Construction and test of a superconducting phase-transition thermometer for bolometric cryodetectors

International Nuclear Information System (INIS)

Meier, H.J.

1990-10-01

In the framework of a project for the study of bolometric cryodetectors for the detection of heavy ions a superconducting phase-transition thermometer for the detection of heavy ions was constructed and tested with α particles. The thermometer consists of a 10 nm thick aluminium film, which was evaporated on a sapphire absorber with a typical magnitude of 2.5x2.5 x 0.33 mm 3 . By the method of photolithography the aluminium film was structured in form of a meander. By this at the working point of the thermometer resistances of up to 60 kΩ resulted, so that the signal acquisition was possible with usual readout electronics. Several of these thermometers were constructed, characterized in their properties, and tested. For the study of the detector properties of the thermometers in characterization measurements the width of the phase transitions dT ≅ 2 mK, the temperature dependence of the resistance to dR/dT ≅ 10MΩ/K, the thermal conductivity of the thermal coupling to the cooling bath, and the heat capacity of the bolometers to C ≅ 2 nJ/K were determined.The best energy resolution, which was reached with one of the superconducting phase-transition thermometers, amounts to 50 keV for 5.5 MeV α particles, which corresponds to a relative resolution of 0,9%. By this in the order of magnitude the quality of semiconductor detectors was reached. The best temperature resolution amounts to about 1 μK. (orig./HSI) [de

Thermometers: Understand the Options

Science.gov (United States)

... the options Thermometers come in a variety of styles. Understand the different types of thermometers and how ... MA. Fever in infants and children: Pathophysiology and management. http://www.uptodate.com/home. Accessed July 23, ...

Investigations on perturbations of microwave dielectric resonator thermometer

International Nuclear Information System (INIS)

Yu, Lili; Zhang, Guangming; Fernicola, V; Lu, Jinchuan

2017-01-01

Investigations of antenna probe length, antenna-dielectric distance, cavity filling and humidity on microwave resonator thermometer with respect to Q , spurious mode depression, coupling strength, accuracy, shock resistance or sensitivity were carried out in order to improve the dielectric resonator thermometer performance. Significant improvement of Q and depression of spurious mode coupling were obtained when the antenna length was reduced. It also turns out that the Q and spurious mode coupling strength vary with the distance between dielectric and antenna pin, as well under appropriate antenna length. Filling the cavity with nitrogen increases coupling strength but decrease frequency-temperature sensitivity compared to a vacuum-pumped cavity. Besides, preliminary results on the microwave resonator sensitivity to air humidity were obtained. (technical note)

Fabrication of a mini multi-fixed-point cell for the calibration of industrial platinum resistance thermometers

Science.gov (United States)

Ragay-Enot, Monalisa; Lee, Young Hee; Kim, Yong-Gyoo

2017-07-01

A mini multi-fixed-point cell (length 118 mm, diameter 33 mm) containing three materials (In-Zn eutectic (mass fraction 3.8% Zn), Sn and Pb) in a single crucible was designed and fabricated for the easy and economical fixed-point calibration of industrial platinum resistance thermometers (IPRTs) for use in industrial temperature measurements. The melting and freezing behaviors of the metals were investigated and the phase transition temperatures were determined using a commercial dry-block calibrator. Results showed that the melting plateaus are generally easy to realize and are reproducible, flatter and of longer duration. On the other hand, the freezing process is generally difficult, especially for Sn, due to the high supercooling required to initiate freezing. The observed melting temperatures at optimum set conditions were 143.11 °C (In-Zn), 231.70 °C (Sn) and 327.15 °C (Pb) with expanded uncertainties (k  = 2) of 0.12 °C, 0.10 °C and 0.13 °C, respectively. This multi-fixed-point cell can be treated as a sole reference temperature-generating system. Based on the results, the realization of melting points of the mini multi-fixed-point cell can be recommended for the direct calibration of IPRTs in industrial applications without the need for a reference thermometer.

Ion thermometers - nuclear reactor applications

International Nuclear Information System (INIS)

Rosenkranz, J.; Jakes, D.

The principle is briefly described of ion thermometers and the effects are reported of radiation on the ion crystal properties. The results show that ion thermometers are applicable for in-core measurements. (J.P.)

Influence of Thermal Cycling on Cryogenic Thermometers

CERN Document Server

Balle, C; Rieubland, Jean Michel; Suraci, A; Togny, F; Vauthier, N

1999-01-01

The stringent requirements on temperature control of the superconducting magnets for the Large Hadron Collider (LHC), impose that the cryogenic temperature sensors meet compelling demands such as long-term stability, radiation hardness, readout accuracy better than 5 mK at 1.8 K and compatibility with industrial control equipment. This paper presents the results concerning long-term stability of resistance temperature sensors submitted to cryogenic thermal cycles. For this task a simple test facility has been designed, constructed and put into operation for cycling simultaneously 115 cryogenic thermometers between 300 K and 4.2 K. A thermal cycle is set to last 71/4 hours: 3 hours for either cooling down or warming up the sensors and 1 respectively 1/4 hour at steady temperature conditions at each end of the temperature cycle. A Programmable Logic Controller (PLC) drives automatically this operation by reading 2 thermometers and actuating on 3 valves and 1 heater. The first thermal cycle was accomplished in a...

21 CFR 880.2920 - Clinical mercury thermometer.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Clinical mercury thermometer. 880.2920 Section 880... Devices § 880.2920 Clinical mercury thermometer. (a) Identification. A clinical mercury thermometer is a... mercury. (b) Classification. Class II (special controls). The device is exempt from the premarket...

Calibration of Cryogenic Thermometers for the LHC

CERN Document Server

Balle, Ch; Vauthier, N; Thermeau, JP

2008-01-01

6000 cryogenic temperature sensors of resistive type covering the range from room temperature down to 1.6 K are installed on the LHC machine. In order to meet the stringent requirements on temperature control of the superconducting magnets, each single sensor needs to be calibrated individually. In the framework of a special contribution, IPN (Institut de Physique Nucléaire) in Orsay, France built and operated a calibration facility with a throughput of 80 thermometers per week. After reception from the manufacturer, the thermometer is first assembled onto a support specific to the measurement environment, and then thermally cycled ten times and calibrated at least once from 1.6 to 300 K. The procedure for each of these interventions includes various measurements and the acquired data is recorded in an ORACLE®-database. Furthermore random calibrations on some samples are executed at CERN to crosscheck the coherence between the approximation data obtained by both IPN and CERN. In the range of 1.5 K to 30 K...

A portable storage maximum thermometer

International Nuclear Information System (INIS)

Fayart, Gerard.

1976-01-01

A clinical thermometer storing the voltage corresponding to the maximum temperature in an analog memory is described. End of the measurement is shown by a lamp switch out. The measurement time is shortened by means of a low thermal inertia platinum probe. This portable thermometer is fitted with cell test and calibration system [fr

Cryogenic Thermometer Calibration Facility at CERN

CERN Document Server

Balle, C; Thermeau, J P

1998-01-01

A cryogenic thermometer calibration facility has been designed and is being commissioned in preparation for the very stringent requirements on the temperature control of the LHC superconducting magnets. The temperature is traceable in the 1.5 to 30 K range to standards maintained in a national metrological laboratory by using a set of Rhodium-Iron temperature sensors of metrological quality. The calibration facility is designed for calibrating simultaneously 60 industrial cryogenic thermometers in the 1.5 K to 300 K temperature range, a thermometer being a device that includes both a temperature sensor and the wires heat-intercept. The thermometers can be calibrated in good and degraded vacuum or immersed in the surrounding fluid and at different Joule self-heating conditions that match those imposed by signal conditioners used in large cryogenic machinery. The calibration facility can be operated in an automatic mode and all the control and safety routines are handled by a Programmable Logic Controller (PLC)...

Towards a practical Johnson noise thermometer for long-term measurements in harsh environments

International Nuclear Information System (INIS)

Greenen, Adam; Pearce, Jonathan; Cruickshank, David; Bramley, Paul

2015-01-01

The impact of mechanical and chemical changes in conventional sensors such as thermocouples and resistance thermometers can be avoided by instead using temperature sensors based on fundamental thermometry. A prime example of this is Johnson noise thermometry, which is based on measurement of the fluctuations in the voltage of a resistor arising from thermal motion of charge carriers - i.e. the 'Johnson noise'. A Johnson noise thermometer never needs calibration and is insensitive to the condition of the sensor material. It is therefore ideally suited to long-term temperature measurements in harsh environments, such as nuclear reactor coolant circuits, in-pile measurements, nuclear waste management and storage, and severe accident monitoring. There have been a number of previous attempts to develop a Johnson noise thermometer for the nuclear industry, but none have reached commercial exploitation because of technical problems in practical implementation. The main challenge is to extract the tiny Johnson noise signal from ambient electrical noise influences, both from the internal amplification electronics, and from external electrical noise sources. Recent advances in electronics technology and digital signal processing techniques have opened up new possibilities for developing a viable, practical Johnson noise thermometer. We describe a project funded by the UK Technology Strategy Board (now Innovate UK) 'Developing the nuclear supply chain' call, currently underway, to develop a practical Johnson noise thermometer that makes use of innovative electronics for ultralow noise amplification and signal processing. The new electronics technology has the potential to help overcome the problems encountered with previous attempts at constructing a practical Johnson noise thermometer. An outline of the new developments is presented, together with an overview of the current status of the project. (authors)

Towards a practical Johnson noise thermometer for long-term measurements in harsh environments

Energy Technology Data Exchange (ETDEWEB)

Greenen, Adam; Pearce, Jonathan [National Physical Laboratory, Hampton Road, Teddington, TW11 0LW, (United Kingdom); Cruickshank, David; Bramley, Paul [Metrosol Limited, Plum Park Estate, Watling Street, Paulerspury, Northamptonshire, NN12 6LQ, (United Kingdom)

2015-07-01

The impact of mechanical and chemical changes in conventional sensors such as thermocouples and resistance thermometers can be avoided by instead using temperature sensors based on fundamental thermometry. A prime example of this is Johnson noise thermometry, which is based on measurement of the fluctuations in the voltage of a resistor arising from thermal motion of charge carriers - i.e. the 'Johnson noise'. A Johnson noise thermometer never needs calibration and is insensitive to the condition of the sensor material. It is therefore ideally suited to long-term temperature measurements in harsh environments, such as nuclear reactor coolant circuits, in-pile measurements, nuclear waste management and storage, and severe accident monitoring. There have been a number of previous attempts to develop a Johnson noise thermometer for the nuclear industry, but none have reached commercial exploitation because of technical problems in practical implementation. The main challenge is to extract the tiny Johnson noise signal from ambient electrical noise influences, both from the internal amplification electronics, and from external electrical noise sources. Recent advances in electronics technology and digital signal processing techniques have opened up new possibilities for developing a viable, practical Johnson noise thermometer. We describe a project funded by the UK Technology Strategy Board (now Innovate UK) 'Developing the nuclear supply chain' call, currently underway, to develop a practical Johnson noise thermometer that makes use of innovative electronics for ultralow noise amplification and signal processing. The new electronics technology has the potential to help overcome the problems encountered with previous attempts at constructing a practical Johnson noise thermometer. An outline of the new developments is presented, together with an overview of the current status of the project. (authors)

Design of a Toolbox of RNA Thermometers.

Science.gov (United States)

Sen, Shaunak; Apurva, Divyansh; Satija, Rohit; Siegal, Dan; Murray, Richard M

2017-08-18

Biomolecular temperature sensors can be used for efficient control of large-volume bioreactors, for spatiotemporal imaging and control of gene expression, and to engineer robustness to temperature in biomolecular circuit design. Although RNA-based sensors, called "thermometers", have been investigated in both natural and synthetic contexts, an important challenge is to design diverse responses to temperature differing in sensitivity and threshold. We address this issue by constructing a library of RNA thermometers based on thermodynamic computations and experimentally measuring their activities in cell-free biomolecular "breadboards". Using free energies of the minimum free energy structures as well as melt profile computations, we estimated that a diverse set of temperature responses were possible. We experimentally found a wide range of responses to temperature in the range 29-37 °C with fold-changes varying over 3-fold around the starting thermometer. The sensitivities of these responses ranged over 10-fold around the starting thermometer. We correlated these measurements with computational expectations, finding that although there was no strong correlation for the individual thermometers, overall trends of diversity, fold-changes, and sensitivities were similar. These results present a toolbox of RNA-based circuit elements with diverse temperature responses.

An inexpensive high-temperature optical fiber thermometer

International Nuclear Information System (INIS)

Moore, Travis J.; Jones, Matthew R.; Tree, Dale R.; Allred, David D.

2017-01-01

An optical fiber thermometer consists of an optical fiber whose tip is coated with a highly conductive, opaque material. When heated, this sensing tip becomes an isothermal cavity that emits like a blackbody. This emission is used to predict the sensing tip temperature. In this work, analytical and experimental research has been conducted to further advance the development of optical fiber thermometry. An inexpensive optical fiber thermometer is developed by applying a thin coating of a high-temperature cement onto the tip of a silica optical fiber. An FTIR spectrometer is used to detect the spectral radiance exiting the fiber. A rigorous mathematical model of the irradiation incident on the detection system is developed. The optical fiber thermometer is calibrated using a blackbody radiator and inverse methods are used to predict the sensing tip temperature when exposed to various heat sources. - Highlights: • An inexpensive coating for an optical fiber thermometer sensing tip is tested. • Inverse heat transfer methods are used to estimate the sensing tip temperature. • An FTIR spectrometer is used as the detector to test the optical fiber thermometer using various heat sources.

New blackbody standard for the evaluation and calibration of tympanic ear thermometers at the NPL, United Kingdom

Science.gov (United States)

McEvoy, Helen C.; Simpson, Robert; Machin, Graham

2004-04-01

The use of infrared tympanic thermometers for monitoring patient health is widespread. However, studies into the performance of these thermometers have questioned their accuracy and repeatability. To give users confidence in these devices, and to provide credibility in the measurements, it is necessary for them to be tested using an accredited, standard blackbody source, with a calibration traceable to the International Temperature Scale of 1990 (ITS-90). To address this need the National Physical Laboratory (NPL), UK, has recently set up a primary ear thermometer calibration (PET-C) source for the evaluation and calibration of tympanic (ear) thermometers over the range from 15 °C to 45 °C. The overall uncertainty of the PET-C source is estimated to be +/- 0.04 °C at k = 2. The PET-C source meets the requirements of the European Standard EN 12470-5: 2003 Clinical thermometers. It consists of a high emissivity blackbody cavity immersed in a bath of stirred liquid. The temperature of the blackbody is determined using an ITS-90 calibrated platinum resistance thermometer inserted close to the rear of the cavity. The temperature stability and uniformity of the PET-C source was evaluated and its performance validated. This paper provides a description of the PET-C along with the results of the validation measurements. To further confirm the performance of the PET-C source it was compared to the standard ear thermometer calibration sources of the National Metrology Institute of Japan (NMIJ), Japan and the Physikalisch-Technische Bundesanstalt (PTB), Germany. The results of this comparison will also be briefly discussed. The PET-C source extends the capability for testing ear thermometers offered by the NPL body temperature fixed-point source, described previously. An update on the progress with the commercialisation of the fixed-point source will be given.

Intraoperative body temperature control: esophageal thermometer versus infrared tympanic thermometer.

Science.gov (United States)

Poveda, Vanessa de Brito; Nascimento, Ariane de Souza

2016-01-01

To verify the correlation between temperature measurements performed using an infrared tympanic thermometer and an esophageal thermometer during the intraoperative period. A longitudinal study of repeated measures was performed including subjects aged 18 years or older undergoing elective oncologic surgery of the digestive system, with anesthesia duration of at least 1 hour. Temperature measurements were performed simultaneously by a calibrated esophageal thermometer and by a calibrated infrared tympanic thermometer, with laboratory reading precision of ±0.2ºC. The operating room temperature remained between 19 and 21ºC. The study included 51 patients, mostly men (51%), white (80.4%). All patients were kept warm by a forced-air heating system, for an average of 264.14 minutes (SD = 87.7). The two temperature measurements showed no different behavior over time (p = 0.2205), however, tympanic measurements were consistently 1.24°C lower (ptemperatura realizadas por meio de um termômetro timpânico por infravermelho e por um termômetro esofágico, durante o período intraoperatório. Realizou-se um estudo longitudinal, de medidas repetidas, incluindo sujeitos com idade igual ou superior a 18 anos, submetidos à cirurgia oncológica eletiva do sistema digestório, com duração da anestesia de, no mínimo, 1 hora. As medidas de temperatura eram realizadas, ao mesmo tempo, por meio de um termômetro esofágico calibrado e por termômetro timpânico por infravermelho calibrado, com precisão de leitura em laboratório de ±0,2ºC. A temperatura da sala operatória permaneceu entre 19 e 21ºC. Foram incluídos 51 pacientes, em sua maioria homens (51%), brancos (80,4%). Todos os pacientes foram aquecidos com o sistema de ar forçado aquecido, em média por 264,14 minutos (DP = 87,7). As duas medidas de temperatura não tiveram comportamento diferente ao longo do tempo (p = 0,2205), mas a medida timpânica foi consistentemente menor em 1,24°C (p temperaturas mais

A low-temperature (4-300K) constant volume gas thermometer

International Nuclear Information System (INIS)

Combarieu, A. de

1976-01-01

A constant volume gas thermometer was built to calibrate the various secondary thermometers used at low temperature. This gas thermometer is placed in a cryostat where any stable temperature between 4 and 300K may be obtained. The principle is outlined, then the gas thermometer and its auxiliary equipment are briefly described; the corrections to be applied to the results are given and a table shows the values obtained [fr

Evaluation of flow-induced vibration of thermometer well for JOYO

International Nuclear Information System (INIS)

Isozaki, Kazunori; Tomita, Naoki

1997-05-01

Sodium leak accident of MONJU was caused high cycles fatigue damage of thermometer well by flow-induced vibration. It was due to the symmetric vortex shedding which was occurred rear flow of thermometer well. So, Thermometer wells installed in primary and secondary heat transport systems of JOYO were evaluated of flow-induced vibration. Evaluation of flow-induced vibration of thermometer well was done checking of flow-induced vibration base on authorized design report for JOYO, evaluation of summary flow-induced vibration by natural frequency of thermometer well in sodium as cantilever models, and evaluation based on small velocity rule of ASME Code Section III Appendix N-1300. By this result, thermometer wells (12B piping of secondary cooling system) were not satisfied requirement to avoid flow-induced vibration by small velocity rule. Therefore, Detailed vibration characteristic analysis, water flow-induced vibration test, dumping test and evaluation of structural integrity were carried out. These results, vibration amplitude of well on the tip was 0.13 mm (vibration non-dimensional amplitude of 0.015) and peak stress of 2.9 kg/mm 2 is occurred. Thermometer wells (12B piping of secondary cooling system) which occurred peak stress by flow vibration was confirmed enough to satisfy 5.3 kg/mm 2 of design fatigue limit. (author)

Measurement of body temperature by use of auricular thermometers versus rectal thermometers in dogs with otitis externa.

Science.gov (United States)

González, A Michelle; Mann, F A; Preziosi, Diane E; Meadows, Richard L; Wagner-Mann, Colette C

2002-08-01

To compare measurements of body temperature obtained with auricular thermometers versus rectal thermometers in dogs with otitis externa. Prospective study. 100 client-owned dogs: 50 with and 50 without clinical evidence of otitis externa. Dogs were evaluated for the presence of otitis externa on the basis of clinical signs, otoscopic examination, and cytologic evaluation of ear exudate. Auricular and rectal temperatures were obtained simultaneously in all dogs prior to and following ear examination. There was a high correlation between auricular and rectal temperatures in dogs with otitis externa both prior to and after ear manipulation. Significant differences were not detected in temperature measurements among dogs with different degrees of otitis externa. Auricular temperature readings obtained by use of an auricular thermometer in dogs with otitis externa are accurate measurements of body temperature, compared with rectal temperature measurements. Temperature measurements are reliable before and after examination of the ear canal.

Final report on SIM.T-S2: Comparison of the calibration of 100 Ω platinum resistance thermometers

Science.gov (United States)

del Campo, D.; Chimenti Ruiz, V.; Méndez-Lango, E.; Córdova, L.; von Borries, E.; Sánchez, C. A.; Arévalo, A.; Aguilera, B.; Guillén, E.; Cabrera, C.; Quintana, L.

2013-01-01

An International Comparison on industrial platinum resistance thermometers (PRTs) among the National Metrology Institutes (NMIs) of Spain, Mexico and the Andean Countries (Bolivia, Colombia, Ecuador, Peru and Venezuela) began in 2004 and was successfully completed in 2005. Two PRTs were circulated (hand-carried) and compared from -40 °C up to 250 °C. The Centro Español de Metrología (Spanish NMI), CEM, was the pilot laboratory and the Centro Nacional de Metrología (Mexican NMI), CENAM, was the co-pilot laboratory. This report presents the results of this comparison and provides detailed information of the measurements performed by the participating laboratories. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by SIM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Controlling mercury spills in laboratories with a thermometer exchange program

Energy Technology Data Exchange (ETDEWEB)

McLouth, Lawrence D.

2002-03-25

This paper presents a case for replacing mercury thermometers with their organic-liquid-filled counterparts. A review of liquid-in glass-thermometers is given. In addition, a brief summary of mercury's health effects and exposure limits is presented. Spill cleanup methods and some lessons learned from our experience are offered as well. Finally, an overview of the mercury thermometer exchange program developed at Lawrence Berkeley National Laboratory is presented.

Galileo Chain Thermometer

Science.gov (United States)

Ucke, C.; Schlichting, H. J.

2017-01-01

This relatively rare thermometer has a rather unusual display: lower temperatures are located at the top of the scale, higher ones at the bottom. A sphere on a chain floats in a suitable liquid, sinking at high temperatures when the density of the liquid decreases and rising in the increased density at low temperatures. With reasonable effort and…

Silicon photonic thermometer operating on multiple polarizations

DEFF Research Database (Denmark)

Guan, Xiaowei; Wang, Xiaoyan; Frandsen, Lars Hagedorn

2016-01-01

A silicon photonics optical thermometer simultaneously operating on the multiple polarizations is designed and experimentally demonstrated. Measured sensitivities are 86pm/°C and 48pm/°C for the transverse-electric and transverse-magnetic polarizations, respectively.......A silicon photonics optical thermometer simultaneously operating on the multiple polarizations is designed and experimentally demonstrated. Measured sensitivities are 86pm/°C and 48pm/°C for the transverse-electric and transverse-magnetic polarizations, respectively....

The constitution of the heat density of a gamma thermometer

International Nuclear Information System (INIS)

Hantouche, C.

1984-01-01

This paper's aim is to present the nuclear transfer function of the signal of the γ thermometer used in a PWR reactor. The nuclear transfer function between the linear nuclear power and the γ thermometer heat density has been established. The corresponding computation code has been built up. The results concerning the environment behaviour of the γ thermometer, the heat density axial and radial repartitions, the control rods and the grids' influences are presented and discussed. (orig.)

Adiabatic surface thermometer for improved production braze quality

International Nuclear Information System (INIS)

Dittbenner, G.R.

1975-01-01

An adiabatic surface thermometer was developed to control automatically the critical temperature-time cycle of a production vacuum-brazing process. Investigations revealed that optimum braze-joint strength required precise control of the brazing temperature. Spot-welded thermocouples could not be used because the spot welds cause surface damage. This thermometer touches the surface and uses a differential thermocouple and heater to measure surface temperature without heat flow, thereby eliminating large errors caused by conduction losses common to conventional spring-loaded thermocouples. Temperatures in air or vacuum are measured to 800 0 C with errors less than 5 0 C. This thermometer has minimized the rejection of production parts, resulting in a cost saving to the U. S. Energy Research and Development Administration

A Non-Mercury Thermometer Alternative for Use in Older Melting Point Apparatuses

Science.gov (United States)

Ongley, Lois K.; Kern, Clayton S.; Woods, Barry W.

2008-01-01

The State of Maine seeks to eliminate most mercury use. This includes removing mercury thermometers from secondary schools and discouraging Hg use in other educational institutions. Alternatives to mercury thermometers in chemical laboratory work include non-mercury thermometers, temperature probes, and thermocouples. In organic chemistry mercury…

CCT-K2.1: NRC/VNIIFTRI bilateral comparison of capsule-type standard platinum resistance thermometers from 13.8 K to 273.16 K

Energy Technology Data Exchange (ETDEWEB)

Hill, K.D.; Steele, A.G. [National Research Council of Canada, Institute for National Measurement Standards, Ottawa, ON (Canada); Dedikov, Y.A.; Shkraba, V.T. [Institute for Physical-Technical and Radiotechnical Measurements (VNIIFTRI), Moscow (Russian Federation)

2005-04-01

The Consultative Committee for Thermometry Key Comparison 2 (CCT-K2) results were published two years ago (2002 Metrologia 39 551-71). NRC served as the pilot laboratory for CCT-K2 and remains able to provide a scale and measurement system suitable for performing bilateral comparisons linked to the original key comparison results. In March 2003, measurements of two VNIIFTRI 100 {omega} capsule-style platinum resistance thermometers (CSPRTs), S/N 356 and 476, were undertaken to relate their local calibration to the results from the CCT-K2 exercise. The NRC Leeds and Northrup (L and N) CSPRT S/N 1872174 provides the link to the CCT-K2 results. The three CSPRTs were compared at the eight defining cryogenic temperatures of the International Temperature Scale of 1990 (ITS-90) in the range from 13.8033 K to 273.16 K. The reader is referred to the full text of the CCT-K2 report for a detailed explanation of the methodology employed for the comparison. Only the details unique to the measurements reported here will be addressed in this article. The NRC/VNIIFTRI bilateral comparison of capsule-style platinum resistance thermometers over the range 13.8 K to 273.16 K has revealed calibrations at VNIIFTRI to be in agreement with the KCRV of CCT-K2 within the expanded uncertainty for all temperatures of the comparison with the exception of the triple point of hydrogen at 13.8033 K. One of the two CSPRTs supplied by VNIIFTRI was found to be discrepant as revealed by differences at the triple point of water and at the lowest temperatures of the comparison, and was therefore excluded from further analysis. The linkage to the CCT-K2 data supports the evaluation of the VNIIFTRI CMCs in Appendix C of the KCDB. (authors)

The reproducibility of some thermometric fixed points and the accuracy of temperature measurements using platinum resistance thermometers

Energy Technology Data Exchange (ETDEWEB)

Ancsin, J. [National Research Council of Canada, Ottawa, ON (Canada). Inst. for National Measurement Standards; Mendez-Lango, E. [Centro Nacional de Metrologia (CENAM), Div. Termometria, Queretaro (Mexico)

1999-07-01

The reproducibility of some thermometric fixed points and the accuracy of four platinum resistance thermometers (PRTs) were studied. It was found that the fixed points of aluminium (Al), zinc (Zn), tin (Sn), indium (In) and gallium (Ga) were realized reproducibly within {+-}0.17 mK; {+-}0.11 mK; {+-}0.10 mK; {+-}0.13 mK and {+-}0.12 mK, respectively. Because the actual impurities and their concentration in our samples (of 99.9999 % or 99.999 99 % purity) are unknown, the systematic uncertainly due to impurities cannot be estimated. However, any of the samples of Ga, In, Sn, Zn and Al is consistent with the rest within {+-}0.2 mK, using a cubic or quadratic deviation function, in the temperature range 0 deg C to 660 deg C. This indicates that the effect of impurities is negligible. Four PRTs were selected at random. They were calibrated repeatedly, first up to the Zn point and then up to the Al point. The resistance of each PRT drifted. From time to time, for each PRT, a seemingly well-established resistance drift suddenly and unpredictably changed to a different rate of drift. Occasionally, the resistance of the PRTs shifted. Such unpredictable changes obviously limit the accuracy of temperature measurements using PRTs no matter what the accuracy of their calibrations. In the case of our four PRTs, the uncertainty of temperature measurements near 660 deg C ranged from about {+-}1 mK to about {+-}2,5 mK even though they were all calibrated at all fixed points well within {+-}0.25 mK uncertainty. Possible explanations are offered for the apparently permanent drifts and the erratic shifts in the resistance of the PRTs. Some comments are made concerning the ambiguity of 'immersion tests' in general. The furnaces of the National Research Council of Canada used in this work are high-temperature adiabatic calorimeters. (authors)

Infrared Thermometer: an accurate tool for temperature measurement during renal surgery

Directory of Open Access Journals (Sweden)

Giovanni Scala Marchini

2013-07-01

Full Text Available Purpose To evaluate infrared thermometer (IRT accuracy compared to standard digital thermometer in measuring kidney temperature during arterial clamping with and without renal cooling. Materials and Methods 20 pigs weighting 20Kg underwent selective right renal arterial clamping, 10 with (Group 1 - Cold Ischemia with ice slush and 10 without renal cooling (Group 2 - Warm Ischemia. Arterial clamping was performed without venous clamping. Renal temperature was serially measured following clamping of the main renal artery with the IRT and a digital contact thermometer (DT: immediate after clamping (T0, after 2 (T2, 5 (T5 and 10 minutes (T10. Temperature values were expressed in mean, standard deviation and range for each thermometer. We used the T student test to compare means and considered p < 0.05 to be statistically significant. Results In Group 1, mean DT surface temperature decrease was 12.6 ± 4.1°C (5-19°C while deep DT temperature decrease was 15.8 ± 1.5°C (15-18°C. For the IRT, mean temperature decrease was 9.1 ± 3.8°C (3-14°C. There was no statistically significant difference between thermometers. In Group 2, surface temperature decrease for DT was 2.7 ± 1.8°C (0-4°C and mean deep temperature decrease was 0.5 ± 1.0°C (0-3°C. For IRT, mean temperature decrease was 3.1 ± 1.9°C (0-6°C. No statistically significant difference between thermometers was found at any time point. conclusions IRT proved to be an accurate non-invasive precise device for renal temperature monitoring during kidney surgery. External ice slush cooling confirmed to be fast and effective at cooling the pig model. IRT = Infrared thermometer DT = Digital contact thermometer D:S = Distance-to-spot ratio

Ion thermometers in reactor technology

International Nuclear Information System (INIS)

Yakesh, D.; Kott, J.; Strnad, M.

1980-01-01

The width of the temperature discontinuity and the thermometric stability of the sensors are constant up to very high flux values. The immediate influence of irradiation is reduced to a decrease in the hysteresis of the conduction curve at the phase transition. When the readings of the ion thermometers are compared with the reading of Chromel-Alumel thermocouples, it is observed that the temperature difference amounts to approximately 7/degree/C in the case of thermocouples placed at the sensor socket; the temperature difference decreases to 2/degree/C in the case of the thermocouple junction situated between the electrodes. The good results obtained in the testing of the ion thermometers in nuclear reactors lead to the conclusion that these temperature sensors are promising for checking thermocouples in the core of nuclear power stations

Characteristics of infrared thermometers manufactured in Japan and calibration methods for sky radiant emittance

International Nuclear Information System (INIS)

Wang, X.; Horiguchi, I.; Machimura, T.

1993-01-01

Infrared thermometers to measure surface temperature have been increasingly adopted in recent years. The characteristics of the IR thermometer, however, are not well known.IR thermometers manufactured in Japan systematically adjust for ambient radiation based on the internal temperature of the thermometer. If, therefore, there is a large difference between the internal temperature of the IR thermometer and the apparent temperature associated with the surrounding radiation, a large error will be induced into the measured surface temperature.The purpose of our research was to determine the characteristics and measurement errors of IR thermometers. Experiments were performed with regard to the following items: (1) Measurement errors related to the internal temperature of the IR thermometer. (2) Linearity of the output signal of the IR thermometer. (3) Response of the output signal to changes in the emissivity setting. (4) Effect of sky radiant emittance on the measured surface temperature. (5) Calibration method for the terrestrial surface.The following is a summary of the results: Measurement error is affected by the internal temperature of the IR thermometer. Measurement accuracy is improved with a controlled internal temperature of 20-30°C. The measurement error becomes larger at emissivity settings under 0.7.The measurement error outdoors was not proportional to the downward longwave radiation, but to the sky radiant temperature measured by the IR thermometer. Calibration for sky radiant emittance was improved by using the difference between sky radiant temperature and air temperature.When the surface temperature measured by the infrared thermometer is plotted against the surface temperature measured by thermocouple, the sky radiant emittance error is obtained from the Y intercept. Additionally, the difference between true temperature and output of the IR thermometer for a reference plate was compared to that obtained for vegetation, and the RMS obtained was

SQUID-based noise thermometer for sub-Millikelvin refrigerators

Energy Technology Data Exchange (ETDEWEB)

Schmidt, Marco; Beyer, Joern; Klemm, Monique [Physikalisch-Technische Bundesanstalt, Abbestrasse 2-12, 10587 Berlin (Germany); Alivaliollahi, Sassan; Barthelmess, Henry [Magnicon GmbH, Barkhausenweg 11, 22339 Hamburg (Germany)

2015-07-01

The magnetic field fluctuation thermometer (MFFT) is a high-accuracy SQUID-based noise thermometer suitable for sub-Kelvin thermometry. A highly sensitive low-Tc SQUID magnetometer detects inductively the magnetic field fluctuation above a metal surface. The fluctuations are generated by the thermal activated noise currents inside the metal body that is thermally anchored to the temperature stage to be measured. The spectral shape is independent of temperature as the electrical conductivity is constant and the geometry is fixed. The magnetic noise power spectral amplitudes at any frequencies are directly proportional to temperature. Hence, only one reference measurement at a known temperature is required for calibration. A complete MFFT thermometer system for the temperature range of ca. 4 K down to <10 mK is commercially available. We have now developed an integrated MFFT with an extended range of operation down to <1 mK. For this purpose the sensitivity of the SQUID sensor has been increased, the metal body geometry modified and the magnetic shielding of the MFFT module improved. These modifications make it possible to obtain a thermometer noise temperature of <10 μK. We discuss the rationale for our MFFT configuration and present numerical simulations and experimental results.

27 CFR 30.23 - Use of precision hydrometers and thermometers.

Science.gov (United States)

2010-04-01

... hydrometers and thermometers. 30.23 Section 30.23 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO... Use of precision hydrometers and thermometers. Care should be exercised to obtain accurate hydrometer... entire quantity. The hydrometers should be kept clean and free of any oily substance. Immediately before...

Bilateral Comparison of Mercury and Gallium Fixed-Point Cells Using Standard Platinum Resistance Thermometer

Science.gov (United States)

Bojkovski, J.; Veliki, T.; Zvizdić, D.; Drnovšek, J.

2011-08-01

The objective of project EURAMET 1127 (Bilateral comparison of triple point of mercury and melting point of gallium) in the field of thermometry is to compare realization of a triple point of mercury (-38.8344 °C) and melting point of gallium (29.7646 °C) between the Slovenian national laboratory MIRS/UL-FE/LMK and the Croatian national laboratory HMI/FSB-LPM using a long-stem 25 Ω standard platinum resistance thermometer (SPRT). MIRS/UL/FE-LMK participated in a number of intercomparisons on the level of EURAMET. On the other hand, the HMI/LPM-FSB laboratory recently acquired new fixed-point cells which had to be evaluated in the process of intercomparisons. A quartz-sheathed SPRT has been selected and calibrated at HMI/LPM-FSB at the triple point of mercury, the melting point of gallium, and the water triple point. A second set of measurements was made at MIRS/UL/FE-LMK. After its return, the SPRT was again recalibrated at HMI/LPM-FSB. In the comparison, the W value of the SPRT has been used. Results of the bilateral intercomparison confirmed that the new gallium cell of the HMI/LPM-FSB has a value that is within uncertainty limits of both laboratories that participated in the exercise, while the mercury cell experienced problems. After further research, a small leakage in the mercury fixed-point cell has been found.

Development of a superconducting transition edge thermometer for calorimetric detection of heavy ions

Energy Technology Data Exchange (ETDEWEB)

Meier, J; Boehmer, W; Egelhof, P; Henning, W; Kienlin, A v [Gesellschaft fuer Schwerionenforschung mbH, Darmstadt (Germany) Mainz Univ. (Germany). Inst. fuer Physik; Shepard, K W [Argonne National Lab., IL (United States)

1991-10-01

A low temperature bolometer for the calorimetric detection of heavy ions was constructed and tested. An aluminium thin-film microstrip, patterned in a meander-line structure by photolithographic techniques, serves as superconducting transition edge thermometer on a sapphire absorber. A transition width {delta}T of the thermometer of the order of some mK, and a resistance of up to R{sub c} = 60 k{Omega} at the working point (T{sub c} {approx equal} 1.5 K) is achieved. In tests with {alpha}-particles signals of typically 1 V pulseheight after the preamplifier and decaytimes around hundred {mu}s were observed. For 5.5 MeV {alpha}-particles the measured energy resolution is {Delta}E = 50 keV, corresponding to a temperature resolution of about 1 {mu}K. First measurements were performed with {sup 20}Ne ions (E = 116 MeV). The dependence of the pulseheight and the FWHM on the working point were investigated and qualitatively explained. The best energy resolution was {Delta}E = 2.6 MeV; most probably the present limitations are determined by the temperature stabilization. (orig.).

High speed infrared radiation thermometer, system, and method

Science.gov (United States)

Markham, James R.

2002-01-01

The high-speed radiation thermometer has an infrared measurement wavelength band that is matched to the infrared wavelength band of near-blackbody emittance of ceramic components and ceramic thermal barrier coatings used in turbine engines. It is comprised of a long wavelength infrared detector, a signal amplifier, an analog-to-digital converter, an optical system to collect radiation from the target, an optical filter, and an integral reference signal to maintain a calibrated response. A megahertz range electronic data acquisition system is connected to the radiation detector to operate on raw data obtained. Because the thermometer operates optimally at 8 to 12 .mu.m, where emittance is near-blackbody for ceramics, interferences to measurements performed in turbine engines are minimized. The method and apparatus are optimized to enable mapping of surface temperatures on fast moving ceramic elements, and the thermometer can provide microsecond response, with inherent self-diagnostic and calibration-correction features.

The gamma thermometer as a measuring instrument of the nuclear power of a LWR core

International Nuclear Information System (INIS)

Hantouche, C.

1984-07-01

After a presentation of the gamma thermometer and its environment, this thesis deals with the calibration of a gamma thermometer or determination of the thermal transfer ratio of the signal. Then, the acquisition systems for signals obtained from gamma thermometers installed in PWR nuclear power plants are presented. One deals also with the nuclear transfer function establishment and deconvolution. Then, one deals with the reconstruction of the axial power of an assembly provided with a gamma thermometer. Qualitative and quantitative studies of measurements obtained from this gamma thermometer are finally presented. 64 refs [fr

Thermo-Chromium: A Contactless Optical Molecular Thermometer.

Science.gov (United States)

Otto, Sven; Scholz, Norman; Behnke, Thomas; Resch-Genger, Ute; Heinze, Katja

2017-09-07

The unparalleled excited-state potential-energy landscape of the chromium(III)-based dye [1] 3+ ([Cr(ddpd) 2 ] 3+ ; ddpd=N,N'-dimethyl-N,N'-dipyridin-2-yl-pyridin-2,6-diamine) enables a strong dual emission in the near infrared region. The temperature dependence of this dual emission allows the use of [1] 3+ as an unprecedented molecular ratiometric thermometer in the 210-373 K temperature range in organic and in aqueous media. Incorporation of [1] 3+ in biocompatible nanocarriers, such as 100 nm-sized polystyrene nanoparticles and solutol micelles, provides nanodimensional thermometers operating under physiological conditions. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Thermal Conductivity and Liquid Crystal Thermometers.

Science.gov (United States)

Edge, R. D., Ed.

1993-01-01

Describes using stock liquid crystal postcards as inexpensive classroom thermometers. Also suggests using these postcards as a good visual temperature indicator for classroom demonstrations such as temperature gradients. One such activity is provided. (MVL)

Reliability of an infrared forehead skin thermometer for core temperature measurements

NARCIS (Netherlands)

Kistemaker, J.A.; Hartog, E.A. den; Daanen, H.A.M.

2006-01-01

The SensorTouch thermometer performs an infrared measurement of the skin temperature above the Superficial Temporal Artery (STA). This study evaluates the validity and the accuracy of the SensorTouch thermometer. Two experiments were performed in which the body temperature was measured with a rectal

High-Temperature Compatible Nickel Silicide Thermometer And Heater For Catalytic Chemical Microreactors

DEFF Research Database (Denmark)

Jensen, Søren; Quaade, U.J.; Hansen, Ole

2005-01-01

Integration of heaters and thermometers is important for agile and accurate control and measurement of the thermal reaction conditions in microfabricated chemical reactors (microreactors). This paper describes development and operation of nickel silicide heaters and temperature sensors...... for temperatures exceeding 700 °C. The heaters and thermometers are integrated with chemical microreactors for heterogeneous catalytic conversion of gasses, and thermally activated catalytic conversion of CO to CO2 in the reactors is demonstrated. The heaters and thermometers are shown to be compatible...

The Infrared Thermometer in School Science: Teaching Physics with Modern Technologies

Science.gov (United States)

Girwidz, Raimund; Ireson, Gren

2011-01-01

Infrared thermometers measure temperature from a distance, using the infrared radiation emitted by all objects. These so-called non-contact thermometers make a wide variety of temperature measurement and monitoring activities accessible to school-age students. Portable hand-held sensors also enable new or simplified investigations to be carried…

[Comparison of body temperatures in children measured using 3 different thermometers: tympanic, skin and digital axillary].

Science.gov (United States)

Padilla-Raygoza, Nicolás; Ruiz-Paloalto, M Laura; Díaz-Guerrero, Rosalina; Olvera-Villanueva, Georgina; Maldonado, Angélica; Raygoza-Mendoza, María Del Pilar

2014-01-01

To compare body temperature measurements using tympanic, skin and digital axillary thermometers. Hospitalized or outpatient children from the General Hospital Celaya, ISSSTE Hospital Clinic and General Hospital No. 4 IMSS, and the pediatric private service in Celaya, Guanajuato, from 1 day of life until 16 years old, were recruited over a one month period, after their parents signed the consent form. The order of each institution was selected by simple randomization. Body temperatures were measured in triplicate using tympanic, skin and digital axillary thermometers. The sample consisted of 554 children. The Pearson r between the tympanic and digital axillary thermometers was 0.57 to 0.65, with a positive linear relationship (P<.05); between the skin and the digital axillary thermometers, it was between 0.47 and 0.52 with a positive linearrelationship (P<.05). The intra-observer Kappa for the tympanic thermometer was 0.86, and for the inter-observer was 0.77; for the skin thermometer it was 0.82 and 0.67, respectively, and for the digital axillary thermometer it was 0.86 for intra-observer reliability and 0.78 for inter -observer reliability. Tympanic and axillary thermometers showed better precision in measuring the body temperature in children than skin thermometers. Copyright © 2013 Elsevier España, S.L. All rights reserved.

Ultrafast Paper Thermometers Based on a Green Sensing Ink.

Science.gov (United States)

Tao, Xinglei; Jia, Hanyu; He, Yonglin; Liao, Shenglong; Wang, Yapei

2017-03-24

With the use of an ionic liquid as the ultrathermosensitive fluid, a paper thermometer is successfully developed with intrinsic ability of ultrafast response and high stability upon temperature change. The fluidic nature allows the ionic liquid to be easily deposited on paper by pen writing or inkjet printing, affording great promise for large-scale fabrication of low-cost paper sensors. Owing to the advantages of nonvolatilization, excellent continuity and deformability, the thermosensitive ink trapped within the cellulose fibers of paper matrix has no leakage or evaporation at open states, ensuring the excellent stability and repeatability of thermal sensing against arbitrary bending and folding operation. By shortening the heat exchange distance between ionic liquid and samples, it takes only 8 s for the thermometer to reach an electrical equilibrium at a given temperature. Moreover, the paper thermometer can be applied to remotely monitor temperature change with the combination of a wireless communication technology.

Accuracy of the Danish version of the 'distress thermometer'

DEFF Research Database (Denmark)

Bidstrup, Pernille Envold; Mertz, Birgitte Goldschmidt; Dalton, Susanne Oksbjerg

2012-01-01

Objective: Short screening instruments have been suggested to improve the detection of psychological symptoms. We examined the accuracy of the Danish version of the 'Distress Thermometer'. Methods: Between October 2008 and October 2009, 426 women with newly diagnosed primary breast cancer who were...... operated at the Breast Surgery Clinic of the Rigshospitalet, Copenhagen, were eligible for this study. Of these, 357 participated (84%) and 333 completed a questionnaire. The distress thermometer was evaluated against the 'hospital anxiety and depression scale' (HADS). We also examined the women's wish...

THE DYNAMIC RESPONSE OF THERMOMETER-WELL ASSEMBLIES.

Science.gov (United States)

parameter models of the thermometric system were constructed and gave acceptable agreement with the experimental results. These models can be used to predict the dynamic behavior of any similar thermometer system. (Author)

Application of radio frequency based digital thermometer for real-time monitoring of dairy cattle rectal temperature

Directory of Open Access Journals (Sweden)

Tridib Debnath

2017-09-01

Full Text Available Aim: Dairy cattle health monitoring program becomes vital for detecting the febrile conditions to prevent the outbreak of the animal diseases as well as ensuring the fitness of the animals that are directly affecting the health of the consumers. The aim of this study was to validate real-time rectal temperature (RT data of radio frequency based digital (RFD thermometer with RT data of mercury bulb (MB thermometer in dairy cattle. Materials and Methods: Two experiments were conducted. In experiment I, six female Jersey crossbred cattle with a mean (±standard error of the mean body weight of 534.83±13.90 kg at the age of 12±0.52 years were used to record RT for 2 h on empty stomach and 2 h after feeding at 0, 30, 60, 90, and 120 min using a RFD thermometer as well as a MB thermometer. In experiment II, six female Jersey crossbred cattle were further used to record RT for 2 h before exercise and 2 h after exercise at 0, 30, 60, 90, and 120 min. Two-way repeated measures analysis of variance with post hoc comparisons by Bonferroni test was done. Results: Real-time RT data recorded by RFD thermometer as well as MB thermometer did not differ (p>0.05 before and after feeding/exercise. An increase (p<0.05 in RT after feeding/exercise in experimental crossbred cattle was recorded by both RFD thermometer and MB thermometer. Conclusion: The results obtained in the present study suggest that the body temperature recordings from RFD thermometer would be acceptable and thus RFD thermometer could work well for monitoring real-time RT in cattle.

Germanium thermometers in the temperature range .1000K to 4.20K

International Nuclear Information System (INIS)

Hsieh, S.Y.; Sanchez, D.H.

1974-01-01

The sensitivity characteristics of two germanium thermometers that proved to be convenient sensors in the temperature range from .100 0 K to 4.2 0 K, are described. Their resistances change from about 8 x 10 5 ohms at .100 0 K to about 100 ohms at 4.2 0 K. The calibration curves were fitted to natural spline functions of order 3 in the whole range of temperatures. These functions give less than half millidegree standard dispersion against 15 millidegree standard dispersion when usual polynomial interpolations are used. It is discussed what spline functions are, and compare the goodness of spline interpolation with polynomial methods [pt

The carbon dioxide thermometer and the cause of global warming

International Nuclear Information System (INIS)

Calder, Nigel

1999-01-01

Carbon dioxide in the air may be increasing because the world is warming. This possibility, which contradicts the hypothesis of an enhanced greenhouse warming driven by manmade emissions, is here pursued in two ways. First, increments in carbon dioxide are treated as readings of a natural thermometer that tracks global and hemispheric temperature deviations, as gauged by meteorologists' thermometers. Calibration of the carbon dioxide thermometer to conventional temperatures then leads to a history of carbon dioxide since 1856 that diverges from the ice-core record. Secondly, the increments of carbon dioxide can also be accounted for, without reference to temperature, by the combined effects of cosmic rays, El Nino and volcanoes. The most durable effect is due to cosmic rays. A solar wind history, used as a long-term proxy for the cosmic rays, gives a carbon dioxide history similar to that inferred from the global temperature deviations. (author)

Demonstrating the Temperature Dependence of Density via Construction of a Galilean Thermometer

Science.gov (United States)

Priest, Marie A.; Padgett, Lea W.; Padgett, Clifford W.

2011-01-01

A method for the construction of a Galilean thermometer out of common chemistry glassware is described. Students in a first-semester physical chemistry (thermodynamics) class can construct the Galilean thermometer as an investigation of the thermal expansivity of liquids and the temperature dependence of density. This is an excellent first…

Radiation Requirements and Testing of Cryogenic Thermometers for the Ilc

Science.gov (United States)

Barnett, T.; Filippov, Yu. P.; Filippova, E. Yu.; Mokhov, N. V.; Nakao, N.; Klebaner, A. L.; Korenev, S. A.; Theilacker, J. C.; Trenikhina, J.; Vaziri, K.

2008-03-01

Large quantity of cryogenic temperature sensors will be used for operation of the International Linear Collider (ILC). Most of them will be subject to high radiation doses during the accelerator lifetime. Understanding of particle energy spectra, accumulated radiation dose in thermometers and its impact on performance are vital in establishing technical specification of cryogenic thermometry for the ILC. Realistic MARS15 computer simulations were performed to understand the ILC radiation environment. Simulation results were used to establish radiation dose requirements for commercially available cryogenic thermometers. Two types of thermometers, Cernox® and TVO, were calibrated prior to irradiation using different technique. The sensors were subjected then to up to 200 kGy electron beam irradiation with kinetic energy of 5 MeV, a representative of the situation at the ILC operation. A post-irradiation behavior of the sensors was studied. The paper describes the MARS15 model, simulation results, cryogenic test set-up, irradiation tests, and cryogenic test results.

Radiation requirements and testing of cryogenic thermometers for the ILC

International Nuclear Information System (INIS)

Barnett, T.; Filippov, Yu.P.; Mokhov, N.V.; Nakao, N.; Klebaner, A.L.; Korenev, S.A.; Theilacker, J.C.; Trenikhina, J.; Vaziri, K.

2007-01-01

Large quantity of cryogenic temperature sensors will be used for operation of the International Linear Collider (ILC). Most of them will be subject to high radiation doses during the accelerator lifetime. Understanding of particle energy spectra, accumulated radiation dose in thermometers and its impact on performance are vital in establishing technical specification of cryogenic thermometry for the ILC. Realistic MARS15 computer simulations were performed to understand the ILC radiation environment. Simulation results were used to establish radiation dose requirements for commercially available cryogenic thermometers. Two types of thermometers, Cernox(reg s ign) and TVO, were calibrated prior to irradiation using different technique. The sensors were subjected then to up to 200 kGy electron beam irradiation with kinetic energy of 5 MeV, a representative of the situation at the ILC operation. A post-irradiation behavior of the sensors was studied. The paper describes the MARS15 model, simulation results, cryogenic test set-up, irradiation tests, and cryogenic test results

Low-temperature thermometry. Use of a gas thermometer as a calibration standard between 4 and 300 K

International Nuclear Information System (INIS)

Combarieu, A. de

1978-01-01

A constant volume gas thermometer was built to calibrate the various secondary thermometers used at low temperature. This gas thermometer is placed in a cryostat where any stable temperature between 4 and 300 K may be obtained. After some words about low temperature thermometry, the gas thermometer and its auxiliary equipment are described briefly; the corrections to be applied to the results are given and the article ends with a table showing the values obtained [fr

The gamma thermometer

International Nuclear Information System (INIS)

Beraud, G.; Hourtoulle, F.

1983-01-01

The search for a detecting element capable of permanently measuring localised nuclear output which would also be robust straightforward and reliable led EDF to begin development work on a new type of detector in 1976: the gamma thermometer (THG). After briefly summarising the history of the project this article goes on to describe the principle and structure of the equipment used in EDF's PWR reactors. As a result of the extensive test programme carried out it has been possible to qualify analytical and calibration methods together with the thermal and nuclear models. In conclusion, the development prospects and future of such a detecting device are outlined [fr

Process for constructing a gamma thermometer

International Nuclear Information System (INIS)

Barbet, M.J.P.; Cohen, B.S.; Robillard, M.

1982-01-01

A process is described for constructing a gamma thermometer having a substance absorbing the radiation and a set of thermocouples for measuring the local power in a fuel assembly of a nuclear reactor. A claim is particularly made for the preparation of the tube containing it and for its filling with an inert gas [fr

Some observations on the use of the triple points of deuterium and xenon in interpolation schemes for platinum resistance thermometers below 273 K

International Nuclear Information System (INIS)

Kemp, R.C.

1988-01-01

The use of the triple points of deuterium and xenon is investigated in some interpolation schemes for platinum resistance thermometers between 13.8 K and 273 K. The use of these triple points together is shown to lead to a large sensitivity to errors in the realization of the boiling point of water or the triple point of gallium and of the triple point of xenon for interpolated temperatures below 25 K. The behaviour of these interpolation schemes is presented as evidence that the large non-uniqueness observed in temperature scales between 84 K and 273 K is due in part to measurement errors at the boiling point of water. The use of the triple point of xenon and in interpolation scheme between 25 K and 273 K is shown to lead to a large sensitivity to calibration errors in the triple points of xenon and gallium between 25 K and 54 K. (orig.)

Accuracy of peripheral thermometers for estimating temperature: a systematic review and meta-analysis.

Science.gov (United States)

Niven, Daniel J; Gaudet, Jonathan E; Laupland, Kevin B; Mrklas, Kelly J; Roberts, Derek J; Stelfox, Henry Thomas

2015-11-17

Body temperature is commonly used to screen patients for infectious diseases, establish diagnoses, monitor therapy, and guide management decisions. To determine the accuracy of peripheral thermometers for estimating core body temperature in adults and children. MEDLINE, EMBASE, Cochrane Central Register of Controlled Trials, and CINAHL Plus from inception to July 2015. Prospective studies comparing the accuracy of peripheral (tympanic membrane, temporal artery, axillary, or oral) thermometers with central (pulmonary artery catheter, urinary bladder, esophageal, or rectal) thermometers. 2 reviewers extracted data on study characteristics, methods, and outcomes and assessed the quality of individual studies. 75 studies (8682 patients) were included. Most studies were at high or unclear risk of patient selection bias (74%) or index test bias (67%). Compared with central thermometers, peripheral thermometers had pooled 95% limits of agreement (random-effects meta-analysis) outside the predefined clinically acceptable range (± 0.5 °C), especially among patients with fever (-1.44 °C to 1.46 °C for adults; -1.49 °C to 0.43 °C for children) and hypothermia (-2.07 °C to 1.90 °C for adults; no data for children). For detection of fever (bivariate random-effects meta-analysis), sensitivity was low (64% [95% CI, 55% to 72%]; I2 = 95.7%; P temperature measurement techniques are limited. Pooled data are associated with interstudy heterogeneity that is not fully explained by stratified and metaregression analyses. Peripheral thermometers do not have clinically acceptable accuracy and should not be used when accurate measurement of body temperature will influence clinical decisions. None.

MEMS Tunneling Micro Thermometer Based onTip Deflection of Bimetallic Cantilever Beam

Directory of Open Access Journals (Sweden)

Samrand K. Nezhadian

2007-10-01

Full Text Available Micro-electro-mechanical (MEM technology promises to significantly reduce the size, weight and cost of a variety of sensor systems. In this article has been described a highly sensitive novel type of thermometer based on deflection of a “bimetallic” microbeam. The proposed thermometer converts the thermal changes of a cantilevered bimetallic beam of submillimeter size into an electrical signal through tunneling-current modulation. The governing thermo-mechanical equation of a bimetallic cantilever beam has been derived and solved analytically. The obtained results show that the proposed tunneling micro thermometer is very sensitive to temperature changes due to exponential increasing of tunneling current but because of small gap between metallic electrodes, measurable range of temperature changes is small.

Measurement time and statistics for a noise thermometer with a synthetic-noise reference

Science.gov (United States)

White, D. R.; Benz, S. P.; Labenski, J. R.; Nam, S. W.; Qu, J. F.; Rogalla, H.; Tew, W. L.

2008-08-01

This paper describes methods for reducing the statistical uncertainty in measurements made by noise thermometers using digital cross-correlators and, in particular, for thermometers using pseudo-random noise for the reference signal. First, a discrete-frequency expression for the correlation bandwidth for conventional noise thermometers is derived. It is shown how an alternative frequency-domain computation can be used to eliminate the spectral response of the correlator and increase the correlation bandwidth. The corresponding expressions for the uncertainty in the measurement of pseudo-random noise in the presence of uncorrelated thermal noise are then derived. The measurement uncertainty in this case is less than that for true thermal-noise measurements. For pseudo-random sources generating a frequency comb, an additional small reduction in uncertainty is possible, but at the cost of increasing the thermometer's sensitivity to non-linearity errors. A procedure is described for allocating integration times to further reduce the total uncertainty in temperature measurements. Finally, an important systematic error arising from the calculation of ratios of statistical variables is described.

Effect of on-chip filter on Coulomb blockade thermometer

International Nuclear Information System (INIS)

Roschier, L; Penttilä, J S; Gunnarsson, D; Prunnila, M; Meschke, M; Savin, A

2012-01-01

Coulomb Blockade Thermometer (CBT) is a primary thermometer based on electric conductance of normal tunnel junction arrays. One limitation for CBT use at the lowest temperatures has been due to environmental noise heating. To improve on this limitation, we have done measurements on CBT sensors fabricated with different on-chip filtering structures in a dilution refrigerator with a base temperature of 10 mK. The CBT sensors were produced with a wafer scale tunnel junction process. We present how the different on-chip filtering schemes affect the limiting saturation temperatures and show that CBT sensors with proper on-chip filtering work at temperatures below 20 mK and are tolerant to noisy environment.

27 CFR 30.22 - Hydrometers and thermometers.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Hydrometers and... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS GAUGING MANUAL Gauging Instruments § 30.22 Hydrometers and thermometers. The hydrometers used are graduated to read the proof of aqueous alcoholic solutions at 60 degrees...

KEY COMPARISON: CCT-K2.1: NRC/VNIIFTRI bilateral comparison of capsule-type standard platinum resistance thermometers from 13.8 K to 273.16 K

Science.gov (United States)

Hill, K. D.; Steele, A. G.; Dedikov, Y. A.; Shkraba, V. T.

2005-01-01

The Consultative Committee for Thermometry Key Comparison 2 (CCT-K2) results were published two years ago (2002 Metrologia 39 551-71). NRC served as the pilot laboratory for CCT-K2 and remains able to provide a scale and measurement system suitable for performing bilateral comparisons linked to the original key comparison results. In March 2003, measurements of two VNIIFTRI 100 Ω capsule-style platinum resistance thermometers (CSPRTs), S/N 356 and 476, were undertaken to relate their local calibration to the results from the CCT-K2 exercise. The NRC Leeds and Northrup (L&N) CSPRT S/N 1872174 provides the link to the CCT-K2 results. The three CSPRTs were compared at the eight defining cryogenic temperatures of the International Temperature Scale of 1990 (ITS-90) in the range from 13.8033 K to 273.16 K. The reader is referred to the full text of the CCT-K2 report for a detailed explanation of the methodology employed for the comparison. Only the details unique to the measurements reported here will be addressed in this article. The NRC/VNIIFTRI bilateral comparison of capsule-style platinum resistance thermometers over the range 13.8 K to 273.16 K has revealed calibrations at VNIIFTRI to be in agreement with the KCRV of CCT-K2 within the expanded uncertainty for all temperatures of the comparison with the exception of the triple point of hydrogen at 13.8033 K. One of the two CSPRTs supplied by VNIIFTRI was found to be discrepant as revealed by differences at the triple point of water and at the lowest temperatures of the comparison, and was therefore excluded from further analysis. The linkage to the CCT-K2 data supports the evaluation of the VNIIFTRI CMCs in Appendix C of the KCDB. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions

Cause elucidation of sodium leakage incident at `Monju` reactor. Vibration of thermometer due to fluid force

Energy Technology Data Exchange (ETDEWEB)

Iwata, Koji; Wada, Yusaku; Morishita, Masaki; Yamaguchi, Akira; Ichimiya, Masakazu [Power Reactor and Nuclear Fuel Development Corp., Oarai, Ibaraki (Japan). Oarai Engineering Center

1997-01-01

This is a report of summarized results of investigation and analysis on fracture of thermometer which is direct reason of sodium leakage incident at the second main cooling system of fast breeder reactor `Monju`. Various surveys such as on various damage factors, on flowing power vibrational features containing flowing power vibrational test of thermometer, on evaluation of high cycle fatigue due to flowing power vibration and details on propagation of and fracture due to fatigue crack, on why only said thermometer damaged, and so forth were executed. As results of these examinations, a decision was arrived that high cycle fatigue due to vibration formed by fluid force (fluid force vibration) was a direct cause of the thermometer damage. (G.K.)

Cryogenic thermometer calibration system using a helium cooling loop and a temperature controller [for LHC magnets

CERN Document Server

Chanzy, E; Thermeau, J P; Bühler, S; Joly, C; Casas-Cubillos, J; Balle, C

1998-01-01

The IPN-Orsay and CERN are designing in close collaboration a fully automated cryogenic thermometer calibration facility which will calibrate in 3 years 10,000 cryogenic thermometers required for the Large Hadron Collider (LHC) operation. A reduced-scale model of the calibration facility has been developed, which enables the calibration of ten thermometers by comparison with two rhodium-iron standard thermometers in the 1.8 K to 300 K temperature range under vacuum conditions. The particular design, based on a helium cooling loop and an electrical temperature controller, gives good dynamic performances. This paper describes the experimental set-up and the data acquisition system. Results of experimental runs are also presented along with the estimated global accuracy for the calibration. (3 refs).

Development and psychometric testing of a new tool for detecting moral distress: the Moral Distress Thermometer.

Science.gov (United States)

Wocial, Lucia D; Weaver, Michael T

2013-01-01

To report the development and psychometric testing of the Moral Distress Thermometer. The Moral Distress Thermometer is a new screening tool to measure moral distress in nurses who practise in the hospital setting. Moral distress occurs when one knows the ethically correct thing to do, but is prevented from acting on that perceived obligation. It is a well documented phenomenon with negative consequences that may be experienced by nurses. Creating an instrument to effectively and efficiently measure moral distress in a timely way has been identified as a priority for nursing. This study used a cross-sectional survey design. Data collection for this research occurred in 2009. Participants simultaneously completed either the adult or pediatric version of the Moral Distress Scale version 2009 and the Moral Distress Thermometer. A total of 529 participants from various clinical areas completed both tools. Coefficients alpha were adequate for both Adult (0·90) and Pediatric (0·92) Moral Distress Scale 2009 scales. Statistically significant Pearson correlations were found for the Moral Distress Thermometer with Adult Moral Distress Scale 2009 and Pediatric Moral Distress Scale 2009 and higher Moral Distress Thermometer, Adult Moral Distress Scale 2009 and Pediatric Moral Distress Scale 2009 means for participants who had left or who considered leaving a position because of moral distress. These findings provide support for the validity of the Moral Distress Thermometer. © 2012 Blackwell Publishing Ltd.

Low-energy X-ray detection in cryogenic detectors with tungsten thermometers

International Nuclear Information System (INIS)

Colling, P.; Nucciotti, A.; Bucci, C.; Cooper, S.; Ferger, P.; Frank, M.; Nagel, U.; Proebst, F.; Seidel, W.

1994-08-01

In the course of our development of calorimetric particle detectors with superconducting phase transition thermometers, we have succeeded in depositing epitaxial α-tungsten films on sapphire which have critical temperatures T c near 15 mK. To our knowledge this is the first time that the T c of bulk tungsten has been observed in thin films. Such films used as thermometers are very sensitive and provide good energy resolution: with 4 g and 32 g sapphire crystals energy resolutions of better than 100eV (FWHM) for 1.5 KeV X-rays have been achieved. (orig.)

Very high temperature ultrasonic thermometer

International Nuclear Information System (INIS)

Jorzik, E.

1983-01-01

An ultrasonic thermometer comprises an electric pulse transducer head, a pulse transmission line, a notched sensor wire attached to and extending along the axis of said transmission line and a sheath enclosing the transmission line and the sensor wire, a portion of the interior face of the sheath being covered by a stuffing material along at least the length of the notched part of the sensor wire, such that contact between the sensor wire and the stuffing material does not substantially give rise to reflection of an ultrasonic pulse at the point of contact. (author)

Measuring Total Column Water Vapor by Pointing an Infrared Thermometer at the Sky

Science.gov (United States)

Mims, Forrest M., III; Chambers, Lin H.; Brooks, David R.

2011-01-01

A 2-year study affirms that the temperature (Tz) indicated by an inexpensive ($20 to $60) IR thermometer pointed at the cloud-free zenith sky provides an approximate indication of the total column water vapor (precipitable water or PW). PW was measured by a MICROTOPS II sun photometer. The coefficient of correlation (r2) of the PW and Tz was 0.90, and the rms difference was 3.2 mm. A comparison of the Tz data with the PW provided by a GPS site 31 km NNE yielded an r2 of 0.79, and an rms difference of 5.8 mm. An expanded study compared Tz from eight IR thermometers with PW at various times during the day and night from 17 May to 18 October 2010, mainly at the Texas site and 10 days at Hawaii's Mauna Loa Observatory (MLO). The best results of this comparison were provided by two IR thermometers models that yielded an r2 of 0.96 and an rms difference with the PW of 2.7 mm. The results of both the ongoing 2-year study and the 5-month instrument comparison show that IR thermometers can measure PW with an accuracy (rms difference/mean PW) approaching 10%, the accuracy typically ascribed to sun photometers.

Model for cryogenic particle detectors with superconducting phase transition thermometers

International Nuclear Information System (INIS)

Proebst, F.; Frank, M.; Cooper, S.; Colling, P.; Dummer, D.; Ferger, P.; Nucciotti, A.; Seidel, W.; Stodolsky, L.

1994-09-01

We present data on a detector composed of an 18 g Si crystal and a superconducting phase transition thermometer which could be operated over a wide temperature range. An energy resolution of 1 keV (FWHM) has been obtained for 60 keV photons. The signals consist of two components: A fast one and a slow one, with decay times of 1.5 ms and 30-60 ms, respectively. In this paper we present a simple model which takes thermal and non-thermal phonon processes into account and provides a description of the observed temperature dependence of the pulse shape. The fast component, which completely dominates the signal at low temperatures, is due to high-frequency non-thermal phonons being absorbed in the thermometer. Thermalization of these phonons then leads to a temperature rise of the absorber, which causes the slow thermal component. At the highest operating temperatures (T∼80 mK) the amplitude of the slow component is roughly as expected from the heat capacity of the absorber. The strong suppression of the slow component at low temperatures is explained mostly as a consequence of the weak thermal coupling between electrons and phonons in the thermometer at low temperatures. (orig.)

SUPPLEMENTARY COMPARISON: Final report on supplementary comparison APMP-T-S3-03 of industrial platinum resistance and liquid in glass thermometers from -40 °C to 250 °C

Science.gov (United States)

Norranim, Uthai; Nguyen, Mong Kim; Ballico, Mark J.

2007-01-01

Industrial thermometers such as industrial platinum resistance thermometers (iprts) and liquid-in-glass thermometers (LIGTs) are widely used in industry. Because Key Comparisons are limited to direct realizations of ITS-90, and not all APMP NMIs have participated in them, the national metrology institutes (NMIs) of Thailand and Australia (NIMT and NIMA) organized an APMP supplementary comparison to support the approval of CMCs (calibration and measurement capabilities) for these laboratories. The comparison, performed in 2003, covered the range from -40.0 °C to 250.0 °C, using IPRTs (Hart Scientific 5626-12-S), total immersion (ASTM 62C, 120C) and partial immersion (ASTM 40C) LIGTs. Ten NMIs from the APMP: KIM-LIPI (Indonesia), ITDI (Philippines), MSL (New Zealand), NBSM (Nepal), NMIA (Australia), NIMT (Thailand), SCL (Hong Kong), SIRIM (Malaysia), SPRING (Singapore) and VMI (Vietnam) were divided into two loops to shorten the circulation time, and these were linked by the two pilot laboratories. This report describes details of the artifacts, the circulation schedule, the measurement procedures, the results submitted by participants, uncertainties and the analysis of the results. Reference values calculated using simple mean, median and weighted mean were consistent with each other, but as the Birge criterion was satisfied, the weighted mean with its lower uncertainty was adopted. The artifacts were found to be stable over the comparison and the results of the loop linking labs consistent, allowing an uncertainty of 2 mK to 4 mK to be achieved for the IPRT reference value and 10 mK to 20 mK for the LIGT reference values. These uncertainties allowed the comparison data to be used to adequately test the uncertainties of all the participant laboratories, and hence to directly support their CMC claims. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database

A Fluorescent Thermometer Based on a Pyrene-Labeled Thermoresponsive Polymer

Directory of Open Access Journals (Sweden)

Ulrich S. Schubert

2010-08-01

Full Text Available Thermoresponsive polymers that undergo a solubility transition by variation of the temperature are important materials for the development of ‘smart’ materials. In this contribution we exploit the solubility phase transition of poly(methoxy diethylene glycol methacrylate, which is accompanied by a transition from hydrophilic to hydrophobic, for the development of a fluorescent thermometer. To translate the polymer phase transition into a fluorescent response, the polymer was functionalized with pyrene resulting in a change of the emission based on the microenvironment. This approach led to a soluble polymeric fluorescent thermometer with a temperature range from 11 °C to 21 °C. The polymer phase transition that occurs during sensing is studied in detail by dynamic light scattering.

A Phase-Locked Loop Continuous Wave Sonic Anemometer-Thermometer

DEFF Research Database (Denmark)

Larsen, Søren Ejling; Weller, F. W.; Busings, J. A.

1979-01-01

A continuous wake sonic anemometer-thermometer has been developed for simultaneous measurements of vertical velocity and temperature. The phase angle fluctuations are detected by means of a monolithic integrated phase-locked loop, the latter feature providing for inexpensive and accurate...

Reef coral δ18O thermometer in Hainan island waters, south China sea

International Nuclear Information System (INIS)

He Xuexian; Peng Zicheng; Wang Zhaorong; Huo Weiguo; Tan Jun; Nie Baofu; Chen Tegu; Zhong Jinliang

2000-01-01

An 18-year-long (1981-1998) study was conducted in Hainan Island waters (22 degree 22'N, 110 degree 39'E) to determine the relationship between δ 18 O in skeletal aragonite carbonate and sea surface temperature (SST) in porites lutea of reef-building corals. δ 18 O values in skeletal aragonite carbonate were measured by means of mass spectrometry. Coral samples grew at 5 m depth at Longwan Bay. Monthly measurements of the SST from 1960 to 1998 were taken at Qinglan Bay adjacent to the place of the collected samples. The thermometer shows that SST = -4.16 δ 18 O PDB + 4.9 (r = 0.80) and dδ 18 O/dT = -0.24 per mil/degree C. The δ 18 O thermometer is strongly influenced by the rainfall and runoff. Using the thermometer, the SST in the past hundred years with monthly resolution will be reconstructed and the climatic change in the northern area of South China Sea will be hind cast

Cryogenic particle detectors with superconducting phase transition thermometers

International Nuclear Information System (INIS)

Ferger, P.; Colling, P.; Bucci, C.; Nucciotti, A.; Buehler, M.; Cooper, S.; Feilitzsch, F. v.; Forster, G.; Gabutti, A.; Hoehne, J.; Igalson, J.; Kellner, E.; Loidl, M.; Meier, O.; Nagel, U.; Proebst, F.; Rulofs, A.; Schanda, U.; Seidel, W.; Sisti, M.; Stodolsky, L.; Stolovich, A.; Zerle, L.

1996-01-01

A tungsten superconducting phase transition thermometer on a 32 g sapphire crystal has given an energy resolution of 100 eV (FWHM) for 1.5 keV X-rays, increasing to 440 eV at 14 keV. A possibility to obtain similar resolution in much larger crystals by using Al films as phonon collectors is presented. (orig.)

Study on the KM capacitor base thermometers in the 42-273 K range

International Nuclear Information System (INIS)

Luzganov, V.S.; Mats'ko, A.A.

1988-01-01

Thermometric characteristics of the KM-5a-HZ0 monolithic capacitors in the 42-273 K temperature range are studied. Capacitors capacitance - temperature relation is considered in details. The data reproducibility after 5, 23, 34, 50, 51 and 57 days is studied, the accuracy of temperature measurements by the given thermometers is determined. Recommendations on selection of cpacitors, suitable for application as thermometer, are given. These capacitors permit temperature measurement in the 42-225 K range with the error of ± 0.5 K, and above 225 K the error is ± 1K. 8 refs.; 1 fig.; 1 tab

Genetically encoded ratiometric fluorescent thermometer with wide range and rapid response.

Directory of Open Access Journals (Sweden)

Masahiro Nakano

Full Text Available Temperature is a fundamental physical parameter that plays an important role in biological reactions and events. Although thermometers developed previously have been used to investigate several important phenomena, such as heterogeneous temperature distribution in a single living cell and heat generation in mitochondria, the development of a thermometer with a sensitivity over a wide temperature range and rapid response is still desired to quantify temperature change in not only homeotherms but also poikilotherms from the cellular level to in vivo. To overcome the weaknesses of the conventional thermometers, such as a limitation of applicable species and a low temporal resolution, owing to the narrow temperature range of sensitivity and the thermometry method, respectively, we developed a genetically encoded ratiometric fluorescent temperature indicator, gTEMP, by using two fluorescent proteins with different temperature sensitivities. Our thermometric method enabled a fast tracking of the temperature change with a time resolution of 50 ms. We used this method to observe the spatiotemporal temperature change between the cytoplasm and nucleus in cells, and quantified thermogenesis from the mitochondria matrix in a single living cell after stimulation with carbonyl cyanide 4-(trifluoromethoxyphenylhydrazone, which was an uncoupler of oxidative phosphorylation. Moreover, exploiting the wide temperature range of sensitivity from 5°C to 50°C of gTEMP, we monitored the temperature in a living medaka embryo for 15 hours and showed the feasibility of in vivo thermometry in various living species.

Sequential Probability Ration Tests : Conservative and Robust

NARCIS (Netherlands)

Kleijnen, J.P.C.; Shi, Wen

2017-01-01

In practice, most computers generate simulation outputs sequentially, so it is attractive to analyze these outputs through sequential statistical methods such as sequential probability ratio tests (SPRTs). We investigate several SPRTs for choosing between two hypothesized values for the mean output

Evaluation of a Teaching Kit for Family and Consumer Science Classrooms: Motivating Students to Use a Food Thermometer with Small Cuts of Meat

Science.gov (United States)

Edwards, Zena; Edlefsen, Miriam; Hillers, Virginia; McCurdy, Sandra M.

2005-01-01

The U.S. Dept. of Agriculture recommends use of food thermometers to safely cook small cuts of meat, yet most consumers do not use them. Consumers lack knowledge about how and why to use food thermometers with small cuts of meat. Opportunities exist for family and consumer science classes to provide education about thermometers to adolescents, who…

A gas thermometer for vapor pressure measurements

Science.gov (United States)

Rusin, A. D.

2008-08-01

The pressure of an inert gas over the range 400 1000 K was measured on a tensimetric unit with a quartz membrane pressure gauge of enhanced sensitivity. It was shown that a reactor with a membrane null gauge could be used as a gas thermometer. The experimental confidence pressure and temperature intervals were 0.07 torr and 0.1 K at a significance level of 0.05. A Pt-Pt/10% Rh thermocouple was calibrated; the results were approximated by a polynomial of degree five. The error in temperature calculations was 0.25 K.

Ultrasensitive thermometer for atmospheric pressure operation based on a micromechanical resonator

DEFF Research Database (Denmark)

Cagliani, Alberto; Pini, V.; Tamayo, J.

2014-01-01

For highly integrated systems for bio and chemical analysis a precise and integrated measurement of temperature is of fundamental importance. We have developed an ultrasensitive thermometer based on a micromechanical resonator for operation in air. The high quality factor and the strong temperatu...

Thermodynamics and historical relevance of a jetting thermometer made of Chinese zisha ceramic

Science.gov (United States)

Lee, Vincent; Attinger, Daniel

2016-07-01

Following a recent trend of scientific studies on artwork, we study here the thermodynamics of a thermometer made of zisha ceramic, related to the Chinese tea culture. The thermometer represents a boy who “urinates” shortly after hot water is poured onto his head. Long jetting distance is said to indicate that the water temperature is hot enough to brew tea. Here, a thermodynamic model describes the jetting phenomenon of that pee-pee boy. The study demonstrates how thermal expansion of an interior air pocket causes jetting. A thermodynamic potential is shown to define maximum jetting velocity. Seven optimization criteria to maximize jetting distance are provided, including two dimensionless numbers. Predicted jetting distances, jet durations, and temperatures agree very well with infrared and optical measurements. Specifically, the study confirms that jetting distances are sensitive enough to measure water temperature in the context of tea brewing. Optimization results show that longer jets are produced by large individuals, with low body mass index, with a boyhood of medium size inclined at an angle π/4. The study ends by considering the possibility that ceramic jetting artifacts like the pee-pee boy might have been the first thermometers known to mankind, before Galileo Galilei’s thermoscope.

SPRT Calibration Uncertainties and Internal Quality Control at a Commercial SPRT Calibration Facility

Science.gov (United States)

Wiandt, T. J.

2008-06-01

The Hart Scientific Division of the Fluke Corporation operates two accredited standard platinum resistance thermometer (SPRT) calibration facilities, one at the Hart Scientific factory in Utah, USA, and the other at a service facility in Norwich, UK. The US facility is accredited through National Voluntary Laboratory Accreditation Program (NVLAP), and the UK facility is accredited through UKAS. Both provide SPRT calibrations using similar equipment and procedures, and at similar levels of uncertainty. These uncertainties are among the lowest available commercially. To achieve and maintain low uncertainties, it is required that the calibration procedures be thorough and optimized. However, to minimize customer downtime, it is also important that the instruments be calibrated in a timely manner and returned to the customer. Consequently, subjecting the instrument to repeated calibrations or extensive repeated measurements is not a viable approach. Additionally, these laboratories provide SPRT calibration services involving a wide variety of SPRT designs. These designs behave differently, yet predictably, when subjected to calibration measurements. To this end, an evaluation strategy involving both statistical process control and internal consistency measures is utilized to provide confidence in both the instrument calibration and the calibration process. This article describes the calibration facilities, procedure, uncertainty analysis, and internal quality assurance measures employed in the calibration of SPRTs. Data will be reviewed and generalities will be presented. Finally, challenges and considerations for future improvements will be discussed.

Evaluation of the Use of Optical Fiber Thermometers for Thermal Control of the Quench Module Insert

Science.gov (United States)

Jones, Matthew R.; Farmer, Jeffrey T.; Breeding, Shawn P.

2001-01-01

Issues regarding the use of optical fiber thermometers to control heater settings in a microgravity vacuum furnace are addressed. It is desirable to use these probes in environments such as the International Space Station, because they can be operated without re-calibration for extended periods. However, the analysis presented in this paper shows that temperature readings obtained using optical fiber thermometers can be corrupted by emissions from the fiber when extended portions of the probe are exposed to elevated temperatures.

Use of infrared radiation thermometers for temperature control of plastic and paper webs in electric infrared ovens

International Nuclear Information System (INIS)

Jacobson, D.A.

1985-01-01

Using infrared radiation thermometers in conjunction with infrared heater systems requires special considerations to ensure that accuracy will be achieved. If the thermometer picks up infrared radiation from the heaters, faulty readings can occur. Two methods are generally employed to eliminate this interference. Sight tubes are used to block infrared rays from entering the sensor lens, and a thermometer is chosen which responds to a different wavelength than that being emitted from the infrared heaters. The main types of electric infrared heaters are: (a) screw-in bulbs (shortwave); (b) evacuated tungsten filament tubes (shortwave); (c) quartz tubes (medium wave); (d) quartz panel heaters (medium wave); (e) Ceramic heaters (medium-long wave); (f) metal sheath heaters (medium-long wave). Positioning of a sensor on a production line is dictated by the product being processed and the desired use of the temperature information. The most common location for a sensor is just after the infrared unit. The pyrometer information can be used for setting up the process, for quality control, for heater failure detection, and for control of the heaters. For wide web application in which uniformity across the web is essential, traversing sensors can be used to scan the web to ensure a uniform heating of the product. This information then can be used to control infrared profiling zones which are positioned across the web. In plastics applications, the thermometer most commonly is positioned also at the exit end of the infrared unit. Control functions are similar to those just listed. In some indexing machines, the plastic is sensed while still in the last index station, and the index an be initiated by the thermometer

Hysteresis of thin film IPRTs in the range 100 °C to 600 °C

Science.gov (United States)

Zvizdić, D.; Šestan, D.

2013-09-01

As opposed to SPRTs, the IPRTs succumb to hysteresis when submitted to change of temperature. This uncertainty component, although acknowledged as omnipresent at many other types of sensors (pressure, electrical, magnetic, humidity, etc.) has often been disregarded in their calibration certificates' uncertainty budgets in the past, its determination being costly, time-consuming and not appreciated by customers and manufacturers. In general, hysteresis is a phenomenon that results in a difference in an item's behavior when approached from a different path. Thermal hysteresis results in a difference in resistance at a given temperature based on the thermal history to which the PRTs were exposed. The most prominent factor that contributes to the hysteresis error in an IPRT is a strain within the sensing element caused by the thermal expansion and contraction. The strains that cause hysteresis error are closely related to the strains that cause repeatability error. Therefore, it is typical that PRTs that exhibit small hysteresis also exhibit small repeatability error, and PRTs that exhibit large hysteresis have poor repeatability. Aim of this paper is to provide hysteresis characterization of a batch of IPRTs using the same type of thin-film sensor, encapsulated by same procedure and same company and to estimate to what extent the thermal hysteresis obtained by testing one single thermometer (or few thermometers) can serve as representative of other thermometers of the same type and manufacturer. This investigation should also indicate the range of hysteresis departure between IPRTs of the same type. Hysteresis was determined by cycling IPRTs temperature from 100 °C through intermediate points up to 600 °C and subsequently back to 100 °C. Within that range several typical sub-ranges are investigated: 100 °C to 400 °C, 100 °C to 500 °C, 100 °C to 600 °C, 300 °C to 500 °C and 300 °C to 600 °C . The hysteresis was determined at various temperatures by

The free electron gas primary thermometer using an ordinary bipolar junction transistor approaches ppm accuracy

Science.gov (United States)

Mimila-Arroyo, J.

2017-06-01

In this paper, it is demonstrated that the free electron gas primary thermometer based on a bipolar junction transistor is able to provide the temperature with an accuracy of a few parts per million. Its simple functioning principle exploits the behavior of the collector current when properly biased to extract the temperature. Using general purpose silicon transistors at the water triple point (273.16 K) and gallium melting point (302.9146), an accuracy of a few parts per million has been reached, constituting the simplest and the easiest to operate primary thermometer, that might be considered even for the redefinition of Kelvin.

A High-Resolution Thermometer for the Range 0.75-1.0 K

Science.gov (United States)

Panek, J.; Nash, A.; Larson, M.; Mulders, N.

1999-01-01

We report on a new high-resolution thermometer (HRT) for use near the tricritical point in 3He-4He mixtures. It is based on an existing HRT design that uses a DC-SQUID to detect the magnetization of a paramagnetic sensing element.

Application of kinetic inductance thermometers to x-ray calorimetry

International Nuclear Information System (INIS)

Wai, Y.C.; Labov, S.E.; Silver, E.H.

1990-01-01

A kinetic inductance thermometer is applied to x-ray calorimetry, and its operation over a wide range of frequencies and geometries is discussed. Three amplifier configurations are described, one using a superconducting quantum interference device (SQUID) amplifier, another incorporating an FET amplifier in an amplitude modulated system, and the third, using a tunnel diode frequency modulated oscillator circuit. The predicted performance of each configuration is presented. 13 refs., 6 figs., 1 tab

Optical Fiber Thermometer Based on Fiber Bragg Gratings

Science.gov (United States)

Rosli, Ekbal Bin; Mohd. Noor, Uzer

2018-03-01

Fiber Bragg grating has generated much interest in use as sensors to measure strain, temperature, and other physical parameters. It also the most common component used to develop this sensor with the advantages of simple, intrinsic sensing elements, electrically passive operation, EMI immunity, high sensitivity, compact size and potentially low cost [6]. This paper reports the design of an optical fiber thermometer based on fiber Bragg gratings. The system was developed for detecting temperature and strain by monitoring the shift of Bragg wavelength. The shifting of Bragg wavelength is used to indicate the temperature and strain due to the change in the surrounding temperature and strain. When the temperature and strain reach the exact wavelength level of the system, the temperature and strain value will display on the Arduino liquid crystal display (LCD). The optical fiber will provide the broadband light source and after passing the FBG the Bragg wavelength into the optical spectrum analyzer (OSA). The system is based on FBG as a physical quantity sensor. The temperatures measured is taken from the water bath and that of the strain is provided by amount of slotted mass used. The outcome of this project is to characterize the Bragg wavelength shifting from the fiber Bragg grating output. As the conclusion, this project provides an efficient optical fiber thermometer in measuring temperature and strain in order to replace the use of conventional electrical instruments.

Reexamining age, race, site, and thermometer type as variables affecting temperature measurement in adults – A comparison study

Directory of Open Access Journals (Sweden)

Smith Linda S

2003-06-01

Full Text Available Abstract Background As a result of the recent international vigilance regarding disease assessment, accurate measurement of body temperature has become increasingly important. Yet, trusted low-tech, portable mercury glass thermometers are no longer available. Thus, comparing accuracy of mercury-free thermometers with mercury devices is essential. Study purposes were 1 to examine age, race, site as variables affecting temperature measurement in adults, and 2 to compare clinical accuracy of low-tech Galinstan-in-glass device to mercury-in-glass at oral, axillary, groin, and rectal sites in adults. Methods Setting 176 bed accredited healthcare facility, rural northwest US Participants Convenience sample (N = 120 of hospitalized persons ≥ 18 years old. Instruments Temperatures (°F measured at oral, skin (simultaneous, immediately followed by rectal sites with four each mercury-glass (BD and Galinstan-glass (Geratherm thermometers; 10 minute dwell times. Results Participants averaged 61.6 years (SD 17.9, 188 pounds (SD 55.3; 61% female; race: 85% White, 8.3% Native Am., 4.2% Hispanic, 1.7 % Asian, 0.8% Black. For both mercury and Galinstan-glass thermometers, within-subject temperature readings were highest rectally; followed by oral, then skin sites. Galinstan assessments demonstrated rectal sites 0.91°F > oral and ≅ 1.3°F > skin sites. Devices strongly correlated between and across sites. Site difference scores between devices showed greatest variability at skin sites; least at rectal site. 95% confidence intervals of difference scores by site (°F: oral (0.142 – 0.265, axilla (0.167 – 0.339, groin (0.037 – 0.321, and rectal (-0.111 – 0.111. Race correlated with age, temperature readings each site and device. Conclusion Temperature readings varied by age, race. Mercury readings correlated with Galinstan thermometer readings at all sites. Site mean differences between devices were considered clinically insignificant. Still considered

Assessing the accuracy of globe thermometer method in predicting outdoor mean radiant temperature under Malaysia tropical microclimate

Science.gov (United States)

Khrit, N. G.; Alghoul, M. A.; Sopian, K.; Lahimer, A. A.; Elayeb, O. K.

2017-11-01

Assessing outdoor human thermal comfort and urban climate quality require experimental investigation of microclimatic conditions and their variations in open urban spaces. For this, it is essential to provide quantitative information on air temperature, humidity, wind velocity and mean radiant temperature. These parameters can be quantified directly except mean radiant temperature (Tmrt). The most accurate method to quantify Tmrt is integral radiation measurements (3-D shortwave and long-wave) which require using expensive radiometer instruments. To overcome this limitation the well-known globe thermometer method was suggested to calculate Tmrt. The aim of this study was to assess the possibility of using indoor globe thermometer method in predicting outdoor mean radiant temperature under Malaysia tropical microclimate. Globe thermometer method using small and large sizes of black-painted copper globes (50mm, 150mm) were used to estimate Tmrt and compare it with the reference Tmrt estimated by integral radiation method. The results revealed that the globe thermometer method considerably overestimated Tmrt during the middle of the day and slightly underestimated it in the morning and late evening. The difference between the two methods was obvious when the amount of incoming solar radiation was high. The results also showed that the effect of globe size on the estimated Tmrt is mostly small. Though, the estimated Tmrt by the small globe showed a relatively large amount of scattering caused by rapid changes in radiation and wind speed.

Tympanic ear thermometer assessment of body temperature among patients with cognitive disturbances. An acceptable and ethically desirable alternative?

Science.gov (United States)

Aadal, Lena; Fog, Lisbet; Pedersen, Asger Roer

2016-12-01

Investigation of a possible relation between body temperature measurements by the current generation of tympanic ear and rectal thermometers. In Denmark, a national guideline recommends the rectal measurement. Subsequently, the rectal thermometers and tympanic ear devices are the most frequently used and first choice in Danish hospital wards. Cognitive changes constitute challenges with cooperating in rectal temperature assessments. With regard to diagnosing, ethics, safety and the patients' dignity, the tympanic ear thermometer might comprise a desirable alternative to rectal noninvasive measurement of body temperature during in-hospital-based neurorehabilitation. A prospective, descriptive cohort study. Consecutive inclusion of 27 patients. Linear regression models were used to analyse 284 simultaneous temperature measurements. Ethical approval for this study was granted by the Danish Data Protection Agency, and the study was completed in accordance with the Helsinki Declaration 2008. About 284 simultaneous rectal and ear temperature measurements on 27 patients were analysed. The patient-wise variability of measured temperatures was significantly higher for the ear measurements. Patient-wise linear regressions for the 25 patients with at least three pairs of simultaneous ear and rectal temperature measurements showed large interpatient variability of the association. A linear relationship between the rectal body temperature assessment and the temperature assessment employing the tympanic thermometer is weak. Both measuring methods reflect variance in temperature, but ear measurements showed larger variation. © 2016 Nordic College of Caring Science.

Approximation of the thermometric characteristics of n- and p-GaAs thermodiodes in the 4.2-300 K temperature range and p-GaAs resistance thermometers in the 4.2-100 K temperature range

International Nuclear Information System (INIS)

Logvinenko, S.P.; Derbysheva, S.L.

1978-01-01

The investigation results are reported of various methods for approximating the calibration characteristics of technical resistance thermometers made from p-GaAs and of thermodiodes from n- p-GaAs. The following methods may by used for approximating thermometric characteristics and obtaining calibration tables: method of approximating function describing a physical model (P); method of power polynoms (PP); and the spline method (S). Studies of thermometric characteristics have been achieved in the 4.2-300 K temperature range for thermodiodes, and at 4.2-100 K for thermoresistances. The obtained data show that the use of the S and PP methods for describing monotonous thermometric characteristics of thermodiodes and thermoresistances is equivalent and leads to satisfactory results. Method S affords the best results for describing thermometric characteristics with specific features. The error in approximating thermometric characteristics by method S does not exceed 0.01 K

Performance of Different Light Sources for the Absolute Calibration of Radiation Thermometers

Science.gov (United States)

Martín, M. J.; Mantilla, J. M.; del Campo, D.; Hernanz, M. L.; Pons, A.; Campos, J.

2017-09-01

The evolving mise en pratique for the definition of the kelvin (MeP-K) [1, 2] will, in its forthcoming edition, encourage the realization and dissemination of the thermodynamic temperature either directly (primary thermometry) or indirectly (relative primary thermometry) via fixed points with assigned reference thermodynamic temperatures. In the last years, the Centro Español de Metrología (CEM), in collaboration with the Instituto de Óptica of Consejo Superior de Investigaciones Científicas (IO-CSIC), has developed several setups for absolute calibration of standard radiation thermometers using the radiance method to allow CEM the direct dissemination of the thermodynamic temperature and the assignment of the thermodynamic temperatures to several fixed points. Different calibration facilities based on a monochromator and/or a laser and an integrating sphere have been developed to calibrate CEM's standard radiation thermometers (KE-LP2 and KE-LP4) and filter radiometer (FIRA2). This system is based on the one described in [3] placed in IO-CSIC. Different light sources have been tried and tested for measuring absolute spectral radiance responsivity: a Xe-Hg 500 W lamp, a supercontinuum laser NKT SuperK-EXR20 and a diode laser emitting at 6473 nm with a typical maximum power of 120 mW. Their advantages and disadvantages have been studied such as sensitivity to interferences generated by the laser inside the filter, flux stability generated by the radiant sources and so forth. This paper describes the setups used, the uncertainty budgets and the results obtained for the absolute temperatures of Cu, Co-C, Pt-C and Re-C fixed points, measured with the three thermometers with central wavelengths around 650 nm.

Spatial and Temporal Resolution of a Thin-Wire Resistance Thermometer

DEFF Research Database (Denmark)

Larsen, Søren Ejling; Højstrup, Jørgen

1982-01-01

Based on a discussion of the heat balance equation for a resistance wire sensor a frequency-wavenumber transfer function is derived, which includes the thermal inertia of the wire, the conduction losses to the prongs, and the spatial averaging of the sensor. Based on this transfer function...

Lens transmission measurement for an absolute radiation thermometer

International Nuclear Information System (INIS)

Hao, X.; Yuan, Z.; Lu, X.

2013-01-01

The lens transmission for the National Institute of Metrology of China absolute radiation thermometer is measured by a hybrid method. The results of the lens transmission measurements are 99.002% and 86.792% for filter radiometers with center wavelengths 633 nm and 900 nm, respectively. These results, after correcting for diffraction factors and the size-of-source effect when the lens is incorporated within the radiometer, can be used for measurement of thermodynamic temperature. The expanded uncertainty of the lens transmission measurement system has been evaluated. It is 1.3×10 −3 at 633 nm and 900 nm, respectively

Gamma thermometer allowing absolute and differential temperature measurements

International Nuclear Information System (INIS)

Bottin, P.; Schley, R.

1985-01-01

The gamma thermometer comprises an external envelope containing a cylindrical rod with a central bore and, thick and thin parts defining insulating chambers, at least one thermocouple set in the said central bore; the thermocouple has three junctions connected to one of their end parts by a junction at the level of a thin part, while one at least of the wires comprises two elements made of different materials connected by a junction at the level of a thick part. The present invention applies more particularly for detecting level of the coolant in a nuclear reactor [fr

Correction of the dynamic response of the ''Gamma thermometers'' using a digital filter

International Nuclear Information System (INIS)

Jacquot, J.P.; Lobert, J.P.

1985-01-01

The ''gamma thermometer'' is a sensor used to measure on line the local power inside a PWR nuclear reactor. During transients, this sensor based on thermal exchanges, obes not give a fast response. This paper describes a microprocessor device that allows using a digital filtering technique, a correction of the dynamic response [fr

Modified ultrafast thermometer UFT-M and temperature measurements during Physics of Stratocumulus Top (POST

Directory of Open Access Journals (Sweden)

W. Kumala

2013-08-01

Full Text Available A modified UFT-M version of the ultrafast airborne thermometer UFT, aimed at in-cloud temperature measurements, was designed for the Physics of Stratocumulus Top (POST field campaign. Improvements in its construction resulted in the sensor's increased reliability, which provided valuable measurements in 15 of the 17 flights. Oversampling the data allowed for the effective correction of the artefacts resulting from the interference with electromagnetic transmissions from on-board avionic systems and the thermal noise resulting from the sensor construction. The UFT-M records, when averaged to the 1.4 and 55 m resolutions, compared to the similar records of a thermometer in a Rosemount housing, indicate that the housing distorts even low-resolution airborne temperature measurements. Data collected with the UFT-M during the course of POST characterise the thermal structure of stratocumulus and capping inversion with the maximum resolution of ~1 cm. In this paper, examples of UFT-M records are presented and discussed.

Dual-sensing porphyrin-containing copolymer nanosensor as full-spectrum colorimeter and ultra-sensitive thermometer.

Science.gov (United States)

Yan, Qiang; Yuan, Jinying; Kang, Yan; Cai, Zhinan; Zhou, Lilin; Yin, Yingwu

2010-04-28

A porphyrin-containing copolymer has dual-sensing in response to metal ions and temperature as a novel nanosensor. Triggered by ions, the sensor exhibits full-color tunable behavior as a cationic detector and colorimeter. Responding to temperature, the sensor displays an "isothermal" thermochromic point as an ultra-sensitive thermometer.

Dissociation Pathways of Benzylpyridinium "Thermometer" Ions Depend on the Activation Regime: An IRMPD Spectroscopy Study

NARCIS (Netherlands)

Morsa, D.; Gabelica, V.; Rosu, F.; Oomens, J.; De Pauw, E.

2014-01-01

The dissociation of benzylpyridinium "thermometer" ions is widely used to calibrate the internal energy of ions produced in mass spectrometry. The fragmentation mechanism is usually believed to yield a benzylium cation, although recent studies suggest the possibility of a rearrangement leading to

Measurement of body temperature in 300 dogs with a novel noncontact infrared thermometer on the cornea in comparison to a standard rectal digital thermometer.

Science.gov (United States)

Kreissl, Hannah; Neiger, Reto

2015-01-01

To assess the accuracy of obtaining body temperatures in dogs with a noncontact infrared thermometer (NCIT) on the cornea compared with a rectal digital thermometer (RDT). Prospective single center study. University teaching hospital. Three hundred dogs presented with low, normal, or high body temperatures. Three body temperature readings were measured by an RDT and by an NCIT on the cornea of the left eye by 2 investigators (experienced and inexperienced). Results obtained by the 2 methods were compared. Median body temperature measured by the experienced investigator with the RDT and the NCIT were 38.3°C (range 35.5°C-41.1°C; 95% CI: 38.2-38.4°C) and 37.7°C (35.9°C-40.1°C; 95% CI: 37.7°C-37.9°C), respectively. Measurement of RDT as well as of NCIT correlated well between both investigators (rRDT = 0.94; rNCIT = 0.82; respectively, P temperature correlated poorly (r = 0.43; P temperature >39.0°C) showed an area under the curve of 0.76. Mean discomfort score was significantly lower using NCIT compared to RDT measurement (P temperatures obtained by RDT and NCIT. The corneal NCIT measurement tends to underrecognize hypothermic and hyperthermic conditions. Although the use of the NCIT yields faster results and is significantly more comfortable for the dog than the RDT measurement, it cannot be recommended in dogs at this time. © Veterinary Emergency and Critical Care Society 2015.

Time-Lapse and Slow-Motion Tracking of Temperature Changes: Response Time of a Thermometer

Science.gov (United States)

Moggio, L.; Onorato, P.; Gratton, L. M.; Oss, S.

2017-01-01

We propose the use of a smartphone based time-lapse and slow-motion video techniques together with tracking analysis as valuable tools for investigating thermal processes such as the response time of a thermometer. The two simple experimental activities presented here, suitable also for high school and undergraduate students, allow one to measure…

A calorimetric particle detector using an iridium superconducting phase transition thermometer

International Nuclear Information System (INIS)

Frank, M.; Dummer, D.; Cooper, S.; Igalson, J.; Proebst, F.; Seidel, W.

1994-01-01

We report on a calorimetric particles detector consisting of an 18.3 g silicon crystal and an iridium superconducting phase transition thermometer. The cryogenic calorimeter and the associated apparatus are described in detail. The pulses from irradiation with an α-particle source have a large unexpected overshoot in addition to the component expected from a naive thermal model. The pulse height spectrum displays an energy resolution of 1 percent FWHM at 6 MeV and good linearity. The noise, electrothermal feedback, and position dependence are discussed. (orig.)

The distress thermometer in survivors of gynaecological cancer

DEFF Research Database (Denmark)

Olesen, Mette L.; Hansen, Merete K.; Hansson, Helena

2017-01-01

Purpose: Unrecognised psychological distress among cancer survivors may be identified using short screening tools. We validated the accuracy of the distress thermometer (DT) to detect psychological distress on the Hospital Anxiety and Depression Scale (HADS) among early stage gynaecological cancer...... survivors and whether the women’s DT and HADS scores were associated with the need of an individualised supportive intervention. Methods: One hundred sixty-five gynaecological cancer survivors answered DT and HADS before randomisation in a trial testing a nurse-led, person-centred intervention using...... supportive conversations. The number of conversations was decided in the woman-nurse dyad based on the woman’s perceived need. Nurses were unaware of the women’s DT and HADS scores. We validated DT’s accuracy for screening using HADS as gold standard and receiver operating characteristic curves. Associations...

Temperature measurement in the liquid helium range at pressure

International Nuclear Information System (INIS)

Itskevich, E.S.; Krajdenov, V.F.

1978-01-01

The use of bronze and germanium resistance thermometers and the use of a (Au + 0.07 % Fe)-Cu thermocouple for temperature measurements from 1.5 to 4.2 K in the hydrostatic compression of up to 10 kbar are considered. To this aim, the thermometer resistance as a function of temperature and pressure is measured. It is revealed that pressure does not change the thermometric response of the bronze resistance thermometer but only shifts it to the region of lower temperatures. The identical investigations of the germanium resistance thermometer shows that strong temperature dependence and the shift of its thermometric response under the influence of pressure make the use of germanium resistance thermometers in high-pressure chambers very inconvenient. The results of the analysis of the (Au + 0.07 % Fe) - Cu thermocouple shows that with a 2 per cent accuracy the thermocouple Seebeck coefficient does not depend on pressure. It permits to use this thermocouple for temperature measurements at high pressures

Bilateral comparison for determining the dynamic characteristic values of contact thermometers in fluids

Directory of Open Access Journals (Sweden)

S. Augustin

2018-05-01

Full Text Available In applicable standards and sets of rules (VDI/VDE, 2014; DIN, 2010, 2017, recommendations are made concerning the types of experiments for determining the dynamic parameters in fluids (flowing water and flowing air under well-defined conditions. In the data sheets of the thermometer manufacturers, quite different specifications can be found, such as time percentage values or time constants. Only a few thermometer manufacturers specify the medium and flow conditions under which these parameters have been determined. Above all, it is not common practice to indicate a measurement uncertainty for the dynamic parameters found. In Augustin et al. (2017, a first model for the indication of the measurement uncertainty of dynamic parameters in flowing air was presented.The present paper describes the results of a bilateral comparison made for the first time for determining dynamic parameters in the laboratories of the JUMO GmbH & Co. KG Fulda company and at the Institute of Process Measurement and Sensor Technology of the TU Ilmenau. In doing so, two type-N thermocouples with different diameters were investigated in experimental facilities with flowing water and flowing air. Subsequently, the dynamic parameters found were compared with each other. The differences revealed mainly resulted from plant-specific parameters.

Parent-Child Agreement Using the Spence Children's Anxiety Scale and a Thermometer in Children with Autism Spectrum Disorder

Science.gov (United States)

May, T.; Cornish, K.; Rinehart, N. J.

2015-01-01

Children with Autism Spectrum Disorder (ASD) experience high anxiety which often prompts clinical referral and requires intervention. This study aimed to compare parent and child reports on the Spence Children's Anxiety Scale (SCAS) and a child-reported “worry thermometer” in 88 children aged 8–13 years, 44 with ASD and 44 age, gender, and perceptual IQ matched typically developing children. There were no gender differences in child report on the SCAS and worry thermometers. Results indicated generally good correlations between parent and child self-reported SCAS symptoms for typically developing children but poor agreement in parent-child ASD dyads. The worry thermometer child-report did not reflect child or parent reports on the SCAS. Findings suggest 8–13-year-old children with ASD may have difficulties accurately reporting their anxiety levels. The clinical implications were discussed. PMID:25922765

Method for determining the outlet temperature of fuel assemblies unsupplied with thermometer in WWER-440 reactors

International Nuclear Information System (INIS)

Miko, S.; Kalya, Z.; Hamvas, I.

1987-09-01

The paper outlines a method for the evaluation of the outlet temperatures of fuel assemblies unsupplied with thermometer in WWER-440 reactors. The process is based on interpolation of directly measured assembly temperatures. A quantitative comparison of the errors of described algorithm to those of standard plant-computer interpolation rutine is also presented. (author)

Use of infrared thermometer technique in irrigation scheduling of pomegranate (Punica granatum L. plant

Directory of Open Access Journals (Sweden)

Begüm TEKELİOĞLU

2017-06-01

Full Text Available The main objectives of this study are to assess crop water stress index (CWSI and to determine irrigation schedule of pomegranate using infrared thermometer technique. Treatments with three replications were irrigated every three and six days intervals, as much as 0.50 (S1, 0.75 (S2, 1.00 (S3, and 1.25 (S4 of Class A pan evaporation. Additionally, an unirrigated plot was also formed. The equations obtained for non-water stress baseline is Tc-Ta=0.645VPD-4.338. The equation of full water stressed upper baseline obtained from data taken from branches of pomegranate plant cut in different days is given by Tc-Ta= 0.0489VPD+2.8734. According to the results obtained, it is concluded that infrared thermometer can be used for irrigation scheduling of the pomegranate plants in Antalya conditions. When using this technique in Antalya conditions, it is suggested to keep the seasonal mean CWSI value approximately 0.12 and the index value of 0.40 can be used to start the irrigation. Additionally, it is suggested that the amount of irrigation can be determined as much as the amount of evaporation measured until the index value reaches 0.40.

Thermometer by optical fiber for ampacity studies in overhead transmission lines; Termometro a fibra optica para estudo da ampacidade em linhas de transmissao aereas

Energy Technology Data Exchange (ETDEWEB)

Valente, L.C.G.; Kawase, L.R.; Silva Filho, J.I. da; Silva, J.M.M. da [Centro de Pesquisas de Energia Eletrica, Rio de Janeiro, RJ (Brazil); Igarashi, A.Y. [Universidade Federal, Rio de Janeiro, RJ (Brazil)

1995-12-31

This article suggests the utilization of thermometers constructed from optical fibers technology in overhead power transmission lines. This will help the studies in progress about the electric power systems ampacity. It also presents the advantages of using optical fibers instead of conventional thermometers. As an example, the fact that the optical fibers are dielectric and make possible the remote monitoring. It is also shown a possibility of introducing such measuring system in electric junctions where OPGW cables are used 4 refs., 4 figs.; e-mail: liliana at fis.puc-rio.br

Parent-Child Agreement Using the Spence Children’s Anxiety Scale and a Thermometer in Children with Autism Spectrum Disorder

Directory of Open Access Journals (Sweden)

T. May

2015-01-01

Full Text Available Children with Autism Spectrum Disorder (ASD experience high anxiety which often prompts clinical referral and requires intervention. This study aimed to compare parent and child reports on the Spence Children’s Anxiety Scale (SCAS and a child-reported “worry thermometer” in 88 children aged 8–13 years, 44 with ASD and 44 age, gender, and perceptual IQ matched typically developing children. There were no gender differences in child report on the SCAS and worry thermometers. Results indicated generally good correlations between parent and child self-reported SCAS symptoms for typically developing children but poor agreement in parent-child ASD dyads. The worry thermometer child-report did not reflect child or parent reports on the SCAS. Findings suggest 8–13-year-old children with ASD may have difficulties accurately reporting their anxiety levels. The clinical implications were discussed.

Performance of Magnetic Penetration Thermometers for X-Ray Astronomy

Science.gov (United States)

Nagler, P. C.; Adams, J. S.; Balvin, M. A.; Bandler, S. R.; Denis, K. L.; Hsieh, W. T.; Kelly, D. P.; Porst, J. P.; Sadleir, J. E.; Seidel, G. M.;

Bilateral Comparison Between NIM and NMC Over the Temperature Range from 83.8058 K to 692.677 K

Science.gov (United States)

Sun, Jianping; Ye, Shaochun; Kho, Haoyuan; Zhang, Jintao; Wang, Li

2015-08-01

A bilateral comparison of local realization of the International Temperature Scale of 1990 between the National Institute of Metrology (NIM) and National Metrology Centre (NMC) was carried out over the temperature range from 83.8058 K to 692.677 K. It involved six fixed points including the argon triple point, the mercury triple point, the triple point of water, the melting point of gallium, the freezing point of tin, and the freezing point of zinc. In 2009, NMC asked NIM to participate in a bilateral comparison to link the NMC results to the Consultative Committee for Thermometry Key Comparison 3 (CCT-K3) and facilitate the NMC's calibration and measurement capabilities submission. This comparison was agreed by NIM and Asia Pacific Metrology Programme in 2009, and registered in the Key Comparison Database in 2010 as CCT-K3.2. NMC supplied two fused silica sheath standard platinum resistance thermometers (SPRTs) as traveling standards. One of them was used at the Ga, Sn, and Zn fixed points, while the other one was used at the Ar and Hg fixed points. NMC measured them before and after NIM measured them. During the comparison, a criterion for the SPRT was set as the stability at the triple point of water to be less than 0.3 mK. The results for both laboratories are summarized. A proposal for linking the NMC's comparison results to CCT-K3 is presented. The difference between NMC and NIM and the difference between NMC and the CCT-K3 average reference value using NIM as a link are reported with expanded uncertainties at each measured fixed point.

Designing a TAC thermometer from a VHTR graphite structure

Energy Technology Data Exchange (ETDEWEB)

Smith, James A., E-mail: James.Smith@INL.gov; Kotter, Dale, E-mail: James.Smith@INL.gov [Fuel Performance and Design, Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Garrett, Steven L.; Ali, Randall A. [Graduate Program in Acoustics, Penn State University, State College, PA (United States)

2015-03-31

The interior of a nuclear reactor presents a particularly harsh and challenging environment for both sensors and telemetry due to high temperatures and high fluxes of energetic and ionizing particles among the radioactive decay products. Very High Temperature Reactors are pushing the in core temperatures even higher. A unique sensing approach will be discussed to address the necessary high temperature measurements. Thermoacoustic thermometry exploits high temperatures and uses materials that are immune to the effects of ionizing radiation to create a temperature sensor that is self-powered and wireless. In addition, the form-factor for the Thermoacoustic Thermometer (TACT) can be designed to be integrated within common in-pile structures. There are no physical moving parts required for TACT and the sensor is self-powered, as it uses the nuclear fuel for its heat source. TACT data will be presented from a laboratory prototype mimicking the design necessary for a VHTR graphite structure.

A comparison of absolute calibrations of a radiation thermometer based on a monochromator and a tunable source

Energy Technology Data Exchange (ETDEWEB)

Keawprasert, T. [National Institute of Metrology Thailand, Pathum thani (Thailand); Anhalt, K.; Taubert, D. R.; Sperling, A.; Schuster, M.; Nevas, S. [Physikalisch Technische Bundesanstalt, Braunschweig and Berlin (Germany)

2013-09-11

An LP3 radiation thermometer was absolutely calibrated at a newly developed monochromator-based set-up and the TUneable Lasers in Photometry (TULIP) facility of PTB in the wavelength range from 400 nm to 1100 nm. At both facilities, the spectral radiation of the respective sources irradiates an integrating sphere, thus generating uniform radiance across its precision aperture. The spectral irradiance of the integrating sphere is determined via an effective area of a precision aperture and a Si trap detector, traceable to the primary cryogenic radiometer of PTB. Due to the limited output power from the monochromator, the absolute calibration was performed with the measurement uncertainty of 0.17 % (k= 1), while the respective uncertainty at the TULIP facility is 0.14 %. Calibration results obtained by the two facilities were compared in terms of spectral radiance responsivity, effective wavelength and integral responsivity. It was found that the measurement results in integral responsivity at the both facilities are in agreement within the expanded uncertainty (k= 2). To verify the calibration accuracy, the absolutely calibrated radiation thermometer was used to measure the thermodynamic freezing temperatures of the PTB gold fixed-point blackbody.

A comparison of absolute calibrations of a radiation thermometer based on a monochromator and a tunable source

International Nuclear Information System (INIS)

Keawprasert, T.; Anhalt, K.; Taubert, D. R.; Sperling, A.; Schuster, M.; Nevas, S.

2013-01-01

An LP3 radiation thermometer was absolutely calibrated at a newly developed monochromator-based set-up and the TUneable Lasers in Photometry (TULIP) facility of PTB in the wavelength range from 400 nm to 1100 nm. At both facilities, the spectral radiation of the respective sources irradiates an integrating sphere, thus generating uniform radiance across its precision aperture. The spectral irradiance of the integrating sphere is determined via an effective area of a precision aperture and a Si trap detector, traceable to the primary cryogenic radiometer of PTB. Due to the limited output power from the monochromator, the absolute calibration was performed with the measurement uncertainty of 0.17 % (k= 1), while the respective uncertainty at the TULIP facility is 0.14 %. Calibration results obtained by the two facilities were compared in terms of spectral radiance responsivity, effective wavelength and integral responsivity. It was found that the measurement results in integral responsivity at the both facilities are in agreement within the expanded uncertainty (k= 2). To verify the calibration accuracy, the absolutely calibrated radiation thermometer was used to measure the thermodynamic freezing temperatures of the PTB gold fixed-point blackbody

Comparison between auricular and standard rectal thermometers for the measurement of body temperature in dogs.

Science.gov (United States)

Sousa, Marlos G; Carareto, Roberta; Pereira-Junior, Valdo A; Aquino, Monally C C

2011-04-01

Although the rectal mucosa remains the traditional site for measuring body temperature in dogs, an increasing number of clinicians have been using auricular temperature to estimate core body temperature. In this study, 88 mature healthy dogs had body temperatures measured with auricular and rectal thermometers. The mean temperature and confidence intervals were similar for each method, but Bland-Altman plots showed high biases and limits of agreement unacceptable for clinical purposes. The results indicate that auricular and rectal temperatures should not be interpreted interchangeably.

Comparative study of on-line response time measurement methods for platinum resistance thermometer

International Nuclear Information System (INIS)

Zwingelstein, G.; Gopal, R.

1979-01-01

This study deals with the in site determination of the response time of platinum resistance sensor. In the first part of this work, two methods furnishing the reference response time of the sensors are studied. In the second part of the work, two methods obtaining the response time without dismounting of the sensor, are studied. A comparative study of the performances of these methods is included for fluid velocities varying from 0 to 10 m/sec, in both laboratory and plant conditions

Stability Studies of a New Design Au/Pt Thermocouple Without a Strain Relieving Coil

Science.gov (United States)

Jahan, Ferdouse; Ballico, Mark

2007-12-01

The performance of a simple, new design Au/Pt thermocouple developed by NMIA is assessed. This thermocouple is proposed as a more accurate replacement, over the temperature range from 0 to 1,000°C, for the commonly used Type R and S industrial transfer standards, in a robust form familiar to industrial calibration laboratories. Due to the significantly different thermal expansions of the Au and Pt thermoelements, reported designs of the Au/Pt thermocouple incorporate a strain-relieving coil or bridge at the thermocouple junction. As the strain relieving coil is mechanically delicate, these thermocouples are usually mounted in a protective quartz tube assembly, like a standard platinum resistance thermometer (SPRT). Although providing uncertainties at the mK level, they are more delicate than the commonly used Type R and S thermocouples. A new and simple design of the Au/Pt thermocouple was developed in which the differential thermal expansion between Au and Pt is accommodated in the thermocouple leads, facilitated by a special head design. The resulting thermocouple has the appearance and robustness of the traditional Type R and S thermocouples, while retaining stability better than 10 mK up to 961°C. Three thermocouples of this design were calibrated at fixed points and by comparison to SPRTs in a stirred salt bath. In order to assess possible impurity migration, strain effects, and mechanical robustness, sequences of heat treatment up to a total of 500 h together with over 50 thermal cycles from 900°C to ambient were performed. The effect of these treatments on the calibration was assessed, demonstrating the sensors to be robust and stable to better than 10 mK. The effects on the measured inhomogeneity of the thermocouple were assessed using the NMIA thermocouple scanning bath.

Experimental study of temperature sensor for an ocean-going liquid hydrogen (LH2) carrier

Science.gov (United States)

Nakano, A.; Shimazaki, T.; Sekiya, M.; Shiozawa, H.; Aoyagi, A.; Ohtsuka, K.; Iwakiri, T.; Mikami, Z.; Sato, M.; Kinoshita, K.; Matsuoka, T.; Takayama, Y.; Yamamoto, K.

2018-04-01

The prototype temperature sensors for an ocean-going liquid hydrogen (LH2) carrier were manufactured by way of trial. All of the sensors adopted Platinum 1000 (PT-1000) resistance thermometer elements. Various configurations of preproduction temperature sensors were tested in AIST's LH2 test facility. In the experiments, a PT-1000 resistance thermometer, calibrated at the National Metrology Institute of Japan at AIST, was used as the standard thermometer. The temperatures measured by the preproduction sensors were compared with the temperatures measured by the standard thermometer, and the measurement accuracy of the temperature sensors in LH2 was investigated and discussed. It was confirmed that the measurement accuracies of the preproduction temperature sensors were within ±50 mK, which is the required measurement accuracy for a technical demonstration ocean-going LH2 carrier.

A Field Assessment of a Prototype Meter for Measuring the Wet-Bulb Globe-Thermometer Index

Science.gov (United States)

Walters, J. D.

1968-01-01

A prototype electronic instrument for the direct measurement of the wet-bulb globe-thermometer index is described. An assessment is made of its accuracy, as compared with W.B.G.T. indices calculated from conventional thermometric data, and a comparison is made between W.B.G.T. values read from the meter and effective or corrected effective temperatures derived from separate thermometric and air velocity recording instruments in the same climates. The instrument proved to be reliable and accurate over a wide range of climates and is a useful self-contained device for use in habitability surveys and similar investigations. Images PMID:5663429

Gamma thermometer longevity test: Laguna Verde 2 instruments recent performance

International Nuclear Information System (INIS)

Cuevas V, G.; Avila N, A.; Calleros M, G.

2013-10-01

This paper is informative of the General Electric Hitachi and Global Nuclear Fuel - Americas are collaboration with Comision Federal de Electricidad in a longevity test of thermocouples as power monitoring devices. The test conclusions will serve for final engineering design in detailing the Automated Fixed In-core Probes for calibration of the Local Power Range Monitors (LPRMs) of the Economic Simplified Boiling Water Reactor. This paper introduces the collaboration description and some recent performance evaluation of the thermocouples that are sensitive to gamma radiation and are known generically as Gamma Thermometers (G T). The G Ts in Laguna Verde 2 are radially located inside six instrumentation tubes in the core and consist of seven thermocouples, four are aligned with the LPRM heights and three are axially located between LPRM heights. The Laguna Verde 2 G T test has become the longest test of thermocouples as power monitoring devices in a BWR industry history and confirms their reliability in terms of time-dependent small noise under steady state reactor conditions and good agreement against Traversing In-core Probes power measurements. (Author)

Gamma thermometer longevity test: Laguna Verde 2 instruments recent performance

Energy Technology Data Exchange (ETDEWEB)

Cuevas V, G. [Global Nuclear Fuel, Americas, 3901 Castle Hayne Road, Wilmington, North Carolina (United States); Avila N, A.; Calleros M, G., E-mail: Gabriel.Cuevas-Vivas@gnf.com [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verda, Carretera Veracruz-Nautla Km 42.5, Alto Lucero, Veracruz (Mexico)

2013-10-15

This paper is informative of the General Electric Hitachi and Global Nuclear Fuel - Americas are collaboration with Comision Federal de Electricidad in a longevity test of thermocouples as power monitoring devices. The test conclusions will serve for final engineering design in detailing the Automated Fixed In-core Probes for calibration of the Local Power Range Monitors (LPRMs) of the Economic Simplified Boiling Water Reactor. This paper introduces the collaboration description and some recent performance evaluation of the thermocouples that are sensitive to gamma radiation and are known generically as Gamma Thermometers (G T). The G Ts in Laguna Verde 2 are radially located inside six instrumentation tubes in the core and consist of seven thermocouples, four are aligned with the LPRM heights and three are axially located between LPRM heights. The Laguna Verde 2 G T test has become the longest test of thermocouples as power monitoring devices in a BWR industry history and confirms their reliability in terms of time-dependent small noise under steady state reactor conditions and good agreement against Traversing In-core Probes power measurements. (Author)

Measurement Techniques for Flow Diagnostic in ITAM Impulse Wind Tunnels

Science.gov (United States)

2010-04-01

whose acoustic resistance is identical to that of the piezoelement material. To attenuate the effect of vibrations of the casing 4 and model walls...mercury thermometers, resistance thermometers, thermocouples, optical pyrometers , and a number of spectroscopic methods have gained widespread...known method of optical pyrometers , which allows temperature measurements above 1600°С. As it is well known this method is based on using the laws of

A 6-bit 4 GS/s pseudo-thermometer segmented CMOS DAC

Science.gov (United States)

Yijun, Song; Wenyuan, Li

2014-06-01

A 6-bit 4 GS/s, high-speed and power-efficient DAC for ultra-high-speed transceivers in 60 GHz band millimeter wave technology is presented. A novel pseudo-thermometer architecture is proposed to realize a good compromise between the fast conversion speed and the chip area. Symmetrical and compact floor planning and layout techniques including tree-like routing, cross-quading and common-centroid method are adopted to guarantee the chip is fully functional up to near-Nyquist frequency in a standard 0.18 μm CMOS process. Post simulation results corroborate the feasibility of the designed DAC, which canperform good static and dynamic linearity without calibration. DNL errors and INL errors can be controlled within ±0.28 LSB and ±0.26 LSB, respectively. SFDR at 4 GHz clock frequency for a 1.9 GHz near-Nyquist sinusoidal output signal is 40.83 dB and the power dissipation is less than 37 mW.

A 6-bit 4 GS/s pseudo-thermometer segmented CMOS DAC

International Nuclear Information System (INIS)

Song Yijun; Li Wenyuan

2014-01-01

A 6-bit 4 GS/s, high-speed and power-efficient DAC for ultra-high-speed transceivers in 60 GHz band millimeter wave technology is presented. A novel pseudo-thermometer architecture is proposed to realize a good compromise between the fast conversion speed and the chip area. Symmetrical and compact floor planning and layout techniques including tree-like routing, cross-quading and common-centroid method are adopted to guarantee the chip is fully functional up to near-Nyquist frequency in a standard 0.18 μm CMOS process. Post simulation results corroborate the feasibility of the designed DAC, which canperform good static and dynamic linearity without calibration. DNL errors and INL errors can be controlled within ±0.28 LSB and ±0.26 LSB, respectively. SFDR at 4 GHz clock frequency for a 1.9 GHz near-Nyquist sinusoidal output signal is 40.83 dB and the power dissipation is less than 37 mW. (semiconductor integrated circuits)

A comparative study on accuracy of liquid crystal forehead, digital electronic axillary, infrared tympanic with glass-mercury rectal thermometer in infants and young children.

Science.gov (United States)

Kongpanichkul, A; Bunjongpak, S

2000-09-01

This study was carried out to assess the accuracy of three devices namely, liquid crystal forehead, digital electronic axillary and infrared tympanic thermometer, using a glass-mercury rectal thermometer as the control. The subjects were two hundred children aged 0-48 months. The mean rectal temperature was 38.0 +/- 0.91 degrees C; forehead, 37.83 +/- 0.94 degrees C; tympanic, 37.77 +/- 0.95 degrees C, and axillary, 37.71 +/- 0.86 degrees C. Compared to the rectal temperature, all values were significantly lower (p < 0.05). Forehead, tympanic and axillary temperature differed from rectal temperature by at least 0.5 degrees C in 33.33 per cent, 23.5 per cent and 31.5 per cent of subjects, and at least 1 degrees C in 22 per cent, 1 per cent and 6 per cent of subjects respectively. Accuracy in detection of fever was 79 per cent for forehead, 85.5 per cent for tympanic and 84 per cent for axillary thermometry. Sensitivity of the three devices was 67-83 per cent in detection of fever and 64-77 per cent in detection of high fever. Tympanic thermometry had the best performance while forehead thermometry had the poorest. After using revised diagnostic threshold temperature by ROC curves, sensitivity of each device improved but accuracy was nearly the same. It is concluded that the three devices are not suitable as a substitute for a glass-mercury rectal thermometer in assessment of fever in infants and young children.

Dealing with the size-of-source effect in the calibration of direct-reading radiation thermometer

Energy Technology Data Exchange (ETDEWEB)

Saunders, P. [Measurement Standards Laboratory of New Zealand, PO Box 31-310, Lower Hutt 5040 (New Zealand)

2013-09-11

The majority of general-purpose low-temperature handheld radiation thermometers are severely affected by the size-of-source effect (SSE). Calibration of these instruments is pointless unless the SSE is accounted for in the calibration process. Traditional SSE measurement techniques, however, are costly and time consuming, and because the instruments are direct-reading in temperature, traditional SSE results are not easily interpretable, particularly by the general user. This paper describes a simplified method for measuring the SSE, suitable for second-tier calibration laboratories and requiring no additional equipment, and proposes a means of reporting SSE results on a calibration certificate that should be easily understood by the non-specialist user.

Magnetic Criticality Enhanced Hybrid Nanodiamond Thermometer under Ambient Conditions

Science.gov (United States)

Wang, Ning; Liu, Gang-Qin; Leong, Weng-Hang; Zeng, Hualing; Feng, Xi; Li, Si-Hong; Dolde, Florian; Fedder, Helmut; Wrachtrup, Jörg; Cui, Xiao-Dong; Yang, Sen; Li, Quan; Liu, Ren-Bao

2018-01-01

Nitrogen-vacancy (NV) centers in diamond are attractive as quantum sensors owing to their superb coherence under ambient conditions. However, the NV center spin resonances are relatively insensitive to some important parameters such as temperature and pressure. Here we design and experimentally demonstrate a hybrid nanothermometer composed of NV centers and a magnetic nanoparticle (MNP), in which the temperature sensitivity is enhanced by the critical magnetization of the MNP near the ferromagnetic-paramagnetic transition temperature. The temperature susceptibility of the NV center spin resonance reaches 14 MHz /K , nearly 200 times larger than that of bare NV centers. The sensitivity of a hybrid nanothermometer composed of a Cu1 -xNix MNP and a nanodiamond is measured to be 11 mK /√{Hz } under ambient conditions. The working range of the hybrid thermometer can be designed from cryogenic temperature to about 600 K by tuning the chemical composition of the Cu1 -xNix MNP. We demonstrate in situ detection of the magnetic phase transition of a single magnetic nanoparticle using the hybrid nanothermometer. This hybrid nanothermometer provides a novel approach to studying a broad range of thermal processes at nanoscales such as nanoplasmonics, heat-stimulated subcellular processes, and thermodynamics of nanosystems.

Magnetic Criticality Enhanced Hybrid Nanodiamond Thermometer under Ambient Conditions

Directory of Open Access Journals (Sweden)

Ning Wang

2018-03-01

Full Text Available Nitrogen-vacancy (NV centers in diamond are attractive as quantum sensors owing to their superb coherence under ambient conditions. However, the NV center spin resonances are relatively insensitive to some important parameters such as temperature and pressure. Here we design and experimentally demonstrate a hybrid nanothermometer composed of NV centers and a magnetic nanoparticle (MNP, in which the temperature sensitivity is enhanced by the critical magnetization of the MNP near the ferromagnetic-paramagnetic transition temperature. The temperature susceptibility of the NV center spin resonance reaches 14  MHz/K, nearly 200 times larger than that of bare NV centers. The sensitivity of a hybrid nanothermometer composed of a Cu_{1-x}Ni_{x} MNP and a nanodiamond is measured to be 11  mK/sqrt[Hz] under ambient conditions. The working range of the hybrid thermometer can be designed from cryogenic temperature to about 600 K by tuning the chemical composition of the Cu_{1-x}Ni_{x} MNP. We demonstrate in situ detection of the magnetic phase transition of a single magnetic nanoparticle using the hybrid nanothermometer. This hybrid nanothermometer provides a novel approach to studying a broad range of thermal processes at nanoscales such as nanoplasmonics, heat-stimulated subcellular processes, and thermodynamics of nanosystems.

Thermometry for the LHC

International Nuclear Information System (INIS)

Buhler, S.; Junquera, T.; Thermeau, J.P.

1999-01-01

The LHC project will use about 8000 thermometers to control the temperature of magnets. These thermometers will be operated at a temperature ranging from 1.6 K to 300 K and their calibration should be better than 0.25%. A small cryogenic thermometer calibration facility has been designed and tested. To select the cryogenic temperature sensors, an irradiation program is being performed to expose at high neutron fluences (>10 15 n/cm 2 ) the following thermometers: carbon resistors, Ge, thin film, RhFe and Pt. The resistance shifts under radiation of the different sensors at liquid helium are presented. (authors)

SQUIDs in thermal detectors of weakly interacting particles

International Nuclear Information System (INIS)

Trofimov, V.N.

1991-01-01

The application of four different types of SQUID-assisted thermometers for cryogenic thermal detectors of weakly interacting particles is analyzed with two of them for the first time. The classic resistive thermometer is considered as well for the comparison. Original results of testing the detector with working temperature of 1K and thermocouple thermometer with SQUID are given. The conclusion is made that temperature resolution of 10 -10 kHz -1/2 or energy sensitivity of 1-10 eV per 1 kg of detector mass can be achieved when using the SQUID-assisted thermometers. 12 refs.; 7 figs.; 1 tab

Temperature and other data were collected using thermometer and bottle casts in the Chukchi and Bering Sea from 1947-02-11 to 1949-07-26 (NODC Accession 9700081)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Temperature, depth, oxygen, and salinity data were collected using thermometer and bottle casts from the USS CACOPAN, USS NEREUS, and HMCS CEDARWOOD in the Chukchi...

A monocrystal of 59Co as a nuclear orientation thermometer in neutron experiments with oriented targets

International Nuclear Information System (INIS)

Fasoli, U.; Galeazzi, G.; Pavan, P.; Toniolo, D.; Zago, G.; Zannoni, R.

1980-01-01

An apparatus for measuring temperatures in the millikelvin region is described based on the 'deformation effect' on fast neutron transmission through an aligned 59 Co monocrystal, employing a 252 Cf pill as the neutron source. A statistical accuracy of a few percent in a few minutes is obtainable with a heat input of some tens of pW. The apparatus is suitable in neutron experiments with oriented targets when the gamma-ray background hinders the use of gamma-ray anisotropy thermometers. In these and similar cases, in which the temperature must be held constant for long periods, the large heat capacity of the cobalt sample is not a drawback. (orig.)

Stand development and reliability tests of the thermal monitoring means for NPP

International Nuclear Information System (INIS)

Nalivaev, V.I.; Nikul'shin, V.S.; Kichigin, A.B.; Dirin, V.F.

2003-01-01

The paper is devoted to the reliability tests of thermoelectric thermometers and resistance thermometers during their operation in the nominal mode. Five stands Reliability are developed and operate for realization of tests of all manufactured thermal converters. delivered at NPP. Description of all stands are presented [ru

The Air Force Weapons Laboratory Skid Resistance Research Program, 1969- 1974

Science.gov (United States)

1975-05-01

M(d) The slope measuring device consists of a rectangular section of aluminum (10-ft lonq, 5/8-in thick, and 2-1/2-in high) with machinists levels...pipe lines, meters, weight buckets, spray bars, and other containers of flow lines. i. Thermometric Equipment, An armored thermometer with a range from...shall be further equipped with an approved dial-scale mercury-actuated thermometer, an electric pyrometer, or other approved thermometric instruments

Magnetic Thermometer: Thermal effect on the Agglomeration of Magnetic Nanoparticles by Magnetic field

Science.gov (United States)

Jin, Daeseong; Kim, Hackjin

2018-03-01

We have investigated the agglomeration of magnetite nanoparticles in the aqueous solution under magnetic field by measuring temporal change of magnetic weight. The magnetic weight corresponds to the force due to the magnetization of magnetic materials. Superparamagnetic magnetite nanoparticles are synthesized and used in this work. When the aqueous solution of magnetite nanoparticle is placed under magnetic field, the magnetic weight of the sample jumps instantaneously by Neel and Brown mechanisms and thereafter increases steadily following a stretched exponential function as the nanoparticles agglomerate, which results from the distribution of energy barriers involved in the dynamics. Thermal motions of nanoparticles in the agglomerate perturb the ordered structure of the agglomerate to reduce the magnetic weight. Fluctuation of the structural order of the agglomerate by temperature change is much faster than the formation of agglomerate and explained well with the Boltzmann distribution, which suggests that the magnetic weight of the agglomerate works as a magnetic thermometer.

Measurement of temperature distributions in large pool fires with the use of directional flame thermometers

International Nuclear Information System (INIS)

Koski, Jorman A.

2000-01-01

Temperatures inside the flame zone of large regulatory pool fires measured during tests of radioactive materials packages vary widely with both time and position. Measurements made with several Directional Flame Thermometers, in which a thermocouple is attached to a thin metal sheet that quickly approaches flame temperatures, have been used to construct fire temperature distributions and cumulative probability distributions. As an aid to computer simulations of these large fires, these distributions are presented. The distributions are constructed by sorting fire temperature data into bins 10 C wide. A typical fire temperature distribution curve has a gradual increase starting at about 600 C, with the number of observations increasing to a peak near 1000 C, followed by an abrupt decrease in frequency, with no temperatures observed above 1200 C

Report on NIM-NMC bilateral comparison: SPRT calibration comparison from -190°C to 420°C

Science.gov (United States)

Sun, Jianping; Ye, Shaochun; Wang, Li; Zhang, Jintao; Kho, Haoyuan

2016-01-01

A bilateral comparison of local realization of the International temperature scale of 1990 (ITS-90) between National Institute of Metrology (NIM) and National Metrology Centre (NMC) was carried out over the temperature range from -190°C to 420°C. It involved six fixed points including the argon triple point, the mercury triple point, the triple point of water, the melting point of gallium, the freezing point of tin and the freezing point of zinc. In 2009, NMC asked NIM to participate in a bilateral comparison to link the NMC results to the Consultative Committee for Thermometry Key comparison 3 (CCT-K3) and facilitate the NMC's Calibration and measurement capabilities (CMCs) submission. This comparison was agreed by NIM and Asia Pacific Metrology Programme (APMP) in 2009, and registered in the Key Comparison Database (KCDB) in 2010 as CCT-K3.2. NMC supplied two 25 Ω fused silica sheath standard platinum resistance thermometers (SPRTs) as traveling standards. One of them was used at the Ga, Sn and Zn fixed points, while the other one was used at the Ar and Hg fixed point. NMC measured them before and after NIM measurement. During the comparison, a criterion for the SPRT was set as the stability at the triple point of water to be less than 0.3 mK. The results for both laboratories are summarized. A proposal for linking the NMC's comparison results to CCT-K3 is presented. The difference between NMC and NIM and the difference between NMC and the CCT-K3 Average Reference Value (ARV) using NIM as a link are reported with expanded uncertainties at each measured fixed point. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCT, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Linearization of resistance thermometers and other transducers

DEFF Research Database (Denmark)

Diamond, Joseph M.

1970-01-01

deflection output or to null balance output. The application to the common temperature transducers is considered. It is shown that thermistors, linear metals (e.g., copper), and nickel can be linearized in terms of temperature, but platinum cannot be. If linearization is desired in terms of the reciprocal...

The Standard Temperature Calibration Center of the CEN Saclay

International Nuclear Information System (INIS)

Liermann, J.

1978-01-01

The first part of this article describes the instruments available at the Standard Temperature Calibration Center of the CEN Saclay. At the moment the Center has been approved by the BNM to make calibrations between 0 and 1050 0 C, but the Center has recently developed some ovens which will allow calibrations up to 2000 0 C. The Center can also perform thermal and mechanical tests on detector components under the influence of external factors. The second part concerns the development of platinum-resistance high temperature thermometer. The calibrations by comparison between 0 and 1000 0 C are, at the moment, made by using platinum resistance thermometer as a reference up to 630 0 C and a platinum-rhodied/platinum thermocouple above 630 0 C. The use of only one reference could represent for a calibration center a great improvement. For this reason a platinum-resistance high temperature thermometer has been developed. Great care was taken during the conceptual design and during the selection and the assembly of each component [fr

Surface temperature measurements on superconducting cavities in superfluid helium

International Nuclear Information System (INIS)

Fouaidy, T.; Junquera, T.; Caruette, A.

1991-01-01

Two thermometry systems have been developed: a scanning thermometer system routinely used for the 1.5 GHz monocell cavity studies and a fixed thermometer array used to investigate spatial surface resistance distribution on various SC removable endplates of a cylindrical TE011mode cavity. Thermometers used in these systems are thermally insulated from the surrounding HeII bath by an epoxy housing ('epoxy'thermometers). Accurate calibration of the fixed thermometers was conducted by using different test cells and the experimental results were compared to model calculations performed with a finite element computational code. Measured thermometer efficiency and linearity are in good agreement with numerical results. Some typical temperature maps of different Nb samples obtained with the TE011 array (40 epoxy thermometers) are discussed. On the basis of numerical modelling results, a new type of thermometer with an improved efficiency has been designed. The thermal insulation against Helium II has been drastically improved by placing the sensitive part of the thermometer in a small vacuum jacket ('vacuum' thermometers). Two main goals have been reached with the first prototypes: improved efficiency by a factor of 2.5 - 3, and a bath temperature dependence of the thermal response in good agreement with the expected Kapitza conductance behaviour. Fitting experimental results with numerical modelling data, allow us to estimate the Kapitza conductance. The obtained values are in good agreement with the previous results reported by several authors using a different measurement method. The 'vacuum' thermometers are currently used on the TE011 mode cavity with Nb and NbTiN plates and the first results are presented

Determination of mean molecular weights in organic reactor coolants. III. Differential cryoscopy with thermoelectric thermometer

International Nuclear Information System (INIS)

Becerro, E.; Carreira, M.

1968-01-01

The solubility problems raised by some components of the polymeric residue of irradiated polyphenolic coolants, which make it necessary to operate with very small samples, have been solved by means of a differential cryoscopic technique using a thermoelectric thermometer (thermal) as sensitive element. The method is based on the direct measurement of the difference between the freezing points of the investigated solution and of a reference solution whose concentration may be changed at will. The change of Δ V (mV) versus c(molal) is linear, the equivalent point being determined either analytically or graphically depending on the required accuracy. The method has been tested by measurements on pure polyphenyls, using diphenyl ether as solvent. It has been also applied to the main prospective coolants for the DON reactor. Working with 10 2 molal solutions the accuracy is better than ± 2 per cent. (Author) 2 refs

Thermometric characteristics of some 1/8W carbon resistors in the millikelvin range

International Nuclear Information System (INIS)

Radebaugh, R.; Holste, J.C.; Siegwarth, J.D.

1974-01-01

Gotch and Awano (Cryogenic Engineering (Tokyo); 8:18 (1973)) have reported on the useful characteristics of 1/8W 100Ω Matsushita carbon resistors (grade ERC-18GK) as thermometers for the region 0.4K and 4.2K. Measurements on the resistance characteristics of this grade of resistors from 11mK to 1K are reported here. Nominal resistances of 56Ω, 68Ω, 82Ω, 100Ω, and 220Ω have been measured. It is found that the 56Ω, 68Ω and 82 Ω resistors make useful thermometers down to at least 11mK. A comparison of the resistance behaviour of units immersed in dilute He 3 -He 4 with those outside the liquid is also made. (author)

The application of infrared thermometric technology in the nuclear industry

International Nuclear Information System (INIS)

Wang Wenjin

1992-04-01

In the process of bituminization of low level waste liquid, to measure the surface temperature of a moving barrel filled with waste liquid and bitumen is essential. Thus, a special infrared thermometer is developed. The property of radiation resistance for the lithium tantalate prober which is a main part of the thermometer was carefully tested. The test results show that in the nuclear industry the infrared thermometric technology is applicable

Operational methods of thermodynamics. Volume 1 - Temperature measurement

Science.gov (United States)

Eder, F. X.

The principles of thermometry are examined, taking into account the concept of temperature, the Kelvin scale, the statistical theory of heat, negative absolute temperatures, the thermodynamic temperature scale, the thermodynamic temperature scale below 1 K, noise thermometry, temperature scales based on black-body radiation, acoustical thermometry, and the International Practical Temperature Scale 1968. Aspects of practical temperature measurement are discussed, giving attention to thermometers based on the expansion of a gas or a liquid, instruments utilizing the relative thermal expansion of two different metals, devices measuring the vapor pressure of a liquid, thermocouples, resistance thermometers, radiation pyrometers of various types, instruments utilizing the temperature dependence of a number of material characteristics, devices for temperature control, thermometer calibration, and aspects of thermometer installation and inertia. A description is presented of the approaches employed for the measurement of low temperatures.

Magnetic Nanoparticle Thermometer: An Investigation of Minimum Error Transmission Path and AC Bias Error

Directory of Open Access Journals (Sweden)

Zhongzhou Du

2015-04-01

Full Text Available The signal transmission module of a magnetic nanoparticle thermometer (MNPT was established in this study to analyze the error sources introduced during the signal flow in the hardware system. The underlying error sources that significantly affected the precision of the MNPT were determined through mathematical modeling and simulation. A transfer module path with the minimum error in the hardware system was then proposed through the analysis of the variations of the system error caused by the significant error sources when the signal flew through the signal transmission module. In addition, a system parameter, named the signal-to-AC bias ratio (i.e., the ratio between the signal and AC bias, was identified as a direct determinant of the precision of the measured temperature. The temperature error was below 0.1 K when the signal-to-AC bias ratio was higher than 80 dB, and other system errors were not considered. The temperature error was below 0.1 K in the experiments with a commercial magnetic fluid (Sample SOR-10, Ocean Nanotechnology, Springdale, AR, USA when the hardware system of the MNPT was designed with the aforementioned method.

Use of the distress thermometer to evaluate symptoms, outcome and satisfaction in a specialist psycho-oncology service.

Science.gov (United States)

Blenkiron, Paul; Brooks, Alexander; Dearden, Richard; McVey, Joanne

2014-01-01

The National Institute for Health and Care Excellence recommends the use of structured tools to improve holistic care for patients with cancer. The Distress Thermometer and Problem Checklist (DT) is commonly used for screening in physical health settings. However, it has not been integrated into the clinical pathway within specialist psycho-oncology services. We used the DT to examine the broad clinical effectiveness of psycho-oncology intervention and to ascertain factors from the DT linked to an improved outcome. We also evaluated patients' satisfaction with their care. We asked 111 adult outpatients referred to York Psycho-Oncology Service to complete the DT at their first appointment. Individuals offered a period of psycho-oncology care re-rated their emotional distress, problems and service satisfaction on the DT at discharge. Median distress scores decreased significantly (from 6 to 4, Wilcoxon's z = -4.83, P psycho-oncology care. It may also provide evidence to support the effectiveness of specialist psycho-oncology interventions. Copyright © 2014 Elsevier Inc. All rights reserved.

Calibration of TOB+ Thermometer's Cards

CERN Document Server

Banitt, Daniel

2014-01-01

Motivation - Under the new upgrade of the CMS detector the working temperature of the trackers had been reduced to -27 Celsius degrees. Though the thermal sensors themselves (Murata and Fenwal thermistors) are effective at these temperatures, the max1542 PLC (programmable logic controller) cards, interpreting the resistance of the thermal sensors into DC counts usable by the DCS (detector control system), are not designed for these temperatures in which the counts exceed their saturation and therefor had to be replaced. In my project I was in charge of handling the emplacement and calibration of the new PLC cards to the TOB (tracker outer barrel) control system.

Design of a temperature measurement and feedback control system based on an improved magnetic nanoparticle thermometer

Science.gov (United States)

Du, Zhongzhou; Sun, Yi; Liu, Jie; Su, Rijian; Yang, Ming; Li, Nana; Gan, Yong; Ye, Na

2018-04-01

Magnetic fluid hyperthermia, as a novel cancer treatment, requires precise temperature control at 315 K-319 K (42 °C-46 °C). However, the traditional temperature measurement method cannot obtain the real-time temperature in vivo, resulting in a lack of temperature feedback during the heating process. In this study, the feasibility of temperature measurement and feedback control using magnetic nanoparticles is proposed and demonstrated. This technique could be applied in hyperthermia. Specifically, the triangular-wave temperature measurement method is improved by reconstructing the original magnetization response of magnetic nanoparticles based on a digital phase-sensitive detection algorithm. The standard deviation of the temperature in the magnetic nanoparticle thermometer is about 0.1256 K. In experiments, the temperature fluctuation of the temperature measurement and feedback control system using magnetic nanoparticles is less than 0.5 K at the expected temperature of 315 K. This shows the feasibility of the temperature measurement method for temperature control. The method provides a new solution for temperature measurement and feedback control in hyperthermia.

Sensors, Volume 4, Thermal Sensors

Science.gov (United States)

Scholz, Jorg; Ricolfi, Teresio

1996-12-01

'Sensors' is the first self-contained series to deal with the whole area of sensors. It describes general aspects, technical and physical fundamentals, construction, function, applications and developments of the various types of sensors. This volume describes the construction and applicational aspects of thermal sensors while presenting a rigorous treatment of the underlying physical principles. It provides a unique overview of the various categories of sensors as well as of specific groups, e.g. temperature sensors (resistance thermometers, thermocouples, and radiation thermometers), noise and acoustic thermometers, heat-flow and mass-flow sensors. Specific facettes of applications are presented by specialists from different fields including process control, automotive technology and cryogenics. This volume is an indispensable reference work and text book for both specialists and newcomers, researchers and developers.

Prevalence and related factors of psychological distress among cancer inpatients using routine Distress Thermometer and Chinese Health Questionnaire screening

Directory of Open Access Journals (Sweden)

Chiou YJ

2016-10-01

Full Text Available Yu-Jie Chiou,1 Nien-Mu Chiu,1 Liang-Jen Wang,2 Shau-Hsuan Li,3 Chun-Yi Lee,1 Ming-Kung Wu,1 Chien-Chih Chen,1 Yi-Shan Wu,1 Yu Lee1 1Department of Psychiatry, 2Department of Child and Adolescent Psychiatry, 3Department of Hematology-Oncology, Kaohsiung Chang Gung Memorial Hospital, Chang Gung University College of Medicine, Kaohsiung, Taiwan, Republic of China Background: Clinical practice guidelines suggest routine screening for distress among cancer patients for immediate early psychiatric care. However, previous studies focusing on routine screening for psychological distress among cancer inpatients in Taiwan are scant. Thus, the aim of this study was to evaluate the prevalence and related factors of psychological distress and mental illness among cancer inpatients in Taiwan. Patients and methods: This study was conducted as a retrospective chart review in a general hospital in southern Taiwan. Cancer inpatients were regularly screened by nursing staff using the Distress Thermometer and the 12-item Chinese Health Questionnaire. Positive screening results on either instrument were followed by a non-commanded referral to psychiatrists for clinical psychiatric diagnosis and treatment. Results: Of the 810 participants in this study, 179 (22.1% were recognized as having psychological distress. Younger age (odds ratio [OR] =1.82, having head and neck cancer (OR =2.43, and having not received chemotherapy (OR =1.58 were significantly related to psychological distress. Among the 56 patients (31.3% with psychological distress who were referred to psychiatrists, the most common mental illness was adjustment disorder (n=22, 39.2%, followed by major depressive disorder (n=13, 23.2%, depressive disorder not otherwise specified (n=6, 10.7%, and anxiety disorder not otherwise specified (n=4, 7.1%. Conclusion: Our study indicated that cancer inpatients with psychological distress were more likely to be younger in age, have head and neck cancer, and have not

The Distress Thermometer assessed in women at risk of developing hereditary breast cancer.

Science.gov (United States)

van Dooren, S; Duivenvoorden, H J; Passchier, J; Bannink, M; Tan, M B M; Oldenmenger, W H; Seynaeve, C; van der Rijt, C C D

2009-10-01

The Distress Thermometer (DT) is a promising instrument to get insight into distress experienced by cancer patients. At our Family Cancer Clinic the DT, including an adapted problem list, was completed by 100 women at increased risk of developing hereditary breast cancer (mean age 45.2 years; SD: 10.5). Additionally, the women filled in either the Hospital Anxiety and Depression Scale as psychological component (n=48) or the somatic subscale of the Symptom Checklist-90 as somatic component (n=50) to identify associations with the DT-score. Further, the women filled in an evaluation form. The median score on the DT was 2 (range: 0-9). With regression analysis adjusted for age, the contribution of mood and somatic complaints, respectively, was investigated. The standardized regression coefficient for anxiety was 0.32 (ns), for depression 0.14 (ns) and for the somatic subscale 0.49 (pdepression was 16%, and for somatic complaints 24%. The differences between the coefficients were not significant. Evaluation forms were returned by 73 women. In 50% of the cases, the physician had discussed the DT/problem list, which was appreciated by the majority of these women (80%). Sixty-two percent of the women would recommend the use of the DT for other patients. The use of the DT/problem list seems promising for the current population, and was appreciated by the majority of the women. As mood and somatic complaints did not differ significantly in explaining the experienced distress, other candidate factors need to be examined.

A four-probe thermal transport measurement method for nanostructures

Energy Technology Data Exchange (ETDEWEB)

Kim, Jaehyun; Ou, Eric; Sellan, Daniel P.; Shi, Li, E-mail: lishi@mail.utexas.edu [Department of Mechanical Engineering, The University of Texas at Austin, Austin, Texas 78712 (United States)

2015-04-15

Several experimental techniques reported in recent years have enabled the measurement of thermal transport properties of nanostructures. However, eliminating the contact thermal resistance error from the measurement results has remained a critical challenge. Here, we report a different four-probe measurement method that can separately obtain both the intrinsic thermal conductance and the contact thermal resistance of individual nanostructures. The measurement device consists of four microfabricated, suspended metal lines that act as resistive heaters and thermometers, across which the nanostructure sample is assembled. The method takes advantage of the variation in the heat flow along the suspended nanostructure and across its contacts to the four suspended heater and thermometer lines, and uses sixteen sets of temperature and heat flow measurements to obtain nine of the thermal resistances in the measurement device and the nanostructure sample, including the intrinsic thermal resistance and the two contact thermal resistances to the middle suspended segment of the nanostructure. Two single crystalline Si nanowires with different cross sections are measured in this work to demonstrate the effectiveness of the method. This four-probe thermal transport measurement method can lead to future discoveries of unique size-dependent thermal transport phenomena in nanostructures and low-dimensional materials, in addition to providing reliable experimental data for calibrating theoretical models.

A four-probe thermal transport measurement method for nanostructures

International Nuclear Information System (INIS)

Kim, Jaehyun; Ou, Eric; Sellan, Daniel P.; Shi, Li

2015-01-01

Several experimental techniques reported in recent years have enabled the measurement of thermal transport properties of nanostructures. However, eliminating the contact thermal resistance error from the measurement results has remained a critical challenge. Here, we report a different four-probe measurement method that can separately obtain both the intrinsic thermal conductance and the contact thermal resistance of individual nanostructures. The measurement device consists of four microfabricated, suspended metal lines that act as resistive heaters and thermometers, across which the nanostructure sample is assembled. The method takes advantage of the variation in the heat flow along the suspended nanostructure and across its contacts to the four suspended heater and thermometer lines, and uses sixteen sets of temperature and heat flow measurements to obtain nine of the thermal resistances in the measurement device and the nanostructure sample, including the intrinsic thermal resistance and the two contact thermal resistances to the middle suspended segment of the nanostructure. Two single crystalline Si nanowires with different cross sections are measured in this work to demonstrate the effectiveness of the method. This four-probe thermal transport measurement method can lead to future discoveries of unique size-dependent thermal transport phenomena in nanostructures and low-dimensional materials, in addition to providing reliable experimental data for calibrating theoretical models

Fiber-optic thermometer application of thermal radiation from rare-earth end-doped SiO2 fiber

International Nuclear Information System (INIS)

Katsumata, Toru; Morita, Kentaro; Komuro, Shuji; Aizawa, Hiroaki

2014-01-01

Visible light thermal radiation from SiO 2 glass doped with Y, La, Ce, Pr, Nd, Eu, Tb, Dy, Ho, Er, Tm, Yb, and Lu were studied for the fiber-optic thermometer application based on the temperature dependence of thermal radiation. Thermal radiations according to Planck's law of radiation are observed from the SiO 2 fibers doped with Y, La, Ce, Pr, Eu, Tb, and Lu at the temperature above 1100 K. Thermal radiations due to f-f transitions of rare-earth ions are observed from the SiO 2 fibers doped with Nd, Dy, Ho, Er, Tm, and Yb at the temperature above 900 K. Peak intensities of thermal radiations from rare-earth doped SiO 2 fibers increase sensitively with temperature. Thermal activation energies of thermal radiations by f-f transitions seen in Nd, Dy, Ho, Er, Tm, and Yb doped SiO 2 fibers are smaller than those from SiO 2 fibers doped with Y, La, Ce, Pr, Eu, Tb, and Lu. Thermal radiation due to highly efficient f-f transitions in Nd, Dy, Ho, Er, Tm, and Yb ions emits more easily than usual thermal radiation process. Thermal radiations from rare-earth doped SiO 2 are potentially applicable for the fiber-optic thermometry above 900 K

Picowatt Resolution Calorimetry for Micro and Nanoscale Energy Transport Studies

Science.gov (United States)

Sadat, Seid H.

Precise quantification of energy transport is key to obtaining insights into a wide range of phenomena across various disciplines including physics, chemistry, biology and engineering. This thesis describes technical advancements into heat-flow calorimetry which enable measurement of energy transport at micro and nanoscales with picowatt resolution. I have developed two types of microfabricated calorimeter devices and demonstrated single digit picowatt resolution at room temperature. Both devices incorporate two distinct features; an active area isolated by a thermal conductance (GTh) of less than 1 microW/K and a high resolution thermometer with temperature resolution (DeltaTres) in the micro kelvin regime. These features enable measurements of heat currents (q) with picowatt resolution (q= Th xDeltaTres). In the first device the active area is suspended via silicon nitride beams with excellent thermal isolation (~600 nW/K) and a bimaterial cantilever (BMC) thermometer with temperature resolution of ~6 microK. Taken together this design enabled calorimetric measurements with 4 pW resolution. In the second device, the BMC thermometry technique is replaced by a high-resolution resistance thermometry scheme. A detailed noise analysis of resistance thermometers, confirmed by experimental data, enabled me to correctly predict the resolution of different measurement schemes and propose techniques to achieve an order of magnitude improvement in the resolution of resistive thermometers. By incorporating resistance thermometers with temperature resolution of ~30 microK, combined with a thermal isolation of ~150 nW/K, I demonstrated an all-electrical calorimeter device with a resolution of ~ 5 pW. Finally, I used these calorimeters to study Near-Field Radiative Heat Transfer (NF-RHT). Using these devices, we studied--for the first time--the effect of film thickness on the NF-RHT between two dielectric surfaces. We showed that even a very thin film (~50 nm) of silicon

Use of SP-100 thermometry technology to improve operation of electric power plants

International Nuclear Information System (INIS)

Shepard, R.L.

1996-01-01

Control of the nuclear power source for the SP-100 electric power supply required a thermometer that would be 1% accurate at temperatures to 1,100 C with no drift and unattended operation for more than 7 years in moderate radiation environment. Johnson noise thermometers had been developed by Oak Ridge National Laboratory originally for nuclear fuel centerline temperature measurements were believed to be able to provide this performance. They were then adapted for use in the SP-100. This Johnson noise technology also has direct application to two problems in the electric power plant: in situ calibration of conventional resistance thermometers installed in steam systems at temperatures up to about 560 C and measurement of combustion chamber temperatures up to bout 1,100 C. Both capacities require measurement of Johnson noise in harsh industrial environments. The final development and transfer of the SP-100 technology to the electric power sector is currently being supported by the Electric Power Research Institute (EPRI)

Cesium heat-pipe thermostat

Energy Technology Data Exchange (ETDEWEB)

Wu, F.; Song, D.; Sheng, K.; Wu, J. [Changcheng Institute of Metrology and Measurement, 100095, Beijing (China); Yi, X. [China National South Aviation industry CO., LTD., 412002, Hunan (China); Yu, Z. [Dalian Jinzhou Institute of Measurement and Testing, 116100, Liaoning (China)

2013-09-11

In this paper the authors report a newly developed Cesium Heat-Pipe Thermostat (Cs HPT) with the operation range of 400 °C to 800 °C. The working medium is cesium (Cs) of 99.98% purity and contains no radioisotope. A Cs filing device is developed which can prevent Cs being in contact with air. The structural material is stainless steel. A 5000 h test has been made to confirm the compatibility between cesium and stainless steel. The Cs HPT has several thermometer wells of 220mm depth with different diameters for different sizes of thermometers. The temperature uniformity of the Cs HPT is 0.06 °C to 0.20 °C. A precise temperature controller is used to ensure the temperature fluctuation within ±0.03 °C. The size of Cs HPT is 380mm×320mm×280mm with foot wheels for easy moving. The thermostat has been successfully used for the calibration of industrial platinum resistance thermometers and thermocouples.

Reviewing the Evidence Base for the Children and Young People Safety Thermometer (CYPST: A Mixed Studies Review

Directory of Open Access Journals (Sweden)

Lydia Aston

2016-01-01

Full Text Available The objective was to identify evidence to support use of specific harms for the development of a children and young people’s safety thermometer (CYPST. We searched PubMed, Web of Knowledge, and Cochrane Library post-1999 for studies in pediatric settings about pain, skin integrity, extravasation injury, and use of pediatric early warning scores (PEWS. Following screening, nine relevant articles were included. Convergent synthesis methods were used drawing on thematic analysis to combine findings from studies using a range of methods (qualitative, quantitative, and mixed methods. A review of PEWS was identified so other studies on this issue were excluded. No relevant studies about extravasation injury were identified. The synthesized results therefore focused on pain and skin integrity. Measurement and perception of pain were complex and not always carried out according to best practice. Skin abrasions were common and mostly associated with device related injuries. The findings demonstrate a need for further work on perceptions of pain and effective communication of concerns about pain between parents and nursing staff. Strategies for reducing device-related injuries warrant further research focusing on prevention. Together with the review of PEWS, these synthesized findings support the inclusion of pain, skin integrity, and PEWS in the CYPST.

Application of radcal gamma thermometer assemblies for coolant monitoring in Ringhals W-PWRs

International Nuclear Information System (INIS)

Smith, R.D.; Romslo, K.; Moen, Oe.

1982-07-01

A study has been carried out investigating how Radcal Gamma Thermometers (RGTs) can be used for coolant inventory and core cooling monitoring in the Ringhals Westinghouse PWRs. The study concludes that two types of RGT rods would be required to come up with a complete solution covering both coolant inventory and core cooling monitoring. Above-core RGT rods will be installed in the guide tubes housing the outlet thermocouples. The Above-Core RGT rod is designed with 8 sensors where 4 are located in the upper head and 4 in the plenum. This rod will give an early warning about loss of coolant or void formation in the space from top of fuel to the reactor lid. A ninth thermocouple in this rod will measure the core outlet temperature as did the thermocouple the RGT rod replaced. The Above-Core RGT rods will give an early warning about approach to Inadequate Core Cooling (ICC) by measuring the collapsed water level inside the thermocouple guide tube. Four such rods are recommended per reactor. In-Core RGT rods are inserted from the seal table. These rods will give the information required for intelligent accident management in case ICC has developed. The signals obtainable from the rods will give direct information about fuel decay heat, core heat transfer conditions, core temperature and core coolant water level. The In-Core RGT rods can be used for local power monitoring during normal operation. Such a system can be shown to be economically motivated from a reactor operation point of view due to increased sensor lifetime, more accurate local power measurements, simpler physics corrections to signals, lower exposure to maintenance personnel. The signal transmission to the control room has been discussed, and ways have been indicated for presenting the information available to the operators. (Authors)

Comparison between tympanic and anal temperature with a clinical infrared ray thermometer in dogs Comparação entre a temperatura timpânica e a temperatura anal usando um termômetro clínico de raio infravermelho em cães

Directory of Open Access Journals (Sweden)

G.G.S. Wiedemann

2006-08-01

Full Text Available A clinical thermometer of infrared rays was used twice to record consecutively the temperature of the tympanic membrane in each ear and in the anus of 53 dogs. Temperatures did not differ significantly between organs, and were strongly correlated. The anal temperature measurement with an infrared thermometer in dogs is feasible and trustworthy, as well as the thermal checking of tympanic temperature.Utilizou-se um termômetro clínico de emissão de raios infravermelhos para medir, duas vezes consecutivas, a temperatura da membrana timpânica de cada ouvido e duas vezes a temperatura no ânus de 53 cães. Não houve diferença entre as temperaturas quanto ao órgão estudado e a correlação entre as temperaturas foi alta. Em cães, a medida da temperatura anal com o termômetro clínico de emissão de raios infravermelhos é rápida e confiável tanto quanto a da temperatura timpânica.

Measuring, processing and evaluation of dynamic signal components of diagnostic systems and instrumentation and control systems at the Temelin NPP

International Nuclear Information System (INIS)

Stulik, P.; Sipek, B.

2005-10-01

The quality of the RVMS measuring chains was examined during an outage of the Temelin-1 reactor unit. This consisted of a defined measurement of the measuring chain output of the ionization chambers of the power zone and thermocouples by the RVMS system, processing of the time series obtained, and evaluation of the spectral parameters within the given frequency band. The results of evaluation were classified for the transfer function values along with their differences and for the phase shift values. The dynamic components of the resistance thermometers on the primary loops of the Temelin-1 and 2 reactor units were measured and the measurements were evaluated. The results in the frequency region, in the form of spectral characteristics for both the hot and cold legs, indicate that the non-invasive determination of the dynamics of the resistance thermometer measuring chains can serve as a promising basic tool for the diagnosis and life monitoring of this important in-service measurement

The workings of a molecular thermometer: the vibrational excitation of carbon tetrachloride by a solvent.

Science.gov (United States)

Graham, Polly B; Matus, Kira J M; Stratt, Richard M

2004-09-15

An intriguing energy-transfer experiment was recently carried out in methanol/carbon tetrachloride solutions. It turned out to be possible to watch vibrational energy accumulating in three of carbon tetrachloride's modes following initial excitation of O-H and C-H stretches in methanol, in effect making those CCl(4) modes "molecular thermometers" reporting on methanol's relaxation. In this paper, we use the example of a CCl(4) molecule dissolved in liquid argon to examine, on a microscopic level, just how this kind of thermal activation occurs in liquid solutions. The fact that even the lowest CCl(4) mode has a relatively high frequency compared to the intermolecular vibrational band of the solvent means that the only solute-solvent dynamics relevant to the vibrational energy transfer will be extraordinarily local, so much so that it is only the force between the instantaneously most prominent Cl and solvent atoms that will significantly contribute to the vibrational friction. We use this observation, within the context of a classical instantaneous-pair Landau-Teller calculation, to show that energy flows into CCl(4) primarily via one component of the nominally degenerate, lowest frequency, E mode and does so fast enough to make CCl(4) an excellent choice for monitoring methanol relaxation. Remarkably, within this theory, the different symmetries and appearances of the different CCl(4) modes have little bearing on how well they take up energy from their surroundings--it is only how high their vibrational frequencies are relative to the solvent intermolecular vibrational band edge that substantially favors one mode over another.

The Distress Thermometer and its validity: a first psychometric study in Indonesian women with breast cancer.

Directory of Open Access Journals (Sweden)

Aulia Iskandarsyah

Full Text Available PURPOSE: This study aims to translate the Distress Thermometer (DT into Indonesian, test its validity in Indonesian women with breast cancer and determine norm scores of the Indonesian DT for clinically relevant distress. METHODS: First, the original version of the DT was translated using a forward and backward translation procedure according to the guidelines. Next, a group of 120 breast cancer patients who were treated at the Outpatient Surgical Oncology Clinic in Hasan Sadikin Hospital in Indonesia completed a standard socio-demographic form, the DT and the Problem List, the Hospital Anxiety and Depression Scale (HADS and the WHO Quality of Life (WHOQOL-BREF. RESULTS: Receiver operating characteristic (ROC curve analyses identified an area under the curve = 0.81 when compared to the HADS cutoff score of 15. A cutoff score of 5 on the DT had the best sensitivity (0.81 and specificity (0.64. Patients who scored above this cutoff reported more problems in the practical, family, emotional, spiritual/religious and physical domains (30 out of 36 problems, p-value<0.05 than patients below the cutoff score. Patients at advanced stages of cancer experienced more emotional and physical problems. Patient's distress level was negatively correlated with overall quality of life, general health and all quality of life domains. CONCLUSIONS: The DT was found to be a valid tool for screening distress in Indonesian breast cancer patients. We recommend using a cutoff score of 5 in this population.

Ion sensors in reactor technology

International Nuclear Information System (INIS)

Strnad, M.; Kott, J.

1977-01-01

A new temperature measurement technique is shown based on the steep phase transformation of some substances accompanied with a marked change in their electric conductivity. A survey is given of the physicochemical properties of some ion crystals and the problems are discussed of interpreting the steep changes in the crystal electric conductivity for ion thermometers. Technological problems are also discussed of ion sensor production for reactor technology applications. The CdI 2 , KIO 3 , K 2 Cr 2 O 7 thermometric compounds were used sealed in the Supermax silicon-aluminium glass or in silica glass with platinum bushings. Changes are described in the hysteresis effects of ion thermometers with CdI 2 , KIO 3 and K 2 Cr 2 O 7 in dependence on neutron irradiation with doses of 1.5x10 18 n.cm -2 , 8.5x10 17 n.cm -2 and 4.5x10 22 n.cm -2 , respectively. The thermometric parameters were compared in the radiation experiments, of ion sensors, Chromel-Alumel thermocouples and platinum resistance thermometers. (B.S.)

Long-term comparison of temperature measurements by the multi-plate shield and Czech-Slovak thermometer screen

Energy Technology Data Exchange (ETDEWEB)

Mozny, Martin; Stepanek, Petr; Hajkova, Lenka; Bares, Daniel [Doksany Observatory, Doksany (Czech Republic). Czech Hydrometeorological Inst.; Trnka, Mirek [Academy of Science of the Czech Republic, Brno (Czech Republic). Global Change Research Centre; Zalud, Zdenek; Semeradova, Daniela [Mendel Univ., Brno (Czech Republic). Agrosystems and Bioclimatology; Koznarova, Vera [Czech Univ. of Life Sciences, Prague (Czech Republic). Dept. of Agroecology and Biometeorology

2012-04-15

Differences between measurements taken with the Czech-Slovak thermometer screen (TS) and the multiplate radiation shield (MRS) should not be neglected. The average difference between the TS and the MRS measurements varied between 0.3 and 2.8 C during suitable weather conditions (wind speed less than 3 m/s, bright and sunny day) throughout the year, during both daytime and nighttime hours. A 10-year time series of comparative measurements in Doksany, Czech Republic, showed that relative to TS, measurements from MRS yielded average and minimum air temperatures that were lower in the winter and higher in the summer. Daily maximum air temperatures were lower for MRS than TS throughout the year. The greatest differences were observed in the maximum air temperatures; only 62 % of all differences between the TS and MRS were less than 0.5 C, and 70 % were less than 1 C. Among minimum air temperatures, 60 % of differences were less than 0.5 C, and 79 % were less than 1 C. In contrast, 74 % of all differences in average daily temperature were less than 0.5 C, and 97 % were less than 1 C. The use of temperature measurements from multiple equipments may negatively affect inference from climate and hydro-meteorological models. Irregular temperature data could be corrected using a simulation of temperature differences (SITEDI) model, which incorporates differences between the MRS and the TS. It is important to consider whether temperature data in the Czech Republic and Slovakia come from the TS or the MRS when analyzing and modeling temperature in Central Europe. (orig.)

49 CFR Appendix H to Part 173 - Method of Testing for Sustained Combustibility

Science.gov (United States)

2010-10-01

... standard manner sustains combustion. 2. Principle of the method A metal block with a concave depression... consisting of a block of aluminum alloy or other corrosion-resistant metal of high thermal conductivity is... is 2.2 mm (see Figure 32.5.2.1); (b) Thermometer, mercury in glass, for horizontal operation, with a...

Validation of Malayalam Version of National Comprehensive Cancer Network Distress Thermometer and its Feasibility in Oncology Patients.

Science.gov (United States)

Biji, M S; Dessai, Sampada; Sindhu, N; Aravind, Sithara; Satheesan, B

2018-01-01

This study was designed to translate and validate the National Comprehensive Cancer Network (NCCN) distress thermometer (DT) in regional language " Malayalam" and to see the feasibility of using it in our patients. (1) To translate and validate the NCCN DT. (2) To study the feasibility of using validated Malayalam translated DT in Malabar Cancer center. This is a single-arm prospective observational study. The study was conducted at author's institution between December 8, 2015, and January 20, 2016 in the Department of Cancer Palliative Medicine. This was a prospective observational study carried out in two phases. In Phase 1, the linguistic validation of the NCCN DT was done. In Phase 2, the feasibility, face validity, and utility of the translated of NCCN DT in accordance with QQ-10 too was done. SPSS version 16 (SPSS Inc. Released 2007. SPSS for Windows, Version 16.0. Chicago, SPSS Inc.) was used for analysis. Ten patients were enrolled in Phase 2. The median age was 51.5 years and 40% of patients were male. All patients had completed at least basic education up to the primary level. The primary site of cancer was heterogeneous. The NCCN DT completion rate was 100%. The face validity, utility, reliability, and feasibility were 100%, 100%, 100%, and 90%, respectively. It can be concluded that the Malayalam validated DT has high face validity, utility, and it is feasible for its use.

Calorimetric cryodetectors for heavy ions

Energy Technology Data Exchange (ETDEWEB)

Egelhof, P; Henning, W; Kienlin, A v; Meier, J; Truebenbacher, V [Gesellschaft fuer Schwerionenforschung mbH, Darmstadt (Germany, F.R.) Mainz Univ. (Germany, F.R.). Inst. fuer Physik; Azgui, F [CDTN, Algiers (Algeria); Shepard, K [Argonne National Lab., IL (USA)

1990-01-01

Status and first test results are reported for a project to develop calorimetric cryodetectors for heavy ions. The special conditions for the detection of energetic heavy ions are discussed. Presently the investigations are focussed on semiconductor bolometers and aluminium-strip superconducting phase-transition thermometers that are cooled with liquid {sup 4}He and operate in the temperature range 1.3-4.2 K. For a germanium bolometer the temperature dependence of the resistance, voltage-current curves, the time response to heating by voltage pulses and the response to ionizing {alpha}-radiation are reported. First tests on phase transition thermometers using thin aluminum strips yield a transition width of {Delta}T=8.6 mK at T{sub c}=1.467 K. (orig.).

Noise thermometry - a new temperature measuring method

International Nuclear Information System (INIS)

Brixy, H.; Hecker, R.; Rittinghaus, K.F.

1975-01-01

The thermal Johnson-Niquist noise is the basis of noise thermometry. This temperature measuring method is, e.g., of interest insofar as the noise thermometer gives absolute values as a primary thermometer and is in principle extensively independent of environmental influences and material properties. The resistance values of the measuring probe are about 10 Ohm to a few kOhm. The demands of electronics are high, the self-noise of the measuring apparatus must be as small as possible; a comparative measuring method is advantageous. 1 to 2,500 K are given as a possible temperature range. An accuracy of 0.1% could be achieved in laboratory measurements. Temperature measurements to be used in operation in a few nuclear reactors are mentioned. (HP/LH) [de

Resident cats in small animal veterinary hospitals carry multi-drug resistant enterococci and are likely involved in cross-contamination of the hospital environment

Directory of Open Access Journals (Sweden)

Anuradha eGhosh

2012-02-01

Full Text Available In the U.S., small animal veterinary hospitals (SAVHs commonly keep resident cats living permanently as pets within their facilities. Previously, multi-drug resistant (MDR enterococci were found as a contaminant of multiple surfaces within such veterinary hospitals, and nosocomial infections are a concern. The objectives of this study were to determine whether resident cats carry MDR enterococci and if they potentially play a role in the contamination of the hospital environment. Enterococcal strains (n=180 were isolated from the feces of six healthy resident cats from different SAVHs. The concentration of enterococci ranged from 1.1 x 105 to 6.0 x 108 CFU g-1 of feces, and the population comprised E. hirae (38.3±18.6%, E. faecium (35.0±14.3%, E. faecalis (23.9±11.0%, and E. avium (2.8±2.2%. Testing of phenotypic resistance to 14 antimicrobial agents revealed multi-drug resistance (≥3 antimicrobials in 48.9% of all enterococcal isolates with most frequent resistance to tetracycline (72.8%, erythromycin (47.8%, and rifampicin (35.6%. Vancomycin resistant E. faecalis (3.9% with vanB not horizontally transferable in in vitro conjugation assays were detected from one cat. Genotyping (pulsed-field gel electrophoresis demonstrated a host-specific clonal population of MDR E. faecalis and E. faecium. Importantly, several feline isolates were genotypically identical or closely related to isolates from surfaces of cage door, thermometer, and stethoscope of the corresponding SAVHs. These data demonstrate that healthy resident cats at SAVHs carry MDR enterococci and likely contribute to contamination of the SAVH environment. Proper disposal and handling of fecal material and restricted movement of resident cats within the ward is recommended.

Accuracy of the Distress Thermometer for home care patients with palliative care needs in Germany.

Science.gov (United States)

Wüller, Johannes; Küttner, Stefanie; Foldenauer, Ann Christina; Rolke, Roman; Pastrana, Tania

2017-06-01

Our aim was to examine the accuracy of the German version of the Distress Thermometer (DT) compared with the Hospital Anxiety and Depression Scale (HADS) in patients with palliative care needs living at home. Ours was a 15-month cross-sectional study beginning in September of 2013 in Germany with consecutive patients cared for by a palliative home care service. The survey was implemented during the initial visit by a home care team. Patients were excluded if they were under 18 years of age, mentally or physically unable to complete the assessment questionnaires as judged by their healthcare worker, or unable to understand the German language. During the first encounter, the DT and HADS were applied, and sociodemographic and medical data were collected. A total of 89 persons completed both the HADS and DT questionnaires (response rate = 59.7%; mean age = 67 years; female = 55.1%; married = 65.2%; living home with relatives = 73.0%; oncological condition = 92.1%; Karnofsky Performance Scale [KPS] score: 0-40 = 30.3%, 50-70 = 57.3%, >80 = 6.7%). The mean DT score was 6.3 (±2.3), with 84.3% of participants scoring above the DT cutoff (≥4). The mean HADStotal score was 17.9 (±7.8), where 64% of participants had a total HADS score (HADStotal) ≥15, 51.7% reported anxiety (HADSanxiety ≥ 8), and 73% reported depression (HADSdepression ≥ 8). Using the HADS as a gold standard, a DT cutoff score ≥5 was optimal for identifying severe distress in patients with palliative care needs, with a sensitivity of 93.0%, a specificity of 34.4%, a positive predictive value (PPV) of 73.3%, and likelihood ratios LR+ = 1.42 (home with palliative care needs in order to offer adequate support.

Thermal limits validation of gamma thermometer power adaption in CFE Laguna Verde 2 reactor core

Energy Technology Data Exchange (ETDEWEB)

Cuevas V, G.; Banfield, J. [GE-Hitachi Nuclear Energy Americas LLC, Global Nuclear Fuel, Americas LLC, 3901 Castle Hayne Road, Wilmingtonm, North Carolina (United States); Avila N, A., E-mail: Gabriel.Cuevas-Vivas@ge.com [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Carretera Cardel-Nautla Km 42.5, Alto Lucero, Veracruz (Mexico)

2016-09-15

This paper presents the status of GEH work on Gamma Thermometer (GT) validation using the signals of the instruments installed in the Laguna Verde Unit 2 reactor core. The long-standing technical collaboration between Comision Federal de Electricidad (CFE), Global Nuclear Fuel - Americas LLC (GNF) and GE-Hitachi Nuclear Energy Americas LLC (GEH) is moving forward with solid steps to a final implementation of GTs in a nuclear reactor core. Each GT is integrated into a slightly modified Local Power Range Monitor (LPRM) assembly. Six instrumentation strings are equipped with two gamma field detectors for a total of twenty-four bundles whose calculated powers are adapted to the instrumentation readings in addition to their use as calibration instruments for LPRMs. Since November 2007, the six GT instrumentation strings have been operable with almost no degradation by the strong neutron and gamma fluxes in the Laguna Verde Unit 2 reactor core. In this paper, the thermal limits, Critical Power Ratio (CPR) and maximum Linear Heat Generation Rate (LHGR), of bundles directly monitored by either Traverse In-core Probes (TIPs) or GTs are used to establish validation results that confirm the viability of TIP system replacement with automatic fixed in-core probes (AFIPs, GTs, in a Boiling Water Reactor. The new GNF steady-state reactor core simulator AETNA02 is used to obtain power and exposure distribution. Using this code with an updated methodology for GT power adaption, a reduced value of the GT interpolation uncertainty is obtained that is fed into the LHGR calculation. This new method achieves margin recovery for the adapted thermal limits for use in the Economic Simplified Boiling Water Reactor (ESBWR) or any other BWR in the future that employs a GT based AFIP system for local power measurements. (Author)

Thermal limits validation of gamma thermometer power adaption in CFE Laguna Verde 2 reactor core

International Nuclear Information System (INIS)

Cuevas V, G.; Banfield, J.; Avila N, A.

2016-09-01

This paper presents the status of GEH work on Gamma Thermometer (GT) validation using the signals of the instruments installed in the Laguna Verde Unit 2 reactor core. The long-standing technical collaboration between Comision Federal de Electricidad (CFE), Global Nuclear Fuel - Americas LLC (GNF) and GE-Hitachi Nuclear Energy Americas LLC (GEH) is moving forward with solid steps to a final implementation of GTs in a nuclear reactor core. Each GT is integrated into a slightly modified Local Power Range Monitor (LPRM) assembly. Six instrumentation strings are equipped with two gamma field detectors for a total of twenty-four bundles whose calculated powers are adapted to the instrumentation readings in addition to their use as calibration instruments for LPRMs. Since November 2007, the six GT instrumentation strings have been operable with almost no degradation by the strong neutron and gamma fluxes in the Laguna Verde Unit 2 reactor core. In this paper, the thermal limits, Critical Power Ratio (CPR) and maximum Linear Heat Generation Rate (LHGR), of bundles directly monitored by either Traverse In-core Probes (TIPs) or GTs are used to establish validation results that confirm the viability of TIP system replacement with automatic fixed in-core probes (AFIPs, GTs, in a Boiling Water Reactor. The new GNF steady-state reactor core simulator AETNA02 is used to obtain power and exposure distribution. Using this code with an updated methodology for GT power adaption, a reduced value of the GT interpolation uncertainty is obtained that is fed into the LHGR calculation. This new method achieves margin recovery for the adapted thermal limits for use in the Economic Simplified Boiling Water Reactor (ESBWR) or any other BWR in the future that employs a GT based AFIP system for local power measurements. (Author)

Patients' and clinicians' experiences of holistic needs assessment using a cancer distress thermometer and problem list: A qualitative study.

Science.gov (United States)

Biddle, Lucy; Paramasivan, Sangeetha; Harris, Susan; Campbell, Rona; Brennan, James; Hollingworth, William

2016-08-01

Psychosocial needs assessment is recommended for patients undergoing cancer treatment, but trials of effectiveness of assessment tools provide mixed results. This qualitative study aimed to understand how such tools are experienced by patients and clinicians in order to optimise use in the future. Qualitative interviews were used in a mixed-methods sequential design following a randomised controlled trial of needs assessment using the Distress Thermometer and Problem List (DT&PL), and explored patients' and clinicians' evaluations of the needs assessment process. Benefits of needs assessment using the DT&PL included the potential to detect hidden distress, allow opportunity for distress to be discussed, and to deliver outcomes to address problems. However, effectiveness and patient willingness to report all forms of distress could be hindered by: clinicians feeling ill-equipped to deal with 'non-physical' distress and patients questioning their appropriateness to do so; time constraints; insufficient support services and referral guidelines; inappropriate timing; and lack of follow-up. The benefits of a holistic needs assessment cannot be realised without matching time and frequency of administration to the dynamic nature of distress during cancer, and making changes to the context of delivery - for instance, providing protected time, increasing referral options and clinician training. Significant investment is needed to optimise potential benefits for patients. Copyright © 2016 Elsevier Ltd. All rights reserved.

Laboratory calibration of the calcium carbonate clumped isotope thermometer in the 25-250 °C temperature range

Science.gov (United States)

Kluge, Tobias; John, Cédric M.; Jourdan, Anne-Lise; Davis, Simon; Crawshaw, John

2015-05-01

Many fields of Earth sciences benefit from the knowledge of mineral formation temperatures. For example, carbonates are extensively used for reconstruction of the Earth's past climatic variations by determining ocean, lake, and soil paleotemperatures. Furthermore, diagenetic minerals and their formation or alteration temperature may provide information about the burial history of important geological units and can have practical applications, for instance, for reconstructing the geochemical and thermal histories of hydrocarbon reservoirs. Carbonate clumped isotope thermometry is a relatively new technique that can provide the formation temperature of carbonate minerals without requiring a priori knowledge of the isotopic composition of the initial solution. It is based on the temperature-dependent abundance of the rare 13C-18O bonds in carbonate minerals, specified as a Δ47 value. The clumped isotope thermometer has been calibrated experimentally from 1 °C to 70 °C. However, higher temperatures that are relevant to geological processes have so far not been directly calibrated in the laboratory. In order to close this calibration gap and to provide a robust basis for the application of clumped isotopes to high-temperature geological processes we precipitated CaCO3 (mainly calcite) in the laboratory between 23 and 250 °C. We used two different precipitation techniques: first, minerals were precipitated from a CaCO3 supersaturated solution at atmospheric pressure (23-91 °C), and, second, from a solution resulting from the mixing of CaCl2 and NaHCO3 in a pressurized reaction vessel at a pressure of up to 80 bar (25-250 °C).

Validation of malayalam version of national comprehensive cancer network distress thermometer and its feasibility in oncology patients

Directory of Open Access Journals (Sweden)

M S Biji

2018-01-01

Full Text Available Context: This study was designed to translate and validate the National Comprehensive Cancer Network (NCCN distress thermometer (DT in regional language " Malayalam" and to see the feasibility of using it in our patients. Aims: (1 To translate and validate the NCCN DT. (2 To study the feasibility of using validated Malayalam translated DT in Malabar Cancer center. Settings and Design: This is a single-arm prospective observational study. The study was conducted at author's institution between December 8, 2015, and January 20, 2016 in the Department of Cancer Palliative Medicine. Materials and Methods: This was a prospective observational study carried out in two phases. In Phase 1, the linguistic validation of the NCCN DT was done. In Phase 2, the feasibility, face validity, and utility of the translated of NCCN DT in accordance with QQ-10 too was done. Statistical Analysis Used: SPSS version 16 (SPSS Inc. Released 2007. SPSS for Windows, Version 16.0. Chicago, SPSS Inc. was used for analysis. Results: Ten patients were enrolled in Phase 2. The median age was 51.5 years and 40% of patients were male. All patients had completed at least basic education up to the primary level. The primary site of cancer was heterogeneous. The NCCN DT completion rate was 100%. The face validity, utility, reliability, and feasibility were 100%, 100%, 100%, and 90%, respectively. Conclusion: It can be concluded that the Malayalam validated DT has high face validity, utility, and it is feasible for its use.

How Hot are Your Ions Really? A Threshold Collision-Induced Dissociation Study of Substituted Benzylpyridinium "Thermometer" Ions

Science.gov (United States)

Carpenter, John E.; McNary, Christopher P.; Furin, April; Sweeney, Andrew F.; Armentrout, P. B.

2017-09-01

The first absolute experimental bond dissociation energies (BDEs) for the main heterolytic bond cleavages of four benzylpyridinium "thermometer" ions are measured using threshold collision-induced dissociation in a guided ion beam tandem mass spectrometer. In this experiment, substituted benzylpyridinium ions are introduced into the apparatus using an electrospray ionization source, thermalized, and collided with Xe at varied kinetic energies to determine absolute cross-sections for these reactions. Various effects are accounted for, including kinetic shifts, multiple collisions, and internal and kinetic energy distributions. These experimentally measured 0 K BDEs are compared with computationally predicted values at the B3LYP-GD3BJ, M06-GD3, and MP2(full) levels of theory with a 6-311+G(2d,2p) basis set using vibrational frequencies and geometries determined at the B3LYP/6-311+G(d,p) level. Additional dissociation pathways are observed for nitrobenzylpyridinium experimentally and investigated using these same levels of theory. Experimental BDEs are also compared against values in the literature at the AM1, HF, B3LYP, B3P86, and CCSD(T) levels of theory. Of the calculated values obtained in this work, the MP2(full) level of theory with counterpoise corrections best reproduces the experimental results, as do the similar literature CCSD(T) values. Lastly, the survival yield method is used to determine the characteristic temperature (Tchar) of the electrospray source prior to the thermalization region and to confirm efficient thermalization. [Figure not available: see fulltext.

Homemade thermometry instruments in the field.

Science.gov (United States)

Pasquier, Mathieu; Rousson, Valentin; Zen Ruffinen, Grégoire; Hugli, Olivier

2012-03-01

Esophageal temperature is the gold standard for in-the-field temperature monitoring in hypothermic victims with cardiac arrest. For practical reasons, some mountain rescue teams use homemade esophageal thermometers to measure esophageal temperature; these consist of nonmedical inside/outside temperature monitoring instruments that have been modified to allow for esophageal insertion. We planned a study to determine the accuracy of such thermometers. Two of the same model of digital cabled indoor/outdoor thermometer were modified and tested in comparison with a reference thermometer. The thermometers were tested in a water bath at different temperatures between 10°C and 35.2°C. Three hundred measurements were taken with each thermometer. Our experimental study showed that both homemade thermometers provided a good correlation and a clinically acceptable agreement in comparison with the reference thermometer. Measurements were within 0.5°C in comparison with the reference thermometer 97.5% of the time. The homemade thermometers performed well in vitro, in comparison with a reference thermometer. However, because these devices in their original form are not designed for clinical use, their use should be restricted to situations when the use of a conventional esophageal thermometer is impossible. Copyright © 2012 Wilderness Medical Society. Published by Elsevier Inc. All rights reserved.

Screening young adult cancer survivors for distress with the Distress Thermometer: Comparisons with a structured clinical diagnostic interview.

Science.gov (United States)

Recklitis, Christopher J; Blackmon, Jaime E; Chang, Grace

2016-01-15

The validity of the Distress Thermometer (DT) as a screen for psychological distress in young adult cancer survivors was assessed by comparing it with the results of a psychiatric diagnostic interview, the Structured Clinical Interview for the Diagnostic and Statistical Manual of Mental Disorders, 4th Edition (DSM-IV) (SCID), to evaluate the accuracy of the DT and identify optimal cutoff scores for this population. A total of 247 survivors aged 18 to 40 years completed the DT and SCID. Based on the SCID, participants were classified as having: 1) ≥ 1 SCID diagnoses; 2) significant symptoms, but no SCID diagnosis; or 3) no significant SCID symptoms. Receiver operating characteristic analyses determined the sensitivity and specificity of all possible DT cutoff scores for detecting survivors with a SCID diagnosis, and subsequently for survivors with significant SCID symptoms or a SCID diagnosis. The recommended DT cutoff score of ≥5 failed to identify 31.81% of survivors with a SCID diagnosis (sensitivity of 68.18% and specificity of 78.33%), and 32.81% of survivors with either significant SCID symptoms or a SCID diagnosis. No alternative DT cutoff score met the criteria for acceptable sensitivity (≥85%) and specificity (≥75%). The DT does not reliably identify young adult cancer survivors with psychiatric problems identified by a "gold standard" structured psychiatric interview. Therefore, the DT should not be used as a stand-alone psychological screen in this population. Cancer 2016;122:296-303. © 2015 American Cancer Society. © 2015 American Cancer Society.

A High-Emissivity Blackbody with Large Aperture for Radiometric Calibration at Low-Temperature

Science.gov (United States)

Ko, Hsin-Yi; Wen, Bor-Jiunn; Tsa, Shu-Fei; Li, Guo-Wei

2009-02-01

A newly designed high-emissivity cylindrical blackbody source with a large diameter aperture (54 mm), an internal triangular-grooved surface, and concentric grooves on the bottom surface was immersed in a temperature-controlled, stirred-liquid bath. The stirred-liquid bath can be stabilized to better than 0.05°C at temperatures between 30 °C and 70 °C, with traceability to the ITS-90 through a platinum resistance thermometer (PRT) calibrated at the fixed points of indium, gallium, and the water triple point. The temperature uniformity of the blackbody from the bottom to the front of the cavity is better than 0.05 % of the operating temperature (in °C). The heat loss of the cavity is less than 0.03 % of the operating temperature as determined with a radiation thermometer by removing an insulating lid without the gas purge operating. Optical ray tracing with a Monte Carlo method (STEEP 3) indicated that the effective emissivity of this blackbody cavity is very close to unity. The size-of-source effect (SSE) of the radiation thermometer and the effective emissivity of the blackbody were considered in evaluating the uncertainty of the blackbody. The blackbody uncertainty budget and performance are described in this paper.

A new garnet-orthopyroxene thermometer developed: method, results and applications

Science.gov (United States)

Olivotos, Spyros-Christos; Kostopoulos, Dimitrios

2014-05-01

The Fe-Mg exchange reaction between garnet and orthopyroxene is a robust geothermometer that has extensively been used to retrieve metamorphic temperatures from granulitic and peridotitic/pyroxenitic lithologies with important implications on the thermal state of the continental lithosphere. More than 800 experimental mineral pairs from both simple and complex systems were gleaned from the literature covering the P-T range 0.5-15 GPa / 800-1800°C. Grt was treated as a senary (Py, Alm, Grs, Sps, Kno and Uv), whereas Opx as a septenary (En, Fs, Di, Hd, FeTs, MgTs and MgCrTs) solid solution. For Opx, Al in the M1 site was calculated following Carswell (1991) and Fe/Mg equipartitioning between sites was assumed. A mixing on sites model was employed to calculate mole fractions of components for both minerals. With regard to the excess free energy of solution and activity coefficients the formalism of Mukhopadhyay et al. (1993) was adopted treating both minerals as symmetric regular solutions. Calibration was achieved in multiple steps; in each step ΔS was allowed to vary until the standard deviation of the differences between experimental and calculated temperature for all experiments was minimised. The experiment with the largest absolute relative deviation in temperature was then eliminated and the process was repeated. The new thermometer reproduces the experimental data to within 50°C and is independent of P-T-X variations within the bounds of the calibrant data set. Application of our new calibration to metamorphosed crustal and mantle rocks that occur both as massifs and xenoliths in volcanics suggested the following results. Granulite terranes have recorded differences in temperature between peak and re-equilibration conditions in the range 100-340°C, primarily depending on the mechanism and rate of exhumation. Several provinces retain memory of discrete cooling pulses (e.g. Palni Hills, South Harris, Adirondacks, E. Antarctic Belt, Aldan Shield) whereas

Determination of mean molecular weights in organic reactor coolants. III. Differential cryoscopy with thermoelectric thermometer; Determinacion de masas moleculares medias en refrigerantes nucleares organicos. III-Crioscopia diferencial con termometro termoelectrico

Energy Technology Data Exchange (ETDEWEB)

Becerro, E; Carreira, M

1968-07-01

The solubility problems raised by some components of the polymeric residue of irradiated polyphenolic coolants, which make it necessary to operate with very small samples, have been solved by means of a differential cryoscopic technique using a thermoelectric thermometer (thermal) as sensitive element. The method is based on the direct measurement of the difference between the freezing points of the investigated solution and of a reference solution whose concentration may be changed at will. The change of {delta} V (mV) versus c(molal) is linear, the equivalent point being determined either analytically or graphically depending on the required accuracy. The method has been tested by measurements on pure polyphenyls, using diphenyl ether as solvent. It has been also applied to the main prospective coolants for the DON reactor. Working with 10{sup 2} molal solutions the accuracy is better than {+-} 2 per cent. (Author) 2 refs.

Error analysis of thermocouple measurements in the Radiant Heat Facility

International Nuclear Information System (INIS)

Nakos, J.T.; Strait, B.G.

1980-12-01

The measurement most frequently made in the Radiant Heat Facility is temperature, and the transducer which is used almost exclusively is the thermocouple. Other methods, such as resistance thermometers and thermistors, are used but very rarely. Since a majority of the information gathered at Radiant Heat is from thermocouples, a reasonable measure of the quality of the measurements made at the facility is the accuracy of the thermocouple temperature data

Thermometry in 3He

International Nuclear Information System (INIS)

Richardson, R.C.

1977-01-01

Some of the methods used in measuring the temperatures of the transitions in 3 He are reviewed. Although noise thermometers, γ-ray anisotropy thermometers and even Pt NMR thermometers are satisfactory for furnishing temperature standards, they are not satisfactory secondary thermometers. The susceptibility of CMN and various 3 He properties make more precise and quicker thermometric indications. (Auth.)

Gamma ray thermometrical facility for nuclear reactor

International Nuclear Information System (INIS)

Smith, R.D.; Regazzoni, Pierre.

1981-01-01

This invention concerns a gamma ray thermometer for nuclear reactors, fitted with a thermal bridge for use as a centring device. In accordance with the invention, an elastic device fills all the annular space between the gamma thermometer and the orifice through which the thermometer is introduced. This elastic device has the two-fold role of providing a thermal bridge at the gamma thermometer location suitable as a heat well, and of acting as a device for centring the thermometer in the orifice into which it has been introduced [fr

Performance of resistive microcalorimeters and bolometers

International Nuclear Information System (INIS)

Galeazzi, M.

2004-01-01

Despite the impressive results achieved by microcalorimeters and bolometers, their performance is still significantly worse than that predicted by Mather's ideal model (Appl. Opt. 21 (1982) 1125). The difference is due both to non-ideal effects and to excess noise of unknown origin. The non-ideal effects have been recently quantified and include hot-electron effect, absorber decoupling, thermometer non-ohmic behavior, and all related extra noise sources. The excess noise affects primarily Transition Edge Sensors (TES) and is currently under experimental and theoretical investigation. This paper reviews the origin of non-ideal effects in microcalorimeters and bolometers and their effect on energy resolution and noise equivalent power. It also reviews the results on the characterization and suppression of the excess noise in TES, and the recent theoretical investigations to explain its origin in relation to fundamental physics in superconductors

Rancang Bangun Alat Ukur Kelajuan Udara Tipe Thermal Terintegrasi Termometer Udara Berbasis Sensor LM35 dan PT100

Directory of Open Access Journals (Sweden)

Laila Katriani

2017-11-01

INTEGRATED WITH AIR THERMOMETER USING  LM35 SENSOR AND PT100 SENSOR This research aimed to design a thermal type anemometer integrated with air thermometer using Lm35 sensor and PT100 sensor. The study began in Mei until Oktober 2016. The study was conducted at the Laboratory of Electronics and Instrumentation, Department of Physics Education, State University of Yogyakarta. The design of the thermal type anemometer consists of two stages, namely, the design of the hardware and software design. Hardware design consists of a sensor system design (LM35 and PT100,  LM317 design, system design for data processing and display. Software design using C language. Based on the results of tests that had been done, shows that the sensor output LM35, whic is voltage is proportional to temperature changes, which had a sensitivity of 0.009 volts / ºC and initial output voltage of the sensor when the temperature reach 0 °C is 0,041 volts. PT100 sensor output, which is resistance is proportional to temperature changes, which had sensitivity of 0.391 Ω/oC and initial output resistance of the sensor when temperature reach 28 °C is 100,8 Ω. Error percent of thermal-type air speed measuring instrument testing is 4%.

NIM gas controlled sodium heat pipe

Science.gov (United States)

Yan, X.; Zhang, J. T.; Merlone, A.; Duan, Y.; Wang, W.

2013-09-01

Gas controlled heat pipes (GCHPs) provide a uniform, stable and reproducible temperature zone to calibrate thermometers and thermocouples, and to realize defining fixed points using a calorimetric method. Therefore, to perform such investigations, a GCHP furnace using sodium as its working fluid was constructed at the National Institute of Metrology (NIM), China. Also, investigations into the thermal characteristics of the NIM gas controlled sodium heat pipe were carried out. The temperature stability over 5 hours was better than ±0.25 mK while controlling the pressure at 111250 Pa. The temperature uniformity within 14 cm from the bottom of the thermometer well was within 0.3 mK. While keeping the pressure stable at the same value, 17 temperature determinations were performed over 14 days, obtaining a temperature reproducibility of 1.27 mK. Additionally, the NIM gas controlled sodium heat pipe was compared with the sodium heat pipe produced by INRiM. The temperature in the INRiM sodium heat pipe operating at 111250 Pa was determined, obtaining a difference of 21 mK with respect to the NIM GCHP. This difference was attributed to sodium impurities, pressure controller capabilities and reproducibility, and instabilities of high temperature standard platinum resistance thermometers (HTSPRTs). Further investigations will be carried out on extending the pressure/temperature range and connecting both GCHPs to the same pressure line.

A calorimeter-Faraday cup to measure energy content of ion beams

International Nuclear Information System (INIS)

Luzzi, G.

1984-01-01

A calorimeter-Faraday cup to measure energy content of ion beams is described. It uses an HP quartz thermometer having a 10 -40 C sensitivity; contact potential problems, arising when working with thermocouples, are so avoided. Calibration has been performed with a resistive filament and with an electron beam. The apparatus is profitable if the measured ion beams are constant in time. The measured sensitivity was 10 -40 C/10 -5 W. (author)

Studies of the Superconducting Transition in the Mo/Au-Bilayer Thin Films

Science.gov (United States)

Sadleir, John; Smith, Stephen; Iyomoto, naoko; Bandler, Simon; Chervenak, Jay; Brown, Ari; Brekowsky, Regis; Kilbourne, Caroline; Robinson, Ian

2007-01-01

At NASA Goddard, microcalorimeter arrays using superconducting transition edge sensor thermometers (TESs) are under development for high energy resolution X-ray astrophysics applications. We report on our studies of the superconducting transition in our Mo/Au-bilayer TES films including: low current measurements of the superconducting bilayer's resistance transition versus temperature on pixels with different normal metal absorber attachment designs and measured temperature scaling of the critical current and critical magnetic field.

Comparison of tympanic and rectal temperature in febrile patients.

Science.gov (United States)

Sehgal, Arvind; Dubey, N K; Jyothi, M C; Jain, Shilpa

2002-04-01

To compare tympanic membrane temperature and rectal temperature in febrile pediatric patients. Sixty febrile children were enrolled as continuous enrollment at initial triage. Two readings of ear temperature were taken in each child with Thermoscan infrared thermometer. Rectal temperature was recorded by a digital electronic thermometer. Comparison of both the techniques was done and co-relation co-efficients calculated. Parental preference for both techniques was assessed. It was observed that mean ear temperature was 38.9+/-0.90 C and that for rectal temperature was 38.8+/-0.80 degrees C. The correlation coefficient between the two was 0.994 (p rays emitted from the surface of tympanic membrane. Ear temperatures correlates well with rectal temperatures which have long been considered as "core" temperatures. Parents prefer the technique of ear thermometry which is quick (2 sec), safe and non-invasive and patient resistance for this is also less. A non-invasive, non-mucous device which is accurate over a wide range of temperature could be very useful.

Temperature measurement: Development work on noise thermometry and improvement of conventional thermocouples for applications in nuclear process heat (PNP)

International Nuclear Information System (INIS)

Brixy, H.; Hecker, R.; Oehmen, J.; Barbonus, P.; Hans, R.

1982-06-01

The behaviour was studied of NiCr-Ni sheathed thermocouples (sheath Inconel 600 or Incoloy 800, insulation MgO) in a helium and carbon atmosphere at temperatures of 950-1150 deg. C. All the thermocouples used retained their functional performance. The insulation resistance tended towards a limit value which is dependent on the temperature and quality of the thermocouple. Temperature measurements were loaded with great uncertainty in the temperature range of 950-1150 deg. C. Recalibrations at the temperature of 950 deg. C showed errors of up to 6%. Measuring sensors were developed which consist of a sheathed double thermocouple with a noise resistor positioned between the two hot junctions. Using the noise thermometer it is possible to recalibrate the thermocouple at any time in situ. A helium system with a high temperature experimental area was developed to test the thermocouples and the combined thermocouple-noise thermometer sensors under true experimental conditions

Comparison of Two Potassium-Filled Gas-Controlled Heat Pipes

Science.gov (United States)

Bertiglia, F.; Iacomini, L.; Moro, F.; Merlone, A.

2015-12-01

Calibration by comparison of platinum resistance thermometers and thermocouples requires transfer media capable of providing very good short-term temperature uniformity and temperature stability over a wide temperature range. This paper describes and compares the performance of two potassium-filled gas-controlled heat pipes (GCHP) for operation over the range from 420° C to 900° C. One of the heat pipes has been in operation for more than 10 years having been operated at temperature for thousands of hours, while the other was commissioned in 2010 following recently developed improvements to both the design, assembly, and filling processes. It was found that the two devices, despite differences in age, structure, number of wells, and filling processes, realized the same temperatures within the measurement uncertainty. The results show that the potassium-filled GCHP provides a durable and high-quality transfer medium for performing thermometer calibrations with very low uncertainties, over the difficult high-temperature range from 420° C to 900° C.

La détection infrarouge avec les plans focaux non refroidis : état de l'artUncooled focal plane infrared detectors: the state of the art

Science.gov (United States)

Tissot, Jean-Luc

2003-12-01

The emergence of uncooled detectors has opened new opportunities for IR detection for both military and commercial applications. Development of such devices involves a lot of trade-offs between the different parameters that define the technological stack. These trade-offs explain the number of different architectures that are under worldwide development. The key factor is to find a high sensitivity and low noise thermometer material compatible with silicon technology in order to achieve high thermal isolation in the smallest area as possible. Ferroelectric thermometer based hybrid technology and electrical resistive thermometer based (microbolometer) technology are under development. LETI and ULIS have chosen from the very beginning to develop first a monolithic microbolometer technology fully compatible with commercially available CMOS technology and secondly amorphous silicon based thermometer. This silicon approach has the greatest potential for reducing infrared detector manufacturing cost. After the development of the technology, the transfer to industrial facilities has been performed in a short period of time and the production is now ramping up with ULIS team in new facilities. LETI and ULIS are now working to facilitate the IRFPA integration into equipment in order to address a very large market. Achievement of this goal needs the development of smart sensors with on-chip advanced functions and the decrease of manufacturing cost of IRFPA by decreasing the pixel pitch and simplifying the vacuum package. We present in this paper the technology developed by CEA/LETI and its improvement for being able to designs 384×288 and 160×120 arrays with a pitch of 35 μm. Thermographic application needs high stability infrared detector with a precise determination of the amount of absorbed infrared flux. Hence, infrared detector with internal temperature stabilized shield has been developed and characterized. These results will be presented. To cite this article: J

Some experiments in low-temperature thermometry

International Nuclear Information System (INIS)

Fogle, W.E.

1982-11-01

A powdered cerous magnesium nitrate (CMN) temperature scale has been developed in the 0.016 to 3.8 K region which represents an interpolation between the 3 He/ 4 He (T 62 /T 58 ) vapor pressure scale and absolute temperatures in the millikelvin region as determined with a 60 Co in hcp Co nuclear orientation thermometer (NOT). Both ac and dc susceptibility thermometers were used in these experiments. The ac susceptibility of a 13 mg CMN-oil slurry was measured with a mutual inductance bridge employing a SQUID null detector while the dc susceptibility of a 3 mg slurry was measured with a SQUID/flux transformer combination. To check the internal consistency of the NOT, γ-ray intensities were measured both parallel and perpendicular to the Co crystal c-axis. The independent temperatures determined in this fashion were found to agree to within experimental error. For the CMN thermometers employed in these experiments, the susceptibility was found to obey a Curie-Weiss law with a Weiss constant of Δ = 1.05 +- 0.1 mK. The powdered CMN scale in the 0.05 to 1.0 K region was transferred to two germanium resistance thermometers for use in low-temperature specific heat measurements. The integrity of the scale was checked by examining the temperature dependence of the specific heat of high purity copper in the 0.1 to 1 K region. In more recent experiments in this laboratory, the scale was also checked by a comparison with the National Bureau of Standards cryogenic temperature scale (NBS-CTS-1). The agreement between the two scales in the 99 to 206 mK region was found to be on the order of the stated accuracy of the NBS scale

Notes on instrumentation and control

CERN Document Server

Roy, G J

2013-01-01

Notes on Instrumentation and Control presents topics on pressure (i.e., U-tube manometers and elastic type gauges), temperature (i.e. glass thermometer, bi-metallic strip thermometer, filled system thermometer, vapor pressure thermometer), level, and flow measuring devices. The book describes other miscellaneous instruments, signal transmitting devices, supply and control systems, and monitoring systems. The theory of automatic control and semi-conductor devices are also considered. Marine engineers will find the book useful.

Noise thermometer

Energy Technology Data Exchange (ETDEWEB)

Von Brixy, H. [Forschungszentrum Juelich GmbH (Germany); Kakuta, Tsunemi

1996-03-01

The noise thermometry (NT) is a temperature measuring method by which the absolute temperature measurement can be performed with a very high accuracy and without any influence of ambient environments and of the thermal history of its NT sensor (electric resistor). Hence it is quite suitable for application as a standard thermometry to the in-situ temperature calibration of incore thermocouples. The KFA Juelich had played a pioneering role in the development of NT and applied the results successfully to the AVR for testing its feasibility. In this report, all about the NT including its principle, sensor elements and system configurations are presented together with the experiences in the AVR and the results of investigation to apply it to high temperature measurement. The NT can be adopted as a standard method for incore temperature measurement and in situ temperature calibration in the HTTR. (author). 85 refs.

Kitchen Thermometers

Science.gov (United States)

... or in bird) 165 Eggs and Egg Dishes Eggs Cook until yolk and white are firm Egg dishes 160 Leftovers and Casseroles 165 *These temperatures are recommended for consumer cooking. They are not intended for processing, institutional, or ...

Ionic thermometers

International Nuclear Information System (INIS)

Strnad, M.

1975-01-01

An original method of temperature measurement based on conductivity changes near the phase transition point of ionic compounds and suitable for the range from 200 to 700 0 C according to the thermometric compound used, is given. By choosing between two approaches it is posible to evaluate either a discrete value of temperature or continuous measurement in a range to about 50 0 C below the phase transition point of thermometric compounds. The extreme nonlinearity of conductivity of the chosen group of ionic crystals used as well as the technical applications developed in the laboratories have not previously been published. The aim of the research is the application of this measuring method for temperature indication in nuclear reactors. Preliminary tests in radiation fields in an experimental reactor are yielding a real hope in this direction. (author)

Noise thermometer

International Nuclear Information System (INIS)

Von Brixy, H.; Kakuta, Tsunemi.

1996-03-01

The noise thermometry (NT) is a temperature measuring method by which the absolute temperature measurement can be performed with a very high accuracy and without any influence of ambient environments and of the thermal history of its NT sensor (electric resistor). Hence it is quite suitable for application as a standard thermometry to the in-situ temperature calibration of incore thermocouples. The KFA Juelich had played a pioneering role in the development of NT and applied the results successfully to the AVR for testing its feasibility. In this report, all about the NT including its principle, sensor elements and system configurations are presented together with the experiences in the AVR and the results of investigation to apply it to high temperature measurement. The NT can be adopted as a standard method for incore temperature measurement and in situ temperature calibration in the HTTR. (author). 85 refs

Heat Capacity and Thermal Conductance Measurements of a Superconducting-Normal Mixed State by Detection of Single 3 eV Photons in a Magnetic Penetration Thermometer

Science.gov (United States)

Stevenson, T. R.; Balvin, M. A.; Bandler, S. R.; Denis, K. L.; Lee, S.-J.; Nagler, P. C.; Smith, S. J.

2015-01-01

We report on measurements of the detected signal pulses in a molybdenum-gold Magnetic Penetration Thermometer (MPT) in response to absorption of one or more 3 eV photons. We designed and used this MPT sensor for x-ray microcalorimetry. In this device, the diamagnetic response of a superconducting MoAu bilayer is used to sense temperature changes in response to absorbed photons, and responsivity is enhanced by a Meissner transition in which the magnetic flux penetrating the sensor changes rapidly to minimize free energy in a mixed superconducting normal state. We have previously reported on use of our MPT to study a thermal phonon energy loss to the substrate when absorbing x-rays. We now describe results of extracting heat capacity C and thermal conductance G values from pulse height and decay time of MPT pulses generated by 3 eV photons. The variation in C and G at temperatures near the Meissner transition temperature (set by an internal magnetic bias field) allow us to probe the behavior in superconducting normal mixed state of the condensation energy and the electron cooling power resulting from quasi-particle recombination and phonon emission. The information gained on electron cooling power is also relevant to the operation of other superconducting detectors, such as Microwave Kinetic Inductance Detectors.

Assessment of psychological distress among Asian adolescents and young adults (AYA) cancer patients using the distress thermometer: a prospective, longitudinal study.

Science.gov (United States)

Chan, Alexandre; Poon, Eileen; Goh, Wei Lin; Gan, Yanxiang; Tan, Chia Jie; Yeo, Kelvin; Chua, Annabelle; Chee, Magdalene; Law, Yi Chye; Somasundaram, Nagavalli; Kanesvaran, Ravindran; Ng, Quan Sing; Tham, Chee Kian; Toh, Chee Keong; Lim, Soon Thye; Tao, Miriam; Tang, Tiffany; Quek, Richard; Farid, Mohamad

2018-04-11

Since few studies have investigated whether the Distress Thermometer (DT) in Asian adolescent and young adult (AYA) cancer patients (between 15 and 39 years), we investigated the appropriateness of the DT as a screening tool for psychological symptom burden in these AYA patients and to evaluate AYA patients' distress across a trajectory of three time points longitudinally over a 6-month period. This was a prospective, longitudinal study. Recruited Asian AYA patients were diagnosed with lymphomas, sarcomas, primary brain malignancies, or germ cell tumors. Patients completed the DT, PedsQL Generic Core Scales, and the Rotterdam Symptom Checklist. Data were analyzed using STATA version 15. Approximately half of the patients experienced clinically significant DT distress (distress score ≥ 4) early in their cancer journey with 43.1% patients presenting with distress at time of diagnosis and 47.7% patients 1 month after diagnosis. Among AYA patients > 24 years old, worry (68.3%), insurance/financial issues (61%), treatment decisions (43.9%), work/school issues (41.5%), nervousness (41.5%), and sadness (41.5%) were the top five identified problems. On the other hand, the top five identified problems among AYA ≤ 24 years were worry (54.2%), nervousness (41.7%), bathing/dressing problems (37.5%), work/school issues (33.3%), and fatigue (33.3%). DT scores were significantly associated with certain psychological symptom burden items such as worry (p psychological distress in AYA cancer patients with clinically significant distress being identified in the early phases of the cancer journey.

Development of a low-cost temperature data monitoring. An upgrade for hot box apparatus

Science.gov (United States)

de Rubeis, T.; Nardi, I.; Muttillo, M.

2017-11-01

The monitoring phase has gained a fundamental role in the energy efficiency evaluation of a system. Number and typology of the probes depend on the physical quantity to be monitored, and on the size and complexity of the system. Moreover, a measurement equipment should be designed to allow the employment of probes different for number and measured physical quantities. For this reason, a scalable equipment represents a good way for easily carrying out a system monitoring. Proprietary software and high costs characterize instruments of current use, thus limiting the possibilities to realize customized monitoring. In this paper, a temperature measuring instrument, conceived, designed, and realized for real time applications, is presented. The proposed system is based on digital thermometers and on open-source code. A remarkable feature of the instrument is the possibility of acquiring data from a high and variable number of probes (order of hundred), assuring flexibility of the software, since it can be programmed, and low-cost of the hardware components. The contemporary use of multiple temperature probes suggested to apply this instrument for a hot box apparatus, although the software can be set for recording different physical quantities. A hot box compliant with standard EN ISO 8990 should be equipped with several temperature probes to investigate heat exchanges of a specimen wall and thermal field of the chambers. In this work, preliminary tests have been carried out focusing only on the evaluation of the prototypal system’s performance. The tests were realized by comparing different sensors, such as thermocouples and resistance thermometers, traditionally employed in hot box experiments. A preliminary test was realized imposing a dynamic condition with a thermoelectric Peltier cell. Data obtained by digital thermometers DS18B20, compared with the ones of Pt100 probes, show a good correlation. Based on these encouraging results, a further test was carried out

Temperature distribution model for the semiconductor dew point detector

Science.gov (United States)

Weremczuk, Jerzy; Gniazdowski, Z.; Jachowicz, Ryszard; Lysko, Jan M.

2001-08-01

The simulation results of temperature distribution in the new type silicon dew point detector are presented in this paper. Calculations were done with use of the SMACEF simulation program. Fabricated structures, apart from the impedance detector used to the dew point detection, contained the resistive four terminal thermometer and two heaters. Two detector structures, the first one located on the silicon membrane and the second one placed on the bulk materials were compared in this paper.

Nanocrystalline SiC film thermistors for cryogenic applications

Science.gov (United States)

Mitin, V. F.; Kholevchuk, V. V.; Semenov, A. V.; Kozlovskii, A. A.; Boltovets, N. S.; Krivutsa, V. A.; Slepova, A. S.; Novitskii, S. V.

2018-02-01

We developed a heat-sensitive material based on nanocrystalline SiC films obtained by direct deposition of carbon and silicon ions onto sapphire substrates. These SiC films can be used for resistance thermometers operating in the 2 K-300 K temperature range. Having high heat sensitivity, they are relatively low sensitive to the magnetic field. The designs of the sensors are presented together with a discussion of their thermometric characteristics and sensitivity to magnetic fields.

From dispensing to disposal: the role of student pharmacists in medication disposal and the implementation of a take-back program.

Science.gov (United States)

Gray-Winnett, Misty D; Davis, Courtney S; Yokley, Stephanie G; Franks, Andrea S

2010-01-01

To decrease the amount of pharmaceuticals present in our community's water supply, reduce the accidental and intentional ingestion of pharmaceuticals, and increase awareness of proper medication disposal. Knoxville, TN, from November 2008 to November 2009. Medication and thermometer collection events were held at various community retail establishments. Community officials and students collaborated to plan advertising, implementation, and appropriate medication and thermometer disposal. Event volunteers set up easily accessible tents and tables in high-traffic areas to collect unused medications, mercury thermometers, and recyclable medication bottles. Student pharmacists worked cooperatively with community partners to collect unused medications and exchange thermometers. Pounds of recyclables collected, pounds of medications collected, and number of thermometers exchanged. The events increased community awareness of appropriate medication disposal and pharmacists' roles in safe use of medications. From November 2008 to November 2009, more than 1,100 pounds of unwanted medications were collected through events and the drop box. Additionally, more than 470 pounds of recyclable packaging material was collected and 535 mercury thermometers exchanged. Student pharmacists can partner with community officials and businesses to provide safe and appropriate medication and mercury thermometer disposal.

Progress in Noise Thermometry at 505 K and 693 K Using Quantized Voltage Noise Ratio Spectra

Science.gov (United States)

Tew, W. L.; Benz, S. P.; Dresselhaus, P. D.; Coakley, K. J.; Rogalla, H.; White, D. R.; Labenski, J. R.

2010-09-01

Technical advances and new results in noise thermometry at temperatures near the tin freezing point and the zinc freezing point using a quantized voltage noise source (QVNS) are reported. The temperatures are derived by comparing the power spectral density of QVNS synthesized noise with that of Johnson noise from a known resistance at both 505 K and 693 K. Reference noise is digitally synthesized so that the average power spectra of the QVNS match those of the thermal noise, resulting in ratios of power spectra close to unity in the low-frequency limit. Three-parameter models are used to account for differences in impedance-related time constants in the spectra. Direct comparison of noise temperatures to the International Temperature Scale of 1990 (ITS-90) is achieved in a comparison furnace with standard platinum resistance thermometers. The observed noise temperatures determined by operating the noise thermometer in both absolute and relative modes, and related statistics together with estimated uncertainties are reported. The relative noise thermometry results are combined with results from other thermodynamic determinations at temperatures near the tin freezing point to calculate a value of T - T 90 = +4(18) mK for temperatures near the zinc freezing point. These latest results achieve a lower uncertainty than that of our earlier efforts. The present value of T - T 90 is compared to other published determinations from noise thermometry and other methods.

[Resistance risk, cross-resistance and biochemical resistance mechanism of Laodelphax striatellus to buprofezin].

Science.gov (United States)

Mao, Xu-lian; Liu, Jin; Li, Xu-ke; Chi, Jia-jia; Liu, Yong-jie

2016-01-01

In order to investigate the resistance development law and biochemical resistance mechanism of Laodelphax striatellus to buprofezin, spraying rice seedlings was used to continuously screen resistant strains of L. striatellus and dipping rice seedlings was applied to determine the toxicity and cross-resistance of L. striatellus to insecticides. After 32-generation screening with buprofezin, L. striatellus developed 168.49 folds resistance and its reality heritability (h2) was 0.11. If the killing rate was 80%-90%, L. striatellus was expected to develop 10-fold resistance to buprofezin only after 5 to 6 generations breeding. Because the actual reality heritability of field populations was usually lower than that of the resistant strains, the production of field populations increasing with 10-fold resistance would need much longer time. The results of cross-resistance showed that resistant strain had high level cross-resistance with thiamethoxam and imidacloprid, low level cross-resistance with acetamiprid, and no cross-resistance with pymetrozine and chlorpyrifos. The activity of detoxification enzymes of different strains and the syergism of synergist were measured. The results showed that cytochrome P450 monooxygenase played a major role in the resistance of L. striatellus to buprofezin, the esterase played a minor role and the GSH-S-transferase had no effect. Therefore, L. striatellus would have high risk to develop resistance to buprofezin when used in the field and might be delayed by using pymetrozine and chlorpyrifos.

Comparison of three methods of temperature measurement in hypothermic, euthermic, and hyperthermic dogs.

Science.gov (United States)

Greer, Rebecca J; Cohn, Leah A; Dodam, John R; Wagner-Mann, Colette C; Mann, F A

2007-06-15

To assess the reliability and accuracy of a predictive rectal thermometer, an infrared auricular thermometer designed for veterinary use, and a subcutaneous temperature-sensing microchip for measurement of core body temperature over various temperature conditions in dogs. Prospective study. 8 purpose-bred dogs. A minimum of 7 days prior to study commencement, a subcutaneous temperature-sensing microchip was implanted in 1 of 3 locations (interscapular, lateral aspect of shoulder, or sacral region) in each dog. For comparison with temperatures measured via rectal thermometer, infrared auricular thermometer, and microchip, core body temperature was measured via a thermistor-tipped pulmonary artery (TTPA) catheter. Hypothermia was induced during anesthesia at the time of TTPA catheter placement; on 3 occasions after placement of the catheter, hyperthermia was induced via administration of a low dose of endotoxin. Near-simultaneous duplicate temperature measurements were recorded from the TTPA catheter, the rectal thermometer, auricular thermometer, and subcutaneous microchips during hypothermia, euthermia, and hyperthermia. Reliability (variability) of temperature measurement for each device and agreement between each device measurement and core body temperature were assessed. Variability between duplicate near-simultaneous temperature measurements was greatest for the auricular thermometer and least for the TTPA catheter. Measurements obtained by use of the rectal thermometer were in closest agreement with core body temperature; for all other devices, temperature readings typically underestimated core body temperature. Among the 3 methods of temperature measurement, rectal thermometry provided the most accurate estimation of core body temperature in dogs.

Acceptability of the Distress Thermometer and Problem List to community-based telephone cancer helpline operators, and to cancer patients and carers

Directory of Open Access Journals (Sweden)

Sargeant Hilary

2011-01-01

Full Text Available Abstract Background Cancer can be a distressing experience for cancer patients and carers, impacting on psychological, social, physical and spiritual functioning. However, health professionals often fail to detect distress in their patients due to time constraints and a lack of experience. Also, with the focus on the patient, carer needs are often overlooked. This study investigated the acceptability of brief distress screening with the Distress Thermometer (DT and Problem List (PL to operators of a community-based telephone helpline, as well as to cancer patients and carers calling the service. Methods Operators (n = 18 monitored usage of the DT and PL with callers (cancer patients/carers, >18 years, and English-speaking from September-December 2006 (n = 666. The DT is a single item, 11-point scale to rate level of distress. The associated PL identifies the cause of distress. Results The DT and PL were used on 90% of eligible callers, most providing valid responses. Benefits included having an objective, structured and consistent means for distress screening and triage to supportive care services. Reported challenges included apparent inappropriateness of the tools due to the nature of the call or level of caller distress, the DT numeric scale, and the level of operator training. Conclusions We observed positive outcomes to using the DT and PL, although operators reported some challenges. Overcoming these challenges may improve distress screening particularly by less experienced clinicians, and further development of the PL items and DT scale may assist with administration. The DT and PL allow clinicians to direct/prioritise interventions or referrals, although ongoing training and support is critical in distress screening.

Temperature measurement in practice with resistance thermometers and thermocouples; Temperaturmesspraxis mit Widerstandsthermometern und Thermoelementen

Energy Technology Data Exchange (ETDEWEB)

Irrgang, K.; Michalowsky, L (eds.)

2004-07-01

The book addresses students of science and engineering, engineers and practicians in research and industry who are interested in temperature measurements and thermal processes in the temperature range between a few K and over 3200 K. For the first time ever, temperature sensors are classified on the basis of heat transport and heat transfer to the sensor as related to the technological aspects of sensor stress. This includes physical and materials-related fundamentals, materials selection, sensor design and optimisation, error analysis, as well as the analysis of economically relevant applications of electrical temperature measurement in thermal processes. [German] Dieses Buch wendet sich an Studenten der Natur- und Technikwissenschaften, Ingenieure und Hochschulabsolventen in der Forschung und Industrie, die sich mit Temperaturmessungen und thermischen Prozessen im Temperaturbereich von wenigen Kelvin bis zu ueber 3200 K befassen. Der neue Titel wird sich gegenueber bekannten Standards auf diesem Gebiet dadurch auszeichnen, dass eine Klassifizierung der Temperaturfuehler abhaengig vom Waermetransport und den Waermeuebergaengen zum Sensor in Verbindung mit den technologischen Aspekten zu den konkreten Beanspruchungen der Fuehler in der Anwendung vorgenommen wird. Dieser hohe Anspruch schliesst physikalische und werkstoffwissenschaftliche Grundlagen zur Systemloesung, der Werkstoffauswahl, zur Auslegung und Optimierung des Fuehlerdesigns und der notwendigen Fehlerbetrachtung ebenso ein, wie die Analyse volkswirtschaftlich bedeutsamer Anwendungen der elektrischen Temperaturmesstechnik in thermischen Prozessen. (orig.)

Precise quantization of anomalous Hall effect near zero magnetic field

Energy Technology Data Exchange (ETDEWEB)

Bestwick, A. J. [Stanford Univ., Stanford, CA (United States); SLAC National Accelerator Lab., Menlo Park, CA (United States); Fox, E. J. [Stanford Univ., Stanford, CA (United States); SLAC National Accelerator Lab., Menlo Park, CA (United States); Kou, Xufeng [Univ. of California, Los Angeles, CA (United States); Pan, Lei [Univ. of California, Los Angeles, CA (United States); Wang, Kang L. [Univ. of California, Los Angeles, CA (United States); Goldhaber-Gordon, D. [Stanford Univ., Stanford, CA (United States); SLAC National Accelerator Lab., Menlo Park, CA (United States)

2015-05-04

In this study, we report a nearly ideal quantum anomalous Hall effect in a three-dimensional topological insulator thin film with ferromagnetic doping. Near zero applied magnetic field we measure exact quantization in the Hall resistance to within a part per 10,000 and a longitudinal resistivity under 1 Ω per square, with chiral edge transport explicitly confirmed by nonlocal measurements. Deviations from this behavior are found to be caused by thermally activated carriers, as indicated by an Arrhenius law temperature dependence. Using the deviations as a thermometer, we demonstrate an unexpected magnetocaloric effect and use it to reach near-perfect quantization by cooling the sample below the dilution refrigerator base temperature in a process approximating adiabatic demagnetization refrigeration.

Magnetic disturbance effects in noise thermometry

International Nuclear Information System (INIS)

Fischer, M.

1992-01-01

Due to the very small measurement signals, a compensation process is used, which presupposes undisturbed signals of the measurement resistance and a compensation resistance as necessary conditions. There is a two-channel control for the measurement and compensation circuit, so that parasitic noise voltages from the incoming leads and the electronics can be eliminated by cross-correlation. The sensor which is designed as a combined thermocouple/noise thermometer sensor, permits continuous measurement of temperature by measuring the thermal voltages and the in situ calibration of the thermocouples at all times, which may have considerable drift of the thermal voltages, depending on environmental effects. Leads designed as thermocouples use ferromagnetic materials, in part. (orig./DG) [de

A noise thermometry investigation of the melting point of gallium at the NIM

Science.gov (United States)

Zhang, J. T.; Xue, S.

2006-06-01

This paper describes a study of the melting point of gallium with the new NIM Johnson noise thermometer (JNT). The new thermometer adopts the structure of switching correlator and commutator with the reference resistor maintained at the triple point of water. The electronic system of the new thermometer is basically the same as the current JNT, but the preamplifiers have been improved slightly. This study demonstrates that examining the characteristics of the noise signals in the frequency domain is of critical importance in constructing an improved new thermometer, where a power spectral analysis is found to be critical in establishing appropriate grounding for the new thermometer. The new JNT is tested on measurements of the thermodynamic temperature of the melting point of gallium, which give the thermodynamic temperature of 302.9160 K, with an overall integration time of 190 h and a combined standard uncertainty of 9.4 mK. The uncertainty analysis indicates that a standard combined uncertainty of 3 mK could be achieved with the new thermometer over an integration period of 1750 h.

A resistência olha a resistência

Directory of Open Access Journals (Sweden)

Jorge Ponciano Ribeiro

Full Text Available Resistência é um processo humano que acontece quando a pessoa se encontra sob algum tipo de ameaça. Não é essencialmente um acontecimento psicoterapêutico. Ocorre na terapia não como uma oposição a si mesmo ou ao terapeuta, mas como uma forma de se ajustar a uma nova situação. A resistência, é por natureza, a atualização do instinto de auto-preservação. E o organismo inteligentemente segue a lei da preferência. Resistência é uma forma de contato que não pode ser destruída, mas administrada, porque ela surge como uma defesa da totalidade vivenciada pela pessoa. A Resistência é, às vezes, resistência e awareness mais que ao contato. Ela revela mais o caminho seguido do que oculta a caminhada feita. A resistência é um processo natural, porque o corpo que não resiste, morre, mas falamos em processos de auto-regulação organísmica. Valorizamos mais o que mantêm a resistência funcionando do que à própria resistência. O terapeuta também resiste, ou seja, ele se auto-regula na sua relação com o cliente. Não questionamos a resistência, mas o processo que a mantêm. Trabalhamos com nove mecanismos de defesa, também tradicionalmente, chamados de resistência.

Accuracy of the Approximation Function Deduced from the Fixed 3-Points Calibration Delivered with the Cernox™ Sensor

CERN Document Server

Balle, C; Fortescue-Beck, E; Vauthier, N

2013-01-01

The cernox™ sensor is delivered with a 3-point resistance versus temperature cal-ibration that permits the construction of an individual interpolation table by using the data in the CERN thermometer database. For instance at the 4.2 K point, the individual calibration and the manufacturer data are within +/-0.1 K for 99.39% of a sample population of about 5700 sensors. Preliminary results also indicate that accuracies of 0.1 K and 1 K can be obtained below respectively 5 K and 77 K.

Fixed type incore measuring device

International Nuclear Information System (INIS)

Oda, Naotaka; Ito, Hitoshi; Maeda, Hiroyuki

1998-01-01

The present invention concerns a measuring device using gamma thermometers to be used in a BWR type reactor. An input switch is inserted to the vicinity of a detection signal input portion of a signal cable connecting GT with the detection signal input portion of a fixed type incore measuring device, and a loop resistance measuring means is disposed to the input switch on the side of the GT by way of a measurement switch. Upon measuring loop resistance, the GT measuring circuit is switched from the detection signal input portion to the loop resistance measuring means by a switching operation of the input switch and the measurement switch thereby enabling to confirm the value of the loop resistance. In addition, the lowering of the voltage in the loop resistance is compensated to confirm the accurate measurement values to be used thereby enabling to measure GT detection signals accurately. A diagnosing means for diagnosing the state of GT based on the results of the measurement for the loop resistance is disposed, and the results are reported to an operator. (N.H.)

Measurement of Dynamic Resistance in Resistance Spot Welding

DEFF Research Database (Denmark)

Wu, Pei; Zhang, Wenqi; Bay, Niels

Through years, the dynamic resistance across the electrodes has been used for weld quality estimation and contact resistance measurement. However, the previous methods of determining the dynamic resistance were mostly based on measuring the voltage and current on the secondary side of the transfo......Through years, the dynamic resistance across the electrodes has been used for weld quality estimation and contact resistance measurement. However, the previous methods of determining the dynamic resistance were mostly based on measuring the voltage and current on the secondary side...... of the transformer in resistance welding machines, implying defects from induction noise and interference with the leads connected to the electrodes for measuring the voltage. In this study, the dynamic resistance is determined by measuring the voltage on the primary side and the current on the secondary side...

High temperature measurement by noise thermometry

International Nuclear Information System (INIS)

Decreton, M.C.

1982-06-01

Noise thermometry has received a lot of attention for measurements of temperatures in the high range around 1000-2000 deg. K. For these measurements, laboratory type experiments have been mostly performed. These have shown the interest of the technique when long term stability, high precision and insensibility to external conditions are concerned. This is particularly true for measurements in nuclear reactors where important drifts due to irradiation effects are experienced with other measurement techniques, as thermocouple for instance. Industrial noise thermometer experiments have not been performed extensively up to now. The subject of the present study is the development of a 1800 deg. K noise thermometer for nuclear applications. The measurement method is based on a generalized noise power approach. The rms noise voltage (Vsub(s)) and noise current (Isub(s)) are successively measured on the resistive sensor. The same quantities are also measured on a dummy short circuited probe (Vsub(d) and Isub(d)). The temperature is then deduced from these measured values by the following formula: cTsub(s) = (Vsub(s) 2 - Vsub(d) 2 )(Vsub(s)/Isub(s) - Vsub(d)/Isub(d)) - 1 , where c is a constant and Tsub(s) the absolute temperature of the sensor. This approach has the particular advantage of greatly reducing the sensibility to environmental perturbations on the leads and to the influence of amplifier noise sources. It also eliminates the necessity of resistance measurement and keeps the electronic circuits as simple as possible

A nonintrusive method for measuring the operating temperature of a solenoid-operated valve

International Nuclear Information System (INIS)

Kryter, R.C.

1990-01-01

Experimental data are presented to show that the in-service operating temperature of a solenoid-operated valve (SOV) can be interred simply and nondisruptively by using the copper winding of the solenoid coil as a self-indicating, permanently available resistance thermometer. The principal merits of this approach include (a) there is no need for an add-on temperature sensor, (b) the true temperature of a critical --- and likely the hottest --- part of the SOV (namely, the electrical coil) is measured directly, (c) temperature readout can be provided at any location at which the SOV electrical lead wires are accessible (even though remote from the valve), (d) the SOV need not be disturbed (whether normally energized or deenergized) to measure its temperature in situ, and (e) the method is applicable to all types of SOVs, large and small, ac- and dc-powered. Laboratory tests comparing temperatures measured both by coil resistance and by a conventional thermometer placed in contact with the external surface of the potted solenoid coil indicate that temperature within the coil may be on the order of 40 degree C higher than that measured externally, a fact that is important to life-expectancy calculations made on the basis of Arrhenius theory. Field practicality is illustrated with temperature measurements made using this method on a SOV controlling the flow of refrigerant in a large chilled-water air-conditioning system. 5 refs., 7 figs

Analytical expressions for transition edge sensor excess noise models

International Nuclear Information System (INIS)

Brandt, Daniel; Fraser, George W.

2010-01-01

Transition edge sensors (TESs) are high-sensitivity thermometers used in cryogenic microcalorimeters which exploit the steep gradient in resistivity with temperature during the superconducting phase transition. Practical TES devices tend to exhibit a white noise of uncertain origin, arising inside the device. We discuss two candidate models for this excess noise, phase slip shot noise (PSSN) and percolation noise. We extend the existing PSSN model to include a magnetic field dependence and derive a basic analytical model for percolation noise. We compare the predicted functional forms of the noise current vs. resistivity curves of both models with experimental data and provide a set of equations for both models to facilitate future experimental efforts to clearly identify the source of excess noise.

Induced resistance: an enhancement of basal resistance?

NARCIS (Netherlands)

Vos, M. de; Robben, C.; Pelt, J.A. van; Loon, L.C. van; Pieterse, C.M.J.

2002-01-01

Upon primary pathogen attack, plants activate resistance mechanisms at the site of infection. Besides this so-called basal resistance, plants have also the ability to enhance their defensive capacity against future pathogen attack. There are at least two types of biologically induced resistance.

HIV resistance testing and detected drug resistance in Europe

DEFF Research Database (Denmark)

Schultze, Anna; Phillips, Andrew N; Paredes, Roger

2015-01-01

to Southern Europe. CONCLUSIONS: Despite a concurrent decline in virological failure and testing, drug resistance was commonly detected. This suggests a selective approach to resistance testing. The regional differences identified indicate that policy aiming to minimize the emergence of resistance......OBJECTIVES: To describe regional differences and trends in resistance testing among individuals experiencing virological failure and the prevalence of detected resistance among those individuals who had a genotypic resistance test done following virological failure. DESIGN: Multinational cohort...... study. METHODS: Individuals in EuroSIDA with virological failure (>1 RNA measurement >500 on ART after >6 months on ART) after 1997 were included. Adjusted odds ratios (aORs) for resistance testing following virological failure and aORs for the detection of resistance among those who had a test were...

Inheritance of Cry1F resistance, cross-resistance and frequency of resistant alleles in Spodoptera frugiperda (Lepidoptera: Noctuidae).

Science.gov (United States)

Vélez, A M; Spencer, T A; Alves, A P; Moellenbeck, D; Meagher, R L; Chirakkal, H; Siegfried, B D

2013-12-01

Transgenic maize, Zea maize L., expressing the Cry1F protein from Bacillus thuringiensis has been registered for Spodoptera frugiperda (J. E. Smith) control since 2003. Unexpected damage to Cry1F maize was reported in 2006 in Puerto Rico and Cry1F resistance in S. frugiperda was documented. The inheritance of Cry1F resistance was characterized in a S. frugiperda resistant strain originating from Puerto Rico, which displayed >289-fold resistance to purified Cry1F. Concentration-response bioassays of reciprocal crosses of resistant and susceptible parental populations indicated that resistance is recessive and autosomal. Bioassays of the backcross of the F1 generation crossed with the resistant parental strain suggest that a single locus is responsible for resistance. In addition, cross-resistance to Cry1Aa, Cry1Ab, Cry1Ac, Cry1Ba, Cry2Aa and Vip3Aa was assessed in the Cry1F-resistant strain. There was no significant cross-resistance to Cry1Aa, Cry1Ba and Cry2Aa, although only limited effects were observed in the susceptible strain. Vip3Aa was highly effective against susceptible and resistant insects indicating no cross-resistance with Cry1F. In contrast, low levels of cross-resistance were observed for both Cry1Ab and Cry1Ac. Because the resistance is recessive and conferred by a single locus, an F1 screening assay was used to measure the frequency of Cry1F-resistant alleles from populations of Florida and Texas in 2010 and 2011. A total frequency of resistant alleles of 0.13 and 0.02 was found for Florida and Texas populations, respectively, indicating resistant alleles could be found in US populations, although there have been no reports of reduced efficacy of Cry1F-expressing plants.

submitter Experimental temperature measurements for the energy amplifier test

CERN Document Server

Calero, J; Gallego, E; Gálvez, J; García Tabares, L; González, E; Jaren, J; López, C; Lorente, A; Martínez Val, J M; Oropesa, J; Rubbia, C; Rubio, J A; Saldana, F; Tamarit, J; Vieira, S

1996-01-01

A uranium thermometer has been designed and built in order to make local power measurements in the First Energy Amplifier Test (FEAT). Due to the experimental conditions power measurements of tens to hundreds of nW were required, implying a sensitivity in the temperature change measurements of the order of 1 mK. A uranium thermometer accurate enough to match that sensitivity has been built. The thermometer is able to determine the absolute energetic gain obtained in a tiny subcritical uranium assembly exposed to a proton beam of kinetic energies between 600 MeV and 2.75 GeV. In addition, the thermometer measurements have provided information about the spatial power distribution and the shape of the neutron spallation cascade.

Adriamycin resistance, heat resistance and radiation response in Chinese hamster fibroblasts

International Nuclear Information System (INIS)

Wallner, K.; Li, G.

1985-01-01

Previous investigators have demonstrated synergistic interaction between hyperthermia and radiation or Adriamycin (ADR), using cell lines that are sensitive to heat or ADR alone. The authors investigated the effect of heat, radiation or ADR on Chinese hamster fibroblasts (HA-1), their heat resistant variants and their ADR resistant variants. Heat for ADR resistance did not confer cross resistance to radiation. Cells resistant to heat did show cross resistance to ADR. While cells selected for ADR resistance were not cross resistant to heat, they did not exhibit drug potentiation by hyperthermia, characteristic of ADR sensitive cells. Cytofluorometric measurement showed decreased ADR uptake in both heat and ADR resistant cells. The possibility of cross resistance between heat and ADR should be considered when designing combined modality trials

Outwitting the series resistance in scanning spreading resistance microscopy

International Nuclear Information System (INIS)

Schulze, A.; Cao, R.; Eyben, P.; Hantschel, T.; Vandervorst, W.

2016-01-01

The performance of nanoelectronics devices critically depends on the distribution of active dopants inside these structures. For this reason, dopant profiling has been defined as one of the major metrology challenges by the international technology roadmap of semiconductors. Scanning spreading resistance microscopy (SSRM) has evolved as one of the most viable approaches over the last decade due to its excellent spatial resolution, sensitivity and quantification accuracy. However, in case of advanced device architectures like fins and nanowires a proper measurement of the spreading resistance is often hampered by the increasing impact of parasitic series resistances (e.g. bulk series resistance) arising from the confined nature of the aforementioned structures. In order to overcome this limitation we report in this paper the development and implementation of a novel SSRM mode (fast Fourier transform-SSRM: FFT-SSRM) which essentially decouples the spreading resistance from parasitic series resistance components. We show that this can be achieved by a force modulation (leading to a modulated spreading resistance signal) in combination with a lock-in deconvolution concept. In this paper we first introduce the principle of operation of the technique. We discuss in detail the underlying physical mechanisms as well as the technical implementation on a state-of-the-art atomic force microscope (AFM). We demonstrate the performance of FFT-SSRM and its ability to remove substantial series resistance components in practice. Eventually, the possibility of decoupling the spreading resistance from the intrinsic probe resistance will be demonstrated and discussed. - Highlights: • A novel electrical AFM mode for carrier profiling in confined volumes is presented. • Thereby the force and hence the contact area between AFM probe and sample is modulated. • Information on the spreading resistance is derived using a lock-in approach. • Bulk series resistance components are

Novel resistance functions uncovered using functional metagenomic investigations of resistance reservoirs

Directory of Open Access Journals (Sweden)

Erica C. Pehrsson

2013-06-01

Full Text Available Rates of infection with antibiotic-resistant bacteria have increased precipitously over the past several decades, with far-reaching healthcare and societal costs. Recent evidence has established a link between antibiotic resistance genes in human pathogens and those found in non-pathogenic, commensal, and environmental organisms, prompting deeper investigation of natural and human-associated reservoirs of antibiotic resistance. Functional metagenomic selections, in which shotgun-cloned DNA fragments are selected for their ability to confer survival to an indicator host, have been increasingly applied to the characterization of many antibiotic resistance reservoirs. These experiments have demonstrated that antibiotic resistance genes are highly diverse and widely distributed, many times bearing little to no similarity to known sequences. Through unbiased selections for survival to antibiotic exposure, functional metagenomics can improve annotations by reducing the discovery of false-positive resistance and by allowing for the identification of previously unrecognizable resistance genes. In this review, we summarize the novel resistance functions uncovered using functional metagenomic investigations of natural and human-impacted resistance reservoirs. Examples of novel antibiotic resistance genes include those highly divergent from known sequences, those for which sequence is entirely unable to predict resistance function, bifunctional resistance genes, and those with unconventional, atypical resistance mechanisms. Overcoming antibiotic resistance in the clinic will require a better understanding of existing resistance reservoirs and the dissemination networks that govern horizontal gene exchange, informing best practices to limit the spread of resistance-conferring genes to human pathogens.

A study on heat resistance of high temperature resistant coating

Energy Technology Data Exchange (ETDEWEB)

Zhang, Liping; Wang, Xueying; Zhang, Qibin; Qin, Yanlong; Lin, Zhu [Research Institute of Engineering Technology of CNPC, Tianjin (China)

2005-04-15

A high temperature resistant coating has been developed, which is mainly for heavy oil production pipes deserved the serious corrosion. The coating has excellent physical and mechanical performance and corrosion resistance at room and high temperature. In order to simulate the underground working condition of heavy oil pipes,the heat resistance of the high temperature resistant coating has been studied. The development and a study on the heat resistance of the DHT high temperature resistance coating have been introduced in this paper

A study on heat resistance of high temperature resistant coating

International Nuclear Information System (INIS)

Zhang, Liping; Wang, Xueying; Zhang, Qibin; Qin, Yanlong; Lin, Zhu

2005-01-01

A high temperature resistant coating has been developed, which is mainly for heavy oil production pipes deserved the serious corrosion. The coating has excellent physical and mechanical performance and corrosion resistance at room and high temperature. In order to simulate the underground working condition of heavy oil pipes,the heat resistance of the high temperature resistant coating has been studied. The development and a study on the heat resistance of the DHT high temperature resistance coating have been introduced in this paper

Detection of resistance, cross-resistance, and stability of resistance to new chemistry insecticides in Bemisia tabaci (Homoptera: Aleyrodidae).

Science.gov (United States)

Basit, Muhammad; Saeed, Shafqat; Saleem, Mushtaq Ahmad; Denholm, Ian; Shah, Maqbool

2013-06-01

Resistance levels in whitefly, Bemisia tabaci (Gennadius) collections from cotton and sunflower (up to four districts) for five neonicotinoids and two insect growth regulators (IGRs) were investigated for two consecutive years. Based on the LC50(s), all collections showed slight to moderate levels of resistance for the tested insecticides compared with the laboratory susceptible population. The data also indicated that cotton and sunflower collections had similar resistance levels. In comparison (four collections), Vehari collections showed higher resistance for acetamiprid, thiacloprid, and nitenpyram compared with those of others. Average resistance ratios for acetamiprid, thiacloprid, and nitenpyram ranged from 5- to 13-, 4- to 8-, and 9- to 13-fold, respectively. Multan and Vehari collections also exhibited moderate levels (9- to 16-fold) of resistance to buprofezin. Furthermore, toxicity of neonicotinoids against immature stages was equal to that of insect growth regulators. The data also suggested that resistance in the field populations was stable. After selection for four generations with bifenthrin (G1 to G4), resistance to bifenthrin increased to 14-fold compared with the laboratory susceptible population. Selection also increased resistance to fenpropathrin, lambdacyhalothrin, imidacloprid, acetamiprid, and diafenthuron. Cross-resistance and stability of resistance in the field populations is of some concern. Rotation of insecticides having no cross-resistance and targeting the control against immature stages may control the resistant insects, simultaneously reducing the selection pressure imposed.

Resistant plasmid profile analysis of multidrug resistant Escherichia ...

African Journals Online (AJOL)

Background: Multi-drug resistant Escherichia coli has become a major threat and cause of many urinary tract infections (UTIs) in Abeokuta, Nigeria. Objectives: This study was carried out to determine the resistant plasmids of multidrug resistant Escherichia coli isolated from (Urinary tract infections)UTIs in Abeokuta.

Resistant plasmid profile analysis of multidrug resistant Escherichia ...

African Journals Online (AJOL)

Multiple drug resistance isolates causing UTI has seri- ous implications for the empiric therapy against patho- genic isolates and for the possible co-selection of antimicrobial resistant mediated by multi drug resistant plasmids21,22. E. coli from clinical isolates are known to harbour plasmids of different molecular sizes23.

Resistance to Linezolid

DEFF Research Database (Denmark)

Vester, Birte; Ntokou, Eleni

2017-01-01

Linezolid is an antimicrobial agent that binds to the bacterial ribosome and thereby inhibits protein synthesis. Soon after its release as a clinical drug, it became clear that bacteria could become resistant to linezolid. The resistance mechanisms are mainly causing alteration of the drug target...... site, but probably efflux might also play a role. The resistance is still rare in surveillance studies, but outbreaks of resistant clones from hospitals have been observed. So far the main mechanisms of resistance are occurrence of mutations in ribosomal genes or obtaining plasmids with a gene coding...... for a methyltransferase providing resistance. The most obvious way to avoid resistance may be development of derivatives of linezolid overcoming the known resistance mechanisms....

Low-level quinolone-resistance in multi-drug resistant typhoid

Energy Technology Data Exchange (ETDEWEB)

Mirza, S H; Khan, M A [Armed Forces Inst. of Pathology, Rawalpindi (Pakistan). Dept. of Microbiolgy

2008-01-15

To find out the frequency of low-level quinolone-resistance in Multi-Drug Resistant (MDR) typhoid using nalidixic acid screening disc. Blood was obtained from suspected cases of typhoid fever and cultured in to BacT/ALERT. The positive blood cultures bottles were subcultured. The isolates were identified by colony morphology and biochemical tests using API-20E galleries. Susceptibility testing of isolates was done by modified Kirby-Bauer disc diffusion method on Muellar Hinton Agar. For the isolates, which were resistant to nalidixic acid by disc diffusion method, Minimal Inhibitory Concentrations (MICs) of ciprofloxacin and nalidixic acid were determined by using the E-test strips. Disc diffusion susceptibility tests and MICs were interpreted according to the guidelines provided by National Committee for Control Laboratory Standard (NCCLS). A total of 21(65.5%) out of 32 isolates of Salmonellae were nalidixic acid-resistant by disk diffusion method. All the nalidixic acid-resistant isolates by disc diffusion method were confirmed by MICs for both ciprofloxacin and nalidixic acid. All the nalidixic acid-resistant isolates had a ciprofloxacin MIC of 0.25-1 microg/ml (reduced susceptibility) and nalidixic acid MICs > 32 microg (resistant). Out of all Salmonella isolates, 24 (75%) were found to be MDR, and all were S. typbi. Low-level quinolone-resistance in typhoid was high in this small series. Screening for nalidixic acid resistance with a 30 microg nalidixic acid disk is a reliable and cost-effective method to detect low-level fluoroquinolone resistance, especially in the developing countries. (author)

Low-level quinolone-resistance in multi-drug resistant typhoid

International Nuclear Information System (INIS)

Mirza, S.H.; Khan, M.A.

2008-01-01

To find out the frequency of low-level quinolone-resistance in Multi-Drug Resistant (MDR) typhoid using nalidixic acid screening disc. Blood was obtained from suspected cases of typhoid fever and cultured in to BacT/ALERT. The positive blood cultures bottles were subcultured. The isolates were identified by colony morphology and biochemical tests using API-20E galleries. Susceptibility testing of isolates was done by modified Kirby-Bauer disc diffusion method on Muellar Hinton Agar. For the isolates, which were resistant to nalidixic acid by disc diffusion method, Minimal Inhibitory Concentrations (MICs) of ciprofloxacin and nalidixic acid were determined by using the E-test strips. Disc diffusion susceptibility tests and MICs were interpreted according to the guidelines provided by National Committee for Control Laboratory Standard (NCCLS). A total of 21(65.5%) out of 32 isolates of Salmonellae were nalidixic acid-resistant by disk diffusion method. All the nalidixic acid-resistant isolates by disc diffusion method were confirmed by MICs for both ciprofloxacin and nalidixic acid. All the nalidixic acid-resistant isolates had a ciprofloxacin MIC of 0.25-1 microg/ml (reduced susceptibility) and nalidixic acid MICs > 32 microg (resistant). Out of all Salmonella isolates, 24 (75%) were found to be MDR, and all were S. typbi. Low-level quinolone-resistance in typhoid was high in this small series. Screening for nalidixic acid resistance with a 30 microg nalidixic acid disk is a reliable and cost-effective method to detect low-level fluoroquinolone resistance, especially in the developing countries. (author)

Antibiotic resistance

Directory of Open Access Journals (Sweden)

Marianne Frieri

2017-07-01

Full Text Available Summary: Antimicrobial resistance in bacterial pathogens is a challenge that is associated with high morbidity and mortality. Multidrug resistance patterns in Gram-positive and -negative bacteria are difficult to treat and may even be untreatable with conventional antibiotics. There is currently a shortage of effective therapies, lack of successful prevention measures, and only a few new antibiotics, which require development of novel treatment options and alternative antimicrobial therapies. Biofilms are involved in multidrug resistance and can present challenges for infection control. Virulence, Staphylococcus aureus, Clostridium difficile infection, vancomycin-resistant enterococci, and control in the Emergency Department are also discussed. Keywords: Antibiotic resistance, Biofilms, Infections, Public health, Emergency Department

Insecticide resistance and resistance mechanisms in bed bugs, Cimex spp. (Hemiptera: Cimicidae).

Science.gov (United States)

Dang, Kai; Doggett, Stephen L; Veera Singham, G; Lee, Chow-Yang

2017-06-29

The worldwide resurgence of bed bugs [both Cimex lectularius L. and Cimex hemipterus (F.)] over the past two decades is believed in large part to be due to the development of insecticide resistance. The transcriptomic and genomic studies since 2010, as well as morphological, biochemical and behavioral studies, have helped insecticide resistance research on bed bugs. Multiple resistance mechanisms, including penetration resistance through thickening or remodelling of the cuticle, metabolic resistance by increased activities of detoxification enzymes (e.g. cytochrome P450 monooxygenases and esterases), and knockdown resistance by kdr mutations, have been experimentally identified as conferring insecticide resistance in bed bugs. Other candidate resistance mechanisms, including behavioral resistance, some types of physiological resistance (e.g. increasing activities of esterases by point mutations, glutathione S-transferase, target site insensitivity including altered AChEs, GABA receptor insensitivity and altered nAChRs), symbiont-mediated resistance and other potential, yet undiscovered mechanisms may exist. This article reviews recent studies of resistance mechanisms and the genes governing insecticide resistance, potential candidate resistance mechanisms, and methods of monitoring insecticide resistance in bed bugs. This article provides an insight into the knowledge essential for the development of both insecticide resistance management (IRM) and integrated pest management (IPM) strategies for successful bed bug management.

Glyphosate-Resistant Parthenium hysterophorus in the Caribbean Islands: Non Target Site Resistance and Target Site Resistance in Relation to Resistance Levels.

Directory of Open Access Journals (Sweden)

Enzo Bracamonte

2016-12-01

Full Text Available Glyphosate has been the most intensely herbicide used worldwide for decades, and continues to be a single tool for controlling weeds in woody crops. However, the adoption of this herbicide in a wide range of culture systems has led to the emergence of resistant weeds. Glyphosate has been widely used primarily on citrus in the Caribbean area, but a study of resistance in the Caribbean islands of Cuba and the Dominican Republic has never been carried out. Unfortunately, Parthenium hysterophorus has developed glyphosate-resistance in both islands, independently. The resistance level and mechanisms of different P. hysterophorus accessions (three collected in Cuba (Cu-R and four collected in the Dominican Republic (Do-R have been studied under greenhouse and laboratory conditions. In in vivo assays (glyphosate dose causing 50% reduction in above-ground vegetative biomass and survival, the resistance factor levels showed susceptible accessions (Cu-S≥Do-S, low-resistance accessions (Cu-R3Do-R2>Cu-R2>Do-R3>Do-R4>Cu-R3>>Cu-S≥Do-S. Glyphosate was degraded to aminomethylphosphonic acid, glyoxylate and sarcosine by >88% in resistant accessions except in Cu-R3 and Do-R4 resistant accessions (51.12 and 44.21, respectively, whereas a little glyphosate (<9.32% was degraded in both susceptible accessions at 96 h after treatment. There were significant differences between P. hysterophorus accessions in the 5-enolpyruvylshikimate-3-phosphate synthase (EPSPS activity enzyme with and without different glyphosate rates. The R accessions showed values of between 0.026 and 0.21 µmol µg-1 TSP protein min-1 basal EPSPS activity values with respect to the S (0.024 and 0.025 accessions. The same trend was found in the EPSPS enzyme activity treated with glyphosate, where a higher enzyme activity inhibition (glyphosate µM corresponded to greater resistance levels in P. hysterophorus accessions. One amino acid substitution was found at position 106 in EPSPS, consisting

Equivalent network for resistance and temperature coefficient of resistance versus temperature and composition of thick resistive films

International Nuclear Information System (INIS)

Kusy, A.

1987-01-01

Two types of elementary resistances in thick resistive films have been considered: (i) constriction resistance R/sub C/ determined by the bulk properties of conducting material and by the geometry of constriction, and (ii) barrier resistance R/sub B/ determined by the parameters of a thermally activated type of tunneling process and by the geometry of the metal-insulator-metal unit. On this basis a resistance network composed of a large number of the two types of resistances has been defined. The network has been considered as being equivalent to thick resistive film (TRF) from the point of view of the resistance and temperature coefficient of resistance (TCR). The parameters of this network have been evaluated by the computer-aided approximation of the experimental data found for RuO 2 -based TRFs. On the basis of the equations derived for the network as well as the results of the approximation process, it can be concluded that the small values of the network TCR result from the superposition of the TCR of the conducting component β/sub C/ and of the temperature coefficient of barrier resistance α/sub B/. In this superposition β/sub C/ is attenuated (by 1--2 orders of magnitude), while α/sub B/ is attenuated by only few percentages. The network has been found to be strongly barrier dominated

Reconceptualizing resistance: sociology and the affective dimension of resistance.

Science.gov (United States)

Hynes, Maria

2013-12-01

This paper re-examines the sociological study of resistance in light of growing interest in the concept of affect. Recent claims that we are witness to an 'affective turn' and calls for a 'new sociological empiricism' sensitive to affect indicate an emerging paradigm shift in sociology. Yet, mainstream sociological study of resistance tends to have been largely unaffected by this shift. To this end, this paper presents a case for the significance of affect as a lens by which to approach the study of resistance. My claim is not simply that the forms of actions we would normally recognize as resistance have an affective dimension. Rather, it is that the theory of affect broadens 'resistance' beyond the purview of the two dominant modes of analysis in sociology; namely, the study of macropolitical forms, on the one hand, and the micropolitics of everyday resistance on the other. This broadened perspective challenges the persistent assumption that ideological forms of power and resistance are the most pertinent to the contemporary world, suggesting that much power and resistance today is of a more affective nature. In making this argument, it is a Deleuzian reading of affect that is pursued, which opens up to a level of analysis beyond the common understanding of affect as emotion. I argue that an affective approach to resistance would pay attention to those barely perceptible transitions in power and mobilizations of bodily potential that operate below the conscious perceptions and subjective emotions of social actors. These affective transitions constitute a new site at which both power and resistance operate. © London School of Economics and Political Science 2013.

Additional instructions related to VISA-2 experiment for instrumentation personnel on duty; Dodatak instrukcijama za dezurne instrumentatore u vezi eksperimenta VISA-2

Energy Technology Data Exchange (ETDEWEB)

Pavicevic, M; Nikolic, M [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-01-15

For measuring the temperature gradients between the inlet and outlet water in the reactor channels with VISA-2 irradiation capsules, the previously used platinum resistance thermometers are replaced by thermocouples. This document includes detailed instructions for using these new instruments for measuring the temperature gradients in each reactor channel during experiments. [Serbo-Croat] Za merenje razlike temperature ulazne i izlazne vode u tehnoloskim kanalima sa kapsulama VISA-2, nalaze se umesto dosadasnjih platinskim otpornih termometara, termoparovi koji mere razliku temperature po svakom kanalu. Ovaj dokument sadrzi detaljna uputstva za koriscenje novih instrumenata za merenje razlike temperature tokom eksperimenta.

Review of resistance factor for steel: resistance distributions and resistance factor calibration

International Nuclear Information System (INIS)

Schmidt, B.J.; Bartlett, F.M.

2002-01-01

Changes in the Canadian steel industry warrant a review of the steel resistance factor in CSA Standard S16 (formerly S16.1) 'Limit states design of steel structures', originally calibrated in the landmark study by Kennedy and Gad Aly in 1980. This paper presents statistical parameters for the bending, compression, and tension resistances of W, WWF, and HSS components produced since 1999 that have been derived from geometric and material properties presented in a companion paper. The resistance factor for steel was recalibrated for the live and dead load combination in the 1995 National Building Code of Canada. A resistance factor of 0.95 is suitable for laterally supported beams, stocky columns, and tension members failing by yield of the gross section, whereas the current value of 0.90 is appropriate for intermediate columns and tension members failing by fracture of the net section. (author)

Electrical resistivity measurements to predict abrasion resistance

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 31; Issue 2. Electrical resistivity measurements to predict abrasion resistance of rock aggregates ... It was seen that correlation coefficients were increased for the rock classes. In addition ...

Antimicrobial resistance determinant microarray for analysis of multi-drug resistant isolates

Science.gov (United States)

Taitt, Chris Rowe; Leski, Tomasz; Stenger, David; Vora, Gary J.; House, Brent; Nicklasson, Matilda; Pimentel, Guillermo; Zurawski, Daniel V.; Kirkup, Benjamin C.; Craft, David; Waterman, Paige E.; Lesho, Emil P.; Bangurae, Umaru; Ansumana, Rashid

2012-06-01

The prevalence of multidrug-resistant infections in personnel wounded in Iraq and Afghanistan has made it challenging for physicians to choose effective therapeutics in a timely fashion. To address the challenge of identifying the potential for drug resistance, we have developed the Antimicrobial Resistance Determinant Microarray (ARDM) to provide DNAbased analysis for over 250 resistance genes covering 12 classes of antibiotics. Over 70 drug-resistant bacteria from different geographic regions have been analyzed on ARDM, with significant differences in patterns of resistance identified: genes for resistance to sulfonamides, trimethoprim, chloramphenicol, rifampin, and macrolide-lincosamidesulfonamide drugs were more frequently identified in isolates from sources in Iraq/Afghanistan. Of particular concern was the presence of genes responsible for resistance to many of the last-resort antibiotics used to treat war traumaassociated infections.

Assessing resistance of stabilized corrosion resistant steels to intergranular corrosion

International Nuclear Information System (INIS)

Karas, A.; Cihal, V. Jr.; Vanek, V.; Herzan, J.; Protiva, K.; Cihal, V.

1987-01-01

Resistance to intergranular corrosion was determined for four types of titanium-stabilized steels from the coefficients of stabilization efficiency according to the degree the chemical composition was known. The ATA SUPER steel showed the highest resistance parameter value. The resistance of this type of steel of a specific composition, showing a relatively low value of mean nitrogen content was compared with steel of an optimized chemical composition and with low-carbon niobium stabilized, molybdenum modified steels. The comparison showed guarantees of a sufficient resistance of the steel to intergranular corrosion. The method of assessing the resistance to intergranular corrosion using the calculation of the minimum content of Cr', i.e., the effective chromium content, and the maximum effective carbon content C' giving the resistance parameter k seems to be prospective for practical use in the production of corrosion resistant steels. (author). 1 tab., 5 figs., 15 refs

A pilot study on the usefulness of peripheral blood flow cytometry for the diagnosis of lower risk myelodysplastic syndromes: the "MDS thermometer".

Science.gov (United States)

Aires, Ana; Teixeira, Maria Dos Anjos; Lau, Catarina; Moreira, Cláudia; Spínola, Ana; Mota, Alexandra; Freitas, Inês; Coutinho, Jorge; Lima, Margarida

2018-01-01

Immunophenotypic analysis of the bone marrow (BM) cells has proven to be helpful in the diagnosis of Myelodysplastic Syndromes (MDS). However, the usefulness of flow cytometry (FCM) for the detection of myelodysplasia in the peripheral blood (PB) still needs to be investigated. The aim of this pilot study was to evaluate the value of FCM-based PB neutrophil and monocyte immunophenotyping for the diagnosis of lower risk MDS (LR-MDS). We evaluated by 8-color FCM the expression of multiple cell surface molecules (CD10, CD11b, CD11c, CD13, CD14, CD15, CD16, CD34, CD45, CD56, CD64 and HLA-DR) in PB neutrophils and monocytes from a series of 14 adult LR-MDS patients versus 14 normal individuals. Peripheral blood neutrophils from patients with LR-MDS frequently had low forward scatter (FSC) and side scatter (SSC) values and low levels of CD11b, CD11c, CD10, CD16, CD13 and CD45 expression, in that order, as compared to normal neutrophils. In addition, patients with LR-MDS commonly display a higher fraction of CD14 + CD56 + and a lower fraction of CD14 + CD16 + monocytes in the PB. Based on these results, we proposed an immunophenotyping score based on which PB samples from patients with LR-MDS could be distinguished from normal PB samples with a sensitivity 93% and a specificity of 100%. In addition, we used this score to construct the MDS Thermometer, a screening tool for detection and monitoring of MDS in the PB in clinical practice. Peripheral blood neutrophil and monocyte immunophenotyping provide useful information for the diagnosis of LR-MDS, as a complement to cytomorphology. If validated by subsequent studies in larger series of MDS patients and extended to non-MDS patients with cytopenias, our findings may improve the diagnostic assessment and avoid invasive procedures in selected groups of MDS patients.

Resistant Hypertension.

Science.gov (United States)

Doroszko, Adrian; Janus, Agnieszka; Szahidewicz-Krupska, Ewa; Mazur, Grzegorz; Derkacz, Arkadiusz

2016-01-01

Resistant hypertension is a severe medical condition which is estimated to appear in 9-18% of hypertensive patients. Due to higher cardiovascular risk, this disorder requires special diagnosis and treatment. The heterogeneous etiology, risk factors and comorbidities of resistant hypertension stand in need of sophisticated evaluation to confirm the diagnosis and select the best therapeutic options, which should consider lifestyle modifications as well as pharmacological and interventional treatment. After having excluded pseudohypertension, inappropriate blood pressure measurement and control as well as the white coat effect, suspicion of resistant hypertension requires an analysis of drugs which the hypertensive patient is treated with. According to one definition - ineffective treatment with 3 or more antihypertensive drugs including diuretics makes it possible to diagnose resistant hypertension. A multidrug therapy including angiotensin - converting enzyme inhibitors, angiotensin II receptor blockers, beta blockers, diuretics, long-acting calcium channel blockers and mineralocorticoid receptor antagonists has been demonstrated to be effective in resistant hypertension treatment. Nevertheless, optional, innovative therapies, e.g. a renal denervation or baroreflex activation, may create a novel pathway of blood pressure lowering procedures. The right diagnosis of this disease needs to eliminate the secondary causes of resistant hypertension e.g. obstructive sleep apnea, atherosclerosis and renal or hormonal disorders. This paper briefly summarizes the identification of the causes of resistant hypertension and therapeutic strategies, which may contribute to the proper diagnosis and an improvement of the long term management of resistant hypertension.

Evaluering af øretemperaturmåling på en geriatrisk afdeling

DEFF Research Database (Denmark)

Christensen, P M; Christensen, V B; Matzen, L E

1998-01-01

We evaluated an infrared tympanic thermometer (Genius 3000A) by comparing it with parallel measurements with an electronic rectal thermometer (Philips HP 5316) on 121 patients admitted to a geriatric department. Rectal temperature was on average 0.14 degree C +/- (ISD) above the ear temperature. 95......% of the differences are within the interval from -1.18 degrees C to 1.46 degrees C. The coefficient of determination was only 0.30. The tympanic thermometer, Genius 3000A, cannot be recommended for daily use on a geriatric ward. Udgivelsesdato: 1998-Aug-31...

Antibiotic Resistance

DEFF Research Database (Denmark)

Munck, Christian

morbidity and mortality as well as an increase in the cost of treatment. Understanding how bacteria respond to antibiotic exposure gives the foundations for a rational approach to counteract antimicrobial resistance. In the work presented in this thesis, I explore the two fundamental sources...... of antimicrobial resistance: (1) adaptive mutations and (2) horizontal acquisition of resistance genes from antibiotic gene reservoirs. By studying the geno- and phenotypic changes of E. coli in response to single and drug-pair exposures, I uncover the evolutionary trajectories leading to adaptive resistance. I...... to rationally design drug combinations that limit the evolution of antibiotic resistance due to counteracting evolutionary trajectories. My results highlight that an in-depth knowledge about the genetic responses to the individual antimicrobial compounds enables the prediction of responses to drug combinations...

76 FR 2056 - Incorporation of Revised ASTM Standards That Provide Flexibility in the Use of Alternatives to...

Science.gov (United States)

2011-01-12

... development of the nervous system, resulting in learning disabilities. Elemental mercury and other forms of... use of mercury- containing thermometers for certain temperature measurement applications. EPA seeks to... in high temperature applications, such as the use of thermometers in autoclaves, traditionally...

Resistance and sheet resistance measurements using electron beam induced current

International Nuclear Information System (INIS)

Czerwinski, A.; Pluska, M.; Ratajczak, J.; Szerling, A.; KaPtcki, J.

2006-01-01

A method for measurement of spatially uniform or nonuniform resistance in layers and strips, based on electron beam induced current (EBIC) technique, is described. High electron beam currents are used so that the overall resistance of the measurement circuit affects the EBIC signal. During the evaluation, the electron beam is scanned along the measured object, whose load resistance varies with the distance. The variation is compensated by an adjustable resistance within an external circuit. The method has been experimentally deployed for sheet resistance determination of buried regions of lateral confinements in semiconductor laser heterostructures manufactured by molecular beam epitaxy

Dissemination of antibiotic resistance in methicillin-resistant Staphylococcus aureus and vancomycin-resistant S aureus strains isolated from hospital effluents.

Science.gov (United States)

Mandal, Santi M; Ghosh, Ananta K; Pati, Bikas R

2015-12-01

Vancomycin-resistant Staphylococcus aureus (VRSA) and methicillin-resistant S aureus (MRSA) strains were examined in hospital effluents. Most S aureus strains are resistant to methicillin (MRSA), followed by tetracycline. Approximately 15% of MRSA strains are also resistant to vancomycin (VRSA). All VRSA strains developed a VanR/VanS-regulated 2-component system of VanA-type resistance in their genome. Results indicate that there is a possibility of developing resistance to aminoglycosides by VRSA strains in the near future. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Dinitroaniline herbicide resistance in a multiple-resistant Lolium rigidum population.

Science.gov (United States)

Chen, Jinyi; Yu, Qin; Owen, Mechelle; Han, Heping; Powles, Stephen

2018-04-01

The pre-emergence dinitroaniline herbicides (such as trifluralin and pendimethalin) are vital to Australian no-till farming systems. A Lolium rigidum population collected from the Western Australian grain belt with a 12-year trifluralin use history was characterised for resistance to dinitroaniline, acetyl CoA carboxylase (ACCase)- and acetolactate synthase (ALS)-inhibiting herbicides. Target-site resistance mechanisms were investigated. This L. rigidum population exhibited 32-fold resistance to trifluralin, as compared with the susceptible population. It also displayed 12- to 30-fold cross-resistance to other dinitroaniline herbicides (pendimethalin, ethalfluralin and oryzalin). In addition, this population showed multiple resistance to commonly used post-emergence ACCase- and ALS-inhibiting herbicides. Two target-site α-tubulin gene mutations (Val-202-Phe and Thr-239-Ile) previously documented in other dinitroaniline-resistant weed species were identified, and some known target-site mutations in ACCase (Ile-1781-Leu, Asp-2078-Gly and Cys-2088-Arg) and ALS (Pro-197-Gln/Ser) were found in the same population. An agar-based Petri dish screening method was established for the rapid diagnosis of resistance to dinitroaniline herbicides. Evolution of target-site resistance to both pre- and post-emergence herbicides was confirmed in a single L. rigidum population. The α-tubulin mutations Val-202-Phe and Thr-239-Ile, documented here for the first time in L. rigidum, are likely to be responsible for dinitroaniline resistance in this population. Early detection of dinitroaniline herbicide resistance and integrated weed management strategies are needed to maintain the effectiveness of dinitroaniline herbicides. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Etoxazole resistance in predatory mite Phytoseiulus persimilis A.-H. (Acari: Phytoseiidae): Cross-resistance, inheritance and biochemical resistance mechanisms.

Science.gov (United States)

Yorulmaz Salman, Sibel; Aydınlı, Fatma; Ay, Recep

2015-07-01

Phytoseiulus persimilis of the family Phytoseiidae is an effective predatory mite species that is used to control pest mites. The LC50 and LC60 values of etoxazole were determined on P. persimilis using a leaf-disc method and spraying tower. A laboratory selection population designated ETO6 was found to have a 111.63-fold resistance to etoxazole following 6 selection cycles. This population developed low cross-resistance to spinosad, spiromesifen, acetamiprid, indoxacarb, chlorantraniliprole, milbemectin and moderate cross-resistance to deltamethrin. PBO, IBP and DEM synergised resistance 3.17-, 2.85- and 3.60-fold respectively. Crossing experiments revealed that etoxazole resistance in the ETO6 population was an intermediately dominant and polygenic. In addition, detoxifying enzyme activities were increased 2.71-fold for esterase, 3.09-fold for glutathione S-transferase (GST) and 2.76-fold for cytochrome P450 monooxygenase (P450) in the ETO6 population. Selection for etoxazole under laboratory conditions resulted in the development of etoxazole resistance in the predatory mite P. persimilis that are resistant to pesticides are considered valuable for use in resistance management programmes within integrated pest control strategies. Copyright © 2014 Elsevier Inc. All rights reserved.

Relaxation resistance of heat resisting alloys with cobalt

International Nuclear Information System (INIS)

Borzdyka, A.M.

1977-01-01

Relaxation resistance of refractory nickel-chromium alloys containing 5 to 14 % cobalt is under study. The tests involve the use of circular samples at 800 deg to 850 deg C. It is shown that an alloy containing 14% cobalt possesses the best relaxation resistance exceeding that of nickel-chromium alloys without any cobalt by a factor of 1.5 to 2. The relaxation resistance of an alloy with 5% cobalt can be increased by hardening at repeated loading

Phenotypic- and Genotypic-Resistance Detection for Adaptive Resistance Management in Tetranychus urticae Koch.

Directory of Open Access Journals (Sweden)

Deok Ho Kwon

Full Text Available Rapid resistance detection is necessary for the adaptive management of acaricide-resistant populations of Tetranychus urticae. Detection of phenotypic and genotypic resistance was conducted by employing residual contact vial bioassay (RCV and quantitative sequencing (QS methods, respectively. RCV was useful for detecting the acaricide resistance levels of T. urticae, particularly for on-site resistance detection; however, it was only applicable for rapid-acting acaricides (12 out of 19 tested acaricides. QS was effective for determining the frequencies of resistance alleles on a population basis, which corresponded to 12 nonsynonymous point mutations associated with target-site resistance to five types of acaricides [organophosphates (monocrotophos, pirimiphos-methyl, dimethoate and chlorpyrifos, pyrethroids (fenpropathrin and bifenthrin, abamectin, bifenazate and etoxazole]. Most field-collected mites exhibited high levels of multiple resistance, as determined by RCV and QS data, suggesting the seriousness of their current acaricide resistance status in rose cultivation areas in Korea. The correlation analyses revealed moderate to high levels of positive relationships between the resistance allele frequencies and the actual resistance levels in only five of the acaricides evaluated, which limits the general application of allele frequency as a direct indicator for estimating actual resistance levels. Nevertheless, the resistance allele frequency data alone allowed for the evaluation of the genetic resistance potential and background of test mite populations. The combined use of RCV and QS provides basic information on resistance levels, which is essential for choosing appropriate acaricides for the management of resistant T. urticae.

LDMOS Channel Thermometer Based on a Thermal Resistance Sensor for Balancing Temperature in Monolithic Power ICs

Directory of Open Access Journals (Sweden)

Tingyou Lin

2017-06-01

Full Text Available This paper presents a method of thermal balancing for monolithic power integrated circuits (ICs. An on-chip temperature monitoring sensor that consists of a poly resistor strip in each of multiple parallel MOSFET banks is developed. A temperature-to-frequency converter (TFC is proposed to quantize on-chip temperature. A pulse-width-modulation (PWM methodology is developed to balance the channel temperature based on the quantization. The modulated PWM pulses control the hottest of metal-oxide-semiconductor field-effect transistor (MOSFET bank to reduce its power dissipation and heat generation. A test chip with eight parallel MOSFET banks is fabricated in TSMC 0.25 μm HV BCD processes, and total area is 900 × 914 μm2. The maximal temperature variation among the eight banks can reduce to 2.8 °C by the proposed thermal balancing system from 9.5 °C with 1.5 W dissipation. As a result, our proposed system improves the lifetime of a power MOSFET by 20%.

Resistant mechanisms and molecular epidemiology of imipenem-resistant Acinetobacter baumannii.

Science.gov (United States)

Xiao, Shu-Zhen; Chu, Hai-Qing; Han, Li-Zhong; Zhang, Zhe-Min; Li, Bing; Zhao, Lan; Xu, Liyun

2016-09-01

The aim of the study was to investigate the resistant mechanisms and homology of imipenem-resistant Acinetobacter baumannii (A. baumannii). A total of 46 non-duplicate imipenem‑resistant A. baumannii clinical isolates were collected from three tertiary hospitals between July, 2011 and June, 2012. The minimal inhibitory concentrations (MICs) of antimicrobial agents were determined using the agar dilution method. Phenylalanine‑arginine β-naphthylamide was used to detect the presence of the efflux pump-mediated resistant mechanism. Polymerase chain reaction was employed to amplify genes associated with drug resistance, including β‑lactamase genes, efflux pump genes and outer membrane protein gene CarO. A few amplicons were randomly selected and sequenced. Multilocus sequence analysis (MLST) was employed in typing A. baumanni. A. baumannii was resistant to imipenem, simultaneously showing resistance to several other antimicrobials. In addtition, 13 A. baumannii were found to mediate drug resistance through operation of the efflux pump. Of the various drug resistance genes tested, blaOXA‑51 was present in 46 isolates, blaOXA‑23 gene was present in 44 isolates and blaNDM gene was found in only one strain. Other drug resistant‑associated genes, including blaKPC, blaIMP, blaOXA-24, blaOXA‑58, blaSHV, blaGIM and blaVIM were not detected. Mutation of adeS and outer membrane protein gene CarO were found in a few of the imipenem‑resistant isolates. The MLST analysis revealed that all 46 clinical isolates were clustered into 11 genotypes and the most frequent genotype was ST208. In conclusion, β‑lactamase genes, genes involved in efflux pump and mutation of outer membrane protein encoding gene may be important in mediating imipenem resistance in A. baumannii. Of the 11 different genotypes, ST11 was shared by the majority of A. baumannii, which may be due to horizontal transfer of patients from hospitals.

Multidrug-Resistant Candida

DEFF Research Database (Denmark)

Arendrup, Maiken Cavling; Patterson, Thomas F

2017-01-01

Invasive Candida infections remain an important cause of morbidity and mortality, especially in hospitalized and immunocompromised or critically ill patients. A limited number of antifungal agents from only a few drug classes are available to treat patients with these serious infections. Resistance...... can be either intrinsic or acquired. Resistance mechanisms are not exchanged between Candida; thus, acquired resistance either emerges in response to an antifungal selection pressure in the individual patient or, more rarely, occur due to horizontal transmission of resistant strains between patients....... Although multidrug resistance is uncommon, increasing reports of multidrug resistance to the azoles, echinocandins, and polyenes have occurred in several Candida species, most notably Candida glabrata and more recently Candida auris. Drivers are overall antifungal use, subtherapeutic drug levels at sites...

Examination of the suitability of noise thermometry for precise in situ calibration of thermocouples in technical processes

International Nuclear Information System (INIS)

Fechner, H.

1988-12-01

The aim was to determine the achievable accuracy of the noise thermometer developed at the KFA in the range from 0 to 1000 0 C under laboratory conditions. Precision noise temperature measurements at fixed temperature points (triple point of water, freezing point of zinc and silver) were carried out. The fixed point technique and the conventional precision resistance thermometry, which is required to operate the fixed points, were established in accordance with the requirements of accurate (and thus longer lasting) noise temperature measurements. The analysis of all possible sources of error ensured that all systematic or random errors were in the range of a few 10 -5 . The further developed KFA noise thermometers, which can be used under industrial conditions, achieve under laboratory conditions a measuring error of about ±2.5 10 -4 - relative to the thermodynamic temperature scale - in the temperature range from 273.16 K (0.01 0 C) to 1234.894 K (961.744 0 C). Assuming that the individual measured values display a normal distribution, the noise measurements at the zinc and silver point are combined to a mean value, it becomes apparent that the average noise temperatures only deviate by +2 10 -5 (zinc) or +4 10 -5 (silver) from the respective thermodynamic temperature. (orig./HP) [de

On the results of investigating cause of sodium leak accident in prototype fast breeder reactor 'Monju' in Power Reactor and Nuclear Fuel Development Corporation

International Nuclear Information System (INIS)

1997-01-01

The sodium leak accident in the secondary system of Monju occurred on December 8, 1995. The task force for investigating the accident was established in Nuclear Safety Bureau, and on May 23, 1996, the May report on the results of investigation was published. In order to elucidate the details of the fact that only one thermometer in the secondary system was broken and the reaction of leaked sodium with steel materials, the investigation was continued. In this report, also the results of these additional investigations are included. First, the accident of this time is outlined. As for the cause of the occurrence of sodium leak, the examination of the fracture surface of the broken thermometer, the high cycle fatigue due to hydrodynamic vibration, the investigation of the design, manufacture and installation of the thermometer, and the evaluation of secondary system thermometers which were not broken are reported. The cause that only one thermometer was broken was the way of its insertion which made the restraint of vibration amplitude ineffective. As the effects of sodium leak, the pile of sodium compound on floor liner, the damage of ducts and gratings, and the color change of concrete walls were observed. The burning experiment due to sodium leak was carried out to confirm the effects. (K.I.)

Combating Antibiotic Resistance

Science.gov (United States)

... Bacteria Phasing Out Certain Antibiotic Use in Farm Animals FDA: Cutting-Edge Technology Sheds Light on Antibiotic Resistance For More Information Antibiotics and Antibiotic Resistance Antimicrobial Resistance Information for Consumers and Health Professionals CDC: ...

HIV Resistance Testing

Science.gov (United States)

... 14, 2016 Select a Language: Fact Sheet 126 HIV Resistance Testing WHAT IS RESISTANCE? HOW DOES RESISTANCE ... ARVs. If you miss doses of your medications, HIV will multiply more easily. More mutations will occur. ...

Using data on resistance prevalence per sample in the surveillance of antimicrobial resistance

DEFF Research Database (Denmark)

Vieira, Antonio; Shuyu, Wu; Jensen, Lars Bogø

2008-01-01

Objectives: In most existing antimicrobial resistance monitoring programmes, one single bacterial colony from each collected sample is susceptibility tested against a panel of antimicrobials. Detecting the proportion of colonies resistant to different antimicrobials in each sample can provide...... quantitative data on antimicrobial resistance (resistance prevalence per sample). Methods: In this study, a total of 98 faecal samples from slaughter pigs were tested for tetracycline and sulphonamide resistance in Escherichia coli using the single colony method, and these results were compared...... with the results obtained using the resistance prevalence per sample method. Results: The results obtained by the resistance prevalence per sample method showed a lower occurrence of resistance. Tetracycline resistance in E. coli was found in 36.7% of the samples using the single colony method, while the mean...

Resisting Organizational Change

OpenAIRE

Andersson, Gunnar

2015-01-01

We are continuously reminded of how change induces controversy and resistance, regardless of support. We repeatedly experience resistance in difficulties of implementation, little progress, and poor results, rather than increased productivity as anticipated. In a detailed account of how change plays out, a mosaic of what resistance looks like emerges. The picture is both familiar and absolutely concrete, and challenges the structural assumptions and dichotomies on support and resistance in an...

High chlorpyrifos resistance in Culex pipiens mosquitoes: strong synergy between resistance genes

Science.gov (United States)

Alout, H; Labbé, P; Berthomieu, A; Makoundou, P; Fort, P; Pasteur, N; Weill, M

2016-01-01

We investigated the genetic determinism of high chlorpyrifos resistance (HCR), a phenotype first described in 1999 in Culex pipiens mosquitoes surviving chlorpyrifos doses ⩾1 mg l−1 and more recently found in field samples from Tunisia, Israel or Indian Ocean islands. Through chlorpyrifos selection, we selected several HCR strains that displayed over 10 000-fold resistance. All strains were homozygous for resistant alleles at two main loci: the ace-1 gene, with the resistant ace-1R allele expressing the insensitive G119S acetylcholinesterase, and a resistant allele of an unknown gene (named T) linked to the sex and ace-2 genes. We constructed a strain carrying only the T-resistant allele and studied its resistance characteristics. By crossing this strain with strains harboring different alleles at the ace-1 locus, we showed that the resistant ace-1R and the T alleles act in strong synergy, as they elicited a resistance 100 times higher than expected from a simple multiplicative effect. This effect was specific to chlorpyrifos and parathion and was not affected by synergists. We also examined how HCR was expressed in strains carrying other ace-1-resistant alleles, such as ace-1V or the duplicated ace-1D allele, currently spreading worldwide. We identified two major parameters that influenced the level of resistance: the number and the nature of the ace-1-resistant alleles and the number of T alleles. Our data fit a model that predicts that the T allele acts by decreasing chlorpyrifos concentration in the compartment targeted in insects. PMID:26463842

Measurement of Dynamic Resistance in Resistance Spot Welding

DEFF Research Database (Denmark)

Wu, Pei; Lu, J.; Zhang, Wenqi

2007-01-01

is influenced by inductive noise caused by the high welding current. In this study, the dynamic resistance is determined by measuring the voltage at primary side and current at secondary side. This increases the accuracy of measurement because of higher signal-noise ratio, and allows to apply to in-process......The conventional methods of determining the dynamic resistance were mostly done by measuring the voltage and current at secondary side of transformer in resistance welding machines, in which the measuring set-up normally interferes with the movement of electrode, and the measuring precision...

DIRProt: a computational approach for discriminating insecticide resistant proteins from non-resistant proteins.

Science.gov (United States)

Meher, Prabina Kumar; Sahu, Tanmaya Kumar; Banchariya, Anjali; Rao, Atmakuri Ramakrishna

2017-03-24

Insecticide resistance is a major challenge for the control program of insect pests in the fields of crop protection, human and animal health etc. Resistance to different insecticides is conferred by the proteins encoded from certain class of genes of the insects. To distinguish the insecticide resistant proteins from non-resistant proteins, no computational tool is available till date. Thus, development of such a computational tool will be helpful in predicting the insecticide resistant proteins, which can be targeted for developing appropriate insecticides. Five different sets of feature viz., amino acid composition (AAC), di-peptide composition (DPC), pseudo amino acid composition (PAAC), composition-transition-distribution (CTD) and auto-correlation function (ACF) were used to map the protein sequences into numeric feature vectors. The encoded numeric vectors were then used as input in support vector machine (SVM) for classification of insecticide resistant and non-resistant proteins. Higher accuracies were obtained under RBF kernel than that of other kernels. Further, accuracies were observed to be higher for DPC feature set as compared to others. The proposed approach achieved an overall accuracy of >90% in discriminating resistant from non-resistant proteins. Further, the two classes of resistant proteins i.e., detoxification-based and target-based were discriminated from non-resistant proteins with >95% accuracy. Besides, >95% accuracy was also observed for discrimination of proteins involved in detoxification- and target-based resistance mechanisms. The proposed approach not only outperformed Blastp, PSI-Blast and Delta-Blast algorithms, but also achieved >92% accuracy while assessed using an independent dataset of 75 insecticide resistant proteins. This paper presents the first computational approach for discriminating the insecticide resistant proteins from non-resistant proteins. Based on the proposed approach, an online prediction server DIRProt has

Resistance patterns, prevalence, and predictors of fluoroquinolones resistance in multidrug resistant tuberculosis patients

Directory of Open Access Journals (Sweden)

Nafees Ahmad

2016-01-01

Conclusion: The high degree of drug resistance observed, particularly to fluoroquinolones, is alarming. We recommend the adoption of more restrictive policies to control non-prescription sale of fluoroquinolones, its rational use by physicians, and training doctors in both private and public–private mix sectors to prevent further increase in fluoroquinolones resistant Mycobacterium tuberculosis strains.

Shear flow generation and turbulence suppression by resistive ballooning and resistive interchange modes

International Nuclear Information System (INIS)

Guzdar, P.N.; Drake, J.F.

1993-01-01

The generation of shear flow by resistive ballooning modes and resistive interchange modes is compared and contrasted using a 3-D fluid code. The resistive ballooning modes give rise to poloidally asymmetric transport and hence drive poloidal rotation due to the Reynold's Stress as well as the anomalous Stringer/Winsor mechanism. On the other hand the resistive interchange mode can drive shear flow only through the Reynold's Stress. The studies show that if the self-consistent sheared flow is suppressed, the resistive ballooning modes give rise to a larger anomalous transport than produced by the resistive interchange modes. Furthermore the shear flow generated by the resistive ballooning modes is larger than that driven by the resistive interchange modes due to the combined effect of the dual mechanisms stated earlier. As a consequence strong suppression of the fluctuations as well as reduction of the transport occurs for resistive ballooning modes. On the other hand, for the resistive interchange modes the level of fluctuation as well as the anomalous transport is not reduced by the self consistent shear flow generated by the Reynold's Stress. This latter result is in agreement with some earlier 3-D simulation of resistive interchange modes

Rapid report acetamiprid resistance and cross-resistance in the diamondback moth, Plutella xylostella.

Science.gov (United States)

Ninsin, Kodwo D

2004-09-01

A 110-fold acetamiprid-resistant Plutella xylostella (L) strain was established after four selection experiments (in five generations) on a 9.5-fold resistant colony in the laboratory. The resistant strain did not show cross-resistance to chlorfluazuron or Bacillus thuringiensis subsp kurstaki Berliner, but displayed low resistance to cartap and phenthoate.

Occurrence of integrons and resistance genes among sulphonamide-resistant Shigella spp. from Brazil

DEFF Research Database (Denmark)

Peirano, G.; Agersø, Yvonne; Aarestrup, Frank Møller

2005-01-01

Objectives: To determine the occurrence of class 1 and 2 integrons and antimicrobial resistance genes among sulphonamide-resistant Shigella strains isolated in Brazil during 1999-2003. Methods: Sixty-two Shigella (Shigella flexneri, n = 47 and Shigella sonnei, n = 15) were tested against 21...... antimicrobial agents. The presence of integrons classes 1 and 2 and antimicrobial resistance genes was investigated by PCR using specific primers. Results: A total of eight antimicrobial resistance profiles were identified, with the profile of resistance to sulfamethoxazole, trimethoprim, spectinomycin...... of 2214 bp harbouring a gene cassette array conferring resistance to trimethoprim, streptothricin and spectinomycin/streptomycin. The genes coding for resistance to chloramphenicol (catA1), tetracycline [tet(A) and tet(B)] and ampicillin (bla(OXA) and bla(TEM)), were detected in resistant strains...

Multidrug-resistant tuberculosis

Directory of Open Access Journals (Sweden)

McNerney Ruth

2008-01-01

Full Text Available Abstract Background With almost 9 million new cases each year, tuberculosis remains one of the most feared diseases on the planet. Led by the STOP-TB Partnership and WHO, recent efforts to combat the disease have made considerable progress in a number of countries. However, the emergence of mutated strains of Mycobacterium tuberculosis that are resistant to the major anti-tuberculosis drugs poses a deadly threat to control efforts. Multidrug-resistant tuberculosis (MDR-TB has been reported in all regions of the world. More recently, extensively drug resistant-tuberculosis (XDR-TB that is also resistant to second line drugs has emerged in a number of countries. To ensure that adequate resources are allocated to prevent the emergence and spread of drug resistance it is important to understand the scale of the problem. In this article we propose that current methods of describing the epidemiology of drug resistant tuberculosis are not adequate for this purpose and argue for the inclusion of population based statistics in global surveillance data. Discussion Whereas the prevalence of tuberculosis is presented as the proportion of individuals within a defined population having disease, the prevalence of drug resistant tuberculosis is usually presented as the proportion of tuberculosis cases exhibiting resistance to anti-tuberculosis drugs. Global surveillance activities have identified countries in Eastern Europe, the former Soviet Union and regions of China as having a high proportion of MDR-TB cases and international commentary has focused primarily on the urgent need to improve control in these settings. Other regions, such as sub-Saharan Africa have been observed as having a low proportion of drug resistant cases. However, if one considers the incidence of new tuberculosis cases with drug resistant disease in terms of the population then countries of sub-Saharan Africa have amongst the highest rates of transmitted MDR-TB in the world. We propose

Resistant and Refractory Hypertension: Antihypertensive Treatment Resistance vs Treatment Failure

Science.gov (United States)

Siddiqui, Mohammed; Dudenbostel, Tanja; Calhoun, David A.

2017-01-01

Resistant or difficult to treat hypertension is defined as high blood pressure that remains uncontrolled with 3 or more different antihypertensive medications, including a diuretic. Recent definitions also include controlled blood pressure with use of 4 or more medications as also being resistant to treatment. Recently, refractory hypertension, an extreme phenotype of antihypertensive treatment failure has been defined as hypertension uncontrolled with use of 5 or more antihypertensive agents, including a long-acting thiazide diuretic and a mineralocorticoid receptor antagonist. Patients with resistant vs refractory hypertension share similar characteristics and comorbidities, including obesity, African American race, female sex, diabetes, coronary heart disease, chronic kidney disease, and obstructive sleep apnea. Patients with refractory vs resistant hypertension tend to be younger and are more likely to have been diagnosed with congestive heart failure. Refractory hypertension might also differ from resistant hypertension in terms of underlying cause. Preliminary evidence suggests that refractory hypertension is more likely to be neurogenic in etiology (ie, heightened sympathetic tone), vs a volume-dependent hypertension that is more characteristic of resistant hypertension in general. PMID:26514749

Extensively Drug-Resistant Tuberculosis: Principles of Resistance, Diagnosis, and Management.

Science.gov (United States)

Wilson, John W; Tsukayama, Dean T

2016-04-01

Extensively drug-resistant (XDR) tuberculosis (TB) is an unfortunate by-product of mankind's medical and pharmaceutical ingenuity during the past 60 years. Although new drug developments have enabled TB to be more readily curable, inappropriate TB management has led to the emergence of drug-resistant disease. Extensively drug-resistant TB describes Mycobacterium tuberculosis that is collectively resistant to isoniazid, rifampin, a fluoroquinolone, and an injectable agent. It proliferates when established case management and infection control procedures are not followed. Optimized treatment outcomes necessitate time-sensitive diagnoses, along with expanded combinations and prolonged durations of antimicrobial drug therapy. The challenges to public health institutions are immense and most noteworthy in underresourced communities and in patients coinfected with human immunodeficiency virus. A comprehensive and multidisciplinary case management approach is required to optimize outcomes. We review the principles of TB drug resistance and the risk factors, diagnosis, and managerial approaches for extensively drug-resistant TB. Treatment outcomes, cost, and unresolved medical issues are also discussed. Copyright © 2016 Mayo Foundation for Medical Education and Research. Published by Elsevier Inc. All rights reserved.

Prevalence of chlorhexidine-resistant methicillin-resistant Staphylococcus aureus following prolonged exposure.

Science.gov (United States)

Schlett, Carey D; Millar, Eugene V; Crawford, Katrina B; Cui, Tianyuan; Lanier, Jeffrey B; Tribble, David R; Ellis, Michael W

2014-08-01

Chlorhexidine has been increasingly utilized in outpatient settings to control methicillin-resistant Staphylococcus aureus (MRSA) outbreaks and as a component of programs for MRSA decolonization and prevention of skin and soft-tissue infections (SSTIs). The objective of this study was to determine the prevalence of chlorhexidine resistance in clinical and colonizing MRSA isolates obtained in the context of a community-based cluster-randomized controlled trial for SSTI prevention, during which 10,030 soldiers were issued chlorhexidine for body washing. We obtained epidemiological data on study participants and performed molecular analysis of MRSA isolates, including PCR assays for determinants of chlorhexidine resistance and high-level mupirocin resistance and pulsed-field gel electrophoresis (PFGE). During the study period, May 2010 to January 2012, we identified 720 MRSA isolates, of which 615 (85.4%) were available for molecular analysis, i.e., 341 clinical and 274 colonizing isolates. Overall, only 10 (1.6%) of 615 isolates were chlorhexidine resistant, including three from the chlorhexidine group and seven from nonchlorhexidine groups (P > 0.99). Five (1.5%) of the 341 clinical isolates and five (1.8%) of the 274 colonizing isolates harbored chlorhexidine resistance genes, and four (40%) of the 10 possessed genetic determinants for mupirocin resistance. All chlorhexidine-resistant isolates were USA300. The overall prevalence of chlorhexidine resistance in MRSA isolates obtained from our study participants was low. We found no association between extended chlorhexidine use and the prevalence of chlorhexidine-resistant MRSA isolates; however, continued surveillance is warranted, as this agent continues to be utilized for infection control and prevention efforts. Copyright © 2014, American Society for Microbiology. All Rights Reserved.

KTA 625 alloy tube with excellent corrosion resistance and heat resistance

International Nuclear Information System (INIS)

Fujiwara, Kazuo; Kadonaga, Toshiki; Kikuma, Seiji.

1982-01-01

The problems when seamless tubes are produced by using nickel base 625 alloy (61Ni-22Cr-9Mo-Cb) which is known as a corrosion resistant and heat resistant alloyF were examined, and the confirmation experiment was carried out on its corrosion resistance and heat resistance. Various difficulties have been experienced in the tube making owing to the characteristics due to the chemical composition, but they were able to be solved by the repeated experiments. As for the characteristics of the product, the corrosion resistance was excellent particularly in the environment containing high temperature, high concentration chloride, and also the heat resistance was excellent in the wide temperature range from normal temperature to 1000 deg C. From these facts, the wide fields of application are expected for these alloy tubes, including the evaporation and concentration equipment for radioactive wastes in atomic energy field. Expecting the increase of demand hereafter, Kobe Steel Ltd. examined the problems when seamless tubes are produced from the 625 alloy by Ugine Sejournet process. The aptitude for tube production such as the chemical composition, production process and the product characteristics, the corrosion resistance against chloride, hydrogen sulfide, polythionic and other acids,F the high temperature strength and oxidation resistance are reported. (Kako, I.)

La0.7Sr0.3MnO3 Thin Films for Magnetic and Temperature Sensors at Room Temperature

Directory of Open Access Journals (Sweden)

Sheng Wu

2012-03-01

Full Text Available In this paper, the potentialities of the manganese oxide La0.7Sr0.3MnO3 (LSMO for the realization of sensitive room temperature thermometers and magnetic sensors are discussed. LSMO exhibits both a large change of the resistance versus temperature at its metal-to-insulator transition (about 330 K and low field magnetoresistive effects at room temperature. The sensor performances are described in terms of signal-to-noise ratio in the 1 Hz - 100 kHz frequency range. It is shown that due to the very low 1/f noise level, LSMO based sensors can exhibit competitive performances at room temperature.

Basal-plane thermal conductivity of few-layer molybdenum disulfide

International Nuclear Information System (INIS)

Jo, Insun; Ou, Eric; Shi, Li; Pettes, Michael Thompson; Wu, Wei

2014-01-01

We report the in-plane thermal conductivity of suspended exfoliated few-layer molybdenum disulfide (MoS 2 ) samples that were measured by suspended micro-devices with integrated resistance thermometers. The obtained room-temperature thermal conductivity values are (44–50) and (48–52) W m −1 K −1 for two samples that are 4 and 7 layers thick, respectively. For both samples, the peak thermal conductivity occurs at a temperature close to 120 K, above which the thermal conductivity is dominated by intrinsic phonon-phonon scattering although phonon scattering by surface disorders can still play an important role in these samples especially at low temperatures

Cross-Resistance of UV- or Chlorine Dioxide-Resistant Echovirus 11 to Other Disinfectants

Directory of Open Access Journals (Sweden)

Qingxia Zhong

2017-10-01

Full Text Available The emergence of waterborne viruses with resistance to disinfection has been demonstrated in the laboratory and in the environment. Yet, the implications of such resistance for virus control remain obscure. In this study we investigate if viruses with resistance to a given disinfection method exhibit cross-resistance to other disinfectants. Chlorine dioxide (ClO2- or UV-resistant populations of echovirus 11 were exposed to five inactivating treatments (free chlorine, ClO2, UV radiation, sunlight, and heat, and the extent of cross-resistance was determined. The ClO2-resistant population exhibited cross-resistance to free chlorine, but to none of the other inactivating treatments tested. We furthermore demonstrated that ClO2 and free chlorine act by a similar mechanism, in that they mainly inhibit the binding of echovirus 11 to its host cell. As such, viruses with host binding mechanisms that can withstand ClO2 treatment were also better able to withstand oxidation by free chlorine. Conversely, the UV-resistant population was not significantly cross-resistant to any other disinfection treatment. Overall, our results indicate that viruses with resistance to multiple disinfectants exist, but that they can be controlled by inactivating methods that operate by a distinctly different mechanism. We therefore suggest to utilize two disinfection barriers that act by different mechanisms in order to control disinfection-resistant viruses.

Fabrication of internally instrumented reactor fuel rods

International Nuclear Information System (INIS)

Schmutz, J.D.; Meservey, R.H.

1975-01-01

Procedures are outlined for fabricating internally instrumented reactor fuel rods while maintaining the original quality assurance level of the rods. Instrumented fuel rods described contain fuel centerline thermocouples, ultrasonic thermometers, and pressure tubes for internal rod gas pressure measurements. Descriptions of the thermocouples and ultrasonic thermometers are also contained

on germination of chickpea seed

African Journals Online (AJOL)

patience

2014-01-01

Jan 1, 2014 ... capacitor and a thermometer was inserted horizontally. To make good contact between the thermometer and disc, some mercury was poured into the ..... magnetic fields on growth parameters of young sun flower and wheat seedlings. Bioelectromagnetics 25:638-641. Florez M, Carbonell MV, Martínez E ...

Animation of Antimicrobial Resistance

Medline Plus

Full Text Available ... Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing options ... of Animation of Antimicrobial Resistance More in Antimicrobial ... Antimicrobial Resistance Monitoring System About NARMS 2015 NARMS Integrated ...

Antibiotic resistance reservoirs

NARCIS (Netherlands)

Versluis, Dennis

2016-01-01

One of the major threats to human health in the 21st century is the emergence of pathogenic bacteria that are resistant to multiple antibiotics, thereby limiting treatment options. An important route through which pathogens become resistant is via acquisition of resistance genes from

An Experimental Study of the Electrical Contact Resistance in Resistance Welding

DEFF Research Database (Denmark)

Song, Quanfeng; Zhang, Wenqi; Bay, Niels

2005-01-01

Electrical contact resistance is of critical importance in resistance welding. In this article, the contact resistance is experimentally investigated for welding mild steel, stainless steel, and aluminum to themselves. A parametric study was carried out on a Gleeble® machine, investigating...

Analysis and modeling of resistive switching mechanisms oriented to resistive random-access memory

International Nuclear Information System (INIS)

Huang Da; Wu Jun-Jie; Tang Yu-Hua

2013-01-01

With the progress of the semiconductor industry, the resistive random-access memory (RAM) has drawn increasing attention. The discovery of the memristor has brought much attention to this study. Research has focused on the resistive switching characteristics of different materials and the analysis of resistive switching mechanisms. We discuss the resistive switching mechanisms of different materials in this paper and analyze the differences of those mechanisms from the view point of circuitry to establish their respective circuit models. Finally, simulations are presented. We give the prospect of using different materials in resistive RAM on account of their resistive switching mechanisms, which are applied to explain their resistive switchings

Antimicrobial Resistance

Science.gov (United States)

... least 10 countries (Australia, Austria, Canada, France, Japan, Norway, Slovenia, South Africa, Sweden and the United Kingdom ... plan Global report on surveillance Country situation analysis Policy to combat antimicrobial resistance More on antimicrobial resistance ...

Antimicrobial Resistance

Science.gov (United States)

... can prevent and manage antimicrobial resistance. It is collaborating with partners to strengthen the evidence base and ... on the global action plan. WHO has been leading multiple initiatives to address antimicrobial resistance: World Antibiotic ...

Pyrethroid resistance and cross-resistance in the German cockroach, Blattella germanica (L).

Science.gov (United States)

Wei, Y; Appel, A G; Moar, W J; Liu, N

2001-11-01

A German cockroach (Blatella germanica (L)) strain, Apyr-R, was collected from Opelika, Alabama after control failures with pyrethroid insecticides. Levels of resistance to permethrin and deltamethrin in Apyr-R (97- and 480-fold, respectively, compared with a susceptible strain, ACY) were partially or mostly suppressed by piperonyl butoxide (PBO) and S,S,S,-tributylphosphorotrithioate (DEF), suggesting that P450 monooxygenases and hydrolases are involved in resistance to these two pyrethroids in Apyr-R. However, incomplete suppression of pyrethroid resistance with PBO and DEF implies that one or more additional mechanisms are involved in resistance. Injection, compared with topical application, resulted in 43- and 48-fold increases in toxicity of permethrin in ACY and Apyr-R, respectively. Similarly, injection increased the toxicity of deltamethrin 27-fold in ACY and 28-fold in Apyr-R. These data indicate that cuticular penetration is one of the obstacles for the effectiveness of pyrethroids against German cockroaches. However, injection did not change the levels of resistance to either permethrin or deltamethrin, suggesting that a decrease in the rate of cuticular penetration may not play an important role in pyrethroid resistance in Apyr-R. Apyr-R showed cross-resistance to imidacloprid, with a resistance ratio of 10. PBO treatment resulted in no significant change in the toxicity of imidacloprid, implying that P450 monooxygenase-mediated detoxication is not the mechanism responsible for cross-resistance. Apyr-R showed no cross-resistance to spinosad, although spinosad had relatively low toxicity to German cockroaches compared with other insecticides tested in this study. This result further confirmed that the mode of action of spinosad to insects is unique. Fipronil, a relatively new insecticide, was highly toxic to German cockroaches, and the multi-resistance mechanisms in Apyr-R did not confer significant cross-resistance to this compound. Thus, we propose

Resistance and cross-resistance profile of the diaryltriazine NNRTI and candidate microbicide UAMC01398.

Science.gov (United States)

Ariën, Kevin K; Venkatraj, Muthusamy; Michiels, Johan; Joossens, Jurgen; Vereecken, Katleen; Van der Veken, Pieter; Heeres, Jan; De Winter, Hans; Heyndrickx, Leo; Augustyns, Koen; Vanham, Guido

2016-05-01

The resistance development, cross-resistance to other NNRTIs and the impact of resistance on viral replicative fitness were studied for the new and potent NNRTI UAMC01398. Resistance was selected by dose escalation and by single high-dose selection against a comprehensive panel of NNRTIs used as therapeutics and NNRTIs under investigation for pre-exposure prophylaxis of sexual HIV transmission. A panel of 27 site-directed mutants with single mutations or combinations of mutations involved in reverse transcriptase (RT) inhibitor-mediated resistance was developed and used to confirm resistance to UAMC01398. Cross-resistance to other NNRTIs was assessed, as well as susceptibility of UAMC01398-resistant HIV to diarylpyrimidine-resistant viruses. Finally, the impact of UAMC01398 resistance on HIV replicative fitness was studied. We showed that UAMC01398 has potent activity against dapivirine-resistant HIV, that at least four mutations in the RT are required in concert for resistance and that the resistance profile is similar to rilpivirine, both genotypically and phenotypically. Resistance development to UAMC01398 is associated with a severe fitness cost. These data, together with the enhanced safety profile and good solubility in aqueous gels, make UAMC01398 an excellent candidate for HIV topical prevention. © The Author 2016. Published by Oxford University Press on behalf of the British Society for Antimicrobial Chemotherapy. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Resisting Mind Control.

Science.gov (United States)

Anderson, Susan M.; Zimbardo, Philip G.

1980-01-01

Provides conceptual analyses of mind control techniques along with practical advice on how to resist these techniques. The authors stress that effective mind control stems more from everyday social relations than from exotic technological gimmicks. Suggestions are given for resisting persuasion, resisting systems, and challenging the system.…

Cross-resistance and Inheritance of Resistance to Emamectin Benzoate in Spodoptera exigua (Lepidoptera: Noctuidae).

Science.gov (United States)

Che, Wunan; Huang, Jianlei; Guan, Fang; Wu, Yidong; Yang, Yihua

2015-08-01

Beet armyworm, Spodoptera exigua (Hübner), is a worldwide pest of many crops. Chemical insecticides are heavily used for its control in China, and serious resistance has been evolved in the field to a variety of insecticides including emamectin benzoate. Through repeated backcrossing to a susceptible strain (WH-S) and selection with emamectin benzoate, the trait conferring resistance to emamectin benzoate in a field-collected population of S. exigua (moderately resistant to emamectin benzoate and strongly resistant to pyrethroids and indoxacarb) was introgressed into WH-S to generate a near-isogenic resistant strain (WH-EB). Compared with WH-S, the WH-EB strain developed a 1,110-fold resistance to emamectin benzoate and a high level of cross-resistance to abamectin (202-fold), with low levels of cross-resistance to cypermethrin (10-fold) and chlorfluazuron (7-fold), but no cross-resistance to representatives of another six different classes of insecticides (chlorantraniliprole, chlorfenapyr, indoxacarb, spinosad, tebufenozide, and chlorpyrifos). Resistance to emamectin benzoate in WH-EB was autosomal, incompletely dominant, and polygenic. Limited cross-resistance in WH-EB indicates that emamectin benzoate can be rotated with other classes of insecticides to which it does not show cross-resistance to delay the evolution of resistance in S. exigua. The incompletely dominant nature of resistance in S. exigua may explain the rapid evolution of resistance to emamectin benzoate in the field, and careful deployment of this chemical within a resistance management program should be considered. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Resistance to lambda-cyhalothrin in Spanish field populations of Ceratitis capitata and metabolic resistance mediated by P450 in a resistant strain.

Science.gov (United States)

Arouri, Rabeh; Le Goff, Gaelle; Hemden, Hiethem; Navarro-Llopis, Vicente; M'saad, Mariem; Castañera, Pedro; Feyereisen, René; Hernández-Crespo, Pedro; Ortego, Félix

2015-09-01

The withdrawal of malathion in the European Union in 2009 resulted in a large increase in lambda-cyhalothrin applications for the control of the Mediterranean fruit fly, Ceratitis capitata, in Spanish citrus crops. Spanish field populations of C. capitata have developed resistance to lambda-cyhalothrin (6-14-fold), achieving LC50 values (129-287 ppm) higher than the recommended concentration for field treatments (125 ppm). These results contrast with the high susceptibility to lambda-cyhalothrin found in three Tunisian field populations. We have studied the mechanism of resistance in the laboratory-selected resistant strain W-1Kλ (205-fold resistance). Bioassays with synergists showed that resistance was almost completely suppressed by the P450 inhibitor PBO. The study of the expression of 53 P450 genes belonging to the CYP4, CYP6, CYP9 and CYP12 families in C. capitata revealed that CYP6A51 was overexpressed (13-18-fold) in the resistant strain. The W-1Kλ strain also showed high levels of cross-resistance to etofenprox (240-fold) and deltamethrin (150-fold). Field-evolved resistance to lambda-cyhalothrin has been found in C. capitata. Metabolic resistance mediated by P450 appears to be the main resistance mechanism in the resistant strain W-1Kλ. The levels of cross-resistance found may compromise the effectiveness of other pyrethroids for the control of this species. © 2014 Society of Chemical Industry. © 2014 Society of Chemical Industry.

Resistance to Powdery Mildews

DEFF Research Database (Denmark)

Siwoszek, Agnieszka Izabela

in majority of them. Resistance to barley powdery mildew in the field is controlled by use of resistant varieties in a combination with fungicides. Early disease management is crucial for effective control. Yet, the pathogen commonly develops fungicide resistance due to simple point mutations. Several studies...... protection. In the present study, I provide an overview of the current knowledge about plant pathogens and plant disease resistance. I use Arabidopsis as a model to investigate the mechanism of non-host resistance, presumed to be the most durable and broad-spectrum form of resistance. I attempt to determine...

Vital Signs - Multiple Languages

Science.gov (United States)

... Well-Being 9 - Thermometer Basics - Amarɨñña / አማርኛ (Amharic) MP3 Siloam Family Health Center Arabic (العربية) Expand Section ... Well-Being 9 - Thermometer Basics - myanma bhasa (Burmese) MP3 Siloam Family Health Center Dari (دری) Expand Section ...

plasmid mediated resistance in multidrug resistant bacteria isolated

African Journals Online (AJOL)

User

PLASMID MEDIATED RESISTANCE IN MULTIDRUG RESISTANT BACTERIA. ISOLATED FROM CHILDREN WITH SUSPECTED SEPTICAEMIA IN ZARIA,. NIGERIA. AbdulAziz, Z. A.,1* Ehinmidu, J. O.,1 Adeshina, G. O.,1 Pala, Y. Y2., Yusuf, S. S2. and. Bugaje, M. A.3. 1Department of Pharmaceutics and Pharmaceutical ...

Electrical resistivity measurements to predict abrasion resistance of ...

Indian Academy of Sciences (India)

WINTEC

increasing expansion of highway and other construction works and decreasing natural aggregate resources in the world, the demand for crushed stone aggregates has in- creased from day-to-day. One of the important properties of rock aggregates is abrasion resistance. The abrasion resistance of aggregates is generally ...

Resistant hypertension.

Science.gov (United States)

Wei, Fang-Fei; Zhang, Zhen-Yu; Huang, Qi-Fang; Yang, Wen-Yi; Staessen, Jan A

2018-06-15

The publication of the first non-randomised proof-of-concept trial of renal denervation as a treatment modality in treatment-resistant hypertension set the stage for a search for novel devices with the expectation that technology would reduce the burden of hypertension by reducing or eliminating the costly and lifelong use of blood pressure lowering medications. As we demonstrate in this review, this idea so attractive to manufacturers and invasive cardiologists and radiologists overlooked decades of careful pathophysiological research in a disease, which still remains enigmatic but remains the major cause of cardiovascular mortality worldwide. To make our point, we first reviewed the prevalence and risks associated with treatment-resistant hypertension. Next, we highlighted the key points required for the diagnosis of treatment-resistant hypertension, including the recording of the ambulatory blood pressure and the assessment of adherence to medication. Finally, we summarised new insights in the management of treatment-resistant hypertension by medication and devices and in the future research. Throughout our review, we focused on new evidence became available since 2013. Our conclusion is that optimising medical treatment based on simple algorithms remains the state of the art in treatment-resistant hypertension.

A Crystallization-Temperature Profile Through Paleo-Oceanic Crust (Wadi Gideah Transect, Oman Ophiolite): Application of the REE-in-Plagioclase-Clinopyroxene Partitioning Thermometer

Science.gov (United States)

Mueller, S.; Hasenclever, J.; Garbe-Schönberg, D.; Koepke, J.; Hoernle, K.

2017-12-01

The accretion mechanisms forming oceanic crust at fast spreading ridges are still under controversial discussion. Thermal, petrological, and geochemical observations predict different end-member models, i.e., the gabbro glacier and the sheeted sill model. They all bear implications for heat transport, temperature distribution, mode of crystallization and hydrothermal heat removal over crustal depth. In a typical MOR setting, temperature is the key factor driving partitioning of incompatible elements during crystallization. LA-ICP-MS data for co-genetic plagioclase and clinopyroxene in gabbros along a transect through the plutonic section of paleo-oceanic crust (Wadi Gideah Transect, Oman ophiolite) reveal that REE partitioning coefficients are relatively constant in the layered gabbro section but increase for the overlying foliated gabbros, with an enhanced offset towards HREEs. Along with a systematic enrichment of REE's with crustal height, these trends are consistent with a system dominated by in-situ crystallization for the lower gabbros and a change in crystallization mode for the upper gabbros. Sun and Liang (2017) used experimental REE partitioning data for calibrating a new REE-in-plagioclase-clinopyroxene thermometer that we used here for establishing the first crystallization-temperature depth profile through oceanic crust that facilitates a direct comparison with thermal models of crustal accretion. Our results indicate crystallization temperatures of about 1220±8°C for the layered gabbros and lower temperatures of 1175±8°C for the foliated gabbros and a thermal minimum above the layered-to-foliated gabbro transition. Our findings are consistent with a hybrid accretion model for the oceanic crust. The thermal minimum is assumed to represent a zone where the descending crystal mushes originating from the axial melt lens meet with mushes that have crystallized in situ. These results can be used to verify and test thermal models (e.g., Maclennan et al

Radiation thermometry - non-contact temperature measurements; Strahlungsthermometrie - Temperaturen beruehrungslos messen

Energy Technology Data Exchange (ETDEWEB)

Hollandt, J. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany). Fachbereich Hochtemperatur- und Vakuumphysik; Hartmann, J. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany). Arbeitsgruppe Hochtemperaturskala; Gutschwager, B. [Physikalisch-Technische Bundesanstalt (PTB), Braunschweig (Germany). Arbeitsgruppe Infrarot-Strahlungsthermometrie; Struss, O. [HEITRONICS Infrarot Messtechnik GmbH (Germany)

2007-09-15

The temperature is one of the measurands most frequently determined, as it decisively influences physical, chemical and biological processes. To be able to evaluate, optimize, repeat and compare industrial procedures, temperatures must be measured with sufficient accuracy and worldwide uniformity. This is done with the aid of the regulations and instructions of the international temperature scale. Today, non-contact measurements of surface temperatures can be performed without problems with radiation thermometers over a temperature range from -100 C up to 3000 C. Compared to contacting measurements, radiation-thermometric temperature measurement offers a series of advantages. Radiation thermometers react very fast and the measurement is not influenced by heat supply or dissipation. This allows objects to be measured which move very fast, are energized or may experience fast temperature changes. Consequently, radiation thermometry is increasingly used for the monitoring and control of thermal processes, for maintenance and in building services engineering. The present contribution shall inform of the fundamentals of radiation-thermometric temperature measurement as well as of the construction and popular types of radiation thermometers. It will be explained how exact and worldwide uniform temperature measurement is guaranteed via the international temperature scale and the calibration of radiation thermometers. The emissivity of surfaces which is important in practical temperature measurements and some examples of industrial applications of radiation thermometers will be described. (orig.)

Radiation thermometry - non-contact temperature measurements; Strahlungsthermometrie - Temperaturen beruehrungslos messen

Energy Technology Data Exchange (ETDEWEB)

Hollandt, J.; Hartmann, J.; Gutschwager, B. [Physikalisch-Technische Bundesanstalt, Berlin (Germany); Struss, O. [HEITRONICS Infrarot Messtechnik GmbH, Wiesbaden (Germany)

2006-07-01

The temperature is one of the measurands most frequently determined, as it decisively influences physical, chemical and biological processes. To be able to evaluate, optimize, repeat and compare industrial procedures, temperatures must be measured with sufficient accuracy and worldwide uniformity. This is done with the aid of the regulations and instructions of the international temperature scale. Today, non-contact measurements of surface temperatures can be performed without problems with radiation thermometers over a temperature range from -100 C up to 3000 C. Compared to contacting measurements, radiation-thermometric temperature measurement offers a series of advantages. Radiation thermometers react very fast and the measurement is not influenced by heat supply or dissipation. This allows objects to be measured which move very fast, are energized or may experience fast temperature changes. Consequently, radiation thermometry is increasingly used for the monitoring and control of thermal processes, for maintenance and in building services engineering. The present contribution shall inform of the fundamentals of radiation-thermometric temperature measurement as well as of the construction and popular types of radiation thermometers. It will be explained how exact and worldwide uniform temperature measurement is guaranteed via the international temperature scale and the calibration of radiation thermometers. The emissivity of surfaces which is important in practical temperature measurements and some examples of industrial applications of radiation thermometers will be described. (orig.)

[Resistance risk and resistance stability of Frankliniella occidentalis to imidacloprid, emamectin benzoate, and phoxim].

Science.gov (United States)

Wang, Sheng-Yin; Yu, Yi; Liu, Yong-Jie; Ma, Jing-Yu

2012-12-01

In order to effectively control the damage of Frankliniella occidentalis (Pergande), Phaseolus vuglaris was dipped with imidacloprid, phoxim, and emamectin benzoate, respectively to select the resistance populations of F. occidentalis from its susceptible population, and the resistance inheritance and resistance risk were analyzed with the resistance reality heredity. After 32, 32, and 24 generations' selection, the F. occidentalis populations obtained 13.8-fold, 29.4-fold and 39.0-fold resistance to imidacloprid, phoxim, and emamectin benzoate, respectively. The resistance reality heritability to imidacloprid, phoxim, and emamectin benzoate was 0.112, 0.166, and 0.259, respectively. The resistance development rate to emamectin benzoate was the fastest, followed by to phoxim, and to imidacloprid. The higher the resistance levels of the selected populations, the lower the differences between the larva and adult susceptibility to imidacloprid, phoxim, and emamectin benzoate. Stopping selection for 12 continuous generations, the resistance level of the selected resistance populations to imidacloprid, phoxim, and emamectin benzoate had definite decline, but it was difficult to regain the original susceptibility. F. occidentalis had a greater potential to gain high level resistance to imidacloprid, phoxim, and emamectin benzoate. Compared with the resistance of F. occidentalis to phoxim and emamectin benzoate, the resistance to imidacloprid increased slower and decreased faster, and thus, imidacloprid was more appropriate to control F. occidentalis in practice.

Resistance Selection and Characterization of Chlorantraniliprole Resistance in Plutella xylostella (Lepidoptera: Plutellidae).

Science.gov (United States)

Liu, Xia; Wang, Hong-Yan; Ning, Yu-Bo; Qiao, Kang; Wang, Kai-Yun

2015-08-01

The diamondback moth, Plutella xylostella (L.), is considered one of the most damaging lepidopteran pests, and it has developed resistance to all conventional insecticide classes in the field. Chlorantraniliprole is the first commercial insecticide that belongs to the new chemical class of diamide insecticides. But, P. xylostella have already shown resistance to chlorantraniliprole in China. After 52 generations of selection with chlorantraniliprole, ∼48.17-fold resistance was observed. The resistant strain showed cross-resistance to flubendiamide (7.29-fold), abamectin (6.11-fold), and cyantraniliprole (3.31-fold). Quantitative real-time polymerase chain reaction analysis showed that the expression of the ryanodine receptor gene was higher in the resistant strain than that in the susceptible strain. Enzyme assays indicated that cytochrome P450 activity in the resistant strain was 4.26 times higher compared with the susceptible strain, whereas no difference was seen for glutathione-S-transferase and esterase. Moreover, the toxicity of chlorantraniliprole in the resistant strain could be synergized by piperonyl butoxide, but not by diethyl maleate, and S,S,S-tributyl phosphorothioate. These results can serve as an important base for guiding the use of insecticide in field and delaying the development of pests that are resistant to the insecticides. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Emergence of multidrug-resistant, extensively drug-resistant and untreatable gonorrhea

Science.gov (United States)

Unemo, Magnus; Nicholas, Robert A

2013-01-01

The new superbug Neisseria gonorrhoeae has retained resistance to antimicrobials previously recommended for first-line treatment and has now demonstrated its capacity to develop resistance to the extended-spectrum cephalosporin, ceftriaxone, the last remaining option for first-line empiric treatment of gonorrhea. An era of untreatable gonorrhea may be approaching, which represents an exceedingly serious public health problem. Herein, we review the evolution, origin and spread of antimicrobial resistance and resistance determinants (with a focus on extended-spectrum cephalosporins) in N. gonorrhoeae, detail the current situation regarding verified treatment failures with extended-spectrum cephalosporins and future treatment options, and highlight essential actions to meet the large public health challenge that arises with the possible emergence of untreatable gonorrhea. Essential actions include: implementing action/response plans globally and nationally; enhancing surveillance of gonococcal antimicrobial resistance, treatment failures and antimicrobial use/misuse; and improving prevention, early diagnosis and treatment of gonorrhea. Novel treatment strategies, antimicrobials (or other compounds) and, ideally, a vaccine must be developed. PMID:23231489

Study of thermal effects in superconducting RF cavities

International Nuclear Information System (INIS)

Bousson, S.; Caruette, A.; Fouaidy, M.; Hammoudi, N.; Junquera, T.; Lesrel, J.; Yaniche, J.F.

1999-01-01

A high speed thermometric system equipped with 64 fixed surface thermometers is used to investigate thermal effects in several 3 GHz cavities. An evaluation of the time response of our thermometers is presented. A method based on RF signal analysis is proposed to evaluate the normal zone propagation rate during thermal breakdown. (authors)

Cold chain status at immunisation centres in Ethiopia | Berhane ...

African Journals Online (AJOL)

Objective: To assess the status of the cold chain at peripheral vaccine stores in Ethiopia. Design: Institution based cross-sectional survey in two rural and one urban ... Complete temperature record was observed in 37(57.8%) of the centres. Thermometer was not available in four (6.3%) and thermometer reading was found ...

Cross-resistance, inheritance and biochemical mechanisms of imidacloprid resistance in B-biotype Bemisia tabaci.

Science.gov (United States)

Wang, Zhenyu; Yao, Mingde; Wu, Yidong

2009-11-01

The B-type Bemisia tabaci (Gennadius) has become established in many regions in China, and neonicotinoids are extensively used to control this pest. Imidacloprid resistance in a laboratory-selected strain of B-type B. tabaci was characterised in order to provide the basis for recommending resistance management tactics. The NJ-Imi strain of B-type B. tabaci was selected from the NJ strain with imidacloprid for 30 generations. The NJ-Imi strain exhibited 490-fold resistance to imidacloprid, high levels of cross-resistance to three other neonicotinoids, low levels of cross-resistance to monosultap, cartap and spinosad, but no cross-resistance to abamectin and cypermethrin. Imidacloprid resistance in the NJ-Imi strain was autosomal and semi-dominant. It is shown that enhanced detoxification mediated by cytochrome-P450-dependent monooxygenases contributes to imidacloprid resistance to some extent in the NJ-Imi strain. Results from synergist bioassays and cross-resistance patterns indicated that target-site insensitivity may be involved in imidacloprid resistance in the NJ-Imi strain of B. tabaci. Although oxidative detoxification mediated by P450 monooxygenases is involved in imidacloprid resistance in the NJ-Imi strain of B-type B. tabaci, target-site modification as an additional resistance mechanism cannot be ruled out. Considering the high risk of cross-resistance, neonicotinoids should be regarded as a single group when implementing an insecticide rotation scheme in B. tabaci control. (c) 2009 Society of Chemical Industry.

Mechanisms of Antibiotic Resistance

Science.gov (United States)

Munita, Jose M.; Arias, Cesar A.

2015-01-01

Emergence of resistance among the most important bacterial pathogens is recognized as a major public health threat affecting humans worldwide. Multidrug-resistant organisms have emerged not only in the hospital environment but are now often identified in community settings, suggesting that reservoirs of antibiotic-resistant bacteria are present outside the hospital. The bacterial response to the antibiotic “attack” is the prime example of bacterial adaptation and the pinnacle of evolution. “Survival of the fittest” is a consequence of an immense genetic plasticity of bacterial pathogens that trigger specific responses that result in mutational adaptations, acquisition of genetic material or alteration of gene expression producing resistance to virtually all antibiotics currently available in clinical practice. Therefore, understanding the biochemical and genetic basis of resistance is of paramount importance to design strategies to curtail the emergence and spread of resistance and devise innovative therapeutic approaches against multidrug-resistant organisms. In this chapter, we will describe in detail the major mechanisms of antibiotic resistance encountered in clinical practice providing specific examples in relevant bacterial pathogens. PMID:27227291

Animation of Antimicrobial Resistance

Medline Plus

Full Text Available ... video) Animation of Antimicrobial Resistance (text version) Arabic Translation of Animation of Antimicrobial Resistance Chinese Translation of Animation of Antimicrobial Resistance French Translation of ...

Mango resistance to fruit flies. II - resistance of the alfa cultivar

Energy Technology Data Exchange (ETDEWEB)

Rossetto, C.J.; Bortoletto, N., E-mail: rossetto@iac.sp.gov.b [Agencia Paulista de Tecnologia dos Agronegocios (APTA), Votuporanga, SP (Brazil). Polo Regional do Noroeste Paulista; Walder, J.M.M.; Mastrangelo, T. de A., E-mail: jmwalder@cena.usp.b [Centro de Energia Nuclear na Agricultura (CENA/USP), Piracicaba, SP (Brazil); Carvalho, C.R.L.; Castro, J.V. de, E-mail: climonta@iac.sp.gov.b, E-mail: josalba@iac.sp.gov.b [Instituto Agronomico de Campinas, SP (Brazil); Pinto, A.C. de Q. [EMBRAPA, Brasilia, DF (Brazil); Cortelazzo, A.L., E-mail: angelo@unicamp.b [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Inst. de Biologia

2006-07-01

The percentage of infested mango fruits of five selected mango varieties was evaluated during three years under field conditions. Three varieties with field resistance to fruit flies had less then 10% of fruits infested. Tommy Atkins, the susceptible commercial check, had 42,9% and the susceptible check had 98.9 % of infested fruits. The three field resistant varieties plus the susceptible commercial check, Tommy Atkins, were further tested in laboratory, under caged conditions, with artificial infestation of Anastrepha obliqua. The attempts of oviposition and the number of pupae developed from each fruit were evaluated. Under caged conditions, the cultivar Alfa maintained its field resistance and Espada Stahl and IAC 111 lost the field resistance and were as susceptible as Tommy Atkins. The attempts of oviposition were positively and highly correlated with the number of pupae developed in the fruits. Non preference for oviposition was confirmed as the main mechanism of resistance of mango fruits to fruit flies. In the absence of a more susceptible variety (no choice test) the cultivar Alfa has kept the resistance (author)

Mango resistance to fruit flies. II - resistance of the alfa cultivar

International Nuclear Information System (INIS)

Rossetto, C.J.; Bortoletto, N.; Carvalho, C.R.L.; Castro, J.V. de; Pinto, A.C. de Q.; Cortelazzo, A.L.

2006-01-01

The percentage of infested mango fruits of five selected mango varieties was evaluated during three years under field conditions. Three varieties with field resistance to fruit flies had less then 10% of fruits infested. Tommy Atkins, the susceptible commercial check, had 42,9% and the susceptible check had 98.9 % of infested fruits. The three field resistant varieties plus the susceptible commercial check, Tommy Atkins, were further tested in laboratory, under caged conditions, with artificial infestation of Anastrepha obliqua. The attempts of oviposition and the number of pupae developed from each fruit were evaluated. Under caged conditions, the cultivar Alfa maintained its field resistance and Espada Stahl and IAC 111 lost the field resistance and were as susceptible as Tommy Atkins. The attempts of oviposition were positively and highly correlated with the number of pupae developed in the fruits. Non preference for oviposition was confirmed as the main mechanism of resistance of mango fruits to fruit flies. In the absence of a more susceptible variety (no choice test) the cultivar Alfa has kept the resistance (author)

Cross-resistance of bisultap resistant strain of Nilaparvata lugens and its biochemical mechanism.

Science.gov (United States)

Ling, Shanfeng; Zhang, Runjie

2011-02-01

The resistant (R) strain of the planthopper Nilaparvata lugens (Stål) selected for bisultap resistance displayed 7.7-fold resistance to bisultap and also had cross-resistance to nereistoxin (monosultap, thiocyclam, and cartap), chlorpyrifos, dimethoate, and malathion but no cross-resistance to buprofezin, imidacloprid, and fipronil. To find out the biochemical mechanism of resistance to bisultap, biochemical assay was done. The results showed that cytochrome P450 monooxygenases (P450) activity in R strain was 2.71-fold that in susceptible strain (S strain), in which the changed activity for general esterase (EST) was 1.91 and for glutathione S-transferases only 1.32. Piperonyl butoxide (PBO) could significantly inhibit P450 activity (percentage of inhibition [PI]: 37.31%) in the R strain, with ESTs PI = 16.04% by triphenyl phosphate (TPP). The results also demonstrated that diethyl maleate had no synergism with bisultap. However, PBO displayed significant synergism in three different strains, and the synergism increased with resistance (S strain 1.42, Lab strain, 2.24 and R strain, 3.23). TPP also showed synergism for three strains, especially in R strain (synergistic ratio = 2.47). An in vitro biochemical study and in vivo synergistic study indicated that P450 might be play important role in the biochemical mechanism of bisultap resistance and that esterase might be the important factor of bisultap resistance. Acetylcholinesterase (AChE) insensitivity play important role in bisultap resistance. We suggest that buprofezin, imidacloprid, and fipronil could be used in resistance management programs for N. lugens via alternation and rotation with bisultap.

Drug-resistant tuberculosis in Sindh

International Nuclear Information System (INIS)

Almani, S.A.; Memon, N.M.; Qureshi, A.F.

2002-01-01

Objective: To assess the prevalence of primary and secondary drug resistance amongst the clinical isolates of M.tuberculosis, to identify risk factors and how to overcome this problem. Design: A case series of 50 indoor patients with sputum smear-positive pulmonary tuberculosis. Place and duration of Study: Department of Medicine, Liaquat University of Medical and Health Sciences Jamshoro, Sindh, (Pakistan) from January 1999 to December 2000. Patients and methods: Four first line anti-tuberculous drugs rifampicine, ethambutol and streptomycin were tested for sensitivity pattern. Results: Twelve (26.66%) were sensitive to all four drugs, 12(26.66%) were resistant to one drug, 14 (31.11%) were resistant to two drugs, 2 (4.44%) were resistant to three drugs, and 5(11.11%) were resistant to all four drugs. Resistance to isoniazid was the most common in 27 cases (60%) with primary resistance in 6(13.33%) and secondary resistance in 21(46.66%), followed by resistance to streptomycin in 17 cases (37.77%) with primary resistance in 5(11.11%) and secondary resistance in 12 (26.66%). Resistance to ethambutol in 10 cases (22.22%) and rifampicine in 11 (24.44%) and all cases were secondary. Similarly multi-drugs resistance (MRD) TB was found in 11(24.44%) isolates. Conclusion: This study showed high prevalence of drug resistance among clinical isolates of M. tuberculosis. Their is a need to establish centers at number of places with adequate facilities for susceptibility testing so that the resistant pattern could be ascertained and treatment regimens tailored accordingly. (author)

Meteorological Sensor Array (MSA)-Phase I. Volume 3 (Pre-Field Campaign Sensor Calibration)

Science.gov (United States)

2015-07-01

Phase I thermodynamic sensors (barometers, thermometers, hygrometers, and pyranometers ). This report documents the results of a detailed calibration...barometer, thermometer, hydrometer, pyranometer 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT UU 18. NUMBER...60 (02 Mar); the logger associated with each non-standard RH sensor is demonstrated in the legend ...............21 Fig. 16 Pyranometers percent

Corrosion-resistant metal surfaces

Science.gov (United States)

Sugama, Toshifumi [Wading River, NY

2009-03-24

The present invention relates to metal surfaces having thereon an ultrathin (e.g., less than ten nanometer thickness) corrosion-resistant film, thereby rendering the metal surfaces corrosion-resistant. The corrosion-resistant film includes an at least partially crosslinked amido-functionalized silanol component in combination with rare-earth metal oxide nanoparticles. The invention also relates to methods for producing such corrosion-resistant films.

Contribution of non-target-site resistance in imidazolinone-resistant Imisun sunflower

Directory of Open Access Journals (Sweden)

Gabriela Breccia

2017-08-01

Full Text Available ABSTRACT The first commercial herbicide-resistant trait in sunflower (Helianthus annuus L. is known as ‘Imisun’. Imidazolinone resistance in Imisun cultivars has been reported to be genetically controlled by a major gene (known as Imr1 or Ahasl1-1 and modifier genes. Imr1 is an allelic variant of the Ahasl1 locus that codes for the acetohydroxyacid synthase, which is the target site of these herbicides. The mechanism of resistance endowed by modifier genes has not been characterized and it could be related to non-target-site resistance. The objective of this study was to evaluate the role of cytochrome P450 monooxygenases (P450s in Imisun resistance. The response to imazapyr herbicide in combination with P450s inhibitor malathion was evaluated in 2 Imisun lines, IMI-1 and RHA426. Malathion reduced herbicide efficacy in both lines, but IMI-1 was affected in a greater extent. A significant reduction in plant growth in response to P450s inhibitors 1-aminobenzotriazole and piperonyl butoxide treatment was detected in the Imisun line HA425. The increased susceptibility to imazapyr after P450s-inhibitor treatment indicates that herbicide metabolism by P450s is a mechanism involved in Imisun resistance. These results also suggest the involvement of different P450s isozymes in endowing resistance to imazapyr in Imisun cultivars.

Measuring the temperature of hot nuclear fragments

International Nuclear Information System (INIS)

Wuenschel, S.; Bonasera, A.; May, L.W.; Souliotis, G.A.; Tripathi, R.; Galanopoulos, S.; Kohley, Z.; Hagel, K.; Shetty, D.V.; Huseman, K.; Soisson, S.N.; Stein, B.C.; Yennello, S.J.

2010-01-01

A new thermometer based on fragment momentum fluctuations is presented. This thermometer exhibited residual contamination from the collective motion of the fragments along the beam axis. For this reason, the transverse direction has been explored. Additionally, a mass dependence was observed for this thermometer. This mass dependence may be the result of the Fermi momentum of nucleons or the different properties of the fragments (binding energy, spin, etc.) which might be more sensitive to different densities and temperatures of the exploding fragments. We expect some of these aspects to be smaller for protons (and/or neutrons); consequently, the proton transverse momentum fluctuations were used to investigate the temperature dependence of the source.

Investigation of the factors affecting the reliability of precision measurement of a liquid helium temperature under its regulation and stabilization in dynamic conditions

International Nuclear Information System (INIS)

Demishev, A.G.; Suplin, V.Z.; Khirnyj, V.F.; Ryazantsev, A.F.; Nemish, I.Yu.

1989-01-01

In the process of regulation and stabilization of liquid helium temperature at the initial stage of pressure increase the effect of advanced temperature increase, indicated by a carcass semiconductor thermometer, and its subsequent jump to the value corresponding to the temperature of liquid at the given moment is revealed. It is shown that irregular peculiarities in the indices of the carcass thermometers do not reflect the actual character of liquid temperature change, but are the consequence of processes taking place on their surfaces. A supposition is made that the peculiarities are determined by mutual effect of heat, released by measurement current in the thermometer, and the process of collapse of gas bubbles adhering to its surface

Resistance to Wheat Curl Mite in Arthropod-Resistant Rye-Wheat Translocation Lines

Directory of Open Access Journals (Sweden)

Lina Maria Aguirre-Rojas

2017-11-01

Full Text Available The wheat curl mite, Aceria toschiella (Keifer, and a complex of viruses vectored by A. toschiella substantially reduce wheat yields in every wheat-producing continent in the world. The development of A. toschiella-resistant wheat cultivars is a proven economically and ecologically viable method of controlling this pest. This study assessed A. toschiella resistance in wheat genotypes containing the H13, H21, H25, H26, H18 and Hdic genes for resistance to the Hessian fly, Mayetiola destructor (Say and in 94M370 wheat, which contains the Dn7 gene for resistance to the Russian wheat aphid, Diuraphis noxia (Kurdjumov. A. toschiella populations produced on plants containing Dn7 and H21 were significantly lower than those on plants of the susceptible control and no different than those on the resistant control. Dn7 resistance to D. noxia and H21 resistance to M. destructor resulted from translocations of chromatin from rye into wheat (H21—2BS/2RL, Dn7—1BL/1RS. These results provide new wheat pest management information, indicating that Dn7 and H21 constitute resources that can be used to reduce yield losses caused by A. toschiella, M. destructor, D. noxia, and wheat streak mosaic virus infection by transferring multi-pest resistance to single sources of germplasm.

Genetic Determinants of High-Level Oxacillin Resistance in Methicillin-Resistant Staphylococcus aureus.

Science.gov (United States)

Pardos de la Gandara, Maria; Borges, Vitor; Chung, Marilyn; Milheiriço, Catarina; Gomes, João Paulo; de Lencastre, Herminia; Tomasz, Alexander

2018-06-01

Methicillin-resistant Staphylococcus aureus (MRSA) strains carry either a mecA - or a mecC -mediated mechanism of resistance to beta-lactam antibiotics, and the phenotypic expression of resistance shows extensive strain-to-strain variation. In recent communications, we identified the genetic determinants associated with the stringent stress response that play a major role in the antibiotic resistant phenotype of the historically earliest "archaic" clone of MRSA and in the mecC -carrying MRSA strain LGA251. Here, we sought to test whether or not the same genetic determinants also contribute to the resistant phenotype of highly and homogeneously resistant (H*R) derivatives of a major contemporary MRSA clone, USA300. We found that the resistance phenotype was linked to six genes ( fruB , gmk , hpt , purB , prsA , and relA ), which were most frequently targeted among the analyzed 20 H*R strains (one mutation per clone in 19 of the 20 H*R strains). Besides the strong parallels with our previous findings (five of the six genes matched), all but one of the repeatedly targeted genes were found to be linked to guanine metabolism, pointing to the key role that this pathway plays in defining the level of antibiotic resistance independent of the clonal type of MRSA. Copyright © 2018 American Society for Microbiology.

Recessive Resistance to Plant Viruses: Potential Resistance Genes Beyond Translation Initiation Factors

Directory of Open Access Journals (Sweden)

Masayoshi Hashimoto

2016-10-01

Full Text Available The ability of plant viruses to propagate their genomes in host cells depends on many host factors. In the absence of an agrochemical that specifically targets plant viral infection cycles, one of the most effective methods for controlling viral diseases in plants is taking advantage of the host plant’s resistance machinery. Recessive resistance is conferred by a recessive gene mutation that encodes a host factor critical for viral infection. It is a branch of the resistance machinery and, as an inherited characteristic, is very durable. Moreover, recessive resistance may be acquired by a deficiency in a negative regulator of plant defense responses, possibly due to the autoactivation of defense signaling. Eukaryotic translation initiation factor (eIF 4E and eIF4G and their isoforms are the most widely exploited recessive resistance genes in several crop species, and they are effective against a subset of viral species. However, the establishment of efficient, recessive resistance-type antiviral control strategies against a wider range of plant viral diseases requires genetic resources other than eIF4Es. In this review, we focus on recent advances related to antiviral recessive resistance genes evaluated in model plants and several crop species. We also address the roles of next-generation sequencing and genome editing technologies in improving plant genetic resources for recessive resistance-based antiviral breeding in various crop species.

Resistance to valproic acid as predictor of treatment resistance in genetic generalized epilepsies

DEFF Research Database (Denmark)

Gesche, Joanna; Khanevski, Marina; Solberg, Carl

2017-01-01

for refractory seizures. Resistance to valproic acid had a specificity of 100% to identify patients with drug resistance and correlated strongly with bad social outcome and seizure burden. Conversely, 21.2% of all patients with refractory seizures according to the ILAE definition later became seizure free...... (mainly with valproic acid). Our data suggest that "drug resistant GGE" must not be declared unless patients were adequately treated with valproic acid, and advocate resistance to valproic acid as a new clinical biomarker for drug-resistant GGE. A PowerPoint slide summarizing this article is available...

Investigation and Treatment of Fusidic Acid Resistance Among Methicillin-Resistant Staphylococcal Isolates from Egypt.

Science.gov (United States)

Abouelfetouh, Alaa; Kassem, Mervat; Naguib, Marwa; El-Nakeeb, Moustafa

2017-01-01

Methicillin resistance among staphylococci isolated from patients in northern Egypt has escalated alarmingly in the past decade. Data about the prevalence of fusidic acid (FA) resistance in Egyptian clinical isolates are limited. This work investigates the prevalence and mechanism of FA resistance among 81 methicillin-resistant staphylococcal isolates from major hospitals of Alexandria, Egypt. Some combinations for treating infections due to resistant isolates were studied. Twenty-six isolates (32.1%) were FA resistant (minimum inhibitory concentrations [MICs] = 2-1,024 μg/ml), and fusB and fusC genes coding for FA resistance were detected in 30.77% and 34.62% of the FA-resistant strains, respectively. One highly resistant isolate, S502 (MIC = 1,024 μg/ml), possessed both genes. Plasmid curing resulted in fusB loss and MIC decrease by 16-64 folds. Conjugation caused acquisition of FA resistance among susceptible isolates. Serial passages in subinhibitory FA concentrations produced mutants with increased MIC by 4-32 folds. The combination of FA with rifampin, gentamicin, or ampicillin/sulbactam, in a subinhibitory concentration, was synergistic against the isolates, including serial passage mutants, decreasing number of survivors by an average of 2-4 logs. A relatively moderate rate of FA resistance was detected in Alexandria hospitals. Combination therapy with gentamicin, rifampin, or ampicillin/sulbactam is crucial to preserve the effectiveness of FA.

Antibiotic Resistance in Foodborne Pathogens

OpenAIRE

Walsh, Ciara; Duffy, Geraldine

2013-01-01

Wide-spread antibiotic resistance among bacterial pathogens is now a serious public health issue and multi-antibiotic resistance has been reported in many foodborne pathogens including Salmonella and E. coli. A study to determine antibiotic resistance profiles of a range of Salmonella and Verocytotoxigenic E.coli (VTEC) isolated from Irish foods revealed significant levels of antibiotic resistance in the strains. S. typhimurium DT104 were multiantibiotic resistant with 97% resistant to 7 anti...

Hydraulic resistance of biofilms

KAUST Repository

Dreszer, C.; Vrouwenvelder, Johannes S.; Paulitsch-Fuchs, Astrid H.; Zwijnenburg, Arie; Kruithof, Joop C.; Flemming, Hans Curt

2013-01-01

resistance is very low compared to the expected biofilm resistance and, thus, biofilm resistance can be determined accurately. Transmembrane pressure drop was monitored. As biofilm parameters, thickness, total cell number, TOC, and extracellular polymeric

Experimental Studies on the Changes in Resistivity and Its Anisotropy Using Electrical Resistivity Tomography

Directory of Open Access Journals (Sweden)

Tao Zhu

2012-01-01

Full Text Available Three measuring lines were arranged on one of free planes of magnetite cuboid samples. Apparent resistivity data were acquired by MIR-2007 resistivity meter when samples were under uniaxial compression of servocontrol YAW-5000F loadingmachine in laboratory. Then we constructed the residual resistivity images using electrical resistivity tomography (ERT and plotted the diagrams of apparent resistivity anisotropy coefficient (ARAC λ∗ and the included angle α between the major axis of apparent resistivity anisotropy ellipse and the axis of load with pressure and effective depth. Our results show that with increasing pressure, resistivity and the decreased (D region and increased (I region resistivity regions have complex behaviors, but when pressure is higher than a certain value, the average resistivity decrease and the area of D region expand gradually in all time with the increase of pressure, which may be significant to the monitoring and prediction of earthquake, volcanic activities, and large-scale geologic motions. The effects of pressure on λ∗ and α are not very outstanding for dry magnetite samples.

Selection for chlorpyrifos resistance in Liriomyza sativae Blanchard: Cross-resistance patterns, stability and biochemical mechanisms.

Science.gov (United States)

Askari-Saryazdi, Ghasem; Hejazi, Mir Jalil; Ferguson, J Scott; Rashidi, Mohammad-Reza

2015-10-01

The vegetable leafminer (VLM), Liriomyza sativae (Diptera: Agromyzidae) is a serious pest of vegetable crops and ornamentals worldwide. In cropping systems with inappropriate management strategies, development of resistance to insecticides in leafminers is probable. Chlorpyrifos is a commonly used pesticide for controlling leafminers in Iran, but resistance to this insecticide in leafminers has not been characterized. In order to develop strategies to minimize resistance in the field and greenhouse, a laboratory selected chlorpyrifos resistant strain of L. sativae was used to characterize resistance and determine the rate of development and stability of resistance. Selecting for resistance in the laboratory after 23 generations yielded a chlorpyrifos resistant selected strain (CRSS) with a resistance ratio of 40.34, determined on the larval stage. CRSS exhibited no cross-resistance to other tested insecticides except for diazinon. Synergism and biochemical assays indicated that esterases (EST) had a key role in metabolic resistance to chlorpyrifos, but glutathione S-transferase (GST) and mixed function oxidase (MFO) were not mediators in this resistance. In CRSS acetylcholinesterase (AChE) was more active than the susceptible strain, Sharif (SH). AChE in CRSS was also less sensitive to inhibition by propoxur. The kinetics parameters (Km and Vmax) of AChE indicated that affinities and hydrolyzing efficiencies of this enzyme in CRSS were higher than SH. Susceptibility to chlorpyrifos in L. sativae was re-gained in the absence of insecticide pressure. Synergism, biochemical and cross-resistance assays revealed that overactivity of metabolic enzymes and reduction in target site sensitivity are probably joint factors in chlorpyrifos resistance. An effective insecticide resistance management program is necessary to prevent fast resistance development in crop systems. Copyright © 2015 Elsevier Inc. All rights reserved.

Study of thermal effects in superconducting RF cavities; Etude des effets thermiques dans le cavites supraconductrices

Energy Technology Data Exchange (ETDEWEB)

Bousson, S.; Caruette, A.; Fouaidy, M.; Hammoudi, N.; Junquera, T.; Lesrel, J.; Yaniche, J.F. [Services Techniques, Inst. de Physique Nucleaire, Paris-11 Univ., 91 - Orsay (France)

1999-11-01

A high speed thermometric system equipped with 64 fixed surface thermometers is used to investigate thermal effects in several 3 GHz cavities. An evaluation of the time response of our thermometers is presented. A method based on RF signal analysis is proposed to evaluate the normal zone propagation rate during thermal breakdown. (authors) 2 refs., 3 figs.

Resistance of Bacteria to Biocides.

Science.gov (United States)

Maillard, Jean-Yves

2018-04-01

Biocides and formulated biocides are used worldwide for an increasing number of applications despite tightening regulations in Europe and in the United States. One concern is that such intense usage of biocides could lead to increased bacterial resistance to a product and cross-resistance to unrelated antimicrobials including chemotherapeutic antibiotics. Evidence to justify such a concern comes mostly from the use of health care-relevant bacterial isolates, although the number of studies of the resistance characteristics of veterinary isolates to biocides have increased the past few years. One problem remains the definition of "resistance" and how to measure resistance to a biocide. This has yet to be addressed globally, although the measurement of resistance is becoming more pressing, with regulators both in Europe and in the United States demanding that manufacturers provide evidence that their biocidal products will not impact on bacterial resistance. Alongside in vitro evidence of potential antimicrobial cross-resistance following biocide exposure, our understanding of the mechanisms of bacterial resistance and, more recently, our understanding of the effect of biocides to induce a mechanism(s) of resistance in bacteria has improved. This article aims to provide an understanding of the development of antimicrobial resistance in bacteria following a biocide exposure. The sections provide evidence of the occurrence of bacterial resistance and its mechanisms of action and debate how to measure bacterial resistance to biocides. Examples pertinent to the veterinary field are used where appropriate.

Systematic drug screening reveals specific vulnerabilities and co-resistance patterns in endocrine-resistant breast cancer.

Science.gov (United States)

Kangaspeska, Sara; Hultsch, Susanne; Jaiswal, Alok; Edgren, Henrik; Mpindi, John-Patrick; Eldfors, Samuli; Brück, Oscar; Aittokallio, Tero; Kallioniemi, Olli

2016-07-04

The estrogen receptor (ER) inhibitor tamoxifen reduces breast cancer mortality by 31 % and has served as the standard treatment for ER-positive breast cancers for decades. However, 50 % of advanced ER-positive cancers display de novo resistance to tamoxifen, and acquired resistance evolves in 40 % of patients who initially respond. Mechanisms underlying resistance development remain poorly understood and new therapeutic opportunities are urgently needed. Here, we report the generation and characterization of seven tamoxifen-resistant breast cancer cell lines from four parental strains. Using high throughput drug sensitivity and resistance testing (DSRT) with 279 approved and investigational oncology drugs, exome-sequencing and network analysis, we for the first time, systematically determine the drug response profiles specific to tamoxifen resistance. We discovered emerging vulnerabilities towards specific drugs, such as ERK1/2-, proteasome- and BCL-family inhibitors as the cells became tamoxifen-resistant. Co-resistance to other drugs such as the survivin inhibitor YM155 and the chemotherapeutic agent paclitaxel also occurred. This study indicates that multiple molecular mechanisms dictate endocrine resistance, resulting in unexpected vulnerabilities to initially ineffective drugs, as well as in emerging co-resistances. Thus, combatting drug-resistant tumors will require patient-tailored strategies in order to identify new drug vulnerabilities, and to understand the associated co-resistance patterns.

Camptothecin resistance

DEFF Research Database (Denmark)

Brangi, M; Litman, Thomas; Ciotti, M

1999-01-01

. Glucuronides were found at equal levels in both parental and resistant colon cancer cell lines for epirubicin and to a lesser extent for SN-38 and mitoxantrone. Low levels of glucuronidation could also be detected in the resistant breast cancer cells. These results were confirmed by analysis of the UGT1A...

Regicide and Resistance

DEFF Research Database (Denmark)

Flohr, Mikkel

2016-01-01

This article examines the role of resistance in Michel Foucault’s political thought. The article recovers this otherwise obscured aspect of Foucault’s thought through a systematic analysis of his theoretical regicide and consequent reconceptualization of power, agency and resistance. It is argued...... that Foucault developed a highly original account of resistance, which was, and should continue to be considered, central to his thought and its critical potential. It is shown how Foucault’s concept of resistance overcomes the limitation of voluntarism and determinism, which continue to mare contemporary...... political theory, providing a passage from the critique of contemporary configurations of power to the irrepressible possibility that they may be contested and changed....

The effect of electrode contact resistance and capacitive coupling on Complex Resistivity measurements

DEFF Research Database (Denmark)

Ingeman-Nielsen, Thomas

2006-01-01

The effect of electrode contact resistance and capacitive coupling on complex resistivity (CR) measurements is studied in this paper. An equivalent circuit model for the receiver is developed to describe the effects. The model shows that CR measurements are severely affected even at relatively lo...... with the contact resistance artificially increased by resistors. The results emphasize the importance of keeping contact resistance low in CR measurements....

Animation of Antimicrobial Resistance

Medline Plus

Full Text Available ... Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing options ... produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over time, ...

Animation of Antimicrobial Resistance

Medline Plus

Full Text Available ... Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing ... CVM) produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over ...

Phenotypic Resistance to Antibiotics

Directory of Open Access Journals (Sweden)

Jose L. Martinez

2013-04-01

Full Text Available The development of antibiotic resistance is usually associated with genetic changes, either to the acquisition of resistance genes, or to mutations in elements relevant for the activity of the antibiotic. However, in some situations resistance can be achieved without any genetic alteration; this is called phenotypic resistance. Non-inherited resistance is associated to specific processes such as growth in biofilms, a stationary growth phase or persistence. These situations might occur during infection but they are not usually considered in classical susceptibility tests at the clinical microbiology laboratories. Recent work has also shown that the susceptibility to antibiotics is highly dependent on the bacterial metabolism and that global metabolic regulators can modulate this phenotype. This modulation includes situations in which bacteria can be more resistant or more susceptible to antibiotics. Understanding these processes will thus help in establishing novel therapeutic approaches based on the actual susceptibility shown by bacteria during infection, which might differ from that determined in the laboratory. In this review, we discuss different examples of phenotypic resistance and the mechanisms that regulate the crosstalk between bacterial metabolism and the susceptibility to antibiotics. Finally, information on strategies currently under development for diminishing the phenotypic resistance to antibiotics of bacterial pathogens is presented.

Resistance and Resistant Reaction of Gossypium arboreum to the Reniform, Nematode, Rotylenchulus reniformis

Science.gov (United States)

Carter, William W.

1981-01-01

Gossypium arboreum 'Nanking CB 1402' possessed a high level of resistance to Rotylenchulus reniformis. Within 16 h, the nematode penetrated roots of resistant and susceptible cottons equally. After 36 h, significantly fewer nematodes were found in resistant roots. Larvae fed in either an endodermal or pericyclic cell and had no specificity for root tissue of a particular age. In roots of resistant G. arboreum '1402,' wall breakdown of pericyclic cells was evident after 3 d, endodermal and cortical cells collapsed, and the hypertrophied pericyclic cells disintegrated within 12 d. Cell walls immediately adjacent to the nematode's head were thickened and more safranin positive in resistant than in susceptible cotton cultivars. Several other cultivars of G. arboreum were also resistant to R. reniformis, based on nematode fecundity and percent egg reduction. PMID:19300777

Stability and Repeatability of the Distress Thermometer (DT and the Edmonton Symptom Assessment System-Revised (ESAS-r with Parents of Childhood Cancer Survivors.

Directory of Open Access Journals (Sweden)

Tatsiana Leclair

Full Text Available Parents report psychological distress in association with their child's cancer. Reliable tools are needed to screen parental distress over the cancer trajectory. This study aimed to estimate the stability and repeatability of the Distress Thermometer (DT and the Depression and Anxiety items of the Edmonton Symptom Assessment System-revised (ESAS-r-D; -A in parents of children diagnosed with cancer.Fifty parents (28 mothers, median age = 44 of clinically stable survivors of childhood solid and brain tumours completed questionnaires about their own distress (DT, ESAS-r-D; -A, Brief Symptom Inventory-18: BSI-18, Patient Health Questionnaire-9: PHQ-9, Generalized Anxiety Disorder-7: GAD-7 and their children's quality of life (QoL; Peds Quality of Life: PedsQL twice, with a month interval between the two assessments. At retest, parents also evaluated life events that occurred between the two time points. Hierarchical regressions explored moderators for the temporal stability of test measures.Stability estimates were ICC = .78 for the DT, .55 for the ESAS-r-D, and .47 for the ESAS-r-A. Caseness agreement between test and retest was substantial for the DT, fair for the ESAS-r-D, and slight for the ESAS-r-A. Repeatability analyses indicated that the error range for the DT was more than 2 pts below/above actual measurement, whereas it was more than 3 pts for the ESAS-r-A, and 2.5 for the ESAS-r-D. Instability of the DT could be explained by changes in children's physical QoL, but not by other components of QoL or life events. No moderators of stability could be identified for the ESAS-r items.The DT appears to be a fairly stable measure when the respondent's condition is stable yet with a relatively wide error range. Fluctuations in distress-related constructs may affect the temporal stability of the DT. The lower stability of ESAS-r items may result from shorter time-lapse instructions resulting in a greater sensitivity to change. Findings support

Metabolic Resistance in Bed Bugs

Directory of Open Access Journals (Sweden)

Omprakash Mittapalli

2011-03-01

Full Text Available Blood-feeding insects have evolved resistance to various insecticides (organochlorines, pyrethroids, carbamates, etc. through gene mutations and increased metabolism. Bed bugs (Cimex lectularius are hematophagous ectoparasites that are poised to become one of the major pests in households throughout the United States. Currently, C. lectularius has attained a high global impact status due to its sudden and rampant resurgence. Resistance to pesticides is one factor implicated in this phenomenon. Although much emphasis has been placed on target sensitivity, little to no knowledge is available on the role of key metabolic players (e.g., cytochrome P450s and glutathione S-transferases towards pesticide resistance in C. lectularius. In this review, we discuss different modes of resistance (target sensitivity, penetration resistance, behavioral resistance, and metabolic resistance with more emphasis on metabolic resistance.

Isotope and chemical investigation of geothermal springs and thermal water produced by oil wells in potwat area, Pakistan

International Nuclear Information System (INIS)

Ahmad, M.; Rafique, M.; Tariq, J.A; Choudhry, M.A.; Hussain, Q.M.

2008-10-01

Isotopes and geochemical techniques were applied to investigate the origin, subsurface history and reservoir temperatures of geothermal springs in Potwar. Two sets of water samples were collected. Surface temperatures of geothermal springs ranges from 52 to 68.3 C. Waters produced by oil wells in Potwar area were also investigated. Geothermal springs of Potwar area are Na-HCO/sub 3/ type, while the waters produced by oil wells are Na-Cl and Ca-Cl types. Source of both the categories of water is meteoric water recharged from the outcrops of the formations in the Himalayan foothills. These waters undergo very high /sup 18/O-shift (up to 18%) due to rock-water interaction at higher temperatures. High salinity of the oil field waters is due to dissolution of marine evaporites. Reservoir temperatures of thermal springs determined by the Na-K geo thermometers are in the range of 56-91 deg. C, while Na-K-Ca, Na-K-Mg, Na-K-Ca-Mg and quartz geo thermometers give higher temperatures up to 177 C. Reservoir temperature determined by /sup 18/O(SO/Sub 4/-H/sub 2/O) geo thermometer ranges from 112 to 138 deg. C. There is wide variation in reservoir temperatures (54-297 deg. C) of oil fields estimated by different chemical geo thermometers. Na-K geo thermometer seems more reliable which gives close estimates to real temperature (about 100 deg. C) determined during drilling of oil wells. (author)

Development of an experimental variable temperature set-up for a temperature range from 2.2 K to 325 K for cost-effective temperature sensor calibration

Science.gov (United States)

Pal, Sandip; Kar, Ranjan; Mandal, Anupam; Das, Ananda; Saha, Subrata

2017-05-01

A prototype of a variable temperature insert has been developed in-house as a cryogenic thermometer calibration facility. It was commissioned in fulfilment of the very stringent requirements of the temperature control of the cryogenic system. The calibration facility is designed for calibrating industrial cryogenic thermometers that include a temperature sensor and the wires heat-intercept in the 2.2 K-325 K temperature range. The isothermal section of the calibration block onto which the thermometers are mounted is weakly linked with the temperature control zone mounted with cooling capillary coil and cryogenic heater. The connecting wires of the thermometer are thermally anchored with the support of the temperature insert. The calibration procedure begins once the temperature of the support is stabilized. Homogeneity of the calibration block’s temperature is established both by simulation and by cross-comparison of two calibrated sensors. The absolute uncertainty present in temperature measurement is calculated and found comparable with the measured uncertainty at different temperature points. Measured data is presented in comparison to the standard thermometers at fixed points and it is possible to infer that the absolute accuracy achieved is better than  ±0.5% of the reading in comparison to the fixed point temperature. The design and development of simpler, low cost equipment, and approach to analysis of the calibration results are discussed further in this paper, so that it can be easily devised by other researchers.

Molecular Detection of Antimicrobial Resistance

Science.gov (United States)

Fluit, Ad C.; Visser, Maarten R.; Schmitz, Franz-Josef

2001-01-01

The determination of antimicrobial susceptibility of a clinical isolate, especially with increasing resistance, is often crucial for the optimal antimicrobial therapy of infected patients. Nucleic acid-based assays for the detection of resistance may offer advantages over phenotypic assays. Examples are the detection of the methicillin resistance-encoding mecA gene in staphylococci, rifampin resistance in Mycobacterium tuberculosis, and the spread of resistance determinants across the globe. However, molecular assays for the detection of resistance have a number of limitations. New resistance mechanisms may be missed, and in some cases the number of different genes makes generating an assay too costly to compete with phenotypic assays. In addition, proper quality control for molecular assays poses a problem for many laboratories, and this results in questionable results at best. The development of new molecular techniques, e.g., PCR using molecular beacons and DNA chips, expands the possibilities for monitoring resistance. Although molecular techniques for the detection of antimicrobial resistance clearly are winning a place in routine diagnostics, phenotypic assays are still the method of choice for most resistance determinations. In this review, we describe the applications of molecular techniques for the detection of antimicrobial resistance and the current state of the art. PMID:11585788

Animation of Antimicrobial Resistance

Medline Plus

Full Text Available ... Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin it More sharing options ... CVM) produced a nine-minute animation explaining how antimicrobial resistance both emerges and proliferates among bacteria. Over time, ...

Fate of antibiotic resistant bacteria and genes during wastewater chlorination: implication for antibiotic resistance control.

Directory of Open Access Journals (Sweden)

Qing-Bin Yuan

Full Text Available This study investigated fates of nine antibiotic-resistant bacteria as well as two series of antibiotic resistance genes in wastewater treated by various doses of chlorine (0, 15, 30, 60, 150 and 300 mg Cl2 min/L. The results indicated that chlorination was effective in inactivating antibiotic-resistant bacteria. Most bacteria were inactivated completely at the lowest dose (15 mg Cl2 min/L. By comparison, sulfadiazine- and erythromycin-resistant bacteria exhibited tolerance to low chlorine dose (up to 60 mg Cl2 min/L. However, quantitative real-time PCRs revealed that chlorination decreased limited erythromycin or tetracycline resistance genes, with the removal levels of overall erythromycin and tetracycline resistance genes at 0.42 ± 0.12 log and 0.10 ± 0.02 log, respectively. About 40% of erythromycin-resistance genes and 80% of tetracycline resistance genes could not be removed by chlorination. Chlorination was considered not effective in controlling antimicrobial resistance. More concern needs to be paid to the potential risk of antibiotic resistance genes in the wastewater after chlorination.

Hydraulic resistance of biofilms

KAUST Repository

Dreszer, C.

2013-02-01

Biofilms may interfere with membrane performance in at least three ways: (i) increase of the transmembrane pressure drop, (ii) increase of feed channel (feed-concentrate) pressure drop, and (iii) increase of transmembrane passage. Given the relevance of biofouling, it is surprising how few data exist about the hydraulic resistance of biofilms that may affect the transmembrane pressure drop and membrane passage. In this study, biofilms were generated in a lab scale cross flow microfiltration system at two fluxes (20 and 100Lm-2h-1) and constant cross flow (0.1ms-1). As a nutrient source, acetate was added (1.0mgL-1 acetate C) besides a control without nutrient supply. A microfiltration (MF) membrane was chosen because the MF membrane resistance is very low compared to the expected biofilm resistance and, thus, biofilm resistance can be determined accurately. Transmembrane pressure drop was monitored. As biofilm parameters, thickness, total cell number, TOC, and extracellular polymeric substances (EPS) were determined, it was demonstrated that no internal membrane fouling occurred and that the fouling layer actually consisted of a grown biofilm and was not a filter cake of accumulated bacterial cells. At 20Lm-2h-1 flux with a nutrient dosage of 1mgL-1 acetate C, the resistance after 4 days reached a value of 6×1012m-1. At 100Lm-2h-1 flux under the same conditions, the resistance was 5×1013m-1. No correlation of biofilm resistance to biofilm thickness was found; Biofilms with similar thickness could have different resistance depending on the applied flux. The cell number in biofilms was between 4×107 and 5×108 cellscm-2. At this number, bacterial cells make up less than a half percent of the overall biofilm volume and therefore did not hamper the water flow through the biofilm significantly. A flux of 100Lm-2h-1 with nutrient supply caused higher cell numbers, more biomass, and higher biofilm resistance than a flux of 20Lm-2h-1. However, the biofilm thickness

Cross-resistance and biochemical mechanisms of resistance to indoxacarb in the diamondback moth, Plutella xylostella.

Science.gov (United States)

Zhang, Shuzhen; Zhang, Xiaolei; Shen, Jun; Li, Dongyang; Wan, Hu; You, Hong; Li, Jianhong

2017-08-01

Indoxacarb belongs to a class of insecticides known as oxadiazines and is the first commercialized pyrazoline-type voltage-dependent sodium channel blocker. A moderate level of resistance to indoxacarb has evolved in field populations of Plutella xylostella from Central China. In the present study, cross-resistance, resistance stability and metabolic mechanisms of indoxacarb resistance were investigated in this moth species. A P. xylostella strain with a high level of resistance to indoxacarb was obtained through continuous selection in the laboratory. The strain showed cross-resistance to metaflumizone, beta-cypermethrin and chlorfenapyr, but no resistance to cyantraniliprole, chlorantraniliprole, abamectin, chlorfluazuron, spinosad and diafenthiuron compared with the susceptible strain. Synergism tests revealed that piperonyl butoxide (PBO) (synergistic ratio, SR=7.8) and diethyl maleate (DEF) (SR=3.5) had considerable synergistic effects on indoxacarb toxicity in the resistant strain (F 58 ). Enzyme activity data showed there was an approximate 5.8-fold different in glutathione S-transferase (GST) and a 6.8-fold different in cytochrome P450 monooxygenase between the resistant strain (F 58 ) and susceptible strain, suggesting that the increased activity of these two enzymes is likely the main detoxification mechanism responsible for the species' resistance to indoxacarb. These results will be helpful for insecticide resistance management strategies to delay the development of indoxacarb resistance in fields. Copyright © 2017. Published by Elsevier Inc.

Multi-Electrode Resistivity Probe for Investigation of Local Temperature Inside Metal Shell Battery Cells via Resistivity: Experiments and Evaluation of Electrical Resistance Tomography

Directory of Open Access Journals (Sweden)

Xiaobin Hong

2015-01-01

Full Text Available Direct Current (DC electrical resistivity is a material property that is sensitive to temperature changes. In this paper, the relationship between resistivity and local temperature inside steel shell battery cells (two commercial 10 Ah and 4.5 Ah lithium-ion cells is innovatively studied by Electrical Resistance Tomography (ERT. The Schlumberger configuration in ERT is applied to divide the cell body into several blocks distributed in different levels, where the apparent resistivities are measured by multi-electrode surface probes. The investigated temperature ranges from −20 to 80 °C. Experimental results have shown that the resistivities mainly depend on temperature changes in each block of the two cells used and the function of the resistivity and temperature can be fitted to the ERT-measurement results in the logistical-plot. Subsequently, the dependence of resistivity on the state of charge (SOC is investigated, and the SOC range of 70%–100% has a remarkable impact on the resistivity at low temperatures. The proposed approach under a thermal cool down regime is demonstrated to monitor the local transient temperature.

Oxidation-resistant cermet

Science.gov (United States)

Phillips, W. M.

1977-01-01

Chromium metal alloys and chromium oxide ceramic are combined to produce cermets with oxidation-resistant properties. Application of cermets includes use in hot corrosive environments requiring strong resistive materials.

Low Prevalence of Carbapenem-Resistant Bacteria in River Water: Resistance Is Mostly Related to Intrinsic Mechanisms.

Science.gov (United States)

Tacão, Marta; Correia, António; Henriques, Isabel S

2015-10-01

Carbapenems are last-resort antibiotics to handle serious infections caused by multiresistant bacteria. The incidence of resistance to these antibiotics has been increasing and new resistance mechanisms have emerged. The dissemination of carbapenem resistance in the environment has been overlooked. The main goal of this research was to assess the prevalence and diversity of carbapenem-resistant bacteria in riverine ecosystems. The presence of frequently reported carbapenemase-encoding genes was inspected. The proportion of imipenem-resistant bacteria was on average 2.24 CFU/ml. Imipenem-resistant strains (n=110) were identified as Pseudomonas spp., Stenotrophomonas maltophilia, Aeromonas spp., Chromobacterium haemolyticum, Shewanella xiamenensis, and members of Enterobacteriaceae. Carbapenem-resistant bacteria were highly resistant to other beta-lactams such as quinolones, aminoglycosides, chloramphenicol, tetracyclines, and sulfamethoxazole/trimethoprim. Carbapenem resistance was mostly associated with intrinsically resistant bacteria. As intrinsic resistance mechanisms, we have identified the blaCphA gene in 77.3% of Aeromonas spp., blaL1 in all S. maltophilia, and blaOXA-48-like in all S. xiamenensis. As acquired resistance mechanisms, we have detected the blaVIM-2 gene in six Pseudomonas spp. (5.45%). Integrons with gene cassettes encoding resistance to aminoglycosides (aacA and aacC genes), trimethoprim (dfrB1b), and carbapenems (blaVIM-2) were found in Pseudomonas spp. Results suggest that carbapenem resistance dissemination in riverine ecosystems is still at an early stage. Nevertheless, monitoring these aquatic compartments for the presence of resistance genes and its host organisms is essential to outline strategies to minimize resistance dissemination.

Antimicrobial resistance of thermophilic Campylobacter

DEFF Research Database (Denmark)

Aarestrup, Frank Møller; Engberg, J.

2001-01-01

Campylobacter has become the leading cause of zoonotic enteric infections in developed and developing countries world-wide. Antimicrobial resistance has emerged among Campylobacter mainly as a consequence of the use of antimicrobial agents in food animal production. Resistance to drugs of choice...... for the treatment of infections, macrolides and fluoroquinolones has emerged as a clinical problem and interventions to reduce this are recommended. Resistance to fluoroquinolones and macrolides is mediated by chromosomal mutations. Resistance to other relevant antimicrobial agents, mediated by acquired resistance...... genes, has not become widespread so far. However, resistance genes originating from both Gram-positive and Gram-negative bacterial species have been found, showing the potential for acquired resistance to emerge in Campylobacter....

Resistance patterns and trends of extensively drug-resistant tuberculosis: 5-year experience

Directory of Open Access Journals (Sweden)

Amresh Kumar Singh

2013-12-01

Full Text Available Objective:Extensively drug-resistant tuberculosis (XDR-TB strains were emerged when multidrug-resistant TB (MDR- TB was inadequately treated. Inadequate treatment of MDR-TB cases may result in additional resistance especially non-XDR-TB and then XDR-TB. The aim of this study was to know the prevalence, resistance patterns and trends of the XDR-TB strains among the MDR-TB at a tertiary care hospital in Lucknow, India Methods: A total of 430 Mycobacterium isolates were underwent NAP test and TB MPT64 Ag test for the identification of Mycobacterium tuberculosis complex (MTBC. Drug-susceptibility test (DST was performed over MTBC for the first line drugs by 1% proportion method (Bactec and for the second-line drugs by 1% proportion method (Lowenstein- Jensen media. The XDR-TB status was further confirmed by line probe assay (GenoType® MTBDRsl assay. Results: Among the 430 isolates of mycobacterium, 365 (84.9% were MTBC and 139 (38.1% were MDR-TB respectively. Further 97 MDR-TB from “highly suspected drug resistant-TB (DR-TB” cases among MDR-TB were tested with second line drugs in which 15 (15.5% XDR-TB and 82 (84.5% were non-XDR-TB. Regarding XDR-TB status, using the 1% proportion method a 100% agreement was seen with the GenoType® MTBDRsl assay. Resistance patterns of XDR-TB were as; 10/15 (66.7% as isoniazid + rifampicin + ciprofloxacin + amikacin resistance and 5/15 (33.3% as isoniazid + rifampicin + ciprofloxacin + amikacin + kanamycin resistance. Conclusion:The prevalence of XDR-TB was 15.5% among MDR-TB. Hence laboratory testing of “highly suspected drug resistant-TB” isolates should be done for both first and second line drugs simultaneously especially in developing countries.J Microbiol Infect Dis 2013;3(4: 169-175

Challenges to Resistance Welding

DEFF Research Database (Denmark)

Song, Quanfeng

This report originates from the compulsory defense during my Ph.D. study at the Technical University of Denmark. Resistance welding is an old and well-proven technology. Yet the emergence of more and more new materials, new designs, invention off new joining techniques, and more stringent...... requirement in quality have imposed challenges to the resistance welding. More some research and development have to be done to adapt the old technology to the manufacturing industry of the 21st century. In the 1st part of the report, the challenging factors to the resistance welding are reviewed. Numerical...... simulation of resistance welding has been under development for many years. Yet it is no easy to make simulation results reliable and accurate because of the complexity of resistance welding process. In the 2nd part of the report numerical modeling of resistance welding is reviewed, some critical factors...

Method of separate determination of high-ohmic sample resistance and contact resistance

Directory of Open Access Journals (Sweden)

Vadim A. Golubiatnikov

2015-09-01

Full Text Available A method of separate determination of two-pole sample volume resistance and contact resistance is suggested. The method is applicable to high-ohmic semiconductor samples: semi-insulating gallium arsenide, detector cadmium-zinc telluride (CZT, etc. The method is based on near-contact region illumination by monochromatic radiation of variable intensity from light emitting diodes with quantum energies exceeding the band gap of the material. It is necessary to obtain sample photo-current dependence upon light emitting diode current and to find the linear portion of this dependence. Extrapolation of this linear portion to the Y-axis gives the cut-off current. As the bias voltage is known, it is easy to calculate sample volume resistance. Then, using dark current value, one can determine the total contact resistance. The method was tested for n-type semi-insulating GaAs. The contact resistance value was shown to be approximately equal to the sample volume resistance. Thus, the influence of contacts must be taken into account when electrophysical data are analyzed.

Operating results obtained in a nuclear power plant with a sensor surveillance prototype

International Nuclear Information System (INIS)

Jacquot, J.P.; Poujol, A.; Beaubatie, J.; Ciaramitaro, W.

1983-03-01

Surveillance methods have been validated and specific equipment have been built to measure the response time of sensors from a nuclear power plant protection channel. The reason of the choice of this parameter is twofold: the sensor response time is representative of the sensor physical status and is also part of the overall channel response time. Two surveillance methods are used: noise analysis (by AR or PSD modeling), and loop current step response (for resistance thermometer detectors only). The methods were validated on test facilities and on nuclear power plants. Two test equipments were built and tested on plants. Results are represented and conclusions are drawn on the feasibility of such methods for sensor surveillance [fr

Efflux-mediated antimicrobial resistance.

Science.gov (United States)

Poole, Keith

2005-07-01

Antibiotic resistance continues to plague antimicrobial chemotherapy of infectious disease. And while true biocide resistance is as yet unrealized, in vitro and in vivo episodes of reduced biocide susceptibility are common and the history of antibiotic resistance should not be ignored in the development and use of biocidal agents. Efflux mechanisms of resistance, both drug specific and multidrug, are important determinants of intrinsic and/or acquired resistance to these antimicrobials, with some accommodating both antibiotics and biocides. This latter raises the spectre (as yet generally unrealized) of biocide selection of multiple antibiotic-resistant organisms. Multidrug efflux mechanisms are broadly conserved in bacteria, are almost invariably chromosome-encoded and their expression in many instances results from mutations in regulatory genes. In contrast, drug-specific efflux mechanisms are generally encoded by plasmids and/or other mobile genetic elements (transposons, integrons) that carry additional resistance genes, and so their ready acquisition is compounded by their association with multidrug resistance. While there is some support for the latter efflux systems arising from efflux determinants of self-protection in antibiotic-producing Streptomyces spp. and, thus, intended as drug exporters, increasingly, chromosomal multidrug efflux determinants, at least in Gram-negative bacteria, appear not to be intended as drug exporters but as exporters with, perhaps, a variety of other roles in bacterial cells. Still, given the clinical significance of multidrug (and drug-specific) exporters, efflux must be considered in formulating strategies/approaches to treating drug-resistant infections, both in the development of new agents, for example, less impacted by efflux and in targeting efflux directly with efflux inhibitors.

Antimicrobial resistance 1979-2009 at Karolinska hospital, Sweden: normalized resistance interpretation during a 30-year follow-up on Staphylococcus aureus and Escherichia coli resistance development.

Science.gov (United States)

Kronvall, Göran

2010-09-01

To utilize a material of inhibition zone diameter measurements from disc diffusion susceptibility tests between 1979 and 2009, an objective setting of epidemiological breakpoints was necessary because of methodological changes. Normalized resistance interpretation (NRI) met this need and was applied to zone diameter histograms for Staphylococcus aureus and Escherichia coli isolates. The results confirmed a slow resistance development as seen in Northern countries. The S. aureus resistance levels for erythromycin, clindamycin and fusidic acid in 2009 were 3.2%, 1.8% and 1.4% with denominator correction. A rise in resistance to four antimicrobials in 1983 was probably because of a spread of resistant Methicillin Susceptible Staphylococcus Aureus (MSSA). For E. coli, the denominator-corrected resistance levels in 2009 were 27% for ampicillin, around 3% for third-generation cephalosporins, 0.1% for imipenem, 2.5% for gentamicin, 19% for trimethoprim, 4.5% for co-trimoxazole, 1.2% for nitrofurantoin and 9% for ciprofloxacin. The temporal trends showed a rise in fluoroquinolone resistance from 1993, a parallel increase in gentamicin resistance, a substantial increase in trimethoprim and sulphonamide resistance in spite of decreased consumption, and a steady rise in ampicillin resistance from a constant level before 1989. A short review of global resistance surveillance studies is included.

Antibiotic resistance in animals.

Science.gov (United States)

Barton, Mary D; Pratt, Rachael; Hart, Wendy S

2003-01-01

There is currently no systematic surveillance or monitoring of antibiotic resistance in Australian animals. Registration of antibiotics for use in animals is tightly controlled and has been very conservative. Fluoroquinolones have not been registered for use in food producing animals and other products have been removed from the market because of human health concerns. In the late 1970s, the Animal Health Committee coordinated a survey of resistance in Salmonella and Escherichia coli isolates from cattle, pigs and poultry and in bovine Staphylococcus aureus. Some additional information is available from published case reports. In samples collected prior to the withdrawal of avoparcin from the market, no vancomycin resistant Enterococcus faecium or Enterococcus faecalis were detected in samples collected from pigs, whereas some vanA enterococci, including E. faecium and E. faecalis, were found in chickens. No vanB enterococci were detected in either species. Virginiamycin resistance was common in both pig and poultry isolates. Multiple resistance was common in E. coli and salmonellae isolates. No fluoroquinolone resistance was found in salmonellae, E. coli or Campylobacter. Beta-lactamase production is common in isolates from bovine mastitis, but no methicillin resistance has been detected. However, methicillin resistance has been reported in canine isolates of Staphylococcus intermedius and extended spectrum beta-lactamase producing E. coli has been found in dogs.

Systematic drug screening reveals specific vulnerabilities and co-resistance patterns in endocrine-resistant breast cancer

International Nuclear Information System (INIS)

Kangaspeska, Sara; Hultsch, Susanne; Jaiswal, Alok; Edgren, Henrik; Mpindi, John-Patrick; Eldfors, Samuli; Brück, Oscar; Aittokallio, Tero; Kallioniemi, Olli

2016-01-01

The estrogen receptor (ER) inhibitor tamoxifen reduces breast cancer mortality by 31 % and has served as the standard treatment for ER-positive breast cancers for decades. However, 50 % of advanced ER-positive cancers display de novo resistance to tamoxifen, and acquired resistance evolves in 40 % of patients who initially respond. Mechanisms underlying resistance development remain poorly understood and new therapeutic opportunities are urgently needed. Here, we report the generation and characterization of seven tamoxifen-resistant breast cancer cell lines from four parental strains. Using high throughput drug sensitivity and resistance testing (DSRT) with 279 approved and investigational oncology drugs, exome-sequencing and network analysis, we for the first time, systematically determine the drug response profiles specific to tamoxifen resistance. We discovered emerging vulnerabilities towards specific drugs, such as ERK1/2-, proteasome- and BCL-family inhibitors as the cells became tamoxifen-resistant. Co-resistance to other drugs such as the survivin inhibitor YM155 and the chemotherapeutic agent paclitaxel also occurred. This study indicates that multiple molecular mechanisms dictate endocrine resistance, resulting in unexpected vulnerabilities to initially ineffective drugs, as well as in emerging co-resistances. Thus, combatting drug-resistant tumors will require patient-tailored strategies in order to identify new drug vulnerabilities, and to understand the associated co-resistance patterns. The online version of this article (doi:10.1186/s12885-016-2452-5) contains supplementary material, which is available to authorized users

Ciprofloxacin-resistant Escherichia coli in Central Greece: mechanisms of resistance and molecular identification

Directory of Open Access Journals (Sweden)

Mavroidi Angeliki

2012-12-01

Full Text Available Abstract Background Fluoroquinolone resistant E. coli isolates, that are also resistant to other classes of antibiotics, is a significant challenge to antibiotic treatment and infection control policies. In Central Greece a significant increase of ciprofloxacin-resistant Escherichia coli has occurred during 2011, indicating the need for further analysis. Methods A total of 106 ciprofloxacin-resistant out of 505 E. coli isolates consecutively collected during an eight months period in a tertiary Greek hospital of Central Greece were studied. Antimicrobial susceptibility patterns and mechanisms of resistance to quinolones were assessed, whereas selected isolates were further characterized by multilocus sequence typing and β-lactamase content. Results Sequence analysis of the quinolone-resistance determining region of the gyrA and parC genes has revealed that 63% of the ciprofloxacin-resistant E. coli harbored a distinct amino acid substitution pattern (GyrA:S83L + D87N; ParC:S80I + E84V, while 34% and 3% carried the patterns GyrA:S83L + D87N; ParC:S80I and GyrA:S83L + D87N; ParC:S80I + E84G respectively. The aac (6’-1b-cr plasmid-mediated quinolone resistance determinant was also detected; none of the isolates was found to carry the qnrA, qnrB and qnrS. Genotyping of a subset of 35 selected ciprofloxacin-resistant E. coli by multilocus sequence typing has revealed the presence of nine sequence types; ST131 and ST410 were the most prevalent and were exclusively correlated with hospital and health care associated infections, while strains belonging to STs 393, 361 and 162 were associated with community acquired infections. The GyrA:S83L + D87N; ParC:S80I + E84V substitution pattern was found exclusively among ST131 ciprofloxacin-resistant E. coli. Extended-spectrum β-lactamase-positive ST131 ciprofloxacin-resistant isolates produced CTX-M-type enzymes; eight the CTX-M-15 and one the CTX-M-3 variant. CTX-M-1 like and KPC-2 enzymes were detected

Predictable Phenotypes of Antibiotic Resistance Mutations.

Science.gov (United States)

Knopp, M; Andersson, D I

2018-05-15

Antibiotic-resistant bacteria represent a major threat to our ability to treat bacterial infections. Two factors that determine the evolutionary success of antibiotic resistance mutations are their impact on resistance level and the fitness cost. Recent studies suggest that resistance mutations commonly show epistatic interactions, which would complicate predictions of their stability in bacterial populations. We analyzed 13 different chromosomal resistance mutations and 10 host strains of Salmonella enterica and Escherichia coli to address two main questions. (i) Are there epistatic interactions between different chromosomal resistance mutations? (ii) How does the strain background and genetic distance influence the effect of chromosomal resistance mutations on resistance and fitness? Our results show that the effects of combined resistance mutations on resistance and fitness are largely predictable and that epistasis remains rare even when up to four mutations were combined. Furthermore, a majority of the mutations, especially target alteration mutations, demonstrate strain-independent phenotypes across different species. This study extends our understanding of epistasis among resistance mutations and shows that interactions between different resistance mutations are often predictable from the characteristics of the individual mutations. IMPORTANCE The spread of antibiotic-resistant bacteria imposes an urgent threat to public health. The ability to forecast the evolutionary success of resistant mutants would help to combat dissemination of antibiotic resistance. Previous studies have shown that the phenotypic effects (fitness and resistance level) of resistance mutations can vary substantially depending on the genetic context in which they occur. We conducted a broad screen using many different resistance mutations and host strains to identify potential epistatic interactions between various types of resistance mutations and to determine the effect of strain

Organization of a resistance gene cluster linked to rhizomania resistance in sugar beet

Science.gov (United States)

Genetic resistance to rhizomania has been in use for over 40 years. Characterization of the molecular basis for susceptibility and resistance has proved challenging. Nucleotide-binding leucine-rich-repeat-containing (NB-LRR) genes have been implicated in numerous gene-for-gene resistance interaction...

Expected Accuracy when using Non-Calibrated CernoxTM Sensors

CERN Document Server

Casas-Cubillos, J

2012-01-01

Within the ITER-CERN collaboration agreement, task “PROCUREMENT OF CRYOGENIC THERMOMETERS TO MONITOR ITER MAGNETS AND FEEDER TEMPERATURES”, CERN is investigating what would be the expected accuracy when using non-calibrated Cernox™ temperature sensors at 4.2 K. The cernox™ is a resistive type temperature sensor that is capable of measuring the full temperature range of interest for ITER, it is 4.2 K to 300 K. Non-calibrated cernox™ sensors are delivered with a table listing the resistance at the following temperatures: 4.2 K, 77 K and 300 K. CERN has deployed several thousands of individually calibrated cernox™ sensors and they are used to compare the manufacturer data at 4.2 K with their individual calibration performed by CERN. Within a sample size of 5’941 sensors, 99.39% of the population is able to provide a measurement within +/-0.1 K at 4.2 well within the requirements at low temperature specified by ITER.

Glyphosate-Resistant Goosegrass from Mississippi

Directory of Open Access Journals (Sweden)

Vijay K. Nandula

2013-05-01

Full Text Available A suspected glyphosate-resistant goosegrass [Eleusine indica (L. Gaertn.] population, found in Washington County, Mississippi, was studied to determine the level of resistance and whether the resistance was due to a point mutation, as was previously identified in a Malaysian population. Whole plant dose response assays indicated a two- to four-fold increase in resistance to glyphosate. Leaf disc bioassays based on a glyphosate-dependent increase in shikimate levels indicated a five- to eight-fold increase in resistance. Sequence comparisons of messenger RNA for epsps, the gene encoding the enzyme 5-enolpyruvylshikimate-3-phosphate synthase, from resistant and sensitive goosegrass, revealed a cytosine to thymine nucleotide change at position 319 in the resistant accessions. This single nucleotide polymorphism causes a proline to serine amino acid substitution at position 106 in 5-enolpyruvylshikimate-3-phosphate synthase. A real-time polymerase chain reaction assay using DNA probes specific for the nucleotide change at position 319 was developed to detect this polymorphism. Goosegrass from 42 locations were screened, and the results indicated that glyphosate-resistant goosegrass remained localized to where it was discovered. Pendimethalin, s-metolachlor, clethodim, paraquat and fluazifop controlled resistant goosegrass 93% to 100%, indicating that several control options for glyphosate-resistant goosegrass are available.

Radiation thermometry for semiconductor crystal growing furnaces

International Nuclear Information System (INIS)

Helgeland, W.

1985-01-01

Single crystals of silicon produced by the Czochralski process are used widely in the production of integrated circuits and other electronic devices. Recent advances in automation of industrial equipment for this process have led to the application of a dual wave band radiation thermometer. The instrument system automatically performs certain critical temperature measurements. In nonautomated equipment, these measurements require the judgement of a trained human operator. The difficulties of measuring and controlling the temperature at the critical location are discussed, especially with regard to detecting the meltdown end point and to initially establishing the correct temperature for seeding. A description is given of the customized temperature measurement system, which is based upon an existing ratio radiation thermometer. Thermometer output characteristics are described

Treatment Options for Carbapenem-Resistant and Extensively Drug-Resistant Acinetobacter baumannii Infections

Science.gov (United States)

Viehman, J. Alexander; Nguyen, Minh-Hong; Doi, Yohei

2014-01-01

Acinetobacter baumannii is a leading cause of healthcare-associated infections worldwide. Due to various intrinsic and acquired mechanisms of resistance, most β-lactam agents are not effective against many strains, and carbapenems have played an important role in therapy. Recent trends show many infections are caused by carbapenem-resistant, or even extensively drug-resistant (XDR) strains, for which effective therapy is not well established. Evidence to date suggests that colistin constitutes the backbone of therapy, but the unique pharmacokinetic properties of colistin have led many to suggest the use of combination antimicrobial therapy. However, the combination of agents and dosing regimens that delivers the best clinical efficacy while minimizing toxicity is yet to be defined. Carbapenems, sulbactam, rifampin and tigecycline have been the most studied in the context of combination therapy. Most data regarding therapy for invasive, resistant A. baumannii infections come from uncontrolled case series and retrospective analyses, though some clinical trials have been completed and others are underway. Early institution of appropriate antimicrobial therapy is shown to consistently improve survival of patients with carbapenem-resistant and XDR A. baumannii infection, but the choice of empiric therapy in these infections remains an open question. This review summarizes the most current knowledge regarding the epidemiology, mechanisms of resistance, and treatment considerations of carbapenem-resistant and XDR A. baumannii. PMID:25091170

Biological improvement of radiation resistance

Energy Technology Data Exchange (ETDEWEB)

Chun, K J; Lee, Y K; Kim, J S; Kim, J K; Lee, S J

2000-08-01

To investigate the mechanisms of gene action related to the radiation resistance in microorganisms could be essentially helpful for the development of radiation protectants and hormeric effects of low dose radiation. This book described isolation of radiation-resistant microorganisms, induction of radiation-resistant and functionally improved mutants by gamma-ray radiation, cloning and analysis of the radiation resistance related genes and analysis of the expressed proteins of the radiation resistant related genes.

Biological improvement of radiation resistance

International Nuclear Information System (INIS)

Chun, K. J.; Lee, Y. K.; Kim, J. S.; Kim, J. K.; Lee, S. J.

2000-08-01

To investigate the mechanisms of gene action related to the radiation resistance in microorganisms could be essentially helpful for the development of radiation protectants and hormeric effects of low dose radiation. This book described isolation of radiation-resistant microorganisms, induction of radiation-resistant and functionally improved mutants by gamma-ray radiation, cloning and analysis of the radiation resistance related genes and analysis of the expressed proteins of the radiation resistant related genes

Biotechnology: herbicide-resistant crops

Science.gov (United States)

Transgenic, herbicide-resistant (HR) crops are planted on about 80% of the land covered by transgenic crops. More than 90% of HR crios are glyphosate-resistant (GR) crops, the others being resistant to glufosinate. The wide-scale adoption of HR crops, largely for economic reasons, has been the mos...

Resistance in Everyday Life

DEFF Research Database (Denmark)

This book is about resistance in everyday life, illustrated through empirical contexts from different parts of the world. Resistance is a widespread phenomenon in biological, social and psychological domains of human cultural development. Yet, it is not well articulated in the academic literature....... The contributors deal with strategies for handling dissent by individuals or groups, specifically dissent through resistance. Resistance can be a location of intense personal, interpersonal and cultural negotiation, and that is the primary reason for interest in this phenomenon. Ordinary life events contain...

Resistent tuberkulose i Danmark

DEFF Research Database (Denmark)

Thomsen, V O; Johansen, I S; Bauer, J O

2001-01-01

INTRODUCTION: Increased rates of multidrug-resistant (MDR) tuberculosis (TB) has been reported from countries close to Denmark. We evaluated the incidence of drug resistance in Denmark in order to determine the magnitude of the problem. MATERIALS AND METHODS: Susceptibility testing was performed......-cluster. Among all patients with isoniazid- and streptomycin-resistance, 77.0% had clustered strains. DISCUSSION: In conclusion, although drug resistance among untreated Danes was close to the rate estimated in good national programmes, close monitoring is needed in future years, as active transmission...

Drug resistance in Mexico: results from the National Survey on Drug-Resistant Tuberculosis.

Science.gov (United States)

Bojorquez-Chapela, I; Bäcker, C E; Orejel, I; López, A; Díaz-Quiñonez, A; Hernández-Serrato, M I; Balandrano, S; Romero, M; Téllez-Rojo Solís, M M; Castellanos, M; Alpuche, C; Hernández-Ávila, M; López-Gatell, H

2013-04-01

To present estimations obtained from a population-level survey conducted in Mexico of prevalence rates of mono-, poly- and multidrug-resistant strains among newly diagnosed cases of pulmonary tuberculosis (TB), as well as the main factors associated with multidrug resistance (combined resistance to isoniazid and rifampicin). Study data came from the National Survey on TB Drug Resistance (ENTB-2008), a nationally representative survey conducted during 2008-2009 in nine states with a stratified cluster sampling design. Samples were obtained for all newly diagnosed cases of pulmonary TB in selected sites. Drug susceptibility testing (DST) was performed for anti-tuberculosis drugs. DST results were obtained for 75% of the cases. Of these, 82.2% (95%CI 79.5-84.7) were susceptible to all drugs. The prevalence of multidrug-resistant TB (MDR-TB) was estimated at 2.8% (95%CI 1.9-4.0). MDR-TB was associated with previous treatment (OR 3.3, 95%CI 1.1-9.4). The prevalence of drug resistance is relatively low in Mexico. ENTB-2008 can be used as a baseline for future follow-up of drug resistance.

Resistência de plantas daninhas aos herbicidas Weed resistance to herbicides

Directory of Open Access Journals (Sweden)

Pedro J. Christoffoleti

1994-01-01

Full Text Available A resistência de plantas daninhas aos herbicidas ocorre em função de um processo evolutivo. O desenvolvimento de biótipos de plantas daninhas resistentes é imposto pela agricultura moderna, através da pressão de seleção causada pelo uso intensivo dos herbicidas. O conhecimento dos mecanismos e fatores que favorecem o aparecimento de biótipos de plantas daninhas resistentes é fundamental para que técnicas de manejo sejam utilizadas no sentido de evitar ou retardar o aparecimento de plantas resistentes em uma área. São poucos os relatos ou citações de literatura no Brasil. Sendo assim, este trabalho de revisão procura relatar os principais avanços e descobertas na área de plantas daninhas resistentes aos herbicidas.Weed herbicide resistance has evolved from weed evolution. The modern agriculture is responsible for this evolution because of the intensive use of herbicides. The knowledge of mechanisms and factors that influence the weed herbicide resistance play an important role in the weed manegement techniques used to avoid or delay herbicide resistance appearence. There are not many report or scientific papers about herbi cide resistance in Brasil. Therefore, this literature review aims to provide information about the main advances and discoveries in the field of weed herbicide resistance.

Heat resistant/radiation resistant cable and incore structure test device for FBR type reactor

International Nuclear Information System (INIS)

Tanimoto, Hajime; Shiono, Takeo; Sato, Yoshimi; Ito, Kazumi; Sudo, Shigeaki; Saito, Shin-ichi; Mitsui, Hisayasu.

1995-01-01

A heat resistant/radiation resistant coaxial cable of the present invention comprises an insulation layer, an outer conductor and a protection cover in this order on an inner conductor, in which the insulation layer comprises thermoplastic polyimide. In the same manner, a heat resistant/radiation resistant power cable has an insulation layer comprising thermoplastic polyimide on a conductor, and is provided with a protection cover comprising braid of alamide fibers at the outer circumference of the insulation layer. An incore structure test device for an FBR type reactor comprises the heat resistant/radiation resistant coaxial cable and/or the power cable. The thermoplastic polyimide can be extrusion molded, and has excellent radiation resistant by the extrusion, as well as has high dielectric withstand voltage, good flexibility and electric characteristics at high temperature. The incore structure test device for the FBR type reactor of the present invention comprising such a cable has excellent reliability and durability. (T.M.)

Antimicrobial (Drug) Resistance

Science.gov (United States)

... with facebook share with twitter share with linkedin Antimicrobial (Drug) Resistance Go to Information for Researchers ► Credit: ... and infectious diseases. Why Is the Study of Antimicrobial (Drug) Resistance a Priority for NIAID? Over time, ...

Resistance seam welding

International Nuclear Information System (INIS)

Schueler, A.W.

1977-01-01

The advantages and disadvantages of the resistance seam welding process are presented. Types of seam welds, types of seam welding machines, seam welding power supplies, resistance seam welding parameters and seam welding characteristics of various metals

Predicting resistance by mutagenesis: lessons from 45 years of MBC resistance

Directory of Open Access Journals (Sweden)

Nichola J. Hawkins

2016-11-01

Full Text Available When a new fungicide class is introduced, it is useful to anticipate the resistance risk in advance, attempting to predict both risk level and potential mechanisms. One tool for the prediction of resistance risk is laboratory selection for resistance, with the mutational supply increased through UV or chemical mutagenesis. This enables resistance to emerge more rapidly than in the field, but may produce mutations that would not emerge under field conditions.The methyl-benzimidazole carbamates (MBCs were the first systemic single-site agricultural fungicides, and the first fungicides affected by rapid evolution of target-site resistance. MBC resistance has now been reported in over 90 plant pathogens in the field, and laboratory mutants have been studied in nearly 30 species.The most common field mutations, including β-tubulin E198A/K/G, F200Y and L240F, have all been identified in laboratory mutants. However, of 28 mutations identified in laboratory mutants, only nine have been reported in the field. Therefore, the predictive value of mutagenesis studies would be increased by understanding which mutations are likely to emerge in the field.Our review of the literature indicates that mutations with high resistance factors, and those found in multiple species, are more likely to be reported in the field. However, there are many exceptions, possibly due to fitness penalties. Whether a mutation occurred in the same species appears less relevant, perhaps because β-tubulin is highly conserved so functional constraints are similar across all species. Predictability of mutations in other target sites will depend on the level and conservation of constraints.

Changing prevalence and resistance patterns in children with drug-resistant tuberculosis in Mumbai.

Science.gov (United States)

Shah, Ira; Shah, Forum

2017-05-01

The prevalence of drug-resistant (DR) tuberculosis (TB) in children is increasing. Although, in India, multi-drug-resistant (MDR) TB rates have been relatively stable, the number of children with pre-extensively drug-resistant and extensively drug-resistant (XDR) TB is increasing. To determine whether the prevalence of DR TB in children in Mumbai is changing and to study the evolving patterns of resistance. A retrospective study was undertaken in 1311 paediatric patients referred between April 2007 and March 2013 to the Paediatric TB clinic at B. J. Wadia Hospital for Children, Mumbai. Children were defined as having DR TB on the basis of drug susceptibility testing (DST) of Mycobacterium tuberculosis grown on culture of body fluids (in the case of extra pulmonary TB) or from gastric lavage/bronchi-alveolar lavage/sputum in patients with pulmonary TB or from DST of the contacts. The prevalence of DR TB was calculated and the type of DR was evaluated yearly and in the pre-2010 and post-2010 eras. The overall prevalence of DR TB was 86 (6.6%) with an increase from 23 (5.6%) patients pre-2010 to 63 (7%) post-2010 (P = 0.40). Nine (10.4%) patients were diagnosed on the basis of contact with a parent with DR TB. Overall fluoroquinolone resistance increased from 9 (39.1%) pre-2010 to 59 (93.7%) post-2010 (P = 0.0001): moxifloxacin resistance increased from 2 (8.7%) to 29 (46%) (P = 0.0018) and ofloxacin resistance increased from 7 (30.4%) to 30 (47.6%) (P = 0.14). Ethionamide resistance also increased from 6 (26.1%) to 31 (49.2%) (P = 0.04), aminoglycoside resistance was one (4.3%) pre-2010 and 12 (19%) post-2010 (P = 0.17) and resistance remained virtually the same for both amikacin [0 pre-2010 and 6 (9.5%) after 2010] and kanamycin [one (4.3%) pre- and 6 (9.5%) post-2010]. Of the first-line drugs, resistance remained the same for isoniazid [23 (100%) to 61 (96.8%)], rifampicin [22 (95.7%) to 51 (80.9%),P = 0.17], pyrazinamide [15 (65.2%) to

Quantitative genetic tools for insecticide resistance risk assessment: estimating the heritability of resistance

Science.gov (United States)

Michael J. Firko; Jane Leslie Hayes

1990-01-01

Quantitative genetic studies of resistance can provide estimates of genetic parameters not available with other types of genetic analyses. Three methods are discussed for estimating the amount of additive genetic variation in resistance to individual insecticides and subsequent estimation of heritability (h2) of resistance. Sibling analysis and...

Resistance patterns among multidrug-resistant tuberculosis patients in greater metropolitan Mumbai: trends over time.

Science.gov (United States)

Dalal, Alpa; Pawaskar, Akshay; Das, Mrinalini; Desai, Ranjan; Prabhudesai, Pralhad; Chhajed, Prashant; Rajan, Sujeet; Reddy, Deepesh; Babu, Sajit; Jayalakshmi, T K; Saranchuk, Peter; Rodrigues, Camilla; Isaakidis, Petros

2015-01-01

While the high burden of multidrug-resistant tuberculosis (MDR-TB) itself is a matter of great concern, the emergence and rise of advanced forms of drug-resistance such as extensively drug-resistant TB (XDR-TB) and extremely drug-resistant TB (XXDR-TB) is more troubling. The aim of this study was to investigate the trends over time of patterns of drug resistance in a sample of MDR-TB patients in greater metropolitan Mumbai, India. This was a retrospective, observational study of drug susceptibility testing (DST) results among MDR-TB patients from eight health care facilities in greater Mumbai between 2005 and 2013. We classified resistance patterns into four categories: MDR-TB, pre-XDR-TB, XDR-TB and XXDR-TB. A total of 340 MDR-TB patients were included in the study. Pre-XDR-TB was the most common form of drug-resistant TB observed overall in this Mumbai population at 56.8% compared to 29.4% for MDR-TB. The proportion of patients with MDR-TB was 39.4% in the period 2005-2007 and 27.8% in 2011-2013, while the proportion of those with XDR-TB and XXDR-TB was changed from 6.1% and 0% respectively to 10.6% and 5.6% during the same time period. During the same periods, the proportions of patients with ofloxacin, moxifloxacin and ethionamide resistance significantly increased from 57.6% to 75.3%, from 60.0% to 69.5% and from 24.2% to 52.5% respectively (pMumbai highlight the need for individualized drug regimens, designed on the basis of DST results involving first- and second-line anti-TB drugs and treatment history of the patient. A drug-resistant TB case-finding strategy based on molecular techniques that identify only rifampicin resistance will lead to initiation of suboptimal treatment regimens for a significant number of patients, which may in turn contribute to amplification of resistance and transmission of strains with increasingly advanced resistance within the community.

Vancomycin Resistance in Staphylococcus aureus


Science.gov (United States)

McGuinness, Will A.; Malachowa, Natalia; DeLeo, Frank R.

2017-01-01

The evolution of Staphylococcus aureus during the modern antibiotic era has been delineated by distinct strain emergence events, many of which include acquisition of antibiotic resistance. The relative high burden of methicillin-resistant S. aureus (MRSA) in healthcare and community settings is a major concern worldwide. Vancomycin, a glycopeptide antibiotic that inhibits cell wall biosynthesis, remains a drug of choice for treatment of severe MRSA infections. S. aureus strains exhibiting increased resistance to vancomycin, known as vancomycin intermediate-resistant S. aureus (VISA) (MIC = 4-8 µg/mL), were discovered in the 1990s. The molecular basis of resistance in VISA is polygenic and involves stepwise mutations in genes encoding molecules predominantly involved in cell envelope biosynthesis. S. aureus isolates with complete resistance to vancomycin (MIC ≥ 16 µg/mL) are termed vancomycin-resistant S. aureus (VRSA)—they were first reported in the U.S. in 2002. Resistance in VRSA is conferred by the vanA gene and operon, which is present on a plasmid. Although treatment of VRSA infections is challenging, the total number of human VRSA infections to date is limited (14 in the U.S.). By comparison, the burden of VISA is relatively high and the molecular mechanisms of resistance are less well-defined. VISA are associated with persistent infections, vancomycin treatment failure, and poor clinical outcomes. Here, we review in brief progress made toward understanding the acquisition of antibiotic resistance in S. aureus, with an emphasis on the molecular mechanisms underlying vancomycin resistance. PMID:28656013

Reducing Resistance

DEFF Research Database (Denmark)

Lindell, Johanna

care may influence decisions on antibiotic use. Based on video-and audio recordings of physician-patient consultations it is investigated how treatment recommendations are presented, can be changed, are forecast and explained, and finally, how they seemingly meet resistance and how this resistance......Antibiotic resistance is a growing public health problem both nationally and internationally, and efficient strategies are needed to reduce unnecessary use. This dissertation presents four research studies, which examine how communication between general practitioners and patients in Danish primary...... is responded to.The first study in the dissertation suggests that treatment recommendations on antibiotics are often done in a way that encourages patient acceptance. In extension of this, the second study of the dissertation examines a case, where acceptance of such a recommendation is changed into a shared...

Multidrug Resistance in Infants and Children

Directory of Open Access Journals (Sweden)

Gian Maria Pacifici

2018-02-01

Full Text Available Bacterial infections may cause disease and death. Infants and children are often subject to bacterial infections. Antimicrobials kill bacteria protecting the infected patients andreducing the risk of morbidity and mortality caused by bacteria. The antibiotics may lose their antibacterial activity when they become resistant to a bacteria. The resistance to different antibiotics in a bacteria is named multidrug-resistance. Gram-negative bacilli, especially Escherichia coli, Klebsiella, Enterobacter, Salmonella, Shigella, Pseudomonas, Streptococcus, and Haemophilus influenzae type b, may become resistant. Amikacin ampicillin, amoxicillin, amoxiclav, cefuroxime, cefotaxime, ceftazidime, cefoperazone tetracycline, chloramphenicol, ciprofloxacin, and gentamicin may cause bacterial-resistance. Resistance to bacteria for several pathogens makes complications in the treatment of infections caused by them. Salmonella strains may become resistant to ampicillin, cephalotin, ceftriaxone, gentamicin, amikacin, trimethoprim-sulfamethoxazole, chloramphenicol, and tetracycline. Shigella strains may become resistant to ampicillin, cotrimoxazole, chloramphenicol, and streptomycin. Multidrug-resistance of Streptococcus pneumoniae may be due to β-lactams, macrolides, tetracycline, chloramphenicol, and trimethoprim-sulfamethoxazole. Multidrug-resistance of Pseudomonas aeruginosa may become resistant to β-lactams, chloramphenicol, trimethoprim-sulfamethoxazole, and tetracycline. The antibacterial activity against Haemophilus strains may occur with ampicillin, sulbactam-ampicillin, trimethoprim-sulfamethoxazole, gentamicin, chloramphenicol, and ciprofloxacin. Multidrug-resistance of the Klebsiella species may be due with ampicillin, cefotaxime, cefuroxime, co-amxilav, mezlocillin, chloramphenicol, gentamicin, and ceftazidime. Multidrug-resistance of Escherichia coli may be caused by ampicillin, cotrimoxazole, chloramphenicol, ceftriaxone, and ceftazidime. Vibrio

Triazole resistance surveillance in Aspergillus fumigatus.

Science.gov (United States)

Resendiz Sharpe, Agustin; Lagrou, Katrien; Meis, Jacques F; Chowdhary, Anuradha; Lockhart, Shawn R; Verweij, Paul E

2018-04-01

Triazole resistance is an increasing concern in the opportunistic mold Aspergillus fumigatus. Resistance can develop through exposure to azole compounds during azole therapy or in the environment. Resistance mutations are commonly found in the Cyp51A-gene, although other known and unknown resistance mechanisms may be present. Surveillance studies show triazole resistance in six continents, although the presence of resistance remains unknown in many countries. In most countries, resistance mutations associated with the environment dominate, but it remains unclear if these resistance traits predominately migrate or arise locally. Patients with triazole-resistant aspergillus disease may fail to antifungal therapy, but only a limited number of cohort studies have been performed that show conflicting results. Treatment failure might be due to diagnostic delay or due to the limited number of alternative treatment options. The ISHAM/ECMM Aspergillus Resistance Surveillance working group was set up to facilitate surveillance studies and stimulate international collaborations. Important aims are to determine the resistance epidemiology in countries where this information is currently lacking, to gain more insight in the clinical implications of triazole resistance through a registry and to unify nomenclature through consensus definitions.

Prevalence of plasmid-mediated quinolone resistance determinants among oxyiminocephalosporin-resistant Enterobacteriaceae in Argentina

Directory of Open Access Journals (Sweden)

Giovanna Rincon Cruz

2013-11-01

Full Text Available High quinolone resistance rates were observed among oxyiminocephalosporin-resistant enterobacteria. In the present study, we searched for the prevalence of plasmid-mediated quinolone resistance (PMQR genes within the 55 oxyiminocephalosporin-resistant enterobacteria collected in a previous survey. The main PMQR determinants were aac(6'-Ib-cr and qnrB, which had prevalence rates of 42.4% and 33.3%, respectively. The aac(6'-Ib-cr gene was more frequently found in CTX-M-15-producing isolates, while qnrB was homogeneously distributed among all CTX-M producers.

Whole genome analysis of linezolid resistance in Streptococcus pneumoniae reveals resistance and compensatory mutations

Directory of Open Access Journals (Sweden)

Légaré Danielle

2011-10-01

Full Text Available Abstract Background Several mutations were present in the genome of Streptococcus pneumoniae linezolid-resistant strains but the role of several of these mutations had not been experimentally tested. To analyze the role of these mutations, we reconstituted resistance by serial whole genome transformation of a novel resistant isolate into two strains with sensitive background. We sequenced the parent mutant and two independent transformants exhibiting similar minimum inhibitory concentration to linezolid. Results Comparative genomic analyses revealed that transformants acquired G2576T transversions in every gene copy of 23S rRNA and that the number of altered copies correlated with the level of linezolid resistance and cross-resistance to florfenicol and chloramphenicol. One of the transformants also acquired a mutation present in the parent mutant leading to the overexpression of an ABC transporter (spr1021. The acquisition of these mutations conferred a fitness cost however, which was further enhanced by the acquisition of a mutation in a RNA methyltransferase implicated in resistance. Interestingly, the fitness of the transformants could be restored in part by the acquisition of altered copies of the L3 and L16 ribosomal proteins and by mutations leading to the overexpression of the spr1887 ABC transporter that were present in the original linezolid-resistant mutant. Conclusions Our results demonstrate the usefulness of whole genome approaches at detecting major determinants of resistance as well as compensatory mutations that alleviate the fitness cost associated with resistance.

Report of workshop on vibration related to fluid in atomic energy field. 6

International Nuclear Information System (INIS)

1996-01-01

The accident of the fast breeder prototype reactor, 'Monju' on sodium leakage in its second cooling system occurred on December 8, 1995 was broadcast widely through mass-communication such as newspaper, television and others. Because of suspicion of whether concealment of videotape taken the accident state was intended to not, a method of information opening was an argument point. In spite of this, technical details of the accident was not transferred to researchers of each specified field by formal state still yet. Informations expected by the specialists of flow relating vibration are, for example, objective data such as accurate shape, eigenfrequency, attenuation, and others of the thermometer well, flow conditions and so forth, by knowing which they could judge reason of occurring the accident. It seems to be meaningful to conduct the information exchange on even a scale of the 'Yayoi Research Group'. Therefore, the Research Group was received all of objective facts on eddy excitation vibration of Monju's secondary system thermometer well accurately from its interested persons, reviewed on the eddy excitation vibration at this accident once more, and argued with a method of future research. In this book, the following 14 reports are described; 1) Outline of the Monju secondary system sodium leakage accident, 2) Karman vortex, 3) Flow at circumference of vibrates, 4) Flowing power analysis of the thermometer, 5) Flowing power vibration water flow test of the thermometer well, 6) Water flow test on the flow excitation vibration of the Monju's thermometer well, and others. (G.K.)

The perspectives of polygenic resistance in breeding for durable disease resistance

NARCIS (Netherlands)

Lindhout, P.

2002-01-01

Polygenic resistance is generally quantitative without clear race specific effects. With the onset of molecular markers technologies, the identification of chromosome regions that are involved in quantitative resistance has become feasible. These regions are designated quantitative trait loci

Resistência de Eleusine indica aos inibidores de ACCase Eleusine indica resistance to ACCase inhibitors

Directory of Open Access Journals (Sweden)

R.A. Vidal

2006-01-01

Full Text Available Dentre as causas da ineficácia no controle de plantas daninhas destaca-se a resistência delas aos herbicidas. Os objetivos deste trabalho foram avaliar a suspeita de resistência de Eleusine indica a inibidores de acetil-CoA carboxilase (ACCase e investigar a ocorrência de resistência cruzada entre os inibidores de ACCase. Biótipo de Eleusine indica originado do Mato Grosso com suspeita de resistência aos herbicidas inibidores de ACCase foi avaliado em casa de vegetação na sua suscetibilidade para diversos produtos do grupo dos ariloxifenoxipropionatos e cicloexanodionas. Estudos de resposta à dose confirmaram que o biótipo era 18 vezes mais insensível ao sethoxydim do que biótipo suscetível nunca aspergido com herbicidas. Também se constatou resistência cruzada ao fenoxaprop, cyhalofop, propaquizafop e butroxydim. Não se observou resistência cruzada aos produtos fluazifop, haloxyfop, quizalofop e clethodim.Among the causes for weed control inefficacy, the worst one is resistance to herbicides. The objectives of this work were to evaluate an Eleusine indica biotype suspected of resistance to ACCase inhibitors and to investigate the occurrence of cross- resistance to several ACCase inhibitors. One biotype of Eleusine indica originated from Mato Grosso with suspected resistance to ACCase inhibitors was evaluated in a greenhouse in relation to its susceptibility to several products of the ariloxyphenoxypropionate and cyclohexanedione groups. Studies on dose response confirmed that the suspected biotype was 18 times more insensitive to sethoxydim than the susceptible biotype that had never been treated with herbicides. Cross-resistance was confirmed for fenoxaprop, cyhalofop, propaquizafop and butroxydim. No cross-resistance was observed with fluazifop, haloxyfop, quizalofop, and clethodim.

Resistance to change

NARCIS (Netherlands)

Dow, J.; Perotti, E.

2009-01-01

Established firms often fail to maintain leadership following disruptive market shifts. We argue that such firms are more prone to internal resistance. A radical adjustment of assets affects the distribution of employee rents, creating winners and losers. Losers resist large changes when strong

A bacterial antibiotic-resistance gene that complements the human multidrug-resistance P-glycoprotein gene

NARCIS (Netherlands)

van Veen, HW; Callaghan, R; Soceneantu, L; Sardini, A; Konings, WN; Higgins, CF

1998-01-01

Bacteria have developed many fascinating antibiotic-resistance mechanisms(1,2). A protein in Lactococcus lactis, LmrA, mediates antibiotic resistance by extruding amphiphilic compounds from the inner leaflet of the cytoplasmic membrane(3,4). Unlike other known bacterial multidrug-resistance

FRC collisionless resistivity

International Nuclear Information System (INIS)

Tajima, T.; Horton, W.

1990-01-01

Ions in the field reversed configuration (FRC) exhibit stochastic orbits due to the field null and the curvature of poloidal field lines. Velocity correlations of these particles decay in a power law fashion t -m where 1 ≤ m ≤ 2. This decay of the single particle correlation function is characteristic of the long tail correlations of strongly chaotic or nonlinear systems found in other problems of statistical physics. This decay of correlations gives rise to a collisionless resistivity that can far exceed the collisional resistivity in an FRC plasma. The finite correlation τ c of a single particle limits the acceleration in the electric field producing the finite resistivity. Maxwellian test particle distributions are integrated to find the measure of the set of stochastic ions that contribute to the collisionless resistivity. The computed conductivity is proportional to the square root of the characteristic ion gyroradius in both simulation and theory

The Prehistory of Antibiotic Resistance.

Science.gov (United States)

Perry, Julie; Waglechner, Nicholas; Wright, Gerard

2016-06-01

Antibiotic resistance is a global problem that is reaching crisis levels. The global collection of resistance genes in clinical and environmental samples is the antibiotic "resistome," and is subject to the selective pressure of human activity. The origin of many modern resistance genes in pathogens is likely environmental bacteria, including antibiotic producing organisms that have existed for millennia. Recent work has uncovered resistance in ancient permafrost, isolated caves, and in human specimens preserved for hundreds of years. Together with bioinformatic analyses on modern-day sequences, these studies predict an ancient origin of resistance that long precedes the use of antibiotics in the clinic. Understanding the history of antibiotic resistance is important in predicting its future evolution. Copyright © 2016 Cold Spring Harbor Laboratory Press; all rights reserved.

Effect of Ampicillin, Streptomycin, Penicillin and Tetracycline on Metal Resistant and Non-Resistant Staphylococcus aureus

Directory of Open Access Journals (Sweden)

Dagmar Chudobova

2014-03-01

Full Text Available There is an arising and concerning issue in the field of bacterial resistance, which is confirmed by the number of deaths associated with drug-resistant bacterial infections. The aim of this study was to compare the effects of antibiotics on Staphylococcus aureus non-resistant strain and strains resistant to cadmium or lead ions. Metal resistant strains were created by the gradual addition of 2 mM solution of metal ions (cadmium or lead to the S. aureus culture. An increasing antimicrobial effect of ampicillin, streptomycin, penicillin and tetracycline (0, 10, 25, 50, 75, 150, 225 and 300 µM on the resistant strains was observed using a method of growth curves. A significant growth inhibition (compared to control of cadmium resistant cells was observed in the presence of all the four different antibiotics. On the other hand, the addition of streptomycin and ampicillin did not inhibit the growth of lead resistant strain. Other antibiotics were still toxic to the bacterial cells. Significant differences in the morphology of cell walls were indicated by changes in the cell shape. Our data show that the presence of metal ions in the urban environment may contribute to the development of bacterial strain resistance to other substances including antibiotics, which would have an impact on public health.

Effect of Ampicillin, Streptomycin, Penicillin and Tetracycline on Metal Resistant and Non-Resistant Staphylococcus aureus

Science.gov (United States)

Chudobova, Dagmar; Dostalova, Simona; Blazkova, Iva; Michalek, Petr; Ruttkay-Nedecky, Branislav; Sklenar, Matej; Nejdl, Lukas; Kudr, Jiri; Gumulec, Jaromir; Tmejova, Katerina; Konecna, Marie; Vaculovicova, Marketa; Hynek, David; Masarik, Michal; Kynicky, Jindrich; Kizek, Rene; Adam, Vojtech

2014-01-01

There is an arising and concerning issue in the field of bacterial resistance, which is confirmed by the number of deaths associated with drug-resistant bacterial infections. The aim of this study was to compare the effects of antibiotics on Staphylococcus aureus non-resistant strain and strains resistant to cadmium or lead ions. Metal resistant strains were created by the gradual addition of 2 mM solution of metal ions (cadmium or lead) to the S. aureus culture. An increasing antimicrobial effect of ampicillin, streptomycin, penicillin and tetracycline (0, 10, 25, 50, 75, 150, 225 and 300 µM) on the resistant strains was observed using a method of growth curves. A significant growth inhibition (compared to control) of cadmium resistant cells was observed in the presence of all the four different antibiotics. On the other hand, the addition of streptomycin and ampicillin did not inhibit the growth of lead resistant strain. Other antibiotics were still toxic to the bacterial cells. Significant differences in the morphology of cell walls were indicated by changes in the cell shape. Our data show that the presence of metal ions in the urban environment may contribute to the development of bacterial strain resistance to other substances including antibiotics, which would have an impact on public health. PMID:24651395

Herbicide resistance and biodiversity: agronomic and environmental aspects of genetically modified herbicide-resistant plants.

Science.gov (United States)

Schütte, Gesine; Eckerstorfer, Michael; Rastelli, Valentina; Reichenbecher, Wolfram; Restrepo-Vassalli, Sara; Ruohonen-Lehto, Marja; Saucy, Anne-Gabrielle Wuest; Mertens, Martha

2017-01-01

Farmland biodiversity is an important characteristic when assessing sustainability of agricultural practices and is of major international concern. Scientific data indicate that agricultural intensification and pesticide use are among the main drivers of biodiversity loss. The analysed data and experiences do not support statements that herbicide-resistant crops provide consistently better yields than conventional crops or reduce herbicide amounts. They rather show that the adoption of herbicide-resistant crops impacts agronomy, agricultural practice, and weed management and contributes to biodiversity loss in several ways: (i) many studies show that glyphosate-based herbicides, which were commonly regarded as less harmful, are toxic to a range of aquatic organisms and adversely affect the soil and intestinal microflora and plant disease resistance; the increased use of 2,4-D or dicamba, linked to new herbicide-resistant crops, causes special concerns. (ii) The adoption of herbicide-resistant crops has reduced crop rotation and favoured weed management that is solely based on the use of herbicides. (iii) Continuous herbicide resistance cropping and the intensive use of glyphosate over the last 20 years have led to the appearance of at least 34 glyphosate-resistant weed species worldwide. Although recommended for many years, farmers did not counter resistance development in weeds by integrated weed management, but continued to rely on herbicides as sole measure. Despite occurrence of widespread resistance in weeds to other herbicides, industry rather develops transgenic crops with additional herbicide resistance genes. (iv) Agricultural management based on broad-spectrum herbicides as in herbicide-resistant crops further decreases diversity and abundance of wild plants and impacts arthropod fauna and other farmland animals. Taken together, adverse impacts of herbicide-resistant crops on biodiversity, when widely adopted, should be expected and are indeed very hard

Resistance to fluoroquinolones and second-line injectable drugs: impact on multidrug-resistant TB outcomes

NARCIS (Netherlands)

Falzon, Dennis; Gandhi, Neel; Migliori, Giovanni B.; Sotgiu, Giovanni; Cox, Helen S.; Holtz, Timothy H.; Hollm-Delgado, Maria-Graciela; Keshavjee, Salmaan; Deriemer, Kathryn; Centis, Rosella; D'Ambrosio, Lia; Lange, Christoph G.; Bauer, Melissa; Menzies, Dick; Ahuja, S. D.; Ashkin, D.; Avendaño, M.; Banerjee, R.; Bauer, M.; Becerra, M. C.; Benedetti, A.; Burgos, M.; Centis, R.; Chan, E. D.; Chiang, C. Y.; Cobelens, F.; Cox, H.; D'Ambrosio, L.; de Lange, W. C. M.; DeRiemer, K.; Enarson, D.; Falzon, D.; Flanagan, K. L.; Flood, J.; Gandhi, N.; Garcia-Garcia, M. L.; Granich, R. M.; Hollm-Delgado, M. G.; Holtz, T. H.; Hopewell, P.; Iseman, M. D.; Jarlsberg, L. G.; Keshavjee, S.; Kim, H. R.; Koh, W. J.; Lancaster, J. L.; Lange, C.; Leimane, V.; Leung, C. C.; Li, J.

2013-01-01

A meta-analysis for response to treatment was undertaken using individual data of multidrug-resistant tuberculosis (MDR-TB) (resistance to isoniazid and rifampicin) patients from 26 centres. The analysis assessed the impact of additional resistance to fluoroquinolones and/or second-line injectable

Resistance to change

NARCIS (Netherlands)

Dow, J.; Perotti, E.

2013-01-01

Established firms often fail to maintain leadership following disrup tive market shifts. We argue that such firms are more prone to internal resistance. A radical adjustment of assets affects the distribution of employee rents, creating winners and losers. Losers resist large changes when strong

Antimicrobial resistance and resistance gene determinants in clinical Escherichia coli from different animal species in Switzerland.

Science.gov (United States)

Lanz, Roland; Kuhnert, Peter; Boerlin, Patrick

2003-01-02

Antimicrobial susceptibility testing was performed on a total of 581 clinical Escherichia coli isolates from diarrhea and edema disease in pigs, from acute mastitis in dairy cattle, from urinary tract infections in dogs and cats, and from septicemia in laying hens collected in Switzerland between 1999 and 2001. Among the 16 antimicrobial agents tested, resistance was most frequent for sulfonamides, tetracycline, and streptomycin. Isolates from swine presented significantly more resistance than those from the other animal species. The distribution of the resistance determinants for sulfonamides, tetracycline, and streptomycin was assessed by hybridization and PCR in resistant isolates. Significant differences in the distribution of resistance determinants for tetracycline (tetA, tetB) and sulfonamides (sulII) were observed between the isolates from swine and those from the other species. Resistance to sulfonamides could not be explained by known resistance mechanisms in more than a quarter of the sulfonamide-resistant and sulfonamide-intermediate isolates from swine, dogs and cats. This finding suggests that one or several new resistance mechanisms for sulfonamides may be widespread among E. coli isolates from these animal species. The integrase gene (intI) from class I integrons was detected in a large proportion of resistant isolates in association with the sulI and aadA genes, thus demonstrating the importance of integrons in the epidemiology of resistance in clinical E. coli isolates from animals.

Are Sewage Treatment Plants Promoting Antibiotic Resistance?

Science.gov (United States)

1. Introduction 1.1. How bacteria exhibit resistance 1.1.1. Resistance to -lactams 1.1.2. Resistance to sulphonamides and trimethoprim 1.1.3. Resistance to macrolides 1.1.4. Resistance to fluoroquinolones 1.1.5. Resistance to tetracyclines 1.1.6. Resistance to nitroimidaz...

Ceftaroline-Resistant, Daptomycin-Tolerant, and Heterogeneous Vancomycin-Intermediate Methicillin-Resistant Staphylococcus aureus Causing Infective Endocarditis.

Science.gov (United States)

Nigo, Masayuki; Diaz, Lorena; Carvajal, Lina P; Tran, Truc T; Rios, Rafael; Panesso, Diana; Garavito, Juan D; Miller, William R; Wanger, Audrey; Weinstock, George; Munita, Jose M; Arias, Cesar A; Chambers, Henry F

2017-03-01

We report a case of infective endocarditis (IE) caused by ceftaroline-resistant, daptomycin-tolerant, and heterogeneous vancomycin-intermediate methicillin-resistant S. aureus (MRSA). Resistance to ceftaroline emerged in the absence of drug exposure, and the E447K substitution in the active site of PBP2a previously associated with ceftaroline resistance was identified. Additionally, we present evidence of patient-to-patient transmission of the strain within the same unit. This case illustrates the difficulties in treating MRSA IE in the setting of a multidrug-resistant phenotype. Copyright © 2017 American Society for Microbiology.

A device for monitoring the coolant in a nuclear reactor tank

International Nuclear Information System (INIS)

Smith, R.D.

1984-01-01

The invention deals with a gamma thermometer where the gamma absorber (stainless steel) is in heat conducting connection with an external casing located in the coolant in a reactor tank. A heat sink for the gamma absorber heated by gamma irradiation from reactor fuel is thereby established. The most sensitive joint in the thermocouple of the gamma thermometer is mounted vertically above the other joint. A differential voltage with a certain polarity will be generated between the two joints during uniform cooling of the external casing. If the coolant falls to a level under the most sensitive joint, the resulting polarity change can be utilized for the activation of alarm systems. The same gamma thermometer may simultaneously be used as a sensor for measurement of local power distribution

Antimicrobial resistance and prevalence of resistance genes of obligate anaerobes isolated from periodontal abscesses.

Science.gov (United States)

Xie, Yi; Chen, Jiazhen; He, Junlin; Miao, Xinyu; Xu, Meng; Wu, Xingwen; Xu, Beiyun; Yu, Liying; Zhang, Wenhong

2014-02-01

This study attempts to determine the antimicrobial resistance profiles of obligate anaerobic bacteria that were isolated from a periodontal abscess and to evaluate the prevalence of resistance genes in these bacteria. Forty-one periodontal abscess samples were cultivated on selective and non-selective culture media to isolate the oral anaerobes. Their antibiotic susceptibilities to clindamycin, doxycycline, amoxicillin, imipenem, cefradine, cefixime, roxithromycin, and metronidazole were determined using the agar dilution method, and polymerase chain reaction assays were performed to detect the presence of the ermF, tetQ, nim, and cfxA drug resistance genes. A total of 60 different bacterial colonies was isolated and identified. All of the isolates were sensitive to imipenem. Of the strains, 6.7%, 13.3%, 16.7%, and 25% were resistant to doxycycline, metronidazole, cefixime, and amoxicillin, respectively. The resistance rate for both clindamycin and roxithromycin was 31.7%. Approximately 60.7% of the strains had the ermF gene, and 53.3% of the amoxicillin-resistant strains were found to have the cfxA gene. Two nim genes that were found in eight metronidazole-resistant strains were identified as nimB. In the present study, the Prevotella species are the most frequently isolated obligate anaerobes from periodontal abscesses. The current results show their alarmingly high resistance rate against clindamycin and roxithromycin; thus, the use of these antibiotics is unacceptable for the empirical therapy of periodontal abscesses. A brief prevalence of four resistance genes in the anaerobic bacteria that were isolated was also demonstrated.

Mapping resistance to powdery mildew in barley reveals a large-effect nonhost resistance QTL.

Science.gov (United States)

Romero, Cynara C T; Vermeulen, Jasper P; Vels, Anton; Himmelbach, Axel; Mascher, Martin; Niks, Rients E

2018-05-01

Resistance factors against non-adapted powdery mildews were mapped in barley. Some QTLs seem effective only to non-adapted mildews, while others also play a role in defense against the adapted form. The durability and effectiveness of nonhost resistance suggests promising practical applications for crop breeding, relying upon elucidation of key aspects of this type of resistance. We investigated which genetic factors determine the nonhost status of barley (Hordeum vulgare L.) to powdery mildews (Blumeria graminis). We set out to verify whether genes involved in nonhost resistance have a wide effectiveness spectrum, and whether nonhost resistance genes confer resistance to the barley adapted powdery mildew. Two barley lines, SusBgt SC and SusBgt DC , with some susceptibility to the wheat powdery mildew B. graminis f.sp. tritici (Bgt) were crossed with cv Vada to generate two mapping populations. Each population was assessed for level of infection against four B. graminis ff.spp, and QTL mapping analyses were performed. Our results demonstrate polygenic inheritance for nonhost resistance, with some QTLs effective only to non-adapted mildews, while others play a role against adapted and non-adapted forms. Histology analyses of nonhost interaction show that most penetration attempts are stopped in association with papillae, and also suggest independent layers of defence at haustorium establishment and conidiophore formation. Nonhost resistance of barley to powdery mildew relies mostly on non-hypersensitive mechanisms. A large-effect nonhost resistance QTL mapped to a 1.4 cM interval is suitable for map-based cloning.

Animation of Antimicrobial Resistance

Science.gov (United States)

... Animal & Veterinary Cosmetics Tobacco Products Animal & Veterinary Home Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin ...

Antibiotic resistance and resistance genes in Escherichia coli from poultry farms, southwest Nigeria.

Science.gov (United States)

Adelowo, Olawale O; Fagade, Obasola E; Agersø, Yvonne

2014-09-12

This study investigated the mechanisms of resistance in 36 E. coli isolated from waste, litter, soil and water samples collected from poultry farms in Southwestern Nigeria. Minimum inhibitory concentration (MIC) distributions of the isolates were determined using the methods of the Clinical and Laboratory Standard Institute and resistance genes detected by PCR. A total of 30 isolates (94%) showed resistance to more than one antimicrobial. Percentage resistance was: tetracycline 81%, sulphamethoxazole 67%, streptomycin 56%, trimethoprim 47 %, ciprofloxacin 42%, ampicillin 36%, spectinomycin 28%, nalidixic acid 25%, chloramphenicol 22%, neomycin 14%, gentamicin 8%, amoxicillin-clavulanate, ceftiofur, cefotaxime, colistin, florfenicol and apramycin 0%. Resistance genes found among the isolates include bla-TEM (85%), sul2 (67%), sul3 (17%), aadA (65%), strA (70%), strB (61%), catA1 (25%), cmlA1 (13%), tetA (21%) and tetB (17%). Class 1 and 2 integrons were found in five (14%) and six (17%) isolates, respectively, while one isolate was positive for both classes of integrons. Seven out of eight isolates with resistance to ciprofloxacin and MIC ≤ 32 mg/L to nalidixic acid contained qnrS genes. Our findings provided additional evidence that the poultry production environment in Nigeria represents an important reservoir of antibiotic resistance genes such as qnrS that may spread from livestock production farms to human populations via manure and water.

Observations on resistive wall modes

International Nuclear Information System (INIS)

Gerwin, R.A.; Finn, J.M.

1996-01-01

Several results on resistive wall modes and their application to tokamaks are presented. First, it is observed that in the presence of collisional parallel dynamics there is an exact cancellation to lowest order of the dissipative and sound wave effects for an ideal Ohm's law. This is easily traced to the fact that the parallel dynamics occurs along the perturbed magnetic field lines for such electromagnetic modes. Such a cancellation does not occur in the resistive layer of a tearing-like mode. The relevance to models for resistive wall modes using an electrostatic Hammett-Perkins type operator to model Landau damping will be discussed. Second, we observe that with an ideal Ohm's law, resistive wall modes can be destabilized by rotation in that part of parameter space in which the ideal MHD modes are stable with the wall at infinity. This effect can easily be explained by interpreting the resistive wall instability in terms of mode coupling between the backward stable MHD mode and a stable mode locked into the wall. Such an effect can occur for very small rotation for tearing-resistive wall modes in which inertia dominates viscosity in the layer, but the mode is stabilized by further rotation. For modes for which viscosity dominates in the layer, rotation is purely stabilizing. For both tearing models, a somewhat higher rotation frequency gives stability essentially whenever the tearing mode is stable with a perfectly conducting wall. These tearing/resistive wall results axe also simply explained in terms of mode coupling. It has been shown that resonant external ideal modes can be stabilized in the presence of resistive wall and resistive plasma with rotation of order the nominal tearing mode growth rate. We show that these modes behave as resistive wall tearing modes in the sense above. This strengthens the suggestion that rotational stabilization of the external kink with a resistive wall is due to the presence of resistive layers, even for ideal modes

Resist Parameter Extraction from Line-and-Space Patterns of Chemically Amplified Resist for Extreme Ultraviolet Lithography

Science.gov (United States)

Kozawa, Takahiro; Oizumi, Hiroaki; Itani, Toshiro; Tagawa, Seiichi

2010-11-01

The development of extreme ultraviolet (EUV) lithography has progressed owing to worldwide effort. As the development status of EUV lithography approaches the requirements for the high-volume production of semiconductor devices with a minimum line width of 22 nm, the extraction of resist parameters becomes increasingly important from the viewpoints of the accurate evaluation of resist materials for resist screening and the accurate process simulation for process and mask designs. In this study, we demonstrated that resist parameters (namely, quencher concentration, acid diffusion constant, proportionality constant of line edge roughness, and dissolution point) can be extracted from the scanning electron microscopy (SEM) images of patterned resists without the knowledge on the details of resist contents using two types of latest EUV resist.

Genetics Home Reference: clopidogrel resistance

Science.gov (United States)

... Facebook Twitter Home Health Conditions Clopidogrel resistance Clopidogrel resistance Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Clopidogrel resistance is a condition in which the drug clopidogrel ...

Genetics Home Reference: warfarin resistance

Science.gov (United States)

... Email Facebook Twitter Home Health Conditions Warfarin resistance Warfarin resistance Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Warfarin resistance is a condition in which individuals have ...

Resistance and conformity

NARCIS (Netherlands)

Sumter, S.R.; Bokhorst, C.L.; Westenberg, P.M.; Levesque, R.J.R.

2011-01-01

Resistance to peer influence, or the ability to resist making choices or adopting views under the implicit or explicit influence of your peers, is expected to undergo changes during adolescence. Two developmental trajectories have emerged from the field. On the one hand, adolescents show a temporary

[Molecular characterization of resistance mechanisms: methicillin resistance Staphylococcus aureus, extended spectrum β-lactamases and carbapenemases].

Science.gov (United States)

Oteo, Jesús; Belén Aracil, María

2015-07-01

Multi-drug resistance in bacterial pathogens increases morbidity and mortality in infected patients and it is a threat to public health concern by their high capacity to spread. For both reasons, the rapid detection of multi-drug resistant bacteria is critical. Standard microbiological procedures require 48-72 h to provide the antimicrobial susceptibility results, thus there is emerging interest in the development of rapid detection techniques. In recent years, the use of selective and differential culture-based methods has widely spread. However, the capacity for detecting antibiotic resistance genes and their low turnaround times has made molecular methods a reference for diagnosis of multidrug resistance. This review focusses on the molecular methods for detecting some mechanisms of antibiotic resistance with a high clinical and epidemiological impact: a) Enzymatic resistance to broad spectrum β-lactam antibiotics in Enterobacteriaceae, mainly extended spectrum β-lactamases (ESBL) and carbapenemases; and b) methicillin resistance in Staphylococcus aureus. Copyright © 2015 Elsevier España, S.L.U. All rights reserved.

Piggyback resistive Micromegas

CERN Document Server

Attié, D; Durand, D; Desforge, D; Ferrer-Ribas, E; Galán, J; Giomataris, Y; Gongadze, A; Iguaz, F J; Jeanneau, F; de Oliveira, R; Papaevangelou, T; Peyaud, A; Teixeira, A

2013-01-01

Piggyback Micromegas consists in a novel readout architecture where the anode element is made of a resistive layer on a ceramic substrate. The resistive layer is deposited on the thin ceramic substrate by an industrial process which provides large dynamic range of resistivity (10$^6$ to 10$^{10}$\\,M$\\Omega$/square). The particularity of this new structure is that the active part is entirely dissociated from the read-out element. This gives a large flexibility on the design of the anode structure and the readout scheme. Without significant loss, signals are transmitted by capacitive coupling to the read-out pads. The detector provides high gas gain, good energy resolution and the resistive layer assures spark protection for the electronics. This assembly could be combined with modern pixel array electronic ASICs. First tests with different Piggyback detectors and configurations will be presented. This structure is adequate for cost effective fabrication and low outgassing detectors. It was designed to perform ...

Effect of physiological age on radiation resistance of some bacteria that are highly radiation resistant

International Nuclear Information System (INIS)

Keller, L.C.; Maxcy, R.B.

1984-01-01

Physiological age-dependent variation in radiation resistance was studied for three bacteria that are highly radiation resistant: Micrococcus radiodurans, Micrococcus sp. isolate C-3, and Moraxella sp. isolate 4. Stationary-phase cultures of M. radiodurans and isolate C-3 were much more resistant to gamma radiation than were log-phase cultures. This pattern of relative resistance was reversed for isolate 4. Resistance of isolate 4 to UV light was also greater during log phase, although heat resistance and NaCl tolerance after heat stresses were greater during stationary phase. Radiation-induced injury of isolate 4 compared with injury of Escherichia coli B suggested that the injury process, as well as the lethal process, was affected by growth phase. The hypothesis that growth rate affects radiation resistance was tested, and results were interpreted in light of the probable confounding effect of methods used to alter growth rates of bacteria. These results indicate that dose-response experiments should be designed to measure survival during the most resistant growth phase of the organism under study. The timing is particularly important when extrapolations of survival results might be made to potential irradiation processes for foods. 17 references

An Investigation of the Relation Between Contact Thermometry and Dew-Point Temperature Realization

Science.gov (United States)

Benyon, R.; Böse, N.; Mitter, H.; Mutter, D.; Vicente, T.

2012-09-01

Precision optical dew-point hygrometers are the most commonly used transfer standards for the comparison of dew-point temperature realizations at National Metrology Institutes (NMIs) and for disseminating traceability to calibration laboratories. These instruments have been shown to be highly reproducible when properly used. In order to obtain the best performance, the resistance of the platinum resistance thermometer (PRT) embedded in the mirror is usually measured with an external, traceable resistance bridge or digital multimeter. The relation between the conventional calibration of miniature PRTs, prior to their assembly in the mirrors of state-of-the-art optical dew-point hygrometers and their subsequent calibration as dew-point temperature measurement devices, has been investigated. Standard humidity generators of three NMIs were used to calibrate hygrometers of different designs, covering the dew-point temperature range from -75 °C to + 95 °C. The results span more than a decade, during which time successive improvements and modifications were implemented by the manufacturer. The findings are presented and discussed in the context of enabling the optimum use of these transfer standards and as a basis for determining contributions to the uncertainty in their calibration.

Analysis of temperature changes on three-phase synchronous generator using infrared: comparison between balanced and unbalanced load

Science.gov (United States)

Amien, S.; Yoga, W.; Fahmi, F.

2018-02-01

Synchronous generators are a major tool in an electrical energy generating systems, the load supplied by the generator is unbalanced. This paper discusses the effect of synchronous generator temperature on the condition of balanced load and unbalanced load, which will then be compared with the measurement result of both states of the generator. Unbalanced loads can be caused by various asymmetric disturbances in the power system and the failure of load forecasting studies so that the load distribution in each phase is not the same and causing the excessive heat of the generator. The method used in data collection was by using an infrared thermometer and resistance calculation method. The temperature comparison result between the resistive, inductive and capacitive loads in the highest temperature balance occured when the generator is loaded with a resistive load, where T = 31.9 ° C and t = 65 minutes. While in a state of unbalanced load the highest temperature occured when the generator is loaded with a capacitive load, where T = 40.1 ° C and t = 60 minutes. By understanding this behavior, we can maintain the generator for longer operation life.

Multidrug resistance in tumour cells: characterisation of the multidrug resistant cell line K562-Lucena 1

Directory of Open Access Journals (Sweden)

VIVIAN M. RUMJANEK

2001-03-01

Full Text Available Multidrug resistance to chemotherapy is a major obstacle in the treatment of cancer patients. The best characterised mechanism responsible for multidrug resistance involves the expression of the MDR-1 gene product, P-glycoprotein. However, the resistance process is multifactorial. Studies of multidrug resistance mechanisms have relied on the analysis of cancer cell lines that have been selected and present cross-reactivity to a broad range of anticancer agents. This work characterises a multidrug resistant cell line, originally selected for resistance to the Vinca alkaloid vincristine and derived from the human erythroleukaemia cell K562. This cell line, named Lucena 1, overexpresses P-glycoprotein and have its resistance reversed by the chemosensitisers verapamil, trifluoperazine and cyclosporins A, D and G. Furthermore, we demonstrated that methylene blue was capable of partially reversing the resistance in this cell line. On the contrary, the use of 5-fluorouracil increased the resistance of Lucena 1. In addition to chemotherapics, Lucena 1 cells were resistant to ultraviolet A radiation and hydrogen peroxide and failed to mobilise intracellular calcium when thapsigargin was used. Changes in the cytoskeleton of this cell line were also observed.A resistência a múltiplos fármacos é o principal obstáculo no tratamento de pacientes com câncer. O mecanismo responsável pela resistência múltipla mais bem caracterizado envolve a expressão do produto do gene MDR-1, a glicoproteína P. Entretanto, o processo de resistência tem fatores múltiplos. Estudos de mecanismos de resistência m��ltipla a fármacos têm dependido da análise de linhagens celulares tumorais que foram selecionadas e apresentam reatividade cruzada a uma ampla faixa de agentes anti-tumorais. Este trabalho caracteriza uma linhagem celular com múltipla resistência a fármacos, selecionada originalmente pela resistência ao alcalóide de Vinca vincristina e derivado

Subgroup and resistance analyses of raltegravir for resistant HIV-1 infection

DEFF Research Database (Denmark)

Cooper, David A; Steigbigel, Roy T; Gatell, Jose M

2008-01-01

BACKGROUND: We evaluated the efficacy of raltegravir and the development of viral resistance in two identical trials involving patients who were infected with human immunodeficiency virus type 1 (HIV-1) with triple-class drug resistance and in whom antiretroviral therapy had failed. METHODS: We c...

Occurrence and Distribution of Antibiotic-resistant Bacteria and Transfer of Resistance Genes in Lake Taihu

Science.gov (United States)

Yin, Qian; Yue, Dongmei; Peng, Yuke; Liu, Ying; Xiao, Lin

2013-01-01

The overuse of antibiotics has accelerated antibiotic resistance in the natural environment, especially fresh water, generating a potential risk for public health around the world. In this study, antibiotic resistance in Lake Taihu was investigated and this was the first thorough data obtained through culture-dependent methods. High percentages of resistance to streptomycin and ampicillin among bacterial isolates were detected, followed by tetracycline and chloramphenicol. Especially high levels of ampicillin resistance in the western and northern regions were illustrated. Bacterial identification of the isolates selected for further study indicated the prevalence of some opportunistic pathogens and 62.0% of the 78 isolates exhibited multiple antibiotic resistance. The presence of ESBLs genes was in the following sequence: blaTEM > blaSHV > blaCTMX and 38.5% of the isolates had a class I integrase gene. Of all tested strains, 80.8% were able to transfer antibiotic resistance through conjugation. We also concluded that some new families of human-associated ESBLs and AmpC genes can be found in natural environmental isolates. The prevalence of antibiotic resistance and the dissemination of transferable antibiotic resistance in bacterial isolates (especially in opportunistic pathogens) was alarming and clearly indicated the urgency of realizing the health risks of antibiotic resistance to human and animal populations who are dependent on Lake Taihu for water consumption. PMID:24240317

Antibiotic Resistance and Antibiotic Resistance Genes in Escherichia coli Isolates from Hospital Wastewater in Vietnam.

Science.gov (United States)

Lien, La Thi Quynh; Lan, Pham Thi; Chuc, Nguyen Thi Kim; Hoa, Nguyen Quynh; Nhung, Pham Hong; Thoa, Nguyen Thi Minh; Diwan, Vishal; Tamhankar, Ashok J; Stålsby Lundborg, Cecilia

2017-06-29

The environmental spread of antibiotic-resistant bacteria has been recognised as a growing public health threat for which hospitals play a significant role. The aims of this study were to investigate the prevalence of antibiotic resistance and antibiotic resistance genes (ARGs) in Escherichia coli isolates from hospital wastewater in Vietnam. Wastewater samples before and after treatment were collected using continuous sampling every month over a year. Standard disk diffusion and E-test were used for antibiotic susceptibility testing. Extended-spectrum beta-lactamase (ESBL) production was tested using combined disk diffusion. ARGs were detected by polymerase chain reactions. Resistance to at least one antibiotic was detected in 83% of isolates; multidrug resistance was found in 32%. The highest resistance prevalence was found for co-trimoxazole (70%) and the lowest for imipenem (1%). Forty-three percent of isolates were ESBL-producing, with the bla TEM gene being more common than bla CTX-M . Co-harbouring of the bla CTX-M , bla TEM and qepA genes was found in 46% of isolates resistant to ciprofloxacin. The large presence of antibiotic-resistant E. coli isolates combined with ARGs in hospital wastewater, even post-treatment, poses a threat to public health. It highlights the need to develop effective processes for hospital wastewater treatment plants to eliminate antibiotic resistant bacteria and ARGs.

Dominance of multidrug resistant CC271 clones in macrolide-resistant streptococcus pneumoniae in Arizona

Directory of Open Access Journals (Sweden)

Bowers Jolene R

2012-01-01

Full Text Available Abstract Background Rates of resistance to macrolide antibiotics in Streptococcus pneumoniae are rising around the world due to the spread of mobile genetic elements harboring mef(E and erm(B genes and post-vaccine clonal expansion of strains that carry them. Results Characterization of 592 clinical isolates collected in Arizona over a 10 year period shows 23.6% are macrolide resistant. The largest portion of the macrolide-resistant population, 52%, is dual mef(E/erm(B-positive. All dual-positive isolates are multidrug-resistant clonal lineages of Taiwan19F-14, mostly multilocus sequence type 320, carrying the recently described transposon Tn2010. The remainder of the macrolide resistant S. pneumoniae collection includes 31% mef(E-positive, and 9% erm(B-positive strains. Conclusions The dual-positive, multidrug-resistant S. pneumoniae clones have likely expanded by switching to non-vaccine serotypes after the heptavalent pneumococcal conjugate vaccine release, and their success limits therapy options. This upsurge could have a considerable clinical impact in Arizona.

Evolution of methicillin-resistant Staphylococcus aureus towards increasing resistance

DEFF Research Database (Denmark)

Strommenger, Birgit; Bartels, Mette Damkjær; Kurt, Kevin

2014-01-01

To elucidate the evolutionary history of Staphylococcus aureus clonal complex (CC) 8, which encompasses several globally distributed epidemic lineages, including hospital-associated methicillin-resistant S. aureus (MRSA) and the highly prevalent community-associated MRSA clone USA300.......To elucidate the evolutionary history of Staphylococcus aureus clonal complex (CC) 8, which encompasses several globally distributed epidemic lineages, including hospital-associated methicillin-resistant S. aureus (MRSA) and the highly prevalent community-associated MRSA clone USA300....

Controlling antibiotic resistance in the ICU

NARCIS (Netherlands)

Derde, L.P.G.

2013-01-01

Patients admitted to intensive care units (ICUs) are frequently colonized with (antibiotic-resistant) bacteria, which may lead to healthcare associated infections. Antimicrobial-resistant bacteria (AMRB), such as methicillin-resistant Staphylococcus aureus (MRSA), vancomycin-resistant Enterococci

Clostridium difficile Infection and Patient-Specific Antimicrobial Resistance Testing Reveals a High Metronidazole Resistance Rate.

Science.gov (United States)

Barkin, Jodie A; Sussman, Daniel A; Fifadara, Nimita; Barkin, Jamie S

2017-04-01

Clostridium difficile (CD) infection (CDI) causes marked morbidity and mortality, accounting for large healthcare expenditures annually. Current CDI treatment guidelines focus on clinical markers of patient severity to determine the preferred antibiotic regimen of metronidazole versus vancomycin. The antimicrobial resistance patterns for patients with CD are currently unknown. The aim of this study was to define the antimicrobial resistance patterns for CD. This study included all patients with stools sent for CD testing to a private laboratory (DRG Laboratory, Alpharetta, Georgia) in a 6-month period from across the USA. Patient data was de-identified, with only age, gender, and zip-code available per laboratory protocol. All samples underwent PCR testing followed by hybridization for CD toxin regions A and B. Only patients with CD-positive PCR were analyzed. Antimicrobial resistance testing using stool genomic DNA evaluated presence of imidazole- and vancomycin-resistant genes using multiplex PCR gene detection. Of 2743, 288 (10.5%) stool samples were positive for CD. Six were excluded per protocol. Of 282, 193 (69.4%) were women, and average age was 49.4 ± 18.7 years. Of 282, 62 were PCR positive for toxins A and B, 160 for toxin A positive alone, and 60 for toxin B positive alone. Antimicrobial resistance testing revealed 134/282 (47.5%) patients resistant to imidazole, 17 (6.1%) resistant to vancomycin, and 9 (3.2%) resistant to imidazole and vancomycin. CD-positive patients with presence of imidazole-resistant genes from stool DNA extract was a common phenomenon, while vancomycin resistance was uncommon. Similar to treatment of other infections, antimicrobial resistance testing should play a role in CDI clinical decision-making algorithms to enable more expedited and cost-effective delivery of patient care.

Anticoagulant Resistance

DEFF Research Database (Denmark)

Heiberg, Ann-Charlotte

Although sewer rat control is carried out in more than 80 % of all Danish municipalities, with usage of large amounts of anticoagulant rodenticides, knowledge on anticoagulant resistance among rats living in the sewers is limited. As rat problems in urban areas are believed to be related to sewer...... problems (70-90 % in UK and DK) unawareness of resistance amongst these populations of Brown rats may constitute a future control problem and knowledge on this issue has become crucial. Rats were captured in sewers from seven different locations in the suburban area of Copenhagen. Locations was chosen...... to represent different sewer rat management strategies i) no anticoagulants for approx. 20 years ii) no anticoagulants for the last 5 years and iii) continuous control for many years. Animals were tested for resistance to bromadiolone by Blood-Clotting Response test, as bromadiolone is the most frequently used...

Embodied Resistance to Persuasion in Advertising

Science.gov (United States)

Lewinski, Peter; Fransen, Marieke L.; Tan, Ed S.

2016-01-01

From the literature on resistance to persuasion in advertising, much is known about how people can resist advertising by adopting resistance strategies, such as avoidance, counter-arguing, and selective attention (e.g., Fransen et al., 2015b). However, the role of emotion regulation and bodily expression in resisting persuasion is so far underexplored. This is a surprising observation if one considers that at least 40% of advertisements use positive emotions (i.e., happiness) to persuade people to like the ad, brand, and product (Weinberger et al., 1995). In this article we present a framework in which we apply previous knowledge and theories on emotion regulation and embodiment to the process of resistance to persuasion. In doing so, we specifically address the role of facial expression in the course of resistance. The literature and findings from our own research lead us to propose that people can resist persuasion by controlling their facial expression of emotion when exposed to an advertisement. Controlling the expression of emotions elicited by an ad (for example refusing to smile) might be a fruitful way to resist the ad’s persuasive potential. Moreover, we argue that co-viewers can affect embodied resistance to persuasion. Showing the viability of embodied resistance to persuasion is relevant in view of the fact that ads trying to persuade us by addressing our positive emotions are ubiquitous. Embodied resistance might help people to cope with these induced positive emotions in order to resist advertisements and might therefore work as a novel and effective strategy to resist persuasion. PMID:27574512

Embodied Resistance to Persuasion in Advertising

Directory of Open Access Journals (Sweden)

Peter Lewinski

2016-08-01

Full Text Available From the literature on resistance to persuasion in advertising, much is known about how people can resist advertising by adopting resistance strategies, such as avoidance, counter-arguing and selective attention (e.g., Fransen, Verlegh, Kirmani, & Smit, 2015a. However, the role of emotion regulation and bodily expression in resisting persuasion is so far underexplored. This is a surprising observation if one considers that at least 40% of advertisements use positive emotions (i.e., happiness to persuade people to like the ad, brand, and product (Weinberger et al., 1995. In this article we present a framework in which we apply previous knowledge and theories on emotion regulation and embodiment to the process of resistance to persuasion. In doing so, we specifically address the role of facial expression in the course of resistance. Based on the literature and findings largely established in our own research, we propose that people can resist persuasion by controlling their facial expression of emotion when exposed to an advertisement. Controlling the expression of emotions elicited by an ad (for example refusing to smile might be a fruitful way to resist the ad’s persuasive potential. Moreover, we argue that co-viewers can affect embodied resistance to persuasion. Showing the viability of embodied resistance to persuasion is relevant in view of the fact that ads trying to persuade us by addressing our positive emotions are ubiquitous. Embodied resistance might help people to cope with these induced positive emotions in order to resist advertisements and might therefore work as a novel and effective strategy to resist persuasion.

Embodied Resistance to Persuasion in Advertising.

Science.gov (United States)

Lewinski, Peter; Fransen, Marieke L; Tan, Ed S

2016-01-01

From the literature on resistance to persuasion in advertising, much is known about how people can resist advertising by adopting resistance strategies, such as avoidance, counter-arguing, and selective attention (e.g., Fransen et al., 2015b). However, the role of emotion regulation and bodily expression in resisting persuasion is so far underexplored. This is a surprising observation if one considers that at least 40% of advertisements use positive emotions (i.e., happiness) to persuade people to like the ad, brand, and product (Weinberger et al., 1995). In this article we present a framework in which we apply previous knowledge and theories on emotion regulation and embodiment to the process of resistance to persuasion. In doing so, we specifically address the role of facial expression in the course of resistance. The literature and findings from our own research lead us to propose that people can resist persuasion by controlling their facial expression of emotion when exposed to an advertisement. Controlling the expression of emotions elicited by an ad (for example refusing to smile) might be a fruitful way to resist the ad's persuasive potential. Moreover, we argue that co-viewers can affect embodied resistance to persuasion. Showing the viability of embodied resistance to persuasion is relevant in view of the fact that ads trying to persuade us by addressing our positive emotions are ubiquitous. Embodied resistance might help people to cope with these induced positive emotions in order to resist advertisements and might therefore work as a novel and effective strategy to resist persuasion.

Animation of Antimicrobial Resistance

Medline Plus

Full Text Available ... Animal & Veterinary Cosmetics Tobacco Products Animal & Veterinary Home Animal & Veterinary Safety & Health Antimicrobial Resistance Animation of Antimicrobial Resistance Share Tweet Linkedin Pin ...

Antimicrobial resistance, heavy metal resistance and integron content in bacteria isolated from a South African tilapia aquaculture system.

Science.gov (United States)

Chenia, Hafizah Y; Jacobs, Anelet

2017-11-21

Antibacterial compounds and metals co-select for antimicrobial resistance when bacteria harbour resistance genes towards both types of compounds, facilitating the proliferation and evolution of antimicrobial and heavy metal resistance. Antimicrobial and heavy metal resistance indices of 42 Gram-negative bacteria from a tilapia aquaculture system were determined to identify possible correlations between these phenotypes. Agar dilution assays were carried out to determine susceptibility to cadmium, copper, lead, mercury, chromate and zinc, while susceptibility to 21 antimicrobial agents was investigated by disk diffusion assays. Presence of merA, the mercury resistance gene, was determined by dot-blot hybridizations and PCR. Association of mercury resistance with integrons and transposon Tn21 was also investigated by PCR. Isolates displayed a high frequency of antimicrobial (erythromycin: 100%; ampicillin: 85%; trimethoprim: 78%) and heavy metal (Zn2+: 95%; Cd2+: 91%) resistance. No correlation was established between heavy metal and multiple antibiotic resistance indices. Significant positive correlations were observed between heavy metal resistance profiles, indices, Cu2+ and Cr3+ resistance with erythromycin resistance. Significant positive correlations were observed between merA (24%)/Tn21 (24%) presence and heavy metal resistance profiles and indices; however, significant negative correlations were obtained between integron-associated qacE∆1 (43%) and sulI (26%) gene presence and heavy metal resistance indices. Heavy metal and antimicrobial agents co-select for resistance, with fish-associated, resistant bacteria demonstrating simultaneous heavy metal resistance. Thus, care should be taken when using anti-fouling heavy metals as feed additives in aquaculture facilities.

Glyphosate resistance: state of knowledge

Science.gov (United States)

Sammons, Robert Douglas; Gaines, Todd A

2014-01-01

Studies of mechanisms of resistance to glyphosate have increased current understanding of herbicide resistance mechanisms. Thus far, single-codon non-synonymous mutations of EPSPS (5-enolypyruvylshikimate-3-phosphate synthase) have been rare and, relative to other herbicide mode of action target-site mutations, unconventionally weak in magnitude for resistance to glyphosate. However, it is possible that weeds will emerge with non-synonymous mutations of two codons of EPSPS to produce an enzyme endowing greater resistance to glyphosate. Today, target-gene duplication is a common glyphosate resistance mechanism and could become a fundamental process for developing any resistance trait. Based on competition and substrate selectivity studies in several species, rapid vacuole sequestration of glyphosate occurs via a transporter mechanism. Conversely, as the chloroplast requires transporters for uptake of important metabolites, transporters associated with the two plastid membranes may separately, or together, successfully block glyphosate delivery. A model based on finite glyphosate dose and limiting time required for chloroplast loading sets the stage for understanding how uniquely different mechanisms can contribute to overall glyphosate resistance. PMID:25180399

Emergence of fluoroquinolone resistance among drug resistant tuberculosis patients at a tertiary care facility in Karachi, Pakistan.

Science.gov (United States)

Zaidi, Syed Mohammad Asad; Haseeb, Abdul; Habib, Shifa Salman; Malik, Amyn; Khowaja, Saira; SaifUllah, Nausheen; Rizvi, Nadeem

2017-07-25

Pakistan is classified as one of the high multi-drug resistant tuberculosis (MDR-TB) burden countries. A poorly regulated private sector, over-prescription of antibiotics and self-medication has led to augmented rates of drug-resistance in the country. Pakistan's first national anti-tuberculosis drug resistance survey identified high prevalence of fluoroquinolone resistance among MDR-TB patients. Further institutional evidence of fluoroquinolone drug-resistance can support re-evaluation of treatment regimens as well as invigorate efforts to control antibiotic resistance in the country. In this study, data for drug-susceptibility testing (DST) was retrospectively analyzed for a total of 133 patients receiving MDR-TB treatment at the Chest Department of Jinnah Postgraduate Medical Center, Karachi, Pakistan. Frequency analyses for resistance patterns was carried out and association of fluoroquinolone (ofloxacin) resistance with demographics and past TB treatment category were assessed. Within first-line drugs, resistance to isoniazid was detected in 97.7% of cases, followed by rifampicin (96.9%), pyrazinamide (86.4%), ethambutol (69.2%) and streptomycin (64.6%). Within second-line drugs, ofloxacin resistance was detected in 34.6% of cases. Resistance to ethionamide and amikacin was 2.3% and 1.6%, respectively. Combined resistance of oflaxacin and isoniazid was detected in 33.9% of cases. Age, gender and past TB treatment category were not significantly associated with resistance to ofloxacin. Fluoroquinolone resistance was observed in an alarmingly high proportion of MDR-TB cases. Our results suggest caution in their use for empirical management of MDR-TB cases and recommended treatment regimens for MDR-TB may require re-evaluation. Greater engagement of private providers and stringent pharmacy regulations are urgently required.

Adriamycin resistance and radiation response

International Nuclear Information System (INIS)

Belli, J.A.; Harris, J.R.

1979-01-01

Mammalian cells (V79) in culture developed resistance to Adriamycin during continuous exposure to low levels of drug. This resistance was accompanied by change in x-ray survival properties which, in turn, depended upon the isolation of subpopulations from resistant sub lines. These changes in x-ray survival properties were characterized by reduced D/sub Q/ values and a decrease in the D/sub O/. However, these changes were not observed together in the same cell sub line. Adriamycin-resistant cells did not appear to be radiation damage repair deficient. Other phenotypic changes (cell morphology, DNA content and chromosome number) suggested mutational events coincident with the development of Adriamycin resistance

Measuring The Contact Resistances Of Photovoltaic Cells

Science.gov (United States)

Burger, D. R.

1985-01-01

Simple method devised to measure contact resistances of photovoltaic solar cells. Method uses readily available equipment and applicable at any time during life of cell. Enables evaluation of cell contact resistance, contact-end resistance, contact resistivity, sheet resistivity, and sheet resistivity under contact.

Animation of Antimicrobial Resistance

Medline Plus

Full Text Available ... More in Antimicrobial Resistance National Antimicrobial Resistance Monitoring System ... If you need help accessing information in different file formats, see Instructions for Downloading ...

Staphylococcus aureus: methicillin-susceptible S. aureus to methicillin-resistant S. aureus and vancomycin-resistant S. aureus.

Science.gov (United States)

Rehm, Susan J; Tice, Alan

2010-09-15

The evolution of methicillin-resistant and vancomycin-resistant Staphylococcus aureus has demanded serious review of antimicrobial use and development of new agents and revised approaches to prevent and overcome drug resistance. Depending on local conditions and patient risk factors, empirical therapy of suspected S. aureus infection may require coverage of drug-resistant organisms with newer agents and novel antibiotic combinations. The question of treatment with inappropriate antibiotics raises grave concerns with regard to methicillin-resistant S. aureus selection, overgrowth, and increased virulence. Several strategies to reduce the nosocomial burden of resistance are suggested, including shortened hospital stays and outpatient parenteral antimicrobial therapy of the most serious infections.

Time-Separating Heating and Sensor Functions of Thermistors in Precision Thermal Control Applications

Science.gov (United States)

Cho, Hyung J.; Sukhatme, Kalyani G.; Mahoney, John C.; Penanen, Konstantin Penanen; Vargas, Rudolph, Jr.

2010-01-01

A method allows combining the functions of a heater and a thermometer in a single device, a thermistor, with minimal temperature read errors. Because thermistors typically have a much smaller thermal mass than the objects they monitor, the thermal time to equilibrate the thermometer to the temperature of the object is typically much shorter than the thermal time of the object to change its temperature in response to an external perturbation.

Risk of vancomycin-resistant enterococci bloodstream infection among patients colonized with vancomycin-resistant enterococci

Directory of Open Access Journals (Sweden)

Ahu Kara

2015-01-01

Conclusion: In conclusion, our study found that 1.55% of vancomycin-resistant enterococci-colonized children had developed vancomycin-resistant enterococci bloodstream infection among the pediatric intensive care unit and hematology/oncology patients; according to our findings, we suggest that immunosupression is the key point for developing vancomycin-resistant enterococci bloodstream infections.

Relationship between Psidium species (Myrtaceae) by resistance gene analog markers: focus on nematode resistance.

Science.gov (United States)

Noia, L R; Tuler, A C; Ferreira, A; Ferreira, M F S

2017-03-16

Guava (Psidium guajava L.) crop is severely affected by the nematode Meloidogyne enterolobii. Native Psidium species have been reported as sources of resistance against this nematode. Knowledge on the molecular relationship between Psidium species based on plant resistance gene analogs (RGA) can be useful in the genetic breeding of guava for resistance to M. enterolobii. In this study, RGA markers from conserved domains, and structural features of plant R genes, were employed to characterize Psidium species and establish genetic proximity, with a focus on nematode resistance. SSR markers were also applied owing to their neutral nature, thus differing from RGA markers. For this, species reported as sources of resistance to M. enterolobii, such as P. cattleianum and P. friedrichsthalianum, as well as species occurring in the Atlantic Rainforest and susceptible genotypes, were investigated. In 10 evaluated Psidium species, high interspecific genetic variability was verified through RGA and SSR markers, with intraspecific variation in P. guajava higher with SSR, as was expected. Resistant species were clustered by RGA markers, and differential amplicons among genotypes resistant and susceptible to M. enterolobii were identified. Knowledge on the molecular relationships between Psidium species constitutes useful information for breeding of the guava tree, providing direction for hybridization and material for rootstocks. Additionally, the genetic relationship between native species, which have been little studied, and P. guajava were estimated by RGAs, which were confirmed as important markers for genetic diversity related to pathogen resistance.

The tetracycline resistance determinant Tet 39 and the sulphonamide resistance gene sulII are common among resistant Acinetobacter spp. isolated from integrated fish farms in Thailand

DEFF Research Database (Denmark)

Agersø, Yvonne; Petersen, Andreas

2007-01-01

Objectives: To determine the genetic basis for tetracycline and sulphonamide resistance and the prevalence of class I and II integrons in oxytetracycline-resistant Acinetobacter spp. from integrated fish farms in Thailand. Methods: A total of 222 isolates were screened for tetracycline resistance...... and Southern blots with sulII and tet(39) probes were performed on selected isolates. Results: The recently identified tetracycline resistance gene tet(39) was demonstrated in 75% (166/222) of oxytetracycline-resistant Acinetobacter spp. from integrated fish farms in Thailand. Isolates that were also...

Incidence of multidrug-resistant, extensively drug-resistant and pan-drug-resistant bacteria in children hospitalized at Dr. Hasan Sadikin general hospital Bandung Indonesia

Science.gov (United States)

Adrizain, R.; Suryaningrat, F.; Alam, A.; Setiabudi, D.

2018-03-01

Antibiotic resistance has become a global issue, with 700,000 deaths attributable to multidrug-resistance (MDR) occurring each year. Centers for Disease Control and Prevention (CDC) show rapidly increasing rates of infection due to antibiotic-resistant bacteria. The aim of the study isto describe the incidence of MDR, extensively drug-resistant (XDR) and pan drug-resistant (PDR) in Enterococcus spp., Staphylococcus aureus, K. pneumonia, Acinetobacter baumanii, P. aeruginosin, and Enterobacter spp. (ESKAPE) pathogens in children admitted to Dr. Hasan Sadikin Hospital. All pediatric patients having blood culture drawn from January 2015 to December 2016 were retrospectively studied. Data include the number of drawn blood culture, number of positive results, type of bacteria, sensitivity pattern. International standard definitions for acquired resistance by ECDC and CDC was used as definitions for MDR, XDR and PDR bacteria. From January 2015 to December 2016, 299 from 2.542 (11.7%) blood culture was positive, with Staphylococcus aureus, Enterococcus spp., Enterobacteriaceae, Pseudomonas aeruginosa, Acinetobacter spp., respectively 5, 6, 24, 5, 20 with total 60 (20%). The MDR and XDR pathogen found were 47 and 13 patients, respectively.

Multidrug-Resistant Salmonella enterica Serovar Muenchen from Pigs and Humans and Potential Interserovar Transfer of Antimicrobial Resistance

OpenAIRE

Gebreyes, Wondwossen A.; Thakur, Siddhartha

2005-01-01

Salmonella serovars are important reservoirs of antimicrobial resistance. Recently, we reported on multidrug-resistant (MDR) Salmonella enterica serovar Typhimurium strains among pigs with resistance to ampicillin, kanamycin, streptomycin, sulfamethoxazole, and tetracycline (resistance [R] type AKSSuT) and resistance to amoxicillin-clavulanic acid, ampicillin, chloramphenicol, streptomycin, sulfamethoxazole, and tetracycline (R type AxACSSuT). In the present study, 67 isolates (39 from humans...

Antimicrobial resistance

DEFF Research Database (Denmark)

Llor, Carl; Bjerrum, Lars

2014-01-01

Antimicrobial resistance is a global public health challenge, which has accelerated by the overuse of antibiotics worldwide. Increased antimicrobial resistance is the cause of severe infections, complications, longer hospital stays and increased mortality. Overprescribing of antibiotics......-the-counter sale of antibiotics, the use of antimicrobial stewardship programmes, the active participation of clinicians in audits, the utilization of valid rapid point-of-care tests, the promotion of delayed antibiotic prescribing strategies, the enhancement of communication skills with patients with the aid...

Phenotypic low-level isoniazid resistance as a marker to predict ethionamide resistance in Mycobacterium tuberculosis

Directory of Open Access Journals (Sweden)

Salima Qamar

2017-01-01

Full Text Available Background: Tuberculosis is one of the most prevalent diseases in Pakistan. Pakistan has the highest burden of MDR-TB in the Eastern Mediterranean region. Ethionamide is an anti-tuberculous drug frequently used to treat MDR-TB. Its drug susceptibility testing is not easily available in resource limited settings. Since it acts on the same target protein as isoniazid (inhA protein encoded by inhA gene, we sought to find out if phenotypic isoniazid resistance can be a marker of ethionamide resistance. Materials and Methods: This was a retrospective observational study conducted at the Aga Khan University hospital section of microbiology. Data was retrieved between 2011 to 2014 for all culture positive MTB strains. All culture positive MTB isolates with susceptibilities to isoniazid and ethionamide recorded were included in the study. Isoniazid and ethionamide susceptibilities were performed using agar proportion method on Middlebrook 7H10 agar. Rate of Ethionamide resistance between low-level isoniazid resistant, high level isoniazid resistant and isoniazid sensitive MTB was compared. Results: A total of 11,274 isolates were included in the study. A statistically significant association (P < 0.001 was found between Ethionamide resistance and low-level isoniazid resistance (26.6% as compared to high-level isoniazid resistance (8.85% and isoniazid sensitivity (0.71% in MTB strains. However this association was not seen in XDR-TB strains. Conclusion: Low level isoniazid resistance may be used as marker for phenotypic ethionamide resistance and hence guide clinicians' choice of antituberculous agent for MDR-TB in Pakistan. Further studies involving detection of genotypic association of isoniazid and ethionamide susceptibilities are needed before a final conclusion can be derived.

A double EPSPS gene mutation endowing glyphosate resistance shows a remarkably high resistance cost.

Science.gov (United States)

Han, Heping; Vila-Aiub, Martin M; Jalaludin, Adam; Yu, Qin; Powles, Stephen B

2017-12-01

A novel glyphosate resistance double point mutation (T102I/P106S, TIPS) in the 5-enolpyruvylshikimate-3-phosphate synthase (EPSPS) gene has been recently identified for the first time only in the weed species Eleusine indica. Quantification of plant resistance cost associated with the TIPS and the often reported glyphosate resistance single P106S mutation was performed. A significant resistance cost (50% in seed number currency) associated with the homozygous TIPS but not the homozygous P106S EPSPS variant was identified in E. indica plants. The resistance cost associated with the TIPS mutation escalated to 85% in plants under resource competition with rice crops. The resistance cost was not detected in nonhomozygous TIPS plants denoting the recessive nature of the cost associated with the TIPS allele. An excess of 11-fold more shikimate and sixfold more quinate in the shikimate pathway was detected in TIPS plants in the absence of glyphosate treatment compared to wild type, whereas no changes in these compounds were observed in P106S plants when compared to wild type. TIPS plants show altered metabolite levels in several other metabolic pathways that may account for the expression of the observed resistance cost. © 2017 John Wiley & Sons Ltd.

Insecticides resistance in the Culex quinquefasciatus populations from northern Thailand and possible resistance mechanisms.

Science.gov (United States)

Yanola, Jintana; Chamnanya, Saowanee; Lumjuan, Nongkran; Somboon, Pradya

2015-09-01

The mosquito vector Culex quinquefasciatus is known to be resistant to insecticides worldwide, including Thailand. This study was the first investigation of the insecticide resistance mechanisms, involving metabolic detoxification and target site insensitivity in C. quinquefasciatus from Thailand. Adult females reared from field-caught larvae from six provinces of northern Thailand were determined for resistant status by exposing to 0.05% deltamethrin, 0.75% permethrin and 5% malathion papers using the standard WHO susceptibility test. The overall mortality rates were 45.8%, 11.4% and 80.2%, respectively. A fragment of voltage-gated sodium channel gene was amplified and sequenced to identify the knock down resistance (kdr) mutation. The ace-1 gene mutation was determined by using PCR-RFLP. The L1014F kdr mutation was observed in all populations, but the homozygous mutant F/F1014 genotype was found only in two of the six provinces where the kdr mutation was significantly correlated with deltamethrin resistance. However, none of mosquitoes had the G119S mutation in the ace-1 gene. A laboratory deltamethrin resistant strain, Cq_CM_R, has been established showing a highly resistant level after selection for a few generations. The mutant F1014 allele frequency was significantly increased after one generation of selection. A synergist assay was performed to assess the metabolic detoxifying enzymes. Addition of bis(4-nitrophenyl)-phosphate (BNPP) and diethyl maleate (DEM), inhibitors of esterases and glutathione S-transferases (GST), respectively, into the larval bioassay of the Cq_CM strain with deltamethrin showed no significant reduction. By contrast, addition of piperonyl butoxide (PBO), an inhibitor of cytochrome P450 monooxygenases, showed a 9-fold reduction of resistance. Resistance to pyrethroids in C. quinquefasciatus is widely distributed in northern Thailand. This study reports for the first time for the detection of the L1014F kdr mutation in wild populations