Visualizing the influence of the process parameters on the keyhole dimensions in plasma arc welding

International Nuclear Information System (INIS)

Liu, Z M; Wu, C S; Chen, M A

2012-01-01

The keyhole status and its dimensions are critical information determining both the process quality and weld quality in plasma arc welding (PAW). It is of great significance to measure the keyhole shape and size and to correlate them with the main process parameters. In this study, a low-cost vision system is developed to visualize the keyhole at the backside of the test-pieces in PAW. Three stages of keyhole evolution, i.e. initial blind stage (non-penetrated keyhole), unstable stage with momentarily disappeared keyhole and quasi-steady open keyhole stage (fully-penetrated keyhole), are measured in real-time during the PAW tests on stainless steel test-pieces of thickness 8 mm. Based on the captured images of keyhole under different welding conditions, the correlations of the main welding process parameters (welding current, welding speed, plasma gas flow rate) with the keyhole length, width and area are visualized through vision measurement. It lays a solid foundation for implementing keyhole stability control and process optimization in keyhole PAW. (paper)

Vapor plume oscillation mechanisms in transient keyhole during tandem dual beam fiber laser welding

Science.gov (United States)

Chen, Xin; Zhang, Xiaosi; Pang, Shengyong; Hu, Renzhi; Xiao, Jianzhong

2018-01-01

Vapor plume oscillations are common physical phenomena that have an important influence on the welding process in dual beam laser welding. However, until now, the oscillation mechanisms of vapor plumes remain unclear. This is primarily because mesoscale vapor plume dynamics inside a millimeter-scale, invisible, and time-dependent keyhole are difficult to quantitatively observe. In this paper, based on a developed three-dimensional (3D) comprehensive model, the vapor plume evolutions in a dynamical keyhole are directly simulated in tandem dual beam, short-wavelength laser welding. Combined with the vapor plume behaviors outside the keyhole observed by high-speed imaging, the vapor plume oscillations in dynamical keyholes at different inter-beam distances are the first, to our knowledge, to be quantitatively analyzed. It is found that vapor plume oscillations outside the keyhole mainly result from vapor plume instabilities inside the keyhole. The ejection velocity at the keyhole opening and dynamical behaviors outside the keyhole of a vapor plume both violently oscillate with the same order of magnitude of high frequency (several kHz). Furthermore, the ejection speed at the keyhole opening and ejection area outside the keyhole both decrease as the beam distance increases, while the degree of vapor plume instability first decreases and then increases with increasing beam distance from 0.6 to 1.0 mm. Moreover, the oscillation mechanisms of a vapor plume inside the dynamical keyhole irradiated by dual laser beams are investigated by thoroughly analyzing the vapor plume occurrence and flow process. The vapor plume oscillations in the dynamical keyhole are found to mainly result from violent local evaporations and severe keyhole geometry variations. In short, the quantitative method and these findings can serve as a reference for further understanding of the physical mechanisms in dual beam laser welding and of processing optimizations in industrial applications.

Multiple reflections and Fresnel absorption in an actual 3D keyhole during deep penetration laser welding

Energy Technology Data Exchange (ETDEWEB)

Jin Xiangzhong [Laser Institute of Hunan University, Changsha, Hunan, 410082 (China); Berger, Peter [Institut fuer Strahlwerkzeuge (IFSW), University of Stuttgart, Pfaffenwaldring 43, 70569 Stuttgart (Germany); Graf, Thomas [Institut fuer Strahlwerkzeuge (IFSW), University of Stuttgart, Pfaffenwaldring 43, 70569 Stuttgart (Germany)

2006-11-07

In laser welding experiments of glass, keyhole shapes are observed by two high-speed cameras from two perpendicular directions. From the obtained keyhole pictures, it can be seen that in medium- and low-speed laser penetration welding, the main distortion of the keyhole is not the section metamorphosis from rotational symmetry, but the bending of its centre line. Based on such a keyhole photograph, the keyhole profiles and its centre line are determined by the method of polynomial fitting. Then, under the assumption of a circular cross section at each depth of the keyhole, the behaviour of the laser beam in the keyhole is analysed by tracing a ray of light using geometrical optics theory; the Fresnel absorption and multiple reflections in the keyhole are systematically studied, and the laser intensities absorbed on the keyhole walls are calculated. The absorbed laser intensity is not distributed uniformly on the keyhole wall. The keyhole wall absorbs laser intensity mainly on the half-part of the keyhole wall near the front wall. Because of the high absorptivity of the glass, Fresnel absorption from the first incidence of a laser beam plays a dominant role in the final laser intensity distribution on the keyhole wall, multiple reflections have some minor effects on the intensity distribution on the bottom part of the keyhole.

Removal of vestibular schwannoma and facial nerve preservation using small suboccipital retrosigmoid craniotomy

Institute of Scientific and Technical Information of China (English)

CHEN Ling; CHEN Li-hua; LING Feng; LIU Yun-sheng; Madjid Samii; Amir Samii

2010-01-01

Background Vestibular schwannoma, the commonest form of intracranial schwannoma, arises from the Schwann cells investing the vestibular nerve. At present, the surgery for vestibular schwannoma remains one of the most complicated operations demanding for surgical skills in neurosurgery. And the trend of minimal invasion should also be the major influence on the management of patients with vestibular schwannomas. We summarized the microsurgical removal experience in a recent series of vestibular schwannomas and presented the operative technique and cranial nerve preservation in order to improve the rates of total tumor removal and facial nerve preservation.Methods A retrospective analysis was performed in 145 patients over a 7-year period who suffered from vestibular schwannomas that had been microsurgicaily removed by suboccipital retrosigmoid transmeatus approach with small craniotomy. CT thinner scans revealed the tumor size in the internal auditory meatus and the relationship of the posterior wall of the internal acoustic meatus to the bone labyrinths preoperatively. Brain stem evoked potential was monitored intraoperatively. The posterior wall of the internal acoustic meatus was designedly drilled off. Patient records and operative reports, including data from the electrophysiological monitoring, follow-up audiometric examinations, and neuroradiological findings were analyzed.Results Total tumor resection was achieved in 140 cases (96.6%) and subtotal resection in 5 cases. The anatomical integrity of the facial nerve was preserved in 91.0% (132/145) of the cases. Intracranial end-to-end anastomosis of the facial nerve was performed in 7 cases. Functional preservation of the facial nerve was achieved in 115 patients (Grade Ⅰ and Grade Ⅱ, 79.3%). No patient died in this series. Preservation of nerves and vessels were as important as tumor removal dudng the operation. CT thinner scan could show the relationship between the posterior wall of the internal

Numerical modeling of keyhole dynamics in laser welding

Science.gov (United States)

Zhang, Wen-Hai; Zhou, Jun; Tsai, Hai-Lung

2003-03-01

Mathematical models and the associated numerical techniques have been developed to study the following cases: (1) the formation and collapse of a keyhole, (2) the formation of porosity and its control strategies, (3) laser welding with filler metals, and (4) the escape of zinc vapor in laser welding of galvanized steel. The simulation results show that the formation of porosity in the weld is caused by two competing mechanisms: one is the solidification rate of the molten metal and the other is the speed that molten metal backfills the keyhole after laser energy is terminated. The models have demonstrated that porosity can be reduced or eliminated by adding filler metals, controlling laser tailing power, or applying an electromagnetic force during keyhole collapse process. It is found that a uniform composition of weld pool is difficult to achieve by filler metals due to very rapid solidification of the weld pool in laser welding, as compared to that in gas metal arc welding.

WE-G-18C-08: Real Time Tumor Imaging Using a Novel Dynamic Keyhole MRI Reconstruction Technique

International Nuclear Information System (INIS)

Lee, D; Pollock, S; Whelan, B; Keall, P; Greer, P; Kim, T

2014-01-01

Purpose: To test the hypothesis that the novel Dynamic Keyhole MRI reconstruction technique can accelerate image acquisition whilst maintaining high image quality for lung cancer patients. Methods: 18 MRI datasets from 5 lung cancer patients were acquired using a 3T MRI scanner. These datasets were retrospectively reconstructed using (A) The novel Dynamic Keyhole technique, (B) The conventional keyhole technique and (C) the conventional zero filling technique. The dynamic keyhole technique in MRI refers to techniques in which previously acquired k-space data is used to supplement under sampled data obtained in real time. The novel Dynamic Keyhole technique utilizes a previously acquired a library of kspace datasets in conjunction with central k-space datasets acquired in realtime. A simultaneously acquired respiratory signal is utilized to sort, match and combine the two k-space streams with respect to respiratory displacement. Reconstruction performance was quantified by (1) comparing the keyhole size (which corresponds to imaging speed) required to achieve the same image quality, and (2) maintaining a constant keyhole size across the three reconstruction methods to compare the resulting image quality to the ground truth image. Results: (1) The dynamic keyhole method required a mean keyhole size which was 48% smaller than the conventional keyhole technique and 60% smaller than the zero filling technique to achieve the same image quality. This directly corresponds to faster imaging. (2) When a constant keyhole size was utilized, the Dynamic Keyhole technique resulted in the smallest difference of the tumor region compared to the ground truth. Conclusion: The dynamic keyhole is a simple and adaptable technique for clinical applications requiring real-time imaging and tumor monitoring such as MRI guided radiotherapy. Based on the results from this study, the dynamic keyhole method could increase the imaging frequency by a factor of five compared with full k

The keyhole GTAW technology: a new welding technology joining quality and productivity

International Nuclear Information System (INIS)

Le Port, P.; Laugier, M.; Scandella, F.; Lawrjaniec, D.; Boucher, Ch.

2006-01-01

This paper is a literature review regarding the keyhole GTAW technology, which has been developed and first used for industrial applications in Australia. The process enables single pass welding of a wide range of materials including stainless steels, titanium and nickel alloys, up to 12 mm thick. Process parameters (welding current, arc voltage, travel speed, the type of shielding gas and tungsten electrode dimensions) are discussed with regards to keyhole formation and stability. A comparison between standard GTAW and keyhole GTAW is provided for the welding of 12 mm thick stainless steel and titanium, showing the substantial increase in productivity that can be achieved with this new technology. Institut de Soudure has taken part in a European project aimed at assessing the possibilities of the keyhole GTAW technology. (authors)

A three-dimensional sharp interface model for self-consistent keyhole and weld pool dynamics in deep penetration laser welding

International Nuclear Information System (INIS)

Pang Shengyong; Chen Liliang; Zhou Jianxin; Yin Yajun; Chen Tao

2011-01-01

A three-dimensional sharp interface model is proposed to investigate the self-consistent keyhole and weld pool dynamics in deep penetration laser welding. The coupling of three-dimensional heat transfer, fluid flow and keyhole free surface evolutions in the welding process is simulated. It is theoretically confirmed that under certain low heat input welding conditions deep penetration laser welding with a collapsing free keyhole could be obtained and the flow directions near the keyhole wall are upwards and approximately parallel to the keyhole wall. However, significantly different weld pool dynamics in a welding process with an unstable keyhole are numerically found. Many flow patterns in the welding process with an unstable keyhole, verified by x-ray transmission experiments, were successfully simulated and analysed. Periodical keyhole collapsing and bubble formation processes are also successfully simulated and believed to be in good agreement with experiments. The mechanisms of keyhole instability are found to be closely associated with the behaviour of humps on the keyhole wall, and it is found that the welding speed and surface tension are closely related to the formation of humps on the keyhole wall. It is also shown that the weld pool dynamics in laser welding with an unstable keyhole are closely associated with the transient keyhole instability and therefore modelling keyhole and weld pool in a self-consistent way is significant to understand the physics of laser welding.

Hearing preservation in retrosigmoid approach of small vestibular schwannomas: prognostic value of the degree of internal auditory canal filling.

Science.gov (United States)

Tringali, Stéphane; Ferber-Viart, Chantal; Fuchsmann, Carine; Buiret, Guillaume; Zaouche, Sandra; Dubreuil, Christian

2010-12-01

To assess the contribution of preoperative radiologic appearance of vestibular schwannoma (VS) on the magnetic resonance imaging in constructive interference in steady-state sequences and demonstrate if the degree of the internal auditory canal (IAC) filling is correlated with hearing and facial preservation. A group of 278 patients who underwent VS surgery in a tertiary referral center. Retrosigmoid approach surgery. Patients were classified in 4 groups according to the percentage of IAC filling on the preoperative magnetic resonance imaging as Group IAC 1(IAC empty or filled filled from 25% to 50% with free fundus), Group IAC 3 (IAC filled from 50% to 75% with free fundus), and Group IAC 4 (complete filling of the IAC without fundus obliteration). A good correlation was observed between the IAC classification and the rate of hearing and facial preservation. The global rate of postoperative facial palsy was 10.4%. The global rate of hearing preservation in 213 patients with preoperative hearing class A and B was 40.8%. Regression analysis showed that the degree of lateral extension of the VS in the IAC was a strong predictor of hearing preservation ( p facial outcomes in selected patients with possible hearing preservation. In case of patient with small tumor and IAC empty or filled less than 75% and with free fundus, surgery is the treatment of choice for patients with serviceable hearing and the desire to retain it.

Scaling of spiking and humping in keyhole welding

Energy Technology Data Exchange (ETDEWEB)

Wei, P S; Chuang, K C [Department of Mechanical and Electro-Mechanical Engineering, National Sun Yat-Sen University, Kaohsiung, Taiwan (China); DebRoy, T [Department of Materials Science and Engineering, The Pennsylvania State University, University Park, PA 16802 (United States); Ku, J S, E-mail: pswei@mail.nsysu.edu.tw, E-mail: cielo.zhuang@gmail.com, E-mail: rtd1@psu.edu, E-mail: jsku@mail.nsysu.edu.tw [Institute of Materials Science and Engineering, National Sun Yat-Sen University, Kaohsiung, Taiwan (China)

2011-06-22

Spiking, rippling and humping seriously reduce the strength of welds. The effects of beam focusing, volatile alloying element concentration and welding velocity on spiking, coarse rippling and humping in keyhole mode electron-beam welding are examined through scale analysis. Although these defects have been studied in the past, the mechanisms for their formation are not fully understood. This work relates the average amplitudes of spikes to fusion zone depth for the welding of Al 6061, SS 304 and carbon steel, and Al 5083. The scale analysis introduces welding and melting efficiencies and an appropriate power distribution to account for the focusing effects, and the energy which is reflected and escapes through the keyhole opening to the surroundings. The frequency of humping and spiking can also be predicted from the scale analysis. The analysis also reveals the interrelation between coarse rippling and humping. The data and the mechanistic findings reported in this study are useful for understanding and preventing spiking and humping during keyhole mode electron and laser beam welding.

Multiple Reflections and Fresnel Absorption of Gaussian Laser Beam in an Actual 3D Keyhole during Deep-Penetration Laser Welding

Directory of Open Access Journals (Sweden)

Xiangzhong Jin

2012-01-01

Full Text Available In deep penetration laser welding, a keyhole is formed in the material. Based on an experimentally obtained bending keyhole from low- and medium-speed laser penetration welding of glass, the keyhole profiles in both the symmetric plane are determined by polynomial fitting. Then, a 3D bending keyhole is reconstructed under the assumption of circular cross-section of the keyhole at each keyhole depth. In this paper, the behavior of focused Gaussian laser beam in the keyhole is analyzed by tracing a ray of light using Gaussian optics theory, the Fresnel absorption and multiple reflections in the keyhole are systematically studied, and the laser intensities absorbed on the keyhole walls are calculated. Finally, the formation mechanism of the keyhole is deduced.

Implementation of real-time multiple reflection and Fresnel absorption of laser beam in keyhole

International Nuclear Information System (INIS)

Cho, Jung-Ho; Na, Suck-Joo

2006-01-01

A computational analysis of laser keyhole welding is achieved. The main driving force to make the molten pool as a narrow and deep keyhole is the recoil pressure induced by evaporation of the material. Also, the multiple reflection effect on the keyhole wall plays an important role in making the keyhole deeper and raising its total energy absorption rate. Multiple reflection and Fresnel absorption are implemented simultaneously with the proposed ray tracing technique in a discrete grid cell system during the simulation for every single time step. In particular, the Fresnel absorption model is chosen as an energy transfer mechanism from laser beam to workpiece. With all the governing equations including continuity, momentum and energy equation, the VOF method is adopted to trace the free surface of the molten pool. Simulation results are compared with the experimental ones to verify its validity. A pulsed Nd : YAG laser was used for keyhole welding experiments on mild steel plates of 7 mm thickness. It was observed that the generated keyhole maintains its solidified shape without any closing phenomenon both in the experiments and in the simulations

Implementation of real-time multiple reflection and Fresnel absorption of laser beam in keyhole

Energy Technology Data Exchange (ETDEWEB)

Cho, Jung-Ho; Na, Suck-Joo [Department of Mechanical Engineering, KAIST, 373-1 Guseong-dong, Yuseong-gu, Daejeon 305-701 (Korea, Republic of)

2006-12-21

A computational analysis of laser keyhole welding is achieved. The main driving force to make the molten pool as a narrow and deep keyhole is the recoil pressure induced by evaporation of the material. Also, the multiple reflection effect on the keyhole wall plays an important role in making the keyhole deeper and raising its total energy absorption rate. Multiple reflection and Fresnel absorption are implemented simultaneously with the proposed ray tracing technique in a discrete grid cell system during the simulation for every single time step. In particular, the Fresnel absorption model is chosen as an energy transfer mechanism from laser beam to workpiece. With all the governing equations including continuity, momentum and energy equation, the VOF method is adopted to trace the free surface of the molten pool. Simulation results are compared with the experimental ones to verify its validity. A pulsed Nd : YAG laser was used for keyhole welding experiments on mild steel plates of 7 mm thickness. It was observed that the generated keyhole maintains its solidified shape without any closing phenomenon both in the experiments and in the simulations.

An Argument for the Keyhole Template for Close Air Support on the Urban Battlefield

Science.gov (United States)

2009-03-04

An Argument for the Keyhole Template for Close Air Support on the Urban Battlefield Captain BT Taggart Major RC... Keyhole Template for Close Air Support on the Urban Battlefield 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...graphic (GRG). Using the target building as the keyhole , or center of the engagement area, Lightning 62 requested a laser guided Maverick to destroy

Effect of keyhole characteristics on porosity formation during pulsed laser-GTA hybrid welding of AZ31B magnesium alloy

Science.gov (United States)

Chen, Minghua; Xu, Jiannan; Xin, Lijun; Zhao, Zuofu; Wu, Fufa; Ma, Shengnan; Zhang, Yue

2017-06-01

This paper experimentally investigates the relationship between laser keyhole characteristics on the porosity formation during pulsed laser-GTA welding of magnesium alloy. Based on direct observations during welding process, the influences of laser keyhole state on the porosity formation were studied. Results show that the porosities in the joint are always at the bottom of fusion zone of the joint, which is closely related to the keyhole behavior. A large depth to wide ratio always leads to the increase of porosity generation chance. Keeping the keyhole outlet open for a longer time benefits the porosity restriction. Overlap of adjacent laser keyhole can effectively decrease the porosity generation, due to the cutting effect between adjacent laser keyholes. There are threshold overlap rate values for laser keyholes in different state.

Modified skin incision for avoiding the lesser occipital nerve and occipital artery during retrosigmoid craniotomy: potential applications for enhancing operative working distance and angles while minimizing the risk of postoperative neuralgias and intraoperative hemorrhage.

Science.gov (United States)

Tubbs, R Shane; Fries, Fabian N; Kulwin, Charles; Mortazavi, Martin M; Loukas, Marios; Cohen-Gadol, Aaron A

2016-10-01

Chronic postoperative neuralgias and headache following retrosigmoid craniotomy can be uncomfortable for the patient. We aimed to better elucidate the regional nerve anatomy in an effort to minimize this postoperative complication. Ten adult cadaveric heads (20 sides) were dissected to observe the relationship between the lesser occipital nerve and a traditional linear versus modified U incision during retrosigmoid craniotomy. Additionally, the relationship between these incisions and the occipital artery were observed. The lesser occipital nerve was found to have two types of course. Type I nerves (60%) remained close to the posterior border of the sternocleidomastoid muscle and some crossed anteriorly over the sternocleidomastoid muscle near the mastoid process. Type II nerves (40%) left the posterior border of the sternocleidomastoid muscle and swung medially (up to 4.5cm posterior to the posterior border of the sternocleidomastoid muscle) as they ascended over the occiput. The lesser occipital nerve was near a midpoint of a line between the external occipital protuberance and mastoid process in all specimens with the type II nerve configuration. Based on our findings, the inverted U incision would be less likely to injure the type II nerves but would necessarily cross over type I nerves, especially more cranially on the nerve at the apex of the incision. As the more traditional linear incision would most likely transect the type I nerves and more so near their trunk, the U incision may be the overall better choice in avoiding neural and occipital artery injury during retrosigmoid approaches. Copyright © 2016 Elsevier Ltd. All rights reserved.

Keyhole imaging method for dynamic objects behind the occlusion area

Science.gov (United States)

Hao, Conghui; Chen, Xi; Dong, Liquan; Zhao, Yuejin; Liu, Ming; Kong, Lingqin; Hui, Mei; Liu, Xiaohua; Wu, Hong

2018-01-01

A method of keyhole imaging based on camera array is realized to obtain the video image behind a keyhole in shielded space at a relatively long distance. We get the multi-angle video images by using a 2×2 CCD camera array to take the images behind the keyhole in four directions. The multi-angle video images are saved in the form of frame sequences. This paper presents a method of video frame alignment. In order to remove the non-target area outside the aperture, we use the canny operator and morphological method to realize the edge detection of images and fill the images. The image stitching of four images is accomplished on the basis of the image stitching algorithm of two images. In the image stitching algorithm of two images, the SIFT method is adopted to accomplish the initial matching of images, and then the RANSAC algorithm is applied to eliminate the wrong matching points and to obtain a homography matrix. A method of optimizing transformation matrix is proposed in this paper. Finally, the video image with larger field of view behind the keyhole can be synthesized with image frame sequence in which every single frame is stitched. The results show that the screen of the video is clear and natural, the brightness transition is smooth. There is no obvious artificial stitching marks in the video, and it can be applied in different engineering environment .

Experimental research on the dynamic behaviors of the keyhole and molten pool in laser deep-penetration welding

Science.gov (United States)

Zhang, Yi; Lin, Qida; Yin, Xuni; Li, Simeng; Deng, Jiquan

2018-04-01

Both the morphology and temperature are two important characteristics of the keyhole and the molten pool in laser deep-penetration welding. The modified ‘sandwich’ method was adopted to overcome the difficulty in obtaining inner information about the keyhole and the molten pool. Based on this method, experimental platforms were built for observing the variations in the surface morphology, the longitudinal keyhole profile and the internal temperature. The experimental results of three dynamic behaviors exbibit as follows. The key factor, which makes the pool width go into a quasi-steady state, lies in the balance between the vortex and the sideways flows around the keyhole. Experimental observation shows that the keyhole goes through three stages in laser welding: the rapid drilling stage, the slow drilling stage and the quasi-steady state. The time for achieving a relative fixed keyhole depth is close to the formation time of the maximum pool width. The internal temperatures inside the keyhole and the molten pool first experience a rapid increase, then a decrease and finally go into a quasi-steady state. Compared to that in the unstable stage, the liquid–metal uphill formed in the stable stage of laser welding has less influence on the internal temperature.

Endoscopic and keyhole endoscope-assisted neurosurgical approaches: a qualitative survey on technical challenges and technological solutions.

Science.gov (United States)

Marcus, Hani J; Cundy, Thomas P; Hughes-Hallett, Archie; Yang, Guang-Zhong; Darzi, Ara; Nandi, Dipankar

2014-10-01

The literature reflects a resurgence of interest in endoscopic and keyhole endoscope-assisted neurosurgical approaches as alternatives to conventional microsurgical approaches in carefully selected cases. The aim of this study was to assess the technical challenges of neuroendoscopy, and the scope for technological innovations to overcome these barriers. All full members of the Society of British Neurosurgeons (SBNS) were electronically invited to participate in an online survey. The open-ended structured survey asked three questions; firstly, whether the surgeon presently utilises or has experience with endoscopic or endoscope-assisted approaches; secondly, what they consider to be the major technical barriers to adopting such approaches; and thirdly, what technological advances they foresee improving safety and efficacy in the field. Responses were subjected to a qualitative research method of multi-rater emergent theme analysis. Three clear themes emerged: 1) surgical approach and better integration with image-guidance systems (20%), 2) intra-operative visualisation and improvements in neuroendoscopy (49%), and 3) surgical manipulation and improvements in instruments (74%). The analysis of responses to our open-ended survey revealed that although opinion was varied three major themes could be identified. Emerging technological advances such as augmented reality, high-definition stereo-endoscopy, and robotic joint-wristed instruments may help overcome the technical difficulties associated with neuroendoscopic approaches. Results of this qualitative survey provide consensus amongst the technology end-user community such that unambiguous goals and priorities may be defined. Systems integrating these advances could improve the safety and efficacy of endoscopic and endoscope-assisted neurosurgical approaches.

A Technique for Resecting Occipital Pole Gliomas Using a Keyhole Lobectomy.

Science.gov (United States)

Conner, Andrew K; Baker, Cordell M; Briggs, Robert G; Burks, Joshua D; Glenn, Chad A; Smitherman, Adam D; Morgan, Jake P; Pittman, Nathan A; Sughrue, Michael E

2017-10-01

Our purpose is to describe a method of resecting occipital pole gliomas through a keyhole lobectomy and share the patient outcomes of this technique. We performed a retrospective review of data obtained on all patients who underwent resection of occipital pole gliomas by the senior author between 2012 and 2016. We describe our technique for resecting these tumors using a keyhole lobectomy and share the patient outcomes of this operation. Eight patients were included in this study. Four patients (50%) had not received previous surgery. One patient (13%) was diagnosed with a World Health Organization grade II tumor, and 7 patients (88%) were diagnosed with glioblastoma. Two tumors (25%) were left sided and 6 (75%) right sided. The median size of resection was 28 cm 3 . The median extent of resection was 96%, and at least 90% of the tumor was resected in all cases. None of the patients experienced permanent postoperative complications. Temporary neurologic complications included 3 patients (38%) with encephalopathy and 1 patient (13%) with aphasia. There were no neurosurgical complications. Our study provides details on the technical aspects of occipital keyhole lobectomies and gives the outcomes of patients who have received an operation for tumors in this uncommon location. Taking white matter tract anatomy into consideration, we show that the keyhole method can be applied to gliomas of the occipital lobe. Copyright © 2017 Elsevier Inc. All rights reserved.

Dynamics of vapor plume in transient keyhole during laser welding of stainless steel: Local evaporation, plume swing and gas entrapment into porosity

Science.gov (United States)

Pang, Shengyong; Chen, Xin; Shao, Xinyu; Gong, Shuili; Xiao, Jianzhong

2016-07-01

In order to better understand the local evaporation phenomena of keyhole wall, vapor plume swing above the keyhole and ambient gas entrapment into the porosity defects, the 3D time-dependent dynamics of the metallic vapor plume in a transient keyhole during fiber laser welding is numerically investigated. The vapor dynamical parameters, including the velocity and pressure, are successfully predicted and obtain good agreements with the experimental and literature data. It is found that the vapor plume flow inside the keyhole has complex multiple directions, and this various directions characteristic of the vapor plume is resulted from the dynamic evaporation phenomena with variable locations and orientations on the keyhole wall. The results also demonstrate that because of this dynamic local evaporation, the ejected vapor plume from the keyhole opening is usually in high frequency swinging. The results further indicate that the oscillation frequency of the plume swing angle is around 2.0-8.0 kHz, which is of the same order of magnitude with that of the keyhole depth (2.0-5.0 kHz). This consistency clearly shows that the swing of the ejected vapor plume is closely associated with the keyhole instability during laser welding. Furthermore, it is learned that there is usually a negative pressure region (several hundred Pa lower than the atmospheric pressure) of the vapor flow around the keyhole opening. This pressure could lead to a strong vortex flow near the rear keyhole wall, especially when the velocity of the ejected metallic vapor from the keyhole opening is high. Under the effect of this flow, the ambient gas is involved into the keyhole, and could finally be entrapped into the bubbles within a very short time (keyhole.

On the Keyhole Hypothesis: High Mutual Information between Ear and Scalp EEG

Directory of Open Access Journals (Sweden)

Kaare B. Mikkelsen

2017-06-01

Full Text Available We propose and test the keyhole hypothesis—that measurements from low dimensional EEG, such as ear-EEG reflect a broadly distributed set of neural processes. We formulate the keyhole hypothesis in information theoretical terms. The experimental investigation is based on legacy data consisting of 10 subjects exposed to a battery of stimuli, including alpha-attenuation, auditory onset, and mismatch-negativity responses and a new medium-long EEG experiment involving data acquisition during 13 h. Linear models were estimated to lower bound the scalp-to-ear capacity, i.e., predicting ear-EEG data from simultaneously recorded scalp EEG. A cross-validation procedure was employed to ensure unbiased estimates. We present several pieces of evidence in support of the keyhole hypothesis: There is a high mutual information between data acquired at scalp electrodes and through the ear-EEG “keyhole,” furthermore we show that the view—represented as a linear mapping—is stable across both time and mental states. Specifically, we find that ear-EEG data can be predicted reliably from scalp EEG. We also address the reverse view, and demonstrate that large portions of the scalp EEG can be predicted from ear-EEG, with the highest predictability achieved in the temporal regions and when using ear-EEG electrodes with a common reference electrode.

Improving Keyhole Stability by External Magnetic Field in Full Penetration Laser Welding

Science.gov (United States)

Li, Min; Xu, Jiajun; Huang, Yu; Rong, Youmin

2018-05-01

An external magnetic field was used to improve the keyhole stability in full penetration laser welding 316L steel. The increase of magnetic field strength gave rise to a shorter flying time of the spatter, a weaker size and brightness of the spatter, and a larger spreading area of vapor plume. This suggested that the dynamic behavior of the keyhole was stabilized by the external magnetic field. In addition, a stronger magnetic field could result in a more homogeneous distribution of laser energy, which increased the width of the weld zone, and the height of the bottom weld zone from 381 μm (0 mT) to 605 μm (50 mT). Dendrite and cellular crystal near the weld center disappeared, and grain size was refined. The external magnetic field was beneficial to the keyhole stability and improved the joint quality, because the weld pool was stirred by a Lorentz force resulting from the coupling effect of the magnetic field and inner thermocurrent.

Quantifying the accuracy of the tumor motion and area as a function of acceleration factor for the simulation of the dynamic keyhole magnetic resonance imaging method

Energy Technology Data Exchange (ETDEWEB)

Lee, Danny; Pollock, Sean; Keall, Paul, E-mail: paul.keall@sydney.edu.au [Radiation Physics Laboratory, Sydney Medical School, University of Sydney, Sydney, NSW 2006 (Australia); Greer, Peter B. [School of Mathematical and Physical Sciences, University of Newcastle, Newcastle, NSW 2308, Australia and Department of Radiation Oncology, Calvary Mater Newcastle Hospital, Newcastle, NSW 2298 (Australia); Kim, Taeho [Radiation Physics Laboratory, Sydney Medical School, University of Sydney, Sydney, NSW 2006, Australia and Department of Radiation Oncology, Virginia Commonwealth University, Richmond, Virginia 23219 (United States)

2016-05-15

Purpose: The dynamic keyhole is a new MR image reconstruction method for thoracic and abdominal MR imaging. To date, this method has not been investigated with cancer patient magnetic resonance imaging (MRI) data. The goal of this study was to assess the dynamic keyhole method for the task of lung tumor localization using cine-MR images reconstructed in the presence of respiratory motion. Methods: The dynamic keyhole method utilizes a previously acquired a library of peripheral k-space datasets at similar displacement and phase (where phase is simply used to determine whether the breathing is inhale to exhale or exhale to inhale) respiratory bins in conjunction with central k-space datasets (keyhole) acquired. External respiratory signals drive the process of sorting, matching, and combining the two k-space streams for each respiratory bin, thereby achieving faster image acquisition without substantial motion artifacts. This study was the first that investigates the impact of k-space undersampling on lung tumor motion and area assessment across clinically available techniques (zero-filling and conventional keyhole). In this study, the dynamic keyhole, conventional keyhole and zero-filling methods were compared to full k-space dataset acquisition by quantifying (1) the keyhole size required for central k-space datasets for constant image quality across sixty four cine-MRI datasets from nine lung cancer patients, (2) the intensity difference between the original and reconstructed images in a constant keyhole size, and (3) the accuracy of tumor motion and area directly measured by tumor autocontouring. Results: For constant image quality, the dynamic keyhole method, conventional keyhole, and zero-filling methods required 22%, 34%, and 49% of the keyhole size (P < 0.0001), respectively, compared to the full k-space image acquisition method. Compared to the conventional keyhole and zero-filling reconstructed images with the keyhole size utilized in the dynamic keyhole

Quantifying the accuracy of the tumor motion and area as a function of acceleration factor for the simulation of the dynamic keyhole magnetic resonance imaging method.

Science.gov (United States)

Lee, Danny; Greer, Peter B; Pollock, Sean; Kim, Taeho; Keall, Paul

2016-05-01

The dynamic keyhole is a new MR image reconstruction method for thoracic and abdominal MR imaging. To date, this method has not been investigated with cancer patient magnetic resonance imaging (MRI) data. The goal of this study was to assess the dynamic keyhole method for the task of lung tumor localization using cine-MR images reconstructed in the presence of respiratory motion. The dynamic keyhole method utilizes a previously acquired a library of peripheral k-space datasets at similar displacement and phase (where phase is simply used to determine whether the breathing is inhale to exhale or exhale to inhale) respiratory bins in conjunction with central k-space datasets (keyhole) acquired. External respiratory signals drive the process of sorting, matching, and combining the two k-space streams for each respiratory bin, thereby achieving faster image acquisition without substantial motion artifacts. This study was the first that investigates the impact of k-space undersampling on lung tumor motion and area assessment across clinically available techniques (zero-filling and conventional keyhole). In this study, the dynamic keyhole, conventional keyhole and zero-filling methods were compared to full k-space dataset acquisition by quantifying (1) the keyhole size required for central k-space datasets for constant image quality across sixty four cine-MRI datasets from nine lung cancer patients, (2) the intensity difference between the original and reconstructed images in a constant keyhole size, and (3) the accuracy of tumor motion and area directly measured by tumor autocontouring. For constant image quality, the dynamic keyhole method, conventional keyhole, and zero-filling methods required 22%, 34%, and 49% of the keyhole size (P lung tumor monitoring applications. This study demonstrates that the dynamic keyhole method is a promising technique for clinical applications such as image-guided radiation therapy requiring the MR monitoring of thoracic tumors. Based

Combined supra-transorbital keyhole approach for treatment of delayed intraorbital encephalocele: A minimally invasive approach for an unusual complication of decompressive craniectomy

Science.gov (United States)

di Somma, Lucia; Iacoangeli, Maurizio; Nasi, Davide; Balercia, Paolo; Lupi, Ettore; Girotto, Riccardo; Polonara, Gabriele; Scerrati, Massimo

2016-01-01

Background: Intraorbital encephalocele is a rare entity characterized by the herniation of cerebral tissue inside the orbital cavity through a defect of the orbital roof. In patients who have experienced head trauma, intraorbital encephalocele is usually secondary to orbital roof fracture. Case Description: We describe here a case of a patient who presented an intraorbital encephalocele 2 years after severe traumatic brain injury, treated by decompressive craniectomy and subsequent autologous cranioplasty, without any evidence of orbital roof fracture. The encephalocele removal and the subsequent orbital roof reconstruction were performed by using a modification of the supraorbital keyhole approach, in which we combine an orbital osteotomy with a supraorbital minicraniotomy to facilitate view and access to both the anterior cranial fossa and orbital compartment and to preserve the already osseointegrated autologous cranioplasty. Conclusions: The peculiarities of this case are the orbital encephalocele without an orbital roof traumatic fracture, and the combined minimally invasive approach used to fix both the encephalocele and the orbital roof defect. Delayed intraorbital encephalocele is probably a complication related to an unintentional opening of the orbit during decompressive craniectomy through which the brain herniated following the restoration of physiological intracranial pressure gradients after the bone flap repositioning. The reconstruction of the orbital roof was performed by using a combined supra-transorbital minimally invasive approach aiming at achieving adequate surgical exposure while preserving the autologous cranioplasty, already osteointegrated. To the best of our knowledge, this approach has not been previously used to address intraorbital encephalocele. PMID:26862452

A quantitative trait locus for a primary antibody response to keyhole limpet hemocyanin on chicken chromosome 14-Confirmation and candidate gene approach

NARCIS (Netherlands)

Siwek, M.; Slawinska, A.; Nieuwland, M.G.B.; Witkowski, A.; Zieba, G.; Minozzi, G.; Knol, E.F.; Bednarczyk, M.

2010-01-01

A QTL involved in the primary antibody response toward keyhole limpet hemocyanin (KLH) was detected on chicken chromosome 14 in the experimental population, which was created by crossing commercial White Leghorn and a Polish native chicken breed (green-legged partridgelike). The current QTL location

Keyhole formation and thermal fluid flow-induced porosity during laser fusion welding in titanium alloys: Experimental and modelling

International Nuclear Information System (INIS)

Panwisawas, Chinnapat; Perumal, Bama; Ward, R. Mark; Turner, Nathanael; Turner, Richard P.; Brooks, Jeffery W.; Basoalto, Hector C.

2017-01-01

High energy-density beam welding, such as electron beam or laser welding, has found a number of industrial applications for clean, high-integrity welds. The deeply penetrating nature of the joints is enabled by the formation of metal vapour which creates a narrow fusion zone known as a “keyhole”. However the formation of the keyhole and the associated keyhole dynamics, when using a moving laser heat source, requires further research as they are not fully understood. Porosity, which is one of a number of process induced phenomena related to the thermal fluid dynamics, can form during beam welding processes. The presence of porosity within a welded structure, inherited from the fusion welding operation, degrades the mechanical properties of components during service such as fatigue life. In this study, a physics-based model for keyhole welding including heat transfer, fluid flow and interfacial interactions has been used to simulate keyhole and porosity formation during laser welding of Ti-6Al-4V titanium alloy. The modelling suggests that keyhole formation and the time taken to achieve keyhole penetration can be predicted, and it is important to consider the thermal fluid flow at the melting front as this dictates the evolution of the fusion zone. Processing induced porosity is significant when the fusion zone is only partially penetrating through the thickness of the material. The modelling results are compared with high speed camera imaging and measurements of porosity from welded samples using X-ray computed tomography, radiography and optical micrographs. These are used to provide a better understanding of the relationship between process parameters, component microstructure and weld integrity.

Vertical diplopia and oscillopsia due to midbrain keyhole aqueduct syndrome associated with severe cough

Directory of Open Access Journals (Sweden)

Angela Jinsook Oh

2018-06-01

Full Text Available Purpose: Midline structural defects in the neural axis can give rise to neuro-ophthalmic symptoms. We report a rare case of keyhole aqueduct syndrome presenting after two years of severe cough due to gastroesophageal reflux disease. Observations: A 58-year-old woman with a 2-year history of daily, severe cough presented to the neuro-ophthalmology clinic with progressive diplopia and oscillopsia. Examination revealed a 1–2 Hz down-beating nystagmus in primary gaze that worsened with left, right, and down gazes. Gaze evoked nystagmus and mild paresis were also seen with up gaze. There was an incomitant left hypertropia due to skew deviation that worsened with right and up gazes and improved with down gaze. She also had a right-sided ptosis and a 3 mm anisocoria not due to cranial nerve 3 paresis or Horner's syndrome. Brain magnetic resonance imaging showed a 1.5 mm × 11.7 mm × 6 mm midline cleft in the ventral midbrain communicating with the cerebral aqueduct, consistent with keyhole aqueduct syndrome. Her nystagmus and diplopia improved with oral acetazolamide treatment, at high doses of 2500–3000 mg per day. Conclusions and importance: We report the first case of midbrain keyhole aqueduct syndrome with ocular motor and other neuro-ophthalmic manifestations associated with severe cough. Although her cough was effectively treated and intracranial pressure measurement was normal, her ophthalmic symptoms continued to progress, which is common in previous cases reported. Treatment with acetazolamide led to significant improvement, supporting the use of acetazolamide in this rare condition. Keywords: Keyhole aqueduct syndrome, Midbrain cleft, Mesencephalic cleft, Syrinx, Syringobulbia, Down-beating nystagmus, Cerebrospinal fluid

The keyhole GTAW technology: a new welding technology joining quality and productivity; Le procede K-TIG: une nouvelle technologie de soudage combinant qualite et productivite

Energy Technology Data Exchange (ETDEWEB)

Le Port, P.; Laugier, M.; Scandella, F.; Lawrjaniec, D. [Institut de Soudure, 57 - Yutz (France); Boucher, Ch. [Institut de Soudure, 93 - Villepinte (France)

2006-05-15

This paper is a literature review regarding the keyhole GTAW technology, which has been developed and first used for industrial applications in Australia. The process enables single pass welding of a wide range of materials including stainless steels, titanium and nickel alloys, up to 12 mm thick. Process parameters (welding current, arc voltage, travel speed, the type of shielding gas and tungsten electrode dimensions) are discussed with regards to keyhole formation and stability. A comparison between standard GTAW and keyhole GTAW is provided for the welding of 12 mm thick stainless steel and titanium, showing the substantial increase in productivity that can be achieved with this new technology. Institut de Soudure has taken part in a European project aimed at assessing the possibilities of the keyhole GTAW technology. (authors)

Tailoring weld geometry during keyhole mode laser welding using a genetic algorithm and a heat transfer model

International Nuclear Information System (INIS)

Rai, R; DebRoy, T

2006-01-01

Tailoring of weld attributes based on scientific principles remains an important goal in welding research. The current generation of unidirectional laser keyhole models cannot determine sets of welding variables that can lead to a particular weld attribute such as specific weld geometry. Here we show how a computational heat transfer model of keyhole mode laser welding can be restructured for systematic tailoring of weld attributes based on scientific principles. Furthermore, the model presented here can calculate multiple sets of laser welding variables, i.e. laser power, welding speed and beam defocus, with each set leading to the same weld pool geometry. Many sets of welding variables were obtained via a global search using a real number-based genetic algorithm, which was combined with a numerical heat transfer model of keyhole laser welding. The reliability of the numerical heat transfer calculations was significantly improved by optimizing values of the uncertain input parameters from a limited volume of experimental data. The computational procedure was applied to the keyhole mode laser welding of the 5182 Al-Mg alloy to calculate various sets of welding variables to achieve a specified weld geometry. The calculated welding parameter sets showed wide variations of the values of welding parameters, but each set resulted in a similar fusion zone geometry. The effectiveness of the computational procedure was examined by comparing the computed weld geometry for each set of welding parameters with the corresponding experimental geometry. The results provide hope that systematic tailoring of weld attributes via multiple pathways, each representing alternative welding parameter sets, is attainable based on scientific principles

Keyhole behavior and liquid flow in molten pool during laser-arc hybrid welding

Science.gov (United States)

Naito, Yasuaki; Katayama, Seiji; Matsunawa, Akira

2003-03-01

Hybrid welding was carried out on Type 304 stainless steel plate under various conditions using YAG laser combined with TIG arc. During arc and laser-arc hybrid welding, arc voltage variation was measured, and arc plasma, laser-induced plume and evaporation spots as well as keyhole behavior and liquid flow in the molten pool were observed through CCD camera and X-ray real-time transmission apparatus. It was consequently found that hybrid welding possessed many features in comparison with YAG laser welding. The deepest weld bead could be produced when the YAG laser beam of high power density was shot on the molten pool made beforehand stably with TIG arc. A keyhole was long and narrow, and its behavior was rather stable inside the molten pool. It was also confirmed that porosity was reduced by the suppression of bubble formation in hybrid welding utilizing a laser of a moderate power density.

Investigation of mixing and diffusion processes in hybrid spot laser-MIG keyhole welding

International Nuclear Information System (INIS)

Zhou, J; Tsai, H L

2009-01-01

In hybrid laser-MIG keyhole welding, anti-crack elements can be added into the weld pool through a filler metal in anticipation of compensating mass loss, preventing porosity formation and improving compositional and mechanical properties of the welds. Understanding the mixing and diffusion of the filler metal in the molten pool is vital to achieve these desired objectives. In this study, mathematical models and associated numerical techniques have been developed to investigate the mixing and diffusion processes in hybrid laser-MIG keyhole welding. The transient interactions between droplets and weld pool and dynamics of the melt flow are studied. The effects of key process parameters, such as droplet size (wire diameter), droplet generation frequency (wire feed speed) and droplet impinging speed, on mixing/diffusion are systematically investigated. It was found that compositional homogeneity of the weld pool is determined by the competition between the mixing rate and the solidification rate. A small-size filler droplet together with high generation frequency can increase the latitudinal diffusion of the filler metal into the weld pool, while the large-size droplet along with the low generation frequency helps to get more uniform longitudinal diffusion. Increasing the impinging velocity of the filler droplet can improve the latitudinal diffusion of the filler metal. However, a high impinging velocity can cause a lower diffusion zone in the upper part of the welds. This study provides a good foundation for optimizing the hybrid laser-MIG keyhole welding process to achieve quality welds with desired properties.

Experimental investigation on the weld pool formation process in plasma keyhole arc welding

Science.gov (United States)

Van Anh, Nguyen; Tashiro, Shinichi; Van Hanh, Bui; Tanaka, Manabu

2018-01-01

This paper seeks to clarify the weld pool formation process in plasma keyhole arc welding (PKAW). We adopted, for the first time, the measurement of the 3D convection inside the weld pool in PKAW by stereo synchronous imaging of tungsten tracer particles using two sets of x-ray transmission systems. The 2D convection on the weld pool surface was also measured using zirconia tracer particles. Through these measurements, the convection in a wide range of weld pools from the vicinity of the keyhole to the rear region was successfully visualized. In order to discuss the heat transport process in a weld pool, the 2D temperature distribution on the weld pool surface was also measured by two-color pyrometry. The results of the comprehensive experimental measurement indicate that the shear force due to plasma flow is found to be the dominant driving force in the weld pool formation process in PKAW. Thus, heat transport in a weld pool is considered to be governed by two large convective patterns near the keyhole: (1) eddy pairs on the surface (perpendicular to the torch axis), and (2) eddy pairs on the bulk of the weld pool (on the plane of the torch). They are formed with an equal velocity of approximately 0.35 m s-1 and are mainly driven by shear force. Furthermore, the flow velocity of the weld pool convection becomes considerably higher than that of other welding processes, such as TIG welding and GMA welding, due to larger plasma flow velocity.

Towards Fast Tracking of the Keyhole Geometry

Science.gov (United States)

Brock, C.; Hohenstein, R.; Schmidt, M.

We describe a sensor principle permitting the fast online measurement of the position of the optical process emissions in deep penetration laser welding. Experiments show a strong correlation between the position of the vapour plume and the keyhole geometry, demonstrated here by varying the penetration depth of the weld. In order to achieve an absolute position measurement, the sensor was calibrated using a light source with well defined characteristics. The setup for the calibration measurements and the corresponding data evaluation methods are discussed. The precision of the calibration with a green LED is 6 μm in lateral and 55 μm in axial direction, for a working distance of 200 mm.

3D Simulations of the ``Keyhole'' Hohlraum for Shock Timing on NIF

Science.gov (United States)

Robey, H. F.; Marinak, M. M.; Munro, D. H.; Jones, O. S.

2007-11-01

Ignition implosions planned for the National Ignition Facility (NIF) require a pulse shape with a carefully designed series of steps, which launch a series of shocks through the ablator and DT fuel. The relative timing of these shocks must be tuned to better than +/- 100ps to maintain the DT fuel on a sufficiently low adiabat. To meet these requirements, pre-ignition tuning experiments using a modified hohlraum geometry are being planned. This modified geometry, known as the ``keyhole'' hohlraum, adds a re-entrant gold cone, which passes through the hohlraum and capsule walls, to provide an optical line-of-sight to directly measure the shocks as they break out of the ablator. In order to assess the surrogacy of this modified geometry, 3D simulations using HYDRA [1] have been performed. The drive conditions and the resulting effect on shock timing in the keyhole hohlraum will be compared with the corresponding results for the standard ignition hohlraum. [1] M.M. Marinak, et al., Phys. Plasmas 8, 2275 (2001).

Geospatial Visualization of Scientific Data Through Keyhole Markup Language

Science.gov (United States)

Wernecke, J.; Bailey, J. E.

2008-12-01

The development of virtual globes has provided a fun and innovative tool for exploring the surface of the Earth. However, it has been the paralleling maturation of Keyhole Markup Language (KML) that has created a new medium and perspective through which to visualize scientific datasets. Originally created by Keyhole Inc., and then acquired by Google in 2004, in 2007 KML was given over to the Open Geospatial Consortium (OGC). It became an OGC international standard on 14 April 2008, and has subsequently been adopted by all major geobrowser developers (e.g., Google, Microsoft, ESRI, NASA) and many smaller ones (e.g., Earthbrowser). By making KML a standard at a relatively young stage in its evolution, developers of the language are seeking to avoid the issues that plagued the early World Wide Web and development of Hypertext Markup Language (HTML). The popularity and utility of Google Earth, in particular, has been enhanced by KML features such as the Smithsonian volcano layer and the dynamic weather layers. Through KML, users can view real-time earthquake locations (USGS), view animations of polar sea-ice coverage (NSIDC), or read about the daily activities of chimpanzees (Jane Goodall Institute). Perhaps even more powerful is the fact that any users can create, edit, and share their own KML, with no or relatively little knowledge of manipulating computer code. We present an overview of the best current scientific uses of KML and a guide to how scientists can learn to use KML themselves.

Vision-based weld pool boundary extraction and width measurement during keyhole fiber laser welding

Science.gov (United States)

Luo, Masiyang; Shin, Yung C.

2015-01-01

In keyhole fiber laser welding processes, the weld pool behavior is essential to determining welding quality. To better observe and control the welding process, the accurate extraction of the weld pool boundary as well as the width is required. This work presents a weld pool edge detection technique based on an off axial green illumination laser and a coaxial image capturing system that consists of a CMOS camera and optic filters. According to the difference of image quality, a complete developed edge detection algorithm is proposed based on the local maximum gradient of greyness searching approach and linear interpolation. The extracted weld pool geometry and the width are validated by the actual welding width measurement and predictions by a numerical multi-phase model.

Vertical diplopia and oscillopsia due to midbrain keyhole aqueduct syndrome associated with severe cough.

Science.gov (United States)

Oh, Angela Jinsook; Lanzman, Bryan Alexander; Liao, Yaping Joyce

2018-06-01

Midline structural defects in the neural axis can give rise to neuro-ophthalmic symptoms. We report a rare case of keyhole aqueduct syndrome presenting after two years of severe cough due to gastroesophageal reflux disease. A 58-year-old woman with a 2-year history of daily, severe cough presented to the neuro-ophthalmology clinic with progressive diplopia and oscillopsia. Examination revealed a 1-2 Hz down-beating nystagmus in primary gaze that worsened with left, right, and down gazes. Gaze evoked nystagmus and mild paresis were also seen with up gaze. There was an incomitant left hypertropia due to skew deviation that worsened with right and up gazes and improved with down gaze. She also had a right-sided ptosis and a 3 mm anisocoria not due to cranial nerve 3 paresis or Horner's syndrome. Brain magnetic resonance imaging showed a 1.5 mm × 11.7 mm × 6 mm midline cleft in the ventral midbrain communicating with the cerebral aqueduct, consistent with keyhole aqueduct syndrome. Her nystagmus and diplopia improved with oral acetazolamide treatment, at high doses of 2500-3000 mg per day. We report the first case of midbrain keyhole aqueduct syndrome with ocular motor and other neuro-ophthalmic manifestations associated with severe cough. Although her cough was effectively treated and intracranial pressure measurement was normal, her ophthalmic symptoms continued to progress, which is common in previous cases reported. Treatment with acetazolamide led to significant improvement, supporting the use of acetazolamide in this rare condition.

Improvement of laser keyhole formation with the assistance of arc plasma in the hybrid welding process of magnesium alloy

Science.gov (United States)

Liu, Liming; Hao, Xinfeng

2009-11-01

In the previous work, low-power laser/arc hybrid welding technique is used to weld magnesium alloy and high-quality weld joints are obtained. In order to make clear the interactions between low-power laser pulse and arc plasma, the effect of arc plasma on laser pulse is studied in this article. The result shows that the penetration of low-power laser welding with the assistance of TIG arc is more than two times deeper than that of laser welding alone and laser welding transforms from thermal-conduction mode to keyhole mode. The plasma behaviors and spectra during the welding process are studied, and the transition mechanism of laser-welding mode is analyzed in detail. It is also found that with the assistance of arc plasma, the threshold value of average power density to form keyhole welding for YAG laser is only 3.3×10 4 W/cm 2, and the average peak power density is 2.6×10 5 W/cm 2 in the present experiment. Moreover, the distribution of energy density during laser pulse is modulated to improve the formation and stability of laser keyholes.

Successful Treatment with Microvascular Decompression Surgery of a Patient with Hemiparesis Caused by Vertebral Artery Compression of the Medulla Oblongata: Case Report and Review of the Literature.

Science.gov (United States)

Ren, Jibin; Sun, Hongtao; Diao, Yunfeng; Niu, Xuegang; Wang, Hang; Wei, Zhengjun; Yuan, Fei

2017-12-01

There are few reports on hemiparesis caused by vascular medullary compression, which can occur because of dolichoectasia of the vertebrobasilar arterial system. In this article, we report a case of vertebral artery compression of the medulla oblongata in a 67-year-old woman. The patient was hypertensive, and she developed hemiparesis and intermittent spasms over 5 years. These spasms had worsened during the last year. Cranial nerve magnetic resonance imaging showed compression of the medulla oblongata by the left vertebral artery. A motor evoked potential (MEP) examination showed abnormal conduction of MEPs of bilateral toe abductors. The patient underwent microvascular decompression surgery under general anesthesia through a retrosigmoid keyhole approach. This operation led to relief of vascular compression and symptomatic improvement. Our case suggests that detailed history, imaging studies, and electrophysiologic studies help lead to a correct and early diagnosis of hemiparesis caused by vascular compression of the rostral ventrolateral medulla. Microvascular decompression surgery improves patient symptoms, and intraoperative electrophysiologic monitoring helps to avoid injury to important adjacent nerves. Copyright © 2017 Elsevier Inc. All rights reserved.

On the performance of dual-hop systems with multiple antennas: Effects of spatial correlation, keyhole, and co-channel interference

KAUST Repository

Yang, Liang

2012-12-01

In this paper, taking into account realistic propagation conditions, namely, spatial correlation, keyhole channels, and unequal-power co-channel interference, we investigate the performance of a wireless relay network where all the nodes are equipped with multiple antennas. Considering channel state information assisted amplify-and-forward protocol, we present analytical expressions for the symbol error rate (SER) and outage probability. More specifically, we first derive the SER expressions of a relay system with orthogonal space-time block coding (OSTBC) over correlated/keyhole fading channels. We also analyze the outage probability of interference corrupted relay systems with maximal ratio combing (MRC) at the receiver as well as multiple-input multiple-output MRC (MIMO MRC). Numerical results are given to illustrate and verify the analytical results. © 2012 IEEE.

On the performance of dual-hop systems with multiple antennas: Effects of spatial correlation, keyhole, and co-channel interference

KAUST Repository

Yang, Liang; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Liu, Weiping

2012-01-01

In this paper, taking into account realistic propagation conditions, namely, spatial correlation, keyhole channels, and unequal-power co-channel interference, we investigate the performance of a wireless relay network where all the nodes are equipped with multiple antennas. Considering channel state information assisted amplify-and-forward protocol, we present analytical expressions for the symbol error rate (SER) and outage probability. More specifically, we first derive the SER expressions of a relay system with orthogonal space-time block coding (OSTBC) over correlated/keyhole fading channels. We also analyze the outage probability of interference corrupted relay systems with maximal ratio combing (MRC) at the receiver as well as multiple-input multiple-output MRC (MIMO MRC). Numerical results are given to illustrate and verify the analytical results. © 2012 IEEE.

View-sharing in keyhole imaging: Partially compressed central k-space acquisition in time-resolved MRA at 3.0 T

International Nuclear Information System (INIS)

Hadizadeh, Dariusch R.; Gieseke, Juergen; Beck, Gabriele; Geerts, Liesbeth; Kukuk, Guido M.; Bostroem, Azize; Urbach, Horst; Schild, Hans H.; Willinek, Winfried A.

2011-01-01

Introduction: Time-resolved contrast-enhanced magnetic resonance (MR) angiography (CEMRA) of the intracranial vasculature has proved its clinical value for the evaluation of cerebral vascular disease in cases where both flow hemodynamics and morphology are important. The purpose of this study was to evaluate a combination of view-sharing with keyhole imaging to increase spatial and temporal resolution of time-resolved CEMRA at 3.0 T. Methods: Alternating view-sharing was combined with randomly segmented k-space ordering, keyhole imaging, partial Fourier and parallel imaging (4DkvsMRA). 4DkvsMRA was evaluated using varying compression factors (80-100) resulting in spatial resolutions ranging from (1.1 x 1.1 x 1.4) to (0.96 x 0.96 x 0.95) mm 3 and temporal resolutions ranging from 586 ms/dynamic scan - 288 ms/dynamic scan in three protocols in 10 healthy volunteers and seven patients (17 subjects). DSA correlation was available in four patients with cerebral arteriovenous malformations (cAVMs) and one patient with cerebral teleangiectasia. Results: 4DkvsMRA was successfully performed in all subjects and showed clear depiction of arterial and venous phases with diagnostic image quality. At the maximum view-sharing compression factor (=100), a 'flickering' artefact was observed. Conclusion: View-sharing in keyhole imaging allows for increased spatial and temporal resolution in time-resolved MRA.

View-sharing in keyhole imaging: Partially compressed central k-space acquisition in time-resolved MRA at 3.0 T

Energy Technology Data Exchange (ETDEWEB)

Hadizadeh, Dariusch R., E-mail: Dariusch.Hadizadeh@ukb.uni-bonn.de [University of Bonn, Department of Radiology, Sigmund-Freud-Strasse 25, 53127 Bonn (Germany); Gieseke, Juergen [University of Bonn, Department of Radiology, Sigmund-Freud-Strasse 25, 53127 Bonn (Germany); Philips Healthcare, Best (Netherlands); Beck, Gabriele; Geerts, Liesbeth [Philips Healthcare, Best (Netherlands); Kukuk, Guido M. [University of Bonn, Department of Radiology, Sigmund-Freud-Strasse 25, 53127 Bonn (Germany); Bostroem, Azize [Department of Neurosurgery, Sigmund-Freud-Strasse 25, 53127 Bonn, Deutschland (Germany); Urbach, Horst; Schild, Hans H.; Willinek, Winfried A. [University of Bonn, Department of Radiology, Sigmund-Freud-Strasse 25, 53127 Bonn (Germany)

2011-11-15

Introduction: Time-resolved contrast-enhanced magnetic resonance (MR) angiography (CEMRA) of the intracranial vasculature has proved its clinical value for the evaluation of cerebral vascular disease in cases where both flow hemodynamics and morphology are important. The purpose of this study was to evaluate a combination of view-sharing with keyhole imaging to increase spatial and temporal resolution of time-resolved CEMRA at 3.0 T. Methods: Alternating view-sharing was combined with randomly segmented k-space ordering, keyhole imaging, partial Fourier and parallel imaging (4DkvsMRA). 4DkvsMRA was evaluated using varying compression factors (80-100) resulting in spatial resolutions ranging from (1.1 x 1.1 x 1.4) to (0.96 x 0.96 x 0.95) mm{sup 3} and temporal resolutions ranging from 586 ms/dynamic scan - 288 ms/dynamic scan in three protocols in 10 healthy volunteers and seven patients (17 subjects). DSA correlation was available in four patients with cerebral arteriovenous malformations (cAVMs) and one patient with cerebral teleangiectasia. Results: 4DkvsMRA was successfully performed in all subjects and showed clear depiction of arterial and venous phases with diagnostic image quality. At the maximum view-sharing compression factor (=100), a 'flickering' artefact was observed. Conclusion: View-sharing in keyhole imaging allows for increased spatial and temporal resolution in time-resolved MRA.

TH-EF-BRA-05: A Method of Near Real-Time 4D MRI Using Volumetric Dynamic Keyhole (VDK) in the Presence of Respiratory Motion for MR-Guided Radiotherapy

International Nuclear Information System (INIS)

Lewis, B; Kim, S; Kim, T

2016-01-01

Purpose: To develop a novel method that enables 4D MR imaging in near real-time for continuous monitoring of tumor motion in MR-guided radiotherapy. Methods: This method is mainly based on an idea of expanding dynamic keyhole to full volumetric imaging acquisition. In the VDK approach introduced in this study, a library of peripheral volumetric k-space data is generated in given number of phases (5 and 10 in this study) in advance. For 4D MRI at any given time, only volumetric central k-space data are acquired in real-time and combined with pre-acquired peripheral volumetric k-space data in the library corresponding to the respiratory phase (or amplitude). The combined k-space data are Fourier-transformed to MR images. For simulation study, an MRXCAT program was used to generate synthetic MR images of the thorax with desired respiratory motion, contrast levels, and spatial and temporal resolution. 20 phases of volumetric MR images, with 200 ms temporal resolution in 4 s respiratory period, were generated using balanced steady-state free precession MR pulse sequence. The total acquisition time was 21.5s/phase with a voxel size of 3×3×5 mm 3 and an image matrix of 128×128×56. Image similarity was evaluated with difference maps between the reference and reconstructed images. The VDK, conventional keyhole, and zero filling methods were compared for this simulation study. Results: Using 80% of the ky data and 70% of the kz data from the library resulted in 12.20% average intensity difference from the reference, and 21.60% and 28.45% difference in threshold pixel difference for conventional keyhole and zero filling, respectively. The imaging time will be reduced from 21.5s to 1.3s per volume using the VDK method. Conclusion: Near real-time 4D MR imaging can be achieved using the volumetric dynamic keyhole method. That makes the possibility of utilizing 4D MRI during MR-guided radiotherapy.

The lateral infratrigeminal transpontine window to deep pontine lesions.

Science.gov (United States)

Ferroli, Paolo; Schiariti, Marco; Cordella, Roberto; Boffano, Carlo; Nava, Simone; La Corte, Emanuele; Cavallo, Claudio; Bauer, Dario; Castiglione, Melina; Broggi, Morgan; Acerbi, Francesco; Broggi, Giovanni

2015-09-01

Surgery of brainstem lesions is increasingly performed despite the fact that surgical indications and techniques continue to be debated. The deep pons, in particular, continues to be a critical area in which the specific risks related to different surgical strategies continue to be examined. With the intention of bringing new knowledge into this important arena, the authors systematically examined the results of brainstem surgeries that have been performed through the lateral infratrigeminal transpontine window. Between 1990 and 2013, 29 consecutive patients underwent surgery through this window for either biopsy sampling or for removal of a deep pontine lesion. All of this work was performed at the Department of Neurosurgery of the Istituto Nazionale Neurologico "Carlo Besta", in Milan, Italy. A retrospective analysis of the findings was conducted with the intention of bringing further clarity to this important surgical strategy. The lateral infratrigeminal transpontine window was exposed through 4 different approaches: 1) classic retrosigmoid (15 cases), 2) minimally invasive keyhole retrosigmoid (10 cases), 3) translabyrinthine (1 case), and 4) combined petrosal (3 cases). No deaths occurred during the entire clinical study. The surgical complications that were observed included hydrocephalus (2 cases) and CSF leakage (1 case). In 6 (20.7%) of 29 patients the authors encountered new neurological deficits during the immediate postoperative period. All 6 of these patients had undergone lesion removal. In only 2 of these 6 patients were permanent sequelae observed at 3 months follow-up. These findings show that 93% of the patients studied did not report any permanent worsening of their neurological condition after this surgical intervention. This retrospective study supports the idea that the lateral infratrigeminal transpontine window is both a low-risk and safe corridor for either biopsy sampling or for removal of deep pontine lesions.

Dose-response effects in immunizations with keyhole limpet haemocyanin and rabies vaccine: shift in some immunodeficiency states

NARCIS (Netherlands)

Korver, K.; Boeschoten, E. W.; Krediet, R. T.; van Steenis, G.; Schellekens, P. T.

1987-01-01

We investigated the primary antibody response to the antigens keyhole limpet haemocyanin (KLH) and rabies vaccine (RV). Eighty-one healthy volunteers were injected with nine doses of KLH (ranging from 10 to 2500 micrograms) and 66 volunteers with six doses of RV (ranging from 17 to 680 micrograms

Supraorbital Keyhole Microsurgical Fenestration of Symptomatic Temporal Arachnoid Cysts in Children: Advantages and Limitations.

Science.gov (United States)

Elkheshin, Sherif; Soliman, Ahmed

2017-01-01

To investigate the impact of endoscope-assisted microsurgical fenestration on temporal arachnoid cysts, and to determine the advantages and limitations of the technique. Twenty-five children with symptomatic temporal arachnoid cysts were operated via eyebrow supraorbital keyhole microsurgical fenestration targeting the medial cyst wall. Preoperative magnetic resonance imaging (MRI) of the brain was done for all patients. Preoperative clinical presentation of the patients included headache (80%), nausea & vomiting (64%), drug resistant epilepsy (52%), macrocephaly (12%) papilledema (28%), motor weakness in the form of right-sided hemiparesis (12%) and cranial nerve palsy. Postoperative complete subsidence of headache was noted in 50%, while 20% remained unchanged. Drug resistant epilepsy improved in 69% of the patients. Postoperative MRI showed initial decrease in cyst volume as early as 3 months, only in a range of 5-12% volume reduction, and the late follow-up done at 6 and 18 months continued to show further reduction reported to be significant (p CSF) collection was the most common complication (20%). Only 1 patient experienced CSF leak mandating cysto-peritoneal shunting. Conclusıon: Eyebrow supraorbital keyhole microsurgical fenestration for temporal arachnoid cysts can be performed with a fairly low risk of complications and yields a favorable improvement in clinical and neuroimaging outcomes.

The far lateral transpontomedullary sulcus approach to pontine cavernous malformations: technical report and surgical results.

Science.gov (United States)

Abla, Adib A; Benet, Arnau; Lawton, Michael T

2014-09-01

Pontine cavernous malformations (CMs) located on a peripheral pontine surface or the fourth ventricular floor are resectable lesions, but those deep within the pons away from a pial surface are typically observed. However, the anterior bulge of the pons formed by the brachium pontis creates a unique entry point for access to deep pontine lesions from below, working upward through the pontomedullary sulcus. We developed a transpontomedullary sulcus (TPMS) approach to these lesions. The TPMS approach used the far lateral craniotomy and upper vagoaccessory triangle to define the surgical corridor. The entry point was above the olive, lateral to the pyramidal tracts and cranial nerve (CN) VI, above the preolivary sulcus and CN XII, and medial to CNs VII and VIII and CNs IX through XI. Four patients underwent this approach. All presented with hemorrhage and CN VI palsies. All pontine CMs were resected completely. Three patients were improved or unchanged, with good outcomes (modified Rankin Scale score ≤2) in all patients. The central pons remains difficult territory to access, and new surgical corridors are needed. The bulging underbelly of the pons allows access to pontine lesions deep to the pial surface from below. The far lateral TPMS approach is a novel and more direct alternative to the retrosigmoid transmiddle cerebellar peduncle approach. Unlike the retrosigmoid approach, the TPMS approach requires minimal parenchymal transgression and uses a brainstem entry point medial to most lower CNs. Favorable results demonstrate the feasibility of resecting pontine CMs that might have been previously deemed unresectable.

Supra-orbital keyhole removal of anterior fossa and parasellar meningiomas Minicraniotomia supra-orbitária superciliar no tratamento de meningiomas na fossa craniana anterior e para-selares

Directory of Open Access Journals (Sweden)

Manoel Antonio de Paiva-Neto

2010-06-01

Full Text Available The improvement of surgical techniques as well as the introduction of new surgical instruments promoted the use of keyhole craniotomies in neurosurgery. We evaluated the technical aspects of the supra-orbital keyhole approach considering the indications, limitations, and complications of this approach to treat anterior cranial fossa and parasellar meningiomas. Twenty-four patients (21 females; mean age, 53±8.6 years operated on between 2002 and 2006 through a supra-orbital eyebrow approach were studied. Maximal tumor diameter ranged from 1.6 to 6 cm. Gross total resection was done in 20 (83.3%. All tumors were histologically benign. Two patients (8% experienced CSF rinorhea and another two patients suffered transitory diabetes insipidus (8%. One patient experienced transitory hemiparesis. There was one case of meningitis and one mortality. Follow-up ranged between 6 to 66 months (mean 31.5±20.1 months, with no recurrence. The supra-orbital keyhole craniotomy is a useful minimally invasive approach to treat selected anterior fossa and parasellar meningiomas.A evolução técnica e a introdução de instrumentais cirúrgicos mais delicados proporcionaram o uso de craniotomias menores no tratamento de patologias intracranianas. Avaliamos os aspectos técnicos da minicraniotomia supra-orbitária superciliar, considerando as indicações, limitações e complicações no tratamento de meningiomas na fossa craniana anterior e para-selares. Vinte e quarto pacientes (21 mulheres; idade média, 53±8,6 anos operados entre 2002 e 2006 foram estudados. O diâmetro tumoral máximo variou de 1,6 a 6 cm. Ressecção total foi obtida em 20 (83,3%. Todos os tumores eram histologicamente benignos. Dois pacientes (8% apresentaram fistula liquórica pós-operatória e outros dois diabetes insipido transitórioa (8%. Um paciente evoluiu com hemiparesia transitória. Houve um caso de meningite e um de evolução fatal. O seguimento variou de 6 a 66 meses (m

Effective capacity of multiple antenna channels: Correlation and keyhole

KAUST Repository

Zhong, Caijun

2012-01-01

In this study, the authors derive the effective capacity limits for multiple antenna channels which quantify the maximum achievable rate with consideration of link-layer delay-bound violation probability. Both correlated multiple-input single-output and multiple-input multiple-output keyhole channels are studied. Based on the closed-form exact expressions for the effective capacity of both channels, the authors look into the asymptotic high and low signal-to-noise ratio regimes, and derive simple expressions to gain more insights. The impact of spatial correlation on effective capacity is also characterised with the aid of a majorisation theory result. It is revealed that antenna correlation reduces the effective capacity of the channels and a stringent quality-of-service requirement causes a severe reduction in the effective capacity but can be alleviated by increasing the number of antennas. © 2012 The Institution of Engineering and Technology.

Assessment of invasiveness of the Orange Keyhole Sponge, Mycale Armata, in Kaneohe Bay Oahu, Hawaii, based on surveys 2004-2005 (NODC Accession 0002602)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Orange Keyhole Sponge, Mycale armata Thiele, was unknown in Hawaii prior to 1996. First reported in Pearl Harbor, it now occurs in virtually every commercial...

Assessment of Invasiveness of the Orange Keyhole Sponge Mycale Armata in Kaneohe Bay, Oahu, Hawaii Based on Surveys 2004-2005 (NODC Accession 0002602)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Orange Keyhole Sponge, Mycale armata Thiele, was unknown in Hawaii prior to 1996. First reported in Pearl Harbor, it now occurs in virtually every commercial...

Accurate multi-robot targeting for keyhole neurosurgery based on external sensor monitoring.

Science.gov (United States)

Comparetti, Mirko Daniele; Vaccarella, Alberto; Dyagilev, Ilya; Shoham, Moshe; Ferrigno, Giancarlo; De Momi, Elena

2012-05-01

Robotics has recently been introduced in surgery to improve intervention accuracy, to reduce invasiveness and to allow new surgical procedures. In this framework, the ROBOCAST system is an optically surveyed multi-robot chain aimed at enhancing the accuracy of surgical probe insertion during keyhole neurosurgery procedures. The system encompasses three robots, connected as a multiple kinematic chain (serial and parallel), totalling 13 degrees of freedom, and it is used to automatically align the probe onto a desired planned trajectory. The probe is then inserted in the brain, towards the planned target, by means of a haptic interface. This paper presents a new iterative targeting approach to be used in surgical robotic navigation, where the multi-robot chain is used to align the surgical probe to the planned pose, and an external sensor is used to decrease the alignment errors. The iterative targeting was tested in an operating room environment using a skull phantom, and the targets were selected on magnetic resonance images. The proposed targeting procedure allows about 0.3 mm to be obtained as the residual median Euclidean distance between the planned and the desired targets, thus satisfying the surgical accuracy requirements (1 mm), due to the resolution of the diffused medical images. The performances proved to be independent of the robot optical sensor calibration accuracy.

HUMORAL IMMUNE-RESPONSE TO 2,4-DINITROPHENYL KEYHOLE LIMPET HEMOCYANIN IN ANTIGEN-FREE, GERM-FREE AND CONVENTIONAL BALB/C MICE

NARCIS (Netherlands)

BOS, NA; PLOPLIS, VA

The B cell immune response to 2,4-dinitrophenyl (DNP) keyhole limpet hemocyanin was compared in antigen-free, germ-free and conventional BALB/c mice. The numbers of total and of DNP-specific IgM-, IgG- and IgA-secreting cells in the spleen were determined by enzyme-linked immunosorbent plaque assays

An optimization method for defects reduction in fiber laser keyhole welding

Science.gov (United States)

Ai, Yuewei; Jiang, Ping; Shao, Xinyu; Wang, Chunming; Li, Peigen; Mi, Gaoyang; Liu, Yang; Liu, Wei

2016-01-01

Laser welding has been widely used in automotive, power, chemical, nuclear and aerospace industries. The quality of welded joints is closely related to the existing defects which are primarily determined by the welding process parameters. This paper proposes a defects optimization method that takes the formation mechanism of welding defects and weld geometric features into consideration. The analysis of welding defects formation mechanism aims to investigate the relationship between welding defects and process parameters, and weld features are considered to identify the optimal process parameters for the desired welded joints with minimum defects. The improved back-propagation neural network possessing good modeling for nonlinear problems is adopted to establish the mathematical model and the obtained model is solved by genetic algorithm. The proposed method is validated by macroweld profile, microstructure and microhardness in the confirmation tests. The results show that the proposed method is effective at reducing welding defects and obtaining high-quality joints for fiber laser keyhole welding in practical production.

Estudo da Técnica Tig Keyhole por Meio do Análise Comparativo entre Duas Tochas de Alta Produtividade na União de Chapas de Aço Carbono de Meia Espessura

Directory of Open Access Journals (Sweden)

Erick Alejandro González Olivares

2015-09-01

Full Text Available Resumo Na bibliografia de referência comum, a soldagem por meio da técnica Keyhole sempre foi associada a processos de soldagem com uma alta concentração de energia, como o processo Laser ou o processo Plasma. Novos avanços em tochas TIG estão mudando a forma em como o processo de soldagem TIG deveria ser considerado. Um exemplo desses novos avanços é a tocha comercialmente conhecida como Infocus, que segundo seus fabricantes a principal característica da tocha é a capacidade de concentração de energia na ponta do eletrodo, por médio de um aumento na potência de refrigeração do eletrodo, diferenciando à Infocus de uma tocha convencional TIG. Tal concentração de energia permite à tocha Infocus trabalhar com a técnica Keyhole. Portanto, é objetivo do presente trabalho estudar a factibilidade de uma tocha convencional TIG de usar a técnica Keyhole, com as mesmas condições de trabalho que a tocha comercialmente conhecida como Infocus. Através dos ensaios realizados foi possível confirmar que o processo TIG consegue trabalhar com a técnica Keyhole, sem necessidade de uma tocha com características especiais. Porém, o eletrodo da tocha Infocus possui uma vida maior, em comparação a um eletrodo convencional da mesma composição, aumentando a produtividade do processo.

Posterior fossa meningioma (surgical experiences) | Moussa ...

African Journals Online (AJOL)

Symptoms included headache (75%), cerebellar manifestations (60%), cranial nerve affection (40%) and hearing disturbances (15%). Most of the cases (50%) were cerebellopontine angle meningioma while the least (5%) were foramen magnum meningioma. Surgical approaches used included retrosigmoid approach ...

MEASUREMENT OF AFFINITY IN SERUM SAMPLES OF ANTIGEN-FREE, GERM-FREE AND CONVENTIONAL MICE AFTER HYPERIMMUNIZATION WITH 2,4-DINITROPHENYL KEYHOLE LIMPET HEMOCYANIN, USING SURFACE-PLASMON RESONANCE

NARCIS (Netherlands)

BAKKER, R; LASONDER, E; BOS, NA

We previously investigated the primary and secondary responses and hyperimmunization to the T cell-dependent antigen 2,4-dinitrophenyl keyhole limpet hemocyanin (DNP-KLH) in antigen-free (AF), germ-free (GF) and conventional (CV) mice. Both the absolute and relative numbers of DNP-specific

Three finger palpation technique of vas deferens for keyhole vasectomy in spotted (Axis axis and sambar deer (Cervus unicolor

Directory of Open Access Journals (Sweden)

B. J. William

2014-09-01

Full Text Available Aim: Vasectomy is performed in deer for population control, maintain pedigreed animals and prevent inbreeding. Conventional procedure of vasectomy required a long-term anesthesia and longer duration of hospitalization, which often result in stress, morbidity and mortality. A study was conducted to capture, neuter and release the deer with minimal hospitalization and stress by adopting three finger palpation technique of vas deferens and performing vasectomy through a key-hole incision. Materials and Methods: The study was conducted on three spotted male deer and three sambar male deer, which were immobilized with a mixture of xylazine at the dose of 1.00 mg/kg and ketamine at the dose of 5.00 mg/kg. The vas deferens could be palpated as a piece of cooked spaghetti at the neck of the scrotum on the anterior aspect by three finger palpation technique and was able to fix the vas deferens between the thumb and middle finger. Through a key-hole incision of <5 mm length, the vas deferens was exteriorized and resected using electrocautery and the skin incision was sealed with methyl methacrylate. The deer were released on the same day, and no post-operative complication was noticed. Conclusion: The study revealed that three finger palpation technique of vas deferens provided guidance for easy access to vas deferens for vasectomy in deer with less hospitalization, and the deer could be released on the same day.

Interaction of Chelerythrine with Keyhole Limpet Hemocyanin: a Fluorescence Spectroscopy and Molecular Docking Study

Science.gov (United States)

Zhong, M.; Long, R. Q.; Wang, Y. H.; Chen, C. L.

2018-05-01

The quenching mechanism between chelerythrine (CHE) and keyhole limpet hemocyanin (KLH) was investigated using fluorescence spectroscopy and molecular docking. The experiments were conducted at three different temperatures (293, 298, and 303 K). The results revealed that the intrinsic fluorescence of KLH was strongly quenched by CHE through a static quenching mechanism. The thermodynamic parameters (ΔG, ΔH, and ΔS) of the interaction were calculated, indicating that the interaction between CHE and KLH was spontaneous and that van der Waals forces and hydrogen bond formation played major roles in the binding process. The intrinsic fluorescence of the tyrosine and tryptophan residues in KLH was studied by synchronous fluorescence, which suggested that CHE changed the conformation of KLH. Finally, molecular docking was used to obtain detailed information on the binding sites and binding affinities between CHE and KLH.

Assessment of Invasiveness of the Orange Keyhole Sponge Mycale Armata in Kaneohe Bay, Oahu, Hawaii Based on Surveys 2005-2006, Year 2 of Hawaii Coral Reef Initiative (NODC Accession 0033380)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Orange Keyhole Sponge, Mycale armata Thiele, was unknown in Hawaii prior to 1996. It was first reported in Pearl Harbor and has been reported in low abundance...

The Cosmic Keyhole How Astronomy Is Unlocking the Secrets of the Universe

CERN Document Server

Gater, William J.H

2009-01-01

It is 400 years since Galileo first turned the newly invented telescope towards the heavens and saw things that few had ever seen before. His discoveries, along with those of his contemporaries, completely changed our view of the world. Since that time, there have been many revolutions in our understanding of the universe, some perhaps even more revolutionary than the ones from Galileo’s time. In this book, Will Gater leads us through various recent advances in modern astronomy that have increased our understanding of the universe and seen it grow from a single Solar System full of intriguing worlds to a galaxy filled with other star systems and their own planets — maybe even Earthlike worlds. This is a journey like no other. What you glimpse through Gater’s keyhole is vast, breathtakingly beautiful, and sometimes utterly bizarre, certainly unfamiliar to those of us on Terra Firma. From the desolate plains of Mars and the frozen moons of the outer Solar System, from the Milky Way to the ends of the univ...

Melt pool and keyhole behaviour analysis for deep penetration laser welding

International Nuclear Information System (INIS)

Fabbro, R

2010-01-01

One usually defines the main characteristic of the welding performances of a given laser system by its 'penetration curve' that corresponds to the welding depth as a function of the welding speed V w for a given set of operating parameters. Analysis of a penetration curve is interesting and gives very fruitful results. Coupled with high-speed video imaging of melt pool surface and ejected plume behaviour, the analysis of this penetration curve on a very large range of welding speeds, typically from 0 to 50 m min -1 , has allowed us to observe very different and characteristic regimes. These regimes are mainly characterized by the physical processes by which they impede the laser beam penetration inside the material. We show that it is only at rather high welding speeds that these limiting processes are reduced. Consequently, the scaling law of welding depth with welding speed is in agreement with adapted modelling of this process. On the other hand, as the welding speed is reduced, different effects depending on the weld pool dynamics and plume interaction strongly disturb the keyhole stability and are responsible for the deviation of the penetration curve from the previous modelling that agrees with a 1/V w scaling law. A corresponding criterion for the occurrence of this effect is defined.

Guided asteroid deflection by kinetic impact: Mapping keyholes to an asteroid's surface

Science.gov (United States)

Chesley, S.; Farnocchia, D.

2014-07-01

range from around 1 for a porous, compressible body producing negligible ejecta, to 2 when the ejecta momentum matches the spacecraft momentum, and as high as 5--10 for rocky bodies that produce large, high-velocity ejecta fragments. If the impactor hits the centerpoint of a spherical asteroid the momentum of the escaping ejecta directly adds to the momentum of the impacting asteroid, but if the impact is oblique then the ejecta and spacecraft momenta are added to the asteroid in vector sum. This suggests the possibility that for a given intercept trajectory the asteroid deflection could include guidance by targeting an oblique impact that could steer the asteroid Δ V to a more optimal direction that is different from the relative velocity direction of the spacecraft. An oblique impact decreases the net Δ V magnitude, and yet could significantly increase the net deflection at the time of the threatening Earth encounter. We use asteroid (101955) Bennu, which is the target of the OSIRIS-REx asteroid sample return mission and which has a series of potential Earth impacts in the years from 2175--2196, as an example to demonstrate the effectiveness of the oblique impact. These future potential impacts will occur if the asteroid passes through one of a series of keyholes when the asteroid passes the Earth at roughly the lunar distance from the Earth in 2135. To study the Bennu deflection problem we simulate a hypervelocity spacecraft impact on Bennu in March 2021, after the OSIRIS-REx mission is complete. In our example, the spacecraft arrives from approximately the sunward direction, and targeting ahead or behind the center of the asteroid allows non-negligible transverse accelerations for modest values of β. A given impact location on the asteroid surface yields a given Δ V vector, and our approach starts by mapping the net Δ V components on the surface for an assumed value of β. Knowing the mapping from impact location to Δ V and also the mapping from Δ V to the

Comparison of microscopic and endoscopic view of the internal acoustic meatus: A cadaveric study.

Science.gov (United States)

Montibeller, Guilherme Ramina; Hendrix, Philipp; Fries, Fabian N; Becker, Kurt W; Oertel, Joachim

2018-04-01

The endoscope is thought to provide an improved exposure of the internal acoustic meatus after retrosigmoid craniotomy for microsurgical resection of intrameatal tumors. The aim of this study is to quantify the differences in internal acoustic meatus (IAM) exposure comparing microscopic and endoscopic visualization. A retrosigmoid approach was performed on 5 cadaver heads. A millimeter gauge was introduced into the internal acoustic meatus, and examinations with a surgical microscope and 0°, 30° and 70° rigid endoscopes were performed. The extent of IAM depth visualized with the microscope and the different angled endoscopes were analyzed. The microscopic view allowed an average IAM depth visualization of 2.8 mm. The endoscope allowed an improved exposure of IAM in all cases. The 0°, 30° and 70° endoscopes permitted an exposure that was respectively 96% (5.5 mm), 139% (6.7 mm) and 200% (8.4 mm) more lateral than the microscopic view. Angled optics, however, provided an image distortion, specifically the 70° endoscope. The endoscope provides a superior visualization of the IAM compared to the microscope when using a retrosigmoid approach. The 30° endoscope represented an ideal compromise of superior visualization with marginal image distortion. Additional implementation of the endoscope into microsurgery of intrameatal tumors likely facilitates complete tumor removal and might spare facial and vestibulocochlear function. Clin. Anat. 31:398-403, 2018. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

CT pre-operative planning of a new semi-implantable bone conduction hearing device

Energy Technology Data Exchange (ETDEWEB)

Law, Eric K.C.; Bhatia, Kunwar S.S. [Prince of Wales Hospital, The Chinese University of Hong Kong, Department of Imaging and Interventional Radiology, Hong Kong, SAR (China); Tsang, Willis S.S.; Tong, Michael C.F. [Prince of Wales Hospital, The Chinese University of Hong Kong, Department of Otorhinolaryngology, Head and Neck Surgery, Hong Kong, SAR (China); Shi, Lin [The Chinese University of Hong Kong, Department of Medicine and Therapeutics, Hong Kong, SAR (China); The Chinese University of Hong Kong, Chow Yuk Ho Technology Center for Innovative Medicine, Hong Kong, SAR (China)

2016-06-15

Accommodating a novel semi-implantable bone conduction hearing device within the temporal bone presents challenges for surgical planning. This study describes the utility of CT in pre-operative assessment of such an implant. Retrospective review of pre-operative CT, clinical and surgical records of 16 adults considered for device implantation. Radiological suitability was assessed on CT using 3D simulation software. Antero-posterior (AP) dimensions of the mastoid bone and minimum skull thickness were measured. CT planning results were correlated with operative records. Eight and five candidates were suitable for device placement in the transmastoid and retrosigmoid positions, respectively, and three were radiologically unsuitable. The mean AP diameter of the mastoid cavity was 14.6 mm for the transmastoid group and 4.6 mm for the retrosigmoid group (p < 0.05). Contracted mastoid and/or prior surgery were predisposing factors for unsuitability. Four transmastoid and five retrosigmoid positions required sigmoid sinus/dural depression and/or use of lifts due to insufficient bone capacity. A high proportion of patients being considered have contracted or operated mastoids, which reduces the feasibility of the transmastoid approach. This finding combined with the complex temporal bone geometry illustrates the importance of careful CT evaluation using 3D software for precise device simulation. (orig.)

Endoscopic extradural supraorbital approach to the temporal pole and adjacent area: technical note.

Science.gov (United States)

Komatsu, Fuminari; Imai, Masaaki; Shigematsu, Hideaki; Aoki, Rie; Oda, Shinri; Shimoda, Masami; Matsumae, Mitsunori

2017-08-25

The authors' initial experience with the endoscopic extradural supraorbital approach to the temporal pole and adjacent area is reported. Fully endoscopic surgery using the extradural space via a supraorbital keyhole was performed for tumors in or around the temporal pole, including temporal pole cavernous angioma, sphenoid ridge meningioma, and cavernous sinus pituitary adenoma, mainly using 4-mm, 0° and 30° endoscopes and single-shaft instruments. After making a supraorbital keyhole, a 4-mm, 30° endoscope was advanced into the extradural space of the anterior cranial fossa during lifting of the dura mater. Following identification of the sphenoid ridge, orbital roof, and anterior clinoid process, the bone lateral to the orbital roof was drilled off until the dura mater of the anterior aspect of the temporal lobe was exposed. The dura mater of the temporal lobe was incised and opened, exposing the temporal pole under a 4-mm, 0° endoscope. Tumors in or around the temporal pole were safely removed under a superb view through the extradural corridor. The endoscopic extradural supraorbital approach was technically feasible and safe. The anterior trajectory to the temporal pole using the extradural space under endoscopy provided excellent visibility, allowing minimally invasive surgery. Further surgical experience and development of specialized instruments would promote this approach as an alternative surgical option.

SYNTHESIS OF 25-HYDROXYVITAMIN D3 CONJUGATE WITH KEYHOLE LIMPET HEMOCYANIN AND OBTAINING OF IMMUNE SERA

Directory of Open Access Journals (Sweden)

А. O. Mazanova

2015-08-01

Full Text Available The study was aimed at obtaining polyclonal antibodies that recognize 25-Hydroxyvitamin D3, for their further specifications and applications in immunochemical test systems of 25-Hydroxyvitamin D3, determination in blood serum. We used the methods of chemical synthesis of immunoconjugates (modified carbodiimide method using N´-ethyl carbodiimide, thin layer chromatography, gel filtration and indirect immunoenzyme analysis ELISA. The work describes the stages of the synthesis of 25-Hydroxyvitamin D3, immunoconjugate with keyhole limpet hemocyanin (KLH, which was used for receiving immune sera. As a result of mouse and rabbit immunization antisera were obtained and antibody titers against 25-Hydroxyvitamin D3, were tested by immunoenzyme assay. It was demonstrated that the titer of specific antibodies was higher in rabbits compared with mice. The resulting polyclonal antibodies can be used for the development of immunochemical test systems for screening studies of 25-Hydroxyvitamin D3, content in human blood serum as a marker of vitamin D3 availability.

Haliotis tuberculata hemocyanin (HtH): analysis of oligomeric stability of HtH1 and HtH2, and comparison with keyhole limpet hemocyanin KLH1 and KLH2.

Science.gov (United States)

Harris, J R; Scheffler, D; Gebauer, W; Lehnert, R; Markl, J

2000-12-01

The multimeric/higher oligomeric states of the two isoforms of Haliotis tuberculata hemocyanin (HtH1 and HtH2) have been assessed by transmission electron microscopy (TEM) of negatively stained specimens, for comparison with previously published structural data from keyhole limpet hemocyanin (KLH1 and KLH2) [see Harris, J.R., Gebauer, W., Guderian, F.U., Markl, J., 1997a. Keyhole limpet hemocyanin (KLH), I: Reassociation from Immucothel followed by separation of KLH1 and KLH2. Micron, 28, 31-41; Harris, J.R., Gebauer, W., Söhngen, S.M., Nermut, M.V., Markl, J., 1997b. Keyhole limpet hemocyanin (KLH). II: Characteristic reassociation properties of purified KLH1 and KLH2. Micron, 28, 43-56; Harris, J.R., Gebauer, W., Adrian, M., Markl, J., 1998. Keyhole limpet hemocyanin (KLH): Slow in vitro reassociation of KLH1 and KLH2 from Immucothel. Micron, 29, 329-339]. In purified samples of both HtH isoforms, the hollow cylindrical ca 8MDa didecamer predominates together with a small number of decamers, but tri- and longer multidecamers are detectable only in the HtH2. The stability of the two HtH isoforms under varying ionic conditions have been monitored, thereby enabling conditions for the production of stable decamers to be established. The ability of these decamers to reform multimers in the presence of 10 and 100mM concentrations of calcium and magnesium ions in Tris-HCl buffer (pH 7.4), and also of individual HtH1 and HtH2 subunits (produced by pH 9.6 dissociation in glycine-NaOH buffer), to reassociate in the presence of calcium and magnesium ions, has been assessed. For the HtH1 decamers, the predominant multimeric product is the didecamer at 10 and 100mM calcium and magnesium concentrations, whereas for the HtH2 decamers, large numbers of multidecamers are produced, with the reaction proceeding more completely at the higher calcium and magnesium concentration. With the HtH1 subunit, reassociation in the presence of 10 and 100mM calcium and magnesium ions yielded

Effect of HI-6 on cytokines production after immunity stimulation by keyhole limpet hemocyanin in a mouse model.

Science.gov (United States)

Pohanka, Miroslav

2014-01-01

HI-6 or asoxime in some sources is an antidotum for nerve agents. In recent experiments, implication of HI-6 in immunity response was proved; however, the issue was not studied in details. In this experiment, role of cytokines in HI-6 impact on immunity was searched. DESIG N: BALB/c mice were exposed to saline, HI-6 in a dose 1-100 mg/kg and/or 1 keyhole limpet hemocyanin (KLH) 1 mg/kg. Mice were sacrificed 21 days after experiment beginning and interleukins (IL) 1, 2, 4, 6 were determined by Enzyme Linked Immunosorbent Assay (ELISA). The animals had no pathological manifestation. From the tested cytokines, no significant alteration was found for the IL-1, IL-4 and IL-6. IL-2 was significantly increased in a dose response manner. The experimental data well correlates with the previous work where HI-6 caused increase of antibodies production. HI-6 is suitable to be used as an adjuvant whenever immunity should be pharmacologically altered.

Reduced CSF leak in complete calvarial reconstructions of microvascular decompression craniectomies using calcium phosphate cement.

Science.gov (United States)

Eseonu, Chikezie I; Goodwin, C Rory; Zhou, Xin; Theodros, Debebe; Bender, Matthew T; Mathios, Dimitrios; Bettegowda, Chetan; Lim, Michael

2015-12-01

Calcium phosphate cement provides a biomaterial that can be used for calvarial reconstruction in a retrosigmoid craniectomy for microvascular decompression (MVD). This study evaluates the outcomes of postoperative CSF leak and wound infection for patients undergoing a complete cranioplasty using calcium phosphate cement versus incomplete cranioplasty using polyethylene titanium mesh following a retrosigmoid craniectomy for MVD. The authors evaluated 211 cases involving patients who underwent first-time retrosigmoid craniectomies performed by a single attending surgeon fortrigeminal neuralgia from October 2008 to June 2014. From this patient population, 111 patients underwent calvarial reconstruction after retrosigmoid craniectomy using polyethylene titanium mesh, and 100 patients had reconstructions using calcium phosphate cement. A Pearson's chi-square test was used to compare postoperative complications of CSF leak and wound infection in these 2 types of cranioplasties. The polyethylene titanium mesh group included 5 patients (4.5%) with postoperative CSF leak or pseudomeningocele and 3 patients (2.7%) with wound infections. In the calcium phosphate cement group, no patients had a CSF leak, and 2 patients (2%) had wound infections. This represented a statistically significant reduction of postoperative CSF leak in patients who underwent calcium phosphate reconstructions of their calvarial defect compared with those who underwent polyethylene titanium mesh reconstructions (p = 0.03). No significant difference was seen between the 2 groups in the number of patients with postoperative wound infections. Calcium phosphate cement provides a viable alternative biomaterial for calvarial reconstruction of retrosigmoid craniectomy defects in patients who have an MVD. The application of this material provides a biocompatible barrier that reduces the incidence of postoperative CSF leaks.

Straight trajectory planning for keyhole neurosurgery in sheep with automatic brain structures segmentation

Science.gov (United States)

Favaro, Alberto; Lad, Akash; Formenti, Davide; Zani, Davide Danilo; De Momi, Elena

2017-03-01

In a translational neuroscience/neurosurgery perspective, sheep are considered good candidates to study because of the similarity between their brain and the human one. Automatic planning systems for safe keyhole neurosurgery maximize the probe/catheter distance from vessels and risky structures. This work consists in the development of a trajectories planner for straight catheters placement intended to be used for investigating the drug diffusivity mechanisms in sheep brain. Automatic brain segmentation of gray matter, white matter and cerebrospinal fluid is achieved using an online available sheep atlas. Ventricles, midbrain and cerebellum segmentation have been also carried out. The veterinary surgeon is asked to select a target point within the white matter to be reached by the probe and to define an entry area on the brain cortex. To mitigate the risk of hemorrhage during the insertion process, which can prevent the success of the insertion procedure, the trajectory planner performs a curvature analysis of the brain cortex and wipes out from the poll of possible entry points the sulci, as part of brain cortex where superficial blood vessels are naturally located. A limited set of trajectories is then computed and presented to the surgeon, satisfying an optimality criteria based on a cost function which considers the distance from critical brain areas and the whole trajectory length. The planner proved to be effective in defining rectilinear trajectories accounting for the safety constraints determined by the brain morphology. It also demonstrated a short computational time and good capability in segmenting gyri and sulci surfaces.

The intracranial facial nerve as seen through different surgical windows: an extensive anatomosurgical study.

Science.gov (United States)

Bernardo, Antonio; Evins, Alexander I; Visca, Anna; Stieg, Phillip E

2013-06-01

The facial nerve has a short intracranial course but crosses critical and frequently accessed surgical structures during cranial base surgery. When performing approaches to complex intracranial regions, it is essential to understand the nerve's conventional and topographic anatomy from different surgical perspectives as well as its relationship with surrounding structures. To describe the entire intracranial course of the facial nerve as observed via different neurosurgical approaches and to provide an analytical evaluation of the degree of nerve exposure achieved with each approach. Anterior petrosectomies (middle fossa, extended middle fossa), posterior petrosectomies (translabyrinthine, retrolabyrinthine, transcochlear), a retrosigmoid, a far lateral, and anterior transfacial (extended maxillectomy, mandibular swing) approaches were performed on 10 adult cadaveric heads (20 sides). The degree of facial nerve exposure achieved per segment for each approach was assessed and graded independently by 3 surgeons. The anterior petrosal approaches offered good visualization of the nerve in the cerebellopontine angle and intracanalicular portion superiorly, whereas the posterior petrosectomies provided more direct visualization without the need for cerebellar retraction. The far lateral approach exposed part of the posterior and the entire inferior quadrants, whereas the retrosigmoid approach exposed parts of the superior and inferior quadrants and the entire posterior quadrant. Anterior and anteroinferior exposure of the facial nerve was achieved via the transfacial approaches. The surgical route used must rely on the size, nature, and general location of the lesion, as well as on the capability of the particular approach to better expose the appropriate segment of the facial nerve.

Robotic and artificial intelligence for keyhole neurosurgery: the ROBOCAST project, a multi-modal autonomous path planner.

Science.gov (United States)

De Momi, E; Ferrigno, G

2010-01-01

The robot and sensors integration for computer-assisted surgery and therapy (ROBOCAST) project (FP7-ICT-2007-215190) is co-funded by the European Union within the Seventh Framework Programme in the field of information and communication technologies. The ROBOCAST project focuses on robot- and artificial-intelligence-assisted keyhole neurosurgery (tumour biopsy and local drug delivery along straight or turning paths). The goal of this project is to assist surgeons with a robotic system controlled by an intelligent high-level controller (HLC) able to gather and integrate information from the surgeon, from diagnostic images, and from an array of on-field sensors. The HLC integrates pre-operative and intra-operative diagnostics data and measurements, intelligence augmentation, multiple-robot dexterity, and multiple sensory inputs in a closed-loop cooperating scheme including a smart interface for improved haptic immersion and integration. This paper, after the overall architecture description, focuses on the intelligent trajectory planner based on risk estimation and human criticism. The current status of development is reported, and first tests on the planner are shown by using a real image stack and risk descriptor phantom. The advantages of using a fuzzy risk description are given by the possibility of upgrading the knowledge on-field without the intervention of a knowledge engineer.

Study of CW Nd-Yag laser welding of Zn-coated steel sheets

International Nuclear Information System (INIS)

Fabbro, Remy; Coste, Frederic; Goebels, Dominique; Kielwasser, Mathieu

2006-01-01

The welding of Zn-coated steel thin sheets is a great challenge for the automotive industry. Previous studies have defined the main physical processes involved. For non-controlled conditions, the zinc vapour expelled from the interface of the two sheets violently expands inside the keyhole and expels the melt pool. When using CO 2 lasers, we have previously shown that an elongated laser spot produces an elongated keyhole, which is efficient for suppressing this effect. We have adopted a similar approach for CW Nd : Yag laser welding and we observe that an elongated spot is not necessary for achieving good weld seams. Several diagnostics were used in order to understand these interesting results. High-speed video camera visualizations of the top and the bottom of the keyhole during the process show the dynamics of the keyhole hydrodynamic behaviour. It appears that the role of the reflected beam on the front keyhole wall for generating a characteristic rear wall deformation is crucial for an efficient stabilization of the process. Our dynamic keyhole modelling, which includes ray tracing, totally confirms this interpretation and explains the results for very different experimental conditions (effect of welding speed, laser intensity, variable sheet thickness, laser beam intensity distribution) that will be presented

Pilot study of a heptavalent vaccine-keyhole limpet hemocyanin conjugate plus QS21 in patients with epithelial ovarian, fallopian tube, or peritoneal cancer

DEFF Research Database (Denmark)

Sabbatini, Paul J; Ragupathi, Govind; Hood, Chandra

2007-01-01

PURPOSE: To characterize the safety and immunogenicity of a heptavalent antigen-keyhole limpet hemocyanin (KLH) plus QS21 vaccine construct in patients with epithelial ovarian, fallopian tube, or peritoneal cancer in second or greater complete clinical remission. EXPERIMENTAL DESIGN: Eleven......). RESULTS: Eleven patients were included in the safety analysis; 9 of 11 patients remained on study for at least 2 weeks past fourth vaccination and were included in the immunologic analysis (two withdrew, disease progression). The vaccine was well tolerated. Self-limited and mild fatigue (maximum grade 2...... patients in this pilot trial received a heptavalent vaccine s.c. containing GM2 (10 microg), Globo-H (10 microg), Lewis Y (10 microg), Tn(c) (3 microg), STn(c) (3 microg), TF(c) (3 microg), and Tn-MUC1 (3 microg) individually conjugated to KLH and mixed with adjuvant QS21(100 microg). Vaccinations were...

Oral antibiotics enhance antibody responses to keyhole limpet hemocyanin in orally but not muscularly immunized chickens.

Science.gov (United States)

Murai, Atsushi; Kitahara, Kazuki; Okumura, Shouta; Kobayashi, Misato; Horio, Fumihiko

2016-02-01

Recent studies have emphasized the crucial role of gut microbiota in triggering and modulating immune response. We aimed to determine whether the modification of gut microbiota by oral co-administration of two antibiotics, ampicillin and neomycin, would lead to changes in the antibody response to antigens in chickens. Neonatal chickens were given or not given ampicillin and neomycin (0.25 and 0.5 g/L, respectively) in drinking water. At 2 weeks of age, the chicks were muscularly or orally immunized with antigenic keyhole limpet hemocyanin (KLH), and then serum anti-KLH antibody levels were examined by ELISA. In orally immunized chicks, oral antibiotics treatment enhanced antibody responses (IgM, IgA, IgY) by 2-3-fold compared with the antibiotics-free control, while the antibiotics did not enhance antibody responses in the muscularly immunized chicks. Concomitant with their enhancement of antibody responses, the oral antibiotics also lowered the Lactobacillus species in feces. Low doses of antibiotics (10-fold and 100-fold lower than the initial trial), which failed to change the fecal Lactobacillus population, did not modify any antibody responses when chicks were orally immunized with KLH. In conclusion, oral antibiotics treatment enhanced the antibody response to orally exposed antigens in chickens. This enhancement of antibody response was associated with a modification of the fecal Lactobacillus content, suggesting a possible link between gut microbiota and antibody response in chickens. © 2015 Japanese Society of Animal Science.

Estudo da Técnica Tig Keyhole por Meio do Análise Comparativo entre Duas Tochas de Alta Produtividade na União de Chapas de Aço Carbono de Meia Espessura

OpenAIRE

Olivares, Erick Alejandro González; Silva, Régis Henrique Gonçalves e; Dutra, Jair Carlos

2015-01-01

Resumo Na bibliografia de referência comum, a soldagem por meio da técnica Keyhole sempre foi associada a processos de soldagem com uma alta concentração de energia, como o processo Laser ou o processo Plasma. Novos avanços em tochas TIG estão mudando a forma em como o processo de soldagem TIG deveria ser considerado. Um exemplo desses novos avanços é a tocha comercialmente conhecida como Infocus, que segundo seus fabricantes a principal característica da tocha é a capacidade de concentração ...

Differential precocious sexual development of Proctoeces lintoni (Digenea: Fellodistomidae) in three sympatric species of keyhole limpets Fissurella spp. may affect transmission to the final host.

Science.gov (United States)

Balboa, L; George-Nascimento, M; Ojeda, F P

2001-10-01

The prevalence, abundance, and developmental status of the digenetic trematode Proctoeces lintoni Siddiqui et Cable 1960 were compared in 3 species of keyhole limpets Fissurella. A total of 197 limpets was collected at Caleta Chome, south-central Chile. Fissurella picta and F. costata had the highest prevalence of infection, whereas F. picta showed the greatest abundance of parasites, which increased with host shell length. However, the frequency of P. lintoni specimens with eggs in the uterus was greatest in F. costata. These results suggest that an increased rate of development of a parasite in the intermediate host may shorten the residence time necessary for maturation in the final host. Thus, faster development of the parasite in F. costata suggests the possibility that the parasites transmitted through this host species have shorter maturation times in clingfishes than individuals transmitted via other limpet species.

Retrolabyrinthine approach for cochlear nerve preservation in neurofibromatosis type 2 and simultaneous cochlear implantation

Directory of Open Access Journals (Sweden)

Bento, Ricardo Ferreira

2014-01-01

Full Text Available Introduction: Few cases of cochlear implantation (CI in neurofibromatosis type 2 (NF2 patients had been reported in the literature. The approaches described were translabyrinthine, retrosigmoid or middle cranial fossa. Objectives: To describe a case of a NF2- deafened-patient who underwent to vestibular schwannoma resection via RLA with cochlear nerve preservation and CI through the round window, at the same surgical time. Resumed Report: A 36-year-old woman with severe bilateral hearing loss due to NF2 was submitted to vestibular schwannoma resection and simultaneous CI. Functional assessment of cochlear nerve was performed by electrical promontory stimulation. Complete tumor removal was accomplishment via RLA with anatomic and functional cochlear and facial nerve preservation. Cochlear electrode array was partially inserted via round window. Sound field hearing threshold improvement was achieved. Mean tonal threshold was 46.2 dB HL. The patient could only detect environmental sounds and human voice but cannot discriminate vowels, words nor do sentences at 2 years of follow-up. Conclusion: Cochlear implantation is a feasible auditory restoration option in NF2 when cochlear anatomic and functional nerve preservation is achieved. The RLA is adequate for this purpose and features as an option for hearing preservation in NF2 patients.

Numerical simulation of spatter formation during fiber laser welding of 5083 aluminum alloy at full penetration condition

Science.gov (United States)

Wu, Dongsheng; Hua, Xueming; Huang, Lijin; Zhao, Jiang

2018-03-01

The droplet escape condition in laser welding is established in this paper. A three-dimensional numerical model is developed to study the weld pool convection and spatter formation at full penetration during the fiber laser welding of 5083 aluminum alloy. It is found that when laser power is 9 kW, the bottom of the keyhole is dynamically opened and closed. When the bottom of the keyhole is closed, the molten metal at the bottom of the back keyhole wall flows upwards along the fusion line. When the bottom of the keyhole is opened, few spatters can be seen around the keyhole at the top surface, two flow patterns exists in the rear part of the keyhole: a portion of molten metal flows upwards along the fusion line, other portion of molten metal flows to the bottom of the keyhole, which promote the spatter formation at the bottom of the keyhole rear wall.

Experimental and numerical study of spatter formation and composition change in fiber laser welding of aluminum alloy

Science.gov (United States)

Wu, Dongsheng; Hua, Xueming; Ye, Youxiong; Huang, Lijin; Li, Fang; Huang, Ye

2018-05-01

A laser welding experiment with glass is conducted to directly observe the keyhole behavior and spatter formation in fiber laser welding of aluminum alloy. A 3D model is developed to investigate the spatter formation and composition change. An additional conservation equation is introduced to describe the Mg element distribution, and the Mg element loss due to evaporation is also considered. Based on numerical and experimental results, it is found that the keyhole geometry in laser welding of aluminum alloy is different from that in laser welding of steel. There are three required steps for spatter formation around the keyhole. The high momentum of the molten metal, the high recoil pressure and vapor shear stress, and the low surface tension around the keyhole contribute to the easy formation of spatter. The in-homogeneous distribution of Mg element in the weld can be attributable to the continuous evaporation of Mg element at the top surface of keyhole rear, the upward flow of low Mg element region from the bottom of the keyhole to the top surface of keyhole rear along the fusion line, the collapse of the keyhole, and the ejection of spatters.

Technological Advances in Joining

Science.gov (United States)

1981-08-01

joint with the progressively advancing laser beam. Surface tension forces support the molten metal and close the keyhole behind the moving be:zm. Deep... keyhole welds in much the same manner as the electron beam which it so closely resembles. Low-power lasers rated at 1000 watts or less are used for...welding, the arc penetrates through the base metal to form the keyhole . Surface tension forces close the keyhole behind the arc as it progresses along

[Treatment of giant acoustic neuromas].

Science.gov (United States)

Samprón, Nicolás; Altuna, Xabier; Armendáriz, Mikel; Urculo, Enrique

2014-01-01

To analyze the treatment modality and outcome of a series of patients with giant acoustic neuromas, a particular type of tumour characterised by their size (extracanalicular diameter of 4cm or more) and high morbidity and mortality. This was a retrospective unicentre study of patients with acoustic neuromas treated in a period of 12 years. In our institutional series of 108 acoustic neuromas operated on during that period, we found 13 (12%) cases of giant acoustic neuromas. We reviewed the available data of these cases, including presentation and several clinical, anatomical, and microsurgical aspects. All patients were operated on by the same neurosurgeon and senior author (EU) using the suboccipital retrosigmoid approach and complete microsurgical removal was achieved in 10 cases. In one case, near total removal was deliberately performed, in another case a CSF shunt was placed as the sole treatment measure, and in the remaining case no direct treatment was given. One patient died in the immediate postoperative period. One year after surgery, 4 patients showed facial nerve function of iii or more in the House-Brackman scale. The 4 most important prognostic characteristics of giant acoustic neuromas are size, adhesion to surrounding structures, consistency and vascularity. Only the first of these is evident in neuroimaging. Giant acoustic neuromas are characterised by high morbidity at presentation as well as after treatment. Nevertheless, the objective of complete microsurgical removal with preservation of cranial nerve function is attainable in some cases through the suboccipital retrosigmoid approach. Copyright © 2014 Sociedad Española de Neurocirugía. Published by Elsevier España. All rights reserved.

Prediction of residual stresses and distortions due to laser beam welding of butt joints in pressure vessels

International Nuclear Information System (INIS)

Moraitis, G.A.; Labeas, G.N.

2009-01-01

A two-level three-dimensional Finite Element (FE) model has been developed to predict keyhole formation and thermo-mechanical response during Laser Beam Welding (LBW) of steel and aluminium pressure vessel or pipe butt-joints. A very detailed and localized (level-1) non-linear three-dimensional transient thermal model is initially developed, which simulates the mechanisms of keyhole formation, calculates the temperature distribution in the local weld area and predicts the keyhole size and shape. Subsequently, using a laser beam heat source model based on keyhole assumptions, a global (level-2) thermo-mechanical analysis of the LBW butt-joint is performed, from which the joint residual stresses and distortions are calculated. All the major physical phenomena associated to LBW, such as laser heat input via radiation, heat losses through convection and radiation, as well as latent heat are accounted for in the numerical model. Material properties and particularly enthalpy, which is very important due to significant material phase changes, are introduced as temperature-dependent functions. The main advantages of the developed model are its efficiency, flexibility and applicability to a wide range of LBW problems (e.g. welding for pressure vessel or pipework construction, welding of automotive, marine or aircraft components, etc). The model efficiency arises from the two-scale approach applied. Minimal or no experimental data are required for the keyhole size and shape computation by the level-1 model, while the thermo-mechanical response calculation by the level-2 model requires only process and material data. Therefore, it becomes possible to efficiently apply the developed simulation model to different material types and varying welding parameters (i.e. welding speed, heat source power, joint geometry, etc.) in order to control residual stresses and distortions within the welded structure

Numerical simulation of heat transfer and fluid flow during double-sided laser beam welding of T-joints for aluminum aircraft fuselage panels

Science.gov (United States)

Yang, Zhibin; Tao, Wang; Li, Liqun; Chen, Yanbin; Shi, Chunyuan

2017-06-01

In comparison with conventional laser beam welding, double-sided laser beam welding has two laser heat sources simultaneously and symmetrically loaded from both sides makes it to be a more complicated coupled heat transport and fluid flow process. In this work, in order to understand the heat transfer and fluid flow, a three-dimensional model was developed and validated with the experimental results. The temperature field, fluid flow field, and keyhole characteristic were calculated using the developed model by FLUENT software. Calculated results indicated that the temperature and fluid flow fields were bilateral symmetry along the stringer center, and the molten pool maximum length was located near the keyhole intersection position. The skin side had higher temperature and faster cooling speed. Several characteristic flow patterns in the weld pool cross section, including the vortexes flows near the keyhole opening position, the convection flows above the keyhole intersection location, the regularity downward flows at the molten pool bottom. And in the lengthwise section, a distinct vortex flow below the keyhole, and the liquid metal behind the keyhole first flowed to near the molten pool maximum length location and then to the molten pool surface. Perpendicular to and along welding direction the keyhole liquid metal flowed to the weld molten pool surface and around the keyhole, respectively. The special temperature fields and fluid flow patterns were closely related to the effects of the double sides' laser energy coupling and enhancement. The calculated weld pool geometry basically in good agreement with the experimental results indicated that the developed model was validity and reasonable.

Preschoolers with Autism Spectrum Disorders: Evaluating the Impact of a Home-Based Intervention to Promote Their Communication

Science.gov (United States)

McConkey, Roy; Truesdale-Kennedy, Maria; Crawford, Heather; McGreevy, Elaine; Reavey, Michaela; Cassidy, Arlene

2010-01-01

The complexities that practitioners face in evaluating interventions are illustrated in this article. An early intervention programme (known as Keyhole), based mainly around Treatment and Education of Autistic and related Communications handicapped CHildren (TEACCH), Picture Exchange Communication System (PECS) and Hanen approaches, was delivered…

[Endoscopic assistance in surgery of cerebellopontine angle tumors].

Science.gov (United States)

Poshataev, V K; Shimansky, V N; Tanyashin, S V; Karnaukhov, V V

2014-01-01

During the period of 2010-2012, 33 patients with cerebellopontine angle tumors were operated on at the Burdenko Neurosurgical Institute (Moscow, Russia) using different types of endoscopic assistance. All patients were operated on via the retrosigmoid suboccipital approach in semi-sitting and prone positions. 30° and 70° endoscopes were used during the surgery. Endoscopic assistance allowed us to increase the completeness of tumor removal and to reduce the risk of postoperative complications by retaining the anatomic integrity of cranial nerves and vascular structures in the base of the posterior cranial fossa. These benefits made it possible to maintain and improve quality of life in patients with CPA tumors in the postoperative period.

Facial neuroma masquerading as acoustic neuroma.

Science.gov (United States)

Sayegh, Eli T; Kaur, Gurvinder; Ivan, Michael E; Bloch, Orin; Cheung, Steven W; Parsa, Andrew T

2014-10-01

Facial nerve neuromas are rare benign tumors that may be initially misdiagnosed as acoustic neuromas when situated near the auditory apparatus. We describe a patient with a large cystic tumor with associated trigeminal, facial, audiovestibular, and brainstem dysfunction, which was suspicious for acoustic neuroma on preoperative neuroimaging. Intraoperative investigation revealed a facial nerve neuroma located in the cerebellopontine angle and internal acoustic canal. Gross total resection of the tumor via retrosigmoid craniotomy was curative. Transection of the facial nerve necessitated facial reanimation 4 months later via hypoglossal-facial cross-anastomosis. Clinicians should recognize the natural history, diagnostic approach, and management of this unusual and mimetic lesion. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Percutaneous Transtubular Middle Fossa Approach for Intracanalicular Tumors.

Science.gov (United States)

Bernardo, Antonio; Evins, Alexander I; Tsiouris, Apostolos J; Stieg, Philip E

2015-07-01

In cases of small intracanalicular tumors (≤ 1.5 cm), the middle fossa approach (MFA) provides the ability for adequate tumor removal with preservation of existing auditory function. Application of a minimally invasive tubular retractor in this approach may help mitigate the risk of postoperative seizures, aphasia, and venous complications by minimizing intraoperative retraction of the temporal lobe. We propose a minimally invasive microscopic and/or endoscopic percutaneous transtubular MFA for the management of intracanalicular tumors. Subtemporal keyhole craniectomies were performed on 5 preserved cadaveric heads (10 sides), with 6 sides previously injected with a synthetic tumor model. A ViewSite Brain Access System tubular retractor (Vycor Medical, Inc., Boca Raton, Florida, USA) was used to provide minimal temporal retraction and protection of the surrounding anatomy. An extradural dissection of the internal auditory canal was performed under microscopic and endoscopic visualization with a minimally invasive surgical drill and tube shaft instruments, the intracanalicular tumors were removed, and degree of resection was assessed. All 10 approaches were completed successfully through the tubular retractor with minimal retraction of the temporal lobe. Excellent visualization of the structures within the internal auditory canal was achieved with both the microscope and 3-dimensional endoscope. On the 6 synthetic intracanalicular tumors resected, 5 gross total (Grade I) and 1 near total (Grade II) resections were achieved. A percutaneous transtubular MFA is a feasible minimally invasive option for resection of small intracanalicular tumors with potential preservation of auditory function, reduced temporal retraction, and enhanced protection of surrounding structures. Copyright © 2015 Elsevier Inc. All rights reserved.

Integral Ramjet Booster Demonstration Program

Science.gov (United States)

1975-02-01

vibration loads before motor firing at -65, +70, and +1650F, (2) The chambers are fabricated from roll and welded ( TIG ) L-605 sheet that is cold...Typical Integral Booster Internal Configuration Keyhole Grain Pressure and Thrust Versus Time (+700F, Sea Level) Keyhole Grain Pressure and...Thrust Versus Time (+1650F, Sea Level) Keyhole Grain Pressure and Thrust Versus Time (-65^, Sea Level) Radial-Slot Grain Design Radial-Slot Grain

Plasma Processes of Cutting and Welding

Science.gov (United States)

1976-02-01

TIG process. 2.2.2 Keyhole Welding In plasma arc welding , the term...Cutting 3 3 4 4 4 2.2 Plasma Arc Welding 5 2.2.1 Needle Arc Welding 2.2.2 Keyhole Welding 5 6 3. Applications 8 93.1 Economics 4. Environmental Aspects of...Arc Lengths III. Needle Arc Welding Conditions IV. Keyhole Welding Conditions v. Chemical Analyses of Plates Used - vii - 1. 2. 3. 4. 5. 6. 7. 8.

Plasma ARC Welding of High-Performance-Ship Materials

Science.gov (United States)

1979-05-01

welding (EBW) and laser beam welding (LBW). Figure 2 shows examples of PAW keyhole welds using a square butt joint with and without filler metal additions...produced by some manufacturers has reliability problems. f) Existing equipment for initiating and closing out the keyhole is not totally satisfactory and...system for establishing and closing out keyhole craters is necessary. Work is being done by several Investigators, but it is not known L whether any system

3D Multiphysical Modelling of Fluid Dynamics and Mass Transfer in Laser Welding of Dissimilar Materials

Directory of Open Access Journals (Sweden)

Jiazhou Wu

2018-06-01

Full Text Available A three-dimensional multiphysical transient model was developed to investigate keyhole formation, weld pool dynamics, and mass transfer in laser welding of dissimilar materials. The coupling of heat transfer, fluid flow, keyhole free surface evolution, and solute diffusion between dissimilar metals was simulated. The adaptive heat source model was used to trace the change of keyhole shape, and the Rayleigh scattering of the laser beam was considered. The keyhole wall was calculated using the fluid volume equation, primarily considering the recoil pressure induced by metal evaporation, surface tension, and hydrostatic pressure. Fluid flow, diffusion, and keyhole formation were considered simultaneously in mass transport processes. Welding experiments of 304L stainless steel and industrial pure titanium TA2 were performed to verify the simulation results. It is shown that spatters are shaped during the welding process. The thickness of the intermetallic reaction layer between the two metals and the diffusion of elements in the weld are calculated, which are important criteria for welding quality. The simulation results correspond well with the experimental results.

NAVAIR Portable Source Initiative (NPSI) Data Preparation Standard V2.2: NPSI DPS V2.2

Science.gov (United States)

2012-05-22

Keyhole Markup Language (file format) KMZ ............................................................................. Keyhole Markup...required for the geo-specific texture may differ within the database depending on the mission parameters. When operating close to the ground (e.g

Porosity in fiber laser formation of 5A06 aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Yu, Yang Chun; Wang, Chun Ming; Hu, Xi Yuan; Wang, Jun; Yu, Sheng Fu [HUST, Wuhan (China)

2010-05-15

The mechanism of porosity formation and its suppression methods in laser formation of aluminum alloy have been studied using a 4kW fiber laser to weld 5A06 aluminum alloy with SAl-Mg5 filler. It was found that the porosity formation is closely related to the stability of the keyhole and fluctuation of the molten pool in the laser welding aluminum alloy. The filling wire increased the instability of the keyhole and weld pool, thus further increasing the amount of gas cavities in the joint. Prefabrication of a suitable gap for the butt joint can provide a natural passage for the flow of the liquid metal, which can weaken, and even completely eliminate the disturbance of the filling wire on the formation of keyhole. The gap can also provide a passage for the escape of the bubble. Thus, this method can greatly decrease the sheet's susceptibility to porosity. Moreover, for a thin sheet, if the power of the laser is sufficient to form a keyhole with stable penetration through the weld sheet, a weld bead without porosity can also be obtained because closing the keyhole is almost impossible

Porosity in fiber laser formation of 5A06 aluminum alloy

International Nuclear Information System (INIS)

Yu, Yang Chun; Wang, Chun Ming; Hu, Xi Yuan; Wang, Jun; Yu, Sheng Fu

2010-01-01

The mechanism of porosity formation and its suppression methods in laser formation of aluminum alloy have been studied using a 4kW fiber laser to weld 5A06 aluminum alloy with SAl-Mg5 filler. It was found that the porosity formation is closely related to the stability of the keyhole and fluctuation of the molten pool in the laser welding aluminum alloy. The filling wire increased the instability of the keyhole and weld pool, thus further increasing the amount of gas cavities in the joint. Prefabrication of a suitable gap for the butt joint can provide a natural passage for the flow of the liquid metal, which can weaken, and even completely eliminate the disturbance of the filling wire on the formation of keyhole. The gap can also provide a passage for the escape of the bubble. Thus, this method can greatly decrease the sheet's susceptibility to porosity. Moreover, for a thin sheet, if the power of the laser is sufficient to form a keyhole with stable penetration through the weld sheet, a weld bead without porosity can also be obtained because closing the keyhole is almost impossible

The Supraorbital Keyhole Craniotomy through an Eyebrow Incision: Its Origins and Evolution

Directory of Open Access Journals (Sweden)

D. Ryan Ormond

2013-01-01

Full Text Available In the modern era of neurosurgery, the use of the operative microscope, rigid rod-lens endoscope, and neuronavigation has helped to overcome some of the previous limitations of surgery due to poor lighting and anatomic localization available to the surgeon. Over the last thirty years, the supraorbital craniotomy and subfrontal approach through an eyebrow incision have been developed and refined to play a legitimate role in the armamentarium of the modern skull base neurosurgeon. With careful patient selection, the supraorbital “keyhole” approach offers a less invasive but still efficacious approach to a number of lesions along the subfrontal corridor. Well over 1000 cases have been reported in the literature utilizing this approach establishing its safety and efficacy. This paper discusses the nuances of this approach, including the benefits and limitations of its use described through our technique, review of the literature, and case illustration.

Pore formation during C.W.Nd: YAG laser welding of aluminum alloys for automotive applications

International Nuclear Information System (INIS)

Pastor, M.; Zhao, H.; DebRoy, T.

2000-01-01

Pore formation is an important concern in laser welding of automotive aluminum alloys. This paper investigates the influence of the laser beam defocusing on pore formation during continuous wave Nd:YAG laser welding of aluminum automotive alloys 5182 and 5754. It was found that the instability of the keyhole during welding was a dominant cause of pore formation while hydrogen rejection played an insignificant role. The defocusing of the laser beam greatly affected the stability of the keyhole. Finally, the mechanism of the collapse of the keyhole and pore formation is proposed. (Author) 45 refs

Modeling and design of energy concentrating laser weld joints

Energy Technology Data Exchange (ETDEWEB)

Milewski, J.O. [Los Alamos National Lab., NM (United States); Sklar, E. [OptiCad Corp., Santa Fe, NM (United States)

1997-04-01

The application of lasers for welding and joining has increased steadily over the past decade with the advent of high powered industrial laser systems. Attributes such as high energy density and precise focusing allow high speed processing of precision assemblies. Other characteristics of the process such as poor coupling of energy due to highly reflective materials and instabilities associated with deep penetration keyhole mode welding remain as process limitations and challenges to be overcome. Reflective loss of laser energy impinging on metal surfaces can in some cases exceed ninety five percent, thus making the process extremely inefficient. Enhanced coupling of the laser beam can occur when high energy densities approach the vaporization point of the materials and form a keyhole feature which can trap laser energy and enhance melting and process efficiency. The extreme temperature, pressure and fluid flow dynamics of the keyhole make control of the process difficult in this melting regime. The authors design and model weld joints which through reflective propagation and concentration of the laser beam energy significantly enhance the melting process and weld morphology. A three dimensional computer based geometric optical model is used to describe the key laser parameters and joint geometry. Ray tracing is used to compute the location and intensity of energy absorption within the weld joint. Comparison with experimentation shows good correlation of energy concentration within the model to actual weld profiles. The effect of energy concentration within various joint geometry is described. This method for extending the design of the laser system to include the weld joint allows the evaluation and selection of laser parameters such as lens and focal position for process optimization. The design of narrow gap joints which function as energy concentrators is described. The enhanced laser welding of aluminum without keyhole formation has been demonstrated.

Single access laparoscopic nephrectomy

Directory of Open Access Journals (Sweden)

Jay D Raman

2008-01-01

Full Text Available Laparoscopic nephrectomy has assumed a central role in the management of benign and malignant kidney diseases. While laparoscopy is less morbid than open surgery, it still requires several incisions each at least 1-2 cm in length. Each incision carries morbidity risks of bleeding, hernia and/or internal organ damage, and incrementally decreases cosmesis. An alternative to conventional laparoscopy is single access or keyhole surgery, which utilizes magnetic anchoring and guidance system (MAGS technology or articulating laparoscopic instruments. These technical innovations obviate the need to externally space trocars for triangulation, thus allowing for the creation of a small, solitary portal of entry into the abdomen. Laboratory and early clinical series demonstrate feasibility as well as safe and successful completion of keyhole nephrectomy. Future work is necessary to improve existing instrumentation, increase clinical experience, assess benefits of this surgical approach, and explore other potential applications for this technique.

Minimally invasive neuronavigator-guided microsurgery and photodynamic therapy for gliomas.

Science.gov (United States)

Wang, Yezhong; Lei, Ting; Wang, Zhi

2009-06-01

In order to evaluate the effectiveness of neuronavigator-guided microsurgery and keyhole technique for the resection of gliomas, a total of 60 patients with gliomas were exactly located by using neuronavigator during microsurgery. Forty deep-seated gliomas were resected through a keyhole operative approach. Thirty out of the 60 cases were subjected to photodynamic therapy (PDT) after tumor resection. The therapeutic effectiveness of all the cases was recorded and analyzed. The results showed that glioma was totally resected in 52 cases (86.7%), subtotally in 5 (8.3%), and most partially in 3 (5%). Neurological deficits occurred postoperatively in 4 cases. One patient died of multiple system organ failure 4 days after operation. It was concluded that the application of minimally invasive technique could dramatically decrease surgical complications following resection of glioma, and its combination with PDT could obviously improve the quality of life of patients and prolong the survival time.

Maritime Threat Detection using Plan Recognition

Science.gov (United States)

2012-11-01

operate in close proximity to large but much less maneuverable vessels. Various approaches for automated threat and anomaly detection have been...version space techniques, and other closed -world reasoning algorithms, while probabilistic algorithms include those that use stochastic grammars and...differ along many dimensions, such as their agent relation (e.g., keyhole , intention, adversarial), what they infer (e.g., action, plan, goal

Snacks With Nutrition Labels: Tastiness Perception, Healthiness Perception, and Willingness to Pay by Norwegian Adolescents.

Science.gov (United States)

Wang, Qing; Oostindjer, Marije; Amdam, Gro V; Egelandsdal, Bjørg

2016-02-01

Consumers tend to have the perception that healthy equals less tasty. This study aimed to identify whether information provided by the Keyhole symbol, a widely used front-of-package symbol in Nordic countries to indicate nutritional content, and percent daily values (%DVs) affect Norwegian adolescents' perception of the healthiness of snacks and their intention to buy them. Two tasks were used to evaluate adolescents' perception of snacks with the Keyhole symbol: with %DVs or with no nutrition label. A third task was used to test their abilities to use %DVs (pairwise selections). A survey obtained personal attributes. A total of 566 Norwegian adolescents. Taste perception, health perception, and ability to use %DVs. Linear mixed models and logistic models that tested effects of labels and personal attributes on main outcome measures. The Keyhole symbol increased health perception without influencing taste perception of snacks. Norwegian adolescents had limited abilities to use information from the %DVs correctly to identify healthier foods. Norwegian adolescents had a positive perception of the Keyhole symbols. Keyhole symbols as a simple, heuristic front-of-package label have potential as an information strategy that may influence self-efficacy in promoting healthy snack choices among adolescents. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

Nonstationary plasma-thermo-fluid dynamics and transition in processes of deep penetration laser beam-matter interaction

Science.gov (United States)

Golubev, Vladimir S.; Banishev, Alexander F.; Azharonok, V. V.; Zabelin, Alexandre M.

1994-09-01

A qualitative analysis of the role of some hydrodynamic flows and instabilities by the process of laser beam-metal sample deep penetration interaction is presented. The forces of vapor pressure, melt surface tension and thermocapillary forces can determined a number of oscillatory and nonstationary phenomena in keyhole and weld pool. Dynamics of keyhole formation in metal plates has been studied under laser beam pulse effect ((lambda) equals 1.06 micrometers ). Velocities of the keyhole bottom motion have been determined at 0.5 X 105 - 106 W/cm2 laser power densities. Oscillatory regime of plate break- down has been found out. Small-dimensional structures with d-(lambda) period was found on the frozen cavity walls, which, in our opinion, can contribute significantly to laser beam absorption. A new form of periodic structure on the frozen pattern being a helix-shaped modulation of the keyhole walls and bottom relief has been revealed. Temperature oscillations related to capillary oscillations in the melt layer were discovered in the cavity. Interaction of the CW CO2 laser beam and the matter by beam penetration into a moving metal sample has been studied. The pulsed and thermodynamic parameters of the surface plasma were investigated by optical and spectroscopic methods. The frequencies of plasma jets pulsations (in 10 - 105 Hz range) are related to possible melt surface instabilities of the keyhole.

[Laparoscopic approach in large hiatal hernia--particular considerations].

Science.gov (United States)

Munteanu, R; Copăescu, C; Iosifescu, R; Timişescu, Lucia; Dragomirescu, C

2003-01-01

Large hiatal hernia are associated with permanent or intermittent protrusion of more than 1/3 of the stomach into the chest, single or in associated with other organs, a hiatal defect greater than 5 cm and various complications related to the morphological and physiological modifications. While the laparoscopic approach in small hiatal hernia and gastro-esophageal reflux disease is a standard procedure in large hiatal hernia persists a number of questions and controversies. Between 1995 and 2002 a number of 23 patients with large hiatal hernia (9 men, 14 women), mean age 65.8 years (range 49 to 77) underwent laparoscopic surgery. The majority of the patients had complications of the disease (dysphagia, severe esophagitis, anemia, respiratory and cardiac failure). In 16 cases was a sliding hernia (one recurrent after open procedure), in 2 paraesophageal and in 5 a mixed hernia (two "upside-down" type). In 7 cases we perform, in the same operation, cholecystectomy for gallbladder stones and in one cases Heller myotomy for achalasia. In all cases the repairs was performed by using interrupted stitches to approximate the crurae, but in three of them (recurrent and upside down hernia) we consider necessary to repair with a polypropylene mesh (10 x 5 cm) with a "keyhole" for the esophagus. In these particular cases we do not perform a antireflux procedure, in others 20 cases a short floppy Nissen was done. During the operation one patient developed a left pneumothorax and required pleural drainage. Postoperatively one patient had dysphagia treated by pneumatic dilatation and another die 3 weeks after the surgery because severe respiratory and cardiac failure. Laparoscopic approach is a feasible and effective procedure with good postoperatively results, but required good skills in mininvasive technique.

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

In the present study, the vorticity of melt motion in the keyhole and weld pool has been evaluated in case of high power CO2 laser beam welding. The circulation of vorticity is obtained as a function of Reynolds number for a given keyhole volume which is linked to Mach number variation. The shear stress and thermal fluxes ...

Dairy Cows Naturally Infected with Bovine Leukemia Virus Exhibit Abnormal B- and T-Cell Phenotypes after Primary and Secondary Exposures to Keyhole Limpet Hemocyanin

Science.gov (United States)

Frie, Meredith C.; Sporer, Kelly R. B.; Benitez, Oscar J.; Wallace, Joseph C.; Droscha, Casey J.; Bartlett, Paul C.; Coussens, Paul M.

2017-01-01

Bovine leukemia virus (BLV) is a retrovirus that is highly prevalent in US dairy herds: over 83% are BLV infected and the within-herd infection rate can be almost 50% on average. While BLV is known to cause lymphosarcomas, only 5% or fewer infected cattle will develop lymphoma; this low prevalence of cancer has historically not been a concern to dairy producers. However, more recent research has found that BLV+ cows without lymphoma produce less milk and have shorter lifespans than uninfected herdmates. It has been hypothesized that BLV infection interferes with normal immune function in infected cattle, and this could lead to reduced dairy production. To assess how naturally infected BLV+ cows responded to a primary and secondary immune challenge, 10 BLV+ and 10 BLV− cows were injected subcutaneously with keyhole limpet hemocyanin (KLH) and dimethyldioctadecylammonium bromide. B- and T-cell responses were characterized over the following 28 days. A total of 56 days after primary KLH exposure, cows were re-injected with KLH and B- and T-cell responses were characterized again over the following 28 days. BLV+ cows produced less KLH-specific IgM after primary immune stimulation; demonstrated fewer CD45R0+ B cells, altered proportions of CD5+ B cells, altered expression of CD5 on CD5+ B cells, and reduced MHCII surface expression on B cells ex vivo; exhibited reduced B-cell activation in vitro; and displayed an increase in BLV proviral load after KLH exposure. In addition, BLV+ cows had a reduced CD45R0+γδ+ T-cell population in the periphery and demonstrated a greater prevalence of IL4-producing T cells in vitro. All together, our results demonstrate that both B- and T-cell immunities are disrupted in BLV+ cows and that antigen-specific deficiencies can be detected in BLV+ cows even after a primary immune exposure. PMID:28770217

Semicircular Horizontal Approach in Breast Reduction: Clinical Experience in 38 Cases

Directory of Open Access Journals (Sweden)

Hee Su Shin

2015-07-01

Full Text Available BackgroundVarious techniques are used for performing breast reduction. Wise-pattern and vertical scar techniques are the most commonly employed approaches. However, a vertical scar in the mid-lower breast is prominent and aesthetically less pleasant. In contrast, a semicircular horizontal approach does not leave a vertical scar in the mid breast and transverse scars can be hidden in the inframammary fold. In this paper, we describe the experiences and results of semicircular horizontal breast reductions performed by a single surgeon.MethodsBetween September 1996 and October 2013, our senior author used this technique in 38 cases in the US and at our institution. We used a superiorly based semicircular incision, where the upper skin paddle was pulled down to the inframammary fold with the nipple-areola complex pulled through the keyhole.ResultsThe average total reduction per breast was 584 g, ranging from 286 to 794 g. The inferior longitudinal pedicle was used in all the cases. The average reduction of the distance from the sternal notch to the nipple was 13 cm (range, 11-15 cm. The mean decrease in the bra cup size was 1.7 cup sizes (range, a decrease of 1 to 3. We obtained very satisfactory results with a less noticeable scar, no complication such as necrosis of the nipple or the skin flap, wound infection, aseptic necrosis of the breast tissue, or wound dehiscence. One patient had a small hematoma that resolved spontaneously.ConclusionsThis technique is straightforward and easy to learn, and offers a safe, effective, and predictable way for treating mammary hypertrophy.

Kilimanjaro through the keyhole.

Science.gov (United States)

Parkin, Amanda

2011-01-01

Amanda Parkin, marketing manager at approved design and build consultant to the NHS for integrated theatres and digital video communications, OR Networks, explains how, with the help of the company and its specialist equipment, Northumbrian surgeons successfully established a two-way audio/video link to their counterparts at a hospital in the foothills of Mount Kilimanjaro to enable them to train the Tanzanian surgeons in laparoscopic surgery. Alongside opening up many new teaching opportunities in both the UK and Tanzania, the link-up has already saved countless lives.

Formación de porosidad durante la soldadura láser de Nd: YAG de onda continua en aleaciones de aluminio para aplicaciones automotrices

Directory of Open Access Journals (Sweden)

Pastor, Mario

2000-04-01

Full Text Available Pore formation is an important concern in laser welding of automotive aluminum alloys. This paper investigates the influence of the laser beam defocusing on pore formation during continuous wave Nd: YAG laser welding of aluminum automotive alloys 5182 and 5754. It was found that the instability of the keyhole during welding was a dominant cause of pore formation while hydrogen rejection played an insignificant role. The defocusing of the laser beam greatly affected the stability of the keyhole. Finally, the mechanism of the collapse of the keyhole and pore formation is proposed.

La formación de poros es un aspecto de gran preocupación durante la soldadura láser de aleaciones de aluminio. En este trabajo se ha investigado la influencia del desenfoque del haz del láser sobre la formación de poros durante la soldadura láser (Nd: YAG de onda continua de las aleaciones de aluminio 5182 y 5754, las mismas que se usan en aplicaciones automotrices. Los resultados obtenidos indicaron que la causa dominante de formación de poros fue la inestabilidad de la cavidad de vapor o keyhole mientras que la influencia del hidrógeno fue prácticamente insignificante. El grado de desenfoque del láser tuvo gran influencia sobre la inestabilidad de la cavidad de vapor. Finalmente, en este artículo se propone el mecanismo de formación de poros a causa del colapso de la cavidad de vapor (keyhole.

Titanium 󈨠: Science and Technology. Proceedings of a Symposium Sponsored by the Titanium Committee of the Minerals, Metals and Materials Structural Metals Division Held at the World Titanium Conference (7th) in San Diego, California on June 29-July 2, 1992. Volume 2

Science.gov (United States)

1993-01-01

the TIG Welding of Commercially Pure Titanium Sheet ........................................................... 1,601 M.F. Gittos and M.M. Scott An...the welding current and the plasma gas flow rate are such that the plasma penetrates completely through the workpiece ( keyhole technique). A double...necessary. The maximum weldable thickness in keyhole welding was 18 mm. However, penetration became less regular. The optimum welding conditions with a 16 mm

Material Properties of Laser-Welded Thin Silicon Foils

Directory of Open Access Journals (Sweden)

M. T. Hessmann

2013-01-01

Full Text Available An extended monocrystalline silicon base foil offers a great opportunity to combine low-cost production with high efficiency silicon solar cells on a large scale. By overcoming the area restriction of ingot-based monocrystalline silicon wafer production, costs could be decreased to thin film solar cell range. The extended monocrystalline silicon base foil consists of several individual thin silicon wafers which are welded together. A comparison of three different approaches to weld 50 μm thin silicon foils is investigated here: (1 laser spot welding with low constant feed speed, (2 laser line welding, and (3 keyhole welding. Cross-sections are prepared and analyzed by electron backscatter diffraction (EBSD to reveal changes in the crystal structure at the welding side after laser irradiation. The treatment leads to the appearance of new grains and boundaries. The induced internal stress, using the three different laser welding processes, was investigated by micro-Raman analysis. We conclude that the keyhole welding process is the most favorable to produce thin silicon foils.

Heat Source - Materials Interactions during Fusion Welding.

Science.gov (United States)

1982-04-30

the capabilities of ultrasonic weld pool measurement, and to address questions of applications to active pool size control. -- mom- 44 TIG welding ...preparation. The fraction of absorbed power increases dramatically upon formation of a keyhole . As a result, welds made with sharply beveled edge...laser end electron beam welding processes characteristically produce a deel,, narrow weld bead. This bead is formed by a keyhole mode of operation in

Visualization Development of the Ballistic Threat Geospatial Optimization

Science.gov (United States)

2015-07-01

topographic globes, Keyhole Markup Language (KML), and Collada files. World Wind gives the user the ability to import 3-D models and navigate...present. After the first person view window is closed , the images stored in memory are then converted to a QuickTime movie (.MOV). The video will be...processing unit HPC high-performance computing JOGL Java implementation of OpenGL KML Keyhole Markup Language NASA National Aeronautics and Space

High-Bandwidth Tactical-Network Data Analysis in a High-Performance-Computing (HPC) Environment: Packet-Level Analysis

Science.gov (United States)

2015-09-01

individual fragments using the hash-based method. In general, fragments 6 appear in order and relatively close to each other in the file. A fragment...data product derived from the data model is shown in Fig. 5, a Google Earth12 Keyhole Markup Language (KML) file. This product includes aggregate...System BLOb binary large object FPGA field-programmable gate array HPC high-performance computing IP Internet Protocol KML Keyhole Markup Language

Nd:YAG laser welding of aerospace grade ZE41A magnesium alloy: Modeling and experimental investigations

International Nuclear Information System (INIS)

Al-Kazzaz, H.; Medraj, M.; Cao, X.; Jahazi, M.

2008-01-01

Keyhole formation as well as the geometry of weld profiles during Nd:YAG laser welding of ZE41A-T5 were studied through combining various models and concepts. The results indicated that weld width and fusion area decrease with increasing welding speed. In the case of partially penetrated welding, penetration depth decreases with increasing welding speed. Also, the model predicted that excessive decrease in laser power or increase in defocusing distance decreases surface power density, thereby changing the welding mode from fully penetrated keyhole, to partially penetrated keyhole, and then to the conduction mode. The predicted conditions for keyhole stability and welding modes as well as the weld profiles for various processing conditions were validated by some selected welding experiments. These experiments included studying the effects of welding speed, laser power, joint gap and laser defocusing on the weld geometry of 2- and 6-mm butt joints or bead-on-plates of ZE41A-T5 sand castings using a continuous wave 4 kW Nd:YAG laser system and 1.6-mm EZ33A-T5 filler wire. Good agreements were found between the model predictions and experimental results indicating the validity of the assumptions made for the development of the model

Characterization of duplex stainless steel weld metals obtained by hybrid plasma-gas metal arc welding

OpenAIRE

Yurtisik,Koray; Tirkes,Suha; Dykhno,Igor; Gur,C. Hakan; Gurbuz,Riza

2013-01-01

Despite its high efficiency, autogenous keyhole welding is not well-accepted for duplex stainless steels because it causes excessive ferrite in as-welded duplex microstructure, which leads to a degradation in toughness and corrosion properties of the material. Combining the deep penetration characteristics of plasma arc welding in keyhole mode and metal deposition capability of gas metal arc welding, hybrid plasma - gas metal arc welding process has considered for providing a proper duplex mi...

Laser beam welding of titanium additive manufactured parts

OpenAIRE

Wits, Wessel Willems; Jauregui Becker, Juan Manuel

2015-01-01

In this paper the joinability of titanium Additive Manufactured (AM) parts is explored. Keyhole welding, using a pulsed laser beam, of conventionally produced parts is compared to AM parts. Metal AM parts are notorious for having remaining porosities and other non-isotropic properties due to the layered manufacturing process. This study shows that due to these deficiencies more energy per unit weld length is required to obtain a similar keyhole geometry for titanium AM parts. It is also demon...

Case-Based Policy and Goal Recognition

Science.gov (United States)

2015-09-30

Policy and Goal Recognizer (PaGR), a case- based system for multiagent keyhole recognition. PaGR is a knowledge recognition component within a decision...However, unlike our agent in the BVR domain, these recognition agents have access to perfect information. Single-agent keyhole plan recognition can be...listed below: 1. Facing Target 2. Closing on Target 3. Target Range 4. Within a Target’s Weapon Range 5. Has Target within Weapon Range 6. Is in Danger

Initial Parameter Estimation for Inverse Thermal Analysis of Ti-6Al-4V Deep Penetration Welds

Science.gov (United States)

2014-05-16

theory, for the case of deep-penetration welding, is simulation of the coupling of keyhole formation, melting, fluid flow in the weld melt pool and...isothermal boundaires, e.g., TTB and TM. A specific procedure for interpolation, however, has not been considered. For the present study, the close ...Clarendon Press, Oxford, 2nd ed, 374, 1959. 19. R. Rai, J.W. Elmer, T.A. Palmer, T. DebRoy, Heat Transfer and Fluid Flow During Keyhole Mode Laser Welding

Joining Pipe with the Hybrid Laser-GMAW Process: Weld Test Results and Cost Analysis

Science.gov (United States)

2006-06-01

GMAW head separations an additional gas nozzle directed N2 gas at the laser keyhole for plasma suppression and supplemental shielding. Experiments were...beam weld and GMA weld taking place simultaneously in close prox- i m i t y. It has been noted in the literature that hy- brid often refers to laser ...near the beginning and end of the weld. Laser beam keyhole instability may be the cause. Ongoing investigations are being undertaken to determine the

Numerical simulation of electron beam welding with beam oscillations

Science.gov (United States)

Trushnikov, D. N.; Permyakov, G. L.

2017-02-01

This research examines the process of electron-beam welding in a keyhole mode with the use of beam oscillations. We study the impact of various beam oscillations and their parameters on the shape of the keyhole, the flow of heat and mass transfer processes and weld parameters to develop methodological recommendations. A numerical three-dimensional mathematical model of electron beam welding is presented. The model was developed on the basis of a heat conduction equation and a Navier-Stokes equation taking into account phase transitions at the interface of a solid and liquid phase and thermocapillary convection (Marangoni effect). The shape of the keyhole is determined based on experimental data on the parameters of the secondary signal by using the method of a synchronous accumulation. Calculations of thermal and hydrodynamic processes were carried out based on a computer cluster, using a simulation package COMSOL Multiphysics.

Postoperative Submandibular Gland Swelling following Craniotomy under General Anesthesia

Directory of Open Access Journals (Sweden)

Haruka Nakanishi

2015-01-01

Full Text Available Objective. Reporting of a rare case of postoperative submandibular gland swelling following craniotomy. Case Report. A 33-year-old male underwent resection for a brain tumor under general anesthesia. The tumor was resected via a retrosigmoid suboccipital approach and the patient was placed in a lateral position with his face down and turned to the right. Slight swelling of the right submandibular gland was observed just after the surgery. Seven hours after surgery, edematous change around the submandibular gland worsened and he required emergent reintubation due to airway compromise. The cause of submandibular gland swelling seemed to be an obstruction of the salivary duct due to surgical positioning. Conclusion. Once submandibular swelling and edematous change around the submandibular gland occur, they can worsen and compromise the air way within several hours after operation. Adequate precaution must be taken for any predisposing skull-base surgery that requires strong cervical rotation and flexion.

Triple Arterial Phase MR Imaging with Gadoxetic Acid Using a Combination of Contrast Enhanced Time Robust Angiography, Keyhole, and Viewsharing Techniques and Two-Dimensional Parallel Imaging in Comparison with Conventional Single Arterial Phase

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jeong Hee [Department of Radiology, Seoul National University Hospital, Seoul 03080 (Korea, Republic of); Department of Radiology, Seoul National University College of Medicine, Seoul 03087 (Korea, Republic of); Lee, Jeong Min [Department of Radiology, Seoul National University Hospital, Seoul 03080 (Korea, Republic of); Department of Radiology, Seoul National University College of Medicine, Seoul 03087 (Korea, Republic of); Institute of Radiation Medicine, Seoul National University Medical Research Center, Seoul 03087 (Korea, Republic of); Yu, Mi Hye [Department of Radiology, Konkuk University Medical Center, Seoul 05030 (Korea, Republic of); Kim, Eun Ju [Philips Healthcare Korea, Seoul 04342 (Korea, Republic of); Han, Joon Koo [Department of Radiology, Seoul National University Hospital, Seoul 03080 (Korea, Republic of); Department of Radiology, Seoul National University College of Medicine, Seoul 03087 (Korea, Republic of); Institute of Radiation Medicine, Seoul National University Medical Research Center, Seoul 03087 (Korea, Republic of)

2016-11-01

To determine whether triple arterial phase acquisition via a combination of Contrast Enhanced Time Robust Angiography, keyhole, temporal viewsharing and parallel imaging can improve arterial phase acquisition with higher spatial resolution than single arterial phase gadoxetic-acid enhanced magnetic resonance imaging (MRI). Informed consent was waived for this retrospective study by our Institutional Review Board. In 752 consecutive patients who underwent gadoxetic acid-enhanced liver MRI, either single (n = 587) or triple (n = 165) arterial phases was obtained in a single breath-hold under MR fluoroscopy guidance. Arterial phase timing was assessed, and the degree of motion was rated on a four-point scale. The percentage of patients achieving the late arterial phase without significant motion was compared between the two methods using the χ{sup 2} test. The late arterial phase was captured at least once in 96.4% (159/165) of the triple arterial phase group and in 84.2% (494/587) of the single arterial phase group (p < 0.001). Significant motion artifacts (score ≤ 2) were observed in 13.3% (22/165), 1.2% (2/165), 4.8% (8/165) on 1st, 2nd, and 3rd scans of triple arterial phase acquisitions and 6.0% (35/587) of single phase acquisitions. Thus, the late arterial phase without significant motion artifacts was captured in 96.4% (159/165) of the triple arterial phase group and in 79.9% (469/587) of the single arterial phase group (p < 0.001). Triple arterial phase imaging may reliably provide adequate arterial phase imaging for gadoxetic acid-enhanced liver MRI.

Triple arterial phase MR imaging with gadoxetic acid using a combination of contrast enhanced time robust angiography, keyhole, and viewsharing techniques and two-dimensional parallel imaging in comparison with conventional single arterial phase

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jeong Hee; Lee, Jeong Min; Han, Joon Koo [Dept. of Radiology, Seoul National University Hospital, Seoul (Korea, Republic of); Yu, Mi Hye [Dept. of Radiology, Konkuk University Medical Center, Seoul (Korea, Republic of); Kim, Eun Ju [Philips Healthcare Korea, Seoul (Korea, Republic of)

2016-07-15

To determine whether triple arterial phase acquisition via a combination of Contrast Enhanced Time Robust Angiography, keyhole, temporal viewsharing and parallel imaging can improve arterial phase acquisition with higher spatial resolution than single arterial phase gadoxetic-acid enhanced magnetic resonance imaging (MRI). Informed consent was waived for this retrospective study by our Institutional Review Board. In 752 consecutive patients who underwent gadoxetic acid-enhanced liver MRI, either single (n = 587) or triple (n = 165) arterial phases was obtained in a single breath-hold under MR fluoroscopy guidance. Arterial phase timing was assessed, and the degree of motion was rated on a four-point scale. The percentage of patients achieving the late arterial phase without significant motion was compared between the two methods using the χ2 test. The late arterial phase was captured at least once in 96.4% (159/165) of the triple arterial phase group and in 84.2% (494/587) of the single arterial phase group (p < 0.001). Significant motion artifacts (score ≤ 2) were observed in 13.3% (22/165), 1.2% (2/165), 4.8% (8/165) on 1st, 2nd, and 3rd scans of triple arterial phase acquisitions and 6.0% (35/587) of single phase acquisitions. Thus, the late arterial phase without significant motion artifacts was captured in 96.4% (159/165) of the triple arterial phase group and in 79.9% (469/587) of the single arterial phase group (p < 0.001). Triple arterial phase imaging may reliably provide adequate arterial phase imaging for gadoxetic acid-enhanced liver MRI.

Piezosurgery as a further technical adjunct in minimally invasive supraorbital keyhole approach and lateral orbitotomy.

Science.gov (United States)

Iacoangeli, Maurizio; Di Rienzo, Alessandro; Nocchi, Niccolo; Balercia, Paolo; Lupi, Ettore; Regnicolo, Luana; Di Somma, Lucia Giovanna Maria; Alvaro, Lorenzo; Scerrati, Massimo

2015-03-01

One of the problems in neurosurgery is how to perform rapid and effective craniotomies that minimize the risk of injury to underlying eloquent structures. The traditional high-powered pneumatic tools and saws are efficient in terms of speed and penetration, but they can provoke bone necrosis and sometimes damage neurovascular structures. As an alternative, we evaluated the piezoelectric bone scalpel (piezosurgery), a device that potentially allows thinner and more precise bone cutting without lesioning neighboring delicate structures, even in the case of accidental contact. From January 2009 to December 2011, 20 patients (8 men and 12 women), 19 to 72 years of age (mean: 49.3 years) were treated using piezosurgery. Surgery was performed for the removal of anterior cranial fossa meningiomas, orbital tumors, and sinonasal lesions with intracranial extension. The time required to perform craniotomy using piezosurgery is a few minutes longer than with traditional drills. No damage was observed using the piezoelectric device. Follow-up clinical and neuroradiologic evaluation showed a faster and better ossification of the bone flap with good esthetic results. Piezosurgery is a new promising technique for selective bone cutting with soft tissue preservation. This instrument seems suitable to perform precise thin osteotomies while limiting damage to the bone itself and to the underlying delicate structures even in the case of unintentional contact. These advantages make the piezoelectric bone scalpel a particularly attractive instrument in neurosurgery. Georg Thieme Verlag KG Stuttgart · New York.

GIBS Keyhole Markup Language (KML)

Data.gov (United States)

National Aeronautics and Space Administration — The KML documentation standard provides a solution for imagery integration into mapping tools that utilize support the KML standard, specifically Google Earth. Using...

The impact of price reductions on individuals' choice of healthy meals away from home

DEFF Research Database (Denmark)

Nordström, Leif Jonas; Thunström, Linda

Food high in energy but low in nutritional value is an important contributor to several serious illnesses, and one type of food that is particularly high in energy but low in nutrition is food consumed away from home. In this paper, we examine the demand and willingness to pay for healthy, Keyhol...... of individuals who already have a relatively good nutritional intake would select the healthy option. Groups with a generally poor nutritional intake (men and individuals with lower education and lower income) would gain health benefits from a subsidy of Keyhole-labelled meals....

Immunotherapeutic effect of Concholepas hemocyanin in the murine bladder cancer model: evidence for conserved antitumor properties among hemocyanins.

Science.gov (United States)

Moltedo, Bruno; Faunes, Fernando; Haussmann, Denise; De Ioannes, Pablo; De Ioannes, Alfredo E; Puente, Javier; Becker, María Inés

2006-12-01

We determined the antitumor properties of a newly available hemocyanin obtained from the Chilean gastropod Concholepas concholepas (Biosonda Corp., Santiago, Chile) in a syngeneic heterotopic mouse bladder carcinoma model. Since keyhole limpet hemocyanin (Pierce, Rockford, Illinois) is used increasingly in biomedicine as a carrier for vaccines and an immunotherapeutic agent for bladder transitional cell carcinoma, there is a growing interest in finding new substances that share its potent immunomodulatory properties. Considering that keyhole limpet hemocyanin and Concholepas concholepas hemocyanin differ significantly, it was not possible to predict a priori the antitumor properties of Concholepas concholepas hemocyanin. C3H/He mice were primed with Concholepas concholepas hemocyanin before subcutaneous implantation of mouse bladder tumor-2 cells. Treatment consisted of a subcutaneous dose of Concholepas concholepas hemocyanin (1 mg or 100 mug) at different intervals after implantation. Keyhole limpet hemocyanin and phosphate buffered saline served as positive and negative controls, respectively. In addition, experiments were designed to determine which elements of the immune response were involved in its adjuvant immunostimulatory effect. Mice treated with Concholepas concholepas hemocyanin showed a significant antitumor effect, as demonstrated by decreased tumor growth and incidence, prolonged survival and lack of toxic effects. These effects were similar to those achieved with keyhole limpet hemocyanin. We found that each hemocyanin increased natural killer cell activity but the effect of Concholepas concholepas hemocyanin was stronger. Analysis of serum from treated mice showed an increased interferon-gamma and low interleukin-4, which correlated with antibody isotypes, confirming that hemocyanins induce a T helper type 1 cytokine profile. To our knowledge our results are the first demonstration of the antitumor effect of a hemocyanin other than keyhole limpet

The influence of laser pulse waveform on laser-TIG hybrid welding of AZ31B magnesium alloy

Science.gov (United States)

Song, Gang; Luo, Zhimin

2011-01-01

By dividing laser pulse duration into two parts, three kinds of laser waveforms are designed, including a high power density pulse (HPDP) laser in a short duration set at the beginning of the laser waveform. This paper aims to find out the laser pulse waveform and idiographic critical values of HPDP, which can affect the magnesium penetration in laser-tungsten inert gas (TIG) hybrid welding. Results show that when the laser pulse duration of HPDP is not more than 0.4 ms, the welding penetration values of lasers with HPDP are larger than otherwise. Also, the welding penetration values of laser with HPDP have increased by up to 26.1%. It has been found that with HPDP, the laser can form the keyhole more easily because the interaction between laser and the plate is changed, when the TIG arc preheats the plate. Besides, the laser with high power density and short duration strikes on the plates so heavily that the corresponding background power can penetrate into the bottom of the keyhole and maintain the keyhole open, which facilitates the final welding penetration.

An analysis of the effects of a campaign supporting use of a health symbol on food sales and shopping behaviour of consumers

DEFF Research Database (Denmark)

Mørk, Trine; Grunert, Klaus G; Fenger, Morten H. J.

2017-01-01

Background: Since 2009, the green Keyhole symbol has been a joint Nordic initiative for signalling healthfulness of specific food products. In 2014, the Danish Ministry of Food, Agriculture and Fisheries carried out a campaign aimed mainly at men over 35 with a low level of education, encouraging...... labelled products rose by about 20%. In the third chain, there was a slight decrease of sales of Keyhole labelled products. The effect differed considerably between product categories. Analysis of the interview data indicated that by the end of the campaign, shoppers with a short education had a higher...

Human-Robot Interaction

Science.gov (United States)

Sandor, Aniko; Cross, E. Vincent, II; Chang, Mai Lee

2015-01-01

Human-robot interaction (HRI) is a discipline investigating the factors affecting the interactions between humans and robots. It is important to evaluate how the design of interfaces affect the human's ability to perform tasks effectively and efficiently when working with a robot. By understanding the effects of interface design on human performance, workload, and situation awareness, interfaces can be developed to appropriately support the human in performing tasks with minimal errors and with appropriate interaction time and effort. Thus, the results of research on human-robot interfaces have direct implications for the design of robotic systems. For efficient and effective remote navigation of a rover, a human operator needs to be aware of the robot's environment. However, during teleoperation, operators may get information about the environment only through a robot's front-mounted camera causing a keyhole effect. The keyhole effect reduces situation awareness which may manifest in navigation issues such as higher number of collisions, missing critical aspects of the environment, or reduced speed. One way to compensate for the keyhole effect and the ambiguities operators experience when they teleoperate a robot is adding multiple cameras and including the robot chassis in the camera view. Augmented reality, such as overlays, can also enhance the way a person sees objects in the environment or in camera views by making them more visible. Scenes can be augmented with integrated telemetry, procedures, or map information. Furthermore, the addition of an exocentric (i.e., third-person) field of view from a camera placed in the robot's environment may provide operators with the additional information needed to gain spatial awareness of the robot. Two research studies investigated possible mitigation approaches to address the keyhole effect: 1) combining the inclusion of the robot chassis in the camera view with augmented reality overlays, and 2) modifying the camera

At grade optical crossover for monolithic optial circuits

Science.gov (United States)

Jamieson, Robert S. (Inventor)

1983-01-01

Planar optical circuits may be made to cross through each other, (thus eliminating extra steps required to fabricate elevated, nonintersecting crossovers) by control of the dimensions of the crossing light conductors (10, 12) to be significantly greater than d=0.89.lambda. and the angle of crossing as nearly 90.degree. as conveniently possible. A light trap may be provided just ahead of the intersection to trap any light being reflected in the source conductor at angles greater than about 45.degree.. The light trap may take the form of triangular shaped portions (16a, 16b) on each side of the source conductor with the far side of the triangular portion receiving incident light at an angle so that incident light will be reflected to the other side, or it may take the form of windows (18a, 18b) in place of the triangular portions. Planar optical circuit boards (21-23) may be fabricated and stacked to form a keyboard (20) with intersecting conductors (26-29) and keyholes (0-9) where conductors merge at the broad side of the circuit boards. These keyholes may be prearranged to form an array or matrix of keyholes.

The Keyhole[R] Rainbow Resource Kit: Meeting the Needs of Parents of Newly Diagnosed Preschoolers with ASD

Science.gov (United States)

McConkey, Roy; MacLeod, Sue; Cassidy, Arlene

2011-01-01

A resource kit containing information booklets about ASD, selected toys and playthings, and communication aids was developed and evaluated with 29 volunteer mothers supported by service personnel who visited on an average of six occasions. A mix of qualitative and quantitative methodologies was used in the evaluation. Nearly all mothers found the…

A comparison of four dimensional time-resolved with keyhole and three dimensional time-of-flight MR angiography for the evaluation of cerebral aneurysms

International Nuclear Information System (INIS)

Wu Qian; Li Minghua; Zhang Jiayin; Li Yongdong

2012-01-01

Objective: To evaluate the accuracy and reliability of 4D time-resolved MRA with keyhole (4D-TRAK) for the detection and characterization of cerebral aneurysms (CAs), with a comparison of 3D time-of-flight MRA (3D-TOF-MRA). Methods: 3D-TOF-MRA, 4D-TRAK and 3D-DSA were performed sequentially in 52 patients with suspected CAs. 4D-TRAK was acquired using a combination of sensitivity encoding (SENSE) and contrast-enhanced (CE) timing robust angiography (CENTRA) k-space sampling techniques at a contrast dose of 10 ml at 3 T scanner. Accuracy, sensitivity, specificity of 4D-TRAK and 3D-TOF-MRA were calculated and compared for the detection of CAs on patient-based and aneurysm-based evaluation using 3D-DSA as a reference. Wilcoxon signed rank test were used. Results: The overall image quality of 4D-TRAK was appropriate for the diagnostic purpose, but yet not comparable with that of 3D-TOF-MRA. In 52 patients with suspected GAs, 58 CAs were confirmed on 3D-DSA finally.Fifty-one (with 2 false-positives and 9 false-negatives) and 58 (with 1 false-positive and 1 false-negative) CAs were visualized on 4D-TRAK and 3D-TOF-MRA, respectively. Accuracy, sensitivity and specificity on patient-based evaluation of 4D-TRAK and 3D-TOF-MRA were 92.31% (48/52), 93.33% (42/45), 85.71 % (6/7) and 98.08% (51/52), 100.00% (45/45), 85.71% (6/7), respectively, and 74.07% (20/27), 75.00% (18/24), 66.67% (2/3) and 96.30% (26/27), 95.83% (26/27), 100.00% (3/3) on aneurysm-based evaluation in patients with multiple CAs, respectively. Subgroup analysis revealed that for 19 very small CAs (maximal diameter <3 mm,measured on 3D-DSA), 9 were missed on 4D-TRAK and 1 on 3D-TOF-MRA (Z=-2.464, P0.05). In 4 large CAs with maximal diameter more than 10 mm, 4D-TRAK provided a better characterization of morphology than 3D

Tungsten chemical vapor deposition characteristics using SiH4 in a single wafer system

International Nuclear Information System (INIS)

Rosler, R.S.; Mendonca, J.; Rice, M.J. Jr.

1988-01-01

Several workers have recently begun using silane as a high-rate, low-temperature alternative to hydrogen for the reduction of WF 6 in the chemical vapor deposition of W. The deposition and film characteristics of both selective and blanket W using this new chemistry are explored in a radiantly heated single wafer system using closed-loop temperature control with a thermocouple in direct contact with the backside of the wafer. Selective W deposition rates of up to 1.5 μm/min were measured over the temperature range 250--550 0 C with blanket W rates typically 2--5 x lower. Resistivity is in the 10--15 μΩcm range at 300 0 C for SiH 4 /WF 6 ratios of 0.2 to 1.0, while above 400 0 C the range is 7.5--8.5 μΩcm. Si content in the W films is quite low at 10 16 to 10 17 atoms/cm 3 . Adhesion to silicon is excellent at temperatures of 350 0 C and above. Selective W using SiH 4 reduction for doped silicon contact fill shows none of the consumption or encroachment problems common to H 2 reduction, although selectivity is more sensitive. Contact resistance for p + and n + silicon contacts are comparable to aluminum controls and to previously published data. Blanket deposition into narrow geometries gives ≥0% step coverage and without keyholes in the 250--450 0 C deposition temperature range. For low-SiH 4 flows, deposition at 500 0 C causes small keyholes, while at 550 0 C even larger keyholes result. At higher SiH 4 flows, keyholes are typically not seen from 250 to 550 0 C

Characterization of duplex stainless steel weld metals obtained by hybrid plasma-gas metal arc welding

Directory of Open Access Journals (Sweden)

Koray Yurtisik

2013-09-01

Full Text Available Despite its high efficiency, autogenous keyhole welding is not well-accepted for duplex stainless steels because it causes excessive ferrite in as-welded duplex microstructure, which leads to a degradation in toughness and corrosion properties of the material. Combining the deep penetration characteristics of plasma arc welding in keyhole mode and metal deposition capability of gas metal arc welding, hybrid plasma - gas metal arc welding process has considered for providing a proper duplex microstructure without compromising the welding efficiency. 11.1 mm-thick standard duplex stainless steel plates were joined in a single-pass using this novel technique. Same plates were also subjected to conventional gas metal arc and plasma arc welding processes, providing benchmarks for the investigation of the weldability of the material. In the first place, the hybrid welding process enabled us to achieve less heat input compared to gas metal arc welding. Consequently, the precipitation of secondary phases, which are known to be detrimental to the toughness and corrosion resistance of duplex stainless steels, was significantly suppressed in both fusion and heat affected zones. Secondly, contrary to other keyhole techniques, proper cooling time and weld metal chemistry were achieved during the process, facilitating sufficient reconstructive transformation of austenite in the ferrite phase.

The impact of price reductions on individuals' choice of healthy meals away from home.

Science.gov (United States)

Nordström, Jonas; Thunström, Linda

2015-06-01

Food high in energy but low in nutritional value is an important contributor to several serious illnesses, and one type of food that is particularly high in energy but low in nutrition is food consumed away from home. In this paper, we examine the demand and willingness to pay for healthy, Keyhole-labelled meals. A Keyhole-labelled meal is particularly low in energy, fat, sugar and salt, but particularly high in fibre. The results suggest that to get the majority of individuals to choose the healthy option regularly it would be necessary to alter the relative price between healthy and less healthy meals. Generally groups of individuals with a poor nutritional intake require a larger compensation (subsidy) before they choose the healthy alternative. About one third of respondents would choose the healthy option regularly if the prices for a healthy and less healthy meal were the same. In particular groups of individuals who already have a relatively good nutritional intake would select the healthy option. Groups with a generally poor nutritional intake (men and individuals with lower education and lower income) would gain health benefits from a subsidy of Keyhole-labelled meals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Laser beam-plasma plume interaction during laser welding

Science.gov (United States)

Hoffman, Jacek; Moscicki, Tomasz; Szymanski, Zygmunt

2003-10-01

Laser welding process is unstable because the keyhole wall performs oscillations which results in the oscillations of plasma plume over the keyhole mouth. The characteristic frequencies are equal to 0.5-4 kHz. Since plasma plume absorbs and refracts laser radiation, plasma oscillations modulate the laser beam before it reaches the workpiece. In this work temporary electron densities and temperatures are determined in the peaks of plasma bursts during welding with a continuous wave CO2 laser. It has been found that during strong bursts the plasma plume over the keyhole consists of metal vapour only, being not diluted by the shielding gas. As expected the values of electron density are about two times higher in peaks than their time-averaged values. Since the plasma absorption coefficient scales as ~N2e/T3/2 (for CO2 laser radiation) the results show that the power of the laser beam reaching the metal surface is modulated by the plasma plume oscillations. The attenuation factor equals 4-6% of the laser power but it is expected that it is doubled by the refraction effect. The results, together with the analysis of the colour pictures from streak camera, allow also interpretation of the dynamics of the plasma plume.

[Giant intradiploic infratentorial epidermoid cyst].

Science.gov (United States)

Alberione, F; Caire, F; Fischer-Lokou, D; Gueye, M; Moreau, J J

2007-10-01

Epidermoid cysts are benign, uncommon lesions (1% of all intracranial tumors). Their localization is intradiploic in 25% of cases, and exceptionally subtentorial. We report here a rare case of giant intradiploic infratentorial epidermoid cyst. A 74-year old patient presented with recent diplopia and sindrome cerebellar. CT scan and MR imaging revealed a giant osteolytic extradural lesion of the posterior fossa (5.2 cm x 3.8 cm) with a small area of peripheral enhancement after contrast injection. Retrosigmoid suboccipital craniectomy allowed a satisfactory removal of the tumor, followed by an acrylic cranioplasty. The outcome was good. Neuropathological examination confirmed an epidermoid cyst. We review the literature and discuss our case.

Pontine extension of a tentorial schwannoma without cranial nerve involvement: a case report

Directory of Open Access Journals (Sweden)

D'Urso Pietro

2011-12-01

Full Text Available Abstract Introduction Intracranial schwannomas unrelated to the cranial nerves are uncommon. We report a new case of tentorial schwannoma unrelated to the cranial nerves, with extension into the pons. A literature review with discussion of the most relevant pathogenetic aspects is also performed. Case presentation A 42-year-old Caucasian man was admitted with right-sided paresthesias and weakness of his upper and lower extremities. The neurological examination revealed right hemiparesis and hemi-hypoesthesia. A brain magnetic resonance imaging scan revealed a cerebellopontine lesion, arising from the left free edge of the tentorium, and extending into his pons. A piecemeal removal was performed through a retrosigmoid approach. The lesion was not found to be associated with any cranial nerves. The histological examination revealed a schwannoma Antoni type A. His postoperative course was uneventful. At one year follow-up, the patient was neurologically intact and the magnetic resonance imaging of his brain performed at that time showed complete removal without signs of recurrence. Conclusion Tentorial schwannomas are rare clinical entities. Knowledge of their clinical, radiological and anatomical characteristics is very important for the correct diagnosis and management.

Awake craniotomy for assisting placement of auditory brainstem implant in NF2 patients.

Science.gov (United States)

Zhou, Qiangyi; Yang, Zhijun; Wang, Zhenmin; Wang, Bo; Wang, Xingchao; Zhao, Chi; Zhang, Shun; Wu, Tao; Li, Peng; Li, Shiwei; Zhao, Fu; Liu, Pinan

2018-06-01

Auditory brainstem implants (ABIs) may be the only opportunity for patients with NF2 to regain some sense of hearing sensation. However, only a very small number of individuals achieved open-set speech understanding and high sentence scores. Suboptimal placement of the ABI electrode array over the cochlear nucleus may be one of main factors for poor auditory performance. In the current study, we present a method of awake craniotomy to assist with ABI placement. Awake surgery and hearing test via the retrosigmoid approach were performed for vestibular schwannoma resections and auditory brainstem implantations in four patients with NF2. Auditory outcomes and complications were assessed postoperatively. Three of 4 patients who underwent awake craniotomy during ABI surgery received reproducible auditory sensations intraoperatively. Satisfactory numbers of effective electrodes, threshold levels and distinct pitches were achieved in the wake-up hearing test. In addition, relatively few electrodes produced non-auditory percepts. There was no serious complication attributable to the ABI or awake craniotomy. It is safe and well tolerated for neurofibromatosis type 2 (NF2) patients using awake craniotomy during auditory brainstem implantation. This method can potentially improve the localization accuracy of the cochlear nucleus during surgery.

Prospective Study of Neuroendoscopy versus Microscopy: 213 Cases of Microvascular Decompression for Trigeminal Neuralgia Performed by One Neurosurgeon.

Science.gov (United States)

Xiang, Hui; Wu, Guangyong; Ouyang, Jia; Liu, Ruen

2018-03-01

To compare the efficacy and complications of microvascular decompression (MVD) by complete neuroendoscopy versus microscopy for 213 cases of trigeminal neuralgia (TN). Between January 2014 and January 2016, 213 patients with TN were randomly assigned to the neuroendoscopy (n = 105) or microscopy (n = 114) group for MVD via the suboccipital retrosigmoid approach. All procedures were performed by the same neurosurgeon. Follow-up was conducted by telephone interview. Statistical data were analyzed with the chi-square test, and a probability (P) value of ≤0.05 was considered statistically significant. Chi-square test was conducted using SAS 9.4 software (SAS Institute, Cary, North Carolina, USA). There were no statistical differences between the 2 groups in pain-free condition immediately post procedure, pain-free condition 1 year post procedure, hearing loss, facial hypoesthesia, transient ataxia, aseptic meningitis, intracranial infections, and herpetic lesions of the lips. There were no instances of death, facial paralysis, cerebral hemorrhage, or cerebrospinal fluid leakage in either group. There were no significant differences in the cure rates or incidences of surgical complications between neuroendoscopic and microscopic MVD. Copyright © 2017 Elsevier Inc. All rights reserved.

Active Bone Conduction Prosthesis: BonebridgeTM

Directory of Open Access Journals (Sweden)

Zernotti, Mario E.

2015-10-01

Full Text Available Introduction Bone conduction implants are indicated for patients with conductive and mixed hearing loss, as well as for patients with single-sided deafness (SSD. The transcutaneous technology avoids several complications of the percutaneous bone conduction implants including skin reaction, skin growth over the abutment, and wound infection. The Bonebridge (MED-EL, Austria prosthesis is a semi-implantable hearing system: the BCI (Bone Conduction Implant is the implantable part that contains the Bone Conduction-Floating Mass Transducer (BC-FMT, which applies the vibrations directly to the bone; the external component is the audio processor Amadé BB (MED-EL, Austria, which digitally processes the sound and sends the information through the coil to the internal part. Bonebridge may be implanted through three different approaches: the transmastoid, the retrosigmoid, or the middle fossa approach. Objective This systematic review aims to describe the world́s first active bone conduction implant system, Bonebridge, as well as describe the surgical techniques in the three possible approaches, showing results from implant centers in the world in terms of functional gain, speech reception thresholds and word recognition scores. Data Synthesis The authors searched the MEDLINE database using the key term Bonebridge. They selected only five publications to include in this systematic review. The review analyzes 20 patients that received Bonebridge implants with different approaches and pathologies. Conclusion Bonebridge is a solution for patients with conductive/mixed hearing loss and SSD with different surgical approaches, depending on their anatomy. The system imparts fewer complications than percutaneous bone conduction implants and shows proven benefits in speech discrimination and functional gain.

Evaluating the Impact of Conservatism in Industrial Fatigue Analysis of Life-Limited Components

Directory of Open Access Journals (Sweden)

Hoole Joshua

2018-01-01

Full Text Available This paper presents a review of the conservatism approaches applied by different industrial sectors to the stress-life (S-N analysis of ‘life-limited’ or ‘safe-life’ components. A comparison of the fatigue design standards for 6 industrial sectors identified that the conservatism approaches are highly inconsistent when comparing the areas of variability and uncertainty accounted for along with the conservatism magnitude and method of application. Through the use of a case-study based on the SAE keyhole benchmark and 4340 steel S-N data, the industrial sector which introduces the greatest reduction of a component life-limit was identified as the nuclear sector. The results of the case-study also highlighted that conservatism applied to account for scatter in S-N data currently provides the greatest contribution to the reduction of component life-limits.

Numerical model of the plasma formation at electron beam welding

Energy Technology Data Exchange (ETDEWEB)

Trushnikov, D. N., E-mail: trdimitr@yandex.ru [The Department for Applied Physics, Perm National Research Polytechnic University, Perm 614990 (Russian Federation); The Department for Welding Production and Technology of Constructional Materials, Perm National Research Polytechnic University, Perm 614990 (Russian Federation); Mladenov, G. M., E-mail: gmmladenov@abv.bg [Institute of Electronics, Bulgarian Academy of Sciences, 72 Tzarigradsko Shose, 1784 Sofia (Bulgaria); Technology Centre of Electron Beam and Plasma Technologies and Techniques, 68-70 Vrania, ap.10, Banishora, 1309 Sofia (Bulgaria)

2015-01-07

The model of plasma formation in the keyhole in liquid metal as well as above the electron beam welding zone is described. The model is based on solution of two equations for the density of electrons and the mean electron energy. The mass transfer of heavy plasma particles (neutral atoms, excited atoms, and ions) is taken into account in the analysis by the diffusion equation for a multicomponent mixture. The electrostatic field is calculated using the Poisson equation. Thermionic electron emission is calculated for the keyhole wall. The ionization intensity of the vapors due to beam electrons and high-energy secondary and backscattered electrons is calibrated using the plasma parameters when there is no polarized collector electrode above the welding zone. The calculated data are in good agreement with experimental data. Results for the plasma parameters for excitation of a non-independent discharge are given. It is shown that there is a need to take into account the effect of a strong electric field near the keyhole walls on electron emission (the Schottky effect) in the calculation of the current for a non-independent discharge (hot cathode gas discharge). The calculated electron drift velocities are much bigger than the velocity at which current instabilities arise. This confirms the hypothesis for ion-acoustic instabilities, observed experimentally in previous research.

Modelling of fluid flow phenomenon in laser+GMAW hybrid welding of aluminum alloy considering three phase coupling and arc plasma shear stress

Science.gov (United States)

Xu, Guoxiang; Li, Pengfei; Cao, Qingnan; Hu, Qingxian; Gu, Xiaoyan; Du, Baoshuai

2018-03-01

The present study aims to develop a unified three dimensional numerical model for fiber laser+GMAW hybrid welding, which is used to study the fluid flow phenomena in hybrid welding of aluminum alloy and the influence of laser power on weld pool dynamic behavior. This model takes into account the coupling of gas, liquid and metal phases. Laser heat input is described using a cone heat source model with changing peak power density, its height being determined based on the keyhole size. Arc heat input is modeled as a double ellipsoid heat source. The arc plasma flow and droplet transfer are simulated through the two simplified models. The temperature and velocity fields for different laser powers are calculated. The computed results are in general agreement with the experimental data. Both the peak and average values of fluid flow velocity during hybrid welding are much higher than those of GMAW. At a low level of laser power, both the arc force and droplet impingement force play a relatively large role on fluid flow in the hybrid welding. Keyhole depth always oscillates within a range. With an increase in laser power, the weld pool behavior becomes more complex. An anti-clockwise vortex is generated and the stability of keyhole depth is improved. Besides, the effects of laser power on different driving forces of fluid flow in weld pool are also discussed.

46 CFR 54.05-5 - Toughness test specimens.

Science.gov (United States)

2010-10-01

... shown in Figure 4 of the specification. Special attention is drawn to the fact that the Charpy Keyhole....090-inch. In preparing weld specimens for dropweight testing, weld reinforcement shall be ground flush...

Closed Loop Control of Penetration Depth during CO₂ Laser Lap Welding Processes

Directory of Open Access Journals (Sweden)

Antonio Ancona

2012-08-01

Full Text Available In this paper we describe a novel spectroscopic closed loop control system capable of stabilizing the penetration depth during laser welding processes by controlling the laser power. Our novel approach is to analyze the optical emission from the laser generated plasma plume above the keyhole, to calculate its electron temperature as a process-monitoring signal. Laser power has been controlled by using a quantitative relationship between the penetration depth and the plasma electron temperature. The sensor is able to correlate in real time the difference between the measured electron temperature and its reference value for the requested penetration depth. Accordingly the closed loop system adjusts the power, thus maintaining the penetration depth.

Heart bypass surgery - minimally invasive - discharge

Science.gov (United States)

... invasive direct coronary artery bypass - discharge; MIDCAB - discharge; Robot assisted coronary artery bypass - discharge; RACAB - discharge; Keyhole ... M. is also a founding member of Hi-Ethics and subscribes to the principles of the Health ...

[Pneumocephalus as a cause of a decrease in the bispectral index].

Science.gov (United States)

Herreras Gutiérrez, J L; Gilsanz Rodríguez, F

2014-01-01

A sharp decrease in the values of the bispectral index (BIS), along with an increase in suppression rate, was observed in a patient after the removal of an epidermoid tumor in the cerebellopontine angle by right retrosigmoid access under general anesthesia. This was probably related to a frontal pneumocephalus. No accompanying neurological signs were observed. The patient was extubated in the Recovery Room with no further incidents, as the BIS increased again. The neurosurgeons chose conservative treatment, relying on the reabsorption and redistribution of the air. Copyright © 2012 Sociedad Española de Anestesiología, Reanimación y Terapéutica del Dolor. Published by Elsevier España. All rights reserved.

Lateral Transorbital Endoscopic Access to the Hippocampus, Amygdala, and Entorhinal Cortex: Initial Clinical Experience.

Science.gov (United States)

Chen, H Isaac; Bohman, Leif-Erik; Emery, Lyndsey; Martinez-Lage, Maria; Richardson, Andrew G; Davis, Kathryn A; Pollard, John R; Litt, Brian; Gausas, Roberta E; Lucas, Timothy H

2015-01-01

Transorbital approaches traditionally have focused on skull base and cavernous sinus lesions medial to the globe. Lateral orbital approaches to the temporal lobe have not been widely explored despite several theoretical advantages compared to open craniotomy. Recently, we demonstrated the feasibility of the lateral transorbital technique in cadaveric specimens with endoscopic visualization. We describe our initial clinical experience with the endoscope-assisted lateral transorbital approach to lesions in the temporal lobe. Two patients with mesial temporal lobe pathology presenting with seizures underwent surgery. The use of a transpalpebral or Stallard-Wright eyebrow incision enabled access to the intraorbital compartment, and a lateral orbital wall 'keyhole' opening permitted visualization of the anterior temporal pole. This approach afforded adequate access to the surgical target and surrounding structures and was well tolerated by the patients. To the best of our knowledge, this report constitutes the first case series describing the endoscope-assisted lateral transorbital approach to the temporal lobe. We discuss the limits of exposure, the nuances of opening and closing, and comparisons to open craniotomy. Further prospective investigation of this approach is warranted for comparison to traditional approaches to the mesial temporal lobe. © 2015 S. Karger AG, Basel.

Analysis of Welding Zinc Coated Steel Sheets in Zero Gap Configuration by 3D Simulations and High Speed Imaging

Science.gov (United States)

Koch, Holger; Kägeler, Christian; Otto, Andreas; Schmidt, Michael

Welding of zinc coated sheets in zero gap configuration is of eminent interest for the automotive industry. This Laser welding process would enable the automotive industry to build auto bodies with a high durability in a plain manufacturing process. Today good welding results can only be achieved by expensive constructive procedures such as clamping devices to ensure a defined gad. The welding in zero gap configuration is a big challenge because of the vaporised zinc expelled from the interface between the two sheets. To find appropriate welding parameters for influencing the keyhole and melt pool dynamics, a three dimensional simulation and a high speed imaging system for laser keyhole welding have been developed. The obtained results help to understand the process of the melt pool perturbation caused by vaporised zinc.

Modeling of plasma plume induced during laser welding

International Nuclear Information System (INIS)

Moscicki, T.; Hoffman, J.; Szymanski, Z.

2005-01-01

During laser welding, the interaction of intense laser radiation with a work-piece leads to the formation of a long, thin, cylindrical cavity in a metal, called a keyhole. Generation of a keyhole enables the laser beam to penetrate into the work-piece and is essential for deep welding. The keyhole contains ionized metal vapour and is surrounded by molten material called the weld pool. The metal vapour, which flows from the keyhole mixes with the shielding gas flowing from the opposite direction and forms a plasma plume over the keyhole mouth. The plasma plume has considerable influence on the processing conditions. Plasma strongly absorbs laser radiation and significantly changes energy transfer from the laser beam to a material. In this paper the results of theoretical modelling of plasma plume induced during welding with CO 2 laser are presented. The set of equations consists of equation of conservation of mass, energy, momentum and the diffusion equation: ∂ρ/∂t + ∇·(ρ ρ ν =0; ∂(ρE)/∂t + ∇·( ρ ν (ρE + p)) = ∇ (k eff ∇T - Σ j h j ρ J j + (τ eff · ρ ν )) + Σ i κ i I i - R; ∂/∂t(ρ ρ ν ) + ∇· (ρ ρ ν ρ ν ) = - ∇p + ∇(τ) + ρ ρ g + ρ F, where τ is viscous tensor τ = μ[(∇ ρ ν + ∇ ρT ν )-2/3∇· ρ ν I]; ∂/∂t(ρY i ) + ∇·(ρ ρ ν Y i ) = ∇·ρD i,m ∇T i ; where μ ν denotes velocity vector, E - energy, ρ mass density; k - thermal conductivity, T- temperature, κ - absorption coefficient, I i local laser intensity, R - radiation loss function, p - pressure, h j enthalpy, J j - diffusion flux of j component, ν g - gravity, μ F - external force, μ - dynamic viscosity, I - unit tensor, Y i - mass fraction of iron vapor in the gas mixture, D i,m - mass diffusion coefficient. The terms k eff and τ eff contain the turbulent component of the thermal conductivity and the viscosity, respectively. All the material functions are functions of the temperature and mass fraction only. The equations

On the development of an apatitic calcium phosphate bone cement

Indian Academy of Sciences (India)

Unknown

phosphorous based ingredients in powder form, which on mixing with an aqueous ... repair procedures from major surgery to a key-hole opera- tion. The investigation in ... which satisfy the biocompatibility requirements was selec- ted as the ...

Study of dimensionless quantities to analyse front and rear wall of ...

Indian Academy of Sciences (India)

hydrodynamic quantities describe the mechanism behind flow pattern present in .... beam is focused into a small spot adjustable approximately 0.1 to 0.8 mm in ... moves, the liquefied metal around the 'keyhole' flows back in, solidifying and.

Throughput and Delay Analysis of HARQ with Code Combining over Double Rayleigh Fading Channels

KAUST Repository

Chelli, Ali; Zedini, Emna; Alouini, Mohamed-Slim; Patzold, Matthias Uwe; Balasingham, Ilangko

2018-01-01

-to-vehicle communication systems as well as amplify-and-forward relaying and keyhole channels. This work studies the performance of HARQ-CC over double Rayleigh channels from an information theoretic perspective. Analytical approximations are derived for the

Surgery of petroclival meningiomas. Recent surgical results and outcomes

Directory of Open Access Journals (Sweden)

Radoi Mugurel

2015-03-01

Full Text Available Petroclival meningiomas represent only 10% of all meningiomas located in the posterior fossa, but are some of the most formidable challenges in skull base surgery. We described our recent experience (2005-September2014 regarding the surgery of these tumors. We retrospectively analyzed surgical results and outcome in 11 cases of petroclival meningiomas. Most common symptoms in our series were headache and gait disturbance, while cranial nerves palsies represented the most common presenting signs. There were 8 females and 3 males, and the mean age was 52 years. Surgical approaches chosen for petroclival meningiomas in our series were retrosigmoid (9 patients and subtemporal transtentorial (2 patients. We achieved total tumor resection in 5 cases (45% and subtotal resection in 6 cases (55%. Overall outcome (total/subtotal resection was good in 6 cases, fair in 3 cases and poor in one case. One postoperative death occurred due to hemorrhagic midbrain infarction (9%. Complications were usually related to cranial nerve deficits: loss of hearing (2 patients, paresis of trochlear nerve (1 patient, trigeminal nerve (3 patients and facial nerve (1 patient. In 4 patients these cranial nerves deficits were transient. In one case, a patient developed postoperative hydrocephalus and needed shunt placement. Despite the fact that complications can be disastrous, we considered that an appropriate approach, combined with microsurgical techniques and a better understanding of the anatomy, greatly decrease the incidence and severity of complications and make feasible a total tumor resection.

A Rare Case of Radiologically Not Distinguishable Coexistent Meningioma and Vestibular Schwannoma in the Cerebellopontine Angle – Case Report and Literature Review

Directory of Open Access Journals (Sweden)

Juergen Grauvogel

2010-08-01

Full Text Available Background: The simultaneous occurrence of cerebellopontine angle (CPA meningioma and vestibular schwannoma (VS in the absence of neurofibromatosis type 2 or history of irradiation is very rare. We report a case with coexistent CPA meningioma and VS, which were radiologically not distinguishable in preoperative imaging. Case Description: A 46-year-old female presented with acute hearing loss, tinnitus and gait ataxia. Otorhinolaryngological diagnostic workup and imaging studies showed an intra- and extrameatal homogenous contrast enhancing lesion. The neuroradiological diagnosis was VS. The patient was operated via the retrosigmoid approach. Intraoperatively two distinct tumors were found: a small, mainly intrameatally located VS and a larger meningioma originating from the dura of the petrous bone. Both tumors were completely microsurgically removed. The patient experienced no new neurological deficit after surgery; particularly facial nerve function was completely preserved. Histopathological examination revealed a fibromatous meningioma and a VS, respectively. Conclusions: The coincidental occurrence of CPA meningioma and VS is very rare. Careful interpretation of imaging studies before surgery is crucial. Even such rare cases should be kept in mind when discussing the therapeutic options with the patient. More studies are needed for a better understanding of mechanisms leading to multiple tumor growth.

Adoptive transfer of natural antibodies to non-immunized chickens affects subsequent antigen-specific humoral and cellular immune responses

NARCIS (Netherlands)

Lammers, A.; Klomp, M.E.V.; Nieuwland, M.G.B.; Savelkoul, H.F.J.; Parmentier, H.K.

2004-01-01

To determine a regulatory function of natural antibodies in the immune response of chickens, pooled plasma obtained from non-immunized (naive) 15 months old hens was subjected to keyhole limpet hemocyanin (KLH) antigen-affinity chromatography. Purified KLH-binding antibodies were adoptively

Sõja neljas päev: paigalseis Eufrati joonel

Index Scriptorium Estoniae

2003-01-01

Sõjategevust Iraagis kajastav Iraagi ja Bagdadi kaart. KH-11 Keyhole luuresatelliit. Skeem: USA katse tappa Saddam avalöögiga. B-52 raskepommitaja hävitusjõud. Skeem: USA Patriot-rakett tulistas alla Briti sõjalennuki. Patriot - õhutõrjesüsteem

XML: Ejemplos de uso (presentación)

OpenAIRE

Luján Mora, Sergio

2011-01-01

XML (eXtensible Markup Language, Lenguaje de marcas extensible) - Aplicación XML = Lenguaje de marcado = Vocabulario - Ejemplos: DocBook, Chemical Markup Language, Keyhole Markup Language, Mathematical Markup Language, Open Document, Open XML Format, Scalable Vector Graphics, Systems Byology Markup Language.

XML: Ejemplos de uso

OpenAIRE

Luján Mora, Sergio

2011-01-01

XML (eXtensible Markup Language, Lenguaje de marcas extensible) - Aplicación XML = Lenguaje de marcado = Vocabulario - Ejemplos: DocBook, Chemical Markup Language, Keyhole Markup Language, Mathematical Markup Language, Open Document, Open XML Format, Scalable Vector Graphics, Systems Byology Markup Language.

Development of a novel and automated fluorescent immunoassay for the analysis of beta-lactam antibiotics

NARCIS (Netherlands)

Benito-Pena, E.; Moreno-Bondi, M.C.; Orellana, G.; Maquieira, K.; Amerongen, van A.

2005-01-01

An automated immunosensor for the rapid and sensitive analysis of penicillin type -lactam antibiotics has been developed and optimized. An immunogen was prepared by coupling the common structure of the penicillanic -lactam antibiotics, i.e., 6-aminopenicillanic acid to keyhole limpet hemocyanin.

Military Operating Room of the Future

Science.gov (United States)

2012-10-01

2006). Analyses of these events demonstrate the close coupling between task, team and technology for the management of safe, effective cardiac...This growing field of surgical endeavor has distinct advantages in offering keyhole (laparoscopic) surgery with a greater range of articulation than

Heart bypass surgery - minimally invasive

Science.gov (United States)

... MIDCAB; Robot-assisted coronary artery bypass; RACAB; Keyhole heart surgery; CAD - MIDCAB; Coronary artery disease - MIDCAB ... To perform this surgery: The heart surgeon will make a 3- to 5-inch (8 to 13 centimeters) surgical cut in the left part of your chest ...

Assessment of immunotoxic effects of environmental contamination using a cotton rat model

International Nuclear Information System (INIS)

Zhang, Z.R.; Propst, T.L.; McMurry, S.T.; Lochmiller, R.L.; McBee, K.; Quails, C.W. Jr.; Burks, S.L.

1993-01-01

Adult National Institute of Health inbred cotton rats (Sigmodon hispidus) were housed in six terrestrial mesocosms on or near an abandoned oil refinery in central Oklahoma for 56 days. Exposure sites included three mesocosms located on sites judged to be contaminated with a variety of complex mixtures of contaminants and three matched reference mesocosm. In addition, wild cotton rats were collected from contaminated and reference areas near the mesocosm sites. Peripheral leukocyte and erythrocyte variables, secondary lymphoid organ weight and cellularity, proliferative response of splenocytes to mitogens, lymphocyte subpopulations, delayed-type hypersensitivity response, 24 h hypersensitivity, antibody response to keyhole limpet hemocyanin, NK cell activity, macrophage metabolic functions, and complement activity were measures as a comprehensive screen of immunocompetence. According to current data analysis, peripheral leukocyte numbers, mitogenic response of splenocytes, antibody response to keyhole limpet hemocyanin, delayed-type sensitivity and 24 h hypersensitivity were altered by contaminant exposure

[INVITED] Evaluation of process observation features for laser metal welding

Science.gov (United States)

Tenner, Felix; Klämpfl, Florian; Nagulin, Konstantin Yu.; Schmidt, Michael

2016-06-01

In the present study we show how fast the fluid dynamics change when changing the laser power for different feed rates during laser metal welding. By the use of two high-speed cameras and a data acquisition system we conclude how fast we have to image the process to measure the fluid dynamics with a very high certainty. Our experiments show that not all process features which can be measured during laser welding do represent the process behavior similarly well. Despite the good visibility of the vapor plume the monitoring of its movement is less suitable as an input signal for a closed-loop control. The features measured inside the keyhole show a good correlation with changes of process parameters. Due to its low noise, the area of the keyhole opening is well suited as an input signal for a closed-loop control of the process.

Object detection by correlation coefficients using azimuthally averaged reference projections.

Science.gov (United States)

Nicholson, William V

2004-11-01

A method of computing correlation coefficients for object detection that takes advantage of using azimuthally averaged reference projections is described and compared with two alternative methods-computing a cross-correlation function or a local correlation coefficient versus the azimuthally averaged reference projections. Two examples of an application from structural biology involving the detection of projection views of biological macromolecules in electron micrographs are discussed. It is found that a novel approach to computing a local correlation coefficient versus azimuthally averaged reference projections, using a rotational correlation coefficient, outperforms using a cross-correlation function and a local correlation coefficient in object detection from simulated images with a range of levels of simulated additive noise. The three approaches perform similarly in detecting macromolecular views in electron microscope images of a globular macrolecular complex (the ribosome). The rotational correlation coefficient outperforms the other methods in detection of keyhole limpet hemocyanin macromolecular views in electron micrographs.

76 FR 59559 - Facilitating the Use of Microwave for Wireless Backhaul and Other Uses and Providing Additional...

Science.gov (United States)

2011-09-27

...'' links. The idea had its origin in a petition filed by Wireless Strategies, Inc. (WSI) asking the... radiates energy outward in a keyhole-shaped signal pattern. This signal pattern precludes other stations... of backhaul, telecommunications support for small intelligent data centers, and rural telemedicine...

Correlated effects of selection for immunity in White Leghorn chicken lines on natural antibodies and specific antibody responses to KLH and M. butyricum

NARCIS (Netherlands)

Minozzi, G.; Parmentier, H.K.; Mignon-Grasteau, S.; Nieuwland, M.G.B.; Bed'hom, B.; Gourichon, D.; Minvielle, F.; Pinard-van der Laan, M.H.

2008-01-01

Background - The effect of selection for three general immune response traits on primary antibody responses (Ab) to Mycobacterium butyricum or keyhole limpet hemocyanin (KLH) was studied in four experimental lines of White Leghorn chicken. Birds underwent 12 generations of selection for one of three

Cornerstone: Foundational Models and Services for Integrated Battle Planning

Science.gov (United States)

2012-06-01

We close with a summary of future planned research. 3 Cross-Domain Knowledge Representation One of the primary reasons behind the...mission data using Google Earth to display the results of a Keyhole Markup Language (KML) mission data translator. Finally, we successfully ran Thread 1

KML (Keyhole Markup Language) : a key tool in the education of geo-resources.

Science.gov (United States)

Veltz, Isabelle

2015-04-01

Although going on the ground with pupils remains the best way to understand the geologic structure of a deposit, it is very difficult to bring them in a mining extraction site and it is impossible to explore whole regions in search of these resources. For those reasons the KML (with the Google earth interface) is a very complete tool for teaching geosciences. Simple and intuitive, its handling is quickly mastered by the pupils, it also allows the teachers to validate skills for IT certificates. It allows the use of KML files stemming from online banks, from personal productions of the teacher or from pupils' works. These tools offer a global approach in 3D as well as a geolocation-based access to any type of geological data. The resource on which I built this KML is taught in the curriculum of the 3 years of French high school, it is methane hydrate. This non conventional hydrocarbon molecule enters in this vague border between mineral an organic matter (as phosphate deposits). It has become for over ten year the subject of the race for the exploitation of the gas hydrates fields in order to try to supply to the world demand. The methane hydrate fields are very useful and interesting to study the 3 majors themes of geological resource: the exploration, the exploitation and the risks especially for environments and populations. The KML which I propose allows the pupils to put itself in the skin of a geologist in search of deposits or on the technician who is going to extract the resource. It also allows them to evaluate the risks connected to the effect of tectonics activity or climatic changes on the natural or catastrophic releasing of methane and its role in the increase of the greenhouse effect. This KML associated to plenty of pedagogic activities is directly downloadable for teachers at http://eduterre.ens-lyon.fr/eduterre-usages/actualites/methane/.

Laser beam welding of titanium additive manufactured parts

NARCIS (Netherlands)

Wits, Wessel Willems; Jauregui Becker, Juan Manuel

2015-01-01

In this paper the joinability of titanium Additive Manufactured (AM) parts is explored. Keyhole welding, using a pulsed laser beam, of conventionally produced parts is compared to AM parts. Metal AM parts are notorious for having remaining porosities and other non-isotropic properties due to the

A Google Earth Grand Tour of the Terrestrial Planets

Science.gov (United States)

De Paor, Declan; Coba, Filis; Burgin, Stephen

2016-01-01

Google Earth is a powerful instructional resource for geoscience education. We have extended the virtual globe to include all terrestrial planets. Downloadable Keyhole Markup Language (KML) files (Google Earth's scripting language) associated with this paper include lessons about Mercury, Venus, the Moon, and Mars. We created "grand…

Spectral analysis of the process emission during laser welding of AISI 304 stainless steel with disk and Nd:YAG laser

NARCIS (Netherlands)

Konuk, A.R.; Aarts, R.G.K.M.; Huis in 't Veld, A.J.

2009-01-01

Optical emissions from the laser welding process can be obtained relatively easy in real-time. Such emissions come from the melt pool, keyhole, or plume during welding. Therefore it is very beneficial to establish a clear relation between characteristics of these emissions and the resulting weld

Changes of structure and properties in the heat-affected zone during the welding of high-strength aluminium alloys. Gefuege- und Eigenschaftsaenderungen in der Waermeeinflusszone beim Schweissen hochfester Aluminiumlegierungen

Energy Technology Data Exchange (ETDEWEB)

Umgeher, A. (Tyrolitschleifmittelwerke Swarovski KG, Schwaz (Austria)); Cerjak, H. (Technische Univ., Graz (Austria))

High strength aluminium alloys like AlZnMgCu 1.5 are usually classified as 'non-weldable' alloys. If welding technologies such as TIG-plasma keyhole welding are used, it is possible to weld these alloys successfully. However, the heat input during welding affects the base material adjacent to the fusion zone. The main objective of this investigation was to study the change of microstructure and properties in this heat affected zone (HAZ) of high strength aluminium alloys. The base material was a high strength wrought aluminium alloy AlZnMgCu 1.5 (7075) in the T6 condition. The specimens were welded by TIG-plasma keyhole welding. Additionally, Gleeble welding simulation techniques were used. The specimens were investigated in the 'as welded' condition, 'naturally aged', 'artificially aged', and after a complete post weld heat treatment. The microstructure was investigated using light and electron microscopy. Hardness and electric resistivity measurements and DSC-analysis were made. (orig.)

Mechanical Property Analysis in the Retracted Pin-Tool (RPT) Region of Friction Stir Welded (FSW) Aluminum Lithium 2195

Science.gov (United States)

Ding, R. Jeffrey; Oelgoetz, Peter A.

1999-01-01

The "Auto-Adjustable Pin Tool for Friction Stir Welding", was developed at The Marshall Space Flight Center to address process deficiencies unique to the FSW process. The auto-adjustable pin tool, also called the retractable pin-tool (R.PT) automatically withdraws the welding probe of the pin-tool into the pin-tool's shoulder. The primary function of the auto-adjustable pin-tool is to allow for keyhole closeout, necessary for circumferential welding and localized weld repair, and, automated pin-length adjustment for the welding of tapered material thickness. An overview of the RPT hardware is presented. The paper follows with studies conducted using the RPT. The RPT was used to simulate two capabilities; welding tapered material thickness and closing out the keyhole in a circumferential weld. The retracted pin-tool regions in aluminum- lithium 2195 friction stir weldments were studied through mechanical property testing and metallurgical sectioning. Correlation's can be =de between retractable pin-tool programmed parameters, process parameters, microstructure, and resulting weld quality.

Curative analysis of different surgical treatments for non-solid hemangioblastoma in posterior cranial fossa

Directory of Open Access Journals (Sweden)

Yu-xiang MA

2015-07-01

Full Text Available Objective  The article analyzed the curative effect of different surgical treatments for non-solid hemangioblastoma in posterior cranial fossa to explore reasonable operation method.  Methods  Clinical data of 61 patients with non-solid hemangioblastoma who underwent surgeries in Tianjin Huanhu Hospital during July 2007 and June 2014 were retrospectively analyzed. According to surgical approaches and the situation of foramen magnum and atlas, these patients were divided into 5 groups: midline approach opening foramen magnum and atlas (Group A, midline approach without opening foramen magnum and atlas (Group B, paramedian approach opening foramen magnum and atlas (Group C, paramedian approach without opening foramen magnum and atlas (Group D, retrosigmoid approach (Group E. By collecting clinical symptoms, imaging findings, surgical records and postoperative complications, the surgical results and occurrence of postoperative complications were summarized and reasonable operation method was discussed.  Results  Among 61 patients, total resection was achieved in 56 cases (91.80%, and partial resection was achieved in 5 cases (8.20% . The postoperative remission rate of 43 cases with hydrocephalus was 79.07% (34/43. Intracranial infection was the most common postoperative complication, accounting for 22.95% (14/61. There was significant difference in occurrence rate of intracranial infection among 4 subgroups: opening or not opening the foramen magnum and atlas with or without restoring bone flap (Z = 16.269, P = 0.001. In the subgroup of not opening foramen magnum and atlas with restoring bone flap, the infection rate, which accounted for 6.90% (2/29, was the lowest.  Conclusions  The surgical treatment options for non-solid hemangioblastoma in posterior fossa should be done according to patients' condition, and performed by a professional group. If conditions allow, not to open the foramen magnum and atlas, as well as intraoperative

Current-driven ion-acoustic and potential-relaxation instabilities excited in plasma plume during electron beam welding

Energy Technology Data Exchange (ETDEWEB)

Trushnikov, D. N., E-mail: trdimitr@yandex.ru [The department for Applied Physics, Perm National Research Polytechnic University, Perm, 614990 (Russian Federation); Mladenov, G. M., E-mail: gmmladenov@abv.bg; Koleva, E. G., E-mail: eligeorg@abv.bg [Institute of Electronics, Bulgarian Academy of Sciences, 72 Tzarigradsko Shose, 1784, Sofia (Bulgaria); Technology Centre of Electron Beam and Plasma Technologies and Techniques, 68-70 Vrania, ap.10, Banishora,1309, Sofia (Bulgaria); Belenkiy, V. Ya., E-mail: mtf@pstu.ru; Varushkin, S. V., E-mail: stepan.varushkin@mail.ru [The department for Welding Production and Technology of Constructional Materials, Perm National Research Polytechnic University, Perm, 614990 (Russian Federation)

2014-04-15

Many papers have sought correlations between the parameters of secondary particles generated above the beam/work piece interaction zone, dynamics of processes in the keyhole, and technological processes. Low- and high-frequency oscillations of the current, collected by plasma have been observed above the welding zone during electron beam welding. Low-frequency oscillations of secondary signals are related to capillary instabilities of the keyhole, however; the physical mechanisms responsible for the high-frequency oscillations (>10 kHz) of the collected current are not fully understood. This paper shows that peak frequencies in the spectra of the collected high-frequency signal are dependent on the reciprocal distance between the welding zone and collector electrode. From the relationship between current harmonics frequency and distance of the collector/welding zone, it can be estimated that the draft velocity of electrons or phase velocity of excited waves is about 1600 m/s. The dispersion relation with the properties of ion-acoustic waves is related to electron temperature 10 000 K, ion temperature 2 400 K and plasma density 10{sup 16} m{sup −3}, which is analogues to the parameters of potential-relaxation instabilities, observed in similar conditions. The estimated critical density of the transported current for creating the anomalous resistance state of plasma is of the order of 3 A·m{sup −2}, i.e. 8 mA for a 3–10 cm{sup 2} collector electrode. Thus, it is assumed that the observed high-frequency oscillations of the current collected by the positive collector electrode are caused by relaxation processes in the plasma plume above the welding zone, and not a direct demonstration of oscillations in the keyhole.

Retractable Pin Tools for the Friction Stir Welding Process

Science.gov (United States)

1998-01-01

Two companies have successfully commercialized a specialized welding tool developed at the Marshall Space Flight Center (MSFC). Friction stir welding uses the high rotational speed of a tool and the resulting frictional heat created from contact to crush, 'stir' together, and forge a bond between two metal alloys. It has had a major drawback, reliance on a single-piece pin tool. The pin is slowly plunged into the joint between two materials to be welded and rotated as high speed. At the end of the weld, the single-piece pin tool is retracted and leaves a 'keyhole,' something which is unacceptable when welding cylindrical objects such as drums, pipes and storage tanks. Another drawback is the requirement for different-length pin tools when welding materials of varying thickness. An engineer at the MSFC helped design an automatic retractable pin tool that uses a computer-controlled motor to automatically retract the pin into the shoulder of the tool at the end of the weld, preventing keyholes. This design allows the pin angle and length to be adjusted for changes in material thickness and results in a smooth hole closure at the end of the weld. Benefits of friction stir welding, using the MSFC retractable pin tool technology, include the following: The ability to weld a wide range of alloys, including previously unweldable and composite materials; provision of twice the fatigue resistance of fusion welds and no keyholes; minimization of material distortion; no creation of hazards such as welding fumes, radiation, high voltage, liquid metals, or arcing; automatic retraction of the pin at the end of the weld; and maintaining full penetration of the pin.

American Peptide Symposium Proceedings (13th) Held in Edmonton, Alberta, Canada on June 20-25, 1993. Peptides: Chemistry, Structure and Biology

Science.gov (United States)

1993-06-20

protein . rceloMEIS w-mdeimidobenzol UtMA I,-Nfoer N-hydroxy- SONaY succinimide ester iniraioa units 14CM melanin concentrating luM keyhole limpet MCPSA...cyclic depsipeptide aureobasidin A (1), isolated as a major component from the culture medium of the black yeast Aureobasidium puUukans R 106, exhibits

Intraoperative observation of changes in cochlear nerve action potentials during exposure to electromagnetic fields generated by mobile phones.

Science.gov (United States)

Colletti, Vittorio; Mandalà, Marco; Manganotti, Paolo; Ramat, Stefano; Sacchetto, Luca; Colletti, Liliana

2011-07-01

The rapid spread of devices generating electromagnetic fields (EMF) has raised concerns as to the possible effects of this technology on humans. The auditory system is the neural organ most frequently and directly exposed to electromagnetic activity owing to the daily use of mobile phones. In recent publications, a possible correlation between mobile phone usage and central nervous system tumours has been detected. Very recently a deterioration in otoacoustic emissions and in the auditory middle latency responses after intensive and long-term magnetic field exposure in humans has been demonstrated. To determine with objective observations if exposure to mobile phone EMF affects acoustically evoked cochlear nerve compound action potentials, seven patients suffering from Ménière's disease and undergoing retrosigmoid vestibular neurectomy were exposed to the effects of mobile phone placed over the craniotomy for 5 min. All patients showed a substantial decrease in amplitude and a significant increase in latency of cochlear nerve compound action potentials during the 5 min of exposure to EMF. These changes lasted for a period of around 5 min after exposure. The possibility that EMF can produce relatively long-lasting effects on cochlear nerve conduction is discussed and analysed in light of contrasting previous literature obtained under non-surgical conditions. Limitations of this novel approach, including the effects of the anaesthetics, craniotomy and surgical procedure, are presented in detail.

The impact of price reductions on individuals’ choice of healthy meals away from home

DEFF Research Database (Denmark)

Nordström, Leif Jonas; Thunström, Linda

2015-01-01

Food high in energy but low in nutritional value is an important contributor to several serious illnesses, and one type of food that is particularly high in energy but low in nutrition is food consumed away from home. In this paper, we examine the demand and willingness to pay for healthy, Keyhole...

Surgical management of macroglossia secondary to amyloidosis.

Science.gov (United States)

Gadiwalla, Yusuf; Burnham, Richard; Warfield, Adrian; Praveen, Prav

2016-04-11

The authors report a case of amyloidosis-induced macroglossia treated with surgical reduction of the tongue using a keyhole to inverted T method with particular emphasis on the postoperative sequelae. Significant tongue swelling persisted for longer than anticipated requiring tracheostomy to remain in situ for 14 days. 2016 BMJ Publishing Group Ltd.

BRITE/EURAM: Third Technological Days for the Basic Research in Industrial Technologies in Europe/European Research in Advanced Materials 1990, Held in Brussels, Belgium on May 21-22, 1990

Science.gov (United States)

1990-06-29

to control Five tasks being executed are: keyhole striking. Further research will design the system 5 for feeding back laser power to the level...Components ..................... 5 Development of a Reactive Ion-Plating Barrel System ................. 5 Laser Sheet Metal W elding...Automation Components ................................ 7 Closing Plenary Session ................................... 8 L. Beckmann, Deputy Director, R&D

Who is the purchaser of nutrition-labeled products?

DEFF Research Database (Denmark)

Smed, Sinne; Edenbrandt, Anna Kristina; Koch-Hansen, Pia

2017-01-01

and in the Netherlands. Design/methodology/approach We estimate probit models using a representative panel of households registering all their daily purchases during a year, three years after the introduction of a nutrition symbol in Denmark and the Netherlands (the Keyhole and the Choices). The purchase data is matched...... with information about labelling status. Other product and purchase characteristics, such as store-type and organic, are controlled for. Findings Households with children tend to have a lower probability of purchasing labelled products compared to other household types, while urbanity increases the probability...... that other aspects as the underlying attitudes and general health awareness may be of greater importance in identifying these consumers. Originality/value There is a lack of studies analyzing the effect of Front-of-Pack symbols on households’ product choices based on observed data as most previous studies...

Dissimilar joining of galvanized high-strength steel to aluminum alloy in a zero-gap lap joint configuration by two-pass laser welding

International Nuclear Information System (INIS)

Ma, Junjie; Harooni, Masoud; Carlson, Blair; Kovacevic, Radovan

2014-01-01

Highlights: • Defect-free two-pass laser partially penetrated lap joint of galvanized steel to aluminum was achieved. • The thickness of the Al-rich intermetallic compounds could be controlled by optimal parameters. • The dynamic behavior of the molten pool and keyhole were monitored by a high speed charge-coupled device camera. • The presence of zinc in the intermetallic compounds could improve the strength of the lap joints. - Abstract: A welding procedure based on using two-pass laser scans is introduced for dissimilar joining of overlapped galvanized high-strength dual-phase (DP) steel DP590 to aluminum alloy (AA) 6061 sheets. The first pass is based on a defocused laser spot that scans across the top of the two overlapped sheets and heats the zinc coating at the faying surface to be melted and partially vaporized, while the second pass is executed with a focused laser spot in order to perform the welding. Completely defect-free galvanized steel to aluminum lap joints were obtained by using this two-pass laser welding procedure. An on-line machine vision system was applied to monitor the keyhole dynamics during the laser welding process. An energy-dispersive X-ray spectroscopy (EDS) was carried out to determine the atomic percent of zinc, aluminum, and iron in the galvanized steel to aluminum lap joints. Mechanical testing and micro-hardness test were conducted to evaluate the mechanical properties of the galvanized steel to aluminum lap joints. The experimental results showed that the lap joint of galvanized steel to aluminum obtained by the two-pass laser welding approach had a higher failure value than those joints obtained when the zinc at the faying surface was mechanically removed under the same welding speed and laser power

Global Situational Awareness with Free Tools

Science.gov (United States)

2015-01-15

also be use in a closed environment • It’s cool, and people like cool 14© 2015 Carnegie Mellon University Google Earth Demo attempted-recon Signature...multiple data sources • Snort (Snorby on Security Onion) • Nagios • SharePoint RSS • Flow • Others • Leverage standard data formats • Keyhole Markup Language

Disk Laser Welding of Car Body Zinc Coated Steel Sheets / Spawanie Laserem Dyskowym Blach Ze Stali Karoseryjnej Ocynkowanej

Directory of Open Access Journals (Sweden)

Lisiecki A.

2015-12-01

Full Text Available Autogenous laser welding of 0.8 mm thick butt joints of car body electro-galvanized steel sheet DC04 was investigated. The Yb:YAG disk laser TruDisk 3302 with the beam spot diameter of 200 μm was used. The effect of laser welding parameters and technological conditions on weld shape, penetration depth, process stability, microstructure and mechanical performance was determined. It was found that the laser beam spot focused on the top surface of a butt joint tends to pass through the gap, especially in the low range of heat input and high welding speed. All test welds were welded at a keyhole mode, and the weld metal was free of porosity. Thus, the keyhole laser welding of zinc coated steel sheets in butt configuration provides excellent conditions to escape for zinc vapours, with no risk of porosity. Microstructure, microhardness and mechanical performance of the butt joints depend on laser welding conditions thus cooling rate and cooling times. The shortest cooling time t8/5 was calculated for 0.29 s.

Characteristics and performance of the variable polarity plasma arc welding process used in the Space Shuttle external tank

Science.gov (United States)

Hung, R. J.; Lee, C. C.; Liu, J. W.

1990-01-01

Significant advantages of the Variable Polarity Plasma Arc (VPPA) Welding Process include faster welding, fewer repairs, less joint preparation, reduced weldment distortion, and absence of porosity. Flow profiles and power distribution of argon plasma gas as a working fluid to produce plasma arc jet in the VPPA welding process was analyzed. Major loss of heat transfer for flow through the nozzle is convective heat transfer; for the plasma jet flow between the outlet of the nozzle and workpiece is radiative heat transfer; and for the flow through the keyhole of the workpiece is convective heat transfer. The majority of the power absorbed by the keyhole of the workpiece is used for melting the solid metal workpiece into a molten metallic puddle. The crown and root widths and the crown and root heights can be predicted. An algorithm for promoting automatic control of flow parameters and the dimensions of the final product of the welding specification to be used for the VPPA Welding System operated at MSFC are provided.

Effective capacity of multiple antenna channels: Correlation and keyhole

KAUST Repository

Zhong, Caijun; Ratnarajah, Tharm; Wong, Kaikit; Alouini, Mohamed-Slim

2012-01-01

In this study, the authors derive the effective capacity limits for multiple antenna channels which quantify the maximum achievable rate with consideration of link-layer delay-bound violation probability. Both correlated multiple-input single

Navigating on handheld displays: Dynamic versus Static Keyhole Navigation

NARCIS (Netherlands)

Mehra, S.; Werkhoven, P.; Worring, M.

2006-01-01

Handheld displays leave little space for the visualization and navigation of spatial layouts representing rich information spaces. The most common navigation method for handheld displays is static peephole navigation: The peephole is static and we move the spatial layout behind it (scrolling). A

Keyhole behaviour during laser welding of zinc-coated steel

NARCIS (Netherlands)

Pan, Y.; Richardson, I.M.

2011-01-01

The production of consistent, high-quality laser welds on zinc-coated steels for the automotive industry remains a challenge. A simple overlap joint geometry is desirable in these applications but has been shown to be extremely detrimental to laser welding because the zinc vapour formed at the

Laser power coupling efficiency in conduction and keyhole welding ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

tomacrograph showing grain orientation ... steep columnar grains of the fusion .... viz. pre-oxidation of metal surface by laser heating in air, chemical ... 4.1b Sheets of 0.5 mm thickness: Laser welds of 0.5-mm thick sheets exhibited steep angles ... boundaries of solidifying weld metal which leads to intergranular cracking ...

Shock Timing Plan for the National Ignition Campaign

Science.gov (United States)

Munro, D. H.; Robey, H. F.; Spears, B. K.; Boehly, T. R.

2006-10-01

We report progress on the design of the shock timing tuning procedure for the 2010 ignition campaign at the National Ignition Facility. Our keyhole target design provides adequate drive surrogacy for us to time the first three shocks empirically. The major risk to our plan is hard x-ray preheat, which can cause the diagnostic window to become opaque.

Evaluation of plasma arc welding capabilities and applications

International Nuclear Information System (INIS)

Mills, G.S.

1978-01-01

Unique capabilities of plasma arc welding in the keyhole mode are described, and the potential applicability of these capabilities to Rocky Flats production needs are evaluated. For the areas of potential benefits studied, the benefits of this welding technique either did not materialize or the complication of implementing the process in production was not warranted by the demonstrated benefits

Laser-GMA Hybrid Pipe Welding System

Science.gov (United States)

2007-11-01

Investigation of varying laser power. The welded pipe is shown, with close -ups of the rootside reinforcement and macro sections...68 Figure 44. Investigation of varying laser stand-off. The welded pipe is shown, along with close -ups of backside...conventional beveled joints. With appropriate joint configuration and preparation, deep keyhole penetration provided by the laser and additional filler

Multispot fiber laser welding

DEFF Research Database (Denmark)

Schutt Hansen, Klaus

This dissertation presents work and results achieved in the field of multi beam fiber laser welding. The project has had a practical approach, in which simulations and modelling have been kept at a minimum. Different methods to produce spot patterns with high power single mode fiber lasers have...... been examined and evaluated. It is found that both diamond turned DOE’s in zinc sulphide and multilevel etched DOE’s (Diffractive Optical Elements) in fused silica have a good performance. Welding with multiple beams in a butt joint configuration has been tested. Results are presented, showing it has...... been possible to control the welding width in incremental steps by adding more beams in a row. The laser power was used to independently control the keyhole and consequently the depth of fusion. An example of inline repair of a laser weld in butt joint configuration was examined. Zinc powder was placed...

The theory of laser materials processing heat and mass transfer in modern technology

CERN Document Server

Schulz, Wolfgang

2017-01-01

The revised edition of this important reference volume presents an expanded overview of the analytical and numerical approaches employed when exploring and developing modern laser materials processing techniques. The book shows how general principles can be used to obtain insight into laser processes, whether derived from fundamental physical theory or from direct observation of experimental results. The book gives readers an understanding of the strengths and limitations of simple numerical and analytical models that can then be used as the starting-point for more elaborate models of specific practical, theoretical or commercial value. Following an introduction to the mathematical formulation of some relevant classes of physical ideas, the core of the book consists of chapters addressing key applications in detail: cutting, keyhole welding, drilling, arc and hybrid laser-arc welding, hardening, cladding and forming. The second edition includes a new a chapter on glass cutting with lasers, as employed in the ...

Generation and measurement of multi megagauss fields in inertial ...

Indian Academy of Sciences (India)

We present here the development of a facility to generate high (multi megagauss) magnetic field of 4 to 5 s rise time, using inertial magnets. The facility includes a low inductance, high current capacitor bank (280 kJ/40 kV) and an inertial magnet, which is a copper disk machined to have a keyhole in it. As the high current ...

Mission Assurance, Threat Alert, Disaster Resiliency and Response (MATADRR) Product Reference Guide

Science.gov (United States)

2014-06-01

the world. Keystone implants the Google Earth KML ( Keyhole Markup Language) publishing interface to consume the Keystone Work Product sharing. Client...multiple Cores; display, close and archive incidents and work products; and monitor the health and status of the Core. Agreement Services are...to protect forces, mitigate threats, close protection gaps, and provide increased situational awareness by linking the disparate physical

A Comprehensive Comparison of the Analytical and Numerical Prediction of the Thermal History and Solidification Microstructure of Inconel 718 Products Made by Laser Powder-Bed Fusion

Directory of Open Access Journals (Sweden)

Patcharapit Promoppatum

2017-10-01

Full Text Available The finite-element (FE model and the Rosenthal equation are used to study the thermal and microstructural phenomena in the laser powder-bed fusion of Inconel 718. A primary aim is to comprehend the advantages and disadvantages of the Rosenthal equation (which provides an analytical alternative to FE analysis, and to investigate the influence of underlying assumptions on estimated results. Various physical characteristics are compared among the FE model, Rosenthal equation, and experiments. The predicted melt pool shapes compared with reported experimental results from the literature show that both the FE model and the analytical (Rosenthal equation provide a reasonably accurate estimation. At high heat input, under conditions leading to keyholing, the reported melt width is narrower than predicted by the analytical equation. Moreover, a sensitivity analysis based on choices of the absorptivity is performed, which shows that the Rosenthal approach is more sensitive to absorptivity, compared with the FE approach. The primary reason could be the effect of radiative and convective losses, which are assumed to be negligible in the Rosenthal equation. In addition, both methods predict a columnar solidification microstructure, which agrees well with experimental reports, and the primary dendrite arm spacing (PDAS predicted with the two approaches is comparable with measurements.

Real-time monitoring of laser welding of galvanized high strength steel in lap joint configuration

Science.gov (United States)

Kong, Fanrong; Ma, Junjie; Carlson, Blair; Kovacevic, Radovan

2012-10-01

Two different cases regarding the zinc coating at the lap joint faying surface are selected for studying the influence of zinc vapor on the keyhole dynamics of the weld pool and the final welding quality. One case has the zinc coating fully removed at the faying surface; while the other case retains the zinc coating on the faying surface. It is found that removal of the zinc coating at the faying surface produces a significantly better weld quality as exemplified by a lack of spatters whereas intense spatters are present when the zinc coating is present at the faying surface. Spectroscopy is used to detect the optical spectra emitted from a laser generated plasma plume during the laser welding of galvanized high strength DP980 steel in a lap-joint configuration. A correlation between the electron temperature and defects within the weld bead is identified by using the Boltzmann plot method. The laser weld pool keyhole dynamic behavior affected by a high-pressure zinc vapor generated at the faying surface of galvanized steel lap-joint is monitored in real-time by a high speed charge-coupled device (CCD) camera assisted with a green laser as an illumination source.

A canine distemper model of virus-induced anergy.

Science.gov (United States)

Mangi, R J; Munyer, T P; Krakowka, S; Jacoby, R O; Kantor, F S

1976-05-01

For development of an animal model of virus-induced anergy, the effect of canine distemper virus (CDV) upon cell-mediated immunity in dogs was investigated. First, canine cutaneous reactions and in vitro lymphocyte responses to soluble protein antigens were characterized. Dogs immunized with picryl guinea pig albumin and with keyhole limpet hemocyanin (both in complete Freund's adjuvant) responded reproducibly to intracutaneous challenge with these antigens. Reactivity peaked in 20-40 days (maximal induration, 6-50 mm). Lymphocytes from these animals responded in vitro to stimulation with keyhole limpet hemocyanin or purified protein derivative. This stimulation was antigen-specific and was maximal on day 6 of culture. Infection with CDV depressed cutaneous reactivity and lymphocyte response in vitro to antigens and mitogens. This effect was transient in animals previously vaccinated with attenuated CDV; however, gnotobiotic puppies (susceptible to CDV) had prolonged depression of cell-mediated immunity and lymphopenia. Some of these animals developed neurologic symptoms and died. The findings indicate that CDV infection is a potentially useful model for study of virus-induced depression of T (thymus)-cell responses and support the hypothesis that there is more than one mechanism responsible for this phenomenon.

Impact of video-endoscopy on the results of retrosigmoid-transmeatal microsurgery of vestibular schwannoma: prospective study

Czech Academy of Sciences Publication Activity Database

Chovanec, M.; Zvěřina, E.; Profant, Oliver; Skřivan, J.; Čakrt, O.; Lisý, J.; Betka, J.

2013-01-01

Roč. 270, č. 4 (2013), s. 1277-1284 ISSN 0937-4477 Grant - others:GA MZd(CZ) NS9909 Institutional support: RVO:68378041 Keywords : vestibular schwannoma * acoustic neuroma * endoscopy-assisted microsurgery Subject RIV: FH - Neurology Impact factor: 1.608, year: 2013

Integrating Sensor-Collected Intelligence

Science.gov (United States)

2008-11-01

APPENDIX H: ACRONYMS & GLOSSARY OF TERMS______________________________________________ KML Keyhole Markup Language L LADAR Laser Radar LAN Local... close to the sensor as possible. I endorse the Task Force’s findings and recommendations and encourage you to review the report. Dr. William...deeply-buried targets – require that the relevant sensors be in close proximity to the target. The task force discussed the requirements of close -in

The Theory of Laser Materials Processing Heat and Mass Transfer in Modern Technology

CERN Document Server

Dowden, John

2009-01-01

The purpose of the book is to show how general principles can be used to obtain insight into laser processes. The principles used may come from fundamental physical theory or from direct observation of experimental results, but an understanding of the general characteristics of the behaviour of a process is essential for intelligent investigation and implementation, whether the approach is experimental, observational, numerical or analytical. The last two have a special value since the associated costs can be relatively low and may be used as a starting point for more expensive techniques. The construction of simple models whose underlying principles are easy to see is therefore of special value, and an understanding of their strengths and limitations is essential. The applications considered in detail are cutting, keyhole welding, drilling, arc and hybrid laser-arc welding, hardening, cladding, forming and cutting, but the general principles have a very wide application; metallurgical aspects are considered,...

Experiences from Auditory Brainstem Implantation (ABIs) in four paediatric patients.

Science.gov (United States)

Lundin, Karin; Stillesjö, Fredrik; Nyberg, Gunnar; Rask-Andersen, Helge

2016-01-01

Indications for auditory brainstem implants (ABIs) have been widened from patients with neurofibromatosis type 2 (NF2) to paediatric patients with congenital cochlear malformations, cochlear nerve hypoplasia/aplasia, or cochlear ossification after meningitis. We present four ABI surgeries performed in children at Uppsala University Hospital in Sweden since 2009. Three children were implanted with implants from Cochlear Ltd. (Lane Cove, Australia) and one child with an implant from MedEl GMBH (Innsbruck, Austria). A boy with Goldenhar syndrome was implanted with a Cochlear Nucleus ABI24M at age 2 years (patient 1). Another boy with CHARGE syndrome was implanted with a Cochlear Nucleus ABI541 at age 2.5 years (patient 2). Another boy with post-ossification meningitis was implanted with a Cochlear Nucleus ABI24M at age 4 years (patient 3). A girl with cochlear aplasia was implanted with a MedEl Synchrony ABI at age 3 years (patient 4). In patients 1, 2, and 3, the trans-labyrinthine approach was used, and in patient 4 the retro-sigmoid approach was used. Three of the four children benefited from their ABIs and use it full time. Two of the full time users had categories of auditory performance (CAP) score of 4 at their last follow up visit (6 and 2.5 years postoperative) which means they can discriminate consistently any combination of two of Ling's sounds. One child has not been fully evaluated yet, but is a full time user and had CAP 2 (responds to speech sounds) after 3 months of ABI use. No severe side or unpleasant stimulation effects have been observed so far. There was one case of immediate electrode migration and one case of implant device failure after 6.5 years. ABI should be considered as an option in the rehabilitation of children with similar diagnoses.

Assessment of Joint Improvised Explosive Device Defeat Organization (JIEDDO) Training Activity

Science.gov (United States)

2013-01-01

the RAND study team was asked to assess whether JIEDDO duplicated or showed close similarity to the training programs and functions already...duplication and relatively few cases of close similarity. We also note that Services or CCMDs did use the programs provided and indicated that they used...tailored interactive modules. TBD ALL Home station/CTC/ Theater VISDeS The expansion of KEYHOLE /Route Clearance Optic System/Marine Corps EOD Optic

The Use of Satellite Imagery for Domestic Law Enforcement

Science.gov (United States)

2013-12-01

traditionally conducted in a surveillance covey within close proximity to a potential perpetrator, may today involve a greater standoff that necessitate a...surveillance techniques, modern policing has been become to a science unto itself. What was traditionally conducted in a surveillance covey, within close ...current systems, the pictures still provided early analyst a means to determine an area order of battle. Specific weapons system and 17 Keyhole (KH

Unconventional High Density Vertically Aligned Conducting Polymer

Science.gov (United States)

2014-08-21

gravimetric values of an electrode. As shown in Table 1, there is a close correlation between the specific gravimetric performance in terms of the whole...to 10nm, exhibit nearly ideal capacitive behavior (so that the Coulombic efficiency shows only a slight decrease, and is overall very close to 100...PEDOT thickness while avoiding keyhole formation (i.e., PEDOT blocking the ion channels), is a viable route towards increasing electrode performance

A Glycoform of Immunoglobulin G (IgG) as an Early Biomarker of Exposure to Nonhuman Substances

Science.gov (United States)

2012-12-01

the usual closed conformation adopted by immunoglobulin CH2 domains, which are known to deny all glycan access. 15. SUBJECT TERMS Aleuria aurantia...reactive IgG in the closed conformation and AAL-reactive IgG, or primebody, in the flip-out conformation .....................15 TABLES...adjuvant b IP, intraperitoneal injection c KLH, keyhole limpet hemocyanin d N/A, not applicable e CFA, complete Freund’s adjuvant f RV, rabies

Thermal Analysis and Microhardness Mapping in Hybrid Laser Welds in a Structural Steel

Science.gov (United States)

2003-01-01

conditions. Via the keyhole the laser beam brings about easier ignition of the arc, stabilization of the arc welding process, and penetration of the...with respect to the conventional GMAW or GTAW processes without the need for very close fit-up. This paper will compare an autogenous laser weld to a...UNCLASSIFIED Defense Technical Information Center Compilation Part Notice ADP017864 TITLE: Thermal Analysis and Microhardness Mapping in Hybrid Laser

Plant antigens cross-react with rat polyclonal antibodies against

Czech Academy of Sciences Publication Activity Database

Oulehlová, Denisa; Hála, Michal; Potocký, Martin; Žárský, Viktor; Cvrčková, F.

2009-01-01

Roč. 33, č. 1 (2009), s. 113-118 ISSN 1065-6995 R&D Projects: GA AV ČR KJB600380601; GA ČR GA204/05/0268; GA MŠk(CZ) LC06004; GA MŠk(CZ) LC06034 Institutional research plan: CEZ:AV0Z50380511 Keywords : Keyhole limpet hemocyanin * Rat antisera * Synthetic peptides Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 1.800, year: 2009

Low temperature heat treatments of AA5754-Ti6Al4V dissimilar laser welds: Microstructure evolution and mechanical properties

Science.gov (United States)

Leo, P.; D'Ostuni, S.; Casalino, G.

2018-03-01

This paper presents the effects of the post welding heat treatments (PWHT) performed at 350 °C and 450 °C on the microstructure evolution and mechanical properties of AA5754 and Ti6Al4V dissimilar laser welds. The microstructure and tensile properties of the welds before and after low temperature treatment were analyzed. The off-set welding technique was applied to limit the formation of brittle intermetallic compounds during the welding process. The laser beam was directed onto the titanium side at a small distance from the aluminum edge. The keyhole formed and the full penetration was reached in the titanium side of the weld. Thereafter, the aluminum side melted as the heat that formed the keyhole transferred from the titanium fused zone. Two different energy lines (32 J/mm and 76 J/mm) were used. In this manner, a fused and a heat affected zones was revealed on both sides of the weld. Several intermetallic compounds formed in the intermetallic layer between the two metals. The thickness and the composition of the intermetallic layer depended on the welding parameters and the post welding heat treatment. The hardness and tensile properties of the welds before and after the post welding heat treatment were measured and analyzed.

GEOREFERENCED IMAGE SYSTEM WITH DRONES

Directory of Open Access Journals (Sweden)

Héctor A. Pérez-Sánchez

2017-07-01

Full Text Available This paper has as general purpose develop and implementation of a system that allows the generation of flight routes for a drone, the acquisition of geographic location information (GPS during the flight and taking photographs of points of interest for creating georeferenced images, same that will be used to generate KML files (Keyhole Markup Language for the representation of geographical data in three dimensions to be displayed on the Google Earth tool.

Plan Recognition using Statistical Relational Models

Science.gov (United States)

2014-08-25

corresponding undirected model can be significantly more complex since there is no closed form solution for the maximum-likelihood set of parameters unlike in...algorithm did not scale to larger training sets, and the overall results are still not competitive with BALPs. 5In directed models, a closed form solution...opinions of ARO, DARPA, NSF or any other government agency. References Albrecht DW, Zukerman I, Nicholson AE. Bayesian models for keyhole plan

2009 Navy ManTech Project Book

Science.gov (United States)

2009-01-01

build a hybrid laser / GMAW system that combined deep keyhole penetration of laser welding with the high metal deposition rate of GMAW, enabling...committed to the successful outcome of the ManTech project. In addition, this close working relationship between the parties provides ManTech with a longer...the cost and time to build and repair Navy ships. The Center works closely with the Navy’s acquisition community and the shipbuilding industry to

The Marine Corps Needs a Targeting, Sensors, and Surveillance Systems Operational Integration and Support Team

Science.gov (United States)

2010-03-02

triggerman is probably still close ; lately all IEDs in the area have been initiated via command-wire. The squad leader sets a cordon, ensures an IED 9...Operational Surveillance System (G-BOSS) with a Class IIIb laser pointer. This class of laser requires users to receive a laser safety class...2) The Keyhole kit of surveillance equipment. Designed to provide “snipers with an increased capability to visually detect the enemy emplacing IEDs

Navy MANTECH 2008 Project Book

Science.gov (United States)

2008-01-01

and Shipbuilding Company (NASSCO) to design and build a hybrid laser / GMAW system that combines the deep keyhole pen- etration of laser welding with...ance that the weapon system PM is truly committed to the successful outcome of the ManTech project. In addition, this close working relationship...will reduce the cost and time to build and repair Navy ships. The Center works closely with the Navy’s acquisition community and the shipbuilding

The Regulation of Polysaccharide Specific Humoral Immune Response Against Intact Streptococcus Pneumoniae

Science.gov (United States)

2008-06-19

periods of time, and 25% to 75% of infants carry pneumococci at any given time. High colonization rates are promoted by children who are in close ...PC- keyhole limpet hemocyanin (KLH) was synthesized as described previously (Wu, Vos et al. 1999). The resulting conjugate had a substitution degree...635 lasers and results generated using Winlist software. For isolation of MZB and FB cells, RBC-lysed spleen cells were 44 stained for these B cell

Keyhole: Equal signs as bridges between the phenomenological and theoretical dimensions

DEFF Research Database (Denmark)

Kneubil, Fabiana; Avelar Sotomaior Karam, Ricardo

2016-01-01

reasoning allows us to determine the radius of a hydrogen atom from the experimental measure of the atom's binding energy. The third example comes from kinetic gas theory and illustrates how it is possible to estimate the number of gas particles per unit volume from the experimental values of pressure...... three case studies. In the first one, the explanation of the Hall effect underlines how we indirectly penetrate into the microscopic structure of a wire and manage to evaluate the number of charged particles per unit volume inside it from a set of macroscopic measurements. The second case shows how our...

A Biological Model of the Effects of Toxic Substances

Science.gov (United States)

1990-02-28

show uner te hghes aenifia in (lwerrigh) te neron (arows ar ofte ovl i shpe nd "igh~up wih pace pti. mgniicaion Fig, 12 A neuron viewed under Hoffman...keyhole), the neurons seem to form a more substantial network . Scratches in the collagen surface controlled the direction of axon sprouting such that...Fig. 5). Templates could be removed without disturbing the neural network and hence might be a valuable tool in the future to focus the growth of

Medical Department, United States Army. Wound Ballistics for World War II.

Science.gov (United States)

1962-01-01

Similarly, there were elliptic entry wounds, a result of the " keyholing " effect of bullets hitting with their sides. Table 2 gives a description of small...interlocked welded steel, and their turrets were constructed in one piece in order to give sufficient rigidity. The King Tiger was virtually invulnerable...Reed N. Fitch, T4g. Charles J. Berzenyi, and TIg . Charles R. Restife. The team was organized to participate in the contemplated New Ireland operation

Development of Immunoassay Based on Monoclonal Antibody Reacted with the Neonicotinoid Insecticides Clothianidin and Dinotefuran

OpenAIRE

Uchigashima, Mikiko; Watanabe, Eiki; Ito, Shigekazu; Iwasa, Seiji; Miyake, Shiro

2012-01-01

Enzyme-linked immunosorbent assay (ELISA) based on a monoclonal antibody (MoAb) was developed for the neonicotinoid insecticide clothianidin. A new clothianidin hapten (3-[5-(3-methyl-2-nitroguanidinomethyl)-1,3-thiazol-2-ylthio] propionic acid) was synthesized and conjugated to keyhole limpet hemocyanin, and was used for monoclonal antibody preparation. The resulting MoAb CTN-16A3-13 was characterized by a direct competitive ELISA (dc-ELISA). The 50% of inhibition concentration value with cl...

INTEREST OF FINITE ELEMENT ANALYSIS TO DETERMINE STRESS FIELDS AT THE SUMMIT OF A VY FLAP ABOUT ONE CLINICAL CASE

OpenAIRE

Pauchot , Julien; Remache , Djamel; Chambert , Jérôme; Elkhyat , Ahmed; Jacquet , Emmanuelle

2013-01-01

International audience; After performing a V-Y advancement flap, we observed an unusually shaped necrosis, resembling a keyhole at the apex of the flap. As high closing tensions are an accepted cause of skin necrosis, we developed a mathematical model based on the finite element analysis in order to determine the stress field by simulating the mechanical behavior of human skin during suture and to explain this particular shape of necrosis. For the modeling, a planar nonlinear two-dimensional ...

Local-Rapid Evaluation of Atmospheric Conditions (L-REAC) System, Design and Development Volume 5 (Mobile L-REAC System Proof of Concept and Four Feasibility Studies)

Science.gov (United States)

2012-12-01

Earth satellite map. (See figure 4.) These overlays were written in keyhole markup language (kml) format. This format was chosen, so that the...this icon, they would then initiate the two L-REAC® HTML windows. The L-REAC® output and automated updates would continue until the user closed ...packaged in an icon that could easily be copied onto the user desktop and, the L-REAC® output remained visible from the user’s PC until the user closed

An assessment of the 3D geometric surrogacy of shock timing diagnostic techniques for tuning experiments on the NIF

Energy Technology Data Exchange (ETDEWEB)

Robey, H F; Munro, D H; Spears, B K; Marinak, M M; Jones, O S; Patel, M V; Haan, S W; Salmonson, J D; Landen, O L [Lawrence Livermore National Laboratory, Livermore, CA (United States); Boehly, T R [Laboratory for Laser Energetics, Rochester, NY (United States); Nikroo, A [General Atomics, San Diego, CA (United States)], E-mail: robey1@llnl.gov

2008-05-15

Ignition capsule implosions planned for the National Ignition Facility (NIF) require a pulse shape with a carefully designed series of four steps, which launch a corresponding series of shocks through the ablator and DT ice shell. The relative timing of these shocks is critical for maintaining the DT fuel on a low adiabat. The current NIF specification requires that the timing of all four shocks be tuned to an accuracy of {<=} +/- 100ps. To meet these stringent requirements, dedicated tuning experiments are being planned to measure and adjust the shock timing on NIF. These tuning experiments will be performed in a modified hohlraum geometry, where a re-entrant Au cone is added to the standard NIF hohlraum to provide optical diagnostic (VISAR and SOP) access to the shocks as they break out of the ablator. This modified geometry is referred to as the 'keyhole' hohlraum and introduces a geometric difference between these tuning-experiments and the full ignition geometry. In order to assess the surrogacy of this modified geometry, 3D simulations using HYDRA [1] have been performed. The results from simulations of a quarter of the target geometry are presented. Comparisons of the hohlraum drive conditions and the resulting effect on the shock timing in the keyhole hohlraum are compared with the corresponding results for the standard ignition hohlraum.

An assessment of the 3D geometric surrogacy of shock timing diagnostic techniques for tuning experiments on the NIF

International Nuclear Information System (INIS)

Robey, H F; Munro, D H; Spears, B K; Marinak, M M; Jones, O S; Patel, M V; Haan, S W; Salmonson, J D; Landen, O L; Boehly, T R; Nikroo, A

2008-01-01

Ignition capsule implosions planned for the National Ignition Facility (NIF) require a pulse shape with a carefully designed series of four steps, which launch a corresponding series of shocks through the ablator and DT ice shell. The relative timing of these shocks is critical for maintaining the DT fuel on a low adiabat. The current NIF specification requires that the timing of all four shocks be tuned to an accuracy of ≤ +/- 100ps. To meet these stringent requirements, dedicated tuning experiments are being planned to measure and adjust the shock timing on NIF. These tuning experiments will be performed in a modified hohlraum geometry, where a re-entrant Au cone is added to the standard NIF hohlraum to provide optical diagnostic (VISAR and SOP) access to the shocks as they break out of the ablator. This modified geometry is referred to as the 'keyhole' hohlraum and introduces a geometric difference between these tuning-experiments and the full ignition geometry. In order to assess the surrogacy of this modified geometry, 3D simulations using HYDRA [1] have been performed. The results from simulations of a quarter of the target geometry are presented. Comparisons of the hohlraum drive conditions and the resulting effect on the shock timing in the keyhole hohlraum are compared with the corresponding results for the standard ignition hohlraum

Intracapsular implant rupture: MR findings of incomplete shell collapse.

Science.gov (United States)

Soo, M S; Kornguth, P J; Walsh, R; Elenberger, C; Georgiade, G S; DeLong, D; Spritzer, C E

1997-01-01

The objective of this study was to determine the frequency and significance of the MR findings of incomplete shell collapse for detecting implant rupture in a series of surgically removed breast prostheses. MR images of 86 breast implants in 44 patients were studied retrospectively and correlated with surgical findings at explantation. MR findings included (a) complete shell collapse (linguine sign), 21 implants; (b) incomplete shell collapse (subcapsular line sign, teardrop sign, and keyhole sign), 33 implants; (c) radial folds, 31 implants; and (d) normal, 1 implant. The subcapsular line sign was seen in 26 implants, the teardrop sign was seen in 27 implants, and the keyhole sign was seen in 23 implants. At surgery, 48 implants were found to be ruptured and 38 were intact. The MR findings of ruptured implants showed signs of incomplete collapse in 52% (n = 25), linguine sign in 44% (n = 21), and radial folds in 4% (n = 2). The linguine sign perfectly predicted implant rupture, but sensitivity was low. Findings of incomplete shell collapse improved sensitivity and negative predictive values, and the subcapsular line sign produced a significant incremental increase in predictive ability. MRI signs of incomplete shell collapse were more common than the linguine sign in ruptured implants and are significant contributors to the high sensitivity and negative predictive values of MRI for evaluating implant integrity.

Multimodality Imaging-based Evaluation of Single-Lumen Silicone Breast Implants for Rupture.

Science.gov (United States)

Seiler, Stephen J; Sharma, Pooja B; Hayes, Jody C; Ganti, Ramapriya; Mootz, Ann R; Eads, Emily D; Teotia, Sumeet S; Evans, W Phil

2017-01-01

Breast implants are frequently encountered on breast imaging studies, and it is essential for any radiologist interpreting these studies to be able to correctly assess implant integrity. Ruptures of silicone gel-filled implants often occur without becoming clinically obvious and are incidentally detected at imaging. Early diagnosis of implant rupture is important because surgical removal of extracapsular silicone in the breast parenchyma and lymphatics is difficult. Conversely, misdiagnosis of rupture may prompt a patient to undergo unnecessary additional surgery to remove the implant. Mammography is the most common breast imaging examination performed and can readily depict extracapsular free silicone, although it is insensitive for detection of intracapsular implant rupture. Ultrasonography (US) can be used to assess the internal structure of the implant and may provide an economical method for initial implant assessment. Common US signs of intracapsular rupture include the "keyhole" or "noose" sign, subcapsular line sign, and "stepladder" sign; extracapsular silicone has a distinctive "snowstorm" or echogenic noise appearance. Magnetic resonance (MR) imaging is the most accurate and reliable means for assessment of implant rupture and is highly sensitive for detection of both intracapsular and extracapsular rupture. MR imaging findings of intracapsular rupture include the keyhole or noose sign, subcapsular line sign, and "linguine" sign, and silicone-selective MR imaging sequences are highly sensitive to small amounts of extracapsular silicone. © RSNA, 2017.

Geoinformation perspectives on innovation and economic growth

CSIR Research Space (South Africa)

Cooper, Antony K

2009-03-01

Full Text Available driving patterns, monitored through a tracking device placed in the insured person’s vehicle. circle6 Real estate: Real estate agencies have been pioneers of incorporating multimedia into a GIS, to link photographs and video footage of properties... geobrowsers. With markup languages such as the Keyhole Markup Language (KML), geobrowsers can be customised to drape one’s geoinformation over the virtual globe, attach one’s content (eg: photographs, video or sound recordings) to locations in the virtual...

A very rare, petro-clival, neurothekeoma tumor. Case Report

Directory of Open Access Journals (Sweden)

Iacob G.

2015-09-01

Full Text Available Known as nerve sheath myxoma too, neurothekeoma are benign tumors, usually arise in the skin of the head, neck region and upper extremities, in young females. Cerebral neurothekeoma are very rare, a few cases were already described in the parasellar area, in the middle cranial and posterior fossa. We present a petro-clival neurotekoma. A 78-year-old male was admitted for two years left fronto-temporal headache completed in the last 6 months with left trigeminal V1 neuralgia, left facial hypoesthesia, diplopia, swallowing disorders for liquid foods, balance disorders. From his medical records we noticed: stage 2 chronic kidney disease, hypertension, prostate adenoma, dyslipidemia hypercholesterolemia. The MRI showed a macronodular petroclival mass in hiper T2, hipo T1, flair iso signal; normal cerebral angiography. The patient was operated on using a left retrosigmoid, retromastoidian approach. A 4/3/3 cm tumor, gray, encapsulated, soft consistency, partially cystic, less bleeding, attached to the dura, displacing the basilar artery and brain stem controlateral, encasing the trigeminal nerve. The tumor was totally removed with a good postop evolution. Six months follow up he had no more facial pain, but only persistant left facial hypoesthesia. Histologically the tumor had lobular appearance with spindle or stellate cells embedded in abundant myxoid background. The tumor cells were diffusely positive for S100, PGP9.5’, CD 34” positive in vessels, Ki67’positive in 5%. Cranial MRI performed one month after surgery did not show any residual tumor. Also known as nerve sheath myxomas, neurothekoma are rare benign tumors. For intracranial neurothekoma surgical indication is mandatory

A Study of the Dependence of Microsegregation on Critical Solidification Parameters in Rapidly-Quenched Structures.

Science.gov (United States)

1980-12-01

a formulation given in many sources (Refs. 1-3). The laser is assumed to penetrate completely through the material (making a " keyhole ") and the heat...absorbed laser power as determined from calor- imetric measurements. The analytical predictions were brought to close agree- ment with the experimental...kW power setting would be about 45 kW/cm 2. This value is close to the 50 kW/cm2 line predicted by the model. As in Fig. 13, the laser dwell time is

Vectors for Treatment of Metastatic Breast Cancer

Science.gov (United States)

2006-08-01

hMUC-1/ecdCD40L protein (F): bacterial cell lysate (), keyhole limpet hemocyanin (KLH)- conjugated hMUC-1 Ag with (E) and without (‚) IFA, and PBS...antimouse CD11C antibody were added to the purified DCs. (iii) Cells exposed to a laser excitatory for phycoerythrin. (iv) Cells exposed to a laser ...under nondenaturing conditions was close to 3 Figure 4. The ecdhMUC1 protein released from Ad-sig-ecdhMUC1/ecdCD40L vector–infected cells forms

Detection of defects in laser welding of AZ31B magnesium alloy in zero-gap lap joint configuration by a real-time spectroscopic analysis

Science.gov (United States)

Harooni, Masoud; Carlson, Blair; Kovacevic, Radovan

2014-05-01

The effect of surface oxide layer existing at the lap-joint faying surface of magnesium sheets is investigated on the keyhole dynamics of the weld pool and weld bead qualities. It is observed that by removing the oxide layer from the faying surface of the lap joint, a high quality weld can be achieved in the laser welding process. However, the presence of an oxide layer deteriorates the quality of the weld by forming pores at the interface of the two overlapped sheets. The purpose of this paper is to identify the correlation between the integrity of the weld and the interaction between the laser and material. A spectroscopy sensor was applied to detect the spectra emitted from a plasma plume during the laser welding of AZ31B magnesium alloy in a zero-gap lap joint configuration. The electron temperature was calculated by applying a Boltzmann plot method based on the detected spectra, and the correlation between the pore formation and the spectral signals was studied. The laser molten pool and the keyhole condition were monitored in real-time by a high speed charge-coupled device (CCD) camera. A green laser was used as an illumination source in order to detect the influence of the oxide layer on the dynamic behavior of the molten pool. Results revealed that the detected spectrum and weld defects had a meaningful correlation for real-time monitoring of the weld quality during laser welding of magnesium alloys.

Domain Approach: An Alternative Approach in Moral Education

Science.gov (United States)

Vengadasalam, Chander; Mamat, Wan Hasmah Wan; Mail, Fauziah; Sudramanian, Munimah

2014-01-01

This paper discusses the use of the domain approach in moral education in an upper secondary school in Malaysia. Moral Education needs a creative and an innovative approach. Therefore, a few forms of approaches are used in the teaching-learning of Moral Education. This research describes the use of domain approach which comprises the moral domain…

Interactions between laser and arc plasma during laser-arc hybrid welding of magnesium alloy

Science.gov (United States)

Liu, Liming; Chen, Minghua

2011-09-01

This paper presents the results of the investigation on the interactions between laser and arc plasma during laser-arc hybrid welding on magnesium alloy AZ31B using the spectral diagnose technique. By comparably analyzing the variation in plasma information (the shape, the electron temperature and density) of single tungsten inert gas (TIG) welding with the laser-arc hybrid welding, it is found that the laser affects the arc plasma through the keyhole forming on the workpiece. Depending on the welding parameters there are three kinds of interactions taking place between laser and arc plasma.

Sialyl-Tn vaccine induces antibody-mediated tumour protection in a relevant murine model

DEFF Research Database (Denmark)

Julien, S; Picco, G; Sewell, R

2009-01-01

challenge. We show that synthetic STn coupled to keyhole limpet haemocyanin (Theratope), induced antibodies to STn that recognised the glycan carried on a number of glycoproteins and in these mice a significant delay in tumour growth was observed. The protection was dependent on STn being expressed...... by the tumour and was antibody mediated. Affinity chromatography of the STn-expressing tumour cell line, followed by mass spectrometry, identified osteopontin as a novel STn-carrying glycoprotein which was highly expressed by the tumours. These results suggest that if antibodies can be induced to a number...

Polyclonal cell activity of a repeat peptide derived from the sequence of an 85-kilodalton surface protein of Trypanosoma cruzi trypomastigotes.

Science.gov (United States)

Pestel, J; Defoort, J P; Gras-Masse, H; Afchain, D; Capron, A; Tartar, A; Ouaissi, A

1992-01-01

Some in vitro and in vivo biological activities of an octadecapeptide derived from an 85-kDa surface protein of Trypanosoma cruzi trypomastigote were studied. The peptide coupled to a carrier protein induced the proliferative response of lymph node cells from mice immunized with various antigens. Moreover, sera from mice immunized with the coupled peptide were found to contain antibodies against a number of self and nonself antigens: fibronectin, bovine serum albumin, myosin, tetanus toxoid, ovalbumin, keyhole limpet hemocyanin, and DNA. These results are discussed in the context of Chagas' disease immunopathology. PMID:1730508

Valuation of dynamic MR imaging for diagnosis of pituitary microadenomas

International Nuclear Information System (INIS)

Lu Wu; Zhou Shengli; Liu Yusheng

2003-01-01

Objective: To evaluate the use of keyhole dynamic magnetic resonance (MR) imaging in evaluation of pituitary microadenomas. Methods: Fifty-three patients with pituitary microadenomas proved by operation or clinical findings such as headache, amenorrhea, lactating, fat or acromegaly were retrospectively studied on dynamic MR, conventional contrast enhanced MR, and unenhanced MR. Then the image data were analyzed by two experienced doctors who didn't know the details and three degrees were made as follows: grade 0, no evidence of the tumor; grade I, asymmetry signals in the pituitary; and grade II, nodulated or sheets signals in the pituitary. The grading data were compared with statistical methods. Results: In dynamic MR grading system: grade 0 was revealed in 1 patient, grade I in 29 patients and grade II in 23 patients. In conventional enhanced MR: grade 0 in 26 patients, grade I in 17 patients and grade II in 10 patients. In conventional unenhanced MR: grade 0 in 39 patients, grade I in 10 patients and grade II in 4 patients. The diagnostic rate of dynamic MR, conventional enhanced MR, and unenhanced MR was 98.1%, 51.9%, and 26.4%, respectively. (P < 0.005). Dynamic MR can increase the grade of tumor compared to the other two, which is significant statistically. Conclusion: Keyhole dynamic MR can increase the diagnostic accuracy of pituitary microadenomas while decreasing the uncertainty. So dynamic MR should become a routine examination for pituitary microadenoma when suspected by clinical findings but negative in conventional MR

Secondary hazards of high power laser beam welding

International Nuclear Information System (INIS)

Schulmeister, K.; Schmitzer, C.; Duftschmid, K.; Liedl, G.; Schroeder, K.; Schuoecker, D.

1996-01-01

Hazardous UV-radiation and short-wavelength visible (blue) light is emitted by the high temperature plasma above the welding-keyhole. Ozone and NO x is produced due to UV-induced photodissociation of oxygen and high temperature gas-phase reactions. Spectral measurements of the plasma emission show that the allowed dose for UV-radiation and blue light exposure per work day can be exceeded in as short as a few seconds. Similarly, measurements and models of the ozone and NO x concentration show that the maximum workplace concentrations might be reached quickly if no appropriate exhaust and filter system is installed. (author)

Crack Propagation by Finite Element Method

Directory of Open Access Journals (Sweden)

Luiz Carlos H. Ricardo

2018-01-01

Full Text Available Crack propagation simulation began with the development of the finite element method; the analyses were conducted to obtain a basic understanding of the crack growth. Today structural and materials engineers develop structures and materials properties using this technique. The aim of this paper is to verify the effect of different crack propagation rates in determination of crack opening and closing stress of an ASTM specimen under a standard suspension spectrum loading from FDandE SAE Keyhole Specimen Test Load Histories by finite element analysis. To understand the crack propagation processes under variable amplitude loading, retardation effects are observed

Thermocapillary and arc phenomena in stainless steel welds

Energy Technology Data Exchange (ETDEWEB)

Pierce, Stanley W. [Colorado School of Mines, Golden, CO (United States)

1993-01-01

Goal was to study effect of power level and distribution on thermocapiilary-induced weld shape and of arc factors on weld shape. Thermocapillarity was apparent in both conduction mode EB welds and GTA welds, particularly in the former. A non-Gaussian arc distribution is suggested for accounting for the differences between the twoss processes. At higher current levels (200--300 A), plasma shear force also contributes to weld shape development. Evidence suggests that thermocapillary flow reversal is not a factor in normal GTA welds; EDB flow reversal occurs only at high power density levels where the keyhole mode is present.

PAMTRAK: A personnel and material tracking system

International Nuclear Information System (INIS)

Anspach, D.A.; Anspach, J.P.; Crain, B. Jr.

1996-01-01

There is a need for an automated system for protecting and monitoring sensitive or classified parts and material. Sandia has developed a real-time personnel and material tracking system (PAMTRAK) that has been installed at selected DOE facilities. It safeguards sensitive parts and material by tracking tags worn by personnel and by monitoring sensors attached to the parts or material. It includes remote control and alarm display capabilities and a complementary program in Keyhole to display measured material attributes remotely. This paper describes the design goals, the system components, current installations, and the benefits a site can expect when using PAMTRAK

Low dose ultraviolet B-irradiated Langerhans cells preferentially activate CD4+ cells of the T helper 2 subset

International Nuclear Information System (INIS)

Simon, J.C.; Cruz, P.D. Jr.; Bergstresser, P.R.; Tigelaar, R.E.

1990-01-01

UVB radiation distorts the Ag-presenting function of epidermal Langerhans cells (LC); this has been shown for the presentation of soluble Ag to primed T cells in vitro and for the initiation of delayed-type hypersensitivity in vivo, such as contact hypersensitivity (CH). Previous work has also demonstrated UVB-induced suppression of CH to be mediated ultimately by T cells. Two subsets of CD4+ Th cells, Th1 and Th2, have been identified, based on their cytokine production and functional activities. In particular, Th1 mediate delayed-type hypersensitivity, whereas Th2 do not. To investigate whether the perturbation of LC function induced by UVB radiation leads to a differential activation of these subsets of CD4+ cells, we examined the capacity of unirradiated and irradiated (200 J/m2) APC from adult BALB/c mice to present keyhole limpet hemocyanin to Ag-specific, H2d-restricted Th1 and Th2 cell lines. Four sources of APC were utilized: epidermal cells (EC), flow microfluorometry-purified Ia+ EC (LC), flow microfluorometry-purified Ia- EC, and splenic adherent cells (SAC). Unirradiated EC, LC, and SAC, but not Ia-EC, presented keyhole limpet hemocyanin to both Th1 and Th2. Irradiated EC and LC lost their ability to stimulate Th1, but retained fully their capacity to stimulate Th2. On the other hand, irradiated SAC were unable to induce proliferation of either Th1 or Th2. These findings indicate that suppression of CH mediated by UVB-irradiated LC may result from an alteration of the ratio and/or activity of Th1 and Th2 cells normally generated during the induction of such responses

Modelización del perfil de soldadura y de la cavidad de vapor en la aleación de aluminio 5182 soldada con láser

Directory of Open Access Journals (Sweden)

Pastor, M.

2001-12-01

Full Text Available The purpose of this research is the study of the laser welding process of the aluminum alloy 5182 and the development of models by means of the COSMOS/M package, in order to predict the shape of the keyhole and the temperatures profile of the weld. Modeling has been done considering the degree of defocusing. The heat flow applied on the models was a Gauss flow, considering the condition of the focused face and the conditions of negative and positive defocusing. The validity of the models has been demonstrated comparing their results with those obtained by experimental tests. The extent of defocusing of laser beam affected the stability of the keyhole and welding geometry.

El presente trabajo se introduce en el desarrollo de modelos para predecir la forma de la cavidad de vapor y el perfil de la aleación de aluminio 5182 con soldadura láser. Para el procesamiento del modelo se ha empleado el paquete profesional de Elementos Finitos COSMOS/M. La modelización de la soldadura se realizó considerando como variable el grado de desenfoque del haz de láser y la distribución del flujo de calor según un modelo Gaussiano, para las condiciones de haz enfocado y de desenfoque negativo y positivo. La validez de los resultados obtenidos se comprobó mediante la comparación con los resultados obtenidos en pruebas experimentales, concluyéndose que el grado de desenfoque del haz del láser afecta notablemente la estabilidad de la cavidad de vapor y la geometría de la soldadura.

Early burn wound excision and skin grafting postburn trauma restores in vivo neutrophil delivery to inflammatory lesions

International Nuclear Information System (INIS)

Tchervenkov, J.I.; Epstein, M.D.; Silberstein, E.B.; Alexander, J.W.

1988-01-01

This study assessed the effect of early vs delayed postburn wound excision and skin grafting on the in vivo neutrophil delivery to a delayed-type hypersensitivity (DTH) reaction and a bacterial skin lesion (BSL). Male Lewis rats were presensitized to keyhole-limpet hemocyanin. Group 1 comprised sham controls. Groups 2 through 4 were given a 30% 3 degrees scald burn, but the burn wounds were excised, and skin was grafted on days 1, 3, and 7, respectively, after the burn. Group 5 comprised burn controls. Twelve days after burn trauma, all rats were injected at different intervals (during a 24-hour period) with a trio of intradermal injections of keyhole-limpet hemocyanin, Staphylococcus aureus 502A, and saline at different sites. In vivo neutrophil delivery to these dermal lesions was determined by injecting indium in 111 oxyquinoline-labeled neutrophils isolated from similarly treated groups of rats. Neutrophil delivery to DTH and BSL lesions was restored to normal by excision and skin grafting of the burn wound one day after burn trauma. Waiting three days after burn trauma to excise and skin graft the wound partially, but not completely, restored the in vivo neutrophil delivery to DTH and BSL lesions. Waiting one week to excise and skin graft a burn wound resulted in no improvement in neutrophil delivery to DTH and BSL dermal lesions. It was concluded that burn wound excision and skin grafting immediately after burn trauma restored in vivo neutrophil delivery to a BSL and DTH dermal lesion. This may, in part, explain the beneficial effect of early aggressive burn wound debridement in patients with burn injuries

Dendritic cells pulsed with a tumor-specific peptide induce long-lasting immunity and are effective against murine intracerebral melanoma.

Science.gov (United States)

Heimberger, Amy B; Archer, Gary E; Crotty, Laura E; McLendon, Roger E; Friedman, Allan H; Friedman, Henry S; Bigner, Darell D; Sampson, John H

2002-01-01

Dendritic cells (DCs) are specialized cells of the immune system that are capable of generating potent immune responses that are active even within the "immunologically privileged" central nervous system. However, immune responses generated by DCs have also been demonstrated to produce clinically significant autoimmunity. Targeting the epidermal growth factor receptor variant III (EGFRvIII), which is a mutation specific to tumor tissue, could eliminate this risk. The purpose of this study was to demonstrate that DC-based immunizations directed solely against this tumor-specific antigen, which is commonly found on tumors that originate within or metastasize to the brain, could be efficacious. C3H mice were vaccinated with DCs mixed with a keyhole limpet hemocyanin conjugate of the tumor-specific peptide, PEP-3, which spans the EGFRvIII mutation, or the random-sequence peptide, PEP-1, and were intracerebrally challenged with a syngeneic melanoma expressing a murine homologue of EGFRvIII. Systemic immunization with DCs mixed with PEP-3-keyhole limpet hemocyanin generated antigen-specific immunity. Among mice challenged with intracerebral tumors, this resulted in an approximately 600% increase in the median survival time (>300 d, P < 0.0016), relative to control values. Sixty-three percent of mice treated with DCs mixed with the tumor-specific peptide survived in the long term and 100% survived rechallenge with tumor, indicating that antitumor immunological memory was also induced. In a murine melanoma model, immunization with DCs mixed with tumor-specific peptide results in an antigen-specific immunological response that recognizes the EGFRvIII mutation, has potent antitumor efficacy against intracerebral tumors that express EGFRvIII, and results in long-lasting antitumor immunity.

Post-modelling of images from a laser-induced wavy boiling front

Energy Technology Data Exchange (ETDEWEB)

Matti, R.S., E-mail: ramiz.matti@ltu.se [Luleå University of Technology, Department of Engineering Sciences and Mathematics, SE-971 87 Luleå (Sweden); University of Mosul, College of Engineering, Department of Mechanical Engineering, Mosul (Iraq); Kaplan, A.F.H. [Luleå University of Technology, Department of Engineering Sciences and Mathematics, SE-971 87 Luleå (Sweden)

2015-12-01

Highlights: • New method: post-modelling of high speed images from a laser-induced front. • From the images a wavy cavity and its absorption distribution is calculated. • Histograms enable additional statistical analysis and understanding. • Despite the complex topology the absorptivity is bound to 35–43%. • The new method visualizes valuable complementary information. - Abstract: Processes like laser keyhole welding, remote fusion laser cutting or laser drilling are governed by a highly dynamic wavy boiling front that was recently recorded by ultra-high speed imaging. A new approach has now been established by post-modelling of the high speed images. Based on the image greyscale and on a cavity model the three-dimensional front topology is reconstructed. As a second step the Fresnel absorptivity modulation across the wavy front is calculated, combined with the local projection of the laser beam. Frequency polygons enable additional analysis of the statistical variations of the properties across the front. Trends like shadow formation and time dependency can be studied, locally and for the whole front. Despite strong topology modulation in space and time, for lasers with 1 μm wavelength and steel the absorptivity is bounded to a narrow range of 35–43%, owing to its Fresnel characteristics.

Google-Earth Based Visualizations for Environmental Flows and Pollutant Dispersion in Urban Areas

Directory of Open Access Journals (Sweden)

Daoming Liu

2017-03-01

Full Text Available In the present study, we address the development and application of an efficient tool for conversion of results obtained by an integrated computational fluid dynamics (CFD and computational reaction dynamics (CRD approach and their visualization in the Google Earth. We focus on results typical for environmental fluid mechanics studies at a city scale that include characteristic wind flow patterns and dispersion of reactive scalars. This is achieved by developing a code based on the Java language, which converts the typical four-dimensional structure (spatial and temporal dependency of data results in the Keyhole Markup Language (KML format. The visualization techniques most often used are revisited and implemented into the conversion tool. The potential of the tool is demonstrated in a case study of smog formation due to an intense traffic emission in Rotterdam (The Netherlands. It is shown that the Google Earth can provide a computationally efficient and user-friendly means of data representation. This feature can be very useful for visualization of pollution at street levels, which is of great importance for the city residents. Various meteorological and traffic emissions can be easily visualized and analyzed, providing a powerful, user-friendly tool for traffic regulations and urban climate adaptations.

Molecular approach of uranyl/mineral surfaces: experimental approach

International Nuclear Information System (INIS)

Drot, R.

2009-01-01

The author reports an experimental approach in which different spectroscopic approaches are coupled (laser spectroscopy, X-ray absorption spectroscopy, vibrational spectroscopy) to investigate the mechanisms controlling actinide sorption processes by different substrates, in order to assess radioactive waste storage site safety. Different substrates have been considered: monocrystalline or powdered TiO 2 , montmorillonite, and gibbsite

Molecular eigenstate spectroscopy: Application to the intramolecular dynamics of some polyatomic molecules in the 3000 to 7000 cm-1 region

International Nuclear Information System (INIS)

Perry, D.S.

1991-05-01

This project uses high resolution infrared spectroscopy to probe the mechanism of intramolecular vibrational redistribution (IVR) in isolated polyatomic molecules. We have found only vibrationally anharmonic coupling in the C-H stretch region of 1-butyne but rotationally mediated coupling is evident in similar spectra of ethanol. The ''keyhole'' model of IVR was developed to account for the similarities and differences between these molecules. The concepts of the model are being implemented numerically in random matrix calculations. A second F-center laser has been purchased and is now being set up to develop an infrared double resonance technique which can be applied to this problem. 4 refs., 5 figs

Development of a fatigue analysis software system

International Nuclear Information System (INIS)

Choi, B. I.; Lee, H. J.; Han, S. W.; Kim, J. Y.; Hwang, K. H.; Kang, J. Y.

2001-01-01

A general purpose fatigue analysis software to predict fatigue lives of mechanical components and structures was developed. This software has some characteristic features including functions of searching weak regions on the free surface in order to reduce computing time significantly, a database of fatigue properties for various materials, and an expert system which can assist any users to get more proper results. This software can be used in the environment consists of commercial finite element packages. Using the software developed fatigue analyses for a SAE keyhole specimen and an automobile knuckle were carried out. It was observed that the results were agree well with those from commercial packages

Micro-Welding of Copper Plate by Frequency Doubled Diode Pumped Pulsed Nd:YAG Laser

Science.gov (United States)

Nakashiba, Shin-Ichi; Okamoto, Yasuhiro; Sakagawa, Tomokazu; Takai, Sunao; Okada, Akira

A pulsed laser of 532 nm wavelength with ms range pulse duration was newly developed by second harmonic generation of diode pumped pulsed Nd:YAG laser. High electro-optical conversion efficiency more than 13% could be achieved, and 1.5 kW peak power green laser pulse was put in optical fiber of 100 μm in diameter. In micro- welding of 1.0 mm thickness copper plate, a keyhole welding was successfully performed by 1.0 kW peak power at spot diameter less than 200 μm. The frequency doubled pulsed laser improved the processing efficiency of copper welding, and narrow and deep weld bead was stably obtained.

Fracture Mechanics Evaluation of B-1 Materials. Volume I. Text

Science.gov (United States)

1976-10-01

4V Microstructures 2-37 P.4-1 TIG Welding Setup 2-60 2.4-2 Macrographs Showing Transverse Cross- 2-61 Sections of Typical Weld Joints 2.4-3 Diffusion...concavity. k. PAW welding parameters were: Keyhole Mode (First Pass) 1fWelding-Amperage - 185 Pilot Arc Amperage - P5 1/5" Diameter Tungsten -P% Thoria...of tooling employed. 2. •𔃼󈧿 r a • 4 .fA A A ~ . - 4N. I 141Eb,~..0 1171 :41ýI t4, 1. r "I j, O~ vN;I ___4 A Ad2 Figuire 2.4-1i TIG Welding , Setup

A reliable method for reconstituting thymectomized, lethally irradiated guinea pigs with bone marrow cells

International Nuclear Information System (INIS)

Terata, N.; Tanio, Y.; Zbar, B.

1984-01-01

The authors developed a reliable method for reconstituting thymectomized, lethally irradiated guinea pigs. Injection of 2.5-10 x 10 7 syngeneic bone marrow cells into adult thymectomized, lethally irradiated guinea pigs produced survival of 46-100% of treated animals. Gentamycin sulfate (5 mg/kg of body weight) for 10 days was required for optimal results. Acidified drinking water (pH 2.5) appeared to be required for optimal results. Thymectomized, lethally irradiated, bone marrow reconstituted ('B') guinea pigs had impaired ability to develop delayed cutaneous hypersensitivity to mycobacterial antigens and cutaneous basophil hypersensitivity to keyhole limpet hemocyanin; proliferative responses to phytohemagglutinin were impaired. (Auth.)

MBO: A Rational Approach and a Comparative Frameworks Approach

Science.gov (United States)

Harries, T. W.

1974-01-01

Considering an organizational phenomenon from more than one theoretical perspective may be more fruitful than using a single rational approach. There is a danger that the restriction of information generation caused by the single approach may produce a false certainty engendered in part through the methodology itself. (Author/WM)

PROCESS-GENRE APPROACH, PRODUCT APPROACH, AND STUDENTS’ SELF-ESTEEM IN TEACHING WRITING

Directory of Open Access Journals (Sweden)

M. Ali Ghufron

2016-07-01

Full Text Available This research was aimed at revealing whether or not: (1 process-genre approach is more effective than product approach in teaching writing; (2 students who have high self-esteem have better writing skill than those who have low self-esteem; and (3 there is an interaction between teaching-learning approaches and students’ self-esteem in teaching writing. This experimental research involved two classes of third semester students of English Education Study Program of IKIP PGRI Bojonegoro. Each class consisted of 38 students. The writing test and questionnaire on self-esteem were used as the instruments to collect the data of this research. The results show that: (1 Process-Genre Approach is more effective than Product Approach in teaching writing; (2 the students who have high self-esteem have better writing skill than those who have low self-esteem; and (3 there is an interaction between teaching approaches and the students’ self-esteem in teaching writing. Therefore, it is suggested to implement Process-Genre Approach since the students can experience every stage of writing process in order to deliver the message in their writing properly.

Process-Genre Approach, Product Approach, and Students’ Self-Esteem in Teaching Writing

Directory of Open Access Journals (Sweden)

M. Ali Ghufron

2016-07-01

Full Text Available This research was aimed at revealing whether or not: (1 process-genre approach is more effective than product approach in teaching writing; (2 students who have high self-esteem have better writing skill than those who have low self-esteem; and (3 there is an interaction between teaching-learning approaches and students’ self-esteem in teaching writing. This experimental research involved two classes of third semester students of English Education Study Program of IKIP PGRI Bojonegoro. Each class consisted of 38 students. The writing test and questionnaire on self-esteem were used as the instruments to collect the data of this research. The results show that: (1 Process-Genre Approach is more effective than Product Approach in teaching writing; (2 the students who have high self-esteem have better writing skill than those who have low self-esteem; and (3 there is an interaction between teaching approaches and the students’ self-esteem in teaching writing. Therefore, it is suggested to implement Process-Genre Approach since the students can experience every stage of writing process in order to deliver the message in their writing properly.

The transformativity approach

DEFF Research Database (Denmark)

Holm, Isak Winkel; Lauta, Kristian Cedervall

2017-01-01

During the last five to ten years, a considerable body of research has begun to explore how disasters, real and imagined, trigger social transformations. Even if the contributions to this this research stems from a multitude of academic disciplines, we argue in the article, they constitute...... an identifiable and promising approach for future disaster research. We suggest naming it the transformativity approach. Whereas the vulnerability approach explores the social causation of disasters, the transformativity approach reverses the direction of the gaze and investigates the social transformation...... brought about by disasters. Put simply, the concept of vulnerability is about the upstream causes of disaster and the concept of transformativity about the downstream effects. By discussing three recent contributions (by the historian Greg Bankoff, the legal sociologist Michelle Dauber...

Life Span Developmental Approach

OpenAIRE

Ali Eryilmaz

2011-01-01

The Life Span Developmental Approach examines development of individuals which occurs from birth to death. Life span developmental approach is a multi-disciplinary approach related with disciplines like psychology, psychiatry, sociology, anthropology and geriatrics that indicates the fact that development is not completed in adulthood, it continues during the life course. Development is a complex process that consists of dying and death. This approach carefully investigates the development of...

Life Span Developmental Approach

Directory of Open Access Journals (Sweden)

Ali Eryilmaz

2011-03-01

Full Text Available The Life Span Developmental Approach examines development of individuals which occurs from birth to death. Life span developmental approach is a multi-disciplinary approach related with disciplines like psychology, psychiatry, sociology, anthropology and geriatrics that indicates the fact that development is not completed in adulthood, it continues during the life course. Development is a complex process that consists of dying and death. This approach carefully investigates the development of individuals with respect to developmental stages. This developmental approach suggests that scientific disciplines should not explain developmental facts only with age changes. Along with aging, cognitive, biological, and socioemotional development throughout life should also be considered to provide a reasonable and acceptable context, guideposts, and reasonable expectations for the person. There are three important subjects whom life span developmental approach deals with. These are nature vs nurture, continuity vs discontinuity, and change vs stability. Researchers using life span developmental approach gather and produce knowledge on these three most important domains of individual development with their unique scientific methodology.

Exploitation rates of two benthic resources across management regimes in central Chile: Evidence of illegal fishing in artisanal fisheries operating in open access areas

Science.gov (United States)

Andreu-Cazenave, Miguel; Subida, Maria Dulce; Fernandez, Miriam

2017-01-01

There is an urgent need to quantify the impacts of artisanal fisheries and define management practices that allow for the recovery and conservation of exploited stocks. The extent of illegal catch is particularly critical as a driver of overexploitation in artisanal fisheries. However, the lack of data at proper spatial scales limits the evaluation of illegal fishing and effectiveness of management practices. We used a catch curve analysis to estimate total instantaneous mortality as a proxy of fishing pressure in the artisanal benthic fishery in central Chile. We compared the patterns of total mortality in fishing grounds under the well-studied territorial use rights for fisheries system (TURF) immersed in a landscape of open access areas (OAA; no access restriction), and from these patterns determined the extent of illegal fishing in open access areas focusing on the two most frequently extracted resources: locos (Concholepas concholepas) and keyhole limpets (Fissurella spp.). The beauty of this seascape is the presence of the no-take (NT) area of Las Cruces as control (no fishing), allowing us to estimate natural mortality. Loco exploitation is banned in OAAs. However, loco mortality in OAAs was 92% higher than in the NT, and 42% higher than in TURFs. Keyhole limpet mortality was similar between TURFs and the NT, but doubled in OAAs. We also found strong differences in mortality among fishing grounds with the same level of protection (i.e. TURFs), and over time. Our results highlight (a) the high level of illegal fishing that may occur in artisanal fisheries under traditional management regimes, and (b) that TURFs can be effective to reduce fishing mortality. However, large variability among TURFs suggests the need for a deeper understanding of the drivers of success of TURFs. PMID:28666013

Hemocyanins Stimulate Innate Immunity by Inducing Different Temporal Patterns of Proinflammatory Cytokine Expression in Macrophages.

Science.gov (United States)

Zhong, Ta-Ying; Arancibia, Sergio; Born, Raimundo; Tampe, Ricardo; Villar, Javiera; Del Campo, Miguel; Manubens, Augusto; Becker, María Inés

2016-06-01

Hemocyanins induce a potent Th1-dominant immune response with beneficial clinical outcomes when used as a carrier/adjuvant in vaccines and nonspecific immunostimulant in cancer. However, the mechanisms by which hemocyanins trigger innate immune responses, leading to beneficial adaptive immune responses, are unknown. This response is triggered by a proinflammatory signal from various components, of which macrophages are an essential part. To understand how these proteins influence macrophage response, we investigated the effects of mollusks hemocyanins with varying structural and immunological properties, including hemocyanins from Concholepas concholepas, Fissurella latimarginata, and Megathura crenulata (keyhole limpet hemocyanin), on cultures of peritoneal macrophages. Hemocyanins were phagocytosed and slowly processed. Analysis of this process showed differential gene expression along with protein levels of proinflammatory markers, including IL-1β, IL-6, IL-12p40, and TNF-α. An extended expression analysis of 84 cytokines during a 24-h period showed a robust proinflammatory response for F. latimarginata hemocyanin in comparison with keyhole limpet hemocyanin and C. concholepas hemocyanin, which was characterized by an increase in the transcript levels of M1 cytokines involved in leukocyte recruitment. These cytokine genes included chemokines (Cxcl1, Cxcl3, Cxcl5, Ccl2, and Ccl3), ILs (Il1b and Ifng), growth factors (Csf2 and Csf3), and TNF family members (Cd40lg). The protein levels of certain cytokines were increased. However, every hemocyanin maintains downregulated key M2 cytokine genes, including Il4 and Il5 Collectively, our data demonstrate that hemocyanins are able to trigger the release of proinflammatory factors with different patterns of cytokine expression, suggesting differential signaling pathways and transcriptional network mechanisms that lead to the activation of M1-polarized macrophages. Copyright © 2016 by The American Association of

Exploitation rates of two benthic resources across management regimes in central Chile: Evidence of illegal fishing in artisanal fisheries operating in open access areas.

Science.gov (United States)

Andreu-Cazenave, Miguel; Subida, Maria Dulce; Fernandez, Miriam

2017-01-01

There is an urgent need to quantify the impacts of artisanal fisheries and define management practices that allow for the recovery and conservation of exploited stocks. The extent of illegal catch is particularly critical as a driver of overexploitation in artisanal fisheries. However, the lack of data at proper spatial scales limits the evaluation of illegal fishing and effectiveness of management practices. We used a catch curve analysis to estimate total instantaneous mortality as a proxy of fishing pressure in the artisanal benthic fishery in central Chile. We compared the patterns of total mortality in fishing grounds under the well-studied territorial use rights for fisheries system (TURF) immersed in a landscape of open access areas (OAA; no access restriction), and from these patterns determined the extent of illegal fishing in open access areas focusing on the two most frequently extracted resources: locos (Concholepas concholepas) and keyhole limpets (Fissurella spp.). The beauty of this seascape is the presence of the no-take (NT) area of Las Cruces as control (no fishing), allowing us to estimate natural mortality. Loco exploitation is banned in OAAs. However, loco mortality in OAAs was 92% higher than in the NT, and 42% higher than in TURFs. Keyhole limpet mortality was similar between TURFs and the NT, but doubled in OAAs. We also found strong differences in mortality among fishing grounds with the same level of protection (i.e. TURFs), and over time. Our results highlight (a) the high level of illegal fishing that may occur in artisanal fisheries under traditional management regimes, and (b) that TURFs can be effective to reduce fishing mortality. However, large variability among TURFs suggests the need for a deeper understanding of the drivers of success of TURFs.

Exploitation rates of two benthic resources across management regimes in central Chile: Evidence of illegal fishing in artisanal fisheries operating in open access areas.

Directory of Open Access Journals (Sweden)

Miguel Andreu-Cazenave

Full Text Available There is an urgent need to quantify the impacts of artisanal fisheries and define management practices that allow for the recovery and conservation of exploited stocks. The extent of illegal catch is particularly critical as a driver of overexploitation in artisanal fisheries. However, the lack of data at proper spatial scales limits the evaluation of illegal fishing and effectiveness of management practices. We used a catch curve analysis to estimate total instantaneous mortality as a proxy of fishing pressure in the artisanal benthic fishery in central Chile. We compared the patterns of total mortality in fishing grounds under the well-studied territorial use rights for fisheries system (TURF immersed in a landscape of open access areas (OAA; no access restriction, and from these patterns determined the extent of illegal fishing in open access areas focusing on the two most frequently extracted resources: locos (Concholepas concholepas and keyhole limpets (Fissurella spp.. The beauty of this seascape is the presence of the no-take (NT area of Las Cruces as control (no fishing, allowing us to estimate natural mortality. Loco exploitation is banned in OAAs. However, loco mortality in OAAs was 92% higher than in the NT, and 42% higher than in TURFs. Keyhole limpet mortality was similar between TURFs and the NT, but doubled in OAAs. We also found strong differences in mortality among fishing grounds with the same level of protection (i.e. TURFs, and over time. Our results highlight (a the high level of illegal fishing that may occur in artisanal fisheries under traditional management regimes, and (b that TURFs can be effective to reduce fishing mortality. However, large variability among TURFs suggests the need for a deeper understanding of the drivers of success of TURFs.

Remote automatic plasma arc-closure welding of a dry-storage canister for spent nuclear fuel and high-level radioactive waste

International Nuclear Information System (INIS)

Sprecace, R.P.; Blankenship, W.P.

1982-01-01

A carbon steel storage canister has been designed for the dry encapsulation of spent nuclear fuel assemblies or of logs of vitrified high level radioactive waste. The canister design is in conformance with the requirements of the ASME Code, Section III, Division 1 for a Class 3 vessel. The canisters will be loaded and sealed as part of a completely remote process sequence to be performed in the hot bay of an experimental encapsulation facility at the Nevada Test Site. The final closure to be made is a full penetration butt weld between the canister body, a 12.75-in O.D. x 0.25-in wall pipe, and a mating semiellipsoidal closure lid. Due to a combination of design, application and facility constraints, the closure weld must be made in the 2G position (canister vertical). The plasma arc welding system is described, and the final welding procedure is described and discussed in detail. Several aspects and results of the procedure development activity, which are of both specific and general interest, are highlighted; these include: The critical welding torch features which must be exactly controlled to permit reproducible energy input to, and gas stream interaction with, the weld puddle. A comparison of results using automatic arc voltage control with those obtained using a mechanically fixed initial arc gap. The optimization of a keyhole initiation procedure. A comparison of results using an autogenous keyhole closure procedure with those obtained using a filler metal addition. The sensitivity of the welding process and procedure to variations in joint configuration and dimensions and to variations in base metal chemistry. Finally, the advantages and disadvantages of the plasma arc process for this application are summarized from the current viewpoint, and the applicability of this process to other similar applications is briefly indicated

The sustainable livelihoods approach

DEFF Research Database (Denmark)

Oelofse, Myles; Jensen, Henning Høgh

2008-01-01

food chain has on producers and their families, an analysis was conducted of the use of the Sustainable Livelihoods Approach (SLA). The SLA provides a holistic and integrative approach which researchers can use as the overriding frame for their research. The application of the approach is recommended...

Optimization of electrostatic lens systems for low-energy scanning microcolumn applications

International Nuclear Information System (INIS)

Oh, Tae-Sik; Kim, Dae-Wook; Ahn, Seungjoon; Kim, Young Chul; Kim, Ho-Seob; Ahn, Seong Joon

2008-01-01

The optimization of a low-energy scanning microcolumn is proposed by adopting a modified Einzel lens sandwiched between an aligner and a deflector. The modified Einzel lens is composed of four electrodes, and the two center electrodes are specially designed quadrupole lenses having keyhole type rather than circular apertures. The outer electrodes of the Einzel lens having circular apertures are grounded, and the quadrupole lens is operated by applying the quadrupole voltages. The effects of the separated deflector system and the static quadrupole lens were investigated by analyzing the scanning electron beam spot at the target, and the results show that the proposed system can improve the performance of the scanning microcolumn

The Use of Megamelus scutellaris Berg in the Southern United States as a Biocontrol Agent of Waterhyacinth (Eichhornia crassipes (Mart.))

Science.gov (United States)

2014-07-01

90°49󈧓.38"W Keyhole Lake, Bonnet Carré Spillway, LA (Open release) 32°20󈧧.01"N 10/10/2010 200 90°59𔄂.73"W Delta, LA (Open release) 32...28.642’W Lake St. Joseph, LA (Single cage) 31°54󈧎.43"N 9/15/2011 200 91°14󈧡.99"W TOTAL 2011 9,400 Gramercy, LA (Two cages in close ...proximity) 30°11𔃽.48" N 6/12/2012 625 (Range 500- 750) 90°48󈧻.45"W Alligator Bayou, LA (Two cages in close proximity) 30°18’31.46”N 6/12

What you see is what you buy

DEFF Research Database (Denmark)

Orquin, Jacob Lund; Scholderer, Joachim; Jeppesen, H.B.

reports the findings from an eye-tracking study on consumer attention and product choice. The study revealed that increases in the saliency and surface size of packaging elements are associated with greater fixation likelihood and that attention to elements such as product claims and organic labels......Previous research has shown that increases in the overall saliency of products packages lead to increases in attention and how attention affects choice. However, no studies have addressed this issue at the level of individual packaging elements such as product claims and labels. The present paper...... is associated with increased choice probability whereas attention to nutrition-related elements such as GDA labels or the Nordic keyhole label is associated with decreased choice probability....

Evaluating Six Soft Approaches

DEFF Research Database (Denmark)

Sørensen, Lene Tolstrup; Valqui Vidal, René Victor

2008-01-01

's interactive planning principles to be supported by soft approaches in carrying out the principles in action. These six soft approaches are suitable forsupporting various steps of the strategy development and planning process. These are the SWOT analysis, the Future Workshop, the Scenario methodology......, Strategic Option Development and Analysis, Strategic Choice Approach and Soft Systems Methodology. Evaluations of each methodology are carried out using a conceptual framework in which the organisation, the result, the process and the technology of the specific approach are taken into consideration. Using...

Evaluating six soft approaches

DEFF Research Database (Denmark)

Sørensen, Lene Tolstrup; Vidal, Rene Victor Valqui

2008-01-01

's interactive planning principles to be supported by soft approaches in carrying out the principles in action. These six soft approaches are suitable forsupporting various steps of the strategy development and planning process. These are the SWOT analysis, the Future Workshop, the Scenario methodology......, Strategic Option Development and Analysis, Strategic Choice Approach and Soft Systems Methodology. Evaluations of each methodology are carried out using a conceptual framework in which the organisation, the result, the process and the technology of the specific approach are taken into consideration. Using...

When opportunity meets motivation: Neural engagement during social approach is linked to high approach motivation.

Science.gov (United States)

Radke, Sina; Seidel, Eva-Maria; Eickhoff, Simon B; Gur, Ruben C; Schneider, Frank; Habel, Ute; Derntl, Birgit

2016-02-15

Social rewards are processed by the same dopaminergic-mediated brain networks as non-social rewards, suggesting a common representation of subjective value. Individual differences in personality and motivation influence the reinforcing value of social incentives, but it remains open whether the pursuit of social incentives is analogously supported by the neural reward system when positive social stimuli are connected to approach behavior. To test for a modulation of neural activation by approach motivation, individuals with high and low approach motivation (BAS) completed implicit and explicit social approach-avoidance paradigms during fMRI. High approach motivation was associated with faster implicit approach reactions as well as a trend for higher approach ratings, indicating increased approach tendencies. Implicit and explicit positive social approach was accompanied by stronger recruitment of the nucleus accumbens, middle cingulate cortex, and (pre-)cuneus for individuals with high compared to low approach motivation. These results support and extend prior research on social reward processing, self-other distinctions and affective judgments by linking approach motivation to the engagement of reward-related circuits during motivational reactions to social incentives. This interplay between motivational preferences and motivational contexts might underlie the rewarding experience during social interactions. Copyright © 2015 Elsevier Inc. All rights reserved.

Stuttering-Psycholinguistic Approach

Science.gov (United States)

Hategan, Carolina Bodea; Anca, Maria; Prihoi, Lacramioara

2012-01-01

This research promotes psycholinguistic paradigm, it focusing in delimitating several specific particularities in stuttering pathology. Structural approach, on language sides proves both the recurrent aspects found within specialized national and international literature and the psycholinguistic approaches dependence on the features of the…

Evaluating six soft approaches

DEFF Research Database (Denmark)

Sørensen, Lene; Vidal, Rene Victor Valqui

2006-01-01

’s interactive planning principles to be supported by soft approaches in carrying out the principles in action. These six soft approaches are suitable for supporting various steps of the strategy development and planning process. These are the SWOT analysis, the Future Workshop, the Scenario methodology......, Strategic Option Development and Analysis, Strategic Choice Approach and Soft Systems Methodology. Evaluations of each methodology are carried out using a conceptual framework in which the organisation, the result, the process and the technology of the specific approach are taken into consideration. Using...

The Geodynamic Approach

DEFF Research Database (Denmark)

Steenfelt, Jørgen S.; Ibsen, Lars Bo

1996-01-01

The Danish National lecture: The Geodynamic approach - problem or possibility? - mirrors the authors involvement in projects and research focusing on the impact of the geodynamic approach. The lecture discusses the why and how of some of the geotechnical anomalies and the differences in traditional...

Neuroscience and approach/avoidance personality traits: a two stage (valuation-motivation) approach.

Science.gov (United States)

Corr, Philip J; McNaughton, Neil

2012-11-01

Many personality theories link specific traits to the sensitivities of the neural systems that control approach and avoidance. But there is no consensus on the nature of these systems. Here we combine recent advances in economics and neuroscience to provide a more solid foundation for a neuroscience of approach/avoidance personality. We propose a two-stage integration of valuation (loss/gain) sensitivities with motivational (approach/avoidance/conflict) sensitivities. Our key conclusions are: (1) that valuation of appetitive and aversive events (e.g. gain and loss as studied by behavioural economists) is an independent perceptual input stage--with the economic phenomenon of loss aversion resulting from greater negative valuation sensitivity compared to positive valuation sensitivity; (2) that valuation of an appetitive stimulus then interacts with a contingency of presentation or omission to generate a motivational 'attractor' or 'repulsor', respectively (vice versa for an aversive stimulus); (3) the resultant behavioural tendencies to approach or avoid have distinct sensitivities to those of the valuation systems; (4) while attractors and repulsors can reinforce new responses they also, more usually, elicit innate or previously conditioned responses and so the perception/valuation-motivation/action complex is best characterised as acting as a 'reinforcer' not a 'reinforcement'; and (5) approach-avoidance conflict must be viewed as activating a third motivation system that is distinct from the basic approach and avoidance systems. We provide examples of methods of assessing each of the constructs within approach-avoidance theories and of linking these constructs to personality measures. We sketch a preliminary five-element reinforcer sensitivity theory (RST-5) as a first step in the integration of existing specific approach-avoidance theories into a coherent neuroscience of personality. Copyright © 2012 Elsevier Ltd. All rights reserved.

Advanced intelligence and mechanism approach

Institute of Scientific and Technical Information of China (English)

ZHONG Yixin

2007-01-01

Advanced intelligence will feature the intelligence research in next 50 years.An understanding of the concept of advanced intelligence as well as its importance will be provided first,and detailed analysis on an approach,the mechanism approach.suitable to the advanced intelligence research will then be flolowed.And the mutual relationship among mechanism approach,traditional approaches existed in artificial intelligence research,and the cognitive informatics will be discussed.It is interesting to discover that mechanism approach is a good one to the Advanced Intelligence research and a tmified form of the existed approaches to artificial intelligence.

Introducing Systems Approaches

Science.gov (United States)

Reynolds, Martin; Holwell, Sue

Systems Approaches to Managing Change brings together five systems approaches to managing complex issues, each having a proven track record of over 25 years. The five approaches are: System Dynamics (SD) developed originally in the late 1950s by Jay Forrester Viable Systems Model (VSM) developed originally in the late 1960s by Stafford Beer Strategic Options Development and Analysis (SODA: with cognitive mapping) developed originally in the 1970s by Colin Eden Soft Systems Methodology (SSM) developed originally in the 1970s by Peter Checkland Critical Systems Heuristics (CSH) developed originally in the late 1970s by Werner Ulrich

Understanding the Steiner Waldorf Approach: Early Years Education in Practice. Understanding the... Approach

Science.gov (United States)

Nicol, Janni; Taplin, Jill

2012-01-01

Understanding the Steiner Waldorf Approach is a much needed source of information for those wishing to extend and consolidate their understanding of the Steiner Waldorf High Scope Approach. It will enable the reader to analyse the essential elements of the Steiner Waldorf Approach to early childhood and its relationship to quality early years…

Flipped Classroom Approach

Science.gov (United States)

Ozdamli, Fezile; Asiksoy, Gulsum

2016-01-01

Flipped classroom is an active, student-centered approach that was formed to increase the quality of period within class. Generally this approach whose applications are done mostly in Physical Sciences, also attracts the attention of educators and researchers in different disciplines recently. Flipped classroom learning which wide-spreads rapidly…

Technical approach document

International Nuclear Information System (INIS)

1989-12-01

The Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law 95-604 (PL95-604), grants the Secretary of Energy the authority and responsibility to perform such actions as are necessary to minimize radiation health hazards and other environmental hazards caused by inactive uranium mill sites. This Technical Approach Document (TAD) describes the general technical approaches and design criteria adopted by the US Department of Energy (DOE) in order to implement remedial action plans (RAPS) and final designs that comply with EPA standards. It does not address the technical approaches necessary for aquifer restoration at processing sites; a guidance document, currently in preparation, will describe aquifer restoration concerns and technical protocols. This document is a second revision to the original document issued in May 1986; the revision has been made in response to changes to the groundwater standards of 40 CFR 192, Subparts A--C, proposed by EPA as draft standards. New sections were added to define the design approaches and designs necessary to comply with the groundwater standards. These new sections are in addition to changes made throughout the document to reflect current procedures, especially in cover design, water resources protection, and alternate site selection; only minor revisions were made to some of the sections. Sections 3.0 is a new section defining the approach taken in the design of disposal cells; Section 4.0 has been revised to include design of vegetated covers; Section 8.0 discusses design approaches necessary for compliance with the groundwater standards; and Section 9.0 is a new section dealing with nonradiological hazardous constituents. 203 refs., 18 figs., 26 tabs

Flipped Classroom Approach

Directory of Open Access Journals (Sweden)

Fezile Ozdamli

2016-07-01

Full Text Available Flipped classroom is an active, student-centered approach that was formed to increase the quality of period within class. Generally this approach whose applications are done mostly in Physical Sciences, also attracts the attention of educators and researchers in different disciplines recently. Flipped classroom learning which wide-spreads rapidly in the world, is not well recognized in our country. That is why the aim of study is to attract attention to its potential in education field and provide to make it recognize more by educators and researchers. With this aim, in the study what flipped classroom approach is, flipped classroom technology models, its advantages and limitations were explained.

An investigation on capability of hybrid Nd:YAG laser-TIG welding technology for AA2198 Al-Li alloy

Science.gov (United States)

Faraji, Amir Hosein; Moradi, Mahmoud; Goodarzi, Massoud; Colucci, Pietro; Maletta, Carmine

2017-09-01

This paper surveys the capability of the hybrid laser-arc welding in comparison with lone laser welding for AA2198 aluminum alloy experimentally. In the present research, a continuous Nd:YAG laser with a maximum power of 2000 W and a 350 A electric arc were used as two combined welding heat sources. In addition to the lone laser welding experiments, two strategies were examined for hybrid welding; the first one was low laser power (100 W) accompanied by high arc energy, and the second one was high laser power (2000 W) with low arc energy. Welding speed and arc current varied in the experiments. The influence of heat input on weld pool geometry was surveyed. The macrosection, microhardness profile and microstructure of the welded joints were studied and compared. The results indicated that in lone laser welding, conduction mode occurred and keyhole was not formed even in low welding speeds and thus the penetration depth was so low. It was also found that the second approach (high laser power accompanied with low arc energy) is superior to the first one (low laser power accompanied with high arc energy) in hybrid laser-arc welding of Al2198, since lower heat input was needed for full penetration weld and as a result a smaller HAZ was created.

Analysis of laser remote fusion cutting based on a mathematical model

Energy Technology Data Exchange (ETDEWEB)

Matti, R. S. [Department of Engineering Sciences and Mathematics, Luleå University of Technology, S-971 87 Luleå (Sweden); Department of Mechanical Engineering, College of Engineering, University of Mosul, Mosul (Iraq); Ilar, T.; Kaplan, A. F. H. [Department of Engineering Sciences and Mathematics, Luleå University of Technology, S-971 87 Luleå (Sweden)

2013-12-21

Laser remote fusion cutting is analyzed by the aid of a semi-analytical mathematical model of the processing front. By local calculation of the energy balance between the absorbed laser beam and the heat losses, the three-dimensional vaporization front can be calculated. Based on an empirical model for the melt flow field, from a mass balance, the melt film and the melting front can be derived, however only in a simplified manner and for quasi-steady state conditions. Front waviness and multiple reflections are not modelled. The model enables to compare the similarities, differences, and limits between laser remote fusion cutting, laser remote ablation cutting, and even laser keyhole welding. In contrast to the upper part of the vaporization front, the major part only slightly varies with respect to heat flux, laser power density, absorptivity, and angle of front inclination. Statistical analysis shows that for high cutting speed, the domains of high laser power density contribute much more to the formation of the front than for low speed. The semi-analytical modelling approach offers flexibility to simplify part of the process physics while, for example, sophisticated modelling of the complex focused fibre-guided laser beam is taken into account to enable deeper analysis of the beam interaction. Mechanisms like recast layer generation, absorptivity at a wavy processing front, and melt film formation are studied too.

Analysis of laser remote fusion cutting based on a mathematical model

International Nuclear Information System (INIS)

Matti, R. S.; Ilar, T.; Kaplan, A. F. H.

2013-01-01

Laser remote fusion cutting is analyzed by the aid of a semi-analytical mathematical model of the processing front. By local calculation of the energy balance between the absorbed laser beam and the heat losses, the three-dimensional vaporization front can be calculated. Based on an empirical model for the melt flow field, from a mass balance, the melt film and the melting front can be derived, however only in a simplified manner and for quasi-steady state conditions. Front waviness and multiple reflections are not modelled. The model enables to compare the similarities, differences, and limits between laser remote fusion cutting, laser remote ablation cutting, and even laser keyhole welding. In contrast to the upper part of the vaporization front, the major part only slightly varies with respect to heat flux, laser power density, absorptivity, and angle of front inclination. Statistical analysis shows that for high cutting speed, the domains of high laser power density contribute much more to the formation of the front than for low speed. The semi-analytical modelling approach offers flexibility to simplify part of the process physics while, for example, sophisticated modelling of the complex focused fibre-guided laser beam is taken into account to enable deeper analysis of the beam interaction. Mechanisms like recast layer generation, absorptivity at a wavy processing front, and melt film formation are studied too

Theoretical Approaches to Coping

Directory of Open Access Journals (Sweden)

Sofia Zyga

2013-01-01

Full Text Available Introduction: Dealing with stress requires conscious effort, it cannot be perceived as equal to individual's spontaneous reactions. The intentional management of stress must not be confused withdefense mechanisms. Coping differs from adjustment in that the latter is more general, has a broader meaning and includes diverse ways of facing a difficulty.Aim: An exploration of the definition of the term "coping", the function of the coping process as well as its differentiation from other similar meanings through a literature review.Methodology: Three theoretical approaches of coping are introduced; the psychoanalytic approach; approaching by characteristics; and the Lazarus and Folkman interactive model.Results: The strategic methods of the coping approaches are described and the article ends with a review of the approaches including the functioning of the stress-coping process , the classificationtypes of coping strategies in stress-inducing situations and with a criticism of coping approaches.Conclusions: The comparison of coping in different situations is difficult, if not impossible. The coping process is a slow process, so an individual may select one method of coping under one set ofcircumstances and a different strategy at some other time. Such selection of strategies takes place as the situation changes.

Pedagogical approaches

DEFF Research Database (Denmark)

Lund Larsen, Lea

questions are: How (much) and what do teachers learn from experience? And how do teachers of adults develop their pedagogical approach? I examine the field of adult learners from the teachers’ perspective. Firstly, I identify some of the commonly described characteristics of adults as learners...... in formal settings, but in most teaching settings, the teachers act alone and develop their pedagogical approaches/- teaching strategies with no synchronous sparring from a colleague. Adult learners have particular needs and characteristics that their teachers must be able to address (cf. Knowles...

A Janus-Faced Approach to Learning. A Critical Discussion of Habermas' Pragmatic Approach

Science.gov (United States)

Italia, Salvatore

2017-01-01

A realist approach to learning is what I propose here. This is based on a non-epistemic dimension whose presence is a necessary assumption for a concept of learning of a life-world as complementary to learning within a life-world. I develop my approach in opposition to Jürgen Habermas' pragmatic approach, which seems to lack of something from a…

Approaches to quantum gravity. Loop quantum gravity, spinfoams and topos approach

International Nuclear Information System (INIS)

Flori, Cecilia

2010-01-01

One of the main challenges in theoretical physics over the last five decades has been to reconcile quantum mechanics with general relativity into a theory of quantum gravity. However, such a theory has been proved to be hard to attain due to i) conceptual difficulties present in both the component theories (General Relativity (GR) and Quantum Theory); ii) lack of experimental evidence, since the regimes at which quantum gravity is expected to be applicable are far beyond the range of conceivable experiments. Despite these difficulties, various approaches for a theory of Quantum Gravity have been developed. In this thesis we focus on two such approaches: Loop Quantum Gravity and the Topos theoretic approach. The choice fell on these approaches because, although they both reject the Copenhagen interpretation of quantum theory, their underpinning philosophical approach to formulating a quantum theory of gravity are radically different. In particular LQG is a rather conservative scheme, inheriting all the formalism of both GR and Quantum Theory, as it tries to bring to its logical extreme consequences the possibility of combining the two. On the other hand, the Topos approach involves the idea that a radical change of perspective is needed in order to solve the problem of quantum gravity, especially in regard to the fundamental concepts of 'space' and 'time'. Given the partial successes of both approaches, the hope is that it might be possible to find a common ground in which each approach can enrich the other. This thesis is divided in two parts: in the first part we analyse LQG, paying particular attention to the semiclassical properties of the volume operator. Such an operator plays a pivotal role in defining the dynamics of the theory, thus testing its semiclassical limit is of uttermost importance. We then proceed to analyse spin foam models (SFM), which are an attempt at a covariant or path integral formulation of canonical Loop Quantum Gravity (LQG). In

Approaches to quantum gravity. Loop quantum gravity, spinfoams and topos approach

Energy Technology Data Exchange (ETDEWEB)

Flori, Cecilia

2010-07-23

One of the main challenges in theoretical physics over the last five decades has been to reconcile quantum mechanics with general relativity into a theory of quantum gravity. However, such a theory has been proved to be hard to attain due to i) conceptual difficulties present in both the component theories (General Relativity (GR) and Quantum Theory); ii) lack of experimental evidence, since the regimes at which quantum gravity is expected to be applicable are far beyond the range of conceivable experiments. Despite these difficulties, various approaches for a theory of Quantum Gravity have been developed. In this thesis we focus on two such approaches: Loop Quantum Gravity and the Topos theoretic approach. The choice fell on these approaches because, although they both reject the Copenhagen interpretation of quantum theory, their underpinning philosophical approach to formulating a quantum theory of gravity are radically different. In particular LQG is a rather conservative scheme, inheriting all the formalism of both GR and Quantum Theory, as it tries to bring to its logical extreme consequences the possibility of combining the two. On the other hand, the Topos approach involves the idea that a radical change of perspective is needed in order to solve the problem of quantum gravity, especially in regard to the fundamental concepts of 'space' and 'time'. Given the partial successes of both approaches, the hope is that it might be possible to find a common ground in which each approach can enrich the other. This thesis is divided in two parts: in the first part we analyse LQG, paying particular attention to the semiclassical properties of the volume operator. Such an operator plays a pivotal role in defining the dynamics of the theory, thus testing its semiclassical limit is of uttermost importance. We then proceed to analyse spin foam models (SFM), which are an attempt at a covariant or path integral formulation of canonical Loop Quantum

Solitary Metastasis to the Facial/Vestibulocochlear Nerve Complex: Case Report and Review of the Literature.

Science.gov (United States)

Ariai, M Shafie; Eggers, Scott D; Giannini, Caterina; Driscoll, Colin L W; Link, Michael J

2015-10-01

Distant metastasis of mucinous adenocarcinoma from the gastrointestinal tract, ovaries, pancreas, lungs, breast, or urogenital system is a well-described entity. Mucinous adenocarcinomas from different primary sites are histologically identical with gland cells producing a copious amount of mucin. This report describes a very rare solitary metastasis of a mucinous adenocarcinoma of unknown origin to the facial/vestibulocochlear nerve complex in the cerebellopontine angle. A 71-year-old woman presented with several month history of progressive neurological decline and a negative extensive workup performed elsewhere. She presented to our institution with complete left facial weakness, left-sided deafness, gait unsteadiness, headache and anorexia. A repeat magnetic resonance imaging scan of the head revealed a cystic, enhancing abnormality involving the left cerebellopontine angle and internal auditory canal. A left retrosigmoid craniotomy was performed and the lesion was completely resected. The final pathology was a mucinous adenocarcinoma of indeterminate origin. Postoperatively, the patient continued with her preoperative deficits and subsequently died of her systemic disease 6 weeks after discharge. The facial/vestibulocochlear nerve complex is an unusual location for metastatic disease in the central nervous system. Clinicians should consider metastatic tumor as the possible etiology of an unusual appearing mass in this location causing profound neurological deficits. The prognosis after metastatic mucinous adenocarcinoma to the cranial nerves in the cerebellopontine angle may be poor. Copyright © 2015 Elsevier Inc. All rights reserved.

Approach to team skills training

International Nuclear Information System (INIS)

Koontz, J.L.; Roe, M.L.; Gaddy, C.D.

1987-01-01

The US commercial nuclear power industry has recognized the importance of team skills in control room operation. The desire to combine training of team interaction skills, like communications, with technical knowledge of reactor operations requires a unique approach to training. An NRC-sponsored study identified a five-phase approach to team skills training designed to be consistent with the systems approach to training currently endorsed by the NRC Policy Statement on Training and Qualification. This paper describes an approach to team skills training with emphasis on the nuclear power plant control room crew. An approach to team skills training

Structured Approach vs. Self-Paced Modular Approach in Teaching Trigonometry

Directory of Open Access Journals (Sweden)

Rodin M. Paspasan

2015-12-01

Full Text Available The study aimed to determine which approach in the teaching of Mathematics allowed students to achieve a higher mathematical performance and to establish the learning styles of the students to showed greater confidence on a written posttest - the self-paced modular approach or the structured lecture demonstration based approach. The instruments used in the study are Trigonometry Achievement Test (PTAT designed by the researcher and the Grasha - Reichmann Student Learning Style Survey. Hence. the result shows on the test of significant difference on the respondents learning styles and level of performance established independent learning conditions and demonstrate remarkably higher mathematical performance, respectively. In the light of the statistical analysis and the findings of the study, it could be generalized that SPMA made the students learning styles more independent because they prefer to work at their own pace. Hence, SPMA help them also improve their level of performance in relation to plane trigonometry regardless of their mathematical abilities compared to structured approach. Along these lines, the subsequent recommendations are presented for consideration: The teachers should use collective learning style inventories so that students remain interested throughout their mathematics course. And should use SPMA in teaching trigonometry and other disciplines in the field of mathematics.

Financial Management: An Organic Approach

Science.gov (United States)

Laux, Judy

2013-01-01

Although textbooks present corporate finance using a topical approach, good financial management requires an organic approach that integrates the various assignments financial managers confront every day. Breaking the tasks into meaningful subcategories, the current article offers one approach.

Impact significance determination-Designing an approach

International Nuclear Information System (INIS)

Lawrence, David P.

2007-01-01

The question of how best to go about determining the significance of impacts has, to date, only been addressed in a partial and preliminary way. The assumption tends to be made that it is either only necessary to provide explicit, justified reasons for a judgment about significance and/or to explicitly apply a prescribed procedure-a procedure usually involving the staged application of thresholds and/or criteria. The detailed attributes, strengths and limitations of such approaches and possible alternative approaches have yet to be explored systematically. This article addresses these deficiencies by analyzing the characteristics, specific methods and positive and negative tendencies of three general impact significance determination approaches-the technical approach, the collaborative approach and the reasoned argumentation approach. A range of potential composite approaches are also described. With an enhanced understanding of these approaches, together with potential combinations, EIA practitioners and other EIA participants can be in a better position to select an approach appropriate to their needs, to reinforce the positive tendencies and offset the negative tendencies of the selected approach and to combine the best qualities of more than one approach

The narrative approach to personalisation

Science.gov (United States)

Conlan, Owen; Staikopoulos, Athanasios; Hampson, Cormac; Lawless, Séamus; O'keeffe, Ian

2013-06-01

This article describes the narrative approach to personalisation. This novel approach to the generation of personalised adaptive hypermedia experiences employs runtime reconciliation between a personalisation strategy and a number of contextual models (e.g. user and domain). The approach also advocates the late binding of suitable content and services to the generated personalised pathway resulting in an interactive composition that comprises services as well as content. This article provides a detailed definition of the narrative approach to personalisation and showcases the approach through the examination of two use-cases: the personalised digital educational games developed by the ELEKTRA and 80Days projects; and the personalised learning activities realised as part of the AMAS project. These use-cases highlight the general applicability of the narrative approach and how it has been applied to create a diverse range of real-world systems.

The anterior interhemispheric approach: a safe and effective approach to anterior skull base lesions.

Science.gov (United States)

Mielke, Dorothee; Mayfrank, Lothar; Psychogios, Marios Nikos; Rohde, Veit

2014-04-01

Many approaches to the anterior skull base have been reported. Frequently used are the pterional, the unilateral or bilateral frontobasal, the supraorbital and the frontolateral approach. Recently, endoscopic transnasal approaches have become more popular. The benefits of each approach has to be weighted against its complications and limitations. The aim of this study was to investigate if the anterior interhemispheric approach (AIA) could be a safe and effective alternative approach to tumorous and non-tumorous lesions of the anterior skull base. We screened the operative records of all patients with an anterior skull base lesion undergoing transcranial surgery. We have used the AIA in 61 patients. These were exclusively patients with either olfactory groove meningioma (OGM) (n = 43), ethmoidal dural arteriovenous fistula (dAVF) ( n = 6) or frontobasal fractures of the anterior midline with cerebrospinal fluid (CSF) leakage ( n = 12). Patient records were evaluated concerning accessibility of the lesion, realization of surgical aims (complete tumor removal, dAVF obliteration, closure of the dural tear), and approach related complications. The use of the AIA exclusively in OGMs, ethmoidal dAVFs and midline frontobasal fractures indicated that we considered lateralized frontobasal lesions not suitable to be treated successfully. If restricted to these three pathologies, the AIA is highly effective and safe. The surgical aim (complete tumor removal, complete dAVF occlusion, no rhinorrhea) was achieved in all patients. The complication rate was 11.5 % (wound infection (n = 2; 3.2 %), contusion of the genu of the corpus callosum, subdural hygroma, epileptic seizure, anosmia and asymptomatic bleed into the tumor cavity (n = 1 each). Only the contusion of the corpus callosum was directly related to the approach (1.6 %). Olfaction, if present before surgery, was preserved in all patients, except one (1.6 %). The AIA is an effective and a safe approach

Market-based approaches to tree valuation

Science.gov (United States)

Geoffrey H. Donovan; David T. Butry

2008-01-01

A recent four-part series in Arborist News outlined different appraisal processes used to value urban trees. The final article in the series described the three generally accepted approaches to tree valuation: the sales comparison approach, the cost approach, and the income capitalization approach. The author, D. Logan Nelson, noted that the sales comparison approach...

Strain expansion-reduction approach

Science.gov (United States)

Baqersad, Javad; Bharadwaj, Kedar

2018-02-01

Validating numerical models are one of the main aspects of engineering design. However, correlating million degrees of freedom of numerical models to the few degrees of freedom of test models is challenging. Reduction/expansion approaches have been traditionally used to match these degrees of freedom. However, the conventional reduction/expansion approaches are only limited to displacement, velocity or acceleration data. While in many cases only strain data are accessible (e.g. when a structure is monitored using strain-gages), the conventional approaches are not capable of expanding strain data. To bridge this gap, the current paper outlines a reduction/expansion technique to reduce/expand strain data. In the proposed approach, strain mode shapes of a structure are extracted using the finite element method or the digital image correlation technique. The strain mode shapes are used to generate a transformation matrix that can expand the limited set of measurement data. The proposed approach can be used to correlate experimental and analytical strain data. Furthermore, the proposed technique can be used to expand real-time operating data for structural health monitoring (SHM). In order to verify the accuracy of the approach, the proposed technique was used to expand the limited set of real-time operating data in a numerical model of a cantilever beam subjected to various types of excitations. The proposed technique was also applied to expand real-time operating data measured using a few strain gages mounted to an aluminum beam. It was shown that the proposed approach can effectively expand the strain data at limited locations to accurately predict the strain at locations where no sensors were placed.

STUTTERING-PSYCHOLINGUISTIC APPROACH

OpenAIRE

Maria Anca; Carolina Bodea Haţegan; Lăcrămioara Prihoi

2012-01-01

This research promotes psycholinguistic paradigm, it focusing in delimitating several specific particularities in stuttering pathology. Structural approach, on language sides proves both the recurrent aspects found within specialized national and international literature and the psycholinguistic approaches dependence on the features of the linguistic material. Thus, the conclusions of this research study offer the possibility of promoting cross-cultural and cross-linguistic researches, with t...

Mapping the antigenic structure of porcine parvovirus at the level of peptides

DEFF Research Database (Denmark)

Kamstrup, Søren; Langeveld, Jan; Bøtner, Anette

1998-01-01

The antigenic structure of the capsid proteins of porcine parvovirus (PPV) was investigated. A total of nine linear epitopes were identified by Pepscan using porcine or rabbit anti-PPV antisera. No sites were identified with a panel of neutralising monoclonal antibodies (MAbs). All epitopes were...... located in the region corresponding to the major capsid protein VP2. Based on this information, and on analogy to other autonomous parvoviruses, 24 different peptides were synthesised, coupled to keyhole limpet haemocyanin (KLH) and used to immunise rabbits. Most antisera were able to bind viral protein....... It is concluded that in PPV, the VP2 N-terminus is involved in virus neutralisation (VN) and peptides from this region are therefore primary targets for developing peptide-based vaccines against this virus....

Prenatal diagnosis of prune-belly syndrome at 13 weeks of gestation: case report and review of literature.

Science.gov (United States)

Papantoniou, Nikolaos; Papoutsis, Dimitrios; Daskalakis, Georgios; Chatzipapas, Ioannis; Sindos, Michael; Papaspyrou, Irini; Mesogitis, Spiridon; Antsaklis, Aris

2010-10-01

We present a case report of a foetus with Prune-Belly syndrome (PBS) which was diagnosed sonographically during the 13th week of gestation and review of the literature. Sonographic diagnosis was based on abnormally distended urinary bladder and abdomen and absence of 'keyhole sign'. Termination was performed on parental request and post-mortem examination revealed absence of abdominal wall musculature and the distended urinary bladder in a male foetus. Prenatal diagnosis of PBS is based on ultrasound and is usually diagnosed in the second trimester. In the first trimester there are very few reports to date. Prognosis and possible treatment options are herein discussed as well as the underlying mechanisms that may explain the clinical presentation of the syndrome.

Effect of chlorphenesin on localized hemolysis in gel assay.

Science.gov (United States)

Fukui, G M; Berger, F M; Chandlee, G C; Goldenbaum, E G

1968-10-01

Chlorphenesin, a simple glycerol ether, when added to Jerne plates greatly reduced the number of hemolytic plaques. This effect appeared to be related to dose, and was clearly demonstrable with antibody-forming spleen cells from mice that had been immunized either with sheep red blood cells or with penicillin G conjugated with Keyhole limpet hemocyanin. Chlorphenesin did not affect the antigen, destroy complement, or interfere with the interaction of complement and the antigen-antibody complexes. Incubation of spleen cell suspensions with chlorphenesin prior to plating was more effective in reducing the number of plaques than was addition of the substance to the plates. It may act by reducing the ability of antibodies to react with antigens or by affecting the release of antibodies from the spleen cells.

An assessment of the 3D geometric surrogacy of shock timing diagnostic techniques for tuning experiments on the NIF

Science.gov (United States)

Robey, H. F.; Munro, D. H.; Spears, B. K.; Marinak, M. M.; Jones, O. S.; Patel, M. V.; Haan, S. W.; Salmonson, J. D.; Landen, O. L.; Boehly, T. R.; Nikroo, A.

2008-05-01

Ignition capsule implosions planned for the National Ignition Facility (NIF) require a pulse shape with a carefully designed series of four steps, which launch a corresponding series of shocks through the ablator and DT ice shell. The relative timing of these shocks is critical for maintaining the DT fuel on a low adiabat. The current NIF specification requires that the timing of all four shocks be tuned to an accuracy of surrogacy of this modified geometry, 3D simulations using HYDRA [1] have been performed. The results from simulations of a quarter of the target geometry are presented. Comparisons of the hohlraum drive conditions and the resulting effect on the shock timing in the keyhole hohlraum are compared with the corresponding results for the standard ignition hohlraum.

Influence of the crack propagation rate in the obtaining opening and closing stress intensity factor by finite element method

Directory of Open Access Journals (Sweden)

Luiz Carlos H. Ricardo

2016-03-01

Full Text Available Crack propagation simulation began with the development of the finite element method; the analyses were conducted to obtain a basic understanding of the crack growth. Today structural and materials engineers develop structures and materials properties using this technique as criterion design. The aim of this paper is to verify the effect of different crack propagation rates in determination of crack opening and closing stress of an ASTM specimen under a standard suspension spectrum loading from FD&E SAE Keyhole Specimen Test Load Histories by finite element analysis. The crack propagation simulation was based on release nodes at the minimum loads to minimize convergence problems. To understand the crack propagation processes under variable amplitude loading, retardation effects are discussed.

Approaches to teaching primary level mathematics

Directory of Open Access Journals (Sweden)

Caroline Long

2014-12-01

Full Text Available In this article we explore approaches to curriculum in the primary school in order to map and manage the omissions implicit in the current unfolding of the Curriculum and Assessment Policy Statement for mathematics. The focus of school-based research has been on curriculum coverage and cognitive depth. To address the challenges of teaching mathematics from the perspective of the learner, we ask whether the learners engage with the subject in such a way that they build foundations for more advanced mathematics. We firstly discuss three approaches that inform the teaching of mathematics in the primary school and which may be taken singly or in conjunction into organising the curriculum: the topics approach, the process approach, and the conceptual fields approach. Each of the approaches is described and evaluated by presenting both their advantages and disadvantages. We then expand on the conceptual fields approach by means of an illustrative example. The planning of an instructional design integrates both a topics and a process approach into a conceptual fields approach. To address conceptual depth within this approach, we draw on five dimensions required for understanding a mathematical concept. In conclusion, we reflect on an approach to curriculum development that draws on the integrated theory of conceptual fields to support teachers and learners in the quest for improved teaching and learning.

An Approach to Interface Synthesis

DEFF Research Database (Denmark)

Madsen, Jan; Hald, Bjarne

1995-01-01

Presents a novel interface synthesis approach based on a one-sided interface description. Whereas most other approaches consider interface synthesis as optimizing a channel to existing client/server modules, we consider the interface synthesis as part of the client/server module synthesis (which...... may contain the re-use of existing modules). The interface synthesis approach describes the basic transformations needed to transform the server interface description into an interface description on the client side of the communication medium. The synthesis approach is illustrated through a point...

[Alternative approaches in thyroid surgery].

Science.gov (United States)

Maurer, E; Wächter, S; Bartsch, D K

2017-08-01

In thyroid surgery multiple different cervical minimally invasive (partly endoscopically assisted) and extracervical endoscopic (partly robot-assisted) approaches have been developed in the last 20 years. The aim of all these alternative approaches to the thyroid gland is optimization of the cosmetic result. The indications for the use of alternative and conventional approaches are principally the same. Important requirements for the use of alternative methods are nevertheless a broad experience in conventional thyroid operations of the thyroid and adequate patient selection under consideration of the size of the thyroid and the underlying pathology. Contraindications for the use of alternative approaches are a large size of the thyroid gland including local symptoms, advanced carcinomas, reoperations and previous radiations of the anterior neck. The current article gives an overview of the clinically implemented alternative approaches for thyroid surgery. Of those the majority must still be considered as experimental. The alternative approaches to the thyroid gland can be divided in cervical minimally invasive, extracervical endosopic (robot-assisted) and transoral operations (natural orifice transluminal endoscopic surgery, NOTES). Since conventional thyroid operations are standardized procedures with low complication rates, alternative approaches to the thyroid gland are considered critically in Germany. The request for a perfect cosmetic result should not overweigh patients' safety. Only a few alternative approaches (e. g. MIVAT, RAT) can yet be considered as a safe addition in experienced hands in highly selected patients.

Life History Approach

DEFF Research Database (Denmark)

Olesen, Henning Salling

2015-01-01

as in everyday life. Life histories represent lived lives past, present and anticipated future. As such they are interpretations of individuals’ experiences of the way in which societal dynamics take place in the individual body and mind, either by the individual him/herself or by another biographer. The Life...... History approach was developing from interpreting autobiographical and later certain other forms of language interactive material as moments of life history, i.e. it is basically a hermeneutic approach. Talking about a psycho-societal approach indicates the ambition of attacking the dichotomy...... of the social and the psychic, both in the interpretation procedure and in some main theoretical understandings of language, body and mind. My article will present the reflections on the use of life history based methodology in learning and education research as a kind of learning story of research work....

Perception approaches and practices of local farming and development: an anthropological approach

International Nuclear Information System (INIS)

Hadi, S.A.; Chaudhry, A.G.

2015-01-01

The study focused on recognizing the local approaches of farming in designing and implementation of development projects. These approaches are representative of a particular ecological, social, economical, and political system, shaped by the constraints and opportunities associated to the area. Effective and successful development projects must include the local perceptions, their approaches and practices, as the locals are the ones most representative of their issues and have the most workable solution to them. The traditional agriculture has completely been clutched into the nexus of modern farming methods, due to which they are being abandoned by the farmers. Modern farming which is representative of development has increased the competition, transitioning, breaking the community into people experimenting on modern technology and those who are still finding means to adapt their traditional agriculture to the fast changing needs of the societies. The research was carried out in the villages of Ghora Gali and Aruka through qualitative and quantitative methods. Sustainable development in Pakistan thus needs to be reinvented in the local perspective considering approaches and practices and, eradicating the alien chains of development completely. (author)

Worse patient-reported outcome after lateral approach than after anterior and posterolateral approach in primary hip arthroplasty

Science.gov (United States)

Havelin, Leif I; Furnes, Ove; Baste, Valborg; Nordsletten, Lars; Hovik, Oystein; Dimmen, Sigbjorn

2014-01-01

Background The surgical approach in total hip arthroplasty (THA) is often based on surgeon preference and local traditions. The anterior muscle-sparing approach has recently gained popularity in Europe. We tested the hypothesis that patient satisfaction, pain, function, and health-related quality of life (HRQoL) after THA is not related to the surgical approach. Patients 1,476 patients identified through the Norwegian Arthroplasty Register were sent questionnaires 1–3 years after undergoing THA in the period from January 2008 to June 2010. Patient-reported outcome measures (PROMs) included the hip disability osteoarthritis outcome score (HOOS), the Western Ontario and McMaster Universities osteoarthritis index (WOMAC), health-related quality of life (EQ-5D-3L), visual analog scales (VAS) addressing pain and satisfaction, and questions about complications. 1,273 patients completed the questionnaires and were included in the analysis. Results Adjusted HOOS scores for pain, other symptoms, activities of daily living (ADL), sport/recreation, and quality of life were significantly worse (p < 0.001 to p = 0.03) for the lateral approach than for the anterior approach and the posterolateral approach (mean differences: 3.2–5.0). These results were related to more patient-reported limping with the lateral approach than with the anterior and posterolateral approaches (25% vs. 12% and 13%, respectively; p < 0.001). Interpretation Patients operated with the lateral approach reported worse outcomes 1–3 years after THA surgery. Self-reported limping occurred twice as often in patients who underwent THA with a lateral approach than in those who underwent THA with an anterior or posterolateral approach. There were no significant differences in patient-reported outcomes after THA between those who underwent THA with a posterolateral approach and those who underwent THA with an anterior approach. PMID:24954494

Flipped Classroom Approach

OpenAIRE

Fezile Ozdamli; Gulsum Asiksoy

2016-01-01

Flipped classroom is an active, student-centered approach that was formed to increase the quality of period within class. Generally this approach whose applications are done mostly in Physical Sciences, also attracts the attention of educators and researchers in different disciplines recently. Flipped classroom learning which wide-spreads rapidly in the world, is not well recognized in our country. That is why the aim of study is to attract attention to its potential in education field and pr...

Otoplasty: A graduated approach.

Science.gov (United States)

Foda, H M

1999-01-01

Numerous otoplastic techniques have been described for the correction of protruding ears. Technique selection in otoplasty should be done only after careful analysis of the abnormal anatomy responsible for the protruding ear deformity. A graduated surgical approach is presented which is designed to address all contributing factors to the presenting auricular deformity. The approach starts with the more conservative cartilage-sparing suturing techniques, then proceeds to incorporate other more aggressive cartilage weakening maneuvers. Applying this approach resulted in better long-term results with less postoperative lateralization than that encountered on using the cartilage-sparing techniques alone.

Congress of Neurological Surgeons Systematic Review and Evidence-Based Guidelines on Surgical Resection for the Treatment of Patients With Vestibular Schwannomas.

Science.gov (United States)

Hadjipanayis, Constantinos G; Carlson, Matthew L; Link, Michael J; Rayan, Tarek A; Parish, John; Atkins, Tyler; Asher, Anthony L; Dunn, Ian F; Corrales, C Eduardo; Van Gompel, Jamie J; Sughrue, Michael; Olson, Jeffrey J

2018-02-01

What surgical approaches for vestibular schwannomas (VS) are best for complete resection and facial nerve (FN) preservation when serviceable hearing is present? There is insufficient evidence to support the superiority of either the middle fossa (MF) or the retrosigmoid (RS) approach for complete VS resection and FN preservation when serviceable hearing is present. Which surgical approach (RS or translabyrinthine [TL]) for VS is best for complete resection and FN preservation when serviceable hearing is not present? There is insufficient evidence to support the superiority of either the RS or the TL approach for complete VS resection and FN preservation when serviceable hearing is not present. Does VS size matter for facial and vestibulocochlear nerve preservation with surgical resection? Level 3: Patients with larger VS tumor size should be counseled about the greater than average risk of loss of serviceable hearing. Should small intracanalicular tumors (<1.5 cm) be surgically resected? There are insufficient data to support a firm recommendation that surgery be the primary treatment for this subclass of VSs. Is hearing preservation routinely possible with VS surgical resection when serviceable hearing is present? Level 3: Hearing preservation surgery via the MF or the RS approach may be attempted in patients with small tumor size (<1.5 cm) and good preoperative hearing. When should surgical resection be the initial treatment in patients with neurofibromatosis type 2 (NF2)? There is insufficient evidence that surgical resection should be the initial treatment in patients with NF2. Does a multidisciplinary team, consisting of neurosurgery and neurotology, provides the best outcomes of complete resection and facial/vestibulocochlear nerve preservation for patients undergoing resection of VSs? There is insufficient evidence to support stating that a multidisciplinary team, usually consisting of a neurosurgeon and a neurotologist, provides superior outcomes compared

Belene nuclear power plant contracting approach

International Nuclear Information System (INIS)

Tankosic, D.; Mignone, O.

2004-01-01

Historically, three main types of project execution and contractual approaches have been applied to energy and industrial projects, including nuclear projects. These approaches are grouped into three broad categories: 1) Turnkey Approach; 2) Split Package (Island) Approach; and 3)Multiple Package Approach. Based on a preliminary screening done by an ongoing feasibility study work for NPP Belene (NEK contract to Parsons E and C), the recommended approach is going to follow that general trend i.e., with some variation between the Split Package and the Turnkey approach. Before deciding on an execution approach or at least before issuing bid specifications for the nuclear power plant, it is prudent, even for a country with existing nuclear power program (like Bulgaria), to re-check/verify capabilities of the interested bidders to handle contracts of this size and nature. During the last decades, nuclear energy went through a substantial restructuring and most of the capabilities (human and financial) that existed before are not any more available. This re-checking should mainly cover the experience of the bidders as regards the design, construction and operation of the stations where they were involved, but also include items such as local experience, capability to bring favorable financing, liability coverage, general background, potential and organizational structures. The advantages and disadvantages for the Owner of the three contracting approaches can be briefly summarized as follows: Turnkey Approach - main advantages: all responsibilities rest in a Contractor or Consortium. Main disadvantages - limited project control by Owner and restricted local participation. For Split Package Contract Approach main advantage are more favorable financing conditions and increased local participation. Main disadvantage is the increased interface problems. For Multiple package Contract Approach main advantages are the opportunity to tailor the plant and maximum increase of local

Revitalizing the setting approach

DEFF Research Database (Denmark)

Bloch, Paul; Toft, Ulla; Reinbach, Helene Christine

2014-01-01

BackgroundThe concept of health promotion rests on aspirations aiming at enabling people to increase control over and improve their health. Health promotion action is facilitated in settings such as schools, homes and work places. As a contribution to the promotion of healthy lifestyles, we have ...... approach is based on ecological and whole-systems thinking, and stipulates important principles and values of integration, participation, empowerment, context and knowledge-based development....... further developed the setting approach in an effort to harmonise it with contemporary realities (and complexities) of health promotion and public health action. The paper introduces a modified concept, the supersetting approach, which builds on the optimised use of diverse and valuable resources embedded...... in local community settings and on the strengths of social interaction and local ownership as drivers of change processes. Interventions based on a supersetting approach are first and foremost characterised by being integrated, but also participatory, empowering, context-sensitive and knowledge...

Approaches to understand culture

DEFF Research Database (Denmark)

Rasmussen, Lauge Baungaard; Rauner, Felix

1996-01-01

Different approaches to understand the concept ofculture are presented and evaluated. The author'sconcept of culture is defined. Different aspectsof the concept are discussed.......Different approaches to understand the concept ofculture are presented and evaluated. The author'sconcept of culture is defined. Different aspectsof the concept are discussed....

Approaches toward learning in physiotherapy

Directory of Open Access Journals (Sweden)

L. Keiller

2013-11-01

Full Text Available The aim of this study was to investigate the approaches toward learning of undergraduate Physiotherapy students in a PBl module to enhance facilitation of learning at the Stellenbosch University, Division of Physiotherapy in South Africa. This quantitative, descriptive study utilized the revised Two-factor Study Process Questionnaire (r-SPQ-2f to evaluate the study cohorts’ approaches toward learning in the module. results of the data instruments were analysed statistically and discussed in a descriptive manner. There were a statistically significant greater number of students who adopted a deep approach toward learning at the commencement of the academic year. Students showed a trend toward an increase in their intrinsic interest in the learning material as the module progressed. Students in the Applied Physiotherapy module (ATP started to shift their focus from a surface learning approach to a deep learning approach. further research is needed to determine the long-term changes in approach toward learning and the possible determinants of these changes. This can be done in conjunction with the implementation of quality assurance mechanisms for learning material and earlier preparation of students for the change in the learning environment.

Systems Biology-an interdisciplinary approach.

Science.gov (United States)

Friboulet, Alain; Thomas, Daniel

2005-06-15

System-level approaches in biology are not new but foundations of "Systems Biology" are achieved only now at the beginning of the 21st century [Kitano, H., 2001. Foundations of Systems Biology. MIT Press, Cambridge, MA]. The renewed interest for a system-level approach is linked to the progress in collecting experimental data and to the limits of the "reductionist" approach. System-level understanding of native biological and pathological systems is needed to provide potential therapeutic targets. Examples of interdisciplinary approach in Systems Biology are described in U.S., Japan and Europe. Robustness in biology, metabolic engineering and idiotypic networks are discussed in the framework of Systems Biology.

The paramedian supracerebellar infratentorial approach.

Science.gov (United States)

La Pira, Biagia; Sorenson, Thomas; Quillis-Quesada, Vicent; Lanzino, Giuseppe

2017-08-01

Lesions of the superior cerebellar surface, pineal region, lateral and dorsal midbrain and mesial temporal lobe are challenging to treat and often require neurosurgical intervention. The paramedian variation of the supracerebellar infratentorial approach utilizes the downward slope of the cerebellum to facilitate exposure and the lower density of cerebellar bridging veins away from the midline decreases the need to sacrifice larger venous channels. We also discuss our experiences with the approach, and some of the drawbacks and nuances that we have encountered as it has evolved over the years. This approach is versatile and effective and the authors' surgical approach of choice for resecting these challenging lesions.

Field theory approach to gravitation

International Nuclear Information System (INIS)

Yilmaz, H.

1978-01-01

A number of authors considered the possibility of formulating a field-theory approach to gravitation with the claim that such an approach would uniquely lead to Einstein's theory of general relativity. In this article it is shown that the field theory approach is more generally applicable and uniqueness cannot be claimed. Theoretical and experimental reasons are given showing that the Einsteinian limit appears to be unviable

A systems approach to obesity

Science.gov (United States)

Bartsch, Sarah M.; Mui, Yeeli; Haidari, Leila A.; Spiker, Marie L.; Gittelsohn, Joel

2017-01-01

Obesity has become a truly global epidemic, affecting all age groups, all populations, and countries of all income levels. To date, existing policies and interventions have not reversed these trends, suggesting that innovative approaches are needed to transform obesity prevention and control. There are a number of indications that the obesity epidemic is a systems problem, as opposed to a simple problem with a linear cause-and-effect relationship. What may be needed to successfully address obesity is an approach that considers the entire system when making any important decision, observation, or change. A systems approach to obesity prevention and control has many benefits, including the potential to further understand indirect effects or to test policies virtually before implementing them in the real world. Discussed here are 5 key efforts to implement a systems approach for obesity prevention: 1) utilize more global approaches; 2) bring new experts from disciplines that do not traditionally work with obesity to share experiences and ideas with obesity experts; 3) utilize systems methods, such as systems mapping and modeling; 4) modify and combine traditional approaches to achieve a stronger systems orientation; and 5) bridge existing gaps between research, education, policy, and action. This article also provides an example of how a systems approach has been used to convene a multidisciplinary team and conduct systems mapping and modeling as part of an obesity prevention program in Baltimore, Maryland. PMID:28049754

Posterior Approach to Kidney Dissection: An Old Surgical Approach for Integrated Medical Curricula

Science.gov (United States)

Daly, Frank J.; Bolender, David L.; Jain, Deepali; Uyeda, Sheryl; Hoagland, Todd M.

2015-01-01

Integrated medical curricular changes are altering the historical regional anatomy approach to abdominal dissection. The renal system is linked physiologically and biochemically to the cardiovascular and respiratory systems; yet, anatomists often approach the urinary system as part of the abdomen and pelvic regions. As part of an integrated…

Network Approach in Political Communication Studies

Directory of Open Access Journals (Sweden)

Нина Васильевна Опанасенко

2013-12-01

Full Text Available The article is devoted to issues of network approach application in political communication studies. The author considers communication in online and offline areas and gives the definition of rhizome, its characteristics, identifies links between rhizome and network approach. The author also analyses conditions and possibilities of the network approach in modern political communication. Both positive and negative features of the network approach are emphasized.

Thematic curriculum approach

Directory of Open Access Journals (Sweden)

Šefer Jasmina P.

2003-01-01

Full Text Available Thematic curriculum combines disciplines and media. The process is problem-oriented and the scenario most often follows the logic of exploring or storytelling. Those two approaches to teaching are appropriate because they fit into interdisciplinary and creative open-ended problem solving through play, as insisted upon by thematic curriculum. The matrix, where seven types of abilities intersect with five types of problems according to their degree of openness, defines well the outcomes of teaching. However, it did not prove to be suitable for planning the majority of activities in thematic curriculum, for it follows with difficulty the process of exploring or storytelling i.e. it disrupts the subject matter coherence of thematic curriculum. Therefore, it is suggested that matrix should be used for disciplinary curriculum planning but for that of thematic curriculum only in exclusive cases. The matrix should be used primarily as a framework for evaluating the distribution of various types of abilities and problem situations in teaching. The logic of diverse approaches to teaching reflects itself in the manner of planning and organizing the teaching process. Conceptual, visual-graphic, structural and other aids employed during educational process planning should suit the nature of the approach chosen. On the basis of qualitative investigations of educational process, in the present paper considerations are given to various approaches to teaching development of various drafts for the planning of teaching, and recognition of the logic of storytelling and exploring in thematic curriculum.

Anterior approach for knee arthrography

International Nuclear Information System (INIS)

Zurlo, J.V.; Towers, J.D.; Golla, S.

2001-01-01

Objective. To develop a new method of magnetic resonance arthrography (MRA) of the knee using an anterior approach analogous to the portals used for knee arthroscopy.Design. An anterior approach to the knee joint was devised mimicking anterior portals used for knee arthroscopy. Seven patients scheduled for routine knee MRA were placed in a decubitus position and under fluoroscopic guidance a needle was advanced from a position adjacent to the patellar tendon into the knee joint. After confirmation of the needle tip location, a dilute gadolinium solution was injected.Results and conclusion. All the arthrograms were technically successful. The anterior approach to knee MRA has greater technical ease than the traditional approach with little patient discomfort. (orig.)

Efficient approach for reliability-based optimization based on weighted importance sampling approach

International Nuclear Information System (INIS)

Yuan, Xiukai; Lu, Zhenzhou

2014-01-01

An efficient methodology is presented to perform the reliability-based optimization (RBO). It is based on an efficient weighted approach for constructing an approximation of the failure probability as an explicit function of the design variables which is referred to as the ‘failure probability function (FPF)’. It expresses the FPF as a weighted sum of sample values obtained in the simulation-based reliability analysis. The required computational effort for decoupling in each iteration is just single reliability analysis. After the approximation of the FPF is established, the target RBO problem can be decoupled into a deterministic one. Meanwhile, the proposed weighted approach is combined with a decoupling approach and a sequential approximate optimization framework. Engineering examples are given to demonstrate the efficiency and accuracy of the presented methodology

Alternative approaches to risk-based technical specifications

International Nuclear Information System (INIS)

Atefi, B.; Gallagher, D.W.; Liner, R.T.; Lofgren, E.V.

1987-01-01

Four alternative risk-based approaches to Technical Specifications are identified. These are: a Probabilistic Risk Assessment (PRA) oriented approach; a reliability goal-oriented approach; an approach based on configuration control; a data-oriented approach. Based on preliminary results, the PRA-oriented approach, which has been developed further than the other approaches, seems to offer a logical, quantitative basis for setting Allowed Outage Times (AOTs) and Surveillance Test Intervals (STIs) for some plant components and systems. The most attractive feature of this approach is that it directly links the AOTs and STIs with the risk associated with the operation of the plant. This would focus the plant operator's and the regulatory agency's attention on the most risk-significant components of the plant. A series of practical issues related to the level of detail and content of the plant PRAs, requirements for the review of these PRAs, and monitoring cf the plant's performance by the regulatory agency must be resolved before the approach could be implemented. Future efforts will examine the other three approaches and their practicality before firm conclusions are drawn regarding the viability of any of these approaches

Approaches to acceptable risk

International Nuclear Information System (INIS)

Whipple, C.

1997-01-01

Several alternative approaches to address the question open-quotes How safe is safe enough?close quotes are reviewed and an attempt is made to apply the reasoning behind these approaches to the issue of acceptability of radiation exposures received in space. The approaches to the issue of the acceptability of technological risk described here are primarily analytical, and are drawn from examples in the management of environmental health risks. These include risk-based approaches, in which specific quantitative risk targets determine the acceptability of an activity, and cost-benefit and decision analysis, which generally focus on the estimation and evaluation of risks, benefits and costs, in a framework that balances these factors against each other. These analytical methods tend by their quantitative nature to emphasize the magnitude of risks, costs and alternatives, and to downplay other factors, especially those that are not easily expressed in quantitative terms, that affect acceptance or rejection of risk. Such other factors include the issues of risk perceptions and how and by whom risk decisions are made

Fuel cycle oriented approach

International Nuclear Information System (INIS)

Petit, A.

1987-01-01

The term fuel cycle oriented approach is currently used to designate two quite different things: the attempt to consider all or part of a national fuel cycle as one material balance area (MBA) or to consider individual MBAs existing in a state while designing a unique safeguards approach for each and applying the principle of nondiscrimination to fuel cycles as a whole, rather than to individual facilities. The merits of such an approach are acceptability by the industry and comparison with the contemplated establishment of long-term criteria. The following points concern the acceptability by the industry: (1) The main interest of the industry is to keep an open international market and therefore, to have effective and efficient safeguards. (2) The main concerns of the industry regarding international safeguards are economic burden, intrusiveness, and discrimination. Answers to these legitimate concerns, which retain the benefits of a fuel cycle oriented approach, are needed. More specifically, the problem of reimbursing the operator the costs that he has incurred for the safeguards must be considered

Transbasal versus endoscopic endonasal versus combined approaches for olfactory groove meningiomas: importance of approach selection.

Science.gov (United States)

Liu, James K; Silva, Nicole A; Sevak, Ilesha A; Eloy, Jean Anderson

2018-04-01

OBJECTIVE There has been much debate regarding the optimal surgical approach for resecting olfactory groove meningiomas (OGMs). In this paper, the authors analyzed the factors involved in approach selection and reviewed the surgical outcomes in a series of OGMs. METHODS A retrospective review of 28 consecutive OGMs from a prospective database was conducted. Each tumor was treated via one of 3 approaches: transbasal approach (n = 15), pure endoscopic endonasal approach (EEA; n = 5), and combined (endoscope-assisted) transbasal-EEA (n = 8). RESULTS The mean tumor volume was greatest in the transbasal (92.02 cm 3 ) and combined (101.15 cm 3 ) groups. Both groups had significant lateral dural extension over the orbits (transbasal 73.3%, p 95%) was achieved in 20% of transbasal and 37.5% of combined cases, all due to tumor adherence to the critical neurovascular structures. The rate of CSF leakage was 0% in the transbasal and combined groups, and there was 1 leak in the EEA group (20%), resulting in an overall CSF leakage rate of 3.6%. Olfaction was preserved in 66.7% in the transbasal group. There was no significant difference in length of stay or 30-day readmission rate between the 3 groups. The mean modified Rankin Scale score was 0.79 after the transbasal approach, 2.0 after EEA, and 2.4 after the combined approach (p = 0.0604). The mean follow-up was 14.5 months (range 1-76 months). CONCLUSIONS The transbasal approach provided the best clinical outcomes with the lowest rate of complications for large tumors (> 40 mm) and for smaller tumors (OGMs invading the sinonasal cavity. Careful patient selection using an individualized, tailored strategy is important to optimize surgical outcomes.

The clinical utility of a adding lateral approach to conventional vertical approach for prone stereotactic vacuum-assisted breast biopsy

International Nuclear Information System (INIS)

Myong, Joo Hwa; Kang, Bong Joo; Yoon, Soo Kyung; Kim, Sung Hun; An, Yeong Yi

2013-01-01

The purpose of this study is to evaluate the clinical utility of adding lateral approach to conventional vertical approach for prone stereotactic vacuum-assisted breast biopsies. From April 2010 to May 2012, 130 vacuum-assisted stereotactic biopsies were attempted in 127 patients. While a vertical approach was preferred, a lateral approach was used if the vertical approach failed. The success rate of biopsies utilizing only a vertical approach was compared with that using both vertical and lateral approaches and the breast thickness for both procedures was measured and compared with that for vertical approach. In addition, pathology results were evaluated and the causes of the failed biopsies were analyzed. Of the 130 cases, 127 biopsies were performed and 3 biopsies failed. The success rate of the vertical approach was 83.8% (109/130); however, when the lateral approach was also used, the success rate increased to 97.7% (127/130) (p = 0.0004). The mean breast thickness was 2.7 ± 1 cm for the lateral approach and 4 ± 1.2 cm for the vertical approach (p < 0.0001). The histopathologic results in 76 (59.8%) of the biopsies were benign, 23 (18.1%) were high-risk lesions, and 28 (22.0%) were malignant. The causes of biopsy failure were thin breasts (n = 2) and undetected difficult lesion location (n = 1). The addition of lateral approach to conventional vertical approach in prone stereotactic vacuum-assisted breast biopsy improved the success rate of stereotactic biopsy, especially in patients with thin breasts.

Correlation between diagnostic capability of MR-mammography and histology of tissue adjacent to tumor

Energy Technology Data Exchange (ETDEWEB)

Takahara, Taro [St. Marianna Univ., Kawasaki, Kanagawa (Japan)

1996-12-01

The purpose of this paper is to evaluate correlation between the capability in the diagnosis of tumor extent and histology of adjacent tissue. MR-mammography (MRM) was obtained in twenty-one patients with surgically resected breast cancer by 0.5 T superconducting magnet (PHILIPS GY-ROSCAN T5-II, release 3.1). Pre and postcontrast 3D-spoiled gradient echo sequence were employed for MRM with spectral presaturation with inversion recovery (SPIR) and on-resonance MTC. The contrast determination time, the passing time of the center of k-space, was 1 min 50 s in 14 cases with key-hole imaging, and 2 min 46 s in 7 cases without key-hole imaging. Early enhancing area was considered as a tumor and an accuracy of tumor extent was evaluated by two radiologists. Accurate interpretation was obtained in 9 of 9 cases with atrophic mammary gland with fatty replacement and 3 of 3 cases with severe fibrosis in mammary gland. Seven cases were unclear in tumor margin due to intense enhancement of the adjacent tissue. One of 3 cases with normal mammary gland showed unclear margin of the tumor, which corresponded to the area of rich population of lobules in a young patient. Two of 2 cases of fibrocystic change with nonproliferative lesions in one case and proliferative lesions without atypia in another, showed unclear margin of tumor. Two cases of 2 intraductal spreading and 2 of 2 cases of massive interstitial invasion also showed unclear margin. The accuracy of tumor extent was found to have no correlation with either histology or enhancing ratio of the tumor. In conclusion, it is warranted to say that histology of adjacent tissue is an important factor to determine diagnostic capability of tumor extent by MRM. Fat replacement and fibrosis of the surrounding tissue are main causes of clear visualization of tumor, while normal mammary gland in young patients, fibrocystic change, intraductal spreading and invasion lead to the unclearness of tumor margin. (author)

Correlation between diagnostic capability of MR-mammography and histology of tissue adjacent to tumor

International Nuclear Information System (INIS)

Takahara, Taro

1996-01-01

The purpose of this paper is to evaluate correlation between the capability in the diagnosis of tumor extent and histology of adjacent tissue. MR-mammography (MRM) was obtained in twenty-one patients with surgically resected breast cancer by 0.5 T superconducting magnet (PHILIPS GY-ROSCAN T5-II, release 3.1). Pre and postcontrast 3D-spoiled gradient echo sequence were employed for MRM with spectral presaturation with inversion recovery (SPIR) and on-resonance MTC. The contrast determination time, the passing time of the center of k-space, was 1 min 50 s in 14 cases with key-hole imaging, and 2 min 46 s in 7 cases without key-hole imaging. Early enhancing area was considered as a tumor and an accuracy of tumor extent was evaluated by two radiologists. Accurate interpretation was obtained in 9 of 9 cases with atrophic mammary gland with fatty replacement and 3 of 3 cases with severe fibrosis in mammary gland. Seven cases were unclear in tumor margin due to intense enhancement of the adjacent tissue. One of 3 cases with normal mammary gland showed unclear margin of the tumor, which corresponded to the area of rich population of lobules in a young patient. Two of 2 cases of fibrocystic change with nonproliferative lesions in one case and proliferative lesions without atypia in another, showed unclear margin of tumor. Two cases of 2 intraductal spreading and 2 of 2 cases of massive interstitial invasion also showed unclear margin. The accuracy of tumor extent was found to have no correlation with either histology or enhancing ratio of the tumor. In conclusion, it is warranted to say that histology of adjacent tissue is an important factor to determine diagnostic capability of tumor extent by MRM. Fat replacement and fibrosis of the surrounding tissue are main causes of clear visualization of tumor, while normal mammary gland in young patients, fibrocystic change, intraductal spreading and invasion lead to the unclearness of tumor margin. (author)

Cell approach to glass transition

International Nuclear Information System (INIS)

Aste, Tomaso; Coniglio, Antonio

2003-01-01

We present a novel theoretical approach to understanding the complex dynamics of glass-forming liquids, granular packings and amorphous solids. This theory, which is an elaboration of the free volume and inherent structure approaches, allows one to retrieve the thermodynamical properties of these systems from studies of geometrical and topological properties of local, static configurations alone. When applied to hard-sphere systems, the present theory reproduces with a good quantitative agreement the equation of state for the crystalline and the disordered glassy phases. Moreover, we find that, as the density approaches a critical value close to the random close-packing density, the configurational entropy approaches zero and the large relaxation time diverges according to the Vogel-Fulcher behaviour, following also the Adam-Gibbs relation

Approaches for assessing sustainable remediation

DEFF Research Database (Denmark)

Søndergaard, Gitte Lemming; Binning, Philip John; Bjerg, Poul Løgstrup

Sustainable remediation seeks to reduce direct contaminant point source impacts on the environment, while minimizing the indirect cost of remediation to the environment, society and economy. This paper presents an overview of available approaches for assessing the sustainability of alternative...... remediation strategies for a contaminated site. Most approaches use multi-criteria assessment methods (MCA) to structure a decision support process. Different combinations of environmental, social and economic criteria are employed, and are assessed either in qualitative or quantitative forms with various...... tools such as life cycle assessment and cost benefit analysis. Stakeholder involvement, which is a key component of sustainable remediation, is conducted in various ways. Some approaches involve stakeholders directly in the evaluation or weighting of criteria, whereas other approaches only indirectly...

Study strategies and approaches to learning

DEFF Research Database (Denmark)

Christensen, Hans Peter

Process Questionnaire to identify their approach to learning. It was hypothesised that the students’ learning approach would depend more on the quality of the study work than on the quantity; that an active and reflective study strategy was required to obtain deep conceptual understanding. The result...... showed a weak correlation between the student’s main learning approach as defined by the ratio of the deep approach score to the surface approach score and the student’s study intensity as identified by the ratio of non-scheduled independent activities to scheduled teacher-controlled activities....... There was however a much stronger linear correlation (significant at the 0.01 level) between the deep-surface ratio and the total study load. The same result was observed when measuring other students’ study strategy and learning approach for a single course. The empirical basis is still too limited to draw...

High-Fidelity Aerothermal Engineering Analysis for Planetary Probes Using DOTNET Framework and OLAP Cubes Database

Directory of Open Access Journals (Sweden)

Prabhakar Subrahmanyam

2009-01-01

Full Text Available This publication presents the architecture integration and implementation of various modules in Sparta framework. Sparta is a trajectory engine that is hooked to an Online Analytical Processing (OLAP database for Multi-dimensional analysis capability. OLAP is an Online Analytical Processing database that has a comprehensive list of atmospheric entry probes and their vehicle dimensions, trajectory data, aero-thermal data and material properties like Carbon, Silicon and Carbon-Phenolic based Ablators. An approach is presented for dynamic TPS design. OLAP has the capability to run in one simulation several different trajectory conditions and the output is stored back into the database and can be queried for appropriate trajectory type. An OLAP simulation can be setup by spawning individual threads to run for three types of trajectory: Nominal, Undershoot and Overshoot trajectory. Sparta graphical user interface provides capabilities to choose from a list of flight vehicles or enter trajectory and geometry information of a vehicle in design. DOTNET framework acts as a middleware layer between the trajectory engine and the user interface and also between the web user interface and the OLAP database. Trajectory output can be obtained in TecPlot format, Excel output or in a KML (Keyhole Markup Language format. Framework employs an API (application programming interface to convert trajectory data into a formatted KML file that is used by Google Earth for simulating Earth-entry fly-by visualizations.

Poverty reduction Approaches in Kenya: Assessing the Usefulness of the Right Based Approach in Kenya

Directory of Open Access Journals (Sweden)

Wambua Leonard Munyao, Ph.D

2013-06-01

Full Text Available While billions of dollars have been spent in development projects in least developed countries, poverty continues to increase. This study proposes human-rights based approach to poverty eradication. To this end, the study seeks to assess the key determinants of use of rights- based approaches to poverty reduction and it’s usefulness in Kenya with special reference to NGOs in Kibera. The study further high lights some of the basic skills of implementing the rights based approach to poverty reduction. The attempts to establish the proportion of NGOs applying rights based approach to poverty reduction in Kibera Division as well. The review of relevant literature has been undertaken and a field study done. The study is informed by a qualitative human rights framework.

Opposite effects of total lymphoid irradiation on T cell-dependent and T cell-independent antibody responses

Energy Technology Data Exchange (ETDEWEB)

Tanay, A.; Strober, S.

1984-02-01

The effect of total lymphoid irradiation (TLI) on the primary antibody response to the dinitrophenylated heterologous protein, keyhole limpet hemocyanin (DNP-KLH), in complete Freund's adjuvant (CFA), and to the trinitrophenylated polysaccharide antigen, Brucella abortus (TNP-BA), was studied in BALB/c mice. The antibody response to both antigens was diminished in comparison with nonirradiated mice when antigens were injected within 3 days after TLI. When the mice were immunized 30 days after completion of TLI the antibody response to DNP-KLH in CFA was still diminished, but the antibody response to TNP-BA was enhanced 5- to 10-fold as compared with that of control animals. The opposite effect of TLI on the two antibody responses was also observed in a syngeneic primary adoptive transfer system.

The effect of plasma arc process parameters on the properties of dissimilar AISI 1040/AISI 304 steel plate welds

Energy Technology Data Exchange (ETDEWEB)

Kilic, Musa; Kirik, Ihsan; Orhan, Nuri [Firat Univ., Elazig (Turkey); Celik, Ferkan [Science Industry and Technology Ministry of Turkey (Turkey)

2012-11-01

In this study, 10 mm thick AISI 1040 and AISI 304 steel plates were welded in the butt position without pretreatment by plasma transferred arc (PTA) welding technique. Therefore, mechanical behaviour, microstructure, penetration depth and length were investigated. After welding, microstructural changes in the interface regions of the welded specimens were examined by scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). Micro-hardness as well as V-notch Charpy tests were performed to determine the mechanical properties of the welds. The influence of the welding parameters on the dimension and shape of the joints has been found out. From the results, it was derived that with the parameters used, a partly keyhole weld bead formed with a penetration depth of 10 mm and a width of 11 mm in butt position. (orig.)

Pre-Industry-Optimisation of the Laser Welding Process

DEFF Research Database (Denmark)

Gong, Hui

This dissertation documents the investigations into on-line monitoring the CO2 laser welding process and optimising the process parameters for achieving high quality welds. The requirements for realisation of an on-line control system are, first of all, a clear understanding of the dynamic...... phenomena of the laser welding process including the behaviour of the keyhole and plume, and the correlation between the adjustable process parameters: laser power, welding speed, focal point position, gas parameters etc. and the characteristics describing the quality of the weld: seam depth and width......, porosity etc. Secondly, a reliable monitoring system for sensing the laser-induced plasma and plume emission and detecting weld defects and process parameter deviations from the optimum conditions. Finally, an efficient control system with a fast signal processor and a precise feed-back controller...

Fully mechanized welding of pipelines in the chemical industry and reactor construction

International Nuclear Information System (INIS)

Born, K.

1984-01-01

Pipes are increasingly being used as a construction element involving a growing demand for modern welding technology. The pulsed-arc welding procedures occupy an important position in mechanized pipe welding especially where flanged joints are to be made on turning pipes with a burner fixed in place. When the construction prohibits the turning of pipes, the orbital welding technique may be used. The paper discusses the question how the economic efficiency of TIG in inert-gas welding, which is the commonly used welding technique, could be enhanced and in how far other pulsed-arc welding methods, e.g. plasma keyhole or MIG/MAG pulsed-arc could be used in future. This could be done using the new possibilities offered by modern power sources and process technology. (orig.) [de

Visions of our Planet's Atmosphere, Land and Oceans: Spectacular Visualizations of our Blue Marble

Science.gov (United States)

Hasler, A. F.; Starr, David (Technical Monitor)

2002-01-01

The NASA/NOAA Electronic Theater presents Earth science observations and visualizations in a historical perspective. Fly in from outer space to South Africa, Cape Town and Johannesburg using NASA Terra/MODIS data, Landsat data and 1 m IKONOS 'Spy Satellite' data. Zoom in to any place South Africa using Earth Viewer 3D from Keyhole Inc. and Landsat data at 30 m resolution. Go back to the early weather satellite images from the 1960s and see them contrasted with the latest US and international global satellite weather movies including hurricanes and 'tornadoes'. See the latest visualizations of spectacular images from NASA/NOAA remote sensing missions like Terra, GOES, TRMM, SeaWiFS, Landsat 7 including 1 - min GOES rapid scan image sequences of Nov 9th 2001 Midwest tornadic thunderstorms and have them explained.

Laser welding of thin polymer films to container substrates for aseptic packaging

Science.gov (United States)

Brown, N.; Kerr, D.; Jackson, M. R.; Parkin, R. M.

2000-03-01

Keyhole laser welding of polymers is a subject well covered and researched, but relatively little information exists regarding the welding of thin polymer films, particularly to a heavier substrate. This paper presents the design of a suitable test apparatus for laser welding thin film to a heavier substrate, and shows the results of an investigation into the feasibility of laser welding multi-layer polymer film lids to tubs for the manufacture of aseptic food containers. A consistent weld, free from defects, is the key to process success. Typical welding defects have been synthesised in order to investigate, and consequently remove, their cause. The result is a reliable welding method based on even film clamping. With careful attention to machine design, a seal of high mechanical strength and chemical integrity is possible.

Analysis and validation of laser spot weld-induced distortion

Energy Technology Data Exchange (ETDEWEB)

Knorovsky, G.A.; Kanouff, M.P.; Maccallum, D.O.; Fuerschbach, P.W.

1999-12-09

Laser spot welding is an ideal process for joining small parts with tight tolerances on weld size, location, and distortion, particularly those with near-by heat sensitive features. It is also key to understanding the overlapping laser spot seam welding process. Rather than attempting to simulate the laser beam-to-part coupling (particularly if a keyhole occurs), it was measured by calorimetry. This data was then used to calculate the thermal and structural response of a laser spot welded SS304 disk using the finite element method. Five combinations of process parameter values were studied. Calculations were compared to experimental data for temperature and distortion profiles measured by thermocouples and surface profiling. Results are discussed in terms of experimental and modeling factors. The authors then suggest appropriate parameters for laser spot welding.

The variable polarity plasma arc welding process: Characteristics and performance

Science.gov (United States)

Hung, R. J.; Zhu, G. J.

1991-01-01

Significant advantages of the Variable Polarity Plasma Arc (VPPA) Welding Process include faster welding, fewer repairs, less joint preparation, reduced weldment distortion, and absence of porosity. The power distribution was analyzed for an argon plasma gas flow constituting the fluid in the VPPA Welding Process. The major heat loss at the torch nozzle is convective heat transfer; in the space between the outlet of the nozzle and the workpiece; radiative heat transfer; and in the keyhole in the workpiece, convective heat transfer. The power absorbed at the workpiece produces the molten puddle that solidifies into the weld bead. Crown and root widths, and crown and root heights of the weld bead are predicted. The basis is provided for an algorithm for automatic control of VPPA welding machine parameters to obtain desired weld bead dimensions.

Looking through the Keyhole: Exploring Realities and Possibilities for School Breakfast Programs in Rural Western Australia

Directory of Open Access Journals (Sweden)

Simon O. Ichumar

2018-03-01

Full Text Available Objective: To assess the school breakfast program (SBP in two schools with high Aboriginal student populations in rural Western Australia, their contribution to holistic support, nutritional health education and possibilities for improvement. Methods: The operations and functioning of one regional and one remote SBP were assessed by stakeholder inquiry related to process and challenges, observations and documentary review. An intervention to increase health education, social interaction and learning about nutrition and food origins implemented in one school was assessed. Results: Strengths, system and structural factors that impeded realisation of optimal outcomes of the SBPs were identified. The SBPs focussed on serving food rather than building nutritional understanding or on social interactions and support. Systems for delivery and management of the programs largely relied on staff with limited time. When offered a more interactive and social environment, children enjoyed learning about food. Conclusions: Opportunities for SBPs to offer holistic support and educational enhancement for disadvantaged children are limited by the realities of pressures on staff to support them and a view constraining their primary role as food delivery. The lack of volunteer support in disadvantaged schools limits the potential benefits of SBPs in providing psychosocial support. Health education resources which exist for use in SBPs are not necessarily used.

Looking through the Keyhole: Exploring Realities and Possibilities for School Breakfast Programs in Rural Western Australia.

Science.gov (United States)

Ichumar, Simon O; Dahlberg, Emma E; Paynter, Ellen B; Lucey, Fiona M C; Chester, Miranda R; Papertalk, Lennelle; Thompson, Sandra C

2018-03-17

To assess the school breakfast program (SBP) in two schools with high Aboriginal student populations in rural Western Australia, their contribution to holistic support, nutritional health education and possibilities for improvement. The operations and functioning of one regional and one remote SBP were assessed by stakeholder inquiry related to process and challenges, observations and documentary review. An intervention to increase health education, social interaction and learning about nutrition and food origins implemented in one school was assessed. Strengths, system and structural factors that impeded realisation of optimal outcomes of the SBPs were identified. The SBPs focussed on serving food rather than building nutritional understanding or on social interactions and support. Systems for delivery and management of the programs largely relied on staff with limited time. When offered a more interactive and social environment, children enjoyed learning about food. Opportunities for SBPs to offer holistic support and educational enhancement for disadvantaged children are limited by the realities of pressures on staff to support them and a view constraining their primary role as food delivery. The lack of volunteer support in disadvantaged schools limits the potential benefits of SBPs in providing psychosocial support. Health education resources which exist for use in SBPs are not necessarily used.

Orion Emergency Mask Approach

Science.gov (United States)

Tuan, George C.; Graf, John C.

2009-01-01

Emergency mask approach on Orion poses a challenge to the traditional Shuttle or Station approaches. Currently, in the case of a fire or toxic spill event, the crew utilizes open loop oxygen masks that provide the crew with oxygen to breath, but also dumps the exhaled oxygen into the cabin. For Orion, with a small cabin volume, the extra oxygen will exceed the flammability limit within a short period of time, unless a nitrogen purge is also provided. Another approach to a fire or toxic spill event is the use of a filtering emergency masks. These masks utilize some form of chemical beds to scrub the air clean of toxic providing the crew safe breathing air for a period without elevating the oxygen level in the cabin. Using the masks and a form of smoke-eater filter, it may be possible to clean the cabin completely or to a level for safe transition to a space suit to perform a cabin purge. Issues with filters in the past have been the reaction time, breakthroughs, and high breathing resistance. Development in a new form of chemical filters has shown promise to make the filtering approach feasible.

The slice balance approach (SBA): a characteristic-based, multiple balance SN approach on unstructured polyhedral meshes

International Nuclear Information System (INIS)

Grove, R.E.

2005-01-01

The Slice Balance Approach (SBA) is an approach for solving geometrically-complex, neutral-particle transport problems within a multi-group discrete ordinates (S N ) framework. The salient feature is an angle-dependent spatial decomposition. We approximate general surfaces with arbitrary polygonal faces and mesh the geometry with arbitrarily-shaped polyhedral cells. A cell-local spatial decomposition divides cells into angle-dependent slices for each S N direction. This subdivision follows from a characteristic-based view of the transport problem. Most balance-based characteristic methods use it implicitly; we use it explicitly and exploit its properties. Our mathematical approach is a multiple balance approach using exact spatial moments balance equations on cells and slices along with auxiliary relations on slices. We call this the slice balance approach; it is a characteristic-based multiple balance approach. The SBA is intentionally general and can extend differencing schemes to arbitrary 2-D and 3-D meshes. This work contributes to development of general-geometry deterministic transport capability to complement Monte Carlo capability for large, geometrically-complex transport problems. The purpose of this paper is to describe the SBA. We describe the spatial decomposition and mathematical framework and highlight a few interesting properties. We sketch the derivation of two solution schemes, a step characteristic scheme and a diamond-difference-like scheme, to illustrate the approach and we present interesting results for a 2-D problem. (author)

The Rule-Assessment Approach and Education.

Science.gov (United States)

Siegler, Robert S.

1982-01-01

This paper describes the rule-assessment approach to cognitive development. The basic question that motivated the rule-assessment approach is how people's existing knowledge influences their ability to learn. Research using the rule-assessment approach is summarized in terms of eight conclusions, each illustrated with empirical examples.…

Statistical sampling approaches for soil monitoring

NARCIS (Netherlands)

Brus, D.J.

2014-01-01

This paper describes three statistical sampling approaches for regional soil monitoring, a design-based, a model-based and a hybrid approach. In the model-based approach a space-time model is exploited to predict global statistical parameters of interest such as the space-time mean. In the hybrid

Non-precision approach in manual mode

Directory of Open Access Journals (Sweden)

М. В. Коршунов

2013-07-01

Full Text Available Considered is the method of non-precision approach of an aircraft in the manual mode with a constant angle of path. Advantage of this method consists in the fact that the construction of approach with a constant angle of path provides the stable path of flight. It is also considered a detailed analysis of the possibility of the approach by the above-mentioned method. Conclusions contain recommendations regarding the use of the described method of non-precision approach during training flights.

Integrative medicine approach to chronic pain.

Science.gov (United States)

Teets, Raymond Y; Dahmer, Stephen; Scott, Emilie

2010-06-01

Chronic pain can be a frustrating condition for patient and clinician. The integrative medicine approach to pain can offer hope, adding safe complementary and alternative medical (CAM) therapies to mitigate pain and suffering. Such CAM therapies include nutrition, supplements and herbs, manual medicine, acupuncture, yoga, and mind-body approaches. The evidence is heterogeneous regarding these approaches, but some evidence suggests efficacy and confirms safety. The integrative medicine approach can be beneficial in a patient with chronic pain. Copyright 2010 Elsevier Inc. All rights reserved.

Energy management - The delayed flap approach

Science.gov (United States)

Bull, J. S.

1976-01-01

Flight test evaluation of a Delayed Flap approach procedure intended to provide reductions in noise and fuel consumption is underway using the NASA CV-990 test aircraft. Approach is initiated at a high airspeed (240 kt) and in a drag configuration that allows for low thrust. The aircraft is flown along the conventional ILS glide slope. A Fast/Slow message display signals the pilot when to extend approach flaps, landing gear, and land flaps. Implementation of the procedure in commercial service may require the addition of a DME navigation aid co-located with the ILS glide slope transmitter. The Delayed Flap approach saves 250 lb of fuel over the Reduced Flap approach, with a 95 EPNdB noise contour only 43% as large.

Effect of Bluetooth headset and mobile phone electromagnetic fields on the human auditory nerve.

Science.gov (United States)

Mandalà, Marco; Colletti, Vittorio; Sacchetto, Luca; Manganotti, Paolo; Ramat, Stefano; Marcocci, Alessandro; Colletti, Liliana

2014-01-01

The possibility that long-term mobile phone use increases the incidence of astrocytoma, glioma and acoustic neuroma has been investigated in several studies. Recently, our group showed that direct exposure (in a surgical setting) to cell phone electromagnetic fields (EMFs) induces deterioration of auditory evoked cochlear nerve compound action potential (CNAP) in humans. To verify whether the use of Bluetooth devices reduces these effects, we conducted the present study with the same experimental protocol. Randomized trial. Twelve patients underwent retrosigmoid vestibular neurectomy to treat definite unilateral Ménière's disease while being monitored with acoustically evoked CNAPs to assess direct mobile phone exposure or alternatively the EMF effects of Bluetooth headsets. We found no short-term effects of Bluetooth EMFs on the auditory nervous structures, whereas direct mobile phone EMF exposure confirmed a significant decrease in CNAPs amplitude and an increase in latency in all subjects. The outcomes of the present study show that, contrary to the finding that the latency and amplitude of CNAPs are very sensitive to EMFs produced by the tested mobile phone, the EMFs produced by a common Bluetooth device do not induce any significant change in cochlear nerve activity. The conditions of exposure, therefore, differ from those of everyday life, in which various biological tissues may reduce the EMF affecting the cochlear nerve. Nevertheless, these novel findings may have important safety implications. © 2013 The American Laryngological, Rhinological and Otological Society, Inc.

[Threefold intraoperative electrophysiological monitoring of vestibular neurectomy].

Science.gov (United States)

Hausler, R; Kasper, A

1991-01-01

A threefold intraoperative monitoring of facial nerve, auditory nerve and vestibular nerve function was performed in 14 cases of retrosigmoidal neurectomy. The facial nerve was monitoring with a pressure transducer placed against the cheek (Opalarm system). The auditory nerve was monitored with acoustically (click) evoked early potentials and the vestibular nerve was monitored with electrically evoked vestibular potentials obtained by direct stimulation (biphasic current pulses of 0.75-mA p-p, 100 us, 20/s) of the exposed vestibular nerve in the cerebellopontine angle before, during and after neurectomy. A characteristic vertex negative peak having a latency of approximately 2 ms and approximately 0.5 uV amplitude was obtained between a forehead and an ipsilateral ear lobe electrode (2 x 1,000 averaged responses over 10 ms) before the neurectomy. This response disappeared after selective vestibular nerve section proximal to the stimulation site. A diminished response amplitude was measured after incomplete nerve section. Simultaneous acoustic masking had no influence on the vestibular potential. The 14 operated patients became all free of vertiginous spells and drop-attacks except one patient who developed a contralateral Menière's. Facial nerve function remained normal in all. Hearing preservation was obtained in 12 patients (86%). The threefold intraoperative monitoring has turned out to be an additional safety factor for facial and auditory nerve preservation and, thanks to the recording of vestibular potentials, it increased the efficiency of vestibular neurectomy.

Ecosystem approach in education

Science.gov (United States)

Nabiullin, Iskander

2017-04-01

Environmental education is a base for sustainable development. Therefore, in our school we pay great attention to environmental education. Environmental education in our school is based on ecosystem approach. What is an ecosystem approach? Ecosystem is a fundamental concept of ecology. Living organisms and their non-living environments interact with each other as a system, and the biosphere planet functions as a global ecosystem. Therefore, it is necessary for children to understand relationships in ecosystems, and we have to develop systems thinking in our students. Ecosystem approach and systems thinking should help us to solve global environmental problems. How do we implement the ecosystem approach? Students must understand that our biosphere functions as a single ecosystem and even small changes can lead to environmental disasters. Even the disappearance of one plant or animal species can lead to irreversible consequences. So in the classroom we learn the importance of each living organism for the nature. We pay special attention to endangered species, which are listed in the Red Data List. Kids are doing projects about these organisms, make videos, print brochures and newspapers. Fieldwork also plays an important role for ecosystem approach. Every summer, we go out for expeditions to study species of plants and animals listed in the Red Data List of Tatarstan. In class, students often write essays on behalf of any endangered species of plants or animals, this also helps them to understand the importance of each living organism in nature. Each spring we organise a festival of environmental projects among students. Groups of 4-5 students work on a solution of environmental problems, such as water, air or soil pollution, waste recycling, the loss of biodiversity, etc. Participants shoot a clip about their project, print brochures. Furthermore, some of the students participate in national and international scientific Olympiads with their projects. In addition to

Fuzzy multiple linear regression: A computational approach

Science.gov (United States)

Juang, C. H.; Huang, X. H.; Fleming, J. W.

1992-01-01

This paper presents a new computational approach for performing fuzzy regression. In contrast to Bardossy's approach, the new approach, while dealing with fuzzy variables, closely follows the conventional regression technique. In this approach, treatment of fuzzy input is more 'computational' than 'symbolic.' The following sections first outline the formulation of the new approach, then deal with the implementation and computational scheme, and this is followed by examples to illustrate the new procedure.

Nonlinear approaches in engineering applications 2

CERN Document Server

Jazar, Reza N

2013-01-01

Provides updated principles and applications of the nonlinear approaches in solving engineering and physics problems Demonstrates how nonlinear approaches may open avenues to better, safer, cheaper systems with less energy consumption Has a strong emphasis on the application, physical meaning, and methodologies of nonlinear approaches in different engineering and science problems

Materiality in a Practice-Based Approach

Science.gov (United States)

Svabo, Connie

2009-01-01

Purpose: The paper aims to provide an overview of the vocabulary for materiality which is used by practice-based approaches to organizational knowing. Design/methodology/approach: The overview is theoretically generated and is based on the anthology Knowing in Organizations: A Practice-based Approach edited by Nicolini, Gherardi and Yanow. The…

Communicative Approaches To Teaching English in Namibia: The Issue of Transfer of Western Approaches To Developing Countries.

Science.gov (United States)

O'Sullivan, Margo C.

2001-01-01

Examines Namibia's communicative approach to teaching English speaking and listening skills by exploring the extent to which this approach is appropriate to the Namibian context. Raises the issue of transfer, specifically that communicative approaches are transferable to the Namibian context if they are simplified and adequate prescriptive…

Bibliography of Several Approaches to Rhetorical Criticism.

Science.gov (United States)

Benoit, William L.; Moeder, Michael D.

An illustrative rather than an exhaustive bibliography on approaches to rhetorical criticism, this update of an earlier publication lists more than 150 selections. The bibliography is divided into sections on: (1) discussions of the Burkean approach; (2) applications of the Burkean approach; (3) discussions of the fantasy theme approach; (4)…

Portfolio optimization using median-variance approach

Science.gov (United States)

Wan Mohd, Wan Rosanisah; Mohamad, Daud; Mohamed, Zulkifli

2013-04-01

Optimization models have been applied in many decision-making problems particularly in portfolio selection. Since the introduction of Markowitz's theory of portfolio selection, various approaches based on mathematical programming have been introduced such as mean-variance, mean-absolute deviation, mean-variance-skewness and conditional value-at-risk (CVaR) mainly to maximize return and minimize risk. However most of the approaches assume that the distribution of data is normal and this is not generally true. As an alternative, in this paper, we employ the median-variance approach to improve the portfolio optimization. This approach has successfully catered both types of normal and non-normal distribution of data. With this actual representation, we analyze and compare the rate of return and risk between the mean-variance and the median-variance based portfolio which consist of 30 stocks from Bursa Malaysia. The results in this study show that the median-variance approach is capable to produce a lower risk for each return earning as compared to the mean-variance approach.

Commercial dissemination approaches for solar home systems

Energy Technology Data Exchange (ETDEWEB)

Terrado, E.

1997-12-01

The author discusses the issue of providing solar home systems to primarily rural areas from the perspective of how to commercialize the process. He considers two different approaches, one an open market approach and the other an exclusive market approach. He describes examples of the exclusive market approach which are in process in Argentina and Brazil. Coming from a banking background, the business aspects are discussed in detail. He points out the strengths and weaknesses of both approaches toward developing such systems.

Islamic approach in counseling.

Science.gov (United States)

Hanin Hamjah, Salasiah; Mat Akhir, Noor Shakirah

2014-02-01

A religious approach is one of the matters emphasized in counseling today. Many researchers find that there is a need to apply the religious element in counseling because religion is important in a client's life. The purpose of this research is to identify aspects of the Islamic approach applied in counseling clients by counselors at Pusat Kaunseling Majlis Agama Islam Negeri Sembilan (PKMAINS). In addition, this research also analyses the Islamic approach applied in counseling at PKMAINS with reference to al-Quran and al-Sunnah. This is a qualitative research in the form of case study at PKMAINS. The main method used in this research is interview. The research instrument used is interview protocol. The respondents in this study include 9 counselors who serve in one of the counseling centers in Malaysia. This study also uses questionnaire as an additional instrument, distributed to 36 clients who receive counseling service at the center. The findings of the study show that the Islamic approach applied in counseling at PKMAINS may be categorized into three main aspects: aqidah (faith), ibadah (worship/ultimate devotion and love for God) and akhlaq (moral conduct). Findings also show that the counseling in these aspects is in line with Islamic teachings as contained in al-Quran and al-Sunnah.

Valuation: From The Discounted Cash Flows (DCF Approach To The Real Options Approach (ROA Valuation: From The Discounted Cash Flows (DCF Approach To The Real Options Approach (ROA

Directory of Open Access Journals (Sweden)

Cecilia Maya Ochoa

2004-12-01

Full Text Available There exists an abysm between market prices and traditional valuation approaches such as Discounted Cash Flows (DCF, a fact that neither academics nor practitioners could continue ignoring. Recently, a complementary approach has taken a foothold into the valuation world. Building on the DCF approach yet going further in the sense of incorporating flexibility in management investment decisions, and taking advantage of the advances in option pricing theory, the real options approach (ROA has become the alternative to capital budgeting and, lately, to corporate valuation. Empirical evidence shows that ROA explains actual prices better than DCF approaches and nowadays there is no question that from a theoretical point of view, ROA is a much more appealing concept than passive NPV. However, its acceptance by practitioners has been very slow due to the complexity of real options pricing.Existe un abismo entre precios de Mercado y la valoración estimada por métodos tradicionales tales como Flujos de Caja Descontados, un hecho que ni académicos ni practicantes pueden continuar ignorando. Recientemente, una metodología complementaria ha tomado gran fuerza. Partiendo de los Flujos de Caja Descontados, pero incorporando flexibilidad en las decisiones de inversión y aprovechando los avances en la teoría de valoración de opciones, el enfoque de opciones reales (ROA se ha convertido en la alternativa para presupuestación de capital y valoración de empresas. La evidencia empírica muestra que ROA explica los precios de mercado mejor que los enfoques basados en flujos de caja descontados y, hoy en día, no hay discusión de que es más atractivo desde un punto de vista teórico; sin embargo, su utilización en la práctica ha sido muy limitada debido a las dificultades que presenta la valoración de las opciones reales.

Risk communication: a mental models approach

National Research Council Canada - National Science Library

Morgan, M. Granger (Millett Granger)

2002-01-01

... information about risks. The procedure uses approaches from risk and decision analysis to identify the most relevant information; it also uses approaches from psychology and communication theory to ensure that its message is understood. This book is written in nontechnical terms, designed to make the approach feasible for anyone willing to try it. It is illustrat...

The enabling approach for housing supply

Directory of Open Access Journals (Sweden)

Ghada Farouk Hassan

2011-12-01

The paper attempts to highlight prerequisites needed to improve the success of the enabling approach in achieving adequate housing provision. Then the paper revisits the Egyptian experiences in the application of the enabling approach from 2005 till 2010. Finally, the paper highlights the main drops and lessons must be considered as promising approach after the revolution.

Unmanned Maritime Systems Incremental Acquisition Approach

Science.gov (United States)

2016-12-01

REPORT TYPE AND DATES COVERED MBA professional report 4. TITLE AND SUBTITLE UNMANNED MARITIME SYSTEMS INCREMENTAL ACQUISITION APPROACH 5. FUNDING...Approved for public release. Distribution is unlimited. UNMANNED MARITIME SYSTEMS INCREMENTAL ACQUISITION APPROACH Thomas Driscoll, Lieutenant...UNMANNED MARITIME SYSTEMS INCREMENTAL ACQUISITION APPROACH ABSTRACT The purpose of this MBA report is to explore and understand the issues

Extending cosmology: the metric approach

OpenAIRE

Mendoza, S.

2012-01-01

Comment: 2012, Extending Cosmology: The Metric Approach, Open Questions in Cosmology; Review article for an Intech "Open questions in cosmology" book chapter (19 pages, 3 figures). Available from: http://www.intechopen.com/books/open-questions-in-cosmology/extending-cosmology-the-metric-approach

Operations management approach to hospitals.

Science.gov (United States)

Harvey, J; Duguay, C R

1988-06-01

An operations management systems approach can be a useful tool for coordinating and planning in a complex organization. The authors argue for adapting such an approach to health care from the manufacturing industries in order to facilitate strategy formulation, communication and implementation.

Nonlinear Approaches in Engineering Applications

CERN Document Server

Jazar, Reza

2012-01-01

Nonlinear Approaches in Engineering Applications focuses on nonlinear phenomena that are common in the engineering field. The nonlinear approaches described in this book provide a sound theoretical base and practical tools to design and analyze engineering systems with high efficiency and accuracy and with less energy and downtime. Presented here are nonlinear approaches in areas such as dynamic systems, optimal control and approaches in nonlinear dynamics and acoustics. Coverage encompasses a wide range of applications and fields including mathematical modeling and nonlinear behavior as applied to microresonators, nanotechnologies, nonlinear behavior in soil erosion,nonlinear population dynamics, and optimization in reducing vibration and noise as well as vibration in triple-walled carbon nanotubes. This book also: Provides a complete introduction to nonlinear behavior of systems and the advantages of nonlinearity as a tool for solving engineering problems Includes applications and examples drawn from the el...

Abstract Cauchy problems three approaches

CERN Document Server

Melnikova, Irina V

2001-01-01

Although the theory of well-posed Cauchy problems is reasonably understood, ill-posed problems-involved in a numerous mathematical models in physics, engineering, and finance- can be approached in a variety of ways. Historically, there have been three major strategies for dealing with such problems: semigroup, abstract distribution, and regularization methods. Semigroup and distribution methods restore well-posedness, in a modern weak sense. Regularization methods provide approximate solutions to ill-posed problems. Although these approaches were extensively developed over the last decades by many researchers, nowhere could one find a comprehensive treatment of all three approaches.Abstract Cauchy Problems: Three Approaches provides an innovative, self-contained account of these methods and, furthermore, demonstrates and studies some of the profound connections between them. The authors discuss the application of different methods not only to the Cauchy problem that is not well-posed in the classical sense, b...

Global energy modeling - A biophysical approach

Energy Technology Data Exchange (ETDEWEB)

Dale, Michael

2010-09-15

This paper contrasts the standard economic approach to energy modelling with energy models using a biophysical approach. Neither of these approaches includes changing energy-returns-on-investment (EROI) due to declining resource quality or the capital intensive nature of renewable energy sources. Both of these factors will become increasingly important in the future. An extension to the biophysical approach is outlined which encompasses a dynamic EROI function that explicitly incorporates technological learning. The model is used to explore several scenarios of long-term future energy supply especially concerning the global transition to renewable energy sources in the quest for a sustainable energy system.

An approach to measurement

International Nuclear Information System (INIS)

Gudder, S.P.

1984-01-01

A new approach to measurement theory is presented. The definition of measurement is motivated by direct laboratory procedures as they are carried out in practice. The theory is developed within the quantum logic framework. The work clarifies an important problem in the quantum logic approach; namely, where the Hilbert space comes from. The relationship between measurements and observables is considered, and a Hilbert space embedding theorem is presented. Charge systems are also discussed. (author)

Exercising self-control increases approach motivation.

Science.gov (United States)

Schmeichel, Brandon J; Harmon-Jones, Cindy; Harmon-Jones, Eddie

2010-07-01

The present research tested the hypothesis that exercising self-control causes an increase in approach motivation. Study 1 found that exercising (vs. not exercising) self-control increases self-reported approach motivation. Study 2a identified a behavior--betting on low-stakes gambles--that is correlated with approach motivation but is relatively uncorrelated with self-control, and Study 2b observed that exercising self-control temporarily increases this behavior. Last, Study 3 found that exercising self-control facilitates the perception of a reward-relevant symbol (i.e., a dollar sign) but not a reward-irrelevant symbol (i.e., a percent sign). Altogether, these results support the hypothesis that exercising self-control temporarily increases approach motivation. Failures of self-control that follow from prior efforts at self-control (i.e., ego depletion) may be explained in part by increased approach motivation.

Vanpooling: the three major approaches

Energy Technology Data Exchange (ETDEWEB)

Sears, P.M.

1979-08-01

The manual provides technical assistance to existing or prospective vanpool sponsors. It is designed to help them promote vanpooling in its three major approaches: employer sponsored, third party sponsored, and driver owned and operated. The first chapter is an overview of vanpooling and a second chapter, on vanpool marketing, is addressed to ridesharing coordinators and others whose responsibilities include the promotion of vanpooling. Some fact sheets on the three approaches provide convenient summaries of the needs and opportunities of each approach and suggest solutions to practical problems likely to be encountered in starting new vanpool programs.

Approaches to ultrafast neutron detectors

International Nuclear Information System (INIS)

Wang, C.L.; Kalibjian, R.; Singh, M.S.

1984-01-01

We discuss two approaches to obtain detectors of very high temporal resolution. In the first approach, uranium-coated cathode is used in a streak tube configuration. Secondary electrons accompanying the fission fragments from a neutron-uranium reaction are accelerated, focussed and energy analyzed through a pinhole and streaked. Calculations show that 20 ps time-resolution can be obtained. In the second approach, a uranium-coated cathode is integrated into a transmission line. State-of-the-art technology indicates that time resolution of 20 ps can be obtained by gating the cathode with a fast electric pulse

A Novel Approach for Solving Semidefinite Programs

Directory of Open Access Journals (Sweden)

Hong-Wei Jiao

2014-01-01

Full Text Available A novel linearizing alternating direction augmented Lagrangian approach is proposed for effectively solving semidefinite programs (SDP. For every iteration, by fixing the other variables, the proposed approach alternatively optimizes the dual variables and the dual slack variables; then the primal variables, that is, Lagrange multipliers, are updated. In addition, the proposed approach renews all the variables in closed forms without solving any system of linear equations. Global convergence of the proposed approach is proved under mild conditions, and two numerical problems are given to demonstrate the effectiveness of the presented approach.

Psychoeducation for hypochondriasis : A comparison of a cognitive-behavioural approach and a problem-solving approach

NARCIS (Netherlands)

Buwalda, Femke M.; Bouman, Theo. K.; van Duijn, Marijtje A. J.; Van der Duin, M.

In this study, two 6-week psychoeducational courses for hypochondriasis are compared, one based on the cognitive-behavioural approach, and the other on the problem-solving approach. Effects of both courses on hypochondriacal complaints, depression, trait anxiety, and number of problems encountered

A systems approach to traditional oriental medicine

DEFF Research Database (Denmark)

Kim, Hyun Uk; Ryu, Jae Yong; Lee, Jong Ok

2015-01-01

Analyzing structural similarities between compounds derived from traditional oriental medicine and human metabolites is a systems-based approach that can help identify mechanisms of action and suggest approaches to reduce toxicity.......Analyzing structural similarities between compounds derived from traditional oriental medicine and human metabolites is a systems-based approach that can help identify mechanisms of action and suggest approaches to reduce toxicity....

Alternative Auditing Approaches

Energy Technology Data Exchange (ETDEWEB)

Kandt, Alicen J [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-15

This presentation for the 2017 Energy Exchange in Tampa, Florida, offers information about advanced auditing technologies and techniques including alternative auditing approaches and considerations and caveats.

The Knowledge Governance Approach

DEFF Research Database (Denmark)

Foss, Nicolai J.

with diverse capabilities of handling these transactions. Various open research issues that a knowledge governance approach may illuminate are sketched. Although knowledge governance draws clear inspiration from organizational economics and `rational' organization theory, it recognizes that knowledge......An attempt is made to characterize a `knowledge governance approach' as a distinctive, emerging field that cuts across the fields of knowledge management, organisation studies, strategy and human resource management. Knowledge governance is taken up with how the deployment of administrative...

Comparison of student's learning achievement through realistic mathematics education (RME) approach and problem solving approach on grade VII

Science.gov (United States)

Ilyas, Muhammad; Salwah

2017-02-01

The type of this research was experiment. The purpose of this study was to determine the difference and the quality of student's learning achievement between students who obtained learning through Realistic Mathematics Education (RME) approach and students who obtained learning through problem solving approach. This study was a quasi-experimental research with non-equivalent experiment group design. The population of this study was all students of grade VII in one of junior high school in Palopo, in the second semester of academic year 2015/2016. Two classes were selected purposively as sample of research that was: year VII-5 as many as 28 students were selected as experiment group I and VII-6 as many as 23 students were selected as experiment group II. Treatment that used in the experiment group I was learning by RME Approach, whereas in the experiment group II by problem solving approach. Technique of data collection in this study gave pretest and posttest to students. The analysis used in this research was an analysis of descriptive statistics and analysis of inferential statistics using t-test. Based on the analysis of descriptive statistics, it can be concluded that the average score of students' mathematics learning after taught using problem solving approach was similar to the average results of students' mathematics learning after taught using realistic mathematics education (RME) approach, which are both at the high category. In addition, It can also be concluded that; (1) there was no difference in the results of students' mathematics learning taught using realistic mathematics education (RME) approach and students who taught using problem solving approach, (2) quality of learning achievement of students who received RME approach and problem solving approach learning was same, which was at the high category.

Analyzing public health policy: three approaches.

Science.gov (United States)

Coveney, John

2010-07-01

Policy is an important feature of public and private organizations. Within the field of health as a policy arena, public health has emerged in which policy is vital to decision making and the deployment of resources. Public health practitioners and students need to be able to analyze public health policy, yet many feel daunted by the subject's complexity. This article discusses three approaches that simplify policy analysis: Bacchi's "What's the problem?" approach examines the way that policy represents problems. Colebatch's governmentality approach provides a way of analyzing the implementation of policy. Bridgman and Davis's policy cycle allows for an appraisal of public policy development. Each approach provides an analytical framework from which to rigorously study policy. Practitioners and students of public health gain much in engaging with the politicized nature of policy, and a simple approach to policy analysis can greatly assist one's understanding and involvement in policy work.

Experimental design research approaches, perspectives, applications

CERN Document Server

Stanković, Tino; Štorga, Mario

2016-01-01

This book presents a new, multidisciplinary perspective on and paradigm for integrative experimental design research. It addresses various perspectives on methods, analysis and overall research approach, and how they can be synthesized to advance understanding of design. It explores the foundations of experimental approaches and their utility in this domain, and brings together analytical approaches to promote an integrated understanding. The book also investigates where these approaches lead to and how they link design research more fully with other disciplines (e.g. psychology, cognition, sociology, computer science, management). Above all, the book emphasizes the integrative nature of design research in terms of the methods, theories, and units of study—from the individual to the organizational level. Although this approach offers many advantages, it has inherently led to a situation in current research practice where methods are diverging and integration between individual, team and organizational under...

Introduction to Approaches in Music Therapy. Second Edition

Science.gov (United States)

Darrow, Alice Ann, Ed.

2008-01-01

The second edition of "Introduction to Approaches in Music Therapy" includes a new introductory chapter that addresses historical perspectives on the approaches, a rationale for the categorization of approaches, and discussion on professional issues related to the use of these approaches. Each of the chapters addressing approaches includes updated…

Approaching a Postcolonial Arctic

DEFF Research Database (Denmark)

Jensen, Lars

2016-01-01

This article explores different postcolonially configured approaches to the Arctic. It begins by considering the Arctic as a region, an entity, and how the customary political science informed approaches are delimited by their focus on understanding the Arctic as a region at the service...... of the contemporary neoliberal order. It moves on to explore how different parts of the Arctic are inscribed in a number of sub-Arctic nation-state binds, focusing mainly on Canada and Denmark. The article argues that the postcolonial can be understood as a prism or a methodology that asks pivotal questions to all...... approaches to the Arctic. Yet the postcolonial itself is characterised by limitations, not least in this context its lack of interest in the Arctic, and its bias towards conventional forms of representation in art. The article points to the need to develop a more integrated critique of colonial and neo...

Fluoroscopically-Guided Posterior Approach for Shoulder Magnetic Resonance Arthrography: Comparison with Conventional Anterior Approach

International Nuclear Information System (INIS)

Yoo, Koun J.; Ha, Doo Hoe; Lee, Sang Min

2011-01-01

To prospectively evaluate the usefulness of the fluoroscopically-guided posterior approach compared with the anterior approach for shoulder magnetic resonance(MR) arthrography. Institutional review board approval and informed consent were obtained. Among 60 shoulder MR arthrographies performed on 59 patients with symptomatic shoulders, an intra-articular injection was performed (30 cases using the anterior approach and 30 using the posterior approach). Procedure-related pain was assessed by using a 5 score visual analogue scale (VAS). Depth of the puncture and standardized depth of puncture by body mass index (BMI) were recorded. The contrast leakage along the course of the puncture was evaluated by reviewing the MR. The statistical analyses included the Mann-Whitney U and Kruskal-Wallis test. There was no significant difference in VAS scores between the anterior and posterior groups (1.77 ± 1.10 vs. 1.80 ± 0.96). Depth of puncture and standardized depth of puncture by BMI were significantly shorter in the posterior group than those in the anterior group (4.4 ± 0.8 cm and 1.8 ± 0.3 cm vs. 6.6 ± 0.9 cm and 2.8 ± 0.4 cm, p < 0.001), respectively. The incidence of contrast leakage was more frequent in the posterior group (p = 0.003). The posterior approach will be useful in shoulder MR arthrography with a suspected anterior pathology, a postoperative follow-up study or obese patient.

Heuristic Approach for Balancing Shift Schedules

International Nuclear Information System (INIS)

Kim, Dae Ho; Yun, Young Su; Lee, Yong Hee

2005-01-01

In this paper, a heuristic approach for balancing shift schedules is proposed. For the shift schedules, various constraints which have usually been considered in realworld industry are used, and the objective is to minimize the differences of the workloads in each workgroup. The constraints and objective function are implemented in the proposed heuristic approach. Using a simple instance, the efficiency of the proposed heuristic approach is proved

The pulling power of chocolate: Effects of approach-avoidance training on approach bias and consumption.

Science.gov (United States)

Dickson, Hugh; Kavanagh, David J; MacLeod, Colin

2016-04-01

Previous research has shown that action tendencies to approach alcohol may be modified using computerized Approach-Avoidance Task (AAT), and that this impacted on subsequent consumption. A recent paper in this journal (Becker, Jostman, Wiers, & Holland, 2015) failed to show significant training effects for food in three studies: Nor did it find effects on subsequent consumption. However, avoidance training to high calorie foods was tested against a control rather than Approach training. The present study used a more comparable paradigm to the alcohol studies. It randomly assigned 90 participants to 'approach' or 'avoid' chocolate images on the AAT, and then asked them to taste and rate chocolates. A significant interaction of condition and time showed that training to avoid chocolate resulted in faster avoidance responses to chocolate images, compared with training to approach it. Consistent with Becker et al.'s Study 3, no effect was found on amounts of chocolate consumed, although a newly published study in this journal (Schumacher, Kemps, & Tiggemann, 2016) did do so. The collective evidence does not as yet provide solid basis for the application of AAT training to reduction of problematic food consumption, although clinical trials have yet to be conducted. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Site Approach - Lessons Learned from the Integrated Safeguards Approach for JNC-1

International Nuclear Information System (INIS)

Kikuchi, M.; Iso, S.; Tomine, K.; Hirato, Y.; Namekawa, M.; Takasugi, N.; Watanabe, M.; Tsutaki, Y.; Asano, T.; Nagatani, T.; Ninagawa, J.; Fujiwara, S.; Takahashi, S.; Kimura, T.; Kodani, Y.; Fukuhara, J.; Miyaji, N.; Kawakami, Y.; Koizumi, A.; Yamazaki, Y.; Nishinosono, S.; Sasaki, K.

2010-01-01

Integrated safeguards approaches for specific sites are recognized important elements in the design of a State-level approach under the concept of grouping facilities. Japan and the IAEA agreed further improvement of integrated safeguards implementation in effective and efficient manner, particularly at large complex nuclear sites in Japan. Japan and the IAEA developed the integrated safeguards approach for specific sites defined at Article 18 of Additional Protocol. In 2008, the IAEA started the three-year test implementation of JNC-1 site approach for improving the effectiveness and efficiency of the safeguards implementation of UDU material handling facilities. Japan and IAEA agreed to adopt the sector concept in order to make clear of subjected nuclear material to be verified. The sector is defined as spatial assignment that treats the same material stratum beyond MBAs in the site. The arrangement of MBAs and related material balance calculations as well as statistical analysis is maintained as a fundamental safeguards measure. At the boundaries of each sector, appropriate unattended NDA system and/or C/S system are installed, and material flows across the boundaries are verified by the system or attendance of resident inspectors. For inventory verification of the nuclear material stayed in sectors, an appropriate numbers of randomly scheduled inspections will be implemented. IAEA can access to the randomly selected sectors within 2 hours after notification. NRTA based on frequent operator's declaration will be performed for achievement of timeliness detection goal. The JNC-1 site approach has been implemented under the enhanced co-operation between the IAEA and SSAC through joint use of equipment and arrangements for DA analysis. Especially, national inspectors are working with IAEA together for coordination with operators. Because NMCC lab analyses all DA samples taken from facilities and the analysis results will be shared by the IAEA, certain numbers of DA

Developing a Dual-Level Capabilities Approach: Using Constructivist Grounded Theory and Feminist Ethnography to Enhance the Capabilities Approaches

Science.gov (United States)

Hall, Kia M. Q.

2014-01-01

In this study, a dual-level capabilities approach to development is introduced. This approach intends to improve upon individual-focused capabilities approaches developed by Amartya Sen and Martha Nussbaum. Based upon seven months of ethnographic research in the Afro-descendant, autochthonous Garifuna community of Honduras, constructivist grounded…

Approaches to Scandinavian Crime Fiction

DEFF Research Database (Denmark)

Agger, Gunhild

2010-01-01

as the approach of genre typology and the concept of evil – seemingly disparate concepts and approaches, but all related to the complex processes in the borderlands between crime fiction and society. Using examples from Scandinavian crime fiction, I discuss whether the growing proximity to international genres......The working paper discusses some of the major approaches to Scandinavian crime fiction in the light of the dominant features of crime culture, e.g. the broad exposure of crime fiction via different platforms and media. In this connection, the concept of mediatization is considered as well......, ways of production and standards increasingly removes Scandinavian crime fiction from its original attractions or not....

Cognitive Approaches to Automated Instruction.

Science.gov (United States)

Regian, J. Wesley, Ed.; Shute, Valerie J., Ed.

This book contains a snapshot of state-of-the-art research on the design of automated instructional systems. Selected cognitive psychologists were asked to describe their approach to instruction and cognitive diagnosis, the theoretical basis of the approach, its utility and applicability, and the knowledge engineering or task analysis methods…

The CAPM approach to materiality

OpenAIRE

Hadjieftychiou, Aristarchos

1993-01-01

Materiality is a pervasive accounting concept that has defied a precise quantitative definition. The Capital Asset Pricing Model (CAPM) approach to materiality provides a means for determining the limits that bound materiality. Also, the approach makes it possible to locate the point estimate within these limits based on certain assumptions.

A Posteriori Approach for Community Detection

Institute of Scientific and Technical Information of China (English)

Chuan Shi; Zhen-Yu Yan; Xin Pan; Ya-Nan Cai; Bin Wu

2011-01-01

Conventional community detection approaches in complex network are based on the optimization of a priori decision,i.e.,a single quality function designed beforehand.This paper proposes a posteriori decision approach for community detection.The approach includes two phases:in the search phase,a special multi-objective evolutionary algorithm is designed to search for a set of tradeoff partitions that reveal the community structure at different scales in one run; in the decision phase,three model selection criteria and the Possibility Matrix method are proposed to aid decision makers to select the preferable solutions through differentiating the set of optimal solutions according to their qualities.The experiments in five synthetic and real social networks illustrate that,in one run,our method is able to obtain many candidate solutions,which effectively avoids the resolution limit existing in priori decision approaches.In addition,our method can discover more authentic and comprehensive community structures than those priori decision approaches.

An Ethnografic Approach to Video Analysis

DEFF Research Database (Denmark)

Holck, Ulla

2007-01-01

The overall purpose in the ethnographic approach to video analysis is to become aware of implicit knowledge in those being observed. That is, knowledge that cannot be acquired through interviews. In music therapy this approach can be used to analyse patterns of interaction between client and ther......: Methods, Techniques and Applications in Music Therapy for Music Therapy Clinicians, Educators, Researchers and Students. London: Jessica Kingsley.......The overall purpose in the ethnographic approach to video analysis is to become aware of implicit knowledge in those being observed. That is, knowledge that cannot be acquired through interviews. In music therapy this approach can be used to analyse patterns of interaction between client...... a short introduction to the ethnographic approach, the workshop participants will have a chance to try out the method. First through a common exercise and then applied to video recordings of music therapy with children with severe communicative limitations. Focus will be on patterns of interaction...

A Multi-Model Approach for System Diagnosis

DEFF Research Database (Denmark)

Niemann, Hans Henrik; Poulsen, Niels Kjølstad; Bækgaard, Mikkel Ask Buur

2007-01-01

A multi-model approach for system diagnosis is presented in this paper. The relation with fault diagnosis as well as performance validation is considered. The approach is based on testing a number of pre-described models and find which one is the best. It is based on an active approach......,i.e. an auxiliary input to the system is applied. The multi-model approach is applied on a wind turbine system....

Lipoma do ângulo pontocerebelar: relato de caso Lipoma of the cerebellopontine angle: case report

Directory of Open Access Journals (Sweden)

WALTER JOSÉ FAGUNDES-PEREYRA

2000-09-01

Full Text Available Os lipomas do ângulo pontocerebelar são tumores muito raros. Em geral são assintomáticos, achados fortuitos em autópsia, tomografia computadorizada (TC de crânio ou ressonância nuclear magnética do encéfalo. Os autores apresentam o caso de paciente, feminina, branca, 14 anos, há três anos com diminuição da audição à esquerda e há um ano com cefaléia, tipo hemicrânia à esquerda. A TC de crânio evidenciou lesão hipodensa, sem captação de contraste, no ângulo pontocerebelar esquerdo. A paciente foi submetida a cirurgia por via retrossigmóidea para abordagem da lesão, que se apresentou de coloração amarelada, característica de tecido adiposo. Tendo em vista o envolvimento de estruturas nervosas (VII e VIII nervos cranianos, optou-se pela exérese parcial da lesão. A paciente evoluiu com melhora da cefaléia, sem piora do déficit auditivo. Após três anos de seguimento, mantém o quadro estável. Conclui-se que os lipomas do ângulo pontocerebelar, quando assintomáticos, podem ser tratados conservadoramente. Entretanto aqueles associados a sintomatologia persistente e progressiva devem ser operados. A exérese total ou parcial vai depender do envolvimento ou não das estruturas neurovasculares adjacentes.Lipoma of the cerebellopontine angle is a very rare tumor. We report the case of a 14-years-old female, with left side deafness during three years, associated with headache. CT scan showed an hypodense mass, without enhancement at the cerebellopontine angle. The patient was treated surgically by left retrosigmoid approach. The lesion involved the eighth and seventh cranial nerves and only a partial removal was performed. The postoperative course was uneventful. She had no more headache; the deafness of the left side remained unchanged. Asymptomatic lipoma of the cerebellopontine angle can be treated conservatively, although those with progressive symptoms should be treated surgically, with total or partial remove

The PNEI holistic approach in coloproctology.

Science.gov (United States)

Pescatori, M; Podzemny, V; Pescatori, L C; Dore, M P; Bassotti, G

2015-05-01

The psycho-neuroendocrine-immune approach relies on the concept of considering diseases from a holistic point of view: the various components (psyche, nervous system, endocrine system, and immune system) control the diseased organ/apparatus and in turn are influenced by a feedback mechanism. In this article, we will consider the psycho-neuroendocrine-immune approach to coloproctological disorders, by providing clinical cases and discussing them in light of this approach.

A NEW APPROACH TO VIRTUAL EDUCATION

Directory of Open Access Journals (Sweden)

Vladimir V. Kureychik

2014-01-01

Full Text Available The article discusses several approaches to training, namely the virtual. Concrete examples of virtual learning systems were described, we disclosed their features, advantages and disadvantages. A new suggested approach integrates the features of existing systems, and opens new horizons and opportunities to obtain certain skills and abilities. Introduction of a new approach to the educational process will improve the quality and effectiveness of learning. 

Science based integrated approach to advanced nuclear fuel development - vision, approach, and overview

Energy Technology Data Exchange (ETDEWEB)

Unal, Cetin [Los Alamos National Laboratory; Pasamehmetoglu, Kemal [IDAHO NATIONAL LAB; Carmack, Jon [IDAHO NATIONAL LAB

2010-01-01

Advancing the performance of Light Water Reactors, Advanced Nuclear Fuel Cycles, and Advanced Rcactors, such as the Next Generation Nuclear Power Plants, requires enhancing our fundamental understanding of fuel and materials behavior under irradiation. The capability to accurately model the nuclear fuel systems is critical. In order to understand specific aspects of the nuclear fuel, fully coupled fuel simulation codes are required to achieve licensing of specific nuclear fuel designs for operation. The backbone of these codes, models, and simulations is a fundamental understanding and predictive capability for simulating the phase and microstructural behavior of the nuclear fuel system materials and matrices. The purpose of this paper is to identify the modeling and simulation approach in order to deliver predictive tools for advanced fuels development. The coordination between experimental nuclear fuel design, development technical experts, and computational fuel modeling and simulation technical experts is a critical aspect of the approach and naturally leads to an integrated, goal-oriented science-based R & D approach and strengthens both the experimental and computational efforts. The Advanced Fuels Campaign (AFC) and Nuclear Energy Advanced Modeling and Simulation (NEAMS) Fuels Integrated Performance and Safety Code (IPSC) are working together to determine experimental data and modeling needs. The primary objective of the NEAMS fuels IPSC project is to deliver a coupled, three-dimensional, predictive computational platform for modeling the fabrication and both normal and abnormal operation of nuclear fuel pins and assemblies, applicable to both existing and future reactor fuel designs. The science based program is pursuing the development of an integrated multi-scale and multi-physics modeling and simulation platform for nuclear fuels. This overview paper discusses the vision, goals and approaches how to develop and implement the new approach.

Science based integrated approach to advanced nuclear fuel development - vision, approach, and overview

International Nuclear Information System (INIS)

Unal, Cetin; Pasamehmetoglu, Kemal; Carmack, Jon

2010-01-01

Advancing the performance of Light Water Reactors, Advanced Nuclear Fuel Cycles, and Advanced Rcactors, such as the Next Generation Nuclear Power Plants, requires enhancing our fundamental understanding of fuel and materials behavior under irradiation. The capability to accurately model the nuclear fuel systems is critical. In order to understand specific aspects of the nuclear fuel, fully coupled fuel simulation codes are required to achieve licensing of specific nuclear fuel designs for operation. The backbone of these codes, models, and simulations is a fundamental understanding and predictive capability for simulating the phase and microstructural behavior of the nuclear fuel system materials and matrices. The purpose of this paper is to identify the modeling and simulation approach in order to deliver predictive tools for advanced fuels development. The coordination between experimental nuclear fuel design, development technical experts, and computational fuel modeling and simulation technical experts is a critical aspect of the approach and naturally leads to an integrated, goal-oriented science-based R and D approach and strengthens both the experimental and computational efforts. The Advanced Fuels Campaign (AFC) and Nuclear Energy Advanced Modeling and Simulation (NEAMS) Fuels Integrated Performance and Safety Code (IPSC) are working together to determine experimental data and modeling needs. The primary objective of the NEAMS fuels IPSC project is to deliver a coupled, three-dimensional, predictive computational platform for modeling the fabrication and both normal and abnormal operation of nuclear fuel pins and assemblies, applicable to both existing and future reactor fuel designs. The science based program is pursuing the development of an integrated multi-scale and multi-physics modeling and simulation platform for nuclear fuels. This overview paper discusses the vision, goals and approaches how to develop and implement the new approach.

APPROACHES FOR SUSTAINABLE MANUFACTURING

Institute of Scientific and Technical Information of China (English)

G(U)NTHER Seliger; SEBASTIAN Kernbaum; MARCO Zettl

2007-01-01

Sustainable development is a holistic approach harmonizing ecological, economical and socio-political needs with respect to the superior objective of enhancing human living standards. Thereby the availability of natural resources and the conservation of the ecosystems have to be considered that future generations have the possibility to meet their own needs. A long-term economical development demands the transition from a source-sink economy to a cycle economy as a result of limited resources, limited environmental capacities to absorb waste and emissions as well as increasing needs of a growing population. A reference model for sustainability in manufacturing is presented and used to illustrate sustainable approaches with respect to management, technology, process and product. Adaptation of products and components is a vital element for supporting efficient reuse of products and components. Consequently adaptation contributes to the ambitious goals of sustainability. Technological enablers for adaptation as modularity, information and communication technology are exemplarily introduced. Moreover, approaches for disseminating knowledge in sustainability are given.

Hybrid biasing approaches for global variance reduction

International Nuclear Information System (INIS)

Wu, Zeyun; Abdel-Khalik, Hany S.

2013-01-01

A new variant of Monte Carlo—deterministic (DT) hybrid variance reduction approach based on Gaussian process theory is presented for accelerating convergence of Monte Carlo simulation and compared with Forward-Weighted Consistent Adjoint Driven Importance Sampling (FW-CADIS) approach implemented in the SCALE package from Oak Ridge National Laboratory. The new approach, denoted the Gaussian process approach, treats the responses of interest as normally distributed random processes. The Gaussian process approach improves the selection of the weight windows of simulated particles by identifying a subspace that captures the dominant sources of statistical response variations. Like the FW-CADIS approach, the Gaussian process approach utilizes particle importance maps obtained from deterministic adjoint models to derive weight window biasing. In contrast to the FW-CADIS approach, the Gaussian process approach identifies the response correlations (via a covariance matrix) and employs them to reduce the computational overhead required for global variance reduction (GVR) purpose. The effective rank of the covariance matrix identifies the minimum number of uncorrelated pseudo responses, which are employed to bias simulated particles. Numerical experiments, serving as a proof of principle, are presented to compare the Gaussian process and FW-CADIS approaches in terms of the global reduction in standard deviation of the estimated responses. - Highlights: ► Hybrid Monte Carlo Deterministic Method based on Gaussian Process Model is introduced. ► Method employs deterministic model to calculate responses correlations. ► Method employs correlations to bias Monte Carlo transport. ► Method compared to FW-CADIS methodology in SCALE code. ► An order of magnitude speed up is achieved for a PWR core model.

Complementarities of two existing intermediate conservation approaches

Directory of Open Access Journals (Sweden)

Sergei Volis

2017-12-01

Full Text Available The need for integration of ex situ and in situ approaches in conservation of plants has long been recognized. However, ex situ collections have numerous limitations that reduce their utility for conservation, necessitating the introduction of new, more appropriate, flexible and less costly approaches. Two new approaches that can be called “intermediate” between in situ and ex situ, and bridging them in some way have been proposed over the last two decades. In these approaches material collected in natural populations is planted and maintained outside the original location, but with a different purpose. While the purpose of the inter situs approach is reintroduction, the concern of the quasi in situ approach is long-term storage of species genetic diversity. I view these two approaches as complementary and necessary components of conservation-oriented restoration. In restoration of a degraded habitat using threatened species (i.e. inter situs, quasi in situ collections can serve an important role in providing long-term preservation of these species’ genetic diversity and production of seeds needed for restoration.

Childhood obesity: Current and novel approaches.

Science.gov (United States)

Sabin, Matthew A; Kiess, Wieland

2015-06-01

The prevalence of childhood obesity has increased over the last fifty years by approximately 5% per decade, and approximately a quarter of all children are now either overweight or obese. These children have a significantly increased risk of many future health problems including adult obesity, type 2 diabetes and heart disease. Despite this relentless increase, common-sense approaches aimed at prevention and treatment have failed to solve the problem. Current approaches at prevention have faced major challenges with some progress in implementing smaller scale programs and social marketing, but little action on broad public policy approaches which often appears unpalatable to society or individual governments. Meanwhile, treatment approaches have mainly focused on lifestyle change, and novel approaches are urgently needed. Prevention needs to shift to improving maternal health prior to conception, with more research focussed on the impact of early years in programming offspring to future overweight/obesity. Likewise, treatment paradigms need to move from simply thinking that obesity can be solved by readdressing diet and activity levels. Novel approaches are needed which take into consideration the complex physiology which regulates early childhood growth and the development of obesity in susceptible individuals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Capability approach

DEFF Research Database (Denmark)

Jensen, Niels Rosendal; Kjeldsen, Christian Christrup

Lærebogen er den første samlede danske præsentation af den af Amartya Sen og Martha Nussbaum udviklede Capability Approach. Bogen indeholder en præsentation og diskussion af Sen og Nussbaums teoretiske platform. I bogen indgår eksempler fra såvel uddannelse/uddannelsespolitik, pædagogik og omsorg....

RNA/PNA Approach

Indian Academy of Sciences (India)

In this approach we want to develop structural analogue of the leader that might have higher affinity towards the Phosphoprotein, but would impair the dimerization process and viral leader RNA binding.

Why do fearful facial expressions elicit behavioral approach? Evidence from a combined approach-avoidance implicit association test.

Science.gov (United States)

Hammer, Jennifer L; Marsh, Abigail A

2015-04-01

Despite communicating a "negative" emotion, fearful facial expressions predominantly elicit behavioral approach from perceivers. It has been hypothesized that this seemingly paradoxical effect may occur due to fearful expressions' resemblance to vulnerable, infantile faces. However, this hypothesis has not yet been tested. We used a combined approach-avoidance/implicit association test (IAT) to test this hypothesis. Participants completed an approach-avoidance lever task during which they responded to fearful and angry facial expressions as well as neutral infant and adult faces presented in an IAT format. Results demonstrated an implicit association between fearful facial expressions and infant faces and showed that both fearful expressions and infant faces primarily elicit behavioral approach. The dominance of approach responses to both fearful expressions and infant faces decreased as a function of psychopathic personality traits. Results suggest that the prosocial responses to fearful expressions observed in most individuals may stem from their associations with infantile faces. (PsycINFO Database Record (c) 2015 APA, all rights reserved).

Classical approach in atomic physics

International Nuclear Information System (INIS)

Solov'ev, E.A.

2011-01-01

The application of a classical approach to various quantum problems - the secular perturbation approach to quantization of a hydrogen atom in external fields and a helium atom, the adiabatic switching method for calculation of a semiclassical spectrum of a hydrogen atom in crossed electric and magnetic fields, a spontaneous decay of excited states of a hydrogen atom, Gutzwiller's approach to Stark problem, long-lived excited states of a helium atom discovered with the help of Poincare section, inelastic transitions in slow and fast electron-atom and ion-atom collisions - is reviewed. Further, a classical representation in quantum theory is discussed. In this representation the quantum states are treated as an ensemble of classical states. This approach opens the way to an accurate description of the initial and final states in classical trajectory Monte Carlo (CTMC) method and a purely classical explanation of tunneling phenomenon. The general aspects of the structure of the semiclassical series such as renormalization group symmetry, criterion of accuracy and so on are reviewed as well. (author)

Science Education: Issues, Approaches and Challenges

Directory of Open Access Journals (Sweden)

Shairose Irfan Jessani

2015-06-01

Full Text Available In today’s global education system, science education is much more than fact-based knowledge. Science education becomes meaningless and incomprehensible for learners, if the learners are unable to relate it with their lives. It is thus recommended that Pakistan, like many other countries worldwide should adopt Science Technology Society (STS approach for delivery of science education. The purpose of the STS approach lies in developing scientifically literate citizens who can make conscious decisions about the socio-scientific issues that impact their lives. The challenges in adopting this approach for Pakistan lie in four areas that will completely need to be revamped according to STS approach. These areas include: the examination system; science textbooks; science teacher education programs; and available resources and school facilities.

Artificial intelligence approaches in statistics

International Nuclear Information System (INIS)

Phelps, R.I.; Musgrove, P.B.

1986-01-01

The role of pattern recognition and knowledge representation methods from Artificial Intelligence within statistics is considered. Two areas of potential use are identified and one, data exploration, is used to illustrate the possibilities. A method is presented to identify and separate overlapping groups within cluster analysis, using an AI approach. The potential of such ''intelligent'' approaches is stressed

Homogenization approach in engineering

International Nuclear Information System (INIS)

Babuska, I.

1975-10-01

Homogenization is an approach which studies the macrobehavior of a medium by its microproperties. Problems with a microstructure play an essential role in such fields as mechanics, chemistry, physics, and reactor engineering. Attention is concentrated on a simple specific model problem to illustrate results and problems typical of the homogenization approach. Only the diffusion problem is treated here, but some statements are made about the elasticity of composite materials. The differential equation is solved for linear cases with and without boundaries and for the nonlinear case. 3 figures, 1 table

The observational approach in environmental restoration

International Nuclear Information System (INIS)

Smyth, J.D.; Quinn, R.D.

1991-07-01

The US Department of Energy (DOE) has committed to completing environmental restoration of its facilities within the next 28 years (DOE 1990b). In order to achieve this, DOE must ensure that its restoration activities are both effective and efficient. A key aspect of fulfilling this commitment is the recognition and management of uncertainty that is inherent in waste-site clean-up actions. The DOE Office of Environmental Restoration (DOE-ER) requested Pacific Northwest Laboratory (PNL) to investigate the applicability and implementation of what is known as the ''observational approach'' to better address these needs. PNL's initial investigation resulted in the positive conclusion that the observational approach had potential benefit to DOE during environmental restoration. In a follow-on effort, PNL supported by CH2M HILL, has been providing guidance to DOE field-offices on observational approach fundamentals, implementation, and application to waste-site remediation. This paper outlines the fundamentals of the observational approach and discusses the progress in integrating the observational approach in DOE's environmental restoration efforts. 9 refs., 2 figs

An Effective Approach to Teaching Electrochemistry.

Science.gov (United States)

Birss, Viola I.; Truax, D. Rodney

1990-01-01

An approach which may be useful for teaching electrochemistry in freshman college chemistry courses is presented. Discussed are the potential problems with teaching this subject and solutions provided by this approach. (CW)

A Systems Approach to Developing an Affordable Space Ground Transportation Architecture using a Commonality Approach

Science.gov (United States)

Garcia, Jerry L.; McCleskey, Carey M.; Bollo, Timothy R.; Rhodes, Russel E.; Robinson, John W.

2012-01-01

This paper presents a structured approach for achieving a compatible Ground System (GS) and Flight System (FS) architecture that is affordable, productive and sustainable. This paper is an extension of the paper titled "Approach to an Affordable and Productive Space Transportation System" by McCleskey et al. This paper integrates systems engineering concepts and operationally efficient propulsion system concepts into a structured framework for achieving GS and FS compatibility in the mid-term and long-term time frames. It also presents a functional and quantitative relationship for assessing system compatibility called the Architecture Complexity Index (ACI). This paper: (1) focuses on systems engineering fundamentals as it applies to improving GS and FS compatibility; (2) establishes mid-term and long-term spaceport goals; (3) presents an overview of transitioning a spaceport to an airport model; (4) establishes a framework for defining a ground system architecture; (5) presents the ACI concept; (6) demonstrates the approach by presenting a comparison of different GS architectures; and (7) presents a discussion on the benefits of using this approach with a focus on commonality.

A Humanistic Approach to South African Accounting Education

Science.gov (United States)

West, A.; Saunders, S.

2006-01-01

Humanistic psychologist Carl Rogers made a distinction between traditional approaches and humanistic "learner-centred" approaches to education. The traditional approach holds that educators impart their knowledge to willing and able recipients; whereas the humanistic approach holds that educators act as facilitators who assist learners…

Differentiating Performance Approach Goals and Their Unique Effects

Science.gov (United States)

Edwards, Ordene V.

2014-01-01

The study differentiates between two types of performance approach goals (competence demonstration performance approach goal and normative performance approach goal) by examining their unique effects on self-efficacy, interest, and fear of failure. Seventy-nine students completed questionnaires that measure performance approach goals,…

The Hermeneutical Approach in Translation Studies

Directory of Open Access Journals (Sweden)

Bernd Stefanink

2017-09-01

Full Text Available Our aim is to convince the reader of the validity of the hermeneutical approach in translation studies. In a first part, we will show that this validity is based on the fact that the hermeneutical approach integrates factors like subjectivity, intuition, corporeality and creativity in its theoretical reflection, being thus close to the reality of the translation process. In a second part, we will situate this approach in the context of the development of modern translation studies since the 1950s, and show that this development was characterized by a dominating tendency that led from an atomistic to a more and more holistic view of the translation unit, legitimating the holistic approach, which is fundamental in translational hermeneutics. Our third part relates the history of philosophical hermeneutics as the legitimate foundation of translational hermeneutics. In a fourth part, devoted to the “outcoming perspectives”, we will try to reinforce the legitimacy of the hermeneutical approach by showing how it is supported by recent results of research in cognitive science. In order to foster further research in translational hermeneutics we also offer a methodology based on hermeneutic principles to study the translation process. Finally, we give an example of legitimation of a creative problemsolving based on a hermeneutical approach of a translation problem which finds its validation in the results of cognitive research.

Anti-glomerular basement membrane autoantibodies in the Brown Norway rat: detection by a solid-phase radioimmunoassay

International Nuclear Information System (INIS)

Bowman, C.; Peters, D.K.; Lockwood, C.M.

1983-01-01

A solid-phase radioimmunoassay (RIA) is described for the detection of IgG autoantibodies to glomerular basement membrane (GBM) induced in the Brown Norway rat by mercuric chloride. The assay involves the adsorption of a collagenase digest of GBM to plastic microtitre plates and detection of bound antibody with affinity purified radiolabelled rabbit anti-rat IgG. Comparison with existing immunofluorescence methods for detection of anti-GBM antibody showed that the solid-phase RIA is highly sensitive, allowing detection of antibody in solutions with as low as 0.5 ng protein/ml. The assay is suitable for detection of anti-GBM antibody both in serum and in eluates from nephritic kidneys. The assay proved to be specific in competitive studies of inhibition brought about by GBM, keyhole limpet antigen and ovalbumin. This solid-phase RIA is reproducible, robust and easy to perform. (Auth.)

A polyvalent vaccine for high-risk prostate patients: "are more antigens better?"

DEFF Research Database (Denmark)

Slovin, Susan F; Ragupathi, Govind; Fernandez, Celina

2007-01-01

vaccine of synthetic "self" antigens broke immunologic tolerance against two or more antigens in all 30 vaccinated patients, was safe, but antibody titers against several of the antigens were lower than those seen in individual monovalent trials. No impact on PSA slope was detected. We address......We have shown the immunogenicity and safety of synthetic carbohydrate vaccines when conjugated to the carrier keyhole limpet hemocyanin (KLH) and given with the adjuvant, QS-21, in patients with biochemically relapsed prostate cancer. To determine whether immune response could be further enhanced...... and mixed with QS-21. Eight vaccinations were administered over 13 months. All 30 patients had significant elevations in antibody titers to at least two of the six antigens; 22 patients had increased reactivity with FACS. These serologic responses were lower than that seen previously in patients treated...

Removal of symptomatic craniofacial titanium hardware following craniotomy: Case series and review

Directory of Open Access Journals (Sweden)

Sheri K. Palejwala

2015-06-01

Full Text Available Titanium craniofacial hardware has become commonplace for reconstruction and bone flap fixation following craniotomy. Complications of titanium hardware include palpability, visibility, infection, exposure, pain, and hardware malfunction, which can necessitate hardware removal. We describe three patients who underwent craniofacial reconstruction following craniotomies for trauma with post-operative courses complicated by medically intractable facial pain. All three patients subsequently underwent removal of the symptomatic craniofacial titanium hardware and experienced rapid resolution of their painful parasthesias. Symptomatic plates were found in the region of the frontozygomatic suture or MacCarty keyhole, or in close proximity with the supraorbital nerve. Titanium plates, though relatively safe and low profile, can cause local nerve irritation or neuropathy. Surgeons should be cognizant of the potential complications of titanium craniofacial hardware and locations that are at higher risk for becoming symptomatic necessitating a second surgery for removal.

Shock timing measurements in DT ice layers

Science.gov (United States)

Robey, H. F.; Celliers, P. M.; Moody, J. D.; Sater, J.; Parham, T.; Kozioziemski, B.; Dylla-Spears, R. J.; Ross, J. S.; Lepape, S.; Ralph, J. E.; Berzak Hopkins, L. F.; Kroll, J. J.; Yoxall, B. E.; Hamza, A. V.; Boehly, T. R.; Nikroo, A.; Landen, O. L.; Edwards, M. J.

2013-10-01

Shock timing experiments on the National Ignition Facility (NIF) are routinely conducted using the keyhole target geometry, in which the strength and timing of multiple shocks are measured in a liquid-deuterium (D2) filled capsule interior. These targets have recently been modified to improve the surrogacy to ignition implosions by replacing the standard, continuous liquid D2 capsule fill with a deuterium-tritium (DT) ice layer with a central DT gas fill. These experiments remove any possible material surrogacy difference between D2 and DT as well as incorporating the physics of multiple shock release and recompression events from an ice layer of finite thickness, an effect that is absent in the liquid-filled targets. Experimental results and comparisons with numerical simulation are presented. Prepared by LLNL under Contract DE-AC52-07NA27344.

CO2 and diode laser welding of AZ31 magnesium alloy

International Nuclear Information System (INIS)

Zhu Jinhong; Li Lin; Liu Zhu

2005-01-01

Magnesium alloys are being increasingly used in automotive and aerospace structures. Laser welding is an important joining method in such applications. There are several kinds of industrial lasers available at present, including the conventional CO 2 and Nd:YAG lasers as well as recently available high power diode lasers. A 1.5 kW diode laser and a 2 kW CO 2 laser are used in the present study for the welding of AZ31 alloys. It is found that different welding modes exist, i.e., keyhole welding with the CO 2 laser and conduction welding with both the CO 2 and the diode lasers. This paper characterizes welds in both welding modes. The effect of beam spot size on the weld quality is analyzed. The laser processing parameters are optimized to obtain welds with minimum defects

What you see is what you buy

DEFF Research Database (Denmark)

Orquin, Jacob Lund; Mueller Loose, Simone; Scholderer, Joachim

the findings from two eye-tracking studies on consumer attention and product choice, a choice experiment manipulating saliency, size and clutter of packaging elements and a quasi-experimental study using natural product variations. The study revealed that increases in the saliency and surface size of packaging......Previous research has shown that increases in the overall saliency of products packages lead to increases in attention and how attention affects choice. However, no studies have addressed this issue at the level of individual packaging elements such as product claims and labels. The paper reports...... elements are associated with greater fixation likelihood and that attention to elements such as product claims and organic labels is associated with increased choice probability whereas attention to nutrition-related elements such as GDA labels or the Nordic keyhole label is associated with decreased...

A new approach in nuclear risk theory

International Nuclear Information System (INIS)

Serbanescu, D.

1994-01-01

The basic problem of the probabilistic safety assessment (PSA) is the errors evaluation. The main contributor to the final PSA results is the systematical error induced by the method itself. There may be some alternatives to the PSA classical approaches. All the new more successful approaches in the PSA results validation are related to the modelling problem. A comparison between two possible approaches for a pressurized heavy water reactor (PHWR) leakage event tree is included: The new approach proposed in (Serbanescu, 1991); the approach used in (Serbanescu, 1992), based on some unexplored yet features of the existing PSA analyses. The results are presented in relative units and an algorithm which was already implemented on an IBM.PC computer (Serbanescu, 1991) is used as a tool to decisions making tool. The decision making process should be based on a nuclear power plant (NPP) between modelling from the risk analysis point of view. This is the main feature of the proposed approach. (author). 4 refs, 2 figs, 2 tabs

Statistical inference an integrated Bayesianlikelihood approach

CERN Document Server

Aitkin, Murray

2010-01-01

Filling a gap in current Bayesian theory, Statistical Inference: An Integrated Bayesian/Likelihood Approach presents a unified Bayesian treatment of parameter inference and model comparisons that can be used with simple diffuse prior specifications. This novel approach provides new solutions to difficult model comparison problems and offers direct Bayesian counterparts of frequentist t-tests and other standard statistical methods for hypothesis testing.After an overview of the competing theories of statistical inference, the book introduces the Bayes/likelihood approach used throughout. It pre

Methodological approaches in the research of organizational culture

Directory of Open Access Journals (Sweden)

Janićijević Nebojša

2011-01-01

Full Text Available In the thirty-years-long research of organizational culture, two mutually opposed methodological approaches have emerged: objectivistic quantitative and subjectivistic-qualitative. These two approaches are based on opposite ontological and epistemological assumptions: they include different types of research, and use opposite, quantitative vs. qualitative, methods of research. Each of the methodological approaches has its advantages and disadvantages. For this reason a hybrid approach emerges as a legitimate choice in organizational culture research methodology. It combines elements of both subjectivistic and objectivistic methodological approaches, according to the goals, content, and context of the research and preferences of the researcher himself/herself. Since it is possible to combine the two principal methodological approaches in various ways, there are several possible hybrid methodologies in organizational culture research. After the review of objectivistic quantitative and subjectivistic-qualitative methodological approaches, one of possible hybrid approaches in the research of organizational culture is presented in this paper.

ANALYSING PRODUCTION DESIGN: POSITIONS AND APPROACHES

DEFF Research Database (Denmark)

Ion Wille, Jakob

2017-01-01

This article discusses the challenges of understanding production design and reviews dominant approaches to production design analysis.......This article discusses the challenges of understanding production design and reviews dominant approaches to production design analysis....

Posture as index for approach-avoidance behavior.

Directory of Open Access Journals (Sweden)

Anita Eerland

Full Text Available Approach and avoidance are two behavioral responses that make people tend to approach positive and avoid negative situations. This study examines whether postural behavior is influenced by the affective state of pictures. While standing on the Wii™ Balance Board, participants viewed pleasant, neutral, and unpleasant pictures (passively viewing phase. Then they had to move their body to the left or the right (lateral movement phase to make the next picture appear. We recorded movements in the anterior-posterior direction to examine approach and avoidant behavior. During passively viewing, people approached pleasant pictures. They avoided unpleasant ones while they made a lateral movement. These findings provide support for the idea that we tend to approach positive and avoid negative situations.

[Modern treatment approaches to gambling].

Science.gov (United States)

Egorov, A Iu

2014-01-01

Compulsive gambling has received widespread attention in the last decade. Gambling has become the first non-chemical addiction, which went down to the section "Addiction and related disorders" of the modern DSM-V. The review considers non-pharmacological and pharmacological approaches to the treatment of gambling. Among non-drug approaches, cognitive-behavioral therapy and 12-step programs have gained the most popularity in the "Gamblers Anonymous" community. Among pharmacological approaches, three classes of drugs: antidepressants (mainly SSRIs), opiate antagonists (naltrexone and nalmefene) and mood stabilizers (valproate, lithium, topiramate) proved to be effective in treatment of gambling. No differences in the efficacy of the three classes of psychotropic drugs have been identified. Preliminary results for N-acetylcysteine and memantine cause optimism in terms of perspective.

Thermodynamic approach to biomass gasification

International Nuclear Information System (INIS)

Boissonnet, G.; Seiler, J.M.

2003-01-01

The document presents an approach of biomass transformation in presence of steam, hydrogen or oxygen. Calculation results based on thermodynamic equilibrium are discussed. The objective of gasification techniques is to increase the gas content in CO and H 2 . The maximum content in these gases is obtained when thermodynamic equilibrium is approached. Any optimisation action of a process. will, thus, tend to approach thermodynamic equilibrium conditions. On the other hand, such calculations can be used to determine the conditions which lead to an increase in the production of CO and H 2 . An objective is also to determine transformation enthalpies that are an important input for process calculations. Various existing processes are assessed, and associated thermodynamic limitations are evidenced. (author)

A Theoretical Approach

African Journals Online (AJOL)

NICO

L-rhamnose and L-fucose: A Theoretical Approach ... L-ramnose and L-fucose, by means of the Monte Carlo conformational search method. The energy of the conformers ..... which indicates an increased probability for the occurrence of.

a Capability approach

African Journals Online (AJOL)

efforts towards gender equality in education as a means of achieving social justice. ... should mean that a lot of capability approach-oriented commentators are ... processes, their forms of exercising power, and their rules, unwritten cultures, ...

Enhancing Competency in English: The Covert Approach a Complementary to the Overt Approach in Teaching Grammar

Directory of Open Access Journals (Sweden)

Hussein Islam Abdullah

2015-01-01

Full Text Available Over the years, there has been a decline in the competency of the English Language in Malaysian schools. Many parties among them the Ministry of Education, relevant NGOs, academicians and people have expressed concern over the matter. The Education Ministry through its transformational policy has taken several measures to overcome the matter. It is employing appropriate strategies to solve the problems. The focus is on learning and teaching strategies as well as the content of the language. There is no doubt that grammar is a very important component in acquiring the language in primary and secondary schools. The English teachers mostly use the communicative approach in teaching grammar. This is in line with the KBSR syllabus in mid 1980s which emphasized on the communicative method. Teachers’ training and materials such as textbooks cater for the covert method. However, some tend to ignore the structural approach which is equally effective and meaningful to increase the level of the students’ proficiency which was popular in the 1960s. The paper discusses on the two different approaches used – the covert and overt approaches – their strengths as well as weaknesses. Application of both approaches is also taken into consideration giving a better view of how grammar should be taught in schools.

Exploring Academics' Approaches to Managing Team Assessment

Science.gov (United States)

Augar, Naomi; Woodley, Carolyn J.; Whitefield, Despina; Winchester, Maxwell

2016-01-01

Purpose: The purpose of this paper is to develop an understanding of academics' approaches to managing team assessment at an Australian University with a view to informing policy development and assessment design. Design/methodology/approach: The research was conducted using a single exploratory case study approach focussing on the team assessment…

A Hybrid Approach to Teaching Managerial Economics

Science.gov (United States)

Metzgar, Matthew

2014-01-01

Many institutions in higher education are experimenting with hybrid teaching approaches to undergraduate courses. Online resources may provide a number of advantages to students as compared to in-class approaches. Research regarding the effectiveness of hybrid approaches is mixed and still accumulating. This paper discusses the use of a hybrid…

Surgery-first orthognathic approach vs traditional orthognathic approach: Oral health-related quality of life assessed with 2 questionnaires.

Science.gov (United States)

Pelo, Sandro; Gasparini, Giulio; Garagiola, Umberto; Cordaro, Massimo; Di Nardo, Francesco; Staderini, Edoardo; Patini, Romeo; de Angelis, Paolo; D'Amato, Giuseppe; Saponaro, Gianmarco; Moro, Alessandro

2017-08-01

The purposes of the study were to investigate and evaluate the differences detected by the patients between the traditional orthognathic approach and the surgery-first one in terms of level of satisfaction and quality of life. A total of 30 patients who underwent orthognathic surgery for correction of malocclusions were selected and included in this study. Fifteen patients were treated with the conventional orthognathic surgery approach, and 15 patients with the surgery-first approach. Variables were assessed through the Orthognathic Quality of Life Questionnaire and the Oral Health Impact Profile questionnaire and analyzed with 2-way repeated-measures analysis of variance. The results showed significant differences in terms of the Orthognathic Quality of Life Questionnaire (P surgery in the surgery-first group and an initial worsening during orthodontic treatment in the traditional approach group followed by postoperative improvement. This study showed that the worsening of the facial profile during the traditional orthognathic surgery approach decompensation phase has a negative impact on the perception of patients' quality of life. Surgeons should consider the possibility of a surgery-first approach to prevent this occurrence. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

A Contrastive Study of Two Approaches to Teach Grammar

Institute of Scientific and Technical Information of China (English)

Cai; Lin

2007-01-01

There are many kinds of methods of teaching grammar, no matter what they are, these approaches can generally be classified into two approaches-deductive and inductive. What an appropriate grammar teaching approach is by examining the inductive and deductive approaches to grammar teaching and learning. It starts with the definitions of inductive and deductive approaches to grammar teaching, followed by a contrastive study of these two approaches in terms of both the bases and the application. Finally, it explores the inductive approach and outlines the benefits of this approach and suggests an alternative view of grammar teaching.

Cavernous malformations isolated from cranial nerves: Unexpected diagnosis?

Science.gov (United States)

Rotondo, Michele; Natale, Massimo; D'Avanzo, Raffaele; Pascale, Michela; Scuotto, Assunta

2014-11-01

Cranial nerves (CN) cavernous malformations (CMs) are lesions that are isolated from the CNs. The authors present three cases of CN CMs, for which MR was demonstrated to be critical for management, and surgical resection produced good outcomes for the patients. Surgical removal is the recommended course of action to restore or preserve neurological function and to eliminate the risk of future haemorrhage. However, the anatomical location and the complexity of nearby neural structures can make these lesions difficult to access and remove. In this study, the authors review the literature of reported cases of CN CMs to analyse the clinical and radiographic presentations, surgical approaches and neurological outcomes. A MEDLINE/Pub Med search was performed and revealed 86 cases of CN CMs. The authors report three additional cases in this study for a total of 89 cases. CMs affecting the optic nerve (CN II), oculomotor nerve (CN III), facial/vestibule-cochlear nerves (CN VII, CN VIII) have been described. The records of three patients were reviewed with respect to the lesion locations, symptoms, surgical approaches and therapeutic considerations. Clinical and radiological follow-up results are reported. Three patients (2 females, 1 male; age range 21-37 year) presented with three CN lesions. One lesion involved CN III, one lesion involved CN VII-CN VIII, and one involved CN II. The patient with the CN III lesion had a one-month history of mild right ptosis and diplopia. The patient with the CN VII-CN VIII lesion exhibited acute hearing loss and on the left and left facial paresis. The patient with the opticchiasmatic lesion presented with acute visual deterioration on the right and a left temporal field deficit in the left eye. Pterional and orbitozygomatic craniotomies were performed for the CN III lesion and the CN II lesion, and retrosigmoid craniotomy was performed for the cerebello-pontine angle lesion. All patients experienced symptom improvement after surgery. On

The enter-educate approach.

Science.gov (United States)

Piotrow, P T; Coleman, P L

1992-03-01

This article describes how the Population Communication Services (PCS) has seized on the "enter-educate" approach, the blending of popular entertainment with social messages, to change reproductive health behavior. The enter-educate approach spreads its message through songs, soap operas, variety shows, and other types of popular entertainment mediums. Because they entertain, enter-educate projects can capture the attention of an audience -- such as young people -- who would otherwise scorn social messages. And the use of population mediums makes it possible to reach a variety of audiences. Funded by USAID, PCS began its first enter-educate project in response to the increasing number of teenage pregnancies in Latin America. PCS developed 2 songs and videos, which featured popular teenage singers to serve as role models, to urge abstinence. The songs became instant hits. Since then, PCS has mounted more then 80 major projects in some 40 countries. Highlights of programs range from a successful multi-media family planning campaign in Turkey to humorous television ads in Brazil promoting vasectomy. Recently, PCS initiated projects to teach AIDS awareness. At the core of the enter-educate approach is the social learning theory which holds that much behavior is learned through the observation of role-models. Health professionals work alongside entertainers to produce works that have audience appeal and factual social messages. The enter-educate approach works because it is popular, pervasive, personal, persuasive, and profitable. PCS has found that enter-educate programs pay for themselves through cost sharing and cost recovery.

Cranio-orbital approach for complex aneurysmal surgery.

LENUS (Irish Health Repository)

Kelleher, M O

2012-02-03

Certain aneurysms of the anterior circulation continue to offer a technical challenge for safe exposure and clipping. The purpose of this paper was to describe the cranio-orbital approach for surgical clipping of complex aneurysms and to evaluate prospectively the associated complications of this approach. Prospective audit of all patients undergoing cranio-orbital approach for aneurysm surgery from 1997 to 2004 by the senior author. Twenty-five patients, eight male and 17 female, median age of 52 years, range 28-73. All patients had a standard pterional approach supplemented by an orbital osteotomy. In the 7-year period 367 patients underwent treatment for their aneurysms (169 clipped and 198 coiled). Of the 169 patients who were operated on, 29 had a skull base approach, of which 25 were cranio-orbital. The aneurysm location was as follows: 16 middle cerebral artery (MCA), three carotid bifurcation, four anterior communicating artery (ACOMM), one ophthalmic and one basilar. There were no approach-related complications. The cranio-orbital craniotomy can be a useful adjunct in the surgical treatment of giant or complex aneurysms. It offers the following advantages over a standard pterional approach: reduces operative distance; allows easy splitting of the sylvian fissure; and provides a wide arc of exposure with multiple working corridors.

Pilot Task Demand Load During RNAV Approaches

NARCIS (Netherlands)

Heiligers, M.M.

2011-01-01

The question that started this research was: “Why is approach A more difficult to fly for a pilot than approach B?”. To find an answer to this question, pilots flew a large variety of Area Navigation (RNAV) approaches during several flight simulator and real flight experiments. The results of these

Low current approach to ignition

International Nuclear Information System (INIS)

Cenacchi, G.; Sugiyama, L.; Airoldi, A.; Coppi, B.

1996-01-01

The open-quotes standardclose quotes path to achieve ignition conditions so far has been that of producing plasmas with the maximum current and poloidal field that axe compatible with the applied toroidal field and the geometry of the adopted configuration (the low q a approach.) The other approach is that motivated by recent experiments with reversed shear configurations, with relatively low currents and high fields corresponding to high values of q a (e-g., q a ≅ 6). While the first approach can be pursued with ohmic heating alone, the second one necessarily involves an auxiliary heating system. One of the advantages of this approach is that the onset of large scale internal modes can be avoided as q(ψ) is kept above 1 over the entire plasma column. Since quite peaked density profiles are produced in the regimes where enhanced confinement is observed, the α-particle power levels for which ignition can be reached and therefore the thermal wall loading on the first wall, can be reduced relatively to the standard, low q a , approach. The possibility is considered that ignition is reached in the reversed shear, high q a , regime and that this is followed by a transition to non-reversed profiles, or even the low q a regime, assuming that the excitation of modes involving magnetic reconnection will not undermine the needed degree of confinement. These results have been demonstrated by numerical transport simulation for the Ignitor-Ult machine, but are applicable to all high field ignition experiments

Primal and dual approaches to fishing capacity

DEFF Research Database (Denmark)

Kerstens, Kristiaan; Vestergaard, Niels

2013-01-01

Application of primal non-parametric approaches to estimation of fishing capacity provides useful disaggregated information about fishing firm’s capacities utilizations. A potentially serious issue is that the estimated capacity utilization rates can be relatively low. This may call for reductions...... in the fishing fleet that are political impossible to defend. In this paper two modifications of the traditional approach are explored. First, non-convex technologies are introduced and it is shown how the primal non-parametric approach leads to different capacity utilization rates. Then capacity utilization...... measures using cost functions are specified for both convex and non-convex technologies. It is illustrated how the convexity assumption impacts capacity utilization rates and how this dual approach differs from the primal approach. Second, the effect of utilizing these different convex versus non...

Approaches to risk assessment in food allergy

DEFF Research Database (Denmark)

Madsen, Charlotte Bernhard; Hattersley, S.; Buck, J.

2009-01-01

modelling is considered to be the most promising approach for use in population risk assessment (which is a particular focus for risk managers). For all approaches, further improvement of input data is desirable, particularly data on consumption patterns/food choices in food allergic consumers, data...... models. The workshop concluded that all the three approaches to safety and risk assessment of allergenic foods should continue to be considered. A particular strength of the MoE and probabilistic approaches is that they do not rely on low-dose extrapolations with its inherent issues. Probabilistic......A workshop was organised to investigate whether risk assessment strategies and methodologies used in classical/conventional toxicology may be used for risk assessment of allergenic foods. to discuss the advantages and limitations of different approaches and to determine the research needed to move...

Microscopic approach to nuclear anharmonicities

International Nuclear Information System (INIS)

Matsuo, Masayuki; Shimizu, Yoshifumi; Matsuyanagi, Kenichi

1985-01-01

Present status of microscopic study of nuclear anharmonicity phenomena is reviewed from the viewpoint of the time-dependent Hartree-Bogoliubov approach. Both classical- and quantum-mechanical aspects of this approach are discussed. The Bohr-Mottelson-type collective Hamiltonian for anharmonic gamma vibrations is microscopically derived by means of the self-consistent-collective-coordinate method, and applied to the problem of two-phonon states of 168 Er. (orig.)

Bounding approaches to system identification

CERN Document Server

Norton, John; Piet-Lahanier, Hélène; Walter, Éric

1996-01-01

In response to the growing interest in bounding error approaches, the editors of this volume offer the first collection of papers to describe advances in techniques and applications of bounding of the parameters, or state variables, of uncertain dynamical systems. Contributors explore the application of the bounding approach as an alternative to the probabilistic analysis of such systems, relating its importance to robust control-system design.

Approach to uncertainty in risk analysis

Energy Technology Data Exchange (ETDEWEB)

Rish, W.R.

1988-08-01

In the Fall of 1985 EPA's Office of Radiation Programs (ORP) initiated a project to develop a formal approach to dealing with uncertainties encountered when estimating and evaluating risks to human health and the environment. Based on a literature review of modeling uncertainty, interviews with ORP technical and management staff, and input from experts on uncertainty analysis, a comprehensive approach was developed. This approach recognizes by design the constraints on budget, time, manpower, expertise, and availability of information often encountered in ''real world'' modeling. It is based on the observation that in practice risk modeling is usually done to support a decision process. As such, the approach focuses on how to frame a given risk modeling problem, how to use that framing to select an appropriate mixture of uncertainty analyses techniques, and how to integrate the techniques into an uncertainty assessment that effectively communicates important information and insight to decision-makers. The approach is presented in this report. Practical guidance on characterizing and analyzing uncertainties about model form and quantities and on effectively communicating uncertainty analysis results is included. Examples from actual applications are presented.

Approach to uncertainty in risk analysis

International Nuclear Information System (INIS)

Rish, W.R.

1988-08-01

In the Fall of 1985 EPA's Office of Radiation Programs (ORP) initiated a project to develop a formal approach to dealing with uncertainties encountered when estimating and evaluating risks to human health and the environment. Based on a literature review of modeling uncertainty, interviews with ORP technical and management staff, and input from experts on uncertainty analysis, a comprehensive approach was developed. This approach recognizes by design the constraints on budget, time, manpower, expertise, and availability of information often encountered in ''real world'' modeling. It is based on the observation that in practice risk modeling is usually done to support a decision process. As such, the approach focuses on how to frame a given risk modeling problem, how to use that framing to select an appropriate mixture of uncertainty analyses techniques, and how to integrate the techniques into an uncertainty assessment that effectively communicates important information and insight to decision-makers. The approach is presented in this report. Practical guidance on characterizing and analyzing uncertainties about model form and quantities and on effectively communicating uncertainty analysis results is included. Examples from actual applications are presented

Proposing New Heuristic Approaches for Preventive Maintenance Scheduling

Directory of Open Access Journals (Sweden)

majid Esmailian

2013-08-01

Full Text Available The purpose of preventive maintenance management is to perform a series of tasks that prevent or minimize production breakdowns and improve reliability of production facilities. An important objective of preventive maintenance management is to minimize downtime of production facilities. In order to accomplish this objective, personnel should efficiently allocate resources and determine an effective maintenance schedule. Gopalakrishnan (1997 developed a mathematical model and four heuristic approaches to solve the preventive maintenance scheduling problem of assigning skilled personnel to work with tasks that require a set of corresponding skills. However, there are several limitations in the prior work in this area of research. The craft combination problem has not been solved because the craft combination is assumed as given. The craft combination problem concerns the computation of all combinations of assigning multi skilled workers to accomplishment of a particular task. In fact, determining craft combinations is difficult because of the exponential number of craft combinations that are possible. This research provides a heuristic approach for determining the craft combination and four new heuristic approach solution for the preventive maintenance scheduling problem with multi skilled workforce constraints. In order to examine the new heuristic approach and to compare the new heuristic approach with heuristic approach of Gopalakrishnan (1997, 81 standard problems have been generated based on the criterion suggested by from Gopalakrishnan (1997. The average solution quality (SQ of the new heuristic approaches is 1.86% and in old heuristic approaches is 8.32%. The solution time of new heuristic approaches are shorter than old heuristic approaches. The solution time of new heuristic approaches is 0.78 second and old heuristic approaches is 6.43 second, but the solution time of mathematical model provided by Gopalakrishnan (1997 is 152 second. �

Neural substrates of approach-avoidance conflict decision-making

Science.gov (United States)

Aupperle, Robin L.; Melrose, Andrew J.; Francisco, Alex; Paulus, Martin P.; Stein, Murray B.

2014-01-01

Animal approach-avoidance conflict paradigms have been used extensively to operationalize anxiety, quantify the effects of anxiolytic agents, and probe the neural basis of fear and anxiety. Results from human neuroimaging studies support that a frontal-striatal-amygdala neural circuitry is important for approach-avoidance learning. However, the neural basis of decision-making is much less clear in this context. Thus, we combined a recently developed human approach-avoidance paradigm with functional magnetic resonance imaging (fMRI) to identify neural substrates underlying approach-avoidance conflict decision-making. Fifteen healthy adults completed the approach-avoidance conflict (AAC) paradigm during fMRI. Analyses of variance were used to compare conflict to non-conflict (avoid-threat and approach-reward) conditions and to compare level of reward points offered during the decision phase. Trial-by-trial amplitude modulation analyses were used to delineate brain areas underlying decision-making in the context of approach/avoidance behavior. Conflict trials as compared to the non-conflict trials elicited greater activation within bilateral anterior cingulate cortex (ACC), anterior insula, and caudate, as well as right dorsolateral prefrontal cortex. Right caudate and lateral PFC activation was modulated by level of reward offered. Individuals who showed greater caudate activation exhibited less approach behavior. On a trial-by-trial basis, greater right lateral PFC activation related to less approach behavior. Taken together, results suggest that the degree of activation within prefrontal-striatal-insula circuitry determines the degree of approach versus avoidance decision-making. Moreover, the degree of caudate and lateral PFC activation is related to individual differences in approach-avoidance decision-making. Therefore, the AAC paradigm is ideally suited to probe anxiety-related processing differences during approach-avoidance decision-making. PMID:25224633

EMR implementation: big bang or a phased approach?

Science.gov (United States)

Owens, Kathleen

2008-01-01

There are two major strategies to implementing an EMR: the big-bang approach and the phased, or incremental, approach. Each strategy has pros and cons that must be considered. This article discusses these approaches and the risks and benefits of each as well as some training strategies that can be used with either approach.

Classroom EFL Writing: The Alignment-Oriented Approach

Science.gov (United States)

Haiyan, Miao; Rilong, Liu

2016-01-01

This paper outlines the alignment-oriented approach in classroom EFL writing. Based on a review of the characteristics of the written language and comparison between the product-focused approach and the process-focused approach, the paper proposes a practical classroom procedure as to how to teach EFL writing. A follow-up empirical study is…

[Surgical approaches to tibial plateau fractures].

Science.gov (United States)

Krause, Matthias; Müller, Gunnar; Frosch, Karl-Heinz

2018-06-06

Intra-articular tibial plateau fractures can present a surgical challenge due to complex injury patterns and compromised soft tissue. The treatment goal is to spare the soft tissue and an anatomical reconstruction of the tibial articular surface. Depending on the course of the fracture, a fracture-specific access strategy is recommended to provide correct positioning of the plate osteosynthesis. While the anterolateral approach is used in the majority of lateral tibial plateau fractures, only one third of the joint surface is visible; however, posterolateral fragments require an individual approach, e. g. posterolateral or posteromedial. If necessary, osteotomy of the femoral epicondyles can improve joint access for reduction control. Injuries to the posterior columns should be anatomically reconstructed and biomechanically correctly addressed via posterior approaches. Bony posterior cruciate ligament tears can be refixed via a minimally invasive posteromedial approach.

A hybrid approach for global sensitivity analysis

International Nuclear Information System (INIS)

Chakraborty, Souvik; Chowdhury, Rajib

2017-01-01

Distribution based sensitivity analysis (DSA) computes sensitivity of the input random variables with respect to the change in distribution of output response. Although DSA is widely appreciated as the best tool for sensitivity analysis, the computational issue associated with this method prohibits its use for complex structures involving costly finite element analysis. For addressing this issue, this paper presents a method that couples polynomial correlated function expansion (PCFE) with DSA. PCFE is a fully equivalent operational model which integrates the concepts of analysis of variance decomposition, extended bases and homotopy algorithm. By integrating PCFE into DSA, it is possible to considerably alleviate the computational burden. Three examples are presented to demonstrate the performance of the proposed approach for sensitivity analysis. For all the problems, proposed approach yields excellent results with significantly reduced computational effort. The results obtained, to some extent, indicate that proposed approach can be utilized for sensitivity analysis of large scale structures. - Highlights: • A hybrid approach for global sensitivity analysis is proposed. • Proposed approach integrates PCFE within distribution based sensitivity analysis. • Proposed approach is highly efficient.

Limits of the endoscopic transnasal transtubercular approach.

Science.gov (United States)

Gellner, Verena; Tomazic, Peter V

2018-06-01

The endoscopic transnasal trans-sphenoidal transtubercular approach has become a standard alternative approach to neurosurgical transcranial routes for lesions of the anterior skull base in particular pathologies of the anterior tubercle, sphenoid plane, and midline lesions up to the interpeduncular cistern. For both the endoscopic and the transcranial approach indications must strictly be evaluated and tailored to the patients' morphology and condition. The purpose of this review was to evaluate the evidence in literature of the limitations of the endoscopic transtubercular approach. A PubMed/Medline search was conducted in January 2018 entering following keywords. Upon initial screening 7 papers were included in this review. There are several other papers describing the endoscopic transtubercular approach (ETTA). We tried to list the limitation factors according to the actual existing literature as cited. The main limiting factors are laterally extending lesions in relation to the optic canal and vascular encasement and/or unfavorable tumor tissue consistency. The ETTA is considered as a high level transnasal endoscopic extended skull base approach and requires excellent training, skills and experience.

Approaches and perioperative management in periacetabular osteotomy surgery

DEFF Research Database (Denmark)

Søballe, Kjeld; Troelsen, Anders

2012-01-01

.9 to 8.1 years) of 209 PAOs performed using this approach have shown Kaplan-Meier survivorship rates of 94.7% at 5 years and 88.6% at 8.1 years, with conversion to total hip arthroplasty as the end point. Perioperative management includes a patient education program, optimized pain treatment strategies...... (local infiltration analgesia), and a progressive mobilization and exercise program. The transsartorial approach coupled with a specific perioperative management program has proved successful for PAO surgery.......In the early days of periacetabular osteotomy (PAO), surgical approaches were characterized by extensive soft-tissue dissection. The Smith-Petersen approach (and iliofemoral modifications) and the ilioinguinal approach have traditionally been used for PAO. The optimal surgical approach for PAO...

Understanding microelectronics a top-down approach

CERN Document Server

Maloberti, Franco

2011-01-01

The microelectronics evolution has given rise to many modern benefits but has also changed design methods and attitudes to learning. Technology advancements shifted focus from simple circuits to complex systems with major attention to high-level descriptions. The design methods moved from a bottom-up to a top-down approach. For today's students, the most beneficial approach to learning is this top-down method that demonstrates a global view of electronics before going into specifics. Franco Maloberti uses this approach to explain the fundamentals of electronics, such as processing functions,

A hybrid approach for biobjective optimization

DEFF Research Database (Denmark)

Stidsen, Thomas Jacob Riis; Andersen, Kim Allan

2018-01-01

to singleobjective problems is that no standard multiobjective solvers exist and specialized algorithms need to be programmed from scratch.In this article we will present a hybrid approach, which operates both in decision space and in objective space. The approach enables massive efficient parallelization and can...... be used to a wide variety of biobjective Mixed Integer Programming models. We test the approach on the biobjective extension of the classic traveling salesman problem, on the standard datasets, and determine the full set of nondominated points. This has only been done once before (Florios and Mavrotas...

Design of Quiet Rotorcraft Approach Trajectories

Science.gov (United States)

Padula, Sharon L.; Burley, Casey L.; Boyd, D. Douglas, Jr.; Marcolini, Michael A.

2009-01-01

A optimization procedure for identifying quiet rotorcraft approach trajectories is proposed and demonstrated. The procedure employs a multi-objective genetic algorithm in order to reduce noise and create approach paths that will be acceptable to pilots and passengers. The concept is demonstrated by application to two different helicopters. The optimized paths are compared with one another and to a standard 6-deg approach path. The two demonstration cases validate the optimization procedure but highlight the need for improved noise prediction techniques and for additional rotorcraft acoustic data sets.

Radiotherapy problem under fuzzy theoretic approach

International Nuclear Information System (INIS)

Ammar, E.E.; Hussein, M.L.

2003-01-01

A fuzzy set theoretic approach is used for radiotherapy problem. The problem is faced with two goals: the first is to maximize the fraction of surviving normal cells and the second is to minimize the fraction of surviving tumor cells. The theory of fuzzy sets has been employed to formulate and solve the problem. A linguistic variable approach is used for treating the first goal. The solutions obtained by the modified approach are always efficient and best compromise. A sensitivity analysis of the solutions to the differential weights is given

A Systematic Approach to Marital Enrichment.

Science.gov (United States)

Dinkmeyer, Don; Carlson, Jon

1986-01-01

Presents a systematic approach to enriching marital relationships. The history and current status of marital enrichment is reviewed. An Adlerian approach to marital enrichment is described. Applications of the program in enrichment groups, marriage therapy and couple groups are included. (Author)

Assessing Acid-Base Status: Physiologic Versus Physicochemical Approach.

Science.gov (United States)

Adrogué, Horacio J; Madias, Nicolaos E

2016-11-01

The physiologic approach has long been used in assessing acid-base status. This approach considers acids as hydrogen ion donors and bases as hydrogen ion acceptors and the acid-base status of the organism as reflecting the interaction of net hydrogen ion balance with body buffers. In the physiologic approach, the carbonic acid/bicarbonate buffer pair is used for assessing acid-base status and blood pH is determined by carbonic acid (ie, Paco 2 ) and serum bicarbonate levels. More recently, the physicochemical approach was introduced, which has gained popularity, particularly among intensivists and anesthesiologists. This approach posits that the acid-base status of body fluids is determined by changes in the dissociation of water that are driven by the interplay of 3 independent variables: the sum of strong (fully dissociated) cation concentrations minus the sum of strong anion concentrations (strong ion difference); the total concentration of weak acids; and Paco 2 . These 3 independent variables mechanistically determine both hydrogen ion concentration and bicarbonate concentration of body fluids, which are considered as dependent variables. Our experience indicates that the average practitioner is familiar with only one of these approaches and knows very little, if any, about the other approach. In the present Acid-Base and Electrolyte Teaching Case, we attempt to bridge this knowledge gap by contrasting the physiologic and physicochemical approaches to assessing acid-base status. We first outline the essential features, advantages, and limitations of each of the 2 approaches and then apply each approach to the same patient presentation. We conclude with our view about the optimal approach. Copyright © 2016 National Kidney Foundation, Inc. All rights reserved.

Complex epidemiological approach to human mutagenesis

International Nuclear Information System (INIS)

Czeizel, A.

1980-01-01

The main characteristics of the epidemiological approach are summarised and the criteria discussed for the adoption of this approach for the detection of human mutagenesis. Mutation monitoring systems are described and results of epidemiological studies of higher risk populations are presented. (C.F.)

Service creation: a model-based approach

NARCIS (Netherlands)

Quartel, Dick; van Sinderen, Marten J.; Ferreira Pires, Luis

1999-01-01

This paper presents a model-based approach to support service creation. In this approach, services are assumed to be created from (available) software components. The creation process may involve multiple design steps in which the requested service is repeatedly decomposed into more detailed

eHealth development: a holistic approach

NARCIS (Netherlands)

Lentferink, Aniek

2016-01-01

This presentation was held during the course 'eHealth development a holistic approach' at the University of Twente. The presentation included information about the project Quantified Self at Work and specifically the approach of co-creation during eHealth design with important stakeholders.

Leaderless Covert Networks : A Quantitative Approach

NARCIS (Netherlands)

Husslage, B.G.M.; Lindelauf, R.; Hamers, H.J.M.

2012-01-01

Abstract: Lindelauf et al. (2009a) introduced a quantitative approach to investigate optimal structures of covert networks. This approach used an objective function which is based on the secrecy versus information trade-off these organizations face. Sageman (2008) hypothesized that covert networks

Nanotechnology based approaches in cancer therapeutics

International Nuclear Information System (INIS)

Biswas, Amit Kumer; Islam, Md Reazul; Choudhury, Zahid Sadek; Kadir, Mohammad Fahim; Mostafa, Asif

2014-01-01

The current decades are marked not by the development of new molecules for the cure of various diseases but rather the development of new delivery methods for optimum treatment outcome. Nanomedicine is perhaps playing the biggest role in this concern. Nanomedicine offers numerous advantages over conventional drug delivery approaches and is particularly the hot topic in anticancer research. Nanoparticles (NPs) have many unique criteria that enable them to be incorporated in anticancer therapy. This topical review aims to look at the properties and various forms of NPs and their use in anticancer treatment, recent development of the process of identifying new delivery approaches as well as progress in clinical trials with these newer approaches. Although the outcome of cancer therapy can be increased using nanomedicine there are still many disadvantages of using this approach. We aim to discuss all these issues in this review. (review)