Improving the communication reliability of body sensor networks based on the IEEE 802.15.4 protocol.

Science.gov (United States)

Gomes, Diogo; Afonso, José A

2014-03-01

Body sensor networks (BSNs) enable continuous monitoring of patients anywhere, with minimum constraints to daily life activities. Although the IEEE 802.15.4 and ZigBee(®) (ZigBee Alliance, San Ramon, CA) standards were mainly developed for use in wireless sensors network (WSN) applications, they are also widely used in BSN applications because of device characteristics such as low power, low cost, and small form factor. However, compared with WSNs, BSNs present some very distinctive characteristics in terms of traffic and mobility patterns, heterogeneity of the nodes, and quality of service requirements. This article evaluates the suitability of the carrier sense multiple access-collision avoidance protocol, used by the IEEE 802.15.4 and ZigBee standards, for data-intensive BSN applications, through the execution of experimental tests in different evaluation scenarios, in order to take into account the effects of contention, clock drift, and hidden nodes on the communication reliability. Results show that the delivery ratio may decrease substantially during transitory periods, which can last for several minutes, to a minimum of 90% with retransmissions and 13% without retransmissions. This article also proposes and evaluates the performance of the BSN contention avoidance mechanism, which was designed to solve the identified reliability problems. This mechanism was able to restore the delivery ratio to 100% even in the scenario without retransmissions.

Maximally efficient protocols for direct secure quantum communication

Energy Technology Data Exchange (ETDEWEB)

Banerjee, Anindita [Department of Physics and Materials Science Engineering, Jaypee Institute of Information Technology, A-10, Sector-62, Noida, UP-201307 (India); Department of Physics and Center for Astroparticle Physics and Space Science, Bose Institute, Block EN, Sector V, Kolkata 700091 (India); Pathak, Anirban, E-mail: anirban.pathak@jiit.ac.in [Department of Physics and Materials Science Engineering, Jaypee Institute of Information Technology, A-10, Sector-62, Noida, UP-201307 (India); RCPTM, Joint Laboratory of Optics of Palacky University and Institute of Physics of Academy of Science of the Czech Republic, Faculty of Science, Palacky University, 17. Listopadu 12, 77146 Olomouc (Czech Republic)

2012-10-01

Two protocols for deterministic secure quantum communication (DSQC) using GHZ-like states have been proposed. It is shown that one of these protocols is maximally efficient and that can be modified to an equivalent protocol of quantum secure direct communication (QSDC). Security and efficiency of the proposed protocols are analyzed and compared. It is shown that dense coding is sufficient but not essential for DSQC and QSDC protocols. Maximally efficient QSDC protocols are shown to be more efficient than their DSQC counterparts. This additional efficiency arises at the cost of message transmission rate. -- Highlights: ► Two protocols for deterministic secure quantum communication (DSQC) are proposed. ► One of the above protocols is maximally efficient. ► It is modified to an equivalent protocol of quantum secure direct communication (QSDC). ► It is shown that dense coding is sufficient but not essential for DSQC and QSDC protocols. ► Efficient QSDC protocols are always more efficient than their DSQC counterparts.

A Hierarchical Energy Efficient Reliable Transport Protocol for Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Prabhudutta Mohanty

2014-12-01

Full Text Available The two important requirements for many Wireless Senor Networks (WSNs are prolonged network lifetime and end-to-end reliability. The sensor nodes consume more energy during data transmission than the data sensing. In WSN, the redundant data increase the energy consumption, latency and reduce reliability during data transmission. Therefore, it is important to support energy efficient reliable data transport in WSNs. In this paper, we present a Hierarchical Energy Efficient Reliable Transport Protocol (HEERTP for the data transmission within the WSN. This protocol maximises the network lifetime by controlling the redundant data transmission with the co-ordination of Base Station (BS. The proposed protocol also achieves end-to-end reliability using a hop-by-hop acknowledgement scheme. We evaluate the performance of the proposed protocol through simulation. The simulation results reveal that our proposed protocol achieves better performance in terms of energy efficiency, latency and reliability than the existing protocols.

Development of IT-based Data Communication Protocol for Nuclear Power Plant

International Nuclear Information System (INIS)

Jeong, K. I.; Kim, D. H.; Lee, J. C.

2009-07-01

The communication protocol, which provide overall communication rules and methods and give ways how to exchange information, is the most important part and it can affect the overall performance of communication network. Therefore, the first step of development of the communication network of an NPP is its own communication protocol design, which conforms to the requirements and characteristics of an NPP I and C. To manage the protocol development process, we establish development procedure and define detail substantive based on the procedure and we examine the adaptability of existing commercial communication protocols to the communication protocol of an NPP I and C. Existing commercial communication protocols based on Information Technology(IT) can be categorized into 3 groups: general commercial communication protocols, industrial communication protocols, military communication protocols. We analyze the design criteria and performance requirements of popular protocols in each group. And also, we examine the adaptability to the communication protocol of an NPP. Based on these results, we developed our own protocol for NPP I and C, which meet the required specifications through design overall protocol architecture and data frame format, definition of functional requirements and specifications

Research on Multioperator silk screen printer Based on Communication Protocol Macro

Directory of Open Access Journals (Sweden)

Zhiming Zhang

2018-01-01

Full Text Available Multioperator silk screen printer is automatic silk screen printing equipment. There are many advantages, such as energy saving, reduce the labor intensity and so on. The control system consists of an intermittent movement main motor and eight color working station printing cycle motion motors. The system controls nine frequency converters through protocol macro communication by using PLC. This paper studies the principle and process characteristics of multioperator silk screen printer. Besides, this paper adopts protocol macro sequence generation method for communication between PLC and frequency converter. This method can control the programming of parameters, such as frequency, operation and monitoring. It also can realize the printing of eight color working stations and monitor the printing status in real time. The practical application proves that the method meets the technical requirements and the reliability is good.

An one-time-pad key communication protocol with entanglement

OpenAIRE

Cai, Qing-yu

2003-01-01

We present an one-time-pad key communication protocol that allows secure direct communication with entanglement. Alice can send message to Bob in a deterministic manner by using local measurements and public communication. The theoretical efficiency of this protocol is double compared with BB84 protocol. We show this protocol is unconditional secure under arbitrary quantum attack. And we discuss that this protocol can be perfectly implemented with current technologies.

Protocol for Communication Networking for Formation Flying

Science.gov (United States)

Jennings, Esther; Okino, Clayton; Gao, Jay; Clare, Loren

2009-01-01

An application-layer protocol and a network architecture have been proposed for data communications among multiple autonomous spacecraft that are required to fly in a precise formation in order to perform scientific observations. The protocol could also be applied to other autonomous vehicles operating in formation, including robotic aircraft, robotic land vehicles, and robotic underwater vehicles. A group of spacecraft or other vehicles to which the protocol applies could be characterized as a precision-formation- flying (PFF) network, and each vehicle could be characterized as a node in the PFF network. In order to support precise formation flying, it would be necessary to establish a corresponding communication network, through which the vehicles could exchange position and orientation data and formation-control commands. The communication network must enable communication during early phases of a mission, when little positional knowledge is available. Particularly during early mission phases, the distances among vehicles may be so large that communication could be achieved only by relaying across multiple links. The large distances and need for omnidirectional coverage would limit communication links to operation at low bandwidth during these mission phases. Once the vehicles were in formation and distances were shorter, the communication network would be required to provide high-bandwidth, low-jitter service to support tight formation-control loops. The proposed protocol and architecture, intended to satisfy the aforementioned and other requirements, are based on a standard layered-reference-model concept. The proposed application protocol would be used in conjunction with conventional network, data-link, and physical-layer protocols. The proposed protocol includes the ubiquitous Institute of Electrical and Electronics Engineers (IEEE) 802.11 medium access control (MAC) protocol to be used in the datalink layer. In addition to its widespread and proven use in

Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs

Directory of Open Access Journals (Sweden)

Woo-Yong Choi

2009-01-01

Full Text Available We propose the efficient reliable multicast MAC protocol based on the connectivity information among the recipients. Enhancing the BMMM (Batch Mode Multicast MAC protocol, the reliable multicast MAC protocol significantly reduces the RAK (Request for ACK frame transmissions in a reasonable computational time and enhances the MAC performance. By the analytical performance analysis, the throughputs of the BMMM protocol and our proposed MAC protocol are derived. Numerical examples show that our proposed MAC protocol increases the reliable multicast MAC performance for IEEE 802.11 wireless LANs.

Quantum Communication Attacks on Classical Cryptographic Protocols

DEFF Research Database (Denmark)

Damgård, Ivan Bjerre

, one can show that the protocol remains secure even under such an attack. However, there are also cases where the honest players are quantum as well, even if the protocol uses classical communication. For instance, this is the case when classical multiparty computation is used as a “subroutine......In the literature on cryptographic protocols, it has been studied several times what happens if a classical protocol is attacked by a quantum adversary. Usually, this is taken to mean that the adversary runs a quantum algorithm, but communicates classically with the honest players. In several cases......” in quantum multiparty computation. Furthermore, in the future, players in a protocol may employ quantum computing simply to improve efficiency of their local computation, even if the communication is supposed to be classical. In such cases, it no longer seems clear that a quantum adversary must be limited...

Quantum Communication Attacks on Classical Cryptographic Protocols

DEFF Research Database (Denmark)

Damgård, Ivan Bjerre

, one can show that the protocol remains secure even under such an attack. However, there are also cases where the honest players are quantum as well, even if the protocol uses classical communication. For instance, this is the case when classical multiparty computation is used as a “subroutine......” in quantum multiparty computation. Furthermore, in the future, players in a protocol may employ quantum computing simply to improve efficiency of their local computation, even if the communication is supposed to be classical. In such cases, it no longer seems clear that a quantum adversary must be limited......In the literature on cryptographic protocols, it has been studied several times what happens if a classical protocol is attacked by a quantum adversary. Usually, this is taken to mean that the adversary runs a quantum algorithm, but communicates classically with the honest players. In several cases...

Cognitive Communications Protocols for SATCOM

Science.gov (United States)

2017-10-20

communications protocols for satellite and space communications with possible broad applications in defense, homeland-security as well as consumer ...communications with possible broad applications in defense, homeland-security, and civilian as well as consumer telecommunications. Such cognitive...vulnerable against smart jammers that may attempt to learn the cognitive radios own behavior . In response, our second class of proposed algorithms

Feasible quantum communication complexity protocol

International Nuclear Information System (INIS)

Galvao, Ernesto F.

2002-01-01

I show that a simple multiparty communication task can be performed more efficiently with quantum communication than with classical communication, even with low detection efficiency η. The task is a communication complexity problem in which distant parties need to compute a function of the distributed inputs, while minimizing the amount of communication between them. A realistic quantum optical setup is suggested that can demonstrate a five-party quantum protocol with higher-than-classical performance, provided η>0.33

Mac protocols for cyber-physical systems

CERN Document Server

Xia, Feng

2015-01-01

This book provides a literature review of various wireless MAC protocols and techniques for achieving real-time and reliable communications in the context of cyber-physical systems (CPS). The evaluation analysis of IEEE 802.15.4 for CPS therein will give insights into configuration and optimization of critical design parameters of MAC protocols. In addition, this book also presents the design and evaluation of an adaptive MAC protocol for medical CPS, which exemplifies how to facilitate real-time and reliable communications in CPS by exploiting IEEE 802.15.4 based MAC protocols. This book wil

Semi-quantum communication: protocols for key agreement, controlled secure direct communication and dialogue

Science.gov (United States)

Shukla, Chitra; Thapliyal, Kishore; Pathak, Anirban

2017-12-01

Semi-quantum protocols that allow some of the users to remain classical are proposed for a large class of problems associated with secure communication and secure multiparty computation. Specifically, first-time semi-quantum protocols are proposed for key agreement, controlled deterministic secure communication and dialogue, and it is shown that the semi-quantum protocols for controlled deterministic secure communication and dialogue can be reduced to semi-quantum protocols for e-commerce and private comparison (socialist millionaire problem), respectively. Complementing with the earlier proposed semi-quantum schemes for key distribution, secret sharing and deterministic secure communication, set of schemes proposed here and subsequent discussions have established that almost every secure communication and computation tasks that can be performed using fully quantum protocols can also be performed in semi-quantum manner. Some of the proposed schemes are completely orthogonal-state-based, and thus, fundamentally different from the existing semi-quantum schemes that are conjugate coding-based. Security, efficiency and applicability of the proposed schemes have been discussed with appropriate importance.

Deterministic secure communication protocol without using entanglement

OpenAIRE

Cai, Qing-yu

2003-01-01

We show a deterministic secure direct communication protocol using single qubit in mixed state. The security of this protocol is based on the security proof of BB84 protocol. It can be realized with current technologies.

Cryptanalysis and improvement of quantum secure communication network protocol with entangled photons for mobile communications

International Nuclear Information System (INIS)

Gao, Gan

2014-01-01

Recently, a communication protocol called controlled bidirectional quantum secret direct communication for mobile networks was proposed by Chou et al (2014 Mobile Netw. Appl. 19 121). We study the security of the proposed communication protocol and find that it is not secure. The controller, Telecom Company, may eavesdrop secret messages from mobile devices without being detected. Finally, we give a possible improvement of the communication protocol. (paper)

Securing statically-verified communications protocols against timing attacks

DEFF Research Database (Denmark)

Buchholtz, Mikael; Gilmore, Stephen; Hillston, Jane

2004-01-01

We present a federated analysis of communication protocols which considers both security properties and timing. These are not entirely independent observations of a protocol; by using timing observations of an executing protocol it is possible to deduce derived information about the nature...... of the communication even in the presence of unbreakable encryption. Our analysis is based on expressing the protocol as a process algebra model and deriving from this process models analysable by the Imperial PEPA Compiler and the LySatool....

CPM Test-Retest Reliability: "Standard" vs "Single Test-Stimulus" Protocols.

Science.gov (United States)

Granovsky, Yelena; Miller-Barmak, Adi; Goldstein, Oren; Sprecher, Elliot; Yarnitsky, David

2016-03-01

Assessment of pain inhibitory mechanisms using conditioned pain modulation (CPM) is relevant clinically in prediction of pain and analgesic efficacy. Our objective is to provide necessary estimates of intersession CPM reliability, to enable transformation of the CPM paradigm into a clinical tool. Two cohorts of young healthy subjects (N = 65) participated in two dual-session studies. In Study I, a Bath-Thermode CPM protocol was used, with hot water immersion and contact heat as conditioning- and test-stimuli, respectively, in a classical parallel CPM design introducing test-stimulus first, and then the conditioning- and repeated test-stimuli in parallel. Study II consisted of two CPM protocols: 1) Two-Thermodes, one for each of the stimuli, in the same parallel design as above, and 2) single test-stimulus (STS) protocol with a single administration of a contact heat test-stimulus, partially overlapped in time by a remote shorter contact heat as conditioning stimulus. Test-retest reliability was assessed within 3-7 days. The STS-CPM had superior reliability intraclass correlation (ICC 2 ,: 1  = 0.59) over Bath-Thermode (ICC 2 ,: 1  = 0.34) or Two-Thermodes (ICC 2 ,: 1  = 0.21) protocols. The hand immersion conditioning pain had higher reliability than thermode pain (ICC 2 ,: 1  = 0.76 vs ICC 2 ,: 1  = 0.16). Conditioned test-stimulus pain scores were of good (ICC 2 ,: 1  = 0.62) or fair (ICC 2 ,: 1  = 0.43) reliability for the Bath-Thermode and the STS, respectively, but not for the Two-Thermodes protocol (ICC 2 ,: 1  = 0.20). The newly developed STS-CPM paradigm was more reliable than other CPM protocols tested here, and should be further investigated for its clinical relevance. It appears that large contact size of the conditioning-stimulus and use of single rather than dual test-stimulus pain contribute to augmentation of CPM reliability. © 2015 American Academy of Pain Medicine. All rights reserved. For permissions, please e

Towards Reliable Integrated Services for Dependable Systems

DEFF Research Database (Denmark)

Schiøler, Henrik; Ravn, Anders Peter; Izadi-Zamanabadi, Roozbeh

Reliability issues for various technical systems are discussed and focus is directed towards distributed systems, where communication facilities are vital to maintain system functionality. Reliability in communication subsystems is considered as a resource to be shared among a number of logical c...... applications residing on alternative routes. Details are provided for the operation of RRRSVP based on reliability slack calculus. Conclusions summarize the considerations and give directions for future research....... connections and a reliability management framework is suggested. We suggest a network layer level reliability management protocol RRSVP (Reliability Resource Reservation Protocol) as a counterpart of the RSVP for bandwidth and time resource management. Active and passive standby redundancy by background...

Towards Reliable Integrated Services for Dependable Systems

DEFF Research Database (Denmark)

Schiøler, Henrik; Ravn, Anders Peter; Izadi-Zamanabadi, Roozbeh

2003-01-01

Reliability issues for various technical systems are discussed and focus is directed towards distributed systems, where communication facilities are vital to maintain system functionality. Reliability in communication subsystems is considered as a resource to be shared among a number of logical c...... applications residing on alternative routes. Details are provided for the operation of RRRSVP based on reliability slack calculus. Conclusions summarize the considerations and give directions for future research....... connections and a reliability management framework is suggested. We suggest a network layer level reliability management protocol RRSVP (Reliability Resource Reservation Protocol) as a counterpart of the RSVP for bandwidth and time resource management. Active and passive standby redundancy by background...

An FEC Adaptive Multicast MAC Protocol for Providing Reliability in WLANs

Science.gov (United States)

Basalamah, Anas; Sato, Takuro

For wireless multicast applications like multimedia conferencing, voice over IP and video/audio streaming, a reliable transmission of packets within short delivery delay is needed. Moreover, reliability is crucial to the performance of error intolerant applications like file transfer, distributed computing, chat and whiteboard sharing. Forward Error Correction (FEC) is frequently used in wireless multicast to enhance Packet Error Rate (PER) performance, but cannot assure full reliability unless coupled with Automatic Repeat Request forming what is knows as Hybrid-ARQ. While reliable FEC can be deployed at different levels of the protocol stack, it cannot be deployed on the MAC layer of the unreliable IEEE802.11 WLAN due to its inability to exchange ACKs with multiple recipients. In this paper, we propose a Multicast MAC protocol that enhances WLAN reliability by using Adaptive FEC and study it's performance through mathematical analysis and simulation. Our results show that our protocol can deliver high reliability and throughput performance.

Eavesdropping on the two-way quantum communication protocols with invisible photons

Energy Technology Data Exchange (ETDEWEB)

Cai Qingyu [State Key Laboratory of Magnetics Resonance and Atomic and Molecular Physics, Wuhan Institution of Physics and Mathematics, Chinese Academy of Sciences, Wuhan 430071 (China)]. E-mail: qycai@wipm.ac.cn

2006-02-20

The crucial issue of quantum communication protocol is its security. In this Letter, we show that all the deterministic and direct two-way quantum communication protocols, sometimes called ping-pong (PP) protocols, are insecure when an eavesdropper uses the invisible photon to eavesdrop on the communication. With our invisible photon eavesdropping (IPE) scheme, the eavesdropper can obtain full information of the communication with zero risk of being detected. We show that this IPE scheme can be implemented experimentally with current technology. Finally, a possible improvement of PP communication protocols security is proposed00.

Eavesdropping on the two-way quantum communication protocols with invisible photons

International Nuclear Information System (INIS)

Cai Qingyu

2006-01-01

The crucial issue of quantum communication protocol is its security. In this Letter, we show that all the deterministic and direct two-way quantum communication protocols, sometimes called ping-pong (PP) protocols, are insecure when an eavesdropper uses the invisible photon to eavesdrop on the communication. With our invisible photon eavesdropping (IPE) scheme, the eavesdropper can obtain full information of the communication with zero risk of being detected. We show that this IPE scheme can be implemented experimentally with current technology. Finally, a possible improvement of PP communication protocols security is proposed

Reliability Analysis Techniques for Communication Networks in Nuclear Power Plant

International Nuclear Information System (INIS)

Lim, T. J.; Jang, S. C.; Kang, H. G.; Kim, M. C.; Eom, H. S.; Lee, H. J.

2006-09-01

The objectives of this project is to investigate and study existing reliability analysis techniques for communication networks in order to develop reliability analysis models for nuclear power plant's safety-critical networks. It is necessary to make a comprehensive survey of current methodologies for communication network reliability. Major outputs of this study are design characteristics of safety-critical communication networks, efficient algorithms for quantifying reliability of communication networks, and preliminary models for assessing reliability of safety-critical communication networks

On consensus through communication without a commonly known protocol

OpenAIRE

Tsakas Elias; Voorneveld Mark

2010-01-01

The present paper extends the standard model of pairwise communication among Bayesianagents to cases where the structure of the communication protocol is not commonly known.We show that, even under strict conditions on the structure of the protocols and the nature of the transmitted signals, a consensus may never be reached if very little asymmetric information about the protocol is introduced.

A Review of Communications Protocol for Intelligent Remote Terminal Unit Development

Directory of Open Access Journals (Sweden)

Mohd Ruddin Ab. Ghani

2013-11-01

Full Text Available This paper reviewed all the possible interfacing communication protocols for remote terminal unit (RTU. Supervisory Control and Data Acquisition (SCADA system is a central station that can communicate with other network using the protocol. Fundamentally, the architectures of all networks are based on the seven layers of open system interconnection (OSI and International Standard Organization (ISO. The objective of designing the protocols is to check the status of all the input and output field devices and send the report according to that status. The corresponding protocol and communication parameters between the connecting devices will be included in designing a complex SCADA system. The available protocols to develop the communication of RTU are Modbus/ASCII, distributed network protocol (DNP3, controller area network (CAN, International Electro-technical Commission (IEC 60870, transmission control protocol/internet protocol (TCP/IP.

MODELLING AND VERIFICATION OF KITSAT PACKET COMMUNICATION PROTOCOLS

Directory of Open Access Journals (Sweden)

Young-Ro Lee

1996-06-01

Full Text Available In this paper, in order to verify KITSAT 1/2 packet communication protocols, we model the AX.25 protocol and PACSAT protocol by using an extended Petri net and then verify the correctness, boundedness, liveness and deadlock freeness of packet protocols by utilizing reachability trees.

Database communication protocol analyses and security detection

International Nuclear Information System (INIS)

Luo Qun; Liu Qiushi

2003-01-01

In this paper we introduced the analysis of TDS protocol in the communication application between Client and Server about SYBASE and MICROSOFT SQL SERVER and do some test for some bugs existed in the protocol. (authors)

Taking the Politics Out of Satellite and Space-Based Communications Protocols

Science.gov (United States)

Ivancic, William D.

2006-01-01

After many years of studies, experimentation, and deployment, large amounts of misinformation and misconceptions remain regarding applicability of various communications protocols for use in satellite and space-based networks. This paper attempts to remove much of the politics, misconceptions, and misinformation that have plagued spacebased communications protocol development and deployment. This paper provides a common vocabulary for communications; a general discussion of the requirements for various communication environments; an evaluation of tradeoffs between circuit and packet-switching technologies, and the pros and cons of various link, network, transport, application, and security protocols. Included is the applicability of protocol enhancing proxies to NASA, Department of Defense (DOD), and commercial space communication systems.

Design and Implementation of a MAC Protocol for Timely and Reliable Delivery of Command and Data in Dynamic Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Phan Van Vinh

2013-09-01

Full Text Available This paper proposes and implements a new TDMA-based MAC protocol for providing timely and reliable delivery of data and command for monitoring and control networks. In this kind of network, sensor nodes are required to sense data from the monitoring environment periodically and then send the data to a sink. The sink determines whether the environment is safe or not by analyzing the acquired data. Sometimes, a command or control message is sent from the sink to a particular node or a group of nodes to execute the services or request further interested data. The proposed MAC protocol enables bidirectional communication, controls active and sleep modes of a sensor node to conserve energy, and addresses the problem of load unbalancing between the nodes near a sink and the other nodes. It can improve reliability of communication significantly while extending network lifetime. These claims are supported by the experimental results.

Network Coding Protocols for Smart Grid Communications

DEFF Research Database (Denmark)

Prior, Rui; Roetter, Daniel Enrique Lucani; Phulpin, Yannick

2014-01-01

We propose a robust network coding protocol for enhancing the reliability and speed of data gathering in smart grids. At the heart of our protocol lies the idea of tunable sparse network coding, which adopts the transmission of sparsely coded packets at the beginning of the transmission process b...

Overview of the InterGroup protocols

Energy Technology Data Exchange (ETDEWEB)

Berket, Karlo [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Agarwal, Deborah A. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Melliar-Smith, P. Michael [Univ. of California, Santa Barbara, CA (United States); Moser, Louise E. [Univ. of California, Santa Barbara, CA (United States)

2001-03-01

Existing reliable ordered group communication protocols have been developed for local-area networks and do not, in general, scale well to large numbers of nodes and wide-area networks. The InterGroup suite of protocols is a scalable group communication system that introduces a novel approach to handling group membership, and supports a receiver-oriented selection of service. The protocols are intended for a wide-area network, with a large number of nodes, that has highly variable delays and a high message loss rate, such as the Internet. The levels of the message delivery service range from unreliable unordered to reliable group timestamp ordered.

An Energy-Efficient Link Layer Protocol for Reliable Transmission over Wireless Networks

Directory of Open Access Journals (Sweden)

Iqbal Adnan

2009-01-01

Full Text Available In multihop wireless networks, hop-by-hop reliability is generally achieved through positive acknowledgments at the MAC layer. However, positive acknowledgments introduce significant energy inefficiencies on battery-constrained devices. This inefficiency becomes particularly significant on high error rate channels. We propose to reduce the energy consumption during retransmissions using a novel protocol that localizes bit-errors at the MAC layer. The proposed protocol, referred to as Selective Retransmission using Virtual Fragmentation (SRVF, requires simple modifications to the positive-ACK-based reliability mechanism but provides substantial improvements in energy efficiency. The main premise of the protocol is to localize bit-errors by performing partial checksums on disjoint parts or virtual fragments of a packet. In case of error, only the corrupted virtual fragments are retransmitted. We develop stochastic models of the Simple Positive-ACK-based reliability, the previously-proposed Packet Length Optimization (PLO protocol, and the SRVF protocol operating over an arbitrary-order Markov wireless channel. Our analytical models show that SRVF provides significant theoretical improvements in energy efficiency over existing protocols. We then use bit-error traces collected over different real networks to empirically compare the proposed and existing protocols. These experimental results further substantiate that SRVF provides considerably better energy efficiency than Simple Positive-ACK and Packet Length Optimization protocols.

Shoulder muscle endurance: the development of a standardized and reliable protocol

Directory of Open Access Journals (Sweden)

Roy Jean-Sébastien

2011-01-01

Full Text Available Abstract Background Shoulder muscle fatigue has been proposed as a possible link to explain the association between repetitive arm use and the development of rotator cuff disorders. To our knowledge, no standardized clinical endurance protocol has been developed to evaluate the effects of muscle fatigue on shoulder function. Such a test could improve clinical examination of individuals with shoulder disorders. Therefore, the purpose of this study was to establish a reliable protocol for objective assessment of shoulder muscle endurance. Methods An endurance protocol was developed on a stationary dynamometer (Biodex System 3. The endurance protocol was performed in isotonic mode with the resistance set at 50% of each subject's peak torque as measured for shoulder external (ER and internal rotation (IR. Each subject performed 60 continuous repetitions of IR/ER rotation. The endurance protocol was performed by 36 healthy individuals on two separate occasions at least two days apart. Maximal isometric shoulder strength tests were performed before and after the fatigue protocol to evaluate the effects of the endurance protocol and its reliability. Paired t-tests were used to evaluate the reduction in shoulder strength due to the protocol, while intraclass correlation coefficients (ICC and minimal detectable change (MDC were used to evaluate its reliability. Results Maximal isometric strength was significantly decreased after the endurance protocol (P 0.84. Conclusions Changes in muscular performance observed during and after the muscular endurance protocol suggests that the protocol did result in muscular fatigue. Furthermore, this study established that the resultant effects of fatigue of the proposed isotonic protocol were reproducible over time. The protocol was performed without difficulty by all volunteers and took less than 10 minutes to perform, suggesting that it might be feasible for clinical practice. This protocol could be used to induce

Ultra-Reliable Communication in a Factory Environment for 5G Wireless Networks

DEFF Research Database (Denmark)

Singh, Bikramjit; Lee, Zexian; Tirkkonen, Olav

2016-01-01

The focus of this paper on mission-critical Communications in a 5G cellular communication system. Technologies to provide ultra-reliable communication, with 99:999 % availability in a factory environment are studied. We have analysed the feasibility requirements for ultra-reliable communication...... are compared. Last, the importance of multi-hop communication and multi-point coordination schemes are highlighted to improve the reliable communication in presence of interference and clutter. Keywords—5G; mission-critical communications; ultra-reliable communication; availability; reliability...

Ultra-Reliable Communication in 5G Wireless Systems

DEFF Research Database (Denmark)

Popovski, Petar

2014-01-01

—Wireless 5G systems will not only be “4G, but faster”. One of the novel features discussed in relation to 5G is Ultra-Reliable Communication (URC), an operation mode not present in today’s wireless systems. URC refers to provision of certain level of communication service almost 100 % of the time....... Example URC applications include reliable cloud connectivity, critical connections for industrial automation and reliable wireless coordination among vehicles. This paper puts forward a systematic view on URC in 5G wireless systems. It starts by analyzing the fundamental mechanisms that constitute......-term URC (URC-S). The second dimension is represented by the type of reliability impairment that can affect the communication reliability in a given scenario. The main objective of this paper is to create the context for defining and solving the new engineering problems posed by URC in 5G....

Wireless Channel Modeling Perspectives for Ultra-Reliable Communications

DEFF Research Database (Denmark)

Eggers, Patrick Claus F.; Popovski, Petar

2018-01-01

Ultra-Reliable Communication (URC) is one of the distinctive features of the upcoming 5G wireless communication. The level of reliability, going down to packet error rates (PER) of $10^{-9}$, should be sufficiently convincing in order to remove cables in an industrial setting or provide remote co...

Design of Bus Protocol Intelligent Initiation System Based On RS485

Directory of Open Access Journals (Sweden)

Li Liming

2017-01-01

Full Text Available In order to design an effective and reliable RS485 bus protocol based on RS485 bus, this paper introduces the structure and transmission mode of the command frame and the response frame, and also introduce four control measures and the communication in order to process quality of this system. The communication protocol is open, tolerant, reliable and fast, and can realize ignition more reliable and accurate in the intelligent initiation system.

Interoperability and Reliability of Multiplatform MPLS VPN: Comparison of Traffic Engineering with RSVP-TE Protocol and LDP Protocol

Directory of Open Access Journals (Sweden)

Nanang Ismail

2017-10-01

48% of packet loss per 100 sent packets while on RSVP packet loss percentage is 35.5% per 100 sent packets. Both protocols have interoperability on the third layer of multiplatform MPLS VPN, but on heavy loaded traffic condition, RSVP protocol has better reliability than the LDP protocol.

Analysis of NASA communications (Nascom) II network protocols and performance

Science.gov (United States)

Omidyar, Guy C.; Butler, Thomas E.

1991-01-01

The NASA Communications (Nascom) Division of the Mission Operations and Data Systems Directorate is to undertake a major initiative to develop the Nascom II (NII) network to achieve its long-range service objectives for operational data transport to support the Space Station Freedom Program, the Earth Observing System, and other projects. NII is the Nascom ground communications network being developed to accommodate the operational traffic of the mid-1990s and beyond. The authors describe various baseline protocol architectures based on current and evolving technologies. They address the internetworking issues suggested for reliable transfer of data over heterogeneous segments. They also describe the NII architecture, topology, system components, and services. A comparative evaluation of the current and evolving technologies was made, and suggestions for further study are described. It is shown that the direction of the NII configuration and the subsystem component design will clearly depend on the advances made in the area of broadband integrated services.

New Communication Network Protocol for a Data Acquisition System

Science.gov (United States)

Uchida, T.; Fujii, H.; Nagasaka, Y.; Tanaka, M.

2006-02-01

An event builder based on communication networks has been used in high-energy physics experiments, and various networks have been adopted, for example, IEEE 802.3 (Ethernet), asynchronous transfer mode (ATM), and so on. In particular, Ethernet is widely used because its infrastructure is very cost effective. Many systems adopt standard protocols that are designed for a general network. However, in the case of an event builder, the communication pattern between stations is different from that in a general network. The unique communication pattern causes congestion, and thus makes it difficulty to quantitatively design the network. To solve this problem, we have developed a simple network protocol for a data acquisition (DAQ) system. The protocol is designed to keep the sequence of senders so that no congestion occurs. We implemented the protocol on a small hardware component [a field programmable gate array (FPGA)] and measured the performance, so that it will be ready for a generic DAQ system

On the Effect of Security and Communication Factors in the Reliability of Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Damian Rusinek

2014-03-01

Full Text Available The ensuring reliability of wireless sensor networks (WSN is one of most important problems to be solved. In this article, the influence of the security and communication factors in the reliability of Wireless Sensor Networks was analyzed. Balancing security against performance in WSN is another issue to be solved. These factors should be considered during security analysis of quality of protection of realized protocol. In the article, we analyze wireless sensor network where hierarchical topologies is implemented with high performance routing sensors that forward big amount of data. We present the experiment results which were performed by high-performance Imote2 sensor platform and TinyOS operating system.

A two-step quantum secure direct communication protocol with hyperentanglement

International Nuclear Information System (INIS)

Gu Bin; Zhang Cheng-Yi; Huang Yu-Gai; Fang Xia

2011-01-01

We propose a two-step quantum secure direct communication (QSDC) protocol with hyperentanglement in both the spatial-mode and the polarization degrees of freedom of photon pairs which can in principle be produced with a beta barium borate crystal. The secret message can be encoded on the photon pairs with unitary operations in these two degrees of freedom independently. This QSDC protocol has a higher capacity than the original two-step QSDC protocol as each photon pair can carry 4 bits of information. Compared with the QSDC protocol based on hyperdense coding, this QSDC protocol has the immunity to Trojan horse attack strategies with the process for determining the number of the photons in each quantum signal as it is a one-way quantum communication protocol. (general)

Reliability and Validity of the Dyadic Observed Communication Scale (DOCS).

Science.gov (United States)

Hadley, Wendy; Stewart, Angela; Hunter, Heather L; Affleck, Katelyn; Donenberg, Geri; Diclemente, Ralph; Brown, Larry K

2013-02-01

We evaluated the reliability and validity of the Dyadic Observed Communication Scale (DOCS) coding scheme, which was developed to capture a range of communication components between parents and adolescents. Adolescents and their caregivers were recruited from mental health facilities for participation in a large, multi-site family-based HIV prevention intervention study. Seventy-one dyads were randomly selected from the larger study sample and coded using the DOCS at baseline. Preliminary validity and reliability of the DOCS was examined using various methods, such as comparing results to self-report measures and examining interrater reliability. Results suggest that the DOCS is a reliable and valid measure of observed communication among parent-adolescent dyads that captures both verbal and nonverbal communication behaviors that are typical intervention targets. The DOCS is a viable coding scheme for use by researchers and clinicians examining parent-adolescent communication. Coders can be trained to reliably capture individual and dyadic components of communication for parents and adolescents and this complex information can be obtained relatively quickly.

SPP: A data base processor data communications protocol

Science.gov (United States)

Fishwick, P. A.

1983-01-01

The design and implementation of a data communications protocol for the Intel Data Base Processor (DBP) is defined. The protocol is termed SPP (Service Port Protocol) since it enables data transfer between the host computer and the DBP service port. The protocol implementation is extensible in that it is explicitly layered and the protocol functionality is hierarchically organized. Extensive trace and performance capabilities have been supplied with the protocol software to permit optional efficient monitoring of the data transfer between the host and the Intel data base processor. Machine independence was considered to be an important attribute during the design and implementation of SPP. The protocol source is fully commented and is included in Appendix A of this report.

High reliable and Real-time Data Communication Network Technology for Nuclear Power Plant

International Nuclear Information System (INIS)

Jeong, K. I.; Lee, J. K.; Choi, Y. R.; Lee, J. C.; Choi, Y. S.; Cho, J. W.; Hong, S. B.; Jung, J. E.; Koo, I. S.

2008-03-01

As advanced digital Instrumentation and Control (I and C) system of NPP(Nuclear Power Plant) are being introduced to replace analog systems, a Data Communication Network(DCN) is becoming the important system for transmitting the data generated by I and C systems in NPP. In order to apply the DCNs to NPP I and C design, DCNs should conform to applicable acceptance criteria and meet the reliability and safety goals of the system. As response time is impacted by the selected protocol, network topology, network performance, and the network configuration of I and C system, DCNs should transmit a data within time constraints and response time required by I and C systems to satisfy response time requirements of I and C system. To meet these requirements, the DCNs of NPP I and C should be a high reliable and real-time system. With respect to high reliable and real-time system, several reports and techniques having influences upon the reliability and real-time requirements of DCNs are surveyed and analyzed

Eavesdropping on the Bostroem-Filbinger Communication Protocol in Noisy Quantum Channel

OpenAIRE

Cai, Qing-yu

2004-01-01

We show an eavesdropping scheme on Bostr\\UNICODE{0xf6}m-Felbinger communication protocol (called ping-pong protocol) [Phys. Rev. Lett. 89, 187902 (2002)] in an ideal quantum channel. A measurement attack can be perfectly used to eavesdrop Alice's information instead of a most general quantum operation attack. In a noisy quantum channel, the direct communication is forbidden. We present a quantum key distribution protocol based on the ping-pong protocol, which can be used in a low noisy quantu...

Some Protocols For Optical-Fiber Digital Communications

Science.gov (United States)

Yeh, Cavour; Gerla, Mario

1989-01-01

One works best in heavy traffic, another, in light traffic. Three protocols proposed for digital communications among stations connected by passive taps to pair of uni-directional optical-fiber buses. Mediate round-robin, bounded-delay access to buses by all stations and particularly suited to fast transmission. Partly because transmission medium passive (no relay stations) and partly because protocols distribute control of network among all stations with provision for addition and deletion of stations (no control stations), communication network able to resist and recover from failures. Implicit token propagates in one direction on one bus and in opposite direction on other bus, minimizing interval of silence between end of one round and beginning of next.

Is gait variability reliable in older adults and Parkinson's disease? Towards an optimal testing protocol.

Science.gov (United States)

Galna, Brook; Lord, Sue; Rochester, Lynn

2013-04-01

Despite the widespread use of gait variability in research and clinical studies, testing protocols designed to optimise its reliability have not been established. This study evaluates the impact of testing protocol and pathology on the reliability of gait variability. To (i) estimate the reliability of gait variability during continuous and intermittent walking protocols in older adults and people with Parkinson's disease (PD), (ii) determine optimal number of steps for acceptable levels of reliability of gait variability and (iii) provide sample size estimates for use in clinical trials. Gait variability was measured twice, one week apart, in 27 older adults and 25 PD participants. Participants walked at their preferred pace during: (i) a continuous 2 min walk and (ii) 3 intermittent walks over a 12 m walkway. Gait variability was calculated as the within-person standard deviation for step velocity, length and width, and step, stance and swing duration. Reliability of gait variability ranged from poor to excellent (intra class correlations .041-.860; relative limits of agreement 34-89%). Gait variability was more reliable during continuous walks. Control and PD participants demonstrated similar reliability. Increasing the number of steps improved reliability, with most improvement seen across the first 30 steps. In this study, we identified testing protocols that improve the reliability of measuring gait variability. We recommend using a continuous walking protocol and to collect no fewer than 30 steps. Early PD does not appear to impact negatively on the reliability of gait variability. Copyright © 2012 Elsevier B.V. All rights reserved.

Localized radio frequency communication using asynchronous transfer mode protocol

Science.gov (United States)

Witzke, Edward L.; Robertson, Perry J.; Pierson, Lyndon G.

2007-08-14

A localized wireless communication system for communication between a plurality of circuit boards, and between electronic components on the circuit boards. Transceivers are located on each circuit board and electronic component. The transceivers communicate with one another over spread spectrum radio frequencies. An asynchronous transfer mode protocol controls communication flow with asynchronous transfer mode switches located on the circuit boards.

A communication protocol for mobile satellite systems affected by rain attenuation

Science.gov (United States)

Lay, Norman; Dessouky, Khaled

1992-01-01

A communication protocol is described that has been developed as part of a K/Ka-band mobile terminal breadboard system to be demonstrated through NASA's Advanced Communications Technology Satellite (ACTS) in 1993. The protocol is aimed at providing the means for enhancing link availability and continuity by supporting real-time data rate selection and changes during rain events. Particular attention is given to the system architecture; types of links, connections, and packets; the protocol procedures; and design rationales.

Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs with Extended Service Range

Science.gov (United States)

Choi, Woo-Yong

2011-11-01

In this paper, we propose the efficient reliable multicast MAC protocol by which the AP (Access Point) can transmit reliably its multicast data frames to the recipients in the AP's one-hop or two-hop transmission range. The AP uses the STAs (Stations) that are directly associated with itself as the relays for the data delivery to the remote recipients that cannot be reached directly from itself. Based on the connectivity information among the recipients, the reliable multicast MAC protocol optimizes the number of the RAK (Request for ACK) frame transmissions in a reasonable computational time. Numerical examples show that our proposed MAC protocol significantly enhances the MAC performance compared with the BMMM (Batch Mode Multicast MAC) protocol that is extended to support the recipients that are in the AP's one-hop or two-hop transmission range in IEEE 802.11 wireless LANs.

RSComPro: An Open Communication Protocol for Remote Sensing Systems

DEFF Research Database (Denmark)

Vasiljevic, Nikola; Trujillo, Juan-José

The remote sensing protocol (RSComPro) is a communication protocol, which has been developed for controlling multiple remote sensing systems simultaneously through a UDP/IP and TPC/IP network. This protocol is meant to be open to the remote sensing community. The scope is the implementation of so...

Robust against route failure using power proficient reliable routing in MANET

Directory of Open Access Journals (Sweden)

M. Malathi

2018-03-01

Full Text Available The aim of this paper was to propose a novel routing protocol for Mobile Adhoc Network communication which reduces the route failure during transmission. The proposed routing protocol uses 3 salient parameters to discover the path which ensure the reliable communication. The quality of the channel, link quality and energy level of the node are the major reasons for unintentional node failure in mobile Adhoc network. So the proposed routing protocol considers these three parameters to select the best forwarder node in the path. The reliable data communication is achieved by transmitting data via path selected by the proposed routing scheme has been proven using network simulator (NS2. Keywords: Channel quality, Link quality, Mobile Adhoc Network (MANET, Residual energy

An XML-based communication protocol for accelerator distributed controls

International Nuclear Information System (INIS)

Catani, L.

2008-01-01

This paper presents the development of XMLvRPC, an RPC-like communication protocol based, for this particular application, on the TCP/IP and XML (eXtensible Markup Language) tools built-in in LabVIEW. XML is used to format commands and data passed between client and server while socket interface for communication uses either TCP or UDP transmission protocols. This implementation extends the features of these general purpose libraries and incorporates solutions that might provide, with limited modifications, full compatibility with well established and more general communication protocol, i.e. XML-RPC, while preserving portability to different platforms supported by LabVIEW. The XMLvRPC suite of software has been equipped with specific tools for its deployment in distributed control systems as, for instance, a quasi-automatic configuration and registration of the distributed components and a simple plug-and-play approach to the installation of new services. Key feature is the management of large binary arrays that allow coding of large binary data set, e.g. raw images, more efficiently with respect to the standard XML coding

An XML-based communication protocol for accelerator distributed controls

Energy Technology Data Exchange (ETDEWEB)

Catani, L. [INFN-Roma Tor Vergata, Rome (Italy)], E-mail: luciano.catani@roma2.infn.it

2008-03-01

This paper presents the development of XMLvRPC, an RPC-like communication protocol based, for this particular application, on the TCP/IP and XML (eXtensible Markup Language) tools built-in in LabVIEW. XML is used to format commands and data passed between client and server while socket interface for communication uses either TCP or UDP transmission protocols. This implementation extends the features of these general purpose libraries and incorporates solutions that might provide, with limited modifications, full compatibility with well established and more general communication protocol, i.e. XML-RPC, while preserving portability to different platforms supported by LabVIEW. The XMLvRPC suite of software has been equipped with specific tools for its deployment in distributed control systems as, for instance, a quasi-automatic configuration and registration of the distributed components and a simple plug-and-play approach to the installation of new services. Key feature is the management of large binary arrays that allow coding of large binary data set, e.g. raw images, more efficiently with respect to the standard XML coding.

Ultra-Reliable Communications in Failure-Prone Realistic Networks

DEFF Research Database (Denmark)

Gerardino, Guillermo Andrés Pocovi; Lauridsen, Mads; Alvarez, Beatriz Soret

2016-01-01

We investigate the potential of different diversity and interference management techniques to achieve the required downlink SINR outage probability for ultra-reliable communications. The evaluation is performed in a realistic network deployment based on site-specific data from a European capital....... Micro and macroscopic diversity techniques are proved to be important enablers of ultra-reliable communications. Particularly, it is shown how a 4x4 MIMO scheme with three orders of macroscopic diversity can achieve the required SINR outage performance. Smaller gains are obtained from interference...

Design and Implementation of Secure and Reliable Communication using Optical Wireless Communication

Science.gov (United States)

Saadi, Muhammad; Bajpai, Ambar; Zhao, Yan; Sangwongngam, Paramin; Wuttisittikulkij, Lunchakorn

2014-11-01

Wireless networking intensify the tractability in the home and office environment to connect the internet without wires but at the cost of risks associated with stealing the data or threat of loading malicious code with the intention of harming the network. In this paper, we proposed a novel method of establishing a secure and reliable communication link using optical wireless communication (OWC). For security, spatial diversity based transmission using two optical transmitters is used and the reliability in the link is achieved by a newly proposed method for the construction of structured parity check matrix for binary Low Density Parity Check (LDPC) codes. Experimental results show that a successful secure and reliable link between the transmitter and the receiver can be achieved by using the proposed novel technique.

Secure Protocol for “Host — NFC Reader” Communication

Directory of Open Access Journals (Sweden)

A. O. Menshenin

2012-06-01

Full Text Available The paper presents a secure protocol for communication between host and NFC reader. The protocol protection scheme uses symmetric cipher with cyclic session key generation and provides confidentiality, integrity, end parties authentication and resistance to replay attacks. Deployment scenario in a typical electronic payment system is also presented.

A protocol for better design, application, and communication of population viability analyses.

Science.gov (United States)

Pe'er, Guy; Matsinos, Yiannis G; Johst, Karin; Franz, Kamila W; Turlure, Camille; Radchuk, Viktoriia; Malinowska, Agnieszka H; Curtis, Janelle M R; Naujokaitis-Lewis, Ilona; Wintle, Brendan A; Henle, Klaus

2013-08-01

Population viability analyses (PVAs) contribute to conservation theory, policy, and management. Most PVAs focus on single species within a given landscape and address a specific problem. This specificity often is reflected in the organization of published PVA descriptions. Many lack structure, making them difficult to understand, assess, repeat, or use for drawing generalizations across PVA studies. In an assessment comparing published PVAs and existing guidelines, we found that model selection was rarely justified; important parameters remained neglected or their implementation was described vaguely; limited details were given on parameter ranges, sensitivity analysis, and scenarios; and results were often reported too inconsistently to enable repeatability and comparability. Although many guidelines exist on how to design and implement reliable PVAs and standards exist for documenting and communicating ecological models in general, there is a lack of organized guidelines for designing, applying, and communicating PVAs that account for their diversity of structures and contents. To fill this gap, we integrated published guidelines and recommendations for PVA design and application, protocols for documenting ecological models in general and individual-based models in particular, and our collective experience in developing, applying, and reviewing PVAs. We devised a comprehensive protocol for the design, application, and communication of PVAs (DAC-PVA), which has 3 primary elements. The first defines what a useful PVA is; the second element provides a workflow for the design and application of a useful PVA and highlights important aspects that need to be considered during these processes; and the third element focuses on communication of PVAs to ensure clarity, comprehensiveness, repeatability, and comparability. Thereby, DAC-PVA should strengthen the credibility and relevance of PVAs for policy and management, and improve the capacity to generalize PVA findings

Development of a standard communication protocol for an emergency situation management in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Kim, Man Cheol, E-mail: charleskim@kaeri.re.k [Integrated Risk Assessment Center, Korea Atomic Energy Research Institute, 150, Deokjin-dong, Yuseong-gu, Daejeon 305-353 (Korea, Republic of); Park, Jinkyun; Jung, Wondea [Integrated Risk Assessment Center, Korea Atomic Energy Research Institute, 150, Deokjin-dong, Yuseong-gu, Daejeon 305-353 (Korea, Republic of); Kim, Hanjeom; Kim, Yoon Joong [YGN Nuclear Power Division Training Center, Korea Hydro and Nuclear Power Company, 517 Kyemari, Hongnong-eup, Yeongkwang-gun, Chonnam 513-880 (Korea, Republic of)

2010-06-15

Correct communication between main control room (MCR) operators is an important factor in the management of emergency situations in nuclear power plants (NPPs). For this reason, a standard communication protocol for the management of emergency situations in NPPs has been developed, with the basic direction of enhancing the safety of NPPs and the standardization of communication protocols. To validate the newly developed standard communication protocol, validation experiments with 10 licensed NPP MCR operator teams was performed. From the validation experiments, it was found that the use of the standard communication protocol required more time, but it can contribute to the enhancement of the safety of NPPs by an operators' better grasp of the safety-related parameters and a more efficient and clearer communication between NPP operators, while imposing little additional workloads on the NPP MCR operators. The standard communication protocol is expected to be used to train existing NPP MCR operators without much aversion, as well as new operators.

Implementing voice over Internet protocol in mobile ad hoc network – analysing its features regarding efficiency, reliability and security

Directory of Open Access Journals (Sweden)

Naveed Ahmed Sheikh

2014-05-01

Full Text Available Providing secure and efficient real-time voice communication in mobile ad hoc network (MANET environment is a challenging problem. Voice over Internet protocol (VoIP has originally been developed over the past two decades for infrastructure-based networks. There are strict timing constraints for acceptable quality VoIP services, in addition to registration and discovery issues in VoIP end-points. In MANETs, ad hoc nature of networks and multi-hop wireless environment with significant packet loss and delays present formidable challenges to the implementation. Providing a secure real-time VoIP service on MANET is the main design objective of this paper. The authors have successfully developed a prototype system that establishes reliable and efficient VoIP communication and provides an extremely flexible method for voice communication in MANETs. The authors’ cooperative mesh-based MANET implementation can be used for rapidly deployable VoIP communication with survivable and efficient dynamic networking using open source software.

Keyboard with Universal Communication Protocol Applied to CNC Machine

Directory of Open Access Journals (Sweden)

Mejía-Ugalde Mario

2014-04-01

Full Text Available This article describes the use of a universal communication protocol for industrial keyboard based microcontroller applied to computer numerically controlled (CNC machine. The main difference among the keyboard manufacturers is that each manufacturer has its own programming of source code, producing a different communication protocol, generating an improper interpretation of the function established. The above results in commercial industrial keyboards which are expensive and incompatible in their connection with different machines. In the present work the protocol allows to connect the designed universal keyboard and the standard keyboard of the PC at the same time, it is compatible with all the computers through the communications USB, AT or PS/2, to use in CNC machines, with extension to other machines such as robots, blowing, injection molding machines and others. The advantages of this design include its easy reprogramming, decreased costs, manipulation of various machine functions and easy expansion of entry and exit signals. The results obtained of performance tests were satisfactory, because each key has the programmed and reprogrammed facility in different ways, generating codes for different functions, depending on the application where it is required to be used.

Bidirectional Quantum Secure Direct Communication Network Protocol with Hyperentanglement

International Nuclear Information System (INIS)

Gu Bin; Chen Yulin; Huang Yugai; Fang Xia

2011-01-01

We propose a bidirectional quantum secure direct communication (QSDC) network protocol with the hyperentanglment in both the spatial-mode ad the polarization degrees of freedom of photon pairs which can in principle be produced with a beta barium borate crystal. The secret message can be encoded on the photon pairs with unitary operations in these two degrees of freedom independently. Compared with other QSDC network protocols, our QSDC network protocol has a higher capacity as each photon pair can carry 4 bits of information. Also, we discuss the security of our QSDC network protocol and its feasibility with current techniques. (general)

Criteria for Evaluating Alternative Network and Link Layer Protocols for the NASA Constellation Program Communication Architecture

Science.gov (United States)

Benbenek, Daniel; Soloff, Jason; Lieb, Erica

2010-01-01

Selecting a communications and network architecture for future manned space flight requires an evaluation of the varying goals and objectives of the program, development of communications and network architecture evaluation criteria, and assessment of critical architecture trades. This paper uses Cx Program proposed exploration activities as a guideline; lunar sortie, outpost, Mars, and flexible path options are described. A set of proposed communications network architecture criteria are proposed and described. They include: interoperability, security, reliability, and ease of automating topology changes. Finally a key set of architecture options are traded including (1) multiplexing data at a common network layer vs. at the data link layer, (2) implementing multiple network layers vs. a single network layer, and (3) the use of a particular network layer protocol, primarily IPv6 vs. Delay Tolerant Networking (DTN). In summary, the protocol options are evaluated against the proposed exploration activities and their relative performance with respect to the criteria are assessed. An architectural approach which includes (a) the capability of multiplexing at both the network layer and the data link layer and (b) a single network layer for operations at each program phase, as these solutions are best suited to respond to the widest array of program needs and meet each of the evaluation criteria.

A Protocol for Content-Based Communication in Disconnected Mobile Ad Hoc Networks

Directory of Open Access Journals (Sweden)

Julien Haillot

2010-01-01

Full Text Available In content-based communication, information flows towards interested hosts rather than towards specifically set destinations. This new style of communication perfectly fits the needs of applications dedicated to information sharing, news distribution, service advertisement and discovery, etc. In this paper we address the problem of supporting content-based communication in partially or intermittently connected mobile ad hoc networks (MANETs. The protocol we designed leverages on the concepts of opportunistic networking and delay-tolerant networking in order to account for the absence of end-to-end connectivity in disconnected MANETs. The paper provides an overview of the protocol, as well as simulation results that show how this protocol can perform in realistic conditions.

Efficient Communication Protocols for Deciding Edit Distance

DEFF Research Database (Denmark)

Jowhari, Hossein

2012-01-01

In this paper we present two communication protocols on computing edit distance. In our first result, we give a one-way protocol for the following Document Exchange problem. Namely given x ∈ Σn to Alice and y ∈ Σn to Bob and integer k to both, Alice sends a message to Bob so that he learns x...... or truthfully reports that the edit distance between x and y is greater than k. For this problem, we give a randomized protocol in which Alice transmits at most O ˜ (klog 2 n) bits and each party’s time complexity is O ˜ (nlogn+k 2 log 2 n) . Our second result is a simultaneous protocol for edit distance over...... permutations. Here Alice and Bob both send a message to a third party (the referee) who does not have access to the input strings. Given the messages, the referee decides if the edit distance between x and y is at most k or not. For this problem we give a protocol in which Alice and Bob run a O...

A cross-layer communication framework for wireless networked control systems

NARCIS (Netherlands)

Israr, N.; Scanlon, W.G.; Irwin, G.W.

2009-01-01

This paper presents a robust, dynamic cross-layer wireless communication architecture for wireless networked control systems. Each layer in the proposed protocol architecture contributes to the overall goal of reliable, energy efficient communication. The protocol stack also features a

Communication Facilities for Distributed Systems

Directory of Open Access Journals (Sweden)

V. Barladeanu

1997-01-01

Full Text Available The design of physical networks and communication protocols in Distributed Systems can have a direct impact on system efficiency and reliability. This paper tries to identify efficient mechanisms and paradigms for communication in distributed systems.

Eavesdropping on the "ping-pong" quantum communication protocol

OpenAIRE

Wojcik, Antoni

2002-01-01

The proposed eavesdropping scheme reveals that the quantum communication protocol recently presented by Bostrom and Felbinger [Phys. Rev. Lett. 89, 187902 (2002)] is not secure as far as quantum channel losses are taken into account.

Optimized Interface Diversity for Ultra-Reliable Low Latency Communication (URLLC)

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Liu, Rongkuan; Popovski, Petar

2017-01-01

An important ingredient of the future 5G systems will be Ultra-Reliable Low-Latency Communication (URLLC). A way to offer URLLC without intervention in the baseband/PHY layer design is to use interface diversity and integrate multiple communication interfaces, each interface based on a different...... technology. Our approach is to use rateless codes to seamlessly distribute coded payload and redundancy data across multiple available communication interfaces. We formulate an optimization problem to find the payload allocation weights that maximize the reliability at specific target latency values...

Analysis of Security Protocols by Annotations

DEFF Research Database (Denmark)

Gao, Han

. The development of formal techniques, e.g. control flow analyses, that can check various security properties, is an important tool to meet this challenge. This dissertation contributes to the development of such techniques. In this dissertation, security protocols are modelled in the process calculus LYSA......The trend in Information Technology is that distributed systems and networks are becoming increasingly important, as most of the services and opportunities that characterise the modern society are based on these technologies. Communication among agents over networks has therefore acquired a great...... deal of research interest. In order to provide effective and reliable means of communication, more and more communication protocols are invented, and for most of them, security is a significant goal. It has long been a challenge to determine conclusively whether a given protocol is secure or not...

MQARR-AODV: A NOVEL MULTIPATH QOS AWARE RELIABLE REVERSE ON-DEMAND DISTANCE VECTOR ROUTING PROTOCOL FOR MOBILE AD-HOC NETWORKS

Directory of Open Access Journals (Sweden)

K.G. Santhiya

2012-12-01

Full Text Available MANET (Mobile Ad-hoc Network is an infra structure less wireless ad-hoc network that does not require any basic central control. The topology of the network changes drastically due to very fast mobility of nodes. So an adaptive routing protocol is needed for routing in MANET. AODV (Ad-hoc On-demand Distance Vector routing is the effective and prominent on-demand Ad-hoc routing protocols. During route establishment phase in traditional AODV, only one route reply message will be sent in the reverse path to establish routing path. The high mobility of nodes may affect the reply messages which lead to the retransmission of route request message by the sender which in turn leads to higher communication delay, power consumption and the reduction in the ratio of packets delivered. Sending multiple route reply messages and establishing multiple paths in a single path discovery will reduce the routing overhead involved in maintaining the connection between source and destination nodes. Multipath routing can render high scalability, end-to-end throughput and provide load balancing in MANET. The new proposed novel Multipath QoS aware reliable routing protocol establishes two routes of maximum node disjoint paths and the data transfer is carried out in the two paths simultaneously. To select best paths, the new proposed protocol uses three parameters Link Eminence, MAC overhead and node residual energy. The experimental values prove that the MQARR-AODV protocol achieves high reliability, stability, low latency and outperforms AODV by the less energy consumption, overhead and delay.

UAV telemetry communications using ZigBee protocol

Science.gov (United States)

Nasution, T. H.; Siregar, I.; Yasir, M.

2017-10-01

Wireless communication has been widely used in various fields or disciplines such as agriculture, health, engineering, military, and aerospace so as to support the work in that field. The communication technology is typically used for controlling devices and data monitoring. One development of wireless communication is the widely used telemetry system used to reach areas that cannot be reached by humans using UAV (Unmanned Aerial Vehicle) or unmanned aircraft. In this paper we discuss the design of telemetry system in UAV using ZigBee protocol. From the test obtained the system can work well with visualization displays without pause is 20 data per second with a maximum data length of 120 characters.

Fault recovery in the reliable multicast protocol

Science.gov (United States)

Callahan, John R.; Montgomery, Todd L.; Whetten, Brian

1995-01-01

The Reliable Multicast Protocol (RMP) provides a unique, group-based model for distributed programs that need to handle reconfiguration events at the application layer. This model, called membership views, provides an abstraction in which events such as site failures, network partitions, and normal join-leave events are viewed as group reformations. RMP provides access to this model through an application programming interface (API) that notifies an application when a group is reformed as the result of a some event. RMP provides applications with reliable delivery of messages using an underlying IP Multicast (12, 5) media to other group members in a distributed environment even in the case of reformations. A distributed application can use various Quality of Service (QoS) levels provided by RMP to tolerate group reformations. This paper explores the implementation details of the mechanisms in RMP that provide distributed applications with membership view information and fault recovery capabilities.

Streetlight Control System Based on Wireless Communication over DALI Protocol

Science.gov (United States)

Bellido-Outeiriño, Francisco José; Quiles-Latorre, Francisco Javier; Moreno-Moreno, Carlos Diego; Flores-Arias, José María; Moreno-García, Isabel; Ortiz-López, Manuel

2016-01-01

Public lighting represents a large part of the energy consumption of towns and cities. Efficient management of public lighting can entail significant energy savings. This work presents a smart system for managing public lighting networks based on wireless communication and the DALI protocol. Wireless communication entails significant economic savings, as there is no need to install new wiring and visual impacts and damage to the facades of historical buildings in city centers are avoided. The DALI protocol uses bidirectional communication with the ballast, which allows its status to be controlled and monitored at all times. The novelty of this work is that it tackles all aspects related to the management of public lighting: a standard protocol, DALI, was selected to control the ballast, a wireless node based on the IEEE 802.15.4 standard with a DALI interface was designed, a network layer that considers the topology of the lighting network has been developed, and lastly, some user-friendly applications for the control and maintenance of the system by the technical crews of the different towns and cities have been developed. PMID:27128923

Streetlight Control System Based on Wireless Communication over DALI Protocol.

Science.gov (United States)

Bellido-Outeiriño, Francisco José; Quiles-Latorre, Francisco Javier; Moreno-Moreno, Carlos Diego; Flores-Arias, José María; Moreno-García, Isabel; Ortiz-López, Manuel

2016-04-27

Public lighting represents a large part of the energy consumption of towns and cities. Efficient management of public lighting can entail significant energy savings. This work presents a smart system for managing public lighting networks based on wireless communication and the DALI protocol. Wireless communication entails significant economic savings, as there is no need to install new wiring and visual impacts and damage to the facades of historical buildings in city centers are avoided. The DALI protocol uses bidirectional communication with the ballast, which allows its status to be controlled and monitored at all times. The novelty of this work is that it tackles all aspects related to the management of public lighting: a standard protocol, DALI, was selected to control the ballast, a wireless node based on the IEEE 802.15.4 standard with a DALI interface was designed, a network layer that considers the topology of the lighting network has been developed, and lastly, some user-friendly applications for the control and maintenance of the system by the technical crews of the different towns and cities have been developed.

Reliable Communication in Wireless Meshed Networks using Network Coding

DEFF Research Database (Denmark)

Pahlevani, Peyman; Paramanathan, Achuthan; Hundebøll, Martin

2012-01-01

The advantages of network coding have been extensively studied in the field of wireless networks. Integrating network coding with existing IEEE 802.11 MAC layer is a challenging problem. The IEEE 802.11 MAC does not provide any reliability mechanisms for overheard packets. This paper addresses...... this problem and suggests different mechanisms to support reliability as part of the MAC protocol. Analytical expressions to this problem are given to qualify the performance of the modified network coding. These expressions are confirmed by numerical result. While the suggested reliability mechanisms...

MDP: Reliable File Transfer for Space Missions

Science.gov (United States)

Rash, James; Criscuolo, Ed; Hogie, Keith; Parise, Ron; Hennessy, Joseph F. (Technical Monitor)

2002-01-01

This paper presents work being done at NASA/GSFC by the Operating Missions as Nodes on the Internet (OMNI) project to demonstrate the application of the Multicast Dissemination Protocol (MDP) to space missions to reliably transfer files. This work builds on previous work by the OMNI project to apply Internet communication technologies to space communication. The goal of this effort is to provide an inexpensive, reliable, standard, and interoperable mechanism for transferring files in the space communication environment. Limited bandwidth, noise, delay, intermittent connectivity, link asymmetry, and one-way links are all possible issues for space missions. Although these are link-layer issues, they can have a profound effect on the performance of transport and application level protocols. MDP, a UDP-based reliable file transfer protocol, was designed for multicast environments which have to address these same issues, and it has done so successfully. Developed by the Naval Research Lab in the mid 1990's, MDP is now in daily use by both the US Post Office and the DoD. This paper describes the use of MDP to provide automated end-to-end data flow for space missions. It examines the results of a parametric study of MDP in a simulated space link environment and discusses the results in terms of their implications for space missions. Lessons learned are addressed, which suggest minor enhancements to the MDP user interface to add specific features for space mission requirements, such as dynamic control of data rate, and a checkpoint/resume capability. These are features that are provided for in the protocol, but are not implemented in the sample MDP application that was provided. A brief look is also taken at the status of standardization. A version of MDP known as NORM (Neck Oriented Reliable Multicast) is in the process of becoming an IETF standard.

Toddlers favor communicatively presented information over statistical reliability in learning about artifacts.

Directory of Open Access Journals (Sweden)

Hanna Marno

Full Text Available Observed associations between events can be validated by statistical information of reliability or by testament of communicative sources. We tested whether toddlers learn from their own observation of efficiency, assessed by statistical information on reliability of interventions, or from communicatively presented demonstration, when these two potential types of evidence of validity of interventions on a novel artifact are contrasted with each other. Eighteen-month-old infants observed two adults, one operating the artifact by a method that was more efficient (2/3 probability of success than that of the other (1/3 probability of success. Compared to the Baseline condition, in which communicative signals were not employed, infants tended to choose the less reliable method to operate the artifact when this method was demonstrated in a communicative manner in the Experimental condition. This finding demonstrates that, in certain circumstances, communicative sanctioning of reliability may override statistical evidence for young learners. Such a bias can serve fast and efficient transmission of knowledge between generations.

Efficient SCT Protocol for Post Disaster Communication

Science.gov (United States)

Ramesh, T. K.; Giriraja, C. V.

2017-08-01

Natural and catastrophic disasters can cause damage to the communication system, the damage may be complete or it may be partial. In such areas communication and exchange of information plays a very important role and become difficult to happen in such situations. So, the rescue systems should be installed in those areas for the rescue operations and to take important decisions about how to make a connection from there to the outside world. Wireless communication network architecture should be setup in disaster areas for the communication to happen and to gather information. Wireless ad-hoc network architecture is proposed in this paper with access nodes. These access nodes acts as hotspot for certain area in which they are set up such that the Wi-Fi capable devices get connected to them for communication to happen. If the mobile battery is drained in such situations wireless charging using microwave is shown in this paper. Performance analysis of the communication transport layer protocols is shown and Efficient SCTP (ESTP) algorithm is developed which shows better results in terms of cumulative packet loss.

From Explicit to Symbolic Types for Communication Protocols in CCS

DEFF Research Database (Denmark)

Nielson, Hanne Riis; Nielson, Flemming; Kreiker, Jörg

2012-01-01

We study communication protocols having several rounds and expressed in value passing CCS. We develop a type-based analysis for providing an explicit record of all communications and show the usual subject reduction result. Since the explicit records can be infinitely large, we also develop a type...

On the reliability evaluation of communication equipment for SMART using FMEA

International Nuclear Information System (INIS)

Kim, D. H.; Suh, Y. S.; Koo, I. S.; Song, Ki Sang; Han, Byung Rae

2000-07-01

This report describes the reliability analysis method for communication equipment using FMEA and FTA. The major equipments to be applicable for SMART communication networks are repeater, bridge, router and gateway and we can apply the FMEA or FTA technique. In the FMEA process, analysis of tagged system, decision of the level of analysis of the target system, drawing reliability block diagram according to the function, decision of failure mode, writing the fault reasons, writing on the FMEA sheet and FMEA level decision are included. Also, the FTA, it is possible to figure out top event reasons and system reliability. We have considered these in mind and we did the FMEA and FTA for NIC, hub, client server and router. Also, we suggested and integrated network model for nuclear power plant and we have shown the reliability analysis procedure according to FTA. If any proprietary communication device is developed, the reliability can be easily determined with proposed procedures

On the reliability evaluation of communication equipment for SMART using FMEA

Energy Technology Data Exchange (ETDEWEB)

Kim, D. H.; Suh, Y. S.; Koo, I. S.; Song, Ki Sang; Han, Byung Rae

2000-07-01

This report describes the reliability analysis method for communication equipment using FMEA and FTA. The major equipments to be applicable for SMART communication networks are repeater, bridge, router and gateway and we can apply the FMEA or FTA technique. In the FMEA process, analysis of tagged system, decision of the level of analysis of the target system, drawing reliability block diagram according to the function, decision of failure mode, writing the fault reasons, writing on the FMEA sheet and FMEA level decision are included. Also, the FTA, it is possible to figure out top event reasons and system reliability. We have considered these in mind and we did the FMEA and FTA for NIC, hub, client server and router. Also, we suggested and integrated network model for nuclear power plant and we have shown the reliability analysis procedure according to FTA. If any proprietary communication device is developed, the reliability can be easily determined with proposed procedures.

IoT real time data acquisition using MQTT protocol

Science.gov (United States)

Atmoko, R. A.; Riantini, R.; Hasin, M. K.

2017-05-01

The Internet of Things (IoT) provides ease to monitor and to gain sensor data through the Internet [1]. The need of high quality data is increasing to the extent that data monitoring and acquisition system in real time is required, such as smart city or telediagnostic in medical areas [2]. Therefore, an appropriate communication protocol is required to resolve these problems. Lately, researchers have developed a lot of communication protocols for IoT, of which each has advantages and disadvantages. This study proposes the utilization of MQTT as a communication protocol, which is one of data communication protocols for IoT. This study used temperature and humidity sensors because the physical parameters are often needed as parameters of environment condition [3]. Data acquisition was done in real-time and stored in MySQL database. This study is also completed by interface web-based and mobile for online monitoring. This result of this study is the enhancement of data quality and reliability using MQTT protocol.

Reliability Improved Cooperative Communication over Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Zhuangbin Chen

2017-10-01

Full Text Available With the development of smart devices and connection technologies, Wireless Sensor Networks (WSNs are becoming increasingly intelligent. New or special functions can be obtained by receiving new versions of program codes to upgrade their software systems, forming the so-called smart Internet of Things (IoT. Due to the lossy property of wireless channels, data collection in WSNs still suffers from a long delay, high energy consumption, and many retransmissions. Thanks to wireless software-defined networks (WSDNs, software in sensors can now be updated to help them transmit data cooperatively, thereby achieving more reliable communication. In this paper, a Reliability Improved Cooperative Communication (RICC data collection scheme is proposed to improve the reliability of random-network-coding-based cooperative communications in multi-hop relay WSNs without reducing the network lifetime. In WSNs, sensors in different positions can have different numbers of packets to handle, resulting in the unbalanced energy consumption of the network. In particular, nodes in non-hotspot areas have up to 90% of their original energy remaining when the network dies. To efficiently use the residual energy, in RICC, high data transmission power is adopted in non-hotspot areas to achieve a higher reliability at the cost of large energy consumption, and relatively low transmission power is adopted in hotspot areas to maintain the long network lifetime. Therefore, high reliability and a long network lifetime can be obtained simultaneously. The simulation results show that compared with other scheme, RICC can reduce the end-to-end Message Fail delivering Ratio (MFR by 59.4%–62.8% under the same lifetime with a more balanced energy utilization.

SDL-Based Protocol Validation for the Integrated Safety Communication Network in Nuclear Power Plants

International Nuclear Information System (INIS)

Kim, Jung-hun; Kim, Dong-hoon; Lee, Dong-young; Park, Sung-woo

2006-01-01

The communication protocol in nuclear power plants needs to be validated systematically to avoid the critical situation that may be caused by its own faults. We establish the methodology to validate the protocol designed for the Integrated Safety Communication Networks (ISCN) of Korea Nuclear Instrumentation and Control System (KNICS). The ISCN protocol is specified using the formal description technique called the SDL. The validation of ISCN protocol is done via the Simulator and Validator, both of which are main functions provided by the SDL

Communicating systems with UML 2 modeling and analysis of network protocols

CERN Document Server

Barrera, David Garduno

2013-01-01

This book gives a practical approach to modeling and analyzing communication protocols using UML 2. Network protocols are always presented with a point of view focusing on partial mechanisms and starting models. This book aims at giving the basis needed for anybody to model and validate their own protocols. It follows a practical approach and gives many examples for the description and analysis of well known basic network mechanisms for protocols.The book firstly shows how to describe and validate the main protocol issues (such as synchronization problems, client-server interactions, layer

Streetlight Control System Based on Wireless Communication over DALI Protocol

Directory of Open Access Journals (Sweden)

Francisco José Bellido-Outeiriño

2016-04-01

Full Text Available Public lighting represents a large part of the energy consumption of towns and cities. Efficient management of public lighting can entail significant energy savings. This work presents a smart system for managing public lighting networks based on wireless communication and the DALI protocol. Wireless communication entails significant economic savings, as there is no need to install new wiring and visual impacts and damage to the facades of historical buildings in city centers are avoided. The DALI protocol uses bidirectional communication with the ballast, which allows its status to be controlled and monitored at all times. The novelty of this work is that it tackles all aspects related to the management of public lighting: a standard protocol, DALI, was selected to control the ballast, a wireless node based on the IEEE 802.15.4 standard with a DALI interface was designed, a network layer that considers the topology of the lighting network has been developed, and lastly, some user-friendly applications for the control and maintenance of the system by the technical crews of the different towns and cities have been developed.

Verification of the safety communication protocol in train control system using colored Petri net

International Nuclear Information System (INIS)

Chen Lijie; Tang Tao; Zhao Xianqiong; Schnieder, Eckehard

2012-01-01

This paper deals with formal and simulation-based verification of the safety communication protocol in ETCS (European Train Control System). The safety communication protocol controls the establishment of safety connection between train and trackside. Because of its graphical user interface and modeling flexibility upon the changes in the system conditions, this paper proposes a composition Colored Petri Net (CPN) representation for both the logic and the timed model. The logic of the protocol is proved to be safe by means of state space analysis: the dead markings are correct; there are no dead transitions; being fair. Further analysis results have been obtained using formal and simulation-based verification approach. The timed models for the open transmit system and the application process are created for the purpose of performance analysis of the safety communication protocol. The models describe the procedure of data transmission and processing, and also provide relevant timed and stochastic factors, as well as time delay and lost packet, which may influence the time for establishment of safety connection of the protocol. Time for establishment of safety connection of the protocol in normal state is verified by formal verification, and then time for establishment of safety connection with different probability of lost packet is simulated. After verification it is found that the time for establishment of safety connection of the safety communication protocol satisfies the safety requirements.

End-to-end Configuration of Wireless Realtime Communication over Heterogeneous Protocols

DEFF Research Database (Denmark)

Malinowsky, B.; Grønbæk, Jesper; Schwefel, Hans-Peter

2015-01-01

This paper describes a wireless real-time communication system design using two Time Division Multiple Access (TDMA) protocols. Messages are subject to prioritization and queuing. For this interoperation scenario, we show a method for end-to-end configuration of protocols and queue sizes. Such co...

Task Group on Computer/Communication Protocols for Bibliographic Data Exchange. Interim Report = Groupe de Travail sur les Protocoles de Communication/Ordinateurs pour l'Exchange de Donnees Bibliographiques. Rapport d'Etape. May 1983.

Science.gov (United States)

Canadian Network Papers, 1983

1983-01-01

This preliminary report describes the work to date of the Task Group on Computer/Communication protocols for Bibliographic Data Interchange, which was formed in 1980 to develop a set of protocol standards to facilitate communication between heterogeneous library and information systems within the framework of Open Systems Interconnection (OSI). A…

Application of Modbus communication protocol and float-point display in MCS51 system

International Nuclear Information System (INIS)

Kong Xiangcheng; Liu Shaozhen

2010-01-01

As its widely opening and easy performance, Modbus communication protocol has a great advantage in field bus using. Details are given on a method to implement Modbus communication protocol based on MCS51 system, and the advantage of uVision integrated environment. The design realizes Modbus RTU mode communication, meanwhile the problem of synchronization in communication is solved. And float-point operation and display are achieved by format print. All of this are carried out under uVision integrated environment. The result approves that the response ratio of Modbus communication is 100%. The design shows the advantage of uVision integrated environment and MCS51 system. And also gives solution to the occasion where communication interface and low cost are required. (authors)

Security analysis of standards-driven communication protocols for healthcare scenarios.

Science.gov (United States)

Masi, Massimiliano; Pugliese, Rosario; Tiezzi, Francesco

2012-12-01

The importance of the Electronic Health Record (EHR), that stores all healthcare-related data belonging to a patient, has been recognised in recent years by governments, institutions and industry. Initiatives like the Integrating the Healthcare Enterprise (IHE) have been developed for the definition of standard methodologies for secure and interoperable EHR exchanges among clinics and hospitals. Using the requisites specified by these initiatives, many large scale projects have been set up for enabling healthcare professionals to handle patients' EHRs. The success of applications developed in these contexts crucially depends on ensuring such security properties as confidentiality, authentication, and authorization. In this paper, we first propose a communication protocol, based on the IHE specifications, for authenticating healthcare professionals and assuring patients' safety. By means of a formal analysis carried out by using the specification language COWS and the model checker CMC, we reveal a security flaw in the protocol thus demonstrating that to simply adopt the international standards does not guarantee the absence of such type of flaws. We then propose how to emend the IHE specifications and modify the protocol accordingly. Finally, we show how to tailor our protocol for application to more critical scenarios with no assumptions on the communication channels. To demonstrate feasibility and effectiveness of our protocols we have fully implemented them.

Numerical simulation of the effect of dissipation and phase fluctuation in a direct communication scheme

International Nuclear Information System (INIS)

Li, Fu; Zhu, Shi-Yao; Zhang, Jun-Xiang

2015-01-01

Recently, the direct counterfactual communication protocol, proposed by Salih et al (2013 Phys. Rev. Lett. 110 170502) using a single photon source under ideal conditions (no dissipation, no phase fluctuation and an infinite number of beam splitters), has attracted much interest from a broad range of scientists. In order to put the direct communication protocol into a realistic framework, we numerically simulate the effect of the dissipation and the phase fluctuation with a finite number of beam splitters. Our calculation shows that the dissipation and phase fluctuation will dramatically decrease the reliability and the efficiency of communication, and even corrupt the communication. To counteract the negative effect of dissipation, we propose the balanced dissipation method, which substantially improves the reliability of the protocol at the expense of decreasing communication efficiency. Meanwhile, our theoretical derivation shows that the reliability and efficiency of communication are independent of the input state: a single photon state or a coherent state. (paper)

Numerical simulation of the effect of dissipation and phase fluctuation in a direct communication scheme

Science.gov (United States)

Li, Fu; Zhang, Jun-Xiang; Zhu, Shi-Yao

2015-06-01

Recently, the direct counterfactual communication protocol, proposed by Salih et al (2013 Phys. Rev. Lett. 110 170502) using a single photon source under ideal conditions (no dissipation, no phase fluctuation and an infinite number of beam splitters), has attracted much interest from a broad range of scientists. In order to put the direct communication protocol into a realistic framework, we numerically simulate the effect of the dissipation and the phase fluctuation with a finite number of beam splitters. Our calculation shows that the dissipation and phase fluctuation will dramatically decrease the reliability and the efficiency of communication, and even corrupt the communication. To counteract the negative effect of dissipation, we propose the balanced dissipation method, which substantially improves the reliability of the protocol at the expense of decreasing communication efficiency. Meanwhile, our theoretical derivation shows that the reliability and efficiency of communication are independent of the input state: a single photon state or a coherent state.

Timing Analysis of Rate Constrained Traffic for the TTEthernet Communication Protocol

DEFF Research Database (Denmark)

Tamas-Selicean, Domitian; Pop, Paul; Steiner, Wilfried

2015-01-01

Ethernet is a low-cost communication solution offering high transmission speeds. Although its applications extend beyond computer networking, Ethernet is not suitable for real-time and safety-critical systems. To alleviate this, several real-time Ethernet-based communication protocols have been...

Software coding for reliable data communication in a reactor safety system

International Nuclear Information System (INIS)

Maghsoodi, R.

1978-01-01

A software coding method is proposed to improve the communication reliability of a microprocessor based fast-reactor safety system. This method which replaces the conventional coding circuitry, applies a program to code the data which is communicated between the processors via their data memories. The system requirements are studied and the suitable codes are suggested. The problems associated with hardware coders, and the advantages of software coding methods are discussed. The product code which proves a faster coding time over the cyclic code is chosen as the final code. Then the improvement of the communication reliability is derived for a processor and its data memory. The result is used to calculate the reliability improvement of the processing channel as the basic unit for the safety system. (author)

Wireless communications networks for the smart grid

CERN Document Server

Ho, Quang-Dung; Rajalingham, Gowdemy; Le-Ngoc, Tho

2014-01-01

This brief presents a comprehensive review of the network architecture and communication technologies of the smart grid communication network (SGCN). It then studies the strengths, weaknesses and applications of two promising wireless mesh routing protocols that could be used to implement the SGCN. Packet transmission reliability, latency and robustness of these two protocols are evaluated and compared by simulations in various practical SGCN scenarios. Finally, technical challenges and open research opportunities of the SGCN are addressed. Wireless Communications Networks for Smart Grid provi

Reliable vehicular broadcast using 5G device-to-device communication

NARCIS (Netherlands)

Gholibeigi, Mozhdeh; Sarrionandia, Nora; Karimzadeh Motallebi Azar, Morteza; Baratchi, Mitra; van den Berg, Hans Leo; Heijenk, Geert

2017-01-01

With the ever-increasing call for connected vehicles and intelligent transportation applications, vehicular networking have been of significant focus recently. Demands for highly reliable communication challenge the current underlying technology and transformations in vehicular communication are

Reliable quantum communication over a quantum relay channel

Energy Technology Data Exchange (ETDEWEB)

Gyongyosi, Laszlo, E-mail: gyongyosi@hit.bme.hu [Quantum Technologies Laboratory, Department of Telecommunications, Budapest University of Technology and Economics, 2 Magyar tudosok krt, Budapest, H-1117, Hungary and Information Systems Research Group, Mathematics and Natural Sciences, Hungarian Ac (Hungary); Imre, Sandor [Quantum Technologies Laboratory, Department of Telecommunications, Budapest University of Technology and Economics, 2 Magyar tudosok krt, Budapest, H-1117 (Hungary)

2014-12-04

We show that reliable quantum communication over an unreliable quantum relay channels is possible. The coding scheme combines the results on the superadditivity of quantum channels and the efficient quantum coding approaches.

Reliability and criterion validity of an observation protocol for working technique assessments in cash register work.

Science.gov (United States)

Palm, Peter; Josephson, Malin; Mathiassen, Svend Erik; Kjellberg, Katarina

2016-06-01

We evaluated the intra- and inter-observer reliability and criterion validity of an observation protocol, developed in an iterative process involving practicing ergonomists, for assessment of working technique during cash register work for the purpose of preventing upper extremity symptoms. Two ergonomists independently assessed 17 15-min videos of cash register work on two occasions each, as a basis for examining reliability. Criterion validity was assessed by comparing these assessments with meticulous video-based analyses by researchers. Intra-observer reliability was acceptable (i.e. proportional agreement >0.7 and kappa >0.4) for 10/10 questions. Inter-observer reliability was acceptable for only 3/10 questions. An acceptable inter-observer reliability combined with an acceptable criterion validity was obtained only for one working technique aspect, 'Quality of movements'. Thus, major elements of the cashiers' working technique could not be assessed with an acceptable accuracy from short periods of observations by one observer, such as often desired by practitioners. Practitioner Summary: We examined an observation protocol for assessing working technique in cash register work. It was feasible in use, but inter-observer reliability and criterion validity were generally not acceptable when working technique aspects were assessed from short periods of work. We recommend the protocol to be used for educational purposes only.

Coexistence of enhanced mobile broadband communications and ultra-reliable low-latency communications in mobile front-haul

Science.gov (United States)

Ying, Kai; Kowalski, John M.; Nogami, Toshizo; Yin, Zhanping; Sheng, Jia

2018-01-01

5G systems are supposed to support coexistence of multiple services such as ultra reliable low latency communications (URLLC) and enhanced mobile broadband (eMBB) communications. The target of eMBB communications is to meet the high-throughput requirement while URLLC are used for some high priority services. Due to the sporadic nature and low latency requirement, URLLC transmission may pre-empt the resource of eMBB transmission. Our work is to analyze the URLLC impact on eMBB transmission in mobile front-haul. Then, some solutions are proposed to guarantee the reliability/latency requirements for URLLC services and minimize the impact to eMBB services at the same time.

Experimental investigation of quantum communication protocols in higher dimensions

International Nuclear Information System (INIS)

Groeblacher, S.; Stuetz, M.; Vaziri, A.; Jennewein, T.; Zeilinger, A.

2005-01-01

Full text: Higher dimensional quantum systems, such as qutrits, offer unique possibilities for quantum communication. In particular, quantum key distribution may be realized with a higher security margin than with qubit systems. We plan to demonstrate quantum cryptography with entangled photonic qutrits based on orbital angular momentum (OAM). Therefore we test various methods of manipulating and transforming OAM states of photons, which is required for the implementation of quantum communication protocols. (author)

Latency Analysis of Systems with Multiple Interfaces for Ultra-Reliable M2M Communication

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Popovski, Petar

2016-01-01

One of the ways to satisfy the requirements of ultra-reliable low latency communication for mission critical Machine-type Communications (MTC) applications is to integrate multiple communication interfaces. In order to estimate the performance in terms of latency and reliability of such an integr...

A Smart Collaborative Routing Protocol for Reliable Data Diffusion in IoT Scenarios.

Science.gov (United States)

Ai, Zheng-Yang; Zhou, Yu-Tong; Song, Fei

2018-06-13

It is knotty for current routing protocols to meet the needs of reliable data diffusion during the Internet of Things (IoT) deployments. Due to the random placement, limited resources and unattended features of existing sensor nodes, the wireless transmissions are easily exposed to unauthorized users, which becomes a vulnerable area for various malicious attacks, such as wormhole and Sybil attacks. However, the scheme based on geographic location is a suitable candidate to defend against them. This paper is inspired to propose a smart collaborative routing protocol, Geographic energy aware routing and Inspecting Node (GIN), for guaranteeing the reliability of data exchanging. The proposed protocol integrates the directed diffusion routing, Greedy Perimeter Stateless Routing (GPSR), and the inspecting node mechanism. We first discuss current wireless routing protocols from three diverse perspectives (improving transmission rate, shortening transmission range and reducing transmission consumption). Then, the details of GIN, including the model establishment and implementation processes, are presented by means of the theoretical analysis. Through leveraging the game theory, the inspecting node is elected to monitor the network behaviors. Thirdly, we evaluate the network performances, in terms of transmission delay, packet loss ratio, and throughput, between GIN and three traditional schemes (i.e., Flooding, GPSR, and GEAR). The simulation results illustrate that the proposed protocol is able to outperform the others.

A Generic, Modular and User Transparent Protocol Scheme for Inter-FPGA Communication using Serial Links

CERN Document Server

AUTHOR|(CDS)2209162; Emery, Jonathan

CERN, the European Organization for Nuclear Research, is a European research organization that operates the largest particle physics laboratory in the world. A large amount of particle accelerators and detectors are developed and used for scientific research purposes. With those, a large amount of information is created and needs to be stored before it can be analysed. As a consequence, the communication reliability, integrity, latency and transfer rates between these detectors and the control room are some of the key elements for the success of those experiments. While it is true that existing communication standards, or protocols, are focused on those key elements, it is usually a balanced compromise to stay polyvalent, where the emphasis on a specific aspect reduces the efficiency of the others. To improve the performance and capabilities of one of the operational accelerator instrument called the beam wire scanner (BWS), the CERN instrumentation Group (BE-BI) has created a complete new electro-mech...

Interfaces and Communication Protocols in ATCA-Based LLRF Control Systems

Science.gov (United States)

Makowski, Dariusz; Koprek, Waldemar; Jezynski, Tomasz; Piotrowski, Adam; Jablonski, Grzegorz; Jalmuzna, Wojciech; Simrock, Stefan

2009-10-01

Linear accelerators driving Free Electron Lasers (FELs), such as the Free Electron Laser in Hamburg (FLASH) or the X-ray Free Electron Laser (XFEL), require sophisticated Low Level Radio Frequency (LLRF) control systems. The controller of the LLRF system should stabilize the phase and amplitude of the field in accelerating modules below 0.02% of the amplitude and 0.01 degree for phase tolerances to produce an ultra stable electron beam that meets the required conditions for Self-Amplified Spontaneous Emission (SASE). Since the LLRF system for the XFEL must be in operation for the next 20 years, it should be reliable, reproducible and upgradeable. Having in mind all requirements of the LLRF control system, the Advanced Telecommunications Computing Architecture (ATCA) has been chosen to build a prototype of the LLRF system for the FLASH accelerator that is able to supervise 32 cavities of one RF station. The LLRF controller takes advantage of features offered by the ATCA standard. The LLRF system consists of a few ATCA carrier blades, Rear Transition Modules (RTM) and several Advanced Mezzanine Cards (AMCs) that provide all necessary digital and analog hardware components. The distributed hardware of the LLRF system requires a number of communication links that should provide different latencies, bandwidths and protocols. The paper presents the general view of the ATC A-based LLRF system, discusses requirements and proposes an application for various interfaces and protocols in the distributed LLRF control system.

Characterization of perovskite solar cells: Towards a reliable measurement protocol

Directory of Open Access Journals (Sweden)

Eugen Zimmermann

2016-09-01

Full Text Available Lead halide perovskite solar cells have shown a tremendous rise in power conversion efficiency with reported record efficiencies of over 20% making this material very promising as a low cost alternative to conventional inorganic solar cells. However, due to a differently severe “hysteretic” behaviour during current density-voltage measurements, which strongly depends on scan rate, device and measurement history, preparation method, device architecture, etc., commonly used solar cell measurements do not give reliable or even reproducible results. For the aspect of commercialization and the possibility to compare results of different devices among different laboratories, it is necessary to establish a measurement protocol which gives reproducible results. Therefore, we compare device characteristics derived from standard current density-voltage measurements with stabilized values obtained from an adaptive tracking of the maximum power point and the open circuit voltage as well as characteristics extracted from time resolved current density-voltage measurements. Our results provide insight into the challenges of a correct determination of device performance and propose a measurement protocol for a reliable characterisation which is easy to implement and has been tested on varying perovskite solar cells fabricated in different laboratories.

Test-retest reliability of jump execution variables using mechanography: a comparison of jump protocols.

Science.gov (United States)

Fitzgerald, John S; Johnson, LuAnn; Tomkinson, Grant; Stein, Jesse; Roemmich, James N

2018-05-01

Mechanography during the vertical jump may enhance screening and determining mechanistic causes underlying physical performance changes. Utility of jump mechanography for evaluation is limited by scant test-retest reliability data on force-time variables. This study examined the test-retest reliability of eight jump execution variables assessed from mechanography. Thirty-two women (mean±SD: age 20.8 ± 1.3 yr) and 16 men (age 22.1 ± 1.9 yr) attended a familiarization session and two testing sessions, all one week apart. Participants performed two variations of the squat jump with squat depth self-selected and controlled using a goniometer to 80º knee flexion. Test-retest reliability was quantified as the systematic error (using effect size between jumps), random error (using coefficients of variation), and test-retest correlations (using intra-class correlation coefficients). Overall, jump execution variables demonstrated acceptable reliability, evidenced by small systematic errors (mean±95%CI: 0.2 ± 0.07), moderate random errors (mean±95%CI: 17.8 ± 3.7%), and very strong test-retest correlations (range: 0.73-0.97). Differences in random errors between controlled and self-selected protocols were negligible (mean±95%CI: 1.3 ± 2.3%). Jump execution variables demonstrated acceptable reliability, with no meaningful differences between the controlled and self-selected jump protocols. To simplify testing, a self-selected jump protocol can be used to assess force-time variables with negligible impact on measurement error.

Communication protocol in chassis detecting wireless transmission system based on WiFi

Science.gov (United States)

In chassis detecting wireless transmission system, the wireless network communication protocol plays a key role in the information exchange and synchronization between the host and chassis PDA. This paper presents a wireless network transmission protocol based on TCP/IP which makes the rules of info...

Coordination Protocols for a Reliable Sensor, Actuator, and Device Network (SADN

Directory of Open Access Journals (Sweden)

Keiji Ozaki

2008-01-01

Full Text Available A sensor, actuator, and device network (SADN is composed of three types of nodes, which are sensor, actuator, and actuation device nodes. Sensor nodes and actuator nodes are interconnected in wireless networks as discussed in wireless sensor and actuator networks (WSANs. Actuator nodes and device nodes are interconnected in types of networks, i.e. wireless and wired network. Sensor nodes sense an physical event and send sensed values of the event to actuator nodes. An actuator node makes a decision on proper actions on receipt of sensed values and then issue the action requests to the device nodes. A device node really acts to the physical world. For example, moves a robot arms by performing the action on receipt of the action request. Messages may be lost and nodes may be faulty. Especially, messages are lost due to noise and collision in a wireless network. We propose a fully redundant model for an SADN where each of sensor, actuator, and device functions is replicated in multiple nodes and each of sensor-actuator and actuator-device communication is realized in many-to-many type of communication protocols. Even if some number of nodes are faulty, the other nodes can perform requested tasks. Here, each sensor node sends sensed values to multiple actuator nodes and each actuator node receives sensed values from multiple sensor nodes. While multiple actuator nodes communicate with multiple replica nodes of a device. Even if messages are lost and some number of nodes are faulty, device nodes can surely receive action requests required for sensed values and the actions are performed. In this paper, we discuss a type of semi-passive coordination (SPC protocol of multiple actuator nodes for multiple sensor nodes. We discuss a type of active coordination protocol for multiple actuator nodes and multiple actuation device nodes. We evaluate the SPC protocol for the sensor-actuator coordination in terms of the number of messages exchanged among

Reliability issues and solutions for coding social communication performance in classroom settings.

Science.gov (United States)

Olswang, Lesley B; Svensson, Liselotte; Coggins, Truman E; Beilinson, Jill S; Donaldson, Amy L

2006-10-01

To explore the utility of time-interval analysis for documenting the reliability of coding social communication performance of children in classroom settings. Of particular interest was finding a method for determining whether independent observers could reliably judge both occurrence and duration of ongoing behavioral dimensions for describing social communication performance. Four coders participated in this study. They observed and independently coded 6 social communication behavioral dimensions using handheld computers. The dimensions were mutually exclusive and accounted for all verbal and nonverbal productions during a specified time frame. The technology allowed for coding frequency and duration for each entered code. Data were collected from 20 different 2-min video segments of children in kindergarten through 3rd-grade classrooms. Data were analyzed for interobserver and intraobserver agreements using time-interval sorting and Cohen's kappa. Further, interval size and total observation length were manipulated to determine their influence on reliability. The data revealed interval sorting and kappa to be a suitable method for examining reliability of occurrence and duration of ongoing social communication behavioral dimensions. Nearly all comparisons yielded medium to large kappa values; interval size and length of observation minimally affected results. Implications The analysis procedure described in this research solves a challenge in reliability: comparing coding by independent observers of both occurrence and duration of behaviors. Results indicate the utility of a new coding taxonomy and technology for application in online observations of social communication in a classroom setting.

Signal Quality Outage Analysis for Ultra-Reliable Communications in Cellular Networks

DEFF Research Database (Denmark)

Gerardino, Guillermo Andrés Pocovi; Alvarez, Beatriz Soret; Lauridsen, Mads

2015-01-01

Ultra-reliable communications over wireless will open the possibility for a wide range of novel use cases and applications. In cellular networks, achieving reliable communication is challenging due to many factors, particularly the fading of the desired signal and the interference. In this regard......, we investigate the potential of several techniques to combat these main threats. The analysis shows that traditional microscopic multiple-input multiple-output schemes with 2x2 or 4x4 antenna configurations are not enough to fulfil stringent reliability requirements. It is revealed how such antenna...... schemes must be complemented with macroscopic diversity as well as interference management techniques in order to ensure the necessary SINR outage performance. Based on the obtained performance results, it is discussed which of the feasible options fulfilling the ultra-reliable criteria are most promising...

A reliable transmission protocol for ZigBee-based wireless patient monitoring.

Science.gov (United States)

Chen, Shyr-Kuen; Kao, Tsair; Chan, Chia-Tai; Huang, Chih-Ning; Chiang, Chih-Yen; Lai, Chin-Yu; Tung, Tse-Hua; Wang, Pi-Chung

2012-01-01

Patient monitoring systems are gaining their importance as the fast-growing global elderly population increases demands for caretaking. These systems use wireless technologies to transmit vital signs for medical evaluation. In a multihop ZigBee network, the existing systems usually use broadcast or multicast schemes to increase the reliability of signals transmission; however, both the schemes lead to significantly higher network traffic and end-to-end transmission delay. In this paper, we present a reliable transmission protocol based on anycast routing for wireless patient monitoring. Our scheme automatically selects the closest data receiver in an anycast group as a destination to reduce the transmission latency as well as the control overhead. The new protocol also shortens the latency of path recovery by initiating route recovery from the intermediate routers of the original path. On the basis of a reliable transmission scheme, we implement a ZigBee device for fall monitoring, which integrates fall detection, indoor positioning, and ECG monitoring. When the triaxial accelerometer of the device detects a fall, the current position of the patient is transmitted to an emergency center through a ZigBee network. In order to clarify the situation of the fallen patient, 4-s ECG signals are also transmitted. Our transmission scheme ensures the successful transmission of these critical messages. The experimental results show that our scheme is fast and reliable. We also demonstrate that our devices can seamlessly integrate with the next generation technology of wireless wide area network, worldwide interoperability for microwave access, to achieve real-time patient monitoring.

Emergency Handling for MAC Protocol in Human Body Communication

Directory of Open Access Journals (Sweden)

Kwon Youngmi

2011-01-01

Full Text Available The human body communication (HBC is a technology that enables short range data communication using the human body as a medium, like an electrical wire. Thus it removes the need for a traditional antenna. HBC may be used as a type of data communication in body area network (BAN, while the devices are being in contact with body. One of important issues in BAN is an emergency alarm because it may be closely related to human life. For emergency data communication, the most critical factor is the time constraint. IEEE 802.15.6 specifies that the emergency alarm for the BAN must be notified in less than 1 sec and must provide prioritization mechanisms for emergency traffic and notification. As one type of BAN, the HBC must follow this recommendation, too. Existing emergency handling methods in BAN are based on the carrier sensing capability on radio frequencies to detect the status of channels. However, PHY protocol in HBC does not provide the carrier sensing. So the previous methods are not well suitable for HBC directly. Additionally, in the environment that the emergency rate is very low, the allocation of dedicated slot(s for emergency in each superframe is very wasteful. In this work, we proposed specific emergency handling operation for human body communication's medium access control (HBC-MAC protocol to meet the emergency requirements for BAN. We also showed the optimal number of emergency slots for the various combinations of beacon intervals and emergency rates.

78 FR 10169 - Federal Advisory Committee Act; Communications Security, Reliability, and Interoperability Council

Science.gov (United States)

2013-02-13

... Location Accuracy, Network Security Best Practices, DNSSEC Implementation Practices for ISPs, Secure BGP... FEDERAL COMMUNICATIONS COMMISSION Federal Advisory Committee Act; Communications Security... persons that the Federal Communications Commission's (FCC) Communications Security, Reliability, and...

Promoting communication with older adults: protocols for resolving interpersonal conflicts and for enhancing interactions with doctors.

Science.gov (United States)

Weitzman, Patricia Flynn; Weitzman, Eben A

2003-07-01

In this paper, we review the importance of effective communication in older adulthood, and ideas for promoting it. We focus on theoretical and applied work in two communicative encounters that have particular relevance for older adult health, i.e., interpersonal conflict and visits with a healthcare provider. Little applied work has aimed to adapt training protocols for older adults in these two areas. We will present training protocols we have developed in constructive conflict resolution for older adults, and on enhancing doctor-patient communication. We present these protocols to stimulate ideas on the part of the reader on how to further develop and refine training efforts for older adults in effective communication.

76 FR 72922 - Federal Advisory Committee Act; Communications Security, Reliability, and Interoperability Council

Science.gov (United States)

2011-11-28

... alerting systems, 9-1-1 location accuracy, and network security. The FCC will attempt to accommodate as... FEDERAL COMMUNICATIONS COMMISSION Federal Advisory Committee Act; Communications Security... persons that the Federal Communications Commission's (FCC) third Communications Security, Reliability, and...

Protocols for Scholarly Communication

CERN Document Server

Pepe, Alberto; Pepe, Alberto; Yeomans, Joanne

2007-01-01

CERN, the European Organization for Nuclear Research, has operated an institutional preprint repository for more than 10 years. The repository contains over 850,000 records of which more than 450,000 are full-text OA preprints, mostly in the field of particle physics, and it is integrated with the library's holdings of books, conference proceedings, journals and other grey literature. In order to encourage effective propagation and open access to scholarly material, CERN is implementing a range of innovative library services into its document repository: automatic keywording, reference extraction, collaborative management tools and bibliometric tools. Some of these services, such as user reviewing and automatic metadata extraction, could make up an interesting testbed for future publishing solutions and certainly provide an exciting environment for e-science possibilities. The future protocol for scientific communication should naturally guide authors towards OA publication and CERN wants to help reach a full...

Beyond communication: the role of standardized protocols in a changing health care environment.

Science.gov (United States)

Vardaman, James M; Cornell, Paul; Gondo, Maria B; Amis, John M; Townsend-Gervis, Mary; Thetford, Carol

2012-01-01

Communication errors have grave consequences in health care settings. The situation-background-assessment-recommendation (SBAR) protocol has been theorized to improve communication by creating a common language between nurses and physicians in acute care situations. This practice is gaining acceptance across the health care field. However, as yet, there has been little investigation of the ways in which SBAR may have an impact on how health care professionals operate beyond the creation of a common language. The purposes of the study were to explore the implementation of the SBAR protocol and investigate the potential impact of SBAR on the day-to-day experiences of nurses. We performed a qualitative case study of 2 hospitals that were implementing the SBAR protocol. We collected data from 80 semistructured interviews with nurses, nurse manager, and physicians; observation of nursing and other hospital activities; and documents that pertained to the implementation of the SBAR protocol. Data were analyzed using a thematic approach. Our analysis revealed 4 dimensions of impact that SBAR has beyond its use as a communication tool: schema formation, development of legitimacy, development of social capital, and reinforcement of dominant logics. The results indicate that SBAR may function as more than a tool to standardize communication among nurses and physicians. Rather, the findings indicate that SBAR may aid in schema development that allows rapid decision making by nurses, provide social capital and legitimacy for less-tenured nurses, and reinforce a move toward standardization in the nursing profession. Our findings further suggest that standardized protocols such as SBAR may be a cost-effective method for hospital managers and administrators to accelerate the socialization of nurses, particularly new hires.

Design and analysis of communication protocols for quantum repeater networks

International Nuclear Information System (INIS)

Jones, Cody; Kim, Danny; Rakher, Matthew T; Ladd, Thaddeus D; Kwiat, Paul G

2016-01-01

We analyze how the performance of a quantum-repeater network depends on the protocol employed to distribute entanglement, and we find that the choice of repeater-to-repeater link protocol has a profound impact on entanglement-distribution rate as a function of hardware parameters. We develop numerical simulations of quantum networks using different protocols, where the repeater hardware is modeled in terms of key performance parameters, such as photon generation rate and collection efficiency. These parameters are motivated by recent experimental demonstrations in quantum dots, trapped ions, and nitrogen-vacancy centers in diamond. We find that a quantum-dot repeater with the newest protocol (‘MidpointSource’) delivers the highest entanglement-distribution rate for typical cases where there is low probability of establishing entanglement per transmission, and in some cases the rate is orders of magnitude higher than other schemes. Our simulation tools can be used to evaluate communication protocols as part of designing a large-scale quantum network. (paper)

Realization of Timed Reliable Communication over Off-The-Shelf Wireless Technologies

DEFF Research Database (Denmark)

Malinowsky, B.; Groenbaek, Jesper; Schwefel, Hans-Peter

2013-01-01

Industrial and safety-critical applications pose strict requirements for timeliness and reliability for the communication solution. Thereby the use of off-the-shelf (OTS) wireless communication technologies can be attractive to achieve low cost and easy deployment. This paper presents and analyse...

Design and Analysis of a secure multi-party communication protocol

OpenAIRE

Herberth, Klaus

2016-01-01

In the past years digital communication became an important aspect in every day life. Everything is shared and discussed in groups of friends, family or business part- ners without a proper way to protect that information. This master thesis introduces the first secure robust multi-party communication protocol which mimics a physical conversation with the help of a Diffie-Hellman key tree and social behaviours. Robust- ness against offline group members is reached by taking advantage of trans...

A wireless mesh communication protocol for smart-metering

NARCIS (Netherlands)

Geelen, D.J.M.; Kempen, van G.M.P.; Hoogstraten, van F.; Liotta, A.

2012-01-01

Worldwide there has been increasing interest over the past few years for so-called "Smart Meters", in academia, governments and in industry. Such smart-metering systems need a way to communicate the collected data reliably and cost efficiently to the back-office for analysis. Several competing

Protocols for Scholarly Communication

Science.gov (United States)

Pepe, A.; Yeomans, J.

2007-10-01

CERN, the European Organization for Nuclear Research, has operated an institutional preprint repository for more than 10 years. The repository contains over 850,000 records of which more than 450,000 are full-text OA preprints, mostly in the field of particle physics, and it is integrated with the library's holdings of books, conference proceedings, journals and other grey literature. In order to encourage effective propagation and open access to scholarly material, CERN is implementing a range of innovative library services into its document repository: automatic keywording, reference extraction, collaborative management tools and bibliometric tools. Some of these services, such as user reviewing and automatic metadata extraction, could make up an interesting testbed for future publishing solutions and certainly provide an exciting environment for e-science possibilities. The future protocol for scientific communication should guide authors naturally towards OA publication, and CERN wants to help reach a full open access publishing environment for the particle physics community and related sciences in the next few years.

Secure Handshake in Wi-Fi Connection (A Secure and Enhanced Communication Protocol)

OpenAIRE

Ranbir Sinha; Nishant Behar; Devendra Singh

2012-01-01

This paper presents a concept of enhancing the security in wireless communication. A Computer Network is an interconnected group of autonomous computing nodes, which use a well-defined, mutually agreed set of rules and conventions known as protocols, interact with one-another meaningfully and allow resource sharing preferably in a predictable and controllable manner. Communication has a major impact on today’s business. It is desired to communicate data with high security. These days wireless...

Reliability modeling of safety-critical network communication in a digitalized nuclear power plant

International Nuclear Information System (INIS)

Lee, Sang Hun; Kim, Hee Eun; Son, Kwang Seop; Shin, Sung Min; Lee, Seung Jun; Kang, Hyun Gook

2015-01-01

The Engineered Safety Feature-Component Control System (ESF-CCS), which uses a network communication system for the transmission of safety-critical information from group controllers (GCs) to loop controllers (LCs), was recently developed. However, the ESF-CCS has not been applied to nuclear power plants (NPPs) because the network communication failure risk in the ESF-CCS has yet to be fully quantified. Therefore, this study was performed to identify the potential hazardous states for network communication between GCs and LCs and to develop quantification schemes for various network failure causes. To estimate the risk effects of network communication failures in the ESF-CCS, a fault-tree model of an ESF-CCS signal failure in the containment spray actuation signal condition was developed for the case study. Based on a specified range of periodic inspection periods for network modules and the baseline probability of software failure, a sensitivity study was conducted to analyze the risk effect of network failure between GCs and LCs on ESF-CCS signal failure. This study is expected to provide insight into the development of a fault-tree model for network failures in digital I&C systems and the quantification of the risk effects of network failures for safety-critical information transmission in NPPs. - Highlights: • Network reliability modeling framework for digital I&C system in NPP is proposed. • Hazardous states of network protocol between GC and LC in ESF-CCS are identified. • Fault-tree model of ESF-CCS signal failure in ESF actuation condition is developed. • Risk effect of network failure on ESF-CCS signal failure is analyzed.

Corrections to "Connectivity-Based Reliable Multicast MAC Protocol for IEEE 802.11 Wireless LANs"

Directory of Open Access Journals (Sweden)

Choi Woo-Yong

2010-01-01

Full Text Available We have found the errors in the throughput formulae presented in our paper "Connectivity-based reliable multicast MAC protocol for IEEE 802.11 wireless LANs". We provide the corrected formulae and numerical results.

Inter-Vehicle Communication System Utilizing Autonomous Distributed Transmit Power Control

Science.gov (United States)

Hamada, Yuji; Sawa, Yoshitsugu; Goto, Yukio; Kumazawa, Hiroyuki

In ad-hoc network such as inter-vehicle communication (IVC) system, safety applications that vehicles broadcast the information such as car velocity, position and so on periodically are considered. In these applications, if there are many vehicles broadcast data in a communication area, congestion incurs a problem decreasing communication reliability. We propose autonomous distributed transmit power control method to keep high communication reliability. In this method, each vehicle controls its transmit power using feed back control. Furthermore, we design a communication protocol to realize the proposed method, and we evaluate the effectiveness of proposed method using computer simulation.

The impact of the Family Communication Coordinator (FCC) Protocol on the role stress of hospital chaplains.

Science.gov (United States)

Dodd-McCue, Diane; Tartaglia, Alexander

2005-01-01

The Family Communication Coordinator (FCC) Protocol was implemented to provide early family intervention and to facilitate effective communications during potential organ donation cases. Previous studies found the Protocol associated with improved donor outcome measures and with reduced role stress for ICU nurses caring for potential donors. The present study examines the impact of the Protocol on the perceived role stress of hospital chaplains serving as FCCs. All hospital chaplains serving as FCCs at an academic teaching hospital were surveyed. Their perceptions of job dimensions, role stress, job satisfaction, and commitment were measured; interviews and secondary data supplemented the surveys. The findings demonstrate that the FCC Protocol is associated with improved role stress, specifically role ambiguity and role conflict, among hospital chaplains serving as FCCs. Additionally, the findings suggest that satisfaction with the Protocol may be associated with experience with the Protocol.

78 FR 69018 - Improving the Resiliency of Mobile Wireless Communications Networks; Reliability and Continuity...

Science.gov (United States)

2013-11-18

... consumers value overall network reliability and quality in selecting mobile wireless service providers, they...-125] Improving the Resiliency of Mobile Wireless Communications Networks; Reliability and Continuity... (Reliability NOI) in 2011 to ``initiate a comprehensive examination of issues regarding the reliability...

Improved security detection strategy in quantum secure direct communication protocol based on four-particle Green-Horne-Zeilinger state

Energy Technology Data Exchange (ETDEWEB)

Li, Jian; Nie, Jin-Rui; Li, Rui-Fan [Beijing Univ. of Posts and Telecommunications, Beijing (China). School of Computer; Jing, Bo [Beijing Univ. of Posts and Telecommunications, Beijing (China). School of Computer; Beijing Institute of Applied Meteorology, Beijing (China). Dept. of Computer Science

2012-06-15

To enhance the efficiency of eavesdropping detection in the quantum secure direct communication protocol, an improved quantum secure direct communication protocol based on a four-particle Green-Horne-Zeilinger (GHZ) state is presented. In the protocol, the four-particle GHZ state is used to detect eavesdroppers, and quantum dense coding is used to encode the message. In the security analysis, the method of entropy theory is introduced, and two detection strategies are compared quantitatively by using the constraint between the information that the eavesdroppers can obtain and the interference that has been introduced. If the eavesdropper wants to obtain all the information, the detection rate of the quantum secure direct communication using an Einstein-Podolsky-Rosen (EPR) pair block will be 50% and the detection rate of the presented protocol will be 87%. At last, the security of the proposed protocol is discussed. The analysis results indicate that the protocol proposed is more secure than the others. (orig.)

Performance evaluation of secured DICOM image communication with next generation internet protocol IPv6

Science.gov (United States)

Yu, Fenghai; Zhang, Jianguo; Chen, Xiaomeng; Huang, H. K.

2005-04-01

Next Generation Internet (NGI) technology with new communication protocol IPv6 emerges as a potential solution for low-cost and high-speed networks for image data transmission. IPv6 is designed to solve many of the problems of the current version of IP (known as IPv4) with regard to address depletion, security, autoconfiguration, extensibility, and more. We choose CTN (Central Test Node) DICOM software developed by The Mallinckrodt Institute of Radiology to implement IPv6/IPv4 enabled DICOM communication software on different operating systems (Windows/Linux), and used this DICOM software to evaluate the performance of the IPv6/IPv4 enabled DICOM image communication with different security setting and environments. We compared the security communications of IPsec with SSL/TLS on different TCP/IP protocols (IPv6/IPv4), and find that there are some trade-offs to choose security solution between IPsec and SSL/TLS in the security implementation of IPv6/IPv4 communication networks.

Striding networks of inter-process communication based on TCP/IP protocol

International Nuclear Information System (INIS)

Lou Yi; Chen Haichun; Qian Jing; Chen Zhuomin

2004-01-01

A mode of process/thread communication between QNX and WINDOWS operating systems in isomerous computers is described. It is proved in practice to be an entirely feasible mode with high efficiency and reliability. A socket created by Socket API is used to communicate between two operating systems. (authors)

A Protocol for Bidirectional Quantum Secure Communication Based on Genuine Four-Particle Entangled States

International Nuclear Information System (INIS)

Gao Gan; Wang Liping

2010-01-01

By swapping the entanglement of genuine four-particle entangled states, we propose a bidirectional quantum secure communication protocol. The biggest merit of this protocol is that the information leakage does not exist. In addition, the ideas of the 'two-step' transmission and the block transmission are employed in this protocol. In order to analyze the security of the second sequence transmission, decoy states are used. (general)

MATLAB Simulation of RFID Communication Protocol for Sensor Data Acquisition

Directory of Open Access Journals (Sweden)

Soumen GHOSH

2015-05-01

Full Text Available Data acquisition processes the sampling and conditioning the signals that measure real world physical conditions such as temperature, pressure, flow etc. and convert the signal into in appropriate format for displaying and transmission to remote end. Now a days RFID i.e. Radio Frequency Identification plays a vital role in Data acquisition system. The present article proposes a smart DAS scheme containing RFID reader and Active tag. The data acquisition system is interfaced with tag through I2C bus. The reader communicates with tag following RFID communication protocol requesting to send the logged data which are refreshed and stored into tag memory periodically. The communication is simulated using MATLAB software successfully.

ABS-SmartComAgri: An Agent-Based Simulator of Smart Communication Protocols in Wireless Sensor Networks for Debugging in Precision Agriculture.

Science.gov (United States)

García-Magariño, Iván; Lacuesta, Raquel; Lloret, Jaime

2018-03-27

Smart communication protocols are becoming a key mechanism for improving communication performance in networks such as wireless sensor networks. However, the literature lacks mechanisms for simulating smart communication protocols in precision agriculture for decreasing production costs. In this context, the current work presents an agent-based simulator of smart communication protocols for efficiently managing pesticides. The simulator considers the needs of electric power, crop health, percentage of alive bugs and pesticide consumption. The current approach is illustrated with three different communication protocols respectively called (a) broadcast, (b) neighbor and (c) low-cost neighbor. The low-cost neighbor protocol obtained a statistically-significant reduction in the need of electric power over the neighbor protocol, with a very large difference according to the common interpretations about the Cohen's d effect size. The presented simulator is called ABS-SmartComAgri and is freely distributed as open-source from a public research data repository. It ensures the reproducibility of experiments and allows other researchers to extend the current approach.

Study on highly reliable digital communication technology of reactor nuclear measuring equipment

International Nuclear Information System (INIS)

Gu Pengfei; Huang Xiaojin

2007-01-01

To meet the need of highly reliable of reactor nuclear measuring equipment, in allusion to the idiographic request of nuclear measuring equipment, the actual technical development and the application in industrial field, we design a kind of redundancy communication net based on PROFIBUS, and a kind of communication interface module based on redundancy PROFIBUS communication, which link the nuclear measuring equipment and PROFIBUS communication net, and also lay a foundation for advanced research. (authors)

Test-retest reliability of a balance testing protocol with external perturbations in young healthy adults.

Science.gov (United States)

Robbins, Shawn M; Caplan, Ryan M; Aponte, Daniel I; St-Onge, Nancy

2017-10-01

External perturbations are utilized to challenge balance and mimic realistic balance threats in patient populations. The reliability of such protocols has not been established. The purpose was to examine test-retest reliability of balance testing with external perturbations. Healthy adults (n=34; mean age 23 years) underwent balance testing over two visits. Participants completed ten balance conditions in which the following parameters were combined: perturbation or non-perturbation, single or double leg, and eyes open or closed. Three trials were collected for each condition. Data were collected on a force plate and external perturbations were applied by translating the plate. Force plate center of pressure (CoP) data were summarized using 13 different CoP measures. Test-retest reliability was examined using intraclass correlation coefficients (ICC) and Bland-Altman plots. CoP measures of total speed and excursion in both anterior-posterior and medial-lateral directions generally had acceptable ICC values for perturbation conditions (ICC=0.46 to 0.87); however, many other CoP measures (e.g. range, area of ellipse) had unacceptable test-retest reliability (ICCbalance testing protocols that include external perturbations should be made to improve test-retest reliability and diminish learning including more extensive participant training and increasing the number of trials. CoP measures that consider all data points (e.g. total speed) are more reliable than those that only consider a few data points. Copyright © 2017 Elsevier B.V. All rights reserved.

Network protocol 'EPAP'; Network protokoru 'EPAP'

Energy Technology Data Exchange (ETDEWEB)

Kobori, T.; Fujita, F.; Iwamoto, S. [Fuji Electric Co. Ltd., Toyo (Japan)

2000-10-10

The Ethernet, a standard of information networks, has begun to be applied to the control local area network (LAN). To apply the Ethernet to the field level, Fuji Electric has newly developed the communication protocol 'Ethernet precision access protocol (EPAP)' in which a command/response method is structured on the user datagram protocol (UDP) to realize real time and high reliability. Further, we have implemented the EPAP on the bus interface module of the open PIO. This paper outlines the EPAP and its implementation. (author)

Impersonation attack on a quantum secure direct communication and authentication protocol with improvement

Science.gov (United States)

Amerimehr, Ali; Hadain Dehkordi, Massoud

2018-03-01

We analyze the security of a quantum secure direct communication and authentication protocol based on single photons. We first give an impersonation attack on the protocol. The cryptanalysis shows that there is a gap in the authentication procedure of the protocol so that an opponent can reveal the secret information by an undetectable attempt. We then propose an improvement for the protocol and show it closes the gap by applying a mutual authentication procedure. In the improved protocol single photons are transmitted once in a session, so it is easy to implement as the primary protocol. Furthermore, we use a novel technique for secret order rearrangement of photons by which not only quantum storage is eliminated also a secret key can be reused securely. So the new protocol is applicable in practical approaches like embedded system devices.

BTP: a Block Transfer Protocol for Delay Tolerant Wireless Sensor Networks

DEFF Research Database (Denmark)

Hansen, Morten Tranberg; Biagioni, Edoardo S.

2010-01-01

Wireless sensor networks that are energy-constrained must transmit and receive data as efficiently as possible.  If the transmission is delay tolerant, transferring blocks of accumulated data can be more efficient than transferring each sensed measurement as soon as it is available.  This paper...... proposes a Block Transfer Protocol (BTP) designed for efficient and reliable transmission in wireless sensor networks.  BTP reduces the time it takes to reliably transfer a block of packets compared to conventional link layer protocols, by piggybacking in data packets information about the transfer......, minimizing the number of acknowledgements needed for reliable transmission, and reducing the need for timeouts, which can substantially slow down communication when transmission is unreliable.  In addition, BTP improves reliability by handling false positive acknowledgements and by letting the receivers...

An efficient and reliable multi-hop geographical broadcast protocol in vehicular ad-hoc networks

NARCIS (Netherlands)

Rajendran, R.; Jongh, J. de

2013-01-01

In Intelligent Transportation Systems (ITS), disseminating warning messages in a timely and efficient way through wireless short-range communications can save many lives and reduce traffic congestion. A geographical broadcast protocol provides data delivery to specified geographical areas, using

Two-Layer Hierarchy Optimization Model for Communication Protocol in Railway Wireless Monitoring Networks

Directory of Open Access Journals (Sweden)

Xiaoping Ma

2018-01-01

Full Text Available The wireless monitoring system is always destroyed by the insufficient energy of the sensors in railway. Hence, how to optimize the communication protocol and extend the system lifetime is crucial to ensure the stability of system. However, the existing studies focused primarily on cluster-based or multihop protocols individually, which are ineffective in coping with the complex communication scenarios in the railway wireless monitoring system (RWMS. This study proposes a hybrid protocol which combines the cluster-based and multihop protocols (CMCP to minimize and balance the energy consumption in different sections of the RWMS. In the first hierarchy, the total energy consumption is minimized by optimizing the cluster quantities in the cluster-based protocol and the number of hops and the corresponding hop distances in the multihop protocol. In the second hierarchy, the energy consumption is balanced through rotating the cluster head (CH in the subnetworks and further optimizing the hops and the corresponding hop distances in the backbone network. On this basis, the system lifetime is maximized with the minimum and balance energy consumption among the sensors. Furthermore, the hybrid particle swarm optimization and genetic algorithm (PSO-GA are adopted to optimize the energy consumption from the two-layer hierarchy. Finally, the effectiveness of the proposed CMCP is verified in the simulation. The performances of the proposed CMCP in system lifetime, residual energy, and the corresponding variance are all superior to the LEACH protocol widely applied in the previous research. The effective protocol proposed in this study can facilitate the application of the wireless monitoring network in the railway system and enhance safety operation of the railway.

Standardised clients as assessors in a veterinary communication OSCE: a reliability and validity study.

Science.gov (United States)

Artemiou, E; Adams, C L; Hecker, K G; Vallevand, A; Violato, C; Coe, J B

2014-11-22

In human medicine, standardised patients (SP) have been shown to reliably and accurately assess learners' communication performance in high-stakes certification Objective Structured Clinical Examinations (OSCE), offering a feasible way to reduce the need for recruitment, time commitment and coordination of faculty assessors. In this study, we evaluated the use of standardised clients (SC) as a viable option for assessing veterinary students' communication performance. We designed a four-station, two-track communication skills OSCE. SC assessors used an adapted nine-item Liverpool Undergraduate Communication Assessment Scale (LUCAS). Faculty used a 21-item checklist derived from the Calgary-Cambridge Guide (CCG) and a five-point global rating scale. Participants were second year veterinary students (n=96). For the four stations, intrastation reliability (α) ranged from 0.63 to 0.82 for the LUCAS, and 0.73 to 0.87 for the CCG. The interstation reliability coefficients were 0.85 for the LUCAS and 0.89 for the CGG. The calculated Generalisability (G) coefficients were 0.62 for the LUCAS and 0.60 for the CGG. Supporting construct validity, SC and faculty assessors showed a significant correlation between the LUCAS and CCG total percent scores (r=0.45, PStudy results support that SC assessors offer a reliable and valid approach for assessing veterinary communication OSCE. British Veterinary Association.

Analysis of Pervasive Mobile Ad Hoc Routing Protocols

Science.gov (United States)

Qadri, Nadia N.; Liotta, Antonio

Mobile ad hoc networks (MANETs) are a fundamental element of pervasive networks and therefore, of pervasive systems that truly support pervasive computing, where user can communicate anywhere, anytime and on-the-fly. In fact, future advances in pervasive computing rely on advancements in mobile communication, which includes both infrastructure-based wireless networks and non-infrastructure-based MANETs. MANETs introduce a new communication paradigm, which does not require a fixed infrastructure - they rely on wireless terminals for routing and transport services. Due to highly dynamic topology, absence of established infrastructure for centralized administration, bandwidth constrained wireless links, and limited resources in MANETs, it is challenging to design an efficient and reliable routing protocol. This chapter reviews the key studies carried out so far on the performance of mobile ad hoc routing protocols. We discuss performance issues and metrics required for the evaluation of ad hoc routing protocols. This leads to a survey of existing work, which captures the performance of ad hoc routing algorithms and their behaviour from different perspectives and highlights avenues for future research.

Reliability of Broadcast Communications Under Sparse Random Linear Network Coding

OpenAIRE

Brown, Suzie; Johnson, Oliver; Tassi, Andrea

2018-01-01

Ultra-reliable Point-to-Multipoint (PtM) communications are expected to become pivotal in networks offering future dependable services for smart cities. In this regard, sparse Random Linear Network Coding (RLNC) techniques have been widely employed to provide an efficient way to improve the reliability of broadcast and multicast data streams. This paper addresses the pressing concern of providing a tight approximation to the probability of a user recovering a data stream protected by this kin...

IRR (Inter-Rater Reliability) of a COP (Classroom Observation Protocol)--A Critical Appraisal

Science.gov (United States)

Rui, Ning; Feldman, Jill M.

2012-01-01

Notwithstanding broad utility of COPs (classroom observation protocols), there has been limited documentation of the psychometric properties of even the most popular COPs. This study attempted to fill this void by closely examining the item and domain-level IRR (inter-rater reliability) of a COP that was used in a federally funded striving readers…

Effect of communication on the reliability of nuclear power plant control room operations - pre study

International Nuclear Information System (INIS)

Kettunen, Jari; Pyy, Pekka

1999-01-01

The objective of the study presented in this paper is to investigate communication practices and their impact on human reliability and plant safety in a nuclear power plant environment. The study aims at developing a general systems approach towards the issue. The ultimate goal of the study is to contribute to the development of probabilistic safety assessment methodologies in the area of communications and crew co-operation. This paper outlines the results of the pre-study. The study is based on the use and further development of different modelling techniques and the application of generic systems engineering as well as crew resource management (CRM) principles. The results so far include a concise literature review on communication and crew performance, a presentation of some potential theoretical concepts and approaches for studying communication in relation to organisational reliability, causal failure sequences and human failures mechanisms, and an introduction of a General Communications Model (GCM) that is presented as a promising approach for studying the reliability and adequacy of communication transactions. Finally, some observations and recommendation concerning next phases of the study are made (author) (ml)

Secure and Reliable Wireless Communications for Geological Repositories and Nuclear Facilities

International Nuclear Information System (INIS)

Twogood, R.

2015-01-01

There is an important need to develop new generation robust RF communication systems to support wireless communications and instrumentation control in geological repositories and nuclear facilities, such as nuclear power plants. Often these facilities have large metallic structures with electromagnetic (EM) transients from plant equipment. The ambient EMI/RFI harsh environment is responsible for degrading radio link bandwidth. Current communication systems often employ physical cables that are not only expensive to install, but deteriorate over time and are vulnerable to failures. Furthermore, conventional high-power narrowband walkie-talkies sometimes upset other electronics. On the other hand, high-quality reliable wireless communications between operators and automated control systems are critical in these facilities, as wireless sensors become more and more prevalent in these operations. In an effort to develop novel wireless communications systems, Dirac Solutions Inc. (DSI) in collaboration with Lawrence Livermore National Laboratory (LLNL), has developed high-quality ultra-wideband (UWB) hand-held communications systems that have proven to have excellent performance in ships and tunnels. The short pulse UWB RF technology, with bandwidths of many hundreds of MHz's, are non-interfering due to low average power. Furthermore, the UWB link has been shown to be highly reliable in the presence of other interfering signals. The DSI UWB communications systems can be adapted for applications in tunnels and nuclear power facilities for voice, data, and instrumentation control. In this paper we show examples of voice communication in ships with UWB walkie-talkies. We have developed novel modulation and demodulation techniques for short pulse UWB communications. The design is a low-power one and in a compact form. The communication units can be produced inexpensively in large quantities. A major application of these units might be their use by IAEA inspectors and

Emulation Platform for Cyber Analysis of Wireless Communication Network Protocols

Energy Technology Data Exchange (ETDEWEB)

Van Leeuwen, Brian P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Eldridge, John M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-11-01

Wireless networking and mobile communications is increasing around the world and in all sectors of our lives. With increasing use, the density and complexity of the systems increase with more base stations and advanced protocols to enable higher data throughputs. The security of data transported over wireless networks must also evolve with the advances in technologies enabling more capable wireless networks. However, means for analysis of the effectiveness of security approaches and implementations used on wireless networks are lacking. More specifically a capability to analyze the lower-layer protocols (i.e., Link and Physical layers) is a major challenge. An analysis approach that incorporates protocol implementations without the need for RF emissions is necessary. In this research paper several emulation tools and custom extensions that enable an analysis platform to perform cyber security analysis of lower layer wireless networks is presented. A use case of a published exploit in the 802.11 (i.e., WiFi) protocol family is provided to demonstrate the effectiveness of the described emulation platform.

Stochastic Petri nets for the reliability analysis of communication network applications with alternate-routing

International Nuclear Information System (INIS)

Balakrishnan, Meera; Trivedi, Kishor S.

1996-01-01

In this paper, we present a comparative reliability analysis of an application on a corporate B-ISDN network under various alternate-routing protocols. For simple cases, the reliability problem can be cast into fault-tree models and solved rapidly by means of known methods. For more complex scenarios, state space (Markov) models are required. However, generation of large state space models can get very labor intensive and error prone. We advocate the use of stochastic reward nets (a variant of stochastic Petri nets) for the concise specification, automated generation and solution of alternate-routing protocols in networks. This paper is written in a tutorial style so as to make it accessible to a large audience

Establishing rational networking using the DL04 quantum secure direct communication protocol

Science.gov (United States)

Qin, Huawang; Tang, Wallace K. S.; Tso, Raylin

2018-06-01

The first rational quantum secure direct communication scheme is proposed, in which we use the game theory with incomplete information to model the rational behavior of the participant, and give the strategy space and utility function. The rational participant can get his maximal utility when he performs the protocol faithfully, and then the Nash equilibrium of the protocol can be achieved. Compared to the traditional schemes, our scheme will be more practical in the presence of rational participant.

A Brief Survey of Media Access Control, Data Link Layer, and Protocol Technologies for Lunar Surface Communications

Science.gov (United States)

Wallett, Thomas M.

2009-01-01

This paper surveys and describes some of the existing media access control and data link layer technologies for possible application in lunar surface communications and the advanced wideband Direct Sequence Code Division Multiple Access (DSCDMA) conceptual systems utilizing phased-array technology that will evolve in the next decade. Time Domain Multiple Access (TDMA) and Code Division Multiple Access (CDMA) are standard Media Access Control (MAC) techniques that can be incorporated into lunar surface communications architectures. Another novel hybrid technique that is recently being developed for use with smart antenna technology combines the advantages of CDMA with those of TDMA. The relatively new and sundry wireless LAN data link layer protocols that are continually under development offer distinct advantages for lunar surface applications over the legacy protocols which are not wireless. Also several communication transport and routing protocols can be chosen with characteristics commensurate with smart antenna systems to provide spacecraft communications for links exhibiting high capacity on the surface of the Moon. The proper choices depend on the specific communication requirements.

The improvement of the connections reliability in a local communication system

International Nuclear Information System (INIS)

Buisson, J.; Sanchis, P.

1986-01-01

The local communication systems used in the management of the industrial processes must fulfil more severe conditions concerning the reliability and safety than those used in bureaucratics. After mentioning the specific requirements the solutions for the realization of a local industrial communication system are presented. Studies to develop an optical fibers coupling system for a linear network used for the transmission in a hostile medium are mentioned

Revised scoring and improved reliability for the Communication Patterns Questionnaire.

Science.gov (United States)

Crenshaw, Alexander O; Christensen, Andrew; Baucom, Donald H; Epstein, Norman B; Baucom, Brian R W

2017-07-01

The Communication Patterns Questionnaire (CPQ; Christensen, 1987) is a widely used self-report measure of couple communication behavior and is well validated for assessing the demand/withdraw interaction pattern, which is a robust predictor of poor relationship and individual outcomes (Schrodt, Witt, & Shimkowski, 2014). However, no studies have examined the CPQ's factor structure using analytic techniques sufficient by modern standards, nor have any studies replicated the factor structure using additional samples. Further, the current scoring system uses fewer than half of the total items for its 4 subscales, despite the existence of unused items that have content conceptually consistent with those subscales. These characteristics of the CPQ have likely contributed to findings that subscale scores are often troubled by suboptimal psychometric properties such as low internal reliability (e.g., Christensen, Eldridge, Catta-Preta, Lim, & Santagata, 2006). The present study uses exploratory and confirmatory factor analyses on 4 samples to reexamine the factor structure of the CPQ to improve scale score reliability and to determine if including more items in the subscales is warranted. Results indicate that a 3-factor solution (constructive communication and 2 demand/withdraw scales) provides the best fit for the data. That factor structure was confirmed in the replication samples. Compared with the original scales, the revised scales include additional items that expand the conceptual range of the constructs, substantially improve reliability of scale scores, and demonstrate stronger associations with relationship satisfaction and sensitivity to change in therapy. Implications for research and treatment are discussed. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

BAVP: Blockchain-Based Access Verification Protocol in LEO Constellation Using IBE Keys

Directory of Open Access Journals (Sweden)

Songjie Wei

2018-01-01

Full Text Available LEO constellation has received intensive research attention in the field of satellite communication. The existing centralized authentication protocols traditionally used for MEO/GEO satellite networks cannot accommodate LEO satellites with frequent user connection switching. This paper proposes a fast and efficient access verification protocol named BAVP by combining identity-based encryption and blockchain technology. Two different key management schemes with IBE and blockchain, respectively, are investigated, which further enhance the authentication reliability and efficiency in LEO constellation. Experiments on OPNET simulation platform evaluate and demonstrate the effectiveness, reliability, and fast-switching efficiency of the proposed protocol. For LEO networks, BAVP surpasses the well-known existing solutions with significant advantages in both performance and scalability which are supported by theoretical analysis and simulation results.

Quantum broadcast communication and authentication protocol with a quantum one-time pad

International Nuclear Information System (INIS)

Chang Yan; Xu Chun-Xiang; Zhang Shi-Bin; Yan Li-Li

2014-01-01

A quantum broadcast communication and authentication protocol with a quantum one-time pad based on the Greenberger—Horne—Zeilinger state is proposed. A binary string is used to express the identity of the receiver, which is encoded as a single sequence of photons. The encoded photon sequence acts as a detection sequence and implements authentication. An XOR operation serves as a one-time pad and is used to ensure the security of the protocol. The binary string is reused even in a noisy channel and proves to be unconditionally secure. In contrast with the protocols proposed by Wang et al. [Chin. Phys. 16 1868 (2007)] and Yang et al. [Chin. Phys. B 19 070304 (2010)], the protocol in this study implements the identity authentication with a reusable binary string; no hash function or local unitary operation is used. The protocol in this study is also easier to implement and highly efficient without losing security. (general)

Assessing physiotherapists' communication skills for promoting patient autonomy for self-management: reliability and validity of the communication evaluation in rehabilitation tool.

Science.gov (United States)

Murray, Aileen; Hall, Amanda; Williams, Geoffrey C; McDonough, Suzanne M; Ntoumanis, Nikos; Taylor, Ian; Jackson, Ben; Copsey, Bethan; Hurley, Deirdre A; Matthews, James

2018-02-27

To assess the inter-rater reliability and concurrent validity of the Communication Evaluation in Rehabilitation Tool, which aims to externally assess physiotherapists competency in using Self-Determination Theory-based communication strategies in practice. Audio recordings of initial consultations between 24 physiotherapists and 24 patients with chronic low back pain in four hospitals in Ireland were obtained as part of a larger randomised controlled trial. Three raters, all of whom had Ph.Ds in psychology and expertise in motivation and physical activity, independently listened to the 24 audio recordings and completed the 18-item Communication Evaluation in Rehabilitation Tool. Inter-rater reliability between all three raters was assessed using intraclass correlation coefficients. Concurrent validity was assessed using Pearson's r correlations with a reference standard, the Health Care Climate Questionnaire. The total score for the Communication Evaluation in Rehabilitation Tool is an average of all 18 items. Total scores demonstrated good inter-rater reliability (Intraclass Correlation Coefficient (ICC) = 0.8) and concurrent validity with the Health Care Climate Questionnaire total score (range: r = 0.7-0.88). Item-level scores of the Communication Evaluation in Rehabilitation Tool identified five items that need improvement. Results provide preliminary evidence to support future use and testing of the Communication Evaluation in Rehabilitation Tool. Implications for Rehabilitation Promoting patient autonomy is a learned skill and while interventions exist to train clinicians in these skills there are no tools to assess how well clinicians use these skills when interacting with a patient. The lack of robust assessment has severe implications regarding both the fidelity of clinician training packages and resulting outcomes for promoting patient autonomy. This study has developed a novel measurement tool Communication Evaluation in Rehabilitation Tool and a

Performance Analysis of an Enhanced PRMA-HS Protocol for LEO Satellite Communication

Institute of Scientific and Technical Information of China (English)

ZHUO Yong-ning; YAN Shao-hu; WU Shi-qi

2005-01-01

The packet reservation multiple access with hindering state (PRMA-HS) is a protocol suitable for LEO satellite mobile communication. Although working well with light system payload (amount of user terminals), the protocol imposes high channel congestion on system with heavy payload, thus degrades the system's quality of service. To controlling the channel congestion, a scheme of enhanced PRMA-HS protocol is proposed, which aims to reduce the collision of voice packets by adopting a mechanism of access control. Through theoretic analysis, the system's mathematic model is presented and the packet drop probability of the scheme is deduced. To testify the performance of the scheme, a simulation is performed and the results support our analysis.

A high performance totally ordered multicast protocol

Science.gov (United States)

Montgomery, Todd; Whetten, Brian; Kaplan, Simon

1995-01-01

This paper presents the Reliable Multicast Protocol (RMP). RMP provides a totally ordered, reliable, atomic multicast service on top of an unreliable multicast datagram service such as IP Multicasting. RMP is fully and symmetrically distributed so that no site bears un undue portion of the communication load. RMP provides a wide range of guarantees, from unreliable delivery to totally ordered delivery, to K-resilient, majority resilient, and totally resilient atomic delivery. These QoS guarantees are selectable on a per packet basis. RMP provides many communication options, including virtual synchrony, a publisher/subscriber model of message delivery, an implicit naming service, mutually exclusive handlers for messages, and mutually exclusive locks. It has commonly been held that a large performance penalty must be paid in order to implement total ordering -- RMP discounts this. On SparcStation 10's on a 1250 KB/sec Ethernet, RMP provides totally ordered packet delivery to one destination at 842 KB/sec throughput and with 3.1 ms packet latency. The performance stays roughly constant independent of the number of destinations. For two or more destinations on a LAN, RMP provides higher throughput than any protocol that does not use multicast or broadcast.

Implementation and Analysis of Real-Time Streaming Protocols.

Science.gov (United States)

Santos-González, Iván; Rivero-García, Alexandra; Molina-Gil, Jezabel; Caballero-Gil, Pino

2017-04-12

Communication media have become the primary way of interaction thanks to the discovery and innovation of many new technologies. One of the most widely used communication systems today is video streaming, which is constantly evolving. Such communications are a good alternative to face-to-face meetings, and are therefore very useful for coping with many problems caused by distance. However, they suffer from different issues such as bandwidth limitation, network congestion, energy efficiency, cost, reliability and connectivity. Hence, the quality of service and the quality of experience are considered the two most important issues for this type of communication. This work presents a complete comparative study of two of the most used protocols of video streaming, Real Time Streaming Protocol (RTSP) and the Web Real-Time Communication (WebRTC). In addition, this paper proposes two new mobile applications that implement those protocols in Android whose objective is to know how they are influenced by the aspects that most affect the streaming quality of service, which are the connection establishment time and the stream reception time. The new video streaming applications are also compared with the most popular video streaming applications for Android, and the experimental results of the analysis show that the developed WebRTC implementation improves the performance of the most popular video streaming applications with respect to the stream packet delay.

Gateway-Assisted Retransmission for Lightweight and Reliable IoT Communications.

Science.gov (United States)

Chang, Hui-Ling; Wang, Cheng-Gang; Wu, Mong-Ting; Tsai, Meng-Hsun; Lin, Chia-Ying

2016-09-22

Message Queuing Telemetry Transport for Sensor Networks (MQTT-SN) and Constrained Application Protocol (CoAP) are two protocols supporting publish/subscribe models for IoT devices to publish messages to interested subscribers. Retransmission mechanisms are introduced to compensate for the lack of data reliability. If the device does not receive the acknowledgement (ACK) before retransmission timeout (RTO) expires, the device will retransmit data. Setting an appropriate RTO is important because the delay may be large or retransmission may be too frequent when the RTO is inappropriate. We propose a Gateway-assisted CoAP (GaCoAP) to dynamically compute RTO for devices. Simulation models are proposed to investigate the performance of GaCoAP compared with four other methods. The experiment results show that GaCoAP is more suitable for IoT devices.

Intra-rater and inter-rater reliability of the standardized ultrasound protocol for assessing subacromial structures

DEFF Research Database (Denmark)

Hougs Kjær, Birgitte; Ellegaard, Karen; Wieland, Ina

2017-01-01

BACKGROUND: US-examinations related to shoulder impingement (SI) often vary due to methodological differences, examiner positions, transducers, and recording parameters. Reliable US protocols for examination of different structures related to shoulder impingement are therefore needed. OBJECTIVES...... of the supraspinatus tendon (SUPRA) and subacromial subdeltoid (SASD) bursa in two imaging positions, and the acromial humeral distance (AHD) in one position. Additionally, agreement on dynamic impingement (DI) examination was performed. The intra- and inter-rater reliability was carried out on the same day...

The Communication Function Classification System: cultural adaptation, validity, and reliability of the Farsi version for patients with cerebral palsy.

Science.gov (United States)

Soleymani, Zahra; Joveini, Ghodsiye; Baghestani, Ahmad Reza

2015-03-01

This study developed a Farsi language Communication Function Classification System and then tested its reliability and validity. Communication Function Classification System is designed to classify the communication functions of individuals with cerebral palsy. Up until now, there has been no instrument for assessment of this communication function in Iran. The English Communication Function Classification System was translated into Farsi and cross-culturally modified by a panel of experts. Professionals and parents then assessed the content validity of the modified version. A backtranslation of the Farsi version was confirmed by the developer of the English Communication Function Classification System. Face validity was assessed by therapists and parents of 10 patients. The Farsi Communication Function Classification System was administered to 152 individuals with cerebral palsy (age, 2 to 18 years; median age, 10 years; mean age, 9.9 years; standard deviation, 4.3 years). Inter-rater reliability was analyzed between parents, occupational therapists, and speech and language pathologists. The test-retest reliability was assessed for 75 patients with a 14 day interval between tests. The inter-rater reliability of the Communication Function Classification System was 0.81 between speech and language pathologists and occupational therapists, 0.74 between parents and occupational therapists, and 0.88 between parents and speech and language pathologists. The test-retest reliability was 0.96 for occupational therapists, 0.98 for speech and language pathologists, and 0.94 for parents. The findings suggest that the Farsi version of Communication Function Classification System is a reliable and valid measure that can be used in clinical settings to assess communication function in patients with cerebral palsy. Copyright © 2015 Elsevier Inc. All rights reserved.

Development of Information Assurance Protocol for Low Bandwidth Nanosatellite Communications

Science.gov (United States)

2017-09-01

14. SUBJECT TERMS commercial off-the-shelf technology , nanosatellites, CubeSat, encrypted communications 15. NUMBER OF PAGES 161 16. PRICE...integrate with several physical layer technologies . While this protocol does provide some additional functionality at a lower cost, it is limited to...G. S. Vernam, “Secret signaling system.” U.S. Patent U.S. 1310719 A, 22 July 1919. [22] D. Kahn, Codebreakers: The Story of Secret Writing, New

Gateway-Assisted Retransmission for Lightweight and Reliable IoT Communications

Directory of Open Access Journals (Sweden)

Hui-Ling Chang

2016-09-01

Full Text Available Message Queuing Telemetry Transport for Sensor Networks (MQTT-SN and Constrained Application Protocol (CoAP are two protocols supporting publish/subscribe models for IoT devices to publish messages to interested subscribers. Retransmission mechanisms are introduced to compensate for the lack of data reliability. If the device does not receive the acknowledgement (ACK before retransmission timeout (RTO expires, the device will retransmit data. Setting an appropriate RTO is important because the delay may be large or retransmission may be too frequent when the RTO is inappropriate. We propose a Gateway-assisted CoAP (GaCoAP to dynamically compute RTO for devices. Simulation models are proposed to investigate the performance of GaCoAP compared with four other methods. The experiment results show that GaCoAP is more suitable for IoT devices.

Quantum direct communication protocol strengthening against Pavičić’s attack

Science.gov (United States)

Zhang, Bo; Shi, Wei-Xu; Wang, Jian; Tang, Chao-Jing

2015-12-01

A quantum circuit providing an undetectable eavesdropping of information in message mode, which compromises all two-state ψ-ϕ quantum direct communication (QDC) protocols, has been recently proposed by Pavičić [Phys. Rev. A 87 (2013) 042326]. A modification of the protocol’s control mode is proposed, which improves users’ 25% detection probability of Eve to 50% at best, as that in ping-pong protocol. The modification also improves the detection probability of Wójcik’s attack [Phys. Rev. Lett 90 (2003) 157901] to 75% at best. The resistance against man-in-the-middle (MITM) attack as well as the discussion of security for four Bell state protocols is presented. As a result, the protocol security is strengthened both theoretically and practically, and quantum advantage of superdense coding is restored.

Generating Models of Infinite-State Communication Protocols Using Regular Inference with Abstraction

Science.gov (United States)

Aarts, Fides; Jonsson, Bengt; Uijen, Johan

In order to facilitate model-based verification and validation, effort is underway to develop techniques for generating models of communication system components from observations of their external behavior. Most previous such work has employed regular inference techniques which generate modest-size finite-state models. They typically suppress parameters of messages, although these have a significant impact on control flow in many communication protocols. We present a framework, which adapts regular inference to include data parameters in messages and states for generating components with large or infinite message alphabets. A main idea is to adapt the framework of predicate abstraction, successfully used in formal verification. Since we are in a black-box setting, the abstraction must be supplied externally, using information about how the component manages data parameters. We have implemented our techniques by connecting the LearnLib tool for regular inference with the protocol simulator ns-2, and generated a model of the SIP component as implemented in ns-2.

Revisiting Frequency Reuse towards Supporting Ultra-Reliable Ubiquitous-Rate Communication

DEFF Research Database (Denmark)

Park, Jihong; Kim, Dong Min; Popovski, Petar

2017-01-01

One of the goals of 5G wireless systems stated by the NGMN alliance is to provide moderate rates (50+ Mbps) everywhere and with very high reliability. We term this service Ultra-Reliable Ubiquitous-Rate Communication (UR2C). This paper investigates the role of frequency reuse in supporting UR2C...... in the downlink. To this end, two frequency reuse schemes are considered: user-specific frequency reuse (FRu) and BS-specific frequency reuse (FRb). For a given unit frequency channel, FRu reduces the number of serving user equipments (UEs), whereas FRb directly decreases the number of interfering base stations...

WEAMR — A Weighted Energy Aware Multipath Reliable Routing Mechanism for Hotline-Based WSNs

Directory of Open Access Journals (Sweden)

Ki-Hyung Kim

2013-05-01

Full Text Available Reliable source to sink communication is the most important factor for an efficient routing protocol especially in domains of military, healthcare and disaster recovery applications. We present weighted energy aware multipath reliable routing (WEAMR, a novel energy aware multipath routing protocol which utilizes hotline-assisted routing to meet such requirements for mission critical applications. The protocol reduces the number of average hops from source to destination and provides unmatched reliability as compared to well known reactive ad hoc protocols i.e., AODV and AOMDV. Our protocol makes efficient use of network paths based on weighted cost calculation and intelligently selects the best possible paths for data transmissions. The path cost calculation considers end to end number of hops, latency and minimum energy node value in the path. In case of path failure path recalculation is done efficiently with minimum latency and control packets overhead. Our evaluation shows that our proposal provides better end-to-end delivery with less routing overhead and higher packet delivery success ratio compared to AODV and AOMDV. The use of multipath also increases overall life time of WSN network using optimum energy available paths between sender and receiver in WDNs.

Field Programmable Gate Array Reliability Analysis Guidelines for Launch Vehicle Reliability Block Diagrams

Science.gov (United States)

Al Hassan, Mohammad; Britton, Paul; Hatfield, Glen Spencer; Novack, Steven D.

2017-01-01

Field Programmable Gate Arrays (FPGAs) integrated circuits (IC) are one of the key electronic components in today's sophisticated launch and space vehicle complex avionic systems, largely due to their superb reprogrammable and reconfigurable capabilities combined with relatively low non-recurring engineering costs (NRE) and short design cycle. Consequently, FPGAs are prevalent ICs in communication protocols and control signal commands. This paper will identify reliability concerns and high level guidelines to estimate FPGA total failure rates in a launch vehicle application. The paper will discuss hardware, hardware description language, and radiation induced failures. The hardware contribution of the approach accounts for physical failures of the IC. The hardware description language portion will discuss the high level FPGA programming languages and software/code reliability growth. The radiation portion will discuss FPGA susceptibility to space environment radiation.

Reliable and energy-efficient communications for wireless biomedical implant systems.

Science.gov (United States)

Ntouni, Georgia D; Lioumpas, Athanasios S; Nikita, Konstantina S

2014-11-01

Implant devices are used to measure biological parameters and transmit their results to remote off-body devices. As implants are characterized by strict requirements on size, reliability, and power consumption, applying the concept of cooperative communications to wireless body area networks offers several benefits. In this paper, we aim to minimize the power consumption of the implant device by utilizing on-body wearable devices, while providing the necessary reliability in terms of outage probability and bit error rate. Taking into account realistic power considerations and wireless propagation environments based on the IEEE P802.l5 channel model, an exact theoretical analysis is conducted for evaluating several communication scenarios with respect to the position of the wearable device and the motion of the human body. The derived closed-form expressions are employed toward minimizing the required transmission power, subject to a minimum quality-of-service requirement. In this way, the complexity and power consumption are transferred from the implant device to the on-body relay, which is an efficient approach since they can be easily replaced, in contrast to the in-body implants.

Are wearable devices ready for HTTPS? Measuring the cost of secure communication protocols on wearable devices

OpenAIRE

Kolamunna, Harini; Chauhan, Jagmohan; Hu, Yining; Thilakarathna, Kanchana; Perino, Diego; Makaroff, Dwight; Seneviratne, Aruna

2016-01-01

The majority of available wearable devices require communication with Internet servers for data analysis and storage, and rely on a paired smartphone to enable secure communication. However, wearable devices are mostly equipped with WiFi network interfaces, enabling direct communication with the Internet. Secure communication protocols should then run on these wearables itself, yet it is not clear if they can be efficiently supported. In this paper, we show that wearable devices are ready for...

Monitoring of offshore wind farm using reliable communication

Energy Technology Data Exchange (ETDEWEB)

Sharma, K.G.; Gajranib, K.; Bhargavac, A. [Rajasthan Technical Univ.. Dept. of Electrical Engineering, Kota (India)

2012-07-01

Due to rapid exhaustion of fossil fuels, new renewable technologies for electricity generation are insisted upon to meet the continuous growing demand of energy all across the globe. Wind energy as a green energy is a favorable option, among other available renewable sources. The offshore wind farm capacity is growing rapidly, but it's uncertain and intermittent nature offers great challenges to power system engineers. The cost of repair and down time, results into extensive damage and reduced profitability. This necessitates the requirement of fast and reliable communication network for the monitoring and controlling of the wind farm. In this paper, we have proposed the communication network for medium offshore wind farm (160MW). The wind farm consists of four clusters; each cluster comprises of 10 Wind Turbines (WTs), each of capacity 4MW. A WT can be represented by nine logical nodes according to IEC-61400-25 standard. The functions of logical nodes are modeled in terms of analogue /status/control information. The wind farm has been modeled in OPNET modeler and the performance of the communication network is evaluated in terms of End to End delay and packet drop, using Synchronous Optical NETwork (SONET) standard. (Author)

Monitoring of offshore wind farm using reliable communication

Energy Technology Data Exchange (ETDEWEB)

Sharma, K G; Gajranib, K; Bhargavac, A [Rajasthan Technical Univ. Dept. of Electrical Engineering, Kota (India)

2012-07-01

Due to rapid exhaustion of fossil fuels, new renewable technologies for electricity generation are insisted upon to meet the continuous growing demand of energy all across the globe. Wind energy as a green energy is a favorable option, among other available renewable sources. The offshore wind farm capacity is growing rapidly, but it's uncertain and intermittent nature offers great challenges to power system engineers. The cost of repair and down time, results into extensive damage and reduced profitability. This necessitates the requirement of fast and reliable communication network for the monitoring and controlling of the wind farm. In this paper, we have proposed the communication network for medium offshore wind farm (160MW). The wind farm consists of four clusters; each cluster comprises of 10 Wind Turbines (WTs), each of capacity 4MW. A WT can be represented by nine logical nodes according to IEC-61400-25 standard. The functions of logical nodes are modeled in terms of analogue /status/control information. The wind farm has been modeled in OPNET modeler and the performance of the communication network is evaluated in terms of End to End delay and packet drop, using Synchronous Optical NETwork (SONET) standard. (Author)

A Review of Vehicle to Vehicle Communication Protocols for VANETs in the Urban Environment

Directory of Open Access Journals (Sweden)

Irshad Ahmed Abbasi

2018-01-01

Full Text Available Vehicular Ad-hoc Networks (VANETs have been gaining significant attention from the research community due to their increasing importance for building an intelligent transportation system. The characteristics of VANETs, such as high mobility, network partitioning, intermittent connectivity and obstacles in city environments, make routing a challenging task. Due to these characteristics of VANETs, the performance of a routing protocol is degraded. The position-based routing is considered to be the most significant approach in VANETs. In this paper, we present a brief review of most significant position based unicast routing protocols designed for vehicle to vehicle communications in the urban environment. We provide them with their working features for exchanging information between vehicular nodes. We describe their pros and cons. This study also provides a comparison of the vehicle to vehicle communication based routing protocols. The comparative study is based on some significant factors such as mobility, traffic density, forwarding techniques and method of junction selection mechanism, and strategy used to handle a local optimum situation. It also provides the simulation based study of existing dynamic junction selection routing protocols and a static junction selection routing protocol. It provides a profound insight into the routing techniques suggested in this area and the most valuable solutions to advance VANETs. More importantly, it can be used as a source of references to other researchers in finding literature that is relevant to routing in VANETs.

The reliability of a modified Kalamazoo Consensus Statement Checklist for assessing the communication skills of multidisciplinary clinicians in the simulated environment.

Science.gov (United States)

Peterson, Eleanor B; Calhoun, Aaron W; Rider, Elizabeth A

2014-09-01

With increased recognition of the importance of sound communication skills and communication skills education, reliable assessment tools are essential. This study reports on the psychometric properties of an assessment tool based on the Kalamazoo Consensus Statement Essential Elements Communication Checklist. The Gap-Kalamazoo Communication Skills Assessment Form (GKCSAF), a modified version of an existing communication skills assessment tool, the Kalamazoo Essential Elements Communication Checklist-Adapted, was used to assess learners in a multidisciplinary, simulation-based communication skills educational program using multiple raters. 118 simulated conversations were available for analysis. Internal consistency and inter-rater reliability were determined by calculating a Cronbach's alpha score and intra-class correlation coefficients (ICC), respectively. The GKCSAF demonstrated high internal consistency with a Cronbach's alpha score of 0.844 (faculty raters) and 0.880 (peer observer raters), and high inter-rater reliability with an ICC of 0.830 (faculty raters) and 0.89 (peer observer raters). The Gap-Kalamazoo Communication Skills Assessment Form is a reliable method of assessing the communication skills of multidisciplinary learners using multi-rater methods within the learning environment. The Gap-Kalamazoo Communication Skills Assessment Form can be used by educational programs that wish to implement a reliable assessment and feedback system for a variety of learners. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

The construction of distant total distributed measuring and controlling system based on RS-232 communication

International Nuclear Information System (INIS)

Shi Chengying; Li Tiantuo; Zhu Wenkai; Zhang Quanhu

1999-01-01

The author discusses the construction of distant total distributed measuring and controlling system based on RS-232 communication. The merits of this system are simple construction, reliable performance, big communication distance, and wide covering range. The system fits in with application in radiation environment. The author also discusses the system's hardware equipment and communication protocol

The reliability of a single protocol to determine endothelial, microvascular and autonomic functions in adolescents.

Science.gov (United States)

Bond, Bert; Williams, Craig A; Barker, Alan R

2017-11-01

Impairments in macrovascular, microvascular and autonomic function are present in asymptomatic youths with clustered cardiovascular disease risk factors. This study determines the within-day reliability and between-day reliability of a single protocol to non-invasively assess these outcomes in adolescents. Forty 12- to 15-year-old adolescents (20 boys) visited the laboratory in a fasted state on two occasions, approximately 1 week apart. One hour after a standardized cereal breakfast, macrovascular function was determined via flow-mediated dilation (FMD). Heart rate variability (root mean square of successive R-R intervals; RMSSD) was determined from the ECG-gated ultrasound images acquired during the FMD protocol prior to cuff occlusion. Microvascular function was simultaneously quantified as the peak (PRH) and total (TRH) hyperaemic response to occlusion in the cutaneous circulation of the forearm via laser Doppler imaging. To address within-day reliability, a subset of twenty adolescents (10 boys) repeated these measures 90 min afterwards on one occasion. The within-day typical error and between-day typical error expressed as a coefficient of variation of these outcomes are as follows: ratio-scaled FMD, 5·1% and 10·6%; allometrically scaled FMD, 4·4% and 9·4%; PRH, 11% and 13·3%; TRH, 29·9% and 23·1%; and RMSSD, 17·6% and 17·6%. The within- and between-day test-retest correlation coefficients for these outcomes were all significant (r > 0·54 for all). Macrovascular, microvascular and autonomic functions can be simultaneously and non-invasively determined in adolescents using a single protocol with an appropriate degree of reproducibility. Determining these outcomes may provide greater understanding of the progression of cardiovascular disease and aid early intervention. © 2016 Scandinavian Society of Clinical Physiology and Nuclear Medicine. Published by John Wiley & Sons Ltd.

Reliability of single aliquot regenerative protocol (SAR) for dose estimation in quartz at different burial temperatures: A simulation study

International Nuclear Information System (INIS)

Koul, D.K.; Pagonis, V.; Patil, P.

2016-01-01

The single aliquot regenerative protocol (SAR) is a well-established technique for estimating naturally acquired radiation doses in quartz. This simulation work examines the reliability of SAR protocol for samples which experienced different ambient temperatures in nature in the range of −10 to 40 °C. The contribution of various experimental variables used in SAR protocols to the accuracy and precision of the method is simulated for different ambient temperatures. Specifically the effects of paleo-dose, test dose, pre-heating temperature and cut-heat temperature on the accuracy of equivalent dose (ED) estimation are simulated by using random combinations of the concentrations of traps and centers using a previously published comprehensive quartz model. The findings suggest that the ambient temperature has a significant bearing on the reliability of natural dose estimation using SAR protocol, especially for ambient temperatures above 0 °C. The main source of these inaccuracies seems to be thermal sensitization of the quartz samples caused by the well-known thermal transfer of holes between luminescence centers in quartz. The simulations suggest that most of this inaccuracy in the dose estimation can be removed by delivering the laboratory doses in pulses (pulsed irradiation procedures). - Highlights: • Ambient temperatures affect the reliability of SAR. • It overestimates the dose with increase in burial temperature and burial time periods. • Elevated temperature irradiation does not correct for these overestimations. • Inaccuracies in dose estimation can be removed by incorporating pulsed irradiation procedures.

Development of Network Protocol for the Integrated Safety System

Energy Technology Data Exchange (ETDEWEB)

Park, S. W.; Baek, J. I.; Lee, S. H.; Park, C. S.; Park, K. H.; Shin, J. M. [Hannam Univ., Daejeon (Korea, Republic of)

2007-06-15

Communication devices in the safety system of nuclear power plants are distinguished from those developed for commercial purposes in terms of a strict requirement of safety. The concept of safety covers the determinability, the reliability, and the separation/isolation to prevent the undesirable interactions among devices. The safety also requires that these properties be never proof less. Most of the current commercialized communication products rarely have the safety properties. Moreover, they can be neither verified nor validated to satisfy the safety property of implementation process. This research proposes the novel architecture and protocol of a data communication network for the safety system in nuclear power plants.

Development of Network Protocol for the Integrated Safety System

International Nuclear Information System (INIS)

Park, S. W.; Baek, J. I.; Lee, S. H.; Park, C. S.; Park, K. H.; Shin, J. M.

2007-06-01

Communication devices in the safety system of nuclear power plants are distinguished from those developed for commercial purposes in terms of a strict requirement of safety. The concept of safety covers the determinability, the reliability, and the separation/isolation to prevent the undesirable interactions among devices. The safety also requires that these properties be never proof less. Most of the current commercialized communication products rarely have the safety properties. Moreover, they can be neither verified nor validated to satisfy the safety property of implementation process. This research proposes the novel architecture and protocol of a data communication network for the safety system in nuclear power plants

Developing Reliable Telemedicine Platforms with Unreliable and Limited Communication Bandwidth

Science.gov (United States)

2017-10-01

AFRL-SA-WP-TR-2017-0019 Developing Reliable Telemedicine Platforms with Unreliable and Limited Communication Bandwidth Peter F...Wright-Patterson AFB, OH 45433-7913 DISTRIBUTION STATEMENT A. Approved for public release. Distribution is unlimited. STINFO COPY NOTICE AND...invention that may relate to them. Qualified requestors may obtain copies of this report from the Defense Technical Information Center (DTIC) (http

A Generic Communication Protocol for Remote Laboratories: an Implementation on e-lab

Energy Technology Data Exchange (ETDEWEB)

Henriques, Rafael B.; Fernandes, H.; Duarte, Andre S.; Pereira, Tiago; Fortunato, Joao [Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal); Pereira, Jose [Linkare TI - Tecnologias de Informacao Lda, Lisboa (Portugal); Dias, Francisco [Instituto Superior Tecnico, Universidade de Lisboa, 1049-001 Lisboa (Portugal)

2015-07-01

The remote laboratories at IST (Instituto Superior Tecnico), e-lab, serve as a valuable tool for education and training based on remote control technologies. Due to the high number and increase of remotely operated experiments a generic protocol was developed to perform the communication between the software driver and the respective experimental setup in an easier and more unified way. The training in these fields of students and personnel can take advantage of such infrastructure with the purpose of deploying new experiments in a faster way. More than 10 experiments using the generic protocol are available on-line in a 24 x 7 way. (authors)

An Efficient Causal Group Communication Protocol for Free Scale Peer-to-Peer Networks

Directory of Open Access Journals (Sweden)

Grigory Evropeytsev

2016-08-01

Full Text Available In peer-to-peer (P2P overlay networks, a group of n (≥2 peer processes have to cooperate with each other. Each peer sends messages to every peer and receives messages from every peer in a group. In group communications, each message sent by a peer is required to be causally delivered to every peer. Most of the protocols designed to ensure causal message order are designed for networks with a plain architecture. These protocols can be adapted to use in free scale and hierarchical topologies; however, the amount of control information is O(n, where n is the number of peers in the system. Some protocols are designed for a free scale or hierarchical networks, but in general they force the whole system to accomplish the same order viewed by a super peer. In this paper, we present a protocol that is specifically designed to work with a free scale peer-to-peer network. By using the information about the network’s architecture and by representing message dependencies on a bit level, the proposed protocol ensures causal message ordering without enforcing super peers order. The designed protocol is simulated and compared with the Immediate Dependency Relation and the Dependency Sequences protocols to show its lower overhead.

Using Generalizability Theory to Assess the Score Reliability of Communication Skills of Dentistry Students

Science.gov (United States)

Uzun, N. Bilge; Aktas, Mehtap; Asiret, Semih; Yormaz, Seha

2018-01-01

The goal of this study is to determine the reliability of the performance points of dentistry students regarding communication skills and to examine the scoring reliability by generalizability theory in balanced random and fixed facet (mixed design) data, considering also the interactions of student, rater and duty. The study group of the research…

Protocol Implementation Generator

DEFF Research Database (Denmark)

Carvalho Quaresma, Jose Nuno; Probst, Christian W.

2010-01-01

Users expect communication systems to guarantee, amongst others, privacy and integrity of their data. These can be ensured by using well-established protocols; the best protocol, however, is useless if not all parties involved in a communication have a correct implementation of the protocol and a...... Generator framework based on the LySatool and a translator from the LySa language into C or Java....... necessary tools. In this paper, we present the Protocol Implementation Generator (PiG), a framework that can be used to add protocol generation to protocol negotiation, or to easily share and implement new protocols throughout a network. PiG enables the sharing, verification, and translation...

On a User-Centric Base Station Cooperation Scheme for Reliable Communications

DEFF Research Database (Denmark)

Kim, Dong Min; Thomsen, Henning; Popovski, Petar

2017-01-01

In this paper, we describe CoMP2flex, a user-centric base station (BS) cooperation scheme that provides improvements in reliability of both uplink (UL) and downlink (DL) communications of wireless cellular networks. CoMP2flex supports not only cooperation of two BSs with same direction of traffic...

Control Strategies for Improving Energy Efficiency and Reliability in Autonomous Microgrids with Communication Constraints

Directory of Open Access Journals (Sweden)

Francisco Martins Portelinha Júnior

2017-09-01

Full Text Available Microgrids are a feasible path to deploy smart grids, an intelligent and highly automated power system. Their operation demands a dedicated communication infrastructure to manage, control and monitor the intermittent sources of energy and loads. Therefore, smart devices will be connected to support the growth of grid smartness increasing the dependency on communication networks, which consumes a high amount of power. In an energy-limited scenario, one of the main issues is to enhance the power supply time. Therefore, this paper proposes a hybrid methodology for microgrid energy management, integrated with a communication infrastructure to improve and to optimize islanded microgrid operation at maximum energy efficiency. The hybrid methodology applies some control management rules, such as intentional load shedding, priority load management, and communication energy saving. These energy saving rules establish a trade-off between increasing microgrid energy availability and communication system reliability. To achieve a compromised solution, a continuous time Markov chain model describes the impact of energy saving policies into system reliability. The proposed methodology is simulated and tested with the help of the modified IEEE 34 node test-system.

Reliability of the Dutch-language version of the Communication Function Classification System and its association with language comprehension and method of communication.

Science.gov (United States)

Vander Zwart, Karlijn E; Geytenbeek, Joke J; de Kleijn, Maaike; Oostrom, Kim J; Gorter, Jan Willem; Hidecker, Mary Jo Cooley; Vermeulen, R Jeroen

2016-02-01

The aims of this study were to determine the intra- and interrater reliability of the Dutch-language version of the Communication Function Classification System (CFCS-NL) and to investigate the association between the CFCS level and (1) spoken language comprehension and (2) preferred method of communication in children with cerebral palsy (CP). Participants were 93 children with CP (50 males, 43 females; mean age 7y, SD 2y 6mo, range 2y 9mo-12y 10mo; unilateral spastic [n=22], bilateral spastic [n=51], dyskinetic [n=15], ataxic [n=3], not specified [n=2]; Gross Motor Function Classification System level I [n=16], II [n=14], III, [n=7], IV [n=24], V [n=31], unknown [n=1]), recruited from rehabilitation centres throughout the Netherlands. Because some centres only contributed to part of the study, different numbers of participants are presented for different aspects of the study. Parents and speech and language therapists (SLTs) classified the communication level using the CFCS. Kappa was used to determine the intra- and interrater reliability. Spearman's correlation coefficient was used to determine the association between CFCS level and spoken language comprehension, and Fisher's exact test was used to examine the association between the CFCS level and method of communication. Interrater reliability of the CFCS-NL between parents and SLTs was fair (r=0.54), between SLTs good (r=0.78), and the intrarater (SLT) reliability very good (r=0.85). The association between the CFCS and spoken language comprehension was strong for SLTs (r=0.63) and moderate for parents (r=0.51). There was a statistically significant difference between the CFCS level and the preferred method of communication of the child (pcommunication in children with CP. Preferably, professionals should classify the child's CFCS level in collaboration with the parents to acquire the most comprehensive information about the everyday communication of the child in various situations both with familiar and

Reliability and fatigue characteristics of a standing hip isometric endurance protocol.

Science.gov (United States)

Mutchler, Jessica A; Weinhandl, Joshua T; Hoch, Matthew C; Van Lunen, Bonnie L

2015-08-01

Muscle fatigue is a common consideration when evaluating and rehabilitating athletic injuries. The presence of muscular fatigue has been previously determined by quantifying median frequency (MF) through a power spectral analysis on EMG signals collected throughout an endurance task. Research has not yet determined if a prolonged isometric test in a standing position generates muscular fatigue of the hip. The purpose of this study was to determine the reliability and fatigue characteristics of a standing hip isometric endurance test. Twenty healthy participants completed one 60-s Maximum Voluntary Isometric Contraction of standing hip flexion, extension, adduction, and abduction. MF of the participants' dominant limb rectus femoris (RF), biceps femoris (BF), gluteus maximus (GMax), gluteus medius (GMed) and adductor longus (ADD) was determined via surface electromyography during two sessions, 30-min apart. Reliability values (ICC2,1) were moderate-to-excellent for all time intervals of each action (FlexionRF: >0.80; ExtensionBF: >0.89; ExtensionGMax: >0.60; AdductionADD: >0.78; AbductionGMed: >0.60) and MF significantly decreased over time for all actions. Results suggest the endurance test is a reliable technique to generate muscular fatigue for hip flexion, extension, adduction and abduction. It can be used as a time efficient fatigue protocol specific to the RF, BF, GMax, ADD and GMed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Protocol: validation of the INCODE barometer to measure the innovation compe-tence through the Rasch Measurement Theory

Directory of Open Access Journals (Sweden)

Lidia Sanchez

2017-06-01

Full Text Available This communication presents a protocol in order to show the different phases that must be followed in order to validate the INCODE barometer, which is used to measure the innovation competence, with Rasch Measurement Theory. Five phases are stated: dimensionality analysis, individual reliability and validity analysis of ítems and persons, global reliability and validity analysis, and cathegory analysis.

Security analysis of the “Ping–Pong” quantum communication protocol in the presence of collective-rotation noise

International Nuclear Information System (INIS)

Li, Jian; Li, Lingyun; Jin, Haifei; Li, Ruifan

2013-01-01

Environmental noise is inevitable in non-isolated systems. It is, therefore, necessary to analyze the security of the “Ping–Pong” protocol in a noisy environment. An excellent model for collective-rotation noise is introduced, and information theoretical methods are applied to analyze the security of this protocol. If noise level ε is lower than 11%, an eavesdropper can gain some, but not all, information freely without being detected. Otherwise, the protocol becomes insecure. We conclude that the use of ‘Ping–Pong’ protocol as a quantum secure direct communication (QSDC) protocol is quasi-secure, as declared by the original author when ε⩽11%.

Security analysis of the “Ping–Pong” quantum communication protocol in the presence of collective-rotation noise

Energy Technology Data Exchange (ETDEWEB)

Li, Jian; Li, Lingyun, E-mail: lilingyun@bupt.edu.cn; Jin, Haifei; Li, Ruifan

2013-11-22

Environmental noise is inevitable in non-isolated systems. It is, therefore, necessary to analyze the security of the “Ping–Pong” protocol in a noisy environment. An excellent model for collective-rotation noise is introduced, and information theoretical methods are applied to analyze the security of this protocol. If noise level ε is lower than 11%, an eavesdropper can gain some, but not all, information freely without being detected. Otherwise, the protocol becomes insecure. We conclude that the use of ‘Ping–Pong’ protocol as a quantum secure direct communication (QSDC) protocol is quasi-secure, as declared by the original author when ε⩽11%.

Interactive real-time media streaming with reliable communication

Science.gov (United States)

Pan, Xunyu; Free, Kevin M.

2014-02-01

Streaming media is a recent technique for delivering multimedia information from a source provider to an end- user over the Internet. The major advantage of this technique is that the media player can start playing a multimedia file even before the entire file is transmitted. Most streaming media applications are currently implemented based on the client-server architecture, where a server system hosts the media file and a client system connects to this server system to download the file. Although the client-server architecture is successful in many situations, it may not be ideal to rely on such a system to provide the streaming service as users may be required to register an account using personal information in order to use the service. This is troublesome if a user wishes to watch a movie simultaneously while interacting with a friend in another part of the world over the Internet. In this paper, we describe a new real-time media streaming application implemented on a peer-to-peer (P2P) architecture in order to overcome these challenges within a mobile environment. When using the peer-to-peer architecture, streaming media is shared directly between end-users, called peers, with minimal or no reliance on a dedicated server. Based on the proposed software pɛvμa (pronounced [revma]), named for the Greek word meaning stream, we can host a media file on any computer and directly stream it to a connected partner. To accomplish this, pɛvμa utilizes the Microsoft .NET Framework and Windows Presentation Framework, which are widely available on various types of windows-compatible personal computers and mobile devices. With specially designed multi-threaded algorithms, the application can stream HD video at speeds upwards of 20 Mbps using the User Datagram Protocol (UDP). Streaming and playback are handled using synchronized threads that communicate with one another once a connection is established. Alteration of playback, such as pausing playback or tracking to a

A statistical frame based TDMA protocol for human body communication.

Science.gov (United States)

Nie, Zedong; Li, Zhao; Huang, Renwei; Liu, Yuhang; Li, Jingzhen; Wang, Lei

2015-07-09

Human body communication (HBC) using the human body as the transmission medium, which has been regarded as one of the most promising short-range communications in wireless body area networks (WBAN). Compared to the traditional wireless networks, two challenges are existed in HBC based WBAN. (1) Its sensor nodes should be energy saving since it is inconvenient to replace or recharge the battery on these sensor nodes; (2) the coordinator should be able to react dynamically and rapidly to the burst traffic triggered by sensing events. Those burst traffic conditions include vital physical signal (electrocardiogram, electroencephalogram etc.) monitoring, human motion detection (fall detection, activity monitoring, gesture recognition, motion sensing etc.) and so on. To cope with aforementioned challenges, a statistical frame based TDMA (S-TDMA) protocol with multi-constrained (energy, delay, transmission efficiency and emergency management) service is proposed in this paper. The scenarios where burst traffic is often triggered rapidly with low power consumption and low delay is handled in our proposed S-TDMA. A beacon frame with the contained synchronous and poll information is designed to reduce the possibility of collisions of request frames. A statistical frame which broadcasts the unified scheduling information is adopted to avoid packet collisions, idle listening and overhearing. Dynamic time slot allocation mechanism is presented to manage the burst traffic and reduce the active period in each beacon period. An emergency mechanism is proposed for vital signals to be transmitted. The theory analysis is proceed and the result is evaluated in the hardware platform. To verify its feasibility, S-TDMA was fully implemented on our independently-developed HBC platform where four sensor nodes and a coordinator are fastened on a human body. Experiment results show that S-TDMA costs 89.397 mJ every 20 s when the payload size is 122 bytes, 9.51% lower than Lightweight MAC

Training conversation partners of persons with communication disorders related to Parkinson's disease--a protocol and a pilot study.

Science.gov (United States)

Forsgren, Emma; Antonsson, Malin; Saldert, Charlotta

2013-07-01

This paper reports on the adaptation of a training programme for conversation partners of persons with Parkinson's disease, and a protocol for assessment of possible changes in conversational interaction as a result of intervention. We present data from an explorative multiple case study with three individuals with Parkinson's disease and their spouses. Repeated analysis of natural conversational interaction and measures of the participants' perception of communication as well as measures of different cognitive abilities were obtained. The results show that the communication in all three dyads was affected by both speech and language problems and that the conversation training model and the assessment protocol may work well after minor adjustments. Influence of different aspects of cognition on communication is discussed.

Energy efficient routing protocols for wireless sensor networks: comparison and future directions

Directory of Open Access Journals (Sweden)

Loganathan Murukesan

2017-01-01

Full Text Available Wireless sensor network consists of nodes with limited resources. Hence, it is important to design protocols or algorithms which increases energy efficiency in order to improve the network lifetime. In this paper, techniques used in the network layer (routing of the internet protocol stack to achieve energy efficiency are reviewed. Usually, the routing protocols are classified into four main schemes: (1 Network Structure, (2 Communication Model, (3 Topology Based, and (4 Reliable Routing. In this work, only network structure based routing protocols are reviewed due to the page constraint. Besides, this type of protocols are much popular among the researchers since they are fairly simple to implement and produce good results as presented in this paper. Also, the pros and cons of each protocols are presented. Finally, the paper concludes with possible further research directions.

An Improved Protocol for Controlled Deterministic Secure Quantum Communication Using Five-Qubit Entangled State

Science.gov (United States)

Kao, Shih-Hung; Lin, Jason; Tsai, Chia-Wei; Hwang, Tzonelih

2018-03-01

In early 2009, Xiu et al. (Opt. Commun. 282(2) 333-337 2009) presented a controlled deterministic secure quantum communication (CDSQC) protocol via a newly constructed five-qubit entangled quantum state. Later, Qin et al. (Opt. Commun. 282(13), 2656-2658 2009) pointed out two security loopholes in Xiu et al.'s protocol: (1) A correlation-elicitation (CE) attack can reveal the entire secret message; (2) A leakage of partial information for the receiver is noticed. Then, Xiu et al. (Opt. Commun. 283(2), 344-347 2010) presented a revised CDSQC protocol to remedy the CE attack problem. However, the information leakage problem still remains open. This work proposes a new CDSQC protocol using the same five-qubit entangled state which can work without the above mentioned security problems. Moreover, the Trojan Horse attacks can be automatically avoided without using detecting devices in the new CDSQC.

An Improved Protocol for Controlled Deterministic Secure Quantum Communication Using Five-Qubit Entangled State

Science.gov (United States)

Kao, Shih-Hung; Lin, Jason; Tsai, Chia-Wei; Hwang, Tzonelih

2018-06-01

In early 2009, Xiu et al. (Opt. Commun. 282(2) 333-337 2009) presented a controlled deterministic secure quantum communication (CDSQC) protocol via a newly constructed five-qubit entangled quantum state. Later, Qin et al. (Opt. Commun. 282(13), 2656-2658 2009) pointed out two security loopholes in Xiu et al.'s protocol: (1) A correlation-elicitation (CE) attack can reveal the entire secret message; (2) A leakage of partial information for the receiver is noticed. Then, Xiu et al. (Opt. Commun. 283(2), 344-347 2010) presented a revised CDSQC protocol to remedy the CE attack problem. However, the information leakage problem still remains open. This work proposes a new CDSQC protocol using the same five-qubit entangled state which can work without the above mentioned security problems. Moreover, the Trojan Horse attacks can be automatically avoided without using detecting devices in the new CDSQC.

Simple algorithm for improved security in the FDDI protocol

Science.gov (United States)

Lundy, G. M.; Jones, Benjamin

1993-02-01

We propose a modification to the Fiber Distributed Data Interface (FDDI) protocol based on a simple algorithm which will improve confidential communication capability. This proposed modification provides a simple and reliable system which exploits some of the inherent security properties in a fiber optic ring network. This method differs from conventional methods in that end to end encryption can be facilitated at the media access control sublayer of the data link layer in the OSI network model. Our method is based on a variation of the bit stream cipher method. The transmitting station takes the intended confidential message and uses a simple modulo two addition operation against an initialization vector. The encrypted message is virtually unbreakable without the initialization vector. None of the stations on the ring will have access to both the encrypted message and the initialization vector except the transmitting and receiving stations. The generation of the initialization vector is unique for each confidential transmission and thus provides a unique approach to the key distribution problem. The FDDI protocol is of particular interest to the military in terms of LAN/MAN implementations. Both the Army and the Navy are considering the standard as the basis for future network systems. A simple and reliable security mechanism with the potential to support realtime communications is a necessary consideration in the implementation of these systems. The proposed method offers several advantages over traditional methods in terms of speed, reliability, and standardization.

A Study on IP Network Recovery through Routing Protocols

Directory of Open Access Journals (Sweden)

K. Karthik

2016-09-01

Full Text Available Internet has taken major role in our communication infrastructure. Such that requirement of internet availability and reliability has increasing accordingly. The major network failure reasons are failure of node and failure of link among the nodes. This can reduce the performance of major applications in an IP networks. The network recovery should be fast enough so that service interruption of link or node failure. The new path taken by the diverted traffic can be computed either at the time of failures or before failures. These mechanisms are known as Reactive and Proactive protocols respectively. In this paper, we surveyed reactive and proactive protocols mechanisms for IP network recovery.

Inter-observer reliability of animal-based welfare indicators included in the Animal Welfare Indicators welfare assessment protocol for dairy goats.

Science.gov (United States)

Vieira, A; Battini, M; Can, E; Mattiello, S; Stilwell, G

2018-01-08

This study was conducted within the context of the Animal Welfare Indicators (AWIN) project and the underlying scientific motivation for the development of the study was the scarcity of data regarding inter-observer reliability (IOR) of welfare indicators, particularly given the importance of reliability as a further step for developing on-farm welfare assessment protocols. The objective of this study is therefore to evaluate IOR of animal-based indicators (at group and individual-level) of the AWIN welfare assessment protocol (prototype) for dairy goats. In the design of the study, two pairs of observers, one in Portugal and another in Italy, visited 10 farms each and applied the AWIN prototype protocol. Farms in both countries were visited between January and March 2014, and all the observers received the same training before the farm visits were initiated. Data collected during farm visits, and analysed in this study, include group-level and individual-level observations. The results of our study allow us to conclude that most of the group-level indicators presented the highest IOR level ('substantial', 0.85 to 0.99) in both field studies, pointing to a usable set of animal-based welfare indicators that were therefore included in the first level of the final AWIN welfare assessment protocol for dairy goats. Inter-observer reliability of individual-level indicators was lower, but the majority of them still reached 'fair to good' (0.41 to 0.75) and 'excellent' (0.76 to 1) levels. In the paper we explore reasons for the differences found in IOR between the group and individual-level indicators, including how the number of individual-level indicators to be assessed on each animal and the restraining method may have affected the results. Furthermore, we discuss the differences found in the IOR of individual-level indicators in both countries: the Portuguese pair of observers reached a higher level of IOR, when compared with the Italian observers. We argue how the

Automobile inspection system based on wireless communication

Science.gov (United States)

Miao, Changyun; Ye, Chunqing

2010-07-01

This paper aims to research the Automobile Inspection System based on Wireless Communication, and suggests an overall design scheme which uses GPS for speed detection and Bluetooth and GPRS for communication. The communication between PDA and PC was realized by means of GPRS and TCP/IP; and the hardware circuit and software for detection terminal were devised by means of JINOU-3264 Bluetooth Module after analyzing the Bluetooth and its communication protocol. According to the results of debugging test, this system accomplished GPRS based data communication and management as well as the real-time detection on auto safety performance parameters in crash test via PC, whereby the need for mobility and reliability was met and the efficiency and level of detection was improved.

Specification and Design of a Fault Recovery Model for the Reliable Multicast Protocol

Science.gov (United States)

Montgomery, Todd; Callahan, John R.; Whetten, Brian

1996-01-01

The Reliable Multicast Protocol (RMP) provides a unique, group-based model for distributed programs that need to handle reconfiguration events at the application layer. This model, called membership views, provides an abstraction in which events such as site failures, network partitions, and normal join-leave events are viewed as group reformations. RMP provides access to this model through an application programming interface (API) that notifies an application when a group is reformed as the result of a some event. RMP provides applications with reliable delivery of messages using an underlying IP Multicast media to other group members in a distributed environment even in the case of reformations. A distributed application can use various Quality of Service (QoS) levels provided by RMP to tolerate group reformations. This paper explores the implementation details of the mechanisms in RMP that provide distributed applications with membership view information and fault recovery capabilities.

Data communications

International Nuclear Information System (INIS)

Preckshot, G.G.

1993-08-01

The purpose of this paper is to recommend regulatory guidance for reviewers examining computer communication systems used in nuclear power plants. The recommendations cover three areas important to these communications systems: system design, communication protocols, and communication media. The first area, system design, considers three aspects of system design--questions about architecture, specific risky design elements or omissions to look for in designs being reviewed, and recommendations for multiplexed data communication systems used in safety systems. The second area reviews pertinent aspects of communication protocol design and makes recommendations for newly designed protocols or the selection of existing protocols for safety system, information display, and non-safety control system use. The third area covers communication media selection, which differs significantly from traditional wire and cable. The recommendations for communication media extend or enhance the concerns of published IEEE standards about three subjects: data rate, imported hazards and maintainability

Study, design and realization of a fault-tolerant and predictable synchronous communication protocol on off-the-shelf components; Etude, conception et mise en oeuvre d'un protocole de communication synchrone tolerant aux fautes et predictible sur des composants reseaux standards

Energy Technology Data Exchange (ETDEWEB)

Chabrol, D

2006-06-15

This PhD thesis contributes to the design and realization of safety-critical real-time systems on multiprocessor architectures with distributed memory. They are essential to compute systems that have to ensure complex and critical functions. This PhD thesis deals with communication media management. The communication management conditions strongly the capability of the system to fulfill the timeliness property and the dependability requirements. Our contribution includes: - The design of predictable and fault-tolerant synchronous communication protocol; - The study and the definition of the execution model to have a efficient and safe communications management; - The proposal of a method to generate automatically the communications scheduling. Our approach is based on a communication model that allows the analysis of the feasibility, before execution, of a distributed safe-critical real-time system with timeliness and safety requirements. This leads to the definition of an execution model based on a time-triggered and parallel communication management. A set of linear constraints system is generated automatically to compute the network scheduling and the network load with timeliness fulfillment. Then, the proposed communication interface is based on an advanced version of TDMA protocol which allows to use proprietary components (TTP, FlexRay) as well as standard components (Ethernet). The concepts presented in this thesis lead to the realisation and evaluation of a prototype within the framework of the OASIS project done at the CEA/List. (author)

A Robust and Self-Paced BCI System Based on a Four Class SSVEP Paradigm: Algorithms and Protocols for a High-Transfer-Rate Direct Brain Communication

Directory of Open Access Journals (Sweden)

Sergio Parini

2009-01-01

Full Text Available In this paper, we present, with particular focus on the adopted processing and identification chain and protocol-related solutions, a whole self-paced brain-computer interface system based on a 4-class steady-state visual evoked potentials (SSVEPs paradigm. The proposed system incorporates an automated spatial filtering technique centred on the common spatial patterns (CSPs method, an autoscaled and effective signal features extraction which is used for providing an unsupervised biofeedback, and a robust self-paced classifier based on the discriminant analysis theory. The adopted operating protocol is structured in a screening, training, and testing phase aimed at collecting user-specific information regarding best stimulation frequencies, optimal sources identification, and overall system processing chain calibration in only a few minutes. The system, validated on 11 healthy/pathologic subjects, has proven to be reliable in terms of achievable communication speed (up to 70 bit/min and very robust to false positive identifications.

76 FR 23812 - Reliability and Continuity of Communications Networks, Including Broadband Technologies; Effects...

Science.gov (United States)

2011-04-28

...-418-7452 or [email protected] ; or Jeffery Goldthorp, Associate Chief for Cybersecurity and....gov ; or Lauren Kravetz, Deputy Chief, Cybersecurity and Communications Reliability Division, Public... for inspection and copying during normal business hours in the FCC Reference Information Center...

A hybrid MAC protocol design for energy-efficient very-high-throughput millimeter wave, wireless sensor communication networks

Science.gov (United States)

Jian, Wei; Estevez, Claudio; Chowdhury, Arshad; Jia, Zhensheng; Wang, Jianxin; Yu, Jianguo; Chang, Gee-Kung

2010-12-01

This paper presents an energy-efficient Medium Access Control (MAC) protocol for very-high-throughput millimeter-wave (mm-wave) wireless sensor communication networks (VHT-MSCNs) based on hybrid multiple access techniques of frequency division multiplexing access (FDMA) and time division multiplexing access (TDMA). An energy-efficient Superframe for wireless sensor communication network employing directional mm-wave wireless access technologies is proposed for systems that require very high throughput, such as high definition video signals, for sensing, processing, transmitting, and actuating functions. Energy consumption modeling for each network element and comparisons among various multi-access technologies in term of power and MAC layer operations are investigated for evaluating the energy-efficient improvement of proposed MAC protocol.

Quantifying the nonlocality of Greenberger-Horne-Zeilinger quantum correlations by a bounded communication simulation protocol.

Science.gov (United States)

Branciard, Cyril; Gisin, Nicolas

2011-07-08

The simulation of quantum correlations with finite nonlocal resources, such as classical communication, gives a natural way to quantify their nonlocality. While multipartite nonlocal correlations appear to be useful resources, very little is known on how to simulate multipartite quantum correlations. We present a protocol that reproduces tripartite Greenberger-Horne-Zeilinger correlations with bounded communication: 3 bits in total turn out to be sufficient to simulate all equatorial Von Neumann measurements on the tripartite Greenberger-Horne-Zeilinger state.

Study, design and realization of a fault-tolerant and predictable synchronous communication protocol on off-the-shelf components

International Nuclear Information System (INIS)

Chabrol, D.

2006-06-01

This PhD thesis contributes to the design and realization of safety-critical real-time systems on multiprocessor architectures with distributed memory. They are essential to compute systems that have to ensure complex and critical functions. This PhD thesis deals with communication media management. The communication management conditions strongly the capability of the system to fulfill the timeliness property and the dependability requirements. Our contribution includes: - The design of predictable and fault-tolerant synchronous communication protocol; - The study and the definition of the execution model to have a efficient and safe communications management; - The proposal of a method to generate automatically the communications scheduling. Our approach is based on a communication model that allows the analysis of the feasibility, before execution, of a distributed safe-critical real-time system with timeliness and safety requirements. This leads to the definition of an execution model based on a time-triggered and parallel communication management. A set of linear constraints system is generated automatically to compute the network scheduling and the network load with timeliness fulfillment. Then, the proposed communication interface is based on an advanced version of TDMA protocol which allows to use proprietary components (TTP, FlexRay) as well as standard components (Ethernet). The concepts presented in this thesis lead to the realisation and evaluation of a prototype within the framework of the OASIS project done at the CEA/List. (author)

FPGA communications based on Gigabit Ethernet

International Nuclear Information System (INIS)

Doolittle, L.R.; Serrano, C.

2012-01-01

The use of Field Programmable Gate Arrays (FPGAs) in accelerators is widespread due to their flexibility, performance, and reasonable costs. Whether they are used for fast feedback systems, data acquisition, fast communications using custom protocols, or any other application, there is a need for the end-user and the global control software to access FPGA features using a commodity computer. The choice of communication standards that can be used to interface to a FPGA board is wide, however there is one that stands out for its maturity, basis in standards, performance, and hardware support: Gigabit Ethernet. In the context of accelerators it is desirable to have highly reliable, portable, and flexible solutions. We have therefore developed a chip and board-independent FPGA design which implements the Gigabit Ethernet (GbE) standard. Our design has been configured for use with multiple projects, supports full line-rate traffic, and communicates with any other device implementing the same well-established protocol, easily supported by any modern workstation or controls computer. (authors)

Quantum cryptography communication technology

Energy Technology Data Exchange (ETDEWEB)

Cho, Jai Wan; Choi, Young Soo; Lee, Jae Chul; Choi, Yu Rak; Jung, Gwang Il; Jung, Jong Eun; Hong, Seok Boong; Koo, In Soo

2007-09-15

Quantum cryptography communication based on quantum mechanics provides and unconditional security between two users. Even though huge advance has been done since the 1984, having a complete system is still far away. In the case of real quantum cryptography communication systems, an unconditional security level is lowered by the imperfection of the communication unit. It is important to investigate the unconditional security of quantum communication protocols based on these experimental results and implementation examples for the advanced spread all over the world. The Japanese report, titled, 'Investigation report on the worldwide trends of quantum cryptography communications systems' was translated and summarized in this report. An unconditional security theory of the quantum cryptography and real implementation examples in the domestic area are investigated also. The goal of the report is to make quantum cryptography communication more useful and reliable alternative telecommunication infrastructure as the one of the cyber security program of the class 1-E communication system of nuclear power plant. Also another goal of this report is to provide the quantitative decision basis on the quantum cryptography communication when this secure communication system will be used in class 1-E communication channel of the nuclear power plant.

Quantum cryptography communication technology

International Nuclear Information System (INIS)

Cho, Jai Wan; Choi, Young Soo; Lee, Jae Chul; Choi, Yu Rak; Jung, Gwang Il; Jung, Jong Eun; Hong, Seok Boong; Koo, In Soo

2007-09-01

Quantum cryptography communication based on quantum mechanics provides and unconditional security between two users. Even though huge advance has been done since the 1984, having a complete system is still far away. In the case of real quantum cryptography communication systems, an unconditional security level is lowered by the imperfection of the communication unit. It is important to investigate the unconditional security of quantum communication protocols based on these experimental results and implementation examples for the advanced spread all over the world. The Japanese report, titled, 'Investigation report on the worldwide trends of quantum cryptography communications systems' was translated and summarized in this report. An unconditional security theory of the quantum cryptography and real implementation examples in the domestic area are investigated also. The goal of the report is to make quantum cryptography communication more useful and reliable alternative telecommunication infrastructure as the one of the cyber security program of the class 1-E communication system of nuclear power plant. Also another goal of this report is to provide the quantitative decision basis on the quantum cryptography communication when this secure communication system will be used in class 1-E communication channel of the nuclear power plant

Remote control of the industry processes. POWERLINK protocol application

Science.gov (United States)

Wóbel, A.; Paruzel, D.; Paszkiewicz, B.

2017-08-01

The present technological development enables the use of solutions characterized by a lower failure rate, and work with greater precision. This allows you to obtain the most efficient production, high speed production and reliability of individual components. The main scope of this article was POWERLINK protocol application for communication with the controller B & R through communication Ethernet for recording process parameters. This enables control of run production cycle using an internal network connected to the PC industry. Knowledge of the most important parameters of the production in real time allows detecting of a failure immediately after occurrence. For this purpose, the position of diagnostic use driver X20CP1301 B&R to record measurement data such as pressure, temperature valve between the parties and the torque required to change the valve setting was made. The use of POWERLINK protocol allows for the transmission of information on the status of every 200 μs.

L2-LBMT: A Layered Load Balance Routing Protocol for underwater multimedia data transmission

Science.gov (United States)

Lv, Ze; Tang, Ruichun; Tao, Ye; Sun, Xin; Xu, Xiaowei

2017-12-01

Providing highly efficient underwater transmission of mass multimedia data is challenging due to the particularities of the underwater environment. Although there are many schemes proposed to optimize the underwater acoustic network communication protocols, from physical layer, data link layer, network layer to transport layer, the existing routing protocols for underwater wireless sensor network (UWSN) still cannot well deal with the problems in transmitting multimedia data because of the difficulties involved in high energy consumption, low transmission reliability or high transmission delay. It prevents us from applying underwater multimedia data to real-time monitoring of marine environment in practical application, especially in emergency search, rescue operation and military field. Therefore, the inefficient transmission of marine multimedia data has become a serious problem that needs to be solved urgently. In this paper, A Layered Load Balance Routing Protocol (L2-LBMT) is proposed for underwater multimedia data transmission. In L2-LBMT, we use layered and load-balance Ad Hoc Network to transmit data, and adopt segmented data reliable transfer (SDRT) protocol to improve the data transport reliability. And a 3-node variant of tornado (3-VT) code is also combined with the Ad Hoc Network to transmit little emergency data more quickly. The simulation results show that the proposed protocol can balance energy consumption of each node, effectively prolong the network lifetime and reduce transmission delay of marine multimedia data.

Improvement The Transmission Efficiency For Wireless Packet Communication Systems Using Automatic Control for power And Time Slot Width Of Slotted Non persistent ISMA Protocol

Directory of Open Access Journals (Sweden)

Saad M. Hardan

2013-05-01

Full Text Available In packed communication systems which use a protocol, the protocol should perform the allocation of channels such that the transmission channel is used efficiently. Efficiency is usually measured in terms of channel throughput and the average transmission  delay. The Slotted Nonpersistent ISMA protocol is one of random access protocols used in packed communication systems. In this research a Slotted Nonpersistent ISMA protocol Model with automatic control for power and time slot is proposed. the suggested algorithm enable the base station(access point to control  the protocol time slot length and  transmission power in a dynamic way to control the normalized propagation delay d and to maintain all the uplink signals in the limit of captured power threshold (capture ratio in order to control the  throughput and the average transmission delay of the communication system by an automatic method. the computer simulation results  confirm the activity of the  proposed algorithm for increasing the  throughput and decreasing the average transmission delay by an accepted ratios.

Inter-rater and intra-rater reliability of a clinical protocol for measuring turnout in collegiate dancers.

Science.gov (United States)

Greene, Amanda; Lasner, Andrea; Deu, Rajwinder; Oliphant, Seth; Johnson, Kenneth

2018-02-02

Reliable methods of measuring turnout in dancers and comparing active turnout (used in class) with functional (uncompensated) turnout are needed. Authors have suggested measurement techniques but there is no clinically useful, easily reproducible technique with established inter-rater and intra-rater reliability. We adapted a technique based on previous research, which is easily reproducible. We hypothesized excellent inter-rater and intra-rater reliability between experienced physical therapists (PTs) and a briefly trained faculty member from a university's department of dance. Thirty-two participants were recruited from the same dance department. Dancers' active and functional turnout was measured by each rater. We found that our technique for measuring active and functional turnout has excellent inter-rater and intra-rater reliability when performed by two experienced PTs and by one briefly trained university-level dance faculty member. For active turnout, inter-rater reliability was 0.78 among all raters and 0.82 among only the PT raters; intra-rater reliability was 0.82 among all raters and 0.85 among only the PT raters. For functional turnout, inter-rater reliability was 0.86 among all raters and 0.88 among only the PT raters; intra-rater reliability was 0.87 among all raters and 0.88 among only the PT raters. The measurement technique described provides a standardized protocol with excellent inter-rater and intra-rater reliability when performed by experienced PTs or by a briefly trained university-level dance faculty member.

Satellite communication transponders and their reliability; Eisei tosai tsushin kiki oyobi shinraisei ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Ogawa, H [NTT Wireless System Laboratories, Kanagawa (Japan)

1994-11-01

The Engineering Test Satellite-VI is a large composite test satellite weighing two tons to perform different communication experiments. Adoption of the multi-beam satellite communication system has made possible to increase the transmission capacity, reduce the sizes of earth stations, and utilize frequencies more effectively. This paper describes the configuration of the relaying devices mounted thereon, the newly developed circuit technologies, and their reliability. The multi-beam satellite communication system mounts a number of transponders, with the frequency bands used divided into the 2.6/2.5 GHz band between the moving body and the satellite, the 6/4 GHz band for the channels between the earth stations and the satellite, and the 30/20 GHz band for the fixed communications. These arrangements were intended to achieve large size reduction as a result of applying the integrated circuit technology. The transmitters and the receivers corresponding to each beam are connected by using the satellite switches (16 inputs {times} 12 outputs). The parts used were general purpose ones rather than those specified in the MIL standards because of their number having reached so huge. Their reliability was ensured by long-term burn-in operations. 5 refs., 6 figs., 1 tab.

Satellite communication on pipeline supervision using TCP-IP Protocol; Comunicacao via satelite na supervisao de dutos usando o protocolo TCP-IP

Energy Technology Data Exchange (ETDEWEB)

Silva, Agliberto Pessoa da [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Brunette, Sergio Henrique de Moraes

2003-07-01

Bit transparent type or X-25 protocols have been used in VSAT satellite communication by PETROBRAS pipeline Supervisory Control and Data Acquisition System (SCADA) as access protocol. Both solutions have inconveniences. By the first one, difficulties exist for analysis and diagnosis of connection flaws, and therefore, for a ready identification by the system management stations of abnormality location. On the other hand, the usage of the X-25 brings an additional over-head in the communication since this is not an available option in most of the equipment that compose the SCADA. The access to VSAT through Ethernet, in the opposite, makes available all networks management tools of the TCP/IP platform and it allows a direct connection to the field devices, since the main models of the several makers of Programmable Controllers and Remote Terminal Units have Ethernet port. An additional earnings is the possibility of standardization that this solution allows. This paper describes a series of communication tests between two Programmable Controllers communicating through the satellite, using a protocol over Ethernet/TCP/IP. (author)

A quantum secure direct communication protocol based on a five-particle cluster state and classical XOR operation

International Nuclear Information System (INIS)

Li Jian; Song Danjie; Guo Xiaojing; Jing Bo

2012-01-01

In order to transmit secure messages, a quantum secure direct communication protocol based on a five-particle cluster state and classical XOR operation is presented. The five-particle cluster state is used to detect eavesdroppers, and the classical XOR operation serving as a one-time-pad is used to ensure the security of the protocol. In the security analysis, the entropy theory method is introduced, and three detection strategies are compared quantitatively by using the constraint between the information that the eavesdroppers can obtain and the interference introduced. If the eavesdroppers intend to obtain all the information, the detection rate of the original ping-pong protocol is 50%; the second protocol, using two particles of the Einstein-Podolsky-Rosen pair as detection particles, is also 50%; while the presented protocol is 89%. Finally, the security of the proposed protocol is discussed, and the analysis results indicate that the protocol in this paper is more secure than the other two. (authors)

Assessing communication skills in dietetic consultations: the development of the reliable and valid DIET-COMMS tool.

Science.gov (United States)

Whitehead, K A; Langley-Evans, S C; Tischler, V A; Swift, J A

2014-04-01

There is an increasing emphasis on the development of communication skills for dietitians but few evidence-based assessment tools available. The present study aimed to develop a dietetic-specific, short, reliable and valid assessment tool for measuring communication skills in patient consultations: DIET-COMMS. A literature review and feedback from 15 qualified dietitians were used to establish face and content validity during the development of DIET-COMMS. In total, 113 dietetic students and qualified dietitians were video-recorded undertaking mock consultations, assessed using DIET-COMMS by the lead author, and used to establish intra-rater reliability, as well as construct and predictive validity. Twenty recorded consultations were reassessed by nine qualified dietitians to assess inter-rater reliability: eight of these assessors were interviewed to determine user evaluation. Significant improvements in DIET-COMMS scores were achieved as students and qualified staff progressed through their training and gained experience, demonstrating construct validity, and also by qualified staff attending a training course, indicating predictive validity (P skills in practice was questioned. DIET-COMMS is a short, user-friendly, reliable and valid tool for measuring communication skills in patient consultations with both pre- and post-registration dietitians. Additional work is required to develop a training package for assessors and to identify how DIET-COMMS assessment can acceptably be incorporated into practice. © 2013 The British Dietetic Association Ltd.

Determining Reliability of a Dual-Task Functional Mobility Protocol for Individuals With Lower Extremity Amputation.

Science.gov (United States)

Hunter, Susan W; Frengopoulos, Courtney; Holmes, Jeff; Viana, Ricardo; Payne, Michael W

2018-04-01

To determine the relative and absolute reliability of a dual-task functional mobility assessment. Cross-sectional study. Academic rehabilitation hospital. Individuals (N=60) with lower extremity amputation attending an outpatient amputee clinic (mean age, 58.21±12.59y; 18, 80% male) who were stratified into 3 groups: (1) transtibial amputation of vascular etiology (n=20); (2) transtibial amputation of nonvascular etiology (n=20); and (3) transfemoral or bilateral amputation of any etiology (n=20). Not applicable. Time to complete the L Test measured functional mobility under single- and dual-task conditions. The addition of a cognitive task (serial subtractions by 3's) created dual-task conditions. Single-task performance on the cognitive task was also reported. Intraclass correlation coefficients (ICCs) measured relative reliability; SEM and minimal detectable change with a 95% confidence interval (MDC 95 ) measured absolute reliability. Bland-Altman plots measured agreement between assessments. Relative reliability results were excellent for all 3 groups. Values for the dual-task L Test for those with transtibial amputation of vascular etiology (n=20; mean age, 60.36±7.84y; 19, 90% men) were ICC=.98 (95% confidence interval [CI], .94-.99), SEM=1.36 seconds, and MDC 95 =3.76 seconds; for those with transtibial amputation of nonvascular etiology (n=20; mean age, 55.85±14.08y; 17, 85% men), values were ICC=.93 (95% CI, .80-.98), SEM=1.34 seconds, and MDC 95 =3.71 seconds; and for those with transfemoral or bilateral amputation (n=20; mean age, 58.21±14.88y; 13, 65% men), values were ICC=.998 (95% CI, .996-.999), SEM=1.03 seconds, and MDC 95 =2.85 seconds. Bland-Altman plots indicated that assessments did not vary systematically for each group. This dual-task assessment protocol achieved approved levels of relative reliability values for the 3 groups tested. This protocol may be used clinically or in research settings to assess the interaction between cognition

Cyber Security Vulnerability Impact on I and C Reliability

International Nuclear Information System (INIS)

Hadley, Mark D.; McBride, Justin B.

2006-01-01

We present a discussion of the cyber security vulnerability impact on instrument and control reliability. In the discussion we demonstrate the likely vector of attack and vulnerabilities associated with commodity hardware, protocols and communication media. The current fleet of nuclear power plants in the United States utilizes aging analog instrument and control systems which are more frequently suffering from obsolescence and failure. The commodity equipment available now and in the near future incorporates features from information technology systems which compound cyber vulnerabilities

Reliable Reporting for Massive M2M Communications with Periodic Resource Pooling

DEFF Research Database (Denmark)

Madueño, Germán Corrales; Stefanovic, Cedomir; Popovski, Petar

2014-01-01

This letter considers a wireless M2M communication scenario with a massive number of M2M devices. Each device needs to send its reports within a given deadline and with certain reliability, e.g., 99.99%. A pool of resources available to all M2M devices is periodically available for transmission...... to guarantee the desired reliability of the report delivery within the deadline. The fact that the pool of resources is used by a massive number of devices allows to base the dimensioning on the central limit theorem. The results are interpreted in the context of LTE, but they are applicable to any M2M...

Tool Supported Analysis of Web Services Protocols

DEFF Research Database (Denmark)

Marques, Abinoam P.; Ravn, Anders Peter; Srba, Jiri

2011-01-01

We describe an abstract protocol model suitable for modelling of web services and other protocols communicating via unreliable, asynchronous communication channels. The model is supported by a tool chain where the first step translates tables with state/transition protocol descriptions, often used...... e.g. in the design of web services protocols, into an intermediate XML format. We further translate this format into a network of communicating state machines directly suitable for verification in the model checking tool UPPAAL. We introduce two types of communication media abstractions in order...

Defense Science Board Task Force on Military Satellite Communication and Tactical Networking. Executive Summary

Science.gov (United States)

2017-03-01

Interface Processor BCT Brigade Combat Team BFT Blue Force Tracking BLOS Beyond Line-of-Sight C2 Command And Control C2E Communications in...Satellite Communications and Tactical Networking Appendix D-2 GIG Global Information Grid GMR Ground Mobile Radio GPS Global Positioning System...System SIPRNet Secret Internet Protocol Router Network SITREPS Situational Reports SMART -T Secure Mobile Anti-Jam Reliable Tactical Terminal SMC Space

The reliability of a maximal isometric hip strength and simultaneous surface EMG screening protocol in elite, junior rugby league athletes.

Science.gov (United States)

Charlton, Paula C; Mentiplay, Benjamin F; Grimaldi, Alison; Pua, Yong-Hao; Clark, Ross A

2017-02-01

Firstly to describe the reliability of assessing maximal isometric strength of the hip abductor and adductor musculature using a hand held dynamometry (HHD) protocol with simultaneous wireless surface electromyographic (sEMG) evaluation of the gluteus medius (GM) and adductor longus (AL). Secondly, to describe the correlation between isometric strength recorded with the HHD protocol and a laboratory standard isokinetic device. Reliability and correlational study. A sample of 24 elite, male, junior, rugby league athletes, age 16-20 years participated in repeated HHD and isometric Kin-Com (KC) strength testing with simultaneous sEMG assessment, on average (range) 6 (5-7) days apart by a single assessor. Strength tests included; unilateral hip abduction (ABD) and adduction (ADD) and bilateral ADD assessed with squeeze (SQ) tests in 0 and 45° of hip flexion. HHD demonstrated good to excellent inter-session reliability for all outcome measures (ICC (2,1) =0.76-0.91) and good to excellent association with the laboratory reference KC (ICC (2,1) =0.80-0.88). Whilst intra-session, inter-trial reliability of EMG activation and co-activation outcome measures ranged from moderate to excellent (ICC (2,1) =0.70-0.94), inter-session reliability was poor (all ICC (2,1) Isometric strength testing of the hip ABD and ADD musculature using HHD may be measured reliably in elite, junior rugby league athletes. Due to the poor inter-session reliability of sEMG measures, it is not recommended for athlete screening purposes if using the techniques implemented in this study. Copyright © 2016 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Radio Propagation Analysis of Industrial Scenarios within the Context of Ultra-Reliable Communication

DEFF Research Database (Denmark)

Wassie, Dereje Assefa; Rodriguez Larrad, Ignacio; Berardinelli, Gilberto

2018-01-01

One of the 5G use cases, known as ultra-reliable communication (URC), is expected to support very low packet error rate on the order of 10^(−5) with a 1 ms latency. In an industrial scenario, this would make possible replacing wired connections with wireless for controlling critical processes...

A feedback-retransmission based asynchronous frequency hopping MAC protocol for military aeronautical ad hoc networks

Directory of Open Access Journals (Sweden)

Jinhui TANG

2018-05-01

Full Text Available Attacking time-sensitive targets has rigid demands for the timeliness and reliability of information transmission, while typical Media Access Control (MAC designed for this application works well only in very light-load scenarios; as a consequence, the performances of system throughput and channel utilization are degraded. For this problem, a feedback-retransmission based asynchronous FRequency hopping Media Access (FRMA control protocol is proposed. Burst communication, asynchronous Frequency Hopping (FH, channel coding, and feedback retransmission are utilized in FRMA. With the mechanism of asynchronous FH, immediate packet transmission and multi-packet reception can be realized, and thus the timeliness is improved. Furthermore, reliability can be achieved via channel coding and feedback retransmission. With theories of queuing theory, Markov model, packets collision model, and discrete Laplace transformation, the formulas of packet success probability, system throughput, average packet end-to-end delay, and delay distribution are obtained. The approximation accuracy of theoretical derivation is verified by experimental results. Within a light-load network, the proposed FRMA has the ability of millisecond delay and 99% reliability as well as outperforms the non-feedback-retransmission based asynchronous frequency hopping media access control protocol. Keywords: Ad hoc networks, Aeronautical communications, Frequency hopping, Media Access Control (MAC, Time-sensitive

Workplace-based assessment of communication skills: A pilot project addressing feasibility, acceptance and reliability

Science.gov (United States)

Weyers, Simone; Jemi, Iman; Karger, André; Raski, Bianca; Rotthoff, Thomas; Pentzek, Michael; Mortsiefer, Achim

2016-01-01

Background: Imparting communication skills has been given great importance in medical curricula. In addition to standardized assessments, students should communicate with real patients in actual clinical situations during workplace-based assessments and receive structured feedback on their performance. The aim of this project was to pilot a formative testing method for workplace-based assessment. Our investigation centered in particular on whether or not physicians view the method as feasible and how high acceptance is among students. In addition, we assessed the reliability of the method. Method: As part of the project, 16 students held two consultations each with chronically ill patients at the medical practice where they were completing GP training. These consultations were video-recorded. The trained mentoring physician rated the student’s performance and provided feedback immediately following the consultations using the Berlin Global Rating scale (BGR). Two impartial, trained raters also evaluated the videos using BGR. For qualitative and quantitative analysis, information on how physicians and students viewed feasibility and their levels of acceptance was collected in written form in a partially standardized manner. To test for reliability, the test-retest reliability was calculated for both of the overall evaluations given by each rater. The inter-rater reliability was determined for the three evaluations of each individual consultation. Results: The formative assessment method was rated positively by both physicians and students. It is relatively easy to integrate into daily routines. Its significant value lies in the personal, structured and recurring feedback. The two overall scores for each patient consultation given by the two impartial raters correlate moderately. The degree of uniformity among the three raters in respect to the individual consultations is low. Discussion: Within the scope of this pilot project, only a small sample of physicians and

Workplace-based assessment of communication skills: A pilot project addressing feasibility, acceptance and reliability

Directory of Open Access Journals (Sweden)

Weyers, Simone

2016-11-01

Full Text Available Background: Imparting communication skills has been given great importance in medical curricula. In addition to standardized assessments, students should communicate with real patients in actual clinical situations during workplace-based assessments and receive structured feedback on their performance. The aim of this project was to pilot a formative testing method for workplace-based assessment. Our investigation centered in particular on whether or not physicians view the method as feasible and how high acceptance is among students. In addition, we assessed the reliability of the method.Method: As part of the project, 16 students held two consultations each with chronically ill patients at the medical practice where they were completing GP training. These consultations were video-recorded. The trained mentoring physician rated the student’s performance and provided feedback immediately following the consultations using the Berlin Global Rating scale (BGR. Two impartial, trained raters also evaluated the videos using BGR. For qualitative and quantitative analysis, information on how physicians and students viewed feasibility and their levels of acceptance was collected in written form in a partially standardized manner. To test for reliability, the test-retest reliability was calculated for both of the overall evaluations given by each rater. The inter-rater reliability was determined for the three evaluations of each individual consultation.Results: The formative assessment method was rated positively by both physicians and students. It is relatively easy to integrate into daily routines. Its significant value lies in the personal, structured and recurring feedback. The two overall scores for each patient consultation given by the two impartial raters correlate moderately. The degree of uniformity among the three raters in respect to the individual consultations is low.Discussion: Within the scope of this pilot project, only a small sample

Workplace-based assessment of communication skills: A pilot project addressing feasibility, acceptance and reliability.

Science.gov (United States)

Weyers, Simone; Jemi, Iman; Karger, André; Raski, Bianca; Rotthoff, Thomas; Pentzek, Michael; Mortsiefer, Achim

2016-01-01

Background: Imparting communication skills has been given great importance in medical curricula. In addition to standardized assessments, students should communicate with real patients in actual clinical situations during workplace-based assessments and receive structured feedback on their performance. The aim of this project was to pilot a formative testing method for workplace-based assessment. Our investigation centered in particular on whether or not physicians view the method as feasible and how high acceptance is among students. In addition, we assessed the reliability of the method. Method: As part of the project, 16 students held two consultations each with chronically ill patients at the medical practice where they were completing GP training. These consultations were video-recorded. The trained mentoring physician rated the student's performance and provided feedback immediately following the consultations using the Berlin Global Rating scale (BGR). Two impartial, trained raters also evaluated the videos using BGR. For qualitative and quantitative analysis, information on how physicians and students viewed feasibility and their levels of acceptance was collected in written form in a partially standardized manner. To test for reliability, the test-retest reliability was calculated for both of the overall evaluations given by each rater. The inter-rater reliability was determined for the three evaluations of each individual consultation. Results: The formative assessment method was rated positively by both physicians and students. It is relatively easy to integrate into daily routines. Its significant value lies in the personal, structured and recurring feedback. The two overall scores for each patient consultation given by the two impartial raters correlate moderately. The degree of uniformity among the three raters in respect to the individual consultations is low. Discussion: Within the scope of this pilot project, only a small sample of physicians and

Reliable and Efficient Communications in Wireless Sensor Networks

International Nuclear Information System (INIS)

Abdelhakim, M.M.

2014-01-01

Wireless sensor network (WSN) is a key technology for a wide range of military and civilian applications. Limited by the energy resources and processing capabilities of the sensor nodes, reliable and efficient communications in wireless sensor networks are challenging, especially when the sensors are deployed in hostile environments. This research aims to improve the reliability and efficiency of time-critical communications in WSNs, under both benign and hostile environments. We start with wireless sensor network with mobile access points (SENMA), where the mobile access points traverse the network to collect information from individual sensors. Due to its routing simplicity and energy efficiency, SENMA has attracted lots of attention from the research community. Here, we study reliable distributed detection in SENMA under Byzantine attacks, where some authenticated sensors are compromised to report fictitious information. The q-out-of-m rule is considered. It is popular in distributed detection and can achieve a good trade-off between the miss detection probability and the false alarm rate. However, a major limitation with this rule is that the optimal scheme parameters can only be obtained through exhaustive search. By exploiting the linear relationship between the scheme parameters and the network size, we propose simple but effective sub-optimal linear approaches. Then, for better flexibility and scalability, we derive a near-optimal closed-form solution based on the central limit theorem. It is proved that the false alarm rate of the q-out-of-m scheme diminishes exponentially as the network size increases, even if the percentage of malicious nodes remains fixed. This implies that large-scale sensor networks are more reliable under malicious attacks. To further improve the performance under time varying attacks, we propose an effective malicious node detection scheme for adaptive data fusion; the proposed scheme is analyzed using the entropy-based trust model

Software protocol design: Communication and control in a multi-task robot machine for ITER vacuum vessel assembly and maintenance

International Nuclear Information System (INIS)

Li, Ming; Wu, Huapeng; Handroos, Heikki; Yang, Guangyou; Wang, Yongbo

2015-01-01

Highlights: • A high-level protocol is proposed for the data inter-transmission. • The protocol design is task-oriented for the robot control in the software system. • The protocol functions as a role of middleware in the software. • The protocol running stand-alone as an independent process in the software provides greater security. • Providing a reference design protocol for the multi-task robot machine in the industry. - Abstract: A specific communication and control protocol for software design of a multi-task robot machine is proposed. In order to fulfill the requirements on the complicated multi machining functions and the high performance motion control, the software design of robot is divided into two main parts accordingly, which consists of the user-oriented HMI part and robot control-oriented real-time control system. The two parts of software are deployed in the different hardware for the consideration of run-time performance, which forms a client–server-control architecture. Therefore a high-level task-oriented protocol is designed for the data inter-communication between the HMI part and the control system part, in which all the transmitting data related to a machining task is divided into three categories: trajectory-oriented data, task control-oriented data and status monitoring-oriented data. The protocol consists of three sub-protocols accordingly – a trajectory protocol, task control protocol and status protocol – which are deployed over the Ethernet and run as independent processes in both the client and server computers. The protocols are able to manage the vast amounts of data streaming due to the multi machining functions in a more efficient way. Since the protocol is functioning in the software as a role of middleware, and providing the data interface standards for the developing groups of two parts of software, it also permits greater focus of both software parts developers on their own requirements-oriented design. By

Software protocol design: Communication and control in a multi-task robot machine for ITER vacuum vessel assembly and maintenance

Energy Technology Data Exchange (ETDEWEB)

Li, Ming, E-mail: ming.li@lut.fi [Laboratory of Intelligent Machines, Lappeenranta University of Technology (Finland); Wu, Huapeng; Handroos, Heikki [Laboratory of Intelligent Machines, Lappeenranta University of Technology (Finland); Yang, Guangyou [School of Mechanical Engineering, Hubei University of Technology, Wuhan (China); Wang, Yongbo [Laboratory of Intelligent Machines, Lappeenranta University of Technology (Finland)

2015-10-15

Highlights: • A high-level protocol is proposed for the data inter-transmission. • The protocol design is task-oriented for the robot control in the software system. • The protocol functions as a role of middleware in the software. • The protocol running stand-alone as an independent process in the software provides greater security. • Providing a reference design protocol for the multi-task robot machine in the industry. - Abstract: A specific communication and control protocol for software design of a multi-task robot machine is proposed. In order to fulfill the requirements on the complicated multi machining functions and the high performance motion control, the software design of robot is divided into two main parts accordingly, which consists of the user-oriented HMI part and robot control-oriented real-time control system. The two parts of software are deployed in the different hardware for the consideration of run-time performance, which forms a client–server-control architecture. Therefore a high-level task-oriented protocol is designed for the data inter-communication between the HMI part and the control system part, in which all the transmitting data related to a machining task is divided into three categories: trajectory-oriented data, task control-oriented data and status monitoring-oriented data. The protocol consists of three sub-protocols accordingly – a trajectory protocol, task control protocol and status protocol – which are deployed over the Ethernet and run as independent processes in both the client and server computers. The protocols are able to manage the vast amounts of data streaming due to the multi machining functions in a more efficient way. Since the protocol is functioning in the software as a role of middleware, and providing the data interface standards for the developing groups of two parts of software, it also permits greater focus of both software parts developers on their own requirements-oriented design. By

The UMTS-AKA Protocols for Intelligent Transportation Systems

Directory of Open Access Journals (Sweden)

Hwang Min-Shiang

2009-01-01

Full Text Available The integration of communication protocols into transport systems is a much adored research area today. Much of seminal work has been reported on the topic of intelligent transportation systems (ITS in the recent years. Many advanced techniques have been garnered to improve online communication and to promote the security, comfort, and efficiency of ITS. Of primary importance to the effective application of ITS is the communication protocol used. A fascinating development is that the yesterday's Global System for Mobile Communication protocol is being replaced by the Universal Mobile Telecommunication System protocol, which is the third-generation mobile technology. This article attempts to identify a suitable communication system for ITS applications. It is impracticable to substantially modify the original UMTS-IMS-AKA protocol which is in practice because it can disturb the operation of the current system, and thus we explore other possibilities through this research. We investigate a novel protocol to make the original UMTS-IMS-AKA protocol compliant with ITS as well as adaptable into the current UMTS protocol.

Data acquisition and meter unit based in wifi communication protocol

Directory of Open Access Journals (Sweden)

Gerardo Cázarez Ayala

2012-05-01

Full Text Available Without doubt, the competitive fast rhythm of the industries is one of the main causes helped bring to the accelerated growth of the electronic technology and the communication. The need to develop new products with a best quality, cheaper and faster as assure and increase the quality of the products in the international markets, requires of new technologies to the metering, monitoring and control of their production processes, of which finality is to improve the processes to guaranteed their products in the market in the less time possible, the best quality and low cost for the final consumer. This work is based in the design and implementation of a Wireless Data Acquisition Unit based in WiFi protocol, which is oriented to meter, monitoring and the control of processes in the industry, commercial and the home automation applications, using one of the wirelessprotocols with the biggest acceptance in the market, with the main objective of to take advantage of the installed physical infrastructure in the place of the application, like industry, company or house. The Unit is based in the RN-131G, a Roving Network company module, which is able to work in stand-alone mode with ultralow power consummation and supporting the IEEE 802.11b/g protocols, in which is possible to achieve transfer rates of up to 11 Mbps and 54 Mbps in /b & /g specifications respectively. Whit this unit is possible to meter up to 5 analogs signals with 14 bits precision and has include a temperature and relative humidity sensors. This unit can meter two digital signals and act mean two digitals outputs, and gas include an USB port for communication and programming tasks.

A Secure Cluster-Based Multipath Routing Protocol for WMSNs

Directory of Open Access Journals (Sweden)

Jamal N. Al-Karaki

2011-04-01

Full Text Available The new characteristics of Wireless Multimedia Sensor Network (WMSN and its design issues brought by handling different traffic classes of multimedia content (video streams, audio, and still images as well as scalar data over the network, make the proposed routing protocols for typical WSNs not directly applicable for WMSNs. Handling real-time multimedia data requires both energy efficiency and QoS assurance in order to ensure efficient utility of different capabilities of sensor resources and correct delivery of collected information. In this paper, we propose a Secure Cluster-based Multipath Routing protocol for WMSNs, SCMR, to satisfy the requirements of delivering different data types and support high data rate multimedia traffic. SCMR exploits the hierarchical structure of powerful cluster heads and the optimized multiple paths to support timeliness and reliable high data rate multimedia communication with minimum energy dissipation. Also, we present a light-weight distributed security mechanism of key management in order to secure the communication between sensor nodes and protect the network against different types of attacks. Performance evaluation from simulation results demonstrates a significant performance improvement comparing with existing protocols (which do not even provide any kind of security feature in terms of average end-to-end delay, network throughput, packet delivery ratio, and energy consumption.

Toward Synthesis, Analysis, and Certification of Security Protocols

Science.gov (United States)

Schumann, Johann

2004-01-01

Implemented security protocols are basically pieces of software which are used to (a) authenticate the other communication partners, (b) establish a secure communication channel between them (using insecure communication media), and (c) transfer data between the communication partners in such a way that these data only available to the desired receiver, but not to anyone else. Such an implementation usually consists of the following components: the protocol-engine, which controls in which sequence the messages of the protocol are sent over the network, and which controls the assembly/disassembly and processing (e.g., decryption) of the data. the cryptographic routines to actually encrypt or decrypt the data (using given keys), and t,he interface to the operating system and to the application. For a correct working of such a security protocol, all of these components must work flawlessly. Many formal-methods based techniques for the analysis of a security protocols have been developed. They range from using specific logics (e.g.: BAN-logic [4], or higher order logics [12] to model checking [2] approaches. In each approach, the analysis tries to prove that no (or at least not a modeled intruder) can get access to secret data. Otherwise, a scenario illustrating the &tack may be produced. Despite the seeming simplicity of security protocols ("only" a few messages are sent between the protocol partners in order to ensure a secure communication), many flaws have been detected. Unfortunately, even a perfect protocol engine does not guarantee flawless working of a security protocol, as incidents show. Many break-ins and security vulnerabilities are caused by exploiting errors in the implementation of the protocol engine or the underlying operating system. Attacks using buffer-overflows are a very common class of such attacks. Errors in the implementation of exception or error handling can open up additional vulnerabilities. For example, on a website with a log-in screen

Analysis of several digital network technologies for hard real-time communications in nuclear plant

International Nuclear Information System (INIS)

Song, Ki Sang; No, Hee Chun

1999-01-01

Applying digital network technology for advanced nuclear plant requires deterministic communication for tight safety requirements, timely and reliable data delivery for operation critical and mission-critical characteristics of nuclear plant. Communication protocols, such as IEEE 802/4 Tiken Bus, IEEE 802/5 Token Ring, FDDI, and ARCnet, which have deterministic communication capability are partially applied to several nuclear power plants. Although digital communication technologies have many advantages, it is necessary to consider the noise immunity form electromagnetic interference (EMI), electrical interference, impulse noise, and heat noise before selecting specific digital network technology for nuclear plant. In this paper, we consider the token frame loss and data frame loss rate due to the link error event, frame size, and link data rate in different protocols, and evaluate the possibility of failure to meet the hard real-time requirement in nuclear plant. (author). 11 refs., 3 figs., 4 tabs

Interface Assignment-Based AODV Routing Protocol to Improve Reliability in Multi-Interface Multichannel Wireless Mesh Networks

Directory of Open Access Journals (Sweden)

Won-Suk Kim

2015-01-01

Full Text Available The utilization of wireless mesh networks (WMNs has greatly increased, and the multi-interface multichannel (MIMC technic has been widely used for the backbone network. Unfortunately, the ad hoc on-demand distance vector (AODV routing protocol defined in the IEEE 802.11s standard was designed for WMNs using the single-interface single-channel technic. So, we define a problem that happens when the legacy AODV is used in MIMC WMNs and propose an interface assignment-based AODV (IA-AODV in order to resolve that problem. IA-AODV, which is based on multitarget path request, consists of the PREQ prediction scheme, the PREQ loss recovery scheme, and the PREQ sender assignment scheme. A detailed operation according to various network conditions and services is introduced, and the routing efficiency and network reliability of a network using IA-AODV are analyzed over the presented system model. Finally, after a real-world test-bed for MIMC WMNs using the IA-AODV routing protocol is implemented, the various indicators of the network are evaluated through experiments. When the proposed routing protocol is compared with the existing AODV routing protocol, it performs the path update using only 14.33% of the management frames, completely removes the routing malfunction, and reduces the UDP packet loss ratio by 0.0012%.

Cryptanalysis and improvement of quantum broadcast communication and authentication protocol with a quantum one-time pad

International Nuclear Information System (INIS)

Liu Zhi-Hao; Chen Han-Wu

2016-01-01

The security of quantum broadcast communication (QBC) and authentication protocol based on Greenberger–Horne–Zeilinger (GHZ) state and quantum one-time pad is analyzed. It is shown that there are some security issues in this protocol. Firstly, an external eavesdropper can take the intercept–measure–resend attack strategy to eavesdrop on 0.369 bit of every bit of the identity string of each receiver without being detected. Meanwhile, 0.524 bit of every bit of the secret message can be eavesdropped on without being detected. Secondly, an inner receiver can take the intercept–measure–resend attack strategy to eavesdrop on half of the identity string of the other’s definitely without being checked. In addition, an alternative attack called the CNOT-operation attack is discussed. As for the multi-party QBC protocol, the attack efficiency increases with the increase of the number of users. Finally, the QBC protocol is improved to a secure one. (paper)

Eavesdropping on the "Ping-Pong" Quantum Communication Protocol Freely in a Noise Channel

OpenAIRE

Deng, Fu-Guo; Li, Xi-Han; Li, Chun-Yan; Zhou, Ping; Zhou, Hong-Yu

2005-01-01

We introduce an attack scheme for eavesdropping the ping-pong quantum communication protocol proposed by Bostr$\\ddot{o}$m and Felbinger [Phys. Rev. Lett. \\textbf{89}, 187902 (2002)] freely in a noise channel. The vicious eavesdropper, Eve, intercepts and measures the travel photon transmitted between the sender and the receiver. Then she replaces the quantum signal with a multi-photon signal in a same state, and measures the photons return with the measuring basis with which Eve prepares the ...

Communication of technical building systems. Interfaces, protocols and solutions; Kommunikation technischer Gebaeudesysteme. Schnittstellen, Protokolle und Loesungen

Energy Technology Data Exchange (ETDEWEB)

Kranz, H.R. [Siemens AG, Karlsruhe (Germany)

1995-12-31

In chapter 18 of the anthology about building control the communication between and with technical building systems is described. After the basics have been explained in the previous chapter interfaces, protocols and solutions are presented in this part. The following aspects are discussed: homogeneous and heterogeneous building automation systems, communication in the field of building automation, demands and characteristic numbers, open communication between heterogeneous systems, announcement and award procedures, protocol selection, FND - firm neutral data transmission system, PROFIBUS, ISP (InterOperable Systems Project) and Fieldbus Foundation with ``profile``; EIB (European Installation Bus), the standard bus for building system technology, BACNet (Building Automation Control Network) and EcheLON, open systems for building automation. (BWI) [Deutsch] Kapitel 18 des Sammelbandes ueber Building Control geht auf das Thema der Kommunikation zwischen und mit technischen Gebaeudesystemen ein. Nachdem im vorherigen Kapitel die Grundlagen besprochen wurden, wird im vorliegenden Teil auf Schnittstellen, Protokolle und Loesungen eingegangen. In diesem Zusammenhang werden folgenden Themenbereiche angesprochen: Homogene und heterogene GA-Systeme; Kommunikation in der Gebaeudeautomation; Anforderungen und Kennwert; offene Kommunikation heterogener Systeme; Ausschreibungs- und Vergabeprozeduren; Protokollauswahl; FND, das firmenneutrale Datenuebertragungsprotokoll; PROFIBUS, ISP und Fieldbus Foundation mit `Profil`; EIB, der Standardbus fuer die Gebaeudesystemtechnik; BACNet und EcheLON; Offene Systeme fuer die Gebaeudeautomation. (BWI)

STFTP: Secure TFTP Protocol for Embedded Multi-Agent Systems Communication

Directory of Open Access Journals (Sweden)

ZAGAR, D.

2013-05-01

Full Text Available Today's embedded systems have evolved into multipurpose devices moving towards an embedded multi-agent system (MAS infrastructure. With the involvement of MAS in embedded systems, one remaining issues is establishing communication between agents in low computational power and low memory embedded systems without present Embedded Operating System (EOS. One solution is the extension of an outdated Trivial File Transfer Protocol (TFTP. The main advantage of using TFTP in embedded systems is the easy implementation. However, the problem at hand is the overall lack of security mechanisms in TFTP. This paper proposes an extension to the existing TFTP in a form of added security mechanisms: STFTP. The authentication is proposed using Digest Access Authentication process whereas the data encryption can be performed by various cryptographic algorithms. The proposal is experimentally tested using two embedded systems based on micro-controller architecture. Communication is analyzed for authentication, data rate and transfer time versus various data encryption ciphers and files sizes. STFTP results in an expected drop in performance, which is in the range of similar encryption algorithms. The system could be improved by using embedded systems of higher computational power or by the use of hardware encryption modules.

Calf-raise senior: a new test for assessment of plantar flexor muscle strength in older adults: protocol, validity, and reliability.

Science.gov (United States)

André, Helô-Isa; Carnide, Filomena; Borja, Edgar; Ramalho, Fátima; Santos-Rocha, Rita; Veloso, António P

2016-01-01

This study aimed to develop a new field test protocol with a standardized measurement of strength and power in plantar flexor muscles targeted to functionally independent older adults, the calf-raise senior (CRS) test, and also evaluate its reliability and validity. Forty-one subjects aged 65 years and older of both sexes participated in five different cross-sectional studies: 1) pilot (n=12); 2) inter- and intrarater agreement (n=12); 3) construct (n=41); 4) criterion validity (n=33); and 5) test-retest reliability (n=41). Different motion parameters were compared in order to define a specifically designed protocol for seniors. Two raters evaluated each participant twice, and the results of the same individual were compared between raters and participants to assess the interrater and intrarater agreement. The validity and reliability studies involved three testing sessions that lasted 2 weeks, including a battery of functional fitness tests, CRS test in two occasions, accelerometry, and strength assessments in an isokinetic dynamometer. The CRS test presented an excellent test-retest reliability (intraclass correlation coefficient [ICC] =0.90, standard error of measurement =2.0) and interrater reliability (ICC =0.93-0.96), as well as a good intrarater agreement (ICC =0.79-0.84). Participants with better results in the CRS test were younger and presented higher levels of physical activity and functional fitness. A significant association between test results and all strength parameters (isometric, r =0.87, r 2 =0.75; isokinetic, r =0.86, r 2 =0.74; and rate of force development, r =0.77, r 2 =0.59) was shown. This study was successful in demonstrating that the CRS test can meet the scientific criteria of validity and reliability. The test can be a good indicator of ankle strength in older adults and proved to discriminate significantly between individuals with improved functionality and levels of physical activity.

Network-topology-adaptive quantum conference protocols

International Nuclear Information System (INIS)

Zhang Sheng; Wang Jian; Tang Chao-Jing; Zhang Quan

2011-01-01

As an important application of the quantum network communication, quantum multiparty conference has made multiparty secret communication possible. Previous quantum multiparty conference schemes based on quantum data encryption are insensitive to network topology. However, the topology of the quantum network significantly affects the communication efficiency, e.g., parallel transmission in a channel with limited bandwidth. We have proposed two distinctive protocols, which work in two basic network topologies with efficiency higher than the existing ones. We first present a protocol which works in the reticulate network using Greeberger—Horne—Zeilinger states and entanglement swapping. Another protocol, based on quantum multicasting with quantum data compression, which can improve the efficiency of the network, works in the star-like network. The security of our protocols is guaranteed by quantum key distribution and one-time-pad encryption. In general, the two protocols can be applied to any quantum network where the topology can be equivalently transformed to one of the two structures we propose in our protocols. (general)

A software defined RTU multi-protocol automatic adaptation data transmission method

Science.gov (United States)

Jin, Huiying; Xu, Xingwu; Wang, Zhanfeng; Ma, Weijun; Li, Sheng; Su, Yong; Pan, Yunpeng

2018-02-01

Remote terminal unit (RTU) is the core device of the monitor system in hydrology and water resources. Different devices often have different communication protocols in the application layer, which results in the difficulty in information analysis and communication networking. Therefore, we introduced the idea of software defined hardware, and abstracted the common feature of mainstream communication protocols of RTU application layer, and proposed a uniformed common protocol model. Then, various communication protocol algorithms of application layer are modularized according to the model. The executable codes of these algorithms are labeled by the virtual functions and stored in the flash chips of embedded CPU to form the protocol stack. According to the configuration commands to initialize the RTU communication systems, it is able to achieve dynamic assembling and loading of various application layer communication protocols of RTU and complete the efficient transport of sensor data from RTU to central station when the data acquisition protocol of sensors and various external communication terminals remain unchanged.

A reliable protocol for the isolation of viable, chondrogenically differentiated human mesenchymal stem cells from high-density pellet cultures.

Science.gov (United States)

Ullah, Mujib; Hamouda, Houda; Stich, Stefan; Sittinger, Michael; Ringe, Jochen

2012-12-01

Administration of chondrogenically differentiated mesenchymal stem cells (MSC) is discussed as a promising approach for the regenerative treatment of injured or diseased cartilage. The high-density pellet culture is the standard culture for chondrogenic differentiation, but cells in pellets secrete extracellular matrix (ECM) that they become entrapped in. Protocols for cell isolation from pellets often result in cell damage and dedifferentiation towards less differentiated MSC. Therefore, our aim was to develop a reliable protocol for the isolation of viable, chondrogenically differentiated MSC from high-density pellet cultures. Human bone marrow MSC were chondrogenically stimulated with transforming growth factor-β3, and the cartilaginous structure of the pellets was verified by alcian blue staining of cartilage proteoglycans, antibody staining of cartilage collagen type II, and quantitative real-time reverse-transcription polymerase chain reaction of the marker genes COL2A1 and SOX9. Trypsin and collagenases II and P were tested alone or in combination, and for different concentrations and times, to find a protocol for optimized pellet digestion. Whereas trypsin was not able to release viable cells, 90-min digestion with 300 U of collagenase II, 20 U of collagenase P, and 2 mM CaCl2 worked quite well and resulted in about 2.5×10(5) cells/pellet. The protocol was further optimized for the separation of released cells and ECM from each other. Cells were alcian blue and collagen type II positive and expressed COL2A1 and SOX9, verifying a chondrogenic character. However, they had different morphological shapes. The ECM was also uniformly alcian blue and collagen type II positive but showed different organizational and structural forms. To conclude, our protocol allows the reliable isolation of a defined number of viable, chondrogenically differentiated MSC from high-density pellet cultures. Such cells, as well as the ECM components, are of interest as

Hardening Stratum, the Bitcoin Pool Mining Protocol

Directory of Open Access Journals (Sweden)

Recabarren Ruben

2017-07-01

Full Text Available Stratum, the de-facto mining communication protocol used by blockchain based cryptocurrency systems, enables miners to reliably and efficiently fetch jobs from mining pool servers. In this paper we exploit Stratum’s lack of encryption to develop passive and active attacks on Bitcoin’s mining protocol, with important implications on the privacy, security and even safety of mining equipment owners. We introduce StraTap and ISP Log attacks, that infer miner earnings if given access to miner communications, or even their logs. We develop BiteCoin, an active attack that hijacks shares submitted by miners, and their associated payouts. We build BiteCoin on WireGhost, a tool we developed to hijack and surreptitiously maintain Stratum connections. Our attacks reveal that securing Stratum through pervasive encryption is not only undesirable (due to large overheads, but also ineffective: an adversary can predict miner earnings even when given access to only packet timestamps. Instead, we devise Bedrock, a minimalistic Stratum extension that protects the privacy and security of mining participants. We introduce and leverage the mining cookie concept, a secret that each miner shares with the pool and includes in its puzzle computations, and that prevents attackers from reconstructing or hijacking the puzzles.

Cryptanalysis of quantum broadcast communication and authentication protocol with a one-time pad

International Nuclear Information System (INIS)

Cao Ya; Gao Fei

2016-01-01

Chang et al . [ Chin. Phys. B 23 010305 (2014)] have proposed a quantum broadcast communication and authentication protocol. However, we find that an intercept-resend attack can be preformed successfully by a potential eavesdropper, who will be able to destroy the authentication function. Afterwards, he or she can acquire the secret transmitted message or even modify it while escaping detection, by implementing an efficient man-in-the-middle attack. Furthermore, we show a simple scheme to defend this attack, that is, applying non-reusable identity strings. (paper)

A reliable, practical, and economical protocol for inducing diarrhea and severe dehydration in the neonatal calf.

OpenAIRE

Walker, P G; Constable, P D; Morin, D E; Drackley, J K; Foreman, J H; Thurmon, J C

1998-01-01

Fifteen healthy, colostrum-fed, male dairy calves, aged 2 to 7 d were used in a study to develop a diarrhea protocol for neonatal calves that is reliable, practical, and economical. After instrumentation and recording baseline data, diarrhea and dehydration were induced by administering milk replacer [16.5 mL/kg of body weight (BW), PO], sucrose (2 g/kg in a 20% aqueous solution, p.o.), spironolactone and hydrochlorothiazide (1 mg/kg, PO) every 8 h, and furosemide (2 mg/kg, i.m., q6h). Calves...

DICOM image secure communications with Internet protocols IPv6 and IPv4.

Science.gov (United States)

Zhang, Jianguo; Yu, Fenghai; Sun, Jianyong; Yang, Yuanyuan; Liang, Chenwen

2007-01-01

Image-data transmission from one site to another through public network is usually characterized in term of privacy, authenticity, and integrity. In this paper, we first describe a general scenario about how image is delivered from one site to another through a wide-area network (WAN) with security features of data privacy, integrity, and authenticity. Second, we give the common implementation method of the digital imaging and communication in medicine (DICOM) image communication software library with IPv6/IPv4 for high-speed broadband Internet by using open-source software. Third, we discuss two major security-transmission methods, the IP security (IPSec) and the secure-socket layer (SSL) or transport-layer security (TLS), being used currently in medical-image-data communication with privacy support. Fourth, we describe a test schema of multiple-modality DICOM-image communications through TCP/IPv4 and TCP/IPv6 with different security methods, different security algorithms, and operating systems, and evaluate the test results. We found that there are tradeoff factors between choosing the IPsec and the SSL/TLS-based security implementation of IPv6/IPv4 protocols. If the WAN networks only use IPv6 such as in high-speed broadband Internet, the choice is IPsec-based security. If the networks are IPv4 or the combination of IPv6 and IPv4, it is better to use SSL/TLS security. The Linux platform has more security algorithms implemented than the Windows (XP) platform, and can achieve better performance in most experiments of IPv6 and IPv4-based DICOM-image communications. In teleradiology or enterprise-PACS applications, the Linux operating system may be the better choice as peer security gateways for both the IPsec and the SSL/TLS-based secure DICOM communications cross public networks.

Performance Analysis of TDMA Protocol in a Femtocell Network

Directory of Open Access Journals (Sweden)

Wanod Kumar

2014-07-01

Full Text Available In this paper, we evaluate the performance of TDMA (Time Division Multiple Access protocol using queuing theory in a femtocell network. The fair use of wireless channel among the users of network is carried out using TDMA protocol. The arrival of data packets from M communicating nodes becomes multiple Poisson process. The time slots of TDMA protocol represent c servers to communicate data packets coming from communicating nodes to the input of FAP (Femtocell Access Point. The service time of each server (time slot is exponentially distributed. This complete communication scenario using TDMA protocol is modeled using M/M/c queue. The performance of the protocol is evaluated in terms of mean number in system, average system delay and utilization for varying traffic intensity

Reliable multicast for the Grid: a case study in experimental computer science.

Science.gov (United States)

Nekovee, Maziar; Barcellos, Marinho P; Daw, Michael

2005-08-15

In its simplest form, multicast communication is the process of sending data packets from a source to multiple destinations in the same logical multicast group. IP multicast allows the efficient transport of data through wide-area networks, and its potentially great value for the Grid has been highlighted recently by a number of research groups. In this paper, we focus on the use of IP multicast in Grid applications, which require high-throughput reliable multicast. These include Grid-enabled computational steering and collaborative visualization applications, and wide-area distributed computing. We describe the results of our extensive evaluation studies of state-of-the-art reliable-multicast protocols, which were performed on the UK's high-speed academic networks. Based on these studies, we examine the ability of current reliable multicast technology to meet the Grid's requirements and discuss future directions.

Analysis of a security protocol in ?CRL

NARCIS (Netherlands)

J. Pang

2002-01-01

textabstractNeedham-Schroeder public-key protocol; With the growth and commercialization of the Internet, the security of communication between computers becomes a crucial point. A variety of security protocols based on cryptographic primitives are used to establish secure communication over

Development of a Standardized Kalamazoo Communication Skills Assessment Tool for Radiologists: Validation, Multisource Reliability, and Lessons Learned.

Science.gov (United States)

Brown, Stephen D; Rider, Elizabeth A; Jamieson, Katherine; Meyer, Elaine C; Callahan, Michael J; DeBenedectis, Carolynn M; Bixby, Sarah D; Walters, Michele; Forman, Sara F; Varrin, Pamela H; Forbes, Peter; Roussin, Christopher J

2017-08-01

The purpose of this study was to develop and test a standardized communication skills assessment instrument for radiology. The Delphi method was used to validate the Kalamazoo Communication Skills Assessment instrument for radiology by revising and achieving consensus on the 43 items of the preexisting instrument among an interdisciplinary team of experts consisting of five radiologists and four nonradiologists (two men, seven women). Reviewers assessed the applicability of the instrument to evaluation of conversations between radiology trainees and trained actors portraying concerned parents in enactments about bad news, radiation risks, and diagnostic errors that were video recorded during a communication workshop. Interrater reliability was assessed by use of the revised instrument to rate a series of enactments between trainees and actors video recorded in a hospital-based simulator center. Eight raters evaluated each of seven different video-recorded interactions between physicians and parent-actors. The final instrument contained 43 items. After three review rounds, 42 of 43 (98%) items had an average rating of relevant or very relevant for bad news conversations. All items were rated as relevant or very relevant for conversations about error disclosure and radiation risk. Reliability and rater agreement measures were moderate. The intraclass correlation coefficient range was 0.07-0.58; mean, 0.30; SD, 0.13; and median, 0.30. The range of weighted kappa values was 0.03-0.47; mean, 0.23; SD, 0.12; and median, 0.22. Ratings varied significantly among conversations (χ 2 6 = 1186; p communication skills assessment instrument is highly relevant for radiology, having moderate interrater reliability. These findings have important implications for assessing the relational competencies of radiology trainees.

Two-step quantum direct communication protocol using the Einstein- Podolsky-Rosen pair block

CERN Document Server

Fu Guo Deng; Xiao Shu Liu; 10.1103/PhysRevA.68.042317

2003-01-01

A protocol for quantum secure direct communication using blocks of Einstein-Podolsky-Rosen (EPR) pairs is proposed. A set of ordered N EPR pairs is used as a data block for sending secret message directly. The ordered N EPR set is divided into two particle sequences, a checking sequence and a message-coding sequence. After transmitting the checking sequence, the two parties of communication check eavesdropping by measuring a fraction of particles randomly chosen, with random choice of two sets of measuring bases. After insuring the security of the quantum channel, the sender Alice encodes the secret message directly on the message-coding sequence and sends them to Bob. By combining the checking and message-coding sequences together, Bob is able to read out the encoded messages directly. The scheme is secure because an eavesdropper cannot get both sequences simultaneously. We also discuss issues in a noisy channel. (30 refs).

Self-Adaptive Context Aware Routing Protocol for Unicast Communication in Delay and Tolerant Network

Directory of Open Access Journals (Sweden)

Yunbo Chen

2014-05-01

Full Text Available At present, most of research works in mobile network focus on the network overhead of the known path which exists between the sender and the receiver. However, the trend of the current practical application demands is becoming increasingly distributed and decentralized. The Delay and Tolerant Network (DTN just comes out of such background of the conflicts between them. The DTN could effectively eliminate the gap between the mobile network and the practical application demands. In this paper, a Self-Adaptive Context Aware Routing Protocol (SACARP for the unicast communication in delay and tolerant networks is presented. Meanwhile, according to the real-time context information of DTN, the Kalman filter theory is introduced to predict the information state of mobility for the optional message ferrying node, and then gives the optimal selection strategy of the message ferrying nodes. The simulation experiments have shown that, compared to the familiar single- copy and multi-copy protocols, the SACARP proposed in this paper has better transmission performance and stability, especially when the network is free, the protocol would keep a good performance with fewer connections and less buffer space.

Fine-Grained vs. Average Reliability for V2V Communications around Intersections

OpenAIRE

Abdulla, Mouhamed; Wymeersch, Henk

2017-01-01

Intersections are critical areas of the transportation infrastructure associated with 47% of all road accidents. Vehicle-to-vehicle (V2V) communication has the potential of preventing up to 35% of such serious road collisions. In fact, under the 5G/LTE Rel.15+ standardization, V2V is a critical use-case not only for the purpose of enhancing road safety, but also for enabling traffic efficiency in modern smart cities. Under this anticipated 5G definition, high reliability of 0.99999 is expecte...

Security Protocols in a Nutshell

OpenAIRE

Toorani, Mohsen

2016-01-01

Security protocols are building blocks in secure communications. They deploy some security mechanisms to provide certain security services. Security protocols are considered abstract when analyzed, but they can have extra vulnerabilities when implemented. This manuscript provides a holistic study on security protocols. It reviews foundations of security protocols, taxonomy of attacks on security protocols and their implementations, and different methods and models for security analysis of pro...

The Control Packet Collision Avoidance Algorithm for the Underwater Multichannel MAC Protocols via Time-Frequency Masking

Directory of Open Access Journals (Sweden)

Yang Yu

2016-01-01

Full Text Available Establishing high-speed and reliable underwater acoustic networks among multiunmanned underwater vehicles (UUVs is basic to realize cooperative and intelligent control among different UUVs. Nevertheless, different from terrestrial network, the propagation speed of the underwater acoustic network is 1500 m/s, which makes the design of the underwater acoustic network MAC protocols a big challenge. In accordance with multichannel MAC protocols, data packets and control packets are transferred through different channels, which lowers the adverse effect of acoustic network and gradually becomes the popular issues of underwater acoustic networks MAC protocol research. In this paper, we proposed a control packet collision avoidance algorithm utilizing time-frequency masking to deal with the control packets collision in the control channel. This algorithm is based on the scarcity of the noncoherent underwater acoustic communication signals, which regards collision avoiding as separation of the mixtures of communication signals from different nodes. We first measure the W-Disjoint Orthogonality of the MFSK signals and the simulation result demonstrates that there exists time-frequency mask which can separate the source signals from the mixture of the communication signals. Then we present a pairwise hydrophones separation system based on deep networks and the location information of the nodes. Consequently, the time-frequency mask can be estimated.

The Study on the Communication Network of Wide Area Measurement System in Electricity Grid

Science.gov (United States)

Xiaorong, Cheng; Ying, Wang; Yangdan, Ni

Wide area measurement system(WAMS) is a fundamental part of security defense in Smart Grid, and the communication system of WAMS is an important part of Electric power communication network. For a large regional network is concerned, the real-time data which is transferred in the communication network of WAMS will affect the safe operation of the power grid directly. Therefore, WAMS raised higher requirements for real-time, reliability and security to its communication network. In this paper, the architecture of WASM communication network was studied according to the seven layers model of the open systems interconnection(OSI), and the network architecture was researched from all levels. We explored the media of WAMS communication network, the network communication protocol and network technology. Finally, the delay of the network were analyzed.

Double C-NOT attack and counterattack on `Three-step semi-quantum secure direct communication protocol'

Science.gov (United States)

Gu, Jun; Lin, Po-hua; Hwang, Tzonelih

2018-07-01

Recently, Zou and Qiu (Sci China Phys Mech Astron 57:1696-1702, 2014) proposed a three-step semi-quantum secure direct communication protocol allowing a classical participant who does not have a quantum register to securely send his/her secret message to a quantum participant. However, this study points out that an eavesdropper can use the double C-NOT attack to obtain the secret message. To solve this problem, a modification is proposed.

Performance and Reliability of DSRC Vehicular Safety Communication: A Formal Analysis

Directory of Open Access Journals (Sweden)

2009-02-01

Full Text Available IEEE- and ASTM-adopted dedicated short range communications (DSRC standard toward 802.11p is a key enabling technology for the next generation of vehicular safety communication. Broadcasting of safety messages is one of the fundamental services in DSRC. There have been numerous publications addressing design and analysis of such broadcast ad hoc system based on the simulations. For the first time, an analytical model is proposed in this paper to evaluate performance and reliability of IEEE 802.11a-based vehicle-to-vehicle (V2V safety-related broadcast services in DSRC system on highway. The proposed model takes two safety services with different priorities, nonsaturated message arrival, hidden terminal problem, fading transmission channel, transmission range, IEEE 802.11 backoff counter process, and highly mobile vehicles on highway into account. Based on the solutions to the proposed analytic model, closed-form expressions of channel throughput, transmission delay, and packet reception rates are derived. From the obtained numerical results under various offered traffic and network parameters, new insights and enhancement suggestions are given.

Object-oriented communications

International Nuclear Information System (INIS)

Chapman, L.J.

1989-01-01

OOC is a high-level communications protocol based on the object-oriented paradigm. OOC's syntax, semantics, and pragmatics balance simplicity and expressivity for controls environments. While natural languages are too complex, computer protocols are often insufficiently expressive. An object-oriented communications philosophy provides a base for building the necessary high-level communications primitives like I don't understand and the current value of X is K. OOC is sufficiently flexible to express data acquisition, control requests, alarm messages, and error messages in a straightforward generic way. It can be used in networks, for inter-task communication, and even for intra-task communication

Quantum communication in noisy environments

International Nuclear Information System (INIS)

Aschauer, H.

2004-01-01

In this thesis, we investigate how protocols in quantum communication theory are influenced by noise. Specifically, we take into account noise during the transmission of quantum information and noise during the processing of quantum information. We describe three novel quantum communication protocols which can be accomplished efficiently in a noisy environment: (1) Factorization of Eve: We show that it is possible to disentangle transmitted qubits a posteriori from the quantum channel's degrees of freedom. (2) Cluster state purification: We give multi-partite entanglement purification protocols for a large class of entangled quantum states. (3) Entanglement purification protocols from quantum codes: We describe a constructive method to create bipartite entanglement purification protocols form quantum error correcting codes, and investigate the properties of these protocols, which can be operated in two different modes, which are related to quantum communication and quantum computation protocols, respectively

Cost-optimization of the IPv4 zeroconf protocol

NARCIS (Netherlands)

Bohnenkamp, H.C.; van der Stok, Peter; Hermanns, H.; Vaandrager, Frits

2003-01-01

This paper investigates the tradeoff between reliability and effectiveness for the IPv4 Zeroconf protocol, proposed by Cheshire/Adoba/Guttman in 2002, dedicated to the selfconfiguration of IP network interfaces. We develop a simple stochastic cost model of the protocol, where reliability is measured

e-SCP-ECG+ Protocol: An Expansion on SCP-ECG Protocol for Health Telemonitoring—Pilot Implementation

Directory of Open Access Journals (Sweden)

George J. Mandellos

2010-01-01

Full Text Available Standard Communication Protocol for Computer-assisted Electrocardiography (SCP-ECG provides standardized communication among different ECG devices and medical information systems. This paper extends the use of this protocol in order to be included in health monitoring systems. It introduces new sections into SCP-ECG structure for transferring data for positioning, allergies, and five additional biosignals: noninvasive blood pressure (NiBP, body temperature (Temp, Carbon dioxide (CO2, blood oxygen saturation (SPO2, and pulse rate. It also introduces new tags in existing sections for transferring comprehensive demographic data. The proposed enhanced version is referred to as e-SCP-ECG+ protocol. This paper also considers the pilot implementation of the new protocol as a software component in a Health Telemonitoring System.

Advanced Communication and Networking Technologies for Mars Exploration

Science.gov (United States)

Bhasin, Kul; Hayden, Jeff; Agre, Jonathan R.; Clare, Loren P.; Yan, Tsun-Yee

2001-01-01

Next-generation Mars communications networks will provide communications and navigation services to a wide variety of Mars science vehicles including: spacecraft that are arriving at Mars, spacecraft that are entering and descending in the Mars atmosphere, scientific orbiter spacecraft, spacecraft that return Mars samples to Earth, landers, rovers, aerobots, airplanes, and sensing pods. In the current architecture plans, the communication services will be provided using capabilities deployed on the science vehicles as well as dedicated communication satellites that will together make up the Mars network. This network will evolve as additional vehicles arrive, depart or end their useful missions. Cost savings and increased reliability will result from the ability to share communication services between missions. This paper discusses the basic architecture that is needed to support the Mars Communications Network part of NASA's Space Science Enterprise (SSE) communications architecture. The network may use various networking technologies such as those employed in the terrestrial Internet, as well as special purpose deep-space protocols to move data and commands autonomously between vehicles, at disparate Mars vicinity sites (on the surface or in near-Mars space) and between Mars vehicles and earthbound users. The architecture of the spacecraft on-board local communications is being reconsidered in light of these new networking requirements. The trend towards increasingly autonomous operation of the spacecraft is aimed at reducing the dependence on resource scheduling provided by Earth-based operators and increasing system fault tolerance. However, these benefits will result in increased communication and software development requirements. As a result, the envisioned Mars communications infrastructure requires both hardware and protocol technology advancements. This paper will describe a number of the critical technology needs and some of the ongoing research

Integrated Evaluation of Reliability and Power Consumption of Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Antônio Dâmaso

2017-11-01

Full Text Available Power consumption is a primary interest in Wireless Sensor Networks (WSNs, and a large number of strategies have been proposed to evaluate it. However, those approaches usually neither consider reliability issues nor the power consumption of applications executing in the network. A central concern is the lack of consolidated solutions that enable us to evaluate the power consumption of applications and the network stack also considering their reliabilities. To solve this problem, we introduce a fully automatic solution to design power consumption aware WSN applications and communication protocols. The solution presented in this paper comprises a methodology to evaluate the power consumption based on the integration of formal models, a set of power consumption and reliability models, a sensitivity analysis strategy to select WSN configurations and a toolbox named EDEN to fully support the proposed methodology. This solution allows accurately estimating the power consumption of WSN applications and the network stack in an automated way.

Integrated Evaluation of Reliability and Power Consumption of Wireless Sensor Networks

Science.gov (United States)

Dâmaso, Antônio; Maciel, Paulo

2017-01-01

Power consumption is a primary interest in Wireless Sensor Networks (WSNs), and a large number of strategies have been proposed to evaluate it. However, those approaches usually neither consider reliability issues nor the power consumption of applications executing in the network. A central concern is the lack of consolidated solutions that enable us to evaluate the power consumption of applications and the network stack also considering their reliabilities. To solve this problem, we introduce a fully automatic solution to design power consumption aware WSN applications and communication protocols. The solution presented in this paper comprises a methodology to evaluate the power consumption based on the integration of formal models, a set of power consumption and reliability models, a sensitivity analysis strategy to select WSN configurations and a toolbox named EDEN to fully support the proposed methodology. This solution allows accurately estimating the power consumption of WSN applications and the network stack in an automated way. PMID:29113078

Agent Communications using Distributed Metaobjects

Energy Technology Data Exchange (ETDEWEB)

Goldsmith, Steven Y.; Spires, Shannon V.

1999-06-10

There are currently two proposed standards for agent communication languages, namely, KQML (Finin, Lobrou, and Mayfield 1994) and the FIPA ACL. Neither standard has yet achieved primacy, and neither has been evaluated extensively in an open environment such as the Internet. It seems prudent therefore to design a general-purpose agent communications facility for new agent architectures that is flexible yet provides an architecture that accepts many different specializations. In this paper we exhibit the salient features of an agent communications architecture based on distributed metaobjects. This architecture captures design commitments at a metaobject level, leaving the base-level design and implementation up to the agent developer. The scope of the metamodel is broad enough to accommodate many different communication protocols, interaction protocols, and knowledge sharing regimes through extensions to the metaobject framework. We conclude that with a powerful distributed object substrate that supports metaobject communications, a general framework can be developed that will effectively enable different approaches to agent communications in the same agent system. We have implemented a KQML-based communications protocol and have several special-purpose interaction protocols under development.

Fundamental limits of repeaterless quantum communications

Science.gov (United States)

Pirandola, Stefano; Laurenza, Riccardo; Ottaviani, Carlo; Banchi, Leonardo

2017-01-01

Quantum communications promises reliable transmission of quantum information, efficient distribution of entanglement and generation of completely secure keys. For all these tasks, we need to determine the optimal point-to-point rates that are achievable by two remote parties at the ends of a quantum channel, without restrictions on their local operations and classical communication, which can be unlimited and two-way. These two-way assisted capacities represent the ultimate rates that are reachable without quantum repeaters. Here, by constructing an upper bound based on the relative entropy of entanglement and devising a dimension-independent technique dubbed ‘teleportation stretching', we establish these capacities for many fundamental channels, namely bosonic lossy channels, quantum-limited amplifiers, dephasing and erasure channels in arbitrary dimension. In particular, we exactly determine the fundamental rate-loss tradeoff affecting any protocol of quantum key distribution. Our findings set the limits of point-to-point quantum communications and provide precise and general benchmarks for quantum repeaters. PMID:28443624

On Reliable and Efficient Data Gathering Based Routing in Underwater Wireless Sensor Networks.

Science.gov (United States)

Liaqat, Tayyaba; Akbar, Mariam; Javaid, Nadeem; Qasim, Umar; Khan, Zahoor Ali; Javaid, Qaisar; Alghamdi, Turki Ali; Niaz, Iftikhar Azim

2016-08-30

This paper presents cooperative routing scheme to improve data reliability. The proposed protocol achieves its objective, however, at the cost of surplus energy consumption. Thus sink mobility is introduced to minimize the energy consumption cost of nodes as it directly collects data from the network nodes at minimized communication distance. We also present delay and energy optimized versions of our proposed RE-AEDG to further enhance its performance. Simulation results prove the effectiveness of our proposed RE-AEDG in terms of the selected performance matrics.

Interobserver reliability of the 'Welfare Quality(®) Animal Welfare Assessment Protocol for Growing Pigs'.

Science.gov (United States)

Czycholl, I; Kniese, C; Büttner, K; Beilage, E Grosse; Schrader, L; Krieter, J

2016-01-01

The present paper focuses on evaluating the interobserver reliability of the 'Welfare Quality(®) Animal Welfare Assessment Protocol for Growing Pigs'. The protocol for growing pigs mainly consists of a Qualitative Behaviour Assessment (QBA), direct behaviour observations (BO) carried out by instantaneous scan sampling and checks for different individual parameters (IP), e.g. presence of tail biting, wounds and bursitis. Three trained observers collected the data by performing 29 combined assessments, which were done at the same time and on the same animals; but they were carried out completely independent of each other. The findings were compared by the calculation of Spearman Rank Correlation Coefficients (RS), Intraclass Correlation Coefficients (ICC), Smallest Detectable Changes (SDC) and Limits of Agreements (LoA). There was no agreement found concerning the adjectives belonging to the QBA (e.g. active: RS: 0.50, ICC: 0.30, SDC: 0.38, LoA: -0.05 to 0.45; fearful: RS: 0.06, ICC: 0.0, SDC: 0.26, LoA: -0.20 to 0.30). In contrast, the BO showed good agreement (e.g. social behaviour: RS: 0.45, ICC: 0.50, SDC: 0.09, LoA: -0.09 to 0.03 use of enrichment material: RS: 0.75, ICC: 0.68, SDC: 0.06, LoA: -0.03 to 0.03). Overall, observers agreed well in the IP, e.g. tail biting (RS: 0.52, ICC: 0.88; SDC: 0.05, LoA: -0.01 to 0.02) and wounds (RS: 0.43, ICC: 0.59, SDC: 0.10, LoA: -0.09 to 0.10). The parameter bursitis showed great differences (RS: 0.10, ICC: 0.0, SDC: 0.35, LoA: -0.37 to 0.40), which can be explained by difficulties in the assessment when the animals moved around quickly or their legs were soiled. In conclusion, the interobserver reliability was good in the BO and most IP, but not for the parameter bursitis and the QBA.

Reliability in automotive ethernet networks

DEFF Research Database (Denmark)

Soares, Fabio L.; Campelo, Divanilson R.; Yan, Ying

2015-01-01

This paper provides an overview of in-vehicle communication networks and addresses the challenges of providing reliability in automotive Ethernet in particular.......This paper provides an overview of in-vehicle communication networks and addresses the challenges of providing reliability in automotive Ethernet in particular....

Communications standards

CERN Document Server

Stokes, A V

1986-01-01

Communications Standards deals with the standardization of computer communication networks. This book examines the types of local area networks (LANs) that have been developed and looks at some of the relevant protocols in more detail. The work of Project 802 is briefly discussed, along with a protocol which has developed from one of the LAN standards and is now a de facto standard in one particular area, namely the Manufacturing Automation Protocol (MAP). Factors that affect the usage of networks, such as network management and security, are also considered. This book is divided into three se

Formalization of Quantum Protocols using Coq

Directory of Open Access Journals (Sweden)

Jaap Boender

2015-11-01

Full Text Available Quantum Information Processing, which is an exciting area of research at the intersection of physics and computer science, has great potential for influencing the future development of information processing systems. The building of practical, general purpose Quantum Computers may be some years into the future. However, Quantum Communication and Quantum Cryptography are well developed. Commercial Quantum Key Distribution systems are easily available and several QKD networks have been built in various parts of the world. The security of the protocols used in these implementations rely on information-theoretic proofs, which may or may not reflect actual system behaviour. Moreover, testing of implementations cannot guarantee the absence of bugs and errors. This paper presents a novel framework for modelling and verifying quantum protocols and their implementations using the proof assistant Coq. We provide a Coq library for quantum bits (qubits, quantum gates, and quantum measurement. As a step towards verifying practical quantum communication and security protocols such as Quantum Key Distribution, we support multiple qubits, communication and entanglement. We illustrate these concepts by modelling the Quantum Teleportation Protocol, which communicates the state of an unknown quantum bit using only a classical channel.

Data communications and computer communications network

International Nuclear Information System (INIS)

Kim, Jang Gwon; Gu, Chang Hoe

2005-03-01

This textbook is composed of twelve chapters, which are communication network introduction, foundation of data communication, data link control, circuit switching system, packet switching system, multiple access communication system, protocol and architecture, LAN, MAN communication network, integrated service digital network, internet and Asymmetric digital subscriber Line and Wireless Local Loop. Each chapter has the introduction of the technique, structure, function and practice problems. It also has the appendix on electricity and communication standards organization, characteristic table and glossary.

Communication-Gateway Software For NETEX, DECnet, And TCP/IP

Science.gov (United States)

Keith, B.; Ferry, D.; Fendler, E.

1990-01-01

Communications gateway software, GATEWAY, provides process-to-process communication between remote applications programs in different protocol domains. Communicating peer processes may be resident on any paired combination of NETEX, DECnet, or TCP/IP hosts. Provides necessary mapping from one protocol to another and facilitates practical intermachine communications in cost-effective manner by eliminating need to standardize on single protocol or to implement multiple protocols in host computers. Written in Ada.

Communication Protocol for Advanced Prosthesis Components

OpenAIRE

Karnå, David

2007-01-01

It would be of great value for the prosthesis industry to achieve an open standard for communication in upper limb prostheses. Cooperation between NTNU and the University of New Brunswick has resulted in a functional requirements specification for such a standard, SCIP(Standardised Communication Interface in Prostheses). The special challenges for communication in a prosthesis system are possible noisy environments, high demands for light weight, safety for the user and the fact that devices ...

A Conflict-Free Low-Jitter Guaranteed-Rate MAC Protocol for Base-Station Communications in Wireless Mesh Networks

Science.gov (United States)

Szymanski, T. H.

A scheduling algorithm and MAC protocol which provides low-jitter guaranteed-rate (GR) communications between base-stations (BS) in a Wireless Mesh Network (WMN) is proposed. The protocol can provision long-term multimedia services such as VOIP, IPTV, or Video-on-Demand. The time-axis is partitioned into scheduling frames with F time-slots each. A directional antennae scheme is used to provide each directed link with a fixed transmission rate. A protocol such as IntServ is used to provision resources along an end-to-end path of BSs for GR sessions. The Guaranteed Rates between the BSs are then specified in a doubly stochastic traffic rate matrix, which is recursively decomposed to yield a low-jitter GR frame transmission schedule. In the resulting schedule, the end-to-end delay and jitter are small and bounded, and the cell loss rate due to primary scheduling conflicts is zero. For dual-channel WMNs, the MAC protocol can achieve 100% utilization, as well as near-minimal queueing delays and near minimal delay jitter. The scheduling time complexity is O(NFlogNF), where N is the number of BSs. Extensive simulation results are presented.

Interoperative fundus image and report sharing in compliance with integrating the healthcare enterprise conformance and web access todigital imaging and communication in medicinepersistent object protocol

Directory of Open Access Journals (Sweden)

Hui-Qun Wu

2013-12-01

Full Text Available AIM:To address issues in interoperability between different fundus image systems, we proposed a web eye-picture archiving and communication system (PACS framework in conformance with digital imaging and communication in medicine (DICOM and health level 7 (HL7 protocol to realize fundus images and reports sharing and communication through internet.METHODS: Firstly, a telemedicine-based eye care work flow was established based on integrating the healthcare enterprise (IHE Eye Care technical framework. Then, a browser/server architecture eye-PACS system was established in conformance with the web access to DICOM persistent object (WADO protocol, which contains three tiers.RESULTS:In any client system installed with web browser, clinicians could log in the eye-PACS to observe fundus images and reports. Multipurpose internet mail extensions (MIME type of a structured report is saved as pdf/html with reference link to relevant fundus image using the WADO syntax could provide enough information for clinicians. Some functions provided by open-source Oviyam could be used to query, zoom, move, measure, view DICOM fundus images.CONCLUSION:Such web eye-PACS in compliance to WADO protocol could be used to store and communicate fundus images and reports, therefore is of great significance for teleophthalmology.

A reliable, practical, and economical protocol for inducing diarrhea and severe dehydration in the neonatal calf.

Science.gov (United States)

Walker, P G; Constable, P D; Morin, D E; Drackley, J K; Foreman, J H; Thurmon, J C

1998-07-01

Fifteen healthy, colostrum-fed, male dairy calves, aged 2 to 7 d were used in a study to develop a diarrhea protocol for neonatal calves that is reliable, practical, and economical. After instrumentation and recording baseline data, diarrhea and dehydration were induced by administering milk replacer [16.5 mL/kg of body weight (BW), PO], sucrose (2 g/kg in a 20% aqueous solution, p.o.), spironolactone and hydrochlorothiazide (1 mg/kg, PO) every 8 h, and furosemide (2 mg/kg, i.m., q6h). Calves were administered sucrose and diuretic agents for 48 h to induce diarrhea and severe dehydration. Clinical changes after 48 h were severe watery diarrhea, severe depression, and marked dehydration (mean, 14% BW loss). Cardiac output, stroke volume, mean central venous pressure, plasma volume, thiocyanate space, blood pH and bicarbonate concentration, base excess, serum chloride concentration, and fetlock temperature were decreased. Plasma lactate concentration, hematocrit, and serum potassium, creatinine, phosphorus, total protein and albumin concentrations were increased. This non-infectious calf diarrhea protocol has a 100% response rate, while providing a consistent and predictable hypovolemic state with diarrhea that reflects most of the clinicopathologic changes observed in osmotic/maldigestive diarrhea caused by infection with rotavirus, coronavirus or cryptosporidia. Limitations of the protocol, when compared to infectious diarrhea models, include failure to induce a severe metabolic acidosis, absence of hyponatremia, renal instead of enteric loss of chloride, renal as well as enteric loss of free water, absence of profound clinical depression and suspected differences in the morphologic and functional effect on intestinal epithelium. Despite these differences, the sucrose/diuretic protocol should be useful in the initial screening of new treatment modalities for calf diarrhea. To confirm their efficacy, the most effective treatment methods should then be examined in

Plastic optical fiber serial communications link for distributed control system

Science.gov (United States)

Saxena, Piyush; Sharangpani, K. K.; Vora, H. S.; Nakhe, S. V.; Jain, R.; Shenoy, N. M.; Bhatnagar, R.; Shirke, N. D.

2001-09-01

One of the most common interface for communications specified is RS 232C standard. Though widely accepted, RS232 has limited transmission speed, range and networking capabilities. RS 422 standard overcomes limitations by using differential signal lines. In automation of the operation of gas discharge lasers, multiple processors are used for control of lasers, cooling system, vacuum system etc. High EMI generated by lasers interfere through galvanic transmission or by radiation over the length of cables, and hang up operation of processors or control PC. A serial communications link was designed eliminating copper transmission media, using plastic optical fiber cables and components, to connect local controllers with the master PC working on RS232 protocols. The paper discusses the design and implementation of a high ly reliable EMI harden serial communications link.

On Reliable and Efficient Data Gathering Based Routing in Underwater Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Tayyaba Liaqat

2016-08-01

Full Text Available This paper presents cooperative routing scheme to improve data reliability. The proposed protocol achieves its objective, however, at the cost of surplus energy consumption. Thus sink mobility is introduced to minimize the energy consumption cost of nodes as it directly collects data from the network nodes at minimized communication distance. We also present delay and energy optimized versions of our proposed RE-AEDG to further enhance its performance. Simulation results prove the effectiveness of our proposed RE-AEDG in terms of the selected performance matrics.

Reliability assessment of fiber optic communication lines depending on external factors and diagnostic errors

Science.gov (United States)

Bogachkov, I. V.; Lutchenko, S. S.

2018-05-01

The article deals with the method for the assessment of the fiber optic communication lines (FOCL) reliability taking into account the effect of the optical fiber tension, the temperature influence and the built-in diagnostic equipment errors of the first kind. The reliability is assessed in terms of the availability factor using the theory of Markov chains and probabilistic mathematical modeling. To obtain a mathematical model, the following steps are performed: the FOCL state is defined and validated; the state graph and system transitions are described; the system transition of states that occur at a certain point is specified; the real and the observed time of system presence in the considered states are identified. According to the permissible value of the availability factor, it is possible to determine the limiting frequency of FOCL maintenance.

An initial reliability and validity study of the Interaction, Communication, and Literacy Skills Audit.

Science.gov (United States)

El-Choueifati, Nisrine; Purcell, Alison; McCabe, Patricia; Heard, Robert; Munro, Natalie

2014-06-01

Early childhood educators (ECEs) have an important role in promoting positive outcomes for children's language and literacy development. This paper reports the development of a new tool, The Interaction Communication and Literacy (ICL) Skills Audit, and pilots its reliability and validity. Intra- and inter-rater reliability was examined by three speech-language pathologists (SLPs). Five skill areas relating to ECE language and literacy practice were rated. The face and content validity of the ICL Skills Audit was examined by expert SLPs (n = 8) and expert ECEs (n = 4) via questionnaire. The overall intra-rater reliability for the ICL Skills Audit was excellent with percentage close agreement (PCA) of 91-94. Inter-rater agreement was PCA 68-80. Expert SLPs and ECEs agreed that the content was comprehensive and practical. Based on this preliminary study, the ICL Skills Audit appears to be a promising tool that can be used by SLPs and ECEs in collaboration to measure the skills of ECEs in the areas of language and literacy support. Future psychometric and outcome research on the revised ICL Skills Audit is warranted.

The impact of protocol on nurses' role stress: a longitudinal perspective.

Science.gov (United States)

Dodd-McCue, Diane; Tartaglia, Alexander; Veazey, Kenneth W; Streetman, Pamela S

2005-04-01

The study examined the impact of a protocol directed at increasing organ donation on the role stress and work attitudes of critical care nurses involved in potential organ donation cases. The research examined whether the protocol could positively affect nurses' perceptions of role stress, and if so, could the work environment improvements be sustained over time. The Family Communication Coordinator (FCC) protocol promotes effective communication during potential organ donation cases using a multidisciplinary team approach. Previous research found it associated with improved donation outcomes and with improved perceptions of role stress by critical care nurses. However, the previous study lacked methodological rigor necessary to determine causality and sustainability over time. The study used a quasi-experimental prospective longitudinal design. The sample included critical care nurses who had experience with potential organ donation cases with the protocol. Survey data were collected at 4 points over 2 years. Surveys used previously validated and reliable measures of role stress (role ambiguity, role conflict, role overload) and work attitudes (commitment, satisfaction). Interviews supplemented these data. The nurses' perceptions of role stress associated with potential organ donation cases dramatically dropped after the protocol was implemented. All measures of role stress, particularly role ambiguity and role conflict, showed statistically significant and sustained improvement. Nurses' professional, unit, and hospital commitment and satisfaction reflect an increasingly positive workplace. The results demonstrate that the FCC protocol positively influenced the workplace through its impact on role stress over the first 2 years following its implementation. The findings suggest that similar protocols may be appropriate in improving the critical care environment by reducing the stress and uncertainty of professionals involved in other end-of-life situations. However

Epistemic Protocols for Distributed Gossiping

Directory of Open Access Journals (Sweden)

Krzysztof R. Apt

2016-06-01

Full Text Available Gossip protocols aim at arriving, by means of point-to-point or group communications, at a situation in which all the agents know each other's secrets. We consider distributed gossip protocols which are expressed by means of epistemic logic. We provide an operational semantics of such protocols and set up an appropriate framework to argue about their correctness. Then we analyze specific protocols for complete graphs and for directed rings.

Verification of communication protocols in web services model-checking service compositions

CERN Document Server

Tari, Zahir; Mukherjee, Anshuman

2014-01-01

Gathers recent advancements in the field of self-organizing wireless sensor networks and provides readers with the essential, state-of-the-art information about sensor networking. In the near future, wireless sensor networks will become an integral part of our day-to-day life. To solve different sensor networking related issues, researchers have put a great deal of effort into coming up with innovative ideas. Verification of Communication Protocols in Web Services: Model-Checking Service Compositions gathers recent advancements in the field of self-organizing wireless sensor networks and provides readers with integral information about sensor networking. It introduces current technological trends, particularly in node organization, and provides implementation details of each networking type to help readers set up sensor networks in their related job fields. In addition, it identifies the limitations of current technologies, as well as future research directions.

Proposed Fuzzy-NN Algorithm with LoRaCommunication Protocol for Clustered Irrigation Systems

Directory of Open Access Journals (Sweden)

Sotirios Kontogiannis

2017-11-01

Full Text Available Modern irrigation systems utilize sensors and actuators, interconnected together as a single entity. In such entities, A.I. algorithms are implemented, which are responsible for the irrigation process. In this paper, the authors present an irrigation Open Watering System (OWS architecture that spatially clusters the irrigation process into autonomous irrigation sections. Authors’ OWS implementation includes a Neuro-Fuzzy decision algorithm called FITRA, which originates from the Greek word for seed. In this paper, the FITRA algorithm is described in detail, as are experimentation results that indicate significant water conservations from the use of the FITRA algorithm. Furthermore, the authors propose a new communication protocol over LoRa radio as an alternative low-energy and long-range OWS clusters communication mechanism. The experimental scenarios confirm that the FITRA algorithm provides more efficient irrigation on clustered areas than existing non-clustered, time scheduled or threshold adaptive algorithms. This is due to the FITRA algorithm’s frequent monitoring of environmental conditions, fuzzy and neural network adaptation as well as adherence to past irrigation preferences.

Network protocol changes can improve DisCom WAN performance : evaluating TCP modifications and SCTP in the ASC tri-lab environment.

Energy Technology Data Exchange (ETDEWEB)

Tolendino, Lawrence F.; Hu, Tan Chang

2005-06-01

The Advanced Simulation and Computing (ASC) Distance Computing (DisCom) Wide Area Network (WAN) is a high performance, long distance network environment that is based on the ubiquitous TCP/IP protocol set. However, the Transmission Control Protocol (TCP) and the algorithms that govern its operation were defined almost two decades ago for a network environment vastly different from the DisCom WAN. In this paper we explore and evaluate possible modifications to TCP that purport to improve TCP performance in environments like the DisCom WAN. We also examine a much newer protocol, SCTP (Stream Control Transmission Protocol) that claims to provide reliable network transport while also implementing multi-streaming, multi-homing capabilities that are appealing in the DisCom high performance network environment. We provide performance comparisons and recommendations for continued development that will lead to network communications protocol implementations capable of supporting the coming ASC Petaflop computing environments.

Reliability of IP Tunnels in Military Networks

Directory of Open Access Journals (Sweden)

Pólkowski Marcin

2016-10-01

Full Text Available The military networks, contrary to commercial ones, require standards which provide the highest level of security and reliability. The process to assuring redundancy of the main connections through applying various protocols and transmission media causes problem with time needed to re-establish virtual tunnels between different locations in case of damaged link. This article compares reliability of different IP (Internet Protocol tunnels, which were implemented on military network devices.

Reliable Multihop Broadcast Protocol with a Low-Overhead Link Quality Assessment for ITS Based on VANETs in Highway Scenarios

Directory of Open Access Journals (Sweden)

Alejandro Galaviz-Mosqueda

2014-01-01

Full Text Available Vehicular ad hoc networks (VANETs have been identified as a key technology to enable intelligent transport systems (ITS, which are aimed to radically improve the safety, comfort, and greenness of the vehicles in the road. However, in order to fully exploit VANETs potential, several issues must be addressed. Because of the high dynamic of VANETs and the impairments in the wireless channel, one key issue arising when working with VANETs is the multihop dissemination of broadcast packets for safety and infotainment applications. In this paper a reliable low-overhead multihop broadcast (RLMB protocol is proposed to address the well-known broadcast storm problem. The proposed RLMB takes advantage of the hello messages exchanged between the vehicles and it processes such information to intelligently select a relay set and reduce the redundant broadcast. Additionally, to reduce the hello messages rate dependency, RLMB uses a point-to-zone link evaluation approach. RLMB performance is compared with one of the leading multihop broadcast protocols existing to date. Performance metrics show that our RLMB solution outperforms the leading protocol in terms of important metrics such as packet dissemination ratio, overhead, and delay.

Reliable and Efficient Access for Alarm-initiated and Regular M2M Traffic in IEEE 802.11ah Systems

DEFF Research Database (Denmark)

Madueño, Germán Corrales; Stefanovic, Cedomir; Popovski, Petar

2016-01-01

IEEE 802.11ah is a novel WiFi-based protocol, aiming to provide an access solution for the machine-to-machine (M2M) communications. In this paper, we propose an adaptive access mechanism that can be seamlessly incorporated into IEEE 802.11ah protocol operation and that supports all potential M2M...... reporting regimes, which are periodic, on-demand and alarm reporting. The proposed access method is based a periodically re- occurring pool of time slots, whose size is proactively determined on the basis of the reporting activity in the cell. We show that it is possible to both efficiently and reliably...

Interoperative fundus image and report sharing in compliance with integrating the healthcare enterprise conformance and web access to digital imaging and communication in medicine persistent object protocol.

Science.gov (United States)

Wu, Hui-Qun; Lv, Zheng-Min; Geng, Xing-Yun; Jiang, Kui; Tang, Le-Min; Zhou, Guo-Min; Dong, Jian-Cheng

2013-01-01

To address issues in interoperability between different fundus image systems, we proposed a web eye-picture archiving and communication system (PACS) framework in conformance with digital imaging and communication in medicine (DICOM) and health level 7 (HL7) protocol to realize fundus images and reports sharing and communication through internet. Firstly, a telemedicine-based eye care work flow was established based on integrating the healthcare enterprise (IHE) Eye Care technical framework. Then, a browser/server architecture eye-PACS system was established in conformance with the web access to DICOM persistent object (WADO) protocol, which contains three tiers. In any client system installed with web browser, clinicians could log in the eye-PACS to observe fundus images and reports. Multipurpose internet mail extensions (MIME) type of a structured report is saved as pdf/html with reference link to relevant fundus image using the WADO syntax could provide enough information for clinicians. Some functions provided by open-source Oviyam could be used to query, zoom, move, measure, view DICOM fundus images. Such web eye-PACS in compliance to WADO protocol could be used to store and communicate fundus images and reports, therefore is of great significance for teleophthalmology.

A Protocol for Advanced Psychometric Assessment of Surveys

Science.gov (United States)

Squires, Janet E.; Hayduk, Leslie; Hutchinson, Alison M.; Cranley, Lisa A.; Gierl, Mark; Cummings, Greta G.; Norton, Peter G.; Estabrooks, Carole A.

2013-01-01

Background and Purpose. In this paper, we present a protocol for advanced psychometric assessments of surveys based on the Standards for Educational and Psychological Testing. We use the Alberta Context Tool (ACT) as an exemplar survey to which this protocol can be applied. Methods. Data mapping, acceptability, reliability, and validity are addressed. Acceptability is assessed with missing data frequencies and the time required to complete the survey. Reliability is assessed with internal consistency coefficients and information functions. A unitary approach to validity consisting of accumulating evidence based on instrument content, response processes, internal structure, and relations to other variables is taken. We also address assessing performance of survey data when aggregated to higher levels (e.g., nursing unit). Discussion. In this paper we present a protocol for advanced psychometric assessment of survey data using the Alberta Context Tool (ACT) as an exemplar survey; application of the protocol to the ACT survey is underway. Psychometric assessment of any survey is essential to obtaining reliable and valid research findings. This protocol can be adapted for use with any nursing survey. PMID:23401759

Compact wireless control network protocol with fast path switching

Directory of Open Access Journals (Sweden)

Yasutaka Kawamoto

2017-08-01

Full Text Available Sensor network protocol stacks require the addition or adjustment of functions based on customer requirements. Sensor network protocols that require low delay and low packet error rate (PER, such as wireless control networks, often adopt time division multiple access (TDMA. However, it is difficult to add or adjust functions in protocol stacks that use TDMA methods. Therefore, to add or adjust functions easily, we propose NES-SOURCE, a compact wireless control network protocol with a fast path-switching function. NES-SOURCE is implemented using carrier sense multiple access/collision avoidance (CSMA/CA rather than TDMA. Wireless control networks that use TDMA prevent communication failure by duplicating the communication path. If CSMA/CA networks use duplicate paths, collisions occur frequently, and communication will fail. NES-SOURCE switches paths quickly when communication fails, which reduces the effect of communication failures. Since NES-SOURCE is implemented using CSMA/CA rather than TDMA, the implementation scale is less than one-half that of existing network stacks. Furthermore, since NES-SOURCE’s code complexity is low, functions can be added or adjusted easily and quickly. Communication failures occur owing to changes in the communication environment and collisions. Experimental results demonstrate that the proposed NES-SOURCE’s path-switching function reduces the amount of communication failures when the communication environment changes owing to human movement and others. Furthermore, we clarify the relationships among the probability of a changing communication environment, the collision occurrence rate, and the PER of NES-SOURCE.

A PROPOSED MAPPING ARCHITECTURE BETWEEN IAX AND JINGLE PROTOCOLS

OpenAIRE

Hadeel Saleh Haj Aliwi; Putra Sumari

2016-01-01

Nowadays, multimedia communication has improved rapidly to allow people to communicate via the Internet. However, Internet users cannot communicate with each other unless they use the same chatting applications since each chatting application uses a certain signaling protocol to make the media call. The mapping architecture is a very critical issue since it solves the communication problems between any two protocols, as well as it enables people around the world to make a voice/video call eve...

Protocol to Exploit Waiting Resources for UASNs

Directory of Open Access Journals (Sweden)

Li-Ling Hung

2016-03-01

Full Text Available The transmission speed of acoustic waves in water is much slower than that of radio waves in terrestrial wireless sensor networks. Thus, the propagation delay in underwater acoustic sensor networks (UASN is much greater. Longer propagation delay leads to complicated communication and collision problems. To solve collision problems, some studies have proposed waiting mechanisms; however, long waiting mechanisms result in low bandwidth utilization. To improve throughput, this study proposes a slotted medium access control protocol to enhance bandwidth utilization in UASNs. The proposed mechanism increases communication by exploiting temporal and spatial resources that are typically idle in order to protect communication against interference. By reducing wait time, network performance and energy consumption can be improved. A performance evaluation demonstrates that when the data packets are large or sensor deployment is dense, the energy consumption of proposed protocol is less than that of existing protocols as well as the throughput is higher than that of existing protocols.

Adaptive Beaconing in Mobility Aware Clustering Based MAC Protocol for Safety Message Dissemination in VANET

Directory of Open Access Journals (Sweden)

Nishu Gupta

2017-01-01

Full Text Available Majority of research contributions in wireless access in vehicular environment (WAVE/IEEE 802.11p standard focus on life critical safety-related applications. These applications require regular status update of vehicle’s position referred to as beaconing. Periodic beaconing in vehicle to vehicle communication leads to severe network congestion in the communication channel. The condition worsens under high vehicular density where it impacts reliability and upper bound latency of safety messages. In this paper, WAVE compliant enhancement to the existing IEEE 802.11p protocol is presented which targets prioritized delivery of safety messages while simultaneously provisioning the dissemination of nonsafety messages. Proposed scheme relies on dynamic generation of beacons to mitigate channel congestion and inefficient bandwidth utilization by reducing transmission frequency of beacons. Through the use of clustering mechanism, different beaconing frequencies and different data transmission rates are assigned to prioritize vehicular mobility. Through extensive simulation results, the performance of the proposed approach is evaluated in terms of a wide range of quality of service (QoS parameters for two different transmission ranges. Results show that the proposed protocol provides significant enhancement and stability of the clustered topology in vehicular ad hoc network over existing standard and other protocols with similar applications.

Implementation of an Ethernet-Based Communication Channel for the Patmos Processor

DEFF Research Database (Denmark)

Pezzarossa, Luca; Kenn Toft, Jakob; Lønbæk, Jesper

The Patmos processor, which is used as the intellectual property of the T-CREST platform, is only equipped with a RS-232 serial port for communication with the outside world. The serial port is a minimal input/output device with a limited speed and without native networking features. An Ethernet 10....../100BASE-T IEEE 802.3 based communication channel is a reliable and high speed communication interface (10/100 Mbits/s) that also supports networking. This technical report presents an implementation of an Ethernet-based communication channel for the Patmos processor, targeting the Terasic DE2......-115 development board. We have designed the hardware to interface the EthMac Ethernet controller from OpenCores to Patmos and to the physical chip of the development board, and we have implemented a software library to drive the controller and to support some essential protocols. The design was implemented...

Energy Efficient Medium Access Control Protocol for Clustered Wireless Sensor Networks with Adaptive Cross-Layer Scheduling.

Science.gov (United States)

Sefuba, Maria; Walingo, Tom; Takawira, Fambirai

2015-09-18

This paper presents an Energy Efficient Medium Access Control (MAC) protocol for clustered wireless sensor networks that aims to improve energy efficiency and delay performance. The proposed protocol employs an adaptive cross-layer intra-cluster scheduling and an inter-cluster relay selection diversity. The scheduling is based on available data packets and remaining energy level of the source node (SN). This helps to minimize idle listening on nodes without data to transmit as well as reducing control packet overhead. The relay selection diversity is carried out between clusters, by the cluster head (CH), and the base station (BS). The diversity helps to improve network reliability and prolong the network lifetime. Relay selection is determined based on the communication distance, the remaining energy and the channel quality indicator (CQI) for the relay cluster head (RCH). An analytical framework for energy consumption and transmission delay for the proposed MAC protocol is presented in this work. The performance of the proposed MAC protocol is evaluated based on transmission delay, energy consumption, and network lifetime. The results obtained indicate that the proposed MAC protocol provides improved performance than traditional cluster based MAC protocols.

An Evaluation of Protocols for UAV Science Applications

Science.gov (United States)

Ivancic, William D.; Stewart, David E.; Sullivan, Donald V.; Finch, Patrick E.

2012-01-01

This paper identifies data transport needs for current and future science payloads deployed on the NASA Global Hawk Unmanned Aeronautical Vehicle (UAV). The NASA Global Hawk communication system and operational constrains are presented. The Genesis and Rapid Intensification Processes (GRIP) mission is used to provide the baseline communication requirements as a variety of payloads were utilized in this mission. User needs and desires are addressed. Protocols are matched to the payload needs and an evaluation of various techniques and tradeoffs are presented. Such techniques include utilization rate-base selective negative acknowledgement protocols and possible use of protocol enhancing proxies. Tradeoffs of communication architectures that address ease-of-use and security considerations are also presented.

Standardized communication protocol for BAS (IEIEJ/p); BAS hyojun interface shiyo (IEIEJ/p)

Energy Technology Data Exchange (ETDEWEB)

Toyoda, T. [Hitachi Building System Co. Ltd., Tokyo (Japan)

2000-10-05

For the BEMS user, to construct his BEMS tinder the multiple vendors environment is very beneficial because he could choice the most appropriate vendor among many vendors about every subsystem for the view point of technique and cost at any time. The effective tool which makes the BEMS tinder the multiple environment possible is the BACnet protocol which had developed and been standardized by ANSI/ASHRAE of U.S.. Institute of Electrical Installation Engineers-of Japan (IEIEJ) offers IEIEJ/p based on BACnet as IEIEJ's standard which is added the function of autonomous decentralized control to enhance the BEMS reliability to fit the Japanese multiple vendors environment, In this paper I present the outline of it's specification and feature of IEIEJ/p. (author)

Using standardized video cases for assessment of medical communication skills: reliability of an objective structured video examination by computer

NARCIS (Netherlands)

Hulsman, R. L.; Mollema, E. D.; Oort, F. J.; Hoos, A. M.; de Haes, J. C. J. M.

2006-01-01

OBJECTIVE: Using standardized video cases in a computerized objective structured video examination (OSVE) aims to measure cognitive scripts underlying overt communication behavior by questions on knowledge, understanding and performance. In this study the reliability of the OSVE assessment is

Real-time communication protocols: an overview

NARCIS (Netherlands)

Hanssen, F.T.Y.; Jansen, P.G.

2003-01-01

This paper describes several existing data link layer protocols that provide real-time capabilities on wired networks, focusing on token-ring and Carrier Sense Multiple Access based networks. Existing modifications to provide better real-time capabilities and performance are also described. Finally

Message Collision Avoidance Protocols for Detecting Stray Nodes in a Scuba Diving Group Using Ultrasonic Multi-Hop Message Communication

Directory of Open Access Journals (Sweden)

Shinya Kaido

2017-12-01

Full Text Available Recent years have seen a growing interest in underwater communication and some progress has been made in this area. However, underwater communication is still immature compared with terrestrial communication. A prime reason for this is that the underwater environment is intrinsically not suitable for propagation of electric waves. Instead, ultrasonic waves are mainly used for underwater communication. Since ultrasonic waves cannot provide sufficient communication speed or capacity, they cannot use existing network technologies, which assume use of radio waves. In particular, communication in shallow water is still an uncharted territory. Few communication technologies are employed in environments where people enjoy scuba diving. This paper addresses problems faced by recreational scuba divers. It proposes constructing an ad hoc mesh-shaped network between divers within a group and use ultrasonic waves as transmission media in order to enable the detection of a stray diver. It also proposes a communication protocol in which messages are relayed in multiple hops, and a message collision avoidance method, which is intended to reduce the rate of packet loss caused by message propagation delay. We have implemented the proposed methods in a network simulator, and compared them with an existing communication method that has no message collision avoidance function, in terms of the packet loss rate, the stray driver detection rate, and the rate of the ability to communicate in multiple hops.

Two-party quantum key agreement protocols under collective noise channel

Science.gov (United States)

Gao, Hao; Chen, Xiao-Guang; Qian, Song-Rong

2018-06-01

Recently, quantum communication has become a very popular research field. The quantum key agreement (QKA) plays an important role in the field of quantum communication, based on its unconditional security in terms of theory. Among all kinds of QKA protocols, QKA protocols resisting collective noise are widely being studied. In this paper, we propose improved two-party QKA protocols resisting collective noise and present a feasible plan for information reconciliation. Our protocols' qubit efficiency has achieved 26.67%, which is the best among all the two-party QKA protocols against collective noise, thus showing that our protocol can improve the transmission efficiency of quantum key agreement.

Adaptation of a MR imaging protocol into a real-time clinical biometric ultrasound protocol for persons with spinal cord injury at risk for deep tissue injury: A reliability study.

Science.gov (United States)

Swaine, Jillian M; Moe, Andrew; Breidahl, William; Bader, Daniel L; Oomens, Cees W J; Lester, Leanne; O'Loughlin, Edmond; Santamaria, Nick; Stacey, Michael C

2018-02-01

High strain in soft tissues that overly bony prominences are considered a risk factor for pressure ulcers (PUs) following spinal cord impairment (SCI) and have been computed using Finite Element methods (FEM). The aim of this study was to translate a MRI protocol into ultrasound (US) and determine between-operator reliability of expert sonographers measuring diameter of the inferior curvature of the ischial tuberosity (IT) and the thickness of the overlying soft tissue layers on able-bodied (AB) and SCI using real-time ultrasound. Part 1: Fourteen AB participants with a mean age of 36.7 ± 12.09 years with 7 males and 7 females had their 3 soft tissue layers in loaded and unloaded sitting measured independently by 2 sonographers: tendon/muscle, skin/fat and total soft tissue and the diameter of the IT in its short and long axis. Part 2: Nineteen participants with SCI were screened, three were excluded due to abnormal skin signs, and eight participants (42%) were excluded for abnormal US signs with normal skin. Eight SCI participants with a mean age of 31.6 ± 13.6 years and all male with 4 paraplegics and 4 tetraplegics were measured by the same sonographers for skin, fat, tendon, muscle and total. Skin/fat and tendon/muscle were computed. AB between-operator reliability was good (ICC = 0.81-0.90) for 3 soft tissues layers in unloaded and loaded sitting and poor for both IT short and long axis (ICC = -0.028 and -0.01). SCI between-operator reliability was good in unloaded and loaded for total, muscle, fat, skin/fat, tendon/muscle (ICC = 0.75-0.97) and poor for tendon (ICC = 0.26 unloaded and ICC = -0.71 loaded) and skin (ICC = 0.37 unloaded and ICC = 0.10). A MRI protocol was successfully adapted for a reliable 3 soft tissue layer model and could be used in a 2-D FEM model designed to estimate soft tissue strain as a novel risk factor for the development of a PU. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

An Indication of Reliability of the Two-Level Approach of the AWIN Welfare Assessment Protocol for Horses

Directory of Open Access Journals (Sweden)

Irena Czycholl

2018-01-01

Full Text Available To enhance feasibility, the Animal Welfare Indicators (AWIN assessment protocol for horses consists of two levels: the first is a visual inspection of a sample of horses performed from a distance, the second a close-up inspection of all horses. The aim was to analyse whether information would be lost if only the first level were performed. In this study, 112 first and 112 second level assessments carried out on a subsequent day by one observer were compared by calculating the Spearman’s Rank Correlation Coefficient (RS, Intraclass Correlation Coefficients (ICC, Smallest Detectable Changes (SDC and Limits of Agreements (LoA. Most indicators demonstrated sufficient reliability between the two levels. Exceptions were the Horse Grimace Scale, the Avoidance Distance Test and the Voluntary Human Approach Test (e.g., Voluntary Human Approach Test: RS: 0.38, ICC: 0.38, SDC: 0.21, LoA: −0.25–0.17, which could, however, be also interpreted as a lack of test-retest reliability. Further disagreement was found for the indicator consistency of manure (RS: 0.31, ICC: 0.38, SDC: 0.36, LoA: −0.38–0.36. For these indicators, an adaptation of the first level would be beneficial. Overall, in this study, the division into two levels was reliable and might therewith have the potential to enhance feasibility in other welfare assessment schemes.

PC communication

International Nuclear Information System (INIS)

Oh, Jae Cheol

1992-03-01

This text book is comprised of five charters, which is about PC communication for beginners who need to learn manners and how to use Ketel and PC serve. So it introduces first, conception of PC and precautions on using PC communication, second, preparation for PC communication with Modem, its program, install, kinds of protocol and how to use protocol, third directions of emulator of PC communication and super session, fourth, instruction of Ketel with join and access, basic command of Ketel, list of Ketel's menu, Ketel editor, service guide, directions of News service, Stock and bond service business and economic figures, exchange rate and interest rate, tax culture and leisure, Ketel BBS service and posting. The last part has a instruction of PC-serve about join, basic command of PC-serve, service guide and practical guideline.

PC communication

Energy Technology Data Exchange (ETDEWEB)

Oh, Jae Cheol

1992-03-15

This text book is comprised of five charters, which is about PC communication for beginners who need to learn manners and how to use Ketel and PC serve. So it introduces first, conception of PC and precautions on using PC communication, second, preparation for PC communication with Modem, its program, install, kinds of protocol and how to use protocol, third directions of emulator of PC communication and super session, fourth, instruction of Ketel with join and access, basic command of Ketel, list of Ketel's menu, Ketel editor, service guide, directions of News service, Stock and bond service business and economic figures, exchange rate and interest rate, tax culture and leisure, Ketel BBS service and posting. The last part has a instruction of PC-serve about join, basic command of PC-serve, service guide and practical guideline.

In silico toxicology protocols.

Science.gov (United States)

Myatt, Glenn J; Ahlberg, Ernst; Akahori, Yumi; Allen, David; Amberg, Alexander; Anger, Lennart T; Aptula, Aynur; Auerbach, Scott; Beilke, Lisa; Bellion, Phillip; Benigni, Romualdo; Bercu, Joel; Booth, Ewan D; Bower, Dave; Brigo, Alessandro; Burden, Natalie; Cammerer, Zoryana; Cronin, Mark T D; Cross, Kevin P; Custer, Laura; Dettwiler, Magdalena; Dobo, Krista; Ford, Kevin A; Fortin, Marie C; Gad-McDonald, Samantha E; Gellatly, Nichola; Gervais, Véronique; Glover, Kyle P; Glowienke, Susanne; Van Gompel, Jacky; Gutsell, Steve; Hardy, Barry; Harvey, James S; Hillegass, Jedd; Honma, Masamitsu; Hsieh, Jui-Hua; Hsu, Chia-Wen; Hughes, Kathy; Johnson, Candice; Jolly, Robert; Jones, David; Kemper, Ray; Kenyon, Michelle O; Kim, Marlene T; Kruhlak, Naomi L; Kulkarni, Sunil A; Kümmerer, Klaus; Leavitt, Penny; Majer, Bernhard; Masten, Scott; Miller, Scott; Moser, Janet; Mumtaz, Moiz; Muster, Wolfgang; Neilson, Louise; Oprea, Tudor I; Patlewicz, Grace; Paulino, Alexandre; Lo Piparo, Elena; Powley, Mark; Quigley, Donald P; Reddy, M Vijayaraj; Richarz, Andrea-Nicole; Ruiz, Patricia; Schilter, Benoit; Serafimova, Rositsa; Simpson, Wendy; Stavitskaya, Lidiya; Stidl, Reinhard; Suarez-Rodriguez, Diana; Szabo, David T; Teasdale, Andrew; Trejo-Martin, Alejandra; Valentin, Jean-Pierre; Vuorinen, Anna; Wall, Brian A; Watts, Pete; White, Angela T; Wichard, Joerg; Witt, Kristine L; Woolley, Adam; Woolley, David; Zwickl, Craig; Hasselgren, Catrin

2018-04-17

The present publication surveys several applications of in silico (i.e., computational) toxicology approaches across different industries and institutions. It highlights the need to develop standardized protocols when conducting toxicity-related predictions. This contribution articulates the information needed for protocols to support in silico predictions for major toxicological endpoints of concern (e.g., genetic toxicity, carcinogenicity, acute toxicity, reproductive toxicity, developmental toxicity) across several industries and regulatory bodies. Such novel in silico toxicology (IST) protocols, when fully developed and implemented, will ensure in silico toxicological assessments are performed and evaluated in a consistent, reproducible, and well-documented manner across industries and regulatory bodies to support wider uptake and acceptance of the approaches. The development of IST protocols is an initiative developed through a collaboration among an international consortium to reflect the state-of-the-art in in silico toxicology for hazard identification and characterization. A general outline for describing the development of such protocols is included and it is based on in silico predictions and/or available experimental data for a defined series of relevant toxicological effects or mechanisms. The publication presents a novel approach for determining the reliability of in silico predictions alongside experimental data. In addition, we discuss how to determine the level of confidence in the assessment based on the relevance and reliability of the information. Copyright © 2018. Published by Elsevier Inc.

Using OAI and other light-weight protocols to facilitate scholarly communication

CERN Multimedia

CERN. Geneva

2005-01-01

This presentation describes how we share and harvest sets of various OAI metadata, repurpose it through the Ockham Library Network, and demonstrate an alternative to traditional scholarly communication. The Ockham Library Network is a sponsored National Science Foundation Digital Library grant with co-PI's at Emory University, Virginia Tech, Oregon State University, and the University of Notre Dame. One of the purposes of Ockham is to exploit modular, light-weight protocols (such as OAI-PMH and SRW/U) into systems for learning, teaching, and scholarship. To date we have implemented a number of such services: * Ockham Digital Library Services Registry - A distributed directory of digital library services, collections, and agents. The contents of the Registry are described using the same XML schema articulated by the Information Environment Service Registry (IESR), and the records are shared among participating institutions on a peer-to-peer network utilizing OAI to propagate registry records amongst the distri...

Rating parent-child interactions: joint engagement, communication dynamics, and shared topics in autism, Down syndrome, and typical development.

Science.gov (United States)

Adamson, Lauren B; Bakeman, Roger; Deckner, Deborah F; Nelson, P Brooke

2012-12-01

A battery of 17 rating items were applied to video records of typically-developing toddlers and young children with autism and Down syndrome interacting with their parents during the Communication Play Protocol. This battery provided a reliable and broad view of the joint engagement triad of child, partner, and shared topic. Ratings of the child's joint engagement correlated very strongly with state coding of joint engagement and replicated the finding that coordinated joint engagement was less likely in children with autism. Ratings of other child actions, of parent contributions, and of shared topics and communicative dynamics also documented pervasive variations related to diagnosis, language facility, and communicative context.

Relay Selections for Security and Reliability in Mobile Communication Networks over Nakagami-m Fading Channels

Directory of Open Access Journals (Sweden)

Hongji Huang

2017-01-01

Full Text Available This paper studies the relay selection schemes in mobile communication system over Nakagami-m channel. To make efficient use of licensed spectrum, both single relay selection (SRS scheme and multirelays selection (MRS scheme over the Nakagami-m channel are proposed. Also, the intercept probability (IP and outage probability (OP of the proposed SRS and MRS for the communication links depending on realistic spectrum sensing are derived. Furthermore, this paper assesses the manifestation of conventional direct transmission scheme to compare with the proposed SRS and MRS ones based on the Nakagami-m channel, and the security-reliability trade-off (SRT performance of the proposed schemes and the conventional schemes is well investigated. Additionally, the SRT of the proposed SRS and MRS schemes is demonstrated better than that of direct transmission scheme over the Nakagami-m channel, which can protect the communication transmissions against eavesdropping attacks. Additionally, simulation results show that our proposed relay selection schemes achieve better SRT performance than that of conventional direct transmission over the Nakagami-m channel.

Reliability Engineering

CERN Document Server

Lazzaroni, Massimo

2012-01-01

This book gives a practical guide for designers and users in Information and Communication Technology context. In particular, in the first Section, the definition of the fundamental terms according to the international standards are given. Then, some theoretical concepts and reliability models are presented in Chapters 2 and 3: the aim is to evaluate performance for components and systems and reliability growth. Chapter 4, by introducing the laboratory tests, puts in evidence the reliability concept from the experimental point of view. In ICT context, the failure rate for a given system can be

Programmable synchronous communications module

International Nuclear Information System (INIS)

Horelick, D.

1979-10-01

The functional characteristics of a programmable, synchronous serial communications CAMAC module with buffering in block format are described. Both bit and byte oriented protocols can be handled in full duplex depending on the program implemented. The main elements of the module are a Signetics 2652 Multi-Protocol Communications Controller, a Zilog Z-808 8 bit microprocessor with PROM and RAM, and FIFOs for buffering

Analysis of the differential-phase-shift-keying protocol in the quantum-key-distribution system

International Nuclear Information System (INIS)

Rong-Zhen, Jiao; Chen-Xu, Feng; Hai-Qiang, Ma

2009-01-01

The analysis is based on the error rate and the secure communication rate as functions of distance for three quantum-key-distribution (QKD) protocols: the Bennett–Brassard 1984, the Bennett–Brassard–Mermin 1992, and the coherent differential-phase-shift keying (DPSK) protocols. We consider the secure communication rate of the DPSK protocol against an arbitrary individual attack, including the most commonly considered intercept-resend and photon-number splitting attacks, and concluded that the simple and efficient differential-phase-shift-keying protocol allows for more than 200 km of secure communication distance with high communication rates. (general)

The Security Analysis of Two-Step Quantum Direct Communication Protocol in Collective-Rotation Noise Channel

International Nuclear Information System (INIS)

Li Jian; Sun Feng-Qi; Pan Ze-Shi; Nie Jin-Rui; Chen Yan-Hua; Yuan Kai-Guo

2015-01-01

To analyze the security of two-step quantum direct communication protocol (QDCP) by using Einstein–Podolsky–Rosen pair proposed by Deng et al. [Phys. Rev. A 68 (2003) 042317] in collective-rotation noise channel, an excellent model of noise analysis is proposed. In the security analysis, the method of the entropy theory is introduced, and is compared with QDCP, an error rate point Q 0 (M : (Q 0 , 1.0)) is given. In different noise levels, if Eve wants to obtain the same amount of information, the error rate Q is distinguishable. The larger the noise level ϵ is, the larger the error rate Q is. When the noise level ϵ is lower than 11%, the high error rate is 0.153 without eavesdropping. Lastly, the security of the proposed protocol is discussed. It turns out that the quantum channel will be safe when Q < 0.153. Similarly, if error rate Q > 0.153 = Q 0 , eavesdropping information I > 1, which means that there exist eavesdroppers in the quantum channel, and the quantum channel will not be safe anymore. (paper)

High speed serial communications for control systems

International Nuclear Information System (INIS)

Mathieson, D.; Kalbfleisch, C.; Hunt, S.; Low, K.

1993-01-01

The Superconducting Super Collider Laboratory is a complex of accelerators being built in Ellis County, Texas. The SSCL control system consists of front-end processors and their associated control points remotely distributed from the Central and Regional control rooms. Control messages passing between these locations require timely (deterministic) distribution. A prototype network consisting of point-to-point links utilizing commercial T1 (1.544 Mb/s) communication boards has been implemented. These dedicated communication links will replace networking services traditionally provided for by shared medium networks like Ethernet(IEEE 802.3) and FDDI(IEEE 802.5). A seamless migration will be achieved by using packet encapsulation based on PPP(Point-to-Point Protocol, RFC 1171). All other networking functions including routing and reliable delivery are still being handled by the usual internet services. A distributed control system that currently uses Ethernet for communication is being re-implemented using these point-to-point links. The authors report on throughput measurements, timing constraints and ease of transition of a point-to-point network

Communication Estimation for Hardware/Software Codesign

DEFF Research Database (Denmark)

Knudsen, Peter Voigt; Madsen, Jan

1998-01-01

This paper presents a general high level estimation model of communication throughput for the implementation of a given communication protocol. The model, which is part of a larger model that includes component price, software driver object code size and hardware driver area, is intended...... to be general enough to be able to capture the characteristics of a wide range of communication protocols and yet to be sufficiently detailed as to allow the designer or design tool to efficiently explore tradeoffs between throughput, bus widths, burst/non-burst transfers and data packing strategies. Thus...... it provides a basis for decision making with respect to communication protocols/components and communication driver design in the initial design space exploration phase of a co-synthesis process where a large number of possibilities must be examined and where fast estimators are therefore necessary. The fill...

Evaluation of mobile ad hoc network reliability using propagation-based link reliability model

International Nuclear Information System (INIS)

Padmavathy, N.; Chaturvedi, Sanjay K.

2013-01-01

A wireless mobile ad hoc network (MANET) is a collection of solely independent nodes (that can move randomly around the area of deployment) making the topology highly dynamic; nodes communicate with each other by forming a single hop/multi-hop network and maintain connectivity in decentralized manner. MANET is modelled using geometric random graphs rather than random graphs because the link existence in MANET is a function of the geometric distance between the nodes and the transmission range of the nodes. Among many factors that contribute to the MANET reliability, the reliability of these networks also depends on the robustness of the link between the mobile nodes of the network. Recently, the reliability of such networks has been evaluated for imperfect nodes (transceivers) with binary model of communication links based on the transmission range of the mobile nodes and the distance between them. However, in reality, the probability of successful communication decreases as the signal strength deteriorates due to noise, fading or interference effects even up to the nodes' transmission range. Hence, in this paper, using a propagation-based link reliability model rather than a binary-model with nodes following a known failure distribution to evaluate the network reliability (2TR m , ATR m and AoTR m ) of MANET through Monte Carlo Simulation is proposed. The method is illustrated with an application and some imperative results are also presented

An Enhanced LoRaWAN Security Protocol for Privacy Preservation in IoT with a Case Study on a Smart Factory-Enabled Parking System.

Science.gov (United States)

You, Ilsun; Kwon, Soonhyun; Choudhary, Gaurav; Sharma, Vishal; Seo, Jung Taek

2018-06-08

The Internet of Things (IoT) utilizes algorithms to facilitate intelligent applications across cities in the form of smart-urban projects. As the majority of devices in IoT are battery operated, their applications should be facilitated with a low-power communication setup. Such facility is possible through the Low-Power Wide-Area Network (LPWAN), but at a constrained bit rate. For long-range communication over LPWAN, several approaches and protocols are adopted. One such protocol is the Long-Range Wide Area Network (LoRaWAN), which is a media access layer protocol for long-range communication between the devices and the application servers via LPWAN gateways. However, LoRaWAN comes with fewer security features as a much-secured protocol consumes more battery because of the exorbitant computational overheads. The standard protocol fails to support end-to-end security and perfect forward secrecy while being vulnerable to the replay attack that makes LoRaWAN limited in supporting applications where security (especially end-to-end security) is important. Motivated by this, an enhanced LoRaWAN security protocol is proposed, which not only provides the basic functions of connectivity between the application server and the end device, but additionally averts these listed security issues. The proposed protocol is developed with two options, the Default Option (DO) and the Security-Enhanced Option (SEO). The protocol is validated through Burrows⁻Abadi⁻Needham (BAN) logic and the Automated Validation of Internet Security Protocols and Applications (AVISPA) tool. The proposed protocol is also analyzed for overheads through system-based and low-power device-based evaluations. Further, a case study on a smart factory-enabled parking system is considered for its practical application. The results, in terms of network latency with reliability fitting and signaling overheads, show paramount improvements and better performance for the proposed protocol compared with the two

An Enhanced LoRaWAN Security Protocol for Privacy Preservation in IoT with a Case Study on a Smart Factory-Enabled Parking System

Directory of Open Access Journals (Sweden)

Ilsun You

2018-06-01

Full Text Available The Internet of Things (IoT utilizes algorithms to facilitate intelligent applications across cities in the form of smart-urban projects. As the majority of devices in IoT are battery operated, their applications should be facilitated with a low-power communication setup. Such facility is possible through the Low-Power Wide-Area Network (LPWAN, but at a constrained bit rate. For long-range communication over LPWAN, several approaches and protocols are adopted. One such protocol is the Long-Range Wide Area Network (LoRaWAN, which is a media access layer protocol for long-range communication between the devices and the application servers via LPWAN gateways. However, LoRaWAN comes with fewer security features as a much-secured protocol consumes more battery because of the exorbitant computational overheads. The standard protocol fails to support end-to-end security and perfect forward secrecy while being vulnerable to the replay attack that makes LoRaWAN limited in supporting applications where security (especially end-to-end security is important. Motivated by this, an enhanced LoRaWAN security protocol is proposed, which not only provides the basic functions of connectivity between the application server and the end device, but additionally averts these listed security issues. The proposed protocol is developed with two options, the Default Option (DO and the Security-Enhanced Option (SEO. The protocol is validated through Burrows–Abadi–Needham (BAN logic and the Automated Validation of Internet Security Protocols and Applications (AVISPA tool. The proposed protocol is also analyzed for overheads through system-based and low-power device-based evaluations. Further, a case study on a smart factory-enabled parking system is considered for its practical application. The results, in terms of network latency with reliability fitting and signaling overheads, show paramount improvements and better performance for the proposed protocol compared with

On the network protocol performance evaluation for large scale communication system of nuclear plant

International Nuclear Information System (INIS)

Song, K. S.; Lee, T. H.; Kim, H. R.; Kim, D. H.; Ku, I. S.

1998-01-01

Computer technology has been dramatically advanced and it is now natural to apply digital network technology into nuclear plants. Communication architecture for nuclear plant defines the coordination of safety reactor control, balance of plant, subsystem utilities, and plant monitoring functions, and how they are connected and their user interface to guarantee plant performance and guarantee safety requirements. Therefore, to implement a digital network for control and monitoring systems of advanced nuclear plant needs systematic design and evaluation procedures because of responsive and hard real-time process characteristics of nuclear plant. In this paper, we evaluate several digital network protocols in terms of network delay, link failure effects to hard real-time requirements with full scale traffic

Faithful deterministic secure quantum communication and authentication protocol based on hyperentanglement against collective noise

International Nuclear Information System (INIS)

Chang Yan; Zhang Shi-Bin; Yan Li-Li; Han Gui-Hua

2015-01-01

Higher channel capacity and security are difficult to reach in a noisy channel. The loss of photons and the distortion of the qubit state are caused by noise. To solve these problems, in our study, a hyperentangled Bell state is used to design faithful deterministic secure quantum communication and authentication protocol over collective-rotation and collective-dephasing noisy channel, which doubles the channel capacity compared with using an ordinary Bell state as a carrier; a logical hyperentangled Bell state immune to collective-rotation and collective-dephasing noise is constructed. The secret message is divided into several parts to transmit, however the identity strings of Alice and Bob are reused. Unitary operations are not used. (paper)

Low-Power and Reliable Communications for UWB-Based Wireless Monitoring Sensor Networks in Underground Mine Tunnels

OpenAIRE

Abou El-Nasr, Mohamad; Shaban, Heba

2015-01-01

This paper investigates the bit-error-rate (BER) and maximum allowable data throughput (MADTh) performance of a novel low-power mismatched Rake receiver structure for ultra wideband (UWB) wireless monitoring sensor networks in underground mine tunnels. This receive node structure provides a promising solution for low-power and reliable communications in underground mine tunnels with more than 90% reduction in power consumption. The BER and MADTh of the proposed receive nodes are investigated ...

Engaging patients and families in communication across transitions of care: an integrative review protocol.

Science.gov (United States)

Bucknall, Tracey K; Hutchinson, Alison M; Botti, Mari; McTier, Lauren; Rawson, Helen; Hewitt, Nicky A; McMurray, Anne; Marshall, Andrea P; Gillespie, Brigid M; Chaboyer, Wendy

2016-07-01

To describe an integrative review protocol to analyse and synthesize peer-reviewed research evidence in relation to engagement of patients and their families in communication during transitions of care to, in and from acute care settings. Communication at transitions of care in acute care settings can be complex and challenging, with important information about patients not always clearly transferred between responsible healthcare providers. Involving patients and their families in communication during transitions of care may improve the transfer of clinical information and patient outcomes and prevent adverse events during hospitalization and following discharge. Recently, optimizing patient and family participation during care transitions has been acknowledged as central to the implementation of patient-centred care. Integrative review with potential for meta-analysis and application of framework synthesis. The review will evaluate and synthesize qualitative and quantitative research evidence identified through a systematic search. Primary studies will be selected according to inclusion criteria. Data collection, quality appraisal and analysis of the evidence will be conducted by at least two authors. Nine electronic databases (including CINAHL and Medline) will be searched. The search will be restricted to 10 years up to December 2013. Data analysis will include content and thematic analysis. The review will seek to identify all types of patient engagement activities employed during transitions of care communication. The review will identify enablers for and barriers to engagement for patients, families and health professionals. Key strategies and tools for improving patient engagement, clinical communication and promoting patient-centred care will be recommended based on findings. © 2016 The Authors. Journal of Advanced Nursing Published by John Wiley & Sons Ltd.

Evaluation of svr: a wireless sensor network routing protocol

International Nuclear Information System (INIS)

Baloch, J.; Khanzada, T.J.S.

2014-01-01

The advancement in technology has made it possible to create small in size, low cost sensor nodes. However, the small size and low cost of such nodes comesat at price that is, reduced processing power, low memory and significantly small battery energy storage. WSNs (Wireless Sensor Networks) are inherently ad hoc in nature and are assumed to work in the toughest terrain. The network lifetime plays a pivotal role in a wireless sensor network. A long network lifetime, could be achieved by either making significant changes in these low cost devices, which is not a feasible solution or by improving the means of communication throughout the network. The communication in such networks could be improved by employing energy efficient routing protocols, to route the data throughout the network. In this paper the SVR (Spatial Vector Routing) protocol is compared against the most common WSN routing protocols, and from the results it could be inferred that the SVR protocol out performs its counterparts. The protocol provides an energy efficient means of communication in the network. (author)

Power-Efficient Communication Protocol for Integrated WWAN and WLAN

Directory of Open Access Journals (Sweden)

Golmie Nada

2008-01-01

Full Text Available Abstract One of the most impending requirements to support a seamless communication environment in heterogeneous wireless networks comes from the limited power supply of small-size and low-cost mobile terminals as in stand-alone WLANs or cellular networks. Thus, it is a challenge to design new techniques so that mobile terminals are able to not only maintain their active connection as they move across different types of wireless networks, but also minimize their power consumption. There have been several efforts aimed at having mobile devices equipped with multiple interfaces connect optimally to the access network that minimizes their power consumption. However, a study of existing schemes for WLAN notes that in the idle state, a device with both a WLAN and a WWAN interface needs to keep both interfaces on in order to receive periodic beacon messages from the access point (AP: WLAN and downlink control information from the base station (WWAN, resulting in significant power consumption. Therefore, in this paper, we propose a power-efficient communication protocol (PCP that includes turning off the WLAN interface after it enters the idle state and using the paging channel of WWAN in order to wake up the WLAN interface when there is incoming long-lived multimedia data. This scheme is known to limit the power consumption, while at the same time, it makes use of the paging channel in cellular networks. Further, our proposed scheme is designed to avoid repeatedly turning on and off WLAN interfaces, that consumes a significant amount of power. We propose turning on the WLAN interface when the number of packets in the radio network controller (RNC's buffer reaches a certain threshold level. The tradeoffs between the power saving and the number of packets dropped at the buffer are investigated analytically through the study of an on/off traffic model. Simulation results for scenarios of interest are also provided.

Power-Efficient Communication Protocol for Integrated WWAN and WLAN

Directory of Open Access Journals (Sweden)

SuKyoung Lee

2008-01-01

Full Text Available One of the most impending requirements to support a seamless communication environment in heterogeneous wireless networks comes from the limited power supply of small-size and low-cost mobile terminals as in stand-alone WLANs or cellular networks. Thus, it is a challenge to design new techniques so that mobile terminals are able to not only maintain their active connection as they move across different types of wireless networks, but also minimize their power consumption. There have been several efforts aimed at having mobile devices equipped with multiple interfaces connect optimally to the access network that minimizes their power consumption. However, a study of existing schemes for WLAN notes that in the idle state, a device with both a WLAN and a WWAN interface needs to keep both interfaces on in order to receive periodic beacon messages from the access point (AP: WLAN and downlink control information from the base station (WWAN, resulting in significant power consumption. Therefore, in this paper, we propose a power-efficient communication protocol (PCP that includes turning off the WLAN interface after it enters the idle state and using the paging channel of WWAN in order to wake up the WLAN interface when there is incoming long-lived multimedia data. This scheme is known to limit the power consumption, while at the same time, it makes use of the paging channel in cellular networks. Further, our proposed scheme is designed to avoid repeatedly turning on and off WLAN interfaces, that consumes a significant amount of power. We propose turning on the WLAN interface when the number of packets in the radio network controller (RNC's buffer reaches a certain threshold level. The tradeoffs between the power saving and the number of packets dropped at the buffer are investigated analytically through the study of an on/off traffic model. Simulation results for scenarios of interest are also provided.

Efficient one-out-of-two quantum oblivious transfer based on four-coherent-state postselection protocol

International Nuclear Information System (INIS)

Chen, I-C; Hwang Tzonelih; Li C-M

2008-01-01

On the basis of the modified four-coherent-state post-selection quantum key distribution protocol (Namiki and Hirano 2006 Preprint quant-ph/0608144v1), two 1-out-of-2 quantum oblivious transfer (QOT 2 1 ) protocols are proposed. The first proposed protocol (called the receiver-based QOT 2 1 protocol) requires the coherent states to be prepared by the receiver, whereas the second protocol (called the sender-based QOT 2 1 protocol) allows the coherent states to be generated by the sender. The main advantages of the proposed protocols are that (i) no quantum bit commitment schemes and the assumption of quantum memory are needed; (ii) less communication cost between participants is required, i.e. the receiver-based QOT 2 1 protocol requires only one quantum communication and one classical communication and the sender-based QOT 2 1 protocol requires only one quantum communication between participants during protocol execution; and (iii) the utilization of quantum states is very efficient, wherein the receiver-based and the sender-based QOT 2 1 protocols use only two coherent pulses and one coherent pulse respectively for sending the sender's two messages

Common protocol aids consolidated communications

OpenAIRE

Center for Homeland Defense and Security

2010-01-01

Center for Homeland Defense and Security, OUT OF THE CLASSROOM Download the paper: Paper: Managing Information Across All Levels of the Coast Guard” While a student at CHDS, then-Coast Guardsman Chris Kluckhuhn was well aware of the different communications platforms...

A PROPOSED MAPPING ARCHITECTURE BETWEEN IAX AND JINGLE PROTOCOLS

Directory of Open Access Journals (Sweden)

Hadeel Saleh Haj Aliwi

2016-03-01

Full Text Available Nowadays, multimedia communication has improved rapidly to allow people to communicate via the Internet. However, Internet users cannot communicate with each other unless they use the same chatting applications since each chatting application uses a certain signaling protocol to make the media call. The mapping architecture is a very critical issue since it solves the communication problems between any two protocols, as well as it enables people around the world to make a voice/video call even if they use different chatting applications. Providing the interoperability between different signaling protocols and multimedia applications takes the advantages of more than one protocol. Many mapping architectures have been proposed to ease exchanging the media between at least two users without facing any difficulties such as SIP-Jingle, IAX-RSW, H.323-MGCP, etc. However, the design of any of the existing mapping architectures has some weaknesses related to larger delay, time consuming, and security matters. The only way to overcome these problems is to propose an efficient mapping architecture. This paper proposed a new mapping architecture between Inter-Asterisk eXchange Protocol and Jingle Protocol. The proposed mapping architecture consists of IAX domain (IAX client, IAX server, IAX-to-Jingle gateway, and Jingle domain (Jingle client, Jingle server, Jingle-to-IAX gateway. The tasks of the translation gateways are represented by the URI conversion, media capability exchange, translator of call setup and teardown signals, and real time media transmission.

Using generalizability theory to develop clinical assessment protocols.

Science.gov (United States)

Preuss, Richard A

2013-04-01

Clinical assessment protocols must produce data that are reliable, with a clinically attainable minimal detectable change (MDC). In a reliability study, generalizability theory has 2 advantages over classical test theory. These advantages provide information that allows assessment protocols to be adjusted to match individual patient profiles. First, generalizability theory allows the user to simultaneously consider multiple sources of measurement error variance (facets). Second, it allows the user to generalize the findings of the main study across the different study facets and to recalculate the reliability and MDC based on different combinations of facet conditions. In doing so, clinical assessment protocols can be chosen based on minimizing the number of measures that must be taken to achieve a realistic MDC, using repeated measures to minimize the MDC, or simply based on the combination that best allows the clinician to monitor an individual patient's progress over a specified period of time.

75 FR 43059 - Mandatory Reliability Standards for the Calculation of Available Transfer Capability, Capacity...

Science.gov (United States)

2010-07-23

... Standards for Business Practices and Communications Protocols for Public Utilities July 15, 2010. AGENCY... Practices and Communication Protocols for Public Utilities. Order No. 729-B Order on Rehearing and..., Order No. 729-A, 131 FERC ] 61,109 (2010). \\2\\ Standards for Business Practices and Communication...

Immunochemical protocols

National Research Council Canada - National Science Library

Pound, John D

1998-01-01

... easy and important refinements often are not published. This much anticipated 2nd edition of Immunochemzcal Protocols therefore aims to provide a user-friendly up-to-date handbook of reliable techniques selected to suit the needs of molecular biologists. It covers the full breadth of the relevant established immunochemical methods, from protein blotting and immunoa...

Quantitative Safety and Security Analysis from a Communication Perspective

Directory of Open Access Journals (Sweden)

Boris Malinowsky

2015-12-01

Full Text Available This paper introduces and exemplifies a trade-off analysis of safety and security properties in distributed systems. The aim is to support analysis for real-time communication and authentication building blocks in a wireless communication scenario. By embedding an authentication scheme into a real-time communication protocol for safety-critical scenarios, we can rely on the protocol’s individual safety and security properties. The resulting communication protocol satisfies selected safety and security properties for deployment in safety-critical use-case scenarios with security requirements. We look at handover situations in a IEEE 802.11 wireless setup between mobile nodes and access points. The trade-offs involve application-layer data goodput, probability of completed handovers, and effect on usable protocol slots, to quantify the impact of security from a lower-layer communication perspective on the communication protocols. The results are obtained using the network simulator ns-3.

Study Application of RADIUS Protocol on Ethernet

Institute of Scientific and Technical Information of China (English)

GUO Fang; YANG Huan-yu; LI Hong

2004-01-01

This paper presents how to apply the RADIUS (Remote Authentication Dial In User Service)protocol ,which is generally applied to dial-up network, to the authentication & charge of Broad Band accessing control system on Ethernet. It is provided that the Broad Band accessing control system included a self-designed communication protocol is used in communicating between an terminal user and Network Access Server .The interface module on the servers side and the Radius system is also given in this article.

Operating systems and network protocols for wireless sensor networks.

Science.gov (United States)

Dutta, Prabal; Dunkels, Adam

2012-01-13

Sensor network protocols exist to satisfy the communication needs of diverse applications, including data collection, event detection, target tracking and control. Network protocols to enable these services are constrained by the extreme resource scarcity of sensor nodes-including energy, computing, communications and storage-which must be carefully managed and multiplexed by the operating system. These challenges have led to new protocols and operating systems that are efficient in their energy consumption, careful in their computational needs and miserly in their memory footprints, all while discovering neighbours, forming networks, delivering data and correcting failures.

Collaborative communication protocols for wireless sensor networks

NARCIS (Netherlands)

Dulman, S.O.; van Hoesel, L.F.W.; Nieberg, T.; Havinga, Paul J.M.

In this document, the design of communication within a wireless sensor network is discussed. The resource limitations of such a network, especially in terms of energy, require an integrated approach for all (traditional) layers of communication. We present such an integrated, collaborative approach

Highly Reliable Power and Communication System for Essential Instruments under a Severe Accident of NPPs

Energy Technology Data Exchange (ETDEWEB)

Yoo, S. J.; Choi, B. H.; Jung, S. Y.; Rim, Chun T. [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2013-10-15

In this paper, three survivable strategies to overcome the problems listed above are proposed for the essential instruments under the severe accident of NPPs. First, wire/wireless multi power systems are adopted to the essential instruments for continuous power supply. Second, wire/wireless communication systems are proposed for reliable transmission of measuring information among instruments and operators. Third, a physical protection system such as a harness and a heat isolation box is introduced to ensure operable conditions for the proposed systems. In this paper, a highly reliable strategy, which consists of wire/wireless multi power and communication systems and physical protection system is proposed to ensure the survival of the essential instruments under harsh external conditions. The wire/wireless multi power and communication systems are designed to transfer power and data in spite of the failure of conventional wired systems. The physical protection system provides operable environments to the instruments. Therefore, the proposed system can be considered as a candidate of practical and urgent remedy for NPPs under the severe accident. After the Fukushima nuclear accident, survivability of essential instruments has been emphasized for immediate and accurate response. The essential instruments can measure environment conditions such as temperature, pressure, radioactivity and corium behavior inside nuclear power plants (NPPs) under a severe accident. Access to the inside of NPPs is restricted to human beings because of hazardous environment such as high radioactivity, high temperature and high pressure. Thus, monitoring the inside of NPPs is necessary for avoiding damage from the severe accident. Even though there were a number of instruments in Fukushima Daiichi NPP, they failed to obtain exact monitoring information. According to the details of the Fukushima nuclear accident, following problems can be counted as strong candidates of this instruments

Highly Reliable Power and Communication System for Essential Instruments under a Severe Accident of NPPs

International Nuclear Information System (INIS)

Yoo, S. J.; Choi, B. H.; Jung, S. Y.; Rim, Chun T.

2013-01-01

In this paper, three survivable strategies to overcome the problems listed above are proposed for the essential instruments under the severe accident of NPPs. First, wire/wireless multi power systems are adopted to the essential instruments for continuous power supply. Second, wire/wireless communication systems are proposed for reliable transmission of measuring information among instruments and operators. Third, a physical protection system such as a harness and a heat isolation box is introduced to ensure operable conditions for the proposed systems. In this paper, a highly reliable strategy, which consists of wire/wireless multi power and communication systems and physical protection system is proposed to ensure the survival of the essential instruments under harsh external conditions. The wire/wireless multi power and communication systems are designed to transfer power and data in spite of the failure of conventional wired systems. The physical protection system provides operable environments to the instruments. Therefore, the proposed system can be considered as a candidate of practical and urgent remedy for NPPs under the severe accident. After the Fukushima nuclear accident, survivability of essential instruments has been emphasized for immediate and accurate response. The essential instruments can measure environment conditions such as temperature, pressure, radioactivity and corium behavior inside nuclear power plants (NPPs) under a severe accident. Access to the inside of NPPs is restricted to human beings because of hazardous environment such as high radioactivity, high temperature and high pressure. Thus, monitoring the inside of NPPs is necessary for avoiding damage from the severe accident. Even though there were a number of instruments in Fukushima Daiichi NPP, they failed to obtain exact monitoring information. According to the details of the Fukushima nuclear accident, following problems can be counted as strong candidates of this instruments

Development of design methodology for communication network in nuclear power plants

International Nuclear Information System (INIS)

Kim, Dong Hoon; Seong, Seung Hwan; Jang Gwi Sook; Koo, In Soo; Lee Soon Sung.

1996-06-01

This report describe the design methodology of communication network (CN) in nuclear power plants (NPPs). The construction procedure for the NPP CN consists of 4 phases, in study and review phase, design concepts and goals are established through technical review, collection of background information and feasibility study. In design phase, all of design activities such as extraction of requirements, communication modelling, overall and detail architecture design are performed. Implementation and test phase includes the manufacturing, installation and testing of hardware and software. In operation phase, CN construction is finalized through the evaluation and correction during operation. The requirements of CN consist of general requirements such as function, structure, reliability, standardization and detail requirements related with protocol, media, error, performance and etc. CN design also should follow the safety-related requirements such as isolation, redundancy, reliability and verify these requirements. For the selection of each technical element form commercial CN, the evaluation and selection elements are extracted from reliability, performance, operating factors and the required-level which classified into essential, primary, preference, recommendation should be assigned to each element. This report will be used as a technical reference for the CN implementation in NPP. (author). 3 tabs., 5 figs., 25 refs

Reliability of the Star Excursion Balance Test and Two New Similar Protocols to Measure Trunk Postural Control.

Science.gov (United States)

López-Plaza, Diego; Juan-Recio, Casto; Barbado, David; Ruiz-Pérez, Iñaki; Vera-Garcia, Francisco J

2018-05-18

Although the Star Excursion Balance test (SEBT) has shown a good intrasession reliability, the intersession reliability of this test has not been deeply studied. Furthermore, there is an evident high influence of the lower limbs in the performance of the SEBT, so even if it has been used to measure core stability, it is possibly not the most suitable measurement. The aims of this study were to (1) to assess the absolute and relative between-session reliability of the SEBT and 2 novel variations of this test to assess trunk postural control while sitting, ie, the Star Excursion Sitting Test (SEST) and the Star Excursion Timing Test (SETT); and (2) to analyze the relationships between these 3 test scores. Correlational and reliability test-retest study. Controlled laboratory environment. Twenty-seven physically active men (age: 24.54 ± 3.05 years). Relative and absolute reliability of the SEBT, SEST, and SETT were calculated through the intraclass correlation coefficient (ICC) and standard error of measurement (SEM), respectively. A Pearson correlation analysis was carried out between the variables of the 3 tests. Maximum normalized reach distances were assessed for different SEBT and SEST directions. In addition, composite indexes were calculated for SEBT, SEST, and SETT. The SEBT (dominant leg: ICC = 0.87 [0.73-0.94], SEM = 2.12 [1.66-2.93]; nondominant leg: ICC = 0.74 [0.50-0.87], SEM = 3.23 [2.54-4.45]), SEST (ICC = 0.85 [0.68-0.92], SEM = 1.27 [1.03-1.80]), and SETT (ICC = 0.61 [0.30-0.80], SEM = 2.31 [1.82-3.17]) composite indexes showed moderate-to-high 1-month reliability. A learning effect was detected for some SEBT and SEST directions and for SEST and SETT composite indexes. No significant correlations were found between SEBT and its 2 variations (r ≤ .366; P > .05). A significant correlation was found between the SEST and SETT composite indexes (r = .520; P > .01). SEBT, SEST, and SETT are reliable field protocols to measure postural control. However

Research and Implementation of Collision Detection Based on Modbus Protocol

Directory of Open Access Journals (Sweden)

Yinglan Fang

2013-01-01

Full Text Available In order to solve the communication errors resulted by traditional working condition multi-platform device communication using the custom protocol communication and link congestion malpractice brought by retransmission, it ensures network communication using time-sharing communication conflict detection based on mature Modbus protocol. Thereby it enhances the stability of the entire system during operation process, and provides simple, efficient, stable business specification interface for the future expansion of the system. After a comprehensive evaluation and analysis of system communication messages before and after improvement, system comprehensive evaluation target has improved. While the system is more flexible to modular design, develop transparent, structure open side and has a broad application prospects.

Daily Readiness Huddles in Radiology-Improving Communication, Coordination, and Problem-Solving Reliability.

Science.gov (United States)

Donnelly, Lane F

Deploying an intentional daily management process is a key part to create high-reliability culture. Key components described in the literature for a successfully daily management process include leadership standard work, visual controls, daily accountability processes, and the discipline to stick to the process over the long term. We believe that the institution of a daily readiness huddle has helped us better coordinate and communicate as a department and improved our ability to deliver imaging services on a daily basis. The daily readiness huddle has enabled us to more rapidly identify issues and has brought accountability to seeing solutions to those issues brought to fruition. In addition, it has helped with team building, including between the radiologists and the nonphysician staff. Copyright © 2017 Elsevier Inc. All rights reserved.

Highly reliable computer network for real time system

International Nuclear Information System (INIS)

Mohammed, F.A.; Omar, A.A.; Ayad, N.M.A.; Madkour, M.A.I.; Ibrahim, M.K.

1988-01-01

Many of computer networks have been studied different trends regarding the network architecture and the various protocols that govern data transfers and guarantee a reliable communication among all a hierarchical network structure has been proposed to provide a simple and inexpensive way for the realization of a reliable real-time computer network. In such architecture all computers in the same level are connected to a common serial channel through intelligent nodes that collectively control data transfers over the serial channel. This level of computer network can be considered as a local area computer network (LACN) that can be used in nuclear power plant control system since it has geographically dispersed subsystems. network expansion would be straight the common channel for each added computer (HOST). All the nodes are designed around a microprocessor chip to provide the required intelligence. The node can be divided into two sections namely a common section that interfaces with serial data channel and a private section to interface with the host computer. This part would naturally tend to have some variations in the hardware details to match the requirements of individual host computers. fig 7

Verbal communication skills in typical language development: a case series.

Science.gov (United States)

Abe, Camila Mayumi; Bretanha, Andreza Carolina; Bozza, Amanda; Ferraro, Gyovanna Junya Klinke; Lopes-Herrera, Simone Aparecida

2013-01-01

The aim of the current study was to investigate verbal communication skills in children with typical language development and ages between 6 and 8 years. Participants were 10 children of both genders in this age range without language alterations. A 30-minute video of each child's interaction with an adult (father and/or mother) was recorded, fully transcribed, and analyzed by two trained researchers in order to determine reliability. The recordings were analyzed according to a protocol that categorizes verbal communicative abilities, including dialogic, regulatory, narrative-discursive, and non-interactive skills. The frequency of use of each category of verbal communicative ability was analyzed (in percentage) for each subject. All subjects used more dialogical and regulatory skills, followed by narrative-discursive and non-interactive skills. This suggests that children in this age range are committed to continue dialog, which shows that children with typical language development have more dialogic interactions during spontaneous interactions with a familiar adult.

A Scenario-Based Protocol Checker for Public-Key Authentication Scheme

Science.gov (United States)

Saito, Takamichi

Security protocol provides communication security for the internet. One of the important features of it is authentication with key exchange. Its correctness is a requirement of the whole of the communication security. In this paper, we introduce three attack models realized as their attack scenarios, and provide an authentication-protocol checker for applying three attack-scenarios based on the models. We also utilize it to check two popular security protocols: Secure SHell (SSH) and Secure Socket Layer/Transport Layer Security (SSL/TLS).

Privacy-Preserving Data Aggregation Protocol for Fog Computing-Assisted Vehicle-to-Infrastructure Scenario

Directory of Open Access Journals (Sweden)

Yanan Chen

2018-01-01

Full Text Available Vehicle-to-infrastructure (V2I communication enables moving vehicles to upload real-time data about road surface situation to the Internet via fixed roadside units (RSU. Thanks to the resource restriction of mobile vehicles, fog computation-enhanced V2I communication scenario has received increasing attention recently. However, how to aggregate the sensed data from vehicles securely and efficiently still remains open to the V2I communication scenario. In this paper, a light-weight and anonymous aggregation protocol is proposed for the fog computing-based V2I communication scenario. With the proposed protocol, the data collected by the vehicles can be efficiently obtained by the RSU in a privacy-preserving manner. Particularly, we first suggest a certificateless aggregate signcryption (CL-A-SC scheme and prove its security in the random oracle model. The suggested CL-A-SC scheme, which is of independent interest, can achieve the merits of certificateless cryptography and signcryption scheme simultaneously. Then we put forward the anonymous aggregation protocol for V2I communication scenario as one extension of the suggested CL-A-SC scheme. Security analysis demonstrates that the proposed aggregation protocol achieves desirable security properties. The performance comparison shows that the proposed protocol significantly reduces the computation and communication overhead compared with the up-to-date protocols in this field.

Synchronous message-based communication for distributed heterogeneous systems

International Nuclear Information System (INIS)

Wilkinson, N.; Dohan, D.

1992-01-01

The use of a synchronous, message-based real-time operating system (Unison) as the basis of transparent interprocess and inter-processor communication over VME-bus is described. The implementation of a synchronous, message-based protocol for network communication between heterogeneous systems is discussed. In particular, the design and implementation of a message-based session layer over a virtual circuit transport layer protocol using UDP/IP is described. Inter-process communication is achieved via a message-based semantic which is portable by virtue of its ease of implementation in other operating system environments. Protocol performance for network communication among heterogeneous architecture is presented, including VMS, Unix, Mach and Unison. (author)

Secret-key expansion from covert communication

Science.gov (United States)

Arrazola, Juan Miguel; Amiri, Ryan

2018-02-01

Covert communication allows the transmission of messages in such a way that it is not possible for adversaries to detect that the communication is occurring. This provides protection in situations where knowledge that two parties are talking to each other may be incriminating to them. In this work, we study how covert communication can be used for a different purpose: secret key expansion. First, we show that any message transmitted in a secure covert protocol is also secret and therefore unknown to an adversary. We then propose a covert communication protocol where the amount of key consumed in the protocol is smaller than the transmitted key, thus leading to secure secret key expansion. We derive precise conditions for secret key expansion to occur, showing that it is possible when there are sufficiently low levels of noise for a given security level. We conclude by examining how secret key expansion from covert communication can be performed in a computational security model.

Bio-Inspired Energy-Aware Protocol Design for Cooperative Wireless Networks

DEFF Research Database (Denmark)

Perrucci, Gian Paolo; Anggraeni, Puri Novelti; Wardana, Satya Ardhy

2011-01-01

In this work, bio-inspired cooperation rules are applied to wireless communication networks. The main goal is to derive cooperative behaviour rules to improve the energy consumption of each mobile device. A medium access control (MAC) protocol particularly designed for peer-to-peer communication...... be achieved by this architecture using game theoretic approaches. As an extension, this work explores the impact of the MAC protocol on the power saving capabilities. This result shows that standard MAC mechanisms are not optimised for the considered cooperative setup. A new MAC protocol is proposed...... among cooperative wireless mobile devices is described. The work is based on a novel communication architecture, where a group of mobile devices are connected both to a cellular base station and among them using short-range communication links. A prior work has investigated the energy saving that can...

Network Challenges for Cyber Physical Systems with Tiny Wireless Devices: A Case Study on Reliable Pipeline Condition Monitoring

Directory of Open Access Journals (Sweden)

Salman Ali

2015-03-01

Full Text Available The synergy of computational and physical network components leading to the Internet of Things, Data and Services has been made feasible by the use of Cyber Physical Systems (CPSs. CPS engineering promises to impact system condition monitoring for a diverse range of fields from healthcare, manufacturing, and transportation to aerospace and warfare. CPS for environment monitoring applications completely transforms human-to-human, human-to-machine and machine-to-machine interactions with the use of Internet Cloud. A recent trend is to gain assistance from mergers between virtual networking and physical actuation to reliably perform all conventional and complex sensing and communication tasks. Oil and gas pipeline monitoring provides a novel example of the benefits of CPS, providing a reliable remote monitoring platform to leverage environment, strategic and economic benefits. In this paper, we evaluate the applications and technical requirements for seamlessly integrating CPS with sensor network plane from a reliability perspective and review the strategies for communicating information between remote monitoring sites and the widely deployed sensor nodes. Related challenges and issues in network architecture design and relevant protocols are also provided with classification. This is supported by a case study on implementing reliable monitoring of oil and gas pipeline installations. Network parameters like node-discovery, node-mobility, data security, link connectivity, data aggregation, information knowledge discovery and quality of service provisioning have been reviewed.

Network challenges for cyber physical systems with tiny wireless devices: a case study on reliable pipeline condition monitoring.

Science.gov (United States)

Ali, Salman; Qaisar, Saad Bin; Saeed, Husnain; Khan, Muhammad Farhan; Naeem, Muhammad; Anpalagan, Alagan

2015-03-25

The synergy of computational and physical network components leading to the Internet of Things, Data and Services has been made feasible by the use of Cyber Physical Systems (CPSs). CPS engineering promises to impact system condition monitoring for a diverse range of fields from healthcare, manufacturing, and transportation to aerospace and warfare. CPS for environment monitoring applications completely transforms human-to-human, human-to-machine and machine-to-machine interactions with the use of Internet Cloud. A recent trend is to gain assistance from mergers between virtual networking and physical actuation to reliably perform all conventional and complex sensing and communication tasks. Oil and gas pipeline monitoring provides a novel example of the benefits of CPS, providing a reliable remote monitoring platform to leverage environment, strategic and economic benefits. In this paper, we evaluate the applications and technical requirements for seamlessly integrating CPS with sensor network plane from a reliability perspective and review the strategies for communicating information between remote monitoring sites and the widely deployed sensor nodes. Related challenges and issues in network architecture design and relevant protocols are also provided with classification. This is supported by a case study on implementing reliable monitoring of oil and gas pipeline installations. Network parameters like node-discovery, node-mobility, data security, link connectivity, data aggregation, information knowledge discovery and quality of service provisioning have been reviewed.

Entangled photons and quantum communication

Energy Technology Data Exchange (ETDEWEB)

Yuan Zhensheng, E-mail: yuanzs@ustc.edu.c [Hefei National Laboratory for Physical Sciences at Microscale and Department of Modern Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); Physikalisches Institut, Universitaet Heidelberg, Philosophenweg 12, 69120 Heidelberg (Germany); Bao Xiaohui [Hefei National Laboratory for Physical Sciences at Microscale and Department of Modern Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); Physikalisches Institut, Universitaet Heidelberg, Philosophenweg 12, 69120 Heidelberg (Germany); Lu Chaoyang; Zhang Jun; Peng Chengzhi [Hefei National Laboratory for Physical Sciences at Microscale and Department of Modern Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); Pan Jianwei, E-mail: pan@ustc.edu.c [Hefei National Laboratory for Physical Sciences at Microscale and Department of Modern Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); Physikalisches Institut, Universitaet Heidelberg, Philosophenweg 12, 69120 Heidelberg (Germany)

2010-12-15

This article reviews the progress of quantum communication that utilizes photonic entanglement. We start with a survey of various methods for generating entangled photons, followed by an introduction of the theoretical principles and the experimental implementations of quantum key distribution. We then move on to a discussion of more involved quantum communication protocols including quantum dense coding, teleportation and quantum communication complexity. After that, we review the progress in free-space quantum communication, decoherence-free subspace, and quantum repeater protocols which are essential ingredients for long-distance quantum communication. Practical realizations of quantum repeaters, which require an interface between photons and quantum memories, are discussed briefly. Finally, we draw concluding remarks considering the technical challenges, and put forward an outlook on further developments of this field.

Entangled photons and quantum communication

International Nuclear Information System (INIS)

Yuan Zhensheng; Bao Xiaohui; Lu Chaoyang; Zhang Jun; Peng Chengzhi; Pan Jianwei

2010-01-01

This article reviews the progress of quantum communication that utilizes photonic entanglement. We start with a survey of various methods for generating entangled photons, followed by an introduction of the theoretical principles and the experimental implementations of quantum key distribution. We then move on to a discussion of more involved quantum communication protocols including quantum dense coding, teleportation and quantum communication complexity. After that, we review the progress in free-space quantum communication, decoherence-free subspace, and quantum repeater protocols which are essential ingredients for long-distance quantum communication. Practical realizations of quantum repeaters, which require an interface between photons and quantum memories, are discussed briefly. Finally, we draw concluding remarks considering the technical challenges, and put forward an outlook on further developments of this field.

Robust quantum secure direct communication and authentication protocol against decoherence noise based on six-qubit DF state

International Nuclear Information System (INIS)

Chang Yan; Zhang Shi-Bin; Yan Li-Li; Han Gui-Hua

2015-01-01

By using six-qubit decoherence-free (DF) states as quantum carriers and decoy states, a robust quantum secure direct communication and authentication (QSDCA) protocol against decoherence noise is proposed. Four six-qubit DF states are used in the process of secret transmission, however only the |0′〉 state is prepared. The other three six-qubit DF states can be obtained by permuting the outputs of the setup for |0′〉. By using the |0′〉 state as the decoy state, the detection rate and the qubit error rate reach 81.3%, and they will not change with the noise level. The stability and security are much higher than those of the ping–pong protocol both in an ideal scenario and a decoherence noise scenario. Even if the eavesdropper measures several qubits, exploiting the coherent relationship between these qubits, she can gain one bit of secret information with probability 0.042. (paper)

The Accelerator Reliability Forum

CERN Document Server

Lüdeke, Andreas; Giachino, R

2014-01-01

A high reliability is a very important goal for most particle accelerators. The biennial Accelerator Reliability Workshop covers topics related to the design and operation of particle accelerators with a high reliability. In order to optimize the over-all reliability of an accelerator one needs to gather information on the reliability of many different subsystems. While a biennial workshop can serve as a platform for the exchange of such information, the authors aimed to provide a further channel to allow for a more timely communication: the Particle Accelerator Reliability Forum [1]. This contribution will describe the forum and advertise it’s usage in the community.

New control system: net communications on VAX; Nouveau systeme de controle: communications reseau sur VAX

Energy Technology Data Exchange (ETDEWEB)

David, L; Maugeais, C

1993-12-31

The control system is made of five different types of processors: a server (VAX 3800), stations (VS4000) as setting interfaces for operators, CAMAC VANTAGE controllers, VME controllers and industrial programmable automates. These automates are treated with the IMAGIN supervision software and with the OSI communication protocol. All the processors are of the VAX family and use DECNET communication protocol on ETHERNET net. (A.B.). 3 figs.

Design Protocols and Analytical Strategies that Incorporate Structural Reliability Models

Science.gov (United States)

Duffy, Stephen F.

1997-01-01

Al single crystal turbine blade material; map a simplistic failure strength envelope of the material; develop a statistically based reliability computer algorithm, verify the reliability model and computer algorithm, and model stator vanes for rig tests. Thus establishing design protocols that enable the engineer to analyze and predict the mechanical behavior of ceramic composites and intermetallics would mitigate the prototype (trial and error) approach currently used by the engineering community. The primary objective of the research effort supported by this short term grant is the continued creation of enabling technologies for the macroanalysis of components fabricated from ceramic composites and intermetallic material systems. The creation of enabling technologies aids in shortening the product development cycle of components fabricated from the new high technology materials.

Probabilistic Location-based Routing Protocol for Mobile Wireless Sensor Networks with Intermittent Communication

Directory of Open Access Journals (Sweden)

Sho KUMAGAI

2015-02-01

Full Text Available In a sensor network, sensor data messages reach the nearest stationary sink node connected to the Internet by wireless multihop transmissions. Recently, various mobile sensors are available due to advances of robotics technologies and communication technologies. A location based message-by-message routing protocol, such as Geographic Distance Routing (GEDIR is suitable for such mobile wireless networks; however, it is required for each mobile wireless sensor node to know the current locations of all its neighbor nodes. On the other hand, various intermittent communication methods for a low power consumption requirement have been proposed for wireless sensor networks. Intermittent Receiver-driven Data Transmission (IRDT is one of the most efficient methods; however, it is difficult to combine the location based routing and the intermittent communication. In order to solve this problem, this paper proposes a probabilistic approach IRDT-GEDIR with the help of one of the solutions of the secretaries problem. Here, each time a neighbor sensor node wakes up from its sleep mode, an intermediate sensor node determines whether it forwards its buffered sensor data messages to it or not based on an estimation of achieved pseudo speed of the messages. Simulation experiments show that IRDT-GEDIR achieves higher pseudo speed of sensor data message transmissions and shorter transmission delay than achieves shorter transmission delay than the two naive combinations of IRDT and GEDIR in sensor networks with mobile sensor nodes and a stationary sink node. In addition, the guideline of the estimated numbers of the neighbor nodes of each intermediate sensor node is provided based on the results of the simulation experiments to apply the probabilistic approach IRDT-GEDIR.

A web-based team-oriented medical error communication assessment tool: development, preliminary reliability, validity, and user ratings.

Science.gov (United States)

Kim, Sara; Brock, Doug; Prouty, Carolyn D; Odegard, Peggy Soule; Shannon, Sarah E; Robins, Lynne; Boggs, Jim G; Clark, Fiona J; Gallagher, Thomas

2011-01-01

Multiple-choice exams are not well suited for assessing communication skills. Standardized patient assessments are costly and patient and peer assessments are often biased. Web-based assessment using video content offers the possibility of reliable, valid, and cost-efficient means for measuring complex communication skills, including interprofessional communication. We report development of the Web-based Team-Oriented Medical Error Communication Assessment Tool, which uses videotaped cases for assessing skills in error disclosure and team communication. Steps in development included (a) defining communication behaviors, (b) creating scenarios, (c) developing scripts, (d) filming video with professional actors, and (e) writing assessment questions targeting team communication during planning and error disclosure. Using valid data from 78 participants in the intervention group, coefficient alpha estimates of internal consistency were calculated based on the Likert-scale questions and ranged from α=.79 to α=.89 for each set of 7 Likert-type discussion/planning items and from α=.70 to α=.86 for each set of 8 Likert-type disclosure items. The preliminary test-retest Pearson correlation based on the scores of the intervention group was r=.59 for discussion/planning and r=.25 for error disclosure sections, respectively. Content validity was established through reliance on empirically driven published principles of effective disclosure as well as integration of expert views across all aspects of the development process. In addition, data from 122 medicine and surgical physicians and nurses showed high ratings for video quality (4.3 of 5.0), acting (4.3), and case content (4.5). Web assessment of communication skills appears promising. Physicians and nurses across specialties respond favorably to the tool.

The Simplest Protocol for Oblivious Transfer

DEFF Research Database (Denmark)

Chou, Tung; Orlandi, Claudio

2015-01-01

Oblivious Transfer (OT) is the fundamental building block of cryptographic protocols. In this paper we describe the simplest and most efficient protocol for 1-out-of-n OT to date, which is obtained by tweaking the Diffie-Hellman key-exchange protocol. The protocol achieves UC-security against...... active and adaptive corruptions in the random oracle model. Due to its simplicity, the protocol is extremely efficient and it allows to perform m 1-out-of-n OTs using only: - Computation: (n+1)m+2 exponentiations (mn for the receiver, mn+2 for the sender) and - Communication: 32(m+1) bytes (for the group...... optimizations) is at least one order of magnitude faster than previous work. Category / Keywords: cryptographic protocols / Oblivious Transfer, UC Security, Elliptic Curves, Efficient Implementation...

Innovation and international business communication : can European research help to increase the validity and reliability for our business and teaching practice?

NARCIS (Netherlands)

Ulijn, J.M.

2000-01-01

We can improve the validity and reliability of business communication research by using both quantitative and qualitative methods and studying both real life and simulations. Studies should build on both American research on strategy and innovation and European research on psycholinguistics and

Reliability of Videoconferencing Administration of a Communication Questionnaire to People With Traumatic Brain Injury and Their Close Others.

Science.gov (United States)

Rietdijk, Rachael; Power, Emma; Brunner, Melissa; Togher, Leanne

To compare in-person with videoconferencing administration of a communication questionnaire for people with traumatic brain injury (TBI) and their close others. Repeated-measures design with randomized order of administration. Twenty adults with severe TBI and their close others. Both participants with TBI and their close others completed the La Trobe Communication Questionnaire (LCQ) via interview with a clinician, once via Skype and once during a home visit. Total LCQ score and time taken for completion. There were no significant differences between videoconferencing and in-person conditions in the total scores or time taken to complete the questionnaire. Videoconferencing-based administration of the LCQ is as reliable and efficient as in-person administration.

Effectiveness and Limitations of E-Mail Security Protocols

OpenAIRE

M. Tariq Banday

2011-01-01

Simple Mail Transport Protocol is the most widely adopted protocol for e-mail delivery. However, it lackssecurity features for privacy, authentication of sending party, integrity of e-mail message, nonrepudiationand consistency of e-mail envelope. To make e-mail communication secure and private,e-mail servers incorporate one or more security features using add-on security protocols. The add-onsecurity protocols provide a reasonable security but have several limitations. This paper discussesli...

Multiparty quantum secret sharing of secure direct communication

International Nuclear Information System (INIS)

Zhang Zhanjun

2005-01-01

Based on the two-step protocol [F.G. Deng, G.L. Long, X.S. Liu, Phys. Rev. A 68 (2003) 042317], we propose a (n,n)-threshold multiparty quantum secret sharing protocol of secure direct communication. In our protocol, the sender's secure direct communication message can be extracted only if all the sharers collaborate. We show a variant version of this protocol based on the variant two-step protocol. This variant version can considerably reduce the realization difficulty in experiment. In contrast to the use of multi-particle GHZ states in the case that the sharer number is larger than 3, the use and identification of Bell states are enough in our two protocols disregarding completely the sharer number, hence, our protocols are more feasible in technique

VANET Routing Protocols: Pros and Cons

OpenAIRE

Paul, Bijan; Ibrahim, Md.; Bikas, Md. Abu Naser

2012-01-01

VANET (Vehicular Ad-hoc Network) is a new technology which has taken enormous attention in the recent years. Due to rapid topology changing and frequent disconnection makes it difficult to design an efficient routing protocol for routing data among vehicles, called V2V or vehicle to vehicle communication and vehicle to road side infrastructure, called V2I. The existing routing protocols for VANET are not efficient to meet every traffic scenarios. Thus design of an efficient routing protocol h...

Advanced Internet Protocols, Services, and Applications

CERN Document Server

Oki, Eiji; Tatipamula, Mallikarjun; Vogt, Christian

2012-01-01

Today, the internet and computer networking are essential parts of business, learning, and personal communications and entertainment. Virtually all messages or transactions sent over the internet are carried using internet infrastructure- based on advanced internet protocols. Advanced internet protocols ensure that both public and private networks operate with maximum performance, security, and flexibility. This book is intended to provide a comprehensive technical overview and survey of advanced internet protocols, first providing a solid introduction and going on to discu

Authentication Protocols for Internet of Things: A Comprehensive Survey

Directory of Open Access Journals (Sweden)

Mohamed Amine Ferrag

2017-01-01

Full Text Available In this paper, a comprehensive survey of authentication protocols for Internet of Things (IoT is presented. Specifically more than forty authentication protocols developed for or applied in the context of the IoT are selected and examined in detail. These protocols are categorized based on the target environment: (1 Machine to Machine Communications (M2M, (2 Internet of Vehicles (IoV, (3 Internet of Energy (IoE, and (4 Internet of Sensors (IoS. Threat models, countermeasures, and formal security verification techniques used in authentication protocols for the IoT are presented. In addition a taxonomy and comparison of authentication protocols that are developed for the IoT in terms of network model, specific security goals, main processes, computation complexity, and communication overhead are provided. Based on the current survey, open issues are identified and future research directions are proposed.

A Novel Reliability Enhanced Handoff Method in Future Wireless Heterogeneous Networks

Directory of Open Access Journals (Sweden)

Wang YuPeng

2016-01-01

Full Text Available As the demand increases, future networks will follow the trends of network variety and service flexibility, which requires heterogeneous type of network deployment and reliable communication method. In practice, most communication failure happens due to the bad radio link quality, i.e., high-speed users suffers a lot on the problem of radio link failure, which causes the problem of communication interrupt and radio link recovery. To make the communication more reliable, especially for the high mobility users, we propose a novel communication handoff mechanism to reduce the occurrence of service interrupt. Based on computer simulation, we find that the reliability on the service is greatly improved.

Measurement of communication satisfaction. Evaluating the Communication Satisfaction Questionnaire as a communication audit tool

NARCIS (Netherlands)

Koning, K.H.; de Jong, Menno D.T.

2007-01-01

Despite the number of publications about auditing organizational communication, scholars have paid little attention to the reliability and validity of individual audit techniques. This study examines the merits and restrictions of the Communication Satisfaction Questionnaire (CSQ) by comparing CSQ

Delay Tolerance in Underwater Wireless Communications: A Routing Perspective

Directory of Open Access Journals (Sweden)

Safdar Hussain Bouk

2016-01-01

Full Text Available Similar to terrestrial networks, underwater wireless networks (UWNs also aid several critical tasks including coastal surveillance, underwater pollution detection, and other maritime applications. Currently, once underwater sensor nodes are deployed at different levels of the sea, it is nearly impossible or very expensive to reconfigure the hardware, for example, battery. Taking this issue into account, considerable amount of research has been carried out to ensure minimum energy costs and reliable communication between underwater nodes and base stations. As a result, several different network protocols were proposed for UWN, including MAC, PHY, transport, and routing. Recently, a new paradigm was introduced claiming that the intermittent nature of acoustic channel and signal resulted in designing delay tolerant routing schemes for the UWN, known as an underwater delay tolerant network. In this paper, we provide a comprehensive survey of underwater routing protocols with emphasis on the limitations, challenges, and future open issues in the context of delay tolerant network routing.

Medical students' communication skills in clinical education: Results from a cohort study.

Science.gov (United States)

Bachmann, Cadja; Roschlaub, Silke; Harendza, Sigrid; Keim, Rebecca; Scherer, Martin

2017-10-01

To assess students' communication skills during clinical medical education and at graduation. We conducted an observational cohort study from 2007 to 2011 with 26 voluntary undergraduate medical students at Hamburg University based on video-taped consultations in year four and at graduation. 176 consultations were analyzed quantitatively with validated and non-validated context-independent communication observation instruments (interrater reliability ≥0.8). Based on observational protocols each consultation was also documented in free-text comments, salient topics were extracted afterwards. 26 students, seven males, were enrolled in the survey. On average, graduates scored higher in differential-diagnostic questioning and time management but showed deficiencies in taking systematic and complete symptom-oriented histories, in communication techniques, in structuring consultations and in gathering the patients' perspectives. Patient-centeredness and empathy were rather low at graduation. Individual deficiencies could barely be eliminated. Medical students were able to enhance their clinical reasoning skills and their time management. Still, various communication deficiencies in final year students became evident regarding appropriate history taking, communication skills, empathy and patient-centeredness. The necessity of developing a longitudinal communication curriculum with enhanced communication trainings and assessments became evident. A curriculum should ensure that students' communication competencies are firmly achieved at graduation. Copyright © 2017. Published by Elsevier B.V.

An Enhanced Backbone-Assisted Reliable Framework for Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Amna Ali

2010-03-01

Full Text Available An extremely reliable source to sink communication is required for most of the contemporary WSN applications especially pertaining to military, healthcare and disaster-recovery. However, due to their intrinsic energy, bandwidth and computational constraints, Wireless Sensor Networks (WSNs encounter several challenges in reliable source to sink communication. In this paper, we present a novel reliable topology that uses reliable hotlines between sensor gateways to boost the reliability of end-to-end transmissions. This reliable and efficient routing alternative reduces the number of average hops from source to the sink. We prove, with the help of analytical evaluation, that communication using hotlines is considerably more reliable than traditional WSN routing. We use reliability theory to analyze the cost and benefit of adding gateway nodes to a backbone-assisted WSN. However, in hotline assisted routing some scenarios where source and the sink are just a couple of hops away might bring more latency, therefore, we present a Signature Based Routing (SBR scheme. SBR enables the gateways to make intelligent routing decisions, based upon the derived signature, hence providing lesser end-to-end delay between source to the sink communication. Finally, we evaluate our proposed hotline based topology with the help of a simulation tool and show that the proposed topology provides manifold increase in end-to-end reliability.

Implementation of postoperative handoff protocol

African Journals Online (AJOL)

Background: Standardised handoff protocols have become necessary patient ... improve the perioperative handoff communications from the cardiac operating theatres to the ICU. ..... as you can imagine, there was push-back to the change.

Communication Schemes with Constrained Reordering of Resources

DEFF Research Database (Denmark)

Popovski, Petar; Utkovski, Zoran; Trillingsgaard, Kasper Fløe

2013-01-01

This paper introduces a communication model inspired by two practical scenarios. The first scenario is related to the concept of protocol coding, where information is encoded in the actions taken by an existing communication protocol. We investigate strategies for protocol coding via combinatorial...... reordering of the labelled user resources (packets, channels) in an existing, primary system. However, the degrees of freedom of the reordering are constrained by the operation of the primary system. The second scenario is related to communication systems with energy harvesting, where the transmitted signals...... are constrained by the energy that is available through the harvesting process. We have introduced a communication model that covers both scenarios and elicits their key feature, namely the constraints of the primary system or the harvesting process. We have shown how to compute the capacity of the channels...

A Proof-checked Verification of a Real-Time Communication Protocol

NARCIS (Netherlands)

Polak, I.

We present an analysis of a protocol developed by Philips to connect several components of an audio-system. The verification of the protocol is carried out using the timed I/O-automata model of Lynch and Vaandrager. The verification has been partially proof-checked with the interactive proof

Efficient quantum secure communication with a publicly known key

International Nuclear Information System (INIS)

Li Chunyan; Li Xihan; Deng Fuguo; Zhou Hongyu

2008-01-01

This paper presents a simple way for an eavesdropper to eavesdrop freely the secret message in the experimental realization of quantum communication protocol proposed by Beige et al (2002 Acta Phys. Pol. A 101 357). Moreover, it introduces an efficient quantum secure communication protocol based on a publicly known key with decoy photons and two biased bases by modifying the original protocol. The total efficiency of this new protocol is double that of the original one. With a low noise quantum channel, this protocol can be used for transmitting a secret message. At present, this protocol is good for generating a private key efficiently. (general)

Adaptive Protocols for Mobile Wireless Networks

National Research Council Canada - National Science Library

Pursley, Michael B

2005-01-01

.... Research results are presented on adaptive, energy-efficient, distributed protocols for mobile wireless networks that must operate effectively over unreliable communication links in highly dynamic...

The effect on reliability and sensitivity to level of training of combining analytic and holistic rating scales for assessing communication skills in an internal medicine resident OSCE.

Science.gov (United States)

Daniels, Vijay John; Harley, Dwight

2017-07-01

Although previous research has compared checklists to rating scales for assessing communication, the purpose of this study was to compare the effect on reliability and sensitivity to level of training of an analytic, a holistic, and a combined analytic-holistic rating scale in assessing communication skills. The University of Alberta Internal Medicine Residency runs OSCEs for postgraduate year (PGY) 1 and 2 residents and another for PGY-4 residents. Communication stations were scored with an analytic scale (empathy, non-verbal skills, verbal skills, and coherence subscales) and a holistic scale. Authors analyzed reliability of individual and combined scales using generalizability theory and evaluated each scale's sensitivity to level of training. For analytic, holistic, and combined scales, 12, 12, and 11 stations respectively yielded a Phi of 0.8 for the PGY-1,2 cohort, and 16, 16, and 14 stations yielded a Phi of 0.8 for the PGY-4 cohort. PGY-4 residents scored higher on the combined scale, the analytic rating scale, and the non-verbal and coherence subscales. A combined analytic-holistic rating scale increased score reliability and was sensitive to level of training. Given increased validity evidence, OSCE developers should consider combining analytic and holistic scales when assessing communication skills. Copyright © 2017 Elsevier B.V. All rights reserved.

Study of QoS control and reliable routing method for utility communication network. Application of differentiated service to the network and alternative route establishment by the IP routing protocol; Denryokuyo IP network no QoS seigyo to shinraisei kakuho no hoho. DiffServ ni yoru QoS seigyo no koka to IP ni yoru fuku root ka no kento

Energy Technology Data Exchange (ETDEWEB)

Oba, E.

2000-05-01

QoS control method which satisfies utilities communication network requirement and alternative route establishment method which is for sustaining communication during a failure are studied. Applicability of DiffServ (Differentiated Service), one of the most promising QoS control method on IP network and studying energetically in IETF WG, is studied and it is found most application used in the utility communication network except for relaying system information could he accommodated to the DiffServ network. An example of the napping of the utility communication applications to the DiffServ PHB (Per Hop Behavior) is shown in this paper. Regarding to the alternative route, usual IP routing protocol cannot establish alternative route which doesn't have common links and nodes in their paths for a destination. IP address duplication with some modification of routing protocol enables such alternative route establishment. MPLS, distance vector algorithm and link state algorithm are evaluated qualitatively, and as a result, we found MPLS is promising way to establish the route. Quantitative evaluation will be future work. (author)

OR.NET RT: how service-oriented medical device architecture meets real-time communication.

Science.gov (United States)

Pfeiffer, Jonas H; Kasparick, Martin; Strathen, Benjamin; Dietz, Christian; Dingler, Max E; Lueth, Tim C; Timmermann, Dirk; Radermacher, Klaus; Golatowski, Frank

2018-02-23

Today's landscape of medical devices is dominated by stand-alone systems and proprietary interfaces lacking cross-vendor interoperability. This complicates or even impedes the innovation of novel, intelligent assistance systems relying on the collaboration of medical devices. Emerging approaches use the service-oriented architecture (SOA) paradigm based on Internet protocol (IP) to enable communication between medical devices. While this works well for scenarios with no or only soft timing constraints, the underlying best-effort communication scheme is insufficient for time critical data. Real-time (RT) networks are able to reliably guarantee fixed latency boundaries, for example, by using time division multiple access (TDMA) communication patterns. However, deterministic RT networks come with their own limitations such as tedious, inflexible configuration and a more restricted bandwidth allocation. In this contribution we overcome the drawbacks of both approaches by describing and implementing mechanisms that allow the two networks to interact. We introduce the first implementation of a medical device network that offers hard RT guarantees for control and sensor data and integrates into SOA networks. Based on two application examples we show how the flexibility of SOA networks and the reliability of RT networks can be combined to achieve an open network infrastructure for medical devices in the operating room (OR).

Development of IT-based data communication network technology

International Nuclear Information System (INIS)

Hong, Seok Boong; Jeong, K. I.; Yoo, Y. R.

2010-10-01

- Developing broadband high-reliability real-time communications technology for NPP - Developing reliability and performance validation technology for communications network - Developing security technology for NPP communications network - Developing field communications network for harsh environment of NPP - International standard registration(Oct. 28, 2009, IEC 61500

Quantum-key-distribution protocol with pseudorandom bases

Science.gov (United States)

Trushechkin, A. S.; Tregubov, P. A.; Kiktenko, E. O.; Kurochkin, Y. V.; Fedorov, A. K.

2018-01-01

Quantum key distribution (QKD) offers a way for establishing information-theoretical secure communications. An important part of QKD technology is a high-quality random number generator for the quantum-state preparation and for post-processing procedures. In this work, we consider a class of prepare-and-measure QKD protocols, utilizing additional pseudorandomness in the preparation of quantum states. We study one of such protocols and analyze its security against the intercept-resend attack. We demonstrate that, for single-photon sources, the considered protocol gives better secret key rates than the BB84 and the asymmetric BB84 protocols. However, the protocol strongly requires single-photon sources.

The reliability of knee joint position testing using electrogoniometry

Directory of Open Access Journals (Sweden)

Winter Adele

2008-01-01

Full Text Available Abstract Background The current investigation examined the inter- and intra-tester reliability of knee joint angle measurements using a flexible Penny and Giles Biometric® electrogoniometer. The clinical utility of electrogoniometry was also addressed. Methods The first study examined the inter- and intra-tester reliability of measurements of knee joint angles in supine, sitting and standing in 35 healthy adults. The second study evaluated inter-tester and intra-tester reliability of knee joint angle measurements in standing and after walking 10 metres in 20 healthy adults, using an enhanced measurement protocol with a more detailed electrogoniometer attachment procedure. Both inter-tester reliability studies involved two testers. Results In the first study, inter-tester reliability (ICC[2,10] ranged from 0.58–0.71 in supine, 0.68–0.79 in sitting and 0.57–0.80 in standing. The standard error of measurement between testers was less than 3.55° and the limits of agreement ranged from -12.51° to 12.21°. Reliability coefficients for intra-tester reliability (ICC[3,10] ranged from 0.75–0.76 in supine, 0.86–0.87 in sitting and 0.87–0.88 in standing. The standard error of measurement for repeated measures by the same tester was less than 1.7° and the limits of agreement ranged from -8.13° to 7.90°. The second study showed that using a more detailed electrogoniometer attachment protocol reduced the error of measurement between testers to 0.5°. Conclusion Using a standardised protocol, reliable measures of knee joint angles can be gained in standing, supine and sitting by using a flexible goniometer.

Modelling and Initial Validation of the DYMO Routing Protocol for Mobile Ad-Hoc Networks

DEFF Research Database (Denmark)

Espensen, Kristian Asbjørn Leth; Kjeldsen, Mads Keblov; Kristensen, Lars Michael

2008-01-01

A mobile ad-hoc network (MANET) is an infrastructureless network established by a set of mobile devices using wireless communication. The Dynamic MANET On-demand (DYMO) protocol is a routing protocol for multi-hop communication in MANETs currently under development by the Internet Engineering Task...... Force (IETF). This paper presents a Coloured Petri Net (CPN) model of the mandatory parts of the DYMO protocol, and shows how scenario-based state space exploration has been used to validate key properties of the protocol. Our CPN modelling and verification work has spanned two revisions of the DYMO...... protocol specification and have had direct impact on the most recent version of the protocol specification....

Anonymous quantum communications using the quantum one-time pad

International Nuclear Information System (INIS)

Wang, Qing-Le; Gao, Fei-; Liu, Bin; Song, Ting-Ting; Wen, Qiao-Yan

2015-01-01

We present the first quantum secure communication protocol for an anonymous receiver without the assistance of anonymous entanglement. In previous works, if a public sender wants to send quantum messages to a chosen receiver while protecting the identity of the receiver from others, all participants should cooperate first to construct the entanglement between the sender and the anonymous receiver. This is the most important process in anonymous quantum communications. With anonymous entanglement, the sender can communicate quantum messages to the anonymous receiver by applying teleportation protocols. In contrast, our protocol is novel and achieves communication of quantum messages directly from the public sender to the anonymous receiver based on the quantum one-time pad and current achievements. Notably, the anonymity of the receiver, as well as the privacy of the quantum messages, is perfectly protected with the exception of an exponentially small probability in our protocol. (paper)

Design & Test of Radio Communication and Control System for Aquaculture

Directory of Open Access Journals (Sweden)

Fengrong Jia

2013-05-01

Full Text Available Aiming at low automation degree and backward aquatic product management of current aquaculture in China, this paper designed a set of radio communication and control system which consists of 3 parts of information collection module, control module and radio communication module. This system both realizes wireless monitoring of quality parameters of water for aquaculture and realizes wireless control of water level and dissolved oxygen value through radio communication. Test results show that data transfer is more accurate and reliable after adding customized protocol and answer signals in radio communication. The highest error and missing rate within 1000 m is 0.36, the lowest error and missing rate is 0.05 and the longest response time is 49 ms. The dissolved oxygen value detection system designed in this paper is close to the testing value of existing dissolved oxygen value transmitter DO6309. With wireless data transfer mode, it has higher practicality. The wireless control of dissolved oxygen value and water level can be controlled within the appropriate range with stable and precise control. The study results can provide intelligent aquaculture model with simple operation and precise control for enormous aquatic breeders