On Calculation Methods and Results for Straight Cylindrical Roller Bearing Deflection, Stiffness, and Stress

Science.gov (United States)

Krantz, Timothy L.

2011-01-01

The purpose of this study was to assess some calculation methods for quantifying the relationships of bearing geometry, material properties, load, deflection, stiffness, and stress. The scope of the work was limited to two-dimensional modeling of straight cylindrical roller bearings. Preparations for studies of dynamic response of bearings with damaged surfaces motivated this work. Studies were selected to exercise and build confidence in the numerical tools. Three calculation methods were used in this work. Two of the methods were numerical solutions of the Hertz contact approach. The third method used was a combined finite element surface integral method. Example calculations were done for a single roller loaded between an inner and outer raceway for code verification. Next, a bearing with 13 rollers and all-steel construction was used as an example to do additional code verification, including an assessment of the leading order of accuracy of the finite element and surface integral method. Results from that study show that the method is at least first-order accurate. Those results also show that the contact grid refinement has a more significant influence on precision as compared to the finite element grid refinement. To explore the influence of material properties, the 13-roller bearing was modeled as made from Nitinol 60, a material with very different properties from steel and showing some potential for bearing applications. The codes were exercised to compare contact areas and stress levels for steel and Nitinol 60 bearings operating at equivalent power density. As a step toward modeling the dynamic response of bearings having surface damage, static analyses were completed to simulate a bearing with a spall or similar damage.

Roller Bearing Monitoring by New Subspace-Based Damage Indicator

Directory of Open Access Journals (Sweden)

G. Gautier

2015-01-01

Full Text Available A frequency-band subspace-based damage identification method for fault diagnosis in roller bearings is presented. Subspace-based damage indicators are obtained by filtering the vibration data in the frequency range where damage is likely to occur, that is, around the bearing characteristic frequencies. The proposed method is validated by considering simulated data of a damaged bearing. Also, an experimental case is considered which focuses on collecting the vibration data issued from a run-to-failure test. It is shown that the proposed method can detect bearing defects and, as such, it appears to be an efficient tool for diagnosis purpose.

Intelligence diagnosis method for roller bearings using features of AE signal

International Nuclear Information System (INIS)

Pan, J; Wang, H Q; Wang, F; Yang, J F; Liu, W B

2012-01-01

Rolling bearings are important components in rotating machines, which are wildly used in industrial production. The fault diagnosis technology plays a very important role for quality and life of machines. Based on symptom parameters of acoustic emission (AE) signals, this paper presents an intelligent diagnosis method for roller bearings using the principal component analysis, rough sets, and BP neural network to detect faults and distinguish fault types. The principal component analysis and the rough sets algorithm are used to reduce details of time-domain symptom parameters for training the BP neural network. The BP neural network, which is used for condition diagnosis of roller bearings, can obtain good convergence using the symptom parameters acquired by the principal component analysis and the rough sets during learning, and automatically distinguish fault types during diagnosing. Practical examples are provided to verify the efficiency of the proposed method.

A Optimal Dimension Parameters Design of Needle Roller Bearings Considering Multi Factors Affecting Life

Science.gov (United States)

Bai, XiaoBo; Li, Bo

2017-12-01

Taking into many influencing factors, a Needle Roller Bearings life calculation model was established using the Influence coefficient method and ISO formula. Take this model as the optimization objective function, some optimization variables were determined, and these variables were added constraint conditions. Using dynamic nonlinear strategy to improve the inertia weight, the arccosine strategy to adjust the learning factor, function constraints was solved by the methods of ensure particle legitimacy. Nonlinear optimization design of cylindrical roller bearings was realized by Improved Particle Swarm Algorithm. The proposed method of bearing design was verified effective by test of the optimization results.

Compressed sensing of roller bearing fault based on multiple down-sampling strategy

Science.gov (United States)

Wang, Huaqing; Ke, Yanliang; Luo, Ganggang; Tang, Gang

2016-02-01

Roller bearings are essential components of rotating machinery and are often exposed to complex operating conditions, which can easily lead to their failures. Thus, to ensure normal production and the safety of machine operators, it is essential to detect the failures as soon as possible. However, it is a major challenge to maintain a balance between detection efficiency and big data acquisition given the limitations of sampling theory. To overcome these limitations, we try to preserve the information pertaining to roller bearing failures using a sampling rate far below the Nyquist sampling rate, which can ease the pressure generated by the large-scale data. The big data of a faulty roller bearing’s vibration signals is firstly reduced by a down-sample strategy while preserving the fault features by selecting peaks to represent the data segments in time domain. However, a problem arises in that the fault features may be weaker than before, since the noise may be mistaken for the peaks when the noise is stronger than the vibration signals, which makes the fault features unable to be extracted by commonly-used envelope analysis. Here we employ compressive sensing theory to overcome this problem, which can make a signal enhancement and reduce the sample sizes further. Moreover, it is capable of detecting fault features from a small number of samples based on orthogonal matching pursuit approach, which can overcome the shortcomings of the multiple down-sample algorithm. Experimental results validate the effectiveness of the proposed technique in detecting roller bearing faults.

Compressed sensing of roller bearing fault based on multiple down-sampling strategy

International Nuclear Information System (INIS)

Wang, Huaqing; Ke, Yanliang; Luo, Ganggang; Tang, Gang

2016-01-01

Roller bearings are essential components of rotating machinery and are often exposed to complex operating conditions, which can easily lead to their failures. Thus, to ensure normal production and the safety of machine operators, it is essential to detect the failures as soon as possible. However, it is a major challenge to maintain a balance between detection efficiency and big data acquisition given the limitations of sampling theory. To overcome these limitations, we try to preserve the information pertaining to roller bearing failures using a sampling rate far below the Nyquist sampling rate, which can ease the pressure generated by the large-scale data. The big data of a faulty roller bearing’s vibration signals is firstly reduced by a down-sample strategy while preserving the fault features by selecting peaks to represent the data segments in time domain. However, a problem arises in that the fault features may be weaker than before, since the noise may be mistaken for the peaks when the noise is stronger than the vibration signals, which makes the fault features unable to be extracted by commonly-used envelope analysis. Here we employ compressive sensing theory to overcome this problem, which can make a signal enhancement and reduce the sample sizes further. Moreover, it is capable of detecting fault features from a small number of samples based on orthogonal matching pursuit approach, which can overcome the shortcomings of the multiple down-sample algorithm. Experimental results validate the effectiveness of the proposed technique in detecting roller bearing faults. (paper)

Prevention of Roller Bearing-Initiated Burnoffs in Railroad Freight Car Journals

Science.gov (United States)

1979-01-01

The objective of this program was to determine the technical feasibility and cost effectiveness of constructing three separate devices for the prevention of catastrophic roller bearing-initiated, railroad journal failure. 1. Construction of a low cos...

Avoiding Electroerosion in roller bearings; Elektroerosion in Waelzlagern vermeiden

Energy Technology Data Exchange (ETDEWEB)

Preisinger, G.; Groeschl, M. [Inst. fuer Allgemeine Physik der TU Wien (Austria); Koettritsch, H. [SKF Oesterreich AG, Steyr (Austria)

2001-12-17

Roller bearings in electric motors and generators can be exposed to passage of current, which failes not only components, but also changes lubricants. The erosion can be avoided by isolation layers and optimized frequency converters. [German] Waelzlager in Elektromotoren und Generatoren koennen Stromdurchgang ausgesetzt sein, der nicht nur die Teile schaedigt, sondern auch den Schmierstoff veraendert. Die Schaeden sind nicht nur auf Metallteile begrenzt. Abhilfe bieten Isolationsschichten und optimierte Frequenzumrichter. (orig.)

Adaptive Technology Application for Vibration-Based Diagnostics of Roller Bearings on Industrial Plants

Directory of Open Access Journals (Sweden)

Mironov Aleksey

2014-09-01

Full Text Available Roller bearings are widely used in equipment of different applications; therefore, the issues related to the assessment of bearing technical state and localization of bearing faults are quite important and relevant. The reason is that technical state of a bearing is a critical component, which determines efficiency of a mechanism or equipment. For bearings inspection and diagnostics, various methods of vibration-based diagnostics are used. The adaptive technology for vibration-based diagnostics developed in „D un D centrs” is an effective tool for evaluation of technical state of bearings in operation compared to the existing SKF method.

High Capacity cylinder roller bearing; High Capacity Zylinderrollenlager. Ein vollrolliges Lager mit Kaefig

Energy Technology Data Exchange (ETDEWEB)

Reichert, J.; Baum, J. [SKF, Schweinfurt (Germany)

2007-07-15

The high capacity cylinder roller bearing is an example for continuous development of SKF products and does an effective contribution to increase operational safety and offers the possibility to reduce weight and compact design. (GL)

Kinematic correction for roller skewing

Science.gov (United States)

Savage, M.; Loewenthal, S. H.

1980-01-01

A theory of kinematic stabilization of rolling cylinders is developed for high-speed cylindrical roller bearings. This stabilization requires race and roller crowning to product changes in the rolling geometry as the roller shifts axially. These changes put a reverse skew in the rolling elements by changing the rolling taper. Twelve basic possible bearing modifications are identified in this paper. Four have single transverse convex curvature in the rollers while eight have rollers with compound transverse curvature composed of a central cylindrical band of constant radius surrounded by symmetric bands with both slope and transverse curvature.

Compressive Sensing of Roller Bearing Faults via Harmonic Detection from Under-Sampled Vibration Signals.

Science.gov (United States)

Tang, Gang; Hou, Wei; Wang, Huaqing; Luo, Ganggang; Ma, Jianwei

2015-10-09

The Shannon sampling principle requires substantial amounts of data to ensure the accuracy of on-line monitoring of roller bearing fault signals. Challenges are often encountered as a result of the cumbersome data monitoring, thus a novel method focused on compressed vibration signals for detecting roller bearing faults is developed in this study. Considering that harmonics often represent the fault characteristic frequencies in vibration signals, a compressive sensing frame of characteristic harmonics is proposed to detect bearing faults. A compressed vibration signal is first acquired from a sensing matrix with information preserved through a well-designed sampling strategy. A reconstruction process of the under-sampled vibration signal is then pursued as attempts are conducted to detect the characteristic harmonics from sparse measurements through a compressive matching pursuit strategy. In the proposed method bearing fault features depend on the existence of characteristic harmonics, as typically detected directly from compressed data far before reconstruction completion. The process of sampling and detection may then be performed simultaneously without complete recovery of the under-sampled signals. The effectiveness of the proposed method is validated by simulations and experiments.

78 FR 40692 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

Science.gov (United States)

2013-07-08

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-601] Tapered Roller Bearings and..., International Trade Administration, Department of Commerce. SUMMARY: The Department of Commerce (Department) is... Department selected one mandatory respondent for individual examination (i.e., Changshan Peer Bearing Co. Ltd...

Research In Diagnosing Bearing Defects From Vibrations

Science.gov (United States)

Zoladz, T.; Earhart, E.; Fiorucci, T.

1995-01-01

Report describes research in bearing-defect signature analysis - use of vibration-signal analysis to diagnose defects in roller and ball bearings. Experiments performed on bearings in good condition and other bearings in which various parts scratched to provide known defects correlated with vibration signals. Experiments performed on highly instrumented motor-driven rotor assembly at speeds up to 10,050 r/min, using accelerometers, velocity probes, and proximity sensors mounted at various locations on assembly to measure vibrations.

Bearing life in contaminated oil and oil passing into bearing for tapered roller bearing; Ensui koro jikuuke ni okeru ibutsu yuchu deno jumyo to kantsu yuryo

Energy Technology Data Exchange (ETDEWEB)

Asai, Y; Oshima, H; Sakamoto, K [Koyo Seiko Co. Ltd., Osaka (Japan)

1997-10-01

In this paper a relationship between depth of dents, area of dents gathered and bearing life has been investigated for tapered roller bearings used in differential gear case. It is effective for the longer bearing life to reduce hard particles of Fe especially among several contaminations existing in the gear case. It is also effective to make oil level lower in the case from the view point for reduction of number of dents. 8 refs., 8 figs., 4 tabs.

Mechanical analysis and optimisation of large and highly-loaded bearing rollers For the "Riesenrad" Ion Gantry

CERN Document Server

Reimoser, S A

2000-01-01

A carbon ion gantry would allow the irradiation of cancer patients with carbon ions from any direction in space best suited for therapy. Till today, such a machine has not been built due to the expected size, mass and cost. A novel design, called "Riesenrad" ion gantry, promises to provide a competitive solution. The central part of the Riesenrad, which can rotate ± 90°, is supported (statically determinate) on pendular bearing units with two rollers each. High precision requirements for the structure rule out any plastic deformations in the area of contact. The present report describes the design of the highly-loaded rollers. In order to achieve a large contact area and a uniform distribution of contact stresses, a "barrel shape" for the rollers is proposed. An analysis using the finite element method (FEM) was performed to optimise the roller design, namely to establish the required crown roll (camber radius).

A Sparsity-Promoted Decomposition for Compressed Fault Diagnosis of Roller Bearings

Directory of Open Access Journals (Sweden)

Huaqing Wang

2016-09-01

Full Text Available The traditional approaches for condition monitoring of roller bearings are almost always achieved under Shannon sampling theorem conditions, leading to a big-data problem. The compressed sensing (CS theory provides a new solution to the big-data problem. However, the vibration signals are insufficiently sparse and it is difficult to achieve sparsity using the conventional techniques, which impedes the application of CS theory. Therefore, it is of great significance to promote the sparsity when applying the CS theory to fault diagnosis of roller bearings. To increase the sparsity of vibration signals, a sparsity-promoted method called the tunable Q-factor wavelet transform based on decomposing the analyzed signals into transient impact components and high oscillation components is utilized in this work. The former become sparser than the raw signals with noise eliminated, whereas the latter include noise. Thus, the decomposed transient impact components replace the original signals for analysis. The CS theory is applied to extract the fault features without complete reconstruction, which means that the reconstruction can be completed when the components with interested frequencies are detected and the fault diagnosis can be achieved during the reconstruction procedure. The application cases prove that the CS theory assisted by the tunable Q-factor wavelet transform can successfully extract the fault features from the compressed samples.

Vibration analysis of paper machine's asymmetric tube roll supported by spherical roller bearings

Science.gov (United States)

Heikkinen, Janne E.; Ghalamchi, Behnam; Viitala, Raine; Sopanen, Jussi; Juhanko, Jari; Mikkola, Aki; Kuosmanen, Petri

2018-05-01

This paper presents a simulation method that is used to study subcritical vibrations of a tube roll in a paper machine. This study employs asymmetric 3D beam elements based on the Timoshenko beam theory. An asymmetric beam model accounts for varying stiffness and mass distributions. Additionally, a detailed rolling element bearing model defines the excitations arising from the set of spherical roller bearings at both ends of the rotor. The results obtained from the simulation model are compared against the results from the measurements. The results indicate that the waviness of the bearing rolling surfaces contributes significantly to the subcritical vibrations while the asymmetric properties of the tube roll have only a fractional effect on the studied vibrations.

Chaotic Dynamics of Cage Behavior in a High-Speed Cylindrical Roller Bearing

Directory of Open Access Journals (Sweden)

Long Chen

2016-01-01

Full Text Available This paper presents a mathematical model to investigate the nonlinear dynamic behavior of cage in high-speed cylindrical bearing. Variations of cage behavior due to varying cage eccentricity and cage guidance gap are observed. Hydrodynamic behavior in cage contacts is taken into consideration for a more realistic calculation of acting forces owing to high working speed. Analysis of real-time cage dynamic behavior on radial plane is carried out using chaos theory based on the theoretical and mathematical model established in the paper. The analytical results of this paper provide a solid foundation for designing and manufacturing of high-speed cylindrical roller bearing.

Bearing assemblies, apparatuses, and motor assemblies using the same

Science.gov (United States)

Sexton, Timothy N.; Cooley, Craig H.; Knuteson, Cody W.

2015-12-29

Various embodiments of the invention relate to bearing assemblies, apparatuses and motor assemblies that include geometric features configured to impart a selected amount of heat transfer and/or hydrodynamic film formation. In an embodiment, a bearing assembly may include a plurality of superhard bearing pads distributed circumferentially about an axis. At least some of the plurality of superhard bearing pads may include a plurality of sub-superhard bearing elements defining a bearing surface. At least some of the plurality of sub-superhard bearing elements may be spaced from one another by one or more voids to impart a selected amount of heat transfer and hydrodynamic film formation thereon during operation. The bearing assembly may also include a support ring that carries the plurality of superhard bearing pads. In addition, at least a portion of the sub-superhard bearing elements may extend beyond the support ring.

78 FR 45912 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

Science.gov (United States)

2013-07-30

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-601] Tapered Roller Bearings and..., International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue NW... Duty New Shipper Review AGENCY: Import Administration, International Trade Administration, Department...

Design algorithm for generatrix profile of cylindrical crowned rollers

Directory of Open Access Journals (Sweden)

Creţu Spiridon

2017-01-01

Full Text Available The cross-section of roller profile controls the pressure distribution in the contact area and radically affects the roller bearings basic dynamic load rating and rating lives. Today the most used roller profiles are the logarithmic profile and cylindrical-crowned (ZB profile. The logarithmic profile has a continuous evolution with no discontinuities till the intersection with the end fillet while ZB profile has two more discontinuities at the intersections points between the crowning circle and straight line generatrix. Using a semianalytical method, a numerical study has been carried out to find the optimum ZB profile for rollers incorporated in cylindrical rollers bearings. The basic reference rating life (L10_r has been used as optimization criterion.

77 FR 2031 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished From the People's Republic of...

Science.gov (United States)

2012-01-13

... Parts Thereof, Finished and Unfinished From the People's Republic of China: Extension of the Time Limit..., International Trade Administration, U.S. Department of Commerce, 14th Street and Constitution Avenue NW..., finished and unfinished from the People's Republic of China. See Tapered Roller Bearings and Parts Thereof...

76 FR 76143 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

Science.gov (United States)

2011-12-06

..., the United Steel, Paper and Forestry, Rubber, Manufacturing, Energy, Allied Industrial and Service... manufacturing of tapered roller bearings and parts thereof in the United States, also notified the Department... manufacturing the domestic like product, and therefore, is an interested party pursuant to section 771(9)(D) of...

Application of Dang Van criterion to rolling contact fatigue in wind turbine roller bearings under elastohydrodynamic lubrication conditions

DEFF Research Database (Denmark)

Cerullo, Michele

2014-01-01

classic Hertzian and elastohydrodynamic lubrication theories have been used to model the pressure distribution acting on the inner raceway and results are compared according to the Dang Van multiaxial fatigue criterion. The contact on the bearing raceway is simulated by substituting the roller...

Workload analyse of assembling process

Science.gov (United States)

Ghenghea, L. D.

2015-11-01

The workload is the most important indicator for managers responsible of industrial technological processes no matter if these are automated, mechanized or simply manual in each case, machines or workers will be in the focus of workload measurements. The paper deals with workload analyses made to a most part manual assembling technology for roller bearings assembling process, executed in a big company, with integrated bearings manufacturing processes. In this analyses the delay sample technique have been used to identify and divide all bearing assemblers activities, to get information about time parts from 480 minutes day work time that workers allow to each activity. The developed study shows some ways to increase the process productivity without supplementary investments and also indicated the process automation could be the solution to gain maximum productivity.

Degradation Assessment and Fault Diagnosis for Roller Bearing Based on AR Model and Fuzzy Cluster Analysis

Directory of Open Access Journals (Sweden)

Lingli Jiang

2011-01-01

Full Text Available This paper proposes a new approach combining autoregressive (AR model and fuzzy cluster analysis for bearing fault diagnosis and degradation assessment. AR model is an effective approach to extract the fault feature, and is generally applied to stationary signals. However, the fault vibration signals of a roller bearing are non-stationary and non-Gaussian. Aiming at this problem, the set of parameters of the AR model is estimated based on higher-order cumulants. Consequently, the AR parameters are taken as the feature vectors, and fuzzy cluster analysis is applied to perform classification and pattern recognition. Experiments analysis results show that the proposed method can be used to identify various types and severities of fault bearings. This study is significant for non-stationary and non-Gaussian signal analysis, fault diagnosis and degradation assessment.

Micromechanical study of the effect of inclusions on fatigue failure in a roller bearing

DEFF Research Database (Denmark)

Cerullo, Michele; Tvergaard, Viggo

2015-01-01

model containing a single inclusion, using the approximation of a 2D plane strain numerical analysis. The Dang Van multiaxial fatigue criterion is used for the local stresses in the matrix material, to ensure that the stresses remain within the fatigue limit. The matrix material is taken to be one...... of the most commonly used bearing steels, AISI 52100, and two different types of inclusions are considered. The macroscopic stress histories applied correspond to either a Hertzian or an elastohydrodynamic (EHL) contact pressure distribution under the rollers. Findings - The paper shows that sub...

Bearing construction for refrigeration compresssor

Science.gov (United States)

Middleton, Marc G.; Nelson, Richard T.

1988-01-01

A hermetic refrigeration compressor has a cylinder block and a crankshaft rotatable about a vertical axis to reciprocate a piston in a cylinder on the cylinder block. A separate bearing housing is secured to the central portion of the cylinder block and extends vertically along the crankshaft, where it carries a pair of roller bearings to journal the crankshaft. The crankshaft has a radially extending flange which is journaled by a thrust-type roller bearing above the bearing housing to absorb the vertical forces on the crankshaft so that all three of the roller bearings are between the crankshaft and the bearing housing to maintain and control the close tolerances required by such bearings.

Partial tooth gear bearings

Science.gov (United States)

Vranish, John M. (Inventor)

2010-01-01

A partial gear bearing including an upper half, comprising peak partial teeth, and a lower, or bottom, half, comprising valley partial teeth. The upper half also has an integrated roller section between each of the peak partial teeth with a radius equal to the gear pitch radius of the radially outwardly extending peak partial teeth. Conversely, the lower half has an integrated roller section between each of the valley half teeth with a radius also equal to the gear pitch radius of the peak partial teeth. The valley partial teeth extend radially inwardly from its roller section. The peak and valley partial teeth are exactly out of phase with each other, as are the roller sections of the upper and lower halves. Essentially, the end roller bearing of the typical gear bearing has been integrated into the normal gear tooth pattern.

Development of an aerostatic bearing system for roll-to-roll printed electronics

Science.gov (United States)

Chen, Shasha; Chen, Weihai; Liu, Jingmeng; Chen, Wenjie; Jin, Yan

2018-06-01

Roll-to-roll printed electronics is proved to be an effective way to fabricate electrical devices on various substrates. High precision overlay alignment plays a key role to create multi-layer electrical devices. Multiple rollers are adopted to support and transport the substrate web. In order to eliminate the negative effect of the machining error and assembling error of the roller, a whole roll-to-roll system including two aerostatic bearing devices with arrayed restrictors is proposed in this paper. Different to the conventional roller, the aerostatic bearing device can create a layer of air film between the web and the device to realize non-contact support and transport. Based on simplified Navier–Stokes equations, the theoretical model of the air film is established. Moreover, the pressure distribution of the whole flow field and single restrictor in different positions are modeled by conducting numerical simulation with computational fluid dynamics (CFD) software FLUENT. The load capacity curves and stiffness curves are generated to provide guidance for optimizing the structure of the device. A prototype of the aerostatic bearing system is set up and the experiment tests are carried out. For the proposed aerostatic bearing roller with a diameter of 100 mm and length of 200 mm, the experimental results show the aerostatic bearing method can achieve the position accuracy in a range of 1 μm in the vertical direction of the web, which is much better than that using existing methods.

A hybrid approach to fault diagnosis of roller bearings under variable speed conditions

Science.gov (United States)

Wang, Yanxue; Yang, Lin; Xiang, Jiawei; Yang, Jianwei; He, Shuilong

2017-12-01

Rolling element bearings are one of the main elements in rotating machines, whose failure may lead to a fatal breakdown and significant economic losses. Conventional vibration-based diagnostic methods are based on the stationary assumption, thus they are not applicable to the diagnosis of bearings working under varying speeds. This constraint limits the bearing diagnosis to the industrial application significantly. A hybrid approach to fault diagnosis of roller bearings under variable speed conditions is proposed in this work, based on computed order tracking (COT) and variational mode decomposition (VMD)-based time frequency representation (VTFR). COT is utilized to resample the non-stationary vibration signal in the angular domain, while VMD is used to decompose the resampled signal into a number of band-limited intrinsic mode functions (BLIMFs). A VTFR is then constructed based on the estimated instantaneous frequency and instantaneous amplitude of each BLIMF. Moreover, the Gini index and time-frequency kurtosis are both proposed to quantitatively measure the sparsity and concentration measurement of time-frequency representation, respectively. The effectiveness of the VTFR for extracting nonlinear components has been verified by a bat signal. Results of this numerical simulation also show the sparsity and concentration of the VTFR are better than those of short-time Fourier transform, continuous wavelet transform, Hilbert-Huang transform and Wigner-Ville distribution techniques. Several experimental results have further demonstrated that the proposed method can well detect bearing faults under variable speed conditions.

Impact Analysis of Roller System Stability for Four-High Mill Horizontal Vibration

Directory of Open Access Journals (Sweden)

Xiao-bin Fan

2016-01-01

Full Text Available In order to study the hot Compact Strip Production (CSP, four-high mill vibration characteristics, and vibration suppression method, the roller system structure stability was analyzed and calculated at first in the paper. And then, the mill stand gap was measured at field and its influence on roll transverse vibration was analyzed. The drum gear coupling effect on the roller system stability and the automatic balance conditions of the coupling transmission torque were studied; the influence of axial force caused by the roller cross on the system stability was analyzed. Finally, the roller transverse friction chatter vibration mechanics model was established; the simulation analysis was carried out with eliminating mill house-bearing clearance and adding floating support for coupling, respectively. And the characteristics of the roller “jump vibration” were studied. We applied copper gaskets to eliminate or reduce mill house-bearing clearance for suppressing the rolling mill vibration on the spot; the test results show that the roller transverse vibration was suppressed after eliminating clearance.

77 FR 50716 - Tapered Roller Bearings From China

Science.gov (United States)

2012-08-22

... INTERNATIONAL TRADE COMMISSION [Investigation No. 731-TA-344 (Third Review)] Tapered Roller..., the United States International Trade Commission (Commission) determines, pursuant to section 751(c... notice in the Office of the Secretary, U.S. International Trade Commission, Washington, DC, and by...

Gearbox Reliability Collaborative Gearbox 3 Planet Bearing Calibration

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-03-24

The Gearbox Reliability Collaborative gearbox was redesigned to improve its load-sharing characteristics and predicted fatigue life. The most important aspect of the redesign was to replace the cylindrical roller bearings with preloaded tapered roller bearings in the planetary section. Similar to previous work, the strain gages installed on the planet tapered roller bearings were calibrated in a load frame. This report describes the calibration tests and provides the factors necessary to convert the measured units from dynamometer testing to bearing loads, suitable for comparison to engineering models.

Valve assembly having remotely replaceable bearings

International Nuclear Information System (INIS)

Johnson, E.R.; Tanner, D.E.

1980-01-01

A valve assembly having remotely replaceable bearings is disclosed wherein a valve disc is supported within a flow duct for rotation about a pair of axially aligned bearings, one of which is carried by a spindle received within a diametral bore in the valve disc, and the other of which is carried by a bearing support block releasably mounted on the duct circumferentially of an annular collar on the valve disc coaxial with its diametrical bore. The spindle and bearing support block are adapted for remote removal to facilitate servicing or replacement of the valve disc support bearings

Documentation of roller-bearing effect on butterfly inspired grooves

Science.gov (United States)

Gautam, Sashank; Lang, Amy

2017-11-01

Butterfly wings are covered with scales in a roof shingle pattern which align together to form grooves. The increase or decrease of laminar friction drag depends on the flow orientation to the scales. Flow in the longitudinal direction to the grooves encounters increased surface area which increases the friction drag. However, in the transverse direction, for low Re laminar flow, a single vortex is formed inside each groove and is predicted to remain stable due to the very low Re of the flow in each cavity. These embedded vortices act as roller bearings to the flow above, such that the fluid from the outer boundary layer does not mix with fluid inside the cavities. This leads to a reduction of skin friction drag when compared to a smooth surface. When the cavity flow Re is increased beyond a critical point, the vortex becomes unstable and the low-momentum fluid in the grooves mixes with the outer boundary layer flow, increasing the drag. The objective of this experiment is to determine the critical Re where the embedded vortex transitions from a stable to an unstable state using DPIV. Subsequently, for steady vortex conditions, a comparison of skin friction drag between the grooved and flat plate can show that the butterfly scaled surface can result in sub-laminar friction drag. The National Science Foundation (Grant No. 1335848).

Transient Vibration Prediction for Rotors on Ball Bearings Using Load-dependent Non-linear Bearing Stiffness

Science.gov (United States)

Fleming, David P.; Poplawski, J. V.

2002-01-01

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic transient analysis requires bearing forces to be determined at each step of the transient solution. Analyses have been carried out to show the effect of accurate bearing transient forces (accounting for non-linear speed and load dependent bearing stiffness) as compared to conventional use of average rolling-element bearing stiffness. Bearing forces were calculated by COBRA-AHS (Computer Optimized Ball and Roller Bearing Analysis - Advanced High Speed) and supplied to the rotordynamics code ARDS (Analysis of Rotor Dynamic Systems) for accurate simulation of rotor transient behavior. COBRA-AHS is a fast-running 5 degree-of-freedom computer code able to calculate high speed rolling-element bearing load-displacement data for radial and angular contact ball bearings and also for cylindrical and tapered roller beatings. Results show that use of nonlinear bearing characteristics is essential for accurate prediction of rotordynamic behavior.

Load beam unit replaceable inserts for dry coal extrusion pumps

Science.gov (United States)

Saunders, Timothy; Brady, John D.

2012-11-13

A track assembly for a particulate material extrusion pump according to an exemplary aspect of the present disclosure includes a link assembly with a roller bearing. An insert mounted to a load beam located such that the roller bearing contacts the insert.

Analysis of bearing steel exposed to rolling contact fatigue

DEFF Research Database (Denmark)

Hansen, K. T.; Fæster, Søren; Natarajan, Anand

2017-01-01

The objective of this work is to characterize fatigue damage in roller bearings under conditions of high load and slippage. A test rig constructed for rolling contact fatigue tests of rings is described, and test results are presented for rings taken from two spherical roller bearings. The prepar...

Screw-released roller brake

Science.gov (United States)

Vranish, John M. (Inventor)

1999-01-01

A screw-released roller brake including an input drive assembly, an output drive assembly, a plurality of locking sprags, a mechanical tripper nut for unlocking the sprags, and a casing therefor. The sprags consist of three dimensional (3-D) sprag members having pairs of contact surface regions which engage respective pairs of contact surface regions included in angular grooves or slots formed in the casing and the output drive assembly. The sprags operate to lock the output drive assembly to the casing to prevent rotation thereof in an idle mode of operation. In a drive mode of operation, the tripper is either self actuated or motor driven and is translated linearly up and down against a spline and at the limit of its travel rotates the sprags which unlock while coupling the input drive assembly to the output drive assembly so as to impart a turning motion thereto in either a clockwise or counterclockwise direction.

Determination of the contact stresses in double-row tapered roller bearings using the finite element method, experimental analysis and analytical models

Energy Technology Data Exchange (ETDEWEB)

Lostado, Ruben [University of La Rioja, Logroño (Spain); Martinez, Roberto Fernandez [University of Basque Country UPV/EHU, Bilbao (Spain); MacDonald, Bryan J. [Dublin City University, Dublin (Ireland)

2015-11-15

Double-row Tapered roller bearings (TRBs) are mechanical devices that are designed to support high axial, radial and torque loads. This combination of loads produces high contact stresses on the bearing raceways that are difficult to predict and validate experimentally, and can cause defects like pitting and fatigue spalling. In response, theoretical models have been proposed by many researchers to calculate the approximate distribution of contact stresses over the bearing raceways. More recently, numerical methods that are based on the Finite element method (FEM) have been used to obtain the contact stresses, although this method requires that the mesh size first be adjusted. This paper shows a process for adjusting a double-row TRB Finite element (FE) model. It is based on generating successive nonlinear FE submodels to calculate the distribution of contact stresses. A theoretical model and contact pressure sensors were used to adjust and validate the Finite element (FE) model.

Self-lubricating fluid bearing assembly

International Nuclear Information System (INIS)

Kapich, D.D.

1981-01-01

A sealed self-lubricating fluid bearing assembly is described for circulating fluid in the form of a gas coolant in a nuclear reactor, the power for the circulator being provided by a shaft located within the primary containment vessel. In such a system the reactor coolant is isolated from the fluid region at the far end of the drive shaft. (U.K.)

INFLUENCE CONSTRUCTION OF THE ROLLER ON THE POWER OF THE DRIVE SYSTEM OF THE BELT CONVEYOR

Directory of Open Access Journals (Sweden)

Tadeusz OPASIAK

2014-09-01

Full Text Available The paper presents a study of new design of rollers. The study focused on the measurement of static and dynamic resistance of rotating rollers and the impact of new construction on the power consumption of the belt conveyor. Rollers have been modified through the use of class C4 bearing seals and labyrinth seal U4Exp 62/65 with a cover 2LU4 of runner construction. Measurements of static and dynamic resistance of rotating rollers were made on a universal rollers stand and power measurements were carried out on a belt conveyor power supply system Gwarek 1200 No. TW in mine KWK Mysłowice–Wesoła.

Rolling Bearing Life Prediction, Theory, and Application

Science.gov (United States)

Zaretsky, Erwin V.

2016-01-01

A tutorial is presented outlining the evolution, theory, and application of rolling-element bearing life prediction from that of A. Palmgren, 1924; W. Weibull, 1939; G. Lundberg and A. Palmgren, 1947 and 1952; E. Ioannides and T. Harris, 1985; and E. Zaretsky, 1987. Comparisons are made between these life models. The Ioannides-Harris model without a fatigue limit is identical to the Lundberg-Palmgren model. The Weibull model is similar to that of Zaretsky if the exponents are chosen to be identical. Both the load-life and Hertz stress-life relations of Weibull, Lundberg and Palmgren, and Ioannides and Harris reflect a strong dependence on the Weibull slope. The Zaretsky model decouples the dependence of the critical shear stress-life relation from the Weibull slope. This results in a nominal variation of the Hertz stress-life exponent. For 9th- and 8th-power Hertz stress-life exponents for ball and roller bearings, respectively, the Lundberg-Palmgren model best predicts life. However, for 12th- and 10th-power relations reflected by modern bearing steels, the Zaretsky model based on the Weibull equation is superior. Under the range of stresses examined, the use of a fatigue limit would suggest that (for most operating conditions under which a rolling-element bearing will operate) the bearing will not fail from classical rolling-element fatigue. Realistically, this is not the case. The use of a fatigue limit will significantly overpredict life over a range of normal operating Hertz stresses. (The use of ISO 281:2007 with a fatigue limit in these calculations would result in a bearing life approaching infinity.) Since the predicted lives of rolling-element bearings are high, the problem can become one of undersizing a bearing for a particular application. Rules had been developed to distinguish and compare predicted lives with those actually obtained. Based upon field and test results of 51 ball and roller bearing sets, 98 percent of these bearing sets had acceptable

ANALYSIS OF MOVEMENT RESISTANCE OF CONVEYOR BELT AND ROLLERS IN THE COAL MINE MYSŁOWICE-WESOŁA

Directory of Open Access Journals (Sweden)

Tadeusz OPASIAK

2014-03-01

Full Text Available The paper presents a study of new design of SAG rollers. The study focused on the measurement of static and dynamic resistance of rotating rollers and the impact of new construction on the power consumption of the conveyor. Rollers have been modified through the use of class C4 bearing seals and labyrinth seal U4Exp 62/65 with a cover 2LU4 of runner construction. Measurements of static and dynamic resistance of rotating rollers were made on a universal rollers test bench, and power measurements were carried out on a belt conveyor power supply system Gwarek 1200 No. TW in KWK Mysłowice-Wesoła

Load-bearing processes in agricultural wheel-soil systems

NARCIS (Netherlands)

Tijink, F.G.J.

1988-01-01

In soil dynamics we distinguish between loosening and loadbearing processes. Load-bearing processes which can occur under agricultural rollers, wheels, and tyres are dealt with In this dissertation.

We classify rollers, wheels, and tyres and treat some general aspects of these

System and method for conveying an assembly

KAUST Repository

Eitelhuber, Georg

2015-01-01

angles. A carriage assembly can include a drive wheel and at least two roller sets. The drive wheel can be configured to contact the first planar side and is configured to translate the carriage assembly along the rail. The at least two roller sets can

Modelling of a mecanum wheel taking into account the geometry of road rollers

Science.gov (United States)

Hryniewicz, P.; Gwiazda, A.; Banaś, W.; Sękala, A.; Foit, K.

2017-08-01

the road rollers, is their bearings. Depending on the load, carried by the vehicle and the rotational speed of the drive wheel, the bearings themselves can greatly affect the diameter of the rollers and the whole Mecanum wheels. The solution of this problem is presented in the paper. It is illustrated with virtual models elaborated in advanced program of the CAE class.

Use of high frequency analysis of acoustic emission signals to determine rolling element bearing condition

International Nuclear Information System (INIS)

Cockerill, A; Holford, K M; Pullin, R; Clarke, A; Bradshaw, T; Cole, P

2015-01-01

Acoustic Emission (AE) sensors were used to detect signals arising from a cylindrical roller bearing with artificial defects seeded onto the outer raceway. An SKF N204ECP roller bearing was placed between two double row spherical roller bearings, type SKF 22202E, and loaded between 0.29 and 1.79kN. Speed was constant at 5780rpm. High frequency analysis allowed insight into the condition of the bearings through the determination of an increase in the structural resonances of the system as the size of an artificial defect was increased. As higher loads were applied, frequencies around 100kHz were excited, indicating the release of AE possibly attributed to friction and the plastic deformation as peaks, induced through engraving of the raceway, were flattened and worn down. Sensitivity of AE to this level in bearings indicates the potential of the technique to detect the early stages of bearing failure during life tests. (paper)

Sequential Fuzzy Diagnosis Method for Motor Roller Bearing in Variable Operating Conditions Based on Vibration Analysis

Directory of Open Access Journals (Sweden)

Yi Cao

2013-06-01

Full Text Available A novel intelligent fault diagnosis method for motor roller bearings which operate under unsteady rotating speed and load is proposed in this paper. The pseudo Wigner-Ville distribution (PWVD and the relative crossing information (RCI methods are used for extracting the feature spectra from the non-stationary vibration signal measured for condition diagnosis. The RCI is used to automatically extract the feature spectrum from the time-frequency distribution of the vibration signal. The extracted feature spectrum is instantaneous, and not correlated with the rotation speed and load. By using the ant colony optimization (ACO clustering algorithm, the synthesizing symptom parameters (SSP for condition diagnosis are obtained. The experimental results shows that the diagnostic sensitivity of the SSP is higher than original symptom parameter (SP, and the SSP can sensitively reflect the characteristics of the feature spectrum for precise condition diagnosis. Finally, a fuzzy diagnosis method based on sequential inference and possibility theory is also proposed, by which the conditions of the machine can be identified sequentially as well.

Evaluation of ball and roller bearings restored by grinding

Science.gov (United States)

Parker, R. J.; Zaretsky, E. V.; Chen, S. M.

1976-01-01

A joint program was undertaken to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. Groups of each of these bearings were visually and dimensionally inspected for suitability for restoration. A total of 250 bearings were restored by grinding. Of this number, 30 bearings from each type were endurance tested to a TBO of 1600 hours. No bearing failures occurred related to the restoration by grinding process. The two bearing failures which occurred were due to defective rolling elements and were typical of those which may occur in new bearings. The restorable component yield to the three groups was in excess of 90 percent.

Profiled Roller Stress/Fatigue Life Analysis Methodology and Establishment of an Appropriate Stress/Life Exponent

Science.gov (United States)

1997-01-01

The objective of this work was to determine the three dimensional volumetric stress field, surface pressure distribution and actual contact area between a 0.50" square roller with different crown profiles and a flat raceway surface using Finite Element Analysis. The 3-dimensional stress field data was used in conjunction with several bearing fatigue life theories to extract appropriate values for stress-life exponents. Also, results of the FEA runs were used to evaluate the laminated roller model presently used for stress and life prediction.

RELATIONSHIP BETWEEN ROLLING AND SLIP RESISTANCE IN ROLLING BEARINGS

Directory of Open Access Journals (Sweden)

L. M. Bondarenko

2016-06-01

Full Text Available Purpose. About one of the causes of slip rolling is known from the second half of the 19th century, it was believed that the slip resistance appears at the place of contact due to different speeds on the arc of contact. Only in the mid-20th century it was proved that this resistance is negligible in rolling resistance. However (for some unknown reason it is ignored the fact that in practice in rolling bearings may rotate both the inner ring with a stationary outer one, and vice versa almost in equal relations. It is not taken into account the fact that the ball or roller in the rolling bearings runs the different distance along the roller path of the outer and inner bearing cages in one revolution. This fact is not taken into account in determining the calculated values for the friction coefficient of a rolling bearing reduced to the shaft. Therefore, the aim of this work is to determine the influence of path length on the track riding the outer and inner race of the bearing on the determination of the calculated value of the coefficient of friction of rolling bearings is given to the shaft. Methodology. The solution technique is based on the theory of plane motion of a rigid body, the theory of Hertzian contact deformation and the analytical dependencies for determination of coefficient of rolling friction. Findings. The obtained dependences on determination of rolling resistance of the balls or rollers along the bearing tracks of inner and outer bearing cages as well as path difference metering of the rolling on them allows to analytically obtain the rolling resistance and slipping for any size of bearings and different devices of bearing units. It is also possible at the design stage of rolling nodes to handle not only the design but also the content of the node. Originality. Using the analytical dependences for determination of the rolling resistance of bodies at point and line contacts, and also account for the difference in the path of the

Tribology of a Combined Yaw Bearing and Brake for Wind Turbines

DEFF Research Database (Denmark)

Poulios, Konstantinos

disc brake is typically included as an independent system. However, the increasing size of wind turbines makes roller element bearings an economically costly option. Moreover, the additional brake system increases complexity and consequently adds further production and maintenance costs. One...... of the innovations aiming at reducing complexity in the yaw system consists in combining a segmented sliding bearing and a brake into a single system. This thesis studies the tribological implications of such a hybrid sliding bearing and brake for the yaw system of wind turbines. Based to a large extent...... that are affected by the tendency for building larger units, is the yaw system of horizontal axis wind turbines. State of the art wind turbine yaw systems consist of either a large roller element bearing or a corresponding segmented sliding bearing that connects the wind turbine nacelle and tower. An additional...

Grease lubrication in rolling bearings

CERN Document Server

Lugt, Piet M

2012-01-01

The definitive book on the science of grease lubrication for roller and needle bearings in industrial and vehicle engineering. Grease Lubrication in Rolling Bearings provides an overview of the existing knowledge on the various aspects of grease lubrication (including lubrication systems) and the state of the art models that exist today. The book reviews the physical and chemical aspects of grease lubrication, primarily directed towards lubrication of rolling bearings. The first part of the book covers grease composition, properties and rheology, including thermal

Kinematics of Planetary Roller Screw Mechanism considering Helical Directions of Screw and Roller Threads

Directory of Open Access Journals (Sweden)

Shangjun Ma

2015-01-01

Full Text Available Based on the differential principle of thread transmission, an analytical model considering helical directions between screw and roller threads in planetary roller screw mechanism (PRSM is presented in this work. The model is critical for the design of PRSM with a smaller lead and a bigger pitch to realize a higher transmission accuracy. The kinematic principle of planetary transmission is employed to analyze the PRSM with different screw thread and roller thread directions. In order to investigate the differences with different screw thread and roller thread directions, the numerical model is developed by using the software Adams to validate the analytical solutions calculated by the presented model. The results indicate, when the helical direction of screw thread is identical with the direction of roller thread, that the lead of PRSM is unaffected regardless of whether sliding between screw and rollers occurs or not. Only when the direction of screw thread is reverse to the direction of roller thread, the design of PRSM with a smaller lead can be realized under a bigger pitch. The presented models and numerical simulation method can be used to research the transmission accuracy of PRSM.

General Case in Determining Center-To-Center Spacing Between the Screw and the Roller in a Roller Drive, and Initial Contact Point of Their Mating Thread Turns. Development of Calculation Method and Software

Directory of Open Access Journals (Sweden)

D. S. Blinov

2017-01-01

Full Text Available One of the most important trends in development of machine engineering is to improve load capacity of mechanisms, assemblies and parts without increasing their overall dimensions and weight. This is also relevant to the most promising items so far, i.e. orbital roller drives (ORD, which are the rotational-to-progressive motion converters widely used in vehicles. The previously published article suggested increasing a load capacity (by about 15% through reducing a thread turn section angle of the threaded ORD components and change of the radius of roller thread turn section outline. Due to such ORD modification, a number of the most critical ORD parameters are to be changed thereby demanding further research. Further, the article published suggests a method considering the abovementioned changes to calculate the dimensions of ORD main components and their tolerance ranges.Though this method being not complete as the increment of ORD center-to-center spacing in relation to its rated value, required for assembly, is unknown; and to determine the ORD center-to-center spacing increment, outer diameters of the roller and screw threads are to be known. Hence, these two methods are interconnected.This article presents the numerical calculation method, mathematical support and method to determine the increment of ORD center-to-center spacing and initial contact point of the mating roller and screw thread turns. Due to considerable scope of calculations, the method was turned into the software.Similar calculation methods and techniques were developed to a particular case, where the thread turn section angle of the threaded components was of 90°, and the roller thread turn section outline was a circular arc centered to the roller axis. Hence the developed numerical calculation method, mathematical support and technique refer to the general case which is to determine the ORD center-to-center spacing increment and initial contact point of the mating roller

Self-Mobilization Using a Foam Roller Versus a Roller Massager: Which Is More Effective for Increasing Hamstrings Flexibility?

Science.gov (United States)

DeBruyne, Danielle M; Dewhurst, Marina M; Fischer, Katelyn M; Wojtanowski, Michael S; Durall, Chris

2017-01-01

Clinical Scenario: Increasing the length of the muscle-tendon unit may prevent musculotendinous injury. Various methods have been proposed to increase muscle-tendon flexibility, including self-mobilization using foam rollers or roller massagers, although the effectiveness of these devices is uncertain. This review was conducted to determine if the use of foam rollers or roller massagers to improve hamstrings flexibility is supported by moderate- to high-quality evidence. Are foam rollers or roller massagers effective for increasing hamstrings flexibility in asymptomatic physically active adults? Summary of Key Findings: The literature was searched for studies on the effects of using foam rollers or roller massagers to increase hamstrings flexibility in asymptomatic physically active adults. Four randomized controlled trials were included; 2 studies provided level 2 or 3 evidence regarding foam rollers and 2 studies provided level 2 or 3 evidence regarding roller massagers. Both roller-massager studies reported increases in hamstrings flexibility after treatment. Data from the foam-roller studies did not demonstrate a statistically significant increase in hamstrings flexibility, but 1 study did demonstrate a strong effect size. Clinical Bottom Line: The reviewed moderate-quality studies support the use of roller massagers but provide limited evidence on the effectiveness of foam rolling to increase hamstrings flexibility in asymptomatic physically active adults. Flexibility gains may be improved by a longer duration of treatment and administration by a trained therapist. Gains appear to decline rapidly postrolling. Neither device has been shown to confer a therapeutic benefit superior to static stretching, and the effectiveness of these devices for preventing injury is unknown. Strength of Recommendation: Grade B evidence supports the use of roller massagers to increase hamstrings flexibility in asymptomatic physically active adults.

Radial power distribution shaping within a PWR fuel assembly utilizing asymmetrically loaded gadolinia-bearing fuel pins

International Nuclear Information System (INIS)

Stone, I.Z.

1992-01-01

As in-core fuel management designs evolve to meet the demands of increasing energy output, more innovative methods are developed to maintain power peaking within acceptable thermal margin limits. In-core fuel management staff must utilize various loading pattern strategies such as cross-core movement of fuel assemblies, multibatch enrichment schemes, and burnable absorbers as the primary means of controlling the radial power distribution. The utilization of fresh asymmetrically loaded gadolinia-bearing assemblies as a fuel management tool provides an additional means of controlling the radial power distribution. At Siemens Nuclear Power Corporation (SNP), fresh fuel assemblies fabricated with asymmetrically loaded gadolinia-bearing fuel rods have been used successfully for several cycles of reactor operation. Asymmetric assemblies are neutronically modeled using the same tools and models that SNP uses to model symmetrically loaded gadolinia-bearing fuel assemblies. The CASMO-2E code is used to produce the homogenized macroscopic assembly cross sections for the nodal core simulator. Optimum fuel pin locations within the asymmetrical assembly are determined using the pin-by-pin PDQ7 assembly core model for each new assembly design. The optimum pin location is determined by the rod loading that minimizes the peak-to-average pin power

Big bearings. Unsung hero; Kyodaina jikuuke. Hitome ni tsukanai hatarakimono

Energy Technology Data Exchange (ETDEWEB)

Nanba, S. [Koyo Seiko Co. Ltd., Osaka (Japan)

1997-03-05

This paper introduces examples of the use of big bearings. Bearings are divided largely into those used for radial load supporting and those used for thrust load supporting, while big bearings are often used for the latter usage. Thrust bearings include a cutter heat supporting bearing for tunnel excavator working underground, in addition to those used for swing motion of parabolic antennas and tower cranes. A bearing used in an excavator has an outer diameter of about half that of the excavator. The outer diameter of a shielding machine practically used in tunnel drilling currently has an outer diameter of 14,140 mm, and the outer diameter of the bearing is 7200 mm (bearing weighing 45 tons). Other big thrust bearings may include a swing tower swinging thrust bearing used in a continuous casting facility. Big radial bearings are used in iron and steel making facilities. This paper describes two examples of bearings used in this application. A spherical roller bearing to support converter trunion should be of an ultra big size to withstand total weight of about 1400 tons composed of a converter weight and weight of steel to be processed. A four-row cylindrical roller bearing to support the backup roll of a thick plate rolling mill is a bearing with durability against large loads to support reduction rolls whose size have become increasingly large. 2 refs., 5 figs.

Problematics of Reliability of Road Rollers

Science.gov (United States)

Stawowiak, Michał; Kuczaj, Mariusz

2018-06-01

This article refers to the reliability of road rollers used in a selected roadworks company. Information on the method of road rollers service and how the service affects the reliability of these rollers is presented. Attention was paid to the process of the implemented maintenance plan with regard to the machine's operational time. The reliability of road rollers was analyzed by determining and interpreting readiness coefficients.

System and method for conveying an assembly

KAUST Repository

Eitelhuber, Georg

2015-01-15

An apparatus, system, and method for conveying an assembly along a track. A rail can include a first planar side, a second planar side, and a third planar side. The first, second, and third planar sides can be arranged to form at least two acute angles. A carriage assembly can include a drive wheel and at least two roller sets. The drive wheel can be configured to contact the first planar side and is configured to translate the carriage assembly along the rail. The at least two roller sets can be configured to contact the two other sides to maintain the carriage in contact with the rail.

Roller-compacted concrete pavements.

Science.gov (United States)

2010-09-01

Roller-compacted concrete (RCC) gets its name from the heavy vibratory steel drum and rubber-tired rollers used to help compact it into its final form. RCC has similar strength properties and consists of the same basic ingredients as conventional con...

Wind Turbine Design Guideline DG03: Yaw and Pitch Rolling Bearing Life

Energy Technology Data Exchange (ETDEWEB)

Harris, T.; Rumbarger, J. H.; Butterfield, C. P.

2009-12-01

This report describes the design criteria, calculation methods, and applicable standards recommended for use in performance and life analyses of ball and roller (rolling) bearings for yaw and pitch motion support in wind turbine applications. The formulae presented here for rolling bearing analytical methods and bearing-life ratings are consistent with methods in current use by wind turbine designers and rolling-bearing manufacturers.

Vibration based blind identification of bearing failures for autonomous wireless sensor nodes

NARCIS (Netherlands)

Sanchez Ramirez, Andrea; Loendersloot, Richard; Tinga, Tiedo; Bregon, A.; Daigle, M.J.

2014-01-01

Despite all the attention received by maintainers, undetected roller bearings failures are still a major source of concern in relation with reliability losses and high maintenance costs. Because of that, bearing condition assessment through vibration monitoring remains an intensive topic of

Development of roller type side slip tester; Roller shiki side slip tester no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nishiyama, S [Hiroshima City Industrial Technology Institute, Hiroshima (Japan); Harada, S; Harada, K

1997-10-01

This paper presents a new development of roller type side slip tester (RTSSI). The test equipment consists of four parts, which are developed in this research. These are a roller part, a control part, a remote control part and a CRT part. In this study, we especially investigated the mechanism and performance between tire and roller. We analyzed the amount of side slip with various toe angles. The developed tester is examined under the conditions that is considered in industrial applications. We investigated the influences of toe angle, size of tire, pressure of tire, coefficient of friction between tire and roller, pushing force of tire, revolution velocity of roller, axle load and so on. The validity of the developed RTSST is confirmed under these conditions. It was found that the RTSST can be used in practical use. Some measurement results are presented in the form of parametric plots. And we also compared measurements data between the RTSST and that of flat type using several automobiles. 4 refs., 8 figs., 4 tabs.

On Working Capacity Criteria for Screw-Roller Mechanisms

Directory of Open Access Journals (Sweden)

D. S. Blinov

2015-01-01

Full Text Available Today roller-screw mechanisms (RSM are the most prospective motion converters from rotary to linear type. RSM manufacturers have suggested their design in the way, similar to the rolling bearings, in static and dynamic load ratings. The latter means that during long operations the main criterion of the RSM working capacity is fatigue spalling. However, this approach does not permit to consider temporal changes of the most critical performance parameters of the RSM (such as the axial play, the efficiency factor, the axial stiffness, the accuracy, the starting torque force for zero lash RSMs, etc. through calculations. The abovementioned method was not perfect, because the choice of the main criterion of RSM working capacity was wrong. The article proves that wear-resistance is the main criterion of RSM working capacity. The proof is the RSM efficiency factor equal to 80-88% on the average. The power loss occurs because of overcoming a sliding friction between multiple (from 300 to 1000 interfacing turns of thread on the screw and the rollers as well as on the rollers and the nut. That is why the RSMs are the screwtype rolling mechanisms with an essential portion of sliding friction. High-accuracy measurements taken using the device called a form-tracer for threaded pieces permitted to determine the essential changes on the profiles of turns of threads on the rollers (a straight-line portion appeared on the radial profile; these changes could emerge only from wear. Besides, the length of this portion increased with the increasing RSM operation time. The JSC “Moskvich” has examined the RSMs, which have been put out of operation after completing their service life as parts of robot welding machines. There were no traces of fatigue spalling found on the threaded surfaces of the RSM parts, while the sizes of the straight-line portions on the turns of the roller threads were much bigger than they were during the measurements after the initial

Low profile, high load vertical rolling positioning stage

Science.gov (United States)

Shu, Deming; Barraza, Juan

1996-01-01

A stage or support platform assembly for use in a synchrotron accurately positions equipment to be used in the beam line of the synchrotron. The support platform assembly includes an outer housing in which is disposed a lifting mechanism having a lifting platform or stage at its upper extremity on which the equipment is mounted. A worm gear assembly is located in the housing and is adapted to raise and lower a lifting shaft that is fixed to the lifting platform by an anti-binding connection. The lifting platform is moved vertically as the lifting shaft is moved vertically. The anti-binding connection prevents the shaft from rotating with respect to the platform, but does permit slight canting of the shaft with respect to the lifting platform so as to eliminate binding and wear due to possible tolerance mismatches. In order to ensure that the lifting mechanism does not move in a horizontal direction as it is moved vertically, at least three linear roller bearing assemblies are arranged around the outer-periphery of the lifting mechanism. One of the linear roller bearing assemblies can be adjusted so that the roller bearings apply a loading force against the lifting mechanism. Alternatively, a cam mechanism can be used to provide such a loading force.

Analysis of a spacecraft instrument ball bearing assembly lubricated by a perfluoroalkylether

Science.gov (United States)

Morales, W.; Jones, W. R., Jr.; Buckley, D. H.

1986-01-01

An analysis of a spacecraft instrument ball bearing assembly, subjected to a scanning life test, was performed to determine the possible case of rotational problems involving these units aboard several satellites. The analysis indicated an ineffective transfer of a fluorinated liquid lubricant from a phenolic retainer to the bearing balls. Part of the analysis led to a novel HPLC separation method employing a fluorinated mobile phase in conjunction with silica based size exclusion columns.

R+D works for the further development of high temperature reactors. (1) Captive bearing experiments for active magnetic bearings. (2) Captive bearing test for HTR blowers

International Nuclear Information System (INIS)

1991-01-01

When using active magnetic bearings as blower shaft bearings, blower motors and bearings must be protected against mechanical damage in case of faults (example: total electrical supply failure due to the supply cables breaking). So-called captive bearings are provided, in order to be able to shut the blowers down safely in such faults. These captive bearings are roller bearings which are additionally fitted in the area of the blower shaft bearings, to prevent mechanical contact between the blower rotor and stator. As there was little experience available for the given boundary conditions, such as - speed, - acceleration, - bearing load, - bearing dimensions, - ambient conditions, appropriate development and tests had to be carried out. It was important to determine suitable captive bearings and the necessary ambient conditions, which will make it possible to support the failures of the magnetic bearings to be expected in 40 years' operation of the reactor without damage and to meet the requirements of the captive bearings. (orig./GL) [de

Analisa Beban Kerja Dan Gaya Dinamis Pada Round Roller Dan Sliding Roller Untuk Sistem CVT (Continuously Variable Transmission Sepeda Motor Matic

Directory of Open Access Journals (Sweden)

Ahmad Bagus Prasojo

2017-01-01

Full Text Available Primary shave weight atau sering disebut roller merupakan salah satu komponen dari sistem CVT pada motor matik yang sering mengalami kerusakan, baik itu aus maupun crack atau pecah. Metodologi yang dilakukan pada penelitian ini adalah menganalisa beban kerja (gaya yang dialami oleh roller. Selanjutnya akan dihitung besar tegangan (stress yang terjadi pada roller menggunakan teori tegangan kontak (contact stress. Kemudian analisa akan dilanjutkan menggunakan teori kelelahan (fatigue. Gaya normal yang didapat pada posisi stasioner sebesar 37,268 N dan posisi puncak sebesar 525,279 N. Untuk total tegangan ekivalen yang terjadi berbeda dikarenakan luasan kontaknya, round roller dengan luasan kontak yang lebih kecil menghasilkan total tegangan yang lebih besar yaitu 21,423 MPa sedangkan sliding roller sebesar 14,559 MPa. Dengan frekuensi real pembebanan roller sebesar 0,0667 Hz dan berdasarkan teori kelelahan Gerber stress amplitude round roller didapatkan 8,8756 Mpa dan untuk sliding roller sebesar 6,195 Mpa. Jadi setelah stress amplitude diplotkan pada sn-curve PTFE hasil prediksi umur untuk round roller adalah 4,081 ≈ 4 bulan dan untuk sliding roller adalah 5,89 ≈ 6 bulan.

Simulation-driven machine learning: Bearing fault classification

Science.gov (United States)

Sobie, Cameron; Freitas, Carina; Nicolai, Mike

2018-01-01

Increasing the accuracy of mechanical fault detection has the potential to improve system safety and economic performance by minimizing scheduled maintenance and the probability of unexpected system failure. Advances in computational performance have enabled the application of machine learning algorithms across numerous applications including condition monitoring and failure detection. Past applications of machine learning to physical failure have relied explicitly on historical data, which limits the feasibility of this approach to in-service components with extended service histories. Furthermore, recorded failure data is often only valid for the specific circumstances and components for which it was collected. This work directly addresses these challenges for roller bearings with race faults by generating training data using information gained from high resolution simulations of roller bearing dynamics, which is used to train machine learning algorithms that are then validated against four experimental datasets. Several different machine learning methodologies are compared starting from well-established statistical feature-based methods to convolutional neural networks, and a novel application of dynamic time warping (DTW) to bearing fault classification is proposed as a robust, parameter free method for race fault detection.

Space Station alpha joint bearing

Science.gov (United States)

Everman, Michael R.; Jones, P. Alan; Spencer, Porter A.

1987-01-01

Perhaps the most critical structural system aboard the Space Station is the Solar Alpha Rotary Joint which helps align the power generation system with the sun. The joint must provide structural support and controlled rotation to the outboard transverse booms as well as power and data transfer across the joint. The Solar Alpha Rotary Joint is composed of two transition sections and an integral, large diameter bearing. Alpha joint bearing design presents a particularly interesting problem because of its large size and need for high reliability, stiffness, and on orbit maintability. The discrete roller bearing developed is a novel refinement to cam follower technology. It offers thermal compensation and ease of on-orbit maintenance that are not found in conventional rolling element bearings. How the bearing design evolved is summarized. Driving requirements are reviewed, alternative concepts assessed, and the selected design is described.

The dynamic analysis of drum roll lathe for machining of rollers

Science.gov (United States)

Qiao, Zheng; Wu, Dongxu; Wang, Bo; Li, Guo; Wang, Huiming; Ding, Fei

2014-08-01

An ultra-precision machine tool for machining of the roller has been designed and assembled, and due to the obvious impact which dynamic characteristic of machine tool has on the quality of microstructures on the roller surface, the dynamic characteristic of the existing machine tool is analyzed in this paper, so is the influence of circumstance that a large scale and slender roller is fixed in the machine on dynamic characteristic of the machine tool. At first, finite element model of the machine tool is built and simplified, and based on that, the paper carries on with the finite element mode analysis and gets the natural frequency and shaking type of four steps of the machine tool. According to the above model analysis results, the weak stiffness systems of machine tool can be further improved and the reasonable bandwidth of control system of the machine tool can be designed. In the end, considering the shock which is caused by Z axis as a result of fast positioning frequently to feeding system and cutting tool, transient analysis is conducted by means of ANSYS analysis in this paper. Based on the results of transient analysis, the vibration regularity of key components of machine tool and its impact on cutting process are explored respectively.

The 1982 epidemic--roller skating injuries.

Science.gov (United States)

Bunker, T. D.

1983-01-01

A series of 100 roller skating injuries is presented. Roller skating injuries have been occurring at a higher rate than the previously reported skateboarding epidemic of 1977. The severity of injury has been lower, 32% fractures and dislocations occurring whilst roller skating, compared to 60% whilst skateboarding. In particular a striking reduction is seen in ankle fractures. Fifty questionnaires detailing method of injury were analysed. Images p205-a Fig. 1 Fig. 2 PMID:6652406

Development of ceramic roller bush for diesel fuel injection pump; Nenryo funsha pump yo ceramics sei roller bush no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Noda, K; Kamiya, S; Fujimura, M; Tsuzuki, M [Toyota Motor Corp., Aichi (Japan); Taniguchi, K [Denso Corp., Aichi (Japan)

1997-10-01

Silicon nitride ceramics have been applied to roller bush for diesel fuel injection pump in order to improve the seizure resistance. It was found that ceramic roller bush made it possible to improve the seizure load by more than three times as compared to conventional metal roller bush when the kerosene was used as lubricant The ceramic roller bush proved to be durable under engine operating conditions. 6 refs., 13 figs., 1 tab.

On-line surveillance of lubricants in bearings by means of surface acoustic waves.

Science.gov (United States)

Lindner, Gerhard; Schmitt, Martin; Schubert, Josephine; Krempel, Sandro; Faustmann, Hendrik

2010-01-01

The acoustic wave propagation in bearings filled with lubricants and driven by pulsed excitation of surface acoustic waves has been investigated with respect to the presence and the distribution of different lubricants. Experimental setups, which are based on the mode conversion between surface acoustic waves and compression waves at the interface between a solid substrate of the bearing and a lubricant are described. The results of preliminary measurements at linear friction bearings, rotation ball bearings and axial cylinder roller bearings are presented.

ROLLER RIG TESTING AT THE CZECH TECHNICAL UNIVERSITY

Directory of Open Access Journals (Sweden)

J. Kalivoda

2016-08-01

Full Text Available Purpose. Although the advancements in computer simulation technology have paved way to provide very reliable simulation results, track tests still play an essential role during the process of development and homologation of any railway vehicle. On the other hand, track tests depend on weather conditions, are difficult to organize and are not suitable for testing vehicles in critical situations. On a roller rig, the tested vehicle is longitudinally fixed and a track is replaced by rotating rollers. Such device offer testing of railway vehicle running dynamics in safe and stable laboratory environment. The purpose of an article is to investigate and describe roller rig testing at the Czech technical university in Prague (CTU. Methodology. In the paper it is shown the history of development of the scaled CTU roller rig from the earlier stages until the current projects for which the CTU roller rig is utilized for. The current design of the experimental bogie, roller rig, sensors instrumentation and types of experiments conducted at the CTU roller rig are described in more detail. Findings. Although the differences in vehicle behaviour on a track and a scaled model on a roller rig are not negligible, scaled roller rig experiments are found as a relatively inexpensive way for verification and demonstration of computer simulations results. They are especially useful for verification of multibody system simulations (MBS of entirely new running gear concepts. Originality. The CTU roller rig is currently used for the experiments with active controlled wheelset guidance. According to simulations results published in many papers such systems offer, in principle, better performance compared to conventional passive vehicles. However, utilization and testing of active controlled wheelset guidance on vehicles is still rare. CTU roller rig serves as a tool to verify computer simulations and demonstrate benefits of active wheelset guidance. Practical value

78 FR 58996 - Tapered Roller Bearings from the People's Republic of China: Notice of Court Decision Not in...

Science.gov (United States)

2013-09-25

... Sawblades Mfrs. Coalition v. United States, 626 F.3d 1374 (Fed. Cir. 2010) (``Diamond Sawblades''), the... a complaint with the CIT to challenge various aspects of the Final Results. \\2\\ Tapered Roller...

VIRTUAL MODEL OF A ROLLER CONVEYOR INTEGRATED INTO A LOGISTIC FLOW

Directory of Open Access Journals (Sweden)

POPESCU Adrian

2015-11-01

Full Text Available In this article is presented, with the help of graphics, a logistic flow for palletizing and wrapping operations. The loaded pallets are transported by means of a roller conveyor. Creating the virtual model for the conveyer allows us to emphasize the compatibility elements between on the one hand the mechanical assemblies of the flow components and on the other hand the subassemblies of the conveyer structure. The paper has focused on the presentation of the conveyor specific assembly and how are placed the sensors on the mechanical structure of the conveyor. Finally, the main working phases are graphically presented within the flow, highlighting the loaded pallet positions in the flow.

Reliability of agriculture universal joint shafts based on temperature measuring in universal joint bearing assemblies

Directory of Open Access Journals (Sweden)

Аleksandar Asonja

2015-03-01

Full Text Available This paper presents a research into reliability calculations of agriculture double universal joint shafts based on temperature measuring in cardan-type universal joint bearing assemblies. Special laboratory equipment was developed for this research which is presented in the paper. The objective of this research was to test the real life span of universal joint shafts in the laboratory and in field, to obtain the results which can be used to improve the reliability of universal joint shafts. If the presented research were used along with maintenance measures recommended in the paper and with proper use, the level of reliability of the shafts would be 2.1 times higher. The presented results of the research showed that needle bearings, i.e. bearing assemblies of the joints, are the most critical elements on universal joint shafts and are possible causes of their lower reliability. The second universal joint is the part with the lowest reliability in the observed technical system.

Ice-skating and roller disco injuries in Dublin.

OpenAIRE

Horner, C.; McCabe, M. J.

1984-01-01

A comparative study was carried out on a series of 72 ice-skating and 57 roller skating injuries over a sixteen month period. The average patient age was 20.5 years in the ice-skating group and 16.5 years in the roller skating group. Females predominated in both groups accounting for 72% of ice-skaters injured and 77% of roller skaters injured. Ice-skaters sustained more serious injuries than roller skaters as was evident from the significant difference in fracture numbers in the two groups. ...

Failure Analysis and Thermochemical Surface Engineering of Bearings in the Wind Turbine Drivetrain

DEFF Research Database (Denmark)

West, Ole H.E.; Dahl, Kristian Vinter; Christiansen, Thomas Lundin

charged rollers to reproduce WEC formation. The influence of different hoop stress levels was studied. The fracture surfaces as well as formed WECs were investigated. A detrimental effect of higher hoop stress levels on roller lifetime was found and based on the analysis of the formed WECs an incremental...... the influence of different alloying concepts, prior heat treatments and nitriding parameters on the case properties. With optimum nitriding conditions a maximum nitriding depth of 800 μm was achieved, without formation of a thick porous compound layer. The build-up of near surface compressive stresses...... was confirmed by synchrotron X–ray diffraction stress analysis. The performance of surface engineered rollers was evaluated by RCF testing under conditions that are known to provoke failure in rollers made from a standard bearing steel. One of the nitrided materials showed promising results....

Dynamic modeling of moment wheel assemblies with nonlinear rolling bearing supports

Science.gov (United States)

Wang, Hong; Han, Qinkai; Luo, Ruizhi; Qing, Tao

2017-10-01

Moment wheel assemblies (MWA) have been widely used in spacecraft attitude control and large angle slewing maneuvers over the years. Understanding and controlling vibration of MWAs is a crucial factor to achieving the desired level of payload performance. Dynamic modeling of a MWA with nonlinear rolling bearing supports is conducted. An improved load distribution analysis is proposed to more accurately obtain the contact deformations and angles between the rolling balls and raceways. Then, the bearing restoring forces are then obtained through iteratively solving the load distribution equations at every time step. The effects of preload condition, surface waviness, Hertz contact and elastohydrodynamic lubrication could all be reflected in the nonlinear bearing forces. Considering the mass imbalances of the flywheel, flexibility of supporting structures and rolling bearing nonlinearity, the dynamic model of a typical MWA is established based upon the energy theorem. Dynamic tests are conducted to verify the nonlinear dynamic model. The influences of flywheel mass eccentricity and inner/outer waviness amplitudes on the dynamic responses are discussed in detail. The obtained results would be useful for the design and vibration control of the MWA system.

Hierarchical self-assembly of a bow-shaped molecule bearing self-complementary hydrogen bonding sites into extended supramolecular assemblies.

Science.gov (United States)

Ikeda, Masato; Nobori, Tadahito; Schmutz, Marc; Lehn, Jean-Marie

2005-01-07

The bow-shaped molecule 1 bearing a self-complementary DAAD-ADDA (D=donor A=acceptor) hydrogen-bonding array generates, in hydrocarbon solvents, highly ordered supramolecular sheet aggregates that subsequently give rise to gels by formation of an entangled network. The process of hierarchical self-assembly of compound 1 was investigated by the concentration and temperature dependence of UV-visible and (1)H NMR spectra, fluorescence spectra, and electron microscopy data. The temperature dependence of the UV-visible spectra indicates a highly cooperative process for the self-assembly of compound 1 in decaline. The electron micrograph of the decaline solution of compound 1 (1.0 mM) revealed supramolecular sheet aggregates forming an entangled network. The selected area electronic diffraction patterns of the supramolecular sheet aggregates were typical for single crystals, indicative of a highly ordered assembly. The results exemplify the generation, by hierarchical self-assembly, of highly organized supramolecular materials presenting novel collective properties at each level of organization.

Ice-skating and roller disco injuries in Dublin.

Science.gov (United States)

Horner, C.; McCabe, M. J.

1984-01-01

A comparative study was carried out on a series of 72 ice-skating and 57 roller skating injuries over a sixteen month period. The average patient age was 20.5 years in the ice-skating group and 16.5 years in the roller skating group. Females predominated in both groups accounting for 72% of ice-skaters injured and 77% of roller skaters injured. Ice-skaters sustained more serious injuries than roller skaters as was evident from the significant difference in fracture numbers in the two groups. Ice-skating fractures accounted for 40% of all injuries while roller skating fractures were only 14% of their total injuries. The majority of ice-skating fractures occurred in females. As a result of our study we recommended several preventative measures. Images p207-a p207-b PMID:6487948

21 CFR 870.4370 - Roller-type cardiopulmonary bypass blood pump.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Roller-type cardiopulmonary bypass blood pump. 870... Roller-type cardiopulmonary bypass blood pump. (a) Identification. A roller-type cardiopulmonary bypass blood pump is a device that uses a revolving roller mechanism to pump the blood through the...

Engine testing of ceramic cam-roller followers

Energy Technology Data Exchange (ETDEWEB)

Kalish, Y. (Detroit Diesel Corp., MI (United States))

1992-04-01

For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

GAS BEARING

Science.gov (United States)

Skarstrom, C.W.

1960-09-01

A gas lubricated bearing for a rotating shaft is described. The assembly comprises a stationary collar having an annular member resiliently supported thereon. The collar and annular member are provided with cooperating gas passages arranged for admission of pressurized gas which supports and lubricates a bearing block fixed to the rotatable shaft. The resilient means for the annular member support the latter against movement away from the bearing block when the assembly is in operation.

Enhanced DET-Based Fault Signature Analysis for Reliable Diagnosis of Single and Multiple-Combined Bearing Defects

Directory of Open Access Journals (Sweden)

In-Kyu Jeong

2015-01-01

Full Text Available To early identify cylindrical roller bearing failures, this paper proposes a comprehensive bearing fault diagnosis method, which consists of spectral kurtosis analysis for finding the most informative subband signal well representing abnormal symptoms about the bearing failures, fault signature calculation using this subband signal, enhanced distance evaluation technique- (EDET- based fault signature analysis that outputs the most discriminative fault features for accurate diagnosis, and identification of various single and multiple-combined cylindrical roller bearing defects using the simplified fuzzy adaptive resonance map (SFAM. The proposed comprehensive bearing fault diagnosis methodology is effective for accurate bearing fault diagnosis, yielding an average classification accuracy of 90.35%. In this paper, the proposed EDET specifically addresses shortcomings in the conventional distance evaluation technique (DET by accurately estimating the sensitivity of each fault signature for each class. To verify the efficacy of the EDET-based fault signature analysis for accurate diagnosis, a diagnostic performance comparison is carried between the proposed EDET and the conventional DET in terms of average classification accuracy. In fact, the proposed EDET achieves up to 106.85% performance improvement over the conventional DET in average classification accuracy.

Numerically Analysed Thermal Condition of Hearth Rollers with the Water-Cooled Shaft

Directory of Open Access Journals (Sweden)

A. V. Ivanov

2016-01-01

Full Text Available Continuous furnaces with roller hearth have wide application in the steel industry. Typically, furnaces with roller hearth belong to the class of medium-temperature heat treatment furnaces, but can be used to heat the billets for rolling. In this case, the furnaces belong to the class of high temperature heating furnaces, and their efficiency depends significantly on the reliability of the roller hearth furnace. In the high temperature heating furnaces are used three types of watercooled shaft rollers, namely rollers without insulation, rollers with insulating screens placed between the barrel and the shaft, and rollers with bulk insulation. The definition of the operating conditions of rollers with water-cooled shaft greatly facilitates the choice of their design parameters when designing. In this regard, at the design stage of the furnace with roller hearth, it is important to have information about the temperature distribution in the body of the rollers at various operating conditions. The article presents the research results of the temperature field of the hearth rollers of metallurgical heating furnaces. Modeling of stationary heat exchange between the oven atmosphere and a surface of rollers, and between the cooling water and shaft was executed by finite elements method. Temperature fields in the water-cooled shaft rollers of various designs are explored. The water-cooled shaft rollers without isolation, rollers with screen and rollers with bulk insulation, placed between the barrel and the water-cooled shaft were investigated. Determined the change of the thermo-physic parameters of the coolant, the temperature change of water when flowing in a pipe and shaft, as well as the desired pressure to supply water with a specified flow rate. Heat transfer coefficients between the cooling water and the shaft were determined directly during the solution based on the specified boundary conditions. Found that the greatest heat losses occur in the

Kinematics and Dynamics of Roller Chain Drives

DEFF Research Database (Denmark)

Fuglede, Niels

There are two main subjects of this work: Kinematic and dynamic modeling and analysis of roller chain drives. In the kinematic analysis we contribute first with a complete treatment of the roller chain drive modeled as a four-bar mechanism. This includes a general, exact and approximate analysis...... which is useful for predicting the characteristic loading of the roller chain drive. As a completely novel contribution, a kinematic model and analysis is presented which includes both spans and sprockets in a simple chain drive system. A general procedure for determination of the total wrapping length...... is presented, which also allows for exact sprocket center positions for a chain with a given number of links. Results show that the total chain wrapping length varies periodically with the tooth frequency. These results are of practical importance to both the design, installation and operation of roller chain...

Roller-chain Drives Mechanics using Multibody Dynamics Tools

DEFF Research Database (Denmark)

Ambrosio, Jorge A. C.; Hansen, John Michael

1999-01-01

An integrated model for the simulation of roller-chain drives based on a multibody dynamics methodology is presented here in order to describeits complex dynamic behavior. The chain is modeled by masses lumped at the roller locations and connected by translational spring-damper elements in order ...... engagement on the sprockets responsible for the polygonal effect is thoroughly analyzed and the induced impulsive forces developed during that action are treated by a strategy where kinematic constraints between sprockets and rollers are added and deleted....

Development testing of high temperature bearings for SP-100 control drive assemblies

Science.gov (United States)

Dalcher, Alfred W.; Kjaer-Olsen, Christian G.; Martinez, Carlos; Ogawa, Stanley Y.; Springer, Dwight R.; Yaspo, Robert

1992-01-01

Initial phases of two distinct SP-100 control drive assembly bearing test programs were successfully completed at elevated temperature in vacuum. The first was for the reflector drive line spherical self-aligning bearings. Each bearing consisted of a carbon-graphite ball mounted on an aluminum oxide-coated Ta-10%W shaft, captured by an aluminum oxide-coated Ta-10%W socket. One set of these bearings was exposed to temperatures up to 1180K (1665°F) at 1.33×10-6 Pa (1×10-8 torr) and subjected to 38000 cycles of motion. Friction coefficients were found to be between 0.11 and 0.25 over the full range of operation. Overall performance of the bearings was excellent, with only slight wear observed. The second test program was for the safety rod slider bearing. Zirconium carbide coated Nb-1%Zr bearings pads were stroked inside a molybdenum tube at temperatures up to 1422 K (2100°F) at ˜1.33×10-6 Pa with a normal load of 1.02 Kg between each sliding surface. Coefficients of sliding friction were found to increase from 0.90 at 293 K to 1.20 at 1422 K prior to high temperature dwells. Results were consistent over the range of stroke velocities; 5.1 to 51 mm (0.2 to 2.0 inches) per second. Following dwells of 92, 72, and 110 hours at 1422 K, static friction coefficients as high as 5.4 were observed prior to initiation of sliding, after which sliding friction coefficients of ˜1.6 were seen. Breakaway forces were well within the actuator design limits.

A General Case to Determine Dimensions and Their Tolerance Zones for the Thread Parts of Epicyclic Roller-Screw Mechanisms

Directory of Open Access Journals (Sweden)

D. S. Blinov

2017-01-01

Full Text Available The most important trend in the development of aerospace industry is to increase load capacity of mechanisms, assemblies, and parts without increasing their size and weight. The above is also true for widely used in aircrafts and the most promising up to date Epicyclic Roller-Screw Mechanisms (ERSM that convert rotational movement into translational one. Previously (in the article, it was proposed to increase the load capacity (approximately by 15% through reduction of included angle of ERSM threaded parts from 90° to 70°.However, such improvement of ERSM will change dimensions of the mechanism parts and its parameters and characteristics (efficiency factor, position of initial point of contact of the conjugated thread turns and parameters of their contact interaction, as well as kinematic parameters, which will require additional studies. If we take into account the priority of these studies, then surely we must begin with development of technique to determine dimensions of the ERSM main parts and their tolerance zones because we need drawings to manufacture and test the upgraded ERSM. We have developed a technique to calculate dimensions of the main parts of ERSM and associated tolerance zones that takes in to account the change of included angle of threaded parts of the mechanism and radius of circular arc according to which roller thread profile has been fulfilled. So the proposed technique is the general one in comparison with the previous ones.This technique uses various conditions and equations to determine dimensions of parts and associated tolerance zones. For example, a nut encircles a screw with rollers, and their dimensions form a closed dimension chain, in which the dimensions and associated tolerances must be such as to ensure ERSM assembling, on the one hand, and, on the other hand the backlash of the mechanism should be minimal to ensure high load capacity, kinematic accuracy, and rigidity of ERSM. We used the following

A FILTRATION METHOD AND APPARATUS INCLUDING A ROLLER WITH PORES

DEFF Research Database (Denmark)

2008-01-01

The present invention offers a method for separating dry matter from a medium. A separation chamber is at least partly defined by a plurality of rollers (2,7) and is capable of being pressure regulated. At least one of the rollers is a pore roller (7) having a surface with pores allowing permeabi...

Fatigue life of drilling bit bearings under arbitrary random loads

Energy Technology Data Exchange (ETDEWEB)

Talimi, M.; Farshidi, R. [Calgary Univ., AB (Canada)

2009-07-01

A fatigue analysis was conducted in order to estimate the bearing life of a roller cone rock bit under arbitrary random loads. The aim of the study was to reduce bearing failures that can interrupt well operations. Fatigue was considered as the main reason for bearing failure. The expected value of cumulative fatigue damage was used to estimate bearing life. An equation was used to express the relation between bearing life and bearing load when the bearing was subjected to a steady load and constant speed. The Palmgren-Miner hypothesis was used to determine the ultimate tensile strength of the material. The rain flow counting principle was used to determine distinct amplitude cycles. Hertzian equations were used to determine maximum stress loads. Fourier series were used to obtain simple harmonic functions for estimating stress-life relations. It was concluded that the method can be used during the well planning phase to prevent bearing failures. 6 refs.

Removable bearing arrangement for a wind turbine generator

Science.gov (United States)

Bagepalli, Bharat Sampathkumaran; Jansen, Patrick Lee; Gadre, Aniruddha Dattatraya

2010-06-15

A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

Roller compaction of moist pharmaceutical powders.

Science.gov (United States)

Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

2010-05-31

The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Simulation modeling of wheeled vehicle dynamics on the stand "Roller"

Directory of Open Access Journals (Sweden)

G. O. Kotiev

2014-01-01

Full Text Available The tests are an integral part of the wheeled vehicle design, manufacturing, and operation. The need for their conducting arises from the research and experimental activities to assess the qualitative and quantitative characteristics of the vehicles in general, as well as the individual components and assemblies. It is obvious that a variety of design features of wheeled vehicles request a development of methods both for experimental studies and for creating the original bench equipment for these purposes.The main positive feature of bench tests of automotive engineering is a broad capability to control the combinations of traction loads, speed rates, and external input conditions. Here, the steady state conditions can be used for a long time, allowing all the necessary measurements to be made, including those with video and photo recording experiment.It is known that the benefits of test "M" type (using a roller dynamometer include a wide range of test modes, which do not depend on the climatic conditions, as well as a capability to use a computer-aided testing programs. At the same time, it is known that the main drawback of bench tests of full-size vehicle is that the tire rolling conditions on the drum mismatch to the real road pavements, which are difficult to simulate on the drum surface. This problem can be solved owing to wheeled vehicle tests at the benches "Roller" to be, in efficiency, the most preferable research method. The article gives a detailed presentation of developed at BMSTU approach to its solving.Problem of simulation mathematical modeling has been solved for the vehicle with the wheel formula 8 × 8, and individual wheel-drive.The simulation results have led to the conclusion that the proposed principle to simulate a vehicle rolling on a smooth non-deformable support base using a bench " Roller " by simulation modeling is efficient.

Salmonella transfer during pilot plant scale washing and roller conveying of tomatoes.

Science.gov (United States)

Wang, Haiqiang; Ryser, Elliot T

2014-03-01

Salmonella transfer during washing and roller conveying of inoculated tomatoes was quantified using a pilot scale tomato packing line equipped with plastic, foam, or brush rollers. Red round tomatoes (2.3 kg) were dip inoculated with Salmonella enterica serovar Typhimurium LT2 (avirulent) (4 log CFU/g), air dried for 2 h, and then washed in sanitizer-free water for 2 min. Inoculated tomatoes were then passed single file over a 1.5-m conveyor equipped with plastic, foam, or brush rollers followed by 25 previously washed uninoculated tomatoes. Tomato samples were collected after 2 min of both washing and roller conveying, with all 25 uninoculated tomatoes collected individually after conveying. Roller surface samples were collected before and after conveying the uninoculated tomatoes. Both tomato and surface samples were quantitatively examined for Salmonella by direct plating or membrane filtration using xylose lysine Tergitol 4 agar. Regardless of the roller type, Salmonella populations on inoculated tomatoes did not significantly (P conveyors. After conveying uninoculated tomatoes over contaminated foam rollers, 96% of the 25 tomatoes were cross-contaminated with Salmonella at >100 CFU per tomato. With plastic rollers, 24 and 76% of tomatoes were cross-contaminated with Salmonella at 10 to 100 and 1 to 10 CFU per tomato, respectively. In contrast, only 8% of 25 tomatoes were cross-contaminated with brush rollers with Salmonella populations of 1 to 10 CFU per tomato. Overall, cross-contamination was greatest with foam, followed by plastic and brush rollers (P < 0.05). Adding peroxyacetic acid or chlorine to the wash water significantly decreased cross-contamination during tomato conveying, with chlorine less effective in controlling Salmonella on foam compared with plastic and brush rollers.

Significant changes in the skin microbiome mediated by the sport of roller derby

Directory of Open Access Journals (Sweden)

James F. Meadow

2013-03-01

Full Text Available Diverse bacterial communities live on and in human skin. These complex communities vary by skin location on the body, over time, between individuals, and between geographic regions. Culture-based studies have shown that human to human and human to surface contact mediates the dispersal of pathogens, yet little is currently known about the drivers of bacterial community assembly patterns on human skin. We hypothesized that participation in a sport involving skin to skin contact would result in detectable shifts in skin bacterial community composition. We conducted a study during a flat track roller derby tournament, and found that teammates shared distinct skin microbial communities before and after playing against another team, but that opposing teams’ bacterial communities converged during the course of a roller derby bout. Our results are consistent with the hypothesis that the human skin microbiome shifts in composition during activities involving human to human contact, and that contact sports provide an ideal setting in which to evaluate dispersal of microorganisms between people.

Errors of car wheels rotation rate measurement using roller follower on test benches

Science.gov (United States)

Potapov, A. S.; Svirbutovich, O. A.; Krivtsov, S. N.

2018-03-01

The article deals with rotation rate measurement errors, which depend on the motor vehicle rate, on the roller, test benches. Monitoring of the vehicle performance under operating conditions is performed on roller test benches. Roller test benches are not flawless. They have some drawbacks affecting the accuracy of vehicle performance monitoring. Increase in basic velocity of the vehicle requires increase in accuracy of wheel rotation rate monitoring. It determines the degree of accuracy of mode identification for a wheel of the tested vehicle. To ensure measurement accuracy for rotation velocity of rollers is not an issue. The problem arises when measuring rotation velocity of a car wheel. The higher the rotation velocity of the wheel is, the lower the accuracy of measurement is. At present, wheel rotation frequency monitoring on roller test benches is carried out by following-up systems. Their sensors are rollers following wheel rotation. The rollers of the system are not kinematically linked to supporting rollers of the test bench. The roller follower is forced against the wheels of the tested vehicle by means of a spring-lever mechanism. Experience of the test bench equipment operation has shown that measurement accuracy is satisfactory at small rates of vehicles diagnosed on roller test benches. With a rising diagnostics rate, rotation velocity measurement errors occur in both braking and pulling modes because a roller spins about a tire tread. The paper shows oscillograms of changes in wheel rotation velocity and rotation velocity measurement system’s signals when testing a vehicle on roller test benches at specified rates.

Engine testing of ceramic cam-roller followers. Final report

Energy Technology Data Exchange (ETDEWEB)

Kalish, Y. [Detroit Diesel Corp., MI (United States)

1992-04-01

For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

Failure of GIMBAL bearing in directional GYRO

International Nuclear Information System (INIS)

Pervaiz, R.; Baig, N.A.; Shahid, M.; Ahmad, A.; Chohan, G.Y.

2003-01-01

This paper relates to the directional gyro of a sensing device used in indigenously developed surface-to-surface missile. The assembling of more than one thousand components in the form of several sub assemblies including hundreds of silver solders of this device was done in the hundred-thousands-class clean room according to assembly procedure. Whereas more than twenty bearings including gimbals bearings were assembled in the ten-thousands-class clean room after inspection/ testing them on beating testing system as per routine. The device was entered in testing and adjustment phase after successful completion of assembly work. The directional gyro qualified all the tests except the most critical one, the drift-rate. The drift-rate of outer gimbal was 60% more than permissible limit whereas drift-rate of inner gimbal was found O.K. It was diagnosed that at least one inner gimbal bearing out of two had some problem. The results were same after rebalancing of gimbals three times. The directional gyro was disassembled in clean room and the radial-thrust-bearing was recovered and flange bearing which are inner gimbal bearings. They were checked on bearing testing system and it was found that flange-bearing had more friction than permissible limit and hence rejected but radial thrust bearing were declared O.K. The gyro was reassembled with new O.K. flange bearing and the assembly work was completed in all respects. The sensing device qualified all the tests including the drift-rate. This case study is being presented to emphasize the importance of careful assembly of gyro in clean environment. (author)

Direct fabrication of rigid microstructures on a metallic roller using a dry film resist

International Nuclear Information System (INIS)

Jiang, Liang-Ting; Huang, Tzu-Chien; Chang, Chih-Yuan; Ciou, Jian-Ren; Yang, Sen-Yeu; Huang, Po-Hsun

2008-01-01

This paper presents a novel method to fabricate a metallic roller mold with microstructures on its surface using a dry film resist (DFR). The DFR is laminated uniformly onto the curvy surface of a copper roller. After that, the micro-scale photoresist on the surface of the roller can be patterned by non-planar lithography using a flexible film photomask, followed by ferric chloride wet etching to obtain the desired microstructures. This method overcomes the uniformity issue of photoresist coating on rollers, and solves the molds sliding problem during the embossing process because the microstructures are fabricated directly on the roller surface. Furthermore, the rigid metallic roller mold has excellent strength durability and temperature endurance, which can be used in roller hot embossing with a high embossing pressure. The fabricated microstructure roller mold is used as a mold in the hybrid extrusion roller embossing process and successfully fabricates uniform micro-scale prominent line arrays on PC films. This result proves that the roller fabricated by this method can be successfully used in roller embossing for microstructure mass production. The excellent flatness of dry film resist laminating is the key in this fabrication process. The flexible film photomask can be easily designed using CAD software; this roller fabrication method enhances the design flexibility and reduces the cost and time

Diagnosis of bearing creep in wind turbine gearboxes

DEFF Research Database (Denmark)

Skrimpas, Georgios Alexandros; Liu, Zhenyan; Hilmisson, Reynir

2016-01-01

One of the most wide spread gearbox topologies in the wind energy sector consists of a slow rotating planetary stage, an intermediate speed parallel stage and finally a high speed parallel stage driving the generator rotor. The shafts of the two latter stages are supported by ball or roller...... bearings where their outer races are fixed to the gearbox and their inner races rotate at the corresponding shaft speed. Bearing inner race defects are frequently encountered in gearboxes leading to either replacement of the whole unit or exchange of the shaft or bearing where feasible. The present work...... deals with the evaluation of the development of an inner race defect from surface pitting to race axial crack resulting in excessive rotational looseness, also referred to as bearing creep. It is shown that an inner race defect can be identified efficiently at an early stage by employing well known...

Roller Locking Brake

Science.gov (United States)

Vranish, John M.

1993-01-01

Roller locking brake is normally braking rotary mechanism allowing free rotation when electromagnet in mechanism energized. Well suited to robots and other machinery which automatic braking upon removal of electrical power required. More compact and reliable. Requires little electrical power to maintain free rotation and exhibits minimal buildup of heat.

A study on rheological characteristics of roller milled fenugreek fractions.

Science.gov (United States)

Sakhare, Suresh D; Inamdar, Aashitosh A; Prabhasankar, P

2016-01-01

Fenugreek seeds were fractionated by roller milling to get various fractions. The roller milled fractions and whole fenugreek flour (WFF) were evaluated for the flow behavior and time-dependent flow properties using a rotational viscometer at the temperatures of 10-60 (0)C. The samples subjected to a programmed shear rate increase linearly from 0 to 300 s(-1) in 3 min and successive decrease linearly shear rate from 300 s(-1) to 0 in 3 min. The roller milled fractions and WFF paste exhibited non-Newtonian pseudoplastic behavior. Difference in hysteresis loop area was observed among the roller milled fractions and WFF, being more noticeable at lower temperatures. Power law and Casson models were used to predict flow properties of samples. The power law model described well the flow behavior of the roller milled fractions and WFF at temperatures tested. Except flour (FL) fraction, consistency coefficient, m, increased with the temperature both in the forward and backward measurements. The roller milled fractions and WFF exhibited rheopectic behavior that increased viscosity with increasing the shear speed and the temperature. For all the sample tested, initial shear stress increased with increase in shear rate and temperature.

Model Specification for Rework of Aircraft Engine, Power Transmission, and Accessory/Auxiliary Ball and Roller Bearings

Science.gov (United States)

Zaretsky, Erwin V.; Branzai, Emanuel V.

2007-01-01

This document provides a model specification for the rework and/or repair of bearings used in aircraft engines, helicopter main power train transmissions, and auxiliary bearings determined to be critical by virtue of performance, function, or availability. The rolling-element bearings to be processed under the provisions of this model specification may be used bearings removed after service, unused bearings returned from the field, or certain rejected bearings returned for reinspection and salvage. In commercial and military aircraft application, it has been a practice that rolling-element bearings removed at maintenance or overhaul be reworked and returned to service. Depending on the extent of rework and based upon theoretical analysis, representative life factors (LF) for bearings subject to rework ranged from 0.87 to 0.99 the lives of new bearings. Based on bearing endurance data, 92 percent of the bearing sets that would be subject to rework would result in L(sub 10) lives equaling and/or exceeding that predicted for new bearings. The remaining 8 percent of the bearings have the potential to achieve the analytically predicted life of new bearings when one of the rings is replaced at rework. The potential savings from bearing rework varies from 53 to 82 percent of that of new bearings depending on the cost, size, and complexity of the bearing

Armed rollers: does nestling's vomit function as a defence against predators?

Directory of Open Access Journals (Sweden)

Deseada Parejo

Full Text Available Chemical defences against predators are widespread in the animal kingdom although have been seldom reported in birds. Here, we investigate the possibility that the orange liquid that nestlings of an insectivorous bird, the Eurasian roller (Coracias garrulus, expel when scared at their nests acts as a chemical defence against predators. We studied the diet of nestling rollers and vomit origin, its chemical composition and deterrent effect on a mammal generalist predator. We also hypothesized that nestling rollers, as their main prey (i.e. grasshoppers do from plants, could sequester chemicals from their prey for their use. Grasshoppers, that also regurgitate when facing to a threat, store the harmful substances used by plants to defend themselves against herbivores. We found that nestling rollers only vomit after being grasped and moved. The production of vomit depended on food consumption and the vomit contained two deterrent chemicals (hydroxycinnamic and hydroxybenzoic acids stored by grasshoppers and used by plants to diminish herbivory, suggesting that they originate from the rollers' prey. Finally, we showed for the first time that the oral secretion of a vertebrate had a deterrent effect on a model predator because vomit of nestling rollers made meat distasteful to dogs. These results support the idea that the vomit of nestling rollers is a chemical defence against predators.

Mechanical design problems associated with turbopump fluid film bearings

Science.gov (United States)

Evces, Charles R.

1990-01-01

Most high speed cryogenic turbopumps for liquid propulsion rocket engines currently use ball or roller contact bearings for rotor support. The operating speeds, loads, clearances, and environments of these pumps combine to make bearing wear a limiting factor on turbopump life. An example is the high pressure oxygen turbopump (HPOTP) used in the Space Shuttle Main Engine (SSME). Although the HPOTP design life is 27,000 seconds at 30,000 rpms, or approximately 50 missions, bearings must currently be replaced after 2 missions. One solution to the bearing wear problem in the HPOTP, as well as in future turbopump designs, is the utilization of fluid film bearings in lieu of continuous contact bearings. Hydrostatic, hydrodynamic, and damping seal bearings are all replacement candidates for contact bearings in rocket engine high speed turbomachinery. These three types of fluid film bearings have different operating characteristics, but they share a common set of mechanical design opportunities and difficulties. Results of research to define some of the mechanical design issues are given. Problems considered include transient strat/stop rub, non-operational rotor support, bearing wear inspection and measurement, and bearing fluid supply route. Emphasis is given to the HPOTP preburner pump (PBP) bearing, but the results are pertinent to high-speed cryogenic turbomachinery in general.

Gearbox Reliability Collaborative High Speed Shaft Tapered Roller Bearing Calibration

Energy Technology Data Exchange (ETDEWEB)

Keller, J.; Guo, Y.; McNiff, B.

2013-10-01

The National Renewable Energy Laboratory (NREL) Gearbox Reliability Collaborative (GRC) is a project investigating gearbox reliability primarily through testing and modeling. Previous dynamometer testing focused upon acquiring measurements in the planetary section of the test gearbox. Prior to these tests, the strain gages installed on the planetary bearings were calibrated in a load frame.

A Methodology of Designing the Teeth Conjugation in a Planetary Roller Screw

Directory of Open Access Journals (Sweden)

Lisowski Filip

2016-12-01

Full Text Available The paper presents the methodology for designing the teeth conjunction of planetary gears in the planetary roller screw mechanism. A function of the planetary gears is to synchronize an operation of rollers in order to avoid axial displacements. A condition of the correct operation is no axial movement of rollers in relation to the nut. The planetary gears are integral parts of rollers and therefore an operation of the gear transmissions has a direct impact on cooperation of the screw, rollers and the nut. The proper design of gear engagements is essential for reducing slippage on surfaces of the cooperating threaded elements. For this purpose, in a designing method, both the limitations of operation and kinematic conditions of rollers’ operation have to be taken into account.

Skateboarding: more dangerous than roller skating or in-line skating.

Science.gov (United States)

Osberg, J S; Schneps, S E; Di Scala, C; Li, G

1998-10-01

To describe the circumstances, severity, and outcomes of skating-related injuries among children admitted to trauma centers. A cross-sectional comparison of roller skaters (n = 154), in-line skaters (n = 190), and skateboarders (n = 254) aged 5 to 19 years who were hospitalized with injuries. Seventy-nine hospitals and pediatric trauma centers participating in the National Pediatric Trauma Registry between October 1988 and April 1997. Three quarters (75.8%) of the study sample were male, nearly half (47.8%) were injured on roads, and more than one third (37.1%) had head injuries. Among skateboarders, 50.8% had head injuries compared with 33.7% of in-line skaters and 18.8% of roller skaters (Pskateboarders were 8 times more likely to be severe or critical compared with roller skaters' injuries and more than 2 times as likely to be severe or critical compared with in-line skaters' injuries. Mean hospital length of stay was 6.0 days for skateboarders, 3.4 days for in-line skaters, and 2.4 days for roller skaters (PSkateboarders were more likely to be male and to be injured on roads than were in-line skaters or roller skaters. Skateboarding-related injuries are more severe and have more serious consequences than roller skating or in-line skating injuries. Research is needed to identify ergonomic and behavioral factors responsible for higher head injury risk to skateboarders, and interventions are needed to reduce the risk.

Natural roller bearing fault detection by angular measurement of true instantaneous angular speed

Science.gov (United States)

Renaudin, L.; Bonnardot, F.; Musy, O.; Doray, J. B.; Rémond, D.

2010-10-01

The challenge in many production activities involving large mechanical devices like power transmissions consists in reducing the machine downtime, in managing repairs and in improving operating time. Most online monitoring systems are based on conventional vibration measurement devices for gear transmissions or bearings in mechanical components. In this paper, we propose an alternative way of bearing condition monitoring based on the instantaneous angular speed measurement. By the help of a large experimental investigation on two different applications, we prove that localized faults like pitting in bearing generate small angular speed fluctuations which are measurable with optical or magnetic encoders. We also emphasize the benefits of measuring instantaneous angular speed with the pulse timing method through an implicit angular sampling which ensures insensitivity to speed fluctuation. A wide range of operating conditions have been tested for the two applications with varying speed, load, external excitations, gear ratio, etc. The tests performed on an automotive gearbox or on actual operating vehicle wheels also establish the robustness of the proposed methodology. By the means of a conventional Fourier transform, angular frequency channels kinematically related to the fault periodicity show significant magnitude differences related to the damage severity. Sideband effects are evidently seen when the fault is located on rotating parts of the bearing due to load modulation. Additionally, slip effects are also suspected to be at the origin of enlargement of spectrum peaks in the case of double row bearings loaded in a pure radial direction.

Pediatric fractures during skateboarding, roller skating, and scooter riding.

Science.gov (United States)

Zalavras, Charalampos; Nikolopoulou, Georgia; Essin, Daniel; Manjra, Nahid; Zionts, Lewis E

2005-04-01

Skateboarding, roller skating, and scooter riding are popular recreational and sporting activities for children and adolescents but can be associated with skeletal injury. The purpose of this study is to describe the frequency and characteristics of fractures resulting from these activities. Fractures from skateboarding, roller skating, and scooter riding compose a considerable proportion of pediatric musculoskeletal injuries. Case series; Level of evidence, 4. Demographic data and injury characteristics were analyzed for all patients who presented to the pediatric fracture clinic of the level I trauma center from January 2001 to May 2002 after sustaining fractures due to skateboarding, roller skating, and scooter riding. Among a total of 2371 fractures, the authors identified 325 fractures (13.7%) that occurred during one of these activities. There were 187 patients (mean age, 13 years; 95% male) who sustained 191 skateboard-related fractures, 64 patients (mean age, 10.8 years; 54% male) who sustained 65 fractures while roller skating, and 66 patients (mean age, 9.7 years; 64% male) who sustained 69 fractures while riding a scooter. The forearm was fractured most often, composing 48.2% of skate-boarding fractures, 63.1% of roller-skating fractures, and 50.7% of fractures due to scooter riding. Of the forearm fractures, 94% were located in the distal third. In the skateboarding group, 10 of 191 (5.2%) fractures were open injuries of the forearm, compared to 6 of 2046 (0.3%) fractures caused by other mechanisms of injury (significant odds ratio, 18.8). Skateboarding, roller-skating, and scooter-riding accidents result in a large proportion of pediatric fractures. An open fracture, especially of the forearm, was more likely to be caused by skateboarding than by other mechanisms of injury. Use of wrist and forearm protective equipment should be considered in all children who ride a skateboard.

Adaptive Spindle Balancing Using Magnetically Levitated Bearings

International Nuclear Information System (INIS)

BARNEY, PATRICK S.; LAUFFER, JAMES P.; PETTEYS, REBECCA; REDMOND, JAMES M.; SULLIVAN, WILLIAM N.

1999-01-01

A technological break through for supporting rotating shafts is the active magnetic bearing (AMB). Active magnetic bearings offer some important advantages over conventional ball, roller or journal bearings such as reduced frictional drag, no physical contact in the bearing, no need for lubricants, compatibility with high vacuum and ultra-clean environments, and ability to control shaft position within the bearing. The disadvantages of the AMB system are the increased cost and complexity, reduced bearing stiffness and the need for a controller. Still, there are certain applications, such as high speed machining, biomedical devices, and gyroscopes, where the additional cost of an AMB system can be justified. The inherent actuator capabilities of the AMB offer the potential for active balancing of spindles and micro-shaping capabilities for machine tools, The work presented in this paper concentrates on an AMB test program that utilizes the actuator capability to dynamically balance a spindle. In this study, an unbalanced AMB spindle system was enhanced with an LMS (Least Mean Squares) algorithm combined with an existing PID (proportional, integral, differential) control. This enhanced controller significantly improved the concentricity of an intentionally unbalanced shaft. The study included dynamic system analysis, test validation, control design and simulation, as well as experimental implementation using a digital LMS controller

Standard test method for measurement of web/roller friction characteristics

CERN Document Server

American Society for Testing and Materials. Philadelphia

2003-01-01

1.1 This test method covers the simulation of a roller/web transport tribosystem and the measurement of the static and kinetic coefficient of friction of the web/roller couple when sliding occurs between the two. The objective of this test method is to provide users with web/roller friction information that can be used for process control, design calculations, and for any other function where web/roller friction needs to be known. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Improving feeding powder distribution to the compaction zone in the roller compaction.

Science.gov (United States)

Yu, Mingzhe; Omar, Chalak; Schmidt, Alexander; Litster, James D; Salman, Agba D

2018-07-01

In the roller compaction process, powder flow properties have a significant influence on the uniformity of the ribbon properties. The objective of this work was to improve the powder flow in the feeding zone by developing novel feeding guiders which are located in the feeding zone close to the rollers in the roller compactor (side sealing system). Three novel feeding guiders were designed by 3D printing and used in the roller compactor, aiming to control the amount of powder passing across the roller width. The new feeding guiders were used to guide more powder to the sides between the rollers and less powder to the centre comparing to the original feeding elements. Temperature profile and porosity across the ribbon width indicated the uniformity of the ribbon properties. Using the novel feeding guiders resulted in producing ribbons with uniform temperature profile and porosity distribution across the ribbon width. The design of the feeding guiders contributed to improving the tensile strength of the ribbons produced from the compaction stage as well as reducing the fines produced from the crushing stage. Copyright © 2018 Elsevier B.V. All rights reserved.

A roller chain drive model including contact with guide-bars

DEFF Research Database (Denmark)

Pedersen, Sine Leergaard; Hansen, John Michael; Ambrósio, J. A. C.

2004-01-01

A model of a roller chain drive is developed and applied to the simulation and analysis of roller chain drives of large marine diesel engines. The model includes the impact with guide-bars that are the motion delimiter components on the chain strands between the sprockets. The main components...... and the sprocket centre, i.e. a constraint is added when such distance is less than the pitch radius. The unilateral kinematic constraint is removed when its associated constraint reaction force, applied on the roller, is in the direction of the root of the sprocket teeth. In order to improve the numerical...

On the bi-dimensional variational decomposition applied to nonstationary vibration signals for rolling bearing crack detection in coal cutters

International Nuclear Information System (INIS)

Jiang, Yu; Li, Zhixiong; Zhang, Chao; Peng, Z; Hu, Chao

2016-01-01

This work aims to detect rolling bearing cracks using a variational approach. An original method that appropriately incorporates bi-dimensional variational mode decomposition (BVMD) into discriminant diffusion maps (DDM) is proposed to analyze the nonstationary vibration signals recorded from the cracked rolling bearings in coal cutters. The advantage of this variational decomposition based diffusion map (VDDM) method in comparison to the current DDM is that the intrinsic vibration mode of the crack can be filtered into a limited bandwidth in the frequency domain with an estimated central frequency, thus discarding the interference signal components in the vibration signals and significantly improving the crack detection performance. In addition, the VDDM is able to simultaneously process two-channel sensor signals to reduce information leakage. Experimental validation using rolling bearing crack vibration signals demonstrates that the VDDM separated the raw signals into four intrinsic modes, including one roller vibration mode, one roller cage vibration mode, one inner race vibration mode, and one outer race vibration mode. Hence, reliable fault features were extracted from the outer race vibration mode, and satisfactory crack identification performance was achieved. The comparison between the proposed VDDM and existing approaches indicated that the VDDM method was more efficient and reliable for crack detection in coal cutter rolling bearings. As an effective catalyst for rolling bearing crack detection, this newly proposed method is useful for practical applications. (paper)

Phylogenetic relationships of rollers (Coraciidae) based on complete mitochondrial genomes and fifteen nuclear genes.

Science.gov (United States)

Johansson, Ulf S; Irestedt, Martin; Qu, Yanhua; Ericson, Per G P

2018-04-06

The rollers (Coraciidae) constitute a relative small avian family with ca. 12 species distributed in Africa, western and southern Eurasia, and eastern Australia. In this study we examine the phylogenetic relationships of all species currently recognized in the family, including two taxa whose taxonomic status is currently contested. By using shotgun sequencing on degraded DNA from museum study skins we have been able to recover complete mitochondrial genomes as well as 15 nuclear genes for in total 16 taxa. The gene sequences were analyzed both concatenated in a maximum likelihood framework as well in a species tree approach using MP-EST. The different analytical approaches yield similar, highly supported trees and support the current division of the rollers into two genera, Coracias and Eurystomus. The only conflict relates to the placement of the Blue-bellied Roller (C. cyanogaster), where the mitochondrial, and the concatenated nuclear and mitochondrial data set, place this taxon as sister to the other Coracias species, whereas nuclear data and the species tree analysis place it as the sister taxon of C. naevia and C. spatulatus. All analyses place the Eurasian roller (C. garrulus) with the two African species, Abyssinian Roller (C. abyssinica) and Liliac-breasted Roller (C. caudatus), and place this clade as the sister group to the Asian Coracias rollers. In addition, our results support a sister group relationship between the morphologically rather dissimilar Purple Roller (C. naevia) and Racquet-tailed Roller (C. spatulatus) and also support the division of Eurystomus in an African and an Asian clade. However, within the Asian clade the Azure Roller (E. azureus) from Halmahera appears to be nested within the Dollarbird (E. orientalis), indicating that that this taxon is a morphological divergent, but a rather recent offshoot, of the widespread Dollarbird. Similarly, the Purple-winged Roller (C. temminickii) from Sulawesi group together with C. benghalensis

Self-Controlling Rig for Jaw Crusher Assembly

OpenAIRE

Saurabh Jadhav; Anup Pawar

2017-01-01

The aim of the work is to develop a method for easy assembly of the bearing in the housing by standardized way. The assembly of bearing should take place on the atomized set up. Based on this method a assembly setup was constructed which enables to assembly of the shaft with bearing of different models of jaw crusher. First tests were done with manual alignment and it shows that with proper alignment shaft assembly is very easy operation and also safe. Results of those tests show that the dev...

SHABERTH - ANALYSIS OF A SHAFT BEARING SYSTEM (CRAY VERSION)

Science.gov (United States)

Coe, H. H.

1994-01-01

The SHABERTH computer program was developed to predict operating characteristics of bearings in a multibearing load support system. Lubricated and non-lubricated bearings can be modeled. SHABERTH calculates the loads, torques, temperatures, and fatigue life for ball and/or roller bearings on a single shaft. The program also allows for an analysis of the system reaction to the termination of lubricant supply to the bearings and other lubricated mechanical elements. SHABERTH has proven to be a valuable tool in the design and analysis of shaft bearing systems. The SHABERTH program is structured with four nested calculation schemes. The thermal scheme performs steady state and transient temperature calculations which predict system temperatures for a given operating state. The bearing dimensional equilibrium scheme uses the bearing temperatures, predicted by the temperature mapping subprograms, and the rolling element raceway load distribution, predicted by the bearing subprogram, to calculate bearing diametral clearance for a given operating state. The shaft-bearing system load equilibrium scheme calculates bearing inner ring positions relative to the respective outer rings such that the external loading applied to the shaft is brought into equilibrium by the rolling element loads which develop at each bearing inner ring for a given operating state. The bearing rolling element and cage load equilibrium scheme calculates the rolling element and cage equilibrium positions and rotational speeds based on the relative inner-outer ring positions, inertia effects, and friction conditions. The ball bearing subprograms in the current SHABERTH program have several model enhancements over similar programs. These enhancements include an elastohydrodynamic (EHD) film thickness model that accounts for thermal heating in the contact area and lubricant film starvation; a new model for traction combined with an asperity load sharing model; a model for the hydrodynamic rolling and

The thermodynamic properties of a new type catcher bearing used in active magnetic bearings system

International Nuclear Information System (INIS)

Jin, Chaowu; Zhu, Yili; Xu, Longxiang; Xu, Yuanping; Zheng, Yantong

2015-01-01

Normally a rotor levitated by active magnetic bearings (AMBs) system would rotate without contacting with any stator component, but the possibility still remains that the supporting force might lose temporarily or permanently, thus requiring the Catcher bearings (CBs) to provide backup protection in case of the failure of AMBs. A new type CB with two separate rolling element bearing series could have the speed distribution between the inner race and intermediate race according to certain ratio, in which the speed of each roller element bearing decreases with the limit speed of the whole CB increasing, offering high capability to sustain its initial rotation speed. Based on the theory of heat transfer, tribology, and rotor dynamics, this paper analyzes the thermal structure of double-decker catcher bearing (DDCB) and single-decker catcher bearing (SDCB), respectively. Through this structure, the thermal resistances and equations of heat transfer can be obtained. Then we calculate the friction heat and temperature distribution in the various CBs upon rotor's dropping on SDCB or DDCB, followed by the discussion on the CBs temperature rise's effects on lubrication conditions and rotor dynamics parameters. Finally various experiments are carried out to measure the temperature rise of different CBs. The results obtained validate the theoretical analysis and also provide main methods to reduce heat generation. Using DDCB is proved to be effective to reduce the temperature rise. - Highlights: • The DDCB is a more suitable catcher bearing for AMBs. • Compared to SDCB, using DDCB, the temperature rise can decrease in the same states. • A lower viscosity of lubricant may induce a lower temperature rise. • The inner raceway temperature of the first layer bearing is the highest. • Reducing the unbalance mass of the rotor is a method to decrease the temperature rise

Bearing Assembly With Carbonate Resistant Anti-Seizing Properties

Science.gov (United States)

2014-01-28

surface. Dkt . No. 101805 Application No. ?? REPLACEMENT SHEET? /21 LINEAR MOVEMENT ROTATIONAL MOVEMENT BEARING SURFACE ROTOR OR SLIDER BEARING ROTOR...OR SLIDER BEARING SHAFT FIG. 1 (PRIOR ART) FIG. 2 (PRIOR ART) Dkt . No. 101805 Application No. ?? REPLACEMENT SHEET? /22 100 110 112 114 120 118 116 120 118 114 112 110 LINEAR MOVEMENT ROTATIONAL MOVEMENT 100 FIG. 3 FIG. 4

Rotating head for air, gas and mud drilling

Energy Technology Data Exchange (ETDEWEB)

Pruitt, A.B.

1983-05-17

A rotating head assembly having roller thrust bearings rotatably journaling an inner barrel is provided with pump means for continuous forced circulation of lubricating oil to, and around, the thrust bearings during operation. A lubricating oil chamber substantially surrounds the bearings, which chamber is effectively sealed against leakage of oil fluids, and other debris, into the chamber and lubricating oil out of the chamber. The lower end of the rotatably journaled inner barrel is provided with a stripper rubber structured to enable use of the head with drill pipe of diverse outer diameters.

Ni-Ti Next Generation Bearings for Space Applications

Science.gov (United States)

DellaCorte, Christopher

2018-01-01

NASA applications challenge traditional bearing materials. The rigors of launch often include heavy shock loads and exposure to corrosive environments (e.g., salt spray). Unfortunately, ball and roller bearings made from hardened steels are vulnerable to Brinell denting and rust which can limit performance and life. Ceramic materials can eliminate corrosion concerns but their high stiffness and extreme hardness actually makes denting problems worse. In this presentation, an emerging superelastic alloy, NiTi, is introduced for rolling element bearing applications. Through a decade of RD, NiTi alloy bearings have been put through a comprehensive series of life and performance tests. Hardness, corrosion, strength, stiffness, and rolling contact fatigue tests have been conducted and reported. Ball bearings ranging in size from 12 to 50mm bore have been successfully engineered and operated over a wide range of speeds and test conditions including being submerged in water. The combination of high hardness, moderate elastic modulus, low density, and intrinsic corrosion immunity provide new possibilities for mechanisms that operate under extreme conditions. Recent preliminary tests indicate that bearings can be made from NiTi alloys that are easily lubricated by conventional oils and greases and exhibit acceptable rolling contact fatigue resistance. This presentation introduces the NiTi materials systems and shows how NASA is using it to alleviate several specific problems encountered in advanced space applications.

Comparison of Different Assembling Techniques Regarding Cost, Durability, and Ecology - A Survey of Multi-layer Wooden Panel Assembly Load-Bearing Construction Elements

Directory of Open Access Journals (Sweden)

Dietrich Buck

2015-10-01

Full Text Available Wood is a pure, sustainable, renewable material. The increasing use of wood for construction can improve its sustainability. There are various techniques to assemble multi-layer wooden panels into prefabricated, load-bearing construction elements. However, comparative market and economy studies are still scarce. In this study, the following assembling techniques were compared: laminating, nailing, stapling, screwing, stress laminating, doweling, dovetailing, and wood welding. The production costs, durability, and ecological considerations were presented. This study was based on reviews of published works and information gathered from 27 leading wood product manufacturing companies in six European countries. The study shows that the various techniques of assembling multi-layer wooden construction panel elements are very different. Cross laminated timber (CLT exhibited the best results in terms of cost and durability. With regard to ecological concerns, dovetailing is the best. Taking into account both durability and ecological considerations, wooden screw-doweling is the best. These alternatives give manufacturers some freedom of choice regarding the visibility of surfaces and the efficient use of lower-quality timber. CLT is the most cost-effective, is not patented, and is a well-established option on the market today.

Edgewise vibration control of wind turbine blades using roller and liquid dampers

DEFF Research Database (Denmark)

Zhang, Zili; Nielsen, Søren R.K.

2014-01-01

suppressing edgewise vibrations. The roller dampers are more volumetrically efficient due to the higher mass density of the steel comparing with the liquid. On the other hand, TLCDs have their advantage that it is easier to specify the optimum damping of the damper by changing the opening ratio of the orifice......This paper deals with the passive vibration control of edgewise vibrations by means of roller dampers and tuned liquid column dampers (TLCDs). For a rotating blade, the large centrifugal acceleration makes it possible to use roller dampers or TLCDs with rather small masses for effectively...

Edgewise vibration control of wind turbine blades using roller and liquid dampers

International Nuclear Information System (INIS)

Zhang, Z L; Nielsen, S R K

2014-01-01

This paper deals with the passive vibration control of edgewise vibrations by means of roller dampers and tuned liquid column dampers (TLCDs). For a rotating blade, the large centrifugal acceleration makes it possible to use roller dampers or TLCDs with rather small masses for effectively suppressing edgewise vibrations. The roller dampers are more volumetrically efficient due to the higher mass density of the steel comparing with the liquid. On the other hand, TLCDs have their advantage that it is easier to specify the optimum damping of the damper by changing the opening ratio of the orifice. In this paper, 2-DOF nonlinear models are suggested for tuning a roller damper or a TLCD attached to a rotating wind turbine blade, ignoring the coupling between the blade and the tower. The decoupled optimization is verified by incorporating the optimized damper into a more sophisticated 13- DOF wind turbine model with due consideration of the coupled blade-tower-drivetrain vibrations, quasi-static aeroelasticity as well as a collective pitch controller. Performances of the dampers are compared in terms of the control efficiency and the practical applications. The results indicate that roller dampers and TLCDs at optimal tuning can effectively suppress the dynamic response of wind turbine blades

Daylighting performance evaluation of a bottom-up motorized roller shade

Energy Technology Data Exchange (ETDEWEB)

Kapsis, K.; Athienitis, A.K.; Zmeureanu, R.G. [Department of Building, Civil and Environmental Engineering, Concordia University, Montreal, QC (Canada); Tzempelikos, A. [School of Civil Engineering, Purdue University, West Lafayette, IN (United States)

2010-12-15

This paper presents an experimental and simulation study for quantifying the daylighting performance of bottom-up roller shades installed in office spaces. The bottom-up shade is a motorized roller shade that opens from top to bottom operating in the opposite direction of a conventional roller shade, so as to cover the bottom part of the window, while allowing daylight to enter from the top part of the window, reaching deeper into the room. A daylighting simulation model, validated with full-scale experiments, was developed in order to establish correlations between the shade position, outdoor illuminance and work plane illuminance for different outdoor conditions. Then, a shading control algorithm was developed for application in any location and orientation. The validated model was employed for a sensitivity analysis of the impact of shade optical properties and control on the potential energy savings due to the use of daylighting. The results showed that Daylight Autonomy for the bottom-up shade is 8-58% higher compared to a conventional roller shade, with a difference of 46% further away from the facade, where the use of electric lighting is needed most of the time. The potential reduction in energy consumption for lighting is 21-41%. (author)

Study of hydrodynamic behaviour of large bearings depending on the viscosity of the lubricant

Directory of Open Access Journals (Sweden)

Barabas Sorin

2017-01-01

Full Text Available The research refers to study of hydrodynamic behavior of large bearings equipped with automatic lubrication system, where the liquid used may have a viscosity with variable values depending on the temperature or depending on the additive used. The introduction of additives with nanoparticles causes modification of viscosity and a significant reduction of friction coefficient. This study establishes a direct link between the friction, viscosity and tensions that occur in the contact area. Experimental studies confirm improving tribological properties of the contact area between the bearing rollers and raceways, through attracting nanoparticles on surfaces in contact and reducing friction coefficient. Accomplished finite element analysis showed decrease of the contact stresses, therefore decrease of the wear and increase the life of the bearing. Research has concluded that influencing viscosity and friction coefficient of lubricant can result in reducing wear of the bearing components, as well as increase the lifetime of bearing.

Increased Wear Resistance of Surfaces of Rotation Bearings Methods Strengthening-Smoothing Processing

Directory of Open Access Journals (Sweden)

A.A. Tkachuk

2016-05-01

Full Text Available Trends of modern engineering put forward higher requirements for quality bearings. This is especially true on production of bearings for special purposes with high speeds of rotation and resource. Much more opportunities in the technology management quality surface layers appear in the application of smoothing-strengthening methods, based on superficial plastic deformation. Working models of cutting lathes, grinders and tool smoothing sequence revealed the formation of operational parameters in the technological cycle of roller rings. The model of the dynamics of elastic deformation of the work piece tool helps identify actions radial force in the contact “surface – indenter.” Using mathematical modelling resolved a number of issues relevant process.

Off gas film cooler cleaner

Science.gov (United States)

Dhingra, Hardip S.; Koch, William C.; Burns, David C.

1997-01-01

An apparatus for cleaning depositions of particulate matter from the inside of tubular piping while the piping is in use. The apparatus is remote controlled in order to operate in hazardous environments. A housing containing brush and shaft assemblies is mounted on top of the tubular piping. Pneumatic cylinders provide linear motion. A roller nut bearing provides rotary motion. The combined motion causes the brush assembly to rotate as it travels along the tube dislodging particulate matter.

Roller compaction: Effect of relative humidity of lactose powder.

Science.gov (United States)

Omar, Chalak S; Dhenge, Ranjit M; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

2016-09-01

The effect of storage at different relative humidity conditions, for various types of lactose, on roller compaction behaviour was investigated. Three types of lactose were used in this study: anhydrous lactose (SuperTab21AN), spray dried lactose (SuperTab11SD) and α-lactose monohydrate 200M. These powders differ in their amorphous contents, due to different manufacturing processes. The powders were stored in a climatic chamber at different relative humidity values ranging from 10% to 80% RH. It was found that the roller compaction behaviour and ribbon properties were different for powders conditioned to different relative humidities. The amount of fines produced, which is undesirable in roller compaction, was found to be different at different relative humidity. The minimum amount of fines produced was found to be for powders conditioned at 20-40% RH. The maximum amount of fines was produced for powders conditioned at 80% RH. This was attributed to the decrease in powder flowability, as indicated by the flow function coefficient ffc and the angle of repose. Particle Image Velocimetry (PIV) was also applied to determine the velocity of primary particles during ribbon production, and it was found that the velocity of the powder during the roller compaction decreased with powders stored at high RH. This resulted in less powder being present in the compaction zone at the edges of the rollers, which resulted in ribbons with a smaller overall width. The relative humidity for the storage of powders has shown to have minimal effect on the ribbon tensile strength at low RH conditions (10-20%). The lowest tensile strength of ribbons produced from lactose 200M and SD was for powders conditioned at 80% RH, whereas, ribbons produced from lactose 21AN at the same condition of 80% RH showed the highest tensile strength. The storage RH range 20-40% was found to be an optimum condition for roll compacting three lactose powders, as it resulted in a minimum amount of fines in the

The System of Simulation and Multi-objective Optimization for the Roller Kiln

Science.gov (United States)

Huang, He; Chen, Xishen; Li, Wugang; Li, Zhuoqiu

It is somewhat a difficult researching problem, to get the building parameters of the ceramic roller kiln simulation model. A system integrated of evolutionary algorithms (PSO, DE and DEPSO) and computational fluid dynamics (CFD), is proposed to solve the problem. And the temperature field uniformity and the environment disruption are studied in this paper. With the help of the efficient parallel calculation, the ceramic roller kiln temperature field uniformity and the NOx emissions field have been researched in the system at the same time. A multi-objective optimization example of the industrial roller kiln proves that the system is of excellent parameter exploration capability.

Design, development and evaluation of a divergent roller sizer for almond kernels

Directory of Open Access Journals (Sweden)

D Ghanbarian

2015-09-01

Full Text Available Introduction: Iran is one of the major producers of almonds. According to the statistics released by FAO (2011, Iran with more than 110000 tons of almonds is the third in rank throughout the world. However, most Iranian almonds are presented as an unsorted and unpackaged product. Some producers sort their products by hand which is very time-consuming and labor-intensive. So, there is an essential need for suitable grading and packaging machines especially for the export of almond kernels.Grading, which is sometimes called sorting, is basically separating the material in different homogenous groups according to its specific characteristics like size, shape, color and on the basis of quality. Weighing is one of the best methods for grading agricultural products based on size, but due to its high cost and complexity of operations, usage of weigh size sorting machines is practically limited. So, sizing of most agricultural products is accomplished based on their dimensional attributes such as diameter, length, thickness or a combination of them. Field study shows that recently vibrating sizing machines are used for grading almond kernels. This type of sizing machine is huge, expensive, noisy and it consumes a lot of energy. Thus, the main objective of the present study was the design, development and evaluation of a new prototype of an almond kernel sizing machine. Materials and methods: It is important that the machine could resolve defects of existing vibrating machines. It should provide efficient and cost effective sizing for a wide range of kernel sizes and shapes. Furthermore, it should be of simple construction and be able to accept manual feeding. Previously conducted experiments showed that the thickness of the kernel is the most appropriate dimension for its sizing. Among the different types of dimensional sizing machines, the divergent roller grader which grades the products based on their thickness is considered to be one of the simplest

Roller Skating; Physical Education: 9.8414.

Science.gov (United States)

Amacker, Kathy; Mikell, Lenora

GRADES OR AGES: Grades 7-12. SUBJECT MATTER: Methods and procedures of roller skating. ORGANIZATION AND PHYSICAL APPEARANCE: The contents are divided into six areas, which are Course Guidelines, Course Description and Accreditation Standard Broad Goal, Course of Study Behavioral Objectives, Course Content, Learning Activities and Teaching…

Knee joint position sense of roller hockey players: a comparative study.

Science.gov (United States)

Venâncio, João; Lopes, Diogo; Lourenço, Joaquim; Ribeiro, Fernando

2016-06-01

This study aimed to compare knee joint position sense of roller hockey players with an age-matched group of non-athletes. Forty-three male participants voluntarily participated in this cross-sectional study: 21 roller hockey players (mean age: 23.2 ± 4.2 years old, mean weight: 81.8 ± 9.8 kg, mean height: 180.5 ± 4.1 cm) and 22 age-matched non-athletes (mean age: 23.7 ± 3.9 years old, mean weight: 85.0 ± 6.2 kg, mean height: 181.5 ± 5.0 cm). Knee joint position sense of the dominant limb was evaluated using a technique of open-kinetic chain and active knee positioning. Joint position sense was reported using absolute, relative and variable angular errors. The main results indicated that the group of roller hockey players showed significantly lower absolute (2.4 ± 1.2º vs. 6.5 ± 3.2º, p ≤ 0.001) and relative (1.7 ± 2.1º vs. 5.8 ± 4.4º, p ≤ 0.001) angular errors in comparison with the non-athletes group. In conclusion, the results from this present study suggest that proprioceptive acuity, assessed by measuring joint position sense, is increased in roller hockey players. The enhanced proprioception of the roller hockey players could contribute to injury prevention and improved performance during sporting activities.

Defect diagnosis and root cause analysis for thrust roller bearing of centrifugal charging pump

International Nuclear Information System (INIS)

Guo Yi

2012-01-01

The centrifugal charging pump is one of the most important equipment for Nuclear power plant which requires very high reliability, during C9 fuel-cycle, the continuous high level vibration alarm happened on the centrifugal charging pump B, we diagnosed its faults correctly and selected the right operation mode and right time to dismantle it which ensure the safety and economic benefits of Nuclear power plant, and through deeply analysis the root causes of thrust bearing defaults, we can learn much from it especially for the diagnosis and analysis to the bearing faults which is common for rotating equipment. (author)

Case histories of roller cone core bit application in crystalline rock

International Nuclear Information System (INIS)

Dahlem, J.S.

1988-01-01

The increased interest in deep crystalline rock drilling projects has resulted in a requirement for premium coring bits which are effective in such a harsh and abrasive environment. Hard formation roller cone insert bits have traditionally and constantly performed well in crystalline rock. As a result, the application of state of the art roller cone rock bit technology to the design and development of core bits has made crystalline coring projects more viable than ever before. This paper follows the development of roller cone core bits by examining their use on project such as HDR (Hot Dry Rock, Los Alamos); NAGRA (Nuclear Waste Disposal Wells in Switzerland); Camborne School of Mines Geothermal Project in Cornwall, UK; Deep Gas Project in Sweden; and the KTB Deep Drilling Project in West Germany

Dropping a particle out of a roller coaster

International Nuclear Information System (INIS)

Mungan, Carl E; Lipscombe, Trevor C

2014-01-01

A rider in a roller coaster lets go of a particle such as a small marble. How far does the marble travel horizontally from the point of release before hitting the ground, assuming the speed of the roller coaster is determined by conservation of mechanical energy starting from the highest hill up which it was pulled? Where should the marble be released along the track if one wishes to maximize the range of the marble? These questions constitute interesting variations on conventional problems in two-dimensional kinematics, appropriate for an undergraduate course in classical mechanics. Exploration of various shapes of tracks could form interesting student projects for numerical or experimental investigation. (paper)

3000-HP Roller Gear Transmission Development Program. Volume 3. Roller Gear Manufacture

Science.gov (United States)

1975-07-01

power is fed through the ramp roller clutch type free- wheel units to spur gears which mesh with the combining spur gear whose centerline is common...when the engine tends to turn faster than the main rotor shaft. It is in the free- wheel mode when the main rotor shaft tends to turn faster than the...gears are cut progrind at this time. Check face runout on each end of largo gears. Not to exceed .002" TIR 30 EBW one end 40 EBW opposite end

Temperature and Thermal Expansion Analysis of the Cooling Roller Based on the Variable Heat Flux Boundary Condition

Science.gov (United States)

Li, Yongkang; Yang, Yang; He, Changyan

2018-06-01

Planar flow casting (PFC) is a primary method for preparing an amorphous ribbon. The qualities of the amorphous ribbon are significantly influenced by the temperature and thermal expansion of the cooling roller. This study proposes a new approach to analyze the three-dimensional temperature and thermal expansion of the cooling roller using variable heat flux that acted on the cooling roller as a boundary condition. First, a simplified two-dimensional model of the PFC is developed to simulate the distribution of the heat flux in the circumferential direction with the software FLUENT. The resulting heat flux is extended to be three-dimensional in the ribbon's width direction. Then, the extended heat flux is imported as the boundary condition by the CFX Expression Language, and the transient temperature of the cooling roller is analyzed in the CFX software. Next, the transient thermal expansion of the cooling roller is simulated through the thermal-structural coupling method. Simulation results show that the roller's temperature and expansion are unevenly distributed, reach the peak value in the middle width direction, and the quasi-steady state of the maximum temperature and thermal expansion are achieved after approximately 50 s and 150 s of casting, respectively. The minimum values of the temperature and expansion are achieved when the roller has a thickness of 45 mm. Finally, the reliability of the approach proposed is verified by measuring the roller's thermal expansion on the spot. This study provides theoretical guidance for the roller's thermal expansion prediction and the gap adjustment in the PFC.

Modelling and simulation of dynamic wheel-rail interaction using a roller rig

International Nuclear Information System (INIS)

Anyakwo, A; Pislaru, C; Ball, A; Gu, F

2012-01-01

The interaction between the wheel and rail greatly influences the dynamic response of railway vehicles on the track. A roller rig facility can be used to study and monitor real time parameters that influence wheel-rail interaction such as wear, adhesion, friction and corrugation without actual field tests being carried out. This paper presents the development of the mathematical models for full scale roller rig and 1/5 scale roller rig and the wear prediction model based on KTH wear function. The simulated critical speed for the 1/5 scale roller rig is about one-fifth of the critical speed for the full scale model so the simulated results compare well with the theory related to wheel-rail contact and dynamics. Also the differences between the simulated rolling radii for the full scale model with and without wear function are analysed. This paper presents the initial stage of a large scale research project where the influence of wear on the wheel-rail performance will be studied in more depth.

Rock 'n roller coaster : an explorative study on the evolution of the European steel roller coaster industry

NARCIS (Netherlands)

Timmermans, B.; Bekkers, R.N.A.; Bordoli, L.

2012-01-01

This article investigates the 50 years evolution of the European steel roller coaster industry, which can be classified as a complex products systems (CoPS) industry. This industry is characterized as a non-shake out industry where entry can be divided in three waves, i.e. early diversifiers, new

Geometric modeling in the problem of ball bearing accuracy

Science.gov (United States)

Glukhov, V. I.; Pushkarev, V. V.; Khomchenko, V. G.

2017-06-01

The manufacturing quality of ball bearings is an urgent problem for machine-building industry. The aim of the research is to improve the geometric specifications accuracy of bearings based on evidence-based systematic approach and the method of adequate size, location and form deviations modeling of the rings and assembled ball bearings. The present work addressed the problem of bearing geometric specifications identification and the study of these specifications. The deviation from symmetric planar of rings and bearings assembly and mounting width are among these specifications. A systematic approach to geometric specifications values and ball bearings tolerances normalization in coordinate systems will improve the quality of bearings by optimizing and minimizing the number of specifications. The introduction of systematic approach to the international standards on rolling bearings is a guarantee of a significant increase in accuracy of bearings and the quality of products where they are applied.

Cost of a roller skating rink to the local accident and emergency department.

Science.gov (United States)

Nayeem, N; Shires, S E; Porter, J E

1990-01-01

A 14 month retrospective study was undertaken to determine the cost implications of the opening of a roller skating rink to the local hospital accident and emergency department (A and E). A total of 398 patients attended following injury at the roller skating rink, of whom 384 were included in the study. The estimated cost of their injuries was determined by the hospital accounts department. The average cost per patient attending the A and E department following roller skating injury was about 100 pounds. The total cost to the A and E department of all injuries sustained at the rink over this period was 38,412 pounds. The cost implications of opening a roller skating rink for the A and E department are considerable. If proposals for self-budgeting are applied, A and E departments will have to seek additional funding if such leisure facilities are opened in their vicinity. PMID:2097020

Influence of Surface-profile and Movement-path of Roller on Thickness Thinning during Multi-pass Deep Drawing Spinning

Directory of Open Access Journals (Sweden)

Xia Qinxiang

2016-01-01

Full Text Available Over thinning is a serious defect influencing the forming quality of spun workpiece during multi-pass deep drawing spinning. Surface-profile and movement-path of roller are the key factors influencing the thinning ratio of wall thickness of spun workpiece. The influence of surface-profile and movement-path of roller on thickness thinning were studied based on numerical simulation and experimental research, four groups of forming experiments were carried out under the combination of the different surface-profile of roller (R12 and R25-12 and movement-path of roller (spinning from the bottom of the blank and spinning from the middle of the blank. The results show that both the surface-profile and movement-path of roller have great influence on wall thickness thinning during multi-pass deep drawing spinning; and compared with the movement-path of roller, the influence of surface-profile of roller is more significant. The experimental results conform well to the simulation ones. It indicates that the FEA model established is reasonable and reliable.

Oriented Onion Sowing by a Forked-Roller Sowing Unit

Directory of Open Access Journals (Sweden)

Aleksandr G.

2018-03-01

Full Text Available Introduction: The existing sowing machines do not provide a single feeding of the bulbs with a planting (sowing unit that leads to a violation of the agrotechnical requirements of planting bulbs. It is necessary to search new solutions to preserve the position of the bulbs in the furrow with the bottom down and their regularly spaced distribution. Materials and Methods: The article presents the design for a prototype for a planting machine equipped with a forked-roller sowing unit for orienting the onion-sowing into a furrow. Testing the forked-roller sowing unit were carried out on a flat area where the physical and mechanical properties of the soil were determined on the days of sowing, and the indices of the quality of the onion-sowing were determined. The study of the effect of the sowing machine speed on the quality of the onion-seed bulb landing was determined by the change in the translational speed of the sowing unit in the range of 0.8 m/s to 1.2 m/s with a variation interval of 0.1 m/s. The indicators of the quality of the planting of the bulbs were determined by the opening of the closed furrow. The results of laboratory-field studies of the planting machine prototype are presented. Results: The results of laboratory-field studies of a planting machine equipped with a forked-roller sowing unit for planting onion bulbs are presented. The optimal technological parameters are determined experimentally. It was determined the number of bulbs that are for up is 51 % and the regularity of planting by the forked-roller sowing unit – 79 %. These figures are provided at the forward speed of the planting machine VM = 0.9–1.0 m/s, the height of the fall of the bulb HA = 0.12 m, and the rotation frequency of the landing drum nБ = 0.47 c-1. Discussion and Conclusions: The use of a forked-roller sowing unit makes it possible to increase the proportion of onions planted by bottom down by 200 %, and the uniformity of planting bulbs by 19 %, in

Recalibrated Equations for Determining Effect of Oil Filtration on Rolling Bearing Life

Science.gov (United States)

Needelman, William M.; Zaretsky, Erwin V.

2014-01-01

In 1991, Needelman and Zaretsky presented a set of empirically derived equations for bearing fatigue life (adjustment) factors (LFs) as a function of oil filter ratings. These equations for life factors were incorporated into the reference book, "STLE Life Factors for Rolling Bearings." These equations were normalized (LF = 1) to a 10-micrometer filter rating at Beta(sub x) = 200 (normal cleanliness) as it was then defined. Over the past 20 years, these life factors based on oil filtration have been used in conjunction with ANSI/ABMA standards and bearing computer codes to predict rolling bearing life. Also, additional experimental studies have been made by other investigators into the relationship between rolling bearing life and the size, number, and type of particle contamination. During this time period filter ratings have also been revised and improved, and they now use particle counting calibrated to a new National Institute of Standards and Technology (NIST) reference material, NIST SRM 2806, 1997. This paper reviews the relevant bearing life studies and describes the new filter ratings. New filter ratings, Beta(sub x(c)) = 200 and Beta(sub x(c)) = 1000, are benchmarked to old filter ratings, Beta(sub x) = 200, and vice versa. Two separate sets of filter LF values were derived based on the new filter ratings for roller bearings and ball bearings, respectively. Filter LFs can be calculated for the new filter ratings.

Verkkokaupan kansainvälistäminen Facebook-mainonnalla : Case HighRoller

OpenAIRE

Heikkinen, Tiia

2016-01-01

Verkkokauppa toimii HighRoller Suomi Oy:n HighRoller-lihashuoltolaiteen pääasiallisena myyntikanavana ja Facebook-markkinointikanavana. Tähän mennessä tuotetta on markkinoitu Facebookissa ilman varsinaista strategiaa. Nyt tuotetta viedään Ruotsiin ja uusia markkinoita varten suunniteltiin ja toteutettiin Facebook-mainoskampanja. Teoreettisessä viitekehyksessä käydään läpi aluksi digimarkkinointia, minkä jälkeen pohditaan sosiaalisen median merkitystä verkkokaupalle. Seuraavaksi keskitytää...

An investigation into the impact of magnesium stearate on powder feeding during roller compaction.

Science.gov (United States)

Dawes, Jason; Gamble, John F; Greenwood, Richard; Robbins, Phil; Tobyn, Mike

2012-01-01

A systematic evaluation on the effect of magnesium stearate on the transmission of a placebo formulation from the hopper to the rolls during screw fed roller compaction has been carried out. It is demonstrated that, for a system with two 'knurled' rollers, addition of 0.5% w/w magnesium stearate can lead to a significant increase in ribbon mass throughput, with a consequential increase in roll gap, compared to an unlubricated formulation (manufactured at equivalent process conditions). However, this effect is reduced if one of the rollers is smooth. Roller compaction of a lubricated formulation using two smooth rollers was found to be ineffective due to a reduction in friction at the powder/roll interface, i.e. powder was not drawn through the rollers leading to a blockage in the feeding system. An increase in ribbon mass throughput could also be achieved if the equipment surfaces were pre-lubricated. However this increase was found to be temporary suggesting that the residual magnesium stearate layer was removed from the equipment surfaces. Powder sticking to the equipment surfaces, which is common during pharmaceutical manufacturing, was prevented if magnesium stearate was present either in the blend, or at the roll surface. It is further demonstrated that the influence of the hopper stirrer, which is primarily used to prevent bridge formation in the hopper and help draw powder more evenly into the auger chamber, can lead to further mixing of the formulation, and could therefore affect a change in the lubricity of the carefully blended input material.

Design rules for out-of-plane stability of roller bent steel arches with FEM

NARCIS (Netherlands)

Spoorenberg, R.C.; Snijder, H.H.; Hoenderkamp, J.C.D.; Beg, D.

2012-01-01

This paper describes a numerical investigation into the out-of-plane buckling behavior of freestanding roller bent steel arches. As roller bent arches have structural imperfections which differ considerably from those of hot-rolled or welded sections, specific attention is paid to their inclusion in

Magnetic bearings for free-piston Stirling engines

Science.gov (United States)

Curwen, P. W.; Fleming, D. P.; Rao, D. K.; Wilson, D. S.

1992-01-01

The feasibility and efficacy of applying magnetic bearings to free-piston Stirling-cycle power conversion machinery currently being developed for long-term space missions are assessed. The study was performed for a 50-kWe Reference Stirling Space Power Converter (RSSPC) which currently uses hydrostatic gas bearings to support the reciprocating displacer and power piston assemblies. Active magnetic bearings of the attractive electromagnetic type are feasible for the RSSPC power piston. Magnetic support of the displacer assembly would require unacceptable changes to the design of the current RSSPC. However, magnetic suspension of both displacer and power piston is feasible for a relative-displacer version of the RSSPC. Magnetic suspension of the RSSPC power piston can potentially increase overall efficiency by 0.5 to 1 percent (0.1 to 0.3 efficiency points). Magnetic bearings will also overcome several operational concerns associated with hydrostatic gas bearing systems. These advantages, however, are accompanied by a 5 percent increase in specific mass of the RSSPC.

Application research of ferrous matrix composites in roller ring used in high-speed wire/bar rolling mill

International Nuclear Information System (INIS)

Song Yanpei; Li Xiuqing; Bi Shuangxu

2010-01-01

Research highlights: → A composite structure roller rings was fabricated by centrifugal casting. → The roller rings consisted of outer WCP/Fe-C composites layer and inner Fe-C alloy matrix. → Hardness attained to HRA80-85 in the composites layer, and HRA73-76 in inner Fe-C alloy matrix where the toughness was over 8 J/cm 2 . → The wear resistance of the roller rings excelled that of high-speed steel, and approached to that of the WC hard alloy roll. → The production cost of the WCP/Fe-C composites roller ring decreased by 50%. - Abstract: Tungsten carbide particle (WC P ) reinforced ferrous matrix composites roller rings were fabricated by centrifugal casting. The microstructures, properties and application effect of the composites roller rings were investigated by SEM, TEM and various property testers. The experimental results show that the WC P were uniformly distributed in outer reinforced-layer (working-layer) of 20-50 mm in thickness and their volume fraction reached 60-80 vol.%; there was a good interface bonding between WC P and Fe-C alloy without any reaction products; hardness attained to HRA80-85 in working-layer, and HRA73-76 in inner ferrous matrix where the toughness was over 8 J/cm 2 ; the wear resistance of the composites roller rings excels that of high-speed steel; service life of the composites parts approached to that of the WC hard alloy roll when the same WC P -volume-fraction in working-layer were obtained for both of them, but the production cost of the WC P /Fe-C composites roller ring decreased by 50%.

Molecular phylogeny and SNP variation of polar bears (Ursus maritimus), brown bears (U. arctos), and black bears (U. americanus) derived from genome sequences.

Science.gov (United States)

Cronin, Matthew A; Rincon, Gonzalo; Meredith, Robert W; MacNeil, Michael D; Islas-Trejo, Alma; Cánovas, Angela; Medrano, Juan F

2014-01-01

We assessed the relationships of polar bears (Ursus maritimus), brown bears (U. arctos), and black bears (U. americanus) with high throughput genomic sequencing data with an average coverage of 25× for each species. A total of 1.4 billion 100-bp paired-end reads were assembled using the polar bear and annotated giant panda (Ailuropoda melanoleuca) genome sequences as references. We identified 13.8 million single nucleotide polymorphisms (SNP) in the 3 species aligned to the polar bear genome. These data indicate that polar bears and brown bears share more SNP with each other than either does with black bears. Concatenation and coalescence-based analysis of consensus sequences of approximately 1 million base pairs of ultraconserved elements in the nuclear genome resulted in a phylogeny with black bears as the sister group to brown and polar bears, and all brown bears are in a separate clade from polar bears. Genotypes for 162 SNP loci of 336 bears from Alaska and Montana showed that the species are genetically differentiated and there is geographic population structure of brown and black bears but not polar bears.

Roller pressure algometry as a new tool for assessing dynamic pressure sensitivity in migraine

DEFF Research Database (Denmark)

Guerrero-Peral, Ángel L.; Ruíz, Marina; Barón, Johanna

2018-01-01

from 500 to 5300 g. Each roller was moved at a speed of 0.5 cm/sec over a 60 mm horizontal line covering the temporalis muscle. The dynamic pain threshold (the pressure level of the first painful roller) and pain elicited during the pain threshold (roller evoked pain) were determined. Static pressure...... pain thresholds were assessed over the temporalis muscle, C5/C6 joint, second metacarpal, and tibialis anterior. Results Side-to-side consistency between dynamic pain threshold (rs = 0.769, p ... was slightly stronger in chronic migraine. Pain during dynamic pain threshold was negatively associated with widespread pressure pain thresholds (-0.336 

Sandvik's HM 150 roller in action on the world's largest conveyor bridge in the Lusatia region; Sandvik HM 150 auf der weltgroessten Foerderbruecke in der Lausitz im Einsatz

Energy Technology Data Exchange (ETDEWEB)

Waliczek, Sven; Raddatz, Ulrich [Sandvik Mining and Construction Central Europe GmbH, Essen (Germany)

2010-09-15

Prince Herrmann Ludwig Heinrich von Pueckler-Muskau, a landscape gardening genius, built the Muskau Park in the Lusatia region in 1817 - it is part of a UNESCO world heritage site today. In the same era, 1850, the first lignite was mined in the region and still today, Vattenfall, the Swedish company, extracts lignite without subsidies - in Jaenschwalde among other places, one out of the five opencast mines currently in operation. As one of the largest employers and apprenticing companies in East Germany, Vattenfall currently employs almost 8000 employees and about 800 apprentices. Sandvik Mining and Construction also plays a leading role - in the literal sense. At the Jaenschwalde location there are 320 sets of 5-roller garlands of HM150 formed rollers in action on the overburden conveyor bridge AFB 60m (Figure 1) - on belt five, the main belt conveyor (belt type 3000 ST3000-18:8, idler spacing approx. 800 mm) and on belt eight, the stockpile belt conveyor (belt type 2750 ST2500-18:8, idler spacing approx. 800 mm). It all began in the spring of 2004. Bernhard Hofmayer, Production Manager at Sandvik, introduced the HM150 formed roller to Vattenfall. The engineers were impressed by the completely new design and the innovative assembly technique. The discussion about the advantages and disadvantages of the component optimised formed roller were ready to begin. (orig.)

Effect of Using Porcelanite as Partial Replacement of Fine Aggregate on Roller Compacted Concrete with Different Curing Methods

Directory of Open Access Journals (Sweden)

Abeer Abdulqader Salih

2016-09-01

Full Text Available Roller-Compacted Concrete is a no-slump concrete, with no reinforcing steel, no forms, no finishing and wet enough to support compaction by vibratory rollers. Due to the effect of curing on properties and durability of concrete, the main purpose of this research is to study the effect of various curing methods (air curing, 7 days water curing, and permanent water curing and porcelanite (local material used as an Internal Curing agent with different replacement percentages of fine aggregate (volumetric replacement on some properties of Roller-Compacted Concrete and to explore the possibility of introducing practical Roller-Compacted Concrete for road pavement with minimum requirement of curing. Specimens were sawed from slabs of (380*380*100 mm for determination of Ultrasonic Pulse Velocity (UPV and Voids volume. Results show that using (5 % porcelanite improved the results of UPV and Voids volume of Roller-Compacted Concrete (with air curing as compared with reference Roller-Compacted Concrete (with permanent water curing by percentages ranging from(3.6 to 28.9% and (-8 to -15.5% respectively.

Biomechanical pole and leg characteristics during uphill diagonal roller skiing.

Science.gov (United States)

Lindinger, Stefan Josef; Göpfert, Caroline; Stöggl, Thomas; Müller, Erich; Holmberg, Hans-Christer

2009-11-01

Diagonal skiing as a major classical technique has hardly been investigated over the last two decades, although technique and racing velocities have developed substantially. The aims of the present study were to 1) analyse pole and leg kinetics and kinematics during submaximal uphill diagonal roller skiing and 2) identify biomechanical factors related to performance. Twelve elite skiers performed a time to exhaustion (performance) test on a treadmill. Joint kinematics and pole/plantar forces were recorded separately during diagonal roller skiing (9 degrees; 11 km/h). Performance was correlated to cycle length (r = 0.77; P Push-off demonstrated performance correlations for impulse of leg force (r = 0.84), relative duration (r= -0.76) and knee flexion (r = 0.73) and extension ROM (r = 0.74). Relative time to peak pole force was associated with performance (r = 0.73). In summary, diagonal roller skiing performance was linked to 1) longer cycle length, 2) greater impulse of force during a shorter push-off with larger flexion/extension ROMs in leg joints, 3) longer leg swing, and 4) later peak pole force, demonstrating the major key characteristics to be emphasised in training.

Kinematics and Path Following Control of an Articulated Drum Roller

Science.gov (United States)

BIAN, Yongming; YANG, Meng; FANG, Xiaojun; WANG, Xiahui

2017-07-01

Automatic navigation of an articulated drum roller, which is an articulated steering type vehicle widely used in the construction industry, is highly expected for operation cost reduction and improvement of work efficiency. In order to achieve the path following control, considering that its steering system is articulated steering and two frames are articulated by an active revolute joint, a kinematic model and an error dynamic state-space equation of an articulated drum roller are proposed. Besides, a state-feedback control law based on Lyapunov stability theory is also designed, which can be proved to achieve the purpose of control by the analysis of stability. What's more, to evaluate the performance of the proposed method, simulation under the MATLAB/Simulink and experiments using positioning algorithm and errors correction at the uneven construction site are performed, with initial displacement error (-1.5 m), heading error (-0.11 rad) and steering angle (-0.19 rad). Finally, simulation and experimental results show that the errors and steering angle can decrease gradually, and converge to zero with time. Meanwhile, the control input is not saturated. An articulated drum roller can lock into a desired path with the proposed method in uneven fields.

Wayside Bearing Fault Diagnosis Based on a Data-Driven Doppler Effect Eliminator and Transient Model Analysis

Science.gov (United States)

Liu, Fang; Shen, Changqing; He, Qingbo; Zhang, Ao; Liu, Yongbin; Kong, Fanrang

2014-01-01

A fault diagnosis strategy based on the wayside acoustic monitoring technique is investigated for locomotive bearing fault diagnosis. Inspired by the transient modeling analysis method based on correlation filtering analysis, a so-called Parametric-Mother-Doppler-Wavelet (PMDW) is constructed with six parameters, including a center characteristic frequency and five kinematic model parameters. A Doppler effect eliminator containing a PMDW generator, a correlation filtering analysis module, and a signal resampler is invented to eliminate the Doppler effect embedded in the acoustic signal of the recorded bearing. Through the Doppler effect eliminator, the five kinematic model parameters can be identified based on the signal itself. Then, the signal resampler is applied to eliminate the Doppler effect using the identified parameters. With the ability to detect early bearing faults, the transient model analysis method is employed to detect localized bearing faults after the embedded Doppler effect is eliminated. The effectiveness of the proposed fault diagnosis strategy is verified via simulation studies and applications to diagnose locomotive roller bearing defects. PMID:24803197

Exercise in Configurable Products using Creo parametric

DEFF Research Database (Denmark)

Christensen, Georg Kronborg

2017-01-01

Family tables is a long know method with ProEngineer/Creo parametric to make families of products – like families of bolts and roller bearings. Configurable Products expand these possibilities in two major ways: First it makes configurable assemblies possible where one topologically different com...... been available as: configurable assemblies in earlier versions of Creo) An example of a practical application of configurable products is shown below where an outdoor Play/Exercise system is transferred from AutoCAD 2D to a 3D configurable product in Creo 3.0....

Simulation and Analysis of Roller Chain Drive Systems

DEFF Research Database (Denmark)

Pedersen, Sine Leergaard

The subject of this thesis is simulation and analysis of large roller chain drive systems, such as e.g. used in marine diesel engines. The aim of developing a chain drive simulation program is to analyse dynamic phenomena of chain drive systems and investigate different design changes to the syst......The subject of this thesis is simulation and analysis of large roller chain drive systems, such as e.g. used in marine diesel engines. The aim of developing a chain drive simulation program is to analyse dynamic phenomena of chain drive systems and investigate different design changes...... mathematical models, and compare to the prior done research. Even though the model is developed at first for the use of analysing chain drive systems in marine engines, the methods can with small changes be used in general, as for e.g. chain drives in industrial machines, car engines and motorbikes. A novel...

A method of increasing the depth of the plastically deformed layer in the roller burnishing process

Science.gov (United States)

Kowalik, Marek; Trzepiecinski, Tomasz

2018-05-01

The subject of this paper is an analysis of the determination of the depth of the plastically deformed layer in the process of roller burnishing a shaft using a newly developed method in which a braking moment is applied to the roller. It is possible to increase the depth of the plastically deformed layer by applying the braking moment to the roller during the burnishing process. The theoretical considerations presented are based on the Hertz-Bielayev and Huber-Mises theories and permit the calculation of the depth of plastic deformation of the top layer of the burnished shaft. The theoretical analysis has been verified experimentally and using numerical calculations based on the finite element method using the Msc.MARC program. Experimental tests were carried out on ring-shaped samples made of C45 carbon steel. The samples were burnished at different values of roller force and different values of braking moment. A significant increase was found in the depth of the plastically deformed surface layer of roller burnished shafts. Usage of the phenomenon of strain hardening of steel allows the technology presented here to increase the fatigue life of the shafts.

Assessment of solid microneedle rollers to enhance transmembrane delivery of doxycycline and inhibition of MMP activity.

Science.gov (United States)

Omolu, Abbie; Bailly, Maryse; Day, Richard M

2017-11-01

Many chronic wounds exhibit high matrix metalloproteinase (MMP) activity that impedes the normal wound healing process. Intradermal delivery (IDD) of sub-antimicrobial concentrations of doxycycline, as an MMP inhibitor, could target early stages of chronic wound development and inhibit further wound progression. To deliver doxycycline intradermally, the skin barrier must be disrupted. Microneedle rollers offer a minimally invasive technique to penetrate the skin by creating multiple microchannels that act as temporary conduits for drugs to diffuse through. In this study, an innovative and facile approach for delivery of doxycycline across Strat-M TM membrane was investigated using microneedle rollers. The quantity and rate of doxycycline diffusing through the micropores directly correlated with increasing microneedle lengths (250, 500 and 750 μm). Treatment of Strat-M TM with microneedle rollers resulted in a reduction in fibroblast-mediated collagen gel contraction and MMP activity compared with untreated Strat-M TM . Our results show that treatment of an epidermal mimetic with microneedle rollers provides sufficient permeabilization for doxycycline diffusion and inhibition of MMP activity. We conclude that microneedle rollers are a promising, clinically ready tool suitable for delivery of doxycycline intradermally to treat chronic wounds.

Stepping-Motion Motor-Control Subsystem For Testing Bearings

Science.gov (United States)

Powers, Charles E.

1992-01-01

Control subsystem closed-loop angular-position-control system causing motor and bearing under test to undergo any of variety of continuous or stepping motions. Also used to test bearing-and-motor assemblies, motors, angular-position sensors including rotating shafts, and like. Monitoring subsystem gathers data used to evaluate performance of bearing or other article under test. Monitoring subsystem described in article, "Monitoring Subsystem For Testing Bearings" (GSC-13432).

Roller-massager application to the quadriceps and knee-joint range of motion and neuromuscular efficiency during a lunge.

Science.gov (United States)

Bradbury-Squires, David J; Noftall, Jennifer C; Sullivan, Kathleen M; Behm, David G; Power, Kevin E; Button, Duane C

2015-02-01

Roller massagers are used as a recovery and rehabilitative tool to initiate muscle relaxation and improve range of motion (ROM) and muscular performance. However, research demonstrating such effects is lacking. To determine the effects of applying a roller massager for 20 and 60 seconds on knee-joint ROM and dynamic muscular performance. Randomized controlled clinical trial. University laboratory. Ten recreationally active men (age = 26.6 ± 5.2 years, height = 175.3 ± 4.3 cm, mass = 84.4 ± 8.8 kg). Participants performed 3 randomized experimental conditions separated by 24 to 48 hours. In condition 1 (5 repetitions of 20 seconds) and condition 2 (5 repetitions of 60 seconds), they applied a roller massager to the quadriceps muscles. Condition 3 served as a control condition in which participants sat quietly. Visual analog pain scale, electromyography (EMG) of the vastus lateralis (VL) and biceps femoris during roller massage and lunge, and knee-joint ROM. We found no differences in pain between the 20-second and 60-second roller-massager conditions. During 60 seconds of roller massage, pain was 13.5% (5.7 ± 0.70) and 20.6% (6.2 ± 0.70) greater at 40 seconds and 60 seconds, respectively, than at 20 seconds (P joint ROM was 10% and 16% greater in the 20-second and 60-second roller-massager conditions, respectively, than the control condition (P joint ROM and neuromuscular efficiency during a lunge.

Nuclear fuel assembly

International Nuclear Information System (INIS)

Delafosse, Jacques.

1977-01-01

This invention relates to a nuclear fuel assembly for a light or heavy water reactor, or for a fast reactor of the kind with a bundle of cladded pins, maintained parallel to each other in a regular network by an assembly of separate supporting grids, fitted with elastic bearing surfaces on these pins [fr

Simulation of accelerated strip cooling on the hot rolling mill run-out roller table

International Nuclear Information System (INIS)

Muhin, U.; Belskij, S.; Makarov, E.; Koinov, T.

2013-01-01

Full text: A mathematical model of the thermal state of the metal on the run-out roller table of a continuous wide hot-strip mill is presented. The mathematical model takes into account the heat generation during the polymorphic γ → α transformation of super cooled austenite phase and the influence of chemical composition on the physical properties of the steel. The model allows the calculation of modes of accelerated cooling of strips on the run-out roller table of a continuous wide hot strip mill. Winding temperature calculation error does not exceed 20 °C for 98.5 % of the strips from low-carbon and low-alloyed steels. key words: hot rolled, wide-strip, accelerated cooling, run-out roller table, polymorphic transformation, mathematical modeling

Increasing the Energy Efficiency of the Cyclic Action Mechanisms in Rolling for a Roller Bed Used as an Example

Science.gov (United States)

andreev, A. N.; Kolesnichenko, D. A.

2017-12-01

The possibility of increasing the energy efficiency of the production cycle in a roller bed is briefly reviewed and justified. The sequence diagram of operation of the electrical drive in a roller bed is analyzed, and the possible increase in the energy efficiency is calculated. A method for energy saving is described for the application of a frequency-controlled asynchronous electrical drive of drive rollers in a roller bed with an increased capacitor capacity in a dc link. A fine mathematical model is developed to describe the behavior of the electrical drive during the deceleration of a roller bed. An experimental setup is created and computer simulation and physical modeling are performed. The basic information flows of the general hierarchical automatic control system of an enterprise are described and determined with allowance for the proposed method of increasing the energy efficiency.

Do Maximal Roller Skiing Speed and Double Poling Performance Predict Youth Cross-Country Skiing Performance?

Directory of Open Access Journals (Sweden)

Roland Stöggl, Erich Müller, Thomas Stöggl

2017-09-01

Full Text Available The aims of the current study were to analyze whether specific roller skiing tests and cycle length are determinants of youth cross-country (XC skiing performance, and to evaluate sex specific differences by applying non-invasive diagnostics. Forty-nine young XC skiers (33 boys; 13.8 ± 0.6 yrs and 16 girls; 13.4 ± 0.9 yrs performed roller skiing tests consisting of both shorter (50 m and longer durations (575 m. Test results were correlated with on snow XC skiing performance (PXC based on 3 skating and 3 classical distance competitions (3 to 6 km. The main findings of the current study were: 1 Anthropometrics and maturity status were related to boys’, but not to girls’ PXC; 2 Significant moderate to acceptable correlations between girls’ and boys’ short duration maximal roller skiing speed (double poling, V2 skating, leg skating and PXC were found; 3 Boys’ PXC was best predicted by double poling test performance on flat and uphill, while girls’ performance was mainly predicted by uphill double poling test performance; 4 When controlling for maturity offset, boys’ PXC was still highly associated with the roller skiing tests. The use of simple non-invasive roller skiing tests for determination of PXC represents practicable support for ski clubs, schools or skiing federations in the guidance and evaluation of young talent.

Laboratory procedure for sizing and electroless nickel plating assembled steel bearings

International Nuclear Information System (INIS)

Wright, R.R.; Petit, G.S.

1976-01-01

The bearing is placed in a holder and degreased in methyl chloroform. The entire bearing is etched in hydrochloric acid and sized in an ammonium bifluoride-hydrogen peroxide solution (NH 4 F.HF--H 2 O 2 ). The bearing is removed from the holder, activated in hydrochloric acid and plated with 0.001 in. of nickel in a plating tumbler immersed in a heated electroless nickel plating bath. The bearing is water-rinsed and air-dried

Visualization and prediction of porosity in roller compacted ribbonswith near infrared chemical imaging (NIR-CI)

DEFF Research Database (Denmark)

Khorasani, Milad Rouhi; Amigo Rubio, Jose Manuel; Sonnergaard, Jørn

2015-01-01

The porosity of roller compacted ribbon is recognized as an important critical quality attribute which has a huge impact on the final product quality. The purpose of this study was to investigate the use of near-infrared chemical imaging (NIR-CI) for porosity estimation of ribbons produced...... and control of continuously operating roller compaction line....

Dynamic Characteristics of Rotors on Passive and Active Thrust Fluid-film Bearings with Fixed Pads

Directory of Open Access Journals (Sweden)

Babin Alexander

2018-01-01

Full Text Available Application of fluid-film bearings in rotor machines in many cases could have no alternative due to obvious advantages when compared to roller element bearings. Integration of information technology in mechanical engineering resulting in emergence of a new field of research – mechatronic bearings which allowed tracking condition of the most important parts of a machine and adjusting operational parameters of the system. Application of servo valves to control the flow rate through a fluid-film bearing is the most universal and simple way of rotor’s position control due to relative simplicity of modelling and absence of need to radically change the design of conventional hydrodynamic bearings. In the present paper numerical simulations of passive (conventional as opposed to mechatronic and active hybrid thrust fluid-film bearings with a central feeding chamber are presented, that are parts of a mechatronic rotor-bearing node. Numerical model of an active thrust bearing is based on solution of equations of hydrodynamics, rotor dynamics and an additional model of a servo valve. Various types of control have been investigated: P, PI and PID control, and the dynamic behaviour of a system has been estimated under various loads, namely static, periodic and impulse. A design of a test rig has been proposed to study passive and active thrust fluid-film bearings aimed at, among other, validation of numerical results of active bearings simulation.

Analysis of laboratory compaction methods of roller compacted concrete

Science.gov (United States)

Trtík, Tomáš; Chylík, Roman; Bílý, Petr; Fládr, Josef

2017-09-01

Roller-Compacted Concrete (RCC) is an ordinary concrete poured and compacted with machines typically used for laying of asphalt road layers. One of the problems connected with this technology is preparation of representative samples in the laboratory. The aim of this work was to analyse two methods of preparation of RCC laboratory samples with bulk density as the comparative parameter. The first method used dynamic compaction by pneumatic hammer. The second method of compaction had a static character. The specimens were loaded by precisely defined force in laboratory loading machine to create the same conditions as during static rolling (in the Czech Republic, only static rolling is commonly used). Bulk densities obtained by the two compaction methods were compared with core drills extracted from real RCC structure. The results have shown that the samples produced by pneumatic hammer tend to overestimate the bulk density of the material. For both compaction methods, immediate bearing index test was performed to verify the quality of compaction. A fundamental difference between static and dynamic compaction was identified. In static compaction, initial resistance to penetration of the mandrel was higher, after exceeding certain limit the resistance was constant. This means that the samples were well compacted just on the surface. Specimens made by pneumatic hammer actively resisted throughout the test, the whole volume was uniformly compacted.

Neuromuscular Responses of Elite Skaters During Different Roller Figure Skating Jumps

Directory of Open Access Journals (Sweden)

Pantoja Patrícia Dias

2014-07-01

Full Text Available This study aimed to describe the neuromuscular activity of elite athletes who performed various roller figure skating jumps, to determine whether the muscle activation is greater during jumps with more rotations and in which phase the muscles are more active. This study also aimed to analyze if there is any difference in the muscle activity pattern between female and male skaters. Four elite skaters were evaluated, and each participated in two experimental sessions. During the first session, anthropometric data were collected, and the consent forms were signed. For the second session, neuromuscular data were collected during jumps, which were performed with skates at a rink. The following four roller figure skating jumps were evaluated: single Axel, double Axel, double Mapes and triple Mapes. The neuromuscular activity of the following seven muscles was obtained with an electromyograph which was fixed to the waist of each skater with a strap: biceps femoris, lateral gastrocnemius, tibialis anterior, rectus femoris, vastus lateralis, vastus medialis and gluteus maximus. The signal was transmitted wirelessly to a laptop. During the roller figure skating jumps, the lateral gastrocnemius, rectus femoris, vastus lateralis, biceps femoris and gluteus maximus, showed more activation during the jumps with more rotations, and the activation mainly occurred during the propulsion and flight phases. Female skaters demonstrated higher muscle activities in tibialis anterior, vastus lateralis, vastus medialis and gluteus maximus during the landing phase of the triple Mapes, when compared to their male counterparts. The results obtained in this study should be considered when planning training programs with specific exercises that closely resemble the roller figure skating jumps. This may be important for the success of elite skaters in competitions.

Neuromuscular Responses of Elite Skaters During Different Roller Figure Skating Jumps

Science.gov (United States)

Pantoja, Patrícia Dias; Mello, André; Liedtke, Giane Veiga; Kanitz, Ana Carolina; Cadore, Eduardo Lusa; Pinto, Stephanie Santana; Alberton, Cristine Lima; Kruel, Luiz Fernando Martins

2014-01-01

This study aimed to describe the neuromuscular activity of elite athletes who performed various roller figure skating jumps, to determine whether the muscle activation is greater during jumps with more rotations and in which phase the muscles are more active. This study also aimed to analyze if there is any difference in the muscle activity pattern between female and male skaters. Four elite skaters were evaluated, and each participated in two experimental sessions. During the first session, anthropometric data were collected, and the consent forms were signed. For the second session, neuromuscular data were collected during jumps, which were performed with skates at a rink. The following four roller figure skating jumps were evaluated: single Axel, double Axel, double Mapes and triple Mapes. The neuromuscular activity of the following seven muscles was obtained with an electromyograph which was fixed to the waist of each skater with a strap: biceps femoris, lateral gastrocnemius, tibialis anterior, rectus femoris, vastus lateralis, vastus medialis and gluteus maximus. The signal was transmitted wirelessly to a laptop. During the roller figure skating jumps, the lateral gastrocnemius, rectus femoris, vastus lateralis, biceps femoris and gluteus maximus, showed more activation during the jumps with more rotations, and the activation mainly occurred during the propulsion and flight phases. Female skaters demonstrated higher muscle activities in tibialis anterior, vastus lateralis, vastus medialis and gluteus maximus during the landing phase of the triple Mapes, when compared to their male counterparts. The results obtained in this study should be considered when planning training programs with specific exercises that closely resemble the roller figure skating jumps. This may be important for the success of elite skaters in competitions. PMID:25114728

Modeling of Comparative Performance of Asphalt Concrete under Hammer, Gyratory, and Roller Compaction

Directory of Open Access Journals (Sweden)

Saad I. Sarsam

2016-11-01

Full Text Available The main objective of this study is to develop predictive models using SPSS software (version 18 for Marshall Test results of asphalt mixtures compacted by Hammer, Gyratory, and Roller compaction. Bulk density of (2.351 gm/cc, at OAC of (4.7 % was obtained as a benchmark after using Marshall Compactor as laboratory compactive effort with 75-blows. Same density was achieved by Roller and Gyratory Compactors using its mix designed methods. A total of (75 specimens, for Marshall, Gyratory, and Roller Compactors have been prepared, based on OAC of (4.7 % with an additional asphalt contents of more and less than (0.5 % from the optimum value. All specimens have been subjected to Marshall Test. Mathematical models obtained indicated that variation of Marshall Stiffness is based on the variation of air voids. All of these models depend on asphalt cement content too.

DETERMINATION OF ADHESIVE STRENGTH LAYER’S ROLLER COMPACTED CONCRETE THE METHOD AXIAL EXTENSION

Directory of Open Access Journals (Sweden)

Tang Van Lam

2017-07-01

Full Text Available Roller compacted concrete for the construction of hydraulic and hydroelectric buildings is a composite material, which consists of a binder, fine aggregate (sand, coarse aggregate (gravel or crushed stone, water and special additives that provide the desired concrete workability and impart the required concrete performance properties. Concrete mixture is prepared at from concrete mixing plants strictly metered quantities of cement, water, additives and graded aggregates, whereupon they are delivered to the site laying Mixer Truck and sealing layers with each stack layer. The advantages of roller compaction technology should include the reduction of construction time, which allows fast commissioning construction projects, as well as reduce the amount of investment required. One of the main problems encountered in the process of roller compaction of the concrete mix is the need to provide the required adhesion strength between layers of concrete. This paper presents a method for determining the strength of adhesion between the concrete layers of different ages roller compacted concrete using axial tension. This method makes it possible to obtain objective and accurate results with a total thickness of layers of compacted concrete of up to 300…400 mm. Results from this method, studies have shown that the value of strength between the concrete layers in addition to the composition of the concrete and adhesion depends on the quality and the parallel end surfaces of the cylinder-models, which are mounted steel plates for axial tension, as well as the state of the contact surfaces of the concrete layer. The method can be used to determine the strength of interlayer adhesion in roller compacted concrete, which are used in the construction of dams and other hydraulic structures.

To Enhance the Fire Resistance Performance of High-Speed Steel Roller Door with Water Film System

Directory of Open Access Journals (Sweden)

De-Hua Chung

2015-01-01

Full Text Available The structure of high-speed roller door with water film has improved in this study. The flameproof water film system is equipped with a water circulating device to reduce the water consumption of water film system. The water film is generated at the roller box of the high-speed roller door in this study. The heating test is done with the full-scale heating furnace. Both cases of the water film on unexposed surface and water film on exposed surface passed the fire resistance test based on ISO 834, proving that the high-speed roller door with water film system has 120A fire resistance period. The main findings indicate that the water film on exposed surface shows that as the amount of water film evaporated by high temperature inside the furnace must be greater than the evaporation capacity of water film on unexposed surface, the required water supply is 660 L more than the water film on unexposed surface.

Assesment on Reproductive Performance and Hormonal Studies in Rural Women Beedi Rollers in Jagitial District of Telangana State

Directory of Open Access Journals (Sweden)

Vanitha Baluka

2017-10-01

Full Text Available Beedi manufacturing is the second largest industry in India. It provides employment to millions of women mostly from the poor socioeconomic class. In North region of Telangana, beedi rolling is a major occupation for illiterate women in many villages. It may affect due to the inhalation of unfiltered tobacco dust and volatile and toxic components of tobacco. Biomonitoring of women beedi rollers and their reproductive performance assessment is necessary to take prevention/control the reproduction failure and carcinogen effect on cervical system. Continuous exposed to unfiltered tobacco dust may have systemic effect and lead to many disorders including hormone defects and reproductive health problems. Although studies have been carried out on beedi industry workers and tobacco smoke exposed people at national and international level, no such studies were carried out on women beedi rollers living in rural areas in Telangana State. Hence, this investigation is attempted to understand the study is find to association with hormonal levels and reproductive outcome in rural women beedi rollers of reproductive age in North Telangana. Statistical analysis was done for the obtained results to find the significance between the two groups for the reproductive outcome and Hormonal Studies. Total 50 women (married who are exposed minimum 6-10 years to the unfiltered tobacco dust beedi rollers in the age group of 25 to 45 years from villages of Jagitial district were enrolled for this study. 50 equal numbers of women in the same age group belonging to the same socio economic status and not exposed occupationally to chemical and physical agents was selected for comparison (control group. Estroidal, Progesterone the T3, T4 and TSH levels were measured found significantly T3, T4 levels were low in the beedi rollers, compared the controls. TSH levels were found to be higher in the beedi rollers. Estroidal and progesterone levels were obtained non

Application of a local linearization technique for the solution of a system of stiff differential equations associated with the simulation of a magnetic bearing assembly

Science.gov (United States)

Kibler, K. S.; Mcdaniel, G. A.

1981-01-01

A digital local linearization technique was used to solve a system of stiff differential equations which simulate a magnetic bearing assembly. The results prove the technique to be accurate, stable, and efficient when compared to a general purpose variable order Adams method with a stiff option.

Optimum IMFs Selection Based Envelope Analysis of Bearing Fault Diagnosis in Plunger Pump

Directory of Open Access Journals (Sweden)

Wenliao Du

2016-01-01

Full Text Available As the plunger pump always works in a complicated environment and the hydraulic cycle has an intrinsic fluid-structure interaction character, the fault information is submerged in the noise and the disturbance impact signals. For the fault diagnosis of the bearings in plunger pump, an optimum intrinsic mode functions (IMFs selection based envelope analysis was proposed. Firstly, the Wigner-Ville distribution was calculated for the acquired vibration signals, and the resonance frequency brought on by fault was obtained. Secondly, the empirical mode decomposition (EMD was employed for the vibration signal, and the optimum IMFs and the filter bandwidth were selected according to the Wigner-Ville distribution. Finally, the envelope analysis was utilized for the selected IMFs filtered by the band pass filter, and the fault type was recognized by compared with the bearing character frequencies. For the two modes, inner race fault and compound fault in the inner race and roller of rolling element bearing in plunger pump, the experiments show that a promising result is achieved.

Validation of a Functional Pyelocalyceal Renal Model for the Evaluation of Renal Calculi Passage While Riding a Roller Coaster.

Science.gov (United States)

Mitchell, Marc A; Wartinger, David D

2016-10-01

The identification and evaluation of activities capable of dislodging calyceal renal calculi require a patient surrogate or validated functional pyelocalyceal renal model. To evaluate roller coaster facilitation of calyceal renal calculi passage using a functional pyelocalyceal renal model. A previously described adult ureteroscopy and renoscopy simulator (Ideal Anatomic) was modified and remolded to function as a patient surrogate. Three renal calculi of different sizes from the patient who provided the original computed tomographic urograph on which the simulator was based were used. The renal calculi were suspended in urine in the model and taken for 20 rides on the Big Thunder Mountain Railroad roller coaster at Walt Disney World in Orlando, Florida. The roller coaster rides were analyzed using variables of renal calculi volume, calyceal location, model position on the roller coaster, and renal calculi passage. Sixty renal calculi rides were analyzed. Independent of renal calculi volume and calyceal location, front seating on the roller coaster resulted in a passage rate of 4 of 24. Independent of renal calculi volume and calyceal location, rear seating on the roller coaster resulted in a passage rate of 23 of 36. Independent of renal calculi volume in rear seating, calyceal location differed in passage rates, with an upper calyceal calculi passage rate of 100%; a middle calyceal passage rate of 55.6%; and a lower calyceal passage rate of 40.0%. The functional pyelocalyceal renal model serves as a functional patient surrogate to evaluate activities that facilitate calyceal renal calculi passage. The rear seating position on the roller coaster led to the most renal calculi passages.

Development and Evaluation of Titanium Spacesuit Bearings

Science.gov (United States)

Rhodes, Richard; Battisti, Brian; Ytuarte, Raymond, Jr.; Schultz, Bradley

2016-01-01

The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z-series of spacesuits, designed with the intent of meeting a wide variety of exploration mission objectives, including human exploration of the Martian surface. Incorporating titanium bearings into the Z-series space suit architecture allows us to reduce mass by an estimated 23 lbs per suit system compared to the previously used stainless steel bearing race designs, without compromising suit functionality. There are two obstacles to overcome when using titanium for a bearing race- 1) titanium is flammable when exposed to the oxygen wetted environment inside the space suit and 2) titanium's poor wear properties are often challenging to overcome in tribology applications. In order to evaluate the ignitability of a titanium space suit bearing, a series of tests were conducted at White Sands Test Facility (WSTF) that introduced the bearings to an extreme test profile, with multiple failures imbedded into the test bearings. The testing showed no signs of ignition in the most extreme test cases; however, substantial wear of the bearing races was observed. In order to design a bearing that can last an entire exploration mission (approx. 3 years), design parameters for maximum contact stress need to be identified. To identify these design parameters, bearing test rigs were developed that allow for the quick evaluation of various bearing ball loads, ball diameters, lubricants, and surface treatments. This test data will allow designers to minimize the titanium bearing mass for a specific material and lubricant combination and design around a cycle life requirement for an exploration mission. This paper reviews the current research and testing that has been performed on titanium bearing races to evaluate the use of such materials in an enriched oxygen environment and to optimize the bearing assembly mass and tribological properties to accommodate for the high bearing cycle life for an

Pervasive liquid metal based direct writing electronics with roller-ball pen

Directory of Open Access Journals (Sweden)

Yi Zheng

2013-11-01

Full Text Available A roller-ball pen enabled direct writing electronics via room temperature liquid metal ink was proposed. With the rolling to print mechanism, the metallic inks were smoothly written on flexible polymer substrate to form conductive tracks and electronic devices. The contact angle analyzer and scanning electron microscope were implemented to disclose several unique inner properties of the obtained electronics. An ever high writing resolution with line width and thickness as 200 μm and 80 μm, respectively was realized. Further, with the administration of external writing pressure, GaIn24.5 droplets embody increasing wettability on polymer which demonstrates the pervasive adaptability of the roller-ball pen electronics.

High-energy roller injuries to the upper extremity.

Science.gov (United States)

Askins, G; Finley, R; Parenti, J; Bush, D; Brotman, S

1986-12-01

Eleven cases of high-energy industrial roller injuries treated between 1980 and 1984 were retrospectively reviewed. The dominant extremity was affected in nine. Six patients sustained fractures and/or dislocations, and three of these patients required fasciotomies for clinical signs of impending compartment syndromes. All fracture/dislocations, with the exception of a scapula fracture, anterior dislocation of a thumb interphalangeal joint, and a fractured coronoid process of the ulna, required open reduction with internal fixation. Three patients required split-thickness skin grafting for extensive skin degloving. Two patients required immediate amputation. Late sequelae included prolonged edema, nutritional depletion, neuroma formation of the superficial branch of the radial nerve, late carpal tunnel syndrome, and partial brachial plexus palsy. Industrial roller injuries continue to be an occupational hazard associated with more severe crushing trauma than the low-energy wringer washer injuries first described by MacCollum (11). Attention must be paid to the treatment of crushed skin, muscle, and nerves, fracture stabilization, nutritional support, and occupational therapy. Concurrent monitoring for signs of a developing compartment syndrome and complications of rhabdomyolysis is essential.

Scale up of diesel oil biodegradation in a baffled roller bioreactor.

Science.gov (United States)

Nikakhtari, Hossein; Song, Wanning; Kumar, Pardeep; Nemati, Mehdi; Hill, Gordon A

2010-05-01

Diesel oil is a suitable substance to represent petroleum contamination from accidental spills in operating and transportation facilities. Using a microbial culture enriched from a petroleum contaminated soil, biodegradation of diesel oil was carried out in 2.2, 55, and 220 L roller baffled bioreactors. The effects of bioreactor rotation speed (from 5 to 45 rpm) and liquid loading (from 18% to 73% of total volume) on the biodegradation of diesel oil were studied. In the small scale bioreactor (2.2L), the maximum rotation speed of 45 rpm resulted in the highest biodegradation rate with a first order biodegradation kinetic constant of 0.095 d(-1). In the larger scale bioreactors, rotation speed did not affect the biodegradation rate. Liquid loadings higher than 64% resulted in reduced biodegradation rates in the small scale bioreactor; however, in the larger roller bioreactors liquid loading did not affect the biodegradation rate. Biodegradation of diesel oil at 5 rpm and 73% loading is recommended for operating large scale roller baffled bioreactors. Under these conditions, high diesel oil concentrations up to 50 gL(-1) can be bioremediated at a rate of 1.61 gL(-1)d(-1). Copyright 2010 Elsevier Ltd. All rights reserved.

Fabrication of a roller type PDMS stamp using SU-8 concave molds and its application for roll contact printing

International Nuclear Information System (INIS)

Park, Jongho; Kim, Beomjoon

2016-01-01

Continuous fabrication of micropatterns at low-cost is attracting attention in various applications within industrial fields. To meet such demands, we have demonstrated a roll contact printing technique, using roller type polydimethylsiloxane (PDMS) stamps with roll-to-flat and roll-to-roll stages. Roller type PDMS stamps for roll contact printing were fabricated using a custom-made metal support and SU-8 microstructures fabricated on concave substrates as a mold. The molding/casting method which we developed here provided faster and easier fabrication than conventional methods for roller type stamps. Next, roll contact printing was performed using fabricated roller type PDMS stamps with roll-to-flat and roll-to-roll stages. Patterns with minimum widths of 3 μm and 2.1 μm were continuously fabricated for each stage, respectively. In addition, the relationship between applied pressures and dimensional changes of roll contact printed patterns was investigated. Finally, we confirmed that roll contact printing and the new fabrication method for roller stamps presented in this study demonstrated the feasibility for industrial applications. (paper)

Sub-surface Fatigue Crack Growth at Alumina Inclusions in AISI 52100 Roller Bearings

DEFF Research Database (Denmark)

Cerullo, Michele

2014-01-01

Sub-surface fatigue crack growth at non metallic inclusions is studied in AISI 52100 bearing steel under typical rolling contact loads. A first 2D plane strain finite element analysis is carried out to compute the stress history in the innner race at a characteristic depth, where the Dang Van...... damage factor is highest. Subsequently the stress history is imposed as boundary conditions in a periodic unit cell model, where an alumina inclusion is embedded in a AISI 52100 matrix. Cracks are assumed to grow radially from the inclusion under cyclic loading. The growth is predicted by means...

Visualization in mechanics: the dynamics of an unbalanced roller

Science.gov (United States)

Cumber, Peter S.

2017-04-01

It is well known that mechanical engineering students often find mechanics a difficult area to grasp. This article describes a system of equations describing the motion of a balanced and an unbalanced roller constrained by a pivot arm. A wide range of dynamics can be simulated with the model. The equations of motion are embedded in a graphical user interface for its numerical solution in MATLAB. This allows a student's focus to be on the influence of different parameters on the system dynamics. The simulation tool can be used as a dynamics demonstrator in a lecture or as an educational tool driven by the imagination of the student. By way of demonstration the simulation tool has been applied to a range of roller-pivot arm configurations. In addition, approximations to the equations of motion are explored and a second-order model is shown to be accurate for a limited range of parameters.

Effects of frequency on gross efficiency and performance in roller ski skating.

Science.gov (United States)

Leirdal, S; Sandbakk, O; Ettema, G

2013-06-01

The purpose of the present study was to examine the effect of frequency on efficiency and performance during G3 roller ski skating. Eight well-trained male cross-country skiers performed three submaximal 5-min speeds (10, 13, and 16 km/h) and a time-to-exhaustion (TTE) performance (at 20 km/h) using the G3 skating technique using freely chosen, high, and low frequency at all four speeds. All tests were done using roller skis on a large treadmill at 5% incline. Gross efficiency (GE) was calculated as power divided by metabolic rate. Power was calculated as the sum of power against frictional forces and power against gravity. Metabolic rate was calculated from oxygen consumption and blood lactate concentration. Freely chosen frequency increased from 60 to 70 strokes/min as speed increased from 10 to 20 km/h. GE increased with power. At high power (20 km/h performance test), both efficiency and performance were significantly reduced by high frequency. In regard to choice of frequency during G3 roller ski skating, cross-country skiers seems to be self-optimized both in relation to energy saving (efficiency) and performance (TTE). © 2011 John Wiley & Sons A/S.

75 FR 76297 - Defense Federal Acquisition Regulation Supplement; Restriction on Ball and Roller Bearings (DFARS...

Science.gov (United States)

2010-12-08

... does not have enough market leverage for it to be in the business interest of the manufacturers and... reason for changing the rule is statutory change. 10 U.S.C. 2534(a)(5) is no longer in effect because... Government leverage with regard to acquisition of commercial bearings. The Government continues to issue more...

Corrective action plan for CAU No. 404: Roller Coaster Sewage Lagoons and North Disposal Trench, Tonopah Test Range

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

This Corrective Action Plan (CAP) provides the selected corrective action alternative and proposes the closure implementation methodology for the Roller Coaster Sewage Lagoons and North Disposal Trench Corrective Action Unit (CAU) No. 404. The site is located on the Tonopah Test Range. CAU 404 consists of two Corrective Action Sites (CAS): the Roller Coaster Lagoons (CAS No TA-03-001-TA-RC) and the North Disposal Trench (CAS No TA-21-001-TA-RC). A site map of the lagoons and trench is provided. The Roller Coaster Sewage Lagoons are comprised of two unlined lagoons that received liquid sanitary waste in 1963 from the Operation Roller Coaster Man Camp and debris from subsequent construction and range cleanup activities. The North Disposal Trench was excavated in approximately 1963 and received solid waste and debris from the man camp and subsequent construction and range cleanup activities. A small hydrocarbon spill occurred during the 1995 Voluntary Corrective Action (VCA) activities in an area associated with the North Disposal Trench CAS.

Corrective action plan for CAU No. 404: Roller Coaster Sewage Lagoons and North Disposal Trench, Tonopah Test Range

International Nuclear Information System (INIS)

1997-07-01

This Corrective Action Plan (CAP) provides the selected corrective action alternative and proposes the closure implementation methodology for the Roller Coaster Sewage Lagoons and North Disposal Trench Corrective Action Unit (CAU) No. 404. The site is located on the Tonopah Test Range. CAU 404 consists of two Corrective Action Sites (CAS): the Roller Coaster Lagoons (CAS No TA-03-001-TA-RC) and the North Disposal Trench (CAS No TA-21-001-TA-RC). A site map of the lagoons and trench is provided. The Roller Coaster Sewage Lagoons are comprised of two unlined lagoons that received liquid sanitary waste in 1963 from the Operation Roller Coaster Man Camp and debris from subsequent construction and range cleanup activities. The North Disposal Trench was excavated in approximately 1963 and received solid waste and debris from the man camp and subsequent construction and range cleanup activities. A small hydrocarbon spill occurred during the 1995 Voluntary Corrective Action (VCA) activities in an area associated with the North Disposal Trench CAS

Camshaft bearing arrangement for overhead cam engine

Energy Technology Data Exchange (ETDEWEB)

Yoshikawa, M.

1985-01-01

In an assembly for an internal combustion engine comprising a cylinder block, a cylinder head detachably affixed to the cylinder block by a plurality of threaded fastening means, a plurality of poppet valves supported for reciprocation in the cylinder head and a camshaft for operating the poppet valves, the improvement is described comprising a cam carrier detachably affixed to the cylinder head and overlying the threaded fastening means, and a bearing cap affixed to the cam carrier. The cam carrier and the bearing cap have bearing surfaces for journaling the camshaft.

Vibratory synchronization transmission of a cylindrical roller in a vibrating mechanical system excited by two exciters

Science.gov (United States)

Zhang, Xueliang; Wen, Bangchun; Zhao, Chunyu

2017-11-01

In present work vibratory synchronization transmission (VST) of a cylindrical roller with dry friction in a vibrating mechanical system excited by two exciters, is studied. Using the average method, the criterion of implementing synchronization of two exciters and that of ensuring VST of a roller, are achieved. The criterion of stability of the synchronous states satisfies the Routh-Hurwitz principle. The influences of the structural parameters of the system to synchronization and stability, are discussed numerically, which can be served as the theoretical foundation for engineering designs. An experiment is carried out, which approximately verify the validity of the theoretical and numerical results, as well as the feasibility of the method used. Utilizing the VST theory of a roller, some types of vibrating crushing or grinding equipments, etc., can be designed.

Granule fraction inhomogeneity of calcium carbonate/sorbitol in roller compacted granules

DEFF Research Database (Denmark)

Bacher, Charlotte; Olsen, P.M.; Bertelsen, P.

2008-01-01

The granule fraction inhomogeneity of roller compacted granules was examined on mixtures of three different morphologic forms of calcium carbonate and three particle sizes of sorbitol. The granule fraction inhomogeneity was determined by the distribution of the calcium carbonate in each of the 10...... size fractions between 0 and 2000 µm and by calculating the demixing potential. Significant inhomogeneous occurrence of calcium carbonate in the size fractions was demonstrated, depending mostly on the particles sizes of sorbitol but also on the morphological forms of calcium carbonate......, the ability of the powder to agglomerate in the roller compactor was demonstrated to be related to the ability of the powder to be compacted into a tablet, thus the most compactable calcium carbonate and the smallest sized sorbitol improved the homogeneity by decreasing the demixing potential....

Influence of quartz particles on wear in vertical roller mills

DEFF Research Database (Denmark)

Jensen, Lucas R.D.; Friis, Henrik; Fundal, Erling

2010-01-01

The standard closed circuit comminution process commonly employed in industrial vertical roller mills has been analyzed to determine the influence of typical abrasive minerals on wear rates. With the main focus on raw mixes used in cement plants, synthetic mixtures imitating were prepared. Using...

ABOUT MODELING COMPLEX ASSEMBLIES IN SOLIDWORKS – LARGE AXIAL BEARING

Directory of Open Access Journals (Sweden)

Cătălin IANCU

2017-12-01

Full Text Available In this paperwork is presented the modeling strategy used in SOLIDWORKS for modeling special items as large axial bearing and the steps to be taken in order to obtain a better design. In the paper are presented the features that are used for modeling parts, and then the steps that must be taken in order to obtain the 3D model of a large axial bearing used for bucket-wheel equipment for charcoal moving.

Estimation of bearing contact angle in-situ by X-ray kinematography

Science.gov (United States)

Fowler, P. H.; Manders, F.

1982-01-01

The mounted, preloaded contact angle of the structural bearings in the assembled design mechanical assembly was measured. A modification of the Turns method is presented, based upon the clarity and definition of moving parts achieved with X-ray technique and cinematic display. Contact angle is estimated by counting the number of bearings passing a given point as a function of number of turns of the shaft. Ball and pitch diameter variations are discussed. Ball train and shaft angle uncertainties are also discussed.

Physical and mechanical behaviour of a roller compacted concrete ...

African Journals Online (AJOL)

In order to study the behaviour of a roller compacted concrete (RCC) reinforced with polypropylene fiber, six types of RCC were made with different content of fibers (0, 0.5, 1, 1.5, 2 and 2.5 Kg/m3). The physical parameters are the density, the workability, the shrinkage and the water absorption. For the mechanical ...

Experimental performance investigation of glazing system combined with internal roller blinds

DEFF Research Database (Denmark)

Larsen, Olena Kalyanova; Jensen, Rasmus Lund; Iversen, Tore Dahl

2016-01-01

Modern low-energy buildings are often associated with efficient shading devices, as an inevitable component to reduce the peak heat gain in the building and to improve visual comfort. Internal shading devices may have inferior performance compared to external shading, but these are still the most...... used in practice due to lower cost, simplicity and better acceptance between architects and users. The interplay between glazing systems and internal shading devices has been studied and in everyday practice this interplay is described by the solar shading coefficient and the total g......-value of the system (window + roller blind). Solar shading coefficient in such practice is assumed to be independent of the window properties and solar incidence angle. This paper is aimed to illustrate the deviation between the actual and assumed performance of the window system with internal roller blind. This task...

Extended Life Testing of Duplex Ball Bearings

Science.gov (United States)

Mobley, Jeffrey; Robertson, Michael; Hodges, Charles

2016-01-01

Sierra Nevada Corporation’s Space Systems performed bearing life testing for the Scan Mirror Motor/Encoder Assembly (SMMA), part of the Scan Mirror Assembly on-board the Aerosol Polarimetry Sensor (APS) on the NASA Glory Spacecraft. The baseline bearing life test duration extended beyond the launch date for the Glory Spacecraft; a risk that the program was willing to undertake with the understanding that if any anomalies or failures occurred before the required life was achieved, then the mission objectives or operating profile could be modified on orbit to take those results into account. Even though the Glory Spacecraft failed to reach orbit during its launch in March of 2011, the bearing life testing was continued through a mutual understanding of value between Sierra Nevada Corporation and our customer; with a revised goal of testing to failure rather than completing a required number of life cycles. Life testing thus far has not only exceeded the original mission required life, but has also exceeded the published test data for Cumulative Degradation Factor (CDF) from NASA/CR-2009-215681. Many lessons were learned along the way regarding long life testing. The bearing life test has been temporarily suspended due to test support equipment issues.

Superelastic Ball Bearings: Materials and Design to Avoid Mounting and Dismounting Brinell Damage in an Inaccessible Press-Fit Application-. I ; Design Approach

Science.gov (United States)

Dellacorte, Christopher; Howard, S. Adam

2015-01-01

Ball bearings require proper fit and installation into machinery structures (onto shafts and into bearing housings) to ensure optimal performance. For some applications, both the inner and outer race must be mounted with an interference fit and care must be taken during assembly and disassembly to avoid placing heavy static loads between the balls and races otherwise Brinell dent type damage can occur. In this paper, a highly dent resistant superelastic alloy, 60NiTi, is considered for rolling element bearing applications that encounter excessive static axial loading during assembly or disassembly. A small (R8) ball bearing is designed for an application in which access to the bearing races to apply disassembly tools is precluded. First Principles analyses show that by careful selection of materials, raceway curvature and land geometry, a bearing can be designed that allows blind assembly and disassembly without incurring raceway damage due to ball denting. Though such blind assembly applications are uncommon, the availability of bearings with unusually high static load capability may enable more such applications with additional benefits, especially for miniature bearings.

Mechanical Design Science

International Nuclear Information System (INIS)

Jung, Sun Mo

1969-04-01

This book contains element of machine and machine design, machine standard, a safety factor, fatigue limit like notch, creep, limits and fits for engineering, design of shaft system machine, shaft coupling and clutch, journal and roller bearing such as needle bearing, flexible roller bearing and miniature ball bearing and sliding bearing. It also deals with brake like band brake, spring such as coil spring, torsion bar spring, ring spring and fly wheel, design of pipe system machine like pipe types, joint pipes, check valve, reductive valve and escape valve.

Development of Motor Bearings for a New SADA (BepiColombo)

Science.gov (United States)

Kreuser, J.; Bachman, R.; Bergrath, B.; Heinrich, B.; Zemann, J.

2013-09-01

The special requirements of the new MPO Solar Array Drive Assembly (SADA) developed for the BepiColombo program demanded also new ball bearing designs. In addition to typical requirements for other bearings in space mechanisms, the BepiColombo mission is characterized by a non-operating time of six years at extreme environmental conditions. In cooperation with RUAG Space CEROBEAR has developed different types of ball bearings for this SADA including motor bearings for the drive, a customized stepper motor.The purpose of this paper is to present and summarize the results of the development of the motor bearings of the SADA.

Failure analysis of a helicopter's main rotor bearing

International Nuclear Information System (INIS)

Shahzad, M.; Qureshi, A.H.; Waqas, H.; Hussain, N.; Ali, N.

2011-01-01

Presented results report some of the findings of a detailed failure analysis carried out on a main rotor hub assembly, which had symptoms of burning and mechanical damage. The analysis suggests environmental degradation of the grease which causes pitting on bearing-balls. The consequent inefficient lubrication raises the temperature which leads to the smearing of cage material (brass) on the bearing-balls and ultimately causes the failure. The analysis has been supported by the microstructural studies, thermal analysis and micro-hardness testing performed on the affected main rotor bearing parts. (author)

A roller-like bird (Coracii) from the Early Eocene of Denmark.

Science.gov (United States)

Bourdon, Estelle; Kristoffersen, Anette V; Bonde, Niels

2016-09-27

The fossil record of crown group birds (Neornithes) prior to the Cretaceous-Paleogene boundary is scarce and fragmentary. Early Cenozoic bird fossils are more abundant, but are typically disarticulated and/or flattened. Here we report the oldest roller (Coracii), Septencoracias morsensis gen. et sp. nov. (Primobucconidae), based on a new specimen from the Early Eocene (about 54 million years ago) Fur Formation of Denmark. The new fossil is a nearly complete, three-dimensionally preserved and articulated skeleton. It lies at the lower end of the size range for extant rollers. Salient diagnostic features of Septencoracias relative to other Coracii include the proportionally larger skull and the small, ovoid and dorsally positioned narial openings. Our discovery adds to the evidence that the Coracii had a widespread northern hemisphere distribution in the Eocene. Septencoracias is the oldest substantial record of the Picocoraciae and provides a reliable calibration point for molecular phylogenetic studies.

Optics assembly for high power laser tools

Science.gov (United States)

Fraze, Jason D.; Faircloth, Brian O.; Zediker, Mark S.

2016-06-07

There is provided a high power laser rotational optical assembly for use with, or in high power laser tools for performing high power laser operations. In particular, the optical assembly finds applications in performing high power laser operations on, and in, remote and difficult to access locations. The optical assembly has rotational seals and bearing configurations to avoid contamination of the laser beam path and optics.

Bearing Fault Classification Based on Conditional Random Field

Directory of Open Access Journals (Sweden)

Guofeng Wang

2013-01-01

Full Text Available Condition monitoring of rolling element bearing is paramount for predicting the lifetime and performing effective maintenance of the mechanical equipment. To overcome the drawbacks of the hidden Markov model (HMM and improve the diagnosis accuracy, conditional random field (CRF model based classifier is proposed. In this model, the feature vectors sequences and the fault categories are linked by an undirected graphical model in which their relationship is represented by a global conditional probability distribution. In comparison with the HMM, the main advantage of the CRF model is that it can depict the temporal dynamic information between the observation sequences and state sequences without assuming the independence of the input feature vectors. Therefore, the interrelationship between the adjacent observation vectors can also be depicted and integrated into the model, which makes the classifier more robust and accurate than the HMM. To evaluate the effectiveness of the proposed method, four kinds of bearing vibration signals which correspond to normal, inner race pit, outer race pit and roller pit respectively are collected from the test rig. And the CRF and HMM models are built respectively to perform fault classification by taking the sub band energy features of wavelet packet decomposition (WPD as the observation sequences. Moreover, K-fold cross validation method is adopted to improve the evaluation accuracy of the classifier. The analysis and comparison under different fold times show that the accuracy rate of classification using the CRF model is higher than the HMM. This method brings some new lights on the accurate classification of the bearing faults.

Roller-coaster Ride to, Relief From TMJ | NIH MedlinePlus the Magazine

Science.gov (United States)

... on a roller coaster ride, seeking relief from temporomandibular joint (TMJ) disorder, which causes pain and, sometimes, dysfunction in the jaw joint and muscles of the neck, head, and face. She has endured: excruciating pain ...

Fire ants protect mealybugs against their natural enemies by utilizing the leaf shelters constructed by the leaf roller Sylepta derogata.

Directory of Open Access Journals (Sweden)

Aiming Zhou

Full Text Available The importance of mutualism is receiving more attention in community ecology. In this study, the fire ant Solenopsis invicta was found to take advantage of the shelters constructed by the leaf roller Sylepta derogata to protect mealybugs (Phenacoccus solenopsis against their natural enemies. This protective effect of fire ant tending on the survival of mealybugs in shelters was observed when enemies and leaf rollers were simultaneously present. Specifically, fire ants moved the mealybugs inside the shelters produced by S. derogata on enemy-infested plants. Compared with that in plants without ants, the survival of mealybugs in shelters in the presence of natural enemies in plants with ants markedly improved. Both the protection of ants and the shelters provided by leaf rollers did not affect the survival of mealybugs in the absence of enemies in plants. Ants and leaf rollers significantly improved the survival of mealybugs in predator-infested plants, whereas no such improvement was observed in parasitoid-infested ones.

Roller skating--is it a dangerous sport?

Science.gov (United States)

Tse, P Y; Shen, W Y; Chan, K M; Leung, P C

1987-01-01

A prospective survey of 111 cases of roller skating injuries within one year are reported. Males were more commonly injured than females. There was a high incidence (86%) of serious injuries, 28% of which required surgical treatment. The wrist (23%) was the commonest region involved, followed by the shoulder (20%), the elbow (15%) and the ankle (12%). Collision with other skaters and loss of control were the main factors leading to injury. Better rink discipline, instruction classes and safety publicity should be helpful in minimising accidents. Images Fig. 2 & Fig. 3 PMID:3676638

Intermittent stick-slip dynamics during the peeling of an adhesive tape from a roller.

Science.gov (United States)

Cortet, Pierre-Philippe; Dalbe, Marie-Julie; Guerra, Claudia; Cohen, Caroline; Ciccotti, Matteo; Santucci, Stéphane; Vanel, Loïc

2013-02-01

We study experimentally the fracture dynamics during the peeling at a constant velocity of a roller adhesive tape mounted on a freely rotating pulley. Thanks to a high speed camera, we measure, in an intermediate range of peeling velocities, high frequency oscillations between phases of slow and rapid propagation of the peeling fracture. This so-called stick-slip regime is well known as the consequence of a decreasing fracture energy of the adhesive in a certain range of peeling velocity coupled to the elasticity of the peeled tape. Simultaneously with stick slip, we observe low frequency oscillations of the adhesive roller angular velocity which are the consequence of a pendular instability of the roller submitted to the peeling force. The stick-slip dynamics is shown to become intermittent due to these slow pendular oscillations which produce a quasistatic oscillation of the peeling angle while keeping constant the peeling fracture velocity (averaged over each stick-slip cycle). The observed correlation between the mean peeling angle and the stick-slip amplitude questions the validity of the usually admitted independence with the peeling angle of the fracture energy of adhesives.

Simulation of accelerated strip cooling on the hot rolling mill run-out roller table

Directory of Open Access Journals (Sweden)

E.Makarov

2016-07-01

Full Text Available A mathematical model of the thermal state of the metal in the run-out roller table continuous wide hot strip mill. The mathematical model takes into account heat generation due to the polymorphic γ → α transformation of supercooled austenite phase state and the influence of the chemical composition of the steel on the physical properties of the metal. The model allows calculation of modes of accelerated cooling strips on run-out roller table continuous wide hot strip mill. Winding temperature calculation error does not exceed 20°C for 98.5 % of strips of low-carbon and low-alloy steels

60NiTi Intermetallic Material Evaluation for Lightweight and Corrosion Resistant Spherical Sliding Bearings for Aerospace Applications

Science.gov (United States)

DellaCorte, Christopher; Jefferson, Michael

2015-01-01

NASA Glenn Research Center and the Kamatics subsidiary of the Kaman Corporation conducted the experimental evaluation of spherical sliding bearings made with 60NiTi inner races. The goal of the project was to assess the feasibility of manufacturing lightweight, corrosion resistant bearings utilizing 60NiTi for aerospace and industrial applications. NASA produced the bearings in collaboration with Abbott Ball Corporation and Kamatics fabricated bearing assemblies utilizing their standard reinforced polymer liner material. The assembled bearings were tested in oscillatory motion at a load of 4.54kN (10,000 lb), according to the requirements of the plain bearing specification SAE AS81820. Several test bearings were exposed to hydraulic fluid or aircraft deicing fluid prior to and during testing. The results show that the 60NiTi bearings exhibit tribological performance comparable to conventional stainless steel (440C) bearings. Further, exposure of 60NiTi bearings to the contaminant fluids had no apparent performance effect. It is concluded that 60NiTi is a feasible bearing material for aerospace and industrial spherical bearing applications.

Roller kiln with very low fluoride emission. The Ecokiln

Energy Technology Data Exchange (ETDEWEB)

Reymer, P.S.; Denissen, A.M. [TNO TPD Materials Research and Technology, Eindhoven (Netherlands)

2001-09-01

In most European countries the limit for fluoride emission in ceramic kiln flue gases is set at 5 mg HF/m{sup 3} flue gas. In cooperation with Royal Mosa, Royal Sphinx, Gasunie in the Netherlands and Sacmi, Italy, a roller kiln has been developed which can operate below the fore-mentioned limit. Also, a flue gas cleaning device is not necessary. 4 refs.

Applied CATIA Secondary Development to Parametric Design of Active Magnetic Bearing

Directory of Open Access Journals (Sweden)

Zhang Li

2016-01-01

Full Text Available Based on the properties of active magnetic bearing, the electromagnetic parameters and structure parameters are analyzed, parametric design method is introduced to study the structure of active magnetic bearing. Through a program personalization process that is in accordance with active magnetic bearing is established. Personalization process aims to build the parametric model of active magnetic bearings and component library by use of CATIA secondary development. Component library is to build assembly model for a multiple degree of freedom magnetic bearing system. Parametric design is a method that provides the direction for its structural design.

A feasibility assessment of magnetic bearings for free-piston Stirling space power converters

Science.gov (United States)

Curwen, Peter W.; Rao, Dantam K.; Wilson, Donald R.

1992-01-01

This report describes a design and analysis study performed by Mechanical Technology Incorporated (MTI) under NASA Contract NAS3-26061. The objective of the study was to assess the feasibility and efficacy of applying magnetic bearings to free-piston Stirling-cycle power conversion machinery of the type currently being evaluated for possible use in long-term space missions. The study was performed for a 50-kWe Reference Stirling Space Power Converter (RSSPC) system consisting of two 25-kWe free-piston Stirling engine modules. Two different versions of the RSSPC engine modules have been defined under NASA Contract NAS3-25463. These modules currently use hydrostatic gas bearings to support the reciprocating displacer and power piston assemblies. Results of this study show that active magnetic bearings of the attractive electromagnetic type are technically feasible for RSSPC application provided that wire insulation with 60,000-hr life capability at 300 C can be developed for the bearing coils. From a design integration standpoint, both versions of the RSSPC were found to be conceptually amenable to magnetic support of the power piston assembly. However, only one version of the RSSPC was found to be amendable to magnetic support of the displacer assembly. Unacceptable changes to the basic engine design would be required to incorporate magnetic displacer bearings into the second version. Complete magnetic suspension of the RSSPC can potentially increase overall efficiency of the Stirling cycle power converter by 0.53 to 1.4 percent (0.15 to 0.4 efficiency points). Magnetic bearings will also overcome several operational concerns associated with hydrostatic gas bearing systems. However, these advantages are accompanied by a 5 to 8 percent increase in specific mass of the RSSPC, depending on the RSSPC version employed. Additionally, magnetic bearings are much more complex, both mechanically and particularly electronically, than hydrostatic bearings. Accordingly, long

A Comparative Experimental Study on Identification of Defect Severity in Rolling Element Bearings using Acoustic Emission and Vibration Analysis

Directory of Open Access Journals (Sweden)

V.V. Rao

2015-06-01

Full Text Available This paper describes the comparison between Vibration Analysis (VA and Acoustic Emission (AE method to predict the defect severity in rolling element bearings with respect to the gradual increase of defect size. In bearing fault diagnosis vibration based methods are very popular, but the signals acquired by its transducers from the bearings are distorted by other faults and mechanical noise from the equipment. Vibration based methods are effective when the defect in the bearings has already become severe. AE is a non destructive testing (NDT technique used in structural health monitoring and its application for bearing defect diagnosis is gaining momentum as an alternate diagnostic tool because of its inherent high signal-to-noise-ratio (SNR. A bearing test rig was designed and set up to study the various defects in rolling element bearings in real environment. In earlier cases, though the researchers studied on different types of seeded defects with random sizes, they could not ascertain the correlation between their defect sizes and the vibration amplitude. The experimental investigation reported in this paper is centered on seeded defect of same type with gradual increase of its size on outer race of radially loaded cylindrical roller bearings and running the defective bearing at different speeds and loads. Data acquired through AE & vibration probes simultaneously for better diagnosis. Comparisons between AE and VA over a range of speed and load conditions at gradual increase of defect size are presented and from them it is concluded that AE method is superior to identify the severity of defect.

Analysis of Space Station Centrifuge Rotor Bearing Systems: A Case Study

Science.gov (United States)

Poplawski, Joseph V.; Loewenthal, Stuart H.; Oswald, Fred B.; Zaretsky, Erwin V.; Morales, Wilfredo; Street, Kenneth W., Jr.

2014-01-01

A team of NASA bearing and lubrication experts was assembled to assess the risk for the rolling-element bearings used in the International Space Station (ISS) centrifuge rotor (CR) to seize or otherwise fail to survive for the required 10-year life. The CR was designed by the Japan Aerospace Exploration Agency and their subcontractor, NEC Toshiba Space Systems, Ltd. (NTSpace). The NASA team performed a design audit for the most critical rolling-element bearing systems and reviewed the lubricant selected. There is uncertainty regarding the ability of the Braycote 601 grease (Castrol Limited) to reliably provide the 10-year continuous life required without relubrication of the system. The fatigue life of the Rotor Shaft Assembly (RSA) spring loaded face-to-face mount at a 99-percent probability of survival (L1 life) for the ball bearing set was estimated at 700 million hours and the single ball bearing (Row 3) at 58 million hours. These lives satisfy the mission requirements for fatigue. Rolling-element seizure tests on the RSA and fluid slip joint bearings were found unlikely to stop the centrifuge, which can cause damage to the ISS structure. The spin motor encoder duplex angular-contact ball bearings have a hard preload and a large number of small balls have the highest risk of failure. These bearings were not tested for seizure even though they are less tolerant to debris or internal clearance reductions.

Usefulness of extracorporeal membrane oxygenation using double roller pumps in a low body weight newborn: A novel strategy for mechanical circulatory support in an infant

Directory of Open Access Journals (Sweden)

Keisuke Nakanishi

2016-01-01

Full Text Available Extracorporeal membrane oxygenation (ECMO with a centrifugal pump requires a certain flow rate; therefore, its application for low body weight infants is frequently accompanied by oxygenator membrane malfunction and/or inadequate perfusion. To prevent low-flow associated complications, we report a case in which a novel system of dual roller pumps was used. A baby girl with a body mass index 0.25 m 2 , who experienced difficulty weaning from cardiopulmonary bypass after a Norwood-like operation, required an ECMO. Concerns for the tube lifespan reduction due to roller pump friction led to the use of a double roller pump circulation. The termination of ECMO during tube exchange is not needed, because circulation is maintained by another roller pump. The novel strategy of ECMO with double roller pumps will allow low perfusion rate to provide adequate circulatory support for low body weight patients.

Pin and roller attachment system for ceramic blades

Science.gov (United States)

Shaffer, J.E.

1995-07-25

In a turbine, a plurality of blades are attached to a turbine wheel by way of a plurality of joints which form a rolling contact between the blades and the turbine wheel. Each joint includes a pin and a pair of rollers to provide rolling contact between the pin and an adjacent pair of blades. Because of this rolling contact, high stress scuffing between the blades and the turbine wheel reduced, thereby inhibiting catastrophic failure of the blade joints. 3 figs.

Conical Magnetic Bearings Developed for Active Stall Control in Gas Turbine Engines

Science.gov (United States)

Trudell, Jeffrey J.; Kascak, Albert F.; Provenza, Andrew J.; Buccieri, Carl J.

2004-01-01

replaces the ball bearing in front of the compressor, and the second replaces the roller bearing behind the burner. The rig was made operational to 10,000 rpm under Smart Efficient Components funding, and both position and current adaptive vibration control have been demonstrated. Upon program completion, recommendations will be made as to the efficacy of the conical magnetic bearing for active stall control.

Liikluseksperimendis edestas roller tsiklit ja teisi osalejaid : “2 vs 4″

Index Scriptorium Estoniae

2010-01-01

12. mail toimus Tallinnas keskkonnasõbraliku motonäituse MoMa raames eksperiment, milles osalesid jalgratas, elektriroller, roller, mootorratas ja auto. Marsruudil Miidurand-Nõmme üritati hommikuses liikluses välja selgitada, milline neist sõiduvahendest kõige edukamalt toime tuleb

Faults Diagnostics of Railway Axle Bearings Based on IMF’s Confidence Index Algorithm for Ensemble EMD

Science.gov (United States)

Yi, Cai; Lin, Jianhui; Zhang, Weihua; Ding, Jianming

2015-01-01

As train loads and travel speeds have increased over time, railway axle bearings have become critical elements which require more efficient non-destructive inspection and fault diagnostics methods. This paper presents a novel and adaptive procedure based on ensemble empirical mode decomposition (EEMD) and Hilbert marginal spectrum for multi-fault diagnostics of axle bearings. EEMD overcomes the limitations that often hypothesize about data and computational efforts that restrict the application of signal processing techniques. The outputs of this adaptive approach are the intrinsic mode functions that are treated with the Hilbert transform in order to obtain the Hilbert instantaneous frequency spectrum and marginal spectrum. Anyhow, not all the IMFs obtained by the decomposition should be considered into Hilbert marginal spectrum. The IMFs’ confidence index arithmetic proposed in this paper is fully autonomous, overcoming the major limit of selection by user with experience, and allows the development of on-line tools. The effectiveness of the improvement is proven by the successful diagnosis of an axle bearing with a single fault or multiple composite faults, e.g., outer ring fault, cage fault and pin roller fault. PMID:25970256

Analysis of bearing stiffness variations, contact forces and vibrations in radially loaded double row rolling element bearings with raceway defects

Science.gov (United States)

Petersen, Dick; Howard, Carl; Sawalhi, Nader; Moazen Ahmadi, Alireza; Singh, Sarabjeet

2015-01-01

A method is presented for calculating and analyzing the quasi-static load distribution and varying stiffness of a radially loaded double row bearing with a raceway defect of varying depth, length, and surface roughness. The method is applied to ball bearings on gearbox and fan test rigs seeded with line or extended outer raceway defects. When balls pass through the defect and lose all or part of their load carrying capacity, the load is redistributed between the loaded balls. This includes balls positioned outside the defect such that good raceway sections are subjected to increased loading when a defect is present. The defective bearing stiffness varies periodically at the ball spacing, and only differs from the good bearing case when balls are positioned in the defect. In this instance, the stiffness decreases in the loaded direction and increases in the unloaded direction. For an extended spall, which always has one or more balls positioned in the defect, this results in an average stiffness over the ball spacing period that is lower in the loaded direction in comparison to both the line spall and good bearing cases. The variation in bearing stiffness due to the defect produces parametric excitations of the bearing assembly. The qualitative character of the vibration response correlates to the character of the stiffness variations. Rapid stiffness changes at a defect exit produce impulses. Slower stiffness variations due to large wavelength waviness features in an extended spall produce low frequency excitation which results in defect components in the velocity spectra. The contact forces fluctuate around the quasi-static loads on the balls, with rapid stiffness changes producing high magnitude impulsive force fluctuations. Furthermore, it is shown that analyzing the properties of the dynamic model linearized at the quasi-static solutions provides greater insight into the time-frequency characteristics of the vibration response. This is demonstrated by relating

Roller and Centrifugal Pumps: A Retrospective Comparison of Bleeding Complications in Extracorporeal Membrane Oxygenation.

Science.gov (United States)

Halaweish, Ihab; Cole, Adam; Cooley, Elaine; Lynch, William R; Haft, Jonathan W

2015-01-01

Centrifugal pumps are increasingly used for extracorporeal membrane oxygenation (ECMO) rather than roller pumps. However, shear forces induced by these types of continuousflow pumps are associated with acquired von Willebrand factor deficiency and bleeding complications. This study was undertaken to compare adverse bleeding complications with the use of centrifugal and roller pumps in patients on prolonged ECMO support. The records of all adult ECMO patients from June 2002 to 2013 were retrospectively reviewed using the University of Michigan Health System database and the Extracorporeal Life Support Organization registry, focusing on patients supported for at least 5 days. Ninety-five ECMO patients met criteria for inclusion (48 roller vs. 47 centrifugal pump). Indications included pulmonary (79%), cardiac (15%), and extracorporeal cardiopulmonary resuscitation (6%), without significant difference between the two groups. Despite lower heparin anticoagulation (10.9 vs. 13.7 IU/kg/hr) with centrifugal pumps, there was a higher incidence of nonsurgical bleeding (gastrointestinal, pulmonary, and neurological) in centrifugal pump patients (26.1 vs. 9.0 events/1,000 patient-days, p = 0.024). In conclusion, in our historical comparison, despite reduced anticoagulation, ECMO support using centrifugal pumps was associated with a higher incidence of nonsurgical bleeding. The mechanisms behind this are multifactorial and require further investigation.

Visualizing asphalt roller trajectories in context: acquiring, processing, and representing sensor readings

NARCIS (Netherlands)

Vasenev, Alexandr

2015-01-01

The asphalt compaction process relies heavily on the skills and knowledge of roller operators who act alongside other stakeholders involved in asphalt paving. It is essential that these construction specialists: (1) are adequately informed about the initial temperature distribution of the asphalt

Kinematics of roller chain drives - Exact and approximate analysis

DEFF Research Database (Denmark)

Fuglede, Niels; Thomsen, Jon Juel

2016-01-01

An exact and approximate kinematic analysis of a roller chain drive modeled as a four-bar mechanism is presented. The span connects the sprockets such that they rotate in the same direction, and the sprocket size, number of teeth, and shaft center distance can be arbitrary. The driven sprocket...... to be very good agreement. All together this gives new insights into the characteristics of chain drive kinematics and the influence of main design parameters....

Roller Testing to Mimic Damage of the ISS SARJ Ring and Durability Test to Simulate Fifteen Years of SARJ Operation Using the Damaged Surface

Science.gov (United States)

Krantz, Timothy L.; Elchert, Justin P.; DellaCorte, Christopher; Dube, Michael J.

2016-01-01

The International Space Station's starboard Solar Alpha Rotary Joint (SARJ) experienced a breakdown of the joint's race ring surface. The starboard SARJ mechanism was cleaned and lubricated with grease. To provide some guidance on the expected behavior of the damaged SARJ ring with continued operations, experiments were conducted using rollers and a vacuum roller test rig. The approach of the experimental work involved three main steps: (1) initiate damage using conditions representative of the SARJ with inadequate lubrication; (2) propagate the damage by operating the test rollers without lubrication; and (3) assess the durability of the roller by testing to simulate the equivalent of 15 years of SARJ operation on the damaged surface assuming adequate grease lubrication. During the rig testing, additional and/or replacement grease was introduced at regular intervals to maintain good lubrication in the rig. The damage to the nitride layer continued even after application of grease. The grease lubrication proved to be effective for limiting the value of the axial force that can be developed. Limiting the axial force on the SARJ mechanism is important since the larger the axial force the more concentrated the load pressure becomes on the blend-radius location on the SARJ roller. After the testing simulating 15 years of SARJ operations, the wear depths were the order of 0.2 mm for the nitrided 15-5 roller and the order of 0.06 mm for the mating 440C roller. Metallographic inspections were done to search for indications of impending fatigue or other fracture indications that might eventually propagate and cause structural failure. There were no indications or features found that could eventually compromise structural integrity.

Superconducting-electromagnetic hybrid bearing using YBCO bulk blocks for passive axial levitation

Science.gov (United States)

Nicolsky, R.; de Andrade, R., Jr.; Ripper, A.; David, D. F. B.; Santisteban, J. A.; Stephan, R. M.; Gawalek, W.; Habisreuther, T.; Strasser, T.

2000-06-01

A superconducting/electromagnetic hybrid bearing has been designed using active radial electromagnetic positioning and a superconducting passive axial levitator. This bearing has been tested for an induction machine with a vertical shaft. The prototype was conceived as a four-pole, two-phase induction machine using specially designed stator windings for delivering torque and radial positioning simultaneously. The radial bearing uses four eddy-current sensors, displaced 90° from each other, for measuring the shaft position and a PID control system for feeding back the currents. The stator windings have been adapted from the ones of a standard induction motor. The superconducting axial bearing has been assembled with commercial NdFeB permanent magnets and a set of seven top-seeded-melt-textured YBCO large-grain cylindrical blocks. The bearing set-up was previously simulated by a finite element method for different permanent magnet-superconductor block configurations. The stiffness of the superconducting axial bearing has been investigated by measuring by a dynamic method the vertical and transversal elastic constants for different field cooling processes. The resulting elastic constants show a linear dependence on the air gap, i.e. the clearance between the permanent magnet assembly and the set of superconducting large-grain blocks, which is dependent on cooling distance.

Lake Robertson hydroelectric project. Construction of a roller compacted concrete dam

Energy Technology Data Exchange (ETDEWEB)

Labelle, M.; Robitaille, F. [Hydro-Quebec, Montreal, PQ (Canada)

1995-12-31

Construction of the Lake Robertson hydroelectric project on Quebec`s Lower North Shore was discussed in detail. The dam and powerhouse, located on the HaHa River, consists of a 134 m long concrete gravity dam, and a 21 MW powerhouse with two 69 kV transmission lines and four substations. The climate, terrain, and geography of the region, all of them characterized as severe, and the logistics of construction of the dam and power lines, aggravated by the isolation and severe conditions at the site, were described. The roller compacted concrete design and construction were noted, and justification for a concrete dam over an earth-fill dam was provided. Economics, properties, and composition of the roller compacted concrete (RCC) were examined, and control test results for the RCC concrete were provided. The use of RCC for the Lake Robertson development was described as successful in terms of the quality, watertightness, and completion time. The experience gained by the participants will make it possible to offer RCC as an alternative on various other projects. 2 figs.

The two-dimensional cutting stock problem within the roller blind production process

NARCIS (Netherlands)

E.R. de Gelder; A.P.M. Wagelmans (Albert)

2007-01-01

textabstractIn this paper we consider a two-dimensional cutting stock problem encountered at a large manufacturer of window covering products. The problem occurs in the production process of made-to-measure roller blinds. We develop a solution method that takes into account the characteristics of

Diagnostics of the Technical State of Bearings of Mining Machines Base Assemblies

Science.gov (United States)

Gerike, Boris L.; Mokrushev, Andrey A.

2017-10-01

The article reviews the methods of technical diagnostics of equipment used during maintenance of mining machines in accordance with their actual technical state, and considers the basics of vibration parameters measuring. The classification of existing methods for diagnosing the technical condition of rolling bearings is given. The advantages and disadvantages of these methods are considered. The main defects of rolling bearings arising during manufacturing, transportation, storage, and operation are considered.

Failure analysis of the ball bearings of dental air turbine handpieces.

Science.gov (United States)

Wei, M; Dyson, J E; Darvell, B W

2013-12-01

The aim of this study was to identify the nature and causes of deterioration and failure in dental handpiece ball bearings and thus provide guidance for clinical handling for service longevity. The bearings of 36 turbine assemblies were dismantled for visual inspection, documented using a digital camera, and examined using scanning electron microscopy, as appropriate. For the metal parts of the ball bearing assembly, defects observed were mainly wear arising from the running load and corrosion. This was in the form of scratches and discoloured circumferential bands on the balls, and dull or worn surfaces extending around the circumference of the raceways. Cage damage including cracking, fracture, surface rubbing and distortion occurred, in varying degrees, in every failed turbine. Dental ball bearing failure modes have been identified. Cumulative effects of damage from corrosion and mechanical factors lead to handpiece deterioration. The cage was found to be very vulnerable to damage, and this may be the key limitation on bearing lifetime. Autoclaving may contribute to that, as it does to corrosion in the absence of adequate lubrication, but this seems to be minor in comparison to the effects of abuse. There is no justification for failing to observe usage and sterilization instructions. © 2013 Australian Dental Association.

Self-assembled containers based on extended tetrathiafulvalene.

Science.gov (United States)

Bivaud, Sébastien; Goeb, Sébastien; Croué, Vincent; Dron, Paul I; Allain, Magali; Sallé, Marc

2013-07-10

Two original self-assembled containers constituted each by six electroactive subunits are described. They are synthesized from a concave tetratopic π-extended tetrathiafulvalene ligand bearing four pyridyl units and cis-M(dppf)(OTf)2 (M = Pd or Pt; dppf = 1,1'-bis(diphenylphosphino)ferrocene; OTf = trifluoromethane-sulfonate) complexes. Both fully characterized assemblies present an oblate spheroidal cavity that can incorporate one perylene molecule.

Preliminary evaluation of steel-roller round baler for woody biomass baling

Science.gov (United States)

B. J. Stokes; D. L. Sirois; S. L. Woodfin

1987-01-01

A round hay baler with little modification was used to bale small-diameter, crushed trees. The trees had been crushed using a series of compression rollers. Bale cores had to be developed by hand before the baler became self-feeding. Windrowed material was packed off the ground by the baler system after a core had been developed.

Acceleration in One, Two, and Three Dimensions in Launched Roller Coasters

Science.gov (United States)

Pendrill, Ann-Marie

2008-01-01

During a roller coaster ride, the body experiences acceleration in three dimensions. An accelerometer can measure and provide a graph of the forces on the body during different parts of a ride. To couple the experience of the body to pictures of the ride and an analysis of data can contribute to a deeper understanding of Newton's laws. This…

Corrective action decision document for the Roller Coaster Lagoons and North Disposal Trench (Corrective Action Unit Number 404)

International Nuclear Information System (INIS)

1997-01-01

The North Disposal Trench, located north of the eastern most lagoon, was installed in 1963 to receive solid waste and construction debris from the Operation Roller Coaster man camp. Subsequent to Operation Roller Coaster, the trench continued to receive construction debris and range cleanup debris (including ordnance) from Sandia National Laboratories and other operators. A small hydrocarbon spill occurred during Voluntary Corrective Action (VCA) activities (VCA Spill Area) at an area associated with the North Disposal Trench Corrective Action Site (CAS). Remediation activities at this site were conducted in 1995. A corrective action investigation was conducted in September of 1996 following the Corrective Action Investigation Plan (CAIP); the detailed results of that investigation are presented in Appendix A. The Roller Coaster Lagoons and North Disposal Trench are located at the Tonopah Test Range (TTR), a part of the Nellis Air Force Range, which is approximately 225 kilometers (140 miles) northwest of Las Vegas, Nevada, by air

The influence of increased distal loading on metabolic cost, efficiency, and kinematics of roller ski skating.

Science.gov (United States)

Bolger, Conor M; Bessone, Veronica; Federolf, Peter; Ettema, Gertjan; Sandbakk, Øyvind

2018-01-01

The purpose of the present study was to examine the influence of increased loading of the roller ski on metabolic cost, gross efficiency, and kinematics of roller ski skating in steep and moderate terrain, while employing two incline-specific techniques. Ten nationally ranked male cross-country skiers were subjected to four 7-minute submaximal intervals, with 0, 0.5, 1.0, and 1.5 kg added beneath the roller-ski in a randomized order. This was done on two separate days, with the G2 skating at 12% incline and 7 km/h speed and G3 skating at 5% incline and 14 km/h speed, respectively. At 12% incline, there was a significant increase in metabolic rate and a decrease in gross efficiency with added weight (P0.05). No changes in cycle characteristics were observed between the different ski loadings at either incline, although the lateral and vertical displacements of the foot/skis were slightly altered at 12% incline with added weight. In conclusion, the present study demonstrates that increased loading of the ski increases the metabolic cost and reduces gross efficiency during steep uphill roller skiing in G2 skating, whereas no significant effect was revealed when skating on relatively flat terrain in G3. Cycle characteristics remained unchanged across conditions at both inclines, whereas small adjustments in the displacement of the foot coincided with the efficiency changes in uphill terrain. The increased RPE values with added ski-weight at both inclines indicates that other factors than those measured here could have influenced effort and/or fatigue when lifting a heavier ski.

Axial force in a superconductor magnet journal bearing

Science.gov (United States)

Postrekhin, E.; Chong, Wang; Ki Bui, Ma; Chen, Quark; Chu, Wei-Kan

Using superconductors and magnets, a journal bearing could be made from a permanent magnet cylinder in a superconductor ring. We have assembled a prototype superconductor magnet journal bearing of this configuration, and investigated the behavior of the axial force that it can provide. We have put together a numerical model of the interaction between the permanent magnet and the superconductor that is capable of describing these experimental results semi-quantitatively. Combining direct experimental measurements and using the numerical models proposed, we have achieved a qualitative understanding of the behavior of the axial force and its relationship of to the dimensions of the magnet and material quality such as the homogeneity of the superconductor that constitute the bearing.

An optimum design on rollers containing the groove with changeable inner diameter based on response surface methodology

Directory of Open Access Journals (Sweden)

Xi Zhao

2016-05-01

Full Text Available In order to realize the precision plastic forming of the revolving body component with changeable wall thickness, a kind of roller containing grooves with changeable inner diameter is put forward, as the forming mould of the technology of rolling-extrusion. Specifically, first, the arc length of the groove in the roller is designed according to the prediction on the forward slip value during the process of forming, to make accurate control of the actual length of the forming segments; then, to obtain better parameters of the roller structure, a second-order response surface model combining finite element numerical simulation and response surface methodology was put forward, taking the factor of forming uniformity as evaluation index. The result of the experiment shows that, for the formed component, not only the size can meet the needs but also each mechanical property index can be greatly improved, which verify the rationality of the forward slip model and the structural parameter of the optimum model based on the response surface methodology.

Control rod guide tube assemblies

International Nuclear Information System (INIS)

Jabsen, F.S.

1979-01-01

A nuclear fuel assembly including sleeves telescoped over end portions of control rod guide tubes which bear against internal shoulders of the sleeves. Upper ends of the sleeves protrude beyond a control rod guide tube spider and are locked in place by means of a resilient cellular lattice or lock that is seated in mating grooves in the outer surfaces of the sleeves. A grapple is provided for disengaging the entire lock structure spider and associated washers, springs and a grill from the end of the fuel assembly in order to enable these components to be removed and subsequently replaced on the fuel assembly after inspection and repair. (UK)

Evaluation Standard for Safety Coefficient of Roller Compacted Concrete Dam Based on Finite Element Method

Directory of Open Access Journals (Sweden)

Bo Li

2014-01-01

Full Text Available The lack of evaluation standard for safety coefficient based on finite element method (FEM limits the wide application of FEM in roller compacted concrete dam (RCCD. In this paper, the strength reserve factor (SRF method is adopted to simulate gradual failure and possible unstable modes of RCCD system. The entropy theory and catastrophe theory are used to obtain the ultimate bearing resistance and failure criterion of the RCCD. The most dangerous sliding plane for RCCD failure is found using the Latin hypercube sampling (LHS and auxiliary analysis of partial least squares regression (PLSR. Finally a method for determining the evaluation standard of RCCD safety coefficient based on FEM is put forward using least squares support vector machines (LSSVM and particle swarm optimization (PSO. The proposed method is applied to safety coefficient analysis of the Longtan RCCD in China. The calculation shows that RCCD failure is closely related to RCCD interface strength, and the Longtan RCCD is safe in the design condition. Considering RCCD failure characteristic and combining the advantages of several excellent algorithms, the proposed method determines the evaluation standard for safety coefficient of RCCD based on FEM for the first time and can be popularized to any RCCD.

Design and fabrication of gas bearings for Brayton cycle rotating unit

Science.gov (United States)

Frost, A.; Tessarzik, J. M.; Arwas, E. B.; Waldron, W. D. (Editor)

1973-01-01

Analysis, design, and testing of two types of pivoted pad journal bearings and a spiral-grooved thrust bearing suitable for direct installation into the NASA 2 to 15 KW Brayton Cycle Rotating Unit (BRU) have been accomplished. Both types of tilting pad bearing assemblies are of the preloaded type, consisting of three pads with one pad flexibly mounted. One type utilizes a non-conforming pivot, while the other replaces the conventional spherical pivot with a cruciform flexible member. The thrust bearing is flexure mounted to accommodate static machine mislinement. Test results indicate that both types of journal bearings should satisfy the requirements imposed by the BRU. Hydrostatic tests of the spiral-grooved thrust bearing showed it to be free of pneumatic hammer with as many as 24 orifices over the BRU pressure and load range.

77 FR 52682 - Tapered Roller Bearings and Parts Thereof, Finished and Unfinished, From the People's Republic of...

Science.gov (United States)

2012-08-30

....80.80.\\5\\ Although the HTSUS item numbers are provided for convenience and customs purposes, the... Trend Engineering Ltd.'s Wheel Hub Assemblies,'' dated April 18, 2011 (finding New Trend Engineering...

Experimental studies in Ultrasonic Pulse Velocity of roller compacted concrete pavement containing fly ash and M-sand

Directory of Open Access Journals (Sweden)

S. Krishna Rao

2016-07-01

Full Text Available This paper presents the experimental investigation results of Ultrasonic Pulse Velocity (UPV tests conducted on roller compacted concrete pavement (RCCP material containing Class F fly ash of as mineral admixture. River sand, M-sand and combination of M-sand and River sand are used as fine aggregate in this experimental work. Three types of fly ash roller compacted concrete mixes are prepared using above three types of fine aggregates and they are designated as Series A (River sand, Series B (manufactured sand and Series C (combination of River sand and M-sand. In each series the fly ash content in place of cement is varied from 0% to 60%. In each series and for different ages of curing (i.e 3, 7, 28 and 90 days forty two cube specimens are cast and tested for compressive strength and UPV. The UPV results of fly ash containing roller compacted concrete pavement (FRCCP show lower values at all ages from 3 days to 90 days in comparison with control mix concrete (0% fly ash in all mixes. However, it is also observed that Series B and C mixes containing fly ash show better results in UPV values, compressive strength and Dynamic Elastic Modulus in comparison to Series A mixes with fly ash. Relationships between compressive strength of FRCCP and UPV and Dynamic Elastic Modulus are proposed for all series mixes. A new empirical equation is proposed to determine the Dynamic Elastic Modulus of FRCCP. Keywords: Compressive strength, Dynamic Elastic Modulus, Fly ash, Roller compacted concrete pavement, Ultrasonic Pulse Velocity

Fatigue damage of steel components

DEFF Research Database (Denmark)

Fæster, Søren; Zhang, Xiaodan; Huang, Xiaoxu

2014-01-01

Railway rails and the inner ring in roller bearings in wind turbines are both experiencing steel-to-steel contact in small areas with huge loads resulting in extremely high stresses in the base materials......Railway rails and the inner ring in roller bearings in wind turbines are both experiencing steel-to-steel contact in small areas with huge loads resulting in extremely high stresses in the base materials...

Planetary Load Sharing in Three-Point Mounted Wind Turbine Gearboxes: A Design and Test Comparison

Energy Technology Data Exchange (ETDEWEB)

Keller, Jonathan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Guo, Yi [National Renewable Energy Lab. (NREL), Golden, CO (United States); Zhang, Zhiwei [Romax InSight, Nottingham, (United Kingdom); Lucas, Doug [The Timken Company, Jackson Township, OH (United States)

2017-04-06

This work compares the planetary load-sharing characteristics of wind turbine gearboxes supported by cylindrical roller bearings (CRBs) and preloaded tapered roller bearings (TRBs) when subjected to rotor moments. Planetary bearing loads were measured in field-representative dynamometer tests and compared to loads predicted by finite-element models. Preloaded TRBs significantly improved load sharing. In pure torque conditions, the upwind planet bearing load in the gearbox with preloaded TRBs was only 14% more than the assumed load compared to 47% more for the gearbox with CRBs. Consequently, the predicted fatigue life of the complete set of planetary bearings for the gearbox with preloaded TRBs is 3.5 times greater than that of the gearbox with CRBs.

The Influence of Pressure Distribution on the Maximum Values of Stress in FEM Analysis of Plain Bearings

Directory of Open Access Journals (Sweden)

Vasile Cojocaru

2016-12-01

Full Text Available Several methods can be used in the FEM studies to apply the loads on a plain bearing. The paper presents a comparative analysis of maximum stress obtained for three loading scenarios: resultant force applied on the shaft – bearing assembly, variable pressure with sinusoidal distribution applied on the bearing surface, variable pressure with parabolic distribution applied on the bearing surface.

Superconductor bearings, flywheels and transportation

International Nuclear Information System (INIS)

Werfel, F N; Floegel-Delor, U; Rothfeld, R; Riedel, T; Goebel, B; Wippich, D; Schirrmeister, P

2012-01-01

This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS–FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN 2 . More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.

Study on the Effect of Steel Wheel and Ground on Single Steel Vibratory Roller

Science.gov (United States)

Li, Jiabo; You, Guanghui; Qiao, Jiabin; Ye, Min; Guo, Jin; Zhang, Hongyang

2018-03-01

In the compacting operation of single drum vibratory roller, the forces acting on the foundation of drum include the weight of the drum, the weight of the frame, the exciting force and so on. Based on the theoretical study of ground mechanics, this paper analyzes and calculates the forces acting on the steel wheel and the ground, and obtains the distribution of the laminar stress in the ground when the working plane vibrates. Derive the formula of dynamic compressive stress and static compressive stress in the foundation during vibration compaction. Through the compaction test of the soil trough of 20T single drum roller, the compressive stress data of the soil hydraulic field are obtained. The data of the dynamic compressive stress and the static compressive stress of each layer during the third compaction are obtained, and the theoretical research is verified.

The construction design of ball bearings used in the control rod driving mechanisms of PWRs

International Nuclear Information System (INIS)

Leng Chengmu; Huang Chongming; Chen Jianting.

1986-01-01

According to the operation conditions of ball bearings used in the control rod driving mechanisms of PWRs, this paper has analysed and discussed the problems that must be taken into account in the construction design of this ball bearing. It includes: a discussion about the reasonable selection of construction parameters of the bearing, deduction of the relationship between bearing clearance and contact angle, and the emphasis on the significance of assembling accuracy and torque measurement in the assurance of operational performance of the bearings. These experiences may be somewhat valuable for the design and application of this kind of ball bearing

Development of procedures for calculating stiffness and damping of elastomers in engineering applications, part 7

Science.gov (United States)

Rieger, A.; Zorzi, E.

1980-01-01

An elastomer shear damper was designed, tested, and compared with the performance of the T 55 power turbine supported on the production engine roller bearing support. The Viton 70 shear damper was designed so that the elastomer damper could be interchanged with the production T 55 power turbine roller bearing support. The results show that the elastomer sheer dampener permitted stable operation of the power turbine to the maximum operating speed of 16,000 rpm.

Ball Bearings Equipped for In Situ Lubrication on Demand

Science.gov (United States)

Marchetti, Mario; Jones, William R., Jr.; Pepper, Stephen V.; Jansen, Mark; Predmore, Roamer

2005-01-01

In situ systems that provide fresh lubricants to ball/race contacts on demand have been developed to prolong the operational lives of ball bearings. These systems were originally intended to be incorporated into ball bearings in mechanisms that are required to operate in outer space for years, in conditions in which lubricants tend to deteriorate and/or evaporate. These systems may also be useful for similarly prolonging bearing lifetimes on Earth. Reservoirs have been among the means used previously to resupply lubricants. Lubricant- resupply reservoirs are bulky and add complexity to bearing assemblies. In addition, such a reservoir cannot be turned on or off as needed: it supplies lubricant continuously, often leading to an excess of lubricant in the bearing. A lubricator of the present type includes a porous ring cartridge attached to the inner or the outer ring of a ball bearing (see Figure 1). Oil is stored in the porous cartridge and is released by heating the cartridge: Because the thermal expansion of the oil exceeds that of the cartridge, heating causes the ejection of some oil. A metal film can be deposited on a face of the cartridge to serve as an electrical-resistance heater. The heater can be activated in response to a measured increase in torque that signals depletion of oil from the bearing/race contacts. Because the oil has low surface tension and readily wets the bearing-ring material, it spreads over the bearing ring and eventually reaches the ball/race contacts. The Marangoni effect (a surface-tension gradient associated with a temperature gradient) is utilized to enhance the desired transfer of lubricant to the ball/race contacts during heating. For a test, a ball bearing designed for use at low speed was assembled without lubricant and equipped with a porous-ring lubricator, the resistance heater of which consumed a power of less than 1 W when triggered on by a torque-measuring device. In the test, a load of 20 lb (.89 N) was applied and the

Rereading "The Jack-Roller:" Hidden Histories in Sociology and Social Work

Science.gov (United States)

Shaw, Ian

2009-01-01

I revisit one of the iconic Chicago School studies, Clifford Shaw's "The Jack-Roller". A naive reading of Shaw's book leaves the reader with a sense of having been inducted into a melange of what we now know as "sociology" and "social work," but which to Shaw seems a coherent stance. I suggest that this is close to the heart of how things were,…

Experiments on the Porch Swing Bearing of Michelson Interferometer for Low Resolution FTIR

OpenAIRE

Tuomas Välikylä; Jyrki Kauppinen

2013-01-01

Porch swing bearing for the linear motion of the mirror in Michelson interferometer for mid-infrared low resolution Fourier transform spectrometer was studied experimentally using the modulation depth of the collimated laser beam. The mirror tilting was measured to be lower than 5 μrad over 3 mm mirror travel using two different bearings assemblies. Additionally, the manufacturing tolerances of the bearing type were proved to be loose enough not to limit the interferometer application. These ...

Stochastic Resonance algorithms to enhance damage detection in bearing faults

Directory of Open Access Journals (Sweden)

Castiglione Roberto

2015-01-01

Full Text Available Stochastic Resonance is a phenomenon, studied and mainly exploited in telecommunication, which permits the amplification and detection of weak signals by the assistance of noise. The first papers on this technique are dated early 80 s and were developed to explain the periodically recurrent ice ages. Other applications mainly concern neuroscience, biology, medicine and obviously signal analysis and processing. Recently, some researchers have applied the technique for detecting faults in mechanical systems and bearings. In this paper, we try to better understand the conditions of applicability and which is the best algorithm to be adopted for these purposes. In fact, to get the methodology profitable and efficient to enhance the signal spikes due to fault in rings and balls/rollers of bearings, some parameters have to be properly selected. This is a problem since in system identification this procedure should be as blind as possible. Two algorithms are analysed: the first exploits classical SR with three parameters mutually dependent, while the other uses Woods-Saxon potential, with three parameters yet but holding a different meaning. The comparison of the performances of the two algorithms and the optimal choice of their parameters are the scopes of this paper. Algorithms are tested on simulated and experimental data showing an evident capacity of increasing the signal to noise ratio.

Self-assembling peptide semiconductors

Science.gov (United States)

Tao, Kai; Makam, Pandeeswar; Aizen, Ruth; Gazit, Ehud

2017-01-01

Semiconductors are central to the modern electronics and optics industries. Conventional semiconductive materials bear inherent limitations, especially in emerging fields such as interfacing with biological systems and bottom-up fabrication. A promising candidate for bioinspired and durable nanoscale semiconductors is the family of self-assembled nanostructures comprising short peptides. The highly ordered and directional intermolecular π-π interactions and hydrogen-bonding network allow the formation of quantum confined structures within the peptide self-assemblies, thus decreasing the band gaps of the superstructures into semiconductor regions. As a result of the diverse architectures and ease of modification of peptide self-assemblies, their semiconductivity can be readily tuned, doped, and functionalized. Therefore, this family of electroactive supramolecular materials may bridge the gap between the inorganic semiconductor world and biological systems. PMID:29146781

Out-of-plane stability of roller bent steel arches – an experimental investigation

NARCIS (Netherlands)

La Poutre, D.B.; Spoorenberg, R.C.; Snijder, H.H.; Hoenderkamp, J.C.D.

2013-01-01

This paper presents an experimental investigation of the elastic-plastic out-of-plane buckling response of roller bent circular steel arches subjected to a single force applied to the crown. The experiments are used to validate a finite element model described in a related paper. A series of 15

Long-Life, Oil-Free Polymeric, Multi-Roller Traction Drives for Planetary Vehicle Surface Exploration, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Multi-roller traction drives have several advantages relative to geared units for aerospace and commercial drive applications. Among these are zero backlash, low...

A Weldability Study of Structural Materials for Manufacturing Bearing Separators

Directory of Open Access Journals (Sweden)

V. S. Drizhov

2016-01-01

Full Text Available The aim is to analyze the possibility for using the 08YUT steel separator tape to manufacture separators, which are to be further applied to the bearing assembly via projection welding.Reliability of rolling bearings is determined by many factors such as surface quality of balls and rings and assembly precision, including the seal strength of hemiseparators.The technology based on the double-pulsed condenser projection welding belongs to one of the most efficient technologies to provide the assembly of bearing, for it allows welding of separator simultaneously in all currents. The paper shows that the required condition to assure high reliability of the bearing is induastial development and implementation of an effective and positive quality control system, which will reduce the probability of damages occurring both when welding and in the course of operation.The work used the static tensile test methods, as well as metallographic analysis.The experimental study used the 08YUT steel hemiseparators. A tape thickness of the hemiseparators was of 1.5mm. The number of simultaneously welded points were 8. The experimental studies of the metal damage of welding joints of the the 08YUT steel separator have shown that with a wide range of the changing welding current and compressed electrode force the quality assurance of welding points at the parent metal level could not be retrieved.The metallographic analysis of the metal damage nature of a welded joint revealed that between the atoms on the surfaces of hemiseparators there are no strong bonds – a bond was formed in the contact zone. This phenomenon leads to reduced tensile seal strength.The study has shown that aluminum and titanium added to the low-carbon steel in order to have a more fine-grained metal structure has a negative effect on the quality of welded joint via projection welding.

Health Assessment of Cooling Fan Bearings Using Wavelet-Based Filtering

Directory of Open Access Journals (Sweden)

Qiang Miao

2012-12-01

Full Text Available As commonly used forced convection air cooling devices in electronics, cooling fans are crucial for guaranteeing the reliability of electronic systems. In a cooling fan assembly, fan bearing failure is a major failure mode that causes excessive vibration, noise, reduction in rotation speed, locked rotor, failure to start, and other problems; therefore, it is necessary to conduct research on the health assessment of cooling fan bearings. This paper presents a vibration-based fan bearing health evaluation method using comblet filtering and exponentially weighted moving average. A new health condition indicator (HCI for fan bearing degradation assessment is proposed. In order to collect the vibration data for validation of the proposed method, a cooling fan accelerated life test was conducted to simulate the lubricant starvation of fan bearings. A comparison between the proposed method and methods in previous studies (i.e., root mean square, kurtosis, and fault growth parameter was carried out to assess the performance of the HCI. The analysis results suggest that the HCI can identify incipient fan bearing failures and describe the bearing degradation process. Overall, the work presented in this paper provides a promising method for fan bearing health evaluation and prognosis.

Advanced Transmission Components Investigation Program. Bearing and Seal Development.

Science.gov (United States)

1980-08-01

perf iot r11cC, aS rrt~iti~f( Chear c. Ini August iof 1977 the Timkert Company of Catnioin, hio, con- tracteif i fai,t I and1)( test 11rr IIV.01Led...LND Figure B - 17. Cup. Rollers and Cage Used a( IDrive End of Shaft 78-5 in Test Setup No. 4 (Sheet I of 2). t)4 ROLLERS CAGE 78-17 Figure B -17. Cup

The selection of flying roller as an effort to increase the power of scooter-matic as the main power of centrifugal pump for fire fighter motor cycle

Science.gov (United States)

Hadi Sutrisno, Himawan

2018-03-01

In densely populated settlements, fires often occur and cause losses. In some instances, the process of the occurrence of fires takes place so quickly that to reduce and avoid the occurrence of a fire disaster effort is required in accordance with the existing environmental condition. Fire fighter motorcycle by using motorcycle scooter-matic is considered suitable as one alternative to combating fire hazard in densely populated residential settlements. The use of motorcycle engines as the driving force of the pump often leads to unstable and not optimum power. Thus, the water spray on the centrifugal pump also becomes not maximum. To increase the engine power at scooter-matic engine idle rotation (700-2000 rpm), then the flying roller replacement with certain mass weight becomes an option. By selecting a 10 to 14 gram flying roller mass, the power analysis using a dynotest engine produces several variations. Of the calculation, the mass of a 14 gram flying roller provides a significant increase in motor power on the upper rotation. Meanwhile, on the lower power rotation using a flying roller with a mass of 10 grams provides an increase in power compared to a standard flying roller on a scooter matic motor engine. As a reference to the use of scooter-matic motor power as the pump power, the result of use of the flying roller with a mass of 10 grams becomes the best option.

Genetic control of biennial bearing in apple

Science.gov (United States)

Guitton, Baptiste; Kelner, Jean-Jacques; Velasco, Riccardo; Gardiner, Susan E.; Chagné, David; Costes, Evelyne

2012-01-01

Although flowering in mature fruit trees is recurrent, floral induction can be strongly inhibited by concurrent fruiting, leading to a pattern of irregular fruiting across consecutive years referred to as biennial bearing. The genetic determinants of biennial bearing in apple were investigated using the 114 flowering individuals from an F1 population of 122 genotypes, from a ‘Starkrimson’ (strong biennial bearer)בGranny Smith’ (regular bearer) cross. The number of inflorescences, and the number and the mass of harvested fruit were recorded over 6 years and used to calculate 26 variables and indices quantifying yield, precocity of production, and biennial bearing. Inflorescence traits exhibited the highest genotypic effect, and three quantitative trait loci (QTLs) on linkage group (LG) 4, LG8, and LG10 explained 50% of the phenotypic variability for biennial bearing. Apple orthologues of flowering and hormone-related genes were retrieved from the whole-genome assembly of ‘Golden Delicious’ and their position was compared with QTLs. Four main genomic regions that contain floral integrator genes, meristem identity genes, and gibberellin oxidase genes co-located with QTLs. The results indicated that flowering genes are less likely to be responsible for biennial bearing than hormone-related genes. New hypotheses for the control of biennial bearing emerged from QTL and candidate gene co-locations and suggest the involvement of different physiological processes such as the regulation of flowering genes by hormones. The correlation between tree architecture and biennial bearing is also discussed. PMID:21963613

Intelligent condition monitoring method for bearing faults from highly compressed measurements using sparse over-complete features

Science.gov (United States)

Ahmed, H. O. A.; Wong, M. L. D.; Nandi, A. K.

2018-01-01

Condition classification of rolling element bearings in rotating machines is important to prevent the breakdown of industrial machinery. A considerable amount of literature has been published on bearing faults classification. These studies aim to determine automatically the current status of a roller element bearing. Of these studies, methods based on compressed sensing (CS) have received some attention recently due to their ability to allow one to sample below the Nyquist sampling rate. This technology has many possible uses in machine condition monitoring and has been investigated as a possible approach for fault detection and classification in the compressed domain, i.e., without reconstructing the original signal. However, previous CS based methods have been found to be too weak for highly compressed data. The present paper explores computationally, for the first time, the effects of sparse autoencoder based over-complete sparse representations on the classification performance of highly compressed measurements of bearing vibration signals. For this study, the CS method was used to produce highly compressed measurements of the original bearing dataset. Then, an effective deep neural network (DNN) with unsupervised feature learning algorithm based on sparse autoencoder is used for learning over-complete sparse representations of these compressed datasets. Finally, the fault classification is achieved using two stages, namely, pre-training classification based on stacked autoencoder and softmax regression layer form the deep net stage (the first stage), and re-training classification based on backpropagation (BP) algorithm forms the fine-tuning stage (the second stage). The experimental results show that the proposed method is able to achieve high levels of accuracy even with extremely compressed measurements compared with the existing techniques.

An Analysis of US Emergency Department Visits From Falls From Skiing, Snowboarding, Skateboarding, Roller-Skating, and Using Nonmotorized Scooters.

Science.gov (United States)

Nathanson, Brian H; Ribeiro, Kara; Henneman, Philip L

2016-07-01

We analyzed the US incidence of emergency department (ED) visits and hospitalizations for falls from skiing, snowboarding, skateboarding, roller-skating, and nonmotorized scooters in 2011. The outcome was hospital admission from the ED. The primary analysis compared pediatric patients aged 1 to 17 years to adults aged 18 to 44 years. The analysis used ICD-9 E-codes E885.0 to E885.4 using discharge data from the Nationwide Emergency Department Sample, Healthcare Cost and Utilization Project, Agency for Healthcare Research and Quality. Approximately 214 000 ED visits met study criteria. Skiing injuries had the highest percentage of hospitalizations (3.30% in pediatric patients and 6.65% in adults 18-44 years old). Skateboard and snowboard injuries were more likely to require hospitalization than roller skating injuries in pediatric patients (odds ratio = 2.42; 95% CI = 2.14-2.75 and odds ratio = 1.83; 95% CI =1.55-2.15, respectively). In contrast, skateboard and snowboard injuries were less severe than roller-skating injuries in adults. © The Author(s) 2015.

Radiometric and ultrasonic testing of vibrating roller compacting effects

International Nuclear Information System (INIS)

Prikryl, F.; Habarta, J.; Kovarikova, E.

1977-01-01

A hole was filled with two layers of concrete mixture. Each layer was compacted using a Dynapac CA 25 vibrating roller 10,000 kg in weight, operating with a frequency of 30 Hz. A concrete block thus produced had dimensions of 11.0x2.5 m and a height of 1.6 m. After the concrete block hardening (roughly 120 days) drill cores were bored and bulk density was determined using nondestructive methods. Bulk density determination of the concrete between the drill cores was conducted using a 137 Cs emitter of an activity of 89 GBq, a FHZ-88b Geiger-Mueller counter was used as the detector. The emitter and detector were placed to touch the bore wall and were lowered to different depths in 10 cm increments. 10 count rate values were measured in each depth. The measurement time was chosen such that the decay statistical error did not exceed 1;. Bulk density of the individual segments of the drill cores was determined using 60 Co of an activitBy of 55 Mq as the radiation source and a TESLA 20/100 GWl GM counter as the detector. The detector operating voltage was 1240 V. Ultrasonic measurements were conducted using the USME-5 instrument. The measured bulk density values show that the compacting of a concrete layer 80 cm in thickness using a vibrating roller is sufficiently efficient. Both nondestructive methods were well proven, the results show that bulk density values in different depths differ due to concrete moisture content. (J.P.)

Analysis of the assembling phase of lattice slabs

Directory of Open Access Journals (Sweden)

A. L. Sartorti

Full Text Available Lattice slabs are usual in Brazil. They are formed by precast joists with latticed bars on a base of concrete, and a cover of concrete placed at the jobsite. The assembly of the joists and the filling elements is simple and do not require manpower with great skill, presenting low cost-benefit ratio. However, it is precisely in assembling phase that arise questions related to the scaffold support distance. A mistake in the proper positioning can lead to two undesirable situations. In one of them, a small space between the support lines increases the cost of scaffold, and in other an excessive space can generate exaggerated displacements, and even the collapse of the slab in the stage of concreting. The objective of this work is to analyze the bearing capacity of lattice joists in assembling phase, looking for information that is useful in defining the scaffold support distance. Several joists were tested to define the failure modes and their load bearing capacities. The results allowed to determine equations for calculating the appropriate distance between the support lines of the joists.

Non-fuel bearing hardware melting technology

International Nuclear Information System (INIS)

Newman, D.F.

1993-01-01

Battelle has developed a portable hardware melter concept that would allow spent fuel rod consolidation operations at commercial nuclear power plants to provide significantly more storage space for other spent fuel assemblies in existing pool racks at lower cost. Using low pressure compaction, the non-fuel bearing hardware (NFBH) left over from the removal of spent fuel rods from the stainless steel end fittings and the Zircaloy guide tubes and grid spacers still occupies 1/3 to 2/5 of the volume of the consolidated fuel rod assemblies. Melting the non-fuel bearing hardware reduces its volume by a factor 4 from that achievable with low-pressure compaction. This paper describes: (1) the configuration and design features of Battelle's hardware melter system that permit its portability, (2) the system's throughput capacity, (3) the bases for capital and operating estimates, and (4) the status of NFBH melter demonstration to reduce technical risks for implementation of the concept. Since all NFBH handling and processing operations would be conducted at the reactor site, costs for shipping radioactive hardware to and from a stationary processing facility for volume reduction are avoided. Initial licensing, testing, and installation in the field would follow the successful pattern achieved with rod consolidation technology

Hot Ductility Behavior of an 8 Pct Cr Roller Steel

Science.gov (United States)

Wang, Zhenhua; Sun, Shuhua; Shi, Zhongping; Wang, Bo; Fu, Wantang

2015-04-01

The hot ductility of an 8 pct Cr roller steel was determined between 1173 K and 1473 K (900 °C and 1200 °C) at strain rates of 0.01 to 10 s-1 through tensile testing. The fracture morphology was observed using scanning electron microscopy, and the microstructure was examined through optical microscopy and transmission electron microscopy. The dependence of the hot ductility behavior on the deformation conditions, grain size, and precipitation was analyzed. The relationship between the reduction in area and the natural logarithm of the Zener-Hollomon parameter (ln Z) was found to be a second-order polynomial. When ln Z was greater than 40 s-1, the hot ductility was poor and fracture was mainly caused by incompatible deformation between the grains. When ln Z was between 32 and 40 s-1, the hot ductility was excellent and the main fracture mechanism was void linking. When ln Z was below 32 s-1, the hot ductility was poor and fracture was mainly caused by grain boundary sliding. A fine grain structure is beneficial for homogenous deformation and dynamic recrystallization, which induces better hot ductility. The effect of M7C3 carbide particles dispersed in the matrix on the hot ductility was small. The grain growth kinetics in the 8 pct Cr steel were obtained between 1373 K and 1473 K (1100 °C and 1200 °C). Finally, optimized preheating and forging procedures for 8 pct Cr steel rollers are provided.

Tribologic analysis and technical innovation for rotary molding press

International Nuclear Information System (INIS)

Luo Wei; Bai Yumeng; Dai Xingjian

2012-01-01

The rotary molding press R53C-Y is the key facility in the compression molding working procedure of the nu clear fuel pellets. Its main compression assembly called the upper compression roller frame has been worn seriously during the production. At first, the mechanical model of the upper compression roller assembly was established for analysis and calculation physical strength. Then the wear causations of the upper compression roller frame were analyzed, and the existent problems of central lubrication system were discussed. Finally, Oil-air central lubrication system was designed considering the characteristic of nuclear fuel pellets production. (authors)

Evaluation of effect of oil film of rotor bearing

Science.gov (United States)

Alekseeva, L. B.; Maksarov, V. V.

2018-03-01

The high-rpm rotors were subjected to the dynamic analysis. Oscillations of a rotor spinning in gapped bearings were considered. It was stated that the rotor necks motion pattern depends on a lot of factors: a ratio of static and dynamic loads on the bearing, radial clearance size, presence of oil film between a neck and a bearing, elastic and inertial properties of a mounting group. The most unfavourable mode where static and dynamic loads are equal was detected without taking into account the oil film impact. The impact of oil film on the bearing assembly dynamics is significant in high-rpm rotors. The presence of oil film can possibly cause rotor buckling failure and self-starting. Rotor motion stability in small was studied. Herewith, various schemes were considered. Expressions, determining the stability zones of a rigid rotor on the fixed support and the supports with elastic and inertial elements, were given.

Control rod upper pin and roller removal and replacement

International Nuclear Information System (INIS)

Giordano, B.

1995-01-01

There has been increasing utility interest in removing cobalt sources as a means to minimize dose rates and shipping costs associated with operations, maintenance, shipping and radioactive waste disposal. This activation product accounts for approximately 80% of the dose rates at a plant. Estimates suggest that older (original equipment) control rod blades (CRBs) using stellite rollers and Haynes Alloy 25 pins can contribute as much as 43% of the cobalt in the plant. Since CRBs are the most concentrated source of cobalt in the reactor vessel, pin and roller (P ampersand R) replacement will provide significant reductions in cobalt-60 levels. The reductions will be measurable within 2 years, and should plateau within 5 to 6 years. This paper described a new, simple, cost effective, field proven in-situ method to replace these high source term contributing components and return the CRB to the reactor core for continued service. The paper also briefly describes a methodology that has been developed to estimate the labor and material costs along with a man-rem dollar savings for removal of the upper P ampersand Rs from in-service CRBs purchased prior to 1982. This method permits comparison to the cost of early replacement of CRBs. The result of this study is an EXCEL spreadsheet cost/benefit analysis that can be made plant specific by incorporation of plant data. The Analysis shows that the removal of P ampersand Rs can be beneficial for a Co-60 contribution as low as 5-10%. Recent interest by non-utility radioactive material users in obtaining the removed P ampersand Rs may further increase the benefit and reduce the cost associated with in-situ removal

60NiTi Intermetallic Material Evaluation for Lightweight and Corrosion Resistant Spherical Sliding Bearings for Aerospace Applications, Report on NASA-Kamatics SAA3-1288

Science.gov (United States)

Dellacorte, Christopher; Jefferson, Michael

2015-01-01

Under NASA Space Act Agreement (SAA3-1288), NASA Glenn Research Center and the Kamatics subsidiary of the Kaman Corporation conducted the experimental evaluation of spherical sliding bearings made with 60NiTi inner races. The goal of the project was to assess the feasibility of manufacturing lightweight, corrosion resistant bearings utilizing 60NiTi for aerospace and industrial applications. NASA produced the bearings in collaboration with Abbott Ball Corporation and Kamatics fabricated bearing assemblies utilizing their standard reinforced polymer liner material. The assembled bearings were tested in oscillatory motion at a load of 4.54 kN (10,000 lb), according to the requirements of the plain bearing specification SAE AS81820. Several test bearings were exposed to hydraulic fluid or aircraft deicing fluid prior to and during testing. The results show that the 60NiTi bearings exhibit tribological performance comparable to conventional stainless steel (440C) bearings. Further, exposure of 60NiTi bearings to the contaminant fluids had no apparent performance effect. It is concluded that 60NiTi is a feasible bearing material for aerospace and industrial spherical bearing applications.

Modeling of contact theories for the manipulation of biological micro/nanoparticles in the form of circular crowned rollers based on the atomic force microscope

International Nuclear Information System (INIS)

Korayem, M. H.; Khaksar, H.; Taheri, M.

2013-01-01

This article has dealt with the development and modeling of various contact theories for biological nanoparticles shaped as cylinders and circular crowned rollers for application in the manipulation of different biological micro/nanoparticles based on Atomic Force Microscope. First, the effective contact forces were simulated, and their impact on contact mechanics simulation was investigated. In the next step, the Hertz contact model was simulated and compared for gold and DNA nanoparticles with the three types of spherical, cylindrical, and circular crowned roller type contact geometries. Then by reducing the length of the cylindrical section in the circular crowned roller geometry, the geometry of the body was made to approach that of a sphere, and the results were compared for DNA nanoparticles. To anticipatory validate the developed theories, the results of the cylindrical and the circular crowned roller contacts were compared with the results of the existing spherical contact simulations. Following the development of these contact models for the manipulation of various biological micro/nanoparticles, the cylindrical and the circular crowned roller type contact theories were modeled based on the theories of Lundberg, Dowson, Nikpur, Heoprich, and Hertz for the manipulation of biological micro/nanoparticles. Then, for a more accurate validation, the results obtained from the simulations were compared with those obtained by the finite element method and with the experimental results available in previous articles. The previous research works on the simulation of nanomanipulation have mainly investigated the contact theories used in the manipulation of spherical micro/nanoparticles. However since in real biomanipulation situations, biological micro/nanoparticles of more complex shapes need to be displaced in biological environments, this article therefore has modeled and compared, for the first time, different contact theories for use in the biomanipulation of

Acute, fatal Sarcocystis calchasi-associated hepatitis in Roller pigeons (Columbia livia f. dom.) at Philadelphia Zoo

Science.gov (United States)

Four Roller pigeons (Columba livia f. dom.) at the Philadelphia Zoo died suddenly. Necropsy examination revealed macroscopic hepatitis. Microscopically, the predominant lesions were in liver, characterized with necrosis and mixed cell inflammatory response. Sarcocystis calchasi-like schizonts and fr...

The effect of extrusion and drying on roller techniques concerning the rheological characteristics of rice-, corn-, sweet potato-, bean- and cassava root- and leaf- based composite flour

Directory of Open Access Journals (Sweden)

Johanna Aristizábal Galvis

2013-01-01

Full Text Available Promoting food security in Latin-America and the Caribbean is directly related to agricultural products. The region faces a food crisis which has reduced large population groups’ access to food. This work contributes to the study of obtaining precooked composite flour made from biofortified crops using protein, vitamin A and/or minerals. This study evaluated the effect of precooked flour’s composition and precooking on its solubility in water, water absorption capacity, consistency and viscosity; such flour was obtained by extrusion and drying on rollers. The composite flours were obtained from cassava roots, sweet potato tubers, corn, rice and bean grains and cassava leaves. Four composite flours were formulated taking four- to six-year-old children’s daily nutrient requirements (protein, iron, zinc and beta-carotenes as a basis. The extruder was operated at 90ºC, 300 rpm screw rotation speed, 17.64 g/min feed flow, with 30% moisture mixture. The dryer rollers were operated at 4 rpm roller rotation speed, 90ºC surface temperature and 1 mm separation between rollers. It was determined that flour dried on rollers led to more complete cooking and modified starch granule structure than precooking by extrusion, thereby producing flour having greater solubility in water, less water absorption, higher consistency and smaller viscosity, comparable to that of pattern flour.

Development of active magnetic bearings and ferrofluid seals toward oil free sodium pumps

International Nuclear Information System (INIS)

Sreedhar, B.K.; Kumar, R. Nirmal; Sharma, Prashant; Ruhela, Shivprakash; Philip, John; Sundarraj, S.I.; Chakraborty, N.; Mohana, M.; Sharma, Vijay; Padmakumar, G.; Nashine, B.K.; Rajan, K.K.

2013-01-01

Sodium centrifugal pumps employ conventional oil cooled bearings and mechanical seals to support the rotor assembly outside sodium and to seal the cover gas from the atmosphere. Although engineered safety features are incorporated in the design and detailed operational procedures formulated to ensure that no oil contamination of sodium can occur, there have been incidents of oil ingress into sodium. A design variant that eliminates the need for oil in top bearings and seals is therefore a promising option. This paper discusses the work in progress to develop a magnetic bearing and ferrofluid seal combination that can achieve this purpose

Molten core retention assembly

International Nuclear Information System (INIS)

Lampe, R.F.

1976-01-01

Molten fuel produced in a core overheating accident is caught by a molten core retention assembly consisting of a horizontal baffle plate having a plurality of openings therein, heat exchange tubes having flow holes near the top thereof mounted in the openings, and a cylindrical imperforate baffle attached to the plate and surrounding the tubes. The baffle assembly is supported from the core support plate of the reactor by a plurality of hanger rods which are welded to radial beams passing under the baffle plate and intermittently welded thereto. Preferably the upper end of the cylindrical baffle terminates in an outwardly facing lip to which are welded a plurality of bearings having slots therein adapted to accept the hanger rods

Tailoring luminescence color conversion via affinitive co-assembly of glutamates appended with pyrene and naphthalene dicarboximide units.

Science.gov (United States)

Xing, Pengyao; Zhao, Zhuo; Hao, Aiyou; Zhao, Yanli

2016-01-21

Structural matching of two organic building blocks bearing glutamate units and different luminophores assembled into unilamellar nanovesicles in aqueous media through a co-assembly process. Aggregation-induced energy transfer took place in the co-assembled system, leading to controllable generation of multiple luminescence colors including white light.

Nuclear reactor fuel assemblies and end fitting grid structures therefor

International Nuclear Information System (INIS)

Jabsen, F.S.

1978-01-01

An improved end fitting grid structure is described for nuclear fuel assemblies which overcomes the need for load-bearing control rod guide tubes and the expensive special fittings that these tubes required. (UK)

Mechanical seal assembly

Science.gov (United States)

Kotlyar, Oleg M.

2001-01-01

An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transferring it to the mechanical diode.

Mechanical Seal Assembly

Energy Technology Data Exchange (ETDEWEB)

Kotlyar, Oleg M.

1999-06-18

An improved mechanical seal assembly is provided for sealing rotating shafts with respect to their shaft housings, wherein the rotating shafts are subject to substantial axial vibrations. The mechanical seal assembly generally includes a rotating sealing ring fixed to the shaft, a non-rotating sealing ring adjacent to and in close contact with the rotating sealing ring for forming an annular seal about the shaft, and a mechanical diode element that applies a biasing force to the non-rotating sealing ring by means of hemispherical joint. The alignment of the mechanical diode with respect to the sealing rings is maintained by a series of linear bearings positioned axially along a desired length of the mechanical diode. Alternative embodiments include mechanical or hydraulic amplification components for amplifying axial displacement of the non-rotating sealing ring and transferring it to the mechanical diode.

Vorrichtung zum Aufnehmen und Abgeben von Stückgut an ein fahrerloses Transportfahrzeug

OpenAIRE

Schroer, W.

2008-01-01

The device (1) has comb-type bearing supporting bars (4) provided for passage of goods to be transported between rollers (9) of a running surface (2). An upper edge of the supporting bars is slightly higher than the running surface formed by the transport rollers. Stripping stoppers for the goods are provided in a driving direction behind the transport rollers. The supporting bars are designed in a raised or lowerable manner in a transport vehicle (3), where the supporting bars exhibit a fron...

Shock Hazard Prevention through Self-Healing Insulative Coating on SSA Metallic Bearings, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — The space suit assembly (SSA) contains metallic bearings at the wrist, neck, and waist, which are exposed to space environment, and pose a potential shock hazard....

The positioning of federate sports in Portugal: handball, basketball, roller hockey and volleyball

OpenAIRE

Gonçalves, Celina; Correia, Abel

2005-01-01

Sport is constituted by a multiplicity of activities with different purposes, concepts and cultural representations. Before the increase of supply, Sports Federations need to understand the practitioners in relation to the several possibilities of practice and to position their sports according to their competitors. In this context, the purpose of this study is the positioning of team federate sports (handball, basketball, roller hockey and volleyball). According to Lindon et al.,...

Probabilistic Analysis of Space Shuttle Body Flap Actuator Ball Bearings

Science.gov (United States)

Oswald, Fred B.; Jett, Timothy R.; Predmore, Roamer E.; Zaretsky, Erwin V.

2008-01-01

A probabilistic analysis, using the 2-parameter Weibull-Johnson method, was performed on experimental life test data from space shuttle actuator bearings. Experiments were performed on a test rig under simulated conditions to determine the life and failure mechanism of the grease lubricated bearings that support the input shaft of the space shuttle body flap actuators. The failure mechanism was wear that can cause loss of bearing preload. These tests established life and reliability data for both shuttle flight and ground operation. Test data were used to estimate the failure rate and reliability as a function of the number of shuttle missions flown. The Weibull analysis of the test data for the four actuators on one shuttle, each with a 2-bearing shaft assembly, established a reliability level of 96.9 percent for a life of 12 missions. A probabilistic system analysis for four shuttles, each of which has four actuators, predicts a single bearing failure in one actuator of one shuttle after 22 missions (a total of 88 missions for a 4-shuttle fleet). This prediction is comparable with actual shuttle flight history in which a single actuator bearing was found to have failed by wear at 20 missions.

The Selection of Materials for Roller Chains From The Perspective Of Manufacturing Process

Directory of Open Access Journals (Sweden)

Rahmat Saptono

2010-10-01

Full Text Available The selection of materials for an engineering component is not only requested by its design function and shape, but also the sequence through which it is manufactured. The manufacturing operation of roller chains involves drawing and trimming processes aimed at producing semi-finished chain drives component with a well-standardized dimension. In addition to final combination of properties required by design constraints, the ability of materials to be formed into a desired shape and geometry without failure is also critical. The objective of materials selection should therefore involve additional attributes that are not typically  accommodated by the standard procedure of materials selection. The present paper deals with the selection of materials for roller chains from the perspective of manufacturing process. Ears and un-uniform wall thickness have been identified as a key problem in the mass production of component. Provided all process parameters were established, the  anisotropy factor of materials is critical. Simulative test can be reasonably used to obtain material performance indices that can be added up to the standard procedure of material selection. Of three commercially available steel grades evaluated with regard to the criteria defined, one grade is more suitable for the present objective.

Development of ceramics for heavy-duty roller bearings in key sectors of future technologies. Ceramic bearings for turbomolecular pumps in semiconductor industry. Final report; Entwicklung von Hochleistungskeramiken fuer Keramikwaelzlager unter extremen Belastungen in Schluesselbereichen von Zukunftstechnologien. Keramikwaelzlager fuer Turbomolekularpumpen in der Halbleiterindustrie. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Stueber, H.G.; Adamietz, R.; Binninger, M. [and others

1999-09-01

The examined ceramic material shows high resistance against aggressive gases used in the semiconductor industry. In the test rigs for emergency bearings the full ceramic bearings without any lubricant didn't reach the requested life. Bearings with ZrO{sub 2}-rings reached higher life time compared to bearings with Si{sub 3}N{sub 4}-rings. The life of the emergency bearings increased when using C-ion implanted rings. By using this method the friction ratio decreased. In this case, bearings with ZrO{sub 2}-rings get nearly the life of the old standard hybrid emergency bearings. But they can't reach the life time of the latest state of development of hybrid bearings. A two row paired angular contact bearing seems to be a most promising modification. But this design shows problems while manufacturing. The so called pin-bush-bearing (a sliding friction bearing solution) shows good test results. It will be possible to optimise this bearing for different pumps. Tests with ceramic bearings in a conventional levitated pump were planned. It was not possible to start the tests because of the higher priority of the 'emergency bearing project'. (orig.) [German] Der untersuchte keramische Werkstoff weist eine hohe Bestaendigkeit gegenueber den in der Halbleiterindustrie verwendeten aggressiven Gasen auf. In den Fanglagerversuchen wurde deutlich, dass die untersuchten Vollkeramik-Waelzlager ohne Schmierstoff nicht die geforderten Standzeiten erreichen. Im Vergleich zwischen Si{sub 3}N{sub 4}-Ringen zur ZrO{sub 2}-Ringen lassen die Oxidringe eine hoehere Lebensdauer erwarten. Eine Verbesserung der Standzeiten konnte durch mit C-Ionen implantierten Ringe erzielt werden. Mit dieser Reibwertverbesserung konnten die Lager mit ZrO{sub 2}-Ringen zwar den alten Serienstandard mit Hybridlagern in etwa erreichen, andererseits sind zum jetzigen Serienstandard noch deutliche Unterschiede zu beobachten. Eine vielversprechende Modifikation des Lagers in Richtung eines

Fuel assemblies for nuclear reactors

International Nuclear Information System (INIS)

Jabsen, F.S.

1979-01-01

In a nuclear fuel assembly, hollow guide posts protrude into a fuel assembly and fitting grill from a biased spring pad with a plunger that moves with the spring pad plugging one end of each of the guide posts. A plate on the end fitting grill that has a hole for fluid discharge partially plugs the other end of the guide post. Pressurized water coolant that fills the guide post volume acts as a shock absorber and should the reactor core receive a major seismic or other shock, the fuel assembly is compelled to move towards a pad depending from a transversely disposed support grid. The pad bears against the spring pad and the plunger progressively blocks the orifices provided by slots in the guide posts thus gradually absorbing the applied shock. After the orifice has been completely blocked, controlled fluid discharge continues through a hole coil spring cooperating in the attenuation of the shock. (author)

Vibration measurements of the Daniel K. Inouye Solar Telescope mount, Coudé rotator, and enclosure assemblies

Science.gov (United States)

McBride, William R.; McBride, Daniel R.

2016-08-01

The Daniel K. Inouye Solar Telescope (DKIST) will be the largest solar telescope in the world, with a 4-meter off-axis primary mirror and 16 meter rotating Coudé laboratory within the telescope pier. The off-axis design requires a mount similar to an 8-meter on-axis telescope. Both the telescope mount and the Coudé laboratory utilize a roller bearing technology in place of the more commonly used hydrostatic bearings. The telescope enclosure utilizes a crawler mechanism for the altitude axis. As these mechanisms have not previously been used in a telescope, understanding the vibration characteristics and the potential impact on the telescope image is important. This paper presents the methodology used to perform jitter measurements of the enclosure and the mount bearings and servo system in a high-noise environment utilizing seismic accelerometers and high dynamic-range data acquisition equipment, along with digital signal processing (DSP) techniques. Data acquisition and signal processing were implemented in MATLAB. In the factory acceptance testing of the telescope mount, multiple accelerometers were strategically located to capture the six axes-of-motion of the primary and secondary mirror dummies. The optical sensitivity analysis was used to map these mirror mount displacements and rotations into units of image motion on the focal plane. Similarly, tests were done with the Coudé rotator, treating the entire rotating instrument lab as a rigid body. Testing was performed by recording accelerometer data while the telescope control system performed tracking operations typical of various observing scenarios. The analysis of the accelerometer data utilized noise-averaging fast Fourier transform (FFT) routines, spectrograms, and periodograms. To achieve adequate dynamic range at frequencies as low as 3Hz, the use of special filters and advanced windowing functions were necessary. Numerous identical automated tests were compared to identify and select the data sets

Dynamic behavior of air lubricated pivoted-pad journal-bearing, rotor system. 2: Pivot consideration and pad mass

Science.gov (United States)

Nemeth, Z. N.

1972-01-01

Rotor bearing dynamic tests were conducted with tilting-pad journal bearings having three different pad masses and two different pivot geometries. The rotor was vertically mounted and supported by two three-pad tilting-pad gas journal bearings and a simple externally pressurized thrust bearing. The bearing pads were 5.1 cm (2.02 in.) in diameter and 2.8 cm (1.5 in.) long. The length to diameter ratio was 0.75. One pad was mounted on a flexible diaphragm. The bearing supply pressure ranged from 0 to 690 kilonewtons per square meter (0 to 100 psig), and speeds ranged to 38,500 rpm. Heavy mass pad tilting-pad assemblies produced three rotor-bearing resonances above the first two rotor critical speeds. Lower supply pressure eliminated the resonances. The resonances were oriented primarily in the direction normal to the diaphragm.

Lab-scale roller table mill for investigating the grinding behaviour of coal

Energy Technology Data Exchange (ETDEWEB)

Werner, V.; Zelkowski, J.; Schoenert, K. [Inst. for Energy Process Engineering and Fuel Technology and Inst. of Mineral Processing, Univ. Clausthal, Clausthal-Zellerfeld (Germany)

1999-11-01

The test mill is equipped with one roller. The material bed can be discharged completely after overroling. Grinding force, torque and gap width are measured. Cycle tests with three coals have been performed for simulating a closed circuit process. The grinding behaviour is characterized by the following relations: compaction of the particle bed and specific power draft vs. specific grinding force, production of fine material (dust), circuit factor, specific surface of the dust and specific work-input of the grinding circuit vs. specific power draft. (orig.)

Marine aggregates and transparent exopolymeric particles (TEPs) as substrates for the stramenopilan fungi, the thraustochytrids: Roller table experimental approach.

Digital Repository Service at National Institute of Oceanography (India)

Damare, V.S.; Raghukumar, S.

In order to understand the kind of organic substrates utilized by thraustochytrids in the coastal water column, their growth in the presence of Transparent Exopolymeric Substances (TEPS) and aggregates generated in roller table experiments...

Post-cracking tensile behaviour of steel-fibre-reinforced roller-compacted-concrete for FE modelling and design purposes

International Nuclear Information System (INIS)

Jafarifar, N.; Pilakoutas, K.; Angelakopoulos, H.; Bennett, T.

2017-01-01

Fracture of steel-fibre-reinforced-concrete occurs mostly in the form of a smeared crack band undergoing progressive microcracking. For FE modelling and design purposes, this crack band could be characterised by a stress-strain (σ-ε) relationship. For industrially-produced steel fibres, existing methodologies such as RILEM TC 162-TDF (2003) propose empirical equations to predict a trilinear σ-ε relationship directly from bending test results. This paper evaluates the accuracy of these methodologies and their applicability for roller-compacted-concrete and concrete incorporating steel fibres recycled from post-consumer tyres. It is shown that the energy absorption capacity is generally overestimated by these methodologies, sometimes up to 60%, for both conventional and roller-compacted concrete. Tensile behaviour of fibre-reinforced-concrete is estimated in this paper by inverse analysis of bending test results, examining a variety of concrete mixes and steel fibres. A multilinear relationship is proposed which largely eliminates the overestimation problem and can lead to safer designs. [es

Automatic Identification of Subtechniques in Skating-Style Roller Skiing Using Inertial Sensors

Science.gov (United States)

Sakurai, Yoshihisa; Fujita, Zenya; Ishige, Yusuke

2016-01-01

This study aims to develop and validate an automated system for identifying skating-style cross-country subtechniques using inertial sensors. In the first experiment, the performance of a male cross-country skier was used to develop an automated identification system. In the second, eight male and seven female college cross-country skiers participated to validate the developed identification system. Each subject wore inertial sensors on both wrists and both roller skis, and a small video camera on a backpack. All subjects skied through a 3450 m roller ski course using a skating style at their maximum speed. The adopted subtechniques were identified by the automated method based on the data obtained from the sensors, as well as by visual observations from a video recording of the same ski run. The system correctly identified 6418 subtechniques from a total of 6768 cycles, which indicates an accuracy of 94.8%. The precisions of the automatic system for identifying the V1R, V1L, V2R, V2L, V2AR, and V2AL subtechniques were 87.6%, 87.0%, 97.5%, 97.8%, 92.1%, and 92.0%, respectively. Most incorrect identification cases occurred during a subtechnique identification that included a transition and turn event. Identification accuracy can be improved by separately identifying transition and turn events. This system could be used to evaluate each skier’s subtechniques in course conditions. PMID:27049388

Automatic Identification of Subtechniques in Skating-Style Roller Skiing Using Inertial Sensors

Directory of Open Access Journals (Sweden)

Yoshihisa Sakurai

2016-04-01

Full Text Available This study aims to develop and validate an automated system for identifying skating-style cross-country subtechniques using inertial sensors. In the first experiment, the performance of a male cross-country skier was used to develop an automated identification system. In the second, eight male and seven female college cross-country skiers participated to validate the developed identification system. Each subject wore inertial sensors on both wrists and both roller skis, and a small video camera on a backpack. All subjects skied through a 3450 m roller ski course using a skating style at their maximum speed. The adopted subtechniques were identified by the automated method based on the data obtained from the sensors, as well as by visual observations from a video recording of the same ski run. The system correctly identified 6418 subtechniques from a total of 6768 cycles, which indicates an accuracy of 94.8%. The precisions of the automatic system for identifying the V1R, V1L, V2R, V2L, V2AR, and V2AL subtechniques were 87.6%, 87.0%, 97.5%, 97.8%, 92.1%, and 92.0%, respectively. Most incorrect identification cases occurred during a subtechnique identification that included a transition and turn event. Identification accuracy can be improved by separately identifying transition and turn events. This system could be used to evaluate each skier’s subtechniques in course conditions.

THE RELATIONSHIP BETWEEN STIFFNESS LOSSES AND LOSSES IN BEARINGS OF ROPE BLOCKS

Directory of Open Access Journals (Sweden)

V. M. Bohomaz

2017-08-01

Full Text Available Purpose. To determine the efficiency of rope blocks, it is necessary to determine the stiffness coefficient of the ropes of blocks, taking into account the classification group of the mechanism and the wrapping angle of a block by a rope. At this one should use well-tested values of the efficiency coefficients of the rope blocks, taking into account the wrapping angle of a block by a rope and the analytically found friction coefficients of the rolling bearings given to the trunnion. Methodology. The work presents the analytical method of determining the coefficient of bearing resistance of the block when it is rotated by both the inner and outer cages, as well as the design scheme of the bearing of the block. Findings. The analysis of the lubrication method effect, the operating mode of the mechanism and the wrapping angle of a block by a rope on losses in bearings was carried out for rope blocks. The corresponding comparative tables of losses are given. Analysis of the obtained calculation results allows us to establish: 1 the main resistance affecting the cable blocks efficiency is the resistance in bearings; 2 the second largest component is the stiffness losses, depending on the operating mode, the wrapping angle of a block by a rope, the type of bearing lubrication; 3 the block efficiency when rotating the inner cage is higher than rotating the outer one by about 3% with thick lubrication and 1M mode; 4 in the sequential location of assemblies with a rolling bearing, it is necessary to strive for the design of the assembly in which the inner cage rotates; 5 with the number of blocks up to 5, one can use the recommended definitions of block bearings in the literature with an error in the efficiency value of up to 10%. Originality. The authors obtained values of resistances in the rolling bearings of the rope blocks and stiffness losses due to the girth of the block by the rope. In this case, dependences were used to determine the coefficient

MacDonald Dam reconstruction : using roller-compacted concrete

Energy Technology Data Exchange (ETDEWEB)

O' Neil, E. [AMEC Earth and Environmental Ltd., Sydney, NS (Canada)

2007-04-01

Located in Nova Scotia, the MacDonald Dam was commissioned in 1928. The dam consists of a 122 metre-long, 16 metre-high concrete structure comprised of an intake structure, stoplog openings, and a 34 metre-long free-overflow spillway. A 488 metre-long power canal was added as an upgrade in the 1950s. This paper provided details of the roller-compact concrete (RCC) used in the dam's recent rehabilitation following a dam failure analysis in 2003 by Nova Scotia Power Inc. RCC was chosen to help keep the dam's construction project on schedule. The layout and cross-section of the spillway was selected with consideration given to the RCC placing operation. A lift thickness of 0.20 m was selected. A formed ogee crest consisting of conventional reinforced concrete was constructed on top of the RCC. The downstream steps of the spillway were also covered with cast-in-place concrete. A low level sluice was designed to resist the weight of the wet RCC. The design compressive strength of the RCC was 20 MPa. The forms used to support the cast-in-place facing concrete on the upstream face of the dam were constructed full height and were braced back to the downstream face of the existing concrete structure prior to the start of RCC placement. Formwork inserts were placed in the facing concrete as construction progressed. Crack inducers were pre-placed on the forms. Aggregates from a local source were transported to a pug mill as the RCC construction progressed. The RCC was spread into 0.20 m lifts using a small bull-dozer, and the facing concrete was vibrated into the lift below. RCC lifts were compacted using a 9 tonne vibratory drum roller. The RCC placing operation was completed over a period of 10 days. Following the completion of the RCC portion of the dam, the remainder of the cast-in-place concrete was completed. It was concluded that the RCC provided a durable, low-maintenance structure that was completed at a lower price and in a shorter time-frame than

Influence of bearing pre-load coefficient on shaft vibration and pad temperature in a hydroturbine generator unit. A case study

Energy Technology Data Exchange (ETDEWEB)

Feng Fuzhou; Chu Fulei; Guo Dan; Lu Wenxiu [Tsinghua Univ., Beijing, BJ (China). Dept. of Precision Instruments

2001-07-01

From data collected by an online condition monitoring and fault diagnosis system, a higher pad temperature at the upper guide bearing in a pumped storage power generator unit installed in Guangdong province(GPSPS), China, was found. And also a relatively intensive shaft vibration occurred at the lower guide bearing. By calculating the Reynolds equation and viscosity-temperature equation of the lubricant, a curve between the pre-load coefficient and the increment of pad temperature is obtained, which shows that the larger, the pre-load coefficient, the bigger, the increment of pad temperature. For a practical unit in GPSPS, by employing Transfer matrix method and Wilson-{theta} method to analyze shaft vibration at different pre-load coefficients of the whole bearing or ''pad pair'' bearings, the results show that the larger the pre-load coefficient is, the smaller the vibration amplitude is, the shorter the time for vibration to become steady is. And an uneven pre-load coefficient of the ''pad pair'' bearings will cause shaft orbit from a circle to an ellipse whose long axes is at the direction of the ''pad pair'' with the lowest pre-load coefficient. Finally, reasons of higher pad temperature of the upper guide bearing and larger shaft vibration at the lower guide bearing are due to the inconsistent relation of bearing assembling clearance or pre-load coefficient of the upper and lower guide bearing, and also due to the too small, uneven pre-load coefficient of ''pad pair'' bearings. After a scheme for adjusting the bearing clearance is given, data measured show that the analysis and simulation methods are correct and the adjustment scheme to the assembling clearance of the upper and lower guide bearings is feasible and can be used to guide the field maintenance conveniently. (orig.)

Microstructure and soft magnetic properties of Finemet-type ribbons obtained by twin-roller melt-spinning

International Nuclear Information System (INIS)

Pozo Lopez, G.; Fabietti, L.M.; Condo, A.M.; Urreta, S.E.

2010-01-01

Soft magnetic ribbons of Finemet-type (Fe 73.5 Cu 1 Nb 3 Si 13.5 B 9 ) alloys are synthesized by the twin-roller melt-spinning technique directly from the melt, at tangential wheel speeds of 15, 18, 19 and 20 m/s. The microstructure and the magnetic properties are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), differential thermal analysis (DTA), thermo-gravimetric analysis (TGA) and hysteresis loops measurements. Samples cooled at 20 m/s are amorphous, while those quenched at lower wheel speeds are partially crystalline. All samples studied present saturation magnetization values (150-160 A m 2 /kg) higher than the commercial Finemet alloys (∼135 A m 2 /kg), obtained by controlled crystallization of amorphous single-roller melt-spun alloys. Optimal soft magnetic properties - σ S =(154±8) A m 2 /kg and H C =(6.9±0.9) A/m - are found in samples quenched at 19 m/s, consisting of size-distributed bcc Fe-Si nanograins (∼18 nm in average) embedded in an amorphous residual matrix. A minority nanocrystalline magnetic phase (≤10 nm) is also detected.

Performance of integrated systems of automated roller shade systems and daylight responsive dimming systems

Energy Technology Data Exchange (ETDEWEB)

Park, Byoung-Chul; Choi, An-Seop; Jeong, Jae-Weon [Department of Architectural Engineering, Sejong University, Kunja-Dong, Kwangjin-Gu, Seoul (Korea, Republic of); Lee, Eleanor S. [Building Technologies Department, Lawrence Berkeley National Laboratory, Berkeley, CA (United States)

2011-03-15

Daylight responsive dimming systems have been used in few buildings to date because they require improvements to improve reliability. The key underlying factor contributing to poor performance is the variability of the ratio of the photosensor signal to daylight workplane illuminance in accordance with sun position, sky condition, and fenestration condition. Therefore, this paper describes the integrated systems between automated roller shade systems and daylight responsive dimming systems with an improved closed-loop proportional control algorithm, and the relative performance of the integrated systems and single systems. The concept of the improved closed-loop proportional control algorithm for the integrated systems is to predict the varying correlation of photosensor signal to daylight workplane illuminance according to roller shade height and sky conditions for improvement of the system accuracy. In this study, the performance of the integrated systems with two improved closed-loop proportional control algorithms was compared with that of the current (modified) closed-loop proportional control algorithm. In the results, the average maintenance percentage and the average discrepancies of the target illuminance, as well as the average time under 90% of target illuminance for the integrated systems significantly improved in comparison with the current closed-loop proportional control algorithm for daylight responsive dimming systems as a single system. (author)

Summary of SEMO experience with PWR's cores containing Gadolinia bearing fuel in Tihange 1 nuclear power station

International Nuclear Information System (INIS)

Melice, M.; Jadot, J.J.; Duflou, P.; Wergifosse, C. de

1984-01-01

Future operating plans for Tihange unit 1 are based on cycle lengths approaching 18 months (from cycle 12). Since cycle 7, Gadolinia bearing assemblies were included in the reload batches in order to evaluate neutronic design methods employed. This Gadolinia program is briefly set out. Comparisons of measured to calculated data following the performance of the Gadolinia assemblies through cycles 7 and 8 are discussed. Loading pattern of cycle 9 including 4 Gadolinia high concentration assemblies and special features of cycle 10 are presented. An original device for ''in situ'' Gadolinia rod insertion into fresh assemblies is shortly described. (author)

Purex canyon exhaust fan bearing temperature monitoring system doric 245 datalogger programming

International Nuclear Information System (INIS)

Blackaby, W.B.

1994-01-01

A micro-processor based datalogger is used to monitor, display, and log seventeen RTD temperature channels. Five bearings are monitored for each of the three electric motor-fan assemblies and two bearings are monitored on the steam turbine unit. Several alarms per data channel (a High alarm at 236 degrees and a High High alarm at 246 degrees F) will alert the operation's staff to increasing abnormal bearing temperatures. This procedure is cross-referenced to the manufacturers manual. All programming steps will have the following footnote: Mpg x-xx. The Mpg refers to the Manual page, with x as the section number and xx as the page number in that section. When more information is needed, such as pictures or details, then the manual section and page number is provided

Bearing system

Science.gov (United States)

Kapich, Davorin D.

1987-01-01

A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

Occupational exposure to unburnt tobacco and potential risk of toxic optic neuropathy: A cross-sectional study among beedi rollers in selected rural areas of coastal Karnataka, India.

Directory of Open Access Journals (Sweden)

Soujanya Kaup

Full Text Available Beedi also known as poor man's cigarette is manufactured in almost all major states of India. Beedi workers are exposed to various health risks. There is an increased risk of systemic absorption of tobacco through skin and mucous membrane. The optic nerve is susceptible to damage from several toxic substances including tobacco. This group of disorders is known as toxic optic neuropathy (TON. The association of TON with occupational exposure to unburnt tobacco in beedi rollers has not been explored.Among the beedi rollers in Mangaluru and Bantwal talukas of Dakshina Kannada District, Karnataka, India: to assess the magnitude of potential TON utilizing colour vision and contrast sensitivity as screening tools and to identify the demographic, biological and occupational factors associated with potential TON.A community-based cross-sectional study was conducted from April-Sept 2016 in Mangaluru and Bantwal talukas, of Dakshina Kannada district, Karnataka. Beedi rollers from twelve villages (six from each taluka were included. In each of the selected villages, the investigators identified beedi collection centres and all the eligible beedi rollers were included in the study till the required number of beedi rollers for that village was achieved. Participants were screened at the study site for visual acuity, colour vision and contrast sensitivity and those with abnormal colour and contrast sensitivity in the presence of good visual acuity were considered to have potential TON.A total of 377 beedi rollers were approached; of which 365 consented to take part in the study (response rate: 96.81%. Women constituted the majority of the participants (n = 338, 92.6%. Based on the screening criteria, the prevalence of potential TON was 17.5% (n = 64, 95% CI: 13.5-21.9. On multiple logistic regression analysis, duration of beedi rolling (Adj OR: 1.061; 95% CI 1.015-1.109, p = 0.009, advancing age (Adj OR: 1.096; 95% CI 1.058-1.136, p<0.001 and presence of

Alred Roller – An Innovator and a Traditionalist

Directory of Open Access Journals (Sweden)

Zavarský Ján

2017-12-01

Full Text Available This study focuses on the scenographer Alfred Roller (1864–1935 and his productions of Wagner’s musical dramas, with emphasis on Tristan and Isolde and Parsifal. It places Roller’s aesthetics in a historical, aesthetic, and artistic context, points to his inspiration by the Swiss scenography reformer Adolphe Appia, and cooperation with the music composer and conductor Gustav Mahler in the Vienna Court Opera. The text analyses the specifics of Roller’s scenography, which diverged from illusive stage and used light work as an important production principle. It concludes with a summary of the effect of Roller’s aesthetics on Ľudovít Hradský, the first leader of the production team at the Slovak National Theatre (1923–1928. The visual aspects of the Slovak National Theatre’s productions in that period were strongly inspired by expressionism and Art Nouveau, which were typical of German theatre at that time.

Abrasion Resistance and Mechanical Properties of Waste-Glass-Fiber-Reinforced Roller-compacted Concrete

Science.gov (United States)

Yildizel, S. A.; Timur, O.; Ozturk, A. U.

2018-05-01

The potential use of waste glass fibers in roller-compacted concrete (RCC) was investigated with the aim to improve its performance and reduce environmental effects. The research was focused on the abrasion resistance and compressive and flexural strengths of the reinforced concrete relative to those of reference mixes without fibers. The freeze-thaw resistance of RCC mixes was also examined. It was found that the use of waste glass fibers at a rate of 2 % increased the abrasion resistance of the RCC mixes considerably.

High-throughput creation of micropatterned PDMS surfaces using microscale dual roller casting

International Nuclear Information System (INIS)

DiBartolomeo, Franklin J; Ge, Ning; Trinkle, Christine A

2012-01-01

This work introduces microscale dual roller casting (MDRC), a novel high-throughput fabrication method for creating continuous micropatterned surfaces using thermosetting polymers. MDRC utilizes a pair of rotating, heated cylindrical molds with microscale surface patterns to cure a continuous microstructured film. Using unmodified polydimethylsiloxane as the thermosetting polymer, we were able to create optically transparent, biocompatible surfaces with submicron patterning fidelity. Compared to other roll-to-roll fabrication processes, this method offers increased flexibility in the types of materials and topography that can be generated, including dual-sided patterning, embedded materials and tunable film thickness. (paper)

Influence of ambient moisture on the compaction behavior of microcrystalline cellulose powder undergoing uni-axial compression and roller-compaction: a comparative study using near-infrared spectroscopy.

Science.gov (United States)

Gupta, Abhay; Peck, Garnet E; Miller, Ronald W; Morris, Kenneth R

2005-10-01

This study evaluates the effect of variation in the ambient moisture on the compaction behavior of microcrystalline cellulose (MCC) powder. The study was conducted by comparing the physico-mechanical properties of, and the near infrared (NIR) spectra collected on, compacts prepared by roller compaction with those collected on simulated ribbons, that is, compacts prepared under uni-axial compression. Relative density, moisture content, tensile strength (TS), and Young modulus were used as key sample attributes for comparison. Samples prepared at constant roller compactor settings and feed mass showed constant density and a decrease in TS with increasing moisture content. Compacts prepared under uni-axial compression at constant pressure and compact mass showed the opposite effect, that is, density increased while TS remained almost constant with increasing moisture content. This suggests difference in the influence of moisture on the material under roller compaction, in which the roll gap (i.e., thickness and therefore density) remains almost constant, vs. under uni-axial compression, in which the thickness is free to change in response to the applied pressure. Key sample attributes were also related to the NIR spectra using multivariate data analysis by the partial least squares projection to latent structures (PLS). Good agreement was observed between the measured and the NIR-PLS predicted values for all key attributes for both, the roller compacted samples as well as the simulated ribbons. Copyright (c) 2005 Wiley-Liss, Inc. and the American Pharmacists Association

Stress analysis of jacks, frame and bearing connections, and drill rod for core sampler truck No. 2

International Nuclear Information System (INIS)

Ziada, H.H.

1995-01-01

This analysis evaluates the structural design adequacy of several components and connections for the rotary mode core sampler truck (RMCST) No. 2. This analysis was requested by the Characterization Equipment Group (WHC 1994a). The components addressed in this report are listed below: front jack assembly and connection to the truck chassis; rear jack assembly and connection to the truck chassis; center outrigger jacks and connection to the truck chassis; lower frame assembly and connection to the truck chassis; bolt connections for bearing plate assembly (for path of maximum load); traverse slide brackets and mounting of the traverse jack cylinders; and drill rod (failure loads)

Journal bearing

Science.gov (United States)

Menke, John R.; Boeker, Gilbert F.

1976-05-11

1. An improved journal bearing comprising in combination a non-rotatable cylindrical bearing member having a first bearing surface, a rotatable cylindrical bearing member having a confronting second bearing surface having a plurality of bearing elements, a source of lubricant adjacent said bearing elements for supplying lubricant thereto, each bearing element consisting of a pair of elongated relatively shallowly depressed surfaces lying in a cylindrical surface co-axial with the non-depressed surface and diverging from one another in the direction of rotation and obliquely arranged with respect to the axis of rotation of said rotatable member to cause a flow of lubricant longitudinally along said depressed surfaces from their distal ends toward their proximal ends as said bearing members are rotated relative to one another, each depressed surface subtending a radial angle of less than 360.degree., and means for rotating said rotatable bearing member to cause the lubricant to flow across and along said depressed surfaces, the flow of lubricant being impeded by the non-depressed portions of said second bearing surface to cause an increase in the lubricant pressure.

Bearing defect signature analysis using advanced nonlinear signal analysis in a controlled environment

Science.gov (United States)

Zoladz, T.; Earhart, E.; Fiorucci, T.

1995-01-01

Utilizing high-frequency data from a highly instrumented rotor assembly, seeded bearing defect signatures are characterized using both conventional linear approaches, such as power spectral density analysis, and recently developed nonlinear techniques such as bicoherence analysis. Traditional low-frequency (less than 20 kHz) analysis and high-frequency envelope analysis of both accelerometer and acoustic emission data are used to recover characteristic bearing distress information buried deeply in acquired data. The successful coupling of newly developed nonlinear signal analysis with recovered wideband envelope data from accelerometers and acoustic emission sensors is the innovative focus of this research.

Camshaft bearing arrangement

Energy Technology Data Exchange (ETDEWEB)

Aoi, K.; Ozawa, T.

1986-06-10

A bearing arrangement is described for the camshaft of an internal combustion engine or the like which camshaft is formed along its length in axial order with a first bearing surface, a first cam lobe, a second bearing surface, a second cam lobe, a third bearing surface, a third cam lobe and a fourth bearing surface, the improvement comprising first bearing means extending around substantially the full circumference of the first bearing surface and journaling the first bearing surface, second bearing means extending around substantially less than the circumference of the second bearing surface and journaling the second bearing surface, third bearing means extending around substantially less than the circumference of the third bearing surface and journaling the third bearing surface, and fourth bearing means extending around substantially the full circumference of the fourth bearing surface and journaling the first bearing surface.

Justification of the Shape of a Non-Circular Cross-Section for Drilling With a Roller Cutter

Science.gov (United States)

Buyalich, Gennady; Husnutdinov, Mikhail

2017-11-01

The parameters of the shape of non-circular cross-section affect not only the process of blasting, but also the design of the tool and the process of drilling as well. In the conditions of open-pit mining, it is reasonable to use a roller cutter to produce a non-circular cross-section of blasting holes. With regard to the roller cutter, the impact of the cross-section shape on the oscillations of the axial force arising upon its rotation is determined. It is determined that a polygonal shape with rounded comers of the borehole walls connections and their convex shape, which ensures a smaller range of the total axial force and the torque deflecting the bit from the axis of its rotation is the rational form of the non-circular cross-section of the borehole in terms of bit design. It has been shown that the ratio of the number of cutters to the number of borehole corners must be taken into account when justifying the shape of the cross-section, both from the point of view of the effectiveness of the explosion action and from the point of view of the rational design of the bit.

A review of raw wool carbonising

CSIR Research Space (South Africa)

Mozes, TE

1986-04-01

Full Text Available by means of a series of heavy crush rollers, mounted on roller bearings. The dust resulting from the crushing is removed in a deduster or &eying machine, which has an adjustable speed to cater for different types of wool and incorporates specially... , INTRODUCTION I 2. CONVENTIONALCARBONISING O F WOOL .................................. 1 2.1 Scouring 2 . . . 2.2 Actdmng ....................................................................................... 2 2.2.1 AcidisinaConditions and their Effect...

Use of flyash in roller compacted concrete for Ghatghar pumped storage scheme in Maharashtra

Energy Technology Data Exchange (ETDEWEB)

Damani, R.L.; Kshirsagar, S.L.; Narkhede, C.L. [MERI, Nashik (India)

2003-07-01

The paper described the use of 'Roller Compacted Concrete' (RCE) in which about 60% of the cement will be replaced by fly ash for construction of two storage dams - Upper dam and Lower dam in the Thane district of India. These are part of the Ghatghar Pumped Storage Scheme to generate hydropower. Fly ash from Eklahare and Dahav thermal power plant and processed fly ash, Pozzocrete 63 and 83b grade, all proved suitable for the RCC mix. 1 tab.

A FIB/TEM study of butterfly crack formation and white etching area (WEA) microstructural changes under rolling contact fatigue in 100Cr6 bearing steel

International Nuclear Information System (INIS)

Evans, M.-H.; Walker, J.C.; Ma, C.; Wang, L.; Wood, R.J.K.

2013-01-01

Butterflies are microscopic damage features forming at subsurface material imperfections induced during rolling contact fatigue (RCF) in rolling element bearings. Butterflies can lead to degradation of the load bearing capacity of the material by their associated cracks causing premature spalling failures. Recently, butterfly formation has been cited to be related to a premature failure mode in wind turbine gearbox bearings; white structure flaking (WSF). Butterflies consist of cracks with surrounding microstructural change called ‘white etching area’ (WEA) forming wings that revolve around their initiators. The formation mechanisms of butterflies in bearing steels have been studied over the last 50 years, but are still not fully understood. This paper presents a detailed microstructural analysis of a butterfly that has initiated from a void in standard 100Cr6 bearing steel under rolling contact fatigue on a laboratory two-roller test rig under transient operating conditions. Analysis was conducted using focused ion beam (FIB) tomography, 3D reconstruction and transmission electron microscopy (STEM/TEM) methods. FIB tomography revealed an extensive presence of voids/cavities immediately adjacent to the main crack on the non-WEA side and at the crack tip. This provides evidence for a void/cavity coalescence mechanism for the butterfly cracks formation. Spherical M 3 C carbide deformation and dissolution as part of the microstructural change in WEA were observed in both FIB and STEM/TEM analyses, where TEM analyses also revealed the formation of superfine nano-grains (3–15 nm diameter) intersecting a dissolving spherical M 3 C carbide. This is evidence of the early formation of nano-grains associated with the WEA formation mechanism

A FIB/TEM study of butterfly crack formation and white etching area (WEA) microstructural changes under rolling contact fatigue in 100Cr6 bearing steel

Energy Technology Data Exchange (ETDEWEB)

Evans, M.-H., E-mail: martin.evans@soton.ac.uk [National Centre for Advanced Tribology at Southampton (nCATS), University of Southampton, SO17 1BJ (United Kingdom); Walker, J.C.; Ma, C.; Wang, L.; Wood, R.J.K. [National Centre for Advanced Tribology at Southampton (nCATS), University of Southampton, SO17 1BJ (United Kingdom)

2013-05-15

Butterflies are microscopic damage features forming at subsurface material imperfections induced during rolling contact fatigue (RCF) in rolling element bearings. Butterflies can lead to degradation of the load bearing capacity of the material by their associated cracks causing premature spalling failures. Recently, butterfly formation has been cited to be related to a premature failure mode in wind turbine gearbox bearings; white structure flaking (WSF). Butterflies consist of cracks with surrounding microstructural change called ‘white etching area’ (WEA) forming wings that revolve around their initiators. The formation mechanisms of butterflies in bearing steels have been studied over the last 50 years, but are still not fully understood. This paper presents a detailed microstructural analysis of a butterfly that has initiated from a void in standard 100Cr6 bearing steel under rolling contact fatigue on a laboratory two-roller test rig under transient operating conditions. Analysis was conducted using focused ion beam (FIB) tomography, 3D reconstruction and transmission electron microscopy (STEM/TEM) methods. FIB tomography revealed an extensive presence of voids/cavities immediately adjacent to the main crack on the non-WEA side and at the crack tip. This provides evidence for a void/cavity coalescence mechanism for the butterfly cracks formation. Spherical M{sub 3}C carbide deformation and dissolution as part of the microstructural change in WEA were observed in both FIB and STEM/TEM analyses, where TEM analyses also revealed the formation of superfine nano-grains (3–15 nm diameter) intersecting a dissolving spherical M{sub 3}C carbide. This is evidence of the early formation of nano-grains associated with the WEA formation mechanism.

Use of the thin layer activation technique to measure on-line aeronautical components wear

International Nuclear Information System (INIS)

Chevalier, A.; Dubois, G.; Escuriol, M.; Monnot, R.; Pommier, S.; Fehsenfeld, P.; Kleinrahm, A.; Delvigne, T.; Le Menestrel, M.

1992-01-01

The superficial activation technique was applied in order to study the phenomena odscaling at the level of a reactor bearing. The exterior path of the bearing roller was activated on its whole contact surface and to a depth of 80 μm, according to the reaction 56 Fe(p, n) 56 Co. In spite of a very low rate of activation of 0.5 MBq, the first signs of scaling were detected 30 min before a notable rise in the vibratory level could be recorded. Then, the amount of scaled matter escaping from the outer ring of the roller could be followed continuously, with a precision of 0.2 mg. 5 refs., 7 figs

Failure Analysis and Recovery of a 50 MM Highly Elastic Intermetallic NiTi Ball Bearing for an ISS Application

Science.gov (United States)

DellaCorte, Christopher; Howard, S. Adam; Moore, Lewis E., III

2016-01-01

The ISS Distillation Assembly centrifuge is the pathfinder application for 50mm bore, deep-groove ball bearings made from the highly elastic intermetallic material 60NiTi. Superior corrosion and shock resistance are required to withstand the acidic wastewater exposure and heavy spacecraft launch related loads that challenge conventional steel bearings. During early ground testing one bearing unexpectedly and catastrophically failed after operating for only 200 hours of run time. A second bearing running on the same shaft was completely unaffected. A thorough investigation into the root cause of the failure determined that an excessively tight press-fit of the bearing outer race coupled with NiTis relatively low elastic modulus were key contributing factors. The proposed failure mode was successfully duplicated by experiment. To further corroborate the root cause theory, a successful bearing life test using improved installation practices (selective fitting) was conducted. The results show that NiTi bearings are suitable for space applications provided that care is taken to accommodate their unique material characteristics.

Evolutionary history of enigmatic bears in the Tibetan Plateau-Himalaya region and the identity of the yeti.

Science.gov (United States)

Lan, Tianying; Gill, Stephanie; Bellemain, Eva; Bischof, Richard; Nawaz, Muhammad Ali; Lindqvist, Charlotte

2017-12-13

Although anecdotally associated with local bears ( Ursus arctos and U. thibetanus ), the exact identity of 'hominid'-like creatures important to folklore and mythology in the Tibetan Plateau-Himalaya region is still surrounded by mystery. Recently, two purported yeti samples from the Himalayas showed genetic affinity with an ancient polar bear, suggesting they may be from previously unrecognized, possibly hybrid, bear species, but this preliminary finding has been under question. We conducted a comprehensive genetic survey of field-collected and museum specimens to explore their identity and ultimately infer the evolutionary history of bears in the region. Phylogenetic analyses of mitochondrial DNA sequences determined clade affinities of the purported yeti samples in this study, strongly supporting the biological basis of the yeti legend to be local, extant bears. Complete mitochondrial genomes were assembled for Himalayan brown bear ( U. a. isabellinus ) and black bear ( U. t. laniger ) for the first time. Our results demonstrate that the Himalayan brown bear is one of the first-branching clades within the brown bear lineage, while Tibetan brown bears diverged much later. The estimated times of divergence of the Tibetan Plateau and Himalayan bear lineages overlap with Middle to Late Pleistocene glaciation events, suggesting that extant bears in the region are likely descendants of populations that survived in local refugia during the Pleistocene glaciations. © 2017 The Authors.

Evolutionary history of enigmatic bears in the Tibetan Plateau–Himalaya region and the identity of the yeti

Science.gov (United States)

Lan, Tianying; Gill, Stephanie; Bellemain, Eva; Bischof, Richard; Nawaz, Muhammad Ali

2017-01-01

Although anecdotally associated with local bears (Ursus arctos and U. thibetanus), the exact identity of ‘hominid’-like creatures important to folklore and mythology in the Tibetan Plateau–Himalaya region is still surrounded by mystery. Recently, two purported yeti samples from the Himalayas showed genetic affinity with an ancient polar bear, suggesting they may be from previously unrecognized, possibly hybrid, bear species, but this preliminary finding has been under question. We conducted a comprehensive genetic survey of field-collected and museum specimens to explore their identity and ultimately infer the evolutionary history of bears in the region. Phylogenetic analyses of mitochondrial DNA sequences determined clade affinities of the purported yeti samples in this study, strongly supporting the biological basis of the yeti legend to be local, extant bears. Complete mitochondrial genomes were assembled for Himalayan brown bear (U. a. isabellinus) and black bear (U. t. laniger) for the first time. Our results demonstrate that the Himalayan brown bear is one of the first-branching clades within the brown bear lineage, while Tibetan brown bears diverged much later. The estimated times of divergence of the Tibetan Plateau and Himalayan bear lineages overlap with Middle to Late Pleistocene glaciation events, suggesting that extant bears in the region are likely descendants of populations that survived in local refugia during the Pleistocene glaciations. PMID:29187630

MONITORING DIAGNOSTIC INDICATORS DURING OPERATION OF A PRINT MACHIN

Directory of Open Access Journals (Sweden)

Jozef Dobránsky

2015-11-01

Full Text Available This article deals with monitoring diagnostic indicators during the operation of a machine used for production of packing materials with a print. It analyses low-frequency vibrations measured in individual spherical roller bearings in eight print positions. The rollers in these positions have a different pressure based on positioning these rollers in relation to the central roller. As a result, the article also deals with a correlation of pressure and level of measured low-frequency vibrations. The speed of the print machine (the speed of a line in meters per minute is a very important variable during its operation, this is why it is important to verify the values of vibrations in various speeds of the line, what can lead to revelation of one or more resonance areas. Moreover, it examines vibrations of the central roller drive and measurement of backlash of transmission cogs of this drive. Based on performed analyses recommendations for an operator of the machine have been conceived.

Multicriteria Analysis of Assembling Buildings from Steel Frame Structures

Science.gov (United States)

Miniotaite, Ruta

2017-10-01

Steel frame structures are often used in the construction of public and industrial buildings. They are used for: all types of slope roofs; walls of newly-built public and industrial buildings; load bearing structures; roofs of renovated buildings. The process of assembling buildings from steel frame structures should be analysed as an integrated process influenced by such factors as construction materials and machinery used, the qualification level of construction workers, complexity of work, available finance. It is necessary to find a rational technological design solution for assembling buildings from steel frame structures by conducting a multiple criteria analysis. The analysis provides a possibility to evaluate the engineering considerations and find unequivocal solutions. The rational alternative of a complex process of assembling buildings from steel frame structures was found through multiple criteria analysis and multiple criteria evaluation. In multiple criteria evaluation of technological solutions for assembling buildings from steel frame structures by pairwise comparison method the criteria by significance are distributed as follows: durability is the most important criterion in the evaluation of alternatives; the price (EUR/unit of measurement) of a part of assembly process; construction workers’ qualification level (category); mechanization level of a part of assembling process (%), and complexity of assembling work (in points) are less important criteria.

Effects of Cardinal Direction on Distribution and Populational Dynamism of Oak Leaf Roller (Tortrix viridana L. on Quercus infectoria Oliv. and Q. libani Lindl.

Directory of Open Access Journals (Sweden)

mohammadreza zargaran

2018-01-01

Full Text Available Introduction Various pests attack oak trees and in most cases heavily damage them. The European oak leaf roller is one of the important oak pests in some provinces of the Zagros, and it is an important pest of oak forests in some European and North African countries, as well as in Iraq and other regions of Iran. In Iran, it is scattered in the Zagros oak forests, especially in Kohkiluyeh and Boyer Ahmad, Lorestan, Chahar Mahal and Bakhtiari, Fars, and West Azarbaijan Provinces. Repeated removal of oak leaves, particularly by herbivores such as T. viridana in spring, reduces stored photosynthates in trees leading to their decreased diametrical growth. Materials and Methods The Ghabre-Hossein region (Piranshahr was selected as the field operations region because it is one of the most important infestation centers of the European oak leaf roller in the oak forests of West-Azerbaijan. The research was carried out in two consecutive years. Samples of larval instars were taken in early May. Since the sample plot in sampling methods can be points or lines (transects, the four cardinal directions were selected in this study and transects at 100 m intervals were located in each direction.To reduce sampling error, Aleppo (Quercus infectoria and Lebanon (Q. libani oak trees were selected for measurements that were similar in appearance and almost uniform with crowns or trunks aligned along the transects. In each studied tree, four suitable branches were selected (one in each cardinal direction, and the number of larvae from the tip of each branch to a length of 50 cm inwards was counted and recorded in forms prepared beforehand. Considering studies that were carried out regarding the biology of the pest, the larvae were counted in mid-May when all larvae were in their last (fifth instar. In all, 30 Aleppo and 30 Lebanon oak trees were selected in each cardinal direction, and four branches in each direction of these trees were measured. The survey method

Load Bearing Equipment for Bone and Muscle Project

Science.gov (United States)

Terrier, Douglas; Clayton, Ronald G.; Shackelford, Linda

2015-01-01

Axial skeletal loads coupled with muscle torque forces around joints maintain bone. Astronauts working in pairs to exercise can provide high eccentric loads for each other that are most effective. A prototype of load bearing equipment that will allow astronauts to perform exercises using each other for counter force generation in a controlled fashion and provide eccentric overload is proposed. A frame and attachments that can be rapidly assembled for use and easily stored will demonstrate feasibility of a design that can be adapted for ISS testing and Orion use.

Experimental Investigation of Friction Effect on Liner Model Rolling Bearings for Large Diameter Thrust Bearing Design

Directory of Open Access Journals (Sweden)

S. Babu

2012-12-01

Full Text Available Studying friction coefficient has significant importance, especially when dealing with high load and temperature applications that have frequent starting and stopping points. Towards that, two sets of angular contact Linear Model Mockup Bearings (LMMB were designed and fabricated. This linear model assembly was made up of high precision, grounded raceways (AISI 4140 and commercially purchased balls (AISI 52100. The experimental studies were carried out by placing different number of balls between the raceways under different loads at dry lubricating condition. The static friction coefficients were measured using two different experiments: viz gravitation-based experiment and direct linear force measurement experiment. And Digital Image Correlation (DIC technique was used to find the stiffness of LMMB set.

Assessment of Real-Time Compaction Quality Test Indexes for Rockfill Material Based on Roller Vibratory Acceleration Analysis

Directory of Open Access Journals (Sweden)

Tianbo Hua

2018-01-01

Full Text Available Compaction quality is directly related to the structure and seepage stability of a rockfill dam. To timely and accurately test the compaction quality of the rockfill material, four real-time test indexes were chosen to characterize the soil compaction degree based on the analysis of roller vibratory acceleration, including acceleration peak value (ap, acceleration root mean square value (arms, crest factor value (CF, and compaction meter value (CMV. To determine which of these indexes is the most appropriate, a two-part field compaction experiment was conducted using a vibratory roller in different filling zones of the dam body. Data on rolling parameters, real-time test indexes, and compaction quality indexes were collected to perform statistical regression analyses. Combined with the spectrum analysis of the acceleration signal, it was found that the CF index best characterizes the compaction degree of the rockfill material among the four indexes. Furthermore, the quantitative relations between the real-time index and compaction quality index were established to determine the control criterion of CF, which can instruct the site work of compaction quality control in the rockfill rolling process.

Decreasing inventory of a cement factory roller mill parts using reliability centered maintenance method

Science.gov (United States)

Witantyo; Rindiyah, Anita

2018-03-01

According to data from maintenance planning and control, it was obtained that highest inventory value is non-routine components. Maintenance components are components which procured based on maintenance activities. The problem happens because there is no synchronization between maintenance activities and the components required. Reliability Centered Maintenance method is used to overcome the problem by reevaluating maintenance activities required components. The case chosen is roller mill system because it has the highest unscheduled downtime record. Components required for each maintenance activities will be determined by its failure distribution, so the number of components needed could be predicted. Moreover, those components will be reclassified from routine component to be non-routine component, so the procurement could be carried out regularly. Based on the conducted analysis, failure happens in almost every maintenance task are classified to become scheduled on condition task, scheduled discard task, schedule restoration task and no schedule maintenance. From 87 used components for maintenance activities are evaluated and there 19 components that experience reclassification from non-routine components to routine components. Then the reliability and need of those components were calculated for one-year operation period. Based on this invention, it is suggested to change all of the components in overhaul activity to increase the reliability of roller mill system. Besides, the inventory system should follow maintenance schedule and the number of required components in maintenance activity so the value of procurement will be decreased and the reliability system will increase.

Performance Analysis of Functionally Graded Coatings in Contact with Cylindrical Rollers

Directory of Open Access Journals (Sweden)

Reza Jahedi

2015-01-01

Full Text Available This work presents finite element analysis (FEA and results for rolling contact of a cylindrical roller on an elastic substrate coated by functionally graded material (FGM. The rolling process and the graded coating material property and layers arrangement are modeled using finite element codes which lead to a new methodology. This novel methodology provides a trend in determining surface contact stresses, deformations, contact zones, and energy dissipation through the contact area. Effects of stiffness ratio, friction, and exponentially variation of material property on the contact stresses and deformations are studied. Some of the results are verified with analytical solutions. The study results may be beneficial in graded coated cylindrical components analysis against rolling contact failure and wear.

Failure of the chassis of roller skates for agonistic figure skating

Directory of Open Access Journals (Sweden)

Giorgio Olmi

2015-04-01

Full Text Available The subject of this work was to investigate the early failure, which occurred in the chassis of a roller skate for figure skating. The paper deals with the preliminary analysis of the crack and with the integrated approach, which had to be followed to overcome the problem. Literature in the fields of physiology and biomechanics was studied to correctly simulate the load distribution on the chassis. Finite element simulation, experimental stress analysis and analytical modeling of impact phenomena had to be combined together to estimate the entity of dynamic loads and the corresponding state of stress. The analysis led to the determination of the primary cause of failure, bending fatigue, and to the suggestion of a simple solution to improve and optimize the project.

Field Assessment and Specification Review for Roller-Integrated Compaction Monitoring Technologies

Directory of Open Access Journals (Sweden)

David J. White

2011-01-01

Full Text Available Roller-integrated compaction monitoring (RICM technologies provide virtually 100-percent coverage of compacted areas with real-time display of the compaction measurement values. Although a few countries have developed quality control (QC and quality assurance (QA specifications, broader implementation of these technologies into earthwork construction operations still requires a thorough understanding of relationships between RICM values and traditional in situ point test measurements. The purpose of this paper is to provide: (a an overview of two technologies, namely, compaction meter value (CMV and machine drive power (MDP; (b a comprehensive review of field assessment studies, (c an overview of factors influencing statistical correlations, (d modeling for visualization and characterization of spatial nonuniformity; and (e a brief review of the current specifications.

Grizzly bear

Science.gov (United States)

Schwartz, C.C.; Miller, S.D.; Haroldson, M.A.; Feldhamer, G.; Thompson, B.; Chapman, J.

2003-01-01

The grizzly bear inspires fear, awe, and respect in humans to a degree unmatched by any other North American wild mammal. Like other bear species, it can inflict serious injury and death on humans and sometimes does. Unlike the polar bear (Ursus maritimus) of the sparsely inhabited northern arctic, however, grizzly bears still live in areas visited by crowds of people, where presence of the grizzly remains physically real and emotionally dominant. A hike in the wilderness that includes grizzly bears is different from a stroll in a forest from which grizzly bears have been purged; nighttime conversations around the campfire and dreams in the tent reflect the presence of the great bear. Contributing to the aura of the grizzly bear is the mixture of myth and reality about its ferocity. unpredictable disposition, large size, strength, huge canines, long claws, keen senses, swiftness, and playfulness. They share characteristics with humans such as generalist life history strategies. extended periods of maternal care, and omnivorous diets. These factors capture the human imagination in ways distinct from other North American mammals. Precontact Native American legends reflected the same fascination with the grizzly bear as modern stories and legends (Rockwell 1991).

Estimation of the nuclear fuel assembly eigenfrequencies in the probability sense

Directory of Open Access Journals (Sweden)

Zeman V.

2014-12-01

Full Text Available The paper deals with upper and lower limits estimation of the nuclear fuel assembly eigenfrequencies, whose design and operation parameters are random variables. Each parameter is defined by its mean value and standard deviation or by a range of values. The gradient and three sigma criterion approach is applied to the calculation of the upper and lower limits of fuel assembly eigenfrequencies in the probability sense. Presented analytical approach used for the calculation of eigenfrequencies sensitivity is based on the modal synthesis method and the fuel assembly decomposition into six identical revolved fuel rod segments, centre tube and load-bearing skeleton linked by spacer grids. The method is applied for the Russian TVSA-T fuel assembly in the WWER1000/320 type reactor core in the Czech nuclear power plant Temelín.

Failure Analysis and Recovery of a 50-mm Highly Elastic Intermetallic NiTi Ball Bearing for an ISS Application

Science.gov (United States)

DellaCorte, Christopher; Howard, S. Adam; Moore, Lewis

2016-01-01

Ball bearings used inside the ISS Distillation Assembly centrifuge require superior corrosion and shock resistance to withstand acidic wastewater exposure and heavy spacecraft launch related loads. These requirements challenge conventional steel bearings and provide an ideal pathfinder application for 50-mm bore, deep-groove ball bearings made from the corrosion immune and highly elastic intermetallic material 60NiTi. During early ground testing in 2014 one 60NiTi bearing unexpectedly and catastrophically failed after operating for only 200 hr. A second bearing running on the same shaft was completely unaffected. An investigation into the root cause of the failure determined that an excessively tight press fit of the bearing outer race coupled with NiTi's relatively low elastic modulus were key contributing factors. The proposed failure mode was successfully replicated by experiment. To further corroborate the root cause theory, a successful bearing life test using improved installation practices (selective fitting) was conducted. The results show that NiTi bearings are suitable for space applications provided that care is taken to accommodate their unique material characteristics.

Investigating the process of white etching crack initiation in bearing steel

Energy Technology Data Exchange (ETDEWEB)

Gould, Benjamin; Greco, Aaron

2016-04-01

White etching cracks (WECs) have been identified as a dominant mode of premature failure within wind turbine gearbox bearings. Though WECs have been reported in the field for over a decade, the conditions leading to WECs, and the process by which this failure culminates, are both highly debated. In previously published work, the generation of WECs on a benchtop scale was linked to sliding at the surface of the test sample, it was also postulated that the generation of WECs was dependent on the cumulative energy that had been applied to the sample over the entirety of the test. In this paper, a three ring on roller bench top test rig is used to systematically alter the cumulative energy that a sample experiences through changes in normal load, sliding, and run time, in an attempt to correlate cumulative energy with the formation of WECs. It was determined that, in the current test setup, the presence of WECs can be predicted by this energy criterion. The authors then used this information to study the process by which WECs initiate. Lastly, it was found that, under the current testing conditions, the formation of a dark etching microstructure precedes the formation of a crack, and a crack precedes the formation of white etching microstructure.

design analysis of cam-follower system for beat up motion

African Journals Online (AJOL)

User

A cam swing roller-follower mechanism is designed for the beat-up motion of a horizontal narrow loom. The system consists of a radial plate-cam driven by a camshaft keyed to the plate cam. A slay bar which act as the beater is attached to the radial swing roller-follower and assembled on the plate cam. A continuous ...

77 FR 70423 - Black Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC...

Science.gov (United States)

2012-11-26

... Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC; Notice of..., 2012, Black Bear Hydro Partners, LLC, sole licensee (transferor) and Black Bear Development Holdings, LLC and Black Bear SO, LLC (transferees) filed an application for the partial the transfer of licenses...

Method for Vibration Response Simulation and Sensor Placement Optimization of a Machine Tool Spindle System with a Bearing Defect

Science.gov (United States)

Cao, Hongrui; Niu, Linkai; He, Zhengjia

2012-01-01

Bearing defects are one of the most important mechanical sources for vibration and noise generation in machine tool spindles. In this study, an integrated finite element (FE) model is proposed to predict the vibration responses of a spindle bearing system with localized bearing defects and then the sensor placement for better detection of bearing faults is optimized. A nonlinear bearing model is developed based on Jones' bearing theory, while the drawbar, shaft and housing are modeled as Timoshenko's beam. The bearing model is then integrated into the FE model of drawbar/shaft/housing by assembling equations of motion. The Newmark time integration method is used to solve the vibration responses numerically. The FE model of the spindle-bearing system was verified by conducting dynamic tests. Then, the localized bearing defects were modeled and vibration responses generated by the outer ring defect were simulated as an illustration. The optimization scheme of the sensor placement was carried out on the test spindle. The results proved that, the optimal sensor placement depends on the vibration modes under different boundary conditions and the transfer path between the excitation and the response. PMID:23012514

Phylogeography of mitochondrial DNA variation in brown bears and polar bears.

Science.gov (United States)

Shields, G F; Adams, D; Garner, G; Labelle, M; Pietsch, J; Ramsay, M; Schwartz, C; Titus, K; Williamson, S

2000-05-01

We analyzed 286 nucleotides of the middle portion of the mitochondrial cytochrome b gene of 61 brown bears from three locations in Alaska and 55 polar bears from Arctic Canada and Arctic Siberia to test our earlier observations of paraphyly between polar bears and brown bears as well as to test the extreme uniqueness of mitochondrial DNA types of brown bears on Admiralty, Baranof, and Chichagof (ABC) islands of southeastern Alaska. We also investigated the phylogeography of brown bears of Alaska's Kenai Peninsula in relation to other Alaskan brown bears because the former are being threatened by increased human development. We predicted that: (1) mtDNA paraphyly between brown bears and polar bears would be upheld, (2) the mtDNA uniqueness of brown bears of the ABC islands would be upheld, and (3) brown bears of the Kenai Peninsula would belong to either clade II or clade III of brown bears of our earlier studies of mtDNA. All of our predictions were upheld through the analysis of these additional samples. Copyright 2000 Academic Press.

Phylogeography of mitochondrial DNA variation in brown bears and polar bears

Science.gov (United States)

Shields, Gerald F.; Adams, Deborah; Garner, Gerald W.; Labelle, Martine; Pietsch, Jacy; Ramsay, Malcolm; Schwartz, Charles; Titus, Kimberly; Williamson, Scott

2000-01-01

We analyzed 286 nucleotides of the middle portion of the mitochondrial cytochrome b gene of 61 brown bears from three locations in Alaska and 55 polar bears from Arctic Canada and Arctic Siberia to test our earlier observations of paraphyly between polar bears and brown bears as well as to test the extreme uniqueness of mitochondrial DNA types of brown bears on Admiralty, Baranof, and Chichagof (ABC) islands of southeastern Alaska. We also investigated the phylogeography of brown bears of Alaska's Kenai Peninsula in relation to other Alaskan brown bears because the former are being threatened by increased human development. We predicted that: (1) mtDNA paraphyly between brown bears and polar bears would be upheld, (2) the mtDNA uniqueness of brown bears of the ABC islands would be upheld, and (3) brown bears of the Kenai Peninsula would belong to either clade II or clade III of brown bears of our earlier studies of mtDNA. All of our predictions were upheld through the analysis of these additional samples.

Modelling and design of undercarriage components of large-scale earthmoving equipment in tar sand operations

Energy Technology Data Exchange (ETDEWEB)

Szymanski, J.; Frimpong, S.; Sobieski, R. [Alberta Univ., Edmonton, AB (Canada). Centre for Advanced Energy and Minerals Research

2004-07-01

This presentation described the fundamental and applied research work which has been carried out at the University of Alberta's Centre for Advanced Energy and Minerals Research to improve the undercarriage elements of large scale earthmoving equipment used in oil sands mining operations. A new method has been developed to predict the optimum curvature and blade geometry of earth moving equipment such as bulldozers and motor graders. A mathematical relationship has been found to approximate the optimum blade shape for reducing cutting resistance and fill resistance. The equation is a function of blade geometry and soil properties. It is the first model that can mathematically optimize the shape of a blade on earth moving equipment. A significant saving in undercarriage components can be achieved from reducing the amount of cutting and filling resistance for this type of equipment working on different soils. A Sprocket Carrier Roller for a Tracked Vehicle was also invented to replace the conventional cylindrical carrier roller. The new sprocket type carrier roller offers greater support for the drive track and other components of the undercarriage assembly. A unique retaining pin assembly has also been designed to detach connecting disposable wear parts from earthmoving equipment. The retaining pin assembly is easy to assemble and disassemble and includes reusable parts. 13 figs.

Edge coating apparatus with movable roller applicator for solar cell substrates

Science.gov (United States)

Pavani, Luca; Abas, Emmanuel

2012-12-04

A non-contact edge coating apparatus includes an applicator for applying a coating material on an edge of a solar cell substrate and a control system configured to drive the applicator. The control system may drive the applicator along an axis to maintain a distance with an edge of the substrate as the substrate is rotated to have the edge coated with a coating material. The applicator may include a recessed portion into which the edge of the substrate is received for edge coating. For example, the applicator may be a roller with a groove. Coating material may be introduced into the groove for application onto the edge of the substrate. A variety of coating materials may be employed with the apparatus including hot melt ink and UV curable plating resist.

Multivariable H force/level control of the twin-roller strip caster

International Nuclear Information System (INIS)

Cavazos, A.; Edwards, J.B.

2005-01-01

Twin-roller steel strip casters may offer some advantages with respect to classical continuous casting hot rolling processes. Some works have reported control aspects of this process and although the process has been found to be highly interactive and non-linear, little or no attention has been given to its multivariable characteristics. The purpose of this work is to design a multivariable control capable of decoupling the system. This paper presents some important aspects of the strip caster modeling and reports the simulation results of the application of the multivariable H-optimal control for nominal performance to force/level control. Various controllers have been designed for different pool level heights and it is shown that they can decouple the system, allowing the application of PI decentralized controllers to considerably improve performance. (author)

Introgressive hybridization: brown bears as vectors for polar bear alleles.

Science.gov (United States)

Hailer, Frank

2015-03-01

The dynamics and consequences of introgression can inform about numerous evolutionary processes. Biologists have therefore long been interested in hybridization. One challenge, however, lies in the identification of nonadmixed genotypes that can serve as a baseline for accurate quantification of admixture. In this issue of Molecular Ecology, Cahill et al. (2015) analyse a genomic data set of 28 polar bears, eight brown bears and one American black bear. Polar bear alleles are found to be introgressed into brown bears not only near a previously identified admixture zone on the Alaskan Admiralty, Baranof and Chichagof (ABC) Islands, but also far into the North American mainland. Elegantly contrasting admixture levels at autosomal and X chromosomal markers, Cahill and colleagues infer that male-biased dispersal has spread these introgressed alleles away from the Late Pleistocene contact zone. Compared to a previous study on the ABC Island population in which an Alaskan brown bear served as a putatively admixture-free reference, Cahill et al. (2015) utilize a newly sequenced Swedish brown bear as admixture baseline. This approach reveals that brown bears have been impacted by introgression from polar bears to a larger extent (up to 8.8% of their genome), than previously known, including the bear that had previously served as admixture baseline. No evidence for introgression of brown bear into polar bear is found, which the authors argue could be a consequence of selection. Besides adding new exciting pieces to the puzzle of polar/brown bear evolutionary history, the study by Cahill and colleagues highlights that wildlife genomics is moving from analysing single genomes towards a landscape genomics approach. © 2015 John Wiley & Sons Ltd.

Investigation of bearing inner ring-cage thermal characteristics based on CdTe quantum dots fluorescence thermometry

International Nuclear Information System (INIS)

Yan, Ke; Yan, Bei; Li, Ben Q.; Hong, Jun

2017-01-01

Highlights: • A novel method for bearing inner ring/cage thermal monitoring was first presented. • Temperature rise of bearing inner ring in real work condition was obtained. • The rotation speed (6000 r/min) measured here is much higher than all the existing methods. - Abstract: A novel wireless temperature sensor and non-intrusive temperature measurement method for bearing monitoring were proposed in this paper, based on spectrum parameter analysis of CdTe quantum dots films. The CdTe QDs were synthesized and were used in constructing of a sensor film by means of Layer-by-layer Electrostatic Self-assembly method. The fluorescence spectrum properties of the sensor were characterized. At rotation speed 5000–6000 r/min, bearing cage and inner ring temperature were presented first in this paper by the CdTe QDs sensor. The results were verified by theoretical analysis and by thermocouples, with an error typically below 10% or smaller. Compared to the traditional outer ring monitoring, the measurement and monitoring of bearing rolling elements is of very importance, especially at high rotation speed.

Electromagnetic brake/clutch device

Science.gov (United States)

Vranish, John M. (Inventor)

1994-01-01

An electromagnetic brake/clutch device includes a drive shaft supported by at least one bearing for transmitting torque, a housing, affixed to prevent its rotation, surrounding the drive shaft, and an electromagnetically activated device within the housing to selectively prevent and allow rotation of the drive shaft. The electromagnetically activated device includes a plurality of cammed rollers to prevent counter-clockwise rotation of the drive shaft. The drive shaft includes a circumferential disk and the housing includes a reaction ring for engagement with the plurality of cammed rollers. The plurality of cammed rollers are released from engagement with the circumferential disk and the reaction ring by a plurality of tripping mechanisms within the housing. The tripping action uses the locking force to act as a release force merely by changing the boundary conditions of the roller interface angles. The tripping mechanisms include trippers for disengaging the plurality of cammed rollers and an anvil shaped portion for providing lateral movement of the trippers. The plurality of cammed rollers is preloaded to engagement with the circumferential disk and reaction ring by a spring, and is located with respect to an adjacent tripping mechanism with another spring.

Effect of the variation in the ambient moisture on the compaction behavior of powder undergoing roller-compaction and on the characteristics of tablets produced from the post-milled granules.

Science.gov (United States)

Gupta, Abhay; Peck, Garnet E; Miller, Ronald W; Morris, Kenneth R

2005-10-01

Effect of variation in the ambient moisture levels on the compaction behavior of a 10% acetaminophen (APAP) powder blend in microcrystalline cellulose (MCC) powder was studied by comparing the physical and mechanical properties of ribbons prepared by roller compaction with those of simulated ribbons, i.e., tablets prepared under uni-axial compression. Relative density, moisture content, tensile strength, and Young's modulus were used as key compact properties for comparison. Moisture was found to facilitate the particle rearrangement of both, the APAP and the MCC particles, as well as the deformation of the MCC particles. The tensile strength of the simulated ribbons also showed an increase with increasing moisture content. An interesting observation was that the tensile strength of the roller compacted samples first increased and then decreased with increasing moisture content. Variation in the ambient moisture during roller compaction was also found to influence the characteristics of tablets produced from the granules obtained post-milling the ribbons. A method to study this influence is also reported. Copyright (c) 2005 Wiley-Liss, Inc. and the American Pharmacists Association

Macular hemorrhage after roller coaster riding in a single-eyed patient with congenital glaucoma

Directory of Open Access Journals (Sweden)

Dilek Guven

Full Text Available ABSTRACT A 21-year-old female presented with a 4-day history of decreased vision in her only functional eye (right eye, OD. She had a history of multiple ocular surgeries in both eyes because of congenital glaucoma and had lost light perception in her left eye several years prior. Ophthalmological examination revealed 0.15 Snellen visual acuity, and fundoscopy revealed nearly total cupping and pallor of the optic disc and multiple retinal hemorrhagic foci in the macula in OD. Lesions spontaneously resolved over a few months. Gravitational forces during a roller coaster ride may have caused this macular hemorrhage.

Kinematic and dynamic modeling and approximate analysis of a roller chain drive

DEFF Research Database (Denmark)

Fuglede, Niels; Thomsen, Jon Juel

2016-01-01

for analytical studies of the coupled motion of the chain spans and driven sprocket. Parametric excitation of the spans come from sprocket angular displacements, and the driven sprocket acts as a boundary which can be compliant in the axial direction. External transverse excitation of the spans comes from...... polygonal action, and is treated through kinematic forcing at the moving string boundaries. Perturbation analysis of the model is carried out using the method of multiple scales. Results show a multitude of internal and external resonance conditions, and some examples are presented of both decoupled...... and coupled motion. Together, the kinematic and dynamic model are aimed toward providing a framework for conducting and understanding both numerical, and experimental investigations of roller chain drive dynamics....

EcoBears

DEFF Research Database (Denmark)

Nielsen, Nick; Pedersen, Sandra Bleuenn; Sørensen, Jens Ager

2015-01-01

In this paper, we introduce the EcoBears concept that aims to augment household appliances with functional and aesthetic features to promote their "use'' and "longevity of use'' to prevent their disposal. The EcoBears also aim to support the communication of environmental issues in the home setting....... We present our initial design and implementation of the EcoBears that consist of two bear modules (a mother and her cub). We also present our preliminary concept validations and lessons learned to be considered for future directions....

Dropout Reasons in Iranian Youth Roller Skaters

Directory of Open Access Journals (Sweden)

Hosein H E Y D A R I

2014-12-01

Full Text Available The main drop - out reasons from the sport of roller skating amongst Iranian youth skaters has been examined. A questionnaire with 53 items (adopted from Enoksen, 2011 representing seven subscales namel y: training factors and facilities, executive factors and team, education and work obligations, motivational aspects, social - cultural environment, choice of other sport activities and interests and economic factors was especially developed for this researc h. Responses were measured on a Likert scale ranging from “strongly disagree” to “strongly agree” in relation to each statement. In all 11 2 skaters predominantly male (mean age 17.1, SD = 1.63 with a mean = 5.43 years of experience (SD = 2.92 that had di scontinued in the past two years completed the questionnaire. Results of one sample t - tests showed that all factors expect “social - cultural environment” are significant indicators for drop out from skating with “economical factors” scoring the highest rank ing. Correlational analysis showed that younger participants agree more strongly th at “executive factors and team” and “education and work obligations” were the best predictors of drop out. Those with fewer years of experience considered “training factors and facilities”, “motivational aspects and social and cultural environment” as more likely reasons for quitting. Implications of the findings are discussed.

Quantitative evaluation of hand cranking a roller pump in a crisis management drill.

Science.gov (United States)

Tomizawa, Yasuko; Tokumine, Asako; Ninomiya, Shinji; Momose, Naoki; Matayoshi, Toru

2008-01-01

The heart-lung machines for open-heart surgery have improved over the past 50 years; they rarely break down and are almost always equipped with backup batteries. The hand-cranking procedure only becomes necessary when a pump breaks down during perfusion or after the batteries have run out. In this study, the performance of hand cranking a roller pump was quantitatively assessed by an objective method using the ECCSIM-Lite educational simulator system. A roller pump connected to an extracorporeal circuit with an oxygenator and with gravity venous drainage was used. A flow sensor unit consisting of electromagnetic sensors was used to measure arterial and venous flow rates, and a built-in pressure sensor was used to measure the water level in the reservoir. A preliminary study of continuous cranking by a team of six people was conducted as a surprise drill. This system was then used at a perfusion seminar. At the seminar, 1-min hand-cranking drills were conducted by volunteers according to a prepared scenario. The data were calculated on site and trend graphs of individual performances were given to the participants as a handout. Preliminary studies showed that each person's performance was different. Results from 1-min drills showed that good performance was not related to the number of clinical cases experienced, years of practice, or experience in hand cranking. Hand cranking to maintain the target flow rate could be achieved without practice; however, manipulating the venous return clamp requires practice. While the necessity of performing hand cranking during perfusion due to pump failure is rare, we believe that it is beneficial for perfusionists and patients to include hand-cranking practice in periodic extracorporeal circulation crisis management drills because a drill allows perfusionists to mentally rehearse the procedures should such a crisis occur.

Acute Lameness in a Roller Pigeon ( Columba livia ) with Multicentric Lymphosarcoma.

Science.gov (United States)

Williams, Susan M; Williams, Robert J; Gogal, Robert M

2017-06-01

A 3-yr-old adult female roller pigeon ( Columba livia ) used as part of a breeding pair for an ongoing research study presented with acute left limb lameness. Palpation of the left leg and region revealed a large lump near the coxofemoral joint. The bird was able to ambulate in the cage, but would not brood her hatchling. The bird was humanely euthanized and necropsy was performed. Grossly, multiple large white to pale tan nodules were noted in the pancreas, lung, rib cage, intestines, and unilaterally in the left kidney. Microscopic examination of the various organs revealed neoplastic proliferation of round cells consistent with lymphoblasts. Immunohistochemistry was performed with the use of antibodies to CD3, CD79a, CD20, and CD21 to phenotype the cells. The results indicated that the neoplastic infiltrating cells were predominantly of T-cell origin.

The physiological and biomechanical contributions of poling to roller ski skating.

Science.gov (United States)

Sandbakk, Øyvind; Ettema, Gertjan; Holmberg, Hans-Christer

2013-08-01

Poling is considered to make a significant contribution to cross-country skiing with the skating technique. To better understand this contribution, the current investigation compared roller ski skating on a treadmill with the so-called G3 skating technique with (G3-P) and without poling (G3-NP). Seven male elite skiers performed 5-min submaximal tests at 8, 12, and 15 km h(-1), as well as an incremental test to exhaustion with both techniques on a 5 % incline. Ventilatory variables were assessed by open-circuit indirect calorimetry and three-dimensional kinematics analyzed using the Qualisys Pro Reflex system. G3-P was associated with approximately 15 % higher peak velocity and 10 % higher peak oxygen uptake than G3-NP in the incremental test (both P skating, specifically by enhancing peak oxygen uptake, skiing efficiency and associated biomechanical variables.

Stable isotopes to detect food-conditioned bears and to evaluate human-bear management

Science.gov (United States)

Hopkins, John B.; Koch, Paul L.; Schwartz, Charles C.; Ferguson, Jake M.; Greenleaf, Schuyler S.; Kalinowski, Steven T.

2012-01-01

We used genetic and stable isotope analysis of hair from free-ranging black bears (Ursus americanus) in Yosemite National Park, California, USA to: 1) identify bears that consume human food, 2) estimate the diets of these bears, and 3) evaluate the Yosemite human–bear management program. Specifically, we analyzed the isotopic composition of hair from bears known a priori to be food-conditioned or non-food-conditioned and used these data to predict whether bears with an unknown management status were food-conditioned (FC) or non-food-conditioned (NFC). We used a stable isotope mixing model to estimate the proportional contribution of natural foods (plants and animals) versus human food in the diets of FC bears. We then used results from both analyses to evaluate proactive (population-level) and reactive (individual-level) human–bear management, and discussed new metrics to evaluate the overall human–bear management program in Yosemite. Our results indicated that 19 out of 145 (13%) unknown bears sampled from 2005 to 2007 were food-conditioned. The proportion of human food in the diets of known FC bears likely declined from 2001–2003 to 2005–2007, suggesting proactive management was successful in reducing the amount of human food available to bears. In contrast, reactive management was not successful in changing the management status of known FC bears to NFC bears, or in reducing the contribution of human food to the diets of FC bears. Nine known FC bears were recaptured on 14 occasions from 2001 to 2007; all bears were classified as FC during subsequent recaptures, and human–bear management did not reduce the amount of human food in the diets of FC bears. Based on our results, we suggest Yosemite continue implementing proactive human–bear management, reevaluate reactive management, and consider removing problem bears (those involved in repeated bear incidents) from the population.

State Space Formulation of Nonlinear Vibration Responses Collected from a Dynamic Rotor-Bearing System: An Extension of Bearing Diagnostics to Bearing Prognostics.

Science.gov (United States)

Tse, Peter W; Wang, Dong

2017-02-14

Bearings are widely used in various industries to support rotating shafts. Their failures accelerate failures of other adjacent components and may cause unexpected machine breakdowns. In recent years, nonlinear vibration responses collected from a dynamic rotor-bearing system have been widely analyzed for bearing diagnostics. Numerous methods have been proposed to identify different bearing faults. However, these methods are unable to predict the future health conditions of bearings. To extend bearing diagnostics to bearing prognostics, this paper reports the design of a state space formulation of nonlinear vibration responses collected from a dynamic rotor-bearing system in order to intelligently predict bearing remaining useful life (RUL). Firstly, analyses of nonlinear vibration responses were conducted to construct a bearing health indicator (BHI) so as to assess the current bearing health condition. Secondly, a state space model of the BHI was developed to mathematically track the health evolution of the BHI. Thirdly, unscented particle filtering was used to predict bearing RUL. Lastly, a new bearing acceleration life testing setup was designed to collect natural bearing degradation data, which were used to validate the effectiveness of the proposed bearing prognostic method. Results show that the prediction accuracy of the proposed bearing prognostic method is promising and the proposed bearing prognostic method is able to reflect future bearing health conditions.

State Space Formulation of Nonlinear Vibration Responses Collected from a Dynamic Rotor-Bearing System: An Extension of Bearing Diagnostics to Bearing Prognostics

Directory of Open Access Journals (Sweden)

Peter W. Tse

2017-02-01

Full Text Available Bearings are widely used in various industries to support rotating shafts. Their failures accelerate failures of other adjacent components and may cause unexpected machine breakdowns. In recent years, nonlinear vibration responses collected from a dynamic rotor-bearing system have been widely analyzed for bearing diagnostics. Numerous methods have been proposed to identify different bearing faults. However, these methods are unable to predict the future health conditions of bearings. To extend bearing diagnostics to bearing prognostics, this paper reports the design of a state space formulation of nonlinear vibration responses collected from a dynamic rotor-bearing system in order to intelligently predict bearing remaining useful life (RUL. Firstly, analyses of nonlinear vibration responses were conducted to construct a bearing health indicator (BHI so as to assess the current bearing health condition. Secondly, a state space model of the BHI was developed to mathematically track the health evolution of the BHI. Thirdly, unscented particle filtering was used to predict bearing RUL. Lastly, a new bearing acceleration life testing setup was designed to collect natural bearing degradation data, which were used to validate the effectiveness of the proposed bearing prognostic method. Results show that the prediction accuracy of the proposed bearing prognostic method is promising and the proposed bearing prognostic method is able to reflect future bearing health conditions.

Energy-saving belt conveyors installed in Polish collieries

Directory of Open Access Journals (Sweden)

Jerzy ANTONIAK

2010-01-01

Full Text Available An important problem of reducing energy consumption and dioxide emissions in the stage of construction and operation of mine belt conveyors is connected with their broad use in the industry. However, this notion is related to a reduction of electric energy consumption for conveyor drive and for production of conveyor components and assemblies (belts, rollers, load-bearing structure etc.. An essential role is played by an increased life of belt conveyors assemblies and components, principally belts. A reduced electric energy consumption results in a decreased CO2 emissions, e.g. hard coal – fired power station issues 0.28 kg CO2 per production of 1 kWh, in to answer production of 1 t steel accounts for 3.2 t CO2 emissions. The subject-matter presented in the paper concerning energy-saving in the horizontally and inclined mine belt conveyors installed in a Polish colliery – Anna, Jankowice and Marcel, has a big economic significance and it is important from the point of view of environmental protection.

Fatigue methodology for life predictions for the wheel-rail contact area in large offshore turret bearings

Directory of Open Access Journals (Sweden)

T. Lassen

2016-10-01

Full Text Available The present report presents a fatigue life prediction method for large roller bearings applied in the turret turn table for large loading buoy units. The contact points between wheel and rail in these bearings are subjected to a multi-axial fluctuating stress situation and both surface wear and fatigue cracking may occur. A methodology based on the Dang Van fatigue criterion is adopted. The criterion is based on an equivalent stress defined as a combination of the fluctuation of the shear stress from its mean value at a critical plane and the associated hydrostatic stress at the given time. The present work is supporting the theoretical model by extensive laboratory testing. Both full scale testing of wheel on rail and small scale testing for characterizing the steel material are carried out. An experimental program was carried out with the high strength stainless steel S165M. The Dang Van stress concept is applied in combination with the Random Fatigue Limit Method (RFLM for life data analyses. This approach gives the opportunity to include both finite lives and the run-outs in a rational manner without any presumption of the existence of a fatigue limit in advance of the data. This gives a non-linear S-N curve for a log-log scale in the very high cycle regime close to the fatigue limit. It is demonstrated how the scatter in fatigue limit decreases when the Dang Van stress concept is applied and that the fatigue limit is occurring beyond 107 cycles

Comparison of Alignment Correction Angles Between Fixed-Bearing and Mobile-Bearing UKA.

Science.gov (United States)

Inoue, Atsuo; Arai, Yuji; Nakagawa, Shuji; Inoue, Hiroaki; Yamazoe, Shoichi; Kubo, Toshikazu

2016-01-01

Good outcomes have been reported with both fixed-bearing and mobile-bearing unicompartmental knee arthroplasty (UKA). However, overcorrected alignment could induce the progression of arthritis on the non-arthroplasty side. Changes of limb alignment after UKA with both types of bearings (fixed bearing: 24 knees, mobile bearing: 28 knees) were investigated. The mean difference between the preoperative standing femoral-tibial angle (FTA) and postoperative standing FTA was significantly larger in mobile bearing UKA group. In fixed-bearing UKA, there must be some laxity in MCL tension so that a 2-mm tension gauge can be inserted. In mobile-bearing UKA, appropriate MCL tension is needed to prevent bearing dislocation. This difference in MCL tension may have caused the difference in the correction angle between the groups. Copyright © 2016 Elsevier Inc. All rights reserved.

MATHEMATICAL AND COMPUTER MODELING OF AUTOMATIC CONTROL SYSTEM FOR HYDROSTATIC BEARING

Directory of Open Access Journals (Sweden)

N. A. Pelevin

2016-09-01

Full Text Available The paper presents simulation results of hydrostatic bearing dynamics in spindle assembly of standard flexible production module with throttled circuit. The necessity of dynamic quality increase for automatic control system of the hydrostatic bearing with the use of correcting means in the form of RC-chains is shown. The features of correction parameters choice coming from the existence of the crossing connections in automatic control system structure are noted. We propose the block diagram of automatic control system of the hydrostatic bearing in Simulink working field and cyclic algorithm for determination program of RC-chain parameters implemented in MATLAB taking into account typical thermal processes for the finishing treatment. Graphic-analytical method for the correction parameters choice is presented based on the stability stock phase gradient for dynamic quality determination of automatic control system. Researches of the method estimability in case of using the standard metal bellow valve as the hydrocapacity for RC-chain are also carried out. Recommendations for the bellow valve choice are formulated. The check of dynamic quality indicators concerning transition processes calculated by means of the appropriate programs developed for MATLAB is performed. Examples are given for phase stability factor gradient schedules with partition of various areas of hydrostatic bearing dynamic quality for different frequencies of spindle rotation and procedure description of data cursor function application on MATLAB toolbar. Improvement of hydrostatic bearing dynamics under typical low loadings for finishing treatment is noted. Also, decrease of dynamic indicators for high loadings treatment in case of roughing treatment is marked.

Roller compaction: Effect of morphology and amorphous content of lactose powder on product quality.

Science.gov (United States)

Omar, Chalak S; Dhenge, Ranjit M; Osborne, James D; Althaus, Tim O; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

2015-12-30

The effect of morphology and amorphous content, of three types of lactose, on the properties of ribbon produced using roller compaction was investigated. The three types of lactose powders were; anhydrous SuperTab21AN, α-lactose monohydrate 200 M, and spray dried lactose SuperTab11SD. The morphology of the primary particles was identified using scanning electron microscopy (SEM) and the powder amorphous content was quantified using NIR technique. SEM images showed that 21AN and SD are agglomerated type of lactose whereas the 200 M is a non-agglomerated type. During ribbon production, an online thermal imaging technique was used to monitor the surface temperature of the ribbon. It was found that the morphology and the amorphous content of lactose powders have significant effects on the roller compaction behaviour and on ribbon properties. The agglomerated types of lactose produced ribbon with higher surface temperature and tensile strength, larger fragment size, lower porosity and lesser fines percentages than the non-agglomerated type of lactose. The lactose powder with the highest amorphous content showed to result in a better binding ability between the primary particles. This type of lactose produced ribbons with the highest temperature and tensile strength, and the lowest porosity and amount of fines in the product. It also produced ribbon with more smooth surfaces in comparison to the other two types of lactose. It was noticed that there is a relationship between the surface temperature of the ribbon during production and the tensile strength of the ribbon; the higher the temperature of the ribbon during production the higher the tensile strength of the ribbon. Copyright © 2015 Elsevier B.V. All rights reserved.

Establishment of Approximate Analytical Model of Oil Film Force for Finite Length Tilting Pad Journal Bearings

Directory of Open Access Journals (Sweden)

Yongliang Wang

2015-01-01

Full Text Available Tilting pad bearings offer unique dynamic stability enabling successful deployment of high-speed rotating machinery. The model of dynamic stiffness, damping, and added mass coefficients is often used for rotordynamic analyses, and this method does not suffice to describe the dynamic behaviour due to the nonlinear effects of oil film force under larger shaft vibration or vertical rotor conditions. The objective of this paper is to present a nonlinear oil force model for finite length tilting pad journal bearings. An approximate analytic oil film force model was established by analysing the dynamic characteristic of oil film of a single pad journal bearing using variable separation method under the dynamic π oil film boundary condition. And an oil film force model of a four-tilting-pad journal bearing was established by using the pad assembly technique and considering pad tilting angle. The validity of the model established was proved by analyzing the distribution of oil film pressure and the locus of journal centre for tilting pad journal bearings and by comparing the model established in this paper with the model established using finite difference method.

Nuclear reactor fuel assembly spacer grid

International Nuclear Information System (INIS)

Jabsen, F.S.

1977-01-01

A spacer grid for a nuclear fuel assembly is comprised of a lattice of grid plates forming multiple cells that are penetrated by fuel elements. Resilient protrusions and rigid protrusions projecting into the cells from the plates bear against the fuel element to effect proper support and spacing. Pairs of intersecting grid plates, disposed in a longitudinally spaced relationship, cooperate with other plates to form a lattice wherein each cell contains adjacent panels having resilient protrusions arranged opposite adjacent panels having rigid protrusions. The peripheral band bounding the lattice is provided solely with rigid protrusions projecting into the peripheral cells. (Auth.)

Cylinder deactivation for valve trains with roller finger follower; Zylinderabschaltung fuer Ventiltriebe mit Rollenschlepphebeln

Energy Technology Data Exchange (ETDEWEB)

Hoffmann, Hermann; Loch, Adam; Widmann, Richard [Mahle International GmbH, Stuttgart (Germany). Zentrale Voraussentwicklung; Kreussen, Gerhard; Rebbert, Martin [FEV Motorentechnik GmbH, Aachen (Germany). Abt. Dynamik; Meehsen, Daniel [FEV Motorentechnik GmbH, Aachen (Germany). Abt. Mechanik Versuch

2009-04-15

Cylinder deactivation increases efficiency of gasoline engines without negative effects in terms of exhaust gas emissions or driving dynamics. In particular, the advantageous cost/benefit ratio and great affinity to technologies currently used in gasoline engines support cylinder deactivation as the right path in meeting future market demands. The design and function of cylinder deactivation for valve trains with roller finger follower will be explained and examined with regard to functional aspects, such as stiffness, mass, and kinematic behavior. Based on initial results, design and production characteristics of this new technology are evaluated and technical control interactions in engine applications are presented by Mahle. (orig.)

Modeling gadolinium-bearing fuel in Ringhals PWRs using CASMO/SIMULATE

International Nuclear Information System (INIS)

Kurcyusz, E.

1993-01-01

Ringhals units 2, 3, and 4 are Westinghouse three-loop, 157-assembly pressurized water reactors (PWRs) operated by Vattenfall. Originally, all three reactors were loaded in an out-in scheme using reload fuel without burnable poisons. In recent cycles, gadolinium-bearing fuel was introduced to enable a low-leakage loading pattern and minimize fuel cycle costs. This paper focuses on the Fragema 17 x 17 AFA design with peripheral gadolinium rods loaded in units 3 and 4. The Ringhals units are modeled using the Studsvik core management system, consisting of the CASMO-3 transport theory lattice physics code,and the SIMULATE-3 advanced nodal reactor analysis code. The results of the studies verifying the accuracy of CASMO-3/SIMULATE-3 on the assemblies with peripheral gadolinium rods are presented in this paper. The verification was carried out against CASMO-3 color-set calculations and measured reactor data

Abrasion Resistance of Nano Silica Modified Roller Compacted Rubbercrete: Cantabro Loss Method and Response Surface Methodology Approach

Science.gov (United States)

Adamu, Musa; Mohammed, Bashar S.; Shafiq, Nasir

2018-04-01

Roller compacted concrete (RCC) when used for pavement is subjected to skidding/rubbing by wheels of moving vehicles, this causes pavement surface to wear out and abrade. Therefore, abrasion resistance is one of the most important properties of concern for RCC pavement. In this study, response surface methodology was used to design, evaluate and analyze the effect of partial replacement of fine aggregate with crumb rubber, and addition of nano silica on the abrasion resistance of roller compacted rubbercrete (RCR). RCR is the terminology used for RCC pavement where crumb rubber was used as partial replacement to fine aggregate. The Box-Behnken design method was used to develop the mixtures combinations using 10%, 20%, and 30% crumb rubber with 0%, 1%, and 2% nano silica. The Cantabro loss method was used to measure the abrasion resistance. The results showed that the abrasion resistance of RCR decreases with increase in crumb rubber content, and increases with increase in addition of nano silica. The analysis of variance shows that the model developed using response surface methodology (RSM) has a very good degree of correlation, and can be used to predict the abrasion resistance of RCR with a percentage error of 5.44%. The combination of 10.76% crumb rubber and 1.59% nano silica yielded the best combinations of RCR in terms of abrasion resistance of RCR.

Examination of a failed reactor coolant pump rotating assembly from Crystal River Unit 3

International Nuclear Information System (INIS)

Hayner, G.O.; Lubnow, T.; Clary, M.

1990-01-01

On January 18, 1989, the A reactor coolant pump rotating assembly at the Crystal River Unit 3 Nuclear Power Plant failed during operation. A rotating assembly from this pump had previously failed in 1986. The reactor coolant pump was fabricated by Byron Jackson Pump Division of Borg-Warner Ind. Products, Inc. from UNS S66286 superalloy (Alloy A286). A root cause failure analysis examination was performed on the pump shaft and other components. The failure analysis included shaft vibrational mode and stress analyses, pump clearance and alignment analyses, and detailed destructive examination of the shaft and hydrostatic bearing assemblies. Based on the detailed physical examination of the shaft it was concluded that cracks initiated in the pump shaft at two sites approximately 180 0 apart in a band of shallow, thermally induced fatigue cracks. The cracks initiated at the bottom edge of the motor end shrink fit pad under the shrink fit sleeve supporting the hydrostatic bearing journal. The band of thermally induced fatigue cracks was apparently caused by mixing of cold seal injection water and hot reactor coolant in gaps between the pump shaft and sleeve. The motor end shrink fit was apparently not effective in preventing introduction of the seal injection water to this area. Initial crack propagation occurred by fatigue due to lateral vibration; however, the majority of crack propagation occurred by abnormal torsional fatigue loading induced by contact and sticking between the rotating and stationary portions of the hydrostatic bearing. Final fracture of the shaft occurred by torsional overload. Metallurgical characteristics and mechanical properties of the shaft were within design specification and probably did not significantly influence the cracking process

A review of bear farming and bear trade in Lao People's Democratic Republic

Directory of Open Access Journals (Sweden)

E. Livingstone

2018-01-01

Full Text Available This study reviews the bear farming industry in Lao PDR with the objective of documenting the current number of commercial bear facilities (i.e. captive bear facilities judged to be trading in bear bile and/or bears and bear parts and the number of bears contained within these facilities, noting changes since it was last examined between 2000 and 2012 by Livingstone and Shepherd (2014. We surveyed all known commercial bear facilities and searched for previously unrecorded facilities. We compared our records with Livingstone and Shepherd (2014 and corrected some duplicate records from their study. In 2017, we recorded seven commercial facilities; four dedicated bear farms, and three tiger farms that were reportedly also keeping bears. We found that between 2012 and 2017 the recorded number of dedicated bear farms reduced by two, and the recorded number of tiger farms also keeping bears increased by one. Within the same period, the total number of captive bears among all facilities in Lao PDR hardly changed (+one, but the number of bears within each facility did. The northern facilities, owned by ethnic Chinese, have expanded since 2012, and central and southern facilities have downsized or closed. While bear farming appears to be downsizing in Lao PDR overall, efforts to phase it out are undermined by the expansion of foreign owned facilities in the north, within Special and Specific Economic Zones that largely cater to a Chinese market, and where the Lao government's efforts to enforce laws and protect wildlife appear to be lacking. Closing the facilities in the north will require political will and decisive law enforcement. Keywords: Bear farms, Bear bile, Gall bladder, Urso-deoxycholic acid, Bear bile extraction facilities, Lao PDR, Ursus thibetanus

Hot roller embossing system equipped with a temperature margin-based controller

Energy Technology Data Exchange (ETDEWEB)

Kim, Seyoung, E-mail: seyoungkim@kimm.re.kr; Son, Youngsu; Lee, Sunghee; Ham, Sangyong; Kim, Byungin [Department of Robotics and Mechatronics, Korea Institute of Machinery and Materials (KIMM), Daejeon (Korea, Republic of)

2014-08-15

A temperature control system was proposed for hot roller embossing. The roll surface was heated using induction coils and cooled with a circulating chilled water system. The temperature of the roll surface was precisely controlled by a temperature margin-based control algorithm that we developed. Implementation of the control system reduced deviations in the roll surface temperature to less than ±2 °C. The tight temperature control and the ability to rapidly increase and decrease the roll temperature will allow optimum operating parameters to be developed quickly. The temperature margin-based controller could also be used to optimize the time course of electrical power and shorten the cooling time by choosing an appropriate temperature margin, possibly for limited power consumption. The chiller-equipped heating roll with the proposed control algorithm is expected to decrease the time needed to determine the optimal embossing process.

New roller cone bits with unique nozzle designs reduce drilling costs

International Nuclear Information System (INIS)

Moffitt, S.R.; Pearce, D.E.; Ivie, C.R.

1992-01-01

This paper reports that selection of the optimum rock bit design to achieve the lowest drilling cost in a given application is often difficult due to a large number of rock bit performance considerations. However, in a majority of applications increased penetration rate is the key consideration in reducing drilling costs. Discovery of a new bit design concept has led to the development of roller cone bits that achieve significant penetration rate increases using superior hydraulic nozzle designs. Prototype designs have achieved 20 to 40% increases in penetration rate with comparable footage drilled when tested in 6 1/2, 8 1/2, 8-3/4, 9-7/8 and 12 1/4 IADC 437, 517 and 537 type bits in the U.S., North Sea, Italy, and Oman. Second-generation designs tested in a full-scale drilling laboratory have delivered 70% increases in penetration rates

Hot roller embossing system equipped with a temperature margin-based controller

International Nuclear Information System (INIS)

Kim, Seyoung; Son, Youngsu; Lee, Sunghee; Ham, Sangyong; Kim, Byungin

2014-01-01

A temperature control system was proposed for hot roller embossing. The roll surface was heated using induction coils and cooled with a circulating chilled water system. The temperature of the roll surface was precisely controlled by a temperature margin-based control algorithm that we developed. Implementation of the control system reduced deviations in the roll surface temperature to less than ±2 °C. The tight temperature control and the ability to rapidly increase and decrease the roll temperature will allow optimum operating parameters to be developed quickly. The temperature margin-based controller could also be used to optimize the time course of electrical power and shorten the cooling time by choosing an appropriate temperature margin, possibly for limited power consumption. The chiller-equipped heating roll with the proposed control algorithm is expected to decrease the time needed to determine the optimal embossing process

Teddy Bear Stories

DEFF Research Database (Denmark)

van Leeuwen, Theo; Caldas-Coulthardt, Carmen

2014-01-01

This paper presents a semiotic analysis of a key cultural artefact, the teddy bear. After introducing the iconography of the teddy bear, it analyses different kinds of stories to show how teddy bears are endowed with meaning in everyday life: stories from children's books, reminiscenses by adults...... bears have traditionally centred on interpersonal relations within the nuclear family, but have recently been institutionalized and commercialized....

LIGHT-WEIGHT LOAD-BEARING STRUCTURES REINFORCED BY CORE ELEMENTS MADE OF SEGMENTS AND A METHOD OF CASTING SUCH STRUCTURES

DEFF Research Database (Denmark)

2009-01-01

The invention relates to a light-weight load-bearing structure, reinforced by core elements (2) of a strong material constituting one or more compression or tension zones in the structure to be cast, which core (2) is surrounded by or adjacent to a material of less strength compared to the core (2......), where the core (2) is constructed from segments (1) of core elements (2) assembled by means of one or more prestressing elements (4). The invention further relates to a method of casting of light-weight load-bearing structures, reinforced by core elements (2) of a strong material constituting one...... or more compression or tension zones in the structure to be cast, which core (2) is surrounded by or adjacent to a material of less strength compared to the core (2), where the core (2) is constructed from segments (1) of core elements (2) assembled and hold together by means of one or more prestressing...

Fuel assembly design for APR1400 with low CBC

Energy Technology Data Exchange (ETDEWEB)

Hah, Chang Joo, E-mail: changhah@kings.ac.kr [Department of NPP Engineering, KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

2015-04-29

APR 1400 is a PWR (Pressurized Water Reactor) with rated power of 3983 MWth and 241 assemblies. Recently, demand for extremely longer cycle up to 24 months is increasing with challenge of higher critical boron concentration (CBC). In this paper, assembly design method of selecting Gd-rods is introduced to reduce CBC. The purpose of the method is to lower the critical boron concentration of the preliminary core loading pattern (PLP), and consequently to achieve more negative or less positive moderator temperature coefficient (MTC). In this method, both the ratio of the number of low-Gd rod to the number of high-Gd rod (r) and assembly average Gd wt% (w) are the decision variables. The target function is the amount of soluble boron concentration reduction, which can be converted to Δk{sub TARGET}. A set of new designed fuel assembly satisfies an objective function, min [f=∑{sub i}(Δk{sub FA}−Δk{sub i})], and enables a final loading pattern to reach a target CBC. The constraints required to determine a set of Δk are physically realizable pair, (r,w), and the sum of Δk of new designed assemblies as close to Δk{sub TARGET} as possible. New Gd-bearing assemblies selected based on valid pairs of (r,w) are replaced with existing assemblies in a PLP. This design methodology is applied to Shin-Kori Unit 3 Cycle 1 used as a reference model. CASMO-3/MASTER code is used for depletion calculation. CASMO-3/MASTER calculations with new designed assemblies produce lower CBC than the expected CBC, proving that the proposed method works successful.

“Bear-ly” learning: Limits of abstraction in black bear cognition

Directory of Open Access Journals (Sweden)

Jennifer Vonk

2018-02-01

Full Text Available We presented two American black bears (Ursus americanus with a serial list learning memory task, and one of the bears with a matching-to-sample task. After extended training, both bears demonstrated some success with the memory task but failed to generalize the overarching rule of the task to novel stimuli. Matching to sample proved even more difficult for our bear to learn. We conclude that, despite previous success in training bears to respond to natural categories, quantity discriminations, and other related tasks, that bears may possess a cognitive limitation with regards to learning abstract rules. Future tests using different procedures are necessary to determine whether this is a limit of bears’ cognitive capacities, or a limitation of the current tasks as presented. Future tests should present a larger number of varying stimuli. Ideally, bears of various species should be tested on these tasks to demonstrate species as well as individual differences.

Rotatable seal assembly

International Nuclear Information System (INIS)

Garibaldi, J.L.; Logan, C.M.

1982-01-01

An assembly is provided for rotatably supporting a rotor on a stator so that vacuum chambers in the rotor and stator remain in communication while the chambers are sealed from ambient air, which enables the use of a ball bearing or the like to support most of the weight of the rotor. The apparatus includes a seal device mounted on the rotor to rotate therewith, but shiftable in position on the rotor while being sealed to the rotor as by an oring. The seal device has a flat face that is biased towards a flat face on the stator, and pressurized air is pumped between the faces to prevent contact between them while spacing them a small distance apart to avoid the inflow of large amounts of air between the faces and into the vacuum chambers

Force chains in monodisperse spherical particle assemblies: Three-dimensional measurements using neutrons

Science.gov (United States)

Wensrich, C. M.; Kisi, E. H.; Luzin, V.; Garbe, U.; Kirstein, O.; Smith, A. L.; Zhang, J. F.

2014-10-01

The full triaxial stress state within individual particles in a monodisperse spherical granular assembly has been measured. This was made possible by neutron imaging and computed tomography combined with neutron diffraction strain measurement techniques and associated stress reconstruction. The assembly in question consists of 549 precision steel ball bearings under an applied axial load of 85 MPa in a cylindrical die. Clear evidence of force chains was observed in terms of both the shape of the probability distribution function for normal stresses and the network formed by highly loaded particles. An extensive analysis of the source and magnitude of uncertainty in these measurements is also presented.

40 CFR Appendix A to Part 438 - Typical Products in Metal Products and Machinery Sectors

Science.gov (United States)

2010-07-01

... INDUSTRIAL EQUIPMENT Air & Gas Compressors Automatic Vending Machines Ball & Roller Bearings Blowers... Fields, & Services BUS & TRUCK Bus Terminal & Service Facilities Courier Services, Except by Air Freight... Work Bolts, Nuts, Screws, Rivets & Washers Crowns & Closures Cutlery Fabricated Metal Products...

Disentangling migratory routes and wintering grounds of Iberian near-threatened European Rollers Coracias garrulus.

Directory of Open Access Journals (Sweden)

Juan Rodríguez-Ruiz

Full Text Available Long-distance migrants are suffering drastic declines in the last decades. Causes beneath this problem are complex due to the wide spatial and temporal scale involved. We aim to reveal migratory routes, stopover areas, wintering grounds, and migratory strategies for the most southwestern populations of the near-threatened European Roller Coracias garrulus in order to identify conservation key areas for the non-breeding stage of this species. To this end, we used tracking data from seven satellite transmitters fitted to birds breeding in different populations throughout the Iberian Peninsula and four geolocators fitted to individuals in a southeastern Iberian population. Precise satellite data were used to describe daily activity patterns and speed in relation to the main regions crossed during the migration. Individuals from the most southwestern Iberian populations made a detour towards the Atlantic African coast whereas those from northeastern populations followed a straight north-to-south route. We identified important stopover areas in the Sahel belt, mainly in the surroundings of the Lake Chad, and wintering grounds on southwestern Africa farther west than previously reported for the species. Concerning the migratory strategy, satellite data revealed: 1 a mainly nocturnal flying activity, 2 that migration speed depended on the type of crossed habitat, with higher average speed while crossing the desert; and 3 that the migration was slower and lasted longer in autumn than in spring. The studied populations showed weak migratory connectivity, suggesting the confluence of birds from a wide range of breeding grounds in a restricted wintering area. Therefore, we suggest to target on defining precisely key areas for this species and identifying specific threats in them in order to develop an appropriate global conservation programme for the European Roller.

Characterization of spent fuel disassembly hardware and nonfuel bearing components and their relationship to 10 CFR 61

International Nuclear Information System (INIS)

Luksic, A.T.

1987-02-01

There are a variety of wastes that will be disposed of by the federal waste management system under the Nuclear Waste Policy Act of 1982. The primary waste form is spent nuclear fuel. Currently, this is in the form of fuel assemblies. If the fuel pins are removed from the fuel assembly, as in consolidation, then the fuel pins and the structural portion of the fuel assembly must be considered as separate waste streams. The structural hardware consists of end fittings, grid spacers, water rods (BWR 8 x 8 only), control rod guide tubes (PWR only) and various nuts, washers, springs, etc. These are referred to as spent fuel disassembly (SFD) hardware. There will also be a number of other components which are defined in Appendix E of 10 CFR 961, the standard utility contract. These are referred to as nonfuel-bearing (NFB) components, and include fuel channels (BWR), control rods, fission chambers, neutron sources, thimble plugs, and other components. This paper characterizes spent fuel disassembly (SFD) hardware, and nonfuel-bearing (NFB) components for the most abundant fuel types. The descriptions and figures given are representative for the items described. Many subvariants exist due to design evaluation, which are not covered. This paper also discusses the relationship of these wastes to 10 CFR 61 waste classification

Self-Assembly of Coordinative Supramolecular Polygons with Open Binding Sites.

Science.gov (United States)

Zheng, Yao-Rong; Wang, Ming; Kobayashi, Shiho; Stang, Peter J

2011-04-27

The design and synthesis of coordinative supramolecular polygons with open binding sites is described. Coordination-driven self-assembly of 2,6-bis(pyridin-4-ylethynyl)pyridine with 60° and 120° organoplatinum acceptors results in quantitative formation of a supramolecular rhomboid and hexagon, respectively, both bearing open pyridyl binding sites. The structures were determined by multinuclear ((31)P and (1)H) NMR spectroscopy and electrospray ionization (ESI) mass spectrometry, along with a computational study.

Genomic evidence of geographically widespread effect of gene flow from polar bears into brown bears.

Science.gov (United States)

Cahill, James A; Stirling, Ian; Kistler, Logan; Salamzade, Rauf; Ersmark, Erik; Fulton, Tara L; Stiller, Mathias; Green, Richard E; Shapiro, Beth

2015-03-01

Polar bears are an arctic, marine adapted species that is closely related to brown bears. Genome analyses have shown that polar bears are distinct and genetically homogeneous in comparison to brown bears. However, these analyses have also revealed a remarkable episode of polar bear gene flow into the population of brown bears that colonized the Admiralty, Baranof and Chichagof islands (ABC islands) of Alaska. Here, we present an analysis of data from a large panel of polar bear and brown bear genomes that includes brown bears from the ABC islands, the Alaskan mainland and Europe. Our results provide clear evidence that gene flow between the two species had a geographically wide impact, with polar bear DNA found within the genomes of brown bears living both on the ABC islands and in the Alaskan mainland. Intriguingly, while brown bear genomes contain up to 8.8% polar bear ancestry, polar bear genomes appear to be devoid of brown bear ancestry, suggesting the presence of a barrier to gene flow in that direction. © 2014 The Authors. Molecular Ecology Published by John Wiley & Sons Ltd.

Theoretical Simulation on the Assembly of Carbon Nanotubes Between Electrodes by AC Dielectrophoresis

Directory of Open Access Journals (Sweden)

Yang Liu

2008-01-01

Full Text Available Abstract The assembly of single-walled carbon nanotubes (SWCNTs using the AC dielectrophoresis technique is studied theoretically. It is found that the comb electrode bears better position control of SWCNTs compared to the parallel electrode. In the assembly, when some SWCNTs bridge the electrode first, they can greatly alter the local electrical field so as to “screen off” later coming SWCNTs, which contributes to the formation of dispersed SWCNT array. The screening distance scales with the gap width of electrodes and the length of SWCNTs, which provides a way to estimate the assembled density of SWCNTs. The influence of thermal noise on SWCNTs alignment is also analyzed in the simulation. It is shown that the status of the array distribution for SWCNTs is decided by the competition between the thermal noise and the AC electric-field strength. This influence of the thermal noise can be suppressed by using higher AC voltage to assemble the SWCNTs.

EFFECT OF CLEARANCE THE BALL BEARINGS ON INCORRECT WORK OF THREE-SUPORT BEARING SHAFT

Directory of Open Access Journals (Sweden)

Jarosław KACZOR

2014-06-01

Full Text Available Durability deep groove ball bearings depends on factors (called attributes design, technological and operational. Among the design features one of the most important is play in the bearings. Polish Norm shows five groups of looseness in the bearings, in which the play range from 0 to 105 microns. Manufacturers of rolling bearings they only play group, which has a bearing data, without giving the exact value of the slack. Aim of this study is to determine how it affects the play in the bearings to work three-bearing shafts, including elasticity and resilience three-bearing shafts.

Architecture, Assembly, and Emerging Applications of Branched Functional Polyelectrolytes and Poly(ionic liquid)s.

Science.gov (United States)

Xu, Weinan; Ledin, Petr A; Shevchenko, Valery V; Tsukruk, Vladimir V

2015-06-17

Branched polyelectrolytes with cylindrical brush, dendritic, hyperbranched, grafted, and star architectures bearing ionizable functional groups possess complex and unique assembly behavior in solution at surfaces and interfaces as compared to their linear counterparts. This review summarizes the recent developments in the introduction of various architectures and understanding of the assembly behavior of branched polyelectrolytes with a focus on functional polyelectrolytes and poly(ionic liquid)s with responsive properties. The branched polyelectrolytes and poly(ionic liquid)s interact electrostatically with small molecules, linear polyelectrolytes, or other branched polyelectrolytes to form assemblies of hybrid nanoparticles, multilayer thin films, responsive microcapsules, and ion-conductive membranes. The branched structures lead to unconventional assemblies and complex hierarchical structures with responsive properties as summarized in this review. Finally, we discuss prospectives for emerging applications of branched polyelectrolytes and poly(ionic liquid)s for energy harvesting and storage, controlled delivery, chemical microreactors, adaptive surfaces, and ion-exchange membranes.

The influence of API concentration on the roller compaction process: modeling and prediction of the post compacted ribbon, granule and tablet properties using multivariate data analysis.

Science.gov (United States)

Boersen, Nathan; Carvajal, M Teresa; Morris, Kenneth R; Peck, Garnet E; Pinal, Rodolfo

2015-01-01

While previous research has demonstrated roller compaction operating parameters strongly influence the properties of the final product, a greater emphasis might be placed on the raw material attributes of the formulation. There were two main objectives to this study. First, to assess the effects of different process variables on the properties of the obtained ribbons and downstream granules produced from the rolled compacted ribbons. Second, was to establish if models obtained with formulations of one active pharmaceutical ingredient (API) could predict the properties of similar formulations in terms of the excipients used, but with a different API. Tolmetin and acetaminophen, chosen for their different compaction properties, were roller compacted on Fitzpatrick roller compactor using the same formulation. Models created using tolmetin and tested using acetaminophen. The physical properties of the blends, ribbon, granule and tablet were characterized. Multivariate analysis using partial least squares was used to analyze all data. Multivariate models showed that the operating parameters and raw material attributes were essential in the prediction of ribbon porosity and post-milled particle size. The post compacted ribbon and granule attributes also significantly contributed to the prediction of the tablet tensile strength. Models derived using tolmetin could reasonably predict the ribbon porosity of a second API. After further processing, the post-milled ribbon and granules properties, rather than the physical attributes of the formulation were needed to predict downstream tablet properties. An understanding of the percolation threshold of the formulation significantly improved the predictive ability of the models.

Acute, fatal Sarcocystis calchasi-associated hepatitis in Roller pigeons (Columba livia f. dom.) at Philadelphia Zoo.

Science.gov (United States)

Trupkiewicz, J G; Calero-Bernal, R; Verma, S K; Mowery, J; Davison, S; Habecker, P; Georoff, T A; Ialeggio, D M; Dubey, J P

2016-01-30

Four Roller pigeons (Columba livia f. dom.) at the Philadelphia Zoo died suddenly. Necropsy examination revealed macroscopic hepatitis. Microscopically, the predominant lesions were in liver, characterized with necrosis and mixed cell inflammatory response. Sarcocystis calchasi-like schizonts and free merozoites were identified in liver. Transmission electron microscopy confirmed that schizonts were in hepatocytes. A few schizonts were in spleen. PCR using S. calchasi-specific primers confirmed the diagnosis. Neither lesions nor protozoa were found in brain and muscles. This is the first report of acute visceral S. calchasi-associated sarcocystosis in naturally infected avian hosts. Published by Elsevier B.V.

Structure design and simulation research of active magnetic bearing for helium centrifugal cold compressor

Science.gov (United States)

Y Zhang, S.; Pan, W.; Wei, C. B.; Wu, J. H.

2017-12-01

Helium centrifugal cold compressors are utilized to pump gaseous helium from saturated liquid helium tank to obtain super-fluid helium in cryogenic refrigeration system, which is now being developed at TIPC, CAS. Active magnetic bearing (AMB) is replacing traditional oil-fed bearing as the optimal supporting assembly for cold compressor because of its many advantages: free of contact, high rotation speed, no lubrication and so on. In this paper, five degrees of freedom for AMB are developed for the helium centrifugal cold compressor application. The structure parameters of the axial and radial magnetic bearings as well as hardware and software of the electronic control system is discussed in detail. Based on modal analysis and critical speeds calculation, a control strategy combining PID arithmetic with other phase compensators is proposed. Simulation results demonstrate that the control method not only stables AMB system but also guarantees good performance of closed-loop behaviour. The prior research work offers important base and experience for test and application of AMB experimental platform for system centrifugal cold compressor.

Geology and geomorphology of Bear Lake Valley and upper Bear River, Utah and Idaho

Science.gov (United States)

Reheis, M.C.; Laabs, B.J.C.; Kaufman, D.S.

2009-01-01

Bear Lake, on the Idaho-Utah border, lies in a fault-bounded valley through which the Bear River flows en route to the Great Salt Lake. Surficial deposits in the Bear Lake drainage basin provide a geologic context for interpretation of cores from Bear Lake deposits. In addition to groundwater discharge, Bear Lake received water and sediment from its own small drainage basin and sometimes from the Bear River and its glaciated headwaters. The lake basin interacts with the river in complex ways that are modulated by climatically induced lake-level changes, by the distribution of active Quaternary faults, and by the migration of the river across its fluvial fan north of the present lake. The upper Bear River flows northward for ???150 km from its headwaters in the northwestern Uinta Mountains, generally following the strike of regional Laramide and late Cenozoic structures. These structures likely also control the flow paths of groundwater that feeds Bear Lake, and groundwater-fed streams are the largest source of water when the lake is isolated from the Bear River. The present configuration of the Bear River with respect to Bear Lake Valley may not have been established until the late Pliocene. The absence of Uinta Range-derived quartzites in fluvial gravel on the crest of the Bear Lake Plateau east of Bear Lake suggests that the present headwaters were not part of the drainage basin in the late Tertiary. Newly mapped glacial deposits in the Bear River Range west of Bear Lake indicate several advances of valley glaciers that were probably coeval with glaciations in the Uinta Mountains. Much of the meltwater from these glaciers may have reached Bear Lake via groundwater pathways through infiltration in the karst terrain of the Bear River Range. At times during the Pleistocene, the Bear River flowed into Bear Lake and water level rose to the valley threshold at Nounan narrows. This threshold has been modified by aggradation, downcutting, and tectonics. Maximum lake

Shroud brushing device

International Nuclear Information System (INIS)

Sakamaki, Kazuo; Takabayashi, Jun-ichi.

1996-01-01

A roller screw is assembled at an axial center of the inside of a device main body. A nut is assembled to the axial center of the roller screw secured so as not to be rotated, and a base is integrally connected to the nut. An air cylinder is pivoted to the base by a pin, and an arm is disposed to a piston rod of the air cylinder. The top end of the arm is secured to a motor case, and a brush is rotated by an electric motor in the motor case. The device main body is suspended into the reactor pressure vessel of a BWR type reactor, and seated on the upper surface of a fuel support metal fitting. The roller screw is rotated to move vertically the arm by way of the nut and the base. The device main body is rotated to rotate the arm. The arm is extended and then the electric motor is driven to rotate the brush thereby polishing the inner surface of the shroud. (I.N.)

Shroud brushing device

Energy Technology Data Exchange (ETDEWEB)

Sakamaki, Kazuo; Takabayashi, Jun-ichi

1996-07-12

A roller screw is assembled at an axial center of the inside of a device main body. A nut is assembled to the axial center of the roller screw secured so as not to be rotated, and a base is integrally connected to the nut. An air cylinder is pivoted to the base by a pin, and an arm is disposed to a piston rod of the air cylinder. The top end of the arm is secured to a motor case, and a brush is rotated by an electric motor in the motor case. The device main body is suspended into the reactor pressure vessel of a BWR type reactor, and seated on the upper surface of a fuel support metal fitting. The roller screw is rotated to move vertically the arm by way of the nut and the base. The device main body is rotated to rotate the arm. The arm is extended and then the electric motor is driven to rotate the brush thereby polishing the inner surface of the shroud. (I.N.)

State Space Formulation of Nonlinear Vibration Responses Collected from a Dynamic Rotor-Bearing System: An Extension of Bearing Diagnostics to Bearing Prognostics

OpenAIRE

Peter W. Tse; Dong Wang

2017-01-01

Bearings are widely used in various industries to support rotating shafts. Their failures accelerate failures of other adjacent components and may cause unexpected machine breakdowns. In recent years, nonlinear vibration responses collected from a dynamic rotor-bearing system have been widely analyzed for bearing diagnostics. Numerous methods have been proposed to identify different bearing faults. However, these methods are unable to predict the future health conditions of bearings. To exten...

Evaluation of bearing configurations using the single bearing tester in liquid nitrogen

Science.gov (United States)

Jett, T.; Hall, P.; Thom, R.

1991-01-01

Various bearing configurations were tested using the Marshall Space Flight Center single bearing tester with LN2 as the cryogenic coolant. The baseline was one Rocketdyne phase one high pressure oxidizer turbopump (HPOTP) pump end 45-mm bore bearing. The bearing configurations that were tested included a Salox/M cage configuration, a silicon nitride ball configuration, an elongated cage configuration, and a Bray 601 grease configuration.

Improvement of journal bearing operation at heavy misalignment using bearing flexibility and compliant liners

DEFF Research Database (Denmark)

Thomsen, Kim; Klit, Peder

2012-01-01

A flexure journal bearing design is proposed that will improve operational behaviour of a journal bearing at pronounced misalignment. Using a thermoelastohydrodynamic model, it is shown that the proposed flexure journal bearing has vastly increased the hydrodynamic performance compared to the stiff...... bearing when misaligned. The hydrodynamic performance is evaluated on lubricant film thickness, pressure and temperature. Furthermore, the influence of a compliant bearing liner is investigated and it is found that it increases the hydrodynamic performance when applied to a stiff bearing, whereas...... the liner has practically no influence on the flexure journal bearing's performance....

A comparative study of physical and chemical properties of different pozzolanic materials used for roller compacted concrete RCC dams

OpenAIRE

Husein Malkawi Abdallah I.; Shatnawi Ehab; Husein Malkawi Dima A.

2017-01-01

This paper addresses the feasibility and the efficiency of using Natural Pozzolan and/or Rock flour in Roller Compacted Concrete (RCC) gravity dams. For this purpose, five identical mortar trial mixes were prepared using five different supplementary materials, i.e., fly ash produced in South Africa (proven to be effective in RCC construction), fly ash produced in Turkey, Jordanian natural pozzolan, Saudi natural pozzolan, and rock flour from Mujib Dam basalt quarry. The physical and chemical ...

Nuclear genomic sequences reveal that polar bears are an old and distinct bear lineage.

Science.gov (United States)

Hailer, Frank; Kutschera, Verena E; Hallström, Björn M; Klassert, Denise; Fain, Steven R; Leonard, Jennifer A; Arnason, Ulfur; Janke, Axel

2012-04-20

Recent studies have shown that the polar bear matriline (mitochondrial DNA) evolved from a brown bear lineage since the late Pleistocene, potentially indicating rapid speciation and adaption to arctic conditions. Here, we present a high-resolution data set from multiple independent loci across the nuclear genomes of a broad sample of polar, brown, and black bears. Bayesian coalescent analyses place polar bears outside the brown bear clade and date the divergence much earlier, in the middle Pleistocene, about 600 (338 to 934) thousand years ago. This provides more time for polar bear evolution and confirms previous suggestions that polar bears carry introgressed brown bear mitochondrial DNA due to past hybridization. Our results highlight that multilocus genomic analyses are crucial for an accurate understanding of evolutionary history.

Report on achievements in fiscal 1979 in Sunshine Project. Development of a high-temperature ground layer drilling technology (feasibility study on high-temperature ground layer drilling); 1979 nendo koon chiso kussaku gijutsu no kaihatsu seika hokokusho. Koon chiso kussaku ni kansuru feasibility study

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

This paper reports research achievements on the following items: (1) a roller cutter bit, (2) solid bit and air friction bit, and (3) bit materials. In Item 1, fabrication and test were performed on a roller cutter bit on which studies were made for use, heat treatment, and manufacturing method of improved heat resistant steels. Effects were obtained in tip retention force when high-temperature rocks are drilled. Research and development was made on construction of a bearing as a friction type bit, in which dry bearing pressed in with a solid lubricating agent was inserted into an outer race. In Item 2, an indoor drilling test was carried out on a solid bit using two-layered ultra hard tip. A durability test on an air friction bit bearing recognized no wear on a check after operation of about 40 hours under a load of 3 tons and at a rotation speed of 80 rpm. Thus, the bearing was considered sufficiently reliable from the aspect of durability. In mud water drilling in the field, some wear was observed in the thrust direction. In Item 3, studies were performed on heat and corrosion resistant tip materials, bit materials using heat resistant alloys, improvement in bearing materials, strengthening of inside of a cutter made of metallurgically sintered powder, provision of heat resistance onto bit materials, indoor cutting tests, and seals for bits. (NEDO)

Analysis of the Journal Bearing Friction Losses in a Heavy-Duty Diesel Engine

Directory of Open Access Journals (Sweden)

Christoph Knauder

2015-04-01

Full Text Available Internal combustion engines (ICE for the use in heavy-duty trucks and buses have to fulfil demanding requirements for both vehicle efficiency as well as for emission of greenhouse gases. Beside the piston assembly the journal bearings are among the largest contributors to friction in the ICE. Through a combination of measurements and validated simulation methods the journal bearing friction losses of a state-of-the-art heavy-duty Diesel engine are investigated for a large range of real world operating conditions. To this task recently developed and extensively validated simulation methods are used together with realistic lubricant models that consider the Non-Newtonian behaviour as well as the piezoviscous effect. In addition, the potential for further friction reduction with the use of ultra-low viscosity lubricants is explored. The results reveal a potential of about 8% friction reduction in the journal bearings using a 0W20 ultra-low viscosity oil with an HTHS-viscosity (The HTHS-viscosity is defined as the dynamic viscosity of the lubricant measured at 150 °C and at a shear rate of 106 s

Vibration model of rolling element bearings in a rotor-bearing system for fault diagnosis

Science.gov (United States)

Cong, Feiyun; Chen, Jin; Dong, Guangming; Pecht, Michael

2013-04-01

Rolling element bearing faults are among the main causes of breakdown in rotating machines. In this paper, a rolling bearing fault model is proposed based on the dynamic load analysis of a rotor-bearing system. The rotor impact factor is taken into consideration in the rolling bearing fault signal model. The defect load on the surface of the bearing is divided into two parts, the alternate load and the determinate load. The vibration response of the proposed fault signal model is investigated and the fault signal calculating equation is derived through dynamic and kinematic analysis. Outer race and inner race fault simulations are realized in the paper. The simulation process includes consideration of several parameters, such as the gravity of the rotor-bearing system, the imbalance of the rotor, and the location of the defect on the surface. The simulation results show that different amplitude contributions of the alternate load and determinate load will cause different envelope spectrum expressions. The rotating frequency sidebands will occur in the envelope spectrum in addition to the fault characteristic frequency. This appearance of sidebands will increase the difficulty of fault recognition in intelligent fault diagnosis. The experiments given in the paper have successfully verified the proposed signal model simulation results. The test rig design of the rotor bearing system simulated several operating conditions: (1) rotor bearing only; (2) rotor bearing with loader added; (3) rotor bearing with loader and rotor disk; and (4) bearing fault simulation without rotor influence. The results of the experiments have verified that the proposed rolling bearing signal model is important to the rolling bearing fault diagnosis of rotor-bearing systems.

Polar bears at risk

Energy Technology Data Exchange (ETDEWEB)

Norris, S.; Rosentrater, L.; Eid, P.M. [WWF International Arctic Programme, Oslo (Norway)

2002-05-01

Polar bears, the world's largest terrestrial carnivore, spend much of their lives on the arctic sea ice. This is where they hunt and move between feeding, denning, and resting areas. The world population, estimated at 22,000 bears, is made up of 20 relatively distinct populations varying in size from a few hundred to a few thousand animals. About 60 per cent of all polar bears are found in Canada. In general, the status of this species is stable, although there are pronounced differences between populations. Reductions in the extent and thickness of sea ice has lead the IUCN Polar Bear Specialist Group to describe climate change as one of the major threats facing polar bears today. Though the long-term effects of climate change will vary in different areas of the Arctic, impacts on the condition and reproductive success of polar bears and their prey are likely to be negative. Longer ice-free periods resulting from earlier break-up of sea ice in the spring and later formation in the fall is already impacting polar bears in the southern portions of their range. In Canada's Hudson Bay, for example, bears hunt on the ice through the winter and into early summer, after which the ice melts completely, forcing bears ashore to fast on stored fat until freeze-up in the fall. The time bears have on the ice to hunt and build up their body condition is cut short when the ice melts early. Studies from Hudson Bay show that for every week earlier that ice break-up occurs, bears will come ashore 10 kg lighter and in poorer condition. It is likely that populations of polar bears dividing their time between land and sea will be severely reduced and local extinctions may occur as greenhouse gas emissions continue to rise and sea ice melts. Expected changes in regional weather patterns will also impact polar bears. Rain in the late winter can cause maternity dens to collapse before females and cubs have departed, thus exposing occupants to the elements and to predators. Such

Local Attitudes towards Bear Management after Illegal Feeding and Problem Bear Activity.

Science.gov (United States)

Dubois, Sara; Fraser, David

2013-09-12

The "pot bears" received international media attention in 2010 after police discovered the intentional feeding of over 20 black bears during the investigation of an alleged marijuana-growing operation in Christina Lake, British Columbia, Canada. A two-phase random digit dialing survey of the community was conducted in 2011 to understand local perspectives on bear policy and management, before and after a summer of problem bear activity and government interventions. Of the 159 households surveyed in February 2011, most had neutral or positive attitudes towards bears in general, and supported the initial decision to feed the food-conditioned bears until the autumn hibernation. In contrast to wildlife experts however, most participants supported relocating the problem bears, or allowing them to remain in the area, ahead of killing; in part this arose from notions of fairness despite the acknowledged problems of relocation. Most locals were aware of the years of feeding but did not report it, evidently failing to see it as a serious form of harm, even after many bears had been killed. This underscores the importance of preventive action on wildlife feeding and the need to narrow the gap between public and expert opinion on the likely effects of relocation versus killing.

Three-dimensional earthquake analysis of roller-compacted concrete dams

Directory of Open Access Journals (Sweden)

M. E. Kartal

2012-07-01

Full Text Available Ground motion effect on a roller-compacted concrete (RCC dams in the earthquake zone should be taken into account for the most critical conditions. This study presents three-dimensional earthquake response of a RCC dam considering geometrical non-linearity. Besides, material and connection non-linearity are also taken into consideration in the time-history analyses. Bilinear and multilinear kinematic hardening material models are utilized in the materially non-linear analyses for concrete and foundation rock respectively. The contraction joints inside the dam blocks and dam–foundation–reservoir interaction are modeled by the contact elements. The hydrostatic and hydrodynamic pressures of the reservoir water are modeled with the fluid finite elements based on the Lagrangian approach. The gravity and hydrostatic pressure effects are employed as initial condition before the strong ground motion. In the earthquake analyses, viscous dampers are defined in the finite element model to represent infinite boundary conditions. According to numerical solutions, horizontal displacements increase under hydrodynamic pressure. Besides, those also increase in the materially non-linear analyses of the dam. In addition, while the principle stress components by the hydrodynamic pressure effect the reservoir water, those decrease in the materially non-linear time-history analyses.

Genetic relationships of extant brown bears (Ursus arctos) and polar bears (Ursus maritimus).

Science.gov (United States)

Cronin, Matthew A; MacNeil, Michael D

2012-01-01

Polar bears (Ursus maritimus) and brown bears (Ursus arctos) are closely related species for which extensive mitochondrial and nuclear phylogenetic comparisons have been made. We used previously published genotype data for 8 microsatellite DNA loci from 930 brown bears in 19 populations and 473 polar bears in 16 populations to compare the population genetic relationships of extant populations of the species. Genetic distances (Nei standard distance = 1.157), the proportion of private alleles (52% of alleles are not shared by the species), and Bayesian cluster analysis are consistent with morphological and life-history characteristics that distinguish polar bears and brown bears as different species with little or no gene flow among extant populations.

An Evaluation of the 64-meter Antenna Radial Bearing for Use on the 70-meter Antenna

Science.gov (United States)

Mcginness, H. D.

1985-01-01

The derivation of the proper truck preload is discussed and is shown to be dependent upon the azimuth drive preload direction, the wind direction and magnitude, and the out of roundness of the track. The resulting wheel and track contact stresses were evaluated and found to be satisfactory for either the 64-m or 70-m antenna. The wheel bearing loads were found to be quite satisfactory for the larger 70-m antenna. Methods for evaluating the effects of track out of roundness and for aligning the wheel and truck assemblies are presented. It is believed that these methods are practical and that the increased loadings on the parts should not affect the expected long life of the azimuth bearing.

Application of hydraulically assembled shaft coupling hubs to large agitators

International Nuclear Information System (INIS)

Murray, W.E.; Anderson, T.D.; Bethmann, H.K.

1991-01-01

This paper describes the basis for and implementation of hydraulically assembled shaft coupling hubs for large tank-mounted agitators. This modification to the original design was intended to minimize maintenance personnel exposure to ionizing radiation and also provide for disassembly capability without damage to shafts or hubs. In addition to realizing these objectives, test confirmed that the modified couplings reduced agitator shaft end runouts approximately 65%, thereby reducing bearing loads and increasing service life, a significant enhancement for a nuclear facility. 5 refs

Removable fuel assembly for nuclear reactor

International Nuclear Information System (INIS)

Dubief, J.M.; Bonnamour, M.

1984-01-01

To facilitate the replacement of one or more fuel rods, taking into account the fact the operations are remote operations and under several meters of water, the following invention is presented. The fuel assembly is composed of a bundle of canned fuel pencils maintened on a structure which includes ends linked by spacer tubes. These tubes are fixed to one end in such a manner they are removable. For this, the plug of each tube has a plane stop surface on the end part and a conic coupling and guiding plug cooperating with a truncated bearing of the end part. Flat parts made on the cone allow to stop the tube rotating [fr

EFFECT OF BEARING MACROGEOMETRY ON BEARING PERFORMANCE IN ELASTOHYDRODYNAMIC LUBRICATION

Directory of Open Access Journals (Sweden)

Emin GÜLLÜ

2000-01-01

Full Text Available During manufacturing, ideal dimension and mutual positioning of machine elements proposed in project desing can be achieved only within certain range of tolerances. These tolerances, being classified in two groups, related to micro and macro geometry of machine elements, don't have to effect the functioning of these elements. So, as for all machine elements, investigation of the effects of macro and micro tolerances for journal bearings is important. In this study, we have investigated the effect of macro geometric irregularities of journal bearings on performance characteristics. In this regard, we have studied the change of bearing performance in respect to deviation from ideal circle for an elliptic shaft with small ovality rolling in circular journal bearing.

The influence of incline and speed on work rate, gross efficiency and kinematics of roller ski skating.

Science.gov (United States)

Sandbakk, Øyvind; Ettema, Gertjan; Holmberg, Hans-Christer

2012-08-01

During competitions, elite cross-country skiers produce higher external work rates on uphill than on flat terrain. However, it is not presently known whether this reflects solely higher energy expenditure. Furthermore, the kinematic factors associated with these higher rates of uphill work have not yet been examined. Therefore, in the present investigation the work rate and associated kinematic parameters at similar metabolic rates during roller ski skating on flat and uphill terrains have been compared. Seven elite male skiers performed six 5-min sub-maximal exercise bouts at the same low, moderate and high metabolic rates on 2 and 8% inclines, while roller skiing on a treadmill employing the G3 skating technique. The work rate was calculated as work against gravity and friction, whereas the energetic equivalent of VO(2) was taken as the metabolic rate. Gross efficiency was defined as work rate divided by metabolic rate. Kinematic parameters were analyzed in three dimensions. At the same metabolic rate, the work rate, cycle rate, work per cycle and relative duration of propulsive phases during a cycle of movement were all higher on the 8% than on the 2% incline at all speeds (all P < 0.05). At similar work rates, gross efficiency was greater on the 8% incline (P < 0.05). In conclusion, these elite skiers consistently demonstrated higher work rates on the 8% incline. To achieve the higher work rates on the steeper incline, these elite skiers employed higher cycle rates and performed more work per cycle, in association with a longer relative propulsive phase.

Positioning drive for absorber rods of a nuclear reactor

International Nuclear Information System (INIS)

Acher, H.

1977-01-01

The invention concerns a positioning drive for absorber rods of a nuclear reactor, of a threaded spindle and traveling nut type. In this positioning drive, rollers are provided the nut, which engage with the threads of the spindle and have an axis extending essentially at right angles to the longitudinal axis of the spindle. Three of the rollers are preferably combined in a traveling-nut housing, by means of anti-friction bearing elements. The positioning speed of such mechanical spindle drives can be increased thereby substantially. The invention is of interest particularly for boiling-water reactors. 9 claims, 8 figures

Studies of The Durability of Belt Conveyor Idlers with Working Loads Taken into Account

Science.gov (United States)

Król, Robert

2017-12-01

The results of laboratory and operational studies conducted in the Machinery Systems Division of Wroclaw University of Technology in recent years have became the basis for selecting proper belt conveyor roller designs optimized for specific strength and operational criteria. The usefulness of the results for assessing the energy intensity of idlers, estimating their durability and determining modernization policies has been confirmed. Methods of estimating the durability of carrying idlers on the basis of the identified output stream distributions are presented. Results of studies carried out using an analytical method and a laboratory method are reported. It has been shown that the operational durability of a roller is determined by its design, the roller set parameters (the spacing and the angle of bevel) and the operating conditions having a bearing on the irregularity of the transported output stream.

Passive magnetic bearing configurations

Science.gov (United States)

Post, Richard F [Walnut Creek, CA

2011-01-25

A journal bearing provides vertical and radial stability to a rotor of a passive magnetic bearing system when the rotor is not rotating and when it is rotating. In the passive magnetic bearing system, the rotor has a vertical axis of rotation. Without the journal bearing, the rotor is vertically and radially unstable when stationary, and is vertically stable and radially unstable when rotating.

Improving Performance of Cantilevered Momentum Wheel Assemblies by Soft Suspension Support

OpenAIRE

Zhou, Weiyong; Li, Dongxu

2013-01-01

This paper focuses on improving the performance of the rigid support cantilevered momentum wheel assemblies (CMWA) by soft suspension support. A CMWA, supported by two angular contact ball bearings, was modeled as a Jeffcott rotor. The support stiffness, before and after in series with a linear soft suspension support, were simplified as two Duffing's type springs respectively. The result shows that the rigid support CMWA produces large disturbance force at the resonance speed range. The soft...

Comparison of fixed-bearing and mobile-bearing total knee arthroplasty after high tibial osteotomy.

Science.gov (United States)

Hernigou, Philippe; Huys, Maxime; Pariat, Jacques; Roubineau, François; Flouzat Lachaniette, Charles Henri; Dubory, Arnaud

2018-02-01

There is no information comparing the results of fixed-bearing total knee replacement and mobile-bearing total knee replacement in the same patients previously treated by high tibial osteotomy. The purpose was therefore to compare fixed-bearing and mobile-bearing total knee replacements in patients treated with previous high tibial osteotomy. We compared the results of 57 patients with osteoarthritis who had received a fixed-bearing prosthesis after high tibial osteotomy with the results of 41 matched patients who had received a rotating platform after high tibial osteotomy. The match was made for length of follow-up period. The mean follow-up was 17 years (range, 15-20 years). The patients were assessed clinically and radiographically. The pre-operative knee scores had no statistically significant differences between the two groups. So was the case with the intra-operative releases, blood loss, thromboembolic complications and infection rates in either group. There was significant improvement in both groups of knees, and no significant difference was observed between the groups (i.e., fixed-bearing and mobile-bearing knees) for the mean Knee Society knee clinical score (95 and 92 points, respectively), or the Knee Society knee functional score (82 and 83 points, respectively) at the latest follow-up. However, the mean post-operative knee motion was higher for the fixed-bearing group (117° versus 110°). In the fixed-bearing group, one knee was revised because of periprosthetic fracture. In the rotating platform mobile-bearing group, one knee was revised because of aseptic loosening of the tibial component. The Kaplan-Meier survivorship for revision at ten years of follow-up was 95.2% for the fixed bearing prosthesis and 91.1% for the rotating platform mobile-bearing prosthesis. Although we did manage to detect significant differences mainly in clinical and radiographic results between the two groups, we found no superiority or inferiority of the mobile-bearing

Genomic evidence of geographically widespread effect of gene flow from polar bears into brown bears

OpenAIRE

Cahill, James A; Stirling, Ian; Kistler, Logan; Salamzade, Rauf; Ersmark, Erik; Fulton, Tara L; Stiller, Mathias; Green, Richard E; Shapiro, Beth

2015-01-01

© 2014 The Authors. Molecular Ecology Published by John Wiley & Sons Ltd. Polar bears are an arctic, marine adapted species that is closely related to brown bears. Genome analyses have shown that polar bears are distinct and genetically homogeneous in comparison to brown bears. However, these analyses have also revealed a remarkable episode of polar bear gene flow into the population of brown bears that colonized the Admiralty, Baranof and Chichagof islands (ABC islands) of Alaska. Here, we...

The role of human outdoor recreation in shaping patterns of grizzly bear-black bear co-occurrence.

Directory of Open Access Journals (Sweden)

Andrew Ladle

Full Text Available Species' distributions are influenced by a combination of landscape variables and biotic interactions with other species, including people. Grizzly bears and black bears are sympatric, competing omnivores that also share habitats with human recreationists. By adapting models for multi-species occupancy analysis, we analyzed trail camera data from 192 trail camera locations in and around Jasper National Park, Canada to estimate grizzly bear and black bear occurrence and intensity of trail use. We documented (a occurrence of grizzly bears and black bears relative to habitat variables (b occurrence and intensity of use relative to competing bear species and motorised and non-motorised recreational activity, and (c temporal overlap in activity patterns among the two bear species and recreationists. Grizzly bears were spatially separated from black bears, selecting higher elevations and locations farther from roads. Both species co-occurred with motorised and non-motorised recreation, however, grizzly bears reduced their intensity of use of sites with motorised recreation present. Black bears showed higher temporal activity overlap with recreational activity than grizzly bears, however differences in bear daily activity patterns between sites with and without motorised and non-motorised recreation were not significant. Reduced intensity of use by grizzly bears of sites where motorised recreation was present is a concern given off-road recreation is becoming increasingly popular in North America, and can negatively influence grizzly bear recovery by reducing foraging opportunities near or on trails. Camera traps and multi-species occurrence models offer non-invasive methods for identifying how habitat use by animals changes relative to sympatric species, including humans. These conclusions emphasise the need for integrated land-use planning, access management, and grizzly bear conservation efforts to consider the implications of continued access for

The role of human outdoor recreation in shaping patterns of grizzly bear-black bear co-occurrence.

Science.gov (United States)

Ladle, Andrew; Steenweg, Robin; Shepherd, Brenda; Boyce, Mark S

2018-01-01

Species' distributions are influenced by a combination of landscape variables and biotic interactions with other species, including people. Grizzly bears and black bears are sympatric, competing omnivores that also share habitats with human recreationists. By adapting models for multi-species occupancy analysis, we analyzed trail camera data from 192 trail camera locations in and around Jasper National Park, Canada to estimate grizzly bear and black bear occurrence and intensity of trail use. We documented (a) occurrence of grizzly bears and black bears relative to habitat variables (b) occurrence and intensity of use relative to competing bear species and motorised and non-motorised recreational activity, and (c) temporal overlap in activity patterns among the two bear species and recreationists. Grizzly bears were spatially separated from black bears, selecting higher elevations and locations farther from roads. Both species co-occurred with motorised and non-motorised recreation, however, grizzly bears reduced their intensity of use of sites with motorised recreation present. Black bears showed higher temporal activity overlap with recreational activity than grizzly bears, however differences in bear daily activity patterns between sites with and without motorised and non-motorised recreation were not significant. Reduced intensity of use by grizzly bears of sites where motorised recreation was present is a concern given off-road recreation is becoming increasingly popular in North America, and can negatively influence grizzly bear recovery by reducing foraging opportunities near or on trails. Camera traps and multi-species occurrence models offer non-invasive methods for identifying how habitat use by animals changes relative to sympatric species, including humans. These conclusions emphasise the need for integrated land-use planning, access management, and grizzly bear conservation efforts to consider the implications of continued access for motorised

Unbalance Response Prediction for Rotors on Ball Bearings Using Speed and Load Dependent Nonlinear Bearing Stiffness

Science.gov (United States)

Fleming, David P.; Poplawski, J. V.

2003-01-01

Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. For this work bearing forces were calculated by COBRA-AHS, a recently developed rolling-element bearing analysis code. Bearing stiffness was found to be a strong function of bearing deflection, with higher deflection producing markedly higher stiffness. Curves fitted to the bearing data for a range of speeds and loads were supplied to a flexible rotor unbalance response analysis. The rotordynamic analysis showed that vibration response varied nonlinearly with the amount of rotor imbalance. Moreover, the increase in stiffness as critical speeds were approached caused a large increase in rotor and bearing vibration amplitude over part of the speed range compared to the case of constant bearing stiffness. Regions of bistable operation were possible, in which the amplitude at a given speed was much larger during rotor acceleration than during deceleration. A moderate amount of damping will eliminate the bistable region, but this damping is not inherent in ball bearings.

Experimental Research on the Impact of Thin-Wall Ratio and the Fillet Radius of Forming Roller on the Limiting Spinning Ratio of AMS 5504 Sheets

Directory of Open Access Journals (Sweden)

Kut S.

2017-12-01

Full Text Available Results of experimental investigations of metal spinning process of AMS 5504 sheets. cylindrical drawpieces with use of discs-shaped sheet with various diameter and thickness were shown in this work. Tests were performed on two roller metal spinning machine of a vertical axis Leifeld SFC 800 V500.

A G-function-based reliability-based design methodology applied to a cam roller system

International Nuclear Information System (INIS)

Wang, W.; Sui, P.; Wu, Y.T.

1996-01-01

Conventional reliability-based design optimization methods treats the reliability function as an ordinary function and applies existing mathematical programming techniques to solve the design problem. As a result, the conventional approach requires nested loops with respect to g-function, and is very time consuming. A new reliability-based design method is proposed in this paper that deals with the g-function directly instead of the reliability function. This approach has the potential of significantly reducing the number of calls for g-function calculations since it requires only one full reliability analysis in a design iteration. A cam roller system in a typical high pressure fuel injection diesel engine is designed using both the proposed and the conventional approach. The proposed method is much more efficient for this application

Local Attitudes towards Bear Management after Illegal Feeding and Problem Bear Activity

Directory of Open Access Journals (Sweden)

David Fraser

2013-09-01

Full Text Available The “pot bears” received international media attention in 2010 after police discovered the intentional feeding of over 20 black bears during the investigation of an alleged marijuana-growing operation in Christina Lake, British Columbia, Canada. A two-phase random digit dialing survey of the community was conducted in 2011 to understand local perspectives on bear policy and management, before and after a summer of problem bear activity and government interventions. Of the 159 households surveyed in February 2011, most had neutral or positive attitudes towards bears in general, and supported the initial decision to feed the food-conditioned bears until the autumn hibernation. In contrast to wildlife experts however, most participants supported relocating the problem bears, or allowing them to remain in the area, ahead of killing; in part this arose from notions of fairness despite the acknowledged problems of relocation. Most locals were aware of the years of feeding but did not report it, evidently failing to see it as a serious form of harm, even after many bears had been killed. This underscores the importance of preventive action on wildlife feeding and the need to narrow the gap between public and expert opinion on the likely effects of relocation versus killing.

A semi-analytical bearing model considering outer race flexibility for model based bearing load monitoring

Science.gov (United States)

Kerst, Stijn; Shyrokau, Barys; Holweg, Edward

2018-05-01

This paper proposes a novel semi-analytical bearing model addressing flexibility of the bearing outer race structure. It furthermore presents the application of this model in a bearing load condition monitoring approach. The bearing model is developed as current computational low cost bearing models fail to provide an accurate description of the more and more common flexible size and weight optimized bearing designs due to their assumptions of rigidity. In the proposed bearing model raceway flexibility is described by the use of static deformation shapes. The excitation of the deformation shapes is calculated based on the modelled rolling element loads and a Fourier series based compliance approximation. The resulting model is computational low cost and provides an accurate description of the rolling element loads for flexible outer raceway structures. The latter is validated by a simulation-based comparison study with a well-established bearing simulation software tool. An experimental study finally shows the potential of the proposed model in a bearing load monitoring approach.

EFFECT OF CLEARANCE THE BALL BEARINGS ON INCORRECT WORK OF THREE-SUPORT BEARING SHAFT