Bacillus cereus as indicator in the sterilization of residual water with high energy electrons

International Nuclear Information System (INIS)

Mejia Z, E.

2000-01-01

One of the main causes of water pollution is the presence of microorganisms that provoke infections, moreover of chemical substances. The processes of residual water treatment finally require of the disinfection for its use or final disposition. The radiation technology for the residual water treatment by mean of electron beams is an innovator process because as well as decomposing the chemical substance or to degrade them, also it provokes a disinfection by which this is proposed as alternative for disinfection of residual water, with the purpose in reusing the water treated in the agriculture, recreation and industry among others secondary activities, solving environmental or health problems. The objective of this work is to evaluate the use of Bacillus cereus as biological indicator in the disinfection by radiation, using High Energy Electrons. To fulfil with this objective, the work was developed in three stages, the first one consisted in the acquisition, propagation and conservation of the Bacillus cereus stumps, considering Escherichia coli and Salmonella typhimurium as pathogenic germs present in residual water. Moreover, the inocule standardization and the conditions of the Electron accelerator Type Pelletron. In the second stage it was performed the irradiation of aqueous samples of the microorganisms simulating biological pollution and the application to problem samples of a treatment plant sited in the Lerma River zone of mixed residual water. And in the third stage was performed a regression analysis to the reported survival for each kind of microorganisms. The results obtained show that with the use of Electron beams was reduced 6 logarithmic units de E. coli at 129 Gy, for S. typhimurium it was reduced 8 logarithmic units at 383 Gy and the B. cereus at 511 Gy was reduced 6.8 logarithmic units. Of the problem samples irradiated at 500 Gy, the concentration of the total account diminished from 8.70 x 10 7 UFC/ml to 550 UFC/ml, the presence of B. Cereus

Distribution of pesticide residues in soil and uncertainty of sampling.

Science.gov (United States)

Suszter, Gabriela K; Ambrus, Árpád

2017-08-03

Pesticide residues were determined in about 120 soil cores taken randomly from the top 15 cm layer of two sunflower fields about 30 days after preemergence herbicide treatments. Samples were extracted with acetone-ethyl acetate mixture and the residues were determined with GC-TSD. Residues of dimethenamid, pendimethalin, and prometryn ranged from 0.005 to 2.97 mg/kg. Their relative standard deviations (CV) were between 0.66 and 1.13. The relative frequency distributions of residues in soil cores were very similar to those observed in root and tuber vegetables grown in pesticide treated soils. Based on all available information, a typical CV of 1.00 was estimated for pesticide residues in primary soil samples (soil cores). The corresponding expectable relative uncertainty of sampling is 20% when composite samples of size 25 are taken. To obtain a reliable estimate of the average residues in the top 15 cm layer of soil of a field up to 8 independent replicate random samples should be taken. To obtain better estimate of the actual residue level of the sampled filed would be marginal if larger number of samples were taken.

Removal of six pesticide residues in cowpea with alkaline electrolysed water.

Science.gov (United States)

Han, Yongtao; Song, Le; An, Quanshun; Pan, Canping

2017-06-01

Reduction of six pesticide residues (isoprocarb, chlorpyrifos, bifenthrin, beta-cypermethrin, difenoconazole and azoxystrobin) in cowpea by alkaline electrolysed water (AlEW) solutions with different pH was investigated. The commonly used washing treatments in household processing were used for comparison. The residue magnitudes were determined by gas chromatography coupled with tandem mass spectrometry (GC-MS/MS). Results showed that the removal effect of AlEW solution on the six pesticides was superior to tap water, 5% sodium chloride, 5% sodium carbonate and 5% acetic acid solution. AlEW with pH 12.2 had more potential to eliminate the six pesticides in cowpeas. Moreover, the reduction of pesticide residues gradually increased with the increase of washing time. This study demonstrated that AlEW solution with pH of 12.2 could be used to reduce pesticide residues on fresh cowpea samples. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Enhanced Cleaning of Genesis Solar Wind Sample 61348 for Film Residue Removal

Science.gov (United States)

Allums, K. K.; Gonzalez, C. P.; Kuhlman, K. R.; Allton, J. H.

2015-01-01

The Genesis mission returned to Earth on September 8, 2004, experiencing a nonnominal reentry. During the recovery of the collector materials from the capsule, many of the collector fragments were placed on the adhesive protion of post-it notes to prevent the fragments from moving during transport back to Johnson Space Center. This unknowingly provided an additional contaminate that would prove difficult to remove with the limited chemistries allowed in the Genesis Curation Laboratory. Generally when collector material samples are prepared for allocation to PIs, the samples are cleaned front side only with Ultra-Pure Water (UPW) via megasonic dispersion to the collector surface to remove crash debris and contamination. While this cleaning method works well on samples that were not placed on post-its during recovery, it has caused movement of the residue on the back of the sample to be deposited on the front in at least two examples. Therefore, samples placed on the adhesive portion on post-it note, require enhanced cleaning methods since post-it residue has proved resistant to UPW cleaning.

Residuals Management and Water Pollution Control Planning.

Science.gov (United States)

Environmental Protection Agency, Washington, DC. Office of Public Affairs.

This pamphlet addresses the problems associated with residuals and water quality especially as it relates to the National Water Pollution Control Program. The types of residuals and appropriate management systems are discussed. Additionally, one section is devoted to the role of citizen participation in developing management programs. (CS)

Residual water treatment for gamma radiation. Tratamiento de aguas residuales por radiacion gamma

Energy Technology Data Exchange (ETDEWEB)

Mendez, L [Universidad Nacional Mayor de San Marcos. Facultad de Quimica (Peru)

1990-07-01

The treatment of residual water by means of gamma radiation for its use in agricultural irrigation is evaluated. Measurements of physical, chemical, biological and microbiological contamination indicators were performed. For that, samples from the treatment center of residual water of San Juan de Miraflores were irradiated up to a 52.5 kGy dose. The study concludes that gamma radiation is effective to remove parasites and bacteria, but not for removal of the organic and inorganic matter. (author). 15 refs., 3 tabs., 4 figs.

Pre-concentration of pesticide residues in environmental water samples using Silica nanoparticles and identification of residues By GC-MS method

OpenAIRE

Tentu. Nageswara Rao; A. Muralidhar Reddy; SNVS. Murthy; Prathipati Revathi; K. Suneel Kumar

2016-01-01

The silica nanoparticles prepared by stober’s mechanism by reaction of tetraethylorthosilicate (TEOS) with ammonia was tested for their adsorption capacity in the pre-concentration of residues of pesticides in water. The synthesized nanoparticles were characterized by Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) and X-Ray Diffraction (XRD). The size of the silica nanoparticles were 50 to 250 nm. The solid phase extraction (SPE) cartridges were prepared by filling...

Water dynamics clue to key residues in protein folding

International Nuclear Information System (INIS)

Gao, Meng; Zhu, Huaiqiu; Yao, Xin-Qiu; She, Zhen-Su

2010-01-01

A computational method independent of experimental protein structure information is proposed to recognize key residues in protein folding, from the study of hydration water dynamics. Based on all-atom molecular dynamics simulation, two key residues are recognized with distinct water dynamical behavior in a folding process of the Trp-cage protein. The identified key residues are shown to play an essential role in both 3D structure and hydrophobic-induced collapse. With observations on hydration water dynamics around key residues, a dynamical pathway of folding can be interpreted.

Neonicotinoid insecticide residues in surface water and soil associated with commercial maize (corn fields in southwestern Ontario.

Directory of Open Access Journals (Sweden)

Arthur Schaafsma

Full Text Available Neonicotinoid insecticides have come under scrutiny for their potential unintended effects on non-target organisms, particularly pollinators in agro-ecosystems. As part of a larger study of neonicotinoid residues associated with maize (corn production, 76 water samples within or around the perimeter of 18 commercial maize fields and neighbouring apiaries were collected in 5 maize-producing counties of southwestern Ontario. Residues of clothianidin (mean = 2.28, max. = 43.60 ng/mL and thiamethoxam (mean = 1.12, max. = 16.50 ng/mL were detected in 100 and 98.7% of the water samples tested, respectively. The concentration of total neonicotinoid residues in water within maize fields increased six-fold during the first five weeks after planting, and returned to pre-plant levels seven weeks after planting. However, concentrations in water sampled from outside the fields were similar throughout the sampling period. Soil samples from the top 5 cm of the soil profile were also collected in these fields before and immediately following planting. The mean total neonicotinoid residue was 4.02 (range 0.07 to 20.30 ng/g, for samples taken before planting, and 9.94 (range 0.53 to 38.98 ng/g, for those taken immediately after planting. Two soil samples collected from within an conservation area contained detectable (0.03 and 0.11 ng/g concentrations of clothianidin. Of three drifted snow samples taken, the drift stratum containing the most wind-scoured soil had 0.16 and 0.20 ng/mL mainly clothianidin in the melted snow. The concentration was at the limit of detection (0.02 ng/mL taken across the entire vertical profile. With the exception of one sample, water samples tested had concentrations below those reported to have acute, chronic or sublethal effects to honey bees. Our results suggest that neonicotinoids may move off-target by wind erosion of contaminated soil. These results are informative to risk assessment models for other non-target species in maize

Neonicotinoid Insecticide Residues in Surface Water and Soil Associated with Commercial Maize (Corn) Fields in Southwestern Ontario

Science.gov (United States)

Schaafsma, Arthur; Limay-Rios, Victor; Baute, Tracey; Smith, Jocelyn; Xue, Yingen

2015-01-01

Neonicotinoid insecticides have come under scrutiny for their potential unintended effects on non-target organisms, particularly pollinators in agro-ecosystems. As part of a larger study of neonicotinoid residues associated with maize (corn) production, 76 water samples within or around the perimeter of 18 commercial maize fields and neighbouring apiaries were collected in 5 maize-producing counties of southwestern Ontario. Residues of clothianidin (mean = 2.28, max. = 43.60 ng/mL) and thiamethoxam (mean = 1.12, max. = 16.50 ng/mL) were detected in 100 and 98.7% of the water samples tested, respectively. The concentration of total neonicotinoid residues in water within maize fields increased six-fold during the first five weeks after planting, and returned to pre-plant levels seven weeks after planting. However, concentrations in water sampled from outside the fields were similar throughout the sampling period. Soil samples from the top 5 cm of the soil profile were also collected in these fields before and immediately following planting. The mean total neonicotinoid residue was 4.02 (range 0.07 to 20.30) ng/g, for samples taken before planting, and 9.94 (range 0.53 to 38.98) ng/g, for those taken immediately after planting. Two soil samples collected from within an conservation area contained detectable (0.03 and 0.11 ng/g) concentrations of clothianidin. Of three drifted snow samples taken, the drift stratum containing the most wind-scoured soil had 0.16 and 0.20 ng/mL mainly clothianidin in the melted snow. The concentration was at the limit of detection (0.02 ng/mL) taken across the entire vertical profile. With the exception of one sample, water samples tested had concentrations below those reported to have acute, chronic or sublethal effects to honey bees. Our results suggest that neonicotinoids may move off-target by wind erosion of contaminated soil. These results are informative to risk assessment models for other non-target species in maize agro

Analysis of residual chlorine in simple drinking water distribution system with intermittent water supply

Science.gov (United States)

Goyal, Roopali V.; Patel, H. M.

2015-09-01

Knowledge of residual chlorine concentration at various locations in drinking water distribution system is essential final check to the quality of water supplied to the consumers. This paper presents a methodology to find out the residual chlorine concentration at various locations in simple branch network by integrating the hydraulic and water quality model using first-order chlorine decay equation with booster chlorination nodes for intermittent water supply. The explicit equations are developed to compute the residual chlorine in network with a long distribution pipe line at critical nodes. These equations are applicable to Indian conditions where intermittent water supply is the most common system of water supply. It is observed that in intermittent water supply, the residual chlorine at farthest node is sensitive to water supply hours and travelling time of chlorine. Thus, the travelling time of chlorine can be considered to justify the requirement of booster chlorination for intermittent water supply.

Effect of residual water content on the physico-chemical properties of sucralfate dried gel obtained by microwave drying.

Science.gov (United States)

Gainotti, Alessandro; Losi, Elena; Bettini, Ruggero; Colombo, Paolo; Sonvico, Fabio; Baroni, Daniela; Santi, Patrizia; Colombo, Gaia

2005-08-01

The purpose of this study was to investigate the physico-chemical characteristics of sucralfate humid gel dried by microwaves, in relation to the residual water content. Differential scanning calorimetry (DSC) allowed for the determination of the water state in sucralfate samples. Fourier-transform infrared (FT-IR) spectroscopy was used to monitor the changes in sucralfate gel structure induced by the microwave drying. A boundary value of total water content for sucralfate gel samples was found at 42% (w/w). Below this value only bound water was present, whereas above this value, the increase in total water was due to free water. In the physical form of gel, the strength of the coordination between sulfate anions and the positively charged aluminum hydroxide was dependent on the residual water content. The study of the sedimentation behavior of water suspensions prepared with dried sucralfate allowed for the evaluation of the retention of gel properties. We found that the microwave drying process affected the sedimentation of sucralfate dried gel suspensions independent of the residual water content: when suspensions were prepared from sucralfate dried gel powders containing more than 42% (w/w) of residual water, the sedimentation ratio was higher than 0.9. The non-gel powder suspension showed a sedimentation ratio of 0.68 +/- 0.02, whereas the sucralfate humid gel suspension did not sediment.

Soil water evaporation and crop residues

Science.gov (United States)

Crop residues have value when left in the field and also when removed from the field and sold as a commodity. Reducing soil water evaporation (E) is one of the benefits of leaving crop residues in place. E was measured beneath a corn canopy at the soil suface with nearly full coverage by corn stover...

Anaerobia Treatments of the domestic residual waters. Limitations potentialities

International Nuclear Information System (INIS)

Giraldo Gomez, Eugenio

1993-01-01

The quick growth of the Latin American cities has prevented that an appropriate covering of public services is achieved for the whole population, One of the undesirable consequences of this situation is the indiscriminate discharge from the domestic and industrial residual waters to the nearest bodies of water with its consequent deterioration and with disastrous consequences about the ecology and the public health. The developed countries have controlled this situation using systems of purification of the residual waters previously to their discharge in the receptor source. The same as the technology of the evacuation of the served waters, they have become numerous efforts for the application of the purification systems used in the countries developed to the socioeconomic, climatic and cultural conditions of our means. One of the results obtained in these efforts is the economic inability of the municipalities to pay the high investment costs and of operation of the traditional systems for the treatment of the residual waters. Contrary to another type of public services, the treatment of the residual waters needs of appropriate technological solutions for the Climatic and socioeconomic means of the developing countries, One of the technological alternatives for the purification of the residual waters that has had a great development in the last decades has been that of the biological treatments in t anaerobia ambient. The objective of this contribution is to present, to author's trial, the limitations and potentialities of this technology type with special emphasis in the case of the domestic residual waters

Decomposition of dilute residual active chlorine in sea-water

International Nuclear Information System (INIS)

Yoshinaga, Tetsutaro; Kawano, Kentaro; Yanagase, Kenjiro; Shiga, Akira

1985-01-01

Coastal industries such as power stations require enormous quantities of sea-water for cooling, but the marine organisms in it often result in fouling and/or blockade of the circulating water condenser and pipeworks. To prevent this, chlorine, or hypochlorite by the direct electrolysis of sea-water have been added. Environmental concerns, however, dictate that the residual chlorine concentration at the outlet should be less than the regulated value (0.02 ppm). Methods for decomposing dilute residual chlorine solutions were therefore studied. It was found that: 1) The addition of (raw) sea-water to the sea-water which passed through the condenser lowered the residual chlorine concentration to an greater extent than could be expected by dilution only. 2) Ozonation of the residual chlorine solution led to degradation of OCl - , but in solutions with a residual chlorine concentrations of less than 3 -- 4 ppm, ozonation had no effect. 3) Irradiation with ultra violet light (254 nm) decomposed the residual chlorine. Under the present work conditions (25 0 C: pH 8; depth 10 mm), nearly first order kinetics were to hold [da/dt = ksub((1)) (1-a)sup(n)]. There is a proportional relationship between the kinetic constant (k) and illuminous intensity (L), i.e., ksub((1))[C 0 sup(Cl 2 ): 10 ppm] = 6.56 x 10 -5 L (L = 0 -- 1000 lx). Thus, the use of both sea-water addition and UV irradiation provides a probable method for decomposing a residual chlorine to the expected concentration. (author)

UMTRA project water sampling and analysis plan, Gunnison, Colorado

International Nuclear Information System (INIS)

1994-06-01

This water sampling and analysis plan summarizes the results of previous water sampling activities and the plan for water sampling activities for calendar year 1994. A buffer zone monitoring plan is included as an appendix. The buffer zone monitoring plan is designed to protect the public from residual contamination that entered the ground water as a result of former milling operations. Surface remedial action at the Gunnison Uranium Mill Tailings Remedial Action Project site began in 1992; completion is expected in 1995. Ground water and surface water will be sampled semiannually in 1994 at the Gunnison processing site (GUN-01) and disposal site (GUN-08). Results of previous water sampling at the Gunnison processing site indicate that ground water in the alluvium is contaminated by the former uranium processing activities. Background ground water conditions have been established in the uppermost aquifer (Tertiary gravels) at the Gunnison disposal site. The monitor well locations provide a representative distribution of sampling points to characterize ground water quality and ground water flow conditions in the vicinity of the sites. The list of analytes has been modified with time to reflect constituents that are related to uranium processing activities and the parameters needed for geochemical evaluation. Water sampling will be conducted at least semiannually during and one year following the period of construction activities, to comply with the ground water protection strategy discussed in the remedial action plan (DOE, 1992a)

The influence of the calibration standard and the chemical composition of the water samples residue in the counting efficiency of proportional detectors for gross alpha and beta counting. Application on the radiologic control of the IPEN-CNEN/SP

International Nuclear Information System (INIS)

Santos, Cecilia Martins

2003-01-01

In this work the efficiency calibration curves of thin-window and low background gas-flow proportional counters were determined for calibration standards with different energies and different absorber thicknesses. For the gross alpha counting we have used 241 Am and natural uranium standards and for the gross beta counting we have used 90 Sr/ 90 Y and 137 Cs standards in residue thicknesses ranging from 0 to approximately 18 mg/cm 2 . These sample thicknesses were increased with a previously determined salted solution prepared simulating the chemical composition of the underground water of IPEN The counting efficiency for alpha emitters ranged from 0,273 +- 0,038 for a weightless residue to only 0,015 +- 0,002 in a planchet containing 15 mg/cm 2 of residue for 241 Am standard. For natural uranium standard the efficiency ranged from 0,322 +- 0,030 for a weightless residue to 0,023 +- 0,003 in a planchet containing 14,5 mg/cm 2 of residue. The counting efficiency for beta emitters ranged from 0,430 +- 0,036 for a weightless residue to 0,247 +- 0,020 in a planchet containing 17 mg/cm 2 of residue for 137 Cs standard. For 90 Sr/ 90 Y standard the efficiency ranged from 0,489 +- 0,041 for a weightless residue to 0,323 +- 0,026 in a planchet containing 18 mg/cm 2 of residue. Results make evident the counting efficiency variation with the alpha or beta emitters energies and the thickness of the water samples residue. So, the calibration standard, the thickness and the chemical composition of the residue must always be considered in the gross alpha and beta radioactivity determination in water samples. (author)

Role of iron and aluminum coagulant metal residuals and lead release from drinking water pipe materials.

Science.gov (United States)

Knowles, Alisha D; Nguyen, Caroline K; Edwards, Marc A; Stoddart, Amina; McIlwain, Brad; Gagnon, Graham A

2015-01-01

Bench-scale experiments investigated the role of iron and aluminum residuals in lead release in a low alkalinity and high (> 0.5) chloride-to-sulfate mass ratio (CSMR) in water. Lead leaching was examined for two lead-bearing plumbing materials, including harvested lead pipe and new lead: tin solder, after exposure to water with simulated aluminum sulfate, polyaluminum chloride and ferric sulfate coagulation treatments with 1-25-μM levels of iron or aluminum residuals in the water. The release of lead from systems with harvested lead pipe was highly correlated with levels of residual aluminum or iron present in samples (R(2) = 0.66-0.88), consistent with sorption of lead onto the aluminum and iron hydroxides during stagnation. The results indicate that aluminum and iron coagulant residuals, at levels complying with recommended guidelines, can sometimes play a significant role in lead mobilization from premise plumbing.

Rapid analysis of pesticide residues in drinking water samples by dispersive solid-phase extraction based on multiwalled carbon nanotubes and pulse glow discharge ion source ion mobility spectrometry.

Science.gov (United States)

Zou, Nan; Gu, Kejia; Liu, Shaowen; Hou, Yanbing; Zhang, Jialei; Xu, Xiang; Li, Xuesheng; Pan, Canping

2016-03-01

An analytical method based on dispersive solid-phase extraction with a multiwalled carbon nanotubes sorbent coupled with positive pulse glow discharge ion mobility spectrometry was developed for analysis of 30 pesticide residues in drinking water samples. Reduced ion mobilities and the mass-mobility correlation of 30 pesticides were measured. The pesticides were divided into five groups to verify the separation capability of pulse glow discharge in mobility spectrometry. The extraction conditions such as desorption solvent, ionic strength, conditions of adsorption and desorption, the amounts of multiwalled carbon nanotubes, and solution pH were optimized. The enrichment factors of pesticides were 5.4- to 48.7-fold (theoretical enrichment factor was 50-fold). The detection limits of pesticides were 0.01∼0.77 μg/kg. The linear range was 0.005-0.2 mg/L for pesticide standard solutions, with determination coefficients from 0.9616 to 0.9999. The method was applied for the analysis of practical and spiked drinking water samples. All results were confirmed by high-performance liquid chromatography with tandem mass spectrometry. The proposed method was proven to be a commendably rapid screening qualitative and semiquantitative technique for the analysis of pesticide residues in drinking water samples on site. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Tetracycline residues in porcine stomach after administration via drinking water on a swine farm.

Science.gov (United States)

Lindquist, Danielle; Wu, Huali; Mason, Sharon; Yeatts, Jim; Brooks, Jim; Barlow, Beth; Schill, Kaitlyn; Baynes, Ronald

2014-01-01

Tetracycline is a broad-spectrum antibiotic used to treat infections in swine. The maximum residue levels of tetracycline in pork stomach tissue in Russia, Europe, and the United States are 10, 200, and 2,000 ppb, respectively. This difference in accepted safety levels may be the reason why stomach tissues that the United States exports continue to be residue violators in overseas markets. In this study, 30 pigs at two different stages of production (weanling and finisher) were treated with tetracycline at 22 mg/kg of body weight per day for a total of 5 days via a water medicator. Blood samples were collected at 0, 72, 78, 96, and 102 h after the start of medication. The medication was stopped at 120 h, and blood samples were again collected at 126, 144, 168, 192, and 216 h after exposure. Five animals were slaughtered for stomach tissue 0, 24, 48, 96, and 192 h after the drug was flushed from the water line. All blood and tissue samples were analyzed by high-performance liquid chromatography-UV methods. The tetracycline levels in plasma were below the level of detection after the U.S.-labeled withdrawal time of 4 days. The stomach tissue residues averaged 671.72, 330.31, 297.77, 136.36, and 268.08 ppb on withdrawal days 0, 1, 2, 4, and 8, respectively. Using the U.S. Food and Drug Administration tolerance limit method and a population-based pharmacokinetic model with Monte Carlo simulation, a withdrawal interval was estimated. This study demonstrated that tetracycline residues are still detectable in the stomach tissues after the established United States withdrawal time of 4 days. These residue levels may explain why stomach tissues tested in Russia and Europe show positive residues for tetracycline, even though the meat may pass inspection here in the United States prior to export.

Welding residual stress improvement in internal components by water jet peening

International Nuclear Information System (INIS)

Enomoto, K.; Hirano, K.; Hayashi, M.; Hayashi, E.

1996-01-01

Cavitations are generated when highly pressurized water is jetted in water. Surface residual stress is improved remarkably due to the peening effect of extremely high pressure caused by the collapse of cavitation bubbles. This technique is called water jet peening (WJP). WJP is expected to be an effective maintenance technique for the prevention of stress corrosion cracking caused by residual stress in various components of power generating plants. Various kinds of specimens were water jet peened to evaluate the fundamental characteristics of WJP and to select the most appropriate conditions for the residual stress improvement. Test results showed that WJP markedly improved the tensile residual stress caused by welding and grinding to the high compressive residual stress and seems to prevent the stress corrosion cracking

A method for assessing residual NAPL based on organic chemical concentrations in soil samples

International Nuclear Information System (INIS)

Feenstra, S.; Mackay, D.M.; Cherry, J.A.

1991-01-01

Ground water contamination by non-aqueous phase liquid (NAPL) chemicals is a serious concern at many industrial facilities and waste disposal sites. NAPL in the form of immobile residual contamination, or pools of mobile or potentially mobile NAPL, can represent continuing sources of ground water contamination. In order to develop rational and cost-effective plans for remediation of soil and ground water contamination at such sites, it is essential to determine if non-aqueous phase liquid (NAPL) chemicals are present in the subsurface and delineate the zones of NAPL contamination. Qualitatively, soil analyses that exhibit chemical concentrations in the percent range or >10,000 mg/kg would generally be considered to indicate the presence of NAPL. However, the results of soil analyses are seldom used in a quantitative manner to assess the possible presence of residual NAPL contamination when chemical concentrations are lower and the presence of NAPL is not obvious. The assessment of the presence of NAPL in soil samples is possible using the results of chemical and physical analyses of the soil, and the fundamental principles of chemical partitioning in unsaturated or saturated soil. The method requires information on the soil of the type typically considered in ground water contamination studies and provides a simple tool for the investigators of chemical spill and waste disposal sites to assess whether soil chemical analyses indicate the presence of residual NAPL in the subsurface

Estimation of the residual bromine concentration after disinfection of cooling water by statistical evaluation.

Science.gov (United States)

Megalopoulos, Fivos A; Ochsenkuehn-Petropoulou, Maria T

2015-01-01

A statistical model based on multiple linear regression is developed, to estimate the bromine residual that can be expected after the bromination of cooling water. Make-up water sampled from a power plant in the Greek territory was used for the creation of the various cooling water matrices under investigation. The amount of bromine fed to the circuit, as well as other important operational parameters such as concentration at the cooling tower, temperature, organic load and contact time are taken as the independent variables. It is found that the highest contribution to the model's predictive ability comes from cooling water's organic load concentration, followed by the amount of bromine fed to the circuit, the water's mean temperature, the duration of the bromination period and finally its conductivity. Comparison of the model results with the experimental data confirms its ability to predict residual bromine given specific bromination conditions.

Suitability of the line intersect method for sampling hardwood logging residues

Science.gov (United States)

A. Jeff Martin

1976-01-01

The line intersect method of sampling logging residues was tested in Appalachian hardwoods and was found to provide unbiased estimates of the volume of residue in cubic feet per acre. Thirty-two chains of sample line were established on each of sixteen 1-acre plots on cutover areas in a variety of conditions. Estimates from these samples were then compared to actual...

Modeling Residual NAPL in Water-Wet Porous Media

Directory of Open Access Journals (Sweden)

R.J. Lenhard

2002-06-01

Full Text Available A model is outlined that predicts NAPL which is held in pore wedges and as films or lenses on solid and water surfaces and contributes negligibly to NAPL advection. This is conceptually referred to as residual NAPL. Since residual NAPL is immobile, it remains in the vadose zone after all free NAPL has drained. Residual NAPL is very important because it is a long-term source for groundwater contamination. Recent laboratory experiments have demonstrated that current models for predicting subsurface NAPL behavior are inadequate because they do not correctly predict residual NAPL. The main reason for the failure is a deficiency in the current constitutive theories for multiphase flow that are used in numerical simulators. Multiphase constitutive theory governs the relations among relative permeability, saturation, and pressure for fluid systems (i.e., air, NAPL, water. In this paper, we outline a model describing relations between fluid saturations and pressures that can be combined with existing multiphase constitutive theory to predict residual NAPL. We test the revised constitutive theory by applying it to a scenario involving NAPL imbibition and drainage, as well as water imbibition and drainage. The results suggest that the revised constitutive theory is able to predict the distribution of residual NAPL in the vadose zone as a function of saturation-path history. The revised model describing relations between fluid saturation and pressures will help toward developing or improving numerical multiphase flow simulators.

UMTRA Project water sampling and analysis plan, Gunnison, Colorado. Revision 2

International Nuclear Information System (INIS)

1995-09-01

Surface remedial action at the Gunnison Uranium Mill Tailings Remedial Action Project site began in 1992; completion is expected in 1995. Ground water and surface water will be sampled semiannually at the Gunnison processing site (GUN-01) and disposal site (GUN-08). Results of previous water sampling at the Gunnison processing site indicate that ground water in the alluvium is contaminated by the former uranium processing activities. Background ground water conditions have been established in the uppermost aquifer (Tertiary gravels) at the Gunnison disposal site. Semiannual water sampling is scheduled for the spring and fall. Water quality sampling is conducted at the processing site (1) to ensure protection of human health and the environment, (2) for ground water compliance monitoring during remedial action construction, and (3) to define the extent of contamination. At the processing site, the frequency and duration of sampling will be dependent upon the nature and extent of residual contamination and the compliance strategy chosen. The monitor well locations provide a representative distribution of sampling points to characterize ground water quality and ground water flow conditions in the vicinity of the sites. The list of analytes has been modified with time to reflect constituents that are related to uranium processing activities and the parameters needed for geochemical evaluation

Glufosinate ammonium clean-up procedure from water samples using SPE

Science.gov (United States)

Tayeb M., A.; Ismail B., S.; Mardiana-Jansar, K.; Ta, Goh Choo; Agustar, Hani Kartini

2015-09-01

For the determination of glufosinate ammonium residue in soil and water samples, different solid phase extraction (SPE) sorbent efficiency was studied. Four different SPE sorbents i.e.: CROMABOND PS-H+, CROMABOND PS-OH-, ISOLUTE ENV+, Water Sep-Pak and OASIS HLB were used. Sample clean-up performance was evaluated using high performance liquid chromatography (Agilent 1220 infinity LC) with fluorescence detector. Detection of FMO-derivatives was done at λ ex = 260 nm and λ em= 310 nm. OASIS HLB column was the most suitable for the clean-up in view of the overall feasibility of the analysis.

UMTRA Project water sampling and analysis plan, Gunnison, Colorado: Revision 1

International Nuclear Information System (INIS)

1994-11-01

This water sampling and analysis plan summarizes the results of previous water sampling activities and the plan for future water sampling activities, in accordance with the Guidance Document for Preparing Sampling and Analysis Plans for UMTRA Sites. A buffer zone monitoring plan for the Dos Rios Subdivision is included as an appendix. The buffer zone monitoring plan was developed to ensure continued protection to the public from residual contamination. The buffer zone is beyond the area depicted as contaminated ground water due to former milling operations. Surface remedial action at the Gunnison Uranium Mill Tailings Remedial Action Project site began in 1992; completion is expected in 1995. Ground water and surface water will be sampled semiannually at the Gunnison processing site and disposal site. Results of previous water sampling at the Gunnison processing site indicate that ground water in the alluvium is contaminated by the former uranium processing activities. Background ground water conditions have been established in the uppermost aquifer at the Gunnison disposal site. The monitor well locations provide a representative distribution of sampling points to characterize ground water quality and ground water flow conditions in the vicinity of the sites. The list of analytes has been modified with time to reflect constituents that are related to uranium processing activities and the parameters needed for geochemical evaluation

Characterisation of some South African water treatment residues ...

African Journals Online (AJOL)

2005-07-03

Jul 3, 2005 ... Land application of water treatment residue (WTR) the by-product from the production of potable water, is becoming the preferred ... were analysed for some physical (particle size distribution, particle density and plant available water) and chemical attributes ...... for Industrial Wastes – Theory and Practice.

Role of residual water hydrogen bonding in sugar/water/biomolecule systems: a possible explanation for trehalose peculiarity

Energy Technology Data Exchange (ETDEWEB)

Cordone, L; Cottone, G; Giuffrida, S [Dipartimento di Scienze Fisiche ed Astronomiche, Universita di Palermo and CNISM (Italy)

2007-05-23

We report on the set of experimental and simulative evidences which enabled us to suggest how biological structures embedded in a non-liquid water-saccharide solvent are anchored to the surrounding matrix via a hydrogen bond network. Such a network, whose rigidity increases by decreasing the sample water content, couples the degrees of freedom of the biostructure to those of the matrix and gives place to protein-saccharide-water structures (protein-solvent conformational substates). In particular, the whole set of data evidences that, while the protein-sugar interaction is well described in terms of a water entrapment hypothesis, the water replacement hypothesis better describes the sugar-membrane interaction; furthermore, it gives a hint towards the understanding of the origin of the trehalose peculiarity since the biomolecule-matrix coupling, specific to each particular sugar, always results in being the tightest for trehalose. In line with the heterogeneous dynamics in supercooled fluids and in carbohydrate glasses of different residual water contents, recent results confirm, at the single molecule level, the existence of protein-solvent conformational substates, spatially heterogeneous and interconverting, whose rigidity increases by lowering the sample hydration.

Nuclear reactor with makeup water assist from residual heat removal system

Science.gov (United States)

Corletti, Michael M.; Schulz, Terry L.

1993-01-01

A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit from an in-containment refueling water supply during staged depressurization leading up to passive emergency cooling by gravity feed from the refueling water storage tank, and flooding of the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and prevents flooding of the containment when such action is not necessary. Operation of the passive cooling system is not impaired. A high pressure makeup water storage tank is coupled to the reactor coolant circuit, holding makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal pumps move water from the refueling water storage tank into the coolant circuit as the coolant circuit is depressurized, preventing reaching the final depressurization stage unless the makeup coolant level continues to drop. The residual heat removal system can also be coupled in a loop with the refueling water supply tank, for an auxiliary heat removal path.

Nuclear reactor with makeup water assist from residual heat removal system

International Nuclear Information System (INIS)

Corletti, M.M.; Schulz, T.L.

1993-01-01

A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit from an in-containment refueling water supply during staged depressurization leading up to passive emergency cooling by gravity feed from the refueling water storage tank, and flooding of the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and prevents flooding of the containment when such action is not necessary. Operation of the passive cooling system is not impaired. A high pressure makeup water storage tank is coupled to the reactor coolant circuit, holding makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal pumps move water from the refueling water storage tank into the coolant circuit as the coolant circuit is depressurized, preventing reaching the final depressurization stage unless the makeup coolant level continues to drop. The residual heat removal system can also be coupled in a loop with the refueling water supply tank, for an auxiliary heat removal path. 2 figures

Nuclear reactor with makeup water assist from residual heat removal system

Science.gov (United States)

Corletti, M.M.; Schulz, T.L.

1993-12-07

A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit from an in-containment refueling water supply during staged depressurization leading up to passive emergency cooling by gravity feed from the refueling water storage tank, and flooding of the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and prevents flooding of the containment when such action is not necessary. Operation of the passive cooling system is not impaired. A high pressure makeup water storage tank is coupled to the reactor coolant circuit, holding makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal pumps move water from the refueling water storage tank into the coolant circuit as the coolant circuit is depressurized, preventing reaching the final depressurization stage unless the makeup coolant level continues to drop. The residual heat removal system can also be coupled in a loop with the refueling water supply tank, for an auxiliary heat removal path. 2 figures.

Selenium Adsorption To Aluminum-Based Water Treatment Residuals

Science.gov (United States)

Aluminum-based water treatment residuals (WTR) can adsorb water-and soil-borne P, As(V), As(III), and perchlorate, and may be able to adsorb excess environmental selenium. WTR, clay minerals, and amorphous aluminum hydroxide were shaken for 24 hours in selenate or selenite solut...

Model-based leakage localization in drinking water distribution networks using structured residuals

OpenAIRE

Puig Cayuela, Vicenç; Rosich, Albert

2013-01-01

In this paper, a new model based approach to leakage localization in drinking water networks is proposed based on generating a set of structured residuals. The residual evaluation is based on a numerical method based on an enhanced Newton-Raphson algorithm. The proposed method is suitable for water network systems because the non-linearities of the model make impossible to derive analytical residuals. Furthermore, the computed residuals are designed so that leaks are decoupled, which impro...

Prevalence of antimicrobial residues in eggs, tissue and feed samples in the State of Kuwait

International Nuclear Information System (INIS)

Alomirah, H.; Al-Mazeedi, H.; Al-Zenki, S.; Al-Faili, B.; Al-Foudary, M.; Abuzid, A.; Al-Sayed, I.; Sidhu, J.

2007-01-01

A total of 238 locally produced and imported eggs, tissue (meat, poultry and aquacultured fish) and feed and feedstuffs samples were collected at different seasonal periods from different farms and retail outlets in Kuwait and screened for presence of beta-lactams, tetracyclines, sulfonamides, streptomycin, macrolides and chloramphenicol (799 tests) using Charm II system. The results indicated that all of the 222 tests performed on table egg samples were negative for the analyzed antimicrobial residues indicating adherence to the guidelines for microbial use and withdrawal. Similarly, all of the 268 tests performed on tissue samples were negative for the analyzed antimicrobial residues except for chloramphenicol. These chloramphenicol positive samples, all of the 66 tests performed were negative for beta-lactams residues. Out of the 79 feed and feedstuff samples analyzed for teracyclines residues, broiler diet and concentrate samples (5%) were above the tetracyclines MRL (100 ppb.). On the other hands, results have revealed a widespread of sulfonamide residues and to a less extent chloramphenicol in tested feed and feedstuff samples. The Charm II system was reliable for rapid screening of antimicrobial residues. In general, results obtained in our study necessitate more effective and well planned national antimicrobial residues surveillance programs focusing particularly on samples imported from highly risk sources. (author)

Organochlorine and organophosphorus pesticide residues in fodder and milk samples along Musi river belt, India

Directory of Open Access Journals (Sweden)

Korrapati Kotinagu

2015-04-01

Full Text Available Aim: The present study was conducted to find the organochlorine pesticide (OCP and organophosphorus pesticide (OPP residues in fodder and milk samples along Musi river belt, India. Materials and Methods: Fodder and milk samples collected from the six zones of Musi river belt, Hyderabad India were analyzed by gas chromatography with electron capture detector for OCP residues and pulsated flame photometric detector for the presence of OPP residues. Results: The gas chromatographic analysis of fodder samples of Zone 5 of Musi river showed the residues of dicofol at concentration of 0.07±0.0007 (0.071-0.077. Among organophosphorus compounds, dimetheoate was present in milk samples collected from Zone 6 at a level of 0.13±0.006 (0.111-0.167. The residues of OCPs, OPPs and cyclodies were below the detection limit in the remaining fodder and milk samples collected from Musi river belt in the present study. Conclusion: The results indicate that the pesticide residues in fodder and milk samples were well below the maximum residue level (MRL values, whereas dicofol in fodder and dimethoate in milk were slightly above the MRL values specified by EU and CODEX.

Organochlorine and organophosphorus pesticide residues in fodder and milk samples along Musi river belt, India.

Science.gov (United States)

Kotinagu, Korrapati; Krishnaiah, Nelapati

2015-04-01

The present study was conducted to find the organochlorine pesticide (OCP) and organophosphorus pesticide (OPP) residues in fodder and milk samples along Musi river belt, India. Fodder and milk samples collected from the six zones of Musi river belt, Hyderabad India were analyzed by gas chromatography with electron capture detector for OCP residues and pulsated flame photometric detector for the presence of OPP residues. The gas chromatographic analysis of fodder samples of Zone 5 of Musi river showed the residues of dicofol at concentration of 0.07±0.0007 (0.071-0.077). Among organophosphorus compounds, dimetheoate was present in milk samples collected from Zone 6 at a level of 0.13±0.006 (0.111-0.167). The residues of OCPs, OPPs and cyclodies were below the detection limit in the remaining fodder and milk samples collected from Musi river belt in the present study. The results indicate that the pesticide residues in fodder and milk samples were well below the maximum residue level (MRL) values, whereas dicofol in fodder and dimethoate in milk were slightly above the MRL values specified by EU and CODEX.

Comparative analysis of different methods of extraction of present hydrocarbons in industrial residual waters

International Nuclear Information System (INIS)

Santa, Judith Rocio; Serrano, Martin; Stashenko, Elena

2002-01-01

A comparison among four extraction techniques such as: liquid - liquid (LLE) continuous and for lots, solid phase extraction (SPE), solid phase micro extraction (SPME) and static headspace (S-HS) was carried out. The main purpose of this research was to determine the highest recovery efficiencies and how reproducible the tests are while varying parameters such as time, extraction technique, type of solvents and others. Chromatographic parameters were optimized in order to carry out the analyses. Hydrocarbon's quantification of residual waters was achieved by using a high-resolution gas chromatography with a gas flame ionization detector (HRGC-FID). Validation of the method was carried out by analyzing real samples taken in different sampling places of the residual waters treatment plant of Ecopetrol - Barrancabermeja. The use of extraction methods that require big solvent quantities and long time for analysis are losing validity day by day. Techniques such as the HS-SPME and static HS are offered as alternatives for quantifying hydrocarbons. They show total lack of solvents, high sensibility, selectivity and the techniques are reproducible. Solid phase micro extraction (SPME) and static headspace (static HS) techniques were chosen as the extraction techniques to validate the method in real samples. Both techniques showed similar results for the determination of total hydrocarbons (in the gasoline range)

Evaluation of lyophilization for the preconcentration of natural water samples prior to neutron activation analysis

International Nuclear Information System (INIS)

Harrison, S.H.; LaFleur, P.D.; Zoller, W.H.

1975-01-01

Water is preconcentrated by freeze drying using a method which virtually eliminates sample contamination and trace element losses. To test the possibility of losses of volatile elements during the drying process, known quantities of radioactive tracers for 21 elements were added to water, the solutions freeze dried, and the tracer residues counted. The results confirm that at least 95 percent of all but the most volatile elements studied (Hg and I) were retained in the residue. The problem of transferring quantitatively the dry residue from the freeze drying container to an irradiation container was eliminated by designing a freeze drying container that would also serve as an irradiation and counting container. (U.S.)

Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

Disposing of coal combustion residues in inactive surface mines: Effects on water quality

International Nuclear Information System (INIS)

Kim, A.G.; Ackman, T.E.

1994-01-01

The disposal of coal combustion residues (CCR) in surface and underground coal mines can provide a stable, low-maintenance alternative to landfills, benefiting the mining and electric power industries. The material may be able to improve water quality at acid generating abandoned or reclaimed coal mine sites. Most combustion residues are alkaline, and their addition to the subsurface environment could raise the pH, limiting the propagation of pyrite oxidizing bacteria and reducing the rate of acid generation. Many of these CCR are also pozzolanic, capable of forming cementitious grouts. Grouts injected into the buried spoil may decrease its permeability and porosity, diverting water away from the pyritic material. Both mechanisms, alkaline addition and water diversion, are capable of reducing the amount of acid produced at the disposal site. The US Bureau of Mines is cooperating in a test of subsurface injection of CCR into a reclaimed surface mine. Initially, a mixture of fly ash, lime, and acid mine drainage (AMD) sludge was injected. Lime was the source of calcium for the formation of the pozzolanic grout. Changes in water quality parameters (pH, acidity, anions, and trace metals) in water samples from wells and seeps indicate a small but significant improvement after CCR injection. Changes in the concentration of heavy metals in the water flowing across the site were apparently influenced by the presence of flyash

The influence of the self-absorption on the measure of the total alpha activity in water samples

International Nuclear Information System (INIS)

Acena, M.L.; Gonzalez, J.A.; De Pablo, A.

1981-01-01

The self-absorption is an important difficulty in measuring α-activities in river water samples. A semiempirical equation for calculating the self-absorption versus sample thickness has been obtained. This equation is valid for the regular saline residues in spanish rivers and for thicknesses lower than 2 mg x cm -2 . This figure sets a limit for the amount of water to be evaporated from the sample. (author)

Water Solubility of Plutonium and Uranium Compounds and Residues at TA-55

International Nuclear Information System (INIS)

Reilly, Sean Douglas; Smith, Paul Herrick; Jarvinen, Gordon D.; Prochnow, David Adrian; Schulte, Louis D.; DeBurgomaster, Paul Christopher; Fife, Keith William; Rubin, Jim; Worl, Laura Ann

2016-01-01

Understanding the water solubility of plutonium and uranium compounds and residues at TA-55 is necessary to provide a technical basis for appropriate criticality safety, safety basis and accountability controls. Individual compound solubility was determined using published solubility data and solution thermodynamic modeling. Residue solubility was estimated using a combination of published technical reports and process knowledge of constituent compounds. The scope of materials considered includes all compounds and residues at TA-55 as of March 2016 that contain Pu-239 or U-235 where any single item in the facility has more than 500 g of nuclear material. This analysis indicates that the following materials are not appreciably soluble in water: plutonium dioxide (IDC=C21), plutonium phosphate (IDC=C66), plutonium tetrafluoride (IDC=C80), plutonium filter residue (IDC=R26), plutonium hydroxide precipitate (IDC=R41), plutonium DOR salt (IDC=R42), plutonium incinerator ash (IDC=R47), uranium carbide (IDC=C13), uranium dioxide (IDC=C21), U 3 O 8 (IDC=C88), and uranium filter residue (IDC=R26). This analysis also indicates that the following materials are soluble in water: plutonium chloride (IDC=C19) and uranium nitrate (IDC=C52). Equilibrium calculations suggest that PuOCl is water soluble under certain conditions, but some plutonium processing reports indicate that it is insoluble when present in electrorefining residues (R65). Plutonium molten salt extraction residues (IDC=R83) contain significant quantities of PuCl 3 , and are expected to be soluble in water. The solubility of the following plutonium residues is indeterminate due to conflicting reports, insufficient process knowledge or process-dependent composition: calcium salt (IDC=R09), electrorefining salt (IDC=R65), salt (IDC=R71), silica (IDC=R73) and sweepings/screenings (IDC=R78). Solution thermodynamic modeling also indicates that fire suppression water buffered with a commercially-available phosphate

Water Solubility of Plutonium and Uranium Compounds and Residues at TA-55

Energy Technology Data Exchange (ETDEWEB)

Reilly, Sean Douglas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Smith, Paul Herrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Jarvinen, Gordon D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Prochnow, David Adrian [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Schulte, Louis D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; DeBurgomaster, Paul Christopher [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Fife, Keith William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Rubin, Jim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States

2016-06-13

Understanding the water solubility of plutonium and uranium compounds and residues at TA-55 is necessary to provide a technical basis for appropriate criticality safety, safety basis and accountability controls. Individual compound solubility was determined using published solubility data and solution thermodynamic modeling. Residue solubility was estimated using a combination of published technical reports and process knowledge of constituent compounds. The scope of materials considered includes all compounds and residues at TA-55 as of March 2016 that contain Pu-239 or U-235 where any single item in the facility has more than 500 g of nuclear material. This analysis indicates that the following materials are not appreciably soluble in water: plutonium dioxide (IDC=C21), plutonium phosphate (IDC=C66), plutonium tetrafluoride (IDC=C80), plutonium filter residue (IDC=R26), plutonium hydroxide precipitate (IDC=R41), plutonium DOR salt (IDC=R42), plutonium incinerator ash (IDC=R47), uranium carbide (IDC=C13), uranium dioxide (IDC=C21), U₃O₈ (IDC=C88), and uranium filter residue (IDC=R26). This analysis also indicates that the following materials are soluble in water: plutonium chloride (IDC=C19) and uranium nitrate (IDC=C52). Equilibrium calculations suggest that PuOCl is water soluble under certain conditions, but some plutonium processing reports indicate that it is insoluble when present in electrorefining residues (R65). Plutonium molten salt extraction residues (IDC=R83) contain significant quantities of PuCl₃, and are expected to be soluble in water. The solubility of the following plutonium residues is indeterminate due to conflicting reports, insufficient process knowledge or process-dependent composition: calcium salt (IDC=R09), electrorefining salt (IDC=R65), salt (IDC=R71), silica (IDC=R73) and sweepings/screenings (IDC=R78). Solution thermodynamic modeling also indicates that fire suppression water buffered with a

Isolation of a bacteria of the Bacillus genus as indicator in the disinfection of residual waters by means of the ionizing radiation (e- , γ)

International Nuclear Information System (INIS)

Mata J, M.

2003-01-01

The pollutants of the water can be chemical, physical and biological. Among those biological we find to the microorganisms: bacterias, virus and protozoa. These cause important infections in many countries, mainly of Latin America. With the advance of the technology and the quick demographic growth, the biological pollution of the water has already become an important topic since it would damage the public health and it causes that their disinfection has greater attention. In the treatment of residual waters three basic treatments exist the one primary, secondary and tertiary; in this last we find the disinfection, which can be taken to end by chemical and physical methods. For this work of investigation it was used the ionizing radiation, because it is an innovative technology that it eliminates microorganisms in residual waters. The investigation consisted on treating, samples of residual water after the biological treatment of the plant RECICLAGUA with ionizing radiation (electrons and gammas), for the case of electrons it was used the dose of 0.5 kGy and for gamma the dose, of 5 kGy, later the survivor bacteria was isolated to these doses in both cases and they were carried out the tests of identification. In accordance with the obtained results can say that it is about a B. subtilis. The isolated B.subtilis was presented as a pollutant of the flora of the residual water, having a greater survival to the dose of 0.5 and 5 kGy with electrons and gammas, respectively that other present polluting microorganisms in the samples of residual water. For it fits signalize that this microorganism shows characteristics as it easy isolation and identification, the presence with pathogen microorganisms and a greater survival when being irradiated, therefore it can use as indicator in the disinfection of residual waters through ionizing radiation (electrons and gammas). (Author)

Nuclear reactor with makeup water assist from residual heat removal system

International Nuclear Information System (INIS)

Schulz, T.L.; Corletti, M.M.

1994-01-01

A pressurized water nuclear reactor uses its residual heat removal system to make up water in the reactor coolant circuit by pumping water from an in-containment refueling water storage tank during staged depressurization of the coolant circuit, the final stage including passive emergency cooling by gravity feed from the refueling water storage tank to the coolant circuit and to flood the containment building. When depressurization commences due to inadvertence or a manageable leak, the residual heat removal system is activated manually and avoids the final stage of depressurization with its flooding of the containment when such action is not necessary, but does not prevent the final stage when it is necessary. A high pressure makeup water storage tank coupled to the reactor coolant circuit holds makeup coolant at the operational pressure of the reactor. The staged depressurization system vents the coolant circuit to the containment, thus reducing the supply of makeup coolant. The level of makeup coolant can be sensed to trigger opening of successive depressurization conduits. The residual heat removal system can also be coupled in a loop with the refueling water supply tanks for cooling the tank. (Author)

Headspace Solid Phase Microextraction in Pesticide Residues Analysis: 2. Apple Samples

Directory of Open Access Journals (Sweden)

Jelena Milinović

2007-01-01

Full Text Available Headspace solid phase microextraction method (HS/SPME, optimised previously for pesticide water solutions, was applied to trace residues of the pesticides chlorpyrifos, fenthion and bifenthrin in apple samples. One-hour extraction procedure was performed at 60oC extraction temperature. Nonpolar polydimethyl siloxane (PDMS fiber was used. Detection and quantification were carried out by gas chromatography/mass spectrometry (GC/MS. A non-pesticide treated apple sample was fortified with the pesticides over a 0.025-1.25 mg/kg concentration range in order to determine analytical parameters of the method applied. Linearity with regression coefficient (R values higher than 0.99 were obtained over the whole concentration range investigated for chlorpyrifos and fenthion, while linear dependence was observed in the 0.1-1.25 mg/kg range for bifenthrin. Relative recovery values for samples fortified at different levels were in the 56.68-82.91% range. Limit of detection (LOD values were determined as follows: 0.014 mg/kg for chlorpyrifos, 0.021 mg/kg for fenthion and 0.053 mg/kg for bifenthrin. Relative standard deviation (RSD values obtained for multiple analysis of the sample fortified at 0.6 mg/kg level were not higher than 20%.

Field sampling of residual aviation gasoline in sandy soil

International Nuclear Information System (INIS)

Ostendorf, D.W.; Hinlein, E.S.; Yuefeng, Xie; Leach, L.E.

1991-01-01

Two complementary field sampling methods for the determination of residual aviation gasoline content in the contaminated capillary fringe of a fine, uniform, sandy soil were investigated. The first method featured field extrusion of core barrels into pint-size Mason jars, while the second consisted of laboratory partitioning of intact stainless steel core sleeves. Soil samples removed from the Mason jars (in the field) and sleeve segments (in the laboratory) were subjected to methylene chloride extraction and gas chromatographic analysis to compare their aviation gasoline content. The barrel extrusion sampling method yielded a vertical profile with 0.10m resolution over an essentially continuous 5.0m interval from the ground surface to the water table. The sleeve segment alternative yielded a more resolved 0.03m vertical profile over a shorter 0.8m interval through the capillary fringe. The two methods delivered precise estimates of the vertically integrated mass of aviation gasoline at a given horizontal location, and a consistent view of the vertical profile as well. In the latter regard, a 0.2m thick lens of maximum contamination was found in the center of the capillary fringe, where moisture filled all voids smaller than the mean pore size. The maximum peak was resolved by the core sleeve data, but was partially obscured by the barrel extrusion observations, so that replicate barrels or a half-pint Mason jar size should be considered for data supporting vertical transport analyses in the absence of sleeve partitions

Estimation of polycyclic aromatic hydrocarbon concentrations in the water column based on tissue residues in mussels and salmon: An equilibrium partitioning approach

International Nuclear Information System (INIS)

Neff, J.M.; Burns, W.A.

1996-01-01

Equilibrium partitioning was used to estimate concentrations of dissolved polycyclic aromatic hydrocarbons (PAHs) in the water column from PAH residues in tissues of mussels and juvenile pink salmon collected from coastal marine waters affected by the Exxon Valdez oil spill. Estimated concentrations were within factors of 2 to 5 for fish and 5 to 10 for mussels of average total dissolved and particulate PAHs measured in concurrent water samples. Temporal trends of estimated and measured water-column PAH concentrations were comparable. Water-column PAH concentrations estimated from residues in tissues of mussels (Mytilus trossulus) were higher than estimates based on residues in tissues of juvenile pink salmon (Oncorhynchus gorbuscha). Possible reasons for this difference include seasonal variations in mussel lipid content, differences in PAH uptake and depuration rates between fish and mussels, differences in how fish and mussels interact with particulate oil, and possible short exposure times for juvenile pink salmon. All of these factors may play a role. In any event, estimates of dissolved PAHs in the water column, based on PAH residues in either fish or mussel tissue, confirm that PAH concentrations generally did not exceed water quality standards for protection of marine life

UMTRA project water sampling and analysis plan, Salt Lake City, Utah

International Nuclear Information System (INIS)

1994-06-01

Surface remedial action was completed at the Salt Lake City, Utah, Uranium Mill Tailings Remedial Action (UMTRA) Project site in the fall of 1987. Results of water sampling for the years 1992 to 1994 indicate that site-related ground water contamination occurs in the shallow unconfined aquifer (the uppermost aquifer). With respect to background ground water quality, contaminated ground water in the shallow, unconfined aquifer has elevated levels of chloride, sodium, sulfate, total dissolved solids, and uranium. No contamination associated with the former tailings pile occurs in levels exceeding background in ground water in the deeper confined aquifer. This document provides the water sampling and analysis plan for ground water monitoring at the former uranium processing site in Salt Lake City, Utah (otherwise known as the ''Vitro'' site, named after the Vitro Chemical Company that operated the mill). All contaminated materials removed from the processing site were relocated and stabilized in a disposal cell near Clive, Utah, some 85 miles west of the Vitro site (known as the ''Clive'' disposal site). No ground water monitoring is being performed at the Clive disposal site, since concurrence of the remedial action plan by the US Nuclear Regulatory Commission and completion of the disposal cell occurred before the US Environmental Protection Agency issued draft ground water standards in 1987 (52 FR 36000) for cleanup, stabilization, and control of residual radioactive materials at the disposal site. In addition, the likelihood of post-closure impact on the ground water is minimal to nonexistent, due to the naturally poor quality of the ground water. Water sampling activities planned for calendar year 1994 consist of sampling ground water from nine monitor wells to assess the migration of contamination within the shallow unconfined aquifer and sampling ground water from two existing monitor wells to assess ground water quality in the confined aquifer

Levels of pesticides residues in the White Nile water in the Sudan.

Science.gov (United States)

Nesser, Gibreel A A; Abdelbagi, Azhari O; Hammad, Ahmed Mohammed Ali; Tagelseed, Mirghani; Laing, Mark D

2016-06-01

Twenty-two commonly used pesticides were monitored during autumn, winter, and summer of 2004-2005 in 27 water samples from three sites along the White Nile in Sudan (former Sudan). Sites were selected to reflect pesticides gathered from drainage canals in central Sudan and from upstream sources. Collected samples were extracted and subjected to gas chromatographic analysis. Pesticides levels were measured in nanograms per liter. Pesticides residues were detected in 96 % of the samples with a total residue burden of 4132.6 ng L(-1), and an overall mean concentration and range of 50.99 and not detected-1570 ng L(-1), respectively. Ororganochlorines were the most frequently detected contaminants, which were found in 70 % of the samples, causing a total burden of 2852.8 ng L(-1), followed by pyrethroids 15 % of the samples, with a total burden of 926.5 ng L(-1). The tested herbicides were detected in ˂4 % of the samples with a total burden of 353.3 ng L(-1), while organophosphorus levels were below the detection limit. The most frequent contaminants were the following: heptachlor and its epoxide (52 % of samples), followed by DDTs (dichlorodiphenyltrichloroethanes) (DDT and DDE, in 19 % of the samples), cypermethrin and fenvalerate (in 11 % of the samples), and pendimethalin (in oxyfluorfen were not detected in the analyzed samples. Generally, levels were least in autumn, and followed by summer and winter. Sources of contamination might include agricultural lands in central Sudan and upstream sources. Both recent and old contaminations were indicated.

Selenium-Water Treatment Residual Adsorption And Characterization

Science.gov (United States)

Aluminum-based water treatment residuals (WTR) have the ability to adsorb tremendous quantities of soil-borne P, and have been shown to adsorb other anions, such as As (V), As (III), and ClO4-. Environmental issues associated with Se in the Western US led us to study W...

The effect of sludge water treatment plant residuals on the properties of compressed brick

Science.gov (United States)

Shamsudin, Shamrul-Mar; Shahidan, S.; Azmi, M. A. M.; Ghaffar, S. A.; Ghani, M. B. Abdul; Saiful Bahari, N. A. A.; Zuki, S. S. M.

2017-11-01

The focus of this study is on the production of compressed bricks which contains sludge water treatment plant (SWTP) residuals obtained from SAJ. The main objective of this study is to utilise and incorporate discarded material (SWTP) in the form of residual solution to produce compressed bricks. This serves as one of the recycling efforts to conserve the environment. This study determined the optimum mix based on a mix ratio of 1:2:4 (cement: sand: soil) in the production of compressed bricks where 5 different mixes were investigated i. e. 0%, 5%, 10%, 20%, and 30% of water treatment plant residue solution. The production of the compressed bricks is in accordance with the Malaysian Standard MS 7.6: 1972 and British Standard BS 3921: 1985 - Compressive Strength & Water Absorption. After being moulded and air dried, the cured bricks were subjected to compression tests and water absorption tests. Based on the tests conducted, it was found that 20% of water treatment plant residue solution which is equivalent to 50% of soil content replacement with a mix composition of [10: cement] [20: sand] [20: soil] [20: water treatment plant residue solution] is the optimum mix. It was also observed that the bricks containing SWTP residuals were lighter in weight compared to the control specimens

Residual stress improvement in multi-layer welded plates using water-shower cooling during welding process

International Nuclear Information System (INIS)

Yanagida, Nobuyoshi; Koide, Hiroo

2006-01-01

To reduce tensile residual stress in a welded region, we developed a new welding method that applies a water-shower behind the welding torch. When this method is applied to welding of austenitic stainless steel plates, cooling conditions mainly determine how much the residual stress can be reduced. To determine the conditions, we first used FEM to evaluate the effects of interpass temperature on the residual stress. And we found effective conditions for reducing tensile residual stress. To verify the validity of the conditions, specimens welded with or without water shower cooling were manufactured. Residual stresses of the specimens were experimentally measured. It was found that tensile residual stresses were generated on the surface of the welds and those were reduced in the case that the water-shower was applied. These measurement results agree well with the FEM analyses. It can therefore be concluded that the water-shower cooling during welding is appropriate for reducing tensile residual stress in austenitic stainless steel welding. (author)

Antimicrobial residues in animal waste and water resources proximal to large-scale swine and poultry feeding operations

Science.gov (United States)

Campagnolo, E.R.; Johnson, K.R.; Karpati, A.; Rubin, C.S.; Kolpin, D.W.; Meyer, M.T.; Esteban, J. Emilio; Currier, R.W.; Smith, K.; Thu, K.M.; McGeehin, M.

2002-01-01

Expansion and intensification of large-scale animal feeding operations (AFOs) in the United States has resulted in concern about environmental contamination and its potential public health impacts. The objective of this investigation was to obtain background data on a broad profile of antimicrobial residues in animal wastes and surface water and groundwater proximal to large-scale swine and poultry operations. The samples were measured for antimicrobial compounds using both radioimmunoassay and liquid chromatography/electrospray ionization-mass spectrometry (LC/ESI-MS) techniques. Multiple classes of antimicrobial compounds (commonly at concentrations of >100 μg/l) were detected in swine waste storage lagoons. In addition, multiple classes of antimicrobial compounds were detected in surface and groundwater samples collected proximal to the swine and poultry farms. This information indicates that animal waste used as fertilizer for crops may serve as a source of antimicrobial residues for the environment. Further research is required to determine if the levels of antimicrobials detected in this study are of consequence to human and/or environmental ecosystems. A comparison of the radioimmunoassay and LC/ESI-MS analytical methods documented that radioimmunoassay techniques were only appropriate for measuring residues in animal waste samples likely to contain high levels of antimicrobials. More sensitive LC/ESI-MS techniques are required in environmental samples, where low levels of antimicrobial residues are more likely.

Antimicrobial residues in animal waste and water resources proximal to large-scale swine and poultry feeding operations.

Science.gov (United States)

Campagnolo, Enzo R; Johnson, Kammy R; Karpati, Adam; Rubin, Carol S; Kolpin, Dana W; Meyer, Michael T; Esteban, J Emilio; Currier, Russell W; Smith, Kathleen; Thu, Kendall M; McGeehin, Michael

2002-11-01

Expansion and intensification of large-scale animal feeding operations (AFOs) in the United States has resulted in concern about environmental contamination and its potential public health impacts. The objective of this investigation was to obtain background data on a broad profile of antimicrobial residues in animal wastes and surface water and groundwater proximal to large-scale swine and poultry operations. The samples were measured for antimicrobial compounds using both radioimmunoassay and liquid chromatography/electrospray ionization-mass spectrometry (LC/ESI-MS) techniques. Multiple classes of antimicrobial compounds (commonly at concentrations of > 100 microg/l) were detected in swine waste storage lagoons. In addition, multiple classes of antimicrobial compounds were detected in surface and groundwater samples collected proximal to the swine and poultry farms. This information indicates that animal waste used as fertilizer for crops may serve as a source of antimicrobial residues for the environment. Further research is required to determine if the levels of antimicrobials detected in this study are of consequence to human and/or environmental ecosystems. A comparison of the radioimmunoassay and LC/ESI-MS analytical methods documented that radioimmunoassay techniques were only appropriate for measuring residues in animal waste samples likely to contain high levels of antimicrobials. More sensitive LC/ESI-MS techniques are required in environmental samples, where low levels of antimicrobial residues are more likely.

Assessment of heavy metal residues in water, fish tissue and human ...

African Journals Online (AJOL)

MICHAEL HORSFALL

ABSTRACT: Residual levels of lead, chromium, cadmium and zinc in water and fish tissue from. Ubeji River ... Key Words : Heavy metal residues , Fish tissue, Human blood, Ubeji River. ... is of critical concern because of their toxicity and.

Seasonal and spatial variations of glyphosate residues in surface waters of El Crespo stream, Buenos Aires province, Argentina.

Science.gov (United States)

Perez, Debora; Okada, Elena; Aparicio, Virginia; Menone, Mirta; Costa, Jose Luis

2017-04-01

El Crespo stream is located inside a small watershed (52,000 Ha) which is only influenced by farming activities without urban or industrial impact. The watershed can be divided in two areas, the southern area (upstream), mainly composed of intensive crops and the northern area (downstream) used only for extensive livestock. In this sense, "El Crespo" stream in an optimal site for monitoring screening of pesticide residues. The objective of this work was to determine the seasonal and spatial variations of glyphosate (GLY), in surface waters of "El Crespo" stream. We hypothesized that in surface waters of "El Crespo" stream the levels of GLY vary depending of the season and rainfall events. The water sampling was carried out from October to June (2014-2015) in two sites: upstream (US) and downstream (DS), before and after rain events. The water samples were collected by triplicate in 1 L polypropylene bottles and stored at -20°C until analysis. GLY was extracted from unfiltered water samples with a buffer solution (100 mM Na2B4O7•10H2O/100 mM K3PO4, pH=9) and derivatized with 9-fluorenylmethylchloroformate (1 mg/mL in acetonitrile). Afterwards samples were analyzed using liquid chromatography coupled to a tandem mass spectrometer (UPLC-MS/MS). The detection limit (LD) was 0.1 μg/L and the quantification limit (QL) was 0.5 μg/L. The rainfall regime was obtained from the database of INTA Balcarce. GLY was detected in 92.3% of the analyzed samples. In the US site, were GLY is regularly applied, the highest GLY concentration was registered in October (2.15 ± 0.16 μg/L); from November to June, the GLY levels decreased from 1.97 ± 0.17 μg/L to rain falls. On the rest of the months, the rainfall events were scarce and the GLY concentrations decreased in both. These results indicated that in the El Crespo stream the GLY residues vary according the applications in the field and the rainfall regime and the DS site is probably a sump of GLY residues applied upstream in

Interactive effects of rice residue and water stress on growth and metabolism of wheat seedlings

Directory of Open Access Journals (Sweden)

Nimisha Amist

2014-08-01

Full Text Available In the present study effects of rice residue with and without water stress were studied on Triticum aestivum L. cv. Shatabadi. The mixture of residue and garden soil in 1:1 ratio was considered as 50% (R1 and only decomposed residue as 100% (R2. Garden soil was taken as control. Twenty five seeds were sown in each experimental trays filled with soil mixture according to the treatments. Trays were arranged in two groups. After 15 days one set was subjected to water stress (WS by withholding water supply for 3 days. Morphological and biochemical parameters of 18 days old seedlings were recorded. Seedling height decreased in all treatments. A gradual decrease in relative water content, pigment and protein contents of wheat seedlings were observed. Sugar and proline contents increased in treatments. An increase in malondialdehyde (MDA content and antioxidative enzyme activities was recorded. Elevation in catalase activity was observed in all treatments except in plants with water deficit. Ascorbate peroxidase (APX and guaiacol peroxidase (GPX activities increased when residue mixed with soil but decreased in seedlings under the combined influence of the residue and water stress. Higher amount of MDA and lower activities of APX and GPX reflected the oxidative damage in seedlings under combined treatments. Rice residue inhibited growth of wheat seedlings. Water stress intensified the effects of residue.

Development and evaluation of a gas chromatographic method for the determination of triazine herbicides in natural water samples

Science.gov (United States)

Steinheimer, T.R.; Brooks, M.G.

1984-01-01

A multi-residue method is described for the determination of triazine herbicides in natural water samples. The technique uses solvent extraction followed by gas chromatographic separation and detection employing nitrogen-selective devices. Seven compounds can be determined simultaneously at a nominal detection limit of 0.1 ??g/L in a 1-litre sample. Three different natural water samples were used for error analysis via evaluation of recovery efficiencies and estimation of overall method precision. As an alternative to liquid-liquid partition (solvent extraction) for removal of compounds of interest from water, solid-phase extraction (SPE) techniques employing chromatographic grade silicas with chemically modified surfaces have been examined. SPE is found to provide rapid and efficient concentration with quantitative recovery of some triazine herbicides from natural water samples. Concentration factors of 500 to 1000 times are obtained readily by the SPE technique.A multi-residue method is described for the determination of triazine herbicides in natural water samples. The technique uses solvent extraction followed by gas chromatographic separation and detection employing nitrogen-selective devices. Seven compounds can be determined simultaneously at a nominal detection limit of 0. 1 mu g/L in a 1-litre sample. As an alternative to liquid-liquid partition (solvent extraction) for removal of compounds of interest from water, solid-phase extraction (SPE) techniques employing chromatographic grade silicas with chemically modified surfaces have been examined. SPE is found to provide rapid and efficient concentration with quantitative recovery of some triazine herbicides from natural water samples. Concentration factors of 500 to 1000 times are obtained readily by the SPE technique.

Monitoring and removal of residual phthalate esters and pharmaceuticals in the drinking water of Kaohsiung City, Taiwan.

Science.gov (United States)

Yang, Gordon C C; Yen, Chia-Heng; Wang, Chih-Lung

2014-07-30

This study monitored the occurrence and removal efficiencies of 8 phthalate esters (PAEs) and 13 pharmaceuticals present in the drinking water of Kaohsiung City, Taiwan. The simultaneous electrocoagulation and electrofiltration (EC/EF) process was used to remove the contaminants. To this end, a monitoring program was conducted and a novel laboratory-prepared tubular carbon nanofiber/carbon/alumina composite membrane (TCCACM) was incorporated into the EC/EF treatment module (collectively designated as "TCCACM-EC/EF treatment module") to remove the abovementioned compounds from water samples. The monitoring results showed that the concentrations of PAEs were lower in water samples from drinking fountains as compared with tap water samples. No significant differences were found between the concentrations of pharmaceuticals in the two types of water samples. Under optimal operating conditions, the TCCACM-EC/EF treatment module yielded the lowest residual concentrations, ranging from not detected (ND) to 52ng/L for PAEs and pharmaceuticals of concern in the tap water samples. Moreover, the performance of the TCCACM-EC/EF treatment module is comparable with a series of treatment units employed for the drinking fountain water treatment system. The relevant removal mechanisms involved in the TCCACM-EC/EF treatment module were also discussed in this work. Copyright © 2014 Elsevier B.V. All rights reserved.

Determination of Residual Chlorine and Turbidity in Drinking Water. Instructor's Manual.

Science.gov (United States)

Office of Water Program Operations (EPA), Cincinnati, OH. National Training and Operational Technology Center.

This instructor's guide presents analytical methods for residual chlorine and turbidity. Topics include sample handling, permissable concentration levels, substitution of residual chlorine for bacteriological work, public notification, and the required analytical techniques to determine residual chlorine and turbidity. This publication is intended…

Determination of Residual Chlorine and Turbidity in Drinking Water. Student Manual.

Science.gov (United States)

Office of Water Program Operations (EPA), Cincinnati, OH. National Training and Operational Technology Center.

This student's manual covers analytical methods for residual chlorine and turbidity. Topics include sample handling, permissable concentration levels, substitution of residual chlorine for bacteriological work, public notification, and the required analytical techniques to determine residual chlorine and turbidity. The publication is intended for…

From municipal sewage to drinking water: fate and removal of pharmaceutical residues in the aquatic environment in urban areas.

Science.gov (United States)

Heberer, Th; Reddersen, K; Mechlinski, A

2002-01-01

Recently, the occurrence and fate of pharmaceutically active compounds (PhACs) in the aquatic environment was recognized as one of the emerging issues in environmental chemistry and as a matter of public concern. Residues of PhACs have been found as contaminants in sewage, surface, and ground- and drinking water samples. Since June 2000, a new long-term monitoring program of sewage, surface, ground- and drinking water has been carried out in Berlin, Germany. Samples, collected periodically from selected sites in the Berlin area, are investigated for residues of PhACs and related contaminants. The purpose of this monitoring is to investigate these compounds over a long time period to get more reliable data on their occurrence and fate in the different aquatic compartments. Moreover, the surface water investigations allow the calculation of season-dependent contaminant loads in the Berlin waters. In the course of the monitoring program, PhACs and some other polar compounds were detected at concentrations up to the microg/L-level in all compartments of the Berlin water cycle. The monitoring is accompanied and supported by several other investigations such as laboratory column experiments and studies on bank filtration and drinking water treatment using conventional or membrane filtration techniques.

Effect of water content and organic carbon on remote sensing of crop residue cover

Science.gov (United States)

Serbin, G.; Hunt, E. R., Jr.; Daughtry, C. S. T.; McCarty, G. W.; Brown, D. J.; Doraiswamy, P. C.

2009-04-01

Crop residue cover is an important indicator of tillage method. Remote sensing of crop residue cover is an attractive and efficient method when compared with traditional ground-based methods, e.g., the line-point transect or windshield survey. A number of spectral indices have been devised for residue cover estimation. Of these, the most effective are those in the shortwave infrared portion of the spectrum, situated between 1950 and 2500 nm. These indices include the hyperspectral Cellulose Absorption Index (CAI), and advanced multispectral indices, i.e., the Lignin-Cellulose Absorption (LCA) index and the Shortwave Infrared Normalized Difference Residue Index (SINDRI), which were devised for the NASA Terra Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor. Spectra of numerous soils from U.S. Corn Belt (Indiana and Iowa) were acquired under wetness conditions varying from saturation to oven-dry conditions. The behavior of soil reflectance with water content was also dependent on the soil organic carbon content (SOC) of the soils, and the location of the spectral bands relative to significant water absorptions. High-SOC soils showed the least change in spectral index values with increase in soil water content. Low-SOC soils, on the other hand, showed measurable difference. For CAI, low-SOC soils show an initial decrease in index value followed by an increase, due to the way that water content affects CAI spectral bands. Crop residue CAI values decrease with water content. For LCA, water content increases decrease crop residue index values and increase them for soils, resulting in decreased contrast. SINDRI is also affected by SOC and water content. As such, spatial information on the distribution of surface soil water content and SOC, when used in a geographic information system (GIS), will improve the accuracy of remotely-sensed crop residue cover estimates.

Veterinary antibiotic resistance, residues, and ecological risks in environmental samples obtained from poultry farms, Egypt.

Science.gov (United States)

Dahshan, Hesham; Abd-Elall, Amr Mohamed Mohamed; Megahed, Ayman Mohamed; Abd-El-Kader, Mahdy A; Nabawy, Ehab Elsayed

2015-02-01

In Egypt, poultry production constitutes one of the main sources of pollution with veterinary antibiotics (VAs) into the environment. About 80 % of meat production in Egypt is of poultry origin, and the potential environmental risks associated with the use of VAs in these farms have not yet been properly evaluated. Thus, the main purpose of this research was to evaluate the prevalence of antibiotic-resistant enteric key bacteria and the incidence of residual antibiotics in poultry farm environmental samples and to determine whether fertilizing soils with poultry litter from farms potentially brings ecological risks. From December 2011 to September 2012, a total of 225 litter, bird dropping, and water samples were collected from 75 randomly selected boiler poultry farms. A high prevalence of Escherichia coli (n = 179; 79.5 %) in contrast to the low prevalence of Salmonella spp. (n = 7; 3.1 %) was detected. Amongst E. coli isolates, serotypes O142:K86, O125:K70, O91:K, and O119:K69 were the most common. Meanwhile, Salmonella enterica serotypes emek and enteritidis were recovered. The antibiograms using the disc diffusion method revealed significantly more common resistant and multi-resistant isolates in broiler poultry farms. Residues of tetracycline and ciprofloxacin were detected at 2.125 and 1.401 mg kg(-1) mean levels, respectively, in environmental samples contaminated with E. coli-resistant strains by HPLC. The risk evaluations highlighted that tetracycline residues in poultry litter significantly display environmental risks with a hazard quotient value above 1 (1.64). Our study implies that ineffective implementation of veterinary laws which guide and guard against incorrect VA usage may potentially bring health and environmental risks.

Simultaneous Determination of TetracyclinesResidues in Bovine Milk Samples by Solid Phase Extraction and HPLC-FL Method

Directory of Open Access Journals (Sweden)

Mehra Mesgari Abbasi

2011-06-01

Full Text Available Introduction:Tetracyclines (TCs are widely used in animal husbandry and their residues in milk may resultinharmful effects on human. The aim of this study was to investigate the presence of TCs residues in various bovine milk samples from local markets of Ardabil, Iran. Methods:One hundred and fourteen pasteurized, sterilized and raw milk samples were collected from markets of Ardabil. Tetracycline, Oxytetracycline and Chlortetracycline (TCs residues extraction carried out by Solid Phase Extraction method. Determination of TCs residues were performed by high performance liquid chromatography (HPLC method using Fluorescence detector.Results: The mean of total TCs residues in all samples (114 samples was 97.6 ±16.9ng/g and that of pasteurized, sterilized and raw milk samples were 87.1 ± 17.7, 112.0 ± 57.3 and 154.0 ± 66.3ng/g respectively. Twenty five point four percent of the all samples, and24.4%, 30% and 28.6% of the pasteurized, sterilized and raw milk samples, respectively had higher TCs residues than the recommended maximum levels (100ng/g. Conclusion:This study indicates the presence of tetracycline residues more than allowed amount. Regulatory authorities should ensure proper withdrawal period before milking the animals and definite supervisions are necessary on application of these drugs.

USAGE OF ALGAE SPECIES CHAETOMORPHA GRACILIS AND CH. AEREA FOR DEPURATION PROCESS OF THE RESIDUAL WATERS

Directory of Open Access Journals (Sweden)

SALARU VICTOR

2008-11-01

Full Text Available Rapid increase of the population on the globe scale imposes maximum exploration of the natural resources and first of all of the aquatic resources. As a result are obtained an enormous quantity of residual waters which pollute the waters from rivers, lakes, freatic and underground waters. Elaboration of the depuration methods for residual waters the quantity of which grows continuously, is one of the most up to dated issue of the world. The physical-chemical depuration methods of the residual waters are very expensive and lack the efficiency we would like to have. The most efficient method proved to be the biological method using some species of algae and superior aquatic plants. In our experiences we have involved filamentous green algae Chaetomorpha gracilis and Ch. aerea for depuration of the sewerage water from town Cimishlia. The concentration of the mineral nitrogen compounds in the residual water is around 92,5 mg/l, and of the phosphates 10,1 mg/l. There were used the following concentration of the sewerage water: 10%, 25% and 50%. The most intense development of algae Chaetomorpha aerea was observed in the variant with 10% of residual water, in which the total concentration of the nitrogen was 10,24 mg/l, and of the phosphates 1,05 mg/l. For this variant the depuration water level was about 56,9%. For the case with Chaetomorpha gracilis, the depuration level for the same concentration of the residual water constituted 55,9 %. Increase of the concentration of the polluted water inhibits development of the algae reducing to the minimum their capacity to assimilate the nitrogen and the phosphor. In the solutions with 50 % of residual waters, the algae didn't die, but at the same time they didn't develop. From this results that both algae may be used in the phytoamelioration of the residual waters being diluted at 10% with purified water.

Pesticide residue determination in surface waters by stir bar sorptive extraction and liquid chromatography/tandem mass spectrometry.

Science.gov (United States)

Giordano, A; Fernández-Franzón, M; Ruiz, M J; Font, G; Picó, Y

2009-03-01

In this stir bar sorptive extraction (SBSE) method, 16 pesticides were extracted from surface water samples by sorption onto 1 mm polydimethylsiloxane layer coated on a 10-mm-length stir bar magnet. After liquid desorption of the analytes with 1 ml of methanol, the detection was performed on a liquid chromatography-tandem mass spectrometry with a triple quadrupole (QqQ) analyzer using selected reaction monitoring mode via electrospray ionization. Parameters affecting SBSE operation, including sample volume, salt addition, extraction time, stirring rate, and desorption conditions, have been evaluated. The optimized SBSE method required two 50 ml aliquots of surface water samples, one aliquot was added of 30% NaCl and stirred at 900 rpm during 1 h for testing five pesticides with log K(o/w) 3. The method was validated in spiked surface water samples at limits of quantifications (LOQs) and ten times the LOQs showing recoveries Albufera Lake and surrounding channels, showing that SBSE is a powerful tool for routine control analysis of pesticide residues in surface water.

Solid-phase extraction combined with high-performance liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry analysis of pesticides in water: method performance and application in a reconnaissance survey of residues in drinking water in Greater Cairo, Egypt.

Science.gov (United States)

Potter, Thomas L; Mohamed, Mahmoud A; Ali, Hannah

2007-01-24

Monitoring of water resources for pesticide residues is often needed to ensure that pesticide use does not adversely impact the quality of public water supplies or the environment. In many rural areas and throughout much of the developing world, monitoring is often constrained by lack of testing facilities; thus, collection of samples and shipment to centralized laboratories for analysis is required. The portability, ease of use, and potential to enhance analyte stability make solid-phase extraction (SPE) an attractive technique for handling water samples prior to their shipment. We describe performance of an SPE method targeting a structurally diverse mixture of 25 current-use pesticides and two common degradates in samples of raw and filtered drinking water collected in Greater Cairo, Egypt. SPE was completed in a field laboratory in Egypt, and cartridges were shipped to the United States for elution and high-performance liquid chromatography-atmospheric pressure chemical ionization-mass spectrometry analysis. Quantitative and reproducible recovery of 23 of 27 compounds (average = 96%; percent relative standard deviation = 21%) from matrix spikes (1 microg L-1 per component) prepared in the field and from deionized water fortified similarly in the analytical laboratory was obtained. Concurrent analysis of unspiked samples identified four parent compounds and one degradate in drinking water samples. No significant differences were observed between raw and filtered samples. Residue levels in all cases were below drinking water and "harm to aquatic-life" thresholds, indicating that human and ecological risks of pesticide contamination were relatively small; however, the study was limited in scale and scope. Further monitoring is needed to define spatial and temporal variation in residue concentrations. The study has demonstrated the feasibility of performing studies of this type using SPE to extract and preserve samples in the field. The approach should be broadly

Pesticide residues and microbial contamination of water resources in the MUDA rice agroecosystem

International Nuclear Information System (INIS)

Cheah Uan Boh; Lum Keng Yeang

2002-01-01

Studies on the water resources of the Muda rice growing areas revealed evidence of pesticide residues in the agroecosystem. While the cyclodiene endosulfan was found as a ubiquitous contaminant, the occurrence of other organochlorine insecticides was sporadic. The presence of 2,4-D, paraquat and molinate residues was also evident but the occurrence of these herbicides was seasonal. Residue levels of molinate were generally higher than those from the other herbicides. The problem of thiobencarb and carbofuran residues was not encountered. Analyses for microbial contamination revealed that the water resources were unfit for drinking; coliform counts were higher during certain periods of the year than others. (Author)

Cold vacuum drying residual free water test description

International Nuclear Information System (INIS)

Pajunen, A.L.

1997-01-01

Residual free water expected to remain in a Multi-Canister Overpack (MCO) after processing in the Cold Vacuum Drying (CVD) Facility is investigated based on three alternative models of fuel crevices. Tests and operating conditions for the CVD process are defined based on the analysis of these models. The models consider water pockets constrained by cladding defects, water constrained in a pore or crack by flow through a porous bed, and water constrained in pores by diffusion. An analysis of comparative reaction rate constraints is also presented indicating that a pressure rise test can be used to show MCO's will be thermally stable at operating temperatures up to 75 C

Reactor water sampling device

International Nuclear Information System (INIS)

Sakamaki, Kazuo.

1992-01-01

The present invention concerns a reactor water sampling device for sampling reactor water in an in-core monitor (neutron measuring tube) housing in a BWR type reactor. The upper end portion of a drain pipe of the reactor water sampling device is attached detachably to an in-core monitor flange. A push-up rod is inserted in the drain pipe vertically movably. A sampling vessel and a vacuum pump are connected to the lower end of the drain pipe. A vacuum pump is operated to depressurize the inside of the device and move the push-up rod upwardly. Reactor water in the in-core monitor housing flows between the drain pipe and the push-up rod and flows into the sampling vessel. With such a constitution, reactor water in the in-core monitor housing can be sampled rapidly with neither opening the lid of the reactor pressure vessel nor being in contact with air. Accordingly, operator's exposure dose can be reduced. (I.N.)

“Nanofiltration” Enabled by Super-Absorbent Polymer Beads for Concentrating Microorganisms in Water Samples

Science.gov (United States)

Xie, Xing; Bahnemann, Janina; Wang, Siwen; Yang, Yang; Hoffmann, Michael R.

2016-01-01

Detection and quantification of pathogens in water is critical for the protection of human health and for drinking water safety and security. When the pathogen concentrations are low, large sample volumes (several liters) are needed to achieve reliable quantitative results. However, most microbial identification methods utilize relatively small sample volumes. As a consequence, a concentration step is often required to detect pathogens in natural waters. Herein, we introduce a novel water sample concentration method based on superabsorbent polymer (SAP) beads. When SAP beads swell with water, small molecules can be sorbed within the beads, but larger particles are excluded and, thus, concentrated in the residual non-sorbed water. To illustrate this approach, millimeter-sized poly(acrylamide-co-itaconic acid) (P(AM-co-IA)) beads are synthesized and successfully applied to concentrate water samples containing two model microorganisms: Escherichia coli and bacteriophage MS2. Experimental results indicate that the size of the water channel within water swollen P(AM-co-IA) hydrogel beads is on the order of several nanometers. The millimeter size coupled with a negative surface charge of the beads are shown to be critical in order to achieve high levels of concentration. This new concentration procedure is very fast, effective, scalable, and low-cost with no need for complex instrumentation. PMID:26876979

Minimization of Residual Stress in an Al-Cu Alloy Forged Plate by Different Heat Treatments

Science.gov (United States)

Dong, Ya-Bo; Shao, Wen-Zhu; Jiang, Jian-Tang; Zhang, Bao-You; Zhen, Liang

2015-06-01

In order to improve the balance of mechanical properties and residual stress, various quenching and aging treatments were applied to Al-Cu alloy forged plate. Residual stresses determined by the x-ray diffraction method and slitting method were compared. The surface residual stress measured by x-ray diffraction method was consistent with that measured by slitting method. The residual stress distribution of samples quenched in water with different temperatures (20, 60, 80, and 100 °C) was measured, and the results showed that the boiling water quenching results in a 91.4% reduction in residual stress magnitudes compared with cold water quenching (20 °C), but the tensile properties of samples quenched in boiling water were unacceptably low. Quenching in 80 °C water results in 75% reduction of residual stress, and the reduction of yield strength is 12.7%. The residual stress and yield strength level are considerable for the dimensional stability of aluminum alloy. Quenching samples into 30% polyalkylene glycol quenchants produced 52.2% reduction in the maximum compressive residual stress, and the reduction in yield strength is 19.7%. Moreover, the effects of uphill quenching and thermal-cold cycling on the residual stress were also investigated. Uphill quenching and thermal-cold cycling produced approximately 25-40% reduction in residual stress, while the effect on tensile properties is quite slight.

Bacillus cereus as indicator in the sterilization of residual water with high energy electrons; Bacillus cereus como indicador en la desinfeccion de aguas residuales con electrones de alta energia

Energy Technology Data Exchange (ETDEWEB)

Mejia Z, E

2000-07-01

One of the main causes of water pollution is the presence of microorganisms that provoke infections, moreover of chemical substances. The processes of residual water treatment finally require of the disinfection for its use or final disposition. The radiation technology for the residual water treatment by mean of electron beams is an innovator process because as well as decomposing the chemical substance or to degrade them, also it provokes a disinfection by which this is proposed as alternative for disinfection of residual water, with the purpose in reusing the water treated in the agriculture, recreation and industry among others secondary activities, solving environmental or health problems. The objective of this work is to evaluate the use of Bacillus cereus as biological indicator in the disinfection by radiation, using High Energy Electrons. To fulfil with this objective, the work was developed in three stages, the first one consisted in the acquisition, propagation and conservation of the Bacillus cereus stumps, considering Escherichia coli and Salmonella typhimurium as pathogenic germs present in residual water. Moreover, the inocule standardization and the conditions of the Electron accelerator Type Pelletron. In the second stage it was performed the irradiation of aqueous samples of the microorganisms simulating biological pollution and the application to problem samples of a treatment plant sited in the Lerma River zone of mixed residual water. And in the third stage was performed a regression analysis to the reported survival for each kind of microorganisms. The results obtained show that with the use of Electron beams was reduced 6 logarithmic units de E. coli at 129 Gy, for S. typhimurium it was reduced 8 logarithmic units at 383 Gy and the B. cereus at 511 Gy was reduced 6.8 logarithmic units. Of the problem samples irradiated at 500 Gy, the concentration of the total account diminished from 8.70 x 10{sup 7} UFC/ml to 550 UFC/ml, the presence of B

Dielectric properties of residual water in amorphous lyophilized mixtures of sugar and drug

Energy Technology Data Exchange (ETDEWEB)

Moznine, R El [School of Pharmacy, De Montfort University, Leiceste (United Kingdom); Smith, G [School of Pharmacy, De Montfort University, Leicester (United Kingdom); Polygalov, E [School of Pharmacy, De Montfort University, Leicester (United Kingdom); Suherman, P M [School of Pharmacy, De Montfort University, Leicester (United Kingdom); Broadhead, J [AstraZeneca Charnwood R and D, Bakewell Rd, Loughborough (United Kingdom)

2003-02-21

Dielectric relaxation spectroscopy was used to investigate the properties of residual water in lyophilized formulations of a proprietary tri-phosphate drug containing a sugar (trehalose, lactose or sucrose) or dextran. The dielectric properties of each formulation were determined in the frequency range (0.1 Hz-0.1 MHz) and temperature range (30 deg. C-T{sub g}). The temperature dependence of the relaxation times for all samples showed Arrhenuis behaviour, from which the activation energy was derived. Proton hopping through the hydrogen-bonded network (clusters) of water molecules was suggested as the principle mode of charge transport. Significant differences in dielectric relaxation kinetics and activation energy were observed for the different formulations, which were found to correlate with the amount of monophosphate degradation product.

Multielement neutron activation analysis of underground water samples

International Nuclear Information System (INIS)

Kusaka, Yuzuru; Tsuji, Haruo; Fujimoto, Yuzo; Ishida, Keiko; Mamuro, Tetsuo.

1980-01-01

An instrumental neutron activation analysis by gamma-ray spectrometry with high resolution and large volume Ge (Li) detectors followed by data processing with an electronic computer was applied to the multielemental analysis to elucidate the chemical qualities of the underground water which has been widely used in the sake brewing industries in Mikage, Uozaki and Nishinomiya districts, called as miyamizu. The evaporated residues of the water samples were subjected to the neutron irradiations in reactor for 1 min at a thermal flux of 1.5 x 10 12 n.cm -2 .sec -1 and for 30 hrs at a thermal flux of 9.3 x 10 11 n.cm -2 .sec -1 or for 5 hrs at a thermal flux of 3.9 x 10 12 n.cm -2 .sec -1 . Thus, 11 elements in the former short irradiation and 38 elements in the latter two kinds of long irradiation can be analyzed. Conventional chemical analysis including atomic absorption method and others are also applied on the same samples, and putting the all results together, some considerations concerning the geochemical meaning of the analytical values are made. (author)

Assessing microbiological water quality in drinking water distribution systems with disinfectant residual using flow cytometry.

Science.gov (United States)

Gillespie, Simon; Lipphaus, Patrick; Green, James; Parsons, Simon; Weir, Paul; Juskowiak, Kes; Jefferson, Bruce; Jarvis, Peter; Nocker, Andreas

2014-11-15

Flow cytometry (FCM) as a diagnostic tool for enumeration and characterization of microorganisms is rapidly gaining popularity and is increasingly applied in the water industry. In this study we applied the method to obtain a better understanding of total and intact cell concentrations in three different drinking water distribution systems (one using chlorine and two using chloramines as secondary disinfectants). Chloramine tended to result in lower proportions of intact cells than chlorine over a wider residual range, in agreement with existing knowledge that chloramine suppresses regrowth more efficiently. For chlorinated systems, free chlorine concentrations above 0.5 mg L(-1) were found to be associated with relatively low proportions of intact cells, whereas lower disinfectant levels could result in substantially higher percentages of intact cells. The threshold for chlorinated systems is in good agreement with guidelines from the World Health Organization. The fact that the vast majority of samples failing the regulatory coliform standard also showed elevated proportions of intact cells suggests that this parameter might be useful for evaluating risk of failure. Another interesting parameter for judging the microbiological status of water, the biological regrowth potential, greatly varied among different finished waters providing potential help for investment decisions. For its measurement, a simple method was introduced that can easily be performed by water utilities with FCM capability. Copyright © 2014 Elsevier Ltd. All rights reserved.

Water leaching of titanium from ore flotation residue.

Science.gov (United States)

Jaworska, Malgorzata M; Guibal, Eric

2003-01-01

Copper ore tailings were tested for the stability of titanium submitted to water leaching in three different reactor systems (agitated vessel, bioreactor and percolated fixed-bed column). For each of these systems, titanium extraction did not exceed 1% of the available metal. Biomass removed from ore residue adsorbed a small part of the titanium with sorption capacities below 20-30 mg g(-1), but most of this biomass was sequestered in the ore residue. Oxygen and carbon dioxide concentrations were monitored and changes in concentration correlated with bacteria development at the initial stage of the process and to fungal development in the latter stages.

Chemical modelling of pore water composition from PFBC residues

International Nuclear Information System (INIS)

Karlsson, L.G.

1991-01-01

The concentration of trace elements varies depending on the source of the coal and also due to the combustion process used. Mercury is one important element among the trace elements in the coal residues, generally recognised as potentially harmful to the biological system. To predict the pore water concentrations of mercury and other important constituents leached from coal combustion residues disposal sites, mechanistic data on chemical reactions are required. The present study is an application of a basially thermodynamical approach using the geochemical code EQ3NR. The presence of discrete solid phases that control the aqueous concentrations of major elements such as aluminium, calcium and silicon are identified. Solid phases are modelled in equilibrium with a hypothetical pore water at a pH range of 7-11. In this study the thermodynamic database of EQ3NR has been complemented with data for cadmium, mercury and lead taken from the OECD/NEA Thermodynamic Database and from a compilation made by Lindsay. Possible solubility limiting phases for the important trace elements arsenic, cadmium, chromium, copper, mercury, nickel and lead have been identified. Concentrations of these trace elements as a function of pH in the hypothetical pore water were calculated using mechanistic thermodynamial data. The thermodynamical approach in this study seems justified because most solid residues that are either present or expected to form during weathering have relatively fast precipitation/dissolution kinetics. (21 refs., 18 figs., 5 tabs.)

Chemical modelling of trace elements in pore water from PFBC residues containing ammonia

International Nuclear Information System (INIS)

Karlsson, L.G.; Brandberg, F.

1993-01-01

Ammonia is added to the PFBC process with the purpose to reduce the emissions of NO x in the stack gases. The design of the system for cleaning the stack gases will lead to an increased adsorption of ammonia and an accumulation of soluble ammonium salts in the cyclone ash from PFBC processes. This can be an environmental problem since the amounts will increase over the coming years and there will be a need to dispose the residues. When infiltrating rainwater penetrates the disposed residues ammonia and ammonium salts result in a contamination of the pore water with ammonia in the disposed residues. This entail the solubility of several trace elements in the residues that form soluble complexes with ammonia will increase and cause an increased contamination of groundwater and surface water. In this study the increased solubilities is calculated for the trace elements cadmium, cobalt, copper, mercury, nickel, silver and zinc in the residues using thermodynamical data. The calculations have been performed with probable solid phases of the trace elements at oxidizing and reducing conditions as a function of pH and at varying concentration of ammonia in the pore water. The thermodynamic calculations have been performed with the geochemical code EQ3NR. The results from the calculations show that as a concentration of 17 mg NH 3 /l in the pore water of the residues increases the solubilities for copper and silver. If the concentration of ammonia increases to 170 mg NH 3 /l will the solubilities increase also for cadmium, nickel and zinc. (12 refs., 39 figs.)

A sensitive multi-residue method for the determination of 35 micropollutants including pharmaceuticals, iodinated contrast media and pesticides in water.

Science.gov (United States)

Valls-Cantenys, Carme; Scheurer, Marco; Iglesias, Mònica; Sacher, Frank; Brauch, Heinz-Jürgen; Salvadó, Victoria

2016-09-01

A sensitive, multi-residue method using solid-phase extraction followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) was developed to determine a representative group of 35 analytes, including corrosion inhibitors, pesticides and pharmaceuticals such as analgesic and anti-inflammatory drugs, five iodinated contrast media, β-blockers and some of their metabolites and transformation products in water samples. Few other methods are capable of determining such a broad range of contrast media together with other analytes. We studied the parameters affecting the extraction of the target analytes, including sorbent selection and extraction conditions, their chromatographic separation (mobile phase composition and column) and detection conditions using two ionisation sources: electrospray ionisation (ESI) and atmospheric pressure chemical ionisation (APCI). In order to correct matrix effects, a total of 20 surrogate/internal standards were used. ESI was found to have better sensitivity than APCI. Recoveries ranging from 79 to 134 % for tap water and 66 to 144 % for surface water were obtained. Intra-day precision, calculated as relative standard deviation, was below 34 % for tap water and below 21 % for surface water, groundwater and effluent wastewater. Method quantification limits (MQL) were in the low ng L(-1) range, except for the contrast agents iomeprol, amidotrizoic acid and iohexol (22, 25.5 and 17.9 ng L(-1), respectively). Finally, the method was applied to the analysis of 56 real water samples as part of the validation procedure. All of the compounds were detected in at least some of the water samples analysed. Graphical Abstract Multi-residue method for the determination of micropollutants including pharmaceuticals, iodinated contrast media and pesticides in waters by LC-MS/MS.

Mixing regime of the residual water basins of the Aral Sea

Science.gov (United States)

Izhitskiy, Alexander; Zavialov, Peter; Kirillin, Georgiy

2017-04-01

The Aral Sea, a terminal salt lake in western Central Asia situated at the border between Uzbekistan and Kazakhstan, was ranked as the fourth largest inland water body in the mid-20th century. However, in the early 1960s, the lake's volume started to decrease rapidly due to severe changes in the Aral's water balance. Thus, the present-day Aral Sea can be considered as a system of separate water bodies with a common origin but very different physical, chemical and biological features. Our previous studies showed that the Large Aral Sea and Lake Tshchebas transformed into hyperhaline water bodies, while the Small Aral Sea was a brackish basin with rather similar to the pre-desiccation environment. On the other hand, the Small Aral Sea and Lake Tshchebas exhibited a mixed vertical structure, whereas the Western Large Aral Sea (especially the Chernyshev Bay) was strongly stratified. The presented study is focused on the seasonal mixing regimes of the residual basins. Isolation of deep waters from the atmosphere together with low rates of photosynthesis produce deep anoxia observed in the Chernyshev Bay and in the Large Aral. The high amount of organic matter provides a rich source of nutrients for anoxic microorganisms favoring methanogenesis in the bottom layer of the basins. In the Small Aral, the water column remains well-oxygenated down to the bottom throughout most of the year and development of anoxia is unlikely. The mixing regimes of the recently formed residual lakes of the former Aral Sea will provide manifold effect on the ongoing development of the aquatic system in the following decades. The study is based on a field data collected during two surveys of Shirshov Institute of Oceanology to the Aral Sea, which took place in October, 2015 and June, 2016. In situ measurements including CTD profiling and water sampling were carried out in the northern extremity of the western Large Aral (the Chernyshev Bay), in Lake Tshchebas, and in the Small Aral Sea

Residual volume on land and when immersed in water: effect on percent body fat.

Science.gov (United States)

Demura, Shinichi; Yamaji, Shunsuke; Kitabayashi, Tamotsu

2006-08-01

There is a large residual volume (RV) error when assessing percent body fat by means of hydrostatic weighing. It has generally been measured before hydrostatic weighing. However, an individual's maximal exhalations on land and in the water may not be identical. The aims of this study were to compare residual volumes and vital capacities on land and when immersed to the neck in water, and to examine the influence of the measurement error on percent body fat. The participants were 20 healthy Japanese males and 20 healthy Japanese females. To assess the influence of the RV error on percent body fat in both conditions and to evaluate the cross-validity of the prediction equation, another 20 males and 20 females were measured using hydrostatic weighing. Residual volume was measured on land and in the water using a nitrogen wash-out technique based on an open-circuit approach. In water, residual volume was measured with the participant sitting on a chair while the whole body, except the head, was submerged . The trial-to-trial reliabilities of residual volume in both conditions were very good (intraclass correlation coefficient > 0.98). Although residual volume measured under the two conditions did not agree completely, they showed a high correlation (males: 0.880; females: 0.853; P body fat computed using residual volume measured in both conditions was very good for both sexes (males: r = 0.902; females: r = 0.869, P body fat: -3.4 to 2.2% for males; -6.3 to 4.4% for females). We conclude that if these errors are of no importance, residual volume measured on land can be used when assessing body composition.

Developing Water Sampling Standards

Science.gov (United States)

Environmental Science and Technology, 1974

1974-01-01

Participants in the D-19 symposium on aquatic sampling and measurement for water pollution assessment were informed that determining the extent of waste water stream pollution is not a cut and dry procedure. Topics discussed include field sampling, representative sampling from storm sewers, suggested sampler features and application of improved…

Gasification of fruit wastes and agro-food residues in supercritical water

International Nuclear Information System (INIS)

Nanda, Sonil; Isen, Jamie; Dalai, Ajay K.; Kozinski, Janusz A.

2016-01-01

Highlights: • Supercritical water gasification of various fruit wastes and agro-food residues. • Coconut shell had superior carbon content and calorific value due to high lignin. • Maximum H_2 yields at 600 °C with 1:10 biomass-to-water ratio, 45 min and 23–25 MPa. • High H_2 yields from coconut shell, bagasse and aloe vera rind with 2 wt% K_2CO_3. • High CH_4 yields from coconut shell with 2 wt% NaOH due to methanation reaction. - Abstract: Considerable amounts of fruit wastes and agro-food residues are generated worldwide as a result of food processing. Converting the bioactive components (e.g., carbohydrates, lipids, fats, cellulose, hemicellulose and lignin) in food wastes to biofuels is a potential remediation approach. This study highlights the characterization and hydrothermal conversion of several fruit wastes and agro-food residues such as aloe vera rind, banana peel, coconut shell, lemon peel, orange peel, pineapple peel and sugarcane bagasse to hydrogen-rich syngas through supercritical water gasification. The agro-food wastes were gasified in supercritical water to study the impacts of temperature (400–600 °C), biomass-to-water ratio (1:5 and 1:10) and reaction time (15–45 min) at a pressure range of 23–25 MPa. The catalytic effects of NaOH and K_2CO_3 were also investigated to maximize the hydrogen yields and selectivity. The elevated temperature (600 °C), longer reaction time (45 min) and lower feed concentration (1:10 biomass-to-water ratio) were optimal for higher hydrogen yield (0.91 mmol/g) and total gas yield (5.5 mmol/g) from orange peel. However, coconut shell with 2 wt% K_2CO_3 at 600 °C and 1:10 biomass-to-water ratio for 45 min revealed superior hydrogen yield (4.8 mmol/g), hydrogen selectivity (45.8%) and total gas yield (15 mmol/g) with enhanced lower heating value of the gas product (1595 kJ/Nm"3). The overall findings suggest that supercritical water gasification of fruit wastes and agro-food residues could serve as

Sources of manganese in the residue from a water treatment plant ...

African Journals Online (AJOL)

Disposal of water treatment residue (WTR), the by-product from the production of potable water, has traditionally been to landfill. The shortage of suitable landfill sites has led to the proposal that WTR be applied to land. Such disposal is only possible if the WTR contains no toxic elements that may contaminate soil, water or ...

Characterization of biomass residues and their amendment effects on water sorption and nutrient leaching in sandy soil.

Science.gov (United States)

Wang, Letian; Tong, Zhaohui; Liu, Guodong; Li, Yuncong

2014-07-01

In this study, we evaluated the efficiency of two types of biomass residues (fermentation residues from a bioethanol process, FB; brown mill residues from a papermaking process, BM) as amendments for a sandy soil. The characteristics of these residues including specific surface areas, morphologies and nutrient sorption capacity were measured. The effects of biorefinery residues on water and nutrient retention were investigated in terms of different particle sizes and loadings. The results indicated that bio-based wastes FB and BM were able to significantly improve water and nutrient retention of sandy soil. The residues with larger surface areas had better water and nutrient retention capability. Specifically, in the addition of 10% loading, FB and BM was able to improve water retention by approximately 150% and 300%, while reduce 99% of ammonium and phosphate concentration in the leachate compare to the soil control, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

Solid Phase Microextraction (SPME in Determination of Pesticide Residues in Soil Samples

Directory of Open Access Journals (Sweden)

Rada Đurović

2011-01-01

Full Text Available The basic principles and application possibilities of the methods based on solid phase microextraction (SPME in the analysis of pesticide residues in soil samples are presented in the paper. The most important experimental parameters which affect SPME efficacy inpesticide determination (type and thickness of microextraction fiber, duration of microextraction,temperature at which it is conducted, effect of addition of salts (the effect of efflorescence,temperature and time of desorption, the choice of optimal solvent for pesticide exctraction from the soil and the optimal number of extraction steps, as well as general guidelines for their optimization are also shown. In the end, current applications of SPMEmethods in the analysis of pesticide residues in soil samples are presented.

Pesticide Residues in Commercial Lettuce, Onion, and Potato Samples From Bolivia—A Threat to Public Health?

DEFF Research Database (Denmark)

Skovgaard, Marlene; Renjel, Susana; Jensen, Olaf Chresten

2017-01-01

lettuce samples from La Paz were sampled on August 15, 2015 at a local market and screened for 283 pesticides. Residues of cypermethrin, chlorpyrifos, difenoconazol, or/and λ-cyhalothrin were detected in 50% of the lettuce samples, whereas no pesticides were found in potatoes and onions. In 20......% of the lettuce samples, the measurements were above the maximum residue limits, and 2 or 3 pesticides were identified simultaneously. Washing almost halved the pesticide levels, but still 20% of the samples showed measurements above the limits. No samples contained concentrations of pesticides which alone...

Derivation of residual radioactive material guidelines for uranium in soil at the Middlesex Sampling Plant Site, Middlesex, New Jersey

International Nuclear Information System (INIS)

Dunning, D.E.

1995-02-01

Residual radioactive material guidelines for uranium in soil were derived for the Middlesex Sampling Plant (MSP) site in Middlesex, New Jersey. This site has been designated for remedial action under the Formerly Utilized Sites Remedial Action Program (FUSRAP) of the US Department of Energy. The site became contaminated from operations conducted in support of the Manhattan Engineer District (MED) and the Atomic Energy Commission (AEC) between 1943 and 1967. Activities conducted at the site included sampling, storage, and shipment of uranium, thorium, and beryllium ores and residues. Uranium guidelines for single radioisotopes and total uranium were derived on the basis of the requirement that the 50-year committed effective dose equivalent to a hypothetical individual living or working in the immediate vicinity of the MSP site should not exceed a dose of 30 mrem/yr following remedial action for the current-use and likely future-use scenarios or a dose of 100 mrem/yr for less likely future-use scenarios. The RESRAD computer code, which implements the methodology described in the DOE manual for establishing residual radioactive material guidelines, was used in this evaluation. Four scenarios were considered for the site. These scenarios vary regarding future land use at the site, sources of water used, and sources of food consumed

Effects of fretting fatigue on the residual stress of shot peened Ti-6Al-4V samples

International Nuclear Information System (INIS)

Martinez, S.A.; Sathish, S.; Blodgett, M.P.; Mall, S.; Namjoshi, S.

2005-01-01

X-ray diffraction residual stress measurement has been utilized as nondestructive tool for the characterization of fretting fatigue damage in shot peened samples of Ti-6Al-4V. Prior to fretting fatigue damage, compressive residual stresses were found to be uniform over the entire face of the sample and independent of the measurement direction. After fretting fatigue, inside and in the vicinity of the fretting damage zone large relaxation of compressive residual stress was observed. An anisotropic residual stress distribution has been observed in the fretting fatigue damaged region. Residual stress measurements in interrupted fretting fatigue experiments showed that the relaxation of residual stress increases as the number of fretting fatigue cycles increase. The results are discussed in the light of their importance in establishing X-ray diffraction residual stress measurement technique as a nondestructive tool to characterize fretting fatigue damage

Treatment of mine water and solid residues (RS) in San Rafael mining and milling complex

International Nuclear Information System (INIS)

Asenjo, Armando R.; Perrino, Juan F.

2006-01-01

San Rafael Mining and Milling Complex is located in Mendoza Province, in San Rafael Department, 38 km West from San Rafael city and 240 km south from Mendoza city, capital of the province. Activities related with yellow cake production were performed from 1979 to 1999. Nowadays the mine and the plant are in stand by. At the moment technical, economic and environmental studies are being done in order to restart the activities. Different kind of residues are accumulated in the site: a) Tailing; b) Sludges; c) Low grade ores; e) Waste rock; f) Mine water; g) Solid residues (RS). In this paper methodology to treat mine water and solid residues (RS) will be informed. a) Mine water: 800.000 m 3 of mine water are accumulated in different open pit. Uranium, radium and arsenic are the main ions to take into account to treat the water. Several laboratory and pilot test have been performed in order to define the treatment of the water, according with the regulatory requirement. A methodology using anion exchange resin to fix uranium and precipitation using barium chloride and iron sulfate to separate radium and arsenic has been developed. b) Solid residues (RS): these residues (precipitates) have been produced by neutralization of effluents in a nuclear purification process (TBP process). They are accumulated in drums. These residues come from Cordoba plant, a factory which produces UO 2 powder. The total content of uranium in the precipitate is 14.249 kg with an average uranium concentration of 1,33%. A methodology using sulfuric acid dissolution of the precipitates and anion exchange resin to recovery the uranium has been developed. (author) [es

Determination of selected pesticides in water samples adjacent to agricultural fields and removal of organophosphorus insecticide chlorpyrifos using soil bacterial isolates

Science.gov (United States)

Hossain, M. S.; Chowdhury, M. Alamgir Zaman; Pramanik, Md. Kamruzzaman; Rahman, M. A.; Fakhruddin, A. N. M.; Alam, M. Khorshed

2015-06-01

The use of pesticide for crops leads to serious environmental pollution, therefore, it is essential to monitor and develop approaches to remove pesticide from contaminated environment. In this study, water samples were collected to monitor pesticide residues, and degradation of chlorpyrifos was also performed using soil bacteria. Identification of pesticide residues and determination of their levels were performed by high-performance liquid chromatography with photodiode array detector. Among 12 samples, 10 samples were found contaminated with pesticides. Chlorpyrifos was detected in four tested samples and concentrations ranged from 3.27 to 9.31 μg/l whereas fenitrothion ranging from (Below Detection Limit, chlorpyrifos completely in 8, 10 and 10 days, respectively, when 20 mg/l chlorpyrifos was supplied as sole source of carbon. Whereas, BG1, BG4 and PD6 took 14, 16 and 16 days, respectively, for complete removal of 50 mg/l chlorpyrifos. Chlorpyrifos degradation rates were found maximum by all three isolates at 2nd day of incubation for both tested concentrations. The results of the present study suggest the need for regular monitoring of pesticide residues in water, to protect the aquatic environment. Chlorpyrifos degrading bacterial isolates can be used to clean up environmental samples contaminated with the organophosphate pesticides.

Residual fluxes of water, salt and suspended sediment in the Beypore Estuary

Digital Repository Service at National Institute of Oceanography (India)

AnilKumar, N.; Revichandran, C.; Sankaranarayanan, V.N.; Josanto, V.

The monthly trends of the residual fluxes of salt and water and the transportation of suspended sediments in the Beypore estuarine system, Kerala, India were examined. At the river mouth the water flux was directed seaward during the postmonsoon...

POPULATION DIVERSITY IN MODEL DRINKING WATER BIOFILMS RECEIVING CHLORINE OR MONOCHLORAMINE RESIDUAL

Science.gov (United States)

Most water utilities add monochloramine or chlorine as a residual disinfectant in potable water distribution systems (WDS) to control bacterial regrowth. While monochloramine is considered more stable than chlorine, little is known about the fate of this disinfectant or the effec...

Stabilization of arsenic and chromium polluted soils using water treatment residues

DEFF Research Database (Denmark)

Nielsen, Sanne Skov

water and can be used as a soil amendment to decrease the mobility of CCA in contaminated soil. Stabilization with Fe-WTR was tested at the Collstrop site in Hillerød, Denmark. The site has been polluted with a wide range of wood impregnation agents including CCA during 40 years of wood impregnating...... of contaminants. Arsenic, chromium and copper cannot be degraded and existing methods for cleaning the soil are rarely used as they are expensive and technically demanding. Chemical stabilization of polluted soil is an alternative method for soil remediation, especially metal contamination, and consists in adding...... or other sorbents. Iron water treatment residues mainly consist of ferrihydrite, an oxidized iron oxy-hydroxide with a high reactivity and a large specific surface area with a high capacity for adsorption. Iron water treatment residues (Fe-WTR) are a by-product from treatment of groundwater to drinking...

Assessment of Residual Stresses in 3013 Inner and Outer Containers and Teardrop Samples

Energy Technology Data Exchange (ETDEWEB)

Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Prime, Michael Bruce [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Clausen, Bjorn [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); DeWald, Adrian T. [Hill Engineering, LLC, Rancho Cordova, CA (United States)

2015-12-08

This report is an assessment performed by LANL that examines packaging for plutonium-bearing materials and the resilience of its design. This report discusses residual stresses in the 3013 outer, the SRS/Hanford and RFETS/LLNL inner containers, and teardrop samples used in studies to assess the potential for SCC in 3013 containers. Residual tensile stresses in the heat affected zones of the closure welds are of particular concern.

Assessment of Residual Stresses in 3013 Inner and Outer Containers and Teardrop Samples

International Nuclear Information System (INIS)

Stroud, Mary Ann; Prime, Michael Bruce; Veirs, Douglas Kirk; Berg, John M.; Clausen, Bjorn; Worl, Laura Ann; DeWald, Adrian T.

2015-01-01

This report is an assessment performed by LANL that examines packaging for plutonium-bearing materials and the resilience of its design. This report discusses residual stresses in the 3013 outer, the SRS/Hanford and RFETS/LLNL inner containers, and teardrop samples used in studies to assess the potential for SCC in 3013 containers. Residual tensile stresses in the heat affected zones of the closure welds are of particular concern.

Detection by PCR of pathogenic protozoa in raw and drinkable water samples in Colombia.

Science.gov (United States)

Triviño-Valencia, Jessica; Lora, Fabiana; Zuluaga, Juan David; Gomez-Marin, Jorge E

2016-05-01

We evaluated the presence of DNA of Giardia, Toxoplasma, and Cryptosporidium by PCR, and of Giardia and Cryptosporidium genera by immunofluorescence antibody test (IFAT), in water samples, before, during, and after plant treatment for drinkable water. We applied this method in 38 samples of 10 l of water taken from each of the water treatment steps and in 8 samples taken at home (only for Toxoplasma PCR) in Quindio region in Colombia. There were 8 positive samples for Cryptosporidium parvum (21 %), 4 for Cryptosporidium hominis (10.5 %), 27 for Toxoplasma gondii (58.6 %), 2 for Giardia duodenalis assemblage A (5.2 %), and 5 for G. duodenalis assemblage B (13.1 %). By IFAT, 23 % were positive for Giardia and 21 % for Cryptosporidium. An almost perfect agreement was found between IFAT and combined results of PCR, by Kappa composite proportion analysis. PCR positive samples were significantly more frequent in untreated raw water for C. parvum (p = 0.02). High mean of fecal coliforms, high pH values, and low mean of chlorine residuals were strongly correlated with PCR positivity for G. duodenalis assemblage B. High pH value was correlated with PCR positivity for C. parvum. Phylogenetic analysis of DNA sequences was possible, showing water and human clinical sequences for Toxoplasma within the same phylogenetic group for B1 repeated sequence. PCR assay is complementary to IFAT assay for monitoring of protozoa in raw and drinkable water, enabling species identification and to look for phylogenetic analysis in protozoa from human and environmental sources.

Study of Organochlorinated Pesticide Residues and Polychlorinated Biphenyls in Soil Samples

Directory of Open Access Journals (Sweden)

MSc. Vlora Gashi

2013-12-01

Full Text Available This paper presents and discusses the data obtained for organochlorinated pesticides and their residues in the soil samples of agricultural areas. Soil contamination is one of most important factors influencing the quality of agricultural products. Usage of heavy farm equipment, the land drainage, an exces­sive application of agrochemicals, emissions originating from mining, metallurgical, and chemical and coal power plants and transport, all generate a number of undesired substances (nitric and sulphur oxides, PAHs, heavy metals, pesticides, which after deposition in soil may influence crop quality. Thus, input of these contaminants into the environment should be carefully monitored. Levels of organochlorinated pesticides contamination were evaluated in agriculture areas that are in use. 10 soil samples were taken in agricultural areas  Plane of  Dugagjini , Kosovo. Representa­tive soil samples were collected from 0-30 cm top layer of the soil. In the analytical method we combined ultrasonic bath extraction and a Florisil column for samples clean-up. The analysis of the organochlorinated pesticides in soil samples was performed by gas chromatography technique using electron capture detector (GC/ECD. Optima-5 (low/mid polarity, 5% phenyl methyl siloxane 60 m x 0.33 mm x 0.25μm film capillary column was used for isolation and determination of organochlorinated pesticides. Low concentrations of organochlorinated pesticide and their metabolites were found in the studied samples. The presence of organochlorinated pesticides and their residues is probably resulting of their previous uses for agricultural purposes.

Remediation of cadmium contaminated water and soil using vinegar residue biochar.

Science.gov (United States)

Li, Yuxin; Pei, Guangpeng; Qiao, Xianliang; Zhu, Yuen; Li, Hua

2018-06-01

This study investigated a new biochar produced from vinegar residue that could be used to remediate cadmium (Cd)-contaminated water and soil. Aqueous solution adsorption and soil incubation experiments were performed to investigate whether a biochar prepared at 700 °C from vinegar residue could efficiently adsorb and/or stabilize Cd in water and soil. In the aqueous solution adsorption experiment, the Cd adsorption process was best fitted by the pseudo-second-order kinetic and Freundlich isotherm models. If the optimum parameters were used, i.e., pH 5 or higher, a biochar dosage of 12 g L -1 , a 10 mg L -1 Cd initial concentration, and 15-min equilibrium time, at 25 °C, then Cd removal could reach about 100%. The soil incubation experiment evaluated the biochar effects at four different application rates (1, 2, 5, and 10% w/w) and three Cd contamination rates (0.5, 1, and 2.5 mg kg -1 ) on soil properties and Cd fractionation. Soil pH and organic matter increased after adding biochar, especially at the 10% application rate. At Cd pollution levels of 1.0 or 2.5 mg kg -1 , a 10% biochar application rate was most effective. At 0.5 mg Cd kg -1 soil, a 5% biochar application rate was most efficient at transforming the acid extractable and easily reducible Cd fractions to oxidizable and residual Cd. The results from this study demonstrated that biochar made from vinegar residue could be a new and promising alternative biomass-derived material for Cd remediation in water and soil.

Adaptive Kalman Filter Based on Adjustable Sampling Interval in Burst Detection for Water Distribution System

Directory of Open Access Journals (Sweden)

Doo Yong Choi

2016-04-01

Full Text Available Rapid detection of bursts and leaks in water distribution systems (WDSs can reduce the social and economic costs incurred through direct loss of water into the ground, additional energy demand for water supply, and service interruptions. Many real-time burst detection models have been developed in accordance with the use of supervisory control and data acquisition (SCADA systems and the establishment of district meter areas (DMAs. Nonetheless, no consideration has been given to how frequently a flow meter measures and transmits data for predicting breaks and leaks in pipes. This paper analyzes the effect of sampling interval when an adaptive Kalman filter is used for detecting bursts in a WDS. A new sampling algorithm is presented that adjusts the sampling interval depending on the normalized residuals of flow after filtering. The proposed algorithm is applied to a virtual sinusoidal flow curve and real DMA flow data obtained from Jeongeup city in South Korea. The simulation results prove that the self-adjusting algorithm for determining the sampling interval is efficient and maintains reasonable accuracy in burst detection. The proposed sampling method has a significant potential for water utilities to build and operate real-time DMA monitoring systems combined with smart customer metering systems.

Measurement of residual stresses in welded sample of dissimilar materials

International Nuclear Information System (INIS)

Mansur, Tanius Rodrigues; Gomes, Paulo de Tarso Vida; Scaldaferri, Denis Henrique Bianchi; Martins, Geraldo Antonio Scoralick; Atanazio Filho, Nelson do Nascimento

2008-01-01

reactors, what can generate significant residual stresses due so much to the welding procedure as for the difference of the coefficients of thermal expansion of the involved materials. In this work, are shown the results of the measurement of residual tensions in welded sample of steel carbon SA 508 Cl 3 and stainless steel 316L. The Inconel 182 was used as weld metal. (author)

pesticide residues in water from tpc sugarcane plantations

African Journals Online (AJOL)

ABSTRACT. We report herein, the analysis of water samples collected from TPC Sugarcane Plantation and its environs in Kilimanjaro region, which is the earliest intensive user of pesticides in Tanzania. A total of 50 water samples collected from 18 sampling sites between 2000 and 2001 were analyzed for pesticide ...

Water born pollutants sampling using porous suction samples

International Nuclear Information System (INIS)

Baig, M.A.

1997-01-01

The common standard method of sampling water born pollutants in the vadoze zone is core sampling and it is followed by extraction of pore fluid. This method does not allow sampling at the same location next time and again later on. There is an alternative approach for sampling fluids (water born pollutants) from both saturated and unsaturated regions of vadose zone using porous suction samplers. There are three types of porous suction samplers, vacuum-operated, pressure-vacuum lysimeters, high pressure vacuum samples. The suction samples are operated in the range of 0-70 centi bars and usually consist of ceramic and polytetrafluorethylene (PTFE). The operation range of PTFE is higher than ceramic cups. These samplers are well suited for in situ and repeated sampling form the same location. This paper discusses the physical properties and operating condition of such samplers to the utilized under our environmental sampling. (author)

Influence of organic waste and residue mud additions on chemical, physical and microbial properties of bauxite residue sand.

Science.gov (United States)

Jones, Benjamin E H; Haynes, Richard J; Phillips, Ian R

2011-02-01

In an alumina refinery, bauxite ore is treated with sodium hydroxide at high temperatures and pressures and for every tone of alumina produced, about 2 tones of alkaline, saline bauxite processing waste is also produced. At Alcoa, a dry stacking system of disposal is used, and it is the sand fraction of the processing waste that is rehabilitated. There is little information available regarding the most appropriate amendments to add to the processing sand to aid in revegetation. The purpose of this study was to investigate how the addition of organic wastes (biosolids and poultry manure), in the presence or absence of added residue mud, would affect the properties of the residue sand and its suitability for revegetation. Samples of freshly deposited residue sand were collected from Alcoa's Kwinana refinery. Samples were treated with phosphogypsum (2% v/v), incubated, and leached. A laboratory experiment was then set up in which the two organic wastes were applied at 0 or the equivalent to 60 tones ha(-1) in combination with residue mud added at rates of 0%, 10% and 20% v/v. Samples were incubated for 8 weeks, after which, key chemical, physical and microbial properties of the residue sand were measured along with seed germination. Additions of residue mud increased exchangeable Na(+), ESP and the pH, and HCO (3) (-) and Na(+) concentrations in saturation paste extracts. Additions of biosolids and poultry manure increased concentrations of extractable P, NH (4) (+) , K, Mg, Cu, Zn, Mn and Fe. Addition of residue mud, in combination with organic wastes, caused a marked decrease in macroporosity and a concomitant increase in mesoporosity, available water holding capacity and the quantity of water held at field capacity. With increasing residue mud additions, the percentage of sample present as sand particles (2 mm diameter) increased; greatest aggregation occurred where a combination of residue mud and poultry manure were added. Stability of aggregates, as measured by

An overview of the main foodstuff sample preparation technologies for tetracycline residue determination.

Science.gov (United States)

Pérez-Rodríguez, Michael; Pellerano, Roberto Gerardo; Pezza, Leonardo; Pezza, Helena Redigolo

2018-05-15

Tetracyclines are widely used for both the treatment and prevention of diseases in animals as well as for the promotion of rapid animal growth and weight gain. This practice may result in trace amounts of these drugs in products of animal origin, such as milk and eggs, posing serious risks to human health. The presence of tetracycline residues in foods can lead to the transmission of antibiotic-resistant pathogenic bacteria through the food chain. In order to ensure food safety and avoid exposure to these substances, national and international regulatory agencies have established tolerance levels for authorized veterinary drugs, including tetracycline antimicrobials. In view of that, numerous sensitive and specific methods have been developed for the quantification of these compounds in different food matrices. One will note, however, that the determination of trace residues in foods such as milk and eggs often requires extensive sample extraction and preparation prior to conducting instrumental analysis. Sample pretreatment is usually the most complicated step in the analytical process and covers both cleaning and pre-concentration. Optimal sample preparation can reduce analysis time and sources of error, enhance sensitivity, apart from enabling unequivocal identification, confirmation and quantification of target analytes. The development and implementation of more environmentally friendly analytical procedures, which involve the use of less hazardous solvents and smaller sample sizes compared to traditional methods, is a rapidly increasing trend in analytical chemistry. This review seeks to provide an updated overview of the main trends in sample preparation for the determination of tetracycline residues in foodstuffs. The applicability of several extraction and clean-up techniques employed in the analysis of foodstuffs, especially milk and egg samples, is also thoroughly discussed. Copyright © 2018 Elsevier B.V. All rights reserved.

Treatment of drinking water residuals: comparing sedimentation and dissolved air flotation performance with optimal cation ratios.

Science.gov (United States)

Bourgeois, J C; Walsh, M E; Gagnon, G A

2004-03-01

Spent filter backwash water (SFBW) and clarifier sludge generally comprise the majority of the waste residual volume generated and in relative terms, these can be collectively referred to as combined filter backwash water (CFBW). CFBW is essentially a low-solids wastewater with metal hydroxide flocs that are typically light and slow to settle. This study evaluates the impact of adding calcium and magnesium carbonates to CFBW in terms of assessing the impacts on the sedimentation and DAF separation processes. Representative CFBW samples were collected from two surface water treatment plants (WTP): Lake Major WTP (Dartmouth, Nova Scotia, Canada) and Victoria Park WTP (Truro, Nova Scotia, Canada). Bench-scale results indicated that improvements in the CFBW settled water quality could be achieved through the addition of the divalent cations, thereby adjusting the monovalent to divalent (M:D) ratios of the wastewater. In general, the DAF process required slightly higher M:D ratios than the sedimentation process. The optimum M:D ratios for DAF and sedimentation were determined to be 1:1 and 0.33:1, respectively. It was concluded that the optimisation of the cation balance between monovalent cations (e.g., Na(+), K(+)) and added divalent cations (i.e., Ca(2+), Mg(2+)) aided in the settling mechanism through charge neutralisation-precipitation. The increase in divalent cation concentrations within the waste residual stream promoted destabilisation of the negatively charged colour molecules within the CFBW, thereby causing the colloidal content to become more hydrophobic.

Evaluating organochlorine pesticide residues in the aquatic environment of the Lake Naivasha River basin using passive sampling techniques.

Science.gov (United States)

Abbasi, Yasser; Mannaerts, Chris M

2018-05-18

Passive sampling techniques can improve the discovery of low concentrations by continuous collecting the contaminants, which usually go undetected with classic and once-off time-point grab sampling. The aim of this study was to evaluate organochlorine pesticide (OCP) residues in the aquatic environment of the Lake Naivasha river basin (Kenya) using passive sampling techniques. Silicone rubber sheet and Speedisk samplers were used to detect residues of α-HCH, β-HCH, γ-HCH, δ-HCH, heptachlor, aldrin, heptachlor epoxide, pp-DDE, endrin, dieldrin, α-endosulfan, β-endosulfan, pp-DDD, endrin aldehyde, pp-DDT, endosulfan sulfate, and methoxychlor in the Malewa River and Lake Naivasha. After solvent extraction from the sampling media, the residues were analyzed using gas chromatography electron capture detection (GC-ECD) for the OCPs and gas chromatography-mass spectrometry (GC-MS) for the PCB reference compounds. Measuring the OCP residues using the silicone rubber samplers revealed the highest concentration of residues (∑OCPs of 81 (± 18.9 SD) μg/L) to be at the Lake site, being the ultimate accumulation environment for surficial hydrological, chemical, and sediment transport through the river basin. The total OCP residue sums changed to 71.5 (± 11.3 SD) μg/L for the Middle Malewa and 59 (± 12.5 SD) μg/L for the Upper Malewa River sampling sites. The concentration sums of OCPs detected using the Speedisk samplers at the Upper Malewa, Middle Malewa, and the Lake Naivasha sites were 28.2 (± 4.2 SD), 31.3 (± 1.8 SD), and 34.2 (± 6.4 SD) μg/L, respectively. An evaluation of the different pesticide compound variations identified at the three sites revealed that endosulfan sulfate, α-HCH, methoxychlor, and endrin aldehyde residues were still found at all sampling sites. However, the statistical analysis of one-way ANOVA for testing the differences of ∑OCPs between the sampling sites for both the silicone rubber sheet and Speedisk samplers

A Comparison of Soil-Water Sampling Techniques

Science.gov (United States)

Tindall, J. A.; Figueroa-Johnson, M.; Friedel, M. J.

2007-12-01

The representativeness of soil pore water extracted by suction lysimeters in ground-water monitoring studies is a problem that often confounds interpretation of measured data. Current soil water sampling techniques cannot identify the soil volume from which a pore water sample is extracted, neither macroscopic, microscopic, or preferential flowpath. This research was undertaken to compare values of extracted suction lysimeters samples from intact soil cores with samples obtained by the direct extraction methods to determine what portion of soil pore water is sampled by each method. Intact soil cores (30 centimeter (cm) diameter by 40 cm height) were extracted from two different sites - a sandy soil near Altamonte Springs, Florida and a clayey soil near Centralia in Boone County, Missouri. Isotopically labeled water (O18? - analyzed by mass spectrometry) and bromide concentrations (KBr- - measured using ion chromatography) from water samples taken by suction lysimeters was compared with samples obtained by direct extraction methods of centrifugation and azeotropic distillation. Water samples collected by direct extraction were about 0.25 ? more negative (depleted) than that collected by suction lysimeter values from a sandy soil and about 2-7 ? more negative from a well structured clayey soil. Results indicate that the majority of soil water in well-structured soil is strongly bound to soil grain surfaces and is not easily sampled by suction lysimeters. In cases where a sufficient volume of water has passed through the soil profile and displaced previous pore water, suction lysimeters will collect a representative sample of soil pore water from the sampled depth interval. It is suggested that for stable isotope studies monitoring precipitation and soil water, suction lysimeter should be installed at shallow depths (10 cm). Samples should also be coordinated with precipitation events. The data also indicate that each extraction method be use to sample a different

Combining physico-chemical analysis with a Daphnia magna bioassay to evaluate a recycling technology for drinking water treatment plant waste residuals.

Science.gov (United States)

Chen, Ting; Xu, Yongpeng; Zhu, Shijun; Cui, Fuyi

2015-12-01

Recycling water treatment plant (WTP) waste residuals is considered to be a feasible method to enhance the efficiency of pollutant removal. This study also evaluated the safety and water quality of a pilot-DWTP waste residuals recycling technology by combining physical-chemistry analysis with a Daphnia magna assay. The water samples taken from each treatment step were extracted and concentrated by XAD-2 resin and were then analyzed for immobilization and enzyme activity with D. magna. The measured parameters, such as the dissolve organic carbon (DOC), UV254 and THM formation potential (THMFPs) of the recycling process, did not obviously increase over 15 days of continuous operation and were even lower than typical values from a conventional process. The extract concentration ranged from 0 to 2 Leq/ml as measured on the 7th and 15th days and the immobilization of D. magna exposed to water treated by the recycling process was nearly equivalent to that of the conventional process. Both the superoxide dismutase (SOD) and the catalase (CAT) activity assay indicated that a lower dose of water extract (0.5, 1, 1.5 Leq/ml) could stimulate the enzyme activity of D. magna, whereas a higher dose (2 Leq/ml at the sampling point C3, R3, R4 ) inhibits the activity. Moreover, the SOD and CAT activity of D. magna with DOC and UV254 showed a strong concentration-effect relationship, where the concentration range of DOC and UV254 were 4.1-16.2 mg/L and 0.071-4.382 cm(-1), respectively. The results showed that there was no statistically significant difference (p>0.05) between the conventional and recycling treatment processes and the toxicity of water samples in the recycling process did not increase during the 15-day continuous recycling trial. Copyright © 2015 Elsevier Inc. All rights reserved.

Investigative studies on water contamination in Bangladesh. Primary treatment of water samples at the sampling site

International Nuclear Information System (INIS)

Sera, K.; Islam, Md. Shafiqul; Takatsuji, T.; Nakamura, T.; Goto, S.; Takahashi, C.; Saitoh, Y.

2010-01-01

Arsenic concentration in 13 well waters, 9 pond waters, 10 agricultural waters and a coconut juice taken in Comilla district, Bangladesh, where the problem of arsenic pollution is the most severe, was investigated. High-level arsenic is detected even in the well water which has been kept drinking by the people. Relatively high arsenic concentration was detected for some pond and farm waters even though the sampling was performed just after the rainy season and the waters were expected to be highly diluted. Clear relationship was observed in elemental compositions between the pond water and the coconut juice collected at the edge of the water. These results are expected to become the basic information for evaluating the risk of individual food such as cultured fishes, shrimps and farm products, and for controlling total intakes of arsenic. In order to solve the problem of transportation of water samples internationally, a simple method of target preparation performed at the sampling site was established and its validity was confirmed. All targets were prepared at the sampling sites in this study on the basis of this method. (author)

Measurements of three dimensional residual stress distribution on laser irradiated spot

International Nuclear Information System (INIS)

Tanaka, Hirotomo; Akita, Koichi; Ohya, Shin-ichi; Sano, Yuji; Naito, Hideki

2004-01-01

Three dimensional residual stress distributions on laser irradiated spots were measured using synchrotron radiation to study the basic mechanism of laser peening. A water-immersed sample of high tensile strength steel was irradiated with Q-switched and frequency-doubled Nd:YAG laser. The residual stress depth profile of the sample was obtained by alternately repeating the measurement and surface layer removal by electrolytic polishing. Tensile residual stresses were observed on the surface of all irradiated spots, whereas residual stress changed to compressive just beneath the surface. The depth of compressive residual stress imparted by laser irradiation and plastic deformation zone increased with increasing the number of laser pulses irradiated on the same spot. (author)

Impacts of climate-induced changes on the distribution of pesticides residues in water and sediment of Lake Naivasha, Kenya.

Science.gov (United States)

Otieno, Peter O; Owuor, P Okinda; Lalah, Joseph O; Pfister, Gerd; Schramm, Karl-Werner

2013-03-01

This study reports evidence of increased chlorpyrifos contamination in sediment and water in Lake Naivasha following its intensive application in the horticultural farms in the catchment area. Analytical results show that levels of chlorpyrifos residues were influenced by climate-induced rainfall pattern with higher levels reported during period of heavy precipitation with significant decrease during low rainfall. On average, the levels ranged between 14.8 and 32.8 ng g(-1) in sediment during rainy season compared to a range of 8.5-16.6 ng g(-1) in the dry season. Additionally, the mean concentration of chlorpyrifos in water ranged between 8.61 and 22.4 μg L(-1) during rainy season and below detection limit (bdl) -13.6 μg L(-1) in dry season as quantified by enzyme-linked immunosorbent assay. Meanwhile, independent t test analysis indicated that there was significant difference in concentration at p ≤ 0.05 between the seasons with respect to sediment and water samples. This demonstrated that climate-induced variations had considerable influence on contamination. While diazinon and carbofuran were equally applied intensively, their levels were below the detection limit in the all the samples analyzed. ELISA results were validated by the capillary-HPLC photodiode-array detector instrument analysis, and statistical comparison showed no significant difference between them. It was evident that chlorpyrifos residues determination in water and sediment by ELISA can be a useful strategy in environmental management and monitoring program, and a complimentary analytical tool to high performance liquid chromatography. Levels of chlorpyrifos detected in sediment and water were found to exceed recommended criteria for protection of aquatic life and preservation of water quality and may be hazardous if not regularly monitored.

The use of dispersive X-ray fluorescence technique for pollution evaluation of heavy metals in water samples and lake sediments

International Nuclear Information System (INIS)

Vives, Ana Elisa Sirito de; Brienza, Sandra Maria Boscolo

2002-01-01

The energy dispersive X-ray fluorescence technique (EDXRF) was used to determine metals concentration in water and bottom sediments samples in lakes at Santa Gertrudes region, Sao Paulo state, Brazil. The studied area is about 12 ha, with several lakes formed by argil extraction and present high volume of waste which can be dangerous and cause risks to water flora and fauna and also to human health by direct or indirect contact with the residues. To evaluate contamination degree by heavy metals water samples were collected in three lakes, in 2000 July and November, corresponding to the dry and rainy season. In two lakes the sampling procedure were superficial, and in the third lake, sampling was done at central region and in different deepness. Sediment samples were collected at two lakes, in 2000, July (dry) and November (rainy). To determine biologically available metals concentration (no-residual fraction) in the sediment, an acid extraction procedure was used. To quantitative analysis of both samples, metals were pre concentrated by complexation with ammonium pyrrolidine dithiocarbamate. Samples were excited with a X-ray tube with Mo target and Zr filter, operated at 25 kV/10 mA, and X-ray characteristics measure were done with a Si(Li) semi conductor detector. In water samples, were determined the elements Fe, Cu, Zn and Pb. Among the analyzed elements, Fe presented the highest concentration, independent of the sampling local. Was verified that all the analyzed elements presented concentrations below the maximum limit allowed to waters class 2, which may be distributed to domestic provisioning, to primary contact recreation, to vegetables and fruitier plants irrigation and to the natural and/or intensive breeding (agriculture) of species destined to the alimentation. In the sediment samples were determined Fe, Co, Ni, Cu, Zn and Pb, and was observed high contents to the elements Fe, Zn and Pb and relatively low concentrations of Co, Ni and Cu. It was verified

Drug residues in urban water: A database for ecotoxicological risk management.

Science.gov (United States)

Destrieux, Doriane; Laurent, François; Budzinski, Hélène; Pedelucq, Julie; Vervier, Philippe; Gerino, Magali

2017-12-31

Human-use drug residues (DR) are only partially eliminated by waste water treatment plants (WWTPs), so that residual amounts can reach natural waters and cause environmental hazards. In order to properly manage these hazards in the aquatic environment, a database is made available that integrates the concentration ranges for DR, which cause adverse effects for aquatic organisms, and the temporal variations of the ecotoxicological risks. To implement this database for the ecotoxicological risk assessment (ERA database), the required information for each DR is the predicted no effect concentrations (PNECs), along with the predicted environmental concentrations (PECs). The risk assessment is based on the ratio between the PNECs and the PECs. Adverse effect data or PNECs have been found in the publicly available literature for 45 substances. These ecotoxicity test data have been extracted from 125 different sources. This ERA database contains 1157 adverse effect data and 287 PNECs. The efficiency of this ERA database was tested with a data set coming from a simultaneous survey of WWTPs and the natural environment. In this data set, 26 DR were searched for in two WWTPs and in the river. On five sampling dates, concentrations measured in the river for 10 DR could pose environmental problems of which 7 were measured only downstream of WWTP outlets. From scientific literature and measurements, data implementation with unit homogenisation in a single database facilitates the actual ecotoxicological risk assessment, and may be useful for further risk coming from data arising from the future field survey. Moreover, the accumulation of a large ecotoxicity data set in a single database should not only improve knowledge of higher risk molecules but also supply an objective tool to help the rapid and efficient evaluation of the risk. Copyright © 2017 Elsevier B.V. All rights reserved.

Some techniques used in the treatment of phenolic waters residual

International Nuclear Information System (INIS)

Alzate S, Rafael A.; Botero, Carlos Andre

2000-01-01

The current state of the diverse processes of treatment of phenolic waters residual is presented, beginning with the methods traditionally employees, until finishing with those but recent innovations, which have been derived of the necessity of increasing the removal of these pollutants without increasing the costs of such processes in excessive form

Use of Cdse/ZnS quantum dots for sensitive detection and quantification of paraquat in water samples

Energy Technology Data Exchange (ETDEWEB)

Durán, Gema M. [Department of Analytical Chemistry and Food Technology, University of Castilla – La Mancha, Avenida Camilo José Cela, 10, 13004 Ciudad Real (Spain); IRICA (Regional Institute of Applied Scientific Research), Avenida Camilo José Cela, s/n., 13071 Ciudad Real (Spain); Contento, Ana M. [Department of Analytical Chemistry and Food Technology, University of Castilla – La Mancha, Avenida Camilo José Cela, 10, 13004 Ciudad Real (Spain); Ríos, Ángel, E-mail: Angel.Rios@uclm.es [Department of Analytical Chemistry and Food Technology, University of Castilla – La Mancha, Avenida Camilo José Cela, 10, 13004 Ciudad Real (Spain)

2013-11-01

Graphical abstract: -- Highlights: •Analytical use of CdSe/ZnS quantum dots. •Methodology for water solubilization of CdSe/ZnS QDs. •Sensitive and selective reaction with paraquat herbicide. •Application to water samples. -- Abstract: Based on the highly sensitive fluorescence change of water-soluble CdSe/ZnS core-shell quantum dots (QD) by paraquat herbicide, a simple, rapid and reproducible methodology was developed to selectively determine paraquat (PQ) in water samples. The methodology enabled the use of simple pretreatment procedure based on the simple water solubilization of CdSe/ZnS QDs with hydrophilic heterobifunctional thiol ligands, such as 3-mercaptopropionic acid (3-MPA), using microwave irradiation. The resulting water-soluble QDs exhibit a strong fluorescence emission at 596 nm with a high and reproducible photostability. The proposed analytical method thus satisfies the need for a simple, sensible and rapid methodology to determine residues of paraquat in water samples, as required by the increasingly strict regulations for health protection introduced in recent years. The sensitivity of the method, expressed as detection limits, was as low as 3.0 ng L{sup −1}. The lineal range was between 10–5 × 10{sup 3} ng L{sup −1}. RSD values in the range of 71–102% were obtained. The analytical applicability of proposed method was demonstrated by analyzing water samples from different procedence.

Use of Cdse/ZnS quantum dots for sensitive detection and quantification of paraquat in water samples

International Nuclear Information System (INIS)

Durán, Gema M.; Contento, Ana M.; Ríos, Ángel

2013-01-01

Graphical abstract: -- Highlights: •Analytical use of CdSe/ZnS quantum dots. •Methodology for water solubilization of CdSe/ZnS QDs. •Sensitive and selective reaction with paraquat herbicide. •Application to water samples. -- Abstract: Based on the highly sensitive fluorescence change of water-soluble CdSe/ZnS core-shell quantum dots (QD) by paraquat herbicide, a simple, rapid and reproducible methodology was developed to selectively determine paraquat (PQ) in water samples. The methodology enabled the use of simple pretreatment procedure based on the simple water solubilization of CdSe/ZnS QDs with hydrophilic heterobifunctional thiol ligands, such as 3-mercaptopropionic acid (3-MPA), using microwave irradiation. The resulting water-soluble QDs exhibit a strong fluorescence emission at 596 nm with a high and reproducible photostability. The proposed analytical method thus satisfies the need for a simple, sensible and rapid methodology to determine residues of paraquat in water samples, as required by the increasingly strict regulations for health protection introduced in recent years. The sensitivity of the method, expressed as detection limits, was as low as 3.0 ng L −1 . The lineal range was between 10–5 × 10 3 ng L −1 . RSD values in the range of 71–102% were obtained. The analytical applicability of proposed method was demonstrated by analyzing water samples from different procedence

Residual stress improved by water jet peening using cavitation for small-diameter pipe inner surfaces

International Nuclear Information System (INIS)

Yasuo, Nakamura; Toshizo, Ohya; Koji, Okimura

2001-01-01

As one of degradation conditions on components used in water, the overlapping effect of environment, material and stress might cause stress corrosion cracking (SCC). Especially, for the tensile residual stress produced by welding, it is particularly effective to reduce the tensile residual stress on the material surface to prevent SCC. In this paper, the residual stress improvement method using cavitation impact generated by a water jet, called Water Jet Peening (WJP), has been developed as the maintenance technology for the inner surfaces of small-diameter Ni-Cr-Fe alloy (Alloy 600) pipes. As the results, by WJP for the inner surface of Alloy 600 pipe (inner diameter; approximately 10-15 mm), we confirmed that the compressive stress generated within the range from the surface to the inner part about 0.5 mm deep and took a maximum value about 350 MPa on the surface. (author)

Radon measurement in Malaysia water samples

International Nuclear Information System (INIS)

Ibrahim, A.B.; Rosli Mahat; Yusof Md Amin

1995-01-01

This paper reported the results of the measurement of radon in local water. The water samples collected were rainwater, river water, seawater, well water or ground water at area of State of Selangor and Kuala Lumpur. The samples were collected in scintillation cell ZnS(Ag) through Radon Degassing Unit RDU 200. Alpha activity was counted with scintillation counters RD 200 at energy 5.5 MeV. (author)

Determination of ethephon residues in water by gas chromatography with cubic mass spectrometry after ion-exchange purification and derivatisation with N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide.

Science.gov (United States)

Royer, A; Laporte, F; Bouchonnet, S; Communal, P-Y

2006-03-03

An analytical method has been developed for the determination of residues of ethephon (2-chloroethyl phosphonic acid) in drinking and surface water. The procedure is based on de-ionisation with an anion/cation-exchange resin, solid phase extraction by means of anion-exchange polystyrene-divinylbenzene extraction disks, elution with a mixture of methanol and 10 M hydrochloric acid (98/2, v/v), redisolution into acetonitrile after evaporation and silylation with N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide (MTBSTFA). Quantification is performed by gas chromatography with ion-trap cubic mass spectrometric detection in the electron impact mode (GC-EI-MS3). Method validation was conducted using samples of mineral, tap, and river water that were fortified with ethephon at concentration levels ranging from 0.1 to 1.0 microg/L. The mean recovery from all the fortified samples (n = 36) amounted to 88% with a relative standard deviation of 17%. The method, therefore, was shown to allow accurate determination of ethephon residues in drinking and surface water with a limit of quantification of 0.1 microg/L.

ANALYSIS OF THE LEACHING EFFICIENCY OF INHIBITED WATER AND TANK 23H SIMULANT IN REMOVING RESIDUES ON TANK 48H WALLS

International Nuclear Information System (INIS)

Fondeur, F; Thomas02 White, T; Lawrence Oji, L; Chris Martino, C; Bill Wilmarth, B

2006-01-01

Solid residues on two sets of thermowell pipe samples from the D2 riser in SRS Tank 48H were characterized. The residue thickness was determined using the ASTM standard D 3483-05 and was found to be three order of magnitudes below the 1mm thickness estimated from an earlier video of the tank cooling coil inspection. The actual estimated thickness ranged from 4 to 20.4 microns. The mass per unit area ranged from 1 to 5.3 milligrams per square inch. The residues appear to consist primarily of potassium tetraphenylborate (39.8 wt% KTPB) and dried salt solution (33.5 wt% total of nitrates, nitrites and oxalate salts), although ∼30% of the solid mass was not accounted for in the mass balance. No evidence of residue buildup was found inside the pipe, as expected. The residue leaching characteristics were measured by placing one pipe in inhibited water and one pipe in DWPF Recycle simulant. After soaking for less than 4 weeks, the inhibited water was 95.4% effective at removing the residue and the DWPF Recycle simulant was 93.5% effective. The surface appearance of the pipes after leaching tests appeared close to the clean shiny appearance of a new pipe. Total gamma counts of leachates averaged 48.1 dpm/ml, or an equivalent of 2.35E-11 Ci/gm Cs-137 (dry solids basis), which is much lower than the 1.4 E-03 Ci/gm expected for Tank 48 dry slurry solids

Impacts of channel morphology on residues and ecological risks of polychlorinated biphenyls in water and sediment in Chahe River

Directory of Open Access Journals (Sweden)

Zhen-hua Zhao

2016-10-01

Full Text Available The impacts of channel morphology on the residues and ecological risks of 14 polychlorinated biphenyl (PCB congeners in water and sediment were investigated in summer (July and autumn (September in the Chahe River, in Nanjing, China. The residual concentrations of tri-chlorobiphenyls (tri-CBs, PCB 18 and tetra-CBs (PCB 52 in water were significantly higher than those of penta-CBs to deca-CBs, and the average residual concentration of ∑PCBs (sum of 14 PCB congeners in summer was about six times higher than in autumn. However, the residues in sediment did not change significantly. Redundancy analysis (RDA indicated that channel morphology and the corresponding environmental indices had significant impacts on PCB residues and their composition profiles in water and sediment. The overflow weir and lake-type watercourse may remarkably reduce the residual concentration and ecological risks of PCBs in water. The highest reduction percentages of the residual concentration and ecological risks of ∑PCBs induced by an overflow weir were 78% and 67%, respectively, and those induced by a lake-type watercourse were 36% and 70%, respectively. The watercourses with different channel morphologies were ranked by residual ∑PCBs concentrations in the following descending order: the natural ecological watercourse, vertical concrete watercourse, and vegetation-type riprap watercourse. However, they were ranked by residual ∑PCBs concentrations in sediment in the following descending order: the vertical concrete watercourse, vegetation-type riprap watercourse, and natural ecological watercourse.

Polar drug residues in sewage and natural waters in the state of Rio de Janeiro, Brazil.

Science.gov (United States)

Stumpf, M; Ternes, T A; Wilken, R D; Rodrigues, S V; Baumann, W

1999-01-12

The drug residues of lipid regulators, anti-inflammatories and some drug metabolites have been detected in raw sewage, treated waste water and river water in the state of Rio de Janeiro, Brazil. These residues are mainly derived from humans via excretion. The median concentrations in the effluents of sewage treatment plants (STPs) of most drugs investigated in this study ranged from 0.1 to 1 microgram/l. The removal rates of individual drugs during passage through a Brazilian STP varied from 12 to 90%. As a consequence of the incomplete removal of these residues during passage through a STP, rivers were also found to be contaminated. Median concentrations ranged from between 0.02 and 0.04 microgram/l in river water, whereas the maximum values were observed to be up to 0.5 microgram/l.

Napropamide residues in runoff and infiltration water from pepper production.

Science.gov (United States)

Antonious, George F; Patterson, Matthew A

2005-01-01

A field study was conducted on a Lowell silty loam soil of 2.7% organic matter at the Kentucky State University Research Farm, Franklin County, Kentucky. Eighteen universal soil loss equation (USLE) standard plots (22 x 3.7 m each) were established on a 10% slope. Three soil management practices were used: (i) class-A biosolids (sewage sludge), (ii) yard waste compost, each mixed with native soil at a rate of 50 ton acre(-1) on a dry-weight basis, and (iii) a no-mulch (NM) treatment (rototilled bare soil), used for comparison purposes. Devrinol 50-DF "napropamide" [N,N-diethyl-2-(1-naphthyloxy) propionamide] was applied as a preemergent herbicide, incorporated into the soil surface, and the plots were planted with 60-day-old sweet bell pepper seedlings. Napropamide residues one hour following spraying averaged 0.8, 0.4, and 0.3 microg g(-1) dry soil in sewage sludge, yard waste compost, and no-mulch treatments, respectively. Surface runoff water, runoff sediment, and napropamide residues in runoff were significantly reduced by the compost and biosolid treatments. Yard waste compost treatments increased water infiltration and napropamide residues in the vadose zone compared to sewage sludge and NM treatments. Total pepper yields from yard waste compost amended soils (9187 lbs acre(-1)) was significantly higher (P soil amended with class-A biosolids (6984 lbs acre(-1)) or the no-mulch soil (7162 lbs acre(-1)).

Mitigation of dimethazone residues in soil and runoff water from agricultural field.

Science.gov (United States)

Antonious, George F

2011-01-01

Dimethazone, also known as clomazone [2-[(2-chlorophenyl) methyl]- 4,4-dimethyl-3-isoxaolidinone] is a pre-emergent nonionic herbicide commonly used in agriculture. A field study was conducted on a silty-loam soil of 10 % slope to monitor off-site movement and persistence of dimethazone in soil under three management practices. Eighteen plots of 22 x 3.7 m each were separated using stainless steel metal borders and the soil in six plots was mixed with municipal sewage sludge (MSS) and yard waste (YW) compost (MSS+YW) at 15 t acre⁻¹ on dry weight basis, six plots were mixed with MSS at 15 t acre⁻¹, and six unamended plots (NM) were used for comparison purposes. The objectives of this investigation were to: (i) monitor the dissipation and half-life (T₁/₂) of dimethazone in soil under three management practices; (ii) determine the concentration of dimethazone residues in runoff and infiltration water following natural rainfall events; and (iii) assess the impact of soil amendments on the transport of NO₃, NH₄, and P into surface and subsurface water. Gas chromatography/mass spectrometery (GC/MS) analyses of soil extracts indicated the presence of ion fragments at m/z 125 and 204 that can be used for identification of dimethazone residues. Intitial deposits of dimethazone varied from 1.3 μg g⁻¹ dry native soil to 3.2 and 11.8 μg g⁻¹ dry soil in MSS and MSS+YW amended soil, respectively. Decline of dimethazone residues in the top 15 cm native soil and soil incorporated with amendments revealed half-life (T₁/₂) values of 18.8, 25.1, and 43.0 days in MSS+YW, MSS, and NM treatments, respectively. Addition of MSS+YW mix and MSS alone to native soil increased water infiltration, lowering surface runoff water volume and dimethazone residues in runoff following natural rainfall events.

Computed distributions of residual shaft drilling and drift construction water in the exploratory facilities at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Eaton, R.R.; Peterson, A.C.

1990-01-01

This paper contains the results of engineering analytical calculations of the potential distribution of residual construction water in the exploratory shafts and drifts and numerical calculations of the movement of the residual water and how the movement is affected by drift ventilation. Rock saturation is addressed

[Determination of buprofezin, methamidophos, acephate, and triazophos residues in Chinese tea samples by gas chromatography].

Science.gov (United States)

Zhang, Shuiba; Yi, Jun; Ye, Jianglei; Zheng, Wenhui; Cai, Xueqin; Gong, Zhenbin

2004-03-01

A method has been developed for the simultaneous determination of buprofezin, methamidophos, acephate and triazophos residues in Chinese tea samples. The pesticide residues were extracted from tea samples with a mixture of ethyl acetate and n-hexane (50:50, v/v) at 45 degrees C. The extracts were subsequently treated with a column packed with 40 mg of active carbon by gradient elution with ethyl acetate and n-hexane. Buprofenzin and the three organophosphorus pesticides were analyzed by gas chromatography using a DB-210 capillary column and a nitrogen-phosphorus detector. The recoveries for spiked standards were 73.4%-96.9%. The relative standard deviations were all within 4.63%. The limits of quantitation (3sigma) in the tea samples were about 7.0-12.0 microg/kg.

An extension of command shaping methods for controlling residual vibration using frequency sampling

Science.gov (United States)

Singer, Neil C.; Seering, Warren P.

1992-01-01

The authors present an extension to the impulse shaping technique for commanding machines to move with reduced residual vibration. The extension, called frequency sampling, is a method for generating constraints that are used to obtain shaping sequences which minimize residual vibration in systems such as robots whose resonant frequencies change during motion. The authors present a review of impulse shaping methods, a development of the proposed extension, and a comparison of results of tests conducted on a simple model of the space shuttle robot arm. Frequency shaping provides a method for minimizing the impulse sequence duration required to give the desired insensitivity.

Pesticide residue profile and nutrient characteristics of the Densu River Basin in Ghana

International Nuclear Information System (INIS)

Fianko, J.R.

2010-01-01

The Densu River Basin is one of the largest agricultural areas in Ghana. About 80% of people living in this area rely on agricultural activities for subsistence. The practice of using pesticides such as organochlorines, organophosphates, carbamates, pyrethroids and several others in agriculture and public health programs have raised concerns about potentially adverse effects on human health and the environment. Assessment of human health implications of non-point sources within a river basin include pesticide residues analysis of water, sediment and fish and monitoring of physico-chemical parameters in waters that serve as source of drinking water for the entire community within the basin. In this study, a field survey was conducted to assess farmers' knowledge of safe handling and use of pesticides. Nutrient chemistry and surface water characteristics of the Densu River and its tributaries, type and levels of pesticide residues and their trends in water, sediment and fish in the basin were also evaluated. The study also assessed the health risk associated with pesticide contamination of fish from the Basin as well as the relationship between land use and groundwater contamination. Generally surface and ground water bodies in the Densu River basin were found to be polluted with respect to nutrients and pesticides. Waters from the basin were found to be fresh, slightly acidic, and weakly mineralized with low chemical constituents. Nitrate (NO 3- N) levels in surface water ranged between 0.12 - 31.07 mgL -1 while ammonia was between 0.01 - 2.10 mgL -1 and that of phosphate was 0.012 - 2.45 mgL -1 . Pesticide residues and metabolites detected in water, sediment and fish samples from the Densu River Basin were organochlorines. In an average 96% of fish samples, 13.69% of sediment and 3.30% of water samples, at least one pesticide residue was detected per sample. Of the numerous pesticides evaluated, γ -HCH, DDT, aldrin, dieldrin, DDE, endosulfan sulphate, �

Evaluation of Patterns and Spatial Trends of Pesticide Residues ...

African Journals Online (AJOL)

This paper reports on the analysis of organochlorine pesticides pollution data obtained from samples collected from Vikuge farm, Coast Region, Tanzania between 2000 and 2003 by principal component analysis (PCA). PCA of the data sets for pesticide residues in water, soil and sediments samples from Vikuge has shown ...

Magnitude of [14C] DDT residues in stored dried fish and pre-cooking processing effect on their removal

International Nuclear Information System (INIS)

Rahman, M.; Khatoon, J.; Matin, M.A.; Main, A.J.

1998-01-01

Residues of 14 C-DDT in stored dried fish was determined under ambient conditions for a 6 month period. Immediately after treatment, about 40% of the applied DDT was eliminated from surface of the dried fish with water washing. However, such removal was reduced to about 26% on storage for 6 months. Boiling of dried fish in water resulted in further removal of about 16% residues. In boiled dried fish, about 14% residues might remain and this could be removed by Soxhlet extraction. Surface extraction with hexane yielded about 80% of the residues immediately after treatment and the extractable residues decreased to about half the initial value of 6 months' storage. Dried fish residues, on surface extraction with water or hexane, when subjected to exhaustive Soxhlet extraction with methanol was found to result in further recovery of about 39-49% and 17-32%, respectively. Bound DDT residues were found to be about 5% in water washed dried fish samples and about 1.5% in case of hexane-extracted samples. Degradation of parent DDT to DDE and DDD was found. Maximum values of 16.58% DDE and 21.6% DDD were found in dried fish stored for 6 months. (author)

Polycyclic Aromatic Hydrocarbon Residues in Serum Samples of Autopsied Individuals from Tennessee

Directory of Open Access Journals (Sweden)

Aramandla Ramesh

2014-12-01

Full Text Available This study reports the concentrations of Polycyclic Aromatic Hydrocarbons (PAHs in human blood sera samples (n = 650 obtained at autopsy from individuals who died of drug abuse, alcohol toxicity, homicide, suicide and other unknown causes. The analyzed samples from decedents revealed the presence of PAHs of which B(aP was the most predominant one, followed by benzo(bfluoranthene and benzo(kfluoranthene. The other PAHs detected sporadically and measured were benzo(g,h,iperylene, acenaphthene, anthracene, phenanthrene, and fluoranthene The mean concentrations of PAHs were greater in the twenties to fifties age groups compared to others. The PAH residue levels detected were high in African Americans compared to Caucasians, Asians, and Hispanics. It appears that environmental exposure, dietary intake and in some cases occupational exposure may have contributed to the PAH body burden. While the PAH residue concentrations measured fall within the range of those reported for healthy adults elsewhere, in isolated cases, the concentrations detected were high, calling the need for a reduction in PAH emissions and human biomonitoring studies for purposes of risk assessment.

Estimation of deltamethrin residues in cow's and goat's environment and trials to reduce its level in milk

Directory of Open Access Journals (Sweden)

Halla E. K. El Bahgy

2018-05-01

Full Text Available Aim: The present study was aimed to estimate deltamethrin residues in cow's and goat's environment over a certain period of time post-application, to identify the role of both feed and water as a source of pesticides, and to conduct some trials to reduce their levels in milk. Materials and Methods: A total of 80 water and feed samples (40 of each and 120 milk samples (80 cow's milk and 40 goat's milk were collected. Fresh milk samples were collected directly from the udder as well as from feed and water before application and 1st, 2nd, 3rd, 7th, 15th, 21st, and 35th days after insecticide application. Results: Deltamethrin residues were detected after its application in both water and feed at different levels up to the first 3 days and in all cow's and goat's milk samples at 35th day. The highest levels were detected in milk samples at the 2nd day then at the 7th day followed at the 15th day after application as such levels were above the maximum residual limits. By microwaving the polluted cow's milk samples, deltamethrin residues were not detected without influencing the chemical composition of the milk. However, on freezing of milk, the deltamethrin residues reached 12.6±3.24 μg/L in association with a significant decline in the concentration of fat. Conclusion: Microwaving of milk is an effective method to decline deltamethrin concentration in milk.

Important aspects of residue sampling in drilling dikes; Aspectos importantes para a amostragem de residuos em diques de perfuracao

Energy Technology Data Exchange (ETDEWEB)

Silva, Gilvan Ferreira da [PETROBRAS, Rio de Janeiro (Brazil). Centro de Pesquisas. Div. de Explotacao

1990-12-31

This paper describes the importance of sampling in the evaluation of physical and chemical properties of residues found in drilling dikes, considering the later selection of treatment methods or discard of these residues. We present the fundamental concepts of applied statistics, which are essential to the elaboration of sampling plans, with views of obtaining exact and precise results. Other types of samples are also presented, as well as sampling equipment and methods for storage and preservation of the samples. As a conclusion, we the example of the implementation of a sampling plan. (author) 3 refs., 9 figs., 3 tabs.

Important aspects of residue sampling in drilling dikes; Aspectos importantes para a amostragem de residuos em diques de perfuracao

Energy Technology Data Exchange (ETDEWEB)

Silva, Gilvan Ferreira da [PETROBRAS, Rio de Janeiro (Brazil). Centro de Pesquisas. Div. de Explotacao

1989-12-31

This paper describes the importance of sampling in the evaluation of physical and chemical properties of residues found in drilling dikes, considering the later selection of treatment methods or discard of these residues. We present the fundamental concepts of applied statistics, which are essential to the elaboration of sampling plans, with views of obtaining exact and precise results. Other types of samples are also presented, as well as sampling equipment and methods for storage and preservation of the samples. As a conclusion, we the example of the implementation of a sampling plan. (author) 3 refs., 9 figs., 3 tabs.

Chemical composition and mixing-state of ice residuals sampled within mixed phase clouds

Science.gov (United States)

Ebert, M.; Worringen, A.; Benker, N.; Mertes, S.; Weingartner, E.; Weinbruch, S.

2010-10-01

During an intensive campaign at the high alpine research station Jungfraujoch, Switzerland, in February/March 2006 ice particle residuals within mixed-phase clouds were sampled using the Ice-counterflow virtual impactor (Ice-CVI). Size, morphology, chemical composition, mineralogy and mixing state of the ice residual and the interstitial (i.e., non-activated) aerosol particles were analyzed by scanning and transmission electron microscopy. Ice nuclei (IN) were identified from the significant enrichment of particle groups in the ice residual (IR) samples relative to the interstitial aerosol. In terms of number lead-bearing particles are enriched by a factor of approximately 25, complex internal mixtures with silicates or metal oxides as major components by a factor of 11, and mixtures of secondary aerosol and soot (C-O-S particles) by a factor of 2. Other particle groups (sulfates, sea salt, Ca-rich particles, external silicates) observed in the ice-residual samples cannot be assigned unambiguously as IN. Between 9 and 24% of all IR are Pb-bearing particles. Pb was found as major component in around 10% of these particles (PbO, PbCl2). In the other particles, Pb was found as some 100 nm sized agglomerates consisting of 3-8 nm sized primary particles (PbS, elemental Pb). C-O-S particles are present in the IR at an abundance of 17-27%. The soot component within these particles is strongly aged. Complex internal mixtures occur in the IR at an abundance of 9-15%. Most IN identified at the Jungfraujoch station are internal mixtures containing anthropogenic components (either as main or minor constituent), and it is concluded that admixture of the anthropogenic component is responsible for the increased IN efficiency within mixed phase clouds. The mixing state appears to be a key parameter for the ice nucleation behaviour that cannot be predicted from the separate components contained within the individual particles.

Chemical composition and mixing-state of ice residuals sampled within mixed phase clouds

Directory of Open Access Journals (Sweden)

M. Ebert

2011-03-01

Full Text Available During an intensive campaign at the high alpine research station Jungfraujoch, Switzerland, in February/March 2006 ice particle residuals within mixed-phase clouds were sampled using the Ice-counterflow virtual impactor (Ice-CVI. Size, morphology, chemical composition, mineralogy and mixing state of the ice residual and the interstitial (i.e., non-activated aerosol particles were analyzed by scanning and transmission electron microscopy. Ice nuclei (IN were identified from the significant enrichment of particle groups in the ice residual (IR samples relative to the interstitial aerosol. In terms of number lead-bearing particles are enriched by a factor of approximately 25, complex internal mixtures with silicates or metal oxides as major components by a factor of 11, and mixtures of secondary aerosol and carbonaceous material (C-O-S particles by a factor of 2. Other particle groups (sulfates, sea salt, Ca-rich particles, external silicates observed in the ice-residual samples cannot be assigned unambiguously as IN. Between 9 and 24% of all IR are Pb-bearing particles. Pb was found as major component in around 10% of these particles (PbO, PbCl₂. In the other particles, Pb was found as some 100 nm sized agglomerates consisting of 3–8 nm sized primary particles (PbS, elemental Pb. C-O-S particles are present in the IR at an abundance of 17–27%. The soot component within these particles is strongly aged. Complex internal mixtures occur in the IR at an abundance of 9–15%. Most IN identified at the Jungfraujoch station are internal mixtures containing anthropogenic components (either as main or minor constituent, and it is concluded that admixture of the anthropogenic component is responsible for the increased IN efficiency within mixed phase clouds. The mixing state appears to be a key parameter for the ice nucleation behaviour that cannot be predicted from the sole knowledge of the main component of an individual particle.

Control system of an anaerobia reactor used in the treatment of the Industrial residual waters

International Nuclear Information System (INIS)

Duque, Mauricio; Giraldo, Eugenio; Bello Frank

1995-01-01

The technology of the anaerobia digestion, has had a wide acceptance in the Colombian means for the treatment of industrial residual waters, especially for the economic advantages that it present and the good purification results. The technology of the anaerobia digestion for the treatment of residual waters, is based in the conversion of the organic matter present in the polluted waters, in methane and carbon dioxide. These two gases are removed of the reactor by means of special structures of gathering. Microorganisms that are sensitive to the changes of the pH mediate the conversion of the organic matter to CH4 and CO2. Therefore, the control on the pH is necessary for a correct behavior of the reactor. At the moment many industries are implementing plans of contamination control, that involve treatment of residual waters for means anaerobia. The present investigation is part of a wide work program in the technology of the anaerobia digestion. It is looked for to develop a monitored system and automatic control of reactors discharge anaerobia appraises, in a combined effort among the departments of Civil and Electric Engineering of the Andes University

Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals; Cuantificacion de metales pesados de lodo residual y cenizas de la planta tratadora de aguas residuales Reciclagua y efectos a la salud de los trabajadores que manipulan los residuos

Energy Technology Data Exchange (ETDEWEB)

Guerrero D, J.J

2004-07-01

In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

Water fluxes in maize, millet and soybean plant-residue mulches used in direct seeding

International Nuclear Information System (INIS)

Silva, Fernando Antonio Macena da; Pinto, Hilton Silveira; Scopel, Eric; Corbeels, Marc; Affholder, Francois

2006-01-01

The objective of this work was to evaluate the effects of crop residue mulches from maize, millet and soybean on water storage capacity, water evaporation, soil cover, solar radiation interception and surface water run-off as well as to incorporate these effects in a crop growth model. The mulch of millet and maize presented higher capacity for water storage than soybean mulch: 3.26, 3.24 and 2.62 g of water per gram of dry matter, respectively. Water losses from wet mulches were related to the potential evapotranspiration. The soil cover levels were similar among the three types of material. The three types of mulch intercepted similar quantities of photosynthetically active radiation and infrared radiation. The mulch of maize straw was slightly more efficient in intercepting radiation than that from millet or soybean. Mulching with millet residues was efficient in the control of surface water run-off: only 45.5 mm of water (out of 843.5 mm rainfall) was lost through runoff under the no-till system with millet as cover crop, whereas 222.5 mm of water was lost in the conventional system with tillage. Most of the relations derived in this work could be described by exponential models. (author)

Mutagenicity of pan residues and gravy from fried meat.

Science.gov (United States)

Overvik, E; Nilsson, L; Fredholm, L; Levin, O; Nord, C E; Gustafsson, J A

1987-02-01

Lean pork meat was fried with or without the addition of frying-fat at 200 or 250 degrees C. The pan residues were collected by washing the hot pan with boiling water. When producing thickened gravy the water was substituted by a mixture of water and flour, milk and flour or cream and flour. The basic extracts were tested for mutagenicity in Ames' Salmonella test on strain TA98 with the addition of S9 mix. High amounts of mutagenicity were found in all samples. The amounts of mutagenicity in the pan residues were at a comparable level of the amounts found in the meat crusts. Thickening of the gravy caused only small changes in the mutagenicity.

Determination of Antibiotic Residues in Milk by Microbial Inhibitory Tests

Directory of Open Access Journals (Sweden)

Juščáková D.

2017-09-01

Full Text Available Undesirable substances enter the organism of animals mostly via feed, water or veterinary medicines and their residues pass subsequently into the products of animal origin. In dairy cows, sheep and goats these residues are eliminated particularly in milk. Milk intended for human consumption must comply with safety criteria also with respect to residues of antibiotics. The aim of this study was to determine the presence or absence of antibiotic residues in the milk using the tests Milchtest and Premi®Test. While the Milchtest was developed for the determination of antibiotic residues in cow, sheep and goat milk, the Premi®Test is intended for the determination of antibiotic residues in meat juice, liver, kidneys, fish, eggs and in the urine of animals treated with antibiotics. As examined matrices, we used 45 samples of raw cow’s milk collected at 3 agricultural farms and 10 samples of milk offered to consumers at grocery stores. When using the Milchtest, 8 samples tested positive and 10 provided dubious results while testing with the Premi®Test showed that only 6 samples were positive for antibiotics. Comparison of the results confirmed a higher detection sensitivity of Milchtest reflected in higher numbers of positive samples and the detection of dubious results in samples of raw cow’s milk. However, it should be noted that even the Premi®Test, although not intended preferably for the determination of antibiotics in milk, can be used, if needed, for the preliminary screening of antibiotic residues in such a matrix.

Verification of an optimized condition for low residual stress employed water-shower cooling during welding in austenitic stainless steel plates

International Nuclear Information System (INIS)

Yanagida, N.; Enomoto, K.; Anzai, H.

2004-01-01

To reduce tensile residual stress in a welded region, we have developed a new cooling method that uses a water-shower behind the welding torch. When this method is applied to the welding of austenitic stainless steel, the welding and cooling conditions mainly determine how much the residual stress can be reduced. To optimize these conditions, we first used a robust design method to determine the effects of the preheating temperature, the heat input quantity, and the water-shower area on the residual stress, and found that, to decrease the tensile residual stress, the preheating temperature should be high, the heat input low, and the water-shower area large. To confirm the effectiveness of these optimized conditions, the residual stresses under optimized or non-optimized conditions were measured experimentally. It was found that the residual stresses were tensile under the non-optimized conditions, but compressive under the optimized ones. These measurements agree well with the 3D-FEM analyses. It can therefore be concluded that the optimized conditions are valid and appropriate for reducing residual stress in an austenitic stainless-steel weld. (orig.)

Pesticide residue assessment in three selected agricultural production systems in the Choluteca River Basin of Honduras

International Nuclear Information System (INIS)

Kammerbauer, J.; Moncada, J.

1999-01-01

There is a basic lack of information about the presence of pesticide residues in the environment in Central America. Over the period of February 1995 to June 1997, river, well, lagoon and spring water samples, as well as soil, fish tissue, lagoon bed sediments and some foodstuffs were taken from the greater Cholutecan River Basin of Honduras and analyzed for pesticide residues. These were collected at three separate sites (La Lima, Zamorano and Choluteca), each characterized by differing agricultural production systems. The main pesticide residues found in soil samples were dieldrin and p,p'-DDT, while river water samples were found to have detectable levels of heptachlor, endosulfan and chlorpyrifos, with lagoon and well water also being shown to contain heptachlor. These pesticides detected were in more than 20% of the samples assessed. In river water samples more pesticide residues at higher concentrations were found to be associated with areas of more intensive agricultural production. The fewest pesticides with lowest concentrations were found in the small subwatershed associated with traditional agricultural production. Although the pesticides found in the soils at the three sites were generally similar they tended to be higher in the southern part of the Cholutecan watershed, followed by the central zone, with the lowest concentrations being found in the more traditional production zone. In lagoon and well water samples more pesticides, but mostly in lower concentrations were detected at the traditional production site than at the others. Ten pesticide compounds were detected in fish tissue, mainly organochlorines, some of which were also found in lagoon sediments. In terms of food products, almost no pesticides were detected in vegetables, but the kidney adipose tissue taken from slaughtered cows was shown to have a tendency to contain some organochlorines. Spring water in the traditional agricultural production zone contained three organochlorine compounds

A new chiral residue analysis method for triazole fungicides in water using dispersive liquid-liquid microextraction (DLLME).

Science.gov (United States)

Luo, Mai; Liu, Donghui; Zhou, Zhiqiang; Wang, Peng

2013-09-01

A rapid, simple, reliable, and environment-friendly method for the residue analysis of the enantiomers of four chiral fungicides including hexaconazole, triadimefon, tebuconazole, and penconazole in water samples was developed by dispersive liquid-liquid microextraction (DLLME) pretreatment followed by chiral high-performance liquid chromatography (HPLC)-DAD detection. The enantiomers were separated on a Chiralpak IC column by HPLC applying n-hexane or petroleum ether as mobile phase and ethanol or isopropanol as modifier. The influences of mobile phase composition and temperature on the resolution were investigated and most of the enantiomers could be completely separated in 20 min under optimized conditions. The thermodynamic parameters indicated that the separation was enthalpy-driven. The elution orders were detected by both circular dichroism detector (CD) and optical rotatory dispersion detector (ORD). Parameters affecting the DLLME performance for pretreatment of the chiral fungicides residue in water samples, such as the extraction and dispersive solvents and their volume, were studied and optimized. Under the optimum microextraction condition the enrichment factors were over 121 and the linearities were 30-1500 µg L(-1) with the correlation coefficients (R(2)) over 0.9988 and the recoveries were between 88.7% and 103.7% at the spiking levels of 0.5, 0.25, and 0.05 mg L(-1) (for each enantiomer) with relative standard deviations varying from 1.38% to 6.70% (n = 6) The limits of detection (LODs) ranged from 8.5 to 29.0 µg L(-1) (S/N = 3). © 2013 Wiley Periodicals, Inc.

Chemical Control of Black Flies in Large Rivers as an Impact in Agrochemical Residue-Biota Interactions in Water Ecosystems

International Nuclear Information System (INIS)

Haufe, W.O.

1981-01-01

Livestock losses have been an obstacle to economic development of the farming and livestock industry in more northerly areas of Canada until two species of black fly, Simulium arcticum and S. luggeri, outbreaks are controlled effectively. The problem is complicated by its association with an abundance of large rivers and streams. Since effective control of black flies is presently limited to reduction of their breeding sources in flowing water, the managers of Canadian inland waters have been concerned about any major practice of using pesticides as black fly larvicides. Consequently, Canadian inland waters have been subject to continuous monitoring of major drainage systems with special attention to the chlorinated hydrocarbon insecticides. The latest status of residues was published from a Canadian Survey of 333 sampling locations between 1972 and 1975

Tracking persistent pharmaceutical residues from municipal sewage to drinking water

Science.gov (United States)

Heberer, Thomas

2002-09-01

In urban areas such as Berlin (Germany) with high municipal sewage water discharges and low surface water flows there is a potential risk of drinking water contamination by polar organic compounds when groundwater recharge is used in drinking water production. Thus, some pharmaceutically active compounds (PhACs) are not eliminated completely in the municipal sewage treatment plants (STPs) and they are discharged as contaminants into the receiving waters. In terms of several monitoring studies carried out in Berlin between 1996 and 2000, PhACs such as clofibric acid, diclofenac, ibuprofen, propyphenazone, primidone and carbamazepine were detected at individual concentrations up to the μg/l-level in influent and effluent samples from STPs and in all surface water samples collected downstream from the STPs. Under recharge conditions, several compounds were also found at individual concentrations up to 7.3 μg/l in samples collected from groundwater aquifers near to contaminated water courses. A few of the PhACs were also identified at the ng/l-level in Berlin tap water samples.

Endosulfan residues in fish from the MUDA rice agroecosystem

International Nuclear Information System (INIS)

Nashriyah Mat; Sabri Junoh; Nuriati Nurdin

2002-01-01

A study was carried out in the recycled and the non-recycled areas of the Muda rice agroecosystem to determine the residue level of endosulfan in rice field fish. Snakehead or haruan (Channa striata), climbing perch or puyu (Anabas testudineus), walking catfish or keli (Clariasspp.) and snakeskin gouramy or sepat siam (Trichogasterpectoralis) were sampled and the tissues analysed using Gas Liquid Chromatography. Endosulfan sulphate metabolite was a ubiquitous residue in all fish at levels ranging from 0.0065 μg/g to 0.9837 μg/g of tissue wet weight whilst α-isomer was detected at a much lower concentration followed by β-isomer. In Channa striata, endosulfan total residue (α+β+sulphate) was accumulated in fish tissues sampled at ACRBD4 (non-recycled) site followed by Blok 14 (recycled) site. Endosulfan residue concentration did not coincide with water recycling practice nor changes in EROD enzyme activity. (Author)

Experimental determination of residual stress by neutron diffraction in a boiling water reactor core shroud

International Nuclear Information System (INIS)

Payzant, A.; Spooner, S.; Zhu, Xiaojing; Hubbard, C.R.

1996-01-01

Residual strains in a 51 mm (2-inch) thick 304L stainless steel plate have been measured by neutron diffraction and interpreted in terms of residual stress. The plate, measuring (300 mm) in area, was removed from a 6m (20-ft.) diameter unirradiated boiling water reactor core shroud, and included a multiple-pass horizontal weld which joined two of the cylindrical shells which comprise the core shroud. Residual stress mapping was undertaken in the heat affected zone, concentrating on the outside half of the plate thickness. Variations in residual stresses with location appeared consistent with trends expected from finite element calculations, considering that a large fraction of the residual hoop stress was released upon removal of the plate from the core shroud cylinder

Residues leaching from 'Factory of barren ores'

International Nuclear Information System (INIS)

Rakhmatov, N.; Khakimov, N.; Nazarov, Kh.M.; Barotov, A.M.

2012-01-01

The objective of the present work is safe management of residues from Factory of Barren Ores, their reprocessing, expenditures reduction for remediation of Istiklol city former uranium tailings. For this purpose, some experiences were adopted - Factory of Barren Ores tailing use for filling up the open pit where water with uranium content 3-5 mg/l is located. Factory of Barren Ores waste are passed through heap leaching and have some amount of uranium salts dissolved in water. Thus, we propose to dissolve uranium from Factory of Barren Ores wastes with uranium bearing water flowing out from gallery and filling up the open-pit by radioactive wastes. In so doing, uranium content flowing out from gallery will increase twice, and further, passing them through apricot's shell, as a sorbent, we will clean the water against radionuclides. Residue samples with uranium content 0,015% from Factory of Barren Ores and uranium bearing waters from gallery 1 with uranium content 0,0025 g/l were used for laboratory tests. After which, a slurry was prepared by means of residue mixing with water in ratio of solid and liquid phases (S:L) - 1:2 and 9,7 ml of sulfuric acid (Ρ=1,82) was added which corresponds consumption by H 2 SO 4 176,54 kg/t. For the first test, leaching was carried out during 4 hours at ph=1,6 at room temperature. For the second test, leaching was carried out at 60 d eg C a nd ph=1,6 during 4 hours. Slurry heating and mixing was carried out by means of magnetic mixer. The basic residue leaching indicators are provided in this article.

Aging assessment of Residual Heat Removal systems in Boiling Water Reactors

International Nuclear Information System (INIS)

Lofaro, R.J.; Aggarwal, S.

1992-01-01

The effects of aging on Residual Heat Removal systems in Boiling Water Reactors have been studied as part of the Nuclear Plant Aging Research Program. The aging phenomena has been characterized by analyzing operating experience from various national data bases. In addition, actual plant data was obtained to supplement and validate the data base findings

Residues of PCDDs and PCDFs in human milk samples in Ahmedabad, India

Energy Technology Data Exchange (ETDEWEB)

Kashyap, R.; Bhatnagar, V.; Sadhu, H.; Jhamb, N.; Karanjkar, R.; Saiyed, H. [National Inst. of Occupational Health, Ahmedabad (India)

2004-09-15

Polychlorinated dibenzo-p-dioxins (PCDDs) and Polychlorinated dibenzo furans (PCDFs) represent a class of organic environmental pollutants. They are unwanted byproduct of incineration, uncontrolled burning and certain industrial processes. They are persistent in nature and bioaccumulates through food chain. These are hazardous to human health and environment. The residues of these toxicants have been detected in human adipose tissue, blood and milk. WHO has coordinated two rounds of follow up studies on levels of PCDD/Fs and PCBs in human milk and the data shows a decreasing trend during the last 30 years. However, in India there is no data available on the exposure and residues of these contaminants. This study presents first time the levels of dioxin and furans in human milk samples collected from the Ahmedabad city in India.

Release behavior of triazine residues in stabilised contaminated soils

International Nuclear Information System (INIS)

Ying, G.G.; Kookana, R.S.; Mallavarpu, M.

2005-01-01

This paper reports the release behavior of two triazines (atrazine and simazine) in stabilised soils from a pesticide-contaminated site in South Australia. The soils were contaminated with a range of pesticides, especially with triazine herbicides. With multiple extractions of each soil sample with deionised water (eight in total), 15% of atrazine and 4% of simazine residues were recovered, resulting in very high concentrations of the two herbicides in leachate. The presence of small fractions of surfactants was found to further enhance the release of the residues. Methanol content up to 10% did not substantially influence the concentration of simazine and atrazine released. The study demonstrated that while the stabilisation of contaminated soil with particulate activated carbon (5%) and cement mix (15%) was effective in locking the residues of some pesticides, it failed to immobilise triazine herbicides residues completely. Given the higher water solubility of these herbicides than other compounds more effective strategies to immobilise their residues is needed. - Stabilisation of contaminated soil with a mix of activated carbon and cement may fail to immobilise some contaminants like triazines

Optimization of immunochemistry for sensing techniques to detect pesticide residues in water

DEFF Research Database (Denmark)

Uthuppu, Basil; Kostesha, Natalie; Jakobsen, Mogens Havsteen

2011-01-01

We are working on the development of a real-time electrochemical sensor based on an immunoassay detection system to detect and quantify the presence of pesticide residues in ground water. Highly selective and sensitive immuno-reactions are being investigated to be optimized in order to bring them...

Mitigation of inside surface residual stress of type 304 stainless steel pipe welds by inside water cooling method

International Nuclear Information System (INIS)

Sasaki, R.

1980-01-01

The weld residual stress distributions, macro- and microstructures of heat affected zone and IGSCC susceptibility of Type 304 stainless steel pipe welds by natural and inside water cooling methods have been investigated. The residual stresses of pipe welds by the natural cooling method are high tensile on both the inside and the outside surface. While the residual stresses on the inside surface of pipe welds by the inside water cooling method are compressive in both axial and circumferential directions for each pipe size from 2 to 24 inch diameter. The sensitized zones of welds by the inside water cooling method are closer to the fusion line, much narrower and milder than those by the natural cooling method. According to the constant extension rate test results for specimens taken from the inside surface of pipe welds, the inside water cooled welds are more resistant to IGSCC than naturally cooled ones

Computed distributions of residual shaft drilling and construction water in the exploratory facilities at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Eaton, R.R.; Peterson, A.C.

1989-01-01

The Yucca Mountain Project is studying the feasibility of constructing a high-level nuclear waste repository at Yucca Mountain in southwest Nevada. One activity of site characterization is the construction of two exploratory shafts. This paper contains the results of engineering analytical calculations of the potential distribution of residual construction water in the exploratory shafts and drifts and numerical calculations of the movement of the residual water and how the movement is affected by drift ventilation. In all cases the increase in rock saturation resulting from the construction water was extremely small. 11 refs., 15 figs., 1 tab

Organochlorine pesticides residues in bottled drinking water from Mexico City.

Science.gov (United States)

Díaz, Gilberto; Ortiz, Rutilio; Schettino, Beatriz; Vega, Salvador; Gutiérrez, Rey

2009-06-01

This work describes concentrations of organochlorine pesticides in bottled drinking water (BDW) in Mexico City. The results of 36 samples (1.5 and 19 L presentations, 18 samples, respectively) showed the presence of seven pesticides (HCH isomers, heptachlor, aldrin, and p,p'-DDE) in bottled water compared with the drinking water standards set by NOM-127-SSA1-1994, EPA, and World Health Organization. The concentrations of the majority of organochlorine pesticides were within drinking water standards (0.01 ng/mL) except for beta-HCH of BW 3, 5, and 6 samples with values of 0.121, 0.136, and 0.192 ng/mL, respectively. It is important monitoring drinking bottled water for protecting human health.

Pesticide residues in individual versus composite samples of apples after fine or coarse spray quality application

DEFF Research Database (Denmark)

Poulsen, Mette E.; Wenneker, Marcel; Withagen, Jacques

2012-01-01

. None of the results for the pesticides residues measured in individual apples exceeded the EU Maximum Residue Levels (MRLs). However, there was a large variation in the residues levels in the apples, with levels from 0.01 to 1.4 mg kg−1 for captan, the pesticide with the highest variation, and from 0.......01 to 0.2 mg kg−1 for pyraclostrobin, the pesticide with the lowest variation. Residues of fenoxycarb and indoxacarb were only found in a few apples, probably due to the early application time of these two compounds. The evaluation of the effect of spray quality did not show any major difference between......In this study, field trials on fine and coarse spray quality application of pesticides on apples were performed. The main objectives were to study the variation of pesticide residue levels in individual fruits versus composite samples, and the effect of standard fine spray quality application...

Residues of selected antibiotics in the South Moravian Rivers, Czech Republic.

Science.gov (United States)

Jarova, Katerina; Vavrova, Milada; Koleckarova, Alice

2015-01-01

The aim of this study was to assess the contamination level of aquatic ecosystems of the Oslava and the Jihlava Rivers, and of the Nove Mlyny Water Reservoir, situated in the South Moravian Region (Czech Republic), by residues of selected veterinary pharmaceuticals. We isolated and determined 10 sulfonamide antibiotics in samples of surface water and bottom sediments using optimized analytical methods. A representative number of sampling sites in the entire basin of selected waters were chosen. Samples were collected particularly near the larger cities in order to assess their possible impact to the aquatic ecosystems. Extraction, pre-concentration and purification of samples were performed using optimized methods of solid phase extraction and pressurized solvent extraction. Final identification and quantification were carried out by high-performance liquid chromatography coupled with diode array detector. The concentration of sulfonamides in water samples were all under the limit of detection. Regarding sediment samples, sulfadimidine was found at most sampling sites; its highest values were recorded in the Jihlava River (up to 979.8 µg.kg(-1) dry matter). Other frequently detected sulfonamides were sulfamethoxazole and sulfamerazine. Most other sulfonamides were under the limit of detection or limit of quantification. Monitoring of antibiotic residues in the environment, especially in the aquatic ecosystem, is a current topic due to the growing worldwide use in both human and veterinary medicine. According to obtained results, we document the pollution of selected rivers and water reservoir by particular sulfonamides which basically reflects their application in veterinary medicine.

Distribution and migration of pesticide residues in mosquito control impoundments St. Lucie County, Florida, USA

Science.gov (United States)

Parkinson, R. W.; Wang, T. C.; White, J. R.; David, J. R.; Hoffman, M. E.

1993-09-01

This project was designed to: (1) document the distribution and migration of organochlorine pesticide residues within marsh substrates of 18 St. Lucie County mosquito control impoundments located along the Indian River Lagoon estuary, and (2) evaluate the impact of water management techniques on residue mobility. Our results indicate that detectible concentrations of organochlorine compounds, applied between the late 1940s and early 1950s, are present in 16 of the 18 St. Lucie County mosquito control impoundments. These compounds are primarily restricted to the surficial, organic-rich wetland sediment, which, based upon geotechnical analysis, was exposed to the atmosphere at a time when the impoundments were subjected to pesticide treatment. Contaminated sediments are present below the surficial, organic-rich layer, suggesting that some vertical migration of pesticides has occurred. It is unlikely that leaching associated with the downward percolation of impounded water was responsible for this migration as pesticide residues were never detected within the in situ pore waters. An alternative explanation is that biological processes (e.g., rooting, burrowing) facilitated the downward flux of organochlorine compounds into sediment horizons not subjected to direct treatment. Eighty-eight surface water samples obtained from two impoundments subjected to contrasting water management techniques were analyzed for pesticide content. None of the surficial water samples collected in association with these impoundments contained detectible concentrations of organochlorine compounds. These samples were unfiltered and contained as much as 25 mg/1 of particulate organic matter. This suggests that the currently preferred management technique (RIM), which is designed to maintain water quality, limit mosquito production, and provide for ecological continuity, does not hydraulically mobilize pesticide residues into the Indian River Lagoon estuary.

Water sampling device for fuel rod failure monitoring

International Nuclear Information System (INIS)

Oogami, Hideaki; Echigoya, Hironori; Matsuoka, Tesshi.

1991-01-01

The device of the present invention accurately samples coolants in a channel box as sampling water even if the upper end of the channel box of a fuel assembly is positioned at the same height or lower than the upper end of an upper lattice plate. An existent device comprises an outer cap, an inner cap, an air supply pipe and a water sampling tube. In addition, the device of the present invention comprises a sealing material disposed at the end of the outer cap for keeping liquid sealing with the upper lattice plate and a water level monitoring pipe extended to lower than the inner cap passing through the liquid sealing of the outer cap for sucking the atmosphere in the outer cap. Pressurized air is sent through the air supply pipe, to lower the water level of the coolants in the outer cap and the water level monitoring pipe sucks the pressurized air, by which the inside and the outside of the channel box are partitioned. Subsequently, if the sample water is sampled by a sampling tube, sampling water which enables accurate evaluation for radioactivity concentration in the fuel assembly can be obtained. (I.S.)

Decontamination of chlorantraniliprole residues on cabbage and cauliflower through household processing methods.

Science.gov (United States)

Kar, Abhijit; Mandal, Kousik; Singh, Balwinder

2012-04-01

A supervised field trial was conducted to study the residues of chlorantraniliprole on cabbage and cauliflower. Three applications of chlorantraniliprole at 10 days interval were made @ 9.25 and 18.50 g a.i. ha(-1). The samples of marketable size heads and curds of cabbage and cauliflower were collected at 0 and 1 day after the last application. QuEChERS sample preparation was used for the determination of chlorantraniliprole residues on cabbage heads and cauliflower curds. The residues of chlorantraniliprole were quantified by high performance liquid chromatography (HPLC) with photo diode array (PDA) detector and confirmed by high performance thin layer chromatography (HPTLC). Washing of cabbage and cauliflower with tap water removed about 17%-40% of chlorantraniliprole residues. However, boiling removed 100% of chlorantraniliprole residues on cabbage and cauliflower in both the cases.

Spectrophotometric Determination of Boron in Environmental Water Samples

International Nuclear Information System (INIS)

San San; Khin Win Kyi; Kwaw Naing

2002-02-01

The present paper deals with the study on the methods for the determination of boron in the environmental water samples. The standard methods which are useful for this determination are discussed thoroughly in this work. Among the standard methods approved by American Public Health Association, the carmine method was selected for this study. Prior to the determination of boron in the water samples, the precision and accuracy of the methods of choice were examined by using standard boron solutions. The determination of Boron was carried out by using water samples, waste water from Aquaculture Research Centre, University of Yangon, the Ayeyarwady River water near Magway Myathalon Pagoda in Magway Division, ground water from Sanchaung Township, and tap water from Universities' Research Centre, University of Yangon. Analyses of these water samples were done and statistical treatment of the results was carried out. (author)

Effect of thermal exposure on the residual stress relaxation in a hardened cylindrical sample under creep conditions

Science.gov (United States)

Radchenko, V. P.; Saushkin, M. N.; Tsvetkov, V. V.

2016-05-01

This paper describes the effect of thermal exposure (high-temperature exposure) ( T = 675°C) on the residual creep stress relaxation in a surface hardened solid cylindrical sample made of ZhS6UVI alloy. The analysis is carried out with the use of experimental data for residual stresses after micro-shot peening and exposures to temperatures equal to T = 675°C during 50, 150, and 300 h. The paper presents the technique for solving the boundary-value creep problem for the hardened cylindrical sample with the initial stress-strain state under the condition of thermal exposure. The uniaxial experimental creep curves obtained under constant stresses of 500, 530, 570, and 600 MPa are used to construct the models describing the primary and secondary stages of creep. The calculated and experimental data for the longitudinal (axial) tensor components of residual stresses are compared, and their satisfactory agreement is determined.

Multi-residue analysis method for analysis of pharmaceuticals using liquid chromatography-time of flight/mass spectrometry (LC-TOF/MS) in water sample

Science.gov (United States)

Al-Qaim, Fouad Fadhil; Abdullah, Md Pauzi; Othman, Mohamed Rozali

2013-11-01

In this work, a developed method using solid - phase extraction (SPE) followed by liquid chromatography - time of flight mass spectrometry (LC-ESI-TOF/MS) was developed and validated for quantification and confirmation of eleven pharmaceuticals with different therapeutic classes in water samples, Malaysia. These compounds are caffeine (CAF), prazosin (PRZ), enalapril (ENL), carbamazepine (CBZ), nifedipine (NFD), levonorgestrel (LNG), simvastatin (SMV), hydrochlorothiazide (HYD), gliclazide (GLIC), diclofenac-Na (DIC-Na) and mefenamic acid (MEF). LC was performed on a Dionex Ultimate 3000/LC 09115047 (USA) system. Chromatography was performed on a Thermo Scientific C18 (250 mm × 2.1 mm, i.d.: 5μm) column. Several parameters were optimised such as; mobile phase, gradient elution, collision energy and solvent elution for extraction of compounds from water. The recoveries obtained ranged from 30-148 % in river water. Five pharmaceutical compounds were detected in the surface water samples: caffeine, prazosin, enalpril, diclofenac-Na and mefenamic acid. The developed method is precise and accepted recoveries were got. In addition, this method is suitable to identify and quantify trace concentrations of pharmaceuticals in surface water.

Remediation of deltamethrin contaminated cotton fields: residual and adsorption assessment

Directory of Open Access Journals (Sweden)

Rafique Uzaira

2016-01-01

Full Text Available Pakistan occupies a significant global position in the growing of high quality cotton. The extensive application of pesticides on agricultural products leads to environmental risk due to toxic residues in air, water and soil. This study examined the chemodynamic effect of Deltamethrin on cotton fields. Samples were collected from the cotton fields of D.G. Khan, Pakistan and analyzed for heavy metal speciation patterns. Batch experiments were administered in order to study the adsorption of Deltamethrin in cotton fields. The effect of different factors including pH, adsorbate dose, and adsorbent mass on adsorption were studied. It was observed that in general, adsorption increased with increases in the mass of adsorbate, although the trends were irregular. Residual fractions of deltamethrin in the soil and water of cotton fields were analyzed to assess concentrations of xenobiotics bound to soil particles. Results indicated that such residues are significantly higher in soil samples due to high Koc in comparison to water, indicating the former is an efficient degradation agent. Results from the batch experiment resulted in 95% removal with alkaline pH and an adsorbent-adsorbate ratio of 250:1. These results may be used to environment friendly resource management policies.

Food safety in Thailand 2: Pesticide residues found in Chinese kale (Brassica oleracea), a commonly consumed vegetable in Asian countries

International Nuclear Information System (INIS)

Wanwimolruk, Sompon; Kanchanamayoon, Onnicha; Phopin, Kamonrat; Prachayasittikul, Virapong

2015-01-01

There is increasing public concern over human health risks associated with extensive use of pesticides in agriculture. Regulation of pesticide maximum residue limits (MRLs) in food commodities is established in many developed countries. For Thailand, this regulation exists in law but is not fully enforced. Therefore, pesticide residues in vegetables and fruits have not been well monitored. This study investigated the pesticide residues in Chinese kale, a commonly eaten vegetable among Asians. The Chinese kale samples (N = 117) were purchased from markets in Nakhon Pathom Province, Thailand, and analyzed for the content of 28 pesticides. Analysis was performed by the multiresidual extraction followed by GC–MS/MS. Of pesticides investigated, 12 pesticides were detected in 85% of the Chinese kale samples. Although carbaryl, deltamethrin, diazinon, fenvalerate and malathion were found in some samples, their levels were lower than their MRLs. However, in 34 samples tested, either carbofuran, chlorpyrifos, chlorothalonil, cypermethrin, dimethoate, metalaxyl or profenofos was detected exceeding their MRLs. This represents a 29% rate of pesticide detection above the MRL; a rate much higher than in developed countries. Washing vegetables under running water significantly reduced (p < 0.05) profenofos residues by 55%. The running water method did not significantly decrease cypermethrin residues in the samples but washing with vinegar did. Our research suggests that routine monitoring of pesticide residues is necessary to reduce the public health risks associated with eating contaminated vegetables. Washing vegetables before consumption is advisable as this helps to reduce the level of pesticide residues in our daily intake. - Highlights: • Significant pesticide residues were detected in Chinese kale sold in Thailand. • MRL exceedance was found and this was higher than that seen in developed countries. • Washing vegetables under running water can remove pesticide

Food safety in Thailand 2: Pesticide residues found in Chinese kale (Brassica oleracea), a commonly consumed vegetable in Asian countries

Energy Technology Data Exchange (ETDEWEB)

Wanwimolruk, Sompon, E-mail: sompon-999@hotmail.com [Center for Innovation Development and Technology Transfer, Faculty of Medical Technology, Mahidol University, Bangkok 10700 (Thailand); Kanchanamayoon, Onnicha [Center for Innovation Development and Technology Transfer, Faculty of Medical Technology, Mahidol University, Bangkok 10700 (Thailand); Phopin, Kamonrat [Center for Innovation Development and Technology Transfer, Faculty of Medical Technology, Mahidol University, Bangkok 10700 (Thailand); Department of Clinical Microbiology and Applied Technology, Faculty of Medical Technology, Mahidol University, Bangkok 10700 (Thailand); Prachayasittikul, Virapong [Department of Clinical Microbiology and Applied Technology, Faculty of Medical Technology, Mahidol University, Bangkok 10700 (Thailand)

2015-11-01

There is increasing public concern over human health risks associated with extensive use of pesticides in agriculture. Regulation of pesticide maximum residue limits (MRLs) in food commodities is established in many developed countries. For Thailand, this regulation exists in law but is not fully enforced. Therefore, pesticide residues in vegetables and fruits have not been well monitored. This study investigated the pesticide residues in Chinese kale, a commonly eaten vegetable among Asians. The Chinese kale samples (N = 117) were purchased from markets in Nakhon Pathom Province, Thailand, and analyzed for the content of 28 pesticides. Analysis was performed by the multiresidual extraction followed by GC–MS/MS. Of pesticides investigated, 12 pesticides were detected in 85% of the Chinese kale samples. Although carbaryl, deltamethrin, diazinon, fenvalerate and malathion were found in some samples, their levels were lower than their MRLs. However, in 34 samples tested, either carbofuran, chlorpyrifos, chlorothalonil, cypermethrin, dimethoate, metalaxyl or profenofos was detected exceeding their MRLs. This represents a 29% rate of pesticide detection above the MRL; a rate much higher than in developed countries. Washing vegetables under running water significantly reduced (p < 0.05) profenofos residues by 55%. The running water method did not significantly decrease cypermethrin residues in the samples but washing with vinegar did. Our research suggests that routine monitoring of pesticide residues is necessary to reduce the public health risks associated with eating contaminated vegetables. Washing vegetables before consumption is advisable as this helps to reduce the level of pesticide residues in our daily intake. - Highlights: • Significant pesticide residues were detected in Chinese kale sold in Thailand. • MRL exceedance was found and this was higher than that seen in developed countries. • Washing vegetables under running water can remove pesticide

Comparison of Methods for Bifenthrin Residues Determination in Fermented Wheat Samples

Directory of Open Access Journals (Sweden)

Tijana Đorđević

2012-01-01

Full Text Available Efficiency of three different sample preparation methods for GC/MS determinationof bifenthrin residues in wheat (Triticum spelta samples fermented by Lactobacillusplantarum was tested. The first method was based on a methanol:acetone=1:1 extractionfolowed by a purification on columns containing mixture of aluminium oxide and activatedcharcoal slurry-packed and eluted with dichlormethane, the second was based onmethanol:acetone=1:1 extraction folowed by the purification on florisil column and elutionby ethil acetate:acetone=4:1, while the third tested method was based on a combinationof the first two mentioned methods, thus methanol:acetone=1:1 extraction and clean-upthrought columns filled with a mixture of aluminum oxide and activated charcoal slurrypackedand eluted with ethil acetate:acetone=4:1. The second method was the most effectivefor obtaining satisfactory recoveries for bifenthrin in a range of 79-83% for four fortificationlevels, with good reproducibility i.e. RSD% in a range of 2.2-7.4%. The chosen methodwas further optimized by assessing the optimum volume of elution solvent used duringthe clean-up procedures. The highest recovery of 82.1% was obtained after elution with25 ml of solvent. Overall, two-step extraction with 25 ml of methanol:acetone=1:1 solventmix for 30 min, followed by clean-up procedure through a glass column with florisil coupledwith elution with 25 ml of ethyl acetate: acetone=4:1, allows simple, efficient and reliableGC/MS detection of bifenthrin residues from wheat grain fermented by L. plantarum.

Application of dispersive Liquid-Liquid microextraction based on solidification of floating organic droplet multi-residue method for the simultaneous determination of polychlorinated biphenyls, organochlorine, and pyrethroid pesticides in aqueous sample

International Nuclear Information System (INIS)

Zuo, Mei; Li, Man-Liang; Cheng, Jing; Matsadiq, Guzalnur; Liu, Lu; Zhang, Miao

2012-01-01

Dispersive liquid-liquid microextraction based on solidification of floating organic droplet (DLLME-SFO) technique was successfully applied for simultaneous assay of eight polychlorinated biphenyls, two organochlorine, and four pyrethroid pesticides multi-residue in aqueous samples by using GC-electron capture detection. The effects of various parameters such as kind of extractant and dispersant and volume of them, extraction time, effect of salt addition, and pH were optimized. As a result, 5.0 μL 1-dodecanol was chosen as extraction solvent, 600 μL methanol were used as dispersive solvent without salt addition, pH was adjusted to 7. Under the optimized conditions, the limits of detection (LOD) were ranged from 1.4 to 8.3 ng L -1 . Satisfactory linear range was observed from 5.0 to 2000 ng L -1 with correlation coefficient better than 0.9909. Good precisions were also acquired with RSD better than 13.6% for all target analytes. The enrichment factors of the method were ranged from 786 to 1427. The method can be successfully applied to simultaneous separation and determination of three class residues in real water samples and good recoveries were obtained ranging from 76 to 130, 73 to 129, and 78 to 130% for tap water, lake water, and industrial waste water, respectively. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

A survey of residual analysis and a new test of residual trend.

Science.gov (United States)

McDowell, J J; Calvin, Olivia L; Klapes, Bryan

2016-05-01

A survey of residual analysis in behavior-analytic research reveals that existing methods are problematic in one way or another. A new test for residual trends is proposed that avoids the problematic features of the existing methods. It entails fitting cubic polynomials to sets of residuals and comparing their effect sizes to those that would be expected if the sets of residuals were random. To this end, sampling distributions of effect sizes for fits of a cubic polynomial to random data were obtained by generating sets of random standardized residuals of various sizes, n. A cubic polynomial was then fitted to each set of residuals and its effect size was calculated. This yielded a sampling distribution of effect sizes for each n. To test for a residual trend in experimental data, the median effect size of cubic-polynomial fits to sets of experimental residuals can be compared to the median of the corresponding sampling distribution of effect sizes for random residuals using a sign test. An example from the literature, which entailed comparing mathematical and computational models of continuous choice, is used to illustrate the utility of the test. © 2016 Society for the Experimental Analysis of Behavior.

UMTRA project water sampling and analysis plan, Maybell, Colorado

International Nuclear Information System (INIS)

1994-06-01

This water sampling and analysis plan (WSAP) describes planned water sampling activities and provides the regulatory and technical basis for ground water sampling in 1994 at the US Department of Energy's (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site in Maybell, Colorado. The WSAP identifies and justifies sampling locations, analytical parameters, and sampling frequencies at the site. The ground water data will be used for site characterization and risk assessment. The regulatory basis for the ground water and surface water monitoring activities is derived from the EPA regulations in 40 CFR Part 192 (1993) and the proposed EPA standards of 1987 (52 FR 36000). Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), the Technical Approach Document (TAD) (DOE, 1989), and the most effective technical approach for the site. This WSAP also includes a summary and the results of water sampling activities from 1989 through 1992 (no sampling was performed in 1993)

Sampling art for ground-water monitoring wells in nuclide migration

International Nuclear Information System (INIS)

Liu Wenyuan; Tu Guorong; Dang Haijun; Wang Xuhui; Ke Changfeng

2010-01-01

Ground-Water sampling is one of the key parts in field nuclide migration. The objective of ground-water sampling program is to obtain samples that are representative of formation-quality water. In this paper, the ground-water sampling standards and the developments of sampling devices are reviewed. We also designed the sampling study projects which include the sampling methods, sampling parameters and the elementary devise of two types of ground-Water sampling devices. (authors)

Assessment of persistence and residue of diazinon and malathion in three rivers (Mond, Shahpour and Dalaky of Bushehr Province 2004-2005

Directory of Open Access Journals (Sweden)

Mansooreh Shayeghi

2007-09-01

Full Text Available Background: Water contamination due to insecticides, often generates dangerous results for consumers. Immoderate consumption of insecticides in neighboring farms contaminates rivers. Assessment of residue of phosphorus insecticides which are used in farms near rivers can play a key role in preventing probable poisonings and aquatic ecosystems polution. Methods: In this case control study, water of three permanent rivers in Bushehr province and urban water pipe network of Bushehr city were assessed in different months in 2004-2005 and 216 samples were collected on the whole. In each river,three stations were used for sampling. After the sampling, extraction processes were accomplished using solvents such as: acetone, methylen-chloride and benzene. For detection and measurement of TLC Scanner apparatus was used. Results: Residues of diazinon and malathion were found in water of the three rivers in spring and summer. And in other seasons the rate of residues were very low or zero. The statistical analysis of the results through one-sidedanalysis variance, showed that diazinon and malathion residues in the water of the surveyed rivers in different months had significant difference (p 0.05, while malathion residue was significant (p <0.05. Conclusion: In the first and second months after applying the two insecticides, their residues level in all three rivers of Mond, Shahpour and Dalaky are more than acceptable contamination level, the higher levels belong to diazinon. Precautions must be considered in using the water for drinking purposes and also using aquatic foods which are provided from these rivers.

Natural Radioactivity Pattern of Surabaya Water Environmental Samples

International Nuclear Information System (INIS)

Rosidi; Agus Taftazani

2007-01-01

The gross β radioactivity and natural radionuclide of Surabaya environmental samples pattern have been evaluated. The environmental samples were chosen randomly at 12 locations. The environment samples were water (fresh, estuary and coastal), sediment, eichhornia crassipes (Mart) Solms, Mangrove (Rhizophora stylosa), (Moolgarda delicatus) fish and (Johnius (Johnieops) borneensis) (Sharpnose hammer croaker) fish. The water sample was evaporated; the sediment sample was dried and ground; the biotic samples was burnt at the temperature 500 °C ; The gross β measurement using GM detector and the radionuclides has been identified by γ spectrometer. From the investigation results could be concluded that the natural radioactivity of environmental samples was very low. gross-β of water samples were lower than the threshold value of local government regulation of Surabaya no: 2 year 2004 (1 Bq/L). The distribution of gross-β activity of eichhornia crassipes (Mart) Solms was higher than the other biotic, water and sediment samples as well as the accumulation of radionuclides in the water organism was taken place. The result of identification using γ spectrometer has detected 7 of radionuclides, i.e 210 Pb, 212 Pb, 214 Pb, 208 Tl, 214 Bi, 228 Ac, and 40 K in all sample. The distribution factor of sediment F D was less than bioaccumulation factor of biotic F B and it indicates that there the radionuclide accumulation migration follows the pattern of water - sediment - biotic sample. (author)

UMTRA project water sampling and analysis plan, Naturita, Colorado

International Nuclear Information System (INIS)

1994-04-01

Surface remedial action is scheduled to begin at the Naturita UMTRA Project processing site in the spring of 1994. No water sampling was performed during 1993 at either the Naturita processing site (NAT-01) or the Dry Flats disposal site (NAT-12). Results of previous water sampling at the Naturita processing site indicate that ground water in the alluvium is contaminated as a result of uranium processing activities. Baseline ground water conditions have been established in the uppermost aquifer at the Dry Flats disposal site. Water sampling activities scheduled for April 1994 include preconstruction sampling of selected monitor wells at the processing site, surface water sampling of the San Miguel River, sampling of several springs/seeps in the vicinity of the disposal site, and sampling of two monitor wells in Coke Oven Valley. The monitor well locations provide sampling points to characterize ground water quality and flow conditions in the vicinity of the sites. The list of analytes has been updated to reflect constituents related to uranium processing activities and the parameters needed for geochemical evaluation. Water sampling will be conducted annually at minimum during the period of construction activities

Catch me if you can: Comparing ballast water sampling skids to traditional net sampling

Science.gov (United States)

Bradie, Johanna; Gianoli, Claudio; Linley, Robert Dallas; Schillak, Lothar; Schneider, Gerd; Stehouwer, Peter; Bailey, Sarah

2018-03-01

With the recent ratification of the International Convention for the Control and Management of Ships' Ballast Water and Sediments, 2004, it will soon be necessary to assess ships for compliance with ballast water discharge standards. Sampling skids that allow the efficient collection of ballast water samples in a compact space have been developed for this purpose. We ran 22 trials on board the RV Meteor from June 4-15, 2015 to evaluate the performance of three ballast water sampling devices (traditional plankton net, Triton sampling skid, SGS sampling skid) for three organism size classes: ≥ 50 μm, ≥ 10 μm to Natural sea water was run through the ballast water system and untreated samples were collected using paired sampling devices. Collected samples were analyzed in parallel by multiple analysts using several different analytic methods to quantify organism concentrations. To determine whether there were differences in the number of viable organisms collected across sampling devices, results were standardized and statistically treated to filter out other sources of variability, resulting in an outcome variable representing the mean difference in measurements that can be attributed to sampling devices. These results were tested for significance using pairwise Tukey contrasts. Differences in organism concentrations were found in 50% of comparisons between sampling skids and the plankton net for ≥ 50 μm, and ≥ 10 μm to < 50 μm size classes, with net samples containing either higher or lower densities. There were no differences for < 10 μm organisms. Future work will be required to explicitly examine the potential effects of flow velocity, sampling duration, sampled volume, and organism concentrations on sampling device performance.

Analytical procedures for determining Pb and Sr isotopic compositions in water samples by ID-TIMS

Directory of Open Access Journals (Sweden)

Veridiana Martins

2008-01-01

Full Text Available Few articles deal with lead and strontium isotopic analysis of water samples. The aim of this study was to define the chemical procedures for Pb and Sr isotopic analyses of groundwater samples from an urban sedimentary aquifer. Thirty lead and fourteen strontium isotopic analyses were performed to test different analytical procedures. Pb and Sr isotopic ratios as well as Sr concentration did not vary using different chemical procedures. However, the Pb concentrations were very dependent on the different procedures. Therefore, the choice of the best analytical procedure was based on the Pb results, which indicated a higher reproducibility from samples that had been filtered and acidified before the evaporation, had their residues totally dissolved, and were purified by ion chromatography using the Biorad® column. Our results showed no changes in Pb ratios with the storage time.

Magnetic solid-phase extraction of tetracyclines using ferrous oxide coated magnetic silica microspheres from water samples.

Science.gov (United States)

Lian, Lili; Lv, Jinyi; Wang, Xiyue; Lou, Dawei

2018-01-26

A novel magnetic solid-phase extraction approach was proposed for extraction of potential residues of tetracyclines (TCs) in tap and river water samples, based on Fe 3 O 4 @SiO 2 @FeO magnetic nanocomposite. Characterized results showed that the received Fe 3 O 4 @SiO 2 @FeO had distinguished magnetism and core-shell structure. Modified FeO nanoparticles with an ∼5 nm size distribution were homogeneously dispersed on the surface of the silica shell. Owing to the strong surface affinity of Fe (II) toward TCs, the magnetic nanocomposite could be applied to efficiently extract three TCs antibiotics, namely, oxytetracycline, tetracycline and chlortetracycline from water samples. Several factors, such as sorbent amount, pH condition, adsorption and desorption time, desorption solvent, selectivity and sample volume, influencing the extraction performance of TCs were investigated and optimized. The developed method showed excellent linearity (R > 0.9992) in the range of 0.133-333 μg L -1 , under optimized conditions. The limits of detection were between 0.027 and 0.107 μg L -1 for oxytetracycline, tetracycline and chlortetracycline, respectively. The feasibility of this method was evaluated by analysis of tap and river water samples. The recoveries at the spiked concentration levels ranged from 91.0% to 104.6% with favorable reproducibility (RSD < 4%). Copyright © 2017 Elsevier B.V. All rights reserved.

Advances in Radiocarbon Measurement of Water Samples

Energy Technology Data Exchange (ETDEWEB)

Janovics, R.; Molnar, M.; Major, I. [Institute of Nuclear Research (ATO MKI), Hungarian Academy of Sciences, H-4001 Debrecen (Hungary); Svetlik, I. [Department of Radiation Dosimetry, Nuclear Physics Institute AS CR, Prague (Czech Republic); Wacker, L. [Institute for Particle Physics, ETH Hoenggerberg, Zuerich (Switzerland)

2013-07-15

In this paper two very different and novel methods for the {sup 14}C measurement of water samples are presented. The first method uses direct absorption into a scintillation cocktail and a following liquid scintillation measurement. Typical sample size is 20-40 L and overall uncertainty is {+-} 2% for modern samples. It is a very cost effective and easy to use method based on a novel and simple static absorption process for the CO{sub 2} extracted from groundwater. The other very sensitive method is based on accelerator mass spectrometry (AMS) using a gas ion source. With a MICADAS type AMS system we demonstrated that you can routinely measure the {sup 14}C content of 1 mL of water sample with better than 1% precision (for a modern sample). This direct {sup 14}C AMS measurement of water takes less than 20 minutes including sample preparation. (author)

Separation tests of heavy metals in samples of industrial wastes through flotation

International Nuclear Information System (INIS)

Abrego L, J.

1995-12-01

Samples of residual muds, taken at the exit of the filter-press of the water treatment plant of a galvanoplastics industry in Lerma, Estado de Mexico, its were prepared for its qualitative and quantitative analysis. Likewise, the residual waters of the cistern located at the end of the electrodeposition process, was subjected to qualitative chemical analysis for the neutron activation technique and to quantitative analysis by atomic absorption spectrometry. The samples were treated by a flotation process by means of the one which it was studied the heavy metals removal. The results show that the AP-845 collector is the one that better it fulfilled the objectives since, it solves the problem, unless by the copper that although their concentration in the residual waters drop a lot, it was not inside the standard. (Author)

Gas-driven pump for ground-water samples

Science.gov (United States)

Signor, Donald C.

1978-01-01

Observation wells installed for artificial-recharge research and other wells used in different ground-water programs are frequently cased with small-diameter steel pipe. To obtain samples from these small-diameter wells in order to monitor water quality, and to calibrate solute-transport models, a small-diameter pump with unique operating characteristics is required that causes a minimum alternation of samples during field sampling. A small-diameter gas-driven pump was designed and built to obtain water samples from wells of two-inch diameter or larger. The pump is a double-piston type with the following characteristics: (1) The water sample is isolated from the operating gas, (2) no source of electricity is ncessary, (3) operation is continuous, (4) use of compressed gas is efficient, and (5) operation is reliable over extended periods of time. Principles of operation, actual operation techniques, gas-use analyses and operating experience are described. Complete working drawings and a component list are included. Recent modifications and pump construction for high-pressure applications also are described. (Woodard-USGS)

Kape barako (coffea liberica) grounds as adsorbent for the removal of lead in lead-enriched Marikina river water samples

International Nuclear Information System (INIS)

Valera, Florenda S.; Garcia, Jhonard John L.

2015-01-01

Kape Barako (Coffee liberica) grounds (residue left after brewing ground coffee) were used as adsorbent for the removal of lead in Marikina River water samples. The sundried coffee grounds showed 9.30% moisture after drying in the oven. The coffee grounds were determined using Shimadzu AA-6501S Atomic Adsorption Spectrometer. The lead concentration was determined to be 4.7 mg/kg in coffee grounds and below detection limit in the Marikina River water samples. The adsorption studies were done at room temperature, and the optimized parameters were a contact time of 3 hours, an adsorbent dose of 3.0 g/L and 4.0 mg/L Pb-enriched water samples. The maximum uptake capacity was found to be 14.2 mg of lead/g adsorbent. The adsorption studies were done at room temperature, and the optimized parameters were a contact time of 3 hours, an adsorbent dose of 3.0 g/L and 4.0 mg/L Pb-enriched water samples. Analyses of the coffee grounds before and after lead adsorption using Shimadzu IR-Affinity-I Fourier Transform Infrared Spectrometer showed marked difference in the spectra, indicating interaction between Pb and the functional groups of the coffee grounds. (author)

Sample container and storage for paclobutrazol monitoring in irrigation water

Science.gov (United States)

Paclobutrazol is a plant growth retardant commonly used on greenhouse crops. Residues from paclobutrazol applications can accumulate in recirculated irrigation water. Given that paclobutrazol has a long half-life and potential biological activity in parts per billion concentrations, it would be de...

Pesticide management and their residues in sediments and surface and drinking water in the Mekong Delta, Vietnam.

Science.gov (United States)

Toan, Pham Van; Sebesvari, Zita; Bläsing, Melanie; Rosendahl, Ingrid; Renaud, Fabrice G

2013-05-01

Public concern in Vietnam is increasing with respect to pesticide pollution of the environment and of drinking water resources. While established monitoring programs in the Mekong Delta (MD) focus on the analysis of organochlorines and some organophosphates, the environmental concentrations of more recently used pesticides such as carbamates, pyrethroides, and triazoles are not monitored. In the present study, household level pesticide use and management was therefore surveyed and combined with a one year environmental monitoring program of thirteen relevant pesticides (buprofezin, butachlor, cypermethrin, α-endosulfan, β-endosulfan, endosulfan-sulfate, fenobucarb, fipronil, isoprothiolane, pretilachlor, profenofos, propanil, and propiconazole) in surface water, soil, and sediment samples. The surveys showed that household level pesticide management remains suboptimal in the Mekong Delta. As a consequence, a wide range of pesticide residues were present in water, soil, and sediments throughout the monitoring period. Maximum concentrations recorded were up to 11.24 μg l(-1) in water for isoprothiolane and up to 521 μg kg(-1) dm in sediment for buprofezin. Annual average concentrations ranged up to 3.34 μg l(-1) in water and up to 135 μg kg(-1) dm in sediment, both for isoprothiolane. Occurrence of pesticides in the environment throughout the year and co-occurrence of several pesticides in the samples indicate a considerable chronic exposure of biota and humans to pesticides. This has a high relevance in the delta as water for drinking is often extracted from canals and rivers by rural households (GSO, 2005, and own surveys). The treatment used by the households for preparing surface water prior to consumption (flocculation followed by boiling) is insufficient for the removal of the studied pesticides and boiling can actually increase the concentration of non-volatile pollutants. Copyright © 2012 Elsevier B.V. All rights reserved.

An investigation into the effects of residual water on the glass transition temperature of polylactide microspheres using modulated temperature DSC.

Science.gov (United States)

Passerini, N; Craig, D Q

2001-05-18

The objective of the study was to ascertain residual water levels in polylactide and polylactide-co-glycolide microspheres prepared using the solvent evaporation technique and to investigate the effects of that water on the glass transitional behaviour of the microspheres. Microspheres were prepared from polylactic acid (PLA) and polylactide-co-glycolide (PLGA) 50:50 and 75:25 using a standard solvent evaporation technique. The glass transition was measured as a function of drying conditions using modulated temperature DSC. The microspheres were found to contain very low levels of dichloromethane, while residual water levels of up to circa 3% w/w were noted after freeze or oven drying, these levels being higher for microspheres containing higher glycolic acid levels. The residual water was found to lower the T(g) following the Gordon-Taylor relationship. The data indicate that the microparticles may retain significant water levels following standard preparation and drying protocols and that this drying may markedly lower the T(g) of the spheres.

The Effect of Washing and Peeling on Reduction of Dithiocarbamates Residues in Cucumber and Tomato

Directory of Open Access Journals (Sweden)

Mohammad Reza Mehrasebi

2016-03-01

Full Text Available Background: Dithiocarbamates, the main group of fungicides, are used to control about 400 pathogens in more than 70 crops. These pesticides are widely applied to crops including potato, cereal, apple, pear and leafy vegetables throughout the world since 1960. From the late 1980s, using these fungicides has caused much debate among regulators about their long-term effects on consumers and occupational users. Method: In this study the residues of Dithiocarbamates in cucumber and tomato using the colorimetric method (Keppel method was measured. Respectively 80 and 45 samples of greenhouse cucumber and tomato were collected from Zanjan vegetables center in autumns and winter 2013. The samples were analyzed in 4 treatments of: unwashed, washing with water, washing whit detergent and peeling. Result: The results showed that the average concentration of Dithiocarbamates residues in unwashed greenhouse cucumber and tomatoes were 384.5 µg/kg and 65 µg/kg respectively. 35% and 5% of unwashed and water washed cucumber and tomato samples (respectively had higher Dithiocarbamates residue than MRL recommended by Institute of Standards and Industrial Research of Iran (0.5mg/kg. Conclusion: The treatments of washing and peeling had significant effect on the reduction of Dithiocarbamates residues in the all samples.

Radon in water samples around Ningyo Toge area

Energy Technology Data Exchange (ETDEWEB)

Furuta, Sadaaki [Power Reactor and Nuclear Fuel Development Corp., Kamisaibara, Okayama (Japan). Ningyo Toge Works

1997-02-01

Radon concentrations of river water and drinking water were surveyed. Water samples were collected from the region around Ningyo-Toge Works which were positioned on a granitic layer having uranium deposit. Each sample was taken using a separating funnel and the radioactivity was counted by liquid scintillation counter (ALOKA, LB-2). Since there were old working places of mine in the region, mine drainages from them were also analyzed. The radon concentration of drinking water from the region ranged from 0.1 to 230 Bq/l. The samples with a higher activity than 100 Bq/l were water from springs or wells and the area of the highest Rn concentration was on a typical granitic layer, suggesting some geographic effects on Rn concentration. Some samples of drinking water had slightly higher levels of Rn, probably due to the utilization of underflow as its source. The mean concentration of Rn became higher in the order; river water, drinking water, mine drainage in the region. In addition, a negative correlation between Rn concentration of water and the river flow rate was observed in this region. (M.N.)

Water sample-collection and distribution system

Science.gov (United States)

Brooks, R. R.

1978-01-01

Collection and distribution system samples water from six designated stations, filtered if desired, and delivers it to various analytical sensors. System may be controlled by Water Monitoring Data Acquisition System or operated manually.

Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

Energy Technology Data Exchange (ETDEWEB)

Lombi, E., E-mail: enzo.lombi@unisa.edu.a [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Centre for Environmental Risk Assessment and Remediation, University of South Australia, Building X, Mawson Lakes Campus, Mawson Lakes, SA 5095 (Australia); CRC CARE, PO Box 486, Salisbury, SA 5106 (Australia); Stevens, D.P. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Arris Pty Ltd, PO Box 5143, Burnley, Victoria 3121 (Australia); McLaughlin, M.J. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Soil and Land Systems, University of Adelaide, PMB 1, Glen Osmond, SA 5064 (Australia)

2010-06-15

Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

International Nuclear Information System (INIS)

Lombi, E.; Stevens, D.P.; McLaughlin, M.J.

2010-01-01

Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

Quality-control design for surface-water sampling in the National Water-Quality Network

Science.gov (United States)

Riskin, Melissa L.; Reutter, David C.; Martin, Jeffrey D.; Mueller, David K.

2018-04-10

The data-quality objectives for samples collected at surface-water sites in the National Water-Quality Network include estimating the extent to which contamination, matrix effects, and measurement variability affect interpretation of environmental conditions. Quality-control samples provide insight into how well the samples collected at surface-water sites represent the true environmental conditions. Quality-control samples used in this program include field blanks, replicates, and field matrix spikes. This report describes the design for collection of these quality-control samples and the data management needed to properly identify these samples in the U.S. Geological Survey’s national database.

Two-step microextraction combined with high performance liquid chromatographic analysis of pyrethroids in water and vegetable samples.

Science.gov (United States)

Mukdasai, Siriboon; Thomas, Chunpen; Srijaranai, Supalax

2014-03-01

Dispersive liquid microextraction (DLME) combined with dispersive µ-solid phase extraction (D-µ-SPE) has been developed as a new approach for the extraction of four pyrethroids (tetramethrin, fenpropathrin, deltamethrin and permethrin) prior to the analysis by high performance liquid chromatography (HPLC) with UV detection. 1-Octanol was used as the extraction solvent in DLME. Magnetic nanoparticles (Fe3O4) functionalized with 3-aminopropyl triethoxysilane (APTS) were used as the dispersive in DLME and as the adsorbent in D-µ-SPE. The extracted pyrethroids were separated within 30 min using isocratic elution with acetonitrile:water (72:28). The factors affecting the extraction efficiency were investigated. Under the optimum conditions, the enrichment factors were in the range of 51-108. Linearity was obtained in the range 0.5-400 ng mL(-1) (tetramethrin) and 5-400 ng mL(-1) (fenpropathrin, deltamethrin and permethrin) with the correlation coefficients (R(2)) greater than 0.995. Detection limits were 0.05-2 ng mL(-1) (water samples) and 0.02-2.0 ng g(-1) (vegetable samples). The relative standard deviations of peak area varied from 1.8 to 2.5% (n=10). The extraction recoveries of the four pyrethroids in field water and vegetable samples were 91.7-104.5%. The proposed method has high potential for use as a sensitive method for determination of pyrethroid residues in water and vegetable samples. Copyright © 2013 Elsevier B.V. All rights reserved.

The WIPP Water Quality Sampling Program

International Nuclear Information System (INIS)

Uhland, D.; Morse, J.G.; Colton, D.

1986-01-01

The Waste Isolation Pilot Plant (WIPP), a Department of Energy facility, will be used for the underground disposal of wastes. The Water Quality Sampling Program (WQSP) is designed to obtain representative and reproducible water samples to depict accurate water composition data for characterization and monitoring programs in the vicinity of the WIPP. The WQSP is designed to input data into four major programs for the WIPP project: Geochemical Site Characterization, Radiological Baseline, Environmental Baseline, and Performance Assessment. The water-bearing units of interest are the Culebra and Magneta Dolomite Members of the Rustler Formation, units in the Dewey Lake Redbeds, and the Bell Canyon Formation. At least two chemically distinct types of water occur in the Culebra, one being a sodium/potassium chloride water and the other being a calcium/magnesium sulfate water. Water from the Culebra wells to the south of the WIPP site is distinctly fresher and tends to be of the calcium/magnesium sulfate type. Water in the Culebra in the north and around the WIPP site is distinctly fresher and tends to be of the sodium/potassium chloride type and is much higher in total dissolved solids. The program, which is currently 1 year old, will continue throughout the life of the facility as part of the Environmental Monitoring Program

Validation of single-sample doubly labeled water method

International Nuclear Information System (INIS)

Webster, M.D.; Weathers, W.W.

1989-01-01

We have experimentally validated a single-sample variant of the doubly labeled water method for measuring metabolic rate and water turnover in a very small passerine bird, the verdin (Auriparus flaviceps). We measured CO 2 production using the Haldane gravimetric technique and compared these values with estimates derived from isotopic data. Doubly labeled water results based on the one-sample calculations differed from Haldane values by less than 0.5% on average (range -8.3 to 11.2%, n = 9). Water flux computed by the single-sample method differed by -1.5% on average from results for the same birds based on the standard, two-sample technique (range -13.7 to 2.0%, n = 9)

Sampling for Beryllium Surface Contamination using Wet, Dry and Alcohol Wipe Sampling

Energy Technology Data Exchange (ETDEWEB)

Kerr, Kent [Central Missouri State Univ., Warrensburg, MO (United States)

2004-12-01

This research project was conducted at the National Nuclear Security Administration's Kansas City Plant, operated by Honeywell Federal Manufacturing and Technologies, in conjunction with the Safety Sciences Department of Central Missouri State University, to compare relative removal efficiencies of three wipe sampling techniques currently used at Department of Energy facilities. Efficiencies of removal of beryllium contamination from typical painted surfaces were tested by wipe sampling with dry Whatman 42 filter paper, with water-moistened (Ghost Wipe) materials, and by methanol-moistened wipes. Test plates were prepared using 100 mm X 15 mm Pyrex Petri dishes with interior surfaces spray painted with a bond coat primer. To achieve uniform deposition over the test plate surface, 10 ml aliquots of solution containing 1 beryllium and 0.1 ml of metal working fluid were transferred to the test plates and subsequently evaporated. Metal working fluid was added to simulate the slight oiliness common on surfaces in metal working shops where fugitive oil mist accumulates over time. Sixteen test plates for each wipe method (dry, water, and methanol) were processed and sampled using a modification of wiping patterns recommended by OSHA Method 125G. Laboratory and statistical analysis showed that methanol-moistened wipe sampling removed significantly more (about twice as much) beryllium/oil-film surface contamination as water-moistened wipes (p< 0.001), which removed significantly more (about twice as much) residue as dry wipes (p <0.001). Evidence for beryllium sensitization via skin exposure argues in favor of wipe sampling with wetting agents that provide enhanced residue removal efficiency.

Residues of 14C-chlorpyrifos in coconut by radiotracer techniques

International Nuclear Information System (INIS)

Tejada, A.W.; Calumpang, S.M.F.; Magallona, E.D.

1992-01-01

A coconut tree was root-infused with 5 g a.i. chlorpyrifos (Lorsban plus 1.4 uCi of 14 C-chlorpyrifos. Coconut samples both young and mature, were taken 24 h up to 60 days after root infusion. Analysis of the meat and water was done. The maximum uptake of chlorpyrifos equivalents was on the 13th day after root infusion both in mature and young fruit. The residue in water reached the peak on the 20th day after infusion and declined thereafter. A preharvest interval (PHI) of more than 60 days maybe recommended for safe consumption. The usual practice of storing copra in treated warehouses until it is processed into oil was simulated in the laboratory to determine the residues absorbed on the meat. Forty kg of copra with moisture content of 7-12% were stored in an improvised warehouse, i.e. 1 m x 1.5 m x 1 m wooden box, which was treated with 100 ml 1% a.i. Lorsban 50 WP plus 100 uCi 14 C-chlorpyrifos for protection against insects. Analysis showed that 14 C-chlorpyrifos equivalents ranged from 22.6 mg/kg on the 30th day to 8.2 mg/kg on the 90th day with a 63.7% reduction in residues. Bound residues were detected on samples stored for 60-90 days, with levels of 1.0 to 0.2 ug/g 14 C-chlorpyrifos equivalents. This is within the Maximum Residue Limit of 2 mg/kg set by FAO/WHO for chlorpyrifos in most agricultural commodities. Chlorpyrifos residues were also determined at various stages of refining and processing of crude coconut oil. It was subjected to alkali refining, bleaching and finally steaming. The residues were reduced by as much as 32.7%. (author). 18 refs.; 2 figs.; 3 tabs

Multi-rate cubature Kalman filter based data fusion method with residual compensation to adapt to sampling rate discrepancy in attitude measurement system.

Science.gov (United States)

Guo, Xiaoting; Sun, Changku; Wang, Peng

2017-08-01

This paper investigates the multi-rate inertial and vision data fusion problem in nonlinear attitude measurement systems, where the sampling rate of the inertial sensor is much faster than that of the vision sensor. To fully exploit the high frequency inertial data and obtain favorable fusion results, a multi-rate CKF (Cubature Kalman Filter) algorithm with estimated residual compensation is proposed in order to adapt to the problem of sampling rate discrepancy. During inter-sampling of slow observation data, observation noise can be regarded as infinite. The Kalman gain is unknown and approaches zero. The residual is also unknown. Therefore, the filter estimated state cannot be compensated. To obtain compensation at these moments, state error and residual formulas are modified when compared with the observation data available moments. Self-propagation equation of the state error is established to propagate the quantity from the moments with observation to the moments without observation. Besides, a multiplicative adjustment factor is introduced as Kalman gain, which acts on the residual. Then the filter estimated state can be compensated even when there are no visual observation data. The proposed method is tested and verified in a practical setup. Compared with multi-rate CKF without residual compensation and single-rate CKF, a significant improvement is obtained on attitude measurement by using the proposed multi-rate CKF with inter-sampling residual compensation. The experiment results with superior precision and reliability show the effectiveness of the proposed method.

Compostagem da fração sólida da água residuária de suinocultura Solid fraction composting of residual water from pig farms

Directory of Open Access Journals (Sweden)

Marco A. P. Orrico Júnior

2009-09-01

Full Text Available Avaliar o desenvolvimento do processo de compostagem utilizando como substrato à fração sólida da água residuária de suinocultura foi o objetivo deste trabalho. Para a obtenção da fração sólida, a água residuária de suinocultura foi submetida ao peneiramento, utilizando-se de peneira com malha de 1 milímetro. Após separação, a fração sólida foi utilizada para a confecção de três leiras de compostagem, em pátio com piso de concreto e cobertura plástica. Durante a compostagem da fração sólida da água residuária de suinocultura, foram avaliados: temperatura, reduções de sólidos totais (ST, sólidos voláteis (SV, demanda química de oxigênio (DQO, carbono orgânico, matéria orgânica compostável (MOC, matéria orgânica resistente à compostagem (MORC, números mais prováveis (NMPs de coliformes totais e coliformes termotolerantes, além do volume e dos teores de nutrientes no composto. A compostagem mostrou-se eficiente no tratamento da fração sólida da água residuária de suinocultura devido à elevada minimização do poder poluente dos dejetos, observando-se reduções de 71,24% nos teores de ST, 64,55% no volume, 56,89% no teor de DQO e 56,89% na MOC. Foram verificadas reduções de 100% nos NMPs de coliformes totais e termotolerantes, o que possibilita seu uso como adubo orgânico.This work aimed to evaluate the development of the composting process by using the solid fraction of residual water from a pig farm. To obtain the solid fraction, the residual water was sewed in a 1mm screen sew. After separation, the solid fraction was used to form three composting piles, on a patio with concrete floor and plastic cover. During composting the solid fraction of residual water from pig farms was monitored: temperature, total solids reduction (TS, volatile solids (VS chemical demand for oxygen (CDO, organic carbon, compostable organic matter (COM, organic matter resistant to composting (OMRC, most probable

Evaluation of Membrane Ultrafiltration and Residual Chlorination as a Decentralized Water Treatment Strategy for Ten Rural Healthcare Facilities in Rwanda

Directory of Open Access Journals (Sweden)

Alexandra Huttinger

2015-10-01

Full Text Available There is a critical need for safe water in healthcare facilities (HCF in low-income countries. HCF rely on water supplies that may require additional on-site treatment, and need sustainable technologies that can deliver sufficient quantities of water. Water treatment systems (WTS that utilize ultrafiltration membranes for water treatment can be a useful technology in low-income countries, but studies have not systematically examined the feasibility of this technology in low-income settings. We monitored 22 months of operation of 10 WTS, including pre-filtration, membrane ultrafiltration, and chlorine residual disinfection that were donated to and operated by rural HCF in Rwanda. The systems were fully operational for 74% of the observation period. The most frequent reasons for interruption were water shortage (8% and failure of the chlorination mechanism (7%. When systems were operational, 98% of water samples collected from the HCF taps met World Health Organization (WHO guidelines for microbiological water quality. Water quality deteriorated during treatment interruptions and when water was stored in containers. Sustained performance of the systems depended primarily on organizational factors: the ability of the HCF technician to perform routine servicing and repairs, and environmental factors: water and power availability and procurement of materials, including chlorine and replacement parts in Rwanda.

Assessment of organochlorine pesticide residues in Atlantic Rain Forest fragments, Rio de Janeiro, Brazil

Energy Technology Data Exchange (ETDEWEB)

Soares Quinete, Natalia, E-mail: nataliaquinete@yahoo.com.br [Instituto Nacional de Tecnologia, Departamento de Quimica Analitica, Laboratorio de Quimica Analitica e Metrologia em Quimica, Av. Venezuela, 82 - Rio de Janeiro, RJ 20081-312 (Brazil); Santos de Oliveira, Elba dos [Instituto Nacional de Tecnologia, Departamento de Energia, Av. Venezuela, 82 - Rio de Janeiro, RJ 20081-312 (Brazil); Fernandes, Daniella R. [Universidade Federal do Rio de Janeiro, Instituto de Quimica, Departamento de Quimica Analitica, CT - Bloco A, Cidade Universitaria, 21941-909 - Rio de Janeiro (Brazil); Souza Avelar, Andre de [Universidade Federal do Rio de Janeiro, Departamento de Geografia, Instituto de Geociencias, CCMN, Bloco F, Cidade Universitaria, 21941-919 - Rio de Janeiro (Brazil); Erthal Santelli, Ricardo [Universidade Federal do Rio de Janeiro, Instituto de Quimica, Departamento de Quimica Analitica, CT - Bloco A, Cidade Universitaria, 21941-909 - Rio de Janeiro (Brazil)

2011-12-15

A superficial water quality survey in a watershed of the Paraiba do Sul River, the main water supply for the most populated cities of southeastern Brazil, was held in order to assess the impact of the expansion of agricultural activity in the near border of the Atlantic Rain Forest. The aim of this study was to investigate the presence of priority organochlorine pollutants in soils and superficial waters of Atlantic rainforest fragments in Teresopolis, Rio de Janeiro State. Soil sample preparations were compared by using ultrasound, microwave assisted extraction and Soxhlet extraction. Recoveries of matrix spiked samples ranged from 70 to 130%. Analysis of a certified soil material showed recoveries ranging from 71 to 234%. Although low concentrations of organochlorine residues were found in water and soil samples, this area is of environmental importance and concern, thus demanding a monitoring program of its compartments. - Highlights: > The organochlorine pollutants occurrence in the Atlantic Rain Forest was investigated. > PARNASO was considered a control area of environmental quality. > Extractions methods were compared for typical C-rich soils samples from Brazil. > Low concentrations of organochlorine residues were found in water and soil samples. > A monitoring program is demanded due to the environmental importance of the area. - The occurrence of organochlorine pollutants in soils of the Atlantic rainforest fragments in Rio de Janeiro, Brazil demands a monitoring program of its compartments.

Assessment of organochlorine pesticide residues in Atlantic Rain Forest fragments, Rio de Janeiro, Brazil

International Nuclear Information System (INIS)

Soares Quinete, Natalia; Santos de Oliveira, Elba dos; Fernandes, Daniella R.; Souza Avelar, Andre de; Erthal Santelli, Ricardo

2011-01-01

A superficial water quality survey in a watershed of the Paraiba do Sul River, the main water supply for the most populated cities of southeastern Brazil, was held in order to assess the impact of the expansion of agricultural activity in the near border of the Atlantic Rain Forest. The aim of this study was to investigate the presence of priority organochlorine pollutants in soils and superficial waters of Atlantic rainforest fragments in Teresopolis, Rio de Janeiro State. Soil sample preparations were compared by using ultrasound, microwave assisted extraction and Soxhlet extraction. Recoveries of matrix spiked samples ranged from 70 to 130%. Analysis of a certified soil material showed recoveries ranging from 71 to 234%. Although low concentrations of organochlorine residues were found in water and soil samples, this area is of environmental importance and concern, thus demanding a monitoring program of its compartments. - Highlights: → The organochlorine pollutants occurrence in the Atlantic Rain Forest was investigated. → PARNASO was considered a control area of environmental quality. → Extractions methods were compared for typical C-rich soils samples from Brazil. → Low concentrations of organochlorine residues were found in water and soil samples. → A monitoring program is demanded due to the environmental importance of the area. - The occurrence of organochlorine pollutants in soils of the Atlantic rainforest fragments in Rio de Janeiro, Brazil demands a monitoring program of its compartments.

Evaluation of Patterns and Spatial Trends of Pesticide Residues

African Journals Online (AJOL)

dell

PCA of the data sets for pesticide residues in water, soil and sediments samples from ..... J. Sci. 38(3), 2012. 189. 0.00. 0.20. 0.40. 0.60. 0.80. 1.00. Comp[1]. Comp[2]. R. 2. X. (c u m. ) & ..... Environmental Management, 60: 215-. 225. Wiberg K ...

Residual fluxes of salt and water in the Azhikode estuary, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Pylee, A.; Varma, P.U.; Revichandran, C.

hours at all stations and the data were analysed to provide estimates of the residual fluxes of water and salt. The interpolated data for the non-dimensional depth was used for computation of depth, tide and cross sectional averages. A net seaward flow...

A novel cryogenic treatment for reduction of residual stresses in 2024 aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Araghchi, M., E-mail: M.Araghchi@ma.iut.ac.ir [Department of Materials Engineering, Malek Ashtar University of Technology, Isfahan (Iran, Islamic Republic of); Mansouri, H.; Vafaei, R. [Department of Materials Engineering, Malek Ashtar University of Technology, Isfahan (Iran, Islamic Republic of); Guo, Yina [Bernal Institute, University of Limerick, Limerick (Ireland)

2017-03-24

Residual stresses induced during quenching of aluminum alloys cause distortion and have a negative effect on their properties. The purpose of this study is to reduce the residual stresses and improve mechanical properties by using a novel cryogenic treatment. Water quenched samples were cooled down by immersion in liquid nitrogen at −196 °C, following by rapid heating in hot oil at 180 °C and finally they were artificially aged. Residual stresses was measured by the hole drilling strain gauge method. The mechanical properties and microstructure of a heat treated samples were investigated by means of hardness measurements, tensile tests and transmission electron microscopy. The results showed that this treatment can relieve up to 71% of the residual stresses compared to 29% related to the traditional cryogenic treatment that used boiling water as the reheating medium. In addition, there is a considerable increase of about 75 MPa in the ultimate tensile strength in comparison to the T6 heat-treated alloy. TEM observations revealed that the S′ precipitates were fine and uniformly distributed in the microstructure due to deformation during reheating in hot oil.

Detection of Residual Levels and Associated Health Risk of Seven Pesticides in Fresh Eggplant and Tomato Samples from Narayanganj District, Bangladesh

Directory of Open Access Journals (Sweden)

Md. Nur Alam

2015-01-01

Full Text Available Residual levels of seven frequently used pesticides were investigated in 140 samples of two common vegetables, eggplants and tomatoes, from agricultural fields in the Narayanganj district of Bangladesh. The analysis of pesticide residues was performed by high-performance liquid chromatography with photodiode array detection. A large percentage of the eggplants (50% and tomatoes (60% from the Narayanganj district were contaminated with pesticides, and all of the levels were above the maximum residual limit (MRL proposed by the EC regulation. Diazinon was the most common (35% pesticide detected in the vegetable samples at a concentration of 45–450 times higher than the MRL. The health risk index for diazinon was highest for both eggplant and tomato samples, which may be due to its physiochemical properties. Fenitrothion and linuron are the two second most common types of pesticides detected in the vegetable samples. Regular monitoring of the use of common pesticides on vegetables should be conducted.

Properties of Soil Pore Space Regulate Pathways of Plant Residue Decomposition and Community Structure of Associated Bacteria

Science.gov (United States)

Negassa, Wakene C.; Guber, Andrey K.; Kravchenko, Alexandra N.; Marsh, Terence L.; Hildebrandt, Britton; Rivers, Mark L.

2015-01-01

Physical protection of soil carbon (C) is one of the important components of C storage. However, its exact mechanisms are still not sufficiently lucid. The goal of this study was to explore the influence of soil structure, that is, soil pore spatial arrangements, with and without presence of plant residue on (i) decomposition of added plant residue, (ii) CO2 emission from soil, and (iii) structure of soil bacterial communities. The study consisted of several soil incubation experiments with samples of contrasting pore characteristics with/without plant residue, accompanied by X-ray micro-tomographic analyses of soil pores and by microbial community analysis of amplified 16S–18S rRNA genes via pyrosequencing. We observed that in the samples with substantial presence of air-filled well-connected large (>30 µm) pores, 75–80% of the added plant residue was decomposed, cumulative CO2 emission constituted 1,200 µm C g-1 soil, and movement of C from decomposing plant residue into adjacent soil was insignificant. In the samples with greater abundance of water-filled small pores, 60% of the added plant residue was decomposed, cumulative CO2 emission constituted 2,000 µm C g-1 soil, and the movement of residue C into adjacent soil was substantial. In the absence of plant residue the influence of pore characteristics on CO2 emission, that is on decomposition of the native soil organic C, was negligible. The microbial communities on the plant residue in the samples with large pores had more microbial groups known to be cellulose decomposers, that is, Bacteroidetes, Proteobacteria, Actinobacteria, and Firmicutes, while a number of oligotrophic Acidobacteria groups were more abundant on the plant residue from the samples with small pores. This study provides the first experimental evidence that characteristics of soil pores and their air/water flow status determine the phylogenetic composition of the local microbial community and directions and magnitudes of soil C

Properties of soil pore space regulate pathways of plant residue decomposition and community structure of associated bacteria.

Science.gov (United States)

Negassa, Wakene C; Guber, Andrey K; Kravchenko, Alexandra N; Marsh, Terence L; Hildebrandt, Britton; Rivers, Mark L

2015-01-01

Physical protection of soil carbon (C) is one of the important components of C storage. However, its exact mechanisms are still not sufficiently lucid. The goal of this study was to explore the influence of soil structure, that is, soil pore spatial arrangements, with and without presence of plant residue on (i) decomposition of added plant residue, (ii) CO2 emission from soil, and (iii) structure of soil bacterial communities. The study consisted of several soil incubation experiments with samples of contrasting pore characteristics with/without plant residue, accompanied by X-ray micro-tomographic analyses of soil pores and by microbial community analysis of amplified 16S-18S rRNA genes via pyrosequencing. We observed that in the samples with substantial presence of air-filled well-connected large (>30 µm) pores, 75-80% of the added plant residue was decomposed, cumulative CO2 emission constituted 1,200 µm C g(-1) soil, and movement of C from decomposing plant residue into adjacent soil was insignificant. In the samples with greater abundance of water-filled small pores, 60% of the added plant residue was decomposed, cumulative CO2 emission constituted 2,000 µm C g(-1) soil, and the movement of residue C into adjacent soil was substantial. In the absence of plant residue the influence of pore characteristics on CO2 emission, that is on decomposition of the native soil organic C, was negligible. The microbial communities on the plant residue in the samples with large pores had more microbial groups known to be cellulose decomposers, that is, Bacteroidetes, Proteobacteria, Actinobacteria, and Firmicutes, while a number of oligotrophic Acidobacteria groups were more abundant on the plant residue from the samples with small pores. This study provides the first experimental evidence that characteristics of soil pores and their air/water flow status determine the phylogenetic composition of the local microbial community and directions and magnitudes of soil C

Direct gas-solid carbonation of serpentinite residues in the absence and presence of water vapor: a feasibility study for carbon dioxide sequestration.

Science.gov (United States)

Veetil, Sanoopkumar Puthiya; Pasquier, Louis-César; Blais, Jean-François; Cecchi, Emmanuelle; Kentish, Sandra; Mercier, Guy

2015-09-01

Mineral carbonation of serpentinite mining residue offers an environmentally secure and permanent storage of carbon dioxide. The strategy of using readily available mining residue for the direct treatment of flue gas could improve the energy demand and economics of CO2 sequestration by avoiding the mineral extraction and separate CO2 capture steps. The present is a laboratory scale study to assess the possibility of CO2 fixation in serpentinite mining residues via direct gas-solid reaction. The degree of carbonation is measured both in the absence and presence of water vapor in a batch reactor. The gas used is a simulated gas mixture reproducing an average cement flue gas CO2 composition of 18 vol.% CO2. The reaction parameters considered are temperature, total gas pressure, time, and concentration of water vapor. In the absence of water vapor, the gas-solid carbonation of serpentinite mining residues is negligible, but the residues removed CO2 from the feed gas possibly due to reversible adsorption. The presence of small amount of water vapor enhances the gas-solid carbonation, but the measured rates are too low for practical application. The maximum CO2 fixation obtained is 0.07 g CO2 when reacting 1 g of residue at 200 °C and 25 barg (pCO2 ≈ 4.7) in a gas mixture containing 18 vol.% CO2 and 10 vol.% water vapor in 1 h. The fixation is likely surface limited and restricted due to poor gas-solid interaction. It was identified that both the relative humidity and carbon dioxide-water vapor ratio have a role in CO2 fixation regardless of the percentage of water vapor.

Solid-Phase Extraction and Large-Volume Sample Stacking-Capillary Electrophoresis for Determination of Tetracycline Residues in Milk

Directory of Open Access Journals (Sweden)

Gabriela Islas

2018-01-01

Full Text Available Solid-phase extraction in combination with large-volume sample stacking-capillary electrophoresis (SPE-LVSS-CE was applied to measure chlortetracycline, doxycycline, oxytetracycline, and tetracycline in milk samples. Under optimal conditions, the proposed method had a linear range of 29 to 200 µg·L−1, with limits of detection ranging from 18.6 to 23.8 µg·L−1 with inter- and intraday repeatabilities < 10% (as a relative standard deviation in all cases. The enrichment factors obtained were from 50.33 to 70.85 for all the TCs compared with a conventional capillary zone electrophoresis (CZE. This method is adequate to analyze tetracyclines below the most restrictive established maximum residue limits. The proposed method was employed in the analysis of 15 milk samples from different brands. Two of the tested samples were positive for the presence of oxytetracycline with concentrations of 95 and 126 µg·L−1. SPE-LVSS-CE is a robust, easy, and efficient strategy for online preconcentration of tetracycline residues in complex matrices.

Residue determination and levels of glyphosate in surface waters, sediments and soils associated with oil palm plantation in Tasik Chini, Pahang, Malaysia

Science.gov (United States)

Mardiana-Jansar, K.; Ismail, B. S.

2014-09-01

Levels of glyphosate and its main metabolite were determined in surface water, soil and sediment samples from an oil palm plantation area located at Tasik Chini, Pahang, Malaysia. The optimization analytical method has been developed for the determination of glyphosate herbicide and its metabolite amino-methyl-phosphonic acid (AMPA) in surface waters to a level of 0.1μg/L, while in sediments and soils to a level of 0.5μg/g with a good linearity in the calibration range of 1-100μg/L. The procedure involves a pre-columnderivatization step with 9-fluorenyl-methyl-chloroformate (FMOC-Cl) yielding highly fluorescent derivatives of the analytes which can be determined by HPLC with fluorescence detection. In the field, levels of glyphosate in surface waters ranges from not detected to 1.0mg/L, while in soils and sediments were from not detected to 6.0mg/kg. For AMPA, the residues in surface waters were between not detected to 2.0mg/L, while in soil and sediment samples were from not detected to 5mg/kg. This variation of glyphosate and AMPA levels depended directly on time of pesticide application and the season.

Soil Gas Sample Handling: Evaluation of Water Removal and Sample Ganging

Energy Technology Data Exchange (ETDEWEB)

Fritz, Brad G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Abrecht, David G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hayes, James C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mendoza, Donaldo P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-10-31

Soil gas sampling is currently conducted in support of Nuclear Test Ban treaty verification. Soil gas samples are collected and analyzed for isotopes of interest. Some issues that can impact sampling and analysis of these samples are excess moisture and sample processing time. Here we discuss three potential improvements to the current sampling protocol; a desiccant for water removal, use of molecular sieve to remove CO₂ from the sample during collection, and a ganging manifold to allow composite analysis of multiple samples.

Ground-water sample collection and analysis plan for the ground-water surveillance project

International Nuclear Information System (INIS)

Bryce, R.W.; Evans, J.C.; Olsen, K.B.

1991-12-01

The Pacific Northwest Laboratory performs ground-water sampling activities at the US Department of Energy's (DOE's) Hanford Site in support of DOE's environmental surveillance responsibilities. The purpose of this document is to translate DOE's General Environmental Protection Program (DOE Order 5400.1) into a comprehensive ground-water sample collection and analysis plan for the Hanford Site. This sample collection and analysis plan sets forth the environmental surveillance objectives applicable to ground water, identifies the strategy for selecting sample collection locations, and lists the analyses to be performed to meet those objectives

In-situ observation of dislocation and analysis of residual stresses by FEM/DDM modeling in water cavitation peening of pure titanium

International Nuclear Information System (INIS)

Ju, D Y; Han, B

2015-01-01

In this paper, in order to approach this problem, specimens of pure titanium were treated with WCP, and the subsequent changes in microstructure, residual stress, and surface morphologies were investigated as a function of WCP duration. The influence of water cavitation peening (WCP) treatment on the microstructure of pure titanium was investigated. A novel combined finite element and dislocation density method (FEM/DDM), proposed for predicting macro and micro residual stresses induced on the material subsurface treated with water cavitation peening, is also presented. A bilinear elastic-plastic finite element method was conducted to predict macro-residual stresses and a dislocation density method was conducted to predict micro-residual stresses. These approaches made possible the prediction of the magnitude and depth of residual stress fields in pure titanium. The effect of applied impact pressures on the residual stresses was also presented. The results of the FEM/DDM modeling were in good agreement with those of the experimental measurements. (paper)

Isolation of a bacteria of the Bacillus genus as indicator in the disinfection of residual waters by means of the ionizing radiation (e{sup -} , {gamma}); Aislamiento de una bacteria del genero Bacillus como indicador en la desinfeccion de aguas residuales mediante la radiacion ionizante (e{sup -} , {gamma})

Energy Technology Data Exchange (ETDEWEB)

Mata J, M

2003-07-01

The pollutants of the water can be chemical, physical and biological. Among those biological we find to the microorganisms: bacterias, virus and protozoa. These cause important infections in many countries, mainly of Latin America. With the advance of the technology and the quick demographic growth, the biological pollution of the water has already become an important topic since it would damage the public health and it causes that their disinfection has greater attention. In the treatment of residual waters three basic treatments exist the one primary, secondary and tertiary; in this last we find the disinfection, which can be taken to end by chemical and physical methods. For this work of investigation it was used the ionizing radiation, because it is an innovative technology that it eliminates microorganisms in residual waters. The investigation consisted on treating, samples of residual water after the biological treatment of the plant RECICLAGUA with ionizing radiation (electrons and gammas), for the case of electrons it was used the dose of 0.5 kGy and for gamma the dose, of 5 kGy, later the survivor bacteria was isolated to these doses in both cases and they were carried out the tests of identification. In accordance with the obtained results can say that it is about a B. subtilis. The isolated B.subtilis was presented as a pollutant of the flora of the residual water, having a greater survival to the dose of 0.5 and 5 kGy with electrons and gammas, respectively that other present polluting microorganisms in the samples of residual water. For it fits signalize that this microorganism shows characteristics as it easy isolation and identification, the presence with pathogen microorganisms and a greater survival when being irradiated, therefore it can use as indicator in the disinfection of residual waters through ionizing radiation (electrons and gammas). (Author)

Sublimation and transport of water from the north residual polar cap on Mars

Science.gov (United States)

Haberle, Robert M.; Jakosky, Bruce M.

1990-01-01

The possible role of the north residual cap in the current Martian water cycle was examined using models to assess the ability of the cap to supply water to the atmosphere and the ability of the atmospheric circulation to transport it out of the polar regions to low northern latitudes. Results indicate that rather extreme circumstances would be required for the cap to provide all of the observed increase in atmospheric water, such as a combination of high surface winds, low cap emissivities, or substantial evaporation from dark material. But even if these conditions could be met, the high-latitude circulation is too localized in scale to move much water vapor out of the polar environment. Both the present calculations and the data from the Viking's Mars Atmospheric Water Detection Experiment show that about two thirds of the water appearing in the Martian northern hemisphere during summer must be supplied by other sources. It is suggested that the additional source is water desorbing from the nonpolar regolith.

A procedure for evaluating residual life of major components in light water reactors

International Nuclear Information System (INIS)

Uchida, S.; Fujimori, H.; Ibe, E.; Kuniya, J.; Hayashi, M.; Fuse, M.; Yamauchi, K.

1995-01-01

A computer program for evaluating residual life of major components in boiling water reactors is proposed. It divides the stress corrosion cracking process into two stages; a probabilistic crack generation stage and a deterministic crack propagation one. The minimum period of the crack generation stage is evaluated assuming an exponential distribution of the stage. The crack propagation rate is calculated by the slip-dissolution/film-rupture model. The neutron flux and fluence dependence of the neutron radiation effects on material properties was evaluated by using theoretical models of radiation damage. The computer program works on an engineering work station. Evaluated results are displayed as a map of the residual life, or as graphs of crack length evolution

PCR detection of Burkholderia multivorans in water and soil samples.

Science.gov (United States)

Peeters, Charlotte; Daenekindt, Stijn; Vandamme, Peter

2016-08-12

Although semi-selective growth media have been developed for the isolation of Burkholderia cepacia complex bacteria from the environment, thus far Burkholderia multivorans has rarely been isolated from such samples. Because environmental B. multivorans isolates mainly originate from water samples, we hypothesized that water rather than soil is its most likely environmental niche. The aim of the present study was to assess the occurrence of B. multivorans in water samples from Flanders (Belgium) using a fast, culture-independent PCR assay. A nested PCR approach was used to achieve high sensitivity, and specificity was confirmed by sequencing the resulting amplicons. B. multivorans was detected in 11 % of the water samples (n = 112) and 92 % of the soil samples (n = 25) tested. The percentage of false positives was higher for water samples compared to soil samples, showing that the presently available B. multivorans recA primers lack specificity when applied to the analysis of water samples. The results of the present study demonstrate that B. multivorans DNA is commonly present in soil samples and to a lesser extent in water samples in Flanders (Belgium).

Review of sample preparation techniques for the analysis of pesticide residues in soil.

Science.gov (United States)

Tadeo, José L; Pérez, Rosa Ana; Albero, Beatriz; García-Valcárcel, Ana I; Sánchez-Brunete, Consuelo

2012-01-01

This paper reviews the sample preparation techniques used for the analysis of pesticides in soil. The present status and recent advances made during the last 5 years in these methods are discussed. The analysis of pesticide residues in soil requires the extraction of analytes from this matrix, followed by a cleanup procedure, when necessary, prior to their instrumental determination. The optimization of sample preparation is a very important part of the method development that can reduce the analysis time, the amount of solvent, and the size of samples. This review considers all aspects of sample preparation, including extraction and cleanup. Classical extraction techniques, such as shaking, Soxhlet, and ultrasonic-assisted extraction, and modern techniques like pressurized liquid extraction, microwave-assisted extraction, solid-phase microextraction and QuEChERS (Quick, Easy, Cheap, Effective, Rugged, and Safe) are reviewed. The different cleanup strategies applied for the purification of soil extracts are also discussed. In addition, the application of these techniques to environmental studies is considered.

Sampling procedure, receipt and conservation of water samples to determine environmental radioactivity

International Nuclear Information System (INIS)

Herranz, M.; Navarro, E.; Payeras, J.

2009-01-01

The present document informs about essential goals, processes and contents that the subgroups Sampling and Samples Preparation and Conservation believe they should be part of the procedure to obtain a correct sampling, receipt, conservation and preparation of samples of continental, marine and waste water before qualifying its radioactive content.

Using of abrasive water jet for measurement of residual stress in railway wheels

Czech Academy of Sciences Publication Activity Database

Hlaváček, Petr; Brumek, J.; Horsák, L.

2012-01-01

Roč. 2, č. 19 (2012), s. 387-390 ISSN 1330-3651 R&D Projects: GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : abrasive water jet * railway wheel * residual stress Subject RIV: JQ - Machines ; Tools Impact factor: 0.601, year: 2012 http://hrcak.srce.hr/index.php?show=clanak&id_clanak_jezik=124848

Green and efficient sample preparation method for the determination of catalyst residues in margarine by ICP-MS.

Science.gov (United States)

Hartwig, Carla Andrade; Pereira, Rodrigo Mendes; Novo, Diogo La Rosa; Oliveira, Dirce Taina Teixeira; Mesko, Marcia Foster

2017-11-01

Responding to the need for green and efficient methods to determine catalyst residues with suitable precision and accuracy in samples with high fat content, the present work evaluates a microwave-assisted ultraviolet digestion (MW-UV) system for margarines and subsequent determination of Ni, Pd and Pt using inductively coupled plasma mass spectrometry (ICP-MS). It was possible to digest up to 500mg of margarine using only 10mL of 4molL -1 HNO 3 with a digestion efficiency higher than 98%. This allowed the determination of catalyst residues using the ICP-MS and free of interferences. For this purpose, the following experimental parameters were evaluated: concentration of digestion solution, sample mass and microwave irradiation program. The residual carbon content was used as a parameter to evaluate the efficiency of digestion and to select the most suitable experimental conditions. The accuracy evaluation was performed by recovery tests using a standard solution and certified reference material, and recoveries ranging from 94% to 99% were obtained for all analytes. The limits of detection for Ni, Pd and Pt using the proposed method were 35.6, 0.264 and 0.302ngg -1 , respectively. When compared to microwave-assisted digestion (MW-AD) in closed vessels using concentrated HNO 3 (used as a reference method for sample digestion), the proposed MW-UV could be considered an excellent alternative for the digestion of margarine, as this method requires only a diluted nitric acid solution for efficient digestion. In addition, MW-UV provides appropriate solutions for further ICP-MS determination with suitable precision (relative standard deviation < 7%) and accuracy for all evaluated analytes. The proposed method was applied to margarines from different brands produced in Brazil, and the concentration of catalyst residues was in agreement with the current legislation or recommendations. Copyright © 2017 Elsevier B.V. All rights reserved.

Experimental study on effect of roasting, boiling and microwave cooking methods on enrofloxacin antibiotic residues in edible poultry tissues

Directory of Open Access Journals (Sweden)

A Javadi

2011-11-01

Full Text Available The purpose of this study was to determine the effects of different cooking processes such as boiling, roasting and microwaving on enrofloxacin residues in muscle, liver and gizzard tissues of broiler chickens. Each of chicks was fed by routine diet and water with %0.05 of enrofloxacine for consecutive 5 days .Then; three locations including breast muscle, liver and gizzard were sampled aseptically from each carcass. Enrofloxacin residue was analyzed using microbial method by plates seeded with Escherichia coli. After doing different phases of the test on raw samples, the positive raw samples cooked by various cooking procedures and we surveyed cooked samples with similar method again for present of residue. The results were show reduction in concentration of enrofloxacin residue after different cooking processes. The most reduction of the residue in cooked meat and gizzard samples related to boiling process and roasting process for cooked liver samples and the highest detectable amount of residue belonged to microwaving process in all cooked samples. Regarding to the results of this study, we can conclude that cooking processes can’t annihilate total amounts of these drug and it can only decrease their amounts and the most of residue in boiling process excreted from tissue to cooking fluid.

Volume of baseline data on radioactivity in drinking water, ground water, waste water, sewage sludge, residues and wastes of the annual report 1988 'Environmental radioactivity and radiation exposure'

International Nuclear Information System (INIS)

Abelmann, S.; Buenger, T.; Fusban, H.U.; Ruehle, H.; Viertel, H.; Gans, I.

1991-01-01

This WaBoLu volume is a shortened version of the annual report by the Federal Ministry of the Environment, Nature Protection and Reactor Safety 'Environmental radioactivity and radiation exposure' and gives an overview of the data on radioactivity in drinking water, ground water, waste water, sewage sludge, residues and wastes, compiled for the area of the Federal Republic of Germany in 1988 by the Institute of Water, Soil and Air Hygiene (WaBoLu) of the Federal Health Office. (BBR) With 22 figs., 15 tabs [de

Alternative to Water Based Fabric Cleaner in Textile and Detergent Processes

Directory of Open Access Journals (Sweden)

Arpan Jain

2017-01-01

Full Text Available Three different detergent formulations, (1 ethyl-hydro-oxides (EHOs, using ethanol + H2O2 + KOH + water, without pH adjustment, at 60°C for 1 h, (2 modified EHOs (using ethanol + H2O2 + KOH + water, with pH adjustment, at 40°C for 1 h, and (3 water based detergent (WBD, using commercial detergent T + water, at 40°C for 1 h, were analyzed for cleaning of dried biodiesel soaked cotton cloth (DBSCC samples. The effects of detergent formulations were analyzed based on cloth sample weights (residual and intact and visual (through photographic images examinations. With EHOs formulations, the increasing concentration of KOH and H2O2 had a significant effect on increasing both brightness and residual content of DBSCC samples. On the contrary, the controlled pH environments (as with modified EHOs formulations had a significant effect in decreasing residual content and increasing brightness of DBSCC samples. The implications of EHOs formulations (with and without modification are discussed with respect to current water based textile and detergent industries practices.

Pesticide residues in individual versus composite samples of apples after fine or coarse spray quality application

NARCIS (Netherlands)

Poulsen, M.; Wenneker, M.; Withagen, J.C.M.; Christensen, H.B.

2012-01-01

In this study, field trials on fine and coarse spray quality application of pesticides on apples were performed. The main objectives were to study the variation of pesticide residue levels in individual fruits versus composite samples, and the effect of standard fine spray quality application versus

Position of residues in transmembrane peptides with respect to the lipid bilayer: A combined lipid NOEs and water chemical exchange approach in phospholipid bicelles

International Nuclear Information System (INIS)

Glover, Kerney Jebrell; Whiles, Jennifer A.; Vold, Regitze R.; Melacini, Giuseppe

2002-01-01

The model transmembrane peptide P16 was incorporated into small unaligned phospholipid bicelles, which provide a 'native-like' lipid bilayer compatible with high-resolution solution NMR techniques. Using amide-water chemical exchange and amide-lipid cross-relaxation measurements, the interactions between P16 and bicelles were investigated. Distinctive intermolecular NOE patterns observed in band-selective 2D-NOESY spectra of bicellar solutions with several lipid deuteration schemes indicated that P16 is preferentially interacting with the 'bilayered' region of the bicelle rather than with the rim. Furthermore, when amide-lipid NOEs were combined with amide-water chemical exchange cross-peaks of selectively 15 N-labeled P16 peptides, valuable information was obtained about the position of selected residues relative to the membrane-water interface. Specifically, three main classes were identified. Class I residues lie outside the bilayer and show amide-water exchange cross-peaks but no amide-lipid NOEs. Class II residues reside in the bilayer-water interface and show both amide-water exchange cross-peaks and amide-lipid NOEs. Class III residues are embedded within the hydrophobic core of the membrane and show no amide-water exchange cross-peaks but strong amide-lipid NOEs

Nutrient removal capacity of wood residues for the Agro-environmental safety of ground and surface waters

Directory of Open Access Journals (Sweden)

Paulo A. Dumont

2014-07-01

Full Text Available The aim of this study was to determine the effectiveness of wood residues in the removal of nutrients (ammonium-N; NH4-N from nutrient-rich (NH4-N waters. The water holding capacity of the wood materials was also determined. Carried out at Rothamsted Research, North Wyke, UK, this controlled laboratory experiment tested two wood residues; in length, one being 1-2cm and the other from 150 µm (microns to 9.5mm. Although a wide range of studies have shown the effectiveness and performance of various absorbent materials as animal beddings, such as straw (cereal straw, woodchip (sawdust, bark or wood shavings, bracken and rushes, only few have focused on the NH4-N sorption/desorption capacity. The depuration capacity of wood residues from nutrient-rich effluents such as those from cattle bedded on woodchip or straw will be controlled by processes such as sorption (adsorption-absorption and desorption of nutrients. Studies have reported the nitrogen removal capacity of woodchip materials and biochar from woodchip as well as removal of NH4+-N from domestic and municipal wastewater, farm dirty water, landfill and industry effluents. These studies have observed that the mechanism of removal of nitrogen is by either increasing NO3--N removal form leachate by enhancing N2O losses via denitrification (biochar as carbon source for denitrifiers or by decreasing NH4+-N in leachate through adsorption to negatively charged sites. Results showed that although the cation exchange capacity (CEC and surface area (SA are both fundamental properties of adsorbent materials, no correlation was found with CEC and adsorption or desorption. Nor did changes in pH appear to be sufficiently important to cause changes in CEC. For this reason, osmotic pressure appeared to be a more predominant parameter controlling processes of adsorption and desorption of NH4+-N in both wood residues. Thus, wood residues high in NH4+-N should be avoided, as they could have an opposite effect

UMTRA water sampling and analysis plan, Green River, Utah

International Nuclear Information System (INIS)

Papusch, R.

1993-12-01

The purpose of this water sampling and analysis plan (WSAP) is to provide a basis for groundwater and surface water sampling at the Green River Uranium Mill Tailing Remedial Action (UMTRA) Project site. This WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring locations

Pesticide residues in locally available cereals and vegetables

International Nuclear Information System (INIS)

Cunanan, S.A.; Santos, F.L.; Bonoan, L.S.

1976-03-01

Vegetable samples (pechay, cabbage, lettuce, green beans and tomatoes) bought from public markets in the Metro Manila area were analyzed for pesticide residues using gas chromatography. The samples analyzed in 1968-69 contained high levels of chlorinated pesticides such as DDT, Aldrin, Endrin, and Thiodan, while in the samples analyzed in January 1976, no chlorinated and organophosphate pesticides were detected. Cereal samples (rice, corn and sorghum) were obtained from the National Grains Authority and analyzed for pesticide residues and bromine residues. Total bromine residues was determined by neutron activation analysis. In most of the samples analyzed, the concentrations of pesticide residues were below the tolerance levels set by the FAO/WHO Committee on Pesticide Residues in Foods. An exception was one rice sample from Thailand, the bromine residue content (110ppm) of which exceeds the tolerance level of 50ppm

Physico-chemical characteristics of water sample from Aiba Stream ...

African Journals Online (AJOL)

This study aimed at assessing the effectiveness of solar distillation in purification of water. The water sample collected from Aiba stream was subjected to double slope solar water distillation unit. The physico- chemical characteristics of the raw sample and the distillate were determined using standard methods. The.

Extraction of toxic and valuable metals from wastewater sludge and ash arising from RECICLAGUA, a treatment plant for residual waters applying the leaching technique

International Nuclear Information System (INIS)

Guerrero D, J.J.

2004-01-01

Presently work, the technique is applied of having leached using coupled thermostatted columns, the X-ray diffraction for the identification of the atomic and molecular structure of the metals toxic that are present in the residual muds of a treatment plant of water located in the municipality of the Estado de Mexico, RECICLAGUA, likewise the techniques is used of Inductively Coupled Plasma Mass Spectroscopy and X-ray fluorescence analysis for the qualitative analysis. We took samples of residual sludge and incinerated ash of a treatment plant waste water from the industrial corridor Toluca-Lerma RECICLAGUA, located in Lerma, Estado de Mexico. For this study 100 g. of residual of sludge mixed with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one p H at 2, 5, 7 and 10, bisulfite was added, of 0.3-1.5 g of dodecyl sulfate of sodium and 3.93 g of DTPA (triple V). Diethylene triamine penta acetate. These sludges and ashes were extracted from toxic and valuable metals by means of the leaching technique using coupled thermostated columns that which were designed by Dr. Jaime Vite Torres, it is necessary to make mention that so much the process as the apparatus with those that one worked was patented by him same. With the extraction of these metals, benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much use of those residuals, once the metals have been eliminated, as of those residuals, once the metals have been eliminated, as of those liquors, the heavy metals were extracted. It was carried out a quantitative analysis using Icp mass spectroscopy, this way to be able to know the one content of the present metals in the samples before and after of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the analysis by X-ray diffraction that provides an elementary content of the

Measurement of 90Sr in fresh water samples

International Nuclear Information System (INIS)

Belanova, A.; Meresova, J.; Svetlik, I.; Tomaskova, L.

2008-01-01

This preliminary study show new experimental approach to the determination of the radionuclide 90 Sr in water samples. The new method of dynamic windows utilizing liquid scintillation counting was applied on model and surface water samples. Our results show the demand of separation technique with significantly higher yields. (authors)

Development of a New Microextraction Fiber Combined to On-Line Sample Stacking Capillary Electrophoresis UV Detection for Acidic Drugs Determination in Real Water Samples

Science.gov (United States)

Araujo, Lilia; Prieto, Avismelsi; Navalón, Alberto; Vílchez, José Luis; Valera, Paola; Zambrano, Ana; Dugas, Vincent

2017-01-01

A new analytical method coupling a (off-line) solid-phase microextraction with an on-line capillary electrophoresis (CE) sample enrichment technique was developed for the analysis of ketoprofen, naproxen and clofibric acid from water samples, which are known as contaminants of emerging concern in aquatic environments. New solid-phase microextraction fibers based on physical coupling of chromatographic supports onto epoxy glue coated needle were studied for the off-line preconcentration of these micropollutants. Identification and quantification of such acidic drugs were done by capillary zone electrophoresis (CZE) using ultraviolet diode array detection (DAD). Further enhancement of concentration sensitivity detection was achieved by on-line CE “acetonitrile stacking” preconcentration technique. Among the eight chromatographic supports investigated, Porapak Q sorbent showed higher extraction and preconcentration capacities. The screening of parameters that influence the microextraction process was carried out using a two-level fractional factorial. Optimization of the most relevant parameters was then done through a surface response three-factor Box-Behnken design. The limits of detection and limits of quantification for the three drugs ranged between 0.96 and 1.27 µg∙L−1 and 2.91 and 3.86 µg∙L−1, respectively. Recovery yields of approximately 95 to 104% were measured. The developed method is simple, precise, accurate, and allows quantification of residues of these micropollutants in Genil River water samples using inexpensive fibers. PMID:28686186

Development of a New Microextraction Fiber Combined to On-Line Sample Stacking Capillary Electrophoresis UV Detection for Acidic Drugs Determination in Real Water Samples

Directory of Open Access Journals (Sweden)

Maria Espina-Benitez

2017-07-01

Full Text Available A new analytical method coupling a (off-line solid-phase microextraction with an on-line capillary electrophoresis (CE sample enrichment technique was developed for the analysis of ketoprofen, naproxen and clofibric acid from water samples, which are known as contaminants of emerging concern in aquatic environments. New solid-phase microextraction fibers based on physical coupling of chromatographic supports onto epoxy glue coated needle were studied for the off-line preconcentration of these micropollutants. Identification and quantification of such acidic drugs were done by capillary zone electrophoresis (CZE using ultraviolet diode array detection (DAD. Further enhancement of concentration sensitivity detection was achieved by on-line CE “acetonitrile stacking” preconcentration technique. Among the eight chromatographic supports investigated, Porapak Q sorbent showed higher extraction and preconcentration capacities. The screening of parameters that influence the microextraction process was carried out using a two-level fractional factorial. Optimization of the most relevant parameters was then done through a surface response three-factor Box-Behnken design. The limits of detection and limits of quantification for the three drugs ranged between 0.96 and 1.27 µg∙L−1 and 2.91 and 3.86 µg∙L−1, respectively. Recovery yields of approximately 95 to 104% were measured. The developed method is simple, precise, accurate, and allows quantification of residues of these micropollutants in Genil River water samples using inexpensive fibers.

Development of a New Microextraction Fiber Combined to On-Line Sample Stacking Capillary Electrophoresis UV Detection for Acidic Drugs Determination in Real Water Samples.

Science.gov (United States)

Espina-Benitez, Maria; Araujo, Lilia; Prieto, Avismelsi; Navalón, Alberto; Vílchez, José Luis; Valera, Paola; Zambrano, Ana; Dugas, Vincent

2017-07-07

A new analytical method coupling a (off-line) solid-phase microextraction with an on-line capillary electrophoresis (CE) sample enrichment technique was developed for the analysis of ketoprofen, naproxen and clofibric acid from water samples, which are known as contaminants of emerging concern in aquatic environments. New solid-phase microextraction fibers based on physical coupling of chromatographic supports onto epoxy glue coated needle were studied for the off-line preconcentration of these micropollutants. Identification and quantification of such acidic drugs were done by capillary zone electrophoresis (CZE) using ultraviolet diode array detection (DAD). Further enhancement of concentration sensitivity detection was achieved by on-line CE "acetonitrile stacking" preconcentration technique. Among the eight chromatographic supports investigated, Porapak Q sorbent showed higher extraction and preconcentration capacities. The screening of parameters that influence the microextraction process was carried out using a two-level fractional factorial. Optimization of the most relevant parameters was then done through a surface response three-factor Box-Behnken design. The limits of detection and limits of quantification for the three drugs ranged between 0.96 and 1.27 µg∙L -1 and 2.91 and 3.86 µg∙L -1 , respectively. Recovery yields of approximately 95 to 104% were measured. The developed method is simple, precise, accurate, and allows quantification of residues of these micropollutants in Genil River water samples using inexpensive fibers.

Synthesis, characterization and fluorescent properties of water-soluble glycopolymer bearing curcumin pendant residues.

Science.gov (United States)

Zhang, Haisong; Yu, Meng; Zhang, Hailei; Bai, Libin; Wu, Yonggang; Wang, Sujuan; Ba, Xinwu

2016-08-01

Curcumin is a potential natural anticancer drug with low oral bioavailability because of poor water solubility. The aqueous solubility of curcumin is enhanced by means of modification with the carbohydrate units. Polymerization of the curcumin-containing monomer with carbohydrate-containing monomer gives the water-soluble glycopolymer bearing curcumin pendant residues. The obtained copolymers (P1 and P2) having desirable water solubility were well-characterized by infrared spectroscopy (IR), nuclear magnetic resonance (NMR), gel permeation chromatography (GPC), UV-Vis absorption spectroscopy, and photoluminescence spectroscopy. The copolymer P2 with a molar ratio of 1:6 (curcumin/carbohydrate) calculated from the proton NMR results exhibits a similar anticancer activity compared to original curcumin, which may serve as a potential chemotherapeutic agent in the field of anticancer medicine.

Validated electrochemical and chromatographic quantifications of some antibiotic residues in pharmaceutical industrial waste water.

Science.gov (United States)

Ibrahim, Heba K; Abdel-Moety, Mona M; Abdel-Gawad, Sherif A; Al-Ghobashy, Medhat A; Kawy, Mohamed Abdel

2017-03-01

Realistic implementation of ion selective electrodes (ISEs) into environmental monitoring programs has always been a challenging task. This could be largely attributed to difficulties in validation of ISE assay results. In this study, the electrochemical response of amoxicillin trihydrate (AMX), ciprofloxacin hydrochloride (CPLX), trimethoprim (TMP), and norfloxacin (NFLX) was studied by the fabrication of sensitive membrane electrodes belonging to two types of ISEs, which are polyvinyl chloride (PVC) membrane electrodes and glassy carbon (GC) electrodes. Linear response for the membrane electrodes was in the concentration range of 10 -5 -10 -2  mol/L. For the PVC membrane electrodes, Nernstian slopes of 55.1, 56.5, 56.5, and 54.0 mV/decade were achieved over a pH 4-8 for AMX, CPLX, and NFLX, respectively, and pH 3-6 for TMP. On the other hand, for GC electrodes, Nernstian slopes of 59.1, 58.2, 57.0, and 58.2 mV/decade were achieved over pH 4-8 for AMX, CPLX, and NFLX, respectively, and pH 3-6 for TMP. In addition to assay validation to international industry standards, the fabricated electrodes were also cross-validated relative to conventional separation techniques; high performance liquid chromatography (HPLC), and thin layer chromatography (TLC)-densitometry. The HPLC assay was applied in concentration range of 0.5-10.0 μg/mL, for all target analytes. The TLC-densitometry was adopted over a concentration range of 0.3-1.0 μg/band, for AMX, and 0.1-0.9 μg/band, for CPLX, NFLX, and TMP. The proposed techniques were successfully applied for quantification of the selected drugs either in pure form or waste water samples obtained from pharmaceutical plants. The actual waste water samples were subjected to solid phase extraction (SPE) for pretreatment prior to the application of chromatographic techniques (HPLC and TLC-densitometry). On the other hand, the fabricated electrodes were successfully applied for quantification of the antibiotic residues in actual

Determination of Profenofos Pesticidal Residue in Lettuce (Lactuca sativa L. by Gas Chromatographic Method

Directory of Open Access Journals (Sweden)

Yohannes Alen

2015-05-01

Full Text Available The determination of profenofos pesticidal residue in the lettuce (Lactuca sativa L. by using gas chromatography using flame photometric detector (FPD had been investigated. The lettuce was collected from Padang Luar area, Agam distric, West Sumatera. Sample for determination of profenofos residue divided into three groups: unwashed (A, washed with water (B, and washed with detergent (C. Maceration with sonication was used for the extraction using ethylacetateas a solvent. The results showed that profenofos pesticide residue in sample A, B and C were 0.204, 0.080 and 0.061 ppm, respectively. These profenofos pesticidal residue are over than the Maximum Residue Limits (MRL that established by The Japan Food Chemical Research Foundation (0.05 ppm even though World Health Organization (WHO has not established Maximum Residue Limits (MRL profenofos on lettuce. Based on the statistical analysis one-way method (Anova using SPSS 20.0 showed that there was a significant concentrations difference between lettuce A from lettuce B and lettuce C with p < 0.05.

Accumulation of pesticide residues by shrimp, fish and brine shrimp during pond culture at Ghorabari (District Thatta)

International Nuclear Information System (INIS)

Sultana, R.; Wajeeha, F.A.; Ameer, F.; Munshi, A.B.; Nasir, M.

2012-01-01

Residual level of persistent organo chlorines (OC) such as sigma-HCH (alpha-HCH, beta-HCH, gamma-HCH, delta-HCH, sigma-DDT (o,p'-DDD, op-DDE, p,p-DDE pp-DDD, pp'-DDT, o,p'-DDT), dieldrin and endrin were measured in a number of water samples from Ambro creek and their accumulation in shrimp (Penaeus merguiensis and P. penicillatus), fish (Otolithes ruber) and brine shrimp (Artemia sp.) reared in ponds for a period of four months. Samples were extracted with organic solvents, and quantified using gas chromatography-electron capture detection (GC/ECD). It has been found that results of animal tissue and water are not same however OCs, (mainly sigma DT and beta-HCH 4,4-DDT, Dieldrin + 2,4-DDT, and Methoxychlor were detected in all samples ). Heptachlor exo-epoxide were found in fish and Artemia sp. and absent in all shrimp samples. Heptachlor endo-epoxide was detected only in Artemia sp. and average residual concentration of OCs in Artemia sp. was 0.004-0.09 ppm. Methoxychlor was found in the highest quantity in all the samples whether it was fish, shrimp or Artemia. In fish average residual concentration of all (OCs) in individual sample was 0.03 - 0.180 ppm. (author)

Removal of uranyl ions from residual waters using some algae types

International Nuclear Information System (INIS)

Cecal, Al.; Rudic, V.; Gulea, A.; Palamaru, I.; Humelnicu, D.; Salaru, V.V.; Popa, K.

1997-01-01

This paper deals with a study on the bioaccumulation of uranyl ions resulted from residual effluents, by means of some microbiological collectors: Scenedesmus quadricauda, Anabaena karakumica, Calothrix brevissima, Penicillium sp, as well as the Glucide extract of Porphyridium cruentum, in several experimental conditions. The retaining degree of the bioaccumulated uranyl ions, as well as the leaching degree, in HCl and H 2 O media, of the same ions previously retained on algae, were karakumica >Penicillium sp> Calothrix brevissima. The leaching effect of bioaccumulated uranyl ions is higher in hydrochloric acid then in water. (authors)

Investigation of hydrophobic substrates for solution residue analysis utilizing an ambient desorption liquid sampling-atmospheric pressure glow discharge microplasma.

Science.gov (United States)

Paing, Htoo W; Marcus, R Kenneth

2018-03-12

A practical method for preparation of solution residue samples for analysis utilizing the ambient desorption liquid sampling-atmospheric pressure glow discharge optical emission spectroscopy (AD-LS-APGD-OES) microplasma is described. Initial efforts involving placement of solution aliquots in wells drilled into copper substrates, proved unsuccessful. A design-of-experiment (DOE) approach was carried out to determine influential factors during sample deposition including solution volume, solute concentration, number of droplets deposited, and the solution matrix. These various aspects are manifested in the mass of analyte deposited as well as the size/shape of the product residue. Statistical analysis demonstrated that only those initial attributes were significant factors towards the emission response of the analyte. Various approaches were investigated to better control the location/uniformity of the deposited sample. Three alternative substrates, a glass slide, a poly(tetrafluoro)ethylene (PTFE) sheet, and a polydimethylsiloxane (PDMS)-coated glass slide, were evaluated towards the microplasma analytical performance. Co-deposition with simple organic dyes provided an accurate means of determining the location of the analyte with only minor influence on emission responses. The PDMS-coated glass provided the best performance by virtue of its providing a uniform spatial distribution of the residue material. This uniformity yielded an improved limits of detection by approximately 22× for 20 μL and 4 x for 2 μL over the other two substrates. While they operate by fundamentally different processes, this choice of substrate is not restricted to the LS-APGD, but may also be applicable to other AD methods such as DESI, DART, or LIBS. Further developments will be directed towards a field-deployable ambient desorption OES source for quantitative analysis of microvolume solution residues of nuclear forensics importance.

UMTRA project water sampling and analysis plan -- Shiprock, New Mexico

International Nuclear Information System (INIS)

1994-02-01

Water sampling and analysis plan (WSAP) is required for each U.S. Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site to provide a basis for ground water and surface water sampling at disposal and former processing sites. This WSAP identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the monitoring stations at the Navaho Reservation in Shiprock, New Mexico, UMTRA Project site. The purposes of the water sampling at Shiprock for fiscal year (FY) 1994 are to (1) collect water quality data at new monitoring locations in order to build a defensible statistical data base, (2) monitor plume movement on the terrace and floodplain, and (3) monitor the impact of alluvial ground water discharge into the San Juan River. The third activity is important because the community of Shiprock withdraws water from the San Juan River directly across from the contaminated alluvial floodplain below the abandoned uranium mill tailings processing site

Aluminum-Based Water Treatment Residue Reuse for Phosphorus Removal

Directory of Open Access Journals (Sweden)

Lai Yoke Lee

2015-04-01

Full Text Available Aluminum-based water treatment residue (Al-WTR generated during the drinking water treatment process is a readily available recycled material with high phosphorus (P adsorption capacity. The P adsorption capacity of Al-WTR generated from Singapore’s water treatment plant was evaluated with reference to particle size range, adsorption pH and temperature. Column tests, with WTR amendments in sand with and without compost, were used to simulate the bioretention systems. The adsorption rate decreased with increasing WTR sizes. Highest P adsorption capacity, 15.57 mg PO43−-P/g WTR, was achieved using fine WTR particles (>50% particles at less than 0.30 mm. At pH 4, the contact time required to reduce effluent P concentration to below the detectable range was half compared with pH 7 and 9. The adsorption rate observed at 40 ± 2 °C was 21% higher compared with that at 30 ± 2 °C. Soil mixes amended with 10% WTR and compost were able to maintain consistently high (90% total phosphorus (TP removal efficiency at a TP load up to 6.45 g/m3. In contrast, TP removal efficiencies associated with columns without WTR amendment decreased to less than 45% as the TP load increased beyond 4.5 g/m3. The results showed that WTR application is beneficial for enhanced TP removal in bioretention systems.

Analysis of phthalate esters contamination in drinking water samples ...

African Journals Online (AJOL)

The optimum condition method was successfully applied to the analysis of phthalate esters contamination in bottled drinking water samples. The concentration of DMP, DEP and DBP in drinking water samples were below allowable levels, while the DEHP concentration in three samples was found to be greater than the ...

The Soil-Water Characteristic Curve of Unsaturated Tropical Residual Soil

Science.gov (United States)

Yusof, M. F.; Setapa, A. S.; Tajudin, S. A. A.; Madun, A.; Abidin, M. H. Z.; Marto, A.

2016-07-01

This study was conducted to determine the SWCC of unsaturated tropical residual soil in Kuala Lumpur, Malaysia. Undisturbed soil samples at five locations of high-risk slopes area were taken at a depth of 0.5 m using block sampler. In the determination of the SWCC, the pressure plate extractor with the capacity of 1500 kN/m2 has been used. The index properties of the soil such as natural moisture content, Atterberg limits, specific gravity, and soil classification are performed according to BS 1377: Part 2: 1990. The results of index properties show that the natural moisture content of the soil is between 36% to 46%, the plasticity index is between 10% - 26%, the specific gravity is between 2.51 - 2.61 and the soils is classified as silty organic clay of low plasticity. The SWCC data from the pressure plate extractor have been fitted with the Fredlund and Xing equation. The results show that the air entry value and residual matric suction for residual soils are in the range of 17 kN/m2 to 24 kN/m2 and 145 kN/m2 to 225 kN/m2 respectively. From the fitting curve, it is found that the average value of the Fredlund and Xing parameters such as a, n and m are in the range of 0.24-0.299, 1.7-4.8 and 0.142-0.440 respectively.

Determination of Phthalates in Drinking Water Samples

African Journals Online (AJOL)

user

successfully applied to the analysis of phthalate esters contamination in bottled drinking water samples. ... esters are used in the manufacturing of polyvinyl chloride. (PVC). ... water, soil, air, food products and the human body. (Castillo et al.

A supersensitive silver nanoprobe based aptasensor for low cost detection of malathion residues in water and food samples

Science.gov (United States)

Bala, Rajni; Mittal, Sherry; Sharma, Rohit K.; Wangoo, Nishima

2018-05-01

In the present study, we report a highly sensitive, rapid and low cost colorimetric monitoring of malathion (an organophosphate insecticide) employing a basic hexapeptide, malathion specific aptamer (oligonucleotide) and silver nanoparticles (AgNPs) as a nanoprobe. AgNPs are made to interact with the aptamer and peptide to give different optical responses depending upon the presence or absence of malathion. The nanoparticles remain yellow in color in the absence of malathion owing to the binding of aptamer with peptide which otherwise tends to aggregate the particles because of charge based interactions. In the presence of malathion, the agglomeration of the particles occurs which turns the solution orange. Furthermore, the developed aptasensor was successfully applied to detect malathion in various water samples and apple. The detection offered high recoveries in the range of 89-120% with the relative standard deviation within 2.98-4.78%. The proposed methodology exhibited excellent selectivity and a very low limit of detection i.e. 0.5 pM was achieved. The developed facile, rapid and low cost silver nanoprobe based on aptamer and peptide proved to be potentially applicable for highly selective and sensitive colorimetric sensing of trace levels of malathion in complex environmental samples. Figure S2. HPLC Chromatogram of KKKRRR. Figure S3. UV- Visible spectra of AgNPs in the presence of increasing peptide concentrations. Inset shows respective color changes of AgNPs with peptide concentrations ranging from 0.1 mM to 100 mM (a to e). Figure S4. UV- Visible spectra of AgNPs in the presence 10 mM peptide and varying aptamer concentrations. Inset shows the corresponding color changes. a to e shows aptamer concentrations ranging from 10 nM to 1000 nM. Figure S5. Interference Studies. Ratio of A520 nm/390 nm of AgNPs in the presence of 10 mM peptide, 500 nM aptamer, 0.5 nM malathion and 0.5 mM interfering components i.e. sodium, potassium, calcium, alanine, arginine

Hazardous properties of paint residues from the furniture industry.

Science.gov (United States)

Vaajasaari, Kati; Kulovaara, Maaret; Joutti, Anneli; Schultz, Eija; Soljamo, Kari

2004-01-30

The objective of this study was to screen nine excess paint residues for environmental hazard and to evaluate their disposability in a non-hazardous or hazardous-waste landfill. These residues were produced in the process of spray-painting furniture. Residues were classified according to their leaching and ecotoxicological properties. Leaching properties were determined with the European standard SFS-EN 12457-2 leaching-test. The toxicity of the leaching-test eluates was measured with plant-, bacteria- and enzyme-inhibition bioassays. Total organic carbon, formaldehyde and solvent concentrations in the solid wastes and in the leaching-test eluates were analysed. It seemed likely that leached formaldehyde caused very high acute toxicity in leaching-test eluates of the dry-booth residues. This hypothesis was based on the fact that the formaldehyde concentrations in the leaching-test eluates of the dry-booth residues were 62-75 times higher than the EC50 value reported in the literature for formaldehyde. The results of the water-curtain booth residues showed that the samples with the highest TOC and aromatic solvent concentrations were also the most toxic. The studied excess paint residues were complex organic mixtures and contained large amounts of compounds not identifiable from chemical data. Therefore, the evaluation of the hazard based solely on available chemical data is unlikely to be sufficient, as evidenced by our study. Our results show that harmful compounds remain in the solid waste and the toxicity results of their leaching-test eluates show that toxicity may leach from residues in contact with water at landfill sites. They also confirm the benefit of combining chemical and ecotoxicological assays in assessing the potential environmental hazard of complex organic mixtures found in wastes. Copyright 2003 Elsevier B.V.

Detection of chloramphenicol residue in bovine meat using Liquid Chromatography Mass Spectrometry

Directory of Open Access Journals (Sweden)

Widiastuti R

2014-03-01

Full Text Available Chloramphenicol (CAP is a broad spectrum antibiotic that has been banned in many countries due to its serius side effect to human. Detection of CAP residue in food has been determined to a minimum required performance limit (MRPL of 0.3 ng/g. The purpose of this research was to conduct the analysis of CAP residue in bovine meat by using LCMS and to study the presence of CAP residue in marketed bovine meat samples. LC separation was done on a Shimpack column C18 with ammonium acetate 10 mM/water as mobile phase, and ESI-MS analysis in negative ion mode. The coefficient of determination, R2 = 0.9981 at concentration of 0.125, 0.25, 0.63, 1,00 and 2.00 ng/g. Recovery at three fortification levels (0.25, 0.50 and 1.00 ng/g was in the range 77.5, 97.3 and 83.4%. The decision limit and the detection capability were 0.15 ng/g and 0.17 ng/g respectively. Analysis results of 52 marketed samples showed that CAP residue were detected in 9 samples in the concentration range of 0.14 to 2.70 ng/g and 6 among those positive samples were above the MRPL value. Therefore, it is important to increase the awareness and also to monitor regularly CAP residues in food originated from animal to provide safe food for the consumers.

Effect of water-washing on the co-removal of chlorine and heavy metals in air pollution control residue from MSW incineration.

Science.gov (United States)

Yang, Zhenzhou; Tian, Sicong; Ji, Ru; Liu, Lili; Wang, Xidong; Zhang, Zuotai

2017-10-01

The present study systemically investigated the effect of a water-washing process on the removal of harmful chlorides, sulfates, and heavy metals in the air pollution control (APC) residue from municipal solid wastes incineration (MSWI), for sake of a better reuse and disposal of this kind of waste. In addition, the kinetic study was conducted to reveal the releasing mechanism of relevant element in the residue. The results show that, over 70wt.% of chlorides and nearly 25wt.% of sulfates in the residue could be removed by water washing. Based on an economical consideration, the optimal operation conditions for water washing of APC residue was at liquid/solid (L/S) ratio of 3mL:1g and extracting time of 5min. As expected, the concentrations of Co, Cr, Fe, Ni, V and Cu in the washing effluent increased with time during the washing process. However, the extracting regime differs among different heavy metals. The concentrations of Ba and Mn increased firstly but declined afterwards, and concentrations of Pb and Zn gradually declined while Cd and As kept constant with the increase of extracting time. It is worth mentioning that the bubbling of CO 2 into the washing effluent is promisingly effective for a further removal of Pb, Cu and Zn. Furthermore, kinetic study of the water washing process reveals that the extracting of heavy metals during water washing follows a second-order model. Copyright © 2017 Elsevier Ltd. All rights reserved.

In vitro residual anti-bacterial activity of difloxacin, sarafloxacin and their photoproducts after photolysis in water

International Nuclear Information System (INIS)

Kusari, Souvik; Prabhakaran, Deivasigamani; Lamshoeft, Marc; Spiteller, Michael

2009-01-01

Fluoroquinolones like difloxacin (DIF) and sarafloxacin (SARA) are adsorbed in soil and enter the aquatic environment wherein they are subjected to photolytic degradation. To evaluate the fate of DIF and SARA, their photolysis was performed in water under stimulated natural sunlight conditions. DIF primarily degrades to SARA. On prolonged photodegradation, seven photoproducts were elucidated by HR-LC-MS/MS, three of which were entirely novel. The residual anti-bacterial activities of DIF, SARA and their photoproducts were studied against a group of pathogenic strains. DIF and SARA revealed potency against both Gram-positive and -negative bacteria. The photoproducts also exhibited varying degrees of efficacies against the tested bacteria. Even without isolating the individual photoproducts, their impact on the aquatic environment could be assessed. Therefore, the present results call for prudence in estimating the fate of these compounds in water and in avoiding emergence of resistance in bacteria caused by the photoproducts of DIF and SARA. - Assessment of the residual anti-bacterial efficacies of difloxacin, sarafloxacin and their photoproducts in water, and estimating their impact on the aquatic environment in inducing resistance to microorganisms.

An Assessment of Factors Having Impact on Water Quality in Water Supply Pipelines

OpenAIRE

Auksė Amosenkienė; Marina Valentukevičienė; Aušra Mažeikienė; Raimundas Kanapickas

2011-01-01

Water samples were collected from Vilnius drinking water distribution system fed by treated and different groundwater. Parameters related to bacterial growth have been measured considering these samples: temperature, concentration of free residual chlorine, ammonium, nitrates and nitrites. Results showed that treated groundwater was less susceptible to favour bacterial growth in the pipelines. The obtained results also showed that the potential growth induced by the distribution of treated wa...

Leaching of APC residues from secondary Pb metallurgy using single extraction tests: the mineralogical and the geochemical approach.

Science.gov (United States)

Ettler, Vojtech; Mihaljevic, Martin; Sebek, Ondrej; Strnad, Ladislav

2005-05-20

Two air-pollution-control (APC) residues--one from flue gas cooling with alkaline water and one from deionized water cooling--from secondary lead metallurgy were submitted to two different standardized short-term leaching protocols: US EPA toxicity characteristic leaching procedure (TCLP) and static leaching according to Czech/European norm EN 12457-2. The experimental procedure was coupled with detailed mineralogical investigation of the solid material (SEM, XRPD) and speciation-solubility calculations using the PHREEQC-2 geochemical code. Both types of residues were considered as hazardous materials exhibiting substantial leaching of Pb (up to 7130 mg/l) and other inorganic contaminants. However, the APC residue produced by flue gas cooling with alkaline water (sample B) exhibits more favourable leaching and environmental characteristics than that produced by simple deionised water cooling (sample A). At pH 6, phosgenite (PbCl2.PbCO3) became the dominant secondary phase. The results are consistent with the mineralogical and geochemical studies focused on acidic forest soils highly polluted by smelter emissions, where anglesite, as a unique Pb-bearing phase, has been detected. From the technological point of view, the mixing of APC residue with alkaline water, followed by an increase in the suspension pH and equilibration with atmospheric CO2, may be used to ensure the precipitation of less soluble Pb carbonates, which are more easily recycled in the Pb recovery process in the metallurgical plant.

Preconcentration NAA for simultaneous multielemental determination in water sample

International Nuclear Information System (INIS)

Chatt, A.

1999-01-01

Full text: Environment concerns with water, air, land and their interrelationship viz., human beings, fauna and flora. One of the important environmental compartments is water. Elements present in water might face a whole lot of physico-chemical conditions. This poses challenges to measure their total concentrations as well as different species. Preconcentration of the elements present in water samples is a necessary requisites in water analysis. For multi elements concentration measurements, Neutron Activation Analysis (NAA) is one of the preferred analytical techniques due to its sensitivity and selectivity. In this talk preconcentration NAA for multielemental determination in water sample determination will be discussed

Enantioselective analysis of chloramphenicol residues in honey samples by chiral LC-MS/MS and results of a honey survey.

Science.gov (United States)

Rimkus, Gerhard G; Hoffmann, Dirk

2017-06-01

Chloramphenicol (CAP) is a broad-spectrum antibiotic used widely in both human and veterinary medication. Since 1994, CAP has not been authorised for use in food-producing animals in the European Union due to several adverse effects. A minimum required performance level (MRPL) of 0.3 µg kg - 1 was established in 2003. The CAP molecule contains two asymmetric centres, thus in total four para-CAP stereoisomers exist. Only the RR-CAP enantiomer is bioactive, having significant antimicrobial activity. For the first time a chiral LC-MS/MS method is reported to identify and quantify the four CAP enantiomers at residue levels in honey samples. The method was validated at two concentration levels. The decision limits (CCα) and detection capabilities (CCß) were well below 0.3 µg kg - 1 , with limits of quantification (LOQs) between 0.08 and 0.12 µg kg - 1 for all four enantiomers. The method provides a sensitive and reliable analysis of CAP enantiomers in honey, and proved its robustness during the daily routine analyses of numerous honey samples. In an internal honey survey, in total 40 honey samples from different geographical regions with identified CAP residues at or above the MRPL were reanalysed by chiral LC-MS/MS. In nine honey samples only the bioactive RR-CAP was detected as anticipated. However, in all other 31 honey samples the non-bioactive SS-CAP was also identified and quantified unambiguously. In 10 of these samples, mixtures of RR- and SS-CAP were analysed, and in 21 samples only the SS-CAP enantiomer, with concentrations up to 2.2 µg kg - 1 . Most of these samples are honeys from Ukraine and Eastern Europe. This is the first report of SS-CAP residues in food samples. The potential sources for these findings are discussed and the need of further systematic studies emphasised. It is recommended to examine in more depth the toxicological profile of the individual CAP stereoisomers.

NMR studies of stock process water and reaction pathways in hydrothermal carbonization of furfural residue

Directory of Open Access Journals (Sweden)

Fen Yue

2018-04-01

Full Text Available Hydrothermal carbonization (HTC is a valuable approach to convert furfural residue (FR into carbon material. The prepared biochars are usually characterized comprehensively, while the stock process water still remains to be studied in detail. Herein, a NMR study of the main components in stock process water generated at different HTC reaction conditions was reported. Various qualitative and quantitative NMR techniques (1H and 13C NMR, 1H–1H COSY and 1H13C HSQC etc. especially 1D selective gradient total correlation spectroscopy (TOCSY NMR were strategically applied in the analysis of HTC stock process water. Without separation and purification, it was demonstrated that the main detectable compounds are 5-hydroxymethylfurfural, formic acid, methanol, acetic acid, levulinic acid, glycerol, hydroxyacetone and acetaldehyde in this complicate mixture. Furthermore, the relationship between the concentration of major products and the reaction conditions (180–240 °C at 8 h, and 1–24 h at 240 °C was established. Finally, reasonable reaction pathways for hydrothermal conversion of FR were proposed based on this result and our previously obtained characteristics of biochars. The routine and challenging NMR methods utilized here would be an alternative other than HPLC or GC for biomass conversion research and can be extended to more studies. Keywords: NMR, Hydrothermal carbonization, Furfural residue, Stock process water

Detection of Water Contamination Events Using Fluorescence Spectroscopy and Alternating Trilinear Decomposition Algorithm

Directory of Open Access Journals (Sweden)

Jie Yu

2017-01-01

Full Text Available The method based on conventional index and UV-vision has been widely applied in the field of water quality abnormality detection. This paper presents a qualitative analysis approach to detect the water contamination events with unknown pollutants. Fluorescence spectra were used as water quality monitoring tools, and the detection method of unknown contaminants in water based on alternating trilinear decomposition (ATLD is proposed to analyze the excitation and emission spectra of the samples. The Delaunay triangulation interpolation method was used to make the pretreatment of three-dimensional fluorescence spectra data, in order to estimate the effect of Rayleigh and Raman scattering; ATLD model was applied to establish the model of normal water sample, and the residual matrix was obtained by subtracting the measured matrix from the model matrix; the residual sum of squares obtained from the residual matrix and threshold was used to make qualitative discrimination of test samples and distinguish drinking water samples and organic pollutant samples. The results of the study indicate that ATLD modeling with three-dimensional fluorescence spectra can provide a tool for detecting unknown organic pollutants in water qualitatively. The method based on fluorescence spectra can be complementary to the method based on conventional index and UV-vision.

[Detection of Cryptospordium spp. in environmental water samples by FTA-PCR].

Science.gov (United States)

Zhang, Xiao-Ping; Zhu, Qian; He, Yan-Yan; Jiang, Li; Jiang, Shou-Fu

2011-02-01

To establish a FTA-polymeras chain reaction (FTA-PCR) method in detection of Cryptospordium spp. in different sources of water. The semi automated immunomagnetic separation (IMS) of Cryptospordium oocysts in environmental water samples was performed firstly, and then genomic DNA of Cryptospordium oocysts was extracted by FTA filters disk. Oligonucleotide primers were designed based on the DNA fragment of the 18 S rRNA gene from C. parvum. Plate DNA was amplified with primers in PCR. The control DNA samples from Toxoplasma gondii,Sarcocystis suihominis, Echinococcus granulosus, and Clonorchis sinensis were amplified simultaneously. All PCR products were detected by agar electrophoresis dyed with ethidium bromide. The 446 bp fragment of DNA was detected in all samples of C. parvum, C. andersoni, and C. baileyi, while it was not detected in control groups in laboratory. No positive samples were found from 10 samples collected from tape water in 5 districts of Shanghai City by FTA-PCR. Nine positive samples were detected totally from 70 different environmental water samples, there were 0 out of 15 samples from the source of tape water, 2 out of 25 from the Huangpu River, 5 out of 15 from rivers around the animal farmers, 1 out of 9 from output water of contaminating water treatment factory, 1 out of 6 from the out gate of living contaminating water. The 446 bp fragment was detected from all the amplified positive water samples. FTA-PCR is an efficient method for gene detection of Cryptospordium oocysts, which could be used in detection of environmental water samples. The contamination degree of Cryptospordium oocysts in the river water around animal farms is high.

Total reflection x-ray analysis of metals in blood samples

International Nuclear Information System (INIS)

Nakamura, Takuya; Matsui, Hiroshi; Kawamata, Masaya

2009-01-01

The sample preparation for TXRF (total reflection X-ray fluorescence) quantitative analysis of trace elements in human blood samples was investigated. In the TXRF analysis, a solution sample is dropped and dried on a flat substrate, and then the dried residue is measured. In this case, the dried residue should be flat not to disturb X-ray total reflection on the substrate. In addition, it is required to simply measure the whole blood sample by TXRF method, although a serum is analyzed in many cases. Thus, we studied the optimum conditions of the sample preparation of the whole blood by adding the pure water to apply Hemolysis phenomenon, where blood cells are destroyed due to different of the osmotic pressure, leading to flat residue. It was found that the best S/B ratio was obtained when the whole blood was diluted 8 times with pure water. Moreover, it was investigated the influence of the surface chemical condition of the glass substrate on the shape of the dried reside of the blood sample. When the surface of the glass substrate was hydrophilic, the shape of the dried residues was not uniform, as a result, the quantitative data of TXRF analysis gave a large deviation. On the other hand, when the surface of the glass was hydrophobic, the shape of the residue was almost uniform, as a result, a good reproducibility was obtained. Another problem was an outer ring of the dried residue of the blood. This uneven ring absorbs the primary X-rays, caused to low determined quantitative data. Thus, we tried the heating way of the dropped blood sample at a high temperature of 200 degrees. In this case, the blood sample was dried immediately, and a flat homogeneous dried residue was obtained without the outer ring. Using the optimized conditions for sample preparation, human blood sample was quantitatively measured by TXRF and ICP-AES. A good agreement was obtained in TXRF and ICP-AES determinations; however, the measurement of Cl and Br will be an advantage of TXRF, because

Improved crop residue cover estimates by coupling spectral indices for residue and moisture

Science.gov (United States)

Remote sensing assessment of soil residue cover (fR) and tillage intensity will improve our predictions of the impact of agricultural practices and promote sustainable management. Spectral indices for estimating fR are sensitive to soil and residue water content, therefore, the uncertainty of estima...

Radiation degradation of pharmaceutical residues in water. Chloramphenicol

International Nuclear Information System (INIS)

Csay, T.; Racz, G.; Takacs, E.; Wojnarovits, L.

2011-01-01

Complete text of publication follows. Traditional wastewater treatment systems primarily rely upon physical, chemical and biological processes. The conventional techniques cannot efficiently remove badly biodegradable pollutants like pesticides, herbicides and drugs from influents. Leaving 'polluted' water flowing freely out to environment may cause unwanted and sometimes unpredictable effects. Degradation or removal of residual organic contaminations from wastewater is an important task both for science and engineering to preserve environment and drinking water. Ionizing radiation treatment of liquid wastes is one of the so called advanced oxidation processes (AOP) leading to decomposition of pharmaceuticals in aqueous solutions. The radiolysis of chloramphenicol (CPL) a broad spectrum antibiotic was investigated under different conditions. Steady-state gamma radiolysis were used to generate various reactive species ( · H, · OH and e aq - ). Reactions were followed by steady state and time resolved UV-Vis spectrometry. Several degradation products were separated and identified by LC-MS/MS. Mineralization was followed by measuring chemical oxygen demand (COD) and total organic carbon content (TOC). The change in toxicity was followed by Microtox, a luminescent bacteria test. Results indicate that ionizing radiation is very effective in degradation of CPL. After irradiating 0.1 mM CPL solutions with 5.0-7.5 kGy doses, no products could be observed indicating that irradiation resulted in complete mineralization.

Quantitative determination and sampling of azathioprine residues for cleaning validation in production area.

Science.gov (United States)

Fazio, Tatiana Tatit; Singh, Anil Kumar; Kedor-Hackmann, Erika Rosa Maria; Santoro, Maria Inês Rocha Miritello

2007-03-12

Cleaning validation is an integral part of current good manufacturing practices in any pharmaceutical industry. Nowadays, azathioprine and several other pharmacologically potent pharmaceuticals are manufactured in same production area. Carefully designed cleaning validation and its evaluation can ensure that residues of azathioprine will not carry over and cross contaminate the subsequent product. The aim of this study was to validate simple analytical method for verification of residual azathioprine in equipments used in the production area and to confirm efficiency of cleaning procedure. The HPLC method was validated on a LC system using Nova-Pak C18 (3.9 mm x 150 mm, 4 microm) and methanol-water-acetic acid (20:80:1, v/v/v) as mobile phase at a flow rate of 1.0 mL min(-1). UV detection was made at 280 nm. The calibration curve was linear over a concentration range from 2.0 to 22.0 microg mL(-1) with a correlation coefficient of 0.9998. The detection limit (DL) and quantitation limit (QL) were 0.09 and 0.29 microg mL(-1), respectively. The intra-day and inter-day precision expressed as relative standard deviation (R.S.D.) were below 2.0%. The mean recovery of method was 99.19%. The mean extraction-recovery from manufacturing equipments was 83.5%. The developed UV spectrophotometric method could only be used as limit method to qualify or reject cleaning procedure in production area. Nevertheless, the simplicity of spectrophotometric method makes it useful for routine analysis of azathioprine residues on cleaned surface and as an alternative to proposed HPLC method.

Emission of Carbon Dioxide Influenced by Different Water Levels from Soil Incubated Organic Residues

Science.gov (United States)

Hossain, M. B.; Puteh, A. B.

2013-01-01

We studied the influence of different organic residues and water levels on decomposition rate and carbon sequestration in soil. Organic residues (rice straw, rice root, cow dung, and poultry litter) including control were tested under moistened and flooding systems. An experiment was laid out as a complete randomized design at 25°C for 120 days. Higher CO2-C (265.45 mg) emission was observed in moistened condition than in flooding condition from 7 to 120 days. Among the organic residues, poultry litter produced the highest CO2-C emission. Poultry litter with soil mixture increased 121% cumulative CO2-C compared to control. On average, about 38% of added poultry litter C was mineralized to CO2-C. Maximum CO2-C was found in 7 days after incubation and thereafter CO2-C emission was decreased with the increase of time. Control produced the lowest CO2-C (158.23 mg). Poultry litter produced maximum cumulative CO2-C (349.91 mg). Maximum organic carbon was obtained in cow dung which followed by other organic residues. Organic residues along with flooding condition decreased cumulative CO2-C, k value and increased organic C in soil. Maximum k value was found in poultry litter and control. Incorpored rice straw increased organic carbon and decreased k value (0.003 g d−1) in soil. In conclusion, rice straw and poultry litter were suitable for improving soil carbon. PMID:24163626

Factors Affecting Transfer of Pyrethroid Residues from Herbal Teas to Infusion and Influence of Physicochemical Properties of Pesticides

Directory of Open Access Journals (Sweden)

Jin-Jing Xiao

2017-09-01

Full Text Available The transfer of pesticide residues from herbal teas to their infusion is a subject of particular interest. In this study, a multi-residue analytical method for the determination of pyrethroids (fenpropathrin, beta-cypermethrin, lambda-cyhalothrin, and fenvalerate in honeysuckle, chrysanthemum, wolfberry, and licorice and their infusion samples was validated. The transfer of pyrethroid residues from tea to infusion was investigated at different water temperatures, tea/water ratios, and infusion intervals/times. The results show that low amounts (0–6.70% of pyrethroids were transferred under the different tea brewing conditions examined, indicating that the infusion process reduced the pyrethroid content in the extracted liquid by over 90%. Similar results were obtained for the different tea varieties, and pesticides with high water solubility and low octanol–water partition coefficients (log Kow exhibited high transfer rates. Moreover, the estimated values of the exposure risk to the pyrethroids were in the range of 0.0022–0.33, indicating that the daily intake of the four pyrethroid residues from herbal tea can be regarded as safe. The present results can support the identification of suitable tea brewing conditions for significantly reducing the pesticide residue levels in the infusion.

Hotspots of soil N2O emission enhanced through water absorption by plant residue

Energy Technology Data Exchange (ETDEWEB)

Kravchenko, A.N.; Toosi, E.R.; Guber, A.K.; Ostrom, N.E.; Yu, J.; Azeem, K.; Rivers, M.L.; Robertson , G.P. (UAF Pakistan); (UC); (Hubei); (MSU)

2017-06-05

N2O is a highly potent greenhouse gas and arable soils represent its major anthropogenic source. Field-scale assessments and predictions of soil N2O emission remain uncertain and imprecise due to the episodic and microscale nature of microbial N2O production, most of which occurs within very small discrete soil volumes. Such hotspots of N2O production are often associated with decomposing plant residue. Here we quantify physical and hydrological soil characteristics that lead to strikingly accelerated N2O emissions in plant residue-induced hotspots. Results reveal a mechanism for microscale N2O emissions: water absorption by plant residue that creates unique micro-environmental conditions, markedly different from those of the bulk soil. Moisture levels within plant residue exceeded those of bulk soil by 4–10-fold and led to accelerated N2O production via microbial denitrification. The presence of large (Ø >35 μm) pores was a prerequisite for maximized hotspot N2O production and for subsequent diffusion to the atmosphere. Understanding and modelling hotspot microscale physical and hydrologic characteristics is a promising route to predict N2O emissions and thus to develop effective mitigation strategies and estimate global fluxes in a changing environment.

Monolith Chromatography as Sample Preparation Step in Virome Studies of Water Samples.

Science.gov (United States)

Gutiérrez-Aguirre, Ion; Kutnjak, Denis; Rački, Nejc; Rupar, Matevž; Ravnikar, Maja

2018-01-01

Viruses exist in aquatic media and many of them use this media as transmission route. Next-generation sequencing (NGS) technologies have opened new doors in virus research, allowing also to reveal a hidden diversity of viral species in aquatic environments. Not surprisingly, many of the newly discovered viruses are found in environmental fresh and marine waters. One of the problems in virome research can be the low amount of viral nucleic acids present in the sample in contrast to the background ones (host, eukaryotic, prokaryotic, environmental). Therefore, virus enrichment prior to NGS is necessary in many cases. In water samples, an added problem resides in the low concentration of viruses typically present in aquatic media. Different concentration strategies have been used to overcome such limitations. CIM monoliths are a new generation of chromatographic supports that due to their particular structural characteristics are very efficient in concentration and purification of viruses. In this chapter, we describe the use of CIM monolithic chromatography for sample preparation step in NGS studies targeting viruses in fresh or marine water. The step-by-step protocol will include a case study where CIM concentration was used to study the virome of a wastewater sample using NGS.

Reduction of hexavalent chromium in water samples acidified for preservation

Science.gov (United States)

Stollenwerk, K.G.; Grove, D.B.

1985-01-01

Reduction of hexavalent chromium, Cr(VI), in water samples, preserved by standard techniques, was investigated. The standard preservation technique for water samples that are to be analyzed for Cr(VI) consists of filtration through a 0.45-??m membrane, acidification to a pH plastic bottles. Batch experiments were conducted to evaluate the effect of H+ concentration, NO2, temperature, and dissolved organic carbon (DOC) on the reduction of Cr(VI) to Cr(III). The rate of reduction of Cr(VI) to Cr(III) increased with increasing NO2, DOC, H+, and temperature. Reduction of Cr(VI) by organic matter occurred in some samples even though the samples were unacidified. Reduction of Cr(VI) is inhibited to an extent by storing the sample at 4??C. Stability of Cr(VI) in water is variable and depends on the other constituents present in the sample. Water samples collected for the determination of Cr(VI) should be filtered (0.45-??m membrane), refrigerated, and analyzed as quickly as possible. Water samples should not be acidified. Measurement of total Cr in addition to Cr(VI) can serve as a check for Cr(VI) reduction. If total Cr is greater than Cr(VI), the possibility that Cr(VI) reduction has occurred needs to be considered.The rate of reduction of Cr(VI) to Cr(III) increased with increasing NO//2, DOC, H** plus , and temperature. Reduction of Cr(VI) by organic matter occurred in some samples even though the samples were unacidified. Reduction of Cr(VI) is inhibited to an extent by storing the sample at 4 degree C. Stability of Cr(VI) in water is variable and depends on the other constituents present in the sample. Water samples collected for the determination of Cr(VI) should be filtered (0. 45- mu m membrane), refrigerated, and analyzed as quickly as possible. Water samples should not be acidified. Measurement of total Cr in addition to Cr(VI) can serve as a check for Cr(VI) reduction. If total Cr is greater than Cr(VI), the possibility that Cr(VI) reduction has occurred needs

Microbial Condition of Water Samples from Foreign Fuel Storage Facilities

International Nuclear Information System (INIS)

Berry, C.J.

1998-01-01

In order to assess the microbial condition of foreign spent nuclear fuel storage facilities and their possible impact on SRS storage basins, twenty-three water samples were analyzed from 12 different countries. Fifteen of the water samples were analyzed and described in an earlier report (WSRC-TR-97-00365 [1]). This report describes nine additional samples received from October 1997 through March 1998. The samples include three from Australia, two from Denmark and Germany and one sample from Italy and Greece. Each water sample was analyzed for microbial content and activity as determined by total bacteria, viable aerobic bacteria, viable anaerobic bacteria, viable sulfate-reducing bacteria, viable acid-producing bacteria and enzyme diversity. The results for each water sample were then compared to all other foreign samples analyzed to date and monthly samples pulled from the receiving basin for off-site fuel (RBOF), at SRS. Of the nine samples analyzed, four samples from Italy, Germany and Greece had considerably higher microbiological activity than that historically found in the RBOF. This microbial activity included high levels of enzyme diversity and the presence of viable organisms that have been associated with microbial influenced corrosion in other environments. The three samples from Australia had microbial activities similar to that in the RBOF while the two samples from Denmark had lower levels of microbial activity. These results suggest that a significant number of the foreign storage facilities have water quality standards that allow microbial proliferation and survival

Sampling procedure for lake or stream surface water chemistry

Science.gov (United States)

Robert Musselman

2012-01-01

Surface waters collected in the field for chemical analyses are easily contaminated. This research note presents a step-by-step detailed description of how to avoid sample contamination when field collecting, processing, and transporting surface water samples for laboratory analysis.

Deposition behavior of residual aluminum in drinking water distribution system: Effect of aluminum speciation.

Science.gov (United States)

Zhang, Yue; Shi, Baoyou; Zhao, Yuanyuan; Yan, Mingquan; Lytle, Darren A; Wang, Dongsheng

2016-04-01

Finished drinking water usually contains some residual aluminum. The deposition of residual aluminum in distribution systems and potential release back to the drinking water could significantly influence the water quality at consumer taps. A preliminary analysis of aluminum content in cast iron pipe corrosion scales and loose deposits demonstrated that aluminum deposition on distribution pipe surfaces could be excessive for water treated by aluminum coagulants including polyaluminum chloride (PACl). In this work, the deposition features of different aluminum species in PACl were investigated by simulated coil-pipe test, batch reactor test and quartz crystal microbalance with dissipation monitoring. The deposition amount of non-polymeric aluminum species was the least, and its deposition layer was soft and hydrated, which indicated the possible formation of amorphous Al(OH)3. Al13 had the highest deposition tendency, and the deposition layer was rigid and much less hydrated, which indicated that the deposited aluminum might possess regular structure and self-aggregation of Al13 could be the main deposition mechanism. While for Al30, its deposition was relatively slower and deposited aluminum amount was relatively less compared with Al13. However, the total deposited mass of Al30 was much higher than that of Al13, which was attributed to the deposition of particulate aluminum matters with much higher hydration state. Compared with stationary condition, stirring could significantly enhance the deposition process, while the effect of pH on deposition was relatively weak in the near neutral range of 6.7 to 8.7. Copyright © 2015. Published by Elsevier B.V.

Standardization and estimation of gross alpha and beta activities for potable water samples in presence of TDS using TDCR based LSA (Hidex 300SL)

International Nuclear Information System (INIS)

Gupta, Anil; Lenka, P.; Sahoo, S.K.; Patra, A.C.; Jha, S.K.; Tripathi, R.M.

2018-01-01

Quality of water is important in environmental studies because of its daily use for human consumption and an important route of intake for various elements and radionuclides. Therefore radiological quality of drinking water must be ensured. The screening parameter to evaluate the radiological safety of potable water is by estimating gross alpha and gross beta activities with a limit of 0.5 Bq/l and 1 Bq/l respectively. These have been traditionally being done by radiochemical co-precipitation of alpha and beta emitters followed by counting by ZnS(Ag) counter for alpha and gas flow proportional counter for beta. Gross alpha estimation in water samples with high TDS by ZnS(Ag) is difficult and often leads to underestimation of result due to self-absorption of alpha within the residue. This study was carried out to standardize a method to provide rapid results by simultaneously estimating both gross alpha and gross beta activity in the presence of TDS with adequate sensitivity, minimum sample processing

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

International Nuclear Information System (INIS)

Wang, Changhui; Zhao, Yuanyuan; Pei, Yuansheng

2012-01-01

Highlights: ► Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. ► FARs cannot stabilize Ba and Cd. ► The properties of FARs and soil affect the FARs’ ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

Effect of cooking on residues of the quinolones oxolinic acid and flumequine in fish.

Science.gov (United States)

Steffenak, I; Hormazabal, V; Yndestad, M

1994-01-01

The effect of cooking on residues of the quinolones oxolinic acid and flumequine in fish was investigated. Salmon containing residues of oxolinic acid and flumequine was boiled or baked in the oven. Samples of raw and cooked muscle, skin, and bone, as well as of the water in which the fish was boiled and juice from the baked fish, were analysed. Oxolinic acid and flumequine did not degrade at the temperatures reached when cooking the fish. However, fish muscle free from drug residues may be contaminated during boiling and baking due to leakage of the drug from reservoirs in the fish.

Separation of thorium (IV) from lanthanide concentrate (LC) and water leach purification (WLP) residue

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-01-01

Thorium (IV) content in industrial residue produced from rare earth elements production industry is one of the challenges to Malaysian environment. Separation of thorium from the lanthanide concentrate (LC) and Water Leach Purification (WLP) residue from rare earth elements production plant is described. Both materials have been tested by sulphuric acid and alkaline digestions. Th concentrations in LC and WLP were determined to be 1289.7 ± 129 and 1952.9±17.6 ppm respectively. The results of separation show that the recovery of Th separation from rare earth in LC after concentrated sulphuric acid dissolution and reduction of acidity to precipitate Th was found 1.76-1.20% whereas Th recovery from WLP was less than 4% after concentrated acids and alkali digestion processes. Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) was used to determine Th concentrations in aqueous phase during separation stages. This study indicated that thorium maybe exists in refractory and insoluble form which is difficult to separate by these processes and stays in WLP residue as naturally occurring radioactive material (NORM)

Influence of quenching cooling rate on residual stress and tensile properties of 2A14 aluminum alloy forgings

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yu-xun, E-mail: zhangyuxun198@163.com; Yi, You-ping, E-mail: yyp@csu.edu.cn; Huang, Shi-quan, E-mail: huangsqcsu@sina.com; Dong, Fei

2016-09-30

To balance the quenching residual stress and the mechanical properties of aluminum alloys, the influence of cooling rate on the residual stress and tensile properties was investigated by numerical simulation and quenching experiments. During the quenching experiments, 2A14 aluminum alloy samples were treated with different water temperatures (20 °C, 70 °C, 100 °C) and a step quenching process. X-ray diffraction (XRD) was used to measure the residual stress. Prior to them, the quenching sensitivity was studied. For this purpose, the time-temperature-properties (TTP) curves were measured and the alloy microstructure was observed using transmission electron microscopy (TEM). The results indicated that the mechanical properties of 2A14 aluminum alloys were mainly determined by the cooling rate within the quenching sensitive temperature range from 300 to 400 °C. Lower cooling rates reduced the tensile strength and yield strength due to a decrease amount of fine precipitates, and reduced the residual stress with the reduction of plastic strain and the degree of inhomogeneous plastic deformation. In addition, the residual stress changed faster than the tensile properties with decreasing cooling rate. Therefore, warm water (70 °C) was used to balance the residual stress and tensile properties of 140-mm-thick 2A14 aluminum alloy forgings, since it can achieve low cooling rates. Furthermore, by combining this characteristic and the material quenching sensitivity, step quenching produced similar tensile properties and lower residual stress, compared with the sample quenched in warm water (70 °C), by increasing cooling rate within quenching sensitivity range and reducing it in other ranges.

Influence of quenching cooling rate on residual stress and tensile properties of 2A14 aluminum alloy forgings

International Nuclear Information System (INIS)

Zhang, Yu-xun; Yi, You-ping; Huang, Shi-quan; Dong, Fei

2016-01-01

To balance the quenching residual stress and the mechanical properties of aluminum alloys, the influence of cooling rate on the residual stress and tensile properties was investigated by numerical simulation and quenching experiments. During the quenching experiments, 2A14 aluminum alloy samples were treated with different water temperatures (20 °C, 70 °C, 100 °C) and a step quenching process. X-ray diffraction (XRD) was used to measure the residual stress. Prior to them, the quenching sensitivity was studied. For this purpose, the time-temperature-properties (TTP) curves were measured and the alloy microstructure was observed using transmission electron microscopy (TEM). The results indicated that the mechanical properties of 2A14 aluminum alloys were mainly determined by the cooling rate within the quenching sensitive temperature range from 300 to 400 °C. Lower cooling rates reduced the tensile strength and yield strength due to a decrease amount of fine precipitates, and reduced the residual stress with the reduction of plastic strain and the degree of inhomogeneous plastic deformation. In addition, the residual stress changed faster than the tensile properties with decreasing cooling rate. Therefore, warm water (70 °C) was used to balance the residual stress and tensile properties of 140-mm-thick 2A14 aluminum alloy forgings, since it can achieve low cooling rates. Furthermore, by combining this characteristic and the material quenching sensitivity, step quenching produced similar tensile properties and lower residual stress, compared with the sample quenched in warm water (70 °C), by increasing cooling rate within quenching sensitivity range and reducing it in other ranges.

Analysis of s-triazine herbicides in model systems and samples of groundwater by gas and liquid chromatography

Directory of Open Access Journals (Sweden)

Kostadinović Ljiljana

2010-01-01

Full Text Available In this paper, residues of s-triazine herbicides (Simazine, Atrazine, Amethrine, Promethrine and Azyprothrine have been determined in samples of model systems and real groundwater samples by gas-chromatography and high performance liquid chromatography. S-triazine herbicides were isolated from water samples by chloroform-methanol mixture (1:1, followed by purification of extract on the Al2O3 column. Gas-chromatographic determination the residues of s-triazines is performed on parallel capilar columns ULTRA I and ULTRA II, using specific NP detector. Liquid-chromatographic determination the s-triazines was performed on the column TSK ODS-120 A 5 mm 'LKB', using the mobile phase methanol-water (60:40. Total concentration of s-triazines in samples of Danube water was 3.54 mg dm-3. .

Analytical study on the determination of boron in environmental water samples

International Nuclear Information System (INIS)

Lopez, F.J.; Gimenez, E.; Hernandez, F.

1993-01-01

An analytical study on the determination of boron in environmental water samples was carried out. The curcumin and carmine standard methods were compared with the most recent Azomethine-H method in order to evaluate their analytical characteristics and feasibility for the analysis of boron in water samples. Analyses of synthetic water, ground water, sea water and waste water samples were carried out and a statistical evaluation of the results was made. The Azomethine-H method was found to be the most sensitive (detection limit 0.02 mg l -1 ) and selective (no interference of commonly occurring ions in water was observed), showing also the best precision (relative standard deviation lower than 4%). Moreover, it gave good results for all types of samples analyzed. The accuracy of this method was tested by the addition of known amounts of standard solutions to different types of water samples. The slopes of standard additions and direct calibration graphs were similar and recoveries of added boron ranged from 99 to 107%. (orig.)

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

Science.gov (United States)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-02-01

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) & 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) &29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted.

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-01-01

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232 Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted

Thorium, Uranium and Rare Earth Elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas Advanced Materials Plant (LAMP)

International Nuclear Information System (INIS)

Al-Areqi, W.M.; Amran Abdul Majid; Sukiman Sarmani

2013-01-01

Full-text: Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6 Bq/ kg) whereas the Th and U concentrations in WLP were determined to be 1952.9 ± 17.6 ppm (7987.4 ± 71.9 Bq/ kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/ kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/ kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of 232 Th compared to Malaysian soil natural background (63 - 110 Bq/ kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6 % and 4.7 ± 0.1 % respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04 %, 1.6 %, 0.22 % and 0.06 % respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be re

Thorium, uranium and rare earth elements content in lanthanide concentrate (LC) and water leach purification (WLP) residue of Lynas advanced materials plant (LAMP)

Energy Technology Data Exchange (ETDEWEB)

AL-Areqi, Wadeeah M., E-mail: walareqi@yahoo.com; Majid, Amran Ab., E-mail: walareqi@yahoo.com; Sarmani, Sukiman, E-mail: walareqi@yahoo.com [Nuclear Science Programme, School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi (Malaysia)

2014-02-12

Lynas Advanced Materials Plant (LAMP) has been licensed to produce the rare earths elements since early 2013 in Malaysia. LAMP processes lanthanide concentrate (LC) to extract rare earth elements and subsequently produce large volumes of water leach purification (WLP) residue containing naturally occurring radioactive material (NORM). This residue has been rising up the environmental issue because it was suspected to accumulate thorium with significant activity concentration and has been classified as radioactive residue. The aim of this study is to determine Th-232, U-238 and rare earth elements in lanthanide concentrate (LC) and water leach purification (WLP) residue collected from LAMP and to evaluate the potential radiological impacts of the WLP residue on the environment. Instrumental Neutron Activation Analysis and γ-spectrometry were used for determination of Th, U and rare earth elements concentrations. The results of this study found that the concentration of Th in LC was 1289.7 ± 129 ppm (5274.9 ± 527.6Bq/kg) whereas the Th and U concentrations in WLP were determined to be 1952.9±17.6 ppm (7987.4 ± 71.9 Bq/kg) and 17.2 ± 2.4 ppm respectively. The concentrations of Th and U in LC and WLP samples determined by γ- spectrometry were 1156 ppm (4728 ± 22 Bq/kg) and 18.8 ppm and 1763.2 ppm (7211.4 Bq/kg) and 29.97 ppm respectively. This study showed that thorium concentrations were higher in WLP compare to LC. This study also indicate that WLP residue has high radioactivity of {sup 232}Th compared to Malaysian soil natural background (63 - 110 Bq/kg) and come under preview of Act 304 and regulations. In LC, the Ce and Nd concentrations determined by INAA were 13.2 ± 0.6% and 4.7 ± 0.1% respectively whereas the concentrations of La, Ce, Nd and Sm in WLP were 0.36 ± 0.04%, 1.6%, 0.22% and 0.06% respectively. This result showed that some amount of rare earth had not been extracted and remained in the WLP and may be considered to be reextracted.

Residual water transport in the Marsdiep tidal inlet inferred from observations and a numerical model

NARCIS (Netherlands)

Sassi, M.G.; Gerkema, T.; Duran-Matute, M.; Nauw, J.J.

2016-01-01

At tidal inlets, large amounts of water are exchanged with the adjacent sea during the tidal cycle.The residual flows, the net effect of ebb and flood, are generally small compared with the gross flux;they vary in magnitude and sign from one tidal period to the other; and their long-term mean

Residual water transport in the Marsdiep tidal inlet inferred from observations and a numerical model

NARCIS (Netherlands)

Sassi, M.G.; Gerkema, T.; Duran-Matute, M.; Nauw, J.J.

At tidal inlets, large amounts of water are exchanged with the adjacent sea during the tidal cycle. The residual flows, the net effect of ebb and flood, are generally small compared with the gross flux; they vary in magnitude and sign from one tidal period to the other; and their long-term mean

Polder effects on sediment-to-soil conversion: water table, residual available water capacity, and salt stress interdependence.

Science.gov (United States)

Radimy, Raymond Tojo; Dudoignon, Patrick; Hillaireau, Jean Michel; Deboute, Elise

2013-01-01

The French Atlantic marshlands, reclaimed since the Middle Age, have been successively used for extensive grazing and more recently for cereal cultivation from 1970. The soils have acquired specific properties which have been induced by the successive reclaiming and drainage works and by the response of the clay dominant primary sediments, that is, structure, moisture, and salinity profiles. Based on the whole survey of the Marais Poitevin and Marais de Rochefort and in order to explain the mechanisms of marsh soil behavior, the work focuses on two typical spots: an undrained grassland since at least 1964 and a drained cereal cultivated field. The structure-hydromechanical profiles relationships have been established thanks to the clay matrix shrinkage curve. They are confronted to the hydraulic functioning including the fresh-to-salt water transfers and to the recording of tensiometer profiles. The CE1/5 profiles supply the water geochemical and geophysical data by their better accuracy. Associated to the available water capacity calculation they allow the representation of the parallel evolution of the residual available water capacity profiles and salinity profiles according to the plant growing and rooting from the mesophile systems of grassland to the hygrophile systems of drained fields.

Structural analysis on mutation residues and interfacial water molecules for human TIM disease understanding

Science.gov (United States)

2013-01-01

Background Human triosephosphate isomerase (HsTIM) deficiency is a genetic disease caused often by the pathogenic mutation E104D. This mutation, located at the side of an abnormally large cluster of water in the inter-subunit interface, reduces the thermostability of the enzyme. Why and how these water molecules are directly related to the excessive thermolability of the mutant have not been investigated in structural biology. Results This work compares the structure of the E104D mutant with its wild type counterparts. It is found that the water topology in the dimer interface of HsTIM is atypical, having a "wet-core-dry-rim" distribution with 16 water molecules tightly packed in a small deep region surrounded by 22 residues including GLU104. These water molecules are co-conserved with their surrounding residues in non-archaeal TIMs (dimers) but not conserved across archaeal TIMs (tetramers), indicating their importance in preserving the overall quaternary structure. As the structural permutation induced by the mutation is not significant, we hypothesize that the excessive thermolability of the E104D mutant is attributed to the easy propagation of atoms' flexibility from the surface into the core via the large cluster of water. It is indeed found that the B factor increment in the wet region is higher than other regions, and, more importantly, the B factor increment in the wet region is maintained in the deeply buried core. Molecular dynamics simulations revealed that for the mutant structure at normal temperature, a clear increase of the root-mean-square deviation is observed for the wet region contacting with the large cluster of interfacial water. Such increase is not observed for other interfacial regions or the whole protein. This clearly suggests that, in the E104D mutant, the large water cluster is responsible for the subunit interface flexibility and overall thermolability, and it ultimately leads to the deficiency of this enzyme. Conclusions Our study

Chemical and microbiological analysis of public school water in Uberaba Municipality

Directory of Open Access Journals (Sweden)

Sérgio Marcos Sanches

2015-07-01

Full Text Available This study evaluated the quality of water consumed by schoolchildren in the city of Uberaba, relying upon chemical analyzes to determine the levels of free-residual chlorine and levels of chromium, copper, manganese, lead and cadmium. Microbiological analysis was also performed in order to determine total coliforms and Escherichia coli, using the values established by Ordinance n0 . 2914 of 2011 of the Ministry of Health as parameters for safe drinking water. Water samples were analyzed from the drinking fountains and kitchen faucets of eight public schools that serve children aged 0-5 years. Sampling was conducted quarterly from December 2011 to September 2012, resulting in four collections. The results revealed the presence of Escherichia coli and total coliforms above the valued permitted by legislation in more than 50% of the samples. It was also observed that concentrations of free-residual chlorine were below the minimum value required by law in nearly half of the samples analyzed. In relation to the concentration of metals, some samples had water contents of copper, cadmium, chromium, manganese and lead above the permissible levels. Statistical tests revealed that when analyzing the period of sampling, only the values for the concentrations of free-residual chlorine, chromium and lead showed no significant difference (p> 0.05. The results show the need for corrective actions at the water supply point for the school population, in addition to monitoring and controlling the quality of water for human consumption.

UMTRA project water sampling and analysis plan, Monument Valley, Arizona

International Nuclear Information System (INIS)

1994-04-01

The Monument Valley Uranium Mill Tailings Remedial Action (UMTRA) Project site in Cane Valley is a former uranium mill that has undergone surface remediation in the form of tailings and contaminated materials removal. Contaminated materials from the Monument Valley (Arizona) UMTRA Project site have been transported to the Mexican Hat (Utah) UMTRA Project site for consolidation with the Mexican Hat tailings. Tailings removal was completed in February 1994. Three geologic units at the site contain water: the unconsolidated eolian and alluvial deposits (alluvial aquifer), the Shinarump Conglomerate (Shinarump Member), and the De Chelly Sandstone. Water quality analyses indicate the contaminant plume has migrated north of the site and is mainly in the alluvial aquifer. An upward hydraulic gradient in the De Chelly Sandstone provides some protection to that aquifer. This water sampling and analysis plan recommends sampling domestic wells, monitor wells, and surface water in April and September 1994. The purpose of sampling is to continue periodic monitoring for the surface program, evaluate changes to water quality for site characterization, and provide data for the baseline risk assessment. Samples taken in April will be representative of high ground water levels and samples taken in September will be representative of low ground water levels. Filtered and nonfiltered samples will be analyzed for plume indicator parameters and baseline risk assessment parameters

Organochlorine pesticide residues in sardinella aurita from the coastal waters of Accra-Tema, Ghana and their potential health risks

International Nuclear Information System (INIS)

Nyarko, E.; Botwe, B.O.; Bampoe, A.A.; Addo, S.; Armah, A.K.; Ntow, W.J.; Kelderman, P.

2011-01-01

Sardinella aurita and seawater samples from the Accra-Tema coast of Ghana were analysed for organochlorine (OC) pesticides using gas chromatography (GC) with electron capture detection (ECD). Residues of DDTs (p,p'-DDT, p'p'-DDE,p,p'-DDD), hexachlorocyclohexane (HCHs - α-HCH, β-HCH and γ-HCH), endosulfan (α-endosulfan, β-endosulfan, endosulfan sulphate) and heptachlor were detected in fish at average concentrations ranging from 3.0 to 1235.0 μg/kg wet wt. These residues were, however, below the detection limit in seawater samples. Significant differences (p < 0.05) in residue levels were also observed across sites, decreasing from Chorkor to Kpone for seven (7) of the residues that were detected in S. aurita. Evaluation of hazard ratios (HRs) and the health risk associated with OC exposure from consumption of sardinellas revealed a probability of adverse health effect due to p,p'-DDT, γ-HCH and heptachlor. Hence, p,p'-DDT, γ-HCH and heptachlor may be of particular health concern. (au)

Recycling of drinking water treatment residue as an additional medium in columns for effective P removal from eutrophic surface water.

Science.gov (United States)

Wang, Changhui; Wu, Yu; Bai, Leilei; Zhao, Yaqian; Yan, Zaisheng; Jiang, Helong; Liu, Xin

2018-07-01

This study assesses the feasibility of recycling drinking water treatment residue (DWTR) to treat eutrophic surface water in a one-year continuous flow column test. Heat-treated DWTR was used as an additional medium (2%-4%) in columns in case excessive organic matter and N were released from the DWTR to surface water. The results indicated that with minimal undesirable effects on other water properties, DWTR addition substantially enhanced P removal, rendering P concentrations in treated water oligotrophic and treated water unsuitable for Microcystis aeruginosa breeding. Long-term stable P removal by DWTR-column treatment was mainly attributed to the relatively low P levels in raw water (cycles and multiple pollution control (e.g., Dechloromonas, Geobacter, Leucobacter, Nitrospira, Rhodoplanes, and Sulfuritalea); an apparent decrease in Mycobacterium with potential pathogenicity was observed in DWTR-columns. Regardless, limited denitrification of DWTR-columns was observed as a result of low bioavailability of C in surface water. This finding indicates that DWTR can be used with other methods to ensure denitrification for enhanced treatment effects. Overall, the use of DWTR as an additional medium in column systems can potentially treat eutrophic surface water. Copyright © 2018 Elsevier Ltd. All rights reserved.

Assessment of Atrazine contamination in water and soil in Ghana: A preliminary study in the Yilo Krobo and Mfantsiman Districts

International Nuclear Information System (INIS)

Darku, E. K.

2013-07-01

The thesis presents a study to determine the levels of atrazine in water and soil samples in selected farming communities in the Central and Eastern regions of Ghana, and provide baseline information on the contamination levels using high performance liquid chromatography (HPLC). Instrumental Nuclear Activation Analysis (INAA) was used for the determination of concentration of chlorine residue in all the atrazine extracts. Twenty-four (24) water samples, comprising twelve (12) each from Obawale and Bafikrom farming communities and their environs in the Eastern and Central Regions respectively and sixteen (16) soil samples from farms in the same location. Solid-phase extraction C 18 Sep-Pak cartridges were used for the isolation of atrazine residues from water samples in this investigation. Methanol (HPLC grade) was used to elute the atrazine, concentrated and transferred into vials for the determination of the atrazine contents. The same procedure was used for the determination of atrazine in soil samples using acetonitrile for the extraction. Residue of atrazine was detected in all water samples from Obawale with concentration ranging from 0.012 to 0.042µg/L with a mean concentration of 0.026µg/L whilst that of Baifikrom ranged from 0.01 to 0.04µg/L with a mean value of 0.007µg/L. Residue of atrazine was detected in ground water samples from Obawale with concentration ranging from 0.030µg/L to 0.930µg/L and from 0.038µg/L to 0.116µg/L at Bafikrom. The relative higher concentration of atrazine in the ground water sample was ro be expected since atrazine tend to be more stable in ground water. For soil samples, 8 out of the 16 samples recorded atrazine residue. For Obawale and Baifikrom, residues were detected in 5 and 3 samples ranging from 0.011µg/L to 0.041µg/L and 0.001µg/L to 0.009µg/L respectively. Using the INAA, concentration of chlorine residue was detected in all the atrazine extracts. The chlorine values ranged from 0.004µg/L to 0.01µg/L. In

Zirconium(IV) functionalized magnetic nanocomposites for extraction of organophosphorus pesticides from environmental water samples.

Science.gov (United States)

Jiang, Li; Huang, Tengjun; Feng, Shun; Wang, Jide

2016-07-22

The widespread use of organophosphate pesticides (OPPs) in agriculture leads to residue accumulation in the environment which is dangerous to human health and disrupts the ecological balance. In this work, one nanocomposite immobilized zirconium (Zr, IV) was prepared and used as the affinity probes to quickly and selectively extract organophosphorus pesticides (OPPs) from water samples. The Fe3O4-ethylenediamine tetraacetic acid (EDTA)@Zr(IV) nanocomposites (NPs) were prepared by simply mixing Zr(IV) ions with Fe3O4-EDTA NPs synthesized by one-pot chemical co-precipitation method. The immobilized Zr(IV) ions were further utilized to capture OPPs based on their high affinity for the phosphate moiety in OPPs. Coupled with GC-MS, four OPPs were used as models to demonstrate the feasibility of this approach. Under the optimum conditions, the limits of detection for target OPPs were in the range of 0.10-10.30ngmL(-1) with relative standard deviations (RSDs) of 0.61-4.40% (n=3), respectively. The linear ranges were over three orders of magnitudes (correlation coefficients, R(2)>0.9995). The Fe3O4-EDTA@Zr(IV) NPs were successfully applied to extract OPPs samples with recoveries of 86.95-112.60% and RSDs of 1.20-10.42% (n=3) from two spiked real water. By the proposed method, the matrix interference could be effectively eliminated. We hope our finding can provide a promising alternative for the fast extraction of OPPs from complex real samples. Copyright © 2016 Elsevier B.V. All rights reserved.

PIXE analysis applied to characterized water samples

International Nuclear Information System (INIS)

Santos, Maristela S.; Carneiro, Luana Gomes; Medeiros, Geiza; Sampaio, Camilla; Martorell, Ana Beatriz Targino; Gouvea, Stella; Cunha, Kenya Moore Dias da

2011-01-01

Araxa, in Brazil, is a naturally high background area located in the State of Minas Gerais with a population of about 93 672 people. Araxa is historical city famous for its mineral water sources and mud from Termas de Araxa spa, which have been used for therapeutic, and recreation purposes. Other important aspect of economy of the city are mining and metallurgic industries. In the Araxa area is located the largest deposit of pyrochlore, a niobium mineral, and also a deposit of apatite, a phosphate mineral both containing Th and U associated to crystal lattice. The minerals are obtained from open pit mines, the minerals are processed in industrial also located in city of Araxa, these plants process the pyrochlore and apatite to obtain the Fe-Nb alloy and the concentrate of phosphate, respectively. Studies were developed in this area to assessment the occupational risk of the workers due to exposure to dust particles during the routine working, however very few studies evaluated the water contamination outside the mines in order to determine the metal (stables elements) concentrations in water and also the concentrations of the radionuclides in water. This paper presents the previous results of a study to identify and determine the concentrations of metals (stables elements) and radionuclides in river around the city. The water from these rivers is used as drinking water and irrigation water. The water samples were collected in different rivers around the Araxa city and the samples were analyzed using PIXE technique. A proton beam of 2 MeV obtained from the van de Graaff electrostatic accelerator was used to induce the characteristic X-rays. S, K, Ca, Cr, Mn, Fe, Ni, Zn, Ba, Pb and U were identified in the mass spectrum of the samples. The elemental mass concentrations were compared using a non-parametric statistical test. The results of the statistical test showed that the elemental mass concentrations did not present the same distribution. These results indicated

Residual radioactivity guidelines for the heavy water components test reactor at the Savannah River Site

International Nuclear Information System (INIS)

Owen, M.B. Smith, R.; McNeil, J.

1997-04-01

Guidelines were developed for acceptable levels of residual radioactivity in the Heavy Water Components Test Reactor (HWCTR) facility at the conclusion of its decommissioning. Using source terms developed from data generated in a detailed characterization study, the RESRAD and RASRAD-BUILD computer codes were used to calculate derived concentration guideline levels (DCGLs) for the radionuclides that will remain in the facility. The calculated DCGLs, when compared to existing concentrations of radionuclides measured during a 1996 characterization program, indicate that no decontamination of concrete surfaces will be necessary. Also, based on the results of the calculations, activated concrete in the reactor biological shield does not have to be removed, and imbedded radioactive piping in the facility can remain in place. Viewed in another way, the results of the calculations showed that the present inventory of residual radioactivity in the facility (not including that associated with the reactor vessel and steam generators) would produce less than one millirem per year above background to a hypothetical individual on the property. The residual radioactivity is estimated to be approximately 0.04 percent of the total inventory in the facility as of March, 1997. According to the results, the only radionuclides that would produce greater than 0.0.1-millirem per year are Am-241 (0.013 mrem/yr at 300 years), C-14 (0.022 mrem/yr at 1000 years) and U-238 (0.034 mrem/yr at 6000 years). Human exposure would occur only through the groundwater pathways, that is, from water drawn from, a well on the property. The maximum exposure would be approximately one percent of the 4 millirem per year ground water exposure limit established by the U.S. Environmental Protection Agency. 11 refs., 13 figs., 15 tabs

Mass transfer of H2O between petroleum and water: implications for oil field water sample quality

International Nuclear Information System (INIS)

McCartney, R.A.; Ostvold, T.

2005-01-01

Water mass transfer can occur between water and petroleum during changes in pressure and temperature. This process can result in the dilution or concentration of dissolved ions in the water phase of oil field petroleum-water samples. In this study, PVT simulations were undertaken for 4 petroleum-water systems covering a range of reservoir conditions (80-185 o C; 300-1000 bar) and a range of water-petroleum mixtures (volume ratios of 1:1000-300:1000) to quantify the extent of H 2 O mass transfer as a result of pressure and temperature changes. Conditions were selected to be relevant to different types of oil field water sample (i.e. surface, downhole and core samples). The main variables determining the extent of dilution and concentration were found to be: (a) reservoir pressure and temperature, (b) pressure and temperature of separation of water and petroleum, (c) petroleum composition, and (d) petroleum:water ratio (PWR). The results showed that significant dilution and concentration of water samples could occur, particularly at high PWR. It was not possible to establish simple guidelines for identifying good and poor quality samples due to the interplay of the above variables. Sample quality is best investigated using PVT software of the type used in this study. (author)

Water sampling device for detecting fuel failure

International Nuclear Information System (INIS)

Masubuchi, Yukio.

1997-01-01

A notched portion is formed at the lower end of an outer cap, and an extensible air bag is disposed being in contact with the inner side of the notched portion. A compressed air is sent into the outer gap through an air supply pipe to urge coolants thereby lowering the water level. A portion of the compressed air gets out of the outer gap from the notched portion, and if air bubbles are observed on the surface of coolants in a pressure vessel of a reactor, the outer cap is confirmed to be attached to the upper lattice plate. Compressed air is supplied to the air bag to close the notched portion. Then, coolants are sucked from a water level confirmation pipe. The level of coolants is further lowered, and the compressed air is sucked from the water level confirmation pipe instead of the coolants. Then, the level of the coolants at the inner side of the inner cap is confirmed to be made lower than the upper end of the channel box of a reactor fuel assembly. Then, coolants in the channel box are sampled, as a specimen water, through a water sampling pipe. (I.N.)

Addition of an organic amendment and/or residue mud to bauxite residue sand in order to improve its properties as a growth medium.

Science.gov (United States)

Jones, B E H; Haynes, R J; Phillips, I R

2012-03-01

The effects of addition of carbonated residue mud (RMC) or seawater neutralized residue mud (RMS), at two rates, in the presence or absence of added green waste compost, on the chemical, physical and microbial properties of gypsum-treated bauxite residue sand were studied in a laboratory incubation study. The growth of two species commonly used in revegetation of residue sand (Lolium rigidum and Acacia saligna) in the treatments was then studied in a 18-week greenhouse study. Addition of green waste-based compost increased ammonium acetate-extractable (exchangeable) Mg, K and Na. Addition of residue mud at 5 and 10% w/w reduced exchangeable Ca but increased that of Mg and Na (and K for RMS). Concentrations of K, Na, Mg and level of EC in saturation paste extracts were increased by residue mud additions. Concentrations of cations in water extracts were considerably higher than those in saturation paste extracts but trends with treatment were broadly similar. Addition of both compost and residue mud caused a significant decrease in macroporosity with a concomitant increase in mesoporosity and microporosity, available water holding capacity and the quantity of water held at field capacity. Increasing rates of added residue mud reduced the percentage of sample present as discrete sand particles and increased that in aggregated form (particularly in the 1-2 and >10mm diameter ranges). Organic C content, C/N ratio, soluble organic C, microbial biomass C and basal respiration were increased by compost additions. Where compost was added, residue mud additions caused a substantial increase in microbial biomass and basal respiration. L. rigidum grew satisfactorily in all treatments although yields tended to be reduced by additions of mud (especially RMC) particularly in the absence of added compost. Growth of A. saligna was poor in sand alone and mud-amended sand and was greatly promoted by additions of compost. However, in the presence of compost, addition of carbonated

Determining the Release of Radionuclides from Tank 18F Waste Residual Solids: FY2016 Report

Energy Technology Data Exchange (ETDEWEB)

King, William D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-08-12

Pore water leaching studies were conducted on actual Savannah River Site (SRS) Tank 18F residual waste solids to support Liquid Waste tank closure efforts. A test methodology was developed during previous simulant testing to produce slurries of tank residual solids and grout-representative solids in grout pore water solutions (based on SRS groundwater compositions) with pH and E_h values expected during the aging of the closed waste tank. The target conditions are provided below where the initial pore water has a reducing potential and a relatively high pH (Reducing Region II). The pore water is expected to become increasingly oxidizing with time (Oxidizing Region II) and during the latter stages of aging (Oxidizing Region III) the pH is expected to decrease. For the reducing case, tests were conducted with both unwashed and washed Tank 18F residual solids. For the oxidizing cases (Oxidizing Regions II and III), all samples were washed with simulated grout pore water solutions prior to testing, since it is expected that these conditions will occur after considerable pore water solution has passed through the system. For the reducing case, separate tests were conducted with representative ground grout solids and with calcium carbonate reagent, which is the grout phase believed to be controlling the pH. Ferrous sulfide (FeS) solids were also added to the reducing samples to lower the slurry E_h value. Calcium carbonate solids were used as the grout-representative solid phase for each of the oxidizing cases. Air purge-gas with and without CO₂ removed was transferred through the oxidizing test samples and nitrogen purge-gas was transferred through the reducing test samples during leach testing. The target pH values were achieved to within 0.5 pH units for all samples. Leaching studies were conducted over an E_h range of approximately 0.7 V. However, the highest and lowest E_h values achieved of ~+0.5 V and ~-0.2 V were

UMTRA project water sampling and analysis plan, Tuba City, Arizona

International Nuclear Information System (INIS)

1996-02-01

Planned, routine ground water sampling activities at the U.S. Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site in Tuba City, Arizona, are described in the following sections of this water sampling and analysis plan (WSAP). This plan identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the stations routinely monitored at the site. The ground water data are used for site characterization and risk assessment. The regulatory basis for routine ground water monitoring at UMTRA Project sites is derived from the U.S. Environmental Protection Agency (EPA) regulations in 40 CFR Part 192 (1994) and the final EPA standards of 1995 (60 FR 2854). Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), and the most effective technical approach for the site

Water quality effects of intermittent water supply in Arraiján, Panama.

Science.gov (United States)

Erickson, John J; Smith, Charlotte D; Goodridge, Amador; Nelson, Kara L

2017-05-01

Intermittent drinking water supply is common in low- and middle-income countries throughout the world and can cause water quality to degrade in the distribution system. In this study, we characterized water quality in one study zone with continuous supply and three zones with intermittent supply in the drinking water distribution network in Arraiján, Panama. Low or zero pressures occurred in all zones, and negative pressures occurred in the continuous zone and two of the intermittent zones. Despite hydraulic conditions that created risks for backflow and contaminant intrusion, only four of 423 (0.9%) grab samples collected at random times were positive for total coliform bacteria and only one was positive for E. coli. Only nine of 496 (1.8%) samples had turbidity >1.0 NTU and all samples had ≥0.2 mg/L free chlorine residual. In contrast, water quality was often degraded during the first-flush period (when supply first returned after an outage). Still, routine and first-flush water quality under intermittent supply was much better in Arraiján than that reported in a previous study conducted in India. Better water quality in Arraiján could be due to better water quality leaving the treatment plant, shorter supply outages, higher supply pressures, a more consistent and higher chlorine residual, and fewer contaminant sources near pipes. The results illustrate that intermittent supply and its effects on water quality can vary greatly between and within distribution networks. The study also demonstrated that monitoring techniques designed specifically for intermittent supply, such as continuous pressure monitoring and sampling the first flush, can detect water quality threats and degradation that would not likely be detected with conventional monitoring. Copyright © 2017 Elsevier Ltd. All rights reserved.

Amendment of arsenic and chromium polluted soil from wood preservation by iron residues from water treatment

DEFF Research Database (Denmark)

Nielsen, Sanne Skov; Petersen, L. R.; Kjeldsen, Peter

2011-01-01

An iron-rich water treatment residue (WTR) consisting mainly of ferrihydrite was used for immobilization of arsenic and chromium in a soil contaminated by wood preservatives. A leaching batch experiment was conducted using two soils, a highly contaminated soil (1033mgkg−1 As and 371mgkg−1 Cr....... Pore water was extracted during 3years from the amended soil and a control site. Pore water arsenic concentrations in the amended soil were more than two orders of magnitude lower than in the control for the upper samplers. An increased release of arsenic was observed during winter in both fields...

Residues of 2, 4-D in air samples from Saskatchewan: 1966-1975.

Science.gov (United States)

Grover, R; Kerr, L A; Wallace, K; Yoshida, K; Maybank, J

1976-01-01

Residues of 2,4-D (2,4-dichlorophenoxyacetic acid) in air samples from several sampling sites in central and southern Saskatchewan during the spraying seasons in the 1966-68 and 1970-75 periods were determined by gas-liquid chromatographic techniques. Initially, individual esters of 2,4-D were characterized by retention times and confirmed further by co-injection and dual column procedures. Since 1973, however, only total 2,4-D acid levels in air samples have been determined after esterification to the methyl ester and confirmed by gc/ms techniques whenever possible. Up to 50% of the daily samples collected during the spraying season at any of the locations and during any given year contained 2,4-D, with butyl esters being found most frequently. The daily 24-hr mean atmospheric concentrations of 2,4-D ranged from 0.01 to 1.22 mug/m3, 0.01 to 13.50 mug/m3, and 0.05 to 0.59 mug/m3 for the iso-propyl, mixed butyl and iso-octyl esters, respectively. Even when the samples were analysed for the total 2,4-D content, i.e. from 1973 onwards, the maximum level of the total acid reached only 23.14 mug/m3. In any given year and at any of the sampling sites, about 30% of the samples contained less than 0.01 mug/m3 of 2,4-D. In another 40% of the samples, the levels of 2,4-D ranged from 0.01 to 0.099 mug/m3. Only about 30% of the samples contained 2,4-D concentrations higher than 0.1 mug/m3, with only 10% or less exceeding 1 mug/m3. None of the samples, obtained with the high volume particulate sampler, showed any detectable levels of 2,4-D, indicating little or no transport of 2,4-D adsorbed on dust particles or as crystals of amine salts.

Content Of 2,4-D-14C Herbicide Residue In Water And Soil Of Irrigated Rice Field System

International Nuclear Information System (INIS)

Chairul, Sofnie M.; Djabir, Elida; Magdalena, Nelly

2000-01-01

The investigation of 2,4-D exp.-14C herbicide residue in water and soil of irrigated rice field system was carried out. Rice plant and weeds (Monochoria vaginalis Burn. F. Presl) were planted in 101 buckets using two kinds of soil condition, I.e. normal soil and 30 % above normal compact soil. After one week planting, the plants were sprayed with 1 u Ci of 2,4-D exp.-14C and 0,4 mg non labeled 2,4-D. The herbicide residue content was determined 0, 2, 4, 8 and 10 weeks after spraying with 2,4-D herbicide. The analysis was done using Combustion Biological Oxidizer merk Harvey ox-400, and counted with Liquid Scintillation Counter merk Beckman model LS-1801. The results indicates that the herbicide contents in water and soil decrease from the first spraying with herbicide until harvest herbicide Residue content in water after harvest was 0.87 x 10 exp.-6 ppm for soil normal condition, and 0.59 x 10 exp.-6 pm for the soil 30 % up normal condition, while herbicide content in soil was 1.54 x 10 exp.-6 ppm for soil normal condition and 1.48 x 10 exp.-6 ppm for soil 30 % up normal. 2,4-D herbicide residue content in rice after harvest was 0.27 x 10 exp.-6 ppm for normal soil condition and 0.25 x 10 exp.-6 ppm for the soil 30 % up normal. 2,4-D herbicide residue content in roots and leaves of weeds after harvest were respectively 0.29 x 10 exp.-6 ppm and 0.18 x 10 exp.-6 for normal soil condition, while for 30 % up normal soil were 0.25 x 10 exp.-5 ppm and 0.63 x 10 exp.-7 ppm. This result indicates that there is no effect pollution to surrounding area, because the herbicide content is still bellow the allowed detection limit, 0.05 ppm

Removal of uranyl ions from residual waters using some algae types

International Nuclear Information System (INIS)

Cecal, A.; Palamaru, I.; Humelnicu, D.; Popa, K.; Salaru, V.V.; Rudic, V.; Gulea, A.

1999-01-01

This paper deals with a study on the bioaccumulation of uranyl ions resulted from residual effluents by means of some microbiological collectors: Scenedesmus quadricauda, Anabaena karakumica, Calothrix brevissima, Penicillinium sp, as well as the Glucid extract of Porphyridium cruentum, under various experimental conditions. The retaining degree of the bioaccumulated uranyl ions, as well as the leaching degree, in HCl and H 2 O media, of the same ions previously retained on algae were established. The retaining degree decreases in the series: Scenedesmus quadricauda > Anabaena karakumica > Penicillinium sp > Calothrix brevissima. The leaching effect of bioaccumulated uranyl ions is higher in hydrochloric acid than in water. (author)

A review of analytical procedures for the simultaneous determination of medically important veterinary antibiotics in environmental water: Sample preparation, liquid chromatography, and mass spectrometry.

Science.gov (United States)

Kim, Chansik; Ryu, Hong-Duck; Chung, Eu Gene; Kim, Yongseok; Lee, Jae-Kwan

2018-07-01

Medically important (MI) antibiotics are defined by the United States Food and Drug Administration as drugs containing certain active antimicrobial ingredients that are used for the treatment of human diseases or enteric pathogens causing food-borne diseases. The presence of MI antibiotic residues in environmental water is a major concern for both aquatic ecosystems and public health, particularly because of their potential to contribute to the development of antimicrobial-resistant microorganisms. In this article, we present a review of global trends in the sales of veterinary MI antibiotics and the analytical methodologies used for the simultaneous determination of antibiotic residues in environmental water. According to recently published government reports, sales volumes have increased steadily, despite many countries having adopted strategies for reducing the consumption of antibiotics. Global attention needs to be directed urgently at establishing new management strategies for reducing the use of MI antimicrobial products in the livestock industry. The development of standardized analytical methods for the detection of multiple residues is required to monitor and understand the fate of antibiotics in the environment. Simultaneous analyses of antibiotics have mostly been conducted using high-performance liquid chromatography-tandem mass spectrometry with a solid-phase extraction (SPE) pretreatment step. Currently, on-line SPE protocols are used for the rapid and sensitive detection of antibiotics in water samples. On-line detection protocols must be established for the monitoring and screening of unknown metabolites and transformation products of antibiotics in environmental water. Copyright © 2018 Elsevier Ltd. All rights reserved.

UMTRA project water sampling and analysis plan, Grand Junction, Colorado

International Nuclear Information System (INIS)

1994-07-01

Surface remedial action will be completed at the Grand Junction processing site during the summer of 1994. Results of 1993 water sampling indicate that ground water flow conditions and ground water quality at the processing site have remained relatively constant with time. Uranium concentrations in ground water continue to exceed the maximum concentration limits, providing the best indication of the extent of contaminated ground water. Evaluation of surface water quality of the Colorado River indicate no impact from uranium processing activities. No compliance monitoring at the Cheney disposal site has been proposed because ground water in the Dakota Sandstone (uppermost aquifer) is classified as limited-use (Class 111) and because the disposal cell is hydrogeologically isolated from the uppermost aquifer. The following water sampling and water level monitoring activities are planned for calendar year 1994: (i) Semiannual (early summer and late fall) sampling of six existing monitor wells at the former Grand Junction processing site. Analytical results from this sampling will be used to continue characterizing hydrogeochemical trends in background ground water quality and in the contaminated ground water area resulting from source term (tailings) removal. (ii) Water level monitoring of approximately three proposed monitor wells projected to be installed in the alluvium at the processing site in September 1994. Data loggers will be installed in these wells, and water levels will be electronically monitored six times a day. These long-term, continuous ground water level data will be collected to better understand the relationship between surface and ground water at the site. Water level and water quality data eventually will be used in future ground water modeling to establish boundary conditions in the vicinity of the Grand Junction processing site. Modeling results will be used to help demonstrate and document the potential remedial alternative of natural flushing

Analysis of glyphosate residues in cereals using liquid chromatography-mass spectrometry (LC-MS/MS)

DEFF Research Database (Denmark)

Granby, Kit; Johannesen, S.; Gabrielsen, Martin Vahl

2003-01-01

A fast and specific method for the determination of glyphosate in cereals is described. The method is based on extraction with water by ultrasonication. The samples are cleaned up and separated by high-performance liquid chromatography on a polystyrene-based reverse-phase column (clean-up) in ser......A fast and specific method for the determination of glyphosate in cereals is described. The method is based on extraction with water by ultrasonication. The samples are cleaned up and separated by high-performance liquid chromatography on a polystyrene-based reverse-phase column (clean...... monitored m/z 168--> 150 (glyphosate) and 170-->152 (internal standard 2- 13 (CN)-N-15-glyphosate) for quantification. The mean recovery was 85% ( n =32) at spiking levels from 0.03 to 0.33 mg kg(-1) . From 1998 to 2001, from the analysis of about 50 samples per annum, a reduction in the glyphosate residues...... was observed owing to a Danish trade decision not to use grain with glyphosate residues for milling or bread production....

Contamination of faecal coliforms in ice cubes sampled from food outlets in Kubang Kerian, Kelantan.

Science.gov (United States)

Noor Izani, N J; Zulaikha, A R; Mohamad Noor, M R; Amri, M A; Mahat, N A

2012-03-01

The use of ice cubes in beverages is common among patrons of food outlets in Malaysia although its safety for human consumption remains unclear. Hence, this study was designed to determine the presence of faecal coliforms and several useful water physicochemical parameters viz. free residual chlorine concentration, turbidity and pH in ice cubes from 30 randomly selected food outlets in Kubang Kerian, Kelantan. Faecal coliforms were found in ice cubes in 16 (53%) food outlets ranging between 1 CFU/100mL to >50 CFU/ 100mL, while in the remaining 14 (47%) food outlets, in samples of tap water as well as in commercially bottled drinking water, faecal coliforms were not detected. The highest faecal coliform counts of >50 CFU/100mL were observed in 3 (10%) food outlets followed by 11-50 CFU/100mL and 1-10 CFU/100mL in 7 (23%) and 6 (20%) food outlets, respectively. All samples recorded low free residual chlorine concentration (contamination by faecal coliforms was not detected in 47% of the samples, tap water and commercially bottled drinking water, it was concluded that (1) contamination by faecal coliforms may occur due to improper handling of ice cubes at the food outlets or (2) they may not be the water sources used for making ice cubes. Since low free residual chlorine concentrations were observed (food outlets, including that of ice cube is crucial in ensuring better food and water for human consumption.

Preparation of stir cake sorptive extraction based on polymeric ionic liquid for the enrichment of benzimidazole anthelmintics in water, honey and milk samples

Energy Technology Data Exchange (ETDEWEB)

Wang, Yulei [State Key Laboratory of Marine Environmental Science, Key Laboratory of the Ministry of Education for Coastal and Wetland Ecosystem, College of the Environment and Ecology, Xiamen University, Siming Road, P.O. Box 1009, Xiamen 361005 (China); Zhang, Jie [Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences (China); Huang, Xiaojia, E-mail: hxj@xmu.edu.cn [State Key Laboratory of Marine Environmental Science, Key Laboratory of the Ministry of Education for Coastal and Wetland Ecosystem, College of the Environment and Ecology, Xiamen University, Siming Road, P.O. Box 1009, Xiamen 361005 (China); Yuan, Dongxing [State Key Laboratory of Marine Environmental Science, Key Laboratory of the Ministry of Education for Coastal and Wetland Ecosystem, College of the Environment and Ecology, Xiamen University, Siming Road, P.O. Box 1009, Xiamen 361005 (China)

2014-08-20

Highlights: • A new polymeric ionic liquid-based monolith was prepared. • The monolith was used as the extractive medium of stir cake sorptive extraction. • The SCSE–AMIIDB can extract benzimidazole anthelmintics (BAs) effectively. • A combination of SCSE–AMIIDB–LD–HPLC/DAD was developed. • The combination was applied to monitor trace BAs in water, milk and honey samples. - Abstract: In this work, a new stir cake sorptive extraction (SCSE) using polymeric ionic liquid monolith as sorbent was prepared. The sorbent was obtained by in situ copolymerization of an ionic liquid, 1-allyl-3-methylimidazolium bis[(trifluoro methyl)sulfonyl]imide (AMII) and divinylbenzene (DB) in the presence of N,N-dimethylformamide. The influence of the content of ionic liquid and the porogen in the polymerization mixture on extraction performance was studied thoroughly. The physicochemical properties of the polymeric ionic liquid were characterized by infrared spectroscopy, elemental analysis, scanning electron microscopy and mercury intrusion porosimetry. The usefulness of SCSE–AMIIDB was demonstrated by the enrichment of trace benzimidazole anthelmintics. Several parameters affecting the extraction efficiency were investigated, and under the optimized conditions, a simple and effective method for the determination of trace benzimidazoles residues in water, milk and honey samples was established by coupling SCSE–AMIIDB with high performance liquid chromatography/diode array detection (SCSE–AMIIDB–HPLC/DAD). Results indicated that the limits of detection (S/N = 3) for target compounds were 0.020–0.072 μg L{sup −1}, 0.035–0.10 μg L{sup −1} and 0.026–0.076 μg L{sup −1} in water, milk and honey samples, respectively. In addition, an acceptable reproducibility was achieved by evaluating the repeatability and intermediate precision with relative standard deviations (RSD) of less than 9% and 11%, respectively. Finally, the established AMII�

Management of NORM Residues

International Nuclear Information System (INIS)

2013-06-01

The IAEA attaches great importance to the dissemination of information that can assist Member States in the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, and that address the legacy of past practices and accidents. However, radioactive residues are found not only in nuclear fuel cycle activities, but also in a range of other industrial activities, including: - Mining and milling of metalliferous and non-metallic ores; - Production of non-nuclear fuels, including coal, oil and gas; - Extraction and purification of water (e.g. in the generation of geothermal energy, as drinking and industrial process water; in paper and pulp manufacturing processes); - Production of industrial minerals, including phosphate, clay and building materials; - Use of radionuclides, such as thorium, for properties other than their radioactivity. Naturally occurring radioactive material (NORM) may lead to exposures at some stage of these processes and in the use or reuse of products, residues or wastes. Several IAEA publications address NORM issues with a special focus on some of the more relevant industrial operations. This publication attempts to provide guidance on managing residues arising from different NORM type industries, and on pertinent residue management strategies and technologies, to help Member States gain perspectives on the management of NORM residues

Residual monomer content determination in some acrylic denture base materials and possibilities of its reduction

Directory of Open Access Journals (Sweden)

Kostić Milena

2009-01-01

Full Text Available Background/Aim. Polymethyl methacrylate is used for producing a denture basis. It is a material made by the polymerization process of methyl methacrylate. Despite of the polymerization type, there is a certain amount of free methyl methacrylate (residual monomer incorporated in the denture, which can cause irritation of the oral mucosa. The aim of this study was to determine the amount of residual monomer in four different denture base acrylic resins by liquid chromatography and the possibility of its reduction. Methods. After the polymerization, a postpolymerization treatment was performed in three different ways: in boiling water for thirty minutes, with 500 W microwaves for three minutes and in steam bath at 22º C for one to thirty days. Results. The obtained results showed that the amount of residual monomer is significantly higher in cold polymerizing acrylates (9.1-11%. The amount of residual monomer after hot polymerization was in the tolerance range (0.59- 0.86%. Conclusion. The obtained results denote a low content of residual monomer in the samples which have undergone postpolymerization treatment. A lower percent of residual monomer is established in samples undergone a hot polymerization.

Investigation on reusing water treatment residuals to remedy soil contaminated with multiple metals in Baiyin, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Changhui; Zhao, Yuanyuan [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China); Pei, Yuansheng, E-mail: yspei@bnu.edu.cn [The Key Laboratory of Water and Sediment Sciences, Ministry of Education, School of Environment, Beijing Normal University, Beijing 100875 (China)

2012-10-30

Highlights: Black-Right-Pointing-Pointer Fe/Al water treatment residuals (FARs) can stabilize As, Pb, Ni, Zn, Cr and Cu. Black-Right-Pointing-Pointer FARs cannot stabilize Ba and Cd. Black-Right-Pointing-Pointer The properties of FARs and soil affect the FARs' ability of stabilizing metals. - Abstract: In this work, the remediation of soils contaminated with multiple metals using ferric and alum water treatment residuals (FARs) in Baiyin, China, was investigated. The results of metals fractionation indicated that after the soil was treated with FARs, arsenic (As), lead (Pb), nickel (Ni), zinc (Zn) and copper (Cu) could be transformed into more stable forms, i.e., As bound in crystalline Fe/Al oxides and other metals in the oxidable and residual forms. However, the forms of chromium (Cr) and cadmium (Cd) were unaffected. Interestingly, due to the effect of FARs, barium (Ba) was predominantly transformed into more mobile forms. The bioaccessibility extraction test demonstrated that the FARs reduced the bioaccessibility of As by 25%, followed by Cu, Cr, Zn, Ni and Pb. The bioaccessibility of Cd and Ba were increased; in particular, there was an increase of 41% for Ba at the end of the test. In conclusion, the FARs can be used to remedy soil contaminated with multiple metals, but comprehensive studies are needed before practical applications of this work.

Depletion of eugenol residues from the skin-on fillet tissue of rainbow trout exposed to 14C-labeled eugenol

Science.gov (United States)

Meinertz, Jeffery R.; Schreier, Theresa M.; Porcher, Scott T.; Smerud, Justin R.; Gaikowski, Mark P.

2014-01-01

The U.S. is lagging in access to an approved immediate-release sedative, i.e. a compound that can be safely and effectively used to sedate fish and has no withdrawal period. AQUI-S® 20E (10% active ingredient, eugenol) is under investigation as an immediate-release sedative for freshwater finfish. Because of its investigational status, data are needed to characterize the depletion, distribution, and identity of AQUI-S® 20E residues in fillet tissue. Rainbow trout (Oncorhynchus mykiss) were exposed to uniformly ring labeled 14C-eugenol at a nominal concentration of 10 mg/L for 60 min in 18 °C water. Fish (n = 6) were sampled immediately after the exposure (0 min) then at 30, 60, 120, and 240 min. Eugenol concentrations and characterization of 14C residues in the fillet tissue were determined by high pressure liquid chromatography and flow-through liquid scintillation counting techniques. Total 14C-residue burdens in fillet tissue were determined by tissue oxidation and static liquid scintillation counting techniques. Maximum eugenol and 14C-eugenol equivalent residue concentrations in the fillet tissue were measured immediately after the exposure (44.5 and 38.8 μg/g, respectively). Eugenol was the primary 14C-residue (> 90% of all 14C-residues) in extracts from fillet tissue taken from fish sampled immediately after the exposure (0 min) and from fish sampled at 30 and 60 min after the exposure. The depletion of 14C-eugenol residues from the fillet tissue was rapid (t1/2 = 26.25 min) after transferring the exposed fish to fresh flowing water.

Detection of clarithromycin-resistant Helicobacter pylori by polymerase chain reaction using residual samples from rapid urease test

Directory of Open Access Journals (Sweden)

Jae-Sik Jeon

2017-01-01

Full Text Available Background: Approximately 50% of the world population is infected with Helicobacter pylori, which corresponds to a high infection rate. Furthermore, the incidence of antibiotic-resistant H. pylori has increased with the recent rise in use of antibiotics for H. pylori elimination, suggesting growing treatment failures. Aim: The study was aimed to assess the use of residual samples from rapid urease test (RUT for biomolecular testing as an effective and accurate method to detect antibiotic-resistant H. pylori. Settings and Design: This study was a retrospective study performed using data obtained from medical records of previously isolated H. pylori strains. Materials and Methods: RUT was conducted for 5440 biopsy samples from individuals who underwent health examination in South Korea. Subsequently, 469 RUT residual samples were randomly selected and subjected to polymerase chain reaction (PCR to detect antibiotic-resistant H. pylori. Statistical Analysis Used: The Chi-square test was used to analyse categorical data. P < 0.05 was considered statistically significant. Results: The results showed a concordance between the results of PCR and conventional RUT in 450 of 469 samples, suggesting that the H. pylori PCR test is a time- and cost-effective detection method. Conclusions: This study demonstrated that PCR test can aid physicians to prescribe the appropriate antibiotics at the time of diagnosis, thus preventing the reduction in H. pylori eradication due to antibiotic resistance, averting progression to serious diseases and increasing the treatment success rate.

Aluminum drinking water treatment residuals (Al-WTRs) as sorbent for mercury: Implications for soil remediation.

Science.gov (United States)

Hovsepyan, Anna; Bonzongo, Jean-Claude J

2009-05-15

The potential of readily available and non-hazardous waste material, aluminum drinking water treatment residuals (Al-WTRs), to efficiently sorb and immobilize mercury (Hg) from aqueous solutions was evaluated. Al-WTR samples with average specific surface area of 48m(2)/g and internal micropore surface area of 120m(2)/g were used in a series of batch sorption experiments. Obtained sorption isotherms indicated a strong affinity of Hg for Al-WTRs. Using the Langmuir adsorption model, a relatively high maximum sorption capacity of 79mg Hg/g Al-WTRs was determined. Sorption kinetic data was best fit to a pseudo-first-order model, while the use of the Weber-Morris and Bangham models suggested that the intraparticle diffusion could be the rate-limiting step. Also, Al-WTRs effectively immoblized Hg in the pH range of 3-8. The results from these short-term experiments demonstrate that Al-WTRs can be effectively used to remove Hg from aqueous solutions. This ability points to the potential of Al-WTRs as a sorbent in soil remediation techniques based on Hg-immobilization.

Removal of emulsified oil in residual waters by means of dissolved air flotation

International Nuclear Information System (INIS)

Echeverri Londono, Carlos Alberto

1996-01-01

In this article is consigned a theoretical and experimental study on the treatment of industrial residual waters with emulsified oil, through the flotation process for dissolved air (FAD), changing some operation parameters and some importance topics, related with the process. The experimental results and the theoretical pattern, show that the removal of oil depends fundamentally on the chemical pretreatment. Efficiencies of removal of oil up of 99% they were obtained, using the dissolved air flotation with the help of coagulants

Effect of an absorbent overlay on the residual stress field induced by laser shock processing on aluminum samples

International Nuclear Information System (INIS)

Rubio-Gonzalez, C.; Gomez-Rosas, G.; Ocana, J.L.; Molpeceres, C.; Banderas, A.; Porro, J.; Morales, M.

2006-01-01

Laser shock processing (LSP) or laser shock peening is a new technique for strengthening metals. This process induces a compressive residual stress field, which increases fatigue crack initiation life and reduces fatigue crack growth rate. Specimens of 6061-T6 aluminum alloy are used in this investigation. A convergent lens is used to deliver 2.5 J, 8 ns laser pulses by a Q-switch Nd:YAG laser, operating at 10 Hz. The pulses are focused to a diameter of 1.5 mm onto aluminum samples. Density of 2500 pulses/cm 2 with infrared (1064 nm) radiation was used. The effect of an absorbent overlay on the residual stress field using this LSP setup and this energy level is evaluated. Residual stress distribution as a function of depth is assessed by the hole drilling method. It is observed that the overlay makes the compressive residual stress profile move to the surface. This effect is explained on the basis of the vaporization of the coat layer suppressing thermal effects on the metallic substrate. The effect of coating the specimen surface before LSP treatment may have advantages on improving wear and contact fatigue properties of this aluminum alloy

Polder Effects on Sediment-to-Soil Conversion: Water Table, Residual Available Water Capacity, and Salt Stress Interdependence

Directory of Open Access Journals (Sweden)

Raymond Tojo Radimy

2013-01-01

Full Text Available The French Atlantic marshlands, reclaimed since the Middle Age, have been successively used for extensive grazing and more recently for cereal cultivation from 1970. The soils have acquired specific properties which have been induced by the successive reclaiming and drainage works and by the response of the clay dominant primary sediments, that is, structure, moisture, and salinity profiles. Based on the whole survey of the Marais Poitevin and Marais de Rochefort and in order to explain the mechanisms of marsh soil behavior, the work focuses on two typical spots: an undrained grassland since at least 1964 and a drained cereal cultivated field. The structure-hydromechanical profiles relationships have been established thanks to the clay matrix shrinkage curve. They are confronted to the hydraulic functioning including the fresh-to-salt water transfers and to the recording of tensiometer profiles. The CE1/5 profiles supply the water geochemical and geophysical data by their better accuracy. Associated to the available water capacity calculation they allow the representation of the parallel evolution of the residual available water capacity profiles and salinity profiles according to the plant growing and rooting from the mesophile systems of grassland to the hygrophile systems of drained fields.

Solid residues

International Nuclear Information System (INIS)

Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

1995-01-01

A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

Isolation of viruses from drinking water at the Point-Viau water treatment plant

Energy Technology Data Exchange (ETDEWEB)

Payment, P.

1981-04-01

Viruses were isolated from every sample of raw (100 L) and treated (1000 L) water collected at a water treatment plant drawing sewage-contaminated river water. Few plaque-forming isolates were formed but cytopathogenic viruses were isolated as frequently in drinking water as in raw water. In drinking water some samples contained more than 1 cytopathogenic unit per litre, but most contained 1-10/100 L. These viruses had not been inactivated or removed by prechlorination, flocculation, filtration, ozonation, and postchlorination. There were no coliforms present and a residual chlorine level had been maintained. Poliovirus type 1 was a frequent isolate but many isolates were nonpoliovirus. The presence of these viruses in drinking water raises questions about the efficacy of some water treatment processes to remove viruses from polluted water.

Effect of cooking on enrofloxacin residues in chicken tissue.

Science.gov (United States)

Lolo, M; Pedreira, S; Miranda, J M; Vázquez, B I; Franco, C M; Cepeda, A; Fente, C

2006-10-01

The aim of this study was to determine the effect of different cooking processes (microwaving, roasting, boiling, grilling and frying) on naturally incurred enrofloxacin residues in chicken muscle. Enrofloxacin and its metabolite, ciprofloxacin, were analysed using a validated LC-MS method with limits of detection (LOD) and quantification (LOQ), respectively, of 2 and 5 ng g-1 quinolones in muscle samples. The method was shown to be linear over the range 5-500 ng g-1. Mean intra-day relative standard deviation (RSD) at a concentration of 50 ng g-1 (n = 6) was 6%; inter-day RSD was 12%. A recovery study demonstrated that 65-101%, of the drug and metabolite could be recovered from the tissue. The RSD with naturally incurred roasted chicken breast was 9.18% at a concentration of 11 +/- 1.01 ng g-1 (n = 6). In water, enrofloxacin remained stable for 3 h when heated at 100 degrees C. It was concluded that residue data from raw tissue are valid for estimation of consumer exposure to this drug, as well as the ADI calculations because cooking procedures did not affect enrofloxacin residues, which remained stable during heating. However, there was an apparent decrease in quinolone concentration in tissue because some was lost by exudation into the liquid used for cooking. Conversely, for a cooking procedure with water loss, there was an apparent increase in residue concentration.

An Assessment of Factors Having Impact on Water Quality in Water Supply Pipelines

Directory of Open Access Journals (Sweden)

Auksė Amosenkienė

2011-04-01

Full Text Available Water samples were collected from Vilnius drinking water distribution system fed by treated and different groundwater. Parameters related to bacterial growth have been measured considering these samples: temperature, concentration of free residual chlorine, ammonium, nitrates and nitrites. Results showed that treated groundwater was less susceptible to favour bacterial growth in the pipelines. The obtained results also showed that the potential growth induced by the distribution of treated water could be reduced if: ammonium levels were below 0.5 mg/l at the outlet of the water treatment plant; biological ammonium removal treatment implementation should reduce the levels of the nitrates and nitrites of the treated supplied water. Article in Lithuanian

UMTRA project water sampling and analysis plan, Mexican Hat, Utah

International Nuclear Information System (INIS)

1994-04-01

The Mexican Hat, Utah, Uranium Mill Tailings Remedial Action (UMTRA) Project site is a former uranium mill that is undergoing surface remediation in the form of on-site tailings stabilization. Contaminated surface materials from the Monument Valley, Arizona, UMTRA Project site have been transported to the Mexican Hat site and are being consolidated with the Mexican Hat tailings. The scheduled completion of the tailings disposal cell is August 1995. Water is found in two geologic units at the site: the Halgaito Shale Formation and the Honaker Trail Formation. The tailings rest on the Halgaito Shale, and water contained in that unit is a result of milling activities and, to a lesser extent, water released from the tailings from compaction during remedial action construction of the disposal cell. Water in the Halgaito Shale flows through fractures and discharges at seeps along nearby arroyos. Flow from the seeps will diminish as water drains from the unit. Ground water in the lower unit, the Honaker Trail Formation, is protected from contamination by an upward hydraulic gradient. There are no nearby water supply wells because of widespread poor background ground water quality and quantity, and the San Juan River shows no impacts from the site. This water sampling and analysis plan (WSAP) recommends sampling six seeps and one upgradient monitor well compared in the Honaker Trail Formation. Samples will be taken in April 1994 (representative of high group water levels) and September 1994 (representative of low ground water levels). Analyses will be performed on filtered samples for plume indicator parameters

Uranium content measurement in drinking water samples using track etch technique

International Nuclear Information System (INIS)

Kumar, Mukesh; Kumar, Ajay; Singh, Surinder; Mahajan, R.K.; Walia, T.P.S.

2003-01-01

The concentration of uranium has been assessed in drinking water samples collected from different locations in Bathinda district, Punjab, India. The water samples are taken from hand pumps and tube wells. Uranium is determined using fission track technique. Uranium concentration in the water samples varies from 1.65±0.06 to 74.98±0.38 μg/l. These values are compared with safe limit values recommended for drinking water. Most of the water samples are found to have uranium concentration above the safe limit. Analysis of some heavy metals (Zn, Cd, Pb and Cu) in water is also done in order to see if some correlation exists between the concentration of uranium and these heavy metals. A weak positive correlation has been observed between the concentration of uranium and heavy metals of Pb, Cd and Cu

A Study on the Residual Stress Improvement of PWSCC(Primary Water Stress Corrosion Cracking) in DMW(Dissimilar Metal Weld)

International Nuclear Information System (INIS)

Kang, Sung Sik; Kim, Seok Hun; Lee, Seung Gun; Park, Heung Bae

2010-01-01

Since 2000s, most of the cracks are found in welds, especially in (DMW) dissimilar metal welds such as pressurizer safety relief nozzle, reactor head penetration, reactor bottom mounted instrumentation (BMI), and reactor nozzles. Even the cracks are revealed as a primary water stress corrosion cracking (PWSCC), it is difficult to find the cracks by current non destructive examination. The PWSCC is occurred by three incident factors, such as susceptible material, environmental corrosive condition, and welding residual stress. If one of the three factors can be erased or decreased, the PWSCC could be prevented. In this study, we performed residual stress analysis for DMW and several residual stress improvement methods. As the preventive methods of PWSCC, we used laser peening(IP) method, inlay weld(IW) method, and induction heating stress improvement(IHSI) method. The effect of residual stress improvement for preventive methods was compared and discussed by finite element modeling and residual stress of repaired DMW

Development of an enzyme-linked immunosorbent assay for seven sulfonamide residues and investigation of matrix effects from different food samples.

Science.gov (United States)

Zhang, Hongyan; Wang, Lei; Zhang, Yan; Fang, Guozhen; Zheng, Wenjie; Wang, Shuo

2007-03-21

Direct competitive enzyme-linked immunosorbent assays (ELISA) were developed to detect a broad range of sulfonamides in various matrices. Screening for this class of antibiotics in pig muscle, chicken muscle, fish, and egg extracts was accomplished by simple, rapid extraction methods carried out with only phosphate-buffered saline (PBS) buffer. Twenty milliliters of extract solution was added to 4 g of sample to extract the sulfonamide residues, and sample extracts diluted with assay buffer were directly analyzed by ELISA; matrix effects could be avoided with 1:5 dilution of pig muscle, chicken muscle, and egg extracts with PBS and 1:5 dilution of fish extract with 1% bovine serum albumin (BSA)-PBS. For liver sample, the extraction method was a little more complicated; 2 g of sample was added to 20 mL of ethanol, mixed, and then centrifuged. The solvent of 10 mL of the upper liquid was removed, and the residues were dissolved in 10 mL of PBS and then filtered; the filtrate was diluted two-fold with 0.5% BSA-PBS for ELISA. These common methods were able to detect seven sulfonamide residues such as sulfisozole, sulfathiazole, sufameter, sulfamethoxypyridazine, sulfapyridine, sulfamethizole, and sulfachlorpyridazine in pig muscle, liver, chicken muscle, egg, and fish. The assay's detection limits for these compounds were less than 100 microg kg-1. Various extraction methods were tested, and the average recovery (n=3) of 100 microg kg-1 for the matrices was found to range from 77.3 to 123.7%.

Residual stress improving method for reactor structural component and residual stress improving device therefor

Energy Technology Data Exchange (ETDEWEB)

Enomoto, Kunio; Otaka, Masahiro; Kurosawa, Koichi; Saito, Hideyo; Tsujimura, Hiroshi; Tamai, Yasukata; Urashiro, Keiichi; Mochizuki, Masato

1996-09-03

The present invention is applied to a BWR type reactor, in which a high speed jetting flow incorporating cavities is collided against the surface of reactor structural components to form residual compression stresses on the surface layer of the reactor structural components thereby improving the stresses on the surface. Namely, a water jetting means is inserted into the reactor container filled with reactor water. Purified water is pressurized by a pump and introduced to the water jetting means. The purified water jetted from the water jetting means and entraining cavities is abutted against the surface of the reactor structural components. With such procedures, since the purified water is introduced to the water jetting means by the pump, the pump is free from contamination of radioactive materials. As a result, maintenance and inspection for the pump can be facilitated. Further, since the purified water injection flow entraining cavities is abutted against the surface of the reactor structural components being in contact with reactor water, residual compression stresses are exerted on the surface of the reactor structural components. As a result, occurrence of stress corrosion crackings of reactor structural components is suppressed. (I.S.)

Residual stress improving method for reactor structural component and residual stress improving device therefor

International Nuclear Information System (INIS)

Enomoto, Kunio; Otaka, Masahiro; Kurosawa, Koichi; Saito, Hideyo; Tsujimura, Hiroshi; Tamai, Yasukata; Urashiro, Keiichi; Mochizuki, Masato.

1996-01-01

The present invention is applied to a BWR type reactor, in which a high speed jetting flow incorporating cavities is collided against the surface of reactor structural components to form residual compression stresses on the surface layer of the reactor structural components thereby improving the stresses on the surface. Namely, a water jetting means is inserted into the reactor container filled with reactor water. Purified water is pressurized by a pump and introduced to the water jetting means. The purified water jetted from the water jetting means and entraining cavities is abutted against the surface of the reactor structural components. With such procedures, since the purified water is introduced to the water jetting means by the pump, the pump is free from contamination of radioactive materials. As a result, maintenance and inspection for the pump can be facilitated. Further, since the purified water injection flow entraining cavities is abutted against the surface of the reactor structural components being in contact with reactor water, residual compression stresses are exerted on the surface of the reactor structural components. As a result, occurrence of stress corrosion crackings of reactor structural components is suppressed. (I.S.)

Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals

Energy Technology Data Exchange (ETDEWEB)

Deliz Quiñones, Katherine, E-mail: Katherine.Deliz@amecfw.com; Hovsepyan, Anna, E-mail: anna_Hovsepyan@urscorp.com; Oppong-Anane, Akua; Bonzongo, Jean-Claude J., E-mail: bonzongo@ufl.edu

2016-04-15

Highlights: • Mercury sorption by Al-WTRs involves electrostatic forces and chemisorption. • Hg forms bonds with oxygen and sulfur atoms of Al-WTR’s organic ligands. • Mercury is incorporated into the residual fraction to form stable complexes. • Mercury binds mainly to SiO{sub x} species in the residual fraction. - Abstract: Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal–WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding.

Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals

International Nuclear Information System (INIS)

Deliz Quiñones, Katherine; Hovsepyan, Anna; Oppong-Anane, Akua; Bonzongo, Jean-Claude J.

2016-01-01

Highlights: • Mercury sorption by Al-WTRs involves electrostatic forces and chemisorption. • Hg forms bonds with oxygen and sulfur atoms of Al-WTR’s organic ligands. • Mercury is incorporated into the residual fraction to form stable complexes. • Mercury binds mainly to SiO x species in the residual fraction. - Abstract: Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal–WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding.

Alternatives to crop residues for soil amendment

OpenAIRE

Powell, J.M.; Unger, P.W.

1997-01-01

Metadata only record In semiarid agroecosystems, crop residues can provide important benefits of soil and water conservation, nutrient cycling, and improved subsequent crop yields. However, there are frequently multiple competing uses for residues, including animal forage, fuel, and construction material. This chapter discusses the various uses of crop residues and examines alternative soil amendments when crop residues cannot be left on the soil.

Determination of Phenols in Water Samples using a Supported ...

African Journals Online (AJOL)

The sample preparation method was tested for the determination of phenols in river water samples and landfill leachate. Concentrations of phenols in river water were found to be in the range 4.2 μg L–1 for 2-chlorophenol to 50 μg L–1 for 4-chlorophenol. In landfill leachate, 4-chlorophenol was detected at a concentration ...

UMTRA Project water sampling and analysis plan, Durango, Colorado. Revision 1

International Nuclear Information System (INIS)

1995-09-01

Planned, routine ground water sampling activities at the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site in Durango, Colorado, are described in this water sampling and analysis plan. The plan identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the routine monitoring stations at the site. The ground water data are used to characterize the site ground water compliance strategies and to monitor contaminants of potential concern identified in the baseline risk assessment (DOE, 1995a). Regulatory basis for routine ground water monitoring at UMTRA Project sites is derived from the US EPA regulations in 40 CFR Part 192 (1994) and EPA standards of 1995 (60 FR 2854). Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), the Technical Approach Document (TAD) (DOE, 1989), and the most effective technical approach for the site

chemical and microbiological assessment of surface water samples

African Journals Online (AJOL)

PROF EKWUEME

were investigated in this study: Nine samples from different surface water bodies, two samples from two effluent sources ... Ezeagu, Udi, Nkanu, Oji River and some parts of Awgu and Aninri ..... Study of Stream Output from Small Catchments.