultivated area. In national literature, few works have dealt with the use of the basic slag and have evaluated the reply of the cultures to its application. Thus, the present work had as its aim to gather information from literature concerning the characterization and production of basic slag in Brazil, as well

Compostagem da fração sólida da água residuária de suinocultura Solid fraction composting of residual water from pig farms

Directory of Open Access Journals (Sweden)

Marco A. P. Orrico Júnior

2009-09-01

Full Text Available Avaliar o desenvolvimento do processo de compostagem utilizando como substrato à fração sólida da água residuária de suinocultura foi o objetivo deste trabalho. Para a obtenção da fração sólida, a água residuária de suinocultura foi submetida ao peneiramento, utilizando-se de peneira com malha de 1 milímetro. Após separação, a fração sólida foi utilizada para a confecção de três leiras de compostagem, em pátio com piso de concreto e cobertura plástica. Durante a compostagem da fração sólida da água residuária de suinocultura, foram avaliados: temperatura, reduções de sólidos totais (ST, sólidos voláteis (SV, demanda química de oxigênio (DQO, carbono orgânico, matéria orgânica compostável (MOC, matéria orgânica resistente à compostagem (MORC, números mais prováveis (NMPs de coliformes totais e coliformes termotolerantes, além do volume e dos teores de nutrientes no composto. A compostagem mostrou-se eficiente no tratamento da fração sólida da água residuária de suinocultura devido à elevada minimização do poder poluente dos dejetos, observando-se reduções de 71,24% nos teores de ST, 64,55% no volume, 56,89% no teor de DQO e 56,89% na MOC. Foram verificadas reduções de 100% nos NMPs de coliformes totais e termotolerantes, o que possibilita seu uso como adubo orgânico.This work aimed to evaluate the development of the composting process by using the solid fraction of residual water from a pig farm. To obtain the solid fraction, the residual water was sewed in a 1mm screen sew. After separation, the solid fraction was used to form three composting piles, on a patio with concrete floor and plastic cover. During composting the solid fraction of residual water from pig farms was monitored: temperature, total solids reduction (TS, volatile solids (VS chemical demand for oxygen (CDO, organic carbon, compostable organic matter (COM, organic matter resistant to composting (OMRC, most probable

The Yin and Yang of SagS: Distinct Residues in the HmsP Domain of SagS Independently Regulate Biofilm Formation and Biofilm Drug Tolerance

Science.gov (United States)

Dingemans, Jozef; Poudyal, Bandita

2018-01-01

ABSTRACT The formation of inherently drug-tolerant biofilms by the opportunistic pathogen Pseudomonas aeruginosa requires the sensor-regulator hybrid SagS, with ΔsagS biofilms being unstructured and exhibiting increased antimicrobial susceptibility. Recent findings indicated SagS to function as a switch to control biofilm formation and drug tolerance independently. Moreover, findings suggested the periplasmic sensory HmsP domain of SagS is likely to be the control point in the regulation of biofilm formation and biofilm cells transitioning to a drug-tolerant state. We thus asked whether specific amino acid residues present in the HmsP domain contribute to the switch function of SagS. HmsP domain residues were therefore subjected to alanine replacement mutagenesis to identify substitutions that block the sensory function(s) of SagS, which is apparent by attached cells being unable to develop mature biofilms and/or prevent transition to an antimicrobial-resistant state. Mutant analyses revealed 32 residues that only contribute to blocking one sensory function. Moreover, amino acid residues affecting attachment and subsequent biofilm formation but not biofilm tolerance also impaired histidine kinase signaling via BfiS. In contrast, residues affecting biofilm drug tolerance but not attachment and subsequent biofilm formation negatively impacted BrlR transcription factor levels. Structure prediction suggested the two sets of residues affecting sensory functions are located in distinct areas that were previously described as being involved in ligand binding interactions. Taken together, these studies identify the molecular basis for the dual regulatory function of SagS. IMPORTANCE The membrane-bound sensory protein SagS plays a pivotal role in P. aeruginosa biofilm formation and biofilm cells gaining their heightened resistance to antimicrobial agents, with SagS being the control point at which both pathways diverge. Here, we demonstrate for the first time that the two

Contribution of the residue at position 4 within classical nuclear localization signals to modulating interaction with importins and nuclear targeting.

Science.gov (United States)

Smith, Kate M; Di Antonio, Veronica; Bellucci, Luca; Thomas, David R; Caporuscio, Fabiana; Ciccarese, Francesco; Ghassabian, Hanieh; Wagstaff, Kylie M; Forwood, Jade K; Jans, David A; Palù, Giorgio; Alvisi, Gualtiero

2018-08-01

Nuclear import involves the recognition by importin (IMP) superfamily members of nuclear localization signals (NLSs) within protein cargoes destined for the nucleus, the best understood being recognition of classical NLSs (cNLSs) by the IMPα/β1 heterodimer. Although the cNLS consensus [K-(K/R)-X-(K/R) for positions P2-P5] is generally accepted, recent studies indicated that the contribution made by different residues at the P4 position can vary. Here, we apply a combination of microscopy, molecular dynamics, crystallography, in vitro binding, and bioinformatics approaches to show that the nature of residues at P4 indeed modulates cNLS function in the context of a prototypical Simian Virus 40 large tumor antigen-derived cNLS (KKRK, P2-5). Indeed, all hydrophobic substitutions in place of R impaired binding to IMPα and nuclear targeting, with the largest effect exerted by a G residue at P4. Substitution of R with neutral hydrophobic residues caused the loss of electrostatic and van der Waals interactions between the P4 residue side chains and IMPα. Detailed bioinformatics analysis confirmed the importance of the P4 residue for cNLS function across the human proteome, with specific residues such as G being associated with low activity. Furthermore, we validate our findings for two additional cNLSs from human cytomegalovirus (HCMV) DNA polymerase catalytic subunit UL54 and processivity factor UL44, where a G residue at P4 results in a 2-3-fold decrease in NLS activity. Our results thus showed that the P4 residue makes a hitherto poorly appreciated contribution to nuclear import efficiency, which is essential to determining the precise nuclear levels of cargoes. Copyright © 2018 Elsevier B.V. All rights reserved.

Scanning electron-acoustic imaging of residual stress distributions in aluminum metal and ZrSiO4 multiphase ceramics

International Nuclear Information System (INIS)

Zhang, B.Y.; Jiang, F.M.; Shi, Y.; Yin, Q.R.; Qian, M.L.

1997-01-01

The scanning electron-acoustic imaging technique has been used in the characterization of the residual stress field distributions existing in the subsurface in aluminum disks and 20 vol% SiC ( w)/ZrSiO 4 multiphase ceramics left by Vicker close-quote s indentation. The experimental results reveal that the distribution areas are the plastic-elastic interchange zones. The electron-acoustic signal generation mechanism in the samples are discussed. copyright 1997 American Institute of Physics

Residues and dissipation of kresoxim methyl in apple under field condition.

Science.gov (United States)

Malhat, Farag; Kamel, Essam; Saber, Ayman; Hassan, Ehab; Youssef, Ahmed; Almaz, Monir; Hassan, Ayman; Fayz, Abd El-Salam

2013-09-01

The dissipation and residual levels of kresoxim methyl in apple under field condition were determined by using HPLC-DAD with QuEChERS method. At fortification levels of 0.05, 0.1, 0.5 and 1.0 mg kg(-1) in apple, it was shown that recoveries were ranged from 91.1% to 96.9% with coefficient variation of the method (CV%) for repeatability ranged from 1.27% to 4.77%. The limit of quantification (LOQ) of the method was 0.05 mg kg(-1). The dissipation rates of kresoxim methyl were described by using first-order kinetics and its half-life, as they are ranged from 4.58 to 4.77 days in apple. The terminal residues of kresoxim methyl were below the FAO/WHO maximum residue limit (MRL, 0.2 mg kg(-1)) in apple when measured 14 days after the final application, which suggested that the use of this fungicide was safe for humans. This study would help in providing the basic information for developing regulation to guard a safe use of kresoxim methyl in apple orchard and to prevent health problem from consumers. Copyright © 2013 Elsevier Ltd. All rights reserved.

Biochemical identification of residues that discriminate between 3,4-dihydroxyphenylalanine decarboxylase and 3,4-dihydroxyphenylacetaldehyde synthase-mediated reactions.

Science.gov (United States)

Liang, Jing; Han, Qian; Ding, Haizhen; Li, Jianyong

2017-12-01

In available insect genomes, there are several L-3,4-dihydroxyphenylalanine (L-dopa) decarboxylase (DDC)-like or aromatic amino acid decarboxylase (AAAD) sequences. This contrasts to those of mammals whose genomes contain only one DDC. Our previous experiments established that two DDC-like proteins from Drosophila actually mediate a complicated decarboxylation-oxidative deamination process of dopa in the presence of oxygen, leading to the formation of 3,4-dihydroxyphenylacetaldehyde (DHPA), CO 2 , NH 3, and H 2 O 2 . This contrasts to the typical DDC-catalyzed reaction, which produces CO 2 and dopamine. These DDC-like proteins were arbitrarily named DHPA synthases based on their critical role in insect soft cuticle formation. Establishment of reactions catalyzed by these AAAD-like proteins solved a puzzle that perplexed researchers for years, but to tell a true DHPA synthase from a DDC in the insect AAAD family remains problematic due to high sequence similarity. In this study, we performed extensive structural and biochemical comparisons between DHPA synthase and DDC. These comparisons identified several target residues potentially dictating DDC-catalyzed and DHPA synthase-catalyzed reactions, respectively. Comparison of DHPA synthase homology models with crystal structures of typical DDC proteins, particularly residues in the active sites, provided further insights for the roles these identified target residues play. Subsequent site-directed mutagenesis of the tentative target residues and activity evaluations of their corresponding mutants determined that active site His192 and Asn192 are essential signature residues for DDC- and DHPA synthase-catalyzed reactions, respectively. Oxygen is required in DHPA synthase-mediated process and this oxidizing agent is reduced to H 2 O 2 in the process. Biochemical assessment established that H 2 O 2 , formed in DHPA synthase-mediated process, can be reused as oxidizing agent and this active oxygen species is reduced to H 2

Deliberated opinion of the Environment Authority on the ECRIN basic nuclear installation 'confined warehousing of residues produced by conversion' (11)

International Nuclear Information System (INIS)

2013-01-01

This report proposes an environmental review of the creation authorization request for a basic nuclear installation (INB), the ECRIN INB in Malvesi, for the confined warehousing of residues produced by uranium conversion (transformation into uranium tetrafluoride). After having formulated the main recommendations regarding the style and content of this request, this report presents and comments the context, the project and its environmental stakes, indicates the concerned administrative procedures, discusses the project content and the projected works. It proposes an analysis and a discussion of the impact study and makes recommendations to improve it. This analysis addresses the site environmental initial condition, possible alternative solutions, the dismantling plan, various temporary or permanent impacts of the project, the risk management study, and follow-up measures

Evaluation of Residual Stresses using Ring Core Method

Directory of Open Access Journals (Sweden)

Holý S.

2010-06-01

Full Text Available The method for measuring residual stresses using ring-core method is described. Basic relations are given for residual stress measurement along the specimen depth and simplified method is described for average residual stress estimation in the drilled layer for known principal stress directions. The estimation of calculated coefficients using FEM is described. Comparison of method sensitivity is made with hole-drilling method. The device for method application is described and an example of experiment is introduced. The accuracy of method is discussed. The influence of strain gauge rosette misalignment to the evaluated residual stresses is performed using FEM.

Characterization of the Young's modulus and residual stresses for a sputtered silicon oxynitride film using micro-structures

International Nuclear Information System (INIS)

Dong, Jian; Du, Ping; Zhang, Xin

2013-01-01

Silicon oxynitride (SiON) is an important material to fabricate micro-electro-mechanical system (MEMS) devices due to its composition-dependent tunability in electronic and mechanical properties. In this work, the SiON film with 41.45% silicon, 32.77% oxygen and 25.78% nitrogen content was deposited by RF magnetron sputtering. Two types of optimized micro-structures including micro-cantilevers and micro-rotating-fingers were designed and fabricated using MEMS surface micromachining technology. The micro-cantilever bending tests were conducted using a nanoindenter to characterize the Young's modulus of the SiON film. Owing to the elimination of the residual stress effect on the micro-cantilever structure, higher accuracy in the Young's modulus was achieved from this technique. With the information of Young's modulus of the film, the residual stresses were characterized from the deflection of the micro-rotating-fingers. This structure was able to locally measure a large range of tensile or compressive residual stresses in a thin film with sufficient sensitivities. The results showed that the Young's modulus of the SiON film was 122 GPa and the residual stresses of the SiON film were 327 MPa in the crystallographic orientation of the wafer and 334 MPa in the direction perpendicular to the crystallographic orientation, both in compression. This work presents a comprehensive methodology to measure the Young's modulus and residual stresses of a thin film with improved accuracy, which is promising for applications in mechanical characterization of MEMS devices. - Highlight: • We measured the Young's modulus and residual stress of SiON film by microstructure. • Micro cantilever structure improved the Young's modulus' measurement accuracy. • We explored the reason for the deviations of residual stress value of SiON film

Effects of fretting fatigue on the residual stress of shot peened Ti-6Al-4V samples

International Nuclear Information System (INIS)

Martinez, S.A.; Sathish, S.; Blodgett, M.P.; Mall, S.; Namjoshi, S.

2005-01-01

X-ray diffraction residual stress measurement has been utilized as nondestructive tool for the characterization of fretting fatigue damage in shot peened samples of Ti-6Al-4V. Prior to fretting fatigue damage, compressive residual stresses were found to be uniform over the entire face of the sample and independent of the measurement direction. After fretting fatigue, inside and in the vicinity of the fretting damage zone large relaxation of compressive residual stress was observed. An anisotropic residual stress distribution has been observed in the fretting fatigue damaged region. Residual stress measurements in interrupted fretting fatigue experiments showed that the relaxation of residual stress increases as the number of fretting fatigue cycles increase. The results are discussed in the light of their importance in establishing X-ray diffraction residual stress measurement technique as a nondestructive tool to characterize fretting fatigue damage

Control levels for residual contamination in materials considered for recycle and reuse

International Nuclear Information System (INIS)

Hill, R.L.; Aaberg, R.L.; Baker, D.A.; Kennedy, W.E. Jr.

1993-09-01

Pacific Northwest Laboratory (PNL) is collecting data and conducting technical analyses to support joint efforts by the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water and Radiation Division (DOE/EH-232); by the U.S. Environmental Protection Agency (EPA); and by the U.S. Nuclear Regulatory Commission (NRC) to develop radiological control criteria for the recycle and reuse of scrap materials and equipment that contain residual radioactive contamination. The initial radiological control levels are the concentrations in or on materials considered for recycle or reuse that meet the individual (human) or industrial (electronics/film) dose criteria. The analysis identifies relevant radionuclides, potential mechanisms of exposure, and methods to determine possible non-health-related impacts from residual radioactive contamination in materials considered for recycle or reuse. The generic methodology and scenarios described here provide a basic framework for numerically deriving radiological control criteria for recycle or reuse. These will be adequately conservative for most situations

High-resolution orientation and depth of insertion of the voltage-sensing S4 helix of a potassium channel in lipid bilayers.

Science.gov (United States)

Doherty, Tim; Su, Yongchao; Hong, Mei

2010-08-27

The opening and closing of voltage-gated potassium (Kv) channels are controlled by several conserved Arg residues in the S4 helix of the voltage-sensing domain. The interaction of these positively charged Arg residues with the lipid membrane has been of intense interest for understanding how membrane proteins fold to allow charged residues to insert into lipid bilayers against free-energy barriers. Using solid-state NMR, we have now determined the orientation and insertion depth of the S4 peptide of the KvAP channel in lipid bilayers. Two-dimensional (15)N correlation experiments of macroscopically oriented S4 peptide in phospholipid bilayers revealed a tilt angle of 40 degrees and two possible rotation angles differing by 180 degrees around the helix axis. Remarkably, the tilt angle and one of the two rotation angles are identical to those of the S4 helix in the intact voltage-sensing domain, suggesting that interactions between the S4 segment and other helices of the voltage-sensing domain are not essential for the membrane topology of the S4 helix. (13)C-(31)P distances between the S4 backbone and the lipid (31)P indicate a approximately 9 A local thinning and 2 A average thinning of the DMPC (1,2-dimyristoyl-sn-glycero-3-phosphochloline)/DMPG (1,2-dimyristoyl-sn-glycero-3-phosphatidylglycerol) bilayer, consistent with neutron diffraction data. Moreover, a short distance of 4.6 A from the guanidinium C(zeta) of the second Arg to (31)P indicates the existence of guanidinium phosphate hydrogen bonding and salt bridges. These data suggest that the structure of the Kv gating helix is mainly determined by protein-lipid interactions instead of interhelical protein-protein interactions, and the S4 amino acid sequence encodes sufficient information for the membrane topology of this crucial gating helix. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Beta lactam antibiotics residues in cow’s milk: comparison of efficacy of three screening tests used in Bosnia and Herzegovina

Science.gov (United States)

Fejzić, Nihad; Begagić, Muris; Šerić-Haračić, Sabina; Smajlović, Muhamed

2014-01-01

Beta lactam antibiotics are widely used in therapy of cattle, particularly for the treatment of mastitis. Over 95% of residue testing in dairies in Bosnia and Herzegovina is for Beta lactams. The aim of this paper is to compare the efficacy of three most common screening tests for Beta lactam residues in cow’s milk in our country. The tests used in the study are SNAP β Lactam test (Idexx), Rosa Charm β Lactam test (Charm Sciences) and Inhibition MRL test (A&M). Study samples included: standardized concentrations of penicillin solution (0, 2, 3, 4, 5 and 6 ppb). In addition we tested milk samples from three equal size study groups (not receiving any antibiotic therapy, treated with Beta lactams for mastitis and treated with Beta lactams for diseases other than mastitis). Sensitivity and specificity were determined for each test, using standard penicillin concentrations with threshold value set at concentration of 4 ppb (Maximum residue level – MLR). Additionally we determined proportions of presumably false negative and false positive results for each test using results of filed samples testing. Agreement of test results for each test pair was assessed through Kappa coefficients interpreted by Landis-Koch scale. Detection level of all tests was shown to be well below MRL. This alongside with effects of natural inhibitors in milk contributed to finding of positive results in untreated and treated animals after the withholding period. Screening tests for beta lactam residues are important tools for ensuring that milk for human consumption is free from antibiotics residues. PMID:25172975

Simultaneous stabilization/solidification of Mn2+ and NH4+-N from electrolytic manganese residue using MgO and different phosphate resource.

Science.gov (United States)

Shu, Jiancheng; Wu, Haiping; Liu, Renlong; Liu, Zuohua; Li, Bing; Chen, Mengjun; Tao, Changyuan

2018-02-01

This study examined simultaneous stabilization and solidification (S/S) of Mn 2+ and NH 4 + -N from electrolytic manganese residue (EMR) using MgO and different phosphate resource. The characteristics of EMR NH 4 + -N and Mn 2+ S/S behavior, S/S mechanisms, leaching test and economic analysis, were investigated. The results show that the S/S efficiency of Mn 2+ and NH 4 + -N could reach 91.58% and 99.98%, respectively, and the pH value is 8.75 when the molar ratio of Mg:P is 3:1 and the dose of PM (MgO and Na 3 PO 4 ·12H 2 O) is 8wt%. In this process, Mn 2+ could mainly be stabilized in the forms of Mn(H 2 PO 4 ) 2 ·2H 2 O, Mn 3 (PO 4 ) 2 ·3H 2 O, Mn(OH) 2 , and MnOOH, and NH 4 + -N in the form of NH 4 MgPO 4 ·6H 2 O. Economic evaluation indicates that using PM process has a lower cost than HPM and HOM process for the S/S of Mn 2+ and NH 4 + -N from EMR at the same stabilization agent dose. Leaching test values of all the measured metals are within the permitted level for the GB8978-1996 test suggested when the dose of PM, HPM and HOM is 8wt%. Copyright © 2017 Elsevier Inc. All rights reserved.

AQP4 plasma membrane trafficking or channel gating is not significantly modulated by phosphorylation at C-terminal serine residues

DEFF Research Database (Denmark)

Assentoft, Mette; Larsen, Brian R; Olesen, Emma T B

2014-01-01

heterologous expression in Xenopus laevis oocytes (along with serine-to-aspartate mutants of the same residues to mimic a phosphorylation). None of the mutant AQP4 constructs displayed alterations in the unit water permeability. Thus phosphorylation of six different serine residues in the COOH terminus of AQP4....... Phosphorylation of aquaporins can regulate plasma membrane localization and, possibly, the unit water permeability via gating of the AQP channel itself. In vivo phosphorylation of six serine residues in the COOH terminus of AQP4 has been detected by mass spectrometry: Ser(276), Ser(285), Ser(315), Ser(316), Ser...

Basic residues in the 74-83 and 191-198 segments of protein kinase CK2 catalytic subunit are implicated in negative but not in positive regulation by the beta-subunit

DEFF Research Database (Denmark)

Sarno, S; Vaglio, P; Marin, O

1997-01-01

by the beta-subunit many fold more than that of alpha wild type, while extrastimulation by beta mutant D55L56E57A, observable with alpha wild type, is abolished with these mutants. These data support the conclusion that down regulation by the acidic residues clustered in the N-terminal moiety of beta...... is mediated by basic residues in the 74-83 and in the 191-198 sequences of the alpha-subunit. These are also implicated in substrate recognition consistent with the concept that the N-terminal acidic region of the beta subunit operates as a pseudosubstrate. In contrast, another CK2alpha mutant, V66A, is more...

Determination of residual 4'-aminomethyl-4,5',8-trimethylpsoralen and mutagenicity testing following psoralen plus UVA treatment of platelet suspensions

Energy Technology Data Exchange (ETDEWEB)

Wagner, S.J.; Robinette, D.; Dodd, R.Y. (American Red Cross Blood Services, Rockville, MD (United States). Jerome H. Holland Lab. for Biomedical Sciences); White, R.; Wolf, L.; Chapman, J. (Baxter Biotech, Round Lake, IL (United States). Fenwal Labs.); Lawlor, T.E. (Hazleton Labs., Vienna, VA (United States). Molecular and Cellular Toxicology)

1993-05-01

Psoralens and UVa light have been used in the laboratory to study the inactivation of viruses that may be infrequently present in platelet concentrates prepared for transfusion. In order to evaluate safety aspects of the treatment of platelet suspensions with 4'-aminomethyl-4,5'8-trimethylpsoralen (AMT), the authors have investigated the residual levels and mutagenic potential of AMT after UVA phototreatment. The results suggest that residual available AMT is mutagenic in the AMES test and that the observed frameshift mutations may be caused by binding of AMt or its metabolites to nucleic acids in the absence of UVA light. (Author).

Contributions of basic amino acids in the autolysis loop of factor XIa to serpin specificity.

Science.gov (United States)

Rezaie, Alireza R; Sun, Mao-fu; Gailani, David

2006-08-08

The autolysis loops (amino acids 143-154, chymotrypsinogen numbering) of plasma serine proteases play key roles in determining the specificity of protease inhibition by plasma serpins. We studied the importance of four basic residues (Arg-144, Lys-145, Arg-147, and Lys-149) in the autolysis loop of the coagulation protease factor XIa (fXIa) for inhibition by serpins. Recombinant fXIa mutants, in which these residues were replaced individually or in combination with alanine, were prepared. The proteases were compared to wild-type fXIa (fXIa-WT) with respect to their ability to activate factor IX in a plasma clotting assay, to hydrolyze the chromogenic substrate S2366, and to undergo inhibition by the C1-inhibitor (C1-INH), protein Z dependent protease inhibitor (ZPI), antithrombin (AT), and alpha(1)-protease inhibitor (alpha(1)-PI). All mutants exhibited normal activity in plasma and hydrolyzed S2366 with catalytic efficiencies similar to that of fXIa-WT. Inhibition of mutants by C1-INH was increased to varying degrees relative to that of fXIa-WT, with the mutant containing alanine replacements for all four basic residues (fXIa-144-149A) exhibiting an approximately 15-fold higher rate of inhibition. In contrast, the inhibition by ZPI was impaired 2-3-fold for single amino acid substitutions, and fXIa-144-149A was essentially resistant to inhibition by ZPI. Alanine substitution for Arg-147 impaired inhibition by AT approximately 7-fold; however, other substitutions did not affect it or slightly enhanced inhibition. Arg-147 was also required for inhibition by alpha(1)-PI. Cumulatively, the results demonstrate that basic amino acids in the autolysis loop of fXIa are important determinants of serpin specificity.

Residual stress in TI6AL4V objects produced by direct metal laser sintering

Directory of Open Access Journals (Sweden)

Van Zyl, Ian

2016-12-01

Full Text Available Direct Metal Laser Sintering produces 3D objects using a layer-by- layer method in which powder is deposited in thin layers. Laser beam scans over the powder fusing powder particles as well as the previous layer. High-concentration of laser energy input leads to high thermal gradients which induce residual stress within the as- built parts. Ti6Al4V (ELI samples have been manufactured by EOSINT M280 system at prescribed by EOS process-parameters. Residual stresses were measured by XRD method. Microstructure, values and directions of principal stresses inTi6Al4V DMLS samples were analysed.

A ProCoS II Project Final Report: ESPRIT Basic Research project 707

DEFF Research Database (Denmark)

Bowen, J. P.; Hoare, C. A. R.; Langmaack, Hans

1996-01-01

An overview of the research and associated activities of the Europeancollaborative ESPRIT Basic Research ProCoS II project (no. 7071) on``Provably Correct Systems'' which ran from 1992 to 1995 is presented.This was a follow-on project to ProCoS (no. 3104) and ran inparallel with the ProCoS Working...

Geochemical modeling of leaching from MSVI air-pollution-control residues

DEFF Research Database (Denmark)

Astrup, Thomas; Dijkstra, J.J.; Comans, R.N.J.

2006-01-01

This paper provides an improved understanding of the leaching behavior of waste incineration air-pollution-control (APC) residues in a long-term perspective. Leaching was investigated by a series of batch experiments reflecting leaching conditions after initial washout of highly soluble salts from...... residues. Leaching experiments were performed at a range of pH-values using carbonated and noncarbonated versions of two APC residues. The leaching data were evaluated by geochemical speciation modeling and discussed with respect to possible solubility control. The leaching of major elements as well...... of Al, Ba, Ca, Cr, Pb, S, Si, V, and Zn was found influenced by solubility control from Al2O3, Al(OH)3, Ba(S,Cr)O4 solid solutions, BaSO4, Ca6Al2(SO4)3(OH)12â26H2O, CaAl2Si4O12â2H2O, Ca-(OH)2, CaSiO3, CaSO4â2H2O, CaZn2(OH)6â2H2O, KAlSi2O6, PbCO3, PbCrO4, Pb2O3, Pb2V2O7, Pb3(VO4)2, ZnO, Zn2SiO4, and Zn...

A basic design of SR4 instrumentation and control system for research reactor

International Nuclear Information System (INIS)

Syahrudin Yusuf; M Subhan; Ikhsan Shobari; Sutomo Budihardjo

2010-01-01

An SR4 instrumentation and control systems of research reactor is the equipment of nuclear research reactors as power protection devices and control systems. The equipment is to monitor safety parameters and process parameters in the state of reactor shut down, start-up, and in operation at fixed power. In the engineering of Instrumentation and control systems SR4 research reactor, its basic design consists of technical specifications of the reactor protection system devices, technical specifications of the reactor power control system devices, technical specifications information system devices, and systems process termination cabling as a support system. This basic design is used as the basis for the preparation of detailed design and subsequent engineering development of instrumentation systems and control system integrated. (author)

Evaporation residue corss sections for {sup 32}S + {sup 184}W

Energy Technology Data Exchange (ETDEWEB)

Back, B.B.; Blumenthal, D.J.; Davids, C.N. [and others

1995-08-01

We recently measured evaporation residue cross sections for the {sup 32}S + {sup 184}W system over a range of beam energies using the Argonne Fragment Mass Analyzer (FMA). Absolute cross sections were obtained on the basis of the recent determination of the transmission probability through the FMA of heavy, slow-moving reaction products. The measurements were carried out using {sup 32}S-beams from the ATLAS superconducting linac at Argonne. Beam energies of 165, 174, 185, 195, 205, 215, 225, 236, 246, and 257 MeV were used. The sliding-seal target chamber is used to allow for measurements at finite angles.

Emissions of N2O and CH4 from agricultural soils amended with two types of biogas residues

International Nuclear Information System (INIS)

Odlare, M.; Abubaker, J.; Lindmark, J.; Pell, M.; Thorin, E.; Nehrenheim, E.

2012-01-01

Biogas residues contain valuable plant nutrients, important to the crops and also to soil microorganisms. However, application of these materials to the soils may contribute to the emission of greenhouse gases (GHG) causing global warming and climate change. In the present study, incubation experiment was carried out, where the emission rates of N 2 O and CH 4 were measured after amending two soils with two types of biogas residues: (1) a regular residue from a large scale biogas plant (BR) and (2) a residue from an ultra-filtration membrane unit connected to a pilot-scale biogas plant (BRMF). The emissions of N 2 O and CH 4 were measured at two occasions: at 24 h and at 7 days after residue amendment, respectively. Amendment with filtered biogas residues (BRMF) led to an increase in N 2 O emissions with about 6–23 times in organic and clay soil, respectively, in comparison to unfiltered biogas residues (BR). Methane emission was detected in small amounts when filtered biogas residue was added to the soil. Amendment of unfiltered biogas to the organic soil resulted in net consumption. In conclusion, fertilization with BRMF can be combined with risk of an increase N 2 O emission, especially when applied to organic soils. However, in order to transfer these results to real life agriculture, large scale field studies need to be carried out. -- Highlights: ► Membrane filtration of biogas process water is a promising method. ► Fertilization of biogas residue may increase the N 2 O emission from soil. ► Organic soils produced higher emissions than clay soils.

PERVALE-S: a new cognitive task to assess deaf people’s ability to perceive basic and social emotions

Directory of Open Access Journals (Sweden)

JOSE MIGUEL MESTRE

2015-08-01

Full Text Available PERVALE-S was developed to assess the ability of DP to perceive both social and basic emotions. PERVALE-S presents different sets of visual images of a real deaf person expressing both basic and social emotions, according to the normative standard of emotional expressions in Spanish sign language. Emotional expression stimuli were presented at two different levels of intensity (1: low; and 2: high because DP do not distinguish the same range of frequency adverbs as hearing people (HP do. Then, participants had to click on the more suitable emotional expression. PERVALE-S contains video instructions of a sign language interpreter to improve DP’s understanding about how to use the software. DP had to watch the videos before answering the items. To test PERVALE-S, a sample of 56 individuals was recruited (18 signers, 8 lip-readers, and 30 hearing people. Participants also responded to a personality test (HSPQ adapted and a fluid intelligence measure (RAPM. Moreover, four teachers from deaf center rated all deaf participants. Results: there were no significant differences between DP and HP in performance in PERVALE-S. Confusion matrices revealed that embarrassment, envy, and jealousy were worse perceived by participants (DP and HP. There were not significant differences of emotional perception performance among lip-readings, signers, and hearings. Regarding emotional perception ability (EPA, basic emotion performance was positively related to consciousness, and negatively with tension. Social emotion performance was positively related to age and fluid intelligence, and negatively related to dominance. When an adapted instrument for assessing EPA is developed without language implications, the performance among DP and HP are closer. This instrument could have experimental interest in order of eliminating language influences in EPA.

PERVALE-S: a new cognitive task to assess deaf people’s ability to perceive basic and social emotions

Science.gov (United States)

Mestre, José M.; Larrán, Cristina; Herrero, Joaquín; Guil, Rocío; de la Torre, Gabriel G.

2015-01-01

A poorly understood aspect of deaf people (DP) is how their emotional information is processed. Verbal ability is key to improve emotional knowledge in people. Nevertheless, DP are unable to distinguish intonation, intensity, and the rhythm of language due to lack of hearing. Some DP have acquired both lip-reading abilities and sign language, but others have developed only sign language. PERVALE-S was developed to assess the ability of DP to perceive both social and basic emotions. PERVALE-S presents different sets of visual images of a real deaf person expressing both basic and social emotions, according to the normative standard of emotional expressions in Spanish Sign Language. Emotional expression stimuli were presented at two different levels of intensity (1: low; and 2: high) because DP do not distinguish an object in the same way as hearing people (HP) do. Then, participants had to click on the more suitable emotional expression. PERVALE-S contains video instructions (given by a sign language interpreter) to improve DP’s understanding about how to use the software. DP had to watch the videos before answering the items. To test PERVALE-S, a sample of 56 individuals was recruited (18 signers, 8 lip-readers, and 30 HP). Participants also performed a personality test (High School Personality Questionnaire adapted) and a fluid intelligence (Gf) measure (RAPM). Moreover, all deaf participants were rated by four teachers for the deaf. Results: there were no significant differences between deaf and HP in performance in PERVALE-S. Confusion matrices revealed that embarrassment, envy, and jealousy were worse perceived. Age was just related to social-emotional tasks (but not in basic emotional tasks). Emotional perception ability was related mainly to warmth and consciousness, but negatively related to tension. Meanwhile, Gf was related to only social-emotional tasks. There were no gender differences. PMID:26300828

Residual stresses and mechanical properties of Si3N4/SiC multilayered composites with different SiC layers

International Nuclear Information System (INIS)

Liua, S.; Lia, Y.; Chena, P.; Lia, W.; Gaoa, S.; Zhang, B.; Yeb, F.

2017-01-01

The effect of residual stresses on the strength, toughness and work of fracture of Si3N4/SiC multilayered composites with different SiC layers has been investigated. It may be an effective way to design and optimize the mechanical properties of Si3N4/SiC multilayered composites by controlling the properties of SiC layers. Si3N4/SiC multilayered composites with different SiC layers were fabricated by aqueous tape casting and pressureless sintering. Residual stresses were calculated by using ANSYS simulation, the maximum values of tensile and compressive stresses were 553.2MPa and −552.1MPa, respectively. Step-like fracture was observed from the fracture surfaces. Fraction of delamination layers increased with the residual stress, which can improve the reliability of the materials. Tensile residual stress was benefit to improving toughness and work of fracture, but the strength of the composites decreased. [es

Effects of lysine residues on structural characteristics and stability of tau proteins

Energy Technology Data Exchange (ETDEWEB)

Lee, Myeongsang; Baek, Inchul; Choi, Hyunsung; Kim, Jae In; Na, Sungsoo, E-mail: nass@korea.ac.kr

2015-10-23

Pathological amyloid proteins have been implicated in neuro-degenerative diseases, specifically Alzheimer's, Parkinson's, Lewy-body diseases and prion related diseases. In prion related diseases, functional tau proteins can be transformed into pathological agents by environmental factors, including oxidative stress, inflammation, Aβ-mediated toxicity and covalent modification. These pathological agents are stable under physiological conditions and are not easily degraded. This un-degradable characteristic of tau proteins enables their utilization as functional materials to capturing the carbon dioxides. For the proper utilization of amyloid proteins as functional materials efficiently, a basic study regarding their structural characteristic is necessary. Here, we investigated the basic tau protein structure of wild-type (WT) and tau proteins with lysine residues mutation at glutamic residue (Q2K) on tau protein at atomistic scale. We also reported the size effect of both the WT and Q2K structures, which allowed us to identify the stability of those amyloid structures. - Highlights: • Lysine mutation effect alters the structure conformation and characteristic of tau. • Over the 15 layers both WT and Q2K models, both tau proteins undergo fractions. • Lysine mutation causes the increment of non-bonded energy and solvent accessible surface area. • Structural instability of Q2K model was proved by the number of hydrogen bonds analysis.

Basic freight forwarding and transport
 documentation in freight forwarder’s work

Directory of Open Access Journals (Sweden)

Adam Salomon

2014-09-01

Full Text Available The purpose of the article is to present the basic documentation in international freight forwarder’s work, in particular, insurance documents and transport documents in various modes of transport. An additional goal is to identify sources of the paper, which can be used to properly completing the individual documents.

Effects on residual stresses of aluminum alloy LC4 by laser shock processing

Science.gov (United States)

Zhang, Yong-kang; Lu, Jin-zhong; Kong, De-jun; Yao, Hui-xue; Yang, Chao-jun

2007-12-01

The influences of processing parameters on laser-induced shock waves in metal components are discussed and analyzed. The effects of different parameters of laser shock processing (LSP) on residual stress of aerospace aluminum alloy LC4 were investigated. LSP was performed by using an Nd: glass phosphate laser with 23 ns pulse width and up to ~45 J pulse energy at power densities above GW/mm -2. Special attention is paid to the residual stresses from laser shock processing. Modification of microstructure, surface morphology by laser shock processing is also discussed. Results to date indicate that laser shock processing has great potential as a means of improving the mechanical performance of components.

The 4s24p3-4s4p4 transition in AsI-like AgXV

International Nuclear Information System (INIS)

Dong Chenzhong; Zhao Jinbao

1992-01-01

Some terms of the 4s 4p 4 configuration in RuXII, RhXIII and PdXIV ions can be improved and all the energy values of the configuration in AgXV can be predicted theoretically by means of a configuration-interaction ab initio analysis for the level structure of the 4s 4p 4 configuration along the AsI sequence of KrIV-AgXV ions. Calculations of the wavelengths and oscillator strenghts are presented for the 4s 2 4p 3 -4s 4p 4 transition in AgXV. (orig.)

Assessment of the residual lifetime of the units 3 and 4 of the Kozloduy NPP

International Nuclear Information System (INIS)

Mojkinski, G.

2011-01-01

The purpose of the report is to present the methodology for the residual lifetime assessment for the buildings and facilities during the decommissioning. An analysis of the existing facilities and constructions is made and requirements for further exploitation are set. A quantitative assessment is made of the residual lifetime for the buildings and auxiliary objects for the units 3 and 4. A detailed analysis is made for the ventilation systems and other equipment. Recommendations are given for the extension of the equipment lifetime

Voltage Sensing in Membranes: From Macroscopic Currents to Molecular Motions.

Science.gov (United States)

Freites, J Alfredo; Tobias, Douglas J

2015-06-01

Voltage-sensing domains (VSDs) are integral membrane protein units that sense changes in membrane electric potential, and through the resulting conformational changes, regulate a specific function. VSDs confer voltage-sensitivity to a large superfamily of membrane proteins that includes voltage-gated Na[Formula: see text], K[Formula: see text], Ca[Formula: see text] ,and H[Formula: see text] selective channels, hyperpolarization-activated cyclic nucleotide-gated channels, and voltage-sensing phosphatases. VSDs consist of four transmembrane segments (termed S1 through S4). Their most salient structural feature is the highly conserved positions for charged residues in their sequences. S4 exhibits at least three conserved triplet repeats composed of one basic residue (mostly arginine) followed by two hydrophobic residues. These S4 basic side chains participate in a state-dependent internal salt-bridge network with at least four acidic residues in S1-S3. The signature of voltage-dependent activation in electrophysiology experiments is a transient current (termed gating or sensing current) upon a change in applied membrane potential as the basic side chains in S4 move across the membrane electric field. Thus, the unique structural features of the VSD architecture allow for competing requirements: maintaining a series of stable transmembrane conformations, while allowing charge motion, as briefly reviewed here.

Content Of 2,4-D-14C Herbicide Residue In Water And Soil Of Irrigated Rice Field System

International Nuclear Information System (INIS)

Chairul, Sofnie M.; Djabir, Elida; Magdalena, Nelly

2000-01-01

The investigation of 2,4-D exp.-14C herbicide residue in water and soil of irrigated rice field system was carried out. Rice plant and weeds (Monochoria vaginalis Burn. F. Presl) were planted in 101 buckets using two kinds of soil condition, I.e. normal soil and 30 % above normal compact soil. After one week planting, the plants were sprayed with 1 u Ci of 2,4-D exp.-14C and 0,4 mg non labeled 2,4-D. The herbicide residue content was determined 0, 2, 4, 8 and 10 weeks after spraying with 2,4-D herbicide. The analysis was done using Combustion Biological Oxidizer merk Harvey ox-400, and counted with Liquid Scintillation Counter merk Beckman model LS-1801. The results indicates that the herbicide contents in water and soil decrease from the first spraying with herbicide until harvest herbicide Residue content in water after harvest was 0.87 x 10 exp.-6 ppm for soil normal condition, and 0.59 x 10 exp.-6 pm for the soil 30 % up normal condition, while herbicide content in soil was 1.54 x 10 exp.-6 ppm for soil normal condition and 1.48 x 10 exp.-6 ppm for soil 30 % up normal. 2,4-D herbicide residue content in rice after harvest was 0.27 x 10 exp.-6 ppm for normal soil condition and 0.25 x 10 exp.-6 ppm for the soil 30 % up normal. 2,4-D herbicide residue content in roots and leaves of weeds after harvest were respectively 0.29 x 10 exp.-6 ppm and 0.18 x 10 exp.-6 for normal soil condition, while for 30 % up normal soil were 0.25 x 10 exp.-5 ppm and 0.63 x 10 exp.-7 ppm. This result indicates that there is no effect pollution to surrounding area, because the herbicide content is still bellow the allowed detection limit, 0.05 ppm

International urodynamic basic spinal cord injury data set.

Science.gov (United States)

Biering-Sørensen, F; Craggs, M; Kennelly, M; Schick, E; Wyndaele, J-J

2008-07-01

To create the International Urodynamic Basic Spinal Cord Injury (SCI) Data Set within the framework of the International SCI Data Sets. International working group. The draft of the data set was developed by a working group consisting of members appointed by the Neurourology Committee of the International Continence Society, the European Association of Urology, the American Spinal Injury Association (ASIA), the International Spinal Cord Society (ISCoS) and a representative of the Executive Committee of the International SCI Standards and Data Sets. The final version of the data set was developed after review and comments by members of the Executive Committee of the International SCI Standards and Data Sets, the ISCoS Scientific Committee, ASIA Board, relevant and interested (international) organizations and societies (around 40) and persons and the ISCoS Council. Endorsement of the data set by relevant organizations and societies will be obtained. To make the data set uniform, each variable and each response category within each variable have been specifically defined in a way that is designed to promote the collection and reporting of comparable minimal data. Variables included in the International Urodynamic Basic SCI Data Set are date of data collection, bladder sensation during filling cystometry, detrusor function, compliance during filing cystometry, function during voiding, detrusor leak point pressure, maximum detrusor pressure, cystometric bladder capacity and post-void residual volume.

Residual analysis applied to S-N data of a surface rolled cast iron

Directory of Open Access Journals (Sweden)

Omar Maluf

2005-09-01

Full Text Available Surface rolling is a process extensively employed in the manufacture of ductile cast iron crankshafts, specifically in regions containing stress concentrators with the main aim to enhance fatigue strength. Such process hardens and introduces compressive residual stresses to the surface as a result of controlled strains, reducing cyclic tensile stresses near the surface of the part. The main purpose of this work was to apply the residual analysis to check the suitability of the S-N approach to describe the fatigue properties of a surface rolled cast iron. The analysis procedure proved to be very efficient and easy to implement and it can be applied in the verification of any other statistical model used to describe fatigue behavior. Results show that the conventional S-N methodology is able to model the high cycle fatigue behavior of surface rolled notch testpieces of a pearlitic ductile cast iron submitted to rotating bending fatigue tests.

“Specificity Determinants” Improve Therapeutic Indices of Two Antimicrobial Peptides Piscidin 1 and Dermaseptin S4 Against the Gram-negative Pathogens Acinetobacter baumannii and Pseudomonas aeruginosa

Directory of Open Access Journals (Sweden)

Ziqing Jiang

2014-03-01

Full Text Available A new class of antimicrobial agents with lower rates of resistance and different targets is urgently needed because of the rapidly increasing resistance to classical antibiotics. Amphipathic cationic α-helical antimicrobial peptides (AMPs represent such a class of compounds. In our previous studies, using a 26-residue de novo designed antimicrobial peptide, we proposed the concept of “specificity determinant(s”: positively charged residue(s in the center of the non-polar face of AMPs that could decrease hemolytic activity/toxicity but increase or maintain the same level of antimicrobial activity to increase dramatically the therapeutic index. In the current study, we used d-enantiomers of two AMPs, Piscidin 1 isolated from fish and dermaseptin S4 isolated from frog. We substituted different positions in the center of the hydrophobic face with one or two lysine residue(s (one or two “specificity determinant(s”. This simple modification not only maintained or improved antimicrobial activity against Gram-negative pathogens Acinetobacter baumannii (11 strains and Pseudomonas aeruginosa (6 strains, but also dramatically decreased hemolytic activity of human red blood cells, as predicted. Therapeutic indices improved by 55-fold and 730-fold for piscidin 1 (I9K and dermaseptin S4 (L7K, A14K, respectively, against A. baumannii. Similarly, the therapeutic indices improved 32-fold and 980-fold for piscidin 1 (I9K and dermaseptin S4 (L7K, A14K, respectively, against P. aeruginosa.

Two short basic sequences surrounding the zinc finger of nucleocapsid protein NCp10 of Moloney murine leukemia virus are critical for RNA annealing activity.

Science.gov (United States)

De Rocquigny, H; Ficheux, D; Gabus, C; Allain, B; Fournie-Zaluski, M C; Darlix, J L; Roques, B P

1993-02-25

The 56 amino acid nucleocapsid protein (NCp10) of Moloney Murine Leukemia Virus, contains a CysX2CysX4HisX4Cys zinc finger flanked by basic residues. In vitro NCp10 promotes genomic RNA dimerization, a process most probably linked to genomic RNA packaging, and replication primer tRNA(Pro) annealing to the initiation site of reverse transcription. To characterize the amino-acid sequences involved in the various functions of NCp10, we have synthesized by solid phase method the native protein and a series of derived peptides shortened at the N- or C-terminus with or without the zinc finger domain. In the latter case, the two parts of the protein were linked by a Glycine - Glycine spacer. The in vitro studies of these peptides show that nucleic acid annealing activities of NCp10 do not require a zinc finger but are critically dependent on the presence of specific sequences located on each side of the CCHC domain and containing proline and basic residues. Thus, deletion of 11R or 49PRPQT, of the fully active 29 residue peptide 11RQGGERRRSQLDRDGGKKPRGPRGPRPQT53 leads to a complete loss of NCp10 activity. Therefore it is proposed that in NCp10, the zinc finger directs the spatial recognition of the target RNAs by the basic domains surrounding the zinc finger.

Design of a process for the use of residual hydrocarbons coming from the ships arriving at Moin for obtaining of a fuel

International Nuclear Information System (INIS)

Madrigal Calderon, Adolfo

2015-01-01

A process is designed to carry out the obtaining of a fuel from the residual mixture of residual oils coming from the ships arriving at Moin, Limon, Costa Rica . A sampling of the residual oil in different ships is realized for a month to quantify the water content and basic sediment, as well as the heavy metal content. The results obtained have been 20,4 ± 4,6 % v/v of water and sediment, and 6,939 ppm of heavy metals as a minimum, this value may be higher depending on the quality of lubricant. The production volume of the residual oil is estimated according to historical data of the company ACASE S.A. (company responsible for collecting the oil residue of ships arriving at dock of Moin, Limon); therefore, the plant must process 25,000 liters of dirty oil per day. The main technologies (thermal process, treatment with chemical reaction, vacuum distillation and solvent extraction) to perform the process are compared and studied through a selection matrix. The technical and economic parameters chosen for the matrix have been: environmental impact, cost of operation, cost of equipment, safety of operation, maintenance of equipment, by-products obtained, waste generated, quality of the product obtained and ease of operation. The study has concluded that the treatment with chemical reaction has been the best option for the project of used oil utilization, as well as other physical methods of cleaning as the centrifugation of the same one. The installation of a waste oil processing plant has been a project that environmentally represents a benefit and economically viable, as currently the residual oil is left untreated for later use [es

Martensitic transformation and residual stresses after thermomechanical treatment of heat treatable steel 42CrMo4 (SAE 4140)

Energy Technology Data Exchange (ETDEWEB)

Weise, A. [Technische Univ. Chemnitz-Zwickau, Chemnitz (Germany). Fakultaet fuer Maschinenbau und Verfahrenstechnik; Fritsche, G. [Technische Univ. Chemnitz-Zwickau, Chemnitz (Germany). Fakultaet fuer Maschinenbau und Verfahrenstechnik

1996-01-01

The influence of thermomechanical deformation on the residual stresses caused by quenching in bar shaped specimens of heat treatable steel 42CrMo4 has been investigated using a mechanical method for determining the distribution of residual stresses of the first kind. The results obtained show that the residual stress distribution after quenching is affected by the strengthening and softening of the austenite as a result of deformation and recrystallization and the modified transformation behaviour in martensite stage. An attempt is made to discuss qualitatively the influence of these changes on the generation of residual stresses as compared to results obtained after conventional hardening. (orig.).

Martensitic transformation and residual stresses after thermomechanical treatment of heat treatable steel 42CrMo4 (SAE 4140)

International Nuclear Information System (INIS)

Weise, A.; Fritsche, G.

1996-01-01

The influence of thermomechanical deformation on the residual stresses caused by quenching in bar shaped specimens of heat treatable steel 42CrMo4 has been investigated using a mechanical method for determining the distribution of residual stresses of the first kind. The results obtained show that the residual stress distribution after quenching is affected by the strengthening and softening of the austenite as a result of deformation and recrystallization and the modified transformation behaviour in martensite stage. An attempt is made to discuss qualitatively the influence of these changes on the generation of residual stresses as compared to results obtained after conventional hardening. (orig.)

Phactr3/scapinin, a member of protein phosphatase 1 and actin regulator (phactr family, interacts with the plasma membrane via basic and hydrophobic residues in the N-terminus.

Directory of Open Access Journals (Sweden)

Akihiro Itoh

Full Text Available Proteins that belong to the protein phosphatase 1 and actin regulator (phactr family are involved in cell motility and morphogenesis. However, the mechanisms that regulate the actin cytoskeleton are poorly understood. We have previously shown that phactr3, also known as scapinin, localizes to the plasma membrane, including lamellipodia and membrane ruffles. In the present study, experiments using deletion and point mutants showed that the basic and hydrophobic residues in the N-terminus play crucial roles in the localization to the plasma membrane. A BH analysis (http://helixweb.nih.gov/bhsearch is a program developed to identify membrane-binding domains that comprise basic and hydrophobic residues in membrane proteins. We applied this program to phactr3. The results of the BH plot analysis agreed with the experimentally determined region that is responsible for the localization of phactr3 to the plasma membrane. In vitro experiments showed that the N-terminal itself binds to liposomes and acidic phospholipids. In addition, we showed that the interaction with the plasma membrane via the N-terminal membrane-binding sequence is required for phactr3-induced morphological changes in Cos7 cells. The membrane-binding sequence in the N-terminus is highly conserved in all members of the phactr family. Our findings may provide a molecular basis for understanding the mechanisms that allow phactr proteins to regulate cell morphogenesis.

A study of the influence of charged residues on β-hairpin formation by nuclear magnetic resonance and molecular dynamics.

Science.gov (United States)

Makowska, Joanna; Zmudzińska, Wioletta; Uber, Dorota; Chmurzyński, Lech

2014-12-01

Chain reversals are often nucleation sites in protein folding. The β-hairpins of FBP28 WW domain and IgG are stable and have been proved to initiate the folding and are, therefore, suitable for studying the influence of charged residues on β-hairpin conformation. In this paper, we carried out NMR examination of the conformations in solution of two fragments from the FPB28 protein (PDB code: 1E0L) (N-terminal part) namely KTADGKT-NH2 (1E0L 12-18, D7) and YKTADGKTY-NH2 (1E0L 11-19, D9), one from the B3 domain of the protein G (PDB code: 1IGD), namely DDATKT-NH2 (1IGD 51-56) (Dag1), and three variants of Dag1 peptide: DVATKT-NH2 (Dag2), OVATKT-NH2 (Dag3) and KVATKT-NH2 (Dag4), respectively, in which the original charged residue were replaced with non-polar residues or modified charged residues. It was found that both the D7 and D9 peptides form a large fraction bent conformations. However, no hydrophobic contacts between the terminal Tyr residues of D9 occur, which suggests that the presence of a pair of like-charged residues stabilizes chain reversal. Conversely, only the Dag1 and Dag2 peptides exhibit some chain reversal; replacing the second aspartic-acid residue with a valine and the first one with a basic residue results in a nearly extended conformation. These results suggest that basic residues farther away in sequence can result in stabilization of chain reversal owing to screening of the non-polar core. Conversely, smaller distance in sequence prohibits this screening, while the presence oppositely-charged residues can stabilize a turn because of salt-bridge formation.

S100A4: a common mediator of epithelial-mesenchymal transition, fibrosis and regeneration in diseases?

DEFF Research Database (Denmark)

Schneider, M.; Sheikh, S.P.; Hansen, Jakob Lerche

2008-01-01

and neuronal injuries. Common to all these diseases is the involvement of fibrotic and inflammatory processes, i.e. processes greatly dependent on tissue remodelling, cell motility and epithelial-mesenchymal transition. Therefore, the basic biological mechanisms behind S100A4's effects are emerging. S100A4...... belongs to the S100 family of proteins that contain two Ca2+-binding sites including a canonical EF-hand motif. S100A4 is involved in the regulation of a wide range of biological effects including cell motility, survival, differentiation and contractility. S100A4 has both intracellular and extracellular...... effects. Hence, S100A4 interacts with cytoskeletal proteins and enhances metastasis of several types of cancer cells. In addition, S100A4 is secreted by unknown mechanisms, thus, paracrinely stimulating a variety of cellular responses, including angiogenesis and neuronal growth. Although many cellular...

Monitoring and Auditing Residual Information on the User’s Computer

Directory of Open Access Journals (Sweden)

Vladlena Sergeevna Oladk

2015-06-01

Full Text Available This paper considers the problem of violation of information security components such as confidentiality and availability in the event of a computer user's residual information. Analyze the requirements of regulators and mechanisms to be applied in the organization to monitor the residual information or its destruction.Approach to monitoring and auditing residual information on the user's computer, which allows monitoring the residual information in certain areas proposed. Approach allows us to identify the detected information and rank it according to the degree of criticality, as well as calculate the risk of leakage and its potential to develop recommendations aimed at its reduction. The proposed approach is formally described and automated in a software system.

Experimental investigation of impulse response shortening for low-complexity MLSE of a 112-Gbit/s PAM-4 transceiver

NARCIS (Netherlands)

van der Heide, S.; Eiselt, N.; Griesser, H.; Olmos, J. J.V.; Tafur Monroy, I.; Okonkwo, C.

2016-01-01

An optimized channel shortening method for reduced complexity MLSE detection enables the compensation of severe inter-symbol interference. Experimental investigations demonstrate the benefit on the performance for a severely bandwidth limited 112-Gbit/s PAM-4 transmission system with residual

Experimental investigation of impulse response shortening for low-complexity MLSE of a 112-Gbit/s PAM-4 transceiver

DEFF Research Database (Denmark)

Van Der Heide, Sjoerd; Eiselt, Nicklas; Griesser, Helmut

2016-01-01

An optimized channel shortening method for reduced complexity MLSE detection enables the compensation of severe inter-symbol interference. Experimental investigations demonstrate the benefit on the performance for a severely bandwidth limited 112-Gbit/s PAM-4 transmission system with residual chr...

Site-directed Mutagenesis of Cysteine Residues in Phi-class Glutathione S-transferase F3 from Oryza sativa

Energy Technology Data Exchange (ETDEWEB)

Jo, Hyunjoo; Lee, Juwon; Noh, Jinseok; Kong, Kwanghoon [Chung-Ang Univ., Seoul (Korea, Republic of)

2012-12-15

To elucidate the roles of cysteine residues in rice Phi-class GST F3, in this study, all three cysteine residues were replaced with alanine by site-directed mutagenesis in order to obtain mutants C22A, C73A and C77A. Three mutant enzymes were expressed in Escherichia coli and purified to electrophoretic homogeneity by affinity chromatography on immobilized GSH. The substitutions of Cys73 and Cys77 residues in OsGSTF3 with alanine did not affect the glutathione conjugation activities, showing non-essentiality of these residues. On the other hand, the substitution of Cys22 residue with alanine resulted in approximately a 60% loss of specific activity toward ethacrynic acid. Moreover, the K{sub m}{sup CDNB} value of the mutant C22A was approximately 2.2 fold larger than that of the wild type. From these results, the evolutionally conserved cysteine 22 residue seems to participate rather in the structural stability of the active site in OsGSTF3 by stabilizing the electrophilic substrates-binding site's conformation than in the substrate binding directly.

Supersymmetric extension of Hopf maps: N = 4 {sigma}-models and the S{sup 3} {yields} S{sup 2} fibration

Energy Technology Data Exchange (ETDEWEB)

Carvalho, L. Faria; Toppan, F., E-mail: leofc@cbpf.b, E-mail: toppan@cbpf.b [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil); Kuznetsova, Z., E-mail: zhanna.kuznetsova@ufabc.edu.b [Universidade Federal do ABC (UFABC), Santo Andre, SP (Brazil)

2009-07-01

We discuss four off-shell N = 4 D = 1 supersymmetry transformations, their associated one-dimensional -models and their mutual relations. They are given by I - the (4, 4){sub lin} linear 'root' supermultiplet (supersymmetric extension of R{sup 4}), II - the (3, 4, 1){sub lin} linear supermultiplet (supersymmetric extension of R3), III - the (3, 4, 1){sub nl} non-linear supermultiplet living on S{sup 3} and IV - the (2, 4, 2){sub nl} non-linear supermultiplet living on S{sup 2}. The I {yields} II map is the supersymmetric extension of the R4 {yields} R3 bilinear map, while the II {yields} IV map is the supersymmetric extension of the S{sup 3} {yields} S{sup 2} first Hopf fibration. The restrictions on the S{sup 3}, S{sup 2} spheres are expressed in terms of the stereo graphic projections. The non-linear supermultiplets, whose super transformations are local differential polynomials, are not equivalent to the linear supermultiplets with the same field content. The -models are determined in terms of an unconstrained pre potential of the target coordinates. The Uniformization Problem requires solving an inverse problem for the pre potential. The basic features of the supersymmetric extension of the second and third Hopf maps are briefly sketched. Finally, the Schur's lemma (i.e. the real, complex or quaternionic property) is extended to all minimal linear supermultiplets up to N {<=} 8. (author)

Molecular interactions and residues involved in force generation in the T4 viral DNA packaging motor.

Science.gov (United States)

Migliori, Amy D; Smith, Douglas E; Arya, Gaurav

2014-12-12

Many viruses utilize molecular motors to package their genomes into preformed capsids. A striking feature of these motors is their ability to generate large forces to drive DNA translocation against entropic, electrostatic, and bending forces resisting DNA confinement. A model based on recently resolved structures of the bacteriophage T4 motor protein gp17 suggests that this motor generates large forces by undergoing a conformational change from an extended to a compact state. This transition is proposed to be driven by electrostatic interactions between complementarily charged residues across the interface between the N- and C-terminal domains of gp17. Here we use atomistic molecular dynamics simulations to investigate in detail the molecular interactions and residues involved in such a compaction transition of gp17. We find that although electrostatic interactions between charged residues contribute significantly to the overall free energy change of compaction, interactions mediated by the uncharged residues are equally if not more important. We identify five charged residues and six uncharged residues at the interface that play a dominant role in the compaction transition and also reveal salt bridging, van der Waals, and solvent hydrogen-bonding interactions mediated by these residues in stabilizing the compact form of gp17. The formation of a salt bridge between Glu309 and Arg494 is found to be particularly crucial, consistent with experiments showing complete abrogation in packaging upon Glu309Lys mutation. The computed contributions of several other residues are also found to correlate well with single-molecule measurements of impairments in DNA translocation activity caused by site-directed mutations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Measurements of three dimensional residual stress distribution on laser irradiated spot

International Nuclear Information System (INIS)

Tanaka, Hirotomo; Akita, Koichi; Ohya, Shin-ichi; Sano, Yuji; Naito, Hideki

2004-01-01

Three dimensional residual stress distributions on laser irradiated spots were measured using synchrotron radiation to study the basic mechanism of laser peening. A water-immersed sample of high tensile strength steel was irradiated with Q-switched and frequency-doubled Nd:YAG laser. The residual stress depth profile of the sample was obtained by alternately repeating the measurement and surface layer removal by electrolytic polishing. Tensile residual stresses were observed on the surface of all irradiated spots, whereas residual stress changed to compressive just beneath the surface. The depth of compressive residual stress imparted by laser irradiation and plastic deformation zone increased with increasing the number of laser pulses irradiated on the same spot. (author)

The potential for energy production from crop residues in Zimbabwe

Energy Technology Data Exchange (ETDEWEB)

Jingura, R.M.; Matengaifa, R. [School of Engineering Sciences and Technology, Chinhoyi University of Technology, P. Bag 7724, Chinhoyi (Zimbabwe)

2008-12-15

There is increasing interest in Zimbabwe in the use of renewable energy sources as a means of meeting the country's energy requirements. Biomass provides 47% of the gross energy consumption in Zimbabwe. Energy can be derived from various forms of biomass using various available conversion technologies. Crop residues constitute a large part of the biomass available from the country's agriculture-based economy. The potential for energy production of crop residues is examined using data such as estimates of the quantities of the residues and their energy content. The major crops considered are maize, sugarcane, cotton, soyabeans, groundnuts, wheat, sorghum, fruits and forestry plantations. Quantities of residues are estimated from crop yields by using conversion coefficients for the various crops. Long-term crop yields data from 1970 to 1999 were used. Total annual residue yields for crops, fruits and forestry plantations are 7.805 Mt, 378 kt and 3.05 Mt, respectively. The crops, fruits and forestry residues have energy potential of 81.5, 4.9 and 44.3 PJ per year, respectively. This represents about 44% of the gross energy consumption in Zimbabwe. The need to balance use of crop residues for both energy purposes and other purposes such as animal feeding and soil fertility improvement is also highlighted. (author)

Rethinking Teaching of Basic Principles of Economics from a Sustainability Perspective

Directory of Open Access Journals (Sweden)

Namrata Chindarkar

2018-05-01

Full Text Available In this paper, we posit that sustainability warrants explicit recognition in the teaching of basic principles of economics. The conventional exposition of conceptual and analytic frameworks in basic principles in almost all standard economics textbooks overlooks at least two basic flaws. The first of these concerns the collection of residual externalities that exist without being internalized in market transactions and hence fall outside the calculus of national income accounting. For example, not all energy resource prices capture the entirety of the damages inflicted on natural ecosystems. The cumulus of residual externalities threatens the feasibility of sustainability. The second flaw is the absence of sustainability as a necessary condition in the fundamental benchmark of perfect competition (PC. Sustainability, when explicitly introduced in the PC benchmark, results in significant changes to conceptual premises in economics. The most significant of such changes concerns the axiomatic differentiation between “goods” and “bads”.

Thermal lattice benchmarks for testing basic evaluated data files, developed with MCNP4B

International Nuclear Information System (INIS)

Maucec, M.; Glumac, B.

1996-01-01

The development of unit cell and full reactor core models of DIMPLE S01A and TRX-1 and TRX-2 benchmark experiments, using Monte Carlo computer code MCNP4B is presented. Nuclear data from ENDF/B-V and VI version of cross-section library were used in the calculations. In addition, a comparison to results obtained with the similar models and cross-section data from the EJ2-MCNPlib library (which is based upon the JEF-2.2 evaluation) developed in IRC Petten, Netherlands is presented. The results of the criticality calculation with ENDF/B-VI data library, and a comparison to results obtained using JEF-2.2 evaluation, confirm the MCNP4B full core model of a DIMPLE reactor as a good benchmark for testing basic evaluated data files. On the other hand, the criticality calculations results obtained using the TRX full core models show less agreement with experiment. It is obvious that without additional data about the TRX geometry, our TRX models are not suitable as Monte Carlo benchmarks. (author)

Effects of LSP on micro-structures and residual stresses in a 4 mm CLAM steel weld joints

Energy Technology Data Exchange (ETDEWEB)

Chen, Xizhang, E-mail: chenxizhang@wzu.edu.cn [School of Mechanical and Electrical Engineering, Wenzhou University., Wenzhou 325035 (China); School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Fang, Yuanyuan [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Zhang, Shuyan; Kelleher, Joe F. [ISIS, Rutherford Appleton Laboratory, Chilton, Didcot OX11 0QX (United Kingdom); Zhou, Jianzhong [School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China)

2015-05-15

The effects of laser shock processing (LSP) on the distribution of residual stress and micro-structure of China Low Activation Martensitic (CLAM) steel weldment were investigated via neutron diffraction and optical microscope (OM). A pair of 4 mm CLAM steel plates joined by GTA welding. Special attention is paid to the generation of high level compressive residual stresses introduced by LSP. Residual stress in longitudinal, normal and transversal direction at weldment surface and longitudinal stress through thickness are evaluated via neutron diffraction. Compressive residual stress after LSP occurred at more than 90% areas within the weld joint, it is almost double the areas of compressive stress compare to weldment surface before LSP. The maximum compressive normal residual stress becomes to −183 MPa after LSP from −63 MPa before LSP. The Modification of surface micro-structures including weld zone (WZ), heat affected zone (HAZ) and base metal (BM) are also discussed. Results to date demonstrate that laser shock processing has been a great potential method for the improvement of mechanical performance of components.

Structure-Activity Relationship in TLR4 Mutations: Atomistic Molecular Dynamics Simulations and Residue Interaction Network Analysis

Science.gov (United States)

Anwar, Muhammad Ayaz; Choi, Sangdun

2017-03-01

Toll-like receptor 4 (TLR4), a vital innate immune receptor present on cell surfaces, initiates a signaling cascade during danger and bacterial intrusion. TLR4 needs to form a stable hexamer complex, which is necessary to dimerize the cytoplasmic domain. However, D299G and T399I polymorphism may abrogate the stability of the complex, leading to compromised TLR4 signaling. Crystallography provides valuable insights into the structural aspects of the TLR4 ectodomain; however, the dynamic behavior of polymorphic TLR4 is still unclear. Here, we employed molecular dynamics simulations (MDS), as well as principal component and residue network analyses, to decipher the structural aspects and signaling propagation associated with mutations in TLR4. The mutated complexes were less cohesive, displayed local and global variation in the secondary structure, and anomalous decay in rotational correlation function. Principal component analysis indicated that the mutated complexes also exhibited distinct low-frequency motions, which may be correlated to the differential behaviors of these TLR4 variants. Moreover, residue interaction networks (RIN) revealed that the mutated TLR4/myeloid differentiation factor (MD) 2 complex may perpetuate abnormal signaling pathways. Cumulatively, the MDS and RIN analyses elucidated the mutant-specific conformational alterations, which may help in deciphering the mechanism of loss-of-function mutations.

Overlapping Residual Herbicides for Control of Photosystem (PS) II- and 4-Hydroxyphenylpyruvate Dioxygenase (HPPD)-Inhibitor-Resistant Palmer amaranth (Amaranthus palmeri S. Watson) in Glyphosate-Resistant Maize

Science.gov (United States)

Chahal, Parminder S.; Ganie, Zahoor A.; Jhala, Amit J.

2018-01-01

A Palmer amaranth (Amaranthus palmeri S. Watson) biotype has evolved resistance to photosystem (PS) II- (atrazine) and 4-hydroxyphenylpyruvate dioxygenase (HPPD)-inhibiting herbicides (mesotrione, tembotrione, and topramezone) in maize seed production field in Nebraska, USA. The objectives of this study were to determine the effect of soil residual pre-emergence (PRE) herbicides followed by (fb) tank-mixture of residual and foliar active post-emergence (POST) herbicides on PS-II- and HPPD-inhibitor-resistant Palmer amaranth control, maize yield, and net economic returns. Field experiments were conducted in a grower's field infested with PS II- and HPPD-inhibitor-resistant Palmer amaranth near Shickley in Fillmore County, Nebraska, USA in 2015 and 2016. The contrast analysis suggested that saflufenacil plus dimethenamid-P or pyroxasulfone plus saflufenacil applied PRE provided 80–82% Palmer amaranth control compared to 65 and 39% control with saflufenacil and pyroxasulfone applied alone at 3 weeks after PRE (WAPRE), respectively. Among the PRE fb POST herbicide programs, 95–98% Palmer amaranth control was achieved with pyroxasulfone plus safluefenacil, or saflufenacil plus dimethenamid-P applied PRE, fb glyphosate plus topramezone plus dimethenamid-P plus atrazine, glyphosate plus diflufenzopyr plus dicamba plus pyroxasulfone, glyphosate plus diflufenzopyr plus pendimethalin, or glyphosate plus diflufenzopyr plus dicamba plus atrazine applied POST at 3 weeks after POST (WAPOST) through maize harvest. Based on contrast analysis, PRE fb POST programs provided 77–83% Palmer amaranth control at 3 WAPOST through maize harvest compared to 12–15% control with PRE-only and 66–84% control with POST-only programs. Similarly, PRE fb POST programs provided 99% biomass reduction at 6 WAPOST compared to PRE-only (28%) and POST-only (87%) programs. PRE fb POST programs provided higher maize yield (13,617 kg ha−1) and net return (US $1,724 ha−1) compared to the PRE

Analysis of Amino Acid Residues of Potential Importance for Phosphati-dylserine Specificity of P4-type ATPase ATP8A2

DEFF Research Database (Denmark)

Mogensen, Louise; Vestergaard, Anna Lindeløv; Mikkelsen, Stine

The asymmetric structure of the plasma membrane is maintained through internalization of phos-pholipids by the family of P4-ATPases by a poorly characterized mechanism. Studies in yeast point towards a non-classical pathway involving important residues of a two-gate mechanism [1]. Glycine-230...... 302 of ATP8A2 with alanine (N302A), tyrosine (N302Y) and serine (N302S). Furthermore, a triple mutant of ATP8A2 (Q95GQ96AN302S) was studied to reveal any cooperativity between the two gates, as observed in yeast [1]. The affinities of the mutants for phosphatidylserine and phosphatidylethanolamine...

Mutations at the S1 sites of methionine aminopeptidases from Escherichia coli and Homo sapiens reveal the residues critical for substrate specificity.

Science.gov (United States)

Li, Jing-Ya; Cui, Yong-Mei; Chen, Ling-Ling; Gu, Min; Li, Jia; Nan, Fa-Jun; Ye, Qi-Zhuang

2004-05-14

Methionine aminopeptidase (MetAP) catalyzes the removal of methionine from newly synthesized polypeptides. MetAP carries out this cleavage with high precision, and Met is the only natural amino acid residue at the N terminus that is accepted, although type I and type II MetAPs use two different sets of residues to form the hydrophobic S1 site. Characteristics of the S1 binding pocket in type I MetAP were investigated by systematic mutation of each of the seven S1 residues in Escherichia coli MetAP type I (EcMetAP1) and human MetAP type I (HsMetAP1). We found that Tyr-65 and Trp-221 in EcMetAP1, as well as the corresponding residues Phe-197 and Trp-352 in HsMetAP1, were essential for the hydrolysis of a thiopeptolide substrate, Met-S-Gly-Phe. Mutation of Phe-191 to Ala in HsMetAP1 caused inactivity in contrast to the full activity of EcMetAP1(Y62A), which may suggest a subtle difference between the two type I enzymes. The more striking finding is that mutation of Cys-70 in EcMetAP1 or Cys-202 in HsMetAP1 opens up the S1 pocket. The thiopeptolides Leu-S-Gly-Phe and Phe-S-Gly-Phe, with previously unacceptable Leu or Phe as the N-terminal residue, became efficient substrates of EcMetAP1(C70A) and HsMetAP1(C202A). The relaxed specificity shown in these S1 site mutants for the N-terminal residues was confirmed by hydrolysis of peptide substrates and inhibition by reaction products. The structural features at the enzyme active site will be useful information for designing specific MetAP inhibitors for therapeutic applications.

Thermophysical properties of Na2Th (MoO4)3 (s) and Na4Th (MoO4)4 (s)

International Nuclear Information System (INIS)

Dash, Smruti; Rakshit, S.K.; Singh, Ziley; Keskar, Meera; Dahale, N.D.

2009-01-01

The heat capacity of Na 2 Th (MoO 4 ) 3 (s) and Na 4 Th (MoO 4 ) 4 (s) have been measured by differential scanning calorimeter in the temperature range 318 to 845 K. The corresponding values are: C p,m (Na 2 Th (MoO 4 ) 3 ,s,T) (JK-1 mol-1) 368.710+ 1.0 10-1 (T/K) - 4950267 (K/T)2 (318 ≤ T (K) ≤ 845). C p,m (Na 4 Th (MoO 4 ) 4 ,s,T) (JK-1 mol-1) = 638.761+ 5.12 10-3 (T/K) - 12691691 (K/T)-2 (318 ≤ T (K) ≤ 845). Experimental heat capacity values for Na 2 Th (MoO 4 ) 3 (s) match reasonably well with that of additive oxide values. But C p,m (T) values of Na 4 Th (MoO 4 ) 4 (s) deviates substantially from the additive oxide values above 700 K. The uncertainty of the measurements reported in this study is calculated to be within 1 to 3 % . (author)

Residual Stresses and Other Properties of Teardrops

Energy Technology Data Exchange (ETDEWEB)

Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hill, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rios, Daniel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Duque, Juan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-07-26

The Department of Energy’s 3013 Standard for packaging plutonium-bearing materials for storage up to fifty years specifies a minimum of two individually welded, nested containers herein referred to as the 3013 outer and the 3013 inner.1 Stress corrosion cracking (SCC) is a potential failure mechanism for 3013 inner containers.2,3 The bagless transfer container (BTC), a 3013 inner container used by Hanford and Savanna River Site (SRS) made from 304L stainless steel (SS), poses the greatest concern for SCC.4,5 The Surveillance and Monitoring Program (SMP) use stressed metal samples known as teardrops as screening tools in SCC studies to evaluate factors that could result in cracks in the 3013 containers.6,7 This report provides background information on the teardrops used in the Los Alamos National Laboratory (LANL) SMP studies including method of construction, composition and variability. In addition, the report discusses measurements of residual stresses in teardrops and compares the results with residual stresses in BTCs reported previously.4 Factors affecting residual stresses, including teardrop dimensions and surface finish, are also discussed.

Development of residual stress prediction model in pipe weldment

Energy Technology Data Exchange (ETDEWEB)

Eom, Yun Yong; Lim, Se Young; Choi, Kang Hyeuk; Cho, Young Sam; Lim, Jae Hyuk [Korea Advanced Institute of Science and Technology, Taejon (Korea, Republic of)

2002-03-15

When Leak Before Break(LBB) concepts is applied to high energy piping of nuclear power plants, residual weld stresses is a important variable. The main purpose of his research is to develop the numerical model which can predict residual weld stresses. Firstly, basic theories were described which need to numerical analysis of welding parts. Before the analysis of pipe, welding of a flat plate was analyzed and compared. Appling the data of used pipes, thermal/mechanical analysis were accomplished and computed temperature gradient and residual stress distribution. For thermal analysis, proper heat flux was regarded as the heat source and convection/radiation heat transfer were considered at surfaces. The residual stresses were counted from the computed temperature gradient and they were compared and verified with a result of another research.

Factors Influencing Dislodgeable 2, 4-D Plant Residues from Hybrid Bermudagrass (Cynodon dactylon L. x C. transvaalensis) Athletic Fields.

Science.gov (United States)

Jeffries, Matthew D; Gannon, Travis W; Brosnan, James T; Ahmed, Khalied A; Breeden, Gregory K

2016-01-01

Research to date has confirmed 2,4-D residues may dislodge from turfgrass; however, experiments have not been conducted on hybrid bermudagrass (Cynodon dactylon L. x C. transvaalensis), the most common athletic field turfgrass in subtropical climates. More specifically, previous research has not investigated the effect of post-application irrigation on dislodgeable 2,4-D residues from hybrid bermudagrass and across turfgrass species, research has been nondescript regarding sample time within a d (TWD) or conducted in the afternoon when the turfgrass canopy is dry, possibly underestimating potential for dislodgement. The effect of irrigation and TWD on 2,4-D dislodgeability was investigated. Dislodgeable 2,4-D amine was reduced > 300% following irrigation. From 2 to 7 d after treatment (DAT), ≤ 0.5% of applied 2,4-D was dislodged from irrigated turfgrass, while ≤ 2.3% of applied 2,4-D was dislodged when not irrigated. 2,4-D dislodgeability decreased as TWD increased. Dislodgeable 2,4-D residues declined to < 0.1% of the applied at 1 DAT- 13:00, and increased to 1 to 3% of the applied 2 DAT- 5:00, suggesting 2,4-D re-suspended on treated turfgrass vegetation overnight. In conclusion, irrigating treated turfgrass reduced dislodgeable 2,4-D. 2,4-D dislodgeability increased as TWD decreased, which was attributed to non-precipitation climatic conditions favoring turfgrass canopy wetness. This research will improve turfgrass management practices and research designed to minimize human 2,4-D exposure.

Discontinuity relations for the AdS{sub 4}/CFT{sub 3} correspondence

Energy Technology Data Exchange (ETDEWEB)

Cavaglià, Andrea, E-mail: Cavaglia@to.infn.it [Centre for Mathematical Science, City University London, Northampton Square, London EC1V 0HB (United Kingdom); Dipartimento di Fisica and INFN, Università di Torino, Via P. Giuria 1, 10125 Torino (Italy); Fioravanti, Davide, E-mail: Fioravanti@bo.infn.it [INFN-Bologna and Dipartimento di Fisica e Astronomia, Università di Bologna, Via Irnerio 46, 40126 Bologna (Italy); Tateo, Roberto, E-mail: Tateo@to.infn.it [Dipartimento di Fisica and INFN, Università di Torino, Via P. Giuria 1, 10125 Torino (Italy)

2013-12-21

We study in detail the analytic properties of the Thermodynamic Bethe Ansatz (TBA) equations for the anomalous dimensions of composite operators in the planar limit of the 3D N=6 superconformal Chern–Simons gauge theory and derive functional relations for the jump discontinuities across the branch cuts in the complex rapidity plane. These relations encode the analytic structure of the Y functions and are extremely similar to the ones obtained for the previously-studied AdS{sub 5}/CFT{sub 4} case. Together with the Y-system and more basic analyticity conditions, they are completely equivalent to the TBA equations. We expect these results to be useful to derive alternative nonlinear integral equations for the AdS{sub 4}/CFT{sub 3} spectrum.

Leptogenesis and residual CP symmetry

International Nuclear Information System (INIS)

Chen, Peng; Ding, Gui-Jun; King, Stephen F.

2016-01-01

We discuss flavour dependent leptogenesis in the framework of lepton flavour models based on discrete flavour and CP symmetries applied to the type-I seesaw model. Working in the flavour basis, we analyse the case of two general residual CP symmetries in the neutrino sector, which corresponds to all possible semi-direct models based on a preserved Z 2 in the neutrino sector, together with a CP symmetry, which constrains the PMNS matrix up to a single free parameter which may be fixed by the reactor angle. We systematically study and classify this case for all possible residual CP symmetries, and show that the R-matrix is tightly constrained up to a single free parameter, with only certain forms being consistent with successful leptogenesis, leading to possible connections between leptogenesis and PMNS parameters. The formalism is completely general in the sense that the two residual CP symmetries could result from any high energy discrete flavour theory which respects any CP symmetry. As a simple example, we apply the formalism to a high energy S 4 flavour symmetry with a generalized CP symmetry, broken to two residual CP symmetries in the neutrino sector, recovering familiar results for PMNS predictions, together with new results for flavour dependent leptogenesis.

The Management of Social Phobia Ýn Residual-Type Schizophrenia with Cognitive Behavioral Therapy

Directory of Open Access Journals (Sweden)

Elif Þimþek Kaygusuz

2015-04-01

Full Text Available Having negative symptoms is the basic feature of residual-type schizophrenia and there is a direct proportion between the neurocognitive impairments associated with negative symptoms. Among the approaches used for the treatment of patients with schizophrenia, cognitive behaviour therapy is the one with the most evidence of efficacy. Cognitive behaviour therapy is considered to be beneficial for the residual symptoms after drug treatment. The social phobia leads among the anxiety disorders accompanying schizophrenia. According to the cognitive model, the impairment of social performance increases the severity of social phobia. The leading factor of this vicious circle is that the patients pay attention selectively to such cases in order to find evidence for their thoughts and beliefs that they are going to be evaluated negatively. In this paper, the cognitive behavioural therapy and formulation carried out with a patient, who has been followed for a long time with the diagnosis of residual-type schizophrenia and social phobia is reported. The purpose of the treatment is to interfere with the impaired functionality of the patient through cognitive and behavioural techniques by dealing with the medical treatment-resistant symptoms. To this end, firstly coping mechanisms are examined through the identification of avoidance and security providers, and then, the patient’s automatic thoughts and false beliefs are discussed depending on the cognitive perspective. The main part of the treatment has been completed by carrying out various investigations in order to increase the patients’ social performance via applying behavioural techniques. As a result, false beliefs are the indicators of the relationship between cognitive inability and negative symptoms and related to social functioning. By addressing these beliefs through cognitive behavioural therapy, the necessity of increasing the patient’s social activities and the relationship between social

Investigation of the structural preference and flexibility of the loop residues in amyloid fibrils of the HET-s prion.

Science.gov (United States)

Dolenc, Jožica; Meier, Beat H; Rusu, Victor H; van Gunsteren, Wilfred F

2016-02-17

The structural variability of a 16-residue loop (residues 246-261) which is in part disordered and connects two layers of the β-solenoid formed by the prion-form of HET-s and its prion domain HET-s(218-289) is investigated using molecular dynamics computer simulation. A system of three HET-s(218-289) molecules in a β-sheet structure as in the fibril is simulated in aqueous solution. The trajectory structures appear to be consistent with the Cα chemical shift data obtained. In order to delineate the influence of the β-sheet core of the fibril upon the structural variability of the loop, the latter is also simulated without the β-sheet core, but with its N- and C-terminal residues restrained at their positions in the fibril. The analysis of the trajectories shows that the structural variability of the loop is restricted by the β-sheet core, least at its N-terminal end and most in the middle of the trimer.

H9N2 influenza virus acquires intravenous pathogenicity on the introduction of a pair of di-basic amino acid residues at the cleavage site of the hemagglutinin and consecutive passages in chickens

Directory of Open Access Journals (Sweden)

Sakoda Yoshihiro

2011-02-01

Full Text Available Abstract Background Outbreaks of avian influenza (AI caused by infection with low pathogenic H9N2 viruses have occurred in poultry, resulting in serious economic losses in Asia and the Middle East. It has been difficult to eradicate the H9N2 virus because of its low pathogenicity, frequently causing in apparent infection. It is important for the control of AI to assess whether the H9N2 virus acquires pathogenicity as H5 and H7 viruses. In the present study, we investigated whether a non-pathogenic H9N2 virus, A/chicken/Yokohama/aq-55/2001 (Y55 (H9N2, acquires pathogenicity in chickens when a pair of di-basic amino acid residues is introduced at the cleavage site of its HA molecule. Results rgY55sub (H9N2, which had four basic amino acid residues at the HA cleavage site, replicated in MDCK cells in the absence of trypsin after six consecutive passages in the air sacs of chicks, and acquired intravenous pathogenicity to chicken after four additional passages. More than 75% of chickens inoculated intravenously with the passaged virus, rgY55sub-P10 (H9N2, died, indicating that it is pathogenic comparable to that of highly pathogenic avian influenza viruses (HPAIVs defined by World Organization for Animal Health (OIE. The chickens inoculated with the virus via the intranasal route, however, survived without showing any clinical signs. On the other hand, an avirulent H5N1 strain, A/duck/Hokkaido/Vac-1/2004 (Vac1 (H5N1, acquired intranasal pathogenicity after a pair of di-basic amino acid residues was introduced into the cleavage site of the HA, followed by two passages by air sac inoculation in chicks. Conclusion The present results demonstrate that an H9N2 virus has the potential to acquire intravenous pathogenicity in chickens although the morbidity via the nasal route of infection is lower than that of H5N1 HPAIV.

The C-terminal random coil region tunes the Ca²⁺-binding affinity of S100A4 through conformational activation.

Directory of Open Access Journals (Sweden)

Annette Duelli

Full Text Available S100A4 interacts with many binding partners upon Ca2+ activation and is strongly associated with increased metastasis formation. In order to understand the role of the C-terminal random coil for the protein function we examined how small angle X-ray scattering of the wild-type S100A4 and its C-terminal deletion mutant (residues 1-88, Δ13 changes upon Ca2+ binding. We found that the scattering intensity of wild-type S100A4 changes substantially in the 0.15-0.25 Å-1 q-range whereas a similar change is not visible in the C-terminus deleted mutant. Ensemble optimization SAXS modeling indicates that the entire C-terminus is extended when Ca2+ is bound. Pulsed field gradient NMR measurements provide further support as the hydrodynamic radius in the wild-type protein increases upon Ca2+ binding while the radius of Δ13 mutant does not change. Molecular dynamics simulations provide a rational explanation of the structural transition: the positively charged C-terminal residues associate with the negatively charged residues of the Ca2+-free EF-hands and these interactions loosen up considerably upon Ca2+-binding. As a consequence the Δ13 mutant has increased Ca2+ affinity and is constantly loaded at Ca2+ concentration ranges typically present in cells. The activation of the entire C-terminal random coil may play a role in mediating interaction with selected partner proteins of S100A4.

PKC phosphorylates residues in the N-terminal of the DA transporter to regulate amphetamine-induced DA efflux.

Science.gov (United States)

Wang, Qiang; Bubula, Nancy; Brown, Jason; Wang, Yunliang; Kondev, Veronika; Vezina, Paul

2016-05-27

The DA transporter (DAT), a phosphoprotein, controls extracellular dopamine (DA) levels in the central nervous system through transport or reverse transport (efflux). Multiple lines of evidence support the claim that PKC significantly contributes to amphetamine-induced DA efflux. Other signaling pathways, involving CaMKII and ERK, have also been shown to regulate DAT mediated efflux. Here we assessed the contribution of putative PKC residues (S4, S7, S13) in the N-terminal of the DAT to amphetamine-induced DA efflux by transfecting DATs containing different serine to alanine (S-A) point mutations into DA pre-loaded HEK-293 cells and incubating these cells in amphetamine (2μM). The effects of a S-A mutation at the non-PKC residue S12 and a threonine to alanine (T-A) mutation at the ERK T53 residue were also assessed for comparison. WT-DATs were used as controls. In an initial experiment, we confirmed that inhibiting PKC with Go6976 (130nM) significantly reduced amphetamine-induced DA efflux. In subsequent experiments, cells transfected with the S4A, S12A, S13A, T53A and S4,7,13A mutants showed a reduction in amphetamine-induced DA efflux similar to that observed with Go6976. Interestingly, cells transfected with the S7A mutant, identified by some as a PKC-PKA residue, showed unperturbed WT-DAT levels of amphetamine-induced DA efflux. These results indicate that phosphorylation by PKC of select residues in the DAT N-terminal can regulate amphetamine-induced efflux. PKC can act either independently or in concert with other kinases such as ERK to produce this effect. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent

International Nuclear Information System (INIS)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

2015-01-01

Graphical abstract: Schematic representation of possible mechanisms determining the heavy metals immobilization efficiencyof ASR dust/thermal residues after treatment with nanometallic Ca/CaO/PO 4 . - Highlights: • Nanometallic Ca/CaO/PO 4 for heavy metals immobilization in ASR residue. • Heavy metals immobilization in dry condition attained about 95–100%. • Remaining heavy metals were lower than the Korean standard regulatory limit. • The amounts of heavy metals detectable on the ASR dust surface decreased. • Nanometallic Ca/CaO/PO 4 has a promising potential for heavy metal remediation. - Abstract: This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO 4 dispersion mixture immobilized 95–100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO 4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO 4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO 4 − associated crystalline complexes, and that immobile Ca/PO 4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO 4 as a simple, suitable and highly efficient material for the gentle

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent

Energy Technology Data Exchange (ETDEWEB)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Mitoma, Yoshiharu [Department of Environmental Sciences, Prefectural University of Hiroshima, 562 Nanatsuka-Cho Shobara City, Hiroshima 727-0023 (Japan); Mallampati, Srinivasa Reddy, E-mail: srireddys@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of)

2015-10-15

Graphical abstract: Schematic representation of possible mechanisms determining the heavy metals immobilization efficiencyof ASR dust/thermal residues after treatment with nanometallic Ca/CaO/PO{sub 4}. - Highlights: • Nanometallic Ca/CaO/PO{sub 4} for heavy metals immobilization in ASR residue. • Heavy metals immobilization in dry condition attained about 95–100%. • Remaining heavy metals were lower than the Korean standard regulatory limit. • The amounts of heavy metals detectable on the ASR dust surface decreased. • Nanometallic Ca/CaO/PO{sub 4} has a promising potential for heavy metal remediation. - Abstract: This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO{sub 4} dispersion mixture immobilized 95–100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO{sub 4} was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO{sub 4} mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO{sub 4}− associated crystalline complexes, and that immobile Ca/PO{sub 4} salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO{sub 4} as a simple, suitable and

Solvothermal syntheses, crystal structures, and properties of lanthanide(III) thioarsenates [Ln(dien)2(μ-1κ,2κ2-AsS4)]n (Ln==Sm, Eu, Gd) and [Ln(dien)2(1κ2-AsS4)] (Ln==Tb, Dy, Ho)

International Nuclear Information System (INIS)

Wang, Fang; Tang, Chunying; Chen, Ruihong; Zhang, Yong; Jia, Dingxian

2013-01-01

Solvothermal reactions of Ln 2 O 3 , As and S in diethylenetriamine (dien) at 170 °C for 6 days afforded two structural types of lanthanide thioarsenates with the general formulae [Ln(dien) 2 (μ-1κ,2κ 2 -AsS 4 )] n [Ln=Sm(1), Eu(2), Gd(3)] and [Ln(dien) 2 (1κ 2 -AsS 4 )] [Ln=Tb(4), Dy(5), Ho(6)]. The Ln 2 O 3 oxides were converted to [Ln(dien) 2 ] 3+ complex units in the solvothermal reactions. The As atom binds four S atoms, forming a tetrahedral AsS 4 unit. In 1−3, the AsS 4 units interconnect the [Ln(dien) 2 ] 3+ cations via Ln−S bonds as tridentate μ-1κ,2κ 2 -AsS 4 bridging ligands, resulting in the neutral coordination polymers [Ln(dien) 2 (μ-1κ,2κ 2 -AsS 4 )] n (Ln1). In 4−6, the AsS 4 units coordinate with the Ln 3+ ion of [Ln(dien) 2 ] 3+ as 1κ 2 -AsS 4 chelating ligands to form neutral coordination compounds [Ln(dien) 2 (1κ 2 -AsS 4 )] (Ln2). The Ln 3+ ions are in nine- and eight-coordinated environments in Ln1 and Ln2, respectively. The formation of Ln1 and Ln2 is related with ionic size of the Ln 3+ ions. Optical absorption spectra showed that 1−6 have potential use as semiconductors with the band gaps in the range 2.18−3.21 eV. - Graphical abstract: Two types of Ln-thioarsenates [Ln(dien) 2 (μ-1κ,2κ 2 -AsS 4 )] n and [Ln(dien) 2 (1κ 2 -AsS 4 )] were prepared by solvothermal methods and the soft Lewis basic AsS 4 3– ligand to Ln(III) centers with polyamine co-ligand was obtained. Display Omitted - Highlights: • Lanthanide thioarsenates were prepared by solvothermal methods. • The soft Lewis basic AsS 4 ligand coordinate Ln 3+ ions with coexistence polyamine ligands. • Two structural types of Ln-thioarsenates with structural turnover at Tb were obtained along Ln series. • The Ln-thioarsenates are potential semiconductors with optical band gaps in the range 2.18−3.21 eV

Ketonization of Proline Residues in the Peptide Chains of Actinomycins by a 4-Oxoproline Synthase.

Science.gov (United States)

Semsary, Siamak; Crnovčić, Ivana; Driller, Ronja; Vater, Joachim; Loll, Bernhard; Keller, Ullrich

2018-04-04

X-type actinomycins (Acms) contain 4-hydroxyproline (Acm X 0 ) or 4-oxoproline (Acm X 2 ) in their β-pentapeptide lactone rings, whereas their α ring contains proline. We demonstrate that these Acms are formed through asymmetric condensation of Acm half molecules (Acm halves) containing proline with 4-hydroxyproline- or 4-oxoproline-containing Acm halves. In turn, we show-using an artificial Acm half analogue (PPL 1) with proline in its peptide chain-their conversion into the 4-hydroxyproline- and 4-oxoproline-containing Acm halves, PPL 0 and PPL 2, in mycelial suspensions of Streptomyces antibioticus. Two responsible genes of the Acm X biosynthetic gene cluster of S. antibioticus, saacmM and saacmN, encoding a cytochrome P450 monooxygenase (Cyp) and a ferredoxin were identified. After coexpression in Escherichia coli, their gene products converted PPL 1 into PPL 0 and PPL 2 in vivo as well as in situ in permeabilized cell of the transformed E. coli strain in conjunction with the host-encoded ferredoxin reductase in a NADH (NADPH)-dependent manner. saAcmM has high sequence similarity to the Cyp107Z (Ema) family of Cyps, which can convert avermectin B1 into its keto derivative, 4''-oxoavermectin B1. Determination of the structure of saAcmM reveals high similarity to the Ema structure but with significant differences in residues decorating their active sites, which defines saAcmM and its orthologues as a distinct new family of peptidylprolineketonizing Cyp. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Global Harmonization of Maximum Residue Limits for Pesticides.

Science.gov (United States)

Ambrus, Árpád; Yang, Yong Zhen

2016-01-13

International trade plays an important role in national economics. The Codex Alimentarius Commission develops harmonized international food standards, guidelines, and codes of practice to protect the health of consumers and to ensure fair practices in the food trade. The Codex maximum residue limits (MRLs) elaborated by the Codex Committee on Pesticide Residues are based on the recommendations of the FAO/WHO Joint Meeting on Pesticides (JMPR). The basic principles applied currently by the JMPR for the evaluation of experimental data and related information are described together with some of the areas in which further developments are needed.

Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent.

Science.gov (United States)

Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

2015-10-15

This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO4 dispersion mixture immobilized 95-100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO4- associated crystalline complexes, and that immobile Ca/PO4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO4 as a simple, suitable and highly efficient material for the gentle immobilization of heavy metals in hazardous ASR thermal residue in dry condition. Copyright © 2015 Elsevier B.V. All rights reserved.

Antibacterial Properties of Silver Nanoparticles Embedded on Polyelectrolyte Hydrogels Based on α-Amino Acid Residues

Directory of Open Access Journals (Sweden)

Mario Casolaro

2018-05-01

Full Text Available Polyelectrolyte hydrogels bearing l-phenylalanine (PHE, l-valine (AVA, and l-histidine (Hist residues were used as scaffolds for the formation of silver nanoparticles by reduction of Ag+ ions with NaBH4. The interaction with the metal ion allowed a prompt collapse of the swollen hydrogel, due to the neutralization reaction of basic groups present on the polymer. The imidazole nitrogen of the hydrogel with Hist demonstrated greater complexing capacity with the Ag+ ion compared to the hydrogels with carboxyl groups. The subsequent reduction to metallic silver allowed for the restoration of the hydrogel’s degree of swelling to the starting value. Transmission electron microscopy (TEM and spectroscopic analyses showed, respectively, a uniform distribution of the 15 nm spherical silver nanoparticles embedded on the hydrogel and peak optical properties around a wavelength of 400 nm due to the surface plasmonic effect. Unlike native hydrogels, the composite hydrogels containing silver nanoparticles showed good antibacterial activity as gram+/gram− bactericides, and higher antifungal activity against S. cerevisiae.

Multiple roles of the extracellular vestibule amino acid residues in the function of the rat P2X4 receptor.

Directory of Open Access Journals (Sweden)

Milos B Rokic

Full Text Available The binding of ATP to trimeric P2X receptors (P2XR causes an enlargement of the receptor extracellular vestibule, leading to opening of the cation-selective transmembrane pore, but specific roles of vestibule amino acid residues in receptor activation have not been evaluated systematically. In this study, alanine or cysteine scanning mutagenesis of V47-V61 and F324-N338 sequences of rat P2X4R revealed that V49, Y54, Q55, F324, and G325 mutants were poorly responsive to ATP and trafficking was only affected by the V49 mutation. The Y54F and Y54W mutations, but not the Y54L mutation, rescued receptor function, suggesting that an aromatic residue is important at this position. Furthermore, the Y54A and Y54C receptor function was partially rescued by ivermectin, a positive allosteric modulator of P2X4R, suggesting a rightward shift in the potency of ATP to activate P2X4R. The Q55T, Q55N, Q55E, and Q55K mutations resulted in non-responsive receptors and only the Q55E mutant was ivermectin-sensitive. The F324L, F324Y, and F324W mutations also rescued receptor function partially or completely, ivermectin action on channel gating was preserved in all mutants, and changes in ATP responsiveness correlated with the hydrophobicity and side chain volume of the substituent. The G325P mutant had a normal response to ATP, suggesting that G325 is a flexible hinge. A topological analysis revealed that the G325 and F324 residues disrupt a β-sheet upon ATP binding. These results indicate multiple roles of the extracellular vestibule amino acid residues in the P2X4R function: the V49 residue is important for receptor trafficking to plasma membrane, the Y54 and Q55 residues play a critical role in channel gating and the F324 and G325 residues are critical for vestibule widening.

The quantitative assessment of the role played by basic amino acid clusters in the nuclear uptake of human ribosomal protein L7

International Nuclear Information System (INIS)

Tai, Lin-Ru; Chou, Chang-Wei; Lee, I-Fang; Kirby, Ralph; Lin, Alan

2013-01-01

In this study, we used a multiple copy (EGFP) 3 reporter system to establish a numeric nuclear index system to assess the degree of nuclear import. The system was first validated by a FRAP assay, and then was applied to evaluate the essential and multifaceted nature of basic amino acid clusters during the nuclear import of ribosomal protein L7. The results indicate that the sequence context of the basic cluster determines the degree of nuclear import, and that the number of basic residues in the cluster is irrelevant; rather the position of the pertinent basic residues is crucial. Moreover, it also found that the type of carrier protein used by basic cluster has a great impact on the degree of nuclear import. In case of L7, importin β2 or importin β3 are preferentially used by clusters with a high import efficiency, notwithstanding that other importins are also used by clusters with a weaker level of nuclear import. Such a preferential usage of multiple basic clusters and importins to gain nuclear entry would seem to be a common practice among ribosomal proteins in order to ensure their full participation in high rate ribosome synthesis. - Highlights: ► We introduce a numeric index system that represents the degree of nuclear import. ► The rate of nuclear import is dictated by the sequence context of the basic cluster. ► Importin β2 and β3 were mainly responsible for the N4 mediated nuclear import

The quantitative assessment of the role played by basic amino acid clusters in the nuclear uptake of human ribosomal protein L7

Energy Technology Data Exchange (ETDEWEB)

Tai, Lin-Ru [Institute of Genome Sciences, National Yang-Ming University, Taipei, Taiwan, ROC (China); Chou, Chang-Wei [Institute of Clinical Dentistry Science, National Yang-Ming University, Taipei, Taiwan, ROC (China); Lee, I-Fang; Kirby, Ralph [Institute of Genome Sciences, National Yang-Ming University, Taipei, Taiwan, ROC (China); Lin, Alan, E-mail: alin@ym.edu.tw [Institute of Genome Sciences, National Yang-Ming University, Taipei, Taiwan, ROC (China); Institute of Clinical Dentistry Science, National Yang-Ming University, Taipei, Taiwan, ROC (China)

2013-02-15

In this study, we used a multiple copy (EGFP){sub 3} reporter system to establish a numeric nuclear index system to assess the degree of nuclear import. The system was first validated by a FRAP assay, and then was applied to evaluate the essential and multifaceted nature of basic amino acid clusters during the nuclear import of ribosomal protein L7. The results indicate that the sequence context of the basic cluster determines the degree of nuclear import, and that the number of basic residues in the cluster is irrelevant; rather the position of the pertinent basic residues is crucial. Moreover, it also found that the type of carrier protein used by basic cluster has a great impact on the degree of nuclear import. In case of L7, importin β2 or importin β3 are preferentially used by clusters with a high import efficiency, notwithstanding that other importins are also used by clusters with a weaker level of nuclear import. Such a preferential usage of multiple basic clusters and importins to gain nuclear entry would seem to be a common practice among ribosomal proteins in order to ensure their full participation in high rate ribosome synthesis. - Highlights: ► We introduce a numeric index system that represents the degree of nuclear import. ► The rate of nuclear import is dictated by the sequence context of the basic cluster. ► Importin β2 and β3 were mainly responsible for the N4 mediated nuclear import.

Investigation of the possibility of using residual heat reactor energy

Science.gov (United States)

Aminov, R. Z.; Yurin, V. E.; Bessonov, V. N.

2017-11-01

The largest contribution to the probable frequency of core damage is blackout events. The main component of the heat capacity at each reactor within a few minutes following a blackout is the heat resulting from the braking of beta-particles and the transfer of gamma-ray energy by the fission fragments and their decay products, which is known as the residual heat. The power of the residual heat changes gradually over a long period of time and for a VVER-1000 reactor is about 15-20 MW of thermal power over 72 hours. Current cooldown systems increase the cost of the basic nuclear power plants (NPP) funds without changing the amount of electricity generated. Such systems remain on standby, accelerating the aging of the equipment and accordingly reducing its reliability. The probability of system failure increases with the duration of idle time. Furthermore, the reactor residual heat energy is not used. A proposed system for cooling nuclear power plants involves the use of residual thermal power to supply the station’s own needs in emergency situations accompanied by a complete blackout. The thermal power of residual heat can be converted to electrical energy through an additional low power steam turbine. In normal mode, the additional steam turbine generates electricity, which makes it possible to ensure spare NPP and a return on the investment in the reservation system. In this work, experimental data obtained from a Balakovo NPP was analyzed to determine the admissibility of cooldown of the reactors through the 2nd circuit over a long time period, while maintaining high-level parameters for the steam generated by the steam generators.

Validation of pestice multi residue analysis method on cucumber

International Nuclear Information System (INIS)

2011-01-01

In this study we aimed to validate the method of multi pesticide residue analysis on cucumber. Before real sample injection, system suitability test was performed in gas chromatography (GC). For this purpose, a sensitive pesticide mixture was used for GC-NPD and estimated the performance parameters such as number of effective theoretical plates, resolution factor, asymmetry, tailing and selectivity. It was detected that the system was suitable for calibration and sample injection. Samples were fortified at the level of 0.02, 0.2, 0.8 and 1 mg/kg with mixture of dichlorvos, malathion and chloropyrifos pesticides. In the fortification step 1 4C-carbaryl was also added on homogenized analytical portions to make use of 1 4C labelled pesticides for the determining extraction efficiency. Then the basic analytical process, such as ethyl acetate extraction, filtration, evaporation and cleanup, were performed. The GPC calibration using 1 4C- carbaryl and fortification mixture (dichlorvos, malathion and chloropyrifos) showed that pesticide fraction come through the column between the 8-23 ml fractions. The recovery of 1 4C-carbaryl after the extraction and cleanup step were 92.63-111.73 % and 74.83-102.22 %, respectively. The stability of pesticides during analysis is an important factor. In this study, stability test was performed including matrix effect. Our calculation and t test results showed that above mentioned pesticides were not stabile during sample processing in our laboratory conditions and it was found that sample comminution with dry ice may improve stability. In the other part of the study, 1 4C-chloropyrifos was used to determine homogeneity of analytical portions taken from laboratory samples. Use of 1 4C labelled pesticides allows us for quick quantification analyte, even with out clean-up. The analytical results show that after sample processing with waring blender, analytical portions were homogenous. Sample processing uncertainty depending on quantity of

Residual Stress Analysis for Engineering Applications by Means of Neutron Diffraction

International Nuclear Information System (INIS)

Gndupel-Herold, Thomas; Brand, Paul C.; Prask, Henry J.

1999-01-01

The economic and scientific importance of neutron diffraction residual stress analysis has led to an increasing number of suitable instruments worldwide. Recently, a dedicated state-of-the-art diffractometer has been installed at the National Institute of Standards and Technology reactor. It has been used for a variety of measurements on basic and engineering stress problems. Among the most prominent examples that have been investigated are residual stresses in rails, weldments, and plasma-sprayed coatings

Residual stress relaxation due to fretting fatigue in shot peened surfaces of Ti-6Al-4V

International Nuclear Information System (INIS)

Martinez, S.A.; Blodgett, M.P.; Mall, S.; Sathish, S.; Namjoshi, S.

2003-01-01

Fretting fatigue occurs at locations where the materials are sliding against each other under load. In order to enhance the fatigue life under fretting conditions the surface of the component is shot peened. In general, the shot peening process produces a compressive stress on the surface of the material, thereby increasing the resistance of the material to crack initiation. This paper presents the relaxation of residual stress caused during fretting fatigue. X-ray diffraction has been utilized as the method to measure residual stress in fretting fatigued samples of Ti-6Al-4V

A cluster of aspartic residues in the extracellular loop II of PAR 4 is important for thrombin interaction and activation of platelets.

Science.gov (United States)

Sánchez Centellas, Daniel; Gudlur, Sushanth; Vicente-Carrillo, Alejandro; Ramström, Sofia; Lindahl, Tomas L

2017-06-01

Thrombin activates platelets via proteolytic cleavage of protease-activated receptors (PARs) 1 and 4. The two PARs have distinct but complementary roles. The mechanisms responsible for PAR1 activation by thrombin have been extensively studied. However, much less is known regarding thrombin activation of PAR4, especially the potential involvement of regions of PAR4 other than the N-terminal, which is bound to the catalytic site of thrombin. We have studied PAR4 in S. cerevisiae strain MMY12, an expression system in which the GPCR receptors are connected to a Lac Z reporter gene resulting in increased β-galactosidase activity. This approach was used to assess PAR4 mutants to evaluate the contribution of different aspartic residues in facilitating PAR4 activation. Furthermore, peptides mimicking parts of the PAR4 N-terminal and the second extracellular loop (ECLII) were tested for their ability to inhibit platelet activation by thrombin. Binding of these peptides to γ-thrombin was studied by monitoring the decrease in tryptophan fluorescence intensity of thrombin. We conclude that not only the N-terminal but also the electronegative aspartic residues D224, D230 and D235 (located in ECLII) are be important for PAR4 binding to thrombin. We further suggest that they play a role for the tethered ligand binding to the receptor, as mutations also affected activation in response to a PAR4-activating peptide mimicking the new N-terminal formed after cleavage. This agrees with previous results on PAR1 and thrombin binding. We suggest that the ECLII of PAR4 could be a potential target for antithrombotic drug development. Copyright © 2017 Elsevier Ltd. All rights reserved.

Niflumic acid alters gating of HCN2 pacemaker channels by interaction with the outer region of S4 voltage sensing domains.

Science.gov (United States)

Cheng, Lan; Sanguinetti, Michael C

2009-05-01

Niflumic acid, 2-[[3-(trifluoromethyl)phenyl]amino]pyridine-3-carboxylic acid (NFA), is a nonsteroidal anti-inflammatory drug that also blocks or modifies the gating of many ion channels. Here, we investigated the effects of NFA on hyperpolarization-activated cyclic nucleotide-gated cation (HCN) pacemaker channels expressed in X. laevis oocytes using site-directed mutagenesis and the two-electrode voltage-clamp technique. Extracellular NFA acted rapidly and caused a slowing of activation and deactivation and a hyperpolarizing shift in the voltage dependence of HCN2 channel activation (-24.5 +/- 1.2 mV at 1 mM). Slowed channel gating and reduction of current magnitude was marked in oocytes treated with NFA, while clamped at 0 mV but minimal in oocytes clamped at -100 mV, indicating the drug preferentially interacts with channels in the closed state. NFA at 0.1 to 3 mM shifted the half-point for channel activation in a concentration-dependent manner, with an EC(50) of 0.54 +/- 0.068 mM and a predicted maximum shift of -38 mV. NFA at 1 mM also reduced maximum HCN2 conductance by approximately 20%, presumably by direct block of the pore. The rapid onset and state-dependence of NFA-induced changes in channel gating suggests an interaction with the extracellular region of the S4 transmembrane helix, the primary voltage-sensing domain of HCN2. Neutralization (by mutation to Gln) of any three of the outer four basic charged residues in S4, but not single mutations, abrogated the NFA-induced shift in channel activation. We conclude that NFA alters HCN2 gating by interacting with the extracellular end of the S4 voltage sensor domains.

Basic Energy Sciences at NREL

Energy Technology Data Exchange (ETDEWEB)

Moon, S.

2000-12-04

NREL's Center for Basic Sciences performs fundamental research for DOE's Office of Science. Our mission is to provide fundamental knowledge in the basic sciences and engineering that will underpin new and improved renewable energy technologies.

29 CFR 1620.1 - Basic applicability of the Equal Pay Act.

Science.gov (United States)

2010-07-01

... 29 Labor 4 2010-07-01 2010-07-01 false Basic applicability of the Equal Pay Act. 1620.1 Section 1620.1 Labor Regulations Relating to Labor (Continued) EQUAL EMPLOYMENT OPPORTUNITY COMMISSION THE EQUAL PAY ACT § 1620.1 Basic applicability of the Equal Pay Act. (a) Since the Equal Pay Act, 29 U.S.C...

Babassu nut residues: potential for bioenergy use in the North and Northeast of Brazil.

Science.gov (United States)

de Paula Protásio, Thiago; Fernando Trugilho, Paulo; da Silva César, Antônia Amanda; Napoli, Alfredo; Alves de Melo, Isabel Cristina Nogueira; Gomes da Silva, Marcela

2014-01-01

Babassu is considered the largest native oil resource worldwide and occurs naturally in Brazil. The purpose of this study was to evaluate the potential of babassu nut residues (epicarp, mesocarp and endocarp) for bioenergy use, especially for direct combustion and charcoal production. The material was collected in the rural area of the municipality of Sítio Novo do Tocantins, in the state of Tocantins, Brazil. Analyses were performed considering jointly the three layers that make up the babassu nut shell. The following chemical characterizations were performed: molecular (lignin, total extractives and holocellulose), elemental (C, H, N, S and O), immediate (fixed carbon, volatiles and ash), energy (higher heating value and lower heating value), physical (basic density and energy density) and thermal (thermogravimetry and differential thermal analysis), besides the morphological characterization by scanning electron microscopy. Babassu nut residues showed a high bioenergy potential, mainly due to their high energy density. The use of this biomass as a bioenergy source can be highly feasible, given their chemical and thermal characteristics, combined with a low ash content. Babassu nut shell showed a high basic density and a suitable lignin content for the sustainable production of bioenergy and charcoal, capable of replacing coke in Brazilian steel plants.

S.P.S.S. User's Manual #1-#4. Basic Program Construction in S.P.S.S.; S.P.S.S. Non-Procedural Statements and Procedural Commands; System Control Language and S.P.S.S.; Quick File Equate Statement Reference.

Science.gov (United States)

Earl, Lorna L.

This series of manuals describing and illustrating the Statistical Package for the Social Sciences (SPSS) was planned as a self-teaching instrument, beginning with the basics and progressing to an advanced level. Information on what the searcher must know to define the data and write a program for preliminary analysis is contained in manual 1,…

Estimating Net Interracial Mobility in the U.S. A Residual Methods Approach.

Science.gov (United States)

Perez, Anthony Daniel; Hirschman, Charles

2009-08-01

This paper presents a residual methods approach to identifying social mobility across race/ethnic categories. In traditional demographic accounting models, population growth is limited to changes in natural increase and migration. Other sources of growth are absorbed by the model residual and can only be estimated indirectly. While these residual estimates have been used to illuminate a number of elusive demographic processes, there has been little effort to incorporate shifts in racial identification into formal accounts of population change. In light of growing evidence that a number of Americans view race/ethnic identities as a personal choice, and not a fixed characteristic, mobility across racial categories may play important roles in the growth of race/ethnic sub-populations and changes to the composition of the U.S. To examine this potential, we derive a reduced-form population balancing equation that treats fertility and international migration as given and estimates survival from period life table data. After subtracting out national increase and migration and adjusting the balance of observed growth for changes in racial measurement and census coverage, we argue that the remaining error of closure provides a reasonable estimate of net interracial mobility among the native born. Using recent Census and ACS microdata, we illustrate the impact that identity shifts may have had on the growth of race/ethnic sub-populations in the past quarter century. Findings suggest a small drift from the non-Hispanic white population into race/ethnic minority groups, though the pattern varies by age and between time periods.

SARS-coronavirus spike S2 domain flanked by cysteine residues C822 and C833 is important for activation of membrane fusion

International Nuclear Information System (INIS)

Madu, Ikenna G.; Belouzard, Sandrine; Whittaker, Gary R.

2009-01-01

The S2 domain of the coronavirus spike (S) protein is known to be responsible for mediating membrane fusion. In addition to a well-recognized cleavage site at the S1-S2 boundary, a second proteolytic cleavage site has been identified in the severe acute respiratory syndrome coronavirus (SARS-CoV) S2 domain (R797). C-terminal to this S2 cleavage site is a conserved region flanked by cysteine residues C822 and C833. Here, we investigated the importance of this well conserved region for SARS-CoV S-mediated fusion activation. We show that the residues between C822-C833 are well conserved across all coronaviruses. Mutagenic analysis of SARS-CoV S, combined with cell-cell fusion and pseudotyped virion infectivity assays, showed a critical role for the core-conserved residues C822, D830, L831, and C833. Based on available predictive models, we propose that the conserved domain flanked by cysteines 822 and 833 forms a loop structure that interacts with components of the SARS-CoV S trimer to control the activation of membrane fusion.

Mapping the residues of protein kinase CK2 implicated in substrate recognition

DEFF Research Database (Denmark)

Sarno, S; Boldyreff, B; Marin, O

1995-01-01

, hampering the calculation of kinetic parameters. In contrast 3 mutants (K74-77A, K79R80K83A and R191,195K198A) phosphorylated the peptide with reduced efficiency accounted for by increased Km and decreased Vmax values. By using derivatives of the RRRADDSDDDDD peptide in which individual aspartyl residues......, respectively. These data support the conclusion that the basic residues present in the p+1 loop of CK2 alpha specifically recognize the acidic determinant adjacent to the C-terminal side of serine, while the specificity determinants located more down-stream are variably recognized by different residues...

Postoperative Residual Neuromuscular Paralysis at an Australian Tertiary Children’s Hospital

Directory of Open Access Journals (Sweden)

Thomas Ledowski

2015-01-01

Full Text Available Purpose. Residual neuromuscular blockade (RNMB is known to be a significant but frequently overlooked complication after the use of neuromuscular blocking agents (NMBA. Aim of this prospective audit was to investigate the incidence and severity of RNMB at our Australian tertiary pediatric center. Methods. All children receiving NMBA during anesthesia were included over a 5-week period at the end of 2011 (Mondays to Fridays; 8 a.m.–6 p.m.. At the end of surgery, directly prior to tracheal extubation, the train-of-four (TOF ratio was assessed quantitatively. Data related to patient postoperative outcome was collected in the postoperative acute care unit. Results. Data of 64 patients were analyzed. Neostigmine was given in 34 cases and sugammadex in 1 patient. The incidence of RNMB was 28.1% overall (without reversal: 19.4%; after neostigmine: 37.5%; n.s.. Severe RNMB (TOF ratio < 0.7 was found in 6.5% after both no reversal and neostigmine, respectively. Complications in the postoperative acute care unit were infrequent, with no differences between reversal and no reversal groups. Conclusions. In this audit, RNMB was frequently observed, particularly in cases where patients were reversed with neostigmine. These findings underline the well-known problems associated with the use of NMBA that are not fully reversed.

The role of basic leucine zipper transcription factor E4BP4 in the immune system and immune-mediated diseases.

Science.gov (United States)

Yin, Jinghua; Zhang, Jian; Lu, Qianjin

2017-07-01

Basic leucine zipper transcription factor E4BP4 (also known as NFIL3) has been implicated in the molecular and cellular mechanisms of functions and activities in mammals. The interactions between E4BP4 and major regulators of cellular processes have triggered significant interest in the roles of E4BP4 in the pathogenesis of certain chronic diseases. Indeed, novel discoveries have been emerging to illustrate the involvement of E4BP4 in multiple disorders. It is recognized that E4BP4 is extensively involved in some immune-mediated diseases, but the mechanisms of E4BP4 involvement in these complex diseases remain poorly defined. Here we review the regulatory mechanisms of E4BP4 engaging in not only the biological function but also the development of immune-mediated diseases, paving the way for future therapies. Copyright © 2017. Published by Elsevier Inc.

Polychlorinated Biphenyls (PCB) Residue Effects Database

Data.gov (United States)

U.S. Environmental Protection Agency — The PCB Residue Effects (PCBRes) Database was developed to assist scientists and risk assessors in correlating PCB and dioxin-like compound residues with toxic...

Equal Opportunity, Equal Work: Increasing Women's Participation in the U.S. President's Malaria Initiative Africa Indoor Residual Spraying Project

OpenAIRE

Donner, Abigail; Belemvire, Allison; Johns, Ben; Mangam, Keith; Fiekowsky, Elana; Gunn, Jayleen; Hayden, Mary; Ernst, Kacey

2017-01-01

Background: One of the primary control measures for malaria transmission is indoor residual spraying (IRS). Historically, few women have worked in IRS programs, despite the income-generating potential. Increasing women's roles in IRS requires understanding the barriers to women's participation and implementing measures to address them. The U.S. President's Malaria Initiative (PMI) Africa Indoor Residual Spraying (AIRS) Project is the largest implementer of IRS globally. To address gender ineq...

Test and Numerical Analysis for Penetration Residual Velocity of Bullet Considering Failure Strain Uncertainty of Composite Plates

Energy Technology Data Exchange (ETDEWEB)

Cha, Myungseok; Lee, Minhyung [Sejong Univ., Sejong (Korea, Republic of)

2016-03-15

The ballistic performance data of composite materials is distributed due to material inhomogeneity. In this paper, the uncertainty in residual velocity is obtained experimentally, and a method of predicting it is established numerically for the high-speed impact of a bullet into laminated composites. First, the failure strain distribution was obtained by conducting a tensile test using 10 specimens. Next, a ballistic impact test was carried out for the impact of a fragment-simulating projectile (FSP) bullet with 4ply ([0/90]s) and 8ply ([0/90/0/90]s) glass fiber reinforced plastic (GFRP) plates. Eighteen shots were made at the same impact velocity and the residual velocities were obtained. Finally, simulations were conducted to predict the residual velocities by using the failure strain distributions that were obtained from the tensile test. For this simulation, two impact velocities were chosen at 411.7m/s (4ply) and 592.5m/s (8ply). The simulation results show that the predicted residual velocities are in close agreement with test results. Additionally, the modeling of a composite plate with layered solid elements requires less calculation time than modeling with solid elements.

Inpatient Psychiatric Admission Rates in a U.S. Air Force Basic Military Training Population

Science.gov (United States)

2017-05-20

Please know that if you are a Graduate Health Sciences Education student and your department has told you they cannot fund your publication, the 59th...author must complete page two of this form: a. In Section 2, add the funding source for your study (e.g., S9 MOW CRD Graduate Health Sciences...U.S. AIR FORCE BASIC MILITARY TRAINING POPULATION Background: Mental health admission rates for those with no active mental health disorders have

Optimisation and characterisation of silica-based reversed-phase liquid chromatographic systems for the analysis of basic pharmaceuticals

NARCIS (Netherlands)

Vervoort, R.J.M.; Debets, A.J.J.; Claessens, H.A.; Cramers, C.A.M.G.; Jong, de G.J.

2000-01-01

Reversed-phase liquid chromatography using silica-based columns is successfully applied in many separations. However, also some drawbacks exist, i.e. the analysis of basic compounds is often hampered by ionic interaction of the basic analytes with residual silanols present on the silica surface,

40 CFR 180.106 - Diuron; tolerances for residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Diuron; tolerances for residues. 180... Diuron; tolerances for residues. (a) General. Tolerances are established for the combined residues of the herbicide diuron, 3-(3,4-dichlorophenyl)-1,1-dimethylurea and its metabolites convertible to 3,4...

Quasirelativistic calculation of 4s24p5, 4s24p44d and 4s4p6 configuration spectroscopic parameters for the W39+ ion

International Nuclear Information System (INIS)

Bogdanovich, P; Karpuškienė, R; Kisielius, R

2015-01-01

The ab initio quasirelativistic Hartree–Fock method developed specifically for the calculation of spectral parameters of heavy atoms and highly charged ions is used to derive spectral data for the 4s 2 4p 5 , 4s 2 4p 4 4d and 4s4p 6 configurations of the multicharged tungsten ion W 39+ . The relativistic effects are taken into account in the Breit–Pauli approximation for the quasirelativistic Hartree–Fock radial orbitals. The configuration interaction method is applied to include the electron correlation effects. Produced data are compared with existing experimental measurements and theoretical calculations. (paper)

The hyperfine structure constants for the 4s24p and 4s25s states of Ga

International Nuclear Information System (INIS)

Wang Qingmin; Dong Chenzhong

2012-01-01

The hyperfine structure (hfs) constants for the states 4s 2 4p 2 P 1/2,3/2 and 4s 2 5s 2 S 1/2 of 71 Ga were calculated using the GRASP2K package based on the multiconfiguration Dirac-Fock (MCDF) method. The results indicated that the core polarization effect was important for the hyperfine structure constants. (authors)

Residues essential for Panton-Valentine leukocidin S component binding to its cell receptor suggest both plasticity and adaptability in its interaction surface.

Directory of Open Access Journals (Sweden)

Benoit-Joseph Laventie

Full Text Available Panton-Valentine leukocidin (PVL, a bicomponent staphylococcal leukotoxin, is involved in the poor prognosis of necrotizing pneumonia. The present study aimed to elucidate the binding mechanism of PVL and in particular its cell-binding domain. The class S component of PVL, LukS-PV, is known to ensure cell targeting and exhibits the highest affinity for the neutrophil membrane (Kd∼10(-10 M compared to the class F component of PVL, LukF-PV (Kd∼10(-9 M. Alanine scanning mutagenesis was used to identify the residues involved in LukS-PV binding to the neutrophil surface. Nineteen single alanine mutations were performed in the rim domain previously described as implicated in cell membrane interactions. Positions were chosen in order to replace polar or exposed charged residues and according to conservation between leukotoxin class S components. Characterization studies enabled to identify a cluster of residues essential for LukS-PV binding, localized on two loops of the rim domain. The mutations R73A, Y184A, T244A, H245A and Y250A led to dramatically reduced binding affinities for both human leukocytes and undifferentiated U937 cells expressing the C5a receptor. The three-dimensional structure of five of the mutants was determined using X-ray crystallography. Structure analysis identified residues Y184 and Y250 as crucial in providing structural flexibility in the receptor-binding domain of LukS-PV.

Hydraulic Conductivity of Residual Soil-Cement Mix

Science.gov (United States)

Govindasamy, P.; Taha, M. R.

2016-07-01

In Malaysia, although there are several researches on engineering properties of residual soils, however study on the hydraulic conductivity properties of metasedimentary residual soils is still lacking. Construction of containment walls like slurry wall techniques can be achieved with hydraulic conductivity of approximately 5 x 10-7cm/sec. The objectives of the study were to determine the physical properties of metasedimentary residual soils and to determine the influence of 1%, 3%, 5% and 10% of cement on hydraulic conductivity parameters. The coefficient of hydraulic conductivity of the soil naturally and soil-cement mixtures were determined by using the falling head test. According to the test, the hydraulic conductivity of the original soil was 4.16 x 10-8 m/s. The value decreases to 3.89 x 10-8 m/s, 2.78 x 10-8 m/s then 6.83 x 10-9 m/s with the addition of 1%, 3% and 5% of cement additives, respectively. During the hydration process, cement hydrates is formed followed by the increase in pH value and Ca(OH)2 which will alter the modification of pores size and distribution. When the quantity of cement increases, the pores size decrease. But, the addition of 10% cement gives an increased hydraulic conductivity value to 2.78 x 10-8 m/s. With 10%, the pore size increase might due to flocculation and agglomeration reaction. The generated hydraulic conductivity values will indirectly become a guide in the preliminary soil cement stabilization to modify the properties of the soil to become more like the properties of a soft rock.1. Introduction

Multiple native-like conformations trapped via self-association-induced hydrophobic collapse of the 33-residue beta-sheet domain from platelet factor 4.

OpenAIRE

Ilyina, E; Mayo, K H

1995-01-01

Native platelet factor 4 (PF4) (70 residues) has a hydrophobic three-stranded anti-parallel beta-sheet domain on to which is folded an amphipathic C-terminal alpha-helix and an aperiodic N-terminal domain. The 33-amino acid beta-sheet domain from PF4 (residues 23-55) has been synthesized and studied by c.d. and n.m.r. At 10 degrees C and low concentration, peptide 23-55 appears to exist in aqueous solution in a random-coil distribution of highly flexible conformational states. Some preferred ...

Hydrocracking of atmospheric distillable residue of Mongolian oil

Directory of Open Access Journals (Sweden)

Ts Tugsuu

2014-09-01

Full Text Available Many catalytic processes to refine heavy part of crude oil have attracted much interest due to declining reserves of light crude oils. This study focused on hydrocracking process of atmospheric distillable residue of Mongolian crude oil in the first time compared to those of other countries. Residue samples were hydrocracked with a commercial catalyst at 450°C, 460°C, 470°C for 2 h under hydrogen pressure of 10 MPa. The amount of residual fraction (350°C4wt% by the hydrocracking of atmospheric distillable residue from Tamsagbulag crude oil. When the ME-AR was hydrocracked, the high consumption of hydrogen was related to the lowest H/C atomic ratio of feed atmospheric residue. The amount of liquid fractions (BP<350°C including gaseous products increased from 45.4wt% to 89.2wt%, when the reaction temperature increased from 450°C to 470°C. The highest yield of the middle fraction for each sample was observed at temperature of 460°C. On the other hand, the effect of temperature on the yield of middle fraction was not so high as compared with the yields of other fractions. The contents of n-paraffins on midlle and heavy fractions of TB-AR, DQ-AR were similar, but ME-AR’s was around 2 times lower than other after hydrocracking runs.DOI: http://dx.doi.org/10.5564/mjc.v12i0.166 Mongolian Journal of Chemistry Vol.12 2011: 24-28 

An assay of the utilization of the residual use of a N fertilizer [(15NH4)2SO4] made by a wheat crop, using an isotope technique

International Nuclear Information System (INIS)

Bujan, A.; Quitegui, M.I.; Quitegui, M.C.; Ghelfi, L.E.P. de; Deybe, D.

1982-01-01

An experimental study was carried out in order to determine the residual use of a N fertilizer made by wheat during a year. Wheat was seeded in plots which had been cropped the year before with inoculated soybean (glycine max), non-inoculated soybean and sorghum (sorghum caffrorum) fertilized with (NH 4 ) 2 SO 4 at two different levels: 20 and 100kg N/ha tagged with 5% excess 15 N and 1% respectively. It was concluded that:1) the % excess 15 N used in the previous crops were sufficient to determine residuality from the N fertilizer. 2)when the previous crop was non-inoculated soybean, the total nitrogen content of the wheat grains was significantly higher than when the previous crop was either inoculated soybean or sorghum. The total N content was significantly higher on the plots fertilized with 100KgN/ha than on those with 20kgN/ha.3) non-inoculated - and inoculated soybeans determined higher wheat grain yields than sorghum as previous crops. Higher wheat grain yields ocurred on the 100kgN/ha fertilized plots. Higher residual N content ocurred on the 100KgN/ha fertilized plots. Non-inoculated soybean determined higher residual N content in grain than inoculated soybean and sorghum; inoculated soybean determined higher content than sorghum. There were no significant differences in residual N content in the plants depending on the previous crop. (Author) [pt

Heat transfer properties of organic coolants containing high boiling residues

International Nuclear Information System (INIS)

Debbage, A.G.; Driver, M.; Waller, P.R.

1964-01-01

Heat transfer measurements were made in forced convection with Santowax R, mixtures of Santowax R and pyrolytic high boiling residue, mixtures of Santowax R and CMRE Radiolytic high boiling residue, and OMRE coolant, in the range of Reynolds number 10 4 to 10 5 . The data was correlated with the equation Nu = 0.015 Re b 0.85 Pr b 0.4 with an r.m.s. error of ± 8.5%. The total maximum error arising from the experimental method and inherent errors in the physical property data has been estimated to be less than ± 8.5%. From the correlation and physical property data, the decrease in heat transfer coefficient with increasing high boiling residue concentration has been determined. It has been shown that subcooled boiling in organic coolants containing high boiling residues is a complex phenomenon and the advantages to be gained by operating a reactor in this region may be marginal. Gas bearing pumps used initially in these experiments were found to be unsuitable; a re-designed ball bearing system lubricated with a terphenyl mixture was found to operate successfully. (author)

Distribution of Penicillin G Residues in Culled Dairy Cow Muscles: Implications for Residue Monitoring

Science.gov (United States)

The U.S. Food and Drug Administration sets tolerances for veterinary drug residues in muscle, but does not specify which type of muscle should be analyzed. In order to determine if antibiotic residue levels are dependent on muscle type, 7 culled dairy cows were dosed with Penicillin G (Pen G) from ...

Kinetic enantioselectivity of a protonated bis(diamido)-bridged basket resorcin[4]arene towards alanine peptides.

Science.gov (United States)

Fraschetti, C; Montagna, M; Crestoni, M E; Calcaterra, A; Aiello, F; Santi, L; Filippi, A

2017-02-01

Efficient enantiodiscrimination of some alanine-containing di- and tri-peptides by using chiral protonated bis(diamido)-bridged basket resorcin[4]arenes depends on several factors, including the basicity of the amino acid residues at the C- and N-termini of the peptide.

Residual effect of mixture of glyphosate and 2,4-D in winter maize in different soil textures

Directory of Open Access Journals (Sweden)

Schaianne A. Gomes

Full Text Available ABSTRACT To increase the efficiency in the control of weeds, it is common the use of a mixture of the herbicides glyphosate and 2,4-D in the desiccation. This paper aimed to evaluate the residual effect of these two herbicides on the development of maize plants, in soils of different textures. The experiment was conducted in a greenhouse, in 2015, in a completely randomized design in a 2 x 2 x 7 factorial scheme, corresponding to two soils (Red Yellow Latosol and Quartzarenic Neosol, two herbicide application times (5 and 10 days before maize sowing and seven doses of herbicides (recommended dose of glyphosate, recommended dose of 2,4-D; mixing the recommended doses of glyphosate and 2,4-D; two, ten and fifty times the recommended doses in admixture; and one control, with 4 replicates. After emergence of maize plants, the following variables were evaluated: phytotoxicity, plant height, chlorophyll a and chlorophyll b, shoot fresh and dry matter and root dry matter. In general, there was lower residual effect on the Red Yellow Latosol at all the doses of the herbicides and in the interval of 10 days between the desiccation and sowing.

Removal of Basic Nitrogen Compounds from Fuel Oil with [Hnmp]H2PO4 Ionic Liquid

Directory of Open Access Journals (Sweden)

Z. Zhou

2017-04-01

Full Text Available Ionic liquid (IL N-methyl pyrrolidone dihydrogen phosphate ([Hnmp]H2PO4 was synthesized and its structure was characterized with FT-IR spectroscopy and 1H NMR. The denitrogenation performance of the ionic liquid was investigated using Fushun shale diesel oil that included 0.52 w% basic nitrogen as feedstock. Experiment results showed that under the operating conditions with temperature of 30 °C, 1:7 (w/w IL: oil, reaction time of 20 min, and settling time of 2 h, the ionic liquid exhibited good denitrogenation performance achieving 86.27 % basic N-extraction efficiency and the yield of refined diesel oil can reach more than 90 %. In addition, the basic N-removal efficiency can still reach 54 % during four recycles of the ionic liquid.

Residual stresses around Vickers indents

International Nuclear Information System (INIS)

Pajares, A.; Guiberteau, F.; Steinbrech, R.W.

1995-01-01

The residual stresses generated by Vickers indentation in brittle materials and their changes due to annealing and surface removal were studied in 4 mol% yttria partially stabilized zirconia (4Y-PSZ). Three experimental methods to gain information about the residual stress field were applied: (i) crack profile measurements based on serial sectioning, (ii) controlled crack propagation in post indentation bending tests and (iii) double indentation tests with smaller secondary indents located around a larger primary impression. Three zones of different residual stress behavior are deduced from the experiments. Beneath the impression a crack free spherical zone of high hydrostatic stresses exists. This core zone is followed by a transition regime where indentation cracks develop but still experience hydrostatic stresses. Finally, in an outward third zone, the crack contour is entirely governed by the tensile residual stress intensity (elastically deformed region). Annealing and surface removal reduce this crack driving stress intensity. The specific changes of the residual stresses due to the post indentation treatments are described and discussed in detail for the three zones

Mapping residual and internal stress in materials by neutron diffraction

International Nuclear Information System (INIS)

Withers, Ph.J.

2007-01-01

Neutron diffraction provides one of the few means of mapping residual stresses deep within the bulk of materials and components. This article reviews the basic scientific methodology by which internal strains and stresses are inferred from recorded diffraction peaks. Both conventional angular scans and time-of-flight measurements are reviewed and compared. Their complementarity with analogous synchrotron X-ray methods is also highlighted. For measurements to be exploited in structural integrity calculations underpinning the safe operation of engineering components, measurement standards have been defined and the major findings are summarised. Examples are used to highlight the unique capabilities of the method showing how it can provide insights ranging from the basic physics of slip mechanisms in hexagonal polycrystalline materials, through the materials optimisation of stress induced transformations in smart nano-materials, to the industrial introduction of novel friction welding processes exploiting stress residual measurements transferred from prototype sub-scale tests to the joining of full-scale aero-engine assemblies. (author)

Function modification of SR-PSOX by point mutations of basic amino acids

Directory of Open Access Journals (Sweden)

Chen Chunxia

2011-04-01

Full Text Available Abstract Background Atherosclerosis (AS is a common cardiovascular disease. Transformation of macrophages to form foam cells by internalizing modified low density-lipoprotein (LDL via scavenger receptor (SR is a key pathogenic process in the onset of AS. It has been demonstrated that SR-PSOX functions as either a scavenger receptor for uptake of atherogenic lipoproteins and bacteria or a membrane-anchored chemokine for adhesion of macrophages and T-cells to the endothelium. Therefore, SR-PSOX plays an important role in the development of AS. In this study the key basic amino acids in the chemokine domain of SR-PSOX have been identified for its functions. Results A cell model to study the functions of SR-PSOX was successfully established. Based on the cell model, a series of mutants of human SR-PSOX were constructed by replacing the single basic amino acid residue in the non-conservative region of the chemokine domain (arginine 62, arginine 78, histidine 80, arginine 82, histidine 85, lysine 105, lysine 119, histidine 123 with alanine (designated as R62A, R78A, H80A, R82A, H85A, K105A, K119A and H123A, respectively. Functional studies showed that the mutants with H80A, H85A, and K105A significantly increased the activities of oxLDL uptake and bacterial phagocytosis compared with the wild-type SR-PSOX. In addition, we have also found that mutagenesis of either of those amino acids strongly reduced the adhesive activity of SR-PSOX by using a highly non-overlapping set of basic amino acid residues. Conclusion Our study demonstrates that basic amino acid residues in the non-conservative region of the chemokine domain of SR-PSOX are critical for its functions. Mutation of H80, H85, and K105 is responsible for increasing SR-PSOX binding with oxLDL and bacteria. All the basic amino acids in this region are important in the cells adhesion via SR-PSOX. These findings suggest that mutagenesis of the basic amino acids in the chemokine domain of SR-PSOX may

Bandgap tuning with thermal residual stresses induced in a quantum dot.

Science.gov (United States)

Kong, Eui-Hyun; Joo, Soo-Hyun; Park, Hyun-Jin; Song, Seungwoo; Chang, Yong-June; Kim, Hyoung Seop; Jang, Hyun Myung

2014-09-24

Lattice distortion induced by residual stresses can alter electronic and mechanical properties of materials significantly. Herein, a novel way of the bandgap tuning in a quantum dot (QD) by lattice distortion is presented using 4-nm-sized CdS QDs grown on a TiO2 particle as an application example. The bandgap tuning (from 2.74 eV to 2.49 eV) of a CdS QD is achieved by suitably adjusting the degree of lattice distortion in a QD via the tensile residual stresses which arise from the difference in thermal expansion coefficients between CdS and TiO2. The idea of bandgap tuning is then applied to QD-sensitized solar cells, achieving ≈60% increase in the power conversion efficiency by controlling the degree of thermal residual stress. Since the present methodology is not limited to a specific QD system, it will potentially pave a way to unexplored quantum effects in various QD-based applications. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Developments in hydroconversion processes for residues

Energy Technology Data Exchange (ETDEWEB)

Douwes, C T [Shell Res. B.V.; Wijffels, J B; Van Klinken, J; Van Zijll Langhout, W C

1979-01-01

A review of recent developments in hydrotreating processes for demetallization, desulfurization, and conversion to distillate products of residues covers catalyst developments for suppression of coke formation, maximum metals tolerance, and conversion selectivity; the effects of hydrogen pressure and temperature on catalyst deactivation and conversion; basic operating characteristics of conventional fixed-bed trickle-flow reactors, and of onstream catalyst replacement reactors, including the expanded-bed and the moving-bed reactor; a comparison of catalyst bed activity level, dirt tolerance, reactor effectiveness, temperature control, and thermal stability of the expanded-bed and moving-bed reactors; residue upgrading in slurry-bed reactors of dispersed vanadium sulfide catalyst in the oil; design and control features for safety and reliability; and a cost comparison between the indirect hydrotreating route, in which the asphalt fraction is separated prior to hydrotreating, and the as yet incompletely developed direct route.

Diamagnetism in spinel compound CuIr2S4

International Nuclear Information System (INIS)

Yagasaki, K.; Nakama, T.

2007-01-01

The diamagnetic susceptibility in CuIr 2 S 4 is independent of temperature up to just below metal-insulator transition temperature. If activation of electrons to higher levels occurs with breaking dimer pairs, the residual electrons at the dimer position and the activated electrons to the anti-bonding orbital make localized free spins giving a Langevin paramagnetism. Assuming no magnetic interaction between the localized free spins, the susceptibility is calculated using the energy gap obtained from the conductivity assumed to be a conventional semiconductor. The calculated results cannot explain the temperature-independent diamagnetism. The real energy gap is too large for thermal electron activation, however, conduction is induced thermally over several orders of magnitude within insulating phase. From the above results, we claimed new conduction mechanism named traveling dimer conduction: dimer shifts its position by electron hopping to neighbor position without electron activation over the energy gap

Residual stress analysis for engineering applications by means of neutron diffraction

International Nuclear Information System (INIS)

Gnaeupel-Herold, T.; Brand, P.C.; Prask, H.J.

1999-01-01

Residual stresses originate from spatial differences in plastic deformation, temperature, or phase distribution, introduced by manufacturing processes or during service. Engineering parts and materials experience mechanical, thermal, and chemical loads during their service, and most of these loads introduce stresses that are superimposed on the already existing residual stresses. Residual stresses can therefore limit or improve life and strength of engineering parts; knowledge and understanding of these stresses is therefore critical for optimizing strength and durability. The economic and scientific importance of neutron diffraction residual stress analysis has led to an increasing number of suitable instruments worldwide. All of the major sources due in the next several years will have instruments for the sole purpose of performing residual stress and texture measurements. Recently, a dedicated, state-of-the-art diffractometer has been installed at the National Institute of Standards and Technology reactor. It has been used for a variety of measurements on basic and engineering stress problems. Among the most prominent examples that have been investigated in collaboration with industrial and academic partners are residual stresses in rails, weldments, and plasma-sprayed coatings

Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings

Science.gov (United States)

Stegemann, Robert; Cabeza, Sandra; Lyamkin, Viktor; Bruno, Giovanni; Pittner, Andreas; Wimpory, Robert; Boin, Mirko; Kreutzbruck, Marc

2017-03-01

The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction (ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth.

Ethanol Basics

Energy Technology Data Exchange (ETDEWEB)

None

2015-01-30

Ethanol is a widely-used, domestically-produced renewable fuel made from corn and other plant materials. More than 96% of gasoline sold in the United States contains ethanol. Learn more about this alternative fuel in the Ethanol Basics Fact Sheet, produced by the U.S. Department of Energy's Clean Cities program.

[Migrants from disposable gloves and residual acrylonitrile].

Science.gov (United States)

Wakui, C; Kawamura, Y; Maitani, T

2001-10-01

Disposable gloves made from polyvinyl chloride with and without di(2-ethylhexyl) phthalate (PVC-DEHP, PVC-NP), polyethylene (PE), natural rubber (NR) and nitrile-butadiene rubber (NBR) were investigated with respect to evaporation residue, migrated metals, migrants and residual acrylonitrile. The evaporation residue found in n-heptane was 870-1,300 ppm from PVC-DEHP and PVC-NP, which was due to the plasticizers. Most of the PE gloves had low evaporation residue levels and migrants, except for the glove designated as antibacterial, which released copper and zinc into 4% acetic acid. For the NR and NBR gloves, the evaporation residue found in 4% acetic acid was 29-180 ppm. They also released over 10 ppm of calcium and 6 ppm of zinc into 4% acetic acid, and 1.68-8.37 ppm of zinc di-ethyldithiocarbamate and zinc di-n-butyldithiocarbamate used as vulcanization accelerators into n-heptane. The acrylonitrile content was 0.40-0.94 ppm in NBR gloves.

New applications of partial residual methodology

International Nuclear Information System (INIS)

Uslu, V.R.

1999-12-01

The formulation of a problem of interest in the framework of a statistical analysis starts with collecting the data, choosing a model, making certain assumptions as described in the basic paradigm by Box (1980). This stage is is called model building. Then the estimation stage is in order by pretending as if the formulation of the problem was true to obtain estimates, to make tests and inferences. In the final stage, called diagnostic checking, checking of whether there are some disagreements between the data and the model fitted is done by using diagnostic measures and diagnostic plots. It is well known that statistical methods perform best under the condition that all assumptions related to the methods are satisfied. However it is true that having the ideal case in practice is very difficult. Diagnostics are therefore becoming important so are diagnostic plots because they provide a immediate assessment. Partial residual plots that are the main interest of the present study are playing the major role among the diagnostic plots in multiple regression analysis. In statistical literature it is admitted that partial residual plots are more useful than ordinary residual plots in detecting outliers, nonconstant variance, and especially discovering curvatures. In this study we consider the partial residual methodology in statistical methods rather than multiple regression. We have shown that for the same purpose as in the multiple regression the use of partial residual plots is possible particularly in autoregressive time series models, transfer function models, linear mixed models and ridge regression. (author)

Effects of recording time and residue on dose-response by LiMgPO4: Tb, B ceramic disc synthesized via improved sintering process

Science.gov (United States)

Kong, Xirui; Fu, Zhilong; Que, Huiying; Fan, Yanwei; Chen, Zhaoyang; He, Chengfa

2018-05-01

The LiMgPO4: Tb, B ceramic disc is successfully synthesized via improved sintering method which enables the disc sample to have two flat and smooth surfaces. It is worth mentioning that the OSL signal intensity of LiMgPO4: Tb, B disc attenuates much faster than that of commercial Al2O3: C. It costs only 1 s to reduce the intensity to 10%, but the Al2O3:C needs more than 40 s to finish it. Some essential OSL properties related to the dose detection method of this sample also have been systematically investigated. Although the dose-response cure would have better linearity with longer recording time, extended recording time (≥6 s) will not make any contribution to the linearity of the curve. If the bleaching time is more than 35 s, the residue created by previous detection (high dose of 10 Gy) would do almost no influence (with a positive deviation lower than 5.59%) on next lower-dose detection (0.1 Gy). The material would reach its service life when the total-ionizing dose runs up to 30 k Gy. Therefore, the LiMgPO4: Tb, B ceramic material is a potential candidate for real-time dose monitoring with optical fiber telemetering technology.

Determination of bromothalonil residues and degradation in apple and soil by QuEChERS and GC-MS/MS.

Science.gov (United States)

Liu, Huijun; Guo, Baoyuan; Wang, Huili; Li, Jianzhong; Zheng, Lin

2014-04-01

The dissipation and residues of bromothalonil in apple and soil under field condition were analyzed by QuEChERS (quick, easy, cheap, effective, rugged and safe) combined with gas chromatography-mass spectrometer method. The recoveries were ranged from 80.8 % to 106 % with coefficient variation for repeatability ranged from 3.08 % to 7.09 % at fortification levels of 0.02, 0.04 and 0.2 mg/kg in apple and soil. The limit of quantification of the method was 0.31 μg/kg. The dissipation rates of bromothalonil followed the first-order kinetics and the half-lives were from 3.61 to 3.98 days in apple and from 4.65 to 9.29 days in soil. In apple, the terminal residues of bromothalonil were below the China maximum residue limit (0.2 mg/kg) after 7 days of application. This work contributed to provide the basic information for a safe usage of bromothalonil in apple orchard and preventing health problem from consumers in China.

Gold nanocatalyst-based immunosensing strategy accompanying catalytic reduction of 4-nitrophenol for sensitive monitoring of chloramphenicol residue.

Science.gov (United States)

Que, Xiaohua; Tang, Dianyong; Xia, Biyun; Lu, Minghua; Tang, Dianping

2014-06-09

A new competitive-type immunosensing system based on gold nanoparticles toward catalytic reduction of 4-nitrophenol (4-NP) was developed for sensitive monitoring of antibiotic residue (chloramphenicol, CAP, used in this case) by using ultraviolet-visible (UV-vis) spectrometry. Gold nanoparticle (AuNP) with 16 nm in diameter was initially synthesized and functionalized with CAP-bovine serum albumin (CAP-BSA) conjugate, which were used as the competitor on monoclonal anti-CAP antibody-coated polystyrene microtiter plate (MTP). In the presence of target CAP, the labeled CAP-BSA on the AuNP competed with target CAP for the immobilized antibody on the MTP. The conjugated amount of CAP-BSA-AuNP on the MTP decreased with the increase of target CAP in the sample. Upon addition of 4-NP and NaBH4 into the MTP, the carried AuNP could catalytically reduce 4-NP to 4-aminophenol (4-AP), and the as-produced 4-AP could be monitored by using UV-vis absorption spectroscopy. Experimental results indicated that the absorbance at 403 nm increased with the increment of target CAP concentration in the sample, and exhibited a dynamic range from 0.1 to 100 ng mL(-1) with a detection limit (LOD) of 0.03 ng mL(-1) at the 3s(blank) level. Intra- and inter-assay coefficients of variation were lower than 5.5% and 8.0%, respectively. In addition, the methodology was evaluated for CAP spiked honey and milk samples, respectively. The recovery was 92-112%. Copyright © 2014. Published by Elsevier B.V.

Thermodynamic effects of replacements of Pro residues in helix interiors of maltose-binding protein.

Science.gov (United States)

Prajapati, R S; Lingaraju, G M; Bacchawat, Kiran; Surolia, Avadhesha; Varadarajan, Raghavan

2003-12-01

Introduction of Pro residues into helix interiors results in protein destabilization. It is currently unclear if the converse substitution (i.e., replacement of Pro residues that naturally occur in helix interiors would be stabilizing). Maltose-binding protein is a large 370-amino acid protein that contains 21 Pro residues. Of these, three nonconserved residues (P48, P133, and P159) occur at helix interiors. Each of the residues was replaced with Ala and Ser. Stabilities were characterized by differential scanning calorimetry (DSC) as a function of pH and by isothermal urea denaturation studies as a function of temperature. The P48S and P48A mutants were found to be marginally more stable than the wild-type protein. In the pH range of 5-9, there is an average increase in T(m) values of P48A and P48S of 0.4 degrees C and 0.2 degrees C, respectively, relative to the wild-type protein. The other mutants are less stable than the wild type. Analysis of the effects of such Pro substitutions in MBP and in three other proteins studied to date suggests that substitutions are more likely to be stabilizing if the carbonyl group i-3 or i-4 to the mutation site is not hydrogen bonded in the wild-type protein. Copyright 2003 Wiley-Liss, Inc.

Potassium phthalimide as efficient basic organocatalyst for the synthesis of 3,4-disubstituted isoxazol-5(4H-ones in aqueous medium

Directory of Open Access Journals (Sweden)

Hamzeh Kiyani

2017-01-01

Full Text Available Potassium phthalimide (PPI is employed as an efficient and effective basic organocatalyst for the one-pot three-component reaction of β-oxoesters with hydroxylamine hydrochloride and various aromatic aldehydes. This cyclocondensation reaction was performed in water as an environmentally benign solvent at room temperature giving 3,4-disubstituted isoxazol-5(4H-ones in good to excellent yields. PPI was found to be an effective organocatalyst for the synthesis of isoxazol-5(4H-one system. The advantages of this method are efficiency, clean, easy work-up, high yields, shorter reaction times, inexpensive, and readily available catalyst.

Inherent dynamics of head domain correlates with ATP-recognition of P2X4 receptors: insights gained from molecular simulations.

Directory of Open Access Journals (Sweden)

Li-Dong Huang

Full Text Available P2X receptors are ATP-gated ion channels involved in many physiological functions, and determination of ATP-recognition (AR of P2X receptors will promote the development of new therapeutic agents for pain, inflammation, bladder dysfunction and osteoporosis. Recent crystal structures of the zebrafish P2X4 (zfP2X4 receptor reveal a large ATP-binding pocket (ABP located at the subunit interface of zfP2X4 receptors, which is occupied by a conspicuous cluster of basic residues to recognize triphosphate moiety of ATP. Using the engineered affinity labeling and molecular modeling, at least three sites (S1, S2 and S3 within ABP have been identified that are able to recognize the adenine ring of ATP, implying the existence of at least three distinct AR modes in ABP. The open crystal structure of zfP2X4 confirms one of three AR modes (named AR1, in which the adenine ring of ATP is buried into site S1 while the triphosphate moiety interacts with clustered basic residues. Why architecture of ABP favors AR1 not the other two AR modes still remains unexplored. Here, we examine the potential role of inherent dynamics of head domain, a domain involved in ABP formation, in AR determinant of P2X4 receptors. In silico docking and binding free energy calculation revealed comparable characters of three distinct AR modes. Inherent dynamics of head domain, especially the downward motion favors the preference of ABP for AR1 rather than AR2 and AR3. Along with the downward motion of head domain, the closing movement of loop139-146 and loop169-183, and structural rearrangements of K70, K72, R298 and R143 enabled ABP to discriminate AR1 from other AR modes. Our observations suggest the essential role of head domain dynamics in determining AR of P2X4 receptors, allowing evaluation of new strategies aimed at developing specific blockers/allosteric modulators by preventing the dynamics of head domain associated with both AR and channel activation of P2X4 receptors.

Analysis of the right-handed Majorana neutrino mass in an S U (4 )×S U (2 )L×S U (2 )R Pati-Salam model with democratic texture

Science.gov (United States)

Yang, Masaki J. S.

2017-03-01

In this paper, we attempt to build a unified model with the democratic texture, that has some unification between up-type Yukawa interactions Yν and Yu . Since the S3 L×S3 R flavor symmetry is chiral, the unified gauge group is assumed to be Pati-Salam type S U (4 )c×S U (2 )L×S U (2 )R. The breaking scheme of the flavor symmetry is considered to be S3 L×S3 R→S2 L×S2 R→0 . In this picture, the four-zero texture is desirable for realistic masses and mixings. This texture is realized by a specific representation for the second breaking of the S3 L×S3 R flavor symmetry. Assuming only renormalizable Yukawa interactions, type-I seesaw mechanism, and neglecting C P phases for simplicity, the right-handed neutrino mass matrix MR can be reconstructed from low energy input values. Numerical analysis shows that the texture of MR basically behaves like the "waterfall texture." Since MR tends to be the "cascade texture" in the democratic texture approach, a model with type-I seesaw and up-type Yukawa unification Yν≃Yu basically requires fine-tunings between parameters. Therefore, it seems to be more realistic to consider universal waterfall textures for both Yf and MR, e.g., by the radiative mass generation or the Froggatt-Nielsen mechanism. Moreover, analysis of eigenvalues shows that the lightest mass eigenvalue MR 1 is too light to achieve successful thermal leptogenesis. Although the resonant leptogenesis might be possible, it also requires fine-tunings of parameters.

Identification of Key Functional Residues in the Active Site of Human β1,4-Galactosyltransferase 7

Science.gov (United States)

Talhaoui, Ibtissam; Bui, Catherine; Oriol, Rafael; Mulliert, Guillermo; Gulberti, Sandrine; Netter, Patrick; Coughtrie, Michael W. H.; Ouzzine, Mohamed; Fournel-Gigleux, Sylvie

2010-01-01

Glycosaminoglycans (GAGs) play a central role in many pathophysiological events, and exogenous xyloside substrates of β1,4-galactosyltransferase 7 (β4GalT7), a major enzyme of GAG biosynthesis, have interesting biomedical applications. To predict functional peptide regions important for substrate binding and activity of human β4GalT7, we conducted a phylogenetic analysis of the β1,4-galactosyltransferase family and generated a molecular model using the x-ray structure of Drosophila β4GalT7-UDP as template. Two evolutionary conserved motifs, 163DVD165 and 221FWGWGREDDE230, are central in the organization of the enzyme active site. This model was challenged by systematic engineering of point mutations, combined with in vitro and ex vivo functional assays. Investigation of the kinetic properties of purified recombinant wild-type β4GalT7 and selected mutants identified Trp224 as a key residue governing both donor and acceptor substrate binding. Our results also suggested the involvement of the canonical carboxylate residue Asp228 acting as general base in the reaction catalyzed by human β4GalT7. Importantly, ex vivo functional tests demonstrated that regulation of GAG synthesis is highly responsive to modification of these key active site amino acids. Interestingly, engineering mutants at position 224 allowed us to modify the affinity and to modulate the specificity of human β4GalT7 toward UDP-sugars and xyloside acceptors. Furthermore, the W224H mutant was able to sustain decorin GAG chain substitution but not GAG synthesis from exogenously added xyloside. Altogether, this study provides novel insight into human β4GalT7 active site functional domains, allowing manipulation of this enzyme critical for the regulation of GAG synthesis. A better understanding of the mechanism underlying GAG assembly paves the way toward GAG-based therapeutics. PMID:20843813

Effect of gamma irradiation and sodium hydroxide on cell wall constituents of some agricultural residues

Energy Technology Data Exchange (ETDEWEB)

Almasri, M R [Department of Radiation Agriculture, Atomic Energy Commision, P.O. Box 6091, Damascus, (Syrian Arab Republic)

1995-10-01

The effect of various doses gamma irradiation and different concentrations of NaOH on cell-wall constituents of wheat straw (W.S), cotton seed shell (C.S.S), peanut shell (P.S), soybean shell (S B.S), extracted olive cake (O.C.E) and extracted sunflower of unpeel seeds (S.U.E) were investigated. Results indicated that Na OH in the concentrations at (2,4 and 6%) had significant effects in the crude fiber (C F) content of W.S, P.S and E.U.E, S B.S, C.S.S, O.C.E,respectively. Treating S.U.E, W.S and all other residues with NaOH (2,4 and 6%) respectively, decreased the neutral-detergent fiber (NDF) level. Irradiation dose of 200 kGy decreased C F for all residues, and it reduced the NDF for S.U.E and S B.S. however, lower irradiation dose (150 KGy) was good enough to reduce the NDF for W.S, C.S.S., P.S. and O.C.E. Combined treatment resulted in better effects in reducing the concentrations of the cell-wall constituents. 3 tabs.

Effect of gamma irradiation and sodium hydroxide on cell wall constituents of some agricultural residues

International Nuclear Information System (INIS)

Almasri, M.R.

1995-01-01

The effect of various doses gamma irradiation and different concentrations of NaOH on cell-wall constituents of wheat straw (W.S), cotton seed shell (C.S.S), peanut shell (P.S), soybean shell (S B.S), extracted olive cake (O.C.E) and extracted sunflower of unpeel seeds (S.U.E) were investigated. Results indicated that Na OH in the concentrations at (2,4 and 6%) had significant effects in the crude fiber (C F) content of W.S, P.S and E.U.E, S B.S, C.S.S, O.C.E,respectively. Treating S.U.E, W.S and all other residues with NaOH (2,4 and 6%) respectively, decreased the neutral-detergent fiber (NDF) level. Irradiation dose of 200 kGy decreased C F for all residues, and it reduced the NDF for S.U.E and S B.S. however, lower irradiation dose (150 KGy) was good enough to reduce the NDF for W.S, C.S.S., P.S. and O.C.E. Combined treatment resulted in better effects in reducing the concentrations of the cell-wall constituents. 3 tabs

Structure-based design of ligands for protein basic domains: Application to the HIV-1 Tat protein

Science.gov (United States)

Filikov, Anton V.; James, Thomas L.

1998-05-01

A methodology has been developed for designing ligands to bind a flexible basic protein domain where the structure of the domain is essentially known. It is based on an empirical binding free energy function developed for highly charged complexes and on Monte Carlo simulations in internal coordinates with both the ligand and the receptor being flexible. HIV-1 encodes a transactivating regulatory protein called Tat. Binding of the basic domain of Tat to TAR RNA is required for efficient transcription of the viral genome. The structure of a biologically active peptide containing the Tat basic RNA-binding domain is available from NMR studies. The goal of the current project is to design a ligand which will bind to that basic domain and potentially inhibit the TAR-Tat interaction. The basic domain contains six arginine and two lysine residues. Our strategy was to design a ligand for arginine first and then a superligand for the basic domain by joining arginine ligands with a linker. Several possible arginine ligands were obtained by searching the Available Chemicals Directory with DOCK 3.5 software. Phytic acid, which can potentially bind multiple arginines, was chosen as a building block for the superligand. Calorimetric binding studies of several compounds to methylguanidine and Arg-/Lys-containing peptides were performed. The data were used to develop an empirical binding free energy function for prediction of affinity of the ligands for the Tat basic domain. Modeling of the conformations of the complexes with both the superligand and the basic domain being flexible has been carried out via Biased Probability Monte Carlo (BPMC) simulations in internal coordinates (ICM 2.6 suite of programs). The simulations used parameters to ensure correct folding, i.e., consistent with the experimental NMR structure of a 25-residue Tat peptide, from a random starting conformation. Superligands for the basic domain were designed by joining together two molecules of phytic acid with

Immobilization of Mn and NH4 (+)-N from electrolytic manganese residue waste.

Science.gov (United States)

Chen, Hongliang; Liu, Renlong; Liu, Zuohua; Shu, Jiancheng; Tao, Changyuan

2016-06-01

The objective of this work was the immobilization of soluble manganese (Mn) and ammonium nitrogen (NH4 (+)-N) leached from electrolytic manganese residue (EMR). Immobilization of Mn was investigated via carbonation using carbon dioxide (CO2) and alkaline additives. NH4 (+)-N immobilization was evaluated via struvite precipitation using magnesium and phosphate sources. Results indicated that the immobilization efficiency of Mn using CO2 and quicklime (CaO) was higher than using CO2 and sodium hydroxide (NaOH). This higher efficiency was likely due to the slower release of OH(-) during CaO hydrolysis. The immobilization efficiency of Mn was >99.99 % at the CaO:EMR mass ratio of 0.05:1 for 20-min reaction time. The struvite precipitation of NH4 (+)-N was conducted in the carbonated EMR slurry and the immobilization efficiency was 89 % using MgCl2 · 6H2O + Na3PO4 · 12H2O at the Mg:P:N molar ratio of 1.5:1.5:1 for 90-min reaction time. A leaching test showed that the concentrations of Mn and NH4 (+)-N in the filtrate of the treated EMR were 0.2 and 9 mg/L, respectively. The combined immobilization of Mn and NH4 (+)-N was an effective pretreatment method in the harmless treatment of the EMR.

CRITIQUES TOWARDS COSO’S ENTERPRISE RISK MANAGEMENT (ERM) FRAMEWORK IN ITS BASIC ASSUMPTIONS

OpenAIRE

Kurniawanti, Ika Atma

2010-01-01

Most professionals in internal control, risk management and other similar bailiwickshave agreed that Enterprise Risk Management discourses would’ve invariablyreferred to what the COSO had produced recently: the framework underlying ERM.But this paper takes a bit different stance that views several problematic issuesstem from unclear conceptions of either the basic premise underlying ERM or thenature of some ERM’s components outlined by COSO. This paper notes that, atleast, there are three poi...

Electron excitation cross sections for the 2s(2)2p(3)4S(O) -- 2s(2)2p(3)2D(O) (forbidden) and 4S(O) -- 2s2p(4) 4P (resonance) transitions in O II

Science.gov (United States)

Zuo, M.; Smith, Steven J.; Chutjian, A.; Williams, I. D.; Tayal, S. S.; Mclaughlin, Brendan M.

1995-01-01

Experimental and theoretical excitation cross sections are reported for the first forbidden transition 4S(O) -- 2S(2)2p(3) 2D(O) (lambda-lambda 3726, 3729) and the first allowed (resonance) transition 4S(O) -- 2s2p(4) 4P(lambda-833) in O II. Use is made of electron energy loss and merged-beams methods. The electron energy range covered is 3.33 (threshold) to 15 eV for the S -- D transition, and 14.9 (threshold) to 40 eV for the S -- P transition. Care was taken to assess and minimize the metastable fraction of the O II beam. An electron mirror was designed and tested to reflect inelastically backscattered electrons into the forward direction to account for the full range of polar scattering angles. Comparisons are made between present experiments and 11-state R-matrix calculations. Calculations are also presented for the 4S(O) -- 2s(2)2p(3)2P(O) (lambda-2470) transition.

Data organisation & description - presentation. RDM Support basic training course for information specialists session 4

OpenAIRE

Selm, Mariette van

2015-01-01

Presentation for session 4 of RDM Support. RDM Support is a basic training course in research data management (support) for information specialists. The training course was developed by Mariëtte van Selm for the information specialists of the Library of the University of Amsterdam (UvA), within the framework of the RDM Support project (2013-2015). The training course was held from January to April 2014.

The effect of motorcycle helmet fit on estimating head impact kinematics from residual liner crush.

Science.gov (United States)

Bonin, Stephanie J; Gardiner, John C; Onar-Thomas, Arzu; Asfour, Shihab S; Siegmund, Gunter P

2017-09-01

Proper helmet fit is important for optimizing head protection during an impact, yet many motorcyclists wear helmets that do not properly fit their heads. The goals of this study are i) to quantify how a mismatch in headform size and motorcycle helmet size affects headform peak acceleration and head injury criteria (HIC), and ii) to determine if peak acceleration, HIC, and impact speed can be estimated from the foam liner's maximum residual crush depth or residual crush volume. Shorty-style helmets (4 sizes of a single model) were tested on instrumented headforms (4 sizes) during linear impacts between 2.0 and 10.5m/s to the forehead region. Helmets were CT scanned to quantify residual crush depth and volume. Separate linear regression models were used to quantify how the response variables (peak acceleration (g), HIC, and impact speed (m/s)) were related to the predictor variables (maximum crush depth (mm), crush volume (cm 3 ), and the difference in circumference between the helmet and headform (cm)). Overall, we found that increasingly oversized helmets reduced peak headform acceleration and HIC for a given impact speed for maximum residual crush depths less than 7.9mm and residual crush volume less than 40cm 3 . Below these levels of residual crush, we found that peak headform acceleration, HIC, and impact speed can be estimated from a helmet's residual crush. Above these crush thresholds, large variations in headform kinematics are present, possibly related to densification of the foam liner during the impact. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tetracycline residues in porcine stomach after administration via drinking water on a swine farm.

Science.gov (United States)

Lindquist, Danielle; Wu, Huali; Mason, Sharon; Yeatts, Jim; Brooks, Jim; Barlow, Beth; Schill, Kaitlyn; Baynes, Ronald

2014-01-01

Tetracycline is a broad-spectrum antibiotic used to treat infections in swine. The maximum residue levels of tetracycline in pork stomach tissue in Russia, Europe, and the United States are 10, 200, and 2,000 ppb, respectively. This difference in accepted safety levels may be the reason why stomach tissues that the United States exports continue to be residue violators in overseas markets. In this study, 30 pigs at two different stages of production (weanling and finisher) were treated with tetracycline at 22 mg/kg of body weight per day for a total of 5 days via a water medicator. Blood samples were collected at 0, 72, 78, 96, and 102 h after the start of medication. The medication was stopped at 120 h, and blood samples were again collected at 126, 144, 168, 192, and 216 h after exposure. Five animals were slaughtered for stomach tissue 0, 24, 48, 96, and 192 h after the drug was flushed from the water line. All blood and tissue samples were analyzed by high-performance liquid chromatography-UV methods. The tetracycline levels in plasma were below the level of detection after the U.S.-labeled withdrawal time of 4 days. The stomach tissue residues averaged 671.72, 330.31, 297.77, 136.36, and 268.08 ppb on withdrawal days 0, 1, 2, 4, and 8, respectively. Using the U.S. Food and Drug Administration tolerance limit method and a population-based pharmacokinetic model with Monte Carlo simulation, a withdrawal interval was estimated. This study demonstrated that tetracycline residues are still detectable in the stomach tissues after the established United States withdrawal time of 4 days. These residue levels may explain why stomach tissues tested in Russia and Europe show positive residues for tetracycline, even though the meat may pass inspection here in the United States prior to export.

Recuperación de sílice residual de columnas de cromatografía en la síntesis sol-gel de pigmentos

Directory of Open Access Journals (Sweden)

Grañana, M. C.

2000-04-01

Full Text Available The use of a silica waste of support chromatography process as raw material in the synthesis of ceramic pigments based in zircon network (yellow of praseodymium, turkish blue of vanadium and pink koral of iron, is analized in this study. The synthesis has been carried out by ceramic method and also by colloidal sol-gel and coprecipitation routes. Silica waste becomes an effective precursor in the zircon ceramic stains. Likewise, the high temperature and long soaking time used in the synthesis ensure the whole combustion of adsorbed organics on the waste.

En este trabajo se caracteriza una sílice residual de procesos de cromatografía de columna y se analiza su utilización como precursor en la síntesis de los tres pigmentos triaxiales del circón (amarillo de praseodimio, turquesa de vanadio y coral de hierro utilizando tanto la vía sol-gel coloidal, la coprecipitación y el método cerámico. La sílice residual se muestra como un precursor muy efectivo en la obtención de los colores del circón tanto vía cerámica como a partir de geles. La alta temperatura así como los relativamente largos periodos de retención utilizados en la síntesis de los pigmentos cerámicos, permite una total combustión de los orgánicos adsorbidos sobre la sílice.

A new method of residual stress distribution analysis for corroded Zircaloy-4 cladding

International Nuclear Information System (INIS)

Godlewski, J.; Cadalbert, R.

1992-01-01

An X-ray diffraction method of residual stress measurement is developed to determine the stress level in the metal near the metal/oxide interface of Zircaloy-4 cladding samples oxidized in steam water at 400degC under a pressure of 10.3 MPa. The stress gradient is obtained and the evolution of the average stress is determined as function of the oxidation time. The presence of tetragonal zirconia phase in quite large quantity near the metal/oxide interface could be correlated to the high stress level in the base metal, adjacent to the interface. (author)

A new method for residual stress distribution - analysis of corroded zircaloy-4 cladding

International Nuclear Information System (INIS)

Godlewski, J.; Cadalbert, R.

1992-01-01

An X-ray diffraction method for residual stress measurement is developed to determine the stress level in the metal near the metal/oxide interface of Zircaloy-4 cladding samples oxidized in steam water at 400 deg C under a pressure of 10.3 MPa. The stress gradient is obtained and the evolution of the average stress is determined as a function of the oxidation time. The presence of tetragonal zirconia phase in quite large quantity near the metal/oxide interface could be correlated to the high stress level in the base metal, adjacent to the interface. 12 refs., 5 figs., 1 tab

Efeito residual de sulfentrazone, isoxaflutole e oxyfluorfen em três solos Residual effect of sulfentrazone, isoxaflutole and oxyfluorfen in three soils

Directory of Open Access Journals (Sweden)

C.A.D Melo

2010-12-01

Full Text Available As características físicas e químicas do solo, além das condições climáticas, influenciam o comportamento de herbicidas aplicados em pré-emergência das plantas daninhas. Dessa forma, objetivou-se avaliar o efeito residual de sulfentrazone, isoxaflutole e oxyfluorfen em três solos. O ensaio foi conduzido em ambiente protegido e o delineamento experimental foi em blocos casualizados, com quatro repetições. Os tratamentos, para cada solo, foram dispostos em esquema fatorial 3 x 5, sendo três herbicidas e cinco épocas de semeadura após aplicação dos produtos. Os herbicidas sulfentrazone, oxyfluorfen e isoxaflutole foram aplicados nas doses de 0,5, 0,72 e 0,113 kg ha-1, respectivamente, sobre potes plásticos de 250 mL previamente preenchidos com os dois solos de textura argilosa e um de textura franco-arenosa. Posteriormente, procedeu-se à semeadura da espécie bioindicadora Sorghum bicolor de forma escalonada, aos 0, 15, 30, 45 e 60 dias após a aplicação (DAA. Uma testemunha sem herbicida foi semeada nas diferentes épocas para cada solo e usada como comparação nas avaliações. Aos 21 dias após a semeadura em cada época, realizaram-se avaliações de intoxicação e crescimento das plantas através da massa seca da parte aérea. As plantas de sorgo, no solo argiloso com 9,0 dag kg-1 de matéria orgânica (MO submetido à aplicação de isoxaflutole, sulfentrazone e oxyfluorfen, produziram massa seca da parte aérea igual a 34, 20 e 40%, respectivamente, aos 60 DAA, em relação às plantas crescidas nesse solo sem aplicação do herbicida. No solo franco-arenoso, observou-se elevado efeito residual dos herbicidas sulfentrazone e oxyfluorfen e diminuição do efeito residual do isoxaflutole ao longo do tempo, com 80, 90 e 40% de controle aos 60 DAA, respectivamente. No solo argiloso com 4,4 dag kg-1 de MO, verificou-se que o herbicida isoxaflutole perdeu a eficácia de controle ao longo do tempo, diferentemente do

Qualidade de águas residuárias e salobra utilizadas no cultivo hidropônico de três cultivares de alface crespa

Directory of Open Access Journals (Sweden)

José Emídio de Albuquerque Júnior

2016-04-01

Full Text Available O reúso de efluentes tratados não é uma prática nova, no entanto, há um interesse crescente em relação à necessidade de sua reutilização. Objetivou-se avaliar a caraterização das águas residuárias domestica e do reator UASB e água salobra de poço para o cultivo hidropônico de alface crespa. O experimento foi conduzido em ambiente protegido com sistema hidropônico. Delineamento experimental foi em blocos casualizados com esquema fatorial 7 x 3, três repetições sendo, 7 soluções hidropônicase três cultivares de alface. A parcela experimental, S1=solução de Furlani; S2=água residuária domestica; S3=água residuária domestica otimizada; S4=água de poço; S5=água de poço otimizada; S6=água residuária (UASB e S7=água residuária (UASB otimizada, subparcela três cultivares de alface. O pH das águas residuárias foram de 7,7 e 7,4 (Poço; 7,4 e 8,0 (Esgoto bruto e, 7,2 e 8,2 (Extrabes. A (CE foram 0,957 e 1,002 (Poço; 2,133 e 2,368 (Esgoto bruto e (Extrabes 2,502 e 2,4 09 dS m-1. O uso de soluções minerais nutritivas utilizando água residuária é viável quando utilizado em sistemas hidropônicos, sendo indicado para principalmente para região do semiárido brasileiro e quando se faz uso de água de irrigação de qualidade inferior na produção de hortaliças.Quality of wastewater and brackish water used in the hydroponic cultivation of three varieties of curly lettuce Abstract: The reuse of treated wastewater is not a new practice, however, there is a growing interest in the need for re-use. The objective was to evaluate the Characterisation of domestic wastewater and UASB and brackish well for hydroponic lettuce. The experiment was conducted in a protected environment with hydroponically. Experimental design was a randomized block with factorial 7 x 3, three replications and 7 hydroponic solutions and three lettuce cultivars. The experimental portion, S1 = Furlani solution; S2 = domestic wastewater; S3

Walisongo’s Educational Leadership through Modelling and Fulfilment of Human Basic Needs

Directory of Open Access Journals (Sweden)

Nanang Hasan Susanto

2017-12-01

Full Text Available This study aims to trace the Walisongo’s (the Nine Saints leadership model that is often considered successful in Islamizing the Javanese community in a relatively short time and almost without conflict. Through the literature search using analytic descriptive, this study brings the conclusion that based on the conventional leadership model division, the Walisongo’s leadership can be categorized into transformational leadership with characteristics capable of fostering the trust, pride, loyalty and respect of Javanese society. In addition, the Walisongo's leadership also conforms to the characteristics proposed by Tobroni, which include spiritual leadership, with characteristics based on the divine aspect, done with honesty and sincerely, drawing public sympathy and mobilizing them to follow the Walisongo’s teachings. This research also produces a finding that the success of Walisongo in educating the people of Java is due to their concern on the efforts to meet the basic needs of the society and provide models to follow.

Joining U.S. NRC international round robin for weld residual stress analysis. Stress analysis and validation in PWSCC mitigation program

International Nuclear Information System (INIS)

Maekawa, Akira; Serizawa, Hisashi; Murakawa, Hidekazu

2012-01-01

It is necessary to establish properly reliable weld residual stress analysis methods for accurate crack initiation and growth assessment of primary water stress corrosion cracking (PWSCC), which may occur in nickel-based dissimilar metal welds in pressurized water reactors. The U.S. Nuclear Regulatory Commission conducted an international round robin for weld residual stress analysis to improve stress analysis methods and to examine the uncertainties involved in the calculated stress values. In this paper, the results from the authors' participation in the round robin were reported. In the round robin, the weld residual stress in a nickel-based dissimilar metal weld of a pressurizer surge nozzle mock-up was computed under various analysis conditions. Based on these residual stress analysis results, a welding simulation code currently being developed that uses the iterative substructure method was validated and affecting factors on the analysis results were identified. (author)

Calculation of the total electron excitation cross section in the Born approximation using Slater wave functions for the Li (2s yields 2p), Li (2s yields 3p), Na (3s yields 4p), Mg (3p yields 4s), Ca (4s yields 4p) and K (4s yields 4p) excitations. M.S. Thesis

Science.gov (United States)

Simsic, P. L.

1974-01-01

Excitation of neutral atoms by inelastic scattering of incident electrons in gaseous nebulae were investigated using Slater Wave functions to describe the initial and final states of the atom. Total cross sections using the Born Approximation are calculated for: Li(2s yields 2p), Na(3s yields 4p), k(4s yields 4p). The intensity of emitted radiation from gaseous nebulae is also calculated, and Maxwell distribution is employed to average the kinetic energy of electrons.

Basic numerical study on gap influence of residual stress and distortion during high-brightness laser butt welding

International Nuclear Information System (INIS)

Serizawa, Hisashi; Mori, Daiki; Murakawa, Hidekazu

2013-01-01

High-brightness laser such as fiber laser or disk laser is expected to minimize the total heat input energy in welding due to its high beam quality, and the welding residual stress and distortion also seem to be reduced as a result. However, the diameter of high-brightness laser beam is less than 0.6 mm and it is difficult to set the beam position to contact face between two parts because in general there would be a gap due to quality of parts. In this study, in order to reveal the effect of gap on the residual stress and the welding distortion during fiber laser welding, the butt welding of two plates were examined through the thermal elastic-plastic analysis with a new gap element. From the result of thermal analyses, it was found that the homogeneous ellipsoid body could be applicable to model the shape of heat source for the fiber laser and the gap width would not influence the penetration shape when the gap width was changed from 0.1 to 0.25 mm. In addition, the elastic-plastic analyses indicated that the transverse shrinkage slightly increased with increasing the gap width, while this shrinkage without gap was much smaller than that with gap. Also, it was revealed that the welding speed largely affects both the welding residual stress and distortion. Moreover, it was found that the residual stress was almost independent of the jig position, while the position of fixtures slightly affected the transverse shrinkage. (author)

The Effect of Creep on the Residual Stresses Generated During Silicon Sheet Growth

Science.gov (United States)

Hutchinson, J. W.; Lambropoulos, J. C.

1984-01-01

The modeling of stresses generated during the growth of thin silicon sheets at high speeds is an important part of the EFG technique since the experimental measurement of the stresses is difficult and prohibitive. The residual stresses which arise in such a growth process lead to serious problems which make thin Si ribbons unsuitable for fabrication. The constitutive behavior is unrealistic because at high temperature (close to the melting point) Si exhibits considerable creep which significantly relaxes the residual stresses. The effect of creep on the residual stresses generated during the growth of Si sheets at high speeds was addressed and the basic qualitative effect of creep are reported.

Residual nilpotence and residual solubility of groups

International Nuclear Information System (INIS)

Mikhailov, R V

2005-01-01

The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

A review of some basic aspects related to integration of airplane’s equations of motion

Directory of Open Access Journals (Sweden)

Dan TURCANU

2017-09-01

Full Text Available Numerical integration of the airplane’s equations of motion has long been considered among the most fundamental calculations in airplane’s analysis. Numerical algorithms have been implemented and experimentally validated. However, the need for superior speed and accuracy is still very topical, as, nowadays, various optimization algorithms rely heavily on data generated from the integration of the equations of motion and having access to larger amounts of data can increase the quality of the optimization. Now, for a number of decades, engineers have relied heavily on commercial codes based on automatically selected integration steps. However, optimally chosen constant integration steps can save time and allows for larger numbers of integrations to be performed. Yet, the basic papers that presented the fundamentals of numerical integration, as applied to airplane’s equations of motion are nowadays not easy to locate. Consequently, this paper presents a review of basic aspects related to the integration of airplane’s equation of motion. The discussion covers fundamentals of longitudinal and lateral-directional motion as well as the implementation of some numerical integration methods. The relation between numerical integration steps, accuracy, computational resource usage, numerical stability and their relation with the parameters describing the dynamic response of the airplane is considered and suggestions are presented for a faster yet accurate numerical integration.

Physicochemical basics for production of uranium concentrate from wastes of hydrometallurgical plants and technical waters

International Nuclear Information System (INIS)

Khakimov, N.; Nazarov, Kh.M.; Khojiyon, M.; Mirsaidov, I.U.; Nazarov, K.M.; Barotov, B.B.

2012-01-01

Physicochemical and technological basics for reprocessing of uranium industry wastes of Northern Tajikistan shows that the most perspective for reprocessing is Chkalovsk tailing's wastes. Engineer and geological condition and content of radionuclides in wastes are investigated. It is determined that considered wastes by radioactivity are low-active and they can be reprocessed with the purpose of U 3 O 8 production. Grinding, crumbling, thickening and etc. operations are decreased during the wastes reprocessing process. Uranium output is more than 90%. Optimal parameters of products extraction from uranium mining industry wastes are found. Characteristics of mine and technical waters of uranium industry wastes are studied. Characteristics of mine and technical waters of Kiik-Tal and Istiklol city (former Taboshar) showed the expediency of uranium oxide extraction from them. The reasons for non-additional recovery extraction from dumps of State Enterprise 'Vostokredmet' by classical methods of uranium leaching are studied. Kinetics of sulfuric leaching of residues from anthropogenic deposit of Map 1-9 (Chkalovsk city) is investigated. Carried out investigations are revealing the flow mechanism process of residues' sulfuric leaching and enable selection of radiation regime of U 3 O 8 production. Kinetics of sorption process of uranium extraction from mine and technical waters of uranium industry wastes is studied. High sorption properties of apricot's shell comparing to other sorbents are revealed. Basic process flow diagram for reprocessing of uranium tailing wastes is developed as well as diagram for uranium extraction from mine and technical waters from uranium industry wastes which consists of the following stages: acidification, sorption, burning, leaching, sedimentation, filtration, drying.

Feline Immunodeficiency Virus Vif N-Terminal Residues Selectively Counteract Feline APOBEC3s.

Science.gov (United States)

Gu, Qinyong; Zhang, Zeli; Cano Ortiz, Lucía; Franco, Ana Cláudia; Häussinger, Dieter; Münk, Carsten

2016-12-01

Feline immunodeficiency virus (FIV) Vif protein counteracts feline APOBEC3s (FcaA3s) restriction factors by inducing their proteasomal degradation. The functional domains in FIV Vif for interaction with FcaA3s are poorly understood. Here, we have identified several motifs in FIV Vif that are important for selective degradation of different FcaA3s. Cats (Felis catus) express three types of A3s: single-domain A3Z2, single-domain A3Z3, and double-domain A3Z2Z3. We proposed that FIV Vif would selectively interact with the Z2 and the Z3 A3s. Indeed, we identified two N-terminal Vif motifs (12LF13 and 18GG19) that specifically interacted with the FcaA3Z2 protein but not with A3Z3. In contrast, the exclusive degradation of FcaA3Z3 was regulated by a region of three residues (M24, L25, and I27). Only a FIV Vif carrying a combination of mutations from both interaction sites lost the capacity to degrade and counteract FcaA3Z2Z3. However, alterations in the specific A3s interaction sites did not affect the cellular localization of the FIV Vif protein and binding to feline A3s. Pulldown experiments demonstrated that the A3 binding region localized to FIV Vif residues 50 to 80, outside the specific A3 interaction domain. Finally, we found that the Vif sites specific to individual A3s are conserved in several FIV lineages of domestic cat and nondomestic cats, while being absent in the FIV Vif of pumas. Our data support a complex model of multiple Vif-A3 interactions in which the specific region for selective A3 counteraction is discrete from a general A3 binding domain. Both human immunodeficiency virus (HIV) and feline immunodeficiency virus (FIV) Vif proteins counteract their host's APOBEC3 restriction factors. However, these two Vif proteins have limited sequence homology. The molecular interaction between FIV Vif and feline APOBEC3s are not well understood. Here, we identified N-terminal FIV Vif sites that regulate the selective interaction of Vif with either feline APOBEC3Z

Nuclear AP4A-binding activity of sea urchin embryos changes in relation to the initiation of S phase

International Nuclear Information System (INIS)

Morioka, M.; Shimada, H.

1986-01-01

The AP 4 A-binding activity of sea urchin embryos was studied using radioactively labelled diadenosine 5', 5'''-P 1 ,P 4 -tetraphosphate (Ap 4 A). Among various subcellular components that can bind [ 3 H]AP 4 A, nuclei alone showed the highly specific Ap 4 A-binding activity which was not influenced by the presence of AP 4 A, AP 5 A and GP 4 G. The addition of an excess amount of ATP only slightly reduced the binding of [ 3 H]AP 4 A to the nuclei. It was found that AP 4 A binds to the residual proteinaceous structure of nuclei which was resistant to the extraction with 2 M NaCl. The nuclear AP 4 A-binding activity fluctuated cyclically during each cell cycle, with at transient increase at the beginning of S phase followed by an abrupt-decrease within 10 min. When the initiation of S phase was blocked, the increase in the AP 4 A-binding activity was also prevented. It seems that the binding of AP 4 A to the nuclear structural protein is involved in the initiation of S phase

N4H9Cu7S4: a hydrazinium-based salt with a layered Cu7S4- framework.

Science.gov (United States)

Mitzi, David B

2007-02-05

Crystals of a hydrazinium-based copper(I) sulfide salt, N4H9Cu7S4 (1), have been isolated by an ambient temperature solution-based process. In contrast to previously reported hydrazinium salts of main-group metal chalcogenides, which consist of isolated metal chalcogenide anions, and ACu7S4 (A = NH4+, Rb+, Tl+, K+), which contains a more three-dimensional Cu7S4- framework with partial Cu-site occupancy, the structure of 1 [P21, a = 6.8621(4) A, b = 7.9851(4) A, c = 10.0983(5) A, beta = 99.360(1) degrees , Z = 2] is composed of extended two-dimensional Cu7S4- slabs with full Cu-site occupancy. The Cu7S4- slabs are separated by a mixture of hydrazinium and hydrazine moieties. Thermal decomposition of 1 into copper(I) sulfide proceeds at a significantly lower temperature than that observed for analogous hydrazinium salts of previously considered metal chalcogenides, completing the transition at temperatures as low as 120 degrees C. Solutions of 1 may be used in the solution deposition of a range of Cu-containing chalcogenide films.

Introduction to the AdS/CFT Correspondence

Science.gov (United States)

Nąstase, Horaǧiu

2015-09-01

Preface; Introduction; Part I. Background: 1. Elements of quantum field theory and gauge theory; 2. Basics of general relativity. Anti-de Sitter space; 3. Basics of supersymmetry; 4. Basics of supergravity; 5. Kaluza-Klein dimensional reduction; 6. Black holes and p-branes; 7. String theory actions and spectra; 8. Elements of conformal field theory; 9. D-branes; Part II. Basics of AdS/CFT for N = 4 SYM vs AdS5 × S5: 10. The AdS/CFT correspondence: motivation, definition and spectra; 11. Witten prescription and 3-point correlator calculations; 12. Holography in Lorentzian signature: Poincaré and global; 13. Solitonic objects in AdS/CFT; 14. Quarks and the Wilson loop; 15. Finite temperature and N = 4 SYM plasmas; 16. Scattering processes and gravitational shockwave limit; 17. The pp-wave correspondence; 18. Spin chains; Part III. AdS/CFT Developments and Gauge-Gravity Dualities: 19. Other conformal cases; 20. The 3 dimensional ABJM model vs. AdS4 × CP3; 21. Gravity duals; 22. Holographic renormalization; 23. RG flow between fixed points; 24. Phenomenological gauge-gravity duality I: AdS/QCD; 25. Phenomenological gauge-gravity duality II: AdS/CMT; 26. Gluon scattering: the Alday-Maldacena prescription; 27. Holographic entanglement entropy: the Ryu-Takayanagi prescription.

Evaluation of Cement, Lime, and Asphalt Amended Municipal Solid Waste Incinerator Residues

Science.gov (United States)

1989-09-01

the lime column over time ( Atlas & Bartha , 1987). Certainly, a more extensive evaluation of the lime amended residue’s microbial activity is required...4.02 ASTM D 1559 (1988) Annual Book of ASTM Standards: Road & Paving Materials; Traveled Surface Characteristics, Sec 4, Vol 4.03 Atlas , R. & R. Bartha ...1987) Microbial Ecology : Fundamentals & Applications, Benjamin-Cummings, Menlo, CA Barrow N., J. Bowden, A. Posner, & J. Quirk (1981) Describing the

S100B-immunopositive glia is elevated in paranoid as compared to residual schizophrenia: a morphometric study.

Science.gov (United States)

Steiner, Johann; Bernstein, Hans-Gert; Bielau, Hendrik; Farkas, Nadine; Winter, Jana; Dobrowolny, Henrik; Brisch, Ralf; Gos, Tomasz; Mawrin, Christian; Myint, Aye Mu; Bogerts, Bernhard

2008-08-01

Several studies have revealed increased S100B levels in peripheral blood and cerebrospinal fluid (CSF) of patients with schizophrenia. In this context, it was postulated that elevated levels of S100B may indicate changes of pathophysiological significance to brain tissue in general and astrocytes in particular. However, no histological study has been published on the cellular distribution of S100B in the brain of individuals with schizophrenia to clarify this hypothesis. The cell-density of S100B-immunopositive glia was analyzed in the anterior cingulate, dorsolateral prefrontal (DLPF), orbitofrontal, and superior temporal cortices/adjacent white matter, pyramidal layer/alveus of the hippocampus, and the mediodorsal thalamic nucleus of 18 patients with schizophrenia and 16 matched control subjects. Cortical brain regions contained more S100B-immunopositive glia in the schizophrenia group relative to controls (P=0.046). This effect was caused by the paranoid schizophrenia subgroup (P=0.018). Separate analysis of white matter revealed no diagnostic main group effect (P=0.846). However, the white matter of patients with paranoid schizophrenia contained more (mainly oligodendrocytic) S100B-positive glia as compared to residual schizophrenia (P=0.021). These effects were particularly pronounced in the DLPF brain area. Our study reveals distinct histological patterns of S100B immunoeactive glia in two schizophrenia subtypes. This may be indicative of a heterogenic pathophysiology or distinct compensatory abilities: Astro-/oligodendroglial activation may result in increased cellular S100B in paranoid schizophrenia. On the contrary, residual schizophrenia may be caused by white matter oligodendroglial damage or dysfunction, associated with a release of S100B into body fluids.

Tungsten phosphanylarylthiolato complexes [W{PhP(2-SC6H4)2-kappa3S,S',P} 2] and [W{P(2-SC6H4)3-kappa4S,S',S",P}2]: synthesis, structures and redox chemistry.

Science.gov (United States)

Hildebrand, Alexandra; Lönnecke, Peter; Silaghi-Dumitrescu, Luminita; Hey-Hawkins, Evamarie

2008-09-14

PhP(2-SHC6H4)2 (PS2H2) reacts with WCl6 with reduction of tungsten to give the air-sensitive tungsten(IV) complex [W{PhP(2-SC6H4)2-kappa(3)S,S',P}2] (1). 1 is oxidised in air to [WO{PhPO(2-SC6H4)2-kappa(3)S,S',O}{PhP(2-SC6H4)2-kappa(3)S,S',P}] (2). The attempted synthesis of 2 by reaction of 1 with iodosobenzene as oxidising agent was unsuccessful. [W{P(2-SC6H4)3-kappa(4)S,S',S",P}2] (3) was formed in the reaction of P(2-SHC6H4)3 (PS3H3) with WCl6. The W(VI) complex 3 contains two PS3(3-) ligands, each coordinated in a tetradentate fashion resulting in a tungsten coordination number of eight. The reaction of 3 with AgBF4 yields the dinuclear tungsten complex [W2{P(2-SC6H4)3-kappa(4)S,S',S",P}3]BF4 (4). Complexes 1-4 were characterised by spectral methods and X-ray structure determination.

Residual power series method for fractional Sharma-Tasso-Olever equation

Directory of Open Access Journals (Sweden)

Amit Kumar

2016-02-01

Full Text Available In this paper, we introduce a modified analytical approximate technique to obtain solution of time fractional Sharma-Tasso-Olever equation. First, we present an alternative framework of the Residual power series method (RPSM which can be used simply and effectively to handle nonlinear fractional differential equations arising in several physical phenomena. This method is basically based on the generalized Taylor series formula and residual error function. A good result is found between our solution and the given solution. It is shown that the proposed method is reliable, efficient and easy to implement on all kinds of fractional nonlinear problems arising in science and technology.

Depletion of isoeugenol residues from the fillet tissue of AQUI-S™ exposed rainbow trout (Oncorhynchus mykiss)

Science.gov (United States)

Meinertz, Jeffery R.; Schreier, Theresa M.

2009-01-01

There is a critical need in U.S. public aquaculture and fishery management for an approved sedative that allows for the immediate release of fish after sedation. AQUI-STM is a fish anesthetic/sedative approved for use in several countries and until recently was being developed in the U.S. as a sedative for immediate release of fish after sedation. The U.S. National Toxicology Program reported that isoeugenol (the active ingredient in AQUI-STM) exposed male mice showed clear evidence of carcinogenicity, therefore efforts within the U.S. Department of Interior to develop AQUI-STM as a sedative that allows for immediate release ceased. Despite the ruling, AQUI-STM still has the potential to be approved as an anesthetic with a short withdrawal time. Among the data required to gain approval for use in the U.S. are data describing the composition and depletion of all AQUI-STM residues from fish fillet tissue. A total residue depletion study for AQUI-STM was conducted by exposing market-sized rainbow trout, Oncorhynchus mykiss (mean weight, 502.7 ± 54 g; s.d.) to 8.9 mg/L of 14C-[URL]-isoeugenol for 60 min in 17 °C water. The 14C-[URL]-isoeugenol was mixed with a surfactant resulting in a mixture that mimicked AQUI-STM. Groups of fish (n = 6) were sampled immediately after the exposure (0-h sample group) and at 0.5, 1, 2, and 4 h thereafter. Total isoeugenol-equivalent residue concentrations in the fillet tissue were determined by oxidizing triplicate subsamples of homogenized skin-on fillet tissue from each fish to 14CO2 and enumerating the radioactivity by static liquid scintillation counting. Isoeugenol concentrations in fillet tissue were determined by extracting homogenized fillet tissue with solvents and determining the isoeugenol concentrations in the extracts with high performance liquid chromatography techniques. The mean total isoeugenol-equivalent residue concentrations in the 0, 0.5, 1, 2, and 4-h sample groups were 55.4, 32.0, 19.8, 11

Estima de error residual explícita para cantidades de interés utilizando funciones burbuja

OpenAIRE

Rosales, R.; Díez, P.

2009-01-01

En este trabajo se introduce un nuevo estimador de error residual explícito a posteriori para problemas elípticos orientado a cantidades de interés. Se propone utilizar funciones burbuja sobre elementos y sobre aristas. Se parte de la solución de elementos finitos del problema primal y de la de un problema junto (o dual), asociado a una cantidad de interés definida por el usuario. Por ejemplo, la variación de temperatura o el desplazamiento de un punto del dominio. La estima se calcula en...

Residual symptoms and functioning in depression, does the type of residual symptom matter? A post-hoc analysis

Directory of Open Access Journals (Sweden)

Romera Irene

2013-02-01

Full Text Available Abstract Background The degrees to which residual symptoms in major depressive disorder (MDD adversely affect patient functioning is not known. This post-hoc analysis explored the association between different residual symptoms and patient functioning. Methods Patients with MDD who responded (≥50% on the 17-item Hamilton Rating Scale for Depression; HAMD-17 after 3 months of treatment (624/930 were included. Residual core mood-symptoms (HAMD-17 core symptom subscale ≥1, residual insomnia-symptoms (HAMD-17 sleep subscale ≥1, residual anxiety-symptoms (HAMD-17-anxiety subscale ≥1, residual somatic-symptoms (HAMD-17 Item 13 ≥1, pain (Visual Analogue Scale ≥30, and functioning were assessed after 3 months treatment. A stepwise logistic regression model with normal functioning (Social and Occupational Functioning Assessment Scale ≥80 as the dependent variable was used. Results After 3 months, 59.5% of patients (371/624 achieved normal functioning and 66.0% (412/624 were in remission. Residual symptom prevalence was: core mood symptoms 72%; insomnia 63%; anxiety 78%; and somatic symptoms 41%. Pain reported in 18%. Factors associated with normal functioning were absence of core mood symptoms (odds ratio [OR] 8.7; 95% confidence interval [CI], 4.6–16.7, absence of insomnia symptoms (OR 1.8; 95% CI, 1.2–2.7, episode length (4–24 weeks vs. ≥24 weeks [OR 2.0; 95% CI, 1.1–3.6] and better baseline functioning (OR 1.0; 95% CI, 1.0–1.1. A significant interaction between residual anxiety symptoms and pain was found (p = 0.0080. Conclusions Different residual symptoms are associated to different degrees with patient functioning. To achieve normal functioning, specific residual symptoms domains might be targeted for treatment.

Bottled Water Basics

Science.gov (United States)

Table of Contents Bottled water basics ....................................... pg.2 Advice for people with severely compromised immune systems (Sidebar) ............................. pg2 Know what you’re buying .............................. pg.3 Taste considerations ........................................ pg.4 Bottled water terms (Sidebar) ..................... pg.4 Begin by reading the ...

Identification of a highly reactive threonine residue at the active site of γ-glutamyl transpeptidase

International Nuclear Information System (INIS)

Stole, E.; Seddon, A.P.; Wellner, D.; Meister, A.

1990-01-01

γ-Glutamyl transpeptidase an enzyme of major importance in glutathione metabolism, was inactivated by treating it with L-(αS,5S)-α-amino-3-chloro-4,5-dihydro-5-[3- 14 C]isoxazoleacetic acid. This selective reagent binds stoichiometrically to the enzyme; more than 90% of the label was bound to its light subunit. Enzymatic digestion of the light subunit gave a 14 C-labeled peptide that corresponds to amino acid residues 517-527 of the enzyme and two incomplete digestion products that contain this labeled peptide moiety. The radioactivity associated with this peptide was released with threonine-523 during sequencing by the automated gas-phase Edman method. The light subunit contains 14 other threonine residues and a total of 19 serine residues; these were not labeled. Threonine-523 is situated in the enzyme in an environment that greatly increases its reactivity, indicating that other amino acid residues of the enzyme must also participate in the active-site chemistry of the enzyme

Microwave calcination for plutonium immobilization and residue stabilization

Energy Technology Data Exchange (ETDEWEB)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S. [Kaiser-Hill Co., Golden, CO (United States)

1995-12-01

In the late 1980`s development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96.

Microwave calcination for plutonium immobilization and residue stabilization

International Nuclear Information System (INIS)

Harris, M.J.; Rising, T.L.; Roushey, W.J.; Sprenger, G.S.

1995-01-01

In the late 1980's development was begun on a process using microwave energy to vitrify low level mixed waste sludge and transuranic mixed waste sludge generated in Building 374 at Rocky Flats. This process was shown to produce a dense, highly durable waste form. With the cessation of weapons production at Rocky Flats, the emphasis has changed from treatment of low level and TRU wastes to stabilizaiton of plutonium oxide and residues. This equipment is versatile and can be used as a heat source to calcine, react or vitrify many types of residues and oxides. It has natural economies in that it heats only the material to be treated, significantly reducing cycle times over conventional furnaces. It is inexpensive to operate in that most of the working components remain outside of any necessary contamination enclosure and therefore can easily be maintained. Limited testing has been successfully performed on cerium oxide (as a surrogate for plutonium oxide), surrogate electrorefining salts, surrogate residue sludge and residue ash. Future plans also include tests on ion exchange resins. In an attempt to further the usefullness of this technology, a mobile, self-contained microwave melting system is currently under development and expected to be operational at Rocky Flats Enviromental Technology Site by the 4th quarter of FY96

Quantitative determination of residual 1,4-dioxane in three-dimensional printed bone scaffold

Directory of Open Access Journals (Sweden)

Ling Li

2018-04-01

Full Text Available Summary: Background/Objective: A novel porous scaffold poly (lactide-co-glycolide and tricalcium phosphate (PLGA/TCP was developed by three-dimensional printing technology for bone defect repair. As a Class 2 solvent with less severe toxicity, content of residual 1,4-dioxane in this newly developed scaffold should be rigorously controlled when it is translated to clinical use. In this study, a headspace gas chromatography-mass spectrometric (HS-GC-MS method and related testing protocol were developed for quantitative determination of 1,4-dioxane in the PLGA/TCP composite scaffolds. Methods: Matrix effect analysis was used to optimise the pretreatment method of the scaffolds. Then, the procedure for testing 1,4-dioxane using HS-GC-MS was set up. The accuracy, precision, and robustness of this newly developed quantitative method were also validated before quantification of 1,4-dioxane in the scaffolds with different drying procedures. Results: Dimethyl formamide (DMF was the optimal solvent for dissolving scaffolds for GC-MS with proper sensitivity and without matrix effect. Then, the optimised procedure was determined as: the scaffolds were dissolved in DMF and kept at 90°C for 40 minutes, separated on a HP-5MS column, and detected by mass spectroscopy. Recovery experiments gave 97.9–100.7% recovery for 1,4-dioxane. The linear range for 1,4-dioxane was determined as 1–40 ppm with linear correlation coefficient ≥ 0.9999. Intraday and interday precision was determined as being within relative standard deviation of below 0.68%. The passable drying procedure was related to lyophilising (−50°C, 50 Pa the scaffolds for 2 days and drying in vacuum (50 Pa for 7 days. Conclusion: This is the first quantitative method established to test 1,4-dixoane in a novel scaffold. This method was validated with good accuracy and reproducibility, and met the methodological requirements of the Guideline 9101 documented in the Chinese Pharmacopoeia 2015

JCSC_128_4_633-647_SI.docx

Indian Academy of Sciences (India)

Dell

R2, , PRESS (predicted residual sum of squares) and F values, S3-S4. List of compounds selected as member of test set, S4. Root of squared error and linear correlation For Table 1 in leave-one-out validation method (Figure S1), S5. Root of squared error and linear correlation For Table 1 for doing regression (Figure S2) ...

The [4Fe-4S](2+) cluster in reconstituted biotin synthase binds S-adenosyl-L-methionine.

Science.gov (United States)

Cosper, Michele Mader; Jameson, Guy N L; Davydov, Roman; Eidsness, Marly K; Hoffman, Brian M; Huynh, Boi Hanh; Johnson, Michael K

2002-11-27

The combination of resonance Raman, electron paramagnetic resonance and Mössbauer spectroscopies has been used to investigate the effect of S-adenosyl-l-methionine (SAM) on the spectroscopic properties of the [4Fe-4S]2+ cluster in biotin synthase. The results indicate that SAM interacts directly at a unique iron site of the [4Fe-4S]2+ cluster in BioB and support the hypothesis of a common inner-sphere mechanism for the reductive cleavage of SAM in the radical SAM family of Fe-S enzymes.

Corn Residue Use by Livestock in the United States

Directory of Open Access Journals (Sweden)

Marty R. Schmer

2017-01-01

Full Text Available Corn ( L. residue grazing or harvest provides a simple and economical practice to integrate crops and livestock, but limited information is available on how widespread corn residue utilization is practiced by US producers. In 2010, the USDA Economic Research Service surveyed producers from 19 states on corn grain and residue management practices. Total corn residue grazed or harvested was 4.87 million ha. Approximately 4.06 million ha was grazed by 11.7 million livestock (primarily cattle in 2010. The majority of grazed corn residue occurred in Nebraska (1.91 million ha, Iowa (385,000 ha, South Dakota (361,000 ha, and Kansas (344,000 ha. Average grazing days ranged from 10 to 73 d (mean = 40 d. Corn residue harvests predominantly occurred in the central and northern Corn Belt, with an estimated 2.9 Tg of corn residue harvested across the 19 states. This survey highlights the importance of corn residue for US livestock, particularly in the western Corn Belt.

Mina Shaughnessy in the 1990s: Some Changing Answers in Basic Writing.

Science.gov (United States)

McAlexander, Patricia J.

Although Mina Shaughnessy remains influential in the basic writing field, her answers to the vital questions of who basic writers are and why they underachieve as writers are changing. Whether she intended to or not, Shaughnessy's book "Errors and Expectations" (published in 1977) was a major force in forming an image of basic writers as…

Synthesis of two hyaluronic-acid-related oligosaccharide 4-methoxyphenyl glycosides having a β-D-glucuronic acid residue at the reducing end

NARCIS (Netherlands)

Vliegenthart, J.F.G.; Halkes, K.M.; Slaghek, T.M.; Hyppönen, T.K.; Kamerling, J.P.

1999-01-01

Synthesis of two hyaluronic-acid-related oligosaccharides, the 4-methoxyphenyl beta-glycosides of beta-D-GlcpA-(1->3)-beta-D-GlcpNAc-(1->4)-D-GlcpA and beta-D-GlcpA-(1->3)-beta-D-GlcpNAc-(1->4)-beta-D-GlcpA-(1->3)-beta-D-GlcpNAc-(1->4)-D-GlcpA, is described. D-Glucopyranosyluronic acid residues were

Residue depletion of oxytetracycline (OTC) and 4-epi-oxytetracycline (4-epi-OTC) in broiler chicken's claws by liquid chromatography-tandem mass spectrometry (LC-MS/MS).

Science.gov (United States)

Cornejo, J; Pokrant, E; Araya, D; Briceño, C; Hidalgo, H; Maddaleno, A; Araya-Jordán, C; San Martin, B

2017-04-01

Antibiotics are widely used in poultry production for the treatment of bacterial diseases. However, residues may remain in products and by-products destined for human consumption or animal feeding. The claws of chickens, which are a by-product of the poultry industry, can directly or indirectly enter the food chain as meals destined to feed other productive animals. Thus, it becomes necessary to determine and quantify antimicrobial residues present in this matrix. The objective of the study was to assess the depletion of oxytetracycline (OTC) and its metabolite 4-epi-OTC in broiler chicken's claws. Claws of 32 broilers treated with a therapeutic dosage of 10% OTC during 7 days were analysed. Samples were taken at days 3, 9, 15 and 19 post-treatment. As for the control group, eight broiler chickens were raised under the same conditions. Extraction was carried out through EDTA-McIlvaine buffer, and clean-up employed a SPE C-18 Sep-Pak®. Instrumental analysis was performed through LC-MS/MS. The concentrations of both analytes were determined in claw samples until day 19 post-treatment. Average concentrations were within the LOD (20 μg kg - 1 ) and LOQ (22 µg kg - 1 ) for OTC and 84 μg kg - 1 for 4-epi-OTC. Withdrawal times (WDTs) of 39 days for OTC and 54 days for 4-epi-OTC were established in claws based on 95% confidence. These findings demonstrate that claws can be a source of antimicrobial residue entry into the food chain, since the results showed that OTC and its metabolite can be found in chicken's claws for long periods, even exceeding the average lifespan of a broiler chicken.

The 4p-5d, 6d and 4p-6s, 7s transitions of Mo IX

International Nuclear Information System (INIS)

Khatoon, S.; Chaghtai, M.S.Z.; Rahimullah, K.

1979-01-01

The transitions 4p-5d, 6d and 4p-6s, 7s have been studied for the first time in Mo IX. The authors have identified 42 4p-5d, 36 4p-6d, 22 4p-6s and 22 4p-7s transitions, establishing 16 4p 3 5d, 14 4p 3 6d and all the ten 4p 3 6s, 7s levels of the spectrum concerned. The ionization energy is estimated to be (1 323 700 +- 700)cm -1 or (164.11 +- 0.09)eV. The spectrum was recorded in sliding and open spark discharges with a 5 m grazing incidence spectrograph of Lund University (Sweden) from about 40 A to 440 A. (Auth.)

The dimeric [V2O2F8]4− anion: Structural characterization of a magnetic basic-building-unit

International Nuclear Information System (INIS)

Lu, Hongcheng; Gautier, Romain; Li, Zuo-Xi; Jie, Wanqi; Liu, Zhengtang; Poeppelmeier, Kenneth R.

2013-01-01

New materials built from the [V 2 O 2 F 8 ] 4− anionic basic-building-unit (BBU) exhibit interesting magnetic properties owing to the proximity of the two d 1 V(IV) cations and the orbital interactions of fluoride and oxide ligands. In our search to target such materials, the vanadium oxide–fluoride compound [dpaH 2 ] 2 [V 2 O 2 F 8 ] in which a dimeric anion [V 2 O 2 F 8 ] 4− is isolated in a hydrogen bond network was hydrothermally synthesized (dpa=2,2′-dipyridylamine). This hydrogen bond network is able to stabilize the highly ionic species [V 2 O 2 F 8 ] 4− as demonstrated with bond valence calculations. The coordination of the O 2− /F − ordered ligands was investigated and antiferromagnetic coupling of the isolated BBU was measured. - The new hybrid compound [dpaH 2 ] 2 [V 2 O 2 F 8 ] built from the interesting [V 2 O 2 F 8 ] 4− magnetic basic-building-unit (BBU) was synthesized by the hydrothermal method. The coordination of the O 2− /F − ordered ligands was investigated by BVS calculations and antiferromagnetic coupling was measured. Highlights: ► A new vanadium oxyfluoride was synthesized by hydrothermal method. ► The Dimeric [V 2 O 2 F 8 ] 4− basic building unit is isolated in the hydrogen bond networks. ► The coordination of [V 2 O 2 F 8 ] 4− units to the extended structure is investigated. ► Isolated [V 2 O 2 F 8 ] 4− units exhibit antiferromagnetic coupling

Mechanistic Basis for Type 2 Long QT Syndrome Caused by KCNH2 Mutations that Disrupt Conserved Arginine Residue in the Voltage Sensor

Science.gov (United States)

McBride, Christie M.; Smith, Ashley M.; Smith, Jennifer L.; Reloj, Allison R.; Velasco, Ellyn J.; Powell, Jonathan; Elayi, Claude S.; Bartos, Daniel C.; Burgess, Don E.

2013-01-01

KCNH2 encodes the Kv11.1 channel, which conducts the rapidly activating delayed rectifier K+ current (IKr) in the heart. KCNH2 mutations cause type 2 long QT syndrome (LQT2), which increases the risk for life-threatening ventricular arrhythmias. LQT2 mutations are predicted to prolong the cardiac action potential (AP) by reducing IKr during repolarization. Kv11.1 contains several conserved basic amino acids in the fourth transmembrane segment (S4) of the voltage sensor that are important for normal channel trafficking and gating. This study sought to determine the mechanism(s) by which LQT2 mutations at conserved arginine residues in S4 (R531Q, R531W or R534L) alter Kv11.1 function. Western blot analyses of HEK293 cells transiently expressing R531Q, R531W or R534L suggested that only R534L inhibited Kv11.1 trafficking. Voltage-clamping experiments showed that R531Q or R531W dramatically altered Kv11.1 current (IKv11.1) activation, inactivation, recovery from inactivation and deactivation. Coexpression of wild type (to mimic the patients’ genotypes) mostly corrected the changes in IKv11.1 activation and inactivation, but deactivation kinetics were still faster. Computational simulations using a human ventricular AP model showed that accelerating deactivation rates was sufficient to prolong the AP, but these effects were minimal compared to simply reducing IKr. These are the first data to demonstrate that coexpressing wild type can correct activation and inactivation dysfunction caused by mutations at a critical voltage-sensing residue in Kv11.1. We conclude that some Kv11.1 mutations might accelerate deactivation to cause LQT2 but that the ventricular AP duration is much more sensitive to mutations that decrease IKr. This likely explains why most LQT2 mutations are nonsense or trafficking-deficient. PMID:23546015

Densification of FL Chains via Residuated Frames

Czech Academy of Sciences Publication Activity Database

Baldi, Paolo; Terui, K.

2016-01-01

Roč. 75, č. 2 (2016), s. 169-195 ISSN 0002-5240 R&D Projects: GA ČR GAP202/10/1826 Keywords : densifiability * standard completeness * residuated lattices * residuated frames * fuzzy logic Subject RIV: BA - General Mathematics Impact factor: 0.625, year: 2016

Soluble carbon in oxisol under the effect of organic residue rates

Directory of Open Access Journals (Sweden)

Gabriela Lúcia Pinheiro

2014-06-01

Full Text Available The application of organic residues to the soil can increase soluble organic carbon (SOC and affect the pH and electrolytic conductivity (EC of the soil. However, the magnitude of these changes depends on the type of residue and the applied dose. This study aimed to evaluate the effect of increasing C rates contained in organic residue on the pH, EC, water-extractable total carbon (WETC, water-extractable organic carbon (WEOC, and water-extractable inorganic carbon (WEIC in soil treated with manure (chicken, swine, and quail, sawdust, coffee husk, and sewage sludge. The levels of total C (TC- KH2PO4, organic carbon (OC- KH2PO4, and inorganic C (IC- KH2PO4 extractable by a 0.1 mol L-1 KH2PO4 solution were also quantified in soil under the effect of increasing rates of chicken and quail manures. The following rates of organic residue C were applied to a dystrophic Red Latosol (Oxisol sample: 0, 2,000, 5,000, 10,000, and 20,000 mg kg-1. The addition of organic residues to the soil increased pH, except in the case of sewage sludge, which acidified the soil. The acidity correction potential of chicken and quail manure was highest, dependent on the manure rate applied; regardless of the dose used, sawdust barely alters the soil pH. At all tested rates, the EC of the soil treated with swine manure, coffee husk, and sawdust remained below 2.0 dS m-1, which is a critical level for salinity-sensitive crops. However, the application of chicken or quail manure and sewage sludge at certain rates increased the EC to values above this threshold level. Highest levels of WETC, WEOC, and WEIC were obtained when chicken and quail manure and coffee husk were applied to the Oxisol. The quantities of SOC extracted by KH2PO4 were higher than the quantities extracted by water, demonstrating the ability of soil to adsorb C into its colloids.

Studies of alpha-helicity and intersegmental interactions in voltage-gated Na+ channels: S2D4.

Directory of Open Access Journals (Sweden)

Zhongming Ma

2009-11-01

Full Text Available Much data, including crystallographic, support structural models of sodium and potassium channels consisting of S1-S4 transmembrane segments (the "voltage-sensing domain" clustered around a central pore-forming region (S5-S6 segments and the intervening loop. Voltage gated sodium channels have four non-identical domains which differentiates them from the homotetrameric potassium channels that form the basis for current structural models. Since potassium and sodium channels also exhibit many different functional characteristics and the fourth domain (D4 of sodium channels differs in function from other domains (D1-D3, we have explored its structure in order to determine whether segments in D4 of sodium channels differ significantly from that determined for potassium channels. We have probed the secondary and tertiary structure and the role of the individual amino acid residues of the S2D4 of Na(v1.4 by employing cysteine-scanning mutagenesis (with tryptophan and glutamine substituted for native cysteine. A Fourier transform power spectrum of perturbations in free energy of steady-state inactivation gating (using midpoint potentials and slopes of Boltzmann equation fits of channel availability, h(infinity-V plots indicates a substantial amount of alpha-helical structure in S2D4 (peak at 106 degrees, alpha-Periodicity Index (alpha-PI of 3.10, This conclusion is supported by alpha-PI values of 3.28 and 2.84 for the perturbations in rate constants of entry into (beta and exit from (alpha fast inactivation at 0 mV for mutant channels relative to WT channels assuming a simple two-state model for transition from the open to inactivated state. The results of cysteine substitution at the two most sensitive sites of the S2D4 alpha-helix (N1382 and E1392C support the existence of electrostatic network interactions between S2 and other transmembrane segments within Na(v1.4D4 similar to but not identical to those proposed for K+ channels.

Mobility of organic carbon from incineration residues

International Nuclear Information System (INIS)

Ecke, Holger; Svensson, Malin

2008-01-01

Dissolved organic carbon (DOC) may affect the transport of pollutants from incineration residues when landfilled or used in geotechnical construction. The leaching of dissolved organic carbon (DOC) from municipal solid waste incineration (MSWI) bottom ash and air pollution control residue (APC) from the incineration of waste wood was investigated. Factors affecting the mobility of DOC were studied in a reduced 2 6-1 experimental design. Controlled factors were treatment with ultrasonic radiation, full carbonation (addition of CO 2 until the pH was stable for 2.5 h), liquid-to-solid (L/S) ratio, pH, leaching temperature and time. Full carbonation, pH and the L/S ratio were the main factors controlling the mobility of DOC in the bottom ash. Approximately 60 weight-% of the total organic carbon (TOC) in the bottom ash was available for leaching in aqueous solutions. The L/S ratio and pH mainly controlled the mobilization of DOC from the APC residue. About 93 weight-% of TOC in the APC residue was, however, not mobilized at all, which might be due to a high content of elemental carbon. Using the European standard EN 13 137 for determination of total organic carbon (TOC) in MSWI residues is inappropriate. The results might be biased due to elemental carbon. It is recommended to develop a TOC method distinguishing between organic and elemental carbon

Solvothermal syntheses, crystal structures, and properties of lanthanide(III) thioarsenates [Ln(dien){sub 2}(μ-1κ,2κ{sup 2}-AsS{sub 4})]{sub n} (Ln==Sm, Eu, Gd) and [Ln(dien){sub 2}(1κ{sup 2}-AsS{sub 4})] (Ln==Tb, Dy, Ho)

Energy Technology Data Exchange (ETDEWEB)

Wang, Fang; Tang, Chunying; Chen, Ruihong; Zhang, Yong; Jia, Dingxian, E-mail: jiadingxian@suda.edu.cn

2013-10-15

Solvothermal reactions of Ln{sub 2}O{sub 3}, As and S in diethylenetriamine (dien) at 170 °C for 6 days afforded two structural types of lanthanide thioarsenates with the general formulae [Ln(dien){sub 2}(μ-1κ,2κ{sup 2}-AsS{sub 4})]{sub n} [Ln=Sm(1), Eu(2), Gd(3)] and [Ln(dien){sub 2}(1κ{sup 2}-AsS{sub 4})] [Ln=Tb(4), Dy(5), Ho(6)]. The Ln{sub 2}O{sub 3} oxides were converted to [Ln(dien){sub 2}]{sup 3+} complex units in the solvothermal reactions. The As atom binds four S atoms, forming a tetrahedral AsS{sub 4} unit. In 1−3, the AsS{sub 4} units interconnect the [Ln(dien){sub 2}]{sup 3+} cations via Ln−S bonds as tridentate μ-1κ,2κ{sup 2}-AsS{sub 4} bridging ligands, resulting in the neutral coordination polymers [Ln(dien){sub 2}(μ-1κ,2κ{sup 2}-AsS{sub 4})]{sub n} (Ln1). In 4−6, the AsS{sub 4} units coordinate with the Ln{sup 3+} ion of [Ln(dien){sub 2}]{sup 3+} as 1κ{sup 2}-AsS{sub 4} chelating ligands to form neutral coordination compounds [Ln(dien){sub 2}(1κ{sup 2}-AsS{sub 4})] (Ln2). The Ln{sup 3+} ions are in nine- and eight-coordinated environments in Ln1 and Ln2, respectively. The formation of Ln1 and Ln2 is related with ionic size of the Ln{sup 3+} ions. Optical absorption spectra showed that 1−6 have potential use as semiconductors with the band gaps in the range 2.18−3.21 eV. - Graphical abstract: Two types of Ln-thioarsenates [Ln(dien){sub 2}(μ-1κ,2κ{sup 2}-AsS{sub 4})]{sub n} and [Ln(dien){sub 2}(1κ{sup 2}-AsS{sub 4})] were prepared by solvothermal methods and the soft Lewis basic AsS{sub 4}{sup 3–} ligand to Ln(III) centers with polyamine co-ligand was obtained. Display Omitted - Highlights: • Lanthanide thioarsenates were prepared by solvothermal methods. • The soft Lewis basic AsS{sub 4} ligand coordinate Ln{sup 3+} ions with coexistence polyamine ligands. • Two structural types of Ln-thioarsenates with structural turnover at Tb were obtained along Ln series. • The Ln-thioarsenates are potential semiconductors

Characterization of ferric arsenate-sulfate compounds: Implications for arsenic control in refractory gold processing residues

Czech Academy of Sciences Publication Activity Database

Paktunc, D.; Majzlan, J.; Palatinus, Lukáš; Dutrizac, J.; Klementová, Mariana; Poirier, G.

2013-01-01

Roč. 98, č. 4 (2013), s. 554-565 ISSN 0003-004X Institutional support: RVO:68378271 Keywords : arsenic * ferric arsenate sulfate * autoclave residue * hydrometallurgy Subject RIV: DB - Geology ; Mineralogy Impact factor: 2.059, year: 2013

Turbidez e cloro residual livre na monitoração de ETE tipo tanque séptico seguido de filtro anaeróbio - doi: 10.4025/actascitechnol.v33i4.9603 Turbidity and free residual chlorine for monitoring plants comprised by septic tank followed by anaerobic filter

Directory of Open Access Journals (Sweden)

Raimundo Oliveira de Souza

2011-09-01

Full Text Available A avaliação dos dados agrupados da monitoração de 16 ETEs do tipo tanque séptico (TSEP seguido por filtro anaeróbio (FAN mostrou remoção média global de 55% para DQO e SST. O desempenho alcançado foi abaixo do sugerido pela literatura, porém compatível com o de estudos recentes sobre sistemas em escala real no país. A remoção média global de bactérias do grupo coliforme, após desinfecção com solução de hipoclorito de sódio, foi de 3,0 unidades de log. Remoção mais elevada ocorreu com Escherichia coli como indicador (3,5 logs. Em geral, as maiores remoções de coliformes foram alcançadas com concentrações de cloro residual livre (CRL variando de 2,0 a 2,5 mg L-1. Os resultados mostraram a aplicabilidade da turbidez para estimar concentrações de SST e DQO no efluente tratado. Observou-se também que a concentração de CRL é útil para estimar as concentrações de bactérias do grupo coliforme.Grouped monitoring data of 16 wastewater treatment plants was investigated. The plants were comprised by septic tanks followed by anaerobic filters and effluent disinfection with sodium hypochlorite. Removal of COD and total suspended solids was about 55%. This number was below values observed by the literature. However, the results were in accordance with recent findings in Brazilian full-scale plants. Coliform removal was about 3.0 log units with better results for Escherichia coli (3.5 logs. Best results were achieved with free residual chorine concentrations ranging from 2.0 to 2.5 mg L-1. Findings showed that turbidity is a useful parameter to estimate COD and TSS concentrations in the treated effluent. Free residual chlorine may also be applied to estimate coliform numbers.

Preparation, properties and anticancer effects of mixed As4S4/ZnS nanoparticles capped by Poloxamer 407

International Nuclear Information System (INIS)

Bujňáková, Z.; Baláž, M.; Zdurienčíková, M.; Sedlák, J.; Čaplovičová, M.; Čaplovič, Ľ.; Dutková, E.; Zorkovská, A.; Turianicová, E.; Baláž, P.; Shpotyuk, O.

2017-01-01

Arsenic sulfide compounds have a long history of application in a traditional medicine. In recent years, realgar has been studied as a promising drug in cancer treatment. In this study, the arsenic sulfide (As 4 S 4 ) nanoparticles combined with zinc sulfide (ZnS) ones in different molar ratio have been prepared by a simple mechanochemical route in a planetary mill. The successful synthesis and structural properties were confirmed and followed via X-ray diffraction and high-resolution transmission electron microscopy measurements. The morphology of the particles was studied via scanning electron microscopy and transmission electron microscopy methods and the presence of nanocrystallites was verified. For biological tests, the prepared As 4 S 4 /ZnS nanoparticles were further milled in a circulation mill in a water solution of Poloxamer 407 (0.5 wt%), in order to cover the particles with this biocompatible copolymer and to obtain stable nanosuspensions with unimodal distribution. The average size of the particles in the nanosuspensions (~ 120 nm) was determined by photon cross-correlation spectroscopy method. Stability of the nanosuspensions was determined via particle size distribution and zeta potential measurements, confirming no physico-chemical changes for several months. Interestingly, with the increasing amount of ZnS in the sample, the stability was improved. The anti-cancer effects were tested on two melanoma cell lines, A375 and Bowes, with promising results, confirming increased efficiency of the samples containing both As 4 S 4 and ZnS nanocrystals. - Highlights: • Mixed As 4 S 4 /ZnS nanoparticles were prepared by dry milling in the first stage • Stable nanosuspensions of As 4 S 4 /ZnS nanoparticles capped by Poloxamer 407 were prepared by wet milling in the second stage • ZnS in the samples is beneficial: higher values of S A , stability, solubility and anticancer activity were improved

Residues of 2, 4-D in air samples from Saskatchewan: 1966-1975.

Science.gov (United States)

Grover, R; Kerr, L A; Wallace, K; Yoshida, K; Maybank, J

1976-01-01

Residues of 2,4-D (2,4-dichlorophenoxyacetic acid) in air samples from several sampling sites in central and southern Saskatchewan during the spraying seasons in the 1966-68 and 1970-75 periods were determined by gas-liquid chromatographic techniques. Initially, individual esters of 2,4-D were characterized by retention times and confirmed further by co-injection and dual column procedures. Since 1973, however, only total 2,4-D acid levels in air samples have been determined after esterification to the methyl ester and confirmed by gc/ms techniques whenever possible. Up to 50% of the daily samples collected during the spraying season at any of the locations and during any given year contained 2,4-D, with butyl esters being found most frequently. The daily 24-hr mean atmospheric concentrations of 2,4-D ranged from 0.01 to 1.22 mug/m3, 0.01 to 13.50 mug/m3, and 0.05 to 0.59 mug/m3 for the iso-propyl, mixed butyl and iso-octyl esters, respectively. Even when the samples were analysed for the total 2,4-D content, i.e. from 1973 onwards, the maximum level of the total acid reached only 23.14 mug/m3. In any given year and at any of the sampling sites, about 30% of the samples contained less than 0.01 mug/m3 of 2,4-D. In another 40% of the samples, the levels of 2,4-D ranged from 0.01 to 0.099 mug/m3. Only about 30% of the samples contained 2,4-D concentrations higher than 0.1 mug/m3, with only 10% or less exceeding 1 mug/m3. None of the samples, obtained with the high volume particulate sampler, showed any detectable levels of 2,4-D, indicating little or no transport of 2,4-D adsorbed on dust particles or as crystals of amine salts.

Uso del residual sólido de biogás para la producción de hortalizas en huertos intensivos./Use of biogas solid waste for intensive vegetable production gardens

Directory of Open Access Journals (Sweden)

Pável Chaveli Chávez

2014-01-01

Full Text Available Resumen:Se llevó a cabo un estudio para medir el comportamiento de la utilización de diferentes dosis de residual sólido de producción de biogás (0.5; 1.0; 1.5 y 2.0 kg.m-2 en tres momentos de aplicación (al inicio, cada dos cultivos y en cada cultivo en una secuencia de hortalizas. Se empleó un diseño de bloques al azar con tres repeticiones. Se realizaron muestreos al suelo al término del ciclo de cultivo y se determinó pH (KCl, contenido de fósforo, potasio y el porciento de materia orgánica. Del análisis de los resultados se obtuvo que la dosis de 1 kg.m-2 del residual de biogás en su estado sólido aplicado cada dos cultivos logro incrementos de los rendimientos por encima del 30% con respecto a la no aplicación del residual. Los contenidos de P2O5 y K2O y el % de materia orgánica se favorecieron con el uso del abono al término del ciclo de las hortalizas, lo que permite la explotación intensiva del suelo./Abstract: A study was conducted to measure the performance of using different doses of solid waste in biogas production (0.5, 1.0, 1.5 and 2.0 kg.m-2 in three application times (at baseline, each two crops and in each crop in a sequence of vegetables. Design of randomized blocks with three replications was employed. Soil sampling at the end of the crop cycle were performed and pH (KCl, content of phosphorus, potassium and the percentage of organic matter was determined. Analysis of the results obtained that the dose of 1 kg.m-2 residual biogas in its solid state achievement applied every two crops yield increases above 30% over the non-implementation of the residual. The P2O5 and K2O and % organic matter contents were favored by the use of the organic fertilizer at the end of the cycle of the vegetables, allowing the intensive soil use.

Food toxicology. Residues and contaminants: Risks and consumer protection; Lebensmitteltoxikologie. Rueckstaende und Kontaminanten: Risiken und Verbraucherschutz

Energy Technology Data Exchange (ETDEWEB)

Nau, H. [Tieraerztliche Hochschule Hannover, ZA Lebensmitteltoxikologie (Germany); Steinberg, P. [Potsdam Univ., Inst. fuer Ernaehrungswissenschaft (Germany); Kietzmann, M. (eds.) [Tieraerztliche Hochschule Hannover, Inst. fuer Pharmakologie, Toxikologie/Pharmazie (Germany)

2003-07-01

In a detailed introduction, the basic methods of risk assessment for potentially toxic food constituents are presented as well as the analytical methods applied for measuring even very small concentrations of contaminants. The main classes of substances relevant in foods ar represented, i.e. animal drugs, fungicides and herbicides, natural toxins, contaminants, prions from BSE-infested animals and residues of 'new' proteins and 'new' DNA from genetically modified foods. New legislation in Germany and Europe is presented including the National Residue Monitoring Plant which is to enable annual monitoring of residue concentrations in foods derived from animals. (orig.)

Agrochemical residues in rivers sediments, Poas, Costa Rica

International Nuclear Information System (INIS)

Masis, Federico; Valdez, Juan; Leon, Sandra; Coto, Tatiana

2008-01-01

The organophosphorus and organochlorine agrochemical residues distribution in sediments of 3 rivers located in an ornamental plant production area were analyzed in Poas canton, Alajuela, Costa Rica. The study comprised 8 months in order to assure 3 seasonal episodes: dry, transitional, and rainy seasons. Sediments were taken in 10 sampling stations along the rivers and characterized by a determination of their organic matter and texture. In 7 out of 10 sampling stations pesticide residues were detected in at least 1 of 4 samplings, but quantified only in 4 stations. Agrochemical residues evaluated included 21 organophosphorus and organochlorine pesticides; however, we found residues of only 3 organochlorine pesticides, due their high persistence in the sediment. Residues corresponded to PCNB (80-800 μg.kg -1 ), Endosulfan-β (40-50 μg.kg -1 ), and Endosulfan-α (90 μg.kg -1 ). Chlorothalonil was detected in only one sample. (author) [es

X-ray measurement of residual stress in metals at Chalk River Nuclear Laboratories

International Nuclear Information System (INIS)

Winegar, J.E.

1980-06-01

X-ray diffraction is used at CRNL to measure residual stress in metals. This report summarizes the basic principles of stress measurement, and reviews factors affecting accuracy of measurement. The technique and equipment described were developed at CRNL to give reliable measurements. Accuracy of measurement is achieved by using fixed-count step-scanning and by computer analysis of intensity data using a cubic spline curve smoothing routine. Specific reference is made to the measurement of residual stress in Inconel-600 and Incoloy-800 boiler tubing. Because it measures stress in thin surface layers, the X-ray method can also be used to measure the depth profile of stresses. As there are no standardized procedures for measuring residual stress, this report will be useful both to those unfamiliar with the measurement of residual stress and to those already making such measurements in other laboratories. (auth)

Problems and Guidelines of Strategy Implementation in Basic Educational Institutions under the Supervision of KhonKaen Primary Educational Service Area Office 4

Directory of Open Access Journals (Sweden)

Sasiwan Tonkanya

2016-09-01

Full Text Available The research aimed to 1 study problems of strategy implementation in basic educational institutions under Khonkaen Primary Educational Service Area Office 4 ; and 2 propose the guidelines for strategy implementation in basic educational institutions under Khonkaen Primary Educational Service Area Office 4. The study was carried out in 2 phases. In phase 1, it focused on the study and analysis of the strategic implementation problems and phase 2 studied the best practice schools. The informants for the interview in phase 1 comprised 6 school administrators and teachers who were involved in strategy implementation from small-sized, medium-sized, and large-sized schools. They were selected by the use of purposive sampling technique. The population in the study of the strategic implementation problems in basic educational institutions in phase 1 consisted of 543 school administrators and teachers who were involved in strategy implementation from 181 schools under Khonkaen Primary Educational Service Area Office 4 in academic year 2014. The study samples were 217 school administrators and teachers who were involved in strategy implementation from small-sized, medium-sized, and large-sized schools under Khonkaen Primary Educational Service Area Office 4. The samples were selected by the use of stratified sampling technique. The informants of the phase 2 study were 6 school administrators and teachers who were involved in strategy implementation from small-sized, medium-sized, and large-sized best practice schools obtained from purposive sampling technique. The research instruments used for data collection consisted of 2 sets of questionnaires. The Set 1 questionnaire was the 5-point Likert scale on the levels of the problems in implementation with item discrimination at 0.60 – 1.00 and reliability of the whole questionnaire at .9359. The questionnaire contained 3 parts with 65 items. The Set 2 questionnaire comprised 2 parts with 10 items regarding

Carbonaceous materials in the acid residue from the Orgueil carbonaceous chondrite meteorite

Science.gov (United States)

Garvie, Laurence A. J.; Buseck, Peter R.

2006-04-01

Insoluble organic matter (IOM) dominates the HF/HCl residue of the Orgueil (CI) carbonaceous chondrite meteorite. The IOM is composed primarily of two C-rich particle types. The first has a fluffy texture similar to crumpled tissue paper, and the second type occurs as solid or hollow nanospheres. High-resolution transmission electron microscope (HRTEM) images of the fluffy material show it is poorly ordered, with small, irregularly shaped regions having fringes with 0.34-0.38 nm spacings and locally 0.21 nm cross-fringes. Nanodiamonds occur in the fluffy material. The rounded C-rich particles are common in the residue and their HRTEM images show neither fringes nor nanodiamonds. Both types of carbonaceous materials have a high aromatic component, as revealed by electron energy-loss spectroscopy (EELS), with up to 10 at% substitution by S, N, and O. The average compositions of the fluffy material and nanospheres are C100S1.9N3.7O4.9 and C100S2.4N5.0O3.9, respectively. The structural and chemical heterogeneity of the carbonaceous materials may represent material from multiple sources.

Bacillus subtilis with endocellulase and exocellulase activities isolated in the thermophilic phase from composting with coffee residues.

Science.gov (United States)

Siu-Rodas, Yadira; Calixto-Romo, María de Los Angeles; Guillén-Navarro, Karina; Sánchez, José E; Zamora-Briseño, Jesús Alejandro; Amaya-Delgado, Lorena

2017-12-27

The goal of this study was to isolate, select and characterize bacteria with cellulolytic activity from two different coffee residue composting piles, one of which had an internal temperature of 57°C and pH 5.5 and the other, a temperature of 61°C, and pH 9.3. Culture media were manipulated with carboxymethylcellulose and crystalline cellulose as sole carbon sources. The enzyme activity was assessed by hydrolysis halo formation, reducing sugar production and zymograms. Three out of twenty isolated strains showed higher enzymatic activity and were identified as Bacillus subtilis according to their morphological, physiological, biochemical characteristics and based on the sequence analysis of 16S rDNA regions. The enzymatic extracts of the three selected strains showed exocellulase and endocellulase maximum activity of 0.254 and 0.519 U/ml, respectively; the activity of these enzymes was maintained even in acid pH (4.8) and basic (9.3) and at temperatures of up to 60°C. The enzymatic activities observed in this study are within the highest reported for cellulose produced by bacteria of the genus Bacillus. Endocellulase activity was shown in the zymograms from 24h until 144h of incubation. Furthermore, the pH effect on the endocellulase activity is reported for the first time by zymograms. The findings in this study entail the possibility to use these enzymes in the procurement of fermentable substrates for the production of energy from the large amount of residues generated by the coffee agroindustry. Copyright © 2017 Asociación Argentina de Microbiología. Publicado por Elsevier España, S.L.U. All rights reserved.

Improved GaSb surfaces using a (NH4)2S/(NH4)2S04 solution

International Nuclear Information System (INIS)

Murape, D.M.; Eassa, N.; Nyamhere, C.; Neethling, J.H.; Betz, R.; Coetsee, E.; Swart, H.C.; Botha, J.R.; Venter, A.

2012-01-01

Bulk (1 0 0) n-GaSb surfaces have been treated with a sulphur based solution ((NH 4 ) 2 S/(NH 4 ) 2 SO 4 ) to which sulphur has been added, not previously reported for the passivation of GaSb surfaces. Au/n-GaSb Schottky barrier diodes (SBDs) fabricated on the treated material show significant improvement compared to that of the similar SBDs on the as-received material as evidenced by the lower ideality factor (n), higher barrier height (φ b ) and lower contact resistance obtained. Additionally, the reverse leakage current, although not saturating, has been reduced by almost an order of magnitude at −0.2 V. The sample surfaces were studied by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The native oxide, Sb–O, present on the as-received material is effectively removed on treating with ([(NH 4 ) 2 S/(NH 4 ) 2 SO 4 ]+S) and (NH 4 ) 2 S. Analysis of the as-received surface by XPS, prior to and after argon sputtering, suggests that the native oxide layer is ≤8.5 nm.

Synthesis and structure of Li{sub 4}GeS{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Matsushita, Y [National Inst. of Materials and Chemical Research, Tsukuba (Japan). High Pressure Lab.; Kanatzidis, M G [Michigan State Univ., East Lansing, MI (United States). Dept. of Chemistry

1998-01-01

The compound Li{sub 4}GeS{sub 4} has been prepared as transparent, light yellow moisture-sensitive crystals. Li{sub 4}GeS{sub 4} belongs to the space group Pnma with a = 14.107(6) A, b = 7.770(3) A and c = 6.162(2) A. The crystal structure was solved by direct-methods. The final R and R{sub w}-values are 1.85 and 1.65% for 866 observed reflections. The Li{sub 4}GeS{sub 4} structure has three crystallographically independent lithium sites and one germanium site. The lithium atoms adopt two different coordination types. The Li1 atom is coordinated to five sulfur atoms in a square pyramidal geometry, while the Li2 and Li3 atoms have distorted tetrahedral coordination. The Ge atom is tetrahedrally coordinated by four sulfur atoms and is found as [GeS{sub 4}]{sup 4-} units. The anisotropic three-dimensional crystal structure of Li{sub 4}GeS{sub 4} is described. (orig.) 57 refs.

Treatment of waste incinerator air-pollution-control residues with FeSO4: Concept and product characterization

DEFF Research Database (Denmark)

Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

2002-01-01

This paper describes a new concept for treatment of air- pollution-control (APC) residues from waste incineration and characterises the wastewater and stabilised residues generated by the process. The process involves mixing of APC-residues with a ferrous sulphate solution and subsequent oxidation...

Role of long- and short-range hydrophobic, hydrophilic and charged residues contact network in protein’s structural organization

Directory of Open Access Journals (Sweden)

Sengupta Dhriti

2012-06-01

Full Text Available Abstract Background The three-dimensional structure of a protein can be described as a graph where nodes represent residues and the strength of non-covalent interactions between them are edges. These protein contact networks can be separated into long and short-range interactions networks depending on the positions of amino acids in primary structure. Long-range interactions play a distinct role in determining the tertiary structure of a protein while short-range interactions could largely contribute to the secondary structure formations. In addition, physico chemical properties and the linear arrangement of amino acids of the primary structure of a protein determines its three dimensional structure. Here, we present an extensive analysis of protein contact subnetworks based on the London van der Waals interactions of amino acids at different length scales. We further subdivided those networks in hydrophobic, hydrophilic and charged residues networks and have tried to correlate their influence in the overall topology and organization of a protein. Results The largest connected component (LCC of long (LRN-, short (SRN- and all-range (ARN networks within proteins exhibit a transition behaviour when plotted against different interaction strengths of edges among amino acid nodes. While short-range networks having chain like structures exhibit highly cooperative transition; long- and all-range networks, which are more similar to each other, have non-chain like structures and show less cooperativity. Further, the hydrophobic residues subnetworks in long- and all-range networks have similar transition behaviours with all residues all-range networks, but the hydrophilic and charged residues networks don’t. While the nature of transitions of LCC’s sizes is same in SRNs for thermophiles and mesophiles, there exists a clear difference in LRNs. The presence of larger size of interconnected long-range interactions in thermophiles than mesophiles, even at

Low-residue euthanasia of stranded mysticetes.

Science.gov (United States)

Harms, Craig A; McLellan, William A; Moore, Michael J; Barco, Susan G; Clarke, Elsburgh O; Thayer, Victoria G; Rowles, Teresa K

2014-01-01

Euthanasia of stranded large whales poses logistic, safety, pharmaceutical, delivery, public relations, and disposal challenges. Reasonable arguments may be made for allowing a stranded whale to expire naturally. However, slow cardiovascular collapse from gravitational effects outside of neutral buoyancy, often combined with severely debilitating conditions, motivate humane efforts to end the animal's suffering. The size of the animal and prevailing environmental conditions often pose safety concerns for stranding personnel, which take priority over other considerations. When considering chemical euthanasia, the size of the animal also necessitates large quantities of euthanasia agents. Drug residues are a concern for relay toxicity to scavengers, particularly for pentobarbital-containing euthanasia solutions. Pentobarbital is also an environmental concern because of its stability and long persistence in aquatic environments. We describe a euthanasia technique for stranded mysticetes using readily available, relatively inexpensive, preanesthetic and anesthetic drugs (midazolam, acepromazine, xylazine) followed by saturated KCl delivered via custom-made needles and a low-cost, basic, pressurized canister. This method provides effective euthanasia while moderating personnel exposure to hazardous situations and minimizing drug residues of concern for relay toxicity.

Synthesis and physico-chemical properties of (R,S)-6-ditrideuteriomethylamino-4,4-diphenylheptan-3-one hydrochloride (methadone-d6)

International Nuclear Information System (INIS)

Gerardy, B.M.; Poupaert, J.H.; Vandervorst, D.; Dumont, P.; Declerq, J.-P.; Meerssche, M. van; Portoghese, P.S.

1985-01-01

A reaction sequence is described to synthesize (R,S)-6-ditrideuteriomethylamino-4,4-diphenylheptan-3-one hydrochloride (methado-ne-d 6 .HC1) in 10.5% overall yield starting from dimethylamine-d 6 hydrochloride. While methadone-d 6 .HC1 had rather similar physicochemical properties compared to methadone.HC1 in the solid phase, a divergent behaviour was observed in solution (pKa, chromatographic and 13 C-NMR data). A higher basicity along with a more important hydrophilicity were observed for the d 6 -derivative. A 13 C-NMR study showed significant differences in the 13 C chemical shifts, which were attributed in part to the intrinsic nature of D itself and in part to a conformational perturbation. The longer duration of antinociceptive action, along with higher tsub(1/2) and clearance, and the depression of the metabolic N-demethylation process were the only biological properties modified by the deuteration. (author)

38 CFR 21.142 - Adult basic education.

Science.gov (United States)

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Adult basic education. 21...) VOCATIONAL REHABILITATION AND EDUCATION Vocational Rehabilitation and Employment Under 38 U.S.C. Chapter 31 Special Rehabilitation Services § 21.142 Adult basic education. (a) Definition. The term adult basic...

[Preparation and evaluation of stationary phase of high performance liquid chromatography for the separation of basic solutes].

Science.gov (United States)

Wang, P; Wang, J; Cong, R; Dong, B

1997-05-01

A bonded phase for high performance liquid chromatography (HPLC) has been prepared by the new reaction between silica and silicon ether. The ether was synthesized from alkylchlorosilane and pentane-2,4-dione in the presence of imidazole under inert conditions by using anhydrous tetrahydrofuran as solvent. The bonded phase thus obtained was characterized by elemental analysis, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy and HPLC evaluation. The carbon content was 9.4% and the surface coverage almost attained 3.0micromol/m2 without end-capping. The silanol absorption peaks of the product cannot be observed from the DRIFT spectrum, which revealed that the silanization reaction proceeded thoroughly. The basic solutes, such as aniline, o-toluidine, p-toluidine, N,N-dimethylaniline and pyridine were used as the probe solutes to examine their interaction with the residual silanols on the surface of the products. No buffer or salt was used in the mobile phase for these experiments. In comparison with an acidic solute, such as, phenol, basic aniline eluted in front of phenol, and the ratio of asymmetry of aniline peak to that of the phenol peak was 1.1. Furthermore the relative k' value of p-toluidine to that of o-toluidine was also 1.1. All the results showed that the stationary phase has better quality and reproducibility and can be used for the separation of basic solutes efficiently.

An Assessment of Subsurface Residual Stress Analysis in SLM Ti-6Al-4V

Directory of Open Access Journals (Sweden)

Tatiana Mishurova

2017-03-01

Full Text Available Ti-6Al-4V bridges were additively fabricated by selective laser melting (SLM under different scanning speed conditions, to compare the effect of process energy density on the residual stress state. Subsurface lattice strain characterization was conducted by means of synchrotron diffraction in energy dispersive mode. High tensile strain gradients were found at the frontal surface for samples in an as-built condition. The geometry of the samples promotes increasing strains towards the pillar of the bridges. We observed that the higher the laser energy density during fabrication, the lower the lattice strains. A relief of lattice strains takes place after heat treatment.

Study of a nickel-copper filter for the future conditioning of insoluble residues

Energy Technology Data Exchange (ETDEWEB)

Massoni, Nicolas, E-mail: nicolas.massoni@cea.fr

2016-10-15

This paper deals with the feasibility of a separate conditioning for insoluble residues coming from spent nuclear fuel reprocessing. The two possible conditioning routes considered for insoluble residues were (i) added with cladding hulls with the considered filter (route #1) or (ii) melted with a nickel copper alloy already studied (route #2). Only route #2 was dealt with in this study. In France, the current practice is to store insoluble residues in a water suspension. For the two conditioning routes described here, dry insoluble residues are required for safety with melted metals. A nickel-copper filter was developed that can serve for the two types of conditioning. A filtration test performed with molybdenum particles as insoluble residue surrogates was done. The particle-charged filter was sintered, and Mo particles were kept inside the filter. Thus an integrated flowsheet for the filtration and immobilization of insoluble residues was demonstrated. - Highlights: • The basics for an integrated flowsheet for the filtration and immobilization of insoluble residues were demonstrated. • The filter can serve as an immobilization matrix or can be added in another metal waste. • A theoretical calculation has shown that the conception of the filter should be done to avoid an excessive heat-up.

Peer review, basic research, and engineering: Defining a role for QA professionals in basic research environments

Energy Technology Data Exchange (ETDEWEB)

Bodnarczuk, M.

1989-02-01

Within the context of doing basic research, this paper seeks to answer four major questions: (1) What is the authority structure of science. (2) What is peer review. (3) Where is the interface between basic physics research and standard engineering. and (4) Given the conclusions to the first three questions, what is the role of the QA professional in a basic research environment like Fermilab. 23 refs.

Children and Their Basic Needs.

Science.gov (United States)

Prince, Debra Lindsey; Howard, Esther M.

2002-01-01

Describes obstacles presented by poverty in the fulfillment of the basic needs of children. Individually addresses Maslow's five basic needs with regard to children reared in poverty: (1) physiological needs; (2) safety needs; (3) belonging and love needs; (4) self-esteem needs; and (5) self-actualization needs. (Author/SD)

Synthesis of two hyaluronic-acid-related oligosaccharide 4-methoxyphenyl glycosides having a beta-D-glucuronic acid residue at the reducing end

NARCIS (Netherlands)

Halkes, K.M.; Slaghek, T.M.; Hypponen, T.K.; Kamerling, J.P.; Vliegenthart, J.F.G.

1999-01-01

Synthesis of two hyaluronic-acid-related oligosaccharides, the 4-methoxyphenyl β-glycosides of β-D-GlcpA-(1→3)-β-D-GlcpNAc-(1→4)-D-GlcpA and β-D-GlcpA-(1→3)-β-D-GlcpNAc-(1→4)-β-D-GlcpA-(1→3)- β-D-GJcpNAc-(1→4)-D-GlcpA, is described. D-Glucopyranosyluronic acid residues were obtained by selective

Comparing Dislodgeable 2,4-D Residues across Athletic Field Turfgrass Species and Time.

Directory of Open Access Journals (Sweden)

Matthew D Jeffries

Full Text Available 2,4-dimethylamine salt (2,4-D is an herbicide commonly applied on athletic fields for broadleaf weed control that can dislodge from treated turfgrass. Dislodge potential is affected by numerous factors, including turfgrass canopy conditions. Building on previous research confirming herbicide-turfgrass dynamics can vary widely between species, field research was initiated in 2014 and 2015 in Raleigh, NC, USA to quantify dislodgeable 2,4-D residues from dormant hybrid bermudagrass (Cynodon dactylon L. x C. transvaalensis and hybrid bermudagrass overseeded with perennial ryegrass (Lolium perenne L., which are common athletic field playing surfaces in subtropical climates. Additionally, dislodgeable 2,4-D was compared at AM (7:00 eastern standard time and PM (14:00 sample timings within a day. Samples collected from perennial ryegrass consistently resulted in greater 2,4-D dislodgment immediately after application (9.4 to 9.9% of applied compared to dormant hybrid bermudagrass (2.3 to 2.9%, as well as at all AM compared to PM timings from 1 to 3 d after treatment (DAT; 0.4 to 6.3% compared to 0.1 to 0.8%. Dislodgeable 2,4-D did not differ across turfgrass species at PM sample collections, with ≤ 0.1% of the 2,4-D applied dislodged from 1 to 6 DAT, and 2,4-D detection did not occur at 12 and 24 DAT. In conclusion, dislodgeable 2,4-D from treated turfgrass can vary between species and over short time-scales within a day. This information should be taken into account in human exposure risk assessments, as well as by turfgrass managers and athletic field event coordinators to minimize 2,4-D exposure.

Fine definition of the CXCR4-binding region on the V3 loop of feline immunodeficiency virus surface glycoprotein.

Directory of Open Access Journals (Sweden)

Qiong-Ying Hu

2010-05-01

Full Text Available The chemokine receptor CXCR4 is shared by primary and laboratory-adapted strains of feline immunodeficiency virus (FIV for viral entry. Our previous studies implicated a contiguous nine-amino-acid region of the V3 loop of the FIV envelope surface as important in CXCR4 binding and virus entry. The binding is specific for CXCR4 since it can be inhibited by AMD3100, a selective CXCR4 inhibitor. Additional site-directed mutagenesis was used to further reveal the key residues. Binding studies indicated that basic residues R395, K397, R399 as well as N398 are critical for CXCR4 binding. The effect of other amino acid residues on receptor binding depends on the type of amino acid residue substituted. The binding study results were confirmed on human CXCR4-expressing SupT1 cells and correlated with entry efficiency using a virus entry assay. Amino acid residues critical for CXCR4 are not critical for interactions with the primary binding receptor CD134, which has an equivalent role as CD4 for HIV-1 binding. The ELISA results show that W394 and W400 are crucial for the recognition by neutralizing anti-V3 antibodies. Since certain strains of HIV-1 also use CXCR4 as the entry receptor, the findings make the feline model attractive for development of broad-based entry antagonists and for study of the molecular mechanism of receptor/virus interactions.

PENETAPAN RESIDU DAN PERKIRAAN PENETAPAN BATAS MAKSIMUM RESIDU (BMR ORGANOKLORIN PADA SIMPLISIA

Directory of Open Access Journals (Sweden)

Ani Isnawati

2012-10-01

Full Text Available Penggunaaan bahan obat tradisional (simplisia untuk skala industri dan peningkatan produksi tanaman obat dalam skala besar menjadi tidak ekonomis tanpa pestisida. Disatu sisi penggunaan pestisida dapat menguntungkan yaitu menyebabkan toksis pada hama namun disisi lain toksisitas dapat terjadi juga pada manusia, sehingga residu pestisida dalam tanaman obat yang dikonsumsi dalam jangka panjang akan merugikan kesehatan. Batas maksimum Residu (BMR pestisida dalam simplisia baik di Indonesia maupun di negara lain belum ditetapkan. Sehingga untuk itu untuk mengetahui adanya residu pestisida jenis organoklorin yang telah dilarang penggunaannya melalui Permentan No.434.1/kpts/TP.270/7/2001 dan untuk mengetahui batas keamanannya, maka perlu dilakukan penetapan residu organoklorin dalam simplisia dan menetapkan batas keamanan berdasarkan perhitungan secara teoritis. Pengujian residu dilakukan terhadap golongan pestisida organoklorin pada 4 jenis simplisia (daun wungu (Graptophyllum pictum (L Grifl, daun sambiloto Andrographis paniculata Ness, herba pegagan (Centella  asiatica (L Urban, daun tempuyung (Sonchus arvensis (L yang berasal dari 3 lokasi penanaman, yaitu : perkebunan Tanaman Obat Manako (Jawa Barat, Balai Penelitian Tanaman Obat Tawangmangu (BPTO di Jawa Tengah dan Perkebunan Tanaman Obat Purwodadi (Jawa Timur. Pemeriksaan residu pestisida organoklorin menggunakan kromatografi gas dan perhitungan batas keamanan dihitung dengan adanya nilai ADI (Acceptable daily intake yang telah ditetapkan bersama antara JAO dan WHO serta perkiraan banyaknya konsumsi simplisia. Hasil Pengujian residu pestisida organoklorin diperoleh bahwa simplisia daun Wungu (Tawangmangu mengandung residu lindan dengan kadar 0,24 mg/kg, pegagan (Purwodadi, mengandung lindan 0,36 mg/kg dan aldrin 0,31 mg/kg serta pegagan (Manako mengandung heptaklor 0,15 mg/kg dan op-DDE 0,11 mg/kg. Adapun penghitungan BMR heptaklor dan lindan secara teoritis dengan asumsi rata

Syntheses, structural variants and characterization of AInM′S4 (A=alkali metals, Tl; M′ = Ge, Sn) compounds; facile ion-exchange reactions of layered NaInSnS4 and KInSnS4 compounds

International Nuclear Information System (INIS)

Yohannan, Jinu P.; Vidyasagar, Kanamaluru

2016-01-01

Ten AInM′S 4 (A=alkali metals, Tl; M′= Ge, Sn) compounds with diverse structure types have been synthesized and characterized by single crystal and powder X-ray diffraction and a variety of spectroscopic methods. They are wide band gap semiconductors. KInGeS 4 (1-β), RbInGeS 4 (2), CsInGeS 4 (3-β), TlInGeS 4 (4-β), RbInSnS 4 (8-β) and CsInSnS 4 (9) compounds with three-dimensional BaGa 2 S 4 structure and CsInGeS 4 (3-α) and TlInGeS 4 (4-α) compounds with a layered TlInSiS 4 structure have tetrahedral [InM′S 4 ] − frameworks. On the other hand, LiInSnS 4 (5) with spinel structure and NaInSnS 4 (6), KInSnS 4 (7), RbInSnS 4 (8-α) and TlInSnS 4 (10) compounds with layered structure have octahedral [InM′S 4 ] − frameworks. NaInSnS 4 (6) and KInSnS 4 (7) compounds undergo facile topotactic ion-exchange, at room temperature, with various mono-, di- and tri-valent cations in aqueous medium to give rise to metastable layered phases. - Graphical abstract: NaInSnS 4 and KInSnS 4 compounds undergo, in aqueous medium at room temperature, facile topotactic ion-exchange with mono, di and trivalent cations. Display Omitted - Highlights: • Ten AInM′S 4 compounds with diverse structure types were synthesized. • They are wide band gap semiconductors. • NaInSnS 4 and KInSnS 4 compounds undergo facile topotactic ion-exchange at room temperature.

On quadratic residue codes and hyperelliptic curves

Directory of Open Access Journals (Sweden)

David Joyner

2008-01-01

Full Text Available For an odd prime p and each non-empty subset S⊂GF(p, consider the hyperelliptic curve X S defined by y 2 =f S (x, where f S (x = ∏ a∈S (x-a. Using a connection between binary quadratic residue codes and hyperelliptic curves over GF(p, this paper investigates how coding theory bounds give rise to bounds such as the following example: for all sufficiently large primes p there exists a subset S⊂GF(p for which the bound |X S (GF(p| > 1.39p holds. We also use the quasi-quadratic residue codes defined below to construct an example of a formally self-dual optimal code whose zeta function does not satisfy the ``Riemann hypothesis.''

Measurement of Young’s modulus and residual stress of atomic layer deposited Al2O3 and Pt thin films

Science.gov (United States)

Purkl, Fabian; Daus, Alwin; English, Timothy S.; Provine, J.; Feyh, Ando; Urban, Gerald; Kenny, Thomas W.

2017-08-01

The accurate measurement of mechanical properties of thin films is required for the design of reliable nano/micro-electromechanical devices but is increasingly challenging for thicknesses approaching a few nanometers. We apply a combination of resonant and static mechanical test structures to measure elastic constants and residual stresses of 8-27 nm thick Al2O3 and Pt layers which have been fabricated through atomic layer deposition. Young’s modulus of poly-crystalline Pt films was found to be reduced by less than 15% compared to the bulk value, whereas for amorphous Al2O3 it was reduced to about half of its bulk value. We observed no discernible dependence of the elastic constant on thickness or deposition method for Pt, but the use of plasma-enhanced atomic layer deposition was found to increase Young’s modulus of Al2O3 by 10% compared to a thermal atomic layer deposition. As deposited, the Al2O3 layers had an average tensile residual stress of 131 MPa. The stress was found to be higher for thinner layers and layers deposited without the help of a remote plasma. No residual stress values could be extracted for Pt due to insufficient adhesion of the film without an underlying layer to promote nucleation.

Empirical parameters for solvent acidity, basicity, dipolarity, and polarizability of the ionic liquids [BMIM][BF4] and [BMIM][PF6].

Science.gov (United States)

del Valle, J C; García Blanco, F; Catalán, J

2015-04-02

The empirical solvent scales for polarizability (SP), dipolarity (SdP), acidity (SA), and basicity (SB) have been successfully used to interpret the solvatochromism of compounds dissolved in organic solvents and their solvent mixtures. Providing that the published solvatochromic parameters for the ionic liquids 1-(1-butyl)-3-methylimidazolium tetrafluoroborate, [BMIM][BF4] and 1-(1-butyl)-3-methylimidazolium hexafluorophosphate, [BMIM][PF6], are excessively widespread, their SP, SdP, SA, and SB values are measured herein at temperatures from 293 to 353 K. Four key points are emphasized herein: (i) the origin of the solvatochromic solvent scales--the gas phase, that is the absence of any medium perturbation--; (ii) the separation of the polarizability and dipolarity effects; (iii) the simplification of the probing process in order to obtain the solvatochromic parameters; and (iv) the SP, SdP, SA, and SB solvent scales can probe the polarizability, dipolarity, acidity, and basicity of ionic liquids as well as of organic solvents and water-organic solvent mixtures. From the multiparameter approach using the four pure solvent scales one can draw the conclusion that (a) the solvent influence of [BMIM][BF4] parallels that of formamide at 293 K, both of them miscible with water; (b) [BMIM][PF6] shows a set of solvatochromic parameters similar to that of chloroacetonitrile, both of them water insoluble; and (c) that the corresponding solvent acidity and basicity of the ionic liquids can be explained to a great extent from the cation species by comparing the empirical parameters of [BMIM](+) with those of the solvent 1-methylimidazole. The insolubility of [BMIM][PF6] in water as compared to [BMIM][BF4] is tentatively connected to some extent to the larger molar volume of the anion [PF6](-), and to the difference in basicity of [PF6](-) and [BF4](-).

(1S,3S,4S-tert-Butyl N-[1-benzyl-3-hydroxy-5-phenyl-4-(picolinamidopentyl]carbamate

Directory of Open Access Journals (Sweden)

Jian-Feng Zheng

2008-07-01

Full Text Available The title compound, C29H35N3O4, was obtained by the reaction of (2S,4S,5S-tert-butyl N-(4-amino-1-benzyl-3-hydroxy-5-phenylpentylcarbamate and picolinic acid using oxalyl chloride as a chlorinating reagent to activate the carboxyl group. In the crystal structure there are two molecules in the asymmetric unit, which are aligned edge-to-face. In one molecule, the pyridyl ring forms a dihedral angle of 22.0 (1° with the phenyl ring of the terminal benzyl group and 14.3 (1° with the other phenyl ring; in the other molecule, the corresponding angles are 12.1 (1 and 10.6 (1°, respectively. The packing is stabilized by intermolecular hydrogen bonds and C—H...π interactions.

Residual Strain Characteristics of Nickel-coated FBG Sensors

International Nuclear Information System (INIS)

Cho, Won-Jae; Hwang, A-Reum; Kim, Sang-Woo

2017-01-01

A metal-coated FBG (fiber Bragg grating) sensor has a memory effect, which can recall the maximum strains experienced by the structure. In this study, a nickel-coated FBG sensor was fabricated through electroless (i.e., chemical plating) and electroplating. A thickness of approximately 43 μm of a nickel layer was achieved. Then, we conducted cyclic loading tests for the fabricated nickel-coated FBG sensors to verify their capability to produce residual strains. The results revealed that the residual strain induced by the nickel coating linearly increased with an increase in the maximum strain experienced by the sensor. Therefore, we verified that a nickel-coated FBG sensor has a memory effect. The fabrication methods and the results of the cycle loading test will provide basic information and guidelines in the design of a nickel-coated FBG sensor when it is applied in the development of structural health monitoring techniques.

Residual Strain Characteristics of Nickel-coated FBG Sensors

Energy Technology Data Exchange (ETDEWEB)

Cho, Won-Jae; Hwang, A-Reum; Kim, Sang-Woo [Hankyong National Univ., Ansung (Korea, Republic of)

2017-07-15

A metal-coated FBG (fiber Bragg grating) sensor has a memory effect, which can recall the maximum strains experienced by the structure. In this study, a nickel-coated FBG sensor was fabricated through electroless (i.e., chemical plating) and electroplating. A thickness of approximately 43 μm of a nickel layer was achieved. Then, we conducted cyclic loading tests for the fabricated nickel-coated FBG sensors to verify their capability to produce residual strains. The results revealed that the residual strain induced by the nickel coating linearly increased with an increase in the maximum strain experienced by the sensor. Therefore, we verified that a nickel-coated FBG sensor has a memory effect. The fabrication methods and the results of the cycle loading test will provide basic information and guidelines in the design of a nickel-coated FBG sensor when it is applied in the development of structural health monitoring techniques.

Residual stress characterization of steel TIG welds by neutron diffraction and by residual magnetic stray field mappings

Energy Technology Data Exchange (ETDEWEB)

Stegemann, Robert, E-mail: Robert.Stegemann@bam.de [Bundesanstalt für Materialforschung und -prüfung (BAM), Unter den Eichen 87, 12200 Berlin (Germany); Cabeza, Sandra; Lyamkin, Viktor; Bruno, Giovanni; Pittner, Andreas [Bundesanstalt für Materialforschung und -prüfung (BAM), Unter den Eichen 87, 12200 Berlin (Germany); Wimpory, Robert; Boin, Mirko [HZB Helmholtz-Zentrum Berlin, Hahn-Meitner-Platz 1, 14109 Berlin (Germany); Kreutzbruck, Marc [Bundesanstalt für Materialforschung und -prüfung (BAM), Unter den Eichen 87, 12200 Berlin (Germany); IKT, University of Stuttgart, Pfaffenwaldring 32, 70569 Stuttgart (Germany)

2017-03-15

The residual stress distribution of tungsten inert gas welded S235JRC+C plates was determined by means of neutron diffraction (ND). Large longitudinal residual stresses with maxima around 600 MPa were found. With these results as reference, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors was discussed. The experiments performed indicate a correlation between changes in residual stresses (ND) and the normal component of local residual magnetic stray fields (GMR). Spatial variations in the magnetic field strength perpendicular to the welds are in the order of the magnetic field of the earth. - Highlights: • Comparison of magnetic microstructure with neutron diffraction stress analysis. • High spatial resolution magnetic stray field images of hypereutectoid TIG welds. • Spatial variations of the stray fields are below the magnetic field of the earth. • GMR spin valve gradiometer arrays adapted for the evaluation of magnetic microstructures. • Magnetic stray fields are closely linked to microstructure of the material.

Refuse-derived fuel from municipal solid waste residuals : a feasibility study[Manure, biosolids, and organic industrial/commercial residuals in land applications programs : improving beneficial reuse and protection of water quality

Energy Technology Data Exchange (ETDEWEB)

Sturgess, C.; Johnson, R. [Alberta Research Council, Vegreville, AB (Canada). Environmental Technologies; Schubert, J. [EWMC Operations, Edmonton, AB (Canada)

2007-07-01

Edmonton's Waste Management Centre (EWMC) consists of a composting plant and a materials recovery facility, which accepts over 230,000 tonnes of residential waste per year. It removes 74,000 tonnes of residuals from these two facilities through a series of processing and refining stages and landfilling. Alternative waste management strategies are being considered to handle these residuals as the city's landfill site is approaching its maximum capacity. One option that takes advantage of the high calorific value of these residues is gasification. To ensure consistent and uniform gasification, the residuals have to be processed to a homogenous feedstock. This paper outlined the steps that were taken to characterize the four distinct residual streams, process them to a refuse-derived fluff and pelletize mixtures of these four streams with specific additives. The paper discussed pellet criteria; feedstock preparation; the physical and chemical properties of the fluff and pelletized mixture; pelletization; and, cost estimates of the processing stages involved. Last, a summary of the project was provided. The first phase of the project has been completed. The second phase of the project involves the development of the optimum business case, which includes further cost assessment of the feedstock preparation stage; leasing commercial scale equipment to establish efficiency and robustness of the process; assessing an alternative feeding system for the gasification system; and evaluating methanol production using a catalyst to convert the syngas to methanol. 5 tabs., 4 figs.

Prevalence of Hepatitis B and C in US Air Force Basic Military Trainees

Science.gov (United States)

2017-08-29

REPORT TYPE 08/29/2017 Journal -4. TITLE AND SUBTITLE Prevalence ofliepatitis B and C in US Air Force Basic Military Trainees 6. AUTHOR(S) Capt...unlimited. 13. SUPPLEMENTARY NOTES 14. ABSTRACT 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF 18. NUMBER a. REPORT b.ABSTRACT c ...Prescnbed by ANSI Sld, Z3B.16 Adobe Prnfeodohal 7.0 Prevalence of Hepatitis Band C in US Air Force Basic Military Trainees from Blood Donations 2 3

Integration of Basic and Clinical Sciences: Faculty Perspectives at a U.S. Dental School.

Science.gov (United States)

van der Hoeven, Dharini; van der Hoeven, Ransome; Zhu, Liang; Busaidy, Kamal; Quock, Ryan L

2018-04-01

Although dental education has traditionally been organized into basic sciences education (first and second years) and clinical education (third and fourth years), there has been growing interest in ways to better integrate the two to more effectively educate students and prepare them for practice. Since 2012, The University of Texas School of Dentistry at Houston (UTSD) has made it a priority to improve integration of basic and clinical sciences, with a focus to this point on integrating the basic sciences. The aim of this study was to determine the perspectives of basic and clinical science faculty members regarding basic and clinical sciences integration and the degree of integration currently occurring. In October 2016, all 227 faculty members (15 basic scientists and 212 clinicians) were invited to participate in an online survey. Of the 212 clinicians, 84 completed the clinician educator survey (response rate 40%). All 15 basic scientists completed the basic science educator survey (response rate 100%). The majority of basic and clinical respondents affirmed the value of integration (93.3%, 97.6%, respectively) and reported regular integration in their teaching (80%, 86.9%). There were no significant differences between basic scientists and clinicians on perceived importance (p=0.457) and comfort with integration (p=0.240), but the basic scientists were more likely to integrate (p=0.039) and collaborate (p=0.021) than the clinicians. There were no significant differences between generalist and specialist clinicians on importance (p=0.474) and degree (p=0.972) of integration in teaching and intent to collaborate (p=0.864), but the specialists reported feeling more comfortable presenting basic science information (p=0.033). Protected faculty time for collaborative efforts and a repository of integrated basic science and clinical examples for use in teaching and faculty development were recommended to improve integration. Although questions might be raised about

Initial contents of residue quality parameters predict effects of larger soil fauna on decomposition of contrasting quality residues

Directory of Open Access Journals (Sweden)

Ratikorn Sanghaw

2017-10-01

Full Text Available A 52-week decomposition study employing the soil larger fauna exclusion technique through litter bags of two mesh sizes (20 and 0.135 mm was conducted in a long-term (18 yr field experiment. Organic residues of contrasting quality of N, lignin (L, polyphenols (PP and cellulose (CL all in grams per kilogram: rice straw (RS: 4.5N, 22.2L, 3.9PP, 449CL, groundnut stover (GN: 21.2N, 71.4L, 8.1PP, 361CL, dipterocarp leaf litter (DP: 5.1N, 303L, 68.9PP, 271CL and tamarind leaf litter (TM: 11.6N, 190L, 27.7PP, 212CL were applied to soil annually to assess and predict soil larger fauna effects (LFE on decomposition based on the initial contents of the residue chemical constituents. Mass losses in all residues were not different under soil fauna inclusion and exclusion treatments during the early stage (up to week 4 after residue incorporation but became significantly higher under the inclusion than the exclusion treatments during the later stage (week 8 onwards. LFE were highest (2–51% under the resistant DP at most decomposition stages. During the early stage (weeks 1–4, both the initial contents of labile (N and CL and recalcitrant C, and recalcitrant C interaction with labile constituents of residues showed significant correlations (r = 0.64–0.90 with LFE. In the middle stage (week 16, LFE under resistant DP and TM had significant positive correlations with L, L + PP and L/CL. They were also affected by these quality parameters as shown by the multiple regression analysis. In the later stages (weeks 26–52, the L/CL ratio was the most prominent quality parameter affecting LFE. Keywords: Mesofauna and macrofauna, Microorganisms, Recalcitrant and labile compounds, Residue chemical composition, Tropical sandy soil

Basic materials research programs at the U.S. Air Force Office of Scientific Research

International Nuclear Information System (INIS)

Carlson, Herbert C.; Goretta, K.C.

2006-01-01

The Air Force Office of Scientific Research (AFOSR) annually sponsors approximately 5000 research scientists at 1000 universities and laboratories, generating about 10,000 Ph.D. graduates per decade, all expected to publish their basic research findings in peer-reviewed journals. After a brief introduction of the nature of AFOSR's support to basic research in the U.S. and international scientific communities, work it supports at the frontiers of materials science is highlighted. One focused research theme that drives our investment is the MEANS program. It begins with the end in mind; materials are designed with practicable manufacture as an explicit initial goal. AFOSR's broad research portfolio comprises many materials. Nanotechnology efforts include optical materials that reduce distortion to the scale of the nanoparticles themselves. Advances in semiconductors include breakthroughs in Group III nitrides, some of which emanated from Asia under sponsorship from AFOSR's Asian office. Advances in structural materials include those for use at ultra-high temperatures and self-healing composites. The growing role of high-performance computing in design and study of functional, biological, and structural materials is also discussed

Residual symmetries in the presence of an EM background

International Nuclear Information System (INIS)

Carrion, H.L.; Rojas, M.; Toppan, F.

2002-08-01

The symmetry algebra of a QFT in the presence of an external EM background (named 'residual symmetry') is investigated within a Lie-algebraic, model independent scheme. Some results previously encountered in the literature are here extended. In particular we compute the symmetry algebra for a constant EM background in D = 3 and D = 4 dimensions. In D = 3 dimensions the residual symmetry algebra is isomorphic to u(1) +P c (2), with P c (2) the centrally extended 2-dimensional Poincare algebra. In D = 4 dimension the generic residual symmetry algebra is given by a seven-dimensional solvable Lie algebra which is explicitly computed. residual symmetry algebras are also computed for specific non-constant EM backgrounds. (author)

Residual symmetries in the presence of an EM background

Energy Technology Data Exchange (ETDEWEB)

Rojas Leyva, Moises Porfirio; Salazar, Hector Leny Carrion; Toppan, Francesco [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil)]. E-mail: mrojas, hleny, toppan@cbpf.br

2001-07-01

The symmetry algebra of a QFT in the presence of an external EM background (named 'residual symmetry') is investigated within a Lie-algebraic, model independent scheme. Some results previously encountered in the literature are here extended. In particular we compute the symmetry algebra for a constant EM background in D = 3 and D = 4 dimensions. In D = 3 dimensions the residual symmetry algebra is isomorphic to u(1) + P{sub c} (2) the centrally extended 2-dimensional Poincare algebra. In D=4 dimensions the generic residual symmetry algebra is given by a 7 dimensional solvable Lie algebra which is explicitly computed. Residual symmetry algebras are also computed for specific non-constant EM backgrounds. (author)

Laser spectroscopy of the 4s4p(3) P-2-4s3d(1) D-2 transition on magnetically trapped calcium atoms

NARCIS (Netherlands)

Dammalapati, U.; Norris, I.; Burrows, C.; Riis, E.

2011-01-01

Laser excitation of the 4s4p(3) P-2-4s3d(1) D-2 transition in atomic calcium has been observed and the wavelength determined to 1530.5298(6) nm. The metastable 4s4p(3) P-2 atoms were magnetically trapped in the quadrupole magnetic field of a magneto-optical trap. This state represents the only

EPA’s SPECIATE 4.4 Database:Development and Uses

Science.gov (United States)

SPECIATE is the U.S. Environmental Protection Agency's (EPA)repository of volatile organic gas and particulate matter (PM) speciation profiles for air pollution sources. EPA released SPECIATE 4.4 in early 2014 and, in total, the SPECIATE 4.4 database includes 5,728 PM, VOC, total...

Surgical treatment for residual or recurrent strabismus

Directory of Open Access Journals (Sweden)

Tao Wang

2014-12-01

Full Text Available Although the surgical treatment is a relatively effective and predictable method for correcting residual or recurrent strabismus, such as posterior fixation sutures, medial rectus marginal myotomy, unilateral or bilateral rectus re-recession and resection, unilateral lateral rectus recession and adjustable suture, no standard protocol is established for the surgical style. Different surgical approaches have been recommended for correcting residual or recurrent strabismus. The choice of the surgical procedure depends on the former operation pattern and the surgical dosages applied on the patients, residual or recurrent angle of deviation and the operator''s preference and experience. This review attempts to outline recent publications and current opinion in the management of residual or recurrent esotropia and exotropia.

Effects of the geophagous earthworm Metaphire guillelmi on sorption, mineralization, and bound-residue formation of 4-nonylphenol in an agricultural soil

International Nuclear Information System (INIS)

Shan, Jun; Wang, Yongfeng; Wang, Lianhong; Yan, Xiaoyuan; Ji, Rong

2014-01-01

Effects of earthworms on fate of nonylphenol (NP) are obscure. Using 14 C-4-NP 111 as a representative, we studied the fate of 4-NP in an agricultural soil with or without the earthworm Metaphire guillelmi and in fresh cast of the earthworm. Sorption of 4-NP on the cast (K d 1564) was significantly higher than on the parent soil (K d 1474). Mineralization of 4-NP was significantly lower in the cast (13.2%) and the soil with earthworms (10.4%) than in the earthworm-free soil (16.0%). One nitro metabolite of 4-NP 111 (2-nitro-4-NP 111 ) was identified in the soil and cast, and the presence of the earthworm significantly decreased its amounts. The presence of earthworm also significantly decreased formation of bound residues of 4-NP in the soil. Our results demonstrate that earthworms could significantly change the fate of 4-NP, underlining that earthworm effects should be considered when evaluating behavior and risk of 4-NP in soil. - Highlights: • The earthworm Metaphire guillelmi inhibited mineralization of 4-NP in the soil. • A less-polar metabolite of 4-NP (2-nitro-4-NP 111 ) was detected in the soil and cast. • The presence of earthworm reduced the amount of 2-nitro-4-NP 111 in the soil. • M. guillelmi significantly reduced formation of bound residues of 4-NP in the soil. - Earthworms significantly changed the fate of 4-NP, highlighting that effects of earthworm should be considered when evaluating the behavior and risk of 4-NP in soil

Analytical strategy for the detection of antibiotic residues in sheep and goat’s milk

International Nuclear Information System (INIS)

Beltrán, M.C.; Althaus, R.L.; Molina, A.; Berruga, M.I.; Molina, M.P.

2015-01-01

The use of antibiotics to treat mastitis and other infectious diseases in dairy sheep and goats is a widespread practice nowadays that can, when not properly applied, result in the contamination of the milk supply. Spanish legislation establishes the control of the presence of antibiotic residues in sheep and goat’s milk using screening methods that detect, at least, beta-lactam drugs. Microbial inhibitor tests using Geobacillus stearothermophilus var. calidolactis and specific receptor-binding assays are most widely employed for this purpose. The detection rates of screening tests routinely used in Spain have been calculated considering the frequency of use of veterinary drugs commonly applied in ovine and caprine livestock to treat and prevent mastitis as well as the test sensitivity toward these substances at safety levels. In general, the use of a single test allows detecting 62.8-82.4% of the antibiotics employed. For sheep milk, the total detection range achieved with microbial tests was significantly higher than that reached with rapid receptor tests. However, no significant differences between the two types of methods were found when goat's milk was analysed. In both types of milk, the simultaneous use of two screening tests with a different analytical basis increases the total detection range significantly, reaching values ≥ 90% in some cases (81.5-90.1% for sheep and 84.7-92.6% for goats). However, the periodical use of screening tests able to detect quinolones, macrolides or aminoglycosides would be recommended to carry out more efficient screening and ensure the safety of milk and dairy products from sheep and goats. (Author)

Analytical strategy for the detection of antibiotic residues in sheep and goat’s milk

Energy Technology Data Exchange (ETDEWEB)

Beltrán, M.C.; Althaus, R.L.; Molina, A.; Berruga, M.I.; Molina, M.P.

2015-07-01

The use of antibiotics to treat mastitis and other infectious diseases in dairy sheep and goats is a widespread practice nowadays that can, when not properly applied, result in the contamination of the milk supply. Spanish legislation establishes the control of the presence of antibiotic residues in sheep and goat’s milk using screening methods that detect, at least, beta-lactam drugs. Microbial inhibitor tests using Geobacillus stearothermophilus var. calidolactis and specific receptor-binding assays are most widely employed for this purpose. The detection rates of screening tests routinely used in Spain have been calculated considering the frequency of use of veterinary drugs commonly applied in ovine and caprine livestock to treat and prevent mastitis as well as the test sensitivity toward these substances at safety levels. In general, the use of a single test allows detecting 62.8-82.4% of the antibiotics employed. For sheep milk, the total detection range achieved with microbial tests was significantly higher than that reached with rapid receptor tests. However, no significant differences between the two types of methods were found when goat's milk was analysed. In both types of milk, the simultaneous use of two screening tests with a different analytical basis increases the total detection range significantly, reaching values ≥ 90% in some cases (81.5-90.1% for sheep and 84.7-92.6% for goats). However, the periodical use of screening tests able to detect quinolones, macrolides or aminoglycosides would be recommended to carry out more efficient screening and ensure the safety of milk and dairy products from sheep and goats. (Author)

Analytical strategy for the detection of antibiotic residues in sheep and goat’s milk

Directory of Open Access Journals (Sweden)

M. Carmen Beltrán

2015-03-01

Full Text Available The use of antibiotics to treat mastitis and other infectious diseases in dairy sheep and goats is a widespread practice nowadays that can, when not properly applied, result in the contamination of the milk supply. Spanish legislation establishes the control of the presence of antibiotic residues in sheep and goat’s milk using screening methods that detect, at least, beta-lactam drugs. Microbial inhibitor tests using Geobacillus stearothermophilus var. calidolactis and specific receptor-binding assays are most widely employed for this purpose. The detection rates of screening tests routinely used in Spain have been calculated considering the frequency of use of veterinary drugs commonly applied in ovine and caprine livestock to treat and prevent mastitis as well as the test sensitivity toward these substances at safety levels. In general, the use of a single test allows detecting 62.8-82.4% of the antibiotics employed. For sheep milk, the total detection range achieved with microbial tests was significantly higher than that reached with rapid receptor tests. However, no significant differences between the two types of methods were found when goat’s milk was analysed. In both types of milk, the simultaneous use of two screening tests with a different analytical basis increases the total detection range significantly, reaching values ≥ 90% in some cases (81.5-90.1% for sheep and 84.7-92.6% for goats. However, the periodical use of screening tests able to detect quinolones, macrolides or aminoglycosides would be recommended to carry out more efficient screening and ensure the safety of milk and dairy products from sheep and goats.

40 CFR 180.434 - Propiconazole; tolerances for residues.

Science.gov (United States)

2010-07-01

...: Commodity Parts per million Cranberry 1.0 Rice, wild, grain 0.5 (d) Indirect or inadvertent residues... 4.5 Pineapple, process residue 7.0 Pistachio 0.1 Rice, bran 15 Rice, grain 7.0 Rice, hulls 20 Rice...

Design, Synthesis and Antitumor Activity of Novel 4-Methyl-(3'S,4'S-cis-khellactone Derivatives

Directory of Open Access Journals (Sweden)

Taigang Liang

2013-04-01

Full Text Available An asymmetric synthesis of a series of novel 4-methyl-(3'S,4'S-cis-khellactone derivatives 3a–o is reported for the first time. Their structures were confirmed by 1H-NMR, 13C-NMR and MS. Their cytotoxic activity was evaluated by the MTT assay against three selected human cancer cell lines: HEPG-2 (human liver carcinoma, SGC-7901 (human gastric carcinoma, LS174T (human colon carcinoma. Some compounds showed high inhibitory activity against these human cancer cell lines. Among them, compound 3a exhibited strong cytotoxicity, with IC50 values ranging from 8.51 to 29.65 μM. The results showed that 4-methyl-cis-khellactone derivatives with S,S configuration could be a potential antitumor agents.

77 FR 5246 - Basic Energy Sciences Advisory Committee

Science.gov (United States)

2012-02-02

... DEPARTMENT OF ENERGY Basic Energy Sciences Advisory Committee AGENCY: Office of Science... of the Basic Energy Sciences Advisory Committee (BESAC). The Federal Advisory Committee Act (Pub. L... FURTHER INFORMATION CONTACT: Katie Perine; Office of Basic Energy Sciences; U.S. Department of Energy...

BASIC

DEFF Research Database (Denmark)

Hansen, Pelle Guldborg; Schmidt, Karsten

2017-01-01

De sidste 10 år har vi været vidner til opkomsten af et nyt evidensbaseret policy paradigme, Behavioural Public Policy (BPP), der søger at integrere teoretiske og metodiske indsigter fra adfærdsvidenskaberne i offentlig politikudvikling. Arbejdet med BPP har dog båret præg af, at være usystematisk...... BPP. Tilgangen består dels af den overordnede proces-model BASIC og dels af et iboende framework, ABCD, der er en model for systematisk adfærdsanalyse, udvikling, test og implementering af adfærdsrettede løsningskoncepter. Den samlede model gør det muligt for forskere såvel som offentligt ansatte...

The Analysis of Basic Public Service Supply Regional Equalization in China’s Provinces——Based on the Theil Index Evaluation

Science.gov (United States)

Liao, Zangyi

2017-12-01

Accomplishing the regional equalization of basic public service supply among the provinces in China is an important objective that can promote the people’s livelihood construction. In order to measure the problem which is about the non-equalization of basic public service supply, this paper takes these aspects as the first index, such as the infrastructure construction, basic education services, public employment services, public health service and social security service. At the same time, it cooperates with 16 index as the second index to construct the performance evaluation systems, and then use the Theil index to evaluate the performance in provinces that using the panel data from the year 2000 to 2012.

40 CFR 180.176 - Mancozeb; tolerances for residues.

Science.gov (United States)

2010-07-01

... Asparagus (negligible residue) 0.1 Banana 4.0 Banana, pulp 0.5 Barley, bran 20 Barley, flour 20 Barley..., straw 25 Onion, bulb 0.5 Papaya (whole fruit with no residue present in the edible pulp after the peel...

Residual stress in Ni-W electrodeposits

DEFF Research Database (Denmark)

Mizushima, Io; Tang, Peter Torben; Hansen, Hans Nørgaard

2006-01-01

In the present work, the residual stress in Ni–W layers electrodeposited from electrolytes based on NiSO4 and Na2WO4, is investigated. Citrate, glycine and triethanolamine were used as complexing agents, enabling complex formation between the nickel ion and tungstate. The results show that the type...... of complexing agent and the current efficiency have an influence on the residual stress. In all cases, an increase in tensile stress in the deposit with time after deposition was observed. Pulse plating could improve the stress level for the electrolyte containing equal amounts of citrate...

Characterization of Active Site Residues of Nitroalkane Oxidase†

Science.gov (United States)

Valley, Michael P.; Fenny, Nana S.; Ali, Shah R.; Fitzpatrick, Paul F.

2010-01-01

The flavoenzyme nitroalkane oxidase catalyzes the oxidation of primary and secondary nitrolkanes to the corresponding aldehydes and ketones plus nitrite. The structure of the enzyme shows that Serl71 forms a hydrogen bond to the flavin N5, suggesting that it plays a role in catalysis. Cys397 and Tyr398 were previously identified by chemical modification as potential active site residues. To more directly probe the roles of these residues, the S171A, S171V, S171T, C397S, and Y398F enzymes have been characterized with nitroethane as substrate. The C397S and Y398 enzymes were less stable than the wild-type enzyme, and the C397S enzyme routinely contained a substoichiometric amount of FAD. Analysis of the steady-state kinetic parameters for the mutant enzymes, including deuterium isotope effects, establishes that all of the mutations result in decreases in the rate constants for removal of the substrate proton by ~5-fold and decreases in the rate constant for product release of ~2-fold. Only the S171V and S171T mutations alter the rate constant for flavin oxidation. These results establish that these residues are not involved in catalysis, but rather are required for maintaining the protein structure. PMID:20056514

Ethanol Basics (Fact Sheet)

Energy Technology Data Exchange (ETDEWEB)

2015-01-01

Ethanol is a widely-used, domestically-produced renewable fuel made from corn and other plant materials. More than 96% of gasoline sold in the United States contains ethanol. Learn more about this alternative fuel in the Ethanol Basics Fact Sheet, produced by the U.S. Department of Energy's Clean Cities program.

Residues of tritium-labeled morantel in lactating dairy cattle

International Nuclear Information System (INIS)

Lynch, M.J.; Mosher, F.R.; Burnett, D.M.; Newby, T.J.

1987-01-01

Residues of morantel and its metabolites were monitored in plasma, urine, and milk of five lactating dairy cattle that received an oral dose of [4,4-pyrimidyl- 3 H 2 ]morantel tartrate at 10 mg/kg. Drug-related radioactivity peaked in plasma at 8 h and in milk by the second milking, postdose, and was 170 and 84 ng/mL, respectively. The fraction of total residues in milk convertible to the marker compound, N-methyl-1,3-propanediamine, was 0.38 on the basis of a comparison of the areas under the curves for total and marker residues. Five days after dosing, 3.9% of the total radioactivity in liver was recovered as tritium water. Total drug-related residues in this target tissue averaged 1.15 μg/g. About half of the drug-related residues in liver was unextractable and was classified by bound

Domain wise docking analyses of the modular chitin binding protein CBP50 from Bacillus thuringiensis serovar konkukian S4.

Science.gov (United States)

Sehar, Ujala; Mehmood, Muhammad Aamer; Hussain, Khadim; Nawaz, Salman; Nadeem, Shahid; Siddique, Muhammad Hussnain; Nadeem, Habibullah; Gull, Munazza; Ahmad, Niaz; Sohail, Iqra; Gill, Saba Shahid; Majeed, Summera

2013-01-01

This paper presents an in silico characterization of the chitin binding protein CBP50 from B. thuringiensis serovar konkukian S4 through homology modeling and molecular docking. The CBP50 has shown a modular structure containing an N-terminal CBM33 domain, two consecutive fibronectin-III (Fn-III) like domains and a C-terminal CBM5 domain. The protein presented a unique modular structure which could not be modeled using ordinary procedures. So, domain wise modeling using MODELLER and docking analyses using Autodock Vina were performed. The best conformation for each domain was selected using standard procedure. It was revealed that four amino acid residues Glu-71, Ser-74, Glu-76 and Gln-90 from N-terminal domain are involved in protein-substrate interaction. Similarly, amino acid residues Trp-20, Asn-21, Ser-23 and Val-30 of Fn-III like domains and Glu-15, Ala-17, Ser-18 and Leu-35 of C-terminal domain were involved in substrate binding. Site-directed mutagenesis of these proposed amino acid residues in future will elucidate the key amino acids involved in chitin binding activity of CBP50 protein.

Residual symmetries in the presence of an EM background

Energy Technology Data Exchange (ETDEWEB)

Carrion, H.L.; Rojas, M.; Toppan, F. [Centro Brasileiro de Pesquisas Fisicas (CBPF), Rio de Janeiro, RJ (Brazil)]. E-mail: hleny@cbpf.br; mrojas@cbpf.br; toppan@cbpf.br

2002-08-01

The symmetry algebra of a QFT in the presence of an external EM background (named 'residual symmetry') is investigated within a Lie-algebraic, model independent scheme. Some results previously encountered in the literature are here extended. In particular we compute the symmetry algebra for a constant EM background in D = 3 and D = 4 dimensions. In D = 3 dimensions the residual symmetry algebra is isomorphic to u(1) +P{sub c}(2), with P{sub c}(2) the centrally extended 2-dimensional Poincare algebra. In D = 4 dimension the generic residual symmetry algebra is given by a seven-dimensional solvable Lie algebra which is explicitly computed. residual symmetry algebras are also computed for specific non-constant EM backgrounds. (author)

The residual proton-neutron interaction and nuclear collectivity

International Nuclear Information System (INIS)

Casten, R.F.

1990-01-01

The essential role of the valence, residual p-n interaction in the development of collectivity, though long known in general terms, has recently become increasingly apparent. A brief review of the p-n interaction is given, including some very basic nuclear data that illustrate its effects and the phenomenological N p N n scheme and the P-factor. This is followed by a discussion of recent experimental extractions of p-n matrix elements throughout the periodic table and theoretical efforts to understand them, in terms of both Shell and Nilsson models. 20 refs., 13 figs

HCV Core Residues Critical for Infectivity Are Also Involved in Core-NS5A Complex Formation

Science.gov (United States)

Gawlik, Katarzyna; Baugh, James; Chatterji, Udayan; Lim, Precious J.; Bobardt, Michael D.; Gallay, Philippe A.

2014-01-01

Hepatitis C virus (HCV) infection is a major cause of liver disease. The molecular machinery of HCV assembly and particle release remains obscure. A better understanding of the assembly events might reveal new potential antiviral strategies. It was suggested that the nonstructural protein 5A (NS5A), an attractive recent drug target, participates in the production of infectious particles as a result of its interaction with the HCV core protein. However, prior to the present study, the NS5A-binding site in the viral core remained unknown. We found that the D1 domain of core contains the NS5A-binding site with the strongest interacting capacity in the basic P38-K74 cluster. We also demonstrated that the N-terminal basic residues of core at positions 50, 51, 59 and 62 were required for NS5A binding. Analysis of all substitution combinations of R50A, K51A, R59A, and R62A, in the context of the HCVcc system, showed that single, double, triple, and quadruple mutants were fully competent for viral RNA replication, but deficient in secretion of viral particles. Furthermore, we found that the extracellular and intracellular infectivity of all the mutants was abolished, suggesting a defect in the formation of infectious particles. Importantly, we showed that the interaction between the single and quadruple core mutants and NS5A was impaired in cells expressing full-length HCV genome. Interestingly, mutations of the four basic residues of core did not alter the association of core or NS5A with lipid droplets. This study showed for the first time that basic residues in the D1 domain of core that are critical for the formation of infectious extracellular and intracellular particles also play a role in core-NS5A interactions. PMID:24533158

Automated detection of residual cells after sex-mismatched stem-cell transplantation – evidence for presence of disease-marker negative residual cells

Directory of Open Access Journals (Sweden)

Johannes Tilman

2009-05-01

Full Text Available Abstract Background A new chimerism analysis based on automated interphase fluorescence in situ hybridization (FISH evaluation was established to detect residual cells after allogene sex-mismatched bone marrow or blood stem-cell transplantation. Cells of 58 patients were characterized as disease-associated due to presence of a bcr/abl-gene-fusion or a trisomy 8 and/or a simultaneous hybridization of gonosome-specific centromeric probes. The automatic slide scanning platform Metafer with its module MetaCyte was used to analyse 3,000 cells per sample. Results Overall 454 assays of 58 patients were analyzed. 13 of 58 patients showed residual recipient cells at one stage of more than 4% and 12 of 58 showed residual recipient cells less than 4%, respectively. As to be expected, patients of the latter group were associated with a higher survival rate (48 vs. 34 month. In only two of seven patients with disease-marker positive residual cells between 0.1–1.3% a relapse was observed. Besides, disease-marker negative residual cells were found in two patients without relapse at a rate of 2.8% and 3.3%, respectively. Conclusion The definite origin and meaning of disease-marker negative residual cells is still unclear. Overall, with the presented automatic chimerism analysis of interphase FISH slides, a sensitive method for detection of disease-marker positive residual cells is on hand.

Biotransformación del pelo residual de curtiembres

Directory of Open Access Journals (Sweden)

Ruth Viviana Numpaque

2016-12-01

Full Text Available La industria de curtiembres genera una alta carga contaminante representada por residuos líquidos, sólidos y gaseosos. Entre los residuos sólidos, el pelo residual es vertido directamente al río Bogotá y/o en rellenos sanitarios, desencadenando serios conflictos de orden ambiental, social y económico. El objetivo de esta investigación fue evaluar la capacidad de los microorganismos del EM y Agroplux en la transformación del pelo residual en compost. Se evaluaron tres tratamientos con pelo residual y materiales orgánicos de plaza en diferentes porcentajes y dos controles, utilizando el diseño completamente al azar, con tres repeticiones. Durante el compostaje se determinaron las variables temperatura, formación de agregados, pH y conductividad eléctrica. El desarrollo de la temperatura ocurrió en ciclos que concordaron con los volteos y re-inoculaciones. En el tercer ciclo el mayor incremento de temperatura fue obtenido en los tres tratamientos, cuando ya se había agotado la mayor parte de los residuos orgánicos. La formación de agregados indicó que el proceso se llevó a efecto principalmente en el tratamiento con 20% de pelo residual más 80% de residuos orgánicos. Además de su color oscuro y la ausencia de olor y fragmentos, el compost producido mediante dicho tratamiento mostró la conductividad eléctrica más baja y un pH casi neutro. Se concluye que los microorganismos del EM y Agroplux tienen capacidad para transformar el pelo residual en compost y por lo tanto representan una alternativa viable para la continuación del funcionamiento de la industria de curtiembres en Villapinzón (Cundinamarca y en otras regiones de Colombia.

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A K [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1998-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled

The potential of agro-industrial residues and municipal solid waste for production of biogas and electricity in Tanzania

Energy Technology Data Exchange (ETDEWEB)

Kivaisi, A.K. [Univ. of Dar es Salaam, Botany Dept., Applied Microbiology Unit (Tanzania, United Republic of)

1997-12-31

This paper gives an overview of the energy demands in Tanzania, and highlights the current serious shortage of electricity. Government strategy to alleviate the problem include exploitation of the country`s big natural gas reserves for power generation, and utilization of the renewable energies such as solar, wind and biogas. Important agro-industrial residues and municipal solid wastes with large potentials for anaerobic converstion into biogas and electricity have been identified and quantified. Tanzania is estimated to generate about 615,000 organic matter from coffee, sisal, sugar and cereal residues and households in main towns are estimated to generate about 600,000 tons of organic matter annually. Laboratory scale determinations of methane yields from the residues gave 400 m{sup 3} CH{sub 4}/ton VS of sisal pulp; 400 m{sup 3} CH{sub 4}/ton VS of sisal production wastewater; 400 m{sup 3} CH{sub 4}/ton VS of Robusta coffee solid waste, 350 m{sup 3} CH{sub 4}/ton VS of sugar processing wastewater; 250 m{sup 3} CH{sub 4}/ton VS of sugar filter mat, 450 m{sup 3} CH{sub 4}/ton VS maize bran and 300 m{sup 3} CH{sub 4}/ton VS of mixed household waste. Based on these results the estimated total annual potential electricity production from these residues is 1.4 million MW. The total oil substitution from these residues has been estimated at 0.35 million tonnes crude diesel oil per annum equivalent to 2% of the total energy consumption in Tanzania. Case studies onthe coffee and sisal processing factories indicate that exploitation of the residues for the production of electricity on site these factories is feasible. Utilization of agro-industrial residues and municipal waste for biogas production has enormous potential for reduction of environmental pollution. The potential substitution of fossil fuel with biogas represents an annual reduction in the net CO{sub 2} emission to the atmosphere of approximately 1.3 million tonnes. By treating the residues in controlled

Electronic properties of GaV 4 S 8

Indian Academy of Sciences (India)

... different in GaV4S8-1 and GaV4S8-2. This statement is strongly supported by the calculated bandwidth per cluster in GaV4S8 (∼0.342 eV in GaV4S8-1 and ∼0.374 eV in GaV4S8-2). A negative magnetoresistance (MR) is also found around 43 K in GaV4S8-2 at 6.0 T magnetic field associated with structural transition.

Critical roles of isoleucine-364 and adjacent residues in a hydrophobic gate control of phospholipid transport by the mammalian P4-ATPase ATP8A2.

Science.gov (United States)

Vestergaard, Anna L; Coleman, Jonathan A; Lemmin, Thomas; Mikkelsen, Stine A; Molday, Laurie L; Vilsen, Bente; Molday, Robert S; Dal Peraro, Matteo; Andersen, Jens Peter

2014-04-08

P4-ATPases (flippases) translocate specific phospholipids such as phosphatidylserine from the exoplasmic leaflet of the cell membrane to the cytosolic leaflet, upholding an essential membrane asymmetry. The mechanism of flipping this giant substrate has remained an enigma. We have investigated the importance of amino acid residues in transmembrane segment M4 of mammalian P4-ATPase ATP8A2 by mutagenesis. In the related ion pumps Na(+),K(+)-ATPase and Ca(2+)-ATPase, M4 moves during the enzyme cycle, carrying along the ion bound to a glutamate. In ATP8A2, the corresponding residue is an isoleucine, which recently was found mutated in patients with cerebellar ataxia, mental retardation, and dysequilibrium syndrome. Our analyses of the lipid substrate concentration dependence of the overall and partial reactions of the enzyme cycle in mutants indicate that, during the transport across the membrane, the phosphatidylserine head group passes near isoleucine-364 (I364) and that I364 is critical to the release of the transported lipid into the cytosolic leaflet. Another M4 residue, N359, is involved in recognition of the lipid substrate on the exoplasmic side. Our functional studies are supported by structural homology modeling and molecular dynamics simulations, suggesting that I364 and adjacent hydrophobic residues function as a hydrophobic gate that separates the entry and exit sites of the lipid and directs sequential formation and annihilation of water-filled cavities, thereby enabling transport of the hydrophilic phospholipid head group in a groove outlined by the transmembrane segments M1, M2, M4, and M6, with the hydrocarbon chains following passively, still in the membrane lipid phase.

Attenuation of cancer-initiating cells stemness properties by abrogating S100A4 calcium binding ability in head and neck cancers.

Science.gov (United States)

Cheng, Li-Hao; Hung, Kai-Feng; Huang, Tung-Fu; Hsieh, Hsin-Pei; Wang, Shu-Ying; Huang, Chih-Yang; Lo, Jeng-Fan

2016-11-29

S100A4 is a calcium-binding protein capable of promoting epithelial-mesenchymal transition. Previously, we have demonstrated that S100A4 is required to sustain the head and neck cancer-initiating cells (HN-CICs) subpopulation. In this study, to further investigate the molecular mechanism, we established the head and neck squamous cell carcinoma (HNSCC) cell lines stably expressing mutant S100A4 proteins with defective calcium-binding sites on either N-terminal (NM) or C-terminal (CM), or a deletion of the last 15 amino-acid residues (CD). We showed that the NM, CM and CD harboring sphere cells that were enriched with HN-CICs population exhibited impaired stemness and malignant properties in vitro, as well as reduced tumor growth ability in vivo. Mechanistically, we demonstrated that mutant S100A4 proteins decreased the promoter activity of Nanog, likely through inhibition of p53. Moreover, the biophysical analyses of purified recombinant mutant S100A4 proteins suggest that both NM and CM mutant S100A4 were very similar to the WT S100A4 with subtle difference on the secondary structure, and that the CD mutant protein displayed the unexpected monomeric form in the solution phase.Taken together, our results suggest that both the calcium-binding ability and the C-terminal region of S100A4 are important for HN-CICs to sustain its stemness property and malignancy, and that the mechanism could be mediated by repressing p53 and subsequently activating the Nanog expression.

Efficient identification of critical residues based only on protein structure by network analysis.

Directory of Open Access Journals (Sweden)

Michael P Cusack

2007-05-01

Full Text Available Despite the increasing number of published protein structures, and the fact that each protein's function relies on its three-dimensional structure, there is limited access to automatic programs used for the identification of critical residues from the protein structure, compared with those based on protein sequence. Here we present a new algorithm based on network analysis applied exclusively on protein structures to identify critical residues. Our results show that this method identifies critical residues for protein function with high reliability and improves automatic sequence-based approaches and previous network-based approaches. The reliability of the method depends on the conformational diversity screened for the protein of interest. We have designed a web site to give access to this software at http://bis.ifc.unam.mx/jamming/. In summary, a new method is presented that relates critical residues for protein function with the most traversed residues in networks derived from protein structures. A unique feature of the method is the inclusion of the conformational diversity of proteins in the prediction, thus reproducing a basic feature of the structure/function relationship of proteins.

Immobilization in ceramic waste forms of the residues from treatment of mixed wastes

International Nuclear Information System (INIS)

Oversby, V.M.; van Konynenburg, R.A.; Glassley, W.E.; Curtis, P.G.

1993-11-01

The Environmental Restoration and Waste Management Applied Technology Program at LLNL is developing a Mixed Waste Management Facility to demonstrate treatment technologies that provide an alternative to incineration. As part of that program, we are developing final waste forms using ceramic processing methods for the immobilization of the treatment process residues. The ceramic phase assemblages are based on using Synroc D as a starting point and varying the phase assemblage to accommodate the differences in chemistry between the treatment process residues and the defense waste for which Synroc D was developed. Two basic formulations are used, one for low ash residues resulting from treatment of organic materials contaminated with RCRA metals, and one for high ash residues generated from the treatment of plastics and paper products. Treatment process residues are mixed with ceramic precursor materials, dried, calcined, formed into pellets at room temperature, and sintered at 1150 to 1200 degrees C to produce the final waste form. This paper discusses the chemical composition of the waste streams and waste forms, the phase assemblages that serve as hosts for inorganic waste elements, and the changes in waste form characteristics as a function of variation in process parameters

Applied exposure modeling for residual radioactivity and release criteria

International Nuclear Information System (INIS)

Lee, D.W.

1989-01-01

The protection of public health and the environment from the release of materials with residual radioactivity for recycle or disposal as wastes without radioactive contents of concern presents a formidable challenge. Existing regulatory criteria are based on technical judgment concerning detectability and simple modeling. Recently, exposure modeling methodologies have been developed to provide a more consistent level of health protection. Release criteria derived from the application of exposure modeling methodologies share the same basic elements of analysis but are developed to serve a variety of purposes. Models for the support of regulations for all applications rely on conservative interpretations of generalized conditions while models developed to show compliance incorporate specific conditions not likely to be duplicated at other sites. Research models represent yet another type of modeling which strives to simulate the actual behavior of released material. In spite of these differing purposes, exposure modeling permits the application of sound and reasoned principles of radiation protection to the release of materials with residual levels of radioactivity. Examples of the similarities and differences of these models are presented and an application to the disposal of materials with residual levels of uranium contamination is discussed. 5 refs., 2 tabs

Trimaximal TM1 neutrino mixing in S4 with spontaneous CP violation

International Nuclear Information System (INIS)

Luhn, Christoph

2013-01-01

The measurement of the reactor angle by the Daya Bay and RENO experiments in 2012 has ruled out the tri-bimaximal paradigm. Adopting an S 4 family symmetry, we propose direct models of the trimaximal type TM 1 in which the tri-bimaximal Klein symmetry of the neutrino sector is broken to a residual Z 2 symmetry. In such a scenario, the solar mixing angle is decreased compared to its tri-bimaximal value by about 1°, thus bringing it in excellent agreement with experimental observation. The atmospheric mixing angle, on the other hand, depends on the CP violating Dirac phase δ. Imposing CP conservation in the family symmetry limit, we show how to break the CP symmetry via flavon VEVs with well-defined complex phases, so that sizable deviations of the atmospheric angle from maximal mixing, consistent with the latest global fits, are produced

Improved GaSb surfaces using a (NH{sub 4}){sub 2}S/(NH{sub 4}){sub 2}S0{sub 4} solution

Energy Technology Data Exchange (ETDEWEB)

Murape, D.M., E-mail: Davison.Murape@live.nmmu.ac.za [Department of Physics, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa); Eassa, N.; Nyamhere, C.; Neethling, J.H. [Department of Physics, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa); Betz, R. [Department of Chemistry, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa); Coetsee, E.; Swart, H.C. [Department of Physics, University of the Free State, PO Box 339, Bloemfontein 9300 (South Africa); Botha, J.R.; Venter, A. [Department of Physics, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa)

2012-05-15

Bulk (1 0 0) n-GaSb surfaces have been treated with a sulphur based solution ((NH{sub 4}){sub 2}S/(NH{sub 4}){sub 2}SO{sub 4}) to which sulphur has been added, not previously reported for the passivation of GaSb surfaces. Au/n-GaSb Schottky barrier diodes (SBDs) fabricated on the treated material show significant improvement compared to that of the similar SBDs on the as-received material as evidenced by the lower ideality factor (n), higher barrier height ({phi}{sub b}) and lower contact resistance obtained. Additionally, the reverse leakage current, although not saturating, has been reduced by almost an order of magnitude at -0.2 V. The sample surfaces were studied by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The native oxide, Sb-O, present on the as-received material is effectively removed on treating with ([(NH{sub 4}){sub 2}S/(NH{sub 4}){sub 2}SO{sub 4}]+S) and (NH{sub 4}){sub 2}S. Analysis of the as-received surface by XPS, prior to and after argon sputtering, suggests that the native oxide layer is {<=}8.5 nm.

The effect of various S-alkylating agents on the chromatographic behavior of cysteine-containing peptides in reversed-phase chromatography.

Science.gov (United States)

Jiang, Xuehui; Shamshurin, Dmitry; Spicer, Vic; Krokhin, Oleg V

2013-02-01

We investigate the influence of various alkylation chemistries on the reversed phase (RP) HPLC behavior of Cys-containing peptides under the most popular RP-HPLC conditions used in proteomics: C18 phases with trifluoroacetic acid (TFA) or formic acid (FA) as the ion pairing modifiers, and separation at pH 10. Akylating agents studied are iodoacetamide (IAM), iodoacetic acid (IAA), 4-vinylpyridine (4-VP), acrylamide (AA) and methyl methanethiosulfonate (MMTS). These were compared against the retention of identical peptides without alkylation, i.e. free cysteines. The intrinsic hydrophobicity values of the Cys residue under formic acid conditions for these modifications were found to increase in the following order: 4-VPalkylated Cys using TFA eluent. Switching to a basic condition dramatically decreases the retention of free cysteine and IAA-alkylated analytes due to the ionization of side-chains. The opposite effect is observed for 4-VP, which become neutral at basic pHs. The careful measurement of the hydrophobic contributions for these residues is vital to the development of accurate peptide retention prediction models; the incorporation of these modifications into our Sequence Specific Retention Calculator model is presented. Copyright © 2013. Published by Elsevier B.V.

46 CFR 129.220 - Basic safety.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Basic safety. 129.220 Section 129.220 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS ELECTRICAL INSTALLATIONS General Requirements § 129.220 Basic safety. (a) Electrical equipment and installations must be suitable...

Angular distributions of evaporation residues from near-barrier fusion of 32,36S on a ≅100 nuclei

International Nuclear Information System (INIS)

Borges, A.M.

1986-01-01

The angular distributions of evaporation residues from near-barrier fusion of 32,36 S ions with 92,94,96,98,100 Mo, 100,101,102,104 Ru, 103 Rh, and 104,105,106,108,110 Pd were measured in the range of 3 to 11 degrees in the laboratory system. The relative yield of the four most abundant exit evaporation channels has been extracted for all target-projectile combination at two bombarding energies, by fitting the angular distributions expected for each channel as obtained from the Monte-Carlo program TRANMI to the measured angular distribution of the evaporation residues. The total detection efficiency for the Munich-RF-Recoil Spectrometer was obtained from the relative yields, taking into account the effect due to multiple scattering, and compared with that obtained previously from the recoil velocity distributions. (orig./HSI) [de

Basic scattering theory

International Nuclear Information System (INIS)

Queen, N.M.

1978-01-01

This series of lectures on basic scattering theory were given as part of a course for postgraduate high energy physicists and were designed to acquaint the student with some of the basic language and formalism used for the phenomenological description of nuclear reactions and decay processes used for the study of elementary particle interactions. Well established and model independent aspects of scattering theory, which are the basis of S-matrix theory, are considered. The subject is considered under the following headings; the S-matrix, cross sections and decay rates, phase space, relativistic kinematics, the Mandelstam variables, the flux factor, two-body phase space, Dalitz plots, other kinematic plots, two-particle reactions, unitarity, the partial-wave expansion, resonances (single-channel case), multi-channel resonances, analyticity and crossing, dispersion relations, the one-particle exchange model, the density matrix, mathematical properties of the density matrix, the density matrix in scattering processes, the density matrix in decay processes, and the helicity formalism. Some exercises for the students are included. (U.K.)

Hydrogen bond strengths in phosphorylated and sulfated amino acid residues.

Directory of Open Access Journals (Sweden)

Chaya Rapp

Full Text Available Post-translational modification by the addition of an oxoanion functional group, usually a phosphate group and less commonly a sulfate group, leads to diverse structural and functional consequences in protein systems. Building upon previous studies of the phosphoserine residue (pSer, we address the distinct nature of hydrogen bonding interactions in phosphotyrosine (pTyr and sulfotyrosine (sTyr residues. We derive partial charges for these modified residues and then study them in the context of molecular dynamics simulation of model tripeptides and sulfated protein complexes, potentials of mean force for interacting residue pairs, and a survey of the interactions of modified residues among experimental protein structures. Overall, our findings show that for pTyr, bidentate interactions with Arg are particularly dominant, as has been previously demonstrated for pSer. sTyr interactions with Arg are significantly weaker, even as compared to the same interactions made by the Glu residue. Our work sheds light on the distinct nature of these modified tyrosine residues, and provides a physical-chemical foundation for future studies with the goal of understanding their roles in systems of biological interest.

Incorporation of QCD effects in basic corrections of the electroweak theory

CERN Document Server

Fanchiotti, Sergio; Sirlin, Alberto; Fanchiotti, Sergio; Kniehl, Bernd; Sirlin, Alberto

1993-01-01

We study the incorporation of QCD effects in the basic electroweak corrections \\drcar, \\drcarw, and \\dr. They include perturbative \\Ord{\\alpha\\alpha_s} contributions and $t\\bar{t}$ threshold effects. The latter are studied in the resonance and Green-function approaches, in the framework of dispersion relations that automatically satisfy relevant Ward identities. Refinements in the treatment of the electroweak corrections, in both the \\ms\\ and the on-shell schemes of renormalization, are introduced, including the decoupling of the top quark in certain amplitudes, its effect on $\\hat{e}^2(\\mz)$ and \\sincarmz, the incorporation of recent results on the leading irreducible \\Ord{\\alpha^2} corrections, and simple expressions for the residual, i.e.\\ ``non-electromagnetic'', parts of \\drcar, \\drcarw, and \\dr. The results are used to obtain accurate values for \\mw\\ and \\sincarmz, as functions of \\mt\\ and \\mh. The higher-order effects induce shifts in these parameters comparable to the expected experimental accuracy, a...

Saturation Mutagenesis of the HIV-1 Envelope CD4 Binding Loop Reveals Residues Controlling Distinct Trimer Conformations.

Directory of Open Access Journals (Sweden)

Maria Duenas-Decamp

2016-11-01

Full Text Available The conformation of HIV-1 envelope (Env glycoprotein trimers is key in ensuring protection against waves of neutralizing antibodies generated during infection, while maintaining sufficient exposure of the CD4 binding site (CD4bs for viral entry. The CD4 binding loop on Env is an early contact site for CD4 while penetration of a proximal cavity by CD4 triggers Env conformational changes for entry. The role of residues in the CD4 binding loop in regulating the conformation of the trimer and trimer association domain (TAD was investigated using a novel saturation mutagenesis approach. Single mutations identified, resulted in distinct trimer conformations affecting CD4bs exposure, the glycan shield and the TAD across diverse HIV-1 clades. Importantly, mutations that improve access to the CD4bs without exposing the immunodominant V3 loop were identified. The different trimer conformations identified will affect the specificity and breadth of nabs elicited in vivo and are important to consider in design of Env immunogens for vaccines.

The Effect of Fungicide Residues and Yeast Assimilable Nitrogen on Fermentation Kinetics and H2S Production during Cider Fermentation

OpenAIRE

Boudreau IV, Thomas Francis

2016-01-01

The Virginia cider industry has grown rapidly in the past decade, and demands research-based recommendations for cider fermentation. This study evaluated relationships between the unique chemistry of apples and production of hydrogen sulfide (H2S) in cider fermentations. Yeast assimilable nitrogen (YAN) concentration and composition and residual fungicides influence H2S production by yeast during fermentation, but these factors have to date only been studied in wine grape fermentations. This ...

Platelet antiheparin activity. The isolation and characterisation of platelet factor 4 released from thrombin-aggregated washed human platelets and its dissociation into subunits and the isolation of membrane-bound antiheparin activity.

Science.gov (United States)

Moore, S; Pepper, D S; Cash, J D

1975-02-27

Platelet factor 4 was isolated by gel filtration from the soluble release products of thrombin-aggregated washed human platelets as a proteoglycan-platelet factor 4 complex of molecular weight 358 000, Stokes radius (r-s) of 14.0 nm, sedimentation coefficient (s) of 7.1 S and frictional ratio (f/f-o) of 3.04. The complex was dissociated at high ionic strength (I equals 0.75) and the proteoglycan separated from platelet factor 4 by gel filtration. Platelet factor 4 had a molecular weight of 27 100, r-s of 2.52 nm, s of 2.4 S and f/f-o of 1.26, was insoluble under physiological conditions but readily soluble at pH 3. Under these conditions platelet factor 4 dissociated into four subunits with a molecular weight of 6900, r-s of 1.92 nm, s of 0.8 S, and f/f-o of 1.52. Qualitative N-terminal amino acid analysis showed the presence of glutamic acid or glutamine as the major end group. Platelet factor 4 was compared with protamine sulphate, which has similar biological properties, by electrophoresis at pH 2.2, in which both migrated as single bands but with differing mobility, and by amino acid analysis which showed a more normal distribution of residues than occurred in protamine sulphate. Of the basic amino acids platelet factor 4 (molecular weight 27 100) contained 5.97% arginine, 3.18% histidine, and 12.31% lysine compared to protamine sulphate with 64.2% arginine, 0.6% lysine and no histidine. A partial specific volume (v) of 0.747 was calculated for platelet factor 4 from its amino acid analysis. A membrane fraction with antiheparin activity, an isopycnic density of 1.090-1.110 and r-s of 15-35 nm, was also isolated by sucrose density gradient centrifugation from the ultrasonicated insoluble platelet residue remaining after thrombin-induced aggregation of washed human platelets. Trypsin treatment of the membrane fraction neither solubilised nor destroyed the activity.

Assessment of long-term leaching from waste incineration air-pollution-control residues

DEFF Research Database (Denmark)

Astrup, Thomas; Mosbæk, Hans; Christensen, Thomas Højlund

2006-01-01

Assessment of long-term leaching from MSWI air-pollution-control (APC) residues is discussed with respect to use in environmental impact assessment, such as life-cycle assessment (LCA). A method was proposed for estimating leaching as a function of the liquid-to-solid (L/S) ratio in a long......-term perspective (L/S 5000l/kg). Data for changes in residue pH as a function of L/S was used in combination with pH dependent leaching data to predict leachate concentrations of Al, Ca, Cd, Ba, Mg, Ni, Pb, S, Pb, V and Zn as a function of L/S. Mass balance calculations were used to determine the element fractions...... leached with respect to L/S. The estimated long-term leaching from a semi-dry residue and a fly ash was compared with short-term leaching determined by batch tests at L/S 10l/kg, both carbonated and non-carbonated versions of the residues were investigated. Generally, very high L/S ratios above 2000l...

40 CFR 180.464 - Dimethenamid; tolerances for residues.

Science.gov (United States)

2010-07-01

...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances...)-acetamide, applied as either the 90:10 or 50:50 S:R isomers, in or on the following food commodities... Pumpkin 0.01 Squash, winter 0.01 (d) Indirect or inadvertent residues. [Reserved] [65 FR 51551, Aug. 24...

Solid Phase Microextraction (SPME in Determination of Pesticide Residues in Soil Samples

Directory of Open Access Journals (Sweden)

Rada Đurović

2011-01-01

Full Text Available The basic principles and application possibilities of the methods based on solid phase microextraction (SPME in the analysis of pesticide residues in soil samples are presented in the paper. The most important experimental parameters which affect SPME efficacy inpesticide determination (type and thickness of microextraction fiber, duration of microextraction,temperature at which it is conducted, effect of addition of salts (the effect of efflorescence,temperature and time of desorption, the choice of optimal solvent for pesticide exctraction from the soil and the optimal number of extraction steps, as well as general guidelines for their optimization are also shown. In the end, current applications of SPMEmethods in the analysis of pesticide residues in soil samples are presented.

Compost and residues from biogas plant as potting substrates for salt-tolerant and salt-sensitive plants

Energy Technology Data Exchange (ETDEWEB)

Cam Van, Do Thi

2013-08-01

Compost and residues from biogas plant have been increasingly recognized as potting substrates in horticulture. To investigate the suitability of both materials to grow salt tolerant plants in 2010 a pot experiment was conducted in the greenhouse of INRES-Plant nutrition, University of Bonn. Ryegrass (Lolium perenne L.), rape (Brassica napus) and sunflower (Helianthus annuus) were chosen as experimental plants. To reduce the high salt content compost and residues from biogas plant were leached. To improve physical characteristics of raw materials, additives including Perlite, Styromull, Hygromull, Lecaton, Peat, Cocofiber were incorporated into compost or residues from biogas plant with the volumetric ratio of 4:1. Plant growth (DM) and nutrient uptake (N, P, K, Mg, Ca, Na and S) of the experimental plants grown in compost-based or residue-based substrates with and without additives and standard soil as a control were determined. Preliminary results reveal that origin compost and residues from biogas plant without leaching are suitable potting substrates for those plants. For compost leaching may not be recommended while for residues from biogas plant the effect of leaching was not distinct and needs further investigations. The incorporation of additives into the basic materials partially resulted in higher plant dry matter yield and nutrient uptake. However, differences between the additives on both parameters were mainly insignificant. Incorporation of Hygromull or Peat, especially into residues from biogas plant favored plant growth and enhanced total nutrient uptake. In 2011, pot experiments were continued with the salt-sensitive ornamental plants, Pelargonium (Pelargonium zonale Toro) and Salvia (Salvia splendens). Two separate experiments were carried out for the mixtures of compost and additives (SPS standard soil type 73 based on Peat, Hygromull or Cocofiber) with different volumetric ratios (4:1, 1:1, 1:4) and the mixtures of Peat incorporated with small

Residue number systems theory and applications

CERN Document Server

Mohan, P V Ananda

2016-01-01

This new and expanded monograph improves upon Mohan's earlier book, Residue Number Systems (Springer, 2002) with a state of the art treatment of the subject. Replete with detailed illustrations and helpful examples, this book covers a host of cutting edge topics such as the core function, the quotient function, new Chinese Remainder theorems, and large integer operations. It also features many significant applications to practical communication systems and cryptography such as FIR filters and elliptic curve cryptography. Starting with a comprehensive introduction to the basics and leading up to current research trends that are not yet widely distributed in other publications, this book will be of interest to both researchers and students alike.

Generation and validation of ORIGEN-S libraries for depletion and transmutation calculations based on JEF2.2 and EAF3 basic data

Energy Technology Data Exchange (ETDEWEB)

Hoogenboom, J.E. [Delft Univ. of Technol. (Netherlands). Interfaculty Reactor Inst.; Kloosterman, J.L. [Netherlands Energy Research Foundation ECN, P.O. Box 1, 1755 ZG Petten (Netherlands)

1997-07-01

The data libraries for light elements, actinides and fission products of the ORIGEN-S code for depletion and transmutation calculations in the SCALE4.1 computer code system have been updated with respect to cross-section data, radioactive-decay data and fission-product yield data using JEF2.2 as the basic data source and EAF3 as an additional source. This required the fission-product library to be extended with 201 new fission-product nuclides or isomeric states. The effect of the update of different quantities involved is evaluated with a burn-up benchmark. When ORIGEN-S is used as a stand-alone code, i.e. without regular update of cross-sections of the major nuclides due to changes in the neutron spectrum during burn-up, the results show appreciable differences in actinide and fission-product densities due to the cross-section update. The effects of updates of decay data and fission-product yields are generally small, but with noticeable exceptions. The update of fission and capture reaction energies gives a small but systematic change in actinide and fission-product concentration. The new ORIGEN-S libraries have also been converted for use with the SCALE4.2 package. (orig.)

Generation and validation of ORIGEN-S libraries for depletion and transmutation calculations based on JEF2.2 and EAF3 basic data

International Nuclear Information System (INIS)

Hoogenboom, J.E.

1997-01-01

The data libraries for light elements, actinides and fission products of the ORIGEN-S code for depletion and transmutation calculations in the SCALE4.1 computer code system have been updated with respect to cross-section data, radioactive-decay data and fission-product yield data using JEF2.2 as the basic data source and EAF3 as an additional source. This required the fission-product library to be extended with 201 new fission-product nuclides or isomeric states. The effect of the update of different quantities involved is evaluated with a burn-up benchmark. When ORIGEN-S is used as a stand-alone code, i.e. without regular update of cross-sections of the major nuclides due to changes in the neutron spectrum during burn-up, the results show appreciable differences in actinide and fission-product densities due to the cross-section update. The effects of updates of decay data and fission-product yields are generally small, but with noticeable exceptions. The update of fission and capture reaction energies gives a small but systematic change in actinide and fission-product concentration. The new ORIGEN-S libraries have also been converted for use with the SCALE4.2 package. (orig.)

Determination of Pesticides Residues in Cucumbers Grown in Greenhouse and the Effect of Some Procedures on Their Residues.

Science.gov (United States)

Leili, Mostafa; Pirmoghani, Amin; Samadi, Mohammad Taghi; Shokoohi, Reza; Roshanaei, Ghodratollah; Poormohammadi, Ali

2016-11-01

The objective of this study was to determine the residual concentrations of ethion and imidacloprid in cucumbers grown in greenhouse. The effect of some simple processing procedures on both ethion and imidacloprid residues were also studied. Ten active greenhouses that produce cucumber were randomly selected. Ethion and imidacloprid as the most widely used pesticides were measured in cucumber samples of studied greenhouses. Moreover, the effect of storing, washing, and peeling as simple processing procedures on both ethion and imidacloprid residues were investigated. One hour after pesticide application; the maximum residue levels (MRLs) of ethion and imidacloprid were higher than that of Codex standard level. One day after pesticide application, the levels of pesticides were decreased about 35 and 31% for ethion and imidacloprid, respectively, which still were higher than the MRL. Washing procedure led to about 51 and 42.5% loss in ethion and imidacloprid residues, respectively. Peeling procedure also led to highest loss of 93.4 and 63.7% in ethion and imidacloprid residues, respectively. The recovery for both target analytes was in the range between 88 and 102%. The residue values in collected samples one hour after pesticides application were higher than standard value. The storing, washing, and peeling procedures lead to the decrease of pesticide residues in greenhouse cucumbers. Among them, the peeling procedure has the greatest impact on residual reduction. Therefore, these procedures can be used as simple and effective processing techniques for reducing and removing pesticides from greenhouse products before their consumption.

Characterization of active site residues of nitroalkane oxidase.

Science.gov (United States)

Valley, Michael P; Fenny, Nana S; Ali, Shah R; Fitzpatrick, Paul F

2010-06-01

The flavoenzyme nitroalkane oxidase catalyzes the oxidation of primary and secondary nitroalkanes to the corresponding aldehydes and ketones plus nitrite. The structure of the enzyme shows that Ser171 forms a hydrogen bond to the flavin N5, suggesting that it plays a role in catalysis. Cys397 and Tyr398 were previously identified by chemical modification as potential active site residues. To more directly probe the roles of these residues, the S171A, S171V, S171T, C397S, and Y398F enzymes have been characterized with nitroethane as substrate. The C397S and Y398 enzymes were less stable than the wild-type enzyme, and the C397S enzyme routinely contained a substoichiometric amount of FAD. Analysis of the steady-state kinetic parameters for the mutant enzymes, including deuterium isotope effects, establishes that all of the mutations result in decreases in the rate constants for removal of the substrate proton by approximately 5-fold and decreases in the rate constant for product release of approximately 2-fold. Only the S171V and S171T mutations alter the rate constant for flavin oxidation. These results establish that these residues are not involved in catalysis, but rather are required for maintaining the protein structure. 2009 Elsevier Inc. All rights reserved.

The basic construction materials industry and today’s vast housing shortage

Directory of Open Access Journals (Sweden)

Oteiza, I.

2008-12-01

Full Text Available This paper documents some of the aspects of the major challenge facing world-wide building: humanity's daunting shortage of basic housing, monographically focusing on what this means for the basic building materials industry. These needs have created the greatest demand ever for ex-novo solutions and an exponential increase in slum rehabilitation and improvement, translated here into the need for construction materials and more specifically, cement, as the emblematic component of buildings.El trabajo aborda en forma documentada, algunos aspectos del mayor de los retos que tiene planteado a nivel cosmopolita el sector de la edificación: las ingentes necesidades de habitabilidad básica que padece la humanidad, centrándose en forma monográfica en lo que ello supone para la industria de materiales básicos de edificación. Necesidades que se traducen en la mayor demanda histórica de soluciones ex-novo y en el aumento exponencial de rehabilitación y mejora de tugurios, que los autores traducen en necesidades de materiales de construcción, y de forma más concreta, de cemento, como material emblemático de la edificación.El trabajo, mediante el análisis de casos, muestra la muy diferente repercusión que tienen los materiales sobre los presupuestos finales de lo ejecutado, según se trate del mundo desarrollado (MD o de países en vías de desarrollo (PVD. Por otra parte, estudia la incidencia general del sector 'informal' de la construcción, concluyendo que éste, en muchos países, es el consumidor mayoritario de materiales -specialmente cemento-y que a nivel mundial los PVD lo son tanto en producción como en consumo.

Residual stresses

International Nuclear Information System (INIS)

Sahotra, I.M.

2006-01-01

The principal effect of unloading a material strained into the plastic range is to create a permanent set (plastic deformation), which if restricted somehow, gives rise to a system of self-balancing within the same member or reaction balanced by other members of the structure., known as residual stresses. These stresses stay there as locked-in stresses, in the body or a part of it in the absence of any external loading. Residual stresses are induced during hot-rolling and welding differential cooling, cold-forming and extruding: cold straightening and spot heating, fabrication and forced fitting of components constraining the structure to a particular geometry. The areas which cool more quickly develop residual compressive stresses, while the slower cooling areas develop residual tensile stresses, and a self-balancing or reaction balanced system of residual stresses is formed. The phenomenon of residual stresses is the most challenging in its application in surface modification techniques determining endurance mechanism against fracture and fatigue failures. This paper discusses the mechanism of residual stresses, that how the residual stresses are fanned and what their behavior is under the action of external forces. Such as in the case of a circular bar under limit torque, rectangular beam under limt moment, reclaiming of shafts welds and peening etc. (author)

Magnetic solid-phase extraction based on carbon nanotubes for the determination of polyether antibiotic and s-triazine drug residues in animal food with LC-MS/MS.

Science.gov (United States)

Liu, Xiaoxing; Xie, Shuyu; Ni, Tengteng; Chen, Dongmei; Wang, Xu; Pan, Yuanhu; Wang, Yulian; Huang, Lingli; Cheng, Guyue; Qu, Wei; Liu, Zhenli; Tao, Yanfei; Yuan, Zonghui

2017-06-01

Carbon nanotubes-magnetic nanoparticles, comprising ferroferric oxide nanoparticles and carbon nanotubes, were prepared through a simple one-step synthesis method and subsequently applied to magnetic solid-phase extraction for the determination of polyether antibiotic and s-triazine drug residues in animal food coupled with liquid chromatography with tandem mass spectrometry. The nanocomposites were characterized by transmission electron microscopy, X-ray diffraction, and vibrating sample magnetometry. The components within the nanocomposites endowed the material with high extraction performance and manipulative convenience. Compared with carbon nanotubes, the as-prepared carbon nanotubes-magnetic nanoparticles showed better extraction and separation efficiencies for polyether antibiotics and s-triazine drugs thanks to the contribution of the iron-containing magnetic nanoparticles. Various experimental parameters affecting the extraction efficiency had been investigated in detail. Under the optimal conditions, the good linearity ranging from 1 to 200 μg/kg for diclazuril, toltrazuril, toltrazuril sulfone, lasalocid, monensin, salinomycin, narasin, nanchangmycin, and maduramicin, low limits of detection ranging from 1 to 5 μg/kg, and satisfactory spiked recoveries (77.1-91.2%, with the inter relative standard deviation values from 4.0 to 12.2%) were shown. It was confirmed that this novel method was an efficient pretreatment and enrichment procedure and could be successfully applied for extraction and determination of polyether and s-triazine drug residues in complex matrices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hanford tank residual waste - Contaminant source terms and release models

International Nuclear Information System (INIS)

Deutsch, William J.; Cantrell, Kirk J.; Krupka, Kenneth M.; Lindberg, Michael L.; Jeffery Serne, R.

2011-01-01

Highlights: → Residual waste from five Hanford spent fuel process storage tanks was evaluated. → Gibbsite is a common mineral in tanks with high Al concentrations. → Non-crystalline U-Na-C-O-P ± H phases are common in the U-rich residual. → Iron oxides/hydroxides have been identified in all residual waste samples. → Uranium release is highly dependent on waste and leachant compositions. - Abstract: Residual waste is expected to be left in 177 underground storage tanks after closure at the US Department of Energy's Hanford Site in Washington State, USA. In the long term, the residual wastes may represent a potential source of contamination to the subsurface environment. Residual materials that cannot be completely removed during the tank closure process are being studied to identify and characterize the solid phases and estimate the release of contaminants from these solids to water that might enter the closed tanks in the future. As of the end of 2009, residual waste from five tanks has been evaluated. Residual wastes from adjacent tanks C-202 and C-203 have high U concentrations of 24 and 59 wt.%, respectively, while residual wastes from nearby tanks C-103 and C-106 have low U concentrations of 0.4 and 0.03 wt.%, respectively. Aluminum concentrations are high (8.2-29.1 wt.%) in some tanks (C-103, C-106, and S-112) and relatively low ( 2 -saturated solution, or a CaCO 3 -saturated water. Uranium release concentrations are highly dependent on waste and leachant compositions with dissolved U concentrations one or two orders of magnitude higher in the tests with high U residual wastes, and also higher when leached with the CaCO 3 -saturated solution than with the Ca(OH) 2 -saturated solution. Technetium leachability is not as strongly dependent on the concentration of Tc in the waste, and it appears to be slightly more leachable by the Ca(OH) 2 -saturated solution than by the CaCO 3 -saturated solution. In general, Tc is much less leachable (<10 wt.% of the

Thermal oxidation of medical Ti6Al4V blasted with ceramic particles: Effects on the microstructure, residual stresses and mechanical properties.

Science.gov (United States)

Lieblich, M; Barriuso, S; Multigner, M; González-Doncel, G; González-Carrasco, J L

2016-02-01

Roughening of Ti6Al4V by blasting with alumina or zirconia particles improves the mechanical fixation of implants by increasing the surface area available for bone/implant apposition. Additional thermal oxidation treatments of the blasted alloy have already shown to be a complementary low-cost solution to enhancing the in vitro biocompatibility and corrosion resistance of the alloy. In this work, the effects of oxidation treatment on a grit blasted Ti6Al4V biomedical alloy have been analysed in order to understand the net effect of the combined treatments on the alloy fatigue properties. Synchrotron radiation diffraction experiments have been performed to measure residual stresses before and after the treatments and microstructural and hardness changes have been determined. Although blasting of Ti6Al4V with small spherical zirconia particles increases the alloy fatigue resistance with respect to unblasted specimens, fatigue strength after oxidation decreases below the unblasted value, irrespective of the type of particle used for blasting. Moreover, at 700°C the as-blasted compressive residual stresses (700MPa) are not only fully relaxed but even moderate tensile residual stresses, of about 120MPa, are found beneath the blasted surfaces. Contrary to expectations, a moderate increase in hardness occurs towards the blasted surface after oxidation treatments. This can be attributed to the fact that grit blasting modifies the crystallographic texture of the Ti6Al4V shifting it to a random texture, which affects the hardness values as shown by additional experiments on cold rolled samples. The results indicate that the oxidation treatment performed to improve biocompatibility and corrosion resistance of grit blasted Ti6Al4V should be carried out with caution since the alloy fatigue strength can be critically diminished below the value required for high load-bearing components. Copyright © 2015 Elsevier Ltd. All rights reserved.

Biotransformation of (-)-(1R,4S)-Menthone and (+)-(1S,4R)-Menthone by the Common Cutworm Spodoptera litura Larvae.

Science.gov (United States)

Marumoto, Shinsuke; Okuno, Yoshiharu; Hagiwara, Yuki; Miyazawa, Mitsuo

2017-08-01

Using biotransformation as a biocatalytic process has the advantage of being able to proceed under mild conditions and with high regio- and enantioselectivity. This study investigated the biotransformation of (-)-(1R,4S)-menthone (1) and (+)-(1S,4R)-menthone (2) by Spodoptera litura larvae. Compound 1 was converted to (-)-(1R,4S)-7-hydroxymenthone (1-1), (+)-(1R,3S,4S)-7-hydroxyneomenthol (1-2) and (-)-(1R,4S,8R)-p-menth-3-one-9-oic acid (1-3). The metabolism of substrate 2 generated three enantiomers of the above metabolites, designated as 2-1 to 2-3, respectively. The C-9 position of (-)-menthone and (+)-menthone was oxidized to carboxylic acid by S. litura, which is a metabolic pathway not observed in any other example of biocatalysis.

Short-term impact of dry olive mill residue addition to soil on the resident microbiota

Czech Academy of Sciences Publication Activity Database

Sampedro, I.; Giubilei, M. A.; Cajthaml, Tomáš; Federici, E.; Federici, F.; Petruccioli, M.; D´Annibale, A.

2009-01-01

Roč. 100, č. 23 (2009), s. 6098-6106 ISSN 0960-8524 R&D Projects: GA MŠk LC06066 Institutional research plan: CEZ:AV0Z50200510 Keywords : Dry olive mill residue * Microbial community profiling * Toxicity Subject RIV: EE - Microbiology, Virology Impact factor: 4.253, year: 2009

Mechanistic basis for type 2 long QT syndrome caused by KCNH2 mutations that disrupt conserved arginine residues in the voltage sensor.

Science.gov (United States)

McBride, Christie M; Smith, Ashley M; Smith, Jennifer L; Reloj, Allison R; Velasco, Ellyn J; Powell, Jonathan; Elayi, Claude S; Bartos, Daniel C; Burgess, Don E; Delisle, Brian P

2013-05-01

KCNH2 encodes the Kv11.1 channel, which conducts the rapidly activating delayed rectifier K+ current (I Kr) in the heart. KCNH2 mutations cause type 2 long QT syndrome (LQT2), which increases the risk for life-threatening ventricular arrhythmias. LQT2 mutations are predicted to prolong the cardiac action potential (AP) by reducing I Kr during repolarization. Kv11.1 contains several conserved basic amino acids in the fourth transmembrane segment (S4) of the voltage sensor that are important for normal channel trafficking and gating. This study sought to determine the mechanism(s) by which LQT2 mutations at conserved arginine residues in S4 (R531Q, R531W or R534L) alter Kv11.1 function. Western blot analyses of HEK293 cells transiently expressing R531Q, R531W or R534L suggested that only R534L inhibited Kv11.1 trafficking. Voltage-clamping experiments showed that R531Q or R531W dramatically altered Kv11.1 current (I Kv11.1) activation, inactivation, recovery from inactivation and deactivation. Coexpression of wild type (to mimic the patients' genotypes) mostly corrected the changes in I Kv11.1 activation and inactivation, but deactivation kinetics were still faster. Computational simulations using a human ventricular AP model showed that accelerating deactivation rates was sufficient to prolong the AP, but these effects were minimal compared to simply reducing I Kr. These are the first data to demonstrate that coexpressing wild type can correct activation and inactivation dysfunction caused by mutations at a critical voltage-sensing residue in Kv11.1. We conclude that some Kv11.1 mutations might accelerate deactivation to cause LQT2 but that the ventricular AP duration is much more sensitive to mutations that decrease I Kr. This likely explains why most LQT2 mutations are nonsense or trafficking-deficient.

Peptides containing internal residues of pyroglutamic acid: proton NMR characteristics

International Nuclear Information System (INIS)

Khan, S.A.

1986-01-01

The proton NMR characteristics of internal pyroglutamic acid (Glp; 5-oxoproline) residues in seven tripeptides of the general structure Boc-Xxx-Glp-Yyy-NH 2 were studied. In general, the chemical shifts of several diagnostic protons moved downfield on going from the Glu-containing peptides (Boc-Xxx-Glu-Yyy-NH 2 ) to the corresponding Glp-containing peptides. The C-2 proton of the Xxx residue was shifted by about 1.1 ppm. The N-2 proton of the Yyy residue was shifted by about 0.5 ppm. The C-2 proton of the Glx residue itself was shifted by about 0.5 ppm. One of the Glx C-3 protons was also shifted by about 0.5 ppm, but the other remained essentially unchanged. Finally, the Glx C-4 protons were shifted by about 0.3 ppm. Internal Glu residues are readily converted chemically into internal Glp residues. This conversion also occurs as a side reaction during HP cleavage of the protecting group from Glu(OBzl) residues. The spontaneous fragmentation of serum proteins C3, C4 and λ 2 -macroglobulin under denaturing conditions is probably due to regioselective hydrolysis of an internal Glp residue formed in each of these proteins upon denaturation. These proton NMR characteristics may be useful in establishing the presence of internal Glp residues in synthetic and natural peptides

Voice disorders in residual paracoccidioidomycosis in upper airways and digestive tract.

Science.gov (United States)

da Costa, Ananda Dutra; Vargas, Amanda Pereira; Lucena, Marcia Mendonça; Ruas, Ana Cristina Nunes; Braga, Fernanda da Silva Santos; Bom-Braga, Mateus Pereira; Bom-Braga, Frederico Pereira; do Valle, Antonio Carlos Francesconi; Igreja, Ricardo Pereira; Valete-Rosalino, Cláudia Maria

Paracoccidioidomycosis (PCM) is a systemic mycosis of acute and chronic evolution, caused by species belonging to the genus Paracoccidioides. It is considered the most prevalent systemic endemic mycosis in Latin America, with cases in the tropical and subtropical regions. Residual PCM refers to the fibrotic scar sequelae resulting from the disease treatment which, when associated with collagen accumulation, leads to functional and anatomic alterations in the organs. The aim of this study was to evaluate the vocal function of patients with residual PCM in upper airways and digestive tract. We performed a cross-sectional study in 2010 in a cohort of 21 patients with residual PCM in upper airways and digestive tract. The average age was 49.48±9.1 years, and only two (9.5%) patients were female. The study was performed in the 1-113 month-period (median 27) after the end of drug treatment. Five (23.8%) patients had alterations in the larynx as a sequela of the disease. However, all patients had vocal changes in vocal auditory perceptual analysis by GRBASI scale. The computerized acoustic analysis using the software Vox Metria, showed that 11 patients (52.4%) presented alterations in jitter, 15 (71.4%) in shimmer, 8 (38.1%) in F0, 4 (19%) in glottal to noise excitation (GNE), 7 (33.3%) in the presence of noise and 12 (57.1%) in the presence of vibratory irregularity. The great frequency of alterations in residual PCM suggests that the patients in such phase could benefit from a multidisciplinary treatment, offering them integral monitoring of the disease, including speech rehabilitation after the PCM is healed. Copyright © 2017 Asociación Española de Micología. Publicado por Elsevier España, S.L.U. All rights reserved.

The space of harmonic maps of S2 into S4

International Nuclear Information System (INIS)

Loo, B.

1989-05-01

Every branched superminimal surface of area 4πd in S 4 is shown to arise from a pair of meromorphic functions (f 1 ,f 2 ) of bidegree (d,d) such that f 1 and f 2 have the same ramification divisor. Conditions under which branched superminimal surfaces can be generated from such pairs of functions are derived. For each d ≥ 1 the space of harmonic maps (i.e branched superminimal immersions) of S 2 into S 4 of harmonic degree d is shown to be a connected space of complex dimension 2d+4. (author). 18 refs

Basic Health, Women’s Health, and Mental Health Among Internally Displaced Persons in Nyala Province, South Darfur, Sudan

Science.gov (United States)

Kim, Glen; Torbay, Rabih; Lawry, Lynn

2007-01-01

Objectives. We assessed basic health, women’s health, and mental health among Sudanese internally displaced persons in South Darfur. Methods. In January 2005, we surveyed 6 registered internally displaced persons camps in Nyala District. Using systematic random sampling, we surveyed 1293 households, interviewing 1 adult female per household (N=1274); respondents’ households totaled 8643 members. We inquired about respondents’ mental health, opinions on women’s rights, and the health status of household members. Results. A majority of respondents had access to rations, shelter, and water. Sixty-eight percent (861 of 1266) used no birth control, and 53% (614 of 1147) reported at least 1 unattended birth. Thirty percent (374 of 1238) shared spousal decisions on timing and spacing of children, and 49% (503 of 1027) reported the right to refuse sex. Eighty-four percent (1043 of 1240) were circumcised. The prevalence of major depression was 31% (390 of 1253). Women also expressed limited rights regarding marriage, movement, and access to health care. Eighty-eight percent (991 of 1121) supported equal educational opportunities for women. Conclusions. Humanitarian aid has relieved a significant burden of this displaced population’s basic needs. However, mental and women’s health needs remain largely unmet. The findings indicate a limitation of sexual and reproductive rights that may negatively affect health. PMID:17138925

Preparation, properties and anticancer effects of mixed As{sub 4}S{sub 4}/ZnS nanoparticles capped by Poloxamer 407

Energy Technology Data Exchange (ETDEWEB)

Bujňáková, Z., E-mail: bujnakova@saske.sk [Institute of Geotechnics, Slovak Academy of Sciences, Watsonova 45, 04001 Košice (Slovakia); Baláž, M. [Institute of Geotechnics, Slovak Academy of Sciences, Watsonova 45, 04001 Košice (Slovakia); Zdurienčíková, M.; Sedlák, J. [Cancer Research Institute, BMC Slovak Academy of Sciences, Dúbravská 9, 84505 Bratislava (Slovakia); Čaplovičová, M. [STU Centre for Nanodiagnostics, Slovak University of Technology, Vazovova 5, 81243 Bratislava (Slovakia); Čaplovič, Ľ. [Faculty of Materials Science and Technology, Slovak University of Technology, Paulínska 16, 91724 Trnava (Slovakia); Dutková, E.; Zorkovská, A.; Turianicová, E.; Baláž, P. [Institute of Geotechnics, Slovak Academy of Sciences, Watsonova 45, 04001 Košice (Slovakia); Shpotyuk, O. [Scientific Research Company “Carat”, Stryjska 202, 79031 Lviv (Ukraine); Institute of Physics, Jan Dlugosz University, Armii Krajowej 13/15., 42200 Czestochowa (Poland); and others

2017-02-01

Arsenic sulfide compounds have a long history of application in a traditional medicine. In recent years, realgar has been studied as a promising drug in cancer treatment. In this study, the arsenic sulfide (As{sub 4}S{sub 4}) nanoparticles combined with zinc sulfide (ZnS) ones in different molar ratio have been prepared by a simple mechanochemical route in a planetary mill. The successful synthesis and structural properties were confirmed and followed via X-ray diffraction and high-resolution transmission electron microscopy measurements. The morphology of the particles was studied via scanning electron microscopy and transmission electron microscopy methods and the presence of nanocrystallites was verified. For biological tests, the prepared As{sub 4}S{sub 4}/ZnS nanoparticles were further milled in a circulation mill in a water solution of Poloxamer 407 (0.5 wt%), in order to cover the particles with this biocompatible copolymer and to obtain stable nanosuspensions with unimodal distribution. The average size of the particles in the nanosuspensions (~ 120 nm) was determined by photon cross-correlation spectroscopy method. Stability of the nanosuspensions was determined via particle size distribution and zeta potential measurements, confirming no physico-chemical changes for several months. Interestingly, with the increasing amount of ZnS in the sample, the stability was improved. The anti-cancer effects were tested on two melanoma cell lines, A375 and Bowes, with promising results, confirming increased efficiency of the samples containing both As{sub 4}S{sub 4} and ZnS nanocrystals. - Highlights: • Mixed As{sub 4}S{sub 4}/ZnS nanoparticles were prepared by dry milling in the first stage • Stable nanosuspensions of As{sub 4}S{sub 4}/ZnS nanoparticles capped by Poloxamer 407 were prepared by wet milling in the second stage • ZnS in the samples is beneficial: higher values of S{sub A}, stability, solubility and anticancer activity were improved.

Basic Training of Student’s Outdoor Club Increases Muscle Mass after Five Weeks of Exercise in Males

Directory of Open Access Journals (Sweden)

Novie Salsabila

2015-03-01

Full Text Available Background: Aerobic and anaerobic exercises, may lead to increase muscle mass. The aim of this study was to determine the change in muscle mass during basic training of students’ outdoor club. Methods: This was an observational analytic study to college students who joined basic training of students’ outdoor club for 19 weeks. Subjects consisted of 17 male and 15 female students, measured five times consecutively by using Body Fat/Hydration monitor scale, with Bioelectrical Impedance Analysis principle. Data collection was performed five times, from February to July 2012 in Bandung. Statistical analysis was processed using Analysis of Variance (ANOVA. Results: The result in males showed the mean 43.35±3.15 on the initial measurement. The muscle mass further increased significantly after five, ten, fifteen, and nineteen weeks of exercise (43.73±3.18 (p0.05; 38.08±1.67 (p>0.05 ; 38.23±1.52 (p>0.05 ; 38.61±1.52 (p<0.05 vs 37.77±2.00 respectively. Conclusion: Basic training of student’s outdoor club increases muscle mass significantly after five weeks of exercise in males, but not in females

Isotope aided studies of pesticide residues during food processing. Report of a final research co-ordination meeting held in Bangkok, Thailand, 31 January - 4 February 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

The use of agrochemicals in general and pesticides in particular has greatly aided crop production, protected man from diseases, decreased losses of stored grains and has generally improved man`s welfare. One of the steps in ensuring safety of pesticides is adequate monitoring programmes for residue levels in food products and the agricultural environment. Oil-bearing plants often receive heavy pesticide treatment and known to accumulate high concentration of pesticide residues. Technical documents included in this volume report effect of refining or processing of various oil crops like soybean, olive oil, coconut, rapeseed, sunflower cottonseed corn, peanut oil on {sup 14}C-compound pesticide residues.

Clinicopathological outcomes of preoperative chemoradiotherapy using S-1 plus Irinotecan for T4 lower rectal cancer.

Science.gov (United States)

Beppu, Naohito; Yoshie, Hidenori; Kimura, Fumihiko; Aihara, Tsukasa; Doi, Hiroshi; Kamikonya, Norihiko; Matsubara, Nagahide; Tomita, Naohiro; Yanagi, Hidenori; Yamanaka, Naoki

2016-07-01

To investigate the clinicopathological outcomes of patients with T4 lower rectal cancer treated using preoperative chemoradiotherapy with S-1 plus Irinotecan. Between 2005 and 2011, 35 patients with T4M0 lower rectal cancer, diagnosed initially as T4a in 12 and as T4b in 23, were treated with 45 Gy of radiotherapy concomitantly with S-1 plus Irinotecan. The median follow-up period was 50.6 months (range 2-123 months). A total of 32 patients (91.4 %) completed the radiotherapy and 26 (74.3 %) completed the full chemotherapy regimen. Radical surgery was then performed in 33 (94.3 %) of the 35 patients after the exclusion of two patients, who had macroscopic residual disease. The pathological diagnosis was downstaged from T4a to ypT0-3 in all 12 of those patients (100 %) and from T4b to ypT0-4a in 20 of those 23 patients (87.0 %). The tumor regression grade of 1a/1b/2/3 (complete response) was 10/8/15/2, respectively. In terms of long-term survival, the 5-year local relapse-free survival rate was 74.8 % and the recurrence-free survival rate was 52.0 %. This regimen may result in favorable downstaging. Moreover, in this series, pathological evidence of involvement of adjacent organs was rare following preoperative chemoradiotherapy, in the patients with disease diagnosed as T4b at the initial staging.

Actinide recovery from pyrochemical residues

International Nuclear Information System (INIS)

Avens, L.R.; Clifton, D.G.; Vigil, A.R.

1984-01-01

A new process for recovery of plutonium and americium from pyrochemical waste has been demonstrated. It is based on chloride solution anion exchange at low acidity, which eliminates corrosive HCl fumes. Developmental experiments of the process flowsheet concentrated on molten salt extraction (MSE) residues and gave >95% plutonium and >90% americium recovery. The recovered plutonium contained 6 = from high chloride-low acid solution. Americium and other metals are washed from the ion exchange column with 1N HNO 3 -4.8M NaCl. The plutonium is recovered, after elution, via hydroxide precipitation, while the americium is recovered via NaHCO 3 precipitation. All filtrates from the process are discardable as low-level contaminated waste. Production-scale experiments are now in progress for MSE residues. Flow sheets for actinide recovery from electrorefining and direct oxide reduction residues are presented and discussed

Actinide recovery from pyrochemical residues

International Nuclear Information System (INIS)

Avens, L.R.; Clifton, D.G.; Vigil, A.R.

1985-05-01

We demonstrated a new process for recovering plutonium and americium from pyrochemical waste. The method is based on chloride solution anion exchange at low acidity, or acidity that eliminates corrosive HCl fumes. Developmental experiments of the process flow chart concentrated on molten salt extraction (MSE) residues and gave >95% plutonium and >90% americium recovery. The recovered plutonium contained 6 2- from high-chloride low-acid solution. Americium and other metals are washed from the ion exchange column with lN HNO 3 -4.8M NaCl. After elution, plutonium is recovered by hydroxide precipitation, and americium is recovered by NaHCO 3 precipitation. All filtrates from the process can be discardable as low-level contaminated waste. Production-scale experiments are in progress for MSE residues. Flow charts for actinide recovery from electro-refining and direct oxide reduction residues are presented and discussed

Syntheses, structural variants and characterization of AInM′S{sub 4} (A=alkali metals, Tl; M′ = Ge, Sn) compounds; facile ion-exchange reactions of layered NaInSnS{sub 4} and KInSnS{sub 4} compounds

Energy Technology Data Exchange (ETDEWEB)

Yohannan, Jinu P.; Vidyasagar, Kanamaluru, E-mail: kvsagar@iitm.ac.in

2016-06-15

Ten AInM′S{sub 4} (A=alkali metals, Tl; M′= Ge, Sn) compounds with diverse structure types have been synthesized and characterized by single crystal and powder X-ray diffraction and a variety of spectroscopic methods. They are wide band gap semiconductors. KInGeS{sub 4}(1-β), RbInGeS{sub 4}(2), CsInGeS{sub 4}(3-β), TlInGeS{sub 4}(4-β), RbInSnS{sub 4}(8-β) and CsInSnS{sub 4}(9) compounds with three-dimensional BaGa{sub 2}S{sub 4} structure and CsInGeS{sub 4}(3-α) and TlInGeS{sub 4}(4-α) compounds with a layered TlInSiS{sub 4} structure have tetrahedral [InM′S{sub 4}]{sup −} frameworks. On the other hand, LiInSnS{sub 4}(5) with spinel structure and NaInSnS{sub 4}(6), KInSnS{sub 4}(7), RbInSnS{sub 4}(8-α) and TlInSnS{sub 4}(10) compounds with layered structure have octahedral [InM′S{sub 4}]{sup −} frameworks. NaInSnS{sub 4}(6) and KInSnS{sub 4}(7) compounds undergo facile topotactic ion-exchange, at room temperature, with various mono-, di- and tri-valent cations in aqueous medium to give rise to metastable layered phases. - Graphical abstract: NaInSnS{sub 4} and KInSnS{sub 4} compounds undergo, in aqueous medium at room temperature, facile topotactic ion-exchange with mono, di and trivalent cations. Display Omitted - Highlights: • Ten AInM′S{sub 4} compounds with diverse structure types were synthesized. • They are wide band gap semiconductors. • NaInSnS{sub 4} and KInSnS{sub 4} compounds undergo facile topotactic ion-exchange at room temperature.

Table S1 Basic characteristics of 32 SNPs of neurotransmitter ...

Indian Academy of Sciences (India)

微软用户

Basic characteristics of 32 SNPs in neurotransmitter-related genes. Gene .... rs45435444, rs80837467 and rs80980072, significant differences (P. *** * ... At the same age and environments, skin lesion scores on the ears (P < 0.001), front (P <.

Residual stresses