WorldWideScience

Sample records for resin acid concentration

  1. Comparison of XAD macroporous resins for the concentration of fulvic acid from aqueous solution

    Science.gov (United States)

    Aiken, G.R.

    1979-01-01

    Five macroreticular, nonlonlc AmberlHe XAD resins were evaluated for concentration and Isolation of fulvlc acid from aqueous solution. The capacity of each resin for fulvlc acid was measured by both batch and column techniques. Elution efficiencies were determined by desorptlon with 0.1 N NaOH. Highest recoveries were obtained with the acrylic ester resins which proved to be most efficient for both adsorption and elution of fulvlc acid. Compared to the acrylic ester resins, usefulness of the styrene dvlnybenzene resins to remove fulvlc acid is limited because of slow diffusion-controlled adsorption and formation of charge-transfer complexes, which hinders elution. ?? 1979 American Chemical Society.

  2. Concentration and separation of trace metals with an arsonic acid resin.

    Science.gov (United States)

    Fritz, J S; Moyers, E M

    1976-08-01

    Macroporeus arsonic acid resins with different pore sizes and surface areas were prepared and the properties compared. One of the resins was used for concentration of trace metal ions from dimineralized water, tap-water, and sea-water. The effect of pH and complexing agents on the recovery of metal ions was studied. A method for separation of uranium(VI) and thorium(IV) from each other and from other metal ions was developed.

  3. Effects of different sulfuric acid etching concentrations on PEEK surface bonding to resin composite.

    Science.gov (United States)

    Chaijareenont, Pisaisit; Prakhamsai, Sasiprapha; Silthampitag, Patcharawan; Takahashi, Hidekazu; Arksornnukit, Mansuang

    2018-01-26

    This study evaluated the effects of surface pretreatment with different concentrations of sulfuric acid etching on surface properties and bonding between Polyetheretherketone (PEEK) and a resin composite. Six groups of surface pretreatment (no pretreatment, etched with 70, 80, 85, 90, and 98% sulfuric acid for 60 s) were treated on PEEK. Surface roughness, scanning electron microscopy (SEM) and atomic force microscopy (AFM) analyses were examined. Shear bond strength (SBS) and cross-sectional observations of the interfaces were performed. One-way ANOVA analysis revealed differences in surface roughness and SBS between groups. The 90 and 98% sulfuric acid etching significantly achieved the highest SBS (psulfuric acid etching were suggested to be the optimal concentration to improve adhesion between PEEK and the resin composite.

  4. Effect of Hydrofluoric Acid Concentration on Resin Adhesion to a Feldspathic Ceramic.

    Science.gov (United States)

    Venturini, Andressa Borin; Prochnow, Catina; Rambo, Dagma; Gundel, Andre; Valandro, Luiz Felipe

    2015-08-01

    To evaluate the effect of different concentrations of hydrofluoric acid (HF) on the contact angle and the resin bond strength durability to feldspathic ceramic. To evaluate the contact angles of distilled water on etched feldspathic ceramic, 25 specimens (12×10×2.4 mm) of VitaBlocks Mark II were used, divided into 5 groups (n=5): one unconditioned control (UC) group with no ceramic surface treatment, and 4 other groups that were etched for 60 s with different concentrations of HF: 1% (HF1), 3% (HF3), 5% (HF5) and 10% (HF10). The bond testing utilized 40 ceramic blocks (12×10×4 mm) that were fabricated and subjected to the same surface treatments as previously mentioned (excluding the control). The etched surfaces were silanized and resin cement was applied. After 24 h, the blocks were sectioned to produce bar specimens that were divided into two groups, non-aged (immediate testing) and aged (storage for 230 days+12,000 thermocycles at 5°C and 55°C), and subjected to microtensile testing (μTBS). Micromorphogical analysis of the treated surfaces was also performed (atomic force and scanning electron microscopy). One-way ANOVA and Tukey's tests were applied for data analysis. UC had the highest contact angle (61.4°), whereas HF10 showed the lowest contact angle (17.5°). In non-aged conditions, different acids promoted statistically similar bond strengths (14.2 to 15.7 MPa) (p>0.05); in terms of bond durability, only the bond strength of the HF1 group presented a statistically significant decrease comparing before and after aging (14.5 to 10.2 MPa). When etched with 3%, 5%, or 10% hydrofluoric acid, the ceramic tested showed stable resin adhesion after long-term aging.

  5. Raman spectroscopic study of the aging and nitration of actinide processing anion-exchange resins in concentrated nitric acid

    International Nuclear Information System (INIS)

    Buscher, C. T.; Donohoe, R. J.; Mecklenburg, S. L.; Berg, J. M.; Tait, C. D.; Huchton, K. M.; Morris, D. E.

    1999-01-01

    Degradation of two types of anion exchange resins, Dowex 11 and Reillex HPQ, from the action of concentrated nitric acid (4 to 12 M) and radiolysis [from depleted uranium as UO 2 2+ nitrate species and 239 Pu as Pu(IV) nitrate species] was followed as a function of time with Raman vibrational spectroscopy. Elevated temperatures (∼50 degree sign C) were used in the absence of actinide metal loading to simulate longer exposures of the resin to a HNO 3 process stream and waste storage conditions. In the absence of actinide loading, only minor changes in the Dowex resin at acid concentrations ≤10 M were observed, while at 12 M acid concentration, the emergence of a Raman peak at 1345 cm-1 indicates the addition of nitro functional groups to the resin. Similar studies with the Reillex resin show it to be more resistant to nitric acid attack at all acid concentrations. Incorporation of weakly radioactive depleted uranium as the UO 2 2+ nitrate species to the ion-exchange sites of Dowex 11 under differing nitric acid concentrations (6 to 12 M) at room temperature showed no Raman evidence of resin degradation or nitration, even after several hundred days of contact. In contrast, Raman spectra for Dowex 11 in the presence of 239 Pu as Pu(IV) nitrate species reveal numerous changes indicating resin alterations, including a new mode at 1345 cm-1 consistent with a Pu(IV)-nitrate catalyzed addition of nitro groups to the resin backbone. (c) 2000 Society for Applied Spectroscopy

  6. [Effect of hydrofluoric acid concentration on the surface morphology and bonding effectiveness of lithium disilicate glass ceramics to resin composites].

    Science.gov (United States)

    Hailan, Qian; Lingyan, Ren; Rongrong, Nie; Xiangfeng, Meng

    2017-12-01

    This study aimed at determining the influence of hydrofluoric acid (HF) in varied concentrations on the surface morphology of lithium disilicate glass ceramics and bond durability between resin composites and post-treated lithium disilicate glass ceramics. After being sintered, ground, and washed, 72 as-prepared specimens of lithium disilicate glass ceramics with dimensions of 11 mm×13 mm×2 mm were randomly divided into three groups. Each group was treated with acid solution [32% phosphoric acid (PA) or 4% or 9.5% HF] for 20 s. Then, four acidified specimens from each group were randomly selected. One of the specimens was used to observe the surface morphology using scanning electron microscopy, and the others were used to observe the surface roughness using a surface roughness meter (including Ra, Rz, and Rmax). After treatment with different acid solutions in each group, 20 samples were further treated with silane coupling agent/resin adhesive/resin cement (Monobond S/Multilink Primer A&B/Multilink N), followed by bonding to a composite resin column (Filtek™ Z350) with a diameter of 3 mm. A total of 20 specimens in each group were randomly divided into two subgroups, which were used for measuring the microshear bond strength, with one of them subjected to cool-thermal cycle for 20 000 times. The surface roughness (Ra, Rz, and Rmax) of lithium disilicate glass ceramics treated with 4% or 9.5% HF was significantly higher than that of the ceramic treated with PA (Pglass ceramics treated with 9.5% HF also demonstrated better surface roughness (Rz and Rmax) than that of the ceramics treated with 4% HF. Cool-thermal cycle treatment reduced the bond strength of lithium disilicate glass ceramics in all groups (Pglass ceramics treated with HF had higher bond strength than that of the ceramics treated with PA. The lithium disilicate glass ceramics treated with 4% HF had higher bond strength than that of the ceramics treated with 9.5% HF (Pglass ceramics treated with 4

  7. Diterpene resin acids in conifers.

    Science.gov (United States)

    Keeling, Christopher I; Bohlmann, Jörg

    2006-11-01

    Diterpene resin acids are a significant component of conifer oleoresin, which is a viscous mixture of terpenoids present constitutively or inducibly upon herbivore or pathogen attack and comprises one form of chemical resistance to such attacks. This review focuses on the recent discoveries in the chemistry, biosynthesis, molecular biology, regulation, and biology of these compounds in conifers.

  8. Boric acid concentration monitoring

    International Nuclear Information System (INIS)

    Kysela, J.; Mickal, V.; Racek, J.

    1978-01-01

    Boric acid concentration was measured by thermal neutron absorption in the study of the boric acid sorption and desorption curves on an anion exchange resin. Ra-Be 18.5 GBq and Am-Be 111 GBq sources and water as a moderator were used. The SNM 12 cylindrical corona detector with 10 B placed in the middle of the measuring cell was used for neutron flux measurement. The HP 9600 E computer system was used for measured data collection and evaluation. (Ha)

  9. Determination of isotopic composition of dissolved copper in seawater by multi-collector inductively coupled plasma mass spectrometry after pre-concentration using an ethylenediaminetriacetic acid chelating resin

    International Nuclear Information System (INIS)

    Takano, Shotaro; Tanimizu, Masaharu; Hirata, Takafumi; Sohrin, Yoshiki

    2013-01-01

    Graphical abstract: -- Highlights: •A simple analytical method for determining the Cu isotopic composition in seawater using an ethylenediaminetriacetic acid chelating resin was developed. •The accuracy was evaluated via addition of NIST SRM976 or 65 Cu-enriched standard to seawater. •δ 65 Cu of seawater reference materials (i.e., CASS-5 and NASS-6) and seawater samples from the northwestern Pacific Ocean were firstly determined. -- Abstract: Copper is an essential trace metal that shows a vertical recycled-scavenged profile in the ocean. To help elucidate the biogeochemical cycling of Cu in the present and past oceans, it is important to determine the distribution of Cu isotopes in seawater. However, precise isotopic analysis of Cu has been impaired by the low concentrations of Cu as well as co-existing elements that interfere with measurements by multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS). The objective of this study is to develop a simple Cu pre-concentration method using Nobias-chelate PA1 resin (Hitachi High Technologies). This extraction followed by anion exchange, allows precise analysis of the Cu isotopic composition in seawater. Using this method, Cu was quantitatively concentrated from seawater and >99.9999% of the alkali and alkaline earth metals were removed. The technique has a low procedural blank of 0.70 ng for Cu for a 2 L sample and the precision of the Cu isotopic analysis was ±0.07‰ (±2SD, n = 6). We applied this method to seawater reference materials (i.e., CASS-5 and NASS-6) and seawater samples obtained from the northwestern Pacific Ocean. The range of dissolved δ 65 Cu was 0.40–0.68‰

  10. Enhanced vanillin production from ferulic acid using adsorbent resin.

    Science.gov (United States)

    Hua, Dongliang; Ma, Cuiqing; Song, Lifu; Lin, Shan; Zhang, Zhaobin; Deng, Zixin; Xu, Ping

    2007-03-01

    High vanillin productivity was achieved in the batch biotransformation of ferulic acid by Streptomyces sp. strain V-1. Due to the toxicity of vanillin and the product inhibition, fed-batch biotransformation with high concentration of ferulic acid was unsuccessful. To solve this problem and improve the vanillin yield, a biotransformation strategy using adsorbent resin was investigated. Several macroporous adsorbent resins were chosen to adsorb vanillin in situ during the bioconversion. Resin DM11 was found to be the best, which adsorbed the most vanillin and the least ferulic acid. When 8% resin DM11 (wet w/v) was added to the biotransformation system, 45 g l(-1) ferulic acid could be added continually and 19.2 g l(-1) vanillin was obtained within 55 h, which was the highest vanillin yield by bioconversion until now. This yield was remarkable for exceeding the crystallization concentration of vanillin and therefore had far-reaching consequence in its downstream processing.

  11. Chelating ion exchange with macroreticular hydroxamic acid resins

    International Nuclear Information System (INIS)

    Phillips, R.J.

    1980-01-01

    The synthesis, reactions, and analytical applications of hydroxamic acids, including chelating resins with this functional group, are reviewed. A procedure for attaching N-phenyl hydroxamic acid groups to Amberlite XAD-4 is described. The extraction of 20 metal ions from 2M hydrochloric acid by this resin is discussed. Conditions for the quantitative extraction and back-extraction of 9 ions are reported. The results are compared with work on solvent extraction with N-phenylbenzohydroxamic acid. Procedures for attaching N-methyl and N-substituted hydroxamic acid groups to Amberlite XAD-4 are described. The N-phenyl, N-methyl, and N-unsubstituted hydroxamic acid resins are compared with respect to metal-ion complexation. The scope of applications for hydroxamic acid resins is investigated by studying the extraction of 19 metal ions as a function of pH. The resins are especially suitable for the extraction of zirconium(IV), titanium(IV), and uranium(IV) from strongly acidic solution. Aluminum(III) is separated from calcium and phosphate by extraction at pH 4. The use of the resins for the purification of reagents, concentration of trace constituents, and chromatographic separation is demonstrated

  12. Chelating ion exchange with macroreticular hydroxamic acid resins

    International Nuclear Information System (INIS)

    Phillips, R.J.

    1980-01-01

    The synthesis, reactions, and analytical applications of hydroxamic acids, including chelating resins with this functional group, are reviewed. A procedure for attaching N-phenyl hydroxamic acid groups to Amberlite XAD-4 is described. The extraction of 20 metal ions from 2 M hydrochloric acid by this resin is discussed. Conditions for the quantitative extraction and back-extraction of 9 ions are reported. Results are compared with work on solvent extraction with N-phenylbenzohydroxamic acid. Procedures for attaching N-methyl and N-unsubstituted hydroxamic acid groups to Amberlite XAD-4 are described. The N-phenyl, N-methyl, and N-unsubstituted hydroxamic acid resins are compared with respect to metal-ion complexation. The scope of applications for hydroxamic acid resins is investigated by studying the extraction of 19 metal ions as a function of pH. The resins are especially suitable for the extraction of zirconium(IV), titanium(IV), and uranium(IV) from strongly acidic solution. Aluminum(III) is separated from calcium and phosphate by extraction at pH 4. The use of the resins for the purification of reagents, concentration of trace constituents, and chromatographic separation is demonstrated

  13. Synthesis of novel chitosan resin derivatized with serine diacetic acid moiety and its application to on-line collection/concentration of trace elements and their determination using inductively coupled plasma-atomic emission spectrometry.

    Science.gov (United States)

    Hakim, Lukman; Sabarudin, Akhmad; Oshima, Mitsuko; Motomizu, Shoji

    2007-04-04

    A novel chelating resin functionalized with serine diacetic acid moiety was synthesized by using chitosan as base material, and applied to the collection/concentration of trace elements in environmental water samples, followed by the determination using inductively coupled plasma-atomic emission spectrometer (ICP-AES). The synthesized resin, crosslinked chitosan serine diacetic acid (CCTS-SDA), showed good adsorption behavior toward trace amounts of Cd, Pb, Cu, Ni, V, Ga, Sc, In, and Th in a wide pH range. Additionally, rare earth elements also can be retained on the resin at neutral pH region. The adsorbed elements can be easily eluted with 1 mol L(-1) of nitric acid, and their recoveries were found to be 90-100%. The CCTS-SDA was packed in a mini-column, which was then installed in a computer-controlled auto-pretreatment system (Auto-Pret System) for on-line trace elements collection and determination with ICP-AES. Experimental parameters which related to the improvement of sensitivity and reproducibility were optimized. The limits of detection (LOD) for 13 elements were found to be in sub-ppb level. The proposed method with CCTS-SDA resin was successfully applied to the determination of trace elements in river water samples. The method was validated by determining a certified reference material of river water, SLRS-4.

  14. Selective separation of indium by iminodiacetic acid chelating resin

    Energy Technology Data Exchange (ETDEWEB)

    Fortes, M.C.B.; Benedetto, J.S. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Martins, A.H. [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Engenharia Metalurgica e de Materiais]. E-mail: ahmartin@demet.ufmg.br

    2007-04-15

    - Indium can be recovered by treating residues, flue dusts, slags, and metallic intermediates in zinc smelting. This paper investigates the adsorption characteristics of indium and iron on an iminodiacetic acid chelating resin, Amberlite{sup R} IRC748 (Rohm and Haas Co.-USA). High concentrations of iron are always present in the aqueous feed solution of indium recovery. In addition, the chemical behaviour of iron in adsorptive systems is similar to that of indium. The metal concentrations in the aqueous solution were based on typical indium sulfate leach liquor obtained from zinc hydrometallurgical processing in a Brazilian plant. The ionic adsorption experiments were carried out by the continuous column method. Amberlite{sup R} IRC748 resin had a high affinity for indium under acidic conditions. Indium ions adsorbed onto the polymeric resin were eluted with a 0.5 mol/dm{sup 3} sulphuric acid solution passed through the resin bed in the column. 99.5% pure indium sulfate aqueous solution was obtained using the iminodiacetic acid chelating resin Amberlite{sup R} IRC748. (author)

  15. 21 CFR 573.120 - Acrylamide-acrylic acid resin.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Acrylamide-acrylic acid resin. 573.120 Section 573.120 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... Food Additive Listing § 573.120 Acrylamide-acrylic acid resin. Acrylamide-acrylic acid resin...

  16. Oxidation of resin acids in colophony (rosin) and its implications for patch testing.

    Science.gov (United States)

    Sadhra, S; Foulds, I S; Gray, C N

    1998-08-01

    Commercial preparations of colophony (rosin) used for patch testing are made from unmodified rosin in pet. and may be stored for some considerable time before being used. This would be satisfactory if the composition and dermatological activity of the preparations were both reproducible and stable, but investigations by the authors have shown that the resin acids undergo progressive and substantial oxidation and that the dermatological activity of the preparations increases significantly with time. This may be a cause of inconsistent patch test results unless the composition can be stabilized. Gas liquid chromatography (GLC) analysis of a raw rosin sample and its commercial patch test preparation has shown that they both contained the same resin acids, but the concentration of the abietic type resin acids was found to be lower in the patch test preparations. The degradation of resin acids is due to their atmospheric oxidation, which may occur during the preparation and storage of the commercial rosin patch test preparation. The susceptibility of individual resin acids to atmospheric oxidation was demonstrated by analysing a sample of raw Portuguese gum rosin, which was then left exposed to air and light. Most of the resin acids were found to undergo oxidation at a rate which gradually diminished. More importantly, it is presumed that the concentration of oxidized resin acids increased correspondingly, and these have been shown to be more dermatologically active than the unoxidised resin acids. The rate of decrease of resin acid concentration was found to be in the following order: neoabietic>levopimaric and palustric>abietic>dehydroabetic acid. The pimaric type resin acids were found to be relatively inert to atmospheric oxidation when compared with the abietic type resin acids. Patch testing with the resulting partly oxidized Portuguese rosin produced positive reactions at a 35% higher frequency than the raw Portuguese rosin. The study demonstrates that the

  17. The influence of plutonium concentration and solution flow rate on the effective capacity of macroporous anion exchange resin

    International Nuclear Information System (INIS)

    Marsh, S.F.; Gallegos, T.D.

    1987-07-01

    The principal aqueous process used to recover and purify plutonium at the Los Alamos Plutonium Facility is anion exchange in nitric acid. Previous studies with gel-type anion exchange resin have shown an inverse relationship between plutonium concentration in the feed solution and the optimum flow rate for this process. Because gel-type resin has been replaced with macroporous resin at Los Alamos, the relationship between plutonium concentration and solution flow rate was reexamined with the selected Lewatit MP-500-FK resin using solutions of plutonium in nitric acid and in nitric acid with high levels of added nitrate salts. Our results with this resin differ significantly from previous data obtained with gel-type resin. Flow-rate variation from 10 to 80 liters per hour had essentially no effect on the measured quantities of plutonium sorbed by the macroporous resin. However, the effect of plutonium concentration in the feed solutions was pronounced, as feed solutions that contained the highest concentrations of plutonium also produced the highest resin loadings. The most notable effect of high concentrations of dissolved nitrate salts in these solutions was an increased resin capacity for plutonium at low flow rates. 16 refs., 7 figs., 2 tabs

  18. Accurate determination of 129I concentrations and 129I/137Cs ratios in spent nuclear resins by Accelerator Mass Spectrometry

    International Nuclear Information System (INIS)

    Nottoli, Emmanuelle; Bienvenu, Philippe; Labet, Alexandre; Bourlès, Didier; Arnold, Maurice; Bertaux, Maité

    2014-01-01

    Determining long-lived radionuclide concentrations in radioactive waste has fundamental implications for the long-term management of storage sites. This paper focuses on the measurement of low 129 I contents in ion exchange resins used for primary fluid purification in Pressurised Water Reactors (PWR). Iodine-129 concentrations were successfully determined using Accelerator Mass Spectrometry (AMS) following a chemical procedure which included (1) acid digestion of resin samples in HNO 3 /HClO 4 , (2) radioactive decontamination by selective iodine extraction using a new chromatographic resin (CL Resin), and (3) AgI precipitation. Measured 129 I concentrations ranged from 4 to 12 ng/g, i.e. from 0.03 to 0.08 Bq/g. The calculation of 129 I/ 137 Cs activity ratios used for routine waste management produced values in agreement with the few available data for PWR resin samples. - Highlights: • In the context of radioactive waste management, this study aimed at measuring 129 I in spent resins using accelerator mass spectrometry. • The treatment procedure included microwave acid digestion of samples, iodine extraction by CL resins and AgI precipitation. • Developed first on synthetic matrices, the chemical treatment procedure was then successfully applied to real resin samples. • 129 I concentrations ranged from 4 to 12 ng/g of dry resin. • Results are in agreement with previous measurements and support reference values currently used for nuclear resin management

  19. The kinetics of fossil resin extraction from a flotation concentrate

    Energy Technology Data Exchange (ETDEWEB)

    Li, L.; Yu, Q.; Miller, J.D. [Univ. of Utah, Salt Lake City, UT (United States)

    1995-11-01

    The kinetics of fossil resin extraction from a flotation concentrate by heptane were investigated as a function of process variables using monosize particles. Experimental results provide for a better understanding of the refining process and the basis for subsequent design and construction of a continuous resin refining circuit. Based on the effect of process variables (particle size, stirring speed, and temperature) the resin extraction rate appears to be controlled by surface solvation phenomena. The initial extraction rate was found to be inversely proportional to the initial particle size and a kinetic model is being developed to describe the experimental results.

  20. Antimicrobial activity of resin acid derivatives.

    Science.gov (United States)

    Savluchinske-Feio, Sonia; Curto, Maria João Marcelo; Gigante, Bárbara; Roseiro, J Carlos

    2006-09-01

    The wide potential of resin acids as bioactive agents gave rise to a growing effort in the search for new applications of the natural forms and their derivatives. In some of these compounds, the antimicrobial activity is associated to the presence in the molecules of functional groups such as the hydroxyl, aldehyde, and ketone or to their cis or trans configurations. The resin acid family covers a spectrum of antimicrobial activities against several microorganisms, from bacteria to fungi, in which the mode of action was studied by electron microscopy. The morphological alterations are consistent with an unspecific mode of action causing inhibition of the fungal growth or damaging the fungal cells in parallel with a mechanism of resistance based on the retention of the compound by the lipid accumulation. The sterol composition of phytopathogenic fungi Botrytis cinerea and Lophodermium seditiosum treated with methyl cis-7-oxo-deisopropyldehydroabietate revealed the presence of ergosterol (M+ 396) and dihydroergosterol (M+ 398) in both cultures showing that this compound did not interfere with the ergosterol metabolic pathway of both fungi.

  1. Kinetic study of ion exchange in phosphoric acid chelating resin

    International Nuclear Information System (INIS)

    Brikci-Nigassa, Mounir; Hamouche, Hafida

    1995-11-01

    Uranium may be recovered as a by product of wet phosphoric acid using a method based on specific ion exchange resins. These resins called chelates contain amino-phosphonic functional groups. The resin studied in this work is a purolite S-940; uranium may be loaded on this resin from 30% P2O5 phosphoric acid in its reduced state. The influence of different parameters on the successive steps of the process have been studied in batch experiments: uranium reduction, loading and oxydation. Uranium may be eluted with ammonium carbonate and the resin regeneration may be done with hydrochloric acid.Ferric ions reduce the effective resin capacity considerably and inert fixation conditions are proposed to enhance uranium loading

  2. Study PWA8 resin for chromatographic uranium concentration

    International Nuclear Information System (INIS)

    Coceancigh, Herman; Ramella, J. L.; Marrero, Julieta; Jiménez Rebagliati, Raúl

    2013-01-01

    For many years nuclear industry have been using resins as filler of chromatographic columns. These methods are specific and give reliable results in different applications, for those reasons are extremely useful as separation process. Currently the nuclear industry is growing and this brings new issues such as the need of reduction of the amount of waste, the optimization of the production process and others that the chromatography could solve with great results. AMBERLITETM PWA8 resin is an anion exchange resin which can be used for the removal of uranium from drinking water. In addition to high exchange capacity, this resin has excellent physical stability and a wide range of pH in which is operational. With the idea of concentrating uranium from wastes solution as main goal we made different experiments to understand the AMBERLITETM PWA8 and obtain the most important characteristics like; pH working range; capacity; activation and elution procedures. These procedures were developed and optimized the capacity was determined using a batch experiment and we obtain that the maximum capacity is 882,5 U ug /resin gr at a pH of 4,2. Following on from these results chromatographic experiments were performed in which both were obtained the percentage of recovery and the concentration factor. The percent recovery (% R) calculated as the percentage ratio between the total mass and the load mass eluted (% R = eluted mass / total mass * 100) was 94% with a concentration factor of 5 times From these results it is intended to concentrate wastes solutions from the fuel cycle processes with two main goals: decreasing volume for storage and for future reusing of the uranium coming from production. (author)

  3. Accurate determination of 41Ca concentrations in spent resins from the nuclear industry by Accelerator Mass Spectrometry

    International Nuclear Information System (INIS)

    Nottoli, Emmanuelle; Bourlès, Didier; Bienvenu, Philippe; Labet, Alexandre; Arnold, Maurice; Bertaux, Maité

    2013-01-01

    The radiological characterisation of nuclear waste is essential for managing storage sites. Determining the concentration of Long‐Lived RadioNuclides (LLRN) is fundamental for their long-term management. This paper focuses on the measurement of low 41 Ca concentrations in ions exchange resins used for primary fluid purification in Pressurised Water Reactors (PWR). 41 Ca concentrations were successfully measured by Accelerator Mass Spectrometry (AMS) after the acid digestion of resin samples, followed by radioactive decontamination and isobaric suppression through successive hydroxide, carbonate, nitrate and final CaF 2 precipitations. Measured 41 Ca concentrations ranged from 0.02 to 0.03 ng/g, i.e. from 0.06 to 0.09 Bq/g. The 41 Ca/ 60 Co activity ratios obtained were remarkably reproducible and in good agreement with the current ratio used for resins management. - Highlights: • In the context of radioactive waste management, this study aimed at measuring 41 Ca in spent resins using Accelerator Mass Spectrometry. • A chemical treatment procedure was developed to quantitatively recover calcium in solution and selectively extract it. • Developed firstly on synthetic matrices, the chemical treatment procedure was then successfully applied to real resin samples. • Accelerator mass spectrometry allowed measuring concentrations of 41 Ca in spent resins as low as 0.02 ng/g of dry resin. • Final results are in agreement with current data used for spent resins management

  4. In vitro adsorption of oxalic acid and glyoxylic acid onto activated charcoal, resins and hydrous zirconium oxide

    NARCIS (Netherlands)

    Scholtens, R.; Scholten, J.; de Koning, H. W.; Tijssen, J.; ten Hoopen, H. W.; Olthuis, F. M.; Feijen, J.

    1982-01-01

    Patients suffering from primary hyperoxaluria show elevated plasma concentrations of oxalic acid and glyoxylic acid. The in vitro adsorption of these compounds into activated charcoal, a series of neutral and ion exchange resins and onto hydrous zirconium oxide has been investigated. Hydrous

  5. Synthesis and characterization of an N-(2-hydroxyethyl)-ethylenediaminetriacetic acid resin

    International Nuclear Information System (INIS)

    Lai, Y.F.

    1977-10-01

    A chelating ion-exchange resin with N-(2-hydroxyethyl)ethylene-diaminetriacetic acid (HEDTA) used as the ligand chemically bonded to XAD-4 by an ester linkage, HEDTA-4, was synthesized. It is stable under normal experimental conditions with the liquid chromatograph. The structure of the resin was confirmed by an infrared spectrum, and by potentiometric titrations. The capacity of the resin was also obtained by potentiometric titration and by a nitrogen analysis. The resin was used to pack a column of 5 mm internal diameter and 5 cm long. The effect of pH on the retention of different metal ions on the resin was studied. It was found that the resin was most selective for chromium(III), copper(II), lead(II), mercury(II), uranium(VI), zirconium(IV) and zinc(II) at a pH of less than 3. Furthermore, the resin proves to be functioning with a chelating mechanism rather than ion-exchange, and it can concentrate trace metal ions in the presence of a large excess of calcium and magnesium. This makes the resin potentially useful for purifying and analyzing drinking water

  6. Uranium extraction from sulfuric acid solution using anion exchange resin

    International Nuclear Information System (INIS)

    Sheta, M. E.; Abdel Aal, M. M.; Kandil, A. T.

    2012-12-01

    Uranium is currently recovered from sulfuric acid leach liquor using anion exchange resin as Amberlite IRA 402 (CT). This technology is based on fact that, uranium exists as anionic complexes. This takes place by controlling the pH of the solution, agitation time, temperature and resin to solution ratio (R/S). In this work, batch stirrer tank used for uranium extraction from sulfate medium and after extraction, elution process was done using 1M NaCl solution. After extraction and elution process, the resin was separated from the system and uranium was determined in the solution. (Author)

  7. The use of extraction chromatography resins to concentrate actinides and strontium from soil for radiochromatographic analyses.

    Science.gov (United States)

    Roane, J E; DeVol, T A; Leyba, J D; Fjeld, R A

    2003-01-01

    An analytical technique utilizing selective extractant resins to concentrate strontium and actinides from soil followed by separation with radiochromatography was evaluated. The technique was tested using uncontaminated soil samples spiked with a radionuclide tracer solution that were either microwave-aided acid digested or leached with a strong acid. Extraction of the strontium and actinides from the acidified solution was accomplished using a serial arrangement of Sr-Resin and TRU-Resin columns. The combined eluate solutions from the extraction resins were treated with HNO(3) and H(2)O(2) to oxidize residual extractant and eluates prior to separation and analysis of the radionuclides by radiochromatography. Chromatograms obtained with larger soil mass loadings resulted in either incomplete peak resolution of the tracers or had highly variable peak elution times, indicative of an ionic interfering constituent(s). Better separations (e.g., chromatograms that resolved all radioactive constituents) were obtained when the sample mass loading was decreased, but with a concurrent decreased sensitivity for the radionuclides. Elemental analyses of the soil were conducted to provide data on the ionic constituents in unprocessed soil and post-processed soil samples. These results identified aluminum as an interfering contributor to the poor performance exhibited by the radiochromatographic separations.

  8. A novel malonamide grafted polystyrene-divinyl benzene resin for extraction, pre-concentration and separation of actinides.

    Science.gov (United States)

    Ansari, S A; Mohapatra, P K; Manchanda, V K

    2009-01-30

    A new chelating polymeric extraction chromatographic resin was prepared by chemical anchoring of N,N'-dimethyl-N,N'-dibutyl malonamide (DMDBMA) with chloromethylated Merrifield resin((R)). The grafted resin exhibited stronger binding for hexavalent and tetravalent actinides such as U(VI), Th(IV) and Pu(IV) over trivalent actinides, viz. Am(III) and Pu(III). Batch studies on solid phase extraction performed over a wide range of acid solution (0.01-6M HNO(3)) revealed that ternary mixer of uranium, americium and plutonium or thorium, americium and plutonium could be separated from each other at 1M HNO(3). Desorption of U(VI), Pu(IV) and Am(III) from the loaded resin was efficiently carried out using 0.1M alpha-HIBA, 0.25M oxalic acid and 0.01M EDTA, respectively. Quantitative pre-concentration of actinide ions such as Th(IV) and U(VI) was possible from 3M HNO(3) solution. The practical utility of the grafted resin was evaluated by uranium sorption measurements in several successive cycles. The sorption efficiency of the resin with respect to uranyl ion remained unchanged even after 30 days of continuous use. The surface morphology of the resin was monitored with the help of scanning electron microscopy (SEM) technique.

  9. Green biorefinery: separation of lactic acid from grass silage juice by chromatography using neutral polymeric resin.

    Science.gov (United States)

    Thang, Vu Hong; Novalin, Senad

    2008-07-01

    The aim of this work was to recover lactic acid in undissociated form from grass silage juice. For this aim, chromatographic separation using neutral polymeric resin Amberlite XAD1600 was investigated. Up to now, there is no hint in the literatures about using neutral polymeric resin for lactic acid separation from a mixture. Important factors (flow-rate, concentration of feed and loaded volume) that affect separation performance were firstly investigated with model solutions. The obtained results showed that lactic acid solutions with the purity varying from 93.2% to 99.9% could be obtained at the recovery yields over 99.4%. After that, trials with silage juice were carried out. Due to the complex composition of the feed, the purity of products decreased to 94% at a recovery yield of 97%. Although 99% of inorganic salts and sugars were separated from lactic acid organic acids in general and acetic acid in particular caused a purity problem. It seems that organic acids could not be separated from lactic acid by neutral resin Amberlite XAD1600. Besides the organic acid problem, some amino acids were remained in the products as impurities.

  10. Input to Resin Column Structural Analysis if Autocatalytic Resin Reaction Occurs in HB-Line Phase II

    Energy Technology Data Exchange (ETDEWEB)

    Hallman, D.F.

    2001-07-10

    Solutions of plutonium in nitric acid are purified and concentrated using anion resin prior to precipitation. There have been instances of resin column explosions caused by autocatalytic reactions of anion resins in nitric acid within the DOE complex

  11. Design and synthesis of bio-based UV curable PU acrylate resin from itaconic acid for coating applications.

    Science.gov (United States)

    Patil, Deepak M; Phalak, Ganesh A; Mhaske, S T

    2017-01-01

    UV curable PUA resin was successfully synthesized from polyol based on sustainable resource originated from itaconic acid (IA), isophorone diisocyanate (IPDI) and 2-hydroxyethyl methacrylate (HEMA). A polyol was synthesized by condensation reaction of IA with 16-hexanediol in the presence of p-Toluenesulfonic acid (pTSA). The synthesized PUA resin was characterized for its structural elucidation by using Fourier Transform Infrared Spectrophotometer (FTIR), 1 H and 13 C NMR spectroscopy. The synthesized UV curable PUA resin was incorporated in varying concentrations in conventional PUA coating system. The effects of varying concentration of synthesized UV curable PUA resin on rheology, crystallinity, thermal and coating properties were evaluated. The rheological behavior of the resins were evaluated at variable stress and result showed decrease in viscosity of resin as concentration of synthesized UV curable PUA resin increases in conventional PUA resin. The cured coatings have been evaluated for glass transition temperature ( T g ) and thermal behavior by differential scanning calorimeter and thermogravimetric analysis respectively. The degree of crystallinity of the coatings was determined from X-ray diffraction patterns using the PFM program. It was found that increase in the mass proportion of IA based PUA in coatings, the coating becomes more rigid and crystalline. The synthesized UV curable PUA coatings showed interesting mechanical, chemical, solvent and thermal properties as compared to the conventional PUA. Further, cured coatings were also evaluated for gel content and water absorption.

  12. [Absorption and isolation of macroporous resin for five salvianolic acids from Salviae mitiorrhizae].

    Science.gov (United States)

    Wang, Yan-Yan; Zhu, Jing-Bo; Li, Lin; Jin, Yue

    2008-05-01

    To study the adsorption of the macroporous resin for the five salvianolic acids (danshen su, rosmarinic acid, protocate chualdehyde, salvianolic acid B, salvianolic acid A, extracted from Salviae mitiorrhizae. The five salvianolic acids were employed as an index, and the change of them in the static and dynamic absorbent was detected by HPLC, respectively. HP20 resin was a suitable marcoporous resin to purify salvianolic acids. The dynamic adsorption capacity of rosmarinic acid, salvianolic acid B and salvianolic acid A was 30.506 mg x g(-1) (dry resin), 36.996 mg x g(-1), (dry resin), 43.85 mg x g(-1) (dry resin) respectively. It is not suitable that danshensu and protocate chualdehyde are the evaluation indexes for using 8 macroporous resins to purify salvianolic acids.

  13. Exposure to wood dust, resin acids, and volatile organic compounds during production of wood pellets.

    Science.gov (United States)

    Hagström, Katja; Axelsson, Sara; Arvidsson, Helena; Bryngelsson, Ing-Liss; Lundholm, Cecilia; Eriksson, Kåre

    2008-05-01

    The main aim of this study was to investigate exposure to airborne substances that are potentially harmful to health during the production of wood pellets, including wood dust, monoterpenes, and resin acids, and as an indicator of diesel exhaust nitrogen dioxide. In addition, area measurements were taken to assess background exposure levels of these substances, volatile organic compounds (VOCs), and carbon monoxide. Measurements were taken at four wood pellet production plants from May 2004 to April 2005. Forty-four workers participated in the study, and a total of 68 personal measurements were taken to determine personal exposure to wood dust (inhalable and total dust), resin acids, monoterpenes, and nitrogen dioxide. In addition, 42 measurements of nitrogen dioxide and 71 measurements of total dust, resin acids, monoterpenes, VOCs, and carbon monoxide were taken to quantify their indoor area concentrations. Personal exposure levels to wood dust were high, and a third of the measured levels of inhalable dust exceeded the Swedish occupational exposure limit (OEL) of 2 mg/m3. Parallel measurements of inhalable and total dust indicated that the former were, on average, 3.2 times higher than the latter. The data indicate that workers at the plants are exposed to significant amounts of the resin acid 7-oxodehydroabietic acid in the air, an observation that has not been recorded previously at wood processing and handling plants. The study also found evidence of exposure to dehydroabietic acid, and exposure levels for resin acids approached 74% of the British OEL for colophony, set at 50 microg/m3. Personal exposure levels to monoterpenes and nitrogen dioxide were low. Area sampling measurements indicated that aldehydes and terpenes were the most abundant VOCs, suggesting that measuring personal exposure to aldehydes might be of interest. Carbon monoxide levels were under the detection limit in all area measurements. High wood dust exposure levels are likely to have

  14. Bile acid sequestrants : more than simple resins

    NARCIS (Netherlands)

    Out, Carolien; Groen, Albert K.; Brufau, Gemma

    Purpose of review Bile acid sequestrants (BAS) have been used for more than 50 years in the treatment of hypercholesterolemia. The last decade, bile acids are emerging as integrated regulators of metabolism via induction of various signal transduction pathways. Consequently, BAS treatment may exert

  15. Adsorption of uranium ions by crosslinked polyester resin functionalized with acrylic acid from aqueous solutions

    International Nuclear Information System (INIS)

    Cemal Oezeroglu; Niluefer Metin

    2012-01-01

    In this paper, the crosslinked polyester resin containing acrylic acid functional groups was used for the adsorption of uranium ions from aqueous solutions. For this purpose, the crosslinked polyester resin of unsaturated polyester in styrene monomer (Polipol 353, Poliya) and acrylic acid as weight percentage at 80 and 20%, respectively was synthesized by using methyl ethyl ketone peroxide (MEKp, Butanox M60, Azo Nobel)-cobalt octoate initiator system. The adsorption of uranium ions on the sample (0.05 g copolymer and 5 mL of U(VI) solution were mixed) of the crosslinked polyester resin functionalized with acrylic acid was carried out in a batch reactor. The effects of adsorption parameters of the contact time, temperature, pH of solution and initial uranium(VI) concentration for U(VI) adsorption on the crosslinked polyester resin functionalized with acrylic acid were investigated. The adsorption data obtained from experimental results depending on the initial U(VI) concentration were analyzed by the Freundlich, Langmuir and Dubinin-Radushkevich (D-R) adsorption isotherms. The adsorption capacity and free energy change were determined by using D-R isotherm. The obtained experimental adsorption data depending on temperature were evaluated to calculate the thermodynamic parameters of enthalpy (ΔH o ), entropy (ΔS o ) and free energy change (ΔG o ) for the U(VI) adsorption on the crosslinked polyester resin functionalized with acrylic acid from aqueous solutions. The obtained adsorption data depending on contact time were analyzed by using adsorption models such as the modified Freundlich, Elovich, pseudo-first order and pseudo-second-order kinetic models. (author)

  16. Surface roughness of composite resins subjected to hydrochloric acid.

    Science.gov (United States)

    Roque, Ana Carolina Cabral; Bohner, Lauren Oliveira Lima; de Godoi, Ana Paula Terossi; Colucci, Vivian; Corona, Silmara Aparecida Milori; Catirse, Alma Blásida Concepción Elizaur Benitez

    2015-01-01

    The purpose of this study was to determine the influence of hydrochloric acid on surface roughness of composite resins subjected to brushing. Sixty samples measuring 2 mm thick x 6 mm diameter were prepared and used as experimental units. The study presented a 3x2 factorial design, in which the factors were composite resin (n=20), at 3 levels: microhybrid composite (Z100), nanofilled composite (FiltekTM Supreme), nanohybrid composite (Ice), and acid challenge (n=10) at 2 levels: absence and presence. Acid challenge was performed by immersion of specimens in hydrochloric acid (pH 1.2) for 1 min, 4 times per day for 7 days. The specimens not subjected to acid challenge were stored in 15 mL of artificial saliva at 37 oC. Afterwards, all specimens were submitted to abrasive challenge by a brushing cycle performed with a 200 g weight at a speed of 356 rpm, totaling 17.8 cycles. Surface roughness measurements (Ra) were performed and analyzed by ANOVA and Tukey test (p≤0.05). Surface roughness values were higher in the presence (1.07±0.24) as compared with the absence of hydrochloric acid (0.72±0.04). Surface roughness values were higher for microhybrid (1.01±0.27) compared with nanofilled (0.68 ±0.09) and nanohybrid (0.48±0.15) composites when the specimens were not subjects to acid challenge. In the presence of hydrochloric acid, microhybrid (1.26±0.28) and nanofilled (1.18±0,30) composites presents higher surface roughness values compared with nanohybrid (0.77±0.15). The hydrochloric acid affected the surface roughness of composite resin subjected to brushing.

  17. Synthesis of iminodi(methylphosphonic acid)-type chitosan resin and its adsorption behavior for trace metals

    International Nuclear Information System (INIS)

    Yamakawa, Satoko; Oshita, Koji; Sabarudin, Akhmad; Oshima, Mitsuko; Motomizu, Shoji

    2004-01-01

    A chitosan-based resin possessing the iminodi(methyphosphonic acid) moiety (IDP-type chitrosan resin) was synthesized by using cross-linked chitosan as a base material. The adsorption behavior of trace metal ions on the IDP-type chitosan resin was systematically investigated using a mini-column (1 ml of the resin) packed with the resin. The concentrations of metal ions in the effluents were measured by ICP-MS and ICP-AES. The resin could adsorb four metals, such as In(III), Sn(II), Th(IV), and U(VI), by almost 100% over a wide pH range (1-7). Uranium(VI) and thorium could not be eluted with nitric acid and hydrochloric acid (1-6 M); other metal ions were easily and readily eluted with 1 M nitric acid. The IDP-type chitosan resin synthesized in this work can be applied to the separation of U(VI) and Th(IV) from other metal ions. (author)

  18. Concentration-Purification of Uranium from an Acid Leaching Solution

    Science.gov (United States)

    Guettaf, H.; Becis, A.; Ferhat, K.; Hanou, K.; Bouchiha, D.; Yakoubi, K.; Ferrad, F.

    2009-11-01

    Chemical processes for the elaboration of uranium concentrate from uranium ore have been studied. This process is composed of successive units operations: crushing, milling, acid conventional leaching, filtration-washing, purification-concentration by ion exchange resins and uranium precipitation. The acid leaching operating conditions allow us to obtain a recovery uranium rate of 93%. The uranium concentration of the pregnant solution is approximately of 1.2 g/l. This value justifies the use of ion exchange resins to the concentration-purification of our pregnant solution. We have noticed that the pregnant solution contains a relatively high phosphate concentration which causes a premature uranium precipitation at pH=1.8. This pH value is in general, considered optimal to obtain the highest amount of fixed uranium by the anionic resin. To avoid the precipitation of uranium, the pH=1.5 has been fixed. We have obtained at this condition a good adsorption capacity. A 75% uranium concentrate have been elaborated, but the filtration of this concentrate has been very difficult. We have also noticed an excessive sulphate concentration. In order to improve this process, we have tested nitrates as eluant at different operating conditions.

  19. Sorption Efficiency of a New Sorbent towards Cadmium(II: Methylphosphonic Acid Grafted Polystyrene Resin

    Directory of Open Access Journals (Sweden)

    Nacer Ferrah

    2013-01-01

    Full Text Available A new chelating polymeric sorbent has been developed using polystyrene resin grafted with phosphonic acid. After characterization by FTIR and elementary analysis, the new resin has been investigated in liquid-solid extraction of cadmium(II. The results indicated that phosphonic resin could adsorb Cd(II ion effectively from aqueous solution. The adsorption was strongly dependent on the pH of the medium and the optimum pH value level for better sorption was between 3.2 and 5.2. The influence of other analytical parameters including contact time, amount of resin, metal ion concentration, and the presence of some electrolytes was investigated. The maximum uptake capacity of Cd(II ions was 37,9 mg·g−1 grafted resin at ambient temperature, at an initial pH value of 5.0. The overall adsorption process was best described by pseudo second-order kinetic. When Freundlich and Langmuir isotherms were tested, the latter had a better fit with the experimental data. Furthermore, more than 92% of Cd(II could be eluted by using 1.0 mol·L−1 HCl in one cycle.

  20. Adsorption Equilibrium Equation of Carboxylic Acids on Anion-Exchange Resins in Water.

    Science.gov (United States)

    Kanazawa, Nobuhiro; Urano, Kohei; Kokado, Naohiro; Urushigawa, Yoshikuni

    2001-06-01

    The adsorption of propionic acid and benzoic acid on anion-exchange resins was analyzed, and an adsorption equilibrium equation of carboxylic acids was proposed. The adsorption of carboxylic acids on the anion-exchange resins was considered to be the sum of the physical adsorption of the molecule and the ion-exchange adsorption of the ion, which were independent of each other. For the physical adsorption of carboxylic acids, it was conformed to the Freundlich equation. For the ion-exchange adsorption of carboxylate ions, the equilibrium equation corresponded well with the experimental results for wide ranges of concentration and pH. The equation contains a selectivity coefficient S(A)(Cl) for the chloride ion versus the carboxylate ion, which was considered essentially a constant. The influent of the bicarbonate ion from carbon dioxide in air could also be expressed by the additional equilibrium equation with the selectivity coefficient S(HCO(3))(Cl) for the chloride ion versus the bicarbonate ion. Consequently, an adsorption equilibrium equation can estimate the equilibrium adsorption amounts. Even the effect of a coexisting bicarbonate ion is inconsequential when the parameters of the Freundlich isotherm equation and the selectivity coefficients of the carboxylate ion and the bicarbonate ion in each resin are determined in advance. Copyright 2001 Academic Press.

  1. Removal of dyes from water using crosslinked aminomethane sulfonic acid based resin.

    Science.gov (United States)

    Kaner, Damla; Saraç, Ayfer; Senkal, Bahire Filiz

    2010-08-01

    A new polymeric resin with amino sulfonic acid pendant functions has been prepared for the extraction of acidic and basic dyes from water. Beaded polymer supports were prepared by suspension polymerization of vinyl benzyl chloride (0.9 mol) and ethylene glycol dimethacrylate (0.1 mol). The resulting copolymer beads were modified with amino methane sulfonic acid. The dye adsorption capacity of the resin was found as 0.16 g dye/g resin for ramazol black and 0.15 g dye/g resin for crystal violet. The pH depending measurements and dye sorption kinetics of the resin were also investigated.

  2. Oxidation-resistant acidic resins prepared by partial carbonization as cocatalysts in synthesis of adipic acid.

    Science.gov (United States)

    Wei, Huijuan; Li, Hongbian; Liu, Yangqing; Jin, Peng; Wang, Xiangyu; Li, Baojun

    2012-08-01

    The oxidation-resistant acidic resins are of great importance for the catalytic oxidation systems. In this paper, the oxidatively stable acidic resins are obtained from the cation ion exchange resins (CIERs) through the thermal treatment in N(2) atmosphere. The structure and properties of the thermally treated CIERs were characterized by chemical analysis, Fourier transform infrared (FT-IR) spectra, acid capacity measurement and scanning electron microscope (SEM). The thermally treated CIERs possess high acid capacity up to 4.09 mmol g(-1). A partial carbonization is observed in the thermal treatment process of CIERs, but the morphology of resin spheres maintains well. The as-prepared CIERs are used as solid acids to assist the hydrogen peroxide oxidation of cyclohexene to adipic acid (ADA) with tungstic acid as the catalyst precursor. The improved yields of ADA in the recycling reaction are obtained in the presence of acidic CIERs. Meanwhile, the unproductive decomposition of H(2)O(2) is effectively suppressed. The high yields of ADA (about 81%) are kept by the thermally treated CIERs even after the fifth cycle. The thermally treated CIERs exhibit excellent acid-catalytic performance and possess remarkable oxidation-resistant capability.

  3. Removing and recovering of uranium from the acid mine waters by using ion exchange resin

    International Nuclear Information System (INIS)

    Nascimento, Marcos Roberto Lopes do

    1998-01-01

    Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. In this study the process was used to remove and recovery uranium from acid mine waters at Pocos de Caldas-MG Uranium Mining and Milling Plant. The local mineralogical features, allied to the biogeochemical phenomena, owing to presence of pyrite in the rock piles, moreover another factors, resulting acid drainage with several pollutants, including uranium ranging from 6 to 14 mg/l, as sulfate complex, that can be removed by anionic exchanger. The iron interference is eliminated by lime pretreatment of water, increasing pH from 2.6 to 3.3-3.8 to precipitate this cation, without changing the uranium amount. Eight anionic resins were tested, based on the uranium loading, in sorption studies. Retention time, and pH influence was verified for the exchanger chose. With breakthrough of 1 mg U/L and 10 mg U/l in the feed solution, the uranium decontamination level was 94%. Typical values of loading resin were 20-30 g U/l and 70-90 g SO 4 /l. Uranium elution was done with Na Cl solution. Retention time, saline, and acid concentration were the parameters studied. The concentrate, obtained from the eluate by ammonia precipitation, presented uranium (86,8% as U 3 O 8 ) and impurities within commercial specifications. (author)

  4. Selective Adsorption of Ag+ on a New Cyanuric-Thiosemicarbazide Chelating Resin with High Capacity from Acid Solutions

    Directory of Open Access Journals (Sweden)

    Guo Lin

    2017-11-01

    Full Text Available A new cyanuric-thiosemicarbazid (TSC-CC chelating resin was synthesized and employed to selectively adsorb Ag+ from acid solutions. The effects of acid concentration, initial concentration of Ag+, contact time and coexisting ions were investigated. The optimal acid concentration was 0.5 mol/L. The adsorption capacity of Ag+ reached 872.63 mg/g at acid concentration of 0.5 mol/L. The adsorption isotherm was fitted well with the Langmuir isotherm model and the kinetic data preferably followed the pseudo-second order model. The chelating resin showed a good selectivity for the Ag+ adsorption from acid solutions. Fourier transform infrared (FT-IR, X-ray diffraction (XRD, Scanning electron microscopy/energy dispersive spectrometer (SEM-EDS and X-ray photoelectron spectroscopy (XPS were used to study the adsorption mechanism. The chelating and ionic interaction was mainly adsorption mechanism. The adsorbent presents a great potential in selective recovery Ag+ from acid solutions due to the advantage of high adsorption capacity and adapting strongly acidic condition. The recyclability indicated that the (TSC-CC resin had a good stability and can be recycled as a promising agent for removal of Ag+.

  5. Kinetics of Ethyl Acetate Synthesis Catalyzed by Acidic Resins

    Science.gov (United States)

    Antunes, Bruno M.; Cardoso, Simao P.; Silva, Carlos M.; Portugal, Ines

    2011-01-01

    A low-cost experiment to carry out the second-order reversible reaction of acetic acid esterification with ethanol to produce ethyl acetate is presented to illustrate concepts of kinetics and reactor modeling. The reaction is performed in a batch reactor, and the acetic acid concentration is measured by acid-base titration versus time. The…

  6. SPE and HPLC/UV of resin acids in colophonium-containing products.

    Science.gov (United States)

    Nilsson, Ulrika; Berglund, Naghmeh; Lindahl, Fredrik; Axelsson, Sara; Redeby, Theres; Lassen, Pia; Karlberg, Ann-Therese

    2008-08-01

    A new method, involving SPE and HPLC/UV diode-array detection (DAD), was developed for the quantification of colophonium components in different consumer products, such as cosmetics. Colophonium is a common cause of contact dermatitis since its components can oxidize into allergens on exposure to air. Three different resin acids were used as markers for native and oxidized colophonium, abietic acid (AbA), dehydroabietic acid (DeA), and 7-oxodehydroabietic acid (7-O-DeA). The SPE method, utilizing a mixed-mode hydrophobic and anion exchange retention mechanism, was shown to yield very clean extracts. The use of a urea-embedded C(12) HPLC stationary phase improved the separation of the resin acids compared to common C(18). Concentrations higher than 2 mg/g of both AbA and DeA were detected in wax strips. In this product also 7-O-DeA, a marker for oxidized colophonium, was detected at a level of 28 microg/g. The LODs were in the range of 7-19 microg/g and the LOQs 22-56 microg/g. The method is simple to use and can be applied on many types of technical products, not only cosmetics. For the first time, a method for technical products was developed, which separates AbA from pimaric acid.

  7. Uranium(VI) adsorption properties of a chelating resin containing polyamine-substituted methylphosphonic acid moiety

    International Nuclear Information System (INIS)

    Matsuda, Masaaki; Akiyoshi, Yoshirou

    1991-01-01

    Uranium(VI) adsorption and desorption properties of a chelating resin containing polyamine-substituted methylphosphonic acid moiety of 2.29 mmol/g-resin (APA) were examined. Uranium(VI) adsorption properties of several ion exchange resins and extractant agents which were known as excellent adsorbents for uranium(VI), were examined together for a comparison with those of APA. Uranium(VI) adsorption capacity of APA at the concentration of 100 mg·dm -3 -uranium(VI) in 100 g·dm -3 -H 2 SO 4 aq. soln., 190 g·dm -3 -H 3 PO 4 aq. soln. and uranium enriched sea water, was 0.2, 0.05 and 0.05 mmol·g -1 respectively. The adsorption capacity of APA for uranium(VI) in these solutions was larger than that of another adsorbents, except the adsorption of uranium(VI) in enriched sea water on ion exchange resin containing phosphoric acid moiety (adsorption capacity ; 0.2 mmol·g -1 ). Uranium(VI) adsorption rate on APA was high and the relation between treatment time (t : min) and uranium(VI) concentration (y : mg·dm -3 ) in 100 g·dm -3 H 2 SO 4 aq. soln. after treatment, was shown as following equation, y=20 0.048t+1.90 (0≤t≤30). The adsorbed uranium(VI) on APA was able to be eluted with a mixed aq. soln. of hydrogen peroxide and sodium hydroxide and also was able to be eluted with an aq. alkaline soln. dissolved reduction agents such as sodium sulfite and hydrazine. From these results, it was thought that uranium(VI) adsorbed on APA was eluted due to the reduction to uranium(VI) by these eluents. (author)

  8. Surface Engineering of PAMAM-SDB Chelating Resin with Diglycolamic Acid (DGA) Functional Group for Efficient Sorption of U(VI) and Th(IV) from Aqueous Medium

    Energy Technology Data Exchange (ETDEWEB)

    Ilaiyaraja, P.; Venkatraman, B., E-mail: chemila07@gmail.com [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Deb, A.K. Singha [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India); Ponraju, D. [Safety Engineering Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India); Ali, Sk. Musharaf [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

    2017-04-15

    Highlights: • A new DGA-PAMAM-SDB chelating resin has been synthesized for actinide sorption. • Maximum sorption capacities of resin are 682 and 544.2 mg g{sup −1}for U(VI) and Th(IV). • DGA-PAMAM-SDB chelating resin could be regenerated and reused. • DFT calculation of actinides interaction with resin corroborates the experimental. • Resin is effective for sorption of actinides from both aqueous and HNO{sub 3} medium. - Abstract: A novel chelating resin obtained via growth of PAMAM dendron on surface of styrene divinyl benzene resin beads, followed by diglycolamic acid functionalization of the dendrimer terminal. Batch experiments were conducted to study the effects of pH, nitric acid concentration, amount of adsorbent, shaking time, initial metal ion concentration and temperature on U(VI) and Th(IV) adsorption efficiency. Diglycolamic acid terminated PAMAM dendrimer functionalized styrene divinylbenzene chelating resin (DGA-PAMAM-SDB) is found to be an efficient candidate for the removal of U(VI) and Th(IV) ions from aqueous (pH > 4) and nitric acid media (> 3 M). The sorption equilibrium could be reached within 60 min, and the experimental data fits with pseudo-second-order model. Langmuir sorption isotherm model correlates well with sorption equilibrium data. The maximum U(VI) and Th(IV) sorption capacity onto DGA-PAMAMG{sub 5}-SDB was estimated to be about 682 and 544.2 mg g{sup −1} respectively at 25 °C. The interaction of actinides and chelating resin is reversible and hence, the resin can be regenerated and reused. DFT calculation on the interaction of U(VI) and Th(IV) ions with chelating resin validates the experimental findings.

  9. Bituminization of simulated waste, spent resins, evaporator concentrates and animal ashes by extrusion process

    International Nuclear Information System (INIS)

    Grosche Filho, C.E.; Chandra, U.

    1987-01-01

    The results of the study of bituminization of simulated radwaste - spennt ion-exchange resins, borate evaporator/concentrates and animal ashes, are presented and discussed. Distilled and oxidizer bitumen were used. Characterization of the crude material and simulated wastes-bitumen mixtures of varying weigt composition (30, 40, 50, 60% by weight of dry waste material) was carried out. The asphaltene and parafin contents in the bitumens were also determined. Some additives and were used with an aim to improve the characteristcs of solidified wastes. For leaching studies, granular ion-exchange resins were with Cs - 134 and mixtures of resin-bitumen were prepared. The leaching studies were executed using the IAEA recommendation and the ISO method. A conventional screw-extruder, common in plastic industry, was used determine operational parameters and process difficulties. Mixtures of resin-bitumen and evaporator concentrate-bitumen obtained from differents operational conditions were characterized. (Author) [pt

  10. Preparation and characterization of manganese dioxide impregnated resin for radionuclide pre-concentration

    Energy Technology Data Exchange (ETDEWEB)

    Varga, Zsolt [Radiation Safety Department, Institute of Isotopes, Hungarian Academy of Sciences, Konkoly-Thege utca 29-33, H-1121, Budapest (Hungary)], E-mail: varga@iki.kfki.hu

    2007-10-15

    An easy and reproducible preparation of manganese dioxide impregnated resin of homogeneous particles has been described. The characteristics of radium, thorium, uranium and plutonium uptake (pH dependency, kinetic studies and matrix dependency) have been determined in batch mode. The resin due to its high efficiency for radium, uranium and thorium at neutral pH values can be an effective tool for radionuclide pre-concentration from liquid samples even with high dissolved solid content.

  11. Determination of the effective anticandidal concentration of denture cleanser tablets on some denture base resins

    Directory of Open Access Journals (Sweden)

    Yeliz Hayran

    2018-01-01

    Full Text Available Abstract Objective Although the effectiveness of chemical cleansing against Candida albicans biofilm has been shown, the effective concentration of denture cleanser tablets has not been studied. The aim of this study was to assess the effect of three denture materials against Candida albicans biofilm and to determine effective concentrations of denture cleanser tablets. Material and methods The surface-roughness of Acron-hi™, QC-20™ and Deflex™ (n=45 per resin resins was standardized by using a profilometer and their contact angle or surface free energy was calculated. C. albicans biofilm was formed on all three resins and were treated with Polident 3 min™, Corega™ and Fittydent™ cleanser solutions at various concentrations and both resin-biofilm and cleanser-biofilm interest were determined by using a MTT protocol according to the European Committee on Antimicrobial Susceptibility Testing's antifungal susceptibility testing (AFST-EUCAST. Scanning electron microscopy was used to compare the efficacy of different resin materials against C. albicans biofilm. Anticandidal activity and surface free energy statistical parameters were calculated by using 3-way and 1-way ANOVA, respectively (p<0.05. Results Polident 3 min™ and Corega™ tablets significantly inhibited (p<0.05 the proliferation of C. albicans against all denture resins at 27-37 mg/mL. Scanning electron microscopy results indicated that there was no significant difference among resin specimens regarding biofilm formation on dentures. We failed to find a significant relationship between surface free energy and the anticandidal effect of resin types. However, the polarity value of the resins was statistically associated with their anticandidal activity. Conclusions The polarity of the resins, the concentrations of tablets and the chemical content of the cleanser may directly affect C. albicans biofilm formations. Polident 3 min™ and Corega™ tablets should be suggested for

  12. Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

    International Nuclear Information System (INIS)

    Keskin, Ali; Yasar, Abdulkadir; Guerue, Metin; Altiparmak, Duran

    2010-01-01

    In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO x emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO 2 emissions did not vary with the blend fuels significantly.

  13. Usage of methyl ester of tall oil fatty acids and resinic acids as alternative diesel fuel

    Energy Technology Data Exchange (ETDEWEB)

    Keskin, Ali; Yasar, Abdulkadir [Tarsus Technical Education Faculty, Mersin University, 33500 Mersin (Turkey); Guerue, Metin [Engineering and Architectural Faculty, Gazi University, 06570 Maltepe, Ankara (Turkey); Altiparmak, Duran [Technical Education Faculty, Gazi University, 06500 Ankara (Turkey)

    2010-12-15

    In the experimental study, tall oil fatty and resinic acids were investigated as alternative diesel fuels. The fatty acids, obtained by distilling the crude tall oil, were esterified with methanol in order to obtain tall oil methyl ester (biodiesel). Blends of the methyl ester, resinic acids and diesel fuel were prepared for test fuels. Performance and emission tests of the test fuels were carried out in an unmodified direct injection diesel engine on full load conditions. The results showed that the specific fuel consumption (SFC) with the blend fuels did not show a significant change. CO emission and smoke level decreased up to 23.91% and 19.40%, respectively. In general, NO{sub x} emissions showed on trend of increasing with the blend fuels (up to 25.42%). CO{sub 2} emissions did not vary with the blend fuels significantly. (author)

  14. Effect of Hydrochloric Acid Concentration on the Conversion of Sugarcane Bagasse to Levulinic Acid

    Science.gov (United States)

    Anggorowati, Heni; Jamilatun, Siti; Cahyono, Rochim B.; Budiman, Arief

    2018-01-01

    Levulinic acid is a new green platform chemical used to the synthesis of a variety of materials for numerous applications such as fuel additives, polymers and resins. It can be produced using renewable resources such as biomass like sugarcane bagasse which are cheap and widely available as waste in Indonesia. In this study, sugarcane bagasse was hydrolyzed using hydrochloric acid with a solid liquid ratio 1:10. The effects of hydrochloric acid concentration at temperature of 180 °C and reaction time of 30 min were studied. The presence of levulinic acid in product of hydrolysis was measured with gas chromatography (GC). It was found that the highest concentration of levulinic acid was obtained at 1 M hydrochloric acid in 25.56 yield%.

  15. Concentrating cesium-137 from seawater using resorcinol-formaldehyde resin for radioecological monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Egorin, Andrei; Tokar, Eduard; Tutov, Mikhail; Avramenko, Valentin [Institute of Chemistry FEBRAS, Vladivostok (Russian Federation); Far Eastern Federal Univ., Vladivostok (Russian Federation); Palamarchuk, Marina; Marinin, Dmitry [Institute of Chemistry FEBRAS, Vladivostok (Russian Federation)

    2017-04-01

    A method of preconcentrating cesium-137 from seawater using a resorcinol-formaldehyde resin, which enables one to optimize the ecological monitoring procedure, has been suggested. Studies of sorption of cesium-137 from seawater by resorcinol-formaldehyde resin have been performed, and it has been demonstrated that the cation exchanger is characterized by high selectivity with respect to cesium-137. It was found that the selectivity depended on the temperature of resin solidification and the seawater pH value. The maximal value of the cesium-137 distribution coefficient is equal to 4.1-4.5 x 10{sup 3} cm{sup 3} g{sup -1}. Under dynamic conditions, the ion-exchange resin capacity is 310-910 bed volumes depending on the seawater pH, whereas the efficiency of cesium removal exceeds 95%. The removal of more than 95% of cesium-137 has been attained using 1-3 M solutions of nitric acid: here, the eluate volume was 8-8.4 bed volumes. Application of 3 M solution of nitric acid results in resin degradation with the release of gaseous products.

  16. Studies concerning the anion ex-change resins catalyzed esterification of epichlorohydrin with organic acids

    Directory of Open Access Journals (Sweden)

    E.I. Muresan

    2009-09-01

    Full Text Available The paper studies the esterification of carboxylic acids with epichlorohydrin over two macroporous strong base anion exchange resins with different polymer matrix. For both resins, the influence of reaction parameters (temperature, catalyst loading, molar ratio on the reaction rate and the yields of the two isomeric esters were investigated.

  17. Influence of hydrofluoric acid on extraction of thorium using a commercially available extraction chromatographic resin.

    Science.gov (United States)

    Shimada-Fujiwara, Asako; Hoshi, Akiko; Kameo, Yutaka; Nakashima, Mikio

    2009-05-01

    The dependence of Th recovery on hydrofluoric acid (HF) concentration in nitric acid (HNO(3)) solutions (1-5 mol/dm(3)) containing 1x10(-6) mol/dm(3) of Th and various concentrations of HF and the elution behavior were studied using a commercially available UTEVA (for uranium and tetravalent actinide) resin column. Thorium recovery decreased with an increase in HF concentration in the sample solutions. The concentration of HF at which Th recovery started to decrease was approximately 1x10(-4) mol/dm(3) in 1 mol/dm(3) HNO(3) solution, approximately 1x10(-3) mol/dm(3) in 3 mol/dm(3) HNO(3) solution, and approximately 1x10(-2) mol/dm(3) in 5 mol/dm(3) HNO(3) solution. When Al(NO(3))(3) (0.2 mol/dm(3)) or Fe(NO(3))(3) (0.6 mol/dm(3)) was added as a masking agent for F(-) to the Th solution containing 1x10(-1) mol/dm(3) HF and 1 mol/dm(3) HNO(3), Th recovery improved from 1.4+/-0.3% to 95+/-5% or 93+/-3%. Effective extraction of Th using UTEVA resin was achieved by selecting the concentration of HNO(3) and/or adding masking agents such as Al(NO(3))(3) according to the concentration of HF in the sample solution.

  18. Development of melamine modified urea formaldehyde resins based o nstrong acidic pH catalyzed urea formaldehyde polymer

    Science.gov (United States)

    Chung-Yun Hse

    2009-01-01

    To upgrade the performance of urea-formaldehyde (UF) resin bonded particleboards, melamine modified urea-formaldehyde (MUF) resins based on strong acidic pH catalyzed UF polymers were investigated. The study was conducted in a series of two experiments: 1) formulation of MUF resins based on a UF polymer catalyzed with strong acidic pH and 2) determination of the...

  19. Separation of chlorogenic acid from honeysuckle crude extracts by macroporous resins.

    Science.gov (United States)

    Zhang, Bin; Yang, Ruiyuan; Zhao, Yan; Liu, Chun-Zhao

    2008-05-15

    Chlorogenic acid, one of the most bioactive compounds rich in the Chinese medicinal herb honeysuckle, is a natural antioxidant and serves as anti-inflammatory, anti-tumor, anti-mutagenic and anti-carcinogenic agent. An efficient preparative separation process of chlorogenic acid from honeysuckle crude extracts has been developed in the present study. HPD-850 resin offers the best adsorption capacity, and adsorption and desorption ratios for chlorogenic acid among the nine macroporous resins tested, and its adsorption rate at 25 degrees C fit best to the Langmuir isotherm. The adsorption capacity of HPD-850 resin was found to depend strongly on the pH value of the initial adsorption solution. The dynamic adsorption and desorption experiments have been carried out on a HPD-850 resin packed column to optimize the separation process of chlorogenic acid from honeysuckle crude extracts. After one run treatment with HPD-850 resin, the chlorogenic acid content in the final product was increased 4.46-fold from 11.2% to 50.0%, with a recovery yield of 87.9%. The preparative separation of chlorogenic acid can be easily and efficiently achieved via adsorption and desorption on HPD-850 resin, and the method developed will provide a potential approach for large-scale separation and purification of chlorogenic acid for its wide pharmaceutical use.

  20. Industrial alkyd resins: characterization of pentaerythritol and phthalic acid esters using integrated mass spectrometry.

    Science.gov (United States)

    La Nasa, Jacopo; Degano, Ilaria; Modugno, Francesca; Colombini, Maria Perla

    2015-02-15

    Alkyd resins are synthetic polyesters used as paints and coatings. Current approaches for their analysis do not allow the characterization of pentaerythritol and phthalic acid esters, whose detection is interesting to fully characterize the materials, e.g. for forensic or cultural heritage applications. A combined analytical approach based on Gas Chromatography/Mass Spectrometry (GC/MS), High-Performance Liquid Chromatography (HPLC)/MS and flow injection analysis (FIA)/MS was adopted. GC/MS was used to characterize the fatty acid profile and the polybasic acids in extracts from industrial alkyd resins. HPLC/MS and FIA/MS were used for the characterization of the triglyceride profile of the oil used to manufacture the resin and for the identification of reaction products deriving from the synthesis process. The multi-analytical approach was applied on two different industrial alkyd resins produced from two different oils. The GC/MS analysis was successful in characterizing the fatty acid profile and the aromatic fraction of the resin. The HPLC/MS analysis allowed us to characterize the pentaerythritol and phthalic acid ester and the triglycerides residues from the synthesis process, by studying their high-resolution tandem mass spectra. The application of liquid chromatography coupled with high-resolution tandem mass spectrometry to the study of industrial alkyd resins allowed us to characterize for the first time the esters formed by the transesterification reactions involving pentaerythritol, phthalic acid and triglycerides. Copyright © 2014 John Wiley & Sons, Ltd.

  1. Characterization of hydroxybenzoic acid chelating resins: equilibrium, kinetics, and isotherm profiles for Cd(II and Pb(II uptake

    Directory of Open Access Journals (Sweden)

    BHAVNA A. SHAH

    2011-06-01

    Full Text Available Chelating ion-exchange resins were synthesized by polycondensation of ortho/para hydroxybenzoic acid with resorcinol/catechol employing formaldehyde as cross-linking agent at 80±5 °C in DMF. The resins were characterized by FTIR and XRD. The uptake behaviour of synthesized resins for Cd(II and Pb(II ions have been studied depending on contact time, pH, metal ion concentration and temperature. The sorption data obtained at optimized conditions were analyzed by the Langmuir and Freundlich isotherms. Experimental data of all metal–resin system were best represented by the Freundlich isotherm. The maximum obtained sorption capacity for cadmium was 69.53 mg g-1 and 169.32 mg g-1 for Lead. The adsorption process follows first order kinetics and the specific rate constant Kr was obtained by the application of the Lagergan equation. Thermodynamic parameters ∆Gads, ∆Sads and ∆Hads were calculated for the metal–resin systems. The external diffusion rate constant (KS and the intra-particle diffusion rate constant (Kid were calculated by the Spahn–Schlunder and Weber–Morris models, respectively. The sorption process was found to follow an intra-particle diffusion phenomenon.

  2. (Methacrylic Acid-Co-Divinylbenzene) Resin as Filler

    African Journals Online (AJOL)

    divinylbenzene) resin (PMD) as a new filler-binder for direct compression tablets. Methods: Powder properties of PMD and MCC were characterized. Tablets made from PMD and MCC with and without propranolol hydrochloride were evaluated for ...

  3. Selected resin acids in effluent and receiving waters derived from a bleached and unbleached kraft pulp and paper mill

    Science.gov (United States)

    Quinn, B.P.; Booth, M.M.; Delfino, J.J.; Holm, S.E.; Gross, T.S.

    2003-01-01

    Water samples were collected on three dates at 24 sites influenced by effluent from Georgia-Pacific's Palatka Pulp and Paper Mill Operation, a bleached and unbleached kraft mill near Palatka, Florida, USA. The sampling sites were located within the mill retention ponds, Rice Creek, and the St. John's River. Samples were analyzed by gas chromatography-mass spectrometry for abietic, dehydroabietic, and isopimaric acids, all of which are potentially toxic by-products of pulp production. Isopimaric acid concentrations greater than 12 mg/L were measured at the mill's effluent outfall but were less than 20 ??g/L at the end of Rice Creek. This result indicates that the waters of Rice Creek provide dilution or conditions conducive for degradation or sorption of these compounds. Large differences in resin acid concentrations were observed between sampling events. In two sampling events, the maximum observed concentrations were less than 2 mg/L for each analyte. In a third sampling event, all of the compounds were detected at concentrations greater than 10 mg/L. Data from the three sample dates showed that resin acid concentrations were below 20 ??g/L before the confluence of Rice Creek and the St. John's River in all cases.

  4. Gas chromatographic determination of organic acids from fruit juices by combined resin mediated methylation and extraction in supercritical carbon dioxide.

    Science.gov (United States)

    Barden, T J; Croft, M Y; Murby, E J; Wells, R J

    1997-10-17

    A procedure in which anionic analytes, trapped on ion exchange resin, are simultaneously methylated and released using methyl iodide in either supercritical carbon dioxide or acetonitrile has been extended to polyfunctional organic acids. The combined SFE methylation of fruit juice acids trapped onto ion exchange resin proceeds in good yield producing the methyl esters of fumaric, succinic, malic, tartaric, isocitric and citric acids which are readily separated by GC. Using this procedure low concentrations of one acid can be detected and quantitated in the presence of very high concentrations of another. This new method detects tartaric acid at levels of 10 ppm in juices containing 10,000 ppm citric acid. Quantitation was performed either by using GC-FID with triethyl citrate or diethyl tartrate as internal standards or with the element specific calibration capability of the GC-AED. A simple new technique for the determination of citric/isocitric acid ratio is now available. Also, in contrast to HPLC methods, the identity of an analyte is readily confirmed by GC-MS.

  5. SEPARATION AND PRECONCENTRATION OF COPPER (II ION BY FATTY HYDROXAMIC ACIDS IMMOBILIZED ONTO AMBERLITE XAD – 4 RESIN

    Directory of Open Access Journals (Sweden)

    Dedy Suhendra

    2010-06-01

    Full Text Available A method of copper (II ion preconcentration and separation from other ions by using a column containing fatty hydroxamic acids - loaded Amberlite XAD 4 resin (FHA-Amb is described. Several factors, which affect the separation and preconcentration efficiency such as pH, sample volume, and concentration of eluent and flow rate, have been investigated.  A quantitative recovery of copper (II ion from FHA-Amb resin column was obtained using 10% HNO3 solutions as eluent with a preconcentration factor of 60. A method for separation of Cu(II from Zn(II and Cd(II is proposed.  A rapid sample throughput, a clean separation, a high preconcentration factor and simplicity are the main advantages in these analytical procedures.   Keywords: extraction, preconcentration, fatty hydroxamic acid, copper (ii ion, amberlite XAD-4

  6. Adsorption characteristics of 14C-labeled alanine, aspartic acid and adenosine triphosphate by metal-chelating resins

    International Nuclear Information System (INIS)

    Ishiyama, Toshio; Matsunami, Tadao; Shibata, Setsuko; Honda, Yoshihide.

    1987-01-01

    (1) Adsorption properties of 14 C-alanine, 14 C-ATP (adenosine triphosphate) and 14 C-aspartic acid on the metal-chelating resins were determined and found that the Cu(II)-Chelex 100 and Fe(III)-Unicellex UR10, Fe(III)-Chelex 100 chelating resins were highly effective for the adsorption of 14 C-alanine and 14 C-ATP, respectively. (2) Desorption rate of 14 C-ATP from the Fe(III)-Unicellex UR10 and Fe(III)-Chelex 100 resins was somewhat higher than the case of 14 C-alanine, probably because the coordination bonds of Cu-alanine might be stronger than those of Fe-ATP. Thus, 14 C-labeled organic compounds such as 14 C-alanine and 14 C-ATP of a low activity concentration (3.7 mBq/ml) (1 x 10 -7 μCi/ml) in aqueous solution may be measured with liquid scintillation counter after pre-concentration by use of the Fe(III)- and Cu(II)-chelating resin columns. (author)

  7. Resin replica in enamel deproteinization and its effect on acid etching.

    Science.gov (United States)

    Espinosa, Roberto; Valencia, Roberto; Uribe, Mario; Ceja, Israel; Cruz, J; Saadia, Marc

    2010-01-01

    The goal of this in vitro study was to identify the topographical features of deproteinized (NaOCl) and etched with phosphoric acid (H3PO4) enamel surface, compared to phosphoric acid surface alone with a Resin Replica model. Ten extracted lower first and second permanent molars were polished with pumice and water, and then divided into 3 equal buccal sections having similar physical and chemical properties. The enamel surfaces of each group were subjected to the following treatments: Group A: Acid Etching with H3PO4 37% for 15 seconds. Group B: Sodium Hypochlorite (NaOCl) 5.25% for 60 seconds followed by Acid Etching with H3PO4 37% for 15 seconds. Group C; No treatment (control). All the samples were treated as follow: Adhesive and resin were applied to all groups after A, B and C treatment were performed; Then enamel/dentin decalcification and deproteinization and topographic SEM Resin Replica assessment were used to identify resin tags enamel surface quality penetration. Showed that group B reached an area of 7.52 mm of the total surface, with a 5.68 mm2 (73%) resin tag penetration equivalent type I and II etching pattern, 1.71 mm2 (26%) equivalent to type III etching pattern and 0.07 mm2 (1%) unaffected surface. Followed by group A with 7.48 mm2 of the total surface, with a 3.47 mm2 (46 %)resin tag penetration equivalent to type I and II etching pattern, 3.30 mm2 (45%)equivalent to type III etching pattern and 0.71 mm2, and (9%) unaffected surface. Group C did not show any resin tag penetration. A significant statistical diference (P enamel is deproteinizated with 5.25% NaOCl for 1 minute prior H3PO4, the surface and topographical features of the replica resin penetration surface increases significantly with type I-II etching pattern.

  8. Novel bioactive polyester scaffolds prepared from unsaturated resins based on isosorbide and succinic acid

    Energy Technology Data Exchange (ETDEWEB)

    Śmiga-Matuszowicz, Monika, E-mail: monika.smiga-matuszowicz@polsl.pl [Silesian University of Technology, Department of Physical Chemistry and Technology of Polymers, M. Strzody Street 9, 44-100 Gliwice (Poland); Janicki, Bartosz; Jaszcz, Katarzyna; Łukaszczyk, Jan [Silesian University of Technology, Department of Physical Chemistry and Technology of Polymers, M. Strzody Street 9, 44-100 Gliwice (Poland); Kaczmarek, Marcin [Silesian University of Technology, Department of Biomaterials and Medical Devices Engineering, de Gaulle' a Street 66, 41-800 Zabrze (Poland); Lesiak, Marta; Sieroń, Aleksander L. [Medical University of Silesia, Department of General and Molecular Biology and Genetics, Medyków Street 18, 40-752 Katowice (Poland); Simka, Wojciech [Silesian University of Technology, Department of Chemistry, Inorganic Technology and Fuels, B. Krzywoustego Street 6, 44-100 Gliwice (Poland); Mierzwiński, Maciej; Kusz, Damian [Medical University of Silesia, Department of Orthopedics and Traumatology, Ziołowa Street 45, 40-635 Katowice (Poland)

    2014-12-01

    In this study new biodegradable materials obtained by crosslinking poly(3-allyloxy-1,2-propylene succinate) (PSAGE) with oligo(isosorbide maleate) (OMIS) and small amount of methyl methacrylate were investigated. The porous scaffolds were obtained in the presence of a foaming system consisted of calcium carbonate/carboxylic acid mixture, creating in situ porous structure during crosslinking of liquid formulations. The maximum crosslinking temperature and setting time, the cured porous materials morphology as well as the effect of their porosity on mechanical properties and hydrolytic degradation process were evaluated. It was found that the kind of carboxylic acid used in the foaming system influenced compressive strength and compressive modulus of porous scaffolds. The MTS cytotoxicity assay was carried out for OMIS using hFOB1.19 cell line. OMIS resin was found to be non-toxic in wide range of concentrations. On the ground of scanning electron microscopy (SEM) observations and energy X-ray dispersive analysis (EDX) it was found that hydroxyapatite (HA) formation at the scaffolds surfaces within short period of soaking in phosphate buffer solution occurs. After 3 h immersion a compact layer of HA was observed at the surface of the samples. The obtained results suggest potential applicability of resulted new porous crosslinked polymeric materials as temporary bone void fillers. - Highlights: • Isosorbide-based resin was used as a component of biodegradable scaffolds. • CAC/carboxylic acid system was proven as facile method to obtain porous scaffolds. • Porous scaffolds displayed the formation of hydroxyapatite at their surfaces.

  9. Effect of the chemical structure of anion exchange resin on the adsorption of humic acid: behavior and mechanism.

    Science.gov (United States)

    Shuang, Chendong; Wang, Jun; Li, Haibo; Li, Aimin; Zhou, Qing

    2015-01-01

    Polystyrenic (PS) anion-exchange resin and polyacrylic (PA) anion-exchange resin were used to investigate the effect of resin chemical structure on the adsorption of humic acid (HA). Due to the rearrangement of HA to form layers that function as barricades to further HA diffusion, PS resin exhibited 12.4 times slower kinetics for the initial adsorption rate and 8.4 times for the diffusion constant in comparison to that of the PA resin. An HA layer and a spherical cluster of HA can be observed on the surface of the PS and PA resins after adsorption, respectively. The considerable difference in HA adsorption between the PS and PA resins was due to the difference in molecule shape for interaction with different resin structures, which can essentially be explained by the hydrophobicity and various interactions of the PS resin. A given amount of HA occupies more positively charged sites and hydrophobic sites on the PS resin than were occupied by the same amount of HA on the PA resin. Increased pH resulted in an increase of HA adsorption onto the PA resin but a decrease in adsorption onto PS resin, as the non-electrostatic adsorption led to electrostatic repulsion between the HA attached to the resin and the HA dissolved in solution. These results suggest higher rates of adsorption and higher regeneration efficiency for interaction of HA with more hydrophilic anion exchange materials. Copyright © 2014 Elsevier Inc. All rights reserved.

  10. Large scale purification of puerarin from Puerariae Lobatae Radix through resins adsorption and acid hydrolysis.

    Science.gov (United States)

    Guo, Hai-Dong; Zhang, Qing-Feng; Chen, Ji-Guang; Shangguang, Xin-Cheng; Guo, Yu-Xian

    2015-02-01

    Puerarin is the major isoflavone of Puerariae Lobatae Radix. A method for large scale purification of puerarin was developed through resins adsorption and acid hydrolysis. The adsorption properties of six macroporous resins (D101, S-8, H103, X-5, HPD600, AB-8) were compared through the adsorption kinetics and equilibrium adsorption isotherms. Results showed that H103 resin had the best adsorption rate and capacity. The mass transfer zone motion model was further used for analyzing the fixed bed adsorption of H103 resin. Its length of mass transfer zone with 2mg/ml of puerarin in water and 10% ethanol at flow rate of 10ml/min were 41.6 and 47.5cm, while the equilibrium adsorption capacity was 165.03 and 102.88mg/g, respectively. By using 75% ethanol, puerarin could be well desorbed from the resin with recovery of 97.4%. Subsequently, H103 resin was successfully used for puerarin purification from Puerariae Lobatae Radix. The content of total isoflavones and puerarin in the resin adsorption product were 69.25% and 41.78%, respectively, which were about three times increased compared to the crude extract. Then, the product was hydrolyzed by 2.5M HCl at 90°C for 1h. Puerarin with purity of 90% and a byproduct daidzein with purity of 78% were obtained. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Synthesis of hemicellulose-acrylic acid graft copolymer super water absorbent resin by ultrasonic irradiation technology

    Directory of Open Access Journals (Sweden)

    Fangfang LIU

    2015-12-01

    Full Text Available The hemicellulose super water absorbent resin is prepared by using ultrasonic irradiation technology, with the waste liquid produced during the preparation of viscose fiber which contains a large amount of hemicellulose as raw material, acrylic acid as graft monomer, N,N’-methylene bis acrylamide (NMBA as cross linking agent, and (NH42S2O8-NaHSO3 as the redox initiation system. The synthesis conditions, structure and water absorption ability of resin are discussed. The results indicate that water absorbency of the resin is 311 g/g, the tap water absorbency is 102 g/g, the normal saline absorbency is 55 g/g, and the artificial urine absorbency is 31 g/g under the optimal synthesis conditions, so the resin has great water absorption rate and water retaining capacity. The FT-IR and SEM analysis shows that the resin with honeycomb network structure is prepared. The successfully synthesized of the resin means that the hemicellulose waste liquid can be highly effectively recycled, and it provides a kind of new raw material for the synthesis of super water absorbent resin.

  12. Adsorption performance of salicylic acid on a novel resin with distinctive double pore structure.

    Science.gov (United States)

    Xiao, Guqing; Wen, Ruiming; Liu, Aijiao; He, Guowen; Wu, Dan

    2017-05-05

    Two approaches were used to synthesize two resins with different pore structures. In one way, the CH 2 Cl groups in macroporous chloromethylated polystyrene resin were transformed to methylene bridges, and achieved a hypercrosslinked resin with plentiful micropores (denoted GQ-06). In the other way, 50% of the CH 2 Cl groups in chloromethylated polystyrene resin was used to produce micropores, while the residual 50% of the CH 2 Cl groups was reacted with 2-aminopyridine, and prepared another resin with double pore structure of hypercrosslinked resin and macroporous resin (denoted GQ-11). The adsorption of salicylic acid (SA) on GQ-11 was investigated using GQ-06 as the reference adsorbent. The effect of pH on the adsorption of SA on GQ-06 was consistent with the dissociation curve of SA. The maximum adsorption capacity of SA on GQ-11 was observed at the solution pH of 2.64. The greater adsorption rate of SA on GQ-11 than that of GQ-06 was attributed to its double pore structure. The multifunctional adsorption mechanism of anion exchange and hydrophobic interaction resulted in the larger equilibrium capacity of SA on GQ-11 than that of GQ-06. GQ-06 and GQ-11 could be regenerated by absolute alcohol and 80% of alcohol -0.5mol/L of sodium hydroxide aqueous solution, respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. A combined process of activated carbon adsorption, ion exchange resin treatment and membrane concentration for recovery of dissolved organics in pre-hydrolysis liquor of the kraft-based dissolving pulp production process.

    Science.gov (United States)

    Shen, Jing; Kaur, Ishneet; Baktash, Mir Mojtaba; He, Zhibin; Ni, Yonghao

    2013-01-01

    To recover dissolved organics in pre-hydrolysis liquor (PHL) of the kraft-based dissolving pulp production process, a new combined process concept of sequential steps of activated carbon adsorption, ion exchange resin treatment, and membrane concentration, was proposed. The removal of lignin in the PHL was achieved in the activated carbon adsorption step, which also facilitates the subsequent operations, such as the membrane filtration and ion exchange resin treatment. The ion exchange resin treatment resulted in the removal/concentration of acetic acid, which opens the door for acetic acid recovery. The membrane filtration is to recover/concentrate the dissolved sugars. The combined process resulted in the production of PHL-based concentrate with relatively high concentration of hemicellulosic sugars, i.e., 22.13%. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Exposure to acid anhydrides in three resin and one cushioned flooring manufacturing plants.

    Science.gov (United States)

    van Tongeren, M J; Barker, R D; Gardiner, K; Harris, J M; Venables, K M; Taylor, A J; Harrington, J M

    1995-10-01

    Acid anhydrides are reactive organic chemicals of low molecular weight which cause occupational asthma. No previous research on the relationship between exposure to these chemicals and respiratory sensitization and development of occupational asthma has been reported. A retrospective cohort study was carried out in four factories (three alkyd resin factories and one cushioned flooring factory) to investigate the nature of exposure-response relationships for sensitization to phthalic anhydride (PA), trimellitic anhydride (TMA) and maleic anhydride (MA). This paper describes the results of full-shift and task-specific exposure measurements. Exposure to PA was low in relation to the Occupational Exposure Standard (OES). The highest full-shift PA exposures occurred among resin operators in the resin factory that used solid PA as compared to other resin factories where liquid PA was used. Arithmetic mean exposure levels to TMA and MA in the resin factories were well below their respective OESs. Short-term high exposures occurred during loading of acid anhydrides into the reactors and sampling and testing of the resin. Relatively high full-shift exposure to TMA occurred in the cushioned flooring factory, although no high peak exposures were detected.

  15. Flow injection spectrophotometric determination of low concentrations of orthosphate in natural waters employing ion exchange resin

    International Nuclear Information System (INIS)

    Pessenda, L.C.R.

    1981-01-01

    A simple and fast method for the determination of low concentrations of orthophosphate in natural waters is described. Ion exchange is incorporated into a flow injection system by usina a resin column in the sample loop of a proportion injector. Effects of sample aspiration rate, sampling time, eluting agent concentration, pumping rate of the sample carrier stream and interfaces, were investigated both using 32 PO 3- 4 or 31 PO 3- 4 with columns coupled to a gerger-muller detector and incorporated in a flow system with molybdenum blue colorinetry. (M.A.C.) [pt

  16. Sorption of Pu(IV) from nitric acid by bifunctional anion-exchange resins

    International Nuclear Information System (INIS)

    Bartsch, R.A.; Zhang, Z.Y.; Elshani, S.; Zhao, W.; Jarvinen, G.D.; Barr, M.E.; Marsh, S.F.; Chamberlin, R.M.

    1999-01-01

    Anion exchange is attractive for separating plutonium because the Pu(IV) nitrate complex is very strongly sorbed and few other metal ions form competing anionic nitrate complexes. The major disadvantage of this process has been the unusually slow rate at which the Pu(IV) nitrate complex is sorbed by the resin. The paper summarizes the concept of bifunctional anion-exchange resins, proposed mechanism for Pu(IV) sorption, synthesis of the alkylating agent, calculation of K d values from Pu(IV) sorption results, and conclusions from the study of Pu(IV) sorption from 7M nitric acid by macroporous anion-exchange resins including level of crosslinking, level of alkylation, length of spacer, and bifunctional vs. monofunctional anion-exchange resins

  17. Cesium Isotherm Testing with Spherical Resorcinol-Formaldehyde Resin at High Sodium Concentrations

    Energy Technology Data Exchange (ETDEWEB)

    Russell, Renee L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fiskum, Sandra K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Smoot, Margaret R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rinehart, Donald E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-04-01

    Washington River Protection Solutions (WRPS) is developing a Low-Activity Waste Pretreatment System (LAWPS) to provide low-activity waste (LAW) directly to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste Facility for immobilization. The pretreatment that will be conducted on tank waste supernate at the LAWPS facility entails filtration to remove entrained solids and cesium (Cs) ion exchange to remove Cs from the product sent to the WTP. Currently, spherical resorcinol-formaldehyde (sRF) resin (Microbeads AS, Skedsmokorset, Norway) is the Cs ion exchange resin of choice. Most work on Cs ion exchange efficacy in Hanford tank waste has been conducted at nominally 5 M sodium (Na). WRPS is examining the possibility of processing supernatant at high Na concentrations—up to 8 M Na—to maximize processing efficiency through the LAWPS. Minimal Cs ion exchange work has been conducted at 6 M and 8 M Na concentrations..

  18. Solidification of radioactive liquid wastes. A comparison of treatment options for spent resins and concentrates

    International Nuclear Information System (INIS)

    Roth, A.; Willmann, F.; Ebata, M.; Wendt, S.

    2008-01-01

    Ion exchange is one of the most common and effective treatment methods for liquid radioactive waste. However, spent ion exchange resins are considered to be problematic waste that in many cases require special approaches and pre-conditioning during its immobilization to meet the acceptance criteria for disposal. Because of the function that they fulfill, spent ion exchange resins often contain high concentrations of radioactivity and pose special handling and treatment problems. Another very common method of liquid radioactive waste treatment and water cleaning is the evaporation or diaphragm filtration. Both treatment options offer a high volume reduction of the total volume of liquids treated but generate concentrates which contain high concentrations of radioactivity. Both mentioned waste streams, spent resins as well as concentrates, resulting from first step liquid radioactive waste treatment systems have to be conditioned in a suitable manner to achieve stable waste products for final disposal. The most common method of treatment of such waste streams is the solidification in a solid matrix with additional inactive material like cement, polymer etc. In the past good results have been achieved and the high concentration of radioactivity can be reduced by adding the inactive material. On the other hand, under the environment of limited space for interim storage and the absence of a final repository site, the built-up of additional volume has to be considered as very critical. Moreover, corrosive effects on cemented drums during long-term interim storage at the surface have raised doubts about the long-term stability of such waste products. In order to avoid such disadvantages solidification methods have been improved in order to get a well-defined product with a better load factor of wastes in the matrix. In a complete different approach, other technologies solidify the liquid radioactive wastes without adding of any inactive material by means of drying

  19. Crypthophilic acids A, B, and C: resin glycosides from aerial parts of Scrophularia crypthophila.

    Science.gov (United States)

    Caliş, Ihsan; Sezgin, Yükselen; Dönmez, Ali A; Rüedi, Peter; Tasdemir, Deniz

    2007-01-01

    The water-soluble part of the methanolic extract from the aerial parts of Scrophularia crypthophila, through chromatographic methods, yielded three new resin glycosides, crypthophilic acids A - C (1-3). Compounds 1-3 are tetraglycosides of (+)-3S,12S-dihydroxypalmitic acid. The structures of these and 10 known compounds were elucidated by spectroscopic and chemical means. All natural resin glycosides known so far have been obtained from Convolvulaceae plants; this is the first report of such glycosides from another, taxonomically unrelated family (Scrophulariaceae).

  20. Dimerisation of isobutene on acidic ion-exchange resins

    OpenAIRE

    Honkela, Maija

    2005-01-01

    Dimerisation of isobutene produces diisobutenes that can be hydrogenated to isooctane (2,2,4-trimethyl pentane). Isooctane can be used as a high octane gasoline component. The aim of this work was to study the selective production of diisobutenes through the dimerisation of isobutene on ion-exchange resin catalysts and to construct kinetic models for the reactions in the system for reactor design purposes. High selectivities for diisobutenes were obtained in the presence of polar componen...

  1. Chemically modified polymeric resins for separation of cations, organic acids, and small polar moleculea by high performance liquid chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Morris, John B. [Iowa State Univ., Ames, IA (United States)

    1993-07-01

    This thesis is divided into 4 parts: a review, ion chromatography of metal cations on carboxylic resins, separation of hydrophilic organic acids and small polar compounds on macroporous resin columns, and use of eluent modifiers for liquid chromatographic separation of carboxylic acids using conductivity detection.

  2. Hyaluronic acid concentration in liver diseases.

    Science.gov (United States)

    Gudowska, Monika; Gruszewska, Ewa; Panasiuk, Anatol; Cylwik, Bogdan; Flisiak, Robert; Świderska, Magdalena; Szmitkowski, Maciej; Chrostek, Lech

    2016-11-01

    The aim of this study was to evaluate the effect of liver diseases of different etiologies and clinical severity of liver cirrhosis on the serum level of hyaluronic acid. The results were compared with noninvasive markers of liver fibrosis: APRI, GAPRI, HAPRI, FIB-4 and Forn's index. Serum samples were obtained from 20 healthy volunteers and patients suffering from alcoholic cirrhosis (AC)-57 patients, non-alcoholic cirrhosis (NAC)-30 and toxic hepatitis (HT)-22. Cirrhotic patients were classified according to Child-Pugh score. Hyaluronic acid concentration was measured by the immunochemical method. Non-patented indicators were calculated using special formulas. The mean serum hyaluronic acid concentration was significantly higher in AC, NAC and HT group in comparison with the control group. There were significant differences in the serum hyaluronic acid levels between liver diseases, and in AC they were significantly higher than those in NAC and HT group. The serum hyaluronic acid level differs significantly due to the severity of cirrhosis and was the highest in Child-Pugh class C. The sensitivity, specificity, accuracy, positive and negative predictive values and the area under the ROC curve for hyaluronic acid and all non-patented algorithms were high and similar to each other. We conclude that the concentration of hyaluronic acid changes in liver diseases and is affected by the severity of liver cirrhosis. Serum hyaluronic acid should be considered as a good marker for noninvasive diagnosis of liver damage, but the combination of markers is more useful.

  3. Colour spectrum and resin-type determine the concentration and composition of Polycyclic Aromatic Hydrocarbons (PAHs) in plastic pellets.

    Science.gov (United States)

    Fisner, Mara; Majer, Alessandra; Taniguchi, Satie; Bícego, Márcia; Turra, Alexander; Gorman, Daniel

    2017-09-15

    This study assessed the concentration and composition of Polycyclic Aromatic Hydrocarbons (PAHs) in plastic pellets, collected from sandy beaches and considered different resin and colour tones. Results showed that polyethylene pellets, while displaying a greater range of total PAH concentrations did not differ significantly from polypropylene pellets. More importantly, both resin types demonstrated predictable increases in total PAH across a spectrum of darkening colour tones. Multivariate comparisons of 36 PAH groups, further showed considerable variability across resin type and colour, with lighter coloured pellets comprising lower molecular weight, while darker pellets contained higher weight PAHs. Overall, we show predictable variation in PAH concentrations and compositions of plastic pellets of different ages and resin types that will directly influence the potential for toxicological effects. Our findings suggest that monitoring programs should take these attributes into account when assessing the environmental risks of microplastic contamination of marine and coastal habitats. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Effect of sulfuric acid etching of polyetheretherketone on the shear bond strength to resin cements.

    Science.gov (United States)

    Sproesser, Oliver; Schmidlin, Patrick R; Uhrenbacher, Julia; Roos, Malgorzata; Gernet, Wolfgang; Stawarczyk, Bogna

    2014-10-01

    To examine the influence of etching duration on the bond strength of PEEK substrate in combination with different resin composite cements. In total, 448 PEEK specimens were fabricated, etched with sulfuric acid for 5, 15, 30, 60, 90, 120, and 300 s and then luted with two conventional resin cements (RelyX ARC and Variolink II) and one self-adhesive resin cement (Clearfil SA Cement) (n = 18/subgroup). Non-etched specimens served as the control group. Specimens were stored in distilled water for 28 days at 37°C and shear bond strengths were measured. Data were analyzed nonparametrically using Kruskal-Wallis-H (p sulfuric acid seems to be suitable and effective for PEEK surface pre-treatment, further investigations are required to examine the effect of other adhesive systems and cements.

  5. Esterification of oleic acid with ethanol catalyzed by sulfonated cation exchange resin: Experimental and kinetic studies

    International Nuclear Information System (INIS)

    Jiang, Yuwang; Lu, Jie; Sun, Kaian; Ma, Lingling; Ding, Jincheng

    2013-01-01

    Graphical abstract: - Highlights: • Esterification of oleic acid with ethanol was investigated in the presence of sulfonated cation exchange resin. • We studied kinetic model of the esterification of oleic acid with ethanol according to experimental data. • The proposed kinetic model can well predict oleic acid conversion. - Abstract: This paper investigated the effects of ethanol to oleic acid molar ratio, reaction temperature, catalyst loading, water content and catalyst recycling on sulfonated cation exchange resin in a stirred batch reactor under atmospheric pressure. When the esterification was carried out with an ethanol to oleic acid (42.4 g) molar ratio of 9:1, reflux of ethanol at 82 °C, 20 g of catalyst and 8 h of reaction time, the oleic acid conversion rate reached approximately 93%. A pseudo-homogeneous kinetic model for describing the esterification of oleic acid with ethanol by the sulfonated cation exchange resin was developed on the basis of laboratorial results. The kinetic model can well predict the oleic acid conversion

  6. Tape-stripping as a method for measuring dermal exposure to resin acids during wood pellet production.

    Science.gov (United States)

    Eriksson, Kåre; Hagström, Katja; Axelsson, Sara; Nylander-French, Leena

    2008-03-01

    The purpose of this study was to develop a sensitive and specific method for quantifying dermal exposure to the resin acids 7-oxodehydroabietic acid (7-OXO), dehydroabietic acid (DHAA), abietic acid (AA), and pimaric acid (PA). In addition the method was evaluated in occupational settings during production of wood pellets. Tape-strips were spiked with the substances to evaluate the recovery of the acids from the tape. The removal efficiency of the tape was assessed by tape-stripping a specified area on a glass plate spiked with resin acids. The recovery of the acids from human skin in vivo was evaluated by applying acids in methanol onto the skin of volunteers. Occupational dermal exposure to the resin acids was assessed by tape-stripping the skin of workers involved in the production of wood pellets. The resin acids were analyzed by liquid chromatography mass spectrometry (LC-MS). The limit of detection was 15 pg (7-OXO), 150 pg (DHAA), 285 pg (AA) and 471 pg (PA) per injection. The recovery from spiked tapes was in general 100%. The removal efficiency of the tape was 48-101%. Recovery tests from human skin in vivo showed a mean recovery of 27%. Quantifiable amounts of resin acids were observed on four different skin areas with an increase in exposure during a work shift. This study shows that occupational dermal exposure to resin acids can be assessed by tape-stripping and quantified by LC-MS.

  7. Effect of alcohols on elution chromatography of trivalent actinides and lanthanides using tertiary pyridine resin with hydrochloric acid-alcohol mixed solvents.

    Science.gov (United States)

    Ikeda, Atsushi; Suzuki, Tatsuya; Aida, Masao; Fujii, Yasuhiko; Itoh, Keisuke; Mitsugashira, Toshiaki; Hara, Mitsuo; Ozawa, Masaki

    2004-07-02

    Elution chromatography with a tertiary pyridine resin has been used to separate the trivalent actinides (An3+) from the lanthanides (Ln3+) using an alcoholic hydrochloric acid solvent. Trivalent Am and Cm were separated from the Ln by employing a 1 cm(phi) x 10 cm resin column with the mixed solvent system composed of concentrated hydrochloric acid (HCl) and alcohols. The distribution coefficients (Kd) and the separation factors between An and Ln (alpha(An)(Ln)) increased as the alcohol content of the solvent mixture increased. On the other hand, the Kd and alpha(An)(Ln) decreased drastically upon the addition of water to the solvent mixture. Among the four alcohols investigated (methanol, ethanol, n-propanol and n-butanol), the ethanol-HCl mixed solvent system showed the largest Kd and alpha(An)(Ln). The mechanism of adsorption for An and Ln cations on the pyridine resin is discussed in addition to the results presented herein.

  8. Separation of Technetium in Nitric Acid Solution With an Extractant Impregnated Resin

    International Nuclear Information System (INIS)

    Jei Kwon Moon; Eil Hee Lee; Chong-Hun Jung; Byung Chul Lee

    2006-01-01

    An extractant impregnated resin (EIR) was prepared by impregnation of Aliquat 336 into Amberlite XAD-4 for separation of technetium from rhodium in nitric acid solution. The prepared EIR showed high preference for rhenium (chemical analogue of technetium) over rhodium. The adsorption isotherms for rhenium were described well by Langmuir equation in both the single and multi-component systems. Maximum adsorption capacities obtained by modelling the isotherms of rhenium were 2.01 meq g -1 and 1.97 meq g -1 for the single and the multi-component systems, respectively. Column tests were also performed to confirm the separation efficiency of rhenium using a jacketed glass column (diam. 11 x L 150). The EIR column showed successful separation of rhenium with the breakthrough volume of about 122 BV for the breakthrough concentration of 0.08. Also the breakthrough data were modelled successfully by assuming a homogeneous diffusion model in the particle phase. The diffusivities obtained from the modelling were in the order of 10 -7 cm 2 min -1 for a rhenium. The rhenium adsorbed on the bed could be eluted with a high purity by using a nitric acid solution. (authors)

  9. Effective adsorption of nitroaromatics at the low concentration by a newly synthesized hypercrosslinked resin.

    Science.gov (United States)

    Wang, Chuanhong; Xu, Chao; Sun, Weizhi; Liu, Fusheng; Yu, Shitao; Xian, Mo

    2017-11-01

    In the present study, a series of hypercrosslinked resins (CH series) was prepared in systematically designed conditions for the adsorption of nitroaromatics from aqueous solution. The newly synthesized CH-10 possesses a Brunauer-Emmett-Teller (BET) surface area up to 1,329.3 m 2 /g which is larger than that of the widely used hypercrosslinked resin H-103 and it exhibits great advantage over H-103 when subjected to nitrobenzene at low concentrations. The adsorption capacity of CH-10 for nitrobenzene is 1.4 times as much as that of H-103 at the concentration of 100 mg/L. Kinetic study by film diffusion model and intra-particle diffusion model revealed that its distinctive mesoporous structure within pore diameters between 2 and 6 nm played significant role in the mass transfer at low concentrations, and these unique mesopores also resulted in better adsorption capacity, which was confirmed by adsorption thermodynamics study. Moreover, the CH series displayed a good affinity to a wide scope of nitroaromatics and exhibited excellent dynamic adsorption and desorption properties in fixed bed.

  10. Solidification of radioactive liquid wastes, Treatment options for spent resins and concentrates - 16405

    International Nuclear Information System (INIS)

    Roth, Andreas

    2009-01-01

    Ion exchange is one of the most common and effective treatment methods for liquid radioactive waste. However, spent ion exchange resins are considered to be problematic waste that in many cases require special approaches and pre-conditioning during its immobilization to meet the acceptance criteria for disposal. Because of the function that they fulfill, spent ion exchange resins often contain high concentrations of radioactivity and pose special handling and treatment problems. Another very common method of liquid radioactive waste treatment and water cleaning is the evaporation or diaphragm filtration. Both treatment options offer a high volume reduction of the total volume of liquids treated but generate concentrates which contain high concentrations of radioactivity. Both mentioned waste streams, spent resins as well as concentrates, resulting from first step liquid radioactive waste treatment systems have to be conditioned in a suitable manner to achieve stable waste products for final disposal. Spent resin and concentrate treatment often appear as a specific task in decommissioning projects, because in the past those waste streams typically had been stored in tanks for the lifetime of the plant and needs to be retrieved, conditioned and packed prior to dismantling activities. Additionally a large amount of contaminated liquids will be generated by utilizing decontamination processes and needs to be processed further on. Such treatment options need to achieve waste products acceptable for final disposal, because due to the closure of the site no interim storage can be envisaged. The most common method of treatment of such waste streams is the solidification in a solid matrix with additional inactive material like cement, polymer etc. In the past good results have been achieved and the high concentration of radioactivity can be reduced by adding the inactive material. On the other hand, under the environment of limited space for interim storage and the absence

  11. A convenient procedure for the solid-phase synthesis of hydroxamic acids on PEGA resins

    DEFF Research Database (Denmark)

    Nandurkar, Nitin Subhash; Petersen, Rico; Qvortrup, Katrine

    2011-01-01

    An efficient method for the solid-phase synthesis of hydroxamic acids is described. The method comprises the nucleophilic displacement of esters immobilized on PEGA resins with hydroxylamine/sodium hydroxide in isopropanol. The hydroxyaminolysis protocol is compatible with a broad range of PEGA...

  12. Influence of the Functionalization Degree of Acidic Ion-Exchange Resins on Ethyl Octyl Ether Formation

    Czech Academy of Sciences Publication Activity Database

    Guilera, J.; Hanková, Libuše; Jeřábek, Karel; Ramírez, E.; Tejero, J.

    2014-01-01

    Roč. 78, MAY (2014), s. 14-22 ISSN 1381-5148 Grant - others:SEURDO(ES) CTQ2010-16047 Institutional support: RVO:67985858 Keywords : acidic ion-exchange resin * sulfonation degree * ISEC Subject RIV: CC - Organic Chemistry Impact factor: 2.515, year: 2014

  13. Calcium isotope fractionation in liquid chromatography with benzo-18-crown-6 resin in aqueous hydrobromic acid medium

    International Nuclear Information System (INIS)

    Sato, Takuya; Oi, Takao

    2015-01-01

    Liquid chromatography operated in a breakthrough mode was employed to study calcium isotope fractionation in the aqueous hydrobromic acid medium. Highly porous silica beads, the inner pores of which were embedded with a benzo-18-crown-6 ether resin, were used as column packing material. Enrichment of heavier isotopes of calcium was observed in the frontal part of respective calcium chromatograms. The values of the isotope fractionation coefficient were on the order of 10 -3 . The observed isotope fractionation coefficient was dependent on the concentration of hydrobromic acid in the calcium feed solution; a higher HBr concentration resulted in a smaller fractionation coefficient value. The present calcium isotope effects were most probably mass-dependent, indicating that they mostly came from isotope effects based on molecular vibration. Molecular orbital calculations supported the present experimental results in a qualitative fashion. Chromatography operated in aqueous HBr media is a better system of Ca isotope separation than that operated in aqueous HCl media. (author)

  14. Eco-friendly Crosslinking Agent for Acid Functional Acrylic Resin

    Directory of Open Access Journals (Sweden)

    Archana Shah

    2009-01-01

    Full Text Available Oil from J. multifida was extracted and it was first converted into N,N-bis(2-hydroxyethyl Jatropha fatty amide (HEJFA. HEJFA has been synthesized by reaction between Jatropha oil and diethanol amine in presence of zinc oxide as a catalyst. The reaction is relatively rapid and proceeded to high yield at 200±5 OC. The resulting HEJFA was used to formulate thermosetting coating compositions. Films were cured at ambient (air drying and elevated (stove drying temperatures using N, N-bis(2-hydroxyethyl Jatropha fatty amide (HEJFA as eco-friendly crosslinking agent for acrylic resin. The coating performance of the various compositions was tested by measurement of scratch hardness, impact strength and chemical resistance. The results show better performance of the HEJFA based compositions compared to butylated melamine formaldehyde (MF based compositions.

  15. Biophysical study of resin acid effects on phospholipid membrane structure and properties

    DEFF Research Database (Denmark)

    Jagalski, Vivien; Barker, Robert; Topgaard, Daniel

    2016-01-01

    Hydrophobic resin acids (RAs) are synthesized by conifer trees as part of their defense mechanisms. One of the functions of RAs in plant defense is suggested to be the perturbation of the cellular membrane. However, there is a vast diversity of chemical structures within this class of molecules......, and there are no clear correlations to the molecular mechanisms behind the RA's toxicity. In this study we unravel the molecular interactions of the three closely related RAs dehydroabietic acid, neoabietic acid, and the synthetic analogue dichlorodehydroabietic acid with dipalmitoylphosphatidylcholine (DPPC) model...... are correlated with the physical chemical properties of the RA and their toxicity....

  16. Plasma Ascorbic Acid Concentration and some Haematological ...

    African Journals Online (AJOL)

    Aim: To determine the plasma ascorbic acid concentration, haematocrit, reticulocyte count and blood cell morphology in homozygous sickle cell disease in Enugu metropolis. Materals and Methods: Forty known sickle cell anaemia patients (HbSS) and ten non-sicklers (HbAA) were used as tests and controls respectively.

  17. Gastric Acid Secretion, Mucus Concentration and Ulceration ...

    African Journals Online (AJOL)

    This study was carried out to evaluate the effect of consumption (ingestion) of Cannabis sativa on the gastrointestinal tract using mucus concentration, acid secretion and ulceration in animal (rats) model as indices. Three groups of six (6) rats each were used. The control group were fed on rat chow only while another group ...

  18. Simultaneous separation and detection of actinides in acidic solutions using an extractive scintillating resin.

    Science.gov (United States)

    Roane, J E; DeVol, T A

    2002-11-01

    An extractive scintillating resin was evaluated for the simultaneous separation and detection of actinides in acidic solutions. The transuranic extractive scintillating (TRU-ES) resin is composed of an inert macroporous polystyrene core impregnated with organic fluors (diphenyloxazole and 1,4-bis-(4-methyl-5-phenyl-2-oxazolyl)benzene) and an extractant (octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide in tributyl phosphate). The TRU-ES resin was packed into FEP Teflon tubing to produce a flow cell (0.2-mL free column volume), which is placed into a scintillation detection system to obtain pulse height spectra and time series data during loading and elution of actinides onto/from the resin. The alpha-particle absolute detection efficiencies ranged from 77% to 96.5%, depending on the alpha energy and quench. In addition to the on-line analyses, off-line analyses of the effluent can be conducted using conventional detection methods. The TRU-ES resin was applied to the quantification of a mixed radionuclide solution and two actual waste samples. The on-line characterization of the mixed radionuclide solution was within 10% of the reported activities whereas the agreement with the waste samples was not as good due to sorption onto the sample container walls and the oxidation state of plutonium. Agreement between the on-line and off-line analyses was within 35% of one another for both waste samples.

  19. Inhibition of platelet aggregation by diterpene acids from Pinus massoniana resin.

    Science.gov (United States)

    Cheung, H T; Fu, S L; Smal, M A

    1994-01-01

    The acidic fraction of the resin of Pinus massoniana Lamb. from China was converted to the p-nitrophenyl esters, and the esters separated by chromatography. The separated p-nitrophenyl esters were individually hydrolysed by potassium hydroxide in acetone-water at room temperature to 8 diterpene acids of the pimarane and abietane groups: pimaric acid (8(14),15-pimaradien-18-oic acid) (1), levopimaric acid (8(14),12-abietadien-18-oic acid) (2), palustric acid (8,13-abietadien-18-oic acid) (3), neobietic acid (8(14),13(15)-abietadien-18-oic acid) (4), abietic acid (7,13-abietadien-18-oic acid) (5), dehydroabietic acid (8,11,13-abietatrien-18-oic acid) (6), 7-oxodehydroabietic acid (7-oxo-8,11,13-abietatrien-18-oic acid) (7) and 7 alpha-hydroxydehydroabietic acid (7 alpha-hydroxy-8,11,13-abietatrien-18-oic acid) (8). The structure (and stereochemistry) of the diterpene acids were substantiated by nuclear magnetic resonance spectroscopy (proton and carbon-13, one and two dimensional), by mass spectrometry (electron impact and methane chemical ionization) and by rotation measurements. The 8 diterpene acids were tested for their ability to inhibit the aggregation of washed rabbit platelets induced by platelet activating factor (PAF), adenosine diphosphate (ADP) and by calcium ionophore A23187. With platelet aggregation induced by the latter two agonists, activities comparable with or higher than linolenic acid were given by the first 4 acids. With aggregation induced by PAF, the first 3 acids show activity, but at a level significantly lower than that of linolenic acid. Levopimaric acid has the highest activity among the diterpene acids tested. It is proposed that this activity is related to the folded shape of the molecule.

  20. Study of plutonium IV elution from macromolecular anion exchange resin by 0.5 M nitric acid

    International Nuclear Information System (INIS)

    Nadkarni, M.N.; Mayankutty, P.C.; Pillai, N.S.; Shinde, S.S.

    1976-01-01

    Preliminary studies indicated that macroreticular resins possess more or less the same capacities and absorption characteristics for thorium, uranium and plutonium from nitric acid solutions as the conventional resins. Detailed studies were, then, conducted. It was found that Pu(IV) can be loaded on the macroreticular anion exchange resin, Amberlyst A-26 from 7.2 M nitric acid in much the same way as Dowex 1x4. It was also observed that the elution of Pu(IV) from Amberlyst A-26 by 0.5 M nitric acid is much more rapid and quantitative than from Dowex 1x4. (author)

  1. Inhibition of Streptococcus mutans biofilm formation on composite resins containing ursolic acid

    Science.gov (United States)

    Kim, Soohyeon; Song, Minju; Roh, Byoung-Duck; Park, Sung-Ho

    2013-01-01

    Objectives To evaluate the inhibitory effect of ursolic acid (UA)-containing composites on Streptococcus mutans (S. mutans) biofilm. Materials and Methods Composite resins with five different concentrations (0.04, 0.1, 0.2, 0.5, and 1.0 wt%) of UA (U6753, Sigma Aldrich) were prepared, and their flexural strengths were measured according to ISO 4049. To evaluate the effect of carbohydrate source on biofilm formation, either glucose or sucrose was used as a nutrient source, and to investigate the effect of saliva treatment, the specimen were treated with either unstimulated whole saliva or phosphate-buffered saline (PBS). For biofilm assay, composite disks were transferred to S. mutans suspension and incubated for 24 hr. Afterwards, the specimens were rinsed with PBS and sonicated. The colony forming units (CFU) of the disrupted biofilm cultures were enumerated. For growth inhibition test, the composites were placed on a polystyrene well cluster, and S. mutans suspension was inoculated. The optical density at 600 nm (OD600) was recorded by Infinite F200 pro apparatus (TECAN). One-way ANOVA and two-way ANOVA followed by Bonferroni correction were used for the data analyses. Results The flexural strength values did not show significant difference at any concentration (p > 0.01). In biofilm assay, the CFU score decreased as the concentration of UA increased. The influence of saliva pretreatment was conflicting. The sucrose groups exhibited higher CFU score than glucose group (p composite showed inhibitory effect on S. mutans biofilm formation and growth. PMID:23741708

  2. Separation of aliphatic carboxylic acids and benzenecarboxylic acids by ion-exclusion chromatography with various cation-exchange resin columns and sulfuric acid as eluent.

    Science.gov (United States)

    Ohta, Kazutoku; Ohashi, Masayoshi; Jin, Ji-Ye; Takeuchi, Toyohide; Fujimoto, Chuzo; Choi, Seong-Ho; Ryoo, Jae-Jeong; Lee, Kwang-Pill

    2003-05-16

    The application of various hydrophilic cation-exchange resins for high-performance liquid chromatography (sulfonated silica gel: TSKgel SP-2SW, carboxylated silica gel: TSKgel CM-2SW, sulfonated polymethacrylate resin: TSKgel SP-5PW, carboxylated polymethacrylate resins: TSKgel CM-5PW and TSKgel OA-Pak A) as stationary phases in ion-exclusion chromatography for C1-C7 aliphatic carboxylic acids (formic, acetic, propionic, butyric, isovaleric, valeric, isocaproic, caproic, 2-methylhexanoic and heptanoic acids) and benzenecarboxylic acids (pyromellitic, trimellitic, hemimellitic, o-phthalic, m-phthalic, p-phthalic, benzoic, salicylic acids and phenol) was carried out using diluted sulfuric acid as the eluent. Silica-based cation-exchange resins (TSKgel SP-2SW and TSKgel CM-2SW) were very suitable for the ion-exclusion chromatographic separation of these benzenecarboxylic acids. Excellent simultaneous separation of these benzenecarboxylic acids was achieved on a TSKgel SP-2SW column (150 x 6 mm I.D.) in 17 min using a 2.5 mM sulfuric acid at pH 2.4 as the eluent. Polymethacrylate-based cation-exchange resins (TSKgel SP-5PW, TSKgel CM-5PW and TSKgel OA-Pak A) acted as advanced stationary phases for the ion-exclusion chromatographic separation of these C1-C7 aliphatic carboxylic acids. Excellent simultaneous separation of these C1-C7 acids was achieved on a TSKgel CM-5PW column (150 x 6 mm I.D.) in 32 min using a 0.05 mM sulfuric acid at pH 4.0 as the eluent.

  3. Purification of gamma-amino butyric acid (GABA) from fermentation of defatted rice bran extract by using ion exchange resin

    Science.gov (United States)

    Tuan Nha, Vi; Phung, Le Thi Kim; Dat, Lai Quoc

    2017-09-01

    Rice bran is one of the significant byproducts of rice processing with 10 %w/w of constitution of whole rice grain. It is rich in nutrient compounds, including glutamic acid. Thus, it could be utilized for the fermentation with Lactobateria for synthesis of GABA, a valuable bioactive for antihypertensive effects. However, the concentration and purity of GABA in fermentation broth of defatted rice bran extract is low for production of GABA drug. This research focused on the purification of GABA from the fermentation broth of defatted rice bran extract by using cation exchange resin. The results indicate that, the adsorption isotherm of GABA by Purelite C100 showed the good agreement with Freundlich model, with high adsorption capacity. The effects of pH and concentration of NaCl in eluent on the elution were also investigated. The obtained results show that, at the operating conditions of elution as follows: pH 6.5, 0.8 M of NaCl in eluent, 0.43 of bed volume; concentration of GABA in accumulative eluent, the purity and recovery yield of GABA were 743.8 ppm, 44.0% and 84.2%, respectively. Results imply that, it is feasible to apply cation exchange resin for purification of GABA from fermentation broth of defatted rice bran extract.

  4. Evaluation of some anionic exchange resins as potential tablet ...

    African Journals Online (AJOL)

    The effect of resin concentration and compression force on the properties of tablets using the selected resin was investigated. In addition, the disintegrant efficacy of the selected resin in the tablet formulations containing either a basic drug, e.g., dextromethorphan hydrobromide (DMP), or an acidic drug, e.g., diclofenac ...

  5. [Plasma amino acid concentrations in aggressive dogs].

    Science.gov (United States)

    Juhr, Norbert-Christian; Brand, Ulrike; Riedel, Eberhard

    2005-01-01

    Following the hypothesis that metabolic screens may be useful tools in the diagnosis of canine aggression we have investigated the blood plasma amino acid levels of dogs which have been found aggressive (N = 10) against dogs or men in comparison to non-aggressive dogs (N = 10). In summary, the aggressive dogs showed elevated plasma concentrations of the neurophysiological active aromatic amino acids tryptophan (46/171 micromol/l, p urea-cycle in the conversion of ornithine (17/34 micromol/l, p < 0.01) to citrulline (64/47 micromol/l). Higher levels of branched chain amino acids, especially leucine (122/150 micromol/l, p < 0.01), mainly metabolized in muscles, and isoleucin (60/71 micromol/l, p < 0.05) show a high energy potential. The acidose-stimulator methionine (48/78 micromol/l, p < 0.01) proved elevated. The results show that the changed behavior in the aggressive dogs is also reflected in their free amino acid plasma concentrations, independent of the question whether these data are the cause or the result of the aggressivity.

  6. Bonding effectiveness of self-adhesive and conventional-type adhesive resin cements to CAD/CAM resin blocks. Part 2: Effect of ultrasonic and acid cleaning.

    Science.gov (United States)

    Kawaguchi, Asuka; Matsumoto, Mariko; Higashi, Mami; Miura, Jiro; Minamino, Takuya; Kabetani, Tomoshige; Takeshige, Fumio; Mine, Atsushi; Yatani, Hirofumi

    2016-01-01

    The present study assessed the effect of ultrasonic and acid cleaning on resin cement bonding to CAD/CAM resin blocks. One of two resin cements, PANAVIA V5 (PV5) or PANAVIA SA CEMENT HANDMIX (PSA), were bonded to one of 24 CAD/CAM blocks (KATANA AVENCIA BLOCK). Each cement group was divided into four subgroups: no cleaning (Ctl), ultrasonic cleaning (Uc), acid cleaning (Ac) and Uc+Ac. Micro-tensile bond strengths (µTBSs) were measured immediately and 1, 3, and 6 months after water storage. Block surfaces after each treatment were analyzed by scanning electron microscopy. Analysis of variance revealed a statistically significant effect for the parameters 'surface treatment' (p<0.001, F=40), 'resin cement' (p<0.001, F=696) and 'water aging' (p<0.001, F=71). The PV5 group exhibited higher µTBS values than the PSA group. Although cleaning after sandblasting was effective in removing residual alumina particles, it did not affect the long-term bonding durability with non-contaminated CAD/CAM resin blocks.

  7. Aminolysis of resin-bound N-nosylaziridine-2-carboxylic acids

    DEFF Research Database (Denmark)

    Olsen, Christian A; Christensen, Caspar; Nielsen, Birgitte

    2006-01-01

    [Structure: see text] Solid-phase synthesis is a rapidly developing area of organic chemistry, of particular importance for medicinal chemistry and chemical biology. Aziridines have previously only rarely been applied in solid-phase synthesis. In the present work, aminolysis of resin-bound, spring......-loaded N-nitrobenzenesulfonyl-activated aziridine-2-carboxylic acids has been optimized and employed in the synthesis of a number of open-chain and heterocyclic scaffolds, including enantiopure products....

  8. The effect of different fiber concentrations on the surface roughness of provisional crown and fixed partial denture resin.

    Science.gov (United States)

    Zortuk, Mustafa; Kılıc, Kerem; Uzun, Gulay; Ozturk, Ahmet; Kesim, Bulent

    2008-07-01

    The aim of this study was to investigate surface roughness in provisional crown acrylics, after polishing, reinforced with different concentrations of glass fibers. A total of 48 disk-shaped specimens were prepared using autopolymerizing acrylic resin. These specimens were divided into four groups according to the level of glass fiber added: Group A (no fiber), Group B (0.5%), Group C (1%) and Group D (2%). After polishing the specimens, an average surface roughness (Ra) value was calculated using a profilometer from four randomly selected points on the surface. A significant difference was determined among the surface roughness values of provisional crown resins to which different concentrations of fiber had been added (Pprovisional crown and fixed partial denture resin with glass fibers increases surface roughness.

  9. Screening Analyses of Pinosylvin Stilbenes, Resin Acids and Lignans in Norwegian Conifers

    Directory of Open Access Journals (Sweden)

    Anne Fiksdahl

    2006-01-01

    Full Text Available The content and distribution of stilbenes and resin acids in Scots pine (Pinus sylvestris and spruce (Picea abies, sampled in central Norway, have been examined. The contents of pinosylvin stilbenes in pine heartwood/living knots were 0.2-2/2-8 % (w/w. No stilbenes could be detected in spruce (Picea abies. The resin acid contents of pine sapwood/heartwood and knots were 1-4 and 5-10 % (w/w, respectively. Minor amounts of resin acids (< 0.2/< 0.04 %w/w were identified in spruce wood/knots. The lignan content in knots of Norwegian spruce was 6.5 % (w/w. Diastereomerically pure hydroxymatairesinol (HMR, 84 % of total lignans was readily isolated from this source since only minor quantities (2.6 % of total lignans of the allo-HMR diastereomer was detected. Insignificant amounts of lignans were present in the sapwood. Lignans could not be detected in the sapwood or knots of Norwegian sallow (Salix caprea, birch (Betula pendula or juniper (Juniperus communis.

  10. The application of macroporous resins in the separation of licorice flavonoids and glycyrrhizic acid.

    Science.gov (United States)

    Fu, Boqiang; Liu, Jie; Li, Huan; Li, Lei; Lee, Frank S C; Wang, Xiaoru

    2005-09-30

    Glycyrrhizic acid (GA) and licorice flavonoids (LF) are the two classes of bioactive components in licorice with known pharmacological effects. But long-term excessive intake of GA may cause sodium retention and hypertension. In this study, the performance and adsorption characteristics of four widely used macroporous resins for the separation of deglycyrrhizinated, flavonoids enriched licorice has been critically evaluated. The sorption and desorption properties of LF and GA on macroporous resins including XDA-1, LSA-10, D101 and LSA-20 have been compared. The adsorption capacity was found to depend strongly on the pH of the feed solution. XDA-1 offers much higher adsorption capacity for GA and LF than other resins, and its adsorption data fit the best to the Freundlich isotherm. XDA-1 also shows much higher adsorption affinity towards LF than that of GA based on calculated results from the measured adsorption isotherms. Dynamic adsorption and desorption experiments have been carried out on a XDA-1 resin packed column to obtain optimal parameters for separating GA and LF. An enriched LF extract (about 21.9% purity) free of GA, and an enriched GA extract with 66% purity can be separated from crude licorice extract in one run.

  11. Effect of humic acid on ciprofloxacin removal by magnetic multifunctional resins

    Science.gov (United States)

    Wang, Wei; Cheng, Jiade; Jin, Jing; Zhou, Qing; Ma, Yan; Zhao, Qingqing; Li, Aimin

    2016-07-01

    Background organic matter significantly influences the removal of emerging contaminants in natural water. In this work, the adsorption of ciprofloxacin (CPX) onto a series of magnetic multifunctional resins (GMA10-GMA90) in the presence and absence of humic acid (HA) was conducted to demonstrate the effect of HA. Both hydrophobic and ion exchange interactions contributed to CPX adsorption. Negative charge-assisted hydrogen bonds also participated in the adsorption process, resulting in the high adsorption amount of anionic CPX onto the negatively charged GMA30 under basic solutions. HA could impact CPX adsorption not only as a competitive adsorbate but also as an additional adsorbent. At pH 5.6, the additional adsorption sites provided by adsorbed HA molecules on the resins dominated and thus facilitated the adsorption process. While at pH 10, HA inhibited the adsorption of CPX by directly competing for ion exchange sites and coexisting with CPX in the solution. The ratio of the amount of CPX adsorbed by dissolved HA to that by the resin reached as high as 1.61 for GMA90. The adsorbed HA molecules onto the resins could provide additional adsorption sites for CPX as proven by the enhanced CPX adsorption in HA-preloading systems at pH 5.6.

  12. Oxidative degradation of low and intermediate level Radioactive organic wastes 2. Acid decomposition on spent Ion-Exchange resins

    International Nuclear Information System (INIS)

    Ghattas, N.K.; Eskander, S.B.

    1995-01-01

    The present work provides a simplified, effective and economic method for the chemical decomposition of radioactively contaminated solid organic waste, especially spent ion - exchange resins. The goal is to achieve volume reduction and to avoid technical problems encountered in processes used for similar purposes (incineration, pyrolysis). Factors efficiency and kinetics of the oxidation of the ion exchange resins in acid medium using hydrogen peroxide as oxidant, namely, duration of treatment and the acid to resin ratio were studied systematically on a laboratory scale. Moreover the percent composition of the off-gas evolved during the decomposition process was analysed. 3 figs., 5 tabs

  13. A new plastic scintillation resin for single-step separation, concentration and measurement of technetium-99

    Energy Technology Data Exchange (ETDEWEB)

    Barrera, J. [Department of Analytical Chemistry, Universitat de Barcelona, Martí i Franqués, 1-11, E-08028, Barcelona (Spain); Tarancón, A., E-mail: alex.tarancon@ub.edu [Department of Analytical Chemistry, Universitat de Barcelona, Martí i Franqués, 1-11, E-08028, Barcelona (Spain); Bagán, H. [Department of Pure and Applied Biochemistry, Lund University, Getingevägen 60, hus II, 22100 SE, Lund (Sweden); García, J.F. [Department of Analytical Chemistry, Universitat de Barcelona, Martí i Franqués, 1-11, E-08028, Barcelona (Spain)

    2016-09-14

    Technetium is a synthetic element with no stable isotopes, produced as waste in nuclear power plants and in cyclotrons used for nuclear medicine. The element has high mobility, in the form of TcO{sub 4}{sup −}; its determination is therefore important for environmental protection. Technetium is found in low concentrations and therefore common methods for its analysis include long treatments in several steps and require large amounts of reagents for its purification and preconcentration. Plastic scintillation resins (PSresin) are novel materials used to separate, preconcentrate and measure radionuclides in a single step. The objective of this study is to prepare and characterise a PSresin for the preconcentration and measurement of {sup 99}Tc. The study first evaluates the reproducibility of the production of PSresins between batches and over time; showing good reproducibility and storage stability. Next, we studied the effect of some common non-radioactive interferences, showing small influences on measurement, and radioactive interferences ({sup 36}Cl and {sup 238}U/{sup 234}U). {sup 36}Cl can be removed by a simple treatment with 0.5 M HCl and {sup 238}U/{sup 234}U can be removed from the column by cleaning with a mixture of 0.1 M HNO{sub 3} and 0.1 M HF. In the latter case, a slight change in the morphology of the PSresin caused an increase in detection efficiency. Finally, the PSresin was applied to the measurement of real spiked samples (sea water and urine) with deviations lower than 10% in all cases. - Highlights: • A plastic scintillation resin for selective analysis of {sup 99}Tc has been developed. • The method is valid for analysis of {sup 99}Tc in seawater and urine samples. • Presence of Cl{sup −}, NO{sub 3}{sup −}, SO{sub 4}{sup 2−}, {sup 36}Cl, U and Th not affect retention of {sup 99}Tc.

  14. Studies of transformation and particle-binding of resin acids during oxidative treatment of effluent from two New Zealand pulp mills.

    Science.gov (United States)

    Kanber, S A; Langdon, A G; Wilkins, A L

    2008-02-01

    Reactor studies of aerobic degradation of effluent from the first and last ponds of the treatment system of two New Zealand pulp and paper mills indicated that filterable BOD(5), resin acids and transformed resin acids, free and bound, degraded at similar rates. During oxidative treatment the resin acids of untreated effluent became increasingly bound to particulate material and a sediment high in abiet-13-enoic acid was formed.

  15. The Use of Commercial Non-Hazardous Air Pollutant Monomers to Optimize the Properties of Fatty Acid-Based Resins

    Science.gov (United States)

    2009-05-01

    It was found that cyclohexyl methacrylate (CHMA) was the most effective reactive diluent in replacing methacrylated lauric acid (MLau) because it...The reaction of glycidyl methacrylate and lauric acid to produce the MLau monomer... acid -based monomers to be used as the reactive diluent in VE resins (9, 10). Figure 1 depicts the synthetic route used to form methacrylated lauric

  16. Biogenic glutamic acid-based resin: Its synthesis and application in the removal of cobalt(II)

    Energy Technology Data Exchange (ETDEWEB)

    Jamiu, Zakariyah A.; Saleh, Tawfik A.; Ali, Shaikh A., E-mail: shaikh@kfupm.edu.sa

    2017-04-05

    Highlights: • A novel resin embedded with metal chelating glutamic acid was synthesized. • The biogenic amino acid residues imparted remarkable efficacy to remove Co(II). • The resin showed excellent ability to remove various metals from wastewater. - Abstract: Inexpensive biogenic glutamic acid has been utilized to synthesize a cross-linked dianionic polyelectrolyte (CDAP) containing metal chelating ligands. Cycloterpolymerization, using azoisobutyronitrile as an initiator, of N,N-diallylglutamic acid hydrochloride, sulfur dioxide and a cross-linker afforded a pH-responsive cross-linked polyzwitterionic acid (CPZA) which upon basification with NaOH was converted into CDAP. The new resin, characterized by a multitude of spectroscopic techniques as well as Scanning Electron Microscopy (SEM) and Brunauer–Emmett–Teller (BET) analyses, was evaluated for the removal of Co(II) as a model case under different conditions. The adsorption capacity of 137 mg g{sup −1} does indeed make the resin as one of the most effective sorbents in recent times. The resin leverages its cheap natural source and ease of regeneration in combination with its high and fast uptake capacities to offer a great promise for wastewater treatment. The resin has demonstrated remarkable efficiency in removing toxic metal ions including arsenic from a wastewater sample.

  17. Biogenic glutamic acid-based resin: Its synthesis and application in the removal of cobalt(II)

    International Nuclear Information System (INIS)

    Jamiu, Zakariyah A.; Saleh, Tawfik A.; Ali, Shaikh A.

    2017-01-01

    Highlights: • A novel resin embedded with metal chelating glutamic acid was synthesized. • The biogenic amino acid residues imparted remarkable efficacy to remove Co(II). • The resin showed excellent ability to remove various metals from wastewater. - Abstract: Inexpensive biogenic glutamic acid has been utilized to synthesize a cross-linked dianionic polyelectrolyte (CDAP) containing metal chelating ligands. Cycloterpolymerization, using azoisobutyronitrile as an initiator, of N,N-diallylglutamic acid hydrochloride, sulfur dioxide and a cross-linker afforded a pH-responsive cross-linked polyzwitterionic acid (CPZA) which upon basification with NaOH was converted into CDAP. The new resin, characterized by a multitude of spectroscopic techniques as well as Scanning Electron Microscopy (SEM) and Brunauer–Emmett–Teller (BET) analyses, was evaluated for the removal of Co(II) as a model case under different conditions. The adsorption capacity of 137 mg g −1 does indeed make the resin as one of the most effective sorbents in recent times. The resin leverages its cheap natural source and ease of regeneration in combination with its high and fast uptake capacities to offer a great promise for wastewater treatment. The resin has demonstrated remarkable efficiency in removing toxic metal ions including arsenic from a wastewater sample.

  18. Esterification of palm fatty acid distillate with epychlorohydrin using cation exchange resin catalyst

    Science.gov (United States)

    Budhijanto, Budhijanto; Subagyo, Albertus F. P. H.

    2017-05-01

    Palm Fatty Acid Distillate (PFAD) is one of the wastes from the conversion of crude palm oil (CPO) into cooking oil. The PFAD is currently only utilized as the raw material for low grade soap and biofuel. To improve the economic value of PFAD, it was converted into monoglyceride by esterification process. Furthermore, the monoglyceride could be polymerized to form alkyd resin, which is a commodity of increasing importance. This study aimed to propose a kinetics model for esterification of PFAD with epichlorohydrin using cation exchange resin catalyst. The reaction was the first step from a series of reactions to produce the monoglyceride. In this study, the reaction between PFAD and epichlorohydirne was run in a stirred batch reactor. The stirrer was operated at a constant speed of 400 RPM. The reaction was carried out for 180 minutes on varied temperatures of 60°C, 70°C, 80°C, dan 90°C. Cation exchange resin was applied as solid catalysts. Analysis was conducted periodically by measuring the acid number of the samples, which was further used to calculate PFAD conversion. The data were used to determine the rate constants and the equilibrium constants of the kinetics model. The kinetics constants implied that the reaction was reversible and controlled by the intrinsic surface reaction. Despite the complication of the heterogeneous nature of the reaction, the kinetics data well fitted the elementary rate law. The effect of temperature on the equilibrium constants indicated that the reaction is exothermic.

  19. Biodiesel production from acid oils and ethanol using a solid basic resin as catalyst

    International Nuclear Information System (INIS)

    Marchetti, J.M.; Errazu, A.F.

    2010-01-01

    In the search of an alternative fuel to substitute diesel fuel, biodiesel appears as one of the most promising sources of energy for diesel engines because of its environmental advantages and also due to the evolution of the petroleum market. Refined oil is the conventional raw material for the production of this biofuel; however, its major disadvantage is the high cost of its production. Therefore, frying oils, waste oils, crude oils and/or acid oils are being tested as alternative raw materials; nevertheless, there will be some problems if a homogeneous basic catalyst (NaOH) is employed due to the high amount of free fatty acid present in the raw oil. In this work, the transesterification reaction of acid oil using solid resin, Dowex monosphere 550 A, was studied as an alternative process. Ethanol was employed to have a natural and sustainable final product. The reaction temperature's effects, the initial amount of free fatty acid, the molar ratio of alcohol/oil and the type of catalyst (homogeneous or heterogeneous) over the main reaction are analyzed and their effects compared. The results obtained show that the solid resin is an alternative catalyst to be used to produce fatty acid ethyl esters (FAEEs) by a transesterification reaction with a final conversion over 90%. On the other hand, the time required to achieve this conversion is bigger than the one required using conventional technology which employs a homogeneous basic catalyst. This reaction time needs to be optimized. (author)

  20. Recovery of tretrachloroaurate through ion exchange with Dowex 11 resin

    International Nuclear Information System (INIS)

    Alguacil, F.J.

    1998-01-01

    The recovery of the tretrachloroaurate complex by the anionic ion exchange resin Dowex 11 has been studied. The kinetics of gold adsorption were dependent of both gold and resin concentrations and temperature. The adsorption isotherm can be described by the expression Q=kC''n. The loaded resin could be eluted by an acidic thiourea solution at 20 degree centigree. After several adsorption-elution cycles there is not any apparent loss in the adsorption properties of the resin. (Author) 6 refs

  1. Synthesis and Characterization of Dimmer-Acid-Based Nonisocyanate Polyurethane and Epoxy Resin Composite

    Directory of Open Access Journals (Sweden)

    Xin He

    2017-11-01

    Full Text Available In this study, dimmer-acid-based hybrid nonisocyanate polyurethanes (HNIPUs were synthesized by the one-step method without catalyst. Three polyamines and two epoxy resins were selected as raw materials for HNIPU, and cyclic carbonate was synthesized based on our previous work. All of the products were characterized by Fourier transform infrared spectroscopy (FTIR, differential scanning calorimetry (DSC, thermogravimetric analysis (TGA and dynamic mechanical analysis (DMA. Then, HNIPU coatings were prepared and determined by swelling, water absorption, and water contact angle. The results showed that the HNIPU-4551 have the best mechanical and thermal properties because of its high crosslinking density. Among the different amines, it was confirmed that tetraethylenepentamine was the best amine curing agent for HNIPU coating. Meanwhile, the epoxy resin with a higher epoxy value would also form a higher crosslinking density. Those coatings showed an excellent impact strength, adhesion, flexibility, pencil hardness, hydrophilic, and appropriate crosslinking density.

  2. Adsorption and removal of clofibric acid and diclofenac from water with MIEX resin.

    Science.gov (United States)

    Lu, Xian; Shao, Yisheng; Gao, Naiyun; Chen, Juxiang; Zhang, Yansen; Wang, Qiongfang; Lu, Yuqi

    2016-10-01

    This study demonstrates the use of MIEX resin as an efficient adsorbent for the removal of clofibric acid (CA) and diclofenac (DCF). The adsorption performance of CA and DCF are investigated by a batch mode in single-component or bi-component adsorption system. Various factors influencing the adsorption of CA and DCF, including initial concentration, contact time, adsorbent dosage, initial solution pH, agitation speed, natural organic matter and coexistent anions are studied. The Langmuir model can well describe CA adsorption in single-component system, while the Freundlich model gives better fitting in bi-component system. The DCF adsorption can be well fitted by the Freundlich model in both systems. Thermodynamic analyses show that the adsorption of CA and DCF is an endothermic (ΔH(o) > 0), entropy driven (ΔS(o) > 0) process and more randomness exists in the DCF adsorption process. The values of Gibbs free energy (ΔG(o)  0) for CA adsorption. The kinetic data suggest the adsorption of CA and DCF follow the pseudo-first-order model in both systems and the intra-particle is not the unique rate-limiting step. The adsorption process is controlled simultaneously by external mass transfer and surface diffusion according to the surface diffusion modified Biot number (Bis) ranging from 1.06 to 26.15. Moreover, the possible removal mechanism for CA and DCF is respectively proposed based on the ion exchange stoichiometry. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Selective sorption of ruthenium from acidic medium by Amberlite XAD 7 resin impregnated with iodide salt of N,N'-diisobutyl(α-Trialkylammonium)-acetamide

    International Nuclear Information System (INIS)

    Sharma, Shikha; Ghosh, Sunil K.; Sharma, J.N.

    2015-01-01

    This work investigates the removal of ruthenium (III) from aqueous nitric acid solutions using solvent impregnated resin (SIR). The SIR has been made by impregnating Amberlite XAD-7 with iodide salt of N,N'-diisobutyl(α-trialkylammonium)acetamide as the extractant and methanol as the solvent by a wet impregnation technique. This solvent has already been successfully investigated by us for selective extraction of ruthenium (III) from nitric acid solution by solvent extraction technique. Maximum loading of ammonium acetamide on Amberlite XAD was found to be in the ratio of 1:2. Loaded resin was characterized by IR and SEM analyses. The effect of metal ion concentration on the sorption of ruthenium (III) ions has been investigated to quantify the sorption capacity of resin for Ru. Maximum loading of ruthenium was found to be 14 mg/g of resin. Maximum K d obtained was 754. Ruthenium was successfully stripped from SIR using sodium hydroxide solution in a single contact. (author)

  4. Non-destructive evaluation by terahertz spectroscopy for penetration of acid solutions into epoxy resin

    Directory of Open Access Journals (Sweden)

    M. Kusano

    2016-11-01

    Full Text Available Epoxy resins are used as high-performance thermosetting linings to protect substrates under corrosive environments. However, in a severe corrosive chemical solution, such protective layers may degrade with long time due to penetrations of solvent and solute molecules into resin network. In this regard, the terahertz time-domain spectroscopy (THz-TDS is a promising tool for non-destructive evaluation of the penetrant amounts due to high transparency of such plastic materials and high sensitivity to the molecular vibrations in terahertz spectral range. In this work, the complex refractive indexes n and κ of epoxy specimens were measured after immersion into sulfuric acid solutions and compared with penetrated mass fractions of water and acid ions. It was found that n and κ depended linearly with water and sulfuric acid mass fraction in specimens, and κ of sulfuric acid immersed specimens was lager at higher frequency. While the calculated Δκ agreed well with THz-TDS measurement by THz-TDS, the calculated Δn was higher than the measurement. The difference may be attributed to the water and sulfuric states in the specimen.

  5. Adsorption of beta-naphthalenesulfonic acid/sulfuric acid from their solution by weakly basic resin: equilibrium.

    Science.gov (United States)

    Li, Chang-Hai; Si, Peng-Fei

    2005-01-01

    Experiments for single and bisolute competitive adsorption were carried out to investigate the adsorption behavior of beta-naphthalenesulfonic acid (NSA) and sulfuric acid (H2SO4) from their solution at 25 degrees C onto weakly basic resin D301R. Adsorption affinity of sulfuric acid on D301R was found to be much higher than that of NSA. The data of single-solute adsorption were fitted to the Langmuir model and the Freundlich adsorption model. The ideal adsorbed solution theory (IAST) coupled with the single-solute adsorption models were used to predict the bisolute competitive adsorption equilibria. The IAST coupled with the Langmuir and the Freundlich model for sulfuric acid and NSA, respectively, yields the favorable representation of the bisolute competitive adsorption behavior.

  6. Evaluation and improvement of gamma-ray stability of chelating resins containing oxy-acid groups of phosphorus

    International Nuclear Information System (INIS)

    Jyo, Akinori; Yamabe, Kazunori; Shuto, Taketomi

    1998-01-01

    Chelating resins containing oxy-acid groups of phosphorus, such as phosphonic and phosphoric acid groups have been studied from the point of view of solvent extraction processes for the separation of nuclear fuel elements as well as of fission product ones. The present work was planned to evaluate the effect of gamma-ray on properties of the resins and to obtain directional information for design of the resins having high stability to gamma-ray. It was clarified that gamma-ray stability of the resins is not high; tolerance limit is ca. 2.3x10 3 C/kg. The present work also clarified that polymers crosslinked with divinylbenzene have much higher gamma-ray stability than ones crosslinked with dimetacrylate esters of oligo (ethylene glycol)s. (J.P.N.)

  7. Exposure of Atlantic salmon parr (Salmo salar) to a combination of resin acids and a water soluble fraction of diesel fuel oil: A model to investigate the chemical causes of pigmented salmon syndrome

    Energy Technology Data Exchange (ETDEWEB)

    Croce, B. [Scottish Office Agriculture, Environment, and Fisheries Dept., Aberdeen (United Kingdom). Marine Lab.]|[Scottish Environmental Protection Agency, Aberdeen (United Kingdom). North East River Purification Board; Stagg, R.M. [Scottish Office Agriculture, Environment, and Fisheries Dept., Aberdeen (United Kingdom). Marine Lab.

    1997-09-01

    Pigmented salmon syndrome is a pollutant-induced hemolytic anemia and hyperbilirubinemia. As part of an investigation of this condition, S2 Atlantic salmon parr (Salmo salar) were exposed to a diesel fuel oil, water soluble fraction (WSF) in combination with a mixture of three resin acids (isopimaric, dehydroabietic, and abietic acids) in a continuous-flow freshwater system. The total nominal concentrations of resin acids in the exposure tanks were 10, 50, and 100 {micro}g/L; the diesel WSF was generated in situ and provided a mean hydrocarbon concentration of 2.0 {+-} 0.1 mg/L (n = 12) during the 9-d exposure period. Exposure to the diesel WSF alone depressed liver bilirubin UDP-glucuronosyl transferase (UDPGT) activity and induced phenol UDPGT activity. Exposure to the diesel WSF in the absence or presence of resin acids induced liver cytochrome P4501A and increased the concentrations in the plasma of the enzymes lactate dehydrogenase, alkaline phosphatase, and glutamic oxaloacetic transaminase. The combined exposure to diesel WSF with either 50 or 100 {micro}g/L total resin acid caused significant elevations in the concentrations of bilirubin in the plasma and many of these fish had yellow pigmentation on the ventral surface and around the gill arches. The results demonstrate that exposure to combinations of two groups of contaminants can result in the manifestation of toxic effects not apparent from exposure to either of these chemicals in isolation.

  8. Application of 10% Ascorbic Acid Improves Resin Shear Bond Stregth in Bleached Dentin

    Directory of Open Access Journals (Sweden)

    Kamizar Kamizar

    2014-10-01

    Full Text Available Normal 0 false false false IN X-NONE X-NONE MicrosoftInternetExplorer4 Restoration of the teeth immediately after bleaching with H2O2 35% is contraindicated due to the remnants of free radical that will stay inside dentin for 2-3 weeks which will compromise the adhesiveness of composite resin. Objective: The aim of this study was to evaluate the influence of 10% ascorbic acid on shear bond strength of composite placed on bleached dentin. Methods:Twenty seven samples were divided equally into three groups. Group 1: dentin was etched with 35% phosphoric acid; Group 2: dentin was bleached with 35% H2O2 followed by etching with 35% phosphoric acid; Group 3: dentin was bleached with 35% H2O2, followed by application of 10% ascorbic acid and etched with 35% phosphoric acid. All samples were then stored at 370C for 24 hours. The Universal Testing Machine was used to measure shear bond strength and the results were analyzed with Kruskal Wallis and Mann Whitney test. Results: After nine independent experiments, 10% ascorbic acid application on bleached dentin resulted in highest increased in bond stregth (56.04±11.06MPa compared to Group 2 (29.09±7.63MPa and Group 1 (25.55±2.22MPa and the difference was statistically significant (p<0.05. Conclusion: Application of 10% ascorbic acid to the bleached dentin improved the shear bond strength of resin composite.

  9. Uranium adsorption from the sulphuric acid leach liquor containing more chlorides with cation-exchange resin SL-406

    International Nuclear Information System (INIS)

    Hu Jun; Wang Zhaoguo; Chi Renqing; Niu Xuejun

    1994-01-01

    The feasibility of uranium adsorption was studied from the sulphuric acid leach liquor of a uranium ore containing more chlorides with cation-exchange resin SL-406. The influence of some factors on uranium adsorption was investigated. It was shown that the resin possesses better selectivity, stability and higher capacity. It can be effectively used to recovery uranium from leach liquors of uranium ores containing more chlorides

  10. Adsorption behavior of benzenesulfonic acid by novel weakly basic anion exchange resins.

    Science.gov (United States)

    Sun, Yue; Zuo, Peng; Luo, Junfen; Singh, Rajendra Prasad

    2017-04-01

    Two novel weakly basic anion exchange resins (SZ-1 and SZ-2) were prepared via the reaction of macroporous chloromethylated polystyrene-divinylbenzene (Cl-PS-DVB) beads with dicyclohexylamine and piperidine, respectively. The physicochemical structures of the resulting resins were characterized using Fourier Transform Infrared Spectroscopy and pore size distribution analysis. The adsorption behavior of SZ-1 and SZ-2 for benzenesulfonic acid (BA) was evaluated, and the common commercial weakly basic anion exchanger D301 was also employed for comparison purpose. Adsorption isotherms and influence of solution pH, temperature and coexisting competitive inorganic salts (Na 2 SO 4 and NaCl) on adsorption behavior were investigated and the optimum desorption agent was obtained. Adsorption isotherms of BA were found to be well represented by the Langmuir model. Thermodynamic parameters involving ΔH, ΔG and ΔS were also calculated and the results indicate that adsorption is an exothermic and spontaneous process. Enhanced selectivity of BA sorption over sulfate on the two novel resins was observed by comparison with the commercial anion exchanger D301. The fact that the tested resins loaded with BA can be efficiently regenerated by NaCl solution indicates the reversible sorption process. From a mechanistic viewpoint, this observation clearly suggests that electrostatic interaction is the predominant adsorption mechanism. Furthermore, results of column tests show that SZ-1 possesses a better adsorption property than D301, which reinforces the feasibility of SZ-1 for potential industrial application. Copyright © 2016. Published by Elsevier B.V.

  11. HTGR fuel development: loading of uranium on carboxylic acid cation-exchange resins using solvent extraction of nitrate

    International Nuclear Information System (INIS)

    Haas, P.A.

    1975-09-01

    The reference fuel kernel for recycle of 233 U to HTGR's (High-Temperature Gas-Cooled Reactors) is prepared by loading carboxylic acid cation-exchange resins with uranium and carbonizing at controlled conditions. The purified 233 UO 2 (NO 3 ) 2 solution from a fuel reprocessing plant contains excess HNO 3 (NO 3 - /U ratio of approximately 2.2). The reference flowsheet for a 233 U recycle fuel facility at Oak Ridge uses solvent extraction of nitrate by a 0.3 M secondary amine in a hydrocarbon diluent to prepare acid-deficient uranyl nitrate. This nitrate extraction, along with resin loading and amine regeneration steps, was demonstrated in 14 runs. No significant operating difficulties were encountered. The process is controlled via in-line pH measurements for the acid-deficient uranyl nitrate solutions. Information was developed on pH values for uranyl nitrate solution vs NO 3 - /U mole ratios, resin loading kinetics, resin drying requirements, and other resin loading process parameters. Calculations made to estimate the capacities of equipment that is geometrically safe with respect to control of nuclear criticality indicate 100 kg/day or more of uranium for single nitrate extraction lines with one continuous resin loading contactor or four batch loading contactors. (auth)

  12. Fracture Toughness Evaluation of Hybrid and Nano-hybrid Resin Composites after Ageing under Acidic Environment

    Directory of Open Access Journals (Sweden)

    Ferooz M

    2015-03-01

    Full Text Available Statement of Problem: Tooth-coloured restorative materials are brittle with the major shortcomings of sensitivity to flaws and defects. Although various mechanical properties of resin composites have been studied, no fracture toughness test data for nano-hybrid composites under acidic condition for a long period of time has been published. Objectives: To compare the fracture toughness (KIc of two types of resin composites under tensile loading and to assess the effect of distilled water and lactic acid on the resistance of the restoratives to fracture after three months of immersion. Materials and Methods: Four resin composites were used: three nanohybrids [EsteliteSigma Quick (Kuraray, Luna (SDI, Paradigm (3M/ESPE] and one hybrid, Rok (SDI. The specimens were prepared using a custom-made polytetrafluorethylene split mould, stored in distilled water (pH 6.8 or 0.01mol/L lactic acid (pH 4 and conditioned at 37°C for 24 hours, 1 or 3 months. They were loaded under tensile stress using a universal testing machine; the maximum load (N to the specimen failure was recorded and the fracture toughness (KIc was calculated. Data were analysed by ANOVA and Tukey’s test using SPSS, version 18. Results: The results of two-way ANOVA did not show a significant combined effect of material, time, and storage medium on fracture toughness (p= 0.056. However, there was a strong interaction between materials and time (p=0.001 when the storage medium were ignored. After 24 h of immersion in distilled water, Paradigm revealed the highest KIc values followed by Rok, Luna and Estelite. Immersion in either distilled water or lactic acid significantly decreased the fracture toughness of almost all materials as time interval increased. Conclusions: Paradigm showed the highest fracture toughness followed by Rok, Luna and Estelite respectively. As time increased, KIc significantly decreased for almost all resin composites except for Luna which showed a slight decrease

  13. Resin bead-thermal ionization mass spectrometry for determination of plutonium concentration in irradiated fuel dissolver solution

    International Nuclear Information System (INIS)

    Paul, Sumana; Shah, R.V.; Aggarwal, S.K.; Pandey, A.K.

    2015-01-01

    Determination of isotopic composition (IC) and concentration of plutonium (Pu) is necessary at various stages of nuclear fuel cycle which involves analysis of complex matrices like dissolver solution of irradiated fuel, nuclear waste stream etc. Mass spectrometry, e.g. thermal ionization mass spectrometry (TIMS) and inductively coupled plasma mass spectrometry (ICP-MS) are commonly used for determination of IC and concentration of plutonium. However, to circumvent matrix interferences, efficient separation as well as preconcentration of Pu is required prior to mass spectrometric analysis. Purification steps employing ion-exchange resins are widely used for the separation of Pu from dissolver solution or from mixture of other actinides e.g. U, Am. However, an alternative way is to selectively preconcentrate Pu on a resin bead, followed by direct loading of the bead on the filament of thermal ionization mass spectrometer

  14. Biobased carbon content of resin extracted from polyethylene composite by carbon-14 concentration measurements using accelerator mass spectrometry.

    Science.gov (United States)

    Taguchi, Kazuhiro; Kunioka, Masao; Funabashi, Masahiro; Ninomiya, Fumi

    2014-01-01

    An estimation procedure for biobased carbon content of polyethylene composite was studied using carbon-14 ((14)C) concentration ratios as measured by accelerated mass spectrometry (AMS). Prior to the measurement, additives and fillers in composites should be removed because they often contain a large amount of biobased carbon and may shift the estimation. Samples of resin with purity suitable for measurement were isolated from composites with a Soxhlet extractor using heated cyclohexanone. After cooling of extraction solutions, the resin was recovered as a fine semi-crystalline precipitate, which was easily filtered. Recovery rates were almost identical (99%), even for low-density polyethylene and linear low-density polyethylene, which may have lower crystallinity. This procedure could provide a suitable approach for estimation of biobased carbon content by AMS on the basis of the standard ASTM D 6866. The biobased carbon content for resin extracted from polyethylene composites allow for the calculation of biosynthetic polymer content, which is an indicator of mass percentage of the biobased plastic resin in the composite.

  15. The Effect of Different Fiber Concentrations on the Surface Roughness of Provisional Crown and Fixed Partial Denture Resin

    OpenAIRE

    Zortuk, Mustafa; K?l?c, Kerem; Uzun, Gulay; Ozturk, Ahmet; Kesim, Bulent

    2008-01-01

    Objectives The aim of this study was to investigate surface roughness in provisional crown acrylics, after polishing, reinforced with different concentrations of glass fibers. Methods A total of 48 disk-shaped specimens were prepared using autopolymerizing acrylic resin. These specimens were divided into four groups according to the level of glass fiber added: Group A (no fiber), Group B (0.5%), Group C (1%) and Group D (2%). After polishing the specimens, an average surface roughness (Ra) va...

  16. A new plastic scintillation resin for single-step separation, concentration and measurement of technetium-99.

    Science.gov (United States)

    Barrera, J; Tarancón, A; Bagán, H; García, J F

    2016-09-14

    Technetium is a synthetic element with no stable isotopes, produced as waste in nuclear power plants and in cyclotrons used for nuclear medicine. The element has high mobility, in the form of TcO4(-); its determination is therefore important for environmental protection. Technetium is found in low concentrations and therefore common methods for its analysis include long treatments in several steps and require large amounts of reagents for its purification and preconcentration. Plastic scintillation resins (PSresin) are novel materials used to separate, preconcentrate and measure radionuclides in a single step. The objective of this study is to prepare and characterise a PSresin for the preconcentration and measurement of (99)Tc. The study first evaluates the reproducibility of the production of PSresins between batches and over time; showing good reproducibility and storage stability. Next, we studied the effect of some common non-radioactive interferences, showing small influences on measurement, and radioactive interferences ((36)Cl and (238)U/(234)U). (36)Cl can be removed by a simple treatment with 0.5 M HCl and (238)U/(234)U can be removed from the column by cleaning with a mixture of 0.1 M HNO3 and 0.1 M HF. In the latter case, a slight change in the morphology of the PSresin caused an increase in detection efficiency. Finally, the PSresin was applied to the measurement of real spiked samples (sea water and urine) with deviations lower than 10% in all cases. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Affinity purification of the voltage-sensitive sodium channel from electroplax with resins selective for sialic acid

    Energy Technology Data Exchange (ETDEWEB)

    James, W.M.; Emerick, M.C.; Agnew, W.S. (Yale Univ. School of medicine, New Haven, CT (USA))

    1989-07-11

    The voltage-sensitive sodium channel present in the eel (Electrophorus electricus) has an unusually high content of sialic acid, including {alpha}-(2{yields}8)-linked polysialic acid, not found in other electroplax membrane glycopeptides. Lectins from Limax flavus (LFA) and wheat germ (WGA) proved the most effective of 11 lectin resins tried. The most selective resin was prepared from IgM antibodies against Neisseria meningitidis {alpha}-(2{yields}8)-polysialic acid which were affinity purified and coupled to Sepharose 4B. The sodium channel was found to bind to WGA, LFA, and IgM resins and was readily eluted with the appropriate soluble carbohydrates. Experiments with LFA and IgM resins demonstrated binding and unbinding rates and displacement kinetics, which suggest highly specific binding at multiple sites on the sodium channel protein. In preparative-scale purification of protein previously fractionated by anion-exchange chromatography, without stabilizing TTX, high yields were reproducibly obtained. Further, when detergent extracts were prepared from electroplax membranes fractionated by low-speed sedimentation, a single step over the IgM resin provided a 70-fold purification, yielding specific activities of 3,200 pmol of ({sup 3}H)TTX-binding sites/mg of protein and a single polypeptide of {approximately}285,000 Da on SDS-acrylamide gels. No small peptides were observed after this 5-h isolation. The authors describe a cation-dependent stabilization with millimolar levels of monovalent and micromolar levels of divalent species.

  18. Influence of ozone and paracetic acid disinfection on adhesion of resilient liners to acrylic resin

    Science.gov (United States)

    2016-01-01

    PURPOSE The aim of this study was to evaluate the effect of paracetic acid (PAA) and ozone disinfection on the tensile bond strength (TBS) of silicone-based resilient liners to acrylic resins. MATERIALS AND METHODS One hundred and twenty dumbbell shaped heat-polymerized acrylic resins were prepared. From the mid segment of the specimens, 3 mm of acrylic were grinded off and separated parts were reattached by resilient liners. The specimens were divided into 2 control (control1, control7) and 4 test groups of PAA and ozone disinfection (PAA1, PAA7, ozone1 and ozone7; n=10). While control groups were immersed in distilled water for 10 min (control1) and 7 days (control7), test groups were subjected to PAA (16 g/L) or ozone rich water (4 mg/L) for 1 cycle (10 min for PAA and 60 min for ozone) per day for 7 days prior to tensile tests. Measurements of the TBS were analyzed using 3-way ANOVA and Tukey's HSD test. RESULTS Adhesive strength of Mollosil decreased significantly by application of ozone disinfection. PAA disinfection had no negative effect on the TBS values of Mollosil and Molloplast B to acrylic resin. Single application of ozone disinfection did not have any negative effect on TBS values of Molloplast B, but prolonged exposure to ozone decreased its adhesive strength. CONCLUSION The adhesion of resilient liners to acrylic was not adversely affected by PAA disinfection. Immersion in ozonated water significantly decreased TBS of Mollosil. Prolonged exposure to ozone negatively affects adhesion of Molloplast B to denture base materials. PMID:27555898

  19. Stability of two resin combinations used as sealants against toothbrush abrasion and acid challenge in vitro.

    Science.gov (United States)

    Yetkiner, Enver; Wegehaupt, Florian Just; Attin, Rengin; Wiegand, Annette; Attin, Thomas

    2014-11-01

    To test the stability of two conventional adhesives when combined with a low-viscosity caries infiltrant used for sealing sound enamel against toothbrush abrasion and acid challenge in vitro. Bovine enamel discs (Ø = 3 mm) randomly assigned to three groups (n = 10/group) were etched with 37% phosphoric acid for 30 s and treated with resins of different monomer contents forming three test groups: (1) Untreated specimens (Control); (2) Infiltrant (Icon, DMG) + conventional enamel bonding adhesive (Heliobond, Ivoclar Vivadent); and (3) Infiltrant + conventional orthodontic adhesive (Transbond XT Primer, 3M Unitek). All specimens were immersed in hydrochloric acid (pH 2.6) for up to 9 days, during which they were exposed to 1825 toothbrush-strokes per day. Calcium dissolution was assessed using Arsenazo III method at 24-h intervals. Data were analyzed by Kruskal-Wallis and Wilcoxon signed ranks tests. Cumulative calcium dissolution for the untreated specimens (39.75 ± 7.32 μmol/ml) exceeded the sealed groups (Icon + Heliobond: 23.44 ± 7.03 μmol/ml; Icon + Transbond XT Primer: 22.17 ± 5.34 μmol/ml). Untreated specimens presented a relatively constant calcium dissolution rate throughout the experimental period, whereas the sealed groups presented a gradual increase indicating weakening of the seal by toothbrush abrasion. Both sealed groups presented significantly lower daily calcium dissolution at all time points compared to the control, except for Group 2 on the last measurement day. Low-viscosity caries infiltrant application on sound enamel prior to conventional resin application provided a protective effect against enamel demineralization, but this effect was not stable when challenged mechanically by toothbrush abrasion.

  20. Ion-exchange Resin Catalyzed Esterification of Lactic Acid with Isopropanol: a Kinetic Study

    Directory of Open Access Journals (Sweden)

    Amrit P. Toor

    2011-05-01

    Full Text Available The kinetic behavior of esterification of lactic acid with isopropanol over an acidic cation exchange resin, Amberlyst 15, was studied under isothermal condition. Isopropyl lactate synthesized in this reaction is an important pharmaceutical intermediate. The experiments were carried out in a stirred batch reactor in the temperature range of 323.15 to 353.15 K. The effect of various parameters such as temperature, molar ratio and catalyst loading was studied. Variation in parameters on rate of reaction demonstrated that the reaction was intrinsically controlled. Kinetic modeling was performed using Eley-Rideal model which acceptably fits the experimental data. The activation energy was found to be 22.007 kJ/mol and frequency factor was 0.036809 l2 g-1 mol-1 min-1 for forward reaction. The value of entropy for the forward reaction was found to be 182.317 J K-1 mol-1 . © 2011 BCREC UNDIP. All rights reserved(Received: 19th January 2011, Revised: 16th March 2011; Accepted: 16th March 2011[How to Cite: A.P. Toor, M. Sharma, S. Thakur, and R. K. Wanchoo. (2011. Ion-exchange Resin Catalyzed Esterification of Lactic Acid with Isopropanol: a Kinetic Study. Bulletin of Chemical Reaction Engineering and Catalysis, 6(1: 39-45. doi:10.9767/bcrec.6.1.791.39-45][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.6.1.791.39-45 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/791 ] | View in  

  1. Impact of pH and application time of meta-phosphoric acid on resin-enamel and resin-dentin bonding.

    Science.gov (United States)

    Cardenas, A F M; Siqueira, F S F; Bandeca, M C; Costa, S O; Lemos, M V S; Feitora, V P; Reis, A; Loguercio, A D; Gomes, J C

    2018-02-01

    To evaluate the immediate microshear resin-enamel bond strength (μSBS) and the immediate and 6-month microtensile bond strength (μTBS) and nanoleakage (NL) of the adhesive interface performed by different pHs of 40% meta-phosphoric acid (MPA) were compared with conventional 37% ortho-phosphoric acid (OPA) under different application times. Additionally, the enamel etching patterns were evaluated and the chemical/morphological changes induced by these differents groups were evaluated. One hundred and ninety-eight extracted human molars were randomly assigned into experimental groups according to the combination of independent variables: Acid [37% ortho-phosphoric acid (OPA), 40% meta-phosphoric acid (MPA) at pHs of: 0.5, 1 and 2] and Application Time [7, 15 and 30s]. Enamel-bond specimens were prepared and tested under μSBS. Resin-dentin beams were tested under μTBS tested immediately or after 6-months of water storage. Nanoleakage was evaluated using bonded-beams of each tooth/time-period. Enamel etching pattern and chemical and ultra-morphology analyses were also performed. The μSBS (MPa) data were subjected to a two-way repeated measures ANOVA (Acid vs. Application time). For μTBS, Acid vs application time vs storage time data were subjected to three-way ANOVA and Tukey's test (α = 0.05). MPA pH 0.5 showed μTBS similar to OPA, independently of the application time on enamel (p>0.05) or dentin (p>0.05). OPA provided higher nanoleakage values than MPA (p = 0.003). Significant decreases in TBS and increases in NL were only observed for OPA after 6 months (p = 0.001). An increase in the application time resulted in a more pronounced etching pattern for MPA. Chemical analysis showed that dentin demineralized by MPA depicted peaks of brushite and octacalcium phosphate. MPA exposed less collagen than OPA. However, optimal results for MPA were dependent on pH/application time. The use of 40% meta-phosphoric acid with a pH of 0.5 is an alternative acid

  2. The impact of hydrofluoric acid etching followed by unfilled resin on the biaxial strength of a glass-ceramic.

    Science.gov (United States)

    Posritong, Sumana; Borges, Alexandre Luiz Souto; Chu, Tien-Min Gabriel; Eckert, George J; Bottino, Marco A; Bottino, Marco C

    2013-11-01

    To evaluate the null hypotheses that hydrofluoric (HF) acid etching time would neither decrease the biaxial flexural strength of a glass-based veneering ceramic nor enhance it after silane and unfilled resin (UR) applications. Disc-shaped IPS e.max ZirPress specimens were allocated into 12 groups: G1-control (no-etching), G2-30 s, G3-60 s, G4-90 s, G5-120 s, G6-60 s+60 s. Groups (G7-G12) were treated in the same fashion as G1-G6, but followed by silane and UR applications. Surface morphology and roughness (Ra and Rq) of the ceramics were assessed by means of scanning electron microscopy (SEM) and profilometry, respectively. Flexural strength was determined by biaxial testing. Data were analyzed by two-way ANOVA and the Sidak test (α=0.05). Weibull statistics were estimated and finite element analysis (FEA) was carried out to verify the stress concentration end areas of fracture. The interaction (etching time vs. surface treatment) was significant for Ra (p=0.008) and Rq (0.0075). Resin-treated groups presented significantly lower Ra and Rq than non-treated groups, except for the 60s group (pceramic microstructure and that the UR was able to penetrate into the irregularities. A significant effect of etching time (p=0.029) on flexural strength was seen. G7-G12 presented higher strength than G1-G6 (pceramic flexural strength. Moreover, the flexural strength could be enhanced after UR treatment. Copyright © 2013 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  3. SOLVENT EFFECTS IN THE LIQUID-PHASE HYDRATION OF CYCLOHEXENE CATALYZED BY A MACROPOROUS STRONG ACID ION-EXCHANGE RESIN

    NARCIS (Netherlands)

    PANNEMAN, HJ; BEENACKERS, AACM

    1992-01-01

    The liquid-phase hydration of cyclohexene, a pseudo first order reversible reaction catalyzed by a strong acid ion exchange resin, macroporous Amberlite XE 307, was investigated in solvent mixtures of water and sulfolane. A decrease by a factor of 3 and 6 is observed in the experimentally measured

  4. Selective recovery of a pyridine derivative from an aqueous waste stream containing acetic acid and succinonitrile with solvent impregnated resins

    NARCIS (Netherlands)

    Bokhove, J.; Visser, T.J.; Schuur, Boelo; de Haan, A.B.

    2015-01-01

    Solvent impregnated resins (SIRs) were evaluated for the recovery of pyridine derivatives from an aqueous waste-stream containing also acetic acid and succinonitrile. For this purpose, a new solvent was developed, synthesized and impregnated in Amberlite XAD4. Sorption studies were used to determine

  5. Effect of Repeated Acid Challenges on the Color Stability of Resin-Infiltrated Enamel White Spot Lesions

    Science.gov (United States)

    2016-06-01

    seen in patients with xerostomia, poor oral hygiene, cariogenic diet, eating disorders , and orthodontic patients where bonded brackets provide... Effect of Repeated Acid Challenges on the Color Stability of Resin- Infiltrated Enamel White Spot Lesions by Robert A. Lummis...Jr. Lieutenant Commander, Dental Corps United States Public Health Service A thesis submitted to the Faculty of the Comprehensive

  6. Uranium loss from BISO-coated weak-acid-resin HTGR fuel

    International Nuclear Information System (INIS)

    Pearson, R.L.; Lindemer, T.B.

    1977-02-01

    Recycle fuel for the High-Temperature Gas-Cooled Reactor (HTGR) contains a weak-acid-resin (WAR) kernel, which consists of a mixture of UC 2 , UO 2 , and free carbon. At 1900 0 C, BISO-coated WAR UC 2 or UC 2 -UO 2 kernels lose a significant portion of their uranium in several hundred hours. The UC 2 decomposes and uranium diffuses through the pyrolytic coating. The rate of escape of the uranium is dependent on the temperature and the surface area of the UC 2 , but not on a temperature gradient. The apparent activation energy for uranium loss, ΔH, is approximately 90 kcal/mole. Calculations indicate that uranium loss from the kernel would be insignificant under conditions to be expected in an HTGR

  7. Low pressure process for continuous fiber reinforced polyamic acid resin matrix composite laminates

    Science.gov (United States)

    Druyun, Darleen A. (Inventor); Hou, Tan-Hung (Inventor); Kidder, Paul W. (Inventor); Reddy, Rakasi M. (Inventor); Baucom, Robert M. (Inventor)

    1994-01-01

    A low pressure processor was developed for preparing a well-consolidated polyimide composite laminate. Prepreg plies were formed from unidirectional fibers and a polyamic acid resin solution. Molding stops were placed at the sides of a matched metal die mold. The prepreg plies were cut shorter than the length of the mold in the in-plane lateral direction and were stacked between the molding stops to a height which was higher than the molding stops. The plies were then compressed to the height of the stops and heated to allow the volatiles to escape and to start the imidization reaction. After removing the stops from the mold, the heat was increased and 0 - 500 psi was applied to complete the imidization reaction. The heat and pressure were further increased to form a consolidated polyimide composite laminate.

  8. Improvement of epoxy resin properties by incorporation of TiO2 nanoparticles surface modified with gallic acid esters

    International Nuclear Information System (INIS)

    Radoman, Tijana S.; Džunuzović, Jasna V.; Jeremić, Katarina B.; Grgur, Branimir N.; Miličević, Dejan S.; Popović, Ivanka G.; Džunuzović, Enis S.

    2014-01-01

    Highlights: • Nanocomposites of epoxy resin and TiO 2 nanoparticles surface modified with gallates. • The T g of epoxy resin was increased by incorporation of surface modified TiO 2 . • WVTR of epoxy resin decreased in the presence of surface modified TiO 2 nanoparticles. • WVTR of nanocomposites was reduced with increasing gallates hydrophobic chain length. • Modified TiO 2 nanoparticles react as oxygen scavengers, inhibiting steel corrosion. - Abstract: Epoxy resin/titanium dioxide (epoxy/TiO 2 ) nanocomposites were obtained by incorporation of TiO 2 nanoparticles surface modified with gallic acid esters in epoxy resin. TiO 2 nanoparticles were obtained by acid catalyzed hydrolysis of titanium isopropoxide and their structural characterization was performed by X-ray diffraction and transmission electron microscopy. Three gallic acid esters, having different hydrophobic part, were used for surface modification of the synthesized TiO 2 nanoparticles: propyl, hexyl and lauryl gallate. The gallate chemisorption onto surface of TiO 2 nanoparticles was confirmed by Fourier transform infrared and ultraviolet–visible spectroscopy, while the amount of surface-bonded gallates was determined using thermogravimetric analysis. The influence of the surface modified TiO 2 nanoparticles, as well as the length of hydrophobic part of the gallate used for surface modification of TiO 2 nanoparticles, on glass transition temperature, barrier, dielectric and anticorrosive properties of epoxy resin was investigated by differential scanning calorimetry, water vapor transmission test, dielectric spectroscopy, electrochemical impedance spectroscopy and polarization measurements. Incorporation of surface modified TiO 2 nanoparticles in epoxy resin caused increase of glass transition temperature and decrease of the water vapor permeability of epoxy resin. The water vapor transmission rate of epoxy/TiO 2 nanocomposites was reduced with increasing hydrophobic part chain length of

  9. NORMAL FATTY ACID CONCENTRATIONS IN YOUNG CHILDREN WITH PHENYLKETONURIA (PKU).

    Science.gov (United States)

    Lavoie, Stacey M; Harding, Cary O; Gillingham, Melanie B

    2009-10-01

    The objective of this study was to determine if children with phenylketonuria (PKU) have lower fatty acid concentrations in total erythrocyte lipid due to the phenylalanine restricted diet therapy compared to healthy control subjects. Dietary intake and fatty acid concentrations in total erythrocyte lipid were measured in twenty-one subjects (PKU and twenty-three control children. Subjects with PKU had significantly lower protein and significantly higher polyunsaturated fat intake compared to controls. Subjects with PKU had significantly lower concentrations in total erythrocyte lipid of the sum of the omega-3,omega-6, saturated and polyunsaturated fatty acids. Concentrations of fatty acids among subjects with PKU were lower than control subjects but no subject with PKU exhibited any signs or symptoms suggestive of essential fatty acid deficiency, thereby suggesting that subjects with PKU in this cohort have normal and adequate essential fatty acid concentrations in total erythrocyte lipid.

  10. The effect of lamotrigine on valproic acid concentrations.

    Science.gov (United States)

    Martin, Andrew C; Besag, Frank M C; Berry, David J; Besag, Frank P

    2011-02-01

    To determine whether lamotrigine affects serum concentrations of valproic acid. Pre-morning-dose serum valproic acid concentrations were measured in 76 subjects with epilepsy (48 M, 28 F, age range 6-20 years, mean age 14 years) in whom lamotrigine was added while the dose of valproate and other medication remained unchanged. In a comparison group, either acetazolamide or gabapentin was added to sodium valproate. Far more subjects (26/76 = 34%) had an increase of >25% in valproic acid concentration with lamotrigine than those who had a decrease of >25% (4/76 = 5.3%). The mean valproic acid concentration before starting lamotrigine was 61.0 mg/L and on lamotrigine was 67.1 mg/L; the difference in means was 6.1 mg/L (standard error 2.1, 95% confidence limits 2.0, 10.2, p=0.004, highly significant, paired sample t-test, two-tailed), a rise of 10%. The change in valproic acid concentration appeared to depend on the initial valproic acid concentration (Pearson r=-0.405, pvalproate concentration was >50%, which could lead to toxicity, although the increase tended to occur with lower or intermediate initial valproic acid concentrations whereas a small overall decrease in valproic acid concentrations with lamotrigine was found with the higher initial valproic acid concentrations. One subject had abnormal bruising with the increased valproate level after lamotrigine was added, which resolved on decreasing the valproate dose. The changes in valproic acid concentrations in the comparison group were small (mean increase 2.6%) and were not statistically significant. Although there is a wide variation in the changes of valproic acid concentrations when lamotrigine is added, the concentrations tend to increase rather than decrease, especially with low or intermediate initial valproic acid concentrations. In some cases valproate toxicity, manifested by abnormal bruising, may result, although at higher initial valproic acid concentrations the valproic acid concentration usually

  11. Releasing Pattern of Applied Phosphorus and Distribution Change of Phosphorus Fractions in the Acid Upland Soils with Successive Resin Extraction

    Directory of Open Access Journals (Sweden)

    Arief Hartono

    2008-05-01

    Full Text Available The releasing pattern of applied P in the acid upland soils and the soil properties influencing the pattern were studied. Surface horizons of six acid upland soils from Sumatra, Java and Kalimantan were used in this study. The releasing pattern of applied P (300 mg P kg-1 of these soils were studied by successive resin extraction. P fractionation was conducted to evaluate which fractions released P to the soil solution after successive resin extraction. The cumulative of resin-Pinorganic (Pi release of soils was fitted to the first order kinetic. Regression analyses using factor scores obtained from the previous principal components analyses was applied to determine soil properties influencing P releasing pattern. The results suggested that the maximum P release was significantly (P < 0.05 increased by acidity plus 1.4 nm mineral-related factor (PC2 i.e. exchangeable Al and 1.4 nm minerals (smectite and vermiculite and decreased by oxide related factor (PC1 i.e. aluminum (Al plus 1/2 iron (Fe (by ammonium oxalate, crystalline Al and Fe oxides, cation exchange capacity, and clay content. P fractionation analysis after successive resin extraction showed that both labile and less labile in the form of NaHCO3-Pi and NaOH-Pi fractions, respectively, can be transformed into resin-Pi when in the most labile resin-Pi is depleted. Most of P released in high oxides soils were from NaOH-Pi fraction while in low oxides soils were from NaHCO3-Pi. P release from the former fraction resulted in the maximum P release lower than that of the latter one. When NaHCO3-Pi was high, NaOH-Pi was relatively more stable than NaHCO3-Pi despite resin-Pi removal. NaHCO3-Pi and NaOH-Pi are very important P fractions in replenishing resin-Pi in these acid upland soils.

  12. Uranium recovery and uranium remove from acid mine waters by ion exchange resin; Remocao e recuperacao de uranio de aguas acidas de mina com resina de troca ionica

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento, Marcos R.L. [Comissao Nacional de Energia Nuclear (CNEN), Pocos de Caldas, MG (Brazil). Coordenacao do Laborarorio; Fatibello Filho, Orlando [Sao Carlos Univ., SP (Brazil). Dept. de Quimica

    1999-11-01

    Ion exchange using resins is one of few processes capable of reducing contaminants in effluents to very low levels according to environmental legislation. In this study the process was used to remove and recovery uranium from acid mine waters at Pocos de Caldas-MG Uranium Mining and Milling Plant. The presence of pyrite in the waste rock piles, resulting acid drainage with several pollutants. Including uranium ranging from 6 to 14 mg/l, as sulfate complex, that can be removed by an anionic exchanger. Studies of uranium sorption without treatment, and with lime pretreatment of water to precipitate the iron and recovery uranium as commercial product, are presented. Uranium elution was done with NaCl solutions. Saline concentration and retention time were the parameters studied. the uranium decontaminations level in the effluents from acid mine water was 94%. (author) 10 refs., 6 tabs., 3 figs.

  13. Effect of the concentration of magnetite on the structure, electrical and magnetic properties of a polyester resin-based composite

    Directory of Open Access Journals (Sweden)

    Gabriel Peña-Rodriguez

    2018-01-01

    Full Text Available This study reports the effect of the concentration of magnetite powders (Fe3O4 on the electrical and magnetic properties of a resin-based composite of thermoset polyester. The samples were prepared by the casting method at different concentrations: 60-40, 70-30, 80-20, 90-10 and 100-0 (% in weight, where the primary phase was resin and the secondary, Fe3O4 powders. The crystalline structure was studied using X-ray diffraction and surface characterization was carried out applying the scanning electron microscopy technique. The electrical response was measured by electric polarization curves as a function of the electric field; and the volumetric electrical resistivity, by an electrometer. The magnetic response was determined by magnetization curves as a function of temperature and intensity of the applied magnetic field. The structural analysis indicates that crystallinity increases as higher concentrations of Fe3O4 are added to the samples. The electrical characterization of the material reveals that the volumetric resistivity decreases as the content of magnetite increases. These reactions indicate an insulation-conductor transition with increasing dielectric constant values. The magnetic characterization presents a linear increase of the saturation of magnetization and magnetic moment as a function of the amount of magnetite added to the polymer matrix, whereas the coercivity shows behaviors of soft magnetic materials for T ˃ Tv and for T < Tv, where Tv represents the temperature of Verwey.

  14. Effect of acid and alkaline hydrolysis on the concentrations of ...

    African Journals Online (AJOL)

    Thevetia peruviana seeds cake were defatted and then treated with varying concentrations each of hydrochloric acid, sodium hydroxide and calcium hydroxide solutions. Each product of hydrolysis was extracted with chloroform to isolate aglycones, the toxins of the seed. Various concentrations of hydrochloric acid and ...

  15. Biogenic glutamic acid-based resin: Its synthesis and application in the removal of cobalt(II).

    Science.gov (United States)

    Jamiu, Zakariyah A; Saleh, Tawfik A; Ali, Shaikh A

    2017-04-05

    Inexpensive biogenic glutamic acid has been utilized to synthesize a cross-linked dianionic polyelectrolyte (CDAP) containing metal chelating ligands. Cycloterpolymerization, using azoisobutyronitrile as an initiator, of N,N-diallylglutamic acid hydrochloride, sulfur dioxide and a cross-linker afforded a pH-responsive cross-linked polyzwitterionic acid (CPZA) which upon basification with NaOH was converted into CDAP. The new resin, characterized by a multitude of spectroscopic techniques as well as Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analyses, was evaluated for the removal of Co(II) as a model case under different conditions. The adsorption capacity of 137mgg -1 does indeed make the resin as one of the most effective sorbents in recent times. The resin leverages its cheap natural source and ease of regeneration in combination with its high and fast uptake capacities to offer a great promise for wastewater treatment. The resin has demonstrated remarkable efficiency in removing toxic metal ions including arsenic from a wastewater sample. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. Effect of the Acidic Dental Resin Monomer 10-methacryloyloxydecyl Dihydrogen Phosphate on Odontoblastic Differentiation of Human Dental Pulp Cells.

    Science.gov (United States)

    Kim, Eun-Cheol; Park, Haejin; Lee, Sang-Im; Kim, Sun-Young

    2015-11-01

    Although 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) is frequently used as an acidic resin monomer in dental adhesives, its effect on dental pulp cells (DPCs) has been rarely reported. The purpose of this study was to examine the effects of 10-MDP on the inflammatory response and odontoblastic differentiation of DPCs at minimally toxic concentrations. We found that 10-MDP caused the release of inflammatory cytokines including NO, PGE2, iNOS, COX-2, TNF-α, IL-1β, IL-6 and IL-8 in a concentration-dependent manner. In addition, 10-MDP reduced alkaline phosphatase activity, mineralization nodule formation and mRNA expression of odontoblastic differentiation markers such as dentin sialophosphoprotein, dentin matrix protein-1, osterix and Runx2 in a concentration-dependent manner with low toxicity. In addition, 10-MDP induced activation of nuclear factor-E2-related factor 2 (Nrf2) and its target gene, haeme oxygenase-1 (HO-1). We evaluated whether the effect of 10-MDP was related to the induction of HO-1 and found that treatment with a selective inhibitor of HO-1 reversed the production of 10-MDP-mediated pro-inflammatory cytokines and the inhibition of differentiation markers. Pre-treatment with either a GSH synthesis inhibitor or antioxidants blocked 10-MDP-induced mitogen-activated protein kinases (MAPKs), Nrf2 and NF-κB pathways. Taken together, the results of this study showed that minimally toxic concentrations of 10-MDP promoted an inflammatory response and suppressed odontoblastic differentiation of DPCs by activating Nrf2-mediated HO-1 induction through MAPK and NF-κB signalling. © 2015 Nordic Association for the Publication of BCPT (former Nordic Pharmacological Society).

  17. Fabrication of micro-dot arrays and micro-walls of acrylic acid/melamine resin on aluminum by AFM probe processing and electrophoretic coating

    Energy Technology Data Exchange (ETDEWEB)

    Kurokawa, S.; Kikuchi, T.; Sakairi, M. [Graduate School of Engineering, Hokkaido University, N-13, W-8, Kita-Ku, Sapporo 060-8628 (Japan); Takahashi, H. [Graduate School of Engineering, Hokkaido University, N-13, W-8, Kita-Ku, Sapporo 060-8628 (Japan)], E-mail: takahasi@elechem1-mc.eng.hokudai.ac.jp

    2008-11-30

    Micro-dot arrays and micro-walls of acrylic acid/melamine resin were fabricated on aluminum by anodizing, atomic force microscope (AFM) probe processing, and electrophoretic deposition. Barrier type anodic oxide films of 15 nm thickness were formed on aluminum and then the specimen was scratched with an AFM probe in a solution containing acrylic acid/melamine resin nano-particles to remove the anodic oxide film locally. After scratching, the specimen was anodically polarized to deposit acrylic acid/melamine resin electrophoretically at the film-removed area. The resin deposited on the specimen was finally cured by heating. It was found that scratching with the AFM probe on open circuit leads to the contamination of the probe with resin, due to positive shifts in the potential during scratching. Scratching of the specimen under potentiostatic conditions at -1.0 V, however, resulted in successful resin deposition at the film-removed area without probe contamination. The rate of resin deposition increased as the specimen potential becomes more positive during electrophoretic deposition. Arrays of resin dots with a few to several tens {mu}m diameter and 100-1000 nm height, and resin walls with 100-1000 nm height and 1 {mu}m width were obtained on specimens by successive anodizing, probe processing, and electrophoretic deposition.

  18. Immobilization of spent resin with epoxy resin

    International Nuclear Information System (INIS)

    Gultom, O.; Suryanto; Sayogo; Ramdan

    1997-01-01

    immobilization of spent resin using epoxy resin has been conducted. The spent resin was mixtured with epoxy resin in variation of concentration, i.e., 30, 40, 50, 60, 70 weight percent of spent resin. The mixture were pour into the plastic tube, with a diameter of 40 mm and height of 40 mm. The density, compressive strength and leaching rate were respectively measured by quanta chrome, paul weber apparatus and gamma spectrometer. The results showed that the increasing of waste concentration would be decreased the compressive strength, and increased density by immobilized waste. The leaching rate of 137 Cs from waste product was not detected in experiment (author)

  19. Effect of leaching residual methyl methacrylate concentrations on in vitro cytotoxicity of heat polymerized denture base acrylic resin processed with different polymerization cycles.

    Science.gov (United States)

    Bural, Canan; Aktaş, Esin; Deniz, Günnur; Ünlüçerçi, Yeşim; Bayraktar, Gülsen

    2011-08-01

    Residual methyl methacrylate (MMA) may leach from the acrylic resin denture bases and have adverse effects on the oral mucosa. This in vitro study evaluated and correlated the effect of the leaching residual MMA concentrations ([MMA]r) on in vitro cytotoxicity of L-929 fibroblasts. A total of 144 heat-polymerized acrylic resin specimens were fabricated using 4 different polymerization cycles: (1) at 74ºC for 9 h, (2) at 74ºC for 9 h and terminal boiling (at 100ºC) for 30 min, (3) at 74ºC for 9 h and terminal boiling for 3 h, (4) at 74ºC for 30 min and terminal boiling for 30 min. Specimens were eluted in a complete cell culture medium at 37ºC for 1, 2, 5 and 7 days. [MMA]r in eluates was measured using high-performance liquid chromatography. In vitro cytotoxicity of eluates on L-929 fibroblasts was evaluated by means of cell proliferation using a tetrazolium salt XTT (sodium 3´-[1-phenyl-aminocarbonyl)-3,4-tetrazolium]bis(4-methoxy-6-nitro)benzenesulphonic acid) assay. Differences in [MMA]r of eluates and cell proliferation values between polymerization cycles were statistically analyzed by Kruskal-Wallis, Friedman and Dunn's multiple comparison tests. The correlation between [MMA]r of eluates and cell proliferation was analyzed by Pearson's correlation test (p<0.05). [MMA]r was significantly (p<0.001) higher in eluates of specimens polymerized with cycle without terminal boiling after elution of 1 and 2 days. Cell proliferation values for all cycles were significantly (p<0.01) lower in eluates of 1 day than those of 2 days. The correlation between [MMA]r and cell proliferation values was negative after all elution periods, showing significance (p<0.05) for elution of 1 and 2 days. MMA continued to leach from acrylic resin throughout 7 days and leaching concentrations markedly reduced after elution of 1 and 2 days. Due to reduction of leaching residual MMA concentrations, use of terminal boiling in the polymerization process for at least 30 min and water

  20. Effect of leaching residual methyl methacrylate concentrations on in vitro cytotoxicity of heat polymerized denture base acrylic resin processed with different polymerization cycles

    Directory of Open Access Journals (Sweden)

    Canan Bural

    2011-08-01

    Full Text Available OBJECTIVES: Residual methyl methacrylate (MMA may leach from the acrylic resin denture bases and have adverse effects on the oral mucosa. This in vitro study evaluated and correlated the effect of the leaching residual MMA concentrations ([MMA]r on in vitro cytotoxicity of L-929 fibroblasts. MATERIAL AND METHODS: A total of 144 heat-polymerized acrylic resin specimens were fabricated using 4 different polymerization cycles: (1 at 74ºC for 9 h, (2 at 74ºC for 9 h and terminal boiling (at 100ºC for 30 min, (3 at 74ºC for 9 h and terminal boiling for 3 h, (4 at 74ºC for 30 min and terminal boiling for 30 min. Specimens were eluted in a complete cell culture medium at 37ºC for 1, 2, 5 and 7 days. [MMA]r in eluates was measured using high-performance liquid chromatography. In vitro cytotoxicity of eluates on L-929 fibroblasts was evaluated by means of cell proliferation using a tetrazolium salt XTT (sodium 3´-[1-phenyl-aminocarbonyl-3,4-tetrazolium]bis(4-methoxy-6-nitrobenzenesulphonic acid assay. Differences in [MMA]r of eluates and cell proliferation values between polymerization cycles were statistically analyzed by Kruskal-Wallis, Friedman and Dunn's multiple comparison tests. The correlation between [MMA]r of eluates and cell proliferation was analyzed by Pearson's correlation test (p<0.05. RESULTS: [MMA]r was significantly (p<0.001 higher in eluates of specimens polymerized with cycle without terminal boiling after elution of 1 and 2 days. Cell proliferation values for all cycles were significantly (p<0.01 lower in eluates of 1 day than those of 2 days. The correlation between [MMA]r and cell proliferation values was negative after all elution periods, showing significance (p<0.05 for elution of 1 and 2 days. MMA continued to leach from acrylic resin throughout 7 days and leaching concentrations markedly reduced after elution of 1 and 2 days. CONCLUSION: Due to reduction of leaching residual MMA concentrations, use of terminal boiling in

  1. The mechanism of ion exchange and adsorption coexist on medium-low concentration ammonium-nitrogen removal by ion-exchange resin.

    Science.gov (United States)

    Yunnen, Chen; Xiaoyan, Luo; Changshi, Xiong; Liming, Liang

    2015-01-01

    In this study, the removal of medium-low concentration ammonium-nitrogen ([Formula: see text]) from waters and wastewaters on D113 resin was investigated with respect to pH, initial [Formula: see text] concentration, temperature and contact time. The equilibrium of [Formula: see text] on D113 resin reached in 20-30 min. The process of [Formula: see text] removal by D113 resin fitted Langmuir isotherm well. The pseudo second-order kinetic and intra-particle diffusion models were used to investigate the kinetic data of [Formula: see text] on D113 resin. The desorption solution can be returned to production after pretreatment. The mechanism of removal of [Formula: see text] by D113 resin was coexistence of adsorption and cation exchange. When the dosage of D113 resin was 5 g L(-1), pH 6, contact 30 min at room temperature, initial [Formula: see text] concentration being 116 mg L(-1) in rare earth metallurgical wastewater was reduced to 13 mg L(-1) after adsorption treatment.

  2. Abietic acid isolated from pine resin (Resina Pini) enhances angiogenesis in HUVECs and accelerates cutaneous wound healing in mice.

    Science.gov (United States)

    Park, Jun Yeon; Lee, Yun Kyung; Lee, Dong-Soo; Yoo, Jeong-Eun; Shin, Myoung-Sook; Yamabe, Noriko; Kim, Su-Nam; Lee, Seulah; Kim, Ki Hyun; Lee, Hae-Jeung; Roh, Seok Sun; Kang, Ki Sung

    2017-05-05

    Resin known as Resina Pini is listed in the Korean and Japanese pharmacopoeias and has been used for treating skin wounds and inflammation. Resin is composed of more than 50% abietic acid and 10% neutral substances. In the present study, the wound-healing effects of abietic acid and the possible underlying mechanism of action were investigated in various in vitro and in vivo models. The effects of abietic acid on tube formation and migration were measured in human umbilical vein vascular endothelial cells (HUVECs). Protein expression of mitogen-activated protein kinase (MAPK) activation was evaluated via Western blotting analysis. The wound-healing effects of abietic acid were assessed using a mouse model of cutaneous wounds. The results showed that abietic acid enhanced cell migration and tube formation in HUVECs. Abietic acid induced significant angiogenic potential, which is associated with upregulation of extracellular signal-regulated kinase (ERK) and p38 expression. Additionally, 0.8μM abietic acid-treated groups showed accelerated wound closure compared to the controls in a mouse model of cutaneous wounds. The current data indicate that abietic acid treatment elevated cell migration and tube formation in HUVECs by the activation of ERK and p38 MAPKs. We suggest that abietic acid can be developed as a wound-healing agent. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Di-D-fructose dianhydride-enriched products by acid ion-exchange resin-promoted caramelization of D-fructose: chemical analyses.

    Science.gov (United States)

    Suárez-Pereira, Elena; Rubio, Enrique M; Pilard, Serge; Ortiz Mellet, Carmen; García Fernández, José M

    2010-02-10

    Caramelization commonly occurs when sugars, or products containing a high proportion of sugars, are heated either dry or in concentrated aqueous solutions, alone or in the presence of certain additives. Upon thermal treatment of sugars, dehydration and self-condensation reactions occur, giving rise to volatiles (principally 2-hydroxymethylfurfural, HMF), pigments (melanoidines) and oligosaccharidic material, among which di-D-fructose dianhydrides (DFAs) and glycosylated DFA derivatives of different degree of polymerization (DP) have been identified. This study reports a methodology to produce caramel-like products with a high content of DFAs and oligosaccharides thereof from commercial D-fructose based on the use of acid ion-exchange resins as caramelization promotors. The rate of formation of these compounds as a function of D-fructose concentration, catalyst proportion, temperature, catalyst nature and particle size has been investigated. The use of sulfonic acid resins allows conducting caramelization at remarkable low temperatures (70-90 degrees C) to reach conversions into DFA derivatives up to 70-80% in 1-2 h, with relative proportions of HMF < 2%.The relative abundance of individual DFA structures can be modulated by acting on the catalyst nature and reaction conditions, which offers a unique opportunity for nutritional studies of DFA-enriched products with well-defined compositions.

  4. Retention of Ascorbic Acid and Solid Concentration via Centrifugal Freeze Concentration of Orange Juice

    Directory of Open Access Journals (Sweden)

    P. Orellana-Palma

    2017-01-01

    Full Text Available Freeze concentration of liquid foods produces high-quality concentrates while retaining the heat-labile compounds found in fresh samples. Centrifugal freeze concentration is a cryoconcentration method assisted by an external force, centrifugation, to enhance the separation of concentrate from the ice. When applying centrifugal freeze concentration to orange juice, after the third cryoconcentration cycle, the ascorbic acid content in the concentrate showed retention close to 70% of the initial value. After the third cycle, the solutes in the concentrate increased 4 times the initial value of the fresh sample with 70% efficiency. The color evaluation showed that the final concentrated fraction was darker than the fresh juice. The centrifugal freeze concentration in orange juice was effective for obtaining a high-quality concentrate with a higher concentration of solids and ascorbic acid retention.

  5. ORGANIC ACIDS CONCENTRATION IN WINE STOCKS AFTER Saccharomyces cerevisiae FERMENTATION

    Directory of Open Access Journals (Sweden)

    V. N. Bayraktar

    2013-04-01

    Full Text Available The biochemical constituents in wine stocks that influence the flavor and quality of wine are investigated in the paper. The tested parameters consist of volume fraction of ethanol, residual sugar, phenolic compounds, tartaric, malic, citric, lactic, acetic acids, titratable acidity and volatile acids. The wine stocks that were received from white and red grape varieties Tairov`s selection were tested. There was a correlation between titratable acidity and volatile acids in the wine stocks from white and red grape varieties. High correlation was also found between lactic and acetic acids, between volatile acids, acetic acid and sugar. It was determined that wine stocks with a high concentration of ethanol originated from those yeast strains of Saccharomyces cerevisiae, in a fermented grape must of high speed of enzyme activity. The taste of wine stocks correlated with the ratio of tartaric to malic acid. Analysis showed significant differences between the varieties of white and red wine stocks in concentrations of organic acids, phenolic compounds, residual sugar, and volume fraction of ethanol. Positive correlation was indicated for both studied groups for volatile acids and acetic acid, tartaric, malic, lactic acids and total sugar. Prospective yeast cultures with high productivity of alcohol (ethanol were selected for winemaking biotechnology.

  6. Study and application on lean resin converting in uranium mill

    International Nuclear Information System (INIS)

    Zhao Shaoxi; Huang Qijin; Zhu Shuguang; Yi Faqing; Du Wenjie

    2012-01-01

    The field test about sulphuric acid used to convert lean resin was finished. The results indicated sulphuric acid could replace chlorin in lean resin and could be reclaimed to desorption procedure. The consumption of NaCl decreased, the chlorin concentration of tailing decreased too. Both of uranium loss and waste water volume were reduced. The uranium concentration of tailing decreased and energy saving and emission reduction can be achieved. (authors)

  7. Reduction of polyester resin shrinkage by means of epoxy resin

    International Nuclear Information System (INIS)

    Pietrzak, M.; Brzostowski, A.

    1981-01-01

    An attempt was made to decrease the shrinkage of unsaturated polyester resin, taking place during radiation-induced curing, by the addition of epoxy resin. In order to combine chemically both resins, the epoxy component was modified with cinnamic and acrylic acids. A composition of 90 parts of polyester resin, 10 parts of epoxy resin modified with cinnamic acid, and 150 parts of a silica filler showed a volume shrinkage of 1.2%. (author)

  8. Distribution of 14 elements from two solutions simulating Hanford HLW Tank 102-SY (acid-dissolved sludge and acidified supernate) on four cation exchange resins and five anion exchange resins having different functional groups

    International Nuclear Information System (INIS)

    Marsh, S.F.; Svitra, Z.V.; Bowen, S.M.

    1995-01-01

    As part of the Tank Waste Remediation System program at Los Alamos, we evaluated a series of cation exchange and anion exchange resins for their ability to remove hazardous components from radioactive high-level waste (HLW). The anion exchangers were Reillex TM HPQ, a polyvinyl pyridine resin, and four strong-base polystyrene resins having trimethyl, tri ethyl, tri propyl, and tributyl amine as their respective functional groups. The cation exchange resins included Amberlyst TM 15 and Amberlyst tM XN-1010 with sulfonic acid functionality, Duolite TM C-467 with phosphonic acid functionality, and poly functional Diphonix TM with di phosphonic acid, sulfonic acid, and carboxylic acid functionalities. We measured the distributions of 14 elements on these resins from solutions simulating acid-dissolved sludge (pH 0.6) and acidified supernate (pH 3.5) from underground storage tank 102-SY at the Hanford Reservation near Richland, Washington, USA. To these simulants, we added the appropriate radionuclides and used gamma spectrometry to measure fission products (Ce, Cs, Sr, Tc, and Y), actinides (U, Pu, and Am), and matrix elements (Cr, Co, Fe, Mn, Zn, and Zr). For each of the 252 element/resin/solution combinations, distribution coefficients (Kds) were measured for dynamic contact periods of 30 minutes, 2 hours, and 6 hours to obtain information about sorption kinetics from these complex media. Because we measured the sorption of many different elements, the tabulated results indicate which unwanted elements are most likely to interfere with the sorption of elements of special interest. On the basis of these 756 measured Kd values, we conclude that some of the tested resins appear suitable for partitioning hazardous components from Hanford HLW. (author). 10 refs., 11 tabs

  9. Synthesis of novel chitosan resin derivatized with serine moiety for the column collection/concentration of uranium and the determination of uranium by ICP-MS

    International Nuclear Information System (INIS)

    Oshita, Koji; Oshima, Mitsuko; Gao Yunhua; Lee, Kyue-Hyung; Motomizu, Shoji

    2003-01-01

    A chitosan resin derivatized with serine moiety (serine-type chitosan) was newly developed by using the cross-linked chitosan as a base material. The adsorption behavior of trace amounts of metal ions on the serine-type chitosan resin was systematically examined by packing it in a mini-column, passing a metal solution through it and measuring metal ions in the effluent by ICP-MS. The resin could adsorb a number of metal cations at pH from neutral to alkaline region, and several oxoanionic metals at acidic pH region by an anion exchange mechanism. Uranium and Cu could be adsorbed selectively at pH from acidic to alkaline region by a chelating mechanism; U could be adsorbed quantitatively even at pH 3-4. Uranium adsorbed on the resin was easily eluted with 1 M nitric acid: the preconcentration (5-, 10-, 50- and 100-fold) of U was possible. The column treatment method was used prior to the ICP-MS measurement of U in natural river, sea and tap waters; R.S.D. were 2.63, 1.13 and 1.37%, respectively. Uranium in tap water could be determined by 10-fold preconcentration: analytical result was 1.46±0.02 ppt. The resin also was applied to the recovery of U in sea water: the recovery tests for artificial and natural sea water were 97.1 and 93.0%, respectively

  10. Efficient in situ separation and production of L-lactic acid by Bacillus coagulans using weak basic anion-exchange resin.

    Science.gov (United States)

    Zhang, Yitong; Qian, Zijun; Liu, Peng; Liu, Lei; Zheng, Zhaojuan; Ouyang, Jia

    2018-02-01

    To get rid of the dependence on lactic acid neutralizer, a simple and economical approach for efficient in situ separation and production of L-lactic acid was established by Bacillus coagulans using weak basic anion-exchange resin. During ten tested resins, the 335 weak basic anion-exchange resins demonstrated the highest adsorption capacity and selectivity for lactic acid recovery. The adsorption study of the 335 resins for lactic acid confirmed that it is an efficient adsorbent under fermentation condition. Langmuir models gave a good fit to the equilibrium data at 50 °C and the maximum adsorption capacity for lactic acid by 335 resins was about 402 mg/g. Adsorption kinetic experiments showed that pseudo-second-order kinetics model gave a good fit to the adsorption rate. When it was used for in situ fermentation, the yield of L-lactic acid by B. coagulans CC17 was close to traditional fermentation and still maintained at about 82% even after reuse by ten times. These results indicated that in situ separation and production of L-lactic acid using the 335 resins were efficient and feasible. This process could greatly reduce the dosage of neutralizing agent and potentially be used in industry.

  11. Plasma Concentration of Ascorbic Acid and Some Hematological ...

    African Journals Online (AJOL)

    hanumantp

    acid, which is a vital antioxidant, and blood cell production or morphology may be affected. Objective: To investigate the ... not adversely affect plasma ascorbic acid concentration and hematological parameters in adult humans. The study, however .... peroxidase/H202 halide system in vitro and in vivo. Am J Clin. Nutr 1995 ...

  12. Novel polysiloxane resin functionalized with dicyclohexano-18-crown-6 (DCH18C6): Synthesis, characterization and extraction of Sr(II) in high acidity HNO3 medium.

    Science.gov (United States)

    Ye, Gang; Bai, Feifei; Wei, Jichao; Wang, Jianchen; Chen, Jing

    2012-07-30

    A novel kind of polysiloxane resin functionalized with dicyclohexano-18-crown-6 (DCH18C6) was synthesized through a post-modification approach. The DCH18C6 moieties bearing amino groups were firstly prepared, followed by covalent grafting to a silica precursor P-(CH(2))(3)-Cl (Where P represents a 3-dimentional polymerized silica matrix) based on nucleophilic substitution reaction. (29)Si and (13)C solid-state NMR, FT-IR, XPS, TGA, ESEM and elemental analysis were employed to systematically characterize the structure, thermal property and surface morphology of the functionalized resin. The results indicated that the DCH18C6 ligands were successfully bonded to the polysiloxane resin with a satisfactory grafting degree (33.6wt.%). Due to the robust organosilica framework and the covalent immobilization of the ligands, the functionalized resin had excellent thermal stability and acid resistance. Batch experiments showed that the resin could effectively separate Sr(II) in high acidity mediums. The distribution coefficient (K(d)) of 43.6cm(3)/g could be achieved in 5.0mol/L HNO(3) solution. The influences of contact time and acidity of HNO(3) on the resin's extraction performance were examined. The reusability and the selectivity to Sr(II) over interference ions were investigated. The DCH18C6-functionalized resin might be potentially applied for the radiostrontium removal in the high level liquid waste (HLLW). Copyright © 2012 Elsevier B.V. All rights reserved.

  13. Predicting the Viscosity of Low VOC Vinyl Ester and Fatty Acid-Based Resins

    National Research Council Canada - National Science Library

    LaScala, John J; Jeyarajasingam, Amutha; Winston, Cherise; Sand, James M; Palmese, Guiseppe R

    2005-01-01

    .... The viscosities of these resins were measured as a function of reactive diluent content and type, temperature, and vinyl ester molecular weight to determine the operating window for composite manufacture...

  14. [Effect of hydrofluoric acid etching time and resin bonding on the flexural strength of lithium disilicate glass ceramic].

    Science.gov (United States)

    Ren, Dong-feng; Luo, Xiao-ping

    2013-08-01

    To analyze the effect of hydrofluoric acid(HFA) etching time and resin bonding on the flexural strength of IPS e.max® Press glass ceramic, and evaluate the efficacy of resin cements to seal the cracks of the etched ceramic. Two hundred and twenty-five bars (25.0 mm×3.0 mm×2.0 mm) were made from IPS e.max® Press ingots using lost-wax, hot-pressed ceramic fabrication technology and randomly divided into five groups, forty-five each.In each group, the surfaces of ceramic bars were etched by 9.5% HFA gel for 0, 20, 40, 60 and 120 s respectively. Three specimens from each group were selected to observe the microstructure by the field emission scanning electron microscope (FE-SEM). Then each group were randomly subdivided into two subgroups (n = 20).One subgroup were coverd with a thin (approximately 0.1 mm) layer of resin cement (Variolink N), whereas the other subgroup remained unaltered.Half of the specimens were stored in 37°C water bath for 24 h and the other half went through thermocycle 10 000 times before 3-point bending test to determine their flexural strength.Interfaces between resin cement and etched ceramic were examined with FE-SEM. FE-SEM results showed that etching with HFA resulted in preferential dissolution of glass ceramic, and partially supported crystals within the glass matrix were lost with the increasing of etching time.FE-SEM indicated that resin cement sealed the cracks and defects and bonded tightly to etched ceramic surface. The mean flexural strength values of group 0, 20, 40, 60 and 120 s were (384 ± 33), (347 ± 43), (330 ± 53), (327 ± 67) , and (317 ± 41) MPa respectively. The mean flexural strength of each group except group 0 s increased significantly to (420 ± 31), (435 ± 50), (400 ± 39), and (412 ± 58) MPa respectively after the application of resin cement. Overtime HFA etching could have a wakening effect on IPS e.max® Press glass-ceramic. The application of dual-curing resin cement can compensate the strength loss of

  15. Removing and recovering of uranium from the acid mine waters by using ion exchange resin; Remocao e recuperacao de uranio de aguas acidas de mina por resina de troca ionica

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento, Marcos Roberto Lopes do

    1998-07-01

    Ion exchange using resins is one of the few processes capable of reducing ionic contaminants in effluents to very low levels. In this study the process was used to remove and recovery uranium from acid mine waters at Pocos de Caldas-MG Uranium Mining and Milling Plant. The local mineralogical features, allied to the biogeochemical phenomena, owing to presence of pyrite in the rock piles, moreover another factors, resulting acid drainage with several pollutants, including uranium ranging from 6 to 14 mg/l, as sulfate complex, that can be removed by anionic exchanger. The iron interference is eliminated by lime pretreatment of water, increasing pH from 2.6 to 3.3-3.8 to precipitate this cation, without changing the uranium amount. Eight anionic resins were tested, based on the uranium loading, in sorption studies. Retention time, and pH influence was verified for the exchanger chose. With breakthrough of 1 mg U/L and 10 mg U/l in the feed solution, the uranium decontamination level was 94%. Typical values of loading resin were 20-30 g U/l and 70-90 g SO{sub 4}/l. Uranium elution was done with Na Cl solution. Retention time, saline, and acid concentration were the parameters studied. The concentrate, obtained from the eluate by ammonia precipitation, presented uranium (86,8% as U{sub 3} O{sub 8}) and impurities within commercial specifications. (author)

  16. In vivo and in vitro evaluation of the efficacy of a peracetic acid-based disinfectant for decontamination of acrylic resins.

    Science.gov (United States)

    Chassot, Ana Lúcia Campani; Poisl, Maria Inês Pereira; Samuel, Susana Maria Werner

    2006-01-01

    The purpose of this study was to assess the antimicrobial efficacy of a peracetic acid-based disinfectant for decontamination of heat-polymerized, chemically activated and microwave-polymerized acrylic resins. Resin plates were contaminated in vivo upon intraoral use by 10 volunteers for 7 nights and slabs were contaminated in vitro by contact with Bacillus subtilis and Bacillus stearothermophilus. The contaminated acrylic resin specimens were immersed in a 0.2% peracetic acid-based disinfectant (Sterilife; Lifemed) for 5 min or 10 min and placed in a BHI culture medium. After incubation at 37 degrees C for 48 h, bacterial growth was assessed by analyzing turbidity of the medium. For all types of acrylic resin, no turbidity of the medium was observed for any of the resin specimens immersed in the peracetic acid-based disinfectant for either 5 or 10 min. On the other hand, the media with specimens that were not immersed in the disinfectant (control) showed turbidity in 100% of the cases, indicating the presence of microorganisms in both tested conditions. In conclusion, immersion for at least 5 min in a 0.2% peracetic acid-based disinfectant promoted high-level disinfection of heat-polymerized, chemically activated and microwave-polymerized acrylic resins contaminated with either human saliva or Bacillus subtilis or Bacillus stearothermophilus.

  17. Plant-Scale Concentration Column Designs for SHINE Target Solution Utilizing AG 1 Anion Exchange Resin

    Energy Technology Data Exchange (ETDEWEB)

    Stepinski, Dominique C. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, G. F. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-09-30

    Argonne is assisting SHINE Medical Technologies (SHINE) in their efforts to develop SHINE, an accelerator-driven process that will utilize a uranyl-sulfate solution for the production of fission product Mo-99. An integral part of the process is the development of a column for the separation and recovery of Mo-99, followed by a concentration column to reduce the product volume from 15-25 L to <1 L. Argonne has collected data from batch studies and breakthrough column experiments to utilize the VERSE (Versatile Reaction Separation) simulation program (Purdue University) to design plant-scale product recovery and concentration processes.

  18. LA-ICP-MS of rare earth elements concentrated in cation-exchange resin particles for origin attribution of uranium ore concentrate.

    Science.gov (United States)

    Asai, Shiho; Limbeck, Andreas

    2015-04-01

    Rare earth elements (REE) concentrated on cation-exchange resin particles were measured with laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) to obtain chondrite-normalized REE plots. The sensitivity of REE increased in ascending order of the atomic number, according to the sensitivity trend in pneumatic nebulization ICP-MS (PN-ICP-MS). The signal intensities of REE were nearly proportional to the concentrations of REE in the immersion solution used for particle-preparation. Minimum measurable concentration calculated from the net signals of REE was approximately 1 ng/g corresponding to 0.1 ng in the particle-preparation solution. In LA analysis, formation of oxide and hydroxide of the light REE and Ba which causes spectral interferences in the heavy REE measurement was effectively attenuated due to the solvent-free measurement capability, compared to conventional PN-ICP-MS. To evaluate the applicability of the proposed method, the REE-adsorbed particles prepared by immersing them in a U-bearing solution (commercially available U standard solution) were measured with LA-ICP-MS. Aside from the LA analysis, each concentration of REE in the same U standard solution was determined with conventional PN-ICP-MS after separating REE by cation-exchange chromatography. The concentrations of REE were ranging from 0.04 (Pr) to 1.08 (Dy) μg/g-U. The chondrite-normalized plot obtained through LA-ICP-MS analysis of the U standard sample exhibited close agreement with that obtained through the PN-ICP-MS of the REE-separated solution within the uncertainties. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Effect of a self-etching primer and phosphoric acid etching on the bond strength of 4-META/MMA-TBB resin to human enamel.

    Science.gov (United States)

    Nogawa, Hiroshi; Koizumi, Hiroyasu; Saiki, Osamu; Hiraba, Haruto; Nakamura, Mitsuo; Matsumura, Hideo

    2015-01-01

    The purpose of this study was to evaluate the shear bond strength and durability of 4-META/MMA-TBB resin to human enamel. A self-etching primer that contained 4-META (Teeth Primer, TP) and 35-45% or 60-65% concentrations of phosphoric acid (K-Etchant Gel, KE, and Super Bond C&B Red Activator, RA) were used as the surface treatment agents. A methyl methacrylate (MMA)-based self-polymerizing resin (Super-Bond C&B) was used as a luting agent. The shear bond strength was determined both pre and post thermocycling. The results were statistically analyzed with a non-parametric procedure. The post-thermocycling shear bond strength of the TP group was significantly higher than that of other groups, and that of the KE group was significantly higher compared with the RA group. These results demonstrated that 4-META was effective. Furthermore, when the degree of tooth demineralization was compared, surface treatment with less demineralization using TP was the most effective treatment.

  20. gastric acid secretion, mucus concentration and ulceration following ...

    African Journals Online (AJOL)

    Physiology

    This study was carried out to evaluate the effect of consumption (ingestion) of Cannabis sativa on the gastrointestinal tract using mucus concentration, acid secretion and ulceration in animal (rats) model as indices. Three groups of six (6) rats each were used. The control group were fed on rat chow only while another group ...

  1. Effects of the peracetic acid and sodium hypochlorite on the colour stability and surface roughness of the denture base acrylic resins polymerised by microwave and water bath methods.

    Science.gov (United States)

    Fernandes, Flavio H C N; Orsi, Iara A; Villabona, Camilo A

    2013-03-01

    This study evaluated the surface roughness (Ra) and color stability of acrylic resin colors (Lucitone 550, QC-20 and Vipi-Wave) used for fabricating bases for complete, removable dentures, overdentures and prosthetic protocol after immersion in chemical disinfectants (1% sodium hypochlorite and 2% peracetic acid) for 30 and 60 minutes. Sixty specimens were made of each commercial brand of resin composite, and divided into 2 groups according to the chemical disinfectants. Specimens had undergone the finishing and polishing procedures, the initial color and roughness measurements were taken (t=0), and after this, ten test specimens of each commercial brand of resin composite were immersed in sodium hypochlorite and ten in peracetic acid, for 30 and 60 minutes, with measurements being taken after each immersion period. These data were submitted to statistical analysis. There was evidence of an increase in Ra after 30 minutes immersion in the disinfectants in all the resins, with QC-20 presenting the highest Ra values, and Vipi-Wave the lowest. After 60 minutes immersion in the disinfectants all the resins presented statistically significant color alteration. Disinfection with 1% sodium hypochlorite and peracetic acid altered the properties of roughness and color of the resins. © 2012 The Gerodontology Society and John Wiley & Sons A/S.

  2. Fully automated concentration control of the acidic texturisation process

    OpenAIRE

    Dannenberg, T.; Zimmer, M.; Rentsch, J.

    2012-01-01

    To enable a concentration control in the acidic texturing process we have closed the feedback loop from analytical data to the dosing mechanism of the used process tool. In order to analyze the process bath we used near-infrared spectroscopy in an online setup as well as ion chromatography as an inline method in a second approach. Using the developed dosing algorithm allows a concentration optimization of HF and HNO3 in dependence of the Si concentrations. This allows a further optimization o...

  3. The bile acid-sequestering resin sevelamer eliminates the acute GLP-1 stimulatory effect of endogenously released bile acids in patients with type 2 diabetes

    DEFF Research Database (Denmark)

    Brønden, Andreas; Albér, Anders; Rohde, Ulrich

    2018-01-01

    of the present study was to assess the GLP-1 secretory and gluco-metabolic effects of endogenously released bile, with and without concomitant administration of the bile acid-sequestering resin, sevelamer, in patients with type 2 diabetes. MATERIALS AND METHODS: We performed a randomized, placebo......-controlled, and double-blinded cross-over study including 15 metformin-treated patients with type 2 diabetes. Four experimental study days in randomized order with administration of either sevelamer 3,200 mg or placebo in combination with intravenous infusion of cholecystokinin (CCK) (0.4 pmol sulfated CCK-8/kg...... was shown to eliminate the acute bile acid-induced increase in plasma GLP-1 excursions. CONCLUSIONS: Single-dose administration of sevelamer eliminated bile acid-mediated GLP-1 secretion in patients with type 2 diabetes, which could be explained by reduced bile acid stimulation of the basolaterally...

  4. Treatment and conditioning of spent ion exchange resins from research reactors, precipitation sludges and other radioactive concentrates

    International Nuclear Information System (INIS)

    1993-02-01

    Spent radioactive ion exchange resins, precipitation sludges and evaporator concentrates are generated from the treatment of aqueous waste streams at nuclear research centres and from the use of radioisotopes in research and medical or industrial applications. A strategy for the effective management of these wastes from generation to disposal is necessary to ensure their safe handling, conditioning, storage and disposal to avoid detrimental effects on health and the environment. This report describes the factors to be considered in the development and selection of appropriate strategies for managing these types of wastes. Waste characteristics, pretreatment requirements, conditioning processes, packaging, and properties of the conditioned products are discussed. In addition, safety considerations and quality assurance needs are addressed. The report is intended to provide guidance to Member States that do not have nuclear power generation programmes. Several processes and procedures are presented, though preference is given to the simpler, easy-to-operate processes requiring relatively unsophisticated and inexpensive equipment. 24 refs, 20 figs, 13 tabs

  5. Changes in volatile terpene and diterpene resin acid composition of resistant and susceptible white spruce leaders exposed to simulated white pine weevil damage.

    Science.gov (United States)

    Tomlin, E S; Antonejevic, E; Alfaro, R I; Borden, J H

    2000-10-01

    Induced (traumatic) resin in white spruce (Picea glauca (Moench) Voss) leaders resistant or susceptible to the white pine weevil (Pissodes strobi Peck) was analyzed for volatile terpenes and diterpene resin acids after simulated white pine weevil damage. Leaders from 331 trees were wounded just below the apical bud with a 1-mm diameter drill, coinciding with the natural time of weevil oviposition in the spring. Leaders were removed in the fall, and the bark and xylem from the upper and lower regions of the leader extracted and analyzed by gas chromatography. Unwounded trees had low amounts of resin in xylem compared with bark. In response to wounding, volatile terpenes and diterpene resin acids increased in the upper xylem (area of wounding), with resistant trees showing a greater increase than susceptible trees. Wounding caused monoterpenes in particular to decrease in the lower region of the leader (away from the drilled area) in greater amounts in susceptible trees than in resistant trees. In response to wounding, the proportion of monoterpene to resin acid increased in the upper and lower xylem of resistant trees, and slightly increased in the upper xylem of susceptible trees. Monoterpene-enriched resin is more fluid than constitutive resin, and probably flows more readily into oviposition cavities and larval mines, where it may kill immature weevils. Loss of resin components in the lower xylem suggested catabolism and transport of these materials to the site of wounding; however, energetic and regulatory data are necessary to confirm this hypothesis. This study provides a basis for measuring the ability of a tree to undergo traumatic resinosis that could be used to screen for resistance to white pine weevil.

  6. Conifer Diterpene Resin Acids Disrupt Juvenile Hormone-Mediated Endocrine Regulation in the Indian Meal Moth Plodia interpunctella.

    Science.gov (United States)

    Oh, Hyun-Woo; Yun, Chan-Seok; Jeon, Jun Hyoung; Kim, Ji-Ae; Park, Doo-Sang; Ryu, Hyung Won; Oh, Sei-Ryang; Song, Hyuk-Hwan; Shin, Yunhee; Jung, Chan Sik; Shin, Sang Woon

    2017-07-01

    Diterpene resin acids (DRAs) are important components of oleoresin and greatly contribute to the defense strategies of conifers against herbivorous insects. In the present study, we determined that DRAs function as insect juvenile hormone (JH) antagonists that interfere with the juvenile hormone-mediated binding of the JH receptor Methoprene-tolerant (Met) and steroid receptor coactivator (SRC). Using a yeast two-hybrid system transformed with Met and SRC from the Indian meal moth Plodia interpunctella, we tested the interfering activity of 3704 plant extracts against JH III-mediated Met-SRC binding. Plant extracts from conifers, especially members of the Pinaceae, exhibited strong interfering activity, and four active interfering DRAs (7α-dehydroabietic acid, 7-oxodehydroabietic acid, dehydroabietic acid, and sandaracopimaric acid) were isolated from roots of the Japanese pine Pinus densiflora. The four isolated DRAs, along with abietic acid, disrupted the juvenile hormone-mediated binding of P. interpunctella Met and SRC, although only 7-oxodehydroabietic acid disrupted larval development. These results demonstrate that DRAs may play a defensive role against herbivorous insects via insect endocrine-disrupting activity.

  7. Accurate determination of 129I, 41Ca and 10Be long-lived radionuclides concentrations in spent resins from the nuclear industry by accelerator mass spectrometry

    International Nuclear Information System (INIS)

    Nottoli-Lepage, E.

    2013-01-01

    Radiological characterization of nuclear waste is essential for the management of storage sites. More particularly, determining the concentration of Long-Lived Radionuclides (LLRN) is fundamental for their long term management. This study focuses on the determination of three LLRN concentrations, i.e. 129 I (T 1/2 = 15.7*10 6 a), 41 Ca (T 1/2 = 9.94*10 4 a) and 10 Be (T 1/2 = 1.387*10 6 a), in ion exchange resins used for primary fluid purification in Pressurized Water Reactors (PWR). To benefit from the Accelerator Mass Spectrometry (AMS) technique allowing to measure extremely low levels of nuclide concentrations, analytical procedures including: 1) sample dissolution; 2) selective and quantitative extraction of the analyte; and, 3) analyte conditioning for AMS measurements, were developed. Applied on spent resin samples collected at a 900 MW PWR, the procedures developed for each studied LLRN allowed their quantitative recovery and their selective extraction from β-γ emitters and isobars. The concentration measurements of the LLRN of interest were then performed on the Accelerator Mass Spectrometry national facility ASTER housed by the Centre Europeen de Recherche et d'Enseignement des Geosciences de l'Environnement (CEREGE, Aix-en-Provence). 129 I, 41 Ca and 10 Be concentrations in spent resins were measured to be about 10 ng/g, 20 pg/g and 4 ng/g of dry resin, respectively. Considering 129 I and 41 Ca, the measured concentrations agree with those assessed from scaling factors established relatively to easily measured gamma emitters ( 137 Cs and 60 Co). For 10 Be, the presented results are significantly different from expected values but are in agreement with previous ICP-MS results. (author) [fr

  8. A novel approach to measure elemental concentrations in cation exchange resins using XRF-scanning technique, and its potential in water pollution studies

    Science.gov (United States)

    Huang, Jyh-Jaan; Lin, Sheng-Chi; Löwemark, Ludvig; Liou, Ya-Hsuan; Chang, Queenie; Chang, Tsun-Kuo; Wei, Kuo-Yen; Croudace, Ian W.

    2016-04-01

    X-ray fluorescence (XRF) core-scanning is a fast, and convenient technique to assess elemental variations for a wide variety of research topics. However, the XRF scanning counts are often considered a semi-quantitative measurement due to possible absorption or scattering caused by down core variability in physical properties. To overcome this problem and extend the applications of XRF-scanning to water pollution studies, we propose to use cation exchange resin (IR-120) as an "elemental carrier", and to analyze the resins using the Itrax-XRF core scanner. The use of resin minimizes the matrix effects during the measurements, and can be employed in the field in great numbers due to its low price. Therefore, the fast, and non-destructive XRF-scanning technique can provide a quick and economical method to analyze environmental pollution via absorption in the resin. Five standard resin samples were scanned by the Itrax-XRF core scanner at different exposure times (1 s, 5 s, 15 s, 30 s, 100 s) to allow the comparisons of scanning counts with the absolute concentrations. The regression lines and correlation coefficients of elements that are generally used in pollution studies (Ca, Ti, Cr, Ni, Cu, Zn, and Pb) were examined for the different exposure times. The result shows that within the test range (from few ppm to thousands ppm), the correlation coefficients are all higher than 0.97, even at the shortest exposure time (1 s). Therefore, we propose to use this method in the field to monitor for example sewage disposal events. The low price of resin, and fast, multi elements and precise XRF-scanning technique provide a viable, cost- and time-effective approach that allows large sample numbers to be processed. In this way, the properties and sources of wastewater pollution can be traced for the purpose of environmental monitoring and environmental forensics.

  9. Synthetic resin-bound truncated Candida antarctica lipase B for production of fatty acid alkyl esters by transesterification of corn and soybean oils with ethanol or butanol.

    Science.gov (United States)

    Hughes, Stephen R; Moser, Bryan R; Robinson, Samantha; Cox, Elby J; Harmsen, Amanda J; Friesen, Jon A; Bischoff, Kenneth M; Jones, Marjorie A; Pinkelman, Rebecca; Bang, Sookie S; Tasaki, Ken; Doll, Kenneth M; Qureshi, Nasib; Liu, Siqing; Saha, Badal C; Jackson, John S; Cotta, Michael A; Rich, Joseph O; Caimi, Paolo

    2012-05-31

    A gene encoding a synthetic truncated Candida antarctica lipase B (CALB) was generated via automated PCR and expressed in Saccharomyces cerevisiae. Western blot analysis detected five truncated CALB variants, suggesting multiple translation starts from the six in-frame ATG codons. The longest open reading frame, which corresponds to amino acids 35-317 of the mature lipase, appeared to be expressed in the greatest amount. The truncated CALB was immobilized on Sepabeads® EC-EP resin and used to produce ethyl and butyl esters from crude corn oil and refined soybean oil. The yield of ethyl esters was 4-fold greater from corn oil than from soybean oil and was 36% and 50% higher, respectively, when compared to a commercially available lipase resin (Novozym 435) using the same substrates. A 5:1 (v/v) ratio of ethanol to corn oil produced 3.7-fold and 8.4-fold greater yields than ratios of 15:1 and 30:1, respectively. With corn oil, butyl ester production was 56% higher than ethyl ester production. Addition of an ionic catalytic resin step prior to the CALB resin increased yields of ethyl esters from corn oil by 53% compared to CALB resin followed by ionic resin. The results suggest resin-bound truncated CALB has potential application in biodiesel production using biocatalysts. Published by Elsevier B.V.

  10. Ion Exchange Study of Some New Copolymer Resins Derived from 8-Hydroxyquinoline-5-sulphonic Acid, Biuret and Formaldehyde

    Directory of Open Access Journals (Sweden)

    P. A. Dhakite

    2011-01-01

    Full Text Available Copolymer resins (8-HQSABF were synthesized by the condensation of 8-hydroxyquinoline-5-sulphonic acid and biuret with formaldehyde in the presence of hydrochloric acid as catalyst, proved to be selective chelation ion exchange copolymer resins for certain metals. Chelation ion exchange properties to these polymers were studied for Cu2+, Cd2+, Co2+ and Zn2+ ions. A batch equilibrium method was employed in the study of the selectivity of the distribution of a given metal ions between the polymer sample and a solution containing the metal ion. The study was carried out over a wide pH range and in a media of various ions strengths. The polymer showed a higher selectivity for Cu2+ ions than for Cd2+, Co2+ and Zn2+ ions. Hence on the basis of above studies these copolymer may be used as semiconductors, surface coating, ion-exchangers, materials for rechargeable battery cell in various electronic industries, plastic materials, elastomers and in boiler plants

  11. A Robust Epoxy Resins @ Stearic Acid-Mg(OH)2 Micronanosheet Superhydrophobic Omnipotent Protective Coating for Real-Life Applications.

    Science.gov (United States)

    Si, Yifan; Guo, Zhiguang; Liu, Weimin

    2016-06-29

    Superhydrophobic coating has extremely high application value and practicability. However, some difficult problems such as weak mechanical strength, the need for expensive toxic reagents, and a complex preparation process are all hard to avoid, and these problems have impeded the superhydrophobic coating's real-life application for a long time. Here, we demonstrate one kind of omnipotent epoxy resins @ stearic acid-Mg(OH)2 superhydrophobic coating via a simple antideposition route and one-step superhydrophobization process. The whole preparation process is facile, and expensive toxic reagents needed. This omnipotent coating can be applied on any solid substrate with great waterproof ability, excellent mechanical stability, and chemical durability, which can be stored in a realistic environment for more than 1 month. More significantly, this superhydrophobic coating also has four protective abilities, antifouling, anticorrosion, anti-icing, and flame-retardancy, to cope with a variety of possible extreme natural environments. Therefore, this omnipotent epoxy resins @ stearic acid-Mg(OH)2 superhydrophobic coating not only satisfies real-life need but also has great application potential in many respects.

  12. Pretreatment on corn stover with low concentration of formic acid.

    Science.gov (United States)

    Xu, Jian; Thomsen, Mette Hedegaard; Thomsen, Anne Belinda

    2009-08-01

    Bioethanol derived from lignocellulosic biomass has the potential to replace gasoline. Cellulose is naturally recalcitrant to enzymatic attack, and it also surrounded by the matrix of xylan and lignin, which enhances the recalcitrance. Therefore, lignocellulosic materials must be pretreated to make the cellulose easily degraded into sugars and further fermented to ethanol. In this work, hydrothermal pretreatment on corn stover at 195 degrees for 15 min with and without lower concentration of formic acid was compared in terms of sugar recoveries and ethanol fermentation. For pretreatment with formic acid, the overall glucan recovery was 89% and pretreatment without formic acid yielded the recovery of 94%. Compared with glucan, xylan was more sensitive to the pretreatment condition. The lowest xylan recovery of 55% was obtained after pretreatment with formic acid and the highest of 75% found following pretreatment without formic acid. Toxicity tests of liquor parts showed that there were no inhibitions found for both pretreatment conditions. After simultaneous saccharification and fermentation (SSF) of the pretreated corn stover with Baker's yeast, the highest ethanol yield of 76.5% of the theoretical was observed from corn stover pretreated at 195 degrees for 15 min with formic acid.

  13. Effect of phytic acid etchant on resin-dentin bonding: Monomer penetration and stability of dentin collagen.

    Science.gov (United States)

    Kong, Kalyan; Hiraishi, Noriko; Nassar, Mohannad; Otsuki, Masayuki; Yiu, Cynthia K Y; Tagami, Junji

    2017-07-01

    Phytic acid (IP6) works well as an etchant in dentin bonding to remove the smear layer due to its acidity and chelating effect. This study compared the etching effect of IP6 with phosphoric acid (PA) and ethylenediaminetetraacetic acid (EDTA) on resin-dentin bond strength, micromorphology of the etched dentin surface and nanoleakage formation along resin-dentin interfaces and compared the protecting effect against collagen degradation. Dentin disks and flat dentin surfaces were obtained from extracted human teeth. Specimens were etched with 35% PA (15s), 0.5M EDTA (30s) or 1% IP6 (30s). The surfaces and longitudinal sections of the etched dentin disks were observed using field emission scanning electron microscope (FE-SEM). An etch-and-rinse adhesive was used to create composite build up-specimens for microtensile bond strength (μTBS) testing and nanoleakage observation. To evaluate the effect on collagen degradation, demineralized bovine root dentin blocks were challenged with bacterial collagenase and then observed under light microscope. PA- and EDTA- treated groups showed significantly lower μTBS when compared to IP6-treated group. PA showed distinct nanoleakage and severe collagen degradation. Only slight nanoleakage was detected in IP6 group. IP6 showed better effect than EDTA in preventing collagen degradation induced by bacterial collagenase. IP6 effectively removed the smear layer and etched dentin, providing high bond strength values and causing minimal nanoleakage and slight collagen degradation. Copyright © 2016 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  14. Highly Concentrated Acetic Acid Poisoning: 400 Cases Reviewed

    Directory of Open Access Journals (Sweden)

    Konstantin Brusin

    2012-12-01

    Full Text Available Background: Caustic substance ingestion is known for causing a wide array of gastrointestinal and systemic complications. In Russia, ingestion of acetic acid is a major problem which annually affects 11.2 per 100,000 individuals. The objective of this study was to report and analyze main complications and outcomes of patients with 70% concentrated acetic acid poisoning. Methods: This was a retrospective study of patients with acetic acid ingestion who were treated at Sverdlovsk Regional Poisoning Treatment Center during 2006 to 2012. GI mucosal injury of each patient was assessed with endoscopy according to Zargar’s scale. Data analysis was performed to analyze the predictors of stricture formation and mortality. Results: A total of 400 patients with median age of 47 yr were included. GI injury grade I was found in 66 cases (16.5%, IIa in 117 (29.3%, IIb in 120 (30%, IIIa in 27 (16.7% and IIIb in 70 (17.5%. 11% of patients developed strictures and overall mortality rate was 21%. Main complications were hemolysis (55%, renal injury (35%, pneumonia (27% and bleeding during the first 3 days (27%. Predictors of mortality were age 60 to 79 years, grade IIIa and IIIb of GI injury, pneumonia, stages “I”, “F” and “L” of kidney damage according to the RIFLE scale and administration of prednisolone. Predictors of stricture formation were ingestion of over 100 mL of acetic acid and grade IIb and IIIa of GI injury. Conclusion: Highly concentrated acetic acid is still frequently ingested in Russia with a high mortality rate. Patients with higher grades of GI injury, pneumonia, renal injury and higher amount of acid ingested should be more carefully monitored as they are more susceptible to develop fatal consequences.          

  15. Esterification of oleic acid in a three-phase, fixed-bed reactor packed with a cation exchange resin catalyst.

    Science.gov (United States)

    Son, Sung Mo; Kimura, Hiroko; Kusakabe, Katsuki

    2011-01-01

    Esterification of oleic acid was performed in a three-phase fixed-bed reactor with a cation exchange resin catalyst (Amberlyst-15) at high temperature, which was varied from 80 to 120 °C. The fatty acid methyl ester (FAME) yields in the fixed-bed reactor were increased with increases in the reaction temperature, methanol flow rate and bed height. Moreover, the FAME yields were higher than those obtained using a batch reactor due to an equilibrium shift toward the product that resulted from continuous evaporation of the produced water. In addition, there was no catalyst deactivation during the esterification of oleic acid. However, addition of sunflower oil to the oleic acid reduced the FAME yield obtained from simultaneous esterification and transesterification. The FAME yield was 97.5% at a reaction temperature of 100 °C in the fixed-bed with a height of 5 cm when the methanol and oleic acid feed rates were 8.6 and 9.0 mL/h, respectively. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. COMPARATIVE STUDY OF THE SHEAR BOND STRENGTH OF COMPOSITE RESIN TO DENTAL ENAMEL CONDITIONED WITH PHOSPHORIC ACID OR Nd: YAG LASER

    Directory of Open Access Journals (Sweden)

    EDUARDO Carlos de Paula

    1997-01-01

    Full Text Available This study has been focused on a comparison between the shear bond strength of a composite resin attached to dental enamel surface, after a 35% phosphoric acid etching and after a Nd:YAG laser irradiation with 165.8 J/cm2 of energy density per pulse. After etching and attaching resin to these surfaces, the specimens were thermocycled and then underwent the shearing bond strength tests at a speed of 5 mm/min. The results achieved, after statistical analysis with Student's t-test, showed that the adhesion was significantly greater in the 35% phosphoric acid treated group than in the group treated with the Nd:YAG laser, thus demonstrating the need for developing new studies to reach the ideal parameters for an effective enamel surface conditioning as well as specific adhesives and composite resins when Nd:YAG laser is used

  17. Effect of diphenyliodonium hexafluorphosphate on resin cements containing different concentrations of ethyl 4-(dimethylamino)benzoate and 2-(dimethylamino)ethyl methacrylate as co-initiators.

    Science.gov (United States)

    Andrade, Kamila Menezes Guedes de; Palialol, Alan Rodrigo; Lancellotti, Ailla C; Aguiar, Flávio Henrique Baggio; Watts, David C; Gonçalves, Luciano Souza; Lima, Adriano Fonseca; Marchi, Giselle Maria

    2016-06-01

    The present study evaluated the influence of diphenyliodonium hexafluorphosphate (DPI) combined with two different amines [ethyl 4-(dimethylamino)benzoate (EDAB) and 2-(dimethylamino)ethyl methacrylate (DMAEMA)] on the properties of model resin cements. A comonomer base containing a 1:1 mass ratio of 2.2-bis[4-(2-hydroxy-3-methacryloxypropoxy)phenyl]propane (bis-GMA) and triethyleneglycol dimethacrylate (TEGDMA) was obtained, after which 1mol% of camphorquinone and 0.1mol% of hydroxyl butyl toluene were added to the comonomer blend. Concentrations of co-initiators varied at 0, 0.5 or 1mol% for DPI and in 1 or 2mol% for amines (DMAEMA or EDAB). Silanated Ba-Al-Si glass (60wt%) was added as filler. The combination of each amine and DPI concentration resulted in 12 formulations, which had the following properties analyzed: degree of conversion (DC), water sorption (Wsp) and solubility (Wsl), flexural strength (FS) and flexural modulus (Ef). Data for DC, FS and Ef were analyzed by two-way ANOVA and Tukey's test (α=0.05) and Wsp and Wsl by Kruskal-Wallis and Dunn tests (α=0.05). EDAB promoted a higher DC than did DMAEMA; however, DPI increased DC for all materials with DMAEMA. The physical properties of resin formulations containing EDAB were significantly better than those of groups with DMAEMA; however, DPI had a positive influence on the chemical and physical properties of the model resin cement containing DMAEMA, especially with higher concentrations of amine. EDAB proved to be more reactive than DMAEMA, being less influenced by DPI. Resins containing a 1:2 CQ/amine ratio had better properties than those with 1:1. Copyright © 2016 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  18. Use of extractive distillation to produce concentrated nitric acid

    International Nuclear Information System (INIS)

    Campbell, P.C.; Griffin, T.P.; Irwin, C.F.

    1981-04-01

    Concentrated nitric acid (> 95 wt %) is needed for the treatment of off-gases from a fuels-reprocessing plant. The production of concentrated nitric acid by means of extractive distillation in the two-pot apparatus was studied to determine the steady-state behavior of the system. Four parameters, EDP volume (V/sub EDP/) and temperature (T/sub EDP/), acid feed rate, and solvent recycle, were independently varied. The major response factors were percent recovery (CPRR) and product purity (CCP). Stage efficiencies also provided information about the system response. Correlations developed for the response parameters are: CPRR = 0.02(V/sub EDP/ - 800 cc) + 53.5; CCP = -0.87 (T/sub EDP/ - 140 0 C) + 81; eta/sub V,EDP/ = 9.1(F/sub feed/ - 11.5 cc/min) - 0.047(V/sub EDP/ - 800 cc) - 2.8(F/sub Mg(NO 3 ) 2 / - 50 cc/min) + 390; and eta/sub L,EDP/ = 1.9(T/sub EDP/ - 140 0 C) + 79. A computer simulation of the process capable of predicting steady-state conditions was developed, but it requires further work

  19. Preparation of a ribonucleic acid-(polyamidoamine)-(zirconia-urea-formaldehyde resin) high-performance liquid affinity chromatographic stationary phase.

    Science.gov (United States)

    Lei, S; Yu, S; Zhao, C

    2001-07-01

    A preparative method for a high-performance liquid affinity chromatographic (HPLAC) stationary phase is described. The 3- to 5-microm nonporous composite spherical microparticles of zirconia and urea-formaldehyde (UF) resin are synthesized through the reaction of zirconyl chloride with hexamethylene tetra-amine and urea, and then it is used as the matrix of the HPLAC stationary phase of which the diameter and structure are determined by scanning electron microscopy. In a methanol medium, the polyamidoamine (PAMAM) starburst dentritic spacer arms are linked with the imido-groups on the surface of the matrix by the Michael addition reaction with methyl acrylate and the amination reaction with ethylene diamine. After repeating these steps in triplets, amine-terminated dentritic spacer arms with a generation of 3 are obtained. The topological structure of the spacer arms is examined by solid-state 13C NMR. The Br-substituted ribonucleic acid (RNA) ligand is obtained by the reaction of liquid bromine with RNA and bonded to the dendritic spacer arms of the matrix in a solution of NaOH (pH 9-11). The binding capacity of RNA is measured by UV spectrophotometry. A new type of stationary phase--RNA-(PAMAM)-(zirconia-UF resin--for HPLAC, which possesses starburst dendritic spacer arms, is synthesized and used for the separation of biological macromolecules.

  20. Can heat treatment procedures of pre-hydrolyzed silane replace hydrofluoric acid in the adhesion of resin cement to feldspathic ceramic?

    Science.gov (United States)

    Cotes, Caroline; de Carvalho, Rodrigo Furtado; Kimpara, Estevão Tomomitsu; Leite, Fabíola Pessoa; Ozcan, Mutlu

    2013-12-01

    To evaluate the influence of heat treatment (HT) procedures of a pre-hydrolyzed silane on bond strength of resin cement to a feldspathic ceramic. Ceramic and composite blocks (N = 30) were divided into six groups (n = 5) and subjected to the following conditioning procedures: G1: 9.6% hydrofluoric acid (HF) for 20 s + silane (RelyX Ceramic Primer, 3M ESPE) + resin cement (Panavia F2.0, Kuraray) (control); G2: HF (20 s) + silane + heat treatment in furnace (HTF) (100°C, 2 min) + resin cement; G3: silane + HTF + resin cement; G4- HF (20 s) + silane + heat treatment with hot air (HTA) (50 ± 5°C for 1 min) + resin cement; G5: silane + HTA + resin cement; G6: silane + resin cement. The microtensile bond strength (MTBS) test was performed using a universal testing machine (1 mm/min). After debonding, the substrate and adherent surfaces were analyzed using a stereomicroscope and SEM to categorize the failure types. The data were statistically evaluated using one-way ANOVA and Tukey's test (5%). The control group (G1) showed no pre-test failures and presented significantly higher mean MTBS (16.01 ± 1.12 MPa) than did other groups (2.63 ± 1.05 to 12.55 ± 1.52 MPa) (p = 0.0001). In the groups where HF was not used, HTF (G3: 12.55 ± 1.52 MPa) showed significantly higher MTBS than did HTA (G5: 2.63 ± 1.05 MPa) (p silane either in a furnace or with the application of hot air cannot replace the use of HF gel for the adhesion of resin cement to feldspathic ceramic. Yet when mean bond strengths and incidence of pre-test failures are considered, furnace heat treatment delivered the second best results after the control group, being considerably better than hot air application.

  1. Characterization of Group V Dubnium Homologs on DGA Extraction Chromatography Resin from Nitric and Hydrofluoric Acid Matrices

    Energy Technology Data Exchange (ETDEWEB)

    Despotopulos, J D; Sudowe, R

    2012-02-21

    somewhere between Nb and Pa. Much more recent studies have examined the properties of Db from HNO{sub 3}/HF matrices, and suggest Db forms complexes similar to those of Pa. Very little experimental work into the behavior of element 114 has been performed. Thermochromatography experiments of three atoms of element 114 indicate that the element 114 is at least as volatile as Hg, At, and element 112. Lead was shown to deposit on gold at temperatures about 1000 C higher than the atoms of element 114. Results indicate a substantially increased stability of element 114. No liquid phase studies of element 114 or its homologs (Pb, Sn, Ge) or pseudo-homologs (Hg, Cd) have been performed. Theoretical predictions indicate that element 114 is should have a much more stable +2 oxidation state and neutral state than Pb, which would result in element 114 being less reactive and less metallic than Pb. The relativistic effects on the 7p{sub 1/2} electrons are predicted to cause a diagonal relationship to be introduced into the periodic table. Therefore, 114{sup 2+} is expected to behave as if it were somewhere between Hg{sup 2+}, Cd{sup 2+}, and Pb{sup 2+}. In this work two commercially available extraction chromatography resins are evaluated, one for the separation of Db homologs and pseudo?homologs from each other as well as from potential interfering elements such as Group IV Rf homologs and actinides, and the other for separation of element 114 homologs. One resin, Eichrom's DGA resin, contains a N,N,N',N'-tetra-n-octyldiglycolamide extractant, which separates analytes based on both size and charge characteristics of the solvated metal species, coated on an inert support. The DGA resin was examined for Db chemical systems, and shows a high degree of selectivity for tri-, tetra-, and hexavalent metal ions in multiple acid matrices with fast kinetics. The other resin, Eichrom's Pb resin, contains a di-t-butylcyclohexano 18-crown-6 extractant with isodecanol solvent

  2. Method for digesting spent ion exchange resins and recovering actinides therefrom using microwave radiation

    Science.gov (United States)

    Maxwell, III, Sherrod L.; Nichols, Sheldon T.

    1999-01-01

    The present invention relates to methods for digesting diphosphonic acid substituted cation exchange resins that have become loaded with actinides, rare earth metals, or heavy metals, in a way that allows for downstream chromatographic analysis of the adsorbed species without damage to or inadequate elution from the downstream chromatographic resins. The methods of the present invention involve contacting the loaded diphosphonic acid resin with concentrated oxidizing acid in a closed vessel, and irradiating this mixture with microwave radiation. This efficiently increases the temperature of the mixture to a level suitable for digestion of the resin without the use of dehydrating acids that can damage downstream analytical resins. In order to ensure more complete digestion, the irradiated mixture can be mixed with hydrogen peroxide or other oxidant, and reirradiated with microwave radiation.

  3. Kinetic, equilibrium and thermodynamic studies on sorption of uranium and thorium from aqueous solutions by a selective impregnated resin containing carminic acid

    Energy Technology Data Exchange (ETDEWEB)

    Rahmani-Sani, Abolfazl [Wastewater Division, Faculty of Health, Sabzevar University of Medical Sciences, PO Box 319, Sabzevar (Iran, Islamic Republic of); Hosseini-Bandegharaei, Ahmad, E-mail: ahoseinib@yahoo.com [Wastewater Division, Faculty of Health, Sabzevar University of Medical Sciences, PO Box 319, Sabzevar (Iran, Islamic Republic of); Department of Engineering, Kashmar Branch, Islamic Azad University, PO Box 161, Kashmar (Iran, Islamic Republic of); Hosseini, Seyyed-Hossein [Department of Engineering, Kashmar Branch, Islamic Azad University, PO Box 161, Kashmar (Iran, Islamic Republic of); Kharghani, Keivan [Water Division, Department of Engineering, Torbat-e-Hydarieh Branch, Islamic Azad University, PO Box 121, Torbat-e-Hydarieh (Iran, Islamic Republic of); Zarei, Hossein [Department of Engineering, Kashmar Branch, Islamic Azad University, PO Box 161, Kashmar (Iran, Islamic Republic of); Rastegar, Ayoob [Wastewater Division, Faculty of Health, Sabzevar University of Medical Sciences, PO Box 319, Sabzevar (Iran, Islamic Republic of); Department of Engineering, Kashmar Branch, Islamic Azad University, PO Box 161, Kashmar (Iran, Islamic Republic of)

    2015-04-09

    Highlights: • The objective of the study is to investigate the potential application of a selective EIR for sorption of U(VI) and Th(IV) ions. • The effects of several physiochemical parameters were investigated. • The sorption kinetics and sorption isotherms were used to explain the sorption mechanism. • The thermodynamic studies showed the feasibility of sorption process. • The EIR beads showed a great potential for effective removal of U(VI) and Th(IV) ions. - Abstract: In this work, the removal of uranium and thorium ions from aqueous solutions was studied by solid–liquid extraction using an advantageous extractant-impregnated resin (EIR) prepared by loading carminic acid (CA) onto Amberlite XAD-16 resin beads. Batch sorption experiments using CA/XAD-16 beads for the removal of U(VI) and Th(IV) ions were carried out as a function of several parameters, like equilibration time, metal ion concentration, etc. The equilibrium data obtained from the sorption experiments were adjusted to the Langmuir isotherm model and the calculated maximum sorption capacities in terms of monolayer sorption were in agreement with those obtained from the experiments. The experimental data on the sorption behavior of both metal ions onto the EIR beads fitted well in both Bangham and intra-particle diffusion kinetic models, indicating that the intra-particle diffusion is the rate-controlling step. The thermodynamic studies at different temperatures revealed the feasibility and the spontaneous nature of the sorption process for both uranium and thorium ions.

  4. Kinetic, equilibrium and thermodynamic studies on sorption of uranium and thorium from aqueous solutions by a selective impregnated resin containing carminic acid

    International Nuclear Information System (INIS)

    Rahmani-Sani, Abolfazl; Hosseini-Bandegharaei, Ahmad; Hosseini, Seyyed-Hossein; Kharghani, Keivan; Zarei, Hossein; Rastegar, Ayoob

    2015-01-01

    Highlights: • The objective of the study is to investigate the potential application of a selective EIR for sorption of U(VI) and Th(IV) ions. • The effects of several physiochemical parameters were investigated. • The sorption kinetics and sorption isotherms were used to explain the sorption mechanism. • The thermodynamic studies showed the feasibility of sorption process. • The EIR beads showed a great potential for effective removal of U(VI) and Th(IV) ions. - Abstract: In this work, the removal of uranium and thorium ions from aqueous solutions was studied by solid–liquid extraction using an advantageous extractant-impregnated resin (EIR) prepared by loading carminic acid (CA) onto Amberlite XAD-16 resin beads. Batch sorption experiments using CA/XAD-16 beads for the removal of U(VI) and Th(IV) ions were carried out as a function of several parameters, like equilibration time, metal ion concentration, etc. The equilibrium data obtained from the sorption experiments were adjusted to the Langmuir isotherm model and the calculated maximum sorption capacities in terms of monolayer sorption were in agreement with those obtained from the experiments. The experimental data on the sorption behavior of both metal ions onto the EIR beads fitted well in both Bangham and intra-particle diffusion kinetic models, indicating that the intra-particle diffusion is the rate-controlling step. The thermodynamic studies at different temperatures revealed the feasibility and the spontaneous nature of the sorption process for both uranium and thorium ions

  5. SOLVENT EFFECTS ON THE HYDRATION OF CYCLOHEXENE CATALYZED BY A STRONG ACID ION-EXCHANGE RESIN .3. EFFECT OF SULFOLANE ON THE EQUILIBRIUM CONVERSION

    NARCIS (Netherlands)

    PANNEMAN, HJ; BEENACKERS, AACM

    The liquid-phase hydration of cyclohexene, a pseudo-first-order reversible reaction catalyzed by a strong acid ion-exchange resin, was investigated in solvent mixtures of water and sulfolane. Macroporous Amberlite XE 307 was used because of its superior catalytic activity. Chemical equilibrium

  6. LC/ESI-MS/MS method for determination of salivary eicosapentaenoic acid concentration to arachidonic acid concentration ratio.

    Science.gov (United States)

    Ogawa, Shoujiro; Tomaru, Koki; Matsumoto, Nagisa; Watanabe, Shui; Higashi, Tatsuya

    2016-01-01

    A simple liquid chromatography/electrospray ionization-tandem mass spectrometry (LC/ESI-MS/MS) method for determination of the eicosapentaenoic acid (EPA) concentration to arachidonic acid (AA) concentration ratio in human saliva has been developed. The EPA/AA ratio in serum or plasma is widely recognized as a useful indicator in identifying the risk of cardiovascular disease, especially atherosclerosis. The salivary EPA/AA ratio is expected to be a convenient alternative to the serum or plasma EPA/AA ratio, because saliva offers the advantages of easy and noninvasive sampling. The saliva was deproteinized with acetonitrile, purified using an Oasis HLB cartridge, and derivatized with 1-[(4-dimethylaminophenyl)carbonyl]piperazine (DAPPZ). The derivatized EPA and AA were subjected to LC/ESI-MS/MS, and the EPA/AA ratio was determined using the selected reaction monitoring mode. The DAPPZ-derivatization increased the ESI sensitivity by 100- and 300-fold for EPA and AA, respectively, and enabled the detection of trace fatty acids in saliva using a 200 μL sample. The assay reproducibility was satisfactory (relative standard deviation, <5.0%). The method was successfully applied to the measurement of the salivary EPA/AA ratios of healthy Japanese subjects and their changes owing to the supplementation of EPA. Copyright © 2015 John Wiley & Sons, Ltd.

  7. Properties of the Carboxylate ion exchange resins

    International Nuclear Information System (INIS)

    Allard, Bert; Dario, Maarten; Boren, Hans; Torstenfelt, Boerje; Puigdomenech, Ignasi; Johansson, Claes

    2002-09-01

    Weakly acidic, carboxylic resin has been selected, together with strong base anion resins, for water purification at the Forsmark 1 and 2 reactors. For the strong (but not the weak) ion exchange resin the Nuclear Power Inspectorate has given permission to dispose the spent resins in the SFR 1 (the Final Repository for Radioactive Operational Waste). This report gives a review of the carboxylic resins and comes to the conclusion that the resins are very stable and that there should not exist any risks for increased leaching of radionuclides from SFR 1 if these resins are disposed (compared to the strong resins)

  8. Dietary Sodium Modifies Serum Uric Acid Concentrations in Humans.

    Science.gov (United States)

    Todd, Alwyn S; Walker, Robert J; MacGinley, Robert J; Kelly, Jaimon; Merriman, Tony R; Major, Tanya J; Johnson, Richard J

    2017-11-06

    Subjects with hypertension are frequently obese or insulin resistant, both conditions in which hyperuricemia is common. Obese and insulin-resistant subjects are also known to have blood pressure that is more sensitive to changes in dietary sodium intake. Whether hyperuricemia is a resulting consequence, moderating or contributing factor to the development of hypertension has not been fully evaluated and very few studies have reported interactions between sodium intake and serum uric acid. We performed further analysis of our randomized controlled clinical trials (Australian New Zealand Clinical Trials Registry #12609000161224 and #12609000292279) designed to assess the effects of modifying sodium intake on concentrations of serum markers, including uric acid. Uric acid and other variables (including blood pressure, renin, and aldosterone) were measured at baseline and 4 weeks following the commencement of low (60 mmol/day), moderate (150 mmol/day), and high (200-250 mmol/day) dietary sodium intake. The median aldosterone-to-renin ratio was 1.90 [pg/ml]/[pg/ml] (range 0.10-11.04). Serum uric acid fell significantly in both the moderate and high interventions compared to the low sodium intervention. This pattern of response occurred when all subjects were analyzed, and when normotensive or hypertensive subjects were analyzed alone. Although previously reported in hypertensive subjects, these data provide evidence in normotensive subjects of an interaction between dietary sodium intake and serum uric acid. As this interaction is present in the absence of hypertension, it is possible it could play a role in hypertension development, and will need to be considered in future trials of dietary sodium intake. The trials were registered with the Australian and New Zealand Clinical Trials Registry as ACTRN12609000161224 and ACTRN1260. © American Journal of Hypertension, Ltd 2017. All rights reserved. For Permissions, please email: journals.permissions@oup.com

  9. Effect of the cross-linking silane concentration in a novel silane system on bonding resin-composite cement

    NARCIS (Netherlands)

    Matinlinna, Jukka; Ozcan, Mutlu; Lassila, Lippo; Kalk, Warner; Vallittu, Pekka

    2008-01-01

    Objective. Four experimental blends of an organo-functional silane monomer with a non-functional cross-linking silane monomer (a novel silane system) were evaluated as adhesion promoters in an experiment in which a resin-composite cement was bonded to silica-coated titanium. Material and Methods.

  10. Catalytic Upgrading of bio-oil using 1-octene and 1-butanol over sulfonic acid resin catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Zhijun; Wang, Qingwen; Tripathi, Prabhat; Pittman, Charles U.

    2011-02-04

    Raw bio-oil from fast pyrolysis of biomass must be refined before it can be used as a transporation fuel, a petroleum refinery feed or for many other fuel uses. Raw bio-oil was upgraded with the neat model olefin, 1-octene, and with 1-octene/1-butanol mixtures over sulfonic acid resin catalysts frin 80 to 150 degrees celisus in order to simultaneously lower water content and acidity and to increase hydrophobicity and heating value. Phase separation and coke formation were key factors limiting the reaction rate during upgrading with neat 1-octene although octanols were formed by 1-octene hydration along with small amounts of octyl acetates and ethers. GC-MS analysis confirmed that olefin hydration, carboxylic acid esterification, acetal formation from aldehydes and ketones and O- and C-alkylations of phenolic compounds occurred simultaneously during upgrading with 1-octene/1-butanol mixtures. Addition of 1-butanol increased olefin conversion dramatically be reducing mass transfer restraints and serving as a cosolvent or emulsifying agent. It also reacted with carboxylic acids and aldehydes/ketones to form esters, and acetals, respectively, while also serving to stabilize bio-oil during heating. 1-Butanol addition also protected the catalysts, increasing catalyst lifetime and reducing or eliminationg coking. Upgrading sharply increased ester content and decreased the amounts of levoglucosan, polyhydric alcohols and organic acids. Upgrading lowered acidity (pH value rise from 2.5 to >3.0), removed the uppleasant ordor and increased hydrocarbon solubility. Water content decreased from 37.2% to < 7.5% dramatically and calorific value increased from 12.6 MJ kg to about 30.0 MJ kg.

  11. Consequences of enamel preparation with sodium hypochlorite, polyacrylic and phosphoric acids for the bonding of brackets with resin-modified glass ionomer cements

    OpenAIRE

    Trindade, Alessandra Marques; Pereira, Tatiana Bahia Junqueira; Smith Neto, Perrin; Horta, Martinho Campolina Rebello; Pithon, Matheus Melo; Akaki, Emílio; Oliveira, Dauro Douglas

    2013-01-01

    The aim of this study was to evaluate the effects of deproteinization with 5.25% sodium hypochlorite (NaOCl) prior to enamel conditioning with 10% polyacrylic acid (PAA) and 35% phosphoric acid (PA) on the bond strength (BS) of brackets bonded with resin-modified glass ionomer cement (RMGIC). One hundred human premolars extracted for orthodontic reasons were divided into 5 groups (n = 20 in each group): G1 (control), enamel conditioning with PA, application of adhesive and bonding of brackets...

  12. Effect Of Sodium Hypochlorite And Peracetic Acid On The Surface Roughness Of Acrylic Resin Polymerized By Heated Water For Short And Long Cycles.

    OpenAIRE

    Sczepanski, Felipe; Sczepanski, Claudia Roberta Brunnquell; Berger, Sandrine Bittencourt; Consani, Rafael Leonardo Xediek; Gonini-Júnior, Alcides; Guiraldo, Ricardo Danil

    2015-01-01

    Objective: To evaluate the surface roughness of acrylic resin submitted to chemical disinfection via 1% sodium hypochlorite (NaClO) or 1% peracetic acid (C2H4O3). Materials and Methods: The disc-shaped resin specimens (30 mm diameter ×4 mm height) were polymerized by heated water using two cycles (short cycle: 1 h at 74°C and 30 min at 100°C; conventional long cycle: 9 h at 74°C). The release of substances by these specimens in water solution was also quantified. Specimens were fabricated, di...

  13. Porcine milk oligosaccharides and sialic acid concentrations vary throughout lactation

    Directory of Open Access Journals (Sweden)

    Austin T Mudd

    2016-09-01

    Full Text Available Background: Milk oligosaccharides (OS are bioactive components known to influence neonatal development. These compounds have specific physiological functions acting as prebiotics, immune system modulators, and enhancing intestine and brain development. Objectives: The pig is a commonly used model for studying human nutrition, and there is interest in characterizing and quantifying OS composition of porcine milk across lactation. In this study, we hypothesized that OS and sialic acid (SA composition of porcine milk would be influenced by stage of lactation. Methods: Up to 250 ml of milk was collected from 7 sows at each of three time points: d 0 (colostrum, d 7-9 (mature, and d 17-19 (weaning. Colostrum was collected within 6 h of farrowing and three-day intervals were used for mature and weaning milk to ensure representative sampling. Milk samples were analyzed for OS profiles by Nano LC Chip QTOF MS, OS concentrations via HPAEC-PAD, and SA (total and free was assessed by enzymatic reaction fluorescence detection.Results: Sixty unique OS were identified in porcine milk. Neutral OS were the most abundant at each lactation stage (69-81%, followed by acidic-sialylated OS (16-29% and neutral-fucosylated OS (2-4%. As lactation progressed, acidic OS decreased (P < 0.05, whereas neutral-fucosylated and neutral OS increased (P < 0.05 throughout lactation. Six OS were present in all samples analyzed across lactation (LDFH-I, 2´-FL, LNFP-I, LNnH, 3-Hex, 3´-SL, while LDFT was present only in colostrum samples. Analysis of individual OS concentrations indicated differences (P < 0.05 between days 0 and 7. Conversely, between days 7 and 18, OS concentrations remained stable with only LNnH and LNDFH-I decreasing (P < 0.05 over this period. Analysis of free SA indicated a decrease (P < 0.05 as lactation progressed, while bound and total SA increased (P < 0.05 across lactation. Conclusions: The present data suggest that while porcine milk OS profiles and

  14. Effect of experimental acid/base conditioner on microtensile bond strength of 4-META/MMA-TBB resin to dentin after long-term water immersion.

    Science.gov (United States)

    Soeno, Kohyoh; Taira, Yohsuke; Ito, Shuichi

    2012-01-01

    An experimental conditioner (Exp), which was an aqueous solution of 10% ascorbic acid and 5% ferric chloride, was prepared in this study. This study evaluated the effect of Exp on the microtensile bond strength between a self-curing resin and dentin after long-term water immersion. Flat human dentin surfaces were sequentially pretreated with 40% phosphoric acid, 10% sodium hypochlorite, and Exp. Surface pretreatment with an aqueous solution of 10% citric and 3% ferric chloride (10-3) was used as a control. Composite resin rods were bonded to pretreated dentin surfaces using 4-META/MMA-TBB resin. Microtensile bond strengths were evaluated after water immersion at 24 h, 12 months, 24 months, and 36 months. At each immersion period, the bond strength of Exp was significantly higher than that of 10-3. After 36 months, Exp showed no significant decrease in microtensile bond strength, but 10-3 showed significant reductions. Pretreatment with experimental acid/base conditioner markedly improved the bonding durability of 4-META/MMA-TBB resin to human dentin when compared against the conventional 10-3 treatment.

  15. The Effect of Temperature and Acid Concentration on Corrosion of Low Carbon Steel in Hydrochloric Acid Media

    OpenAIRE

    Anees A. Khadom; Aprael S. Yaro; Abdul A.H. Kadum; Ahmed S. AlTaie; Ahmed Y. Musa

    2009-01-01

    Problem statement: The effect of different temperatures and acid concentrations on the corrosion of low carbon steel in hydrochloric acid were addressed in this study. Approach: The effect of temperature was explained by application of Arrhenius equation and transition state theory, while the acid concentration effect was explained using reaction kinetic equations. The combined effect of temperature and acid concentration then modeled using a nonlinear regression method. Results: A detail of ...

  16. Preparation and characterization of anion exchange resin decorated with magnetite nanoparticles for removal of p-toluic acid from aqueous solution

    Science.gov (United States)

    Davarpanah, Morteza; Ahmadpour, Ali; Rohani Bastami, Tahereh

    2015-02-01

    Polystyrene resin was covalently functionalized with diethanolamine and then decorated with magnetite nanoparticles by a novel and simple co-precipitation method using iron(II) sulfate as precursor. The products were characterized by Fourier transform infrared spectroscopy, elemental analysis, X-ray diffraction, Mössbauer spectroscopy, field-emission scanning electron microscopy and vibrating sample magnetometer. Adsorption of p-toluic acid (p-TA) onto magnetite-decorated polystyrene (MAG-PS) was studied and compared with that of diethanolamine-functionalized polystyrene and a commercial anion exchange resin. Results showed that the magnetite nanoparticles with an average size of 20.4 nm were successfully formed on the surface of polystyrene resin, and MAG-PS was exhibited high affinity for the removal of p-TA.

  17. Biocatalytic Synthesis of Epoxy Resins from Fatty Acids as a Versatile Route for the Formation of Polymer Thermosets with Tunable Properties.

    Science.gov (United States)

    Torron, Susana; Semlitsch, Stefan; Martinelle, Mats; Johansson, Mats

    2016-12-12

    The work herein presented describes the synthesis and polymerization of series of bio-based epoxy resins prepared through lipase catalyzed transesterification. The epoxy-functional polyester resins with various architectures (linear, tri-branched, and tetra-branched) were synthesized through condensation of fatty acids derived from epoxidized soybean oil and linseed oil with three different hydroxyl cores under bulk conditions. The selectivity of the lipases toward esterification/transesterification reactions allowed the formation of macromers with up to 12 epoxides in the backbone. The high degree of functionality of the resins resulted in polymer thermosets with T g values ranging from -25 to over 100 °C prepared through cationic polymerization. The determining parameters of the synthesis and the mechanism for the formation of the species were determined through kinetic studies by 1 H NMR, SEC, and molecular modeling studies. The correlation between macromer structure and thermoset properties was studied through real-time FTIR measurements, DSC, and DMA.

  18. Polyaspartic Acid Concentration Controls the Rate of Calcium Phosphate Nanorod Formation in High Concentration Systems

    Energy Technology Data Exchange (ETDEWEB)

    Krogstad, Daniel V. [Biosystems and; Wang, Dongbo [Biosystems and; Lin-Gibson, Sheng [Biosystems and

    2017-08-31

    Polyelectrolytes are known to greatly affect calcium phosphate (CaP) mineralization. The reaction kinetics as well as the CaP phase, morphology and aggregation state depend on the relative concentrations of the polyelectrolyte and the inorganic ions in a complex, nonlinear manner. This study examines the structural evolution and kinetics of polyaspartic acid (pAsp) directed CaP mineralization at high concentrations of polyelectrolytes, calcium, and total phosphate (19–30 mg/mL pAsp, 50–100 mM Ca2+, Ca/P = 2). Using a novel combination of characterization techniques including cryogenic transmission electron microscopy (cryo-TEM), spectrophotometry, X-ray total scattering pair distribution function analysis, and attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), it was determined that the CaP mineralization occurred over four transition steps. The steps include the formation of aggregates of pAsp stabilized CaP spherical nanoparticles (sNP), crystallization of sNP, oriented attachment of the sNP into nanorods, and further crystallization of the nanorods. The intermediate aggregate sizes and the reaction kinetics were found to be highly polymer concentration dependent while the sizes of the particles were not concentration dependent. This study demonstrates the complex role of pAsp in controlling the mechanism as well as the kinetics of CaP mineralization.

  19. Ion exchange resin fouling of molybdenum in recovery uranium processess

    International Nuclear Information System (INIS)

    Zhang Guowei; Zhao Guirong

    1990-09-01

    The relationship between anion exchange resin fouling and molybdic acid polymerization was studied. By using potentiometer titration and laser-Raman spectroscopy the relationship of molybdic acid polymerization and the pH value of solution or the molybdenum concentration was determined. It was shown that as the concentration of initial molybdenum in solution decreases from 0.2 mol/L to 0.5 mmol/L, the pH value of starting polymerization decreased from 6.5 to 4.5. The experimental results show that the fouling of 201 x 7 resin in the acidic solution is mainly caused by the adsorbing of Mo 3 O 26 4- ion and occupying the exchange radical site of the resin. Under the leaching conditions the molybdenum and phosphate existing in the leaching liquor can form 12-molybdo-phosphate ion. It also leads to resin fouling. The molybdenum on the fouled resin can synergically be desorbed by mixed desorbents containing ammonium hydroxide and ammonium sulfate. The desorbed resin can be used for uranium adsorption and the desorbed molybdenum can be recovered by ion exchange method

  20. Quantitative analysis of PMR-15 polyimide resin by HPLC

    Science.gov (United States)

    Roberts, Gary D.; Lauver, Richard W.

    1987-01-01

    The concentration of individual components and of total solids of 50 wt pct PMR-15 resin solutions was determined using reverse-phase HPLC to within + or - 8 percent accuracy. Acid impurities, the major source of impurities in 3,3', 4,4'-benzophenonetetracarboxylic acid (BTDE), were eliminated by recrystallizing the BTDE prior to esterification. Triester formation was not a problem because of the high rate of esterification of the anhydride relative to that of the carboxylic acid. Aging of PMR-15 resin solutions resulted in gradual formation of the mononadimide and bisnadimide of 4,4'-methylenedianiline, with the BTDE concentration remaining constant. Similar chemical reactions occurred at a reduced rate in dried films of PMR-15 resin.

  1. 21 CFR 146.148 - Reduced acid frozen concentrated orange juice.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Reduced acid frozen concentrated orange juice. 146... Canned Fruit Juices and Beverages § 146.148 Reduced acid frozen concentrated orange juice. (a) Reduced acid frozen concentrated orange juice is the food that complies with the requirements for composition...

  2. High Performance Fatty Acid-Based Vinyl Ester Resin for Liquid Molding

    National Research Council Canada - National Science Library

    Geng, Xing; La Scala, John J; Sands, James M; Palmese, Guiseppe R

    2007-01-01

    ...% compared to 40-60 wt% associated with commercial products. In addition, fatty acid-based monomers can bring about other benefits like higher toughness, lower exothermal heat and low volume shrinkage...

  3. Preparation and characterization of anion exchange resin decorated with magnetite nanoparticles for removal of p-toluic acid from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Davarpanah, Morteza, E-mail: Davarpanah.morteza@gmail.com; Ahmadpour, Ali; Rohani Bastami, Tahereh

    2015-02-01

    Polystyrene resin was covalently functionalized with diethanolamine and then decorated with magnetite nanoparticles by a novel and simple co-precipitation method using iron(II) sulfate as precursor. The products were characterized by Fourier transform infrared spectroscopy, elemental analysis, X-ray diffraction, Mössbauer spectroscopy, field-emission scanning electron microscopy and vibrating sample magnetometer. Adsorption of p-toluic acid (p-TA) onto magnetite-decorated polystyrene (MAG-PS) was studied and compared with that of diethanolamine-functionalized polystyrene and a commercial anion exchange resin. Results showed that the magnetite nanoparticles with an average size of 20.4 nm were successfully formed on the surface of polystyrene resin, and MAG-PS was exhibited high affinity for the removal of p-TA. - Highlights: • .Polystyrene resin was covalently functionalized with diethanolamine. • .The functionalized adsorbents were decorated with magnetite nanoparticles (∼20 nm). • .Proposed magnetization procedure was high-efficient and relatively simple. • .Magnetic adsorbent was presented high affinity for removal of p-toluic acid.

  4. In Vitro Comparison of Compressive and Tensile Strengths of Acrylic Resins Reinforced by Silver Nanoparticles at 2% and 0.2% Concentrations

    Directory of Open Access Journals (Sweden)

    Tahereh Ghaffari

    2014-12-01

    Full Text Available Background and aims. Polymethyl methacrylate, PMMA, is widely used in prosthodontics for fabrication of removable prostheses. This study was undertaken to investigate the effect of adding silver nanoparticles (AgNPs to PMMA at 2% and 0.2% concentrations on compressive and tensile strengths of PMMA. Materials and methods. The silver nanoparticles were mixed with heat-cured acrylic resin in an amalgamator in two groups at 0.2 and 2 wt% of AgNPs. Eighteen 2×20×200-mm samples were prepared for tensile strength test, 12 samples containing silver nanoparticle and 6 samples for the control group. Another 18 cylindrical 25×38-mm samples were prepared for compressive strength test. Scanning electron microscopy was used to verify homogeneous distribution of particles. The powder was manually mixed with a resin monomer and then the mixture was properly blended. Before curing, the paste was packed into steel molds. After curing, the specimens were removed from the molds. One-way ANOVA was used for statistical analysis, followed by multiple comparison test (Scheffé’s test. Results. This study showed that the mean compressive strength of PMMA reinforced with AgNPs was significantly higher than that of the unmodified PMMA (P<0.05. It was not statistically different between the two groups reinforced with AgNPs. The tensile strength was not significantly different between the 0.2% group and unmodified PMMA and it decreased significantly after incorporation of 2% AgNPs (P<0.05. Conclusion. Based on the results and the desirable effect of nanoparticles of silver on improvement of compressive strength of PMMA, use of this material with proper concentration in the palatal area of maxillary acrylic resin dentures is recommended.

  5. In Vitro Comparison of Compressive and Tensile Strengths ofAcrylic Resins Reinforced by Silver Nanoparticles at 2% and0.2% Concentrations.

    Science.gov (United States)

    Ghaffari, Tahereh; Hamedirad, Fahimeh; Ezzati, Baharak

    2014-01-01

    Background and aims. Polymethyl methacrylate, PMMA, is widely used in prosthodontics for fabrication of removable prostheses. This study was undertaken to investigate the effect of adding silver nanoparticles (AgNPs) to PMMA at 2% and 0.2% concentrations on compressive and tensile strengths of PMMA. Materials and methods. The silver nanoparticles were mixed with heat-cured acrylic resin in an amalgamator in two groups at 0.2 and 2 wt% of AgNPs. Eighteen 2×20×200-mm samples were prepared for tensile strength test, 12 samples containing silver nanoparticle and 6 samples for the control group. Another 18 cylindrical 25×38-mm samples were prepared for compressive strength test. Scanning electron microscopy was used to verify homogeneous distribution of particles. The powder was manually mixed with a resin monomer and then the mixture was properly blended. Before curing, the paste was packed into steel molds. After curing, the specimens were removed from the molds. One-way ANOVA was used for statistical analysis, followed by multiple comparison test (Scheffé's test). Results. This study showed that the mean compressive strength of PMMA reinforced with AgNPs was significantly higher than that of the unmodified PMMA (Pstatistically different between the two groups reinforced with AgNPs. The tensile strength was not significantly different between the 0.2% group and unmodified PMMA and it de-creased significantly after incorporation of 2% AgNPs (P<0.05). Conclusion. Based on the results and the desirable effect of nanoparticles of silver on improvement of compressive strength of PMMA, use of this material with proper concentration in the palatal area of maxillary acrylic resin dentures is recommended.

  6. Ion-exclusion chromatographic behavior of aliphatic carboxylic acids and benzenecarboxylic acids on a sulfonated styrene--divinylbenzene co-polymer resin column with sulfuric acid containing various alcohols as eluent.

    Science.gov (United States)

    Ohta, Kazutoku; Towata, Atsuya; Ohashi, Masayoshi

    2003-05-16

    The addition of C1-C7 alcohols (methanol, ethanol, propanol, butanol, heptanol, hexanol and heptanol) to dilute sulfuric acid as eluent in ion-exclusion chromatography using a highly sulfonated styrene-divinylbenzene co-polymer resin (TSKgel SCX) in the H+ form as the stationary phase was carried out for the simultaneous separations of both (a) C1-C7 aliphatic carboxylic acids (formic, acetic, propionic, isobutyric, butyric, isovaleric, valeric, 2-methylvaleric, isocaproic, caproic, 2,2-dimethyl-n-valeric, 2-methylhexanoic, 5-methylhexanoic and heptanoic acids) and (b) benzenecarboxylic acids (pyromellitic, hemimellitic, trimellitic, o-phthalic, m-phthalic, p-phthalic, benzoic and salicylic acids and phenol). Heptanol was the most effective modifier in ion-exclusion chromatography for the improvement of peak shapes and a reduction in retention volumes for higher aliphatic carboxylic acids and benzenecarboxylic acids. Excellent simultaneous separation and relatively highly sensitive conductimetric detection for these C1-C7 aliphatic carboxylic acids were achieved on the TSKgel SCX column (150 x 6 mm I.D.) in 30 min using 0.5 mM sulfuric acid containing 0.025% heptanol as eluent. Excellent simultaneous separation and highly sensitive UV detection at 200 nm for these benzenecarboxylic acids were also achieved on the TSKgel SCX column in 30 min using 5 mM sulfuric acid containing 0.075% heptanol as eluent.

  7. Color Change of Sudan III against Concentrated Sulfuric Acid in Acetonitrile and Quantification for a Small Amount of Concentrated Sulfuric Acid.

    Science.gov (United States)

    Sakurai, Takao; Kurata, Shoji; Ogino, Kenji

    2016-01-01

    The color-changing phenomenon of hydrophobic bisazo dye, Sudan III in an acetonitrile solution against the addition of concentrated sulfuric acid has been discovered and the chromic properties investigated. Based on observations, a novel quantification method of concentrated sulfuric acid has been developed. Sudan III changes its color from orange to blue against a small volume of sulfuric acid, and the acetonitrile solution of Sudan III is the most suitable for observing the color-change phenomenon. (1)H-NMR and UV-Vis spectroscopic studies showed that the color-change mechanism of Sudan III against sulfuric acid is due to the protonation of the dye by sulfuric acid. This phenomenon is applicable to the quantification of concentrated sulfuric acid by introducing the Hammett acidity function. The proposed method requires only a small amount of the sample, 0.04 mL, and enables rapid quantification.

  8. Glucose-lowering effects and mechanisms of the bile acid-sequestering resin sevelamer

    DEFF Research Database (Denmark)

    Brønden, Andreas; Mikkelsen, Kristian; Sonne, David P

    2018-01-01

    and mechanism(s) of sevelamer in patients with type 2 diabetes. MATERIALS AND METHODS: In this double-blinded randomized controlled trial, we randomized 30 patients with type 2 diabetes to sevelamer (n=20) or placebo (n=10). Participants were subjected to standardized 4-hour liquid meal tests at baseline...... synthesis of bile acids, a shift towards a more hydrophilic bile acid pool and increased lipogenesis. No glucagon-like peptide-1-mediated effects on insulin, glucagon or gastric emptying were evident, which point to limited contribution of this incretin hormone to the glucose-lowering effect of sevelamer...

  9. Metabolic Syndrome, Alcohol Consumption and Genetic Factors Are Associated with Serum Uric Acid Concentration

    OpenAIRE

    Stibůrková, Blanka; Pavlíková, Markéta; Sokolová, Jitka; Kožich, Viktor

    2014-01-01

    Objective Uric acid is the end product of purine metabolism in humans, and increased serum uric acid concentrations lead to gout. The objective of the current study was to identify factors that are independently associated with serum uric acid concentrations in a cohort of Czech control individuals. Methods The cohort consisted of 589 healthy subjects aged 18–65 years. We studied the associations between the serum uric acid concentration and the following: (i) demographic, anthropometric and ...

  10. Immobilization of α-amylase and amyloglucosidase onto ion-exchange resin beads and hydrolysis of natural starch at high concentration.

    Science.gov (United States)

    Gupta, Kapish; Jana, Asim Kumar; Kumar, Sandeep; Maiti, Mithu

    2013-11-01

    α-Amylase was immobilized on Dowex MAC-3 with 88 % yield and amyloglucosidase on Amberlite IRA-400 ion-exchange resin beads with 54 % yield by adsorption process. Immobilized enzymes were characterized to measure the kinetic parameters and optimal operational parameters. Optimum substrate concentration and temperature were higher for immobilized enzymes. The thermal stability of the enzymes enhanced after the immobilization. Immobilized enzymes were used in the hydrolysis of the natural starch at high concentration (35 % w/v). The time required for liquefaction of starch to 10 dextrose equivalent (DE) and saccharification of liquefied starch to 96 DE increased. Immobilized enzymes showed the potential for use in starch hydrolysis as done in industry.

  11. Effect of omega-3 fatty acids on serum concentrations of adipokines in healthy cats.

    Science.gov (United States)

    Mazaki-Tovi, Michal; Abood, Sarah K; Schenck, Patricia A

    2011-09-01

    To determine associations between serum concentrations of omega-3 polyunsaturated fatty acids and concentrations of adiponectin, leptin, and insulin in healthy cats. 56 healthy adult client-owned cats. Body condition score (BCS) was determined, and blood samples were collected after food was withheld for 12 hours. Serum was harvested for fatty acid analysis and measurement of serum concentrations of adiponectin, leptin, insulin, glucose, triglyceride, and cholesterol. 1 cat was removed because of hyperglycemia. Significant interaction effects between BCS and serum concentrations of eicosapentaenoic acid (EPA) were detected for the analyses of associations between EPA and serum concentrations of adiponectin, insulin, and triglyceride. Cats were categorized into nonobese (BCS, 4 to 6 [n = 34 cats]) and obese (BCS, 7 to 8 [21]) groups; serum concentrations of EPA were directly associated with concentrations of adiponectin and inversely associated with concentrations of insulin and triglyceride in obese cats and were directly associated with concentrations of leptin and inversely associated with concentrations of adiponectin in nonobese cats. Additionally, serum concentrations of docosahexaenoic acid were directly associated with concentrations of adiponectin in obese cats. No significant associations between serum concentrations of docosahexaenoic acid or α-linolenic acid were detected in the analyses for all cats. Female cats had higher serum concentrations of adiponectin and lower concentrations of glucose than did male cats. Increased age was associated with a small increase in serum concentrations of leptin. EPA may ameliorate the decrease in adiponectin and the increase in insulin and triglyceride concentrations in obese cats.

  12. Amino Acid Composition of an Organic Brown Rice Protein Concentrate and Isolate Compared to Soy and Whey Concentrates and Isolates.

    Science.gov (United States)

    Kalman, Douglas S

    2014-06-30

    A protein concentrate (Oryzatein-80™) and a protein isolate (Oryzatein-90™) from organic whole-grain brown rice were analyzed for their amino acid composition. Two samples from different batches of Oryzatein-90™ and one sample of Oryzatein-80™ were provided by Axiom Foods (Los Angeles, CA, USA). Preparation and analysis was carried out by Covance Laboratories (Madison, WI, USA). After hydrolysis in 6-N hydrochloric acid for 24 h at approximately 110 °C and further chemical stabilization, samples were analyzed by HPLC after pre-injection derivitization. Total amino acid content of both the isolate and the concentrate was approximately 78% by weight with 36% essential amino acids and 18% branched-chain amino acids. These results are similar to the profiles of raw and cooked brown rice except in the case of glutamic acid which was 3% lower in the isolate and concentrate. The amino acid content and profile of the Oryzatein-90™ isolate was similar to published values for soy protein isolate but the total, essential, and branched-chain amino acid content of whey protein isolate was 20%, 39% and 33% greater, respectively, than that of Oryzatein-90™. These results provide a valuable addition to the nutrient database of protein isolates and concentrates from cereal grains.

  13. Effects of running the Bostom Marathon on plasma concentrations of large neutral amino acids

    Science.gov (United States)

    Conlay, L. A.; Wurtman, R. J.; Lopez G-Coviella, I.; Blusztajn, J. K.; Vacanti, C. A.; Logue, M.; During, M.; Caballero, B.; Maher, T. J.; Evoniuk, G.

    1989-01-01

    Plasma large neutral amino acid concentrations were measured in thirty-seven subjects before and after completing the Boston Marathon. Concentrations of tyrosine, phenylalanine, and methionine increased, as did their 'plasma ratios' (i.e., the ratio of each amino acid's concentration to the summed plasma concentrations of the other large neutral amino acids which compete with it for brain uptake). No changes were noted in the plasma concentrations of tryptophan, leucine, isoleucine, nor valine; however, the 'plasma ratios' of valine, leucine, and isoleucine all decreased. These changes in plasma amino acid patterns may influence neurotransmitter synthesis.

  14. Cadmium Alters the Concentration of Fatty Acids in THP-1 Macrophages.

    Science.gov (United States)

    Olszowski, Tomasz; Gutowska, Izabela; Baranowska-Bosiacka, Irena; Łukomska, Agnieszka; Drozd, Arleta; Chlubek, Dariusz

    2018-03-01

    Fatty acid composition of human immune cells influences their function. The aim of this study was to evaluate the effects of known toxicant and immunomodulator, cadmium, at low concentrations on levels of selected fatty acids (FAs) in THP-1 macrophages. The differentiation of THP-1 monocytes into macrophages was achieved by administration of phorbol myristate acetate. Macrophages were incubated with various cadmium chloride (CdCl 2 ) solutions for 48 h at final concentrations of 5 nM, 20 nM, 200 nM, and 2 μM CdCl 2 . Fatty acids were extracted from samples according to the Folch method. The fatty acid levels were determined using gas chromatography. The following fatty acids were analyzed: long-chain saturated fatty acids (SFAs) palmitic acid and stearic acid, very long-chain saturated fatty acid (VLSFA) arachidic acid, monounsaturated fatty acids (MUFAs) palmitoleic acid, oleic acid and vaccenic acid, and n-6 polyunsaturated fatty acids (PUFAs) linoleic acid and arachidonic acid. Treatment of macrophages with very low concentrations of cadmium (5-200 nM) resulted in significant reduction in the levels of arachidic, palmitoleic, oleic, vaccenic, and linoleic acids and significant increase in arachidonic acid levels (following exposure to 5 nM Cd), without significant reduction of palmitic and stearic acid levels. Treatment of macrophages with the highest tested cadmium concentration (2 μM) produced significant reduction in the levels of all examined FAs: SFAs, VLSFA, MUFAs, and PUFAs. In conclusion, cadmium at tested concentrations caused significant alterations in THP-1 macrophage fatty acid levels, disrupting their composition, which might dysregulate fatty acid/lipid metabolism thus affecting macrophage behavior and inflammatory state.

  15. Process for recovering a uranium containing concentrate and purified phosphoric acid from a wet process phosphoric acid containing uranium

    International Nuclear Information System (INIS)

    Weterings, C.A.M.; Janssen, J.A.

    1985-01-01

    A process is claimed for recovering from a wet process phosphoric acid which contains uranium, a uranium containing concentrate and a purified phosphoric acid. The wet process phosphoric acid is treated with a precipitant in the presence of a reducing agent and an aliphatic ketone

  16. Process for recovering a uranium containing concentrate and purified phosphoric acid from a wet process phosphoric acid containing uranium

    Energy Technology Data Exchange (ETDEWEB)

    Weterings, C.A.M.; Janssen, J.A.

    1985-04-30

    A process is claimed for recovering from a wet process phosphoric acid which contains uranium, a uranium containing concentrate and a purified phosphoric acid. The wet process phosphoric acid is treated with a precipitant in the presence of a reducing agent and an aliphatic ketone.

  17. Influence of Bleaching on Flavor of 34% Whey Protein Concentrate and Residual Benzoic Acid Concentration in Dried Whey Proteins

    Science.gov (United States)

    Previous studies have shown that bleaching negatively affects the flavor of 70% whey protein concentrate (WPC70), but bleaching effects on lower-protein products have not been established. Benzoyl peroxide (BP), a whey bleaching agent, degrades to benzoic acid (BA) and may elevate BA concentrations...

  18. Influence of bleaching on flavor of 34% whey protein concentrate and residual benzoic acid concentration in dried whey products

    Science.gov (United States)

    Previous studies have shown that bleaching negatively affects the flavor of 70% whey protein concentrate (WPC70), but bleaching effects on lower-protein products have not been established. Benzoyl peroxide (BP), a whey bleaching agent, degrades to benzoic acid (BA) and may elevate BA concentrations...

  19. Genetic polymorphisms and valproic acid plasma concentration in children with epilepsy on valproic acid monotherapy.

    Science.gov (United States)

    Mei, Shenghui; Feng, Weixing; Zhu, Leting; Yu, Yazhen; Yang, Weili; Gao, Baoqin; Wu, Xiaojuan; Zhao, Zhigang; Fang, Fang

    2017-10-01

    The aim of the study is to evaluate the association between genetic polymorphisms and valproic acid (VPA) concentration to dose ratio in children with epilepsy on VPA monotherapy. A total of 137 children, aged 3.5-18 years, (89 males and 48 females) with epilepsy on sustained-release VPA monotherapy were enrolled. Trough plasma concentrations of VPA at steady-state were measured using an AXSYM automatic immunity analyzer. The values were divided by body weight and total daily dose to calculate concentration to dose ratio of VPA (CDRV). Forty-eight single nucleotide polymorphisms involved in the pharmacokinetics of VPA were identified by MassARRAY system. The logarithmic transformed CDRV (lnCDRV) was normally distributed, and PLINK software was used to evaluate the association between genetic polymorphisms and lnCDRV using linear regression adjusted for gender and seizure type. rs28898617 (UGT1A3/4/5/6/7/8/9/10, BETA=0.32, P=0.0089) was significantly associated with higher lnCDRV. No other associations were found. In pediatric patients taking VPA monotherapy, rs28898617 was associated with a higher normalized VPA plasma concentration. Further studies are warranted to confirm the results. Copyright © 2017 British Epilepsy Association. Published by Elsevier Ltd. All rights reserved.

  20. Preconcentration and determination of trace metal ions from aqueous samples by newly developed gallic acid modified Amberlite XAD-16 chelating resin.

    Science.gov (United States)

    Sharma, R K; Pant, Parul

    2009-04-15

    Gallic acid was immobilized on Amberlite XAD-16 by coupling it through -N=N group. The resulting chelating resin Amberlite XAD-16 gallic acid, characterized by thermogravimetric analysis (TGA), infrared (IR) spectra and BET analysis, was used to preconcentrate Cr(III), Mn(II),Fe(III),Co(II), Ni(II) and Cu(II)ions. The resin was employed for the preconcentration of the metal ions present in river water and industrial area aqueous samples. Several parameters like effect of pH, effect of time, effect of sample volume and flow rate of sample were investigated. The sorption capacities for the resin were 216 micromol g(-1), 180 micromol g(-1), 403 micromol g(-1), 281 micromol g(-1), 250 micromol g(-1) and 344 micromol g(-1) for Cr(III), Mn(II), Fe(III), Co(II), Ni(II) and Cu(II) respectively. The preconcentration factors for Cr(III), Mn(II), Fe(III), Ni(II), Co(II) and Cu(II) were found out to be 300, 200, 400, 285.7, 300 and 400 respectively. The effect of various interfering ions was also studied. Results were validated by using standard addition method for river water sample.

  1. Relationship between abscisic acid (ABA) concentration and some ...

    African Journals Online (AJOL)

    saeed

    2011-11-16

    Nov 16, 2011 ... This work investigated the effects of endogenous abscisic acid (ABA) and physiologic parameters related to yield in two ... levels of endogenous ABA contribute to reduced grain growth. Key words: Abscisic acid, ..... Craterostigma plantagineum displays no defined three dimensional structure in its native ...

  2. Resin glycosides from Porana duclouxii.

    Science.gov (United States)

    Ding, Wen-Bing; Zhang, Dai-Gui; Liu, Chun-Jie; Li, Guan-Hua; Li, You-Zhi

    2014-01-01

    A new intact resin glycoside (3) and two glycosidic acids (1 and 2), all having a common trisaccharide moiety and (11S)-hydroxytetradecanoic acid or (3S,11S)-dihydroxytetradecanoic acid as the aglycone, were obtained from the roots of Porana duclouxii. Their structures were elucidated by spectroscopic analyses and chemical correlations. These compounds represent the first examples of resin glycosides from the genus Porana.

  3. Composition of asphaltenes and resins of west Siberian petroleums

    Energy Technology Data Exchange (ETDEWEB)

    Goncharov, I.V.; Babicheva, T.A.; Bodak, A.N.; Nemirovskaya, G.B.; Mashigorov, A.A.

    1985-01-01

    ESR and X-ray diffraction analysis was used to examine asphaltene and resin samples of West Siberia. Experiments were carried out to simulate the effect of catagenesis on resin and asphaltene composition. Processes of thermocatalytic transformations of crude oil in the deposit were found to have no marked effect on asphaltene and resin composition. Transformation of the organic input at sedimentation was assumed to be the main factor determining the qualitative and quantitative composition of crude oil resins and asphaltenes of West Siberia. Petroleums formed from organic matter, accumulating under reducing conditions, contain more asphaltenes and resins, they include much tetravalent vanadium and the asphaltenes have abundant paramagnetic centres. Petroleums formed from oxidized organic matter contain very little asphaltene low concentrations of paramagnetic centers, and little tetravalent vanadium. Resins of these petroleums are rich in oxygen. High levels of asphalt-resin matter in petroleums is related to the presence in the initial organic progenitors of polyunsaturated fatty acids and various nitrogen- and sulfur-containing compounds.

  4. EFFECT OF TEMPERATURE AND CONCENTRATION ON THE VISCOSITY OF AQUEOUS SOLUTIONS OF 3-AMINOPROPANOIC ACID, 4-AMINOBUTANOIC ACID, 5-AMINOPENTANOIC ACID, 6-AMINOHEXANOIC ACID

    Directory of Open Access Journals (Sweden)

    Carmen María Romero

    2011-12-01

    Full Text Available In this work we present the effect of temperatureon the viscosities of aqueous solutionsof 3-aminopropanoic acid, 4-aminobutanoicacid, 5-aminopentanoic acidand 6-aminohexanoic acid as a functionof concentration. The experimental measurementswere done from 293.15 K to308.15 K. At each temperature the experimentaldata were fi tted to the Tsangaris-Martin equation and the B viscosity coefficient was determined. The dependenceof the B coeffi cients on the number ofcarbon atoms of the amino acids is linear,so the contribution of polar and apolargroups was established. The results areinterpreted in terms of amino acid hydration.

  5. Effects of volatile fatty acid concentrations on methane yield and methanogenic bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yuanyuan; Zhang, Yanlin; Wang, Jianbo; Meng, Liang [Engineering Technology Academy, Huazhong Agriculture University, Wuhan 430070 (China)

    2009-05-15

    Volatile fatty acids (VFAs) are important mid-products in the production of methane, and their concentrations affect the efficiency of fermentation. However, their effects on methane yield and methanogenic bacteria growth have been less extensively studied. To address these effects, acetic acid, propionic acid, butyric acid and ethanol were used as substrates and an L{sub 9}(3{sup 4}) orthogonal table was adopted to design anaerobic digestion tests. When the highest concentrations of ethanol, acetic acid and butyric acid were 2400, 2400 and 1800 mg L{sup -1}, respectively, there was no significant inhibition of the activity of methanogenic bacteria. However, when the propionic acid concentration was increased to 900 mg L{sup -1}, significant inhibition appeared, the bacteria concentration decreased from 6 x 10{sup 7} to 0.6-1 x 10{sup 7} ml{sup -1} and their activity would not reconvert. These effects resulted in the accumulation of ethanol and VFAs, and the total methane yield consequently became very low (<321 ml). The original propionic acid concentration had a significant inhibitory effect on methanogenic bacteria growth (P < 0.01). An optimization analysis showed that ethanol, acetic acid, propionic acid and butyric acid at concentrations of 1600, 1600, 300 and 1800 mg L{sup -1}, respectively, led to the maximum accumulative methane yield of 1620 ml and the maximum methanogenic bacteria concentration of 7.3 x 10{sup 8} ml{sup -1}. (author)

  6. Elevational Variation in Soil Amino Acid and Inorganic Nitrogen Concentrations in Taibai Mountain, China.

    Directory of Open Access Journals (Sweden)

    Xiaochuang Cao

    Full Text Available Amino acids are important sources of soil organic nitrogen (N, which is essential for plant nutrition, but detailed information about which amino acids predominant and whether amino acid composition varies with elevation is lacking. In this study, we hypothesized that the concentrations of amino acids in soil would increase and their composition would vary along the elevational gradient of Taibai Mountain, as plant-derived organic matter accumulated and N mineralization and microbial immobilization of amino acids slowed with reduced soil temperature. Results showed that the concentrations of soil extractable total N, extractable organic N and amino acids significantly increased with elevation due to the accumulation of soil organic matter and the greater N content. Soil extractable organic N concentration was significantly greater than that of the extractable inorganic N (NO3--N + NH4+-N. On average, soil adsorbed amino acid concentration was approximately 5-fold greater than that of the free amino acids, which indicates that adsorbed amino acids extracted with the strong salt solution likely represent a potential source for the replenishment of free amino acids. We found no appreciable evidence to suggest that amino acids with simple molecular structure were dominant at low elevations, whereas amino acids with high molecular weight and complex aromatic structure dominated the high elevations. Across the elevational gradient, the amino acid pool was dominated by alanine, aspartic acid, glycine, glutamic acid, histidine, serine and threonine. These seven amino acids accounted for approximately 68.9% of the total hydrolyzable amino acid pool. The proportions of isoleucine, tyrosine and methionine varied with elevation, while soil major amino acid composition (including alanine, arginine, aspartic acid, glycine, histidine, leucine, phenylalanine, serine, threonine and valine did not vary appreciably with elevation (p>0.10. The compositional

  7. Use of a phenolic-carboxylic acid cation resin in the treatment of low-level liquid waste at Oak Ridge National Laboratory

    International Nuclear Information System (INIS)

    Chilton, J.M.

    1981-09-01

    The loading capacity of CS-100 resin, using plant waste as feed, was found to be significantly reduced after 20 loading-elution cycles; one-fourth or less of the original capacity was retained after 30 cycles. No important differences were noted between an untreated column and a column that had been reconverted to the sodium form in the regeneration step. Omission of the sodium regeneration could not be adopted as a routine procedure because it produced a packing effect in the plant beds; however, reconversion to the sodium form is now achieved by using a stoichiometric amount of caustic rather than a 100% excess, as was previous practice. Since the distribution coefficients for calcium and strontium are about six times greater than that for cesium, no loss of 90 Sr would be expected while 137 Cs is loading. Laboratory results obtained by using plant conditions and feed indicate that a typical bed would remove 96% of 90 Sr in the feed. Cobalt-60 is generally the greatest contributor to the radioactivity of the plant effluent. Laboratory tests indicate that this 60 Co is present as a mixture of a soluble anionic complex and insoluble colloids. The anionic complex could be removed by placing an anion exchange column in the effluent from the CS-100 resin bed. In studies of the dynamics of loading on CS-100 resin, the contact time in plant operation (3 to 4 min per column volume) was found to be more than adequate to obtain the desired results. Effects of flow velocity were not investigated. Data from a series of laboratory experiments show that CS-100 resin can be eluted satisfactorily with 0.5 to 1.0 M formic or acetic acid, although a larger volume is required than for elution with 0.5 M nitric acid

  8. Use of water as displacing agent in ion exchange chromatographic separation of isotope of boron using weak base ion exchange resin

    International Nuclear Information System (INIS)

    Sharma, B.K.; Mohanakrishnan, G.; Anand Babu, C.; Krishna Prabhu, R.

    2008-01-01

    Experiments were undertaken to study the feasibility of using weakly basic anion exchange resin for enrichment of isotopes of boron by ion exchange chromatography and water as eluent. The results of experiments carried out to determine total chloride capacity (TCC), strong base capacity (SBC) of the resin at different concentrations of boric acid and enrichment profiles are reported in this paper. (author)

  9. Determination of concentration and molar absorptivity of hypochlorous acid and hypobromous acid species by hydrogen peroxide titration

    Science.gov (United States)

    Uehara, H.; Arakaki, T.

    2017-12-01

    Hypochlorous acid and hypobromous acid (abbreviated as "HypoX acids") are the main ingredients of bleaching and bactericides. The HypoX acids change their chemical forms depending on environmental factors such as pH and various chemical reactions. For example, it has been reported that hypobromite ion in water changes to carcinogenic bromate by photochemical reaction with ultraviolet light. In this study, concentrations of HypoX acids were determined by UV-VIS absorbance measurement utilizing the fact that HypoX acids react with hydrogen peroxide and do not co-exist in the solution. The method for determining the concentration by titration with hydrogen peroxide can be carried out simpler and more efficiently than the DPD method or the current titration method generally used for chlorine concentration measurement. Molar absorptivity between 250 - 500 nm of HypoX acids, including their conjugate base species, was determined by solving theoretical acid-base formula including molar fraction of each chemical species at various pHs. Molar absorptivity of OCl- and OBr- between 250 - 500 nm was determined based on the concentrations obtained from titration with hydrogen peroxide and absorbance at pH > 10, where OCl- and OBr- dominate. Furthermore, the HypoX acids solutions were irradiated with a solar simulator, and the photolysis rate constants were obtained. Based on those values, the half-lives were calculated and the behavior of HypoX acids in the environment was elucidated.

  10. Effect of acid etching duration on tensile bond strength of composite resin bonded to erbium:yttrium-aluminium-garnet laser-prepared dentine. Preliminary study.

    Science.gov (United States)

    Chousterman, M; Heysselaer, D; Dridi, S M; Bayet, F; Misset, B; Lamard, L; Peremans, A; Nyssen-Behets, C; Nammour, S

    2010-11-01

    The purpose of this study was to compare the tensile bond strength of composite resin bonded to erbium:yttrium-aluminium-garnet (Er:YAG) laser-prepared dentine after different durations of acid etching. The occlusal third of 68 human third molars was removed in order to expose the dentine surface. The teeth were randomly divided into five groups: group B (control group), prepared with bur and total etch system with 15 s acid etching [37% orthophosphoric acid (H(3)PO(4))]; group L15, laser photo-ablated dentine (200 mJ) (laser irradiation conditions: pulse duration 100 micros, air-water spray, fluence 31.45 J/ cm(2), 10 Hz, non-contact hand pieces, beam spot size 0.9 mm, irradiation speed 3 mm/s, and total irradiation time 2 x 40 s); group L30, laser prepared, laser conditioned and 30 s acid etching; group L60, laser prepared, laser conditioned and 60 s acid etching; group L90, laser prepared, laser conditioned and 90 s acid etching. A plot of composite resin was bonded onto each exposed dentine and then tested for tensile bond strength. The values obtained were statistically analysed by analysis of variance (ANOVA) coupled with the Tukey-Kramer test at the 95% level. A 90 s acid etching before bonding showed the best bonding value (P < 0.05) when compared with all the other groups including the control group. There is no significance difference between other groups, nor within each group and the control group. There was a significant increase in tensile bond strength of the samples acid etched for 90 s.

  11. Serum uric acid concentration in patients with type-2 diabetes mellitus during diet or glibenclamide therapy

    International Nuclear Information System (INIS)

    Mahmood, I.H.

    2007-01-01

    To investigate serum uric acid concentration in patients with type 2 diabetes mellitus. This is a case control study conducted in Al-Wafa Diabetic Center in Mosul over a period of one year starting from January 1, 2005 to January 1, 2006. Serum glucose concentration and uric acid concentration were measured in both control and patient's groups (group 1 patients on diet therapy, group 2 patients on glibenclamide therapy and group 3 involve naturopathic patients). Serum glucose concentration was high in the diabetic groups as compared with the control group (P 0.2) except in group-3 (P<0.05). A negative correlation was reported between hyperglycemia and uric acid concentration of the different groups. Serum uric acid concentration is slightly reduced in type 2 diabetic patients particularly in the complicated patients with peripheral neuropathy and this may be due to the oxidative stress that decreases the antioxidant capacity of the body involving uric acid. (author)

  12. High serum uric acid concentration predicts poor survival in patients with breast cancer.

    Science.gov (United States)

    Yue, Cai-Feng; Feng, Pin-Ning; Yao, Zhen-Rong; Yu, Xue-Gao; Lin, Wen-Bin; Qian, Yuan-Min; Guo, Yun-Miao; Li, Lai-Sheng; Liu, Min

    2017-10-01

    Uric acid is a product of purine metabolism. Recently, uric acid has gained much attraction in cancer. In this study, we aim to investigate the clinicopathological and prognostic significance of serum uric acid concentration in breast cancer patients. A total of 443 female patients with histopathologically diagnosed breast cancer were included. After a mean follow-up time of 56months, survival was analysed using the Kaplan-Meier method. To further evaluate the prognostic significance of uric acid concentrations, univariate and multivariate Cox regression analyses were applied. Of the clinicopathological parameters, uric acid concentration was associated with age, body mass index, ER status and PR status. Univariate analysis identified that patients with increased uric acid concentration had a significantly inferior overall survival (HR 2.13, 95% CI 1.15-3.94, p=0.016). In multivariate analysis, we found that high uric acid concentration is an independent prognostic factor predicting death, but insufficient to predict local relapse or distant metastasis. Kaplan-Meier analysis indicated that high uric acid concentration is related to the poor overall survival (p=0.013). High uric acid concentration predicts poor survival in patients with breast cancer, and might serve as a potential marker for appropriate management of breast cancer patients. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Adsorption kinetics, isotherm, and thermodynamics studies of acetyl-11-keto-β-boswellic acids (AKBA) from Boswellia serrata extract using macroporous resin.

    Science.gov (United States)

    Niphadkar, Sonali S; Rathod, Virendra K

    2017-09-14

    An acetyl-11-keto-β-boswellic acid (AKBA) is potent anti-inflammatory agent found in Boswellia serrata oleogum resin. Adsorption characteristics of AKBA from B. serrata were studied using macroporous adsorbent resin to understand separation and adsorption mechanism of targeted molecules. Different macroporous resins were screened for adsorption and desorption of AKBA and Indion 830 was screened as it showed higher adsorption capacity. The kinetic equations were studied and results showed that the adsorption of AKBA on Indion 830 was well fitted to the pseudo first-order kinetic model. The influence of two parameters such as temperature (298, 303, and 308 K) and pH (5-8) on the adsorption process was also studied. The experimental data was further investigated using Langmuir, Freundlich, and Temkin isotherm models. It was observed that Langmuir isotherm model was found to be the best fit for AKBA adsorption by Indion 830 and highest adsorption capacity (50.34 mg/g) was obtained at temperature of 303 K. The values of thermodynamic parameters such as the change of Gibbs free energy (ΔG*), entropy (ΔS*), and enthalpy (ΔH*), indicated that the process of adsorption was spontaneous, favourable, and exothermic.

  14. Ion exchange removal of chromium (iii) from tannery wastes by using a strong acid cation exchange resin amberlite ir-120 h+ and its hybrids

    International Nuclear Information System (INIS)

    Ahmad, T.

    2014-01-01

    A strong acid cation exchange resin Amberlite IR-120 H+ and its hybrids with Mn(OH)/sub 2/, Cu(OH)/sub 2/ and Fe(OH)/sub 3/ are used for the removal of chromium (III) from spent tannery bath. The experimental data give good fits with the Langmuir sorption model. The thermodynamic parameters entropy (delta S), enthalpy (delta H) and free energy (delta G) changes are computed, which reveal that the chromium removal from tannery wastes by ion exchangers is an endothermic, physical sorption and entropically driven process. The rate of sorption is found to increase with the increase of resin dosage, stirring speed and temperature. Different kinetic models such as film diffusion, particle diffusion and Lagergren pseudo first order are used to evaluate the mechanism of the process. It is found that the hybrid ion exchange resins have better removal capacity as compared to the parent ion exchanger. The increase in the removal capacity is found to be in the order of the corresponding PZC values of the hybrid ion exchangers. Further, it is suggested that the higher exchange capacity is the result of Donnan effect and specific adsorption of chromium by the oxides / hydroxides present inside the matrix of the organic cation exchanger. (author)

  15. Plasma Concentration of Ascorbic Acid and Some Hematological ...

    African Journals Online (AJOL)

    Background: Tobacco snuffing, like cigarette smoking, is known to be a common habit among the adults of Igbo communities in Nigeria. In view of the various pharmacological actions of nicotine and other additive constituents of tobacco snuff, there is growing concern that ascorbic acid, which is a vital antioxidant, and blood ...

  16. Urinary ascorbic acid and serum concentrations of circulating ...

    African Journals Online (AJOL)

    The aim of the present study was to determine the presence or absence of ascorbic acid in urine and serum levels of circulating immune complexes (CIC) and albumin in HIV infected subjects. A total of 90 participants (30 Symptomatic HIV infected subjects on antiretroviral therapy (ART), 30 Symptomatic HIV infected ...

  17. Relationship between abscisic acid (ABA) concentration and some ...

    African Journals Online (AJOL)

    This work investigated the effects of endogenous abscisic acid (ABA) and physiologic parameters related to yield in two wheat cultivars (Triticum aestivum L.), Marvdasht and Zagros (sensitive and tolerant to terminal season drought, respectively) grown in pots under well watered and water-stressed starting from anthesis ...

  18. Using Conductivity Measurements to Determine the Identities and Concentrations of Unknown Acids: An Inquiry Laboratory Experiment

    Science.gov (United States)

    Smith, K. Christopher; Garza, Ariana

    2015-01-01

    This paper describes a student designed experiment using titrations involving conductivity measurements to identify unknown acids as being either HCl or H[subscript 2]SO[subscript 4], and to determine the concentrations of the acids, thereby improving the utility of standard acid-base titrations. Using an inquiry context, students gain experience…

  19. Kinetics of soybean oil epoxidation with peracetic acid formed in situ in the presence of an ion exchange resin: Pseudo-homogeneous model

    Directory of Open Access Journals (Sweden)

    Janković Milovan

    2017-01-01

    Full Text Available A kinetic model was proposed for the epoxidation of vegetable oils with peracetic acid formed in situ from acetic acid and hydrogen peroxide in the presence of an acidic ion exchange resin as a catalyst. The model is pseudo-homogeneous with respect to the catalyst. Besides the main reactions of peracetic acid and epoxy ring formation, the model takes into account the side reaction of epoxy ring opening with acetic acid. The partitioning of acetic acid and peracetic acid between the aqueous and organic phases and the change in the phases’ volumes during the process were considered. The temperature dependency of the apparent reaction rate coefficients is described by a reparameterized Arrhenius equation. The constants in the proposed model were estimated by fitting the experimental data obtained for the epoxidations of soybean oil conducted under defined reaction conditions. The highest epoxy yield of 87.73% was obtained at 338 K when the mole ratio of oil unsaturation:acetic acid:hydrogen peroxide was 1:0.5:1.35 and when the amount of the catalyst Amberlite IR-120H was 4.04 wt.% of oil. Compared to the other reported pseudo-homogeneous models, the model proposed in this study better correlates the change of double bond and epoxy group contents during the epoxidation process. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III45022

  20. Cheese intake lowers plasma cholesterol concentrations without increasing bile acid excretion

    OpenAIRE

    Hjerpsted, Julie Bousgaard; Dragsted, Lars Ove; Tholstrup, Tine

    2016-01-01

    Purpose Cheese is a dairy product with high calcium content. It has been suggested that calcium intake may increase fecal excretion of bile acids that would cause a regeneration of bile acids from hepatic cholesterol and thereby result in a lowering of plasma cholesterol concentrations. We aimed to test this hypothesis by assessing bile acid and calcium concentrations in fecal samples from humans after intake of cheese and butter. Methods The study was a randomized, 2 × 6 weeks crossover, die...

  1. Ion exchange and protonation equilibria of an amphoteric ion-exchange resin in the presence of simple salt.

    Science.gov (United States)

    Miyazaki, Yoshinobu; Qu, Hui; Konaka, Junko

    2008-09-01

    The influence of simple salts on the ion exchange and protonation equilibria of an amphoteric ion-exchange resin, which has strong base and weak acid moieties in a single functional group fixed onto the styrene-DVB matrix, has been investigated. Concentrations of ionic species in the amphoteric ion-exchange resin in equilibrium with various sodium salt solutions were estimated by (23)Na NMR spectroscopy. For the NaClO(4) system, the ratio of sodium ion concentration in the resin phase to that in the equilibrium solution was greater than 1 and increased with a decrease in the salt concentration. In contrast to an ordinary cation-exchange resin, the ion exchange behavior of Mg(2+) and Ca(2+) on the amphoteric ion-exchange resin showed a marked dependence on the kinds of salts: the distribution coefficients for the NaCl system were independent of the salt concentration, while the log D vs. log[Na(+)] plots for the NaClO(4) system showed linear relationships with slopes being neither -2 nor 0. Apparent protonation constants of the carboxylate in the functional group of the resin in equilibrium with NaClO(4) solutions were greater than those with NaCl solutions. The ion exchange and protonation properties of the amphoteric ion-exchange resin were elucidated on the basis of the information about the salt concentrations in the resin phase estimated by the NMR method.

  2. Metabolic syndrome, alcohol consumption and genetic factors are associated with serum uric acid concentration.

    Science.gov (United States)

    Stibůrková, Blanka; Pavlíková, Markéta; Sokolová, Jitka; Kožich, Viktor

    2014-01-01

    Uric acid is the end product of purine metabolism in humans, and increased serum uric acid concentrations lead to gout. The objective of the current study was to identify factors that are independently associated with serum uric acid concentrations in a cohort of Czech control individuals. The cohort consisted of 589 healthy subjects aged 18-65 years. We studied the associations between the serum uric acid concentration and the following: (i) demographic, anthropometric and other variables previously reported to be associated with serum uric acid concentrations; (ii) the presence of metabolic syndrome and the levels of metabolic syndrome components; and (iii) selected genetic variants of the MTHFR (c.665C>T, c.1286A>C), SLC2A9 (c.844G>A, c.881G>A) and ABCG2 genes (c.421C>A). A backward model selection procedure was used to build two multiple linear regression models; in the second model, the number of metabolic syndrome criteria that were met replaced the metabolic syndrome-related variables. The models had coefficients of determination of 0.59 and 0.53. The serum uric acid concentration strongly correlated with conventional determinants including male sex, and with metabolic syndrome-related variables. In the simplified second model, the serum uric acid concentration positively correlated with the number of metabolic syndrome criteria that were met, and this model retained the explanatory power of the first model. Moderate wine drinking did not increase serum uric acid concentrations, and the urate transporter ABCG2, unlike MTHFR, was a genetic determinant of serum uric acid concentrations. Metabolic syndrome, moderate wine drinking and the c.421C>A variant in the ABCG gene are independently associated with the serum uric acid concentration. Our model indicates that uric acid should be clinically monitored in persons with metabolic syndrome.

  3. Metabolic syndrome, alcohol consumption and genetic factors are associated with serum uric acid concentration.

    Directory of Open Access Journals (Sweden)

    Blanka Stibůrková

    Full Text Available Uric acid is the end product of purine metabolism in humans, and increased serum uric acid concentrations lead to gout. The objective of the current study was to identify factors that are independently associated with serum uric acid concentrations in a cohort of Czech control individuals.The cohort consisted of 589 healthy subjects aged 18-65 years. We studied the associations between the serum uric acid concentration and the following: (i demographic, anthropometric and other variables previously reported to be associated with serum uric acid concentrations; (ii the presence of metabolic syndrome and the levels of metabolic syndrome components; and (iii selected genetic variants of the MTHFR (c.665C>T, c.1286A>C, SLC2A9 (c.844G>A, c.881G>A and ABCG2 genes (c.421C>A. A backward model selection procedure was used to build two multiple linear regression models; in the second model, the number of metabolic syndrome criteria that were met replaced the metabolic syndrome-related variables.The models had coefficients of determination of 0.59 and 0.53. The serum uric acid concentration strongly correlated with conventional determinants including male sex, and with metabolic syndrome-related variables. In the simplified second model, the serum uric acid concentration positively correlated with the number of metabolic syndrome criteria that were met, and this model retained the explanatory power of the first model. Moderate wine drinking did not increase serum uric acid concentrations, and the urate transporter ABCG2, unlike MTHFR, was a genetic determinant of serum uric acid concentrations.Metabolic syndrome, moderate wine drinking and the c.421C>A variant in the ABCG gene are independently associated with the serum uric acid concentration. Our model indicates that uric acid should be clinically monitored in persons with metabolic syndrome.

  4. Evaluation of ultrasonic technique to characterize the concentration of boric acid in liquid medium

    International Nuclear Information System (INIS)

    Kohara, Richard Yuzo Ramida

    2015-01-01

    This dissertation is to analyze the viability of using ultrasonic technique to characterize the concentration of boric acid in liquid medium non-invasively, therefore, ultrasonic tests were performed relating different boric acid concentrations with the travel time of the ultrasonic wave, also were evaluated factors able to mask the characterization of these concentrations by ultrasonic technique. The results showed that the ultrasonic technique allows the characterization of boric acid concentrations in liquid medium in very simple terms by the ultrasonic wave travel time, requiring further studies in complex conditions. (author)

  5. Preparative concentration of nucleic acids fragments by capillary isotachophoretic analyzer

    Czech Academy of Sciences Publication Activity Database

    Datinská, Vladimíra; Voráčová, Ivona; Berka, J.; Foret, František

    2018-01-01

    Roč. 1548 (2018), s. 100-103 ISSN 0021-9673 R&D Projects: GA MŠk(CZ) LQ1601; GA ČR(CZ) GBP206/12/G014; GA MŠk(CZ) 8F17003 Institutional support: RVO:68081715 Keywords : DNA * isotachophoresis * nucleic acids * sample preparation Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 3.981, year: 2016

  6. High plasma uric acid concentration: causes and consequences

    Directory of Open Access Journals (Sweden)

    de Oliveira Erick

    2012-04-01

    Full Text Available Abstract High plasma uric acid (UA is a precipitating factor for gout and renal calculi as well as a strong risk factor for Metabolic Syndrome and cardiovascular disease. The main causes for higher plasma UA are either lower excretion, higher synthesis or both. Higher waist circumference and the BMI are associated with higher insulin resistance and leptin production, and both reduce uric acid excretion. The synthesis of fatty acids (tryglicerides in the liver is associated with the de novo synthesis of purine, accelerating UA production. The role played by diet on hyperuricemia has not yet been fully clarified, but high intake of fructose-rich industrialized food and high alcohol intake (particularly beer seem to influence uricemia. It is not known whether UA would be a causal factor or an antioxidant protective response. Most authors do not consider the UA as a risk factor, but presenting antioxidant function. UA contributes to > 50% of the antioxidant capacity of the blood. There is still no consensus if UA is a protective or a risk factor, however, it seems that acute elevation is a protective factor, whereas chronic elevation a risk for disease.

  7. Spectra and concentration profiles throughout the reaction of curing epoxy resins from near-infrared spectroscopy and multivariate curve resolution methods.

    Science.gov (United States)

    Larrechi, M S; Rius, F X

    2004-01-01

    When applied to near-infrared (NIR) data, multivariate curve resolution methods, in particular alternating least squares (ALS), make it possible to calculate the concentration profiles and the spectra of all species involved in the reaction of curing epoxy resins. In this paper, the model reaction between phenyl glicidyl ether and aniline (2:1) was studied at 95 degrees C. A NIR spectrum was recorded every five minutes throughout the eight-hour reaction process. The data display rank deficiency. This problem was overcome by supplying additional information to the system in the form of known spectra of some reactants. The recovered spectra and concentration profiles satisfactorily reproduced the experimental data. In this way, 99.99% of the variance associated with the experimental matrix was reproduced. A value of 0.87% was obtained for lack of fit while the similarity coefficient r between the spectra recovered and the spectra corresponding to the three pure species involved in the reaction were PGE (r = 0.994), aniline (r = 0.994), and tertiary amine (r = 0.999). The maximum and minimum limits associated with the ALS solutions were calculated, which made it possible to limit to a considerable extent the ambiguity that is characteristic of these curve resolution methods.

  8. Process for the winning of a concentrate containing uranium and purified phosphoric acid, as well as the concentrate containing uranium and purified phosphoric acid obtained by this process

    International Nuclear Information System (INIS)

    1980-01-01

    The uranium containing concentrate and purified phosphoric acid are obtained by treating wet phosphoric acid with an inorganic fluorine compound (ammonium fluoride) and an aliphatic ketone (acetone) in the presence of a reducing agent (finely divided iron). The ketone is added first and the formed uranium precipitate is separated from the solution. If the fluorine compound is added first, the yield is lowered by a factor of 2. (Th.P.)

  9. Organosulfates and organic acids in Arctic aerosols: speciation, annual variation and concentration levels

    Science.gov (United States)

    Hansen, A. M. K.; Kristensen, K.; Nguyen, Q. T.; Zare, A.; Cozzi, F.; Nøjgaard, J. K.; Skov, H.; Brandt, J.; Christensen, J. H.; Ström, J.; Tunved, P.; Krejci, R.; Glasius, M.

    2014-08-01

    Sources, composition and occurrence of secondary organic aerosols in the Arctic were investigated at Zeppelin Mountain, Svalbard, and Station Nord, northeastern Greenland, during the full annual cycle of 2008 and 2010, respectively. Speciation of organic acids, organosulfates and nitrooxy organosulfates - from both anthropogenic and biogenic precursors were in focus. A total of 11 organic acids (terpenylic acid, benzoic acid, phthalic acid, pinic acid, suberic acid, azelaic acid, adipic acid, pimelic acid, pinonic acid, diaterpenylic acid acetate and 3-methyl-1,2,3-butanetricarboxylic acid), 12 organosulfates and 1 nitrooxy organosulfate were identified in aerosol samples from the two sites using a high-performance liquid chromatograph (HPLC) coupled to a quadrupole Time-of-Flight mass spectrometer. At Station Nord, compound concentrations followed a distinct annual pattern, where high mean concentrations of organosulfates (47 ± 14 ng m-3) and organic acids (11.5 ± 4 ng m-3) were observed in January, February and March, contrary to considerably lower mean concentrations of organosulfates (2 ± 3 ng m-3) and organic acids (2.2 ± 1 ng m-3) observed during the rest of the year. At Zeppelin Mountain, organosulfate and organic acid concentrations remained relatively constant during most of the year at a mean concentration of 15 ± 4 ng m-3 and 3.9 ± 1 ng m-3, respectively. However during four weeks of spring, remarkably higher concentrations of total organosulfates (23-36 ng m-3) and total organic acids (7-10 ng m-3) were observed. Elevated organosulfate and organic acid concentrations coincided with the Arctic haze period at both stations, where northern Eurasia was identified as the main source region. Air mass transport from northern Eurasia to Zeppelin Mountain was associated with a 100% increase in the number of detected organosulfate species compared with periods of air mass transport from the Arctic Ocean, Scandinavia and Greenland. The results from this

  10. Reaction catalysts of urea-formaldehyde resin, as related to strength properties of southern pine particleboard

    Science.gov (United States)

    C. -Y. Hse

    1974-01-01

    Twelve resins were formulated with factorial combinations of three alkaline catalysts (i.e., somdium hydroxide, hexamethylenetetramine, and triethanolamine) and four acidic catalysts (i.e., acetic acid, hydrochloric acid, ammonium chloride, and phosphoric acid). The resins were replicated.

  11. Rheology of dilute acid hydrolyzed corn stover at high solids concentration.

    Science.gov (United States)

    Ehrhardt, M R; Monz, T O; Root, T W; Connelly, R K; Scott, C T; Klingenberg, D J

    2010-02-01

    The rheological properties of acid hydrolyzed corn stover at high solids concentration (20-35 wt.%) were investigated using torque rheometry. These materials are yield stress fluids whose rheological properties can be well represented by the Bingham model. Yield stresses increase with increasing solids concentration and decrease with increasing hydrolysis reaction temperature, acid concentration, and rheometer temperature. Plastic viscosities increase with increasing solids concentration and tend to decrease with increasing reaction temperature and acid concentration. The solids concentration dependence of the yield stress is consistent with that reported for other fibrous systems. The changes in yield stress with reaction conditions are consistent with observed changes in particle size. This study illustrates that torque rheometry can be used effectively to measure rheological properties of concentrated biomass.

  12. Study of the interaction metallic cation - ligand in concentrated phosphorus acid media; Etude de l'interaction cation metallique - ligand en milieu acide phosphorique concentre

    Energy Technology Data Exchange (ETDEWEB)

    Sefiani, N.; Azzi, M.; Hlaibi, M. [Faculte des Sciences Ain Chock, Laboratoire d' Electrochimie et Chimie de l' Environnement (LECE), Casablanca (Morocco); Kossair, A. [Centre de Recherche des Phosphates Mineraux (CERPHOS), Casablanca (Morocco)

    2005-07-01

    The phosphoric acid is more and more used with a high purity. The recovery of recycling element (uranium, vanadium, rare earth...) and the elimination of toxic element (cadmium, molybdenum, lead...) contained in the phosphoric acid are generally realized by extraction or precipitation. It is then very important to understand these impurities behavior in the phosphoric media in order to control their elimination. In this work, the authors considered the presence of some metallic cations (V, Al, fe, U) and fluorides ions as impurity in concentrated phosphoric acid media. (A.L.B.)

  13. Microbial treatment of ion exchange resins

    International Nuclear Information System (INIS)

    Kouznetsov, A.; Kniazev, O.

    2001-01-01

    A bioavailability of ion exchange resins to a microbial destruction as one of the alternative methods of compacting used ionites from the nuclear fuel manufacturing cycle enterprises has been investigated. The bio-destruction was studied after a preliminary chemical treatment or without it. A sensitivity of the ion exchange resins (including highly acidic cationite KU-2-8) to the microbial destruction by heterotrophic and chemo-litho-trophic microorganisms under aerobic conditions was shown in principle. The biodegradation of the original polymer is possible in the presence of the water soluble fraction of the resin obtained after its treatment by Fenton reagent and accelerated in the presence of Mn-ions in optimal concentration 1-2 g of Mn per liter of medium. Thus, the process of bio-destruction of ionite polymer by heterotrophic microorganisms can be compared with the bio-destruction of lignin or humic substances. The optimum parameters of bio-destruction and microorganisms used must be different for resins with different functional groups. (authors)

  14. Microbial treatment of ion exchange resins

    Energy Technology Data Exchange (ETDEWEB)

    Kouznetsov, A.; Kniazev, O. [D. Mendeleyev University of Chemical Technology of Russia, Dept. Biotechnology, Mocow (Russian Federation)

    2001-07-01

    A bioavailability of ion exchange resins to a microbial destruction as one of the alternative methods of compacting used ionites from the nuclear fuel manufacturing cycle enterprises has been investigated. The bio-destruction was studied after a preliminary chemical treatment or without it. A sensitivity of the ion exchange resins (including highly acidic cationite KU-2-8) to the microbial destruction by heterotrophic and chemo-litho-trophic microorganisms under aerobic conditions was shown in principle. The biodegradation of the original polymer is possible in the presence of the water soluble fraction of the resin obtained after its treatment by Fenton reagent and accelerated in the presence of Mn-ions in optimal concentration 1-2 g of Mn per liter of medium. Thus, the process of bio-destruction of ionite polymer by heterotrophic microorganisms can be compared with the bio-destruction of lignin or humic substances. The optimum parameters of bio-destruction and microorganisms used must be different for resins with different functional groups. (authors)

  15. Effect of strenuous exercise on urine concentrations of homovanillic acid, cortisol, and vanillylmandelic acid in sled dogs.

    Science.gov (United States)

    Durocher, Lawren L; Hinchcliff, Kenneth W; Williamson, Kathy K; McKenzie, Erica C; Holbrook, Todd C; Willard, Michael; Royer, Chris M; Davis, Michael S

    2007-01-01

    To determine whether prolonged exercise by conditioned sled dogs affects urine concentrations of homovanillic acid (a metabolite of dopamine), vanillylmandelic acid (a metabolite of norepinephrine and epinephrine), and cortisol. 24 conditioned Alaskan sled dogs (2 to 8.5 years old) that were in training for a multiday endurance race. Voided urine samples were collected from 4 groups of dogs (randomly selected from 54 dogs) after no exercise (control group; n = 6 dogs), completion of a 160km run (group A; 3), completion of a 420-km run (group B; 7), and completion of a 560-km run (group C; 6). Urine cortisol concentrations were determined by use of an immunoassay technique; urine vanillylmandelic acid and homovanillic acid concentrations were measured via high-performance liquid chromatography. Compared with the control group, urine cortisol concentration in groups A, B, and C was significantly different (5.33 x 10(4) +/- 2.62 x 10(4) microg/dL vs 1.04 x 10(4) +/- 2.31 x 10(5) microg/dL, 8.88 x 10(4) +/- 5.49 x 10(4) microg/dL, and 6.31 x 10(4) +/- 5.09 x 10(4) microg/dL, respectively). Urine homovanillic acid concentration did not differ among the 4 groups. Vanillylmandelic acid was not detected in any urine samples. Results indicated that prolonged exercise by sled dogs did not affect urine homovanillic acid concentration but did increase urinary cortisol secretion, which is indicative of adrenocortical stimulation. The apparent lack of vanillylmandelic acid in voided urine samples requires further investigation.

  16. Recovery of uranium in the production of concentrated phosphoric acid by a hemihydrate process

    International Nuclear Information System (INIS)

    Nakajima, S.; Miyamoto, M.

    1983-01-01

    Nissan Chemical Industries as manufacturers of phosphoric acid have studied the recovery of uranium, based on a concentrated phosphoric acid production process. The process consists of two stages, a hemihydrate stage with a formation of hemihydrate and a filtration section, followed by a dihydrate stage with hydration and a filtration section. In the hemihydrate stage, phosphate is treated with a mixture of phosphoric acid and sulphuric acid to produce phosphoric acid and hydrous calcium sulphate; the product is recovered in the filtration section and its concentration is 40-50% P 2 O 3 . In the dihydrate stage, the hemihydrate is transformed by re-dissolution and hydration, producing hydrous calcium sulphate, i.e. gypsum. This process therefore comprises two parts, each with different acid concentrations. As the extraction of uranium is easier in the case of a low concentration of phosphoric acid, the process consists of the recovery of uranium starting from the filtrate of the hydration section. The tests have shown that the yield of recovery of uranium was of the order of 80% disregarding the handling losses and no disadvantageous effect has been found in the combination of the process of uranium extraction with the process of concentrated phosphoric acid production. Compared with the classical process where uranium is recovered from acid with 30% P 2 O 5 , the process of producing high-concentration phosphoric acid such as the Nissan process, in which the uranium recovery is effected from acid with 15% P 2 O 5 from the hydration section, presents many advantages [fr

  17. Effect of pH and complementary ion concentration on nitrate removal using puroliteA400 Resin impregnated Cu in batch system

    Science.gov (United States)

    Turmuzi, M.; Tarigan, Z. N.; Nadapdap, L.; Batubara, F.

    2018-02-01

    The total nitrogen content in water bodies should be below 50 mg NO3 -/L (11.3 mgN/l) World Health Organization (WHO) 2006. The content of nitrogen exceeding the quality standard threshold will cause damage to the aquatic ecosystem and be carcinogenic to humans. The Purolite A-400 resin will be modified with Cu metal by batch method to see the adsorption allowance of nitrate in synthetic liquid waste with nitrate concentration of 50 mg/l. This study will evaluate the effect of pH and complementary ions on the adsorption process. From the result of the research, the second order pseudo model is the most suitable adsorption kinetics model. For the adsorption isotherms the most suitable model is the Freundlich adsorption isotherm model. The optimum pH conditions were at the range of 8.5. The addition of complementary ions sulfate and phosphate did not show any significant change, but sulfate is the most effective complementary ion with a content of 20 mg/l.

  18. Relationship between adipic acid concentration and the core symptoms of autism spectrum disorders.

    Science.gov (United States)

    Puig-Alcaraz, Carmen; Fuentes-Albero, Milagros; Cauli, Omar

    2016-08-30

    Dicarboxylic acids are an important source of information about metabolism and potential physiopathological alterations in children with autism spectrum disorders (ASDs). We measured the concentration between dicarboxylic adipic and suberic acids in children with an ASD and typically-developing (TD) children and analyzed any relationships between the severity of the core symptoms of ASDs and other clinical features (drugs, supplements, drugs, or diet). The core symptoms of autism were evaluated using the DSM-IV criteria, and adipic acid and suberic acid were measured in urine samples. Overall, no increase in the concentration of adipic acid in children with ASDs compared to TD children, however when considering vitamin B supplementation in ASD there were significantly increased level of urinary adipic acid in children with an ASD not taking vitamin B supplementation compared to supplemented children or to TD children. No significant difference were observed in suberic acid. Interestingly, the increase in adipic acid concentration was significantly and indirectly correlated with the severity of the deficit in socialization and communication skills in children with an ASD. Therefore, therapeutic treatments aimed at decreasing adipic acid concentration might not be beneficial for treating the core symptoms of ASDs. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  19. Evolution of Diterpene Metabolism: Sitka Spruce CYP720B4 Catalyzes Multiple Oxidations in Resin Acid Biosynthesis of Conifer Defense against Insects1[C][W][OA

    Science.gov (United States)

    Hamberger, Björn; Ohnishi, Toshiyuki; Hamberger, Britta; Séguin, Armand; Bohlmann, Jörg

    2011-01-01

    Diterpene resin acids (DRAs) are specialized (secondary) metabolites of the oleoresin defense of conifers produced by diterpene synthases and cytochrome P450s of the CYP720B family. The evolution of DRA metabolism shares common origins with the biosynthesis of ent-kaurenoic acid, which is highly conserved in general (primary) metabolism of gibberellin biosynthesis. Transcriptome mining in species of spruce (Picea) and pine (Pinus) revealed CYP720Bs of four distinct clades. We cloned a comprehensive set of 12 different Sitka spruce (Picea sitchensis) CYP720Bs as full-length cDNAs. Spatial expression profiles, methyl jasmonate induction, and transcript enrichment in terpenoid-producing resin ducts suggested a role of CYP720B4 in DRA biosynthesis. CYP720B4 was characterized as a multisubstrate, multifunctional enzyme by the formation of oxygenated diterpenoids in metabolically engineered yeast, yeast in vivo transformation of diterpene substrates, in vitro assays with CYP720B4 protein produced in Escherichia coli, and alteration of DRA profiles in RNA interference-suppressed spruce seedlings. CYP720B4 was active with 24 different diterpenoid substrates, catalyzing consecutive C-18 oxidations in the biosynthesis of an array of diterpene alcohols, aldehydes, and acids. CYP720B4 was most active in the formation of dehydroabietic acid, a compound associated with insect resistance of Sitka spruce. We identified patterns of convergent evolution of CYP720B4 in DRA metabolism and ent-kaurene oxidase CYP701 in gibberellin metabolism and revealed differences in the evolution of specialized and general diterpene metabolism in a gymnosperm. The genomic and functional characterization of the gymnosperm CYP720B family highlights that the evolution of specialized metabolism involves substantial diversification relative to conserved, general metabolism. PMID:21994349

  20. Evolution of diterpene metabolism: Sitka spruce CYP720B4 catalyzes multiple oxidations in resin acid biosynthesis of conifer defense against insects.

    Science.gov (United States)

    Hamberger, Björn; Ohnishi, Toshiyuki; Hamberger, Britta; Séguin, Armand; Bohlmann, Jörg

    2011-12-01

    Diterpene resin acids (DRAs) are specialized (secondary) metabolites of the oleoresin defense of conifers produced by diterpene synthases and cytochrome P450s of the CYP720B family. The evolution of DRA metabolism shares common origins with the biosynthesis of ent-kaurenoic acid, which is highly conserved in general (primary) metabolism of gibberellin biosynthesis. Transcriptome mining in species of spruce (Picea) and pine (Pinus) revealed CYP720Bs of four distinct clades. We cloned a comprehensive set of 12 different Sitka spruce (Picea sitchensis) CYP720Bs as full-length cDNAs. Spatial expression profiles, methyl jasmonate induction, and transcript enrichment in terpenoid-producing resin ducts suggested a role of CYP720B4 in DRA biosynthesis. CYP720B4 was characterized as a multisubstrate, multifunctional enzyme by the formation of oxygenated diterpenoids in metabolically engineered yeast, yeast in vivo transformation of diterpene substrates, in vitro assays with CYP720B4 protein produced in Escherichia coli, and alteration of DRA profiles in RNA interference-suppressed spruce seedlings. CYP720B4 was active with 24 different diterpenoid substrates, catalyzing consecutive C-18 oxidations in the biosynthesis of an array of diterpene alcohols, aldehydes, and acids. CYP720B4 was most active in the formation of dehydroabietic acid, a compound associated with insect resistance of Sitka spruce. We identified patterns of convergent evolution of CYP720B4 in DRA metabolism and ent-kaurene oxidase CYP701 in gibberellin metabolism and revealed differences in the evolution of specialized and general diterpene metabolism in a gymnosperm. The genomic and functional characterization of the gymnosperm CYP720B family highlights that the evolution of specialized metabolism involves substantial diversification relative to conserved, general metabolism.

  1. Cheese intake lowers plasma cholesterol concentrations without increasing bile acid excretion

    Directory of Open Access Journals (Sweden)

    Julie B. Hjerpsted

    2016-03-01

    Conclusion: We were not able to confirm the hypothesis that calcium from cheese increases the excretion of fecal bile acids. Therefore, the mechanisms responsible for the lowering of cholesterol concentrations with cheese compared to butter intake remains unresolved.

  2. Using Simple Quadratic Equations to Estimate Equilibrium Concentrations of an Acid

    Science.gov (United States)

    Brilleslyper, Michael A.

    2004-01-01

    Application of quadratic equations to standard problem in chemistry like finding equilibrium concentrations of ions in an acid solution is explained. This clearly shows that pure mathematical analysis has meaningful applications in other areas as well.

  3. Modularity of Conifer Diterpene Resin Acid Biosynthesis: P450 Enzymes of Different CYP720B Clades Use Alternative Substrates and Converge on the Same Products.

    Science.gov (United States)

    Geisler, Katrin; Jensen, Niels Berg; Yuen, Macaire M S; Madilao, Lina; Bohlmann, Jörg

    2016-05-01

    Cytochrome P450 enzymes of the CYP720B subfamily play a central role in the biosynthesis of diterpene resin acids (DRAs), which are a major component of the conifer oleoresin defense system. CYP720Bs exist in families of up to a dozen different members in conifer genomes and fall into four different clades (I-IV). Only two CYP720B members, loblolly pine (Pinus taeda) PtCYP720B1 and Sitka spruce (Picea sitchensis) PsCYP720B4, have been characterized previously. Both are multisubstrate and multifunctional clade III enzymes, which catalyze consecutive three-step oxidations in the conversion of diterpene olefins to DRAs. These reactions resemble the sequential diterpene oxidations affording ent-kaurenoic acid from ent-kaurene in gibberellin biosynthesis. Here, we functionally characterized the CYP720B clade I enzymes CYP720B2 and CYP720B12 in three different conifer species, Sitka spruce, lodgepole pine (Pinus contorta), and jack pine (Pinus banksiana), and compared their activities with those of the clade III enzymes CYP720B1 and CYP720B4 of the same species. Unlike the clade III enzymes, clade I enzymes were ultimately found not to be active with diterpene olefins but converted the recently discovered, unstable diterpene synthase product 13-hydroxy-8(14)-abietene. Through alternative routes, CYP720B enzymes of both clades produce some of the same profiles of conifer oleoresin DRAs (abietic acid, neoabietic acid, levopimaric acid, and palustric acid), while clade III enzymes also function in the formation of pimaric acid, isopimaric acid, and sandaracopimaric acid. These results highlight the modularity of the specialized (i.e. secondary) diterpene metabolism, which produces conifer defense metabolites through variable combinations of different diterpene synthase and CYP720B enzymes. © 2016 American Society of Plant Biologists. All Rights Reserved.

  4. Organosulfates and organic acids in Arctic aerosols: speciation, annual variation and concentration levels

    Science.gov (United States)

    Hansen, A. M. K.; Kristensen, K.; Nguyen, Q. T.; Zare, A.; Cozzi, F.; Nøjgaard, J. K.; Skov, H.; Brandt, J.; Christensen, J. H.; Ström, J.; Tunved, P.; Krejci, R.; Glasius, M.

    2014-02-01

    Sources, composition and occurrence of secondary organic aerosols (SOA) in the Arctic were investigated at Zeppelin Mountain, Svalbard, and Station Nord, northeast Greenland, during the full annual cycle of 2008 and 2010 respectively. We focused on the speciation of three types of SOA tracers: organic acids, organosulfates and nitrooxy organosulfates from both anthropogenic and biogenic precursors, here presenting organosulfate concentrations and compositions during a full annual cycle and chemical speciation of organosulfates in Arctic aerosols for the first time. Aerosol samples were analysed using High Performance Liquid Chromatography coupled to a quadrupole Time-of-Flight mass spectrometer (HPLC-q-TOF-MS). A total of 11 organic acids (terpenylic acid, benzoic acid, phthalic acid, pinic acid, suberic acid, azelaic acid, adipic acid, pimelic acid, pinonic acid, diaterpenylic acid acetate (DTAA) and 3-methyl-1,2,3-butanetricarboxylic acid (MBTCA)), 12 organosulfates and one nitrooxy organosulfate were identified at the two sites. Six out of the 12 organosulfates are reported for the first time. Concentrations of organosulfates follow a distinct annual pattern at Station Nord, where high concentration were observed in late winter and early spring, with a mean total concentration of 47 (±14) ng m-3, accounting for 7 (±2)% of total organic matter, contrary to a considerably lower organosulfate mean concentration of 2 (±3) ng m-3 (accounting for 1 (±1)% of total organic matter) observed during the rest of the year. The organic acids followed the same temporal trend as the organosulfates at Station Nord; however the variations in organic acid concentrations were less pronounced, with a total mean organic acid concentration of 11.5 (±4) ng m-3 (accounting for 1.7 (±0.6)% of total organic matter) in late winter and early spring, and 2.2 (±1) ng m-3 (accounting for 0.9 (±0.4)% of total organic matter) during the rest of the year. At Zeppelin Mountain

  5. Gold Loading on Ion Exchange Resins in Non-Ammoniacal Resin-Solution Systems

    Directory of Open Access Journals (Sweden)

    Abrar Muslim

    2010-12-01

    Full Text Available The loading of gold using strong base anion exchange resin in non-ammoniac resin-solution (NARS systems has been studied. The loading of gold onto ion exchange resins is affected by polythionate concentration, and trithionate can be used as the baseline in the system. The results also show that resin capacity on gold loading increases due to the increase in the equilibrium thiosulfate concentration in the NARS system. Gold loading performances show the need of optimization the equilibrium concentrations of thiosulfate in the NARS system. Keywords: equilibrium, gold loading, resin capacity, thiosulfate, trithionate

  6. Removal of CdTe in acidic media by magnetic ion-exchange resin: A potential recycling methodology for cadmium telluride photovoltaic waste

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Teng, E-mail: zhangteng@mail.iee.ac.cn; Dong, Zebin; Qu, Fei; Ding, Fazhu; Peng, Xingyu; Wang, Hongyan; Gu, Hongwei

    2014-08-30

    Highlights: • Sulfonated magnetic microsphere was prepared as one strong acid cation-exchange resin. • Cd and Te can be removed directly from the highly acidic leaching solution of CdTe. • Good chemical stability, fast adsorbing rate and quick magnetic separation in strong acidic media. • A potential path for recycling CdTe photovoltaic waste. - Abstract: Sulfonated magnetic microspheres (PSt-DVB-SNa MPs) have been successfully prepared as adsorbents via an aqueous suspension polymerization of styrene-divinylbenzene and a sulfonation reaction successively. The resulting adsorbents were confirmed by means of Fourier transform infrared spectra (FT-IR), X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope equipped with an energy dispersive spectrometer (SEM-EDS) and vibrating sample magnetometer (VSM). The leaching process of CdTe was optimized, and the removal efficiency of Cd and Te from the leaching solution was investigated. The adsorbents could directly remove all cations of Cd and Te from a highly acidic leaching solution of CdTe. The adsorption process for Cd and Te reached equilibrium in a few minutes and this process highly depended on the dosage of adsorbents and the affinity of sulfonate groups with cations. Because of its good adsorption capacity in strong acidic media, high adsorbing rate, and efficient magnetic separation from the solution, PSt-DVB-SNa MPs is expected to be an ideal material for the recycling of CdTe photovoltaic waste.

  7. Nitrogen balance, plasma free amino acid concentrations and urinary orotic acid excretion during long-term fasting in cats.

    Science.gov (United States)

    Biourge, V; Groff, J M; Fisher, C; Bee, D; Morris, J G; Rogers, Q R

    1994-07-01

    The purpose of this study was to ascertain the changes in nitrogen balance, plasma free amino acid concentrations, urinary orotic acid excretion and body weight during long-term fasting in adult obese cats. Results from eight cats that fasted rather than eat an unpalatable diet are reported. After 5 to 6 wk of weight loss, six of the eight cats developed signs of hepatic lipidosis, and the livers of all cats were severely infiltrated with lipids. Cats lost (mean +/- SE) 33.2 +/- 1.4% of their pre-fasting body weight. Mean nitrogen balance (+/- SE) was -547 +/- 54 mg.d-1.kg-2/3 for the first week, and then the net nitrogen losses decreased to a plateau (-303 +/- 52 mg.d-1.kg-2/3) after 4 wk. Fasting was associated with a decrease in plasma concentration of essential amino acids. When plasma amino acid concentrations were considered individually, concentrations of alanine, methionine, taurine, citrulline, arginine and tryptophan decreased the most (> or = 50%), whereas concentrations of glutamine, glutamate and ornithine significantly increased. Orotic acid was not detected in the urine during the fast. After 1 wk of fasting, obese cats had reduced nitrogen excretion, but not to the same extent as has been shown in obese humans or obese rats. It is suggested that the availability of several amino acids may become limiting for liver protein synthesis during fasting and that these deficiencies may contribute to the development of hepatic lipidosis. Orotic acid was not linked to hepatic lipidosis caused by fasting in cats.

  8. Peripartum cardiomyopathy is associated with increased uric acid concentrations: A population based study.

    Science.gov (United States)

    Sagy, Iftach; Salman, Amjad Abu; Kezerle, Louise; Erez, Offer; Yoel, Idan; Barski, Leonid

    Peri-partum cardiomyopathy (PPCM) is a clinical heart failure that usually develops during the final stage of pregnancy or the first months following delivery. High maternal serum uric acid concentrations have been previous associated with heart failure and preeclampsia. 1) To explored the clinical characteristics of PPCM patients; and 2) to determine the association between maternal serum uric acid concentrations and PPCM. This is a retrospective population based case control study. Cases and controls were matched 1:4 (for gestational age, medical history of cardiac conditions and creatinine); conditional logistic regression was used to identify clinical parameters that were associated with PPCM. The prevalence of peripartum cardiomyopathy at our institution was 1-3832 deliveries (42/160,964). In a matched multivariate analysis high maternal serum uric acid concentrations were associated with PPCM (O.R 1.336, 95% C.I 1.003-1.778). Uric acid concentrations were higher within the Non-Jewish patients and mothers of male infant with PPCM in compare to those without PPCM (p value 0.003 and 0.01 respectively). PPCM patients had increased maternal serum uric acid concentrations. This observation aligns with previous report regarding the increased uric acid concentration in women with preeclampsia and congestive heart failure, suggestive of a common underlying mechanism that mediates the myocardial damage. Copyright © 2017 Elsevier Inc. All rights reserved.

  9. Effect of sodium hypochlorite and peracetic acid on the surface roughness of acrylic resin polymerized by heated water for short and long cycles.

    Science.gov (United States)

    Sczepanski, Felipe; Sczepanski, Claudia Roberta Brunnquell; Berger, Sandrine Bittencourt; Consani, Rafael Leonardo Xediek; Gonini-Júnior, Alcides; Guiraldo, Ricardo Danil

    2014-10-01

    To evaluate the surface roughness of acrylic resin submitted to chemical disinfection via 1% sodium hypochlorite (NaClO) or 1% peracetic acid (C2H4O3). The disc-shaped resin specimens (30 mm diameter ×4 mm height) were polymerized by heated water using two cycles (short cycle: 1 h at 74°C and 30 min at 100°C; conventional long cycle: 9 h at 74°C). The release of substances by these specimens in water solution was also quantified. Specimens were fabricated, divided into four groups (n = 10) depending on the polymerization time and disinfectant. After polishing, the specimens were stored in distilled deionized water. Specimens were immersed in 1% NaClO or 1% C2H4O3 for 30 min, and then were immersed in distilled deionized water for 20 min. The release of C2H4O3 and NaClO was measured via visual colorimetric analysis. Roughness was measured before and after disinfection. Roughness data were subjected to two-way ANOVA and Tukey's test. There was no interaction between polymerization time and disinfectant in influencing the average surface roughness (Ra, P = 0.957). Considering these factors independently, there were significant differences between short and conventional long cycles (P = 0.012), but no significant difference between the disinfectants hypochlorite and C2H4O3 (P = 0.366). Visual colorimetric analysis did not detect release of substances. It was concluded that there was the difference in surface roughness between short and conventional long cycles, and disinfection at acrylic resins polymerized by heated water using a short cycle modified the properties of roughness.

  10. Effects of Oral Glucosamine Hydrochloride Administration on Plasma Free Amino Acid Concentrations in Dogs

    Directory of Open Access Journals (Sweden)

    Saburo Minami

    2011-04-01

    Full Text Available We examined the effects of oral glucosamine hydrochloride (GlcN, N-acetyl-D-glucosamine (GlcNAc and D-glucose (Glc administration on plasma total free amino acid (PFAA concentrations in dogs. The PFAA concentrations increased in the control group and the GlcNAc group at one hour after feeding, and each amino acid concentration increased. On the other hand, in the GlcN group and the Glc group PFAA concentrations decreased at one hour after feeding. A significant decrease in amino acid concentration was observed for glutamate, glycine and alanine. Our results suggest the existence of differences in PFAA dynamics after oral administration of GlcN and GlcNAc in dogs.

  11. Dissolution behaviour of freibergite-tetrahedrite concentrate in acidic dichromate solution

    Directory of Open Access Journals (Sweden)

    Sh Nyamdelger

    2014-10-01

    Full Text Available Asgat ore sample with estimated content of 431g/t silver was concentrated by using floatation method and obtained freibergite-tetrahedrite concentrate with 9050g/t Ag, 35.75% Cu, 28.5% Sb and 10.6% Fe, respectively. The dissolution of concentrate in acidic potassium dichromate solution has been investigated with respect to the sulfuric acid and potassium dichromate concentrations and by changing leaching temperature and time. Leaching freibergitetetrahedrite concentrate in dichromate acidic solution (K2Cr2O7-0.1M, H2SO4-0.4M leaching time 4h, leaching temperature 95°С resulted total amount of leaching of 95.65 % silver, 93.85% copper, 99.86 % antimony and 30.18% iron. DOI: http://dx.doi.org/10.5564/mjc.v14i0.196 Mongolian Journal of Chemistry 14 (40, 2013, p36-40

  12. Effect of citric acid concentration and hydrolysis time on physicochemical properties of sweet potato starches.

    Science.gov (United States)

    Surendra Babu, Ayenampudi; Parimalavalli, Ramanathan; Rudra, Shalini Gaur

    2015-09-01

    Physicochemical properties of citric acid treated sweet potato starches were investigated in the present study. Sweet potato starch was hydrolyzed using citric acid with different concentrations (1 and 5%) and time periods (1 and 11 h) at 45 °C and was denoted as citric acid treated starch (CTS1 to CTS4) based on their experimental conditions. The recovery yield of acid treated starches was above 85%. The CTS4 sample displayed the highest amylose (around 31%) and water holding capacity its melting temperature was 47.66 °C. The digestibility rate was slightly increased for 78.58% for the CTS3 and CTS4. The gel strength of acid modified starches ranged from 0.27 kg to 1.11 kg. RVA results of acid thinned starches confirmed a low viscosity profile. CTS3 starch illustrated lower enthalpy compared to all other modified starches. All starch samples exhibited a shear-thinning behavior. SEM analysis revealed that the extent of visible degradation was increased at higher hydrolysis time and acid concentration. The CTS3 satisfied the criteria required for starch to act as a fat mimetic. Overall results conveyed that the citric acid treatment of sweet potato starch with 5% acid concentration and 11h period was an ideal condition for the preparation of a fat replacer. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. Association between the blood concentrations of ammonia and carnitine/amino acid of schizophrenic patients treated with valproic acid.

    Science.gov (United States)

    Ando, Masazumi; Amayasu, Hideaki; Itai, Takahiro; Yoshida, Hisahiro

    2017-01-01

    Administration of valproic acid (VPA) is complicated with approximately 0.9% of patients developing hyperammonemia, but the pathogenesis of this adverse effect remains to be clarified. The aim of the present study was to search for mechanisms associated with VPA-induced hyperammonemia in the light of changes in serum amino acids concentrations associated with the urea cycle of schizophrenic patients. Blood samples (10 mL) were obtained from 37 schizophrenic patients receiving VPA for the prevention of violent behaviors in the morning after overnight fast. Blood concentrations of ammonia, VPA, free carnitine, acyl-carnitine, and 40 amino acids including glutamate and citrulline were measured for each patient. Univariate and multivariate regression analyses were performed to identify amino acids or concomitantly administered drugs that were associated with variability in the blood concentrations of ammonia. The blood ammonia level was positively correlated with the serum glutamate concentration ( r  = 0.44, p  blonanserin ( p  < 0.01) was positively associated with the elevation of the blood ammonia level. We hypothisized that VPA would elevate the blood ammonia level of schizophrenic patients. The observed changes in serum amino acids are compatible with urea cycle dysfunction, possibly due to reduced carbamoyl-phosphate synthase 1 (CPS1) activity. We conclude that VPA should be prudently prescribed to schizophrenic patients, particularly those receiving mood stabilizers or certain antipsychotics.

  14. Time-dependent changes in the plasma amino acid concentration in diabetes mellitus.

    Science.gov (United States)

    Mochida, Taiga; Tanaka, Takayuki; Shiraki, Yasuko; Tajiri, Hiroko; Matsumoto, Shirou; Shimbo, Kazutaka; Ando, Toshihiko; Nakamura, Kimitoshi; Okamoto, Masahiro; Endo, Fumio

    2011-08-01

    We investigated longitudinal change in the amino acid (AA) profile in type 1 diabetes mellitus (DM) using AKITA mice, which develop DM as a result of insulin deficiency. The plasma concentrations of valine, leucine, isoleucine, as well as the total branched chain amino acids, alanine, citrulline and proline, were significantly higher in the diabetic mice. We show that the degree and timing of the changes were different among the plasma amino acid concentrations (pAAs) during the development of type 1 DM. Copyright © 2011 Elsevier Inc. All rights reserved.

  15. Plastic casting resin poisoning

    Science.gov (United States)

    Epoxy poisoning; Resin poisoning ... Epoxy and resin can be poisonous if they are swallowed or their fumes are breathed in. ... Plastic casting resins are found in various plastic casting resin products.

  16. Resistance to fracture of endodontically treated premolars restored with glass ionomer cement or acid etch composite resin: An in vitro study

    Directory of Open Access Journals (Sweden)

    B Ranga

    2010-01-01

    Full Text Available Aim: Due to the weakness of endodontically treated posterior teeth requires more strengthened restoration to withstand occlusal forces. The purpose of the present study was to determine and compare the resistance to fracture of endodontically treated maxillary 1 st premolars restored with different materials in mesio-occluso-distal (MOD cavity preparations. Materials and Methods: MOD cavity preparations in 80 endodontically treated maxillary 1 st premolars were restored using four different methods. Fiber rings were filled with stone plaster and the teeth were placed into the plaster up to the level of cemento-enamel junction. The teeth were grouped according to restorative method, mounted in an Instrom T.T. machine, and the buccal walls subjected to a slowly increasing compressive force until fracture occurred. Result: The force of fracture of the walls of each tooth was recorded and the results in the various groups compared. All teeth fractured in a similar manner irrespective of the restorative method used. Conclusion: The resistance to the fracture of the teeth was the same when they were stored with glass ionomer cement as a base over which composite resin was placed. When the entire cavities were filled with glass ionomer cement, the resistance to fracture of the teeth decreased significantly compared with the acid etch resin technique.

  17. Leaf oil and resin acid components of lacebark pine, pinus bungeana zucc. Shiromatsu no ha no seiyu oyobi jushi san seibun

    Energy Technology Data Exchange (ETDEWEB)

    Ueda, Nasuo; Dewa, Naoyuki; Tsuneya, Tomoyuki (Tottori Univ., Tottori (Japan). Faculty of General Education); Kageyama, Mikiko; Nakajima, Akira; Yamamoto, Jiro; Nakajima, Ruka (Shiono Koryo Co. Ltd., Osaka (Japan))

    1989-11-30

    This study had the objective to search for the leafoil component of lacebark pine (Pinus bungeana Zucc), compare it with those of several other pines and Sciadopitys verillata Sieb, et Zucc whose fragrance comparatively resembles that of lacebark pine, and clarify the difference of fragrance. In addition, with regard to the resin acid component of resin, its comparison with those of red pine and black pine was made, and furthermore, in order to clarify the feature of the fragrance of lacebark pine, comparison by the enfleurage method was made with red pine, black pine and the above Sciadopitys. The leaf oils were extracted by steam distillation on the basis of making the extraction conditions such as the amount of samples, distillation time, and the amount of distillate, etc. as same as possible. As a result, with regard to the yield of the oil obtained by steam distillation, lacebark pine {prime} s was extremely big and almost twice more than those of black pine and red pine. Concerning the oil component, lacebark pine showed especially high contents of {alpha} -thujene, {alpha} -pinene and camphene and high contents of {beta} -caryophyllene and germacrene-D. Black pine had much of pinene and red pine had much of myrcene, etc. 21 refs., 2 figs., 4 tabs.

  18. Rheology of dilute acid hydrolyzed corn stover at high solids concentration

    Science.gov (United States)

    M.R. Ehrhardt; T.O. Monz; T.W. Root; R.K. Connelly; Tim Scott; D.J. Klingenberg

    2010-01-01

    The rheological properties of acid hydrolyzed corn stover at high solids concentration (20–35 wt.%) were investigated using torque rheometry. These materials are yield stress fluids whose rheological properties can be well represented by the Bingham model. Yield stresses increase with increasing solids concentration and decrease with increasing hydrolysis reaction...

  19. Relationships between fruit nutrients and concentrations of flavonoids and chlorogenic acid in 'Elstar' apple skin

    NARCIS (Netherlands)

    Awad, M.A.; Jager, de A.

    2002-01-01

    The relationships between fruit N, P, K, Mg and Ca concentrations during the season and flavonoid and chlorogenic acid concentrations in skin of `Elstar¿ apples at maturity have been studied during three seasons in a nutrition experiment (with the mutant `Elshof¿), and in a separate experiment with

  20. Critical phenomena in ethylbenzene oxidation in acetic acid solution at high cobalt(II) concentrations

    NARCIS (Netherlands)

    Gavrichkov, AA; Zakharov, [No Value

    Critical phenomena in ethylbenzene oxidation in an acetic acid solution at high cobalt(ill) concentrations (from 0.01 to 0.2 mol L-1) were studied at 60-90 degrees C by the gasometric (O-2 absorption), spectrophotometric (Co-III accumulation), and chemiluminescence (relative concentration of radical

  1. Influence of zirconium ion concentration in model extraction systems TBP - diluents - Zr+4 - nitric acid

    International Nuclear Information System (INIS)

    Rogoz, F.; Tlalka, M.

    1987-07-01

    In systems containing TBP, MBP, DBP and 1-butanol stable emulsions and precipitates are formed which separation is difficult in certain domain of concentration in zirconium ions. MPB and DBP increase stability of primary emulsion in kerosen and carbon tetrachloride but for different concentrations of nitric acid. Addition of 1-butanol decreases slightly the stability of primary emulsion [fr

  2. Serum uric acid concentrations are directly associated with the presence of benign multiple sclerosis.

    Science.gov (United States)

    Simental-Mendía, Esteban; Simental-Mendía, Luis E; Guerrero-Romero, Fernando

    2017-09-01

    It has been reported that patients with multiple sclerosis (MS) exhibit lower serum uric acid levels; however, the association between uric acid concentrations and benign MS (BMS) has not been assessed. Hence, the objective of the present study was to determine whether the serum concentrations of uric acid are associated with the presence of BMS. Men and non-pregnant women over 16 years of age with diagnosis of MS were enrolled in a cross-sectional study. Expanded Disability Status Scale score acid were exclusion criteria. According to subtype of disease, the eligible patients were allocated into groups with BMS and other varieties of MS. A logistic regression analysis was conducted in order to evaluate the association between serum concentrations of uric acid and BMS. A total of 106 patients were included, 39 in the group with BMS and 67 in the group with other varieties of MS. The logistic regression analysis adjusted by age, sex, and disease duration showed that increased concentrations of uric acid, indeed within the physiological levels, are significantly associated with the presence of BMS (OR = 2.60; 95% CI: 1.55-4.38, p uric acid, indeed within the physiological range, are likely linked to the presence of BMS.

  3. Influence of phytic acid concentration on performance of phytic acid conversion coatings on the AZ91D magnesium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Cui Xiufang [School of Materials Science and Chemical Engineering, Harbin Engineering University, 145 Nantong Street, Harbin 150001 (China); State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, 62 Wencui Road, Shenyang 110016 (China)], E-mail: cuixf97721@yahoo.com.cn; Li Ying [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, 62 Wencui Road, Shenyang 110016 (China); Li Qingfen; Jin Guo; Ding Minghui [School of Materials Science and Chemical Engineering, Harbin Engineering University, 145 Nantong Street, Harbin 150001 (China); Wang Fuhui [School of Materials Science and Chemical Engineering, Harbin Engineering University, 145 Nantong Street, Harbin 150001 (China); State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, 62 Wencui Road, Shenyang 110016 (China)

    2008-10-15

    In this study, the phytic acid conversion coating, a new environmentally friendly chemical protective coating for magnesium alloys, was prepared. The influences of phytic acid concentration on the formation process, microstructure, chemical state and corrosion resistance of the conversion coatings on AZ91D magnesium alloy were investigated by means of weight gain measurement, field-emission scanning electron microscopy (FESEM), Fourier transform infrared (FTIR) spectroscopy, potentiodynamic polarization method and electrochemical impedance spectroscopy (EIS), respectively. And the depth profile of all elements in the optimal conversion coatings was analyzed by auger electron spectroscopy (AES). The results show that the growth, microstructure, chemical state and corrosion resistance of the conversion coatings are all obviously affected by the phytic acid concentration. The concentration of 5 g l{sup -1} corresponds to the maximum weight gain. The main elements of the coating are Mg, Al, O, P, and C, which are distributed gradually in depth. The functional groups of conversion coatings formed in higher concentration phytic acid solution are closer to the constituent of phytic acid than those formed in lower concentration phytic acid solution. The coatings formed in 1-5 g l{sup -1} are integrated and uniform. However, those formed in 20-50 g l{sup -1} have some micro-cracks on the {alpha} phase. The coating formed in 5 g l{sup -1} has the best corrosion resistance, whose open circuit current density decreases about six orders than that of the untreated sample, although the coatings deposited in 1-20 g l{sup -1} can all improve the corrosion resistance of AZ91D.

  4. EFFECT OF ETCHING TIME AND ACID CONCENTRATION ON MICROMORPHOLOGICAL CHANGES IN DENTIN OF BOTH DENTITIONS

    Directory of Open Access Journals (Sweden)

    Natalia Gateva

    2016-04-01

    Full Text Available Aim: to compare micro morphological changes in primary and permanent dentin after etching with phosphoric acid (20% and 37,5% for 7 and 15 sec. by SEM. Material and methods: The study included 42 primary and permanent teeth, divided into 8 groups by etching time and acid concentration. Enamel and dentin were removed from the vestibular area and after the expiration of etching time samples were washed with water-air stream and dried with light airflow. From each sample 10 magnified images were made from central vestibular area. The cleaning effect was measured in percentage, as a ratio between the numbers of uncleaned tubules to the total tubules. Results were analyzed with One-way and MANOVA. Post hoc Multiple Comparisons test – SPSS 19 was applied. Results: The proportion of uncleaned tubules in primary teeth was higher than that of permanent teeth at acid concentration of 20%. At a concentration of 37.5% this relationship is reversed. At 7 sec there was a bigger difference between the share of uncleaned tubules for primary and permanent teeth, while at 15 sec this difference virtually disappears. The difference in the proportion of uncleaned tubules between the two acid concentrations at 7 seconds etching is significantly greater compared to the same difference between the two acid concentrations by etching for 15 sec. Conclusion: Effectively removed smear layer and no precipitate was observed in primary teeth even at 7 seconds etching with 37.5% acid.

  5. Alterations in serum amino acid concentrations in dogs with protein-losing enteropathy.

    Science.gov (United States)

    Kathrani, Aarti; Allenspach, Karin; Fascetti, Andrea J; Larsen, Jennifer A; Hall, Edward J

    2018-03-31

    Certain amino acids are decreased in humans with inflammatory bowel disease (IBD) and supplementation with the same amino acids has shown beneficial effects in animal models of IBD. Currently, the amino acid status of dogs with protein-losing enteropathy (PLE) is unknown. To determine if serum amino acid concentrations are abnormal in dogs with PLE and correlated with clinical and laboratory variables and outcome. Thirty client-owned dogs diagnosed with PLE and 12 apparently healthy dogs seen at Bristol Veterinary School. Retrospective study using stored residual serum from fasted dogs with PLE, collected at the time of diagnostic investigation and from apparently healthy dogs. Serum was analyzed for 30 amino acids using an automated high-performance liquid chromatography amino acid analyzer. Serum tryptophan concentrations were significantly decreased in dogs with PLE (median, 22 nmol/mL; range, 1-80 nmol/mL) compared with apparently healthy control dogs (median, 77.5 nmol/mL; range, 42-135 nmol/mL, P PLE and apparently healthy. Serum tryptophan concentrations were also significantly correlated with serum albumin concentrations in dogs with PLE (P = .001, R 2 = 0.506). Decreased serum tryptophan concentration might play a role in the pathogenesis of canine PLE or be a consequence of the disease. © 2018 The Authors. Journal of Veterinary Internal Medicine published by Wiley Periodicals, Inc. on behalf of the American College of Veterinary Internal Medicine.

  6. THE EFFECTS OF ANIMAL AGE AND ACETIC ACID CONCENTRATION ON PIGSKIN GELATIN CHARACTERISTICS

    Directory of Open Access Journals (Sweden)

    Y. Pranoto

    2012-09-01

    Full Text Available This research was aimed to study the influence of animal age and concentration of the acetic acid solution on physical and chemical properties of pigskin gelatin. The experiment used Completely Randomized Design (CRD with two factors. The first factor was animal age consisted of 3 levels (5, 7 and 9 months. The second factor was concentration of acetic acid solution consisted of 3 levels (2, 4 and 6 percents. The result showed that animal age had significant effect (P0.05 on the yields, gel strength, viscosity, protein content and pH value. It was concluded that pigskin gelatin from ages of 5, 7 and 9 months and acetic acid concentration of 2, 4 and 6% had similar characteristics to the commercial gelatin, but the optimum production of gelatin was combination of pigskin gelatin from 7 months and of 2% acetic acid.

  7. Cheese intake lowers plasma cholesterol concentrations without increasing bile acid excretion

    DEFF Research Database (Denmark)

    Hjerpsted, Julie Bousgaard; Dragsted, Lars Ove; Tholstrup, Tine

    2016-01-01

    Purpose Cheese is a dairy product with high calcium content. It has been suggested that calcium intake may increase fecal excretion of bile acids that would cause a regeneration of bile acids from hepatic cholesterol and thereby result in a lowering of plasma cholesterol concentrations. We aimed...... with 13% energy from cheese or butter. Results After 6 weeks of intervention cheese resulted in higher amounts of calcium excreted in feces compared to butter. However, no difference was observed in fecal bile acid output despite lower serum total, LDL and HDL cholesterol concentrations observed...... with cheese intake. Conclusion We were not able to confirm the hypothesis that calcium from cheese increases the excretion of fecal bile acids. Therefore, the mechanisms responsible for the lowering of cholesterol concentrations with cheese compared to butter intake remains unresolved....

  8. Influence of concentration in phosphoric acid treatment of titanium oxide and their powder properties

    Directory of Open Access Journals (Sweden)

    Hiroaki Onoda

    2015-03-01

    Full Text Available Titanium oxide that has the photocatalytic activity is used as a white pigment for cosmetics. A certain degree of sebum on the skin is decomposed by the ultraviolet radiation in sunlight. In this work, titanium oxide was shaken with various concentrations of phosphoric acid to synthesize a novel white pigment for cosmetics. Their chemical composition, powder properties, photocatalytic activity, color phase, and smoothness were studied. The obtained materials indicated XRD peaks of titanium oxide; however, these peak intensities became weak by phosphoric acid treatment. The photocatalytic activity of the obtained powders became weak by phosphoric acid treatment to protect the sebum on the skin. The high concentration of phosphoric acid was suitable to obtain a novel white pigment in the phosphoric acid treatment of titanium oxide.

  9. Secular trend of serum docosahexaenoic acid, eicosapentaenoic acid, and arachidonic acid concentrations among Japanese-a 4- and 13-year descriptive epidemiologic study.

    Science.gov (United States)

    Otsuka, Rei; Kato, Yuki; Imai, Tomoko; Ando, Fujiko; Shimokata, Hiroshi

    2015-03-01

    Cross-sectional studies have shown age-related increases in blood docosahexaenoic and eicosapentaenoic acid and decreases in arachidonic acid. We describe serum docosahexaenoic, eicosapentaenoic, and arachidonic acid concentrations over 13 years (1997-2012) across four study waves and serum fatty acid composition over 4 years (2006-2012) between two study waves according to age groups by sex in the same subjects. We included 443 men and 435 women aged 40-79 years at baseline. Serum arachidonic acid concentrations increased in all sex and age groups over 13 years, and eicosapentaenoic or docosahexaenoic acid concentrations increased in males and females who were younger and middle-aged at baseline. Only serum arachidonic acid composition increased over 4 years in men and women who were 40-69 years at baseline, even after adjustment for arachidonic acid intake. These findings suggest a secular increase trend in serum arachidonic acid levels over 13 years among randomly selected community-dwelling middle-aged and elderly Japanese. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Resin composites

    DEFF Research Database (Denmark)

    Benetti, Ana Raquel; Peutzfeldt, Anne; Lussi, Adrian

    2014-01-01

    OBJECTIVE: To investigate how the modulus of elasticity of resin composites influences marginal quality in restorations submitted to thermocyclic and mechanical loading. METHODS: Charisma, Filtek Supreme XTE and Grandio were selected as they were found to possess different moduli of elasticity...... of resin composite (p=0.81) on the quality of dentine margins was observed, before or after loading. Deterioration of all margins was evident after loading (p....008). CONCLUSIONS: The resin composite with the highest modulus of elasticity resulted in the highest number of gap-free enamel margins but with an increased incidence of paramarginal enamel fractures. CLINICAL SIGNIFICANCE: The results from this study suggest that the marginal quality of restorations can...

  11. An Engineering Evaluation of Spherical Resorcinol Formaldehyde Resin

    Energy Technology Data Exchange (ETDEWEB)

    Birdwell Jr, Joseph F [ORNL; Lee, Denise L [ORNL; Taylor, Paul Allen [ORNL; Collins, Robert T [ORNL; Hunt, Rodney Dale [ORNL

    2010-09-01

    , quantification of cesium adsorption performance as a function of operating temperature and pH, and evaluation of sodium uptake (titration) as function of pH and counteranion concentration. The results of these efforts are presented in this report. Hydraulic performance of the resin and the use of eluant alternatives to nitric acid have also been evaluated and have been reported elsewhere (Taylor 2009, Taylor and Johnson 2009).

  12. Microarray-based transcriptome of Listeria monocytogenes adapted to sublethal concentrations of acetic acid, lactic acid, and hydrochloric acid.

    Science.gov (United States)

    Tessema, Girum Tadesse; Møretrø, Trond; Snipen, Lars; Heir, Even; Holck, Askild; Naterstad, Kristine; Axelsson, Lars

    2012-09-01

    Listeria monocytogenes , an important foodborne pathogen, commonly encounters organic acids in food-related environments. The transcriptome of L. monocytogenes L502 was analyzed after adaptation to pH 5 in the presence of acetic acid, lactic acid, or hydrochloric acid (HCl) at 25 °C, representing a condition encountered in mildly acidic ready-to-eat food kept at room temperature. The acid-treated cells were compared with a reference culture with a pH of 6.7 at the time of RNA harvesting. The number of genes and magnitude of transcriptional responses were higher for the organic acids than for HCl. Protein coding genes described for low pH stress, energy transport and metabolism, virulence determinates, and acid tolerance response were commonly regulated in the 3 acid-stressed cultures. Interestingly, the transcriptional levels of histidine and cell wall biosynthetic operons were upregulated, indicating possible universal response against low pH stress in L. monocytogenes. The opuCABCD operon, coding proteins for compatible solutes transport, and the transcriptional regulator sigL were significantly induced in the organic acids, strongly suggesting key roles during organic acid stress. The present study revealed the complex transcriptional responses of L. monocytogenes towards food-related acidulants and opens the roadmap for more specific and in-depth future studies.

  13. Long term stability of cannabis resin and cannabis extracts

    DEFF Research Database (Denmark)

    Lindholst, Christian

    2010-01-01

    at room temperature, 4 °C and - 20 °C for up to 4 years. Acidic THC degrades exponentially via decarboxylation with concentration halve-lives of approximately 330 and 462 days in daylight and darkness, respectively. The degradation of neutral THC seems to occur somewhat slower. When cannabinoids were...... stored in extracted form at room temperature the degradation rate of acidic THC increased significantly relative to resin material with concentration halve-lives of 35 and 91 days in daylight and darkness, respectively. Once cannabis material is extracted into organic solvents, care should be taken...

  14. Root colonization by symbiotic arbuscular mycorrhizal fungi increases sesquiterpenic acid concentrations in Valeriana officinalis L.

    Science.gov (United States)

    Nell, Monika; Wawrosch, Christoph; Steinkellner, Siegrid; Vierheilig, Horst; Kopp, Brigitte; Lössl, Andreas; Franz, Chlodwig; Novak, Johannes; Zitterl-Eglseer, Karin

    2010-03-01

    In some medicinal plants a specific plant-fungus association, known as arbuscular mycorrhizal (AM) symbiosis, increases the levels of secondary plant metabolites and/or plant growth. In this study, the effects of three different AM treatments on biomass and sesquiterpenic acid concentrations in two IN VITRO propagated genotypes of valerian ( VALERIANA OFFICINALIS L., Valerianaceae) were investigated. Valerenic, acetoxyvalerenic and hydroxyvalerenic acid levels were analyzed in the rhizome and in two root fractions. Two of the AM treatments significantly increased the levels of sesquiterpenic acids in the underground parts of valerian. These treatments, however, influenced the biomass of rhizomes and roots negatively. Therefore this observed increase was not accompanied by an increase in yield of sesquiterpenic acids per plant. Furthermore, one of the two genotypes had remarkably high hydroxyvalerenic acid contents and can be regarded as a hydroxyvalerenic acid chemotype. Copyright Georg Thieme Verlag KG Stuttgart New York.

  15. Variability and determinants of wood dust and resin acid exposure during wood pellet production: measurement strategies and bias in assessing exposure-response relationships.

    Science.gov (United States)

    Hagström, Katja; Lundholm, Cecilia; Eriksson, Kare; Liljelind, Ingrid

    2008-11-01

    Production of wood pellets is a relatively new and expanding industry in which the exposure profiles differ from those in other wood-processing industries like carpentries and sawmills where there are lower levels of wood dust. Sixty-eight personal exposure measurements of wood dust (inhalable and total dust) and resin acids were collected for 44 participants at four production plants located in Sweden. Results were used to estimate within- and between-worker variability and to identify uniformly exposed groups and determinants of exposure. In addition, overexposure, whether the risk of the long-term mean exposure of a randomly selected worker exceeding the occupational exposure limit is acceptably low, was calculated as well as the underestimation of the exposure-response relationship (attenuation). Greater variability in exposure between work shifts than between workers was observed with the within-worker variation accounting for 57-99% of the total variance in the individual-based model. Several uniformly exposed groups were detected but were mostly associated with a between-worker variation of zero which is an underestimation of the between-worker variation but an indication of uniformly exposed groups. Cleaning was identified as a work task that increases exposure slightly; so reducing workers' exposure during this operation is advisable. The levels of wood dust were high and were found to pose unacceptable risks of overexposure at all plants for inhalable dust and at three out of four plants for total dust. These findings show that exposure to dust needs to be reduced in this industry. For resin acids, the exposure was classed as acceptable at all plants. According to an individual-based model constructed from the data, the level of attenuation was high, and thus there would be substantial bias in derived dose-response relationships.

  16. Wolframite Conversion in Treating a Mixed Wolframite-Scheelite Concentrate by Sulfuric Acid

    Science.gov (United States)

    Shen, Leiting; Li, Xiaobin; Zhou, Qiusheng; Peng, Zhihong; Liu, Guihua; Qi, Tiangui; Taskinen, Pekka

    2018-02-01

    Complete wolframite conversion in sulfuric acid is significant for expanding the applicability of the sulfuric acid method for producing ammonium paratungstate. In this paper, the conversion of wolframite in treating a mixed wolframite-scheelite concentrate by sulfuric acid was studied systematically. The results show that the conversion of wolframite in sulfuric acid is more difficult than that of scheelite, requiring rigorous reaction conditions. A solid H2WO4 layer forms on the surfaces of the wolframite particles and becomes denser with increasing H2SO4 concentration, thus hindering the conversion. Furthermore, the difficulty in wolframite conversion can be mainly attributed to the accumulation of Fe2+ (and/or Mn2+) in the H2SO4 solution, which can be solved by reducing Fe2+ (and/or Mn2+) concentration through oxidization and/or a two-stage process. Additionally, the solid converted product of the mixed wolframite-scheelite concentrate has an excellent leachability of tungsten in an aqueous ammonium carbonate solution at ambient temperature, with approximately 99% WO3 recovery. This work presents a route for manufacturing ammonium paratungstate by treating the mixed concentrate in sulfuric acid followed by leaching in ammonium carbonate solution.

  17. The concentration of free amino acids in blood serum of dairy cows with primary ketosis.

    Science.gov (United States)

    Marczuk, J; Brodzki, P; Brodzki, A; Kurek, Ł

    2018-03-01

    Ketosis is a common condition found in the initial stages of lactation in high-yielding dairy cows. The major cause of ketosis is a negative energy balance. During the energy deficiency, proteolysis processes develop parallel to lipolysis. During proteolysis, muscle tissue can be used as a source of amino acid. To date, the participation of amino acids in gluconeogenesis (glucogenic amino acids) and ketogenesis (ketogenic amino acids) has not been determined in detail. This paper presents the study on determination of the parameters of protein and free amino acid metabolism in blood serum of dairy cows with primary ketosis compared to healthy cows. This study contributes to better understanding of the role of amino acids in pathogenesis of ketosis. A total of 30 cows, divided into two groups: experimental (15 cows with ketosis) and control (15 healthy cows), were included in the study. The concentrations of glucose, β-hydroxybutyrate, total protein, albumin, urea, and free amino acids were determined in peripheral blood. Statistically significantly higher concentrations of glutamine, glutamic acid, isoleucine (p≤0.001), and tyrosine (p≤0.05) were found in cows with primary ketosis compared to healthy cows. Significant decrease in the concentrations of asparagine, histidine, methionine, and serine (p≤0.001), alanine, leucine, lysine and proline (p≤0.05) was observed. Significant increase of total ketogenic and glucogenic amino acids (p≤0.05), and an increased ratio of total ketogenic and glucogenic amino acids to total amino acids (p≤0.001) were noted in cows with ketosis. In our study, the changes, in particular observed in amino acid concentration in cows with primary ketosis, indicate its intensive use in both ketogenesis and gluconeogenesis processes. Therefore, a detailed understanding of the role that amino acids play in gluconeogenesis and ketogenesis will improve ketosis diagnostics and monitoring the course of a ketosis episode. Perhaps, the

  18. Decreased sugar concentration in vegetable and fruit juices by growth of functional lactic acid bacteria.

    Science.gov (United States)

    Ishii, Masaki; Matsumoto, Yasuhiko; Nishida, Satoshi; Sekimizu, Kazuhisa

    2017-03-22

    Leuconostoc carnosum #7-2, L. gelidum #4-2, and L. mesenteroides 8/11-3, which were isolated from fermented plant foods, are lactic acid bacteria. We previously reported that these bacteria are functional lactic acid bacteria whose innate immunity-stimulating activities are high based on a silkworm muscle contraction assay. The concentrations of these three lactic acid bacteria increased to more than 1 × 10 6 colony forming units (cfu)/mL in various vegetable and fruit juices when the pH values were appropriately adjusted. As the bacteria grew in the vegetable and fruit juices, the pH decreased and the concentrations of total sugars and glucose also decreased. These findings suggest that these functional lactic acid bacteria can be used to produce vegetable and fruit juices with reduced sugar levels, which is expected to be beneficial for human health.

  19. Concentrating versus non-concentrating reactors for solar photocatalytic degradation of p-nitrotoluene-o-sulfonic acid.

    Science.gov (United States)

    Parra, S; Malato, S; Blanco, J; Péringer, P; Pulgari, C

    2001-01-01

    The photocatalytic oxidation of the non-biodegradable p-nitrotoluene-o-sulfonic acid (p-NTS) in homogeneous (photo-Fenton reactions) and heterogeneous (with TiO2) solutions has been studied at a pilot-scale under solar irradiation at the Plataforma Solar de Almeria (PSA). In this study two different reactors were tested: a medium concentrating radiation system (Heliomans, HM) and a non-concentrating radiation system (CPC). Their advantages and disadvantages for p-NTS degradation have been compared and discussed. The degradation rates obtained in the CPC collector are around three times more efficient than in the HM collectors. However, in both systems, 100% of the initial concentration of p-NTS was removed. Kinetic experiments were performed in both systems using TiO2 suspensions. During the photodegradation, the disappearance of p-NTS was followed by HPLC, the mineralization of the solution by the TOC technique, the evolution of NO3-, NO2-, and SO4(2-) concentration by ionic chromatography, the toxicity by the standard Microtox test, and the biodegradability by BOD5 and COD measurements. The obtained results demonstrated the utility of the heterogeneous catalysis (using TiO2 as catalyst) as a pretreatment method that can be followed by a biological process.

  20. Device for regulating light water nuclear reactors by changing the boric acid concentration in the cooling water circuit

    International Nuclear Information System (INIS)

    Brown, W.W.; Van der Schoot, M.R.

    1980-01-01

    Small changes in boric acid concentration can be carried out quickly by a combination of an ion exchanger with temperature-dependent capacity and an evaporator. No boric acid need be extracted from the circuit or added to it. However, if large changes of concentration are required, boric acid has to be added. The evaporator is then used to separate distilled water and concentrated boric acid when the cooling water is diluted. (DG) [de

  1. EFFECT OF ACID CONCENTRATION ON CHARACTERS OF SILICA GEL SYNTHESIZED FROM SODIUM SILICATE

    Directory of Open Access Journals (Sweden)

    Nuryono Nuryono

    2010-06-01

    Full Text Available In this research, synthesis and characterization of silica gel from sodium silicate through sol-gel process using H2SO4, HCl, and citric acid have been investigated. Synthesis was carried out by mixing and stirring  20 mL of H2SO4, HCl or citric acid  at certain concentration with 50 mL of sodium silicate solution (Na2O 0.17 M and SiO2 0.61 M for one hour and let to form gel.  The gel was washed with distillated water, and dried in an oven at 100 oC. Characterization of silica gel was carried out by determination of acidity, water adsorption capacity, and water content. Identification of functional group and structure were identified using x-ray diffractometer (XRD and infrared (IR spectrophotometer, respectively.  Results showed that at a range of investigated concentration (0.6 - 3.0 M the increase of concentration, formation of gel with H2SO4 tended to be faster, but with HCl and citric acid to be slower. The increase of acid concentration caused water content, water adsorption capacity, and acidity of the silica gel resulted with HCl and citric acid tended to be increased, increased, and increased, but with H2SO4 to be decreased, increased, and decreased, respectively. Based on the IR spectra and XRD data, it could concluded that the synthetic silica gels contained silanol (Si-OH and siloxane (Si-O-Si and were amorphous, showing similar pattern to kieselgel G 60 produced by Merck.   Keywords: silica gel, adsorption capacity, sodium silicate, acidity

  2. Threshold changes in rat brain docosahexaenoic acid incorporation and concentration following graded reductions in dietary alpha-linolenic acid

    Science.gov (United States)

    Taha, Ameer Y.; Chang, Lisa; Chen, Mei

    2016-01-01

    Background This study tested the dietary level of alpha-linolenic acid (α-LNA, 18:3n-3) sufficient to maintain brain 14C-Docosahexaenoic acid (DHA, 22:6n-3) metabolism and concentration following graded α-LNA reduction. Methods 18–21 day male Fischer-344 (CDF) rats were randomized to the AIN-93G diet containing as a % of total fatty acids, 4.6% (“n-3 adequate”), 3.6%, 2.7%, 0.9% or 0.2% (“n-3 deficient”) α-LNA for 15 weeks. Rats were intravenously infused with 14C-DHA to steady state for 5 minutes, serial blood samples collected to obtain plasma and brains excised following microwave fixation. Labeled and unlabeled DHA concentrations were measured in plasma and brain to calculate the incorporation coefficient, k*, and incorporation rate, Jin. Results Compared to 4.6% α-LNA controls, k* was significantly increased in ethanolamine glycerophospholipids in the 0.2% α-LNA group. Circulating unesterified DHA and brain incorporation rates (Jin) were significantly reduced at 0.2% α-LNA. Brain total lipid and phospholipid DHA concentrations were reduced at or below 0.9% α-LNA. Conclusion Threshold changes for brain DHA metabolism and concentration were maintained at or below 0.9% dietary α-LNA, suggesting the presence of homeostatic mechanisms to maintain brain DHA metabolism when dietary α-LNA intake is low. PMID:26869088

  3. Mass transfer during sulfuric acid concentration by evaporation into the air flow

    Directory of Open Access Journals (Sweden)

    V. K. Lukashov

    2016-12-01

    Full Text Available This article shows the results of the study of mass transfer under periodic concentration of sulfuric acid by evaporation inthe gas flow, neutral with respect to the components of acid.Used mathematical model for mass transferbases on the proposed simplified physical representations.This model has allowed to construct an algorithm for calculation the coefficient of mass transfer from the liquid phase into the gas flow. The algorithm uses the experimental data of change the amount of acid and concentration of the water taken from the laboratory tests. Time-based Nusselt diffusion criterion represent the results of the study at different modes of the evaporation process.It has been found that the character of the influence of temperature and initial acid concentration on Nusselt diffusion criterion depends on the variation range of the mass fraction of water in the acid.It is shown that these dependences are well approximated by an exponential function from the dimensionless parameters of the process. This allows usingthem for calculation the mass transfer coefficient into the gas phase in a batch process of concentrating in the range of investigated modes.

  4. Perfluoroalkyl Acid Concentrations in Blood Samples Subjected to Transportation and Processing Delay.

    Science.gov (United States)

    Bach, Cathrine Carlsen; Henriksen, Tine Brink; Bossi, Rossana; Bech, Bodil Hammer; Fuglsang, Jens; Olsen, Jørn; Nohr, Ellen Aagaard

    2015-01-01

    In studies of perfluoroalkyl acids, the validity and comparability of measured concentrations may be affected by differences in the handling of biospecimens. We aimed to investigate whether measured plasma levels of perfluoroalkyl acids differed between blood samples subjected to delay and transportation prior to processing and samples with immediate processing and freezing. Pregnant women recruited at Aarhus University Hospital, Denmark, (n = 88) provided paired blood samples. For each pair of samples, one was immediately processed and plasma was frozen, and the other was delayed and transported as whole blood before processing and freezing of plasma (similar to the Danish National Birth Cohort). We measured 12 perfluoroalkyl acids and present results for compounds with more than 50% of samples above the lower limit of quantification. For samples taken in the winter, relative differences between the paired samples ranged between -77 and +38% for individual perfluoroalkyl acids. In most cases concentrations were lower in the delayed and transported samples, e.g. the relative difference was -29% (95% confidence interval -30; -27) for perfluorooctane sulfonate. For perfluorooctanoate there was no difference between the two setups [corresponding estimate 1% (0, 3)]. Differences were negligible in the summer for all compounds. Transport of blood samples and processing delay, similar to conditions applied in some large, population-based studies, may affect measured perfluoroalkyl acid concentrations, mainly when outdoor temperatures are low. Attention to processing conditions is needed in studies of perfluoroalkyl acid exposure in humans.

  5. Serum free amino acid concentration in hepatic lipidosis of dairy cows in the periparturient period.

    Science.gov (United States)

    Shibano, Ken-ichi; Kawamura, Seiichi

    2006-04-01

    Blood samples were taken from eight multiparous cows at a dairy farm on eight occasions between the prepartum period and peak lactation to study the serum concentrations of amino acids and biochemical constituents. The cows were classified as having either severe hepatic lipidosis (HL) or non-hepatic lipidosis (non-HL) according to their clinical condition after calving and changes in serum biochemical parameters. The serum concentrations of beta-hydroxybutyric acid were higher in the HL group than in the non-HL group (ANOVA: plipidosis.

  6. Study of the interaction metallic cation - ligand in concentrated phosphorus acid media

    International Nuclear Information System (INIS)

    Sefiani, N.; Azzi, M.; Hlaibi, M.; Kossair, A.

    2005-01-01

    The phosphoric acid is more and more used with a high purity. The recovery of recycling element (uranium, vanadium, rare earth...) and the elimination of toxic element (cadmium, molybdenum, lead...) contained in the phosphoric acid are generally realized by extraction or precipitation. It is then very important to understand these impurities behavior in the phosphoric media in order to control their elimination. In this work, the authors considered the presence of some metallic cations (V, Al, fe, U) and fluorides ions as impurity in concentrated phosphoric acid media. (A.L.B.)

  7. Profile of organic acid concentrations in the digestive gland and hemolymph of Biomphalaria glabrata under estivation

    Directory of Open Access Journals (Sweden)

    José Clecildo Barreto Bezerra

    1999-11-01

    Full Text Available Using high performance liquid chromatography (HPLC analysis it was possible to determine simultaneously the concentration of organic acids (pyruvate, lactate, succinate, fumarate, malate, acetate, propionate, acetoacetate, and ß-hydroxybutyrate in the digestive gland and the extracellular concentration of these same acids in the hemolymph of estivating Biomphalaria glabrata, the intermediate host of Schistosoma mansoni. After a 7 day period of estivation, there was a significant increase in the tissue levels of lactate, succinate, malate and acetate compared to non-estivating snails. After 14 days of estivation, the levels of lactate and acetate were also significantly elevated. The hemolymph concentrations of pyruvate and acetate increased significantly after 7 days and acetate concentrations continued to be significantly increased up to 14 days of estivation. The other organic acids studied, such as ketone body acetoacetate and ß-hydroxybutyrate or the volatile acid propionate, did not accumulate. Their tissue concentrations, however, increased on the 7th day of estivation and reached normal levels within two weeks of estivation for some of them. One should take into consideration how the reduction in metabolism can be handled under aerobic conditions, and what role anaerobic pathways may play in both energy formation and redox balance processes.

  8. Copper solvent extraction from chalcopyrite concentrate acid leach solutions by LIX 984

    OpenAIRE

    Elamari K.; Jdid E.A.; Blazy P.

    2006-01-01

    Copper production from ores or sulphide concentrates is classically realized by pyrometallurgical route. In this study, hydrometallurgical treatment of a copper sulphide concentrate, provided by Hajar Mine (ONA-Group, Morocco), was tested by using a mixture of nitric and hexafluorosilicic acids. Copper is present in the solid product as chalcopyrite and its amount is 28.1 % by weight. Leaching stage allows to dissolve more than 90% of copper witch is accompanied, in the same averages, by Zn a...

  9. Serum uric acid concentrations in a Xhosa community in the Transkei of Southern Africa.

    Science.gov (United States)

    Beighton, P; Daynes, G; Soskolne, C L

    1976-01-01

    Serum uric acid (SUA) concentrations were measured in specimens obtained from 479 respondents aged 15 and over during an epidemiological survey of bone and joint conditions in a tribal Xhosa community living in the Transkei, Southern Africa. Population SUA levels in the Xhosa were significantly lower than those previously observed in South Africa Negro groups in rural and urban environments. This finding agrees with the observations that population SUA concentrations tend to rise with increasing complexity of life style. PMID:1275585

  10. Effect of a low-viscosity adhesive resin on the adhesion of metal brackets to enamel etched with hydrochloric or phosphoric acid combined with conventional adhesives.

    Science.gov (United States)

    Yetkiner, Enver; Ozcan, Mutlu; Wegehaupt, Florian Just; Wiegand, Annette; Eden, Ece; Attin, Thomas

    2013-12-01

    This study investigated the effect of a low-viscosity adhesive resin (Icon) applied after either hydrochloric (HCl) or phosphoric acid (H3PO4) on the adhesion of metal brackets to enamel. Failure types were analyzed. The crowns of bovine incisors (N = 20) were sectioned mesio-distally and inciso-gingivally, then randomly assigned to 4 groups according to the following protocols to receive mandibular incisor brackets: 1) H3PO4 (37%)+TransbondXT (3M UNITEK); 2) H3PO4 (37%)+Icon+TransbondXT; 3) HCl (15%)+Icon (DMG)+TransbondXT 4) HCl (15%)+Icon+Heliobond (Ivoclar Vivadent)+TransbondXT. Specimens were stored in distilled water at 37°C for 24 h and thermocycled (5000x, 5°C to 55°C). The shear bond strength (SBS) test was performed using a universal testing machine (1 mm/min). Failure types were classified according to the Adhesive Remnant Index (ARI). Contact angles of adhesive resins were measured (n = 5 per adhesive) on ceramic surfaces. No significant difference in SBS was observed, implying no difference between combinations of adhesive resins and etching agents (p = 0.712; ANOVA). The Weibull distribution presented significantly lower Weibull modulus (m) of group 3 (m = 2.97) compared to other groups (m = 5.2 to 6.6) (p group 1 (45.4 ± 7.9) > group 2 (44.2 ± 10.6) > group 3 (42.6 ± 15.5). While in groups 1, 3, and 4 exclusively an ARI score of 0 (no adhesive left on tooth) was observed, in group 2, only one specimen demonstrated score 1 (less than half of adhesive left on tooth). Contact angle measurements were as follows: Icon (25.86 ± 3.81 degrees), Heliobond (31.98 ± 3.17 degrees), TransbondXT (35 ± 2.21 degrees). Icon can be safely used with the conventional adhesives tested on surfaces etched with either HCl or H3PO4.

  11. Diclofenac removal in urine using strong-base anion exchange polymer resins.

    Science.gov (United States)

    Landry, Kelly A; Boyer, Treavor H

    2013-11-01

    One of the major sources of pharmaceuticals in the environment is wastewater effluent of which human urine contributes the majority of pharmaceuticals. Urine source separation has the potential to isolate pharmaceuticals at a higher concentration for efficient removal as well as produce a nutrient byproduct. This research investigated the efficacy of using strong-base anion exchange polymer resins to remove the widely detected and abundant pharmaceutical, diclofenac, from synthetic human urine under fresh and ureolyzed conditions. The majority of experiments were conducted using a strong-base, macroporous, polystyrene resin (Purolite A520E). Ion-exchange followed a two-step removal rate with rapid removal in 1 h and equilibrium removal in 24 h. Diclofenac removal was >90% at a resin dose of 8 mL/L in both fresh and ureolyzed urine. Sorption of diclofenac onto A520E resin was concurrent with desorption of an equivalent amount of chloride, which indicates the ion-exchange mechanism is occurring. The presence of competing ions such as phosphate and citrate did not significantly impact diclofenac removal. Comparisons of three polystyrene resins (A520E, Dowex 22, Dowex Marathon 11) as well as one polyacrylic resin (IRA958) were conducted to determine the major interactions between anion exchange resin and diclofenac. The results showed that polystyrene resins provide the highest level of diclofenac removal due to electrostatic interactions between quaternary ammonium functional groups of resin and carboxylic acid of diclofenac and non-electrostatic interactions between resin matrix and benzene rings of diclofenac. Diclofenac was effectively desorbed from A520E resin using a regeneration solution that contained 4.5% (m/m) NaCl in an equal-volume mixture of methanol and water. The greater regeneration efficiency of the NaCl/methanol-water mixture over the aqueous NaCl solution supports the importance of non-electrostatic interactions between resin matrix and benzene rings

  12. Effects of Fungicide Treatment on Free Amino Acid Concentration and Acrylamide-Forming Potential in Wheat.

    Science.gov (United States)

    Curtis, Tanya Y; Powers, Stephen J; Halford, Nigel G

    2016-12-28

    Acrylamide forms from free asparagine and reducing sugars during frying, baking, roasting, or high-temperature processing, and cereal products are major contributors to dietary acrylamide intake. Free asparagine concentration is the determining factor for acrylamide-forming potential in cereals, and this study investigated the effect of fungicide application on free asparagine accumulation in wheat grain. Free amino acid concentrations were measured in flour from 47 varieties of wheat grown in a field trial in 2011-2012. The wheat had been supplied with nitrogen and sulfur and treated with growth regulators and fungicides. Acrylamide formation was measured after the flour had been heated at 180 °C for 20 min. Flour was also analyzed from 24 (of the 47) varieties grown in adjacent plots that were treated in identical fashion except that no fungicide was applied, resulting in visible infection by Septoria tritici, yellow rust, and brown rust. Free asparagine concentration in the fungicide-treated wheat ranged from 1.596 to 3.987 mmol kg -1 , with a significant (p fungicide treatment, the increases in acrylamide ranging from 2.7 to 370%. Free aspartic acid concentration also increased, whereas free glutamic acid concentration increased in some varieties but decreased in others, and free proline concentration decreased. The study showed disease control by fungicide application to be an important crop management measure for mitigating the problem of acrylamide formation in wheat products.

  13. Preparation of extractive resins for producing terbium-161; Preparacion de resinas extractivas para produccion de terbio-161

    Energy Technology Data Exchange (ETDEWEB)

    De la Cruz B, C. C.; Monroy G, F. [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)], e-mail: fabiola.monroy@inin.gob.mx

    2009-10-15

    This paper presents the development of a methodology for extractive resins preparation to base of HDEHP, which allows to separation of Tb from Gd generating an own technology of preparation of these resins. The study included the extractive resins preparation from 6 different supports: kieselguhr Dg, alumina, red volcanic rock, chiluca, quarry and fluorite; two treatment types of of supports and varied concentrations of HDEHP extractant (di(2-etil hexyl) orthophosphoric acid), in order to determine which resin has improved efficiency of Gd and Tb separation, and radionuclide purity of {sup 161}Tb. Resins were prepared to base of kieselguhr to determine the most appropriate silicon deposition process. Two silicon deposition treatments were realized: treatment I , by contact with silicon deposition solution (dimethyldichlorosilane / heptane 1:30) and treatment II by contact with vapors of dimethyldichlorosilane in vacuum. The extractant retention was carried out to different concentrations of HDEHP / acetone: 1:4, 1:8, 1:15, 1:20, 1:30 and 1:40. According to the results, there is not direct relation of HDEHP concentration used in extractive resins preparation to base of kieselguhr over the efficiency of Gd and Tb separation and of radionuclide purity of {sup 161}Tb. The effect of support in the efficiency of Gd and Tb separation was studied to prepare resins with the supports kieselguhr, alumina, quarry, chiluca, volcanic rock and fluorite, using the silicon deposition treatment II for the supports and a concentration of HDEHP / acetone 1:20, for extractant retention. Only resins based on kieselguhr could separate to Gd from Tb quantitatively, the resin at a concentration of HDEHP / Acetone 1:20 was the best results obtained in Gd and Tb separation, achieving a separation efficiency greater than 90% and a radionuclide purity higher than 99%. (Author)

  14. Growing and laying performance of Japanese quail fed diet supplemented with different concentrations of acetic acid

    Directory of Open Access Journals (Sweden)

    Youssef A. Attia

    2013-04-01

    Full Text Available In order to evaluate the effect of acetic acid on growing and laying performance of Japanese Quail (JQ, 180 15-day-old JQ were divided into 4 groups. During the growing (15-42 days of age and laying (43-84 days of age periods, the groups fed the same basal diets supplemented with 0, 1.5, 3 and 6% of acetic acid. Each diet was fed to five replicates of 9 JQ (3 males:6 females during the growing period. During the laying period, 128 birds were housed in 32 cages (4 birds per cage, 1 male and 3 females, 8 replicates per treatment. Birds were housed in wire cages (46L×43W×20H cm in an open room. Acetic acid supplementation at 3% in the diets significantly increased the growth and laying rate and the Haugh unit score. The liver percentage significantly decreased with acetic acid at 6%. Acetic acid at 3% significantly increased hemoglobin concentrations at 6 weeks of age and increased weight of day old chicks hatched. Acetic acid affected the immune system as manifested by an excess of cellular reactions in the intestine as well as lymphoid hyperplasia in the spleen tissue. Degenerative changes in the covering epithelium of the intestinal villi were noted at the 6% concentration of acetic acid. Hepatocyte vacuolation and fatty changes were also observed at this concentration of treatment. In conclusion, 3% acetic acid may be used as a feed supplement for JQ during the growing and laying period to improve the productive performance.

  15. Differences in surface roughness of nanohybrid composites immersed in varying concentrations of citric acid

    Directory of Open Access Journals (Sweden)

    Gabriela Kevina Alifen

    2017-06-01

    Full Text Available Background: The surface roughness of restoration is important in predicting the length of time it might remain in the mouth. Conditions within the oral cavity can affect the surface roughness of a restoration. Nanohybrid composite is widely used in dentistry because it can be applied to restore anterior and posterior teeth. Athletes routinely consume isotonic drinks which are acidic and even more erosive than the carbonated variety because they contain a range of acids; the highest content of which being citric acid. Purpose: The aim of the study was to analyze the surface roughness of nanohybrid composite after having been subjected to immersion in varying concentrations of citric acid. Methods: Two isotonic drinks (Pocari Sweat and Mizone were analyzed using high performance liquid chromatography (HPLC to quantify the respective concentrations of citric acid which they contained. A total of 27 samples of cylindrical nanohybrid composite were prepared before being divided into three groups. In Group 1, samples were immersed in citric acid solution derived from Pocari Sweat. Those of Group 2 were immersed in citric acid solution derived from Mizone; while Group 3, samples were immersed in distilled water as a control. All samples were immersed for 7 days, before their surface roughness was tested by means of a surface roughness tester (Mitutoyo SJ-201. Data was analyzed using a one-way ANOVA test. Results: The results showed that there was no significant difference in surface roughness between Groups 1, 2 and 3 (p=0.985. Conclusion: No difference in surface roughness of nanohybrid composites results from prolonged immersion in varying concentrations of citric acid.

  16. Identification of quantitative trait loci controlling linolenic acid concentration in PI483463 (Glycine soja).

    Science.gov (United States)

    Ha, Bo-Keun; Kim, Hyun-Jee; Velusamy, Vijayanand; Vuong, Tri D; Nguyen, Henry T; Shannon, J Grover; Lee, Jeong-Dong

    2014-07-01

    The QTLs controlling alpha-linolenic acid concentration from wild soybean were mapped on nine soybean chromosomes with various phenotypic variations. New QTLs for alpha-linolenic acid were detected in wild soybean. Alpha-linolenic acid (ALA) is a polyunsaturated fatty acid desired in human and animal diets. Some wild soybean (Glycine soja) genotypes are high in ALA. The objective of this study was to identify quantitative trait loci (QTLs) controlling ALA concentration in a wild soybean accession, PI483463. In total, 188 recombinant inbred lines of F5:6, F5:7, and F5:8 generations derived from a cross of wild soybean PI483463 (~15 % ALA) and cultivar Hutcheson (~9 % ALA) were planted in four environments. Harvested seeds were used to measure fatty acid concentration. Single nucleotide polymorphism markers of the universal soybean linkage panel (USLP 1.0) and simple sequence repeat markers were used for molecular genotyping. Nine putative QTLs were identified that controlled ALA concentration by model-based composite interval mapping and mapped to different soybean chromosomes. The QTLs detected in four environments explained 2.4-7.9 % of the total phenotypic variation (PV). Five QTLs, qALA5_3, qALA6_1, qALA14_1, qALA15_1, and qALA17_1, located on chromosomes 5, 6, 14, 15, and 17 were identified by model-based composite interval mapping and composite interval mapping in two individual environments. Among them, qALA6_1 showed the highest contribution to the PV with 10.0-10.2 % in two environments. The total detected QTLs for additive and epistatic effects explained 52.4 % of the PV for ALA concentration. These findings will provide useful information for understanding genetic structure and marker-assisted breeding programs to increase ALA concentration in seeds derived from wild soybean PI483463.

  17. Urea, Uric Acid, Prolactin and fT4 Concentrations in Aqueous Humor of Keratoconus Patients.

    Science.gov (United States)

    Stachon, Tanja; Stachon, Axel; Hartmann, Ulrike; Seitz, Berthold; Langenbucher, Achim; Szentmáry, Nóra

    2017-06-01

    Keratoconus is a noninflammatory disease of the cornea associated with progressive thinning and conical shape. Metabolic alterations in the urea cycle, with changes in collagen fibril stability, oxidative stress, thyroid hormones and prolactin with regulatory effect on biosynthesis and biomechanical stability of corneal stroma, may all play a role in keratoconus etiology. Our purpose was to determine urea, uric acid, prolactin and free thyroxin (fT4) concentrations in human aqueous humor (hAH) of keratoconus and cataract patients. hAH was collected from 100 keratoconus (penetrating keratoplasty) (41.9 ± 14.9 years, 69 males) and 100 cataract patients (cataract surgery) (71.2 ± 12.4 years, 58 males). Urea, uric acid, prolactin and fT4 concentrations were measured by Siemens clinical chemistry or immunoassay system. For statistical analysis, a generalized linear model (GLM) was used. Urea concentration was 11.88 ± 3.03 mg/dl in keratoconus and 16.44 ± 6.40 mg/dl in cataract patients, uric acid 2.04 ± 0.59 mg/dl in keratoconus and 2.18 ± 0.73 mg/dl in cataract groups. Prolactin concentration was 3.18 ± 0.34 ng/ml in keratoconus and 3.33 ± 0.32 ng/ml in cataract patients, fT4 20.57 ± 4.76 pmol/l in KC and 19.06 ± 3.86 pmol/l in cataract group. Urea concentration was effected through gender (p = 0.039), age (p = 0.001) and diagnosis (p = 0.025). Uric acid concentration was not effected through any of the analyzed parameters (p > 0.056). Prolactin and fT4 concentration were effected only through diagnosis (p = 0.009 and p = 0.006). Urea and prolactin concentrations are decreased, fT4 concentration is increased in aqueous humor of keratoconus patients, and uric acid concentration remains unchanged. Urea concentration in aqueous humor is also increased in older and male patients. Therefore, metabolic disorder and hormonal balance may both have an impact on keratoconus development. Further studies are necessary to assess the specific impact.

  18. Salicylic acid induces apoptosis in colon carcinoma cells grown in-vitro: Influence of oxygen and salicylic acid concentration

    International Nuclear Information System (INIS)

    Zitta, Karina; Meybohm, Patrick; Bein, Berthold; Huang, Ying; Heinrich, Christin; Scholz, Jens; Steinfath, Markus; Albrecht, Martin

    2012-01-01

    In solid tumors the hypoxic environment can promote tumor progression and resistance to therapy. Recently, acetylsalicylic acid a major component of analgesic drugs and its metabolite salicylic acid (SA) have been shown to reduce the risk of colon cancer, but the mechanisms of action remain still unclear. Here we elucidate the effects of physiologically relevant concentrations of SA on colon carcinoma cells (CaCo-2) grown under normoxic and hypoxic conditions. Western blotting, caspase-3/7 apoptosis assays, MTS cell-proliferation assays, LDH cytotoxicity assays and hydrogen peroxide measurements were performed to investigate the effects of 1 and 10 μM SA on CaCo-2 cells grown under normoxic conditions and cells exposed to hypoxia. Under normoxic conditions, SA did not influence cell proliferation or LDH release of CaCo-2 cells. However, caspase-3/7 activity was significantly increased. Under hypoxia, cell proliferation was reduced and LDH release and caspase-3/7 activities were increased. None of these parameters was altered by the addition of SA under hypoxic conditions. Hypoxia increased hydrogen peroxide concentrations 300-fold and SA significantly augmented the release of hydrogen peroxide under normoxic, but not under hypoxic conditions. Phosphorylation of the pro-survival kinases akt and erk1/2 was not changed by SA under hypoxic conditions, whereas under normoxia SA reduced phosphorylation of erk1/2 after 2 hours. We conclude that in colon carcinoma cells effects of SA on apoptosis and cellular signaling are dependent on the availability of oxygen. -- Highlights: ► Effects of salicylic acid on colon carcinoma cells grown under normoxic and hypoxic conditions ► Salicylic acid increases caspase-3/7 activity and hydrogen peroxide release under normoxia ► Salicylic acid decreases pro-survival erk-1/2 phosphorylation under normoxia ► Salicylic acid does not influence any of the investigated parameters under hypoxia

  19. Salicylic acid induces apoptosis in colon carcinoma cells grown in-vitro: Influence of oxygen and salicylic acid concentration

    Energy Technology Data Exchange (ETDEWEB)

    Zitta, Karina; Meybohm, Patrick; Bein, Berthold; Huang, Ying; Heinrich, Christin; Scholz, Jens; Steinfath, Markus; Albrecht, Martin, E-mail: Albrecht@anaesthesie.uni-kiel.de

    2012-04-15

    In solid tumors the hypoxic environment can promote tumor progression and resistance to therapy. Recently, acetylsalicylic acid a major component of analgesic drugs and its metabolite salicylic acid (SA) have been shown to reduce the risk of colon cancer, but the mechanisms of action remain still unclear. Here we elucidate the effects of physiologically relevant concentrations of SA on colon carcinoma cells (CaCo-2) grown under normoxic and hypoxic conditions. Western blotting, caspase-3/7 apoptosis assays, MTS cell-proliferation assays, LDH cytotoxicity assays and hydrogen peroxide measurements were performed to investigate the effects of 1 and 10 {mu}M SA on CaCo-2 cells grown under normoxic conditions and cells exposed to hypoxia. Under normoxic conditions, SA did not influence cell proliferation or LDH release of CaCo-2 cells. However, caspase-3/7 activity was significantly increased. Under hypoxia, cell proliferation was reduced and LDH release and caspase-3/7 activities were increased. None of these parameters was altered by the addition of SA under hypoxic conditions. Hypoxia increased hydrogen peroxide concentrations 300-fold and SA significantly augmented the release of hydrogen peroxide under normoxic, but not under hypoxic conditions. Phosphorylation of the pro-survival kinases akt and erk1/2 was not changed by SA under hypoxic conditions, whereas under normoxia SA reduced phosphorylation of erk1/2 after 2 hours. We conclude that in colon carcinoma cells effects of SA on apoptosis and cellular signaling are dependent on the availability of oxygen. -- Highlights: Black-Right-Pointing-Pointer Effects of salicylic acid on colon carcinoma cells grown under normoxic and hypoxic conditions Black-Right-Pointing-Pointer Salicylic acid increases caspase-3/7 activity and hydrogen peroxide release under normoxia Black-Right-Pointing-Pointer Salicylic acid decreases pro-survival erk-1/2 phosphorylation under normoxia Black-Right-Pointing-Pointer Salicylic acid does

  20. Fixation of metallic sulfosalicylate complexes on an anionic exchange resin

    International Nuclear Information System (INIS)

    Cahuzac, S.

    1969-06-01

    Since sulfosalicylate ions have acid-base properties, sulfosalicylate complexes have an apparent stability which varies with the ph. As a result, the fixation of sulfo-salicylates on an anionic exchange resin depends on the ph of the solution in equilibrium with the resin. This research has been aimed at studying the influence of the ph on the fixation on an anionic exchange resin (Dowex 1 x 4) of sulfosalicylate anions on the one hand, and of metallic sulfosalicylate complexes on the other hand. In the first part of this work, a determination has been made, by frontal analysis of the distribution of sulfosalicylate ions in the resin according to the total sulfosalicylate I concentration in the aqueous solution in equilibrium with the resin. The exchange constants of these ions between the resin and the solution have been calculated. In the second part, a study has been made of the fixation of anionic sulfosalicylate complexes of Fe(III), Al(III), Cr(III), Cu(II), Ni(II), Co(II), Zn(II), Mn(II), Cd(II), Fe(II) and UO 2 2+ . By measuring the partition coefficients of these different elements between the resin and the solution it has been possible to give interpretation for the modes of fixation of the metallic ions, and to calculate their exchange constant between the resin and the solution. The relationship has been established for each metallic element studied, between its partition coefficient, the ph and the total concentration of the complexing agent in solution. Such a relationship makes it possible to predict, for given conditions, the nature of the species in solution and in the resin, as well as the partition coefficient of a metallic, element. Finally, in the third part of the work, use has been made of results obtained previously, to carry out some separations (Ni 2+ - Co 2+ ; Ni 2+ - Co 2+ - Cu 2+ ; UO 2 2+ - Fe 3+ ; UO 2 2+ - Cr 3+ ; UO 2 2+ - Cu 2+ ; UO 2 2+ - Ni 2+ ; UO 2 2+ - Co 2+ ; UO 2 2+ - Mn 2+ and UO 2 2+ - Cd 2+ ), as well as the purification

  1. Dry Matter Production and Leaf Elemental Concentrations of Rambutan Grown on an Acid Ultisol

    Science.gov (United States)

    Little is known about the adaptability of rambutan (Nephelium lappaceum) to highly acidic soils rich in aluminum (Al). A 2-yr field study was conducted to determine the effects of various levels of soil Al on dry matter production, plant growth, and nutrient concentration in the leaves of four cult...

  2. Role of lauric acid-potassium hydroxide concentration on bacterial contamination of spray washed broiler carcasses

    Science.gov (United States)

    A series of experiments were conducted to examine reductions in bacterial contamination of broiler carcasses washed in a spray cabinet with various concentrations of lauric acid (LA)-potassium hydroxide (KOH) solutions. Fifty eviscerated carcasses and 5 ceca were obtained from the processing line of...

  3. Body mass index, gestational weight gain and fatty acid concentrations during pregnancy: the Generation R Study

    NARCIS (Netherlands)

    A.J. Vidakovic (Aleksandra Jelena); V.W.V. Jaddoe (Vincent); O. Gishti (Olta); J.F. Felix (Janine); M.A. Williams (Michelle); A. Hofman (Albert); H. Demmelmair (Hans); B. Koletzko (Berthold); H.W. Tiemeier (Henning); R. Gaillard (Romy)

    2015-01-01

    textabstractObesity during pregnancy may be correlated with an adverse nutritional status affecting pregnancy and offspring outcomes. We examined the associations of prepregnancy body mass index and gestational weight gain with plasma fatty acid concentrations in mid-pregnancy. This study was

  4. Ascorbic acid prevents cimetidine-induced decrease of serum hydrocortisone concentrations

    NARCIS (Netherlands)

    M.P. Boidin (Marinus Pieter); A. Stuurman (Arie); W. Erdmann (Wilhelm)

    1990-01-01

    markdownabstractAbstract A blind, parallel, prospective, clinical study was conducted to investigate the effect of ascorbic acid on human serum hydrocortisone concentrations which were decreased by the administration of cimetidine. The study population included 16 male adults scheduled for major

  5. Concentration of phenolic acids and flavonoids in aronia melanocarpa (choke berry) juice by osmotic membrane distillation

    DEFF Research Database (Denmark)

    Fjerbæk Søtoft, Lene; Christensen, Knud Villy; Horn, Vibeke G

    2009-01-01

     Membrane distillation (MD) has been tested as a low temperature replacement of traditional falling film evaporators for juice concentration. Compared to other membrane processes, MD is non-pressure driven performing a high degree of concentration in the same versatile installation[1]. Aronia...... melanocarpa is among the red fruits with the highest content of antioxidants [2] and has gained must interest due to the content of phenolic acids, procyanidins and polyphenolic compounds as anthocyanins [3]. In this study, osmotic membrane distillation (OMD) has been tested for the concentration of not only...

  6. Synthesis of activated carbon-based amino phosphonic acid chelating resin and its adsorption properties for Ce(III) removal.

    Science.gov (United States)

    Chen, Tao; Yan, Chunjie; Wang, Yixia; Tang, Conghai; Zhou, Sen; Zhao, Yuan; Ma, Rui; Duan, Ping

    2015-01-01

    This work aims to investigate the adsorption of Ce(III) onto chelating resin based on activated carbon (CRAC). The CRAC adsorbent was prepared from activated carbon (AC) followed by oxidation, silane coupling, ammoniation and phosphorylation, and characterized by Fourier transform-infrared spectrometry, nitrogen adsorption measurements and scanning electron microscopy. The effects of solution pH, adsorbent dosage and contact time were studied by batch technique. Langmuir and Freundlich isotherms were used to describe the adsorption behaviour of Ce(III) by CRAC, and the results showed that the adsorption behaviour well fitted the Langmuir model. The maximum uptake capacity (qmax) calculated by using the Langmuir equation for cerium ions was found to be 94.34 mg/g. A comparison of the kinetic models and the overall experimental data was best fitted with the type 1 pseudo second-order kinetic model. The calculated thermodynamic parameters (ΔG°, ΔH° and ΔS°) showed that the adsorption for Ce(III) was feasible, spontaneous and exothermic at 25-45 °C. The CRAC showed an excellent adsorptive selectivity towards Ce(III). Moreover, more than 82% of Ce(III) adsorbed onto CRAC could be desorbed with HCl and could be used several times.

  7. Dynamic changes in amino acid concentration profiles in patients with sepsis.

    Directory of Open Access Journals (Sweden)

    Longxiang Su

    Full Text Available The goal of this work was to explore the dynamic concentration profiles of 42 amino acids and the significance of these profiles in relation to sepsis, with the aim of providing guidance for clinical therapies.Thirty-five critically ill patients with sepsis were included. These patients were further divided into sepsis (12 cases and severe sepsis (23 cases groups or survivor (20 cases and non-survivor (15 cases groups. Serum samples from the patients were collected on days 1, 3, 5, 7, 10, and 14 following intensive care unit (ICU admission, and the serum concentrations of 42 amino acids were measured.The metabolic spectrum of the amino acids changed dramatically in patients with sepsis. As the disease progressed further or with poor prognosis, the levels of the different amino acids gradually increased, decreased, or fluctuated over time. The concentrations of sulfur-containing amino acids (SAAs, especially taurine, decreased significantly as the severity of sepsis worsened or with poor prognosis of the patient. The serum concentrations of SAAs, especially taurine, exhibited weak negative correlations with the Sequential Organ Failure Assessment (SOFA (r=-0.319 and Acute Physiology and Chronic Health Evaluation (APACHE II (r=-0.325 scores. The areas under the receiver operating characteristic curves of cystine, taurine, and SAA levels and the SOFA and APACHE II scores, which denoted disease prognosis, were 0.623, 0.674, 0.678, 0.86, and 0.857, respectively.Critically ill patients with disorders of amino acid metabolism, especially of SAAs such as cystine and taurine, may provide an indicator of the need for the nutritional support of sepsis in the clinic.ClinicalTrial.gov identifier NCT01818830.

  8. Cost and Performance Report: Low-Hazardous Air Pollutant (HAP)/Volatile Organic Compound (VOC)-Compliant Resins for Military Applications

    Science.gov (United States)

    2012-03-01

    acid chain length decrease (4), but cost is also a factor. Methacrylated lauric acid monomers represent a balance of these factors...affects the cost. Shorter fatty acids , such as octanoic acid , are more expensive than longer acids , such as lauric acid . Novolac resins are more... acid vinyl ester resin system FAVE-L fatty acid vinyl ester resin system based on lauric acid FAVE-O fatty acid vinyl ester resin system based

  9. Passive Sampler for Measurements of Atmospheric Nitric Acid Vapor (HNO3 Concentrations

    Directory of Open Access Journals (Sweden)

    Andrzej Bytnerowicz

    2001-01-01

    Full Text Available Nitric acid (HNO3 vapor is an important nitrogenous air pollutant responsible for increasing saturation of forests with nitrogen and direct injury to plants. The USDA Forest Service and University of California researchers have developed a simple and inexpensive passive sampler for monitoring air concentrations of HNO3. Nitric acid is selectively absorbed on 47-mm Nylasorb nylon filters with no interference from particulate NO3-. Concentrations determined with the passive samplers closely corresponded with those measured with the co-located honeycomb annular denuder systems. The PVC protective caps of standardized dimensions protect nylon filters from rain and wind and allow for reliable measurements of ambient HNO3 concentrations. The described samplers have been successfully used in Sequoia National Park, the San Bernardino Mountains, and on Mammoth Mountain in California.

  10. Ionic flotation of uranium and of cadmium in concentrated phosphoric acid media

    International Nuclear Information System (INIS)

    Jdid, E.; Bessiere, J.; Blazy, P.

    1984-01-01

    The ionic flotation technique has been applied to concentrated phosphoric acid media (with 30% P 2 O 5 or H 3 PO 4 5.5 M) as a new process for the recovery of uranium and the elimination of cadmium. The results obtained seem to indicate that in these hyperacid media the anionic collectors are better suited than the cationic collectors and that they then permit the flotation of the uranium and cadmium ions with a very rapid kinetics and the achievement of efficiencies of over 90%. In the case of uranium, the collector used remains efficient up to a temperature of 60 0 C with a satisfactory selectivity in the face of others cations present in the commercial phosphoric acid, and which have a penalizing effect on the uraniferous concentrates, and the floated uranium concentrate assays approximately 10% U on a dry basis [fr

  11. Postprandial Plasma Concentrations of Individual Bile Acids and FGF-19 in Patients With Type 2 Diabetes

    DEFF Research Database (Denmark)

    Sonne, David P; van Nierop, F Samuel; Kulik, Willem

    2016-01-01

    controls, but differences were not statistically significant due to considerable variation. CONCLUSION: Postprandial plasma patterns of bile acids with FXR agonistic properties (CDCA, DCA, and CA) and FXR antagonistic properties (UDCA) in T2D patients support the notion of a "T2D-bile acid-FGF-19......CONTEXT: Bile acids regulate lipid and carbohydrate metabolism by interaction with membrane or intracellular proteins including the nuclear farnesoid X receptor (FXR). Postprandial activation of ileal FXR leads to secretion of fibroblast growth factor 19 (FGF-19), a gut hormone that may...... be implicated in postprandial glucose metabolism. OBJECTIVE: To describe postprandial plasma concentrations of 12 individual bile acids and FGF-19 in patients with type 2 diabetes (T2D) and healthy controls. DESIGN AND SETTING: Descriptive study, performed at the Center for Diabetes Research, Gentofte Hospital...

  12. Dietary supplementation with cholesterol and docosahexaenoic acid affects concentrations of amino acids in tissues of young pigs

    Science.gov (United States)

    Li, Peng; Kim, Sung Woo; Li, Xilong; Datta, Sujay; Pond, Wilson G.

    2013-01-01

    Cholesterol and docosahexaenoic acid (DHA) are important nutrients for neural development of infants. However, little is known about the effect of cholesterol or DHA on concentrations of amino acids (AA) in neonatal tissues. This study was conducted with the piglet (an established model for studying human infant nutrition) to test the hypothesis that dietary supplementation with the lipids may modulate AA availability in tissues. Sixteen newborn pigs were nursed by sows for 24 h and then assigned to one of four treatment groups, representing supplementation with 0.0% (control), 0.2% cholesterol, 0.2% DHA, or cholesterol plus DHA to the basal milk-formula. All piglets were euthanized at 49 days of age. In brain, cholesterol supplementation reduced (P < 0.05) concentrations of glutamate, serine, glutamine, threonine, β-alanine, alanine, methionine, isoleucine, leucine, and γ-aminobutyrate but increased (P < 0.05) concentrations of glycine and lysine, whereas DHA supplementation similarly affected (P < 0.05) concentrations of the same AA (except for isoleucine and lysine) and taurine. In addition, concentrations of most AA in liver, muscle and plasma were substantially altered by dietary supplementation of cholesterol and DHA in a tissue-dependent manner. Further, DHA reduced concentrations of carnosine in skeletal muscle, as well as ammonia in both plasma and brain. The results reveal that cholesterol and DHA can regulate AA metabolism and availability in various tissues of piglets. These novel findings have important implications for designing the next generation of infant formula to optimize neonatal growth and development. PMID:18972185

  13. Integrated Microanalytical System for Simultaneous Voltammetric Measurements of Free Metal Ion Concentrations in Natural Waters

    OpenAIRE

    Noël, Stéphane; Tercier-Waeber, Mary-Lou; Lin, Lin; Buffle, Jacques; Guenat, Olivier; Koudelka-Hep, Milena

    2007-01-01

    A complexing gel integrated microelectrode (CGIME) for direct measurements of free metal ion concentrations in natural waters has been developed. It is prepared by the successive deposition of microlayers of a chelating resin, an antifouling agarose gel and Hg on a 100-interconnected Ir-based microelectrode array. The trace metals of interest are in a first step accumulated on the chelating resin in proportion to their free ion concentration in solution, then released in acidic solution and d...

  14. Photosensitive filler minimizes internal stresses in epoxy resins

    Science.gov (United States)

    Dillon, J. N.

    1967-01-01

    Photosensitive filler is added to curable epoxy resins to minimize stress from internal shrinkage during curing or polymerization. Cinnamic acid resins and cinnamal ketones may be added in the amount of 1 to 3 percent by weight of the resin mixture.

  15. Development of radiation-curable resin based on natural rubber

    International Nuclear Information System (INIS)

    Dahlan Mohd; Abdul Ghani Harun

    1993-01-01

    A new radiation curable resin based on natural rubber has been developed. The resin was based on the reaction between low molecular weight epoxidised natural rubber and acrylic acid. When formulated with reactive monomers and photoinitiator, it solidified upon irradiation with UV light. The resin may find applications in coating for cellulosic-based substrates and pressure-sensitive adhesive

  16. Organosulfates and organic acids in Arctic aerosols: speciation, annual variation and concentration levels

    DEFF Research Database (Denmark)

    Hansen, A. M. K.; Kristensen, K.; Nguyen, Q. T.

    2014-01-01

    organosulfates - from both anthropogenic and biogenic precursors were in focus. A total of 11 organic acids (terpenylic acid, benzoic acid, phthalic acid, pinic acid, suberic acid, azelaic acid, adipic acid, pimelic acid, pinonic acid, diaterpenylic acid acetate and 3-methyl-1,2,3-butanetricarboxylic acid), 12...

  17. Novel silica-based ion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    Eichrom`s highly successful Diphonixo resin resembles a conventional ion exchange resin in its use of sulfonic acid ligands on a styrene- divinylbenzene matrix. Diphonix resin exhibits rapid exchange kinetics that allow economical operation of ion exchange systems. Unlike conventional resins, Diphonix resin contains chelating ligands that are diphosphonic acid groups that recognize and remove the targeted metals and reject the more common elements such as sodium, calcium and magnesium. This latter property makes Diphonix ideal for many industrial scale applications, including those involving waste treatment. For treatment of low-level, transuranic (TRU) and high- level radioactive wastes, Diphonix`s polystyrene backbone hinders its application due to radiolytic stability of the carbon-hydrogen bonds and lack of compatibility with expected vitrification schemes. Polystyrene-based Diphonix is approximately 60% carbon- hydrogen. In response to an identified need within the Department of Energy for a resin with the positive attributes of Diphonix that also exhibits greater radiolytic stability and final waste form compatibility, Eichrom has successfully developed a new, silica-based resin version of Diphonix. Target application for this new resin is for use in environmental restoration and waste management situations involving the processing of low-level, transuranic and high-level radioactive wastes. The resin can also be used for processing liquid mixed waste (waste that contains low level radioactivity and hazardous constituents) including mixed wastes contaminated with organic compounds. Silica-based Diphonix is only 10% carbon-hydrogen, with the bulk of the matrix silica.

  18. Efficient fermentation of xylose to ethanol at high formic acid concentrations by metabolically engineered Saccharomyces cerevisiae

    Energy Technology Data Exchange (ETDEWEB)

    Hasunuma, Tomohisa; Yoshimura, Kazuya; Matsuda, Fumio [Kobe Univ., Hyogo (Japan). Organization of Advanced Science and Technology; Sung, Kyung-mo; Sanda, Tomoya; Kondo, Akihiko [Kobe Univ., Hyogo (Japan). Dept. of Chemical Science and Engineering

    2011-05-15

    Recombinant yeast strains highly tolerant to formic acid during xylose fermentation were constructed. Microarray analysis of xylose-fermenting Saccharomyces cerevisiae strain overexpressing endogenous xylulokinase in addition to xylose reductase and xylitol dehydrogenase from Pichia stipitis revealed that upregulation of formate dehydrogenase genes (FDH1 and FDH2) was one of the most prominent transcriptional events against excess formic acid. The quantification of formic acid in medium indicated that the innate activity of FDH was too weak to detoxify formic acid. To reinforce the capability for formic acid breakdown, the FDH1 gene was additionally overexpressed in the xylose-metabolizing recombinant yeast. This modification allowed the yeast to rapidly decompose excess formic acid. The yield and final ethanol concentration in the presence of 20 mM formic acid is as essentially same as that of control. The fermentation profile also indicated that the production of xylitol and glycerol, major by-products in xylose fermentation, was not affected by the upregulation of FDH activity. (orig.)

  19. Postprandial changes in plasma acylcarnitine concentrations as markers of fatty acid flux in overweight and obesity.

    Science.gov (United States)

    Ramos-Roman, Maria A; Sweetman, Lawrence; Valdez, Maressa J; Parks, Elizabeth J

    2012-02-01

    This study determined whether reductions in postprandial plasma nonesterified fatty acid (FFA) flux would lead to reductions in plasma acylcarnitine (AC) concentrations. Plasma AC was measured by liquid chromatography with tandem mass spectrometry in the fasting state and over 6 hours after a high-fat (50% energy) meal was fed to 16 overweight and obese subjects with a wide range of insulin sensitivities. Body composition was measured by dual-energy x-ray absorptiometry; insulin sensitivity by insulin-modified, frequently sampled intravenous glucose tolerance test; substrate oxidation by indirect calorimetry; blood metabolite and hormone concentrations biochemically; and fatty acid flux by using stable isotope tracers. Lean body mass and fasting fat oxidation correlated positively (r > 0.522, P 0.515, P Conditions that impact fatty acid flux contribute to the control of postprandial plasma AC concentrations. These data underscore the need for a better understanding of postprandial fatty acid oxidation and dietary fat delivery in the setting of adipose insulin resistance to determine how postprandial lipemia contributes to chronic disease risk. Copyright © 2012 Elsevier Inc. All rights reserved.

  20. Review: Resin Composite Filling

    OpenAIRE

    Desmond Ng; Jimmy C. M. Hsiao; Keith C. T. Tong; Harry Kim; Yanjie Mai; Keith H. S. Chan

    2010-01-01

    The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin ...

  1. Effect of dimethylamine on the gas phase sulfuric acid concentration measured by Chemical Ionization Mass Spectrometry

    CERN Document Server

    Rondo, L.; Kürten, A.; Adamov, A.; Bianchi, F.; Breitenlechner, M.; Duplissy, J.; Franchin, A.; Dommen, J.; Donahue, N. M.; Dunne, E. M.; Flagan, R. C.; Hakala, J.; Hansel, A.; Keskinen, H.; Kim, J.; Jokinen, T.; Lehtipalo, K.; Leiminger, M.; Praplan, A.; Riccobono, F.; Rissanen, M. P.; Sarnela, N.; Schobesberger, S.; Simon, M.; Sipilä, M.; Smith, J. N.; Tomé, A.; Tröstl, J.; Tsagkogeorgas, G.; Vaattovaara, P.; Winkler, P. M.; Williamson, C.; Wimmer, D.; Baltensperger, U.; Kirkby, J.; Kulmala, M.; Petäjä, T.; Worsnop, D. R.; Curtius, J.

    2016-01-01

    Sulfuric acid is widely recognized as a very important substance driving atmospheric aerosolnucleation. Based on quantum chemical calculations it has been suggested that the quantitative detectionof gas phase sulfuric acid (H2SO4) by use of Chemical Ionization Mass Spectrometry (CIMS) could be biased inthe presence of gas phase amines such as dimethylamine (DMA). An experiment (CLOUD7 campaign) was setup at the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber to investigate the quantitative detection ofH2SO4in the presence of dimethylamine by CIMS at atmospherically relevant concentrations. For the first time inthe CLOUD experiment, the monomer sulfuric acid concentration was measured by a CIMS and by two CI-APi-TOF(Chemical Ionization-Atmospheric Pressure interface-Time Of Flight) mass spectrometers. In addition, neutralsulfuric acid clusters were measured with the CI-APi-TOFs. The CLOUD7 measurements show that in the presenceof dimethylamine (<5 to 70 pptv) the sulfuric acid monomer measured by the CIMS...

  2. Effect of dimethylamine on the gas phase sulfuric acid concentration measured by Chemical Ionization Mass Spectrometry

    Science.gov (United States)

    Rondo, L.; Ehrhart, S.; Kürten, A.; Adamov, A.; Bianchi, F.; Breitenlechner, M.; Duplissy, J.; Franchin, A.; Dommen, J.; Donahue, N. M.; Dunne, E. M.; Flagan, R. C.; Hakala, J.; Hansel, A.; Keskinen, H.; Kim, J.; Jokinen, T.; Lehtipalo, K.; Leiminger, M.; Praplan, A.; Riccobono, F.; Rissanen, M. P.; Sarnela, N.; Schobesberger, S.; Simon, M.; Sipilä, M.; Smith, J. N.; Tomé, A.; Tröstl, J.; Tsagkogeorgas, G.; Vaattovaara, P.; Winkler, P. M.; Williamson, C.; Wimmer, D.; Baltensperger, U.; Kirkby, J.; Kulmala, M.; Petäjä, T.; Worsnop, D. R.; Curtius, J.

    2016-03-01

    Sulfuric acid is widely recognized as a very important substance driving atmospheric aerosol nucleation. Based on quantum chemical calculations it has been suggested that the quantitative detection of gas phase sulfuric acid (H2SO4) by use of Chemical Ionization Mass Spectrometry (CIMS) could be biased in the presence of gas phase amines such as dimethylamine (DMA). An experiment (CLOUD7 campaign) was set up at the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber to investigate the quantitative detection of H2SO4 in the presence of dimethylamine by CIMS at atmospherically relevant concentrations. For the first time in the CLOUD experiment, the monomer sulfuric acid concentration was measured by a CIMS and by two CI-APi-TOF (Chemical Ionization-Atmospheric Pressure interface-Time Of Flight) mass spectrometers. In addition, neutral sulfuric acid clusters were measured with the CI-APi-TOFs. The CLOUD7 measurements show that in the presence of dimethylamine (growth. Although it was found that the addition of dimethylamine dramatically changes the H2SO4 cluster distribution compared to binary (H2SO4-H2O) conditions, the CIMS detection efficiency does not seem to depend substantially on whether an individual H2SO4 monomer is clustered with a DMA molecule. The experimental observations are supported by numerical simulations based on A Self-contained Atmospheric chemistry coDe coupled with a molecular process model (Sulfuric Acid Water NUCleation) operated in the kinetic limit.

  3. Concentration-Discharge Behavior of Contaminants in a Stream Impacted by Acid Mine Drainage

    Science.gov (United States)

    Shaw, M. E.; Klein, M.; Herndon, E.

    2017-12-01

    Acid mine drainage (AMD) has severely degraded streams throughout the Appalachian coal region of the United States. AMD occurs when pyrite contained in coal is exposed to water and air during mining activities and oxidized to release high concentrations of sulfate, metals, and acidity into water bodies. Little is known about the concentration-discharge (CQ) relationships of solutes in AMD-impacted streams due to the complicated nature of acid mine drainage systems. For example, streams may receive inputs from multiple sources that include runoff, constructed treatment systems, and abandoned mines that bypass these systems to continue to contaminate the streams. It is important to understand the CQ relationships of contaminants in AMD-impacted streams in order to elucidate contaminant sources and to predict effects on aquatic ecosystems. Here, we study the CQ behaviors of acid and metals in a contaminated watershed in northeastern Ohio where limestone channels have been installed to remediate water draining from a mine pool into the stream. Stream chemistry was measured in samples collected once per day or once per hour during storm events, and stream flow was measured continuously at the watershed outlet. Increases in stream velocity during storm events resulted in an increase in pH (from 3 to 6) that subsequently decreased back to 3 as flow decreased. Additionally, Fe and Mn concentrations in the stream were high during baseflow (7 and 15 mg/L, respectively) and decreased with increasing discharge during storm events. These results indicate that the treatment system is only effective at neutralizing stream acidity and removing metals when water flow through the limestone channel is continuous. We infer that the acidic and metal-rich baseflow derives from upwelling of contaminated groundwater or subsurface flow from a mine pool. Ongoing studies aim to isolate the source of this baseflow contamination and evaluate the geochemical transformations that occur as it

  4. Serum cholesteryl fatty acid composition and plasma glucose concentrations in Amerindian women.

    Science.gov (United States)

    Lindgärde, Folke; Vessby, Bengt; Ahrén, Bo

    2006-11-01

    Diabetes mellitus has reached epidemic proportions in women of Amerindian origin. The risk of developing diabetes has been found to be related to the serum fatty acid composition in whites. We prospectively investigated the relation between the serum cholesteryl fatty acid composition and changes in fasting plasma glucose concentrations in Peruvian Indian women who are characterized by hyperinsulinemia in comparison to white women. A 5-y follow-up study of 73 women with normal fasting plasma glucose values was undertaken by performing a survey in 1999 and a follow-up survey in 2004. The studied variables included anthropometric measurements, plasma insulin and leptin, dietary food consumption from 24-h recall, blood pressure, and serum fatty acid composition. The participants developed significantly higher fasting plasma glucose concentrations in 2004 compared with 1999 (P percentage of body fat, systolic blood pressure, and circulating triacylglycerol, insulin, leptin, and 16:1n-7 as independent determinants, 16:1n-7 and systolic blood pressure were the only significant determinants of plasma glucose concentration 5 y later. A high proportion of 16:1n-7 in serum is an independent predictor of high plasma glucose concentrations in Amerindian women. The reason for this association remains to be elucidated.

  5. Resin Characterization

    Science.gov (United States)

    2015-06-01

    to see plastic deformation of the surface. 8.1.4.3 Density: Density using the Archimedes principle (ASTM D 792). 8.1.4.4 Density as a Function of...the cure and postcure, quickly cool the sample to 0 °C or lower the temperature to quench the reaction, and then ramp the temperature at 5 °C/min to...prepared by pouring 10 g of resin into a 30-mL screw-cap scintillation vial and adding appropriate amounts of initiator, catalyst, and inhibitor

  6. Epoxidation of linseed oil-Alkyd resins

    International Nuclear Information System (INIS)

    Motawie, A.M.; Ismail, E.A.; Mazroua, A.M.; Abd EI Aziem, M.S.; Ramadan, A.M.

    2004-01-01

    Three types of different linseed oil-alkyd resin ( Alk (I), Alk (II), and Alk (III) ) were prepared with the calculated amounts of mono glycerides and adipic acid (1:1, 1:2, and 2:1 Eq.Wt) respectively via monoglyceride method. The obtained alkyd resins were epoxidized via reaction with the calculated quantities of peracetic acid, which was prepared by the reaction of acetic anhydride with H 2 O 2 . Epoxidation occurred with the ratio (1: 1, 1 :3, and 1:6 Eq. Wt) of alkyd to peracetic acid. The effect of reaction time on the epoxy group content was measured during the epoxidation process. The prepared alkyd resins were analyzed by IR and H 1 NMR. The metal coated film properties of epoxidized alkyd resins were compared with those of unmodified alkyd resins. It was observed that the coating films of epoxidized alkyd resins have better in drying properties, hardness, adhesion, impact and flexibility than those of un epoxidized alkyd resins. The flammability properties of the paper coated films for the prepared brominated epoxidized alkyd resins were found to be fire retardant

  7. Paramagnetic epoxy resin

    Directory of Open Access Journals (Sweden)

    E. C. Vazquez Barreiro

    2017-01-01

    Full Text Available This work illustrates that macrocycles can be used as crosslinking agents for curing epoxy resins, provided that they have appropriate organic functionalities. As macrocycles can complex metal ions in their structure, this curing reaction allows for the introduction of that metal ion into the resin network. As a result, some characteristic physical properties of the metallomacrocycle could be transferred to the new material. The bisphenol A diglycidyl ether (BADGE, n = 0 and hemin (a protoporphyrin IX containing the Fe(III ion, and an additional chloride ligand have been chosen. The new material has been characterized by differential scanning calorimetry (DSC, thermogravimetric analysis (TGA, Fourier Transform Infrared (FT-IR, Nuclear Magnetic Resonance (NMR, Transmission Electron Microscopy (TEM, and magnetic susceptibility measurements. Fe(III remains in the high-spin state during the curing process and, consequently, the final material exhibits the magnetic characteristics of hemin. The loss of the chlorine atom ligand during the cure of the resin allows that Fe(III can act as Lewis acid, catalyzing the crosslinking reactions. At high BADGE n = 0/hemin ratios, the formation of ether and ester bonds occurs simultaneously during the process.

  8. Development of ion-exchange properties of bamboo charcoal modified with concentrated nitric acid

    Science.gov (United States)

    Khandaker, S.; Kuba, T.; Toyohara, Y.; Kamida, S.; Uchikawa, Y.

    2017-08-01

    The surface chemistry and the structural properties of activated carbon can be altered by the acidic modification. The objective of this study is to investigate the changes occurring in bamboo charcoal (BC) during activation with concentrated nitric acid. Low temperature (500°C) carbonized BC has been prepared and oxidized with 70% concentrated boiling nitric acid (BC-AC). The porous properties of the BC are analyzed with nitrogen adsorption isotherm at 77 K. The surface structure is observed by Field emission scanning electronic microscope (FESEM) and the surface functional groups are examined by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and the pH of the point of zero charge (pHPZC). The results reveal that severe oxidation with HNO3 considerably decreases the surface area of BC with enhanced pore widening and FESEM observation demonstrates the erosive effect of oxidation. The FTIR analysis detects that some absorption bands are assigned for carboxyl, aldehyde and ketone groups on BC-AC. The XPS analysis also clearly shows that the ratio of oxygen and acidic functional groups has been enriched significantly on the BC-AC. The low pHPZC value of BC-AC confirms that the surface is highly acidic for the fixation of acidic functional groups on surface. In general, the existence of the abundant amount of acidic functional groups on adsorbents enhances the sorption of heavy metals ions in aqueous solution. Therefore, it is strongly expected that the modified BC, activated under the proposed conditions would be a promising ion exchanger in aqueous solution and can be applied for the adsorption of different heavy metal ions and radioactive materials from effluent.

  9. Demographic, reproductive, and dietary determinants of perfluorooctane sulfonic (PFOS) and perfluorooctanoic acid (PFOA) concentrations in human colostrum

    NARCIS (Netherlands)

    Jusko, T.A.; Oktapodas, M.; Palkovičová Murinová, L.; Babjaková, J.; Verner, M.A.; DeWitt, J.C.; Babinská, K.; Thevenet-Morrison, K.; Čonka, K.; Drobná, B.; Thurston, S.W.; Lawrence, B.P.; Dozier, A.M.; Jarvinen-Seppo, K.M.; Patayová, H.; Trnovec, T.; Legler, J.; Hertz-Picciotto, I.; Lamoree, M.H.

    2016-01-01

    To determine demographic, reproductive, and maternal dietary factors that predict perfluoroalkyl substance (PFAS) concentrations in breast milk, we measured perfluorooctane sulfonic (PFOS) and perfluorooctanoic acid (PFOA) concentrations, using liquid chromatography-mass spectrometry, in 184

  10. Interacting Blends of Novel Unsaturated Polyester Amide Resin with Styrene

    OpenAIRE

    Patel, Hasmukh S.; Panchal, Kumar K.

    2004-01-01

    Novel unsaturated poly (ester-amide) resins (UPEAs) were prepared by the reaction between an epoxy resin, namely diglycidyl ether of bisphenol–A (DGEBA) and unsaturated aliphatic bisamic acids using a base catalyst. These UPEAs were then blended with a vinyl monomer namely, Styrene (STY.) to produce a homogeneous resin syrup. The curing of these UPEAs-STY. resin blends was carried out by using benzoyl peroxide (BPO) as a catalyst and was monitored by using a differential scanning calorimeter ...

  11. [Dental plaque microcosm biofilm behavior on a resin composite incorporated with nano-antibacterial inorganic filler containing long-chain alkyl quaternary ammonium salt].

    Science.gov (United States)

    Junling, Wu; Qiang, Zhang; Ruinan, Sun; Ting, Zhu; Jianhua, Ge; Chuanjian, Zhou

    2015-12-01

    To develop a resin composite incorporated with nano-antibacterial inorganic filler containing long-chain alkyl quaternary ammonium salt, and to measure its effect on human dental plaque microcosm biofilm. A novel nano-antibacterial inorganic filler containing long-chain alkyl quaternary ammonium salt was synthesized according to methods introduced in previous research. Samples of the novel nano-antibacterial inorganic fillers were modified by a coupling agent and then added into resin composite at 0%, 5%, 10%, 15% or 20% mass fractions; 0% composite was used as control. A flexural test was used to measure resin composite mechanical properties. Results showed that a dental plaque microcosm biofilm model with human saliva as inoculum was formed. Colony-forming unit (CFU) counts, lactic acid production, and live/dead assay of biofilm on the resin composite were calculated to test the effect of the resin composite on human dental plaque microcosm biofilm. The incorporation of nano-antibacterial inorganic fillers with as much as 15% concentration into the resin composite showed no adverse effect on the mechanical properties of the resin composite (P > 0.05). Resin composite containing 5% or more nano-antibacterial inorganic fillers significantly inhibited the metabolic activity of dental plaque microcosm biofilm, suggesting its strong antibacterial potency (P < 0.05). This novel resin composite exhibited a strong antibacterial property upon the addition of up to 5% nano-antibacterial inorganic fillers, thereby leading to effective caries inhibition in dental application.

  12. Preparation and characterization of molecularly-imprinted polymers for extraction of sanshool acid amide compounds followed by their separation from pepper oil resin derived from Chinese prickly ash (Zanthoxylum bungeanum).

    Science.gov (United States)

    Chen, Xiaolong; Jin, Xinkai; Li, Yao; Chen, Guangjing; Chen, Kewei; Kan, Jianquan

    2018-01-01

    Molecularly imprinted polymers were prepared using the molecular structure analogs of sanshool as template molecule, 2-vinylpyridine and β-cyclodextrin as double functional monomers, ethylene dimethacrylate as cross linker, and azobisisobutyronitrile as initiator. The structural characteristics of the polymers were determined by Fourier-transform infrared spectroscopy and scanning electron microscopy. Dynamic adsorption and isothermal adsorption were also investigated. The molecularly imprinted polymers were used to prepare a molecularly imprinted solid-phase extraction column in order to separate acid amide components from pepper oil resin derived from Chinese prickly ash (Zanthoxylum bungeanum). After eluting, the percentage of acid amide components was enhanced to 92.40 ± 1.41% compared with 23.34 ± 1.21% in the initial pepper oil resin, indicating good properties of purification of molecularly imprinted polymers and potential industrial application. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Pilot Plant for treating of spent exchange resins

    International Nuclear Information System (INIS)

    Iglesias, Alberto M.; Raffo Calderon, Maria del C.; Varani, Jose L.

    2004-01-01

    Spent exchange resins that have been accumulating during the last operational 30 years in Atucha I nuclear power plant (NPP) are a 'problematic' waste. These spent resins conform an intermediate level waste due to the total content of alpha, beta and gamma emitters (some samples of spent resins were analyzed in 2003). For this reason its treatment is more expensive since it is necessary to add more safety barriers for its final disposition and also for the radioprotection actions that are involved. Using sulfuric acid solutions it is possible to elute from the spent resins the ions that are retained. In the same operation are eluted Cobalt, Cesium and alpha emitters since that all these elements react as cations in aqueous solution. Decontamination by electrochemical methods was analyzed as an interesting method to apply after elution operation to these spent resins since that with the decontamination process it is possible to obtain a solid without activity and concentrate the activity in cells that are small in volume and its manipulation doesn't present any extra complication. Experiments made with active samples taken from the deposit were successful. Because of these results it was built a small plant to treat a batch of 100 dm 3 of wet spent exchange resins. Some problems with the material that was in the deposit together with spent resins caused that we had to plan a more complex strategy to obtain a complete decontamination of the spent resins (in this stage we used the cobalt retention cell that was described in other paper to retain Cobalt and alpha emitters and a sample of zeolites from Argentina ores to retain Cesium). Due to alpha emitters act electrochemically like cations it was possible to retain altogether with ionic Cobalt on the copper amalgam electrode. Working in the non-active lab with alcoholic solutions it was possible to retain ionic Cesium on a copper electrode (copper is covered by mercury fine film which forms a solid amalgam) with a

  14. Influence of different concentrations of jasmonic acid on in vitro development of Catasetum fimbriatum Lindl. (Orchidaceae

    Directory of Open Access Journals (Sweden)

    Juliana Antunes Silva Maia

    2017-10-01

    Full Text Available In vitro seeding constitutes an indispensable tool for propagation of the main commercial species of orchids. This study aimed to analyze the in vitro development of Catasetum fimbriatum under different concentrations of jasmonic acid in Murashige & Skoog culture medium compound of ½ macronutrients. After 180 days of cultivation, concentration of 0.25 and 0.50 μL • L-1 caused a significant increase in number of roots and leaves. The concentration of 1.00 μL • L-1 showed the best result for the length of longest root and largest leaf, the total length of seedling, and the total fresh and dry masses. Nevertheless, the use of this plant regulator on in vitro culture media still requires further investigations to determine the optimal concentration in order to obtain desirable phytotechnical characteristics in different orchid species.

  15. Uranium sorption by tannin resins

    International Nuclear Information System (INIS)

    Olivares Rieumont, S.; Martinez Luzardo, J.; Torres Hernandez, J.; Lima Cazorla, D. de la Rosa.

    1998-01-01

    The sorption of uranium by immobilised Eucalyptus Saligna Sm. and Lysiloma latisiliqua L tannins was investigated. Immobilization condition were analyzed. These resins resulted suitable adsorbent for the concentration of uranium from aqueous systems. The sorption of uranium is pH dependent. At pH 5.5 maximum in sorption capacity is registered. The presence of appreciable amount of sodium chloride do not have any effect on uranium removal. Carbonate and calcium ions in concentrations similar to these that could be found in sea water and other natural water do not decrease the uranium uptake. Tannin resins can be used several times without an appreciable decay of their sorption capacity

  16. Lipoic acid effects on glutamate and taurine concentrations in rat hippocampus after pilocarpine-induced seizures

    Directory of Open Access Journals (Sweden)

    P S Santos

    2011-01-01

    Full Text Available Pilocarpine-induced seizures can be mediated by increases in oxidative stress and by cerebral amino acid changes. The present research suggests that antioxidant compounds may afford some level of neuroprotection against the neurotoxicity of seizures in cellular level. The objective of the present study was to evaluate the lipoic acid (LA effects in glutamate and taurine contents in rat hippocampus after pilocarpine-induced seizures. Wistar rats were treated intraperitoneally (i.p. with 0.9% saline (Control, pilocarpine (400 mg/kg, Pilocarpine, LA (10 mg/kg, LA, and the association of LA (10 mg/kg plus pilocarpine (400 mg/kg, that was injected 30 min before of administration of LA (LA plus pilocarpine. Animals were observed during 24 h. The amino acid concentrations were measured using high-performance liquid chromatograph (HPLC. In pilocarpine group, it was observed a significant increase in glutamate content (37% and a decrease in taurine level (18% in rat hippocampus, when compared to control group. Antioxidant pretreatment significantly reduced the glutamate level (28% and augmented taurine content (32% in rat hippocampus, when compared to pilocarpine group. Our findings strongly support amino acid changes in hippocampus during seizures induced by pilocarpine, and suggest that glutamate-induced brain damage plays a crucial role in pathogenic consequences of seizures, and imply that strong protective effect could be achieved using lipoic acid through the release or decrease in metabolization rate of taurine amino acid during seizures.

  17. Use of Anion Exchange Resins for One-Step Processing of Algae from Harvest to Biofuel

    Directory of Open Access Journals (Sweden)

    Martin Poenie

    2012-07-01

    Full Text Available Some microalgae are particularly attractive as a renewable feedstock for biodiesel production due to their rapid growth, high content of triacylglycerols, and ability to be grown on non-arable land. Unfortunately, obtaining oil from algae is currently cost prohibitive in part due to the need to pump and process large volumes of dilute algal suspensions. In an effort to circumvent this problem, we have explored the use of anion exchange resins for simplifying the processing of algae to biofuel. Anion exchange resins can bind and accumulate the algal cells out of suspension to form a dewatered concentrate. Treatment of the resin-bound algae with sulfuric acid/methanol elutes the algae and regenerates the resin while converting algal lipids to biodiesel. Hydrophobic polymers can remove biodiesel from the sulfuric acid/methanol, allowing the transesterification reagent to be reused. We show that in situ transesterification of algal lipids can efficiently convert algal lipids to fatty acid methyl esters while allowing the resin and transesterification reagent to be recycled numerous times without loss of effectiveness.

  18. General method for calculation of hydrogen-ion concentration in multicomponent acid-base mixtures.

    Science.gov (United States)

    Ventura, D A; Ando, H Y

    1980-08-01

    A generalized method for the rapid evaluation of complicated ionic equilibria in terms of the hydrogen-ion concentration was developed. The method was based on the derivation of a single general equation that could be used to evaluate any mixture. A tableau method also was developed which allowed calculation of the numerical solution to the general equation without computer analysis or graphical or intuitive approximations. Examples illustrating the utility of the method are presented. These examples include a mixture of barbital, citric acid, boric acid, monobasic sodium phosphate, and sodium hydroxide. Calculated hydrogen-ion concentrations showed good agreement with experimental values for simple and complex solutions. The major advantages of the method are its simplicity and the obtainment of numerical solutions without initial approximations in the calculations. However, activity corrections are not included in the calculations.

  19. A Concentrated Hydrochloric Acid-based Method for Complete Recovery of DNA from Bone.

    Science.gov (United States)

    Huynen, Leon; Lambert, David M

    2015-11-01

    The successful extraction of DNA from historical or ancient animal bone is important for the analysis of discriminating genetic markers. Methods used currently rely on the digestion of bone with EDTA and proteinase K, followed by purification with phenol/chloroform and silica bed binding. We have developed a simple concentrated hydrochloric acid-based method that precludes the use of phenol/chloroform purification and can lead to a several-fold increase in DNA yield when compared to other commonly used methods. Concentrated hydrochloric acid was shown to dissolve most of the undigested bone and allowed the efficient recovery of DNA fragments <100 bases in length. This method should prove useful for the recovery of DNAs from highly degraded animal bone, such as that found in historical or ancient samples. © 2015 American Academy of Forensic Sciences.

  20. Effects of salt concentration on the reaction rate of Glc with amino acids, peptides, and proteins.

    Science.gov (United States)

    Yamaguchi, Keiko; Noumi, Yuri; Nakajima, Katsumi; Nagatsuka, Chiharu; Aizawa, Haruko; Nakawaki, Rie; Mizude, Eri; Otsuka, Yuzuru; Homma, Takeshi; Chuyen, Nguyen Van

    2009-11-01

    The reaction between the amino group and the carbonyl group is important in food quality control. Furthermore, advanced glycation end products from foods are considered to relate to aging and diabetes. Thus, it is important to control this reaction. In this study, we investigated the effects of salt concentration on the rates of browning reaction of amino acid, peptides, and proteins. A high concentration of sodium chloride retarded the reaction rate of Glc with amino acids as measured with the absorbance at 470 nm, but did not change the browning rate of Glc with peptides. On the other hand, sodium chloride retarded the browning reaction rate of proteins as measured with polymerization degree or by the loss of Lys. It is hoped that the results of this study will be applied in the control of amino-carbonyl reaction rates in the food industry.

  1. Effect of polysulfone concentration on the performance of membrane-assisted lead acid battery

    Directory of Open Access Journals (Sweden)

    Ahmad Fauzi Ismail

    2002-11-01

    Full Text Available The application of lead acid battery in tropical countries normally faces the problem of water decomposition. This phenomenon is due to the factor of charge-discharge reaction in the battery and heat accumulation caused by hot tropical climate and heat generated from engine compartment. The objective of this study is to analyze the effect of polysulfone concentration on the performance of membrane-assisted lead-acid battery. Gas separation membranes, prepared through wet-dry phase inversion method and using various polysulfone concentrated formulations, were applied on the battery vent holes, for the purpose of preventing electrolyte from evaporating to the atmosphere. The best membrane, which retains the most electrolyte, will be chosen to be applied on the soon-to-be-developed “membrane-assisted maintenance- free battery”. This maintenance-free battery will need no topping up of deionized water every time the electrolyte level goes low.

  2. Low HAP/VOC Compliant Resins for Military Applications

    Science.gov (United States)

    2011-09-01

    on lauric acid FAVE-O fatty acid vinyl ester resin system based on octanoic acid FTIR Fourier transform infrared GIC Mode 1 fracture energy... lauric acid MOct methacrylated octanoic acid MPa megapascals Msi 1 million lb per square inch mW mega watt NESHAP National Emissions Standard... lauric acid (MLau) monomers represent a balance of these factors, as they have good resin and polymer properties, and low cost. Due to the low cost of

  3. Uranium recovery from the concentrated phosphoric acid prepared by the hemi-hydrate process

    International Nuclear Information System (INIS)

    Fouad, E.A.; Mahdy, M.A.; Bakr, M.Y.; Zatout, A.A.

    1995-01-01

    It has been proved that the uranium dissolution from El-sebaiya phosphate ore was possible by using 10 Kg of K Cl O 4 / ton rock during the preparation of high strength phosphoric acid using the hemi hydrate process. In the present work, effective extraction of uranium (about 90%) from the high strength phosphoric acid using a new synergistic solvent mixture of 0.75 M D 2 EHPA/0.1 M TOHPO had been a success. Stripping of uranium from the organic phase was possible by 10 M phosphoric acid while the direct precipitation of uranium concentrate from the later was feasible by using N H 4 F in presence of acetone. 8 figs

  4. Perfluoroalkyl Acid Concentrations in Blood Samples Subjected to Transportation and Processing Delay

    DEFF Research Database (Denmark)

    Bach, Cathrine Carlsen; Henriksen, Tine Brink; Bossi, Rossana

    2015-01-01

    BACKGROUND: In studies of perfluoroalkyl acids, the validity and comparability of measured concentrations may be affected by differences in the handling of biospecimens. We aimed to investigate whether measured plasma levels of perfluoroalkyl acids differed between blood samples subjected to delay...... and transportation prior to processing and samples with immediate processing and freezing. METHODS: Pregnant women recruited at Aarhus University Hospital, Denmark, (n = 88) provided paired blood samples. For each pair of samples, one was immediately processed and plasma was frozen, and the other was delayed...... and transported as whole blood before processing and freezing of plasma (similar to the Danish National Birth Cohort). We measured 12 perfluoroalkyl acids and present results for compounds with more than 50% of samples above the lower limit of quantification. RESULTS: For samples taken in the winter, relative...

  5. Regulation of rat plasma and cerebral cortex oxylipin concentrations with increasing levels of dietary linoleic acid.

    Science.gov (United States)

    Taha, Ameer Y; Hennebelle, Marie; Yang, Jun; Zamora, Daisy; Rapoport, Stanley I; Hammock, Bruce D; Ramsden, Christopher E

    2016-05-11

    Linoleic acid (LA, 18:2n-6) is the most abundant polyunsaturated fatty acid in the North American diet and is a precursor to circulating bioactive fatty acid metabolites implicated in brain disorders. This exploratory study tested the effects of increasing dietary LA on plasma and cerebral cortex metabolites derived from LA, its elongation-desaturation products dihomo-gamma linolenic (DGLA, 20:3n-6) acid and arachidonic acid (AA, 20:4n-6), as well as omega-3 alpha-linolenic (α-LNA, 18:3n-3), eicosapentaenoic (EPA, 20:5n-3) and docosahexaenoic acid (DHA, 22:6n-3). Plasma and cortex were obtained from rats fed a 0.4%, 5.2% or 10.5% energy LA diet for 15 weeks and subjected to liquid chromatography tandem mass spectrometry analysis. Total oxylipin concentrations, representing the esterified and unesterified pool, and unesterified oxylipins derived from LA and AA were significantly increased and EPA metabolites decreased in plasma at 5.2% or 10.5% energy LA compared to 0.4% energy LA. Unesterified plasma DHA metabolites also decreased at 10.5% energy LA. In cortex, total and unesterified LA and AA metabolites increased and unesterified EPA metabolites decreased at 5.2% or 10.5% LA. DGLA and α-LNA metabolites did not significantly change in plasma or cortex. Dietary LA lowering represents a feasible approach for targeting plasma and brain LA, AA, EPA or DHA-derived metabolite concentrations. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Effect of dimethylamine on the gas phase sulfuric acid concentration measured by Chemical Ionization Mass Spectrometry.

    Science.gov (United States)

    Rondo, L; Ehrhart, S; Kürten, A; Adamov, A; Bianchi, F; Breitenlechner, M; Duplissy, J; Franchin, A; Dommen, J; Donahue, N M; Dunne, E M; Flagan, R C; Hakala, J; Hansel, A; Keskinen, H; Kim, J; Jokinen, T; Lehtipalo, K; Leiminger, M; Praplan, A; Riccobono, F; Rissanen, M P; Sarnela, N; Schobesberger, S; Simon, M; Sipilä, M; Smith, J N; Tomé, A; Tröstl, J; Tsagkogeorgas, G; Vaattovaara, P; Winkler, P M; Williamson, C; Wimmer, D; Baltensperger, U; Kirkby, J; Kulmala, M; Petäjä, T; Worsnop, D R; Curtius, J

    2016-03-27

    Sulfuric acid is widely recognized as a very important substance driving atmospheric aerosol nucleation. Based on quantum chemical calculations it has been suggested that the quantitative detection of gas phase sulfuric acid (H 2 SO 4 ) by use of Chemical Ionization Mass Spectrometry (CIMS) could be biased in the presence of gas phase amines such as dimethylamine (DMA). An experiment (CLOUD7 campaign) was set up at the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber to investigate the quantitative detection of H 2 SO 4 in the presence of dimethylamine by CIMS at atmospherically relevant concentrations. For the first time in the CLOUD experiment, the monomer sulfuric acid concentration was measured by a CIMS and by two CI-APi-TOF (Chemical Ionization-Atmospheric Pressure interface-Time Of Flight) mass spectrometers. In addition, neutral sulfuric acid clusters were measured with the CI-APi-TOFs. The CLOUD7 measurements show that in the presence of dimethylamine (sulfuric acid monomer measured by the CIMS represents only a fraction of the total H 2 SO 4 , contained in the monomer and the clusters that is available for particle growth. Although it was found that the addition of dimethylamine dramatically changes the H 2 SO 4 cluster distribution compared to binary (H 2 SO 4 -H 2 O) conditions, the CIMS detection efficiency does not seem to depend substantially on whether an individual H 2 SO 4 monomer is clustered with a DMA molecule. The experimental observations are supported by numerical simulations based on A Self-contained Atmospheric chemistry coDe coupled with a molecular process model (Sulfuric Acid Water NUCleation) operated in the kinetic limit.

  7. Trends in Pinus ponderosa foliar pigment concentration due to chronic exposure of ozone and acid rain

    International Nuclear Information System (INIS)

    Neuman, L.; Houpis, J.; Anderson, P.

    1991-01-01

    To determine the effects of ozone and acid rain on mature Ponderosa pine trees, Lawrence Livermore National Lab. has collaborated with University of California Berkeley, University of California Davis, California State University Chico, and the US Forest Service at the latter's Chico Tree Improvement Center. Foliar tissue from mature grafted scions of Pinus ponderosa were exposed to two times ambient ozone for ten months and to acid rain (3.0 pH) weekly for 10 weeks using branch exposure chambers. Pigment extracts were analyzed spectrophotometrically for concentrations of chlorophylls a and b, and carotenoid pigments, at 662 nm, 644 nm, and 470 nm, respectively. Pigment concentrations were expressed on a surface area basis. Preliminary results revealed that chlorophyll a showed a downward trend due to the ozone treatment. Acid rain caused no effects on these three pigments, however, chlorophyll b showed an upward trend due to the interaction of ozone and acid rain. The carotenoid pigments showed no changes due to the treatments either singly, or in combination

  8. Influence of nitric acid concentration on the characteristics of active carbons obtained from a mineral coal

    Energy Technology Data Exchange (ETDEWEB)

    Khelifi, A.; Temdrara, L.; Addoun, A. [Laboratoire d' Etude Physicochimique des Materiaux et Application a l' Environnement, Faculte de Chimie, USTHB, BP. 32 El Alia, Bab Ezzouar 16111, Algiers (Algeria); Almazan-Almazan, M.C.; Perez-Mendoza, M.; Domingo-Garcia, M.; Lopez-Garzon, F.J [Departamento de Quimica Inorganica, Facultad de Ciencias, 18071 Granada (Spain); Lopez-Domingo, F.J. [Departamento de CCIA, ETS de Ingenieria Informatica y Telecomunicacion, Granada, 18071 (Spain)

    2010-10-15

    This paper deals with the effect of the concentration of nitric acid solutions on the properties of activated carbons obtained by the oxidation of a parent activated carbon. For this purpose a mineral coal from Algeria has been used as raw material to prepare the parent active carbon AC. This was further treated with nitric acid solutions. The analysis of the samples includes the chemical and textural characterization. The former was carried out by selective titrations and FTIR spectroscopy. The latter, by nitrogen and carbon dioxide adsorption at 77 and 273 K, respectively, and by adsorption of organic probes (benzene, dichloromethane, cyclohexane and 2,2-dimethyl butane) at 303 K. The nitrogen adsorption isotherms have been analysed by using the BET equation, {alpha}{sub s}-method and molecular simulation. The Dubinin-Radushkevich approach has been applied to the carbon dioxide and vapours adsorption data. The results show that the treatment with 2 N nitric acid solution is very appropriate because it introduces a large amount of oxygen containing groups with a small change of the textural characteristics of the parent AC. More concentrated nitric acid solutions change in large extent the textural properties although they also introduce large amount of chemical groups. (author)

  9. Effect of Drying Temperature on Rosmarinic Acid and Sinensetin Concentration in Orthosiphon stamineus Herbal Leaves

    Science.gov (United States)

    Abdullah, Sriyana; Razak Shaari, Abdul; Hajar Rukunudin, Ibni; Syarhabil Ahmad, Muhammad

    2018-03-01

    The objective of this work was to investigate the effects of drying temperature on the concentration of O rthosiphon stamineus biomarker compounds which were rosmarinic acid (RA) and sinensetin (SEN). The thin layer drying approach was used to dry O. stamineus leaves at various temperatures of 30, 40 and 50°C using a laboratory scale hot air dryer. The dried leaves were then extracted using 60% aqueous methanol prior to quantification. The RA and SEN concentrations in the dried leaves extracts were quantified by the high performance liquid chromatography. The concentration of RA for the dried leaves at 30 and 40°C were higher as compared to that of the fresh leaves. This may due to the response of the plant cells to abiotic stress. The concentration of RA also showed a significant reduction when the temperature was increased to 50°C. In contrast, the SEN concentration in O. stamineus dried leaf extract was lower than that of the fresh samples. The concentrations of SEN depicted insignificant effects by drying at 30 and 50°C, and the highest value was obtained in the samples dried at 40°C. Results showed that the drying process was found to affect the concentration of both compounds; therefore suitable drying conditions should be adopted to enhance the medicinal values of the plant species.

  10. Effect of Ascorbic Acid on Shear Bond Strength of Orthodontic Brackets Bonded with Resin-modified Glass-ionomer Cement to Bleached Teeth

    Directory of Open Access Journals (Sweden)

    Behnam Khosravanifard

    2012-04-01

    Full Text Available Background and aims. Bleaching can considerably reduce shear bond strength (SBS of orthodontic brackets bonded with composite adhesives. Application of antioxidants is a method to reverse the negative effect of bleaching on compositeto-enamel bond. However, the efficacy of antioxidants in increasing the SBS of brackets bonded using resin-modified glassionomer cement (RMGIC has not been studied, which was the aim of this study. Materials and methods. Fifty freshly extracted human maxillary first premolars were bleached with 35% hydrogen peroxide (Pola Office Bleaching, SDI. Sodium ascorbate 10% was applied to the experimental specimens (n=25. All the specimens were etched with 37% phosphoric acid (Ivoclar/Vivadent and bonded using RMGIC (Fuji Ortho LC, GC. The specimens were subjected to incubation (37°C, 24h and thermocycling (1000 cycles, 5-55°C, dwell time = 1 min. The SBS was measured at 0.5 mm/min debonding crosshead speed. The adhesive remnant index (ARI was scored under ×10 magnification. Data were analyzed using Mann-Whitney U test, one- and independent-samples t-test, and Fisher’s exact test (α=0.05. Results. The mean SBS of experimental and control groups were 11.97 ± 4.49 and 7.7 ± 3.19 MPa, respectively. The difference was statistically significant (P=0.000 by t-test. SBS of both control (P=0.014 and experimental (P=0.000 groups were significantly higher than the minimum acceptable SBS of 6 MPa, according to one-sample t-test. Conclusion. Application of ascorbic acid can guarantee a strong bond when RMGIC is to be used. However, RMGIC might tolerate the negative effect of bleaching with minimum SA treatments (or perhaps without treatments, which deserves further studies.

  11. D-tagatose, a stereoisomer of D-fructose, increases blood uric acid concentration.

    Science.gov (United States)

    Buemann, B; Toubro, S; Holst, J J; Rehfeld, J F; Bibby, B M; Astrup, A

    2000-08-01

    D-Fructose has been found to increase uric acid production by accelerating the degradation of purine nucleotides, probably due to hepatocellular depletion of inorganic phosphate (Pi) by an accumulation of ketohexose-1-phosphate. The hyperuricemic effect of D-tagatose, a stereoisomer of D-fructose, may be greater than that of D-fructose, as the subsequent degradation of D-tagatose-1-phosphate is slower than the degradation of D-fructose-1-phosphate. We tested the effect of 30 g oral D-tagatose versus D-fructose on plasma uric acid and other metabolic parameters in 8 male subjects by a double-blind crossover design. Both the peak concentration and 4-hour area under the curve (AUC) of serum uric acid were significantly higher after D-tagatose compared with either 30 g D-fructose or plain water. The decline in serum Pi concentration was greater at 50 minutes after D-tagatose versus D-fructose. The thermogenic and lactacidemic responses to D-tagatose were blunted compared with D-fructose. D-Tagatose attenuated the glycemic and insulinemic responses to a meal that was consumed 255 minutes after its administration. Moreover, both fructose and D-tagatose increased plasma concentrations of cholecystokinin (CCK) and glucagon-like peptide-1 (GLP-1). The metabolic effects of D-tagatose occurred despite its putative poor absorption.

  12. [Post-cholecystectomy condition: duodeno-gastric reflux and bile acid concentration in the gastric juice].

    Science.gov (United States)

    Koelsch, K A; Kühne, C; Zemlin, C

    1979-07-01

    In cholecystectomized patients highly significantly more frequently a duodenogastric reflux was found than in a group of patients with a healthy abdomen and a group of patients with cholelithiasis. The average concentration of bile acid in the gastric juice was after the removal of the gall-bladder manifoldly higher than in the control groups. The number of patients with concentrated reflux was also highly significantly larger than in patients with cholelithiasis not operated on and in patients with a healthy abdomen. Despite the high reflux rate and the high concentration of the bile acids influencing on the mucous membrane of the stomach the number of patients with ulcera ventriculi was not significantly larger than in a group of not cholecystectomized persons. These observations plead for the fact that the bile acids in the duodenogastric reflux alone are not to be regarded as an ulcerogenic agent, but that perhaps other components of the duodenal juice have to be considered as causes of lesions of the gastric mucous membrane.

  13. Predicted effects of mineral neutralization and bisulfate formation on hydrogen ion concentration for dilute sulfuric acid pretreatment.

    Science.gov (United States)

    Lloyd, Todd A; Wyman, Charles E

    2004-01-01

    Dilute acid and water-only hemicellulose hydrolysis are being examined as part of a multiinstitutional cooperative effort to evaluate the performance of leading cellulosic biomass pretreatment technologies on a common basis. Cellulosic biomass, such as agricultural residues and forest wastes, can have a significant mineral content. It has been shown that these minerals neutralize some of the acid during dilute acid pretreatment, reducing its effectiveness, and the higher solids loadings desired to minimize costs will require increased acid use to compensate. However, for sulfuric acid in particular, an equilibrium shift to formation of bisulfate during neutralization can further reduce hydrogen ion concentrations and compound the effect of neutralization. Because the equilibrium shift has a more pronounced effect at lower acid concentrations, additional acid is needed to compensate. Coupled with the effect of temperature on acid dissociation, these effects increase acid requirements to achieve a particular reaction rate unless minerals are removed prior to hydrolysis.

  14. Processing large-diameter poly(L-lactic acid) microfiber mesh/mesenchymal stromal cell constructs via resin embedding: an efficient histologic method

    International Nuclear Information System (INIS)

    D’Alessandro, Delfo; Danti, Serena; Pertici, Gianni; Moscato, Stefania; Metelli, Maria Rita; Petrini, Mario; Danti, Sabrina; Berrettini, Stefano; Nesti, Claudia

    2014-01-01

    In this study, we performed a complete histologic analysis of constructs based on large diameter ( > 100 μm) poly-L-lactic acid (PLLA) microfibers obtained via dry-wet spinning and rat Mesenchymal Stromal Cells (rMSCs) differentiated towards the osteogenic lineage, using acrylic resin embedding. In many synthetic polymer-based microfiber meshes, ex post processability of fiber/cell constructs for histologic analysis may face deterring difficulties, leading to an incomplete investigation of the potential of these scaffolds. Indeed, while polymeric nanofiber (fiber diameter = tens of nanometers)/cell constructs can usually be embedded in common histologic media and easily sectioned, preserving the material structure and the antigenic reactivity, histologic analysis of large polymeric microfiber/cell constructs in the literature is really scant. This affects microfiber scaffolds based on FDA-approved and widely used polymers such as PLLA and its copolymers. Indeed, for such constructs, especially those with fiber diameter and fiber interspace much larger than cell size, standard histologic processing is usually inefficient due to inhomogeneous hardness and lack of cohesion between the synthetic and the biological phases under sectioning. In this study, the microfiber/MSC constructs were embedded in acrylic resin and the staining/reaction procedures were calibrated to demonstrate the possibility of successfully employing histologic methods in tissue engineering studies even in such difficult cases. We histologically investigated the main osteogenic markers and extracellular matrix molecules, such as alkaline phosphatase, osteopontin, osteocalcin, TGF-β1, Runx2, Collagen type I and the presence of amorphous, fibrillar and mineralized matrix. Biochemical tests were employed to confirm our findings. This protocol permitted efficient sectioning of the treated constructs and good penetration of the histologic reagents, thus allowing distribution and expression of

  15. Recovery of boric acid from ion exchangers

    International Nuclear Information System (INIS)

    Pollock, C.W.

    1976-01-01

    The recovery of boric acid from an anion exchange resin is improved by eluting the boric acid with an aqueous solution of ammonium bicarbonate. The boric acid can be readily purified and concentrated by distilling off the water and ammonium bicarbonate. This process is especially useful for the recovery of boric acid containing a high percentage of 10 B which may be found in some nuclear reactor coolant solutions. 10 claims

  16. Inflammatory markers in dependence on the plasma concentration of 37 fatty acids after the coronary stent implantation.

    Science.gov (United States)

    Handl, Jiří; Meloun, Milan; Mužáková, Vladimíra

    2018-02-05

    Using the regression model building the relationships between the concentration of 37 fatty acids of blood plasma phospholipids of 41 patients with coronary artery disease after coronary stent implantation, the inflammatory response and oxidative stress markers were estimated. The dynamics of the inflammatory response and the oxidative stress was indicated by measuring plasma concentrations of highly sensitive C-reactive protein, interleukin-6, serum amyloid A and malondialdehyde before, 24h after stent implantation. The multiple linear regression analysis was preceded by an exploratory data analysis, principal component analysis, factor analysis and cluster analysis, which proved a hidden internal relation of 37 fatty acids. The concentration of cerotic acid (C26:0) has been positively associated with an increase of malondialdehyde concentration after stent implantation, while the concentrations of tetracosatetraenoic (C24:4 N6) and nonadecanoic (C19:0) acids were associated with decrease of lipoperoxidation. The increase of interleukin-6 during the 24h after implantation was associated with higher levels of pentadecanoic acid (C15:0) and lower levels of α-linolenic acid (C18:3 N3). Regression models found several significant fatty acids at which the strength of the parameter β for each fatty acid on selected markers of C-reactive protein, malondialdehyde, interleukin-6 and serum amyloid A was estimated. Parameter β testifies to the power of the positive or negative relationship of the fatty acid concentration on the concentration of selected markers. The influencing effect of the cerotic acid (C26:0) concentration in plasma phospholipids exhibiting parameter β=140.4 is, for example, 3.5 times higher than this effect of n-3 tetracosapentaenoic acid (C24:5 N3) with β=40.0. Composition of fatty acids in plasma phospholipids shows spectrum of fatty acids available for intercellular communication in systemic inflammatory response of organism and should affect

  17. Mineral Element Concentrations in Vegetables Cultivated in Acidic Compared to Alkaline Areas of South Sweden

    Directory of Open Access Journals (Sweden)

    Ingegerd Rosborg

    2009-01-01

    Full Text Available A study in 1997, on mineral levels in acidic compared to alkaline well waters, and in women’s hair, revealed higher concentrations of a number of mineral elements like Ca, Mo and Se in alkaline waters and hair. Thus, median Ca levels were six times higher in well water and five times higher in hair from the alkaline area compared to the acidic area. This finding raised the probability of similar differences in vegetables from these areas. Thus, in the year 2006, 60 women who had participated in the study in 1997 were asked to cultivate parsley, lettuce, carrot and chive. During the spring of 2006, the women from the water and hair study of 1997, 30 of them from the acidic area and 30 women from the alkaline district cultivated vegetables: carrot (Daucus carota L, parsley (Petroselinum crispum, chive (Allium schoenoprasum and lettuce (Eruca sativa. The vegetables were harvested, and rinsed in tap water from the kitchens of the participating women in August. The concentrations of about 35 elements and ions were determined by ICP OES and ICP-MS predominantly. In addition, soil samples from the different cultivators were also analyzed for a number of elements. Lettuce and parsley showed the highest concentrations of mineral elements per gram dry weight. Only Mo concentrations were significantly higher in all the different vegetables from the alkaline district compared to vegetables from the acidic areas. On the other hand, the concentrations of Ba, Br, Mn, Rb and Zn were higher in all the different vegetables from the acidic area. In the soil, only pH and exchangeable Ca from the alkaline area were higher than from the acidic area, while exchangeable Fe, Mn and Na concentrations were higher in soils from the acidic area. Soil elements like Al, Fe, Li, Ni, Pb, Si, Ti, V, Zn and Zr were found in higher concentrations in lettuce and parsley, which were attributed to soil particles being splashed on the plants by the rain and absorbed by the leaves

  18. The development of 126Sn separation procedure by means of TBP resin

    International Nuclear Information System (INIS)

    Andris, Boris; Bena, Jozef

    2016-01-01

    Separation possibilities of 126 Sn with a new extraction-chromatographic material TBP Resin were studied. Suitable conditions for tin separation were determined in hydrochloric acid medium. 126 Sn was concentrated on TBP resin from 6 mol L -1 HCl and was eluted with 0.1 mol L -1 HCl. A purification step to remove 137 Cs with AMP-PAN column was necessary to obtain sufficiently purified samples which were directly measured with gamma spectrometry for 126 Sn activity. Separation of 126 Sn from a raw sludge sample was done according to proposed procedure, 126 Sn was detected and its activity was determined. (author)

  19. [Optimization of preparative separation and purification of water-soluble substance from Salvia miltiorrhiza by macroporous resins].

    Science.gov (United States)

    He, Wei; Li, Yong; Shen, Xue-mei; Sun, Li-min

    2007-10-01

    To study the optimum conditions for the isolation and purification of water-soluble substance from Salvia miltiorrhiza Bge. The optimum macroporous resin was selected and the separation and purification process was evaluated by measuring the content of Salvianolic acid B in the fractions by HPLC. The XDA-5 macroporous resin was the most effective compared with other macroporous resins. The optimum conditions were screened, which were 18 mg/ml corresponding to Salvianolic acid B for concentration of extract, pH was 4, and the volume of 70% (V/V) ethanol as eluant was 3 BV. By this method, the elution efficiency of Salvianolic acid B exceeded 90%. The method is more effective for large-scale isolation and purification of water-soluble substance from Salvia miltiorrhiza Bge.

  20. Reduced gamma-aminobutyric acid concentration is associated with physical disability in progressive multiple sclerosis

    Science.gov (United States)

    Solanky, Bhavana S.; Muhlert, Nils; Tur, Carmen; Edden, Richard A. E.; Wheeler-Kingshott, Claudia A. M.; Miller, David H.; Thompson, Alan J.; Ciccarelli, Olga

    2015-01-01

    Neurodegeneration is thought to be the major cause of ongoing, irreversible disability in progressive stages of multiple sclerosis. Gamma-aminobutyric acid is the principle inhibitory neurotransmitter in the brain. The aims of this study were to investigate if gamma-aminobutyric acid levels (i) are abnormal in patients with secondary progressive multiple sclerosis compared with healthy controls; and (ii) correlate with physical and cognitive performance in this patient population. Thirty patients with secondary progressive multiple sclerosis and 17 healthy control subjects underwent single-voxel MEGA-PRESS (MEscher-GArwood Point RESolved Spectroscopy) magnetic resonance spectroscopy at 3 T, to quantify gamma-aminobutyric acid levels in the prefrontal cortex, right hippocampus and left sensorimotor cortex. All subjects were assessed clinically and underwent a cognitive assessment. Multiple linear regression models were used to compare differences in gamma-aminobutyric acid concentrations between patients and controls adjusting for age, gender and tissue fractions within each spectroscopic voxel. Regression was used to examine the relationships between the cognitive function and physical disability scores specific for these regions with gamma-aminobuytric acid levels, adjusting for age, gender, and total N-acetyl-aspartate and glutamine-glutamate complex levels. When compared with controls, patients performed significantly worse on all motor and sensory tests, and were cognitively impaired in processing speed and verbal memory. Patients had significantly lower gamma-aminobutyric acid levels in the hippocampus (adjusted difference = −0.403 mM, 95% confidence intervals −0.792, −0.014, P = 0.043) and sensorimotor cortex (adjusted difference = −0.385 mM, 95% confidence intervals −0.667, −0.104, P = 0.009) compared with controls. In patients, reduced motor function in the right upper and lower limb was associated with lower gamma-aminobutyric acid

  1. The association between concentration of Uric Acid and metabolic syndrome among adolescents

    Directory of Open Access Journals (Sweden)

    Homeira Rashidi

    2015-11-01

    Full Text Available Background: Metabolic syndromes are known as a set of risk factors for the development of cardio-vascular disease and diabetes in the individual. The association between concentration of uric acid and metabolic syndrome in adolescents has yet to be established thoroughly. The aim of this study was to investigate the relationship between uric acid and metabolic syndrome in a sample of adolescents. Methods: This cross-sectional study was conducted from September 23, 2009 to September 22, 2010 in Jundishapur University of Medical Sciences, Ahvaz, Iran. In this study, 240 individuals aged 10-19 years were randomly selected among participants of the Ahvaz MetS study (120 subjects normal and 120 subjects MetS. The serum levels of UA were measured by a colorimetric method. In the normal group, anyone with abdominal obesity, high systolic or diastolic blood pressure, High-density lipoprotein (HDL≤40 mg/dl, TG≤110 mg/dl, fasting blood sugar (FBS≤100 mg/dl or diabetes was excluded from the study. History of Anticonvulsive drugs or steroids use was the criteria for exclusion for both groups. Results: Of the 240 subjects aged a mean of 14.95±2.64 years, mean of uric acid in metabolic syndrome group was 4.8±1.4 mg/dl and in the control group was 4.18±1.01 mg/d (P=0.001. Participants were divided into three groups based on uric acid levels: ≤4.9 mg/dl, 4.9-5.7 mg/dl and >5.7 mg/dl. The risk of metabolic syndrome was significantly higher in third group of uric acid than the second and first group (odds ratio [OR], 3.7; 95% confidence interval [CI], 1.70 - 8.04 and (OR, 5.9; 95% CI, 2.42-14.35, P<0.001. In addition, uric acid level was inversely associated with hyperglycemia. The ORs of hypertriglyceridemia for the second and third group of uric acid were 4.36 (95% CI, 2.01- 9.47 5.75 (95% CI, 2.43-13.61 respectively, compared with lowest group of UA. Conclusion: The results showed that hyperuricemia was significantly linked with increased risk for

  2. Fatty Acid and Cholesterol Concentrations in Usually Consumed Fish in Brazil

    Directory of Open Access Journals (Sweden)

    Carlos Scherr

    2015-02-01

    Full Text Available Background: Several studies have demonstrated clinical benefits of fish consumption for the cardiovascular system. These effects are attributed to the increased amounts of polyunsaturated fatty acids in these foods. However, the concentrations of fatty acids may vary according to region. Objective: The goal of this study was to determine the amount of,cholesterol and fatty acids in 10 Brazilian fishes and in a non-native farmed salmon usually consumed in Brazil. Methods: The concentrations of cholesterol and fatty acids, especially omega-3, were determined in grilled fishes. Each fish sample was divided in 3 sub-samples (chops and each one was extracted from the fish to minimize possible differences in muscle and fat contents. Results: The largest cholesterol amount was found in white grouper (107.6 mg/100 g of fish and the smallest in badejo (70 mg/100 g. Omega-3 amount varied from 0.01 g/100 g in badejo to 0.900 g/100 g in weakfish. Saturated fat varied from 0.687 g/100 g in seabass to 4.530 g/100 g in filhote. The salmon had the greatest concentration of polyunsaturated fats (3.29 g/100 g and the highest content of monounsaturated was found in pescadinha (5.98 g/100 g. Whiting and boyfriend had the best omega-6/omega 3 ratios respectively 2.22 and 1.19, however these species showed very little amounts of omega-3. Conclusion: All studied Brazilian fishes and imported salmon have low amounts of saturated fat and most of them also have low amounts of omega-3.

  3. Low plasma eicosapentaenoic acid concentration as a possible risk factor for intracerebral hemorrhage.

    Science.gov (United States)

    Ikeya, Yoshimori; Fukuyama, Naoto; Mori, Hidezo

    2015-03-01

    N-3 fatty acids, including eicosapentaenoic acid (EPA), prevent ischemic stroke. The preventive effect has been attributed to an antithrombic effect induced by elevated EPA and reduced arachidonic acid (AA) levels. However, the relationship between intracranial hemorrhage and N-3 fatty acids has not yet been elucidated. In this cross-sectional study, we compared common clinical and lifestyle parameters between 70 patients with intracranial hemorrhages and 66 control subjects. The parameters included blood chemistry data, smoking, alcohol intake, fish consumption, and the incidences of underlying diseases. The comparisons were performed using the Mann-Whitney U test followed by multiple logistic regression analysis. Nonparametric tests revealed that the 70 patients with intracerebral hemorrhages exhibited significantly higher diastolic blood pressures and alcohol intakes and lower body mass indices, high-density lipoprotein (HDL) cholesterol levels, EPA concentrations, EPA/AA ratios, and vegetable consumption compared with the 66 control subjects. A multiple logistic regression analysis revealed that higher diastolic blood pressure and alcohol intake and lower body mass index, HDL cholesterol, EPA/AA ratio, and vegetable consumption were relative risk factors for intracerebral hemorrhage. High HDL cholesterol was a common risk factor in both of the sex-segregated subgroups and the Eicosapentaenoic acid was relative risk factor only in the ≥65-year-old subgroup. Rather than higher EPA levels, lower EPA concentrations and EPA/AA ratios were found to be risk factors for intracerebral hemorrhage in addition to previously known risk factors such as blood pressure, alcohol consumption, and lifestyle. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Preconcentration of Cu (II) from seawater using a novel and stable phenol-formaldehyde resin.

    Science.gov (United States)

    Manivannan, D; Starvin, Maria; Biju, V M

    2010-01-01

    Preconcentration of Cu (II) from seawater using a novel phenol-formaldehyde (P-F) resin was investigated. 1,2-dihydroxybenzene-4-azo-3-hydroxybenzene-formaldehyde resin (DAHBF) was prepared by condensing 1,2-dihydroxybenzene-4-azo-3-hydroxybenzene with formaldehyde (1:2 mole ratio) in the presence of oxalic acid as catalyst. Polychelates were obtained when the DAHBF was treated with the aqueous solution of Cu (II) ions. The polymeric resin and polymer-metal complexes were characterized with thermal analysis and spectral studies. The IR spectra of polychelates suggest that the metal was coordinated through the oxygen atoms of the dihydroxybenzene moiety. The TGA data revealed the thermal stability of the resin and the polychelates. X-ray diffraction study revealed the incorporation of the metal ion significantly enhanced the degree of crystallinity. The sorption properties of the chelate forming resin towards divalent metal ion [Cu(II)] was studied as a function of pH, preconcentration time, metal concentration, amount of resin, aqueous phase volume and presence of electrolyte. This procedure was validated for recovery of copper from seawater samples. The method has adequate accuracy and it can be used for determination of copper in sea water samples.

  5. Effects of total gastrectomy on plasma silicon and amino acid concentrations in men.

    Science.gov (United States)

    Tatara, Marcin R; Krupski, Witold; Szpetnar, Maria; Dąbrowski, Andrzej; Bury, Paweł; Szabelska, Anna; Charuta, Anna; Boguszewska-Czubara, Anna; Maciejewski, Ryszard; Wallner, Grzegorz

    2015-12-01

    The aim of the study was to determine one-year effects of total gastrectomy on plasma silicon and free amino acid concentrations in patients and evaluate changes of volumetric bone mineral density (vBMD) in lumbar spine. Eight patients were enrolled to the control (CTR) group. Six patients subjected to total gastrectomy (GX group) were included to the experimental group. vBMD in trabecular and cortical bone was measured in lumbar vertebrae at baseline (before surgery) and one year later using quantitative computed tomography. Plasma concentrations of silicon and free amino acids were determined at baseline and one year later using photometric method and ion-exchange chromatography. Body weights within CTR and GX groups were not different after one-year follow-up when compared to the baseline values (P > 0.05). An average annual decrease of vBMD in the trabecular bone in the gastrectomized patients reached 15.0% in lumbar spine and was significantly different in comparison to the percentage changes observed in CTR group (P = 0.02). One-year percentage change of vBMD in the cortical bone in L1 and L2 has shown significantly decreased values by 10.5 and 9.1% in the GX group when compared to the percentage change observed in the controls (P silicon was significantly lowered by 26.7% one year after the total gastrectomy when compared to the baseline value (P = 0.009). Total gastrectomy in patients has induced severe osteoporotic changes in lumbar spine within one-year period. The observed osteoporotic changes were associated with decreased plasma concentration of silicon indicating importance of exocrine and endocrine functions of stomach for silicon homeostasis maintenance. Gastrectomy-induced bone loss was not related to decreased amino acid concentration in plasma obtained from overnight fasted patients. © 2015 by the Society for Experimental Biology and Medicine.

  6. Associations of fatty acids in cerebrospinal fluid with peripheral glucose concentrations and energy metabolism.

    Directory of Open Access Journals (Sweden)

    Reiner Jumpertz

    Full Text Available Rodent experiments have emphasized a role of central fatty acid (FA species, such as oleic acid, in regulating peripheral glucose and energy metabolism. Thus, we hypothesized that central FAs are related to peripheral glucose regulation and energy expenditure in humans. To test this we measured FA species profiles in cerebrospinal fluid (CSF and plasma of 32 individuals who stayed in our clinical inpatient unit for 6 days. Body composition was measured by dual energy X-ray absorptiometry and glucose regulation by an oral glucose test (OGTT followed by measurements of 24 hour (24EE and sleep energy expenditure (SLEEP as well as respiratory quotient (RQ in a respiratory chamber. CSF was obtained via lumbar punctures; FA concentrations were measured by liquid chromatography/mass spectrometry. As expected, FA concentrations were higher in plasma compared to CSF. Individuals with high concentrations of CSF very-long-chain saturated FAs had lower rates of SLEEP. In the plasma moderate associations of these FAs with higher 24EE were observed. Moreover, CSF monounsaturated long-chain FA (palmitoleic and oleic acid concentrations were associated with lower RQs and lower glucose area under the curve during the OGTT. Thus, FAs in the CSF strongly correlated with peripheral metabolic traits. These physiological parameters were most specific to long-chain monounsaturated (C16:1, C18:1 and very-long-chain saturated (C24:0, C26:0 FAs.Together with previous animal experiments these initial cross-sectional human data indicate that central FA species are linked to peripheral glucose and energy homeostasis.

  7. Functionalization of chitosan with 3,4-dihydroxybenzoic acid for the adsorption/collection of uranium in water samples and its determination by inductively coupled plasma-mass spectrometry

    OpenAIRE

    Sabarudin, Akhmad; Oshima, Mitsuko; Takayanagi, Toshio; Hakim, Lukman; Oshita, Koji; Gao, Yun Hua; Motomizu, Shoji

    2007-01-01

    A chitosan resin derivatized with 3,4-dihydroxybenzoic acid moiety (CCTS-DHBA resin) was newly synthesized for the collection/concentration of trace uranium by using cross-linked chitosan (CCTS) as base material, and the adsorption behavior of uranium as well as 60 elements on the resin was examined by passing the sample solutions through a mini-column packed with the resin. After the elution of the collected elements on the resin with 1M HNO3, the eluates were measured by inductively coupled...

  8. Cloning and expression of a CYP720B orthologue involved in the biosynthesis of diterpene resin acids in Pinus brutia.

    Science.gov (United States)

    Semiz, Asli; Sen, Alaattin

    2015-03-01

    Cytochrome P450 monooxygenases mediate a broad range of oxidative reactions involved in the biosynthesis of both primary and secondary metabolites in plants. Until now, only two P450 genes, CYP720B1 from Pinus taeda and CYP720B4 from Picea sitchensis, have been functionally characterised and described in the literature. The purpose of this study was to describe the cloning and expression of CYP720B from Pinus brutia due to its suggested role in the synthesis of bioactive compounds used for chemical defence against insects. A PCR product of the P. brutia CYP720B gene was cloned into the pCR8/GW/TOPO cloning vector. After optimising the sequence for codon usage in yeast, it was transferred into the inducible expression vector pYES-DEST52 and transfected into the S. cerevisiae INVSc1 strain. Sequence analysis showed that the P. brutia CYP720B gene contains an open reading frame of 1,464 nucleotides, which encodes a 53,570 Da putative protein of 487 amino acid residues. The putative protein contains the classic heme-binding sequence motif that is conserved in all P450 enzymes. It shares 99 and 61% identity with the deduced amino acid sequences of CYP720B1 from Pinus taeda and CYP720B4 from Picea sitchensis, respectively. Recombinant CYP720B protein expression was confirmed using western blot analysis. Furthermore, recombinant CYP720B was functionally active, showing a Soret peak at approximately 448 nm in the reduced CO difference spectra. These data suggest that the cloned gene is an orthologue of CYP720B in P. brutia and might be involved in DRA biosynthesis.

  9. Variation in the concentration of carminic acid produced by Dactylopius coccus (Hemiptera: Dactylopidae) at various maturation stages.

    Science.gov (United States)

    Flores-Alatorre, H L; Abrego-Reyes, V; Reyes-Esparza, J A; Angeles, E; Alba-Hurtado, F

    2014-08-01

    The concentration of carminic acid was found to vary based on the size and life cycle stage of the cochineal, Dactylopius coccus Costa. The concentration of carminic acid in cochineal eggs, nymph I, nymph II, fertilized adults, ovipositing adults, and sterile adults female was measured using capillary electrophoresis, and the total fluorescence of the carminic acid globules was measured using flow cytometry. The smallest sterile adult females had a greater percentage of carminic acid relative to their weight (26.27%; P acid than the remainder of the females. Nymph II was the phase that had the smallest percentage of carminic acid. Using flow cytometry, it was demonstrated that ovipositing females had a greater total fluorescence than the other sampled groups (P acid and the total fluorescence of the carminic acid globules (r2 = 0.68; P shall allow an improvement of the current classification criteria of the commercial quality of dry cochineal.

  10. Effect of acid concentration and pulp properties on hydrolysis reactions of mercerized sisal.

    Science.gov (United States)

    Lacerda, Talita M; Zambon, Márcia D; Frollini, Elisabete

    2013-03-01

    The influence of sulfuric acid concentration (H2SO4 5-25%, 100°C), crystallinity and fibers size on the hydrolysis reaction of sisal pulps were investigated, with the goal of evaluating both the liquor composition, as an important step in the production of bioethanol, and the residual non-hydrolyzed pulp, to determine its potential application as materials. Aliquots were withdrawn from the reaction media, and the liquor composition was analyzed by HPLC. The residual non-hydrolyzed pulps were characterized by SEM, their average molar mass and crystallinity index, and their size distribution was determined using a fiber analyzer. Sulfuric acid 25% led to the highest glucose content (approximately 10gL(-1)), and this acid concentration was chosen to evaluate the influence of both the fiber size and crystallinity of the starting pulp on hydrolysis. The results showed that fibers with higher length and lower crystallinity favored glucose production in approximately 12%, with respect to the highly crystalline shorter fibers. Copyright © 2012 Elsevier Ltd. All rights reserved.

  11. Thermodynamic and kinetic modelling of the reduction of concentrated nitric acid

    International Nuclear Information System (INIS)

    Sicsic, David

    2011-01-01

    This research thesis aimed at determining and quantifying the different stages of the reduction mechanism in the case of concentrated nitric acid. After having reported the results of a bibliographical study on the chemical and electrochemical behaviour of concentrated nitric media (generalities, chemical equilibriums, NOx reactivity, electrochemical reduction of nitric acid), the author reports the development and discusses the results of a thermodynamic simulation of a nitric environment at 25 C. This allowed the main species to be identified in the liquid and gaseous phases of nitric acid solutions. The author reports an experimental electrochemical investigation coupled with analytic techniques (infrared and UV-visible spectroscopy) and shows that the reduction process depends on the cathodic overvoltage, and identifies three potential areas. A kinetic modelling of the stationary state and of the impedance is then developed in order to better determine, discuss and quantify the reduction process. The application of this kinetic model to the preliminary results of an electrochemical study performed on 304 L steel is then discussed [fr

  12. Separation and concentration of lanthanoids using microcapsules containing acidic organophosphorus compounds as an extractant

    Energy Technology Data Exchange (ETDEWEB)

    Kamio, Eiji; Kondo, Kazuo [Doshisha Univ., Department of Chemical Engineering and Materials Science, Kyoto (Japan)

    2002-06-01

    In this study, we measured the extraction equilibria of lanthanoids with microcapsules containing acidic organophosphorus compound as an extractant and discuss their mutual separation by using a column packed with the microcapsules. The extraction equilibria of lanthanoids into the microcapsules containing 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (EHPNA) were elucidated and the extraction equilibrium constants were calculated by slope-analysis method. It was suggested that the lanthanoid ions are extracted in the microcapsules in a high loading state. Furthermore, the adsorption behavior of lanthanoids into the column packed with the microcapsules containing EHPNA was observed. It was found that adsorption and elution of lanthanoids are briefly achieved by selecting pH of the feed aqueous solution. However, it was impossible to separate them only in adsorption or elution operation. So, the mutual separation of lanthanoids was investigated using the adsorption column connected to the development column containing microcapsules. By selecting pH of the eluent, each metal was separated mutually in more than 95% of purity. The metal ions in the eluent from the development column could be concentrated by treating it with a column packed with the microcapsules containing di(2-ethylhexyl) phosphoric acid (D2EHPA). Considering these information, it will be possible to design a continuous extracting, separating and concentrating reactor of lanthanoids using a column packed with the microcapsules. (author)

  13. Regulation of dipeptide transport in Saccharomyces cerevisiae by micromolar amino acid concentrations

    International Nuclear Information System (INIS)

    Island, M.D.; Naider, F.; Becker, J.M.

    1987-01-01

    Prototrophic Saccharomyces cerevisiae X2180, when grown on unsupplemented minimal medium, displayed little sensitivity to ethionine- and m-fluorophenylalanine-containing toxic dipeptides. The authors examined the influence of the 20 naturally occurring amino acids on sensitivity to toxic dipeptides. A number of these amino acids, at concentrations as low as 1 μM (leucine and tryptophan), produced large increases in sensitivity to leucyl-ethionine, alanyl-ethionine, and leucyl-m-fluorophenylalanine. Sensitivity to ethionine and m-fluorophenylalanine remained high under either set of conditions. The addition of 0.15 mM tryptophan to a growing culture resulted in the induction of dipeptide transport, as indicated by a 25-fold increase in the initial rate of L-leucyl-L[ 3 H]leucine accumulation. This increase, which was prevented by the addition of cycloheximide, began within 30 min and peaked approximately 240 min after a shift to medium containing tryptophan. Comparable increases in peptidase activity were not apparent in crude cell extracts form tryptophan-induced cultures. The authors concluded that S. cerevisiae possesses a specific mechanism for the induction of dipeptidetransport that can respond to very low concentrations of amino acids

  14. Variation of ascorbic acid concentration in fruits of cultivated and wild apples.

    Science.gov (United States)

    Fang, Ting; Zhen, Qiaoling; Liao, Liao; Owiti, Albert; Zhao, Li; Korban, Schuyler S; Han, Yuepeng

    2017-06-15

    Ascorbic acid (AsA) content in mature fruits of 457 apple accessions were measured, and a great variation in AsA concentration was detected. Wild fruits showed significantly higher level of AsA than cultivated fruits. Fruit AsA content was positively correlated with malic acid content, but negatively correlated with fruit weight and soluble solid content. Thus, the difference in AsA content between the wild and cultivated fruits could be attributed to an indirect consequence of human selection for larger fruit size, less acidity, and increased sweetness during apple domestication. Additionally, AsA concentration was extremely high in fruit at the juvenile stage, but dramatically decreased at the expanding and mature stages. The expression levels of three genes controlling AsA accumulation, MdGGP1, MdDHAR3-3, and MdNAT7-2, were significantly negatively correlated with AsA contents in fruits, suggesting a feedback regulation mechanism in AsA-related gene expression. Our results could be helpful for future apple breeding. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Comparison of the irritation potentials of Boswellia serrata gum resin and of acetyl-11-keto-beta-boswellic acid by in vitro cytotoxicity tests on human skin-derived cell lines.

    Science.gov (United States)

    Burlando, Bruno; Parodi, Alessandro; Volante, Andrea; Bassi, Anna Maria

    2008-03-15

    Indian frankincense is a gum resin from Boswellia serrata of Burseraceae used in Ayurveda and Western medicine for the antinflammatory effects of boswellic acids, particularly 3-O-acetyl-11-keto-beta-boswellic acid (AKBA). We evaluated in vitro cytotoxicities of B. serrata extract and AKBA on differentiated and undifferentiated keratinocytes (HaCaT and NCTC 2544), and foetal dermal fibroblasts (HFFF2), using neutral red uptake (NRU), MTT, and DNA assays. Comparison between NRU and MTT, and between the extract and AKBA, suggested a relatively higher toxicity of both substances on lysosomes respect to mitochondria. Extract cytotoxicity on lysosomes was higher in NCTC and HFFF2 than on the more differentiated HaCaT. DNA assay showed low extract inhibition on HFFF2 proliferation, possibly due to lower growth rate, and a stronger effect on NCTC than on HaCaT, possibly related to higher proapoptotic effect on the less differentiated NCTC, as also suggested by higher AKBA toxicity on NCTC than on HaCaT. In general, gum resin and AKBA toxicities were slightly lower or higher than that of the reference compound SDS. Our in vitro model allowed to compare the sensitivities of different human skin cells to B. serrata, and indicated that the gum resin and AKBA exert moderate to low toxicity on the skin.

  16. Microbiological study of water-softener resins.

    Science.gov (United States)

    Stamm, J M; Engelhard, W E; Parsons, J E

    1969-09-01

    Microbial identification using effluents backflushed from exhausted urban and rural tank resins and cleaned resins containing the sulfonated copolymer of styrene and divinylbenzene (SDB) were completed, along with microbial assessment of the concentrated stock salt brine. Forty-four different bacterial and fungal genera were identified. Extensive biochemical and animal virulence tests completed on one of the six bacterial salt brine isolates indicated a pathogenic staphylococcal strain. The retention of Staphylococcus aureus, a Flavobacterium sp, and Escherichia coli B bacteriophage was demonstrated both by using the nonexhausted sodium-regenerated resin and by using the same resin exchanged with different mono-, di-, and trivalent cations. Effluent counts completed after bacterial seepage through the resins indicated the Pb(++) exchanged resin removed 55% of the bacteria; Na(+), Fe(++), and Al(+++) removed 31 to 36% and Ca(++) and Cu(++) removed about 10 to 15%. Seventy per cent or more of the bacteriophage was removed by Fe(++), Cu(++), and Al(+++), whereas the Ca(++) and Na(++) cations removed 25 to 31%. Over a 77-day period, nonsterile tap water was passed through bacterial seeded and uninoculated SDB (Na) resin columns. Effluent and resin elution counts demonstrated the growth and survival of 2 different bacteria per column. Increased bacterial retention, survival, and multiplication occurred concomitantly with accumulation of organic and inorganic materials and the Ca(++) and Mg(++) cations from the tap water. Furthermore, microbial elution from resin particles taken from column depths of 1, 8, and 16 cm indicated a bacterial diminution with increasing depths.

  17. Supplementation of calves with stabilized orthosilicic acid. Effect on the Si, Ca, Mg, and P concentrations in serum and the collagen concentration in skin and cartilage.

    Science.gov (United States)

    Calomme, M R; Vanden Berghe, D A

    1997-02-01

    The bioavailability of silicon in stabilized orthosilicic acid was investigated in a double blind, placebo controlled supplementation study of calves maintained on a normal diet. The total dietary Si intake was increased by 4.9% in the form of stabilized orthosilicic acid. After 23 wk of Si supplementation, the serum Si concentration increased (p = 0.0001, n = 29) by 70% compared to control animals in spite of the low Si dose administered and the Si adequate diet. The individually administered Si dose was significantly associated with the serum Si concentration (r = 0.44, p = 0.016, n = 29). The collagen concentration in dermis was significantly higher (p = 0.019, n = 4) in the Si group and a positive correlation (r = 0.72, p = 0.018, n = 9) was found between the Si concentration in serum and the collagen concentration in cartilage. The calcium (Ca) and phosphorus (P) concentrations in serum were marginally higher for animals supplemented with Si compared to control animals. In serum, a significant linear relationship was found between the Si and the Ca concentration (r = 0.31, p = 0.019, n = 59), whereas the magnesium concentration correlated marginally with the Si concentration (r = 0.25, p = 0.068, n = 59). In summary, increasing the total dietary Si intake by 4.9% in the form of stabilized orthosilicic acid resulted in a 70% higher Si concentration in serum indicating a high bioavailability of Si in this supplement. The positive correlation between the serum Si concentration and the collagen concentration in cartilage and the serum Ca concentration, respectively, suggest the involvement of Si both in the formation of extracellular matrix components and in Ca metabolism.

  18. Control of resin production in Araucaria angustifolia, an ancient South American conifer.

    Science.gov (United States)

    Perotti, J C; da Silva Rodrigues-Corrêa, K C; Fett-Neto, A G

    2015-07-01

    Araucaria angustifolia is an ancient slow-growing conifer that characterises parts of the Southern Atlantic Forest biome, currently listed as a critically endangered species. The species also produces bark resin, although the factors controlling its resinosis are largely unknown. To better understand this defence-related process, we examined the resin exudation response of A. angustifolia upon treatment with well-known chemical stimulators used in fast-growing conifers producing both bark and wood resin, such as Pinus elliottii. The initial hypothesis was that A. angustifolia would display significant differences in the regulation of resinosis. The effect of Ethrel(®) (ET - ethylene precursor), salicylic acid (SA), jasmonic acid (JA), sulphuric acid (SuA) and sodium nitroprusside (SNP - nitric oxide donor) on resin yield and composition in young plants of A. angustifolia was examined. In at least one of the concentrations tested, and frequently in more than one, an aqueous glycerol solution applied on fresh wound sites of the stem with one or more of the adjuvants examined promoted an increase in resin yield, as well as monoterpene concentration (α-pinene, β-pinene, camphene and limonene). Higher yields and longer exudation periods were observed with JA and ET, another feature shared with Pinus resinosis. The results suggest that resinosis control is similar in Araucaria and Pinus. In addition, A. angustifolia resin may be a relevant source of valuable terpene chemicals, whose production may be increased by using stimulating pastes containing the identified adjuvants. © 2014 German Botanical Society and The Royal Botanical Society of the Netherlands.

  19. Analysis of Factors Influencing Soil Salinity, Acidity, and Arsenic Concentration in a Polder in Southwest Bangladesh

    Science.gov (United States)

    Ayers, J. C.; Patton, B.; Fry, D. C.; Goodbred, S. L., Jr.

    2017-12-01

    Soil samples were collected on Polder 32 in the coastal zone of SW Bangladesh in wet (October) and dry (May) seasons from 2013-2017 and analyzed to characterize the problems of soil salinization and arsenic contamination and identify their causes. Soils are entisols formed from recently deposited, predominantly silt-sized sediments with low carbon concentrations typical of the local mangrove forests. Soluble (DI extract) arsenic concentrations were below the Government of Bangladesh limit of 50 ppb for drinking water. Soil acidity and extract arsenic concentrations exhibit spatial variation but no consistent trends. In October soil extract As is higher and S and pH are lower than in May. These observations suggest that wet season rainwater oxidizes pyrite, reducing soil S and releasing H+, causing pH to decrease. Released iron is oxidized to form Hydrous Ferric Oxyhydroxides (HFOs), which sorb As and increase extractable As in wet season soils. Changes in pH are small due to pH buffering by soil carbonates. Soil and rice paddy water salinities are consistently higher in May than October, reaching levels in May that reduce rice yields. Rice grown in paddies should be unaffected by salt concentrations in the wet season, while arsenic concentrations in soil may be high enough to cause unsafe As levels in produced rice.

  20. Impact of acetic acid concentration of fermented liquid feed on growth performance of piglets

    DEFF Research Database (Denmark)

    Canibe, Nuria; Pedersen, Anni Øyan; Jensen, Bent Borg

    2010-01-01

    Feeding fermented liquid feed (FLF) to pigs has proven to benefit gastrointestinal health of the animals. However, growth performance data of piglets and growing pigs fed FLF are variable and often a lower feed intake compared to feeding non-FLF or dry feed has been observed. Accumulation...... of microbial metabolites, namely acetic acid, possibly in combination with low feed pH, has been suggested to be determinant in reducing feed intake by impairing palatability. However, this hypothesis has never been investigated. A study was carried out to determine the impact of increasing levels of acetic...... intake and body weight were registered weekly. The results showed that high acetic acid concentration in FLF, accompanied by a slight lower pH level, tended to decrease feed intake without affecting body weight gain. This discrepancy could partly be explained by the difficulty in measuring accurately...

  1. Purification of baddeleyite concentrate by melting with sulfuric acid and its salts

    International Nuclear Information System (INIS)

    Lebedev, V.N.

    2009-01-01

    Black baddeleyite concentrate of the composition %: 87.4 ZrO 2 , 1.5 SiO 2 , 2.5 TiO 2 , 0.51 Fe 2 O 3 , 1.6 CaO, 3.4 Nb 2 O 5 , 0.59 Ta 2 O 5 has been used for the experiments. Sulfatization was conducted by 93% sulfuric acid with the ammonium, sodium and potassium salts additions. Sulfate mass was leaching at 60 Deg C by water during 1 h. Specific radioactivity of precipitates has been analyzed by radiometric and gamma spectrometric methods. Additions of ammonium, potassium and sodium sulfates increase the degree of decontamination, reduce the consumption of sulfuric acid to 20 %, and the temperature of sulfatization. Degree of decontamination increases with increasing additives in the system Na 2 SO 4 >(NH 4 )SO 4 >K 2 SO 4

  2. Effects of plant proteins on postprandial, free plasma amino acid concentrations in rainbow trout (Oncorhynchus mykiss)

    DEFF Research Database (Denmark)

    Larsen, Bodil Katrine; Dalsgaard, Anne Johanne Tang; Pedersen, Per Bovbjerg

    2012-01-01

    was higher in the VEG diet than in the FM diet (93 versus 92%; t-test, Pb0.05), supporting that protease inhibitors from plant protein ingredients were not the cause of the delay. The apparent digestibility coefficient of carbohydrates (calculated as nitrogen-free extract (NFE)) was much lower in the VEG......Postprandial patterns in plasma free amino acid concentrations were investigated in juvenile rainbow trout (Oncorhynchus mykiss) fed either a fish meal based diet (FM) or a diet (VEG) where 59% of fish meal protein (corresponding to 46% of total dietary protein) was replaced by a matrix of plant...... proteins from wheat, peas, field beans, sunflower and soybean. Blood samples were obtained from the caudal vein of 7 fish in each dietary treatment group prior to feeding, as well as: 2, 4, 6, 8, 12, 24, 48 and 72 h after feeding (sampling 7 new fish at each time point), and plasma amino acid...

  3. Evolution of Conifer Diterpene Synthases: Diterpene Resin Acid Biosynthesis in Lodgepole Pine and Jack Pine Involves Monofunctional and Bifunctional Diterpene Synthases1[W][OA

    Science.gov (United States)

    Hall, Dawn E.; Zerbe, Philipp; Jancsik, Sharon; Quesada, Alfonso Lara; Dullat, Harpreet; Madilao, Lina L.; Yuen, Macaire; Bohlmann, Jörg

    2013-01-01

    Diterpene resin acids (DRAs) are major components of pine (Pinus spp.) oleoresin. They play critical roles in conifer defense against insects and pathogens and as a renewable resource for industrial bioproducts. The core structures of DRAs are formed in secondary (i.e. specialized) metabolism via cycloisomerization of geranylgeranyl diphosphate (GGPP) by diterpene synthases (diTPSs). Previously described gymnosperm diTPSs of DRA biosynthesis are bifunctional enzymes that catalyze the initial bicyclization of GGPP followed by rearrangement of a (+)-copalyl diphosphate intermediate at two discrete class II and class I active sites. In contrast, similar diterpenes of gibberellin primary (i.e. general) metabolism are produced by the consecutive activity of two monofunctional class II and class I diTPSs. Using high-throughput transcriptome sequencing, we discovered 11 diTPS from jack pine (Pinus banksiana) and lodgepole pine (Pinus contorta). Three of these were orthologous to known conifer bifunctional levopimaradiene/abietadiene synthases. Surprisingly, two sets of orthologous PbdiTPSs and PcdiTPSs were monofunctional class I enzymes that lacked functional class II active sites and converted (+)-copalyl diphosphate, but not GGPP, into isopimaradiene and pimaradiene as major products. Diterpene profiles and transcriptome sequences of lodgepole pine and jack pine are consistent with roles for these diTPSs in DRA biosynthesis. The monofunctional class I diTPSs of DRA biosynthesis form a new clade within the gymnosperm-specific TPS-d3 subfamily that evolved from bifunctional diTPS rather than monofunctional enzymes (TPS-c and TPS-e) of gibberellin metabolism. Homology modeling suggested alterations in the class I active site that may have contributed to their functional specialization relative to other conifer diTPSs. PMID:23370714

  4. Evolution of conifer diterpene synthases: diterpene resin acid biosynthesis in lodgepole pine and jack pine involves monofunctional and bifunctional diterpene synthases.

    Science.gov (United States)

    Hall, Dawn E; Zerbe, Philipp; Jancsik, Sharon; Quesada, Alfonso Lara; Dullat, Harpreet; Madilao, Lina L; Yuen, Macaire; Bohlmann, Jörg

    2013-02-01

    Diterpene resin acids (DRAs) are major components of pine (Pinus spp.) oleoresin. They play critical roles in conifer defense against insects and pathogens and as a renewable resource for industrial bioproducts. The core structures of DRAs are formed in secondary (i.e. specialized) metabolism via cycloisomerization of geranylgeranyl diphosphate (GGPP) by diterpene synthases (diTPSs). Previously described gymnosperm diTPSs of DRA biosynthesis are bifunctional enzymes that catalyze the initial bicyclization of GGPP followed by rearrangement of a (+)-copalyl diphosphate intermediate at two discrete class II and class I active sites. In contrast, similar diterpenes of gibberellin primary (i.e. general) metabolism are produced by the consecutive activity of two monofunctional class II and class I diTPSs. Using high-throughput transcriptome sequencing, we discovered 11 diTPS from jack pine (Pinus banksiana) and lodgepole pine (Pinus contorta). Three of these were orthologous to known conifer bifunctional levopimaradiene/abietadiene synthases. Surprisingly, two sets of orthologous PbdiTPSs and PcdiTPSs were monofunctional class I enzymes that lacked functional class II active sites and converted (+)-copalyl diphosphate, but not GGPP, into isopimaradiene and pimaradiene as major products. Diterpene profiles and transcriptome sequences of lodgepole pine and jack pine are consistent with roles for these diTPSs in DRA biosynthesis. The monofunctional class I diTPSs of DRA biosynthesis form a new clade within the gymnosperm-specific TPS-d3 subfamily that evolved from bifunctional diTPS rather than monofunctional enzymes (TPS-c and TPS-e) of gibberellin metabolism. Homology modeling suggested alterations in the class I active site that may have contributed to their functional specialization relative to other conifer diTPSs.

  5. Phytic acid concentration influences iron bioavailability from biofortified beans in Rwandese women with low iron status.

    Science.gov (United States)

    Petry, Nicolai; Egli, Ines; Gahutu, Jean B; Tugirimana, Pierrot L; Boy, Erick; Hurrell, Richard

    2014-11-01

    The common bean is a staple crop in many African and Latin American countries and is the focus of biofortification initiatives. Bean iron concentration has been doubled by selective plant breeding, but the additional iron is reported to be of low bioavailability, most likely due to high phytic acid (PA) concentrations. The present study evaluated the impact of PA on iron bioavailability from iron-biofortified beans. Iron absorption, based on erythrocyte incorporation of stable iron isotopes, was measured in 22 Rwandese women who consumed multiple, composite bean meals with potatoes or rice in a crossover design. Iron absorption from meals containing biofortified beans (8.8 mg Fe, 1320 mg PA/100 g) and control beans (5.4 mg Fe, 980 mg PA/100 g) was measured with beans containing either their native PA concentration or with beans that were ∼50% dephytinized or >95% dephytinized. The iron concentration of the cooked composite meals with biofortified beans was 54% higher than in the same meals with control beans. With native PA concentrations, fractional iron absorption from the control bean meals was 9.2%, 30% higher than that from the biofortified bean meals (P bean meals (406 μg) was 19% higher (P bean meals. With ∼50% and >95% dephytinization, the quantity of iron absorbed from the biofortified bean meals increased to 599 and 746 μg, respectively, which was 37% (P bean meals. PA strongly decreases iron bioavailability from iron-biofortified beans, and a high PA concentration is an important impediment to the optimal effectiveness of bean iron biofortification. Plant breeders should focus on lowering the PA concentration of high-iron beans. This trial was registered at clinicaltrials.gov as NCT01521273. © 2014 American Society for Nutrition.

  6. Fogging low concentrated organic acid in a fattening pig unit - Effect on animal health and microclimate.

    Science.gov (United States)

    Stein, Heiko; Schulz, Jochen; Kemper, Nicole; Tichy, Alexander; Krauss, Ines; Knecht, Christian; Hennig-Pauka, Isabel

    2016-12-23

    In intensive pig production aerial contaminates are potential hazards for the health of animals and humans. In this study, the effect of fogging a low concentrated tartaric acid solution on pigs' health, environmental and hygiene parameters were evaluated in an inhabited fattening unit. Pigs were housed in separate units (control group n=109 and experimental group n=110). During the whole fattening period, twice a week at 48 hour intervals, a 0.1% tartaric acid solution was aerosolized by a cold-fogging system for 20 minutes in the experimental unit. Environmental parameters were spot-checked on days of fogging. Sedimentation dust and surfaces were analysed for bacterial and fungal load. Dust particle size distribution was assessed. Pigs were clinically examined weekly. Standard meat examination at an abattoir was extended by individual quantification of lung alterations. The fogging procedure had no influence on ammonia concentrations. A significant reduction of mould, but not of bacteria, was found in sedimentation dust, and bacterial and mould scores of surface samples were improved. A significant reduction of particle size classes 1.6-2.0 µm, 4.0-5.0 µm, 7.5-10 µm, as well as 10-15 µm was observed. The high sound level of the fogging machine (82-102 dB) led to higher activity and pen-mate directed behaviour. More skin alterations, conjunctivitis and sneezing were recorded in the experimental group. Gross pathological lung alterations did not differ between both groups. Although fogging of tartaric acid is limited to a concentration of 0.1% due to its irritating effect on the respiratory mucosa, reduction of microbial load can be achieved, but it would be enhanced by using more powerful fogging systems.

  7. Low unesterified:esterified eicosapentaenoic acid (EPA) plasma concentration ratio is associated with bipolar disorder episodes, and omega-3 plasma concentrations are altered by treatment.

    Science.gov (United States)

    Saunders, Erika Fh; Reider, Aubrey; Singh, Gagan; Gelenberg, Alan J; Rapoport, Stanley I

    2015-11-01

    Omega (n)-3 and n-6 polyunsaturated fatty acids (PUFAs) are molecular modulators of neurotransmission and inflammation. We hypothesized that plasma concentrations of n-3 PUFAs would be lower and those of n-6 PUFAs higher in subjects with bipolar disorder (BD) compared to healthy controls (HCs), and would correlate with symptom severity in subjects with BD, and that effective treatment would correlate with increased n-3 but lower n-6 PUFA levels. Additionally, we explored clinical correlations and group differences in plasma levels of saturated and monounsaturated fatty acids. This observational, parallel group study compared biomarkers between HCs (n = 31) and symptomatic subjects with BD (n = 27) when ill and after symptomatic recovery (follow-up). Plasma concentrations of five PUFAs [linoleic acid (LA), arachidonic acid (AA), alpha-linolenic acid (ALA), docosahexaenoic acid (DHA), and eicosapentaenoic acid (EPA)], two saturated fatty acids (palmitic acid and stearic acid) and two monounsaturated fatty acids (palmitoleic acid and oleic acid) were measured in esterified (E) and unesterified (UE) forms. Calculated ratios included UE:E for the five PUFAs, ratios of n-3 PUFAs (DHA:ALA, EPA:ALA and EPA:DHA), and the ratio of n-6:n-3 AA:EPA. Comparisons of plasma fatty acid levels and ratios between BD and HC groups were made with Student t-tests, and between the BD group at baseline and follow-up using paired t-tests. Comparison of categorical variables was performed using chi-square tests. Pearson's r was used for bivariate correlations with clinical variables, including depressive and manic symptoms, current panic attacks, and psychosis. UE EPA was lower in subjects with BD than in HCs, with a large effect size (Cohen's d = 0.86, p acid level or ratio correlated with self-reported n-3 PUFA intake or use of medication by class. A large effect size of reduced UE EPA, and a lower plasma UE:E concentration ratio of EPA in the symptomatic BD state may be important factors

  8. Suitable Concentrations of Uric Acid Can Reduce Cell Death in Models of OGD and Cerebral Ischemia-Reperfusion Injury.

    Science.gov (United States)

    Zhang, Bin; Yang, Ning; Lin, Shao-Peng; Zhang, Feng

    2017-07-01

    Cerebral infarction (CI) is a common clinical cerebrovascular disease, and to explore the pathophysiological mechanisms and seek effective treatment means are the hotspot and difficult point in medical research nowadays. Numerous studies have confirmed that uric acid plays an important role in CI, but the mechanism has not yet been clarified. When treating HT22 and BV-2 cells with different concentrations of uric acid, uric acid below 450 μM does not have significant effect on cell viability, but uric acid more than 500 μM can significantly inhibit cell viability. After establishing models of OGD (oxygen-glucose deprivation) with HT22 and BV-2 cells, uric acid at a low concentration (50 μM) cannot improve cell viability and apoptosis, and Reactive oxygen species (ROS) levels during OGD/reoxygenation; a suitable concentration (300 μM) of uric acid can significantly improve cell viability and apoptosis, and reduce ROS production during OGD/reoxygenation; but a high concentration (1000 μM) of uric acid can further reduce cell viability and enhance ROS production. After establishing middle cerebral artery occlusion of male rats with suture method, damage and increase of ROS production in brain tissue could be seen, and after adding suitable concentration of uric acid, the degree of brain damage and ROS production was reduced. Therefore, different concentrations of uric acid should have different effect, and suitable concentrations of uric acid have neuroprotective effect, and this finding may provide guidance for study on the clinical curative effect of uric acid.

  9. Procedure for recovery from an uranium containing concentrate and phosphoric acid, as well as an uranium containing concentrate and phosphoric acid obtained by this procedure

    International Nuclear Information System (INIS)

    1980-01-01

    The phosphate ore is dissolved in sulphuric acid and the formed calcium sulphate is separated from the solution. The uranium is then precipitated by adding ammonium fluoride solution to the remaining phosphoric acid solution. When the phosphate ore is dissolved in sulphuric acid, fluorine gas is liberated and this is then used to produce the ammonium fluoride solution. (Th.P.)

  10. Studying Room Temperature Curing of Phenolic Resin and their Composites

    Directory of Open Access Journals (Sweden)

    M.H. Beheshty

    2007-10-01

    Full Text Available Phenolic resins are synthetic low molecular weight thermoset resins which are polymerized and cured to higher molecular weights by condensation method. These resins have high weathering resistance, high oxidative thermal properties and good chemical resistance. Phenolic resins can be cured thermally or by acid curing. The most common method of curing phenolic resin is by thermal curing that takes place in the range of 130-180oC. At room temperature, however, phenolic resins are cured by acid catalysts. In this paper, room temperature curing of resol phenolic resin by para toluene sulphonic acid has been investigated. The acid quantity has been determined for room temperature curing of two types of resols to achieve a reasonable hardness and gelation time. Temperature curing and thermal stability of respective resins have been investigated by DSC and TGA, respectively. A glass-phenolic composite plate has been prepared and cured by these two methods. The results show that the optimum amount of acid is 20% by weight. Optimum mechanical properties, chemical resistance and thermal properties have been achieved for acid cured system. The hot cured resin, however, has better properties.

  11. Comparaison structurale des acides humiques et du concentré de ...

    African Journals Online (AJOL)

    Abstract. De nombreux travaux ont été développés sur l'étude de la matière organique contenue dans le phosphate naturel de Youssoufia. ... Nous avons également étudié la cinétique de dégagement des gaz émanants des acides humiques et du concentré de kérogène, extraits de la matière organique. Nous nous ...

  12. Method for curing alkyd resin compositions by applying ionizing radiation

    International Nuclear Information System (INIS)

    Watanabe, T.; Murata, K.; Maruyama, T.

    1975-01-01

    An alkyd resin composition is prepared by dissolving a polymerizable alkyd resin having from 10 to 50 percent of oil length into a vinyl monomer. The polymerizable alkyd resin is obtained by a half-esterification reaction of an acid anhydride having a polymerizable unsaturated group and an alkyd resin modified with conjugated unsaturated oil having at least one reactive hydroxyl group per one molecule. The alkyd resin composition thus obtained is coated on an article, and ionizing radiation is applied on the article to cure the coated film thereon. (U.S.)

  13. Estimation of very low concentrations of Ruthenium by spectrophotometric method using barbituric acid as complexing agent

    International Nuclear Information System (INIS)

    Ramakrishna Reddy, S.; Srinivasan, R.; Mallika, C.; Kamachi Mudali, U.; Natarajan, R.

    2012-01-01

    Spectrophotometric method employing numerous chromogenic reagents like thiourea, 1,10-phenanthroline, thiocyanate and tropolone is reported in the literature for the estimation of very low concentrations of Ru. A sensitive spectrophotometric method has been developed for the determination of ruthenium in the concentration range 1.5 to 6.5 ppm in the present work. This method is based on the reaction of ruthenium with barbituric acid to produce ruthenium(ll)tris-violurate, (Ru(H 2 Va) 3 ) -1 complex which gives a stable deep-red coloured solution. The maximum absorption of the complex is at 491 nm due to the inverted t 2g → Π(L-L ligand) electron - transfer transition. The molar absorptivity of the coloured species is 9,851 dm 3 mol -1 cm -1

  14. Characterization of linoleic acid (C18:2) concentration in commercial corn silage and grain hybrids.

    Science.gov (United States)

    Baldin, M; Ying, Y; Fan, Y; Roth, G; Casper, D P; Harvatine, K J

    2018-01-01

    Corn silage and high-moisture corn grain are commonly recognized as risk factors for biohydrogenation-induced milk fat depression and may be due to the high concentration of linoleic acid (C18:2) in corn. Corn silage and corn grain have a low concentration of fatty acids (FA), but due to their high inclusion rate in diets they contribute substantially to unsaturated FA intake. The first objective of this study was to characterize the contribution of individual plant parts to total FA in whole-plant chopped corn. The second objective was to characterize the variation in FA profile in commercial silage and grain hybrids and evaluate the relationship between FA profile and other nutrients. To determine the location of FA in the corn plant, 4 stalks from 4 different commercial hybrids were separated into stalk, husk and shank, leaves, cob, and kernels. On a dry matter basis, 80.5% of total FA were in the kernels, 11.8% in the leaves, 5.1% in the stalk, 1.7% in the cob, and 1.0% in the husk and shank. More than 96% of the oleic acid (C18:1) and 92.5% of the C18:2 was in the kernels, whereas 71.0% of the linolenic acid (C18:3) was in the leaves. Next, the FA composition of fresh whole-plant chopped corn from 124 silage hybrids and grain from 72 grain hybrids was determined over 2 yr from test plots in Pennsylvania. Last, to extend the characterization, FA composition of whole-plant corn silage from 45 hybrids grown in test plots in South Dakota were characterized. In the fresh whole-plant chopped corn from PA test plots, C18:2 as a percentage of total FA averaged from 48.7% in 2013 (percentiles: 10th = 45.2, 90th = 52.2) and 48.0% in 2014 (percentiles: 10th = 44.1, 90th = 49.4). Concentration of C18:2 in corn grain averaged 57.5% in the 2013 (percentiles: 10th = 53.4, 90th = 60.8) and 56.1% in 2014 (percentiles: 10th = 53.5, 90th = 59.4). In the corn silage from South Dakota, the concentration of C18:2 as percentage of total FA averaged 45.4% (percentiles: 10th = 39

  15. Concentration Dependent Influence of Lipopolysaccharides on Separation of Hoof Explants and Supernatant Lactic Acid Concentration in an Ex Vivo/In Vitro Laminitis Model.

    Directory of Open Access Journals (Sweden)

    Nicole Reisinger

    Full Text Available Laminitis is one of the most common diseases in horses. It is not only painful for the animal, but also has a significant financial impact on the equine industry. This multifactorial disease affects the connective tissue of the hoof. However, the pathogenesis of laminitis is still not fully understood. Endotoxins, also known as lipopolysaccharides (LPS, and bacterial exotoxins seem to play an important role during the development of laminitis. The aim of our study was to investigate the effect of increasing LPS concentrations (0, 2.5, 5, 10, and 100 μg/mL on cell viability of isolated epidermal and dermal hoof cells as well as on the tissue integrity of hoof explants. Furthermore, glucose, acetic acid, lactic acid, and propionic acid concentrations in explant supernatants were measured to evaluate the energy metabolism in the hoof tissue. LPS did not exhibit cytotoxic effects on epidermal or dermal cells. Force required to separate LPS treated hoof explants decreased in a concentration dependent manner. Specifically, explants incubated with 10 and 100 μg/mL needed significantly less force to separate compared to control explants. Lactic acid concentrations were significantly decreased in explants incubated with 5, 10, or 100 μg/mL LPS, while glucose, acetic acid and propionic acid concentrations were unaffected by LPS treatment. Our study indicates that LPS has no cytotoxic effect on epidermal and dermal cells isolated from hoof tissue, but impairs integrity of hoof explants. In addition, LPS led to an alteration of the lactic acid production in the lamellar tissue. Since our data highlight that LPS can affect the integrity of the equine hoof tissue in vitro, endotoxins should be further explored for their contribution to facilitate the development of laminitis.

  16. Estimate of serum immunoglobulin G concentration using refractometry with or without caprylic acid fractionation.

    Science.gov (United States)

    Morrill, K M; Polo, J; Lago, A; Campbell, J; Quigley, J; Tyler, H

    2013-07-01

    Objectives of this study were to develop a rapid calf-side test to determine serum IgG concentrations using caprylic acid (CA) fractionation, followed by refractometry of the IgG-rich supernatant and compare the accuracy of this method with results obtained using refractometry using raw serum. Serum samples (n=200) were obtained from 1-d-old calves, frozen (-20°C), and shipped to the laboratory. Samples were allowed to thaw for 1h at room temperature. Fractionation with CA was conducted by adding 1mL of serum to a tube containing 45, 60, or 75µL of CA and 0.5, 1.0, or 1.5mL of 0.06 M acetic acid. The tube contents were mixed well, allowed to react for 1 min, and then centrifuged at 3,300 × g for 0, 10, or 20 min at 25°C. The %Brix and refractive index of the fractionated supernatant were determined using a digital refractometer. Nonfractionated serum was analyzed for %Brix (BRn), refractive index (nDn), and IgG concentration by radial immunodiffusion. The mean serum IgG concentration was 19.0 mg/mL [standard deviation (SD)=9.7], with a range of 3.5 to 47.0 mg/mL. The mean serum BRn was 8.6 (SD=0.91), with a range of 6.8 to 11.0. The mean serum nDn was 1.34566 (SD=0.00140), with a range of 1.34300 to 1.34930. Serum nDn was positively correlated with IgG concentration (correlation coefficient=0.86; n=185). Fractionated samples treated with 1mL 0.6 M acetic acid and 60µL of CA and not centrifuged before analysis resulted in a strong relationship between the refractive index of the fractionated supernatant and IgG (correlation coefficient=0.80; n=45). Regression was used to determine cut points indicative of 10, 12, and 14 mg of IgG/mL to determine the sensitivity and specificity of refractometry to identify failure of passive transfer (serum IgG refractometry of nonfractionated calf serum provides a strong estimate of IgG concentration and 7.8% Brix may be used as the cut point to identify failure of passive transfer in 1-d-old calves. Copyright © 2013 American

  17. Estimating naphthenic acids concentrations in laboratory-exposed fish and in fish from the wild.

    Science.gov (United States)

    Young, Rozlyn F; Wismer, Wendy V; Fedorak, Phillip M

    2008-09-01

    Naphthenic acids (NAs) are the most water-soluble organic components found in the Athabasca oil sands in Alberta, Canada, and these acids are released into aqueous tailing waters as a result of bitumen extraction. Although the toxicity of NAs to fish is well known, there has been no method available to estimate NAs concentrations in fish. This paper describes a newly developed analytical method using single ion monitoring gas chromatography-mass spectrometry (GC-MS) to measure NAs in fish, down to concentrations of approximately 0.1mgkg(-1) of fish flesh. This method was used to measure the uptake and depuration of commercial NAs in laboratory experiments. Exposure of rainbow trout (Oncorhynchus mykiss) to 3mg NAsl(-1) for 9d gave a bioconcentration factor of approximately 2 at pH 8.2. Within 1d after the fish were transferred to NAs-free water, about 95% of the NAs were depurated. In addition, the analytical method was used to determine if NAs were present in four species of wild fish - northern pike (Esox lucius), lake whitefish (Coregonus clupeaformis), white sucker (Catostomus commersoni), walleye (Sander vitreus) - collected from near the oil sands. Flesh samples from 23 wild fish were analyzed, and 18 of these had no detectable NAs. Four fish (one of each species) contained NAs at concentrations from 0.2 to 2.8mgkg(-1). The GC-MS results from one wild fish presented a unique problem. However, with additional work it was concluded that the NAs concentration in this fish was <0.1mgkg(-1).

  18. Effect of ammonium sulfate addition on decomposition of eudiolitic concentrate of sulphuric acid

    International Nuclear Information System (INIS)

    Ermakova, E.V.; Kolenkova, M.A.; Egorov, B.L.

    1985-01-01

    Researches on eudiolitic concentrate sulization by the sulfuric acid and ammonnum sulfate mixture are conducted with the purpose of a more complete separation of the rare-earth elements from Nb and Zr. It is shown that the eudiolitic concentrate decomposition degree under similar circumstances does not depend significantly on the amount of the added (NH 4 ) 2 SO 4 . Rare-earth element and especially Y 2 O 3 transition into solution reduces sharply. As a result of investigations the following optimal eudiolitic concentrate sulfatization regime is recommended: the process temperature is 230 deg C; the duration is 4 hours; the consumption of 50% H 2 SO 4 -110% of the amount theore,.ically required for the break-down of all the components; the amount of (NH 4 ) 2 SO 4 - 60 % of the concentrate weight. This regime allows more or less complete separation of ZrO 2 and Nb 2 O 5 from the rare-earth elements sum

  19. Review: Resin Composite Filling

    Directory of Open Access Journals (Sweden)

    Desmond Ng

    2010-02-01

    Full Text Available The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin composite has aesthetic advantages over amalgam, one of the major disadvantage include polymerization shrinkage and future research is needed on reaction kinetics and viscoelastic behaviour to minimize shrinkage stress.

  20. Review: Resin Composite Filling

    Science.gov (United States)

    Chan, Keith H. S.; Mai, Yanjie; Kim, Harry; Tong, Keith C. T.; Ng, Desmond; Hsiao, Jimmy C. M.

    2010-01-01

    The leading cause of oral pain and tooth loss is from caries and their treatment include restoration using amalgam, resin, porcelain and gold, endodontic therapy and extraction. Resin composite restorations have grown popular over the last half a century because it can take shades more similar to enamel. Here, we discuss the history and use of resin, comparison between amalgam and resin, clinical procedures involved and finishing and polishing techniques for resin restoration. Although resin composite has aesthetic advantages over amalgam, one of the major disadvantage include polymerization shrinkage and future research is needed on reaction kinetics and viscoelastic behaviour to minimize shrinkage stress.

  1. The serum uric acid concentration is not causally linked to diabetic nephropathy in type 1 diabetes.

    Science.gov (United States)

    Ahola, Aila J; Sandholm, Niina; Forsblom, Carol; Harjutsalo, Valma; Dahlström, Emma; Groop, Per-Henrik

    2017-05-01

    Previous studies have shown a relationship between uric acid concentration and progression of renal disease. Here we studied causality between the serum uric acid concentration and progression of diabetic nephropathy in 3895 individuals with type 1 diabetes in the FinnDiane Study. The renal status was assessed with the urinary albumin excretion rate and estimated glomerular filtration rate (eGFR) at baseline and at the end of the follow-up. Based on previous genomewide association studies on serum uric acid concentration, 23 single nucleotide polymorphisms (SNPs) with good imputation quality were selected for the SNP score. This score was used to assess the causality between serum uric acid and renal complications using a Mendelian randomization approach. At baseline, the serum uric acid concentration was higher with worsening renal status. In multivariable Cox regression analyses, baseline serum uric acid concentration was not independently associated with progression of diabetic nephropathy over a mean follow-up of 7 years. However, over the same period, baseline serum uric acid was independently associated with the decline in eGFR. In the cross-sectional logistic regression analyses, the SNP score was associated with the serum uric acid concentration. Nevertheless, the Mendelian randomization showed no causality between uric acid and diabetic nephropathy, eGFR categories, or eGFR as a continuous variable. Thus, our results suggest that the serum uric acid concentration is not causally related to diabetic nephropathy but is a downstream marker of kidney damage. Copyright © 2016 International Society of Nephrology. Published by Elsevier Inc. All rights reserved.

  2. Influence of lactose hydrolysis and solids concentration on alcohol production by yeast in acid whey ultrafiltrate

    Energy Technology Data Exchange (ETDEWEB)

    O' leary, V.S.; Sutton, C.; Bencivengo, M.; Sullivan, B.; Holsinger, V.H.

    1977-11-01

    Alcohol yields of 6.5 percent were obtained with Saccharomyces cerevisiae in lactase-hydrolyzed acid whey permeate containing 30 to 35 percent total solids. Maximum alcohol yields obtained with Kluyveromyces fragilis were 4.5 percent in lactase-hydrolyzed acid whey permeate at a solids concentration of 20 percent and 3.7 percent in normal permeate at a solids concentration of 10 percent. Saccharomyces cerevisiae efficiently converted the glucose present in lactase-hydrolyzed whey permeates containing 5 to 30 percent total solids (2 to 13 percent glucose) to alcohol. However, the galactose, which comprised about half the available carbohydrate in lactase-hydrolyzed whey, was not utilized by S. cerevisiae, so that even though alcohol yields were higher when this organism was used, the process was wasteful in that a substantial proportion of the substrate was not fermented. For the process to become commercially feasible, an efficient means of rapidly converting both the galactose and glucose to alcohol must be found.

  3. Copper solvent extraction from chalcopyrite concentrate acid leach solutions by LIX 984

    Directory of Open Access Journals (Sweden)

    Elamari K.

    2006-01-01

    Full Text Available Copper production from ores or sulphide concentrates is classically realized by pyrometallurgical route. In this study, hydrometallurgical treatment of a copper sulphide concentrate, provided by Hajar Mine (ONA-Group, Morocco, was tested by using a mixture of nitric and hexafluorosilicic acids. Copper is present in the solid product as chalcopyrite and its amount is 28.1 % by weight. Leaching stage allows to dissolve more than 90% of copper witch is accompanied, in the same averages, by Zn and Fe. The leach solution obtained has pH = 0.6 and Eh = 580 mV/ENH and contains 19.3 g/L Cu, 18.1 g/L Fe, 4.5 g/L Zn and 0.03 g/L Pb. The recovery of copper from this leach solution was curried out by solvent extraction using Lix 984, diluted in Escaid 110. McCabe - Thiele distribution isotherms showed that at pH 1.7 total and selective copper extraction can be realized with Øo:Øa =1.5:1 in 3 extraction stages. Stripping of the loaded copper by treating the organic phases was easily obtained by a sulphuric acid solution.

  4. Using Spectrophotometric Titrations To Characterize Humic Acid Reactivity at Environmental Concentrations

    International Nuclear Information System (INIS)

    Janot, N.; Benedetti, M. F.; Janot, N.; Reiller, P. E.; Korshin, G. V.

    2010-01-01

    Potentiometric titration is a common method to characterize dissolved organic matter (DOM) reactivity. Because of the sensitivity of pH electrodes, it is necessary to work with very high DOM (≥1 g/L) concentrations that are unrealistic compared to those found in natural waters (0. 1 to 100 mg/L). To obtain proton binding data for concentrations closer to environmental values, spectroscopic titration methodology is a viable alternative to traditional potentiometric titrations. Spectrophotometric titrations and UV visible spectra of a diluted solution of purified Aldrich humic acid (5 mg(DOC)/L) are used to estimate changes in proton binding moieties as function of pH and ionic strength after calculation of differential absorbance spectra variations. After electrostatic correction of spectrophotometric data, there is a linear operational correlation between spectrophotometric and potentiometric data which can be used as a transfer function between the two properties. Spectrophotometric titrations are then used to determine the changes of humic acid protonation after adsorption onto alpha-alumina. (authors)

  5. Influence of deficit irrigation strategies on fatty acid and tocopherol concentration of almond (Prunus dulcis).

    Science.gov (United States)

    Zhu, Ying; Taylor, Cathy; Sommer, Karl; Wilkinson, Kerry; Wirthensohn, Michelle

    2015-04-15

    The effects of deficit irrigation on almond fatty acid and tocopherol levels were studied in a field trial. Mature almond trees were subjected to three levels of deficit irrigation (85%, 70% and 55% of potential crop evapotranspiration (ETo), as well as control (100% ETo) and over-irrigation (120% ETo) treatments. Two deficit irrigation strategies were employed: regulated deficit irrigation (RDI) and sustained deficit irrigation (SDI). Moderate deficit irrigation (85% RDI and 85% SDI) had no detrimental impact on almond kernel lipid content, but severe and extreme deficiencies (70% and 55%) influenced lipid content. Unsaturated fatty acid (USFA) and saturated fatty acid (SFA) contents fluctuated under these treatments, the oleic/linoleic ratio increased under moderate water deficiency, but decreased under severe and extreme water deficiency. Almond tocopherols concentration was relatively stable under deficit irrigation. The variation between years indicated climate has an effect on almond fruit development. In conclusion it is feasible to irrigate almond trees using less water than the normal requirement, without significant loss of kernel quality. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. GLUCOSE, TOTAL PROTEINS, URIC ACID AND TRIGL YCERIDES CONCENTRATIONS IN BLOOD OF ATIVE LAYING HENS

    Directory of Open Access Journals (Sweden)

    Bashir Mahmood Bhatti, Tanzeela Talat and Rozina Sardar

    2001-09-01

    Full Text Available This study was undertaken, to estimate levels of glucose, total proteins, albumins, uric acid and triglycerides in plasma of Desi and Naked Neck laying hens. The experimental birds received ration containing 16 per cent crude protein and were housed in open sheds. The mean values (mg/dL observed in Desi hens were 226.736+15.20 glucose, 1.624+0.224 albumin, 5.203+1.078 total proteins, 4.633+1.875 uric acid and 529.800+554.74 triglycerides. In Naked neck hens, the mean values were found to be 231.818+31.376 glucose, 1.562+0.287 albumins, 4.533+0.797total proteins, 4.157+1.336 uric acid and 791.200+320.474 triglycerides. There was no difference (P<0.05 in mean values of blood parameters between both the native laying hens which suggested that in identical genetical mechanism regulated concentrations of blood chemical constituents under study.

  7. Concentration of fulvic acid in the growth bands of hermatypic corals in relation to local precipitation

    Science.gov (United States)

    Fang, Lee-Shing; Chou, Yi-Cheng

    1992-12-01

    Coral growth rate and the concentrations of fulvic acid in the growth bands of the hermatypic coral Porites lutea Edwards & Haime and Favia maxima Veron were investigated in samples taken from 1986 to 1988 in the waters of southern Taiwan (22°05'≈36'N, 120°24'≈50'E). These were analyzed against the local annual precipitation, the locality of the sampling sites, the construction activity on nearby land and coral species. The results showed that the annual growth rate of P. lutea was 1.08±0.12 cm while F. maxima was 0.83±0.09 cm. The amount of fulvic acid incorporated in the growth band was positively correlated with the local annual precipitation. However, the correlation coefficient varied from as high as 0.9519 to as low as 0.0921 due to different topographies of the sampling sites, dilution factors from the ocean and construction activities along the coast. F. maxima was found to be more sensitive than P. lutea in terms of fulvic acid uptake from the surrounding waters. The study of fluorescence in the skeleton of hermatypic corals is a reasonable approach to biomonitor the environment after consideration of local factors.

  8. Electrodialytic decontamination of spent ion exchange resins

    International Nuclear Information System (INIS)

    Nott, B.R.

    1982-01-01

    Development of a novel electrodialytic decontamination process for the selective removal of radioactive Cs from spent ion exchange resins containing large amounts of Li is described. The process involves passage of a dc electric current through a bed of the spent ion exchange resin in a specially designed electrodialytic cell. The radiocesium so removed from a volume of the spent resin is concentrated onto a much smaller volume of a Cs selective sorbent to achieve a significant radioactive waste volume reduction. Technical feasibility of the electrodialytic resin decontamination process has been demonstrated on a bench scale with a batch of simulated spent ion exchange resin and using potassium cobalt ferrocyanide as the Cs selective sorbent. A volume reduction factor between 10 and 17 has been estimated. The process appears to be economically attractive. Improvements in process economics can be expected from optimization of the process. Other possible applications of the EDRD process have been identified

  9. Water-lactose behavior as a function of concentration and presence of lactic acid in lactose model systems.

    Science.gov (United States)

    Wijayasinghe, Rangani; Vasiljevic, Todor; Chandrapala, Jayani

    2015-12-01

    The presence of high amounts of lactic acid in acid whey restricts its ability to be further processed because lactose appears to remain in its amorphous form. A systematic study is lacking in this regard especially during the concentration step. Hence, the main aim of the study was to establish the structure and behavior of water molecules surrounding lactose in the presence of 1% (wt/wt) lactic acid at a concentration up to 50% (wt/wt). Furthermore, the crystallization nature of freeze-dried lactose with or without lactic acid was established using differential scanning calorimetry and Fourier transform infrared spectroscopy. Two mechanisms were proposed to describe the behavior of water molecules around lactose molecules during the concentration of pure lactose and lactose solutions with lactic acid. Pure lactose solution exhibited a water evaporation enthalpy of ~679 J·g(-1), whereas lactose+ lactic acid solution resulted in ~965 J·g(-1) at a 50% (wt/wt) concentration. This indicates a greater energy requirement for water removal around lactose in the presence of lactic acid. Higher crystallization temperatures were observed with the presence of lactic acid, indicating a delay in crystallization. Furthermore, less crystalline lactose (~12%) was obtained in the presence of lactic acid, indicating high amorphous nature compared with pure lactose where ~50% crystallinity was obtained. The Fourier transform infrared spectra revealed that the strong hydration layer consisting lactic acid and H3O(+) ions surrounded lactose molecules via strong H bonds, which restricted water mobility, induced a change in structure of lactose, or both, creating unfavorable conditions for lactose crystallization. Thus, partial or complete removal of lactic acid from acid whey may be the first step toward improving the ability of acid whey to be processed. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  10. Triterpenoids of Resin of Schinus terebinthifolius and Their Anti-inflammatory Effects

    OpenAIRE

    Yasuhito, Nobushi; Taiki, Matsushita; Naoki, Oikawa; Yuzo, Okazaki; Shigetoshi, Tsutsumi; Masahiko, Kurokawa; Young Kun, Park; Ken, Yasukawa; School of Pharmacy, Nihon University; School of Pharmacy, Nihon University; School of Pharmacy, Nihon University; Amazonfood Ltd.; Amazonfood Ltd.; Department of Biochemistry, School of Pharmaceutical Sciences, Kyushu University of Health and Welfare; Department of Food Science, College of Food Engineering, State University of Campinas

    2014-01-01

    Inhibitory effects on 12-O-tetradecanoylphorbol-13-acetate (TPA)-induced inflammation in mice was observed in the methanol extract of the plant resin of Schinus terebinthifolius. Five known compounds were isolated from the resin of S. terebinthifolius: betulonic acid, moronic acid, 3-oxooleanolic acid, masticadienoic acid and anwuweizonic acid.

  11. Perfluoroalkyl Acid Concentrations in Livers of Fox (Vulpes vulpes) and Chamois (Rupicapra rupicapra) from Germany and Austria.

    Science.gov (United States)

    Riebe, Rika Alessa; Falk, Sandy; Georgii, Sebastian; Brunn, Hubertus; Failing, Klaus; Stahl, Thorsten

    2016-07-01

    The concentrations of 11 perfluorinated alkyl acids (PFAAs) were measured in the livers of foxes (Vulpes vulpes) from Germany, a primarily carnivorous species, and chamois (Rupicapra rupicapra) from Austria, an herbivorous species. Perfluorooctanesulfonate (PFOS) at concentrations [all results refer to wet weight (ww)] of 3.2-320 µg/kg were detected in all 40 fox livers tested, yielding an arithmetic mean of 46.6 µg/kg and a median of 29.8 µg/kg. Long-chain PFAAs were detected at concentrations of 1.7 µg/kg perfluorononanoic acid (PFNA) to 2.4 µg/kg perfluorodecanoic acid (PFDA) and perfluorododecanoic acid (PFDoDA). Of the short-chain PFAAs tested, only perfluorohexanoic acid (PFHxA) was found in 1 fox liver at a concentration of 1.4 µg/kg, and perfluorohexane sulfonate (PFHxS) was found in 2 fox livers at a concentration of 1 µg/kg each. PFOS and PFNA concentrations higher than limit of quantification (LOQ) were detected in 90.9 and 81.8 % of chamois livers, respectively. The arithmetic mean for PFOS concentrations was 2.2 µg/kg (median 2.4 µg/kg), a factor of 21 (median factor of 12) lower than in fox livers. The arithmetic mean for PFNA concentrations was 2.0 µg/kg (median 1.9 µg/kg). Perfluorobutanoic acid, PFHxA, perfluorooctanoic acid, perfluorobutanesulfonate, and PFHxS were not detected at concentrations higher than the LOQ in any of the samples. The various results are compared with one another and with the results of other studies of herbivorous, carnivorous, and omnivorous wild animals. The highest concentrations of PFAA, in particular PFOS, were found in omnivorous animals followed by carnivores. The lowest levels were present in herbivores.

  12. Concentration of gadolinium-diethylene triamine pentaacetic acid in human kidney

    International Nuclear Information System (INIS)

    Takeda, Masayuki; Katayama, Yasushi; Tsutsui, Toshiki; Komeyama, Takeshi; Mizusawa, Takaki; Tanikawa, Toshiki; Sato, Shotaro

    1993-01-01

    Although gadolinium diethylene triamine pentaacetic acid (Gd-DTPA) has been used as a contrast material in magnetic resonance imaging, it is known that contrast enhancement effect disappears if the concentration of Gd-DTPA increases beyond some levels. In this study, to evaluate the proper pulse sequences for dynamic magnetic resonance imaging (MRI) in the human kidney, the concentration of Gd-DTPA was quantitatively measured by inductively coupled plasma (ICP) emission spectrometry in human biological samples after administration of Gd-DTPA, and the signal intensity of MRI is the solution of several concentrations of Gd-DTPA was measured. In using a low magnetic field apparatus, signal intensity linearly correlated with the concentration of Gd-DTPA between 0 and 2.0 μmol/g under saturation recovery sequences (flip angle was 60deg or 90deg). Using a high magnetic field apparatus, signal intensity linearly correlated with the concentration of Gd-DTPA between 0 and 2.0 or 3.0 μmol/g under spin echo or gradient-echo sequences. Gd-DTPA concentration of the renal cortex ranged from 0.132 to 0.152 μmol/g tissue at 5 min after intravenous injection of Gd-DTPA 0.05 mmol/kg body weight in 7 patients with adrenal tumor or renal cell cancer, and 1 patient with both urinary bladder cancer and prostatic cancer. Seven of them showed normal renal function and the other had renal insufficiency (GFR 25 ml/min/1.48 m 2 ). Gd-DTPA concentrations of renal medulla and renal cell cancer tissue were 0.123 and 0.108 μmol/g tissue, respectively, at 5 min after intravenous injection of Gd-DTPA 0.05 mmol/kg body weight. These results suggest that the signal intensity of renal cortex, renal medulla, and renal cell cancer tissue may linearly correlate with Gd-DTPA concentration of tissues at 5 min after intravenous injection of Gd-DTPA 0.5 mmol/kg body weight. (author)

  13. Serum cobalamin, urinary methylmalonic acid and plasma homocysteine concentrations in healthy and cobalamin-deficient Border Collies

    OpenAIRE

    Lutz, S

    2011-01-01

    Hereditary cobalamin deficiency is suspected in the Border Collie breed. Diagnosis is based on hypocobalaminemia, hyperhomocysteinemia and methylmalonic aciduria. Goals of the study were (1) to establish reference values for the blood concentrations of cobalamin and homocysteine and for the concentration of urinary methylmalonic acid and (2) to screen a larger Border Collie population with the aforementioned markers. Cobalamin, homocysteine and methylmalonic acid were measured using an aut...

  14. [Analyze nanofiltration separation rule of chlorogenic acid from low concentration ethanol by Donnan effect and solution-diffusion effect].

    Science.gov (United States)

    Li, Cun-Yu; Liu, Li-Cheng; Jin, Li-Yang; Li, Hong-Yang; Peng, Guo-Ping

    2017-07-01

    To separate chlorogenic acid from low concentration ethanol and explore the influence of Donnan effect and solution-diffusion effect on the nanofiltration separation rule. The experiment showed that solution pH and ethanol volume percent had influences on the separation of chlorogenic acid. Within the pH values from 3 to 7 for chlorogenic acid in 30% ethanol, the rejection rate of chlorogenic acid was changed by 70.27%. Through the response surface method for quadratic regression model, an interaction had been found in molecule weight cut-off, pH and ethanol volume percent. In fixed nanofiltration apparatus, the existence states of chlorogenic acid determinedits separation rules. With the increase of ethanol concentration, the free form chlorogenic acid was easily adsorbed, dissolved on membrane surface and then caused high transmittance due to the solution-diffusion effect. However, at the same time, due to the double effects of Donnan effect and solution-diffusion effect, the ionic state of chlorogenic acid was hard to be adsorbed in membrane surface and thus caused high rejection rate. The combination of Box-Behnken design and response surface analysis can well optimize the concentrate process by nanofiltration, and the results showed that nanofiltration had several big advantages over the traditional vacuum concentrate technology, meanwhile, and solved the problems of low efficiency and serious component lossesin the Chinese medicines separation process for low concentration organic solvent-water solution. Copyright© by the Chinese Pharmaceutical Association.

  15. Multistage dilute acid leaching of a medium grade iron ore to super-concentrate

    Directory of Open Access Journals (Sweden)

    Adeleke A.A.

    2014-01-01

    Full Text Available The phosphorous laden Koton Karfe iron ore is a medium grade iron ore deposit in Nigeria that can be upgraded as a super-concentrate for use at the Aladja Steel Midrex plant. The 75 μm size sample fraction of the ore was preconcentrated with shaking table and leached in the oven at atmospheric pressure with dilute hydrochloric acid in single and multistage leaching sequences of H2O-HCl-H2O and HCl-H2O-H2O. The as-received, as-tabled and asleached samples were then subjected to X-ray fluorescence and microscopic analyses. The results obtained showed that the H2O-HCl-H2O route produced a higher grade concentrate that assayed 68.54% Fe indicating about 58% upgrade in iron content; while the phosphorus and sulphur contents were reduced by about 77 and 99.6% respectively. In addition, the silicon, manganese, and titanium contents were drastically reduced, while potassium was completely eliminated. The upgrade of iron content in the ore to 68.54% and the drastic reduction in phosphorous and sulphur contents has thus rendered the Koton Karfe iron ore suitable for use as a super concentrate for the Aladja steel plant direct reduction iron making process.

  16. Icosapent ethyl: Eicosapentaenoic acid concentration and triglyceride-lowering effects across clinical studies.

    Science.gov (United States)

    Bays, Harold E; Ballantyne, Christie M; Doyle, Ralph T; Juliano, Rebecca A; Philip, Sephy

    2016-09-01

    Icosapent ethyl is a high-purity prescription form of eicosapentaenoic acid (EPA) ethyl ester approved at a dose of 4g/day as an adjunct to diet to reduce triglyceride (TG) levels in adult patients with severe (≥500mg/dL) hypertriglyceridemia. This post-hoc exploratory analysis examined the relationship of icosapent ethyl dose with EPA concentrations in plasma and red blood cells (RBCs) across 3 clinical studies-a phase 1 pharmacokinetic study in healthy adult volunteers and 2 pivotal phase 3 studies (MARINE and ANCHOR) in adult patients with hypertriglyceridemia-and examined the relationship between EPA levels and TG-lowering effects in MARINE and ANCHOR. In all 3 studies, icosapent ethyl produced dose-dependent increases in the concentrations of EPA in plasma and RBCs. In both MARINE and ANCHOR, these dose-dependent EPA increases correlated with the degree of TG level lowering (all P170μg/mL and>70μg/mL, respectively. These studies support icosapent ethyl as producing predictable dose-dependent pharmacokinetics/pharmacodynamics, with TG level lowering dependent upon icosapent ethyl dose and EPA concentrations in plasma and RBCs. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  17. Serum uric acid concentrations and SLC2A9 genetic variation in Hispanic children: The Viva La Familia Study

    Science.gov (United States)

    Elevated concentrations of serum uric acid are associated with increased risk of gout and renal and cardiovascular diseases. Genetic studies in adults have consistently identified associations of solute carrier family 2, member 9 (SLC2A9), polymorphisms with variation in serum uric acid. However, it...

  18. Consumption of high doses of chlorogenic acid, present in coffee, or black tea increases plasma total homocysteine concentrations in humans

    NARCIS (Netherlands)

    Olthof, M.R.; Hollman, P.C.; Zock, P.L.; Katan, M.B.

    2001-01-01

    In population studies, high intakes of coffee are associated with raised concentrations of plasma homocysteine, a predictor of risk of cardiovascular disease. Chlorogenic acid is a major polyphenol in coffee; coffee drinkers consume up to 1 g chlorogenic acid/d. OBJECTIVE: We studied whether

  19. Effect of a protein-rich meal on urinary and salivary free amino acid concentrations in human subjects

    NARCIS (Netherlands)

    Brand, H. S.; Jörning, G. G.; Chamuleau, R. A.; Abraham-Inpijn, L.

    1997-01-01

    The aim of the present study was to investigate whether in healthy volunteers acute changes in plasma free amino acid composition after a protein-rich test meal are reflected in the urinary and salivary concentrations of the corresponding amino acids. The ingestion of a protein-rich meal elicited a

  20. Treatment method for stabilization of radioactive exchange resin

    International Nuclear Information System (INIS)

    Hideo, Oni; Takashi, Miyake; Hitoshi, Miyamoto; Toshio, Funakoshi; Yuzo, Inagaki.

    1988-01-01

    This is a method for eluting radioactive nuclides from a radioactive ion exchange resin in which it has been absorbed. First, the Cs in this resin is extracted using a neutral salt solution which contains Na + . The Cs that has been transferred to the neutral salt solution is absorbed and expelled by inorganic ion exchangers. Then the Co, Fe, Mn and Sr in said resin are eluted using an acidic solution; the Co, Fe, Mn and Sr that have been transferred to the acidic solution are separated from that solution by means of a diffusion dialysis vat. This process is a unique characteristic of this ion exchange resin treatment method. 1 fig

  1. Spectrophotometric flow injection catalytic determination of molybdenum in plant digest using ion exchange resin

    International Nuclear Information System (INIS)

    Pessenda, L.C.R.

    1987-03-01

    A spectrophotometric flow injection analytical method based on the catalytic action of molybdenum on the oxidation of iodide by hydrogen peroxide in acidic medium is proposed for the molybdenum determination in plant digests. A cation exchange resin column is incorporated into a flow injection system for removal of interferents. The following system variables were investigated and optimized: reagent concentrations, sample injection volume, mixing and reaction coil lengths, temperature, sampling time, pumping rate and concentration of eluting agents. The effects of interfering species and of the acidity of samples on the molybdenum retention by the ion exchange resin column were investigated. The proposed method is characterized by good precision (r.s.d. (2.0%), a sampling rate of about 40 samples per hour, and permits the determination of molybdenum in plant digests in the range 1.0 to 40.0 μg/l. The results compare well with those obtained by graphite furnace atomic absorption spectrometry. (author) [pt

  2. Radionuclide concentrations in raw and purified phosphoric acids from Brazil and their processing wastes: implications for radiation exposures.

    Science.gov (United States)

    da Conceição, Fabiano Tomazini; Antunes, Maria Lúcia Pereira; Durrant, Steven F

    2012-02-01

    Radionuclides from the U and Th natural series are present in alkaline rocks, which are used as feedstock in Brazil for the production of raw phosphoric acid, which can be considered as a NORM (naturally occurring radioactive material). As a result of the purification of raw phosphoric acid to food-grade phosphoric acid, two by-products are generated, i.e., solid and liquid wastes. Taking this into account, the main aim of this study was to evaluate the fluxes of natural radionuclide in the production of food-grade phosphoric acids in Brazil, to determine the radiological impact caused by ingestion of food-grade phosphoric acid, and to evaluate the solid waste environmental hazards caused by its application in crop soils. Radiological characterization of raw phosphoric acid, food-grade phosphoric acid, solid waste, and liquid waste was performed by alpha and gamma spectrometry. The (238)U, (234)U, (226)Ra, and (232)Th activity concentrations varied depending on the source of raw phosphoric acid. Decreasing radionuclides activity concentrations in raw phosphoric acids used by the producer of the purified phosphoric acid were observed as follows: Tapira (raw phosphoric acid D) > Catalão (raw phosphoric acids B and C) > Cajati (raw phosphoric acid A). The industrial purification process produces a reduction in radionuclide activity concentrations in food-grade phosphoric acid in relation to raw phosphoric acid produced in plant D and single raw phosphoric acid used in recent years. The most common use of food-grade phosphoric acid is in cola soft drinks, with an average consumption in Brazil of 72 l per person per year. Each liter of cola soft drink contains 0.5 ml of food-grade phosphoric acid, which gives an annual average intake of 36 ml of food-grade phosphoric acid per person. Under these conditions, radionuclide intake through consumption of food-grade phosphoric acid per year per person via cola soft drinks is not hazardous to human health in Brazil

  3. Raman study of the interactions between highly ordered pyrolytic graphite (HOPG and polyoxometalates: The effects of acid concentration

    Directory of Open Access Journals (Sweden)

    Vidoeski Bojan A.

    2016-01-01

    Full Text Available Heteropoly acids (HPAs found wide applications, such as in catalysis, energy conversion and storage, analytical chemistry, clinical medicine, materials science and others, but because of their low surface area and high solubility in water their use is limited. One of the possible ways to overcome these obstacles is to use height specific surface area support for HPAs, such as carbon nanomaterials. Raman spectroscopy was applied for studying study interaction between HPAs and highly ordered pyrolytic graphite (HOPG as a model of a support. HOPG was exposed to two different HPAs: 12-tungstophosphoric acid and 12-molybodphosphoric acid, at different concentrations. It was noticed that 12-molybodphosphoric acid has stronger effects on HOPG structure causing a weak doping and increase of structural disorder. It is supposed that HOPG interacts with especially external oxygen atoms of 12-molybodphosphoric acid. Atomic force microscopy showed that surface roughness of HOPG treated with 12-molybodphosphoric acid increases with increase of acid concentration, while in the case of HOPG exposed to 12-tungstophosphoric acid the surface roughness is not concentration dependent. The growth trend in measured surface roughness (RMS is in the agreement with the changes in the intensity ratio ID/IG obtained from Raman spectra of HOPG samples treated with 12-molybdophosphoric acid. [Projekat Ministarstva nauke Republike Srbije, br. 172003 i br. 172043

  4. Temporal Relationship Between Uric Acid Concentration and Risk of Diabetes in a Community-based Study Population

    Science.gov (United States)

    Juraschek, Stephen P.; McAdams-Demarco, Mara; Miller, Edgar R.; Gelber, Allan C.; Maynard, Janet W.; Pankow, James S.; Young, Hunter; Coresh, Josef; Selvin, Elizabeth

    2014-01-01

    Some observational studies have identified elevated uric acid concentration as a risk factor for diabetes, while others have found an inverse relationship. We examined both the association of uric acid level with incident diabetes and the change in uric acid concentration after a diabetes diagnosis. We analyzed data from the Atherosclerosis Risk in Communities (ARIC) Study and quantified the independent association between uric acid level and incident diabetes via Cox proportional hazards models. The association between duration of diabetes and change in uric acid level was examined via linear regression. Among 11,134 participants without diagnosed diabetes at baseline (1987–1989), there were 1,294 incident cases of diabetes during a median of 9 years of follow-up (1987–1998). Uric acid level was associated with diabetes even after adjustment for risk factors (per 1 mg/dL, hazard ratio = 1.18, 95% confidence interval: 1.13, 1.23), and the association remained significant after adjustment for fasting glucose and insulin levels. Among participants with diabetes (n = 1,510), every additional 5 years’ duration of diabetes was associated with a 0.10-mg/dL (95% confidence interval: 0.04, 0.15) lower uric acid level after adjustment. We conclude that uric acid concentration rises prior to diagnosis of diabetes and then declines with diabetes duration. Future studies investigating uric acid as a risk factor for cardiovascular disease should adequately account for the impact and timing of diabetes development. PMID:24418684

  5. Selective oxidation of glycerol to formic acid in highly concentrated aqueous solutions with molecular oxygen using V-substituted phosphomolybdic acids

    KAUST Repository

    Zhang, Jizhe

    2014-01-01

    Formic acid is an important commodity chemical as well as a promising medium for hydrogen storage and hydrogen production. In this paper, we report that formic acid can be produced through selective oxidation of glycerol, a low-cost by-product of biodiesel, by using vanadium-substituted phosphomolybdic acids as catalysts and molecular oxygen as the oxidant. Significantly, this catalytic system allows for high-concentration conversions and thus leads to exceptional efficiency. Specifically, 3.64 g of formic acid was produced from 10 g of glycerol/water (50/50 in weight) solution. © 2014 the Partner Organisations.

  6. Resin-Powder Dispenser

    Science.gov (United States)

    Standfield, Clarence E.

    1994-01-01

    Resin-powder dispenser used at NASA's Langley Research Center for processing of composite-material prepregs. Dispenser evenly distributes powder (resin polymer and other matrix materials in powder form) onto wet uncured prepregs. Provides versatility in distribution of solid resin in prepreg operation. Used wherever there is requirement for even, continuous distribution of small amount of powder.

  7. Effects of various antipsychotic drugs upon the striatal concentrations of para-hydroxyphenylacetic acid and meta-hydroxyphenylacetic acid in the mouse.

    OpenAIRE

    Juorio, A. V.; McQuade, P. S.

    1983-01-01

    The endogenous concentrations of p- and m-hydroxyphenylacetic acid in the mouse caudate nucleus were determined by a gas chromatographic or a gas chromatographic-mass spectrometric technique and the concentrations were about 30 and 11 ng g-1 respectively. The subcutaneous administration of (+)-butaclamol (1 mg kg-1), haloperidol (5 mg kg-1), molindone (100 mg kg-1), sulpiride (50 mg kg-1) or chlorpromazine (20 mg kg-1) increased the concentration of mouse striatal p- and m-hydroxyphenylacetic...

  8. Serum uric acid concentration and metabolic syndrome among elderly Koreans: The Korean Urban Rural Elderly (KURE) study.

    Science.gov (United States)

    Choi, Hansol; Kim, Hyeon Chang; Song, Bo Mi; Park, Ji Hye; Lee, Ju-Mi; Yoon, Da-Lim; Yoon, Young Mi; Rhee, Yumie; Youm, Yousik; Kim, Chang Oh

    2016-01-01

    Epidemiologic studies have demonstrated that elevated serum uric acid concentration is an independent risk factor for metabolic syndrome. However, few studies have focused on elderly populations. Thus, we investigated the association of serum uric acid concentration with metabolic syndrome in community-dwelling elderly Koreans. This cross-sectional analysis included 2940 participants (986 men and 1954 women) aged 65 years or older who participated in a baseline health assessment for the Korean Urban Rural Elderly cohort study from 2012 to 2014. Serum uric acid concentration was analyzed using both continuous and dichotomous variables. Hyperuricemia was defined as a uric acid concentration ≥7.0 mg/dL in men and ≥6.0 mg/dL in women. Metabolic syndrome was defined according to the 2009 harmonizing definition. Multiple logistic regression models were used to investigate independent association between serum uric acid and metabolic syndrome, after adjusting for age, body mass index, LDL cholesterol, glycated hemoglobin, blood urea nitrogen, estimated glomerular filtration rate health behaviors, and medications. Prevalence of metabolic syndrome and its components increased significantly according to uric acid concentration in both sexes. The adjusted odds ratios for having metabolic syndrome per 1.0mg/dL higher uric acid concentration were 1.16 (95% CI: 1.03-1.31) in men and 1.27 (95% CI: 1.13-1.42) in women. Hyperuricemia was also associated with metabolic syndrome, with adjusted odds ratios of 1.71 (95% CI: 1.11-2.63) in men and 1.55 (95% CI: 1.05-2.29) in women. Elevated serum uric acid concentration was independently associated with an increased prevalence of metabolic syndrome in community-dwelling elderly Koreans. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  9. Influence of ethylenediamine-n,n’-disuccinic acid (EDDS) concentration on the bactericidal activity of fatty acids in vitro

    Science.gov (United States)

    The antibacterial activity of mixtures of ethylenediamine-N,N’-disuccinic acid (EDDS) and antibacterial fatty acids (FA) was examined using the agar diffusion assay. Solutions of caproic, caprylic, capric, and lauric acids dissolved in potassium hydroxide (KOH) were supplemented with 0, 5, or 10 mM ...

  10. Complex formation of trivalent americium with salicylic acid at very low concentrations

    International Nuclear Information System (INIS)

    Melanie Mueller; Margret Acker; Steffen Taut; Gert Bernhard; Forschungszentrum Dresden-Rossendorf, Dresden

    2010-01-01

    For the first time, the complexation of americium(III) with salicylic acid was studied at trace metal concentrations using a 2.0 m Long Path Flow Cell for UV-vis spectroscopy. The detection limit of Am(III) in aqueous solution at pH 3.0 was found to be 5 x 10 -9 M. Two Am(III)-salicylate complexes were formed at pH 5.0 in 0.1 M NaClO 4 , indicated by a clear red shift of the absorption maximum. The absorption spectra obtained from spectrophotometric titration were analyzed by means of factor analysis and complex stabilities were calculated to be log β 110 = 2.56 ± 0.08 and log β 120 = 3.93 ± 0.19. (author)

  11. Increased concentration of vasopressin in plasma of essential fatty acid-deficient rats

    DEFF Research Database (Denmark)

    Hansen, Harald S.; Jensen, B.; Warberg, J.

    1985-01-01

    The effect of essential fatty acid deficiency (EFA-D) on the plasma concentration of arginine-vasopressin (AVP) and the urinary AVP excretion was investigated. Weanling rats were fed a fat-free diet (FF-rats). Control rats received the same diet in which 6% by wt. of sucrose was replaced by arachis...... oil. After 4-6 weeks of feeding, urine and plasma were analysed for AVP, osmolality, sodium and potassium. When compared to control rats FF-rats had decreased urine volume (6.0 ± 1.6 ml/24 hr versus 11.7 ± 3.2 ml/24 hr), increased urine osmolality (2409 ± 691 mOsm/kg versus 1260 ± 434 m...

  12. Effect of Phosphoric Acid Concentration on the Optical Properties of Partially Phosphorylated PVA Complexes

    Directory of Open Access Journals (Sweden)

    Asmalina Mohamed Saat

    2014-01-01

    Full Text Available Partially phosphorylated polyvinyl alcohol (PPVA films were prepared at five mole ratios of phosphoric acid (PA using solution casting technique. The optical properties of the PPVA films were examined using UV-visible (UV and photoluminescence (PL spectroscopy. The UV absorption spectra reveal that the absorption peaks are blue-shifted with an increase in PA concentration added to the pure PVA. The PL spectra show the presence of peaks which are characteristic of isotactic (389–398, 460–462 nm, syndiotactic (418–420 nm, and atactic (440–446 nm configurations of the PPVA. The results also show the peak of O–P–O bonding at a wavelength range of 481–489 nm.

  13. Study on the concentration of unsaturated fatty acid methyl esters by urea complexation

    International Nuclear Information System (INIS)

    Jiang, B.; Liu, Y.

    2014-01-01

    This study was done to obtain concentrated unsaturated fatty acid methyl esters (FAME) by urea complexation from soybean derived FAME. Effects of urea-to-FAME ratio, 95% ethanol-to-FAME ratio, crystallization temperature and time on the purification of unsaturated FAME were investigated through single factor experiments. Optimum conditions to obtain maximum FAME yield of NUCF with the purity of unsaturated FAME greater than 98% were established using Box-Behnken design (BBD) method and response surface methodology (RSM). Under optimal conditions, the FAME yield was 58.08%, and the purity of unsaturated FAME was 98% at a urea-to-FAME ratio of 1.23, 95% ethanol-to-FAME ratio of 7 and crystallization temperature of 0 degree C. Verification results revealed that the predicted values were reasonably close to experimentally observed values of 56.93% and 98.01%. (author)

  14. Anion-exchange resin-based desulfurization process. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sheth, A C; Dharmapurikar, R; Strevel, S D

    1994-01-01

    The following investigations were performed: (1) batch mode screening of eleven(11) commercially available resins and selection of three candidate resins for further evaluation in a fixed-bed setup. (2) Process variables study using three candidate resins in the fixed-bed setup and selection of the ``best`` resin for process economics development. (3) Exhaustion efficiency and solution concentration were found to be inversely related necessitating a trade-off between the resin cost versus the cost of evaporation/concentration of ensuing effluents. (4) Higher concentration of the HCO{sub 3}{sup {minus}} form of active sites over less active CO{sub 3}{sup 2{minus}} form of sites in the resin was believed to be the main reason for the observed increase in the equilibrium capacity of the resin at an elevated static CO{sub 2}-pressure. This Increase in capacity was found to level off around 80--120 psig range. The increase in CO{sub 2}-pressure, however, did not appear to affect the overall ion-exchange kinetics. (5) In the fixed-bed mode, the solution concentration was found to affect the equilibrium capacity of candidate resins. Their relationship was well satisfied by the Langmuir type non-linear equilibrium isotherm. Alternatively, the effect of solution concentration on overall ion-exchange kinetics varied from resin to resin. (6) Product inhibition effect on the resin was observed as an initial increase followed by a significant decrease in the resin`s equilibrium capacity for SO{sub 4}{sup 2{minus}} as the HCO{sub 3}{sup {minus}}/SO{sub 4}{sup 2{minus}} molar ratio in the solution was increased from 0 to 1.0. This ratio, however, did not affect the overall ion-exchange kinetics.

  15. Post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin

    International Nuclear Information System (INIS)

    Yap, A.U.J.

    1997-01-01

    This study examined the post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin using a digital microhardness tester. Change in hardness of these materials over a period of 6 months was compared to that of conventional glass ionomer cements and a composite resin. With the exception of the composite resin, all materials showed a significant increase in hardness over 24 h after their initial set. Dual-cure resin-modified glass ionomer cements showed decreased hardness with increased storage time in saline at 37 o C. Results suggest that the addition of resins to glass ionomer cements does not improve initial hardness and does not negate the acid-base reaction of conventional cements. Resin addition may, however, lead to increased water sorption and decreased hardness. (author)

  16. Effect of N deposition on tree amino acid concentrations in two Sphagnum species

    Energy Technology Data Exchange (ETDEWEB)

    Karsisto, M.; Kitunen, V. [Finnish Forest Research Inst., Vantaa (Finland). Vantaa Research Centre; Jauhiainen, J. [Joensuu Univ. (Finland). Dept. of Biology; Vasander, H. [Helsinki Univ. (Finland). Dept. of Forest Ecology

    1996-12-31

    Nitrogen saturation of ecosystems occurs when the availability of nitrogen is not a growth limiting factor. This situation can be reached through fertilisation or by nitrogen deposition. Prolonged nitrogen saturation may overload the ecosystem and cause changes in the vigour and eventually in the composition of plant communities. But before this stage is reached, certain changes in nitrogen metabolism occur. These changes can be used as an early warning of nitrogen overload to ecosystems. A change in the amino acid pool of plants has been used as an indication of various kind of stress, including, temperature, nutrient imbalance, shading, drought or excess water. It has been postulated that such stresses have an effect on protein synthesis but not on the nitrogen uptake of plants. The result is an increase in the concentration of NH{sub 4}{sup +} ions in plant cells, which may have toxic effects to the plant and the processes that assimilate the free NH{sub 4}{sup +} ions. One of such process is the synthesis of amino acids, especially those containing a significant proportion of nitrogen, e.g. arginine, glutamine and asparagine. This study about the quantification of amino acids in two species of Sphagnum mosses is part of a larger study, the aim of which is to clarify how a number of Sphagnum species will cope with climatic change and nitrogen deposition. Sphagna are the most important members of the peat forming communities in the boreal zone. Sphagnum communities are formed by species specialised to grow in conditions of low nutrient availability, mainly provided via deposition. The present structure and composition of mire communities may be endangered due to elevated levels of nitrogen deposition that have persisted over the last few decades. (20 refs.)

  17. Catalyst evaluation for oxygen reduction reaction in concentrated phosphoric acid at elevated temperatures

    Science.gov (United States)

    Hu, Yang; Jiang, Yiliang; Jensen, Jens Oluf; Cleemann, Lars N.; Li, Qingfeng

    2018-01-01

    Phosphoric acid is the common electrolyte for high-temperature polymer electrolyte fuel cells (HT-PEMFCs) that have advantages such as enhanced CO tolerance and simplified heat and water management. The currently used rotating disk electrode technique is limited to tests in dilute solutions at low temperatures and hence is not suitable for catalyst evaluation for HT-PEMFCs. In this study, we have designed and constructed a half-cell setup to measure the intrinsic activities of catalysts towards the oxygen reduction reaction (ORR) in conditions close to HT-PEMFC cathodes. By optimization of the hydrophobic characteristics of electrodes and the catalyst layer thickness, ORR activities of typical Pt/C catalysts are successfully measured in concentrated phosphoric acid at temperatures above 100 °C. In terms of mass-specific activities, the catalyst exhibits about two times higher activity in the half-cell electrode than that observed in fuel cells, indicating the feasibility of the technique as well as the potential for further improvement of fuel cell electrode performance.

  18. A simple procedure for preparing chitin oligomers through acetone precipitation after hydrolysis in concentrated hydrochloric acid.

    Science.gov (United States)

    Kazami, Nao; Sakaguchi, Masayoshi; Mizutani, Daisuke; Masuda, Tatsuhiko; Wakita, Satoshi; Oyama, Fumitaka; Kawakita, Masao; Sugahara, Yasusato

    2015-11-05

    Chitin oligomers are of interest because of their numerous biologically relevant properties. To prepare chitin oligomers containing 4-6 GlcNAc units [(GlcNAc)4-6], α- and β-chitin were hydrolyzed with concentrated hydrochloric acid at 40 °C. The reactant was mixed with acetone to recover the acetone-insoluble material, and (GlcNAc)4-6 was efficiently recovered after subsequent water extraction. Composition analysis using gel permeation chromatography and MALDI-TOF mass spectrometry indicated that (GlcNAc)4-6 could be isolated from the acetone-insoluble material with recoveries of approximately 17% and 21% from the starting α-chitin and β-chitin, respectively. The acetone precipitation method is highly useful for recovering chitin oligomers from the acid hydrolysate of chitin. The changes in the molecular size and higher-order structure of chitin during the course of hydrolysis were also analyzed, and a model that explains the process of oligomer accumulation is proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

  19. Highly improved synthesis of gold nanobipyramids by tuning the concentration of hydrochloric acid

    Energy Technology Data Exchange (ETDEWEB)

    Qi, Ying; Zhu, Jian; Li, Jianjun; Zhao, Junwu, E-mail: nanoptzhao@163.com [Xi’an Jiaotong University, The Key Laboratory of Biomedical Information Engineering of Ministry of Education, School of Life Science and Technology (China)

    2016-07-15

    Fabrication of gold nanobipyramids (Au BPs) has attracted great attention because they exhibit more advantageous plasmonic properties. In this study, Au BPs were synthesized by the well-known seeded growth in the presence of hydrochloric acid (HCl). The effects of the ingredients, including HCl, silver nitrate (AgNO{sub 3}), l-Ascorbic acid (AA), and seeds on the structure and yield of the Au BPs were systemically investigated. The results showed that the abundant HCl could improve the yield of Au BPs and decrease the longitudinal surface plasmon resonance wavelength. Under the circumstance of higher concentration of AA and AgNO{sub 3}, more byproducts were resulted. In addition, the effect of HCl under different ratios of seed solution to AA has also been studied. The results showed that the yield was less sensitive to HCl when the amount of seed solution was small. If substantial AA was added to the system, then abundant HCl should be introduced correspondingly to improve the yield of Au BPs.

  20. Effect of L (+) ascorbic acid and monosodium glutamate concentration on the morphology of calcium carbonate

    Science.gov (United States)

    Saraya, Mohamed El-shahte Ismaiel

    2015-11-01

    In this study, monosodium glutamate and ascorbic acid were used as crystal and growth modifiers to control the crystallization of CaCO3. Calcium carbonate prepared by reacting a mixed solution of Na2CO3 with CaCl2 at ambient temperature, (25 °C), constant Ca++/ CO3- - molar ratio and pH with stirring. The polymorph and morphology of the crystals were characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The results indicate that rhombohedral calcite was only formed in water without organic additives, and both calcite and spherical vaterite with various morphologies were produced in the presence of monosodium glutamate. The content of vaterite increased as the monosodium glutamate increased. In addition, spherical vaterite was obtained in the presence of different concentrations of ascorbic acid. The spherical vaterite posses an aggregate shape composed of nano-particles, ranging from 30 to 50 nm as demonstrated by the SEM and TEM analyses. Therefore, the ascorbic stabilizes vaterite and result in nano-particles compared to monosodium glutamate.

  1. Effect of salicylic acid on Concentration of nutrients, protein and antioxidant enzymes of basil under lead stress

    Directory of Open Access Journals (Sweden)

    Ali Padash

    2016-03-01

    Full Text Available Today, phenolic compounds and plant growth regulator has been proposed, to reduce the negative effects of stress. Salicylic acid is a substance that causes plant resistance to biotic and abiotic stresses. This experiment was conducted in Zabol University during 2013 as factorial randomized complete block design with 3 replications. Factors included 4 levels of lead nitrate; 0 (control, 100, 200 and 300 mg per kg of soil and foliar application of salicylic acid at 3 levels of 0, 50 and 100 ppm. Addition of lead significantly reduced concentrations of potassium, magnesium, calcium, phosphorous and nitrogen and increased concentrations of sodium, polyphenol oxidase, ascorbate peroxidase, superoxide dismutase and peroxidase. In addition, salicylic acid spraying had a significant influence on all traits, and salicylic acid spraying at 100 mL/L increased concentrations of potassium, magnesium, calcium, phosphorus, nitrogen and decreased concentrations of polyphenol oxidase, ascorbate peroxidase, superoxide dismutase and peroxidase. In this study the interaction between salicylic acid and lead on potassium, magnesium, calcium, phosphorus, nitrogen, sodium and catalase, guaiacol peroxidase and polyphenol oxidase were significant, and salicylic acid play moderating role and reducing the negative effects of lead toxicity. The results suggested salicylic acid application in basil can increase uptake of macro and micro nutrients required for plant growth and reduce the negative effects of stress lead-induced oxidative damage.

  2. Seasonal variations in the concentrations of lipophilic compounds and phenolic acids in the roots of Echinacea purpurea and Echinacea pallida.

    Science.gov (United States)

    Thomsen, Maria O; Fretté, Xavier C; Christensen, Kathrine B; Christensen, Lars P; Grevsen, Kai

    2012-12-12

    Roots of Echinacea purpurea and Echinacea pallida cultivated for 4 years in a North European climate were analyzed for seasonal variations in the concentrations of lipophilic constituents (alkamides, ketoalkenes, and ketoalkynes) and phenolic acids by harvesting five times during 1 year to establish the optimal time for harvest. A total of 16 alkamides, three ketoalkenes, two ketoalkynes, and four phenolic acids (echinacoside, cichoric acid, caftaric acid, and chlorogenic acid) were identified in aqueous ethanolic (70%) extracts by liquid chromatography-mass spectrometry and quantified by reverse-phase high-performance liquid chromatography. The major alkamides in the roots of E. purpurea were at their lowest concentration in the middle of autumn and early winter, and the total concentration of lipophilic compounds in E. pallida showed the same pattern. Moreover, all of the major phenolic acids in E. purpurea were at their highest concentrations in spring. The optimal harvest time in spring is in contrast to normal growing guidelines; hence, this specific information of seasonal variations in the concentrations of lipophilic and phenolic compounds in E. purpurea and E. pallida is valuable for research, farmers, and producers of medicinal preparations.

  3. Ontario Hydro Research Division's program for treatment of spent ion-exchange resins

    International Nuclear Information System (INIS)

    Nott, B.R.; Dodd, D.J.R.

    1981-09-01

    A brief review of the evolution of work programmes for chemical treatment of spent ion-exchange resins in Ontario Hydro's Research Division is presented. Attention has been focussed on pre-treatment processes for the treatment of the spent resins prior to encapsulation of the products in solid matrices. Spent Resin Regeneration and Acid Stripping processes were considered in some detail. Particular attention was paid to carbon-14 on spent resins, its determination in and removal from the spent resins (with the acid stripping technique). The use of separate cation and anion resin beds instead of mixed bed resins was examined with a view to reducing the volume of resin usage and consequently the volume of waste radioactive ion-exchange resin generated. (author)

  4. Corn stover saccharification with concentrated sulfuric acid: effects of saccharification conditions on sugar recovery and by-product generation.

    Science.gov (United States)

    Liu, Ze-Shen; Wu, Xiao-Lei; Kida, Kenji; Tang, Yue-Qin

    2012-09-01

    Although concentrated sulfuric acid saccharification is not a novel method for breaking down lignocellulosic biomass, the process by which saccharification affects biomass decomposition, sugar recovery, and by-product generation is not well studied. The present study employed Taguchi experimental design to study the effects of seven parameters on corn stover concentrated sulfuric acid saccharification. The concentration of sulfuric acid and the temperature of solubilization significantly affect corn stover decomposition. They also have significant effects on glucose and xylose recoveries. Low generation of furfural and 5-hydroxymethyl-2-furfural (5HMF) was noted and organic acids were the main by-products detected in the hydrolysate. Temperature also significantly affected the generation of levulinic acid and formic acid; however, acetic acid generation was not significantly influenced by all seven parameters. The ratio of acid to feedstock significantly affected glucose recovery, but not total sugar recovery. The corn stover hydrolysate was well fermented by both glucose- and xylose-fermenting yeast strains. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. Concentration and entry rate of amino acids in buffalo calves fed on two planes of crude protein

    International Nuclear Information System (INIS)

    Verma, D.N.; Singh, U.B.; Varma, A.; Ranjhan, S.K.

    1974-01-01

    Amino acid entry rates into the body pool have been estimated in buffalo calves using a single injection isotope dilution technique. The animals received 2 levels of crude protein, 13 percent lower and 19 percent higher than NRC recommendation. The concentrations of free amino acid in plasma were 5.49 and 7.17 mg/100 ml in animals fed on low and high crude protein diet, respectively. There was significant differences in the plasma amino acid concentration and entry rates between the groups. Amino acid entry rates were 79.17 and 117.78 mg per min in groups fed on low and high plane of crude protein respectively, showing that availability of amino acid is better in animals given ratio high in crude protein contents. (author)

  6. Determination of Optimum Duration and Concentration of Stevia (Stevia rebaudiana Bert.) Seed Priming with Boric Acid (H3BO3)

    OpenAIRE

    SHAHVERDI, Mehdi Aghighi; OMIDI, Heshmat; TABATABAEI, Seyed Jalal

    2017-01-01

    In order to determine optimal duration and concentration of Stevia seed priming with boric acid for improving germination, an experimental factorial completely randomized design with three replications was conducted in the laboratory of Seed Science and Technology, Shahed University of Tehran in 2015. The first factor was different concentrations of boric acid (0, 0.5, 1.0, 1.5 and 2.0 percent) and the second factor was priming duration (0, 8, 16, 24 and 32 hours). Effects of concentration an...

  7. Volatile fatty acids production in the rumen of young heifers given diets containing a l