Modelling cooperation of industrial robots as multi-agent systems

Science.gov (United States)

Hryniewicz, P.; Banas, W.; Foit, K.; Gwiazda, A.; Sekala, A.

2017-08-01

Nowadays, more and more often in a cell is more than one robot, there is also a dual arm robots, because of this cooperation of two robots in the same space becomes more and more important. Programming robotic cell consisting of two or more robots are currently performed separately for each element of the robot and the cell. It is performed only synchronization programs, but no robot movements. In such situations often placed industrial robots so they do not have common space so the robots are operated separately. When industrial robots are a common space this space can occupy only one robot the other one must be outside the common space. It is very difficult to find applications where two robots are in the same workspace. It was tested but one robot did not do of movement when moving the second and waited for permission to move from the second when it sent a permit - stop the move. Such programs are very difficult and require a lot of experience from the programmer and must be tested separately at the beginning and then very slowly under control. Ideally, the operator takes care of exactly one robot during the test and it is very important to take special care.

Dynamical Intention: Integrated Intelligence Modeling for Goal-directed Embodied Agents

Directory of Open Access Journals (Sweden)

Eric Aaron

2016-11-01

Full Text Available Intelligent embodied robots are integrated systems: As they move continuously through their environments, executing behaviors and carrying out tasks, components for low-level and high-level intelligence are integrated in the robot's cognitive system, and cognitive and physical processes combine to create their behavior. For a modeling framework to enable the design and analysis of such integrated intelligence, the underlying representations in the design of the robot should be dynamically sensitive, capable of reflecting both continuous motion and micro-cognitive influences, while also directly representing the necessary beliefs and intentions for goal-directed behavior. In this paper, a dynamical intention-based modeling framework is presented that satisfies these criteria, along with a hybrid dynamical cognitive agent (HDCA framework for employing dynamical intentions in embodied agents. This dynamical intention-HDCA (DI-HDCA modeling framework is a fusion of concepts from spreading activation networks, hybrid dynamical system models, and the BDI (belief-desire-intention theory of goal-directed reasoning, adapted and employed unconventionally to meet entailments of environment and embodiment. The paper presents two kinds of autonomous agent learning results that demonstrate dynamical intentions and the multi-faceted integration they enable in embodied robots: with a simulated service robot in a grid-world office environment, reactive-level learning minimizes reliance on deliberative-level intelligence, enabling task sequencing and action selection to be distributed over both deliberative and reactive levels; and with a simulated game of Tag, the cognitive-physical integration of an autonomous agent enables the straightforward learning of a user-specified strategy during gameplay, without interruption to the game. In addition, the paper argues that dynamical intentions are consistent with cognitive theory underlying goal-directed behavior, and

Multi-agent robotic systems and applications for satellite missions

Science.gov (United States)

Nunes, Miguel A.

A revolution in the space sector is happening. It is expected that in the next decade there will be more satellites launched than in the previous sixty years of space exploration. Major challenges are associated with this growth of space assets such as the autonomy and management of large groups of satellites, in particular with small satellites. There are two main objectives for this work. First, a flexible and distributed software architecture is presented to expand the possibilities of spacecraft autonomy and in particular autonomous motion in attitude and position. The approach taken is based on the concept of distributed software agents, also referred to as multi-agent robotic system. Agents are defined as software programs that are social, reactive and proactive to autonomously maximize the chances of achieving the set goals. Part of the work is to demonstrate that a multi-agent robotic system is a feasible approach for different problems of autonomy such as satellite attitude determination and control and autonomous rendezvous and docking. The second main objective is to develop a method to optimize multi-satellite configurations in space, also known as satellite constellations. This automated method generates new optimal mega-constellations designs for Earth observations and fast revisit times on large ground areas. The optimal satellite constellation can be used by researchers as the baseline for new missions. The first contribution of this work is the development of a new multi-agent robotic system for distributing the attitude determination and control subsystem for HiakaSat. The multi-agent robotic system is implemented and tested on the satellite hardware-in-the-loop testbed that simulates a representative space environment. The results show that the newly proposed system for this particular case achieves an equivalent control performance when compared to the monolithic implementation. In terms on computational efficiency it is found that the multi-agent

Human-Robot Teaming in a Multi-Agent Space Assembly Task

Science.gov (United States)

Rehnmark, Fredrik; Currie, Nancy; Ambrose, Robert O.; Culbert, Christopher

2004-01-01

NASA's Human Space Flight program depends heavily on spacewalks performed by pairs of suited human astronauts. These Extra-Vehicular Activities (EVAs) are severely restricted in both duration and scope by consumables and available manpower. An expanded multi-agent EVA team combining the information-gathering and problem-solving skills of humans with the survivability and physical capabilities of robots is proposed and illustrated by example. Such teams are useful for large-scale, complex missions requiring dispersed manipulation, locomotion and sensing capabilities. To study collaboration modalities within a multi-agent EVA team, a 1-g test is conducted with humans and robots working together in various supporting roles.

Study and Application of Reinforcement Learning in Cooperative Strategy of the Robot Soccer Based on BDI Model

Directory of Open Access Journals (Sweden)

Wu Bo-ying

2009-11-01

Full Text Available The dynamic cooperation model of multi-Agent is formed by combining reinforcement learning with BDI model. In this model, the concept of the individual optimization loses its meaning, because the repayment of each Agent dose not only depend on itsself but also on the choice of other Agents. All Agents can pursue a common optimum solution and try to realize the united intention as a whole to a maximum limit. The robot moves to its goal, depending on the present positions of the other robots that cooperate with it and the present position of the ball. One of these robots cooperating with it is controlled to move by man with a joystick. In this way, Agent can be ensured to search for each state-action as frequently as possible when it carries on choosing movements, so as to shorten the time of searching for the movement space so that the convergence speed of reinforcement learning can be improved. The validity of the proposed cooperative strategy for the robot soccer has been proved by combining theoretical analysis with simulation robot soccer match (11vs11 .

Proposed Methodology for Application of Human-like gradual Multi-Agent Q-Learning (HuMAQ) for Multi-robot Exploration

International Nuclear Information System (INIS)

Ray, Dip Narayan; Majumder, Somajyoti

2014-01-01

Several attempts have been made by the researchers around the world to develop a number of autonomous exploration techniques for robots. But it has been always an important issue for developing the algorithm for unstructured and unknown environments. Human-like gradual Multi-agent Q-leaming (HuMAQ) is a technique developed for autonomous robotic exploration in unknown (and even unimaginable) environments. It has been successfully implemented in multi-agent single robotic system. HuMAQ uses the concept of Subsumption architecture, a well-known Behaviour-based architecture for prioritizing the agents of the multi-agent system and executes only the most common action out of all the different actions recommended by different agents. Instead of using new state-action table (Q-table) each time, HuMAQ uses the immediate past table for efficient and faster exploration. The proof of learning has also been established both theoretically and practically. HuMAQ has the potential to be used in different and difficult situations as well as applications. The same architecture has been modified to use for multi-robot exploration in an environment. Apart from all other existing agents used in the single robotic system, agents for inter-robot communication and coordination/ co-operation with the other similar robots have been introduced in the present research. Current work uses a series of indigenously developed identical autonomous robotic systems, communicating with each other through ZigBee protocol

Modelling of industrial robot in LabView Robotics

Science.gov (United States)

Banas, W.; Cwikła, G.; Foit, K.; Gwiazda, A.; Monica, Z.; Sekala, A.

2017-08-01

Currently can find many models of industrial systems including robots. These models differ from each other not only by the accuracy representation parameters, but the representation range. For example, CAD models describe the geometry of the robot and some even designate a mass parameters as mass, center of gravity, moment of inertia, etc. These models are used in the design of robotic lines and sockets. Also systems for off-line programming use these models and many of them can be exported to CAD. It is important to note that models for off-line programming describe not only the geometry but contain the information necessary to create a program for the robot. Exports from CAD to off-line programming system requires additional information. These models are used for static determination of reachability points, and testing collision. It’s enough to generate a program for the robot, and even check the interaction of elements of the production line, or robotic cell. Mathematical models allow robots to study the properties of kinematic and dynamic of robot movement. In these models the geometry is not so important, so are used only selected parameters such as the length of the robot arm, the center of gravity, moment of inertia. These parameters are introduced into the equations of motion of the robot and motion parameters are determined.

Formalization, implementation, and modeling of institutional controllers for distributed robotic systems.

Science.gov (United States)

Pereira, José N; Silva, Porfírio; Lima, Pedro U; Martinoli, Alcherio

2014-01-01

The work described is part of a long term program of introducing institutional robotics, a novel framework for the coordination of robot teams that stems from institutional economics concepts. Under the framework, institutions are cumulative sets of persistent artificial modifications made to the environment or to the internal mechanisms of a subset of agents, thought to be functional for the collective order. In this article we introduce a formal model of institutional controllers based on Petri nets. We define executable Petri nets-an extension of Petri nets that takes into account robot actions and sensing-to design, program, and execute institutional controllers. We use a generalized stochastic Petri net view of the robot team controlled by the institutional controllers to model and analyze the stochastic performance of the resulting distributed robotic system. The ability of our formalism to replicate results obtained using other approaches is assessed through realistic simulations of up to 40 e-puck robots. In particular, we model a robot swarm and its institutional controller with the goal of maintaining wireless connectivity, and successfully compare our model predictions and simulation results with previously reported results, obtained by using finite state automaton models and controllers.

Agent independent task planning

Science.gov (United States)

Davis, William S.

1990-01-01

Agent-Independent Planning is a technique that allows the construction of activity plans without regard to the agent that will perform them. Once generated, a plan is then validated and translated into instructions for a particular agent, whether a robot, crewmember, or software-based control system. Because Space Station Freedom (SSF) is planned for orbital operations for approximately thirty years, it will almost certainly experience numerous enhancements and upgrades, including upgrades in robotic manipulators. Agent-Independent Planning provides the capability to construct plans for SSF operations, independent of specific robotic systems, by combining techniques of object oriented modeling, nonlinear planning and temporal logic. Since a plan is validated using the physical and functional models of a particular agent, new robotic systems can be developed and integrated with existing operations in a robust manner. This technique also provides the capability to generate plans for crewmembers with varying skill levels, and later apply these same plans to more sophisticated robotic manipulators made available by evolutions in technology.

You Look Human, But Act Like a Machine: Agent Appearance and Behavior Modulate Different Aspects of Human–Robot Interaction

Directory of Open Access Journals (Sweden)

Abdulaziz Abubshait

2017-08-01

Full Text Available Gaze following occurs automatically in social interactions, but the degree to which gaze is followed depends on whether an agent is perceived to have a mind, making its behavior socially more relevant for the interaction. Mind perception also modulates the attitudes we have toward others, and determines the degree of empathy, prosociality, and morality invested in social interactions. Seeing mind in others is not exclusive to human agents, but mind can also be ascribed to non-human agents like robots, as long as their appearance and/or behavior allows them to be perceived as intentional beings. Previous studies have shown that human appearance and reliable behavior induce mind perception to robot agents, and positively affect attitudes and performance in human–robot interaction. What has not been investigated so far is whether different triggers of mind perception have an independent or interactive effect on attitudes and performance in human–robot interaction. We examine this question by manipulating agent appearance (human vs. robot and behavior (reliable vs. random within the same paradigm and examine how congruent (human/reliable vs. robot/random versus incongruent (human/random vs. robot/reliable combinations of these triggers affect performance (i.e., gaze following and attitudes (i.e., agent ratings in human–robot interaction. The results show that both appearance and behavior affect human–robot interaction but that the two triggers seem to operate in isolation, with appearance more strongly impacting attitudes, and behavior more strongly affecting performance. The implications of these findings for human–robot interaction are discussed.

You Look Human, But Act Like a Machine: Agent Appearance and Behavior Modulate Different Aspects of Human-Robot Interaction.

Science.gov (United States)

Abubshait, Abdulaziz; Wiese, Eva

2017-01-01

Gaze following occurs automatically in social interactions, but the degree to which gaze is followed depends on whether an agent is perceived to have a mind, making its behavior socially more relevant for the interaction. Mind perception also modulates the attitudes we have toward others, and determines the degree of empathy, prosociality, and morality invested in social interactions. Seeing mind in others is not exclusive to human agents, but mind can also be ascribed to non-human agents like robots, as long as their appearance and/or behavior allows them to be perceived as intentional beings. Previous studies have shown that human appearance and reliable behavior induce mind perception to robot agents, and positively affect attitudes and performance in human-robot interaction. What has not been investigated so far is whether different triggers of mind perception have an independent or interactive effect on attitudes and performance in human-robot interaction. We examine this question by manipulating agent appearance (human vs. robot) and behavior (reliable vs. random) within the same paradigm and examine how congruent (human/reliable vs. robot/random) versus incongruent (human/random vs. robot/reliable) combinations of these triggers affect performance (i.e., gaze following) and attitudes (i.e., agent ratings) in human-robot interaction. The results show that both appearance and behavior affect human-robot interaction but that the two triggers seem to operate in isolation, with appearance more strongly impacting attitudes, and behavior more strongly affecting performance. The implications of these findings for human-robot interaction are discussed.

Multi-Robot Remote Interaction with FS-MAS

Directory of Open Access Journals (Sweden)

Yunliang Jiang

2013-02-01

Full Text Available The need to reduce bandwidth, improve productivity, autonomy and the scalability in multi-robot teleoperation has been recognized for a long time. In this article we propose a novel finite state machine mobile agent based on the network interaction service model, namely FS-MAS. This model consists of three finite state machines, namely the Finite State Mobile Agent (FS-Agent, which is the basic service module. The Service Content Finite State Machine (Content-FS, using the XML language to define workflow, to describe service content and service computation process. The Mobile Agent computation model Finite State Machine (MACM-FS, used to describe the service implementation. Finally, we apply this service model to the multi-robot system, the initial realization completing complex tasks in the form of multi-robot scheduling. This demonstrates that the robot has greatly improved intelligence, and provides a wide solution space for critical issues such as task division, rational and efficient use of resource and multi-robot collaboration.

From multicultural agents to culture‐aware robots

DEFF Research Database (Denmark)

Rehm, Matthias

2013-01-01

In previous research we showed how a cross‐cultural multimodal corpus of human face to face interactions can serve as empirical foundation for implementing multicultural agents (e.g. Rehm et al. 2009). To this end, the corpus has been annotated in relation to a number of communicative phenomena...... of the system have to create the behavior themselves, allowing us to collect a cross‐cultural database of behavioral parameters for the robotic system under development. This reduces any subjective or cultural bias that was previously introduced. Instead, the cross‐cultural database of behavioral parameters......, there have always been some discomforts about it due to the following reasons: - Subjectivity of the annotation - Cultural bias of the annotation and the implementation/design of the agents - Applicability of results to agents (they might represent a culture of their own) Meanwhile, we have moved to physical...

Design of a Multi Agent Architecture for Robot Soccer. A Case Study

NARCIS (Netherlands)

Poel, Mannes; Seesink, R.A.; Schoute, Albert L.; Dierssen, W.; Kooij, N.

A Multi Agent System (MAS) for the FIRA Mirosot League is presented. This MAS allows a general number of players and is used in the 5 against 5 and 7 against 7 competition. In the MAS there is coach agent and n (the number of robots in the team) player agents. There is a one to one correspondence

SpikingLab: modelling agents controlled by Spiking Neural Networks in Netlogo.

Science.gov (United States)

Jimenez-Romero, Cristian; Johnson, Jeffrey

2017-01-01

The scientific interest attracted by Spiking Neural Networks (SNN) has lead to the development of tools for the simulation and study of neuronal dynamics ranging from phenomenological models to the more sophisticated and biologically accurate Hodgkin-and-Huxley-based and multi-compartmental models. However, despite the multiple features offered by neural modelling tools, their integration with environments for the simulation of robots and agents can be challenging and time consuming. The implementation of artificial neural circuits to control robots generally involves the following tasks: (1) understanding the simulation tools, (2) creating the neural circuit in the neural simulator, (3) linking the simulated neural circuit with the environment of the agent and (4) programming the appropriate interface in the robot or agent to use the neural controller. The accomplishment of the above-mentioned tasks can be challenging, especially for undergraduate students or novice researchers. This paper presents an alternative tool which facilitates the simulation of simple SNN circuits using the multi-agent simulation and the programming environment Netlogo (educational software that simplifies the study and experimentation of complex systems). The engine proposed and implemented in Netlogo for the simulation of a functional model of SNN is a simplification of integrate and fire (I&F) models. The characteristics of the engine (including neuronal dynamics, STDP learning and synaptic delay) are demonstrated through the implementation of an agent representing an artificial insect controlled by a simple neural circuit. The setup of the experiment and its outcomes are described in this work.

A Multi-Agent Approach to the Simulation of Robotized Manufacturing Systems

Science.gov (United States)

Foit, K.; Gwiazda, A.; Banaś, W.

2016-08-01

The recent years of eventful industry development, brought many competing products, addressed to the same market segment. The shortening of a development cycle became a necessity if the company would like to be competitive. Because of switching to the Intelligent Manufacturing model the industry search for new scheduling algorithms, while the traditional ones do not meet the current requirements. The agent-based approach has been considered by many researchers as an important way of evolution of modern manufacturing systems. Due to the properties of the multi-agent systems, this methodology is very helpful during creation of the model of production system, allowing depicting both processing and informational part. The complexity of such approach makes the analysis impossible without the computer assistance. Computer simulation still uses a mathematical model to recreate a real situation, but nowadays the 2D or 3D virtual environments or even virtual reality have been used for realistic illustration of the considered systems. This paper will focus on robotized manufacturing system and will present the one of possible approaches to the simulation of such systems. The selection of multi-agent approach is motivated by the flexibility of this solution that offers the modularity, robustness and autonomy.

Caregivers' requirements for in-home robotic agent for supporting community-living elderly subjects with cognitive impairment.

Science.gov (United States)

Faucounau, Véronique; Wu, Ya-Huei; Boulay, Mélodie; Maestrutti, Marina; Rigaud, Anne-Sophie

2009-01-01

Older people are an important and growing sector of the population. This demographic change raises the profile of frailty and disability within the world's population. In such conditions, many old people need aides to perform daily activities. Most of the support is given by family members who are now a new target in the therapeutic approach. With advances in technology, robotics becomes increasingly important as a means of supporting older people at home. In order to ensure appropriate technology, 30 caregivers filled out a self-administered questionnaire including questions on needs to support their proxy and requirements concerning the robotic agent's functions and modes of action. This paper points out the functions to be integrated into the robot in order to support caregivers in the care of their proxy. The results also show that caregivers have a positive attitude towards robotic agents.

Modelling of Hydraulic Robot

DEFF Research Database (Denmark)

Madsen, Henrik; Zhou, Jianjun; Hansen, Lars Henrik

1997-01-01

This paper describes a case study of identifying the physical model (or the grey box model) of a hydraulic test robot. The obtained model is intended to provide a basis for model-based control of the robot. The physical model is formulated in continuous time and is derived by application...

A Bayesian Developmental Approach to Robotic Goal-Based Imitation Learning.

Directory of Open Access Journals (Sweden)

Michael Jae-Yoon Chung

Full Text Available A fundamental challenge in robotics today is building robots that can learn new skills by observing humans and imitating human actions. We propose a new Bayesian approach to robotic learning by imitation inspired by the developmental hypothesis that children use self-experience to bootstrap the process of intention recognition and goal-based imitation. Our approach allows an autonomous agent to: (i learn probabilistic models of actions through self-discovery and experience, (ii utilize these learned models for inferring the goals of human actions, and (iii perform goal-based imitation for robotic learning and human-robot collaboration. Such an approach allows a robot to leverage its increasing repertoire of learned behaviors to interpret increasingly complex human actions and use the inferred goals for imitation, even when the robot has very different actuators from humans. We demonstrate our approach using two different scenarios: (i a simulated robot that learns human-like gaze following behavior, and (ii a robot that learns to imitate human actions in a tabletop organization task. In both cases, the agent learns a probabilistic model of its own actions, and uses this model for goal inference and goal-based imitation. We also show that the robotic agent can use its probabilistic model to seek human assistance when it recognizes that its inferred actions are too uncertain, risky, or impossible to perform, thereby opening the door to human-robot collaboration.

MATHEMATICAL MODEL MANIPULATOR ROBOTS

Directory of Open Access Journals (Sweden)

O. N. Krakhmalev

2015-12-01

Full Text Available A mathematical model to describe the dynamics of manipulator robots. Mathematical model are the implementation of the method based on the Lagrange equation and using the transformation matrices of elastic coordinates. Mathematical model make it possible to determine the elastic deviations of manipulator robots from programmed motion trajectories caused by elastic deformations in hinges, which are taken into account in directions of change of the corresponding generalized coordinates. Mathematical model is approximated and makes it possible to determine small elastic quasi-static deviations and elastic vibrations. The results of modeling the dynamics by model are compared to the example of a two-link manipulator system. The considered model can be used when performing investigations of the mathematical accuracy of the manipulator robots.

Representing affective facial expressions for robots and embodied conversational agents by facial landmarks

NARCIS (Netherlands)

Liu, C.; Ham, J.R.C.; Postma, E.O.; Midden, C.J.H.; Joosten, B.; Goudbeek, M.

2013-01-01

Affective robots and embodied conversational agents require convincing facial expressions to make them socially acceptable. To be able to virtually generate facial expressions, we need to investigate the relationship between technology and human perception of affective and social signals. Facial

Kinematic Model of NAO Humanoid Robot

Directory of Open Access Journals (Sweden)

Miloš D. Jovanović

2014-06-01

Full Text Available This paper presents synthesis of kinematic model of NAO humanoid robot of Aldebaran Robotics. NAO humanoid robot has complex kinematic structure with 25 active degrees of freedom (DOF. Humanoid system is formed through 5 mutually depended kinematic chains. After that we applied standard aspects of kinematic chains synthesis and Denavit-Hartenberg parameters of each of 5 chains of robotic structure were introduced. Also, mutual relationships between chains were described, as well as their physical and structural dependence. Generated kinematic model will be the starting point for further dynamical modeling of NAO humanoid robot and motion synthesis on actual platform.

Action observation and robotic agents: learning and anthropomorphism.

Science.gov (United States)

Press, Clare

2011-05-01

The 'action observation network' (AON), which is thought to translate observed actions into motor codes required for their execution, is biologically tuned: it responds more to observation of human, than non-human, movement. This biological specificity has been taken to support the hypothesis that the AON underlies various social functions, such as theory of mind and action understanding, and that, when it is active during observation of non-human agents like humanoid robots, it is a sign of ascription of human mental states to these agents. This review will outline evidence for biological tuning in the AON, examining the features which generate it, and concluding that there is evidence for tuning to both the form and kinematic profile of observed movements, and little evidence for tuning to belief about stimulus identity. It will propose that a likely reason for biological tuning is that human actions, relative to non-biological movements, have been observed more frequently while executing corresponding actions. If the associative hypothesis of the AON is correct, and the network indeed supports social functioning, sensorimotor experience with non-human agents may help us to predict, and therefore interpret, their movements. Copyright © 2011 Elsevier Ltd. All rights reserved.

The Tactile Ethics of Soft Robotics: Designing Wisely for Human-Robot Interaction.

Science.gov (United States)

Arnold, Thomas; Scheutz, Matthias

2017-06-01

Soft robots promise an exciting design trajectory in the field of robotics and human-robot interaction (HRI), promising more adaptive, resilient movement within environments as well as a safer, more sensitive interface for the objects or agents the robot encounters. In particular, tactile HRI is a critical dimension for designers to consider, especially given the onrush of assistive and companion robots into our society. In this article, we propose to surface an important set of ethical challenges for the field of soft robotics to meet. Tactile HRI strongly suggests that soft-bodied robots balance tactile engagement against emotional manipulation, model intimacy on the bonding with a tool not with a person, and deflect users from personally and socially destructive behavior the soft bodies and surfaces could normally entice.

How to Touch Humans : Guidelines for Social Agents and Robots that can Touch

NARCIS (Netherlands)

Erp, J.B.F. van; Toet, A.

2013-01-01

Touch is an essential channel in interpersonal and affective communication, yet most social agents currently lack the capability to touch the user. In this paper we show the credibility of three premises that make the case that providing touch capability to social robots will increase their

Dynamic Modelling Of A SCARA Robot

Science.gov (United States)

Turiel, J. Perez; Calleja, R. Grossi; Diez, V. Gutierrez

1987-10-01

This paper describes a method for modelling industrial robots that considers dynamic approach to manipulation systems motion generation, obtaining the complete dynamic model for the mechanic part of the robot and taking into account the dynamic effect of actuators acting at the joints. For a four degree of freedom SCARA robot we obtain the dynamic model for the basic (minimal) configuration, that is, the three degrees of freedom that allow us to place the robot end effector in a desired point, using the Lagrange Method to obtain the dynamic equations in matrix form. The manipulator is considered to be a set of rigid bodies inter-connected by joints in the form of simple kinematic pairs. Then, the state space model is obtained for the actuators that move the robot joints, uniting the models of the single actuators, that is, two DC permanent magnet servomotors and an electrohydraulic actuator. Finally, using a computer simulation program written in FORTRAN language, we can compute the matrices of the complete model.

Snake Robots Modelling, Mechatronics, and Control

CERN Document Server

Liljebäck, Pål; Stavdahl, Øyvind; Gravdahl, Jan Tommy

2013-01-01

Snake Robots is a novel treatment of theoretical and practical topics related to snake robots: robotic mechanisms designed to move like biological snakes and able to operate in challenging environments in which human presence is either undesirable or impossible. Future applications of such robots include search and rescue, inspection and maintenance, and subsea operations. Locomotion in unstructured environments is a focus for this book. The text targets the disparate muddle of approaches to modelling, development and control of snake robots in current literature, giving a unified presentation of recent research results on snake robot locomotion to increase the reader’s basic understanding of these mechanisms and their motion dynamics and clarify the state of the art in the field. The book is a complete treatment of snake robotics, with topics ranging from mathematical modelling techniques, through mechatronic design and implementation, to control design strategies. The development of two snake robots is de...

Flocking algorithm for autonomous flying robots.

Science.gov (United States)

Virágh, Csaba; Vásárhelyi, Gábor; Tarcai, Norbert; Szörényi, Tamás; Somorjai, Gergő; Nepusz, Tamás; Vicsek, Tamás

2014-06-01

Animal swarms displaying a variety of typical flocking patterns would not exist without the underlying safe, optimal and stable dynamics of the individuals. The emergence of these universal patterns can be efficiently reconstructed with agent-based models. If we want to reproduce these patterns with artificial systems, such as autonomous aerial robots, agent-based models can also be used in their control algorithms. However, finding the proper algorithms and thus understanding the essential characteristics of the emergent collective behaviour requires thorough and realistic modeling of the robot and also the environment. In this paper, we first present an abstract mathematical model of an autonomous flying robot. The model takes into account several realistic features, such as time delay and locality of communication, inaccuracy of the on-board sensors and inertial effects. We present two decentralized control algorithms. One is based on a simple self-propelled flocking model of animal collective motion, the other is a collective target tracking algorithm. Both algorithms contain a viscous friction-like term, which aligns the velocities of neighbouring agents parallel to each other. We show that this term can be essential for reducing the inherent instabilities of such a noisy and delayed realistic system. We discuss simulation results on the stability of the control algorithms, and perform real experiments to show the applicability of the algorithms on a group of autonomous quadcopters. In our case, bio-inspiration works in two ways. On the one hand, the whole idea of trying to build and control a swarm of robots comes from the observation that birds tend to flock to optimize their behaviour as a group. On the other hand, by using a realistic simulation framework and studying the group behaviour of autonomous robots we can learn about the major factors influencing the flight of bird flocks.

Human-robot collaboration for a shared mission

OpenAIRE

Karami , Abir-Beatrice; Jeanpierre , Laurent; Mouaddib , Abdel-Illah

2010-01-01

International audience; We are interested in collaboration domains between a robot and a human partner, the partners share a common mission without an explicit communication about their plans. The decision process of the robot agent should consider the presence of its human partner. Also, the robot planning should be flexible to human comfortability and all possible changes in the shared environment. To solve the problem of human-robot collaborationwith no communication, we present a model th...

The ten rules of touch : Guidelines for social agents and robots that can touch

NARCIS (Netherlands)

Erp, J.B.F. van

2012-01-01

Touching is essential in interpersonal and affective communication, yet most social agents lack the capability to touch the user. In this paper we show the credibility of three premises that make the case that providing touch capability to social robots will increase their effectiveness in

Anthropomimetic Robots: Concept, Construction and Modelling

Directory of Open Access Journals (Sweden)

Alan Diamond

2012-11-01

Full Text Available An anthropomimetic robot is one that closely copies the mechanics of the human body by having a human-like jointed skeleton moved by compliant muscle-like actuators. This paper describes the progress achieved in building anthropomimetic torsos in two projects, CRONOS and ECCEROBOT. In each, the bones were hand-moulded in a thermoplastic and the muscles were implemented by DC motors shortening and extending elastic tendons. Anthropomimetic robots differ from conventionally engineered robots by having complex joints and compliant tendon driven actuation that can cross more than one joint. Taken together, these characteristics make the robots unsuitable for control by standard methods, and so the ability to model them is important for developing heuristic methods of control and also for providing forward models. The robots were modelled using physics-based techniques which enable the study of the generation of movements and also of interactions with arbitrary objects. The lightweight and compliant structure of the robots was found to be safe for human proximity and contact.

Contrasting Web Robot and Human Behaviors with Network Models

OpenAIRE

Brown, Kyle; Doran, Derek

2018-01-01

The web graph is a commonly-used network representation of the hyperlink structure of a website. A network of similar structure to the web graph, which we call the session graph has properties that reflect the browsing habits of the agents in the web server logs. In this paper, we apply session graphs to compare the activity of humans against web robots or crawlers. Understanding these properties will enable us to improve models of HTTP traffic, which can be used to predict and generate reali...

Modelling, simulation and validation of the industrial robot

Directory of Open Access Journals (Sweden)

Aleksandrov Slobodan Č.

2014-01-01

Full Text Available In this paper, a DH model of industrial robot, with anthropomorphic configuration and five degrees of freedom - Mitsubishi RV2AJ, is developed. The model is verified on the example robot Mitsubishi RV2AJ. In paper detailed represented the complete mathematical model of the robot and the parameters of the programming. On the basis of this model, simulation of robot motion from point to point is performed, as well as the continuous movement of the pre-defined path. Also, programming of industrial robots identical to simulation programs is made, and comparative analysis of real and simulated experiment is shown. In the final section, a detailed analysis of robot motion is described.

The internet and intelligent machines: search engines, agents and robots

International Nuclear Information System (INIS)

Achenbach, S.; Alfke, H.

2000-01-01

The internet plays an important role in a growing number of medical applications. Finding relevant information is not always easy as the amount of available information on the Web is rising quickly. Even the best Search Engines can only collect links to a fraction of all existing Web pages. In addition, many of these indexed documents have been changed or deleted. The vast majority of information on the Web is not searchable with conventional methods. New search strategies, technologies and standards are combined in Intelligent Search Agents (ISA) an Robots, which can retrieve desired information in a specific approach. Conclusion: The article describes differences between ISAs and conventional Search Engines and how communication between Agents improves their ability to find information. Examples of existing ISAs are given and the possible influences on the current and future work in radiology is discussed. (orig.) [de

Modeling and identification for high-performance robot control : an RRR-robotic arm case study

NARCIS (Netherlands)

Kostic, D.; Jager, de A.G.; Steinbuch, M.; Hensen, R.H.A.

2004-01-01

We explain a procedure for getting models of robot kinematics and dynamics that are appropriate for robot control design. The procedure consists of the following steps: (i) derivation of robot kinematic and dynamic models and establishing correctness of their structures; (ii) experimental estimation

This "Ethical Trap" Is for Roboticists, Not Robots: On the Issue of Artificial Agent Ethical Decision-Making.

Science.gov (United States)

Miller, Keith W; Wolf, Marty J; Grodzinsky, Frances

2017-04-01

In this paper we address the question of when a researcher is justified in describing his or her artificial agent as demonstrating ethical decision-making. The paper is motivated by the amount of research being done that attempts to imbue artificial agents with expertise in ethical decision-making. It seems clear that computing systems make decisions, in that they make choices between different options; and there is scholarship in philosophy that addresses the distinction between ethical decision-making and general decision-making. Essentially, the qualitative difference between ethical decisions and general decisions is that ethical decisions must be part of the process of developing ethical expertise within an agent. We use this distinction in examining publicity surrounding a particular experiment in which a simulated robot attempted to safeguard simulated humans from falling into a hole. We conclude that any suggestions that this simulated robot was making ethical decisions were misleading.

Robot modelling; Control and applications with software

Energy Technology Data Exchange (ETDEWEB)

Ranky, P G; Ho, C Y

1985-01-01

This book provides a ''picture'' of robotics covering both the theoretical aspect of modeling as well as the practical and design aspects of: robot programming; robot tooling and automated hand changing; implementation planning; testing; and software design for robot systems. The authors present an introduction to robotics with a systems approach. They describe not only the tasks relating to a single robot (or arm) but also systems of robots working together on a product or several products.

Towards Bio-Inspired Chromatic Behaviours in Surveillance Robots

Directory of Open Access Journals (Sweden)

Sampath Kumar Karutaa Gnaniar

2016-09-01

Full Text Available The field of Robotics is ever growing at the same time as posing enormous challenges. Numerous works has been done in biologically inspired robotics emulating models, systems and elements of nature for the purpose of solving traditional robotics problems. Chromatic behaviours are abundant in nature across a variety of living species to achieve camouflage, signaling, and temperature regulation. The ability of these creatures to successfully blend in with their environment and communicate by changing their colour is the fundamental inspiration for our research work. In this paper, we present dwarf chameleon inspired chromatic behaviour in the context of an autonomous surveillance robot, “PACHONDHI”. In our experiments, we successfully validated the ability of the robot to autonomously change its colour in relation to the terrain that it is traversing for maximizing detectability to friendly security agents and minimizing exposure to hostile agents, as well as to communicate with fellow cooperating robots.

Developing new behavior strategies of robot soccer team SjF TUKE Robotics

Directory of Open Access Journals (Sweden)

Mikuláš Hajduk

2016-09-01

Full Text Available There are too many types of robotic soccer approaches at present. SjF TUKE Robotics, who won robot soccer world tournament for year 2010 in category MiroSot, is a team with multiagent system approach. They have one main agent (master and five agent players, represented by robots. There is a point of view, in the article, for code programmer how to create new behavior strategies by creating a new code for master. There is a methodology how to prepare and create it following some rules.

Model Driven Software Development for Agricultural Robotics

DEFF Research Database (Denmark)

Larsen, Morten

The design and development of agricultural robots, consists of both mechan- ical, electrical and software components. All these components must be de- signed and combined such that the overall goal of the robot is fulfilled. The design and development of these systems require collaboration between...... processing, control engineering, etc. This thesis proposes a Model-Driven Software Develop- ment based approach to model, analyse and partially generate the software implementation of a agricultural robot. Furthermore, Guidelines for mod- elling the architecture of an agricultural robots are provided......, assisting with bridging the different engineering disciplines. Timing play an important role in agricultural robotic applications, synchronisation of robot movement and implement actions is important in order to achieve precision spraying, me- chanical weeding, individual feeding, etc. Discovering...

On Robot Modelling using Maple

OpenAIRE

Wallén, Johanna

2007-01-01

This report studies robot modelling by means of the computer algebra tool Maple. First coordinate systems are described, and the more general way with transformation matrices is chosen in the further work. The position kinematics of the robot are then described by homogeneous transformations. The Denavit-Hartenberg representation is used, which is a systematic way to develop the forward kinematics for rigid robots. The velocity kinematics is then described by the Jacobian. The industrial robo...

Robots with Internal Models: A Route to Self-Aware and Hence Safer Robots

Science.gov (United States)

Winfield, Alan F. T.

The following sections are included: * Introduction * Internal Models and Self-Awareness * Internal Model-Based Architecture for Robot Safety * The Internal Model * The Consequence Evaluator * The Object Tracker-Localizer * Towards an Ethical Robot * Challenges and Open Questions * Discussion: The Way Forward * Summary and Conclusions

Extending NGOMSL Model for Human-Humanoid Robot Interaction in the Soccer Robotics Domain

Directory of Open Access Journals (Sweden)

Rajesh Elara Mohan

2008-01-01

Full Text Available In the field of human-computer interaction, the Natural Goals, Operators, Methods, and Selection rules Language (NGOMSL model is one of the most popular methods for modelling knowledge and cognitive processes for rapid usability evaluation. The NGOMSL model is a description of the knowledge that a user must possess to operate the system represented as elementary actions for effective usability evaluations. In the last few years, mobile robots have been exhibiting a stronger presence in commercial markets and very little work has been done with NGOMSL modelling for usability evaluations in the human-robot interaction discipline. This paper focuses on extending the NGOMSL model for usability evaluation of human-humanoid robot interaction in the soccer robotics domain. The NGOMSL modelled human-humanoid interaction design of Robo-Erectus Junior was evaluated and the results of the experiments showed that the interaction design was able to find faults in an average time of 23.84 s. Also, the interaction design was able to detect the fault within the 60 s in 100% of the cases. The Evaluated Interaction design was adopted by our Robo-Erectus Junior version of humanoid robots in the RoboCup 2007 humanoid soccer league.

Modeling and identification for robot motion control

NARCIS (Netherlands)

Kostic, D.; Jager, de A.G.; Steinbuch, M.; Kurfess, T.R.

2004-01-01

This chapter deals with the problems of robot modelling and identification for high-performance model-based motion control. A derivation of robot kinematic and dynamic models was explained. Modelling of friction effects was also discussed. Use of a writing task to establish correctness of the models

Robot transparency, trust and utility

Science.gov (United States)

Wortham, Robert H.; Theodorou, Andreas

2017-07-01

As robot reasoning becomes more complex, debugging becomes increasingly hard based solely on observable behaviour, even for robot designers and technical specialists. Similarly, non-specialist users have difficulty creating useful mental models of robot reasoning from observations of robot behaviour. The EPSRC Principles of Robotics mandate that our artefacts should be transparent, but what does this mean in practice, and how does transparency affect both trust and utility? We investigate this relationship in the literature and find it to be complex, particularly in nonindustrial environments where, depending on the application and purpose of the robot, transparency may have a wider range of effects on trust and utility. We outline our programme of research to support our assertion that it is nevertheless possible to create transparent agents that are emotionally engaging despite having a transparent machine nature.

Towards the Verification of Human-Robot Teams

Science.gov (United States)

Fisher, Michael; Pearce, Edward; Wooldridge, Mike; Sierhuis, Maarten; Visser, Willem; Bordini, Rafael H.

2005-01-01

Human-Agent collaboration is increasingly important. Not only do high-profile activities such as NASA missions to Mars intend to employ such teams, but our everyday activities involving interaction with computational devices falls into this category. In many of these scenarios, we are expected to trust that the agents will do what we expect and that the agents and humans will work together as expected. But how can we be sure? In this paper, we bring together previous work on the verification of multi-agent systems with work on the modelling of human-agent teamwork. Specifically, we target human-robot teamwork. This paper provides an outline of the way we are using formal verification techniques in order to analyse such collaborative activities. A particular application is the analysis of human-robot teams intended for use in future space exploration.

Fixed geometric formation structure in formation control problem for group of robots with dynamically changing number of robots in the group

Directory of Open Access Journals (Sweden)

N. S. Morozova

2015-01-01

Full Text Available The article considers a problem of the decentralization-based approach to formation control of a group of agents, which simulate mobile autonomous robots. The agents use only local information limited by the covering range of their sensors. The agents have to build and maintain the formation, which fits to the defined target geometric formation structure with desired accuracy during the movement to the target point. At any point in time the number of agents in the group can change unexpectedly (for example, as a result of the agent failure or if a new agent joins the group.The aim of the article is to provide the base control rule, which solves the formation control problem, and to develop its modifications, which provide the correct behavior in case the agent number in the group is not equal to the size of the target geometric formation structure. The proposed base control rule, developed by the author, uses the method of involving virtual leaders. The coordinates of the virtual leaders and also the priority to follow the specific leader are calculated by each agent itself according to specific rules.The following results are presented in the article: the base control rule for solving the formation control problem, its modifications for the cases when the number of agents is greater/less than the size of the target geometric formation structure and also the computer modeling results proving the efficiency of the modified control rules. The specific feature of the control rule, developed by the author, is that each agent itself calculates the virtual leaders and each agent performs dynamic choice of the place within the formation (there is no predefined one-to-one relation between agents and places within the geometric formation structure. The results, provided in this article, can be used in robotics for developing control algorithms for the tasks, which require preserving specific relational positions among the agents while moving. One of the

Autonomous Shepherding Behaviors of Multiple Target Steering Robots.

Science.gov (United States)

Lee, Wonki; Kim, DaeEun

2017-11-25

This paper presents a distributed coordination methodology for multi-robot systems, based on nearest-neighbor interactions. Among many interesting tasks that may be performed using swarm robots, we propose a biologically-inspired control law for a shepherding task, whereby a group of external agents drives another group of agents to a desired location. First, we generated sheep-like robots that act like a flock. We assume that each agent is capable of measuring the relative location and velocity to each of its neighbors within a limited sensing area. Then, we designed a control strategy for shepherd-like robots that have information regarding where to go and a steering ability to control the flock, according to the robots' position relative to the flock. We define several independent behavior rules; each agent calculates to what extent it will move by summarizing each rule. The flocking sheep agents detect the steering agents and try to avoid them; this tendency leads to movement of the flock. Each steering agent only needs to focus on guiding the nearest flocking agent to the desired location. Without centralized coordination, multiple steering agents produce an arc formation to control the flock effectively. In addition, we propose a new rule for collecting behavior, whereby a scattered flock or multiple flocks are consolidated. From simulation results with multiple robots, we show that each robot performs actions for the shepherding behavior, and only a few steering agents are needed to control the whole flock. The results are displayed in maps that trace the paths of the flock and steering robots. Performance is evaluated via time cost and path accuracy to demonstrate the effectiveness of this approach.

Modeling humanoid swarm robots with petri nets

OpenAIRE

Maharjan, Bikee

2015-01-01

Master's thesis in Computer science Robots have become a hot topic in today‟s electronic world. There are many definitions for it. One of the definition in Oxford dictionary states “a robot is a machine capable for carrying out a complex series of action automatically especially one programmable by a computer”. This paper deals with a special kind of robot, which is also known as humanoid robot. These robots are replication of human beings with head, torso, arms and legs. A model of hum...

Cloud Robotics Model

OpenAIRE

Mester, Gyula

2015-01-01

Cloud Robotics was born from the merger of service robotics and cloud technologies. It allows robots to benefit from the powerful computational, storage, and communications resources of modern data centres. Cloud robotics allows robots to take advantage of the rapid increase in data transfer rates to offload tasks without hard real time requirements. Cloud Robotics has rapidly gained momentum with initiatives by companies such as Google, Willow Garage and Gostai as well as more than a dozen a...

Developing robotic behavior using a genetic programming model

International Nuclear Information System (INIS)

Pryor, R.J.

1998-01-01

This report describes the methodology for using a genetic programming model to develop tracking behaviors for autonomous, microscale robotic vehicles. The use of such vehicles for surveillance and detection operations has become increasingly important in defense and humanitarian applications. Through an evolutionary process similar to that found in nature, the genetic programming model generates a computer program that when downloaded onto a robotic vehicle's on-board computer will guide the robot to successfully accomplish its task. Simulations of multiple robots engaged in problem-solving tasks have demonstrated cooperative behaviors. This report also discusses the behavior model produced by genetic programming and presents some results achieved during the study

Dynamic Modelling and Adaptive Traction Control for Mobile Robots

Directory of Open Access Journals (Sweden)

A. Albagul

2004-09-01

Full Text Available Mobile robots have received a great deal of research in recent years. A significant amount of research has been published in many aspects related to mobile robots. Most of the research is devoted to design and develop some control techniques for robot motion and path planning. A large number of researchers have used kinematic models to develop motion control strategy for mobile robots. Their argument and assumption that these models are valid if the robot has low speed, low acceleration and light load. However, dynamic modelling of mobile robots is very important as they are designed to travel at higher speed and perform heavy duty work. This paper presents and discusses a new approach to develop a dynamic model and control strategy for wheeled mobile robot which I modelled as a rigid body that roles on two wheels and a castor. The motion control strategy consists of two levels. The first level is dealing with the dynamic of the system and denoted as ‘Low’ level controller. The second level is developed to take care of path planning and trajectory generation.

Modelling and Control of a Mobile Robot

DEFF Research Database (Denmark)

Christensen, Georg Kronborg

1998-01-01

In order to control a mobile robot, kinematic odels as well as dynamic models are required. This parer describes these basic models for an experimental mobile robot under construction at the Department of Control and Engineering Design. A description of a set of trajectory control rules is given...

Autonomous Shepherding Behaviors of Multiple Target Steering Robots

Directory of Open Access Journals (Sweden)

Wonki Lee

2017-11-01

Full Text Available This paper presents a distributed coordination methodology for multi-robot systems, based on nearest-neighbor interactions. Among many interesting tasks that may be performed using swarm robots, we propose a biologically-inspired control law for a shepherding task, whereby a group of external agents drives another group of agents to a desired location. First, we generated sheep-like robots that act like a flock. We assume that each agent is capable of measuring the relative location and velocity to each of its neighbors within a limited sensing area. Then, we designed a control strategy for shepherd-like robots that have information regarding where to go and a steering ability to control the flock, according to the robots’ position relative to the flock. We define several independent behavior rules; each agent calculates to what extent it will move by summarizing each rule. The flocking sheep agents detect the steering agents and try to avoid them; this tendency leads to movement of the flock. Each steering agent only needs to focus on guiding the nearest flocking agent to the desired location. Without centralized coordination, multiple steering agents produce an arc formation to control the flock effectively. In addition, we propose a new rule for collecting behavior, whereby a scattered flock or multiple flocks are consolidated. From simulation results with multiple robots, we show that each robot performs actions for the shepherding behavior, and only a few steering agents are needed to control the whole flock. The results are displayed in maps that trace the paths of the flock and steering robots. Performance is evaluated via time cost and path accuracy to demonstrate the effectiveness of this approach.

Modelling robot's behaviour using finite automata

Science.gov (United States)

Janošek, Michal; Žáček, Jaroslav

2017-07-01

This paper proposes a model of a robot's behaviour described by finite automata. We split robot's knowledge into several knowledge bases which are used by the inference mechanism of the robot's expert system to make a logic deduction. Each knowledgebase is dedicated to the particular behaviour domain and the finite automaton helps us switching among these knowledge bases with the respect of actual situation. Our goal is to simplify and reduce complexity of one big knowledgebase splitting it into several pieces. The advantage of this model is that we can easily add new behaviour by adding new knowledgebase and add this behaviour into the finite automaton and define necessary states and transitions.

Simulation-Based Internal Models for Safer Robots

Directory of Open Access Journals (Sweden)

Christian Blum

2018-01-01

Full Text Available In this paper, we explore the potential of mobile robots with simulation-based internal models for safety in highly dynamic environments. We propose a robot with a simulation of itself, other dynamic actors and its environment, inside itself. Operating in real time, this simulation-based internal model is able to look ahead and predict the consequences of both the robot’s own actions and those of the other dynamic actors in its vicinity. Hence, the robot continuously modifies its own actions in order to actively maintain its own safety while also achieving its goal. Inspired by the problem of how mobile robots could move quickly and safely through crowds of moving humans, we present experimental results which compare the performance of our internal simulation-based controller with a purely reactive approach as a proof-of-concept study for the practical use of simulation-based internal models.

Specification of a STEP Based Reference Model for Exchange of Robotics Models

DEFF Research Database (Denmark)

Haenisch, Jochen; Kroszynski, Uri; Ludwig, Arnold

robot programming, the descriptions of geometry, kinematics, robotics, dynamics, and controller data using STEP are addressed as major goals of the project.The Project Consortium has now released the "Specificatin of a STEP Based Reference Model for Exchange of Robotics Models" on which a series......ESPRIT Project 6457: "Interoperability of Standards for Robotics in CIME" (InterRob) belongs to the Subprogram "Computer Integrated Manufacturing and Engineering" of ESPRIT, the European Specific Programme for Research and Development in Information Technology supported by the European Commision....... InterRob aims to develop an integrated solution to precision manufacturing by combining product data and database technologies with robotic off-line programming and simulation. Benefits arise from the use of high level simulation tools and developing standards for the exchange of product model data...

Simulating an elastic bipedal robot based on musculoskeletal modeling

NARCIS (Netherlands)

Bortoletto, Roberto; Sartori, Massimo; He, Fuben; Pagello, Enrico

2012-01-01

Many of the processes involved into the synthesis of human motion have much in common with problems found in robotics research. This paper describes the modeling and the simulation of a novel bipedal robot based on series elastic actuators [1]. The robot model takes in- spiration from the human

Research on Modeling Technology of Virtual Robot Based on LabVIEW

Science.gov (United States)

Wang, Z.; Huo, J. L.; Y Sun, L.; Y Hao, X.

2017-12-01

Because of the dangerous working environment, the underwater operation robot for nuclear power station needs manual teleoperation. In the process of operation, it is necessary to guide the position and orientation of the robot in real time. In this paper, the geometric modeling of the virtual robot and the working environment is accomplished by using SolidWorks software, and the accurate modeling and assembly of the robot are realized. Using LabVIEW software to read the model, and established the manipulator forward kinematics and inverse kinematics model, and realized the hierarchical modeling of virtual robot and computer graphics modeling. Experimental results show that the method studied in this paper can be successfully applied to robot control system.

Software toolkit for modeling, simulation and control of soft robots

OpenAIRE

Coevoet , Eulalie; Morales-Bieze , Thor; Largilliere , Frederick; Zhang , Zhongkai; Thieffry , Maxime; Sanz-Lopez , Mario; Carrez , Bruno; Marchal , Damien; Goury , Olivier; Dequidt , Jeremie; Duriez , Christian

2017-01-01

International audience; The technological differences between traditional robotics and soft robotics have an impact on all of the modeling tools generally in use, including direct kinematics and inverse models, Jacobians, and dynamics. Due to the lack of precise modeling and control methods for soft robots, the promising concepts of using such design for complex applications (medicine, assistance, domestic robotics...) cannot be practically implemented. This paper presents a first unified sof...

Investigating the feasibility of a BCI-driven robot-based writing agent for handicapped individuals

Science.gov (United States)

Syan, Chanan S.; Harnarinesingh, Randy E. S.; Beharry, Rishi

2014-07-01

Brain-Computer Interfaces (BCIs) predominantly employ output actuators such as virtual keyboards and wheelchair controllers to enable handicapped individuals to interact and communicate with their environment. However, BCI-based assistive technologies are limited in their application. There is minimal research geared towards granting disabled individuals the ability to communicate using written words. This is a drawback because involving a human attendant in writing tasks can entail a breach of personal privacy where the task entails sensitive and private information such as banking matters. BCI-driven robot-based writing however can provide a safeguard for user privacy where it is required. This study investigated the feasibility of a BCI-driven writing agent using the 3 degree-of- freedom Phantom Omnibot. A full alphanumerical English character set was developed and validated using a teach pendant program in MATLAB. The Omnibot was subsequently interfaced to a P300-based BCI. Three subjects utilised the BCI in the online context to communicate words to the writing robot over a Local Area Network (LAN). The average online letter-wise classification accuracy was 91.43%. The writing agent legibly constructed the communicated letters with minor errors in trajectory execution. The developed system therefore provided a feasible platform for BCI-based writing.

Investigating the feasibility of a BCI-driven robot-based writing agent for handicapped individuals

International Nuclear Information System (INIS)

Syan, Chanan S; Harnarinesingh, Randy E S; Beharry, Rishi

2014-01-01

Brain-Computer Interfaces (BCIs) predominantly employ output actuators such as virtual keyboards and wheelchair controllers to enable handicapped individuals to interact and communicate with their environment. However, BCI-based assistive technologies are limited in their application. There is minimal research geared towards granting disabled individuals the ability to communicate using written words. This is a drawback because involving a human attendant in writing tasks can entail a breach of personal privacy where the task entails sensitive and private information such as banking matters. BCI-driven robot-based writing however can provide a safeguard for user privacy where it is required. This study investigated the feasibility of a BCI-driven writing agent using the 3 degree-of- freedom Phantom Omnibot. A full alphanumerical English character set was developed and validated using a teach pendant program in MATLAB. The Omnibot was subsequently interfaced to a P300-based BCI. Three subjects utilised the BCI in the online context to communicate words to the writing robot over a Local Area Network (LAN). The average online letter-wise classification accuracy was 91.43%. The writing agent legibly constructed the communicated letters with minor errors in trajectory execution. The developed system therefore provided a feasible platform for BCI-based writing

Rapid world modelling for robotics

International Nuclear Information System (INIS)

Littile, C.Q.; Wilson, C.W.

1996-01-01

The ability to use an interactive world model, whether it is for robotics simulation or most other virtual graphical environments, relies on the users ability to create an accurate world model. Typically this is a tedious process, requiring many hours to create 3-D CAD models of the surfaces within a workspace. The goal of this ongoing project is to develop usable methods to rapidly build world models of real world workspaces. This brings structure to an unstructured environment and allows graphical based robotics control to be accomplished in a reasonable time frame when traditional CAD modelling is not enough. To accomplish this, 3D range sensors are deployed to capture surface data within the workspace. This data is then transformed into surface maps, or models. A 3D world model of the workspace is built quickly and accurately, without ever having to put people in the environment

Where neuroscience and dynamic system theory meet autonomous robotics: a contracting basal ganglia model for action selection.

Science.gov (United States)

Girard, B; Tabareau, N; Pham, Q C; Berthoz, A; Slotine, J-J

2008-05-01

Action selection, the problem of choosing what to do next, is central to any autonomous agent architecture. We use here a multi-disciplinary approach at the convergence of neuroscience, dynamical system theory and autonomous robotics, in order to propose an efficient action selection mechanism based on a new model of the basal ganglia. We first describe new developments of contraction theory regarding locally projected dynamical systems. We exploit these results to design a stable computational model of the cortico-baso-thalamo-cortical loops. Based on recent anatomical data, we include usually neglected neural projections, which participate in performing accurate selection. Finally, the efficiency of this model as an autonomous robot action selection mechanism is assessed in a standard survival task. The model exhibits valuable dithering avoidance and energy-saving properties, when compared with a simple if-then-else decision rule.

Designing Emotionally Expressive Robots

DEFF Research Database (Denmark)

Tsiourti, Christiana; Weiss, Astrid; Wac, Katarzyna

2017-01-01

Socially assistive agents, be it virtual avatars or robots, need to engage in social interactions with humans and express their internal emotional states, goals, and desires. In this work, we conducted a comparative study to investigate how humans perceive emotional cues expressed by humanoid...... robots through five communication modalities (face, head, body, voice, locomotion) and examined whether the degree of a robot's human-like embodiment affects this perception. In an online survey, we asked people to identify emotions communicated by Pepper -a highly human-like robot and Hobbit – a robot...... for robots....

Market-Based Coordination and Auditing Mechanisms for Self-Interested Multi-Robot Systems

Science.gov (United States)

Ham, MyungJoo

2009-01-01

We propose market-based coordinated task allocation mechanisms, which allocate complex tasks that require synchronized and collaborated services of multiple robot agents to robot agents, and an auditing mechanism, which ensures proper behaviors of robot agents by verifying inter-agent activities, for self-interested, fully-distributed, and…

Shape Modeling of a Concentric-tube Continuum Robot

DEFF Research Database (Denmark)

Bai, Shaoping; Xing, Charles Chuhao

2012-01-01

Concentric-tube continuum robots feature with simple and compact structures and have a great potential in medical applications. The paper is concerned with the shape modeling of a type of concentric-tube continuum robot built with a collection of super-elastic NiTiNol tubes. The mechanics...... is modeled on the basis of energy approach for both the in-plane and out-plane cases. The torsional influences on the shape of the concentric-tube robots are considered. An experimental device was build for the model validation. The results of simulation and experiments are included and analyzed....

Simplified Human-Robot Interaction: Modeling and Evaluation

Directory of Open Access Journals (Sweden)

Balazs Daniel

2013-10-01

Full Text Available In this paper a novel concept of human-robot interaction (HRI modeling is proposed. Including factors like trust in automation, situational awareness, expertise and expectations a new user experience framework is formed for industrial robots. Service Oriented Robot Operation, proposed in a previous paper, creates an abstract level in HRI and it is also included in the framework. This concept is evaluated with exhaustive tests. Results prove that significant improvement in task execution may be achieved and the new system is more usable for operators with less experience with robotics; personnel specific for small and medium enterprises (SMEs.

The embodiment of cockroach aggregation behavior in a group of micro-robots.

Science.gov (United States)

Garnier, Simon; Jost, Christian; Gautrais, Jacques; Asadpour, Masoud; Caprari, Gilles; Jeanson, Raphaël; Grimal, Anne; Theraulaz, Guy

2008-01-01

We report the faithful reproduction of the self-organized aggregation behavior of the German cockroach Blattella germanica with a group of robots. We describe the implementation of the biological model provided by Jeanson et al. in Alice robots, and we compare the behaviors of the cockroaches and the robots using the same experimental and analytical methodology. We show that the aggregation behavior of the German cockroach was successfully transferred to the Alice robot despite strong differences between robots and animals at the perceptual, actuatorial, and computational levels. This article highlights some of the major constraints one may encounter during such a work and proposes general principles to ensure that the behavioral model is accurately transferred to the artificial agents.

Static stiffness modeling of a novel hybrid redundant robot machine

International Nuclear Information System (INIS)

Li Ming; Wu Huapeng; Handroos, Heikki

2011-01-01

This paper presents a modeling method to study the stiffness of a hybrid serial-parallel robot IWR (Intersector Welding Robot) for the assembly of ITER vacuum vessel. The stiffness matrix of the basic element in the robot is evaluated using matrix structural analysis (MSA); the stiffness of the parallel mechanism is investigated by taking account of the deformations of both hydraulic limbs and joints; the stiffness of the whole integrated robot is evaluated by employing the virtual joint method and the principle of virtual work. The obtained stiffness model of the hybrid robot is analytical and the deformation results of the robot workspace under certain external load are presented.

Measuring Attitudes Towards Telepresence Robots

OpenAIRE

M Tsui, Katherine; Desai, Munjal; A. Yanco, Holly; Cramer, Henriette; Kemper, Nicander

2011-01-01

Studies using Nomura et al.’s “Negative Attitude toward Robots Scale” (NARS) [1] as an attitudinal measure have featured robots that were perceived to be autonomous, indepen- dent agents. State of the art telepresence robots require an explicit human-in-the-loop to drive the robot around. In this paper, we investigate if NARS can be used with telepresence robots. To this end, we conducted three studies in which people watched videos of telepresence robots (n=70), operated te...

Construction of multi-agent mobile robots control system in the problem of persecution with using a modified reinforcement learning method based on neural networks

Science.gov (United States)

Patkin, M. L.; Rogachev, G. N.

2018-02-01

A method for constructing a multi-agent control system for mobile robots based on training with reinforcement using deep neural networks is considered. Synthesis of the management system is proposed to be carried out with reinforcement training and the modified Actor-Critic method, in which the Actor module is divided into Action Actor and Communication Actor in order to simultaneously manage mobile robots and communicate with partners. Communication is carried out by sending partners at each step a vector of real numbers that are added to the observation vector and affect the behaviour. Functions of Actors and Critic are approximated by deep neural networks. The Critics value function is trained by using the TD-error method and the Actor’s function by using DDPG. The Communication Actor’s neural network is trained through gradients received from partner agents. An environment in which a cooperative multi-agent interaction is present was developed, computer simulation of the application of this method in the control problem of two robots pursuing two goals was carried out.

[Human-robot global Simulink modeling and analysis for an end-effector upper limb rehabilitation robot].

Science.gov (United States)

Liu, Yali; Ji, Linhong

2018-02-01

Robot rehabilitation has been a primary therapy method for the urgent rehabilitation demands of paralyzed patients after a stroke. The parameters in rehabilitation training such as the range of the training, which should be adjustable according to each participant's functional ability, are the key factors influencing the effectiveness of rehabilitation therapy. Therapists design rehabilitation projects based on the semiquantitative functional assessment scales and their experience. But these therapies based on therapists' experience cannot be implemented in robot rehabilitation therapy. This paper modeled the global human-robot by Simulink in order to analyze the relationship between the parameters in robot rehabilitation therapy and the patients' movement functional abilities. We compared the shoulder and elbow angles calculated by simulation with the angles recorded by motion capture system while the healthy subjects completed the simulated action. Results showed there was a remarkable correlation between the simulation data and the experiment data, which verified the validity of the human-robot global Simulink model. Besides, the relationship between the circle radius in the drawing tasks in robot rehabilitation training and the active movement degrees of shoulder as well as elbow was also matched by a linear, which also had a remarkable fitting coefficient. The matched linear can be a quantitative reference for the robot rehabilitation training parameters.

Efficient Modelling Methodology for Reconfigurable Underwater Robots

DEFF Research Database (Denmark)

Nielsen, Mikkel Cornelius; Blanke, Mogens; Schjølberg, Ingrid

2016-01-01

This paper considers the challenge of applying reconfigurable robots in an underwater environment. The main result presented is the development of a model for a system comprised of N, possibly heterogeneous, robots dynamically connected to each other and moving with 6 Degrees of Freedom (DOF). Th...

Sensor Fusion and Model Verification for a Mobile Robot

DEFF Research Database (Denmark)

Bisgaard, Morten; Vinther, Dennis; Østergaard, Kasper Zinck

2005-01-01

This paper presents the results of modeling, sensor fusion and model verification for a four-wheel driven, four-wheel steered mobile robot moving in outdoor terrain. The model derived for the robot describes the actuator and wheel dynamics and the vehicle kinematics, and includes friction terms...

Kinematics modeling and simulation of an autonomous omni-directional mobile robot

Directory of Open Access Journals (Sweden)

Daniel Garcia Sillas

2015-05-01

Full Text Available Although robotics has progressed to the extent that it has become relatively accessible with low-cost projects, there is still a need to create models that accurately represent the physical behavior of a robot. Creating a completely virtual platform allows us to test behavior algorithms such as those implemented using artificial intelligence, and additionally, it enables us to find potential problems in the physical design of the robot. The present work describes a methodology for the construction of a kinematic model and a simulation of the autonomous robot, specifically of an omni-directional wheeled robot. This paper presents the kinematic model development and its implementation using several tools. The result is a model that follows the kinematics of a triangular omni-directional mobile wheeled robot, which is then tested by using a 3D model imported from 3D Studio® and Matlab® for the simulation. The environment used for the experiment is very close to the real environment and reflects the kinematic characteristics of the robot.

Robots and the Limits of Morality

DEFF Research Database (Denmark)

Rodogno, Raffaele

2016-01-01

In this chapter, I ask whether we can coherently conceive of robots as moral agents and as moral patients. I answer both questions negatively but conditionally: for as long as robots lack certain features, they can be neither moral agents nor moral patients. These answers, of course, are not new...... and biological bases of moral practices and arguing that the relevant differences in such bases are sufficient, for the time being, to exclude robots from adopting, both, an active and a passive moral role....

Multi-physics modelling of a compliant humanoid robot

Energy Technology Data Exchange (ETDEWEB)

Zobova, Alexandra A., E-mail: azobova@mech.math.msu.su [Lomonosov Moscow State University, Faculty of Mechanics and Mathematics (Russian Federation); Habra, Timothée, E-mail: timothee.habra@uclouvain.be [Université catholique de Louvain (UCL), Center for Research in Mechatronics, Institute of Mechanics, Materials, and Civil Engineering (Belgium); Van der Noot, Nicolas, E-mail: nicolas.vandernoot@uclouvain.be, E-mail: nicolas.vandernoot@epfl.ch [EPFL STI IBI BIOROB, Biorobotics Laboratory, Institute of Bioengineering, École polytechnique fédérale de Lausanne (EPFL) (Switzerland); Dallali, Houman, E-mail: houman.dallali@iit.it; Tsagarakis, Nikolaos G., E-mail: nikos.tsagarakis@iit.it [Istituto Italiano di Tecnologia, Department of Advanced Robotics (Italy); Fisette, Paul, E-mail: paul.fisette@uclouvain.be; Ronsse, Renaud, E-mail: renaud.ronsse@uclouvain.be [Université catholique de Louvain (UCL), Center for Research in Mechatronics, Institute of Mechanics, Materials, and Civil Engineering (Belgium)

2017-01-15

We present a multibody simulator being used for compliant humanoid robot modelling and report our reasoning for choosing the settings of the simulator’s key features. First, we provide a study on how the numerical integration speed and accuracy depend on the coordinate representation of the multibody system. This choice is particularly critical for mechanisms with long serial chains (e.g. legs and arms). Our second contribution is a full electromechanical model of the inner dynamics of the compliant actuators embedded in the COMAN robot, since joints’ compliance is needed for the robot safety and energy efficiency. Third, we discuss the different approaches for modelling contacts and selecting an appropriate contact library. The recommended solution is to couple our simulator with an open-source contact library offering both accurate and fast contact modelling. The simulator performances are assessed by two different tasks involving contacts: a bimanual manipulation task and a squatting tasks. The former shows reliability of the simulator. For the latter, we report a comparison between the robot behaviour as predicted by our simulation environment, and the real one.

Multi-physics modelling of a compliant humanoid robot

International Nuclear Information System (INIS)

Zobova, Alexandra A.; Habra, Timothée; Van der Noot, Nicolas; Dallali, Houman; Tsagarakis, Nikolaos G.; Fisette, Paul; Ronsse, Renaud

2017-01-01

We present a multibody simulator being used for compliant humanoid robot modelling and report our reasoning for choosing the settings of the simulator’s key features. First, we provide a study on how the numerical integration speed and accuracy depend on the coordinate representation of the multibody system. This choice is particularly critical for mechanisms with long serial chains (e.g. legs and arms). Our second contribution is a full electromechanical model of the inner dynamics of the compliant actuators embedded in the COMAN robot, since joints’ compliance is needed for the robot safety and energy efficiency. Third, we discuss the different approaches for modelling contacts and selecting an appropriate contact library. The recommended solution is to couple our simulator with an open-source contact library offering both accurate and fast contact modelling. The simulator performances are assessed by two different tasks involving contacts: a bimanual manipulation task and a squatting tasks. The former shows reliability of the simulator. For the latter, we report a comparison between the robot behaviour as predicted by our simulation environment, and the real one.

Persuasive robotics : artificial embodied agents as persuasive technology

NARCIS (Netherlands)

Liu, C.; Ham, J.R.C.; Midden, C.J.H.

2011-01-01

• Social robots may provide a solution to many societal challenges. One of their core qualities must be the ability of effectively influencing human behavior or attitudes. • As a basis for strong influence, persuasive robots can take on the role of a social actor that can build a relationship with

Establishing an Improved Kane Dynamic Model for the 7-DOF Reconfigurable Modular Robot

Directory of Open Access Journals (Sweden)

Xiao Li

2017-01-01

Full Text Available We propose an improved Kane dynamic model theory for the 7-DOF modular robot in this paper, and the model precision is improved by the improved function T′it. We designed three types of progressive modular joints for reconfigurable modular robot that can be used in industrial robot, space robot, and special robot. The Kane dynamic model and the solid dynamic model are established, respectively, for the 7-DOF modular robot. After that, the experimental results are obtained from the simulation experiment of typical task in the established dynamic models. By the analysis model of error, the equation of the improved torque T′it is derived and proposed. And the improved Kane dynamic model is established for the modular robot that used T′it. Based on the experimental data, the undetermined coefficient matrix is five-order linear that was proved in 7-DOF modular robot. And the explicit formulation is solved of the Kane dynamic model and can be used in control system.

Research on Robot Pose Control Technology Based on Kinematics Analysis Model

Science.gov (United States)

Liu, Dalong; Xu, Lijuan

2018-01-01

In order to improve the attitude stability of the robot, proposes an attitude control method of robot based on kinematics analysis model, solve the robot walking posture transformation, grasping and controlling the motion planning problem of robot kinematics. In Cartesian space analytical model, using three axis accelerometer, magnetometer and the three axis gyroscope for the combination of attitude measurement, the gyroscope data from Calman filter, using the four element method for robot attitude angle, according to the centroid of the moving parts of the robot corresponding to obtain stability inertia parameters, using random sampling RRT motion planning method, accurate operation to any position control of space robot, to ensure the end effector along a prescribed trajectory the implementation of attitude control. The accurate positioning of the experiment is taken using MT-R robot as the research object, the test robot. The simulation results show that the proposed method has better robustness, and higher positioning accuracy, and it improves the reliability and safety of robot operation.

Modeling of Two-Wheeled Self-Balancing Robot Driven by DC Gearmotors

Science.gov (United States)

Frankovský, P.; Dominik, L.; Gmiterko, A.; Virgala, I.; Kurylo, P.; Perminova, O.

2017-08-01

This paper is aimed at modelling a two-wheeled self-balancing robot driven by the geared DC motors. A mathematical model consists of two main parts, the model of robot's mechanical structure and the model of the actuator. Linearized equations of motion are derived and the overall model of the two-wheeled self-balancing robot is represented in state-space realization for the purpose of state feedback controller design.

A cognitive robotic system based on the Soar cognitive architecture for mobile robot navigation, search, and mapping missions

Science.gov (United States)

Hanford, Scott D.

Most unmanned vehicles used for civilian and military applications are remotely operated or are designed for specific applications. As these vehicles are used to perform more difficult missions or a larger number of missions in remote environments, there will be a great need for these vehicles to behave intelligently and autonomously. Cognitive architectures, computer programs that define mechanisms that are important for modeling and generating domain-independent intelligent behavior, have the potential for generating intelligent and autonomous behavior in unmanned vehicles. The research described in this presentation explored the use of the Soar cognitive architecture for cognitive robotics. The Cognitive Robotic System (CRS) has been developed to integrate software systems for motor control and sensor processing with Soar for unmanned vehicle control. The CRS has been tested using two mobile robot missions: outdoor navigation and search in an indoor environment. The use of the CRS for the outdoor navigation mission demonstrated that a Soar agent could autonomously navigate to a specified location while avoiding obstacles, including cul-de-sacs, with only a minimal amount of knowledge about the environment. While most systems use information from maps or long-range perceptual capabilities to avoid cul-de-sacs, a Soar agent in the CRS was able to recognize when a simple approach to avoiding obstacles was unsuccessful and switch to a different strategy for avoiding complex obstacles. During the indoor search mission, the CRS autonomously and intelligently searches a building for an object of interest and common intersection types. While searching the building, the Soar agent builds a topological map of the environment using information about the intersections the CRS detects. The agent uses this topological model (along with Soar's reasoning, planning, and learning mechanisms) to make intelligent decisions about how to effectively search the building. Once the

Modeling and Simulation for Exploring Human-Robot Team Interaction Requirements

Energy Technology Data Exchange (ETDEWEB)

Dudenhoeffer, Donald Dean; Bruemmer, David Jonathon; Davis, Midge Lee

2001-12-01

Small-sized and micro-robots will soon be available for deployment in large-scale forces. Consequently, the ability of a human operator to coordinate and interact with largescale robotic forces is of great interest. This paper describes the ways in which modeling and simulation have been used to explore new possibilities for human-robot interaction. The paper also discusses how these explorations have fed implementation of a unified set of command and control concepts for robotic force deployment. Modeling and simulation can play a major role in fielding robot teams in actual missions. While live testing is preferred, limitations in terms of technology, cost, and time often prohibit extensive experimentation with physical multi-robot systems. Simulation provides insight, focuses efforts, eliminates large areas of the possible solution space, and increases the quality of actual testing.

The EMeRGE modular robot, an open platform for quick testing of evolved robot morphologies

DEFF Research Database (Denmark)

Moreno Garcia, Rodrigo; Liu, Ceyue; Faina, Andres

2017-01-01

This work presents the hardware design and implementation of the EMeRGE open modular robot platform. EMeRGE (Easy Modular Embodied Robot Generation) modules are designed to be cheap and easy to build and their hardware is open for anyone to use and modify. Four magnetic connectors enable the quick...... assembly of different complex robot morphologies like the ones generated by evolutionary robotics experiments. Non-human agents, like robotic manipulators, can also take advantage of the magnetic connectors to assemble and disassemble morphologies....

From pattern formation to material computation multi-agent modelling of physarum polycephalum

CERN Document Server

Jones, Jeff

2015-01-01

This book addresses topics of mobile multi-agent systems, pattern formation, biological modelling, artificial life, unconventional computation, and robotics. The behaviour of a simple organism which is capable of remarkable biological and computational feats that seem to transcend its simple component parts is examined and modelled. In this book the following question is asked: How can something as simple as Physarum polycephalum - a giant amoeboid single-celled organism which does not possess any neural tissue, fixed skeleton or organised musculature - can approximate complex computational behaviour during its foraging, growth and adaptation of its amorphous body plan, and with such limited resources? To answer this question the same apparent limitations as faced by the organism are applied: using only simple components with local interactions. A synthesis approach is adopted and a mobile multi-agent system with very simple individual behaviours is employed. It is shown their interactions yield emergent beha...

Behavioural domain knowledge transfer for autonomous agents

CSIR Research Space (South Africa)

Rosman, Benjamin S

2014-11-01

Full Text Available , and Behavior Transfer in Autonomous Robots, AAAI 2014 Fall Symposium Series, 13-15 November 2014 Behavioural Domain Knowledge Transfer for Autonomous Agents Benjamin Rosman Mobile Intelligent Autonomous Systems Modelling and Digital Science Council...

Experimental Robot Model Adjustments Based on Force–Torque Sensor Information

Directory of Open Access Journals (Sweden)

Santiago Martinez

2018-03-01

Full Text Available The computational complexity of humanoid robot balance control is reduced through the application of simplified kinematics and dynamics models. However, these simplifications lead to the introduction of errors that add to other inherent electro-mechanic inaccuracies and affect the robotic system. Linear control systems deal with these inaccuracies if they operate around a specific working point but are less precise if they do not. This work presents a model improvement based on the Linear Inverted Pendulum Model (LIPM to be applied in a non-linear control system. The aim is to minimize the control error and reduce robot oscillations for multiple working points. The new model, named the Dynamic LIPM (DLIPM, is used to plan the robot behavior with respect to changes in the balance status denoted by the zero moment point (ZMP. Thanks to the use of information from force–torque sensors, an experimental procedure has been applied to characterize the inaccuracies and introduce them into the new model. The experiments consist of balance perturbations similar to those of push-recovery trials, in which step-shaped ZMP variations are produced. The results show that the responses of the robot with respect to balance perturbations are more precise and the mechanical oscillations are reduced without comprising robot dynamics.

Spatial temporal patterns for action-oriented perception in roving robots

CERN Document Server

Patanè, Luca

2014-01-01

This book presents the result of a joint effort from different European Institutions within the framework of the EU funded project called SPARK II, devoted to device an insect brain computational model, useful to be embedded into autonomous robotic agents.  Part I reports the biological background on Drosophila melanogaster with particular attention to the main centers which are used as building blocks for the implementation of the insect brain computational model.  Part II  reports the mathematical approach to model the Central Pattern Generator used for the gait generation in a six-legged robot. Also the Reaction-diffusion principles in non-linear lattices are exploited to develop a compact internal representation of a dynamically changing environment for behavioral planning. In Part III  a software/hardware framework, developed to integrate the insect brain computational model in a simulated/real robotic platform, is illustrated. The different robots used for the experiments are also described.  Moreo...

Recognition of flow in everyday life using sensor agent robot with laser range finder

Science.gov (United States)

Goshima, Misa; Mita, Akira

2011-04-01

In the present paper, we suggest an algorithm for a sensor agent robot with a laser range finder to recognize the flows of residents in the living spaces in order to achieve flow recognition in the living spaces, recognition of the number of people in spaces, and the classification of the flows. House reform is or will be demanded to prolong the lifetime of the home. Adaption for the individuals is needed for our aging society which is growing at a rapid pace. Home autonomous mobile robots will become popular in the future for aged people to assist them in various situations. Therefore we have to collect various type of information of human and living spaces. However, a penetration in personal privacy must be avoided. It is essential to recognize flows in everyday life in order to assist house reforms and aging societies in terms of adaption for the individuals. With background subtraction, extra noise removal, and the clustering based k-means method, we got an average accuracy of more than 90% from the behavior from 1 to 3 persons, and also confirmed the reliability of our system no matter the position of the sensor. Our system can take advantages from autonomous mobile robots and protect the personal privacy. It hints at a generalization of flow recognition methods in the living spaces.

Virtual modeling of robot-assisted manipulations in abdominal surgery.

Science.gov (United States)

Berelavichus, Stanislav V; Karmazanovsky, Grigory G; Shirokov, Vadim S; Kubyshkin, Valeriy A; Kriger, Andrey G; Kondratyev, Evgeny V; Zakharova, Olga P

2012-06-27

To determine the effectiveness of using multidetector computed tomography (MDCT) data in preoperative planning of robot-assisted surgery. Fourteen patients indicated for surgery underwent MDCT using 64 and 256-slice MDCT. Before the examination, a specially constructed navigation net was placed on the patient's anterior abdominal wall. Processing of MDCT data was performed on a Brilliance Workspace 4 (Philips). Virtual vectors that imitate robotic and assistant ports were placed on the anterior abdominal wall of the 3D model of the patient, considering the individual anatomy of the patient and the technical capabilities of robotic arms. Sites for location of the ports were directed by projection on the roentgen-positive tags of the navigation net. There were no complications observed during surgery or in the post-operative period. We were able to reduce robotic arm interference during surgery. The surgical area was optimal for robotic and assistant manipulators without any need for reinstallation of the trocars. This method allows modeling of the main steps in robot-assisted intervention, optimizing operation of the manipulator and lowering the risk of injuries to internal organs.

Algorithms of walking and stability for an anthropomorphic robot

Science.gov (United States)

Sirazetdinov, R. T.; Devaev, V. M.; Nikitina, D. V.; Fadeev, A. Y.; Kamalov, A. R.

2017-09-01

Autonomous movement of an anthropomorphic robot is considered as a superposition of a set of typical elements of movement - so-called patterns, each of which can be considered as an agent of some multi-agent system [ 1 ]. To control the AP-601 robot, an information and communication infrastructure has been created that represents some multi-agent system that allows the development of algorithms for individual patterns of moving and run them in the system as a set of independently executed and interacting agents. The algorithms of lateral movement of the anthropomorphic robot AP-601 series with active stability due to the stability pattern are presented.

Ultra light inspection robotic arm, design and modeling

International Nuclear Information System (INIS)

Voisembert, S.

2012-01-01

One of the major challenges in robotics is the improvement of inspections operations in confined and hazardous area using unmanned remote handling systems. Articulated arm are used in this case to carry some diagnostic tools for the inspection tasks. These long reach multi-link carriers should be characterized by a large workspace and reduced mass. Today, with about ten degrees of freedom and ten meters long they have reached their performance limit. Indeed, for long reach, the arm should have enough torque to carry its own weight plus the payload in cantilever mode and enough stiffness to minimize the deflection caused by the gravity. Despite the use of best materials and components, this kind of robot has reach its performance limit. Overcoming this limit needs a change in paradigm. Therefore a problem-solving, analysis and forecasting tool TRIZ (theory of inventive problem solving) is used. It leads naturally to identify the origin of the dilemma: the proper weight of the arm and so its mass under gravity. In particular, it proposes to postulate that a no-mass robot exists. An analysis of the properties of such a robot leads to the patented concept of an ultra light inflatable robot with unique and constant volume and constant diameter joints. This new object would benefit from advantages such as easy implementation, harmlessness toward its environment and so the ability to lean on it without damage. Therefore it could easily increase its range and its foreseen low-cost building would open a wide field of new applications. This thesis work, elaborates appropriate technical concepts and dimensioning methods for ultra light inflatable robots. The payload and length performances of an inflatable robot are analytically validated. Experimentations and a finite-element modeling are used for a pre-dimensioning of the joints and different modes of construction are prototyped in partnership with, specialized company in thigh-tech textile. The joints are also modeled with

Fault-Tolerant Robot Programming through Simulation with Realistic Sensor Models

Directory of Open Access Journals (Sweden)

Axel Waggershauser

2008-11-01

Full Text Available We introduce a simulation system for mobile robots that allows a realistic interaction of multiple robots in a common environment. The simulated robots are closely modeled after robots from the EyeBot family and have an identical application programmer interface. The simulation supports driving commands at two levels of abstraction as well as numerous sensors such as shaft encoders, infrared distance sensors, and compass. Simulation of on-board digital cameras via synthetic images allows the use of image processing routines for robot control within the simulation. Specific error models for actuators, distance sensors, camera sensor, and wireless communication have been implemented. Progressively increasing error levels for an application program allows for testing and improving its robustness and fault-tolerance.

Detection of Subtle Context-Dependent Model Inaccuracies in High-Dimensional Robot Domains.

Science.gov (United States)

Mendoza, Juan Pablo; Simmons, Reid; Veloso, Manuela

2016-12-01

Autonomous robots often rely on models of their sensing and actions for intelligent decision making. However, when operating in unconstrained environments, the complexity of the world makes it infeasible to create models that are accurate in every situation. This article addresses the problem of using potentially large and high-dimensional sets of robot execution data to detect situations in which a robot model is inaccurate-that is, detecting context-dependent model inaccuracies in a high-dimensional context space. To find inaccuracies tractably, the robot conducts an informed search through low-dimensional projections of execution data to find parametric Regions of Inaccurate Modeling (RIMs). Empirical evidence from two robot domains shows that this approach significantly enhances the detection power of existing RIM-detection algorithms in high-dimensional spaces.

Intrinsically motivated reinforcement learning for human-robot interaction in the real-world.

Science.gov (United States)

Qureshi, Ahmed Hussain; Nakamura, Yutaka; Yoshikawa, Yuichiro; Ishiguro, Hiroshi

2018-03-26

For a natural social human-robot interaction, it is essential for a robot to learn the human-like social skills. However, learning such skills is notoriously hard due to the limited availability of direct instructions from people to teach a robot. In this paper, we propose an intrinsically motivated reinforcement learning framework in which an agent gets the intrinsic motivation-based rewards through the action-conditional predictive model. By using the proposed method, the robot learned the social skills from the human-robot interaction experiences gathered in the real uncontrolled environments. The results indicate that the robot not only acquired human-like social skills but also took more human-like decisions, on a test dataset, than a robot which received direct rewards for the task achievement. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ontological Reasoning for Human-Robot Teaming in Search and Rescue Missions

NARCIS (Netherlands)

Bagosi, T.; Hindriks, k.V.; Neerincx, M.A.

2016-01-01

In search and rescue missions robots are used to help rescue workers in exploring the disaster site. Our research focuses on how multiple robots and rescuers act as a team, and build up situation awareness. We propose a multi-agent system where each agent supports one member, either human or robot.

Artificial Intelligence techniques for mission planning for mobile robots

International Nuclear Information System (INIS)

Martinez, J.M.; Nomine, J.P.

1990-01-01

This work focuses on Spatial Modelization Techniques and on Control Software Architectures, in order to deal efficiently with the Navigation and Perception problems encountered in Mobile Autonomous Robotics. After a brief survey of the current various approaches for these techniques, we expose ongoing simulation works for a specific mission in robotics. Studies in progress used for Spatial Reasoning are based on new approaches combining Artificial Intelligence and Geometrical techniques. These methods deal with the problem of environment modelization using three types of models: geometrical topological and semantic models at different levels. The decision making processes of control are presented as the result of cooperation between a group of decentralized agents that communicate by sending messages. (author)

The mobile agent rendezvous problem in the ring

CERN Document Server

Kranakis, Evangelos; Marcou, Euripides

2010-01-01

Mobile agent computing is being used in fields as diverse as artificial intelligence, computational economics and robotics. Agents' ability to adapt dynamically and execute asynchronously and autonomously brings potential advantages in terms of fault-tolerance, flexibility and simplicity. This monograph focuses on studying mobile agents as modelled in distributed systems research and in particular within the framework of research performed in the distributed algorithms community. It studies the fundamental question of how to achieve rendezvous, the gathering of two or more agents at the same n

Plataforma autónoma inteligente para fútbol robot

Directory of Open Access Journals (Sweden)

Cesar Hernán Rodríguez Garavito

2008-01-01

Full Text Available This article presents the design, implementation, virtual simulation and test results for a hardware-software platform for robot soccer. The platform consists of a soccer field, a software-controlled mobile agent (AMC, a user-controlled mobile agent (MCU, a golf ball, an image sensor system and a path-planning controller. The problem for agent AMC is to sense the environment and move to a kicking position to score while avoiding opponents in its way. The soccer field is a bounded area of 1.5m x 2m in which mobile agents move following differential robot kinematics at 25.7cm/s speed; each robot has a kicking system which can speed up a golf ball at 1.43m/s velocity. A position sensor was implemented and optimised in three stages: capturing the soccer field image, converting to HSI format and applying digital filters and calculating the Cartesian components from colour patterns for identifying the mobile robots and the golf ball. Image sensor system processing speed is 30 frames per second. Robot path planning is controlled by a hybrid strategy based on two linearly combined fuzzy logic controllers; one takes agent AMC to the goal position and the other avoids obstacles while it moves to the goal position.

Soft computing in advanced robotics

CERN Document Server

Kobayashi, Ichiro; Kim, Euntai

2014-01-01

Intelligent system and robotics are inevitably bound up; intelligent robots makes embodiment of system integration by using the intelligent systems. We can figure out that intelligent systems are to cell units, while intelligent robots are to body components. The two technologies have been synchronized in progress. Making leverage of the robotics and intelligent systems, applications cover boundlessly the range from our daily life to space station; manufacturing, healthcare, environment, energy, education, personal assistance, logistics. This book aims at presenting the research results in relevance with intelligent robotics technology. We propose to researchers and practitioners some methods to advance the intelligent systems and apply them to advanced robotics technology. This book consists of 10 contributions that feature mobile robots, robot emotion, electric power steering, multi-agent, fuzzy visual navigation, adaptive network-based fuzzy inference system, swarm EKF localization and inspection robot. Th...

Proposed Robot Scheme with 5 DoF and Dynamic Modelling Using Maple Software

Directory of Open Access Journals (Sweden)

Shala Ahmet

2017-11-01

Full Text Available In this paper is represented Dynamical Modelling of robots which is commonly first important step of Modelling, Analysis and Control of robotic systems. This paper is focused on using Denavit-Hartenberg (DH convention for kinematics and Newton-Euler Formulations for dynamic modelling of 5 DoF - Degree of Freedom of 3D robot. The process of deriving of dynamical model is done using Software Maple. Derived Dynamical Model of 5 DoF robot is converted for Matlab use for future analysis, control and simulations.

Humanoid Walking Robot: Modeling, Inverse Dynamics, and Gain Scheduling Control

Directory of Open Access Journals (Sweden)

Elvedin Kljuno

2010-01-01

Full Text Available This article presents reference-model-based control design for a 10 degree-of-freedom bipedal walking robot, using nonlinear gain scheduling. The main goal is to show concentrated mass models can be used for prediction of the required joint torques for a bipedal walking robot. Relatively complicated architecture, high DOF, and balancing requirements make the control task of these robots difficult. Although linear control techniques can be used to control bipedal robots, nonlinear control is necessary for better performance. The emphasis of this work is to show that the reference model can be a bipedal walking model with concentrated mass at the center of gravity, which removes the problems related to design of a pseudo-inverse system. Another significance of this approach is the reduced calculation requirements due to the simplified procedure of nominal joint torques calculation. Kinematic and dynamic analysis is discussed including results for joint torques and ground force necessary to implement a prescribed walking motion. This analysis is accompanied by a comparison with experimental data. An inverse plant and a tracking error linearization-based controller design approach is described. We propose a novel combination of a nonlinear gain scheduling with a concentrated mass model for the MIMO bipedal robot system.

Synchronisation effects on the behavioural performance and information dynamics of a simulated minimally cognitive robotic agent.

Science.gov (United States)

Moioli, Renan C; Vargas, Patricia A; Husbands, Phil

2012-09-01

Oscillatory activity is ubiquitous in nervous systems, with solid evidence that synchronisation mechanisms underpin cognitive processes. Nevertheless, its informational content and relationship with behaviour are still to be fully understood. In addition, cognitive systems cannot be properly appreciated without taking into account brain-body- environment interactions. In this paper, we developed a model based on the Kuramoto Model of coupled phase oscillators to explore the role of neural synchronisation in the performance of a simulated robotic agent in two different minimally cognitive tasks. We show that there is a statistically significant difference in performance and evolvability depending on the synchronisation regime of the network. In both tasks, a combination of information flow and dynamical analyses show that networks with a definite, but not too strong, propensity for synchronisation are more able to reconfigure, to organise themselves functionally and to adapt to different behavioural conditions. The results highlight the asymmetry of information flow and its behavioural correspondence. Importantly, it also shows that neural synchronisation dynamics, when suitably flexible and reconfigurable, can generate minimally cognitive embodied behaviour.

Methodological Aspects of Modelling and Simulation of Robotized Workstations

Directory of Open Access Journals (Sweden)

Naqib Daneshjo

2018-05-01

Full Text Available From the point of view of development of application and program products, key directions that need to be respected in computer support for project activities are quite clearly specified. User interfaces with a high degree of graphical interactive convenience, two-dimensional and three-dimensional computer graphics contribute greatly to streamlining project methodologies and procedures in particular. This is mainly due to the fact that a high number of solved tasks is clearly graphic in the modern design of robotic systems. Automation of graphical character tasks is therefore a significant development direction for the subject area. The authors present results of their research in the area of automation and computer-aided design of robotized systems. A new methodical approach to modelling robotic workstations, consisting of ten steps incorporated into the four phases of the logistics process of creating and implementing a robotic workplace, is presented. The emphasis is placed on the modelling and simulation phase with verification of elaborated methodologies on specific projects or elements of the robotized welding plant in automotive production.

Designing interruptive behaviors of a public environmental monitoring robot

NARCIS (Netherlands)

Evers, V.; de Vries, R.; Alvito, P.

2011-01-01

This paper reports ongoing research to inform the design of a social robot to monitor levels of pollutant gasses in the air. Next to licensed environmental agents and immobile chemical sensors, mobile technologies such as robotic agents are needed to collect complaints and smell descriptions from

RoboSmith: Wireless Networked Architecture for Multiagent Robotic System

Directory of Open Access Journals (Sweden)

Florin Moldoveanu

2010-11-01

Full Text Available In this paper is presented an architecture for a flexible mini robot for a multiagent robotic system. In a multiagent system the value of an individual agent is negligible since the goal of the system is essential. Thus, the agents (robots need to be small, low cost and cooperative. RoboSmith are designed based on these conditions. The proposed architecture divide a robot into functional modules such as locomotion, control, sensors, communication, and actuation. Any mobile robot can be constructed by combining these functional modules for a specific application. An embedded software with dynamic task uploading and multi-tasking abilities is developed in order to create better interface between robots and the command center and among the robots. The dynamic task uploading allows the robots change their behaviors in runtime. The flexibility of the robots is given by facts that the robots can work in multiagent system, as master-slave, or hybrid mode, can be equipped with different modules and possibly be used in other applications such as mobile sensor networks remote sensing, and plant monitoring.

Multi-robot caravanning

KAUST Repository

Denny, Jory

2013-11-01

We study multi-robot caravanning, which is loosely defined as the problem of a heterogeneous team of robots visiting specific areas of an environment (waypoints) as a group. After formally defining this problem, we propose a novel solution that requires minimal communication and scales with the number of waypoints and robots. Our approach restricts explicit communication and coordination to occur only when robots reach waypoints, and relies on implicit coordination when moving between a given pair of waypoints. At the heart of our algorithm is the use of leader election to efficiently exploit the unique environmental knowledge available to each robot in order to plan paths for the group, which makes it general enough to work with robots that have heterogeneous representations of the environment. We implement our approach both in simulation and on a physical platform, and characterize the performance of the approach under various scenarios. We demonstrate that our approach can successfully be used to combine the planning capabilities of different agents. © 2013 IEEE.

Infant discrimination of humanoid robots

Directory of Open Access Journals (Sweden)

Goh eMatsuda

2015-09-01

Full Text Available Recently, extremely humanlike robots called androids have been developed, some of which are already being used in the field of entertainment. In the context of psychological studies, androids are expected to be used in the future as fully controllable human stimuli to investigate human nature. In this study, we used an android to examine infant discrimination ability between human beings and non-human agents. Participants (N = 42 infants were assigned to three groups based on their age, i.e., 6- to 8-month-olds, 9- to 11-month-olds, and 12- to 14-month-olds, and took part in a preferential looking paradigm. Of three types of agents involved in the paradigm—a human, an android modeled on the human, and a mechanical-looking robot made from the android—two at a time were presented side-by-side as they performed a grasping action. Infants’ looking behavior was measured using an eye tracking system, and the amount of time spent focusing on each of three areas of interest (face, goal, and body was analyzed. Results showed that all age groups predominantly looked at the robot and at the face area, and that infants aged over 9 months watched the goal area for longer than the body area. There was no difference in looking times and areas focused on between the human and the android. These findings suggest that 6- to 14-month-olds are unable to discriminate between the human and the android, although they can distinguish the mechanical robot from the human.

Embodying a cognitive model in a mobile robot

Science.gov (United States)

Benjamin, D. Paul; Lyons, Damian; Lonsdale, Deryle

2006-10-01

The ADAPT project is a collaboration of researchers in robotics, linguistics and artificial intelligence at three universities to create a cognitive architecture specifically designed to be embodied in a mobile robot. There are major respects in which existing cognitive architectures are inadequate for robot cognition. In particular, they lack support for true concurrency and for active perception. ADAPT addresses these deficiencies by modeling the world as a network of concurrent schemas, and modeling perception as problem solving. Schemas are represented using the RS (Robot Schemas) language, and are activated by spreading activation. RS provides a powerful language for distributed control of concurrent processes. Also, The formal semantics of RS provides the basis for the semantics of ADAPT's use of natural language. We have implemented the RS language in Soar, a mature cognitive architecture originally developed at CMU and used at a number of universities and companies. Soar's subgoaling and learning capabilities enable ADAPT to manage the complexity of its environment and to learn new schemas from experience. We describe the issues faced in developing an embodied cognitive architecture, and our implementation choices.

The HERA Approach To Morally Competent Robots

DEFF Research Database (Denmark)

Lindner, Felix; Bentzen, Martin Mose; Nebel, Bernhard

2017-01-01

for implementation in robots. The novelty is that HERA implements multiple ethical principles like utilitarianism, the principle of double effect, and a Pareto-inspired principle. These principles can be used to automatically assess moral situations represented in a format we call causal agency models. We discuss......To address the requirement for autonomous moral decision making, we introduce a software library for modeling hybrid ethical reasoning agents (short: HERA). The goal of the HERA project is to provide theoretically well-founded and practically usable logic-based machine ethics tools...... how to model moral situations using our approach, and how it can cope with uncertainty about moral values. Finally, we briefly outline the architecture of our robot IMMANUEL, which implements HERA and is able to explain ethical decisions to humans....

Combining robotic persuasive strategies : the persuasive power of a storytelling robot that uses gazing and gestures

NARCIS (Netherlands)

Ham, J.R.C.; Cuijpers, R.H.; Cabibihan, J.J.

Earlier theorizing suggested that an (artificial) agent that combines persuasive strategies will be more persuasive. Therefore, the current research investigated whether a robot that uses two persuasive strategies is more persuasive than a robot that uses only one. Two crucial persuasive strategies

Hybrid Analytical and Data-Driven Modeling for Feed-Forward Robot Control.

Science.gov (United States)

Reinhart, René Felix; Shareef, Zeeshan; Steil, Jochen Jakob

2017-02-08

Feed-forward model-based control relies on models of the controlled plant, e.g., in robotics on accurate knowledge of manipulator kinematics or dynamics. However, mechanical and analytical models do not capture all aspects of a plant's intrinsic properties and there remain unmodeled dynamics due to varying parameters, unmodeled friction or soft materials. In this context, machine learning is an alternative suitable technique to extract non-linear plant models from data. However, fully data-based models suffer from inaccuracies as well and are inefficient if they include learning of well known analytical models. This paper thus argues that feed-forward control based on hybrid models comprising an analytical model and a learned error model can significantly improve modeling accuracy. Hybrid modeling here serves the purpose to combine the best of the two modeling worlds. The hybrid modeling methodology is described and the approach is demonstrated for two typical problems in robotics, i.e., inverse kinematics control and computed torque control. The former is performed for a redundant soft robot and the latter for a rigid industrial robot with redundant degrees of freedom, where a complete analytical model is not available for any of the platforms.

FY1995 community support by mobile agents; 1995 nendo mobile agent ni yoru community keisei shien

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The purpose is to develop fundamental technologies for navigation systems and mobile computing systems in museums, theme parks and cities. Concretely, we implement software agents into the mobile computing environment which consists of PHS, mobile computers and mobile robots, and realize various functions to access regional information. We have studied on Communityware which supports human activities and communities by using mobile agents implemented into mobile computers and town robots. The mobile agents, which intelligently process information obtained in physical and virtual worlds, access regional information which is omnipresent in the environment. With respect to the approach using mobile computers, we have provided one hundred mobile computers in the international conference on multiagent systems 1996 and carried out the first experimentation of mobile computing in the world. The mobile computer has two functions: Community Viewer which displays interactions between members of communities and Social Matchmaker which supports to hold meetings by searching for people who have common interests. With respect to the approach using town robots, we have developed a robot system which can robustly behave in a complex outdoor environment by using vision agents embedded in the environment. The system aims at support of people in streets. (NEDO)

Modeling and Control of Collaborative Robot System using Haptic Feedback

Directory of Open Access Journals (Sweden)

Vivekananda Shanmuganatha

2017-08-01

Full Text Available When two robot systems can share understanding using any agreed knowledge, within the constraints of the system’s communication protocol, the approach may lead to a common improvement. This has persuaded numerous new research inquiries in human-robot collaboration. We have built up a framework prepared to do independent following and performing table-best protest object manipulation with humans and we have actualized two different activity models to trigger robot activities. The idea here is to explore collaborative systems and to build up a plan for them to work in a collaborative environment which has many benefits to a single more complex system. In the paper, two robots that cooperate among themselves are constructed. The participation linking the two robotic arms, the torque required and parameters are analyzed. Thus the purpose of this paper is to demonstrate a modular robot system which can serve as a base on aspects of robotics in collaborative robots using haptics.

Sensor Fusion Based Model for Collision Free Mobile Robot Navigation

Science.gov (United States)

Almasri, Marwah; Elleithy, Khaled; Alajlan, Abrar

2015-01-01

Autonomous mobile robots have become a very popular and interesting topic in the last decade. Each of them are equipped with various types of sensors such as GPS, camera, infrared and ultrasonic sensors. These sensors are used to observe the surrounding environment. However, these sensors sometimes fail and have inaccurate readings. Therefore, the integration of sensor fusion will help to solve this dilemma and enhance the overall performance. This paper presents a collision free mobile robot navigation based on the fuzzy logic fusion model. Eight distance sensors and a range finder camera are used for the collision avoidance approach where three ground sensors are used for the line or path following approach. The fuzzy system is composed of nine inputs which are the eight distance sensors and the camera, two outputs which are the left and right velocities of the mobile robot’s wheels, and 24 fuzzy rules for the robot’s movement. Webots Pro simulator is used for modeling the environment and the robot. The proposed methodology, which includes the collision avoidance based on fuzzy logic fusion model and line following robot, has been implemented and tested through simulation and real time experiments. Various scenarios have been presented with static and dynamic obstacles using one robot and two robots while avoiding obstacles in different shapes and sizes. PMID:26712766

Sensor Fusion Based Model for Collision Free Mobile Robot Navigation

Directory of Open Access Journals (Sweden)

Marwah Almasri

2015-12-01

Full Text Available Autonomous mobile robots have become a very popular and interesting topic in the last decade. Each of them are equipped with various types of sensors such as GPS, camera, infrared and ultrasonic sensors. These sensors are used to observe the surrounding environment. However, these sensors sometimes fail and have inaccurate readings. Therefore, the integration of sensor fusion will help to solve this dilemma and enhance the overall performance. This paper presents a collision free mobile robot navigation based on the fuzzy logic fusion model. Eight distance sensors and a range finder camera are used for the collision avoidance approach where three ground sensors are used for the line or path following approach. The fuzzy system is composed of nine inputs which are the eight distance sensors and the camera, two outputs which are the left and right velocities of the mobile robot’s wheels, and 24 fuzzy rules for the robot’s movement. Webots Pro simulator is used for modeling the environment and the robot. The proposed methodology, which includes the collision avoidance based on fuzzy logic fusion model and line following robot, has been implemented and tested through simulation and real time experiments. Various scenarios have been presented with static and dynamic obstacles using one robot and two robots while avoiding obstacles in different shapes and sizes.

Homeostasis control of building environment using sensor agent robot

Science.gov (United States)

Nagahama, Eri; Mita, Akira

2012-04-01

A human centered system for building is demanded to meet variety of needs due to the diversification and maturation of society. Smart buildings and smart houses have been studied to satisfy this demand. However, it is difficult for such systems to respond flexibly to unexpected events and needs that are caused by aging and complicate emotion changes. With this regards, we suggest "Biofied Buildings". The goal for this research is to realize buildings that are safer, more comfortable and more energy-efficient by embedding adaptive functions of life into buildings. In this paper, we propose a new control system for building environments, focused on physiological adaptation, particularly homeostasis, endocrine system and immune system. Residents are used as living sensors and controllers in the control loop. A sensor agent robot is used to acquire resident's discomfort feeling, and to output hormone-like signals to activate devices to control the environments. The proposed system could control many devices without establishing complicated scenarios. Results obtained from some simulations and the demonstration experiments using an LED lighting system showed that the proposed system were able to achieve robust and stable control of environments without complicated scenarios.

Dynamic Modelling of a CPG-Controlled Amphibious Biomimetic Swimming Robot

Directory of Open Access Journals (Sweden)

Rui Ding

2013-04-01

Full Text Available This paper focuses on the modelling and control problems of a self-propelled, multimodal amphibious robot. Inspired by the undulatory body motions of fish and dolphins, the amphibious robot propels itself underwater by oscillations of several modular fish-like propelling units coupled with a pair of pectoral fins capable of non-continuous 360 degree rotation. In order to mimic fish-like undulating propulsion, a control architecture based on Central Pattern Generator (CPG is applied to the amphibious robot for robust swimming gaits, including forward and backward swimming and turning, etc. With the simplification of the robot as a multi-link serial mechanism, a Lagrangian function is employed to establish the hydrodynamic model for steady swimming. The CPG motion control law is then imported into the Lagrangian-based dynamic model, where an associated system of kinematics and dynamics is formed to solve real-time movements and, further, to guide the exploration of the CPG parameters and steady locomotion gaits. Finally, comparative results between the simulations and experiments are provided to show the effectiveness of the built control models.

Robots Learn to Recognize Individuals from Imitative Encounters with People and Avatars

Science.gov (United States)

Boucenna, Sofiane; Cohen, David; Meltzoff, Andrew N.; Gaussier, Philippe; Chetouani, Mohamed

2016-02-01

Prior to language, human infants are prolific imitators. Developmental science grounds infant imitation in the neural coding of actions, and highlights the use of imitation for learning from and about people. Here, we used computational modeling and a robot implementation to explore the functional value of action imitation. We report 3 experiments using a mutual imitation task between robots, adults, typically developing children, and children with Autism Spectrum Disorder. We show that a particular learning architecture - specifically one combining artificial neural nets for (i) extraction of visual features, (ii) the robot’s motor internal state, (iii) posture recognition, and (iv) novelty detection - is able to learn from an interactive experience involving mutual imitation. This mutual imitation experience allowed the robot to recognize the interactive agent in a subsequent encounter. These experiments using robots as tools for modeling human cognitive development, based on developmental theory, confirm the promise of developmental robotics. Additionally, findings illustrate how person recognition may emerge through imitative experience, intercorporeal mapping, and statistical learning.

Planning and decision making for aerial robots

CERN Document Server

Bestaoui Sebbane, Yasmina

2014-01-01

This book provides an introduction to the emerging field of planning and decision making for aerial robots. An aerial robot is the ultimate form of Unmanned Aerial Vehicle, an aircraft endowed with built-in intelligence, requiring no direct human control and able to perform a specific task. It must be able to fly within a partially structured environment, to react and adapt to changing environmental conditions and to accommodate for the uncertainty that exists in the physical world. An aerial robot can be termed as a physical agent that exists and flies in the real 3D world, can sense its environment and act on it to achieve specific goals. So throughout this book, an aerial robot will also be termed as an agent.   Fundamental problems in aerial robotics include the tasks of spatial motion, spatial sensing and spatial reasoning. Reasoning in complex environments represents a difficult problem. The issues specific to spatial reasoning are planning and decision making. Planning deals with the trajectory algori...

Model identification and controller design of a fish-like robot

Science.gov (United States)

Ariyanto, Irfan; Kang, Taesam; Chan, Wai Leung; Lee, Youngjae

2007-04-01

Robotic fish is an interesting and prospective subject to develop. The simplest fish swimming mode to be mimicked for fish robots is the ostraciiform mode which only requires caudal fin flapping. An almost submerged ostraciiform fish robot was constructed to study its swimming characteristics. The swimming direction can be controlled by changing the mean angle of caudal fin oscillation. Experiments were conducted to study the behavior of the fish robot and in particular, the transfer function between swimming path angular rate and mean angle of the caudal fin oscillation were identified. Error to signal ratio quantity was used to determine how well the model fits with the experimental data. This identification model was used to design a 2-degree-of-freedom PID controller that meets some specific requirements to improve the steering performance.

Prototyping and Simulation of Robot Group Intelligence using Kohonen Networks.

Science.gov (United States)

Wang, Zhijun; Mirdamadi, Reza; Wang, Qing

2016-01-01

Intelligent agents such as robots can form ad hoc networks and replace human being in many dangerous scenarios such as a complicated disaster relief site. This project prototypes and builds a computer simulator to simulate robot kinetics, unsupervised learning using Kohonen networks, as well as group intelligence when an ad hoc network is formed. Each robot is modeled using an object with a simple set of attributes and methods that define its internal states and possible actions it may take under certain circumstances. As the result, simple, reliable, and affordable robots can be deployed to form the network. The simulator simulates a group of robots as an unsupervised learning unit and tests the learning results under scenarios with different complexities. The simulation results show that a group of robots could demonstrate highly collaborative behavior on a complex terrain. This study could potentially provide a software simulation platform for testing individual and group capability of robots before the design process and manufacturing of robots. Therefore, results of the project have the potential to reduce the cost and improve the efficiency of robot design and building.

Experimental Validation of a Dynamic Model for Lightweight Robots

Directory of Open Access Journals (Sweden)

Alessandro Gasparetto

2013-03-01

Full Text Available Nowadays, one of the main topics in robotics research is dynamic performance improvement by means of a lightening of the overall system structure. The effective motion and control of these lightweight robotic systems occurs with the use of suitable motion planning and control process. In order to do so, model-based approaches can be adopted by exploiting accurate dynamic models that take into account the inertial and elastic terms that are usually neglected in a heavy rigid link configuration. In this paper, an effective method for modelling spatial lightweight industrial robots based on an Equivalent Rigid Link System approach is considered from an experimental validation perspective. A dynamic simulator implementing the formulation is used and an experimental test-bench is set-up. Experimental tests are carried out with a benchmark L-shape mechanism.

Maintaining Limited-Range Connectivity Among Second-Order Agents

Science.gov (United States)

2016-07-07

we consider ad-hoc networks of robotic agents with double integrator dynamics. For such networks, the connectivity maintenance problems are: (i) do...connectivity-maintaining controls in a distributed fashion? The proposed solution is based on three contributions. First, we define and characterize...hoc networks of mobile autonomous agents. This loose ter- minology refers to groups of robotic agents with limited mobility and communica- tion

Mathematical model for adaptive control system of ASEA robot at Kennedy Space Center

Science.gov (United States)

Zia, Omar

1989-01-01

The dynamic properties and the mathematical model for the adaptive control of the robotic system presently under investigation at Robotic Application and Development Laboratory at Kennedy Space Center are discussed. NASA is currently investigating the use of robotic manipulators for mating and demating of fuel lines to the Space Shuttle Vehicle prior to launch. The Robotic system used as a testbed for this purpose is an ASEA IRB-90 industrial robot with adaptive control capabilities. The system was tested and it's performance with respect to stability was improved by using an analogue force controller. The objective of this research project is to determine the mathematical model of the system operating under force feedback control with varying dynamic internal perturbation in order to provide continuous stable operation under variable load conditions. A series of lumped parameter models are developed. The models include some effects of robot structural dynamics, sensor compliance, and workpiece dynamics.

A Social Cognitive Neuroscience Stance on Human-Robot Interactions

Directory of Open Access Journals (Sweden)

Chaminade Thierry

2011-12-01

Full Text Available Robotic devices, thanks to the controlled variations in their appearance and behaviors, provide useful tools to test hypotheses pertaining to social interactions. These agents were used to investigate one theoretical framework, resonance, which is defined, at the behavioral and neural levels, as an overlap between first- and third- person representations of mental states such as motor intentions or emotions. Behaviorally, we found a reduced, but significant, resonance towards a humanoid robot displaying biological motion, compared to a human. Using neuroimaging, we've reported that while perceptual processes in the human occipital and temporal lobe are more strongly engaged when perceiving a humanoid robot than a human action, activity in areas involved in motor resonance depends on attentional modulation for artificial agent more strongly than for human agents. Altogether, these studies using artificial agents offer valuable insights into the interaction of bottom-up and top-down processes in the perception of artificial agents.

Robotic and Virtual Reality BCIs Using Spatial Tactile and Auditory Oddball Paradigms.

Science.gov (United States)

Rutkowski, Tomasz M

2016-01-01

The paper reviews nine robotic and virtual reality (VR) brain-computer interface (BCI) projects developed by the author, in collaboration with his graduate students, within the BCI-lab research group during its association with University of Tsukuba, Japan. The nine novel approaches are discussed in applications to direct brain-robot and brain-virtual-reality-agent control interfaces using tactile and auditory BCI technologies. The BCI user intentions are decoded from the brainwaves in realtime using a non-invasive electroencephalography (EEG) and they are translated to a symbiotic robot or virtual reality agent thought-based only control. A communication protocol between the BCI output and the robot or the virtual environment is realized in a symbiotic communication scenario using an user datagram protocol (UDP), which constitutes an internet of things (IoT) control scenario. Results obtained from healthy users reproducing simple brain-robot and brain-virtual-agent control tasks in online experiments support the research goal of a possibility to interact with robotic devices and virtual reality agents using symbiotic thought-based BCI technologies. An offline BCI classification accuracy boosting method, using a previously proposed information geometry derived approach, is also discussed in order to further support the reviewed robotic and virtual reality thought-based control paradigms.

Robotic and Virtual Reality BCIs Using Spatial Tactile and Auditory Oddball Paradigms

Directory of Open Access Journals (Sweden)

Tomasz Maciej Rutkowski

2016-12-01

Full Text Available The paper reviews nine robotic and virtual reality (VR brain-computer interface (BCI projects developed by the author, in collaboration with his graduate students, within the BCI-lab research group during its association with University of Tsukuba, Japan. The nine novel approaches are discussed in applications to direct brain-robot and brain-virtual-reality-agent control interfaces using tactile and auditory BCI technologies. The BCI user intentions are decoded from the brainwaves in realtime using a non-invasive electroencephalography (EEG and they are translated to a symbiotic robot or virtual reality agent thought-based only control. A communication protocol between the BCI output and the robot or the virtual environment is realized in a symbiotic communication scenario using an user datagram protocol (UDP, which constitutes an internet of things (IoT control scenario. Results obtained from healthy users reproducing simple brain-robot and brain-virtual-agent control tasks in online experiments support the research goal of a possibility to interact with robotic devices and virtual reality agents using symbiotic thought-based BCI technologies. An offline BCI classification accuracy boosting method, using a previously proposed information geometry derived approach, is also discussed in order to further support the reviewed robotic and virtual reality thought-based control paradigms.

Self-Organization in Aggregating Robot Swarms: A DW-KNN Topological Approach

KAUST Repository

Khaldi, Belkacem

2018-02-02

In certain swarm applications, where the inter-agent distance is not the only factor in the collective behaviours of the swarm, additional properties such as density could have a crucial effect. In this paper, we propose applying a Distance-Weighted K-Nearest Neighbouring (DW-KNN) topology to the behaviour of robot swarms performing self-organized aggregation, in combination with a virtual physics approach to keep the robots together. A distance-weighted function based on a Smoothed Particle Hydrodynamic (SPH) interpolation approach, which is used to evaluate the robot density in the swarm, is applied as the key factor for identifying the K-nearest neighbours taken into account when aggregating the robots. The intra virtual physical connectivity among these neighbours is achieved using a virtual viscoelastic-based proximity model. With the ARGoS based-simulator, we model and evaluate the proposed approach, showing various self-organized aggregations performed by a swarm of N foot-bot robots. Also, we compared the aggregation quality of DW-KNN aggregation approach to that of the conventional KNN approach and found better performance.

Visual Trajectory-Tracking Model-Based Control for Mobile Robots

Directory of Open Access Journals (Sweden)

Andrej Zdešar

2013-09-01

Full Text Available In this paper we present a visual-control algorithm for driving a mobile robot along the reference trajectory. The configuration of the system consists of a two-wheeled differentially driven mobile robot that is observed by an overhead camera, which can be placed at arbitrary, but reasonable, inclination with respect to the ground plane. The controller must be capable of generating appropriate tangential and angular control velocities for the trajectory-tracking problem, based on the information received about the robot position obtained in the image. To be able to track the position of the robot through a sequence of images in real-time, the robot is marked with an artificial marker that can be distinguishably recognized by the image recognition subsystem. Using the property of differential flatness, a dynamic feedback compensator can be designed for the system, thereby extending the system into a linear form. The presented control algorithm for reference tracking combines a feedforward and a feedback loop, the structure also known as a two DOF control scheme. The feedforward part should drive the system to the vicinity of the reference trajectory and the feedback part should eliminate any errors that occur due to noise and other disturbances etc. The feedforward control can never achieve accurate reference following, but this deficiency can be eliminated with the introduction of the feedback loop. The design of the model predictive control is based on the linear error model. The model predictive control is given in analytical form, so the computational burden is kept at a reasonable level for real-time implementation. The control algorithm requires that a reference trajectory is at least twice differentiable function. A suitable approach to design such a trajectory is by exploiting some useful properties of the Bernstein-Bézier parametric curves. The simulation experiments as well as real system experiments on a robot normally used in the

Friendship with a robot: Children's perception of similarity between a robot's physical and virtual embodiment that supports diabetes self-management.

Science.gov (United States)

Sinoo, Claudia; van der Pal, Sylvia; Blanson Henkemans, Olivier A; Keizer, Anouk; Bierman, Bert P B; Looije, Rosemarijn; Neerincx, Mark A

2018-02-21

The PAL project develops a conversational agent with a physical (robot) and virtual (avatar) embodiment to support diabetes self-management of children ubiquitously. This paper assesses 1) the effect of perceived similarity between robot and avatar on children's' friendship towards the avatar, and 2) the effect of this friendship on usability of a self-management application containing the avatar (a) and children's motivation to play with it (b). During a four-day diabetes camp in the Netherlands, 21 children participated in interactions with both agent embodiments. Questionnaires measured perceived similarity, friendship, motivation to play with the app and its usability. Children felt stronger friendship towards the physical robot than towards the avatar. The more children perceived the robot and its avatar as the same agency, the stronger their friendship with the avatar was. The stronger their friendship with the avatar, the more they were motivated to play with the app and the higher the app scored on usability. The combination of physical and virtual embodiments seems to provide a unique opportunity for building ubiquitous long-term child-agent friendships. an avatar complementing a physical robot in health care could increase children's motivation and adherence to use self-management support systems. Copyright © 2018 Elsevier B.V. All rights reserved.

Modeling and analysis of a meso-hydraulic climbing robot with artificial muscle actuation.

Science.gov (United States)

Chapman, Edward M; Jenkins, Tyler E; Bryant, Matthew

2017-07-10

This paper presents a fully coupled electro-hydraulic model of a bio-inspired climbing robot actuated by fluidic artificial muscles (FAMs). This analysis expands upon previous FAM literature by considering not only the force and contraction characteristics of the actuator, but the complete hydraulic and electromechanical circuits as well as the dynamics of the climbing robot. This analysis allows modeling of the time-varying applied pressure, electrical current, and actuator contraction for accurate prediction of the robot motion, energy consumption, and mechanical work output. The developed model is first validated against mechanical and electrical data collected from a proof-of-concept prototype robot. The model is then employed to study the system-level sensitivities of the robot locomotion efficiency and average climbing speed to several design and operating parameters. The results of this analysis demonstrate that considering only the transduction efficiency of the FAM actuators is insufficient to maximize the efficiency of the complete robot, and that a holistic approach can lead to significant improvements in performance. © 2017 IOP Publishing Ltd.

Serpentine Robot Model and Gait Design Using Autodesk Inventor and Simulink SimMechanics

Science.gov (United States)

Daniel; Iman Alamsyah, Mohammad; Erwin; Tan, Sofyan

2014-03-01

The authors introduce gaits of a serpentine robot with linear expansion mechanism where the robot varies its length using joints with three degrees of freedom. The 3D model of the serpentine robot is drawed in Autocad Inventor® and exported to SimMechanics® for straighforward modeling of the kinematics. The gaits are important for robots designed to explore ruins of disasters where the working spaces are very tight. For maximum flexibility of the serpentine robot, we adopted a joint design with three parallel actuators, where the joint is capable of linear movement in the forward axis, and rotational movements around two other axes. The designed linear expansion gaits is calculated for forward movement when the robot is posing straight or turning laterally.

Serpentine Robot Model and Gait Design Using Autodesk Inventor and Simulink SimMechanics

Directory of Open Access Journals (Sweden)

Daniel

2014-03-01

Full Text Available The authors introduce gaits of a serpentine robot with linear expansion mechanism where the robot varies its length using joints with three degrees of freedom. The 3D model of the serpentine robot is drawed in Autocad Inventor® and exported to SimMechanics® for straighforward modeling of the kinematics. The gaits are important for robots designed to explore ruins of disasters where the working spaces are very tight. For maximum flexibility of the serpentine robot, we adopted a joint design with three parallel actuators, where the joint is capable of linear movement in the forward axis, and rotational movements around two other axes. The designed linear expansion gaits is calculated for forward movement when the robot is posing straight or turning laterally.

Modeling of Two-Wheeled Self-Balancing Robot Driven by DC Gearmotors

Directory of Open Access Journals (Sweden)

Frankovský P.

2017-08-01

Full Text Available This paper is aimed at modelling a two-wheeled self-balancing robot driven by the geared DC motors. A mathematical model consists of two main parts, the model of robot’s mechanical structure and the model of the actuator. Linearized equations of motion are derived and the overall model of the two-wheeled self-balancing robot is represented in state-space realization for the purpose of state feedback controller design.

RANA, a real-time multi-agent system simulator

DEFF Research Database (Denmark)

Jørgensen, Søren Vissing; Demazeau, Yves; Hallam, John

2016-01-01

for individualisation and abstraction while retaining efficiency. Events are managed by the C++ simulator core. Full run state can be recorded for post-processed visualisation or analysis. The new tool is demonstrated in three different cases: a mining robot simulation, which is purely action based; an agent......-based setup that is verifies the high precision exhibited by RANAs simulation core; and a state-based firefly-like agent simulation that models real-time responses to fellow agents' signals, in which event propagation and reception affect the result of the simulation....

Hybrid Analytical and Data-Driven Modeling for Feed-Forward Robot Control †

Directory of Open Access Journals (Sweden)

René Felix Reinhart

2017-02-01

Full Text Available Feed-forward model-based control relies on models of the controlled plant, e.g., in robotics on accurate knowledge of manipulator kinematics or dynamics. However, mechanical and analytical models do not capture all aspects of a plant’s intrinsic properties and there remain unmodeled dynamics due to varying parameters, unmodeled friction or soft materials. In this context, machine learning is an alternative suitable technique to extract non-linear plant models from data. However, fully data-based models suffer from inaccuracies as well and are inefficient if they include learning of well known analytical models. This paper thus argues that feed-forward control based on hybrid models comprising an analytical model and a learned error model can significantly improve modeling accuracy. Hybrid modeling here serves the purpose to combine the best of the two modeling worlds. The hybrid modeling methodology is described and the approach is demonstrated for two typical problems in robotics, i.e., inverse kinematics control and computed torque control. The former is performed for a redundant soft robot and the latter for a rigid industrial robot with redundant degrees of freedom, where a complete analytical model is not available for any of the platforms.

Hybrid Analytical and Data-Driven Modeling for Feed-Forward Robot Control †

Science.gov (United States)

Reinhart, René Felix; Shareef, Zeeshan; Steil, Jochen Jakob

2017-01-01

Feed-forward model-based control relies on models of the controlled plant, e.g., in robotics on accurate knowledge of manipulator kinematics or dynamics. However, mechanical and analytical models do not capture all aspects of a plant’s intrinsic properties and there remain unmodeled dynamics due to varying parameters, unmodeled friction or soft materials. In this context, machine learning is an alternative suitable technique to extract non-linear plant models from data. However, fully data-based models suffer from inaccuracies as well and are inefficient if they include learning of well known analytical models. This paper thus argues that feed-forward control based on hybrid models comprising an analytical model and a learned error model can significantly improve modeling accuracy. Hybrid modeling here serves the purpose to combine the best of the two modeling worlds. The hybrid modeling methodology is described and the approach is demonstrated for two typical problems in robotics, i.e., inverse kinematics control and computed torque control. The former is performed for a redundant soft robot and the latter for a rigid industrial robot with redundant degrees of freedom, where a complete analytical model is not available for any of the platforms. PMID:28208697

Collision Avoidance from Multiple Passive Agents with Partially Predictable Behavior

Directory of Open Access Journals (Sweden)

Khalil Muhammad Zuhaib

2017-09-01

Full Text Available Navigating a robot in a dynamic environment is a challenging task, especially when the behavior of other agents such as pedestrians, is only partially predictable. Also, the kinodynamic constraints on robot motion add an extra challenge. This paper proposes a novel navigational strategy for collision avoidance of a kinodynamically constrained robot from multiple moving passive agents with partially predictable behavior. Specifically, this paper presents a new approach to identify the set of control inputs to the robot, named control obstacle, which leads it towards a collision with a passive agent moving along an arbitrary path. The proposed method is developed by generalizing the concept of nonlinear velocity obstacle (NLVO, which is used to avoid collision with a passive agent, and takes into account the kinodynamic constraints on robot motion. Further, it formulates the navigational problem as an optimization problem, which allows the robot to make a safe decision in the presence of various sources of unmodelled uncertainties. Finally, the performance of the algorithm is evaluated for different parameters and is compared to existing velocity obstacle-based approaches. The simulated experiments show the excellent performance of the proposed approach in term of computation time and success rate.

The comparison of the use of holonic and agent-based methods in modelling of manufacturing systems

Science.gov (United States)

Foit, K.; Banaś, W.; Gwiazda, A.; Hryniewicz, P.

2017-08-01

The rapid evolution in the field of industrial automation and manufacturing is often called the 4th Industry Revolution. Worldwide availability of the internet access contributes to the competition between manufacturers, gives the opportunity for buying materials, parts and for creating the partnership networks, like cloud manufacturing, grid manufacturing (MGrid), virtual enterprises etc. The effect of the industry evolution is the need to search for new solutions in the field of manufacturing systems modelling and simulation. During the last decade researchers have developed the agent-based approach of modelling. This methodology have been taken from the computer science, but was adapted to the philosophy of industrial automation and robotization. The operation of the agent-based system depends on the simultaneous acting of different agents that may have different roles. On the other hand, there is the holon-based approach that uses the structures created by holons. It differs from the agent-based structure in some aspects, while the other ones are quite similar in both methodologies. The aim of this paper is to present the both methodologies and discuss the similarities and the differences. This may could help to select the optimal method of modelling, according to the considered problem and software resources.

DEVELOPING INDUSTRIAL ROBOT SIMULATION MODEL TUR10-K USING “UNIVERSAL MECHANISM” SOFTWARE COMPLEX

Directory of Open Access Journals (Sweden)

Vadim Vladimirovich Chirkov

2018-02-01

Full Text Available Manipulation robots are complex spatial mechanical systems having five or six degrees of freedom, and sometimes more. For this reason, modeling manipulative robots movement, even in the kinematic formulation, is a complex mathematical task. If one moves from kinematic modeling of motion to dynamic modeling then there must be taken into account the inertial properties of the modeling object. In this case, analytical constructing of such a complex object mathematical model as a manipulation robot becomes practically impossible. Therefore, special computer-aided design systems, called CAE-systems, are used for modeling complex mechanical systems. The purpose of the paper is simulation model construction of a complex mechanical system, such as the industrial robot TUR10-K, to obtain its dynamic characteristics. Developing such models makes it possible to reduce the complexity of designing complex systems process and to obtain the necessary characteristics. Purpose. Developing the simulation model of the industrial robot TUR10-K and obtaining dynamic characteristics of the mechanism. Methodology: the article is used a computer simulation method. Results: There is obtained the simulation model of the robot and its dynamic characteristics. Practical implications: the results can be used in the mechanical systems design and various simulation models.

Quantitative assessment of manual and robotic microcannulation for eye surgery using new eye model.

Science.gov (United States)

Tanaka, Shinichi; Harada, Kanako; Ida, Yoshiki; Tomita, Kyohei; Kato, Ippei; Arai, Fumihito; Ueta, Takashi; Noda, Yasuo; Sugita, Naohiko; Mitsuishi, Mamoru

2015-06-01

Microcannulation, a surgical procedure for the eye that requires drug injection into a 60-90 µm retinal vein, is difficult to perform manually. Robotic assistance has been proposed; however, its effectiveness in comparison to manual operation has not been quantified. An eye model has been developed to quantify the performance of manual and robotic microcannulation. The eye model, which is implemented with a force sensor and microchannels, also simulates the mechanical constraints of the instrument's movement. Ten subjects performed microcannulation using the model, with and without robotic assistance. The results showed that the robotic assistance was useful for motion stability when the drug was injected, whereas its positioning accuracy offered no advantage. An eye model was used to quantitatively assess the robotic microcannulation performance in comparison to manual operation. This approach could be valid for a better evaluation of surgical robotic assistance. Copyright © 2014 John Wiley & Sons, Ltd.

Why Are There Developmental Stages in Language Learning? A Developmental Robotics Model of Language Development.

Science.gov (United States)

Morse, Anthony F; Cangelosi, Angelo

2017-02-01

Most theories of learning would predict a gradual acquisition and refinement of skills as learning progresses, and while some highlight exponential growth, this fails to explain why natural cognitive development typically progresses in stages. Models that do span multiple developmental stages typically have parameters to "switch" between stages. We argue that by taking an embodied view, the interaction between learning mechanisms, the resulting behavior of the agent, and the opportunities for learning that the environment provides can account for the stage-wise development of cognitive abilities. We summarize work relevant to this hypothesis and suggest two simple mechanisms that account for some developmental transitions: neural readiness focuses on changes in the neural substrate resulting from ongoing learning, and perceptual readiness focuses on the perceptual requirements for learning new tasks. Previous work has demonstrated these mechanisms in replications of a wide variety of infant language experiments, spanning multiple developmental stages. Here we piece this work together as a single model of ongoing learning with no parameter changes at all. The model, an instance of the Epigenetic Robotics Architecture (Morse et al 2010) embodied on the iCub humanoid robot, exhibits ongoing multi-stage development while learning pre-linguistic and then basic language skills. Copyright © 2016 Cognitive Science Society, Inc.

Dynamical Behavior of Multi-Robot Systems Using Lattice Gas Automata

Energy Technology Data Exchange (ETDEWEB)

Cameron, S.M.; Robinett, R.; Stantz, K.M.; Trahan, M.W.; Wagner, J.S.

1999-03-11

Recent attention has been given to the deployment of an adaptable sensor array realized by multi-robotic systems. Our group has been studying the collective behavior of autonomous, multi-agent systems and their applications in the area of remote-sensing and emerging threats. To accomplish such tasks, an interdisciplinary research effort at Sandia National Laboratories are conducting tests in the fields of sensor technology, robotics, and multi-robotic and multi-agents architectures. Our goal is to coordinate a constellation of point sensors that optimizes spatial coverage and multivariate signal analysis using unmanned robotic vehicles (e.g., RATLERs, Robotic All-ten-sin Lunar Exploration Rover-class vehicles). Overall design methodology is to evolve complex collective behaviors realized through simple interaction (kinetic) physics and artificial intelligence to enable real-time operational responses to emerging threats. This paper focuses on our recent work understanding the dynamics of many-body systems using the physics-based hydrodynamic model of lattice gas automata. Three design features are investigated. One, for single-speed robots, a hexagonal nearest-neighbor interaction topology is necessary to preserve standard hydrodynamic flow. Two, adaptability, defined by the swarm's deformation rate, can be controlled through the hydrodynamic viscosity term, which, in turn, is defined by the local robotic interaction rules. Three, due to the inherent non-linearity of the dynamical equations describing large ensembles, development of stability criteria ensuring convergence to equilibrium states is developed by scaling information flow rates relative to a swarm's hydrodynamic flow rate. An initial test case simulates a swarm of twenty-five robots that maneuvers past an obstacle while following a moving target. A genetic algorithm optimizes applied nearest-neighbor forces in each of five spatial regions distributed over the simulation domain. Armed with

A proposal toward a possibilistic multi-robot task allocation

Energy Technology Data Exchange (ETDEWEB)

Guerrero, J.

2017-07-01

One of the main problems to solve in multi-agent (or multi-robot) systems is to select the best robot or group of robots to carry out a specific task. This problem, referenced as Multi-Agent (robot) task allocation (MRTA), is still an open issue in real environments. Swarm intelligence methods provide very simple solutions for the MRTA problem. One of the most widely used swarm methods are the so-called Response Threshold algorithms, where the behavior of the systems is modeled as a Markov chain and the robots in each time step select the next task to execute according to a transition probability function. Among other factors, this probability depends on a stimulus (for example the distance between the robot and the task). This classical probabilistic approach presents a lot of disadvantages:the transition function must meet constraints of a probabilistic distribution, the system only convergences to a stationary asymptotically, and so on. In order to overcome these problems, a new theoretical framework based on fuzzy (possibilistic) Markov chains was proposed [2]. As was proved, the possibilistic Markov chains outperform the classical probabilistic when a Max-Min algebra is considered for matrix composition. For example, fuzzy Markov chains convergence to a stable state in a finite number of steps 10 times faster than its probability counter part. Moreover, they improve the predictions of the system under imprecise information. Firstly, this paper will review relevant work in MRTA, from theoretical and experimental point of view. Then it will be summarized the aforementioned recent advances given toward a new possibilistic swarm multi-robot task allocation framework. It will be seen how the possibilistic Markov chains behave when other algebras are considered for matrix composition [1] and how the possibility transition function impacts on the system's performance [3]. Finally, it will be proposed new future works in this field. (Author)

A proposal toward a possibilistic multi-robot task allocation

International Nuclear Information System (INIS)

Guerrero, J.

2017-01-01

One of the main problems to solve in multi-agent (or multi-robot) systems is to select the best robot or group of robots to carry out a specific task. This problem, referenced as Multi-Agent (robot) task allocation (MRTA), is still an open issue in real environments. Swarm intelligence methods provide very simple solutions for the MRTA problem. One of the most widely used swarm methods are the so-called Response Threshold algorithms, where the behavior of the systems is modeled as a Markov chain and the robots in each time step select the next task to execute according to a transition probability function. Among other factors, this probability depends on a stimulus (for example the distance between the robot and the task). This classical probabilistic approach presents a lot of disadvantages:the transition function must meet constraints of a probabilistic distribution, the system only convergences to a stationary asymptotically, and so on. In order to overcome these problems, a new theoretical framework based on fuzzy (possibilistic) Markov chains was proposed [2]. As was proved, the possibilistic Markov chains outperform the classical probabilistic when a Max-Min algebra is considered for matrix composition. For example, fuzzy Markov chains convergence to a stable state in a finite number of steps 10 times faster than its probability counter part. Moreover, they improve the predictions of the system under imprecise information. Firstly, this paper will review relevant work in MRTA, from theoretical and experimental point of view. Then it will be summarized the aforementioned recent advances given toward a new possibilistic swarm multi-robot task allocation framework. It will be seen how the possibilistic Markov chains behave when other algebras are considered for matrix composition [1] and how the possibility transition function impacts on the system's performance [3]. Finally, it will be proposed new future works in this field. (Author)

An Interactive Tool for Creating Multi-Agent Systems and Interactive Agent-based Games

DEFF Research Database (Denmark)

Lund, Henrik Hautop; Pagliarini, Luigi

2011-01-01

Utilizing principles from parallel and distributed processing combined with inspiration from modular robotics, we developed the modular interactive tiles. As an educational tool, the modular interactive tiles facilitate the learning of multi-agent systems and interactive agent-based games...

The Dominant Robot: Threatening Robots Cause Psychological Reactance, Especially When They Have Incongruent Goals

Science.gov (United States)

Roubroeks, M. A. J.; Ham, J. R. C.; Midden, C. J. H.

Persuasive technology can take the form of a social agent that persuades people to change behavior or attitudes. However, like any persuasive technology, persuasive social agents might trigger psychological reactance, which can lead to restoration behavior. The current study investigated whether interacting with a persuasive robot can cause psychological reactance. Additionally, we investigated whether goal congruency plays a role in psychological reactance. Participants programmed a washing machine while a robot gave threatening advice. Confirming expectations, participants experienced more psychological reactance when receiving high-threatening advice compared to low-threatening advice. Moreover, when the robot gave high-threatening advice and expressed an incongruent goal, participants reported the highest level of psychological reactance (on an anger measure). Finally, high-threatening advice led to more restoration, and this relationship was partially mediated by psychological reactance. Overall, results imply that under certain circumstances persuasive technology can trigger opposite effects, especially when people have incongruent goal intentions.

Understanding the Uncanny: Both Atypical Features and Category Ambiguity Provoke Aversion toward Humanlike Robots.

Science.gov (United States)

Strait, Megan K; Floerke, Victoria A; Ju, Wendy; Maddox, Keith; Remedios, Jessica D; Jung, Malte F; Urry, Heather L

2017-01-01

Robots intended for social contexts are often designed with explicit humanlike attributes in order to facilitate their reception by (and communication with) people. However, observation of an "uncanny valley"-a phenomenon in which highly humanlike entities provoke aversion in human observers-has lead some to caution against this practice. Both of these contrasting perspectives on the anthropomorphic design of social robots find some support in empirical investigations to date. Yet, owing to outstanding empirical limitations and theoretical disputes, the uncanny valley and its implications for human-robot interaction remains poorly understood. We thus explored the relationship between human similarity and people's aversion toward humanlike robots via manipulation of the agents' appearances. To that end, we employed a picture-viewing task ( N agents = 60) to conduct an experimental test ( N participants = 72) of the uncanny valley's existence and the visual features that cause certain humanlike robots to be unnerving. Across the levels of human similarity, we further manipulated agent appearance on two dimensions, typicality (prototypic, atypical, and ambiguous) and agent identity (robot, person), and measured participants' aversion using both subjective and behavioral indices. Our findings were as follows: (1) Further substantiating its existence, the data show a clear and consistent uncanny valley in the current design space of humanoid robots. (2) Both category ambiguity, and more so, atypicalities provoke aversive responding, thus shedding light on the visual factors that drive people's discomfort. (3) Use of the Negative Attitudes toward Robots Scale did not reveal any significant relationships between people's pre-existing attitudes toward humanlike robots and their aversive responding-suggesting positive exposure and/or additional experience with robots is unlikely to affect the occurrence of an uncanny valley effect in humanoid robotics. This work furthers

Toward cognitive robotics

Science.gov (United States)

Laird, John E.

2009-05-01

Our long-term goal is to develop autonomous robotic systems that have the cognitive abilities of humans, including communication, coordination, adapting to novel situations, and learning through experience. Our approach rests on the recent integration of the Soar cognitive architecture with both virtual and physical robotic systems. Soar has been used to develop a wide variety of knowledge-rich agents for complex virtual environments, including distributed training environments and interactive computer games. For development and testing in robotic virtual environments, Soar interfaces to a variety of robotic simulators and a simple mobile robot. We have recently made significant extensions to Soar that add new memories and new non-symbolic reasoning to Soar's original symbolic processing, which should significantly improve Soar abilities for control of robots. These extensions include episodic memory, semantic memory, reinforcement learning, and mental imagery. Episodic memory and semantic memory support the learning and recalling of prior events and situations as well as facts about the world. Reinforcement learning provides the ability of the system to tune its procedural knowledge - knowledge about how to do things. Mental imagery supports the use of diagrammatic and visual representations that are critical to support spatial reasoning. We speculate on the future of unmanned systems and the need for cognitive robotics to support dynamic instruction and taskability.

Design, Modeling and Control of a Biped Line-Walking Robot

Directory of Open Access Journals (Sweden)

Ludan Wang

2010-12-01

Full Text Available The subject of this paper is the design and analysis of a biped line walking robot for inspection of power transmission lines. With a novel mechanism the centroid of the robot can be concentrated on the axis of hip joint to minimize the drive torque of the hip joint. The mechanical structure of the robot is discussed, as well as forward kinematics. Dynamic model is established in this paper to analyze the inverse kinematics for motion planning. The line-walking cycle of the line-walking robot is composed of a single-support phase and a double-support phase. Locomotion of the line-walking robot is discussed in details and the obstacle-navigation process is planed according to the structure of power transmission line. To fulfill the demands of line-walking, a control system and trajectories generation method are designed for the prototype of the line-walking robot. The feasibility of this concept is then confirmed by performing experiments with a simulated line environment.

Modelling of cooperating robotized systems with the use of object-based approach

Science.gov (United States)

Foit, K.; Gwiazda, A.; Banas, W.; Sekala, A.; Hryniewicz, P.

2015-11-01

Today's robotized manufacturing systems are characterized by high efficiency. The emphasis is placed mainly on the simultaneous work of machines. It could manifest in many ways, where the most spectacular one is the cooperation of several robots, during work on the same detail. What's more, recently a dual-arm robots are used that could mimic the manipulative skills of human hands. As a result, it is often hard to deal with the situation, when it is necessary not only to maintain sufficient precision, but also the coordination and proper sequence of movements of individual robots’ arms. The successful completion of this task depends on the individual robot control systems and their respective programmed, but also on the well-functioning communication between robot controllers. A major problem in case of cooperating robots is the possibility of collision between particular links of robots’ kinematic chains. This is not a simple case, because the manufacturers of robotic systems do not disclose the details of the control algorithms, then it is hard to determine such situation. Another problem with cooperation of robots is how to inform the other units about start or completion of part of the task, so that other robots can take further actions. This paper focuses on communication between cooperating robotic units, assuming that every robot is represented by object-based model. This problem requires developing a form of communication protocol that the objects can use for collecting the information about its environment. The approach presented in the paper is not limited to the robots and could be used in a wider range, for example during modelling of the complete workcell or production line.

Discrete time motion model for guiding people in urban areas using multiple robots

OpenAIRE

Garrell Zulueta, Anais; Sanfeliu Cortés, Alberto; Moreno-Noguer, Francesc

2009-01-01

We present a new model for people guidance in urban settings using several mobile robots, that overcomes the limitations of existing approaches, which are either tailored to tightly bounded environments, or based on unrealistic human behaviors. Although the robots motion is controlled by means of a standard particle filter formulation, the novelty of our approach resides in how the environment and human and robot motions are modeled. In particular we define a “Discrete-Time-Motion” model, whi...

Analysis of the type II robotic mixed-model assembly line balancing problem

Science.gov (United States)

Çil, Zeynel Abidin; Mete, Süleyman; Ağpak, Kürşad

2017-06-01

In recent years, there has been an increasing trend towards using robots in production systems. Robots are used in different areas such as packaging, transportation, loading/unloading and especially assembly lines. One important step in taking advantage of robots on the assembly line is considering them while balancing the line. On the other hand, market conditions have increased the importance of mixed-model assembly lines. Therefore, in this article, the robotic mixed-model assembly line balancing problem is studied. The aim of this study is to develop a new efficient heuristic algorithm based on beam search in order to minimize the sum of cycle times over all models. In addition, mathematical models of the problem are presented for comparison. The proposed heuristic is tested on benchmark problems and compared with the optimal solutions. The results show that the algorithm is very competitive and is a promising tool for further research.

Safe robot execution in model-based reinforcement learning

OpenAIRE

Martínez Martínez, David; Alenyà Ribas, Guillem; Torras, Carme

2015-01-01

Task learning in robotics requires repeatedly executing the same actions in different states to learn the model of the task. However, in real-world domains, there are usually sequences of actions that, if executed, may produce unrecoverable errors (e.g. breaking an object). Robots should avoid repeating such errors when learning, and thus explore the state space in a more intelligent way. This requires identifying dangerous action effects to avoid including such actions in the generated plans...

Dynamics of underwater legged locomotion: modeling and experiments on an octopus-inspired robot.

Science.gov (United States)

Calisti, M; Corucci, F; Arienti, A; Laschi, C

2015-07-30

This paper studies underwater legged locomotion (ULL) by means of a robotic octopus-inspired prototype and its associated model. Two different types of propulsive actions are embedded into the robot model: reaction forces due to leg contact with the ground and hydrodynamic forces such as the drag arising from the sculling motion of the legs. Dynamic parameters of the model are estimated by means of evolutionary techniques and subsequently the model is exploited to highlight some distinctive features of ULL. Specifically, the separation between the center of buoyancy (CoB)/center of mass and density affect the stability and speed of the robot, whereas the sculling movements contribute to propelling the robot even when its legs are detached from the ground. The relevance of these effects is demonstrated through robotic experiments and model simulations; moreover, by slightly changing the position of the CoB in the presence of the same feed-forward activation, a number of different behaviors (i.e. forward and backward locomotion at different speeds) are achieved.

Calibration of Robot Reference Frames for Enhanced Robot Positioning Accuracy

OpenAIRE

Cheng, Frank Shaopeng

2008-01-01

This chapter discussed the importance and methods of conducting robot workcell calibration for enhancing the accuracy of the robot TCP positions in industrial robot applications. It shows that the robot frame transformations define the robot geometric parameters such as joint position variables, link dimensions, and joint offsets in an industrial robot system. The D-H representation allows the robot designer to model the robot motion geometry with the four standard D-H parameters. The robot k...

Validation of multi-body modelling methodology for reconfigurable underwater robots

DEFF Research Database (Denmark)

Nielsen, M.C.; Eidsvik, O. A.; Blanke, Mogens

2016-01-01

This paper investigates the problem of employing reconfigurable robots in an underwater setting. The main results presented is the experimental validation of a modelling methodology for a system consisting of N dynamically connected robots with heterogeneous dynamics. Two distinct types...... of experiments are performed, a series of hydrostatic free-decay tests and a series of open-loop trajectory tests. The results are compared to a simulation based on the modelling methodology. The modelling methodology shows promising results for usage with systems composed of reconfigurable underwater modules...

Fairness in multi-agent systems

NARCIS (Netherlands)

Jong, de S.; Tuyls, K.P.; Verbeeck, K.

2008-01-01

Multi-agent systems are complex systems in which multiple autonomous entities, called agents, cooperate in order to achieve a common or personal goal. These entities may be computer software, robots, and also humans. In fact, many multi-agent systems are intended to operate in cooperation with or as

Cooperative Robot Localization Using Event-Triggered Estimation

Science.gov (United States)

Iglesias Echevarria, David I.

It is known that multiple robot systems that need to cooperate to perform certain activities or tasks incur in high energy costs that hinder their autonomous functioning and limit the benefits provided to humans by these kinds of platforms. This work presents a communications-based method for cooperative robot localization. Implementing concepts from event-triggered estimation, used with success in the field of wireless sensor networks but rarely to do robot localization, agents are able to only send measurements to their neighbors when the expected novelty in this information is high. Since all agents know the condition that triggers a measurement to be sent or not, the lack of a measurement is therefore informative and fused into state estimates. In the case agents do not receive either direct nor indirect measurements of all others, the agents employ a covariance intersection fusion rule in order to keep the local covariance error metric bounded. A comprehensive analysis of the proposed algorithm and its estimation performance in a variety of scenarios is performed, and the algorithm is compared to similar cooperative localization approaches. Extensive simulations are performed that illustrate the effectiveness of this method.

Econophysics of agent-based models

CERN Document Server

Aoyama, Hideaki; Chakrabarti, Bikas; Chakraborti, Anirban; Ghosh, Asim

2014-01-01

The primary goal of this book is to present the research findings and conclusions of physicists, economists, mathematicians and financial engineers working in the field of "Econophysics" who have undertaken agent-based modelling, comparison with empirical studies and related investigations. Most standard economic models assume the existence of the representative agent, who is “perfectly rational” and applies the utility maximization principle when taking action. One reason for this is the desire to keep models mathematically tractable: no tools are available to economists for solving non-linear models of heterogeneous adaptive agents without explicit optimization. In contrast, multi-agent models, which originated from statistical physics considerations, allow us to go beyond the prototype theories of traditional economics involving the representative agent. This book is based on the Econophys-Kolkata VII Workshop, at which many such modelling efforts were presented. In the book, leading researchers in the...

Developing and modeling of voice control system for prosthetic robot arm in medical systems

Directory of Open Access Journals (Sweden)

Koksal Gundogdu

2018-04-01

Full Text Available In parallel with the development of technology, various control methods are also developed. Voice control system is one of these control methods. In this study, an effective modelling upon mathematical models used in the literature is performed, and a voice control system is developed in order to control prosthetic robot arms. The developed control system has been applied on four-jointed RRRR robot arm. Implementation tests were performed on the designed system. As a result of the tests; it has been observed that the technique utilized in our system achieves about 11% more efficient voice recognition than currently used techniques in the literature. With the improved mathematical modelling, it has been shown that voice commands could be effectively used for controlling the prosthetic robot arm. Keywords: Voice recognition model, Voice control, Prosthetic robot arm, Robotic control, Forward kinematic

A review on modeling, identification and servo control of robotic ...

African Journals Online (AJOL)

user

This article reviews modeling, identification, and low level control of the robotic excavator. ... The oil viscosity, oil flow through the spool valves, and variable loading, ..... squares, to identify all the unknown individual parameters for a unmanned ..... Robust low level control of robotic excavation, PhD Thesis, The University of ...

The Making of a 3D-Printed, Cable-Driven, Single-Model, Lightweight Humanoid Robotic Hand

Directory of Open Access Journals (Sweden)

Li Tian

2017-12-01

Full Text Available Dexterity robotic hands can (Cummings, 1996 greatly enhance the functionality of humanoid robots, but the making of such hands with not only human-like appearance but also the capability of performing the natural movement of social robots is a challenging problem. The first challenge is to create the hand’s articulated structure and the second challenge is to actuate it to move like a human hand. A robotic hand for humanoid robot should look and behave human like. At the same time, it also needs to be light and cheap for widely used purposes. We start with studying the biomechanical features of a human hand and propose a simplified mechanical model of robotic hands, which can achieve the important local motions of the hand. Then, we use 3D modeling techniques to create a single interlocked hand model that integrates pin and ball joints to our hand model. Compared to other robotic hands, our design saves the time required for assembling and adjusting, which makes our robotic hand ready-to-use right after the 3D printing is completed. Finally, the actuation of the hand is realized by cables and motors. Based on this approach, we have designed a cost-effective, 3D printable, compact, and lightweight robotic hand. Our robotic hand weighs 150 g, has 15 joints, which are similar to a real human hand, and 6 Degree of Freedom (DOFs. It is actuated by only six small size actuators. The wrist connecting part is also integrated into the hand model and could be customized for different robots such as Nadine robot (Magnenat Thalmann et al., 2017. The compact servo bed can be hidden inside the Nadine robot’s sleeve and the whole robotic hand platform will not cause extra load to her arm as the total weight (150 g robotic hand and 162 g artificial skin is almost the same as her previous unarticulated robotic hand which is 348 g. The paper also shows our test results with and without silicon artificial hand skin, and on Nadine robot.

Human-Agent Teaming for Multi-Robot Control: A Literature Review

Science.gov (United States)

2013-02-01

advent of the Goggle driverless car , autonomous farm equipment, and unmanned commercial aircraft (Mosher, 2012). The inexorable trend towards...because a robot cannot be automated to navigate in difficult terrain. However, this high ratio will not be sustainable if large numbers of autonomous ...Parasuraman et al., 2007). 3.5 RoboLeader Past research indicates that autonomous cooperation between robots can improve the performance of the human

Investigating Ground Swarm Robotics Using Agent Based Simulation

National Research Council Canada - National Science Library

Ho, Sze-Tek T

2006-01-01

The concept of employing ground swarm robotics to accomplish tasks has been proposed for future use in humanitarian de-mining, plume monitoring, searching for survivors in a disaster site, and other hazardous activities...

A Study on Bipedal and Mobile Robot Behavior Through Modeling and Simulation

Directory of Open Access Journals (Sweden)

Nirmala Nirmala

2015-05-01

Full Text Available The purpose of this work is to study and analyze mobile robot behavior. In performing this, a framework is adopted and developed for mobile and bipedal robot. The robots are design, build, and run as proceed from the development of mechanical structure, electronics and control integration, and control software application. The behavior of those robots are difficult to be observed and analyzed qualitatively. To evaluate the design and behavior quality, modeling and simulation of robot structure and its task capability is performed. The stepwise procedure to robot behavior study is explained. Behavior cases study are experimented to bipedal robots, transporter robot and Autonomous Guided Vehicle (AGV developed at our institution. The experimentation are conducted on those robots by adjusting their dynamic properties and/or surrounding environment. Validation is performed by comparing the simulation result and the real robot execution. The simulation gives a more idealistic behavior execution rather than realistic one. Adjustments are performed to fine tuning simulation's parameters to provide a more realistic performance.

A Formation Behavior for Large-Scale Micro-Robot Deployment

Energy Technology Data Exchange (ETDEWEB)

Dudenhoeffer, Donald Dean; Jones, Michael Paul

2000-12-01

Micro-robots will soon be available for deployment by the thousands. Consequently, controlling and coordinating a force this large to accomplish a prescribed task is of great interest. This paper describes a flexible architecture for modeling thousands of autonomous agents simultaneously. The agents’ behavior is based on a subsumption architecture in which individual behaviors are prioritized with respect to all others. The primary behavior explored in this work is a group formation behavior based on social potential fields (Reif and Wang 1999). This paper extends the social potential field model by introducing a neutral zone within which other behaviors may exhibit themselves. Previous work with social potential fields has been restricted to models of “perfect” autonomous agents. The paper evaluates the effect of social potential fields in the presence of agent death (failure) and imperfect sensory input.

Design and Dynamic Model of a Frog-inspired Swimming Robot Powered by Pneumatic Muscles

Science.gov (United States)

Fan, Ji-Zhuang; Zhang, Wei; Kong, Peng-Cheng; Cai, He-Gao; Liu, Gang-Feng

2017-09-01

Pneumatic muscles with similar characteristics to biological muscles have been widely used in robots, and thus are promising drivers for frog inspired robots. However, the application and nonlinearity of the pneumatic system limit the advance. On the basis of the swimming mechanism of the frog, a frog-inspired robot based on pneumatic muscles is developed. To realize the independent tasks by the robot, a pneumatic system with internal chambers, micro air pump, and valves is implemented. The micro pump is used to maintain the pressure difference between the source and exhaust chambers. The pneumatic muscles are controlled by high-speed switch valves which can reduce the robot cost, volume, and mass. A dynamic model of the pneumatic system is established for the simulation to estimate the system, including the chamber, muscle, and pneumatic circuit models. The robot design is verified by the robot swimming experiments and the dynamic model is verified through the experiments and simulations of the pneumatic system. The simulation results are compared to analyze the functions of the source pressure, internal volume of the muscle, and circuit flow rate which is proved the main factor that limits the response of muscle pressure. The proposed research provides the application of the pneumatic muscles in the frog inspired robot and the pneumatic model to study muscle controller.

Empowerment As Replacement for the Three Laws of Robotics

Directory of Open Access Journals (Sweden)

Christoph Salge

2017-06-01

Full Text Available The greater ubiquity of robots creates a need for generic guidelines for robot behavior. We focus less on how a robot can technically achieve a predefined goal and more on what a robot should do in the first place. Particularly, we are interested in the question how a heuristic should look like, which motivates the robot’s behavior in interaction with human agents. We make a concrete, operational proposal as to how the information-theoretic concept of empowerment can be used as a generic heuristic to quantify concepts, such as self-preservation, protection of the human partner, and responding to human actions. While elsewhere we studied involved single-agent scenarios in detail, here, we present proof-of-principle scenarios demonstrating how empowerment interpreted in light of these perspectives allows one to specify core concepts with a similar aim as Asimov’s Three Laws of Robotics in an operational way. Importantly, this route does not depend on having to establish an explicit verbalized understanding of human language and conventions in the robots. Also, it incorporates the ability to take into account a rich variety of different situations and types of robotic embodiment.

Design and Optimization of Intelligent Service Robot Suspension System Using Dynamic Model

International Nuclear Information System (INIS)

Choi, Seong Hoon; Park, Tae Won; Lee, Soo Ho; Jung, Sung Pil; Jun, Kab Jin; Yoon, J. W.

2010-01-01

Recently, an intelligent service robot is being developed for use in guiding and providing information to visitors about the building at public institutions. The intelligent robot has a sensor at the bottom to recognize its location. Four wheels, which are arranged in the form of a lozenge, support the robot. This robot cannot be operated on uneven ground because its driving parts are attached to its main body that contains the important internal components. Continuous impact with the ground can change the precise positions of the components and weaken the connection between each structural part. In this paper, the design of the suspension system for such a robot is described. The dynamic model of the robot is created, and the driving characteristics of the robot with the designed suspension system are simulated. Additionally, the suspension system is optimized to reduce the impact for the robot components

What makes a robot 'social'?

Science.gov (United States)

Jones, Raya A

2017-08-01

Rhetorical moves that construct humanoid robots as social agents disclose tensions at the intersection of science and technology studies (STS) and social robotics. The discourse of robotics often constructs robots that are like us (and therefore unlike dumb artefacts). In the discourse of STS, descriptions of how people assimilate robots into their activities are presented directly or indirectly against the backdrop of actor-network theory, which prompts attributing agency to mundane artefacts. In contradistinction to both social robotics and STS, it is suggested here that to view a capacity to partake in dialogical action (to have a 'voice') is necessary for regarding an artefact as authentically social. The theme is explored partly through a critical reinterpretation of an episode that Morana Alač reported and analysed towards demonstrating her bodies-in-interaction concept. This paper turns to 'body' with particular reference to Gibsonian affordances theory so as to identify the level of analysis at which dialogicality enters social interactions.

Hierarchical Kinematic Modelling and Optimal Design of a Novel Hexapod Robot with Integrated Limb Mechanism

Directory of Open Access Journals (Sweden)

Guiyang Xin

2015-09-01

Full Text Available This paper presents a novel hexapod robot, hereafter named PH-Robot, with three degrees of freedom (3-DOF parallel leg mechanisms based on the concept of an integrated limb mechanism (ILM for the integration of legged locomotion and arm manipulation. The kinematic model plays an important role in the parametric optimal design and motion planning of robots. However, models of parallel mechanisms are often difficult to obtain because of the implicit relationship between the motions of actuated joints and the motion of a moving platform. In order to derive the kinematic equations of the proposed hexapod robot, an extended hierarchical kinematic modelling method is proposed. According to the kinematic model, the geometrical parameters of the leg are optimized utilizing a comprehensive objective function that considers both dexterity and payload. PH-Robot has distinct advantages in accuracy and load ability over a robot with serial leg mechanisms through the former's comparison of performance indices. The reachable workspace of the leg verifies its ability to walk and manipulate. The results of the trajectory tracking experiment demonstrate the correctness of the kinematic model of the hexapod robot.

Robotic phrenic nerve harvest: a feasibility study in a pig model.

Science.gov (United States)

Porto de Melo, P; Miyamoto, H; Serradori, T; Ruggiero Mantovani, G; Selber, J; Facca, S; Xu, W-D; Santelmo, N; Liverneaux, P

2014-10-01

The aim of this study was to report on the feasibility of robotic phrenic nerve harvest in a pig model. A surgical robot (Da Vinci S™ system, Intuitive Surgical(®), Sunnyvale, CA) was installed with three ports on the pig's left chest. The phrenic nerve was transected distally where it enters the diaphragm. The phrenic nerve harvest was successfully performed in 45 minutes without major complications. The advantages of robotic microsurgery for phrenic nerve harvest are the motion scaling up to 5 times, elimination of physiological tremor, and free movement of joint-equipped robotic arms. Robot-assisted neurolysis may be clinically useful for harvesting the phrenic nerve for brachial plexus reconstruction. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

Modeling of robotic fish propelled by an ionic polymer-metal composite caudal fin

Science.gov (United States)

Chen, Zheng; Shatara, Stephan; Tan, Xiaobo

2009-03-01

In this paper, a model is proposed for a biomimetic robotic fish propelled by an ionic polymer metal composite (IPMC) actuator with a rigid passive fin at the end. The model incorporates both IPMC actuation dynamics and the hydrodynamics, and predicts the steady-state speed of the robot under a periodic actuation voltage. Experimental results have shown that the proposed model can predict the fish motion for different tail dimensions. Since its parameters are expressed in terms of physical properties and geometric dimensions, the model is expected to be instrumental in optimal design of the robotic fish.

MODELADO, SIMULACIÓN Y CONTROL DEL ROBOT PARA CIRUGÍA LAPAROSCÓPICA 'LAPBOT' MODELING, SIMULATION AND CONTROL OF SURGICAL LAPAROSCOPIC ROBOT 'LAPBOT'

Directory of Open Access Journals (Sweden)

Sergio Alexander Salinas

2009-12-01

Full Text Available Este artículo presenta el modelado matemático y estructural, la simulación por computador y el control por par calculado del robot para cirugía laparoscópica ‘LapBot’, que ha sido desarrollado en el Grupo de Investigación de Automática Industrial de la Universidad del Cauca, Colombia. Inicialmente se muestra un resumen de los principales robots utilizados como asistentes para cirugías de laparoscopia en el mundo, y de cómo tratan ellos el problema del paso por la incisión practicada en la cavidad abdominal. Con base en lo anterior se describen los requerimientos que deben cumplir los robots de este tipo y a partir de éstos se diseña el robot LapBot. Se muestra el modelo cinemático y dinámico del robot LapBot, así como el modelo de la restricción espacial que representa el punto de incisión abdominal. Se implementa una estrategia de control basada en el modelo del robot (control por par calculado. Diversas trayectorias en un plano y en un espacio de tres dimensiones son utilizadas para validar tanto el modelo como el controlador.This paper presents the mathematical and structural model, simulation and computed torque control of the LapBot robot, developed by the Group of Investigation of Industrial Automatics, of the University of Cauca, Colombia. First, a summary of the principal surgery assistant robots of the world is presented, and how they solve the problem of passing through the incision into the abdominal cavity. Based on this, the conditions that must be fulfilled by the robots of this type is exposed, and from these conditions the LapBot robot is designed. Its kinematics and dynamics model is shown, as well as the mathematical spatial restriction that incision represents. A control strategy based on the model (computed torque control is implemented. Several trajectories defined in a plane and in a three dimensions space are used to validate the model and the control.

What do care robots reveal about technology?

NARCIS (Netherlands)

op den Akker, Hendrikus J.A.

2015-01-01

Ethical issues raised by the idea of social robots that care point at a fundamental difference between man and machine. What sort of “difference‿ is this? We propose a semiotic view on technology to clarify the relations users have with social robots. Are these autonomous agents just promising or

Self-Imitation and Environmental Scaffolding for Robot Teaching

Directory of Open Access Journals (Sweden)

Joe Saunders

2007-03-01

Full Text Available Imitative learning and learning by observation are social mechanisms that allow a robot to acquire knowledge from a human or another robot. However to be able to obtain skills in this way the robot faces many complex issues, one of which is that of finding solutions to the correspondence problem. Evolutionary predecessors to observational imitation may have been self-imitation where an agent avoids the complexities of the correspondence problem by learning and replicating actions it has experienced through the manipulation of its body. We investigate how a robotic control and teaching system using self-imitation can be constructed with reference to psychological models of motor control and ideas from social scaffolding seen in animals. Within these scaffolded environments sets of competencies can be built by constructing hierarchical state/action memory maps of the robot's interaction within that environment. The scaffolding process provides a mechanism to enable learning to be scaled up. The resulting system allows a human trainer to teach a robot new skills and modify skills that the robot may possess. Additionally the system allows the robot to notify the trainer when it is being taught skills it already has in its repertoire and to direct and focus its attention and sensor resources to relevant parts of the skill being executed. We argue that these mechanisms may be a first step towards the transformation from self-imitation to observational imitation. The system is validated on a physical pioneer robot that is taught using self-imitation to track, follow and point to a patterned object.

Self-imitation and Environmental Scaffolding for Robot Teaching

Directory of Open Access Journals (Sweden)

Chrystopher L. Nehaniv

2008-11-01

Full Text Available Imitative learning and learning by observation are social mechanisms that allow a robot to acquire knowledge from a human or another robot. However to be able to obtain skills in this way the robot faces many complex issues, one of which is that of finding solutions to the correspondence problem. Evolutionary predecessors to observational imitation may have been self-imitation where an agent avoids the complexities of the correspondence problem by learning and replicating actions it has experienced through the manipulation of its body. We investigate how a robotic control and teaching system using self-imitation can be constructed with reference to psychological models of motor control and ideas from social scaffolding seen in animals. Within these scaffolded environments sets of competencies can be built by constructing hierarchical state/action memory maps of the robot's interaction within that environment. The scaffolding process provides a mechanism to enable learning to be scaled up. The resulting system allows a human trainer to teach a robot new skills and modify skills that the robot may possess. Additionally the system allows the robot to notify the trainer when it is being taught skills it already has in its repertoire and to direct and focus its attention and sensor resources to relevant parts of the skill being executed. We argue that these mechanisms may be a first step towards the transformation from self-imitation to observational imitation. The system is validated on a physical pioneer robot that is taught using self-imitation to track, follow and point to a patterned object.

Robotic assessment of neuromuscular characteristics using musculoskeletal models: A pilot study.

Science.gov (United States)

Jayaneththi, V R; Viloria, J; Wiedemann, L G; Jarrett, C; McDaid, A J

2017-07-01

Non-invasive neuromuscular characterization aims to provide greater insight into the effectiveness of existing and emerging rehabilitation therapies by quantifying neuromuscular characteristics relating to force production, muscle viscoelasticity and voluntary neural activation. In this paper, we propose a novel approach to evaluate neuromuscular characteristics, such as muscle fiber stiffness and viscosity, by combining robotic and HD-sEMG measurements with computational musculoskeletal modeling. This pilot study investigates the efficacy of this approach on a healthy population and provides new insight on potential limitations of conventional musculoskeletal models for this application. Subject-specific neuromuscular characteristics of the biceps and triceps brachii were evaluated using robot-measured kinetics, kinematics and EMG activity as inputs to a musculoskeletal model. Repeatability experiments in five participants revealed large variability within each subjects evaluated characteristics, with almost all experiencing variation greater than 50% of full scale when repeating the same task. The use of robotics and HD-sEMG, in conjunction with musculoskeletal modeling, to quantify neuromuscular characteristics has been explored. Despite the ability to predict joint kinematics with relatively high accuracy, parameter characterization was inconsistent i.e. many parameter combinations gave rise to minimal kinematic error. The proposed technique is a novel approach for in vivo neuromuscular characterization and is a step towards the realization of objective in-home robot-assisted rehabilitation. Importantly, the results have confirmed the technical (robot and HD-sEMG) feasibility while highlighting the need to develop new musculoskeletal models and optimization techniques capable of achieving consistent results across a range of dynamic tasks. Copyright © 2017 Elsevier Ltd. All rights reserved.

Object as a model of intelligent robot in the virtual workspace

Science.gov (United States)

Foit, K.; Gwiazda, A.; Banas, W.; Sekala, A.; Hryniewicz, P.

2015-11-01

The contemporary industry requires that every element of a production line will fit into the global schema, which is connected with the global structure of business. There is the need to find the practical and effective ways of the design and management of the production process. The term “effective” should be understood in a manner that there exists a method, which allows building a system of nodes and relations in order to describe the role of the particular machine in the production process. Among all the machines involved in the manufacturing process, industrial robots are the most complex ones. This complexity is reflected in the realization of elaborated tasks, involving handling, transporting or orienting the objects in a work space, and even performing simple machining processes, such as deburring, grinding, painting, applying adhesives and sealants etc. The robot also performs some activities connected with automatic tool changing and operating the equipment mounted on the wrist of the robot. Because of having the programmable control system, the robot also performs additional activities connected with sensors, vision systems, operating the storages of manipulated objects, tools or grippers, measuring stands, etc. For this reason the description of the robot as a part of production system should take into account the specific nature of this machine: the robot is a substitute of a worker, who performs his tasks in a particular environment. In this case, the model should be able to characterize the essence of "employment" in the sufficient way. One of the possible approaches to this problem is to treat the robot as an object, in the sense often used in computer science. This allows both: to describe certain operations performed on the object, as well as describing the operations performed by the object. This paper focuses mainly on the definition of the object as the model of the robot. This model is confronted with the other possible descriptions. The

Object as a model of intelligent robot in the virtual workspace

International Nuclear Information System (INIS)

Foit, K; Gwiazda, A; Banas, W; Sekala, A; Hryniewicz, P

2015-01-01

The contemporary industry requires that every element of a production line will fit into the global schema, which is connected with the global structure of business. There is the need to find the practical and effective ways of the design and management of the production process. The term “effective” should be understood in a manner that there exists a method, which allows building a system of nodes and relations in order to describe the role of the particular machine in the production process. Among all the machines involved in the manufacturing process, industrial robots are the most complex ones. This complexity is reflected in the realization of elaborated tasks, involving handling, transporting or orienting the objects in a work space, and even performing simple machining processes, such as deburring, grinding, painting, applying adhesives and sealants etc. The robot also performs some activities connected with automatic tool changing and operating the equipment mounted on the wrist of the robot. Because of having the programmable control system, the robot also performs additional activities connected with sensors, vision systems, operating the storages of manipulated objects, tools or grippers, measuring stands, etc. For this reason the description of the robot as a part of production system should take into account the specific nature of this machine: the robot is a substitute of a worker, who performs his tasks in a particular environment. In this case, the model should be able to characterize the essence of 'employment' in the sufficient way. One of the possible approaches to this problem is to treat the robot as an object, in the sense often used in computer science. This allows both: to describe certain operations performed on the object, as well as describing the operations performed by the object. This paper focuses mainly on the definition of the object as the model of the robot. This model is confronted with the other possible

Dynamic modelling of a 3-CPU parallel robot via screw theory

Directory of Open Access Journals (Sweden)

L. Carbonari

2013-04-01

Full Text Available The article describes the dynamic modelling of I.Ca.Ro., a novel Cartesian parallel robot recently designed and prototyped by the robotics research group of the Polytechnic University of Marche. By means of screw theory and virtual work principle, a computationally efficient model has been built, with the final aim of realising advanced model based controllers. Then a dynamic analysis has been performed in order to point out possible model simplifications that could lead to a more efficient run time implementation.

Dynamic modeling and optimal joint torque coordination of advanced robotic systems

Science.gov (United States)

Kang, Hee-Jun

The development is documented of an efficient dynamic modeling algorithm and the subsequent optimal joint input load coordination of advanced robotic systems for industrial application. A closed-form dynamic modeling algorithm for the general closed-chain robotic linkage systems is presented. The algorithm is based on the transfer of system dependence from a set of open chain Lagrangian coordinates to any desired system generalized coordinate set of the closed-chain. Three different techniques for evaluation of the kinematic closed chain constraints allow the representation of the dynamic modeling parameters in terms of system generalized coordinates and have no restriction with regard to kinematic redundancy. The total computational requirement of the closed-chain system model is largely dependent on the computation required for the dynamic model of an open kinematic chain. In order to improve computational efficiency, modification of an existing open-chain KIC based dynamic formulation is made by the introduction of the generalized augmented body concept. This algorithm allows a 44 pct. computational saving over the current optimized one (O(N4), 5995 when N = 6). As means of resolving redundancies in advanced robotic systems, local joint torque optimization is applied for effectively using actuator power while avoiding joint torque limits. The stability problem in local joint torque optimization schemes is eliminated by using fictitious dissipating forces which act in the necessary null space. The performance index representing the global torque norm is shown to be satisfactory. In addition, the resulting joint motion trajectory becomes conservative, after a transient stage, for repetitive cyclic end-effector trajectories. The effectiveness of the null space damping method is shown. The modular robot, which is built of well defined structural modules from a finite-size inventory and is controlled by one general computer system, is another class of evolving

Smart: sistemas multi-agente robótico

Directory of Open Access Journals (Sweden)

JOVANI ALBERTO JIMÉNEZ BUILES

2008-01-01

Full Text Available El siguiente artículo busca dar una visión global de los Sistemas Multi-Agentes Robóticos (MARS mediante una explicación de las áreas relacionadas con el tema para luego presentar el Sistema Multi-Agente Robótico (SMART. SMART es un enjambre inteligente conformado por un robot nodriza y tres robot tipo baliza (guías que navegan de manera colaborativa un escenario estructurado.

Evolving self-assembly in autonomous homogeneous robots: experiments with two physical robots.

Science.gov (United States)

Ampatzis, Christos; Tuci, Elio; Trianni, Vito; Christensen, Anders Lyhne; Dorigo, Marco

2009-01-01

This research work illustrates an approach to the design of controllers for self-assembling robots in which the self-assembly is initiated and regulated by perceptual cues that are brought forth by the physical robots through their dynamical interactions. More specifically, we present a homogeneous control system that can achieve assembly between two modules (two fully autonomous robots) of a mobile self-reconfigurable system without a priori introduced behavioral or morphological heterogeneities. The controllers are dynamic neural networks evolved in simulation that directly control all the actuators of the two robots. The neurocontrollers cause the dynamic specialization of the robots by allocating roles between them based solely on their interaction. We show that the best evolved controller proves to be successful when tested on a real hardware platform, the swarm-bot. The performance achieved is similar to the one achieved by existing modular or behavior-based approaches, also due to the effect of an emergent recovery mechanism that was neither explicitly rewarded by the fitness function, nor observed during the evolutionary simulation. Our results suggest that direct access to the orientations or intentions of the other agents is not a necessary condition for robot coordination: Our robots coordinate without direct or explicit communication, contrary to what is assumed by most research works in collective robotics. This work also contributes to strengthening the evidence that evolutionary robotics is a design methodology that can tackle real-world tasks demanding fine sensory-motor coordination.

Robotic kidney autotransplantation in a porcine model: a procedure-specific training platform for the simulation of robotic intracorporeal vascular anastomosis.

Science.gov (United States)

Tiong, Ho Yee; Goh, Benjamin Yen Seow; Chiong, Edmund; Tan, Lincoln Guan Lim; Vathsala, Anatharaman

2018-03-31

Robotic-assisted kidney transplantation (RKT) with the Da Vinci (Intuitive, USA) platform has been recently developed to improve outcomes by decreasing surgical site complications and morbidity, especially in obese patients. This potential paradigm shift in the surgical technique of kidney transplantation is performed in only a few centers. For wider adoption of this high stake complex operation, we aimed to develop a procedure-specific simulation platform in a porcine model for the training of robotic intracorporeal vascular anastomosis and evaluating vascular anastomoses patency. This paper describes the requirements and steps developed for the above training purpose. Over a series of four animal ethics' approved experiments, the technique of robotic-assisted laparoscopic autotransplantation of the kidney was developed in Amsterdam live pigs (60-70 kg). The surgery was based around the vascular anastomosis technique described by Menon et al. This non-survival porcine training model is targeted at transplant surgeons with robotic surgery experience. Under general anesthesia, each pig was placed in lateral decubitus position with the placement of one robotic camera port, two robotic 8 mm ports and one assistant port. Robotic docking over the pig posteriorly was performed. The training platform involved the following procedural steps. First, ipsilateral iliac vessel dissection was performed. Second, robotic-assisted laparoscopic donor nephrectomy was performed with in situ perfusion of the kidney with cold Hartmann's solution prior to complete division of the hilar vessels, ureter and kidney mobilization. Thirdly, the kidney was either kept in situ for orthotopic autotransplantation or mobilized to the pelvis and orientated for the vascular anastomosis, which was performed end to end or end to side after vessel loop clamping of the iliac vessels, respectively, using 6/0 Gore-Tex sutures. Following autotransplantation and release of vessel loops, perfusion of the

Modelling and Control of the Multi-Stage Cable Pulley-Driven Flexible-Joint Robot

Directory of Open Access Journals (Sweden)

Phongsaen Pitakwatchara

2014-07-01

Full Text Available This work is concerned with the task space impedance control of a robot driven through a multi-stage nonlinear flexible transmission system. Specifically, a two degrees-of-freedom cable pulley-driven flexible-joint robot is considered. Realistic modelling of the system is developed within the bond graph modelling framework. The model captures the nonlinear compliance behaviour of the multi-stage cable pulley transmission system, the spring effect of the augmented counterbalancing mechanism, the major loss throughout the system elements, and the typical inertial dynamics of the robot. Next, a task space impedance controller based on limited information about the angle and the current of the motors is designed. The motor current is used to infer the transmitted torque, by which the motor inertia may be modulated. The motor angle is employed to estimate the stationary distal robot link angle and the robot joint velocity. They are used in the controller to generate the desired damping force and to shape the potential energy of the flexible joint robot system to the desired configuration. Simulation and experimental results of the controlled system signify the competency of the proposed control law.

Smart Agents and Sentiment in the Heterogeneous Agent Model

Czech Academy of Sciences Publication Activity Database

Vácha, Lukáš; Baruník, Jozef; Vošvrda, Miloslav

2009-01-01

Roč. 18, č. 3 (2009), s. 209-219 ISSN 1210-0455 R&D Projects: GA MŠk(CZ) LC06075; GA ČR GP402/08/P207; GA ČR(CZ) GA402/09/0965 Institutional research plan: CEZ:AV0Z10750506 Keywords : heterogeneous agent model * market structure * smart traders * Hurst exponent Subject RIV: AH - Economics http://library.utia.cas.cz/separaty/2009/E/vacha- smart agent s and sentiment in the heterogeneous agent model.pdf

Effects of Robot Facial Characteristics and Gender in Persuasive Human-Robot Interaction

Directory of Open Access Journals (Sweden)

Aimi S. Ghazali

2018-06-01

Full Text Available The growing interest in social robotics makes it relevant to examine the potential of robots as persuasive agents and, more specifically, to examine how robot characteristics influence the way people experience such interactions and comply with the persuasive attempts by robots. The purpose of this research is to identify how the (ostensible gender and the facial characteristics of a robot influence the extent to which people trust it and the psychological reactance they experience from its persuasive attempts. This paper reports a laboratory study where SociBot™, a robot capable of displaying different faces and dynamic social cues, delivered persuasive messages to participants while playing a game. In-game choice behavior was logged, and trust and reactance toward the advisor were measured using questionnaires. Results show that a robotic advisor with upturned eyebrows and lips (features that people tend to trust more in humans is more persuasive, evokes more trust, and less psychological reactance compared to one displaying eyebrows pointing down and lips curled downwards at the edges (facial characteristics typically not trusted in humans. Gender of the robot did not affect trust, but participants experienced higher psychological reactance when interacting with a robot of the opposite gender. Remarkably, mediation analysis showed that liking of the robot fully mediates the influence of facial characteristics on trusting beliefs and psychological reactance. Also, psychological reactance was a strong and reliable predictor of trusting beliefs but not of trusting behavior. These results suggest robots that are intended to influence human behavior should be designed to have facial characteristics we trust in humans and could be personalized to have the same gender as the user. Furthermore, personalization and adaptation techniques designed to make people like the robot more may help ensure they will also trust the robot.

Understanding and Resolving Failures in Human-Robot Interaction: Literature Review and Model Development

Directory of Open Access Journals (Sweden)

Shanee Honig

2018-06-01

Full Text Available While substantial effort has been invested in making robots more reliable, experience demonstrates that robots operating in unstructured environments are often challenged by frequent failures. Despite this, robots have not yet reached a level of design that allows effective management of faulty or unexpected behavior by untrained users. To understand why this may be the case, an in-depth literature review was done to explore when people perceive and resolve robot failures, how robots communicate failure, how failures influence people's perceptions and feelings toward robots, and how these effects can be mitigated. Fifty-two studies were identified relating to communicating failures and their causes, the influence of failures on human-robot interaction (HRI, and mitigating failures. Since little research has been done on these topics within the HRI community, insights from the fields of human computer interaction (HCI, human factors engineering, cognitive engineering and experimental psychology are presented and discussed. Based on the literature, we developed a model of information processing for robotic failures (Robot Failure Human Information Processing, RF-HIP, that guides the discussion of our findings. The model describes the way people perceive, process, and act on failures in human robot interaction. The model includes three main parts: (1 communicating failures, (2 perception and comprehension of failures, and (3 solving failures. Each part contains several stages, all influenced by contextual considerations and mitigation strategies. Several gaps in the literature have become evident as a result of this evaluation. More focus has been given to technical failures than interaction failures. Few studies focused on human errors, on communicating failures, or the cognitive, psychological, and social determinants that impact the design of mitigation strategies. By providing the stages of human information processing, RF-HIP can be used as a

A Grammatical Approach to the Modeling of an Autonomous Robot

Directory of Open Access Journals (Sweden)

Gabriel López-García

2012-06-01

Full Text Available Virtual Worlds Generator is a grammatical model that is proposed to define virtual worlds. It integrates the diversity of sensors and interaction devices, multimodality and a virtual simulation system. Its grammar allows the definition and abstraction in symbols strings of the scenes of the virtual world, independently of the hardware that is used to represent the world or to interact with it. A case study is presented to explain how to use the proposed model to formalize a robot navigation system with multimodal perception and a hybrid control scheme of the robot. The result is an instance of the model grammar that implements the robotic system and is independent of the sensing devices used for perception and interaction. As a conclusion the Virtual Worlds Generator adds value in the simulation of virtual worlds since the definition can be done formally and independently of the peculiarities of the supporting devices

Model Reduction of a Flexible-Joint Robot: A Port-Hamitonian Approach

NARCIS (Netherlands)

Jardón Kojakhmetov, Hildeberto; Muñoz Arias, Mauricio; Scherpen, Jacquelien M.A.

2016-01-01

In this paper we explore the methodology of model order reduction based on singular perturbations for a flexible-joint robot within the port-Hamiltonian framework. We show that a flexible-joint robot has a port-Hamiltonian representation which is also a singularly perturbed ordinary differential

Model-Based Design and Evaluation of a Brachiating Monkey Robot with an Active Waist

Directory of Open Access Journals (Sweden)

Alex Kai-Yuan Lo

2017-09-01

Full Text Available We report on the model-based development of a monkey robot that is capable of performing continuous brachiation locomotion on swingable rod, as the intermediate step toward studying brachiation on the soft rope or on horizontal ropes with both ends fixed. The work is different from other previous works where the model or the robot swings on fixed bars. The model, which is composed of two rigid links, was inspired by the dynamic motion of primates. The model further served as the design guideline for a robot that has five degree of freedoms: two on each arm for rod changing and one on the waist to initiate a swing motion. The model was quantitatively formulated, and its dynamic behavior was analyzed in simulation. Further, a two-stage controller was developed within the simulation environment, where the first stage used the natural dynamics of a two-link pendulum-like model, and the second stage used the angular velocity feedback to regulate the waist motion. Finally, the robot was empirically built and evaluated. The experimental results confirm that the robot can perform model-like swing behavior and continuous brachiation locomotion on rods.

Easy Reconfiguration of Modular Industrial Collaborative Robots

DEFF Research Database (Denmark)

Schou, Casper

2016-01-01

the production staff collaborating to perform common tasks. This change of environment imposes a much more dynamic lifecycle for the robot which consequently requires new ways of interacting. This thesis investigates how the changeover to a new task on a collaborative robot can be performed by the shop floor...... operators already working alongside the robot. To effectively perform this changeover, the operator must both reconfigure the hardware of the robot and reprogram the robot to match the new task. To enable shop floor operators to quickly and intuitively program the robot, this thesis proposes the use...... of parametric, task-related robot skills with a manual parameterization method. Reconfiguring the hardware entails adding, removing, or modifying some of the robot’s components. This thesis investigate how software configurator tools can aid the operator in selecting appropriate hardware modules, and how agent...

The Hybrid Ethical Reasoning Agent IMMANUEL

DEFF Research Database (Denmark)

Bentzen, Martin Mose; Linder, Felix

We introduce a novel software library that supportsthe implementation of hybrid ethical reasoning agents (HERA).The objective is to make moral principles available to robotprogramming. At its current stage, HERA can assess the moralpermissibility of actions using the principle of double effect......, andit can make utilitarian judgments.We present the prototype robotIMMANUEL based on HERA. The robot will be used to conductresearch on joint moral reasoning in human-robot interaction....

Dynamic modelling and simulation for control of a cylindrical robotic manipulator

International Nuclear Information System (INIS)

Iqbal, A.; Athar, S.M.

1995-03-01

In this report a dynamic model for the three degrees-of-freedom cylindrical manipulator, INFOMATE has been developed. Although the robot dynamics are highly coupled and non-linear, the developed model is relatively straight forward and compact for control engineering and simulation applications. The model has been simulated using the graphical simulation package SIMULINK. Different aspects of INFOMATE associated with forward dynamics, inverse dynamics and control have been investigated by performing various simulation experiments. These simulation experiments confirm the accuracy and applicability of the dynamic robot model. (author) 18 figs

Understanding Human Hand Gestures for Learning Robot Pick-and-Place Tasks

Directory of Open Access Journals (Sweden)

Hsien-I Lin

2015-05-01

Full Text Available Programming robots by human demonstration is an intuitive approach, especially by gestures. Because robot pick-and-place tasks are widely used in industrial factories, this paper proposes a framework to learn robot pick-and-place tasks by understanding human hand gestures. The proposed framework is composed of the module of gesture recognition and the module of robot behaviour control. For the module of gesture recognition, transport empty (TE, transport loaded (TL, grasp (G, and release (RL from Gilbreth's therbligs are the hand gestures to be recognized. A convolution neural network (CNN is adopted to recognize these gestures from a camera image. To achieve the robust performance, the skin model by a Gaussian mixture model (GMM is used to filter out non-skin colours of an image, and the calibration of position and orientation is applied to obtain the neutral hand pose before the training and testing of the CNN. For the module of robot behaviour control, the corresponding robot motion primitives to TE, TL, G, and RL, respectively, are implemented in the robot. To manage the primitives in the robot system, a behaviour-based programming platform based on the Extensible Agent Behavior Specification Language (XABSL is adopted. Because the XABSL provides the flexibility and re-usability of the robot primitives, the hand motion sequence from the module of gesture recognition can be easily used in the XABSL programming platform to implement the robot pick-and-place tasks. The experimental evaluation of seven subjects performing seven hand gestures showed that the average recognition rate was 95.96%. Moreover, by the XABSL programming platform, the experiment showed the cube-stacking task was easily programmed by human demonstration.

Agent-based modeling and network dynamics

CERN Document Server

Namatame, Akira

2016-01-01

The book integrates agent-based modeling and network science. It is divided into three parts, namely, foundations, primary dynamics on and of social networks, and applications. The book begins with the network origin of agent-based models, known as cellular automata, and introduce a number of classic models, such as Schelling’s segregation model and Axelrod’s spatial game. The essence of the foundation part is the network-based agent-based models in which agents follow network-based decision rules. Under the influence of the substantial progress in network science in late 1990s, these models have been extended from using lattices into using small-world networks, scale-free networks, etc. The book also shows that the modern network science mainly driven by game-theorists and sociophysicists has inspired agent-based social scientists to develop alternative formation algorithms, known as agent-based social networks. The book reviews a number of pioneering and representative models in this family. Upon the gi...

Toward Shared Working Space of Human and Robotic Agents Through Dipole Flow Field for Dependable Path Planning.

Science.gov (United States)

Trinh, Lan Anh; Ekström, Mikael; Cürüklü, Baran

2018-01-01

Recent industrial developments in autonomous systems, or agents, which assume that humans and the agents share the same space or even work in close proximity, open for new challenges in robotics, especially in motion planning and control. In these settings, the control system should be able to provide these agents a reliable path following control when they are working in a group or in collaboration with one or several humans in complex and dynamic environments. In such scenarios, these agents are not only moving to reach their goals, i.e., locations, they are also aware of the movements of other entities to find a collision-free path. Thus, this paper proposes a dependable, i.e., safe, reliable and effective, path planning algorithm for a group of agents that share their working space with humans. Firstly, the method employs the Theta * algorithm to initialize the paths from a starting point to a goal for a set of agents. As Theta * algorithm is computationally heavy, it only reruns when there is a significant change of the environment. To deal with the movements of the agents, a static flow field along the configured path is defined. This field is used by the agents to navigate and reach their goals even if the planned trajectories are changed. Secondly, a dipole field is calculated to avoid the collision of agents with other agents and human subjects. In this approach, each agent is assumed to be a source of a magnetic dipole field in which the magnetic moment is aligned with the moving direction of the agent. The magnetic dipole-dipole interactions between these agents generate repulsive forces to help them to avoid collision. The effectiveness of the proposed approach has been evaluated with extensive simulations. The results show that the static flow field is able to drive agents to the goals with a small number of requirements to update the path of agents. Meanwhile, the dipole flow field plays an important role to prevent collisions. The combination of

Toward Shared Working Space of Human and Robotic Agents Through Dipole Flow Field for Dependable Path Planning

Directory of Open Access Journals (Sweden)

Lan Anh Trinh

2018-06-01

Full Text Available Recent industrial developments in autonomous systems, or agents, which assume that humans and the agents share the same space or even work in close proximity, open for new challenges in robotics, especially in motion planning and control. In these settings, the control system should be able to provide these agents a reliable path following control when they are working in a group or in collaboration with one or several humans in complex and dynamic environments. In such scenarios, these agents are not only moving to reach their goals, i.e., locations, they are also aware of the movements of other entities to find a collision-free path. Thus, this paper proposes a dependable, i.e., safe, reliable and effective, path planning algorithm for a group of agents that share their working space with humans. Firstly, the method employs the Theta* algorithm to initialize the paths from a starting point to a goal for a set of agents. As Theta* algorithm is computationally heavy, it only reruns when there is a significant change of the environment. To deal with the movements of the agents, a static flow field along the configured path is defined. This field is used by the agents to navigate and reach their goals even if the planned trajectories are changed. Secondly, a dipole field is calculated to avoid the collision of agents with other agents and human subjects. In this approach, each agent is assumed to be a source of a magnetic dipole field in which the magnetic moment is aligned with the moving direction of the agent. The magnetic dipole-dipole interactions between these agents generate repulsive forces to help them to avoid collision. The effectiveness of the proposed approach has been evaluated with extensive simulations. The results show that the static flow field is able to drive agents to the goals with a small number of requirements to update the path of agents. Meanwhile, the dipole flow field plays an important role to prevent collisions. The

Design and testing of a model CELSS chamber robot

Science.gov (United States)

Davis, Mark; Dezego, Shawn; Jones, Kinzy; Kewley, Christopher; Langlais, Mike; McCarthy, John; Penny, Damon; Bonner, Tom; Funderburke, C. Ashley; Hailey, Ruth

1994-08-01

A robot system for use in an enclosed environment was designed and tested. The conceptual design will be used to assist in research performed by the Controlled Ecological Life Support System (CELSS) project. Design specifications include maximum load capacity, operation at specified environmental conditions, low maintenance, and safety. The robot system must not be hazardous to the sealed environment, and be capable of stowing and deploying within a minimum area of the CELSS chamber facility. This design consists of a telescoping robot arm that slides vertically on a shaft positioned in the center of the CELSS chamber. The telescoping robot arm consists of a series of links which can be fully extended to a length equal to the radius of the working envelope of the CELSS chamber. The vertical motion of the robot arm is achieved through the use of a combination ball screw/ball spline actuator system. The robot arm rotates cylindrically about the vertical axis through use of a turntable bearing attached to a central mounting structure fitted to the actuator shaft. The shaft is installed in an overhead rail system allowing the entire structure to be stowed and deployed within the CELSS chamber. The overhead rail system is located above the chamber's upper lamps and extends to the center of the CELSS chamber. The mounting interface of the actuator shaft and rail system allows the entire actuator shaft to be detached and removed from the CELSS chamber. When the actuator shaft is deployed, it is held fixed at the bottom of the chamber by placing a square knob on the bottom of the shaft into a recessed square fitting in the bottom of the chamber floor. A support boot ensures the rigidity of the shaft. Three student teams combined into one group designed a model of the CELSS chamber robot that they could build. They investigated materials, availability, and strength in their design. After the model arm and stand were built, the class performed pre-tests on the entire system

Extended Kalman filtering for model-based sensor fusion in robotics

International Nuclear Information System (INIS)

Fujii, Yuji; Wehe, D.K.; Lee, J.C.

1990-01-01

Remote surveillance and maintenance in advanced nuclear power plants will benefit from the increased utilization of mobile robotic systems. For these robotic systems to function most effectively in hazardous environments, they should be able to make decisions and take necessary actions with minimal human supervision. To accomplish this, the robot must be able to construct an accurate model of the power plant environment from diverse sensory data and a priori maps. In this paper, the authors demonstrate how a recursive parameter estimation technique known as Kalman filtering can integrate noisy data from various sensors to construct a consistent representation of the sensed environment

Understanding the Uncanny: Both Atypical Features and Category Ambiguity Provoke Aversion toward Humanlike Robots

Directory of Open Access Journals (Sweden)

Megan K. Strait

2017-08-01

Full Text Available Robots intended for social contexts are often designed with explicit humanlike attributes in order to facilitate their reception by (and communication with people. However, observation of an “uncanny valley”—a phenomenon in which highly humanlike entities provoke aversion in human observers—has lead some to caution against this practice. Both of these contrasting perspectives on the anthropomorphic design of social robots find some support in empirical investigations to date. Yet, owing to outstanding empirical limitations and theoretical disputes, the uncanny valley and its implications for human-robot interaction remains poorly understood. We thus explored the relationship between human similarity and people's aversion toward humanlike robots via manipulation of the agents' appearances. To that end, we employed a picture-viewing task (Nagents = 60 to conduct an experimental test (Nparticipants = 72 of the uncanny valley's existence and the visual features that cause certain humanlike robots to be unnerving. Across the levels of human similarity, we further manipulated agent appearance on two dimensions, typicality (prototypic, atypical, and ambiguous and agent identity (robot, person, and measured participants' aversion using both subjective and behavioral indices. Our findings were as follows: (1 Further substantiating its existence, the data show a clear and consistent uncanny valley in the current design space of humanoid robots. (2 Both category ambiguity, and more so, atypicalities provoke aversive responding, thus shedding light on the visual factors that drive people's discomfort. (3 Use of the Negative Attitudes toward Robots Scale did not reveal any significant relationships between people's pre-existing attitudes toward humanlike robots and their aversive responding—suggesting positive exposure and/or additional experience with robots is unlikely to affect the occurrence of an uncanny valley effect in humanoid robotics

Autonomous tracked robots in planar off-road conditions modelling, localization, and motion control

CERN Document Server

González, Ramón; Guzmán, José Luis

2014-01-01

This monograph is framed within the context of off-road mobile robotics. In particular, it discusses issues related to modelling, localization, and motion control of tracked mobile robots working in planar slippery conditions. Tracked locomotion constitutes a well-known solution for mobile platforms operating over diverse challenging terrains, for that reason, tracked robotics constitutes an important research field with many applications (e.g. agriculture, mining, search and rescue operations, military activities). The specific topics of this monograph are: historical perspective of tracked vehicles and tracked robots; trajectory-tracking model taking into account slip effect; visual-odometry-based localization strategies; and advanced slip-compensation motion controllers ensuring efficient real-time execution. Physical experiments with a real tracked robot are presented showing the better performance of the suggested novel approaches to known techniques.   Keywords: longitudinal slip, visual odometry, slip...

Research the Gait Characteristics of Human Walking Based on a Robot Model and Experiment

Science.gov (United States)

He, H. J.; Zhang, D. N.; Yin, Z. W.; Shi, J. H.

2017-02-01

In order to research the gait characteristics of human walking in different walking ways, a robot model with a single degree of freedom is put up in this paper. The system control models of the robot are established through Matlab/Simulink toolbox. The gait characteristics of straight, uphill, turning, up the stairs, down the stairs up and down areanalyzed by the system control models. To verify the correctness of the theoretical analysis, an experiment was carried out. The comparison between theoretical results and experimental results shows that theoretical results are better agreement with the experimental ones. Analyze the reasons leading to amplitude error and phase error and give the improved methods. The robot model and experimental ways can provide foundation to further research the various gait characteristics of the exoskeleton robot.

A conceptual and computational model of moral decision making in human and artificial agents.

Science.gov (United States)

Wallach, Wendell; Franklin, Stan; Allen, Colin

2010-07-01

Recently, there has been a resurgence of interest in general, comprehensive models of human cognition. Such models aim to explain higher-order cognitive faculties, such as deliberation and planning. Given a computational representation, the validity of these models can be tested in computer simulations such as software agents or embodied robots. The push to implement computational models of this kind has created the field of artificial general intelligence (AGI). Moral decision making is arguably one of the most challenging tasks for computational approaches to higher-order cognition. The need for increasingly autonomous artificial agents to factor moral considerations into their choices and actions has given rise to another new field of inquiry variously known as Machine Morality, Machine Ethics, Roboethics, or Friendly AI. In this study, we discuss how LIDA, an AGI model of human cognition, can be adapted to model both affective and rational features of moral decision making. Using the LIDA model, we will demonstrate how moral decisions can be made in many domains using the same mechanisms that enable general decision making. Comprehensive models of human cognition typically aim for compatibility with recent research in the cognitive and neural sciences. Global workspace theory, proposed by the neuropsychologist Bernard Baars (1988), is a highly regarded model of human cognition that is currently being computationally instantiated in several software implementations. LIDA (Franklin, Baars, Ramamurthy, & Ventura, 2005) is one such computational implementation. LIDA is both a set of computational tools and an underlying model of human cognition, which provides mechanisms that are capable of explaining how an agent's selection of its next action arises from bottom-up collection of sensory data and top-down processes for making sense of its current situation. We will describe how the LIDA model helps integrate emotions into the human decision-making process, and we

Modelling an Agent's Mind and Matter

NARCIS (Netherlands)

Jonker, C.M.; Treur, J.; Boman, M.

1997-01-01

In agent models often it is assumed that the agent maintains internal representations of the material world (e.g., its beliefs). An overall model of the agent and the material world necessarily incorporates sub-models for physical simulation and symbolic simulation, and a formalisation of the

Modelling Engagement in Multi-Party Conversations : Data-Driven Approaches to Understanding Human-Human Communication Patterns for Use in Human-Robot Interactions

OpenAIRE

Oertel, Catharine

2016-01-01

The aim of this thesis is to study human-human interaction in order to provide virtual agents and robots with the capability to engage into multi-party-conversations in a human-like-manner. The focus lies with the modelling of conversational dynamics and the appropriate realization of multi-modal feedback behaviour. For such an undertaking, it is important to understand how human-human communication unfolds in varying contexts and constellations over time. To this end, multi-modal human-human...

Modelling Behaviour Patterns of Pedestrians for Mobile Robot Trajectory Generation

Directory of Open Access Journals (Sweden)

Yusuke Tamura

2013-08-01

Full Text Available Robots are expected to be operated in environments where they coexist with humans, such as shopping malls and offices. Both the safety and efficiency of a robot are necessary in such environments. To achieve this, pedestrian behaviour should be accurately predicted. However, the behaviour is uncertain and cannot be easily predicted. This paper proposes a probabilistic method of determining pedestrian trajectory based on an estimation of pedestrian behaviour patterns. The proposed method focuses on the specific behaviour of pedestrians around the robot. The proposed model classifies the behaviours of pedestrians into definite patterns. The behaviour patterns, distribution of the positions of the pedestrians, and the direction of each behaviour pattern are determined by learning through observation. The behaviour pattern of a pedestrian can be estimated correctly by a likelihood calculation. A robot decides to move with an emphasis on either safety or efficiency depending on the result of the pattern estimation. If the pedestrian trajectory follows a known behaviour pattern, the robot would move with an emphasis on efficiency because the pedestrian trajectory can be predicted. Otherwise, the robot would move with an emphasis on safety because the behaviour of the pedestrian cannot be predicted. Experimental results show that robots can move efficiently and safely when passing by a pedestrian by applying the proposed method.

Dual-Schemata Model

Science.gov (United States)

Taniguchi, Tadahiro; Sawaragi, Tetsuo

In this paper, a new machine-learning method, called Dual-Schemata model, is presented. Dual-Schemata model is a kind of self-organizational machine learning methods for an autonomous robot interacting with an unknown dynamical environment. This is based on Piaget's Schema model, that is a classical psychological model to explain memory and cognitive development of human beings. Our Dual-Schemata model is developed as a computational model of Piaget's Schema model, especially focusing on sensori-motor developing period. This developmental process is characterized by a couple of two mutually-interacting dynamics; one is a dynamics formed by assimilation and accommodation, and the other dynamics is formed by equilibration and differentiation. By these dynamics schema system enables an agent to act well in a real world. This schema's differentiation process corresponds to a symbol formation process occurring within an autonomous agent when it interacts with an unknown, dynamically changing environment. Experiment results obtained from an autonomous facial robot in which our model is embedded are presented; an autonomous facial robot becomes able to chase a ball moving in various ways without any rewards nor teaching signals from outside. Moreover, emergence of concepts on the target movements within a robot is shown and discussed in terms of fuzzy logics on set-subset inclusive relationships.

Soft Robotics Week

CERN Document Server

Rossiter, Jonathan; Iida, Fumiya; Cianchetti, Matteo; Margheri, Laura

2017-01-01

This book offers a comprehensive, timely snapshot of current research, technologies and applications of soft robotics. The different chapters, written by international experts across multiple fields of soft robotics, cover innovative systems and technologies for soft robot legged locomotion, soft robot manipulation, underwater soft robotics, biomimetic soft robotic platforms, plant-inspired soft robots, flying soft robots, soft robotics in surgery, as well as methods for their modeling and control. Based on the results of the second edition of the Soft Robotics Week, held on April 25 – 30, 2016, in Livorno, Italy, the book reports on the major research lines and novel technologies presented and discussed during the event.

Improvement of a Robotic Manipulator Model Based on Multivariate Residual Modeling

Directory of Open Access Journals (Sweden)

Serge Gale

2017-07-01

Full Text Available A new method is presented for extending a dynamic model of a six degrees of freedom robotic manipulator. A non-linear multivariate calibration of input–output training data from several typical motion trajectories is carried out with the aim of predicting the model systematic output error at time (t + 1 from known input reference up till and including time (t. A new partial least squares regression (PLSR based method, nominal PLSR with interactions was developed and used to handle, unmodelled non-linearities. The performance of the new method is compared with least squares (LS. Different cross-validation schemes were compared in order to assess the sampling of the state space based on conventional trajectories. The method developed in the paper can be used as fault monitoring mechanism and early warning system for sensor failure. The results show that the suggested methods improves trajectory tracking performance of the robotic manipulator by extending the initial dynamic model of the manipulator.

Multiagent Modeling and Simulation in Human-Robot Mission Operations Work System Design

Science.gov (United States)

Sierhuis, Maarten; Clancey, William J.; Sims, Michael H.; Shafto, Michael (Technical Monitor)

2001-01-01

This paper describes a collaborative multiagent modeling and simulation approach for designing work systems. The Brahms environment is used to model mission operations for a semi-autonomous robot mission to the Moon at the work practice level. It shows the impact of human-decision making on the activities and energy consumption of a robot. A collaborative work systems design methodology is described that allows informal models, created with users and stakeholders, to be used as input to the development of formal computational models.

Singularity now: using the ventricular assist device as a model for future human-robotic physiology.

Science.gov (United States)

Martin, Archer K

2016-04-01

In our 21 st century world, human-robotic interactions are far more complicated than Asimov predicted in 1942. The future of human-robotic interactions includes human-robotic machine hybrids with an integrated physiology, working together to achieve an enhanced level of baseline human physiological performance. This achievement can be described as a biological Singularity. I argue that this time of Singularity cannot be met by current biological technologies, and that human-robotic physiology must be integrated for the Singularity to occur. In order to conquer the challenges we face regarding human-robotic physiology, we first need to identify a working model in today's world. Once identified, this model can form the basis for the study, creation, expansion, and optimization of human-robotic hybrid physiology. In this paper, I present and defend the line of argument that currently this kind of model (proposed to be named "IshBot") can best be studied in ventricular assist devices - VAD.

Requirements Modeling with Agent Programming

Science.gov (United States)

Dasgupta, Aniruddha; Krishna, Aneesh; Ghose, Aditya K.

Agent-oriented conceptual modeling notations are highly effective in representing requirements from an intentional stance and answering questions such as what goals exist, how key actors depend on each other, and what alternatives must be considered. In this chapter, we review an approach to executing i* models by translating these into set of interacting agents implemented in the CASO language and suggest how we can perform reasoning with requirements modeled (both functional and non-functional) using i* models. In this chapter we particularly incorporate deliberation into the agent design. This allows us to benefit from the complementary representational capabilities of the two frameworks.

The internet and intelligent machines: search engines, agents and robots; Radiologische Informationssuche im Internet: Datenbanken, Suchmaschinen und intelligente Agenten

Energy Technology Data Exchange (ETDEWEB)

Achenbach, S; Alfke, H [Marburg Univ. (Germany). Abt. fuer Strahlendiagnostik

2000-04-01

The internet plays an important role in a growing number of medical applications. Finding relevant information is not always easy as the amount of available information on the Web is rising quickly. Even the best Search Engines can only collect links to a fraction of all existing Web pages. In addition, many of these indexed documents have been changed or deleted. The vast majority of information on the Web is not searchable with conventional methods. New search strategies, technologies and standards are combined in Intelligent Search Agents (ISA) an Robots, which can retrieve desired information in a specific approach. Conclusion: The article describes differences between ISAs and conventional Search Engines and how communication between Agents improves their ability to find information. Examples of existing ISAs are given and the possible influences on the current and future work in radiology is discussed. (orig.) [German] Das Internet findet zunehmend in medizinischen Anwendungen Verbreitung, jedoch ist das Auffinden relevanter Informationen nicht immer leicht. Die Anzahl der verfuegbaren Dokumente im World wide web nimmt so schnell zu, dass die Suche zunehmend Probleme bereitet: Auch gute Suchmaschinen erfassen nur einige Prozent der vorhandenen Seiten in Ihren Datenbanken. Zusaetzlich sorgen staendige Veraenderungen dafuer, dass nur ein Teil dieser durchsuchbaren Dokumente ueberhaupt noch existiert. Der Grossteil des Internets ist daher mit konventionellen Methoden nicht zu erschliessen. Neue Standards, Suchstrategien und Technologien vereinen sich in den Suchagenten und Robots, die gezielter und intelligenter Inhalte ermitteln koennen. Schlussfolgerung: Der Artikel stellt dar, wie sich ein Intelligent search agent (ISA) von einer Suchmaschine unterscheidet und durch Kooperation mit anderen Agenten die Anforderungen der Benutzer besser erfuellen kann. Neben den Grundlagen werden exemplarische Anwendungen gezeigt, die heute im Netz existieren, und ein Ausblick

A Plug and Produce Framework for Industrial Collaborative Robots

DEFF Research Database (Denmark)

Schou, Casper; Madsen, Ole

2017-01-01

Collaborative robots are today ever more interesting in response to the increasing need for agile manufacturing equipment. Contrary to traditional industrial robots, collaborative robots are intended for working in dynamic environments alongside the production staff. To cope with the dynamic...... environment and workflow, new configuration and control methods are needed compared to those of traditional industrial robots. The new methods should enable shop floor operators to reconfigure the robot. This article presents a plug and produce framework for industrial collaborative robots. The article...... focuses on the control framework enabling quick and easy exchange of hardware modules as an approach to achieving plug and produce. To solve this, an agent-based system is proposed building on top of the robot operating system. The framework enables robot operating system packages to be adapted...

Generating Self-Reliant Teams of Autonomous Cooperating Robots: Desired design Characteristics

Energy Technology Data Exchange (ETDEWEB)

Parker, L.E.

1999-05-01

The difficulties in designing a cooperative team are significant. Several of the key questions that must be resolved when designing a cooperative control architecture include: How do we formulate, describe, decompose, and allocate problems among a group of intelligent agents? How do we enable agents to communicate and interact? How do we ensure that agents act coherently in their actions? How do we allow agents to recognize and reconcile conflicts? However, in addition to these key issues, the software architecture must be designed to enable multi-robot teams to be robust, reliable, and flexible. Without these capabilities, the resulting robot team will not be able to successfully deal with the dynamic and uncertain nature of the real world. In this extended abstract, we first describe these desired capabilities. We then briefly describe the ALLIANCE software architecture that we have previously developed for multi-robot cooperation. We then briefly analyze the ALLIANCE architecture in terms of the desired design qualities identified.

RIPE [robot independent programming environment]: A robot independent programming environment

International Nuclear Information System (INIS)

Miller, D.J.; Lennox, R.C.

1990-01-01

Remote manual operations in radiation environments are typically performed very slowly. Sensor-based computer-controlled robots hold great promise for increasing the speed and safety of remote operations; however, the programming of robotic systems has proven to be expensive and difficult. Generalized approaches to robot programming that reuse available software modules and employ programming languages which are independent of the specific robotic and sensory devices being used are needed to speed software development and increase overall system reliability. This paper discusses the robot independent programming environment (RIPE) developed at Sandia National Laboratories (SNL). The RIPE is an object-oriented approach to robot system architectures; it is a software environment that facilitates rapid design and implementation of complex robot systems for diverse applications. An architecture based on hierarchies of distributed multiprocessors provides the computing platform for a layered programming structure that models applications using software objects. These objects are designed to support model-based automated programming of robotic and machining devices, real-time sensor-based control, error handling, and robust communication

Toward understanding social cues and signals in human-robot interaction: effects of robot gaze and proxemic behavior.

Science.gov (United States)

Fiore, Stephen M; Wiltshire, Travis J; Lobato, Emilio J C; Jentsch, Florian G; Huang, Wesley H; Axelrod, Benjamin

2013-01-01

As robots are increasingly deployed in settings requiring social interaction, research is needed to examine the social signals perceived by humans when robots display certain social cues. In this paper, we report a study designed to examine how humans interpret social cues exhibited by robots. We first provide a brief overview of perspectives from social cognition in humans and how these processes are applicable to human-robot interaction (HRI). We then discuss the need to examine the relationship between social cues and signals as a function of the degree to which a robot is perceived as a socially present agent. We describe an experiment in which social cues were manipulated on an iRobot Ava(TM) mobile robotics platform in a hallway navigation scenario. Cues associated with the robot's proxemic behavior were found to significantly affect participant perceptions of the robot's social presence and emotional state while cues associated with the robot's gaze behavior were not found to be significant. Further, regardless of the proxemic behavior, participants attributed more social presence and emotional states to the robot over repeated interactions than when they first interacted with it. Generally, these results indicate the importance for HRI research to consider how social cues expressed by a robot can differentially affect perceptions of the robot's mental states and intentions. The discussion focuses on implications for the design of robotic systems and future directions for research on the relationship between social cues and signals.

Can young children learn words from a robot?

OpenAIRE

Moriguchi, Yusuke; Kanda, Takayuki; Ishiguro, Hiroshi; Shimada, Yoko; Itakura, Shoji

2011-01-01

Young children generally learn words from other people. Recent research has shown that children can learn new actions and skills from nonhuman agents. This study examines whether young children could learn words from a robot. Preschool children were shown a video in which either a woman (human condition) or a mechanical robot (robot condition) labeled novel objects. Then the children were asked to select the objects according to the names used in the video. The results revealed that children ...

Graphical models for simulation and control of robotic systems for waste handling

International Nuclear Information System (INIS)

Drotning, W.D.; Bennett, P.C.

1992-01-01

This paper discusses detailed geometric models which have been used within a graphical simulation environment to study transportation cask facility design and to perform design and analyses of robotic systems for handling of nuclear waste. The models form the basis for a robot control environment which provides safety, flexibility, and reliability for operations which span the spectrum from autonomous control to tasks requiring direct human intervention

Detecting Biological Motion for Human–Robot Interaction: A Link between Perception and Action

Directory of Open Access Journals (Sweden)

Alessia Vignolo

2017-06-01

Full Text Available One of the fundamental skills supporting safe and comfortable interaction between humans is their capability to understand intuitively each other’s actions and intentions. At the basis of this ability is a special-purpose visual processing that human brain has developed to comprehend human motion. Among the first “building blocks” enabling the bootstrapping of such visual processing is the ability to detect movements performed by biological agents in the scene, a skill mastered by human babies in the first days of their life. In this paper, we present a computational model based on the assumption that such visual ability must be based on local low-level visual motion features, which are independent of shape, such as the configuration of the body and perspective. Moreover, we implement it on the humanoid robot iCub, embedding it into a software architecture that leverages the regularities of biological motion also to control robot attention and oculomotor behaviors. In essence, we put forth a model in which the regularities of biological motion link perception and action enabling a robotic agent to follow a human-inspired sensory-motor behavior. We posit that this choice facilitates mutual understanding and goal prediction during collaboration, increasing the pleasantness and safety of the interaction.

Model predictive Controller for Mobile Robot

OpenAIRE

Alireza Rezaee

2017-01-01

This paper proposes a Model Predictive Controller (MPC) for control of a P2AT mobile robot. MPC refers to a group of controllers that employ a distinctly identical model of process to predict its future behavior over an extended prediction horizon. The design of a MPC is formulated as an optimal control problem. Then this problem is considered as linear quadratic equation (LQR) and is solved by making use of Ricatti equation. To show the effectiveness of the proposed method this controller is...

Modeling and Simulation of Elementary Robot Behaviors using Associative Memories

Directory of Open Access Journals (Sweden)

Claude F. Touzet

2006-06-01

Full Text Available Today, there are several drawbacks that impede the necessary and much needed use of robot learning techniques in real applications. First, the time needed to achieve the synthesis of any behavior is prohibitive. Second, the robot behavior during the learning phase is – by definition – bad, it may even be dangerous. Third, except within the lazy learning approach, a new behavior implies a new learning phase. We propose in this paper to use associative memories (self-organizing maps to encode the non explicit model of the robot-world interaction sampled by the lazy memory, and then generate a robot behavior by means of situations to be achieved, i.e., points on the self-organizing maps. Any behavior can instantaneously be synthesized by the definition of a goal situation. Its performance will be minimal (not necessarily bad and will improve by the mere repetition of the behavior.

An upper limb robot model of children limb for cerebral palsy neurorehabilitation.

Science.gov (United States)

Pathak, Yagna; Johnson, Michelle

2012-01-01

Robot therapy has emerged in the last few decades as a tool to help patients with neurological injuries relearn motor tasks and improve their quality of life. The main goal of this study was to develop a simple model of the human arm for children affected with cerebral palsy (CP). The Simulink based model presented here shows a comparison for children with and without disabilities (ages 6-15) with normal and reduced range of motion in the upper limb. The model incorporates kinematic and dynamic considerations required for activities of daily living. The simulation was conducted using Matlab/Simulink and will eventually be integrated with a robotic counterpart to develop a physical robot that will provide assistance in activities of daily life (ADLs) to children with CP while also aiming to improve motor recovery.

Mathematical model and metaheuristics for simultaneous balancing and sequencing of a robotic mixed-model assembly line

Science.gov (United States)

Li, Zixiang; Janardhanan, Mukund Nilakantan; Tang, Qiuhua; Nielsen, Peter

2018-05-01

This article presents the first method to simultaneously balance and sequence robotic mixed-model assembly lines (RMALB/S), which involves three sub-problems: task assignment, model sequencing and robot allocation. A new mixed-integer programming model is developed to minimize makespan and, using CPLEX solver, small-size problems are solved for optimality. Two metaheuristics, the restarted simulated annealing algorithm and co-evolutionary algorithm, are developed and improved to address this NP-hard problem. The restarted simulated annealing method replaces the current temperature with a new temperature to restart the search process. The co-evolutionary method uses a restart mechanism to generate a new population by modifying several vectors simultaneously. The proposed algorithms are tested on a set of benchmark problems and compared with five other high-performing metaheuristics. The proposed algorithms outperform their original editions and the benchmarked methods. The proposed algorithms are able to solve the balancing and sequencing problem of a robotic mixed-model assembly line effectively and efficiently.

HoverBots: Precise Locomotion Using Robots That Are Designed for Manufacturability

Directory of Open Access Journals (Sweden)

Markus P. Nemitz

2017-11-01

Full Text Available Scaling up robot swarms to collectives of hundreds or even thousands without sacrificing sensing, processing, and locomotion capabilities is a challenging problem. Low-cost robots are potentially scalable, but the majority of existing systems have limited capabilities, and these limitations substantially constrain the type of experiments that could be performed by robotics researchers. As an alternative to increasing the quantity of robots by reducing their functionality, we have developed a new technology that delivers increased functionality at low-cost. In this study, we present a comprehensive literature review on the most commonly used locomotion strategies of swarm robotic systems. We introduce a new type of low-friction locomotion—active low-friction locomotion—and we show its first implementation in the HoverBot system. The HoverBot system consists of an air levitation and magnet table, and a HoverBot agent. HoverBot agents are levitating circuit boards that we have equipped with an array of planar coils and a Hall-effect sensor. The HoverBot agent uses its coils to pull itself toward magnetic anchors that are embedded into a levitation table. These robots use active low-friction locomotion; consist of only surface-mount components; circumvent actuator calibration; are capable of odometry by using a single Hall-effect sensor; and perform precise movement. We conducted three hours of experimental evaluation of the HoverBot system in which we observed the system performing more than 10,000 steps. We also demonstrate formation movement, random collision, and straight collisions with two robots. This study demonstrates that active low-friction locomotion is an alternative to wheeled and slip-stick locomotion in the field of swarm robotics.

Evolutionary autonomous agents and the nature of apraxia

Directory of Open Access Journals (Sweden)

Jin Frank

2005-01-01

Full Text Available Abstract Background Evolutionary autonomous agents are robots or robot simulations whose controller is a dynamical neural network and whose evolution occurs autonomously under the guidance of a fitness function without the detailed or explicit direction of an external programmer. They are embodied agents with a simple neural network controller and as such they provide the optimal forum by which sensorimotor interactions in a specified environment can be studied without the computational assumptions inherent in standard neuroscience. Methods Evolutionary autonomous agents were evolved that were able to perform identical movements under two different contexts, one which represented an automatic movement and one which had a symbolic context. In an attempt to model the automatic-voluntary dissociation frequently seen in ideomotor apraxia, lesions were introduced into the neural network controllers resulting in a behavioral dissociation with loss of the ability to perform the movement which had a symbolic context and preservation of the simpler, automatic movement. Results Analysis of the changes in the hierarchical organization of the networks in the apractic EAAs demonstrated consistent changes in the network dynamics across all agents with loss of longer duration time scales in the network dynamics. Conclusion The concepts of determinate motor programs and perceptual representations that are implicit in the present day understanding of ideomotor apraxia are assumptions inherent in the computational understanding of brain function. The strength of the present study using EAAs to model one aspect of ideomotor apraxia is the absence of these assumptions and a grounding of all sensorimotor interactions in an embodied, autonomous agent. The consistency of the hierarchical changes in the network dynamics across all apractic agents demonstrates that this technique is tenable and will be a valuable adjunct to a computational formalism in the understanding

Modelling and Experiment Based on a Navigation System for a Cranio-Maxillofacial Surgical Robot

Directory of Open Access Journals (Sweden)

Xingguang Duan

2018-01-01

Full Text Available In view of the characteristics of high risk and high accuracy in cranio-maxillofacial surgery, we present a novel surgical robot system that can be used in a variety of surgeries. The surgical robot system can assist surgeons in completing biopsy of skull base lesions, radiofrequency thermocoagulation of the trigeminal ganglion, and radioactive particle implantation of skull base malignant tumors. This paper focuses on modelling and experimental analyses of the robot system based on navigation technology. Firstly, the transformation relationship between the subsystems is realized based on the quaternion and the iterative closest point registration algorithm. The hand-eye coordination model based on optical navigation is established to control the end effector of the robot moving to the target position along the planning path. The closed-loop control method, “kinematics + optics” hybrid motion control method, is presented to improve the positioning accuracy of the system. Secondly, the accuracy of the system model was tested by model experiments. And the feasibility of the closed-loop control method was verified by comparing the positioning accuracy before and after the application of the method. Finally, the skull model experiments were performed to evaluate the function of the surgical robot system. The results validate its feasibility and are consistent with the preoperative surgical planning.

Modelling and Experiment Based on a Navigation System for a Cranio-Maxillofacial Surgical Robot

Science.gov (United States)

Duan, Xingguang; Gao, Liang; Li, Jianxi; Li, Haoyuan; Guo, Yanjun

2018-01-01

In view of the characteristics of high risk and high accuracy in cranio-maxillofacial surgery, we present a novel surgical robot system that can be used in a variety of surgeries. The surgical robot system can assist surgeons in completing biopsy of skull base lesions, radiofrequency thermocoagulation of the trigeminal ganglion, and radioactive particle implantation of skull base malignant tumors. This paper focuses on modelling and experimental analyses of the robot system based on navigation technology. Firstly, the transformation relationship between the subsystems is realized based on the quaternion and the iterative closest point registration algorithm. The hand-eye coordination model based on optical navigation is established to control the end effector of the robot moving to the target position along the planning path. The closed-loop control method, “kinematics + optics” hybrid motion control method, is presented to improve the positioning accuracy of the system. Secondly, the accuracy of the system model was tested by model experiments. And the feasibility of the closed-loop control method was verified by comparing the positioning accuracy before and after the application of the method. Finally, the skull model experiments were performed to evaluate the function of the surgical robot system. The results validate its feasibility and are consistent with the preoperative surgical planning. PMID:29599948

A neural network-based exploratory learning and motor planning system for co-robots

Directory of Open Access Journals (Sweden)

Byron V Galbraith

2015-07-01

Full Text Available Collaborative robots, or co-robots, are semi-autonomous robotic agents designed to work alongside humans in shared workspaces. To be effective, co-robots require the ability to respond and adapt to dynamic scenarios encountered in natural environments. One way to achieve this is through exploratory learning, or learning by doing, an unsupervised method in which co-robots are able to build an internal model for motor planning and coordination based on real-time sensory inputs. In this paper, we present an adaptive neural network-based system for co-robot control that employs exploratory learning to achieve the coordinated motor planning needed to navigate toward, reach for, and grasp distant objects. To validate this system we used the 11-degrees-of-freedom RoPro Calliope mobile robot. Through motor babbling of its wheels and arm, the Calliope learned how to relate visual and proprioceptive information to achieve hand-eye-body coordination. By continually evaluating sensory inputs and externally provided goal directives, the Calliope was then able to autonomously select the appropriate wheel and joint velocities needed to perform its assigned task, such as following a moving target or retrieving an indicated object.

A neural network-based exploratory learning and motor planning system for co-robots.

Science.gov (United States)

Galbraith, Byron V; Guenther, Frank H; Versace, Massimiliano

2015-01-01

Collaborative robots, or co-robots, are semi-autonomous robotic agents designed to work alongside humans in shared workspaces. To be effective, co-robots require the ability to respond and adapt to dynamic scenarios encountered in natural environments. One way to achieve this is through exploratory learning, or "learning by doing," an unsupervised method in which co-robots are able to build an internal model for motor planning and coordination based on real-time sensory inputs. In this paper, we present an adaptive neural network-based system for co-robot control that employs exploratory learning to achieve the coordinated motor planning needed to navigate toward, reach for, and grasp distant objects. To validate this system we used the 11-degrees-of-freedom RoPro Calliope mobile robot. Through motor babbling of its wheels and arm, the Calliope learned how to relate visual and proprioceptive information to achieve hand-eye-body coordination. By continually evaluating sensory inputs and externally provided goal directives, the Calliope was then able to autonomously select the appropriate wheel and joint velocities needed to perform its assigned task, such as following a moving target or retrieving an indicated object.

Knowledge transfer for learning robot models via local procrustes analysis

CSIR Research Space (South Africa)

Makondo, N

2015-11-01

Full Text Available Learning of robot kinematic and dynamic models from data has attracted much interest recently as an alternative to manually defined models. However, the amount of data required to learn these models becomes large when the number of degrees...

Modeling and Simulation of Wave Gait of a Hexapod Walking Robot: A CAD/CAE Approach

Directory of Open Access Journals (Sweden)

Abhijit Mahapatra

2013-03-01

Full Text Available In the present paper, an attempt has been made to carry out dynamic analysis of a hexapod robot using the concept of multibody dynamics. A CAD (Computer Aided Design model of a realistic hexapod robot has been made for dynamic simulation of its locomotion using ADAMS (Automatic Dynamic Analysis of Mechanical Systems multibody dynamics solver. The kinematic model of each leg of three degrees of freedom has been designed using CATIA (Computer Aided Three Dimensional Interactive Application and SimDesigner package in order to develop an overall kinematic model of the robot, when it follows a straight path. Joint Torque variation as well as the variation of the aggregate center of mass of the robot was analyzed for the wave tetrapod gait. The simulation results provide the basis for developing the control algorithm as well as an intelligent decision making for the robot while in motion.

High effective inverse dynamics modelling for dual-arm robot

Science.gov (United States)

Shen, Haoyu; Liu, Yanli; Wu, Hongtao

2018-05-01

To deal with the problem of inverse dynamics modelling for dual arm robot, a recursive inverse dynamics modelling method based on decoupled natural orthogonal complement is presented. In this model, the concepts and methods of Decoupled Natural Orthogonal Complement matrices are used to eliminate the constraint forces in the Newton-Euler kinematic equations, and the screws is used to express the kinematic and dynamics variables. On this basis, the paper has developed a special simulation program with symbol software of Mathematica and conducted a simulation research on the a dual-arm robot. Simulation results show that the proposed method based on decoupled natural orthogonal complement can save an enormous amount of CPU time that was spent in computing compared with the recursive Newton-Euler kinematic equations and the results is correct and reasonable, which can verify the reliability and efficiency of the method.

Human Robot Interaction for Hybrid Collision Avoidance System for Indoor Mobile Robots

Directory of Open Access Journals (Sweden)

Mazen Ghandour

2017-06-01

Full Text Available In this paper, a novel approach for collision avoidance for indoor mobile robots based on human-robot interaction is realized. The main contribution of this work is a new technique for collision avoidance by engaging the human and the robot in generating new collision-free paths. In mobile robotics, collision avoidance is critical for the success of the robots in implementing their tasks, especially when the robots navigate in crowded and dynamic environments, which include humans. Traditional collision avoidance methods deal with the human as a dynamic obstacle, without taking into consideration that the human will also try to avoid the robot, and this causes the people and the robot to get confused, especially in crowded social places such as restaurants, hospitals, and laboratories. To avoid such scenarios, a reactive-supervised collision avoidance system for mobile robots based on human-robot interaction is implemented. In this method, both the robot and the human will collaborate in generating the collision avoidance via interaction. The person will notify the robot about the avoidance direction via interaction, and the robot will search for the optimal collision-free path on the selected direction. In case that no people interacted with the robot, it will select the navigation path autonomously and select the path that is closest to the goal location. The humans will interact with the robot using gesture recognition and Kinect sensor. To build the gesture recognition system, two models were used to classify these gestures, the first model is Back-Propagation Neural Network (BPNN, and the second model is Support Vector Machine (SVM. Furthermore, a novel collision avoidance system for avoiding the obstacles is implemented and integrated with the HRI system. The system is tested on H20 robot from DrRobot Company (Canada and a set of experiments were implemented to report the performance of the system in interacting with the human and avoiding

Smart swarms of bacteria-inspired agents with performance adaptable interactions.

Directory of Open Access Journals (Sweden)

Adi Shklarsh

2011-09-01

Full Text Available Collective navigation and swarming have been studied in animal groups, such as fish schools, bird flocks, bacteria, and slime molds. Computer modeling has shown that collective behavior of simple agents can result from simple interactions between the agents, which include short range repulsion, intermediate range alignment, and long range attraction. Here we study collective navigation of bacteria-inspired smart agents in complex terrains, with adaptive interactions that depend on performance. More specifically, each agent adjusts its interactions with the other agents according to its local environment--by decreasing the peers' influence while navigating in a beneficial direction, and increasing it otherwise. We show that inclusion of such performance dependent adaptable interactions significantly improves the collective swarming performance, leading to highly efficient navigation, especially in complex terrains. Notably, to afford such adaptable interactions, each modeled agent requires only simple computational capabilities with short-term memory, which can easily be implemented in simple swarming robots.

Smart swarms of bacteria-inspired agents with performance adaptable interactions.

Science.gov (United States)

Shklarsh, Adi; Ariel, Gil; Schneidman, Elad; Ben-Jacob, Eshel

2011-09-01

Collective navigation and swarming have been studied in animal groups, such as fish schools, bird flocks, bacteria, and slime molds. Computer modeling has shown that collective behavior of simple agents can result from simple interactions between the agents, which include short range repulsion, intermediate range alignment, and long range attraction. Here we study collective navigation of bacteria-inspired smart agents in complex terrains, with adaptive interactions that depend on performance. More specifically, each agent adjusts its interactions with the other agents according to its local environment--by decreasing the peers' influence while navigating in a beneficial direction, and increasing it otherwise. We show that inclusion of such performance dependent adaptable interactions significantly improves the collective swarming performance, leading to highly efficient navigation, especially in complex terrains. Notably, to afford such adaptable interactions, each modeled agent requires only simple computational capabilities with short-term memory, which can easily be implemented in simple swarming robots.

Learning to Automatically Detect Features for Mobile Robots Using Second-Order Hidden Markov Models

Directory of Open Access Journals (Sweden)

Olivier Aycard

2004-12-01

Full Text Available In this paper, we propose a new method based on Hidden Markov Models to interpret temporal sequences of sensor data from mobile robots to automatically detect features. Hidden Markov Models have been used for a long time in pattern recognition, especially in speech recognition. Their main advantages over other methods (such as neural networks are their ability to model noisy temporal signals of variable length. We show in this paper that this approach is well suited for interpretation of temporal sequences of mobile-robot sensor data. We present two distinct experiments and results: the first one in an indoor environment where a mobile robot learns to detect features like open doors or T-intersections, the second one in an outdoor environment where a different mobile robot has to identify situations like climbing a hill or crossing a rock.

Accuracy improvement of a hybrid robot for ITER application using POE modeling method

International Nuclear Information System (INIS)

Wang, Yongbo; Wu, Huapeng; Handroos, Heikki

2013-01-01

Highlights: ► The product of exponential (POE) formula for error modeling of hybrid robot. ► Differential Evolution (DE) algorithm for parameter identification. ► Simulation results are given to verify the effectiveness of the method. -- Abstract: This paper focuses on the kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial–parallel hybrid robot to improve its accuracy. The robot was designed to perform the assembling and repairing tasks of the vacuum vessel (VV) of the international thermonuclear experimental reactor (ITER). By employing the product of exponentials (POEs) formula, we extended the POE-based calibration method from serial robot to redundant serial–parallel hybrid robot. The proposed method combines the forward and inverse kinematics together to formulate a hybrid calibration method for serial–parallel hybrid robot. Because of the high nonlinear characteristics of the error model and too many error parameters need to be identified, the traditional iterative linear least-square algorithms cannot be used to identify the parameter errors. This paper employs a global optimization algorithm, Differential Evolution (DE), to identify parameter errors by solving the inverse kinematics of the hybrid robot. Furthermore, after the parameter errors were identified, the DE algorithm was adopted to numerically solve the forward kinematics of the hybrid robot to demonstrate the accuracy improvement of the end-effector. Numerical simulations were carried out by generating random parameter errors at the allowed tolerance limit and generating a number of configuration poses in the robot workspace. Simulation of the real experimental conditions shows that the accuracy of the end-effector can be improved to the same precision level of the given external measurement device

Accuracy improvement of a hybrid robot for ITER application using POE modeling method

Energy Technology Data Exchange (ETDEWEB)

Wang, Yongbo, E-mail: yongbo.wang@hotmail.com [Laboratory of Intelligent Machines, Lappeenranta University of Technology, FIN-53851 Lappeenranta (Finland); Wu, Huapeng; Handroos, Heikki [Laboratory of Intelligent Machines, Lappeenranta University of Technology, FIN-53851 Lappeenranta (Finland)

2013-10-15

Highlights: ► The product of exponential (POE) formula for error modeling of hybrid robot. ► Differential Evolution (DE) algorithm for parameter identification. ► Simulation results are given to verify the effectiveness of the method. -- Abstract: This paper focuses on the kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial–parallel hybrid robot to improve its accuracy. The robot was designed to perform the assembling and repairing tasks of the vacuum vessel (VV) of the international thermonuclear experimental reactor (ITER). By employing the product of exponentials (POEs) formula, we extended the POE-based calibration method from serial robot to redundant serial–parallel hybrid robot. The proposed method combines the forward and inverse kinematics together to formulate a hybrid calibration method for serial–parallel hybrid robot. Because of the high nonlinear characteristics of the error model and too many error parameters need to be identified, the traditional iterative linear least-square algorithms cannot be used to identify the parameter errors. This paper employs a global optimization algorithm, Differential Evolution (DE), to identify parameter errors by solving the inverse kinematics of the hybrid robot. Furthermore, after the parameter errors were identified, the DE algorithm was adopted to numerically solve the forward kinematics of the hybrid robot to demonstrate the accuracy improvement of the end-effector. Numerical simulations were carried out by generating random parameter errors at the allowed tolerance limit and generating a number of configuration poses in the robot workspace. Simulation of the real experimental conditions shows that the accuracy of the end-effector can be improved to the same precision level of the given external measurement device.

A problem of optimal control and observation for distributed homogeneous multi-agent system

Science.gov (United States)

Kruglikov, Sergey V.

2017-12-01

The paper considers the implementation of a algorithm for controlling a distributed complex of several mobile multi-robots. The concept of a unified information space of the controlling system is applied. The presented information and mathematical models of participants and obstacles, as real agents, and goals and scenarios, as virtual agents, create the base forming the algorithmic and software background for computer decision support system. The controlling scheme assumes the indirect management of the robotic team on the basis of optimal control and observation problem predicting intellectual behavior in a dynamic, hostile environment. A basic content problem is a compound cargo transportation by a group of participants in the case of a distributed control scheme in the terrain with multiple obstacles.

IMPERA: Integrated Mission Planning for Multi-Robot Systems

Directory of Open Access Journals (Sweden)

Daniel Saur

2015-10-01

Full Text Available This paper presents the results of the project IMPERA (Integrated Mission Planning for Distributed Robot Systems. The goal of IMPERA was to realize an extraterrestrial exploration scenario using a heterogeneous multi-robot system. The main challenge was the development of a multi-robot planning and plan execution architecture. The robot team consists of three heterogeneous robots, which have to explore an unknown environment and collect lunar drill samples. The team activities are described using the language ALICA (A Language for Interactive Agents. Furthermore, we use the mission planning system pRoPhEt MAS (Reactive Planning Engine for Multi-Agent Systems to provide an intuitive interface to generate team activities. Therefore, we define the basic skills of our team with ALICA and define the desired goal states by using a logic description. Based on the skills, pRoPhEt MAS creates a valid ALICA plan, which will be executed by the team. The paper describes the basic components for communication, coordinated exploration, perception and object transportation. Finally, we evaluate the planning engine pRoPhEt MAS in the IMPERA scenario. In addition, we present further evaluation of pRoPhEt MAS in more dynamic environments.

Grasping in Robotics

CERN Document Server

2013-01-01

Grasping in Robotics contains original contributions in the field of grasping in robotics with a broad multidisciplinary approach. This gives the possibility of addressing all the major issues related to robotized grasping, including milestones in grasping through the centuries, mechanical design issues, control issues, modelling achievements and issues, formulations and software for simulation purposes, sensors and vision integration, applications in industrial field and non-conventional applications (including service robotics and agriculture).   The contributors to this book are experts in their own diverse and wide ranging fields. This multidisciplinary approach can help make Grasping in Robotics of interest to a very wide audience. In particular, it can be a useful reference book for researchers, students and users in the wide field of grasping in robotics from many different disciplines including mechanical design, hardware design, control design, user interfaces, modelling, simulation, sensors and hum...

Compliance Modeling and Error Compensation of a 3-Parallelogram Lightweight Robotic Arm

DEFF Research Database (Denmark)

Wu, Guanglei; Guo, Sheng; Bai, Shaoping

2015-01-01

This paper presents compliance modeling and error compensation for lightweight robotic arms built with parallelogram linkages, i.e., Π joints. The Cartesian stiffness matrix is derived using the virtual joint method. Based on the developed stiffness model, a method to compensate the compliance...... error is introduced, being illustrated with a 3-parallelogram robot in the application of pick-and-place operation. The results show that this compensation method can effectively improve the operation accuracy....

Magnetically-driven medical robots: An analytical magnetic model for endoscopic capsules design

Science.gov (United States)

Li, Jing; Barjuei, Erfan Shojaei; Ciuti, Gastone; Hao, Yang; Zhang, Peisen; Menciassi, Arianna; Huang, Qiang; Dario, Paolo

2018-04-01

Magnetic-based approaches are highly promising to provide innovative solutions for the design of medical devices for diagnostic and therapeutic procedures, such as in the endoluminal districts. Due to the intrinsic magnetic properties (no current needed) and the high strength-to-size ratio compared with electromagnetic solutions, permanent magnets are usually embedded in medical devices. In this paper, a set of analytical formulas have been derived to model the magnetic forces and torques which are exerted by an arbitrary external magnetic field on a permanent magnetic source embedded in a medical robot. In particular, the authors modelled cylindrical permanent magnets as general solution often used and embedded in magnetically-driven medical devices. The analytical model can be applied to axially and diametrically magnetized, solid and annular cylindrical permanent magnets in the absence of the severe calculation complexity. Using a cylindrical permanent magnet as a selected solution, the model has been applied to a robotic endoscopic capsule as a pilot study in the design of magnetically-driven robots.

Agent-based modeling of sustainable behaviors

CERN Document Server

Sánchez-Maroño, Noelia; Fontenla-Romero, Oscar; Polhill, J; Craig, Tony; Bajo, Javier; Corchado, Juan

2017-01-01

Using the O.D.D. (Overview, Design concepts, Detail) protocol, this title explores the role of agent-based modeling in predicting the feasibility of various approaches to sustainability. The chapters incorporated in this volume consist of real case studies to illustrate the utility of agent-based modeling and complexity theory in discovering a path to more efficient and sustainable lifestyles. The topics covered within include: households' attitudes toward recycling, designing decision trees for representing sustainable behaviors, negotiation-based parking allocation, auction-based traffic signal control, and others. This selection of papers will be of interest to social scientists who wish to learn more about agent-based modeling as well as experts in the field of agent-based modeling.

Surface-based geometric modelling using teaching trees for advanced robots

International Nuclear Information System (INIS)

Nakamura, Akira; Ogasawara, Tsukasa; Tsukune, Hideo; Oshima, Masaki

2000-01-01

Geometric modelling of the environment is important in robot motion planning. Generally, shapes can be stored in a data base, so the elements that need to be decided are positions and orientations. In this paper, surface-based geometric modelling using a teaching tree is proposed. In this modelling, combinations of surfaces are considered in order to decide positions and orientations of objects. The combinations are represented by a depth-first tree, which makes it easy for the operator to select one combination out of several. This method is effective not only in the case when perfect data can be obtained, but also when conditions for measurement of three-dimensional data are unfavorable, which often occur in the environment of a working robot. (author)

Modeling and Control of Underwater Robotic Systems

Energy Technology Data Exchange (ETDEWEB)

Schjoelberg, I:

1996-12-31

This doctoral thesis describes modeling and control of underwater vehicle-manipulator systems. The thesis also presents a model and a control scheme for a system consisting of a surface vessel connected to an underwater robotic system by means of a slender marine structure. The equations of motion of the underwater vehicle and manipulator are described and the system kinematics and properties presented. Feedback linearization technique is applied to the system and evaluated through a simulation study. Passivity-based controllers for vehicle and manipulator control are presented. Stability of the closed loop system is proved and simulation results are given. The equation of motion for lateral motion of a cable/riser system connected to a surface vessel at the top end and to a thruster at the bottom end is described and stability analysis and simulations are presented. The equations of motion in 3 degrees of freedom of the cable/riser, surface vessel and robotic system are given. Stability analysis of the total system with PD-controllers is presented. 47 refs., 32 figs., 7 tabs.

Project ROBOTICS 2008

DEFF Research Database (Denmark)

Conrad, Finn

Mathematical modelling of Alto Robot, direct- and inverse kinematic transformation,simulation and path control applying MATLAB/SIMULINK.......Mathematical modelling of Alto Robot, direct- and inverse kinematic transformation,simulation and path control applying MATLAB/SIMULINK....

Imprecise Beliefs in a Principal Agent Model

NARCIS (Netherlands)

Rigotti, L.

1998-01-01

This paper presents a principal-agent model where the agent has multiple, or imprecise, beliefs. We model this situation formally by assuming the agent's preferences are incomplete. One can interpret this multiplicity as an agent's limited knowledge of the surrounding environment. In this setting,

Comparative Study of SSVEP- and P300-Based Models for the Telepresence Control of Humanoid Robots.

Directory of Open Access Journals (Sweden)

Jing Zhao

Full Text Available In this paper, we evaluate the control performance of SSVEP (steady-state visual evoked potential- and P300-based models using Cerebot-a mind-controlled humanoid robot platform. Seven subjects with diverse experience participated in experiments concerning the open-loop and closed-loop control of a humanoid robot via brain signals. The visual stimuli of both the SSVEP- and P300- based models were implemented on a LCD computer monitor with a refresh frequency of 60 Hz. Considering the operation safety, we set the classification accuracy of a model over 90.0% as the most important mandatory for the telepresence control of the humanoid robot. The open-loop experiments demonstrated that the SSVEP model with at most four stimulus targets achieved the average accurate rate about 90%, whereas the P300 model with the six or more stimulus targets under five repetitions per trial was able to achieve the accurate rates over 90.0%. Therefore, the four SSVEP stimuli were used to control four types of robot behavior; while the six P300 stimuli were chosen to control six types of robot behavior. Both of the 4-class SSVEP and 6-class P300 models achieved the average success rates of 90.3% and 91.3%, the average response times of 3.65 s and 6.6 s, and the average information transfer rates (ITR of 24.7 bits/min 18.8 bits/min, respectively. The closed-loop experiments addressed the telepresence control of the robot; the objective was to cause the robot to walk along a white lane marked in an office environment using live video feedback. Comparative studies reveal that the SSVEP model yielded faster response to the subject's mental activity with less reliance on channel selection, whereas the P300 model was found to be suitable for more classifiable targets and required less training. To conclude, we discuss the existing SSVEP and P300 models for the control of humanoid robots, including the models proposed in this paper.

Nonlinear Model Predictive Control of a Cable-Robot-Based Motion Simulator

DEFF Research Database (Denmark)

Katliar, Mikhail; Fischer, Joerg; Frison, Gianluca

2017-01-01

In this paper we present the implementation of a model-predictive controller (MPC) for real-time control of a cable-robot-based motion simulator. The controller computes control inputs such that a desired acceleration and angular velocity at a defined point in simulator's cabin are tracked while...... satisfying constraints imposed by working space and allowed cable forces of the robot. In order to fully use the simulator capabilities, we propose an approach that includes the motion platform actuation in the MPC model. The tracking performance and computation time of the algorithm are investigated...

A Model Based Approach to Increase the Part Accuracy in Robot Based Incremental Sheet Metal Forming

International Nuclear Information System (INIS)

Meier, Horst; Laurischkat, Roman; Zhu Junhong

2011-01-01

One main influence on the dimensional accuracy in robot based incremental sheet metal forming results from the compliance of the involved robot structures. Compared to conventional machine tools the low stiffness of the robot's kinematic results in a significant deviation of the planned tool path and therefore in a shape of insufficient quality. To predict and compensate these deviations offline, a model based approach, consisting of a finite element approach, to simulate the sheet forming, and a multi body system, modeling the compliant robot structure, has been developed. This paper describes the implementation and experimental verification of the multi body system model and its included compensation method.

Modeling culture in intelligent virtual agents

OpenAIRE

Mascarenhas, S.; Degens, N.; Paiva, A.; Prada, R.; Hofstede, G.J.; Beulens, A.J.M.; Aylett, R.

2016-01-01

This work addresses the challenge of creating virtual agents that are able to portray culturally appropriate behavior when interacting with other agents or humans. Because culture influences how people perceive their social reality it is important to have agent models that explicitly consider social elements, such as existing relational factors. We addressed this necessity by integrating culture into a novel model for simulating human social behavior. With this model, we operationalized a par...

Automatic Modeling and Simulation of Modular Robots

Science.gov (United States)

Jiang, C.; Wei, H.; Zhang, Y.

2018-03-01

The ability of reconfiguration makes modular robots have the ability of adaptable, low-cost, self-healing and fault-tolerant. It can also be applied to a variety of mission situations. In this manuscript, a robot platform which relied on the module library was designed, based on the screw theory and module theory. Then, the configuration design method of the modular robot was proposed. And the different configurations of modular robot system have been built, including industrial mechanical arms, the mobile platform, six-legged robot and 3D exoskeleton manipulator. Finally, the simulation and verification of one system among them have been made, using the analyses of screw kinematics and polynomial planning. The results of experiments demonstrate the feasibility and superiority of this modular system.

The importance of shared mental models and shared situation awareness for transforming robots from tools to teammates

Science.gov (United States)

Ososky, Scott; Schuster, David; Jentsch, Florian; Fiore, Stephen; Shumaker, Randall; Lebiere, Christian; Kurup, Unmesh; Oh, Jean; Stentz, Anthony

2012-06-01

Current ground robots are largely employed via tele-operation and provide their operators with useful tools to extend reach, improve sensing, and avoid dangers. To move from robots that are useful as tools to truly synergistic human-robot teaming, however, will require not only greater technical capabilities among robots, but also a better understanding of the ways in which the principles of teamwork can be applied from exclusively human teams to mixed teams of humans and robots. In this respect, a core characteristic that enables successful human teams to coordinate shared tasks is their ability to create, maintain, and act on a shared understanding of the world and the roles of the team and its members in it. The team performance literature clearly points towards two important cornerstones for shared understanding of team members: mental models and situation awareness. These constructs have been investigated as products of teams as well; amongst teams, they are shared mental models and shared situation awareness. Consequently, we are studying how these two constructs can be measured and instantiated in human-robot teams. In this paper, we report results from three related efforts that are investigating process and performance outcomes for human robot teams. Our investigations include: (a) how human mental models of tasks and teams change whether a teammate is human, a service animal, or an advanced automated system; (b) how computer modeling can lead to mental models being instantiated and used in robots; (c) how we can simulate the interactions between human and future robotic teammates on the basis of changes in shared mental models and situation assessment.

Investigations Into Internal and External Aspects of Dynamic Agent-Environment Couplings

Science.gov (United States)

Dautenhahn, Kerstin

This paper originates from my work on `social agents'. An issue which I consider important to this kind of research is the dynamic coupling of an agent with its social and non-social environment. I hypothesize `internal dynamics' inside an agent as a basic step towards understanding. The paper therefore focuses on the internal and external dynamics which couple an agent to its environment. The issue of embodiment in animals and artifacts and its relation to `social dynamics' is discussed first. I argue that embodiment is linked to a concept of a body and is not necessarily given when running a control program on robot hardware. I stress the individual characteristics of an embodied cognitive system, as well as its social embeddedness. I outline the framework of a physical-psychological state space which changes dynamically in a self-modifying way as a holistic approach towards embodied human and artificial cognition. This framework is meant to discuss internal and external dynamics of an embodied, natural or artificial agent. In order to stress the importance of a dynamic memory I introduce the concept of an `autobiographical agent'. The second part of the paper gives an example of the implementation of a physical agent, a robot, which is dynamically coupled to its environment by balancing on a seesaw. For the control of the robot a behavior-oriented approach using the dynamical systems metaphor is used. The problem is studied through building a complete and co-adapted robot-environment system. A seesaw which varies its orientation with one or two degrees of freedom is used as the artificial `habitat'. The problem of stabilizing the body axis by active motion on a seesaw is solved by using two inclination sensors and a parallel, behavior-oriented control architecture. Some experiments are described which demonstrate the exploitation of the dynamics of the robot-environment system.

Kinematics modeling and experimentation of the multi-manipulator tooth-arrangement robot for full denture manufacturing.

Science.gov (United States)

Zhang, Yong-de; Jiang, Jin-gang; Liang, Ting; Hu, Wei-ping

2011-12-01

Artificial teeth are very complicated in shape, and not easy to be grasped and manipulated accurately by a single robot. The method of tooth-arrangement by multi-manipulator for complete denture manufacturing proposed in this paper. A novel complete denture manufacturing mechanism is designed based on multi-manipulator and dental arch generator. Kinematics model of the multi-manipulator tooth-arrangement robot is built by analytical method based on tooth-arrangement principle for full denture. Preliminary experiments on tooth-arrangement are performed using the multi-manipulator tooth-arrangement robot prototype system. The multi-manipulator tooth-arrangement robot prototype system can automatically design and manufacture a set of complete denture that is suitable for a patient according to the jaw arch parameters. The experimental results verified the validity of kinematics model of the multi-manipulator tooth-arrangement robot and the feasibility of the manufacture strategy of complete denture fulfilled by multi-manipulator tooth-arrangement robot.

Functional Modeling for Monitoring of Robotic System

DEFF Research Database (Denmark)

Wu, Haiyan; Bateman, Rikke R.; Zhang, Xinxin

2018-01-01

With the expansion of robotic applications in the industrial domain, it is important that the robots can execute their tasks in a safe and reliable way. A monitoring system can be implemented to ensure the detection of abnormal situations of the robots and report the abnormality to their human su...

An innovative approach for modeling and simulation of an automated industrial robotic arm operated electro-pneumatically

Science.gov (United States)

Popa, L.; Popa, V.

2017-08-01

The article is focused on modeling an automated industrial robotic arm operated electro-pneumatically and to simulate the robotic arm operation. It is used the graphic language FBD (Function Block Diagram) to program the robotic arm on Zelio Logic automation. The innovative modeling and simulation procedures are considered specific problems regarding the development of a new type of technical products in the field of robotics. Thus, were identified new applications of a Programmable Logic Controller (PLC) as a specialized computer performing control functions with a variety of high levels of complexit.

Exploring cultural factors in human-robot interaction : A matter of personality?

NARCIS (Netherlands)

Weiss, Astrid; Evers, Vanessa

2011-01-01

This paper proposes an experimental study to investigate task-dependence and cultural-background dependence of the personality trait attribution on humanoid robots. In Human-Robot Interaction, as well as in Human-Agent Interaction research, the attribution of personality traits towards intelligent

Anthropomorphism in Human-Robot Co-evolution.

Science.gov (United States)

Damiano, Luisa; Dumouchel, Paul

2018-01-01

Social robotics entertains a particular relationship with anthropomorphism, which it neither sees as a cognitive error, nor as a sign of immaturity. Rather it considers that this common human tendency, which is hypothesized to have evolved because it favored cooperation among early humans, can be used today to facilitate social interactions between humans and a new type of cooperative and interactive agents - social robots. This approach leads social robotics to focus research on the engineering of robots that activate anthropomorphic projections in users. The objective is to give robots "social presence" and "social behaviors" that are sufficiently credible for human users to engage in comfortable and potentially long-lasting relations with these machines. This choice of 'applied anthropomorphism' as a research methodology exposes the artifacts produced by social robotics to ethical condemnation: social robots are judged to be a "cheating" technology, as they generate in users the illusion of reciprocal social and affective relations. This article takes position in this debate, not only developing a series of arguments relevant to philosophy of mind, cognitive sciences, and robotic AI, but also asking what social robotics can teach us about anthropomorphism. On this basis, we propose a theoretical perspective that characterizes anthropomorphism as a basic mechanism of interaction, and rebuts the ethical reflections that a priori condemns "anthropomorphism-based" social robots. To address the relevant ethical issues, we promote a critical experimentally based ethical approach to social robotics, "synthetic ethics," which aims at allowing humans to use social robots for two main goals: self-knowledge and moral growth.

Designing and implementing transparency for real time inspection of autonomous robots

Science.gov (United States)

Theodorou, Andreas; Wortham, Robert H.; Bryson, Joanna J.

2017-07-01

The EPSRC's Principles of Robotics advises the implementation of transparency in robotic systems, however research related to AI transparency is in its infancy. This paper introduces the reader of the importance of having transparent inspection of intelligent agents and provides guidance for good practice when developing such agents. By considering and expanding upon other prominent definitions found in literature, we provide a robust definition of transparency as a mechanism to expose the decision-making of a robot. The paper continues by addressing potential design decisions developers need to consider when designing and developing transparent systems. Finally, we describe our new interactive intelligence editor, designed to visualise, develop and debug real-time intelligence.

Real-Time Motion Planning and Safe Navigation in Dynamic Multi-Robot Environments

National Research Council Canada - National Science Library

Bruce, James R

2006-01-01

.... While motion planning has been used for high level robot navigation, or limited to semi-static or single-robot domains, it has often been dismissed for the real-time low-level control of agents due...

A bio-inspired swarm robot coordination algorithm for multiple target searching

Science.gov (United States)

Meng, Yan; Gan, Jing; Desai, Sachi

2008-04-01

The coordination of a multi-robot system searching for multi targets is challenging under dynamic environment since the multi-robot system demands group coherence (agents need to have the incentive to work together faithfully) and group competence (agents need to know how to work together well). In our previous proposed bio-inspired coordination method, Local Interaction through Virtual Stigmergy (LIVS), one problem is the considerable randomness of the robot movement during coordination, which may lead to more power consumption and longer searching time. To address these issues, an adaptive LIVS (ALIVS) method is proposed in this paper, which not only considers the travel cost and target weight, but also predicting the target/robot ratio and potential robot redundancy with respect to the detected targets. Furthermore, a dynamic weight adjustment is also applied to improve the searching performance. This new method a truly distributed method where each robot makes its own decision based on its local sensing information and the information from its neighbors. Basically, each robot only communicates with its neighbors through a virtual stigmergy mechanism and makes its local movement decision based on a Particle Swarm Optimization (PSO) algorithm. The proposed ALIVS algorithm has been implemented on the embodied robot simulator, Player/Stage, in a searching target. The simulation results demonstrate the efficiency and robustness in a power-efficient manner with the real-world constraints.

Agent-Based Models in Social Physics

Science.gov (United States)

Quang, Le Anh; Jung, Nam; Cho, Eun Sung; Choi, Jae Han; Lee, Jae Woo

2018-06-01

We review the agent-based models (ABM) on social physics including econophysics. The ABM consists of agent, system space, and external environment. The agent is autonomous and decides his/her behavior by interacting with the neighbors or the external environment with the rules of behavior. Agents are irrational because they have only limited information when they make decisions. They adapt using learning from past memories. Agents have various attributes and are heterogeneous. ABM is a non-equilibrium complex system that exhibits various emergence phenomena. The social complexity ABM describes human behavioral characteristics. In ABMs of econophysics, we introduce the Sugarscape model and the artificial market models. We review minority games and majority games in ABMs of game theory. Social flow ABM introduces crowding, evacuation, traffic congestion, and pedestrian dynamics. We also review ABM for opinion dynamics and voter model. We discuss features and advantages and disadvantages of Netlogo, Repast, Swarm, and Mason, which are representative platforms for implementing ABM.

Using insects to drive mobile robots - hybrid robots bridge the gap between biological and artificial systems.

Science.gov (United States)

Ando, Noriyasu; Kanzaki, Ryohei

2017-09-01

The use of mobile robots is an effective method of validating sensory-motor models of animals in a real environment. The well-identified insect sensory-motor systems have been the major targets for modeling. Furthermore, mobile robots implemented with such insect models attract engineers who aim to avail advantages from organisms. However, directly comparing the robots with real insects is still difficult, even if we successfully model the biological systems, because of the physical differences between them. We developed a hybrid robot to bridge the gap. This hybrid robot is an insect-controlled robot, in which a tethered male silkmoth (Bombyx mori) drives the robot in order to localize an odor source. This robot has the following three advantages: 1) from a biomimetic perspective, the robot enables us to evaluate the potential performance of future insect-mimetic robots; 2) from a biological perspective, the robot enables us to manipulate the closed-loop of an onboard insect for further understanding of its sensory-motor system; and 3) the robot enables comparison with insect models as a reference biological system. In this paper, we review the recent works regarding insect-controlled robots and discuss the significance for both engineering and biology. Copyright © 2017 Elsevier Ltd. All rights reserved.

Colias: An Autonomous Micro Robot for Swarm Robotic Applications

Directory of Open Access Journals (Sweden)

Farshad Arvin

2014-07-01

Full Text Available Robotic swarms that take inspiration from nature are becoming a fascinating topic for multi-robot researchers. The aim is to control a large number of simple robots in order to solve common complex tasks. Due to the hardware complexities and cost of robot platforms, current research in swarm robotics is mostly performed by simulation software. The simulation of large numbers of these robots in robotic swarm applications is extremely complex and often inaccurate due to the poor modelling of external conditions. In this paper, we present the design of a low-cost, open-platform, autonomous micro-robot (Colias for robotic swarm applications. Colias employs a circular platform with a diameter of 4 cm. It has a maximum speed of 35 cm/s which enables it to be used in swarm scenarios very quickly over large arenas. Long-range infrared modules with an adjustable output power allow the robot to communicate with its direct neighbours at a range of 0.5 cm to 2 m. Colias has been designed as a complete platform with supporting software development tools for robotics education and research. It has been tested in both individual and swarm scenarios, and the observed results demonstrate its feasibility for use as a micro-sized mobile robot and as a low-cost platform for robot swarm applications.

A receptionist robot for Brazilian people: study on interaction involving illiterates

Directory of Open Access Journals (Sweden)

Trovato Gabriele

2017-04-01

Full Text Available The receptionist job, consisting in providing useful indications to visitors in a public office, is one possible employment of social robots. The design and the behaviour of robots expected to be integrated in human societies are crucial issues, and they are dependent on the culture and society in which the robot should be deployed. We study the factors that could be used in the design of a receptionist robot in Brazil, a country with a mix of races and considerable gaps in economic and educational level. This inequality results in the presence of functional illiterate people, unable to use reading, writing and numeracy skills. We invited Brazilian people, including a group of functionally illiterate subjects, to interact with two types of receptionists differing in physical appearance (agent v mechanical robot and in the sound of the voice (human like v mechanical. Results gathered during the interactions point out a preference for the agent, for the human-like voice and a more intense reaction to stimuli by illiterates. These results provide useful indications that should be considered when designing a receptionist robot, as well as insights on the effect of illiteracy in the interaction.

Grounding action words in the sensorimotor interaction with the world: experiments with a simulated iCub humanoid robot

Directory of Open Access Journals (Sweden)

Davide Marocco

2010-05-01

Full Text Available This paper presents a cognitive robotics model for the study of the embodied representation of action words. The present research will present how a iCub humanoid robot can learn the meaning of action words (i.e. words that represent dynamical events that happen in time by physically acting on the environment and linking the effects of its own actions with the behaviour observed on the objects before and after the action. The control system of the robot is an artificial neural network trained to manipulate an object through a Back-Propagation Through Time algorithm. We will show that in the presented model the grounding of action words relies directly to the way in which an agent interacts with the environment and manipulates it.

Emotional Storytelling using Virtual and Robotic Agents

OpenAIRE

Costa, Sandra; Brunete, Alberto; Bae, Byung-Chull; Mavridis, Nikolaos

2016-01-01

In order to create effective storytelling agents three fundamental questions must be answered: first, is a physically embodied agent preferable to a virtual agent or a voice-only narration? Second, does a human voice have an advantage over a synthesised voice? Third, how should the emotional trajectory of the different characters in a story be related to a storyteller's facial expressions during storytelling time, and how does this correlate with the apparent emotions on the faces of the list...

Comparison of Communication Models for Mobile Agents

Directory of Open Access Journals (Sweden)

Xining Li

2003-04-01

Full Text Available An agent is a self-contained process being acting on behalf of a user. A Mobile Agent is an agent roaming the internet to access data and services, and carry out its assigned task remotely. This paper will focus on the communication models for Mobile Agents. Generally speaking, communication models concern with problems of how to name Mobile Agents, how to establish communication relationships, how to trace moving agents, and how to guarantee reliable communication. Some existing MA systems are purely based on RPC-style communication, whereas some adopts asynchronous message passing, or event registration/handling. Different communication concepts suitable for Mobile Agents are well discussed in [1]. However, we will investigate these concepts and existing models from a different point view: how to track down agents and deliver messages in a dynamic, changing world.

Model and Behavior-Based Robotic Goalkeeper

DEFF Research Database (Denmark)

Lausen, H.; Nielsen, J.; Nielsen, M.

2003-01-01

This paper describes the design, implementation and test of a goalkeeper robot for the Middle-Size League of RoboCub. The goalkeeper task is implemented by a set of primitive tasks and behaviours coordinated by a 2-level hierarchical state machine. The primitive tasks concerning complex motion...... control are implemented by a non-linear control algorithm, adapted to the different task goals (e.g., follow the ball or the robot posture from local features extracted from images acquired by a catadioptric omni-directional vision system. Most robot parameters were designed based on simulations carried...

Affordances for robots: a brief survey

Directory of Open Access Journals (Sweden)

Thomas E. Horton

2012-12-01

Full Text Available In this paper, we consider the influence of Gibson's affordance theory on the design of robotic agents. Affordance theory (and the ecological approach to agent design in general has in many cases contributed to the development of successful robotic systems; we provide a brief survey of AI research in this area. However, there remain significant issues that complicate discussions on this topic, particularly in the exchange of ideas between researchers in artificial intelligence and ecological psychology. We identify some of these issues, specifically the lack of a generally accepted definition of "affordance" and fundamental differences in the current approaches taken in AI and ecological psychology. While we consider reconciliation between these fields to be possible and mutually beneficial, it will require some flexibility on the issue of direct perception.

Modeling Leadership Styles in Human-Robot Team Dynamics

Science.gov (United States)

Cruz, Gerardo E.

2005-01-01

The recent proliferation of robotic systems in our society has placed questions regarding interaction between humans and intelligent machines at the forefront of robotics research. In response, our research attempts to understand the context in which particular types of interaction optimize efficiency in tasks undertaken by human-robot teams. It is our conjecture that applying previous research results regarding leadership paradigms in human organizations will lead us to a greater understanding of the human-robot interaction space. In doing so, we adapt four leadership styles prevalent in human organizations to human-robot teams. By noting which leadership style is more appropriately suited to what situation, as given by previous research, a mapping is created between the adapted leadership styles and human-robot interaction scenarios-a mapping which will presumably maximize efficiency in task completion for a human-robot team. In this research we test this mapping with two adapted leadership styles: directive and transactional. For testing, we have taken a virtual 3D interface and integrated it with a genetic algorithm for use in &le-operation of a physical robot. By developing team efficiency metrics, we can determine whether this mapping indeed prescribes interaction styles that will maximize efficiency in the teleoperation of a robot.

A CSP-Based Agent Modeling Framework for the Cougaar Agent-Based Architecture

Science.gov (United States)

Gracanin, Denis; Singh, H. Lally; Eltoweissy, Mohamed; Hinchey, Michael G.; Bohner, Shawn A.

2005-01-01

Cognitive Agent Architecture (Cougaar) is a Java-based architecture for large-scale distributed agent-based applications. A Cougaar agent is an autonomous software entity with behaviors that represent a real-world entity (e.g., a business process). A Cougaar-based Model Driven Architecture approach, currently under development, uses a description of system's functionality (requirements) to automatically implement the system in Cougaar. The Communicating Sequential Processes (CSP) formalism is used for the formal validation of the generated system. Two main agent components, a blackboard and a plugin, are modeled as CSP processes. A set of channels represents communications between the blackboard and individual plugins. The blackboard is represented as a CSP process that communicates with every agent in the collection. The developed CSP-based Cougaar modeling framework provides a starting point for a more complete formal verification of the automatically generated Cougaar code. Currently it is used to verify the behavior of an individual agent in terms of CSP properties and to analyze the corresponding Cougaar society.

Robotic Motion Learning Framework to Promote Social Engagement

Directory of Open Access Journals (Sweden)

Rachael Burns

2018-02-01

Full Text Available Imitation is a powerful component of communication between people, and it poses an important implication in improving the quality of interaction in the field of human–robot interaction (HRI. This paper discusses a novel framework designed to improve human–robot interaction through robotic imitation of a participant’s gestures. In our experiment, a humanoid robotic agent socializes with and plays games with a participant. For the experimental group, the robot additionally imitates one of the participant’s novel gestures during a play session. We hypothesize that the robot’s use of imitation will increase the participant’s openness towards engaging with the robot. Experimental results from a user study of 12 subjects show that post-imitation, experimental subjects displayed a more positive emotional state, had higher instances of mood contagion towards the robot, and interpreted the robot to have a higher level of autonomy than their control group counterparts did. These results point to an increased participant interest in engagement fueled by personalized imitation during interaction.

Soft object deformation monitoring and learning for model-based robotic hand manipulation.

Science.gov (United States)

Cretu, Ana-Maria; Payeur, Pierre; Petriu, Emil M

2012-06-01

This paper discusses the design and implementation of a framework that automatically extracts and monitors the shape deformations of soft objects from a video sequence and maps them with force measurements with the goal of providing the necessary information to the controller of a robotic hand to ensure safe model-based deformable object manipulation. Measurements corresponding to the interaction force at the level of the fingertips and to the position of the fingertips of a three-finger robotic hand are associated with the contours of a deformed object tracked in a series of images using neural-network approaches. The resulting model captures the behavior of the object and is able to predict its behavior for previously unseen interactions without any assumption on the object's material. The availability of such models can contribute to the improvement of a robotic hand controller, therefore allowing more accurate and stable grasp while providing more elaborate manipulation capabilities for deformable objects. Experiments performed for different objects, made of various materials, reveal that the method accurately captures and predicts the object's shape deformation while the object is submitted to external forces applied by the robot fingers. The proposed method is also fast and insensitive to severe contour deformations, as well as to smooth changes in lighting, contrast, and background.

Toward understanding social cues and signals in human–robot interaction: effects of robot gaze and proxemic behavior

Science.gov (United States)

Fiore, Stephen M.; Wiltshire, Travis J.; Lobato, Emilio J. C.; Jentsch, Florian G.; Huang, Wesley H.; Axelrod, Benjamin

2013-01-01

As robots are increasingly deployed in settings requiring social interaction, research is needed to examine the social signals perceived by humans when robots display certain social cues. In this paper, we report a study designed to examine how humans interpret social cues exhibited by robots. We first provide a brief overview of perspectives from social cognition in humans and how these processes are applicable to human–robot interaction (HRI). We then discuss the need to examine the relationship between social cues and signals as a function of the degree to which a robot is perceived as a socially present agent. We describe an experiment in which social cues were manipulated on an iRobot AvaTM mobile robotics platform in a hallway navigation scenario. Cues associated with the robot’s proxemic behavior were found to significantly affect participant perceptions of the robot’s social presence and emotional state while cues associated with the robot’s gaze behavior were not found to be significant. Further, regardless of the proxemic behavior, participants attributed more social presence and emotional states to the robot over repeated interactions than when they first interacted with it. Generally, these results indicate the importance for HRI research to consider how social cues expressed by a robot can differentially affect perceptions of the robot’s mental states and intentions. The discussion focuses on implications for the design of robotic systems and future directions for research on the relationship between social cues and signals. PMID:24348434

Towards understanding social cues and signals in human-robot interaction: Effects of robot gaze and proxemic behavior

Directory of Open Access Journals (Sweden)

Stephen M. Fiore

2013-11-01

Full Text Available As robots are increasingly deployed in settings requiring social interaction, research is needed to examine the social signals perceived by humans when robots display certain social cues. In this paper, we report a study designed to examine how humans interpret social cues exhibited by robots. We first provide a brief overview of perspectives from social cognition in humans and how these processes are applicable to human-robot interaction (HRI. We then discuss the need to examine the relationship between social cues and signals as a function of the degree to which a robot is perceived as a socially present agent. We describe an experiment in which social cues were manipulated on an iRobot Ava™ Mobile Robotics Platform in a hallway navigation scenario. Cues associated with the robot’s proxemic behavior were found to significantly affect participant perceptions of the robot’s social presence and emotional state while cues associated with the robot’s gaze behavior were not found to be significant. Further, regardless of the proxemic behavior, participants attributed more social presence and emotional states to the robot over repeated interactions than when they first interacted with it. Generally, these results indicate the importance for HRI research to consider how social cues expressed by a robot can differentially affect perceptions of the robot’s mental states and intentions. The discussion focuses on implications for the design of robotic systems and future directions for research on the relationship between social cues and signals.

Conceptions of health service robots

DEFF Research Database (Denmark)

Lystbæk, Christian Tang

2015-01-01

Technology developments create rich opportunities for health service providers to introduce service robots in health care. While the potential benefits of applying robots in health care are extensive, the research into the conceptions of health service robot and its importance for the uptake...... of robotics technology in health care is limited. This article develops a model of the basic conceptions of health service robots that can be used to understand different assumptions and values attached to health care technology in general and health service robots in particular. The article takes...... a discursive approach in order to develop a conceptual framework for understanding the social values of health service robots. First a discursive approach is proposed to develop a typology of conceptions of health service robots. Second, a model identifying four basic conceptions of health service robots...

Movement Performance of Human-Robot Cooperation Control Based on EMG-Driven Hill-Type and Proportional Models for an Ankle Power-Assist Exoskeleton Robot.

Science.gov (United States)

Ao, Di; Song, Rong; Gao, JinWu

2017-08-01

Although the merits of electromyography (EMG)-based control of powered assistive systems have been certified, the factors that affect the performance of EMG-based human-robot cooperation, which are very important, have received little attention. This study investigates whether a more physiologically appropriate model could improve the performance of human-robot cooperation control for an ankle power-assist exoskeleton robot. To achieve the goal, an EMG-driven Hill-type neuromusculoskeletal model (HNM) and a linear proportional model (LPM) were developed and calibrated through maximum isometric voluntary dorsiflexion (MIVD). The two control models could estimate the real-time ankle joint torque, and HNM is more accurate and can account for the change of the joint angle and muscle dynamics. Then, eight healthy volunteers were recruited to wear the ankle exoskeleton robot and complete a series of sinusoidal tracking tasks in the vertical plane. With the various levels of assist based on the two calibrated models, the subjects were instructed to track the target displayed on the screen as accurately as possible by performing ankle dorsiflexion and plantarflexion. Two measurements, the root mean square error (RMSE) and root mean square jerk (RMSJ), were derived from the assistant torque and kinematic signals to characterize the movement performances, whereas the amplitudes of the recorded EMG signals from the tibialis anterior (TA) and the gastrocnemius (GAS) were obtained to reflect the muscular efforts. The results demonstrated that the muscular effort and smoothness of tracking movements decreased with an increase in the assistant ratio. Compared with LPM, subjects made lower physical efforts and generated smoother movements when using HNM, which implied that a more physiologically appropriate model could enable more natural and human-like human-robot cooperation and has potential value for improvement of human-exoskeleton interaction in future applications.

New Methods for Kinematic Modelling and Calibration of Robots

DEFF Research Database (Denmark)

Søe-Knudsen, Rune

2014-01-01

the accuracy in an easy and accessible way. The required equipment is accessible, since the cost is held to a minimum and can be made with conventional processing equipment. Our first method calibrates the kinematics of a robot using known relative positions measured with the robot itself and a plate...... with holes matching the robot tool flange. The second method calibrates the kinematics using two robots. This method allows the robots to carry out the collection of measurements and the adjustment, by themselves, after the robots have been connected. Furthermore, we also propose a method for restoring......Improving a robot's accuracy increases its ability to solve certain tasks, and is therefore valuable. Practical ways of achieving this improved accuracy, even after robot repair, is also valuable. In this work, we introduce methods that improve the robot's accuracy and make it possible to maintain...

Drilling Load Model of an Inchworm Boring Robot for Lunar Subsurface Exploration

Directory of Open Access Journals (Sweden)

Weiwei Zhang

2017-01-01

Full Text Available In the past decade, the wireline robot has received increasing attention due to the advantages of light weight, low cost, and flexibility compared to the traditional drilling instruments in space missions. For the lunar subsurface in situ exploration mission, we proposed a type of wireline robot named IBR (Inchworm Boring Robot drawing inspiration from the inchworm. Two auger tools are utilized to remove chips for IBR, which directly interacted with the lunar regolith in the drilling process. Therefore, for obtaining the tools drilling characteristics, the chips removal principle of IBR is analyzed and its drilling load model is further established based on the soil mechanical theory in this paper. And then the proposed theoretical drilling load model is experimentally validated. In addition, according to the theoretical drilling load model, this paper discusses the effect of the drilling parameters on the tools drilling moments and power consumption. These results imply a possible energy-efficient control strategy for IBR.

Multibody system dynamics, robotics and control

CERN Document Server

Gerstmayr, Johannes

2013-01-01

The volume contains 19 contributions by international experts in the field of multibody system dynamics, robotics and control. The book aims to bridge the gap between the modeling of mechanical systems by means of multibody dynamics formulations and robotics. In the classical approach, a multibody dynamics model contains a very high level of detail, however, the application of such models to robotics or control is usually limited. The papers aim to connect the different scientific communities in multibody dynamics, robotics and control. Main topics are flexible multibody systems, humanoid robots, elastic robots, nonlinear control, optimal path planning, and identification.

Performance comparison of novel WNN approach with RBFNN in navigation of autonomous mobile robotic agent

Directory of Open Access Journals (Sweden)

Ghosh Saradindu

2016-01-01

Full Text Available This paper addresses the performance comparison of Radial Basis Function Neural Network (RBFNN with novel Wavelet Neural Network (WNN of designing intelligent controllers for path planning of mobile robot in an unknown environment. In the proposed WNN, different types of activation functions such as Mexican Hat, Gaussian and Morlet wavelet functions are used in the hidden nodes. The neural networks are trained by an intelligent supervised learning technique so that the robot makes a collision-free path in the unknown environment during navigation from different starting points to targets/goals. The efficiency of two algorithms is compared using some MATLAB simulations and experimental setup with Arduino Mega 2560 microcontroller in terms of path length and time taken to reach the target as an indicator for the accuracy of the network models.

Robot Control Overview: An Industrial Perspective

Directory of Open Access Journals (Sweden)

T. Brogårdh

2009-07-01

Full Text Available One key competence for robot manufacturers is robot control, defined as all the technologies needed to control the electromechanical system of an industrial robot. By means of modeling, identification, optimization, and model-based control it is possible to reduce robot cost, increase robot performance, and solve requirements from new automation concepts and new application processes. Model-based control, including kinematics error compensation, optimal servo reference- and feed-forward generation, and servo design, tuning, and scheduling, has meant a breakthrough for the use of robots in industry. Relying on this breakthrough, new automation concepts such as high performance multi robot collaboration and human robot collaboration can be introduced. Robot manufacturers can build robots with more compliant components and mechanical structures without loosing performance and robots can be used also in applications with very high performance requirements, e.g., in assembly, machining, and laser cutting. In the future it is expected that the importance of sensor control will increase, both with respect to sensors in the robot structure to increase the control performance of the robot itself and sensors outside the robot related to the applications and the automation systems. In this connection sensor fusion and learning functionalities will be needed together with the robot control for easy and intuitive installation, programming, and maintenance of industrial robots.

Hydraulic bilateral construction robot; Yuatsushiki bilateral kensetsu robot

Energy Technology Data Exchange (ETDEWEB)

Maehata, K.; Mori, N. [Kayaba Industry Co. Ltd., Tokyo (Japan)

1999-05-15

Concerning a hydraulic bilateral construction robot, its system constitution, structures and functions of important components, and the results of some tests are explained, and the researches conducted at Gifu University are described. The construction robot in this report is a servo controlled system of a version developed from the mini-shovel now available in the market. It is equipped, in addition to an electrohydraulic servo control system, with various sensors for detecting the robot attitude, vibration, and load state, and with a camera for visualizing the surrounding landscape. It is also provided with a bilateral joy stick which is a remote control actuator capable of working sensation feedback and with a rocking unit that creates robot movements of rolling, pitching, and heaving. The construction robot discussed here, with output increased and response faster thanks to the employment of a hydraulic driving system for the aim of building a robot system superior in performance to the conventional model designed primarily for heavy duty, proves after tests to be a highly sophisticated remotely controlled robot control system. (NEDO)

Cognitive Emotional Regulation Model in Human-Robot Interaction

OpenAIRE

Liu, Xin; Xie, Lun; Liu, Anqi; Li, Dan

2015-01-01

This paper integrated Gross cognitive process into the HMM (hidden Markov model) emotional regulation method and implemented human-robot emotional interaction with facial expressions and behaviors. Here, energy was the psychological driving force of emotional transition in the cognitive emotional model. The input facial expression was translated into external energy by expression-emotion mapping. Robot’s next emotional state was determined by the cognitive energy (the stimulus after cognition...

Autism and social robotics: A systematic review.

Science.gov (United States)

Pennisi, Paola; Tonacci, Alessandro; Tartarisco, Gennaro; Billeci, Lucia; Ruta, Liliana; Gangemi, Sebastiano; Pioggia, Giovanni

2016-02-01

Social robotics could be a promising method for Autism Spectrum Disorders (ASD) treatment. The aim of this article is to carry out a systematic literature review of the studies on this topic that were published in the last 10 years. We tried to address the following questions: can social robots be a useful tool in autism therapy? We followed the PRISMA guidelines, and the protocol was registered within PROSPERO database (CRD42015016158). We found many positive implications in the use of social robots in therapy as for example: ASD subjects often performed better with a robot partner rather than a human partner; sometimes, ASD patients had, toward robots, behaviors that TD patients had toward human agents; ASDs had a lot of social behaviors toward robots; during robotic sessions, ASDs showed reduced repetitive and stereotyped behaviors and, social robots manage to improve spontaneous language during therapy sessions. Therefore, robots provide therapists and researchers a means to connect with autistic subjects in an easier way, but studies in this area are still insufficient. It is necessary to clarify whether sex, intelligence quotient, and age of participants affect the outcome of therapy and whether any beneficial effects only occur during the robotic session or if they are still observable outside the clinical/experimental context. © 2015 International Society for Autism Research, Wiley Periodicals, Inc.

Anthropomorphism in Human–Robot Co-evolution

Directory of Open Access Journals (Sweden)

Luisa Damiano

2018-03-01

Full Text Available Social robotics entertains a particular relationship with anthropomorphism, which it neither sees as a cognitive error, nor as a sign of immaturity. Rather it considers that this common human tendency, which is hypothesized to have evolved because it favored cooperation among early humans, can be used today to facilitate social interactions between humans and a new type of cooperative and interactive agents – social robots. This approach leads social robotics to focus research on the engineering of robots that activate anthropomorphic projections in users. The objective is to give robots “social presence” and “social behaviors” that are sufficiently credible for human users to engage in comfortable and potentially long-lasting relations with these machines. This choice of ‘applied anthropomorphism’ as a research methodology exposes the artifacts produced by social robotics to ethical condemnation: social robots are judged to be a “cheating” technology, as they generate in users the illusion of reciprocal social and affective relations. This article takes position in this debate, not only developing a series of arguments relevant to philosophy of mind, cognitive sciences, and robotic AI, but also asking what social robotics can teach us about anthropomorphism. On this basis, we propose a theoretical perspective that characterizes anthropomorphism as a basic mechanism of interaction, and rebuts the ethical reflections that a priori condemns “anthropomorphism-based” social robots. To address the relevant ethical issues, we promote a critical experimentally based ethical approach to social robotics, “synthetic ethics,” which aims at allowing humans to use social robots for two main goals: self-knowledge and moral growth.

Anthropomorphism in Human–Robot Co-evolution

Science.gov (United States)

Damiano, Luisa; Dumouchel, Paul

2018-01-01

Social robotics entertains a particular relationship with anthropomorphism, which it neither sees as a cognitive error, nor as a sign of immaturity. Rather it considers that this common human tendency, which is hypothesized to have evolved because it favored cooperation among early humans, can be used today to facilitate social interactions between humans and a new type of cooperative and interactive agents – social robots. This approach leads social robotics to focus research on the engineering of robots that activate anthropomorphic projections in users. The objective is to give robots “social presence” and “social behaviors” that are sufficiently credible for human users to engage in comfortable and potentially long-lasting relations with these machines. This choice of ‘applied anthropomorphism’ as a research methodology exposes the artifacts produced by social robotics to ethical condemnation: social robots are judged to be a “cheating” technology, as they generate in users the illusion of reciprocal social and affective relations. This article takes position in this debate, not only developing a series of arguments relevant to philosophy of mind, cognitive sciences, and robotic AI, but also asking what social robotics can teach us about anthropomorphism. On this basis, we propose a theoretical perspective that characterizes anthropomorphism as a basic mechanism of interaction, and rebuts the ethical reflections that a priori condemns “anthropomorphism-based” social robots. To address the relevant ethical issues, we promote a critical experimentally based ethical approach to social robotics, “synthetic ethics,” which aims at allowing humans to use social robots for two main goals: self-knowledge and moral growth. PMID:29632507

Modelling reversible execution of robotic assembly

DEFF Research Database (Denmark)

Laursen, Johan Sund; Ellekilde, Lars Peter; Schultz, Ulrik Pagh

2018-01-01

Programming robotic assembly for industrial small-batch production is challenging; hence, it is vital to increase robustness and reduce development effort in order to achieve flexible robotic automation. A human who has made an assembly error will often simply undo the process until the error is ...

Robot fish bio-inspired fishlike underwater robots

CERN Document Server

Li, Zheng; Youcef-Toumi, Kamal; Alvarado, Pablo

2015-01-01

This book provides a comprehensive coverage on robot fish including design, modeling and optimization, control, autonomous control and applications. It gathers contributions by the leading researchers in the area. Readers will find the book very useful for designing and building robot fish, not only in theory but also in practice. Moreover, the book discusses various important issues for future research and development, including design methodology, control methodology, and autonomous control strategy. This book is intended for researchers and graduate students in the fields of robotics, ocean engineering and related areas.

Controlling Tensegrity Robots Through Evolution

Science.gov (United States)

Iscen, Atil; Agogino, Adrian; SunSpiral, Vytas; Tumer, Kagan

2013-01-01

Tensegrity structures (built from interconnected rods and cables) have the potential to offer a revolutionary new robotic design that is light-weight, energy-efficient, robust to failures, capable of unique modes of locomotion, impact tolerant, and compliant (reducing damage between the robot and its environment). Unfortunately robots built from tensegrity structures are difficult to control with traditional methods due to their oscillatory nature, nonlinear coupling between components and overall complexity. Fortunately this formidable control challenge can be overcome through the use of evolutionary algorithms. In this paper we show that evolutionary algorithms can be used to efficiently control a ball-shaped tensegrity robot. Experimental results performed with a variety of evolutionary algorithms in a detailed soft-body physics simulator show that a centralized evolutionary algorithm performs 400 percent better than a hand-coded solution, while the multi-agent evolution performs 800 percent better. In addition, evolution is able to discover diverse control solutions (both crawling and rolling) that are robust against structural failures and can be adapted to a wide range of energy and actuation constraints. These successful controls will form the basis for building high-performance tensegrity robots in the near future.

Generalized dynamic model and control of ambiguous mono axial vehicle robot

Directory of Open Access Journals (Sweden)

Frantisek Duchon

2016-09-01

Full Text Available This article deals with the novel concept of ambiguous mono axial vehicle robot. Such robot is a combination of Segway and dicycle, which utilizes the advantages of each chassis. The advantage of dicycle is lower energy consumption during the movement and the higher safety of carried payload. The movable platform inside the ambiguous mono axial vehicle allows using the various sensors or devices. This will change the ambiguous mono axial vehicle to the Segway type robot. Both these modes are necessary to control in the stable mode to ensure the safety of the ambiguous mono axial vehicle’s movement. The main contents of the article contain description of generalized dynamic model of ambiguous mono axial vehicle and related control of ambiguous mono axial vehicle. The proposal is unique in that the same controller is used for both modes. Several simulations verify proposed control schemes and identified parameters. Moreover, the dicycle type of platform has never been used in robotics and that is another novelty.

Modeling of welded bead profile for rapid prototyping by robotic MAG welding

Institute of Scientific and Technical Information of China (English)

CAO Yong; ZHU Sheng; WANG Tao; WANG Wanglong

2009-01-01

As a deposition technology, robotic metal active gas(MAG) welding has shown new promise for rapid prototyping (RP) of metallic parts. During the process of metal forming using robotic MAG welding, sectional profile of single-pass welded bead is critical to formed accuracy and quality of metal pans. In this paper, the experiments of single-pass welded bead for rapid prototyping using robotic MAG welding were carried out. The effect of some edge detectors on the cross-sectional edge of welded bead was discussed and curve fitting was applied using leat square fitting. Consequently, the mathematical model of welded bead profile was developed. The experimental results show that good shape could be obtained under suitable welding parameters. Canny operawr is suitable to edge detection of welded bead profile, and the mathematical model of welded bead profile developed is approximately parabola.

Analyzing the multiple-target-multiple-agent scenario using optimal assignment algorithms

Science.gov (United States)

Kwok, Kwan S.; Driessen, Brian J.; Phillips, Cynthia A.; Tovey, Craig A.

1997-09-01

This work considers the problem of maximum utilization of a set of mobile robots with limited sensor-range capabilities and limited travel distances. The robots are initially in random positions. A set of robots properly guards or covers a region if every point within the region is within the effective sensor range of at least one vehicle. We wish to move the vehicles into surveillance positions so as to guard or cover a region, while minimizing the maximum distance traveled by any vehicle. This problem can be formulated as an assignment problem, in which we must optimally decide which robot to assign to which slot of a desired matrix of grid points. The cost function is the maximum distance traveled by any robot. Assignment problems can be solved very efficiently. Solution times for one hundred robots took only seconds on a silicon graphics crimson workstation. The initial positions of all the robots can be sampled by a central base station and their newly assigned positions communicated back to the robots. Alternatively, the robots can establish their own coordinate system with the origin fixed at one of the robots and orientation determined by the compass bearing of another robot relative to this robot. This paper presents example solutions to the multiple-target-multiple-agent scenario using a matching algorithm. Two separate cases with one hundred agents in each were analyzed using this method. We have found these mobile robot problems to be a very interesting application of network optimization methods, and we expect this to be a fruitful area for future research.

Analyzing the multiple-target-multiple-agent scenario using optimal assignment algorithms

International Nuclear Information System (INIS)

Kwok, K.S.; Driessen, B.J.; Phillips, C.A.; Tovey, C.A.

1997-01-01

This work considers the problem of maximum utilization of a set of mobile robots with limited sensor-range capabilities and limited travel distances. The robots are initially in random positions. A set of robots properly guards or covers a region if every point within the region is within the effective sensor range of at least one vehicle. The authors wish to move the vehicles into surveillance positions so as to guard or cover a region, while minimizing the maximum distance traveled by any vehicle. This problem can be formulated as an assignment problem, in which they must optimally decide which robot to assign to which slot of a desired matrix of grid points. The cost function is the maximum distance traveled by any robot. Assignment problems can be solved very efficiently. Solutions times for one hundred robots took only seconds on a Silicon Graphics Crimson workstation. The initial positions of all the robots can be sampled by a central base station and their newly assigned positions communicated back to the robots. Alternatively, the robots can establish their own coordinate system with the origin fixed at one of the robots and orientation determined by the compass bearing of another robot relative to this robot. This paper presents example solutions to the multiple-target-multiple-agent scenario using a matching algorithm. Two separate cases with one hundred agents in each were analyzed using this method. They have found these mobile robot problems to be a very interesting application of network optimization methods, and they expect this to be a fruitful area for future research

Robotics and artificial intelligence for hazardous environments

International Nuclear Information System (INIS)

Spelt, P.F.

1993-01-01

In our technological society, hazardous materials including toxic chemicals, flammable, explosive, and radioactive substances, and biological agents, are used and handled routinely. Each year, many workers who handle these substances are accidently contaminated, in some cases resulting in injury, death, or chronic disabilities. If these hazardous materials could be handled remotely, either with a teleoperated robot (operated by a worker in a safe location) or by an autonomous robot, then human suffering and economic costs of accidental exposures could be dramatically reduced. At present, it is still difficult for commercial robotic technology to completely replace humans involved in performing complex work tasks in hazardous environments. The robotics efforts at the Center for Engineering Systems Advanced Research represent a significant effort at contributing to the advancement of robotics for use in hazardous environments. While this effort is very broad-based, ranging from dextrous manipulation to mobility and integrated sensing, the technical portion of this paper will focus on machine learning and the high-level decision making needed for autonomous robotics

Brain response to a humanoid robot in areas implicated in the perception of human emotional gestures.

Directory of Open Access Journals (Sweden)

Thierry Chaminade

2010-07-01

Full Text Available The humanoid robot WE4-RII was designed to express human emotions in order to improve human-robot interaction. We can read the emotions depicted in its gestures, yet might utilize different neural processes than those used for reading the emotions in human agents.Here, fMRI was used to assess how brain areas activated by the perception of human basic emotions (facial expression of Anger, Joy, Disgust and silent speech respond to a humanoid robot impersonating the same emotions, while participants were instructed to attend either to the emotion or to the motion depicted.Increased responses to robot compared to human stimuli in the occipital and posterior temporal cortices suggest additional visual processing when perceiving a mechanical anthropomorphic agent. In contrast, activity in cortical areas endowed with mirror properties, like left Broca's area for the perception of speech, and in the processing of emotions like the left anterior insula for the perception of disgust and the orbitofrontal cortex for the perception of anger, is reduced for robot stimuli, suggesting lesser resonance with the mechanical agent. Finally, instructions to explicitly attend to the emotion significantly increased response to robot, but not human facial expressions in the anterior part of the left inferior frontal gyrus, a neural marker of motor resonance.Motor resonance towards a humanoid robot, but not a human, display of facial emotion is increased when attention is directed towards judging emotions.Artificial agents can be used to assess how factors like anthropomorphism affect neural response to the perception of human actions.

Brain response to a humanoid robot in areas implicated in the perception of human emotional gestures.

Science.gov (United States)

Chaminade, Thierry; Zecca, Massimiliano; Blakemore, Sarah-Jayne; Takanishi, Atsuo; Frith, Chris D; Micera, Silvestro; Dario, Paolo; Rizzolatti, Giacomo; Gallese, Vittorio; Umiltà, Maria Alessandra

2010-07-21

The humanoid robot WE4-RII was designed to express human emotions in order to improve human-robot interaction. We can read the emotions depicted in its gestures, yet might utilize different neural processes than those used for reading the emotions in human agents. Here, fMRI was used to assess how brain areas activated by the perception of human basic emotions (facial expression of Anger, Joy, Disgust) and silent speech respond to a humanoid robot impersonating the same emotions, while participants were instructed to attend either to the emotion or to the motion depicted. Increased responses to robot compared to human stimuli in the occipital and posterior temporal cortices suggest additional visual processing when perceiving a mechanical anthropomorphic agent. In contrast, activity in cortical areas endowed with mirror properties, like left Broca's area for the perception of speech, and in the processing of emotions like the left anterior insula for the perception of disgust and the orbitofrontal cortex for the perception of anger, is reduced for robot stimuli, suggesting lesser resonance with the mechanical agent. Finally, instructions to explicitly attend to the emotion significantly increased response to robot, but not human facial expressions in the anterior part of the left inferior frontal gyrus, a neural marker of motor resonance. Motor resonance towards a humanoid robot, but not a human, display of facial emotion is increased when attention is directed towards judging emotions. Artificial agents can be used to assess how factors like anthropomorphism affect neural response to the perception of human actions.

Modelling of a biologically inspired robotic fish driven by compliant parts

International Nuclear Information System (INIS)

Daou, Hadi El; Salumäe, Taavi; Kruusmaa, Maarja; Chambers, Lily D; Megill, William M

2014-01-01

Inspired by biological swimmers such as fish, a robot composed of a rigid head, a compliant body and a rigid caudal fin was built. It has the geometrical properties of a subcarangiform swimmer of the same size. The head houses a servo-motor which actuates the compliant body and the caudal fin. It achieves this by applying a concentrated moment on a point near the compliant body base. In this paper, the dynamics of the compliant body driving the robotic fish is modelled and experimentally validated. Lighthill’s elongated body theory is used to define the hydrodynamic forces on the compliant part and Rayleigh proportional damping is used to model damping. Based on the assumed modes method, an energetic approach is used to write the equations of motion of the compliant body and to compute the relationship between the applied moment and the resulting lateral deflections. Experiments on the compliant body were carried out to validate the model predictions. The results showed that a good match was achieved between the measured and predicted deformations. A discussion of the swimming motions between the real fish and the robot is presented. (paper)

From responsible robotics towards a human rights regime oriented to the challenges of robotics and artificial intelligence

DEFF Research Database (Denmark)

Liu, Hin-Yan; Zawieska, Karolina

2017-01-01

impulse by proposing a complementary set of human rights directed specifically against the harms arising from robotic and artificial intelligence (AI) technologies. The relationship between responsibilities of the agent and the rights of the patient suggest that a rights regime is the other side...... to act responsibly. This subsists within a larger phenomenon where the difference between humans and non-humans, be it animals or artificial systems, appears to be increasingly blurred, thereby disrupting orthodox understandings of responsibility. This paper seeks to supplement the responsible robotics...

The Fourth Law of Robotics.

Science.gov (United States)

Markoff, John

1994-01-01

Discusses intelligent software agents, or knowledge robots (knowbots), and the impact they have on the Internet. Topics addressed include ethical dilemmas; problems created by rapid growth on the Internet; new technologies that are amplifying growth; and a shift to a market economy and resulting costs. (LRW)

Robot-based additive manufacturing for flexible die-modelling in incremental sheet forming

Science.gov (United States)

Rieger, Michael; Störkle, Denis Daniel; Thyssen, Lars; Kuhlenkötter, Bernd

2017-10-01

The paper describes the application concept of additive manufactured dies to support the robot-based incremental sheet metal forming process (`Roboforming') for the production of sheet metal components in small batch sizes. Compared to the dieless kinematic-based generation of a shape by means of two cooperating industrial robots, the supporting robot models a die on the back of the metal sheet by using the robot-based fused layer manufacturing process (FLM). This tool chain is software-defined and preserves the high geometrical form flexibility of Roboforming while flexibly generating support structures adapted to the final part's geometry. Test series serve to confirm the feasibility of the concept by investigating the process challenges of the adhesion to the sheet surface and the general stability as well as the influence on the geometric accuracy compared to the well-known forming strategies.

Using expectations to monitor robotic progress and recover from problems

Science.gov (United States)

Kurup, Unmesh; Lebiere, Christian; Stentz, Anthony; Hebert, Martial

2013-05-01

How does a robot know when something goes wrong? Our research answers this question by leveraging expectations - predictions about the immediate future - and using the mismatch between the expectations and the external world to monitor the robot's progress. We use the cognitive architecture ACT-R (Adaptive Control of Thought - Rational) to learn the associations between the current state of the robot and the world, the action to be performed in the world, and the future state of the world. These associations are used to generate expectations that are then matched by the architecture with the next state of the world. A significant mismatch between these expectations and the actual state of the world indicate a problem possibly resulting from unexpected consequences of the robot's actions, unforeseen changes in the environment or unanticipated actions of other agents. When a problem is detected, the recovery model can suggest a number of recovery options. If the situation is unknown, that is, the mismatch between expectations and the world is novel, the robot can use a recovery solution from a set of heuristic options. When a recovery option is successfully applied, the robot learns to associate that recovery option with the mismatch. When the same problem is encountered later, the robot can apply the learned recovery solution rather than using the heuristics or randomly exploring the space of recovery solutions. We present results from execution monitoring and recovery performed during an assessment conducted at the Combined Arms Collective Training Facility (CACTF) at Fort Indiantown Gap.

A Generic Approach to Self-localization and Mapping of Mobile Robots Without Using a Kinematic Model

DEFF Research Database (Denmark)

Kesper, Patrick; Berscheid, Lars; Wörgötter, Florentin

2015-01-01

and environment of a robot. Scan-matching is applied to compensate for noisy IMU measurements. This approach does not require any robot-specific characteristics, e.g. wheel encoders or kinematic models. In principle, this minimal sensory setup can be mounted on different robot systems without major modifications...... to the underlying algorithms. The sensory setup with the probabilistic algorithm is tested in real-world experiments on two different kinds of robots: a simple two-wheeled robot and the six-legged hexapod AMOSII. The obtained results indicate a successful implementation of the approach and confirm its generic...... nature. On both robots, the SLAM problem can be solved with reasonable accuracy....

Lightweight robotic mobility: template-based modeling for dynamics and controls using ADAMS/car and MATLAB

Science.gov (United States)

Adamczyk, Peter G.; Gorsich, David J.; Hudas, Greg R.; Overholt, James

2003-09-01

The U.S. Army is seeking to develop autonomous off-road mobile robots to perform tasks in the field such as supply delivery and reconnaissance in dangerous territory. A key problem to be solved with these robots is off-road mobility, to ensure that the robots can accomplish their tasks without loss or damage. We have developed a computer model of one such concept robot, the small-scale "T-1" omnidirectional vehicle (ODV), to study the effects of different control strategies on the robot's mobility in off-road settings. We built the dynamic model in ADAMS/Car and the control system in Matlab/Simulink. This paper presents the template-based method used to construct the ADAMS model of the T-1 ODV. It discusses the strengths and weaknesses of ADAMS/Car software in such an application, and describes the benefits and challenges of the approach as a whole. The paper also addresses effective linking of ADAMS/Car and Matlab for complete control system development. Finally, this paper includes a section describing the extension of the T-1 templates to other similar ODV concepts for rapid development.

Observation and imitation of actions performed by humans, androids, and robots: an EMG study

Science.gov (United States)

Hofree, Galit; Urgen, Burcu A.; Winkielman, Piotr; Saygin, Ayse P.

2015-01-01

Understanding others’ actions is essential for functioning in the physical and social world. In the past two decades research has shown that action perception involves the motor system, supporting theories that we understand others’ behavior via embodied motor simulation. Recently, empirical approach to action perception has been facilitated by using well-controlled artificial stimuli, such as robots. One broad question this approach can address is what aspects of similarity between the observer and the observed agent facilitate motor simulation. Since humans have evolved among other humans and animals, using artificial stimuli such as robots allows us to probe whether our social perceptual systems are specifically tuned to process other biological entities. In this study, we used humanoid robots with different degrees of human-likeness in appearance and motion along with electromyography (EMG) to measure muscle activity in participants’ arms while they either observed or imitated videos of three agents produce actions with their right arm. The agents were a Human (biological appearance and motion), a Robot (mechanical appearance and motion), and an Android (biological appearance and mechanical motion). Right arm muscle activity increased when participants imitated all agents. Increased muscle activation was found also in the stationary arm both during imitation and observation. Furthermore, muscle activity was sensitive to motion dynamics: activity was significantly stronger for imitation of the human than both mechanical agents. There was also a relationship between the dynamics of the muscle activity and motion dynamics in stimuli. Overall our data indicate that motor simulation is not limited to observation and imitation of agents with a biological appearance, but is also found for robots. However we also found sensitivity to human motion in the EMG responses. Combining data from multiple methods allows us to obtain a more complete picture of action

Observation and Imitation of Actions Performed by Humans, Androids and Robots: An EMG study

Directory of Open Access Journals (Sweden)

Galit eHofree

2015-06-01

Full Text Available Understanding others’ actions is essential for functioning in the physical and social world. In the past two decades research has shown that action perception involves the motor system, supporting theories that we understand others’ behavior via embodied motor simulation. Recently, action perception has been facilitated by using well-controlled artificial stimuli, such as robots. One key question this approach enables is what aspects of similarity between the observer and the observed agent facilitate motor simulation? Since humans have evolved among other humans and animals, using artificial stimuli such as robots allows us to probe whether our social perceptual systems are tuned to process other biological entities. In this study, we used humanoid robots with different degrees of humanlikeness in appearance and motion along with electromyography (EMG to measure muscle activity in participants’ arms while they either observed or imitated videos of three agents produce actions with their right arm. The agents were a Human (biological appearance and motion, a Robot (mechanical appearance and motion and an Android (biological appearance, mechanical motion. Right arm muscle activity increased when participants imitated all agents. Increased muscle activation was found also in the stationary arm both during imitation and observation. Furthermore, muscle activity was sensitive to motion dynamics: activity was significantly stronger for imitation of the human than both mechanical agents. There was also a relationship between the dynamics of the muscle activity and motion dynamics in stimuli. Overall our data indicate that motor simulation is not limited to observation and imitation of agents with a biological appearance, but is also found for robots. However we also found sensitivity to human motion in the EMG responses. Combining data from multiple methods allows us to obtain a more complete picture of action understanding and the underlying

Are You Talking to Me? Dialogue Systems Supporting Mixed Teams of Humans and Robots

Science.gov (United States)

Dowding, John; Clancey, William J.; Graham, Jeffrey

2006-01-01

This position paper describes an approach to building spoken dialogue systems for environments containing multiple human speakers and hearers, and multiple robotic speakers and hearers. We address the issue, for robotic hearers, of whether the speech they hear is intended for them, or more likely to be intended for some other hearer. We will describe data collected during a series of experiments involving teams of multiple human and robots (and other software participants), and some preliminary results for distinguishing robot-directed speech from human-directed speech. The domain of these experiments is Mars-analogue planetary exploration. These Mars-analogue field studies involve two subjects in simulated planetary space suits doing geological exploration with the help of 1-2 robots, supporting software agents, a habitat communicator and links to a remote science team. The two subjects are performing a task (geological exploration) which requires them to speak with each other while also speaking with their assistants. The technique used here is to use a probabilistic context-free grammar language model in the speech recognizer that is trained on prior robot-directed speech. Intuitively, the recognizer will give higher confidence to an utterance if it is similar to utterances that have been directed to the robot in the past.

CONTROL PREDICTIVO DE UN ROBOT TIPO SCARA PREDICTIVE CONTROL OF A SCARA ROBOT

Directory of Open Access Journals (Sweden)

Oscar Andrés Vivas Albán

2006-08-01

Full Text Available Este artículo presenta una aplicación eficiente de un control por modelo de referencia sobre un robot de tipo SCARA. El control estudiado es un control predictivo funcional, el que hace uso de un modelo dinámico simplificado del robot. Los ensayos simulados se realizan sobre un robot de cuatro grados de libertad, tipo SCARA. Con el fin de comparar diferentes estrategias de control, se diseña un controlador clásico tipo PID y dos controladores basados en el modelo de referencia. En este último caso el sistema se linealiza y se desacoplada por realimentación, lo que transforma el sistema a controlar en un simple par de integradores. Al sistema lineal y desacoplado resultante se le aplica el control por par calculado y el control predictivo funcional. Los tres controladores estudiados se simulan sobre el robot SCARA con valores numéricos reales. Las pruebas permiten valorar las respuestas de estos controladores en seguimiento de trayectoria, rechazo de perturbaciones y presencia de errores en el modelado con consignas complejas similares a las utilizadas en procesos de fabricación.This paper describes an efficient approach for model based control, applied on a SCARA robot. The studied control is the predictive functional control which uses a simplified dynamical model of the robot. The simulated tests are made on a SCARA type robot, with four DOF. To compare several control strategies, a classical PID control and two model based controllers are designed. In the last case, the model is first linearized and decoupled by feedback, transforming the system into a double set of integrators. Computed torque control and predictive functional control are applied to the linear and decoupled system. The three studied controllers are simulated on the SCARA robot with real numerical values. Tracking performance, disturbance rejection and model robot mismatch are enlightened, using complex machining tasks trajectories and error presence in the modelling

Modeling culture in intelligent virtual agents

NARCIS (Netherlands)

Mascarenhas, S.; Degens, N.; Paiva, A.; Prada, R.; Hofstede, G.J.; Beulens, A.J.M.; Aylett, R.

2016-01-01

This work addresses the challenge of creating virtual agents that are able to portray culturally appropriate behavior when interacting with other agents or humans. Because culture influences how people perceive their social reality it is important to have agent models that explicitly consider social

A Soft Body as a Reservoir: Case Studies in a Dynamic Model of Octopus-Inspired Soft Robotic Arm

Directory of Open Access Journals (Sweden)

Kohei eNakajima

2013-07-01

Full Text Available The behaviors of the animals or embodied agents are characterized by the dynamic coupling between the brain, the body, and the environment. This implies that control, which is conventionally thought to be handled by the brain or a controller, can partially be outsourced to the physical body and the interaction with the environment. This idea has been demonstrated in a number of recently constructed robots, in particular from the field of soft robotics. Soft robots are made of a soft material introducing high-dimensionality, nonlinearity, and elasticity, which often makes the robots difficult to control. Biological systems such as the octopus are mastering their complex bodies in highly sophisticated manners by capitalizing on their body dynamics. We will demonstrate that the structure of the octopus arm cannot only be exploited for generating behavior but also, in a sense, as a computational resource. By using a soft robotic arm inspired by the octopus we show in a number of experiments how control is partially incorporated into the physical arm’s dynamics and how the arm’s dynamics can be exploited to approximate nonlinear dynamical systems and embed nonlinear limit cycles. Future application scenarios as well as the implications of the results for the octopus biology are also discussed.

The Impact of Robot Tutor Nonverbal Social Behavior on Child Learning

Directory of Open Access Journals (Sweden)

James Kennedy

2017-04-01

Full Text Available Several studies have indicated that interacting with social robots in educational contexts may lead to a greater learning than interactions with computers or virtual agents. As such, an increasing amount of social human–robot interaction research is being conducted in the learning domain, particularly with children. However, it is unclear precisely what social behavior a robot should employ in such interactions. Inspiration can be taken from human–human studies; this often leads to an assumption that the more social behavior an agent utilizes, the better the learning outcome will be. We apply a nonverbal behavior metric to a series of studies in which children are taught how to identify prime numbers by a robot with various behavioral manipulations. We find a trend, which generally agrees with the pedagogy literature, but also that overt nonverbal behavior does not account for all learning differences. We discuss the impact of novelty, child expectations, and responses to social cues to further the understanding of the relationship between robot social behavior and learning. We suggest that the combination of nonverbal behavior and social cue congruency is necessary to facilitate learning.

Agent Based Modeling Applications for Geosciences

Science.gov (United States)

Stein, J. S.

2004-12-01

Agent-based modeling techniques have successfully been applied to systems in which complex behaviors or outcomes arise from varied interactions between individuals in the system. Each individual interacts with its environment, as well as with other individuals, by following a set of relatively simple rules. Traditionally this "bottom-up" modeling approach has been applied to problems in the fields of economics and sociology, but more recently has been introduced to various disciplines in the geosciences. This technique can help explain the origin of complex processes from a relatively simple set of rules, incorporate large and detailed datasets when they exist, and simulate the effects of extreme events on system-wide behavior. Some of the challenges associated with this modeling method include: significant computational requirements in order to keep track of thousands to millions of agents, methods and strategies of model validation are lacking, as is a formal methodology for evaluating model uncertainty. Challenges specific to the geosciences, include how to define agents that control water, contaminant fluxes, climate forcing and other physical processes and how to link these "geo-agents" into larger agent-based simulations that include social systems such as demographics economics and regulations. Effective management of limited natural resources (such as water, hydrocarbons, or land) requires an understanding of what factors influence the demand for these resources on a regional and temporal scale. Agent-based models can be used to simulate this demand across a variety of sectors under a range of conditions and determine effective and robust management policies and monitoring strategies. The recent focus on the role of biological processes in the geosciences is another example of an area that could benefit from agent-based applications. A typical approach to modeling the effect of biological processes in geologic media has been to represent these processes in

Computer assisted surgery with 3D robot models and visualisation of the telesurgical action.

Science.gov (United States)

Rovetta, A

2000-01-01

This paper deals with the support of virtual reality computer action in the procedures of surgical robotics. Computer support gives a direct representation of the surgical theatre. The modelization of the procedure in course and in development gives a psychological reaction towards safety and reliability. Robots similar to the ones used by the manufacturing industry can be used with little modification as very effective surgical tools. They have high precision, repeatability and are versatile in integrating with the medical instrumentation. Now integrated surgical rooms, with computer and robot-assisted intervention, are operating. The computer is the element for a decision taking aid, and the robot works as a very effective tool.

An Agent Model Integrating an Adaptive Model for Environmental Dynamics

NARCIS (Netherlands)

Treur, J.; Umair, M.

2011-01-01

The environments in which agents are used often may be described by dynamical models, e.g., in the form of a set of differential equations. In this paper, an agent model is proposed that can perform model-based reasoning about the environment, based on a numerical (dynamical system) model of the

Modelling and Control of Robotic Leg as Assistive Device

Science.gov (United States)

Jingye, Yee; Zain, Badrul Aisham bin Md

2017-10-01

The ageing population (people older than 60 years old) is expected to constitute 21.8% of global population by year 2050. When human ages, bodily function including locomotors will deteriorate. Besides, there are hundreds of thousands of victims who suffer from multiple health conditions worldwide that leads to gait impairment. A promising solution will be the lower limb powered-exoskeleton. This study is to be a start-up platform to design a lower limb powered-exoskeleton for a normal Malaysian male, by designing and simulating the dynamic model of a 2-link robotic leg to observe its behaviour under different input conditions with and without a PID controller. Simulink in MATLAB software is used as the dynamic modelling and simulation software for this study. It is observed that the 2-links robotic leg behaved differently under different input conditions, and perform the best when it is constrained and controlled by PID controller. Simulink model is formed as a foundation for the upcoming researches and can be modified and utilised by the future researchers.

Additive Manufacturing Cloud via Peer-Robot Collaboration

Directory of Open Access Journals (Sweden)

Yuan Yao

2016-05-01

Full Text Available When building a 3D printing cloud manufacturing platform, self-sensing and collaboration on manufacturing resources present challenging problems. This paper proposes a peer-robot collaboration framework to deal with these issues. Each robot combines heterogeneous additive manufacturing hardware and software, acting as an intelligent agent. Through collaboration with other robots, it forms a dynamic and scalable integration manufacturing system. The entire distributed system is managed by rules that employ an internal rule engine, which supports rule conversion and conflict resolution. Two additive manufacturing service scenarios are designed to analyse the efficiency and scalability of the framework. Experiments show that the presented method performs well in tasks requiring large-scale access to resources and collaboration.

Robots and lattice automata

CERN Document Server

Adamatzky, Andrew

2015-01-01

The book gives a comprehensive overview of the state-of-the-art research and engineering in theory and application of Lattice Automata in design and control of autonomous Robots. Automata and robots share the same notional meaning. Automata (originated from the latinization of the Greek word “αυτόματον”) as self-operating autonomous machines invented from ancient years can be easily considered the first steps of robotic-like efforts. Automata are mathematical models of Robots and also they are integral parts of robotic control systems. A Lattice Automaton is a regular array or a collective of finite state machines, or automata. The Automata update their states by the same rules depending on states of their immediate neighbours. In the context of this book, Lattice Automata are used in developing modular reconfigurable robotic systems, path planning and map exploration for robots, as robot controllers, synchronisation of robot collectives, robot vision, parallel robotic actuators. All chapters are...

Beyond speculative robot ethics: a vision assessment study on the future of the robotic caretaker.

Science.gov (United States)

van der Plas, Arjanna; Smits, Martijntje; Wehrmann, Caroline

2010-11-01

In this article we develop a dialogue model for robot technology experts and designated users to discuss visions on the future of robotics in long-term care. Our vision assessment study aims for more distinguished and more informed visions on future robots. Surprisingly, our experiment also led to some promising co-designed robot concepts in which jointly articulated moral guidelines are embedded. With our model, we think to have designed an interesting response on a recent call for a less speculative ethics of technology by encouraging discussions about the quality of positive and negative visions on the future of robotics.

Design-Oriented Enhanced Robotics Curriculum

Science.gov (United States)

Yilmaz, M.; Ozcelik, S.; Yilmazer, N.; Nekovei, R.

2013-01-01

This paper presents an innovative two-course, laboratory-based, and design-oriented robotics educational model. The robotics curriculum exposed senior-level undergraduate students to major robotics concepts, and enhanced the student learning experience in hybrid learning environments by incorporating the IEEE Region-5 annual robotics competition…

Modelling and testing proxemic behaviour for humanoid robots

NARCIS (Netherlands)

Torta, E.; Cuijpers, R.H.; Juola, J.F.; Pol, van der D.

2012-01-01

Humanoid robots that share the same space with humans need to be socially acceptable and effective as they interact with people. In this paper we focus our attention on the definition of a behavior-based robotic architecture that (1) allows the robot to navigate safely in a cluttered and dynamically

Numerical Modelling and Simulation of Dynamic Parameters for Vibration Driven Mobile Robot: Preliminary Study

Science.gov (United States)

Baharudin, M. E.; Nor, A. M.; Saad, A. R. M.; Yusof, A. M.

2018-03-01

The motion of vibration-driven robots is based on an internal oscillating mass which can move without legs or wheels. The oscillation of the unbalanced mass by a motor is translated into vibration which in turn produces vertical and horizontal forces. Both vertical and horizontal oscillations are of the same frequency but the phases are shifted. The vertical forces will deflect the bristles which cause the robot to move forward. In this paper, the horizontal motion direction caused by the vertically vibrated bristle is numerically simulated by tuning the frequency of their oscillatory actuation. As a preliminary work, basic equations for a simple off-centered vibration location on the robot platform and simulation model for vibration excitement are introduced. It involves both static and dynamic vibration analysis of robots and analysis of different type of parameters. In addition, the orientation of the bristles and oscillators are also analysed. Results from the numerical integration seem to be in good agreement with those achieved from the literature. The presented numerical integration modeling can be used for designing the bristles and controlling the speed and direction of the robot.

Kinematic Modelling and Simulation of a 2-R Robot Using SolidWorks and Verification by MATLAB/Simulink

Directory of Open Access Journals (Sweden)

Mahmoud Gouasmi

2012-12-01

Full Text Available The simulation of robot systems is becoming very popular, especially with the lowering of the cost of computers, and it can be used for layout evaluation, feasibility studies, presentations with animation and off-line programming. The trajectory planning of redundant manipulators is a very active area since many tasks require special characteristics to be satisfied. The importance of redundant manipulators has increased over the last two decades because of the possibility of avoiding singularities as well as obstacles within the course of motion. The angle that the last link of a 2 DOF manipulator makes with the x-axis is required in order to find the solution for the inverse kinematics problem. This angle could be optimized with respect to a given specified key factor (time, velocity, torques while the end-effector performs a chosen trajectory (i.e., avoiding an obstacle in the task space. Modeling and simulation of robots could be achieved using either of the following models: the geometrical model (positions, postures, the kinematic model and the dynamic model. To do so, the modelization of a 2-R robot type is implemented. Our main tasks are comparing two robot postures with the same trajectory (path and for the same length of time, and establishing a computing code to obtain the kinematic and dynamic parameters. SolidWorks and MATLAB/Simulink softwares are used to check the theory and the robot motion simulation. This could be easily generalized to a 3-R robot and possibly therefore to any serial robot (Scara, Puma, etc.. The verification of the obtained results by both softwares allows us to qualitatively evaluate and underline the validityof the chosen model and obtain the right conclusions. The results of the simulations are discussed and an agreement between the two softwares is certainly obtained.

Controlling the autonomy of a reconnaissance robot

Science.gov (United States)

Dalgalarrondo, Andre; Dufourd, Delphine; Filliat, David

2004-09-01

In this paper, we present our research on the control of a mobile robot for indoor reconnaissance missions. Based on previous work concerning our robot control architecture HARPIC, we have developed a man machine interface and software components that allow a human operator to control a robot at different levels of autonomy. This work aims at studying how a robot could be helpful in indoor reconnaissance and surveillance missions in hostile environment. In such missions, since a soldier faces many threats and must protect himself while looking around and holding his weapon, he cannot devote his attention to the teleoperation of the robot. Moreover, robots are not yet able to conduct complex missions in a fully autonomous mode. Thus, in a pragmatic way, we have built a software that allows dynamic swapping between control modes (manual, safeguarded and behavior-based) while automatically performing map building and localization of the robot. It also includes surveillance functions like movement detection and is designed for multirobot extensions. We first describe the design of our agent-based robot control architecture and discuss the various ways to control and interact with a robot. The main modules and functionalities implementing those ideas in our architecture are detailed. More precisely, we show how we combine manual controls, obstacle avoidance, wall and corridor following, way point and planned travelling. Some experiments on a Pioneer robot equipped with various sensors are presented. Finally, we suggest some promising directions for the development of robots and user interfaces for hostile environment and discuss our planned future improvements.

Distance-Based Behaviors for Low-Complexity Control in Multiagent Robotics

Science.gov (United States)

Pierpaoli, Pietro

Several biological examples show that living organisms cooperate to collectively accomplish tasks impossible for single individuals. More importantly, this coordination is often achieved with a very limited set of information. Inspired by these observations, research on autonomous systems has focused on the development of distributed control techniques for control and guidance of groups of autonomous mobile agents, or robots. From an engineering perspective, when coordination and cooperation is sought in large ensembles of robotic vehicles, a reduction in hardware and algorithms' complexity becomes mandatory from the very early stages of the project design. The research for solutions capable of lowering power consumption, cost and increasing reliability are thus worth investigating. In this work, we studied low-complexity techniques to achieve cohesion and control on swarms of autonomous robots. Starting from an inspiring example with two-agents, we introduced effects of neighbors' relative positions on control of an autonomous agent. The extension of this intuition addressed the control of large ensembles of autonomous vehicles, and was applied in the form of a herding-like technique. To this end, a low-complexity distance-based aggregation protocol was defined. We first showed that our protocol produced a cohesion aggregation among the agent while avoiding inter-agent collisions. Then, a feedback leader-follower architecture was introduced for the control of the swarm. We also described how proximity measures and probability of collisions with neighbors can also be used as source of information in highly populated environments.

Modeling and evaluation of hand-eye coordination of surgical robotic system on task performance.

Science.gov (United States)

Gao, Yuanqian; Wang, Shuxin; Li, Jianmin; Li, Aimin; Liu, Hongbin; Xing, Yuan

2017-12-01

Robotic-assisted minimally invasive surgery changes the direct hand and eye coordination in traditional surgery to indirect instrument and camera coordination, which affects the ergonomics, operation performance, and safety. A camera, two instruments, and a target, as the descriptors, are used to construct the workspace correspondence and geometrical relationships in a surgical operation. A parametric model with a set of parameters is proposed to describe the hand-eye coordination of the surgical robot. From the results, optimal values and acceptable ranges of these parameters are identified from two tasks. A 90° viewing angle had the longest completion time; 60° instrument elevation angle and 0° deflection angle had better performance; there is no significant difference among manipulation angles and observing distances on task performance. This hand-eye coordination model provides evidence for robotic design, surgeon training, and robotic initialization to achieve dexterous and safe manipulation in surgery. Copyright © 2017 John Wiley & Sons, Ltd.

Persistent agents in Axelrod's social dynamics model

Science.gov (United States)

Reia, Sandro M.; Neves, Ubiraci P. C.

2016-01-01

Axelrod's model of social dynamics has been studied under the effect of external media. Here we study the formation of cultural domains in the model by introducing persistent agents. These are agents whose cultural traits are not allowed to change but may be spread through local neighborhood. In the absence of persistent agents, the system is known to present a transition from a monocultural to a multicultural regime at some critical Q (number of traits). Our results reveal a dependence of critical Q on the occupation probability p of persistent agents and we obtain the phase diagram of the model in the (p,Q) -plane. The critical locus is explained by the competition of two opposite forces named here barrier and bonding effects. Such forces are verified to be caused by non-persistent agents which adhere (adherent agents) to the set of traits of persistent ones. The adherence (concentration of adherent agents) as a function of p is found to decay for constant Q. Furthermore, adherence as a function of Q is found to decay as a power law with constant p.

A Multidisciplinary Artificial Intelligence Model of an Affective Robot

Directory of Open Access Journals (Sweden)

Hooman Aghaebrahimi Samani

2012-03-01

Full Text Available A multidisciplinary approach to a novel artificial intelligence system for an affective robot is presented in this paper. The general objective of the system is to develop a robotic system which strives to achieve a high level of emotional bond between humans and robot by exploring human love. Such a relationship is a contingent process of attraction, affection and attachment from humans towards robots, and the belief of the vice versa from robots to humans. The advanced artificial intelligence of the system includes three modules, namely Probabilistic Love Assembly (PLA, based on the psychology of love, Artificial Endocrine System (AES, based on the physiology of love, and Affective State Transition (AST, based on emotions. The PLA module employs a Bayesian network to incorporate psychological parameters of affection in the robot. The AES module employs artificial emotional and biological hormones via a Dynamic Bayesian Network (DBN. The AST module uses a novel transition method for handling affective states of the robot. These three modules work together to manage emotional behaviours of the robot.

An Emotional Agent Model Based on Granular Computing

Directory of Open Access Journals (Sweden)

Jun Hu

2012-01-01

Full Text Available Affective computing has a very important significance for fulfilling intelligent information processing and harmonious communication between human being and computers. A new model for emotional agent is proposed in this paper to make agent have the ability of handling emotions, based on the granular computing theory and the traditional BDI agent model. Firstly, a new emotion knowledge base based on granular computing for emotion expression is presented in the model. Secondly, a new emotional reasoning algorithm based on granular computing is proposed. Thirdly, a new emotional agent model based on granular computing is presented. Finally, based on the model, an emotional agent for patient assistant in hospital is realized, experiment results show that it is efficient to handle simple emotions.

Novel Adaptive Forward Neural MIMO NARX Model for the Identification of Industrial 3-DOF Robot Arm Kinematics

Directory of Open Access Journals (Sweden)

Ho Pham Huy Anh

2012-10-01

Full Text Available In this paper, a novel forward adaptive neural MIMO NARX model is used for modelling and identifying the forward kinematics of an industrial 3-DOF robot arm system. The nonlinear features of the forward kinematics of the industrial robot arm drive are thoroughly modelled based on the forward adaptive neural NARX model-based identification process using experimental input-output training data. This paper proposes a novel use of a back propagation (BP algorithm to generate the forward neural MIMO NARX (FNMN model for the forward kinematics of the industrial 3-DOF robot arm. The results show that the proposed adaptive neural NARX model trained by a Back Propagation learning algorithm yields outstanding performance and perfect accuracy.

Application of model based control to robotic manipulators

Science.gov (United States)

Petrosky, Lyman J.; Oppenheim, Irving J.

1988-01-01

A robot that can duplicate humam motion capabilities in such activities as balancing, reaching, lifting, and moving has been built and tested. These capabilities are achieved through the use of real time Model-Based Control (MBC) techniques which have recently been demonstrated. MBC accounts for all manipulator inertial forces and provides stable manipulator motion control even at high speeds. To effectively demonstrate the unique capabilities of MBC, an experimental robotic manipulator was constructed, which stands upright, balancing on a two wheel base. The mathematical modeling of dynamics inherent in MBC permit the control system to perform functions that are impossible with conventional non-model based methods. These capabilities include: (1) Stable control at all speeds of operation; (2) Operations requiring dynamic stability such as balancing; (3) Detection and monitoring of applied forces without the use of load sensors; (4) Manipulator safing via detection of abnormal loads. The full potential of MBC has yet to be realized. The experiments performed for this research are only an indication of the potential applications. MBC has no inherent stability limitations and its range of applicability is limited only by the attainable sampling rate, modeling accuracy, and sensor resolution. Manipulators could be designed to operate at the highest speed mechanically attainable without being limited by control inadequacies. Manipulators capable of operating many times faster than current machines would certainly increase productivity for many tasks.

Proxemics models for human-aware navigation in robotics: Grounding interaction and personal space models in experimental data from psychology

OpenAIRE

Barnaud , Marie-Lou; Morgado , Nicolas; Palluel-Germain , Richard; Diard , Julien; Spalanzani , Anne

2014-01-01

International audience; In order to navigate in a social environment, a robot must be aware of social spaces, which include proximity and interaction-based constraints. Previous models of interaction and personal spaces have been inspired by studies in social psychology but not systematically grounded and validated with respect to experimental data. We propose to implement personal and interaction space models in order to replicate a classical psychology experiment. Our robotic simulations ca...

An Agent-Based Monetary Production Simulation Model

DEFF Research Database (Denmark)

Bruun, Charlotte

2006-01-01

An Agent-Based Simulation Model Programmed in Objective Borland Pascal. Program and source code is downloadable......An Agent-Based Simulation Model Programmed in Objective Borland Pascal. Program and source code is downloadable...

Approaches to probabilistic model learning for mobile manipulation robots

CERN Document Server

Sturm, Jürgen

2013-01-01

Mobile manipulation robots are envisioned to provide many useful services both in domestic environments as well as in the industrial context. Examples include domestic service robots that implement large parts of the housework, and versatile industrial assistants that provide automation, transportation, inspection, and monitoring services. The challenge in these applications is that the robots have to function under changing, real-world conditions, be able to deal with considerable amounts of noise and uncertainty, and operate without the supervision of an expert. This book presents novel learning techniques that enable mobile manipulation robots, i.e., mobile platforms with one or more robotic manipulators, to autonomously adapt to new or changing situations. The approaches presented in this book cover the following topics: (1) learning the robot's kinematic structure and properties using actuation and visual feedback, (2) learning about articulated objects in the environment in which the robot is operating,...

A Multi-Agent Framework for Coordination of Intelligent Assistive Technologies

DEFF Research Database (Denmark)

Valente, Pedro Ricardo da Nova; Hossain, S.; Groenbaek, B.

2010-01-01

Intelligent care for the future is the IntelliCare project's main priority. This paper describes the design of a generic multi-agent framework for coordination of intelligent assistive technologies. The paper overviews technologies and software systems suitable for context awareness...... and housekeeping tasks, especially for performing a multi-robot cleaning-task activity. It also describes conducted work in the design of a multi-agent platform for coordination of intelligent assistive technologies. Instead of using traditional robot odometry estimation methods, we have tested an independent...

A principal-agent Model of corruption

NARCIS (Netherlands)

Groenendijk, Nico

1997-01-01

One of the new avenues in the study of political corruption is that of neo-institutional economics, of which the principal-agent theory is a part. In this article a principal-agent model of corruption is presented, in which there are two principals (one of which is corrupting), and one agent (who is

Beyond Speculative Robot Ethics

NARCIS (Netherlands)

Smits, M.; Van der Plas, A.

2010-01-01

In this article we develop a dialogue model for robot technology experts and designated users to discuss visions on the future of robotics in long-term care. Our vision assessment study aims for more distinguished and more informed visions on future robots. Surprisingly, our experiment also lead to

Evaluating Water Demand Using Agent-Based Modeling

Science.gov (United States)

Lowry, T. S.

2004-12-01

The supply and demand of water resources are functions of complex, inter-related systems including hydrology, climate, demographics, economics, and policy. To assess the safety and sustainability of water resources, planners often rely on complex numerical models that relate some or all of these systems using mathematical abstractions. The accuracy of these models relies on how well the abstractions capture the true nature of the systems interactions. Typically, these abstractions are based on analyses of observations and/or experiments that account only for the statistical mean behavior of each system. This limits the approach in two important ways: 1) It cannot capture cross-system disruptive events, such as major drought, significant policy change, or terrorist attack, and 2) it cannot resolve sub-system level responses. To overcome these limitations, we are developing an agent-based water resources model that includes the systems of hydrology, climate, demographics, economics, and policy, to examine water demand during normal and extraordinary conditions. Agent-based modeling (ABM) develops functional relationships between systems by modeling the interaction between individuals (agents), who behave according to a probabilistic set of rules. ABM is a "bottom-up" modeling approach in that it defines macro-system behavior by modeling the micro-behavior of individual agents. While each agent's behavior is often simple and predictable, the aggregate behavior of all agents in each system can be complex, unpredictable, and different than behaviors observed in mean-behavior models. Furthermore, the ABM approach creates a virtual laboratory where the effects of policy changes and/or extraordinary events can be simulated. Our model, which is based on the demographics and hydrology of the Middle Rio Grande Basin in the state of New Mexico, includes agent groups of residential, agricultural, and industrial users. Each agent within each group determines its water usage

Empirical agent-based modelling challenges and solutions

CERN Document Server

Barreteau, Olivier

2014-01-01

This instructional book showcases techniques to parameterise human agents in empirical agent-based models (ABM). In doing so, it provides a timely overview of key ABM methodologies and the most innovative approaches through a variety of empirical applications.  It features cutting-edge research from leading academics and practitioners, and will provide a guide for characterising and parameterising human agents in empirical ABM.  In order to facilitate learning, this text shares the valuable experiences of other modellers in particular modelling situations. Very little has been published in the area of empirical ABM, and this contributed volume will appeal to graduate-level students and researchers studying simulation modeling in economics, sociology, ecology, and trans-disciplinary studies, such as topics related to sustainability. In a similar vein to the instruction found in a cookbook, this text provides the empirical modeller with a set of 'recipes'  ready to be implemented. Agent-based modeling (AB...

14th International Conference on Practical Applications of Agents and Multi-Agent Systems : Special Sessions

CERN Document Server

Escalona, María; Corchuelo, Rafael; Mathieu, Philippe; Vale, Zita; Campbell, Andrew; Rossi, Silvia; Adam, Emmanuel; Jiménez-López, María; Navarro, Elena; Moreno, María

2016-01-01

PAAMS, the International Conference on Practical Applications of Agents and Multi-Agent Systems is an evolution of the International Workshop on Practical Applications of Agents and Multi-Agent Systems. PAAMS is an international yearly tribune to present, to discuss, and to disseminate the latest developments and the most important outcomes related to real-world applications. It provides a unique opportunity to bring multi-disciplinary experts, academics and practitioners together to exchange their experience in the development of Agents and Multi-Agent Systems. This volume presents the papers that have been accepted for the 2016 in the special sessions: Agents Behaviours and Artificial Markets (ABAM); Advances on Demand Response and Renewable Energy Sources in Agent Based Smart Grids (ADRESS); Agents and Mobile Devices (AM); Agent Methodologies for Intelligent Robotics Applications (AMIRA); Learning, Agents and Formal Languages (LAFLang); Multi-Agent Systems and Ambient Intelligence (MASMAI); Web Mining and ...

Analytical basis for evaluating the effect of unplanned interventions on the effectiveness of a human-robot system

International Nuclear Information System (INIS)

Shah, Julie A.; Saleh, Joseph H.; Hoffman, Jeffrey A.

2008-01-01

Increasing prevalence of human-robot systems in a variety of applications raises the question of how to design these systems to best leverage the capabilities of humans and robots. In this paper, we address the relationships between reliability, productivity, and risk to humans from human-robot systems operating in a hostile environment. Objectives for maximizing the effectiveness of a human-robot system are presented, which capture these coupled relationships, and reliability parameters are proposed to characterize unplanned interventions between a human and robot. The reliability metrics defined here take on an expanded meaning in which the underlying concept of failure in traditional reliability analysis is replaced by the notion of intervention. In the context of human-robotic systems, an intervention is not only driven by component failures, but includes many other factors that can make a robotic agent to request or a human agent to provide intervention, as we argue in this paper. The effect of unplanned interventions on the effectiveness of human-robot systems is then investigated analytically using traditional reliability analysis. Finally, we discuss the implications of these analytical trends on the design and evaluation of human-robot systems

A New Architecture for Making Moral Agents Based on C4.5 Decision Tree Algorithm

OpenAIRE

Meisam Azad-Manjiri

2014-01-01

Regarding to the influence of robots in the various fields of life, the issue of trusting to them is important, especially when a robot deals with people directly. One of the possible ways to get this confidence is adding a moral dimension to the robots. Therefore, we present a new architecture in order to build moral agents that learn from demonstrations. This agent is based on Beauchamp and Childress’s principles of biomedical ethics (a type of deontological theory) and uses decision tree a...

Towards Behavior Control for Evolutionary Robot Based on RL with ENN

Directory of Open Access Journals (Sweden)

Jingan Yang

2012-03-01

Full Text Available This paper proposes a behavior-switching control strategy of anevolutionary robotics based on Artificial NeuralNetwork (ANN and Genetic Algorithms (GA. This method is able not only to construct thereinforcement learning models for autonomous robots and evolutionary robot modules thatcontrol behaviors and reinforcement learning environments, and but also to perform thebehavior-switching control and obstacle avoidance of an evolutionary robotics (ER intime-varying environments with static and moving obstacles by combining ANN and GA.The experimental results on thebasic behaviors and behavior-switching control have demonstrated that ourmethod can perform the decision-making strategy and parameters set opimization ofFNN and GA by learning and can escape successfully from the trap of a localminima and avoid \\emph{"motion deadlock" status} of humanoid soccer robotics agents,and reduce the oscillation of the planned trajectory betweenthe multiple obstacles by crossover and mutation. Some results of the proposed algorithmhave been successfully applied to our simulation humanoid robotics soccer team CIT3Dwhich won \\emph{the 1st prize} of RoboCup Championship and ChinaOpen2010 (July 2010 and \\emph{the $2^{nd}$ place}of the official RoboCup World Championship on 5-11 July, 2011 in Istanbul, Turkey.As compared with the conventional behavior network and the adaptive behavior method,the genetic encoding complexity of our algorithm is simplified, and the networkperformance and the {\\em convergence rate $\\rho$} have been greatlyimproved.

A conceptual data model and modelling language for fields and agents

Science.gov (United States)

de Bakker, Merijn; de Jong, Kor; Schmitz, Oliver; Karssenberg, Derek

2016-04-01

Modelling is essential in order to understand environmental systems. Environmental systems are heterogeneous because they consist of fields and agents. Fields have a value defined everywhere at all times, for example surface elevation and temperature. Agents are bounded in space and time and have a value only within their bounds, for example biomass of a tree crown or the speed of a car. Many phenomena have properties of both fields and agents. Although many systems contain both fields and agents and integration of these concepts would be required for modelling, existing modelling frameworks concentrate on either agent-based or field-based modelling and are often low-level programming frameworks. A concept is lacking that integrates fields and agents in a way that is easy to use for modelers who are not software engineers. To address this issue, we develop a conceptual data model that represents fields and agents uniformly. We then show how the data model can be used in a high-level modelling language. The data model represents fields and agents in space-time. Also relations and networks can be represented using the same concepts. Using the conceptual data model we can represent static and mobile agents that may have spatial and temporal variation within their extent. The concepts we use are phenomenon, property set, item, property, domain and value. The phenomenon is the thing that is modelled, which can be any real world thing, for example trees. A phenomenon usually consists of several items, e.g. single trees. The domain is the spatiotemporal location and/or extent for which the items in the phenomenon are defined. Multiple different domains can coexist for a given phenomenon. For example a domain describing the extent of the trees and a domain describing the stem locations. The same goes for the property, which is an attribute of the thing that is being modeled. A property has a value, which is possibly discretized, for example the biomass over the tree crown

Smart Agents and Sentiment in the Heterogeneous Agent Model

Czech Academy of Sciences Publication Activity Database

Vácha, Lukáš; Baruník, Jozef; Vošvrda, Miloslav

-, č. 81 (2010), s. 39-40 ISSN 0926-4981 R&D Projects: GA ČR(CZ) GA402/09/0965; GA ČR GP402/08/P207 Grant - others:GAUK(CZ) GAUK 46108 Institutional research plan: CEZ:AV0Z10750506 Keywords : Smart traders * price movements * smart traders concept Subject RIV: AH - Economics http://library.utia.cas.cz/separaty/2010/E/vacha- smart agent s and sentiment in the heterogeneous agent model.pdf

History-Based Response Threshold Model for Division of Labor in Multi-Agent Systems

Science.gov (United States)

Lee, Wonki; Kim, DaeEun

2017-01-01

Dynamic task allocation is a necessity in a group of robots. Each member should decide its own task such that it is most commensurate with its current state in the overall system. In this work, the response threshold model is applied to a dynamic foraging task. Each robot employs a task switching function based on the local task demand obtained from the surrounding environment, and no communication occurs between the robots. Each individual member has a constant-sized task demand history that reflects the global demand. In addition, it has response threshold values for all of the tasks and manages the task switching process depending on the stimuli of the task demands. The robot then determines the task to be executed to regulate the overall division of labor. This task selection induces a specialized tendency for performing a specific task and regulates the division of labor. In particular, maintaining a history of the task demands is very effective for the dynamic foraging task. Various experiments are performed using a simulation with multiple robots, and the results show that the proposed algorithm is more effective as compared to the conventional model. PMID:28555031

Analysis and Development of Walking Algorithm Kinematic Model for 5-Degree of Freedom Bipedal Robot

Directory of Open Access Journals (Sweden)

Gerald Wahyudi Setiono

2012-12-01

Full Text Available A design of walking diagram and the calculation of a bipedal robot have been developed. The bipedal robot was designed and constructed with several kinds of servo bracket for the legs, two feet and a hip. Each of the bipedal robot leg was 5-degrees of freedom, three pitches (hip joint, knee joint and ankle joint and two rolls (hip joint and ankle joint. The walking algorithm of this bipedal robot was based on the triangle formulation of cosine law to get the angle value at each joint. The hip height, height of the swinging leg and the step distance are derived based on linear equation. This paper discussed the kinematic model analysis and the development of the walking diagram of the bipedal robot. Kinematics equations were derived, the joint angles were simulated and coded into Arduino board to be executed to the robot.

Design of a robotized workstation making use of the integration of CAD models and Robotic Simulation software as way of pairing and comparing real and virtual environments

Directory of Open Access Journals (Sweden)

Velíšek Karol

2017-01-01

Full Text Available Over the last years, there has been an increasing tendency and pressure on the faster implementation robotic devices and systems in manufacturing. Such transition involves several disciplines starting with the prototyping of CAD models itself. The paper addresses the creation of CAD models and is mainly aimed at their integration in a given simulation environment according to the conception and guidelines of Industry 4.0, where the part itself becomes the entity carrying most of the needed information at any time of a production process. The creation of such CAD models is key for the further and better customization of simulations. In other to better exemplify all this, the paper describes the whole process of “virtual to real life implementation” of a given robotized workplace needed to be developed at the Institute. The design of such robotized workplace included the use of an ABB IRB 120 robot and several other devices which were all designed, simulated and analyzed in a virtual environment before the final development and implementation. This paper helped demonstrating the importance of having exactly the same model (real and virtual with respect to the success of the offline simulations.

Modelling of gecko foot for future robot application

Science.gov (United States)

Kamaruddin, A.; Ong, N. R.; Aziz, M. H. A.; Alcain, J. B.; Haimi, W. M. W. N.; Sauli, Z.

2017-09-01

Every gecko has an approximately million microscale hairs called setae which made it easy for them to cling from different surfaces at any orientation with the aid of Van der Waals force as the primary mechanism used to adhere to any contact surfaces. In this paper, a strain simulation using Comsol Multiphysic Software was conducted on a 3D MEMS model of an actuated gecko foot with the aim of achieving optimal sticking with various polymetric materials for future robots application. Based on the stress and strain analyses done on the seven different polymers, it was found that polysilicon had the best result which was nearest to 0%, indicating the strongest elasticity among the others. PDMS on the hand, failed in the simulation due to its bulk-like nature. Thus, PDMS was not suitable to be used for further study on gecko foot robot.

Effect of cognitive biases on human-robot interaction: a case study of robot's misattribution