Improving recovery efficiency of water-drive channel sandstone reservoir by drilling wells laterally

Energy Technology Data Exchange (ETDEWEB)

Zhiguo, F.; Quinglong, D.; Pingshi, Z.; Bingyu, J.; Weigang, L. [Research Institute of Exploration and Development, Daqing (China)

1998-12-31

Example of drilling a horizontal well in reservoir rock of only four meter thick by using existing casing pipe of low efficiency vertical wells to induce production in the top remaining reservoir is described. The experience shows that drilling horizontal wells laterally in thin bodies of sandstone reservoirs and improve their productivity is a feasible proposition. Productivity will still be low, but it can be improved by well stimulation. 3 refs., 3 figs.

Prediction of calcite Cement Distribution in Shallow Marine Sandstone Reservoirs using Seismic Data

Energy Technology Data Exchange (ETDEWEB)

Bakke, N.E.

1996-12-31

This doctoral thesis investigates how calcite cemented layers can be detected by reflection seismic data and how seismic data combined with other methods can be used to predict lateral variation in calcite cementation in shallow marine sandstone reservoirs. Focus is on the geophysical aspects. Sequence stratigraphy and stochastic modelling aspects are only covered superficially. Possible sources of calcite in shallow marine sandstone are grouped into internal and external sources depending on their location relative to the presently cemented rock. Well data and seismic data from the Troll Field in the Norwegian North Sea have been analysed. Tuning amplitudes from stacks of thin calcite cemented layers are analysed. Tuning effects are constructive or destructive interference of pulses resulting from two or more closely spaced reflectors. The zero-offset tuning amplitude is shown to depend on calcite content in the stack and vertical stack size. The relationship is found by regression analysis based on extensive seismic modelling. The results are used to predict calcite distribution in a synthetic and a real data example. It is found that describing calcite cemented beds in shallow marine sandstone reservoirs is not a deterministic problem. Hence seismic inversion and sequence stratigraphy interpretation of well data have been combined in a probabilistic approach to produce models of calcite cemented barriers constrained by a maximum amount of information. It is concluded that seismic data can provide valuable information on distribution of calcite cemented beds in reservoirs where the background sandstones are relatively homogeneous. 63 refs., 78 figs., 10 tabs.

Characterization and 3D reservoir modelling of fluvial sandstones of the Williams Fork Formation, Rulison Field, Piceance Basin, Colorado, USA

International Nuclear Information System (INIS)

Pranter, Matthew J; Vargas, Marielis F; Davis, Thomas L

2008-01-01

This study describes the stratigraphic characteristics and distribution of fluvial deposits of the Upper Cretaceous Williams Fork Formation in a portion of Rulison Field and addresses 3D geologic modelling of reservoir sand bodies and their associated connectivity. Fluvial deposits include isolated and stacked point-bar deposits, crevasse splays and overbank (floodplain) mudrock. Within the Williams Fork Formation, the distribution and connectivity of fluvial sandstones significantly impact reservoir productivity and ultimate recovery. The reservoir sandstones are primarily fluvial point-bar deposits interbedded with shales and coals. Because of the lenticular geometry and limited lateral extent of the reservoir sandstones (common apparent widths of ∼500–1000 ft; ∼150–300 m), relatively high well densities (e.g. 10 acre (660 ft; 200 m) spacing) are often required to deplete the reservoir. Heterogeneity of these fluvial deposits includes larger scale stratigraphic variability associated with vertical stacking patterns and structural heterogeneities associated with faults that exhibit lateral and reverse offsets. The discontinuous character of the fluvial sandstones and lack of distinct marker beds in the middle and upper parts of the Williams Fork Formation make correlation between wells tenuous, even at a 10 acre well spacing. Some intervals of thicker and amalgamated sandstones within the middle and upper Williams Fork Formation can be correlated across greater distances. To aid correlation and for 3D reservoir modelling, vertical lithology proportion curves were used to estimate stratigraphic trends and define the stratigraphic zonation within the reservoir interval. Object-based and indicator-based modelling methods have been applied to the same data and results from the models were compared. Results from the 3D modelling indicate that sandstone connectivity increases with net-to-gross ratio and, at lower net-to-gross ratios (<30%), differences exist in

Hydrocarbon Potential in Sandstone Reservoir Isolated inside Low Permeability Shale Rock (Case Study: Beruk Field, Central Sumatra Basin)

Science.gov (United States)

Diria, Shidqi A.; Musu, Junita T.; Hasan, Meutia F.; Permono, Widyo; Anwari, Jakson; Purba, Humbang; Rahmi, Shafa; Sadjati, Ory; Sopandi, Iyep; Ruzi, Fadli

2018-03-01

Upper Red Bed, Menggala Formation, Bangko Formation, Bekasap Formation and Duri Formationare considered as the major reservoirs in Central Sumatra Basin (CSB). However, Telisa Formation which is well-known as seal within CSB also has potential as reservoir rock. Field study discovered that lenses and layers which has low to high permeability sandstone enclosed inside low permeability shale of Telisa Formation. This matter is very distinctive and giving a new perspective and information related to the invention of hydrocarbon potential in reservoir sandstone that isolated inside low permeability shale. This study has been conducted by integrating seismic data, well logs, and petrophysical data throughly. Facies and static model are constructed to estimate hydrocarbon potential resource. Facies model shows that Telisa Formation was deposited in deltaic system while the potential reservoir was deposited in distributary mouth bar sandstone but would be discontinued bedding among shale mud-flat. Besides, well log data shows crossover between RHOB and NPHI, indicated that distributary mouth bar sandstone is potentially saturated by hydrocarbon. Target area has permeability ranging from 0.01-1000 mD, whereas porosity varies from 1-30% and water saturation varies from 30-70%. The hydrocarbon resource calculation approximates 36.723 MSTB.

Reservoir Characterization of Bridgeport and Cypress Sandstones in Lawrence Field Illinois to Improve Petroleum Recovery by Alkaline-Surfactant-Polymer Flood

Energy Technology Data Exchange (ETDEWEB)

Seyler, Beverly; Grube, John; Huff, Bryan; Webb, Nathan; Damico, James; Blakley, Curt; Madhavan, Vineeth; Johanek, Philip; Frailey, Scott

2012-12-21

were used to better understand porosity and permeability trends in the region and to characterize barriers and define flow units. Diagenetic alterations that impact porosity and permeability include development of quartz overgrowths, sutured quartz grains, dissolution of feldspar grains, formation of clay mineral coatings on grains, and calcite cementation. Many of these alterations are controlled by facies. Mapping efforts identified distinct flow units in the northern part of the field showing that the Pennsylvanian Bridgeport consists of a series of thick incised channel fill sequences. The sandstones are about 75-150 feet thick and typically consist of medium grained and poorly sorted fluvial to distributary channel fill deposits at the base. The sandstones become indistinctly bedded distributary channel deposits in the main part of the reservoir before fining upwards and becoming more tidally influenced near their top. These channel deposits have core permeabilities ranging from 20 md to well over 1000 md. The tidally influenced deposits are more compartmentalized compared to the thicker and more continuous basal fluvial deposits. Fine grained sandstones that are laterally equivalent to the thicker channel type deposits have permeabilities rarely reaching above 250 md. Most of the unrecovered oil in Lawrence Field is contained in Pennsylvanian Age Bridgeport sandstones and Mississippian Age Cypress sandstones. These reservoirs are highly complex and compartmentalized. Detailed reservoir characterization including the development of 3-D geologic and geocellular models of target areas in the field were completed to identify areas with the best potential to recover remaining reserves including unswept and by-passed oil. This project consisted of tasks designed to compile, interpret, and analyze the data required to conduct reservoir characterization for the Bridgeport and Cypress sandstones in pilot areas in anticipation of expanded implementation of ASP flooding in

STRUCTURAL HETEROGENEITIES AND PALEO FLUID FLOW IN AN ANALOG SANDSTONE RESERVOIR 2001-2004

International Nuclear Information System (INIS)

Pollard, David; Aydin, Atilla

2005-01-01

Fractures and faults are brittle structural heterogeneities that can act both as conduits and barriers with respect to fluid flow in rock. This range in the hydraulic effects of fractures and faults greatly complicates the challenges faced by geoscientists working on important problems: from groundwater aquifer and hydrocarbon reservoir management, to subsurface contaminant fate and transport, to underground nuclear waste isolation, to the subsurface sequestration of CO2 produced during fossil-fuel combustion. The research performed under DOE grant DE-FG03-94ER14462 aimed to address these challenges by laying a solid foundation, based on detailed geological mapping, laboratory experiments, and physical process modeling, on which to build our interpretive and predictive capabilities regarding the structure, patterns, and fluid flow properties of fractures and faults in sandstone reservoirs. The material in this final technical report focuses on the period of the investigation from July 1, 2001 to October 31, 2004. The Aztec Sandstone at the Valley of Fire, Nevada, provides an unusually rich natural laboratory in which exposures of joints, shear deformation bands, compaction bands and faults at scales ranging from centimeters to kilometers can be studied in an analog for sandstone aquifers and reservoirs. The suite of structures there has been documented and studied in detail using a combination of low-altitude aerial photography, outcrop-scale mapping and advanced computational analysis. In addition, chemical alteration patterns indicative of multiple paleo fluid flow events have been mapped at outcrop, local and regional scales. The Valley of Fire region has experienced multiple episodes of fluid flow and this is readily evident in the vibrant patterns of chemical alteration from which the Valley of Fire derives its name. We have successfully integrated detailed field and petrographic observation and analysis, process-based mechanical modeling, and numerical

ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

International Nuclear Information System (INIS)

Jennie Ridgley

2000-01-01

A goal of the Mesaverde project was to better define the depositional system of the Mesaverde in hopes that it would provide insight to new or by-passed targets for oil exploration. The new, detailed studies of the Mesaverde give us a better understanding of the lateral variability in depositional environments and facies. Recognition of this lateral variability and establishment of the criteria for separating deltaic, strandplain-barrier, and estuarine deposits from each other permit development of better hydrocarbon exploration models, because the sandstone geometry differs in each depositional system. Although these insights will provide better exploration models for gas exploration, it does not appear that they will be instrumental in finding more oil. Oil in the Mesaverde Group is produced from isolated fields on the Chaco slope; only a few wells define each field. Production is from sandstone beds in the upper part of the Point Lookout Sandstone or from individual fluvial channel sandstones in the Menefee. Stratigraphic traps rather than structural traps are more important. Source of the oil in the Menefee and Point Lookout may be from interbedded organic-rich mudstones or coals rather than from the Lewis Shale. The Lewis Shale appears to contain more type III organic matter and, hence, should produce mainly gas. Outcrop studies have not documented oil staining that might point to past oil migration through the sandstones of the Mesaverde. The lack of oil production may be related to the following: (1) lack of abundant organic matter of the type I or II variety in the Lewis Shale needed to produce oil, (2) ineffective migration pathways due to discontinuities in sandstone reservoir geometries, (3) cementation or early formation of gas prior to oil generation that reduced effective permeabilities and served as barriers to updip migration of oil, or (4) erosion of oilbearing reservoirs from the southern part of the basin. Any new production should mimic that of

Electrofacies vs. lithofacies sandstone reservoir characterization Campanian sequence, Arshad gas/oil field, Central Sirt Basin, Libya

Science.gov (United States)

Burki, Milad; Darwish, Mohamed

2017-06-01

The present study focuses on the vertically stacked sandstones of the Arshad Sandstone in Arshad gas/oil field, Central Sirt Basin, Libya, and is based on the conventional cores analysis and wireline log interpretation. Six lithofacies types (F1 to F6) were identified based on the lithology, sedimentary structures and biogenic features, and are supported by wireline log calibration. From which four types (F1-F4) represent the main Campanian sandstone reservoirs in the Arshad gas/oil field. Lithofacies F5 is the basal conglomerates at the lower part of the Arshad sandstones. The Paleozoic Gargaf Formation is represented by lithofacies F6 which is the source provenance for the above lithofacies types. Arshad sediments are interpreted to be deposited in shallow marginal and nearshore marine environment influenced by waves and storms representing interactive shelf to fluvio-marine conditions. The main seal rocks are the Campanian Sirte shale deposited in a major flooding events during sea level rise. It is contended that the syn-depositional tectonics controlled the distribution of the reservoir facies in time and space. In addition, the post-depositional changes controlled the reservoir quality and performance. Petrophysical interpretation from the porosity log values were confirmed by the conventional core measurements of the different sandstone lithofacies types. Porosity ranges from 5 to 20% and permeability is between 0 and 20 mD. Petrophysical cut-off summary of the lower part of the clastic dominated sequence (i. e. Arshad Sandstone) calculated from six wells includes net pay sand ranging from 19.5‧ to 202.05‧, average porosity from 7.7 to 15% and water saturation from 19 to 58%.

The effects of impure CO2 on reservoir sandstones: results from mineralogical and geomechanical experiments

Science.gov (United States)

Marbler, H.; Erickson, K. P.; Schmidt, M.; Lempp, Ch.; Pöllmann, H.

2012-04-01

An experimental study of the behaviour of reservoir sandstones from deep saline aquifers during the injection and geological storage of CO2 with the inherent impurities SOX and NOX is part of the German national project COORAL*. Sample materials were taken from outcrops of possible reservoir formations of Rotliegend and Bunter Sandstones from the North German Basin. A combination of mineralogical alteration experiments and geomechanical tests was carried out on these rocks to study the potential effects of the impurities within the CO2 pore fluid. Altered rock samples after the treatment with CO2 + SOX/NOX in an autoclave system were loaded in a triaxial cell under in-situ pressure and temperature conditions in order to estimate the modifications of the geomechanical rock properties. Mineralogical alterations were observed within the sandstones after the exposure to impure supercritical (sc)CO2 and brine, mainly of the carbonatic, but also of the silicatic cements, as well as of single minerals. Besides the partial solution effects also secondary carbonate and minor silicate mineral precipitates were observed within the pore space of the treated sandstones. These alterations affect the grain structure of the reservoir rock. Results of geomechanical experiments with unaltered sandstones show that the rock strength is influenced by the degree of rock saturation before the experiment and the chemical composition of the pore fluid (scCO2 + SOX + NOX). After long-term autoclave treatment with impure scCO2, the sandstone samples exhibit modified strength parameters and elastic deformation behaviour as well as changes in porosity compared to untreated samples. Furthermore, the injected fluid volume into the pore space of sandstones from the same lithotype varies during triaxial loading depending on the chemistry of the pore fluid. CO2 with NOX and SOX bearing fluid fills a significantly larger proportion of the sandstone pore space than brine with pure scCO2. * The

Anatomy of anomalously thick sandstone units in the Brent Delta of the northern North Sea

Science.gov (United States)

Wei, Xiaojie; Steel, Ronald J.; Ravnås, Rodmar; Jiang, Zaixing; Olariu, Cornel; Ma, Yinsheng

2018-05-01

Some potentially attractive reservoirs, containing anomalously thick (10s to a few 100 m), cross-stratified sandstone, have been locally encountered within both the classic regressive (lower Brent) and the transgressive (upper Brent) segments of the Brent Delta. Three documented cases of these sandstone bodies are re-examined. They are internally dominated by simple or compound dunes, and typified by two types of deepening-upward succession, recording a retrogradational or transgressive shoreline history. Type I is expressed as a single estuarine succession changing upwards from erosive, coarse-grained channelized deposits into outer estuary tidal bar deposits. The estuary is underlain and overlain by deltaic deposits. Type II lacks significant basal river deposits but is composed by stacked mixed-energy and tide-dominated estuarine deposits. It is underlain by deltaic deposits and overlain by open marine sediments. Considering the structural evolution in the northern North Sea basin, we suggest (as did some earlier researchers) that these sandstone bodies were local, but sometimes broad transgressive estuaries, formed at any time during large-scale Brent Delta growth and decay. The estuary generation was likely triggered by fluvial incision coupled with active faulting, producing variable accommodation embayments, where tidal currents became focused and deposition became transgressive. The spatial variations of the interpreted estuary deposits were linked with variable, fault-generated accommodation. The relatively simple, lower Brent estuarine units were created by short-lived, fault activity in places, whereas the complex, stacked upper-Brent estuarine units were likely a result of more long-lived, punctuated fault-induced subsidence leading into the northern North Sea main rifting stage. The thick cross-stratified units potentially accumulated in the hangingwall of large bounding faults.

Petroacoustic Modelling of Heterolithic Sandstone Reservoirs: A Novel Approach to Gassmann Modelling Incorporating Sedimentological Constraints and NMR Porosity data

Science.gov (United States)

Matthews, S.; Lovell, M.; Davies, S. J.; Pritchard, T.; Sirju, C.; Abdelkarim, A.

2012-12-01

Heterolithic or 'shaly' sandstone reservoirs constitute a significant proportion of hydrocarbon resources. Petroacoustic models (a combination of petrophysics and rock physics) enhance the ability to extract reservoir properties from seismic data, providing a connection between seismic and fine-scale rock properties. By incorporating sedimentological observations these models can be better constrained and improved. Petroacoustic modelling is complicated by the unpredictable effects of clay minerals and clay-sized particles on geophysical properties. Such effects are responsible for erroneous results when models developed for "clean" reservoirs - such as Gassmann's equation (Gassmann, 1951) - are applied to heterolithic sandstone reservoirs. Gassmann's equation is arguably the most popular petroacoustic modelling technique in the hydrocarbon industry and is used to model elastic effects of changing reservoir fluid saturations. Successful implementation of Gassmann's equation requires well-constrained drained rock frame properties, which in heterolithic sandstones are heavily influenced by reservoir sedimentology, particularly clay distribution. The prevalent approach to categorising clay distribution is based on the Thomas - Stieber model (Thomas & Stieber, 1975), this approach is inconsistent with current understanding of 'shaly sand' sedimentology and omits properties such as sorting and grain size. The novel approach presented here demonstrates that characterising reservoir sedimentology constitutes an important modelling phase. As well as incorporating sedimentological constraints, this novel approach also aims to improve drained frame moduli estimates through more careful consideration of Gassmann's model assumptions and limitations. A key assumption of Gassmann's equation is a pore space in total communication with movable fluids. This assumption is often violated by conventional applications in heterolithic sandstone reservoirs where effective porosity, which

Topological representation of the porous structure and its evolution of reservoir sandstone under excavation-induced loads

Directory of Open Access Journals (Sweden)

Ju Yang

2017-01-01

Full Text Available The porous structure of a reservoir rock greatly influences its evolutive deformation and fracture behavior during excavation of natural resources reservoirs. Most numerical models for porous structures have been used to predict the quasi-static mechanical properties, but few are available to accurately characterize the evolution process of the porous structure and its influence on the macroscopic properties of reservoir rocks. This study reports a novel method to characterize the porous structure of sandstone using its topological parameters and to determine the laws that govern the evolutive deformation and failure of the topological structure under various uniaxial compressive loads. A numerical model of the porous sandstone was established based on the pore characteristics that were acquired using computed tomography imaging techniques. The analytical method that integrates the grassfire algorithm and the maximum inscribed sphere algorithm was proposed to create the 3-D topological model of the deformed porous structure, through which the topological parameters of the structure were measured and identified. The evolution processes of the porous structure under various loads were characterized using its equivalent topological model and parameters. This study opens a new way to characterize the dynamic evolution of the pore structure of reservoir sandstone under excavation disturbance.

Permeability model of tight reservoir sandstones combining core-plug and miniperm analysis of drillcore; longyearbyen co2lab, Svalbard

NARCIS (Netherlands)

Magnabosco, Cara; Braathen, Alvar; Ogata, Kei

2014-01-01

Permeability measurements in Mesozoic, low-permeability sandstone units within the strata cored in seven drillholes near Longyearbyen, Svalbard, have been analysed to assess the presence of aquifers and their potentials as reservoirs for the storage of carbon dioxide. These targeted sandstones are

Study of the Effect of Clay Particles on Low Salinity Water Injection in Sandstone Reservoirs

Directory of Open Access Journals (Sweden)

Sina Rezaei Gomari

2017-03-01

Full Text Available The need for optimal recovery of crude oil from sandstone and carbonate reservoirs around the world has never been greater for the petroleum industry. Water-flooding has been applied to the supplement primary depletion process or as a separate secondary recovery method. Low salinity water injection is a relatively new method that involves injecting low salinity brines at high pressure similar to conventional water-flooding techniques, in order to recover crude oil. The effectiveness of low salinity water injection in sandstone reservoirs depends on a number of parameters such as reservoir temperature, pressure, type of clay particle and salinity of injected brine. Clay particles present on reservoir rock surfaces adsorb polar components of oil and modify wettability of sandstone rocks to the oil-wet state, which is accountable for the reduced recovery rates by conventional water-flooding. The extent of wettability alteration caused by three low salinity brines on oil-wet sandstone samples containing varying clay content (15% or 30% and type of clay (kaolinite/montmorillonite were analyzed in the laboratory experiment. Contact angles of mica powder and clay mixture (kaolinite/montmorillonite modified with crude oil were measured before and after injection with three low salinity sodium chloride brines. The effect of temperature was also analyzed for each sample. The results of the experiment indicate that samples with kaolinite clay tend to produce higher contact angles than samples with montmorillonite clay when modified with crude oil. The highest degree or extent of wettability alteration from oil-wet to intermediate-wet state upon injection with low salinity brines was observed for samples injected with brine having salinity concentration of 2000 ppm. The increase in temperature tends to produce contact angles values lying in the higher end of the intermediate-wet range (75°–115° for samples treated at 50 °C, while their corresponding

Low permeability Neogene lithofacies in Northern Croatia as potential unconventional hydrocarbon reservoirs

Science.gov (United States)

Malvić, Tomislav; Sučić, Antonija; Cvetković, Marko; Resanović, Filip; Velić, Josipa

2014-06-01

We present two examples of describing low permeability Neogene clastic lithofacies to outline unconventional hydrocarbon lithofacies. Both examples were selected from the Drava Depression, the largest macrostructure of the Pannonian Basin System located in Croatia. The first example is the Beničanci Field, the largest Croatian hydrocarbon reservoir discovered in Badenian coarse-grained clastics that consists mostly of breccia. The definition of low permeability lithofacies is related to the margins of the existing reservoir, where the reservoir lithology changed into a transitional one, which is mainly depicted by the marlitic sandstones. However, calculation of the POS (probability of success of new hydrocarbons) shows critical geological categories where probabilities are lower than those in the viable reservoir with proven reserves. Potential new hydrocarbon volumes are located in the structural margins, along the oil-water contact, with a POS of 9.375%. These potential reserves in those areas can be classified as probable. A second example was the Cremušina Structure, where a hydrocarbon reservoir was not proven, but where the entire structure has been transferred onto regional migration pathways. The Lower Pontian lithology is described from well logs as fine-grained sandstones with large sections of silty or marly clastics. As a result, the average porosity is low for conventional reservoir classification (10.57%). However, it is still an interesting case for consideration as a potentially unconventional reservoir, such as the "tight" sandstones.

REE characteristics and uranium metallogenesis of sandstone-type uranium deposits in northern Sichuan

International Nuclear Information System (INIS)

Zhu Xiyang; Wang Yunliang; Wang Zhichang; Zhang Chengjiang

2004-01-01

On the basis of the analysis of a large number of samples at sandstone-type uranium deposits in northern Sichuan, this paper analyses the REE composition of country rocks, ores, calcite-veins and uranium minerals, and systematically summarizes their REE geochemical characteristics, and discusses variation regularity of REE during depositional and diagenetic processes. By comparing these characteristics with those of typical hydrothermal volcanics-type and metamorphic rock type uranium deposits both at home and abroad, authors suggest that sandstone-type uranium deposits in northern Sichuan are characterized by REE geochemical features of hydrothermal reworking metallogenesis, the uranium mineralization has experienced two stages: the diagenetic preconcentration and the concentration of hydrothermal reworking

Qualitative and quantitative changes in detrital reservoir rocks caused by CO2-brine-rock interactions during first injection phases (Utrillas sandstones, northern Spain)

Science.gov (United States)

Berrezueta, E.; Ordóñez-Casado, B.; Quintana, L.

2016-01-01

The aim of this article is to describe and interpret qualitative and quantitative changes at rock matrix scale of lower-upper Cretaceous sandstones exposed to supercritical (SC) CO2 and brine. The effects of experimental injection of CO2-rich brine during the first injection phases were studied at rock matrix scale, in a potential deep sedimentary reservoir in northern Spain (Utrillas unit, at the base of the Cenozoic Duero Basin).Experimental CO2-rich brine was exposed to sandstone in a reactor chamber under realistic conditions of deep saline formations (P ≈ 7.8 MPa, T ≈ 38 °C and 24 h exposure time). After the experiment, exposed and non-exposed equivalent sample sets were compared with the aim of assessing possible changes due to the effect of the CO2-rich brine exposure. Optical microscopy (OpM) and scanning electron microscopy (SEM) aided by optical image analysis (OIA) were used to compare the rock samples and get qualitative and quantitative information about mineralogy, texture and pore network distribution. Complementary chemical analyses were performed to refine the mineralogical information and to obtain whole rock geochemical data. Brine composition was also analyzed before and after the experiment.The petrographic study of contiguous sandstone samples (more external area of sample blocks) before and after CO2-rich brine injection indicates an evolution of the pore network (porosity increase ≈ 2 %). It is probable that these measured pore changes could be due to intergranular quartz matrix detachment and partial removal from the rock sample, considering them as the early features produced by the CO2-rich brine. Nevertheless, the whole rock and brine chemical analyses after interaction with CO2-rich brine do not present important changes in the mineralogical and chemical configuration of the rock with respect to initial conditions, ruling out relevant precipitation or dissolution at these early stages to rock-block scale. These results

Muddy and dolomitic rip-up clasts in Triassic fluvial sandstones: Origin and impact on potential reservoir properties (Argana Basin, Morocco)

Science.gov (United States)

Henares, Saturnina; Arribas, Jose; Cultrone, Giuseppe; Viseras, Cesar

2016-06-01

The significance of rip-up clasts as sandstone framework grains is frequently neglected in the literature being considered as accessory components in bulk sandstone composition. However, this study highlights the great value of muddy and dolomitic rip-up clast occurrence as: (a) information source about low preservation potential from floodplain deposits and (b) key element controlling host sandstone diagenetic evolution and thus ultimate reservoir quality. High-resolution petrographic analysis on Triassic fluvial sandstones from Argana Basin (T6 and T7/T8 units) highlights the significance of different types of rip-up clasts as intrabasinal framework components of continental sediments from arid climates. On the basis of their composition and ductility, three main types are distinguished: (a) muddy rip-up clasts, (b) dolomitic muddy rip-up clasts and (c) dolomite crystalline rip-up clasts. Spatial distribution of different types is strongly facies-related according to grain size. Origin of rip-up clasts is related to erosion of coeval phreatic dolocretes, in different development stages, and associated muddy floodplain sediments. Cloudy cores with abundant inclusions and clear outer rims of dolomite crystals suggest a first replacive and a subsequent displacive growth, respectively. Dolomite crystals are almost stoichiometric. This composition is very similar to that of early sandstone dolomite cement, supporting phreatic dolocretes as dolomite origin in both situations. Sandstone diagenesis is dominated by mechanical compaction and dolomite cementation. A direct correlation exists between: (1) muddy rip-up clast abundance and early reduction of primary porosity by compaction with irreversible loss of intergranular volume (IGV); and (2) occurrence of dolomitic rip-up clasts and dolomite cement nucleation in host sandstone, occluding adjacent pores but preserving IGV. Both processes affect reservoir quality by generation of vertical and 3D fluid flow baffles and

Estimation of porosity of Khewra sandstone of cambrian age by using helium porosimeter and its application in reservoir evaluation

International Nuclear Information System (INIS)

Khan, M.S.; Bhatti, A.A.; Gillani, S.T.A.; Raza, A.

2012-01-01

Estimation of petrophysical properties of the rock formations played decisive role in all the processes of petroleum exploration. The Cambrian sequence is well established as reservoir rocks in the various parts of the world from where petroleum is being tapped. The Cambrian sequence has been encountered in the Potwar area and limited petroleum is being produced from the Adhi Oil Field. The Khewra Sandstone of the Cambrian sequence is outcropped in the Khewra Gorge, Salt Range Pakistan below an unconformity qf the Tobra Formation. For the assessment of porosity and reservoir characterization Helium Porosimeter has been used, six samples Qf the upper horizon were collected from various locations of the Khewra Gorge and the Khewra Choha Sadden Shah road side section; cores were prepared from these samples according to the instrument standard. The results of this study revealed that the upper horizon Qf the Khewra Sandstone Formation has good porosity ranging from 18.76% to 21.07%, porosity varied in different parts of the formation. These results are in good agreement with the internationally reported values for petroleum reservoir of the Cambrian sandstone. (author)

Diagenesis and reservoir quality of Bhuban sandstones (Neogene), Titas Gas Field, Bengal Basin, Bangladesh

Science.gov (United States)

Aminul Islam, M.

2009-06-01

This study deals with the diagenesis and reservoir quality of sandstones of the Bhuban Formation located at the Titas Gas Field of Bengal Basin. Petrographic study including XRD, CL, SEM and BSE image analysis and quantitative determination of reservoir properties were carried out for this study. The sandstones are fine to medium-grained, moderately well to well sorted subfeldspathic arenites with subordinate feldspathic and lithic arenites. The diagenetic processes include clay infiltration, compaction and cementation (quartz overgrowth, chlorite, kaolinite, calcite and minor amount of pyrite, dolomite and K-feldspar overgrowth). Quartz is the dominant pore occluding cement and generally occurred as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Pressure solution derived from grain contact is the main contributor of quartz overgrowths. Chlorite occurs as pore-lining and pore filling cement. In some cases, chlorite helps to retain porosity by preventing quartz overgrowth. In some restricted depth interval, pore-occlusion by calcite cement is very much intense. Kaolinite locally developed as vermiform and accelerated the minor porosity loss due to pore-occlusion. Kaolinite/chlorite enhances ineffective microporosity. Kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene or deeper Oligocene source rocks. The relation between diagenesis and reservoir quality is as follows: the initial porosity was decreased by compaction and cementation and then increased by leaching of the metastable grains and dissolution of cement. Good quality reservoir rocks were deposited in fluvial environment and hence quality of reservoir rocks is also environment selective. Porosity and permeability data exhibit good inverse correlation with cement. However, some data points indicate multiple controls on permeability. Reservoir quality is thus controlled by

Experimental evaluation on the damages of different drilling modes to tight sandstone reservoirs

Directory of Open Access Journals (Sweden)

Gao Li

2017-07-01

Full Text Available The damages of different drilling modes to reservoirs are different in types and degrees. In this paper, the geologic characteristics and types of such damages were analyzed. Then, based on the relationship between reservoir pressure and bottom hole flowing pressure corresponding to different drilling modes, the experimental procedures on reservoir damages in three drilling modes (e.g. gas drilling, liquid-based underbalanced drilling and overbalanced drilling were designed. Finally, damage simulation experiments were conducted on the tight sandstone reservoir cores of the Jurassic Ahe Fm in the Tarim Basin and Triassic Xujiahe Fm in the central Sichuan Basin. It is shown that the underbalanced drilling is beneficial to reservoir protection because of its less damage on reservoir permeability, but it is, to some extent, sensitive to the stress and the empirical formula of stress sensitivity coefficient is obtained; and that the overbalanced drilling has more reservoir damages due to the invasion of solid and liquid phases. After the water saturation of cores rises to the irreducible water saturation, the decline of gas logging permeability speeds up and the damage degree of water lock increases. It is concluded that the laboratory experiment results of reservoir damage are accordant with the reservoir damage characteristics in actual drilling conditions. Therefore, this method reflects accurately the reservoir damage characteristics and can be used as a new experimental evaluation method on reservoir damage in different drilling modes.

Prospect analysis for sandstone-type uranium mineralization in the northern margin of Qaidam basin

International Nuclear Information System (INIS)

Liu Lin; Song Xiansheng; Feng Wei; Song Zhe; Li Wei

2010-01-01

Affected by the regional geological structural evolution, a set of sedimentary structure, i.e. the construction of coal-bearing classic rocks which is in favor of the sandstone-type uranium mineralization has deposited in the northern margin of Qaidam Basin since Meso-Cenozoic. A NWW thrust nappe tectonic belt, i.e. the ancient tectonic belt which is the basis for the development of ancient interlayer oxidation zone formed by the tectonic reverse in late Jurassic and Cretaceous. The Mid and late Jurassic layer was buried by the weak extension in Paleogene and the depression in early Neogene. The extrusion reversal from late Neogene to Quaternary made the basin into the development era of the modern interlayer oxidation zone. It can be concluded that the layer of the northern margin of Qaidam Basin has the premise for the formation of sandstone-type uranium ore. Based on the analysis of the characteristics of the thrust belt, the structure of the purpose layer, the sand body, the hydrogeology, the interlayer oxidation zone and uranium mineralization, the results indicated that the ancient interlayer oxidation zone is the prospecting type of sandstone-type uranium ore. Beidatan and the east of Yuqia are the favorable prospective area of sandstone-type uranium mineralization. (authors)

Characterization of the Qishn sandstone reservoir, Masila Basin-Yemen, using an integrated petrophysical and seismic structural approach

Science.gov (United States)

Lashin, Aref; Marta, Ebrahim Bin; Khamis, Mohamed

2016-03-01

This study presents an integrated petrophysical and seismic structural analysis that is carried out to evaluate the reservoir properties of Qishn sandstone as well as the entrapment style of the hydrocarbons at Sharyoof field, Sayun-Masila Basin that is located at the east central of Yemen. The reservoir rocks are dominated by clean porous and permeable sandstones zones usually intercalated with some clay stone interbeds. As identified from well logs, Qishn sandstone is classified into subunits (S1A, S1B, S1C and S2) with different reservoir characteristics and hydrocarbon potentiality. A number of qualitative and quantitative well logging analyses are used to characterize the different subunits of the Qishn reservoir and identify its hydrocarbon potentiality. Dia-porosity, M-N, Pickett, Buckles plots, petrophysical analogs and lateral distribution maps are used in the analysis. Shale volume, lithology, porosity, and fluid saturation are among the most important deduced parameters. The analysis revealed that S1A and S1C are the main hydrocarbon-bearing units. More specifically, S1A unit is the best, as it attains the most prolific hydrocarbon saturations (oil saturation "SH″ up to 65) and reservoir characteristics. An average petrophysical ranges of 4-21%, 16-23%, 11-19%, 0-65%, are detected for S1A unit, regarding shale volume, total and effective porosity, and hydrocarbon saturation, respectively. Meanwhile, S1B unit exhibits less reservoir characteristics (Vsh>30%, ϕEff<15% and SH< 15%). The lateral distribution maps revealed that most of the hydrocarbons (for S1A and S1C units) are indicated at the middle of the study area as NE-SW oriented closures. The analysis and interpretation of seismic data had clarified that the structure of study area is represented by a big middle horst bounded by a group of step-like normal faults at the extreme boundaries (faulted anticlinal-structure). In conclusion, the entrapment of the encountered hydrocarbon at Sharyoof oil

Understanding creep in sandstone reservoirs - theoretical deformation mechanism maps for pressure solution in granular materials

Science.gov (United States)

Hangx, Suzanne; Spiers, Christopher

2014-05-01

Subsurface exploitation of the Earth's natural resources removes the natural system from its chemical and physical equilibrium. As such, groundwater extraction and hydrocarbon production from subsurface reservoirs frequently causes surface subsidence and induces (micro)seismicity. These effects are not only a problem in onshore (e.g. Groningen, the Netherlands) and offshore hydrocarbon fields (e.g. Ekofisk, Norway), but also in urban areas with extensive groundwater pumping (e.g. Venice, Italy). It is known that fluid extraction inevitably leads to (poro)elastic compaction of reservoirs, hence subsidence and occasional fault reactivation, and causes significant technical, economic and ecological impact. However, such effects often exceed what is expected from purely elastic reservoir behaviour and may continue long after exploitation has ceased. This is most likely due to time-dependent compaction, or 'creep deformation', of such reservoirs, driven by the reduction in pore fluid pressure compared with the rock overburden. Given the societal and ecological impact of surface subsidence, as well as the current interest in developing geothermal energy and unconventional gas resources in densely populated areas, there is much need for obtaining better quantitative understanding of creep in sediments to improve the predictability of the impact of geo-energy and groundwater production. The key problem in developing a reliable, quantitative description of the creep behaviour of sediments, such as sands and sandstones, is that the operative deformation mechanisms are poorly known and poorly quantified. While grain-scale brittle fracturing plus intergranular sliding play an important role in the early stages of compaction, these time-independent, brittle-frictional processes give way to compaction creep on longer time-scales. Thermally-activated mass transfer processes, like pressure solution, can cause creep via dissolution of material at stressed grain contacts, grain

Geothermal characteristics of Buntsandstein sandstone reservoir of Alsace

International Nuclear Information System (INIS)

Haffen, Sebastien

2012-01-01

The Buntsandstein, located in the Upper Rhine Graben, appears to be an easy target for geothermal exploitation, linking sandstone and clay with the regional thermal anomaly. This study aims at characterizing petrophysical characteristics of these sandstones as well as the fracturing affecting them, with the intention of providing a conceptual model of the formation which will act as guide for future exploitation. The sedimentary facies are composed by five petrographical facies (clean sandstones, sandstones with clayey coating, clay matrix sandstones, silicified sandstones and carbonated matrix sandstones) which split with variable proportions and control a part of petrophysical properties measured at matrix scale. The comparison between petrophysical data, macroscopic data from temperature gradient analysis, modelling data and fracturing, allows the building of a Buntsandstein Sandstones fluids circulation conceptual model. This analysis points the role of the damage zone of fault zones for fluids transfer at large scale, but also that of two sedimentary facies: marginal erg and Playa Lake. The analysis of different outcrops shows that the fracturing evolves according to the situation in the sedimentary pile and according to the situation in comparison with major tectonic accidents. (author) [fr

Hydrogeology of the Potsdam Sandstone in northern New York

Science.gov (United States)

Williams, John H.; Reynolds, Richard J.; Franzi, David A.; Romanowicz, Edwin A.; Paillet, Frederick L.

2010-01-01

The Potsdam Sandstone of Cambrian age forms a transboundary aquifer that extends across northern New York and into southern Quebec. The Potsdam Sandstone is a gently dipping sequence of arkose, subarkose, and orthoquartzite that unconformably overlies Precambrian metamorphic bedrock. The Potsdam irregularly grades upward over a thickness of 450 m from a heterogeneous feldspathic and argillaceous rock to a homogeneous, quartz-rich and matrix-poor rock. The hydrogeological framework of the Potsdam Sandstone was investigated through an analysis of records from 1,500 wells and geophysical logs from 40 wells, and through compilation of GIS coverages of bedrock and surficial geology, examination of bedrock cores, and construction of hydrogeological sections. The upper several metres of the sandstone typically is weathered and fractured and, where saturated, readily transmits groundwater. Bedding-related fractures in the sandstone commonly form sub-horizontal flow zones of relatively high transmissivity. The vertical distribution of sub-horizontal flow zones is variable; spacings of less than 10 m are common. Transmissivity of individual flow zones may be more than 100 m2/d but typically is less than 10 m2/d. High angle fractures, including joints and faults, locally provide vertical hydraulic connection between flow zones. Hydraulic head gradients in the aquifer commonly are downward; a laterally extensive series of sub-horizontal flow zones serve as drains for the groundwater flow system. Vertical hydraulic head differences between shallow and deep flow zones range from 1 m to more than 20 m. The maximum head differences are in recharge areas upgradient from the area where the Chateauguay and Chazy Rivers, and their tributaries, have cut into till and bedrock. Till overlies the sandstone in much of the study area; its thickness is generally greatest in the western part, where it may exceed 50 m. A discontinuous belt of bedrock pavements stripped of glacial drift extends

Provenance, diagenesis, tectonic setting and reservoir quality of the sandstones of the Kareem Formation, Gulf of Suez, Egypt

Science.gov (United States)

Zaid, Samir M.

2013-09-01

The Middle Miocene Kareem sandstones are important oil reservoirs in the southwestern part of the Gulf of Suez basin, Egypt. However, their diagenesis and provenance and their impact on reservoir quality, are virtually unknown. Samples from the Zeit Bay Oil Field, and the East Zeit Oil Field represent the Lower Kareem (Rahmi Member) and the Upper Kareem (Shagar Member), were studied using a combination of petrographic, mineralogical and geochemical techniques. The Lower Rahmi sandstones have an average framework composition of Q95F3.4R1.6, and 90% of the quartz grains are monocrystalline. By contrast, the Upper Shagar sandstones are only slightly less quartzose with an average framework composition of Q76F21R3 and 82% of the quartz grains are monocrystalline. The Kareem sandstones are mostly quartzarenite with subordinate subarkose and arkose. Petrographical and geochemical data of sandstones indicate that they were derived from granitic and metamorphic terrains as the main source rock with a subordinate quartzose recycled sedimentary rocks and deposited in a passive continental margin of a syn rift basin. The sandstones of the Kareem Formation show upward decrease in maturity. Petrographic study revealed that dolomite is the dominant cement and generally occurs as fine to medium rhombs pore occluding phase and locally as a grain replacive phase. Authigenic quartz occurs as small euhedral crystals, locally as large pyramidal crystals in the primary pores. Authigenic anhydrites typically occur as poikilotopic rhombs or elongate laths infilling pores but also as vein filling cement. The kaolinite is a by-product of feldspar leaching in the presence of acidic fluid produced during the maturation of organic matter in the adjacent Miocene rocks. Diagenetic features include compaction; dolomite, silica and anhydrite cementation with minor iron-oxide, illite, kaolinite and pyrite cements; dissolution of feldspars, rock fragments. Silica dissolution, grain replacement and

Reservoir characterization of the Mt. Simon Sandstone, Illinois Basin, USA

Science.gov (United States)

Frailey, S.M.; Damico, J.; Leetaru, H.E.

2011-01-01

The integration of open hole well log analyses, core analyses and pressure transient analyses was used for reservoir characterization of the Mt. Simon sandstone. Characterization of the injection interval provides the basis for a geologic model to support the baseline MVA model, specify pressure design requirements of surface equipment, develop completion strategies, estimate injection rates, and project the CO2 plume distribution.The Cambrian-age Mt. Simon Sandstone overlies the Precambrian granite basement of the Illinois Basin. The Mt. Simon is relatively thick formation exceeding 800 meters in some areas of the Illinois Basin. In the deeper part of the basin where sequestration is likely to occur at depths exceeding 1000 m, horizontal core permeability ranges from less than 1 ?? 10-12 cm 2 to greater than 1 ?? 10-8 cm2. Well log and core porosity can be up to 30% in the basal Mt. Simon reservoir. For modeling purposes, reservoir characterization includes absolute horizontal and vertical permeability, effective porosity, net and gross thickness, and depth. For horizontal permeability, log porosity was correlated with core. The core porosity-permeability correlation was improved by using grain size as an indication of pore throat size. After numerous attempts to identify an appropriate log signature, the calculated cementation exponent from Archie's porosity and resistivity relationships was used to identify which porosity-permeability correlation to apply and a permeability log was made. Due to the relatively large thickness of the Mt. Simon, vertical permeability is an important attribute to understand the distribution of CO2 when the injection interval is in the lower part of the unit. Only core analyses and specifically designed pressure transient tests can yield vertical permeability. Many reservoir flow models show that 500-800 m from the injection well most of the CO2 migrates upward depending on the magnitude of the vertical permeability and CO2 injection

Geological and petrophysical characterization of the Ferron Sandstone for 3-D simulation of a fluvial-deltaic reservoir. Deliverable 2.5.4, Ferron Sandstone lithologic strip logs, Emergy & Sevier Counties, Utah: Volume I

Energy Technology Data Exchange (ETDEWEB)

Allison, M.L.

1995-12-08

Strip logs for 491 wells were produced from a digital subsurface database of lithologic descriptions of the Ferron Sandstone Member of the Mancos Shale. This subsurface database covers wells from the parts of Emery and Sevier Counties in central Utah that occur between Ferron Creek on the north and Last Chance Creek on the south. The lithologic descriptions were imported into a logging software application designed for the display of stratigraphic data. Strip logs were produced at a scale of one inch equals 20 feet. The strip logs were created as part of a study by the Utah Geological Survey to develop a comprehensive, interdisciplinary, and qualitative characterization of a fluvial-deltaic reservoir using the Ferron Sandstone as a surface analogue. The study was funded by the U.S. Department of Energy (DOE) under the Geoscience/Engineering Reservoir Characterization Program.

Cathodoluminescence, fluid inclusions and trace element data for the syntaxial quartz cementation in the sandstones of Ora Formation, northern Iraq

DEFF Research Database (Denmark)

Omer, Muhamed Fakhri; Friis, Henrik

2018-01-01

Quartz cements of the quartz arenitic sandstones from the Chalky Nasara and Ora section of the (Devonian-Carboniferous) Ora Formation in northern Iraq have been studied. A combination of Hot-Cathodoluminescence (CL), LA-ICP-MS and fluid inclusions microthermometry revealed three syntaxial quartz......-bedded sandstones than in the6 thickly-bedded sandstones filling most of remaining pore space during mesogenesis. The Q3 was formed during early telogenesis stage fully cementing the sandstones and the fractures were filled by hydrothermal chlorite and sulfides. Significant amount of trace elements Al, Li, Ge...

Study on fine geological modelling of the fluvial sandstone reservoir in Daqing oilfield

Energy Technology Data Exchange (ETDEWEB)

Zhoa Han-Qing [Daqing Research Institute, Helongjiang (China)

1997-08-01

These paper aims at developing a method for fine reservoir description in maturing oilfields by using close spaced well logging data. The main productive reservoirs in Daqing oilfield is a set of large fluvial-deltaic deposits in the Songliao Lake Basin, characterized by multi-layers and serious heterogeneities. Various fluvial channel sandstone reservoirs cover a fairly important proportion of reserves. After a long period of water flooding, most of them have turned into high water cut layers, but there are considerable residual reserves within them, which are difficult to find and tap. Making fine reservoir description and developing sound a geological model is essential for tapping residual oil and enhancing oil recovery. The principal reason for relative lower precision of predicting model developed by using geostatistics is incomplete recognition of complex distribution of fluvial reservoirs and their internal architecture`s. Tasking advantage of limited outcrop data from other regions (suppose no outcrop data available in oilfield) can only provide the knowledge of subtle changing of reservoir parameters and internal architecture. For the specific geometry distribution and internal architecture of subsurface reservoirs (such as in produced regions) can be gained only from continuous infilling logging well data available from studied areas. For developing a geological model, we think the first important thing is to characterize sandbodies geometries and their general architecture`s, which are the framework of models, and then the slight changing of interwell parameters and internal architecture`s, which are the contents and cells of the model. An excellent model should possess both of them, but the geometry is the key to model, because it controls the contents and cells distribution within a model.

Predictive modeling of CO2 sequestration in deep saline sandstone reservoirs: Impacts of geochemical kinetics

Energy Technology Data Exchange (ETDEWEB)

Balashov, Victor N.; Guthrie, George D.; Hakala, J. Alexandra; Lopano, Christina L.; Rimstidt, J. Donald; Brantley, Susan L.

2013-03-01

One idea for mitigating the increase in fossil-fuel generated CO{sub 2} in the atmosphere is to inject CO{sub 2} into subsurface saline sandstone reservoirs. To decide whether to try such sequestration at a globally significant scale will require the ability to predict the fate of injected CO{sub 2}. Thus, models are needed to predict the rates and extents of subsurface rock-water-gas interactions. Several reactive transport models for CO{sub 2} sequestration created in the last decade predicted sequestration in sandstone reservoirs of ~17 to ~90 kg CO{sub 2} m{sup -3|. To build confidence in such models, a baseline problem including rock + water chemistry is proposed as the basis for future modeling so that both the models and the parameterizations can be compared systematically. In addition, a reactive diffusion model is used to investigate the fate of injected supercritical CO{sub 2} fluid in the proposed baseline reservoir + brine system. In the baseline problem, injected CO{sub 2} is redistributed from the supercritical (SC) free phase by dissolution into pore brine and by formation of carbonates in the sandstone. The numerical transport model incorporates a full kinetic description of mineral-water reactions under the assumption that transport is by diffusion only. Sensitivity tests were also run to understand which mineral kinetics reactions are important for CO{sub 2} trapping. The diffusion transport model shows that for the first ~20 years after CO{sub 2} diffusion initiates, CO{sub 2} is mostly consumed by dissolution into the brine to form CO{sub 2,aq} (solubility trapping). From 20-200 years, both solubility and mineral trapping are important as calcite precipitation is driven by dissolution of oligoclase. From 200 to 1000 years, mineral trapping is the most important sequestration mechanism, as smectite dissolves and calcite precipitates. Beyond 2000 years, most trapping is due to formation of aqueous HCO{sub 3}{sup -}. Ninety-seven percent of the

Feasibility of microbially improved oil recovery (MIOR) in Northern German oil reservoirs; Bakterien zur Erhoehung des Entoelungsgrades in norddeutschen Erdoellagerstaetten

Energy Technology Data Exchange (ETDEWEB)

Amro, M. [Inst. fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany); Kessel, D. [Inst. fuer Erdoel- und Erdgasforschung, Clausthal-Zellerfeld (Germany)

1996-05-01

The scope of this study was to investigate the feasibility of microbially improved oil recovery (MIOR) in Northern German oil reservoirs. Suitable bacterial strains had to be identified. The mechanisms for oil mobilization and incremental recovery had to be investigated. To this end, two independent methods were employed, namely static autoclave tests and dynamic flood experiments. The static tests were carried out without reservoir rock matrix to preselect suitable bacterial strains with a minimum of experimental effort. The selected strains were then tested in dynamic flood experiments under reservoir conditions on Bentheimer sandstone cores to quantify the oil recovery. Key results of the study are: (1) Two bacterial strains were found having excellent metabolic activity with potential for oil recovery under Northern German reservoir conditions. (2) These bacteria can be injected into and transported in the pores of the sandstone. (3) The metabolic activity of these bacteria leads to substantial incremental oil recovery in repeated injection - shut in - production cycles. (4) Incremental oil recovery is attributed to wettability change and biomass production by the metabolites of the bacteria. (orig.) [Deutsch] Das Ziel dieser Arbeit ist die Untersuchung der Anwendbarkeit der mikrobiell verbesserten Erdoelgewinnung in norddeutschen Lagerstaetten. Zunaechst waren hierfuer einsetzbare Bakterienstaemme zu identifizieren. Diese waren dann auf ihr Entoelungsvermoegen zu ueberpruefen. Schliesslich sollten die Entoelungsmechanismen ermittelt werden. Die Vorauswahl potentiell geeigneter Bakterienstaemme erfolgte durch verschiedene mikrobiologische Forschungsinstitute. Zur Minimierung des experimentellen Aufwands wurden diese Staemme dann im Institut fuer Erdoel- und Erdgasforschung in statischen Autoklavenversuchen unter Lagerstaettenbedingungen, jedoch noch ohne Lagerstaettengestein, auf ihre Stoffwechselaktivitaet sowie Art und Eigenschaften ihrer Stoffwechselprodukte

Performance of Surfactant Methyl Ester Sulphonate solution for Oil Well Stimulation in reservoir sandstone TJ Field

Science.gov (United States)

Eris, F. R.; Hambali, E.; Suryani, A.; Permadi, P.

2017-05-01

Asphaltene, paraffin, wax and sludge deposition, emulsion and water blocking are kinds ofprocess that results in a reduction of the fluid flow from the reservoir into formation which causes a decrease of oil wells productivity. Oil well Stimulation can be used as an alternative to solve oil well problems. Oil well stimulation technique requires applying of surfactant. Sodium Methyl Ester Sulphonate (SMES) of palm oil is an anionic surfactant derived from renewable natural resource that environmental friendly is one of potential surfactant types that can be used in oil well stimulation. This study was aimed at formulation SMES as well stimulation agent that can identify phase transitions to phase behavior in a brine-surfactant-oil system and altered the wettability of rock sandstone and limestone. Performance of SMES solution tested by thermal stability test, phase behavioral examination and rocks wettability test. The results showed that SMES solution (SMES 5% + xylene 5% in the diesel with addition of 1% NaCl at TJformation water and SMES 5% + xylene 5% in methyl ester with the addition of NaCl 1% in the TJ formation water) are surfactant that can maintain thermal stability, can mostly altered the wettability toward water-wet in sandstone reservoir, TJ Field.

Digital Rock Physics Aplications: Visualisation Complex Pore and Porosity-Permeability Estimations of the Porous Sandstone Reservoir

Science.gov (United States)

Handoyo; Fatkhan; Del, Fourier

2018-03-01

Reservoir rock containing oil and gas generally has high porosity and permeability. High porosity is expected to accommodate hydrocarbon fluid in large quantities and high permeability is associated with the rock’s ability to let hydrocarbon fluid flow optimally. Porosity and permeability measurement of a rock sample is usually performed in the laboratory. We estimate the porosity and permeability of sandstones digitally by using digital images from μCT-Scan. Advantages of the method are non-destructive and can be applied for small rock pieces also easily to construct the model. The porosity values are calculated by comparing the digital image of the pore volume to the total volume of the sandstones; while the permeability values are calculated using the Lattice Boltzmann calculations utilizing the nature of the law of conservation of mass and conservation of momentum of a particle. To determine variations of the porosity and permeability, the main sandstone samples with a dimension of 300 × 300 × 300 pixels are made into eight sub-cubes with a size of 150 × 150 × 150 pixels. Results of digital image modeling fluid flow velocity are visualized as normal velocity (streamline). Variations in value sandstone porosity vary between 0.30 to 0.38 and permeability variations in the range of 4000 mD to 6200 mD. The results of calculations show that the sandstone sample in this research is highly porous and permeable. The method combined with rock physics can be powerful tools for determining rock properties from small rock fragments.

Seismic spectral decomposition and analysis based on Wigner–Ville distribution for sandstone reservoir characterization in West Sichuan depression

International Nuclear Information System (INIS)

Wu, Xiaoyang; Liu, Tianyou

2010-01-01

Reflections from a hydrocarbon-saturated zone are generally expected to have a tendency to be low frequency. Previous work has shown the application of seismic spectral decomposition for low-frequency shadow detection. In this paper, we further analyse the characteristics of spectral amplitude in fractured sandstone reservoirs with different fluid saturations using the Wigner–Ville distribution (WVD)-based method. We give a description of the geometric structure of cross-terms due to the bilinear nature of WVD and eliminate cross-terms using smoothed pseudo-WVD (SPWVD) with time- and frequency-independent Gaussian kernels as smoothing windows. SPWVD is finally applied to seismic data from West Sichuan depression. We focus our study on the comparison of SPWVD spectral amplitudes resulting from different fluid contents. It shows that prolific gas reservoirs feature higher peak spectral amplitude at higher peak frequency, which attenuate faster than low-quality gas reservoirs and dry or wet reservoirs. This can be regarded as a spectral attenuation signature for future exploration in the study area

Rate type isotach compaction of consolidated sandstone

NARCIS (Netherlands)

Waal, J.A. de; Thienen-Visser, K. van; Pruiksma, J.P.

2015-01-01

Laboratory experiments on samples from a consolidated sandstone reservoir are presented that demonstrate rate type compaction behaviour similar to that observed on unconsolidated sands and soils. Such rate type behaviour can have large consequences for reservoir compaction, surface subsidence and

Sandstone-filled normal faults: A case study from central California

Science.gov (United States)

Palladino, Giuseppe; Alsop, G. Ian; Grippa, Antonio; Zvirtes, Gustavo; Phillip, Ruy Paulo; Hurst, Andrew

2018-05-01

Despite the potential of sandstone-filled normal faults to significantly influence fluid transmissivity within reservoirs and the shallow crust, they have to date been largely overlooked. Fluidized sand, forcefully intruded along normal fault zones, markedly enhances the transmissivity of faults and, in general, the connectivity between otherwise unconnected reservoirs. Here, we provide a detailed outcrop description and interpretation of sandstone-filled normal faults from different stratigraphic units in central California. Such faults commonly show limited fault throw, cm to dm wide apertures, poorly-developed fault zones and full or partial sand infill. Based on these features and inferences regarding their origin, we propose a general classification that defines two main types of sandstone-filled normal faults. Type 1 form as a consequence of the hydraulic failure of the host strata above a poorly-consolidated sandstone following a significant, rapid increase of pore fluid over-pressure. Type 2 sandstone-filled normal faults form as a result of regional tectonic deformation. These structures may play a significant role in the connectivity of siliciclastic reservoirs, and may therefore be crucial not just for investigation of basin evolution but also in hydrocarbon exploration.

Freshwater reservoir effect variability in Northern Germany

DEFF Research Database (Denmark)

Philippsen, B.; Heinemeier, J.

2013-01-01

The freshwater reservoir effect is a potential problem when radiocarbon dating fish bones, shells, human bones, or food crusts on pottery from sites near rivers or lakes. The reservoir age in hardwater rivers can be up to several thousand years and may be highly variable. Accurate 14C dating of f...... that can also be expected for the past. This knowledge will be applied to the dating of food crusts on pottery from the Mesolithic sites Kayhude at the Alster River and Schlamersdorf at the Trave River, both in Schleswig-Holstein, northern Germany....

Freshwater reservoir effect variability in Northern Germany

DEFF Research Database (Denmark)

Philippsen, Bente; Heinemeier, Jan

2012-01-01

Kayhude at the river Alster and Schlamersdorf at the river Trave, both in Schleswig-Holstein, Northern Germany. Measurements on modern materials from these rivers may not give a single reservoir age correction that can be applied to archaeological samples, but they will show the order of magnitude...

Anomalies of natural gas compositions and carbon isotope ratios caused by gas diffusion - A case from the Donghe Sandstone reservoir in the Hadexun Oilfield, Tarim Basin, northwest China

Science.gov (United States)

Wang, Yangyang; Chen, Jianfa; Pang, Xiongqi; Zhang, Baoshou; Wang, Yifan; He, Liwen; Chen, Zeya; Zhang, Guoqiang

2018-05-01

Natural gases in the Carboniferous Donghe Sandstone reservoir within the Block HD4 of the Hadexun Oilfield, Tarim Basin are characterized by abnormally low total hydrocarbon gas contents ( δ13C ethane (C2) gas has never been reported previously in the Tarim Basin and such large variations in δ13C have rarely been observed in other basins globally. Based on a comprehensive analysis of gas geochemical data and the geological setting of the Carboniferous reservoirs in the Hadexun Oilfield, we reveal that the anomalies of the gas compositions and carbon isotope ratios in the Donghe Sandstone reservoir are caused by gas diffusion through the poorly-sealed caprock rather than by pathways such as gas mixing, microorganism degradation, different kerogen types or thermal maturity degrees of source rocks. The documentation of an in-reservoir gas diffusion during the post entrapment process as a major cause for gas geochemical anomalies may offer important insight into exploring natural gas resources in deeply buried sedimentary basins.

Effective Wettability Measurements of CO2-Brine-Sandstone System at Different Reservoir Conditions

Science.gov (United States)

Al-Menhali, Ali; Krevor, Samuel

2014-05-01

, core-scale effective contact angle can be determined. In addition to providing a quantitative measure of the core-averaged wetting properties, the technique allows for the observation of shifts in contact angle with changing conditions. We examine the wettability changes of the CO2-brine system in Berea sandstone with variations in reservoir conditions including supercritical, gaseous and liquid CO2injection. We evaluate wettability variation within a single rock with temperature, pressure, and salinity across a range of conditions relevant to subsurface CO2 storage. This study will include results of measurements in a Berea sandstone sample across a wide range of conditions representative of subsurface reservoirs suitable for CO2 storage (5-20 MPa, 25-90 oC, 0-5 mol kg-1). The measurement uses X-ray CT imaging in a state of the art core flooding laboratory designed to operate at high temperature, pressure, and concentrated brines.

Diagenetic Evolution and Reservoir Quality of Sandstones in the North Alpine Foreland Basin: A Microscale Approach.

Science.gov (United States)

Gross, Doris; Grundtner, Marie-Louise; Misch, David; Riedl, Martin; Sachsenhofer, Reinhard F; Scheucher, Lorenz

2015-10-01

Siliciclastic reservoir rocks of the North Alpine Foreland Basin were studied focusing on investigations of pore fillings. Conventional oil and gas production requires certain thresholds of porosity and permeability. These parameters are controlled by the size and shape of grains and diagenetic processes like compaction, dissolution, and precipitation of mineral phases. In an attempt to estimate the impact of these factors, conventional microscopy, high resolution scanning electron microscopy, and wavelength dispersive element mapping were applied. Rock types were established accordingly, considering Poro/Perm data. Reservoir properties in shallow marine Cenomanian sandstones are mainly controlled by the degree of diagenetic calcite precipitation, Turonian rocks are characterized by reduced permeability, even for weakly cemented layers, due to higher matrix content as a result of lower depositional energy. Eocene subarkoses tend to be coarse-grained with minor matrix content as a result of their fluvio-deltaic and coastal deposition. Reservoir quality is therefore controlled by diagenetic clay and minor calcite cementation.Although Eocene rocks are often matrix free, occasionally a clay mineral matrix may be present and influence cementation of pores during early diagenesis. Oligo-/Miocene deep marine rocks exhibit excellent quality in cases when early cement is dissolved and not replaced by secondary calcite, mainly bound to the gas-water contact within hydrocarbon reservoirs.

Imaging fluid/solid interactions in hydrocarbon reservoir rocks.

Science.gov (United States)

Uwins, P J; Baker, J C; Mackinnon, I D

1993-08-01

The environmental scanning electron microscope (ESEM) has been used to image liquid hydrocarbons in sandstones and oil shales. Additionally, the fluid sensitivity of selected clay minerals in hydrocarbon reservoirs was assessed via three case studies: HCl acid sensitivity of authigenic chlorite in sandstone reservoirs, freshwater sensitivity of authigenic illite/smectite in sandstone reservoirs, and bleach sensitivity of a volcanic reservoir containing abundant secondary chlorite/corrensite. The results showed the suitability of using ESEM for imaging liquid hydrocarbon films in hydrocarbon reservoirs and the importance of simulating in situ fluid-rock interactions for hydrocarbon production programmes. In each case, results of the ESEM studies greatly enhanced prediction of reservoir/borehole reactions and, in some cases, contradicted conventional wisdom regarding the outcome of potential engineering solutions.

Geohydrology of the Navajo sandstone in western Kane, southwestern Garfield, and southeastern Iron counties, Utah

Science.gov (United States)

Freethey, G.W.

1988-01-01

The upper Navajo and Lamb Point aquifers in the Navajo Sandstone are the principal source of water for the city of Kanab, irrigation, stock, and for rural homes in the study area. Well logs and outcrop descriptions indicate the Navajo Sandstone consists of the Lamb Point Tongue and an unnamed upper member that are separated by the Tenney Canyon Tongue of the Kayenta Formation. The main Kayenta Formation underlies the Lamb Point Tongue. The Lamb Point Tongue and the upper member of the Navajo Sandstone are saturated and hydraulically connected through the Tenney Canyon Tongue. Available data indicate that precipitation percolates to the groundwater reservoir where the Navajo Sandstone crops out. Estimates of the rate of recharge at the outcrop range from 0.1 to as much as 2.8 in/yr. Water level data indicate that water moves from the upper member of the Navajo Sandstone, through the Tenney Canyon Tongue, and into the Lamb Point Tongue. Lateral flow is generally from the outcrop areas toward the incised canyons formed by tributaries of Kanab Creek and Johnson Wash. Direction and rate of groundwater movement and the location and character of the natural hydrologic boundaries in the northern part of the area where the Navajo Sandstone is buried cannot be determined conclusively without additional water level data. (Author 's abstract)

Methane in the Northern West Siberian Basin. Generation, dynamics of the reservoirs and exchange with the atmosphere

International Nuclear Information System (INIS)

Cramer, B.

1997-07-01

Based on compositional data and isotope geochemistry natural gas in northern West Siberia can be divided into three groups. These are: natural gas in Jurassic rocks, natural gas in Neocomian rocks and natural gas from the Aptian to Cenomanian Pokur Formation. Natural gas in Jurassic rocks was generated thermogenically from rocks of the Jurassic Tyumen Formation. Natural gas in Neocomian rocks is also of thermogenic origin, possibly being generated from the organic matter of Lower Cretaceous sediments. The largest accumulation of natural gas occurs in sandstone reservoirs in the Pokur Formation. This gas can be described as a mixture between thermogenic gas from deeper strata and isotopically light almost pure methane. 98.6% of this gas consists of methane with an unusual isotope signature of -51.2 permille. It is not possible to explain the existence of this methane with established concepts of gas generation. A new model was developed to examine the possibility of a thermogenic origin of the isotopically light methane in early mature rocks of the Pokur Formation. Based on pyrolysis experiments and reaction kinetic calculations the model enables the simulation of stable carbon isotope ratios of hydrocarbon components in natural gas. The temperature dependent kinetic isotope fractionation is defined by a difference in the activation energies of 12 C-and 13 C-methane generation. The application of the new method to two coaly sandstones of the Pokur Formation results in a good correspondence between modelled carbon isotope ratios of δ 13 C values of methane in the reservoirs. The mass of methane thermogenically generated within the Pokur Formation under the gas field structures, however, is not sufficient to explain the mass of accumulated methane. (orig./SR) [de

Flow units classification for geostatisitical three-dimensional modeling of a non-marine sandstone reservoir: A case study from the Paleocene Funing Formation of the Gaoji Oilfield, east China

Science.gov (United States)

Zhang, Penghui; Zhang, Jinliang; Wang, Jinkai; Li, Ming; Liang, Jie; Wu, Yingli

2018-05-01

Flow units classification can be used in reservoir characterization. In addition, characterizing the reservoir interval into flow units is an effective way to simulate the reservoir. Paraflow units (PFUs), the second level of flow units, are used to estimate the spatial distribution of continental clastic reservoirs at the detailed reservoir description stage. In this study, we investigate a nonroutine methodology to predict the external and internal distribution of PFUs. The methodology outlined enables the classification of PFUs using sandstone core samples and log data. The relationships obtained between porosity, permeability and pore throat aperture radii (r35) values were established for core and log data obtained from 26 wells from the Funing Formation, Gaoji Oilfield, Subei Basin, China. The present study refines predicted PFUs at logged (0.125-m) intervals, whose scale is much smaller than routine methods. Meanwhile, three-dimensional models are built using sequential indicator simulation to characterize PFUs in wells. Four distinct PFUs are classified and located based on the statistical methodology of cluster analysis, and each PFU has different seepage ability. The results of this study demonstrate the obtained models are able to quantify reservoir heterogeneity. Due to different petrophysical characteristics and seepage ability, PFUs have a significant impact on the distribution of the remaining oil. Considering these allows a more accurate understanding of reservoir quality, especially within non-marine sandstone reservoirs.

Diagenesis and reservoir quality evolution of palaeocene deep-water, marine sandstones, the Shetland-Faroes Basin, British continental shelf

Energy Technology Data Exchange (ETDEWEB)

Mansurbeg, H. [Department of Earth Sciences, Uppsala University, Villavaegen 16, SE 752 36 Uppsala (Sweden); Morad, S. [Department of Earth Sciences, Uppsala University, Villavaegen 16, SE 752 36 Uppsala (Sweden); Department of Petroleum Geosciences, The Petroleum Institute, P.O. Box 2533, Abu Dhabi (United Arab Emirates); Salem, A. [Faculty of Education at Kafr El-Sheikh, Tanta University, Kafr El-Sheikh (Egypt); Marfil, R.; Caja, M.A. [Departmento Petrologia y Geoquimica, Facultad de Geologia, UCM, 28040 Madrid (Spain); El-ghali, M.A.K. (Geology Department, Al-Fateh University, P.O. Box 13696, Libya); Nystuen, J.P. [Department of Geosciences, University of Oslo, P.O. Box 1047 Blindern, NO-0316 Oslo (Norway); Amorosi, A. [Department of Earth Sciences, University of Bologna, Via Zamboni 67, 40127 Bologna (Italy); Garcia, D. [Centre SPIN, Department GENERIC, Ecole Nationale Superieure des Mines de Saint Etienne 158, Cours Fauriel 42023, Saint-Etienne (France); La Iglesia, A. [Instituto de Geologia Economica (CSIC-UCM), Facultad de Geologia, UCM, 28040 Madrid (Spain)

2008-06-15

The Palaeocene, deep-water marine sandstones recovered from six wells in the Shetland-Faroes Basin represent lowstand, transgressive and highstand systems tract turbiditic sediments. Mineralogic, petrographic, and geochemical analyses of these siliciclastics are used to decipher and discuss the diagenetic alterations and subsequent reservoir quality evolution. The Middle-Upper Palaeocene sandstones (subarkoses to arkoses) from the Shetland-Faroes Basin, British continental shelf are submarine turbiditic deposits that are cemented predominantly by carbonates, quartz and clay minerals. Carbonate cements (intergranular and grain replacive calcite, siderite, ferroan dolomite and ankerite) are of eogenetic and mesogenetic origins. The eogenetic alterations have been mediated by marine, meteoric and mixed marine/meteoric porewaters and resulted mainly in the precipitation of calcite ({delta}{sup 18}O{sub V-PDB}=-10.9 permille and -3.8 permille), trace amounts of non-ferroan dolomite, siderite ({delta}{sup 18}O{sub V-PDB}=-14.4 permille to -0.6 permille), as well as smectite and kaolinite in the lowstand systems tract (LST) and highstand systems tract (HST) turbiditic sandstone below the sequence boundary. Minor eogenetic siderite has precipitated between expanded and kaolinitized micas, primarily biotite. The mesogenetic alterations are interpreted to have been mediated by evolved marine porewaters and resulted in the precipitation of calcite ({delta}{sup 18}O{sub V-PDB}=-12.9 permille to -7.8 permille) and Fe-dolomite/ankerite ({delta}{sup 18}O{sub V-PDB}=-12.1 permille to -6.3 permille) at temperatures of 50-140 and 60-140 C, respectively. Quartz overgrowths and outgrowth, which post- and pre-date the mesogenetic carbonate cements is more common in the LST and TST of distal turbiditic sandstone. Discrete quartz cement, which is closely associated with illite and chlorite, is the final diagenetic phase. The clay minerals include intergranular and grain replacive

Determination of residual oil saturation from time-lapse pulsed neutron capture logs in a large sandstone reservoir

International Nuclear Information System (INIS)

Syed, E.V.; Salaita, G.N.; McCaffery, F.G.

1991-01-01

Cased hole logging with pulsed neutron tools finds extensive use for identifying zones of water breakthrough and monitoring oil-water contacts in oil reservoirs being depleted by waterflooding or natural water drive. Results of such surveys then find direct use for planning recompletions and water shutoff treatments. Pulsed neutron capture (PNC) logs are useful for estimating water saturation changes behind casing in the presence of a constant, high-salinity environment. PNC log surveys run at different times, i.e., in a time-lapse mode, are particularly amenable to quantitative analysis. The combined use of the original open hole and PNC time-lapse log information can then provide information on remaining or residual oil saturations in a reservoir. This paper reports analyses of historical pulsed neutron capture log data to assess residual oil saturation in naturally water-swept zones for selected wells from a large sandstone reservoir in the Middle East. Quantitative determination of oil saturations was aided by PNC log information obtained from a series of tests conducted in a new well in the same field

Asymmetrical cross-current turbidite facies tract in a structurally-confined mini-basin (Priabonian-Rupelian, Ranzano Sandstone, northern Apennines, Italy)

NARCIS (Netherlands)

Tinterri, R.; Laporta, M.; Ogata, K.

2017-01-01

This work discusses the stratigraphy and facies analysis of the Ranzano Sandstone, in the northern Apennines (Italy), a confined low-efficiency turbidite system deposited in a series of small piggy-back basins, which show strong analogies with intraslope minibasins commonly observed in divergent

Wettability Alteration of Sandstone and Carbonate Rocks by Using ZnO Nanoparticles in Heavy Oil Reservoirs

Directory of Open Access Journals (Sweden)

Masoumeh Tajmiri

2015-10-01

Full Text Available Efforts to enhance oil recovery through wettability alteration by nanoparticles have been attracted in recent years. However, many basic questions have been ambiguous up until now. Nanoparticles penetrate into pore volume of porous media, stick on the core surface, and by creating homogeneous water-wet area, cause to alter wettability. This work introduces the new concept of adding ZnO nanoparticles by an experimental work on wettability alteration and oil recovery through spontaneous imbibition mechanism. Laboratory tests were conducted in two experimental steps on four cylindrical core samples (three sandstones and one carbonate taken from a real Iranian heavy oil reservoir in Amott cell. In the first step, the core samples were saturated by crude oil. Next, the core samples were flooded with nanoparticles and saturated by crude oil for about two weeks. Then, the core samples were immersed in distilled water and the amount of recovery was monitored during 30 days for both steps. The experimental results showed that oil recovery for three sandstone cores changed from 20.74, 4.3, and 3.5% of original oil in place (OOIP in the absence of nanoparticles to 36.2, 17.57, and 20.68% of OOIP when nanoparticles were added respectively. Moreover, for the carbonate core, the recovery changed from zero to 8.89% of OOIP by adding nanoparticles. By the investigation of relative permeability curves, it was found that by adding ZnO nanoparticles, the crossover-point of curves shifted to the right for both sandstone and carbonate cores, which meant wettability was altered to water- wet. This study, for the first time, illustrated the remarkable role of ZnO nanoparticles in wettability alteration toward more water-wet for both sandstone and carbonate cores and enhancing oil recovery.

The Collyhurst Sandstone as a secondary storage unit for CCS in the East Irish Sea Basin (UK)

Science.gov (United States)

Gamboa, D.; Williams, J. D. O.; Kirk, K.; Gent, C. M. A.; Bentham, M.; Schofield, D. I.

2016-12-01

Carbon Capture and Storage (CCS) is key technology for low-carbon energy and industry. The UK hosts a large CO2 storage potential offshore with an estimated capacity of 78 Gt. The East Irish Sea Basin (EISB) is the key area for CCS in the western UK, with a CO2 storage potential of 1.7 Gt in hydrocarbon fields and in saline aquifers within the Triassic Sherwood Sandstone Formation. However, this theoretical storage capacity does not consider the secondary storage potential in the lower Permian Collyhurst Sandstone Formation. 3D seismic data were used to characterise the Collyhurst Sandstone Formation in the EISB. On the southern basin domain, numerous fault-bound blocks limit the lateral continuity of the sandstone strata, while on the northern domain the sandstones are intersected by less faults. The caprock for the Collyhurst sandstones is variable. The Manchester Marls predominate in the south, transitioning to the St. Bees evaporites towards the north. The evaporites in the EISB cause overburden faults to terminate or detach along Upper Permian strata, limiting the deformation of the underlying reservoir units. Five main storage closures have been identified in the Permian strata. In the southern and central area these are predominantly fault bounded, occurring at depths over 1000m. Despite the higher Collyhurst sandstone thickness in the southern IESB, the dolomitic nature of the caprock constitutes a storage risk in this area. Closures in the northern area are deeper (around 2000-2500m) and wider, reaching areas of 34Km2, and are overlain by evaporitic caprocks. The larger Collyhurst closures to the north underlie large Triassic fields with high storage potential. The spatial overlap favours storage plans including secondary storage units in the EISB. The results of this work also expand the understanding of prospective areas for CO2 sequestration in the East Irish Sea Basin in locations where the primary Sherwood Sandstone Formation is either too shallow

Sedimentary uranium occurrences in Eastern Europe with special reference to sandstone formations

International Nuclear Information System (INIS)

Barthel, F.; Hahn, L.

1985-01-01

Sedimentary uranium deposits, especially in sandstones, play an important role in uranium mining in Eastern Europe. The paper reviews recent publications on uranium occurrences in sandstone formations in the German Democratic Republic, Poland, CSSR, Hungary, Romania, Bulgaria and Albania. The uranium deposits in sandstones in Yugoslavia are described in a separate paper in this volume. Sandstone deposits of the USSR are not reviewed. Uranium mineralizations occur in sandstones from Ordovician to Tertiary age. Major deposits are developed in Upper Carboniferous sandstones in association with coal (GDR, Poland), in Permian strata (CSSR, Hungary, Romania), in Cretaceous sandstones (GDR, CSSR), and in Tertiary sediments (CSSR). The Permian deposits can be compared with deposits of similar age in Northern Italy and Northern Yugoslavia. Roll-type orebodies are developed in some of the Cenomanian sandstones. Tertiary deposits are mainly associated with lignites. Uranium deposits in sandstones of Albania and Bulgaria are not described in the literature. Geologic similarities with sandstone basins in adjacent countries suggest the presence of uranium mineralizations in Permian, Lower Triassic, and Tertiary sandstones. (author)

Mesozoic-Cenozoic tectonic evolution and its relation to sandstone-type uranium mineralization in northern Tarim area--Evidence from apatite fission track

International Nuclear Information System (INIS)

Liu Hongxu; Dong Wenming; Liu Zhangyue; Chen Xiaolin

2009-01-01

The apatite fission track dating and inversion result of geological thermal history of four rock specimens from Sawafuqi area and Talike area in northern Tarim Basin show that two areas uplifted at different ages. The apatite fission track ages of Sawafuqi range from 3.5 to 3.9 Ma, while the ages of Talike range from 53 to 59 Ma. The thermal history recorded by rock samples reveals that there are at least three prominent cooling phases since Late Cretaceous epoch. Detailed study was made on the division of uplifting stages during Mesozoic and Cenozoic tectonic evolution with the existing data in northern Tarim area. And new ideas on tectonic evolution and sandstone-type uranium mineralization have been put forward by combining with the sandstone-type uranium mineralization ages in this area.(authors)

Ephemeral-fluvial sediments as potential hydrocarbon reservoirs. Vol. 1: Sedimentology

Energy Technology Data Exchange (ETDEWEB)

Taylor, K.S.

1994-12-31

Although reservoirs formed from ephemeral-fluvial sandstones have previously been considered relatively simple, unresolved problems of sandbody correlation and production anomalies demonstrate the need for improved understanding of their internal complexity. Outcropping ephemeral-fluvial systems have been studied in order to determine the main features and processes occurring in sand-rich ephemeral systems and to identify which features will be of importance in a hydrocarbon reservoir. The Lower Jurassic Upper Moenave and Kayenta Formations of south-eastern Utah and northern Arizona comprise series of stacked, sand-dominated sheet-like palaeochannels suggestive of low sinuosity, braided systems. Low subsidence rates and rapid lateral migration rates enabled channels to significantly modify their widths during high discharge. (author)

Mechanical changes caused by CO2-driven cement dissolution in the Morrow B Sandstone at reservoir conditions: Experimental observations

Science.gov (United States)

Wu, Z.; Luhmann, A. J.; Rinehart, A. J.; Mozley, P.; Dewers, T. A.

2017-12-01

Carbon Capture, Utilization and Storage (CCUS) in transmissive reservoirs is a proposed mechanism in reducing CO2 emissions. Injection of CO2 perturbs reservoir chemistry, and can modify porosity and permeability and alter mineralogy. However, little work has been done on the coupling of rock alteration by CO2 injection and the mechanical integrity of the reservoir. In this study, we perform flow-through experiments on calcite- and dolomite-cemented Pennsylvanian Morrow B Sandstone (West Texas, USA) cores. We hypothesize that poikilotopic calcite cement has a larger impact on chemo-mechanical alteration than disseminated dolomite cement given similar CO2 exposure. With one control brine flow-through experiment and two CO2-plus-brine flow-through experiments for each cement composition, flow rates of 0.1 and 0.01 ml/min were applied under 4200 psi pore fluid pressure and 5000 psi confining pressure at 71 °C. Fluid chemistry and permeability data enable monitoring of mineral dissolution. Ultrasonic velocities were measured pre-test using 1.2 MHz source-receiver pairs at 0.5 MPa axial load and show calcite-cemented samples with higher dynamic elastic moduli than dolomite-cemented samples. Velocities measured post-experiment will identify changes from fluid-rock interaction. We plan to conduct cylinder-splitting destructive mechanical test (Brazil test) to measure the pristine and altered tensile strength of different cemented sandstones. The experiments will identify extents to which cement composition and texture control chemo-mechanical degradation of CCUS reservoirs. Funding for this project is provided by the U.S. Department of Energy's (DOE) National Energy Technology Laboratory (NETL) through the Southwest Regional Partnership on Carbon Sequestration (SWP) under Award No. DE-FC26-05NT42591. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of

Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin)

Energy Technology Data Exchange (ETDEWEB)

Andrew G. Cole; George B. Asquith; Jose I. Guzman; Mark D. Barton; Mohammad A. Malik; Shirley P. Dutton; Sigrid J. Clift

1998-04-01

The objective of this Class III project is to demonstrate that detailed reservoir characterization of clastic reservoirs in basinal sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover more of the original oil in place by strategic infill-well placement and geologically based enhanced oil recovery. The study focused on the Ford Geraldine unit, which produces from the upper Bell Canyon Formation (Ramsey sandstone). Reservoirs in this and other Delaware Mountain Group fields have low producibility (average recovery <14 percent of the original oil in place) because of a high degree of vertical and lateral heterogeneity caused by depositional processes and post-depositional diagenetic modification. Outcrop analogs were studied to better interpret the depositional processes that formed the reservoirs at the Ford Geraldine unit and to determine the dimensions of reservoir sandstone bodies. Facies relationships and bedding architecture within a single genetic unit exposed in outcrop in Culberson County, Texas, suggest that the sandstones were deposited in a system of channels and levees with attached lobes that initially prograded basinward, aggraded, and then turned around and stepped back toward the shelf. Channel sandstones are 10 to 60 ft thick and 300 to 3,000 ft wide. The flanking levees have a wedge-shaped geometry and are composed of interbedded sandstone and siltstone; thickness varies from 3 to 20 ft and length from several hundred to several thousands of feet. The lobe sandstones are broad lens-shaped bodies; thicknesses range up to 30 ft with aspect ratios (width/thickness) of 100 to 10,000. Lobe sandstones may be interstratified with laminated siltstones.

Composition of natural gas and crude oil produced from 10 wells in the Lower Silurian "Clinton" Sandstone, Trumbull County, Ohio: Chapter G.7 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Burruss, Robert A.; Ryder, Robert T.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

Natural gases and associated crude oils in the “Clinton” sandstone, Medina Group sandstones, and equivalent Tuscarora Sandstone in the northern Appalachian basin are part of a regional, continuous-type or basin-centered accumulation. The origin of the hydrocarbon charge to regional continuoustype accumulations is poorly understood. We have analyzed the molecular and stable isotopic composition of gases and oils produced from 10 wells in the “Clinton” sandstone in Trumbull County, Ohio, in an initial attempt to identify the characteristics of the accumulated fluids. The analyses show that the fluids have remarkably uniform compositions that are similar to previously published analyses of oils (Cole and others, 1987) and gases (Laughrey and Baldasarre, 1998) in Early Silurian reservoirs elsewhere in Ohio; however, geochemical parameters in the oils and gases suggest that the fluids have experienced higher levels of thermal stress than the present-day burial conditions of the reservoir rocks. The crude oils have an unusual geochemical characteristic: they do not contain detectable levels of sterane and triterpane biomarkers. The origin of these absences is unknown.

Controls on the quality of Miocene reservoirs, southern Gulf of Mexico

Science.gov (United States)

Gutiérrez Paredes, Hilda Clarisa; Catuneanu, Octavian; Hernández Romano, Ulises

2018-01-01

An investigation was conducted to determine the main controls on the reservoir quality of the middle and upper Miocene sandstones in the southern Gulf of Mexico based on core descriptions, thin section petrography and petrophysical data; as well as to explore the possible link between the sequence stratigraphic framework, depositional facies and diagenetic alterations. The Miocene deep marine sandstones are attributed to the falling-stage, lowstand, and transgressive systems tracts. The middle Miocene falling-stage systems tract includes medium-to very fine-grained, and structureless sandstones deposited in channels and frontal splays, and muddy sandstones, deposited in lobes of debrites. The lowstand and transgressive systems tracts consist of medium-to very fine-grained massive and normally graded sandstones deposited in channel systems within frontal splay complexes. The upper Miocene falling-stage systems tract includes medium-to coarse-grained, structureless sandstones deposited in channel systems and frontal splay, as well as lobes of debrites formed by grain flows and hybrid-flow deposits. The lowstand and transgressive systems tracts include fine-grained sandstones deposited in overbank deposits. The results reveal that the depositional elements with the best reservoir quality are the frontal splays deposited during the falling-stage system tracts. The reservoir quality of the Miocene sandstones was controlled by a combination of depositional facies, sand composition and diagenetic factors (mainly compaction and calcite cementation). Sandstone texture, controlled primarily by depositional facies appears more important than sandstone composition in determining reservoir quality; and compaction was more important than cementation in porosity destruction. Compaction was stopped, when complete calcite cementation occurred.

Provenance of the Lower Triassic Bunter Sandstone Formation: implications for distribution and architecture of aeolian vs. fluvial reservoirs in the North German Basin

DEFF Research Database (Denmark)

Olivarius, Mette; Weibel, Rikke; Friis, Henrik

2017-01-01

Zircon U–Pb geochronometry, heavy mineral analyses and conventional seismic reflection data were used to interpret the provenance of the Lower Triassic Bunter Sandstone Formation. The succession was sampled in five Danish wells in the northern part of the North German Basin. The results show...... Shield did not supply much sediment to the basin as opposed to what was previously believed. Sediment from the Variscan belt was transported by wind activity across the North German Basin when it was dried out during deposition of the aeolian part of the Volpriehausen Member (lower Bunter Sandstone......). Fluvial sand was supplied from the Ringkøbing-Fyn High to the basin during precipitation events which occurred most frequently when the Solling Member was deposited (upper Bunter Sandstone). Late Neoproterozoic to Carboniferous zircon ages predominate in the Volpriehausen Member where the dominant age...

Effect of temperature on sandstone permeability

DEFF Research Database (Denmark)

Rosenbrand, Esther; Kjøller, Claus

Hot water injection in geothermal sandstone aquifers is considered for seasonal energy storage in Denmark. However, an increase in the aquifer temperature might reduce permeability, and thereby increase production costs. An understanding of the factors that control permeability is required in order...... and the Klinkenberg procedure showed the expected correlation between the two measures, however, differences could be around one order of magnitude. In tight gas sandstones, permeability is often sensitive to net stress, which might change due to the pore pressure change in the Klinkenberg procedure. Besides...... affecting the Klinkenberg procedure, the combined effect of slip and changes in permeability would affect production during pressure depletion in tight gas sandstone reservoirs; therefore effects of gas slip and net stress on permeability were combined in a model based on the Klinkenberg equation. A lower...

Application of advanced reservoir characterization, simulation and production optimization strategies to maximize recovery in slope and basin clastic reservoirs, West Texas (Delaware Basin). Annual report

Energy Technology Data Exchange (ETDEWEB)

Dutton, S.P.; Asquith, G.B.; Barton, M.D.; Cole, A.G.; Gogas, J.; Malik, M.A.; Clift, S.J.; Guzman, J.I.

1997-11-01

The objective of this project is to demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover a higher percentage of the original oil in place through strategic placement of infill wells and geologically based field development. This project involves reservoir characterization of two Late Permian slope and basin clastic reservoirs in the Delaware Basin, West Texas, followed by a field demonstration in one of the fields. The fields being investigated are Geraldine Ford and Ford West fields in Reeves and Culberson Counties, Texas. Project objectives are divided into two major phases, reservoir characterization and implementation. The objectives of the reservoir characterization phase of the project were to provide a detailed understanding of the architecture and heterogeneity of the two fields, the Ford Geraldine unit and Ford West field. Reservoir characterization utilized 3-D seismic data, high-resolution sequence stratigraphy, subsurface field studies, outcrop characterization, and other techniques. Once reservoir characterized was completed, a pilot area of approximately 1 mi{sup 2} at the northern end of the Ford Geraldine unit was chosen for reservoir simulation. This report summarizes the results of the second year of reservoir characterization.

The Bentheim Sandstone: Geology, petrophysics, varieties and it's use as dimension stone

NARCIS (Netherlands)

Dubelaar, C.W.; Nijland, T.G.

2014-01-01

The shallow-marine Bentheim Sandstone was deposited in one of the NW-SE trending basins north of the London-Brabant and Rhenish massifs during the Valanginian (Early Cretaceous). The Bentheim Sandstone forms an important reservoir rock for petroleum, but has also proven itself as a very durable

The experimental modeling of gas percolation mechanisms in a coal-measure tight sandstone reservoir: A case study on the coal-measure tight sandstone gas in the Upper Triassic Xujiahe Formation, Sichuan Basin, China

Directory of Open Access Journals (Sweden)

Shizhen Tao

2016-12-01

Full Text Available Tight sandstone gas from coal-measure source rock is widespread in China, and it is represented by the Xujiahe Formation of the Sichuan Basin and the Upper Paleozoic of the Ordos Basin. It is affected by planar evaporative hydrocarbon expulsion of coal-measure source rock and the gentle structural background; hydrodynamics and buoyancy play a limited role in the gas migration-accumulation in tight sandstone. Under the conditions of low permeability and speed, non-Darcy flow is quite apparent, it gives rise to gas-water mixed gas zone. In the gas displacing water experiment, the shape of percolation flow curve is mainly influenced by core permeability. The lower the permeability, the higher the starting pressure gradient as well as the more evident the non-Darcy phenomenon will be. In the gas displacing water experiment of tight sandstone, the maximum gas saturation of the core is generally less than 50% (ranging from 30% to 40% and averaging at 38%; it is similar to the actual gas saturation of the gas zone in the subsurface core. The gas saturation and permeability of the core have a logarithm correlation with a correlation coefficient of 0.8915. In the single-phase flow of tight sandstone gas, low-velocity non-Darcy percolation is apparent; the initial flow velocity (Vd exists due to the slippage effect of gas flow. The shape of percolation flow curve of a single-phase gas is primarily controlled by core permeability and confining pressure; the lower the permeability or the higher the confining pressure, the higher the starting pressure (0.02–0.08 MPa/cm, whereas, the higher the quasi-initial flow speed, the longer the nonlinear section and the more obvious the non-Darcy flow will be. The tight sandstone gas seepage mechanism study shows that the lower the reservoir permeability, the higher the starting pressure and the slower the flow velocity will be, this results in the low efficiency of natural gas migration and accumulation as well as

Impacts of Northern Pike on stocked Rainbow Trout in Pactola Reservoir, South Dakota

Science.gov (United States)

Scheibel, Natalie C.; Dembkowski, Daniel J.; Davis, Jacob L.; Chipps, Steven R.

2016-01-01

Establishment of nonnative Northern Pike Esox lucius in Pactola Reservoir, South Dakota, has prompted concern among biologists about the influence of this species on the lake’s intensively managed salmonid fisheries. Ancedotal information suggests that catch rates of Rainbow Trout Oncorhynchus mykiss have declined while mean size and abundance of Northern Pike has increased, although quantitative information on diet and growth of the Northern Pike population is lacking. To address potential interactions between Northern Pike and Rainbow Trout, we assessed size-dependent predation by Northern Pike on Rainbow Trout and determined the relative energetic contribution of stocked Rainbow Trout to Northern Pike growth using bioenergetics modeling. Stable isotopes combined with traditional diet analyses revealed that smaller Northern Pike (Trout contributed less than 10% to their annual energy consumption. In contrast, larger Northern Pike (≥600 mm TL) consumed primarily Rainbow Trout, which accounted for 56% of their annual energy consumption. Combining estimates of Northern Pike predation with production costs of catchable-size Rainbow Trout revealed that annual economic losses ranged from US$15,259 to $24,801 per year. Over its lifespan, an age-10 Northern Pike was estimated to consume ~117 Rainbow Trout worth approximately $340. Thus, Northern Pike predation substantially influences salmonid management initiatives and is likely a primary factor contributing to reduced Rainbow Trout abundance and return to anglers in Pactola Reservoir. Strategies for reducing Northern Pike predation on Rainbow Trout include increasing the size of stocked fish or altering the timing and spatial distribution of stocking events.

Reservoir compartmentalization and management strategies: Lessons learned in the Illinois basin

Energy Technology Data Exchange (ETDEWEB)

Grube, J.P.; Crockett, J.E.; Huff, B.G. [and others

1997-08-01

A research project jointly sponsored by the US Department of Energy and the Illinois State Geological Survey focused on the Cypress and Aux Vases Formations (Mississippian), major clastic reservoirs in the Illinois Basin. Results from the research showed that understanding the nature and distribution of reservoir compartments, and using effective reservoir management strategies, can significantly improve recovery efficiencies from oil fields in this mature basin. Compartments can be most effectively drained where they are geologically well defined and reservoir management practices are coordinated through unified, compartment-wide, development programs. Our studies showed that the Cypress and Aux Vases reservoirs contain lateral and vertical permeability barriers forming compartments that range in size from isolated, interlaminated sandstone and shale beds to sandstone bodies tens of feet in thickness and more than a mile in length. Stacked or shingled, genetically similar sandstone bodies are commonly separated by thin impermeable intervals that can be difficult to distinguish on logs and can, therefore, cause correlation problems, even between wells drilled on spacing of less than ten acres. Lateral separation of sandstone bodies causes similar problems. Reservoir compartmentalization reduces primary and particularly secondary recovery by trapping pockets of by-passed or banked oil. Compartments can be detected by comparing recovery factors of genetically similar sandstone bodies within a field; using packers to separate commingled intervals and analyzing fluid recoveries and pressures; making detailed core-to-log calibrations that identify compartment boundaries; and analyzing pressure data from waterflood programs.

The computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in Northern Xinjiang, China

Energy Technology Data Exchange (ETDEWEB)

Zhengbang, Wang; Mingkuan, Qin; Ruiquan, Zhao; Shenghuang, Tang [Beijing Research Inst. of Uranium Geology, CNNC (China); Baoqun, Wang; Shuangxing, Lin [Geo-prospecting Team No. 216, CNNC (China)

2001-08-01

The process of establishment of the model includes following steps: (1) Systematically studying a known typical in-situ leachable sandstone type uranium deposit--Deposit No. 512 in Yili basin, analyzing its controlling factors and establishing its metallogenetic model; (2) Establishing the metallogenetic models of this type of uranium deposit and uranium-bearing area on the basis of comparison study on the deposit No. 512 with the same type uranium deposits in the world; (3) Creating the computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in northern Xinjiang; (4) Determining the standards of giving a evaluation-mark for each controlling factor of in-situ leachable sandstone type uranium deposit and uranium-bearing area; (5) Evaluating uranium potential and prospect of the unknown objective target.

The computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in Northern Xinjiang, China

International Nuclear Information System (INIS)

Wang Zhengbang; Qin Mingkuan; Zhao Ruiquan; Tang Shenghuang; Wang Baoqun; Lin Shuangxing

2001-01-01

The process of establishment of the model includes following steps: (1) Systematically studying a known typical in-situ leachable sandstone type uranium deposit--Deposit No. 512 in Yili basin, analyzing its controlling factors and establishing its metallogenetic model; (2) Establishing the metallogenetic models of this type of uranium deposit and uranium-bearing area on the basis of comparison study on the deposit No. 512 with the same type uranium deposits in the world; (3) Creating the computerized semi-quantitative comprehensive identification-evaluation model for the large-sized in-situ leachable sandstone type uranium deposits in northern Xinjiang; (4) Determining the standards of giving a evaluation-mark for each controlling factor of in-situ leachable sandstone type uranium deposit and uranium-bearing area; (5) Evaluating uranium potential and prospect of the unknown objective target

Structural-Diagenetic Controls on Fracture Opening in Tight Gas Sandstone Reservoirs, Alberta Foothills

Science.gov (United States)

Ukar, Estibalitz; Eichhubl, Peter; Fall, Andras; Hooker, John

2013-04-01

relatively undeformed backlimb strata. Fracture apertures locally increase adjacent to reverse faults without an overall increase in fracture frequency. Fluid inclusion analyses of crack-seal quartz cement indicate both aqueous and methane-rich inclusions are present. Homogenization temperatures of two-phase inclusions indicate synkinematic fracture cement precipitation and fracture opening under conditions at or near maximum burial of 190-210°C in core samples, and 120-160°C in outcrop samples. In comparison with the fracture evolution in other, less deformed tight-gas sandstone reservoirs such as the Piceance and East Texas basins where fracture opening is primarily controlled by gas generation, gas charge, and pore fluid pressure, these results suggest a strong control of regional tectonic processes on fracture generation. In conjunction with timing and rate of gas charge, rates of fracture cement growth, and stratigraphic-lithological controls, these processes determine the overall distribution of open fractures in these reservoirs.

Characterizing gas shaly sandstone reservoirs using the magnetic resonance technology in the Anaco area, East Venezuela

Energy Technology Data Exchange (ETDEWEB)

Fam, Maged; August, Howard [Halliburton, Houston, TX (United States); Zambrano, Carlos; Rivero, Fidel [PDVSA Gas (Venezuela)

2008-07-01

With demand for natural gas on the rise every day, accounting for and booking every cubic foot of gas is becoming very important to operators exploiting natural gas reservoirs. The initial estimates of gas reserves are usually established through the use of petrophysical parameters normally based on wireline and/or LWD logs. Conventional logs, such as gamma ray, density, neutron, resistivity and sonic, are traditionally used to calculate these parameters. Sometimes, however, the use of such conventional logs may not be enough to provide a high degree of accuracy in determining these petrophysical parameters, which are critical to reserve estimates. Insufficient accuracy can be due to high complexities in the rock properties and/or a formation fluid distribution within the reservoir layers that is very difficult to characterize with conventional logs alone. The high degree of heterogeneity in the shaly sandstone rock properties of the Anaco area, East Venezuela, can be characterized by clean, high porosity, high permeability sands to very shaly, highly laminated, and low porosity rock. This wide variation in the reservoir properties may pose difficulties in identifying gas bearing zones which may affect the final gas reserves estimates in the area. The application of the magnetic resonance imaging (MRI) logging technology in the area, combined with the application of its latest acquisition and interpretation methods, has proven to be very adequate in detecting and quantifying gas zones as well as providing more realistic petrophysical parameters for better reserve estimates. This article demonstrates the effectiveness of applying the MRI logging technology to obtain improved petrophysical parameters that will help better characterize the shaly-sands of Anaco area gas reservoirs. This article also demonstrates the value of MRI in determining fluid types, including distinguishing between bound water and free water, as well as differentiating between gas and liquid

Cathodoluminescence investigations on quartz cement in the sandstones of Khabour Formation from Iraqi Kurdistan Region, Northern Iraq

Science.gov (United States)

Omer, Muhamed F.; Friis, Henrik

2014-03-01

The Ordovician deltaic to shallow marine Khabour Formation in Northern Iraq consists mainly of sandstone with minor siltstone and interbedded shale. The sandstones are pervasively cemented by quartz that resulted in very little preserved primary porosity. Cathodoluminescence and petrographic studies showed that the silica cementation occurred in five successive phases which can be distinguished by their luminescence pattern. The precipitations of two phases have predated the major compaction process while the other phases are younger. The successive phases represent a sequence of changes in silica supply which were classified as very early and early, derived from dissolved biogenic silica that precipitated as opal/microquartz, possibly pre-compactional and of non-luminescent quartz overgrowth type. This was followed by phases whose silica supply derived from pressure solution of quartz, dissolution of feldspar, and hydrothermal fluids related to major thrust fault event. These successive quartz cement phases showed an increase in luminescence and the development of complicated zonation pattern in late-stage quartz cementation.

Diagenesis and reservoir properties of Cretaceous-Lower Tertiary sandstones: the GANT-1 well, western Nuussuaq, central West Greenland

Energy Technology Data Exchange (ETDEWEB)

Kierkegaard, Thomas

1998-08-01

The main purpose of this study is to describe the diagenetic alterations occurring in the Cretaceous to Lower Paleocene sedimentary succession of the GANT-1 well, and to determine the diagenetic and detrital factors which control present porosity and permeability. The GANT-1 well is located on north-western Nuussuaq, central West Greenland. The West Greenland margin is a continental margin subdivided into linked basins where Cretaceous to Lower Tertiary and probably older sediments have been deposited. In the Nuussuaq area these sediments are overlain by a succession of Early Tertiary basaltic volcanic rocks which reaches a combined thickness of around 2-2.5 km. Although the reservoir properties of the sandstone intervals in the GANT-1 and GANE-1 wells are generally relatively poor, it is suggested that moderate to good properties may be found in certain intervals within the Maastrichtian-Paleocene succession. However, the reason for the locally enhanced reservoir properties in GANT-1 was not clarified by this study due to the lack of regional petrographical data. (EG) EFP-96. 41 refs., 3 maps

Implications of heterogeneous fracture distribution on reservoir quality; an analogue from the Torridon Group sandstone, Moine Thrust Belt, NW Scotland

Science.gov (United States)

Watkins, Hannah; Healy, David; Bond, Clare E.; Butler, Robert W. H.

2018-03-01

Understanding fracture network variation is fundamental in characterising fractured reservoirs. Simple relationships between fractures, stress and strain are commonly assumed in fold-thrust structures, inferring relatively homogeneous fracture patterns. In reality fractures are more complex, commonly appearing as heterogeneous networks at outcrop. We use the Achnashellach Culmination (NW Scotland) as an outcrop analogue to a folded tight sandstone reservoir in a thrust belt. We present fracture data is collected from four fold-thrust structures to determine how fracture connectivity, orientation, permeability anisotropy and fill vary at different structural positions. We use a 3D model of the field area, constructed using field observations and bedding data, and geomechanically restored using Move software, to determine how factors such as fold curvature and strain influence fracture variation. Fracture patterns in the Torridon Group are consistent and predictable in high strain forelimbs, however in low strain backlimbs fracture patterns are inconsistent. Heterogeneities in fracture connectivity and orientation in low strain regions do not correspond to fluctuations in strain or fold curvature. We infer that where strain is low, other factors such as lithology have a greater control on fracture formation. Despite unpredictable fracture attributes in low strain regions, fractured reservoir quality would be highest here because fractures in high strain forelimbs are infilled with quartz. Heterogeneities in fracture attribute data on fold backlimbs mean that fractured reservoir quality and reservoir potential is difficult to predict.

Thermophysical behavior of St. Peter sandstone: application to compressed air energy storage in an aquifer

Energy Technology Data Exchange (ETDEWEB)

Erikson, R.L.

1983-12-01

The long-term stability of a sandstone reservoir is of primary importance to the success of compressed air energy storage (CAES) in aquifers. The purpose of this study was to: develop experimental techniques for the operation of the CAES Porous Media Flow Loop (PMFL), an apparatus designed to study the stability of porous media in subsurface geologic environments, conduct experiments in the PMFL designed to determine the effects of temperature, stress, and humidity on the stability of candidate CAES reservoir materials, provide support for the CAES field demonstration project in Pittsfield, Illinois, by characterizing the thermophysical stability of Pittsfield reservoir sandstone under simulated field conditions.

Experimental Study of Cement - Sandstone/Shale - Brine - CO2 Interactions.

Science.gov (United States)

Carroll, Susan A; McNab, Walt W; Torres, Sharon C

2011-11-11

Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO2, and wellbore and cap rock integrity for geologic CO2 storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO2, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations. We observe marked changes in solution composition when CO2 reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO2 and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO2-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)3. Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO2 is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface.

Forming mechanism of the Ordovician karst carbonate reservoirs on the northern slope of central Tarim Basin

Directory of Open Access Journals (Sweden)

Heng Fu

2017-07-01

Full Text Available The Ordovician karst carbonate reservoirs on the northern slope of central Tarim Basin are important oil and gas exploration targets in the basin, but their dissolution mechanisms are in controversy. In this paper, based on the integrated study of sedimentation, sequence and reservoir, together with microscopic analysis and macroscopic seismic data analysis, the carbonate karst reservoirs in the study area were divided into three types: dissolved pore-cavity limestone reservoir, pore-cavity dolomite reservoir and fracture-cavity siliceous reservoir, and their forming mechanisms were discussed respectively. Some findings were obtained. First, dissolved pore-cavity limestone reservoirs are distributed in the upper Yingshan Fm and Yijianfang Fm of the Ordovician vertically, while pore-cavity dolomite reservoirs are mainly developed in the Penglai Fm and lower Yingshan Fm of the Ordovician with great thickness. Second, dissolved pore-cavity limestone reservoirs were formed by karstification on the third-order sequence boundary (lowstand tract, while pore-cavity dolomite reservoirs were formed by deep burial dolomitization controlled by karstification on the third-order sequence boundary, both of which are distributed in the highstand tract below the third-order sequence boundary. Third, siliceous reservoirs are developed under the control of faulting, as a result of reworking of deep hydrothermal fluids along faults to the limestone, and the siliceous reservoirs and their hydrothermal solution fracture-cavity systems are distributed near faults. It is further predicted that, in addition to the three types of reservoir above, platform-margin reef-flat reservoirs are developed in the Ordovician on the northern slope of central Tarim Basin.

Long-Term CO2 Exposure Experiments - Geochemical Effects on Brine-Saturated Reservoir Sandstone

Science.gov (United States)

Fischer, Sebastian; Zemke, Kornelia; Liebscher, Axel; Wandrey, Maren

2010-05-01

The injection of CO2 into deep saline aquifers is the most promising strategy for the reduction of CO2 emissions to the atmosphere via long-term geological storage. The study is part of the CO2SINK project conducted at Ketzin, situated 40 km west of Berlin. There, food grade CO2 has been pumped into the Upper Triassic Stuttgart Formation since June 2008. The main objective of the experimental program is to investigate the effects of long-term CO2 exposure on the physico-chemical properties of the reservoir rock. To achieve this goal, core samples from observation well Ktzi 202 have been saturated with synthetic brine and exposed to CO2 in high quality steel autoclaves at simulated reservoir P-T-conditions of 5.5 MPa and 40 ° C. The synthetic brine had a composition representative of the formation fluid (Förster et al., 2006) of 172.8 g/l NaCl, 8.0 g/l MgCl2×2H2O, 4.8 g/l CaCl2×2H2O and 0.6 g/l KCl. After 15 months, the first set of CO2-exposed samples was removed from the pressure vessels. Thin sections, XRD, SEM as well as EMP data were used to determine the mineralogical features of the reservoir rocks before and after the experiments. Additionally, NMR relaxation and MP was performed to measure poroperm and pore size distribution values of the twin samples. The analyzed samples are fine- to medium grained, moderately well- to well sorted and weakly consolidated sandstones. Quartz and plagioclase are the major components, while K-feldspar, hematite, white & dark mica, chlorite and illite are present in minor and varying amounts. Cements are composed of analcime, dolomite and anhydrite. Some samples show mm- to cm-scale cross-beddings. The laminae comprise lighter, quartz- and feldspar-dominated layers and dark-brownish layers with notably less quartz and feldspars. The results are consistent with those of Blaschke et al. (2008). The plagioclase composition indicates preferred dissolution of the Ca-component and a trend toward albite-rich phases or even pure

Application of advanced reservoir characterization, simulation, and production optimization strategies to maximize recovery in slope and basin clastic reservoirs, west Texas (Delaware Basin). Annual progress report, March 31, 1995--March 31, 1996

Energy Technology Data Exchange (ETDEWEB)

Dutton, S.P.; Hovorka, S.D.; Cole, A.G.

1996-08-01

The objective of this Class III project is to demonstrate that detailed reservoir characterization of clastic reservoirs in basinal sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover more of the original oil in place by strategic infill-well placement and geologically based field development. Reservoirs in the Delaware Mountain Group have low producibility (average recovery <14 percent of the original oil in place) because of a high degree of vertical and lateral heterogeneity caused by depositional processes and post-depositional diagenetic modification. Detailed correlations of the Ramsey sandstone reservoirs in Geraldine Ford field suggest that lateral sandstone continuity is less than interpreted by previous studies. The degree of lateral heterogeneity in the reservoir sandstones suggests that they were deposited by eolian-derived turbidites. According to the eolian-derived turbidite model, sand dunes migrated across the exposed shelf to the shelf break during sea-level lowstands and provided well sorted sand for turbidity currents or grain flows into the deep basin.

Abundance and distribution of northern squawfish, walleyes, and smallmouth bass in John Day Reservoir, Columbia river

International Nuclear Information System (INIS)

Beamesderfer, R.C.; Rieman, B.E.

1991-01-01

The authors used mark-recapture and catch-per-unit effort data to estimate abundances and distributions of three potential predators on juvenile salmonids migrating through John Day Reservoir in 1984-1986. The northern squawfish Ptychocheilus oregonensis was the most abundant predator (estimated population: 85, 316), followed by smallmouth bass Micropterus dolomieu (34,954) and walleye Stizostedion vitreum (15,168). Because of uncertainty in sampling and assumption of the mark-recapture estimator, the combined abundance of these three predators could lie between 50,000 and 500,000. They believe, however, that bias is probably negative, and that any errors should result in conservative estimates. Northern squawfish were common reservoir-wide, but large concentrations occurred immediately below McNary Dam near the head of John Day Reservoir. Walleyes were largely restricted to the upper third of the reservoir, whereas the number of smallmouth bass increased progressively downriver. As judged by abundance and distribution, northern squawfish have by far the greatest potential for predation on juvenile salmonids. They also expect predation to be unevenly distributed in time and space as a result of variations in the number and distribution of predators

Different effects of temperature and salinity on permeability reduction by fines migration in Berea sandstone

DEFF Research Database (Denmark)

Rosenbrand, Esther; Kjøller, Claus; Riis, Jacob Fabricius

2015-01-01

Hot water injection into geothermal aquifers is considered in order to store energy seasonally. Berea sandstone is often used as a reference formation to study mechanisms that affect permeability in reservoir sandstones. Both heating of the pore fluid and reduction of the pore fluid salinity can...

Genesis and distribution pattern of carbonate cements in lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation in the Dongying Sag, Jiyang Depression, Eastern China

DEFF Research Database (Denmark)

Yang, Tian; Cao, Yingchang; Friis, Henrik

2018-01-01

The lacustrine deep-water gravity-flow sandstone reservoirs in the third member of the Shahejie Formation are the main exploration target for hydrocarbons in the Dongying Sag, Eastern China. Carbonate cementation is responsible for much of the porosity and permeability reduction in the lacustrine...

Origin, conditions and processes of sandstone reservoir diagenetic silicification in the North Sea; Origine, conditions et processus de la silicification diagenetique de reservoir greseux en Mer du Nord

Energy Technology Data Exchange (ETDEWEB)

Blanchet, A.

2002-02-01

The petroleum reservoir qualities of sandstones are partially reduce by the presence of diagenetic quartz which occlude the cement porosity. Two sandstones reservoirs have been studied to understand the process and origin of silicification. The Brent sandstones have been sampled in the Alwyn north and Dunbar fields (North Sea) and the Franklin sandstones in the Elgin and Glenelg fields (North Sea). Fluid inclusions are often used to constrain quartz precipitation temperature. However their possible stretching with burial is still a problem. Fluid inclusion (FI) petrographic and micro-thermometric study does not show any evidence of stretching: no correlation between size, shape and homogenization temperature (Th) has been observed. Large Th range, even for FI in a single detrital grain overgrowth boundary, cannot been explained by temperature reset. The fluorescence of hydrocarbon inclusions has been analysed by micro-spectro-fluorimeter (MSF) and interpreted as density after calibration using known crude oils. Hydrocarbon inclusions show large density range for FI trapped along a single detrital grain overgrowth boundary. Raman spectroscopy reveals that aqueous inclusions are not saturated with methane. Moreover, a linear relation between methane content and Th implies pressure corrections reducing the range of trapping temperatures. The similarity of Th and MSF data between FI located along detrital grain-overgrowth boundary and within the overgrowth of a single grain indicates that FI located along the boundary are trapped after the precipitation of the first overgrowth zone. These inclusions cannot then be used to represent the beginning of the silicification. The diagenetic sequence and aluminium content in the quartz overgrowth allow to establish the origin of silica for each overgrowth zone defined in cathodoluminescence. High aluminium contents (up to 1375 ppm) are linked to feldspar dissolution which can be induced by acid meteoric water or organic acids

Geologic framework for the assessment of undiscovered oil and gas resources in sandstone reservoirs of the Upper Jurassic-Lower Cretaceous Cotton Valley Group, U.S. Gulf of Mexico region

Science.gov (United States)

Eoff, Jennifer D.; Dubiel, Russell F.; Pearson, Ofori N.; Whidden, Katherine J.

2015-01-01

The U.S. Geological Survey (USGS) is assessing the undiscovered oil and gas resources in sandstone reservoirs of the Upper Jurassic–Lower Cretaceous Cotton Valley Group in onshore areas and State waters of the U.S. Gulf of Mexico region. The assessment is based on geologic elements of a total petroleum system. Four assessment units (AUs) are defined based on characterization of hydrocarbon source and reservoir rocks, seals, traps, and the geohistory of the hydrocarbon products. Strata in each AU share similar stratigraphic, structural, and hydrocarbon-charge histories.

Influence of fluvial sandstone architecture on geothermal energy production

NARCIS (Netherlands)

Willems, C.J.L.; Maghami Nick, Hamidreza M.; Weltje, G.J.; Donselaar, M.E.; Bruhn, D.F.

2015-01-01

Fluvial sandstone reservoirs composed of stacked meander belts are considered as potential geothermal resources in the Netherlands. Net-to-gross, orientation and stacking pattern of the channel belts is of major importance for the connectivity between the injection and production well in such

Water in chalk reservoirs: 'friend or foe?'

International Nuclear Information System (INIS)

Hjuler, Morten Leth

2004-01-01

Most of the petroleum fields in the Norwegian sector of the North Sea are sandstone reservoirs; the oil and gas are trapped in different species of sandstone. But the Ekofisk Field is a chalk reservoir, which really challenges the operator companies. When oil is produced from chalk reservoirs, water usually gets in and the reservoir subsides. The subsidence may be expensive for the oil companies or be used to advantage by increasing the recovery rate. Since 60 per cent of the world's petroleum reserves are located in carbonate reservoirs, it is important to understand what happens as oil and gas are pumped out. Comprehensive studies at the Department of Petroleum Technology and Applied Geophysics at Stavanger University College in Norway show that the mechanical properties of chalk are considerably altered when the pores in the rock become saturated with oil/gas or water under different stress conditions. The processes are extremely complex. The article also maintains that the effects of injecting carbon dioxide from gas power plants into petroleum reservoirs should be carefully studied before this is done extensively

On the origin of calcite-cemented sandstones in the clearwater formation oil-sands, Alberta

Energy Technology Data Exchange (ETDEWEB)

Colquhoun, I.M.

1999-01-01

This thesis examined the formation of calcite-cemented sandstones in the Clearwater Formation within the Cold Lake and southern Primrose areas of the Alberta oil sands. Three stages of diagenesis have been recognized, both in the calcite-cemented sandstones and reservoir sands. Diagenesis of the Clearwater Formation in the Cold Lake and southern Primrose areas ended once the reservoir filled with hydrocarbons, but in the Cold Lake area, diagenesis of water-saturated sands likely continued after hydrocarbon emplacement. The reservoir sands in the formation contain a diverse clay mineral assemblage. In general, 0.7 nm clays dominate the diagenetic clay mineralogy of the Clearwater sands. Reservoir sands that contain large amounts of detrital clays and early diagenetic, grain-coating chlorite/smectite have significantly reduced bitumen-saturation. The presence of detrital and diagenetic smectitic clays complicates the removal of bitumen from the Clearwater formation using cyclic steam stimulation techniques because they swell during steam stimulation and reduce porosity and permeability of reservoir sands. Reservoir sands that contain kaolinite, feldspar and calcite react to form smectitic clays, which swell upon cyclic steam stimulation and further reduce porosity and permeability of reservoir sands. However, in the Cold Lake and Primrose areas, the dominant clay mineral is berthierine, which is associated with high calcite, which help to preserve porosity, permeability and bitumen saturation. The porous nature of bitumen-saturated, calcite-cemented sandstones that are laterally extensive could possibly provide a preferential path for steam to initiate calcite dissolution and produce significant concentrations of dissolved carbon dioxide in injected fluids. It was noted that this may then precipitate as carbonate scale within the reservoir and could cause formation damage or affect production equipment. 207 refs., 9 tabs., 58 figs., 3 appendices.

Characterization of dynamic change of Fan-delta reservoir properties in water-drive development

Energy Technology Data Exchange (ETDEWEB)

Wu Shenghe; Xiong Qihua; Liu Yuhong [Univ. of Petroleum Changping, Beijing (China)

1997-08-01

Fan-delta reservoir in Huzhuangji oil field of east China, is a typical highly heterogeneous reservoir. The oil field has been developed by water-drive for 10 years, but the oil recovery is less than 12%, and water cut is over 90%, resulting from high heterogeneity and serious dynamic change of reservoir properties. This paper aims at the study of dynamic change of reservoir properties in water-drive development. Through quantitative imaging analysis and mercury injection analysis of cores from inspection wells, the dynamic change of reservoir pore structure in water-drive development was studied. The results show that the {open_quotes}large pore channels{close_quotes} develop in distributary channel sandstone and become larger in water-drive development, resulting in more serious pore heterogeneity. Through reservoir sensitivity experiments, the rock-fluid reaction in water-drive development is studied. The results show the permeability of some distal bar sandstone and deserted channel sandstone becomes lower due to swelling of I/S clay minerals in pore throats. OD the other hand, the permeability of distributary channel and mouth bar sandstone become larger because the authigenic Koalinites in pore throats are flushed away with the increase of flow rate of injection water. Well-logging analysis of flooded reservoirs are used to study the dynamic change of reservoir properties in various flow units. The distribution of remaining oil is closely related to the types and distribution of flow units.

) Sediment petrographic characterisation and diagenetic pathways of the Miocene Agbada sandstone, Niger delta

International Nuclear Information System (INIS)

Akaegbobi, I. M; Gaupp, R.; Fischer, C.

2003-01-01

Combined petrophysical and petrographic investigations of he Agbada sandstone interbeds has been undertaken in order to determine the controlling factors on the reservoir quality of he paralic sandstone facies. Well logs, petrophysical data and a set of core samples from two wells located in the eastern onshore of he Niger delta spanning a depth interval of 3200 to 330m, formed the basic material for the present study. Four sandstone and siltstone facies units ranging form coastal bar sands through transgressive sands to marine claystones were identified based on petrophysical log signatures. Thin section analysis of a selected set of sandstone samples revealed essentially a unimodal, homogeneous grain size distribution of the detrital mineral components. Quantitative assessment of the mineralogical composition using point count method (300 points) revealed the predominance of dring. etrital quartz (85%) over feldspar minerals (9%) and lithic fragments (6%). A database generated from the point counting of the sandstones provided a broad perspective to the relative variations of the intergranular porosities (28%), cementation and matrix. These are remarkable indicators for low compaction. Authigenic kaoline and illite were identified. The partial leaching of detrital feldspars are responsible for the low percentages of intragranular volume (secondary porosity). The main controlling factor on the high porosity can be traced to either low compactional effects (overpressure?) or total leaching of unknown early cements. We suggest that the excellent reservoir properties of the Agbada sandstones are due to under compaction, caused by continuous long-term over pressuring

Numerical simulation of groundwater movement and managed aquifer recharge from Sand Hollow Reservoir, Hurricane Bench area, Washington County, Utah

Science.gov (United States)

Marston, Thomas M.; Heilweil, Victor M.

2012-01-01

cells were used in the northern and southern portions of the model where water-level data were limited. Vertically, the aquifer system was divided into 10 layers, which incorporated the Navajo Sandstone and Kayenta Formation. The model simulated recharge to the groundwater system as natural infiltration of precipitation and as infiltration of managed aquifer recharge from Sand Hollow Reservoir. Groundwater discharge was simulated as well withdrawals, shallow drains at the base of reservoir dams, and seepage to the Virgin River. During calibration, variables were adjusted within probable ranges to minimize differences among model-simulated and observed water levels, groundwater travel times, drain discharges, and monthly estimated reservoir recharge.

ANALYSIS OF OIL-BEARING CRETACEOUS SANDSTONE HYDROCARBON RESERVOIRS, EXCLUSIVE OF THE DAKOTA SANDSTONE, ON THE JICARILLA APACHE INDIAN RESERVATION, NEW MEXICO

International Nuclear Information System (INIS)

Jennie Ridgley

2000-01-01

An additional 450 wells were added to the structural database; there are now 2550 wells in the database with corrected tops on the Juana Lopez, base of the Bridge Creek Limestone, and datum. This completes the structural data base compilation. Fifteen oil and five gas fields from the Mancos-ElVado interval were evaluated with respect to the newly defined sequence stratigraphic model for this interval. The five gas fields are located away from the structural margins of the deep part of the San Juan Basin. All the fields have characteristics of basin-centered gas and can be considered as continuous gas accumulations as recently defined by the U.S. Geological Survey. Oil production occurs in thinly interbedded sandstone and shale or in discrete sandstone bodies. Production is both from transgressive and regressive strata as redefined in this study. Oil production is both stratigraphically and structurally controlled with production occurring along the Chaco slope or in steeply west-dipping rocks along the east margin of the basin. The ElVado Sandstone of subsurface usage is redefined to encompass a narrower interval; it appears to be more time correlative with the Dalton Sandstone. Thus, it was deposited as part of a regressive sequence, in contrast to the underlying rock units which were deposited during transgression

Study on the relationships between the structural evolution and sandstone-type uranium mineralization in mesozoic era and cenozoic era in the northern of Chaidam basin

International Nuclear Information System (INIS)

Liu Lin; Song Zhe; Song Xiansheng; Feng Wei

2008-01-01

By detailed expounding the characteristics of the Mesozoic and Cenozoic structural evolution in northern of Chaidam basin, the author inquires into its relationships with the sandstone-type uranium mineralization, analyzes the prospect of forming uranium deposit, and thinks that the Mesozoic and Cenozoic strata are mainly controlled by the tectonic role of the later Yanshan movement and the later Cenozoic era. The north-west palaeo-structural slope belt is formed in the later Cretacous Epoch that is favorable for developing palaeo-interlayer oxidized zone. After the slightly extensional role of the oldest Tertiary and the early Plioeene, the middle and lower Jurassic were buried, and the block-imbricated slope belts are formed in the tectonic movement of the later Cenozoic, which are favorable for developing recent interlayer oxidized zone. According to drilling, it has the conditions for forming palaeo-recent interlayer oxidized zone sandstone-type uranium deposit at the northern of Chaidam basin. Finally, the author lays his finger on the prospecting of uranium. (authors)

Fluvial-deltaic sedimentation and stratigraphy of the ferron sandstone

Science.gov (United States)

Anderson, P.B.; Chidsey, T.C.; Ryer, T.A.

1997-01-01

East-central Utah has world-class outcrops of dominantly fluvial-deltaic Turonian to Coniacian aged strata deposited in the Cretaceous foreland basin. The Ferron Sandstone Member of the Mancos Shale records the influences of both tidal and wave energy on fluvial-dominated deltas on the western margin of the Cretaceous western interior seaway. Revisions of the stratigraphy are proposed for the Ferron Sandstone. Facies representing a variety of environments of deposition are well exposed, including delta-front, strandline, marginal marine, and coastal-plain. Some of these facies are described in detail for use in petroleum reservoir characterization and include permeability structure.

Damage evaluation on oil-based drill-in fluids for ultra-deep fractured tight sandstone gas reservoirs

Directory of Open Access Journals (Sweden)

Jinzhi Zhu

2017-07-01

Full Text Available In order to explore the damage mechanisms and improve the method to evaluate and optimize the performance of formation damage control of oil-based drill-in fluids, this paper took an ultra-deep fractured tight gas reservoir in piedmont configuration, located in the Cretaceous Bashijiqike Fm of the Tarim Basin, as an example. First, evaluation experiments were conducted on the filtrate invasion, the dynamic damage of oil-based drill-in fluids and the loading capacity of filter cakes. Meanwhile, the evaluating methods were optimized for the formation damage control effect of oil-based drill-in fluids in laboratory: pre-processing drill-in fluids before grading analysis; using the dynamic damage method to simulate the damage process for evaluating the percentage of regained permeability; and evaluating the loading capacity of filter cakes. The experimental results show that (1 oil phase trapping damage and solid phase invasion are the main formation damage types; (2 the damage degree of filtrate is the strongest on the matrix; and (3 the dynamic damage degree of oil-based drill-in fluids reaches medium strong to strong on fractures and filter cakes show a good sealing capacity for the fractures less than 100 μm. In conclusion, the filter cakes' loading capacity should be first guaranteed, and both percentage of regained permeability and liquid trapping damage degree should be both considered in the oil-based drill-in fluids prepared for those ultra-deep fractured tight sandstone gas reservoirs.

Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin), Class III

Energy Technology Data Exchange (ETDEWEB)

Dutton, Shirley P.; Flanders, William A.

2001-11-04

The objective of this Class III project was demonstrate that reservoir characterization and enhanced oil recovery (EOR) by CO2 flood can increase production from slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico. Phase 1 of the project, reservoir characterization, focused on Geraldine Ford and East Ford fields, which are Delaware Mountain Group fields that produce from the upper Bell Canyon Formation (Ramsey sandstone). The demonstration phase of the project was a CO2 flood conducted in East Ford field, which is operated by Orla Petco, Inc., as the East Ford unit.

Structural diagenesis in Upper Carboniferous tight gas sandstones. Lessons learned from the Piesberg analog study

Energy Technology Data Exchange (ETDEWEB)

Steindorf, P.; Hoehne, M.; Becker, S.; Hilgers, C. [RWTH Aachen Univ. (Germany). Energy and Mineral Resources Group (EMR); Koehrer, B. [Wintershall Holding GmbH, Barnstorf (Germany)

2013-08-01

Upper Carboniferous tight gas sandstone reservoirs in NW-Germany consist of thick successions of cyclothems. Our focus is the Westphalian D of the Piesberg quarry near Osnabrueck, which exposes cemented, faulted and jointed third-order coarse- to fine-grained sandstone cycles separated by anthracite coal seams. We characterize the rocks and the lateral variation of rock properties such as porosity to better constrain input data for reservoir modelling. Three cycles are exposed, each approximately 50 m thick. Rock types can be clearly distinguished by spectral gamma ray in the quarry. Sandstones are intensely compacted and cemented with quartz and generally characterized by low porosities < 8 % (Hepycnometry on plugs and cuttings). Porosities are secondary and mainly related to detrital carbonate dissolution. Around faults dissolution is higher and the porosities can increase to up to 25%. The normal faults show different throws in the quarry and bands of shale and coal have smeared into the fault at juxtaposed beds, which may result in compartments. They dominantly strike W-E and NNW-SSE, but subordinate NE-SW striking fault patterns are also present. Joints were analyzed in a 50 x 50 m section of the quarry wall using Lidar (Light detection and ranging) laser scanning, which allows the characterization of the lithology and quantitative measurement of bedding and fracture orientation data in inaccessible areas. NNE-SSW and W-E joint sets are accompanied by northeasterly and northwesterly striking sets. Around faults, fault planes and fractures are cemented with quartz veins, showing localized mass transport. Due to the intense cementation, the sandstones can reach uniaxial strengths of more than 100 MPa normal to bedding, and approximately 50 MPa parallel to bedding. Sandstone beds within and close to faults are leached by fluids, and their uniaxial strength is reduced by a factor of more than two. Our high resolution field data enables a better understanding of

Predation by Northern Pikeminnow and tiger muskellunge on juvenile salmonids in a high–head reservoir: Implications for anadromous fish reintroductions

Science.gov (United States)

Sorel, Mark H.; Hansen, Adam G.; Connelly, Kristin A.; Wilson, Andrew C.; Lowery, Erin D.; Beauchamp, David A.

2016-01-01

The feasibility of reintroducing anadromous salmonids into reservoirs above high-head dams is affected by the suitability of the reservoir habitat for rearing and the interactions of the resident fish with introduced fish. We evaluated the predation risk to anadromous salmonids considered for reintroduction in Merwin Reservoir on the North Fork Lewis River in Washington State for two reservoir use-scenarios: year-round rearing and smolt migration. We characterized the role of the primary predators, Northern Pikeminnow Ptychocheilus oregonensis and tiger muskellunge (Northern Pike Esox lucius × Muskellunge E. masquinongy), by using stable isotopes and stomach content analysis, quantified seasonal, per capita predation using bioenergetics modeling, and evaluated the size and age structures of the populations. We then combined these inputs to estimate predation rates of size-structured population units. Northern Pikeminnow of FL ≥ 300 mm were highly cannibalistic and exhibited modest, seasonal, per capita predation on salmonids, but they were disproportionately much less abundant than smaller, less piscivorous, conspecifics. The annual predation on kokanee Oncorhynchus nerka (in biomass) by a size-structured unit of 1,000 Northern Pikeminnow having a FL ≥ 300 mm was analogous to 16,000–40,000 age-0 spring Chinook Salmon O. tshawytscha rearing year-round, or 400–1,000 age-1 smolts migrating April–June. The per capita consumption of salmonids by Northern Pikeminnow having a FL ≥ 200 mm was relatively low, due in large part to spatial segregation during the summer and the skewed size distribution of the predator population. Tiger muskellunge fed heavily on Northern Pikeminnow, other nonsalmonids, and minimally on salmonids. In addition to cannibalism within the Northern Pikeminnow population, predation by tiger muskellunge likely contributed to the low recruitment of larger (more piscivorous) Northern Pikeminnow, thereby decreasing the risk of predation to

Temperature Effects on Stiffness Moduli of Reservoir Sandstone from the Deep North Sea

DEFF Research Database (Denmark)

Orlander, Tobias; Andreassen, Katrine Alling; Fabricius, Ida Lykke

We investigate effect of testing temperature on the dynamic frame stiffness of quartz-bearing North Sea sandstone from depths of 5 km. We show that at low stress levels, the rock frame stiffens with increasing temperature and we propose an explanation for the controlling mechanisms. While...... temperature. This is unfortunate and hence, we designed a testing program with the intension of separating and quantifying effects of temperature and stress, specifically for the sandstone material subject to this study....

New Acid Combination for a Successful Sandstone Acidizing

Science.gov (United States)

Shafiq, M. U.; Mahmud, H. K. B.; Rezaee, R.

2017-05-01

With the development of new enhanced oil recovery techniques, sandstone acidizing has been introduced and played a pivotal role in the petroleum industry. Different acid combinations have been applied, which react with the formation, dissolve the soluble particles; thus increase the production of hydrocarbons. To solve the problems which occurred using current preflush sandstone acidizing technology (hydrochloric acid); a new acid combination has been developed. Core flooding experiments on sandstone core samples with dimensions 1.5 in. × 3 in. were conducted at a flow rate of 2 cm3/min. A series of hydrochloric-acetic acid mixtures with different ratios were tested under 150°F temperature. The core flooding experiments performed are aimed to dissolve carbonate, sodium, potassium and calcium particles from the core samples. These experiments are followed by few important tests which include, porosity-permeability, pH value, Inductively Coupled Plasma (ICP) analysis and Nuclear Magnetic Resonance (NMR measurements). All the results are compared with the results of conventional hydrochloric acid technology. NMR and porosity analysis concluded that the new acid combination is more effective in creating fresh pore spaces and thus increasing the reservoir permeability. It can be seen from the pore distribution before and after the acidizing. Prior applying acid; the large size of pores appears most frequently in the pore distribution while with the applied acid, it was found that the small pore size is most the predominant of the pore distribution. These results are validated using ICP analysis which shows the effective removal of calcium and other positive ions from the core sample. This study concludes that the combination of acetic-hydrochloric acid can be a potential candidate for the preflush stage of sandstone acidizing at high temperature reservoirs.

The Tiehchanshan structure of NW Taiwan: A potential geological reservoir for CO2 sequestration

Directory of Open Access Journals (Sweden)

Kenn-Ming Yang

2017-01-01

Full Text Available The Tiehchanshan structure is the largest gas-field in the outer foothills of northwestern Taiwan and has been regarded as the best site for CO2 sequestration. This study used a grid of seismic sections and wellbore data to establish a new 3-D geometry of subsurface structure, which was combined with lithofacies characters of the target reservoir rock, the Yutengping Sandstone, to build a geological model for CO2 sequestration. On the surface, the Tiehchanshan structure is characterized by two segmented anticlines offset by a tear fault. The subsurface geometry of the Tiehchanshan structure is, however, composed of two thrust-related anticlines with opposite vergence and laterally increasing fold symmetry toward each other. The folds are softly linked via the transfer zone in the subsurface, implying that the suspected tear fault in the surface transfer zone may not exist in the subsurface. The Yutengping Sandstone is composed of several sandstone units characterized by coarsening-upward cycles. The sandstone member can be further divided into four well-defined sandstone layers, separated by laterally continuous shale layers. In view of the structural and stratigraphic characteristics, the optimum area for CO2 injection and storage is in the structurally high in the northern part of the Tiehchanshan structure. The integrity of the closure and the overlying seal are not disrupted by the pre-orogenic high-angle faults. On the other hand, a thick continuous shale layer within the Yutengping Sandstone isolates the topmost sandy layer from the underlying ones and gives another important factor to the CO2 injection simulation.

An interpretation of core and wireline logs for the Petrophysical evaluation of Upper Shallow Marine sandstone reservoirs of the Bredasdorp Basin, offshore South Africa

Science.gov (United States)

Magoba, Moses; Opuwari, Mimonitu

2017-04-01

This paper embodies a study carried out to assess the Petrophysical evaluation of upper shallow marine sandstone reservoir of 10 selected wells in the Bredasdorp basin, offshore, South Africa. The studied wells were selected randomly across the upper shallow marine formation with the purpose of conducting a regional study to assess the difference in reservoir properties across the formation. The data sets used in this study were geophysical wireline logs, Conventional core analysis and geological well completion report. The physical rock properties, for example, lithology, fluid type, and hydrocarbon bearing zone were qualitatively characterized while different parameters such as volume of clay, porosity, permeability, water saturation ,hydrocarbon saturation, storage and flow capacity were quantitatively estimated. The quantitative results were calibrated with the core data. The upper shallow marine reservoirs were penetrated at different depth ranging from shallow depth of about 2442m to 3715m. The average volume of clay, average effective porosity, average water saturation, hydrocarbon saturation and permeability range from 8.6%- 43%, 9%- 16%, 12%- 68% , 32%- 87.8% and 0.093mD -151.8mD respectively. The estimated rock properties indicate a good reservoir quality. Storage and flow capacity results presented a fair to good distribution of hydrocarbon flow.

Adaptive Regulation of the Northern California Reservoir System for Water, Energy, and Environmental Management

Science.gov (United States)

Georgakakos, A. P.; Kistenmacher, M.; Yao, H.; Georgakakos, K. P.

2014-12-01

The 2014 National Climate Assessment of the US Global Change Research Program emphasizes that water resources managers and planners in most US regions will have to cope with new risks, vulnerabilities, and opportunities, and recommends the development of adaptive capacity to effectively respond to the new water resources planning and management challenges. In the face of these challenges, adaptive reservoir regulation is becoming all the more ncessary. Water resources management in Northern California relies on the coordinated operation of several multi-objective reservoirs on the Trinity, Sacramento, American, Feather, and San Joaquin Rivers. To be effective, reservoir regulation must be able to (a) account for forecast uncertainty; (b) assess changing tradeoffs among water uses and regions; and (c) adjust management policies as conditions change; and (d) evaluate the socio-economic and environmental benefits and risks of forecasts and policies for each region and for the system as a whole. The Integrated Forecast and Reservoir Management (INFORM) prototype demonstration project operated in Northern California through the collaboration of several forecast and management agencies has shown that decision support systems (DSS) with these attributes add value to stakeholder decision processes compared to current, less flexible management practices. Key features of the INFORM DSS include: (a) dynamically downscaled operational forecasts and climate projections that maintain the spatio-temporal coherence of the downscaled land surface forcing fields within synoptic scales; (b) use of ensemble forecast methodologies for reservoir inflows; (c) assessment of relevant tradeoffs among water uses on regional and local scales; (d) development and evaluation of dynamic reservoir policies with explicit consideration of hydro-climatic forecast uncertainties; and (e) focus on stakeholder information needs.This article discusses the INFORM integrated design concept, underlying

CO2 Storage Potential of the Eocene Tay Sandstone, Central North Sea, UK

Science.gov (United States)

Gent, Christopher; Williams, John

2017-04-01

Carbon Capture and Storage (CCS) is crucial for low-carbon industry, climate mitigation and a sustainable energy future. The offshore capacity of the UK is substantial and has been estimated at 78 Gt of CO2 in saline aquifers and hydrocarbon fields. The early-mid Eocene Tay Sandstone Member of the Central North Sea (CNS) is a submarine-fan system and potential storage reservoir with a theoretical capacity of 123 Mt of CO2. The Tay Sandstone comprises of 4 sequences, amalgamating into a fan complex 125km long and 40 km at a minimum of 1500 m depth striking NW-SE, hosting several hydrocarbon fields including Gannett A, B, D and Pict. In order to better understand the storage potential and characteristics, the Tay Sandstone over Quadrant 21 has been interpreted using log correlation and 3D seismic. Understanding the internal and external geometry of the sandstone as well as the lateral extent of the unit is essential when considering CO2 vertical and horizontal fluid flow pathways and storage security. 3D seismic mapping of a clear mounded feature has revealed the youngest sequence of the Tay complex; a homogenous sand-rich channel 12 km long, 1.5 km wide and on average 100 m thick. The sandstone has porosity >35%, permeability >5 D and a net to gross of 0.8, giving a total pore volume of 927x106 m3. The remaining three sequences are a series of stacked channels and interbedded mudstones which are more quiescent on the seismic, however, well logs indicate each subsequent sequence reduce in net to gross with age as mud has a greater influence in the early fan system. Nevertheless, the sandstone properties remain relatively consistent and are far more laterally extensive than the youngest sequence. The Tay Sandstone spatially overlaps several other potential storage sites including the older Tertiary sandstones of the Cromarty, Forties and Mey Members and deeper Jurassic reservoirs. This favours the Tay Sandstone to be considered in a secondary or multiple stacked

Depositional history of the reservoir sandstones, Akpor and Apara oilfields, eastern Niger Delta, Nigeria

Energy Technology Data Exchange (ETDEWEB)

Amajor, L.C.; Agbaire, D.W. (Port Harcourt Univ. (NG). Dept. of Geology)

1989-10-01

A subsurface study of the Agbada Formation in the Akpor and Apara oilfields in the eastern Niger Delta was undertaken in order to determine the depositional development of the reservoir sand-bodies. The study area comprises a maximum of 29 relatively thick sandstones, cyclically interbedded with shales of varying thicknesses. The lowest two sand units, separated by a shale unit and located near the base, produce petroleum from ten wells in both fields. Each sand-body exhibits a coarsening-upward textural gradient. The lower sand-body which is oval-shaped, moderately- to poorly-sorted, fine- to very coarse-grained, carbonaceous, with clay and lignite horizons, is interpreted as a deltaic sand. The unit appears to have migrated landwards, probably as a result of localized transgression, and developed maximum thickness between the two fields. The upper sand is fine-to-pebbly in grain size, well-sorted and glauconitic. Maximum development occurred slightly east of the delta. As the unit prograded in a predominantly southerly direction, genetic currents simultaneously caused it to be channelized. This sand-body is interpreted as an offshore marine bar. The intervening carbonaceous shale is thought to be of lagoonal origin. The pinch-out edges of these sand bodies may constitute prolific stratigraphic traps. (author).

Heavy mineral sorting in downwards injected Palaeocene sandstone, Siri Canyon, Danish North Sea

DEFF Research Database (Denmark)

Kazerouni, Afsoon Moatari; Friis, Henrik; Svendsen, Johan Byskov

2011-01-01

Post-depositional remobilization and injection of sand are often seen in deep-water clastic systems and has been recently recognised as a significant modifier of deep-water sandstone geometry. Large-scale injectite complexes have been interpreted from borehole data in the Palaeocene Siri Canyon...... of depositional structures in deep-water sandstones, the distinction between "in situ" and injected or remobilised sandstones is often ambiguous. Large scale heavy mineral sorting (in 10 m thick units) is observed in several reservoir units in the Siri Canyon and has been interpreted to represent the depositional...... sorting. In this study we describe an example of effective shear-zone sorting of heavy minerals in a thin downward injected sandstone dyke which was encountered in one of the cores in the Cecilie Field, Siri Canyon. Differences in sorting pattern of heavy minerals are suggested as a tool for petrographic...

Multinomial Logistic Regression & Bootstrapping for Bayesian Estimation of Vertical Facies Prediction in Heterogeneous Sandstone Reservoirs

Science.gov (United States)

Al-Mudhafar, W. J.

2013-12-01

Precisely prediction of rock facies leads to adequate reservoir characterization by improving the porosity-permeability relationships to estimate the properties in non-cored intervals. It also helps to accurately identify the spatial facies distribution to perform an accurate reservoir model for optimal future reservoir performance. In this paper, the facies estimation has been done through Multinomial logistic regression (MLR) with respect to the well logs and core data in a well in upper sandstone formation of South Rumaila oil field. The entire independent variables are gamma rays, formation density, water saturation, shale volume, log porosity, core porosity, and core permeability. Firstly, Robust Sequential Imputation Algorithm has been considered to impute the missing data. This algorithm starts from a complete subset of the dataset and estimates sequentially the missing values in an incomplete observation by minimizing the determinant of the covariance of the augmented data matrix. Then, the observation is added to the complete data matrix and the algorithm continues with the next observation with missing values. The MLR has been chosen to estimate the maximum likelihood and minimize the standard error for the nonlinear relationships between facies & core and log data. The MLR is used to predict the probabilities of the different possible facies given each independent variable by constructing a linear predictor function having a set of weights that are linearly combined with the independent variables by using a dot product. Beta distribution of facies has been considered as prior knowledge and the resulted predicted probability (posterior) has been estimated from MLR based on Baye's theorem that represents the relationship between predicted probability (posterior) with the conditional probability and the prior knowledge. To assess the statistical accuracy of the model, the bootstrap should be carried out to estimate extra-sample prediction error by randomly

Evaluation of input output efficiency of oil field considering undesirable output —A case study of sandstone reservoir in Xinjiang oilfield

Science.gov (United States)

Zhang, Shuying; Wu, Xuquan; Li, Deshan; Xu, Yadong; Song, Shulin

2017-06-01

Based on the input and output data of sandstone reservoir in Xinjiang oilfield, the SBM-Undesirable model is used to study the technical efficiency of each block. Results show that: the model of SBM-undesirable to evaluate its efficiency and to avoid defects caused by traditional DEA model radial angle, improve the accuracy of the efficiency evaluation. by analyzing the projection of the oil blocks, we find that each block is in the negative external effects of input redundancy and output deficiency benefit and undesirable output, and there are greater differences in the production efficiency of each block; the way to improve the input-output efficiency of oilfield is to optimize the allocation of resources, reduce the undesirable output and increase the expected output.

Lacustrine Environment Reservoir Properties on Sandstone Minerals and Hydrocarbon Content: A Case Study on Doba Basin, Southern Chad

Science.gov (United States)

Sumery, N. F. Mohd; Lo, S. Z.; Salim, A. M. A.

2017-10-01

The contribution of lacustrine environment as the hydrocarbon reservoir has been widely known. However, despite its growing importance, the lacustrine petroleum geology has received far less attention than marine due to its sedimentological complexity. This study therefore aims in developing an understanding of the unique aspects of lacustrine reservoirs which eventually impacts the future exploration decisions. Hydrocarbon production in Doba Basin, particularly the northern boundary, for instance, has not yet succeeded due to the unawareness of its depositional environment. The drilling results show that the problems were due to the: radioactive sand and waxy oil/formation damage, which all are related to the lacustrine depositional environment. Detailed study of geological and petrophysical integration on wireline logs and petrographic thin sections analysis of this environment helps in distinguishing reservoir and non-reservoir areas and determining the possible mechanism causing the failed DST results. The interpretations show that the correlation of all types> of logs and rho matrix analysis are capable in identifying sand and shale bed despite of the radioactive sand present. The failure of DST results were due to the presence of arkose in sand and waxy oil in reservoir bed. This had been confirmed by the petrographic thin section analysis where the arkose has mineral twinning effect indicate feldspar and waxy oil showing bright colour under fluorescent light. Understanding these special lacustrine environment characteristics and features will lead to a better interpretation of hydrocarbon prospectivity for future exploration.

Development and operation of Northern Natural's aquifer gas storage reservoirs

Energy Technology Data Exchange (ETDEWEB)

Martinson, E V

1969-01-01

There are no depleted (or nondepleted) oil and gas fields in Northern Natural Gas Co.'s market area. Consequently, when the search was started for a possible underground field, the company had to resort to the possibility of locating a water-filled, porous-rock formation (aquifer) in a geological structure which would form a suitable trap for gas storage. Geological research and exploratory drilling was carried on in S. Minnesota, E. Nebraska, and W.-central Iowa. An area located about 40 miles northwest of Des Moines, Iowa, near Redfield, appeared to have the most desirable characteristics for development of a gas-storage field. Drilling of deep developmental wells was started in late 1953 on a double- plunging anticline. The geological structure is similar to that of many oil and gas fields, but the porous formations contained only fresh water. To date, 2 major reservoirs and a minor reservoir have been developed in this structure. As much as 120 billion cu ft has been stored in the 3 reservoirs which supplied 43 billion cu ft gas withdrawals this past season from a total of 85 wells. A second aquifer gas-storage field is under development in N.-central Iowa about 15 miles northeast of Ft. Dodge.

Cross-fault pressure depletion, Zechstein carbonate reservoir, Weser-Ems area, Northern German Gas Basin

Energy Technology Data Exchange (ETDEWEB)

Corona, F.V.; Brauckmann, F.; Beckmann, H.; Gobi, A.; Grassmann, S.; Neble, J.; Roettgen, K. [ExxonMobil Production Deutschland GmbH (EMPG), Hannover (Germany)

2013-08-01

A cross-fault pressure depletion study in Upper Permian Zechstein Ca2 carbonate reservoir was undertaken in the Weser-Ems area of the Northern German Gas Basin. The primary objectives are to develop a practical workflow to define cross-fault pressures scenarios for Zechstein Ca2 reservoir drillwells, to determine the key factors of cross-fault pressure behavior in this platform carbonate reservoir, and to translate the observed cross-fault pressure depletion to fault transmissibility for reservoir simulation models. Analysis of Zechstein Ca2 cross-fault pressures indicates that most Zechstein-cutting faults appear to act as fluid-flow baffles with some local occurrences of fault seal. Moreover, there appears to be distinct cross-fault baffling or pressure depletion trends that may be related to the extent of the separating fault or fault system, degree of reservoir flow-path tortuosity, and quality of reservoir juxtaposition. Based on the above observations, a three-part workflow was developed consisting of (1) careful interpretation and mapping of faults and fault networks, (2) analysis of reservoir juxtaposition and reservoir juxtaposition quality, and (3) application of the observed cross-fault pressure depletion trends. This approach is field-analog based, is practical, and is being used currently to provide reliable and supportable pressure prediction scenarios for subsequent Zechstein fault-bounded drill-well opportunities.

Monitoring CO2 penetration and storage in the brine-saturated low permeable sandstone by the geophysical exploration technologies

Science.gov (United States)

Honda, H.; Mitani, Y.; Kitamura, K.; Ikemi, H.; Imasato, M.

2017-12-01

Carbon dioxide (CO2) capture and storage (CCS) plays a vital role in reducing greenhouse gas emissions. In the northern part of Kyushu region of Japan, complex geological structure (Coalfield) is existed near the CO2 emission source and has 1.06 Gt of CO2 storage capacity. The geological survey shows that these layers are formed by low permeable sandstone. It is necessary to monitor the CO2 behavior and clear the mechanisms of CO2 penetration and storage in the low permeable sandstone. In this study, measurements of complex electrical impedance (Z) and elastic wave velocity (P-wave velocity: Vp) were conducted during the supercritical CO2 injection experiment into the brine-saturated low permeable sandstone. The experiment conditions were as follows; Confining pressure: 20 MPa, Initial pore pressure: 10 MPa, 40 °, CO2 injection rate: 0.01 to 0.5 mL/min. Z was measured in the center of the specimen and Vp were measured at three different heights of the specimen at constant intervals. In addition, we measured the longitudinal and lateral strain at the center of the specimen, the pore pressure and CO2 injection volume (CO2 saturation). During the CO2 injection, the change of Z and Vp were confirmed. In the drainage terms, Vp decreased drastically once CO2 reached the measurement cross section.Vp showed the little change even if the flow rate increased (CO2 saturation increased). On the other hand, before the CO2 front reached, Z decreased with CO2-dissolved brine. After that, Z showed continuously increased as the CO2 saturation increased. From the multi-parameter (Hydraulic and Rock-physics parameters), we revealed the detail CO2 behavior in the specimen. In the brine-saturated low permeable sandstone, the slow penetration of CO2 was observed. However, once CO2 has passed, the penetration of CO2 became easy in even for brine-remainded low permeable sandstone. We conclude low permeable sandstone has not only structural storage capacity but also residual tapping

Experimental Investigation of Crack Extension Patterns in Hydraulic Fracturing with Shale, Sandstone and Granite Cores

Directory of Open Access Journals (Sweden)

Jianming He

2016-12-01

Full Text Available Hydraulic fracturing is an important method of reservoir stimulation in the exploitation of geothermal resources, and conventional and unconventional oil and gas resources. In this article, hydraulic fracturing experiments with shale, sandstone cores (from southern Sichuan Basin, and granite cores (from Inner Mongolia were conducted to investigate the different hydraulic fracture extension patterns in these three reservoir rocks. The different reactions between reservoir lithology and pump pressure can be reflected by the pump pressure monitoring curves of hydraulic fracture experiments. An X-ray computer tomography (CT scanner was employed to obtain the spatial distribution of hydraulic fractures in fractured shale, sandstone, and granite cores. From the microscopic and macroscopic observation of hydraulic fractures, different extension patterns of the hydraulic fracture can be analyzed. In fractured sandstone, symmetrical hydraulic fracture morphology could be formed, while some micro cracks were also induced near the injection hole. Although the macroscopic cracks in fractured granite cores are barely observed by naked eye, the results of X-ray CT scanning obviously show the morphology of hydraulic fractures. It is indicated that the typical bedding planes well developed in shale formation play an important role in the propagation of hydraulic fractures in shale cores. The results also demonstrated that heterogeneity influenced the pathway of the hydraulic fracture in granite cores.

Economic evaluation on tight sandstone gas development projects in China and recommendation on fiscal and taxation support policies

OpenAIRE

Zhen Yang; Lingfeng Kong; Min Du; Chenhui Zhao

2016-01-01

China is rich in tight sandstone gas resources (“tight gas” for short). For example, the Sulige Gasfield in the Ordos Basin and the Upper Triassic Xujiahe Fm gas reservoir in the Sichuan Basin are typical tight gas reservoirs. In the past decade, tight gas reserve and production both have increased rapidly in China, but tight gas reservoirs are always managed as conventional gas reservoirs without effective fiscal, taxation and policy supports. The potential of sustainable tight gas productio...

Permeability in Rotliegend gas sandstones to gas and brine as predicted from NMR, mercury injection and image analysis

DEFF Research Database (Denmark)

Rosenbrand, Esther; Fabricius, Ida Lykke; Fisher, Quentin

2015-01-01

Permeability characterisation of low permeability, clay-rich gas sandstones is part of production forecasting and reservoir management. The physically based Kozeny (1927) equation linking permeability with porosity and pore size is derived for a porous medium with a homogeneous pore size, whereas...... the pore sizes in tight sandstones can range from nm to μm. Nuclear magnetic resonance (NMR) transverse relaxation was used to estimate a pore size distribution for 63 samples of Rotliegend sandstone. The surface relaxation parameter required to relate NMR to pore size is estimated by combination of NMR...

Bluebell Field, Uinta Basin: reservoir characterization for improved well completion and oil recovery

Science.gov (United States)

Montgomery, S.L.; Morgan, C.D.

1998-01-01

Bluefield Field is the largest oil-producing area in the Unita basin of northern Utah. The field inclucdes over 300 wells and has produced 137 Mbbl oil and 177 bcf gas from fractured Paleocene-Eocene lacustrine and fluvial deposits of the Green River and Wasatch (Colton) formations. Oil and gas are produced at depths of 10 500-13 000 ft (3330-3940 m), with the most prolific reservoirs existing in over-pressured sandstones of the Colton Formation and the underlying Flagstaff Member of the lower Green River Formation. Despite a number of high-recovery wells (1-3 MMbbl), overall field recovery remains low, less than 10% original oil in place. This low recovery rate is interpreted to be at least partly a result of completion practices. Typically, 40-120 beds are perforated and stimulated with acid (no proppant) over intervals of up to 3000 ft (900 m). Little or no evaluation of individual beds is performed, preventing identification of good-quality reservoir zones, water-producing zones, and thief zones. As a result, detailed understanding of Bluebell reservoirs historically has been poor, inhibiting any improvements in recovery strategies. A recent project undertaken in Bluebell field as part of the U.S. Department of Energy's Class 1 (fluvial-deltaic reservoir) Oil Demonstration program has focused considerable effort on reservoir characterization. This effort has involved interdisciplinary analysis of core, log, fracture, geostatistical, production, and other data. Much valuable new information on reservoir character has resulted, with important implications for completion techniques and recovery expectations. Such data should have excellent applicability to other producing areas in the Uinta Basin withi reservoirs in similar lacustrine and related deposits.Bluebell field is the largest oil-producing area in the Uinta basin of northern Utah. The field includes over 300 wells and has produced 137 MMbbl oil and 177 bcf gas from fractured Paleocene-Eocene lacustrine

Application of advanced reservoir characterization, simulation, and production optimization strategies to maximize recovery in slope and basin clastic reservoirs, West Texas (Delaware Basin), Class III

Energy Technology Data Exchange (ETDEWEB)

Dutton, Shirley P.; Flanders, William A.; Zirczy, Helena H.

2000-05-24

The objective of this Class 3 project was to demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost effective way to recover a higher percentage of the original oil in place through strategic placement of infill wells and geologically based field development. Phase 1 of the project, reservoir characterization, was completed this year, and Phase 2 began. The project is focused on East Ford field, a representative Delaware Mountain Group field that produces from the upper Bell Canyon Formation (Ramsey sandstone). The field, discovered in 1960, is operated by Oral Petco, Inc., as the East Ford unit. A CO{sub 2} flood is being conducted in the unit, and this flood is the Phase 2 demonstration for the project.

Rates of consumption of juvenile salmonids and alternative prey fish by northern squawfish, walleyes, smallmouth bass, and channel catfish in John Day Reservoir, Columbia River

International Nuclear Information System (INIS)

Vigg, S.; Poe, T.P.; Prendergast, L.A.; Hansel, H.C.

1991-01-01

Adult northern squawfish Ptychocheilus oregonesis, walleyes Stizostedion vitreum, smallmouth bass Micropterus dolomieu, and channel catfish Ictalurus punctatus were sampled from four regions of John Day Reservoir from April to August 1983-1986 to quantify their consumption of 13 species of prey fish, particularly seaward-migrating juvenile Pacific salmon and steelhead (Oncorhynchus spp.). Consumption rates were estimated from field data on stomach contents and digestion rate relations determined in previous investigations. For each predator, consumption rates varied by reservoir area, month, time of day, and predator size or age. The greatest daily consumption of salmonids by northern squawfish and channel catfish occurred in the upper end of the reservoir below McNary Dam. Greatest daily predation by walleyes and smallmouth bass occurred in the middle and lower reservoir. Consumption rates of all predators were highest in July, concurrent with maximum temperature and abundance of juvenile salmonids. Feeding by the predators tended to peak after dawn and near midnight. Northern squawfish below McNary Dam exhibited this pattern, but fed mainly in the morning hours down-reservoir. The daily ration of total prey fish was highest for northern squawfish over 451 mm fork length, for walleyes 201-250 mm, for smallmouth bass 176-200 mm, and for channel catfish 401-450 mm. Averaged over all predator sizes and sampling months (April-August), the total daily ration (fish plus other prey) of smallmouth bass was about twice that of channel catfish, northern squawfish, and walleyes. However, northern squawfish was clearly the major predator on juvenile salmonids

Fe-oxide grain coatings support bacterial Fe-reducing metabolisms in 1.7-2.0 km-deep subsurface quartz arenite sandstone reservoirs of the Illinois Basin (USA

Directory of Open Access Journals (Sweden)

Yiran eDong

2014-09-01

Full Text Available The Cambrian-age Mt. Simon Sandstone, deeply buried within the Illinois Basin of the midcontinent of North America, contains quartz sand grains ubiquitously encrusted with iron-oxide cements and dissolved ferrous iron in pore-water. Although microbial iron reduction has previously been documented in the deep terrestrial subsurface, the potential for diagenetic mineral cementation to drive microbial activity has not been well studied. In this study, two subsurface formation water samples were collected at 1.72 and 2.02 km, respectively, from the Mt. Simon Sandstone in Decatur, Illinois. Low-diversity microbial communities were detected from both horizons and were dominated by Halanaerobiales of Phylum Firmicutes. Iron-reducing enrichment cultures fed with ferric citrate were successfully established using the formation water. Phylogenetic classification identified the enriched species to be related to Vulcanibacillus from the 1.72 km depth sample, while Orenia dominated the communities at 2.02 km of burial depth. Species-specific quantitative analyses of the enriched organisms in the microbial communities suggest that they are indigenous to the Mt. Simon Sandstone. Optimal iron reduction by the 1.72 km enrichment culture occurred at a temperature of 40oC (range 20 to 60oC and a salinity of 25 parts per thousand (range 25-75 ppt. This culture also mediated fermentation and nitrate reduction. In contrast, the 2.02 km enrichment culture exclusively utilized hydrogen and pyruvate as the electron donors for iron reduction, tolerated a wider range of salinities (25-200 ppt, and exhibited only minimal nitrate- and sulfate-reduction. In addition, the 2.02 km depth community actively reduces the more crystalline ferric iron minerals goethite and hematite. The results suggest evolutionary adaptation of the autochthonous microbial communities to the Mt. Simon Sandstone and carries potentially important implications for future utilization of this reservoir

Diagenesis, provenance and depositional environments of the Bunter Sandstone Formation

DEFF Research Database (Denmark)

Olivarius, Mette; Weibel, Rikke; Friis, Henrik

The Bunter Sandstone Formation in the northern North German Basin has large geothermal potential with high porosity and permeability (generally >15% and >100 mD, respectively) and with pore fluid temperatures that are adequate for geothermal energy production (c. 55–60˚C). A combined investigation...

Changes in the composition and properties of Ashalchinskoye bitumen-saturated sandstones when exposed to water vapor

Science.gov (United States)

Korolev, E.; Eskin, A.; Kolchugin, A.; Morozov, V.; Khramchenkov, M.; Gabdelvalieva, R.

2018-05-01

Ashalchinskoye bitumen deposit is an experimental platform for testing technology of high-viscosity oil extraction from reservoir rocks. Last time for enhanced of oil recovery in reservoir used pressurization a water vapor with a temperature of ∼ 180 ° C (SAGD technology). However, what happens in sandstone reservoir is little known. We did a study of the effects of water vapor on the structural components of bitumen saturated sandstone. In paper were studied the rock samples at base condition and after one week exposure by water vapour. The thermal analysis showed that steaming helps to removes light and middle oil fractions with a boiling point up to 360 ° C from oil saturated sandstones. Content of heavy oil fractions virtually unchanged. Studying the composition of water extractions of samples showed that the process of aquathermolysis of oil is accompanied by a lowering of the pH of the pore solution from 7.4 to 6.5 and rise content in several times of mobile cations Ca2+, Mg2+ and HCO3 -, SO4 2- anions. Follows from this that the thermal steam effect by bitumen saturated sandstones leads to partial oxidation of hydrocarbons with to form a carbon dioxide. The source of sulfate ions were oxidized pyrite aggregates. Due to the increasing acidity of condensed water, which fills the pore space of samples, pore fluid becomes aggressive to calcite and dolomite cement of bitumen saturated sandstones. As a result of the dissolution of carbonate cement the pore fluid enriched by calcium and magnesium cations. Clearly, that the process is accompanied by reduction of contact strength between fragments of minerals and rocks. Resulting part of compounds is separated from the outer side of samples and falls to bottom of water vapor container. Decreasing the amount of calcite and dolomite anions in samples in a steam-treated influence is confirmed by X-Ray analysis. X-Ray analysis data of study adscititious component of rocks showed that when influenced of water vapor to

Lessons learned from IOR steamflooding in a bitumen-light oil heterogeneous reservoir

NARCIS (Netherlands)

Al Mudhafar, W.J.M.; Hosseini Nasab, S.M.

2015-01-01

The Steamflooding was considered in this research to extract the discontinuous bitumen layers that are located at the oil-water contact for the heterogeneous light oil sandstone reservoir of South Rumaila Field. The reservoir heterogeneity and the bitumen layers impede water aquifer approaching into

Integrated geomechanical, petrographical and petrophysical study of the sandstones of the Wajid Group, SW Saudi Arabia

Science.gov (United States)

Benaafi, Mohammed; Hariri, Mustafa; Al-Shaibani, Abdulaziz; Abdullatif, Osman; Makkawi, Mohammed

2018-07-01

The Cambro-Permian siliciclastic succession in southwestern Saudi Arabia is represented by the Wajid Group, which consists mainly of fluvial, shallow marine, aeolian, and glacial sandstones. The Wajid Group comprises the Dibsiyah, Sanamah, Qalibah, Khusayyayn, and Juwayl Formations. It is exposed in the Wadi Al-Dawasir area and extends to Najran City. The sandstones of the Wajid Group serve as groundwater aquifers in the Wadi Al-Dawasir and Najran areas and host hydrocarbon (mainly gas) reservoirs in the Rub' Al-Khali Basin. This study aims to characterize the geomechanical properties (rock strength and Young's modulus) of the sandstones of the Wajid Group using field and experimental techniques. A further objective is to investigate the relationships between the geomechanical properties and the petrographical and petrophysical properties of the studied sandstones. The geomechanical properties of the studied sandstones vary from glacial to non-glacial sandstones, as the glacial sandstones display high values of the geomechanical properties with high variability indices. Four geological factors including grain size, cement content, porosity and permeability were observed as the main controls on the geomechanical behaviour of the studied sandstones except for the Khusayyayn sandstone, where the mineral composition was also important. Significant correlations were observed between the petrographical and petrophysical properties and the geomechanical properties of the glacial sandstones. Predictive models of the geomechanical properties (RN, UCS, and E) were generated using regression analysis to account for the glacial sandstones.

Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin), Class III

Energy Technology Data Exchange (ETDEWEB)

Dutton, Shirley P.; Flanders, William A.; Mendez, Daniel L.

2001-05-08

The objective of this Class 3 project was demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstone's of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost effective way to recover oil more economically through geologically based field development. This project was focused on East Ford field, a Delaware Mountain Group field that produced from the upper Bell Canyon Formation (Ramsey sandstone). The field, discovered in 9160, is operated by Oral Petco, Inc., as the East Ford unit. A CO2 flood was being conducted in the unit, and this flood is the Phase 2 demonstration for the project.

The effect of rock electrical parameters on the calculation of reservoir saturation

International Nuclear Information System (INIS)

Li, Xiongyan; Qin, Ruibao; Liu, Chuncheng; Mao, Zhiqiang

2013-01-01

The error in calculating a reservoir saturation caused by the error in the cementation exponent, m, and the saturation exponent, n, should be analysed. In addition, the influence of m and n on the reservoir saturation should be discussed. Based on the Archie formula, the effect of variables m and n on the reservoir saturation is analysed, while the formula for the error in calculating the reservoir saturation, caused by the error in m and n, is deduced, and the main factors affecting the error in reservoir saturation are illustrated. According to the physical meaning of m and n, it can be interpreted that they are two independent parameters, i.e., there is no connection between m and n. When m and n have the same error, the impact of the variables on the calculation of the reservoir saturation should be compared. Therefore, when the errors of m and n are respectively equal to 0.2, 0.4 and 0.6, the distribution range of the errors in calculating the reservoir saturation is analysed. However, in most cases, the error of m and n is about 0.2. When the error of m is 0.2, the error in calculating the reservoir saturation ranges from 0% to 35%. Meanwhile, when the error in n is 0.2, the error in calculating the reservoir saturation is almost always below 5%. On the basis of loose sandstone, medium sandstone, tight sandstone, conglomerate, tuff, breccia, basalt, andesite, dacite and rhyolite, this paper first analyses the distribution range and change amplitude of m and n. Second, the impact of m and n on the calculation of reservoir saturation is elaborated upon. With regard to each lithology, the distribution range and change amplitude of m are greater than those of n. Therefore, compared with n, the effect of m on the reservoir saturation is stronger. The influence of m and n on the reservoir saturation is determined, and the error in calculating the reservoir saturation caused by the error of m and n is calculated. This is theoretically and practically significant for

Sedimentology and Reservoir Characteristics of Early Cretaceous Fluvio-Deltaic and Lacustrine Deposits, Upper Abu Gabra Formation, Sufyan Sub-basin, Muglad Rift Basin, Sudan

Science.gov (United States)

Yassin, Mohamed; Abdullatif, Osman; Hariri, Mustafa

2017-04-01

Sufyan Sub-basin is an East-West trending Sub-basin located in the northwestern part of the Muglad Basin (Sudan), in the eastern extension of the West and Central Africa Rift System (WCARS). The Early Cretaceous Abu Gabra Formation considered as the main source rock in the Muglad Basin. In Sufyan Sub-basin the Early Cretaceous Upper Abu Gabra Formation is the main oil-producing reservoir. It is dominated by sandstone and shales deposited in fluvio-deltaic and lacustrine environment during the first rift cycle in the basin. Depositional and post-depositional processes highly influenced the reservoir quality and architecture. This study investigates different scales of reservoir heterogeneities from macro to micro scale. Subsurface facies analysis was analyzed based on the description of six conventional cores from two wells. Approaches include well log analysis, thin sections and scanning electron microscope (SEM) investigations, grain-size, and X-ray diffraction (XRD) analysis of the Abu Gabra sandstone. The cores and well logs analyses revealed six lithofacies representing fluvio-deltaic and lacustrine depositional environment. The sandstone is medium to coarse-grained, poorly to moderately sorted and sub-angular to subrounded, Sub-feldspathic arenite to quartz arenite. On macro-scale, reservoir quality varies within Abu Gabra reservoir where it shows progressive coarsening upward tendencies with different degrees of connectivity. The upper part of the reservoir showed well connected and amalgamated sandstone bodies, the middle to lower parts, however, have moderate to low sandstone bodies' connectivity and amalgamation. On micro-scale, sandstone reservoir quality is directly affected by textures and diagenesis.The XRD and SEM analyses show that kaolinite and chlorite clay are the common clay minerals in the studied samples. Clay matrix and quartz overgrowth have significantly reduced the reservoir porosity and permeability, while the dissolution of feldspars

Revitalizing a mature oil play: Strategies for finding and producing unrecovered oil in frio fluvial-deltaic sandstone reservoirs at South Texas. Annual report, October 1994--October 1995

Energy Technology Data Exchange (ETDEWEB)

Holtz, M.; Knox, P.; McRae, L. [and others

1996-02-01

The Frio Fluvial-Deltaic Sandstone oil play of South Texas has produced nearly 1 billion barrels of oil, yet it still contains about 1.6 billion barrels of unrecovered mobile oil and nearly the same amount of residual oil resources. Interwell-scale geologic facise models of Frio Fluvial-deltaic reservoirs are being combined with engineering assessments and geophysical evaluations in order to determine the controls that these characteristics exert on the location and volume or unrecovered mobile and residual oil. Progress in the third year centered on technology transfer. An overview of project tasks is presented.

Low-Q structure related to partially saturated pores within the reservoir beneath The Geysers area in the northern California

Science.gov (United States)

Matsubara, M.

2011-12-01

A large reservoir is located beneath The Geysers geothermal area, northern California. Seismic tomography revealed high-velocity (high-V) and low-Vp/Vs zones in the reservoir (Julian et al., 1996) and a decrease of Vp/Vs from 1991 to 1998 (Guasekera et al., 2003) owing to withdrawal of steam from the reservoir. I perform attenuation tomography in this region to investigate the state of vapor and liquid within the reservoir. The target region, 38.5-39.0°N and 122.5-123°W, covers The Geysers area. I use seismograms of 1,231 events whose focal mechanism are determined among 65,810 events recorded by the Northern California Earthquake Data Center from 2002 to 2008 in the target region. The band-pass filtered seismograms are analyzed for collecting the maximum amplitude data. There are 26 stations that have a three-component seismometer among 47 seismic stations. I use the P- and S-wave maximum amplitudes during the two seconds after the arrival of those waves in order to avoid coda effects. A total of 8,545 P- and 1,168 S-wave amplitude data for 949 earthquakes recorded at 47 stations are available for the analysis using the attenuation tomographic method derived from the velocity tomographic method (Matsubara et al., 2005, 2008) in which spatial velocity correlation and station corrections are introduced to the original code of Zhao et al. (1992). I use 3-D velocity structure obtained by Thurber et al. (2009). The initial Q value is set to 150, corresponding to the average Q of the northern California (Ford et al., 2010). At sea level, low-Q zones are found extending from the middle of the steam reservoir within the main greywacke to the south part of the reservoir. At a depth of 1 km below sea level, a low-Q zone is located solely in the southern part of the reservoir. However, at a depth of 2 km a low-Q zone is located beneath the northern part of the reservoir. At depths of 1 to 3 km a felsite batholith in the deeper portions of the reservoir, and it corresponds

Jurassic and Cretaceous clays of the northern and central North Sea hydrocarbon reservoirs reviewed

Energy Technology Data Exchange (ETDEWEB)

Wilkinson, M.; Haszeldine, R.S.; Fallick, A.E.

2006-03-15

The principal clays of the northern and central North Sea are illite (sometimes with interlayered smectite) and kaolin. Chlorite is only locally important. Although it has been proposed that kaolin within North Sea sandstones is detrital in origin, the majority of workers have concluded that it is authigenic, largely the product of feldspar alteration. Kaolin is found within a wide range of sedimentary settings (and within shales) apparently defying the notion that kaolin is an indicator of meteoric water deposition. Within sandstones, the earliest authigenic kaolin has a vermiform morphology, the distribution of which is controlled by the availability of detrital mica to act as a nucleus, and the composition of the post-depositional porewaters. This vermiform kaolin formed in meteoric water, the presence of which is easily accounted for below sub-aerial exposure surfaces in non-marine formations, and below unconformities over marine units. In fully marine sands, and even marine shale units, kaolin still occurs. It has therefore been suggested that even these locations have been flushed with meteoric water. Early vermiform kaolin recrystallizes to a more blocky morphology as burial proceeds, at least in the Brent Group. Blocky kaolin has been reported as growing before, synchronously with, and after the formation of quartz overgrowths, though oxygen isotope studies support low-temperature growth, pre-quartz. Blocky kaolin may form during meteoric flushing associated with lower Cretaceous uplift and erosion, though it is found in fault blocks that are thought to have remained below sea level. Here, the kaolin may form in stagnant meteoric water, relics of the post-depositional porewater. It has also been proposed that the blocky kaolin grew in ascending basinal waters charged with carboxylic acids and CO{sub 2}, though this hypothesis is not supported by stable oxygen isotope data. Some of the blocky kaolin is dickite, the stable polymorph above 100{sup o}C. Fibrous

Geologic-seismic models, prediction of shallow-water lacustrine delta sandbody and hydrocarbon potential in the Late Miocene, Huanghekou Sag, Bohai Bay Basin, northern China

Directory of Open Access Journals (Sweden)

Hao Liu

2018-01-01

Full Text Available The Huanghekou Sag is located at the southeast part of the Bohai Bay Basin, northern China. Large-scale shallow lake delta developed in the Neogene provided suitable geological conditions for the formation of a subtle oil-gas reservoir in this area. The key for analyzing sandstone reservoir and sedimentary facies is by using seismic attributes (amplitude to establish the relationship between lithology combination and seismic attributes. The lower unit of Late Miocene Minghuazhen Formation at the BZ34 block in the Huanghekou Sag was subdivided into 10 parasequence sets (PSS. Thicker sandstones mainly occurred in PSS1 and PSS10, whereas thin sandstones are mostly observed within other parasequence sets. This study presents statistics and analyses of lithology, i.e., statistics of root-mean-square (RMS amplitude and lithology of well locations in different parasequence sets of the study area, as well as 1-D forward seismic models of 7 types of lithology combinations, the establishment of a spatial distribution of 2-D sandbody, forward seismic models etc. Our study indicates that high amplitude peaks correspond to thicker sandbodies, while low amplitude indicates non-development of sandbodies (generally less than 2 m, and medium amplitude agrees well with large sets of mudstones interbedded with medium and thinner sandstones. Different sand–mudstone combinations genetically reflect a combination of multiple micro-facies, therefore, amplitude features can predict sandbodies as well as facies characteristics.

High-resolution 3D X-ray microtomography as tool to investigate size distribution of grain phase and pore space in sandstones

Science.gov (United States)

Kahl, Wolf-Achim; Holzheid, Astrid

2013-04-01

The geometry and internal structures of sandstone reservoirs, like grain size, sorting, degree of bioturbation, and the history of the diagenetic alterations determine the quantity, flow rates, and recovery of hydrocarbons present in the pore space. In this respect, processes influencing the deep reservoir quality in sandstones are either of depositional, shallow diagenetic, or deep-burial origin. To assess the effect of compaction and cementation on the pore space during diagenesis, we investigated a set of sandstone samples using high-resolution microtomography (µ-CT). By high-resolution µ-CT, size distributions (in 2D and 3D), surface areas and volume fractions of the grain skeleton and pore space of sandstones and - in addition - of mineral powders have been determined. For this study, we analysed aliquots of sandstones that exhibit either complete, partial or no cemententation of the pore space, and sets of mineral powders (quartz, feldspar, calcite). As the resolution of the µ-CT scans is in the µm-range, the surface areas determined for sandstones and powders do detect the geometric surface of the material (Kahl & Holzheid, 2010). Since there are differing approaches to "size" parameters like e.g., long/short particle axes, area equivalent radius, Feret-diameter (2D), and structural thickness (3D), we decided to illustrate the effect of various size determinations for (a) single grains, (b) grain skeletons, and (c) pore space. Therefor, the computer-aided morphometric analysis of the segmented 3D models of the reconstructed scan images comprises versatile calculation algorithms. For example, size distribution of the pore space of partially cemented sandstones can be used to infer the timing of the formation of the cement in respect to tectonic/diagenetic activities. In the case of a late-stage partial cementation of a Bunter sandstone, both pore space and cement phase show identical size distributions. On the contrary, the anhydrite cement of a

Cyclicity and reservoir properties of Lower-Middle Miocene sediments of South Kirinsk oil and gas field

Science.gov (United States)

Kurdina, Nadezhda

2017-04-01

Exploration and additional exploration of oil and gas fields, connected with lithological traps, include the spreading forecast of sedimentary bodies with reservoir and seal properties. Genetic identification and forecast of geological bodies are possible in case of large-scale studies, based on the study of cyclicity, structural and textural features of rocks, their composition, lithofacies and depositional environments. Porosity and permeability evaluation of different reservoir groups is also an important part. Such studies have been successfully completed for productive terrigenous Dagi sediments (Lower-Middle Miocene) of the north-eastern shelf of Sakhalin. In order to identify distribution of Dagi reservoirs with different properties in section, core material of the one well of South Kirinsk field has been studied (depth interval from 2902,4 to 2810,5 m). Productive Dagi deposits are represented by gray-colored sandstones with subordinate siltstones and claystones (total thickness 90,5 m). Analysis of cyclicity is based on the concepts of Vassoevich (1977), who considered cycles as geological body, which is the physical result of processes that took place during the sedimentation cycle. Well section was divided into I-X units with different composition and set of genetic features due to layered core description and elementary cyclites identification. According to description of thin sections and results of cylindrical samples porosity and permeability studies five groups of reservoirs were determined. There are coarse-grained and fine-coarse-grained sandstones, fine-grained sandstones, fine-grained silty sandstones, sandy siltstones and siltstones. It was found, in Dagi section there is interval of fine-coarse-grained and coarse-grained sandstones with high petrophysical properties: permeability 3000 mD, porosity more than 25%, but rocks with such properties spread locally and their total thickness is 6 meters only. This interval was described in the IV unit

Differences in microbial community composition between injection and production water samples of water flooding petroleum reservoirs

Directory of Open Access Journals (Sweden)

P. K. Gao

2015-06-01

Full Text Available Microbial communities in injected water are expected to have significant influence on those of reservoir strata in long-term water flooding petroleum reservoirs. To investigate the similarities and differences in microbial communities in injected water and reservoir strata, high-throughput sequencing of microbial partial 16S rRNA of the water samples collected from the wellhead and downhole of injection wells, and from production wells in a homogeneous sandstone reservoir and a heterogeneous conglomerate reservoir were performed. The results indicate that a small number of microbial populations are shared between the water samples from the injection and production wells in the sandstone reservoir, whereas a large number of microbial populations are shared in the conglomerate reservoir. The bacterial and archaeal communities in the reservoir strata have high concentrations, which are similar to those in the injected water. However, microbial population abundance exhibited large differences between the water samples from the injection and production wells. The number of shared populations reflects the influence of microbial communities in injected water on those in reservoir strata to some extent, and show strong association with the unique variation of reservoir environments.

Research on geochronology and uranium source of sandstone-hosted uranium ore-formation in major uranium-productive basins, Northern-China

International Nuclear Information System (INIS)

Xia Yuliang; Liu Hanbin; Lin Jinrong; Fan Guang; Hou Yanxian

2004-12-01

A method is developed for correcting uranium content in uranium ore samples by considering the U-Ra equilibrium coefficient, then a U-Pb isochron is drawn up. By performing the above correction ore-formation ages of sandstone-hosted uranium mineralization which may be more realistic have been obtained. The comparative research on U-Pb isotopic ages of detritic zircon in ore-hosting sandstone and zircon in intermediate-acid igneous rocks in corresponding provenance area indicates that the ore-hosting sandstone is originated from the erosion of intermediate-acid igneous rocks and the latters are the material basis for the formation of the uranium-rich sandstone beds. On the basis of the study on U-Pb isotopic system evolution of the provenance rocks and sandstones from ore-hosting series, it is verified that the uranium sources of the sandstone-hosted uranium deposit are: the intermediate-acid igneous rocks with high content of mobile uranium, and the sandstone bodies pre-concentrated uranium. (authors)

Elevated Uranium in Aquifers of the Jacobsville Sandstone

Science.gov (United States)

Sherman, H.; Gierke, J.

2003-12-01

The EPA has announced a new standard for uranium in drinking water of 30 parts per billion (ppb). This maximum contaminant level (MCL) takes effect for community water supplies December 2003. The EPA's ruling has heightened awareness among residential well owners that uranium in drinking water may increase the risk of kidney disease and cancer and has created a need for a quantified, scientific understanding of the occurrence and distribution of uranium isotopes in aquifers. The authors are investigating the occurrence of elevated uranium in northern Michigan aquifers of the Middle Proterozoic Jacobsville sandstone, a red to mottled sequence of sandstones, conglomerates, siltstones and shales deposited as basin fill in the 1.1 Ga Midcontinent rift. Approximately 25% of 300 well water samples tested for isotopic uranium have concentrations above the MCL. Elevated uranium occurrences are distributed throughout the Jacobsville sandstone aquifers stretching across Michigan's Upper Peninsula. However, there is significant variation in well water uranium concentrations (from 0.01 to 190 ppb) and neighboring wells do not necessarily have similar concentrations. The authors are investigating hydrogeologic controls on ground water uranium concentrations in the Jacobsville sandstone, e.g. variations in lithology, mineralogy, groundwater residence time and geochemistry. Approximately 2000' of Jacobsville core from the Amoco St. Amour well was examined in conjunction with the spectral gamma ray log run in the borehole. Spikes in equivalent uranium (eU) concentration from the log are frequently associated with clay and heavy mineral layers in the sandstone core. The lithology and mineralogy of these layers will be determined by analysis of thin sections and x-ray diffraction. A portable spectrometer, model GRS-2000/BL, will be used on the sandstone cliffs along Lake Superior to characterize depositional and lithologic facies of the Jacobsville sandstone in terms of

Reconstructing depositional processes and history from reservoir stratigraphy: Englebright Lake, Yuba River, northern California

Science.gov (United States)

Snyder, N.P.; Wright, S.A.; Alpers, Charles N.; Flint, L.E.; Holmes, C.W.; Rubin, D.M.

2006-01-01

Reservoirs provide the opportunity to link watershed history with its stratigraphic record. We analyze sediment cores from a northern California reservoir in the context of hydrologic history, watershed management, and depositional processes. Observations of recent depositional patterns, sediment-transport calculations, and 137CS geochronology support a conceptual model in which the reservoir delta progrades during floods of short duration (days) and is modified during prolonged (weeks to months) drawdowns that rework topset beds and transport sand from topsets to foresets. Sediment coarser than 0.25-0.5 mm. deposits in foresets and topsets, and finer material falls out of suspension as bottomset beds. Simple hydraulic calculations indicate that fine sand (0.063-0.5 mm) is transported into the distal bottomset area only during floods. The overall stratigraphy suggests that two phases of delta building occurred in the reservoir. The first, from dam construction in 1940 to 1970, was heavily influenced by annual, prolonged >20 m drawdowns of the water level. The second, built on top of the first, reflects sedimentation from 1970 to 2002 when the influence of drawdowns was less. Sedimentation rates in the central part of the reservoir have declined ???25% since 1970, likely reflecting a combination of fewer large floods, changes in watershed management, and winnowing of stored hydraulic mining sediment. Copyright 2006 by the American Geophysical Union.

Architecture and quantitative assessment of channeled clastic deposits, Shihezi sandstone (Lower Permian, Ordos Basin, China

Directory of Open Access Journals (Sweden)

Chengye Jia

2017-02-01

Full Text Available Lower Permian Shihezi sandstone in Ordos Basin is the largest gas reservoir in China. Architecture elements of channel, overbank and floodplain facies of braided channel deposits were identified through an outcrops survey, and their proportion of channel facies have been quantitatively estimated from well logging. Characteristics of architecture elements, such as sand thickness, bounding surfaces and lithofacies were investigated through outcrops and core. Petrology of Shihezi sandstone has also been studied in detail. Analysis on sandstone components shows that monocrystalline quartz with approximately 76% bulk volume, and lithic up to 5%–45% bulk volume, are the two main components. Litharenite and lithic quartz sandstone are the main rock types. Compaction is concluded by former researchers as the control factor of low permeability. Examination through thin section reveals that secondary pores developed well in coarse sand. Inter-granular dissolution is included as the positive effect to increasing porosity, and is concluded as the control factor to the generation of net pay. Scale of coarse grained channel fills and channel bar sandstone bodies are quantitatively estimated. Strike-oriented, dip-oriented, and vertical distribution of channel fills and channel bar sandstone bodies have been investigated. The geometry of sand bodies can be depicted as an elongated lens. Subsurface mapping reveals that channel sandstone bodies distribute widely from both lateral and longitudinal cross section profiles, and are poorly connected.

Diagenetic history of the Surma Group sandstones (Miocene) in the Surma Basin, Bangladesh

Science.gov (United States)

Rahman, M. Julleh Jalalur; McCann, Tom

2012-02-01

This study examines the various diagenetic controls of the Miocene Surma Group sandstones encountered in petroleum exploration wells from the Surma Basin, which is situated in the northeastern part of the Bengal Basin, Bangladesh. The principal diagenetic minerals/cements in the Surma Group sandstones are Fe-carbonates (with Fe-calcite dominating), quartz overgrowths and authigenic clays (predominantly chlorite, illite-smectite and minor kaolin). The isotopic composition of the carbonate cement revealed a narrow range of δ 18O values (-10.3‰ to -12.4‰) and a wide range of δ 13C value (+1.4‰ to -23.1‰). The δ 13C VPDB and δ 18O VPDB values of the carbonate cements reveal that carbon was most likely derived from the thermal maturation of organic matter during burial, as well as from the dissolution of isolated carbonate clasts and precipitated from mixed marine-meteoric pore waters. The relationship between the intergranular volume (IGV) versus cement volume indicates that compaction played a more significant role than cementation in destroying the primary porosity. However, cementation also played a major role in drastically reducing porosity and permeability in sandstones with poikilotopic, pore-filling blocky cements formed in early to intermediate and deep burial areas. In addition to Fe-carbonate cements, various clay minerals including illite-smectite and chlorite occur as pore-filling and pore-lining authigenic phases. Significant secondary porosity has been generated at depths from 2500 m to 4728 m. The best reservoir rocks found at depths of 2500-3300 m are well sorted, relatively coarse grained; more loosely packed and better rounded sandstones having good porosities (20-30%) and high permeabilities (12-6000 mD). These good quality reservoir rocks are, however, not uniformly distributed and can be considered to be compartmentalized as a result of interbedding with sandstone layers of low to moderate porosities, low permeabilities owing to poor

Research and performance evaluation on an HA integrated acid system for sandstone acidizing

Directory of Open Access Journals (Sweden)

Liqiang Zhao

2018-03-01

Full Text Available When the conventional sandstone acidizing technologies are adopted, many slugs are needed in the injection of prepad fluid, treatment fluid and postpad fluid, and consequently the production and operation suffers inconveniences and difficulties. In view of this, a kind of HA integrated acid system which is mainly composed of organic polybasic acids (HA+HCl + HF and an efficient organic solvent was developed in this paper based on the idea of integrated acid replacing ''multiple steps'' and high efficiency and intensification. Via this HA integrated acid system, the complicated blockage in sandstone reservoirs can be removed effectively. Then, experiments were carried out on this system to evaluate its performance in terms of its retardance, organic blockage dissolution, chelating and precipitation inhibition. It is indicated that this new system can not only realize the acidizing of conventional integrated acid, but also present a good retarding performance by controlling H+ multi-stage ionization step by step and by forming silica acid-aluminum phosphonate film on the surface of clay minerals; that via this new HA integrated acid system, the organic blockage can be removed efficiently; and that it is wider in pH solution range than conventional APCs (aminopolycarboxyliates chelants, stronger in chelating capacity of Ca2+, Mg2+ and Fe3+ than conventional chelants (e.g. EDTA, NTA and DTPA, and better in precipitation inhibition on metal fluoride, fluosilicic acid alkali metal, fluoaluminic acid alkali metal and hydroxide than multi-hydrogen acid, fluoboric acid and mud acid systems. These research results provide a technical support for the plugging removal in high-temperature deep oil and gas reservoirs. Keywords: Organic polybasic acid, Integrated acid, Retardance, Chelating, Precipitation, Acidizing, Sandstone, Reservoir

Lack of inhibiting effect of oil emplacement on quartz cementation: Evidence from Cambrian reservoir sandstones, Paleozoic Baltic Basin

DEFF Research Database (Denmark)

Molenaar, Nicolaas; Cyziene, Jolanta; Sliaupa, Saulius

2008-01-01

Currently, the question of whether or not the presence of oil in sandstone inhibits quartz cementation and preserves porosity is still debated. Data from a number of Cambrian sandstone oil fields and dry fields have been studied to determine the effects of oil emplacement on quartz cementation. T...

Assessing water reservoirs management and development in Northern Vietnam

Directory of Open Access Journals (Sweden)

A. Castelletti

2012-01-01

Full Text Available In many developing countries water is a key renewable resource to complement carbon-emitting energy production and support food security in the face of demand pressure from fast-growing industrial production and urbanization. To cope with undergoing changes, water resources development and management have to be reconsidered by enlarging their scope across sectors and adopting effective tools to analyze current and projected infrastructure potential and operation strategies. In this paper we use multi-objective deterministic and stochastic optimization to assess the current reservoir operation and planned capacity expansion in the Red River Basin (Northern Vietnam, and to evaluate the potential improvement by the adoption of a more sophisticated information system. To reach this goal we analyze the historical operation of the major controllable infrastructure in the basin, the HoaBinh reservoir on the Da River, explore re-operation options corresponding to different tradeoffs among the three main objectives (hydropower production, flood control and water supply, using multi-objective optimization techniques, namely Multi-Objective Genetic Algorithm. Finally, we assess the structural system potential and the need for capacity expansion by application of Deterministic Dynamic Programming. Results show that the current operation can only be relatively improved by advanced optimization techniques, while investment should be put into enlarging the system storage capacity and exploiting additional information to inform the operation.

Continental Environment of Triassic Alluvial Beds in the Northern North Sea Area: Core Examples from the Lunde Formation, Snorre Field

Energy Technology Data Exchange (ETDEWEB)

Nystuen, Johan Petter; Bergan, Morten

1999-07-01

Alluvial processes transport and deposit gravel, sand and mud in a series of depositional systems such as alluvial fans, fluvial channels, floodplain and lacustrine basins. In the northernmost part of the North Sea alluvial sandstones form major reservoir rocks in several oil fields in the Tampen Spur area. In the Snorre Field, the Norian- Early Rhaetian Lunde Formation has given a great database from exploration and production wells, seismic studies, reservoir modelling, production experience and comparative analogue studies on facies distribution, alluvial architecture, heterogeneities and reservoir properties of alluvial successions. The Lunde Formation is subdivided in three members, the lower, middle and upper Lunde members, with the upper member being the main part of the Lunde reservoir rocks. The scope of presenting core samples from the upper Lunde member is to demonstrate main alluvial facies and facies associations, how facies analysis proceeds into construction of conceptual fluvial models that in turn are fundamental in evaluation of reservoir heterogeneities and reservoir modelling. The upper Lunde member consists of repeated units of red and grey sandstone and mudstone. Sandstones are dominantly medium-grained with common range from coarse- to very fine-grained. A basic building stone of the alluvial succession consists of a thick single- or multi-storey sandstone body overlain by a thick mudstone unit. Such couplets form allostratigraphic units and define the main reservoir zones.

Depositional and diagenetic variability within the Cambrian Mount Simon Sandstone: Implications for carbon dioxide sequestration

Science.gov (United States)

Bowen, B.B.; Ochoa, R.I.; Wilkens, N.D.; Brophy, J.; Lovell, T.R.; Fischietto, N.; Medina, C.R.; Rupp, J.A.

2011-01-01

The Cambrian Mount Simon Sandstone is the major target reservoir for ongoing geologic carbon dioxide (CO2) sequestration demonstrations throughout the midwest United States. The potential CO2 reservoir capacity, reactivity, and ultimate fate of injected CO2 depend on textural and compositional properties determined by depositional and diagenetic histories that vary vertically and laterally across the formation. Effective and efficient prediction and use of the available pore space requires detailed knowledge of the depositional and diagenetic textures and mineralogy, how these variables control the petrophysical character of the reservoir, and how they vary spatially. Here, we summarize the reservoir characteristics of the Mount Simon Sandstone based on examination of geophysical logs, cores, cuttings, and analysis of more than 150 thin sections. These samples represent different parts of the formation and depth ranges of more than 9000 ft (>2743 m) across the Illinois Basin and surrounding areas. This work demonstrates that overall reservoir quality and, specifically, porosity do not exhibit a simple relationship with depth, but vary both laterally and with depth because of changes in the primary depositional facies, framework composition (i.e., feldspar concentration), and diverse diagenetic modifications. Diagenetic processes that have been significant in modifying the reservoir include formation of iron oxide grain coatings, chemical compaction, feldspar precipitation and dissolution, multiple generations of quartz overgrowth cementation, clay mineral precipitation, and iron oxide cementation. These variables provide important inputs for calculating CO2 capacity potential, modeling reactivity, and are also an important baseline for comparisons after CO2 injection. Copyright ??2011. The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

Geological Characterisation of Depleted Oil and Gas Reservoirs for ...

African Journals Online (AJOL)

Dr Tse

The reservoir formation consists of multilayered alternating beds of sandstone and shale cap rocks ... In the oil sector, Nigeria is one of the highest emitters ... Industrial emission and flaring .... integration of the 3D seismic data and wireline logs.

Performance of Different Acids on Sandstone Formations

Directory of Open Access Journals (Sweden)

M. A. Zaman

2013-12-01

Full Text Available Stimulation of sandstone formations is a challenging task, which involves several chemicals and physical interactions of the acid with the formation. Some of these reactions may result in formation damage. Mud acid has been successfully used to stimulate sandstone reservoirs for a number of years. It is a mixture of hydrofluoric (HF and hydrochloric (HCl acids designed to dissolve clays and siliceous fines accumulated in the near-wellbore region. Matrix acidizing may also be used to increase formation permeability in undamaged wells. The change may be up to 50% to 100% with the mud acid. For any acidizing process, the selection of acid (Formulation and Concentration and the design (Pre-flush, Main Acid, After-flush is very important. Different researchers are using different combinations of acids with different concentrations to get the best results for acidization. Mainly the common practice is combination of Hydrochloric Acid – Hydrofluoric with Concentration (3% HF – 12% HCl. This paper presents the results of a laboratory investigation of Orthophosphoric acid instead of hydrochloric acid in one combination and the second combination is Fluoboric and formic acid and the third one is formic and hydrofluoric acid. The results are compared with the mud acid and the results calculated are porosity, permeability, and FESEM Analysis and Strength tests. All of these new combinations shows that these have the potential to be used as acidizing acids on sandstone formations.

Geologic assessment of undiscovered conventional oil and gas resources in the Lower Paleogene Midway and Wilcox Groups, and the Carrizo Sand of the Claiborne Group, of the Northern Gulf coast region

Science.gov (United States)

Warwick, Peter D.

2017-09-27

The U.S. Geological Survey (USGS) recently conducted an assessment of the undiscovered, technically recoverable oil and gas potential of Tertiary strata underlying the onshore areas and State waters of the northern Gulf of Mexico coastal region. The assessment was based on a number of geologic elements including an evaluation of hydrocarbon source rocks, suitable reservoir rocks, and hydrocarbon traps in an Upper Jurassic-Cretaceous-Tertiary Composite Total Petroleum System defined for the region by the USGS. Five conventional assessment units (AUs) were defined for the Midway (Paleocene) and Wilcox (Paleocene-Eocene) Groups, and the Carrizo Sand of the Claiborne Group (Eocene) interval including: (1) the Wilcox Stable Shelf Oil and Gas AU; (2) the Wilcox Expanded Fault Zone Gas and Oil AU; (3) the Wilcox-Lobo Slide Block Gas AU; (4) the Wilcox Slope and Basin Floor Gas AU; and (5) the Wilcox Mississippi Embayment AU (not quantitatively assessed).The USGS assessment of undiscovered oil and gas resources for the Midway-Wilcox-Carrizo interval resulted in estimated mean values of 110 million barrels of oil (MMBO), 36.9 trillion cubic feet of gas (TCFG), and 639 million barrels of natural gas liquids (MMBNGL) in the four assessed units. The undiscovered oil resources are almost evenly divided between fluvial-deltaic sandstone reservoirs within the Wilcox Stable Shelf (54 MMBO) AU and deltaic sandstone reservoirs of the Wilcox Expanded Fault Zone (52 MMBO) AU. Greater than 70 percent of the undiscovered gas and 66 percent of the natural gas liquids (NGL) are estimated to be in deep (13,000 to 30,000 feet), untested distal deltaic and slope sandstone reservoirs within the Wilcox Slope and Basin Floor Gas AU.

Stratigraphic and structural compartmentalization observed within a model turbidite reservoir, Pennsylvanian Upper Jackfork Formation, Hollywood Quarry, Arkansas

Energy Technology Data Exchange (ETDEWEB)

Slatt, R. [Colorado School of Mines, Golden, CO (United States); Jordan, D. [Arco International Oil and Gas Co., Plano, TX (United States); Stone, C. [Arkansas Geological Commission, Little Rock, AR (United States)] [and others

1995-08-01

Hollywood Quarry is a 600 x 375 x 150 ft. (200 x 125 x 50m) excavation which provides a window into lower Pennsylvanian Jackfork Formation turbidite stratal architecture along the crest of a faulted anticlinal fold. A variety of turbidite facies are present, including: (a) lenticular, channelized sandstones, pebbly sandstones, and conglomerates within shale, (b) laterally continuous, interbedded thin sandstones and shales, and (c) thicker, laterally continuous shales. The sandstone and shale layers we broken by several strike-slip and reverse faults, with vertical displacements of up to several feet. This combination of facies and structural elements has resulted in a highly compartmentalized stratigraphic interval, both horizontally and vertically, along the anticlinal flexure. The quarry can be considered analogous to a scaled-down turbidite reservoir. Outcrop gamma-ray logs, measured sections, a fault map, and cross sections provide a database which is analogous to what would be available for a subsurface reservoir. Thus, the quarry provides an ideal outdoor geologic and engineering {open_quote}workshop{close_quote} venue for visualizing the potential complexities of a combination structural-stratigraphic (turbidite) reservoir. Since all forms of compartmentalization are readily visible in the quarry, problems related to management of compartmentalized reservoirs can be discussed and analyzed first-hand while standing in the quarry, within this {open_quote}model reservoir{close_quotes}. These problems include: (a) the high degree of stratigraphic and structural complexity that may be encountered, even at close well spacings, (b) uncertainty in well log correlations and log-shape interpretations, (c) variations in volumetric calculations as a function of amount of data available, and (d) potential production problems associated with specific {open_quote}field{close_quote} development plans.

Interpreting Fracture Patterns in Sandstones Interbedded with Ductile Strata at the Salt Valley Anticline, Arches National Park, Utah; TOPICAL

International Nuclear Information System (INIS)

LORENZ, JOHN C.; COOPER, SCOTT P.

2001-01-01

Sandstones that overlie or that are interbedded with evaporitic or other ductile strata commonly contain numerous localized domains of fractures, each covering an area of a few square miles. Fractures within the Entrada Sandstone at the Salt Valley Anticline are associated with salt mobility within the underlying Paradox Formation. The fracture relationships observed at Salt Valley (along with examples from Paleozoic strata at the southern edge of the Holbrook basin in northeastern Arizona, and sandstones of the Frontier Formation along the western edge of the Green River basin in southwestern Wyoming), show that although each fracture domain may contain consistently oriented fractures, the orientations and patterns of the fractures vary considerably from domain to domain. Most of the fracture patterns in the brittle sandstones are related to local stresses created by subtle, irregular flexures resulting from mobility of the associated, interbedded ductile strata (halite or shale). Sequential episodes of evaporite dissolution and/or mobility in different directions can result in multiple, superimposed fracture sets in the associated sandstones. Multiple sets of superimposed fractures create reservoir-quality fracture interconnectivity within restricted localities of a formation. However, it is difficult to predict the orientations and characteristics of this type of fracturing in the subsurface. This is primarily because the orientations and characteristics of these fractures typically have little relationship to the regional tectonic stresses that might be used to predict fracture characteristics prior to drilling. Nevertheless, the high probability of numerous, intersecting fractures in such settings attests to the importance of determining fracture orientations in these types of fractured reservoirs

Characterization of oil and gas reservoir heterogeneity

Energy Technology Data Exchange (ETDEWEB)

Tyler, N.; Barton, M.D.; Bebout, D.G.; Fisher, R.S.; Grigsby, J.D.; Guevara, E.; Holtz, M.; Kerans, C.; Nance, H.S.; Levey, R.A.

1992-10-01

Research described In this report addresses the internal architecture of two specific reservoir types: restricted-platform carbonates and fluvial-deltaic sandstones. Together, these two reservoir types contain more than two-thirds of the unrecovered mobile oil remaining ill Texas. The approach followed in this study was to develop a strong understanding of the styles of heterogeneity of these reservoir types based on a detailed outcrop description and a translation of these findings into optimized recovery strategies in select subsurface analogs. Research targeted Grayburg Formation restricted-platform carbonate outcrops along the Algerita Escarpment and In Stone Canyon In southeastern New Mexico and Ferron deltaic sandstones in central Utah as analogs for the North Foster (Grayburg) and Lake Creek (Wilcox) units, respectively. In both settings, sequence-stratigraphic style profoundly influenced between-well architectural fabric and permeability structure. It is concluded that reservoirs of different depositional origins can therefore be categorized Into a heterogeneity matrix'' based on varying intensity of vertical and lateral heterogeneity. The utility of the matrix is that it allows prediction of the nature and location of remaining mobile oil. Highly stratified reservoirs such as the Grayburg, for example, will contain a large proportion of vertically bypassed oil; thus, an appropriate recovery strategy will be waterflood optimization and profile modification. Laterally heterogeneous reservoirs such as deltaic distributary systems would benefit from targeted infill drilling (possibly with horizontal wells) and improved areal sweep efficiency. Potential for advanced recovery of remaining mobile oil through heterogeneity-based advanced secondary recovery strategies In Texas is projected to be an Incremental 16 Bbbl. In the Lower 48 States this target may be as much as 45 Bbbl at low to moderate oil prices over the near- to mid-term.

Petrographic study of core plugs from lower goru sandstones

International Nuclear Information System (INIS)

Memon, M.K.; Tunio, A.; Leghari, A.

2008-01-01

Petrographic rock type description is a fundamental component in the reservoir description processes and typically included measurement to identify sediment source, texture, composition and mineralogy. Petroleum workers have long used the Petrographic microscope as an in put device to aid in the study of pore systems. Standard Petrographic thin sections are typically 30 micrometers thick and are usually illuminated by transmitted light. Experienced examiners have trained themselves to see information such as pore size, mineralogy, compaction, etc by disregarding artifacts produced by passing light through a section. This method is adequate for qualitative interpretation of data from thin sections. Rocks in thin section under a microscope display great complexity in pore sizes and shapes. Petrographic study provides measurement on rock texture. Texture deals with the size, shape and arrangement of the component minerals of a rock. It is essentially the micro geometry of the rock. Permeability of collected core plugs of lower Goru sandstones was measured. From this Petrographic study we have identified as the sandstone of Lower Goru constitute almost entirely of quartz. The grains range in size from very fine to medium, moderately well sorted to well sorted and rounded to sub rounded in shape. Particularly attention was paid to mineral content present in Lower Goru Sandstone. The mineral composition from these core plugs of Lower Goru Sandstone as identified contain about 70-80% Quartz with traces of feldspar, muscovite, biotite, Epidote and hornblende. Calcite was present as cementing material and it was about 15 -30% of the total rock. (author)

Preliminary study on features of mineralogical zoning of epigenetic alteration at sandstone-type uranium deposit, Dongsheng area, Ordos basin

International Nuclear Information System (INIS)

Xiao Xinjian; Li Ziying; Chen Anping

2004-01-01

Sandstone-type uranium deposits located in Dongsheng area, northern Ordos basin, occur in Zhiluo Formation, Middle Jurassic. The Zhiluo Formation is divided into two members. The lower member is further divided into two submembers. The lower submember is dominantly composed of grey sandstone being the ore-hosting horizon; the upper submember consists of grey-green sandstone and mudstone. The upper member of Zhiluo Formation is made of mottled medium-fine grained sandstone and mudstone. Through the microscopic observation and study on sandstones of Zhiluo Formation, authors have established a vertical zonation of epigenetic alteration (from the top to the bottom): the limonitization + clayization + carbonation in the mottled fine-grained sandstone of the upper member of Zhiluo Formation; the green alteration (II) (mainly the chloritization of biotite, as well as the chloritization and epidotization of feldspar) + clayization + carbonation in the grey-green sandstone of the upper submember of the lower member of Zhiluo Formation; and the green alteration (I) (mainly the epidotization of feldspar) + carbonation in grey, grey-white sandstone of the lower submember. The epigenetic alteration basically occurs in grey-green sandstone. The sandstone shows grey-green color because it contains much green biotite (not chlorite). The epigenetic alteration in sandstone layer is closely associated with the uranium ore-formation

Sandstone columns of the 3rd Nile Cataract (Nubia, Northern Sudan)

Czech Academy of Sciences Publication Activity Database

Cílek, Václav; Adamovič, Jiří; Suková, L.

2015-01-01

Roč. 59, Supplement 1 (2015), s. 151-165 ISSN 0372-8854 Grant - others:Program interní podpory projektů mezinárodní spolupráce AV ČR(CZ) M100130902 Institutional support: RVO:67985831 Keywords : Nubian sandstone * columnar jointing * Voronoi fragmentation * 3rd Nile Cataract * Sudan Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.103, year: 2015

Combined rock-physical modelling and seismic inversion techniques for characterisation of stacked sandstone reservoir

NARCIS (Netherlands)

Justiniano, A.; Jaya, Y.; Diephuis, G.; Veenhof, R.; Pringle, T.

2015-01-01

The objective of the study is to characterise the Triassic massive stacked sandstone deposits of the Main Buntsandstein Subgroup at Block Q16 located in the West Netherlands Basin. The characterisation was carried out through combining rock-physics modelling and seismic inversion techniques. The

Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin)

Energy Technology Data Exchange (ETDEWEB)

Dutton, S.P.; Flanders, W.A.; Guzman, J.I.; Zirczy, H.

1999-06-08

The objective of this Class III project is to demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover a higher percentage of the original oil in place through geologically based field development. This year the project focused on reservoir characterization of the East Ford unit, a representative Delaware Mountain Group field that produces from the upper Bell Canyon Formation (Ramsey Sandstone). The field, discovered in 1960, is operated by Orla Petco, Inc., as the East Ford unit; it contained an estimated 19.8 million barrels (MMbbl) of original oil in place. Petrophysical characterization of the East Ford unit was accomplished by integrating core and log data and quantifying petrophysical properties from wireline logs. Most methods of petrophysical analysis that had been developed during an earlier study of the Ford Geraldine unit were successfully transferred to the East Ford unit. The approach that was used to interpret water saturation from resistivity logs, however, had to be modified because in some East Ford wells the log-calculated water saturation was too high and inconsistent with observations made during the actual production. Log-porosity to core-porosity transforms and core-porosity to core-permeability transforms were derived from the East Ford reservoir. The petrophysical data were used to map porosity, permeability, net pay, water saturation, mobil-oil saturation, and other reservoir properties.

Trap architecture of the Early Cretaceous Sarir Sandstone in the eastern Sirt Basin, Libya

Energy Technology Data Exchange (ETDEWEB)

Gras, R. [Schlumberger GeoQuest, Cedex (France); Thusu, B. [Arabian Gulf Oil Company, Benghazi (Libyan Arab Jamahiriya)

1998-12-31

The Sarir Sandstone is the principal reservoir for oil accumulations in the eastern Sirt Basin in Libya. The main phase of the rifting in this area took place in the Late Jurassic-Early Cretaceous, during which time the Sarir Sandstone was deposited as a non-marine, intra-continental clastic syn-rift sequence. Although successfully explored from 1959 onwards, the prolific eastern Sirt Basin is in a relatively immature stage of exploration regarding wildcat drilling and 3D seismic data acquisition. The most recent phase of exploration, utilizing 3D seismic techniques, revealed a complex structural development. The trap geometries are often related to E-W trending, basement-controlled fault systems, oblique to the NNW-SSE Sirt Basin trend. The fault systems were active during the Sarir Sandstone deposition, giving rise to structural as well as combined structural-traps. An increased understanding of trap architecture has led to both re-evaluation of older fields and new discoveries. (author)

Rock Physics and Petrographic Parameters Relationship Within Siliciclastic Rocks: Quartz Sandstone Outcrop Study Case

Science.gov (United States)

Syafriyono, S.; Caesario, D.; Swastika, A.; Adlan, Q.; Syafri, I.; Abdurrokhim, A.; Mardiana, U.; Mohamad, F.; Alfadli, M. K.; Sari, V. M.

2018-03-01

Rock physical parameters value (Vp and Vs) is one of fundamental aspects in reservoir characterization as a tool to detect rock heterogenity. Its response is depend on several reservoir conditions such as lithology, pressure and reservoir fluids. The value of Vp and Vs is controlled by grain contact and contact stiffness, a function of clay mineral content and porosity also affected by mineral composition. The study about Vp and Vs response within sandstone and its relationship with petrographic parameters has become important to define anisotrophy of reservoir characteristics distribution and could give a better understanding about local diagenesis that influence clastic reservoir properties. Petrographic analysis and Vp-Vs calculation was carried out to 12 core sample which is obtained by hand-drilling of the outcrop in Sukabumi area, West Java as a part of Bayah Formation. Data processing and interpretation of sedimentary vertical succession showing that this outcrop comprises of 3 major sandstone layers indicating fluvial depositional environment. As stated before, there are 4 petrographic parameters (sorting, roundness, clay mineral content, and grain contact) which are responsible to the differences of shear wave and compressional wave value in this outcrop. Lithology with poor-sorted and well- roundness has Vp value lower than well-sorted and poor-roundness (sub-angular) grain. For the sample with high clay content, Vp value is ranging from 1681 to 2000 m/s and could be getting high until 2190 to 2714 m/s in low clay content sample even though the presence of clay minerals cannot be defined neither as matrix nor cement. The whole sample have suture grain contact indicating telogenesis regime whereas facies has no relationship with Vp and Vs value because of the different type of facies show similar petrographic parameters after diagenesis.

The Influence of Fold and Fracture Development on Reservoir Behavior of the Lisburne Group of Northern Alaska

Energy Technology Data Exchange (ETDEWEB)

Wallace, Wesley K.; Hanks, Catherine L.; Whalen, Michael T.; Jensen1, Jerry; Shackleton, J. Ryan; Jadamec, Margarete A.; McGee, Michelle M.; Karpov1, Alexandre V.

2001-07-23

The Carboniferous Lisburne Group is a major carbonate reservoir unit in northern Alaska. The lisburne is detachment folded where it is exposed throughout the northeastern Brooks Range, but is relatively underformed in areas of current production in the subsurface of the North Slope. The objectives of this study are to develop a better understanding of four major aspects of the Lisburne: (1) The geometry and kinematics of detachment folds and their truncation by thrust faults, (2) The influence of folding on fracture patterns, (3) The influence of deformation on fluid flow, and (4) Lithostratigraphy and its influence on folding, faulting, fracturing, and reservoir characteristics.

Seasonal effect on trace metal elements behaviour in a reservoir of northern Thailand.

Science.gov (United States)

Grellier, S; Janeau, J L; Thothong, W; Boonsaner, A; Bonnet, M P; Lagane, C; Seyler, P

2013-07-01

Trace metal elements (TME) can be real threats for living organisms. However, few studies dealt with TME in reservoirs in rural areas where farming practises could induce negative effects. Mae Thang reservoir (northern Thailand) has been studied for 3 years to understand the seasonal behaviour of dissolved TME: Fe, Mn, Cd, Al, Pb, V, Cr, Co, Ni, Cu, Zn, Mo, U and As and associated physicochemical parameters. In situ measurements of these parameters were done during the dry and the wet seasons as well as water samples along the water column for further analyses and TME determination by inductively coupled plasma-mass spectrometry (ICP-MS). In the dry season, the water column was characterized by a strong stratification and anoxic conditions in the hypolimnion. High rain and water input from the watershed during the wet season induced mixing of the water. All TME, except Ni, Co and Cr were less concentrated in the wet season indicating a dilution effect by water input. There was thus no important dissolved pollution coming from the watershed. The anoxic conditions in the dry season enhanced the reduction of Fe and Mn and the desorption processes. Depth, and thus oxic-anoxic conditions were the main drivers of TME in the dry season, while in the wet season, dissolution processes from parent rocks of watershed were favoured. The average concentrations of TME in the reservoir were in the limit of the international and Thai standards. Only localized values in the bottom of the reservoir for Fe and Mn were higher than the limits.

Estimated loss of juvenile salmonids to predation by northern squawfish, walleyes, and smallmouth bass in John Day Reservoir, Columbia River

International Nuclear Information System (INIS)

Rieman, B.E.; Beamesderfer, R.C.; Vigg, S.; Poe, T.P.

1991-01-01

The authors estimated the loss of juvenile salmonids Oncorhynchus spp. to predation by northern squawfish Ptychocheilus oregonensis, walleyes Stizostedion vitreum, and smallmouth bass Micropterus dolomieu in John Day Reservoir during 1983-1986. Their estimates were based on measures of daily prey consumption, predator numbers, and numbers of juvenile salmonids entering the reservoir during the April-August period of migration. They estimated the mean annual loss was 2.7 million juvenile salmonids. Northern squawfish were responsible for 78% of the total loss; walleyes accounted for 13% and smallmouth bass for 9%. Twenty-one percent of the loss occurred in a small area immediately below McNary Dam at the head of John Day Reservoir. The authors estimated that the three predator species consumed 14% of all juvenile salmonids that entered the reservoir. Mortality changed by month and increased late in the migration season. Monthly mortality estimates ranged from 7% in June and 61% in August. Mortality from predation was highest for chinook salmon O. tshawytscha, which migrated in July and August. Despite uncertainties in the estimates, it is clear that predation by resident fish predators can easily account for previously explained mortality of out-migrating juvenile salmonids. Alteration of the Columbia River by dams and a decline in the number of salmonids could have increased the fraction of mortality caused by predation over what is was in the past

Research on the calculation method of shale and tuff content: taking tuffaceous reservoirs of X depression in the Hailar–Tamtsag Basin as an example

International Nuclear Information System (INIS)

Liu, Sihui; Huang, Buzhou; Pan, Baozhi; Guo, Yuhang; Fang, Chunhui; Wang, Guiping; Sun, Fengxian; Qiu, Haibo; Jiang, Bici

2015-01-01

Shale content is known in reservoir evaluation as an important parameter in well logging. However, the log response characteristics are simultaneously affected by shale and tuff existing in tuffaceous sandstone reservoirs. Due to the fact that tuff content exerts an influence on the calculation of shale content, the former is equally important as the latter. Owing to the differences in the source and composition between shale and tuff, the calculation of tuff content using the same methods for shale content cannot meet the accuracy requirements of logging evaluation. The present study takes the tuffaceous reservoirs in the X depression of the Hailar–Tamtsag Basin as an example. The differences in the log response characteristics between shale and tuff are theoretically analyzed and verified using core analysis data. The tuff is then divided into fine- and coarse-grained fractions, according to the differences in the distribution of the radioactive elements, uranium, thorium and potassium. Next, a volume model suitable for tuffaceous sandstone reservoirs is established to include a sandstone matrix, shale, fine-grained tuff, coarse-grained tuff and pore. A comparison of three optimization algorithms shows that the particle swarm optimization (PSO) yields better calculation results with small mean errors. The resistivity differences among shale, fine-grained tuff and coarse-grained tuff are considered in the calculation of saturation. The water saturation of tuffaceous reservoirs is computed using the improved Poupon’s equation, which is suitable for tuffaceous sandstone reservoirs with low water salinity. The method is used in well Y, and is shown to have a good application effect. (paper)

THE OHIO RIVER VALLEY CO2 STORAGE PROJECT - PRELIMINARY ASSESSMENT OF DEEP SALINE RESERVOIRS AND COAL SEAMS

Energy Technology Data Exchange (ETDEWEB)

Michael J. Mudd; Howard Johnson; Charles Christopher; T.S. Ramakrishnan, Ph.D.

2003-08-01

This report describes the geologic setting for the Deep Saline Reservoirs and Coal Seams in the Ohio River Valley CO{sub 2} Storage Project area. The object of the current project is to site and design a CO{sub 2} injection facility. A location near New Haven, WV, has been selected for the project. To assess geologic storage reservoirs at the site, regional and site-specific geology were reviewed. Geologic reports, deep well logs, hydraulic tests, and geologic maps were reviewed for the area. Only one well within 25 miles of the site penetrates the deeper sedimentary rocks, so there is a large amount of uncertainty regarding the deep geology at the site. New Haven is located along the Ohio River on the border of West Virginia and Ohio. Topography in the area is flat in the river valley but rugged away from the Ohio River floodplain. The Ohio River Valley incises 50-100 ft into bedrock in the area. The area of interest lies within the Appalachian Plateau, on the western edge of the Appalachian Mountain chain. Within the Appalachian Basin, sedimentary rocks are 3,000 to 20,000 ft deep and slope toward the southeast. The rock formations consist of alternating layers of shale, limestone, dolomite, and sandstone overlying dense metamorphic continental shield rocks. The Rome Trough is the major structural feature in the area, and there may be some faults associated with the trough in the Ohio-West Virginia Hinge Zone. The area has a low earthquake hazard with few historical earthquakes. Target injection reservoirs include the basal sandstone/Lower Maryville and the Rose Run Sandstone. The basal sandstone is an informal name for sandstones that overlie metamorphic shield rock. Regional geology indicates that the unit is at a depth of approximately 9,100 ft below the surface at the project site and associated with the Maryville Formation. Overall thickness appears to be 50-100 ft. The Rose Run Sandstone is another potential reservoir. The unit is located approximately 1

Sequence stratigraphic and sedimentologic significance of biogenic structures from a late Paleozoic marginal- to open-marine reservoir, Morrow Sandstone, subsurface of southwest Kansas, USA

Science.gov (United States)

Buatois, L.A.; Mangano, M.G.; Alissa, A.; Carr, T.R.

2002-01-01

Integrated ichnologic, sedimentologic, and stratigraphic studies of cores and well logs from Lower Pennsylvanian oil and gas reservoirs (lower Morrow Sandstone, southwest Kansas) allow distinction between fluvio-estuarine and open marine deposits in the Gentzler and Arroyo fields. The fluvio-estuarine facies assemblage is composed of both interfluve and valley-fill deposits, encompassing a variety of depositional environments such as fluvial channel, interfluve paleosol, bay head delta, estuary bay, restricted tidal flat, intertidal channel, and estuary mouth. Deposition in a brackish-water estuarine valley is supported by the presence of a low diversity, opportunistic, impoverished marine ichnofaunal assemblage dominated by infaunal structures, representing an example of a mixed, depauperate Cruziana and Skolithos ichnofacies. Overall distribution of ichnofossils along the estuarine valley was mainly controlled by the salinity gradient, with other parameters, such as oxygenation, substrate and energy, acting at a more local scale. The lower Morrow estuarine system displays the classical tripartite division of wave-dominated estuaries (i.e. seaward-marine sand plug, fine-grained central bay, and sandy landward zone), but tidal action is also recorded. The estuarine valley displays a northwest-southeast trend, draining to the open sea in the southeast. Recognition of valley-fill sandstones in the lower Morrow has implications for reservoir characterization. While the open marine model predicts a "layer-cake" style of facies distribution as a consequence of strandline shoreline progradation, identification of valley-fill sequences points to more compartmentalized reservoirs, due to the heterogeneity created by valley incision and subsequent infill. The open-marine facies assemblage comprises upper, middle, and lower shoreface; offshore transition; offshore; and shelf deposits. In contrast to the estuarine assemblage, open marine ichnofaunas are characterized by a

Reservoir engineering assessment of Dubti geothermal field, Northern Tendaho Rift, Ethiopia

Energy Technology Data Exchange (ETDEWEB)

Battistelli, A.; Ferragina, C. [Aquater S.p.A. (ENI Group), San Lorenzo in Campo (Italy); Yiheyis, A.; Abatneh, W. [Ethiopian Institute of Geological Surveys, Addis Ababa (Ethiopia); Calore, C. [International Institute for Geothermal Research, Pisa (Italy)

2002-06-01

Following on from surface exploration surveys performed during the 1970s and early 1980s, exploration drilling was carried out in the Tendaho Rift, in Central Afar (Ethiopia), from October 1993 to June 1995. Three deep and one shallow well were drilled in the central part of the Northern Tendaho Rift to verify the existence of a geothermal reservoir and its possible utilisation for electric power generation. The project was jointly financed by the Ethiopian Ministry of Mines and Energy and the Italian Ministry for Foreign Affairs. Project activities were performed by the Ethiopian Institute of Geological Surveys and Aquater SpA. The main reservoir engineering data discussed in this paper were collected during drilling and testing of the above four wells, three of which are located inside the Dubti Cotton Plantation, in which a promising hydrothermal area was identified by surface exploration surveys. Drilling confirmed the existence of a liquid-dominated shallow reservoir inside the Dubti Plantation, characterised by a boiling -point-for-depth temperature distribution down to about 500 m depth. The main permeable zones in the Sedimentary Sequence, which is made up of lacustrine deposits, are located in correspondence to basalt lava flow interlayerings, or at the contact between volcanic and sedimentary rocks. At depth, the basaltic lava flows that characterise the Afar Stratoid Series seem to have low permeability, with the exception of fractured zones associated with sub-vertical faults. Two different upflows of geothermal fluids have been inferred: one flow connected to the Dubti fault feeds the shallow reservoir crossed by wells TD-2 and TD-4, where a maximum temperature of 245{sup o}C was recorded; the second flow seems to be connected with a fault located east of well TD-1, where the maximum recorded temperature was 270{sup o}C. A schematic conceptual model of the Dubti hydrothermal area, as derived from reservoir engineering studies integrated with geological

A preliminary analysis and assessment of hydrogeological conditions for in-situ leach mining of sandstone-type uranium deposit in northern Ordos basin

International Nuclear Information System (INIS)

Chen Fazheng; Zhao Jinfeng; Chang Baocheng; Gao Junyi

2006-01-01

A systematic analysis and assessment on hydrogeologic condition, the lithology and hydrogeologic structure of ore-hosting aquitfers, hydrodynamic condition, hydrochemical characteristics at a sandstone-type uranium deposit in northern Ordos basin is made in this paper. It has been concluded, that hydrogeologic condition in the study area is favorable, meeting the requirements for in-situ leach mining of the deposit. Aimed at the low artesian pressure head and low water output and based on the results of pumping-injection tests which led to the significant increase of water output, a technical scheme of pressured water injection has been proposed to artificially raise the artesian pressure head and increase the output of groundwater to satisfy the requirements of in-situ leach mining. (authors)

Forecasting of reservoir pressures of oil and gas bearing complexes in northern part of West Siberia for safety oil and gas deposits exploration and development

Science.gov (United States)

Gorbunov, P. A.; Vorobyov, S. V.

2017-10-01

In the paper the features of reservoir pressures changes in the northern part of West Siberian oil-and gas province are described. This research is based on the results of hydrodynamic studies in prospecting and explorating wells in Yamal-Nenets Autonomous District. In the Cenomanian, Albian, Aptian and in the top of Neocomian deposits, according to the research, reservoir pressure is usually equal to hydrostatic pressure. At the bottom of the Neocomian and Jurassic deposits zones with abnormally high reservoir pressures (AHRP) are distinguished within Gydan and Yamal Peninsula and in the Nadym-Pur-Taz interfluve. Authors performed the unique zoning of the territory of the Yamal-Nenets Autonomous District according to the patterns of changes of reservoir pressures in the section of the sedimentary cover. The performed zoning and structural modeling allow authors to create a set of the initial reservoir pressures maps for the main oil and gas bearing complexes of the northern part of West Siberia. The results of the survey should improve the efficiency of exploration drilling by preventing complications and accidents during this operation in zones with abnormally high reservoir pressures. In addition, the results of the study can be used to estimate gas resources within prospective areas of Yamal-Nenets Autonomous District.

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Finch, W.I.; Davis, J.F.

1985-01-01

World-class sandstone-type uranium deposits are defined as epigenetic concentrations of uranium minerals occurring as uneven impregnations and minor massive replacements primarily in fluvial, lacustrine, and deltaic sandstone formations. The main purpose of this introductory paper is to define, classify, and introduce to the general geologic setting for sandstone-type uranium deposits

Characterization of oil and gas reservoir heterogeneity. Final report

Energy Technology Data Exchange (ETDEWEB)

Tyler, N.; Barton, M.D.; Bebout, D.G.; Fisher, R.S.; Grigsby, J.D.; Guevara, E.; Holtz, M.; Kerans, C.; Nance, H.S.; Levey, R.A.

1992-10-01

Research described In this report addresses the internal architecture of two specific reservoir types: restricted-platform carbonates and fluvial-deltaic sandstones. Together, these two reservoir types contain more than two-thirds of the unrecovered mobile oil remaining ill Texas. The approach followed in this study was to develop a strong understanding of the styles of heterogeneity of these reservoir types based on a detailed outcrop description and a translation of these findings into optimized recovery strategies in select subsurface analogs. Research targeted Grayburg Formation restricted-platform carbonate outcrops along the Algerita Escarpment and In Stone Canyon In southeastern New Mexico and Ferron deltaic sandstones in central Utah as analogs for the North Foster (Grayburg) and Lake Creek (Wilcox) units, respectively. In both settings, sequence-stratigraphic style profoundly influenced between-well architectural fabric and permeability structure. It is concluded that reservoirs of different depositional origins can therefore be categorized Into a ``heterogeneity matrix`` based on varying intensity of vertical and lateral heterogeneity. The utility of the matrix is that it allows prediction of the nature and location of remaining mobile oil. Highly stratified reservoirs such as the Grayburg, for example, will contain a large proportion of vertically bypassed oil; thus, an appropriate recovery strategy will be waterflood optimization and profile modification. Laterally heterogeneous reservoirs such as deltaic distributary systems would benefit from targeted infill drilling (possibly with horizontal wells) and improved areal sweep efficiency. Potential for advanced recovery of remaining mobile oil through heterogeneity-based advanced secondary recovery strategies In Texas is projected to be an Incremental 16 Bbbl. In the Lower 48 States this target may be as much as 45 Bbbl at low to moderate oil prices over the near- to mid-term.

Improved prediction of reservoir behavior through integration of quantitative geological and petrophysical data

Energy Technology Data Exchange (ETDEWEB)

Auman, J. B.; Davies, D. K.; Vessell, R. K.

1997-08-01

Methodology that promises improved reservoir characterization and prediction of permeability, production and injection behavior during primary and enhanced recovery operations was demonstrated. The method is based on identifying intervals of unique pore geometry by a combination of image analysis techniques and traditional petrophysical measurements to calculate rock type and estimate permeability and saturation. Results from a complex carbonate and sandstone reservoir were presented as illustrative examples of the versatility and high level of accuracy of this method in predicting reservoir quality. 16 refs., 5 tabs., 14 figs.

Producing Light Oil from a Frozen Reservoir: Reservoir and Fluid Characterization of Umiat Field, National Petroleum Reserve, Alaska

Energy Technology Data Exchange (ETDEWEB)

Hanks, Catherine

2012-12-31

Umiat oil field is a light oil in a shallow, frozen reservoir in the Brooks Range foothills of northern Alaska with estimated oil-in-place of over 1 billion barrels. Umiat field was discovered in the 1940’s but was never considered viable because it is shallow, in the permafrost, and far from any transportation infrastructure. The advent of modern drilling and production techniques has made Umiat and similar fields in northern Alaska attractive exploration and production targets. Since 2008 UAF has been working with Renaissance Alaska Inc. and, more recently, Linc Energy, to develop a more robust reservoir model that can be combined with rock and fluid property data to simulate potential production techniques. This work will be used to by Linc Energy as they prepare to drill up to 5 horizontal wells during the 2012-2013 drilling season. This new work identified three potential reservoir horizons within the Cretaceous Nanushuk Formation: the Upper and Lower Grandstand sands, and the overlying Ninuluk sand, with the Lower Grandstand considered the primary target. Seals are provided by thick interlayered shales. Reserve estimates for the Lower Grandstand alone range from 739 million barrels to 2437 million barrels, with an average of 1527 million bbls. Reservoir simulations predict that cold gas injection from a wagon-wheel pattern of multilateral injectors and producers located on 5 drill sites on the crest of the structure will yield 12-15% recovery, with actual recovery depending upon the injection pressure used, the actual Kv/Kh encountered, and other geologic factors. Key to understanding the flow behavior of the Umiat reservoir is determining the permeability structure of the sands. Sandstones of the Cretaceous Nanushuk Formation consist of mixed shoreface and deltaic sandstones and mudstones. A core-based study of the sedimentary facies of these sands combined with outcrop observations identified six distinct facies associations with distinctive permeability

GREYBULL SANDSTONE PETROLEUM POTENTIAL ON THE CROW INDIAN RESERVATION, SOUTH-CENTRAL MONTANA

Energy Technology Data Exchange (ETDEWEB)

David A. Lopez

2000-12-14

. With continued transgression, the Greybull fluvial sand graded upward into marginal marine (probably estuarine) sand (upper Greybull) and finally was capped by marine shale and the Fall River Sandstone. Subsurface mapping, incorporated with surface data, has revealed five major Greybull channels crossing the Crow Reservation. The Greybull Sandstone is a proven petroleum reservoir in the Crow Reservation region. Greybull combination traps require the presence of channel sandstone as well as structural closure. With sparse reservation well control, subsurface structural and isopach maps are highly interpretive. Three potential Greybull exploration leads were identified where possible structural closures are coincident with mapped Greybull channels: the Little Woody, Woody Dome, and Crow Agency prospects. Of these, the Crow Agency prospect was confirmed by a significant soil-gas anomaly and appears to have the greatest probability of having trapped a hydrocarbon accumulation.

Morphology of channels and channel-sand bodies in the Glauconitic sandstone member (Upper Mannville), Little Bow area, Alberta

Energy Technology Data Exchange (ETDEWEB)

Hopkins, J.C.; Hermanson, S.W.; Lawton, D.C.

1982-12-01

Large channels in the Glauconitic sandstone member of southern Alberta have proved to be difficult exploration targets because of an irregular distribution of reservoir sands within the channels. In the Little Bow area, two channels are present in the lower part of the Glauconitic member and have cut into the underlying Calcareous member. The channels can be recognized where they truncate regional markers of the Calcareous member -- the Bantry shale and Ostracod limestone, and where channel-fill deposits exhibit uniform geophysical log characters, indicating sandstone- or mudstone-filled reaches. Sediments of the Glauconitic member adjacent to the channels comprise a series of splay sandstones and mudstones that prograded into interdistributary bays of the lower delta plain. The two channels associated with these deposits are interpreted as distributary channels. Sand bodies within the channels formed as lateral bars and are isolated by mudstones which mark the abandoned stream course. Geological exploration for these discontinuous channel sandstones is difficult, and high-resolutio seismic data integrated with sound geologic modelling are critical for successful prospect delineation.

Experimental Study on the Effects of Stress Variations on the Permeability of Feldspar-Quartz Sandstone

Directory of Open Access Journals (Sweden)

Fugang Wang

2017-01-01

Full Text Available The multistage and discontinuous nature of the injection process used in the geological storage of CO2 causes reservoirs to experience repeated loading and unloading. The reservoir permeability changes caused by this phenomenon directly impact the CO2 injection process and the process of CO2 migration in the reservoirs. Through laboratory experiments, variations in the permeability of sandstone in the Liujiagou formation of the Ordos CO2 capture and storage (CCS demonstration project were analyzed using cyclic variations in injection pressure and confining pressure and multistage loading and unloading. The variation in the micropore structure and its influence on the permeability were analyzed based on micropore structure tests. In addition, the effects of multiple stress changes on the permeability of the same type of rock with different clay minerals content were also analyzed. More attention should be devoted to the influence of pressure variations on permeability in evaluations of storage potential and studies of CO2 migration in reservoirs in CCS engineering.

CarbonSAFE Rocky Mountain Phase I : Seismic Characterization of the Navajo Reservoir, Buzzard Bench, Utah

Science.gov (United States)

Haar, K. K.; Balch, R. S.; Lee, S. Y.

2017-12-01

The CarbonSAFE Rocky Mountain project team is in the initial phase of investigating the regulatory, financial and technical feasibility of commercial-scale CO2 capture and storage from two coal-fired power plants in the northwest region of the San Rafael Swell, Utah. The reservoir interval is the Jurassic Navajo Sandstone, an eolian dune deposit that at present serves as the salt water disposal reservoir for Ferron Sandstone coal-bed methane production in the Drunkards Wash field and Buzzard Bench area of central Utah. In the study area the Navajo sandstone is approximately 525 feet thick and is at an average depth of about 7000 feet below the surface. If sufficient porosity and permeability exist, reservoir depth and thickness would provide storage for up to 100,000 metric tonnes of CO2 per square mile, based on preliminary estimates. This reservoir has the potential to meet the DOE's requirement of having the ability to store at least 50 million metric tons of CO2 and fulfills the DOE's initiative to develop protocols for commercially sequestering carbon sourced from coal-fired power plants. A successful carbon storage project requires thorough structural and stratigraphic characterization of the reservoir, seal and faults, thereby allowing the creation of a comprehensive geologic model with subsequent simulations to evaluate CO2/brine migration and long-term effects. Target formation lithofacies and subfacies data gathered from outcrop mapping and laboratory analysis of core samples were developed into a geologic model. Synthetic seismic was modeled from this, allowing us to seismically characterize the lithofacies of the target formation. This seismic characterization data was then employed in the interpretation of 2D legacy lines which provided stratigraphic and structural control for more accurate model development of the northwest region of the San Rafael Swell. Developing baseline interpretations such as this are crucial toward long-term carbon storage

A systematic procedure for reservoir characterization: Annual report for the period October 1, 1985-September 30, 1986

Energy Technology Data Exchange (ETDEWEB)

Lake, L.W.; Kocurek, G.A.; Miller, M.A.

1987-12-01

This report deals with a variety of topics all centered around the main goal of making numerical reservoir simulation results conform more closely with geologic descriptions. The first part of the report discusses results on conditional simulations of miscible displacements in randomly heterogeneous permeable media. The focus here is on local or macroscopic dispersion, the dispersion experienced at a fixed point in the medium. Macroscopic dispersivity has many of the same dependencies on reservoir properties as does megascopic dispersivity, but it seems to be less time dependent and is always smaller. We have not discovered a mathematical model to describe its behavior. A major portion of the report deals with statistical descriptions. We investigate the bias and precision of standard measures of heterogeneity, the Lorenz and Dykstra-Parsons coefficient. After this, the work explores the benefits of using a distribution type characterization parameter in exploring heterogeneity. The final major protion of the report describes our mapping efforts on the Page sandstone outcrop in northern Arizona. The mapping is to be used in generating both deterministic descriptions and in calibrating the stochastic descriptions discussed above. 128 refs., 95 figs., 10 tabs.

Method for detecting and locating sand-producing zones in friable, unconsolidated sandstone formations of subterranean formations

International Nuclear Information System (INIS)

Sparlin, D.D.

1976-01-01

A sand-producing zone in a friable, unconsolidated sandstone formation traversed by a well bore is found by first introducing into the reservoir about 0.1--10 gallons of a radioactive mixture per foot of vertical formation being treated, the mixture containing about 0.1--1 lb of radioactive material per gallon of carrier fluid. A dispersing agent containing a deemulsifying surfactant may then be injected into the formation. The radioactivity in the well bore is recorded and the reservoir is returned to production. Another radioactivity log is run and a decrease in radioactivity indicates the location of the sand-producing portions of the formation

CO2-induced mechanical behaviour of Hawkesbury sandstone in the Gosford basin: An experimental study

International Nuclear Information System (INIS)

Rathnaweera, T.D.; Ranjith, P.G.; Perera, M.S.A.; Haque, A.; Lashin, A.; Al Arifi, N.; Chandrasekharam, D; Yang, SQ; Xu, T; Wang, SH; Yasar, E

2015-01-01

Carbon dioxide (CO 2 ) sequestered in saline aquifers undergoes a variety of chemically-coupled mechanical effects, which may cause CO 2 -induced mechanical changes and time-dependent reservoir deformation. This paper investigates the mineralogical and microstructural changes that occur in reservoir rocks following injection of CO 2 in deep saline aquifers and the manner in which these changes influence the mechanical properties of the reservoir rocks. In this study, cylindrical sandstone specimens, 38 mm in diameter and 76 mm high, obtained from the Gosford basin, were used to perform a series of unconfined compressive strength (UCS) tests. Different saturation conditions: dry, water- and brine-saturated sandstone samples with and without scCO 2 (super-critical carbon dioxide) injection, were considered in the study to obtain a comprehensive understanding of the impact of scCO 2 injection during the CO 2 sequestration process on saline aquifer mechanical properties. An acoustic emission (AE) system was employed to identify the stress threshold values of crack closure, crack initiation and crack damage for each testing condition during the whole deformation process of the specimens. Finally, scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray fluorescence (XRF) analyses were performed to evaluate the chemical and mineralogical changes that occur in reservoir rocks during CO 2 injection. From the test results, it is clear that the CO 2 -saturated samples possessed a lower peak strength compared to non-CO 2 saturated samples. According to SEM, XRD and XRF analyses, considerable quartz mineral corrosion and dissolution of calcite and siderite were observed during the interactions of the CO 2 /water/rock and CO 2 /brine/rock systems, which implies that mineralogical and geochemical rock alterations affect rock mechanical properties by accelerating the collapse mechanisms of the pore matrix. AE results also reveal the weakening effect of rock pore

The Bakken - An Unconventional Petroleum and Reservoir System

Energy Technology Data Exchange (ETDEWEB)

Sarg, J.

2011-12-31

An integrated geologic and geophysical study of the Bakken Petroleum System, in the Williston basin of North Dakota and Montana indicates that: (1) dolomite is needed for good reservoir performance in the Middle Bakken; (2) regional and local fractures play a significant role in enhancing permeability and well production, and it is important to recognize both because local fractures will dominate in on-structure locations; and (3) the organic-rich Bakken shale serves as both a source and reservoir rock. The Middle Bakken Member of the Bakken Formation is the target for horizontal drilling. The mineralogy across all the Middle Bakken lithofacies is very similar and is dominated by dolomite, calcite, and quartz. This Member is comprised of six lithofacies: (A) muddy lime wackestone, (B) bioturbated, argillaceous, calcareous, very fine-grained siltstone/sandstone, (C) planar to symmetrically ripple to undulose laminated, shaly, very fine-grained siltstone/sandstone, (D) contorted to massive fine-grained sandstone, to low angle, planar cross-laminated sandstone with thin discontinuous shale laminations, (E) finely inter-laminated, bioturbated, dolomitic mudstone and dolomitic siltstone/sandstone to calcitic, whole fossil, dolomitic lime wackestone, and (F) bioturbated, shaly, dolomitic siltstone. Lithofacies B, C, D, and E can all be reservoirs, if quartz and dolomite-rich (facies D) or dolomitized (facies B, C, E). Porosity averages 4-8%, permeability averages 0.001-0.01 mD or less. Dolomitic facies porosity is intercrystalline and tends to be greater than 6%. Permeability may reach values of 0.15 mD or greater. This appears to be a determinant of high productive wells in Elm Coulee, Parshall, and Sanish fields. Lithofacies G is organic-rich, pyritic brown/black mudstone and comprises the Bakken shales. These shales are siliceous, which increases brittleness and enhances fracture potential. Mechanical properties of the Bakken reveal that the shales have similar

Anisotropy of sandstone reservoir and shale overburden estimated from spherical sample measurements and cross-dipole logging

Czech Academy of Sciences Publication Activity Database

Lokajíček, Tomáš; Brajanovski, M.; Gurevich, B.; Bona, A.; Nadri, D.; Urosevic, M.; Duncan, G.

2009-01-01

Roč. 11, - (2009), s. 4956-4956 ISSN 1029-7006. [European Geosciences Union General Assembly. 19.04.2009-24.04.2009, Vienna] R&D Projects: GA ČR GA205/08/0676 Institutional research plan: CEZ:AV0Z30130516 Keywords : anisotropy * sandstones * rocks Subject RIV: DB - Geology ; Mineralogy

Digitization of uranium deposit information in basin. A new strategy of ISL sandstone-type uranium deposits exploration

International Nuclear Information System (INIS)

Tan Chenglong

2006-01-01

The discovered ISL sandstone-type uranium deposits in the entire world are mostly blind deposits, many of them occur in bleak desert, gobi desert, and semi-hilly land area. Exploration methods for these deposits mainly depend on great and systematic drilling. There are many large-medium size Meso-Cenozoic sedimentary basins in northern China, and over twenty of them are thick overburden basins which are mostly the virgin land for ISL sandstone-type uranium deposit. Due to the comprehensive national power, geological background, uranium exploration ability, great and systematic drilling is not favorable for prospecting ISL sandstone-type uranium deposit in China. According to the exploration and prospecting experiences for mineral ore bodies at home and abroad, uranium information mapping based on geochemical survey of the basins is a new strategy for ISL sandstone-type uranium deposits. It is an economic, practical, fast and effective method, and has been manifested by the performing information digitization for oil and gas resources, gold mineral resources in China and the mapping of uranium information for whole Europe continent. (authors)

Advanced Reservoir Characterization and Development through High-Resolution 3C3D Seismic and Horizontal Drilling: Eva South Marrow Sand Unit, Texas County, Oklahoma

Energy Technology Data Exchange (ETDEWEB)

Wheeler,David M.; Miller, William A.; Wilson, Travis C.

2002-03-11

The Eva South Morrow Sand Unit is located in western Texas County, Oklahoma. The field produces from an upper Morrow sandstone, termed the Eva sandstone, deposited in a transgressive valley-fill sequence. The field is defined as a combination structural stratigraphic trap; the reservoir lies in a convex up -dip bend in the valley and is truncated on the west side by the Teepee Creek fault. Although the field has been a successful waterflood since 1993, reservoir heterogeneity and compartmentalization has impeded overall sweep efficiency. A 4.25 square mile high-resolution, three component three-dimensional (3C3D) seismic survey was acquired in order to improve reservoir characterization and pinpoint the optimal location of a new horizontal producing well, the ESU 13-H.

Sandstone-type uranium deposits

International Nuclear Information System (INIS)

Austin, S.R.; D'Andrea, R.F. Jr.

1978-01-01

Three overall factors are necessary for formation of uranium deposits in sandstone: a source of uranium, host rocks capable of transmitting uranium-bearing solutions, and a precipitant. Possible sources of uranium in sandstone-type deposits include groundwaters emanating from granitic highlands, arkosic sediments, tuffaceous material within or overlying the host rocks, connate fluids, and overlying black shales. The first three sources are considered the most likely. Host rocks are generally immature sandstones deposited in alluvial-fan, intermontane-basin or marginal-marine environments, but uranium deposits do occur in well-winnowed barrier-bar or eolian sands. Host rocks for uranium deposits generally show coefficients of permeability on the order of 1 to 100 gal/day/ft 2 . Precipitants are normally agents capable of reducing uranium from the uranyl to the uranous state. The association of uranium with organic matter is unequivocal; H 2 S, a powerful reductant, may have been present at the time of formation of some deposits but may go unnoticed today. Vanadium can serve to preserve the tabular characteristics of some deposits in the near-surface environment, but is considered an unlikely primary precipitant for uranium. Uranium deposits in sandstone are divided into two overall types: peneconcordant deposits, which occur in locally reducing environments in otherwise oxidized sandstones; and roll-type deposits, which occur at the margin of an area where an oxidized groundwater has permeated an otherwise reduced sandstone. Uranium deposits are further broken down into four subclasses; these are described

Understanding CO2 Plume Behavior and Basin-Scale Pressure Changes during Sequestration Projects through the use of Reservoir Fluid Modeling

Science.gov (United States)

Leetaru, H.E.; Frailey, S.M.; Damico, J.; Mehnert, E.; Birkholzer, J.; Zhou, Q.; Jordan, P.D.

2009-01-01

Large scale geologic sequestration tests are in the planning stages around the world. The liability and safety issues of the migration of CO2 away from the primary injection site and/or reservoir are of significant concerns for these sequestration tests. Reservoir models for simulating single or multi-phase fluid flow are used to understand the migration of CO2 in the subsurface. These models can also help evaluate concerns related to brine migration and basin-scale pressure increases that occur due to the injection of additional fluid volumes into the subsurface. The current paper presents different modeling examples addressing these issues, ranging from simple geometric models to more complex reservoir fluid models with single-site and basin-scale applications. Simple geometric models assuming a homogeneous geologic reservoir and piston-like displacement have been used for understanding pressure changes and fluid migration around each CO2 storage site. These geometric models are useful only as broad approximations because they do not account for the variation in porosity, permeability, asymmetry of the reservoir, and dip of the beds. In addition, these simple models are not capable of predicting the interference between different injection sites within the same reservoir. A more realistic model of CO2 plume behavior can be produced using reservoir fluid models. Reservoir simulation of natural gas storage reservoirs in the Illinois Basin Cambrian-age Mt. Simon Sandstone suggest that reservoir heterogeneity will be an important factor for evaluating storage capacity. The Mt. Simon Sandstone is a thick sandstone that underlies many significant coal fired power plants (emitting at least 1 million tonnes per year) in the midwestern United States including the states of Illinois, Indiana, Kentucky, Michigan, and Ohio. The initial commercial sequestration sites are expected to inject 1 to 2 million tonnes of CO2 per year. Depending on the geologic structure and

Seasonal Deep Aquifer Thermal Energy Storage in the Gassum Sandstone Formation

DEFF Research Database (Denmark)

Holmslykke, H.D.H.; Kjøller, C.; Fabricius, Ida Lykke

Seasonal storage of excess heat in hot deep aquifers is considered to optimise the usage of commonly available energy sources. The potential chemical reactions caused by heating the Gassum Sandstone Formation to up to 150°C is investigated by core flooding experiments combined with petrographic...... analysis and geochemical modelling. Synthetic formation water is injected into two sets of Gassum Formation samples at 25°C, 50°C (reservoir temperature), 100°C and 150°C with a velocity of 0.05 PV/hr and 0.1 PV/hr, respectively. A significant increase in the aqueous concentration of silicium and iron...

IMPROVING CO2 EFFICIENCY FOR RECOVERING OIL IN HETEROGENEOUS RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Reid B. Grigg; Robert K. Svec; Zhengwen Zeng; Baojun Bai; Yi Liu

2004-09-27

The third annual report of ''Improving CO{sub 2} Efficiency for Recovery Oil in Heterogeneous Reservoirs'' presents results of laboratory studies with related analytical models for improved oil recovery. All studies were designed to optimize utilization and extend the practice of CO{sub 2} flooding to a wider range of reservoirs. Chapter 1 describes the behavior at low concentrations of the surfactant Chaser International CD1045{trademark} (CD) versus different salinity, pressure and temperature. Results of studies on the effects of pH and polymer (hydrolyzed polyacrylamide?HPAM) and CO{sub 2} foam stability after adsorption in the core are also reported. Calcium lignosulfonate (CLS) transport mechanisms through sandstone, description of the adsorption of CD and CD/CLS onto three porous media (sandstone, limestone and dolomite) and five minerals, and the effect of adsorption on foam stability are also reported. In Chapter 2, the adsorption kinetics of CLS in porous Berea sandstone and non-porous minerals are compared by monitoring adsorption density change with time. Results show that adsorption requires a much longer time for the porous versus non-porous medium. CLS adsorption onto sandstone can be divided into three regions: adsorption controlled by dispersion, adsorption controlled by diffusion and adsorption equilibrium. NaI tracer used to characterize the sandstone had similar trends to earlier results for the CLS desorption process, suggesting a dual porosity model to simulate flow through Berea sandstone. The kinetics and equilibrium test for CD adsorption onto five non-porous minerals and three porous media are reported in Chapter 3. CD adsorption and desorption onto non-porous minerals can be established in less than one hour with adsorption densities ranging from 0.4 to 1.2 mg of CD per g of mineral in decreasing order of montmorillonite, dolomite, kaolinite, silica and calcite. The surfactant adsorption onto three porous media takes

Analysis of Critical Permeabilty, Capillary Pressure and Electrical Properties for Mesaverde Tight Gas Sandstones from Western U.S. Basins

Energy Technology Data Exchange (ETDEWEB)

Alan Byrnes; Robert Cluff; John Webb; John Victorine; Ken Stalder; Daniel Osburn; Andrew Knoderer; Owen Metheny; Troy Hommertzheim; Joshua Byrnes; Daniel Krygowski; Stefani Whittaker

2008-06-30

Although prediction of future natural gas supply is complicated by uncertainty in such variables as demand, liquefied natural gas supply price and availability, coalbed methane and gas shale development rate, and pipeline availability, all U.S. Energy Information Administration gas supply estimates to date have predicted that Unconventional gas sources will be the dominant source of U.S. natural gas supply for at least the next two decades (Fig. 1.1; the period of estimation). Among the Unconventional gas supply sources, Tight Gas Sandstones (TGS) will represent 50-70% of the Unconventional gas supply in this time period (Fig. 1.2). Rocky Mountain TGS are estimated to be approximately 70% of the total TGS resource base (USEIA, 2005) and the Mesaverde Group (Mesaverde) sandstones represent the principal gas productive sandstone unit in the largest Western U.S. TGS basins including the basins that are the focus of this study (Washakie, Uinta, Piceance, northern Greater Green River, Wind River, Powder River). Industry assessment of the regional gas resource, projection of future gas supply, and exploration programs require an understanding of reservoir properties and accurate tools for formation evaluation. The goal of this study is to provide petrophysical formation evaluation tools related to relative permeability, capillary pressure, electrical properties and algorithms for wireline log analysis. Detailed and accurate moveable gas-in-place resource assessment is most critical in marginal gas plays and there is need for quantitative tools for definition of limits on gas producibility due to technology and rock physics and for defining water saturation. The results of this study address fundamental questions concerning: (1) gas storage; (2) gas flow; (3) capillary pressure; (4) electrical properties; (5) facies and upscaling issues; (6) wireline log interpretation algorithms; and (7) providing a web-accessible database of advanced rock properties. The following text

Emplacement processes of tuffaceous sandstones at IODP Site C0011B, Nankai Trough, derived from modal analysis

Science.gov (United States)

Schindlbeck, J. C.; Kutterolf, S.; Freundt, A.

2011-12-01

Tuffaceous sandstones are characterized by their high amount (25 to 75%) of pyroclasts in their modal composition. During IODP Expedition 322 three interbeds of tuffaceous sandstones have been found within a moderately lithified and bioturbated silty claystone sequence in the late Miocene (>7.07 to ~9.0 Ma) upper part of the middle Shikoku Basin facies. Of the three sandstones, units 1 and 2 are single beds whereas unit 3 is composed of three beds. Modal analyses of 29 sandstone thin sections reveal systematic vertical changes within each bed. Generally low-density pyroclasts are enriched at the top (50-60 vol%) of each sandstone bed whereas dense lithic components (25-30 vol%) and minerals (25-30 vol%) are enriched at the bottom. The vertically varying abundance of various types of lithic fragments (sedimentary, volcanoclastic and metamorphic) suggests that these have also been segregated according to their respective densities. The highest amount of fine-grained matrix glass is found in the middle of each bed. Pumice and lithic fragments in the middle and upper parts of the sandstone beds carry ash coatings. For sandstone package 3, in contrast to 1 and 2, core pictures and thin section analyses indicate a subdivision in three units showing the same significant variations in top to bottom enrichment. This suggests three sedimentation events following each other in short time intervals. Glass and mineral chemistry of each sandstone bed show no significant vertical variations. Specifically the matrix glass-shard major element compositions are identical to the pumice clast composition in each tuffaceous sandstone bed. The compositions of amphibole and pyroxene crystals differ only slightly between the sandstone packages. Application of the Ridolfi et al. (2009) thermobarometric calculations to amphiboles of sandstone packages 1 and 2 suggests that each of these was derived from a volcanic system comprising both a deep and a shallow magma reservoir. Thickness and

IMPROVING CO2 EFFICIENCY FOR RECOVERING OIL IN HETEROGENEOUS RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Reid B. Grigg

2003-10-31

The second annual report of ''Improving CO{sub 2} Efficiency for Recovery Oil in Heterogeneous Reservoirs'' presents results of laboratory studies with related analytical models for improved oil recovery. All studies have been undertaken with the intention to optimize utilization and extend the practice of CO{sub 2} flooding to a wider range of reservoirs. Many items presented in this report are applicable to other interest areas: e.g. gas injection and production, greenhouse gas sequestration, chemical flooding, reservoir damage, etc. Major areas of studies include reduction of CO{sub 2} mobility to improve conformance, determining and understanding injectivity changes in particular injectivity loses, and modeling process mechanisms determined in the first two areas. Interfacial tension (IFT) between a high-pressure, high-temperature CO{sub 2} and brine/surfactant and foam stability are used to assess and screen surfactant systems. In this work the effects of salinity, pressure, temperature, surfactant concentration, and the presence of oil on IFT and CO{sub 2} foam stability were determined on the surfactant (CD1045{trademark}). Temperature, pressure, and surfactant concentration effected both IFT and foam stability while oil destabilized the foam, but did not destroy it. Calcium lignosulfonate (CLS) can be used as a sacrificial and an enhancing agent. This work indicates that on Berea sandstone CLS concentration, brine salinity, and temperature are dominant affects on both adsorption and desorption and that adsorption is not totally reversible. Additionally, CLS adsorption was tested on five minerals common to oil reservoirs; it was found that CLS concentration, salinity, temperature, and mineral type had significant effects on adsorption. The adsorption density from most to least was: bentonite > kaolinite > dolomite > calcite > silica. This work demonstrates the extent of dissolution and precipitation from co-injection of CO{sub 2} and

Petrographic characterization to build an accurate rock model using micro-CT: Case study on low-permeable to tight turbidite sandstone from Eocene Shahejie Formation.

Science.gov (United States)

Munawar, Muhammad Jawad; Lin, Chengyan; Cnudde, Veerle; Bultreys, Tom; Dong, Chunmei; Zhang, Xianguo; De Boever, Wesley; Zahid, Muhammad Aleem; Wu, Yuqi

2018-03-26

Pore scale flow simulations heavily depend on petrographic characterizing and modeling of reservoir rocks. Mineral phase segmentation and pore network modeling are crucial stages in micro-CT based rock modeling. The success of the pore network model (PNM) to predict petrophysical properties relies on image segmentation, image resolution and most importantly nature of rock (homogenous, complex or microporous). The pore network modeling has experienced extensive research and development during last decade, however the application of these models to a variety of naturally heterogenous reservoir rock is still a challenge. In this paper, four samples from a low permeable to tight sandstone reservoir were used to characterize their petrographic and petrophysical properties using high-resolution micro-CT imaging. The phase segmentation analysis from micro-CT images shows that 5-6% microporous regions are present in kaolinite rich sandstone (E3 and E4), while 1.7-1.8% are present in illite rich sandstone (E1 and E2). The pore system percolates without micropores in E1 and E2 while it does not percolate without micropores in E3 and E4. In E1 and E2, total MICP porosity is equal to the volume percent of macrospores determined from micro-CT images, which indicate that the macropores are well connected and microspores do not play any role in non-wetting fluid (mercury) displacement process. Whereas in E3 and E4 sandstones, the volume percent of micropores is far less (almost 50%) than the total MICP porosity which means that almost half of the pore space was not detected by the micro-CT scan. PNM behaved well in E1 and E2 where better agreement exists in PNM and MICP measurements. While E3 and E4 exhibit multiscale pore space which cannot be addressed with single scale PNM method, a multiscale approach is needed to characterize such complex rocks. This study provides helpful insights towards the application of existing micro-CT based petrographic characterization methodology

Study on detailed geological modelling for fluvial sandstone reservoir in Daqing oil field

Energy Technology Data Exchange (ETDEWEB)

Zhao Hanqing; Fu Zhiguo; Lu Xiaoguang [Institute of Petroleum Exploration and Development, Daqing (China)

1997-08-01

Guided by the sedimentation theory and knowledge of modern and ancient fluvial deposition and utilizing the abundant information of sedimentary series, microfacies type and petrophysical parameters from well logging curves of close spaced thousands of wells located in a large area. A new method for establishing detailed sedimentation and permeability distribution models for fluvial reservoirs have been developed successfully. This study aimed at the geometry and internal architecture of sandbodies, in accordance to their hierarchical levels of heterogeneity and building up sedimentation and permeability distribution models of fluvial reservoirs, describing the reservoir heterogeneity on the light of the river sedimentary rules. The results and methods obtained in outcrop and modem sedimentation studies have successfully supported the study. Taking advantage of this method, the major producing layers (PI{sub 1-2}), which have been considered as heterogeneous and thick fluvial reservoirs extending widely in lateral are researched in detail. These layers are subdivided into single sedimentary units vertically and the microfacies are identified horizontally. Furthermore, a complex system is recognized according to their hierarchical levels from large to small, meander belt, single channel sandbody, meander scroll, point bar, and lateral accretion bodies of point bar. The achieved results improved the description of areal distribution of point bar sandbodies, provide an accurate and detailed framework model for establishing high resolution predicting model. By using geostatistic technique, it also plays an important role in searching for enriched zone of residual oil distribution.

Characterization of the Lower Cambrian sandstone aquifer in the Swedish Baltic Sea area - assessment regarding its potential suitability for storage of CO2

Science.gov (United States)

Erlström, M.; Sivhed, U.

2012-04-01

In the Baltic region the Cambrian sandstone is considered to have great economic value concerning its aquifer and reservoir properties. Its potential as petroleum reservoir is well known, especially from the Polish, Lithuanian and Russian sectors of the Baltic Sea where oil and gas has been found in anticline traps in the sandstone sequence. Offshore exploration in the Swedish sector has so far not encountered any significant findings of oil and gas. However, the extensive exploration has generated data, which is now being used for assessing the overall properties regarding suitability for storage of CO2. The Swedish primary industry has a great interest in finding potential sites for storage of CO2. A suitable site in the Baltic Sea would be a most favourable alternative in comparison to more remote alternatives such as deep saline aquifers in the North Sea. The Lower Cambrian is in the Swedish sector of the Baltic Sea composed of three main sandstone units varying in thickness between 5 and 50 m occurring within an up to 250 m thick Cambrian sequence dominated by fine-grained terriclastic sediments. The limit of Lower Palaeozoic sequence in the Baltic area is today defined by erosional truncation because of the gently dipping Lower Palaeozoic sequence. To the north and northwest, the limit is found in the Pre-Quaternary, whereas the erosional limit is deeply buried beneath Permian and Mesozoic sediments to the south. Here the Lower Palaeozoic limit is buried to depths reaching more than 2 km. The Cambrian sequence in the distal parts of the Swedish sector occurs at depths of c. 1300 m while it constitutes the bedrock surface in a narrow zone trending from Öland to the north of of Gotland. Sandstone beds constitute 40-60% of the total Cambrian sequence. The main sandstone units have a regional distribution of several thousands of square kilometres. The up to 50 m thick Faludden sandstone member exhibits the best reservoir properties including porosities in the

Study of pressure maintenance in the lower Gassi Touil reservoir

Energy Technology Data Exchange (ETDEWEB)

Ribuot, M.

1969-11-01

The Gassi Touil reservoir in the Sahara is a faulted anticline; the reservoir rock consists of a series of shales and sandstones. It has a primary gas cap in equilibrium with the oil. The oil-gas interface is at 1,642 m; the oil-water interface at 1,970 m. Initial pressure was substantially above hydrostatic. The reservoir contains about 97 million tons STO. A 3-phase, 3-dimensional computer model was used to study the recovery by primary depletion, and by pressure maintenance by gas or water injection. Water injection yields the maximum recovery, but its full efficiency is limited by the fact that only one row of wells can be drilled to the annulus where the wells penetrate only the oil zone. This operation must be supplemented with gas injection into the expanding gas cap in order to efficiently maintain in the reservoir pressure.

Relationship between characteristics of fan-delta sandstone bodies and in-situ leachable sandstone-type uranium mineralization

International Nuclear Information System (INIS)

Nie Fengjun; Zhou Weixun; Guan Taiyang; Li Sitian

2000-01-01

Like normal deltas, fan-deltas are composed of three parts, i.e., fan-delta plain, fan-delta front and pre-fin-delta, In-situ leachable uranium deposits are commonly distributed along the margins of in-land basins. The author analyzes the possible relationship between the basic characteristics of fan-delta sandstone bodies and uranium mineralization. Two examples, e.g., the fan delta depositional systems in the eastern part of Jungger basin and the southern part of Yili basin, are given to illustrate the fan-delta vertical sequence and planar distribution of sedimentary facies. It has been pointed out that the braided channel sandstone bodies on delta plain, sub-aqueous distributional channel sandstone bodies and delta front sandstone bodies may be the favourable host rocks for in-situ leachable sandstone uranium deposits

Predicting interwell heterogeneity in fluvial-deltaic reservoirs: Outcrop observations and applications of progressive facies variation through a depositional cycle

Energy Technology Data Exchange (ETDEWEB)

Knox, P.R.; Barton, M.D. [Univ. of Texas, Austin, TX (United States)

1997-08-01

Nearly 11 billion barrels of mobile oil remain in known domestic fluvial-deltaic reservoirs despite their mature status. A large percentage of this strategic resource is in danger of permanent loss through premature abandonment. Detailed reservoir characterization studies that integrate advanced technologies in geology, geophysics, and engineering are needed to identify remaining resources that can be targeted by near-term recovery methods, resulting in increased production and the postponement of abandonment. The first and most critical step of advanced characterization studies is the identification of reservoir architecture. However, existing subsurface information, primarily well logs, provides insufficient lateral resolution to identify low-permeability boundaries that exist between wells and compartmentalize the reservoir. Methods to predict lateral variability in fluvial-deltaic reservoirs have been developed on the basis of outcrop studies and incorporate identification of depositional setting and position within a depositional cycle. The position of a reservoir within the framework of a depositional cycle is critical. Outcrop studies of the Cretaceous Ferron Sandstone of Utah have demonstrated that the architecture and internal heterogeneity of sandstones deposited within a given depositional setting (for example, delta front) vary greatly depending upon whether they were deposited in the early, progradational part of a cycle or the late, retrogradational part of a cycle. The application of techniques similar to those used by this study in other fluvial-deltaic reservoirs will help to estimate the amount and style of remaining potential in mature reservoirs through a quicklook evaluation, allowing operators to focus characterization efforts on reservoirs that have the greatest potential to yield additional resources.

A comparison between the pressure-lag model and the rate-type model for the prediction of reservoir compaction and surface subsidence

Energy Technology Data Exchange (ETDEWEB)

Smits, R.M.M.; De Waal, J.A.

1988-06-01

A theoretical study has been carried out to investigate whether the nonlinear compaction behavior of sandstone reservoirs, which has been reported for most well-documented field cases, can be explained by pressure lags in interbedding and/or neighboring low-permeability (shale) layers. On the basis of the results obtained, it is concluded that pressure-lag effects in normally encountered production scenarios cannot account for these nonlinearities, even under worst-case conditions. Therefore, the nonlinear field-compaction behavior must be caused by rate effects in the sandstone reservoir rock itself. This is supported by the fact that a rate-type compaction model recently introduced does indeed give a good description of the observed field behavior.

Formation factor in Bentheimer and Fontainebleau sandstones: Theory compared with pore-scale numerical simulations

Science.gov (United States)

Ghanbarian, Behzad; Berg, Carl F.

2017-09-01

Accurate quantification of formation resistivity factor F (also called formation factor) provides useful insight into connectivity and pore space topology in fully saturated porous media. In particular the formation factor has been extensively used to estimate permeability in reservoir rocks. One of the widely applied models to estimate F is Archie's law (F = ϕ- m in which ϕ is total porosity and m is cementation exponent) that is known to be valid in rocks with negligible clay content, such as clean sandstones. In this study we compare formation factors determined by percolation and effective-medium theories as well as Archie's law with numerical simulations of electrical resistivity on digital rock models. These digital models represent Bentheimer and Fontainebleau sandstones and are derived either by reconstruction or directly from micro-tomographic images. Results show that the universal quadratic power law from percolation theory accurately estimates the calculated formation factor values in network models over the entire range of porosity. However, it crosses over to the linear scaling from the effective-medium approximation at the porosity of 0.75 in grid models. We also show that the effect of critical porosity, disregarded in Archie's law, is nontrivial, and the Archie model inaccurately estimates the formation factor in low-porosity homogeneous sandstones.

Application of Advanced Reservoir Characterization, Simulation, and Production Optimization Strategies to Maximize Recovery in Slope and Basin Clastic Reservoirs, West Texas (Delaware Basin)

International Nuclear Information System (INIS)

Dutton, Shirley

1999-01-01

The objective of this Class 3 project was demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost effective way to recover a higher percentage of the original oil in place through strategic placement of infill wells and geologically based field development. Project objectives are divided into two main phases. The original objectives of the reservoir-characterization phase of the project were (1) to provide a detailed understanding of the architecture and heterogeneity of two representative fields of the Delaware Mountain Group, Geraldine Ford and Ford West, which produce from the Bell Canyon and Cherry Canyon Formations, respectively, (2) to chose a demonstration area in one of the fields, and (3) to simulate a CO 2 flood in the demonstration area

Coronation Hill U-Au mine, South Alligator Valley, Northern Territory: an epigenetic sandstone-type deposit hosted by debris-flow conglomerate

International Nuclear Information System (INIS)

Needham, R.S.; Stuart-Smith, P.G.

1987-01-01

The host rock at the Coronation Hill U-Au mine is a debris flow conglomerate, developed in a high-energy fluvial environment during deposition of the Coronation Sandstone of the El Sherana Group. Mineralisation took place by movement of low-temperature fluids from the U-enriched volcanics into the conduit sandstone and eventually into the reduced debris flow conglomerate and carbonaceous shale

Mathematical simulation of oil reservoir properties

International Nuclear Information System (INIS)

Ramirez, A.; Romero, A.; Chavez, F.; Carrillo, F.; Lopez, S.

2008-01-01

The study and computational representation of porous media properties are very important for many industries where problems of fluid flow, percolation phenomena and liquid movement and stagnation are involved, for example, in building constructions, ore processing, chemical industries, mining, corrosion sciences, etc. Nevertheless, these kinds of processes present a noneasy behavior to be predicted and mathematical models must include statistical analysis, fractal and/or stochastic procedures to do it. This work shows the characterization of sandstone berea core samples which can be found as a porous media (PM) in natural oil reservoirs, rock formations, etc. and the development of a mathematical algorithm for simulating the anisotropic characteristics of a PM based on a stochastic distribution of some of their most important properties like porosity, permeability, pressure and saturation. Finally a stochastic process is used again to simulated the topography of an oil reservoir

Endolithic algae of semi-desert sandstones: systematic, biogeographic and ecophysiologic investigations

International Nuclear Information System (INIS)

Bell, R.A.

1986-01-01

Investigations were conducted into the ecology of an unusual algal community in northern Arizona. These microorganisms are called endolithic algae because they occur beneath the surface of rocks. Eighteen taxa, including representatives of both eukaryotic and prokaryotic genera, were isolated from below the surface of eight sandstones in four semi-desert and cold temperate biomes of the Colorado Plateau. As the macroclimate of the area changes from cold temperature desert scrub to cold temperate forest the taxonomic composition of the endolithic algal communities shifts from domination by coccoid blue-green algae to domination by coccoid and sarcinoid green algae. The algal communities varied in generic composition, chlorophyll a content, and in their location within the different sandstones. Investigations into the microclimate of the endolithic algal zone in two adjacent but differently-colored sections (white and brown) of Coconino sandstone have demonstrated differences between the environment above the rock surface and that just beneath the surface. In seasonal samples of the Coconino sandstone, chlorophyll a content ranged from 50 to 100 mg x m -2 in the white rock and 8 to 45 mg x m -2 in the brown rock. Primary production (as measured by 14 CO 2 incorporation) displayed marked seasonal patterns that appear to be correlated to the environmental conditions within the rocks as opposed to those outside the rocks. The widespread distribution of certain algae in the endolithic habitats of the Colorado Plateau and their presence in rocks at quite distant locations suggests that the endolithic habitat may be utilized by algae whenever it provides more favorable conditions than the surrounding surfaces

Uranium deposits: northern Denver Julesburg basin, Colorado

International Nuclear Information System (INIS)

Reade, H.L.

1978-01-01

The Fox Hills Sandstone and the Laramie Formation (Upper Cretaceous) are the host rocks for uranium deposits in Weld County, northern Denver Julesburg basin, Colorado. The uranium deposits discovered in the Grover and Sand Creek areas occur in well-defined north--south trending channel sandstones of the Laramie Formation whereas the sandstone channel in the upper part of the Fox Hills Sandstone trends east--west. Mineralization was localized where the lithology was favorable for uranium accumulation. Exploration was guided by log interpretation methods similar to those proposed by Bruce Rubin for the Powder River basin, Wyoming, because alteration could not be readily identified in drilling samples. The uranium host rocks consist of medium- to fine-grained carbonaceous, feldspathic fluvial channel sandstones. The uranium deposits consist of simple to stacked roll fronts. Reserve estimates for the deposits are: (1) Grover 1,007,000 lbs with an average grade of 0.14 percent eU 3 O 8 ,2) Sand Creek 154,000 lbs with an average grade of 0.08 percent eU 3 O 8 , and 3) The Pawnee deposit 1,060,000 lbs with an average grade of 0.07 percent eU 3 O 8 . The configuration of the geochemical cells in the Grover and Sand Creek sandstones indicate that uraniferous fluids moved northward whereas in the Pawnee sandstone of the Fox Hills uraniferous fluids moved southward. Precipitation of uranium in the frontal zone probably was caused by downdip migration of oxygcnated groundwater high in uranium content moving through a favorable highly carbonaceous and pyritic host sandstone

Epidemiological distribution of rodents as potent reservoirs for infectious diseases in the provinces of Mazandaran, Gilan and Golestan, northern Iran

Directory of Open Access Journals (Sweden)

Behzad Esfandiari

2017-05-01

Full Text Available Rodents are mammals that comprise more than 2000 species and approximately 30 families. There are many morphological and ecological differences among them as variations in their shape, size, weight and habitat. In addition to significant economic losses, rodents have a major role in the dissemination of infectious diseases caused by viruses, bacteria, parasites or other micro-organisms. Rodents are important reservoirs of diseases which have been observed in many cities of Iran provinces especially along Caspian Sea border to Alborz Mountain. The aim of this study is to assess the geographical distribution of rodents in three provinces of northern part of Iran as reservoir of potential endemic infectious diseases. Rodents in 10 major parts of each of the three provinces of Mazandaran, Gilan and Golestan, northern Iran were collected and a total of 404 rodents were trapped alive. They were determined by the key characteristics such as gender, genus, species, different locations and topological situation. Statistical analysis was performed to characterize the study sample and to correlate all variables and parameters. The distribution frequencies of three, five and six genera of rodents were identified in Mazandaran, Gilan and Golestan provinces respectively. The overall distribution frequency of eight genera of rodents in the three provinces were identified as Rattus (R. norvegicus (67.3%, R. rattus (13.6%, Apodemus sylvaticus (13.9%, Arvicola (1%, Mus musculus (0.3%, Nesokia indica (2.5%, Cricetulus migrates (0.7% and Rhombomys opimus (0.7%. The results of this study determined the geographic distribution of the rodents in the three northern provinces of Iran. It is indicated the association of various distribution and diversity of rodents with provincial location. The overall distribution frequency of eight genera of rodents was recognized in the above three provinces geographical locations. This study confirms epidemiological distribution of

Feasibility of a data-constrained prediction of hydrocarbon reservoir sandstone microstructures

International Nuclear Information System (INIS)

Yang, Y S; Gureyev, T E; Tulloh, A; Clennell, M B; Pervukhina, M

2010-01-01

Microstructures are critical for defining material characteristics such as permeability, mechanical, electrical and other physical properties. However, the available techniques for determining compositional microstructures through segmentation of x-ray computed tomography (CT) images are inadequate when there are finer structures than the CT spatial resolution, i.e. when there is more than one material in each voxel. This is the case for CT imaging of geomaterials characterized with submicron porosity and clay coating that control petrophysical properties of rock. This note outlines our data-constrained modelling (DCM) approach for prediction of compositional microstructures, and our investigation of the feasibility of determining sandstone microstructures using multiple CT data sets with different x-ray beam energies. In the DCM approach, each voxel is assumed to contain a mixture of multiple materials, optionally including voids. Our preliminary comparisons using model samples indicate that the DCM-predicted compositional microstructure is consistent with the known original microstructure under low noise conditions. The approach is quite generic and is applicable to predictions of microstructure of various materials. (technical design note)

Delta 37Cl and Characterisation of Petroleum-gas Reservoirs

Science.gov (United States)

Woulé Ebongué, V.; Jendrzejewski, N.; Walgenwitz, F.; Pineau, F.; Javoy, M.

2003-04-01

The geochemical characterisation of formation waters from oil/gas fields is used to detect fluid-flow barriers in reservoirs and to reconstruct the system dynamic. During the progression of the reservoir filling, the aquifer waters are pushed by hydrocarbons toward the reservoir bottom and their compositions evolve due to several parameters such as water-rock interactions, mixing with oil-associated waters, physical processes etc. The chemical and isotopic evolution of these waters is recorded in irreducible waters that have been progressively "fossilised" in the oil/gas column. Residual salts precipitated from these waters were recovered. Chloride being the most important dissolved anion in these waters and not involved in diagenetic reactions, its investigation should give insights into the different transport or mixing processes taking place in the sedimentary basin and point out to the formation waters origins. The first aim of our study was to test the Cl-RSA technique (Chlorine Residual Salts Analysis) based on the well-established Sr-RSA technique. The main studied area is a turbiditic sandstone reservoir located in the Lower Congo basin in Angola. Present-day aquifer waters, irreducible waters from sandstone and shale layers as well as drilling mud and salt dome samples were analysed. Formation waters (aquifer and irreducible trapped in shale) show an overall increase of chlorinity with depth. Their δ37Cl values range from -1.11 ppm to +2.30 ppm ± 0.05 ppm/ SMOC. Most Cl-RSA data as well as the δ37Cl obtained on a set of water samples (from different aquifers in the same area) are lower than -0.13 ppm with lower δ37Cl values at shallower depths. In a δ37Cl versus chlorinity diagram, they are distributed along a large range of chlorinity: 21 to 139 g/l, in two distinct groups. (1) Irreducible waters from one of the wells display a positive correlation between chlorinity and the δ37Cl values. (2) In contrary, the majority of δ37Cl measured on aquifers

Conversion of Crude Oil to Methane by a Microbial Consortium Enriched From Oil Reservoir Production Waters

Directory of Open Access Journals (Sweden)

Carolina eBerdugo-Clavijo

2014-05-01

Full Text Available The methanogenic biodegradation of crude oil is an important process occurring in petroleum reservoirs and other oil-containing environments such as contaminated aquifers. In this process, syntrophic bacteria degrade hydrocarbon substrates to products such as acetate, and/or H2 and CO2 that are then used by methanogens to produce methane in a thermodynamically dependent manner. We enriched a methanogenic crude oil-degrading consortium from production waters sampled from a low temperature heavy oil reservoir. Alkylsuccinates indicative of fumarate addition to C5 and C6 n-alkanes were identified in the culture (above levels found in controls, corresponding to the detection of an alkyl succinate synthase gene (assA in the culture. In addition, the enrichment culture was tested for its ability to produce methane from residual oil in a sandstone-packed column system simulating a mature field. Methane production rates of up 5.8 μmol CH4/g of oil/day were measured in the column system. Amounts of produced methane were in relatively good agreement with hydrocarbon loss showing depletion of more than 50% of saturate and aromatic hydrocarbons. Microbial community analysis revealed that the enrichment culture was dominated by members of the genus Smithella, Methanosaeta, and Methanoculleus. However, a shift in microbial community occurred following incubation of the enrichment in the sandstone columns. Here, Methanobacterium sp. were most abundant, as were bacterial members of the genus Pseudomonas and other known biofilm forming organisms. Our findings show that microorganisms enriched from petroleum reservoir waters can bioconvert crude oil components to methane both planktonically and in sandstone-packed columns as test systems. Further, the results suggest that different organisms may contribute to oil biodegradation within different phases (e.g., planktonic versus sessile within a subsurface crude oil reservoir.

Evolution of pores and fractures in an unconventional Upper Carboniferous reservoir analogue, Westphalian D, W-Germany

Energy Technology Data Exchange (ETDEWEB)

Hoehne, M.; Schurk, K.; Hilgers, C. [RWTH Aachen Univ. (Germany). Reservoir-Petrology, Energy and Mineral Resources Group (EMR); Koehrer, B. [Wintershall Holding GmbH, Barnstorf (Germany); Bertier, P. [RWTH Aachen Univ. (Germany). Inst. of Clay and Interface Mineralogy

2013-08-01

Uncertainties in reservoir characterization of tight gas sandstones can be significantly reduced by using quantitative data from outcrops. The active Piesberg quarry near Osnabrueck exposes Upper Carboniferous strata and therefore provides a reservoir outcrop analog to the gas-bearing tight gas fields in NW-Germany. This study focused on variations of sedimentary facies, porosity, diagenesis and structural inventory in the quarry. The Westphalian D strata at Piesberg consist of siliciclastic, coarse- to fine-grained sandstones with a strong cementation, intercalated with coal seams, siltstones and mudstones. Petrography shows shale-, mudstone and clay rip-up fragments squeezed into primary porosity during eodiagenesis. Sandstone types commonly show low porosities (<10 %) and very low permeabilities (<0.01 mD) mainly due to intense quartz cementation. Scarce authigenic carbonates are euhedral ankerites formed during burial. Secondary porosity resulted mostly from detrital carbonate leaching and limited dissolution of feldspars. Within a zone of up to several meters around faults, porosity is much higher. Feldspars are almost completely altered to illite and locally to kaolinite. Partly dissolved detrital carbonates show Fe-oxide margins around intragranular pores, indicative of Fe-rich compositions formed during telo-diagenesis. Both joints and faults were mapped throughout the quarry and strike, slip and throw of the latter were documented. Cemented fractures prevail around faults and may thus be associated with the structural and diagenetic evolution of the Upper Carboniferous of the Piesberg area. This study is embedded into a larger outcrop analog study of RWTH Aachen in cooperation with Wintershall. Its aim is to unravel the impact of structural diagenesis on the alteration and evolution of pore space and thus reservoir quality. Results can be used to develop datadriven exploration strategies and improved development options for analogous subsurface tight gas

Chemical, physical characterization and salinity distribution of the oilfield water in the Upper Sandstone Member of the Zubair reservoir at Rumaila North Oilfield, Southern Iraq

Directory of Open Access Journals (Sweden)

Salih Awadh

2018-01-01

Full Text Available The oilfield water in the Upper Sandstone Member of the Zubair reservoir (Barriemian-Hauterivian at Rumaila North Oil Field was investigated for the interpretation of salinity and geochemical evolution of brine compositions. The interaction of the oilfield water with reservoir rock resulted in a brine water derived from the marine water origin of partial mixing with meteoric water similar to the compositional ranges of formation water from Gulf of Mexico offshore/onshore Mesozoic reservoirs. The high TDS (207350- 230100; average 215625 mg/L is consistent with the electrical conductivity (340362-372762; average 351024μs, and predominantly represented by Cl (123679 mg/L as anions and (29200 and 14674 mg/L for Na and Ca as cations respectively. The contribution of cation (epm% are as Na (70.2, Ca (18.9, Mg (8.1 and K (1.7; and anion as Cl (99.7, SO4 (0.25, HCO3 (0.07 and CO3 (0.005. sodium (57550-60500mg/L is greater than of seawater six times, calcium and magnesium three times greater, and chloride 6.5 times greater, but Sulfate is depleted to six times less due to a sulfur release from sulphates and link with different hydrocarbon species, precipices as native sulphur and link with hydrogen forming H2S. The Zubair oilfield water is characterised by acidic pH (pH=5.2- 5.77 enhanced petrophysical properties, high specific gravity (1.228 predicts a high fluid pressure (4866 psi, hydrocarbon saturation (0.43%, water saturation (0.57% and porosity (12.7. The Mineral saturation model indicates that the Zubair oilfield water is an unsaturated water with respect to all suggested minerals at 5.45, but at simulated pH, brucite being an equilibrium at pH 9.12, but brucite and portlandite being supersaturated at pH 11.9. The mineral solubility responses to the changes in temperature, pressure, pH, Eh, and ionic strength, thereby formation damage is proportionally developed.

A Rock Physics Feasibility Study of the Geothermal Gassum Reservoir, Copenhagen Area, Denmark

DEFF Research Database (Denmark)

Bredesen, Kenneth; Dalgaard, Esben Borch; Mathiesen, Anders

The subsurface of Denmark stores significant amounts of renewable geothermal energy which may contribute to domestic heating for centuries. However, establishing a successful geothermal plant with robust production capacity require reservoirs with sufficient high porosity and permeability. Modern...... quantitative seismic interpretation is a good approach to de-risk prospects and gain reservoir insight, but is so far not widely used for geothermal applications. In this study we perform a rock physics feasibility study as a pre-step towards quantitative seismic interpretation of geothermal reservoirs......, primarily in areas around Copenhagen. The results argue that it may be possible to use AVO and seismic inversion data to distinguish geothermal sandstone reservoirs from surrounding shales and to estimate porosity and permeability. Moreover, this study may represent new possibilities for future rock physics...

Features of Composition and Cement Type of the Lower Triassic Reservoirs in the North of the Timan-Pechora Oil and Gas Province

Directory of Open Access Journals (Sweden)

N.N. Timonina

2017-03-01

Full Text Available The work is devoted to the study of cement type and composition of the Lower Triassic deposits of the Timan-Pechora province, their influence on reservoir properties of rocks. The work was based on laboratory studies of core, generalization of published data. Morphological and genetic analysis of clay minerals was carried out using X-ray and electron-microscopic methods. As a result of the conducted studies it was established that the type, composition and distribution of the cement is influenced by the composition of demolition sources, sedimentation conditions, and post-sedimentation transformations. Kaolinite, chlorite, smectite and hydromica associations are distinguished according to the predominance of clay mineral in the sandstone cement. Kaolinite cement of sandstones is most typical for continental fluvial facies, especially channel beds. Smectite association is most characteristic of the floodplain, oxbow and lake facies of the zone. The revealed regularities will contribute to the improvement of accurate reconstruction of sedimentation conditions, construction of more adequate geological models of the reservoir, taking into account its reservoir heterogeneity both at the level of the reservoir and its constituent interlayers.

Oligo-Miocene reservoir sequence characterization and structuring in the Sisseb El Alem-Kalaa Kebira regions (Northeastern Tunisia)

Science.gov (United States)

Houatmia, Faten; Khomsi, Sami; Bédir, Mourad

2015-11-01

The Sisseb El Alem-Enfidha basin is located in the northeastern Tunisia, It is borded by Nadhour - Saouaf syncline to the north, Kairouan plain to the south, the Mediterranean Sea to the east and Tunisian Atlassic "dorsale" to the west. Oligocene and Miocene deltaic deposits present the main potential deep aquifers in this basin with high porosity (25%-30%). The interpretation of twenty seismic reflection profiles, calibrated by wire line logging data of twelve oil wells, hydraulic wells and geologic field sections highlighted the impact of tectonics on the structuring geometry of Oligo-Miocene sandstones reservoirs and their distribution in raised structures and subsurface depressions. Miocene seismostratigraphy analysis from Ain Ghrab Formation (Langhian) to the Segui Formation (Quaternary) showed five third-order seismic sequence deposits and nine extended lenticular sandy bodies reservoirs limited by toplap and downlap surfaces unconformities, Oligocene deposits presented also five third- order seismic sequences with five extended lenticular sandy bodies reservoirs. The Depth and the thickness maps of these sequence reservoir packages exhibited the structuring of this basin in sub-basins characterized by important lateral and vertical geometric and thichness variations. Petroleum wells wire line logging correlation with clay volume calculation showed an heterogeneous multilayer reservoirs of Oligocene and Miocene formed by the arrangement of fourteen sandstone bodies being able to be good reservoirs, separated by impermeable clay packages and affected by faults. Reservoirs levels correspond mainly to the lower system tract (LST) of sequences. Intensive fracturing by deep seated faults bounding the different sub-basins play a great role for water surface recharge and inter-layer circulations between affected reservoirs. The total pore volume of the Oligo-Miocene reservoir sandy bodies in the study area, is estimated to about 4 × 1012 m3 and equivalent to 4 �

Sedimentological Characterization of a Deepwater Methane Hydrate Reservoir in Green Canyon 955, Northern Gulf of Mexico

Science.gov (United States)

Meazell, K.; Flemings, P. B.

2017-12-01

Grain size is a controlling factor of hydrate saturation within a Pleistocene channel-levee system investigated by the UT-GOM2-1 expedition within the deepwater northern Gulf of Mexico. Laser diffraction and settling experiments conducted on sediments from 413-440 meters below the seafloor reveal the presence of two interbedded lithologic units, identified as a silty sand and a clayey silt, according Shepard's classification system. The sand-rich lithofacies has low density and high p-wave velocity, suggesting a high degree of hydrate saturation. Conversely, the clay and silt dominated lithofacies is characterized by a higher density and low p-wave velocity, suggesting low hydrate saturation. The sand-rich lithofacies is well-sorted and displays abundant ripple lamination, indicative of deposition within a high-energy environment. The clayey-silt is poorly-sorted and lacks sedimentary structures. The two lithofacies are interbedded throughout the reservoir unit; however, the relative abundance of the sand-rich lithofacies increases with depth, suggesting a potential decrease in flow energy or sediment flux over time, resulting in the most favorable reservoir properties near the base of the unit.

Cathodoluminescence characteristics of sandstone and the implications for sandstone type No. 512 uranium deposit

International Nuclear Information System (INIS)

Liu Xiaodong; Guan Taiyang

1998-12-01

Cathodoluminescence (CL) technique, as a special petrologic tool, has been applied to the studies of uranium hosted sandstone from No. 512 uranium deposit located in Xinjiang Autonomous Region, Northwest China. The detrital grains including quartz, feldspar, debris and cements display distinguishing CL properties. The quartz grains mainly demonstrate brown and dark blue CL, feldspar grains demonstrate blue and bright blue CL, calcite cement displays bright yellow-orange and orange-red CL with significant CL zoning, while the debris, mud and sand cements have dark red CL, multicolor CL or non-luminescence. The characteristics of overgrowth, fracture healing, and the original contact relations of detrital grains appear much more significant with CL than that with conventional visual methods. Much more information can be contributed by CL technique to decipher the provenance area, to explain the cementation, consolidation and other diagenesis processes of sandstone. The CL technique also provides and efficient tool for identifying detrital grains and cements, and for more precisely estimating the proportions of various detrital grains and cement components in sandstone. The CL emission of uranium hosted sandstone revealed the existence of radiation-damage rims of quartz grains at the places with a little or no uranium minerals nearby, which may imply a uranium-leaching episode during the diagenesis of sandstone

Biogenic origin of coalbed gas in the northern Gulf of Mexico Coastal Plain, U.S.A

Science.gov (United States)

Warwick, Peter D.; Breland, F. Clayton; Hackley, Paul C.

2008-01-01

New coal-gas exploration and production in northern Louisiana and south-central Mississippi, Gulf of Mexico Basin, is focused on the Wilcox Group (Paleocene–Eocene), where the depth to targeted subbituminous C to high volatile C bituminous coal beds ranges from 300 to 1680 m, and individual coal beds have a maximum thickness of about 6 m. Total gas content (generally excluding residual gas) of the coal beds ranges from less than 0.37 cm3/g (as-analyzed or raw basis; 1.2 cm3/g, dry, ash free basis, daf) at depths less than 400 m, to greater than 7.3 cm3/g (as-analyzed basis; 8.76 cm3/g, daf) in deeper (> 1,500 m) parts of the basin. About 20 Wilcox coal-gas wells in northern Louisiana produce from 200 to 6485 m3 of gas/day and cumulative gas production from these wells is approximately 25 million m3 (as of December, 2006). U.S. Geological Survey assessment of undiscovered, technically recoverable gas resources in the Gulf of Mexico Coastal Plain, including northern and south-central Mississippi, indicates that coal beds of the Wilcox Group contain an estimated mean total 109.3 million m3 (3.86 trillion ft3) of producible natural gas.To determine the origin of the Wilcox Group coal gases in northern Louisiana, samples of gas, water, and oil were collected from Wilcox coal and sandstone reservoirs and from under- and overlying Late Cretaceous and Eocene carbonate and sandstone reservoirs. Isotopic data from Wilcox coal-gas samples have an average δ13CCH4 value of − 62.6‰ VPDB (relative to Vienna Peedee Belemnite) and an average δDCH4 value of − 199.9‰ VSMOW (relative to Vienna Standard Mean Ocean Water). Values of δ13CCO2 range from − 25.4 to 3.42‰ VPDB. Produced Wilcox saline water collected from oil, conventional gas, and coalbed gas wells have δDH2O values that range from − 27.3 to − 18.0‰ VSMOW. These data suggest that the coal gases primarily are generated in saline formation water by bacterial reduction of CO2

Biogenic origin of coalbed gas in the northern Gulf of Mexico Coastal Plain, U.S.A.

Energy Technology Data Exchange (ETDEWEB)

Warwick, Peter D.; Hackley, Paul C. [U.S. Geological Survey, 956 National Center, Reston, VA 20192 (United States); Breland, F. Clayton Jr. [Louisiana Department of Natural Resources, 617 North 3rd Street, Baton Rouge, LA 70802 (United States)

2008-10-02

New coal-gas exploration and production in northern Louisiana and south-central Mississippi, Gulf of Mexico Basin, is focused on the Wilcox Group (Paleocene-Eocene), where the depth to targeted subbituminous C to high volatile C bituminous coal beds ranges from 300 to 1680 m, and individual coal beds have a maximum thickness of about 6 m. Total gas content (generally excluding residual gas) of the coal beds ranges from less than 0.37 cm{sup 3}/g (as-analyzed or raw basis; 1.2 cm{sup 3}/g, dry, ash free basis, daf) at depths less than 400 m, to greater than 7.3 cm{sup 3}/g (as-analyzed basis; 8.76 cm{sup 3}/g, daf) in deeper (> 1,500 m) parts of the basin. About 20 Wilcox coal-gas wells in northern Louisiana produce from 200 to 6485 m{sup 3} of gas/day and cumulative gas production from these wells is approximately 25 million m{sup 3} (as of December, 2006). U.S. Geological Survey assessment of undiscovered, technically recoverable gas resources in the Gulf of Mexico Coastal Plain, including northern and south-central Mississippi, indicates that coal beds of the Wilcox Group contain an estimated mean total 109.3 million m{sup 3} (3.86 trillion ft{sup 3}) of producible natural gas. To determine the origin of the Wilcox Group coal gases in northern Louisiana, samples of gas, water, and oil were collected from Wilcox coal and sandstone reservoirs and from under- and overlying Late Cretaceous and Eocene carbonate and sandstone reservoirs. Isotopic data from Wilcox coal-gas samples have an average {delta}{sup 13}C{sub CH4} value of - 62.6 permille VPDB (relative to Vienna Peedee Belemnite) and an average {delta}D{sub CH4} value of - 199.9 permille VSMOW (relative to Vienna Standard Mean Ocean Water). Values of {delta}{sup 13}C{sub CO2} range from - 25.4 to 3.42 permille VPDB. Produced Wilcox saline water collected from oil, conventional gas, and coalbed gas wells have {delta}D{sub H2O} values that range from - 27.3 to - 18.0 permille VSMOW. These data suggest that the

An Evaluation of the Carbon Sequestration Potential of the Cambro-Ordovician Strata of the Illinois and Michigan Basins. Part 1. Evaluation of Phase 2 CO₂ Injection Testing in the Deep Saline Gunter Sandstone Reservoir (Cambro-Ordovician Knox Group), Marvin Blan No. 1 Hancock County, Kentucky Part 2. Time-lapse Three-Dimensional Vertical Seismic Profile (3D-VSP) of Sequestration Target Interval with Injected Fluids

Energy Technology Data Exchange (ETDEWEB)

Bowersox, Richard [Univ. of Illinois, Champaign, IL (United States); Hickman, John [Univ. of Illinois, Champaign, IL (United States); Leetaru, Hannes [Univ. of Illinois, Champaign, IL (United States)

2012-12-20

Part 1 of this report focuses on results of the western Kentucky carbon storage test, and provides a basis for evaluating injection and storage of supercritical CO₂ in Cambro-Ordovician carbonate reservoirs throughout the U.S. Midcontinent. This test demonstrated that the Cambro- Ordovician Knox Group, including the Beekmantown Dolomite, Gunter Sandstone, and Copper Ridge Dolomite in stratigraphic succession from shallowest to deepest, had reservoir properties suitable for supercritical CO₂ storage in a deep saline reservoir hosted in carbonate rocks, and that strata with properties sufficient for long-term confinement of supercritical CO₂ were present in the deep subsurface. Injection testing with brine and CO₂ was completed in two phases. The first phase, a joint project by the Kentucky Geological Survey and the Western Kentucky Carbon Storage Foundation, drilled the Marvin Blan No. 1 carbon storage research well and tested the entire Knox Group section in the open borehole – including the Beekmantown Dolomite, Gunter Sandstone, and Copper Ridge Dolomite – at 1152–2255 m, below casing cemented at 1116 m. During Phase 1 injection testing, most of the 297 tonnes of supercritical CO₂ was displaced into porous and permeable sections of the lowermost Beekmantown below 1463 m and Gunter. The wellbore was then temporarily abandoned with a retrievable bridge plug in casing at 1105 m and two downhole pressure-temperature monitoring gauges below the bridge plug pending subsequent testing. Pressure and temperature data were recorded every minute for slightly more than a year, providing a unique record of subsurface reservoir conditions in the Knox. In contrast, Phase 2 testing, this study, tested a mechanically-isolated dolomitic-sandstone interval in the Gunter.

Production Characteristics and Reservoir Quality at the Ivanić Oil Field (Croatia) Predicted by Machine Learning System

OpenAIRE

Hernitz, Zvonimir; Đureković, Miro; Crnički, Josip

1996-01-01

At the Ivanić oil field, hydrocarbons are accumulated in fine tomedium grained litharenits of the Ivanić-Grad Formation (Iva-sandstones member) of Upper Miocene age. Reservoir rocks are dividedinlo eight depositional (production) units (i1- i8). Deposits of eachunit are characterized by their own reservoir quality parameters(porosity, horizontal permeability, net pay ... ). Production characteristicsof 30 wells have been studied by a simple slatistical method. Twomajor production well ca...

"Sydney sandstone": Heritage Stone from Australia

Science.gov (United States)

Cooper, Barry; Kramar, Sabina

2014-05-01

Sydney is Australia's oldest city being founded in 1788. The city was fortunate to be established on an extensive and a relatively undeformed layer of lithified quartz sandstone of Triassic age that has proved to be an ideal building stone. The stone has been long identified by geologists as the Hawkesbury Sandstone. On the other hand the term "Sydney sandstone" has also been widely used over a long period, even to the extent of being utilised as the title of published books, so its formal designation as a heritage stone will immediately formalise this term. The oldest international usage is believed to be its use in the construction of the Stone Store at Kerikeri, New Zealand (1832-1836). In the late 19th century, public buildings such as hospitals, court houses as well as the prominent Sydney Town Hall, Sydney General Post Office, Art Gallery of New South Wales, State Library of New South Wales as well as numerous schools, churches, office building buildings, University, hotels, houses, retaining walls were all constructed using Sydney sandstone. Innumerable sculptures utilising the gold-coloured stone also embellished the city ranging from decorative friezes and capitals on building to significant monuments. Also in the late 19th and early 20th century, Sydney sandstone was used for major construction in most other major Australian cities especially Melbourne, Adelaide and Brisbane to the extent that complaints were expressed that suitable local stone materials were being neglected. Quarrying of Sydney sandstone continues today. In 2000 it was recorded noted that there were 33 significant operating Sydney sandstone quarries including aggregate and dimension stone operations. In addition sandstone continues to be sourced today from construction sites across the city area. Today major dimension stone producers (eg Gosford Quarries) sell Sydney sandstone not only into the Sydney market but also on national and international markets as cladding and paving products

Contribution of suspended particulate matter and zooplankton to MeHg contamination of the food chain in mid-northern Quebec (Canada) reservoirs

International Nuclear Information System (INIS)

Plourde, Y.; Lucotte, M.; Pichet, P.

1997-01-01

The high increase in mercury (Hg) concentrations in fish following the creation of hydroelectric reservoirs was discussed. Flooded forest soils are a major source of mercury contamination of fish after impoundment. Flooding stimulates bacterial activity in the humic horizon of soils and results in the transformation of inorganic mercury into methyl mercury (MeHg), the most toxic form of mercury. The reservoirs of the La Grande hydroelectric complex at James Bay in northern Quebec were sampled and compared to neighbouring natural lakes. Sampling was carried out in 1992 during June, August and September. Results of the analysis revealed an increase in the MeHg concentrations in zooplankton and suspended particulate matter (SPM); mean concentrations were about 5 times higher in the reservoirs than in neighbouring lakes. Although the process is not well understood, it is believed that the MeHg is transferred up the food chain which accounts, in part, for MeHg contamination of fishes. 45 refs., 9 figs

Geomechanical Framework for Secure CO₂ Storage in Fractured Reservoirs and Caprocks for Sedimentary Basins in theMidwest United States

Energy Technology Data Exchange (ETDEWEB)

Sminchak, Joel [Battelle, Columbus, OH (United States)

2017-09-29

This report presents final technical results for the project Geomechanical Framework for Secure CO₂ Storage in Fractured Reservoirs and Caprocks for Sedimentary Basins in the Midwest United States (DE-FE0023330). The project was a three-year effort consisting of seven technical tasks focused on defining geomechanical factors for CO₂ storage applications in deep saline rock formations in Ohio and the Midwest United States, because geomechancial issues have been identified as a significant risk factor for large-scale CO₂ storage applications. A basin-scale stress-strain analysis was completed to describe the geomechanical setting for rock formations of Ordovician-Cambrian age in Ohio and adjacent areas of the Midwest United States in relation to geologic CO₂ storage applications. The tectonic setting, stress orientation-magnitude, and geomechanical and petrophysical parameters for CO₂ storage zones and caprocks in the region were cataloged. Ten geophysical image logs were analyzed for natural fractures, borehole breakouts, and drilling-induced fractures. The logs indicated mostly less than 10 fractures per 100 vertical feet in the borehole, with mostly N65E principal stress orientation through the section. Geophysical image logs and other logs were obtained for three wells located near the sites where specific models were developed for geomechanical simulations: Arches site in Boone County, Kentucky; Northern Appalachian Basin site in Chautauqua County, New York; and E-Central Appalachian Basin site in Tuscarawas County, Ohio. For these three wells, 9,700 feet of image logs were processed and interpreted to provide a systematic review of the distribution within each well of natural fractures, wellbore breakouts, faults, and drilling induced fractures. There were many borehole breakouts and drilling-induced tensile fractures but few natural fractures. Concentrated fractures were present at the Rome-basal sandstone

CO{sub 2}-induced mechanical behaviour of Hawkesbury sandstone in the Gosford basin: An experimental study

Energy Technology Data Exchange (ETDEWEB)

Rathnaweera, T.D. [Department of Civil Engineering, Monash University, Building 60, Melbourne, Victoria 3800 (Australia); Ranjith, P.G., E-mail: ranjith.pg@monash.edu [Department of Civil Engineering, Monash University, Building 60, Melbourne, Victoria 3800 (Australia); Perera, M.S.A.; Haque, A. [Department of Civil Engineering, Monash University, Building 60, Melbourne, Victoria 3800 (Australia); Lashin, A. [King Saud University, College of Engineering-Petroleum and Natural Gas Engineering Department, P.O. Box 800, Riyadh 11421, Saudi Arabia. (Saudi Arabia); Benha University, Faculty of Science-Geology Department, P.O. Box 13518, Benha (Egypt); Al Arifi, N. [King Saud University, College of Science-Geology and Geophysics Department, P.O. Box 2455, Riyadh 11451, Saudi Arabia. (Saudi Arabia); Chandrasekharam, D [King Saud University, College of Science-Geology and Geophysics Department, P.O. Box 2455, Riyadh 11451, Saudi Arabia. (Saudi Arabia); Department of Earth Sciences, Indian Institute of Technology Bombay, 400076 India (India); Yang, SQ [Department of Civil Engineering, Monash University, Building 60, Melbourne, Victoria 3800 (Australia); State Key Laboratory for Geomechanics and Deep Underground Engineering, China University of Mining and Technology, Xuzhou 221116 (China); Xu, T; Wang, SH [Center for Rock Instability & Seismicity Research, Northeastern University, Shenyang 110819 (China); Yasar, E [Iskenderun Technical University, Faculty of Mechanical Engineering, Dept. of Petroleum & Natural Gas Engineering, 31200 (Turkey)

2015-08-12

Carbon dioxide (CO{sub 2}) sequestered in saline aquifers undergoes a variety of chemically-coupled mechanical effects, which may cause CO{sub 2}-induced mechanical changes and time-dependent reservoir deformation. This paper investigates the mineralogical and microstructural changes that occur in reservoir rocks following injection of CO{sub 2} in deep saline aquifers and the manner in which these changes influence the mechanical properties of the reservoir rocks. In this study, cylindrical sandstone specimens, 38 mm in diameter and 76 mm high, obtained from the Gosford basin, were used to perform a series of unconfined compressive strength (UCS) tests. Different saturation conditions: dry, water- and brine-saturated sandstone samples with and without scCO{sub 2} (super-critical carbon dioxide) injection, were considered in the study to obtain a comprehensive understanding of the impact of scCO{sub 2} injection during the CO{sub 2} sequestration process on saline aquifer mechanical properties. An acoustic emission (AE) system was employed to identify the stress threshold values of crack closure, crack initiation and crack damage for each testing condition during the whole deformation process of the specimens. Finally, scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray fluorescence (XRF) analyses were performed to evaluate the chemical and mineralogical changes that occur in reservoir rocks during CO{sub 2} injection. From the test results, it is clear that the CO{sub 2}-saturated samples possessed a lower peak strength compared to non-CO{sub 2} saturated samples. According to SEM, XRD and XRF analyses, considerable quartz mineral corrosion and dissolution of calcite and siderite were observed during the interactions of the CO{sub 2}/water/rock and CO{sub 2}/brine/rock systems, which implies that mineralogical and geochemical rock alterations affect rock mechanical properties by accelerating the collapse mechanisms of the pore matrix. AE results

Effects of reduction in porosity and permeability with depth on storage capacity and injectivity in deep saline aquifers: A case study from the Mount Simon Sandstone aquifer

Science.gov (United States)

Medina, C.R.; Rupp, J.A.; Barnes, D.A.

2011-01-01

The Upper Cambrian Mount Simon Sandstone is recognized as a deep saline reservoir that has significant potential for geological sequestration in the Midwestern region of the United States. Porosity and permeability values collected from core analyses in rocks from this formation and its lateral equivalents in Indiana, Kentucky, Michigan, and Ohio indicate a predictable relationship with depth owing to a reduction in the pore structure due to the effects of compaction and/or cementation, primarily as quartz overgrowths. The regional trend of decreasing porosity with depth is described by the equation: ??(d)=16.36??e-0.00039*d, where ?? is the porosity and d is the depth in m. The decrease of porosity with depth generally holds true on a basinwide scale. Bearing in mind local variations in lithologic and petrophysical character within the Mount Simon Sandstone, the source data that were used to predict porosity were utilized to estimate the pore volume available within the reservoir that could potentially serve as storage space for injected CO2. The potential storage capacity estimated for the Mount Simon Sandstone in the study area, using efficiency factors of 1%, 5%, 10%, and 15%, is 23,680, 118,418, 236,832, and 355,242 million metric tons of CO2, respectively. ?? 2010 Elsevier Ltd.

Clay squirt: Local flow dispersion in shale-bearing sandstones

DEFF Research Database (Denmark)

Sørensen, Morten Kanne; Fabricius, Ida Lykke

2017-01-01

Dispersion of elastic-wave velocity is common in sandstone and larger in shaly sandstone than in clean sandstone. Dispersion in fluid-saturated shaly sandstone often exceeds the level expected from the stress-dependent elastic moduli of dry sandstone. The large dispersion has been coined clay...... squirt and is proposed to originate from a pressure gradient between the clay microporosity and the effective porosity. We have formulated a simple model that quantifies the clay-squirt effect on bulk moduli of sandstone with homogeneously distributed shale laminae or dispersed shale. The model...... predictions were compared with the literature data. For sandstones with dispersed shale, agreement was found, whereas other sandstones have larger fluid-saturated bulk modulus, possibly due to partially load-bearing shales or heterogeneous shale distribution. The data that agree with the clay-squirt model...

Wettability of Oil-Producing Reservoir Rocks as Determined from X-ray Photoelectron Spectroscopy

Science.gov (United States)

Toledo; Araujo; Leon

1996-11-10

Wettability has a dominant effect in oil recovery by waterflooding and in many other processes of industrial and environmental interest. Recently, the suggestion has been made that surface science analytical techniques (SSAT) could be used to rapidly determine the wettability of reservoir materials. Here, we bring the capability of X-ray photoelectron spectroscopy (XPS) to bear on the wettability evaluation of producing reservoir rocks. For a suite of freshly exposed fracture surfaces of rocks we investigate the relationship between wettability and surface composition as determined from XPS. The classical wettability index as measured with the Amott-Harvey test is used here as an indicator of the wettability of natural sandstones. The XPS spectra of oil-wet surfaces of rocks reveal the existence of organic carbon and also of an "organic" silicon species, of the kind Si-CH relevant to silanes, having a well-defined binding energy which differs from that of the Si-O species of mineral grains. We provide quantifiable evidence that chemisorbed organic material on the pore surfaces defines the oil-wetting character of various reservoir sandstones studied here which on a mineralogic basis are expected to be water-wet. This view is supported by a strong correlation between C content of pore surfaces and rock wettability. The results also suggest a correlation between organic silicon content on the pore surfaces and rock hydrophobicity.

Experimental strain analysis of Clarens Sandstone colonised by endolithic lichens

Directory of Open Access Journals (Sweden)

D. Wessels

1995-08-01

Full Text Available Endolithic lichens occur commonly on Clarens Sandstone in South Africa, where they significantly contribute to the weathering of sandstone by means of mechanical and chemical weathering processes. This preliminary investigation reports on the success- ful use of strain gauges in detecting strain differences between sandstone without epilithic lichens and sandstone colonised by the euendolithic lichen Lecidea aff. sarcogynoides Korb. Mechanical weathering, expressed as strain changes, in Clarens Sandstone was studied during the transition from relatively dry winter to wet summer conditions. Daily weathering of sandstone due to thermal expansion and contraction of colonised and uncolonised sandstone could be shown. Our results show that liquid water in sandstone enhances the mechanical weathering of uncolonised Clarens Sandstone while water in the gaseous phase enhances mechanical weathering of sandstone by euendolithic lichens.

Lower Cretaceous Luscar group (revised) of the northern and north-central foothills of Alberta

Energy Technology Data Exchange (ETDEWEB)

Langenberg, C W; McMechan, M E

1985-03-01

Lower Cretaceous coal-bearing strata exposed in the northern and north-central foothills of Alberta form part of a predominantly nonmarine succession that extends from Montana to northeastern British Columbia. The Luscar Group (revised) forms the sequence of coal bearing Lower Cretaceous strata that disconformably overlies marine and nonmarine strata of the Nikanassin Formation or Minnes Group and disconformably underlies marine shales of the Blackstone or Shaftesbury formations. It includes a thin, basal conglomerate, a predominantly nonmarine sandstone and shale unit that locally contains coal; a marine shale and sandstone unit, and an upper nonmarine sandstone and shale unit that contains thick commercial coal seams. These units form the Cadomin, Gladstone, Moosebar and Gates formations, respectively. The Luscar Group is exposed from Kakwa River to Clearwater River in the Foothills of Alberta. It represents a slight modification, by the inclusion of the thin basal conglomerate, from the previous usage of the term Luscar in the northern Foothills of Alberta. 25 references.

Potential petrophysical and chemical property alterations in a compressed air energy storage porous rock reservoir

Energy Technology Data Exchange (ETDEWEB)

Stottlemyre, J.A.; Erikson, R.L.; Smith, R.P.

1979-10-01

Successful commercialization of Compressed Air Energy Storage (CAES) systems depends on long-term stability of the underground reservoirs subjected to somewhat unique operating conditions. Specifically, these conditions include elevated and time varying temperatures, effective stresses, and air humidities. To minimize the requirements for premium fuels, it may be desirable to retain the thermal energy of compression. Porous media, e.g., sandstone, may hold promise as elevated temperature reservoirs. In this study, a reservoir composed of clean quartz sandstone and injection air temperatures of 300 to 575/sup 0/K are assumed. Numerical modeling is used to estimate temperature, stress, and humidity conditions within this reference porous media reservoir. A discussion on relative importance to CAES of several potential porous media damage mechanisms is presented. In this context, damage is defined as a reduction in intrinsic permeability (measure of air transport capability), a decrease in effective porosity (measure of storage capability), or an increase in elastic and/or inelastic deformation of the porous material. The potential damage mechanisms presented include: (1) disaggregation, (2) particulate plugging, (3) boundary layer viscosity anomalies, (4) inelastic microstructural consolidation, (5) clay swelling and dispersion, (6) hydrothermal mineral alteration, (7) oxidation reactions, and (8) well casing corrosion. These mechanisms are placed in perspective with respect to anticipated CAES conditions and mechanisms suggested are: (1) of academic interest only, (2) readily identified and controlled via engineering, or (3) potential problem areas requiring additional investigation.

Distribution, Abundance, and Population Dynamics of Northern Squawfish, Walleye, Smallmouth Bass, and Channel Catfish in John Day Reservoir, 1986 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Beamesderfer, Raymond C.

1987-04-01

John Day Reservoir was sampled from 25 March to 1 September 1986 using gill nets, trap nets, boat electrofishers, hook and line, and an angler survey to collect 4945 northern squawfish Ptychocheilus oregonesis, 602 walleye Stizostedion vitreum 2894 smallmouth bass Micropterus dolomieui, and 563 channel catfish Icatalurus punctatus. Distribution, abundance and population parameters of each species were examined. One year growth, mortality, and relative year class strength was described.

Frictional behaviour and transport properties of simulated fault gouges derived from a natural CO2 reservoir

NARCIS (Netherlands)

Bakker, E.; Hangx, S.J.T.|info:eu-repo/dai/nl/30483579X; Niemeijer, A.R.|info:eu-repo/dai/nl/370832132; Spiers, C.J.|info:eu-repo/dai/nl/304829323

2016-01-01

We investigated the effects of long-term CO2-brine-rock interactions on the frictional and transport properties of reservoir-derived fault gouges, prepared from both unexposed and CO2-exposed sandstone, and from aragonite-cemented fault rock of an active CO2-leaking conduit, obtained from a natural

OPTIMIZATION OF INFILL DRILLING IN NATURALLY-FRACTURED TIGHT-GAS RESERVOIRS

Energy Technology Data Exchange (ETDEWEB)

Lawrence W. Teufel; Her-Yuan Chen; Thomas W. Engler; Bruce Hart

2004-05-01

A major goal of industry and the U.S. Department of Energy (DOE) fossil energy program is to increase gas reserves in tight-gas reservoirs. Infill drilling and hydraulic fracture stimulation in these reservoirs are important reservoir management strategies to increase production and reserves. Phase II of this DOE/cooperative industry project focused on optimization of infill drilling and evaluation of hydraulic fracturing in naturally-fractured tight-gas reservoirs. The cooperative project involved multidisciplinary reservoir characterization and simulation studies to determine infill well potential in the Mesaverde and Dakota sandstone formations at selected areas in the San Juan Basin of northwestern New Mexico. This work used the methodology and approach developed in Phase I. Integrated reservoir description and hydraulic fracture treatment analyses were also conducted in the Pecos Slope Abo tight-gas reservoir in southeastern New Mexico and the Lewis Shale in the San Juan Basin. This study has demonstrated a methodology to (1) describe reservoir heterogeneities and natural fracture systems, (2) determine reservoir permeability and permeability anisotropy, (3) define the elliptical drainage area and recoverable gas for existing wells, (4) determine the optimal location and number of new in-fill wells to maximize economic recovery, (5) forecast the increase in total cumulative gas production from infill drilling, and (6) evaluate hydraulic fracture simulation treatments and their impact on well drainage area and infill well potential. Industry partners during the course of this five-year project included BP, Burlington Resources, ConocoPhillips, and Williams.

Oligocene paleogeography of the northern Great Plains and adjacent mountains

International Nuclear Information System (INIS)

Seeland, D.

1985-01-01

Early Oligocene paleogeography of the northern Great Plains and adjacent mountains is inferred in part from published surface and subsurface studies of the pre-Oligocene surface. These studies are combined with published and unpublished information on clast provenance, crossbedding orientation, and Eocene paleogeography. The Oligocene Arctic Ocean-Gulf of Mexico continental divide extended from the southern Absaroka Mountains east along the Owl Creek Mountains, across the southern Powder River Basin, through the northern Black Hills, and eastward across South Dakota. Streams north of the divide flowed northeastward. The Olligocene White River Group contains 50 to 90 percent airfall pyroclastic debris from a northern Great Basin source. Most of the uranium deposits of the region in pre-Oligocene rocks can be related to a uranium source in the volcanic ash of the White River; in many places the pre-Oligocene deposits can be related to specific Oligocene channels. Uranium deposits in sandstones of major Oligocene rivers are an important new type of deposit. The Oligocene channel sandstones also contain small quantities of gold, molybdenum, gas, and oil

Preliminary discussion on prospecting potential for sandstone-type uranium deposits in meso-cenozoic basins, northern Ordos

International Nuclear Information System (INIS)

Di Yongqiang

2002-01-01

Characteristics of the regional stratigraphy, tectonic movement, geologic evolution and hydrogeology are briefly introduced. Using the metallogenic theory and prospecting criteria for interlayer oxidation zone sandstone-type uranium deposits, the author analyses the prospecting potential and main prospecting targets in the region, and proposes suggestions for further prospecting work as well

Area of Interest 1, CO₂ at the Interface. Nature and Dynamics of the Reservoir/Caprock Contact and Implications for Carbon Storage Performance

Energy Technology Data Exchange (ETDEWEB)

Mozley, Peter [New Mexico Institute Of Mining And Technology, Socorro, NM (United States); Evans, James [New Mexico Institute Of Mining And Technology, Socorro, NM (United States); Dewers, Thomas [New Mexico Institute Of Mining And Technology, Socorro, NM (United States)

2014-10-31

We examined the influence of geologic features present at the reservoir/caprock interface on the transmission of supercritical CO₂ into and through caprock. We focused on the case of deformation-band faults in reservoir lithologies that intersect the interface and transition to opening-mode fractures in caprock lithologies. Deformation-band faults are exceeding common in potential CO₂ injection units and our fieldwork in Utah indicates that this sort of transition is common. To quantify the impact of these interface features on flow and transport we first described the sedimentology and permeability characteristics of selected sites along the Navajo Sandstone (reservoir lithology) and Carmel Formation (caprock lithology) interface, and along the Slickrock Member (reservoir lithology) and Earthy Member (caprock lithology) of the Entrada Sandstone interface, and used this information to construct conceptual permeability models for numerical analysis. We then examined the impact of these structures on flow using single-phase and multiphase numerical flow models for these study sites. Key findings include: (1) Deformation-band faults strongly compartmentalize the reservoir and largely block cross-fault flow of supercritical CO₂. (2) Significant flow of CO₂ through the fractures is possible, however, the magnitude is dependent on the small-scale geometry of the contact between the opening-mode fracture and the deformation band fault. (3) Due to the presence of permeable units in the caprock, caprock units are capable of storing significant volumes of CO₂, particularly when the fracture network does not extend all the way through the caprock. The large-scale distribution of these deformation-bandfault-to-opening-mode-fractures is related to the curvature of the beds, with greater densities of fractures in high curvature regions. We also examined core and outcrops from the Mount Simon Sandstone and Eau Claire

Micro-Ct Imaging of Multi-Phase Flow in Carbonates and Sandstones

Science.gov (United States)

Andrew, M. G.; Bijeljic, B.; Blunt, M. J.

2013-12-01

One of the most important mechanisms that limits the escape of CO2 when injected into the subsurface for the purposes of carbon storage is capillary trapping, where CO2 is stranded as pore-scale droplets (ganglia). Prospective storage sites are aquifers or reservoirs that tend to be at conditions where CO2 will reside as a super-critical phase. In order to fully describe physical mechanisms characterising multi-phase flow during and post CO2 injection, experiments need to be conducted at these elevated aquifer/reservoir conditions - this poses a considerable experimental challenge. A novel experimental apparatus has been developed which uses μCT scanning for the non-invasive imaging of the distribution of CO2 in the pore space of rock with resolutions of 7μm at temperatures and pressures representative of the conditions present in prospective saline aquifer CO2 storage sites. The fluids are kept in chemical equilibrium with one-another and with the rock into which they are injected. This is done to prevent the dissolution of the CO2 in the brine to form carbonic acid, which can then react with the rock, particularly carbonates. By eliminating reaction we study the fundamental mechanisms of capillary trapping for an unchanging pore structure. In this study we present a suite of results from three carbonate and two sandstone rock types, showing that, for both cases the CO2 acts as the non-wetting phase and significant quantities of CO2 is trapped. The carbonate examined represent a wide variety of pore topologies with one rock with a very well connected, high porosity pore space (Mt Gambier), one with a lower porosity, poorly connected pore space (Estaillades) and one with a cemented bead pack type pore space (Ketton). Both sandstones (Doddington and Bentheimer) were high permeability granular quartzites. CO2 was injected into each rock, followed by brine injection. After brine injection the entire length of the rock core was scanned, processed and segmented into

The characteristics of ginger-like rock and its geological significance in Northern Zhungeer basin

International Nuclear Information System (INIS)

Wu Rengui

1998-01-01

The author studies the characteristics of ginger-like stratum and its genesis in northern Zhungeer basin. There are many ginger-like strata of Tertiary-Quaternary exist in northern Zhungeer basin. It shows a good prospect for the formation of Tertiary sandstone type Uranium deposit which can be leached in-situ

Experimental measurements of the SP response to concentration and temperature gradients in sandstones with application to subsurface geophysical monitoring

Science.gov (United States)

Leinov, E.; Jackson, M. D.

2014-09-01

Exclusion-diffusion potentials arising from temperature gradients are widely neglected in self-potential (SP) surveys, despite the ubiquitous presence of temperature gradients in subsurface settings such as volcanoes and hot springs, geothermal fields, and oil reservoirs during production via water or steam injection. Likewise, with the exception of borehole SP logging, exclusion-diffusion potentials arising from concentration gradients are also neglected or, at best, it is assumed that the diffusion potential dominates. To better interpret these SP sources requires well-constrained measurements of the various coupling terms. We report measurements of thermoelectric and electrochemical exclusion-diffusion potentials across sandstones saturated with NaCl brine and find that electrode effects can dominate the measured voltage. After correcting for these, we find that Hittorf transport numbers are the same within experimental error regardless of whether ion transport occurs in response to temperature or concentration gradients over the range of NaCl concentration investigated that is typical of natural systems. Diffusion potentials dominate only if the pore throat radius is more than approximately 4000 times larger than the diffuse layer thickness. In fine-grained sandstones with small pore throat diameter, this condition is likely to be met only if the saturating brine is of relatively high salinity; thus, in many cases of interest to earth scientists, exclusion-diffusion potentials will comprise significant contributions from both ionic diffusion through, and ionic exclusion from, the pore space of the rock. However, in coarse-grained sandstones, or sandstones saturated with high-salinity brine, exclusion-diffusion potentials can be described using end-member models in which ionic exclusion is neglected. Exclusion-diffusion potentials in sandstones depend upon pore size and salinity in a complex way: they may be positive, negative, or zero depending upon sandstone

Iron speciation and mineral characterization of upper Jurassic reservoir rocks in the Minhe Basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Ma, Xiangxian; Zheng, Guodong, E-mail: gdzhbj@mail.iggcas.ac.cn; Xu, Wang [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Liang, Minliang [Chinese Academy of Geological Sciences, Institute of Geomechanics, Key Lab of Shale Oil and Gas Geological Survey (China); Fan, Qiaohui; Wu, Yingzhong; Ye, Conglin [Chinese Academy of Sciences, Key Laboratory of Petroleum Resources, Gansu Province / Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics (China); Shozugawa, Katsumi; Matsuo, Motoyuki [The University of Tokyo, Graduate School of Arts and Sciences (Japan)

2016-12-15

Six samples from a natural outcrop of reservoir rocks with oil seepage and two control samples from surrounding area in the Minhe Basin, northwestern China were selectively collected and analyzed for mineralogical composition as well as iron speciation using X-ray powder diffraction (XRD) and Mössbauer spectroscopy, respectively. Iron species revealed that: (1) the oil-bearing reservoir rocks were changed by water-rock-oil interactions; (2) even in the same site, there was a different performance between sandstone and mudstone during the oil and gas infusion to the reservoirs; and (3) this was evidence indicating the selective channels of hydrocarbon migration. In addition, these studies showed that the iron speciation by Mössbauer spectroscopy could be useful for the study of oil and gas reservoirs, especially the processes of the water-rock interactions within petroleum reservoirs.

The role of mineral heterogeneity on the hydrogeochemical response of two fractured reservoir rocks in contact with dissolved CO2

Science.gov (United States)

Garcia Rios, Maria; Luquot, Linda; Soler, Josep M.; Cama, Jordi

2017-04-01

In this study we compare the hydrogeochemical response of two fractured reservoir rocks (limestone composed of 100 wt.% calcite and sandstone composed of 66 wt.% calcite, 28 wt.% quartz and 6 wt.% microcline) in contact with CO2-rich sulfate solutions. Flow-through percolation experiments were performed using artificially fractured limestone and sandstone cores and injecting a CO2-rich sulfate solution under a constant volumetric flow rate (from 0.2 to 60 mL/h) at P = 150 bar and T = 60 °C. Measurements of the pressure difference between the inlet and the outlet of the samples and of the aqueous chemistry enabled the determination of fracture permeability changes and net reaction rates. Additionally, X-ray computed microtomography (XCMT) was used to characterize and localized changes in fracture volume induced by dissolution and precipitation reactions. In all reacted cores an increase in fracture permeability and in fracture volume was always produced even when gypsum precipitation happened. The presence of inert silicate grains in sandstone samples favored the occurrence of largely distributed dissolution structures in contrast to localized dissolution in limestone samples. This phenomenon promoted greater dissolution and smaller precipitation in sandstone than in limestone experiments. As a result, in sandstone reservoirs, the larger increase in fracture volume as well as the more extended distribution of the created volume would favor the CO2 storage capacity. The different distribution of created volume between limestone and sandstone experiments led to a different variation in fracture permeability. The progressive stepped permeability increase for sandstone would be preferred to the sharp permeability increase for limestone to minimize risks related to CO2 injection, favor capillary trapping and reduce energetic storage costs. 2D reactive transport simulations that reproduce the variation in aqueous chemistry and the fracture geometry (dissolution pattern

Sandstone-body and shale-body dimensions in a braided fluvial system: Salt wash sandstone member (Morrison formation), Garfield County, Utah

Science.gov (United States)

Robinson, J.W.; McCabea, P.J.

1997-01-01

Excellent three-dimensional exposures of the Upper Jurassic Salt Wash Sandstone Member of the Morrison Formation in the Henry Mountains area of southern Utah allow measurement of the thickness and width of fluvial sandstone and shale bodies from extensive photomosaics. The Salt Wash Sandstone Member is composed of fluvial channel fill, abandoned channel fill, and overbank/flood-plain strata that were deposited on a broad alluvial plain of low-sinuosity, sandy, braided streams flowing northeast. A hierarchy of sandstone and shale bodies in the Salt Wash Sandstone Member includes, in ascending order, trough cross-bedding, fining-upward units/mudstone intraclast conglomerates, singlestory sandstone bodies/basal conglomerate, abandoned channel fill, multistory sandstone bodies, and overbank/flood-plain heterolithic strata. Trough cross-beds have an average width:thickness ratio (W:T) of 8.5:1 in the lower interval of the Salt Wash Sandstone Member and 10.4:1 in the upper interval. Fining-upward units are 0.5-3.0 m thick and 3-11 m wide. Single-story sandstone bodies in the upper interval are wider and thicker than their counterparts in the lower interval, based on average W:T, linear regression analysis, and cumulative relative frequency graphs. Multistory sandstone bodies are composed of two to eight stories, range up to 30 m thick and over 1500 m wide (W:T > 50:1), and are also larger in the upper interval. Heterolithic units between sandstone bodies include abandoned channel fill (W:T = 33:1) and overbank/flood-plain deposits (W:T = 70:1). Understanding W:T ratios from the component parts of an ancient, sandy, braided stream deposit can be applied in several ways to similar strata in other basins; for example, to (1) determine the width of a unit when only the thickness is known, (2) create correlation guidelines and maximum correlation lengths, (3) aid in interpreting the controls on fluvial architecture, and (4) place additional constraints on input variables to

Geology and oil and gas assessment of the Todilto Total Petroleum System, San Juan Basin Province, New Mexico and Colorado: Chapter 3 in Total petroleum systems and geologic assessment of undiscovered oil and gas resources in the San Juan Basin Province, exclusive of Paleozoic rocks, New Mexico and Colorado

Science.gov (United States)

Ridgley, J.L.; Hatch, J.R.

2013-01-01

Organic-rich, shaly limestone beds, which contain hydrocarbon source beds in the lower part of the Jurassic Todilto Limestone Member of the Wanakah Formation, and sandstone reservoirs in the overlying Jurassic Entrada Sandstone, compose the Todilto Total Petroleum System (TPS). Source rock facies of the Todilto Limestone were deposited in a combined marine-lacustrine depositional setting. Sandstone reservoirs in the Entrada Sandstone were deposited in eolian depositional environments. Oil in Todilto source beds was generated beginning in the middle Paleocene, about 63 million years ago, and maximum generation of oil occurred in the middle Eocene. In the northern part of the San Juan Basin, possible gas and condensate were generated in Todilto Limestone Member source beds until the middle Miocene. The migration distance of oil from the Todilto source beds into the underlying Entrada Sandstone reservoirs was short, probably within the dimensions of a single dune crest. Traps in the Entrada are mainly stratigraphic and diagenetic. Regional tilt of the strata to the northeast has influenced structural trapping of oil, but also allowed for later introduction of water. Subsequent hydrodynamic forces have influenced the repositioning of the oil in some reservoirs and flushing in others. Seals are mostly the anhydrite and limestone facies of the Todilto, which thin to as little as 10 ft over the crests of the dunes. The TPS contains only one assessment unit, the Entrada Sandstone Conventional Oil Assessment Unit (AU) (50220401). Only four of the eight oil fields producing from the Entrada met the 0.5 million barrels of oil minimum size used for this assessment. The AU was estimated at the mean to have potential additions to reserves of 2.32 million barrels of oil (MMBO), 5.56 billion cubic feet of natural gas (BCFG), and 0.22 million barrels of natural gas liquids (MMBNGL).

The influence of clay minerals on acoustic properties of sandstones

Energy Technology Data Exchange (ETDEWEB)

Hansen, Olav

1997-12-31

This thesis aims to provide better understanding of the relationship between the acoustic properties and the petrophysical/mineralogical properties in sand-prone rock. It emphasizes the influence of clay minerals. The author develops a method to deposit clay minerals/mineral aggregates in pore space of a rigid rock framework. Kaolinite aggregates were flushed into porous permeable Bentheimer sandstone to evaluate the effect of pore filling minerals on porosity, permeability and acoustic properties. The compressional velocity was hardly affected by the clay content and it was found that the effect of minor quantities of pore filling minerals may be acoustically modelled as an ideal suspension, where the pore fluid bulk modulus is modified by the bulk modulus of the clay minerals. The influence of clays on acoustic velocities in petroleum reservoir rocks was investigated through ultrasonic measurements of compressional- and shear-waves on core material from reservoir and non-reservoir units on the Norwegian Continental Shelf. The measured velocities decrease as the porosity increases, but are not strongly dependent on the clay content. The measured velocities are less dependent on the petrophysical and lithological properties than indicated by previous authors and published mathematical models, and stiffness reduction factors are introduced in two of the models to better match the data. Velocities are estimated along the wellbores based on non-sonic well logs and reflect well the actual sonic log well measurements. In some wells the compressional velocity cannot be modelled correctly by the models suggested. Very high compressional wave anisotropy was measured in the dry samples at atmospheric conditions. As the samples were saturated, the anisotropy was reduced to a maximum of about 30% and decreases further upon pressurization. Reservoir rocks retrieved from 2500 m are more stress dependent than those retrieved from less than 200 m depth. 168 refs., 117 figs., 24

Optimising inflow performance of a long multi-lateral offshore well in low permeability, gas-bearing sandstone: K14-FB 102 case study

Energy Technology Data Exchange (ETDEWEB)

Hands, N. [Shell Canada Ltd., Calgary, AB (Canada); Francis, P. [Shell International Exploration and Production (Netherlands); Whittle, A.; Rajasingam, D. [NAM B. V. (Netherlands)

1998-12-31

Successful completion of the sub-horizontal dual-lateral well, K14-FB 102, to optimize production capacity and reservoir drainage in an offshore gas play in the Dutch sector of the North Sea is described. The two 5-7/8 inch horizontal production intervals were drilled and completed using a rheologically engineered, minimal solids, non-damaging sodium formate brine- based fluid designed as a drill-in fluid for reservoir intervals. The completion was made possible by the selection of the appropriate reservoir drill-in and completion fluid, appropriate level of contingency planning and a fully integrated team approach and custom-made well solution. Inflow performance has matched the performance of cemented and high-performance wells at a much lower cost. It was found that openhole reservoir completion techniques offer relatively inexpensive `fit-for-purpose` well solutions for low permeability sandstone in this region of the North Sea.3 refs., 6 tabs., 7 figs.

Interdisciplinary study of reservoir compartments and heterogeneity. Final report, October 1, 1993--December 31, 1996

Energy Technology Data Exchange (ETDEWEB)

Van Kirk, C.

1998-01-01

A case study approach using Terry Sandstone production from the Hambert-Aristocrat Field, Weld County, Colorado was used to document the process of integration. One specific project goal is to demonstrate how a multidisciplinary approach can be used to detect reservoir compartmentalization and improve reserve estimates. The final project goal is to derive a general strategy for integration for independent operators. Teamwork is the norm for the petroleum industry where teams of geologists, geophysicists, and petroleum engineers work together to improve profits through a better understanding of reservoir size, compartmentalization, and orientation as well as reservoir flow characteristics. In this manner, integration of data narrows the uncertainty in reserve estimates and enhances reservoir management decisions. The process of integration has proven to be iterative. Integration has helped identify reservoir compartmentalization and reduce the uncertainty in the reserve estimates. This research report documents specific examples of integration and the economic benefits of integration.

The Paleozoic-Mesozoic recycling of the Rakaia Terrane, South Island, New Zealand : sandstone clast and sandstone petrology, geochemistry, and geochronology

International Nuclear Information System (INIS)

Wandres, A.M.; Bradshaw, J.D.; Ireland, T.

2005-01-01

The Torlesse terranes - part of the New Zealand Eastern Province - are accretionary complexes that comprise an enormous volume of quartzofeldspathic sandstones and mudstones with subsidiary conglomerates plus minor oceanic assemblages. Two terranes are recognised in the South Island - the Permian to Late Triassic Rakaia Terrane and the Late Jurassic to Early Cretaceous Pahau Terrane. Sandstone clasts from two Rakaia Terrane and two Pahau Terrane conglomerates were collected. We present the first combined detailed information on petrography and geochemistry of Torlesse conglomerate sandstone clasts and use our own and published U-Pb SHRIMP detrital zircon age data to demonstrate the recycling of the Rakaia Terrane into Rakaia strata itself and into Pahau Terrane strata. Sandstone clast major and trace element chemical data largely support petrographic observations derived from thin-section analysis. The similarities of petrographic and geochemical data between sandstone clasts from the Rakaia Terrane and Rakaia sandstones suggest that clasts in the Permian Te Moana and Late Triassic Lake Hill Conglomerates were derived by autocannibalistic reworking of older, consolidated, Rakaia sediments. Data from sandstone clasts from the Pahau Terrane suggest that uplift of the Rakaia Terrane continued into the Cretaceous. These Pahau Terrane clasts indicate that at the time of the Pahau sedimentation Permian to early Late Triassic Rakaia rocks were exposed and recycled into the Pahau Basin. (author). 57 refs., 8 figs., 3 tables

Pore Structure and Limit Pressure of Gas Slippage Effect in Tight Sandstone

Science.gov (United States)

You, Lijun; Xue, Kunlin; Kang, Yili; Liao, Yi

2013-01-01

Gas slip effect is an important mechanism that the gas flow is different from liquid flow in porous media. It is generally considered that the lower the permeability in porous media is, the more severe slip effect of gas flow will be. We design and then carry out experiments with the increase of backpressure at the outlet of the core samples based on the definition of gas slip effect and in view of different levels of permeability of tight sandstone reservoir. This study inspects a limit pressure of the gas slip effect in tight sandstones and analyzes the characteristic parameter of capillary pressure curves. The experimental results indicate that gas slip effect can be eliminated when the backpressure reaches a limit pressure. When the backpressure exceeds the limit pressure, the measured gas permeability is a relatively stable value whose range is less than 3% for a given core sample. It is also found that the limit pressure increases with the decreasing in permeability and has close relation with pore structure of the core samples. The results have an important influence on correlation study on gas flow in porous medium, and are beneficial to reduce the workload of laboratory experiment. PMID:24379747

The Holocene Sedimentation in Sandstone Rockshelters of Northern Bohemia

Czech Academy of Sciences Publication Activity Database

Cílek, Václav

2000-01-01

Roč. 11, - (2000), s. 66-69 ISSN 1210-9606. [International Conference on Past Global Changes Upper Pleistocene and Holocene Climatic Variations. Prague, 06.09.2000-09.09.2000] Grant - others:US(XC) National Geographic Society 6330-98 "The last foragers of the Northern Europe" Institutional research plan: CEZ:AV0Z3013912 Subject RIV: DB - Geology ; Mineralogy http://geolines.gli.cas.cz/fileadmin/volumes/volume11/G11-066.pdf

Experimental studies of low salinity water flooding in carbonate reservoirs: A new promising approach

DEFF Research Database (Denmark)

Zahid, Adeel; Shapiro, Alexander; Skauge, Arne

2012-01-01

Low salinity water flooding is well studied for sandstone reservoirs, both laboratory and field tests have showed improvement in the oil recovery in many cases. Up to very recently, the low salinity effect has been indeterminated for carbonates. Most recently, Saudi Aramco reported that substantial...... additional oil recovery can be achieved when successively flooding composite carbonate core plugs with various diluted versions of seawater. The experimental data on carbonates is very limited, so more data and better understanding of the mechanisms involved is needed to utilize this method for carbonate...... reservoirs. In this paper, we have experimentally investigated the oil recovery potential of low salinity water flooding for carbonate rocks. We used both reservoir carbonate and outcrop chalk core plugs. The flooding experiments were carried out initially with the seawater, and afterwards additional oil...

An Integrated Rock Typing Approach for Unraveling the Reservoir Heterogeneity of Tight Sands in the Whicher Range Field of Perth Basin, Western Australia

DEFF Research Database (Denmark)

Ilkhchi, Rahim Kadkhodaie; Rezaee, Reza; Harami, Reza Moussavi

2014-01-01

Tight gas sands in Whicher Range Field of Perth Basin show large heterogeneity in reservoir characteristics and production behavior related to depositional and diagenetic features. Diagenetic events (compaction and cementation) have severely affected the pore system. In order to investigate...... the petrophysical characteristics, reservoir sandstone facies were correlated with core porosity and permeability and their equivalent well log responses to describe hydraulic flow units and electrofacies, respectively. Thus, very tight, tight, and sub-tight sands were differentiated. To reveal the relationship...... between pore system properties and depositional and diagenetic characteristics in each sand type, reservoir rock types were extracted. The identified reservoir rock types are in fact a reflection of internal reservoir heterogeneity related to pore system properties. All reservoir rock types...

Sandstone Turning by Abrasive Waterjet

Czech Academy of Sciences Publication Activity Database

Hlaváček, Petr; Cárach, J.; Hloch, Sergej; Vasilko, K.; Klichová, Dagmar; Klich, Jiří; Lehocká, D.

2015-01-01

Roč. 48, č. 6 (2015), s. 2489-2493 ISSN 0723-2632 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : turning away from the jet * conventional turning towards the jet * sandstone * abrasive water jet Subject RIV: JQ - Machines ; Tools Impact factor: 2.386, year: 2015 http://www.springerprofessional.de/sandstone-turning-by-abrasive-waterjet/6038028.html

Geological characteristic of the main oil and gas producing formations of the upper Austrian molasse basin. Pt. 1. The Eocene sandstones

Energy Technology Data Exchange (ETDEWEB)

Wagner, L [Rohoel-Aufsuchungs-Gesellschaft m.b.H., Vienna (Austria)

1980-09-01

The sandstones of the Upper Eocene are the main oil carriers within RAG's Upper Austrian concession area. The attempt is being made to reconstruct the paleogeography of the Eocene-in which time the sea transgressed the Molasse basin towards N and E - from core and log evidence. From deep Lower Tertiary onwards the mesozoic and older sediments were exposed to intensive erosion, which resulted in a slightly undulating peneplane sloping in a S to SW direction. This erosion plane was - still in Lower Tertiary times - in some areas dissected into horst and graben structures which greatly influenced the deposition of the early Eocene sediments. During the Upper Eocene the Molasse basin began to subside and subsided more strongly in the SW than in the N and NE, so that neritic deposits could form in the first area, whereas lagoonal and brackish sedimentation still prevailed in the latter. The Eocene sandstones are being classified according to their environment of deposition, and their reservoir, characteristics are being studied. Sandstones are absent in the neritic environment of the Discocyclina-marls only. Sand deposits have been encountered as: 1) transgressive horizons directly overlying the pretertiary substrate, 2) infills of channels cut into limnic-brackish sediments, 3) littoral deposits, partly interfingering with Lithothamnium limestone, 4) fine grained sandy marls and nummulitic sandstones within sublittoral to neritic sediments.

Simulation of the mulltizones clastic reservoir: A case study of Upper Qishn Clastic Member, Masila Basin-Yemen

Science.gov (United States)

Khamis, Mohamed; Marta, Ebrahim Bin; Al Natifi, Ali; Fattah, Khaled Abdel; Lashin, Aref

2017-06-01

The Upper Qishn Clastic Member is one of the main oil-bearing reservoirs that are located at Masila Basin-Yemen. It produces oil from many zones with different reservoir properties. The aim of this study is to simulate and model the Qishn sandstone reservoir to provide more understanding of its properties. The available, core plugs, petrophysical, PVT, pressure and production datasets, as well as the seismic structural and geologic information, are all integrated and used in the simulation process. Eclipse simulator was used as a powerful tool for reservoir modeling. A simplified approach based on a pseudo steady-state productivity index and a material balance relationship between the aquifer pressure and the cumulative influx, is applied. The petrophysical properties of the Qishn sandstone reservoir are mainly investigated based on the well logging and core plug analyses. Three reservoir zones of good hydrocarbon potentiality are indicated and named from above to below as S1A, S1C and S2. Among of these zones, the S1A zone attains the best petrophysical and reservoir quality properties. It has an average hydrocarbon saturation of more than 65%, high effective porosity up to 20% and good permeability record (66 mD). The reservoir structure is represented by faulted anticline at the middle of the study with a down going decrease in geometry from S1A zone to S2 zone. It is limited by NE-SW and E-W bounding faults, with a weak aquifer connection from the east. The analysis of pressure and PVT data has revealed that the reservoir fluid type is dead oil with very low gas liquid ratio (GLR). The simulation results indicate heterogeneous reservoir associated with weak aquifer, supported by high initial water saturation and high water cut. Initial oil in place is estimated to be around 628 MM BBL, however, the oil recovery during the period of production is very low (<10%) because of the high water cut due to the fractures associated with many faults. Hence, secondary and

Constitutive Modelling and Deformation Band Angle Predictions for High Porosity Sandstones

Science.gov (United States)

Richards, M. C.; Issen, K. A.; Ingraham, M. D.

2017-12-01

The development of a field-scale deformation model requires a constitutive framework that is capable of representing known material behavior and able to be calibrated using available mechanical response data. This work employs the principle of hyperplasticity (e.g., Houlsby and Puzrin, 2006) to develop such a constitutive framework for high porosity sandstone. Adapting the works of Zimmerman et al. (1986) and Collins and Houlsby (1997), the mechanical data set of Ingraham et al. (2013 a, b) was used to develop a specific constitutive framework for Castlegate sandstone, a high porosity fluvial-deposited reservoir analog rock. Using the mechanical data set of Ingraham et al. (2013 a, b), explicit expressions and material parameters of the elastic moduli and strain tensors were obtained. With these expressions, analytical and numerical techniques were then employed to partition the total mechanical strain into elastic, coupled, and plastic strain components. With the partitioned strain data, yield surfaces in true-stress space, coefficients of internal friction, dilatancy factors, along with the theorectical predictions of the deformation band angles were obtained. These results were also evaluated against band angle values obtained from a) measurements on specimen jackets (Ingraham et al., 2013a), b) plane fits through located acoustic emissions (AE) events (Ingraham et al. 2013b), and c) X-ray micro-computed tomography (micro-CT) calculations.

Predicting permeability of low enthalpy geothermal reservoirs: A case study from the Upper Triassic − Lower Jurassic Gassum Formation, Norwegian–Danish Basin

DEFF Research Database (Denmark)

Weibel, Rikke; Olivarius, Mette; Kristensen, Lars

2017-01-01

This paper aims at improving the predictability of permeability in low enthalpy geothermal reser-voirs by investigating the effect of diagenesis on sandstone permeability. Applying the best fittedporosity–permeability trend lines, obtained from conventional core analysis, to log-interpreted poros...

Regional distribution regularity of sandstone uranium deposits in Asian continent and prospecting strategy for sandstone uranium deposits in China

International Nuclear Information System (INIS)

Chen Zuyi

2002-01-01

Since the 1980's, after the discovery of numerous sandstone uranium deposits in Middle Asia (Kazakhstan, Uzbekistan) many large sandstone uranium deposits have been found in both Russia and Mongolia. So that Asia has become the most concentrated region of sandstone uranium deposits. The known sandstone uranium deposits occur mostly in a arcual tectonic belt constrained from the north by the Siberian continental block, and the Tarim-North China continental block from the south. This belt is named by Russian geologists as the Central Asian Mobile Belt, and some Chinese geologists call it the 'Mongolian Arc'. A lot of large and super large metallic, non-metallic, gold, polymetallic, porphyry copper and gold, massive sulphide and uranium deposits (of sandstone and volcanic types) with different origin and various types concentrated occur in this belt. The abundant and colourful mineral resources in the region are closely associated with the specific geologic-tectonic evolution of the above belt. It is necessary to strengthen the detailed geologic research and uranium prospecting in the region

Dynamic fluid connectivity during steady-state multiphase flow in a sandstone.

Science.gov (United States)

Reynolds, Catriona A; Menke, Hannah; Andrew, Matthew; Blunt, Martin J; Krevor, Samuel

2017-08-01

The current conceptual picture of steady-state multiphase Darcy flow in porous media is that the fluid phases organize into separate flow pathways with stable interfaces. Here we demonstrate a previously unobserved type of steady-state flow behavior, which we term "dynamic connectivity," using fast pore-scale X-ray imaging. We image the flow of N 2 and brine through a permeable sandstone at subsurface reservoir conditions, and low capillary numbers, and at constant fluid saturation. At any instant, the network of pores filled with the nonwetting phase is not necessarily connected. Flow occurs along pathways that periodically reconnect, like cars controlled by traffic lights. This behavior is consistent with an energy balance, where some of the energy of the injected fluids is sporadically converted to create new interfaces.

Discussion on the origin of bleached sandstone of Qianjiadian uranium deposit

International Nuclear Information System (INIS)

Pang Yaqing; Xiang Weidong; Li Tiangang; Chen Xiaolin; Xia Yuliang

2007-01-01

Qianjiadian uranium deposit is a sandstone-type uranium deposit that has been discovered in Songliao Basin in recent years. Uranium ore bodies are planar or lenticular in shape and under the control of the contact between gray sandstones and bleached sandstones. The bleached sandstone is white in color, cemented loosely, nearly without TOC and pyrite contained and rich in uranium. Geochemical characteristics and types and assemblages of clay minerals of the bleached sandstone reveal that the bleached sandstone is the product of oxidation of the interlayer oxidation zone, and it is a part of the interlayer oxidation zone. The main reasons for white color of the bleached sandstone are transfer of iron ion, oxidation of TOC and kaolinization of sandstone. (authors)

Architecture and reservoir quality of low-permeable Eocene lacustrine turbidite sandstone from the Dongying Depression, East China

Science.gov (United States)

Munawar, Muhammad Jawad; Lin, Chengyan; Chunmei, Dong; Zhang, Xianguo; Zhao, Haiyan; Xiao, Shuming; Azeem, Tahir; Zahid, Muhammad Aleem; Ma, Cunfei

2018-05-01

The architecture and quality of lacustrine turbidites that act as petroleum reservoirs are less well documented. Reservoir architecture and multiscale heterogeneity in turbidites represent serious challenges to production performance. Additionally, establishing a hierarchy profile to delineate heterogeneity is a challenging task in lacustrine turbidite deposits. Here, we report on the turbidites in the middle third member of the Eocene Shahejie Formation (Es3), which was deposited during extensive Middle to Late Eocene rifting in the Dongying Depression. Seismic records, wireline log responses, and core observations were integrated to describe the reservoir heterogeneity by delineating the architectural elements, sequence stratigraphic framework and lithofacies assemblage. A petrographic approach was adopted to constrain microscopic heterogeneity using an optical microscope, routine core analyses and X-ray diffraction (XRD) analyses. The Es3m member is interpreted as a sequence set composed of four composite sequences: CS1, CS2, CS3 and CS4. A total of forty-five sequences were identified within these four composite sequences. Sand bodies were mainly deposited as channels, levees, overbank splays, lobes and lobe fringes. The combination of fining-upward and coarsening-upward lithofacies patterns in the architectural elements produces highly complex composite flow units. Microscopic heterogeneity is produced by diagenetic alteration processes (i.e., feldspar dissolution, authigenic clay formation and quartz cementation). The widespread kaolinization of feldspar and mobilization of materials enhanced the quality of the reservoir by producing secondary enlarged pores. In contrast, the formation of pore-filling authigenic illite and illite/smectite clays reduced its permeability. Recovery rates are higher in the axial areas and smaller in the marginal areas of architectural elements. This study represents a significant insight into the reservoir architecture and

Core Flooding Experiments and Reactive Transport Modeling of Seasonal Heat Storage in the Hot Deep Gassum Sandstone Formation

DEFF Research Database (Denmark)

Holmslykke, Hanne D.; Kjøller, Claus; Fabricius, Ida Lykke

2017-01-01

Seasonal storage of excess heat in hot deep aquifers is considered to optimize the usage of commonly available energy sources. The chemical effects of heating the Gassum Sandstone Formation to up to 150 degrees C is investigated by combining laboratory core flooding experiments with petrographic ...... minor effects on the properties of the reservoir and that storage of excess heat in the Gassum Formation in the Stenlille area may be possible provided operational precautions are taken....... analysis and geochemical modeling. Synthetic formation water is injected into two sets of Gassum Formation samples at 25, 50 (reservoir temperature), 100, and 150 degrees C with a velocity of 0.05 and 0.1 PV/h, respectively. Results show a significant increase in the aqueous concentration of silicium...... and iron with increasing temperature due to dissolution of silica and siderite. Increasing the reservoir temperature from 50 to 100 degrees C enhanced the naturally occurring weathering of Na-rich feldspar to kaolinite. Dissolution of quartz increased sharply above 100 degrees C and was the dominating...

Deformation bands in porous sandstone: case study in basins of northeast Brazil; Bandas de deformacao em arenitos porosos: estudo de casos em bacias do nordeste do Brasil

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Talles Souza [PETROBRAS, RN (Brazil). Interpretacao e Avaliacao de bacias da Costa Leste do Brasil E and P. Gerencia de Interpretacao], e-mail: tallesferreira@petrobras.com.br; Silva, Fernando Cesar Alves da [Universidade Federal do Rio Grande do Norte (UFRN). Dept. de Geologia Programa de Pos-Graduacao em Geodinamica e Geofisica (Brazil)], e-mail: fernando@geologia.ufrn.br

2010-05-15

The meso and microscopic scale sandstone characterizations of the deformation bands of three sedimentary basins in northeastern Brazil; the Potiguar and Sergipe-Alagoas basins (Brazilian Atlantic Margin) and the Tucano Basin (aborted rift basin) were compared for their similarities and differences. Deformation bands are structures commonly developed in porous sandstones that make up the main reservoir-rock in siliciclastic petroleum systems. These structures influence the permo-porous properties and consequently the migration pathway into a sandstone reservoir. To understand their formation process and development has been the focus of a great number of articles in recent petroleum geology literature. This study highlights the similarities and the differences in the features and deformation mechanisms that provoked the development of deformation bands in the damage zones of major faults in three different sedimentary basins. In terms of basin tectonics, the deformation bands' formation and geometric arrangements are associated with major structures. In the case of the Acu Formation, a correlation was observed with the dextral Afonso Bezerra fault system, whereas in the Sergipe-Alagoas Basin the normal dextral strike-slip faults can be associated with the faulting of the boarder basin. In the Tucano Basin case, the deformation basins are related to the Jeremoabo transpressional fault, a major structure a few kilometers to the north. This study applies structural geology tools to better understand the geometric arrangement and growing mechanisms of deformation bands in different lithological and tectonic settings. Although the deformation bands present a similar aspect in a macroscopic view, the interplay between depositional and mineralogical parameters of the host rock, as well as the basin's burial and tectonic history resulted in the development of different sandstone deformation bands in three northeastern brazilian basins. (author)

Core Flooding Experiments and Reactive Transport Modeling of Seasonal Heat Storage in the Hot Deep Gassum Sandstone Formation

DEFF Research Database (Denmark)

Holmslykke, Hanne D.; Kjøller, Claus; Fabricius, Ida Lykke

2017-01-01

Seasonal storage of excess heat in hot deep aquifers is considered to optimize the usage of commonly available energy sources. The chemical effects of heating the Gassum Sandstone Formation to up to 150 degrees C is investigated by combining laboratory core flooding experiments with petrographic...... analysis and geochemical modeling. Synthetic formation water is injected into two sets of Gassum Formation samples at 25, 50 (reservoir temperature), 100, and 150 degrees C with a velocity of 0.05 and 0.1 PV/h, respectively. Results show a significant increase in the aqueous concentration of silicium...

Real-time detection of dielectric anisotropy or isotropy in unconventional oil-gas reservoir rocks supported by the oblique-incidence reflectivity difference technique.

Science.gov (United States)

Zhan, Honglei; Wang, Jin; Zhao, Kun; Lű, Huibin; Jin, Kuijuan; He, Liping; Yang, Guozhen; Xiao, Lizhi

2016-12-15

Current geological extraction theory and techniques are very limited to adequately characterize the unconventional oil-gas reservoirs because of the considerable complexity of the geological structures. Optical measurement has the advantages of non-interference with the earth magnetic fields, and is often useful in detecting various physical properties. One key parameter that can be detected using optical methods is the dielectric permittivity, which reflects the mineral and organic properties. Here we reported an oblique-incidence reflectivity difference (OIRD) technique that is sensitive to the dielectric and surface properties and can be applied to characterization of reservoir rocks, such as shale and sandstone core samples extracted from subsurface. The layered distribution of the dielectric properties in shales and the uniform distribution in sandstones are clearly identified using the OIRD signals. In shales, the micro-cracks and particle orientation result in directional changes of the dielectric and surface properties, and thus, the isotropy and anisotropy of the rock can be characterized by OIRD. As the dielectric and surface properties are closely related to the hydrocarbon-bearing features in oil-gas reservoirs, we believe that the precise measurement carried with OIRD can help in improving the recovery efficiency in well-drilling process.

Lithofacies Architecturing and Hydrocarbon Reservoir Potential of Lumshiwal Formation: Surghar Range, Trans-Indus Ranges, North Pakistan

Directory of Open Access Journals (Sweden)

Iftikhar Alam

2015-12-01

directed Paleo-current system prevailed during deposition of Lumshiwal Formation. Diagenetic and tectonically induced fractures make the formation exceedingly porous and permeable as suitable reservoir horizon for the accumulation of hydrocarbon in the Trans-Indus ranges. The same formation has already been proven as potential reservoir horizon for hydrocarbon in the Kohat Plateau of northwest Pakistan. Secondly, the formation is dominantly comprised of silica/quartz sandstone (quartzarenite which can be used as silica sand, one of the essential raw materials for glass industries. The formation is also comprised of local coal seams which can be mined for production of coal in the region.

The Potential of a Surfactant/Polymer Flood in a Middle Eastern Reservoir

Directory of Open Access Journals (Sweden)

Meshal Algharaib

2012-01-01

Full Text Available An integrated full-field reservoir simulation study has been performed to determine the reservoir management and production strategies in a mature sandstone reservoir. The reservoir is a candidate for an enhanced oil recovery process or otherwise subject to abandonment. Based on its charateristics, the reservoir was found to be most suited for a surfactant/polymer (SP flood. The study started with a large data gathering and the building of a full-field three-dimensional geological model. Subsequently, a full field simulation model was built and used to history match the water flood. The history match of the water flood emphasizes the areas with remaining high oil saturations, establishes the initial condition of the reservoir for an SP flood, and generates a forecast of reserves for continued water flood operations. A sector model was constructed from the full field model and then used to study different design parameters to maximize the project profitability from the SP flood. An economic model, based on the estimated recovery, residual oil in-place, oil price, and operating costs, has been implemented in order to optimize the project profitability. The study resulted in the selection of surfactant and polymer concentrations and slug size that yielded the best economic returns when applied in this reservoir. The study shows that, in today’s oil prices, surfactant/polymer flood when applied in this reservoir has increased the ultimate oil recovery and provide a significant financial returns.

The Influence of fold and fracture development on reservoir behavior of the Lisburne Group of northern Alaska

Energy Technology Data Exchange (ETDEWEB)

Wesley K. Wallace; Catherine L. Hanks; Jerry Jensen: Michael T. Whalen; Paul Atkinson; Joseph Brinton; Thang Bui; Margarete Jadamec; Alexandre Karpov; John Lorenz; Michelle M. McGee; T.M. Parris; Ryan Shackleton

2004-07-01

The Carboniferous Lisburne Group is a major carbonate reservoir unit in northern Alaska. The Lisburne is folded and thrust faulted where it is exposed throughout the Brooks Range, but is relatively undeformed in areas of current production in the subsurface of the North Slope. The objectives of this study were to develop a better understanding of four major aspects of the Lisburne: (1) The geometry and kinematics of folds and their truncation by thrust faults. (2) The influence of folding on fracture patterns. (3) The influence of deformation on fluid flow. (4) Lithostratigraphy and its influence on folding, faulting, fracturing, and reservoir characteristics. Symmetrical detachment folds characterize the Lisburne in the northeastern Brooks Range. In contrast, Lisburne in the main axis of the Brooks Range is deformed into imbricate thrust sheets with asymmetrical hangingwall anticlines and footwall synclines. The Continental Divide thrust front separates these different structural styles in the Lisburne and also marks the southern boundary of the northeastern Brooks Range. Field studies were conducted for this project during 1999 to 2001 in various locations in the northeastern Brooks Range and in the vicinity of Porcupine Lake, immediately south of the Continental Divide thrust front. Results are summarized below for the four main subject areas of the study.

Microstructure parameters evaluation of Botucatu formation sandstone by X-ray microtomography

Energy Technology Data Exchange (ETDEWEB)

Fernandes, Jaquiel S.; Appoloni, Carlos R.; Marques, Leonardo C., E-mail: jaquielfernandes@yahoo.com.b, E-mail: appoloni@uel.b, E-mail: leocarma@yahoo.com.b [Universidade Estadual de Londrina (UEL), PR (Brazil). Dept. de Fisica. Lab. de Fisica Nuclear Aplicada; Fernandes, Celso P., E-mail: celso@lmpt.ufsc.b [Universidade Federal de Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. de Engenharia Mecanica. Lab. de Meios Porosos e Propriedades TermoFisicas (LMPT)

2009-07-01

Microstructural parameters evaluation of reservoir rocks are very important to petroleum industry. This work presents total porosity and pore size distribution measurement of a silicified sandstone sample from the Botucatu formation, collected at municipal district of Faxinal, Parana, Brazil. Porosity and pores size distribution were determined using X-Ray microtomography and imaging techniques. Acquired images had 2.9 mum spatial resolution. 800 2-D images where reconstructed for the microstructure analysis. The determined average porosity was 6.1 +- 2.1 %. 95 % of the porous phase refers to pores with radius ranging from 2.9 to 167.4 mum, presenting the larger frequency (6 %) at 5.9 mum radius. The 3-D volume of the sample was reconstructed and compared with the 3-D model obtained through the autocorrelation functions from the 2-D images analysis. (author)

Quantification of oil recovery efficiency, CO 2 storage potential, and fluid-rock interactions by CWI in heterogeneous sandstone oil reservoirs

DEFF Research Database (Denmark)

Seyyedi, Mojtaba; Sohrabi, Mehran; Sisson, Adam

2017-01-01

Significant interest exists in improving recovery from oil reservoirs while addressing concerns about increasing CO2 concentrations in the atmosphere. The combination of Enhanced Oil Recovery (EOR) and safe geologic storage of CO2 in oil reservoirs is appealing and can be achieved by carbonated (CO...... for oil recovery and CO2 storage potential on heterogeneous cores. Since not all the oil reservoirs are homogenous, understanding the potential of CWI as an integrated EOR and CO2 storage scenario in heterogeneous oil reservoirs is essential....

Full-scale laboratory drilling tests on sandstone and dolomite. Final report

Energy Technology Data Exchange (ETDEWEB)

Black, A. D.; Green, S. J.; Rogers, L. A.

1977-08-01

Full-scale laboratory drilling experiments were performed under simulated downhole conditions to determine what effect changing various drilling parameters has on penetration rate. The two rock types, typical of deep oil and gas reservoirs, used for the tests were Colton Sandstone and Bonne Terre Dolomite. Drilling was performed with standard 7/sup 7///sub 8/ inch rotary insert bits and water base mud. The results showed the penetration rate to be strongly dependent on bit weight, rotary speed and borehole mud pressure. There was only a small dependence on mud flow rate. The drilling rate decreased rapidly with increasing borehole mud pressure for borehole pressures up to about 2,000 psi. Above this pressure, the borehole pressure and rotary speeds had a smaller effect on penetration rate. The penetration rate was then dependent mostly on the bit weight. Penetration rate per horsepower input was also shown to decrease at higher mud pressures and bit weights. The ratio of horizontal confining stress to axial overburden stress was maintained at 0.7 for simulated overburden stresses between 0 and 12,800 psi. For this simulated downhole stress state, the undrilled rock sample was within the elastic response range and the confining pressures were found to have only a small or negligible effect on the penetration rate. Visual examination of the bottomhole pattern of the rocks after simulated downhole drilling, however, revealed ductile chipping of the Sandstone, but more brittle behavior in the Dolomite.

Sequence Stratigraphy of the Dakota Sandstone, Eastern San Juan Basin, New Mexico, and its Relationship to Reservoir Compartmentalization

Energy Technology Data Exchange (ETDEWEB)

Varney, Peter J.

2002-04-23

This research established the Dakota-outcrop sequence stratigraphy in part of the eastern San Juan Basin, New Mexico, and relates reservoir quality lithologies in depositional sequences to structure and reservoir compartmentalization in the South Lindrith Field area. The result was a predictive tool that will help guide further exploration and development.

Mass-production of Cambro-Ordovician quartz-rich sandstone as a consequence of chemical weathering of Pan-African terranes: Environmental implications [rapid communication

Science.gov (United States)

Avigad, D.; Sandler, A.; Kolodner, K.; Stern, R. J.; McWilliams, M.; Miller, N.; Beyth, M.

2005-12-01

A vast sheet of mature quartz sand blanketed north Africa and Arabia from the Atlantic coast to the Persian Gulf in Cambro-Ordovician times. U-Pb geochronology of a representative section of Cambrian sandstone in southern Israel shows that these sediments are dominated by 550-650 Ma detrital zircons derived from Neoproterozoic Pan-African basement. The short time lag between magmatic consolidation of a Pan-African source and deposition of its erosional products indicates that, despite their significant mineralogical maturity, the voluminous quartz-rich sandstones on the northern margin of Gondwana are essentially first-cycle sediments. Mass production of these voluminous first-cycle quartz-rich sandstones resulted from widespread chemical weathering of the Pan-African continental basement. We suggest that conditions favoring silicate weathering, particularly a warm and humid climate, low relief and low sedimentation rates prevailed over large tracts of Gondwana in the aftermath of the Pan-African orogeny. An unusually corrosive Cambro-Ordovician atmosphere and humid climate enhanced chemical weathering on the vegetation-free landscape. We infer that late Neoproterozoic-Cambro-Ordovician atmospheric pCO 2 rose as a consequence of widespread late Neoproterozoic volcanism, followed by an uptake of CO 2 by chemical weathering to produce the Cambro-Ordovician sandstone as a negative feedback.

The tide-influenced Pétervására sandstone, early Miocene, Northern Hungary : sedimentology, palaeogeography and basin development

NARCIS (Netherlands)

Sztanó, O.

1994-01-01

The objectives of this thesis are: - to determine the main sedimentary units, the dominant depositional processes, and to reconstruct the depositional environment of the Lower Miocene Petervasara Sandstone (Chapter 3), - to show the pattern of sediment dispersal in connection with the potential

The Comparison of Detrital Zircon Ages to Point Count Provenance Analysis for the Pottsville Sandstone in the Northern Appalachian Foreland Basin Venango County, Pennsylvania

Science.gov (United States)

Loveday, S.; Harris, D. B.; Schiappa, T.; Pecha, M.

2017-12-01

The specific sources of sediments deposited in the Appalachian basin prior to and immediately following the Alleghenian orogeny has long been a topic of debate. Recent advances in U-Pb dating of detrital zircons have greatly helped to determine some of the sources of these sediments. For this study, sandstone samples were collected from the Pottsville Formation in the northern Appalachian Foreland Basin, Venango County, Pennsylvania to provide supplementary data for previous work that sought to describe the provenance of the same sediments by point counts of thin sections of the same units. Results of this previous work established that the provenance for these units was transitional recycled orogenic, including multiple recycled sediments, and that a cratonic contribution was not able to be determined clearly. The previous results suggested that the paleoenvironment was a fluvial dominated delta prograding in the northern direction. However, no geochronologic data was found during this study to confirm this interpretation. We sought to verify these results by U-Pb analysis of detrital zircons. Samples were collected from the areas where the previous research took place. U-Pb ages were found from sample at the highest elevation and lowest elevation. In the first sample, sample 17SL01 (younger sample stratigraphically), the zircons yield U-Pb age range peaks at 442-468 ma and 1037-1081 ma. The probability density plot for this specific sample displays a complete age gap from 500 ma to 811 ma. In the second sample, sample 17SL03 (older rock stratigraphically), the zircons yield U-Pb ages range peaks of 424-616 ma and 975-1057 ma. This sample doesn't show any ages younger than 424 ma and it doesn't display the sample age gap as sample 17SL01 does. The ages of zircons are consistent with thin section point counting provenance results from previous research suggesting zircon transport from the northern direction.

Hydrological modelling in sandstone rocks watershed

Science.gov (United States)

Ponížilová, Iva; Unucka, Jan

2015-04-01

The contribution is focused on the modelling of surface and subsurface runoff in the Ploučnice basin. The used rainfall-runoff model is HEC-HMS comprising of the method of SCS CN curves and a recession method. The geological subsurface consisting of sandstone is characterised by reduced surface runoff and, on the contrary, it contributes to subsurface runoff. The aim of this paper is comparison of the rate of influence of sandstone on reducing surface runoff. The recession method for subsurface runoff was used to determine the subsurface runoff. The HEC-HMS model allows semi- and fully distributed approaches to schematisation of the watershed and rainfall situations. To determine the volume of runoff the method of SCS CN curves is used, which results depend on hydrological conditions of the soils. The rainfall-runoff model assuming selection of so-called methods of event of the SCS-CN type is used to determine the hydrograph and peak flow rate based on simulation of surface runoff in precipitation exceeding the infiltration capacity of the soil. The recession method is used to solve the baseflow (subsurface) runoff. The method is based on the separation of hydrograph to direct runoff and subsurface or baseflow runoff. The study area for the simulation of runoff using the method of SCS CN curves to determine the hydrological transformation is the Ploučnice basin. The Ploučnice is a hydrologically significant river in the northern part of the Czech Republic, it is a right tributary of the Elbe river with a total basin area of 1.194 km2. The average value of CN curves for the Ploučnice basin is 72. The geological structure of the Ploučnice basin is predominantly formed by Mesozoic sandstone. Despite significant initial loss of rainfall the basin response to the causal rainfall was demonstrated by a rapid rise of the surface runoff from the watershed and reached culmination flow. Basically, only surface runoff occures in the catchment during the initial phase of

High-resolution mapping of yield curve shape and evolution for high porosity sandstones

Science.gov (United States)

Bedford, J. D.; Faulkner, D.; Wheeler, J.; Leclere, H.

2017-12-01

The onset of permanent inelastic deformation for porous rock is typically defined by a yield curve plotted in P-Q space, where P is the effective mean stress and Q is the differential stress. Sandstones usually have broadly elliptical shaped yield curves, with the low pressure side of the ellipse associated with localized brittle faulting (dilation) and the high pressure side with distributed ductile deformation (compaction). However recent works have shown that these curves might not be perfectly elliptical and that significant evolution in shape occurs with continued deformation. We therefore use a novel stress-probing methodology to map in high-resolution the yield curve shape for Boise and Idaho Gray sandstones (36-38% porosity) and also investigate curve evolution with increasing deformation. The data reveal yield curves with a much flatter geometry than previously recorded for porous sandstone and that the compactive side of the curve is partly comprised of a near vertical limb. The yield curve evolution is found to be strongly dependent on the nature of inelastic strain. Samples that were compacted under a deviatoric load, with a component of inelastic shear strain, were found to have yield curves with peaks that are approximately 50% higher than similar porosity samples that were hydrostatically compacted (i.e. purely volumetric strain). The difference in yield curve evolution along the different loading paths is attributed to mechanical anisotropy that develops during deviatoric loading by the closure of preferentially orientated fractures. Increased shear strain also leads to the formation of a plateau at the peak of the yield curve as samples deform along the deviatoric loading path. These results have important implications for understanding how the strength of porous rock evolves along different stress paths, including during fluid extraction from hydrocarbon reservoirs where the stress state is rarely isotropic.

57Fe Mössbauer and X-ray characterisation of sandstones

International Nuclear Information System (INIS)

Mulaba-Bafubiandi, A. F.; Waanders, F. B.

2013-01-01

Sandstones from the Free State province in South Africa have been mined and processed mainly by small scale and artisanal miners in the rural areas. In the present investigation basic fire proof and water absorption tests, X-ray and γ-ray based characterisation techniques were used to study the sandstones. The collected samples were grouped according to their apparent colour in day light conditions and the elemental analysis showed the presence of a high amount of oxygen (>52%) and silicon (>38%) with Mn, Al, Fe and Ca as major elements in proportions related to the colour distribution of the various sandstones. The uniaxial compressive stress was found to be the highest (56 MPa) for the greyish sandstone and the lowest (8 MPa) for the white sandstone sample, also associated with the lowest (Al+Fe)/Si value of 0.082. The humidity test showed that the 6 % water absorption was lower than the recommended ASTM value of 8 %. The sandstone samples were also subjected to various high temperatures to simulate possible fire conditions and it was found that the non alteration of the mineral species might be one of the reasons why the sandstones are regarded as the most refractory amongst the building materials typically used. Mössbauer spectroscopy revealed that iron is present in all the sandstones, mainly as Fe 3 +  with the black sandstone showing an additional presence of 3 % Fe 2 +  indicating that a higher iron content coupled to higher silicon content, contributes to an increase in the uniaxial compressive strength.

Convolute laminations and load structures in turbidites as indicators of flow reflections and decelerations against bounding slopes. Examples from the Marnoso-arenacea Formation (northern Italy) and Annot Sandstones (south eastern France)

Science.gov (United States)

Tinterri, R.; Muzzi Magalhaes, P.; Tagliaferri, A.; Cunha, R. S.

2016-10-01

This work discusses the significance of particular types of soft-sediment deformations very common within turbidite deposits, namely convolute laminations and load structures. Detailed facies analyses of the foredeep turbidites in the Marnoso-arenacea Formation (northern Italy) and Annot Sandstones (south eastern France) show that these deformational structures tend to increase near morphological obstacles, concomitantly with contained-reflected beds. The lateral and vertical distribution of convolute laminae and load structures, as well as their geometry, has a well-defined depositional logic related to flow decelerations and reflections against bounding slopes. This evidence suggests an interaction between fine-grained sediment and the presence of morphologic relief, and impulsive and cyclic-wave loadings, which are produced by flow impacts or reflected bores and internal waves related to impinging bipartite turbidity currents.

The freshwater reservoir effect in radiocarbon dating

DEFF Research Database (Denmark)

Philippsen, Bente

case studies will show the degree of variability of the freshwater reservoir effect over short and long timescales. Radiocarbon dating of recent water samples, aquatic plants and animals, shows that age differences of up to 2000 years can occur within one river. In the Limfjord, freshwater influence......The freshwater reservoir effect can result in too high radiocarbon ages of samples from lakes and rivers, including the bones of people whose subsistence was based on freshwater fish, and pottery in which fish was cooked. In my talk, I will explain the causes and consequences of this effect. Two...... caused reservoir ages to vary between 250 and 700 years during the period 5400 BC - AD 700. Finally, I will discuss the implications of the freshwater reservoir effect for radiocarbon dating of Mesolithic pottery from inland sites of the Ertebølle culture in Northern Germany....

Northern reservoirs as sinks for Chernobyl cesium: sustained accumulation via introduced Mysis relicta in arctic char and brown trout

International Nuclear Information System (INIS)

Hammar, J.

1991-01-01

Fallout radiocesium from the Chernobyl accident caused extensive contamination in a region of previously well studied alpine lake ecosystems in northern Sweden. Levels of Cs-137 in the barren catchment basins reached 20-50 kBq/m 2 during 1986. The distribution and major transport mechanisms of radiocesium through the lake ecosystems have been studied during 1986-1990. Levels of Cs-137 in water, sediment, and different trophic levels of the food chains of Arctic char (Salvelinus alphinus) and brown trout (Salmo trutta) were monitored in a series of natural lakes and lake reservoirs, with or without the introduced new fish food organisms, Mysis relicta. The reservoirs were found to act as sinks for radiocesium with extensive accumulation recorded in water, sediment, invertebrates and salmonids. The introduced Mysis relicta were enhancing the transport of Cs-137 from zooplankton and settling particles to Arctic char and brown trout. The results suggest a successive change in transport of radiocesium from water via zooplankton to planktivorous fish during the early summer of 1986 to post-depositional mobilization via benthic organisms to benthic fish in successive years. (au) (32 refs.)

Petrography and geochemistry of Jurassic sandstones from the ...

Indian Academy of Sciences (India)

V Periasamy

On the basis of geochemical results, sandstones are classified into arkose, ..... Geochemical classification diagram of sandstone samples from the Jhuran Formation based on log(SiO2/Al2O3)– ..... 1993) showing single trend for the Jhuran.

Geological Carbon Sequestration Storage Resource Estimates for the Ordovician St. Peter Sandstone, Illinois and Michigan Basins, USA

Energy Technology Data Exchange (ETDEWEB)

Barnes, David; Ellett, Kevin; Leetaru, Hannes

2014-09-30

The Cambro-Ordovician strata of the Midwest of the United States is a primary target for potential geological storage of CO2 in deep saline formations. The objective of this project is to develop a comprehensive evaluation of the Cambro-Ordovician strata in the Illinois and Michigan Basins above the basal Mount Simon Sandstone since the Mount Simon is the subject of other investigations including a demonstration-scale injection at the Illinois Basin Decatur Project. The primary reservoir targets investigated in this study are the middle Ordovician St Peter Sandstone and the late Cambrian to early Ordovician Knox Group carbonates. The topic of this report is a regional-scale evaluation of the geologic storage resource potential of the St Peter Sandstone in both the Illinois and Michigan Basins. Multiple deterministic-based approaches were used in conjunction with the probabilistic-based storage efficiency factors published in the DOE methodology to estimate the carbon storage resource of the formation. Extensive data sets of core analyses and wireline logs were compiled to develop the necessary inputs for volumetric calculations. Results demonstrate how the range in uncertainty of storage resource estimates varies as a function of data availability and quality, and the underlying assumptions used in the different approaches. In the simplest approach, storage resource estimates were calculated from mapping the gross thickness of the formation and applying a single estimate of the effective mean porosity of the formation. Results from this approach led to storage resource estimates ranging from 3.3 to 35.1 Gt in the Michigan Basin, and 1.0 to 11.0 Gt in the Illinois Basin at the P10 and P90 probability level, respectively. The second approach involved consideration of the diagenetic history of the formation throughout the two basins and used depth-dependent functions of porosity to derive a more realistic spatially variable model of porosity rather than applying a

The streaming potential of liquid carbon dioxide in BreaSandstone

Energy Technology Data Exchange (ETDEWEB)

Moore, J.; Glaser, S.; Morrison, F.; Hoversten, G.M.

2004-10-01

We report here, for the first time, evolution of the streaming potential coupling coefficient as liquid carbon dioxide infiltrates Berea sandstone. Using 125 Omega-m tap water, the coupling coefficient determined before and after each CO2 flood of five samples averaged approximately -30 mV/0.1 MPa. After liquid CO2 passed through the specimens displacing all mobile pore water, trapped water remained and the coupling coefficient was approximately -3 mV/0.1 MPa. A bound water limit of the coupling coefficient for liquid CO2 flow was found using an air-dried sample to be -0.02 mV/0.1 MPa. For initially water-saturated samples, bulk resistivity varied during CO2 invasion from 330 Ohm-m, to 150 Ohm-m during CO2/water mixing, to a final value of 380 Ohm-m. Results suggest that trapped and bound water control electrical conduction and the electrokinetic response. Applications include monitoring CO2 injectate in subsurface reservoirs using the self potential method.

Petrofacies analysis - the petrophysical tool for geologic/engineering reservoir characterization

Energy Technology Data Exchange (ETDEWEB)

Watney, W.L.; Guy, W.J.; Gerlach, P.M. [Kansas Geological Survey, Lawrence, KS (United States)] [and others

1997-08-01

Petrofacies analysis is defined as the characterization and classification of pore types and fluid saturations as revealed by petrophysical measures of a reservoir. The word {open_quotes}petrofacies{close_quotes} makes an explicit link between petroleum engineers concerns with pore characteristics as arbiters of production performance, and the facies paradigm of geologists as a methodology for genetic understanding and prediction. In petrofacies analysis, the porosity and resistivity axes of the classical Pickett plot are used to map water saturation, bulk volume water, and estimated permeability, as well as capillary pressure information, where it is available. When data points are connected in order of depth within a reservoir, the characteristic patterns reflect reservoir rock character and its interplay with the hydrocarbon column. A third variable can be presented at each point on the crossplot by assigning a color scale that is based on other well logs, often gamma ray or photoelectric effect, or other derived variables. Contrasts between reservoir pore types and fluid saturations will be reflected in changing patterns on the crossplot and can help discriminate and characterize reservoir heterogeneity. Many hundreds of analyses of well logs facilitated by spreadsheet and object-oriented programming have provided the means to distinguish patterns typical of certain complex pore types for sandstones and carbonate reservoirs, occurrences of irreducible water saturation, and presence of transition zones. The result has been an improved means to evaluate potential production such as bypassed pay behind pipe and in old exploration holes, or to assess zonation and continuity of the reservoir. Petrofacies analysis is applied in this example to distinguishing flow units including discrimination of pore type as assessment of reservoir conformance and continuity. The analysis is facilitated through the use of color cross sections and cluster analysis.

Processing of reservoir data for diagenesis simulation; Traitement des donnees de reservoir en vue d`une simulation de la diagenese

Energy Technology Data Exchange (ETDEWEB)

Pelletier, I.

1997-12-18

Diagenetic minerals frequently damage reservoir permeability. A numerical model which couples chemical reactions and transport of dissolved elements can help to predict both location and magnitude of cementations. The present Ph.D. examines how can be applied such a modelling approach to a complex heterogeneous reservoir. Petrographical data from core samples are used as input data, or alternatively as controls for validating the modelling results. The measurements, acquired with dm-to-m spacing are too numerous to be integrated in a reactions-transport code. The usual up-scaling methods, called Homogenization, conserve only the fluid flow properties. A new method, called `Gathering` takes into account material transport balance. It is proposed in the first part of the dissertation. In the second part, an application of Gathering is done simulating illitization in the sub-arkosic sandstones of the Ness formation (Brent Group) in a North Sea field, Dunbar.. As a prerequisite, data accuracy is examined for a set of `routine measurements` (100 points counting on thin section, XR-diffractometry and gas porosity/permeability). (author) 60 refs.

Sensing, Measuring and Modelling the Mechanical Properties of Sandstone

Science.gov (United States)

Antony, S. J.; Olugbenga, A.; Ozerkan, N. G.

2018-02-01

We present a hybrid framework for simulating the strength and dilation characteristics of sandstone. Where possible, the grain-scale properties of sandstone are evaluated experimentally in detail. Also, using photo-stress analysis, we sense the deviator stress (/strain) distribution at the micro-scale and its components along the orthogonal directions on the surface of a V-notch sandstone sample under mechanical loading. Based on this measurement and applying a grain-scale model, the optical anisotropy index K 0 is inferred at the grain scale. This correlated well with the grain contact stiffness ratio K evaluated using ultrasound sensors independently. Thereafter, in addition to other experimentally characterised structural and grain-scale properties of sandstone, K is fed as an input into the discrete element modelling of fracture strength and dilation of the sandstone samples. Physical bulk-scale experiments are also conducted to evaluate the load-displacement relation, dilation and bulk fracture strength characteristics of sandstone samples under compression and shear. A good level of agreement is obtained between the results of the simulations and experiments. The current generic framework could be applied to understand the internal and bulk mechanical properties of such complex opaque and heterogeneous materials more realistically in future.

Eutrophication study at the Panjiakou-Daheiting Reservoir system, northern Hebei Province, People's Republic of China: Chlorophyll-a model and sources of phosphorus and nitrogen

Science.gov (United States)

Domagalski, Joseph L.; Lin, Chao; Luo, Yang; Kang, Jie; Wang, Shaoming; Brown, Larry R.; Munn, Mark D.

2007-01-01

Concentrations, loads, and sources of nitrate and total phosphorus were investigated at the Panjiakou and Daheiting Reservoir system in northern Hebei Province, People's Republic of China. The Luan He River is the primary source of water to these reservoirs, and the upstream watershed has a mix of land uses including agriculture, forest, and one large urban center. The reservoirs have a primary use for storage of drinking water and partially supply Tianjin City with its annual needs. Secondary uses include flood control and aqua culture (fish cages). The response of the reservoir system from phosphorus input, with respect to chlorophyll-a production from algae, was fitted to a model of normalized phosphorus loading that regresses the average summer-time chlorophyll-a concentration to the average annual phosphorus concentration of the reservoir. Comparison of the normalized phosphorus loading and chlorophyll-a response of this system to other reservoirs throughout the world indicate a level of eutrophication that will require up to an approximate 5–10-fold decrease in annual phosphorus load to bring the system to a more acceptable level of algal productivity. Isotopes of nitrogen and oxygen in dissolved nitrate were measured from the headwater streams and at various locations along the major rivers that provide the majority of water to these reservoirs. Those isotopic measurements indicate that the sources of nitrate change from natural background in the rivers to animal manure and septic waste upstream of the reservoir. Although the isotopic measurements suggest that animal and septic wastes are a primary source of nutrients, measurements of the molar ratio of nitrogen to phosphorus are more indicative of row-cropping practices. Options for reduction of nutrient loads include changing the management practices of the aqua culture, installation of new sewage treatment systems in the large urbanized area of the upper watershed, and agricultural management practices

Transport of silver nanoparticles in single fractured sandstone

Science.gov (United States)

Neukum, Christoph

2018-02-01

Silver nanoparticles (Ag-NP) are used in various consumer products and are one of the most prevalent metallic nanoparticle in commodities and are released into the environment. Transport behavior of Ag-NP in groundwater is one important aspect for the assessment of environmental impact and protection of drinking water resources in particular. Ag-NP transport processes in saturated single-fractured sandstones using triaxial flow cell experiments with different kind of sandstones is investigated. Ag-NP concentration and size are analyzed using flow field-flow fractionation and coupled SEM-EDX analysis. Results indicate that Ag-NP are more mobile and show generally lower attachment on rock surface compared to experiments in undisturbed sandstone matrix and partially fractured sandstones. Ag-NP transport is controlled by the characteristics of matrix porosity, time depending blocking of attachment sites and solute chemistry. Where Ag-NP attachment occur, it is heterogeneously distributed on the fracture surface.

Drag reduction in reservoir rock surface: Hydrophobic modification by SiO_2 nanofluids

International Nuclear Information System (INIS)

Yan, Yong-Li; Cui, Ming-Yue; Jiang, Wei-Dong; He, An-Le; Liang, Chong

2017-01-01

Graphical abstract: The micro-nanoscale hierarchical structures at the sandstone core surface are constructed by adsorption of the modified silica nanoparticles, which leads to the effect of drag reduction to improve the low injection rate in ultra-low permeability reservoirs. - Highlights: • A micro-nanoscale hierarchical structure is formed at the reservoir rock surface. • An inversion has happened from hydrophilic into hydrophobic modified by nanofluids. • The effect of drag reduction to improve the low injection rate is realized. • The mechanism of drag reduction induced from the modified core surface was unclosed. - Abstract: Based on the adsorption behavior of modified silica nanoparticles in the sandstone core surface, the hydrophobic surface was constructed, which consists of micro-nanoscale hierarchical structure. This modified core surface presents a property of drag reduction and meets the challenge of high injection pressure and low injection rate in low or ultra-low permeability reservoir. The modification effects on the surface of silica nanoparticles and reservoir cores, mainly concerning hydrophobicity and fine structure, were determined by measurements of contact angle and scanning electron microscopy. Experimental results indicate that after successful modification, the contact angle of silica nanoparticles varies from 19.5° to 141.7°, exhibiting remarkable hydrophobic properties. These modified hydrophobic silica nanoparticles display a good adsorption behavior at the core surface to form micro-nanobinary structure. As for the wettability of these modified core surfaces, a reversal has happened from hydrophilic into hydrophobic and its contact angle increases from 59.1° to 105.9°. The core displacement experiments show that the relative permeability for water has significantly increased by an average of 40.3% via core surface modification, with the effects of reducing injection pressure and improving injection performance of water

Fracture-related fluid flow in sandstone reservoirs - Insights from outcrop analogues of South-eastern Utah

NARCIS (Netherlands)

Ogata, K.; Senger, K.; Braathen, A.; Tveranger, J.; Petrie, E.; Evans, J.P.

2012-01-01

Fault- And fold-related fractures influence the fluid circulation in the subsurface, thus being of high importance for CO2 storage site assessment, especially in terms of reservoir connectivity and leakage. In this context, discrete regions of concentrated sub-parallel fracturing known as fracture

Detrital zircon provenance of the Hartselle Sandstone Unit, Southeastern USA: Insights into sediment source, paleogeography, and setting

Science.gov (United States)

Harthy, M. A.; Gifford, J.

2017-12-01

The Hartselle sandstone is an excellent example of an Oil sand, a resource rich in bitumen. The unit is a light-colored thick-bedded to massive quartzose sandstone, that is widespread across an area from Georgia in the east to Mississippi in the west, and south from Alabama to Kentucky as a northern border. Formation thickness ranges from 0 to more than 150 feet. The unit has been stratigraphically dated to the Middle-Upper Mississippian age. One hypothesis suggests that the sandstone unit formed from the geological remains of barrier islands located in the ocean between Gondwana and Laurentia. The Hartselle is thought to have formed by the movement waves and currents along the shoreline, which carried sand and concentrated it into a set of northwest to southeast trending barrier islands. Transgression-regression events shifted the islands back and forth in relation to the position of the shoreline, leading to the large areal extent of the unit. However, the current data are not enough to explain the geographical position of the Hartselle sandstone unit as it is not running parallel to the ancient shoreline. Another mystery is the source of the sand, some believing the source was from the south (Gondwana) and others that erosion was from the north (Laurentia). Detrital zircon provenance analysis will address the uncertainty in sediment source. We will compare zircon U-Pb age spectra to possible Laurentian and Gondwanan source areas to discriminate between these possibilities. In addition, the age of the youngest detrital zircon population will provide additional constraints on the maximum age of deposition for the unit. These detrital ages will also help us to understand the tectonic setting at the time of Hartselle deposition. Lastly, we aim to explain the widespread nature of the unit and the processes involved in the formation of the Hartselle sandstone. When taken together, these interpretations will illuminate the age, depositional and tectonic setting of a

INAA and petrological study of sandstones from the Angkor monuments

International Nuclear Information System (INIS)

Kucera, J.; Kranda, K.; Soukal, L.; Novak, J.K.; Lang, M.; Poncar, J.; Krausova, I.; Cunin, O.

2008-01-01

We determined 35 major, minor and trace elements in sandstone samples taken from building blocks of 19 Angkor temples and from an old and a new quarry using INAA. We also characterized the sandstone samples with conventional microscopy and electron microprobe analysis. Using cluster analysis, we found no straightforward correlation between the chemical/petrological properties of the sandstones and a presumed period of individual temples construction. The poor correlation may result either from the inherent inhomogeneity of sandstone or just reflect the diversity of quarries that supplied building blocks for the construction of any particular temple. (author)

The Baltic Basin: structure, properties of reservoir rocks, and capacity for geological storage of CO2

Directory of Open Access Journals (Sweden)

Vaher, Rein

2009-12-01

Full Text Available Baltic countries are located in the limits of the Baltic sedimentary basin, a 700 km long and 500 km wide synclinal structure. The axis of the syneclise plunges to the southwest. In Poland the Precambrian basement occurs at a depth of 5 km. The Baltic Basin includes the Neoproterozoic Ediacaran (Vendian at the base and all Phanerozoic systems. Two aquifers, the lower Devonian and Cambrian reservoirs, meet the basic requirements for CO2 storage. The porosity and permeability of sandstone decrease with depth. The average porosity of Cambrian sandstone at depths of 80–800, 800–1800, and 1800–2300 m is 18.6, 14.2, and 5.5%, respectively. The average permeability is, respectively, 311, 251, and 12 mD. Devonian sandstone has an average porosity of 26% and permeability in the range of 0.5–2 D. Prospective Cambrian structural traps occur only in Latvia. The 16 largest ones have CO2 storage capacity in the range of 2–74 Mt, with total capacity exceeding 400 Mt. The structural trapping is not an option for Lithuania as the uplifts there are too small. Another option is utilization of CO2 for enhanced oil recovery (EOR. The estimated total EOR net volume of CO2 (part of CO2 remaining in the formation in Lithuania is 5.6 Mt. Solubility and mineral trapping are a long-term option. The calculated total solubility trapping capacity of the Cambrian reservoir is as high as 11 Gt of CO2 within the area of the supercritical state of carbon dioxide.

Evaluating the Implications of Climate Phenomenon Indices in Supporting Reservoir Operation Using the Artificial Neural Network and Decision-Tree Methods: A Case Study on Trinity Lake in Northern California

Science.gov (United States)

Yang, T.; Akbari Asanjan, A.; Gao, X.; Sorooshian, S.

2016-12-01

Reservoirs are fundamental human-built infrastructures that collect, store, and deliver fresh surface water in a timely manner for all kinds of purposes, including residential and industrial water supply, flood control, hydropower, and irrigation, etc. Efficient reservoir operation requires that policy makers and operators understand how reservoir inflows, available storage, and discharges are changing under different climatic conditions. Over the last decade, the uses of Artificial Intelligence and Data Mining (AI & DM) techniques in assisting reservoir management and seasonal forecasts have been increasing. Therefore, in this study, two distinct AI & DM methods, Artificial Neural Network (ANN) and Random Forest (RF), are employed and compared with respect to their capabilities of predicting monthly reservoir inflow, managing storage, and scheduling reservoir releases. A case study on Trinity Lake in northern California is conducted using long-term (over 50 years) reservoir operation records and 17 known climate phenomenon indices, i.e. PDO and ENSO, etc., as predictors. Results show that (1) both ANN and RF are capable of providing reasonable monthly reservoir storage, inflow, and outflow prediction with satisfactory statistics, and (2) climate phenomenon indices are useful in assisting monthly or seasonal forecasts of reservoir inflow and outflow. It is also found that reservoir storage has a consistent high autocorrelation effect, while inflow and outflow are more likely to be influenced by climate conditions. Using a Gini diversity index, RF method identifies that the reservoir discharges are associated with Southern Oscillation Index (SOI) and reservoir inflows are influenced by multiple climate phenomenon indices during different seasons. Furthermore, results also show that, during the winter season, reservoir discharges are controlled by the storage level for flood-control purposes, while, during the summer season, the flood-control operation is not as

INTRODUCTION Sandstone beds within Auchi locality are the ...

African Journals Online (AJOL)

The major framework composition is Q F L which classifies the sandstone as Quartz ... The grains are texturally immature as depicted by their subangular edges but mineralogically ..... Fig 6 : Vertical Section of Bioturbated Sandstone Lithofacies Showing Trace Fossils ..... on Water Quality and Planktonic Production in an.

FEASIBILITY STUDY OF SEDIMENT FLUSHING FROM MOSUL RESERVOIR, IRAQ

Directory of Open Access Journals (Sweden)

Thair Mahmood Al-Taiee

2015-02-01

Full Text Available The Feasibility of sediment flushing  from Mosul reservoir located northern iraq was conducted. Many up to date world criteria and indices for checking the efficiency of sediment flushing from reservoir which have been got through analyzing large amount of  data from many flushed reservoirs  in the world which were depended tested and applied in the present case study (Mosul Reservoir. These criteria and indices depend mainly on the hydrological , hydraulic and  topographical properties of the reservoirs in-addition to the operation plan of the reservoirs. They gave a good indication for checking the efficiency of the sediment flushing  process in the reservoirs. It was concluded that approximately the main criteria for the successful flushing sediment was  verified  in  Mosul  reservoir  such as  Sediment Balance Ratio   (SBR and the Long Term Capacity Ratio (LTCR,the shape factor  of reservoir (W/L and the hydraulic condition such as the percentage of (Qf/Qin and (Vf/Vin. This gave an indication that the processes of flushing sediment in Mosul reservoir is probably feasible and may be applied  in the future to maintain the water storage in the reservoir.

Sequence Stratigraphy of the Dakota Sandstone, Eastern San Juan Basin, New Mexico, and its Relationship to Reservoir Compartmentalization; FINAL

International Nuclear Information System (INIS)

Varney, Peter J.

2002-01-01

This research established the Dakota-outcrop sequence stratigraphy in part of the eastern San Juan Basin, New Mexico, and relates reservoir quality lithologies in depositional sequences to structure and reservoir compartmentalization in the South Lindrith Field area. The result was a predictive tool that will help guide further exploration and development

Turkana Grits - a Cretaceous braided alluvial system in northern Kenya

Energy Technology Data Exchange (ETDEWEB)

Handford, C.R.

1987-05-01

Rather spotty but excellent exposures of the Cretaceous-age Turkana Grits occur near the western shore of Lake Turkana, northern Kenya. These very coarse to pebbly arkosic sandstones and sandy conglomerates were derived from and rest unconformably upon Precambrian metamorphic basement; they are overlain by late Tertiary basaltic flows that comprise much of the volcanics in the East African Rift Zone. The formation ranges up to 2000 ft thick in the Laburr Range. Several outcrops contain sauropod, crocodile, and tortoise remains as well as abundant trunks of petrified wood (Dryoxylon). Five major facies make up the Turkana Grits and record a major episode of continental fluvial deposition in basins flanked by Precambrian basement. Facies 1 is crudely stratified, cobble and boulder conglomerate (clast-supported); Facies 2 is crudely stratified pebble-cobble conglomerate and pebbly sandstone; Facies 3 is trough cross-bedded, very coarse sandstones containing fossils wood and vertebrate remains; Facies 4 is crudely stratified to massive sandstones with ironstone nodules; and Facies 5 is red, purple, and gray mudstone and mud shale with carbonate nodules. Facies 1 through 3 record deposition in proximal to medial braided-stream channel, longitudinal bar and dune complexes. Facies 4 is a lowland, hydromorphic paleosol, and Facies 5 represents overbank and abandoned channel-fill sedimentation in an alluvial plain.

Assessment of managed aquifer recharge at Sand Hollow Reservoir, Washington County, Utah, updated to conditions through 2014

Science.gov (United States)

Marston, Thomas M.; Heilweil, Victor M.

2016-09-08

Sand Hollow Reservoir in Washington County, Utah, was completed in March 2002 and is operated primarily for managed aquifer recharge by the Washington County Water Conservancy District. From 2002 through 2014, diversions of about 216,000 acre-feet from the Virgin River to Sand Hollow Reservoir have allowed the reservoir to remain nearly full since 2006. Groundwater levels in monitoring wells near the reservoir rose through 2006 and have fluctuated more recently because of variations in reservoir stage and nearby pumping from production wells. Between 2004 and 2014, about 29,000 acre-feet of groundwater was withdrawn by these wells for municipal supply. In addition, about 31,000 acre-feet of shallow seepage was captured by French drains adjacent to the North and West Dams and used for municipal supply, irrigation, or returned to the reservoir. From 2002 through 2014, about 127,000 acre-feet of water seeped beneath the reservoir to recharge the underlying Navajo Sandstone aquifer.Water quality continued to be monitored at various wells in Sand Hollow during 2013–14 to evaluate the timing and location of reservoir recharge as it moved through the aquifer. Changing geochemical conditions at monitoring wells WD 4 and WD 12 indicate rising groundwater levels and mobilization of vadose-zone salts, which could be a precursor to the arrival of reservoir recharge.

Assessment of managed aquifer recharge from Sand Hollow Reservoir, Washington County, Utah, updated to conditions in 2010

Science.gov (United States)

Heilweil, Victor M.; Marston, Thomas M.

2011-01-01

Sand Hollow Reservoir in Washington County, Utah, was completed in March 2002 and is operated primarily for managed aquifer recharge by the Washington County Water Conservancy District. From 2002 through 2009, total surface-water diversions of about 154,000 acre-feet to Sand Hollow Reservoir have allowed it to remain nearly full since 2006. Groundwater levels in monitoring wells near the reservoir rose through 2006 and have fluctuated more recently because of variations in reservoir water-level altitude and nearby pumping from production wells. Between 2004 and 2009, a total of about 13,000 acre-feet of groundwater has been withdrawn by these wells for municipal supply. In addition, a total of about 14,000 acre-feet of shallow seepage was captured by French drains adjacent to the North and West Dams and used for municipal supply, irrigation, or returned to the reservoir.From 2002 through 2009, about 86,000 acre-feet of water seeped beneath the reservoir to recharge the underlying Navajo Sandstone aquifer. Water-quality sampling was conducted at various monitoring wells in Sand Hollow to evaluate the timing and location of reservoir recharge moving through the aquifer. Tracers of reservoir recharge include major and minor dissolved inorganic ions, tritium, dissolved organic carbon, chlorofluorocarbons, sulfur hexafluoride, and noble gases. By 2010, this recharge arrived at monitoring wells within about 1,000 feet of the reservoir.

Current results of an arachnological survey of some sandstone rock sites in Bohemia (so-called "rock cities"

Directory of Open Access Journals (Sweden)

Růžička, Vlastimil

1992-07-01

Full Text Available The spider fauna of the Adrspach-Teplice rockswas investigated. Some records on spider fauna of other nine sandstone rock areas are included. The phenomenon of "rock cities" manifests itself in three aspects: (1 In the bottom parts are microclimatically cold spaces, frequently hosting northern ot mountain species of invertebrates, which here have an azonal occurence. (2 the sun exposed tops of rocks can host thermophilous species. (3 Some species are limited to the surface of rocks and boulders. These are referred to as lithophilous or lithobiont species.

Contribution to the tectonic characterization of fractured reservoirs, I: photo-elasticimetric modelling of the stress perturbations near faults and the associated fracture network: application to oil reserves, II mechanisms for the 3D joint organization in a natural reservoir analogue (flat-lying Devonian Old Red Sandstones of Caitness in North Scotland); Contribution a la caracterisation tectonique des reservoirs fractures, I: modelisation photoelecticimetrique des perturbations de contrainte au voisinage des failles et de la fracturation associee: application petroliere, II: mecanismes de developpement en 3D des diaclases dans un analogue de reservoir, le Devonien tabulaire du caithness (Ecosse)

Energy Technology Data Exchange (ETDEWEB)

Auzias, V

1995-10-27

In order to understand joint network organisation in oil reservoirs, as a first step we have adapted to technique (the photo-elasticimetry) to study stress fields in 2D. This method allows to determine the principal stress trajectories near faults, as well as the associated joint network organisation. Natural joint networks perturbed near faults are modeled and the parameters that control stress perturbation are proposed. With the aim of extrapolating joint data from a well to the entire reservoir our modelling is based on both 3 D seismic data and local joint data. The second part of our research was dedicated to studying joint propagation mechanisms in a natural reservoir analogue (flat-lying Devonian Old Red Sandstones of Caitness in North Scotland). Several exposure observation at different scales and in 3D (horizontal and cliff sections) allow to reconstitute the fracturing geometry from centimeter to kilometer scale and to link these to the regional tectonic history. This study shows that it is possible to differentiate three types of joints major joints, `classic` joints and micro-joints, each with different vertical persistence. New concepts on the 3D joint organisation have been deduced from field quantitative data, which can be applied to reservoir fracture modeling. In particular the non-coexistence phenomenon in a single bed of two regional joint sets with close strikes. Some joint development mechanisms are discussed: interaction between joints and sedimentary interfaces, joint distribution near faults, origin of en echelon arrays associated with joints. (author) 142 refs.

Formation conditions and prospecting criteria for sandstone uranium deposit of interlayer oxidation type

International Nuclear Information System (INIS)

Huang Shijie

1994-01-01

This paper comprehensively analyses the geotectonic setting and favourable conditions, such as structure of the basin, sedimentary facies and paleogeography, geomorphology and climate, hydrodynamics and hydrogeochemistry, the development of interlayered oxidation etc, necessary for the formation of sandstone uranium deposit of interlayered oxidation type. The following prospecting criteria is proposed, namely: abundant uranium source, arid climate, stable big basin, flat-lying sandstone bed, big alluvial fan, little change in sedimentary facies, intercalation of sandstone and mudstone beds, shallow burying of sandstone bed, well-aquiferous sandstone bed, high permeability of sandstone bed, development of interlayered oxidation, and high content of reductant in sandstone. In addition, the 6 in 1 hydrogenic genetic model is proposed

Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

International Nuclear Information System (INIS)

Stear, W.M.

1980-01-01

Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times

Channel sandstone and bar morphology of the Beaufort group uranium district near Beaufort West

Energy Technology Data Exchange (ETDEWEB)

Stear, W M

1980-01-01

Sheet-like and lenticular sandstone bodies in the Lower Beaufort Group (Adelaide Subgroup) uranium district occur in megacyclic repetition as superimposed systems of ephemeral fluvial channels that display characteristics of complex lateral and vertical accretion. Channel sandstone bodies are defined on morphological grounds into two types. Sheet sandstone bodies are the commonest type and comprise the bulk of sandstone packages in arenaceous zones of megacycles. Composite sandstone sheets result from multilateral coalescence of individual sandstone bodies. Isolated lenticular sandstone units in argillaceous zones of megacycles comprise sheet and ribbon sandstone types. Multi-storeying is a prominent feature of most channel sandstone bodies and often results in local sandstone thickening. Bedforms relate to the formation of compound bars and record periods of dynamic accretion and erosion. Rarely preserved palaeosurfaces vividly illustrate the fluctuating hydrodynamic conditions that typified ephemeral fluvial sedimentation in a semi-arid environment during Lower Beaufort times.

Fracture properties from tight reservoir outcrop analogues with application to geothermal exploration

Science.gov (United States)

Philipp, Sonja L.; Reyer, Dorothea; Afsar, Filiz; Bauer, Johanna F.; Meier, Silke; Reinecker, John

2015-04-01

In geothermal reservoirs, similar to other tight reservoirs, fluid flow may be intensely affected by fracture systems, in particular those associated with fault zones. When active (slipping) the fault core, that is, the inner part of a fault zone, which commonly consists of breccia or gouge, can suddenly develop high permeability. Fault cores of inactive fault zones, however, may have low permeabilities and even act as flow barriers. In the outer part of a fault zone, the damage zone, permeability depends mainly on the fracture properties, that is, the geometry (orientation, aperture, density, connectivity, etc.) of the fault-associated fracture system. Mineral vein networks in damage zones of deeply eroded fault zones in palaeogeothermal fields demonstrate their permeability. In geothermal exploration, particularly for hydrothermal reservoirs, the orientation of fault zones in relation to the current stress field as well as their internal structure, in particular the properties of the associated fracture system, must be known as accurately as possible for wellpath planning and reservoir engineering. Here we present results of detailed field studies and numerical models of fault zones and associated fracture systems in palaeogeo¬thermal fields and host rocks for geothermal reservoirs from various stratigraphies, lithologies and tectonic settings: (1) 74 fault zones in three coastal sections of Upper Triassic and Lower Jurassic age (mudstones and limestone-marl alternations) in the Bristol Channel Basin, UK. (2) 58 fault zones in 22 outcrops from Upper Carboniferous to Upper Cretaceous in the Northwest German Basin (siliciclastic, carbonate and volcanic rocks); and (3) 16 fault zones in 9 outcrops in Lower Permian to Middle Triassic (mainly sandstone and limestone) in the Upper Rhine Graben shoulders. Whereas (1) represent palaeogeothermal fields with mineral veins, (2) and (3) are outcrop analogues of reservoir horizons from geothermal exploration. In the study

Improved Oil Recovery in Fluvial Dominated Deltaic Reservoirs of Kansas - Near-Term

International Nuclear Information System (INIS)

Green, Don W.; McCune, A.D.; Michnick, M.; Reynolds, R.; Walton, A.; Watney, L.; Willhite, G. Paul

1999-01-01

The objective of this project is to address waterflood problems of the type found in Morrow sandstone reservoirs in southwestern Kansas and in Cherokee Group reservoirs in southeastern Kansas. Two demonstration sites operated by different independent oil operators are involved in this project. The Stewart Field is located in Finney County, Kansas and is operated by PetroSantander, Inc. Te Nelson Lease is located in Allen County, Kansas, in the N.E. Savonburg Field and is operated by James E. Russell Petroleum, Inc. General topics to be addressed are (1) reservoir management and performance evaluation, (2) waterflood optimization, and (3) the demonstration of recovery processes involving off-the-shelf technologies which can be used to enhance waterflood recovery, increase reserves, and reduce the abandonment rate of these reservoir types. In the Stewart Project, the reservoir management portion of the project conducted during Budget Period 1 involved performance evaluation. This included (1) reservoir characterization and the development of a reservoir database, (2) volumetric analysis to evaluate production performance, (3) reservoir modeling, (4) laboratory work, (5) identification of operational problems, (6) identification of unrecovered mobile oil and estimation of recovery factors, and (7) Identification of the most efficient and economical recovery process. To accomplish these objectives the initial budget period was subdivided into three major tasks. The tasks were (1) geological and engineering analysis, (2) laboratory testing, and (3) unitization. Due to the presence of different operators within the field, it was necessary to unitize the field in order to demonstrate a field-wide improved recovery process. This work was completed and the project moved into Budget Period 2

Sedimentology, Sequence Stratigraphy and Reservoir Characterization of Samana Suk Formation Exposed in Namal Gorge Section, Salt Range, Mianwali, Punjab, Pakistan

Directory of Open Access Journals (Sweden)

Muhammad Hayat

2016-06-01

Full Text Available Samana Suk Formation of Bathonian-callovain age, exposed in Nammal Gorge Salt Range, has been studied for microfacies and sequence stratigraphic investigation. The formation is mainly composed of limestone, with minor beds of sandstone and marl. The limestone is grey, yellowish and purple in color. Limestone is fine grained, thin to medium bedded and inter-bedded with algal laminations. The sandstone is light yellowish brown, brick red in color, calcareous and quartzose. Within Samana Suk Formation one 2ndorder sequence and two 3rdorder sequences have been identified. Their regional correlation through fine-tuned dating helped to develop basin fill model and to understand facies dynamics. A facie belt comprising a wide belt of carbonate facies characterized by Peloidal Packstone microfacies represents inner ramp setting and Pelletal/ Peloidal Wackstone, Mud-Wackstone and Mudstone microfacies represent the low energy lagoonal environment. The sandstone lithofacies represents high energy beach environment which indicates aggrading to pro-grading pattern. The porosity analysis has been done on different samples of limestone and sandstone. For the porosity analysis the Image J software is used. In limestone the porosity ranges up to 6% while in sandstone the porosity ranging up to 18%. From the field and porosity analysis it is concluded that Samana Suk Formation in study area is good reservoir.

Effect of retrograde gas condensate in low permeability natural gas reservoir; Efeito da condensacao retrograda em reservatorios de gas natural com baixa permeabilidade

Energy Technology Data Exchange (ETDEWEB)

Chang, Paulo Lee K.C. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica; Ligero, Eliana L.; Schiozer, Denis J. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Engenharia de Petroleo

2008-07-01

Most of Brazilian gas fields are low-permeability or tight sandstone reservoirs and some of them should be gas condensate reservoir. In this type of natural gas reservoir, part of the gaseous hydrocarbon mixture is condensate and the liquid hydrocarbon accumulates near the well bore that causes the loss of productivity. The liquid hydrocarbon formation inside the reservoir should be well understood such as the knowledge of the variables that causes the condensate formation and its importance in the natural gas production. This work had as goal to better understanding the effect of condensate accumulation near a producer well. The influence of the porosity and the absolute permeability in the gas production was studied in three distinct gas reservoirs: a dry gas reservoir and two gas condensate reservoirs. The refinement of the simulation grid near the producer well was also investigated. The choice of simulation model was shown to be very important in the simulation of gas condensate reservoirs. The porosity was the little relevance in the gas production and in the liquid hydrocarbon formation; otherwise the permeability was very relevant. (author)

Application of advanced reservoir characterization, simulation, and production optimization strategies to maximize recovery in slope and basin clastic reservoirs, West Texas (Delaware Basin). Quarterly report, October 1 - December 31, 1996

Energy Technology Data Exchange (ETDEWEB)

Dutton, S.P.

1997-01-01

The objective of this project is to demonstrate that detailed reservoir characterization of slope and basin clastic reservoirs in sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost effective way to recover a higher percentage of the original oil in place through strategic placement of infill wells and geologically based field development. Project objectives are divided into two major phases. The objectives of the reservoir characterization phase of the project are to provide a detailed understanding of the architecture and heterogeneity of two fields, the Ford Geraldine unit and Ford West field, which produce from the Bell Canyon and Cherry Canyon Formations, respectively, of the Delaware Mountain Group and to compare Bell Canyon and Cherry Canyon reservoirs. Reservoir characterization will utilize 3-D seismic data, high-resolution sequence stratigraphy, subsurface field studies, outcrop characterization, and other techniques. Once the reservoir-characterization study of both fields is completed, a pilot area of approximately 1 mi{sup 2} in one of the fields will be chosen for reservoir simulation. The objectives of the implementation phase of the project are to (1) apply the knowledge gained from reservoir characterization and simulation studies to increase recovery from the pilot area, (2) demonstrate that economically significant unrecovered oil remains in geologically resolvable untapped compartments, and (3) test the accuracy of reservoir characterization and flow simulation as predictive tools in resource preservation of mature fields. A geologically designed, enhanced-recovery program (CO{sub 2} flood, waterflood, or polymer flood) and well-completion program will be developed, and one to three infill wells will be drilled and cored. Technical progress is summarized for: geophysical characterization; reservoir characterization; outcrop characterization; and recovery technology identification and analysis.

Drag reduction in reservoir rock surface: Hydrophobic modification by SiO{sub 2} nanofluids

Energy Technology Data Exchange (ETDEWEB)

Yan, Yong-Li, E-mail: yylhill@163.com [College of Chemistry & Chemical Engineering, Xi’an Shiyou University, Xi’an 710065 (China); Cui, Ming-Yue; Jiang, Wei-Dong; He, An-Le; Liang, Chong [Langfang Branch of Research Institute of Petroleum Exploration & Development, Langfang 065007 (China)

2017-02-28

Graphical abstract: The micro-nanoscale hierarchical structures at the sandstone core surface are constructed by adsorption of the modified silica nanoparticles, which leads to the effect of drag reduction to improve the low injection rate in ultra-low permeability reservoirs. - Highlights: • A micro-nanoscale hierarchical structure is formed at the reservoir rock surface. • An inversion has happened from hydrophilic into hydrophobic modified by nanofluids. • The effect of drag reduction to improve the low injection rate is realized. • The mechanism of drag reduction induced from the modified core surface was unclosed. - Abstract: Based on the adsorption behavior of modified silica nanoparticles in the sandstone core surface, the hydrophobic surface was constructed, which consists of micro-nanoscale hierarchical structure. This modified core surface presents a property of drag reduction and meets the challenge of high injection pressure and low injection rate in low or ultra-low permeability reservoir. The modification effects on the surface of silica nanoparticles and reservoir cores, mainly concerning hydrophobicity and fine structure, were determined by measurements of contact angle and scanning electron microscopy. Experimental results indicate that after successful modification, the contact angle of silica nanoparticles varies from 19.5° to 141.7°, exhibiting remarkable hydrophobic properties. These modified hydrophobic silica nanoparticles display a good adsorption behavior at the core surface to form micro-nanobinary structure. As for the wettability of these modified core surfaces, a reversal has happened from hydrophilic into hydrophobic and its contact angle increases from 59.1° to 105.9°. The core displacement experiments show that the relative permeability for water has significantly increased by an average of 40.3% via core surface modification, with the effects of reducing injection pressure and improving injection performance of water

Distribution characteristics of Shihongtan uranium deposits calcareous sandstone and discussion on their genesis

International Nuclear Information System (INIS)

Zhu Huanqiao; Jia Heng; Xu Gaozhong; Li Zhanyou

2007-12-01

It is considered that the calcareous sandstone appear at layer along of a bunch of pear lens on and off, localled near up and down surface of sandbody or washed surface, has sandstone of more macro-grain and more gradation through statistics and analysis of calcareous sandstone in goal layer in Shihongtan uranium deposits. The calcareous sandstone accumulation thickness chorogram demonstrated that the calcareous sandstone centralized distribution in the ore body growth area, thus it can be seen, in the oxidation reduction intermediate belt the calcareous sandstone forms with the uranium mine has the certain origin relation. Choropleth map of summed thickness of calcareous sandstone deserves that it mainly appear in area of uranium body and related cause of formation of ore body of interlayer deacidizing--oxidation belt. (authors)

Greenhouse gas emissions from hydroelectric reservoirs

International Nuclear Information System (INIS)

Rosa, L.P.; Schaeffer, R.

1994-01-01

In a recent paper, Rudd et al. have suggested that, per unit of electrical energy produced, greenhouse-gas emissions from some hydroelectric reservoirs in northern Canada may be comparable to emissions from fossil-fuelled power plants. The purpose of this comment is to elaborate these issues further so as to understand the potential contribution of hydroelectric reservoirs to the greenhouse effect. More than focusing on the total budget of carbon emissions (be they in the form of CH 4 or be they in the form of CO 2 ), this requires an evaluation of the accumulated greenhouse effect of gas emissions from hydroelectric reservoirs and fossil-fuelled power plants. Two issues will be considered: (a) global warming potential (GWP) for CH 4 ; and (b) how greenhouse-gas emissions from hydroelectric power plants stand against emissions from fossil-fuelled power plants with respect to global warming

Dzhezkazgan and associated sandstone copper deposits of the Chu-Sarysu basin, Central Kazakhstan

Science.gov (United States)

Box, Stephen E.; Seltmann, Reimar; Zientek, Michael L.; Syusyura, Boris; Creaser, Robert A.; Dolgopolova, Alla

2012-01-01

Sandstone-hosted copper (sandstone Cu) deposits occur within a 200-km reach of the northern Chu-Sarysu basin of central Kazakhstan (Dzhezkazgan and Zhaman-Aibat deposits, and the Zhilandy group of deposits). The deposits consist of Cu sulfide minerals as intergranular cement and grain replacement in 10 ore-bearing members of sandstone and conglomerate within a 600- to 1,000-m thick Pennsylvanian fluvial red-bed sequence. Copper metal content of the deposits ranges from 22 million metric tons (Mt, Dzehzkazgan) to 0.13Mt (Karashoshak in the Zhilandy group), with average grades of 0.85 to 1.7% Cu and significant values for silver (Ag) and rhenium (Re). Broader zones of iron reduction (bleaching) of sandstones and conglomerates of the red-bed sequence extend over 10 km beyond each of the deposits along E-NE-trending anticlines, which began to form in the Pennsylvanian. The bleached zones and organic residues within them are remnants of ormer petroleum fluid accumulations trapped by these anticlines. Deposit sites along these F1anticlines are localized at and adjacent to the intersections of nearly orthogonal N-NW-trending F2synclines. These structural lows served to guide the flow of dense ore brines across the petroleum-bearing anticlines, resulting in ore sulfide precipitation where the two fluids mixed. The ore brine was sourced either from the overlying Early Permian lacustrine evaporitic basin, whose depocenter occurs between the major deposits, or from underlying Upper Devonian marine evaporites. Sulfur isotopes indicate biologic reduction of sulfate but do not resolve whether the sulfate was contributed from the brine or from the petroleum fluids. New Re-Os age dates of Cu sulfides from the Dzhezkazgan deposit indicate that mineralization took place between 299 to 309 Ma near the Pennsylvanian-Permian age boundary. At the Dzhezkazgan and some Zhilandy deposits, F2fold deformation continued after ore deposition. Copper orebodies in Lower Permian

Advances in coalbed methane reservoirs using integrated reservoir characterization and hydraulic fracturing in Karaganda coal basin, Kazakhstan

Science.gov (United States)

Ivakhnenko, Aleksandr; Aimukhan, Adina; Kenshimova, Aida; Mullagaliyev, Fandus; Akbarov, Erlan; Mullagaliyeva, Lylia; Kabirova, Svetlana; Almukhametov, Azamat

2017-04-01

Coalbed methane from Karaganda coal basin is considered to be an unconventional source of energy for the Central and Eastern parts of Kazakhstan. These regions are situated far away from the main traditional sources of oil and gas related to Precaspian petroleum basin. Coalbed methane fields in Karaganda coal basin are characterized by geological and structural complexity. Majority of production zones were characterized by high methane content and extremely low coal permeability. The coal reservoirs also contained a considerable natural system of primary, secondary, and tertiary fractures that were usually capable to accommodate passing fluid during hydraulic fracturing process. However, after closing was often observed coal formation damage including the loss of fluids, migration of fines and higher pressures required to treat formation than were expected. Unusual or less expected reservoir characteristics and values of properties of the coal reservoir might be the cause of the unusual occurred patterns in obtained fracturing, such as lithological peculiarities, rock mechanical properties and previous natural fracture systems in the coals. Based on these properties we found that during the drilling and fracturing of the coal-induced fractures have great sensitivity to complex reservoir lithology and stress profiles, as well as changes of those stresses. In order to have a successful program of hydraulic fracturing and avoid unnecessary fracturing anomalies we applied integrated reservoir characterization to monitor key parameters. In addition to logging data, core sample analysis was applied for coalbed methane reservoirs to observe dependence tiny lithological variations through the magnetic susceptibility values and their relation to permeability together with expected principal stress. The values of magnetic susceptibility were measured by the core logging sensor, which is equipped with the probe that provides volume magnetic susceptibility parameters

Evaluating reservoir aspects from database on infill/step-out wells

Energy Technology Data Exchange (ETDEWEB)

Springer, S.J. [Springer Consulting Services, Calgary, AB (Canada)

2006-07-01

Statistical plots of production data were used as the basis for calculating simple parameters in order to develop insights into the performance of infill wells drilled in the Western Canadian Sedimentary Basin (WCSB). Unique characteristics of the performance of wells drilled in different parts of the basin were also discussed with the aim of assisting in the screening of future infill drilling projects. The aim of the paper was to demonstrate the effectiveness of a simple statistical analysis of the performance curves and to determine a method of characterizing lateral heterogeneity as well as risks in developing similar pools by infill drilling. The main data sources were the provincial Oil and Gas Reserves Books. Production data were obtained from a commercial data base. Data from wells at a heavy oil sandstone reservoir and a shallow sandstone gas reservoir were evaluated. In both pools, the horizontal infill wells performed better than the vertical wells.The initial rate of the median well was obtained by referencing the wells to its start time. A rate time plot for the first 5 years was prepared for the median wells. Similar plots for the average, 25 and 75 percentile wells were also generated. A cumulative production-frequency plot was generated for each pool. Most of the plots showed a fairly linear trend, reflecting a lognormal distribution. The slope of the lognormal plot reflected the lateral heterogeneity within the prospect. It was concluded that the analysis of the rate-cumulative production plot provided a method of accessing which percentages of the production were incremental reserves and which percentage were accelerated production. 7 refs., 9 tabs., 7 figs.

Chapter 2. Assessment of undiscovered conventional oil and gas resources--Upper Jurassic-Lower Cretaceous Cotton Valley group, Jurassic Smackover interior salt basins total petroleum system, in the East Texas basin and Louisiana-Mississippi salt basins provinces.

Science.gov (United States)

Dyman, T.S.; Condon, S.M.

2006-01-01

The Jurassic Smackover Interior Salt Basins Total Petroleum System is defined for this assessment to include (1) Upper Jurassic Smackover Formation carbonates and calcareous shales and (2) Upper Jurassic and Lower Cretaceous Cotton Valley Group organic-rich shales. The Jurassic Smackover Interior Salt Basins Total Petroleum System includes four conventional Cotton Valley assessment units: Cotton Valley Blanket Sandstone Gas (AU 50490201), Cotton Valley Massive Sandstone Gas (AU 50490202), Cotton Valley Updip Oil and Gas (AU 50490203), and Cotton Valley Hypothetical Updip Oil (AU 50490204). Together, these four assessment units are estimated to contain a mean undiscovered conventional resource of 29.81 million barrels of oil, 605.03 billion cubic feet of gas, and 19.00 million barrels of natural gas liquids. The Cotton Valley Group represents the first major influx of clastic sediment into the ancestral Gulf of Mexico. Major depocenters were located in south-central Mississippi, along the Louisiana-Mississippi border, and in northeast Texas. Reservoir properties and production characteristics were used to identify two Cotton Valley Group sandstone trends across northern Louisiana and east Texas: a high-permeability blanket-sandstone trend and a downdip, low-permeability massive-sandstone trend. Pressure gradients throughout most of both trends are normal, which is characteristic of conventional rather than continuous basin-center gas accumulations. Indications that accumulations in this trend are conventional rather than continuous include (1) gas-water contacts in at least seven fields across the blanket-sandstone trend, (2) relatively high reservoir permeabilities, and (3) high gas-production rates without fracture stimulation. Permeability is sufficiently low in the massive-sandstone trend that gas-water transition zones are vertically extensive and gas-water contacts are poorly defined. The interpreted presence of gas-water contacts within the Cotton Valley

Water Vapor Diffusion and Adsorption of Sandstones: Influence of Rock Texture and Composition

Directory of Open Access Journals (Sweden)

Martin Keppert

2016-01-01

Full Text Available The term sandstone is used for wide range of rocks containing quartz clasts which can be cemented by secondary precipitated quartz or calcite; moreover the space between clasts can be filled by matrix. These facts result in existence of numerous rocks having highly various properties. Sandstones have been used as construction materials due to their good accessibility and workability. Since most of sandstones are porous, water vapor can penetrate through sandstone constructions. The rate of water vapor diffusion, as well as the vapor sorption isotherm, was determined for range of sandstone types. The diffusion resistance factor was found to be dependent on the total porosity of sandstone but the sorption behavior was strongly influenced by nature of the particular sandstone; the specific surface area of stone and presence of clay matrix are determining its sorption isotherm. The published data enable estimating (i diffusion resistance factor of a sandstone via knowledge of its total porosity and (ii the sorption isotherm via knowledge of the stone’s nature and specific surface area. This approach can significantly reduce the time necessary to acquire vapor-related properties of a sandstone.

Determination of the Representative Elementary Volume for the study of sandstones and siltstones by X-Ray microtomography

Directory of Open Access Journals (Sweden)

Jaquiel Salvi Fernandes

2012-08-01

Full Text Available X-Ray computerized microtomography (µ-CT besides providing two-dimensional images (2-D of the transversal sections of the sample, the biggest attraction of the methodology is the rendering of three-dimensional images (3-D, enabling a more real analysis of the porous structure of the rock. However, the reconstruction, visualization and analysis of such 3-D images are limited in computer terms. Thus, it is not always possible to reconstruct the images with the total size of the microtomographed sample. Therefore, this study aims at determining the Representative Elementary Volume (REV in reservoir rocks concerning their porosity. In order to collect microtomographic data from reservoir rocks, a microtomograph Skyscan model 1172 was utilized for the sandstone and siltstone samples scanning. After the analysis of the graphs obtained by REV, it was concluded that the most adequate dimensions for the reconstructed volume in each analyzed sample were approximately 1400 × 1400 × 1400 µm, which are dimensions that can easily be reconstructed, visualized and analyzed.

PP and PS seismic response from fractured tight gas reservoirs: a case study

International Nuclear Information System (INIS)

Jianming, Tang; Shaonan, Zhang; Li, Xiang-Yang

2008-01-01

In this paper, we present an example of using PP and PS converted-wave data recorded by digital micro-eletro-mechanical-systems (MEMS) to evaluate a fractured tight gas reservoir from the Xinchang gas field in Sichuan, China. For this, we analyse the variations in converted shear-wave splitting, Vp/Vs ratio and PP and PS impedance, as well as other attributes based on absorption and velocity dispersion. The reservoir formation is tight sandstone, buried at a depth of about 5000 m, and the converted-wave data reveal significant shear-wave splitting over the reservoir formation. We utilize a rotation technique to extract the shear-wave polarization and time delay from the data, and a small-window correlation method to build time-delay spectra that allow the generation of a time-delay section. At the reservoir formation, the shear-wave time delay is measured at 20 ms, about 15% shear-wave anisotropy, correlating with the known gas reservoirs. Furthermore, the splitting anomalies are consistent with the characteristics of other attributes such as Vp/Vs ratio and P- and S-wave acoustic and elastic impedance. The P-wave shows consistent low impedance over the reservoir formation, whilst the S-wave impedance shows relatively high impedance. The calculated gas indicator based on absorption and velocity dispersion yields a high correlation with the gas bearing formations. This confirms the benefit of multicomponent seismic data from digital MEMS sensors

Understanding creep in sandstone reservoirs – theoretical deformation mechanism maps for pressure solution in granular materials

NARCIS (Netherlands)

Hangx, Suzanne; Spiers, Christopher

Subsurface exploitation of the Earth’s natural resources removes the natural system from its chemical and physical equilibrium. As such, groundwater extraction and hydrocarbon production from subsurface reservoirs frequently causes surface subsidence and induces (micro)seismicity. These effects are

Predictability of Western Himalayan river flow: melt seasonal inflow into Bhakra Reservoir in northern India

Directory of Open Access Journals (Sweden)

I. Pal

2013-06-01

Full Text Available Snowmelt-dominated streamflow of the Western Himalayan rivers is an important water resource during the dry pre-monsoon spring months to meet the irrigation and hydropower needs in northern India. Here we study the seasonal prediction of melt-dominated total inflow into the Bhakra Dam in northern India based on statistical relationships with meteorological variables during the preceding winter. Total inflow into the Bhakra Dam includes the Satluj River flow together with a flow diversion from its tributary, the Beas River. Both are tributaries of the Indus River that originate from the Western Himalayas, which is an under-studied region. Average measured winter snow volume at the upper-elevation stations and corresponding lower-elevation rainfall and temperature of the Satluj River basin were considered as empirical predictors. Akaike information criteria (AIC and Bayesian information criteria (BIC were used to select the best subset of inputs from all the possible combinations of predictors for a multiple linear regression framework. To test for potential issues arising due to multicollinearity of the predictor variables, cross-validated prediction skills of the best subset were also compared with the prediction skills of principal component regression (PCR and partial least squares regression (PLSR techniques, which yielded broadly similar results. As a whole, the forecasts of the melt season at the end of winter and as the melt season commences were shown to have potential skill for guiding the development of stochastic optimization models to manage the trade-off between irrigation and hydropower releases versus flood control during the annual fill cycle of the Bhakra Reservoir, a major energy and irrigation source in the region.

Study of the reactive processes during CO2 injection into sedimentary reservoirs: Experimental quantification of the processes at meso-scale

International Nuclear Information System (INIS)

Luquot, L.

2008-11-01

In order to minimize CO 2 atmospheric concentration, a solution consists in sequestrating CO 2 in geological reservoirs. To estimate long term risks, it is necessary to quantify the couplings between reaction processes as well as structural and hydrodynamical modifications. We realised two experimental benches enabling injecting CO 2 -enriched-brine in conditions corresponding to in situ storage (T ≤ 200 C and P ≤ 200 bar) and developed an experimental protocol using X-Ray microtomography and fluid and rock analyses in order to measure the variations of physical and chemical parameters. The study of carbonated reservoirs near the injection well, allows quantifying different k-phi relationships depending on the dissolution processes and triggered by the local fluid chemical composition and initials conditions. Away from the injection well, we observe carbonate precipitation decreasing the permeability. The study of fractured cap-rock samples shows that alternative percolation of CO 2 -enriched-brine and CO 2 gas increases the fracture permeability. The study of silicated rocks indicates carbonate precipitation in zeolite sandstone and sintered dunite grains. Nevertheless, in zeolite sandstone we also observe the precipitation of clay particles located in the fluid pathways which decrease strongly the permeability. (author)

Mittelplate A23/A23M1. Geological and reservoir engineering concept of a dual-lateral well; Mittelplate A23/A23M1. Geologisches und lagerstaettentechnisches Konzept einer Duolateralbohrung

Energy Technology Data Exchange (ETDEWEB)

Osivandi, K.; Racher, D. [RWE Dea AG, Hamburg (Germany)

2011-07-15

The Mittelplate Oil Field is situated in the German Wadden Sea in the West Holstein Trough in the concession Heide/Buesum, about 100 km northwest of Hamburg. Operator is RWE Dea AG (50%), and the partner is Wintershall Holding GmbH (50%). Besides the reservoir layers of the Dogger Gamma, Delta, Epsilon, and Zeta, the shallow-marine/deltaic sandstone-shale-succession of the Dogger Beta (with its five oil-bearing sandstones of 1-5 m thickness each) forms the laterally widespread reservoir which was the target for Germany's and RWE Dea AG's first pressure-tight multilateral well. So far the Dogger-Beta-Reservoir has been developed with wells from the artificial island Mittelplate A using a 5-spot pattern with a successive concentric concept. In order to reduce the costs and effectively make use of the limited amount of slots, the development concept should be improved by implementing the multilateral technology. By targeting three drainage areas in total, the multilateral well Mittelplate A23/A23M1 was planned to produce oil at an initial rate of ca. 400 m{sup 3}/d. In order to achieve a horizontal interval of ca. 2640 m length, several LWD measurements including Gamma Ray- and Density- Images and Deep-Directional-Resistivity logs were necessary. The long horizontal exposure of the oil-bearing sandstone layers as well as the tangent sections for placement of the electrical submersible pump (ESP) and junction above the reservoir represented the main challenges during geological planning and realtime geosteering. A total perforation length of 1360 m was achieved, taking into account the required distances to neighboring producer wells and the laterally varying pore pressures. According to the latest production history of the well, a cumulative production of about 10% more than initially planned are expected after an initial production rate of 735 m{sup 3}/d. Thanks to the successful application of the multilateral technology and geosteering within the thin

Elementary analysis on the main factors affecting the permeability of sandstones

International Nuclear Information System (INIS)

Gong Binli

2006-01-01

Researches show that in the early stage of sandstone diagenesis, compaction, pressure solution, cementation and replacement reduce both the porosity and the permeability. The cementation of authigenic kaolinite may preserve the tiny intergranular pore-space, and slightly influence the porosity, and even increase the permeability. During the middle to late stage of diagenesis, the organic matter becomes matured, hydrocarbon and acidic water are produced, which forms secondary porosity by the dissolution and the corrosion, and greatly increases the permeability of sandstones and provides a favorable prerequisite for the formation of sandstone-type uranium deposits. The interlayered oxidation alteration, oil-gas reduction and low-temperature hydrothermal alteration also produce secondary porosity in epigenetic reforming stage, which finally decides the permeability after the formation of sandstone-type uranium deposits. This is an important condition for in-situ leaching of sandstone-type uranium deposit. (authors)

Assessment of managed aquifer recharge at Sand Hollow Reservoir, Washington County, Utah, updated to conditions in 2012

Science.gov (United States)

Marston, Thomas M.; Heilweil, Victor M.

2013-01-01

Sand Hollow Reservoir in Washington County, Utah, was completed in March 2002 and is operated primarily for managed aquifer recharge by the Washington County Water Conservancy District. From 2002 through 2011, surface-water diversions of about 199,000 acre-feet to Sand Hollow Reservoir have allowed the reservoir to remain nearly full since 2006. Groundwater levels in monitoring wells near the reservoir rose through 2006 and have fluctuated more recently because of variations in reservoir altitude and nearby pumping from production wells. Between 2004 and 2011, a total of about 19,000 acre-feet of groundwater was withdrawn by these wells for municipal supply. In addition, a total of about 21,000 acre-feet of shallow seepage was captured by French drains adjacent to the North and West Dams and used for municipal supply, irrigation, or returned to the reservoir. From 2002 through 2011, about 106,000 acre-feet of water seeped beneath the reservoir to recharge the underlying Navajo Sandstone aquifer. Water quality was sampled at various monitoring wells in Sand Hollow to evaluate the timing and location of reservoir recharge as it moved through the aquifer. Tracers of reservoir recharge include major and minor dissolved inorganic ions, tritium, dissolved organic carbon, chlorofluorocarbons, sulfur hexafluoride, and noble gases. By 2012, this recharge arrived at four monitoring wells located within about 1,000 feet of the reservoir. Changing geochemical conditions at five other monitoring wells could indicate other processes, such as changing groundwater levels and mobilization of vadose-zone salts, rather than arrival of reservoir recharge.

Evolution of the Petrophysical and Mineralogical Properties of Two Reservoir Rocks Under Thermodynamic Conditions Relevant for CO2 Geological Storage at 3 km Depth

International Nuclear Information System (INIS)

Rimmel, G.; Barlet-Gouedard, V.; Renard, F.

2010-01-01

Injection of carbon dioxide (CO 2 ) underground, for long-term geological storage purposes, is considered as an economically viable option to reduce greenhouse gas emissions in the atmosphere. The chemical interactions between supercritical CO 2 and the potential reservoir rock need to be thoroughly investigated under thermodynamic conditions relevant for geological storage. In the present study, 40 samples of Lavoux limestone and Adamswiller sandstone, both collected from reservoir rocks in the Paris basin, were experimentally exposed to CO 2 in laboratory autoclaves specially built to simulate CO 2 -storage-reservoir conditions. The two types of rock were exposed to wet supercritical CO 2 and CO 2 -saturated water for one month, at 28 MPa and 90 C, corresponding to conditions for a burial depth approximating 3 km. The changes in mineralogy and micro-texture of the samples were measured using X-ray diffraction analyses, Raman spectroscopy, scanning-electron microscopy, and energy-dispersion spectroscopy microanalysis. The petrophysical properties were monitored by measuring the weight, density, mechanical properties, permeability, global porosity, and local porosity gradients through the samples. Both rocks maintained their mechanical and mineralogical properties after CO 2 exposure despite an increase of porosity and permeability. Microscopic zones of calcite dissolution observed in the limestone are more likely to be responsible for such increase. In the sandstone, an alteration of the petro-fabric is assumed to have occurred due to clay minerals reacting with CO 2 . All samples of Lavoux limestone and Adamswiller sandstone showed a measurable alteration when immersed either in wet supercritical CO 2 or in CO 2 -saturated water. These batch experiments were performed using distilled water and thus simulate more severe conditions than using formation water (brine). (authors)

Vegetative substrates used by larval northern pike in Rainy and Kabetogama Lakes, Minnesota

Science.gov (United States)

Anne L. Timm; Rodney B. Pierce

2015-01-01

Our objective was to identify characteristics of aquatic vegetative communities used as larval northern pike nursery habitat in Rainy and Kabetogama lakes, glacial shield reservoirs in northern Minnesota. Quatrefoil light traps fished at night were used to sample larval northern pike in 11 potential nursery areas. Larval northern pike were most commonly sampled among...

3D Sedimentological and geophysical studies of clastic reservoir analogs: Facies architecture, reservoir properties, and flow behavior within delta front facies elements of the Cretaceous Wall Creek Member, Frontier Formation, Wyoming

Energy Technology Data Exchange (ETDEWEB)

Christopher D. White

2009-12-21

Significant volumes of oil and gas occur in reservoirs formed by ancient river deltas. This has implications for the spatial distribution of rock types and the variation of transport properties. A between mudstones and sandstones may form baffles that influence productivity and recovery efficiency. Diagenetic processes such as compaction, dissolution, and cementation can also alter flow properties. A better understanding of these properties and improved methods will allow improved reservoir development planning and increased recovery of oil and gas from deltaic reservoirs. Surface exposures of ancient deltaic rocks provide a high-resolution view of variability. Insights gleaned from these exposures can be used to model analogous reservoirs, for which data is sparser. The Frontier Formation in central Wyoming provides an opportunity for high-resolution models. The same rocks exposed in the Tisdale anticline are productive in nearby oil fields. Kilometers of exposure are accessible, and bedding-plane exposures allow use of high-resolution ground-penetrating radar. This study combined geologic interpretations, maps, vertical sections, core data, and ground-penetrating radar to construct geostatistical and flow models. Strata-conforming grids were use to reproduce the observed geometries. A new Bayesian method integrates outcrop, core, and radar amplitude and phase data. The proposed method propagates measurement uncertainty and yields an ensemble of plausible models for calcite concretions. These concretions affect flow significantly. Models which integrate more have different flow responses from simpler models, as demonstrated an exhaustive two-dimensional reference image and in three dimensions. This method is simple to implement within widely available geostatistics packages. Significant volumes of oil and gas occur in reservoirs that are inferred to have been formed by ancient river deltas. This geologic setting has implications for the spatial distribution of

Characterization of application of acu sandstone in ceramic mass

International Nuclear Information System (INIS)

Nobrega, L.F.P.M.; Souza, M.M.; Gomes, Y.S.; Fernandes, D.L.

2016-01-01

The sandstone is a sedimentary rock formed mainly by quartz grains. In Rio Grande do Norte, there is the Potiguar Basin with the Jandaira and Acu Formations. The latter consists of thick layers of whitish-colored sandstones. It stands out as a water storage facility in the state, but it is also used for building aggregates. This article aimed at the use of the sandstone of this formation in the ceramic mass for coating. Initially, the material was sampled. It went through the comminution process to achieve the required granulometry. After this, three formulations were made to incorporate this new material into the traditional ones. The methods were performed according to ISO 13816. After sintering at 1200 °C, the specimens were subjected to the physical tests. A positive result was obtained for the use of the Acu sandstone in low concentrations. It is clear, therefore, its use in ceramics for coating

Examples from the 1.6 Ga Chorhat Sandstone, Vindhyan

Indian Academy of Sciences (India)

This paper addresses macroscopic signatures of microbial mat-related structures within the 1.6 Ga-old Chorhat Sandstone of the Semri Group –the basal stratigraphic unit of the Vindhyan succession in Son valley.The Chorhat Sandstone broadly represents a prograding succession of three depositional facies ranging from ...

Hydrology of the Ferron sandstone aquifer and effects of proposed surface-coal mining in Castle Valley, Utah, with sections on stratigraphy and leaching of overburden

Science.gov (United States)

Lines, Gregory C.; Morrissey, Daniel J.; Ryer, Thomas A.; Fuller, Richard H.

1983-01-01

Coal in the Ferron Sandstone Member of the Mancos Shale of Cretaceous age has traditionally been mined by underground techniques in the Emery Coal Field in the southern end of Castle Valley in east-central Utah. However, approximately 99 million tons are recoverable by surface mining. Ground water in the Ferron is the sole source of supply for the town of Emery, but the aquifer is essentially untapped outside the Emery area.The Ferron Sandstone Member crops out along the eastern edge of Castle Valley and generally dips 2 ? to 10 ? to the northwest. Sandstones in the Ferron are enclosed between relatively impermeable shale in the Tununk and Blue Gate Members of the Mancos Shale. Along the outcrop, the Ferron ranges in thickness from about 80 feet in the northern part of Castle Valley to 850 feet in the southern part. The Ferron also generally thickens in the subsurface downdip from the outcrop. Records from wells and test holes indicate that the full thickness of the Ferron is saturated with water in most areas downdip from the outcrop area.Tests in the Emery area indicate that transmissivity of the Ferron sandstone aquifer ranges from about 200 to 700 feet squared per day where the Ferron is fully saturated. Aquifer transmissivity is greatest near the Paradise Valley-Joes Valley fault system where permeability has been increased by fracturing. Storage coefficient ranges from about 10 .6 to 10 -3 where the Ferron sandstone aquifer is confined and probably averages 5 x 10-2 where it is unconfined.

Trilobites from the Middle Ordovician Stairway Sandstone, Amadeus Basin, central Australia

DEFF Research Database (Denmark)

Jakobsen, Kristian Grube; Nielsen, Arne Thorshøj; Harper, David Alexander Taylor

2014-01-01

During the Middle Ordovician (Darriwilian) sandstones and siltstones were deposited in the epicontinental Larapintine Sea, which covered large parts of central Australia. The Darriwilian Stairway Sandstone has, for the first time, been sampled stratigraphically for macrofossils to track marine...... benthic biodiversity in this clastic-dominated shallow-water palaeoenvironment situated along the margin of northeastern Gondwana. The faunas from the Stairway Sandstone are generally of low diversity and dominated by bivalves but include several animal groups, with trilobites representing 25......% of the entire shelly fauna. Thirteen trilobite taxa are described from the Stairway Sandstone; the fauna displays a high degree of endemism. One new species, Basilicus (Parabasilicus) brumbyensis sp. nov. is described....

Preliminary study of the uranium potential of the northern part of the Durham Triassic Basin, North Carolina

International Nuclear Information System (INIS)

Harris, W.B.; Thayer, P.A.

1981-09-01

This report presents results of a four-channel spectrometric survey of the northern part of the Durham Triassic basin and adjacent Piedmont, North Carolina. Gamma-ray spectrometric measurements were obtained at 112 localities from 136 different lithologies. The nominal sampling density in the Durham Basin is one site per 2 mi 2 . Surface radiometric surveys reveal no anomalous radioactivity in the northern part of the Durham Basin. Uranium concentrations in Triassic rocks are from 0.6 to 9.7 ppM and average 2.9 ppM. Mudrocks contain from 1.3 to 9.7 ppM, and the average is 4.5 ppM. Sandstones contain from 0.6 to 8.8 ppM, and the average is 2.5 ppM. Fanglomerates contain the lowest concentrations of uranium, from 1.4 to 2.0 ppM, for an average of 1.8 ppM. Uranium/thorium ratios average 0.27 for Triassic rocks and are from 0.04 to 1.85. The mean log uranium/log thorium for Triassic rocks is 0.37. Mudrock has the highest average uranium/thorium ratio (0.32), and the range is 0.09 to 0.66. Sandstones have an average uranium/thorium ratio of 0.26, and the range is 0.04 to 1.85. Fanglomerates have the lowest range uranium/thorium ratio (0.19), and the range is 0.12 to 0.19. On the basis of surface radiometric surveys and geologic studies, it is believed that sedimentary strata in the northern part of the Durham Basin are poor targets for further uranium exploration. This conclusion is based on the lack of favorable characteristics commonly present in fluvial uranium deposits. Among these are: (1) carbonaceous material is absent in Triassic rocks of the northern basin, (2) indicators of a reduzate facies in sandstones are not present, and (3) no tuffaceous beds are associated with sediments in the northern Durham Basin

Impacts, Perceptions and Management of Climate-Related Risks to Cage Aquaculture in the Reservoirs of Northern Thailand.

Science.gov (United States)

Lebel, Louis; Lebel, Phimphakan; Lebel, Boripat

2016-12-01

Weather is suspected to influence fish growth and survival, and be a factor in mass mortality events in cage aquaculture in reservoirs. The purpose of this study was to identify the important climate-related risks faced by cage aquaculture farms; evaluate how these risks were currently being managed; and explore how farmers might adapt to the effects of climate change. Fish farmers were interviewed across the northern region of Thailand to get information on impacts, perceptions and practices. Drought or low water levels, heat waves, cold spells and periods with dense cloud cover, each caused significant financial losses. Perceptions of climate-related risks were consistent with experienced impacts. Risks are primarily managed in the short-term with techniques like aeration and reducing feed. In the mid-term farmers adjust stocking calendars, take financial measures and seek new information. Farmers also emphasize the importance of maintaining good relations with other stakeholders and reservoir management. Larger farms placed greater importance on risk management than small farms, even though types and levels of risk perceived were very similar. Most fish farms were managed by men alone, or men and women working together. Gender differences in risk perception were not detected, but women judged a few risk management practices as more important than men. Fish farmers perceived that climate is changing, but their perceptions were not strongly associated with recently having suffered impacts from extreme weather. The findings of this study provide important inputs to improving risk management under current and future climate.

Volcanic settings and their reservoir potential: An outcrop analog study on the Miocene Tepoztlán Formation, Central Mexico

Science.gov (United States)

Lenhardt, Nils; Götz, Annette E.

2011-07-01

The reservoir potential of volcanic and associated sedimentary rocks is less documented in regard to groundwater resources, and oil and gas storage compared to siliciclastic and carbonate systems. Outcrop analog studies within a volcanic setting enable to identify spatio-temporal architectural elements and geometric features of different rock units and their petrophysical properties such as porosity and permeability, which are important information for reservoir characterization. Despite the wide distribution of volcanic rocks in Mexico, their reservoir potential has been little studied in the past. In the Valley of Mexico, situated 4000 m above the Neogene volcanic rocks, groundwater is a matter of major importance as more than 20 million people and 42% of the industrial capacity of the Mexican nation depend on it for most of their water supply. Here, we present porosity and permeability data of 108 rock samples representing five different lithofacies types of the Miocene Tepoztlán Formation. This 800 m thick formation mainly consists of pyroclastic rocks, mass flow and fluvial deposits and is part of the southern Transmexican Volcanic Belt, cropping out south of the Valley of Mexico and within the two states of Morelos and Mexico State. Porosities range from 1.4% to 56.7%; average porosity is 24.8%. Generally, permeabilities are low to median (0.2-933.3 mD) with an average permeability of 88.5 mD. The lavas are characterized by the highest porosity values followed by tuffs, conglomerates, sandstones and tuffaceous breccias. On the contrary, the highest permeabilities can be found in the conglomerates, followed by tuffs, tuffaceous breccias, sandstones and lavas. The knowledge of these petrophysical rock properties provides important information on the reservoir potential of volcanic settings to be integrated to 3D subsurface models.

Uranium distribution and sandstone depositional environments: oligocene and upper Cretaceous sediments, Cheyenne basin, Colorado

International Nuclear Information System (INIS)

Nibbelink, K.A.; Ethridge, F.G.

1984-01-01

Wyoming-type roll-front uranium deposits occur in the Upper Cretaceous Laramie and Fox Hills sandstones in the Cheyenne basin of northeastern Colorado. The location, geometry, and trend of specific depositional environments of the Oligocene White River and the Upper Cretaceous Laramie and Fox Hills formations are important factors that control the distribution of uranium in these sandstones. The Fox Hills Sandstone consists of up to 450 ft (140 m) of nearshore marine wave-dominated delta and barrier island-tidal channel sandstones which overlie offshore deposits of the Pierre Shale and which are overlain by delta-plain and fluvial deposits of the Laramie Formation. Uranium, which probably originated from volcanic ash in the White River Formation, was transported by groundwater through the fluvial-channel deposits of the White River into the sandstones of the Laramie and Fox Hills formations where it was precipitated. Two favorable depositional settings for uranium mineralization in the Fox Hills Sandstone are: (1) the landward side of barrier-island deposits where barrier sandstones thin and interfinger with back-barrier organic mudstones, and (2) the intersection of barrier-island and tidal channel sandstones. In both settings, sandstones were probably reduced during early burial by diagenesis of contained and adjacent organic matter. The change in permeability trends between the depositional strike-oriented barrier sandstones and the dip-oriented tidal-channel sandstones provided sites for dispersed groundwater flow and, as demonstrated in similar settings in other depositional systems, sites for uranium mineralization

System-Wide Significance of Predation on Juvenile Salmonids in Columbia and Snake River Reservoirs : Annual Report 1992.

Energy Technology Data Exchange (ETDEWEB)

Petersen, James H.; Poe, Thomas P.

1993-12-01

Northern squawfish (Ptychocheilus oregonensis) predation on juvenile salmonids was characterized during 1992 at ten locations in the Columbia River below Bonneville Dam and at three locations in John Day Reservoir. During the spring and summer, 1,487 northern squawfish were collected in the lower Columbia River and 202 squawfish were sampled in John Day Reservoir. Gut content data, predator weight, and water temperature were used to compute a consumption index (CI) for northern squawfish, and overall diet was also described. In the Columbia River below Bonneville Dam, northern squawfish diet was primarily fish (spring 69%; summer 53%), most of which were salmonids. Salmonids were also the primary diet component in the Bonneville Dam tailrace, John Day Dam forebay, and the McNary Dam tailrace. Crustaceans were the dominant diet item at the John Day mid-reservoir location, although sample sizes were small. About half of the non-salmonid preyfish were sculpins. The consumption index (CI) of northern squawfish was generally higher during summer than during spring. The highest CI`s were observed during summer in the tailrace boat restricted zones of Bonneville Dam (CI = 7.8) and McNary Dam (CI = 4.6). At locations below Bonneville Dam, CI`s were relatively low near Covert`s Landing and Rooster Rock, higher at four locations between Blue Lake and St. Helens, and low again at three downriver sites (Kalama, Ranier, and Jones Beach). Northern squawfish catches and CI`s were noticeably higher throughout the lower Columbia compared to mid-reservoir sites further upriver sampled during 1990--92. Predation may be especially intense in the free-flowing section of the Columbia River below Bonneville Dam. Smallmouth bass (Micropterus dolomieui; N = 198) ate mostly fish -- 25% salmonids, 29% sculpins, and 46% other fish. Highest catches of smallmouth bass were in the John Day Dam forebay.

Geologic and engineering characterization of Geraldine Ford field, Reeves and Culberson Counties, Texas. Topical report -- 1997

Energy Technology Data Exchange (ETDEWEB)

Dutton, S.P.; Malik, M.A.; Asquith, G.B.; Barton, M.D.; Cole, A.G.; Gogas, J.; Clift, S.J.; Guzman, J.I.

1998-04-01

The objective of this Class III project is to demonstrate that detailed reservoir characterization of clastic reservoirs in basinal sandstones of the Delaware Mountain Group in the Delaware Basin of West Texas and New Mexico is a cost-effective way to recover more of the original oil in place by strategic infill-well placement and geologically based field development. The study focused on Geraldine Ford field, which produces from the upper Bell Canyon formation (Ramsey sandstone). Petrophysical characterization of the Ford Geraldine unit was accomplished by integrating core and log data and quantifying petrophysical properties from wireline logs. The petrophysical data were used to map porosity, permeability, net pay, water saturation, mobile oil saturation, and other reservoir properties. Once the reservoir-characterization study was completed, a demonstration area of approximately 1 mi{sup 2} in the northern part of the unit was chosen for reservoir modeling/simulation. A quarter of a five-spot injection pattern in the demonstration area was selected for flow simulations, and two cases of permeability distribution were considered, one using stochastic permeability distribution generated by conditional simulation and the other using layered permeabilities. Flow simulations were performed using UTCOMP, an isothermal, three-dimensional, compositional simulator for miscible gas flooding. Results indicate that 10--30% (1 to 3 MMbbl) of remaining oil in place in the demonstration area can be produced by CO{sub 2} injection.

Fault features and enrichment laws of narrow-channel distal tight sandstone gas reservoirs: A case study of the Jurassic Shaximiao Fm gas reservoir in the Zhongjiang Gas Field, Sichuan Basin

Directory of Open Access Journals (Sweden)

Zhongping Li

2016-11-01

Full Text Available The Jurassic Shaximiao Fm gas reservoir in the Zhongjiang Gas Field, Sichuan Basin, is the main base of Sinopec Southwest Oil & Gas Company for gas reserves and production increase during the 12th Five-Year Plan. However, its natural gas exploration and development process was restricted severely, since the exploration wells cannot be deployed effectively in this area based on the previous gas accumulation and enrichment pattern of “hydrocarbon source fault + channel sand body + local structure”. In this paper, the regional fault features and the gas accumulation and enrichment laws were discussed by analyzing the factors like fault evolution, fault elements, fault-sand body configuration (the configuration relationship between hydrocarbon source faults and channel sand bodies, trap types, and reservoir anatomy. It is concluded that the accumulation and enrichment of the Shaximiao Fm gas reservoir in this area is controlled by three factors, i.e., hydrocarbon source, sedimentary facies and structural position. It follows the accumulation laws of source controlling region, facies controlling zone and position controlling reservoir, which means deep source and shallow accumulation, fault-sand body conductivity, multiphase channel, differential accumulation, adjusted enrichment and gas enrichment at sweet spots. A good configuration relationship between hydrocarbon source faults and channel sand bodies is the basic condition for the formation of gas reservoirs. Natural gas accumulated preferentially in the structures or positions with good fault-sand body configuration. Gas reservoirs can also be formed in the monoclinal structures which were formed after the late structural adjustment. In the zones supported by multiple faults or near the crush zones, no gas accumulation occurs, but water is dominantly produced. The gas-bearing potential is low in the area with undeveloped faults or being 30 km away from the hydrocarbon source faults. So

Aquifer prospect and vulnerability of Upper Maastrichtian sandstones: Case of Ajali and Nsukka formations in the Northern Enugu Province, southeastern Nigeria

Science.gov (United States)

Ukpai, Stephen N.; Ezeh, Hilary N.; Igwe, James O.

2017-11-01

Two typical aquifer systems, namely, regional aquifer and local Perched aquifer have been delineated in the study area. The regional aquifer was identified at about 100 m depth around lowland areas, although prone to polluting effects from farming activities, erosion and weathering processes. This study investigated extents of groundwater pollution and permeability of the aquifers from water sample and grain size analyses. Results show porosity ranging from 49 to 50% and hydraulic conductivities as follows: 7.0 m/day for the sandstone of Nsukka Formation, 34.6 m/day for the outcrop of Ajali sandstone and 10.4 m/day for the sandstone at saturated subsurface zone with transmissivity of about 572 m2/day. The results signify that the regional aquifer is recharged by substantial rate of infiltrations vis-a-vis surface outcrops, and is therefore vulnerable to infiltration of pollution plumes. The groundwater is mainly acidic at pH ranging from 5.05 to 7.41 with a mean value of about 6.48, hence the pollution from dissolved iron in many places. Three main water types were identified, namely, Ca-Mg-HCO3, Ca-HCO3-Cl2 and Mg-Na-HCO3-SO4-Cl2 facies, all signifying dominance of groundwater species arising from precipitation recharge. This has resulted in the influences of surface effluents from run off as indicated by nitrate pollution in some areas. Thus, active hydrologic cycle controls the chemical facies in the water resources of the region, and with its hydraulic influence on the landscape, the quality status of groundwater, as well as the growth of agricultural products have been impaired.

Sandstone-type uranium deposits. Summary and conclusions

International Nuclear Information System (INIS)

Finch, W.I.

1985-01-01

The similarity of most of the deposits described in this report is striking even though they occur in sandstone host rocks ranging in age from Carboniferous to Tertiary and on every continent outside the polar regions. Geologic environments of the uranium deposits consist of distinctive sets of tectonic and sedimentary-depositional systems, all of which have some common threads of favorable geologic processes. In this summary paper it is hoped that this report has sharpened an understanding of the deposit's ''home environment'' that will aid future exploration for these resource-important sandstone-type uranium ores

Selection of reservoirs amenable to micellar flooding. First annual report, October 1978-December 1979

Energy Technology Data Exchange (ETDEWEB)

Goldburg, A.; Price, H.

1980-12-01

The overall project objective is to build a solid engineering base upon which the Department of Energy (DOE) can improve and accelerate the application of micellar-polymer recovery technology to Mid-Continent and California sandstone reservoirs. The purpose of the work carried out under these two contracts is to significantly aid, both DOE and the private sector, in gaining the following Project Objectives: to select the better micellar-polymer prospects in the Mid-Continent and California regions; to assess all of the available field and laboratory data which has a bearing on recovering oil by micellar-polymer projects in order to help identify and resolve both the technical and economic constraints relating thereto; and to design and analyze improved field pilots and tests and to develop a micellar-polymer applications matrix for use by the potential technology users; i.e., owner/operators. The report includes the following: executive summary and project objectives; development of a predictive model for economic evaluation of reservoirs; reservoir data bank for micellar-polymer recovery evaluation; PECON program for preliminary economic evaluation; ordering of candidate reservoirs for additional data acquisition; validation of predictive model by numerical simulation; and work forecast. Tables, figures and references are included.

Modeling Reservoir-River Networks in Support of Optimizing Seasonal-Scale Reservoir Operations

Science.gov (United States)

Villa, D. L.; Lowry, T. S.; Bier, A.; Barco, J.; Sun, A.

2011-12-01

each timestep and minimize computational overhead. Power generation for each reservoir is estimated using a 2-dimensional regression that accounts for both the available head and turbine efficiency. The object-oriented architecture makes run configuration easy to update. The dynamic model inputs include inflow and meteorological forecasts while static inputs include bathymetry data, reservoir and power generation characteristics, and topological descriptors. Ensemble forecasts of hydrological and meteorological conditions are supplied in real-time by Pacific Northwest National Laboratory and are used as a proxy for uncertainty, which is carried through the simulation and optimization process to produce output that describes the probability that different operational scenario's will be optimal. The full toolset, which includes HydroSCOPE, is currently being tested on the Feather River system in Northern California and the Upper Colorado Storage Project.

Geological principles of exploration for sandstone-hosted uranium deposits

International Nuclear Information System (INIS)

Le Roux, J.P.

1982-10-01

Although the importance of sandstone-hosted uranium deposits has seemingly faded in recent years due to the discovery of large, high -grade deposits elsewhere, a forecasted energy shortage in the near future will probably necessitate a new look at sedimentary basins as a source of uranium. Back-arc basins adjacent to calcalkaline source areas are especially favourable if they are filled with fluvial, post-Devonian sediments. Syn- and post-depositional tectonics play an important role in the sedimentation-mineralisation process and should be investigated. The oxidation-reduction state of the sandstones is a valid prospecting tool. Sedimentological environments govern the permeability and vegetal matter content of sandstones and directly control uranium mineralisation

Analyzing the Sand-fixing Effect of Feldspathic Sandstone from the Texture Characteristics

Science.gov (United States)

Zhang, lu; Ban, Jichang

2018-01-01

The purpose of this research was aimed to study the sand fixing effect of feldspathic sandstone in Mu Us Sandy Land, to provide a scienticic basis for desertification control, soil and water conservation and development of farming there. Methods of mixing feldspathic sandstone and aeolian sandy soil according to 1: 0, 1: 1, 1: 2, 1: 5, and 0: 1 mass ratioes, the graded composition and characteristics were studied with laser particle size analyzer. The result showed that these features of sand-based, loosely structured, easy to wind erosion of aeolian sandy soil were changed before feldspathic sandstone and aeolian sandy soil compounding. The <0.05 mm particle mass increased with feldspathic sandstone mass increasing. The texture presented this kind of change from sand to sandy loam to loam to silt loam. The small particle size distribution, good homogeneity and other features of aeolian sandy soil were improved to a certain degree, and the particle size distribution became broad before feldspathic sandstone and aeolian sandy soil compounding. The particle grading was continuous, and the grading characteristic was good when m(F): m(S) was 1: 5(Cu was 54.71 and Cc was 2.54) or when m(F): m(S) was 1: 2(Cu was 76.21, Cc was 1.12). The conclusion is that feldspathic sandstone has sand-fixing effect in texture characteristics, which heightens with feldspathic sandstone mass increasing, and when the mass ratio of feldspathic sandstone: aeolian sandy soil is 1: 2 or 1: 5 which compound better.

Effects of heat-flow and hydrothermal fluids from volcanic intrusions on authigenic mineralization in sandstone formations

Directory of Open Access Journals (Sweden)

Wolela Ahmed

2002-06-01

Full Text Available Volcanic intrusions and hydrothermal activity have modified the diagenetic minerals. In the Ulster Basin, UK, most of the authigenic mineralization in the Permo-Triassic sandstones pre-dated tertiary volcanic intrusions. The hydrothermal fluids and heat-flow from the volcanic intrusions did not affect quartz and feldspar overgrowths. However, clay mineral-transformation, illite-smectite to illite and chlorite was documented near the volcanic intrusions. Abundant actinolite, illite, chlorite, albite and laumontite cementation of the sand grains were also documented near the volcanic intrusions. The abundance of these cementing minerals decreases away from the volcanic intrusions.In the Hartford Basin, USA, the emplacement of the volcanic intrusions took place simultaneous with sedimentation. The heat-flow from the volcanic intrusions and hydrothermal activity related to the volcanics modified the texture of authigenic minerals. Microcrystalline mosaic albite and quartz developed rather than overgrowths and crystals near the intrusions. Chlorite clumps and masses were also documented with microcrystalline mosaic albite and quartz. These features are localized near the basaltic intrusions. Laumontite is also documented near the volcanic intrusions. The reservoir characteristics of the studied sandstone formations are highly affected by the volcanic and hydrothermal fluids in the Hartford and the Ulster Basin. The porosity dropped from 27.4 to zero percent and permeability from 1350 mD to 1 mD.

Understanding and Mitigating Reservoir Compaction: an Experimental Study on Sand Aggregates

Science.gov (United States)

Schimmel, M.; Hangx, S.; Spiers, C. J.

2016-12-01

Fossil fuels continue to provide a source for energy, fuels for transport and chemicals for everyday items. However, adverse effects of decades of hydrocarbons production are increasingly impacting society and the environment. Production-driven reduction in reservoir pore pressure leads to a poro-elastic response of the reservoir, and in many occasions to time-dependent compaction (creep) of the reservoir. In turn, reservoir compaction may lead to surface subsidence and could potentially result in induced (micro)seismicity. To predict and mitigate the impact of fluid extraction, we need to understand production-driven reservoir compaction in highly porous siliciclastic rocks and explore potential mitigation strategies, for example, by using compaction-inhibiting injection fluids. As a first step, we investigate the effect of chemical environment on the compaction behaviour of sand aggregates, comparable to poorly consolidated, highly porous sandstones. The sand samples consist of loose aggregates of Beaujean quartz sand, sieved into a grainsize fraction of 180-212 µm. Uniaxial compaction experiments are performed at an axial stress of 35 MPa and temperature of 80°C, mimicking conditions of reservoirs buried at three kilometres depth. The chemical environment during creep is either vacuum-dry or CO2-dry, or fluid-saturated, with fluids consisting of distilled water, acid solution (CO2-saturated water), alkaline solution (pH 9), aluminium solution (pH 3) and solution with surfactants (i.e., AMP). Preliminary results show that compaction of quartz sand aggregates is promoted in a wet environment compared to a dry environment. It is inferred that deformation is controlled by subcritical crack growth when dry and stress corrosion cracking when wet, both resulting in grain failure and subsequent grain rearrangement. Fluids inhibiting these processes, have the potential to inhibit aggregate compaction.

Cense Explosion Test Program. Report 1. Cense 1. Explosions in Sandstone

Science.gov (United States)

1977-09-01

series, "Analysis and Summary of CENSE Data." 10 * _ CHAPTER 2 APPROACH 2.1 DESCRIPTION OF TEST SITE An exposed outcrop of Kayenta sandstone with 180...ft/s seismic velocity previously determined (References 12-14) for the unweathered upper zone of the Kayenta sandstone. 16 I The P-wave propagation...Propagation along the horizontal radial was 8400 ft/s. The seismic velocity pre- viously determined for Kayenta sandstone in this area was 7500 ft/s

Brief analysis on relationship between red beds and sandstone-type uranium ore-formation

International Nuclear Information System (INIS)

Ji Zengxian

2006-01-01

Red beds are sandy gravel beds deposited under the arid and hot climates and correspondent to the oxidation environment of continental basins. As an exogenetic epigenetic uranium deposit, the formation of the sandstone-type uranium deposit needs a large chronologic gap between the diagenesis and the subsequent uranium metallogenesis of the ore-hosting target layer with a sedimentary discontinuity and an alternative humid-arid climate. Red beds are the product of this time. The evolutionary times of red beds are in accordance with the formation of the sandstone-type uranium deposit. Both domestic and abroad researches indicate that each times evolution of a red bed might be associated with uranium ore-formation in one or more sandstone layers in the region. In China, red beds are developed in many geologic periods, but sandstone-type uranium mineralization occurs mostly in Mesozoic-Cenozoic. Taking five known sandstone-type uranium deposits as examples, the author makes a primary analysis on the relationship between red beds and the subsequent sandstone-type uranium mineralization. It is suggested that the deposition of red beds and sandstone-type uranium metallogenesis are of 'cogenesis and coexistence' and that the deposition of red beds and its evolutionary times can be regarded as the prerequisites to judge the potential of sandstone-type uranium mineralization in a Mesozoic-Cenozoic sedimentary basin. (authors)

System-wide significance of predation on juvenile salmonids in Columbia and Snake River reservoirs and evaluation of predation control measures. Annual report 1993

International Nuclear Information System (INIS)

Gadomski, D.M.; Poe, T.P.

1994-01-01

This project had three major goals. The first was to assist the Oregon Department of Fish and Wildlife with predation indexing as part of an effort to estimate the relative magnitude of juvenile salmonid losses to northern squawfish Ptychocheilus oregonensis in reservoirs throughout the Columbia River Basin. The second goal was to evaluate the northern squawfish control program and test critical assumptions about mid-reservoir predation processes. The final goal was to determine mechanisms underlying northern squawfish recruitment and factors affecting year-class strength

Mechanical Weakening during Fluid Injection in Critically Stressed Sandstones with Acoustic Monitoring

Science.gov (United States)

David, C.; Dautriat, J. D.; Sarout, J.; Macault, R.; Bertauld, D.

2014-12-01

Water weakening is a well-known phenomenon which can lead to subsidence during the production of hydrocarbon reservoirs. The example of the Ekofisk oil field in the North Sea has been well documented for years. In order to assess water weakening effects in reservoir rocks, previous studies have focused on changes in the failure envelopes derived from mechanical tests conducted on rocks saturated either with water or with inert fluids. However, little attention has been paid so far on the mechanical behaviour during the fluid injection stage, like in enhanced oil recovery operations. We studied the effect of fluid injection on the mechanical behaviour of Sherwood sandstone, a weakly-consolidated sandstone sampled at Ladram Bay in UK. In order to highlight possible weakening effects, water and inert oil have been injected into critically-loaded samples to assess their effect on strength and elastic properties and to derive the acoustic signature of the saturation front for each fluid. The specimens were instrumented with 16 ultrasonic P-wave transducers for both passive and active acoustic monitoring during fluid injection and loading. After conducting standard triaxial tests on three samples saturated with air, water and oil respectively, mechanical creep tests were conducted on dry samples loaded at 80% of the compressive strength of the dry rock. While these conditions are kept constant, a fluid is injected at the bottom end of the sample with a low back pressure (0.5 MPa) to minimize effective stress variations during injection. Both water and oil were used as the injected pore fluid in two experiments. As soon as the fluids start to flow into the samples, creep is taking place with a much higher strain rate for water injection compared to oil injection. A transition from secondary creep to tertiary creep is observed in the water injection test whereas in the oil injection test no significant creep acceleration is observed after one pore volume of oil was

Sandstone landforms shaped by negative feedback between stress and erosion

Czech Academy of Sciences Publication Activity Database

Bruthans, J.; Soukup, J.; Vaculíková, J.; Filippi, Michal; Schweigstillová, Jana; Mayo, A. L.; Mašín, D.; Kletetschka, Günther; Řihošek, J.

2014-01-01

Roč. 7, č. 8 (2014), s. 597-601 ISSN 1752-0894 R&D Projects: GA ČR GA13-28040S Institutional support: RVO:67985831 ; RVO:67985891 Keywords : sandstone * sandstone landsforms * stress * erosion Subject RIV: DB - Geology ; Mineralogy Impact factor: 11.740, year: 2014

Characterizing flow pathways in a sandstone aquifer: Tectonic vs sedimentary heterogeneities

Science.gov (United States)

Medici, G.; West, L. J.; Mountney, N. P.

2016-11-01

Sandstone aquifers are commonly assumed to represent porous media characterized by a permeable matrix. However, such aquifers may be heavy fractured when rock properties and timing of deformation favour brittle failure and crack opening. In many aquifer types, fractures associated with faults, bedding planes and stratabound joints represent preferential pathways for fluids and contaminants. In this paper, well test and outcrop-scale studies reveal how strongly lithified siliciclastic rocks may be entirely dominated by fracture flow at shallow depths (≤ 180 m), similar to limestone and crystalline aquifers. However, sedimentary heterogeneities can primarily control fluid flow where fracture apertures are reduced by overburden pressures or mineral infills at greater depths. The Triassic St Bees Sandstone Formation (UK) of the East Irish Sea Basin represents an optimum example for study of the influence of both sedimentary and tectonic aquifer heterogeneities in a strongly lithified sandstone aquifer-type. This fluvial sedimentary succession accumulated in rapidly subsiding basins, which typically favours preservation of complete depositional cycles including fine grained layers (mudstone and silty sandstone) interbedded in sandstone fluvial channels. Additionally, vertical joints in the St Bees Sandstone Formation form a pervasive stratabound system whereby joints terminate at bedding discontinuities. Additionally, normal faults are present through the succession showing particular development of open-fractures. Here, the shallow aquifer (depth ≤ 180 m) was characterized using hydro-geophysics. Fluid temperature, conductivity and flow-velocity logs record inflows and outflows from normal faults, as well as from pervasive bed-parallel fractures. Quantitative flow logging analyses in boreholes that cut fault planes indicate that zones of fault-related open fractures characterize 50% of water flow. The remaining flow component is dominated by bed-parallel fractures

Electrokinetic desalination of sandstones for NaCl removal

DEFF Research Database (Denmark)

Ottosen, Lisbeth M.; Christensen, Iben V.

2012-01-01

of reliable methods to remove the damaging salts in order to stop the decay. Electrokinetic desalination of fired clay bricks have previously shown efficient in laboratory scale and in the present work the method is tested for desalination of Cotta and Posta sandstones, which both have lower porosity than...... each stone, but electroosmosis in the poultices may have caused suction/pressure over the interface between stone and poultice causing the differences in poultice water content. The transport numbers for Cl− and Na+ differed in the two stones and were highest in the most porous Cotta sandstone in spite...... of similar high pore water concentrations and the same applied electric current. The hypotheses is that a layered structure of the sandstones could be the cause for this, as the electric current may preferentially flow in certain paths through the stone, which are thus desalinated first. After...

The Jurassic of Denmark and Greenland: Sedimentology and sequence stratigraphy of paralic and shallow marine Upper Jurassic sandstones in the northern Danish Central Graben

Directory of Open Access Journals (Sweden)

Johannessen, Peter N.

2003-10-01

Full Text Available Paralic and shallow marine sandstones were deposited in the Danish Central Graben during Late Jurassic rifting when half-grabens were developed and the overall eustatic sea level rose. During the Kimmeridgian, an extensive plateau area consisting of the Heno Plateau and the Gertrud Plateau was situated between two highs, the Mandal High to the north, and the combined Inge and Mads Highs to the west. These highs were land areas situated on either side of the plateaus and supplied sand to the Gertrud and Heno Plateaus. Two graben areas, the Feda and Tail End Grabens, flanked the plateau area to the west and east, respectively. The regressive–ransgressive succession consists of intensely bioturbated shoreface sandstones, 25–75 m thick. Two widespread unconformities (SB1, SB2 are recognised on the plateaus, forming the base of sequence 1 and sequence 2, respectively. These unconformities were created by a fall in relative sea level during which rivers may have eroded older shoreface sands and transported sediment across the Heno andGertrud Plateaus, resulting in the accumulation of shoreface sandstones farther out in the Feda and Tail End Grabens, on the south-east Heno Plateau and in the Salt Dome Province. Duringsubsequent transgression, fluvial sediments were reworked by high-energy shoreface processes on the Heno and Gertrud Plateaus, leaving only a lag of granules and pebbles on the marine transgressive surfaces of erosion (MTSE1, MTSE2.The sequence boundary SB1 can be traced to the south-east Heno Plateau and the Salt Dome Province, where it is marked by sharp-based shoreface sandstones. During low sea level, erosion occurred in the southern part of the Feda Graben, which formed part of the Gertrud and Heno Plateaus, and sedimentation occurred in the Norwegian part of the Feda Graben farther to the north. During subsequent transgression, the southern part of the Feda Graben began to subside, and a succession of backstepping back

On the migration of uranium isotopes in sandstone aquifers

International Nuclear Information System (INIS)

Froehlich, K.; Gellermann, R.

1982-01-01

Measurements of natural 238 U and 234 U activity in groundwater of sandstone aquifers have been used to study the migration of these uranium isotopes. Regarding the uranium exchange between liquid phase and rock surface during migration, two different models were applied for evaluating the experimental results. Values of corresponding parameters (retardation factor K, removal rate R) reflecting different behaviour concerning this exchange were determined. For example, the values obtained for 238 U in a Triassic sandstone aquifer of the GDR are K = 8.6 x 10 6 and R = 1.3 x 10 -3 a -1 , respectively. It was found that, under the conditions of the sandstone aquifer concerned, the removal rate model is better suited for calculating uranium-isotope migration in groundwater. (author)

Discussion on distribution characteristics of calcareous sandstone in Shihongtan uranium deposit and its genesis

International Nuclear Information System (INIS)

Zhu Huanqiao; Qiao Haiming; Jia Heng; Xu Gaozhong

2007-01-01

Based on the observation and statistics on the calcareous sandstone in the ore host layer in Shihongtan uranium deposit, this paper finds that the calcareous sandstone occurs on and off near the top or wash surface of the sandbody as beads-strings lens along the layer and concentrates in the area where the ore bodies are rich. In lithology, the calcareous sandstone is of coarse grain and fairly well sorted. According to the analysis on the lithogeochemical features and the carbon and oxygen isotopes of calcareous sandstones, it is realized that there some genetic relation between the formation of calcareous sandstone and uranium mineralization in the oxidation-deoxidation transitional belt, that is the precipitation and enrichment of uranium is accompanied by the deposition of carbonate and formation of calcareous sandstone. (authors)

An analytical comparison of two commercial consolidating products applied to eocene sandstones from 16th and 19th century monuments in San Sehastián, northern Spain

Directory of Open Access Journals (Sweden)

García-Garmilla, F.

2002-06-01

Full Text Available The conservation of buildings in the Basque Country made of Eocene sandstone is somewhat problematical, because this type of rock is relatively unstable. This instability is due to the variable content of carbonate cement (0-28% and the presence of K-feldspar grains (1-13% which appear to have been dissolved by both diagenetic and environmental processes. We have compared the results of the application of two commercial consolidating products: Sicof SM 296 (product A and Consistone FS-hA (product B, both ethylsilicates, on Eocene sandstones of the Oquendo Admiral House (16th century and the Gipuzkoa Provincial Government Palace (19th century, which are both located in the city of San Sebastián (Province of Gipuzkoa, Basque Country, Northern Spain. On the basis of different chemical and physical laboratory tests, together with Scanning Electron Microscopy (SEM analysis, product A seems to be more efficient in consolidating such Eocene sandstone materials, since it penetrates into the first 8 mm of the rock, occupies very homogeneously even the smallest pore spaces and leaves a certain degree of remaining porosity which allows ventilation of the rock. In contrast, product B seems to be more appropriate for larger pore-sized rocks, because it only penetrates into the first 3 mm of the Eocene sandstone samples due to the thin pores of the matter. Our results demonstrate that the suitability of a commercial product depends not only on its own chemical composition, but also on the textural and lithological features of the rock material upon which it is to be applied.

La conservación de los edificios del País Vasco construidos con areniscas del Eoceno es problemática porque este tipo de roca es relativamente inestable debido a su contenido variable en cemento carbonatado (0-28% y a la presencia de granos de feldespato potásico (1-13% disueltos tanto por procesos diagenéticos como ambientales. Hemos aplicado dos consolidantes comerciales

Fluid circulation and diagenesis of carbonated and sandstone reservoirs in the fronts and fore-lands of folded chains: the Salt Range case - Poswar (Pakistan); Circulation des fluides et diagenese des reservoirs carbonates et greseux dans les fronts de chaines plissees et leur avant pays: le cas du Salt Range - Poswar (Pakistan)

Energy Technology Data Exchange (ETDEWEB)

Benchilla, L.

2003-05-01

The Salt Range-Poswar Province is located in the western foothills of the Himalayas, in northern Pakistan. It extends over 170 km from the Main Boundary Thrust (MBT) in the north to the Salt Range in the south. The Salt Range itself is dominantly an ENE-trending structure, but it comprises also a NNW-trending lateral ramp which connects to the west with the Surghar Range. The Salt Range constitutes the frontal part of a detached allochthonous thrust sheet. The sedimentary cover is indeed entirely detached from its substratum along Infracambrian salt horizons. Palaeozoic to Eocene platform series are well exposed in the hanging wall, whereas Neogene molasse has been extensively under-thrust in the footwall of this large over-thrust. The North Potwar Basin is bordered by the Khari-Murat Ridge and coeval back-thrusts in the south, by the northern flank of the Soan syncline in the southeast, and by the MBT in the north. In addition to Neogene outcrops, it also comprises a number of surface anticlines and thrust fronts along which the Eocene platform carbonates are exposed. The Datta Formation is the main Jurassic oil reservoir in the Potwar Basin. It is a fluvio-deltaic deposit which comprises large porous and permeable channels associated to many-calcareous interbeds. The formations crop out well in both the Nammal and Chichali Gorges. The oil field of Toot, located in the western part of the basin, is producing from this reservoir. The petrographic observations show that diagenesis occurred mainly early and was controlled by the fluvio-deltaic environment. (author)

A complex investigation of building sandstones from Saxony (Germany)

International Nuclear Information System (INIS)

Goetze, Jens; Siedel, Heiner

2007-01-01

The present paper provides a methodology for the investigation and characterization of building sandstones. This analytical scheme was designed for distinguishing mature arenites, which in general show very similar properties and are difficult to distinguish. This is shown for Cretaceous sandstones from various occurrences in Saxony (Germany), which have been used for centuries as building materials. The procedure is mainly based on the combination of macroscopic rock description, thin section polarizing microscopy (phase composition, texture, grain-size distribution) and cathodoluminescence (CL) microscopy (quartz types, feldspar and kaolinite content) coupled with image analysis, scanning electron microscopy (accessories, pore cement, diagenetic grain surface features), and analysis of pore space data. Sometimes, additional data from X-ray diffraction or chemical analyses (major and trace elements) can be used. Especially in the case of quartz rich arenites, CL is a powerful tool for provenance analysis. The detailed analysis of sandstone material in most cases allows us to assign historically used building material to a specific sandstone occurrence. These results are important for both interpreting the weathering behaviour of the building material and the conservation, reconstruction and stone replacement of historical monuments

Effects of Pisha sandstone content on solute transport in a sandy soil.

Science.gov (United States)

Zhen, Qing; Zheng, Jiyong; He, Honghua; Han, Fengpeng; Zhang, Xingchang

2016-02-01

In sandy soil, water, nutrients and even pollutants are easily leaching to deeper layers. The objective of this study was to assess the effects of Pisha sandstone on soil solute transport in a sandy soil. The miscible displacement technique was used to obtain breakthrough curves (BTCs) of Br(-) as an inert non-adsorbed tracer and Na(+) as an adsorbed tracer. The incorporation of Pisha sandstone into sandy soil was able to prevent the early breakthrough of both tracers by decreasing the saturated hydraulic conductivity compared to the controlled sandy soil column, and the impeding effects increased with Pisha sandstone content. The BTCs of Br(-) were accurately described by both the convection-dispersion equation (CDE) and the two-region model (T-R), and the T-R model fitted the experimental data slightly better than the CDE. The two-site nonequilibrium model (T-S) accurately fit the Na(+) transport data. Pisha sandstone impeded the breakthrough of Na(+) not only by decreasing the saturated hydraulic conductivity but also by increasing the adsorption capacity of the soil. The measured CEC values of Pisha sandstone were up to 11 times larger than those of the sandy soil. The retardation factors (R) determined by the T-S model increased with increasing Pisha sandstone content, and the partition coefficient (K(d)) showed a similar trend to R. According to the results of this study, Pisha sandstone can successfully impede solute transport in a sandy soil column. Copyright © 2015 Elsevier Ltd. All rights reserved.

Modeling surface energy fluxes and thermal dynamics of a seasonally ice-covered hydroelectric reservoir.

Science.gov (United States)

Wang, Weifeng; Roulet, Nigel T; Strachan, Ian B; Tremblay, Alain

2016-04-15

The thermal dynamics of human created northern reservoirs (e.g., water temperatures and ice cover dynamics) influence carbon processing and air-water gas exchange. Here, we developed a process-based one-dimensional model (Snow, Ice, WAater, and Sediment: SIWAS) to simulate a full year's surface energy fluxes and thermal dynamics for a moderately large (>500km(2)) boreal hydroelectric reservoir in northern Quebec, Canada. There is a lack of climate and weather data for most of the Canadian boreal so we designed SIWAS with a minimum of inputs and with a daily time step. The modeled surface energy fluxes were consistent with six years of observations from eddy covariance measurements taken in the middle of the reservoir. The simulated water temperature profiles agreed well with observations from over 100 sites across the reservoir. The model successfully captured the observed annual trend of ice cover timing, although the model overestimated the length of ice cover period (15days). Sensitivity analysis revealed that air temperature significantly affects the ice cover duration, water and sediment temperatures, but that dissolved organic carbon concentrations have little effect on the heat fluxes, and water and sediment temperatures. We conclude that the SIWAS model is capable of simulating surface energy fluxes and thermal dynamics for boreal reservoirs in regions where high temporal resolution climate data are not available. SIWAS is suitable for integration into biogeochemical models for simulating a reservoir's carbon cycle. Copyright © 2016 Elsevier B.V. All rights reserved.

Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting sandstone layer at sandstone-type uranium deposit

International Nuclear Information System (INIS)

Zhao Xigang; Wu Hanning; Bai Guanjun; Zhu Huanqiao; Jia Heng

2006-01-01

Geophysical signature recognition of aquifuge and relatively impermeable interbed in ore-hosting aquifer has been carried out a Shihongtan uranium deposit by using comprehensive logging data. The spatial distribution of above aquifuge and impermeable interbed is discussed, and the relation of these layers to sandstone-type uranium deposit, and their impact to in-situ leach mining technology are discussed. It is suggested that the aquifuge and relatively impermeable interbed bring about significant effect to the formation of interlayer oxidation zone sandstone-type uranium deposit, as well as to in-situ leach mining of the deposit. (authors)

On the CO2 Wettability of Reservoir Rocks: Addressing Conflicting Information

Science.gov (United States)

Garing, C.; Wang, S.; Tokunaga, T. K.; Wan, J.; Benson, S. M.

2017-12-01

Conventional wisdom is that siliclastic rocks are strongly water wet for the CO2-brine system, leading to high irreducible water saturation, moderate residual gas trapping and implying that tight rocks provide efficient seals for buoyant CO2. If the wetting properties become intermediate or CO2 wet, the conclusions regarding CO2 flow and trapping could be very different. Addressing the CO2 wettability of seal and reservoir rocks is therefore essential to predict CO2 storage in geologic formation. Although a substantial amount of work has been dedicated to the topic, contact angle data show a large variability and experiments on plates, micromodels and cores report conflicting results regarding the influence of supercritical CO2 (scCO2) exposure on wetting properties: whereas some experimental studies suggest dewetting upon reaction with scCO2, some others observe no wettability alteration under reservoir scCO2 conditions. After reviewing evidences for and against wettability changes associated with scCO2, we discuss potential causes for differences in experimental results. They include the presence of organic matter and impact of sample treatment, the type of media (non consolidated versus real rock), experimental time and exposure to scCO2, and difference in measurement system (porous plate versus stationary fluid method). In order to address these points, new scCO2/brine drainage-imbibition experiments were conducted on a same Berea sandstone rock core, first untreated, then fired and finally exposed to scCO2 for three weeks, using the stationary fluid method. The results are compared to similar experiments performed on quartz sands, untreated and then baked, using the porous plate method. In addition, a comparative experiment using the same Idaho gray sandstone rock core was performed with both the porous plate and the stationary fluid methods to investigate possible method-dependent results.

Geology of the Ulugh Muztagh area, northern Tibet

International Nuclear Information System (INIS)

Burchfiel, B.C.; Molnar, P.

1989-01-01

Within the Ulugh Muztagh area, north central Tibet, an east-west-trending ophiolitic melange marks a suture that apparently was formed during a late Triassic or slightly younger collision between a continental fragment to the south and the rest of Asia. The southern continental fragment carries a thick sequence of upper Triassic sandstone, but the contact between the sandstone and the ophiolitic melange is covered by a younger redbed sequence of unknown age. A suite of 2-mica, tourmaline-bearing leucogranite plutons and dikes intruded the Triassic sandstone at shallow crustal levels 10.5 to 8.4 Ma. These rocks range from granite to tonalite in composition, are geochemically very similar to slightly older High Himalayan leucogranite and are interpreted to have been derived by the partial melting of crustal material. We interpret this to mean that crustal thickening began in this part of the Tibetan plateau at least by 10.5 Ma. Welded rhyolitic tuff rests on a conglomerate that consists of abundant debris from the Ulugh Muztagh intrusive rocks and has yielded Ar/Ar ages of about 4 Ma. The tuffs are geochemically identical to the intrusive rocks suggesting that crustal thickening may have continued to 4 Ma. Crustal thickening probably occurred by distributed crustal shortening similar to shortening now occurring north of Ulugh Muztagh along the northern margin of the Tibetan Plateau. (orig.)

Application of magnetic techniques to lateral hydrocarbon migration - Lower Tertiary reservoir systems, UK North Sea

Science.gov (United States)

Badejo, S. A.; Muxworthy, A. R.; Fraser, A.

2017-12-01

Pyrolysis experiments show that magnetic minerals can be produced inorganically during oil formation in the `oil-kitchen'. Here we try to identify a magnetic proxy that can be used to trace hydrocarbon migration pathways by determining the morphology, abundance, mineralogy and size of the magnetic minerals present in reservoirs. We address this by examining the Tay formation in the Western Central Graben in the North Sea. The Tertiary sandstones are undeformed and laterally continuous in the form of an east-west trending channel, facilitating long distance updip migration of oil and gas to the west. We have collected 179 samples from 20 oil-stained wells and 15 samples from three dry wells from the British Geological Survey Core Repository. Samples were selected based on geological observations (water-wet sandstone, oil-stained sandstone, siltstones and shale). The magnetic properties of the samples were determined using room-temperature measurements on a Vibrating Sample Magnetometer (VSM), low-temperature (0-300K) measurements on a Magnetic Property Measurement System (MPMS) and high-temperature (300-973K) measurements on a Kappabridge susceptibility meter. We identified magnetite, pyrrhotite, pyrite and siderite in the samples. An increasing presence of ferrimagnetic iron sulphides is noticed along the known hydrocarbon migration pathway. Our initial results suggest mineralogy coupled with changes in grain size are possible proxies for hydrocarbon migration.

Experimental Investigation on the Behavior of Supercritical CO2 during Reservoir Depressurization.

Science.gov (United States)

Li, Rong; Jiang, Peixue; He, Di; Chen, Xue; Xu, Ruina

2017-08-01

CO 2 sequestration in saline aquifers is a promising way to address climate change. However, the pressure of the sequestration reservoir may decrease in practice, which induces CO 2 exsolution and expansion in the reservoir. In this study, we conducted a core-scale experimental investigation on the depressurization of CO 2 -containing sandstone using NMR equipment. Three different series of experiments were designed to investigate the influence of the depressurization rate and the initial CO2 states on the dynamics of different trapping mechanisms. The pressure range of the depressurization was from 10.5 to 4.0 MPa, which covered the supercritical and gaseous states of the CO 2 (named as CO 2 (sc) and CO 2 (g), respectively). It was found that when the aqueous phase saturated initially, the exsolution behavior strongly depended on the depressurization rate. When the CO 2 and aqueous phase coexisting initially, the expansion of the CO 2 (sc/g) contributed to the incremental CO 2 saturation in the core only when the CO 2 occurred as residually trapped. It indicates that the reservoir depressurization has the possibility to convert the solubility trapping to the residual trapping phase, and/or convert the residual trapping to mobile CO 2 .

Well pattern optimization in a low permeability sandstone reservoir: a case study from Erlian Basin in China

Science.gov (United States)

Wang, Xia; Fu, Lixia; Yan, Aihua; Guo, Fajun; Wu, Cong; Chen, Hong; Wang, Xinying; Lu, Ming

2018-02-01

Study on optimization of development well patterns is the core content of oilfield development and is a prerequisite for rational and effective development of oilfield. The study on well pattern optimization mainly includes types of well patterns and density of well patterns. This paper takes the Aer-3 fault block as an example. Firstly, models were built for diamond-shaped inverted 9-spot patterns, rectangular 5-spot patterns, square inverted 9-spot patterns and inverted 7-spot patterns under the same well pattern density to correlate the effect of different well patterns on development; secondly, comprehensive analysis was conducted to well pattern density in terms of economy and technology using such methods as oil reservoir engineering, numerical simulation, economic limits and economic rationality. Finally, the development mode of vertical well + horizontal well was presented according to the characteristics of oil reservoirs in some well blocks, which has realized efficient development of this fault block.

Temperature effect on microstructure and P-wave propagation in Linyi sandstone

International Nuclear Information System (INIS)

Sun, Hui; Sun, Qiang; Deng, Wenni; Zhang, Weiqiang; Lü, Chao

2017-01-01

Highlights: • Mass loss rate, P-wave velocity change rate and damage factor increase exponentially as temperatures rise. • The damage threshold temperature of sandstone samples is 300 °C and limit temperature is 900 °C. • P-wave velocity change rate of sandstone exhibits excellent linearity with mass loss rate. • Damage factor can be well expressed by mass loss rate. - Abstract: In order to study the effect of high temperature on the sandstone, scanning electron microscope (SEM) experiments and primary wave (P-wave) velocity tests have been carried out on sandstone specimens heated to different temperature. The results showed that: (1) the mass loss rate increases exponentially with the increase of temperature and reaches 2.97% at 900 °C; (2) the P-wave velocity change rate increases exponentially with the increase of temperature while there is some fluctuation before 500 °C; (3) the damage threshold temperature of sandstone samples is 300 °C and the limit temperature is 900 °C; (4) there is a good linear relationship between the mass loss rate and the P-wave velocity change rate, and the correlation coefficient (R) of the fitting line is 0.989; (5) the damage caused by high temperature can be reflected better by the mass loss rate than P-wave velocity change rate. The results obtained in this paper will be good for predicting the properties of sandstone when exposed to high temperature.

Improving Oil Recovery (IOR) with Polymer Flooding in a Heavy-Oil River-Channel Sandstone Reservoir

OpenAIRE

Lu, Hongjiang

2009-01-01

Most of the old oil fields in China have reached high water cut stage, in order to meet the booming energy demanding, oil production rate must be kept in the near future with corresponding IOR (Improving Oil Recovery) methods. Z106 oilfield lies in Shengli Oilfields Area at the Yellow River delta. It was put into development in 1988. Since the oil belongs to heavy oil, the oil-water mobility ratio is so unfavourable that water cut increases very quickly. Especially for reservoir Ng21, the san...

Desalination of salt damaged Obernkirchen sandstone by an applied DC field

DEFF Research Database (Denmark)

Matyščák, Ondřej; Ottosen, Lisbeth M.; Rörig-Dalgaard, Inge

2014-01-01

Soluble salts are considered as one of the most common causes for decay of building materials. In the present work, an electrokinetic method for desalination of sandstones from a historic warehouse was tested. The sandstones claddings were removed from the warehouse during a renovation action...... in the stones, i.e. the present investigation faces more challenges relevant to a real desalination action. Experiments were conducted with two Obernkirchen sandstones from the same warehouse, but with different levels of salt concentrations and porosity. The investigation includes removal of the most common...... salts: chlorides, nitrates, sulphates. In the experimental setup the electrodes were placed in a clay poultice: a mixture of kaolinite, calcite and distilled water. An electric direct current (DC) field was applied to the sandstone.By applying 2mA for 5–11days it was possible to reduce the chloride...

Characteristics and model of sandstone type uranium deposit in south of Songliao basin

International Nuclear Information System (INIS)

Yu Wenbin; Yu Zhenqing

2010-01-01

Through analyzing the uranium deposit tectonic environment, upper cretaceous sequence stratigraphy, depositional system, evolutionary characteristics of sand bodies, the effect of subsequent transformation and the characteristic of uranium deposit, the sandstone type uranium deposit in southern basin is different from typical interlayer oxidation zone sandstone type uranium deposit. The formation and evolution of sandstone-type uranium deposit are controlled by structure fensters; the favorable sedimentary facies type is braided river facies, and the ore body is braided river sand body. The size of uranium deposits is controlled by the local oxidation zone with the characteristics of sandstone type uranium deposit in partial oxidation zone. Uranium ore bodies which distribute in the roof wings of structure fenstes, and occur in gray layers between the upper and lower oxidation zone, showing tabular, and the plate of uranium ore body is controlled by the local oxidation zone. Based on the geological features of sandstone-type uranium deposits, the metallogenic model of local oxidation zones sandstone-type uranium deposits has been set up in the south of Songliao Baisn. (authors)

3-D description of fracture surfaces and stress-sensitivity analysis for naturally fractured reservoirs

Energy Technology Data Exchange (ETDEWEB)

Zhang, S.Q.; Jioa, D.; Meng, Y.F.; Fan, Y.

1997-08-01

Three kinds of reservoir cores (limestone, sandstone, and shale with natural fractures) were used to study the effect of morphology of fracture surfaces on stress sensitivity. The cores, obtained from the reservoirs with depths of 2170 to 2300 m, have fractures which are mated on a large scale, but unmated on a fine scale. A specially designed photoelectric scanner with a computer was used to describe the topography of the fracture surfaces. Then, theoretical analysis of the fracture closure was carried out based on the fracture topography generated. The scanning results show that the asperity has almost normal distributions for all three types of samples. For the tested samples, the fracture closure predicted by the elastic-contact theory is different from the laboratory measurements because plastic deformation of the aspirates plays an important role under the testing range of normal stresses. In this work, the traditionally used elastic-contact theory has been modified to better predict the stress sensitivity of reservoir fractures. Analysis shows that the standard deviation of the probability density function of asperity distribution has a great effect on the fracture closure rate.

Gamma ray spectrometry logs as a hydrocarbon indicator for clastic reservoir rocks in Egypt

International Nuclear Information System (INIS)

Al-Alfy, I.M.; Nabih, M.A.; Eysa, E.A.

2013-01-01

Petroleum oil is an important source for the energy in the world. The Gulf of Suez, Nile Delta and South Valley are important regions for studying hydrocarbon potential in Egypt. A thorium normalization technique was applied on the sandstone reservoirs in the three regions to determine the hydrocarbon potentialities zones using the three spectrometric radioactive gamma ray-logs (eU, eTh and K% logs). The conventional well logs (gamma-ray, deep resistivity, shallow resistivity, neutron, density and sonic logs) are analyzed to determine the net pay zones in these wells. Indices derived from thorium normalized spectral logs indicate the hydrocarbon zones in petroleum reservoirs. The results of this technique in the three regions (Gulf of Suez, Nile Delta and South Valley) are in agreement with the results of the conventional well log analyses by ratios of 82%, 78% and 71% respectively. - Highlights: ► The positive DRAD values indicate the hydrocarbon zones in petroleum reservoirs. ► Thorium normalization was applied to determine the hydrocarbon potentialities. ► The conventional well logs are analyzed to determine the net pay zones in wells. ► Determining hydrocarbon potentialities zones using spectrometric gamma-ray logs

An analytical framework for extracting hydrological information from time series of small reservoirs in a semi-arid region

Science.gov (United States)

Annor, Frank; van de Giesen, Nick; Bogaard, Thom; Eilander, Dirk

2013-04-01

Small water reservoirs for water resources management have as important socio-economic advantage that they bring water close to villages and households. This proximity allows for many water uses in addition to irrigation, such as fisheries, household water, building materials (loam, reeds), tourism and recreation, and cattle watering. These positive aspects are offset by the relatively large evaporative losses in comparison to larger reservoirs, although, it is not exactly known how large these losses are. For decision makers, investors and donors, the decision to construct a small reservoir should be multifactored; and based on economic, socio-cultural and environmental factors. For the latter, getting the water balance and the energy budget of small reservoirs right is key for any environmental impact analyses. For Northern Ghana, the relation between volume of a small reservoir and its' surface area has been established in a robust equation as: Volume = 0.00857Area1.4367 with the surface area explaining more than 95% of the variation in water volume of the reservoirs. This allows the use of remote sensing observations for estimating water volume of small reservoirs in northern Ghana. Hydrological analyses of time series of small reservoir areas comprises estimates of evaporation fluxes and cumulative surface runoff curves. Once the reservoirs are full, spillage will occur and volumes and surface areas remain stable at their maximum extents. This implies that the time series of reservoir surface area contains information concerning the on-set of downstream surface runoff. This on-set does not coincide with the on-set of the rainy season but largely depends on the distribution of rainfall events and storage capacity in the subsurface. The main requirement for this analysis is that the reservoir has negligible seepage losses or water influx from the underlying subsurface. In our research, we carried out a time series analysis of surface area extent for about 45

Reservoir attributes of a hydrocarbon-prone sandstone complex: case of the Pab Formation (Late Cretaceous) of Southwest Pakistan

DEFF Research Database (Denmark)

Umar, Muhammad; Khan, Abdul Salam; Kelling, Gilbert

2016-01-01

Links between the architectural elements of major sand bodies and reservoir attributes have been explored in a field study of the hydrocarbon-yielding Late Cretaceous Pab Formation of southwest Pakistan. The lithofacies and facies associations represented in the Pab Formation are the main...... determinants of its reservoir properties. Thus, thick, vertically connected and laterally continuous sand packets have moderate-to-high mean porosities (10–13 %) in fluviodeltaic, shoreface, shelf delta, submarine channel, and fan-lobe facies associations while deeper shelf and basin floor sand bodies yield...... significantly lower porosities (4–6 %). Overall, in the Pab arenites, porosity values increase with increasing grain size and better sorting. The varying sand-shale ratios encountered in different sectors of the Pab outcrop are also petrophysically important: Sequences displaying high ratios yield higher bulk...

Earthquakes and depleted gas reservoirs: which comes first?

Science.gov (United States)

Mucciarelli, M.; Donda, F.; Valensise, G.

2015-10-01

While scientists are paying increasing attention to the seismicity potentially induced by hydrocarbon exploitation, so far, little is known about the reverse problem, i.e. the impact of active faulting and earthquakes on hydrocarbon reservoirs. The 20 and 29 May 2012 earthquakes in Emilia, northern Italy (Mw 6.1 and 6.0), raised concerns among the public for being possibly human-induced, but also shed light on the possible use of gas wells as a marker of the seismogenic potential of an active fold and thrust belt. We compared the location, depth and production history of 455 gas wells drilled along the Ferrara-Romagna arc, a large hydrocarbon reserve in the southeastern Po Plain (northern Italy), with the location of the inferred surface projection of the causative faults of the 2012 Emilia earthquakes and of two pre-instrumental damaging earthquakes. We found that these earthquake sources fall within a cluster of sterile wells, surrounded by productive wells at a few kilometres' distance. Since the geology of the productive and sterile areas is quite similar, we suggest that past earthquakes caused the loss of all natural gas from the potential reservoirs lying above their causative faults. To validate our hypothesis we performed two different statistical tests (binomial and Monte Carlo) on the relative distribution of productive and sterile wells, with respect to seismogenic faults. Our findings have important practical implications: (1) they may allow major seismogenic sources to be singled out within large active thrust systems; (2) they suggest that reservoirs hosted in smaller anticlines are more likely to be intact; and (3) they also suggest that in order to minimize the hazard of triggering significant earthquakes, all new gas storage facilities should use exploited reservoirs rather than sterile hydrocarbon traps or aquifers.

Potential human health risk by 234,238U and 210Po due to consumption of fish from the "Luis L. Leon" reservoir (Northern Mexico)

Science.gov (United States)

Luna-Porres, M. Y.; Rodríguez-Villa, M. A.; Herrera-Peraza, E.; Cabral-Lares, M.; Renteria-Villalobos, M.; Montero-Cabrera, M. E.

2014-07-01

The Conchos River is one of the most important in northern Mexico and the main surface waterway in the arid state of Chihuahua. The Luis L. Leon dam produces the Luis L. Leon Reservoir, which is the last major reservoir before the Conchos River enters the Rio Grande at the Texas-Chihuahua border. Activity concentrations (AC) of 234,238U and 210Po in fillet and liver of three stocked fish species (Lepomis cyanellus, Cyprinus carpio and Ictalurus furcatus), as well as in water from the Luis L. Leon reservoir were determined. 238U and 234U ACs in fillet samples showed values of 0.007-0.014 and 0.01-0.02 Bq kg-1 wet weight (ww), respectively. Liver samples for Lepomis cyanellus, Cyprinus carpio and Ictalurus furcatus species, present 210Po AC of 1.16-3.26 0.70-1.13 and 0.93-1.37 Bqṡkg-1 ww. The elemental Bioaccumulation Factor (BAF) for fish tissues respect to their concentrations in water was determined. Lepomis cyanellus species showed the highest BAF for total uranium in fillet, with value 1.5. The annual effective dose for uranium in adults by fish consumption in this work ranged from 4.46×10-3 to 3.68×10-2 μSvṡyear-1. The difference in concentrations of uranium in fillet among the studied species is likely primarily due to their differences in diet and habitat.

Gamma ray spectrometry logs as a hydrocarbon indicator for clastic reservoir rocks in Egypt.

Science.gov (United States)

Al-Alfy, I M; Nabih, M A; Eysa, E A

2013-03-01

Petroleum oil is an important source for the energy in the world. The Gulf of Suez, Nile Delta and South Valley are important regions for studying hydrocarbon potential in Egypt. A thorium normalization technique was applied on the sandstone reservoirs in the three regions to determine the hydrocarbon potentialities zones using the three spectrometric radioactive gamma ray-logs (eU, eTh and K% logs). The conventional well logs (gamma-ray, deep resistivity, shallow resistivity, neutron, density and sonic logs) are analyzed to determine the net pay zones in these wells. Indices derived from thorium normalized spectral logs indicate the hydrocarbon zones in petroleum reservoirs. The results of this technique in the three regions (Gulf of Suez, Nile Delta and South Valley) are in agreement with the results of the conventional well log analyses by ratios of 82%, 78% and 71% respectively. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Sediment problems in reservoirs. Control of sediment deposits

Energy Technology Data Exchange (ETDEWEB)

Jacobsen, Tom

1997-12-31

When a reservoir is formed on a river, sediment will deposit in the reservoir. Such processes are unfortunate, for instance, for the implementation of hydroelectric energy. This thesis studies the problem of reservoir sedimentation and discusses methods of removing the sediments. Various aspects of reservoir sedimentation are discussed. Anthropogenic impacts seem to greatly affect the erosion processes. Temporal distribution is uneven, mainly because of the very large flood events. A world map showing the Reservoir Capacity: Annual Sediment Inflow ratio for reservoirs with volume equal to 10% of annual inflow has been prepared. The map shows that sedimentation is severe in the western parts of North and South America, eastern, southern and northern Africa, parts of Australia and most of Asia. The development of medium-sized reservoirs is difficult, as they are too large for conventional flushing technique and too small to store the sediment that accumulates during their economic lifetime. A computer model, SSIIM, was used with good results in a case study of two flood drawdown trials in Lake Roxburg, New Zealand. Two techniques have been developed that permits controlled suction of sediment and water into a pipe: the Slotted Pipe Sediment Sluicer (SPSS) and the Saxophone Sediment Sluicer (SSS). The techniques exploit the inflow pattern in through a slot in a pipe. An equation describing this inflow pattern was derived and verified experimentally. The SPSS is fixed near the reservoir bed, and sediment that deposits on top of it is removed in the sluicing process. The SSS sluices sediment from the surface of the sediment deposits. Some technical and economic conditions affecting the economics of sediment removal from reservoirs have been identified and studied. 79 refs., 112 figs., 14 tabs.

CO2 geosequestration at the laboratory scale: Combined geophysical and hydromechanical assessment of weakly-cemented shallow Sleipner-like reservoirs

Science.gov (United States)

Falcon-Suarez, I.; North, L. J.; Best, A. I.

2017-12-01

To date, the most promising mitigation strategy for reducing global carbon emissions is Carbon Capture and Storage (CCS). The storage technology (i.e., CO2 geosequestration, CGS) consists of injecting CO2 into deep geological formations, specifically selected for such massive-scale storage. To guarantee the mechanical stability of the reservoir during and after injection, it is crucial to improve existing monitoring techniques for controlling CGS activities. We developed a comprehensive experimental program to investigate the integrity of the Sleipner CO2 storage site in the North Sea - the first commercial CCS project in history where 1 Mtn/y of CO2 has been injected since 1996. We assessed hydro-mechanical effects and the related geophysical signatures of three synthetic sandstones and samples from the Utsira Sand formation (main reservoir at Sleipner), at realistic pressure-temperature (PT) conditions and fluid compositions. Our experimental approach consists of brine-CO2 flow-through tests simulating variable inflation/depletion scenarios, performed in the CGS-rig (Fig. 1; Falcon-Suarez et al., 2017) at the National Oceanography Centre (NOC) in Southampton. The rig is designed for simultaneous monitoring of ultrasonic P- and S-wave velocities and attenuations, electrical resistivity, axial and radial strains, pore pressure and flow, during the co-injection of up to two fluids under controlled PT conditions. Our results show velocity-resistivity and seismic-geomechanical relations of practical importance for the distinction between pore pressure and pore fluid distribution during CGS activities. By combining geophysical and thermo-hydro-mechano-chemical coupled information, we can provide laboratory datasets that complement in situ seismic, geomechanical and electrical survey information, useful for the CO2 plume monitoring in Sleipner site and other shallow weakly-cemented sand CCS reservoirs. Falcon-Suarez, I., Marín-Moreno, H., Browning, F., Lichtschlag, A

Study on the enhancement of hydrocarbon recovery by characterization of the reservoir

Energy Technology Data Exchange (ETDEWEB)

Kwak, Young Hoon; Son, Jin Dam; Oh, Jae Ho [Korea Institute of Geology Mining and Materials, Taejon (Korea)] [and others

1998-12-01

Three year project is being carried out on the enhancement of hydrocarbon recovery by the reservoir characterization. This report describes the results of the second year's work. This project deals with characterization of fluids, bitumen ad rock matrix in the reservoir. New equipment and analytical solutions for naturally fractured reservoir were also included in this study. Main purpose of the reservoir geochemistry is to understand the origin of fluids (gas, petroleum and water) and distribution of the bitumens within the reservoir and to use them not only for exploration but development of the petroleum. For the theme of reservoir geochemistry, methods and principles of the reservoir gas and bitumen characterization, which is applicable to the petroleum development, are studied. and case study was carried out on the gas, water and bitumen samples in the reservoir taken form Haenam area and Ulleung Basin offshore Korea. Gases taken form the two different wells indicate the different origin. Formation water analyses show the absence of barrier within the tested interval. With the sidewall core samples from a well offshore Korea, the analysis using polarizing microscope, scanning electron microscope with EDX and cathodoluminoscope was performed for the study on sandstone diagenesis. The I/S changes were examined on the cuttings samples from a well, offshore Korea to estimate burial temperature. Oxygen stable isotope is used to study geothermal history in sedimentary basin. Study in the field is rare in Korea and basic data are urgently needed especially in continental basins to determine the value of formation water. In the test analyses, three samples from marine basins indicate final temperature from 55 deg.C to 83 deg.C and one marine sample indicate the initial temperature of 36 deg.C. One sample from continental basin represented the final temperature from 53 and 80 deg.C. These temperatures will be corrected because these values were based on assumed

Numerical simulation of roadway support in a sandstone-type uranium mine

International Nuclear Information System (INIS)

Liu Huipeng; Li Yu; Song Lixia

2009-01-01

At present, the most surrounding rocks of sandstone-type uranium mines in China are mudstone, sandstone, pelitic siltstone, and so on. They show the characteristics of soft rock. Such uranium deposit is not fit for in-situ leaching. If the uranium ores are mined by conventional mining method, one of the problems to be solved is the support technique in the soft rock roadway. So, taking a uranium mine in Inner Mongolia as the research object, the support technique in the soft rock roadway of the sandstone-type uranium deposits is studied. Through on-site engineering geological investigation and laboratory test, the main reasons for roadway damage are analyzed. A technique of support in the soft rock roadway of sandstone-type uranium deposits is put forward by drawing on the expericnce of soft rock roadway support in coal mines. The roadway shape and support parameters are optimized by using a numerical simulation method. The results verified the feasibility of the supporting technique. (authors)

Sediment transport direction in fluviatile Karharbari sandstone, Giridih Basin, Bihar

Energy Technology Data Exchange (ETDEWEB)

Tewari, R C; Casshyap, S M

1978-01-01

The sandstone is pebbly, very coarse grained in the lower part, and coarse to medium grained in the upper part. Shale and coal respectively constitute 9 and 5% of the strata Small and large erosional channels and successive sets of large scale cross-bedding characterize the sandstone. Palaeo- currents reveal that the paleodrainage and sediment transport were dominantly directed from SSW to NNE.

Sensitivity of CO2 storage performance to varying rates and dynamic injectivity in the Bunter Sandstone, UK

Science.gov (United States)

Kolster, C.; Mac Dowell, N.; Krevor, S. C.; Agada, S.

2016-12-01

Carbon capture and storage (CCS) is needed for meeting legally binding greenhouse gas emissions targets in the UK (ECCC 2016). Energy systems models have been key to identifying the importance of CCS but they tend to impose few constraints on the availability and use of geologic CO2 storage reservoirs. Our aim is to develop simple models that use dynamic representations of limits on CO2 storage resources. This will allow for a first order representation of the storage reservoir for use in systems models with CCS. We use the ECLIPSE reservoir simulator and a model of the Southern North Sea Bunter Sandstone saline aquifer. We analyse reservoir performance sensitivities to scenarios of varying CO2 injection demand for a future UK low carbon energy market. With 12 injection sites, we compare the impact of injecting at a constant 2MtCO2/year per site and varying this rate by a factor of 1.8 and 0.2 cyclically every 5 and 2.5 years over 50 years of injection. The results show a maximum difference in average reservoir pressure of 3% amongst each case and a similar variation in plume migration extent. This suggests that simplified models can maintain accuracy by using average rates of injection over similar time periods. Meanwhile, by initiating injection at rates limited by pressurization at the wellhead we find that injectivity steadily increases. As a result, dynamic capacity increases. We find that instead of injecting into sites on a need basis, we can strategically inject the CO2 into 6 of the deepest sites increasing injectivity for the first 15 years by 13%. Our results show injectivity as highly dependent on reservoir heterogeneity near the injection site. Injecting 1MTCO2/year into a shallow, low permeability and porosity site instead of into a deep injection site with high permeability and porosity reduces injectivity in the first 5 years by 52%. ECCC. 2016. Future of Carbon Capture and Storage in the UK. UK Parliament House of Commons, Energy and Climate Change

Traces of the heritage arising from the Macelj sandstone

Science.gov (United States)

Golež, Mateja

2014-05-01

The landscape of Southeast Slovenia and its stone heritage principally reveal itself through various Miocene sandstones. The most frequently found type on the borderline between Slovenia and Croatia, i.e. east of Rogatec, is the micaceous-quartz Macelj sandstone. This rock ranges in colour from greenish grey to bluish grey and yellowish, depending on the content of glauconite, which colours it green. In its composition, the rock is a heterogeneous mixture of grains of quartz, dolomite, muscovite, microcline, anorthite and glauconite. The average size of grains is 300μm. In cross-section, they are oblong, semi-rounded or round. The mechanical-physical and durability properties of the Macelj sandstone, which have been characterised pursuant to the applicable standards for natural stone, reveal that the rock exhibits poor resistance to active substances from the atmosphere, particularly in the presence of salt. In the surroundings of Rogatec, there are around 45 abandoned quarries of the Macelj sandstone, which are the result of the exploitation of this mineral resource from the 17th century on. The local quarrymen earned their bread until 1957, when the Kambrus quarry industry closed down. From the original use of this mineral resource as construction and decorative material, the useful value of the Macelj sandstone expanded during the development of the metals industry to the manufacture of large and small grindstones for the needs of the domestic and international market. Therefore, traces of quarrying can not only be seen in the disused quarries, but also in the rich architectural heritage of Rogatec and its surroundings, the stone furniture - from portals, window frames, wells, various troughs, pavements to stone walls - and other. The living quarrying heritage slowly passed into oblivion after World War II, although the analysis of the social image of the people residing in Rogatec and its surroundings revealed that there was an average of one stonemason in

Middle Ordovician brachiopods from the Stairway Sandstone, Amadeus Basin, central Australia

DEFF Research Database (Denmark)

Jakobsen, Kristian Grube; Brock, Glenn A.; Nielsen, Arne Thorshøj

2014-01-01

-water palaeoenvironment along the margin of northeastern Gondwana. The brachiopods from the Stairway Sandstone are of low diversity and represent ca 9% of the entire shelly fauna. Five brachiopod taxa are described from the Stairway Sandstone; all are endemic to the Amadeus Basin at species level. Two new species...

Variability of 14C reservoir age and air-sea flux of CO2 in the Peru-Chile upwelling region during the past 12,000 years

Science.gov (United States)

Carré, Matthieu; Jackson, Donald; Maldonado, Antonio; Chase, Brian M.; Sachs, Julian P.

2016-01-01

The variability of radiocarbon marine reservoir age through time and space limits the accuracy of chronologies in marine paleo-environmental archives. We report here new radiocarbon reservoir ages (ΔR) from the central coast of Chile ( 32°S) for the Holocene period and compare these values to existing reservoir age reconstructions from southern Peru and northern Chile. Late Holocene ΔR values show little variability from central Chile to Peru. Prior to 6000 cal yr BP, however, ΔR values were markedly increased in southern Peru and northern Chile, while similar or slightly lower-than-modern ΔR values were observed in central Chile. This extended dataset suggests that the early Holocene was characterized by a substantial increase in the latitudinal gradient of marine reservoir age between central and northern Chile. This change in the marine reservoir ages indicates that the early Holocene air-sea flux of CO2 could have been up to five times more intense than in the late Holocene in the Peruvian upwelling, while slightly reduced in central Chile. Our results show that oceanic circulation changes in the Humboldt system during the Holocene have substantially modified the air-sea carbon flux in this region.

Application potential of sequence stratigraphy to prospecting for sandstone-type uranium deposit in continental depositional basins

International Nuclear Information System (INIS)

Li Shengxiang; Chen Zhaobo; Chen Zuyi; Xiang Weidong; Cai Yuqi

2001-01-01

Sequence stratigraphy has been widely used in hydrocarbon exploration and development, and great achievements have been achieved. However, its application to the prospecting for sandstone-type uranium deposits is just beginning. The metallogenic characteristics of sandstone-type uranium deposits and those of oil and gas are compared, and the relationship between sandstone-type uranium metallogenesis and the system tracts of sequence stratigraphy is studied. The authors propose that highest and system tracts are the main targets for prospecting interlayer oxidation zone type sandstone uranium deposits, and the incised valleys of low stand system tracts are favourable places for phreatic oxidation zone type sandstone uranium deposits, and transgressive system tracts are generally unfavorable to the formation of in-situ leachable sandstone-type uranium deposits. Finally, the authors look ahead the application potential of sequence stratigraphy to the prospecting for sandstone-type uranium deposits in continental depositional basins

Smart waterflooding in carbonate reservoirs

Energy Technology Data Exchange (ETDEWEB)

Zahid, A.

2012-02-15

During the last decade, smart waterflooding has been developed into an emerging EOR technology both for carbonate and sandstone reservoirs that does not require toxic or expensive chemicals. Although it is widely accepted that different salinity brines may increase the oil recovery for carbonate reservoirs, understanding of the mechanism of this increase is still developing. To understand this smart waterflooding process, an extensive research has been carried out covering a broad range of disciplines within surface chemistry, thermodynamics of crude oil and brine, as well as their behavior in porous media. The main conclusion of most previous studies was that it is the rock wettability alteration towards more water wetting condition that helps improving the oil recovery. In the first step of this project, we focused on verifying this conclusion. Coreflooding experiments were carried out using Stevens Klint outcrop chalk core plugs with brines without sulfate, as well as brines containing sulfate in different concentrations. The effects of temperature, injection rate, crude oil composition and different sulfate concentrations on the total oil recovery and the recovery rate were investigated. Experimental results clearly indicate improvement of the oil recovery without wettability alteration. At the second step of this project, we studied crude oil/brine interactions under different temperatures, pressures and salinity conditions in order to understand mechanisms behind the high salinity waterflooding. Our results show, in particular that sulfate ions may help decreasing the crude oil viscosity or formation of, seemingly, an emulsion phase between sulfate-enriched brine and oil at high temperature and pressure. Experimental results indicate that crude oils interact differently with the same brine solutions regarding phase behavior and viscosity measurements. This difference is attributed to the difference in composition of the different crude oils. More experiments

Testing the process of drilling - analysis of drilling performance in variegated sandstone and Keuper in Northern Germany; Der Bohrprozess auf dem Pruefstand - Analyse der Bohrleistungen im Buntsandstein und Keuper in Norddeutschland

Energy Technology Data Exchange (ETDEWEB)

Pust, G.; Tschaffler, H. [Mobil Erdgas Erdoel GmbH, Celle (Germany); Grunwald, R. [BEB Erdgas und Erdoel GmbH, Nienhagen (Germany); Gloth, H. [TU Bergakademie Freiberg (Germany); Marx, C. [ITE, Clausthal-Zellerfeld (Germany)

1998-12-31

The aim of the project launched jointly by DGMK and 5 companies from the German oil- and gas industry and two institutes for drilling technologies was to find suitable ways in which the drilling progress in formations with bad drilling conditions in Northern Germany, i.e. lower and middle variegated sandstone and Keuper can be increases in order to bring costs down. The borehole sunk in Northern Germany were surveyed and inventorised. Data were subjected to a thorough statistical analysis in order to obtain optimal drilling parameters and improve the drilling tools. Basic studies on rock damaging were also to be included in order to better understand the processes. Finally, the project aims at realising the optimal drilling parameters, increase drilling progress, use improved drilling machinery and thus cut costs. (orig.) [Deutsch] Ziel des DGMK-Gemeinschaftsprojektes mit 5 Firmen der deutschen Erdoel- und Erdgasindustrie sowie 2 bohrtechnischen Instituten war es, durch geeignete Massnahmen den Bohrfortschritt in schlechtbohrbaren Formationen in Norddeutschland, naemlich unterer und mittlerer Buntsandstein sowie Keuper, zu erhoehen und damit einen Beitrag zur Kostensenkung zu leisten. Um dieses Ziel zu erreichen, sollte eine Bestandsaufnahme der in Norddeutschland abgeteuften Bohrungen erfolgen. Die Daten sollten einer eingehenden statistischen Auswertung unterzogen werden. Hieraus sollten optimale Bohrparameter und Verbesserungen der Bohrwerkzeuge abgeleitet werden. Ferner sollten grundlegende Untersuchungen zur Gesteinszerstoerung herangezogen werden, um ein besseres Verstaendnis fuer die ablaufenden Prozesse zu bekommen. Durch die Realisierung optimaler Bohrparameter und den Einsatz verbesserter Bohrwerkszeuge sollte schliesslich die Erhoehung des Bohrfortschritts und damit eine Senkung der Kosten erreicht werden. (orig.)

Discussion on metallogenic prospect of sandstone-type uranium deposit in Yabulai basin

International Nuclear Information System (INIS)

Wang Lianshe; Li Xiangping

2003-01-01

Based on characteristics of initial basin type and tectonic reworking process, this article analyses the distribution features of depositional system and subsequent alteration of the target horizon of sandstone-type uranium deposits in Yabulai basin. Guided by prognostic criteria of sandstone-type uranium deposits, authors suggest that the post-depositional tectonic reworking in the basin was quite intense, and uranium metallogenic prospects are unfavorable. However, the Lower Cretaceous in the paleo-slope at the middle of the basin does show certain metallogenic prospects for sandstone-type uranium deposits

Multidisciplinary studies on ancient sandstone quarries of Western Sardinia (Italy).

Science.gov (United States)

Grillo, Silvana Maria; Del Vais, Carla; Naitza, Stefano

2013-04-01

The ancient coastal quarries of Mediterranean are increasingly considered geosites of multidisciplinary relevance. They are sites of historical-archaeological interest that show ancient techniques of stone extraction; they are significant for cultural heritage conservation and restoration, as sources of the stones used in ancient buildings and monuments; they are sites of geological relevance, as often retain important stratigraphic sections; they are also useful markers of secular changes in the sea level. A multisciplinary study is in progress on the ancient quarries of the Sinis region (western Sardinia island), integrating archaeological, geological, minero-petrographical data. In Sardinia, coastal quarries have been established from Punic and Roman times. Many of them exploited Quaternary sediments along the southern and western coasts of the island. They consist of middle-late Pleistocene marine conglomerates and carbonate sandstones, and of coastal (aeolian) carbonate sandstones. Sandstone blocks of different sizes have been widely used in ancient cities for buildings, defensive works, harbours, etc. Three main areas of stone extraction (San Giovanni di Sinis, Punta Maimoni, Is Arutas) have been so far recognized in the Sinis. GIS-supported mapping and documentation of the sites includes their geology and stratigraphy, the extension and layout of the quarries, and an evaluation of volumes of extracted rocks. Documented archaeological evidences include ancient extraction fronts, spoil heaps, working areas, working traces in the old fronts, transport routes of blocks, and traces of loading facilities. The study is aimed at reconstructing the relationships of the quarries with the urban areas of Sinis, as the ancient Punic-Roman city of Tharros. Consequently, a minero-petrographical characterization (optical microscopy, XRD) is performed on sandstones sampled in each quarry, and in historical buildings in Tharros and other centres of the region (Cabras

Characteristics of isotope geology of sandstone-type uranium deposit in Turpan-Hami Basin

International Nuclear Information System (INIS)

Liu Hanbin; Xia Yuliang; Lin Jinrong; Fan Guang

2003-01-01

This paper expounds the isotope characteristics of in-situ leachable sandstone-type uranium deposit of Shihongtan in the southwestern part of Turpan-Hami basin. The results suggest that uranium mineralization age of 48 ± 2 Ma and 28 ± 4 Ma are obtained. The ages of the porphyritic granite and gneissic granite from the southwestern area are 422 ± 5 Ma and 268 ± 23 Ma. The U-Pb age of clastic zircons from ore-bearing sandstone is 283 ± 67 Ma, which is corresponding to the age of gneissic granite of the provenance area indicating the material source of uraniferous sandstone.Based. The sources are uraniferous sandstone accumulated during the deposition and the uranium leached from provenance area rocks by weathering. (authors)

Applying reaction condition index to predict sandstone type uranium deposit

International Nuclear Information System (INIS)

Chen Gongxin; Liu Jinhui; Cheng Hai

2002-01-01

On the basic of the explanation of reaction condition index, the deduction of reaction condition index calculation principle, the hydrogeological setting in Gongpoquan basin in Baishan, Gansu province and the study of reaction condition index of its water source point, the north Luotuoquan area in Gongpoquan basin seems to be a favourable place for sandstone type uranium deposit, and the prospect area for sandstone type uranium deposit is delimitated

Marine radiocarbon reservoir age variation in Donax obesulus shells from northern Peru: late Holocene evidence for extended El Niño

Science.gov (United States)

Etayo-Cadavid, Miguel F.; Andrus, C. Fred T.; Jones, Kevin B.; Hodgins, Gregory W. L.; Sandweiss, Daniel H.; Uceda-Castillo, Sandiago; Quilter, Jeffrey

2013-01-01

For at least 6 m.y., El Niño events have posed the greatest environmental risk on the Peruvian coast. A better understanding of El Niño is essential for predicting future risk and growth in this tropical desert. To achieve this we analyzed archaeological and modern pre-bomb shells from the surf clam Donax for the radiocarbon reservoir effect (ΔR) to characterize late Holocene coastal upwelling conditions in northern Peru (8°14′S). Mean ΔR values from these shells suggest that modern upwelling conditions in this region were likely established between A.D. 539 and A.D. 1578. Our radiocarbon data suggest that upwelling conditions ca. A.D. 539 were less intense than those in modern times. The observed coastal water enrichment in 14C may be consequence of frequent strong El Niño events or extended El Niño–like conditions. These ΔR-inferred marine conditions are in agreement with proposed extended El Niño activity in proxy and archaeological records of ca. A.D. 475–530. Extended El Niño conditions have been linked to political destabilization, societal transformation, and collapse of the Moche civilization in northern Peru. A return to such conditions would have significant impacts on the dense population of this region today and in the near future.

Experimental investigation of methane release from hydrate formation in sandstone through both hydrate dissociation and CO{sub 2} sequestration

Energy Technology Data Exchange (ETDEWEB)

Husebo, J.; Graue, A.; Kvamme, B. [Bergen Univ., Bergen (Norway). Dept. of Physics and Technology; Stevens, J.; Howard, J.J. [ConocoPhillips, Ponca City, OK (United States); Baldwin, B.A. [Green Country Petrophysics LLC, Dewey, OK (United States)

2008-07-01

Large amounts of natural gas trapped in hydrate reservoirs are found in Arctic regions and in deep offshore locations around the world. Natural gas production from hydrate deposits offer significant potential for future energy needs. However, research is needed in order to propose potential production schemes for natural gas hydrates. Natural gas molecules can be freed from hydrate structured cages by depressurization, by heating and by exposing the hydrate to a substance that will form a thermodynamically more stable hydrate structure. This paper provided a comparison of two approaches for releasing methane from methane hydrate in porous sandstone. The study scope covered the dissociation rate of methane hydrate in porous media through depressurization, and also referred to previous work done on producing methane from hydrates in sandstone while sequestering carbon dioxide (CO{sub 2}). The study was conducted in a laboratory setting. The paper discussed the experimental design which included the placing of a pressure- and temperature-controlled sample holder inside the bore of a magnetic resonance imager. The experimental procedures were then outlined, with reference to hydrate formation; carbon dioxide sequestration; hydrate dissociation experiments with constant volume; and hydrate dissociation experiments at constant pressure. The constant volume experiments demonstrated that in order to dissociate a large amount of hydrate, the initial depressurization had to be significantly lower than the hydrate stability pressure. 9 refs., 9 figs.

Predicting petrophysical properties by simultaneous inversion of seismic and reservoir engineering data

Science.gov (United States)

Mantilla, Andres Eduardo

physics and seismic characterization of the fluvial sandstones in the Cretaceous K2 Unit of the Apiay-Guatiquia Oil Field. First I study the relationship between petrophysical and seismic properties for the K2 Unit reservoir rocks, at the pore, well log, and field scales. Then, I apply the joint inversion methodology I propose to the estimation of porosity and permeability in the drainage area of one of the wells in this field.

The Controls of Pore-Throat Structure on Fluid Performance in Tight Clastic Rock Reservoir: A Case from the Upper Triassic of Chang 7 Member, Ordos Basin, China

Directory of Open Access Journals (Sweden)

Yunlong Zhang

2018-01-01

Full Text Available The characteristics of porosity and permeability in tight clastic rock reservoir have significant difference from those in conventional reservoir. The increased exploitation of tight gas and oil requests further understanding of fluid performance in the nanoscale pore-throat network of the tight reservoir. Typical tight sandstone and siltstone samples from Ordos Basin were investigated, and rate-controlled mercury injection capillary pressure (RMICP and nuclear magnetic resonance (NMR were employed in this paper, combined with helium porosity and air permeability data, to analyze the impact of pore-throat structure on the storage and seepage capacity of these tight oil reservoirs, revealing the control factors of economic petroleum production. The researches indicate that, in the tight clastic rock reservoir, largest throat is the key control on the permeability and potentially dominates the movable water saturation in the reservoir. The storage capacity of the reservoir consists of effective throat and pore space. Although it has a relatively steady and significant proportion that resulted from the throats, its variation is still dominated by the effective pores. A combination parameter (ε that was established to be as an integrated characteristic of pore-throat structure shows effectively prediction of physical capability for hydrocarbon resource of the tight clastic rock reservoir.

Investigation of the petrophysical properties of a porous sandstone sample using confocal scanning laser microscopy

Energy Technology Data Exchange (ETDEWEB)

Petford, N. [Kingston Univ., Centre for Earth and Environmental Science Research, Kingston (United Kingdom); Davidson, G. [University Coll., Dept. of Electronic and Electrical Engineering, London (United Kingdom); Miller, J.A. [Cambridge Univ., Dept. of Earth Sciences, Cambridge (United Kingdom)

2001-05-01

Confocal scanning laser microscopy (CSLM) is used to produce images of the two- and three-dimensional distribution and geometry of pore space in a reservoir sandstone and measure the 2D distribution of pore throat radii. Non-destructive serial sectioning of the rock using laser light at 100% illumination, combined with image thresholding and histogram equalization techniques allow the pore volume structure of the uppermost 100 {mu}m of the sample to be reconstructed. Negative imaging of the pore volume gave superior depth and feature resolution compared to positive (reflection) imaging. Artefacts encountered in applying classical Medial Axial Transforms to CSLM images include branch networks dominated by coordination numbers of 3. Skeletonization using Euclidean distance maps gives increased accuracy in the description of the pore network. Measured pore throat size distribution in the rock is strongly exponential and described by the expression y 219e{sup -0.25x} where y is the number of pore throats. (Author)

Reservoir petrophysics and hydrocarbon occurrences of the Bahariya Formation, Alamein-Yidma fields, Western Desert of Egypt

Energy Technology Data Exchange (ETDEWEB)

Abdel-Aziz Younes, Mohamed [Alexandria Univ. (Egypt). Geology Dept.

2012-12-15

The Bahariya Formation of Cenomanian age is considered to be one of the main oil and gas accumulations in most of the fields of the Western Desert basins. The lithostratigraphic succession of the Bahariya Formation is classified into two main sand units (Unit I and Unit III) separated by shalesiltstone (Unit II). The sandstone of unit-I and III is characterized by being highly enriched in shale content especially glauconite in all wells of the Alamein Field, that has an obvious negative effect on the porosity and oil saturation, where the glauconite increases the grain density of sandstone reservoirs from 2.65 g/cm{sup 3} up to 2.71 g/cm{sup 3}. The well logging data and petrophysical characteristics conducted on Alamein well-28 involving analysis of 30 core samples, were used to evaluate the reservoir characterization and hydrocarbon potentialities. The petrophysical parameters indicate that the primary porosity values are between 8.7 and 29.1%. Decreasing porosity is related to the increase of shale content from 9 to 13%, which occurs as a dispersed habitat. The water saturation changes from 43 to 80%, while the hydrocarbon saturation ranges from 12.1 to 37%. Promising hydrocarbon accumulations are displayed by the sandstone of unit-III due to increased hydrocarbon saturation and effective porosity, thus reflecting the high quality reservoir of this unit. The irreducible and movable hydrocarbon distribution shows a general increase at the eastern and western flanks of the faulted anticline in the Alamein-Yidma fields. The biomarker characteristics and stable carbonisotopic composition of the Bahariya crude oils recovered from the Alamein Field show no obvious variations among them. These oils are paraffinic, containing little branched or cyclic materials waxy n-alkanes(C{sub 25}-C{sub 31}) and characterized by high API gravity, low sulfur content, oleanane index < 2% and moderately high pristane/phytaneratio > 1 and CPI > 1 and the canonical variable parameter is

A combination of streamtube and geostatical simulation methodologies for the study of large oil reservoirs

Energy Technology Data Exchange (ETDEWEB)

Chakravarty, A.; Emanuel, A.S.; Bernath, J.A. [Chevron Petroleum Technology Company, LaHabra, CA (United States)

1997-08-01

The application of streamtube models for reservoir simulation has an extensive history in the oil industry. Although these models are strictly applicable only to fields under voidage balance, they have proved to be useful in a large number of fields provided that there is no solution gas evolution and production. These models combine the benefit of very fast computational time with the practical ability to model a large reservoir over the course of its history. These models do not, however, directly incorporate the detailed geological information that recent experience has taught is important. This paper presents a technique for mapping the saturation information contained in a history matched streamtube model onto a detailed geostatistically derived finite difference grid. With this technique, the saturation information in a streamtube model, data that is actually statistical in nature, can be identified with actual physical locations in a field and a picture of the remaining oil saturation can be determined. Alternatively, the streamtube model can be used to simulate the early development history of a field and the saturation data then used to initialize detailed late time finite difference models. The proposed method is presented through an example application to the Ninian reservoir. This reservoir, located in the North Sea (UK), is a heterogeneous sandstone characterized by a line drive waterflood, with about 160 wells, and a 16 year history. The reservoir was satisfactorily history matched and mapped for remaining oil saturation. A comparison to 3-D seismic survey and recently drilled wells have provided preliminary verification.

Emissions from hydroelectric reservoirs and comparison of hydroelectricity, natural gas and oil

International Nuclear Information System (INIS)

Gagnon, L.; Chamberland, A.

1993-01-01

When reservoirs are created, a small fraction of the flooded organic matter decomposes into humic acids, carbon dioxide (CO 2 ), methane (CH 4 ), nitrogen, phosphorus, and other elements. The major greenhouse gases produced are CO 2 and CH 4 . For northern projects, Canadian studies on emissions from hydroelectric reservoirs have reached similar conclusions: Emissions, including methane, are less than 35 kg CO 2 equivalent per MWh. Using a typical project in northern Quebec as the basis for analysis, none of the studies dispute the considerable advantages of hydroelectricity regarding greenhouse gas emissions. Taking into account all components of energy systems, emissions of greenhouse gases from natural-gas power plants are 24 to 26 times greater than emissions from hydroelectric plants. The Freshwater Institute, in an article published in Ambio suggests that emissions from hydroelectric plants could be a significant source of greenhouse gases. This conclusion does not apply to most hydroelectric projects for two reasons: First, the Freshwater Institute's studies concerned flooded peatlands and shallow reservoirs that are not typical of most hydro projects; and second, the Institute analyzed a hydro project with a ratio of flooded area to energy production that is 6 to 10 times higher than typical projects in Canada. 7 refs, 4 tabs

Study of cyanotoxins presence from experimental cyanobacteria concentrations using a new data mining methodology based on multivariate adaptive regression splines in Trasona reservoir (Northern Spain).

Science.gov (United States)

Garcia Nieto, P J; Sánchez Lasheras, F; de Cos Juez, F J; Alonso Fernández, J R

2011-11-15

There is an increasing need to describe cyanobacteria blooms since some cyanobacteria produce toxins, termed cyanotoxins. These latter can be toxic and dangerous to humans as well as other animals and life in general. It must be remarked that the cyanobacteria are reproduced explosively under certain conditions. This results in algae blooms, which can become harmful to other species if the cyanobacteria involved produce cyanotoxins. In this research work, the evolution of cyanotoxins in Trasona reservoir (Principality of Asturias, Northern Spain) was studied with success using the data mining methodology based on multivariate adaptive regression splines (MARS) technique. The results of the present study are two-fold. On one hand, the importance of the different kind of cyanobacteria over the presence of cyanotoxins in the reservoir is presented through the MARS model and on the other hand a predictive model able to forecast the possible presence of cyanotoxins in a short term was obtained. The agreement of the MARS model with experimental data confirmed the good performance of the same one. Finally, conclusions of this innovative research are exposed. Copyright © 2011 Elsevier B.V. All rights reserved.

Bathymetry and capacity of Shawnee Reservoir, Oklahoma, 2016

Science.gov (United States)

Ashworth, Chad E.; Smith, S. Jerrod; Smith, Kevin A.

2017-02-13

Shawnee Reservoir (locally known as Shawnee Twin Lakes) is a man-made reservoir on South Deer Creek with a drainage area of 32.7 square miles in Pottawatomie County, Oklahoma. The reservoir consists of two lakes connected by an equilibrium channel. The southern lake (Shawnee City Lake Number 1) was impounded in 1935, and the northern lake (Shawnee City Lake Number 2) was impounded in 1960. Shawnee Reservoir serves as a municipal water supply, and water is transferred about 9 miles by gravity to a water treatment plant in Shawnee, Oklahoma. Secondary uses of the reservoir are for recreation, fish and wildlife habitat, and flood control. Shawnee Reservoir has a normal-pool elevation of 1,069.0 feet (ft) above North American Vertical Datum of 1988 (NAVD 88). The auxiliary spillway, which defines the flood-pool elevation, is at an elevation of 1,075.0 ft.The U.S. Geological Survey (USGS), in cooperation with the City of Shawnee, has operated a real-time stage (water-surface elevation) gage (USGS station 07241600) at Shawnee Reservoir since 2006. For the period of record ending in 2016, this gage recorded a maximum stage of 1,078.1 ft on May 24, 2015, and a minimum stage of 1,059.1 ft on April 10–11, 2007. This gage did not report reservoir storage prior to this report (2016) because a sufficiently detailed and thoroughly documented bathymetric (reservoir-bottom elevation) survey and corresponding stage-storage relation had not been published. A 2011 bathymetric survey with contours delineated at 5-foot intervals was published in Oklahoma Water Resources Board (2016), but that publication did not include a stage-storage relation table. The USGS, in cooperation with the City of Shawnee, performed a bathymetric survey of Shawnee Reservoir in 2016 and released the bathymetric-survey data in 2017. The purposes of the bathymetric survey were to (1) develop a detailed bathymetric map of the reservoir and (2) determine the relations between stage and reservoir storage

Sedimentological Characteristics and Re-interpretation of the Paleoenvironment of Lokoja Sandstone, Southern Bida Basin, Nigeria

International Nuclear Information System (INIS)

Ojo, O. J.; Akande, S. O.

2002-01-01

Detail mapping of the Lokoja Formation consisting predominantly of sandstones exposed along Okene-Abuja highway near the confluence of Rivers Niger and Benue in the southern Bida Basin was undertaken in an attempt to reconstruct their depositional history. The analyses of the lithofacies characteristics, pebble morphogenesis and ichnofossil content of the Lokoja sandstones in the study area reveal their depositional environments which evolved from alluvial fans through braided stream into nearshore shallow marine conditions. The massive, immature, matrix to grain supported conglomerate subfacies can be interpreted as debris flow. The conglomeratic sandstone facies (massive, cross stratified and graded subfacies) reflect deposits of deep braided channels. The bioturbated and herringbone cross stratified conglomeratic sandstones indicate shallowing to marginal marine environments. The fine to medium grained sandstones, siltstones and claystones are interpreted as channel bars and floodplain deposits.Results of pebble morphogenesis analysis indicate predominance of fluvial processes. Minor high energy (probably beach) condition is indicated by some individual clasts from the conglomeratic sandstone facies with sphericity and OP index values less that 0.66 and -1.5 respectively.The study is significant because it represents the first sedimentological evidence of influence of shallow marine in the development of Lokoja sandstones during Campanian-Maastrichtian times

Significant breakthrough in proprietary deepwater natural gas exploration in the northern South China Sea and its inspiration

Directory of Open Access Journals (Sweden)

Yuhong Xie

2014-12-01

Full Text Available In 2014, Zhanjiang Branch of CNOOC Limited obtained high oil and gas flows (160 × 104 m3/d in Well LS 17-2-1 in northern South China Sea. The tested formation is the Neogene Upper Miocene Huangliu Fm. This is the first self-explored natural gas field in deep water area in China. Exploration in this area underwent three periods: (1 Reconnaissance exploration period (before 2002: Limited by techniques, the major exploration was in shallow water areas; (2 Foreign cooperative exploration period (2002–2012: As the discovered reserve scale was small, and there is no economic benefit, the partners successively gave up their exploration equities in the deep water area of western South China Sea; however, the high quality source rocks and reservoirs were confirmed in the deep water area of the South China Sea, revealing the mask of hydrocarbon exploration in this region; (3 Self-exploration period (since 2013: Relying on national science and technology major projects and its scientific research and production, Zhanjiang Company of CNOOC conducted several scientific researches on seismic data acquisition and processing, high-quality reservoir distribution, key factors for hydrocarbon accumulation in deep water areas, optimized and confirmed Lingshui 17-2 structure as the first drilling target, and obtained significant exploration breakthrough. Lingshui 17-2 structure is located in the Ledong-Lingshui section of the Central Canyon. Its major target layer is the Huangliu Fm. Its total thickness is over 150 m, with sandstone ratio of 75.4%, maximum single layer thickness of 52 m, porosity ranging 30.0%–33.7% (31.5% averagely, permeability ranging 293–2512 mD (633 mD averagely, belonging to reservoir with ultrahigh porosity and high-ultrahigh permeability. The exploration breakthrough in Lingshui 17-2 shows the giant potentiality of hydrocarbon exploration in this deep water area.

PALEOEVIRONMENT OF NIGERIA'S AJALI SANDSTONES: A ...

African Journals Online (AJOL)

The Ajali Sandstone is a major clastic formation of Campanian-Maastrichtian age occuring within the Anambra Basin, Southeastern Nigeria. ... The result is in line with earlier conclusions of fluvial or fluviodeltaic depositional environment based on analysis of faceis, sedimentary rock which are suitable for morphometrical ...

Ordovician of the Sauk megasequence in the Ozark region of northern Arkansas and parts of Missouri and adjacent states: Chapter 11

Science.gov (United States)

Ethington, Raymond L.; Repetski, John E.; Derby, James R.

2012-01-01

Exposures of Ordovician rocks of the Sauk megasequence in Missouri and northern Arkansas comprise Ibexian and lower Whiterockian carbonates with interspersed sandstones. Subjacent Cambrian strata are exposed in Missouri but confined to the subsurface in Arkansas. The Sauk-Tippecanoe boundary in this region is at the base of the St. Peter Sandstone. Ulrich and associates divided the Arkansas section into formations early in the 20th century, principally based on sparse collections of fossil invertebrates. In contrast, the distribution of invertebrate faunas and modern studies of conodonts will be emphasized throughout this chapter. Early workers considered many of the stratigraphic units to be separated by unconformities, but modern analysis calls into question the unconformable nature of some of their boundaries. The physical similarity of the several dolomites and sandstones, complex facies relations, and lack of continuous exposures make identification of individual formations difficult in isolated outcrops.

Elastic Dispersion and Attenuation in Fully Saturated Sandstones: Role of Mineral Content, Porosity, and Pressures

Science.gov (United States)

Pimienta, Lucas; Borgomano, Jan V. M.; Fortin, Jérôme; Guéguen, Yves

2017-12-01

Because measuring the frequency dependence of elastic properties in the laboratory is a technical challenge, not enough experimental data exist to test the existing theories. We report measurements of three fluid-saturated sandstones over a broad frequency band: Wilkenson, Berea, and Bentheim sandstones. Those sandstones samples, chosen for their variable porosities and mineral content, are saturated by fluids of varying viscosities. The samples elastic response (Young's modulus and Poisson's ratio) and hydraulic response (fluid flow out of the sample) are measured as a function of frequency. Large dispersion and attenuation phenomena are observed over the investigated frequency range. For all samples, the variation at lowest frequency relates to a large fluid flow directly measured out of the rock samples. These are the cause (i.e., fluid flow) and consequence (i.e., dispersion/attenuation) of the transition between drained and undrained regimes. Consistently, the characteristic frequency correlates with permeability for each sandstone. Beyond this frequency, a second variation is observed for all samples, but the rocks behave differently. For Berea sandstone, an onset of dispersion/attenuation is expected from both Young's modulus and Poisson's ratio at highest frequency. For Bentheim and Wilkenson sandstones, however, only Young's modulus shows dispersion/attenuation phenomena. For Wilkenson sandstone, the viscoelastic-like dispersion/attenuation response is interpreted as squirt flow. For Bentheim sandstone, the second effect does not fully follow such response, which could be due to a lower accuracy in the measured attenuation or to the occurence of another physical effect in this rock sample.

Design philosophy and practice of asymmetrical 3D fracturing and random fracturing: A case study of tight sand gas reservoirs in western Sichuan Basin

Directory of Open Access Journals (Sweden)

Jianchun Guo

2015-03-01

Full Text Available At present two technical models are commonly taken in tight gas reservoir stimulation: conventional massive fracturing and SRV fracturing, but how to select a suitable fracturing model suitable for reservoir characteristics is still a question waiting to be answered. In this paper, based on the analysis of geological characteristics and seepage mechanism of tight gas and shale gas reservoirs, the differences between stimulation philosophy of tight gas reservoirs and shale reservoirs are elucidated, and the concept that a suitable stimulation model should be selected based on reservoir geological characteristics and seepage mechanism aiming at maximally improving the seepage capability of a reservoir. Based on this concept, two fracturing design methods were proposed for two tight gas reservoirs in western Sichuan Basin: asymmetrical 3D fracturing design (A3DF for the middle-shallow Upper Jurassic Penglaizhen Fm stacked reservoirs in which the hydraulic fractures can well match the sand spatial distribution and seepage capability of the reservoirs; SRV fracturing design which can increase fracture randomness in the sandstone and shale laminated reservoirs for the 5th Member of middle-deep Upper Triassic Xujiahe Fm. Compared with that by conventional fracturing, the average production of horizontal wells fractured by A3DF increased by 41%, indicating that A3DF is appropriate for gas reservoir development in the Penglaizhen Fm; meanwhile, the average production per well of the 5th Member of the Xujiahe Fm was 2.25 × 104 m3/d after SRV fracturing, showing that the SRV fracturing is a robust technical means for the development of this reservoir.

Genetic models and their impact on uranium exploration in the Athabasca sandstone basin, Saskatchewan, Canada

International Nuclear Information System (INIS)

Strnad, J.G.

1980-01-01

While the Beaverlodge area of Northern Saskatchewan became an important uranium-producing district during the 1950s, the Athabasca sandstone basin, located in the immediate vicinity, was considered to be non-prospective in Canada's regional assessment. Twenty years later, with the introduction of the supergene model into the basin's exploration strategy, the favourability of the host-rock for uranium deposits was shown. However, in some instances the search for local targets was enriched by implementing non-supergene models. Most geologists originally favoured the Middle Proterozoic (sub-Helikian) unconformity as a unique ore-controlling feature. Later, the concept of Lower Proterozoic (Aphebian) syngenetic protore, as represented by graphite-bearing strata in Archaean proximity, was added. In the author's view the combination of these factors is productive only within specialized segments of Archaean-Lower Proterozoic (Archaean-Aphebian) contact zones. (author)

A new bee species that excavates sandstone nests.

Science.gov (United States)

Orr, Michael C; Griswold, Terry; Pitts, James P; Parker, Frank D

2016-09-12

Humanity has long been fascinated by animals with apparently unfavorable lifestyles [1]. Nesting habits are especially important because they can limit where organisms live, thereby driving population, community, and even ecosystem dynamics [2]. The question arises, then, why bees nest in active termite mounds [3] or on the rim of degassing volcanoes, seemingly preferring such hardship [4]. Here, we present a new bee species that excavates sandstone nests, Anthophora (Anthophoroides) pueblo Orr (described in Supplemental Information, published with this article online), despite the challenges already inherent to desert life. Ultimately, the benefits of nesting in sandstone appear to outweigh the associated costs in this system. Copyright © 2016 Elsevier Ltd. All rights reserved.

Restoring Natural Streamflow Variability by Modifying Multi-purpose Reservoir Operation

Science.gov (United States)

Shiau, J.

2010-12-01

Multi-purpose reservoirs typically provide benefits of water supply, hydroelectric power, and flood mitigation. Hydroelectric power generations generally do not consume water. However, temporal distribution of downstream flows is highly changed due to hydro-peaking effects. Associated with offstream diversion of water supplies for municipal, industrial, and agricultural requirements, natural streamflow characteristics of magnitude, duration, frequency, timing, and rate of change is significantly altered by multi-purpose reservoir operation. Natural flow regime has long been recognized a master factor for ecosystem health and biodiversity. Restoration of altered flow regime caused by multi-purpose reservoir operation is the main objective of this study. This study presents an optimization framework that modifying reservoir operation to seeking balance between human and environmental needs. The methodology presented in this study is applied to the Feitsui Reservoir, located in northern Taiwan, with main purpose of providing stable water-supply and auxiliary purpose of electricity generation and flood-peak attenuation. Reservoir releases are dominated by two decision variables, i.e., duration of water releases for each day and percentage of daily required releases within the duration. The current releasing policy of the Feitsui Reservoir releases water for water-supply and hydropower purposes during 8:00 am to 16:00 pm each day and no environmental flows releases. Although greater power generation is obtained by 100% releases distributed within 8-hour period, severe temporal alteration of streamflow is observed downstream of the reservoir. Modifying reservoir operation by relaxing these two variables and reserve certain ratio of streamflow as environmental flow to maintain downstream natural variability. The optimal reservoir releasing policy is searched by the multi-criterion decision making technique for considering reservoir performance in terms of shortage ratio

Fracture propagation in sandstone and slate – Laboratory experiments, acoustic emissions and fracture mechanics

Directory of Open Access Journals (Sweden)

Ferdinand Stoeckhert

2015-06-01

Full Text Available Fracturing of highly anisotropic rocks is a problem often encountered in the stimulation of unconventional hydrocarbon or geothermal reservoirs by hydraulic fracturing. Fracture propagation in isotropic material is well understood but strictly isotropic rocks are rarely found in nature. This study aims at the examination of fracture initiation and propagation processes in a highly anisotropic rock, specifically slate. We performed a series of tensile fracturing laboratory experiments under uniaxial as well as triaxial loading. Cubic specimens with edge lengths of 150 mm and a central borehole with a diameter of 13 mm were prepared from Fredeburg slate. An experiment using the rather isotropic Bebertal sandstone as a rather isotropic rock was also performed for comparison. Tensile fractures were generated using the sleeve fracturing technique, in which a polymer tube placed inside the borehole is pressurized to generate tensile fractures emanating from the borehole. In the uniaxial test series, the loading was varied in order to observe the transition from strength-dominated fracture propagation at low loading magnitudes to stress-dominated fracture propagation at high loading magnitudes.

Age, sedimentary environments, and other aspects of sandstone and related host rocks for uranium deposits

International Nuclear Information System (INIS)

1983-01-01

Project II of the Uranium Geology Working Group was assigned to the study of sedimentary basins and sandstone - type uranium deposits. About 40% of the worlds's uranium resources are contained in sandstone-type deposits, which has led to extensive research. The research was carried out mainly by correspondence, and the results reported by 21 geologists from 10 nations are summarized in this report. It investigated five topics dealing with important aspects of the geology of uranium ores in sandstone host formations: age of host rock; partitioning of uranium between continental and marine sediments; latitude limitation on formation of sandstone deposits; effect of rock formation dip on sandstone ores; usefulness of stable isotope and fluid inclusion studies. The results of studies on these subjects form part of a wider programme of the Working Group, whose final results will be presented at the 27th International Geological Congress in Moscow in 1984

Sandstone Relief Geohazards and their Mitigation: Rock Fall Risk Management in the Bohemian Switzerland National Park

Czech Academy of Sciences Publication Activity Database

Vařilová, Zuzana; Zvelebil, J.

2005-01-01

Roč. 44, - (2005), s. 53-58 ISSN 1682-5519. [Sandstone Landscapes in Europe. Past, Present and Future. International Conference on Sandstone Landscapes /2./. Vianden, 25.05.2005-28.05.2005] Keywords : sandstones * rock-slope instability * rock fall * risk evalution and mitigation * monitoring net * remedial works Subject RIV: DO - Wilderness Conservation

Study of petrological characteristics of uranium-bearing sandstone in the south of ordos basin, China

International Nuclear Information System (INIS)

Tian Cheng; Jia Licheng; Li Song; Zhang Zimin

2007-01-01

This paper discusses the relation between uranium-bearing abundance and texture constituent of sedimentary rock, on the basis of the research of petrological characteristic of sandstone in the south of Ordos basin. The influence of infiltration of sandstone and uranium migration and accumulation by the major diagenesis of compaction and cementation, clay minerals evolution, corrosion and forming of secondary porosity are discussed. Uranium-bearing sandstones are divided into four types and their petrological characteristics are discussed. After mineralization conditions being summed up, the uranium-mineralization model of sandstone-type is built. Reliable petrological evidences for evaluating favourable uranium mineralization rich areas are furnished. (authors)

Analysis of the pre-rift/rifte transition interval (Serraria and Barra de Itiuba formations) from the Sergipe-Alagoas basin; Analise da secao de transicao pre-rifte/rifte (formacoes Serraria e Barra de Itiuba) da Bacia Sergipe-Alagoas

Energy Technology Data Exchange (ETDEWEB)

Barreiro, C.B.; Mizusaki, A.M.P. [Rio Grande do Sul Univ., Porto Alegre, RS (Brazil)]. E-mail: camilita@terra.com.br; ana.misuzaki@ufrgs.br; Garcia, A.J.V. [Universidade do Vale do Rio dos Sinos (UNISINOS), Sao Leopoldo, RS (Brazil)]. E-mail: garcia@euler.unisinos.br

2003-07-01

The pre-rift/rift transition is represented by the Serraria and Barra de Itiuba formations. This interval was analyzed through qualitative and quantitative descriptions of cores, electric log analysis and studies of outcropping sections. The integration of surface and subsurface data allowed the stratigraphic characterization of sandstone bodies in the pre-rift/rift. These sandstones bodies were deposited by fluvial braided, lacustrine and deltaic systems (delta plain, delta front and pro delta). The sedimentary deposits characterized in the Serraria Formation are of channel, flooding of the fluvial system and eolic. The upper interval of this formation is characterized by to coarse medium-grained sandstones identified as the Caioba Sandstone. The Barra de Itiuba Formation contains lake, pro delta, frontal bar, distributary mouth, crevasse and distributary channel deposits. The sandstone units were specifically characterized in terms of their potential reservoir quality, and they were characterized the reservoirs R1 (good to medium quality) and Caioba (good quality) from the pre-rift phase, and reservoirs R2 (medium quality) and R3 (medium to good quality) from the rift phase. The reservoirs from pre-rift phase phase show the better reservoirs quality potential of the pre-rift/rift transition in the Sergipe-Alagoas Basin. (author)

Experiments and Simulations of Fluid Flow in Heterogeneous Reservoir Models - Emphasis on Impacts from Crossbeds and Fractures

Energy Technology Data Exchange (ETDEWEB)

Boerresen, Knut Arne

1996-12-31

Hydrocarbon recovery from subsurface reservoirs has become increasingly dependent on advanced recovery techniques that require improved understanding of the physics of fluid flow within and across geological units including small-scale heterogeneities and fractures. In this thesis, impacts from heterogeneities on local fluid flow are studied experimentally by means of imaging techniques to visualize fluid flow in two dimensions during flooding of larger reservoir models. Part 1 reflects the multi-disciplinary collaboration, by briefly introducing the relevant geology, the literature on experiments on fluid flow in bedded structures, and outlining the applied numerical simulator and imaging techniques applied to visualize fluid flow. The second part contains a synopsis of displacement experiments in naturally laminated sandstones and in crossbed laboratory models, and of the impact from incipient shear fractures on oil recovery. The detailed results obtained from the experiments and simulations are described in six papers, all included. 215 refs., 108 figs., 16 tabs.

Experiments and Simulations of Fluid Flow in Heterogeneous Reservoir Models - Emphasis on Impacts from Crossbeds and Fractures

Energy Technology Data Exchange (ETDEWEB)

Boerresen, Knut Arne

1997-12-31

Hydrocarbon recovery from subsurface reservoirs has become increasingly dependent on advanced recovery techniques that require improved understanding of the physics of fluid flow within and across geological units including small-scale heterogeneities and fractures. In this thesis, impacts from heterogeneities on local fluid flow are studied experimentally by means of imaging techniques to visualize fluid flow in two dimensions during flooding of larger reservoir models. Part 1 reflects the multi-disciplinary collaboration, by briefly introducing the relevant geology, the literature on experiments on fluid flow in bedded structures, and outlining the applied numerical simulator and imaging techniques applied to visualize fluid flow. The second part contains a synopsis of displacement experiments in naturally laminated sandstones and in crossbed laboratory models, and of the impact from incipient shear fractures on oil recovery. The detailed results obtained from the experiments and simulations are described in six papers, all included. 215 refs., 108 figs., 16 tabs.

Studies of electrical properties of low-resistivity sandstones based on digital rock technology

Science.gov (United States)

Yan, Weichao; Sun, Jianmeng; Zhang, Jinyan; Yuan, Weiguo; Zhang, Li; Cui, Likai; Dong, Huaimin

2018-02-01

Electrical properties are important parameters to quantitatively calculate water saturation in oil and gas reservoirs by well logging interpretation. It is usual that oil layers show high resistivity responses, while water layers show low-resistivity responses. However, there are low-resistivity oil zones that exist in many oilfields around the world, leading to difficulties for reservoir evaluation. In our research, we used digital rock technology to study different internal and external factors to account for low rock resistivity responses in oil layers. We first constructed three-dimensional digital rock models with five components based on micro-computed tomography technology and x-ray diffraction experimental results, and then oil and water distributions in pores were determined by the pore morphology method. When the resistivity of each component was assigned, rock resistivities were calculated by using the finite element method. We collected 20 sandstone samples to prove the effectiveness of our numerical simulation methods. Based on the control variate method, we studied the effects of different factors on the resistivity indexes and rock resistivities. After sensitivity analyses, we found the main factors which caused low rock resistivities in oil layers. For unfractured rocks, influential factors arranged in descending order of importance were porosity, clay content, temperature, water salinity, heavy mineral, clay type and wettability. In addition, we found that the resistivity index could not provide enough information to identify a low-resistivity oil zone by using laboratory rock-electric experimental results. These results can not only expand our understandings of the electrical properties of low-resistivity rocks from oil layers, but also help identify low-resistivity oil zones better.

Fast evolving conduits in clay-bonded sandstone: Characterization, erosion processes and significance for the origin of sandstone landforms

Czech Academy of Sciences Publication Activity Database

Bruthans, J.; Svetlik, D.; Soukup, J.; Schweigstillová, Jana; Válek, Jan; Sedláčková, M.; Mayo, A.L.

2012-01-01

Roč. 177, December (2012), s. 178-193 ISSN 0169-555X R&D Projects: GA AV ČR IAA300130806 Institutional support: RVO:67985891 ; RVO:68378297 Keywords : sandstone * erosion * piping * tensile strength * conduit * landform Subject RIV: DA - Hydrology ; Limnology Impact factor: 2.552, year: 2012

APPLICATION OF INTEGRATED RESERVOIR MANAGEMENT AND RESERVOIR CHARACTERIZATION