Testing of elastomer seals using small-size rigs

International Nuclear Information System (INIS)

Leeks, C.W.E.; Dunford, B.; Barnfield, J.H.; Gray, I.L.S.

1997-01-01

This paper looks at the use of small size seal leakage test rigs to demonstrate the compliance of full size container seals against the IAEA Transport Regulation's limits for activity release for normal transport and accident conditions. The detailed requirements of the regulations are discussed and it is concluded that an appropriate test programme to meet these requirements using only small size test rigs, can normally be set up and carried out on a relatively short time scale. It is important that any small test rigs should be designed to represent the relevant features of the seal arrangement and the overall test programme should cover all of the conditions, specified by the regulations, for the type, classification and contents of the container under consideration. The parameters of elastomer O-rings, which affect their sealing ability, are considered and those which are amenable to small scale testing or have to be modelled at full size are identified. Generally, the seals used in leakage tests have to be modelled with a full size cross-section but can have a reduced peripheral length. (Author)

Impacts of PV Array Sizing on PV Inverter Lifetime and Reliability

DEFF Research Database (Denmark)

Sangwongwanich, Ariya; Yang, Yongheng; Sera, Dezso

2017-01-01

. However, oversizing the PV array will increase the loading of PV inverters, which may have undesired influence on the PV inverter lifetime and reliability. In that case, it may result in a negative impact on the overall PV energy cost, due to the increased maintenance for the PV inverters. This paper...... evaluates the lifetime of PV inverters considering the PV array sizing and installation sites, e.g., Denmark and Arizona. The results reveal that the PV array sizing has a considerable impact on the PV inverter lifetime and reliability, especially in Denmark, where the average solar irradiance level...

Trade-offs in size, quantity and reliability of generalized nuclear power plants

International Nuclear Information System (INIS)

Hill, D.; Mubayi, V.

1987-01-01

In the 1960's and 1970's, there was rapid growth in the size of newly started nuclear power plants because of the anticipated advantages of increasing scale. Any such advantages were overwhelmed by the complications that arose with long construction times, and attention is now being given to a ''second generation'' of smaller plants of new design. Providing the same production capacity will require larger numbers of plants if they are smaller. Although it seems to have received little attention previously, there should be compensating economies due to ''learning curve'' effects in the manufacture of multiple units of standardized designs (Hill 1983). Moreover, the use of a large number of smaller units increases the overall system reliability. On balance, however, it is not clear how scale, quantity, and reliability considerations interact to determine optimal plant size. The purpose of this paper is to begin examining the size-quantity tradeoff taking into account scale effects, the manufacturing learning curve, plant availability, and system reliability

Effect of small mapping population sizes on reliability of quantitative ...

African Journals Online (AJOL)

A limitation of quantitative trait loci (QTL) mapping is that accuracy of determining QTL position and effects are largely determined by population size. Despite the importance of this concept, known as the "Beavis effect there has generally been a lack of understanding by molecular geneticists and breeders. One possible ...

77 FR 39442 - Receipts-Based, Small Business Size Standard

Science.gov (United States)

2012-07-03

... RIN 3150-AJ14 [NRC-2012-0062] Receipts-Based, Small Business Size Standard AGENCY: Nuclear Regulatory... Regulatory Flexibility Act of 1980, as amended. The NRC is proposing to increase its receipts-based, small business size standard from $6.5 million to $7 million to conform to the standard set by the Small Business...

78 FR 77334 - Small Business Size Standards: Construction

Science.gov (United States)

2013-12-23

... enrollment in the System of Award Management's (SAM) Dynamic Small Business Search database, and more firms... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG37 Small Business Size Standards: Construction AGENCY: U.S. Small Business Administration. ACTION: Final rule. SUMMARY: The United States Small...

Investigation of small and modular-sized fast reactor

International Nuclear Information System (INIS)

Kubota, Kenichi; Kawasaki, Nobuchika; Umetsu, Yoichiro; Akatsu, Minoru; Kasai, Shigeo; Konomura, Mamoru; Ichimiya, Masakazu

2000-06-01

In this paper, feasibility of the multipurpose small fast reactor, which could be used for requirements concerned with various utilization of electricity and energy and flexibility of power supply site, is discussed on the basis of examination of literatures of various small reactors. And also, a possibility of economic improvement by learning effect of fabrication cost is discussed for the modular-sized reactor which is expected to be a base load power supply system with lower initial investment. (1) Multipurpose small reactor (a) The small reactor with 10MWe-150MWe has a potential as a power source for large co-generation, a large island, a middle city, desalination and marine use. (b) Highly passive mechanism, long fuel exchange interval, and minimized maintenance activities are required for the multipurpose small reactor design. The reactor has a high potential for the long fuel exchange interval, since it is relatively easy for FR to obtain a long life core. (c) Current designs of small FRs in Japan and USA (NERI Project) are reviewed to obtain design requirements for the multipurpose small reactor. (2) Modular-sized reactor (a) In order that modular-sized reactor could be competitive to 3200MWe twin plant (two large monolithic reactor) with 200kyenWe, the target capital cost of FOAK is estimated to be 260kyen/yenWe for 800MWe modular, 280kyen/yenWe for 400MWe modular and 290kyen/yenWe for 200MWe by taking account of the leaning effect. (b) As the result of the review on the current designs of modular-sized FRs in Japan and USA (S-PRISM) from the viewpoint of economic improvement, since it only be necessary to make further effort for the target capital cost of FOAK, since the modular-sized FRs requires a large amount of material for shielding, vessels and heat exchangers essentially. (author)

76 FR 27935 - Small Business Size Standards: Transportation and Warehousing

Science.gov (United States)

2011-05-13

... assistance, SBA establishes small business definitions (referred to as size standards) for private sector... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG08 Small Business Size Standards: Transportation and Warehousing AGENCY: U.S. Small Business Administration. ACTION: Proposed rule. SUMMARY: The U...

Chironomid midges (Diptera, chironomidae) show extremely small genome sizes.

Science.gov (United States)

Cornette, Richard; Gusev, Oleg; Nakahara, Yuichi; Shimura, Sachiko; Kikawada, Takahiro; Okuda, Takashi

2015-06-01

Chironomid midges (Diptera; Chironomidae) are found in various environments from the high Arctic to the Antarctic, including temperate and tropical regions. In many freshwater habitats, members of this family are among the most abundant invertebrates. In the present study, the genome sizes of 25 chironomid species were determined by flow cytometry and the resulting C-values ranged from 0.07 to 0.20 pg DNA (i.e. from about 68 to 195 Mbp). These genome sizes were uniformly very small and included, to our knowledge, the smallest genome sizes recorded to date among insects. Small proportion of transposable elements and short intron sizes were suggested to contribute to the reduction of genome sizes in chironomids. We discuss about the possible developmental and physiological advantages of having a small genome size and about putative implications for the ecological success of the family Chironomidae.

The causal effect of board size in the performance of small and medium-sized firms

DEFF Research Database (Denmark)

Bennedsen, Morten; Kongsted, Hans Christian; Meisner Nielsen, Kasper

2008-01-01

correlation between family size and board size and show this correlation to be driven by firms where the CEO's relatives serve on the board. Second, we find empirical evidence of a small adverse board size effect driven by the minority of small and medium-sized firms that are characterized by having......Empirical studies of large publicly traded firms have shown a robust negative relationship between board size and firm performance. The evidence on small and medium-sized firms is less clear; we show that existing work has been incomplete in analyzing the causal relationship due to weak...... identification strategies. Using a rich data set of almost 7000 closely held corporations we provide a causal analysis of board size effects on firm performance: We use a novel instrument given by the number of children of the chief executive officer (CEO) of the firms. First, we find a strong positive...

On the Structure of Cortical Microcircuits Inferred from Small Sample Sizes.

Science.gov (United States)

Vegué, Marina; Perin, Rodrigo; Roxin, Alex

2017-08-30

The structure in cortical microcircuits deviates from what would be expected in a purely random network, which has been seen as evidence of clustering. To address this issue, we sought to reproduce the nonrandom features of cortical circuits by considering several distinct classes of network topology, including clustered networks, networks with distance-dependent connectivity, and those with broad degree distributions. To our surprise, we found that all of these qualitatively distinct topologies could account equally well for all reported nonrandom features despite being easily distinguishable from one another at the network level. This apparent paradox was a consequence of estimating network properties given only small sample sizes. In other words, networks that differ markedly in their global structure can look quite similar locally. This makes inferring network structure from small sample sizes, a necessity given the technical difficulty inherent in simultaneous intracellular recordings, problematic. We found that a network statistic called the sample degree correlation (SDC) overcomes this difficulty. The SDC depends only on parameters that can be estimated reliably given small sample sizes and is an accurate fingerprint of every topological family. We applied the SDC criterion to data from rat visual and somatosensory cortex and discovered that the connectivity was not consistent with any of these main topological classes. However, we were able to fit the experimental data with a more general network class, of which all previous topologies were special cases. The resulting network topology could be interpreted as a combination of physical spatial dependence and nonspatial, hierarchical clustering. SIGNIFICANCE STATEMENT The connectivity of cortical microcircuits exhibits features that are inconsistent with a simple random network. Here, we show that several classes of network models can account for this nonrandom structure despite qualitative differences in

Efficient and Reliable Solar Panels for Small CubeSat Picosatellites

Directory of Open Access Journals (Sweden)

Ivo Vertat

2014-01-01

Full Text Available CubeSat picosatellites have a limited area of walls for solar cells assembling and the available area has to be effectively shared with other parts, such as planar antennas, optical sensors, camera lens, and access port. With standard size of solar cell strings, it is not possible to construct a reliable solar panel for CubeSat with redundant strings interconnection. Typical solar panels for CubeSat consist of two solar cell strings serially wired with no redundancy in case of solar string failure. The loss of electric energy from one solar panel can cause a serious problem for most picosatellites due to minimum margin in the blueprints of the picosatellite subsystem power budget. In this paper, we propose a new architecture of solar panels for PilsenCUBE CubeSat with a high level of redundancy in the case of solar string failure or following switched power regulator failure. Our solar panels use a high efficiency triple junction GaInP2/GaAs/Ge in the form of small triangle strings from the Spectrolab Company. A suitable technology for precise solar cell assembling is also discussed, because CubeSat picosatellites are usually developed by small teams with limited access to high-end facilities.

On the Impacts of PV Array Sizing on the Inverter Reliability and Lifetime

DEFF Research Database (Denmark)

Sangwongwanich, Ariya; Yang, Yongheng; Sera, Dezso

2018-01-01

, the total energy yield can be increased under weak solar irradiance conditions. However, oversizing the PV array will increase the loading of PV inverters, which may have undesired influence on the PV inverter reliability and lifetime. In that case, it may result in a negative impact on the overall PV...... energy cost, due to the increased maintenance for the PV inverters. With the above concern, this paper evaluates the reliability and lifetime of PV inverters considering the PV array sizing. The evaluation is based on the mission profile of the installation sites in Denmark and Arizona, where...... the reliability-critical components such as power devices and capacitors are considered. The results reveal that the variation in the PV array sizing can considerably deviate the reliability performance and lifetime expectation of PV inverters, especially for those installed in Denmark, where the average solar...

Involvement of small and medium-sized enterprises (SMEs in elaborating and implementing public policies: Study case-Romanian small and medium-sized enterprises

Directory of Open Access Journals (Sweden)

Popescu Ruxandra

2017-07-01

Full Text Available Involvement and development of the private sector in boosting the economy nationwide is a main objective of the current program of the government, which means that a good cooperation between small and medium companies, private companies and multinationals and public environment including both public institutions and policies implemented and developed by them, becomes more than necessary. The paper summarizes the findings of a quantitative research based on a self-applied questionnaire which was aimed at Romanian small and medium-sized enterprises and also of a qualitative research that gives an overview of the process of elaborating and implementing a public policy. The involvement of small and medium-sized enterprises in the process of designing and implementing a public policy can become indispensable but it is well know that there is, in fact, a lack of initiative at this level, from both parties. One of the main research questions of this paper is to find out how much do representatives of small and medium-sized enterprises get involved in the process of elaborating a public policy and how much do these actions and measures impact the organizational policies of the companies themselves. A good cooperation between the business environment and the public institutions and a strong correlation of their joint efforts, should become a common practice between both parties, being crucial that this form of cooperation to be initiated from the very beginning. The contribution of this paper is a practical one, given the fact that the paper itself entails the direct responses of small and medium-sized enterprises on the current and future public policies that directly targets them, providing as well an analysis on the effects of public policies on small and medium-sized enterprises. Thus being said, the paper can also be a guide for both small and medium-sized enterprises in providing examples and measures of involvement and favorable public policies

On the application of the weak-beam technique to the determination of the sizes of small point-defect clusters in ion-irradiated copper

International Nuclear Information System (INIS)

Jenkins, M. L.

1998-01-01

We have made an analysis of the conditions necessary for the successful use of the weak-beam technique for identifying and characterizing small point-defect clusters in ion-irradiated copper. The visibility of small defects was found to depend only weakly on the magnitude of the beam-convergence. In general, the image sizes of small clusters were found to be most sensitive to the magnitude of Sa with the image sizes of some individual defects changing by large amounts with changes as small as 0.025 nm -1 . The most reliable information on the true defect size is likely to be obtained by taking a series of 5-9 micrographs with a systematic variation of deviation parameter from 0.2-0.3 nm -1 . This procedure allows size information to be obtained down to a resolution limit of about 0.5 nm for defects situated throughout a foil thickness of 60 nm. The technique has been applied to the determination of changes in the sizes of small defects produced by a low-temperature in-situ irradiation and annealing experiment

Increase of efficiency and reliability of liquid fuel combustion in small-sized boilers

Science.gov (United States)

Roslyakov, P. V.; Proskurin, Yu V.; Ionkin, I. L.

2017-11-01

One of the ways to increase the efficiency of using fuels is to create highly efficient domestic energy equipment, in particular small-sized hot-water boilers in autonomous heating systems. Increasing the efficiency of the boiler requires a reduction in the temperature of the flue gases leaving, which, in turn, can be achieved by installing additional heating surfaces. The purpose of this work was to determine the principal design solutions and to develop a draft design for a high-efficiency 3-MW hot-water boiler using crude oil as its main fuel. Ensuring a high efficiency of the boiler is realized through the use of an external remote economizer, which makes it possible to reduce the dimensions of the boiler, facilitate the layout of equipment in a limited size block-modular boiler house and virtually eliminate low-temperature corrosion of boiler heat exchange surfaces. In the article the variants of execution of the water boiler and remote economizer are considered and the preliminary design calculations of the remote economizer for various schemes of the boiler layout in the Boiler Designer software package are made. Based on the results of the studies, a scheme was chosen with a three-way boiler and a two-way remote economizer. The design of a three-way fire tube hot water boiler and an external economizer with an internal arrangement of the collectors, providing for its location above the boiler in a block-modular boiler house and providing access for servicing both a remote economizer and a hot water boiler, is proposed. Its mass-dimensional and design parameters are determined. In the software package Boiler Designer thermal, hydraulic and aerodynamic calculations of the developed fire tube boiler have been performed. Optimization of the boiler design was performed, providing the required 94% efficiency value for crude oil combustion. The description of the developed flue and fire-tube hot water boiler and the value of the main design and technical and

76 FR 14323 - Small Business Size Standards: Professional, Scientific and Technical Services

Science.gov (United States)

2011-03-16

... government small business assistance programs, SBA establishes small business size definitions (referred to... its field of operation and (3) within a specific small business definition or size standard... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG07 Small Business Size Standards...

Trade-offs in size, quantity and reliability of generalized nuclear power plants: a preliminary assessment

International Nuclear Information System (INIS)

Hill, D.

1985-04-01

An approximate method is used to estimate the effects of system reliability on optimal nuclear plant size, taking into account also scale factors and manufacturing learning curve slopes. The method is used to estimate the additional effective capability gained by adding units of different sizes to an existing electrical system. The number of additional units proves to be sensitive to forced outrage rate, estimated here from trends in US light-water reactors from 1971 to 1980. The relative cost of added units ranging in size from 200 to 800 MW is determined as a function of the parameters: scale factor and learning curve slope. The results generally corrobate the trends found in an earlier study in which the effect of reliability on required installed capacity was not explicitly considered. Optimal plant size decreases with weaker scale effects and stronger learning curve effects. Reliability considerations further reduce the optimal plant size, but the relative reduction is apparently not as great with steeper learning curves. This is a plausible finding inasmuch as the reduction in numbers of additional units due to reliability considerations will affect cost most where the learning curve is steepest. 9 refs., 4 figs., 3 tabs

Development of small-size baking oven

Energy Technology Data Exchange (ETDEWEB)

Tabata, Akihisa; Kuwabara, Shigeru; Yamazawa, Yoshitaka; Shigeta, Eiji

1987-03-01

In the bakery business, oven fresh bakeries selling fresh bread by installing their own baking ovens at their shops have become popular recently. This article reports the development of a small-size gas baking oven for oven fresh bakaries. The gas convection oven developed recently is based on the structure of the conventional electric convection oven, and uses low pressure gas. The gas oven has an advantage that the combustion gas contains moisture. The convection oven bakes bread normally at the baking density approximately 2.5 times as much as that of the radiation oven, thereby the size of the oven may become smaller. This oven can bake many kinds of bread ranging from croissants to bean-jam buns by gas combnstion heat as well as radiation heat from the radiation plates installed at the top of each compartment in the oven. An ultra small air heat type burner was developed to provide stable short flames in order to make the size of the combustion chamber smaller. (20 figs, 2 tabs)

The value chain of small-sized energy wood

Energy Technology Data Exchange (ETDEWEB)

Karttunen, K.; Foehr, J.; Ranta, T. (Lappeenranta Univ. of Technology, Mikkeli (Finland), LUT Energy), Email: kalle.karttunen@lut.fi, Email: jarno.fohr@lut.fi, Email: tapio.ranta@lut.fi; Ahtikoski, A. (The Finnish Forest Research Institute, Rovaniemi (Finland)), Email: anssi.ahtikoski@metla.fi; Valsta, L. (Helsinki Univ. (Finland), Dept. of Forest Economics), Email: lauri.valsta@helsinki.fi

2009-07-01

Finland has agreed to increase the share of renewable energy to the level of 38% by the end of 2020. Most of the increase is to be based on bioenergy. According to the National Climate and Energy Strategy, the need for forest biomass will come to more than 20 TWh, or some 10 million cubic meters per year. Energy wood from young stand thinnings are the biomass resource with the most potential at the moment. The purpose of this study was to compare cost differences between forest management incorporating energy wood thinning and forest management based on traditional roundwood thinning. In addition, alternative supply chain costs for small-sized wood were studied. The results of the study show that it is worth considering the following points if the demand and average price for forest chips remain high. 1. Forest-owners: Forest management including energy wood thinning is financially feasible. 2. Supply chain: A terminal chipping chain enables large-scale procurement of small-sized energy wood. 3. Power plants: Currently, subsidies, emission trading, and decreasing pulpwood prices together enable large-scale use of small-sized wood for energy purposes. The value chain of small-sized energy wood in large-scale power plants could be mobilised. (orig.)

Information Security in Small and Medium-Sized Companies

OpenAIRE

David Kral

2011-01-01

Information security doesn’t involve only large organizations. Small and medium-sized companies must closely examine this issue too, because they are increasingly threatened by cyber attacks. Many of them mistakenly believe, that security of their valuable data is sufficient, or that the attackers are not interested in them. Existing standards and methodologies for implementation and management of information security are often hard to transfer to the environment of small and medium-sized bus...

78 FR 37404 - Small Business Size Standards: Support Activities for Mining

Science.gov (United States)

2013-06-20

... assistance programs, SBA establishes small business size definitions (referred to as size standards) for... million should be the limit of a small business definition and anything larger than that, such as that SBA... Business Act (15 U.S.C. 632(a)) (Act) requires that small business size definitions vary to reflect...

77 FR 72766 - Small Business Size Standards: Support Activities for Mining

Science.gov (United States)

2012-12-06

... eligibility for Federal small business assistance, SBA establishes small business size definitions (referred... operation; and (3) within a specific small business definition or size standard established by SBA... to SBA's Administrator the responsibility for establishing small business definitions. The Act also...

Photographic assessment of burn size and depth: reliability and validity

NARCIS (Netherlands)

Hop, M.; Moues, C.; Bogomolova, K.; Nieuwenhuis, M.; Oen, I.; Middelkoop, E.; Breederveld, R.; de Baar, M.

2014-01-01

Objective: The aim of this study was to examine the reliability and validity of using photographs of burns to assess both burn size and depth. Method: Fifty randomly selected photographs taken on day 0-1 post burn were assessed by seven burn experts and eight referring physicians. Inter-rater

Prognosis method to predict small-sized breast cancer affected by fibrocystic disease

Directory of Open Access Journals (Sweden)

S. A. Velichko

2017-01-01

Full Text Available The purpose of the study is to develop an effective radiological symptom-complex of small-sized breast cancer affected by fibrocystic breast disease by using multivariate statistical methods.Materials and methods. Radiological findings of small-sized breast cancer affected by fibrocystic mastopathy were analyzed in 100 patients with histologically verified diagnosis.Results. It was revealed that the conventional approach to the analysis of mammograms based on the detection of the primary, secondary and indirect mammographic signs of small-sized breast cancer is not effective enough - the sensitivity of mammography is only 62%. Fibrocystic disease and moderate-to-severe sclerosing adenosis make small-sized breast cancer hard to visualize by mammography. The detailed analysis of mammograms allowed us to identify the additional manifestations of small-sized breast cancer affected by mastopathy. The computer program allowing us to evaluate the risk of small-size breast cancer and the diagnostic algorithm for detecting small size breast cancer with sensitivity of 92% were developed. 

Small-size biofuel cell on paper.

Science.gov (United States)

Zhang, Lingling; Zhou, Ming; Wen, Dan; Bai, Lu; Lou, Baohua; Dong, Shaojun

2012-05-15

In this work, we demonstrated a novel paper-based mediator-less and compartment-less biofuel cell (BFC) with small size (1.5 cm × 1.5 cm). Ionic liquid functionalized carbon nanotubes (CNTs-IL) nanocomposite was used as support for both stably confining the anodic biocatalyst (i.e., NAD(+)-dependent glucose dehydrogenase, GDH) for glucose electrooxidation and for facilitating direct electrochemistry of the cathodic biocatalyst (i.e., bilirubin oxidase, BOD) for O(2) electroreduction. Such BFC provided a simple approach to fabricate low-cost and portable power devices on small-size paper, which can harvest energy from a wide range of commercial beverages containing glucose (e.g., Nescafe instant coffee, Maidong vitamin water, Watermelon fresh juice, and Minute Maid grape juice). These made the low-cost paper-based biodevice potential for broad energy applications. Copyright © 2012 Elsevier B.V. All rights reserved.

Examination on small-sized cogeneration HTGR for developing countries

International Nuclear Information System (INIS)

Sakaba, Nariaki; Tachibana, Yukio; Shimakawa, Satoshi; Ohashi, Hirofumi; Sato, Hiroyuki; Yan, Xing; Murakami, Tomoyuki; Ohashi, Kazutaka; Nakagawa, Shigeaki; Goto, Minoru; Ueta, Shohei; Mozumi, Yasuhiro; Imai, Yoshiyuki; Tanaka, Nobuyuki; Okuda, Hiroyuki; Iwatsuki, Jin; Kubo, Shinji; Takada, Shoji; Nishihara, Tetsuo; Kunitomi, Kazuhiko

2008-03-01

The small-sized and safe cogeneration High Temperature Gas-cooled Reactor (HTGR) that can be used not only for electric power generation but also for hydrogen production and district heating is considered one of the most promising nuclear reactors for developing countries where sufficient infrastructure such as power grids is not provided. Thus, the small-sized cogeneration HTGR, named High Temperature Reactor 50-Cogeneration (HTR50C), was studied assuming that it should be constructed in developing countries. Specification, equipment configuration, etc. of the HTR50C were determined, and economical evaluation was made. As a result, it was shown that the HTR50C is economically competitive with small-sized light water reactors. (author)

75 FR 61597 - Small Business Size Standards: Retail Trade

Science.gov (United States)

2010-10-06

... eligibility for Federal small business assistance programs, SBA establishes small business size definitions... authorizes the SBA Administrator to establish only one definition of small business for an industry. [[Page... SBA's Administrator the responsibility for establishing small business definitions. The Act also...

77 FR 42211 - Small Business Size Standards: Arts, Entertainment, and Recreation

Science.gov (United States)

2012-07-18

..., SBA establishes small business definitions (referred to as size standards) for private sector... operated; (2) not dominant in its field of operation; and (3) within a specific small business definition... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG36 Small Business Size Standards: Arts...

Sample size planning for composite reliability coefficients: accuracy in parameter estimation via narrow confidence intervals.

Science.gov (United States)

Terry, Leann; Kelley, Ken

2012-11-01

Composite measures play an important role in psychology and related disciplines. Composite measures almost always have error. Correspondingly, it is important to understand the reliability of the scores from any particular composite measure. However, the point estimates of the reliability of composite measures are fallible and thus all such point estimates should be accompanied by a confidence interval. When confidence intervals are wide, there is much uncertainty in the population value of the reliability coefficient. Given the importance of reporting confidence intervals for estimates of reliability, coupled with the undesirability of wide confidence intervals, we develop methods that allow researchers to plan sample size in order to obtain narrow confidence intervals for population reliability coefficients. We first discuss composite reliability coefficients and then provide a discussion on confidence interval formation for the corresponding population value. Using the accuracy in parameter estimation approach, we develop two methods to obtain accurate estimates of reliability by planning sample size. The first method provides a way to plan sample size so that the expected confidence interval width for the population reliability coefficient is sufficiently narrow. The second method ensures that the confidence interval width will be sufficiently narrow with some desired degree of assurance (e.g., 99% assurance that the 95% confidence interval for the population reliability coefficient will be less than W units wide). The effectiveness of our methods was verified with Monte Carlo simulation studies. We demonstrate how to easily implement the methods with easy-to-use and freely available software. ©2011 The British Psychological Society.

Evaluation of fracture toughness of vessel materials using small-size specimens and full stress-strain curves

Energy Technology Data Exchange (ETDEWEB)

Lebedev, A A; Chausov, N G [Akademyiya Nauk Ukrayini, Kiev (Ukraine)

1994-12-31

Physically substantiated dependences between crack resistance characteristics determined by the parameters of descending sections of full stress-strain curves and stressed state rigidity at crack initiation moment, have been experimentally obtained. The possibility of crack resistance reliable estimation based on full stress-strain obtained using small-size specimens with different concentrators, has thus been experimentally substantiated. Results obtained by the method and actual temperature dependence of irradiated steel 15X2NMFA crack resistance characteristics, agreed well. 2 refs., 7 figs.

75 FR 1296 - Small Business Size Regulations; 8(a) Business Development/Small Disadvantaged Business Status...

Science.gov (United States)

2010-01-11

... SMALL BUSINESS ADMINISTRATION 13 CFR Parts 121 and 124 Small Business Size Regulations; 8(a) Business Development/Small Disadvantaged Business Status Determinations AGENCY: U.S. Small Business Administration. ACTION: Notice of public meetings; request for comments. SUMMARY: The U.S. Small Business...

78 FR 38811 - Small Business Size and Status Integrity

Science.gov (United States)

2013-06-28

.... Firms will not be able submit offers for small business contracts based on their online representations... SMALL BUSINESS ADMINISTRATION 13 CFR Parts 121, 124, 125, 126, and 127 RIN 3245-AG23 Small Business Size and Status Integrity AGENCY: Small Business Administration. ACTION: Final rule. SUMMARY: This...

Small and medium-sized nuclear power plants

International Nuclear Information System (INIS)

Schmidt, R.

1986-01-01

Small and medium-sized nuclear power plants have long been under discussion as possible applications of nuclear power in countries with small transmission grid systems, in threshold countries and developing countries, and under special local supply conditions. IAEA has condensed and promoted this interest and tried to establish the demand, and possibilities of meeting it, in special events and campaigns. In recent years, considerable interest was registered even in industrialized countries, but here specially for heating and process heat generation applications and for special purposes and, in medium-sized units, also for combined supplies of electricity and heat. This corresponds to special reactor and plant concepts, some of which have already been developed to a stage at which construction work could begin. The analysis presented deals with necessary preconditions on the sides of the users and the vendors, with problems of economy, infrastructure and financing and with the market prospects of small nuclear power plants. (orig./HP) [de

Bank Size and Small- and Medium-sized Enterprise (SME) Lending: Evidence from China

Science.gov (United States)

SHEN, YAN; SHEN, MINGGAO; XU, ZHONG; BAI, YING

2014-01-01

Summary Using panel data collected in 2005, we evaluate how bank size, discretion over credit, incentive schemes, competition, and the institutional environment affect lending to small- and medium-sized enterprises in China. We deal with the endogeneity problem using instrumental variables, and a reduced-form approach is also applied to allow for weak instruments in estimation. We find that total bank asset is an insignificant factor for banks’ decision on small- and medium-enterprise (SME) lending, but more local lending authority, more competition, carefully designed incentive schemes, and stronger law enforcement encourage commercial banks to lend to SMEs. PMID:26052179

Bank Size and Small- and Medium-sized Enterprise (SME) Lending: Evidence from China.

Science.gov (United States)

Shen, Yan; Shen, Minggao; Xu, Zhong; Bai, Ying

2009-04-01

Using panel data collected in 2005, we evaluate how bank size, discretion over credit, incentive schemes, competition, and the institutional environment affect lending to small- and medium-sized enterprises in China. We deal with the endogeneity problem using instrumental variables, and a reduced-form approach is also applied to allow for weak instruments in estimation. We find that total bank asset is an insignificant factor for banks' decision on small- and medium-enterprise (SME) lending, but more local lending authority, more competition, carefully designed incentive schemes, and stronger law enforcement encourage commercial banks to lend to SMEs.

Internationalization of small and medium-sized enterprises

Directory of Open Access Journals (Sweden)

Zoran Paunović

2010-06-01

Full Text Available Highly developed countries, which are similar to Croatia by size and population, highlight the importance of small and medium-sized enterprises (SMEs as holders of export activities and key factors in raising the competitiveness of the entire economy. In this paper authors research the concept of internationalization of SMEs. Analyzing the influence of decision makers on the process of internationalization and showing its advantages and disadvantages for the respective company and country, this research introduces the most common models on the basis of which this process is implemented in practice. A case study of a small export company from Croatia illustrates the process of internationalization to the U.S. market and provides useful information to the companies which are planning to enter new markets.

Decision Support on Small size Passive Samples

Directory of Open Access Journals (Sweden)

Vladimir Popukaylo

2018-05-01

Full Text Available A construction technique of adequate mathematical models for small size passive samples, in conditions when classical probabilistic-statis\\-tical methods do not allow obtaining valid conclusions was developed.

Reliable calculation in probabilistic logic: Accounting for small sample size and model uncertainty

Energy Technology Data Exchange (ETDEWEB)

Ferson, S. [Applied Biomathematics, Setauket, NY (United States)

1996-12-31

A variety of practical computational problems arise in risk and safety assessments, forensic statistics and decision analyses in which the probability of some event or proposition E is to be estimated from the probabilities of a finite list of related subevents or propositions F,G,H,.... In practice, the analyst`s knowledge may be incomplete in two ways. First, the probabilities of the subevents may be imprecisely known from statistical estimations, perhaps based on very small sample sizes. Second, relationships among the subevents may be known imprecisely. For instance, there may be only limited information about their stochastic dependencies. Representing probability estimates as interval ranges on has been suggested as a way to address the first source of imprecision. A suite of AND, OR and NOT operators defined with reference to the classical Frochet inequalities permit these probability intervals to be used in calculations that address the second source of imprecision, in many cases, in a best possible way. Using statistical confidence intervals as inputs unravels the closure properties of this approach however, requiring that probability estimates be characterized by a nested stack of intervals for all possible levels of statistical confidence, from a point estimate (0% confidence) to the entire unit interval (100% confidence). The corresponding logical operations implied by convolutive application of the logical operators for every possible pair of confidence intervals reduces by symmetry to a manageably simple level-wise iteration. The resulting calculus can be implemented in software that allows users to compute comprehensive and often level-wise best possible bounds on probabilities for logical functions of events.

76 FR 70680 - Small Business Size Standards: Real Estate and Rental and Leasing

Science.gov (United States)

2011-11-15

... eligibility for Federal small business assistance, SBA establishes small business size definitions (referred... business definition or size standard established by the SBA Administrator. SBA considers as part of its... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG28 Small Business Size Standards: Real...

77 FR 76215 - Small Business Size Regulations, Small Business Innovation Research (SBIR) Program and Small...

Science.gov (United States)

2012-12-27

... overall goal of simplification and maximization of benefits for small businesses, SBA proposed amendments... franchisee. F. Section 121.704--When SBA Determines Size and Eligibility SBA's proposed regulations for the...

76 FR 8221 - Small Business Size Regulations; 8(a) Business Development/Small Disadvantaged Business Status...

Science.gov (United States)

2011-02-11

... Vol. 76 Friday, No. 29 February 11, 2011 Part VII Small Business Administration 13 CFR Parts 121 and 124 Small Business Size Regulations; 8(a) Business Development/Small Disadvantaged Business Status... Regulations#0;#0; [[Page 8222

Reliability of different mark-recapture methods for population size estimation tested against reference population sizes constructed from field data.

Directory of Open Access Journals (Sweden)

Annegret Grimm

Full Text Available Reliable estimates of population size are fundamental in many ecological studies and biodiversity conservation. Selecting appropriate methods to estimate abundance is often very difficult, especially if data are scarce. Most studies concerning the reliability of different estimators used simulation data based on assumptions about capture variability that do not necessarily reflect conditions in natural populations. Here, we used data from an intensively studied closed population of the arboreal gecko Gehyra variegata to construct reference population sizes for assessing twelve different population size estimators in terms of bias, precision, accuracy, and their 95%-confidence intervals. Two of the reference populations reflect natural biological entities, whereas the other reference populations reflect artificial subsets of the population. Since individual heterogeneity was assumed, we tested modifications of the Lincoln-Petersen estimator, a set of models in programs MARK and CARE-2, and a truncated geometric distribution. Ranking of methods was similar across criteria. Models accounting for individual heterogeneity performed best in all assessment criteria. For populations from heterogeneous habitats without obvious covariates explaining individual heterogeneity, we recommend using the moment estimator or the interpolated jackknife estimator (both implemented in CAPTURE/MARK. If data for capture frequencies are substantial, we recommend the sample coverage or the estimating equation (both models implemented in CARE-2. Depending on the distribution of catchabilities, our proposed multiple Lincoln-Petersen and a truncated geometric distribution obtained comparably good results. The former usually resulted in a minimum population size and the latter can be recommended when there is a long tail of low capture probabilities. Models with covariates and mixture models performed poorly. Our approach identified suitable methods and extended options to

77 FR 11001 - Small Business Size Standards: Health Care and Social Assistance

Science.gov (United States)

2012-02-24

..., and (3) within a specific small business definition or size standard established by the SBA... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG30 Small Business Size Standards: Health Care and Social Assistance AGENCY: U.S. Small Business Administration. ACTION: Proposed rule. SUMMARY...

77 FR 55755 - Small Business Size Standards: Agriculture, Forestry, Fishing, and Hunting

Science.gov (United States)

2012-09-11

... operation; and (3) within a specific small business definition or size standard established by SBA... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG43 Small Business Size Standards: Agriculture, Forestry, Fishing, and Hunting AGENCY: U.S. Small Business Administration. ACTION: Proposed rule...

76 FR 27952 - Small Business Size Standards: Professional, Scientific and Technical Services.

Science.gov (United States)

2011-05-13

... Administration (SBA or Agency) proposed to increase small business size standards for 35 industries and one sub... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG07 Small Business Size Standards: Professional, Scientific and Technical Services. AGENCY: U.S. Small Business Administration. ACTION: Proposed...

Human Reliability Analysis for Small Modular Reactors

Energy Technology Data Exchange (ETDEWEB)

Ronald L. Boring; David I. Gertman

2012-06-01

Because no human reliability analysis (HRA) method was specifically developed for small modular reactors (SMRs), the application of any current HRA method to SMRs represents tradeoffs. A first- generation HRA method like THERP provides clearly defined activity types, but these activity types do not map to the human-system interface or concept of operations confronting SMR operators. A second- generation HRA method like ATHEANA is flexible enough to be used for SMR applications, but there is currently insufficient guidance for the analyst, requiring considerably more first-of-a-kind analyses and extensive SMR expertise in order to complete a quality HRA. Although no current HRA method is optimized to SMRs, it is possible to use existing HRA methods to identify errors, incorporate them as human failure events in the probabilistic risk assessment (PRA), and quantify them. In this paper, we provided preliminary guidance to assist the human reliability analyst and reviewer in understanding how to apply current HRA methods to the domain of SMRs. While it is possible to perform a satisfactory HRA using existing HRA methods, ultimately it is desirable to formally incorporate SMR considerations into the methods. This may require the development of new HRA methods. More practicably, existing methods need to be adapted to incorporate SMRs. Such adaptations may take the form of guidance on the complex mapping between conventional light water reactors and small modular reactors. While many behaviors and activities are shared between current plants and SMRs, the methods must adapt if they are to perform a valid and accurate analysis of plant personnel performance in SMRs.

78 FR 45051 - Small Business Size Standards; Support Activities for Mining; Correction

Science.gov (United States)

2013-07-26

... Regulations by increasing small business size standards for three of the four industries in North American... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG44 Small Business Size Standards; Support Activities for Mining; Correction AGENCY: U.S. Small Business Administration. ACTION: Final rule; correction...

Small renal size in newborns with spina bifida: possible causes.

Science.gov (United States)

Montaldo, Paolo; Montaldo, Luisa; Iossa, Azzurra Concetta; Cennamo, Marina; Caredda, Elisabetta; Del Gado, Roberto

2014-02-01

Previous studies reported that children with neural tube defects, but without any history of intrinsic renal diseases, have small kidneys when compared with age-matched standard renal growth. The aim of this study was to investigate the possible causes of small renal size in children with spina bifida by comparing growth hormone deficiency, physical limitations and hyperhomocysteinemia. The sample included 187 newborns with spina bifida. Renal sizes in the patients were assessed by using maximum measurement of renal length and the measurements were compared by using the Sutherland monogram. According to the results, the sample was divided into two groups--a group of 120 patients with small kidneys (under the third percentile) and a control group of 67 newborns with normal kidney size. Plasma total homocysteine was investigated in mothers and in their children. Serum insulin-like growth factor-1 (IGF-1) levels were measured. Serum IGF-1 levels were normal in both groups. Children and mothers with homocysteine levels >10 μmol/l were more than twice as likely to have small kidneys and to give to birth children with small kidneys, respectively, compared with newborns and mothers with homocysteine levels <10 μmol/l. An inverse correlation was also found between the homocysteine levels of mothers and kidney sizes of children (r = - 0.6109 P ≤ 0.01). It is highly important for mothers with hyperhomocysteinemia to be educated about benefits of folate supplementation in order to reduce the risk of small renal size and lower renal function in children.

Reliability and Validity of the Activity Participation Assessment for School-age Children in Korea

Directory of Open Access Journals (Sweden)

Se-Yun Kim

2016-12-01

Conclusion: The APA shows good internal reliability, test–retest reliability, discriminant validity, and construct validity. However, evidence of psychometric properties was limited by a small sample size. Psychometric properties such as interrater reliability as well as concurrent validity and construct validity need to be tested using a larger sample size with representative demographics.

75 FR 61604 - Small Business Size Standards; Accommodation and Food Services Industries

Science.gov (United States)

2010-10-06

... business assistance programs, SBA establishes small business size definitions (referred to as size... Administrator the responsibility for establishing small business definitions. The Act also requires that small business definitions vary to reflect industry differences. The supplementary information section of this...

Small-Size High-Current Generators for X-Ray Backlighting

Science.gov (United States)

Chaikovsky, S. A.; Artyomov, A. P.; Zharova, N. V.; Zhigalin, A. S.; Lavrinovich, I. V.; Oreshkin, V. I.; Ratakhin, N. A.; Rousskikh, A. G.; Fedunin, A. V.; Fedushchak, V. F.; Erfort, A. A.

2017-12-01

The paper deals with the soft X-ray backlighting based on the X-pinch as a powerful tool for physical studies of fast processes. Proposed are the unique small-size pulsed power generators operating as a low-inductance capacitor bank. These pulse generators provide the X-pinch-based soft X-ray source (hν = 1-10 keV) of micron size at 2-3 ns pulse duration. The small size and weight of pulse generators allow them to be transported to any laboratory for conducting X-ray backlighting of test objects with micron space resolution and nanosecond exposure time. These generators also allow creating synchronized multi-frame radiographic complexes with frame delay variation in a broad range.

Prognostic Importance of Small Prostate Size in Men Receiving Definitive Prostate Brachytherapy

International Nuclear Information System (INIS)

Taira, Al V.; Merrick, Gregory S.; Galbreath, Robert W.; Butler, Wayne M.; Adamovich, Edward; Wallner, Kent E.

2012-01-01

Purpose: To assess whether small prostate size is an adverse prognostic factor in men undergoing brachytherapy in the same manner in which it seems to be for men undergoing radical prostatectomy. Methods and Materials: From April 1995 to June 2008, 2024 patients underwent brachytherapy by a single brachytherapist. Median follow-up was 7.4 years. The role of small prostate size (≤20 cm 3 ) as a prognostic factor for biochemical progression-free survival, cause-specific survival, and all-cause mortality was investigated. The differences in survival between men with small and larger prostates were compared using Kaplan-Meier curves and log-rank tests. Results: Median prostate size for the entire cohort was 32.7 cm 3 . For the 167 men with small prostates, median prostate size was 17.4 cm 3 . There was no difference in biochemical progression-free survival (95.2% vs 96.2%, P=.603), cause-specific survival (97.7% vs 98.3%, P=.546), or all-cause mortality (78.0% vs 77.2%, P=.838) at 10 years for men with small prostates compared with men with larger prostates. On univariate and multivariate analysis, small prostate size was not associated with any of the primary outcome measures. Conclusion: Men with small prostates treated with brachytherapy have excellent outcomes and are at no higher risk of treatment failure than men with larger glands. High-quality implants with adequate margins seem sufficient to address the increased adverse risk factors associated with small prostate size.

GOVERNMENT SUPPORT FOR SMALL AND MEDIUM-SIZED BUSINESS AND INNOVATIVE ACTIVITIES

Directory of Open Access Journals (Sweden)

Pоlina Kolisnichenko

2017-09-01

Full Text Available The purpose of the paper is to reveal the conditions of the innovative development of the small and mediumsized entrepreneurship in Ukraine; the problems that suppress the innovative activity and small and medium-sized enterprises development; peculiarities of the tax incentives for the development of the entrepreneurship in the advanced countries and in Ukraine; the main kinds and characteristics of the small and medium-sized enterprises public support. Methodology. The methods of scientific research include: analysis and generalization for studying the main kinds and characteristics of the government support of the small and medium-sized enterprises; dynamic and comparative analysis for studying the problems and factors influencing the development of small and medium enterprises and innovative activity, peculiarities of tax incentives for business development; systemanalytical method for studying the conditions of the innovative development of the small and medium-sized entrepreneurship. Results. The government's financial support priorities should be: optimal application of the fiscal regulation instruments (reduction of the amount of taxes, determination of the criteria for the maximum taxation amount, tax incentives etc., maintenance of the self-investment of small and medium-sized enterprises as well as investment, financial means of the public influence over the development of the enterprises, effective combination of both direct and indirect forms of the innovative development support. Practical implications. The obtained results can be used in the process of formation and implementation of the small and medium enterprise sector development strategy and innovative activity in the long-term perspective. Value/originality. The obtained data can provide a better understanding of the direction of innovative business development in Ukraine.

Challenges and Considerations for Innovative Small and Medium Sized Reactors

International Nuclear Information System (INIS)

Kuznetsov, V.

2008-01-01

There is an ongoing interest in Member States in the development and application of small and medium sized reactors (SMRs). In the near term, most new NPPs are likely to be evolutionary water cooled reactor designs building on proven systems while incorporating technological advances and often the economics of scale, resulting from the reactor outputs of up to 1600 MW(e). For a longer term, the focus is on innovative designs aiming to provide increased benefits in the areas of safety and security, non-proliferation, waste management, resource utilization and economy, as well as to offer a variety of energy products and flexibility in design, siting and fuel cycle options. Many innovative designs are reactors within the SMR range, having an equivalent electric power less than 700 MW(e) or even less than 300 MW(e). It is important that small or medium sized reactor does not necessarily mean small or medium sized nuclear power plant. The majority of innovative SMR concepts and designs provide for power station configurations with several units at a site or for NPP configurations with 2 or more reactor modules. In most cases, the units or modules could be added incrementally. Innovative SMRs are in many cases intended for markets different from those in which large nuclear power plants operate, i.e., markets that value more distributed electrical supplies, a better match between supply increments and investment capability or demand growth, more flexible siting or greater product variety. SMRs cannot compete with larger capacity plants on an economy of scale basis. However, they could be competitive via employing alternative design strategies, taking advantage of smaller reactor size resulting in a less complex design and operation and maintenance or in an increased overall energy conversion efficiency, and by relying on alternative deployment strategies, taking advantage of multiple unit factors and learning curve, and shorter construction schedule and 'exact' unit

78 FR 37397 - Small Business Size Standards: Agriculture, Forestry, Fishing and Hunting

Science.gov (United States)

2013-06-20

... responsibility for establishing small business size definitions (15 U.S.C. 632(a)). The Act also requires that small business size definitions vary to reflect industry differences. The Jobs Act requires the... definition, after consultation with the Office of Advocacy of the U.S. Small Business Administration (5 U.S.C...

Quality and reliability assurance of electronic components in small-scale and middle-sized plants

International Nuclear Information System (INIS)

Becker, P.

1982-01-01

Electronic components are forever finding their way into new fields of application and have an ever increasing influence on the quality and reliability of the products in which they are used. The user has very negligible influence on the production methods used for the manufacture of the components and the element properties. (orig.) [de

Reliable pipeline repair system for very large pipe size

Energy Technology Data Exchange (ETDEWEB)

Charalambides, John N.; Sousa, Alexandre Barreto de [Oceaneering International, Inc., Houston, TX (United States)

2004-07-01

The oil and gas industry worldwide has been mainly depending on the long-term reliability of rigid pipelines to ensure the transportation of hydrocarbons, crude oil, gas, fuel, etc. Many other methods are also utilized onshore and offshore (e.g. flexible lines, FPSO's, etc.), but when it comes to the underwater transportation of very high volumes of oil and gas, the industry commonly uses large size rigid pipelines (i.e. steel pipes). Oil and gas operators learned to depend on the long-lasting integrity of these very large pipelines and many times they forget or disregard that even steel pipelines degrade over time and more often that that, they are also susceptible to various forms of damage (minor or major, environmental or external, etc.). Over the recent years the industry had recognized the need of implementing an 'emergency repair plan' to account for such unforeseen events and the oil and gas operators have become 'smarter' by being 'pro-active' in order to ensure 'flow assurance'. When we consider very large diameter steel pipelines such as 42' and 48' nominal pipe size (NPS), the industry worldwide does not provide 'ready-made', 'off-the-shelf' repair hardware that can be easily shipped to the offshore location and effect a major repair within acceptable time frames and avoid substantial profit losses due to 'down-time' in production. The typical time required to establish a solid repair system for large pipe diameters could be as long as six or more months (depending on the availability of raw materials). This paper will present in detail the Emergency Pipeline Repair Systems (EPRS) that Oceaneering successfully designed, manufactured, tested and provided to two major oil and gas operators, located in two different continents (Gulf of Mexico, U.S.A. and Arabian Gulf, U.A.E.), for two different very large pipe sizes (42'' and 48'' Nominal Pipe Sizes

GOVERNMENT SUPPORT FOR SMALL AND MEDIUM-SIZED BUSINESS AND INNOVATIVE ACTIVITIES

OpenAIRE

Pоlina Kolisnichenko

2017-01-01

The purpose of the paper is to reveal the conditions of the innovative development of the small and mediumsized entrepreneurship in Ukraine; the problems that suppress the innovative activity and small and medium-sized enterprises development; peculiarities of the tax incentives for the development of the entrepreneurship in the advanced countries and in Ukraine; the main kinds and characteristics of the small and medium-sized enterprises public support. Methodology. The methods of scientific...

New Atrophic Acne Scar Classification: Reliability of Assessments Based on Size, Shape, and Number.

Science.gov (United States)

Kang, Sewon; Lozada, Vicente Torres; Bettoli, Vincenzo; Tan, Jerry; Rueda, Maria Jose; Layton, Alison; Petit, Lauren; Dréno, Brigitte

2016-06-01

consecutive sessions (P<.001 and P=0.4, respectively). Analysis showed only 65% of scars were identical in both sessions. We also found that there is a threshold of detection in terms of size, with poor agreement among investigators for very small scars (<2 mm). The repeatability of identification of scars ≥ 2.0 mm was acceptable, and we found that increasing scar size was positively correlated with agreement. Reliability was improved when only scars >2 mm were included. For smaller scars (<2 mm), inter-rater reliability was poor. While intuitively it makes sense that describing scar morphology could guide treatment, we have shown that shape-based evaluations are subjective and do not readily yield strong agreement. Until there is a more objective way to evaluate morphology that is readily available to practicing clinicians, we propose that size should be considered a primary characteristic for scar classification systems. We further suggest classification of <2 mm, 2-4 mm, and >4 mm based on how the size would likely affect diagnostic and therapeutic choices. Finally, we recommend that scars <2 mm not be included in a clinical classification but should be evaluated by an objective method that may be refined in the future. J Drugs Dermatol. 2016;15(6):693-702.

Management of small and medium size enterprises as a carrier of economic growth

Directory of Open Access Journals (Sweden)

Ožegović Lazar

2012-01-01

Full Text Available Numerous studies in the world of market economy show that the share of small and medium size enterprises is constantly increasing compared to large enterprises. This does not decrease the significance of large enterprises, but the dependence between them gets larger every day. National economies which manage to find the optimal combination between small, medium size and large enterprises are more successful than the others. Management of small and medium size enterprises (SMEs in conceptual terms is similar to the process of management of large enterprises. An organization must be managed in order to function and this rule applies to small and medium size enterprises.

Optimal integrated sizing and planning of hubs with midsize/large CHP units considering reliability of supply

International Nuclear Information System (INIS)

Moradi, Saeed; Ghaffarpour, Reza; Ranjbar, Ali Mohammad; Mozaffari, Babak

2017-01-01

Highlights: • New hub planning formulation is proposed to exploit assets of midsize/large CHPs. • Linearization approaches are proposed for two-variable nonlinear CHP fuel function. • Efficient operation of addressed CHPs & hub devices at contingencies are considered. • Reliability-embedded integrated planning & sizing is formulated as one single MILP. • Noticeable results for costs & reliability-embedded planning due to mid/large CHPs. - Abstract: Use of multi-carrier energy systems and the energy hub concept has recently been a widespread trend worldwide. However, most of the related researches specialize in CHP systems with constant electricity/heat ratios and linear operating characteristics. In this paper, integrated energy hub planning and sizing is developed for the energy systems with mid-scale and large-scale CHP units, by taking their wide operating range into consideration. The proposed formulation is aimed at taking the best use of the beneficial degrees of freedom associated with these units for decreasing total costs and increasing reliability. High-accuracy piecewise linearization techniques with approximation errors of about 1% are introduced for the nonlinear two-dimensional CHP input-output function, making it possible to successfully integrate the CHP sizing. Efficient operation of CHP and the hub at contingencies is extracted via a new formulation, which is developed to be incorporated to the planning and sizing problem. Optimal operation, planning, sizing and contingency operation of hub components are integrated and formulated as a single comprehensive MILP problem. Results on a case study with midsize CHPs reveal a 33% reduction in total costs, and it is demonstrated that the proposed formulation ceases the need for additional components/capacities for increasing reliability of supply.

Visual exposure to large and small portion sizes and perceptions of portion size normality: Three experimental studies.

Science.gov (United States)

Robinson, Eric; Oldham, Melissa; Cuckson, Imogen; Brunstrom, Jeffrey M; Rogers, Peter J; Hardman, Charlotte A

2016-03-01

Portion sizes of many foods have increased in recent times. In three studies we examined the effect that repeated visual exposure to larger versus smaller food portion sizes has on perceptions of what constitutes a normal-sized food portion and measures of portion size selection. In studies 1 and 2 participants were visually exposed to images of large or small portions of spaghetti bolognese, before making evaluations about an image of an intermediate sized portion of the same food. In study 3 participants were exposed to images of large or small portions of a snack food before selecting a portion size of snack food to consume. Across the three studies, visual exposure to larger as opposed to smaller portion sizes resulted in participants considering a normal portion of food to be larger than a reference intermediate sized portion. In studies 1 and 2 visual exposure to larger portion sizes also increased the size of self-reported ideal meal size. In study 3 visual exposure to larger portion sizes of a snack food did not affect how much of that food participants subsequently served themselves and ate. Visual exposure to larger portion sizes may adjust visual perceptions of what constitutes a 'normal' sized portion. However, we did not find evidence that visual exposure to larger portions altered snack food intake. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

77 FR 53769 - Receipts-Based, Small Business Size Standard; Confirmation of Effective Date

Science.gov (United States)

2012-09-04

... Flexibility Act of 1980, as amended. The NRC is increasing its receipts-based, small business size standard from $6.5 million to $7 million to conform to the standard set by the Small Business Administration...-Based, Small Business Size Standard; Confirmation of Effective Date AGENCY: Nuclear Regulatory...

78 FR 30384 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Science.gov (United States)

2013-05-22

... SBA's 8(a) Business Development (BD) program, or Women-Owned Small Businesses (WOSBs). DATES: Comments... small businesses, Service-Disabled Veteran-Owned (SDVO) small businesses, Women-Owned Small Businesses... SMALL BUSINESS ADMINISTRATION Small Business Size Standards: Waiver of the Nonmanufacturer Rule...

JAIF report on small- and medium-size LWRs

International Nuclear Information System (INIS)

Anon.

1983-01-01

The Ministry of International Trade and Industry has made a report on the results of the study on the utilization of small and medium size LWRs. The Japan Atomic Industrial Forum undertook this research work by the commission of the Ministry. It studied six cases of PWRs and BWRs with thermal output power ranging from 20 MWt to 700 MWt as the hypothetical design for their siting conditions, reactor capacity and the examples of utilization of the corresponding steam output. A large housing estate of 5,000 units, a local core city with population of 100,000, industrial utilization for petrochemical plants and paper and pulp plants and the combined utilization for a factory and a housing estate of 5,000 units were examined. The report said that a city with population of 100,000 would be the best object to supply heat from a nuclear reactor, and it is important to develop the nuclear reactors with 200 MWt capacity. This type is versatile in the siting conditions, and can be constructed near a city, accordingly, it offers the possibility of extensive utilization. The significance of small and medium size LWRs as the alternative energy for oil, the regional development accompanying the use of small and medium size LWRs, the technical development toward scale reduction, easy operation and versatile utilization, the economical evaluation of the utilization models and the tasks for the future are reported. (Kako, I.)

Inter- and intra-observer reliability of masking in plantar pressure measurement analysis.

Science.gov (United States)

Deschamps, K; Birch, I; Mc Innes, J; Desloovere, K; Matricali, G A

2009-10-01

Plantar pressure measurement is an important tool in gait analysis. Manual placement of small masks (masking) is increasingly used to calculate plantar pressure characteristics. Little is known concerning the reliability of manual masking. The aim of this study was to determine the reliability of masking on 2D plantar pressure footprints, in a population with forefoot deformity (i.e. hallux valgus). Using a random repeated-measure design, four observers identified the third metatarsal head on a peak-pressure barefoot footprint, using a small mask. Subsequently, the location of all five metatarsal heads was identified, using the same size of masks and the same protocol. The 2D positional variation of the masks and the peak pressure (PP) and pressure time integral (PTI) values of each mask were calculated. For single-masking the lowest inter-observer reliability was found for the distal-proximal direction, causing a clear, adverse impact on the reliability of the pressure characteristics (PP and PTI). In the medial-lateral direction the inter-observer reliability could be scored as high. Intra-observer reliability was better and could be scored as high or good for both directions, with a correlated improved reliability of the pressure characteristics. Reliability of multi-masking showed a similar pattern, but overall values tended to be lower. Therefore, small sized masking in order to define pressure characteristics in the forefoot should be done with care.

Successful E-Learning in Small and Medium-Sized Enterprises

Science.gov (United States)

Paulsen, Morten Flate

2009-01-01

So far, e-learning has primarily been used when there are many learners involved. The up-front investments related to e-learning are relatively high, and may be perceived as prohibitive for small and medium-sized enterprises (SMEs). Some e-learning is, however, getting less expensive, and some e-learning models are more suited for small-scale…

Small is Beautiful? Firm's Size, Prevention & Food Safety.

OpenAIRE

Rouviere, Elodie; Soubeyran, Raphael

2012-01-01

The European General Food Law of 2005 and the newly promulgated FDA Food Safety Modernization Act (FFSMA) of 2010 ask all food operators to implement preventive efforts. In this article, we explore the link between firm’s size and preventive efforts. We show two main results. First, when there is no cross-contamination, small firms will provide higher preventive efforts than large firms. When there is crosscontamination, the effort-size curve may have a "inverted-U" shape. From our results we...

Evaluation research of small and medium-sized enterprise informatization on big data

Science.gov (United States)

Yang, Na

2017-09-01

Under the background of big data, key construction of small and medium-sized enterprise informationization level was needed, but information construction cost was large, while information cost of inputs can bring benefit to small and medium-sized enterprises. This paper established small and medium-sized enterprise informatization evaluation system from hardware and software security level, information organization level, information technology application and the profit level, and information ability level. The rough set theory was used to brief indexes, and then carry out evaluation by support vector machine (SVM) model. At last, examples were used to verify the theory in order to prove the effectiveness of the method.

Small angle neutron scattering measurements of magnetic cluster sizes in magnetic recorging disks

CERN Document Server

Toney, M

2003-01-01

We describe Small Angle Neutron Scattering measurements of the magnetic cluster size distributions for several longitudinal magnetic recording media. We find that the average magnetic cluster size is slightly larger than the average physical grain size, that there is a broad distribution of cluster sizes, and that the cluster size is inversely correlated to the media signal-to-noise ratio. These results show that intergranular magnetic coupling in these media is small and they provide empirical data for the cluster-size distribution that can be incorporated into models of magnetic recording.

76 FR 42157 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Science.gov (United States)

2011-07-18

... (BD) Program, or Women-Owned Small Business (WOSB) concerns to provide the products of small business... SMALL BUSINESS ADMINISTRATION Small Business Size Standards: Waiver of the Nonmanufacturer Rule AGENCY: U.S. Small Business Administration. ACTION: Notice of Denial to Waive the Nonmanufacturer Rule...

76 FR 42157 - Small Business Size Standards; Waiver of the Nonmanufacturer Rule

Science.gov (United States)

2011-07-18

... Development (BD) Program, or Women- Owned Small Business (WOSB) concerns to provide the products of small... SMALL BUSINESS ADMINISTRATION Small Business Size Standards; Waiver of the Nonmanufacturer Rule AGENCY: U.S. Small Business Administration. ACTION: Notice of Retraction of a Class Waiver SUMMARY: The U...

Significance assessment of small-medium sized reactors

Energy Technology Data Exchange (ETDEWEB)

Kanno, Minoru [Japan Atomic Power Co., Research and Development Dept., Tokyo (Japan)

2002-12-01

Preliminary assessment for deployment of small-medium sized reactor (S and M reactor) as a future option has been conducted at the JAPCO (Japan Atomic Power Company) under the cooperation with the CRIERI (Central Research Institute of Electric Power Industry). Significance of the S and M reactor introduction is listed as follows; lower investment cost, possible siting near demand side, enlarged freedom of siting, shorter transmission line, good compatibility with slow increase of demand and plain explanation of safety using simpler system such as integral type vessel without piping, natural convection core cooling and passive safety system. The deployment of simpler plant system, modular shop fabrication, ship-shell structured building and longer operation period can assure economics comparable with that of a large sized reactor, coping with scale-demerit. Also the S and M reactor is preferable in size for the nuclear heat utilization such as hydrogen production. (T. Tanaka)

Overestimation of test performance by ROC analysis: Effect of small sample size

International Nuclear Information System (INIS)

Seeley, G.W.; Borgstrom, M.C.; Patton, D.D.; Myers, K.J.; Barrett, H.H.

1984-01-01

New imaging systems are often observer-rated by ROC techniques. For practical reasons the number of different images, or sample size (SS), is kept small. Any systematic bias due to small SS would bias system evaluation. The authors set about to determine whether the area under the ROC curve (AUC) would be systematically biased by small SS. Monte Carlo techniques were used to simulate observer performance in distinguishing signal (SN) from noise (N) on a 6-point scale; P(SN) = P(N) = .5. Four sample sizes (15, 25, 50 and 100 each of SN and N), three ROC slopes (0.8, 1.0 and 1.25), and three intercepts (0.8, 1.0 and 1.25) were considered. In each of the 36 combinations of SS, slope and intercept, 2000 runs were simulated. Results showed a systematic bias: the observed AUC exceeded the expected AUC in every one of the 36 combinations for all sample sizes, with the smallest sample sizes having the largest bias. This suggests that evaluations of imaging systems using ROC curves based on small sample size systematically overestimate system performance. The effect is consistent but subtle (maximum 10% of AUC standard deviation), and is probably masked by the s.d. in most practical settings. Although there is a statistically significant effect (F = 33.34, P<0.0001) due to sample size, none was found for either the ROC curve slope or intercept. Overestimation of test performance by small SS seems to be an inherent characteristic of the ROC technique that has not previously been described

A practical and theoretical definition of very small field size for radiotherapy output factor measurements.

Science.gov (United States)

Charles, P H; Cranmer-Sargison, G; Thwaites, D I; Crowe, S B; Kairn, T; Knight, R T; Kenny, J; Langton, C M; Trapp, J V

2014-04-01

This work introduces the concept of very small field size. Output factor (OPF) measurements at these field sizes require extremely careful experimental methodology including the measurement of dosimetric field size at the same time as each OPF measurement. Two quantifiable scientific definitions of the threshold of very small field size are presented. A practical definition was established by quantifying the effect that a 1 mm error in field size or detector position had on OPFs and setting acceptable uncertainties on OPF at 1%. Alternatively, for a theoretical definition of very small field size, the OPFs were separated into additional factors to investigate the specific effects of lateral electronic disequilibrium, photon scatter in the phantom, and source occlusion. The dominant effect was established and formed the basis of a theoretical definition of very small fields. Each factor was obtained using Monte Carlo simulations of a Varian iX linear accelerator for various square field sizes of side length from 4 to 100 mm, using a nominal photon energy of 6 MV. According to the practical definition established in this project, field sizes ≤ 15 mm were considered to be very small for 6 MV beams for maximal field size uncertainties of 1 mm. If the acceptable uncertainty in the OPF was increased from 1.0% to 2.0%, or field size uncertainties are 0.5 mm, field sizes ≤ 12 mm were considered to be very small. Lateral electronic disequilibrium in the phantom was the dominant cause of change in OPF at very small field sizes. Thus the theoretical definition of very small field size coincided to the field size at which lateral electronic disequilibrium clearly caused a greater change in OPF than any other effects. This was found to occur at field sizes ≤ 12 mm. Source occlusion also caused a large change in OPF for field sizes ≤ 8 mm. Based on the results of this study, field sizes ≤ 12 mm were considered to be theoretically very small for 6 MV beams. Extremely

A pulse-width modulated, high reliability charge controller for small photovoltaic systems

Energy Technology Data Exchange (ETDEWEB)

Gerken, K. [Morningstar Corp., Olney, MD (United States); Welsh, D. [Morningstar Corp., Encinitas, CA (United States)

1997-02-01

This report presents the results of a development effort to design, test and begin production of a new class of small photovoltaic (PV) charge controllers. Sandia National Laboratories provided technical support, test data and financial support through a Balance-of-System Development contract. One of the objectives of the development was to increase user confidence in small PV systems by improving the reliability and operating life of the system controllers. Another equally important objective was to improve the economics of small PV systems by extending the battery lifetimes. Using new technology and advanced manufacturing techniques, these objectives were accomplished. Because small stand-alone PV systems account for over one third of all PV modules shipped, the positive impact of improving the reliability and economics of PV systems in this market segment will be felt throughout the industry. The results of verification testing of the new product are also included in this report. The initial design goals and specifications were very aggressive, but the extensive testing demonstrates that all the goals were achieved. Production of the product started in May at a rate of 2,000 units per month. Over 40 Morningstar distributors (5 US and 35 overseas) have taken delivery in the first 2 months of shipments. Initial customer reactions to the new controller have been very favorable.

Visual exposure to large and small portion sizes and perceptions of portion size normality: Three experimental studies

OpenAIRE

Robinson, Eric; Oldham, Melissa; Cuckson, Imogen; Brunstrom, Jeffrey M.; Rogers, Peter J.; Hardman, Charlotte A.

2016-01-01

Portion sizes of many foods have increased in recent times. In three studies we examined the effect that repeated visual exposure to larger versus smaller food portion sizes has on perceptions of what constitutes a normal-sized food portion and measures of portion size selection. In studies 1 and 2 participants were visually exposed to images of large or small portions of spaghetti bolognese, before making evaluations about an image of an intermediate sized portion of the same food. In study ...

Reliability and cost evaluation of small isolated power systems containing photovoltaic and wind energy

Science.gov (United States)

Karki, Rajesh

Renewable energy application in electric power systems is growing rapidly worldwide due to enhanced public concerns for adverse environmental impacts and escalation in energy costs associated with the use of conventional energy sources. Photovoltaics and wind energy sources are being increasingly recognized as cost effective generation sources. A comprehensive evaluation of reliability and cost is required to analyze the actual benefits of utilizing these energy sources. The reliability aspects of utilizing renewable energy sources have largely been ignored in the past due the relatively insignificant contribution of these sources in major power systems, and consequently due to the lack of appropriate techniques. Renewable energy sources have the potential to play a significant role in the electrical energy requirements of small isolated power systems which are primarily supplied by costly diesel fuel. A relatively high renewable energy penetration can significantly reduce the system fuel costs but can also have considerable impact on the system reliability. Small isolated systems routinely plan their generating facilities using deterministic adequacy methods that cannot incorporate the highly erratic behavior of renewable energy sources. The utilization of a single probabilistic risk index has not been generally accepted in small isolated system evaluation despite its utilization in most large power utilities. Deterministic and probabilistic techniques are combined in this thesis using a system well-being approach to provide useful adequacy indices for small isolated systems that include renewable energy. This thesis presents an evaluation model for small isolated systems containing renewable energy sources by integrating simulation models that generate appropriate atmospheric data, evaluate chronological renewable power outputs and combine total available energy and load to provide useful system indices. A software tool SIPSREL+ has been developed which generates

Export Marketing Involvement of African Small and Medium Size ...

African Journals Online (AJOL)

Export Marketing Involvement of African Small and Medium Size Enterprises: Tanzania's Fish Processing Industry. ... This study examined the Export marketing involvement of SMEs from the Least ... EMAIL FULL TEXT EMAIL FULL TEXT

75 FR 68394 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Science.gov (United States)

2010-11-05

..., Participants in SBA's 8(a) Business Development (BD) Program, or Women-Owned Small Business (WOSB) concerns... SMALL BUSINESS ADMINISTRATION Small Business Size Standards: Waiver of the Nonmanufacturer Rule AGENCY: U.S. Small Business Administration. ACTION: Notice of Waiver to the Nonmanufacturer Rule for...

78 FR 61443 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Science.gov (United States)

2013-10-03

... SBA's 8(a) Business Development Program, or Women-Owned Small Businesses to provide aerospace ball and... businesses, Women-Owned Small Businesses, or Participants in the SBA's 8(a) Business Development Program... SMALL BUSINESS ADMINISTRATION Small Business Size Standards: Waiver of the Nonmanufacturer Rule...

Improvement of environmental management incentives for small and medium-sized enterprises

Energy Technology Data Exchange (ETDEWEB)

Chang, Kee Bok; Lee, Seung Kyu; Lim, Chae Woon; Chung, Ho Sun [Korea Environment Institute, Seoul (Korea)

1998-12-01

The developed countries have been prepared the national innovation for sustainable development for a long time. The international advanced enterprises, such as multinational enterprises, are enhancing the active and strategic environmental management. However, in spite of such changes in the world, small and middle-sized enterprises do not show any substantial changes. It is true that most of enterprises do not recognize the need of environmental management. Although they have intention for environmental improvement, it is also true that they do not have any strength to maintain effective management. Moreover, with over 99% of small and middle-sized enterprises among entire enterprises in Korea, it is hardly possible to establish an effective regulation system. The purpose of this study is to make a policy plan to induce the development of environmental friendly small and middle-sized enterprises under the recognition of such problems. 138 refs., 4 figs., 195 tabs.

Role of Relationship Marketing in Small and Medium-Sized Entreprises

OpenAIRE

Ružica Butigan; Ivana Mahnić

2011-01-01

Along with marketing, small and medium enterprises (SMEs) are commonly associated in literature with relationship marketing which results in marketing networks. This paper examines the specific characteristics that differentiate large companies from small and medium-sized enterprises, and the reasons that prevent SMEs from engaging in traditional marketing within the scope of marketing mix. The paper also shows that the key characteristic which distinguishes small from large companies is a pr...

A stochastic simulation model for reliable PV system sizing providing for solar radiation fluctuations

International Nuclear Information System (INIS)

Kaplani, E.; Kaplanis, S.

2012-01-01

Highlights: ► Solar radiation data for European cities follow the Extreme Value or Weibull distribution. ► Simulation model for the sizing of SAPV systems based on energy balance and stochastic analysis. ► Simulation of PV Generator-Loads-Battery Storage System performance for all months. ► Minimum peak power and battery capacity required for reliable SAPV sizing for various European cities. ► Peak power and battery capacity reduced by more than 30% for operation 95% success rate. -- Abstract: The large fluctuations observed in the daily solar radiation profiles affect highly the reliability of the PV system sizing. Increasing the reliability of the PV system requires higher installed peak power (P m ) and larger battery storage capacity (C L ). This leads to increased costs, and makes PV technology less competitive. This research paper presents a new stochastic simulation model for stand-alone PV systems, developed to determine the minimum installed P m and C L for the PV system to be energy independent. The stochastic simulation model developed, makes use of knowledge acquired from an in-depth statistical analysis of the solar radiation data for the site, and simulates the energy delivered, the excess energy burnt, the load profiles and the state of charge of the battery system for the month the sizing is applied, and the PV system performance for the entire year. The simulation model provides the user with values for the autonomy factor d, simulating PV performance in order to determine the minimum P m and C L depending on the requirements of the application, i.e. operation with critical or non-critical loads. The model makes use of NASA’s Surface meteorology and Solar Energy database for the years 1990–2004 for various cities in Europe with a different climate. The results obtained with this new methodology indicate a substantial reduction in installed peak power and battery capacity, both for critical and non-critical operation, when compared to

Reliable and Accurate Release of Micro-Sized Objects with a Gripper that Uses the Capillary-Force Method

Directory of Open Access Journals (Sweden)

Suzana Uran

2017-06-01

Full Text Available There have been recent developments in grippers that are based on capillary force and condensed water droplets. These are used for manipulating micro-sized objects. Recently, one-finger grippers have been produced that are able to reliably grip using the capillary force. To release objects, either the van der Waals, gravitational or inertial-forces method is used. This article presents methods for reliably gripping and releasing micro-objects using the capillary force. The moisture from the surrounding air is condensed into a thin layer of water on the contact surfaces of the objects. From the thin layer of water, a water meniscus between the micro-sized object, the gripper and the releasing surface is created. Consequently, the water meniscus between the object and the releasing surface produces a high enough capillary force to release the micro-sized object from the tip of the one-finger gripper. In this case, either polystyrene, glass beads with diameters between 5–60 µm, or irregularly shaped dust particles of similar sizes were used. 3D structures made up of micro-sized objects could be constructed using this method. This method is reliable for releasing during assembly and also for gripping, when the objects are removed from the top of the 3D structure—the so-called “disassembling gripping” process. The accuracy of the release was lower than 0.5 µm.

Estimating sample size for a small-quadrat method of botanical ...

African Journals Online (AJOL)

Reports the results of a study conducted to determine an appropriate sample size for a small-quadrat method of botanical survey for application in the Mixed Bushveld of South Africa. Species density and grass density were measured using a small-quadrat method in eight plant communities in the Nylsvley Nature Reserve.

78 FR 76886 - Small Business Size Standards: Waiver of the Nonmanufacturer Rule

Science.gov (United States)

2013-12-19

..., Participants in SBA's 8(a) Business Development (BD) Program, or Women-Owned Small Business (WOSB) concerns... SMALL BUSINESS ADMINISTRATION Small Business Size Standards: Waiver of the Nonmanufacturer Rule AGENCY: U.S. Small Business Administration. ACTION: Notice of Final Action: Granting Class Waiver of the...

Big Data, Small Sample.

Science.gov (United States)

Gerlovina, Inna; van der Laan, Mark J; Hubbard, Alan

2017-05-20

Multiple comparisons and small sample size, common characteristics of many types of "Big Data" including those that are produced by genomic studies, present specific challenges that affect reliability of inference. Use of multiple testing procedures necessitates calculation of very small tail probabilities of a test statistic distribution. Results based on large deviation theory provide a formal condition that is necessary to guarantee error rate control given practical sample sizes, linking the number of tests and the sample size; this condition, however, is rarely satisfied. Using methods that are based on Edgeworth expansions (relying especially on the work of Peter Hall), we explore the impact of departures of sampling distributions from typical assumptions on actual error rates. Our investigation illustrates how far the actual error rates can be from the declared nominal levels, suggesting potentially wide-spread problems with error rate control, specifically excessive false positives. This is an important factor that contributes to "reproducibility crisis". We also review some other commonly used methods (such as permutation and methods based on finite sampling inequalities) in their application to multiple testing/small sample data. We point out that Edgeworth expansions, providing higher order approximations to the sampling distribution, offer a promising direction for data analysis that could improve reliability of studies relying on large numbers of comparisons with modest sample sizes.

Effects of Group Size on Students Mathematics Achievement in Small Group Settings

Science.gov (United States)

Enu, Justice; Danso, Paul Amoah; Awortwe, Peter K.

2015-01-01

An ideal group size is hard to obtain in small group settings; hence there are groups with more members than others. The purpose of the study was to find out whether group size has any effects on students' mathematics achievement in small group settings. Two third year classes of the 2011/2012 academic year were selected from two schools in the…

Human resources management within the process management in small and medium-sized enterprises

Directory of Open Access Journals (Sweden)

Marie Duspivová

2013-01-01

Full Text Available Sector of small and medium-sized enterprises is regarded as the backbone of the economy and a driving force of innovation, employment and social integration. Development of the sector of small and medium-sized enterprises in the Czech Republic has a substantial impact on economic and social development of the country and its various regions. This article deals with the human resources management in small and medium-sized enterprises, because it is more than obvious recently that the prosperity of the organization is depended on human resources and management of them can determine not only whether the organizations succeed, but whether it will be able to survive in turbulent conditions in the present world. The main aim of this paper is to analytical describe the monitoring the process of human resources management in selected categories of enterprises by business activity and number of employees including statistical analysis of causal effects. Further to analytical describe the evaluation the process of human resources management and indicators of this process, which are monitored by small and medium-sized enterprises. To achieve this aim were used selected primary data collected in the project GAJU 068/2010/S titled “Process management and its possible implementation in small and medium-sized enterprises”.

Potential growth and opportunities for Kenyan small sized firms online : E-business adoption for small boutiques and the new customer online

OpenAIRE

Mbare, Candy

2016-01-01

The purpose of this thesis is to identify the online growth opportunities for the small sized firm in Kenya. Kenya is the most developed nation in East-Africa. E-commerce is a rapidly rising trend in developing nations, that provides small sized firms with growth opportunities. The e-commerce trend also comes with changes in consumer behavior. Sufficient use of e-commerce by small sized firms in Kenya, can open a opportunity to reach a wider range of audience and increase profits by expan...

Small-size pedestrian detection in large scene based on fast R-CNN

Science.gov (United States)

Wang, Shengke; Yang, Na; Duan, Lianghua; Liu, Lu; Dong, Junyu

2018-04-01

Pedestrian detection is a canonical sub-problem of object detection with high demand during recent years. Although recent deep learning object detectors such as Fast/Faster R-CNN have shown excellent performance for general object detection, they have limited success for small size pedestrian detection in large-view scene. We study that the insufficient resolution of feature maps lead to the unsatisfactory accuracy when handling small instances. In this paper, we investigate issues involving Fast R-CNN for pedestrian detection. Driven by the observations, we propose a very simple but effective baseline for pedestrian detection based on Fast R-CNN, employing the DPM detector to generate proposals for accuracy, and training a fast R-CNN style network to jointly optimize small size pedestrian detection with skip connection concatenating feature from different layers to solving coarseness of feature maps. And the accuracy is improved in our research for small size pedestrian detection in the real large scene.

Design concepts and safety concerns of the small and medium size reactors (SMR)

International Nuclear Information System (INIS)

Seul, Kwang Won; Lee, Jae Hun; Kim, Hho Jung

1998-01-01

The small and medium size reactors (SMR) and interface facilities such as desalination plant are expected to be located near the population area because of restrictions in transporting the plant products such as fresh water to long distance area. To protect the public around the plant facility from the possible release of radioactive materials, the design development of the SMR is focusing on an enhancement of the safety and reliability as well as the economics. In this study, the major safety concepts of the SMR designs significantly different from the current PWR designs are investigated and the safety concerns applicable to the integrated SMR design of Korea (called SMART), were identified. Those safety issues include the use of proven technology, application of strengthening defense in depth, event categorization and selection, simplification of emergency planning, determination of accident source terms and so on. The efforts to resolve the safety concerns in the design stage will provide an improvement of the safety of the SMART design

Unions in small and medium-sized enterprises

DEFF Research Database (Denmark)

Holten, Ann-Louise; Crouch, Colin

2014-01-01

Trade unions are commonly weak in small- and medium-sized enterprises, which constitute a majority of European firms and are often family-owned. We investigate the influence of family ownership on employee membership, perceptions and experience with unions in Danish and Italian firms in the textile...... and clothing sector. Family ownership reduces union membership; and within family firms, the number of family members employed is negatively associated with unionization rates and employee perceptions of unions....

Size matters: bigger is faster.

Science.gov (United States)

Sereno, Sara C; O'Donnell, Patrick J; Sereno, Margaret E

2009-06-01

A largely unexplored aspect of lexical access in visual word recognition is "semantic size"--namely, the real-world size of an object to which a word refers. A total of 42 participants performed a lexical decision task on concrete nouns denoting either big or small objects (e.g., bookcase or teaspoon). Items were matched pairwise on relevant lexical dimensions. Participants' reaction times were reliably faster to semantically "big" versus "small" words. The results are discussed in terms of possible mechanisms, including more active representations for "big" words, due to the ecological importance attributed to large objects in the environment and the relative speed of neural responses to large objects.

Mechanism of Interaction between Entrepreneurial Spirit and Growth of Small and Medium Sized Private Enterprises

Institute of Scientific and Technical Information of China (English)

Peng XIE

2016-01-01

In the context of government appeal of " mass entrepreneurship and innovation",all areas launched the movement of " mass entrepreneurship" and " grassroots entrepreneurship". As parts of vitality of China’s market economy,small and medium sized private enterprises become grassroots of market competition in talents,funds,and technologies. This paper combined three levels of entrepreneurial spirit and small and medium sized private enterprises,studied acting mechanism of entrepreneurial spirit,discussed competitive power of small and medium sized private enterprises,and recommended that small and medium sized private enterprises should cultivate core competitive power,adapt to external environment,and create external environment support,to realize sound development.

The status of development of small and medium sized reactors

International Nuclear Information System (INIS)

Konstantinov, L.V; Kupitz, J.

1987-01-01

Several IAEA Member States have shown their interest in reactor design, having a smaller power rating (100-500 MW(e) range) than those generally available on the international market. These small and medium sized power reactors are of interest either for domestic applications or for export into countries with less developed infrastructure. There are different developments undertaken for these power reactors to be ready for offering in the nineties and beyond. The paper gives an overview about the status and different trends in IAEA Member States in the development of small and medium sized reactors for the 90's and provides an outlook for very new reactor designs as a long term option for nuclear power. (author)

Reliable Stair Climbing in the Simple Hexapod 'RHex'

National Research Council Canada - National Science Library

Moore, E. Z; Campbell, D; Grimminger, F; Buehler, M

2002-01-01

.... In this paper, we describe an open loop controller that enables our small robot (Length: 51 cm, Width: 20 cm, Height: 12.7 cm. Leg length: 16 cm), to reliably climb a wide range of regular, full-size stairs with no operator input during stair climbing...

77 FR 7489 - Small Business Size Standards: Professional, Technical, and Scientific Services

Science.gov (United States)

2012-02-10

... would (1) provide a competitive advantage to larger firms over their truly small counterparts; (2) allow... Vol. 77 Friday, No. 28 February 10, 2012 Part V Small Business Administration 13 CFR Part 121 Small Business Size Standards: Professional, Technical, and Scientific Services; Final Rule #0;#0...

A critical evaluation of deterministic methods in size optimisation of reliable and cost effective standalone hybrid renewable energy systems

International Nuclear Information System (INIS)

Maheri, Alireza

2014-01-01

Reliability of a hybrid renewable energy system (HRES) strongly depends on various uncertainties affecting the amount of power produced by the system. In the design of systems subject to uncertainties, both deterministic and nondeterministic design approaches can be adopted. In a deterministic design approach, the designer considers the presence of uncertainties and incorporates them indirectly into the design by applying safety factors. It is assumed that, by employing suitable safety factors and considering worst-case-scenarios, reliable systems can be designed. In fact, the multi-objective optimisation problem with two objectives of reliability and cost is reduced to a single-objective optimisation problem with the objective of cost only. In this paper the competence of deterministic design methods in size optimisation of reliable standalone wind–PV–battery, wind–PV–diesel and wind–PV–battery–diesel configurations is examined. For each configuration, first, using different values of safety factors, the optimal size of the system components which minimises the system cost is found deterministically. Then, for each case, using a Monte Carlo simulation, the effect of safety factors on the reliability and the cost are investigated. In performing reliability analysis, several reliability measures, namely, unmet load, blackout durations (total, maximum and average) and mean time between failures are considered. It is shown that the traditional methods of considering the effect of uncertainties in deterministic designs such as design for an autonomy period and employing safety factors have either little or unpredictable impact on the actual reliability of the designed wind–PV–battery configuration. In the case of wind–PV–diesel and wind–PV–battery–diesel configurations it is shown that, while using a high-enough margin of safety in sizing diesel generator leads to reliable systems, the optimum value for this margin of safety leading to a

The reliability of ultrasonic inspection and the critical defect size

International Nuclear Information System (INIS)

Vasilchenko, G.S.; Bely, V.E.; Ovchinnikov, A.V.; Rivkin, E.Yu.

1991-01-01

The ability to detect fabrication and service-induced defects in the welded joints of components and pipelines in nuclear power stations by ultrasonic inspection when this is conducted by using standard instruments and procedures appears to be insufficient. This fact was confirmed by the research carried out in PISC program and other studies. In order to increase the accuracy of measurement and to obtain the additional information on the character of any defect in ultrasonic testing as well as the validity of applying nondestructive testing data to strength calculation, scientific researches have been promoted and carried out in the USSR in a program under the guidance of NPO CNIITMASH. The reliability of the ultrasonic control of welded joints and the ways and means for its improvement are discussed. The presentation of the parameters realized by the ultrasonic inspection of defects in the form of schema for the use in strength calculation is explained. The calculation of stress intensity factor, the estimation of critical defect size, and the estimation of acceptable defect size are reported. (K.I.)

Project appraisal for small and medium size wind energy installation: The Italian wind energy policy effects

International Nuclear Information System (INIS)

Fera, M.; Iannone, R.; Macchiaroli, R.; Miranda, S.; Schiraldi, M.M.

2014-01-01

In the last few years, the distributed energy production from small wind turbines (i.e.<200 kWp) has developed into a relevant business opportunity for different investors in Italy. The market, especially in Italy, has rapidly grown, achieving 9 MWp only in 2011, with an increase from 1.5 MW in 2009 to 13.3 MW at the end of 2011. This paper reports the results of a case study on the installation of several small wind turbines. It aims to provide an analysis of the conditions in Italy that make it possible to install these machines and offer a reliable reference for designing, planning, and controlling small wind turbine projects while focusing on the strategic variables of time, cost, and quality used by typical enterprises in the investment projects. The results are relevant to investors as well as engineering, procurement, and construction companies involved in this new sector, which must understand Italy’s renewable energy policy and its effects in practice. Moreover, certain national energy policy conclusions are reported and discussed in this paper. To properly study the sector, the data on time, cost and quality are analysed using typical project management tools. - Highlights: • Focus on the Italian wind energy sector. • Analysis of Italian policy effects. • Focus on small/medium size wind energy machines

Large- and small-size advantages in sneaking behaviour in the dusky frillgoby Bathygobius fuscus

Science.gov (United States)

Takegaki, Takeshi; Kaneko, Takashi; Matsumoto, Yukio

2012-04-01

Sneaking tactic, a male alternative reproductive tactic involving sperm competition, is generally adopted by small individuals because of its inconspicuousness. However, large size has an advantage when competition occurs between sneakers for fertilization of eggs. Here, we suggest that both large- and small-size advantages of sneaker males are present within the same species. Large sneaker males of the dusky frillgoby Bathygobius fuscus showed a high success rate in intruding into spawning nests because of their advantage in competition among sneaker males in keeping a suitable position to sneak, whereas small sneakers had few chances to sneak. However, small sneaker males were able to stay in the nests longer than large sneaker males when they succeeded in sneak intrusion. This suggests the possibility of an increase in their paternity. The findings of these size-specific behavioural advantages may be important in considering the evolution of size-related reproductive traits.

Sustainability and Small to Medium Sized Enterprises--How to Engage Them

Science.gov (United States)

Condon, Linda

2004-01-01

Small and medium sized enterprises (SMEs) have a major advantage over larger organisations in regard to addressing sustainability issues--their size means they are able to react very quickly to changes in the business environment. They are disadvantaged, however, by lack of information on marketplace changes that make sustainability an opportunity…

Small nuclear power reactor emergency electric power supply system reliability comparative analysis; Analise da confiabilidade do sistema de suprimento de energia eletrica de emergencia de um reator nuclear de pequeno porte

Energy Technology Data Exchange (ETDEWEB)

Bonfietti, Gerson

2003-07-01

This work presents an analysis of the reliability of the emergency power supply system, of a small size nuclear power reactor. Three different configurations are investigated and their reliability analyzed. The fault tree method is used as the main tool of analysis. The work includes a bibliographic review of emergency diesel generator reliability and a discussion of the design requirements applicable to emergency electrical systems. The influence of common cause failure influences is considered using the beta factor model. The operator action is considered using human failure probabilities. A parametric analysis shows the strong dependence between the reactor safety and the loss of offsite electric power supply. It is also shown that common cause failures can be a major contributor to the system reliability. (author)

International orientation and export commitment in fast small and medium size firms internationalization: scales validation and implications for the Brazilian case

Directory of Open Access Journals (Sweden)

Marcelo André Machado

Full Text Available Abstract A set of changes in the competitive environment has recently provoked the emergence of a new kind of organization that has since its creation a meaningful share of its revenue being originated from international activities developed in more than one continent. Within this new reality, the internationalization of the firm in phases or according to its growth has resulted in it losing its capacity to explain this process with regard to small- and medium-sized enterprises (SME. Thus, in this paper, the international orientation (IO and export commitment (EC constructs have been revised under a theoretical context of the fast internationalization of medium-sized companies, so as to identify scales that more accurately measure these dimensions in the Brazilian setting. After a literature review and an exploratory research, the IO and EC scales proposed by Knight and Cavusgil (2004 and Shamsuddoha and Ali (2006 were respectively applied to a sample of 398 small- and medium-sized exporting Brazilian companies. In spite of conjunction and situation differences inherent to the Brazilian companies, the selected scales presented high measuring reliability. Furthermore, the field research outcomes provide evidence for the existence of a phenomenon of fast internationalization in medium-sized companies in Brazil, as well as support some theoretical assumptions of other empirical investigations carried out with samples from developed countries.

77 FR 58747 - Small Business Size Standards: Real Estate and Rental and Leasing

Science.gov (United States)

2012-09-24

...: The United States Small Business Administration (SBA) is increasing the small business size standards... small businesses, the commenter suggested increasing it to $150 million. He contended that his business... industry makes it difficult for small businesses to grow and develop and increase their market share. To...

Observations of Bright Massive Stars Using Small Size Telescopes

Science.gov (United States)

Beradze, Sopia; Kochiashvili, Nino

2017-11-01

The size of a telescope determines goals and objects of observations. During the latest decades it becomes more and more difficult to get photometric data of bright stars because most of telescopes of small sizes do not operate already. But there are rather interesting questions connected to the properties and evolution ties between different types of massive stars. Multi-wavelength photometric data are needed for solution of some of them. We are presenting our observational plans of bright Massive X-ray binaries, WR and LBV stars using a small size telescope. All these stars, which are presented in the poster are observational targets of Sopia Beradze's future PhD thesis. We already have got very interesting results on the reddening and possible future eruption of the massive hypergiant star P Cygni. Therefore, we decided to choose some additional interesting massive stars of different type for future observations. All Massive stars play an important role in the chemical evolution of galaxies because of they have very high mass loss - up to 10-4M⊙/a year. Our targets are on different evolutionary stages and three of them are the members of massive binaries. We plan to do UBVRI photometric observations of these stars using the 48 cm Cassegrain telescope of the Abastumani Astrophisical Observatory.

Small-for-Size Liver Transplantation Increases Pulmonary Injury in Rats: Prevention by NIM811

Directory of Open Access Journals (Sweden)

Qinlong Liu

2012-01-01

Full Text Available Pulmonary complications after liver transplantation (LT often cause mortality. This study investigated whether small-for-size LT increases acute pulmonary injury and whether NIM811 which improves small-for-size liver graft survival attenuates LT-associated lung injury. Rat livers were reduced to 50% of original size, stored in UW-solution with and without NIM811 (5 μM for 6 h, and implanted into recipients of the same or about twice the donor weight, resulting in half-size (HSG and quarter-size grafts (QSG, respectively. Liver injury increased and regeneration was suppressed after QSG transplantation as expected. NIM811 blunted these alterations >75%. Pulmonary histological alterations were minimal at 5–18 h after LT. At 38 h, neutrophils and monocytes/macrophage infiltration, alveolar space exudation, alveolar septal thickening, oxidative/nitrosative protein adduct formation, and alveolar epithelial cell/capillary endothelial apoptosis became overt in the lungs of QSG recipients, but these alterations were mild in full-size and HSG recipients. Liver pretreatment with NIM811 markedly decreased pulmonary injury in QSG recipients. Hepatic TNFα and IL-1β mRNAs and pulmonary ICAM-1 expression were markedly higher after QSG transplantation, which were all decreased by NIM811. Together, dysfunctional small-for-size grafts produce toxic cytokines, leading to lung inflammation and injury. NIM811 decreased toxic cytokine formation, thus attenuating pulmonary injury after small-for-size LT.

Overcoming time scale and finite size limitations to compute nucleation rates from small scale well tempered metadynamics simulations

Science.gov (United States)

Salvalaglio, Matteo; Tiwary, Pratyush; Maggioni, Giovanni Maria; Mazzotti, Marco; Parrinello, Michele

2016-12-01

Condensation of a liquid droplet from a supersaturated vapour phase is initiated by a prototypical nucleation event. As such it is challenging to compute its rate from atomistic molecular dynamics simulations. In fact at realistic supersaturation conditions condensation occurs on time scales that far exceed what can be reached with conventional molecular dynamics methods. Another known problem in this context is the distortion of the free energy profile associated to nucleation due to the small, finite size of typical simulation boxes. In this work the problem of time scale is addressed with a recently developed enhanced sampling method while contextually correcting for finite size effects. We demonstrate our approach by studying the condensation of argon, and showing that characteristic nucleation times of the order of magnitude of hours can be reliably calculated. Nucleation rates spanning a range of 10 orders of magnitude are computed at moderate supersaturation levels, thus bridging the gap between what standard molecular dynamics simulations can do and real physical systems.

Small and medium sized reactors: Status and prospects. Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-08-01

During the early years of nuclear power deployment, the plants entering service were dominated by what are now considered small (less than 300 MW(e)) and medium (300 to 700 MW(e)) reactors. In the late 1970s, the balance shifted to larger size plants to serve the requirements of industrialized countries. However, since the early 1990s, the increased interest of developing countries in nuclear power, mainly in Asia, has resulted in intensified efforts in development of small and medium sized reactors (SMRs). Also, in industrialized countries, electricity market deregulation is calling for power generation flexibility that SMRs may offer. Apart from electricity generation, SMRs are of particular interest for non-electrical applications of nuclear energy, such as desalination of seawater and district heating. In recognition of the current global interest in small and medium sized reactors this seminar was convened to provide a forum for the exchange of information by experts and policy makers from industrialized and developing countries on the technical, economic, environmental, and social aspects of SMR development and implementation in the 21st century, and to make this information available to all interested IAEA Member States. Keynote addresses also provided information on global energy demand and supply and international trends impacting the development and introduction of SMRs. Two hundred forty seven attendees from 39 countries and 5 international organizations participated in the seminar. The majority of the participants were from developing countries. The seminar not only provided valuable up to date information on SMRs, it also highlighted the importance of continued international co-operation in the development and application of nuclear power for peaceful uses throughout the world.

Small and medium sized reactors: Status and prospects. Proceedings

International Nuclear Information System (INIS)

2002-01-01

During the early years of nuclear power deployment, the plants entering service were dominated by what are now considered small (less than 300 MW(e)) and medium (300 to 700 MW(e)) reactors. In the late 1970s, the balance shifted to larger size plants to serve the requirements of industrialized countries. However, since the early 1990s, the increased interest of developing countries in nuclear power, mainly in Asia, has resulted in intensified efforts in development of small and medium sized reactors (SMRs). Also, in industrialized countries, electricity market deregulation is calling for power generation flexibility that SMRs may offer. Apart from electricity generation, SMRs are of particular interest for non-electrical applications of nuclear energy, such as desalination of seawater and district heating. In recognition of the current global interest in small and medium sized reactors this seminar was convened to provide a forum for the exchange of information by experts and policy makers from industrialized and developing countries on the technical, economic, environmental, and social aspects of SMR development and implementation in the 21st century, and to make this information available to all interested IAEA Member States. Keynote addresses also provided information on global energy demand and supply and international trends impacting the development and introduction of SMRs. Two hundred forty seven attendees from 39 countries and 5 international organizations participated in the seminar. The majority of the participants were from developing countries. The seminar not only provided valuable up to date information on SMRs, it also highlighted the importance of continued international co-operation in the development and application of nuclear power for peaceful uses throughout the world

Supply Chain adoption in Small and Medium-Sized Enterprises (SMEs)

DEFF Research Database (Denmark)

Juhl, Mathias Thim; Bernon, Mike

Purpose: The importance of having a competitive supply chain strategy is not to be underestimated (Underwood & Agg 2012; Aronow et al. 2014). Despite the importance of creating strong supply chain capabilities, small and medium-sized enterprises (SMEs) find it difficult to implement supply chain...... and customer needs. Research Approach: An exploratory case study of five small and medium sized manufacturing companies was undertaken using in-depth interviews and business reports. Combined with relevant literature, the case study interviews provide basis for a discussion on the current adoption of supply...... needs and a low interaction in the supply chain, to having an “outside-in” perspective (Day & Moorman 2013) and development of capabilities that support long-term competitive advantage. The case studies revealed two significant factors to support consistency between supply chain capabilities...

Small-Sized Whole-Tree Harvesting in Finland

Energy Technology Data Exchange (ETDEWEB)

Kaerhae, Kalle [Metsaeteho Oy, Helsinki (Finland)

2006-07-15

In Finland, there are two mechanized harvesting systems used for small diameter (d{sub 1.3}= 10 cm) thinning wood: 1) the traditional two-machine (harvester and forwarder) system, and 2) the harwarder system (i.e. the same machine performs both felling and haulage to the roadside). At present, there are more than 20 energy wood harwarders in use in Finland. However, there have been no comprehensive studies carried out on the energy wood harwarders. This paper looks into the productivity results obtained with energy wood harwarders. In addition, the energy wood harvesting costs for harwarders are compared with those of the two-machine system. The results clearly indicated what kind of machine resources can be profitably allocated to different whole-tree harvesting sites. The energy wood harwarders should be directed towards harvesting sites where the forwarding distances are small, the trees harvested are relatively small, and the total volume of energy wood removed is quite low. Respectively, when the stem size removed is relatively large in young stands, and the forest haulage distances are long, the traditional two-machine system is more competitive.

SMALL AND MIDDLE-SIZED BUSINESS: LOGISTICAL AND SOCIAL AND ECONOMICAL FUNCTIONS

Directory of Open Access Journals (Sweden)

O. N. Pavlova

2007-01-01

Full Text Available Entrepreneurship is one of the factors that can ensure a sustainable character to the development of Belarus. The present Belarusian entrepreneurship should select the required forms and determine development priorities. It is practically impossible to do it without taking into account modem global social and economical tendencies and also specificity of Belarusian mentality and traditions. In this sense priority status is given to small and middle-sized business because it is considered as an element of economic system that ensures stability to economy. Small and middle-sized business is an ideal logistical model that provides harmonization of interests and optimization of management solutions.

Designing and Validating a Model for Measuring Sustainability of Overall Innovation Capability of Small and Medium-Sized Enterprises

Directory of Open Access Journals (Sweden)

Mohd Nizam Ab Rahman

2015-01-01

Full Text Available The business environment is currently characterized by intensified competition at both the national and firm levels. Many studies have shown that innovation positively affect firms in enhancing their competitiveness. Innovation is a dynamic process that requires a continuous, evolving, and mastered management. Evaluating the sustainability of overall innovation capability of a business is a major means of determining how well this firm effectively and efficiently manages its innovation process. A psychometrically valid scale of evaluating the sustainability of overall innovation capability of a firm is still insufficient in the current innovation literature. Thus, this study developed a reliable and valid scale of measuring the sustainability of overall innovation capability construct. The unidimensionality, reliability, and several validity components of the developed scale were tested using the data collected from 175 small and medium-sized enterprises in Iran. A series of systematic statistical analyses were performed. Results of the reliability measures, exploratory and confirmatory factor analyses, and several components of validity tests strongly supported an eight-dimensional (8D scale of measuring the sustainability of overall innovation capability construct. The dimensions of the scale were strategic management, supportive culture and structure, resource allocation, communication and networking, knowledge and technology management, idea management, project development, and commercialization capabilities.

Usefulness of Oncoplastic Volume Replacement Techniques after Breast Conserving Surgery in Small to Moderate-sized Breasts

Directory of Open Access Journals (Sweden)

Jung Dug Yang

2012-09-01

Full Text Available BackgroundIn Korean women, many of whom have small to moderate-sized breasts, it is difficult to cover a partial breast defect using oncoplastic volume displacement techniques after removal of an adequate volume of tissue during oncologic surgery. In such cases, oncoplastic volume replacement techniques are more useful.MethodsFrom January 2007 to December 2011, 104 women underwent a total of 107 breast-conserving surgeries with various kinds of oncoplastic volume replacement techniques. We used latissimus dorsi (LD myocutaneous flap for cases in which the resection mass was greater than 150 g. In case with a resection mass less than 150 g, we used regional flaps such as a lateral thoracodorsal flap, a thoracoepigastric flap, or perforator flaps such as an intercostal artery perforator (ICAP flap or a thoracodorsal artery perforator (TDAP flap.ResultsThe mean age was 46.1 years, and the average follow-up interval was 10.3 months. The patients underwent oncoplastic volume replacement techniques with a lateral thoracodorsal flap (n=9, thoracoepigastric flap (n=7, ICAP flap (n=25, TDAP flap (n=12, and LD flap (n=54. There was one case of congestion in an LD flap, and two cases of fat necrosis in an ICAP flap. Most of the patients were satisfied with the cosmetic results.ConclusionsOncoplastic volume replacement techniques can be reliable and useful for the correction of breast deformity after breast-conserving surgery, especially in patients with small to moderate-sized breasts.

A Single IGF1 Allele Is a Major Determinant of Small Size in Dogs

Science.gov (United States)

Sutter, Nathan B.; Bustamante, Carlos D.; Chase, Kevin; Gray, Melissa M.; Zhao, Keyan; Zhu, Lan; Padhukasahasram, Badri; Karlins, Eric; Davis, Sean; Jones, Paul G.; Quignon, Pascale; Johnson, Gary S.; Parker, Heidi G.; Fretwell, Neale; Mosher, Dana S.; Lawler, Dennis F.; Satyaraj, Ebenezer; Nordborg, Magnus; Lark, K. Gordon; Wayne, Robert K.; Ostrander, Elaine A.

2009-01-01

The domestic dog exhibits greater diversity in body size than any other terrestrial vertebrate. We used a strategy that exploits the breed structure of dogs to investigate the genetic basis of size. First, through a genome-wide scan, we identified a major quantitative trait locus (QTL) on chromosome 15 influencing size variation within a single breed. Second, we examined genetic variation in the 15-megabase interval surrounding the QTL in small and giant breeds and found marked evidence for a selective sweep spanning a single gene (IGF1), encoding insulin-like growth factor 1. A single IGF1 single-nucleotide polymorphism haplotype is common to all small breeds and nearly absent from giant breeds, suggesting that the same causal sequence variant is a major contributor to body size in all small dogs. PMID:17412960

Test methodology and technology of fracture toughness for small size specimens

Energy Technology Data Exchange (ETDEWEB)

Wakai, E.; Takada, F.; Ishii, T.; Ando, M. [Japan Atomic Energy Agency, Naga-gun, Ibaraki-ken (Japan); Matsukawa, S. [JNE Techno-Research Co., Kanagawa-ken (Japan)

2007-07-01

Full text of publication follows: Small specimen test technology (SSTT) is required to investigate mechanical properties in the limited availability of effective irradiation volumes in test reactors and accelerator-based neutron and charged particle sources. The test methodology guideline and the manufacture processes for very small size specimens have not been established, and we would have to formulate it. The technology to control exactly the load and displacement is also required in the test technology under the environment of high dose radiation produced from the specimens. The objective of this study is to examine the test technology and methodology of fracture toughness for very small size specimens. A new bend test machine installed in hot cell has been manufactured to obtain fracture toughness and DBTT (ductile - brittle transition temperature) of reduced-activation ferritic/martensitic steels for small bend specimens of t/2-1/3PCCVN (pre-cracked 1/3 size Charpy V-notch) with 20 mm length and DFMB (deformation and fracture mini bend specimen) with 9 mm length. The new machine can be performed at temperatures from -196 deg. C to 400 deg. C under unloading compliance method. Neutron irradiation was also performed at about 250 deg. C to about 2 dpa in JMTR. After the irradiation, fracture toughness and DBTT were examined by using the machine. Checking of displacement measurement between linear gauge of cross head's displacement and DVRT of the specimen displacement was performed exactly. Conditions of pre-crack due to fatigue in the specimen preparation were also examined and it depended on the shape and size of the specimens. Fracture toughness and DBTT of F82H steel for t/2-1/3PCCVN, DFMB and 0.18DCT specimens before irradiation were examined as a function of temperature. DBTT of smaller size specimens of DFMB was lower than that of larger size specimen of t/2-1/3PCCVN and 0.18DCT. The changes of fracture toughness and DBTT due to irradiation were also

Single Nucleotide Polymorphisms in the HIRA Gene Affect Litter Size in Small Tail Han Sheep

Directory of Open Access Journals (Sweden)

Mei Zhou

2018-05-01

Full Text Available Maintenance of appropriate levels of fecundity is critical for efficient sheep production. Opportunities to increase sheep litter size include identifying single gene mutations with major effects on ovulation rate and litter size. Whole-genome sequencing (WGS data of 89 Chinese domestic sheep from nine different geographical locations and ten Australian sheep were analyzed to detect new polymorphisms affecting litter size. Comparative genomic analysis of sheep with contrasting litter size detected a novel set of candidate genes. Two SNPs, g.71874104G>A and g.71833755T>C, were genotyped in 760 Small Tail Han sheep and analyzed for association with litter size. The two SNPs were significantly associated with litter size, being in strong linkage disequilibrium in the region 71.80–71.87 Mb. This haplotype block contains one gene that may affect litter size, Histone Cell Cycle Regulator (HIRA. HIRA mRNA levels in sheep with different lambing ability were significantly higher in ovaries of Small Tail Han sheep (high fecundity than in Sunite sheep (low fecundity. Moreover, the expression levels of HIRA in eight tissues of uniparous Small Tail Han sheep were significantly higher than in multiparous Small Tail Han sheep (p < 0.05. HIRA SNPs significantly affect litter size in sheep and are useful as genetic markers for litter size.

The business environment and phases of development of small and medium-sized enterprises

OpenAIRE

Wach, Krzysztof

2006-01-01

The subject literature distinguishes several factors that determine the establishment, survival , operations and development of micro, small, and medium-sized enterprises in particular regions. In this article, the author presents a classification of these factors in terms of whether they are barriers or stimulators. On this basis, the author explains the influence of regional environment (meso-environment) factors on the development of small and medium-sized enterprises in various phases of ...

Size Exclusion HPLC Detection of Small-Size Impurities as a Complementary Means for Quality Analysis of Extracellular Vesicles

Directory of Open Access Journals (Sweden)

Tao Huang

2015-07-01

Full Text Available For extracellular vesicle research, whether for biomarker discoveries or therapeutic applications, it is critical to have high-quality samples. Both microscopy and NanoSight Tracking Analysis (NTA for size distribution have been used to detect large vesicles. However, there is currently no well-established method that is convenient for routine quality analysis of small-size impurities in vesicle samples. In this paper we report a convenient method, called ‘size-exclusion high-performance liquid chromatography’ (SE-HPLC, alongside NTA and Microscopy analysis to guide and qualify the isolation and processing of vesicles. First, the SE-HPLC analysis was used to detect impurities of small-size proteins during the ultra-centrifugation process of vesicle isolation; it was then employed to test the changes of vesicles under different pH conditions or integrity after storage. As SE-HPLC is generally accessible in most institutions, it could be used as a routine means to assist researchers in examining the integrity and quality of extracellular vesicles along with other techniques either during isolation/preparation or for further engineering and storage.

Strategic management in micro, small and medium-sized businesses in relation to financial success of the enterprise

Directory of Open Access Journals (Sweden)

Monika Švárová

2013-01-01

Full Text Available Small and medium sized enterprises play an essential role in the economy of the Czech Republic as a report of development of small and medium-sized enterprises and its support from 2010 announces. They are the source of development of towns, regions and the state itself. Small and medium-sized enterprises represent 99.84 % of the whole business subjects. Statistic data underline this position- they indicate that small and medium-sized enterprises employ 2/3 employees. Therefore, occupying small and medium-sized enterprises are to be taken as priority.Strategic management on the level of small and medium-sized enterprises is, as number of authors write, diverse. Small enterprises including micro have less access to capital, they have no money for employing specialists in the field, and they solve administration primarily. The aim of this follow-up GAJU project contribution concerned on process analysis of small and medium-sized enterprises is to summarize the gained results from the view of comparison of the level of strategic management in small and medium-sized enterprises.Nowadays, numbers of enterprises are thinking about whether they are able to remain in the market as an established company, they explore the possibility of improving its position. There is a question for small and medium-sized enterprises management- can strategic management be used as an instrument for increasing competitiveness? The results show that SMEs with a clearly defined strategy show better results of financial health (IN99 and ROA than companies without a defined strategy. In terms of business focus, we were able to demonstrate positive relationship between strategy and finance only for companies in the construction industry, on the significance level of 0.05. Compared to manufacturers and service-providing companies where this relation is not statistically significant.

Simplified analysis of passive residual heat removal systems for small size PWR's

International Nuclear Information System (INIS)

Botelho, D.A.

1992-02-01

The function and general objectives of a passive residual heat removal system for small size PWR's are defined. The characteristic configuration, the components and the operation modes of this system are concisely described. A preliminary conceptual specification of this system, for a small size PWR of 400 MW thermal, is made analogous to the decay heat removal system of the AP-600 reactor. It is shown by analytic models that such passive systems can dissipate 2% of nominal power within the thermal limits allowed to the reactor fuel elements. (author)

Regulation of Small and Medium-Sized Business Development in Russia: Problems and Solutions

Directory of Open Access Journals (Sweden)

Lyudmila Yuryevna Bogachkova

2015-12-01

Full Text Available The authors prove that despite the active state policy carried out since the second half of the 2000s and aimed at supporting small and medium-sized business in the Russian Federation, the current level of development of this economic sector is insufficient. The present paper characterizes the modern structure of small and medium-sized business. The authors show that the main problems hindering its growth are conditioned by low market demand, large tax deductions, numerous administrative barriers, lack of funding and state support. On the basis of the official data of Russian Federal State Statistics Service on theresults of annual surveys of entrepreneurs, the authors revealed the factors that prevented innovation situation in the country have stable negative impact on MSB, while the impact of such factors as imperfect legal and regulatory framework, investment risks, low profitability and inadequate state of technological infrastructure is relatively nonsignificant. The authors describe systemwide and resource measures of state regulation of small and medium-sized business. The system-wide measures include preferential access to production facilities and equipment, special tax regimes, administrative control. The measures of resource support to entrepreneurs consist in subsidizing the lease payments and interest rates on loans for the modernization of production; grant support, the establishment of microfinance organizations and guarantee funds, the development of business support infrastructure. The authors describe the forms of these measures implementation in 2013 and the main directions of improving the state regulation of small and medium-sized business, including the reduction of tax burden and facilitation of taxation procedures, the reduction of administrative barriers and ensuring access of small and medium-sized enterprises to government orders and technological infrastructure.

The Small Nuclear Genomes of Selaginella Are Associated with a Low Rate of Genome Size Evolution.

Science.gov (United States)

Baniaga, Anthony E; Arrigo, Nils; Barker, Michael S

2016-06-03

The haploid nuclear genome size (1C DNA) of vascular land plants varies over several orders of magnitude. Much of this observed diversity in genome size is due to the proliferation and deletion of transposable elements. To date, all vascular land plant lineages with extremely small nuclear genomes represent recently derived states, having ancestors with much larger genome sizes. The Selaginellaceae represent an ancient lineage with extremely small genomes. It is unclear how small nuclear genomes evolved in Selaginella We compared the rates of nuclear genome size evolution in Selaginella and major vascular plant clades in a comparative phylogenetic framework. For the analyses, we collected 29 new flow cytometry estimates of haploid genome size in Selaginella to augment publicly available data. Selaginella possess some of the smallest known haploid nuclear genome sizes, as well as the lowest rate of genome size evolution observed across all vascular land plants included in our analyses. Additionally, our analyses provide strong support for a history of haploid nuclear genome size stasis in Selaginella Our results indicate that Selaginella, similar to other early diverging lineages of vascular land plants, has relatively low rates of genome size evolution. Further, our analyses highlight that a rapid transition to a small genome size is only one route to an extremely small genome. © The Author 2016. Published by Oxford University Press on behalf of the Society for Molecular Biology and Evolution.

THE RELATIONSHIP MARKETING APPLICATION IN SMALL AND MEDIUM-SIZED ENTERPRISES

Directory of Open Access Journals (Sweden)

SABOU FELICIA

2016-12-01

Full Text Available The paper presents the importance of relationship marketing, the communication between customers and romanian small and medium-sized enterprises, analyzing also how are investigated and resolved the complaints received from the customers. In the paper, I made a study through I analyzed if the small and medium-sized enterprises undertake investigations about the reasons which they have lost customers. The study was conducted during january - february 2016, the main research methods used in the study were observation, documentation, analysis and market survey. Also, I chose the study questionnaire as research tool. From this study resulted that 79,31% of companies surveyed, were concerned and investigated the reasons they lost customers. Customer satisfaction is very important to business success, so it is recommended that companies must pay attention to the customers reactions and customers dissatisfaction consequences.

Node-pair reliability of network systems with small distances between adjacent nodes

International Nuclear Information System (INIS)

Malinowski, Jacek

2007-01-01

A new method for computing the node-pair reliability of network systems modeled by random graphs with nodes arranged in sequence is presented. It is based on a recursive algorithm using the 'sliding window' technique, the window being composed of several consecutive nodes. In a single step, the connectivity probabilities for all nodes included in the window are found. Subsequently, the window is moved one node forward. This process is repeated until, in the last step, the window reaches the terminal node. The connectivity probabilities found at that point are used to compute the node-pair reliability of the network system considered. The algorithm is designed especially for graphs with small distances between adjacent nodes, where the distance between two nodes is defined as the absolute value of the difference between the nodes' numbers. The maximal distance between any two adjacent nodes is denoted by Γ(G), where G symbolizes a random graph. If Γ(G)=2 then the method can be applied for directed as well as undirected graphs whose nodes and edges are subject to failure. This is important in view of the fact that many algorithms computing network reliability are designed for graphs with failure-prone edges and reliable nodes. If Γ(G)=3 then the method's applicability is limited to undirected graphs with reliable nodes. The main asset of the presented algorithms is their low numerical complexity-O(n), where n denotes the number of nodes

Targeting Triple Negative Breast Cancer with a Small-sized Paramagnetic Nanoparticle

Science.gov (United States)

Zhang, Li; Varma, Nadimpalli RS; Gang, Zhang Z.; Ewing, James R.; Arbab, Ali S; Ali, Meser M

2016-01-01

There is no available targeted therapy or imaging agent for triple negative breast cancer (TNBC). We developed a small-sized dendrimer-based nanoparticle containing a clinical relevant MRI contrast agent, GdDOTA and a NIR fluorescent dye, DL680. Systemic delivery of dual-modal nanoparticles led to accumulation of the agents in a flank mouse model of TNBC that were detected by both optical and MR imaging. In-vivo fluorescence images, as well as ex-vivo fluorescence images of individual organs, demonstrated that nanoparticles accumulated into tumor selectively. A dual modal strategy resulted in a selective delivery of a small-sized (GdDOTA)42-G4-DL680 dendrimeric agent to TNBC tumors, avoiding other major organs. PMID:28018751

Workplace Health Promotion within Small and Medium-Sized Enterprises

Science.gov (United States)

Moore, Ann; Parahoo, Kader; Fleming, Paul

2010-01-01

Purpose: The purpose of this study is to explore managers' understanding of workplace health promotion (WHP) and experiences of WHP activity within small and medium-sized enterprises (SMEs) in a Health and Social Care Trust area of Northern Ireland. The paper aims to focus on engagement with activities within the context of prevention of…

Financing Of Small And Medium-Size Enterprises In Cameroon ...

African Journals Online (AJOL)

Financing Of Small And Medium-Size Enterprises In Cameroon. ... Available data from the banking sector shows that as much as 78.7% of all ... SMEs and large companies pay back their loans better than the other ... Even the SME loan repayment rate of 62.9% is still low by World Bank ... AJOL African Journals Online.

The art of being small : brain-body size scaling in minute parasitic wasps

NARCIS (Netherlands)

Woude, van der Emma

2017-01-01

Haller’s rule states that small animals have relatively larger brains than large animals. This brain-body size relationship may enable small animals to maintain similar levels of brain performance as large animals. However, it also causes small animals to spend an exceptionally large proportion

Genotyping cows for the reference increase reliability of genomic prediction in a small breed

DEFF Research Database (Denmark)

Thomasen, Jørn Rind; Sørensen, Anders Christian; Lund, Mogens Sandø

2013-01-01

We hypothesized that adding cows to the reference population in a breed with a small number of reference bulls would increase reliabilities of genomic breeding values and genetic gain. We tested this premise by comparing two strategies for maintaining the reference population for genetic gain......, inbreeding and reliabilities of genomic predictions: 1) Adding 60 progeny tested bulls each year (B), and 2) in addition to 60 progeny tested bulls, adding 2,000 genotyped cows per year (C). Two breeding schemes were tested: 1) A turbo scheme (T) with only genotyped young bulls used intensively, and 2...... compared to the H-B, at the same level of ∆F. T-C yielded 15% higher ∆G compared t o T-B. Changing the breeding scheme from H-B to H-C increased ∆G by 5.5%. The lowest ∆F was observed with genotyping of cows. Reliabilities of GEBV in the C schemes showed a steep increase in reliability during the first...

Inverse Reliability Task: Artificial Neural Networks and Reliability-Based Optimization Approaches

OpenAIRE

Lehký , David; Slowik , Ondřej; Novák , Drahomír

2014-01-01

Part 7: Genetic Algorithms; International audience; The paper presents two alternative approaches to solve inverse reliability task – to determine the design parameters to achieve desired target reliabilities. The first approach is based on utilization of artificial neural networks and small-sample simulation Latin hypercube sampling. The second approach considers inverse reliability task as reliability-based optimization task using double-loop method and also small-sample simulation. Efficie...

Managers' Understanding of Workplace Health Promotion within Small and Medium-Sized Enterprises: A Phenomenological Study

Science.gov (United States)

Moore, Ann; Parahoo, Kader; Fleming, Paul

2011-01-01

Objective: This study aimed at exploring managers' understanding of workplace health promotion and experiences of workplace health promotion activity within small and medium-sized enterprises. Design: A Heideggerian interpretive phenomenological methodology was adopted. Setting: This study was undertaken with small and medium-sized enterprise…

Financial Management Challenges In Small And Medium-Sized Enterprises: A Strategic Management Approach

OpenAIRE

Hande Karadag

2015-01-01

Abstract :Due to their significant role in creation of new jobs, rise in GDP, entrepreneurship and innovation, small and medium-sized enterprises (SMEs) are recognized as the the drivers of socio-economic growth, both in developed and developing economies. In Turkey, 99.9 % of all enterprises fall into SME category. Therefore, the significance of SMEs for Turkish economy and society is much higher in Turkey, compared to other emerging and developed countries. Small and medium-sized companies ...

Test of a sample container for shipment of small size plutonium samples with PAT-2

International Nuclear Information System (INIS)

Kuhn, E.; Aigner, H.; Deron, S.

1981-11-01

A light-weight container for the air transport of plutonium, to be designated PAT-2, has been developed in the USA and is presently undergoing licensing. The very limited effective space for bearing plutonium required the design of small size sample canisters to meet the needs of international safeguards for the shipment of plutonium samples. The applicability of a small canister for the sampling of small size powder and solution samples has been tested in an intralaboratory experiment. The results of the experiment, based on the concept of pre-weighed samples, show that the tested canister can successfully be used for the sampling of small size PuO 2 -powder samples of homogeneous source material, as well as for dried aliquands of plutonium nitrate solutions. (author)

The Role of Branding in Small and Medium-Sized Enterprises

Directory of Open Access Journals (Sweden)

Franc Vidic

2013-12-01

Full Text Available The purpose of this article is to show the relationship between branding and brand management in small and medium-sized enterprises (SMEs. Traditionally, branding was associated with large and global corporations. However, we often forget that small and medium-sized enterprises also deal with their own names (brands in their own way. The study identified four types of businesses, regardless of their association with brands. We named these four types, as follows: Ignorant; User; Low-Cost Producer; and Differentiation Producer. If the first two types (i.e. Ignorant and User differ primarily in the extent to which they use simple branding activities, and are used mainly in the local market where the enterprises tend to operate, we found that the last two types (i.e. low-cost producers and differentiation producers design their branding strategies in accordance with their generic strategies and mode of growth.

Measures of small business success/performance: Importance, reliability and usability

Directory of Open Access Journals (Sweden)

Leković Božidar

2015-01-01

Full Text Available The main objective of this paper is to assess the reliability of selected measures of success/performance of small enterprises taking into account all the advantages and disadvantages of objective (traditional, financial and subjective (personal perception indicators. The realization of the basic objective will enable removal of doubt in different categories of success / performance of small businesses, which would be a secondary objective of the paper. The research methodology involves the use parametric procedures due to the characteristics of the selected variables and the number of observations in the sample. Univariate ANOVA and Pearson's coefficient correlation will be the main methods used. The basis of this study consists of data gathered from e-survey of 260 entrepreneurs/ owners/ managers of small enterprises in administrative sub-region of the Republic of Serbia. The analysis results show the correlation between subjective estimate of success of owners/ entrepreneurs/ managers and objective performance indicators, which can be characterized as complementary, meaning that subjective assessment as well as formally stated performance indicators are realistic. In addition, it is important to emphasize as an important result within the group of objective performance indicators, the differences between two groups, financial and non-financial, performance indicators.

Customer acquisition plan for a small-size entrepreneur

OpenAIRE

Puotiniemi, Tiia

2014-01-01

The aim of this thesis was to draw a customer acquisition plan and improve the marketing planning in the company. Therefore, the final result was the market research summary. Development of the marketing strategy planning was based on internal and external situation analyses. This thesis is concentrated on a small-size operator’s business and therefore the internet marketing was brought up with its profitable benefits and advantages. The thesis was written as an auxiliary guide to build u...

The role of micro size computing clusters for small physics groups

International Nuclear Information System (INIS)

Shevel, A Y

2014-01-01

A small physics group (3-15 persons) might use a number of computing facilities for the analysis/simulation, developing/testing, teaching. It is discussed different types of computing facilities: collaboration computing facilities, group local computing cluster (including colocation), cloud computing. The author discuss the growing variety of different computing options for small groups and does emphasize the role of the group owned computing cluster of micro size.

Analysis of near optimum design for small and medium size nuclear power plants

International Nuclear Information System (INIS)

Ahmed, A.A.

1977-01-01

Market surveys in recent years have shown that a significant market would exist among the developing nations of the world for nuclear power plants that would be classified as small to medium sized, provided that these small plants could produce electricity at a unit price comparable to that of equivalent sized fossil fired plants. Nuclear plants in the range of 100 MWe to 500 MWe would fit more effectively into the relatively smaller grids of most developing nations than would the 900 MWe to 1300 MWe units now being constructed in the large industrial nations. Worldwide re-evaluation of the worth of fossil fuels has prompted a re-examination of the competitive position of small to medium sized nuclear generating units compared to comparable fossil fired units, especially in the context of units specifically optimized for the size range of interest, rather than of designs that are simply scaled down versions of the currently available larger units. Since the absolute cost of electricity is more sensitive to external factors such as cost of money, national inflation rate and time required for licensing and construction than to details of design or perhaps even to choice of fuels, and since the cost of electricity generated in small to medium sized fossil fired units is periodically compared to that of scaled down versions of conventional large nuclear units, the point of view taken here is one of comparing the relative generating costs of smaller nuclear units of optimum design with the corresponding costs of scaled down versions of current large nuclear generating units

Mechanical stability of nanoporous metals with small ligament sizes

International Nuclear Information System (INIS)

Crowson, Douglas A.; Farkas, Diana; Corcoran, Sean G.

2009-01-01

Digital samples of nanoporous gold with small ligament sizes were studied by atomistic simulation using different interatomic potentials that represent varying surface stress values. We predict a surface relaxation driven mechanical instability for these materials. Plastic deformation is induced by the surface stress without external load, related to the combination of the surface stress value and the surface to volume ratio.

Small- and Medium-Sized Commercial Building Monitoring and Controls Needs: A Scoping Study

Energy Technology Data Exchange (ETDEWEB)

Katipamula, Srinivas; Underhill, Ronald M.; Goddard, James K.; Taasevigen, Danny J.; Piette, M. A.; Granderson, J.; Brown, Rich E.; Lanzisera, Steven M.; Kuruganti, T.

2012-10-31

Buildings consume over 40% of the total energy consumption in the U.S. A significant portion of the energy consumed in buildings is wasted because of the lack of controls or the inability to use existing building automation systems (BASs) properly. Much of the waste occurs because of our inability to manage and controls buildings efficiently. Over 90% of the buildings are either small-size (<5,000 sf) or medium-size (between 5,000 sf and 50,000 sf); these buildings currently do not use BASs to monitor and control their building systems from a central location. According to Commercial Building Energy Consumption Survey (CBECS), about 10% of the buildings in the U.S. use BASs or central controls to manage their building system operations. Buildings that use BASs are typically large (>100,000 sf). Lawrence Berkeley National Laboratory (LBNL), Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) were asked by the U.S. Department of Energy’s (DOE’s) Building Technologies Program (BTP) to identify monitoring and control needs for small- and medium-sized commercial buildings and recommend possible solutions. This study documents the needs and solutions for small- and medium-sized buildings.

Czech small and medium-sized enterprises and the success in foreign markets

Directory of Open Access Journals (Sweden)

Lenka Procházková

2011-01-01

Full Text Available The importance of small and medium-sized enterprises (SMEs in national economies has been growing. For these reasons, SME’s are paid more attention. The paper deals with the success of Czech SME’s activities in the foreign markets. These enterprises exploited the opportunity of extensive European Union market without internal borders and extended its activities to foreign markets. The objective of this paper is to determine characteristics related to activities carried on by small and medium-sized Czech companies in the foreign markets and then to describe those that fundamentally affect the success of these entities in the foreign markets. The characteristics are divided into five groups (a group of characteristics relating to the company, product, management, international experience and a group of characteristics relating to the target market. The enterprises’ success in foreign markets is assessed by aggregate indicator of success. This indicator is monitored by multi-dimensional indicators of corporate success and evaluation of both objective and subjective. At the last part of the article due to analysis of relationship used, there are identified characteristics affecting the success of Czech small and medium-sized enterprises in foreign markets.

The reliability and stability of visual working memory capacity.

Science.gov (United States)

Xu, Z; Adam, K C S; Fang, X; Vogel, E K

2018-04-01

Because of the central role of working memory capacity in cognition, many studies have used short measures of working memory capacity to examine its relationship to other domains. Here, we measured the reliability and stability of visual working memory capacity, measured using a single-probe change detection task. In Experiment 1, the participants (N = 135) completed a large number of trials of a change detection task (540 in total, 180 each of set sizes 4, 6, and 8). With large numbers of both trials and participants, reliability estimates were high (α > .9). We then used an iterative down-sampling procedure to create a look-up table for expected reliability in experiments with small sample sizes. In Experiment 2, the participants (N = 79) completed 31 sessions of single-probe change detection. The first 30 sessions took place over 30 consecutive days, and the last session took place 30 days later. This unprecedented number of sessions allowed us to examine the effects of practice on stability and internal reliability. Even after much practice, individual differences were stable over time (average between-session r = .76).

International Financial Reporting standard for Small and Medium-sized entities

Directory of Open Access Journals (Sweden)

Z Koppeschaar

2012-12-01

Full Text Available The International Financial Reporting Standard for Small and Medium-sized entities (IFRS for SMEs was published as a standard by the International Accounting Standards Board (IASB during July 2009. During 2007 South Africa became one of the first countries and the first country in Africa to early accept the proposed accounting standard (exposure draft of an IFRS for SMEs. The accounting standard will probably also be accepted by numerous other countries. The aim of this article is to investigate the applicability of this accounting standard. The results indicated that the IFRS for SMEs remains too comprehensive for the majority of small companies. The IFRS for SMEs does not satisfy the needs of South African users of small company financial statements, and as a result the accounting requirements should be simplified. KEYWORDS: Financial accounting; Financial reporting requirements; IFRS for SMEs; Small companies; Users of financial statements; Small company financial statements.

75 FR 9431 - Small and Medium-Sized Enterprises: U.S. and EU Export Activities, and Barriers and Opportunities...

Science.gov (United States)

2010-03-02

... to the USTR on the first investigation, No. 332-508, Small and Medium-Sized Enterprises: Overview of..., investigation No. 332-509, Small and Medium-Sized Enterprises: U.S. and EU Export Activities, and Barriers and Opportunities Experienced by U.S. Firms, and investigation No. 332- 510, Small and Medium-Sized Enterprises...

System reliability of corroding pipelines

International Nuclear Information System (INIS)

Zhou Wenxing

2010-01-01

A methodology is presented in this paper to evaluate the time-dependent system reliability of a pipeline segment that contains multiple active corrosion defects and is subjected to stochastic internal pressure loading. The pipeline segment is modeled as a series system with three distinctive failure modes due to corrosion, namely small leak, large leak and rupture. The internal pressure is characterized as a simple discrete stochastic process that consists of a sequence of independent and identically distributed random variables each acting over a period of one year. The magnitude of a given sequence follows the annual maximum pressure distribution. The methodology is illustrated through a hypothetical example. Furthermore, the impact of the spatial variability of the pressure loading and pipe resistances associated with different defects on the system reliability is investigated. The analysis results suggest that the spatial variability of pipe properties has a negligible impact on the system reliability. On the other hand, the spatial variability of the internal pressure, initial defect sizes and defect growth rates can have a significant impact on the system reliability.

Theory of flotation of small and medium-size particles

Science.gov (United States)

Derjaguin, B. V.; Dukhin, S. S.

1993-08-01

The paper describes a theory of flotation of small and medium-size particles less than 50μ in radius) when their precipitation on a bubble surface depends more on surface forces than on inertia forces, and deformation of the bubble due to collisions with the particles may be neglected. The approach of the mineral particle to the bubble surface is regarded as taking place in three stages corresponding to movement of the particles through zones 1, 2 and 3. Zone 3 is a liquid wetting layer of such thickness that a positive or negative disjoining pressure arises in this intervening layer between the particle and the bubble. By zone 2 is meant the diffusional boundary layer of the bubble. In zone 1, which comprises the entire liquid outside zone 2, there are no surface forces. Precipitation of the particles is calculated by considering the forces acting in zones 1, 2 and 3. The particles move through zone 1 under the action of gravity and inertia. Analysis of the movement of the particles under the action of these forces gives the critical particle size, below which contact with the bubble surface is impossible, if the surface forces acting in zones 2 and 3 be neglected. The forces acting in zone 2 are ‘diffusio-phoretic’ forces due to the concentration gradient in the diffusional boundary layer. The concentration and electric field intensity distribution in zone 2 is calculated, taking into account ion diffusion to the deformed bubble surface. An examination is made of the ‘equilibrium’ surface forces acting in zone 3 independent of whether the bubble is at rest or in motion. These forces, which determine the behaviour of the thin wetting intervening layer between the bubble and the mineral particle and the height of the force barrier against its rupture, may be represented as results of the disjoining pressure forces acting on various parts of the film. The main components of the disjoining pressure are van der Waals forces, forces of an iono

Mid-level perceptual features distinguish objects of different real-world sizes.

Science.gov (United States)

Long, Bria; Konkle, Talia; Cohen, Michael A; Alvarez, George A

2016-01-01

Understanding how perceptual and conceptual representations are connected is a fundamental goal of cognitive science. Here, we focus on a broad conceptual distinction that constrains how we interact with objects--real-world size. Although there appear to be clear perceptual correlates for basic-level categories (apples look like other apples, oranges look like other oranges), the perceptual correlates of broader categorical distinctions are largely unexplored, i.e., do small objects look like other small objects? Because there are many kinds of small objects (e.g., cups, keys), there may be no reliable perceptual features that distinguish them from big objects (e.g., cars, tables). Contrary to this intuition, we demonstrated that big and small objects have reliable perceptual differences that can be extracted by early stages of visual processing. In a series of visual search studies, participants found target objects faster when the distractor objects differed in real-world size. These results held when we broadly sampled big and small objects, when we controlled for low-level features and image statistics, and when we reduced objects to texforms--unrecognizable textures that loosely preserve an object's form. However, this effect was absent when we used more basic textures. These results demonstrate that big and small objects have reliably different mid-level perceptual features, and suggest that early perceptual information about broad-category membership may influence downstream object perception, recognition, and categorization processes. (c) 2015 APA, all rights reserved).

77 FR 72691 - Small Business Size Standards: Administrative and Support, Waste Management and Remediation Services

Science.gov (United States)

2012-12-06

... importantly, the Small Business Act requires SBA to establish one definition of what is a small business... SMALL BUSINESS ADMINISTRATION 13 CFR Part 121 RIN 3245-AG27 Small Business Size Standards: Administrative and Support, Waste Management and Remediation Services AGENCY: U.S. Small Business Administration...

Accounting standards for small and medium-sized entities. Evidence from Spain

OpenAIRE

Milanés Montero Patricia; Albarrán Lozano Irene; Texeira Quirós Joaquín; Esteban Pérez Calderón

2011-01-01

By approving Regulation 1606/2002, the European Commission entrusts the local European Union regulators with the difficult decision as to whether making the International Accounting Standards (IAS/IFRS) extensive for their Small and Medium sized Entities or not. International Financial Reporting Standard for Small and Medium-sizzed Entities (hereinafter IFRS for SMEs) was published in 2009, and the European Commission had also decided to seek the opinion of EU stakeholders on this Standard. W...

Graduate Student in Engineering, Hoped by Owners of Medium-and Small-Sized Companies

Science.gov (United States)

Kida, Yoshihiro

Medium-and small-sized companies have held up Japanese technologies which situated top level in the world as far. However, for the technologies of medium-and small-sized companies to keep the top-level in the 21 centuries, researchers and engineers are demand to have high technologies. Those engineers are hoped for to have not only “knowledge”, but also “creativity, feeling and experience”. Therefore, in order to create such professional engineers, educational institute must have a function by which a practical training and education can be conducted.

Safety Analysis for Medium/Small Size Integral Reactor: Evaluation of Safety Characteristics for Small and Medium Integral Reactor

Energy Technology Data Exchange (ETDEWEB)

Kim, Hho jung; Seul, K W; Ahn, S K; Bang, Y S; Park, D G; Kim, B K; Kim, W S; Lee, J H; Kim, W K; Shim, T M; Choi, H S; Ahn, H J; Jung, D W; Kim, G I; Park, Y M; Lee, Y J [Korea Inst. of Nuclear Safety, Taejon (Korea, Republic of)

1997-07-01

The Small and medium integral reactor is developed to be utilized for non-electric areas such as district heating and steam production for desalination and other industrial purposes, and then these applications may typically imply a closeness between the reactor and the user. It requires the reactor to be designed with the adoption of special functional and inherent safety features to ensure and promote a high level of safety and reliability, in comparison with the existing nuclear power plants. The objective of the present study is to establish the bases for the development of regulatory requirements and technical guides to address the special safety characteristics of the small and medium integral reactor. In addition, the study aims to identify and to propose resolutions to the possible safety concerns in the design of the small and medium integral reactor. 34 refs., 20 tabs. (author)

Small Scale Yielding Correction of Constraint Loss in Small Sized Fracture Toughness Test Specimens

International Nuclear Information System (INIS)

Kim, Maan Won; Kim, Min Chul; Lee, Bong Sang; Hong, Jun Hwa

2005-01-01

Fracture toughness data in the ductile-brittle transition region of ferritic steels show scatter produced by local sampling effects and specimen geometry dependence which results from relaxation in crack tip constraint. The ASTM E1921 provides a standard test method to define the median toughness temperature curve, so called Master Curve, for the material corresponding to a 1T crack front length and also defines a reference temperature, T 0 , at which median toughness value is 100 MPam for a 1T size specimen. The ASTM E1921 procedures assume that high constraint, small scaling yielding (SSY) conditions prevail at fracture along the crack front. Violation of the SSY assumption occurs most often during tests of smaller specimens. Constraint loss in such cases leads to higher toughness values and thus lower T 0 values. When applied to a structure with low constraint geometry, the standard fracture toughness estimates may lead to strongly over-conservative estimates. A lot of efforts have been made to adjust the constraint effect. In this work, we applied a small-scale yielding correction (SSYC) to adjust the constraint loss of 1/3PCVN and PCVN specimens which are relatively smaller than 1T size specimen at the fracture toughness Master Curve test

Large- and small-size advantages in sneaking behaviour in the dusky frillgoby Bathygobius fuscus

OpenAIRE

Takegaki, Takeshi; Kaneko, Takashi; Matsumoto, Yukio

2012-01-01

Sneaking tactic, a male alternative reproductive tactic involving sperm competition, is generally adopted by small individuals because of its inconspicuousness. However, large size has an advantage when competition occurs between sneakers for fertilization of eggs. Here, we suggest that both large- and small-size advantages of sneaker males are present within the same species. Large sneaker males of the dusky frillgoby Bathygobius fuscus showed a high success rate in intruding into spawning n...

Reliability and validity of food portion size estimation from images using manual flexible digital virtual meshes

Science.gov (United States)

The eButton takes frontal images at 4 second intervals throughout the day. A three-dimensional (3D) manually administered wire mesh procedure has been developed to quantify portion sizes from the two-dimensional (2D) images. This paper reports a test of the interrater reliability and validity of use...

Subureteral Injection with Small-Size Dextranomer/Hyaluronic Acid Copolymer: Is It Really Efficient?

Directory of Open Access Journals (Sweden)

Iyimser Üre

2016-01-01

Full Text Available The aim of this study was to evaluate the clinical results of patients with vesicoureteral reflux, which were treated with subureteral injection of small-size (80–120 μm dextranomer/hyaluronic acid copolymer (Dx/HA. Data of 75 children (105 renal units who underwent STING procedure with small-size Dx/HA for the treatment of vesicoureteral reflux (VUR in our clinic between 2008 and 2012 were retrospectively analyzed. Preoperative reflux grade and side, injection indication, postoperative urinary infections and urinary symptoms, voiding cystourethrogram, and renal scintigraphy results were evaluated. The success rate of the procedure was 100% in patients with grades 1 and 2 reflux, 91% in patients with grade 3 reflux, and 82.6% in patients with grade 4. Overall success rate of the treated patients was 97%. Endoscopic subureteric injection with Dx/HA procedure has become a reasonable minimally invasive alternative technique to open surgery, long-term antibiotic prophylaxis, and surveillance modalities in treatment of VUR in terms of easy application, low costs and complication rates, and high success rates. Injection material composed of small-size dextranomer microspheres seems superior to normal size Dx/HA, together with offering similar success with low cost.

Pen size and parity effects on maternal behaviour of Small-Tail Han sheep.

Science.gov (United States)

Lv, S-J; Yang, Y; Dwyer, C M; Li, F-K

2015-07-01

The aim of this experiment was to study the effects of pen size and parity on maternal behaviour of twin-bearing Small-Tail Han ewes. A total of 24 ewes were allocated to a 2×2 design (six per pen), with parity (primiparous or multiparous) and pen size (large: 6.0×3.0 m; small: 6.0×1.5 m) as main effects at Linyi University, Shandong Province, China. Behaviour was observed from after parturition until weaning. All ewes were observed for 6 h every 5 days from 0700 to1000 h and from 1400 to 1700 h. Continuous focal animal sampling was used to quantify the duration of maternal behaviours: sucking, grooming and following as well as the frequency of udder accepting, udder refusing and low-pitched bleating. Oestradiol and cortisol concentrations in the faeces (collected in the morning every 5 days) were detected using EIA kits. All lambs were weighed 24 h after parturition and again at weaning at 35 days of age. The small pen size significantly reduced following (Pbehaviour in sheep during lactation. The study is also the first to report on the maternal behaviour of Chinese native sheep breeds (Small-Tail Han sheep), with implications for the production of sheep in China.

The Impact of their Adoption on Small and Medium-sized Enterprises

International Development Research Centre (IDRC) Digital Library (Canada)

... of small and medium-sized enterprises (SMEs) as well as the impact of these ... of Mathematics and Industrial Engineering at the École Polytechique, Montréal. Dr Lefebvre's research focuses on technological innovation and the strategic ...

International seminar on status and prospects for small and medium sized reactors. Book of extended synopses

International Nuclear Information System (INIS)

2001-05-01

Small and medium sized reactors have been defined by IAEA in accordance with their net electrical power rating, or thermal equivalent power rating for reactors producing process heat. Within the global energy supply and demand the role of nuclear power, and specifically the role of small and medium sizes reactors, is reviewed. Some new design prospects of dual purpose power plants, namely for heat production and desalination, are presented. Some proposal for new concepts of small size power reactors are described. A special concern is devoted to economic and energy policy issues as well as to safety and non-proliferation matters

Statistical issues in reporting quality data: small samples and casemix variation.

Science.gov (United States)

Zaslavsky, A M

2001-12-01

To present two key statistical issues that arise in analysis and reporting of quality data. Casemix variation is relevant to quality reporting when the units being measured have differing distributions of patient characteristics that also affect the quality outcome. When this is the case, adjustment using stratification or regression may be appropriate. Such adjustments may be controversial when the patient characteristic does not have an obvious relationship to the outcome. Stratified reporting poses problems for sample size and reporting format, but may be useful when casemix effects vary across units. Although there are no absolute standards of reliability, high reliabilities (interunit F > or = 10 or reliability > or = 0.9) are desirable for distinguishing above- and below-average units. When small or unequal sample sizes complicate reporting, precision may be improved using indirect estimation techniques that incorporate auxiliary information, and 'shrinkage' estimation can help to summarize the strength of evidence about units with small samples. With broader understanding of casemix adjustment and methods for analyzing small samples, quality data can be analysed and reported more accurately.

76 FR 63509 - Small Business Size Standards: Administrative and Support, Waste Management and Remediation Services

Science.gov (United States)

2011-10-12

... Federal small business assistance, SBA establishes small business definitions (referred to as size... operated, (2) not dominant in its field of operation, and (3) within a specific small business definition... Vol. 76 Wednesday, No. 197 October 12, 2011 Part VI Small Business Administration 13 CFR Part 121...

Is radiographic measurement of bony landmarks reliable for lateral meniscal sizing?

Science.gov (United States)

Yoon, Jung-Ro; Kim, Taik-Seon; Lim, Hong-Chul; Lim, Hyung-Tae; Yang, Jae-Hyuk

2011-03-01

radiologic measurement showed good reliability (intraclass correlation coefficients, .823 to .973). The authors tried to determine the best-fit equation for predicting meniscal size from Pollard's method of bone size, as follows: anatomic length = 0.52 × plateau length (according to Pollard's method) + 5.2, not as Pollard suggested (0.7 × Pollard's plateau length). Based on this equation-namely, the modified Pollard method-the percentage difference decreased, and the accuracy increased to 92%. Lateral meniscal length dimension can be accurately predicted from the authors' radiographic tibial plateau measurements. This study may provide valuable information in preoperative sizing of lateral meniscus in meniscal allograft transplantation.

Small Business Size Standards

Data.gov (United States)

Small Business Administration — Certain government programs, such as SBA loan programs and contracting opportunities, are reserved for small business concerns. In order to qualify, businesses must...

Multislice helical CT analysis of small-sized airway wall thickness in smokers and patients with bronchial asthma

International Nuclear Information System (INIS)

Sekimura, Kenshi; Ito, Harumasa; Nakamura, Yutaka; Kobayashi, Hitoshi; Oikawa, Hirobumi; Inoue, Hiroshi; Ehara, Shigeru; Yamauchi, Kohei

2010-01-01

There is accumulating evidence that airway remodeling, which contributes to airway narrowing, plays a role in the pathogenesis of bronchial asthma (BA) and chronic obstructive pulmonary disease (COPD). Development of the multislice helical CT (MSCT) with improved spatial resolution has made it possible to obtain more precise imaging of small-sized airways. Small-sized airway wall-thickness was measured using the MSCT scan to analyze small-sized airways of smokers and BA patients, and examine the effects of a β 2 agonists on small-sized airway wall-thickness of BA patients. Thirty-six non-asthmatics who participated in the Health Check Program of Iwate Medical University and 25 patients with asthma were recruited. Amongst the 36 non-asthmatics were 20 healthy never-smokers and 15 smokers. The other 25 asthmatics were recruited from the outpatient clinic at Iwate Medical University. MSCT was performed and the right B10 bronchus was chosen for dimensional analysis. Airway wall thickness was expressed as a percentage of wall area (WA%). WA% of the 7 asthmatics before and 30 mim after procaterol (20μg) inspiration were compared. Small-sized airway wall thickness was significantly increased in smokers and patients with asthma compared to healthy never-smokers, when determined by MSCT. Both %V 50 and %V 25 had significant negative correlations with WA% among the healthy never-smokers and smoker population. Procaterol inspiration reduced WA% in the small airway of patients with asthma. Increase of small-sized airway thickness measured by MSCT scan may reflect peripheral obstructive lesions of smokers and BA patients. (author)

High temperature salting of mince of small sized fish

OpenAIRE

Sorinmade, S.O.; Talabi, S.O.; Aliu, A.

1982-01-01

Freshly caught small sized fish species were transported to the laboratory gutted and washed before mechanical separation into bone and mince. Duplicate batches of the mince were then treated with seven different concentrations (wt/wt) of sodium chloride before cooking. The cooked mince was divided into two groups, pressed and unpressed. Percentage residual salt in the salted cooked mince, free and press water and salted cooked pressed mince were determined. Also, the moisture contents of...

Sales strategy in small and medium-sized food companies

DEFF Research Database (Denmark)

Nielsen, Renate; Stacey, Julia; Andersen, Lone Merete Schreiber

2002-01-01

All managing teams know that they have to deal with the company's strategy in handling the market. But how do they do it and on the basis of which beleifs and interpretations? A nearly completed PhD project has examined the way in which three small and medium-sized food companies define...... their market, their competitors and customers, and how they create the world they perceive and act in through their own actions....

Effects of corridors on home range sizes and interpatch movements of three small mammal species.

Energy Technology Data Exchange (ETDEWEB)

Mabry, Karen, E.; Barrett, Gary, W.

2002-04-30

Mabry, K.E., and G.W. Barrett. 2002. Effects of corridors on home range sizes and interpatch movements of three small mammal species. Landscape Ecol. 17:629-636. Corridors are predicted to benefit populations in patchy habitats by promoting movement, which should increase population densities, gene flow, and recolonization of extinct patch populations. However, few investigators have considered use of the total landscape, particularly the possibility of interpatch movement through matrix habitat, by small mammals. This study compares home range sizes of 3 species of small mammals, the cotton mouse, old field mouse and cotton rat between patches with and without corridors. Corridor presence did not have a statistically significant influence on average home range size. Habitat specialization and sex influenced the probability of an individual moving between 2 patches without corridors. The results of this study suggest that small mammals may be more capable of interpatch movement without corridors than is frequently assumed.

HRM implications for network collaboration of small and medium sized companies

DEFF Research Database (Denmark)

Kesting, Peter; Müller, Sabine; Jørgensen, Frances

Collaboration in innovation networks is particularly important for small and medium enterprises (SMEs) to remain competitive in a rapidly changing environment. Collaboration may however be particularly challenging for SMEs, due to their size and their inherent shortage of resources. In this paper...

Conceptual design of small-sized HTGR system (1). Major specifications and system designs

International Nuclear Information System (INIS)

Ohashi, Hirofumi; Sato, Hiroyuki; Tazawa, Yujiro; Yan, Xing L.; Tachibana, Yukio

2011-06-01

Japan Atomic Energy Agency (JAEA) has started a conceptual design of a 50MWt small-sized high temperature gas cooled reactor (HTGR) for steam supply and electricity generation (HTR50S), which is a first-of-kind of the commercial plant or a demonstration plant of a small-sized HTGR system for steam supply to the industries and district heating and electricity generation by a steam turbine, to deploy in developing countries in the 2030s. The design philosophy is that the HTR50S is a high advanced reactor, which is reducing the R and D risk based on the HTTR design, upgrading the performance and reducing the cost for commercialization by utilizing the knowledge obtained by the HTTR operation and the GTHTR300 design. The major specifications of the HTR50S were determined and targets of the technology demonstration using the HTR50S (e.g., the increasing the power density, reduction of the number of uranium enrichment in the fuel, increasing the burn up, side-by-side arrangement between the reactor pressure vessel and the steam generator) were identified. In addition, the system design of HTR50S, which offers the capability of electricity generation, cogeneration of electricity and steam for a district heating and industries, was performed. Furthermore, a market size of small-sized HTGR systems was investigated. (author)

Favouring Small and Medium Sized Enterprises with Directive 2014/24/EU

DEFF Research Database (Denmark)

Trybus, Martin; Andrecka, Marta

2017-01-01

This article argues that the four main measures introduced in the 2014 reform of the Procurement Directives to promote Small andMediumSized Enterprises (SMEs) cannot be classified as measures favouring SMEs. A measure favours SMEs when it compromises the main objectives of competition, non...

Risk assessment of small-sized HTR with pebble-bed core

International Nuclear Information System (INIS)

Kroeger, W.; Mertens, J.; Wolters, J.

1987-01-01

Two recent concepts of small-sized HTR's (HTR-Modul and HTR-100) were analysed regarding their safety concepts and risk protection. In neither case do core cooling accidents contribute to the risk because of the low induced core temperatures. Water ingress accidents dominate the risk in both cases by detaching deposited fission products which can be released into the environment. For these accident sequences no early fatalities and practically no lethal case of cancer were computed. Both HTR concepts include adequate precautionary measures and an infinitely small risk according to the usual standards. The safety concepts make express use of the specific inherent safety features of pebble-bed HTR's. (orig.)

SMALL AND MEDIUM-SIZED ENTERPRISES IN REPUBLIC OF MOLDOVA

Directory of Open Access Journals (Sweden)

Igor G. SÎRODOEV

2009-12-01

Full Text Available The paper examines the role of SME sector in Moldova’s economy and its likely implications in the RD processes. There are emphasized several key features of the relationship between knowledge economy, RD and SMEs, and their effect on regional and local communities. Then, a summary of RD particular features in Moldova is presented.The role of SME sector, examined in terms of its performance by ownership and activity types, as a whole and by main firms’ categories (micro-, small, and medium-sized is analyzed. Small enterprises have been considered as the most adequate solution forpromoting RD in general case. National-level analysis is completed by regional insight into the sector as a whole. Finally, some critical aspects of SMEs’ role in RD in Moldova are discussed.

More Differences or More Similarities Regarding Education in Big, Middle-sized and Small Companies

Directory of Open Access Journals (Sweden)

Marjana Merkač

2001-12-01

Full Text Available The article presents the results of research of education and qualifying of employees in small, middle-sized and big Slovenian companies. The research shows some differences regarding the attitude to the development of employees as a part of a company's business strategy, some obstacles for developing their abilities, and connections between job satisfaction and motivation for learning. It also shows how important it is for the subjects concerning education and qualifying if an individual works for a big, middle-sized, or small company.

How big is big and how small is small the sizes of everything and why

CERN Document Server

Smith, Timothy Paul

2013-01-01

This book is about how big is the universe and how small are quarks, and what are the sizes of dozens of things between these two extremes. It describes the sizes of atoms and planets, quarks and galaxies, cells and sequoias. It is a romp through forty-five orders of magnitude from the smallest sub-nuclear particles we have measured, to the edge of the observed universe. It also looks at time, from the epic age of the cosmos to the fleeting lifetimes of ethereal particles. It is a narrative that trips its way from stellar magnitudes to the clocks on GPS satellites, from the nearly logarithmic scales of a piano keyboard through a system of numbers invented by Archimedes and on to the measurement of the size of an atom. Why do some things happen at certain scales? Why are cells a hundred thousandths of a meter across? Why are stars never smaller than about 100 million meters in diameter? Why are trees limited to about 120 meters in height? Why are planets spherical, but asteroids not? Often the size of an objec...

Utilizing Content Marketing in Small and Medium-Sized Organizations

OpenAIRE

Parviainen, Ville

2014-01-01

The major objective of this study is to find out how and to what extent online content is currently utilized for marketing purposes among small and medium-sized organizations in Finland. Additionally, positive and negative future prospects concerning this type of content marketing were explored. The study is mainly qualitative by nature. The empirical part of this thesis was carried out between July 2013 and March 2014 and it consists of five semi-structured interviews with five professio...

Design features to achieve defence-in-depth in small and medium sized reactors

International Nuclear Information System (INIS)

Kuznetsov, Vladimir

2009-01-01

Broader incorporation of inherent and passive safety design features has become a 'trademark' of many advanced reactor concepts, including several evolutionary designs and nearly all innovative small and medium sized design concepts. Ensuring adequate defence-in-depth is important for reactors of smaller output because many of them are being designed to allow more proximity to the user, specifically, when non-electrical energy products are targeted. Based on the activities recently performed by the International Atomic Energy Agency, the paper provides a summary description of the design features used to achieve defence in depth in the eleven representative concepts of small and medium sized reactors. (author)

Reliability of risk-adjusted outcomes for profiling hospital surgical quality.

Science.gov (United States)

Krell, Robert W; Hozain, Ahmed; Kao, Lillian S; Dimick, Justin B

2014-05-01

Quality improvement platforms commonly use risk-adjusted morbidity and mortality to profile hospital performance. However, given small hospital caseloads and low event rates for some procedures, it is unclear whether these outcomes reliably reflect hospital performance. To determine the reliability of risk-adjusted morbidity and mortality for hospital performance profiling using clinical registry data. A retrospective cohort study was conducted using data from the American College of Surgeons National Surgical Quality Improvement Program, 2009. Participants included all patients (N = 55,466) who underwent colon resection, pancreatic resection, laparoscopic gastric bypass, ventral hernia repair, abdominal aortic aneurysm repair, and lower extremity bypass. Outcomes included risk-adjusted overall morbidity, severe morbidity, and mortality. We assessed reliability (0-1 scale: 0, completely unreliable; and 1, perfectly reliable) for all 3 outcomes. We also quantified the number of hospitals meeting minimum acceptable reliability thresholds (>0.70, good reliability; and >0.50, fair reliability) for each outcome. For overall morbidity, the most common outcome studied, the mean reliability depended on sample size (ie, how high the hospital caseload was) and the event rate (ie, how frequently the outcome occurred). For example, mean reliability for overall morbidity was low for abdominal aortic aneurysm repair (reliability, 0.29; sample size, 25 cases per year; and event rate, 18.3%). In contrast, mean reliability for overall morbidity was higher for colon resection (reliability, 0.61; sample size, 114 cases per year; and event rate, 26.8%). Colon resection (37.7% of hospitals), pancreatic resection (7.1% of hospitals), and laparoscopic gastric bypass (11.5% of hospitals) were the only procedures for which any hospitals met a reliability threshold of 0.70 for overall morbidity. Because severe morbidity and mortality are less frequent outcomes, their mean

Continuing Education for Managers from Small and Medium Sized German Companies.

Science.gov (United States)

Fub, Jorg

1995-01-01

An international trade school in southern Germany, which is a highly export-oriented environment, has established a vocational and professional continuing education program for personnel of small- and medium-size companies. Offerings include a graduate course in international marketing, seminars for export companies, distance education in…

Specifics of Management in Small and Medium-Size Enterprises in Serbia

Directory of Open Access Journals (Sweden)

Marija Lazarević-Moravčević

2014-12-01

Full Text Available Under modern conditions for performing business, an enterprise regardless of its size or business activity must be systematically directed and run. Small and medium-size enterprises have certain characteristics that make them considerably different compared to large systems, therefore it is not realistic to expect that the management process in such organizations would develop in the same way as in the large systems. The fact is that the small business often does not involve a small investment, and the management of small enterprises is constantly faced with the problem of "poverty of resources" that leads to the conclusion that the success of SMEs is predominantly determined by the managerial skills of managers/owners. Assuming that the owners/managers of SMEs adequately perceive the capabilities of their enterprise, make the right decisions, finding effective solutions in terms of organization and apply modern approaches to control and the success of the company definitely will follow. In this paper theoretical and empirical research has been carried out with the aim to identify the basic characteristics of successful management of SMEs in Serbia. The research results indicate that the managerial capacity of managers/owners of SMEs is the main strength of the company, and one of the key sources of growth and development. When the influence of external factors is very unfavorable for business development, the management as an internal resource of organization is increasingly gaining importance in creating business success and competitive advantage.

Development of design program for small-sized gas absorption chiller/heaters

Energy Technology Data Exchange (ETDEWEB)

Yoon, J.I.; Kwon, O.K.; Moon, C.K. [Pukyong National University, Pusan (Korea); Yang, Y.M.; Kim, H.Y. [R and D Center, Korea Gas Corporation, Ansan (Korea)

1999-10-01

Analysis of basic data is performed for development of small size water-cooled household absorption chiller/heater using non CFC refrigerant, analytic simulation program of air cooling performance is developed that system has 1.5-10RT of air cooling performance, we perform cycle analysis and numerical simulation. We develope a performance analysis of simulation program to perform a basic design for 1.5-10RT apparatus of small size system of development model in gas driven double effect absorption chiller/heater. The system working condition and operation limit condition is decided from the existing data which is analyzed and the conference with KOGAS. After the basic input variable and regular condition is established for heat cycle analysis, the simulation algorithm is set up and performance simulation program is coded according to the organized algorithm. The basic design of optimum system is completed from parametric study using developed simulation program and establishing the design variable range of developing object model. 20 refs., 30 figs., 9 tabs.

THE POSSIBILITY OF USING INTERNATIONAL EXPERIENCE IN MICRO-CREDIT FOR SMALL AND MEDIUM-SIZED INDUSTRIAL ENTERPRISES

Directory of Open Access Journals (Sweden)

I. N. Klyukin

2016-01-01

Full Text Available Purpose of the study. Increasing the availability of funding for small and medium-sized enterprises of the industrial sector put among the most important tasks of economic development as the leading developed countries, and developing countries. In connection with the above, the purpose of this article is to study the micro-credit as an efficient mechanism to stimulate the development of small and medium-sized industrial enterprises and analyzing the possibility of using foreign experience in improving the process of micro-credit to stimulate their development.Research Methodology. The study was conducted on the material of publications on various aspects of the microcredit industry small and medium businesses, including international experience in micro-credit for small and medium-sized industrial enterprises.The article analyzes the functioning of the various models and micro-technologies, disclosed interoperability of commercial banks and microfinance institutions (MFIs in the framework of country-specific microcredit models, and formulated the immediate tasks and activities of the government and regulatory authorities of the Russian Federation aimed at improving the financing of small and medium-sized industrial enterprises.Sounding the findings suggest that the funds to support small and medium-sized industrial enterprises should be more actively attract private investment in the implementation of industrial and innovative development of their projects. In this case, the intensification of financial-credit and investment support to small and medium-sized industrial enterprises, integration and optimization of the different sources of financial resources create favorable conditions for their access to financial and credit resources, and improvement of financial and credit support mechanisms will enhance their responsibility for use granted resources and contribute to their development. At the same time, the main focus of the use of public

Born small, die young: Intrinsic, size-selective mortality in marine larval fish

KAUST Repository

Garrido, S.

2015-11-24

Mortality during the early stages is a major cause of the natural variations in the size and recruitment strength of marine fish populations. In this study, the relation between the size-at-hatch and early survival was assessed using laboratory experiments and on field-caught larvae of the European sardine (Sardina pilchardus). Larval size-at-hatch was not related to the egg size but was significantly, positively related to the diameter of the otolith-at-hatch. Otolith diameter-at-hatch was also significantly correlated with survival-at-age in fed and unfed larvae in the laboratory. For sardine larvae collected in the Bay of Biscay during the spring of 2008, otolith radius-at-hatch was also significantly related to viability. Larval mortality has frequently been related to adverse environmental conditions and intrinsic factors affecting feeding ability and vulnerability to predators. Our study offers evidence indicating that a significant portion of fish mortality occurs during the endogenous (yolk) and mixed (yolk /prey) feeding period in the absence of predators, revealing that marine fish with high fecundity, such as small pelagics, can spawn a relatively large amount of eggs resulting in small larvae with no chances to survive. Our findings help to better understand the mass mortalities occurring at early stages of marine fish.

Born small, die young: Intrinsic, size-selective mortality in marine larval fish

KAUST Repository

Garrido, S.; Ben-Hamadou, R.; Santos, A.M.P.; Ferreira, S.; Teodó sio, M.A.; Cotano, U.; Irigoien, Xabier; Peck, M.A.; Saiz, E.; Ré , P.

2015-01-01

Mortality during the early stages is a major cause of the natural variations in the size and recruitment strength of marine fish populations. In this study, the relation between the size-at-hatch and early survival was assessed using laboratory experiments and on field-caught larvae of the European sardine (Sardina pilchardus). Larval size-at-hatch was not related to the egg size but was significantly, positively related to the diameter of the otolith-at-hatch. Otolith diameter-at-hatch was also significantly correlated with survival-at-age in fed and unfed larvae in the laboratory. For sardine larvae collected in the Bay of Biscay during the spring of 2008, otolith radius-at-hatch was also significantly related to viability. Larval mortality has frequently been related to adverse environmental conditions and intrinsic factors affecting feeding ability and vulnerability to predators. Our study offers evidence indicating that a significant portion of fish mortality occurs during the endogenous (yolk) and mixed (yolk /prey) feeding period in the absence of predators, revealing that marine fish with high fecundity, such as small pelagics, can spawn a relatively large amount of eggs resulting in small larvae with no chances to survive. Our findings help to better understand the mass mortalities occurring at early stages of marine fish.

Shear-wave elastography contributes to accurate tumour size estimation when assessing small breast cancers

International Nuclear Information System (INIS)

Mullen, R.; Thompson, J.M.; Moussa, O.; Vinnicombe, S.; Evans, A.

2014-01-01

Aim: To assess whether the size of peritumoural stiffness (PTS) on shear-wave elastography (SWE) for small primary breast cancers (≤15 mm) was associated with size discrepancies between grey-scale ultrasound (GSUS) and final histological size and whether the addition of PTS size to GSUS size might result in more accurate tumour size estimation when compared to final histological size. Materials and methods: A retrospective analysis of 86 consecutive patients between August 2011 and February 2013 who underwent breast-conserving surgery for tumours of size ≤15 mm at ultrasound was carried out. The size of PTS stiffness was compared to mean GSUS size, mean histological size, and the extent of size discrepancy between GSUS and histology. PTS size and GSUS were combined and compared to the final histological size. Results: PTS of >3 mm was associated with a larger mean final histological size (16 versus 11.3 mm, p < 0.001). PTS size of >3 mm was associated with a higher frequency of underestimation of final histological size by GSUS of >5 mm (63% versus 18%, p < 0.001). The combination of PTS and GSUS size led to accurate estimation of the final histological size (p = 0.03). The size of PTS was not associated with margin involvement (p = 0.27). Conclusion: PTS extending beyond 3 mm from the grey-scale abnormality is significantly associated with underestimation of tumour size of >5 mm for small invasive breast cancers. Taking into account the size of PTS also led to accurate estimation of the final histological size. Further studies are required to assess the relationship of the extent of SWE stiffness and margin status. - Highlights: • Peritumoural stiffness of greater than 3 mm was associated with larger tumour size. • Underestimation of tumour size by ultrasound was associated with peri-tumoural stiffness size. • Combining peri-tumoural stiffness size to ultrasound produced accurate tumour size estimation

Penetration of small and medium sized food companies on foreign markets

Directory of Open Access Journals (Sweden)

Ladislav Mura

2010-01-01

Full Text Available In the world the interconnection of national economies and internationalization of economic processes occur. In turbulent changing business environment only those companies that understand the current trends in global economy may survive, develop and prosper. Therefore, the issue of internationalization for most companies becomes to be more important and the process of in­ter­na­tio­na­li­za­tion is the way how to stand this increasingly competitive environment. In presented contribution, the attention is paid to issues of internationalization of Slovak food industry enterprises such as their way of business internationalization, percentage share of foreign - trading activities on overall business activity, company evaluation of business internationalization or barriers of foreign markets pe­ne­tra­tion that researched companies have to deal with. Small and medium-sized enterprises (SMEs are the engine of the Slovak economy, generator of development, innovation, growth and they employ more than 60% of employees. Almost all businesses operating in agri-food complex have character of small and medium enterprises. The results of carried research have shown that small and medium-sized companies are considered to be successful in operation on foreign markets in surrounding European countries.

Modeling, design and experimental validation of a small-sized magnetic gear

NARCIS (Netherlands)

Zanis, R.; Borisavljevic, A.; Jansen, J.W.; Lomonova, E.A.

2013-01-01

A magnetostatic analytical model is created to analyze and design a small-sized magnetic gear for a robotic application. Through a parameter variation study, it is found that the inner rotor magnet height is highly influential to the torque, and based on which, the design is performed. Several

Requirement analysis to promote small-sized E-waste collection from consumers.

Science.gov (United States)

Mishima, Kuniko; Nishimura, Hidekazu

2016-02-01

The collection and recycling of small-sized waste electrical and electronic equipment is an emerging problem, since these products contain certain amounts of critical metals and rare earths. Even if the amount is not large, having a few supply routes for such recycled resources could be a good strategy to be competitive in a world of finite resources. The small-sized e-waste sometimes contains personal information, therefore, consumers are often reluctant to put them into recycling bins. In order to promote the recycling of E-waste, collection of used products from the consumer becomes important. Effective methods involving incentives for consumers might be necessary. Without such methods, it will be difficult to achieve the critical amounts necessary for an efficient recycling system. This article focused on used mobile phones among information appliances as the first case study, since it contains relatively large amounts of valuable metals compared with other small-sized waste electrical and electronic equipment and there are a large number of products existing in the market. The article carried out surveys to determine what kind of recycled material collection services are preferred by consumers. The results clarify that incentive or reward money alone is not a driving force for recycling behaviour. The article discusses the types of effective services required to promote recycling behaviour. The article concludes that securing information, transferring data and providing proper information about resources and environment can be an effective tool to encourage a recycling behaviour strategy to promote recycling, plus the potential discount service on purchasing new products associated with the return of recycled mobile phones. © The Author(s) 2015.

Exact association test for small size sequencing data.

Science.gov (United States)

Lee, Joowon; Lee, Seungyeoun; Jang, Jin-Young; Park, Taesung

2018-04-20

Recent statistical methods for next generation sequencing (NGS) data have been successfully applied to identifying rare genetic variants associated with certain diseases. However, most commonly used methods (e.g., burden tests and variance-component tests) rely on large sample sizes. Notwithstanding, due to its-still high cost, NGS data is generally restricted to small sample sizes, that cannot be analyzed by most existing methods. In this work, we propose a new exact association test for sequencing data that does not require a large sample approximation, which is applicable to both common and rare variants. Our method, based on the Generalized Cochran-Mantel-Haenszel (GCMH) statistic, was applied to NGS datasets from intraductal papillary mucinous neoplasm (IPMN) patients. IPMN is a unique pancreatic cancer subtype that can turn into an invasive and hard-to-treat metastatic disease. Application of our method to IPMN data successfully identified susceptible genes associated with progression of IPMN to pancreatic cancer. Our method is expected to identify disease-associated genetic variants more successfully, and corresponding signal pathways, improving our understanding of specific disease's etiology and prognosis.

Experimental investigation of a small-sized betatron with superposed magnetization

International Nuclear Information System (INIS)

Kas'yanov, V.A.; Rychkov, M.V.; Filimonov, A.A.; Furman, Eh.G.; Chakhlov, V.L.; Chertov, A.S.; Shtejn, M.M.

2001-01-01

The aim of the paper is to study possibilities of small-sized betatrons (SSB) with direct current superposed magnetization (DSM). It is shown that DSM permits to decrease the SSB weight and cost of the electromagnet and capacitor storage and to shape the prolonged beam dump. It is noted that the DSM realization has the most expediency in SSB operating in a short-time mode [ru

Branding and outcomes in small and medium-sized enterprises (SMEs)

DEFF Research Database (Denmark)

Odoom, Raphael; Narteh, Bedman; Rand, John

2017-01-01

The study investigates the relationships of enterprise resources and branding capabilities with branding efforts and branding benefits. It examines the differential effect of physical resources and branding capabilities on enterprises’ branding efforts and outcomes. Empirical data for the study...... were drawn from 304 small and medium-sized enterprises (SMEs) in Ghana. The hypothesized relationships were analyzed using Structural Equation Modeling. The study found that resources and capabilities possessions might not be enough to produce the optimum branding benefits for enterprises. A better...... result, however, emerges when these resources and capabilities are integrated with well-coordinated branding efforts of the enterprises. The study offers several implications for managers of small businesses based on the findings of the study....

Small genomes and large seeds: chromosome numbers, genome size and seed mass in diploid Aesculus species (Sapindaceae).

Science.gov (United States)

Krahulcová, Anna; Trávnícek, Pavel; Krahulec, František; Rejmánek, Marcel

2017-04-01

Aesculus L. (horse chestnut, buckeye) is a genus of 12-19 extant woody species native to the temperate Northern Hemisphere. This genus is known for unusually large seeds among angiosperms. While chromosome counts are available for many Aesculus species, only one has had its genome size measured. The aim of this study is to provide more genome size data and analyse the relationship between genome size and seed mass in this genus. Chromosome numbers in root tip cuttings were confirmed for four species and reported for the first time for three additional species. Flow cytometric measurements of 2C nuclear DNA values were conducted on eight species, and mean seed mass values were estimated for the same taxa. The same chromosome number, 2 n = 40, was determined in all investigated taxa. Original measurements of 2C values for seven Aesculus species (eight taxa), added to just one reliable datum for A. hippocastanum , confirmed the notion that the genome size in this genus with relatively large seeds is surprisingly low, ranging from 0·955 pg 2C -1 in A. parviflora to 1·275 pg 2C -1 in A. glabra var. glabra. The chromosome number of 2 n = 40 seems to be conclusively the universal 2 n number for non-hybrid species in this genus. Aesculus genome sizes are relatively small, not only within its own family, Sapindaceae, but also within woody angiosperms. The genome sizes seem to be distinct and non-overlapping among the four major Aesculus clades. These results provide an extra support for the most recent reconstruction of Aesculus phylogeny. The correlation between the 2C values and seed masses in examined Aesculus species is slightly negative and not significant. However, when the four major clades are treated separately, there is consistent positive association between larger genome size and larger seed mass within individual lineages. © The Author 2017. Published by Oxford University Press on behalf of the Annals of Botany Company. All rights reserved. For

Fracture toughness of Charpy-size compound specimens and its application in engineering

International Nuclear Information System (INIS)

Zhang, X.P.; Shi, Y.W.

1994-01-01

The use of a pre-cracked Charpy-size specimen with a side-groove to evaluate the fracture toughness of materials has been researched and considered. This method not only satisfies the demand for small-size specimens in surveillance tests of fracture toughness but also avoids using complicated physical methods to monitor the initial conditions of crack propagation. For most materials this method has solved the problem in which the small-size specimen did not satisfy the valid conditions of a fracture toughness measurement. In order to obtain more information from neutron-irradiated sample specimens and raise the reliability of fracture toughness surveillance tests, it has been considered more important to repeatedly exploit the broken Charpy-size specimen tested in the surveillance test, and to make it renewable. In this work, on the renewing design and utilization of Charpy-size specimens, nine data on fracture toughness can be obtained from one pre-cracked side-grooved Charpy-size specimen, while at present usually only one to three data on fracture toughness can be obtained from one Charpy-size specimen. Thus, it is found that the new method would improve the reliability of fracture toughness surveillance testing and evaluation. In addition, some factors that affect the optimum design of pre-cracked deep side-groove Charpy-size compound specimens have also been discussed. (author)

Meaningfulness for creation of growth in Small- and Medium-sized enterprises

DEFF Research Database (Denmark)

Brink, Tove; Neville, Mette

2016-01-01

The research in this paper reveals how meaningfulness of growth can be created in Small- and Medium-sized Enterprises (SMEs). The research is conducted in a four-year period with 24 SMEs participating from different industry branches. The research is now in the late part of the 3rd. year starting...

Modern methods of evaluation existing suppliers and suppliers selected by customer for small and medium-sized companies

Directory of Open Access Journals (Sweden)

Marie Jurová

2010-01-01

Full Text Available On existing conditions on global market (almost identical quality, almost identical purchasing values companies have to definite the total rating of importance of evaluative criteria. In post-crisis period the problem of suppliers’ evaluation is one of the biggest, because companies had to use all resources and all possibilities to develop their own business. Many authors wrote about collaborative planning and warehousing as one of possibilities to optimization work inside supply chain. For this paper define small and medium-sized enterprises (SME as enterprises with the size of maximum 250 em­ployers. In literature was read we couldn’t find information about own system of suppliers evaluation for small and medium-sized enterprises. SME can have some different types of business and in this case need the universal system of eva­lua­tion. The research of this paper is oriented on small and medium-sized enterprises with different types of business. The new theoretical universal method of calculation for evaluation existing suppliers for small and medium-sized enterprises will present in this paper. This theoretical method is based on average values. This method includes traditional evaluative criteria (quality, delivery time and other (mobility of supplier, possibilities of new level of partnership. This method of evaluation can not be used for continual manufacture. New method can improve the total evaluation of supplier in small and medium-sized enterprises.

A deployable mechanism concept for the collection of small-to-medium-size space debris

Science.gov (United States)

St-Onge, David; Sharf, Inna; Sagnières, Luc; Gosselin, Clément

2018-03-01

Current efforts in active debris removal strategies and mission planning focus on removing the largest, most massive debris. It can be argued, however, that small untrackable debris, specifically those smaller than 5 cm in size, also pose a serious threat. In this work, we propose and analyze a mission to sweep the most crowded Low Earth Orbit with a large cupola device to remove small-to-medium-size debris. The cupola consists of a deployable mechanism expanding more than 25 times its storage size to extend a membrane covering its surface. The membrane is sufficiently stiff to capture most small debris and to slow down the medium-size objects, thus accelerating their fall. An overview of the design of a belt-driven rigid-link mechanism proposed to support the collecting cupola surface is presented, based on our previous work. Because of its large size, the cupola will be subject to significant aerodynamic drag; thus, orbit maintenance analysis is carried out using the DTM-2013 atmospheric density model and it predicts feasible requirements. While in operation, the device will also be subject to numerous hyper-velocity impacts which may significantly perturb its orientation from the desired attitude for debris collection. Thus, another important feature of the proposed debris removal device is a distributed array of flywheels mounted on the cupola for reorienting and stabilizing its attitude during the mission. Analysis using a stochastic modeling framework for hyper-velocity impacts demonstrates that three-axes attitude stabilization is achievable with the flywheels array. MASTER-2009 software is employed to provide relevant data for all debris related estimates, including the debris fluxes for the baseline mission design and for assessment of its expected performance. Space debris removal is a high priority for ensuring sustainability of space and continual launch and operation of man-made space assets. This manuscript presents the first analysis of a small

Incremental change in cross sectional area in small endotracheal tubes: A call for more size options.

Science.gov (United States)

Mortelliti, Caroline L; Mortelliti, Anthony J

2016-08-01

To elucidate the relatively large incremental percent change (IPC) in cross sectional area (CSA) in currently available small endotracheal tubes (ETTs), and to make recommendation for lesser incremental change in CSA in these smaller ETTs, in order to minimize iatrogenic airway injury. The CSAs of a commercially available line of ETTs were calculated, and the IPC of the CSA between consecutive size ETTs was calculated and graphed. The average IPC in CSA with large ETTs was applied to calculate identical IPC in the CSA for a theoretical, smaller ETT series, and the dimensions of a new theoretical series of proposed small ETTs were defined. The IPC of CSA in the larger (5.0-8.0 mm inner diameter (ID)) ETTs was 17.07%, and the IPC of CSA in the smaller ETTs (2.0-4.0 mm ID) is remarkably larger (38.08%). Applying the relatively smaller IPC of CSA from larger ETTs to a theoretical sequence of small ETTs, starting with the 2.5 mm ID ETT, suggests that intermediate sizes of small ETTs (ID 2.745 mm, 3.254 mm, and 3.859 mm) should exist. We recommend manufacturers produce additional small ETT size options at the intuitive intermediate sizes of 2.75 mm, 3.25 mm, and 3.75 mm ID in order to improve airway management for infants and small children. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Regional statistical and economic analysis of small and medium-sized businesses development in Zhytomyr region

Directory of Open Access Journals (Sweden)

S.I. Pavlova

2017-08-01

Full Text Available Small and medium-sized businesses play an important role in the development of the regional economic system in particular and in solving a number of the following local problems: developing competition, developing the market for goods and services, providing jobs for the able-bodied population, raising living standards and improving the social environment in society. The purpose of this paper is to analyze the state and development of small and medium-sized businesses in the Zhytomyr region, to analyze its contribution to the economic development of the region, and to identify the main problems existing in the region. According to the indicators of state statistics, the author presents the general characteristics of enterprises in the Zhytomyr region from 2012 to 2016 in the context of indicators of the number of enterprises, the number of employed workers and the volume of the products sold, highlighting the activities of small enterprises and assessing their share in general levels. In addition, the paper provides the description of the activities of individual entrepreneurs. The structural comparison for the above-listed indicators of the distribution of influence on the economic system of the Zhytomyr region in terms of enterprises by size is presented. In terms of quantity 93,5 % are small enterprises that provide 31,4 % of the total number of employees with work and make up 23,1 % of the total volume of sales. Average enterprises in these indicators have 6,4 %, 62,0 % and 54,8 % respectively. The statistical and economic analysis of the structure of small enterprises by types of economic activity, by indicators of the number of registered enterprises, and by the volumes of sold products is carried out. The uniformity of the distribution is estimated using the index of the concentration coefficient. The indicators of revenues to budgets of different levels from small and medium-sized businesses are set. The paper presents and summarizes the

Use of sales and operations planning in small and medium-sized enterprises

Directory of Open Access Journals (Sweden)

Michał Adamczak

2013-03-01

Full Text Available Background: Increasing competitiveness in the market, customer expectations related to the shortening of the deadlines and the reduction of prices of products and services force companies to improve the efficiency of internal processes. The integration of planning process is one of possible ways to achieve this aim. The integration of planning processes by the use of SOP model (Sales and Operations Planning is a method to implement this idea. The study allowed to identify ways to implement the process of sales and operations planning in small and medium-sized enterprises. Material and methods: The study was conducted in companies from different industries. The research method was in-depth interviews conducted with managers of companies or persons occupying management positions in the organizational process of implementing sales and operations planning. Results: During the survey, 10 companies were asked about the use of sales and operations planning, its elements and organizational aspects of its development, by the company. Conclusions: The use of sales and operations plan is closely dependent on the size of the company and its localization in the supply chain. Small enterprises are not interested in the integration of the planning process due to the small scale of operations and the centralization of decision-making process. Medium-sized enterprises, due to the increased complexity of the processes of planning, see the benefits of their integration in the SOP model.

Delivery of workshops on mobility monitoring in small to medium-sized communities.

Science.gov (United States)

2009-11-01

This report summarizes the delivery and outcome of a series of workshops conducted in 13 cities across the : state on performing mobility monitoring in small to medium-sized communities. The workshops served as : implementation for research project 0...

Conceptual design of small-sized HTGR system (3). Core thermal and hydraulic design

International Nuclear Information System (INIS)

Inaba, Yoshitomo; Sato, Hiroyuki; Goto, Minoru; Ohashi, Hirofumi; Tachibana, Yukio

2012-06-01

The Japan Atomic Energy Agency has started the conceptual designs of small-sized High Temperature Gas-cooled Reactor (HTGR) systems, aiming for the 2030s deployment into developing countries. The small-sized HTGR systems can provide power generation by steam turbine, high temperature steam for industry process and/or low temperature steam for district heating. As one of the conceptual designs in the first stage, the core thermal and hydraulic design of the power generation and steam supply small-sized HTGR system with a thermal power of 50 MW (HTR50S), which was a reference reactor system positioned as a first commercial or demonstration reactor system, was carried out. HTR50S in the first stage has the same coated particle fuel as HTTR. The purpose of the design is to make sure that the maximum fuel temperature in normal operation doesn't exceed the design target. Following the design, safety analysis assuming a depressurization accident was carried out. The fuel temperature in the normal operation and the fuel and reactor pressure vessel temperatures in the depressurization accident were evaluated. As a result, it was cleared that the thermal integrity of the fuel and the reactor coolant pressure boundary is not damaged. (author)

Position paper: Management of men complaining of a small penis despite an actually normal size.

Science.gov (United States)

Ghanem, Hussein; Glina, Sidney; Assalian, Pierre; Buvat, Jacques

2013-01-01

With the worldwide increase in penile augmentation procedures and claims of devices designed to elongate the penis, it becomes crucial to study the scientific basis of such procedures or devices, as well as the management of a complaint of a small penis in men with a normal penile size. The aim of this work is to study the scientific basis of opting to penile augmentation procedures and to develop guidelines based on the best available evidence for the management of men complaining of a small penis despite an actually normal size. We reviewed the literature and evaluated the evidence about what the normal penile size is, what patients complaining of a small penis usually suffer from, benefits vs. complications of surgery, penile stretching or traction devices, and outcome with patient education and counseling. Repeated presentation and detailed discussions within the Standard Committee of the International Society for Sexual Medicine were performed. Recommendations are based on the evaluation of evidence-based medical literature, widespread standards committee discussion, public presentation, and debate. We propose a practical approach for evaluating and counseling patients complaining of a small-sized penis. Based on the current status of science, penile lengthening procedure surgery is still considered experimental and should only be limited to special circumstances within research or university institutions with supervising ethics committees. © 2012 International Society for Sexual Medicine.

Determining the optimal size of small molecule mixtures for high throughput NMR screening

International Nuclear Information System (INIS)

Mercier, Kelly A.; Powers, Robert

2005-01-01

High-throughput screening (HTS) using NMR spectroscopy has become a common component of the drug discovery effort and is widely used throughout the pharmaceutical industry. NMR provides additional information about the nature of small molecule-protein interactions compared to traditional HTS methods. In order to achieve comparable efficiency, small molecules are often screened as mixtures in NMR-based assays. Nevertheless, an analysis of the efficiency of mixtures and a corresponding determination of the optimum mixture size (OMS) that minimizes the amount of material and instrumentation time required for an NMR screen has been lacking. A model for calculating OMS based on the application of the hypergeometric distribution function to determine the probability of a 'hit' for various mixture sizes and hit rates is presented. An alternative method for the deconvolution of large screening mixtures is also discussed. These methods have been applied in a high-throughput NMR screening assay using a small, directed library

13 CFR 121.412 - What are the size procedures for partial small business set-asides?

Science.gov (United States)

2010-01-01

... Requirements for Government Procurement § 121.412 What are the size procedures for partial small business set... portion of a procurement, and is not required to qualify as a small business for the unrestricted portion. ...

Mammographic casting-type calcification associated with small screen-detected invasive breast cancers: is this a reliable prognostic indicator?

International Nuclear Information System (INIS)

Peacock, C.; Given-Wilson, R.M.; Duffy, S.W.

2004-01-01

AIM: The aim of the present study was to establish whether mammographic casting-type calcification associated with small screen-detected invasive breast cancers is a reliable prognostic indicator. METHODS AND MATERIALS: We retrospectively identified 50 consecutive women diagnosed with an invasive cancer less than 15 mm who showed associated casting calcification on their screening mammograms. Controls were identified that showed no microcalcification and were matched for tumour size, histological type and lymph node status. A minimum of 5 years follow-up was obtained, noting recurrence and outcome. Conditional and unconditional logistic regression, depending on the outcome variable, were used to analyse the data, taking the matched design into account in both cases. Where small numbers prohibited the use of logistic regression, Fisher's exact test was used. RESULTS: Five deaths from breast cancer occurred out of the 50 cases, of which three were lymph node positive, two were lymph node negative and none were grade 3. None of the 78 control cases died from breast cancer. The difference in breast cancer death rates was significant by Fisher's exact test (p=0.02). Risk of recurrence was also significantly increased in the casting cases (OR=3.55, 95% CI 1.02-12.33, p=0.046). CONCLUSION: Although the overall outcome for small screen-detected breast cancers is good, our study suggests that casting calcification is a poorer prognostic factor. The advantage of a mammographic feature as an independent prognostic indicator lies in early identification of high-risk patients, allowing optimization of management

Guide to Cybersecurity, Resilience, and Reliability for Small and Under-Resourced Utilities

Energy Technology Data Exchange (ETDEWEB)

Ingram, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States); Martin, Maurice [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-01-01

Small electricity utilities -- those with less than 100 employees or 50,000 meters -- provide essential services to large parts of the United States while facing a number of challenges unique to their mission. For instance, they often serve areas that are sparsely populated, meaning that their per-customer cost to provide service is higher. At the same time, they often serve customers that have moderate or fixed incomes, meaning that they are under strong pressure to keep costs down. This pressure puts them on a strict budget and creates a need for innovative solutions to common problems. Further, their service areas may include extreme climates, making severe weather events more frequent and their aftermaths more expensive to address. This guide considers challenges that small utilities face while ensuring the reliability, resilience, and cybersecurity of their electric service; approaches to address those challenges using existing guidance documents; ways that the federal government could provide support in these areas.

Development of a small-sized generator of ozonated water using an electro-conductive diamond electrode.

Science.gov (United States)

Sekido, Kota; Kitaori, Noriyuki

2008-12-01

A small-sized generator of ozonated water was developed using an electro-conductive diamond. We studied the optimum conditions for producing ozonated water. As a result, we developed a small-sized generator of ozonated water driven by a dry-cell for use in the average household. This generator was easily able to produce ozonated water with an ozone concentration (over 4 mg/L) sufficient for disinfection. In addition, we verified the high disinfecting performance of the water produced in an actual hospital.

The development of internet based ship design support system for small and medium sized shipyards

Science.gov (United States)

Shin, Sung-Chul; Lee, Soon-Sup; Kang, Dong-Hoon; Lee, Kyung-Ho

2012-03-01

In this paper, a prototype of ship basic planning system is implemented for the small and medium sized shipyards based on the internet technology and concurrent engineering concept. The system is designed from the user requirements. Consequently, standardized development environment and tools are selected. These tools are used for the system development to define and evaluate core application technologies. The system will contribute to increasing competitiveness of small and medium sized shipyards in the 21st century industrial en-vironment.

SMGE: strategic challenges and performance measurement in a small-sized company (case)

NARCIS (Netherlands)

MBA R. Vieveen; PhD B. Pesalj

2015-01-01

Case portrays the Superior Manufacturing Group Europe (SMGE), Barendrecht (Netherlands), a small-sized company doing business in the matting industry; facing challenges of how to sustain and improve its performance, by balancing between entrepreneurial initiative, and a need for strategic planning

BurnCase 3D software validation study: Burn size measurement accuracy and inter-rater reliability.

Science.gov (United States)

Parvizi, Daryousch; Giretzlehner, Michael; Wurzer, Paul; Klein, Limor Dinur; Shoham, Yaron; Bohanon, Fredrick J; Haller, Herbert L; Tuca, Alexandru; Branski, Ludwik K; Lumenta, David B; Herndon, David N; Kamolz, Lars-P

2016-03-01

The aim of this study was to compare the accuracy of burn size estimation using the computer-assisted software BurnCase 3D (RISC Software GmbH, Hagenberg, Austria) with that using a 2D scan, considered to be the actual burn size. Thirty artificial burn areas were pre planned and prepared on three mannequins (one child, one female, and one male). Five trained physicians (raters) were asked to assess the size of all wound areas using BurnCase 3D software. The results were then compared with the real wound areas, as determined by 2D planimetry imaging. To examine inter-rater reliability, we performed an intraclass correlation analysis with a 95% confidence interval. The mean wound area estimations of the five raters using BurnCase 3D were in total 20.7±0.9% for the child, 27.2±1.5% for the female and 16.5±0.1% for the male mannequin. Our analysis showed relative overestimations of 0.4%, 2.8% and 1.5% for the child, female and male mannequins respectively, compared to the 2D scan. The intraclass correlation between the single raters for mean percentage of the artificial burn areas was 98.6%. There was also a high intraclass correlation between the single raters and the 2D Scan visible. BurnCase 3D is a valid and reliable tool for the determination of total body surface area burned in standard models. Further clinical studies including different pediatric and overweight adult mannequins are warranted. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

US market potential for small and medium-sized nuclear reactors

International Nuclear Information System (INIS)

Hardie, R.W.; Jackson, S.V.

1988-01-01

This paper presents the results of on-site interviews with representatives of 23 investor-owned utilities and 3 publicly-owned utilities. The purpose of the interviews was to obtain information on utilities' attitudes towards small and medium-sized power plants and towards building new nuclear plants in general. Most of the utilities interviewed preferred power plants smaller than the ones currently being offered, as long as the smaller plants did not incur a major economic penalty. However, according to the utilities interviewed, without changes in the current environment it is unlikely that there will be a significant market for new nuclear plants of any size. A trend in the utility industry towards generating companies appears to be a positive step. (orig.)

US market potential for small and medium-sized nuclear reactors

International Nuclear Information System (INIS)

Hardie, R.W.; Jackson, S.V.

1987-01-01

This paper presents the results of on-site interviews with representatives of 23 investor-owned utilities and 3 publicly-owned utilities. The purpose of the interviews was to obtain information on utilities' attitudes toward small and medium-sized power plants and towards building new nuclear plants in general. Most of the utilities interviewed preferred power plants smaller than the ones currently being offered, as long as the smaller plants did not incur a major economic penalty. However, according to the utilities interviewed, without changes in the current environment it is unlikely that there will be a significant market for new nuclear plants of any size. A trend in the utility industry towards generating companies appears to be a positive step. (author)

Greening Small and Medium-Sized Enterprises: Evaluating Environmental Policy in Vietnam

NARCIS (Netherlands)

Van Khoa, Le

2006-01-01

Small and Medium-sized Enterprises (SMEs) contribute considerably to the economic and social development of bothViet Namand Ho Chi Minh City (HCMC). But at the same time this sector causes severe environmental

[Application of health questionnaires for health management in small- and medium-sized enterprises].

Science.gov (United States)

Kishida, K; Saito, M; Hasegawa, T; Aoki, S; Suzuki, S

1986-01-01

Two kinds of health questionnaires, the Todai Health Index (THI) and Cumulative Fatigue Index (CFI), were applied as a screening device for health management of workers belonging to small-medium sized enterprises. A total of 495 workers composed of 452 male workers of a glass-bottle manufacturing factory and 43 male workers of a soft-drink bottling factory were the subjects of the present study. It was found that the two kinds of health questionnaires were different from each other and have their own characteristics. Twelve scales of THI were grouped into two, the first consisting of ten scales (SUSY, RESP, EYSK, MOUT, DIGE, IMPU, MENT, DEPR, NERV, and LIFE) and the second consisting of two scales (AGGR and LISC). Nine categories of CFI were grouped into one by using principal factor analysis. It was confirmed that the twelve scale scores of THI obtained at small-medium sized factories differed from those scale scores of a reference group investigated at a large-sized enterprise. It is on the basis of the scales of aggressiveness and lies and also of the scale of mental unstability which characterizes workers, locality, job (clerical or field work), and size of industry (large or small sized) that the difference could be evaluated. Urban life characterized by a life style of staying up late at night and waking up late in the morning has been reflected on the scale of life irregularity. Irregularity of life induced by transformation of working schedule, such as two or three shifts of work and overtime, was also reflected on this scale. Two scales of THI test, i.e., many subjective symptoms and digestive organ complaints, seemed to be the representative scales indicating a close relation between work load and health level. The discriminant score for diagnosis of psychosomatic diseases is considered to be one of the most useful assessments of the individual's health condition. As mentioned above, THI is recommended as a convenient assessment method for health

Limits to the reliability of size-based fishing status estimation for data-poor stocks

DEFF Research Database (Denmark)

Kokkalis, Alexandros; Thygesen, Uffe Høgsbro; Nielsen, Anders

2015-01-01

For stocks which are considered “data-poor” no knowledge exist about growth, mortality or recruitment. The only available information is from catches. Here we examine the ability to assess the level of exploitation of a data-poor stock based only on information of the size of individuals in catches....... The model is a formulation of the classic Beverton–Holt theory in terms of size where stock parameters describing growth, natural mortality, recruitment, etc. are determined from life-history invariants. A simulation study was used to compare the reliability of assessments performed under different...... to a considerable improvement in the assessment. Overall, the simulation study demonstrates that it may be possible to classify a data-poor stock as undergoing over- or under-fishing, while the exact status, i.e., how much the fishing mortality is above or below Fmsy, can only be assessed with a substantial...

Consultant-Client Relationship and Knowledge Transfer in Small- and Medium-Sized Enterprises Change Processes.

Science.gov (United States)

Martinez, Luis F; Ferreira, Aristides I; Can, Amina B

2016-04-01

Based on Szulanski's knowledge transfer model, this study examined how the communicational, motivational, and sharing of understanding variables influenced knowledge transfer and change processes in small- and medium-sized enterprises, particularly under projects developed by funded programs. The sample comprised 144 entrepreneurs, mostly male (65.3%) and mostly ages 35 to 45 years (40.3%), who filled an online questionnaire measuring the variables of "sharing of understanding," "motivation," "communication encoding competencies," "source credibility," "knowledge transfer," and "organizational change." Data were collected between 2011 and 2012 and measured the relationship between clients and consultants working in a Portuguese small- and medium-sized enterprise-oriented action learning program. To test the hypotheses, structural equation modeling was conducted to identify the antecedents of sharing of understanding, motivational, and communicational variables, which were positively correlated with the knowledge transfer between consultants and clients. This transfer was also positively correlated with organizational change. Overall, the study provides important considerations for practitioners and academicians and establishes new avenues for future studies concerning the issues of consultant-client relationship and the efficacy of Government-funded programs designed to improve performance of small- and medium-sized enterprises. © The Author(s) 2016.

77 FR 55737 - Small Business Size Standards: Finance and Insurance and Management of Companies and Enterprises

Science.gov (United States)

2012-09-11

... 3245-AG45 Small Business Size Standards: Finance and Insurance and Management of Companies and Enterprises AGENCY: U.S. Small Business Administration. ACTION: Proposed rule. SUMMARY: The U.S. Small... NAICS Sector 55, Management of Companies and Enterprises. In addition, SBA proposes to change the...

Addressing small sample size bias in multiple-biomarker trials: Inclusion of biomarker-negative patients and Firth correction.

Science.gov (United States)

Habermehl, Christina; Benner, Axel; Kopp-Schneider, Annette

2018-03-01

In recent years, numerous approaches for biomarker-based clinical trials have been developed. One of these developments are multiple-biomarker trials, which aim to investigate multiple biomarkers simultaneously in independent subtrials. For low-prevalence biomarkers, small sample sizes within the subtrials have to be expected, as well as many biomarker-negative patients at the screening stage. The small sample sizes may make it unfeasible to analyze the subtrials individually. This imposes the need to develop new approaches for the analysis of such trials. With an expected large group of biomarker-negative patients, it seems reasonable to explore options to benefit from including them in such trials. We consider advantages and disadvantages of the inclusion of biomarker-negative patients in a multiple-biomarker trial with a survival endpoint. We discuss design options that include biomarker-negative patients in the study and address the issue of small sample size bias in such trials. We carry out a simulation study for a design where biomarker-negative patients are kept in the study and are treated with standard of care. We compare three different analysis approaches based on the Cox model to examine if the inclusion of biomarker-negative patients can provide a benefit with respect to bias and variance of the treatment effect estimates. We apply the Firth correction to reduce the small sample size bias. The results of the simulation study suggest that for small sample situations, the Firth correction should be applied to adjust for the small sample size bias. Additional to the Firth penalty, the inclusion of biomarker-negative patients in the analysis can lead to further but small improvements in bias and standard deviation of the estimates. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Using small area estimation and Lidar-derived variables for multivariate prediction of forest attributes

Science.gov (United States)

F. Mauro; Vicente Monleon; H. Temesgen

2015-01-01

Small area estimation (SAE) techniques have been successfully applied in forest inventories to provide reliable estimates for domains where the sample size is small (i.e. small areas). Previous studies have explored the use of either Area Level or Unit Level Empirical Best Linear Unbiased Predictors (EBLUPs) in a univariate framework, modeling each variable of interest...

Financial Management Challenges In Small And Medium-Sized Enterprises: A Strategic Management Approach

Directory of Open Access Journals (Sweden)

Hande Karadag

2015-02-01

Full Text Available Abstract :Due to their significant role in creation of new jobs, rise in GDP, entrepreneurship and innovation, small and medium-sized enterprises (SMEs are recognized as the the drivers of socio-economic growth, both in developed and developing economies. In Turkey, 99.9 % of all enterprises fall into SME category. Therefore, the significance of SMEs for Turkish economy and society is much higher in Turkey, compared to other emerging and developed countries. Small and medium-sized companies are faced with a number of challenges whereas the problems arising from “poor financial management” are reported as the major causes of business failures in SMEs. Strategic financial management (SFM which is a research area that has attracted the interest of researchers after 2010, is one of the key managerial areas of SMEs, due to its vital role on the survival, growth and performance of SMEs. The purpose of this paper is to analyze the central role of financial management and identify the financial management challenges and practices that influence the organizational performance in Turkish SMEs, from a strategic management perspective. Within the course of this paper, the importance and challenges of SMEs in Turkey are presented in the first section, while the literature on strategic and financial management in SMEs are reviewed in the second part. In the third section, the recent strategic financial management concept, the implications of strategic financial management practices for SMEs in Turkey and the relationships between strategic financial management practices and SME performance, are discussed. Small and medium sized enterprise finance in Turkey is a developing research area, therefore this paper aims to make a significant contribution to the existing literature by analyzing the major challenges at the conduct of financial management in Turkish SMEs and the influence of strategic financial management practices on the performances of small and

Electron Emitter for small-size Electrodynamic Space Tether using MEMS Technology

DEFF Research Database (Denmark)

Fleron, René A. W.; Blanke, Mogens

2004-01-01

Adjustment of the orbit of a spacecraft using the forces created by an electro-dynamic space-tether has been shown as a theoretic possibility in recent literature. Practical implementation is being pursued for larger scale missions where a hot filament device controls electron emission...... and the current flowing in the electrodynamic space tether. Applications to small spacecraft, or space debris in the 1–10 kg range, possess difficulties with electron emission technology, as low power emitting devices are needed. This paper addresses the system concepts of a small spacecraft electrodynamic tether...... system with focus on electron emitter design and manufacture using micro-electro-mechanical- system (MEMS) technology. The paper addresses the system concepts of a small size electrodynamic tether mission and shows a novel electron emitter for the 1-2 mA range where altitude can be effectively affected...

Accelerated reliability demonstration under competing failure modes

International Nuclear Information System (INIS)

Luo, Wei; Zhang, Chun-hua; Chen, Xun; Tan, Yuan-yuan

2015-01-01

The conventional reliability demonstration tests are difficult to apply to products with competing failure modes due to the complexity of the lifetime models. This paper develops a testing methodology based on the reliability target allocation for reliability demonstration under competing failure modes at accelerated conditions. The specified reliability at mission time and the risk caused by sampling of the reliability target for products are allocated for each failure mode. The risk caused by degradation measurement fitting of the target for a product involving performance degradation is equally allocated to each degradation failure mode. According to the allocated targets, the accelerated life reliability demonstration test (ALRDT) plans for the failure modes are designed. The accelerated degradation reliability demonstration test plans and the associated ALRDT plans for the degradation failure modes are also designed. Next, the test plan and the decision rules for the products are designed. Additionally, the effects of the discreteness of sample size and accepted number of failures for failure modes on the actual risks caused by sampling for the products are investigated. - Highlights: • Accelerated reliability demonstration under competing failure modes is studied. • The method is based on the reliability target allocation involving the risks. • The test plan for the products is based on the plans for all the failure modes. • Both failure mode and degradation failure modes are considered. • The error of actual risks caused by sampling for the products is small enough

Method of Quantifying Size of Retinal Hemorrhages in Eyes with Branch Retinal Vein Occlusion Using 14-Square Grid: Interrater and Intrarater Reliability

Directory of Open Access Journals (Sweden)

Yuko Takashima

2016-01-01

Full Text Available Purpose. To describe a method of quantifying the size of the retinal hemorrhages in branch retinal vein occlusion (BRVO and to determine the interrater and intrarater reliabilities of these measurements. Methods. Thirty-five fundus photographs from 35 consecutive eyes with BRVO were studied. The fundus images were analyzed with Power-Point® software, and a grid of 14 squares was laid over the fundus image. Raters were asked to judge the percentage of each of the 14 squares that was covered by the hemorrhages, and the average of the 14 squares was taken to be the relative size of the retinal hemorrhage. Results. Interrater reliability between three raters was higher when a grid with 14 squares was used (intraclass correlation coefficient (ICC, 0.96 than that when a box with no grid was used (ICC, 0.78. Intrarater reliability, which was calculated by the retinal hemorrhage area measured on two different days, was also higher (ICC, 0.97 than that with no grid (ICC, 0.86. Interrater reliability for five fundus pictures with poor image quality was also good when a grid with 14 squares was used (ICC, 0.88. Conclusions. Although our method is subjective, excellent interrater and intrarater reliabilities indicate that this method can be adapted for clinical use.

The role of small and medium size reactors in the future US nuclear market

International Nuclear Information System (INIS)

Twilley, R.C.

2002-01-01

This paper addresses the various aspects of siting and sizing new generating facilities in the USA. Environmental and licensing issues are discussed. The economic considerations and assumptions for new plants are presented. Also, the electric transmission and distribution system characteristics and constraints are described with the potential role for several small and medium size designs summarized. (authors)

Small Size and Low Cost UHF RFID Tag Antenna Mountable on Metallic Objects

Directory of Open Access Journals (Sweden)

Sergio López-Soriano

2015-01-01

Full Text Available Reducing tag size while maintaining good performance is one of the major challenges in radio-frequency identification applications (RFID, in particular when labeling metallic objects. In this contribution, a small size and low cost tag antenna for identifying metal objects in the European UHF band (865–868 MHz is presented. The antenna consists of a transmission line mounted on an inexpensive thin dielectric which is proximity-coupled to a short-ended patch mounted on FR4 substrate. The overall dimensions of the tag are 33.5 × 30 × 3.1 mm. Experimental results show that, for an EIRP of 3.2 W (European regulations, such a small and cheap tag attains read ranges of about 5 m when attached to a metallic object.

Estimation of Poverty in Small Areas

Directory of Open Access Journals (Sweden)

Agne Bikauskaite

2014-12-01

Full Text Available A qualitative techniques of poverty estimation is needed to better implement, monitor and determine national areas where support is most required. The problem of small area estimation (SAE is the production of reliable estimates in areas with small samples. The precision of estimates in strata deteriorates (i.e. the precision decreases when the standard deviation increases, if the sample size is smaller. In these cases traditional direct estimators may be not precise and therefore pointless. Currently there are many indirect methods for SAE. The purpose of this paper is to analyze several diff erent types of techniques which produce small area estimates of poverty.

Gastro-oesophageal reflux in large-sized, deep-chested versus small-sized, barrel-chested dogs undergoing spinal surgery in sternal recumbency.

Science.gov (United States)

Anagnostou, Tilemahos L; Kazakos, George M; Savvas, Ioannis; Kostakis, Charalampos; Papadopoulou, Paraskevi

2017-01-01

The aim of this study was to investigate whether an increased frequency of gastro-oesophageal reflux (GOR) is more common in large-sized, deep-chested dogs undergoing spinal surgery in sternal recumbency than in small-sized, barrelchested dogs. Prospective, cohort study. Nineteen small-sized, barrel-chested dogs (group B) and 26 large-sized, deep-chested dogs (group D). All animals were premedicated with intramuscular (IM) acepromazine (0.05 mg kg -1 ) and pethidine (3 mg kg -1 ) IM. Anaesthesia was induced with intravenous sodium thiopental and maintained with halothane in oxygen. Lower oesophageal pH was monitored continuously after induction of anaesthesia. Gastro-oesophageal reflux was considered to have occurred whenever pH values > 7.5 or < 4 were recorded. If GOR was detected during anaesthesia, measures were taken to avoid aspiration of gastric contents into the lungs and to prevent the development of oesophagitis/oesophageal stricture. The frequency of GOR during anaesthesia was significantly higher in group D (6/26 dogs; 23.07%) than in group B (0/19 dogs; 0%) (p = 0.032). Signs indicative of aspiration pneumonia, oesophagitis or oesophageal stricture were not reported in any of the GOR cases. In large-sized, deep-chested dogs undergoing spinal surgery in sternal recumbency, it would seem prudent to consider measures aimed at preventing GOR and its potentially devastating consequences (oesophagitis/oesophageal stricture, aspiration pneumonia). Copyright © 2016 Association of Veterinary Anaesthetists and American College of Veterinary Anesthesia and Analgesia. Published by Elsevier Ltd. All rights reserved.

Role of Relationship Marketing in Small and Medium-Sized Entreprises

Directory of Open Access Journals (Sweden)

Ružica Butigan

2011-06-01

Full Text Available Along with marketing, small and medium enterprises (SMEs are commonly associated in literature with relationship marketing which results in marketing networks. This paper examines the specific characteristics that differentiate large companies from small and medium-sized enterprises, and the reasons that prevent SMEs from engaging in traditional marketing within the scope of marketing mix. The paper also shows that the key characteristic which distinguishes small from large companies is a prominent role of owner/managers. The owner/manager affects marketing of SMEs by creating his or her own personal networks with stakeholders in the environment, and considers it an important strategic focus and a factor that increases the performance of marketing decision-making. After a thorough review of secondary data sources this paper examines relationship marketing as a marketing framework for SMEs and, finally, proves that relationship marketing is more appropriate for SMEs than are traditional marketing concepts, that relationship marketing and network marketing create an important framework for SMEs and that there is a link between relationship marketing, personal networks and SMEs.

Advances in small zero-leak valves point to better nuclear power-plant reliability

Energy Technology Data Exchange (ETDEWEB)

Eacott, K B; Kin, J C; Hotta, Y [Dresser Japan, Ltd.

1978-04-01

In the selection of small valves less than two inches used for nuclear power plants, sufficient consideration must be given to the reliability to radioactive material, the easy operability, and the significant function, especially zero leak. These valves are classified into bellows and diaphragm seal types which must satisfy zero leak, 4000 cycles life test and good maintainability. Welded bellows, formed bellows, and metal diaphragms are actually used for these requirements. The construction of these types are shown. The requirements and principal specifications for these small valves are explained, and some examples are given. These zero leak valves are installed in reactor coolant loop system, borated water from B. A. system, pressurizer instrument system, containment spray system, high head system and off gas system for PWRS, and main steam line system, diesel generator cooling water system, re-circulation system, clean up water system, etc. for BWRS.

VOLTTRON™: Tech-to-Market Best-Practices Guide for Small- and Medium-Sized Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Haack, Jereme N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Katipamula, Srinivas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Nicholls, Andrew K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-07-11

VOLTTRON™ is an open-source distributed control and sensing platform developed by Pacific Northwest National Laboratory for the U.S. Department of Energy. It was developed to be used by the Office of Energy Efficiency and Renewable Energy to support transactive controls research and deployment activities. VOLTTRON is designed to be an overarching integration platform that could be used to bring together vendors, users, and developers and enable rapid application development and testing. The platform is designed to support modern control strategies, including the use of agent- and transaction-based controls. It also is designed to support the management of a wide range of applications, including heating, ventilation, and air-conditioning systems; electric vehicles; and distributed-energy and whole-building loads. This report was completed as part of the Building Technologies Office’s Technology-to-Market Initiative for VOLTTRON’s Market Validation and Business Case Development efforts. The report provides technology-to-market guidance and best practices related to VOLTTRON platform deployments and commercialization activities for use by entities serving small- and medium-sized commercial buildings. The report characterizes the platform ecosystem within the small- and medium-sized commercial building market and articulates the value proposition of VOLTTRON for three core participants in this ecosystem: 1) platform owners/adopters, 2) app developers, and 3) end-users. The report also identifies key market drivers and opportunities for open platform deployments in the small- and medium-sized commercial building market. Possible pathways to the market are described—laboratory testing to market adoption to commercialization. We also identify and address various technical and market barriers that could hinder deployment of VOLTTRON. Finally, we provide “best practice” tech-to-market guidance for building energy-related deployment efforts serving small- and

Engineering structure design and fabrication process of small sized China helium-cooled solid breeder test blanket module

International Nuclear Information System (INIS)

Wang Zeming; Chen Lu; Hu Gang

2014-01-01

Preliminary design and analysis for china helium-cooled solid breeder (CHHC-SB) test blanket module (TBM) have been carried out recently. As partial verification that the original size module was reasonable and the development process was feasible, fabrication work of a small sized module was to be carried out targetedly. In this paper, detailed design and structure analysis of small sized TBM was carried out based on preliminary design work, fabrication process and integrated assembly process was proposed, so a fabrication for the trial engineering of TBM was layed successfully. (authors)

Wind and solar data for sizing small wind turbine and photovoltaic power plants

Energy Technology Data Exchange (ETDEWEB)

Grainger, W [Northumbrian Energy Workshop Ltd., Hexham (GB)

1990-01-01

Small renewable energy power systems have to be more carefully sized and installed than fossil fuelled alternatives. Accurate assessment of the energy resource available at the site is the first step in system design. This paper describes the sort of data available and how they are processed. When small systems are involved there is little money available for detailed meteorological investigations. This has led our company to develop the techniques described. (author).

A Single IGF1 Allele Is a Major Determinant of Small Size in Dogs

OpenAIRE

Sutter, Nathan B.; Bustamante, Carlos D.; Chase, Kevin; Gray, Melissa M.; Zhao, Keyan; Zhu, Lan; Padhukasahasram, Badri; Karlins, Eric; Davis, Sean; Jones, Paul G.; Quignon, Pascale; Johnson, Gary S.; Parker, Heidi G.; Fretwell, Neale; Mosher, Dana S.

2007-01-01

The domestic dog exhibits greater diversity in body size than any other terrestrial vertebrate. We used a strategy that exploits the breed structure of dogs to investigate the genetic basis of size. First, through a genome-wide scan, we identified a major quantitative trait locus (QTL) on chromosome 15 influencing size variation within a single breed. Second, we examined genetic variation in the 15-megabase interval surrounding the QTL in small and giant breeds and found marked evidence for a...

Status and prospects for small and medium sized reactors

International Nuclear Information System (INIS)

Kupitz, J.; Arkhipov, V.; Brey, H.L.

2000-01-01

Member States have evinced interest in the continued development of small and medium sized reactors (SMRs) as an energy source for the future. Support for this programme was recently reaffirmed at the IAEA 1997 General Conference. Although the generation of electricity is the predominant focus of existing SMRs, there is increasing interest in using these plants for desalination, district heating and high temperature industrial process heat applications. Here is a review of SMR development within selected Member States, an overview of the IAEA's SMR programme and a discussion of selected SMR designs with emphasis on safety attributes. (author)

Prognostic Factors Affecting Rotator Cuff Healing After Arthroscopic Repair in Small to Medium-sized Tears.

Science.gov (United States)

Park, Ji Soon; Park, Hyung Jun; Kim, Sae Hoon; Oh, Joo Han

2015-10-01

Small and medium-sized rotator cuff tears usually have good clinical and anatomic outcomes. However, healing failure still occurs in some cases. To evaluate prognostic factors for rotator cuff healing in patients with only small to medium-sized rotator cuff tears. Case-control study; Level of evidence, 3. Data were prospectively collected from 339 patients with small to medium-sized rotator cuff tears who underwent arthroscopic repair by a single surgeon between March 2004 and August 2012 and who underwent magnetic resonance imaging or computed tomographic arthrography at least 1 year after surgery. The mean age of the patients was 59.8 years (range, 39-80 years), and the mean follow-up time was 20.8 months (range, 12-66 months). The functional evaluation included the visual analog scale (VAS) for pain, American Shoulder and Elbow Surgeons score, Constant-Murley score, and Simple Shoulder Test. Postoperative VAS for pain and functional scores improved significantly compared with preoperative values (P rotator cuff healing (P 2 cm in size (34.2%) compared with patients with a tear ≤2 cm (10.6%) (P rotator cuff tears, grade II fatty degeneration of the infraspinatus muscle according to the Goutallier classification could be a reference point for successful healing, and anatomic outcomes might be better if repair is performed before the patient is 69 years old and the tear size exceeds 2 cm. © 2015 The Author(s).

Understanding Informal Learning in Small- and Medium-Sized Enterprises in South Korea

Science.gov (United States)

Jeong, Shinhee; McLean, Gary N.; Park, Soyoun

2018-01-01

Purpose: This paper aims to explore informal learning experiences among employees working in South Korean small- and medium-sized enterprises (SMEs) with fewer than 100 employees. This study specifically seeks to understand the characteristics of informal learning in Korean SMEs and culturally sensitive contextual factors that shape informal…

Simultaneous analysis of small organic acids and humic acids using high performance size exclusion chromatography

NARCIS (Netherlands)

Qin, X.P.; Liu, F.; Wang, G.C.; Weng, L.P.

2012-01-01

An accurate and fast method for simultaneous determination of small organic acids and much larger humic acids was developed using high performance size exclusion chromatography. Two small organic acids, i.e. salicylic acid and 2,3-dihydroxybenzoic acid, and one purified humic acid material were used

A rule induction approach to improve Monte Carlo system reliability assessment

International Nuclear Information System (INIS)

Rocco S, Claudio M.

2003-01-01

A Decision Tree (DT) approach to build empirical models for use in Monte Carlo reliability evaluation is presented. The main idea is to develop an estimation algorithm, by training a model on a restricted data set, and replacing the Evaluation Function (EF) by a simpler calculation, which provides reasonably accurate model outputs. The proposed approach is illustrated with two systems of different size, represented by their equivalent networks. The robustness of the DT approach as an approximated method to replace the EF is also analysed. Excellent system reliability results are obtained by training a DT with a small amount of information

European Health Claims for Small and Medium-Sized Companies – Utopian Dream or Future Reality?

Directory of Open Access Journals (Sweden)

Sonja Brandenburger

2015-02-01

Full Text Available Background: In December 2007, the European Regulation (EC 1924/2006 on nutrition and health claims came into force. The European Union wanted to regulate the use of health claims on products. An online survey was carried out to evaluate the situation, particularly of small and medium-sized companies, dealing with the new regulation. Methods: The online survey on health claims was conducted with 16 enterprises. To underline the findings a SWOT (Strength, Weaknesses, Opportunities, Threats analysis was made of the nutrition and health claims regulation regarding small and medium-sized companies in the European food and drink market. Results: The findings of this study indicated that the European Union did a step in the right direction. Most companies defined the decent competition, the simplified trade within the inner-European market, and the consumer protection as positive aspects. The biggest threat is seen in false investment conditioned by the limited research and development budgets, especially of small and medium-sized enterprises, and the cost intensive scientific evaluation to reach an authorized health claim. Conclusions: Overall, there are several strengths and opportunities speaking for SMEs and health claims in the near future. The most promising ones are the publishing of the new European Union Register of Nutrition and Health Claims and the learning effects that will occur. The biggest threat is, and will remain to be, false investment and the possible loss of a lot of money. Nevertheless, health claims for small and medium-sized enterprises will inevitably be the future to keep the European food and drink market competitive.

A miniature small size 3 MeV deuteron linear accelerator

International Nuclear Information System (INIS)

Baranov, L.N.; Bryzgalov, G.A.; Verbovskij, V.V.; Kovpak, N.E.; Onoprienko, V.T.; Papkovich, V.G.; Khizhnyak, N.A.; Shulika, N.G.; Yashin, V.P.

1975-01-01

Basic characteristics are presented of the small-size linear deuteron accelerator for 3 MeV, the accelerating system of which operates at H-wave. It is shown that the usage of such accelerating systems makes it possible to reduce the resonator volume by more than 30 times, whereas the capacity of the evacuating devices as well as the total HF supply power are decreased. Owing to a relatively large wave length, particle injection energy may be reduced to 100-150 keV

Binomial outcomes in dataset with some clusters of size two: can the dependence of twins be accounted for? A simulation study comparing the reliability of statistical methods based on a dataset of preterm infants.

Science.gov (United States)

Sauzet, Odile; Peacock, Janet L

2017-07-20

The analysis of perinatal outcomes often involves datasets with some multiple births. These are datasets mostly formed of independent observations and a limited number of clusters of size two (twins) and maybe of size three or more. This non-independence needs to be accounted for in the statistical analysis. Using simulated data based on a dataset of preterm infants we have previously investigated the performance of several approaches to the analysis of continuous outcomes in the presence of some clusters of size two. Mixed models have been developed for binomial outcomes but very little is known about their reliability when only a limited number of small clusters are present. Using simulated data based on a dataset of preterm infants we investigated the performance of several approaches to the analysis of binomial outcomes in the presence of some clusters of size two. Logistic models, several methods of estimation for the logistic random intercept models and generalised estimating equations were compared. The presence of even a small percentage of twins means that a logistic regression model will underestimate all parameters but a logistic random intercept model fails to estimate the correlation between siblings if the percentage of twins is too small and will provide similar estimates to logistic regression. The method which seems to provide the best balance between estimation of the standard error and the parameter for any percentage of twins is the generalised estimating equations. This study has shown that the number of covariates or the level two variance do not necessarily affect the performance of the various methods used to analyse datasets containing twins but when the percentage of small clusters is too small, mixed models cannot capture the dependence between siblings.

Binomial outcomes in dataset with some clusters of size two: can the dependence of twins be accounted for? A simulation study comparing the reliability of statistical methods based on a dataset of preterm infants

Directory of Open Access Journals (Sweden)

Odile Sauzet

2017-07-01

Full Text Available Abstract Background The analysis of perinatal outcomes often involves datasets with some multiple births. These are datasets mostly formed of independent observations and a limited number of clusters of size two (twins and maybe of size three or more. This non-independence needs to be accounted for in the statistical analysis. Using simulated data based on a dataset of preterm infants we have previously investigated the performance of several approaches to the analysis of continuous outcomes in the presence of some clusters of size two. Mixed models have been developed for binomial outcomes but very little is known about their reliability when only a limited number of small clusters are present. Methods Using simulated data based on a dataset of preterm infants we investigated the performance of several approaches to the analysis of binomial outcomes in the presence of some clusters of size two. Logistic models, several methods of estimation for the logistic random intercept models and generalised estimating equations were compared. Results The presence of even a small percentage of twins means that a logistic regression model will underestimate all parameters but a logistic random intercept model fails to estimate the correlation between siblings if the percentage of twins is too small and will provide similar estimates to logistic regression. The method which seems to provide the best balance between estimation of the standard error and the parameter for any percentage of twins is the generalised estimating equations. Conclusions This study has shown that the number of covariates or the level two variance do not necessarily affect the performance of the various methods used to analyse datasets containing twins but when the percentage of small clusters is too small, mixed models cannot capture the dependence between siblings.

The role of independent intermediaries. The case of small and medium-sized exporters

DEFF Research Database (Denmark)

Madsen, Tage Koed; Moen, Øystein; Hammervold, Randi

2012-01-01

and participation rather than just discrete types of intermediary modes (agents, importers, dealers, etc.). Associations with performance as well as the role of product and distributor characteristics are analyzed. Empirical data based on a sample of product-market ventures in 227 small and medium-sized Norwegian...... export firms are analysed by a structural equation modelling approach. The article provides empirical evidence that managers keep control of decision making to an extent that may have a negative impact on export performance. The empirical study indicates that firms should participate more in task......The article examines how small and medium-sized exporters collaborate with intermediaries in foreign markets by studying the level of control, i.e. the delegation of decisions rights and task solution. It goes one step further than previous research, since it examines degrees of control...

The Suitability of Expert System Application in Czech Small and Medium‑Sized Enterprises

Directory of Open Access Journals (Sweden)

Ekaterina Khitilova

2017-01-01

Full Text Available Small and medium-sized enterprises play an important role in the economy of Czech Republic. Expert systems are one of the alternatives evaluated the effectiveness of the relationship between supplier and customer. Currently, measurement and increase in efficiency of supplier-customer relations is very topical subject. The requirements for tools the improvement supplier- customer relationship can be specified on the base the literature analysis. The article defines basic requirements for expert system. The presentation of expert system and its suitability in the surroundings of small and medium sized enterprises is the part of this article. The comparison of the expert system possibilities and the compiled requirements leads to suitability analysis of selected solution. Actual questions and the way of future work are derived from current results, presented in the paper. The article defined the directions of development this expert system.

Uncertainty evaluation of reliability of shutdown system of a medium size fast breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Zeliang, Chireuding; Singh, Om Pal, E-mail: singhop@iitk.ac.in; Munshi, Prabhat

2016-11-15

Highlights: • Uncertainty analysis of reliability of Shutdown System is carried out. • Monte Carlo method of sampling is used. • The effect of various reliability improvement measures of SDS are accounted. - Abstract: In this paper, results are presented on the uncertainty evaluation of the reliability of Shutdown System (SDS) of a Medium Size Fast Breeder Reactor (MSFBR). The reliability analysis results are of Kumar et al. (2005). The failure rate of the components of SDS are taken from International literature and it is assumed that these follow log-normal distribution. Fault tree method is employed to propagate the uncertainty in failure rate from components level to shutdown system level. The beta factor model is used to account different extent of diversity. The Monte Carlo sampling technique is used for the analysis. The results of uncertainty analysis are presented in terms of the probability density function, cumulative distribution function, mean, variance, percentile values, confidence intervals, etc. It is observed that the spread in the probability distribution of SDS failure rate is less than SDS components failure rate and ninety percent values of the failure rate of SDS falls below the target value. As generic values of failure rates are used, sensitivity analysis is performed with respect to failure rate of control and safety rods and beta factor. It is discovered that a large increase in failure rate of SDS rods is not carried to SDS system failure proportionately. The failure rate of SDS is very sensitive to the beta factor of common cause failure between the two systems of SDS. The results of the study provide insight in the propagation of uncertainty in the failure rate of SDS components to failure rate of shutdown system.

Size matters: pitch dimensions constrain inter-team distances and surface area difference in small-sided soccer games

NARCIS (Netherlands)

Frencken, Wouter; van der Plaats, Jorrit; Visscher, Chris; Lemmink, Koen

2013-01-01

Pitch size varies in official soccer matches and differently sized pitches are adopted for tactical purposes in small-sided training games. Since interactive team behaviour emerges under con- straints, the authors evaluate the effect of pitch size (task) manipulations on interactive team behaviour

Uncertainty budget in internal monostandard NAA for small and large size samples analysis

International Nuclear Information System (INIS)

Dasari, K.B.; Acharya, R.

2014-01-01

Total uncertainty budget evaluation on determined concentration value is important under quality assurance programme. Concentration calculation in NAA or carried out by relative NAA and k0 based internal monostandard NAA (IM-NAA) method. IM-NAA method has been used for small and large sample analysis of clay potteries. An attempt was made to identify the uncertainty components in IM-NAA and uncertainty budget for La in both small and large size samples has been evaluated and compared. (author)

Social network analysis via multi-state reliability and conditional influence models

International Nuclear Information System (INIS)

Schneider, Kellie; Rainwater, Chase; Pohl, Ed; Hernandez, Ivan; Ramirez-Marquez, Jose Emmanuel

2013-01-01

This paper incorporates multi-state reliability measures into the assessment of a social network in which influence is treated as a multi-state commodity that flows through the network. The reliability of the network is defined as the probability that at least a certain level of influence reaches an intended target. We consider an individual's influence level as a function of the influence levels received from preceding actors in the network. We define several communication functions which describe the level of influence a particular actor will pass along to other actors within the network. Illustrative examples are presented, and the network reliability under the various communication influence levels is computed using exhaustive enumeration for a small example and Monte Carlo simulation for larger, more realistic sized examples.

Relationship marketing of small to medium sized textile retailers in the Northwest Province / Fred Angels Amulike Musika

OpenAIRE

Musika, Fred Angels Amulike

2002-01-01

This study concentrated on the concept of relationship marketing and its implementation by small and medium sized textile retailers in the Northwest province of South Africa. This study addressed the gap between the relationship marketing theory and its implementation by small and medium sized textile retailers in the textile industry of the Northwest province. Researchers in relationship marketing have started to realise that there is a definite need for detailed empirical ...

The minimum sit-to-stand height test: reliability, responsiveness and relationship to leg muscle strength.

Science.gov (United States)

Schurr, Karl; Sherrington, Catherine; Wallbank, Geraldine; Pamphlett, Patricia; Olivetti, Lynette

2012-07-01

To determine the reliability of the minimum sit-to-stand height test, its responsiveness and its relationship to leg muscle strength among rehabilitation unit inpatients and outpatients. Reliability study using two measurers and two test occasions. Secondary analysis of data from two clinical trials. Inpatient and outpatient rehabilitation services in three public hospitals. Eighteen hospital patients and five others participated in the reliability study. Seventy-two rehabilitation unit inpatients and 80 outpatients participated in the clinical trials. The minimum sit-to-stand height test was assessed using a standard procedure. For the reliability study, a second tester repeated the minimum sit-to-stand height test on the same day. In the inpatient clinical trial the measures were repeated two weeks later. In the outpatient trial the measures were repeated five weeks later. Knee extensor muscle strength was assessed in the clinical trials using a hand-held dynamometer. The reliability for the minimum sit-to-stand height test was excellent (intraclass correlation coefficient (ICC) 0.91, 95% confidence interval (CI) 0.81-0.96). The standard error of measurement was 34 mm. Responsiveness was moderate in the inpatient trial (effect size: 0.53) but small in the outpatient trial (effect size: 0.16). A small proportion (8-17%) of variability in minimum sit-to-stand height test was explained by knee extensor muscle strength. The minimum sit-to-stand height test has excellent reliability and moderate responsiveness in an inpatient rehabilitation setting. Responsiveness in an outpatient rehabilitation setting requires further investigation. Performance is influenced by factors other than knee extensor muscle strength.

Personnel role by implementing anti-crisis programs in small and medium-size enterprises

Directory of Open Access Journals (Sweden)

Pak Andrey Borisovitch

2011-08-01

Full Text Available To recover from crisis, small and medium-size enterprises have to develop anti-crisis plans and programs and to monitor the implementation process. The implementation efficiency is provided by the personnel which needs appraisal, motivation and development.

Bivariate Probit Models for Analysing how “Knowledge” Affects Innovation and Performance in Small and Medium Sized Firms

OpenAIRE

FARACE, Salvatore; MAZZOTTA, Fernanda

2011-01-01

This paper examines the determinants of innovation and its effects on small- and medium-sized firms We use the data from the OPIS databank, which provides a survey on a representative sample of firms from a province of the Southern Italy. We want to study whether small and medium sized firms can have a competitive advantage using their innovative capabilities, regardless of their sectoral and size limits. The main factor influencing the likelihood of innovation is knowledge, which is acquired...

78 FR 66950 - Trade Barriers That U.S. Small and Medium-Sized Enterprises Perceive as Affecting Exports to the...

Science.gov (United States)

2013-11-07

... report that catalogs trade barriers that U.S. small and medium-sized enterprises (SMEs) perceive as... INTERNATIONAL TRADE COMMISSION [Investigation No. 332-541] Trade Barriers That U.S. Small and Medium-Sized Enterprises Perceive as Affecting Exports to the European Union; Rescheduling of Washington...

Organisational culture as a part in the development of open innovation - the perspective of small and medium-sized enterprises

Directory of Open Access Journals (Sweden)

Szymańska Katarzyna

2016-05-01

Full Text Available The ability to introduce various concepts and business models is nowadays a prerequisite of creating a competitive advantage. This is to a large extent closely linked to the ability of enterprises to create, implement and disseminate a variety of innovative solutions. Today the use of open innovation is a necessity. This applies not only to large organisations, but also to small and medium-sized enterprises. In order to implement open innovation, small and medium-sized enterprises need to effectively manage their own growth through the preparation of appropriate strategies and the development of a model that encompasses all changes, taking into account a number of factors related to the growth dynamics of this sector. It is understood that an appropriate organisational culture plays an important role in the implementation of innovation in the sector of small and medium-sized enterprises. There are many indications that a cultural mismatch and misunderstanding are the main reasons for major problems related to the low level of implementation of innovation by small and medium-sized enterprises. The aim of the paper is to outline the issue of the impact of organisational culture on the development of the concept of open innovation in the sector of small and medium-sized enterprises.

Size of nuclear sources from measurements of proton-proton correlations at small relative momentum

International Nuclear Information System (INIS)

Rebreyend, D.; Kox, S.; Merchez, F.; Noren, B.; Perrin, C.; Khelfaoui, B.; Gondrand, J.C.; Bondorf, J.P.

1990-01-01

This contribution will present recent measurements performed on light heavy ion reactions at intermediate energies. Nuclear source sizes were determined by measuring the correlation at small relative momentum, between two protons detected in the EMRIC set-up. This technique allows the determination of the extent of the emitting source by constructing a correlation function for the coincident protons and analyzing it in the framework of a final state interaction model. We found the apparent source size to be large compared to the dimension of the studied system and low sensitivity of the extracted radii as a function of the target mass and detection angle. We will show that simulations may be needed to fully estimate the correlation induced by detectors with small angular acceptance

THE SOCIAL MEDIA IMPACT ON SMALL AND MEDIUM SIZED BUSINESSES

OpenAIRE

Mihai Alexandru Constantin Logofatu

2012-01-01

This paper aims to be a short introduction to social media and discusses on few ways in which small and medium sized businesses in Romania can take advantage of this hot topic. Through the use of social media every company can reach a global audience with less effort, time and money. In a world shaped more and more around social platforms the customer behaviour has completely and forever changed and those leaders and organizations that understand and embrace this new type of communication, co...

eLEARNING - A CHANCE FOR SMALL AND MEDIUM SIZED ENTERPRISES

OpenAIRE

Ileana Hamburg; Christiane Lindecke; Judith Terstriep

2005-01-01

eLearning through its flexibility and facility of access is seen as a major enabler of lifelong learning (LLL), as a catalyst of change and a chance for small and medium-sized enterprises (SMEs) to improve their business and to integrate into European market. But so far the eLearning in the context of vocational educational training has been mainly adopted by large enterprises, while only little activity can be observed in SMEs. The question arises what the chances and challenges for SMEs are...

Size ratio performance in detecting cerebral aneurysm rupture status is insensitive to small vessel removal.

Science.gov (United States)

Lauric, Alexandra; Baharoglu, Merih I; Malek, Adel M

2013-04-01

The variable definition of size ratio (SR) for sidewall (SW) vs bifurcation (BIF) aneurysms raises confusion for lesions harboring small branches, such as carotid ophthalmic or posterior communicating locations. These aneurysms are considered SW by many clinicians, but SR methodology classifies them as BIF. To evaluate the effect of ignoring small vessels and SW vs stringent BIF labeling on SR ruptured aneurysm detection performance in borderline aneurysms with small branches, and to reconcile SR-based labeling with clinical SW/BIF classification. Catheter rotational angiographic datasets of 134 consecutive aneurysms (60 ruptured) were automatically measured in 3-dimensional. Stringent BIF labeling was applied to clinically labeled aneurysms, with 21 aneurysms switching label from SW to BIF. Parent vessel size was evaluated both taking into account, and ignoring, small vessels. SR was defined accordingly as the ratio between aneurysm and parent vessel sizes. Univariate and multivariate statistics identified significant features. The square of the correlation coefficient (R(2)) was reported for bivariate analysis of alternative SR calculations. Regardless of SW/BIF labeling method, SR was equally significant in discriminating aneurysm ruptured status (P analysis of alternative SR had a high correlation of R(2) = 0.94 on the whole dataset, and R = 0.98 on the 21 borderline aneurysms. Ignoring small branches from SR calculation maintains rupture status detection performance, while reducing postprocessing complexity and removing labeling ambiguity. Aneurysms adjacent to these vessels can be considered SW for morphometric analysis. It is reasonable to use the clinical SW/BIF labeling when using SR for rupture risk evaluation.

Architectural Techniques to Enable Reliable and Scalable Memory Systems

OpenAIRE

Nair, Prashant J.

2017-01-01

High capacity and scalable memory systems play a vital role in enabling our desktops, smartphones, and pervasive technologies like Internet of Things (IoT). Unfortunately, memory systems are becoming increasingly prone to faults. This is because we rely on technology scaling to improve memory density, and at small feature sizes, memory cells tend to break easily. Today, memory reliability is seen as the key impediment towards using high-density devices, adopting new technologies, and even bui...

Irradiation tests of a small-sized motor with radiation resistance

International Nuclear Information System (INIS)

Nakamichi, M.; Ishitsuka, E.; Shimakawa, S.; Kan, S.

2007-01-01

In the Test Blanket Module (TBM) of the International Thermonuclear Experimental Reactor (ITER), tritium production and release behavior will be studied using neutrons from fusion reactions, as the blanket development for a demonstration (DEMO) reactor. For development of the TBM, in-pile functional tests are planned, including an integrated irradiation experiment of a fusion blanket mock-up for pulsed operation simulating the ITER operation mode, using the Japan Materials Testing Reactor (JMTR) of Japan Atomic Energy Agency (JAEA).Due to be installed in an irradiation rig, a small-sized motor has to be developed for rotating a neutron absorber with a window to realize the simulated pulse operation. Since degradation of materials of the motor may be caused by radiation damage due to neutron and gamma-ray irradiation, it is important to examine the soundness of the motor materials under the neutron and gamma irradiation.In the present study, a small-sized motor with increased radiation resistance was developed as follows. A design of a commercial alternate current (AC) servomotor was adopted in the base structure, and some components of the motor were replaced by those made of radiation-proof materials, through elimination of organic materials. Polyester-coated wire for field coil and epoxy for fixed resin were replaced by polyimide-coated wire and polysiloxane filled with MgO and Al 2 O 3 , respectively. Furthermore, inorganic lubricant (Mo-based coating of 4 micro meter in thickness) was treated on the surface of a gear, instead of organic (polyphenylether) oil.Radiation-induced degradation of the components of the developed small-sized motor was examined using JMTR and the Japan Research Reactor No.4 (JRR-4) of JAEA. The motor was operating normally up to a gamma-ray dose of 7 x 10 8 Gy, a fast neutron (E>1 MeV) fluence of 2 x 10 21 m -2 and a thermal neutron (E 22 m -2 . The irradiated gamma-ray dose for this motor is about 700 times as high as the operation

Job Stress in the United Kingdom: Are Small and Medium-Sized Enterprises and Large Enterprises Different?

Science.gov (United States)

Lai, Yanqing; Saridakis, George; Blackburn, Robert

2015-08-01

This paper examines the relationships between firm size and employees' experience of work stress. We used a matched employer-employee dataset (Workplace Employment Relations Survey 2011) that comprises of 7182 employees from 1210 private organizations in the United Kingdom. Initially, we find that employees in small and medium-sized enterprises experience lower level of overall job stress than those in large enterprises, although the effect disappears when we control for individual and organizational characteristics in the model. We also find that quantitative work overload, job insecurity and poor promotion opportunities, good work relationships and poor communication are strongly associated with job stress in the small and medium-sized enterprises, whereas qualitative work overload, poor job autonomy and employee engagements are more related with larger enterprises. Hence, our estimates show that the association and magnitude of estimated effects differ significantly by enterprise size. Copyright © 2013 John Wiley & Sons, Ltd.

Optimal sizing of small wind/battery systems considering the DC bus voltage stability effect on energy capture, wind speed variability, and load uncertainty

International Nuclear Information System (INIS)

Lujano-Rojas, Juan M.; Dufo-López, Rodolfo; Bernal-Agustín, José L.

2012-01-01

Highlights: ► We propose a mathematical model for optimal sizing of small wind energy systems. ► No other previous work has considered all the aspects included in this paper. ► The model considers several parameters about batteries. ► Wind speed variability is considered by means of ARMA model. ► The results show how to minimize the expected energy that is not supplied. - Abstract: In this paper, a mathematical model for stochastic simulation and optimization of small wind energy systems is presented. This model is able to consider the operation of the charge controller, the coulombic efficiency during charge and discharge processes, the influence of temperature on the battery bank capacity, the wind speed variability, and load uncertainty. The joint effect of charge controller operation, ambient temperature, and coulombic efficiency is analyzed in a system installed in Zaragoza (Spain), concluding that if the analysis without considering these factors is carried out, the reliability level of the physical system could be lower than expected, and an increment of 25% in the battery bank capacity would be required to reach a reliability level of 90% in the analyzed case. Also, the effect of the wind speed variability and load uncertainty in the system reliability is analyzed. Finally, the uncertainty in the battery bank lifetime and its effect on the net present cost are discussed. The results showed that, considering uncertainty of 17.5% in the battery bank lifetime calculated using the Ah throughput model, about 12% of uncertainty in the net present cost is expected. The model presented in this research could be a useful stochastic simulation and optimization tool that allows the consideration of important uncertainty factors in techno-economic analysis.

Transformational and transactional leadership: does it work in small to medium-sized enterprises?

NARCIS (Netherlands)

Mesu, J.K.

2013-01-01

Using a sample of 755 employees who rated 121 supervisors within 50 Dutch small and medium-sized enterprises (SMEs), this dissertation intends to fill in some of the existing gaps in the literature. Firstly, by investigating whether the impact of transformational and transactional leadership extends

Hedging Behavior in Small and Medium-sized Enterprises: The Role of Unobserved Heterogeneity

NARCIS (Netherlands)

Pennings, J.M.E.; Garcia, P.

2004-01-01

Abstract We investigate factors that drive derivative usage in small and medium-sized enterprises (SMEs). The influence of these factors on hedging behavior cannot a priori be assumed equal for all SMEs. To address this heterogeneity, a generalized mixture regression model is used which classifies

Presenting a Framework to Analyze Local Climate Policy and Action in Small and Medium-Sized Cities

NARCIS (Netherlands)

Hoppe, Thomas; van der Vegt, Arjen; Stegmaier, Peter

2016-01-01

Academic attention to local climate policy usually focuses on large-sized cities. Given the climate challenges ahead this seems unjustified. Small and medium-sized cities (SMCs) deserve scholarly attention as well. The main question is: What factors influence climate change policy and local climate

Presenting a framework to analyze local climate policy and action in small and medium-sized cities

NARCIS (Netherlands)

Hoppe, T.; van der Vegt, Arjen; Stegmaier, Peter

2016-01-01

Academic attention to local climate policy usually focuses on large-sized cities. Given the climate challenges ahead this seems unjustified. Small and medium-sized cities (SMCs) deserve scholarly attention as well. The main question is: What factors influence climate change policy and local

Spatial distribution and size of small canopy gaps created by Japanese black bears: estimating gap size using dropped branch measurements.

Science.gov (United States)

Takahashi, Kazuaki; Takahashi, Kaori

2013-06-10

Japanese black bears, a large-bodied omnivore, frequently create small gaps in the tree crown during fruit foraging. However, there are no previous reports of black bear-created canopy gaps. To characterize physical canopy disturbance by black bears, we examined a number of parameters, including the species of trees in which canopy gaps were created, gap size, the horizontal and vertical distribution of gaps, and the size of branches broken to create gaps. The size of black bear-created canopy gaps was estimated using data from branches that had been broken and dropped on the ground. The disturbance regime was characterized by a highly biased distribution of small canopy gaps on ridges, a large total overall gap area, a wide range in gap height relative to canopy height, and diversity in gap size. Surprisingly, the annual rate of bear-created canopy gap formation reached 141.3 m2 ha-1 yr-1 on ridges, which were hot spots in terms of black bear activity. This rate was approximately 6.6 times that of tree-fall gap formation on ridges at this study site. Furthermore, this rate was approximately two to three times that of common tree-fall gap formation in Japanese forests, as reported in other studies. Our findings suggest that the ecological interaction between black bears and fruit-bearing trees may create a unique light regime, distinct from that created by tree falls, which increases the availability of light resources to plants below the canopy.

Effects of kinship or familiarity? Small thrips larvae experience lower predation risk only in groups of mixed-size siblings

NARCIS (Netherlands)

de Bruijn, P.J.A.; Sabelis, M.W.; Egas, M.

2014-01-01

In many species of insects, larvae are distributed in an aggregated fashion. As they may differ in size and size matters to predation risk, small larvae may be less likely to fall prey to predators when near large and therefore better-defended larvae. We hypothesize that the small larvae may profit

Favouring Small and Medium Sized Enterprises with Directive 2014/24/EU

OpenAIRE

Trybus, Martin; Andrecka, Marta

2017-01-01

This article argues that the four main measures introduced in the 2014 reform of the Procurement Directives to promote Small andMediumSized Enterprises (SMEs) cannot be classified as measures favouring SMEs. A measure favours SMEs when it compromises the main objectives of competition, non-discrimination and value for money. The discussion covers the regimes on the division of larger contracts into lots, the European Single Procurement Document (ESPD), minimum turnover requirements, and direc...

Exploring the Usage of CSR in Small and Medium-Sized Companies

OpenAIRE

Perälä, Veera; Saukkonen, Anna-Reetta

2017-01-01

The objective of this study was to examine how small and medium sized companies understood the concept of corporate social responsibility and how they incorporated it in their business strategies. The topical nature of this subject made it interesting and worth researching. In addition to discovering ideas about CSR, the study also focused on marketing communications and the competitive advantage that CSR provides. The methodological approach used in the study was that of qualitative resea...

Design of an interdisciplinary engineering elective scoped around collaboration with Small Medium Sized enterprises (SME)

DEFF Research Database (Denmark)

Christiansen, Nynne Budtz; Ulrich, Mai-Mai; Pontoppidan, Maja Lund

2014-01-01

a real life setting elective course, involving small and medium sized enterprises (SME) in engineering education. How do you engage with companies without compromising the learning outcome? How you manage the expectation from the companies and still maintaining the student responsibility for the problem...... of a compulsory 10 ECTS element with focus on interdisciplinary and industry collaboration for all Bachelors of Engineering at The Technical University of Denmark in 2016. As collaboration partner the elective has chosen to work with small and medium sized enterprises (SME) as more than half of the value added...... to the European economy comes from the SME’s and around half of all employees work in micro or small businesses with less than 50 employees5. At the same time the barriers for university collaboration with SMEs are somewhat steeper than working with larger organizations6. The paper will focus on the SME...

Innovativeness of small and medium-sized enterprises in the Republic of Serbia and countries of the European Union

Directory of Open Access Journals (Sweden)

Nikolić Miroljub

2015-01-01

Full Text Available The paper provides a comparative analysis of the results of innovation activities in enterprises of different size from EU member and candidate states during the period 2008-2010. Particularly, the paper considers position of Serbia compared to the EU average and average of some neighboring countries (Hungary, Slovenia, Croatia, Romania and Bulgaria. The results confirmed the existence of a high correlation between size of enterprise and its innovation activities. The percentage of innovation activities in large enterprises is higher than in small enterprises. Serbia is lagging behind the EU average, regarding innovativeness level in all types of enterprises (classified by size. However, when Serbia is compared to neighboring countries, the situation is much different. Small enterprises from Serbia are more innovative than small enterprises from neighboring countries. The situation is similar in medium-sized enterprises. Large enterprises from Serbia are more innovative than enterprises from Bulgaria, Hungary and Romania, and less innovative than large enterprises from Slovenia and Croatia.

Analysis of small sample size studies using nonparametric bootstrap test with pooled resampling method.

Science.gov (United States)

Dwivedi, Alok Kumar; Mallawaarachchi, Indika; Alvarado, Luis A

2017-06-30

Experimental studies in biomedical research frequently pose analytical problems related to small sample size. In such studies, there are conflicting findings regarding the choice of parametric and nonparametric analysis, especially with non-normal data. In such instances, some methodologists questioned the validity of parametric tests and suggested nonparametric tests. In contrast, other methodologists found nonparametric tests to be too conservative and less powerful and thus preferred using parametric tests. Some researchers have recommended using a bootstrap test; however, this method also has small sample size limitation. We used a pooled method in nonparametric bootstrap test that may overcome the problem related with small samples in hypothesis testing. The present study compared nonparametric bootstrap test with pooled resampling method corresponding to parametric, nonparametric, and permutation tests through extensive simulations under various conditions and using real data examples. The nonparametric pooled bootstrap t-test provided equal or greater power for comparing two means as compared with unpaired t-test, Welch t-test, Wilcoxon rank sum test, and permutation test while maintaining type I error probability for any conditions except for Cauchy and extreme variable lognormal distributions. In such cases, we suggest using an exact Wilcoxon rank sum test. Nonparametric bootstrap paired t-test also provided better performance than other alternatives. Nonparametric bootstrap test provided benefit over exact Kruskal-Wallis test. We suggest using nonparametric bootstrap test with pooled resampling method for comparing paired or unpaired means and for validating the one way analysis of variance test results for non-normal data in small sample size studies. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

Monte Carlo modeling of small photon fields: Quantifying the impact of focal spot size on source occlusion and output factors, and exploring miniphantom design for small-field measurements

International Nuclear Information System (INIS)

Scott, Alison J. D.; Nahum, Alan E.; Fenwick, John D.

2009-01-01

The accuracy with which Monte Carlo models of photon beams generated by linear accelerators (linacs) can describe small-field dose distributions depends on the modeled width of the electron beam profile incident on the linac target. It is known that the electron focal spot width affects penumbra and cross-field profiles; here, the authors explore the extent to which source occlusion reduces linac output for smaller fields and larger spot sizes. A BEAMnrc Monte Carlo linac model has been used to investigate the variation in penumbra widths and small-field output factors with electron spot size. A formalism is developed separating head scatter factors into source occlusion and flattening filter factors. Differences between head scatter factors defined in terms of in-air energy fluence, collision kerma, and terma are explored using Monte Carlo calculations. Estimates of changes in kerma-based source occlusion and flattening filter factors with field size and focal spot width are obtained by calculating doses deposited in a narrow 2 mm wide virtual ''milliphantom'' geometry. The impact of focal spot size on phantom scatter is also explored. Modeled electron spot sizes of 0.4-0.7 mm FWHM generate acceptable matches to measured penumbra widths. However the 0.5 cm field output factor is quite sensitive to electron spot width, the measured output only being matched by calculations for a 0.7 mm spot width. Because the spectra of the unscattered primary (Ψ Π ) and head-scattered (Ψ Σ ) photon energy fluences differ, miniphantom-based collision kerma measurements do not scale precisely with total in-air energy fluence Ψ=(Ψ Π +Ψ Σ ) but with (Ψ Π +1.2Ψ Σ ). For most field sizes, on-axis collision kerma is independent of the focal spot size; but for a 0.5 cm field size and 1.0 mm spot width, it is reduced by around 7% mostly due to source occlusion. The phantom scatter factor of the 0.5 cm field also shows some spot size dependence, decreasing by 6% (relative) as

Early outcome in renal transplantation from large donors to small and size-matched recipients - a porcine experimental model

DEFF Research Database (Denmark)

Ravlo, Kristian; Chhoden, Tashi; Søndergaard, Peter

2012-01-01

in small recipients within 60 min after reperfusion. Interestingly, this was associated with a significant reduction in medullary RPP, while there was no significant change in the size-matched recipients. No difference was observed in urinary NGAL excretion between the groups. A significant higher level......Kidney transplantation from a large donor to a small recipient, as in pediatric transplantation, is associated with an increased risk of thrombosis and DGF. We established a porcine model for renal transplantation from an adult donor to a small or size-matched recipient with a high risk of DGF...... and studied GFR, RPP using MRI, and markers of kidney injury within 10 h after transplantation. After induction of BD, kidneys were removed from ∼63-kg donors and kept in cold storage for ∼22 h until transplanted into small (∼15 kg, n = 8) or size-matched (n = 8) recipients. A reduction in GFR was observed...

A survey of the use of operational research in decisions made by micro, small and medium-sized enterprises in Macedonia

Directory of Open Access Journals (Sweden)

Violeta Cvetkoska

2016-12-01

Full Text Available We live in a complex world and managers of organizations are constantly facing numerous challenges. Good decisions, i.e., better outcomes for organizations, require use of the powerful discipline Operational Research (OR/Management Science (MS. Organizations applying this discipline have achieved significant benefits such as cost reduction, increased revenues, increased market share, higher quality, improved productivity, improved performance, better customer service, etc. The aim of this paper is to examine whether managers of micro, small and medium-sized enterprises in Macedonia use OR models for supporting decision-making processes, where OR models, methods and techniques are commonly used, and what benefits achieved in using quantitative OR models, methods and techniques. The survey was conducted using a questionnaire distributed electronically to 100 managers of micro, 100 managers of small and 100 managers of medium-sized enterprises. The questionnaires were answered completely by 93 managers of the micro, 73 managers of the small and 71 managers of the medium-sized enterprises, and the questionnaire responses were subsequently analyzed. The answers showed that decisions on running enterprises are made intuitively by 90% of managers of the micro, 78% of managers of the small, and 55% of managers of the medium-sized enterprises, while quantitative OR models for supporting the decision-making process are used by 10% of managers of the micro, 22% of managers of the small, and 45% of managers of the medium-sized enterprises. Applied in the micro, small and medium-sized enterprises are inventory models, time series analysis and forecasting, whereas micro and medium-sized enterprises rely on decision analysis. Small and medium-sized enterprises use break-even analysis, assignation, linear programming, and project management. The OR models and methods used in running the respective enterprises led to the following results: optimal inventory

Current information technology needs of small to medium sized apparel manufacturers and contractors

Energy Technology Data Exchange (ETDEWEB)

Wipple, C.; Vosti, E.

1997-11-01

This report documents recent efforts of the American Textile Partnership (AMTEX) Demand Activated Manufacturing Architecture (DAMA) Project to address needs that are characterized of small to medium sized apparel manufactures and contractors. Background on the AMTEX/DAMA project and objectives for this specific efforts are discussed.

Batched Triangular Dense Linear Algebra Kernels for Very Small Matrix Sizes on GPUs

KAUST Repository

Charara, Ali; Keyes, David E.; Ltaief, Hatem

2017-01-01

Batched dense linear algebra kernels are becoming ubiquitous in scientific applications, ranging from tensor contractions in deep learning to data compression in hierarchical low-rank matrix approximation. Within a single API call, these kernels are capable of simultaneously launching up to thousands of similar matrix computations, removing the expensive overhead of multiple API calls while increasing the occupancy of the underlying hardware. A challenge is that for the existing hardware landscape (x86, GPUs, etc.), only a subset of the required batched operations is implemented by the vendors, with limited support for very small problem sizes. We describe the design and performance of a new class of batched triangular dense linear algebra kernels on very small data sizes using single and multiple GPUs. By deploying two-sided recursive formulations, stressing the register usage, maintaining data locality, reducing threads synchronization and fusing successive kernel calls, the new batched kernels outperform existing state-of-the-art implementations.

Batched Triangular Dense Linear Algebra Kernels for Very Small Matrix Sizes on GPUs

KAUST Repository

Charara, Ali

2017-03-06

Batched dense linear algebra kernels are becoming ubiquitous in scientific applications, ranging from tensor contractions in deep learning to data compression in hierarchical low-rank matrix approximation. Within a single API call, these kernels are capable of simultaneously launching up to thousands of similar matrix computations, removing the expensive overhead of multiple API calls while increasing the occupancy of the underlying hardware. A challenge is that for the existing hardware landscape (x86, GPUs, etc.), only a subset of the required batched operations is implemented by the vendors, with limited support for very small problem sizes. We describe the design and performance of a new class of batched triangular dense linear algebra kernels on very small data sizes using single and multiple GPUs. By deploying two-sided recursive formulations, stressing the register usage, maintaining data locality, reducing threads synchronization and fusing successive kernel calls, the new batched kernels outperform existing state-of-the-art implementations.

A combined Importance Sampling and Kriging reliability method for small failure probabilities with time-demanding numerical models

International Nuclear Information System (INIS)

Echard, B.; Gayton, N.; Lemaire, M.; Relun, N.

2013-01-01

Applying reliability methods to a complex structure is often delicate for two main reasons. First, such a structure is fortunately designed with codified rules leading to a large safety margin which means that failure is a small probability event. Such a probability level is difficult to assess efficiently. Second, the structure mechanical behaviour is modelled numerically in an attempt to reproduce the real response and numerical model tends to be more and more time-demanding as its complexity is increased to improve accuracy and to consider particular mechanical behaviour. As a consequence, performing a large number of model computations cannot be considered in order to assess the failure probability. To overcome these issues, this paper proposes an original and easily implementable method called AK-IS for active learning and Kriging-based Importance Sampling. This new method is based on the AK-MCS algorithm previously published by Echard et al. [AK-MCS: an active learning reliability method combining Kriging and Monte Carlo simulation. Structural Safety 2011;33(2):145–54]. It associates the Kriging metamodel and its advantageous stochastic property with the Importance Sampling method to assess small failure probabilities. It enables the correction or validation of the FORM approximation with only a very few mechanical model computations. The efficiency of the method is, first, proved on two academic applications. It is then conducted for assessing the reliability of a challenging aerospace case study submitted to fatigue.

Status and Prospects for Small and Medium Sized Reactors

International Nuclear Information System (INIS)

Kupitz, J.; Arkhipov, V.; Brey, H. L.

1998-01-01

There is considerable interest by Member States in the continued development of small and medium sized reactors (SMRs) as a significant energy sources for the future. The support for this programme within the IAEA was recently reaffirmed at the 1997 General Conference. Although the generation of electricity has been predominant focus of existing SMRs, there is increasing interest in using these plants for other applications such as desalination, district heating and hydrogen production from the reforming of methane. Addressed herein is a review of ongoing SMR development activities within selected Member States, an overview of the Agency's SMR programme and a discussion of selected SMR designs with emphasis on their safety attributes. (author)

Shrinkage of body size of small insects: A possible link to global warming?

International Nuclear Information System (INIS)

He Jihuan

2007-01-01

The increase of global mean surface temperature leads to the increase of metabolic rate. This might lead to an unexpected threat from the small insect world. Global warming shrinks cell size, shorten lifespan, and accelerate evolution. The present note speculates on possible connections between allometry and E-infinity theory

Uniform fabrication of thick SU-8 patterns on small-sized wafers for micro-optics applications

Science.gov (United States)

Abada, S.; Reig, B.; Daran, E.; Doucet, JB; Camps, T.; Charlot, S.; Bardinal, V.

2014-05-01

This paper reports on an alternative method for precise and uniform fabrication of 100μm-thick SU-8 microstructures on small-sized or non-circular samples. Standard spin-coating of high-viscosity resists is indeed known to induce large edge beads, leading to an air gap between the mask and the SU-8 photo-resist surface during UV photolithography. This results in a non uniform thickness deposition and in a poor pattern definition. This problem becomes highly critical in the case of small-sized samples. To overcome it, we have developed a soft thermal imprint method based on the use of a nano-imprint equipment and applicable whatever sample fragility, shape and size (from 2cm to 6 inches). After final photolithography, the SU8 pattern thickness variation profile is measured. Thickness uniformity is improved from 30% to 5% with a 5μm maximal deviation to the target value over 2cm-long samples.

Reliability of fish size estimates obtained from multibeam imaging sonar

Science.gov (United States)

Hightower, Joseph E.; Magowan, Kevin J.; Brown, Lori M.; Fox, Dewayne A.

2013-01-01

Multibeam imaging sonars have considerable potential for use in fisheries surveys because the video-like images are easy to interpret, and they contain information about fish size, shape, and swimming behavior, as well as characteristics of occupied habitats. We examined images obtained using a dual-frequency identification sonar (DIDSON) multibeam sonar for Atlantic sturgeon Acipenser oxyrinchus oxyrinchus, striped bass Morone saxatilis, white perch M. americana, and channel catfish Ictalurus punctatus of known size (20–141 cm) to determine the reliability of length estimates. For ranges up to 11 m, percent measurement error (sonar estimate – total length)/total length × 100 varied by species but was not related to the fish's range or aspect angle (orientation relative to the sonar beam). Least-square mean percent error was significantly different from 0.0 for Atlantic sturgeon (x̄  =  −8.34, SE  =  2.39) and white perch (x̄  = 14.48, SE  =  3.99) but not striped bass (x̄  =  3.71, SE  =  2.58) or channel catfish (x̄  = 3.97, SE  =  5.16). Underestimating lengths of Atlantic sturgeon may be due to difficulty in detecting the snout or the longer dorsal lobe of the heterocercal tail. White perch was the smallest species tested, and it had the largest percent measurement errors (both positive and negative) and the lowest percentage of images classified as good or acceptable. Automated length estimates for the four species using Echoview software varied with position in the view-field. Estimates tended to be low at more extreme azimuthal angles (fish's angle off-axis within the view-field), but mean and maximum estimates were highly correlated with total length. Software estimates also were biased by fish images partially outside the view-field and when acoustic crosstalk occurred (when a fish perpendicular to the sonar and at relatively close range is detected in the side lobes of adjacent beams). These sources of

submitter A High Precision 3D Magnetic Field Scanner for Small to Medium Size Magnets

CERN Document Server

Bergsma, F; Garnier, F; Giudici, P A

2016-01-01

A bench to measure the magnetic field of small to-medium-sized magnets with high precision was built. It uses a small-sized head with three orthogonal Hall probes, supported on a long pole at continuous movement during measurement. The head is calibrated in three dimensions by rotation over the full solid angle in a special device. From 0 to 2.5 T, the precision is ±0.2 mT in all components. The spatial range is 1 × 1 × 2 m with precision of ±0.02 mm. The bench and its controls are lightweight and easy to transport. The head can penetrate through small apertures and measure as close as 0.5 mm from the surface of a magnet. The bench can scan complicated grids in Cartesian or cylindrical coordinates, steered by a simple text file on an accompanying PC. The raw data is online converted to magnetic units and stored in a text file.

SIMPLIFIED MATHEMATICAL MODEL OF SMALL SIZED UNMANNED AIRCRAFT VEHICLE LAYOUT

Directory of Open Access Journals (Sweden)

2016-01-01

Full Text Available Strong reduction of new aircraft design period using new technology based on artificial intelligence is the key problem mentioned in forecasts of leading aerospace industry research centers. This article covers the approach to devel- opment of quick aerodynamic design methods based on artificial intelligence neural system. The problem is being solved for the classical scheme of small sized unmanned aircraft vehicle (UAV. The principal parts of the method are the mathe- matical model of layout, layout generator of this type of aircraft is built on aircraft neural networks, automatic selection module for cleaning variety of layouts generated in automatic mode, robust direct computational fluid dynamics method, aerodynamic characteristics approximators on artificial neural networks.Methods based on artificial neural networks have intermediate position between computational fluid dynamics methods or experiments and simplified engineering approaches. The use of ANN for estimating aerodynamic characteris-tics put limitations on input data. For this task the layout must be presented as a vector with dimension not exceeding sev-eral hundred. Vector components must include all main parameters conventionally used for layouts description and com- pletely replicate the most important aerodynamics and structural properties.The first stage of the work is presented in the paper. Simplified mathematical model of small sized UAV was developed. To estimate the range of geometrical parameters of layouts the review of existing vehicle was done. The result of the work is the algorithm and computer software for generating the layouts based on ANN technolo-gy. 10000 samples were generated and the dataset containig geometrical and aerodynamic characteristics of layoutwas created.

Structure of Small and Medium-Sized Business: Results of Total Statistic Observations in Russia

Directory of Open Access Journals (Sweden)

Iuliia S. Pinkovetskaia

2018-03-01

Full Text Available The aim of the research is estimation of regularities and tendencies, characteristic for modern sectoral structure of small and mediumsized business in Russia. The subject of the research is a set of processes of structural changes on the types of economic activities of such enterprises, as well as the differentiation of the number of employees in enterprises. The research methodology included consideration of aggregates of subjects of small and medium-sized business, formed according to sectoral and territorial features. As the initial data used the official statistical information, which was obtain in the course of total observation of the activities of small and medium-sized businesses in 2010 and 2015. The study was conducted on indicators characterizing the full range of legal entities and individual entrepreneurs in the country. The materiality of structural changes was carried out on the basis of the Ryabtsev index. Modeling the differentiation of the values of the number of employees per enterprise was based on the development of density normal distribution functions. According to the hypothesis it is assumed that the differentiation of the number of employees working in enterprises depend on six main types of economic activity and on the subjects of Russia. Based on the results of the study was proved that there are no significant structural changes for the period from 2010 to 2015, both in terms of the number of enterprises and the number of their employees. Based on the results of the simulation, the average values of the number of employees for the six main types of activity were established, as well as the intervals for changing these indicators for the aggregates of small and medium-sized enterprises located in the majority of the country's subjects. The results of research can be used in the performance of scientific works related to the justification of the expected number and number of employees of enterprises, the formation of

Corporate social responsibility and small-medium sized enterprises: evidence from Greece

Directory of Open Access Journals (Sweden)

Electra Pitoska

2018-03-01

Full Text Available This paper is a qualitative empirical research of Greek Small and Medium-sized Enterprises (SMEs and examines their dominant perceptions and attitudes towards Corporate Social Responsibility (CSR. The research was conducted in the Region of Western Macedonia, North Greece, via personal interviews based on a structured questionnaire, which was completed by 420 enterprises, with different business functions, and were randomly chosen from local Chamber registers. The results demonstrated that, as Greek SMEs in the periphery have not decided on a particular strategy for Social Responsibility practices, CSR is frequently defined as sponsorship or charity programmes. The research also revealed the restraining factors for SMEs in implementing CSR policies: financial cost, small size of enterprises, absence of specialized partners, and poor supporting role of public authorities. Whereas, the most significant non-financial goals for the enterprises attempting to implement CSR in Greece are: responsibility and respect to customers, promotion of sustainability, environmentally-friendly practices; human resources and protection of rights are less emphasized. Interestingly, more than 80% of the subjects hold that engaging in CSR practices in the current financial context is vital. With regard to the benefits resulting from CSR, the research demonstrated that: Enhancing ‘corporate image’, ‘business performance’, and ‘customer satisfaction’ are significant. Nevertheless, the research highlighted that implementing CSR strategies are rather positively than strongly correlated with the benefits deriving from CSR.

Stochastic Differential Equation-Based Flexible Software Reliability Growth Model

Directory of Open Access Journals (Sweden)

P. K. Kapur

2009-01-01

Full Text Available Several software reliability growth models (SRGMs have been developed by software developers in tracking and measuring the growth of reliability. As the size of software system is large and the number of faults detected during the testing phase becomes large, so the change of the number of faults that are detected and removed through each debugging becomes sufficiently small compared with the initial fault content at the beginning of the testing phase. In such a situation, we can model the software fault detection process as a stochastic process with continuous state space. In this paper, we propose a new software reliability growth model based on Itô type of stochastic differential equation. We consider an SDE-based generalized Erlang model with logistic error detection function. The model is estimated and validated on real-life data sets cited in literature to show its flexibility. The proposed model integrated with the concept of stochastic differential equation performs comparatively better than the existing NHPP-based models.

Bridging the Gap between Universities of Professional Education and Small- and Medium-Sized Enterprises

NARCIS (Netherlands)

Masurel, E.; Nijkamp, P.

2011-01-01

Improving the relationship between knowledge institutions (especially Universities of Professional Education, UPE) and Small-and Medium-sized Enterprises (SMEs) is one of the challenges of current economic policy. Innovation is an important aspect of this policy. However, the characteristics of both

Optimal sizing of a run-of-river small hydropower plant

International Nuclear Information System (INIS)

Anagnostopoulos, John S.; Papantonis, Dimitris E.

2007-01-01

The sizing of a small hydropower plant of the run-of-river type is very critical for the cost effectiveness of the investment. In the present work, a numerical method is used for the optimal sizing of such a plant that comprises two hydraulic turbines operating in parallel, which can be of different type and size in order to improve its efficiency. The study and analysis of the plant performance is conducted using a newly developed evaluation algorithm that simulates in detail the plant operation during the year and computes its production results and economic indices. A parametric study is performed first in order to quantify the impact of some important construction and operation factors. Next, a stochastic evolutionary algorithm is implemented for the optimization process. The examined optimization problem uses data of a specific site and is solved in the single and two-objective modes, considering, together with economic, some additional objectives, as maximization of the produced energy and the best exploitation of the water stream potential. Analyzing the results of various optimizations runs, it becomes possible to identify the most advantageous design alternatives to realize the project. It was found that the use of two turbines of different size can enhance sufficiently both the energy production of the plant and the economic results of the investment. Finally, the sensitivity of the plant performance to other external parameters can be easily studied with the present method, and some indicative results are given for different financial or hydrologic conditions

Toward a Singleton Undergraduate Computer Graphics Course in Small and Medium-Sized Colleges

Science.gov (United States)

Shesh, Amit

2013-01-01

This article discusses the evolution of a single undergraduate computer graphics course over five semesters, driven by a primary question: if one could offer only one undergraduate course in graphics, what would it include? This constraint is relevant to many small and medium-sized colleges that lack resources, adequate expertise, and enrollment…

The Dilemma and Way-Out of Urban and Rural Planning Management in China’s Small and Medium-Sized Cities

Institute of Scientific and Technical Information of China (English)

Dawei; WANG; Yandong; WANG

2014-01-01

In China, for small and medium-sized cities, urban and rural planning management should play an important role during the process of urbanization. However, it failed to do that in reality due to a series of limits, such as local fiscal deficiency, scarce human resources, incomplete management systems, historic planning defects, inadequate supervisions, and imperfect regulations, etc. This paper made a comprehensive analysis on the dilemma of urban and rural planning management in China’s small and medium-sized cities and the interests and status of the government, enterprises and public in space resource allocation and put forward the methods to improve the quality of planning management in China’s small and medium-sized cities from the view of systems and mechanisms.

The effect of feeding position and body size on the capacity of small ...

African Journals Online (AJOL)

The effect of feeding position and body size on the capacity of small ruminants to reach, for food when fed through barriers. ... The barrier allowed the neck to pass through, but not the shoulders. It was hypothesized that goats would have larger reach than sheep and that for each species, horizontal reach forwards, F, ...

SIERRA - A 3-D device simulator for reliability modeling

Science.gov (United States)

Chern, Jue-Hsien; Arledge, Lawrence A., Jr.; Yang, Ping; Maeda, John T.

1989-05-01

SIERRA is a three-dimensional general-purpose semiconductor-device simulation program which serves as a foundation for investigating integrated-circuit (IC) device and reliability issues. This program solves the Poisson and continuity equations in silicon under dc, transient, and small-signal conditions. Executing on a vector/parallel minisupercomputer, SIERRA utilizes a matrix solver which uses an incomplete LU (ILU) preconditioned conjugate gradient square (CGS, BCG) method. The ILU-CGS method provides a good compromise between memory size and convergence rate. The authors have observed a 5x to 7x speedup over standard direct methods in simulations of transient problems containing highly coupled Poisson and continuity equations such as those found in reliability-oriented simulations. The application of SIERRA to parasitic CMOS latchup and dynamic random-access memory single-event-upset studies is described.

The role of small and medium-sized high-tech enterprise in the formation of innovative potential of the Voronezh region

Directory of Open Access Journals (Sweden)

E. A. Shubina

2016-01-01

Full Text Available In modern conditions the region's sustainable development and economic growth is largely determined by its ability to implement innovations. One of the determining factors of long-term economic development of the territories, to date, is innovation. A mechanism to give impetus to the innovative development of the regions is to create effective small and medium-sized innovative enterprises. Voronezh region, like many Russian regions, has considerable potential for innovation, but usually it is not used efficiently or not used at all. The article deals with the concept and the need to develop innovative entrepreneurship and the role of small and medium innovative enterprises in the formation of scientific and technical potential of the Voronezh region. The basic conditions and factors promoting and impeding the development of small and medium innovative businesses in the region, determined the willingness of subjects of innovation activity in the development, implementation and promotion of innovation in the region. The problems of development of small and medium-sized businesses at the regional level. The evaluation of actions to improve SMEs management programs in the region. Particular attention is given to the classification of small and medium-sized innovative business structures. In order to stimulate the development of small and medium-sized innovative business in the Voronezh region in the article suggests the implementation of a package of measures. The active use of innovation by small and medium-sized enterprises of the Voronezh area enhances their efficiency and competitiveness, creates new jobs, which ultimately has a positive effect on the region's economic development, the growth of the tax base, improving the quality of life of the population.

Core and shell sizing of small silver-coated nanospheres by optical extinction spectroscopy

International Nuclear Information System (INIS)

Schinca, D C; Scaffardi, L B

2008-01-01

Silver metal nanoparticles (Nps) are extensively used in different areas of research and technology due to their interesting optical, thermal and electric properties, especially for bare core and core-shell nanostructures with sizes smaller than 10 nm. Since these properties are core-shell size-dependent, size measurement is important in manipulating their potential functionalization and applications. Bare and coated small silver Nps fabricated by physical and chemical methods present specific characteristics in their extinction spectra that are potentially useful for sizing purposes. This work presents a novel procedure to size mean core radius smaller than 10 nm and mean shell thickness of silver core-shell Nps based on a comparative study of the characteristics in their optical extinction spectra in different media as a function of core radii, shell thickness and coating refractive index. From the regularities derived from these relationships, it can be concluded that plasmon full width at half-maximum (FWHM) is sensitive to core size but not to coating thickness, while plasmon resonance wavelength (PRW) is related to shell thickness and mostly independent of core radius. These facts, which allow sizing simultaneously both mean core radius and shell thickness, can also be used to size bare silver Nps as a special case of core-shell Nps with zero shell thickness. The proposed method was applied to size experimental samples and the results show good agreement with conventional TEM microscopy.

Assessing learning in small sized physics courses

Directory of Open Access Journals (Sweden)

Emanuela Ene

2018-01-01

Full Text Available We describe the construction, validation, and testing of a concept inventory for an Introduction to Physics of Semiconductors course offered by the department of physics to undergraduate engineering students. By design, this inventory addresses both content knowledge and the ability to interpret content via different cognitive processes outlined in Bloom’s revised taxonomy. The primary challenge comes from the low number of test takers. We describe the Rasch modeling analysis for this concept inventory, and the results of the calibration on a small sample size, with the intention of providing a useful blueprint to other instructors. Our study involved 101 students from Oklahoma State University and fourteen faculty teaching or doing research in the field of semiconductors at seven universities. The items were written in four-option multiple-choice format. It was possible to calibrate a 30-item unidimensional scale precisely enough to characterize the student population enrolled each semester and, therefore, to allow the tailoring of the learning activities of each class. We show that this scale can be employed as an item bank from which instructors could extract short testlets and where we can add new items fitting the existing calibration.

Assessing learning in small sized physics courses

Science.gov (United States)

Ene, Emanuela; Ackerson, Bruce J.

2018-01-01

We describe the construction, validation, and testing of a concept inventory for an Introduction to Physics of Semiconductors course offered by the department of physics to undergraduate engineering students. By design, this inventory addresses both content knowledge and the ability to interpret content via different cognitive processes outlined in Bloom's revised taxonomy. The primary challenge comes from the low number of test takers. We describe the Rasch modeling analysis for this concept inventory, and the results of the calibration on a small sample size, with the intention of providing a useful blueprint to other instructors. Our study involved 101 students from Oklahoma State University and fourteen faculty teaching or doing research in the field of semiconductors at seven universities. The items were written in four-option multiple-choice format. It was possible to calibrate a 30-item unidimensional scale precisely enough to characterize the student population enrolled each semester and, therefore, to allow the tailoring of the learning activities of each class. We show that this scale can be employed as an item bank from which instructors could extract short testlets and where we can add new items fitting the existing calibration.

Strategic use of the Internet by small- and medium-sized companies : an exploratory study

NARCIS (Netherlands)

Sadowski, B.M.; Maitland, C.; Dongen, van J.

2002-01-01

The paper investigates the extent to which the adoption of Internet software and services in small- and medium-sized enterprises (SMEs) has been strategic, i.e. based upon the exploitation of the network characteristics of the new technology. Within SMEs, it seems that opportunistic motivations

Innovations in PHWR design, integration of nuclear power stations into power systems and role of small size nuclear power plants in a developing country

International Nuclear Information System (INIS)

Mehta, S.K.; Kakodkar, A.; Balakrishnan, M.R.; Ray, R.N.; Murthy, L.G.K.; Chamany, B.F.; Kati, S.L.

1977-01-01

PHWR concept of thermal reactors has been considered with a view to exploiting the limited resources of natural uranium and keeping in mind the projected nuclear power programme covering fast breeder reactors. Experience in engineering of current PHWR units in India, gradual build up of necessary infrastructure and operational experience with one unit, have helped in building up design and technological capability in the country. The R and D facilities have been so planned that additional data required for the design of bigger reactor units (i.e.500/600 MWe) could be generated with minimal augmentation. Satisfactory operation of a nuclear power station demands certain prerequisites from the connected power system. The grid should have load patterns suitable for base load operation of these stations, should be stiff so far as voltage and frequency fluctuations are concerned and should have high reliability. A typical power grid in this country is characterised by heavy loads during peak hours and very light loads during night. Regional grids are of small size and the few interconnections existing between the regional grids consist of weak tie lines. Amongst all types of the power stations, it is the nuclear system which undergoes maximum strain and economic penalty while operating when connected to such a power system. Consistent with the above, phase installation of small-size power reactor units of about 200 MWe capacity may facilitate setting up of larger unit sizes at a later date. The effect of any possible reduction in the capital cost of a larger unit power station will enable the power station to partially meet the demand of the more productive types of loads. This paper deals with some of the major design changes that are being incorporated in the PHWR type power reactors currently being set up and the research and development back-up required for the purpose. Since the unit sizes of the power reactors presently contemplated are small compared to nuclear

Operational Risk Assessment and Management in Small and Medium-sized Enterprises

Directory of Open Access Journals (Sweden)

Viktorija Stasytytė

2015-07-01

Full Text Available Modern organizations have raised a need to actively and quickly react to the changes in external business environment, as well as in internal processes considering not only the present situation, but also evaluating possible changes and forecasting the future. Enterprise risk assessment and management, which is strongly related with foreseeing the uncertain future, becomes topical not only scientifically, but also practically seeking to reveal new and unique solutions. Operational risk management in small and medium enterprises, creating the largest part of value added in the whole European Union, demands a separate attention and coordinated decisions and means. The objective of the paper – to analyse the process of enterprise risk management in small and medium-sized enterprises, as well as to propose adequate risk management solutions for these companies. After performing a research, it was found out that small and medium enterprises more than big organizations require a risk management strategy and methodology, need to distinguish activity objectives and events influencing them, and they can efficiently apply a risk portfolio method to manage risk. In small and medium enterprises it is recommended to incorporate a risk management system based on COSO ERM model that can be modified depending on company needs and possibilities, turning it into less formal and structured and easily applicable.

The role of small and medium-sized reactors

International Nuclear Information System (INIS)

Kupitz, J.; Mourogov, V.

1999-01-01

The second half of the twentieth century has seen nuclear power evolve from the research and development environment to an industry that supplies 17% of the world's electricity. The past decade, however, has seen stagnation in nuclear power plant construction in the Western industrialized world, slow nuclear power growth in Eastern Europe and expansion only in East Asia. But the turn of the century is potentially a turning-point for nuclear power because of: increasing world energy consumption, with nuclear power's contribution to reducing greenhouse gas emissions, nuclear fuel resources sustainability, and improvements in operation of current nuclear power plants; advanced reactor designs that will improve economics and availability, and further enhance safety; and continued strengthening of the nuclear power safeguards system. This paper looks at the role that small and medium-sized reactors can play in an increasingly competitive global energy market, particularly with regard to maintaining a sustainable mix of energy sources. (author)

Can the business model of Handelsbanken be an archetype for small and medium sized banks? A comparative case study

DEFF Research Database (Denmark)

Kousgaard Larsen, Morten; Lange Nissen, Jacob; Lueg, Rainer

2014-01-01

strengthening of the financial and non-financial position can serve as a blueprint for small- and medium sized banks. We conduct a comparative case study by interviewing Handelsbanken and the disguised ‘Danish Local Bank’ (DLB), where the DLB is a representative example of a small- and medium sized Danish bank......The Danish Banking sector faces increasing requirements regarding regulation and profitability, which especially threatens small- and medium sized banks. This study analyzes whether the successful business model of Handelsbanken (‘The Handelsbanken Way’) to banking in regard to the needed....... This study is structured according to the frameworks from Business Model implementations and from implied organizational structures. Using the notion of Osterwalder and Pigneur (2010), this study reveals only minor differences in the Business Models of Handelsbanken and DLB. Despite the supposedly obvious...

Synthesis and characterization of small size fluorescent LEEH caped blue emission ZnTe quantum dots

Directory of Open Access Journals (Sweden)

Patnaik Sumanta Kumar

2017-04-01

Full Text Available We report here for the first time the synthesis of LEEH caped very small size (2 nm ZnTe quantum dots at low temperature (less than 100 °C using a simple chemical route. The effects of aging and stirring time on the absorption spectra of the quantum dots were investigated. The synthesized nanocrystal (NC was characterized by PL, TEM, XRD and the formation of very small size quantum dots having FCC structure was confirmed. Further, blue emission from the prepared sample was observed during exposure to monochromatic UV radiation. ZnTe NCs obtained in this study were found to be more stable compared to those presented in literature reports. ZnTe NCs may be considered as a new material in place of CdTe for optoelectronics devices.

APLIKASI MOBILE-CUSTOMER RELATIONSHIP MANAGEMENT UNTUK SMALL AND MEDIUM SIZE ENTERPRISES (SMEs

Directory of Open Access Journals (Sweden)

Utaminingsih Linarti

2015-07-01

Full Text Available The key factor of enterprise in order to still growth and developed is customer. The customer will give the value to the enterprise in the form of profit. Therefore, enterprises must be able to establish an sustainable relationship to customer. Since 1990 began to develop what is called Customer Relationship Management (CRM. CRM implements between the development of information technology and customer-centric views. The development of technology and the human need's to move quickly, CRM evolved into a mobile CRM. The Internet make mobile-CRM easily used to all of enterprise, especially small and medium size enterprise. This article is aim to explain the role and the applicability of mobile CRM to business level conditions of small and medium size enterprises (SMEs. The presence of mobile phone operating system that is flexible (android system, the internet cost of affordable and the social media applications as analogy of user interface in making mobile CRM application. CRM mobile application can be downloaded or installed through the app store with ease. It encourages mobile-CRM benefit's rather than as a function of customer data collection but became a window for customer information. In addition, the database can be analysis and relate to customer activity. Mobile CRM applications can take advantage of cross selling methods.

Analyzing the management process in small and medium-sized enterprises in the Region of South Bohemia

Directory of Open Access Journals (Sweden)

Váchal Jan

2017-09-01

Full Text Available The entry is aimed at analyzing the process of managing small and medium-sized enterprise, specifically in the Region of South Bohemia. The testing sample included 180 enterprises. The fundamental statistical information about SMEs is included, focusing of the numbers, the size category, and their specialization in the Region of South Bohemia. The research activities were aimed at the steepness of management structures and at their extent on all management levels. The analysis indicates that micro-enterprises prefer one management level, while small and middle-sized enterprises prefer two management levels with the statistic dependence on the size category. In regard to the number of employees on individual management levels, the top positions have from 6 employees up to 30 on the operative level. The general business trend involves a transfer to the functional management structure. With respect to the strategic management and decision- making, enterprises boost an attractive prospect of mainly their own sources. A statistical correlation was proved between the elaborated strategy, the size of the enterprise and number of management levels. A strong correlation between the number of management levels and the aim of the enterprise i.e. the type of organization structure was not proved.

Reliability of dose volume constraint inference from clinical data

DEFF Research Database (Denmark)

Lutz, C M; Møller, D S; Hoffmann, L

2017-01-01

Dose volume histogram points (DVHPs) frequently serve as dose constraints in radiotherapy treatment planning. An experiment was designed to investigate the reliability of DVHP inference from clinical data for multiple cohort sizes and complication incidence rates. The experimental background...... was radiation pneumonitis in non-small cell lung cancer and the DVHP inference method was based on logistic regression. From 102 NSCLC real-life dose distributions and a postulated DVHP model, an 'ideal' cohort was generated where the most predictive model was equal to the postulated model. A bootstrap...

β-ray scintillation survey meter for small-sized pipes

International Nuclear Information System (INIS)

Yamano, Toshiya; Suzuki, Toshikazu; Yoshida, Yoshiteru; Higashidate, Takamichi; Yonemura, Kenji; Fujita, Michio.

1990-01-01

The outer surface of the small-sized pipes used as scaffolding is measured by beta/gamma survey meter when they are carried out from the controlled area in nuclear facilities. But, the measurement of the radioactive contamination on the inner surface, when it is needed, is done indirectly using the smear method. To improve these vexatious works, Fuji Electric Co., Ltd. and Chubu Electric Power Co., Inc. jointly developed a beta-ray scintillation survey meter which, when inserted directly into pipes, can detect radioactive contamination on the inner surface. This detector is made of cylindrical plastic scintillator and it can measure low energy beta-ray by using the coincidence method which reduces random noise. A field test carried out with this prototype survey meter brought favorable results for designing its final version. (author)

Handling of Environmental Related Requirements : Awareness and Ability to Act at Small and Medium Sized Electric and Electronic Companies

OpenAIRE

Lin, Han-Hsuan

2008-01-01

Environmental related product requirements are increasing worldwide from government authorities, customers and other stakeholders. For small and medium sized companies manufacturing electric and electronic products it is more difficult compared to bigger companies to meet new product related requirements due to smaller budget, resources and knowledge. This research studies the awareness and ability to act upon changes when small and medium sized companies in Sweden face environmental related ...

Exploring the Effects of Brand Promotion and Brand Image Perception on Business Outcomes of Small-sized Agribusiness Firms

Directory of Open Access Journals (Sweden)

Chux Gervase Iwu

2015-01-01

Full Text Available To date there is hardly any empirical evidence in academic literature that branding, particularly brand promotion and brand image perception, plays any significant role in the performance of small-sized agribusiness, especially those in the Sub-Saharan (SSA region. This study was triggered by the need to fill this vacuum. Survey data were collected from small-sized agribusiness firms in one of the SSA economic ‘powerhouses’, which is Nigeria. Employing a contemporary research technique, specifically the Consistent Partial Least Square Structural Equation Modeling (denoted as PLSc, the study found that both brand promotion and brand image perception are instrumental for enhancing the organizational performance of small agribusinesses. In sum, the findings lend empirical support to the extant literature on brand promotion and brand image perception as precursors to the performance of firms regardless of a its size and business location. The implications of study, limitation and future research directions are further highlighted in the concluding section of the paper.

External Determinants of the Development of Small and Medium-Sized Enterprises – Empirical Analysis

Directory of Open Access Journals (Sweden)

Renata Lisowska

2015-01-01

Full Text Available The paper aims to identify external determinants of the development of small and medium-sized enterprises and assess their impact on the functioning of these entities in Poland. Meeting this objective required: identifying determinants of the development of SMEs, determining the current development situation of the surveyed enterprises and examining the impact of external determinants on the development of SMEs. The implementation of the above-presented goals was based on the following assumptions: (i the current situation of the surveyed enterprises is determined with the use of quantitative indicators (turnover volume, number of employees, market share, profit levels (ii the analysis of external determinants encompasses three components of the environment: the macro-environment, the meso-environment and the micro-environment, (iii in each analysed area there are separate analyses conducted for micro, small and medium-sized enterprises, enabling greater precision in the identification of external determinants of development for each category of businesses.

SU-E-T-471: Small Field Jaw/MLC Reference Data

International Nuclear Information System (INIS)

Kerns, J; Alvarez, P; Followill, D; Lowenstein, J; Molineu, A; Summers, P; Kry, S

2014-01-01

Purpose: In recent years the need for small field data of MLCs has increased due to the use of intensity-modulated radiation (IMRT), but moreover the use of stereotactic body radiation (SBRT) has increased, which uses not simply small field sizes, but small jaw and field sizes together. Having reference data for these small fields that is reliable would be invaluable to the physics community. Our study has gathered these values and the data distributions from the Radiological Physics Center's (RPC) site visits between 1990 and the present. Methods: For all measurements, the RPC used a 25 × 25 × 25cm water phantom placed at 100cm SSD. All measurements were made with an Exradin A16 cylindrical ion chamber at an effective depth of 10 cm. A total of 42 Varian machine measurements were used to compose the data for a 6 MV beam and 5 TrueBeam 6 MV flattening filter free (FFF) beams were used for FFF data. Results: Jaw/MLC fields were measured for both 6 MV and 6 MF FFF beams with the jaws and MLCs both at the following field sizes: 6×6, 4×4, 3×3, and 2×2cm. Measurements were normalized to the 10×10 field readings (defined by the jaws and MLC). Spread in the data was minimal and demonstrates a high level of accuracy of acquired data. Conclusion: Small field Jaw/MLC reference data for Varian 6MV and 6 MV FFF beams has been analyzed and presented here, composed of the aggregation of numerous RPC site visits. Obtaining reliable small field data remains difficult, however the RPC has collected high fidelity small field Jaw/MLC data. The data are presented as a reference along with their distributions, in such a way that the physicist can act based upon their own desired agreement with the reference data

Detection of small-size planetary candidates with CoRoT data

Directory of Open Access Journals (Sweden)

Moutou C.

2011-02-01

Full Text Available With the discovery of CoRoT-7b, the first transiting super-Earth, the CoRoT space mission has shown the capability to detect short-period rocky planets around solar-like stars. By performing a blind test with real CoRoT light curves, we want to establish the detection threshold of small-size planets in CoRoT data. We investigate the main obstacles to the detection of transiting super-Earths in CoRoT data, notably the presence of short-time scale variability and hot pixels.

The Relationship Between Training and Employment Growth in Small and Medium-Sized Enterprises

OpenAIRE

Andy Cosh; Alan Hughes; Melvyn Weeks

2000-01-01

This paper provides a rigorous analysis of the impact of training upon the employment growth characteristics of small and medium sized firms. Using appropriate statistical techniques to cope with sample selection biases and heterogenerous employment growth patterns it reveals that training is positively related to employment growth, in particular when it is embedded in a wider range of human relations practices.

SU-E-T-611: Effective Treatment Volume of the Small Size IORT Applicators

International Nuclear Information System (INIS)

Krechetov, A.S.; Goer, D.A.

2014-01-01

Purpose Mobile electron linear accelerators are gaining more attention recently, providing a lower cost and simpler way to perform intraoperative treatment. However, the simplicity of the treatment process does not eliminate the need for proper attention to the technical aspects of the treatment. One of the potential pitfalls is incorrect selection of the appropriate applicator size to adequately cover the tumor bed to the prescription dose. When treating tumor beds in the pelvis, the largest applicator that fits into the pelvis is usually selected as there is concern about microscopic extension of the disease along the sidewalls of the pelvis. But when treating early stage breast tumors, there is a natural tendency to select an applicator as small as possible so as not to jeopardize cosmesis. Methods This investigation questions how much of the typical breast treatment volume gets adequate exposure and what is the correct strategy in selecting the proper applicator size. Actual data from isodose scans were analyzed. Results We found that typical treatment dose prescriptions can cover as much as 80% and as little as 20% of the nominal treatment volume depending on the applicator size and energy of the beam and whether the dose is prescribed to the 80 or 90% isodose level. Treatment volume is defined as a cylinder with diameter equal to applicator and height equal to the corresponding D80 or D90 depth. Conclusion If mobile linear accelerators are used, there can be significant amount of “cold volume” depending on the applicator size and this should be taken into account when selecting the applicator that is needed. Using too small of an applicator could result in significant under-dosing to the tissue at risk. Long-term clinical data demonstrates that selecting an adequate field size results in good ontological control as well as excellent cosmesis. Intraop Medical Corp was providing facilities and equipment for this research

Small size ion pumps

International Nuclear Information System (INIS)

Cyranski, R.; Kiliszek, Cz.R.; Marks, J.; Sobolewski, A.; Magielko, H.

2001-01-01

This paper describes some designs of the two versions ion pumps and their range operation for various magnetic fields. The first version is made with different cell size in the anode element and titanium cathode operating in magnetic field from 600 to 650 Gs and the second version with the same anode element but differential Ti/Ta cathode working in magnetic field above 1200 Gs

Small-angle X-ray scattering (SAXS) for metrological size determination of nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Gleber, Gudrun; Krumrey, Michael; Cibik, Levent; Marggraf, Stefanie; Mueller, Peter [Physikalisch-Technische Bundesanstalt, Abbestr. 2-12, 10587 Berlin (Germany); Hoell, Armin [Helmholtz-Zentrum Berlin, Albert-Einstein-Str. 15, 12489 Berlin (Germany)

2011-07-01

To measure the size of nanoparticles, different measurement methods are available but their results are often not compatible. In the framework of an European metrology project we use Small-Angle X-ray Scattering (SAXS) to determine the size and size distribution of nanoparticles in aqueous solution, where the special challange is the traceability of the results. The experiments were performed at the Four-Crystal Monochromator (FCM) beamline in the laboratory of Physikalisch-Technische Bundesanstalt (PTB) at BESSY II using the SAXS setup of the Helmholtz-Zentrum Berlin (HZB). We measured different particles made of PMMA and gold in a diameter range of 200 nm down to about 10 nm. The aspects of traceability can be classified in two parts: the first is the experimental part with the uncertainties of distances, angles, and wavelength, the second is the part of analysis, with the uncertainty of the choice of the model used for fitting the data. In this talk we want to show the degree of uncertainty, which we reached in this work yet.

Validity and reliability of transbronchial needle aspiration for diagnosing mediastinal adenopathies

Directory of Open Access Journals (Sweden)

González Ana

2010-04-01

Full Text Available Abstract Background The aim is to assess the validity and reliability of transbronchial needle aspiration (TBNA of mediastinal and hilar adenopathies and to evaluate factors predictive of TBNA outcome. Methods We performed an analysis of prospectively collected data of patients (n = 580 who underwent TBNA (n = 685 from January 1998 to December 2007 in our center. Validity and reliability were evaluated for the overall sample and according to specific pathology. Factors predicting the successful acquisition of diagnostic samples were analyzed by multivariate analysis. Results Overall sensitivity, specificity, accuracy, and positive and negative predictive (NPV values for TBNA were 68%, 100%, 68.8%, 100%, and 10%, respectively. The most sensitive and accurate TBNAs were obtained for patients with small cell lung carcinoma and the worst results were for patients with lymphomas. NPV were similar for all pathologies. The most predictive factors of outcome were adenopathy size and the presence of indirect signs at the puncture site. Conclusion The sensitivity and accuracy of TBNA are high in small cell lung cancer, followed by other types of carcinoma, sarcoidosis, and tuberculosis, and low for lymphoproliferative diseases. The NPV of TBNA for all individual pathologies is low. The size of the adenopathy and the presence of indirect signs at the puncture site predict the achievement of diagnostic samples.

Optimal chest drain size: the rise of the small-bore pleural catheter.

Science.gov (United States)

Fysh, Edward T H; Smith, Nicola A; Lee, Y C Gary

2010-12-01

Drainage of the pleural space is not a modern concept, but the optimal size of chest drains to use remains debated. Conventional teaching advocates blunt dissection and large-bore tubes; but in recent years, small-bore catheters have gained popularity. In the absence of high-quality randomized data, this review summarizes the available literature on the choice of chest drains. The objective data supporting the use of large-bore tubes is scarce in most pleural diseases. Increasing evidence shows that small-bore catheters induce less pain and are of comparable efficacy to large-bore tubes, including in the management of pleural infection, malignant effusion, and pneumothoraces. The onus now is on those who favor large tubes to produce clinical data to justify the more invasive approach. © Thieme Medical Publishers.

Implementation of Lean Six Sigma in small- and medium-sized manufacturing enterprises in the Netherlands

NARCIS (Netherlands)

Timans, W.; Antony, J.; Ahaus, K.; van Solingen, R.

In this paper we provide an exploration and analysis of Lean Six Sigma (LSS) implementation in Dutch manufacturing/engineering small- and medium-sized enterprises (SMEs). Critical success factors (CSFs) and impeding factors are identified and analysed. Exploratory empirical evidence about LSS

Reliable critical sized defect rodent model for cleft palate research.

Science.gov (United States)

Mostafa, Nesrine Z; Doschak, Michael R; Major, Paul W; Talwar, Reena

2014-12-01

Suitable animal models are necessary to test the efficacy of new bone grafting therapies in cleft palate surgery. Rodent models of cleft palate are available but have limitations. This study compared and modified mid-palate cleft (MPC) and alveolar cleft (AC) models to determine the most reliable and reproducible model for bone grafting studies. Published MPC model (9 × 5 × 3 mm(3)) lacked sufficient information for tested rats. Our initial studies utilizing AC model (7 × 4 × 3 mm(3)) in 8 and 16 weeks old Sprague Dawley (SD) rats revealed injury to adjacent structures. After comparing anteroposterior and transverse maxillary dimensions in 16 weeks old SD and Wistar rats, virtual planning was performed to modify MPC and AC defects dimensions, taking the adjacent structures into consideration. Modified MPC (7 × 2.5 × 1 mm(3)) and AC (5 × 2.5 × 1 mm(3)) defects were employed in 16 weeks old Wistar rats and healing was monitored by micro-computed tomography and histology. Maxillary dimensions in SD and Wistar rats were not significantly different. Preoperative virtual planning enhanced postoperative surgical outcomes. Bone healing occurred at defect margin leaving central bone void confirming the critical size nature of the modified MPC and AC defects. Presented modifications for MPC and AC models created clinically relevant and reproducible defects. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Evaluation of Approaches to Analyzing Continuous Correlated Eye Data When Sample Size Is Small.

Science.gov (United States)

Huang, Jing; Huang, Jiayan; Chen, Yong; Ying, Gui-Shuang

2018-02-01

To evaluate the performance of commonly used statistical methods for analyzing continuous correlated eye data when sample size is small. We simulated correlated continuous data from two designs: (1) two eyes of a subject in two comparison groups; (2) two eyes of a subject in the same comparison group, under various sample size (5-50), inter-eye correlation (0-0.75) and effect size (0-0.8). Simulated data were analyzed using paired t-test, two sample t-test, Wald test and score test using the generalized estimating equations (GEE) and F-test using linear mixed effects model (LMM). We compared type I error rates and statistical powers, and demonstrated analysis approaches through analyzing two real datasets. In design 1, paired t-test and LMM perform better than GEE, with nominal type 1 error rate and higher statistical power. In design 2, no test performs uniformly well: two sample t-test (average of two eyes or a random eye) achieves better control of type I error but yields lower statistical power. In both designs, the GEE Wald test inflates type I error rate and GEE score test has lower power. When sample size is small, some commonly used statistical methods do not perform well. Paired t-test and LMM perform best when two eyes of a subject are in two different comparison groups, and t-test using the average of two eyes performs best when the two eyes are in the same comparison group. When selecting the appropriate analysis approach the study design should be considered.

Iterative CT reconstruction with small pixel size: distance-driven forward projector versus Joseph's

Science.gov (United States)

Hahn, K.; Rassner, U.; Davidson, H. C.; Schöndube, H.; Stierstorfer, K.; Hornegger, J.; Noo, F.

2015-03-01

Over the last few years, iterative reconstruction methods have become an important research topic in x-ray CT imaging. This effort is motivated by increasing evidence that such methods may enable significant savings in terms of dose imparted to the patient. Conceptually, iterative reconstruction methods involve two important ingredients: the statistical model, which includes the forward projector, and a priori information in the image domain, which is expressed using a regularizer. Most often, the image pixel size is chosen to be equal (or close) to the detector pixel size (at field-of-view center). However, there are applications for which a smaller pixel size is desired. In this investigation, we focus on reconstruction with a pixel size that is twice smaller than the detector pixel size. Using such a small pixel size implies a large increase in computational effort when using the distance-driven method for forward projection, which models the detector size. On the other hand, the more efficient method of Joseph will create imbalances in the reconstruction of each pixel, in the sense that there will be large differences in the way each projection contributes to the pixels. The purpose of this work is to evaluate the impact of these imbalances on image quality in comparison with utilization of the distance-driven method. The evaluation involves computational effort, bias and noise metrics, and LROC analysis using human observers. The results show that Joseph's method largely remains attractive.

Local governments and climate change: sustainable energy planning and implementation in small and medium sized communities

National Research Council Canada - National Science Library

Van Staden, Maryke; Musco, Francesco

2010-01-01

The focus of 'Local governments and climate change' is on how small and medium-sized communities in Europe are effectively responding to climate change, with a particular focus on different approaches...

Improved Reliability of Small Molecule Organic Solar Cells by Double Anode Buffer Layers

Directory of Open Access Journals (Sweden)

Pao-Hsun Huang

2014-01-01

Full Text Available An optimized hybrid planar heterojunction (PHJ of small molecule organic solar cells (SM-OSCs based on copper phthalocyanine (CuPc as donor and fullerene (C60 as acceptor was fabricated, which obviously enhanced the performance of device by sequentially using both MoO3 and pentacene as double anode buffer layers (ABL, also known as hole extraction layer (HEL. A series of the vacuum-deposited ABL, acting as an electron and exciton blocking layer, were examined for their characteristics in SM-OSCs. The performance and reliability were compared between conventional ITO/ABL/CuPc/C60/BCP/Ag cells and the new ITO/double ABL/CuPc/C60/BCP/Ag cells. The effect on the electrical properties of these materials was also investigated to obtain the optimal thickness of ABL. The comparison shows that the modified cell has an enhanced reliability compared to traditional cells. The improvement of lifetime was attributed to the idea of double layers to prevent humidity and oxygen from diffusing into the active layer. We demonstrated that the interfacial extraction layers are necessary to avoid degradation of device. That is to say, in normal temperature and pressure, a new avenue for the device within double buffer layers has exhibited the highest values of open circuit voltage (Voc, fill factor (FF, and lifetime in this work compared to monolayer of ABL.

Spatial and temporal variation of body size among early Homo.

Science.gov (United States)

Will, Manuel; Stock, Jay T

2015-05-01

The estimation of body size among the earliest members of the genus Homo (2.4-1.5Myr [millions of years ago]) is central to interpretations of their biology. It is widely accepted that Homo ergaster possessed increased body size compared with Homo habilis and Homo rudolfensis, and that this may have been a factor involved with the dispersal of Homo out of Africa. The study of taxonomic differences in body size, however, is problematic. Postcranial remains are rarely associated with craniodental fossils, and taxonomic attributions frequently rest upon the size of skeletal elements. Previous body size estimates have been based upon well-preserved specimens with a more reliable species assessment. Since these samples are small (n Koobi Fora after 1.7Myr, indicating regional size variation. The significant body size differences between specimens from Koobi Fora and Olduvai support the cranial evidence for at least two co-existing morphotypes in the Early Pleistocene of eastern Africa. Copyright © 2015 Elsevier Ltd. All rights reserved.

Small metal soft tissue foreign body extraction by using 3D CT guidance: A reliable method

International Nuclear Information System (INIS)

Tao, Kai; Xu, Sen; Liu, Xiao-yan; Liang, Jiu-long; Qiu, Tao; Tan, Jia-nan; Che, Jian-hua; Wang, Zi-hua

2012-01-01

Objective: To introduce a useful and accurate technique for the locating and removal of small metal foreign bodies in the soft tissues. Methods: Eight patients presented with suspected small metal foreign bodies retained in the soft tissues of various body districts. Under local anesthesia, 3–6 pieces of 5 ml syringe needles or 1 ml syringe needles were induced through three different planes around the entry point of the foreign bodies. Using these finders, the small metal FBs were confirmed under 3D CT guidance. Based on the CT findings, the soft tissues were dissected along the path of the closest needle and the FBs were easily found and removed according to the relation with the closest needle finder. Results: Eight metal foreign bodies (3 slices, 3 nails, 1 fish hook, 1 needlepoint) were successfully removed under 3D CT guidance in all patients. The procedures took between 35 min and 50 min and the operation times took between 15 min and 25 min. No complications arose after the treatment. Conclusion: 3D CT-guided technique is a good alternative for the removal of small metal foreign body retained in the soft tissues as it is relatively accurate, reliable, quick, carries a low risk of complications and can be a first-choice procedure for the extraction of small metal foreign body.

Small, medium, large or supersize? The development and evaluation of interventions targeted at portion size

Science.gov (United States)

Vermeer, W M; Steenhuis, I H M; Poelman, M P

2014-01-01

In the past decades, portion sizes of high-caloric foods and drinks have increased and can be considered an important environmental obesogenic factor. This paper describes a research project in which the feasibility and effectiveness of environmental interventions targeted at portion size was evaluated. The studies that we conducted revealed that portion size labeling, offering a larger variety of portion sizes, and proportional pricing (that is, a comparable price per unit regardless of the size) were considered feasible to implement according to both consumers and point-of-purchase representatives. Studies into the effectiveness of these interventions demonstrated that the impact of portion size labeling on the (intended) consumption of soft drinks was, at most, modest. Furthermore, the introduction of smaller portion sizes of hot meals in worksite cafeterias in addition to the existing size stimulated a moderate number of consumers to replace their large meals by a small meal. Elaborating on these findings, we advocate further research into communication and marketing strategies related to portion size interventions; the development of environmental portion size interventions as well as educational interventions that improve people's ability to deal with a ‘super-sized' environment; the implementation of regulation with respect to portion size labeling, and the use of nudges to stimulate consumers to select healthier portion sizes. PMID:25033959

Development of a small-sized radon data logger

International Nuclear Information System (INIS)

Tasaka, Shigeki; Sasaki, Yoshimi

1996-01-01

A small-sized radon data logger and a electrostatic collecting radon monitor were developed for the continuous monitoring of environmental radon and radon daughters. A PIN photodiode (PD), an alpha particle defector, installed inside a container attracts radon daughters when charged electrostatically. Alpha particles are completely separated from each other according to the energy level. New logger has made it possible 10 analysts and save the radon data. Alpha particle count data from radon daughters are automatically integrated over preset time intervals and the energy regions. The desiccant P 2 O 5 was placed in the bottom of the monitor, since the collection efficiency of 218 Po atoms depends on the humidity of the air. We can get the 30 days continuous data logging at 30 min sampling frequency at any place with the car battery. We observed the radon concentration of the air inside the Super-Kamiokande dome from Jan-30 to Feb-8-1996. The average of radon concentration was found to be (46±13) Bq/m 3 . (author)

Determinants of capital structure in small and medium sized enterprises in Malaysia

OpenAIRE

Mat Nawi, Hafizah

2015-01-01

This thesis was submitted for the award of Doctor of Philosophy and was awarded by Brunel University London This study aims to investigate the determinants of capital structure in small and medium-sized enterprises (SMEs) in Malaysia and their effect on firms’ performance. The study addresses the following primary question: What are the factors that influence the capital structure of SMEs in Malaysia? The sample of this research is SMEs in the east coast region of Malaysia. Adopting a posi...

THE RELATIONSHIP BETWEEN SMALL AND MEDIUM-SIZED ENTERPRISES, TOURISM AND ECONOMIC DEVELOPMENT

Directory of Open Access Journals (Sweden)

Tatjana Dimoska

2015-01-01

Full Text Available Tourism is the world’s largest industry and makes a major contribution to the economies of most developed and developing countries. Tourism as an important socio-economical phenomenon is characterized with distinctly largeness and dynamic development that results with many positive direct as well as indirect economical effects. That is a measure for increasing of possibilities of encouragement of the total economical development through tourism development. Tourism generates income from consumption of goods and services by tourists as well as taxes on businesses in the tourism industry, provides employment in services related to tourism, but also creates jobs in the tertiary sector, generates growth of primary and secondary sectors of the industry as result of multiplicative effect. In this context especially are important small and medium tourism enterprises which dominate in the tourism destinations according to their number, originating a variety of benefits for the tourism destinations by providing direct contact with tourists and by encouraging tourist for spending in a local community. The aim of this paper is to point out the importance of small and medium –sized enterprises in general and especially in the field of tourism for increasing economic development in the national economy with particular reference on the territory of the Republic of Macedonia. In this paper, first will be analyzed the term small and medium - sized enterprises in general and then will be explained their application in the field of tourism with highlighting of their strategic advantages for the tourism destinations and overall economic development of the entire national economy. Finally, will be analyzed the role played by SMEs for the economic development of the Republic of Macedonia with a special emphasis on the measures and actions which have to be taken in the future by the competent authorities for further stimulation of their development.

An Agile Methodology for Implementing Service-Oriented Architecture in Small and Medium Sized Organizations

Science.gov (United States)

Laidlaw, Gregory

2013-01-01

The purpose of this study is to evaluate the use of Lean/Agile principles, using action research to develop and deploy new technology for Small and Medium sized enterprises. The research case was conducted at the Lapeer County Sheriff's Department and involves the initial deployment of a Service Oriented Architecture to alleviate the data…

Radiation-related small head sizes among prenatally exposed atomic bomb survivors

International Nuclear Information System (INIS)

Otaki, Masanori; Schull, William J.

2004-01-01

severely mentally retarded cases with small heads and 68.9 and 11.9 for the severely mentally retarded cases without small heads. These values are 96.4 and 19.8 for cases with small heads only. The mean IQ and standard deviation for the overall sample are 107.8 and 16.4, respectively. No significant difference exists between the first two IQ means identified above, but both are significantly less than the mean for individuals with small heads but without severe mental retardation. The mean IQ of individuals with small heads but without severe mental retardation does not differ significantly from the mean for the entire sample. The relationship of small head size to four other anthropometric measurements (standing height, body weight, sitting height, and chest circumference) is described. (author)

Quantum-dot size and thin-film dielectric constant: precision measurement and disparity with simple models.

Science.gov (United States)

Grinolds, Darcy D W; Brown, Patrick R; Harris, Daniel K; Bulovic, Vladimir; Bawendi, Moungi G

2015-01-14

We study the dielectric constant of lead sulfide quantum dot (QD) films as a function of the volume fraction of QDs by varying the QD size and keeping the ligand constant. We create a reliable QD sizing curve using small-angle X-ray scattering (SAXS), thin-film SAXS to extract a pair-distribution function for QD spacing, and a stacked-capacitor geometry to measure the capacitance of the thin film. Our data support a reduced dielectric constant in nanoparticles.

Preparing the Production of a New Product in Small and Medium-Sized Enterprises by Using the Method of Projects Management

Science.gov (United States)

Bijańska, Jolanta; Wodarski, Krzysztof; Wójcik, Janusz

2016-06-01

Efficient and effective preparation the production of new products is important requirement for a functioning and development of small and medium-sized enterprises. One of the methods, which support the fulfilment of this condition is project management. This publication presents the results of considerations, which are aimed at developing a project management model of preparation the production of a new product, adopted to specificity of small and medium-sized enterprises.

Meeting increased logistical demands : Developing as a small- and medium-sized system supplier

OpenAIRE

Carlsson, Inga-Lill

2009-01-01

Many subcontractors choose to implement a strategy of “system supply” in order to meetincreasing global competition. They are then confronted with increased demands to take agreater overall responsibility in this role. It is important to investigate the implications of theseresponsibilities before investing in developing the organization, especially for a small- ormedium-sized subcontractor with limited resources. The customer’s view of different demandsdoes not necessarily correspond to how ...

Ultracapacitors for fuel saving in small size hybrid vehicles

Energy Technology Data Exchange (ETDEWEB)

Solero, L.; Lidozzi, A.; Serrao, V. [University ROMA TRE, Dept. of Mechanical and Industrial Eng., Via della Vasca Navale, 79 - 00146 Roma (Italy); Martellucci, L. [University of Rome ' ' La Sapienza' ' , Dept. of Electrical Eng., Via Eudossiana, 18 - 00184 Roma (Italy); Rossi, E. [ENEA, Via Anguillarese, 301 - 00060 S. Maria Galeria, Roma (Italy)

2011-01-01

The main purpose of the paper is to describe a small size hybrid vehicle having ultracapacitors as on-board storage unit. The vehicle on-board main power supply is achieved by a genset being formed of a 250 cm{sup 3} internal combustion engine and a permanent magnet synchronous electric generator, whereas 4 16V-500F ultracapacitors modules are connected in series in order to supply as well as to store the power peaks during respectively acceleration and braking vehicle modes of operation. The traction power is provided by a permanent magnet synchronous electric motor, whereas a distributed power electronic interface is in charge of all the required electronic conversions as well of controlling the operating conditions for each power unit. The paper discusses the implemented control strategy and shows experimental results on the modes of operation of both generation unit and storage unit. (author)

Small and medium sized enterprises (SMEs and transfer pricing

Directory of Open Access Journals (Sweden)

Veronika Solilová

2012-01-01

Full Text Available Small and medium sized enterprises have very important position in the EU economy, mainly in the area of growth and employment. However, most of SMEs are active only in their home country and only a few of them participate in cross-border activities. Furthermore, their activities in the internal market are limited by great deal of obstacles, mainly in the form of different tax systems which generate excessive compliance costs of taxation and the existence of different SMEs definitions for various purposes in Member states. In addition, from the view of the international taxation issues, the most important obstacles can be considered a transfer pricing and cross-border loss compensations. In this area, SMEs are facing specific problems and have specific needs. The aim of the paper is to analyze and evaluate the specific transfer pricing issues of SMEs and propose recommendations for them.

Competitive intelligence tools used by small and medium-sized enterprises

Directory of Open Access Journals (Sweden)

Tshilidzi Eric Nenzhelele

2015-08-01

Full Text Available Small and Medium-sized Enterprises (SMEs contribute highly to the gross domestic product, reduction in unemployment, wealth creation and improvement in the quality of life. Due to technology and globalisation, SMEs now compete with enterprises beyond the borders of their country. To survive in this global competitive business environment, SMEs seek for tools that offer competitive advantage. Competitive Intelligence (CI provides competitive advantage to enterprises that practice it. While CI practice has been widely research for larger enterprises, there is lack of research on CI practice pertaining to SMEs. This research establishes tools used by SMEs in CI practice. The research was quantitative in nature and a self-administered questionnaire was used to collected data from owners/managers of SMEs

Irradiation test of component for radiation-resistant small sized motor

International Nuclear Information System (INIS)

Nakamichi, M.; Ishitsuka, E.; Shimakawa, S.; Kan, S.

2009-01-01

A small-sized motor with a resistance to radiation was developed. This motor has been able to operate at a gamma-ray dose of a value 700 times as high as the specification of a commercial motor. The present work describes results of post-irradiation examinations (PIEs) to evaluate effects of neutron irradiation on the lifetime of some major components of the motor such as a bearing, a magnet and a fixation agent for a field coil wire. It became clear from the results of PIEs that the radiation-resistance dose of the motor using a Sm-Co magnet will be expected to be one order of magnitude higher than that of the motor using a Nb-Fe-B magnet.

Quenching effect in an optical fiber type small size dosimeter irradiated with 290 MeV·u{sup -1} carbon ions

Energy Technology Data Exchange (ETDEWEB)

Hirata, Yuho; Watanabe, Kenichi; Uritani, Akira; Yamazaki, Atsushi [Graduate School of Engineering, Nagoya University, Nagoya (Japan); Koba, Yusuke; Matsufuji, Naruhiro [National Institute of Radiological Sciences, Chiba (Japan)

2016-09-15

We are developing a small size dosimeter for dose estimation in particle therapies. The developed dosimeter is an optical fiber based dosimeter mounting an radiation induced luminescence material, such as an OSL or a scintillator, at a tip. These materials generally suffer from the quenching effect under high LET particle irradiation. We fabricated two types of the small size dosimeters. They used an OSL material Eu:BaFBr and a BGO scintillator. Carbon ions were irradiated into the fabricated dosimeters at Heavy Ion Medical Accelerator in Chiba (HIMAC). The small size dosimeters were set behind the water equivalent acrylic phantom. Bragg peak was observed by changing the phantom thickness. An ion chamber was also placed near the small size dosimeters as a reference. Eu:BaFBr and BGO dosimeters showed a Bragg peak at the same thickness as the ion chamber. Under high LET particle irradiation, the response of the luminescence-based small size dosimeters deteriorated compared with that of the ion chamber due to the quenching effect. We confirmed the luminescence efficiency of Eu:BaFBr and BGO decrease with the LET. The reduction coefficient of luminescence efficiency was different between the BGO and the Eu:BaFBr. The LET can be determined from the luminescence ratio between Eu:BaFBr and BGO, and the dosimeter response can be corrected. We evaluated the LET dependence of the luminescence efficiency of the BGO and Eu:BaFBr as the quenching effect. We propose and discuss the correction of the quenching effect using the signal intensity ratio of the both materials. Although the correction precision is not sufficient, feasibility of the proposed correction method is proved through basic experiments.

Performance evaluation of a mouse-sized camera for dynamic studies in small animals

International Nuclear Information System (INIS)

Loudos, George; Majewski, Stan; Wojcik, Randy; Weisenberger, Andrew; Sakellios, Nicolas; Nikita, Konstantina; Uzunoglu, Nikolaos; Bouziotis, Penelope; Varvarigou, Alexandra

2007-01-01

A mouse sized camera has been built in terms of collaboration between the presenting institutions. The system is used for the performance of dynamic studies in small animals, in order to evaluate novel radiopharmaceuticals. The active area of the detector is approximately 48x96 mm allowing depiction of the entire mouse in a single view. The system is based on two flat-panel Hamamatsu H8500 position sensitive photomultiplier tubes (PSPMT), a pixellated NaI(Tl) scintillator and a copper-beryllium (CuBe) parallel-hole collimator. In this work, the evaluation results of the system are presented, using phantoms and small animals injected with conventional radiophrmaceuticals. Average resolution was ∼1.6 mm on the collimator surface and increased to ∼4.1 mm in 12 cm distance from the detector. The average energy resolution was measured and found to be ∼15.6% for Tc 99m . Results from imaging thin capillaries demonstrated system's high resolution and sensitivity in activity variations was shown. Initial dynamic studies have been carried out in small animals injected with Tc 99m -DTPA and Tc 99m -MDP. The results show system's ability to perform kinetic imaging in small animals

Anomalous size effect in conductivity of Bi films of small thickness

International Nuclear Information System (INIS)

Anopchenko, A.S.; Kashirin, V.Yu.; Komnik, Yu.F.

1995-01-01

Experimental data are obtained at helium temperature, which describe the kinetic properties (conductivity, magnetoresistance and Hall coefficient) of Bi films whose thicknesses are within 100-500 A. The small-thickness Bi films display an anomalous size effect- the growing conductivity at decreasing thickness, and pronounced quantum interference effects - weak electron localization and enhancing electron-electron interaction in a disordered system. The information derived on the kinetic properties of the films is used to identify the character of the changes in the electron and hole concentrations and mobilities with a decreasing thickness. The isotropy of the properties in the films plane due to the axial texture has permitted us to use the equations for a conductor with two types of charge carriers. The used kinetic characteristics correctly take into account the contribution of the quantum corrections related to quantum interference. It is found that the concentration of the charge carries increases appreciably (by about two orders of magnitude) as the film thickness decreases to 100 A, which determines the anomalous size effect in the conductivity of the films

Possible Future Role of Small and Medium Sized Reactors (SMRs) in Countries with Small and Medium Electricity Grids

International Nuclear Information System (INIS)

Alujevic, L.

2016-01-01

Small and Medium Sized Reactors (SMRs) could have enormous potential as options for enhancing the energy supply security, as well as providing a lower capital investment compared to conventional Nuclear Power Plants (NPPs). The trend in SMR development has been towards design certification of small modular reactors, defined as advanced reactors that produce electric power up to 300 MW(e), designed to be built in factories and shipped to utilities for installation as demand arises. The factory-built small modular reactors aim to reduce lengthy construction times while simultaneously increasing quality, thereby minimizing the costs associated with the current time for construction that spans 5 to 8 years. SMR designs include water-cooled reactors, high temperature gas cooled reactors, as well as liquid metal cooled reactors with fast neutron spectrum. Also, many are designed to be emplaced below ground level, giving a high resistance to terrorist threats. The projected timelines of readiness for deployment of SMRs generally range from the present to 2025 - 2030. Currently there are more than 45 SMR designs under development for different application issues. This paper will try to elaborate the benefits and drawbacks of SMRs, as well as describe a couple of designs. Furthermore, some timelines and cost estimates will be provided, depending on the data currently available. Taking all that into account, the conclusion will try to ascertain the suitability of SMRs for Countries with Small and Medium Electricity Grids, namely Croatia. (author).

The reliability of commonly used electrophysiology measures.

Science.gov (United States)

Brown, K E; Lohse, K R; Mayer, I M S; Strigaro, G; Desikan, M; Casula, E P; Meunier, S; Popa, T; Lamy, J-C; Odish, O; Leavitt, B R; Durr, A; Roos, R A C; Tabrizi, S J; Rothwell, J C; Boyd, L A; Orth, M

Electrophysiological measures can help understand brain function both in healthy individuals and in the context of a disease. Given the amount of information that can be extracted from these measures and their frequent use, it is essential to know more about their inherent reliability. To understand the reliability of electrophysiology measures in healthy individuals. We hypothesized that measures of threshold and latency would be the most reliable and least susceptible to methodological differences between study sites. Somatosensory evoked potentials from 112 control participants; long-latency reflexes, transcranial magnetic stimulation with resting and active motor thresholds, motor evoked potential latencies, input/output curves, and short-latency sensory afferent inhibition and facilitation from 84 controls were collected at 3 visits over 24 months at 4 Track-On HD study sites. Reliability was assessed using intra-class correlation coefficients for absolute agreement, and the effects of reliability on statistical power are demonstrated for different sample sizes and study designs. Measures quantifying latencies, thresholds, and evoked responses at high stimulator intensities had the highest reliability, and required the smallest sample sizes to adequately power a study. Very few between-site differences were detected. Reliability and susceptibility to between-site differences should be evaluated for electrophysiological measures before including them in study designs. Levels of reliability vary substantially across electrophysiological measures, though there are few between-site differences. To address this, reliability should be used in conjunction with theoretical calculations to inform sample size and ensure studies are adequately powered to detect true change in measures of interest. Copyright © 2017 Elsevier Inc. All rights reserved.

Analyzing the reliability of shuffle-exchange networks using reliability block diagrams

International Nuclear Information System (INIS)

Bistouni, Fathollah; Jahanshahi, Mohsen

2014-01-01

Supercomputers and multi-processor systems are comprised of thousands of processors that need to communicate in an efficient way. One reasonable solution would be the utilization of multistage interconnection networks (MINs), where the challenge is to analyze the reliability of such networks. One of the methods to increase the reliability and fault-tolerance of the MINs is use of various switching stages. Therefore, recently, the reliability of one of the most common MINs namely shuffle-exchange network (SEN) has been evaluated through the investigation on the impact of increasing the number of switching stage. Also, it is concluded that the reliability of SEN with one additional stage (SEN+) is better than SEN or SEN with two additional stages (SEN+2), even so, the reliability of SEN is better compared to SEN with two additional stages (SEN+2). Here we re-evaluate the reliability of these networks where the results of the terminal, broadcast, and network reliability analysis demonstrate that SEN+ and SEN+2 continuously outperform SEN and are very alike in terms of reliability. - Highlights: • The impact of increasing the number of stages on reliability of MINs is investigated. • The RBD method as an accurate method is used for the reliability analysis of MINs. • Complex series–parallel RBDs are used to determine the reliability of the MINs. • All measures of the reliability (i.e. terminal, broadcast, and network reliability) are analyzed. • All reliability equations will be calculated for different size N×N

Small and medium size nuclear reactors

International Nuclear Information System (INIS)

Al-Mugrabi, M.A.

1996-01-01

The purpose of this appendix is to provide up-to-date technical information relevant to the deployment of small and medium reactors (SMRs). It summarizes the status of SMRs and discusses areas of relevance to their utilization, including seawater desalination; and in particular their simplicity, their flexibility for a variety of applications and the use of passive safety features as fundamental to most of these designs. In response to important commercial developments, the energy range of small and medium reactors is now taken as being up to around 700 MW(e). Detailed information on SMR designs can be found in the IAEA report on The Design and Development Status of Small and Medium Reactor Systems 1995. 5 refs, 2 figs, 1 tab

Wrist and Hand Ultrasound: Reliability of Side-to-Side Comparisons of Very Small (Structures.

Science.gov (United States)

Rossi, Federica; Romano, Nicola; Muda, Alessandro; Martinoli, Carlo; Tagliafico, Alberto

2018-04-24

In ultrasound (US) examinations of clinically relevant very small structures of the wrist and hand, the healthy contralateral side can be used as a reference to identify subtle abnormalities. Intraindividual side-to-side variability must be minimal. The aim of this study was to assess the reliability of side-to-side US evaluations of very small structures of the wrist and hand. Forty-one healthy volunteers were prospectively studied. Small structures of the wrist and hand were evaluated bilaterally by 2 musculoskeletal radiologists in separate sessions. The first annular pulleys of the second finger and the thumb, sagittal band of the third finger, extensor and flexor retinacula, ulnar collateral ligament of the thumb, radial collateral ligament of the second finger, and palmar cutaneous branches of the median and ulnar nerves were considered. To assess intra- and inter-reader agreement, 10 of 41 (24%) examinations were repeated. Nonparametric statistics were used. Data were not normally distributed (P > .001). Intra-reader agreement was κ = 0.674 (95% confidence interval [CI], 0.57-0.78), and inter-reader agreement was κ = 0.935 (95% CI, 0.92-0.95). The mean value ± SD for all of the structures was 0.78 ± 0.44 mm. The overall coefficient of variation was 9.8% ± 0.07%. The intraclass correlation coefficient was 0.97 (95% CI, 0.96-0.98). In clinical practice, the healthy contralateral side can be used as a reference during a real-time musculoskeletal US evaluation of small (structures. © 2018 by the American Institute of Ultrasound in Medicine.

Small angle neutron scattering study of nano sized microstructure in Fe-Cr ODS steels for gen IV in-core applications.

Science.gov (United States)

Han, Young-Soo; Mao, Xiadong; Jang, Jinsung

2013-11-01

The nano-sized microstructures in Fe-Cr oxide dispersion strengthened steel for Gen IV in-core applications were studied using small angle neutron scattering. The oxide dispersion strengthened steel was manufactured through hot isostatic pressing with various chemical compositions and fabrication conditions. Small angle neutron scattering experiments were performed using a 40 m small angle neutron scattering instrument at HANARO. Nano sized microstructures, namely, yttrium oxides and Cr-oxides were quantitatively analyzed by small angle neutron scattering. The yttrium oxides and Cr-oxides were also observed by transmission electron microscopy. The microstructural analysis results from small angle neutron scattering were compared with those obtained by transmission electron microscopy. The effects of the chemical compositions and fabrication conditions on the microstructure were investigated in relation to the quantitative microstructural analysis results obtained by small angle neutron scattering. The volume fraction of Y-oxide increases after fabrication, and this result is considered to be due to the formation of non-stochiometric Y-Ti-oxides.

The effect of reported high-velocity small raindrops on inferred drop size distributions and derived power laws

Directory of Open Access Journals (Sweden)

H. Leijnse

2010-07-01

Full Text Available It has recently been shown that at high rainfall intensities, small raindrops may fall with much larger velocities than would be expected from their diameters. These were argued to be fragments of recently broken-up larger drops. In this paper we quantify the effect of this phenomenon on raindrop size distribution measurements from a Joss-Waldvogel disdrometer, a 2-D Video Distrometer, and a vertically-pointing Doppler radar. Probability distributions of fall velocities have been parameterized, where the parameters are functions of both rainfall intensity and drop size. These parameterizations have been used to correct Joss-Waldvogel disdrometer measurements for this phenomenon. The effect of these corrections on fitted scaled drop size distributions are apparent but not major. Fitted gamma distributions for three different types of rainfall have been used to simulate drop size measurements. The effect of the high-velocity small drops is shown to be minor. Especially for the purpose of remote sensing of rainfall using radar, microwave links, or optical links, the errors caused by using the slightly different retrieval relations will be masked completely by other error sources.

Small to Mid-Size Sporting Events: Are We Prepared to Recover from an Attack?

Directory of Open Access Journals (Sweden)

Brian M. Harrell

2010-01-01

Full Text Available This article describes a fictional deadly attack by a lone-wolf terrorist during a high school football event in a small town, here in the United States. The authors begin by describing an attack and then focus on the response from the medical community, city, county, state, and federal government officials. Next, the authors make several recommendations on what actions are needed to develop an effective plan to combat terrorist activities during a small- to mid-size sports event. Among the actions needed, the authors focus on the following: response planning, emergency action plan, incident command, policies and procedures, and security staff training.

Preliminary study of diagnostic workstation with different matrix size for detection of small pulmonary nodules

International Nuclear Information System (INIS)

Wu Jie; Wang Xuejian; Wang Bo; Tong Juan; Wei Yuqing; Shen Guiquan; Wang Limei; Cao Jun; Sui He

2004-01-01

Objective: To assess the influence in detecting small pulmonary nodules (SPNs) on soft-copy images displayed with different matrix sizes. Methods: Seventy-six chest compute radiographs were selected for the study. Of the 76 test images, 36 pulmonary nodules smaller than 20 mm in diameter were proven by CT, which were further divided into two groups: 1.0-2.0 cm and Z values and standard error of three kinds of view system for individual observers. Results: For 1.0-2.0 cm group, the mean A Z values were 0.7936 for DRCS with 2-fold magnification and window technique, 0.8225 for 1 K monitor with 2-fold magnification and window technique, and 0.8367 for 2 K monitor without magnification; for Z values increased slightly as the display matrix size improved, but there were no significant differences among the three sets in the detection of SPNs in the ROC analyses. Conclusion: It is acceptable to detect small pulmonary nodules of 1.0-2.0 cm in diameter on 1 K monitor and DRCS with magnification. High resolution diagnostic workstation is recommended for detecting small pulmonary nodules <1.0 cm in diameter. Reasonable equipment for the detection of subtle abnormality may result in better cost-efficacy and diagnostic accuracy

Barriers to Employee Training in Small and Medium Sized Enterprises: Insights and Evidences from Mauritius

Science.gov (United States)

Padachi, Kesseven; Bhiwajee, Soolakshna Lukea

2016-01-01

Purpose: Training is an important component of successful business concerns. However, although there is growing acceptance amongst scholars that small- and medium-sized enterprises (SMEs) are engines that drive economies across nations, through their contribution in terms of job creation and poverty reduction; extant research portray that these…

Multi-SOM: an Algorithm for High-Dimensional, Small Size Datasets

Directory of Open Access Journals (Sweden)

Shen Lu

2013-04-01

Full Text Available Since it takes time to do experiments in bioinformatics, biological datasets are sometimes small but with high dimensionality. From probability theory, in order to discover knowledge from a set of data, we have to have a sufficient number of samples. Otherwise, the error bounds can become too large to be useful. For the SOM (Self- Organizing Map algorithm, the initial map is based on the training data. In order to avoid the bias caused by the insufficient training data, in this paper we present an algorithm, called Multi-SOM. Multi-SOM builds a number of small self-organizing maps, instead of just one big map. Bayesian decision theory is used to make the final decision among similar neurons on different maps. In this way, we can better ensure that we can get a real random initial weight vector set, the map size is less of consideration and errors tend to average out. In our experiments as applied to microarray datasets which are highly intense data composed of genetic related information, the precision of Multi-SOMs is 10.58% greater than SOMs, and its recall is 11.07% greater than SOMs. Thus, the Multi-SOMs algorithm is practical.

Characterization of Nano Sized Microstructures in Fe and Ni Base ODS Alloys Using Small Angle Neutron Scattering

International Nuclear Information System (INIS)

Han, Young-Soo; Jang, Jin-Sung; Mao, Xiaodong

2015-01-01

Ferritic ODS(Oxide-dispersion-strengthened) alloy is known as a primary candidate material of the cladding tubes of a sodium fast reactor (SFR) in the Generation IV research program. In ODS alloy, the major contribution to the enhanced high-temperature mechanical property comes from the existence of nano-sized oxide precipitates, which act as obstacles to the movement of dislocations. In addition for the extremely high temperature application(>950 .deg. C) of future nuclear system, Ni base ODS alloys are considered as candidate materials. Therefore the characterization of nano-sized microstructures is important for determining the mechanical properties of the material. Small angle neutron scattering (SANS) technique non-destructively probes structures in materials at the nano-meter length of scale (1 - 1000 nm) and has been a very powerful tool in a variety of scientific/engineering research areas. In this study, nano-sized microstructures were quantitatively analyzed by small angle neutron scattering. Quantitative microstructural information on nanosized oxide in ODS alloys was obtained from SANS data. The effects of the thermo mechanical treatment on the size and volume fraction of nano-sized oxides were analyzed. For 12Cr ODS alloy, the experimental A-ratio is two-times larger than the theoretical A-ratio., and this result is considered to be due to the imperfections included in YTaO 4 . For Ni base ODS alloy, the volume fraction of the mid-sized particles (- 30 nm) increases rapidly as hot extrusion temperature decreases

Digital Image Collections for Asian Religion and Art History in a Small-Sized Liberal Arts College

Directory of Open Access Journals (Sweden)

May Chang

2002-10-01

Full Text Available

頁次：6-15

size: small;">This paper reviews the establishment of a digital image library from 35mm slides to support faculty and student needs in a small-sized liberal arts college. The framework consists of central local resources, distributed faculty collections, and external resources. Standards and guidelines for digital preservation and access are also discussed. The pilot collections were multi-disciplinary resources in Middle East art and architecture and faculty slide collections in East Asian religions and Asian art history. Technical and management issues of integrating digital technology in the traditional slide library are also discussed.

Numerical simulation for the magnetic force distribution in electromagnetic forming of small size flat sheet

Science.gov (United States)

Chen, Xiaowei; Wang, Wenping; Wan, Min

2013-12-01

It is essential to calculate magnetic force in the process of studying electromagnetic flat sheet forming. Calculating magnetic force is the basis of analyzing the sheet deformation and optimizing technical parameters. Magnetic force distribution on the sheet can be obtained by numerical simulation of electromagnetic field. In contrast to other computing methods, the method of numerical simulation has some significant advantages, such as higher calculation accuracy, easier using and other advantages. In this paper, in order to study of magnetic force distribution on the small size flat sheet in electromagnetic forming when flat round spiral coil, flat rectangular spiral coil and uniform pressure coil are adopted, the 3D finite element models are established by software ANSYS/EMAG. The magnetic force distribution on the sheet are analyzed when the plane geometries of sheet are equal or less than the coil geometries under fixed discharge impulse. The results showed that when the physical dimensions of sheet are less than the corresponding dimensions of the coil, the variation of induced current channel width on the sheet will cause induced current crowding effect that seriously influence the magnetic force distribution, and the degree of inhomogeneity of magnetic force distribution is increase nearly linearly with the variation of induced current channel width; the small size uniform pressure coil will produce approximately uniform magnetic force distribution on the sheet, but the coil is easy to early failure; the desirable magnetic force distribution can be achieved when the unilateral placed flat rectangular spiral coil is adopted, and this program can be take as preferred one, because the longevity of flat rectangular spiral coil is longer than the working life of small size uniform pressure coil.

Impact of mobility on call block, call drops and optimal cell size in small cell networks

OpenAIRE

Ramanath , Sreenath; Voleti , Veeraruna Kavitha; Altman , Eitan

2011-01-01

We consider small cell networks and study the impact of user mobility. Assuming Poisson call arrivals at random positions with random velocities, we discuss the characterization of handovers at the boundaries. We derive explicit expressions for call block and call drop probabilities using tools from spatial queuing theory. We also derive expressions for the average virtual server held up time. These expressions are used to derive optimal cell sizes for various profile of velocities in small c...

Sensitivity and specificity of normality tests and consequences on reference interval accuracy at small sample size: a computer-simulation study.

Science.gov (United States)

Le Boedec, Kevin

2016-12-01

According to international guidelines, parametric methods must be chosen for RI construction when the sample size is small and the distribution is Gaussian. However, normality tests may not be accurate at small sample size. The purpose of the study was to evaluate normality test performance to properly identify samples extracted from a Gaussian population at small sample sizes, and assess the consequences on RI accuracy of applying parametric methods to samples that falsely identified the parent population as Gaussian. Samples of n = 60 and n = 30 values were randomly selected 100 times from simulated Gaussian, lognormal, and asymmetric populations of 10,000 values. The sensitivity and specificity of 4 normality tests were compared. Reference intervals were calculated using 6 different statistical methods from samples that falsely identified the parent population as Gaussian, and their accuracy was compared. Shapiro-Wilk and D'Agostino-Pearson tests were the best performing normality tests. However, their specificity was poor at sample size n = 30 (specificity for P Box-Cox transformation) on all samples regardless of their distribution or adjusting, the significance level of normality tests depending on sample size would limit the risk of constructing inaccurate RI. © 2016 American Society for Veterinary Clinical Pathology.

Evaluation of ECT reliability for axial ODSCC in steam generator tubes

International Nuclear Information System (INIS)

Lee, Jae Bong; Park, Jai Hak; Kim, Hong Deok; Chung, Han Sub

2010-01-01

The integrity of steam generator tubes is usually evaluated based on eddy current test (ECT) results. Because detection capacity of the ECT is not perfect, all of the physical flaws, which actually exist in steam generator tubes, cannot be detected by ECT inspection. Therefore it is very important to analyze ECT reliability in the integrity assessment of steam generators. The reliability of an ECT inspection system is divided into reliability of inspection technique and reliability of quality of analyst. And the reliability of ECT results is also divided into reliability of size and reliability of detection. The reliability of ECT sizing is often characterized as a linear regression model relating true flaw size data to measured flaw size data. The reliability of detection is characterized in terms of probability of detection (POD), which is expressed as a function of flaw size. In this paper the reliability of an ECT inspection system is analyzed quantitatively. POD of the ECT inspection system for axial outside diameter stress corrosion cracks (ODSCC) in steam generator tubes is evaluated. Using a log-logistic regression model, POD is evaluated from hit (detection) and miss (no detection) binary data obtained from destructive and non-destructive inspections of cracked tubes. Crack length and crack depth are considered as variables in multivariate log-logistic regression and their effects on detection capacity are assessed using two-dimensional POD (2-D POD) surface. The reliability of detection is also analyzed using POD for inspection technique (POD T ) and POD for analyst (POD A ).

Particle size distribution models of small angle neutron scattering pattern on ferro fluids

International Nuclear Information System (INIS)

Sistin Asri Ani; Darminto; Edy Giri Rachman Putra

2009-01-01

The Fe 3 O 4 ferro fluids samples were synthesized by a co-precipitation method. The investigation of ferro fluids microstructure is known to be one of the most important problems because the presence of aggregates and their internal structure influence greatly the properties of ferro fluids. The size and the size dispersion of particle in ferro fluids were determined assuming a log normal distribution of particle radius. The scattering pattern of the measurement by small angle neutron scattering were fitted by the theoretical scattering function of two limitation models are log normal sphere distribution and fractal aggregate. Two types of particle are detected, which are presumably primary particle of 30 Armstrong in radius and secondary fractal aggregate of 200 Armstrong with polydispersity of 0.47 up to 0.53. (author)

Latent hardening size effect in small-scale plasticity

Science.gov (United States)

Bardella, Lorenzo; Segurado, Javier; Panteghini, Andrea; Llorca, Javier

2013-07-01

We aim at understanding the multislip behaviour of metals subject to irreversible deformations at small-scales. By focusing on the simple shear of a constrained single-crystal strip, we show that discrete Dislocation Dynamics (DD) simulations predict a strong latent hardening size effect, with smaller being stronger in the range [1.5 µm, 6 µm] for the strip height. We attempt to represent the DD pseudo-experimental results by developing a flow theory of Strain Gradient Crystal Plasticity (SGCP), involving both energetic and dissipative higher-order terms and, as a main novelty, a strain gradient extension of the conventional latent hardening. In order to discuss the capability of the SGCP theory proposed, we implement it into a Finite Element (FE) code and set its material parameters on the basis of the DD results. The SGCP FE code is specifically developed for the boundary value problem under study so that we can implement a fully implicit (Backward Euler) consistent algorithm. Special emphasis is placed on the discussion of the role of the material length scales involved in the SGCP model, from both the mechanical and numerical points of view.

Latent hardening size effect in small-scale plasticity

International Nuclear Information System (INIS)

Bardella, Lorenzo; Panteghini, Andrea; Segurado, Javier; Llorca, Javier

2013-01-01

We aim at understanding the multislip behaviour of metals subject to irreversible deformations at small-scales. By focusing on the simple shear of a constrained single-crystal strip, we show that discrete Dislocation Dynamics (DD) simulations predict a strong latent hardening size effect, with smaller being stronger in the range [1.5 µm, 6 µm] for the strip height. We attempt to represent the DD pseudo-experimental results by developing a flow theory of Strain Gradient Crystal Plasticity (SGCP), involving both energetic and dissipative higher-order terms and, as a main novelty, a strain gradient extension of the conventional latent hardening. In order to discuss the capability of the SGCP theory proposed, we implement it into a Finite Element (FE) code and set its material parameters on the basis of the DD results. The SGCP FE code is specifically developed for the boundary value problem under study so that we can implement a fully implicit (Backward Euler) consistent algorithm. Special emphasis is placed on the discussion of the role of the material length scales involved in the SGCP model, from both the mechanical and numerical points of view. (paper)

Using multi-theory model to predict initiation and sustenance of small portion size consumption among college students

Directory of Open Access Journals (Sweden)

Manoj Sharma

2016-08-01

Conclusion: Based on this study’s findings, MTM appears to be a robust theoretical framework for predicting small portion size consumption behavior change. Interventions in this regard need to be designed.

Bayesian Reliability Estimation for Deteriorating Systems with Limited Samples Using the Maximum Entropy Approach

OpenAIRE

Xiao, Ning-Cong; Li, Yan-Feng; Wang, Zhonglai; Peng, Weiwen; Huang, Hong-Zhong

2013-01-01

In this paper the combinations of maximum entropy method and Bayesian inference for reliability assessment of deteriorating system is proposed. Due to various uncertainties, less data and incomplete information, system parameters usually cannot be determined precisely. These uncertainty parameters can be modeled by fuzzy sets theory and the Bayesian inference which have been proved to be useful for deteriorating systems under small sample sizes. The maximum entropy approach can be used to cal...

Methodologies and Decision Criteria for Demonstrating Competitiveness of Small and Medium Sized Reactors - Present Value Capital Cost Model. Annex VIII

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-12-15

Smaller size reactors are required to fulfil the growing energy needs of developing countries and emerging markets, as well as niche markets in developed countries. Grid appropriate reactors have been identified within the United States Department of Energy Global Nuclear Energy Partnership initiative as one of the key elements required to enable worldwide expansion of the peaceful use of nuclear power. In a speech at a conference in Algiers on 9 January 2007, the former IAEA Director General, Mohamed El Baradei, discussed the interest in new small and medium-size reactor designs which allow a more incremental investment than is required for a big reactor, and provide a better match to grid capacity in many developing countries'. Smaller size reactors (IAEA defines as 'small' those reactors with a power <300 MW(e) and 'medium' with a power <700 MW(e)) are the logical choice for smaller countries or those with a limited electrical grid. In fact, smaller reactors are now in different stages of development throughout the world, and interest in their deployment has also been expressed. With regards to decisions on the addition of power plant capacity, small reactors have many attractive characteristics, namely size, simplicity, enhanced safety, cost savings and lower financial resource requirements. On the downside, the specific costs of some components and systems of small and medium sized reactors (SMRs) may be higher as a result of economy of scale effects. This annex explores some of the factors affecting decisions on power plant capacity addition in world markets, focusing particularly on many of the characteristics of SMRs.

Metastable structures and size effects in small group dynamics

Directory of Open Access Journals (Sweden)

Rosapia eLauro Grotto

2014-07-01

Full Text Available In his seminal works on group dynamics Bion defined a specific therapeutic setting allowing psychoanalytic observations on group phenomena. In describing the setting he proposed that the group was where his voice arrived. This physical limit was later made operative by assuming that the natural dimension of a therapeutic group is around 12 people. Bion introduced a theory of the group aspects of the mind in which proto-mental individual states spontaneously evolve into shared psychological states that are characterized by a series of features: 1 they emerge as a consequence of the natural tendency of (both conscious and unconscious emotions to combine into structured group patterns; 2 they have a certain degree of stability in time; 3 they tend to alternate so that the dissolution of one is rapidly followed by the emergence of another; 4 they can be described in qualitative terms according to the nature of the emotional mix that dominates the state, in structural terms by a kind of typical 'leadership’ pattern, and in 'cognitive’ terms by a set of implicit expectations that are helpful in explaining the group behavior (i.e. the group behaves 'as if’ it was assuming that…. Here we adopt a formal approach derived from Socio-physics in order to explore some of the structural and dynamic properties of this small group dynamics. We will described data from an analytic DS model simulating small group interactions of agents endowed with a very simplified emotional and cognitive dynamic in order to assess the following main points: 1 are metastable collective states allowed to emerge in the model and if so, under which conditions in the parameter space? 3 can these states be differentiated in structural terms? 3 to what extent are the emergent dynamic features of the systems dependent of the system size? We will finally discuss possible future applications of the quantitative descriptions of the interaction structure in the small group clinical

Metastable structures and size effects in small group dynamics.

Science.gov (United States)

Lauro Grotto, Rosapia; Guazzini, Andrea; Bagnoli, Franco

2014-01-01

In his seminal works on group dynamics Bion defined a specific therapeutic setting allowing psychoanalytic observations on group phenomena. In describing the setting he proposed that the group was where his voice arrived. This physical limit was later made operative by assuming that the natural dimension of a therapeutic group is around 12 people. Bion introduced a theory of the group aspects of the mind in which proto-mental individual states spontaneously evolve into shared psychological states that are characterized by a series of features: (1) they emerge as a consequence of the natural tendency of (both conscious and unconscious) emotions to combine into structured group patterns; (2) they have a certain degree of stability in time; (3) they tend to alternate so that the dissolution of one is rapidly followed by the emergence of another; (4) they can be described in qualitative terms according to the nature of the emotional mix that dominates the state, in structural terms by a kind of typical "leadership" pattern, and in "cognitive" terms by a set of implicit expectations that are helpful in explaining the group behavior (i.e., the group behaves "as if" it was assuming that). Here we adopt a formal approach derived from Socio-physics in order to explore some of the structural and dynamic properties of this small group dynamics. We will described data from an analytic DS model simulating small group interactions of agents endowed with a very simplified emotional and cognitive dynamic in order to assess the following main points: (1) are metastable collective states allowed to emerge in the model and if so, under which conditions in the parameter space? (2) can these states be differentiated in structural terms? (3) to what extent are the emergent dynamic features of the systems dependent of the system size? We will finally discuss possible future applications of the quantitative descriptions of the interaction structure in the small group clinical setting.

Modelling of the costs of decision support for small and medium-sized enterprises

Directory of Open Access Journals (Sweden)

Viera Tomišová

2017-01-01

Full Text Available The support of decision-making activities in small and medium-sized enterprises (SME has its specific features. When suggesting steps for the implementation of decision-support tools in the enterprise, we identified two main ways of decision-making support based on the data analysis: ERP (Enterprise Resource Planning without BI (Business Intelligence and ERP with BI. In our contribution, we present costs models of both mentioned decision support systems and their practical interpretation.

Three-dimensional computed tomography measurement accuracy of varying Hill-Sachs lesion size.

Science.gov (United States)

Ho, Anthony; Kurdziel, Michael D; Koueiter, Denise M; Wiater, J Michael

2018-02-01

The glenoid track concept has been proposed to correlate shoulder stability with bone loss. Accurate assessment of Hill-Sachs lesion size preoperatively may affect surgical planning and postoperative outcomes; however, no measurement method has been universally accepted. This study aimed to assess the accuracy and reliability of measuring Hill-Sachs lesion sizes using 3-dimensional (3D) computed tomography (CT). Nine polyurethane humerus bone substitutes were used to create Hill-Sachs lesions of varying sizes with a combination of lesion depth (shallow, intermediate, and deep) and width (small, medium, and large). Specimens were scanned with a clinical CT scanner for size measurements and a micro-CT scanner for measurement of true lesion size. Six evaluators repeated measurements twice in a 2-week interval. Scans were measured by use of 3D CT reconstructions for length, width, and Hill-Sachs interval and with use of 2D CT for depth. The interclass correlation coefficient evaluated interobserver and intraobserver variability and percentage error, and Student t-tests assessed measurement accuracy. Interclass correlation coefficient reliability demonstrated strong agreement for all variables measured (0.856-0.975). Percentage error between measured length and measured depth and the true measurement significantly varied with respect to both lesion depth (P = .003 and P = .005, respectively) and lesion size (P = .049 and P = .004, respectively). The 3D CT imaging is effective and reproducible in determining lesion size. Determination of Hill-Sachs interval width is also reliable when it is applied to the glenoid track concept. Measured values on 3D and 2-dimensional imaging using a conventional CT scanner may slightly underestimate true measurements. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

Non-farm businesses local economic integration level: the case of six Portuguese small and medium-sized Markettowns - a sector approach

OpenAIRE

Diniz, Francisco

2004-01-01

Small and medium-sized towns in rural areas are of particular interest at this stage in the evolution of the European CAP. Serious consideration is being given to mechanisms that could transfer resources from the agricultural sector into a more diversified rural economy in order to safeguard the well-being of both the farming community and the wider rural population while still preserving the environmental assets which are such a valued feature of Europe's rural areas. Small and medium-sized ...

Results of a Demonstration Assessment of Passive System Reliability Utilizing the Reliability Method for Passive Systems (RMPS)

Energy Technology Data Exchange (ETDEWEB)

Bucknor, Matthew; Grabaskas, David; Brunett, Acacia; Grelle, Austin

2015-04-26

Advanced small modular reactor designs include many advantageous design features such as passively driven safety systems that are arguably more reliable and cost effective relative to conventional active systems. Despite their attractiveness, a reliability assessment of passive systems can be difficult using conventional reliability methods due to the nature of passive systems. Simple deviations in boundary conditions can induce functional failures in a passive system, and intermediate or unexpected operating modes can also occur. As part of an ongoing project, Argonne National Laboratory is investigating various methodologies to address passive system reliability. The Reliability Method for Passive Systems (RMPS), a systematic approach for examining reliability, is one technique chosen for this analysis. This methodology is combined with the Risk-Informed Safety Margin Characterization (RISMC) approach to assess the reliability of a passive system and the impact of its associated uncertainties. For this demonstration problem, an integrated plant model of an advanced small modular pool-type sodium fast reactor with a passive reactor cavity cooling system is subjected to a station blackout using RELAP5-3D. This paper discusses important aspects of the reliability assessment, including deployment of the methodology, the uncertainty identification and quantification process, and identification of key risk metrics.

Communicating Hydrocephalus Associated with Small- to Medium-Sized Vestibular Schwannomas: Clinical Significance of the Tumor Apparent Diffusion Coefficient Map.

Science.gov (United States)

Taniguchi, Masaaki; Nakai, Tomoaki; Kohta, Masaaki; Kimura, Hidehito; Kohmura, Eiji

2016-10-01

The etiology of hydrocephalus associated with the small- to medium-sized vestibular schwannomas is still controversial. We investigated tumor-specific factors related to the association of hydrocephalus with small- to medium-sized vestibular schwannomas. Among the 77 patients with vestibular schwannoma smaller than 30 mm, 9 patients demonstrated associated communicating hydrocephalus. Patient medical records, radiologic data, and histopathologic specimens were reviewed retrospectively. The age of the patients, and size, mean apparent diffusion coefficient (ADC) value, and histologic features of the tumors were compared with those of patients without hydrocephalus. The symptoms related to hydrocephalus improved in all patients after tumor removal. Both the mean size and ADC values exhibited a statistically significant difference between the tumors with and without hydrocephalus (P hydrocephalus. The increased tumor ADC value was considered to be the result of degenerative change and suggested the involvement of protein sloughing in the etiology of the associated hydrocephalus. Copyright © 2016 Elsevier Inc. All rights reserved.

MEASUREMENT: ACCOUNTING FOR RELIABILITY IN PERFORMANCE ESTIMATES.

Science.gov (United States)

Waterman, Brian; Sutter, Robert; Burroughs, Thomas; Dunagan, W Claiborne

2014-01-01

When evaluating physician performance measures, physician leaders are faced with the quandary of determining whether departures from expected physician performance measurements represent a true signal or random error. This uncertainty impedes the physician leader's ability and confidence to take appropriate performance improvement actions based on physician performance measurements. Incorporating reliability adjustment into physician performance measurement is a valuable way of reducing the impact of random error in the measurements, such as those caused by small sample sizes. Consequently, the physician executive has more confidence that the results represent true performance and is positioned to make better physician performance improvement decisions. Applying reliability adjustment to physician-level performance data is relatively new. As others have noted previously, it's important to keep in mind that reliability adjustment adds significant complexity to the production, interpretation and utilization of results. Furthermore, the methods explored in this case study only scratch the surface of the range of available Bayesian methods that can be used for reliability adjustment; further study is needed to test and compare these methods in practice and to examine important extensions for handling specialty-specific concerns (e.g., average case volumes, which have been shown to be important in cardiac surgery outcomes). Moreover, it's important to note that the provider group average as a basis for shrinkage is one of several possible choices that could be employed in practice and deserves further exploration in future research. With these caveats, our results demonstrate that incorporating reliability adjustment into physician performance measurements is feasible and can notably reduce the incidence of "real" signals relative to what one would expect to see using more traditional approaches. A physician leader who is interested in catalyzing performance improvement

Behavior of small-sized BWR fuel under reactivity initiated accident conditions

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki; Fujishiro, Toshio; Horiki, Oichiro; Chen Dianshan; Takeuchi, Kiyoshi.

1992-01-01

The present work was performed on this small-sized BWR fuel, where Zr liner and rod prepressurization were taken as experimental parameters. Experiment was done under simulated reactivity initiated accident (RIA) conditions at Nuclear Safety Research Reactor (NSRR) belonged to Japan Atomic Energy Research Institute (JAERI). Major remarks obtained are as follows: (1) Three different types of the fuel rods consisted of (a) Zr lined/pressurized (0.65MPa), (b) Zr lined/non-pressurized and (c) non-Zr lined/pressurized (o.65MPa) were used, respectively. Failure thresholds of these were not less than that (260 cal/g·fuel) described in Japanese RIA Licensing Guideline. Small-sized BWR and conventional 8 x 8 BWR fuels were considered to be in almost the same level in failure threshold. Failure modes of the three were (a) cladding melt/brittle, (b) cladding melt/brittle and (c) rupture by large ballooning, respectively. (2) The magnitude of pressure pulse at fuel fragmentation was also studied by lined/pressurized and non-lined/pressurized fuels. Above the energy deposition of 370 cal/g·fuel, mechanical energy (or pressure) was found to be released from these fragmented fuels. No measurable difference was, however, observed between the tested fuels and NSRR standard (and conventional 8 x 8 BWR) fuels. (3) It is worthy of mentioning that Zr liner tended to prevent the cladding from large ballooning. Non-lined/pressurized fuel tended to cause wrinkle deformation at cladding. Hence, cladding external was notched much by the wrinkles. (4) Time to fuel failure measured from the tested BWR fuels (pressurization < 0.6MPA) was longer than that measured from PWR fuels (pressurization < 3.2MPa). The magnitude of the former was of the order of 3 ∼ 6s, while that of the latter was < 1s. (J.P.N.)

Prognostic Significance of Tumor Size of Small Lung Adenocarcinomas Evaluated with Mediastinal Window Settings on Computed Tomography

OpenAIRE

Sakao, Yukinori; Kuroda, Hiroaki; Mun, Mingyon; Uehara, Hirofumi; Motoi, Noriko; Ishikawa, Yuichi; Nakagawa, Ken; Okumura, Sakae

2014-01-01

BACKGROUND: We aimed to clarify that the size of the lung adenocarcinoma evaluated using mediastinal window on computed tomography is an important and useful modality for predicting invasiveness, lymph node metastasis and prognosis in small adenocarcinoma. METHODS: We evaluated 176 patients with small lung adenocarcinomas (diameter, 1-3 cm) who underwent standard surgical resection. Tumours were examined using computed tomography with thin section conditions (1.25 mm thick on high-resolution ...

Does company size matter? Validation of an integrative model of safety behavior across small and large construction companies.

Science.gov (United States)

Guo, Brian H W; Yiu, Tak Wing; González, Vicente A

2018-02-01

Previous safety climate studies primarily focused on either large construction companies or the construction industry as a whole, while little is known about whether company size has significant effects on workers' understanding of safety climate measures and relationships between safety climate factors and safety behavior. Thus, this study aims to: (a) test the measurement equivalence (ME) of a safety climate measure across workers from small and large companies; (b) investigate if company size alters the causal structure of the integrative model developed by Guo, Yiu, and González (2016). Data were collected from 253 construction workers in New Zealand using a safety climate measure. This study used multi-group confirmatory factor analyses (MCFA) to test the measurement equivalence of the safety climate measure and structure invariance of the integrative model. Results indicate that workers from small and large companies understood the safety climate measure in a similar manner. In addition, it was suggested that company size does not change the causal structure and mediational processes of the integrative model. Both measurement equivalence of the safety climate measure and structural invariance of the integrative model were supported by this study. Practical applications: Findings of this study provided strong support for a meaningful use of the safety climate measure across construction companies in different sizes. Safety behavior promotion strategies designed based on the integrative model may be well suited for both large and small companies. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

SU-E-T-432: Field Size Influence On the Electron and Photon Spectra Within Small MV Field Detectors

Energy Technology Data Exchange (ETDEWEB)

Benmakhlouf, H; Andreo, P [Department of Medical Physics, Karolinska University Hospital, Stockholm and Department of Physics, Medical Radiation Physics, Stockholm University (Sweden)

2015-06-15

Purpose: To investigate the influence of photon field size on the electron and photon fluence spectra in the active volume of small field detectors. Methods: The PENELOPE MC system based usercode PenEasy was used to calculate the material influence on the spectra by scoring the differential fluence in inserts of silicon, carbon, phosphorus and aluminium having 3 mm diameter and height. The spectra were then calculated inside the active volume of eleven detectors (ion chambers and solid-state detectors) whose geometry was simulated with great detail. The inserts/detectors were placed at 10 cm depth in a 30 cm x 30 cm x 30 cm water phantom and irradiated with 2.5 MeV photons and Varian Clinac 6 MV beams of small, medium and large size. Results: For all configurations, photon spectra in the scoring volume were similar to that in a small water volume except for additional characteristic x-ray peaks resulting from the material itself and from the materials surrounding the detectors (i.e. high-Z shielding the silicon). Electron fluence calculated in the inserts were up to 60% larger than in water; the difference increased with material density and decreasing field size. MC-calculated doses were compared to analytically determined collision kerma and restricted cema (cut-off=15keV). For the inserts, with large and medium fields K-col agreed with MC-dose, but K-col overestimated the dose for small fields due to lack of lateral CPE. For the detectors, up to 15% differences between K-col and the MC-dose were found. For all configurations the C-delta and MC-dose agreed within ±2%. Conclusion: The most relevant findings were that shielding affects substantially the photon spectra and material conditions the electron spectra, their field size dependence varying with the geometry configuration. These affect the values of factors entering into relative dosimetry.

Optimal unit sizing for small-scale integrated energy systems using multi-objective interval optimization and evidential reasoning approach

International Nuclear Information System (INIS)

Wei, F.; Wu, Q.H.; Jing, Z.X.; Chen, J.J.; Zhou, X.X.

2016-01-01

This paper proposes a comprehensive framework including a multi-objective interval optimization model and evidential reasoning (ER) approach to solve the unit sizing problem of small-scale integrated energy systems, with uncertain wind and solar energies integrated. In the multi-objective interval optimization model, interval variables are introduced to tackle the uncertainties of the optimization problem. Aiming at simultaneously considering the cost and risk of a business investment, the average and deviation of life cycle cost (LCC) of the integrated energy system are formulated. In order to solve the problem, a novel multi-objective optimization algorithm, MGSOACC (multi-objective group search optimizer with adaptive covariance matrix and chaotic search), is developed, employing adaptive covariance matrix to make the search strategy adaptive and applying chaotic search to maintain the diversity of group. Furthermore, ER approach is applied to deal with multiple interests of an investor at the business decision making stage and to determine the final unit sizing solution from the Pareto-optimal solutions. This paper reports on the simulation results obtained using a small-scale direct district heating system (DH) and a small-scale district heating and cooling system (DHC) optimized by the proposed framework. The results demonstrate the superiority of the multi-objective interval optimization model and ER approach in tackling the unit sizing problem of integrated energy systems considering the integration of uncertian wind and solar energies. - Highlights: • Cost and risk of investment in small-scale integrated energy systems are considered. • A multi-objective interval optimization model is presented. • A novel multi-objective optimization algorithm (MGSOACC) is proposed. • The evidential reasoning (ER) approach is used to obtain the final optimal solution. • The MGSOACC and ER can tackle the unit sizing problem efficiently.

The Maximum standardized uptake value is more reliable than size measurement in early follow-up to evaluate potential pulmonary malignancies following radiofrequency ablation.

Science.gov (United States)

Alafate, Aierken; Shinya, Takayoshi; Okumura, Yoshihiro; Sato, Shuhei; Hiraki, Takao; Ishii, Hiroaki; Gobara, Hideo; Kato, Katsuya; Fujiwara, Toshiyoshi; Miyoshi, Shinichiro; Kaji, Mitsumasa; Kanazawa, Susumu

2013-01-01

We retrospectively evaluated the accumulation of fluorodeoxy glucose (FDG) in pulmonary malignancies without local recurrence during 2-year follow-up on positron emission tomography (PET)/computed tomography (CT) after radiofrequency ablation (RFA). Thirty tumors in 25 patients were studied (10 non-small cell lung cancers;20 pulmonary metastatic tumors). PET/CT was performed before RFA, 3 months after RFA, and 6 months after RFA. We assessed the FDG accumulation with the maximum standardized uptake value (SUVmax) compared with the diameters of the lesions. The SUVmax had a decreasing tendency in the first 6 months and, at 6 months post-ablation, FDG accumulation was less affected by inflammatory changes than at 3 months post-RFA. The diameter of the ablated lesion exceeded that of the initial tumor at 3 months post-RFA and shrank to pre-ablation dimensions by 6 months post-RFA. SUVmax was more reliable than the size measurements by CT in the first 6 months after RFA, and PET/CT at 6 months post-RFA may be more appropriate for the assessment of FDG accumulation than that at 3 months post-RFA.

Rapid and reliable healing of critical size bone defects with genetically modified sheep muscle.

Science.gov (United States)

Liu, F; Ferreira, E; Porter, R M; Glatt, V; Schinhan, M; Shen, Z; Randolph, M A; Kirker-Head, C A; Wehling, C; Vrahas, M S; Evans, C H; Wells, J W

2015-09-21

Large segmental defects in bone fail to heal and remain a clinical problem. Muscle is highly osteogenic, and preliminary data suggest that autologous muscle tissue expressing bone morphogenetic protein-2 (BMP-2) efficiently heals critical size defects in rats. Translation into possible human clinical trials requires, inter alia, demonstration of efficacy in a large animal, such as the sheep. Scale-up is fraught with numerous biological, anatomical, mechanical and structural variables, which cannot be addressed systematically because of cost and other practical issues. For this reason, we developed a translational model enabling us to isolate the biological question of whether sheep muscle, transduced with adenovirus expressing BMP-2, could heal critical size defects in vivo. Initial experiments in athymic rats noted strong healing in only about one-third of animals because of unexpected immune responses to sheep antigens. For this reason, subsequent experiments were performed with Fischer rats under transient immunosuppression. Such experiments confirmed remarkably rapid and reliable healing of the defects in all rats, with bridging by 2 weeks and remodelling as early as 3-4 weeks, despite BMP-2 production only in nanogram quantities and persisting for only 1-3 weeks. By 8 weeks the healed defects contained well-organised new bone with advanced neo-cortication and abundant marrow. Bone mineral content and mechanical strength were close to normal values. These data demonstrate the utility of this model when adapting this technology for bone healing in sheep, as a prelude to human clinical trials.

In Good Company : When Small and Medium-sized Enterprises Acquire Multiplex Knowledge from Key Commercial Partners

NARCIS (Netherlands)

Bojica, Ana Maria; Estrada Vaquero, Isabel; del Mar Fuentes-Fuentes, Maria

2018-01-01

This study explores the specific conditions under which key strategic alliances of small and medium-sized enterprises (SMEs) with commercial partners can become multiplex in knowledge exchange. Using survey data from a sample of 150 Spanish SMEs in the information and communication technology (ICT)

Traceable size determination of PMMA nanoparticles based on Small Angle X-ray Scattering (SAXS)

Energy Technology Data Exchange (ETDEWEB)

Gleber, G; Cibik, L; Mueller, P; Krumrey, M [Physikalisch-Technische Bundesanstalt (PTB), Abbestrasse 2-12, 10587 Berlin (Germany); Haas, S; Hoell, A, E-mail: gudrun.gleber@ptb.d [Helmholtz-Zentrum-Berlin fuer Materialien und Energie (HZB), Albert-Einstein-Strasse 15, 12489 Berlin (Germany)

2010-10-01

The size and size distribution of PMMA nanoparticles has been investigated with SAXS (small angle X-ray scattering) using monochromatized synchrotron radiation. The uncertainty has contributions from the wavelength or photon energy of the radiation, the scattering angle and the fit procedure for the obtained scattering curves. The wavelength can be traced back to the lattice constant of silicon, and the scattering angle is traceable via geometric measurements of the detector pixel size and the distance between the sample and the detector. SAXS measurements and data evaluations have been performed at different distances and photon energies for two PMMA nanoparticle suspensions with low polydispersity and nominal diameters of 108 nm and 192 nm, respectively, as well as for a mixture of both. The relative variation of the diameters obtained for different experimental conditions was below {+-} 0.3 %. The determined number-weighted mean diameters of (109.0 {+-} 0.7) nm and (188.0 {+-} 1.3) nm, respectively, are close to the nominal values.

Traceable size determination of PMMA nanoparticles based on Small Angle X-ray Scattering (SAXS)

Science.gov (United States)

Gleber, G.; Cibik, L.; Haas, S.; Hoell, A.; Müller, P.; Krumrey, M.

2010-10-01

The size and size distribution of PMMA nanoparticles has been investigated with SAXS (small angle X-ray scattering) using monochromatized synchrotron radiation. The uncertainty has contributions from the wavelength or photon energy of the radiation, the scattering angle and the fit procedure for the obtained scattering curves. The wavelength can be traced back to the lattice constant of silicon, and the scattering angle is traceable via geometric measurements of the detector pixel size and the distance between the sample and the detector. SAXS measurements and data evaluations have been performed at different distances and photon energies for two PMMA nanoparticle suspensions with low polydispersity and nominal diameters of 108 nm and 192 nm, respectively, as well as for a mixture of both. The relative variation of the diameters obtained for different experimental conditions was below ± 0.3 %. The determined number-weighted mean diameters of (109.0 ± 0.7) nm and (188.0 ± 1.3) nm, respectively, are close to the nominal values.

Traceable size determination of PMMA nanoparticles based on Small Angle X-ray Scattering (SAXS)

International Nuclear Information System (INIS)

Gleber, G; Cibik, L; Mueller, P; Krumrey, M; Haas, S; Hoell, A

2010-01-01

The size and size distribution of PMMA nanoparticles has been investigated with SAXS (small angle X-ray scattering) using monochromatized synchrotron radiation. The uncertainty has contributions from the wavelength or photon energy of the radiation, the scattering angle and the fit procedure for the obtained scattering curves. The wavelength can be traced back to the lattice constant of silicon, and the scattering angle is traceable via geometric measurements of the detector pixel size and the distance between the sample and the detector. SAXS measurements and data evaluations have been performed at different distances and photon energies for two PMMA nanoparticle suspensions with low polydispersity and nominal diameters of 108 nm and 192 nm, respectively, as well as for a mixture of both. The relative variation of the diameters obtained for different experimental conditions was below ± 0.3 %. The determined number-weighted mean diameters of (109.0 ± 0.7) nm and (188.0 ± 1.3) nm, respectively, are close to the nominal values.

78 FR 11745 - Small Business Size Regulations, Small Business Innovation Research (SBIR) Program and Small...

Science.gov (United States)

2013-02-20

.... As published, the final regulations contain two points where the word ``small'' was inadvertently... and procedure, Government procurement, Government property, Loan programs-business, Small businesses...

MICRO, SMALL AND MEDIUM-SIZED BUSINESSES IN JALISCO: THEIR EVOLUTION, AND STRATEGIC CHALLENGES

OpenAIRE

Carlos Fong Reynoso; Moisés Alejandro Alarcón Osuna; Luis Ernesto Ocampo Figueroa

2014-01-01

The business structure in Jalisco, Mexico is primarily composed of micro, small and medium-sized enterprises (SMEs). Thus, it is fundamentally necessary to understand the dynamics, evolution and above all, the strategic challenges of this sector in order to understand the state’s economic performance and the possibilities for future development in Jalisco. As a result, this study analyzes the evolution of the SMEs (known as PyME, in Spanish) in Mexico and Jalisco by using data from the Econom...

Robust Color Choice for Small-size League RoboCup Competition

Directory of Open Access Journals (Sweden)

Qiang Zhou

2004-10-01

Full Text Available In this paper, the problem of choosing a set of most separable colors in a given environment is discussed. The proposed method models the process of generating theoretically computed best colors, printing of these colors through a color printer, and imaging the printed colors through a camera into an integrated framework. Thus, it provides a feasible way to generate practically best separable colors for a given environment with a set of given equipment. A real world application (robust color choice for small-size league RoboCup competition is used as an example to illustrate the proposed method. Experimental results on this example show the competitiveness of the colors learned from our algorithm compared to the colors adopted by other teams which are chosen via an extensive trial and error process using standard color papers.

Visual SLAM and Moving-object Detection for a Small-size Humanoid Robot

Directory of Open Access Journals (Sweden)

Yin-Tien Wang

2010-09-01

Full Text Available In the paper, a novel moving object detection (MOD algorithm is developed and integrated with robot visual Simultaneous Localization and Mapping (vSLAM. The moving object is assumed to be a rigid body and its coordinate system in space is represented by a position vector and a rotation matrix. The MOD algorithm is composed of detection of image features, initialization of image features, and calculation of object coordinates. Experimentation is implemented on a small-size humanoid robot and the results show that the performance of the proposed algorithm is efficient for robot visual SLAM and moving object detection.

Simulation of Supply-Chain Networks: A Source of Innovation and Competitive Advantage for Small and Medium-Sized Enterprises

Directory of Open Access Journals (Sweden)

Giacomo Liotta

2012-11-01

Full Text Available On a daily basis, enterprises of all sizes cope with the turbulence and volatility of market demands, cost variability, and severe pressure from globally distributed competitors. Managing uncertainty about future demand requirements and volumes in supply-chain networks has become a priority. One of the ways to deal with uncertainty is the utilization of simulation techniques and tools, which provide greater predictability of decision-making outcomes. For example, simulation has been widely applied in decision-making processes related to global logistics and production networks at the strategic, tactical, and operational levels, where it is used to predict the impact of decisions before their implementation in complex and uncertain environments. Large enterprises are inclined to use simulation tools whereas small and medium-sized enterprises seem to underestimate its advantages. The objective of this article is to emphasize the relevance of simulation for the design and management of supply-chain networks from the perspective of small and medium-sized firms.

Atomistic Simulations of Small-scale Materials Tests of Nuclear Materials

International Nuclear Information System (INIS)

Shin, Chan Sun; Jin, Hyung Ha; Kwon, Jun Hyun

2012-01-01

Degradation of materials properties under neutron irradiation is one of the key issues affecting the lifetime of nuclear reactors. Evaluating the property changes of materials due to irradiations and understanding the role of microstructural changes on mechanical properties are required for ensuring reliable and safe operation of a nuclear reactor. However, high dose of neuron irradiation capabilities are rather limited and it is difficult to discriminate various factors affecting the property changes of materials. Ion beam irradiation can be used to investigate radiation damage to materials in a controlled way, but has the main limitation of small penetration depth in the length scale of micro meters. Over the past decade, the interest in the investigations of size-dependent mechanical properties has promoted the development of various small-scale materials tests, e.g. nanoindentation and micro/nano-pillar compression tests. Small-scale materials tests can address the issue of the limitation of small penetration depth of ion irradiation. In this paper, we present small-scale materials tests (experiments and simulation) which are applied to study the size and irradiation effects on mechanical properties. We have performed molecular dynamics simulations of nanoindentation and nanopillar compression tests. These atomistic simulations are expected to significantly contribute to the investigation of the fundamental deformation mechanism of small scale irradiated materials

Computer scientist looks at reliability computations

International Nuclear Information System (INIS)

Rosenthal, A.

1975-01-01

Results from the theory of computational complexity are applied to reliability computations on fault trees and networks. A well known class of problems which almost certainly have no fast solution algorithms is presented. It is shown that even approximately computing the reliability of many systems is difficult enough to be in this class. In the face of this result, which indicates that for general systems the computation time will be exponential in the size of the system, decomposition techniques which can greatly reduce the effective size of a wide variety of realistic systems are explored

Prevalence of advanced adenomas in small and diminutive colon polyps using direct measurement of size.

Science.gov (United States)

Tsai, Franklin C; Strum, Williamson B

2011-08-01

Most studies reporting polyp size use visual estimates. Determining the prevalence of advanced histology based on direct measurement of polyp size may help guide the management of polyps found at optical colonoscopy (OC) and CT colonography (CTC). We designed a large, prospective study to assess the prevalence of advanced adenomas based on direct measurement of polyp size by a certified pathologists' assistant as reported in the pathology report. Patients between 40 and 89 years of age who presented for screening colonoscopy were included in our study. Advanced adenomas were defined as ≥10 mm or ≥25% villous features, high grade dysplasia or cancer. Polyps were divided by size into three groups: diminutive (≤5 mm), small (6-9 mm) and large (≥10 mm). If more than one adenoma was present, the most advanced was used for analysis. We evaluated 6,905 consecutive patients referred for colonoscopy between January 2005 and December 2006. Of the 4,967 who met the inclusion criteria, the mean age was 58.8 and consisted of 59% women. Overall, 930 (18.7%) had an adenoma; 248 (5%) were advanced adenomas including 8 (0.16%) cancers. Of 89 polyps≥10 mm, 76 (85%) had advanced histology; of 247 polyps 6-9 mm, 67 (27%) were advanced; of 1,025 polyps ≤5 mm, 105 (10%) were advanced. Thus, 172 of 248 (69%) patients with advanced adenomas had small or diminutive adenomas. Our data indicate the majority (69%) of advanced adenomas are advanced adenomas (10%). These findings may help guide the management of sub-centimeter colon polyps found by OC or CTC.

Models on reliability of non-destructive testing

International Nuclear Information System (INIS)

Simola, K.; Pulkkinen, U.

1998-01-01

The reliability of ultrasonic inspections has been studied in e.g. international PISC (Programme for the Inspection of Steel Components) exercises. These exercises have produced a large amount of information on the effect of various factors on the reliability of inspections. The information obtained from reliability experiments are used to model the dependency of flaw detection probability on various factors and to evaluate the performance of inspection equipment, including the sizing accuracy. The information from experiments is utilised in a most effective way when mathematical models are applied. Here, some statistical models for reliability of non-destructive tests are introduced. In order to demonstrate the use of inspection reliability models, they have been applied to the inspection results of intergranular stress corrosion cracking (IGSCC) type flaws in PISC III exercise (PISC 1995). The models are applied to both flaw detection frequency data of all inspection teams and to flaw sizing data of one participating team. (author)

Moment Magnitudes of Small to Moderate Size Regional Events from Coda in the Middle East

Science.gov (United States)

Gok, R.; Pasyanos, M. E.; Matzel, E.; Mayeda, K. M.; Walter, W. R.

2010-12-01

The uneven distribution of stations and heterogeneous structure of the Middle East makes it difficult to calculate reliable moment magnitudes in the region. Such magnitudes are important for event characterization, and for yield estimation applications. The complex structure of the lithosphere in the region causes significant variation in the recorded amplitude of body and surface waves that travel along different paths. These 2-D effects are most significant for small and moderate magnitude events, which are most observable at periods 4.5) at low frequencies ( < 0.5 Hz). But even using coda waves, high frequency spectra show considerable scatter. Next, we applied tomographic inversion to the geometrical spreading corrected coda amplitudes to calculate 2-D coda Q. Coda Q results agree well with direct Lg and tectonics of the region. We observe low Q in Anatolian and Iranian plateaus and high Q in Arabian Plate. Applying the 2-D correction reduced the inter-station scatter of the higher frequency spectra, allowing us to obtain reliable moment magnitude estimates for smaller events (Mw < 4.5).

Cash flow vs. collateral-based credit: performance of micro, small and medium-sized firms in transition economies

Czech Academy of Sciences Publication Activity Database

Cassano, F.; Joeveer, K.; Švejnar, Jan

2013-01-01

Roč. 21, č. 2 (2013), s. 269-300 ISSN 0967-0750 Institutional support: RVO:67985998 Keywords : micro, small and medium-sized enterprises * bank credit * firm performance Subject RIV: AH - Economics Impact factor: 0.755, year: 2013

Airport level of service: A model according to departing passengers’ perceptions at a small-sized airport

Directory of Open Access Journals (Sweden)

Max Well Elias Gonçalves

2017-04-01

Full Text Available Purpose: This study proposes a conceptual model of level of service evaluation to a small-sized airport with a focus on departing passengers. Design/Methodology: The variables selected to compose the model were chosen according to their adequacy to departing passengers and the airport’s characteristics. A survey was conducted, and, posteriorly, exploratory factor analysis was used in order to verify the adequacy of the conceptual model proposed and also to improve it according to the results obtained. Findings: The results show that the level of service of the airport is composed of three dimensions: airport characteristics, passenger processing, and prices. The relative importance of the dimensions according to their contribution to the composition of the airport’s overall level of service was also determined. Originality/value: The paper combines theoretical and practical findings in a model for level of service evaluation to a small-sized airport from an air transportation management perspective.

Reliability of sprinkler systems. Exploration and analysis of data from nuclear and non-nuclear installations

International Nuclear Information System (INIS)

Roenty, V.; Keski-Rahkonen, O.; Hassinen, J.P.

2004-12-01

Sprinkler systems are an important part of fire safety of nuclear installations. As a part of effort to make fire-PSA of our utilities more quantitative a literature survey from open sources worldwide of available reliability data on sprinkler systems was carried out. Since the result of the survey was rather poor quantitatively, it was decided to mine available original Finnish nuclear and non-nuclear data, since nuclear power plants present a rather small device population. Sprinklers are becoming a key element for the fire safety in modern, open non-nuclear buildings. Therefore, the study included both nuclear power plants and non-nuclear buildings protected by sprinkler installations. Data needed for estimating of reliability of sprinkler systems were collected from available sources in Finnish nuclear and non-nuclear installations. Population sizes on sprinkler system installations and components therein as well as covered floor areas were counted individually from Finnish nuclear power plants. From non-nuclear installations corresponding data were estimated by counting relevant things from drawings of 102 buildings, and plotting from that sample needed probability distributions. The total populations of sprinkler systems and components were compiled based on available direct data and these distributions. From nuclear power plants electronic maintenance reports were obtained, observed failures and other reliability relevant data were selected, classified according to failure severity, and stored on spreadsheets for further analysis. A short summary of failures was made, which was hampered by a small sample size. From non-nuclear buildings inspection statistics from years 1985.1997 were surveyed, and observed failures were classified and stored on spreadsheets. Finally, a reliability model is proposed based on earlier formal work, and failure frequencies obtained by preliminary data analysis of this work. For a model utilising available information in the non

Reliability of four experimental mechanical pain tests in children

Directory of Open Access Journals (Sweden)

Soee AL

2013-02-01

Full Text Available Ann-Britt L Soee,1 Lise L Thomsen,2 Birte Tornoe,1,3 Liselotte Skov11Department of Pediatrics, Children’s Headache Clinic, Copenhagen University Hospital Herlev, Copenhagen, Denmark; 2Department of Neuropediatrics, Juliane Marie Centre, Copenhagen University Hospital Rigshospitalet, København Ø, Denmark; 3Department of Physiotherapy, Medical Department O, Copenhagen University Hospital Herlev, Herlev, DenmarkPurpose: In order to study pain in children, it is necessary to determine whether pain measurement tools used in adults are reliable measurements in children. The aim of this study was to explore the intrasession reliability of pressure pain thresholds (PPT in healthy children. Furthermore, the aim was also to study the intersession reliability of the following four tests: (1 Total Tenderness Score; (2 PPT; (3 Visual Analog Scale score at suprapressure pain threshold; and (4 area under the curve (stimulus–response functions for pressure versus pain.Participants and methods: Twenty-five healthy school children, 8–14 years of age, participated. Test 2, PPT, was repeated three times at 2 minute intervals on the same day to estimate PPT intrasession reliability using Cronbach’s alpha. Tests 1–4 were repeated after median 21 (interquartile range 10.5–22 days, and Pearson’s correlation coefficient was used to describe the intersession reliability.Results: The PPT test was precise and reliable (Cronbach’s alpha ≥ 0.92. All tests showed a good to excellent correlation between days (intersessions r = 0.66–0.81. There were no indications of significant systematic differences found in any of the four tests between days.Conclusion: All tests seemed to be reliable measurements in pain evaluation in healthy children aged 8–14 years. Given the small sample size, this conclusion needs to be confirmed in future studies.Keywords: repeatability, intraindividual reliability, pressure pain threshold, pain measurement, algometer

The APACHE survey hardware and software design: Tools for an automatic search of small-size transiting exoplanets

Directory of Open Access Journals (Sweden)

Lattanzi M.G.

2013-04-01

Full Text Available Small-size ground-based telescopes can effectively be used to look for transiting rocky planets around nearby low-mass M stars using the photometric transit method, as recently demonstrated for example by the MEarth project. Since 2008 at the Astronomical Observatory of the Autonomous Region of Aosta Valley (OAVdA, we have been preparing for the long-term photometric survey APACHE, aimed at finding transiting small-size planets around thousands of nearby early and mid-M dwarfs. APACHE (A PAthway toward the Characterization of Habitable Earths is designed to use an array of five dedicated and identical 40-cm Ritchey-Chretien telescopes and its observations started at the beginning of summer 2012. The main characteristics of the survey final set up and the preliminary results from the first weeks of observations will be discussed.

ENVIRONMENTAL RESPONSIBILITY OF SMALL AND MEDIUM-SIZED ENTERPRISES AND ITS SIGNIFICANCE FOR THE IMPLEMENTATION OF THE CSR CONCEPT

Directory of Open Access Journals (Sweden)

Magdalena Kaźmierczak

2016-06-01

Full Text Available This article attempts to assess the importance of the environmental dimension of the concept of corporate social responsibility (Social Corporate Responsibility - CSR in small and medium-sized enterprises. The first part describes the essence of corporate social responsibility. The second part is the basic pillar of CSR, which is an ecological area. The third part presents the environmental efforts undertaken by small and medium-sized enterprises in the field of CSR. The analysis was based on the literature available and data obtained from empirical research conducted by the writer. The results show that companies, however in different extent undertake ecological activities willingly. Furthermore, those activities benefit not only in terms of the environmental dimension of CSR, but also in other areas of the organization.

MACROECONOMIC CLIMATE AND THE SMALL AND MEDIUM SIZE COMPANIES IN ROMANIA

Directory of Open Access Journals (Sweden)

Andrei Rădulescu

2017-10-01

Full Text Available Small and medium size companies (SMEs represent the engine of the economy in the member states of the European Union. In Romania, SMEs entered the post-crisis cycle in 2013 after a severe adjustment process under the impact of the Great Recession. The economic performance of SMEs is strongly influenced by the macroeconomic climate. The important role of SMEs in the economy has determined the Romanian government to implement several measures in order to support their activity. The present paper highlights the mid-term macroeconomic outlook for Romania, as well as the recent developments related to SMEs, along with the main measures implemented by the Government over the past years in order to support the development of these companies.

Development of natural circulation small and medium sized boiling water reactor: HSBWR-600

International Nuclear Information System (INIS)

Miki, Minoru; Horiuchi, Tetsuo; Yoshimoto, Yuichiro; Sumida, Isao; Murase, Michio; Akita, Minoru; Niino, Tsuyoshi

1988-01-01

In nuclear power generation, the development of large reactors has been promoted as the main energy source in Japan. However, world economy entered low growth age, and the growth of electric power demand slowed down. Accordingly, attention has been paid to the medium and small reactors that can cope with whatever needs by serializing their types in addition to the nuclear power plants of medium output matching to electric power demand. In order to cope with these new needs, the economical efficiency of medium and small reactors must be as close as possible to that of large reactors, and as the countermeasures to the demerits due to small size, those must be made into the plants having simplified systems and the safety easily acceptable to public. Hitachi Ltd. plans to develop the natural circulation type medium and small BWRs of 600 NWe output class, HSBWR-600, on the basis of the nuclear power plant technology based on the rich results of design and operation of BWRs obtained so far, and to rank them as one of the BWR series. The target of their development design, the circumstance of their development, the core design and the thermo-hydraulic characteristics, the reactor pressure vessel and in-core structures, the safety design, system design, building layout and the evaluation are reported. (Kako, I.)

A framework for effective implementation of lean production in Small and Medium-sized Enterprises

Directory of Open Access Journals (Sweden)

Amine Belhadi

2016-09-01

Full Text Available Purpose: The present paper aims at developing an effective framework including all the components necessary for implementing lean production properly in Small and Medium-sized Enterprises. Design/methodology/approach: The paper begins with the review of the main existing framework of lean implementation in order to highlight shortcomings in the literature through a lack of suitable framework for small companies. To overcome this literature gap, data of successful initiatives of lean implementation were collected based on a multiple case study approach. These initiatives has been juxtaposed in order to develop a new, practical and effective framework that includes all the components (process, tools, success factors that are necessary to implement lean in Small and Medium-sized Enterprises. Findings: The proposed framework presents many significant contributions: First, it provides an overcoming for the limitations of the existing frameworks by proposing for consultants, researchers and organizations an effective framework for lean implementation in SMEs that allows SMEs to benefit from competitive advantages  gained by lean. Second, it brings together a set of the more essential and critical elements of lean implementation commonly used by SMEs and derived from the practical experiences of them in lean implementation. Finally, it highlights the successful experiences of small companies in implementing lean programs and then proves that lean can give a relevant results even for SMEs. Research limitations/implications: The proposed framework presents a number of limitations and still evokes extension for further researches: Although it was derived from practical experiences of SMEs, the proposed framework is not supported by practical implementation. On the other hand and even though the elements in the proposed framework from the practical experiences of four SMEs, the identified elements need to be generalized and enriching by conducting

Expansion And International Expansion Of Small-To Medium Sized Firms: The Role Of Finance

OpenAIRE

Jan Smolarski; Can Kut; Neil Wilner

2011-01-01

Small- to medium-sized firms are expected to show international growth at an early stage. Several factors may affect the outcome of initial efforts to expand and internationalize. Our research examines how equity based venture funding affects SME expansion and internationalization. We divide venture capital financing into two categories: incremental financing where firms receive their venture capital funding in portions and lump-sum venture funding where firms receive their funding in one lum...

Small and medium sized enterprises (SMEs) in international business: A survey of recent literature

OpenAIRE

Schmidt, Klaus-Dieter

1996-01-01

It is often argued that the process of globalization has mainly favoured large-scale multinational companies which are able to organize their business efficiently within internal hierarchies. However, globalization has not only pushed cross-border intra-finn transactions but also other arrangements among firms such as licensing or subcontracting that fall short of ownership involvements. This opens up new opportunities for small and medium sized enterprises, too. The paper provides a general ...

Market Potential Estimation of a Small and Medium Size Reactor

International Nuclear Information System (INIS)

Oh, K. B.; Yang, M. H.; Lee, M. K.; Chung, W. S.; Kim, H. J.; Kim, S. S.; Lee, B. W.; Ryu, J. S.; Juhn, P. E.

2004-12-01

Technically, nuclear reactors which produce energy in the form of heat can supply energy products other than electricity, including district heat, process heat, potable water etc. Currently non-civil uses of nuclear energy are very limited civil applications except for a military nuclear powered ship and an energy usage in isolated areas. However, the future global environment and an energy resources scarcity could promote a significant usage of non-electrical applications on an industrial scale. Considering these situations, this report analyzed the following: (1) Worldwide non-electrical application of a small and medium sized nuclear reactor - survey the situation of the current technical applications, - survey the global market potential estimation for various applications (2) Technical cooperation potential in several countries - identify necessary conditions for nuclear cooperation, - select candidate countries: Morocco, UAE, Indonesia, Chile and Vietnam, - survey the energy and water situation, - survey the legal and international regime infrastructure

Fatigue-crack propagation in gamma-based titanium aluminide alloys at large and small crack sizes

International Nuclear Information System (INIS)

Kruzic, J.J.; Campbell, J.P.; Ritchie, R.O.

1999-01-01

Most evaluations of the fracture and fatigue-crack propagation properties of γ+α 2 titanium aluminide alloys to date have been performed using standard large-crack samples, e.g., compact-tension specimens containing crack sizes which are on the order of tens of millimeters, i.e., large compared to microstructural dimensions. However, these alloys have been targeted for applications, such as blades in gas-turbine engines, where relevant crack sizes are much smaller ( 5 mm) and (c ≅ 25--300 microm) cracks in a γ-TiAl based alloy, of composition Ti-47Al-2Nb-2Cr-0.2B (at.%), specifically for duplex (average grain size approximately17 microm) and refined lamellar (average colony size ≅150 microm) microstructures. It is found that, whereas the lamellar microstructure displays far superior fracture toughness and fatigue-crack growth resistance in the presence of large cracks, in small-crack testing the duplex microstructure exhibits a better combination of properties. The reasons for such contrasting behavior are examined in terms of the intrinsic and extrinsic (i.e., crack bridging) contributions to cyclic crack advance

Methodological issues concerning the application of reliable laser particle sizing in soils

Science.gov (United States)

de Mascellis, R.; Impagliazzo, A.; Basile, A.; Minieri, L.; Orefice, N.; Terribile, F.

2009-04-01

During the past decade, the evolution of technologies has enabled laser diffraction (LD) to become a much widespread means of particle size distribution (PSD), replacing sedimentation and sieve analysis in many scientific fields mainly due to its advantages of versatility, fast measurement and high reproducibility. Despite such developments of the last decade, the soil scientist community has been quite reluctant to replace the good old sedimentation techniques (ST); possibly because of (i) the large complexity of the soil matrix inducing different types of artefacts (aggregates, deflocculating dynamics, etc.), (ii) the difficulties in relating LD results with results obtained through sedimentation techniques and (iii) the limited size range of most LD equipments. More recently LD granulometry is slowly gaining appreciation in soil science also because of some innovations including an enlarged size dynamic range (0,01-2000 m) and the ability to implement more powerful algorithms (e.g. Mie theory). Furthermore, LD PSD can be successfully used in the application of physically based pedo-transfer functions (i.e., Arya and Paris model) for investigations of soil hydraulic properties, due to the direct determination of PSD in terms of volume percentage rather than in terms of mass percentage, thus eliminating the need to adopt the rough approximation of a single value for soil particle density in the prediction process. Most of the recent LD work performed in soil science deals with the comparison with sedimentation techniques and show the general overestimation of the silt fraction following a general underestimation of the clay fraction; these well known results must be related with the different physical principles behind the two techniques. Despite these efforts, it is indeed surprising that little if any work is devoted to more basic methodological issues related to the high sensitivity of LD to the quantity and the quality of the soil samples. Our work aims to

SMALL GRAIN 1, which encodes a mitogen-activated protein kinase kinase 4, influences grain size in rice.

Science.gov (United States)

Duan, Penggen; Rao, Yuchun; Zeng, Dali; Yang, Yaolong; Xu, Ran; Zhang, Baolan; Dong, Guojun; Qian, Qian; Li, Yunhai

2014-02-01

Although grain size is one of the most important components of grain yield, little information is known about the mechanisms that determine final grain size in crops. Here we characterize rice small grain1 (smg1) mutants, which exhibit small and light grains, dense and erect panicles and comparatively slightly shorter plants. The short grain and panicle phenotypes of smg1 mutants are caused by a defect in cell proliferation. The smg1 mutations were identified, using a map-based cloning approach, in mitogen-activated protein kinase kinase 4 (OsMKK4). Relatively higher expression of OsMKK4/SMG1 was detected in younger organs than in older ones, consistent with its role in cell proliferation. Green fluorescent protein (GFP)-OsMKK4/SMG1 fusion proteins appear to be distributed ubiquitously in plant cells. Further results revealed that OsMKK4 influenced brassinosteroid (BR) responses and the expression of BR-related genes. Thus, our findings have identified OsMKK4 as a factor for grain size, and suggest a possible link between the MAPK pathways and BRs in grain growth. © 2013 The Authors The Plant Journal © 2013 John Wiley & Sons Ltd.

Flowering and fruiting intensity of small - sized tomato, due to the regulation of the quantity of light reaching the plant top

Directory of Open Access Journals (Sweden)

Renata Dobromilska

2012-12-01

Full Text Available The experiments were carried out in 2001-2003 in a high unheated plastic tunnel. The influence of reduction of leaves and application of reflection matter on flowering and fruiting of small-sized tomato was studied. The experiment focused on the following factors: methods of increasing the amount of light in plant tops (reflection matter, cutting leaves, reflection matter + cutting leaves and cultivars of small sized tomato ('Conchita F1', 'Picolino F1'. The cutting of leaves and reflection matter mulching resulted in the increase of the intensity of radiation reaching plant tops and the reflected radiation. The above measures increasing the light access to plant tops significantly increased the number of flowers, germs and fruits. The reflection matter mulching along with cutting leaves resulted in the substantial growth of early yield of small-sized tomato. The 'Conchita F1' cultivar set a relatively greater number of flowers and fruits on a plant and in cluster than 'Picolino F1'.

Size and importance of small electrical end uses in households

Energy Technology Data Exchange (ETDEWEB)

Broderick, J R; Zogg, R A; Alberino, D L

1998-07-01

Miscellaneous end uses (an energy-consumption category in the residential sector) has recently emerged with more importance than ever before. Miscellaneous end uses are a collection of numerous end uses (often unrelated in technology or market characteristics) that individually are small consumers but when grouped together can become notable in size. The Annual Energy Outlook 1998, published by the Energy Information Administration (EIA), suggests that about 32% of residential electricity use in 1996 is attributable to miscellaneous end uses (21% from the Other Uses category and 11% from other miscellaneous categories). The EIA predicts this consumption will grow to about 47% of residential electricity use by 2010. Other studies have shown substantial consumption in this category, and forecast substantial future growth as well. However, it is not clear that the current accounting structure of the miscellaneous category is the most appropriate one, nor that the forecast growth in consumption will materialize. A bottom-up study on a collection of miscellaneous electric end uses was performed to better understand this complex, ill-defined category. Initial results show that many end uses can be categorized more appropriately, such as furnace fans, which belong in Space Heating. A recommended categorization reduces the Other Uses category from 21% to 12% of electric consumption estimated in 1996. Thus, the consumption from miscellaneous end uses is not nearly as large as thought. Furthermore, the growth rate associated with small end uses is projected to be lower relative to projections from other sources.

Reliability assessment of embedded digital system using multi-state function

International Nuclear Information System (INIS)

Choi, Jong Gyun; Seong, Poong Hyun

2006-01-01

This work describes a combinatorial model for estimating the reliability of the embedded digital system by means of multi-state function. This model includes a coverage model for fault-handling techniques implemented in digital systems. The fault-handling techniques make it difficult for many types of components in digital system to be treated as binary state, good or bad. The multi-state function provides a complete analysis of multi-state systems as which the digital systems can be regarded. Through adaptation of software operational profile flow to multi-state function, the HW/SW interaction is also considered for estimation of the reliability of digital system. Using this model, we evaluate the reliability of one board controller in a digital system, Interposing Logic System (ILS), which is installed in YGN nuclear power units 3 and 4. Since the proposed model is a generalized combinatorial model, the simplification of this model becomes the conventional model that treats the system as binary state. This modeling method is particularly attractive for embedded systems in which small sized application software is implemented since it will require very laborious work for this method to be applied to systems with large software

Small Lesion Size Is Associated with Sleep-Related Epilepsy in Focal Cortical Dysplasia Type II

Directory of Open Access Journals (Sweden)

Bo Jin

2018-02-01

Full Text Available ObjectiveTo investigate the neuroimaging and clinical features associated with sleep-related epilepsy (SRE in patients with focal cortical dysplasia (FCD type II.MethodsPatients with histopathologically proven FCD type II were included from three epilepsy centers. SRE was defined according to the video EEG findings and seizure history. Cortical surface reconstruction and volume calculation were performed using FreeSurfer. The lesions were manually delineated on T1 volumetric MRI using the ITK-SNAP software. The lesion volumes were normalized by the intracranial volume of each patient. The lesions were classified as small or large by placing a threshold based on quantitative (whether the lesion was detected on MRI report and qualitative (volume criteria.ResultsA total of 77 consecutive patients were included. Of them, 36 had SRE and 41 had non-SRE. An earlier age of epilepsy onset, high seizure frequency, regional interictal EEG findings, and favorable surgical outcome were characteristic in both groups. Small lesions were defined as those having a volume <3,217 mm3. In total, 60.9% of the patients with SRE (25/41 had small FCD lesion, which was significantly higher than the non-SRE group (9/34, 26.5%, p = 0.005. Small lesion size was the only predictor significantly associated with SRE in the overall type II group by multivariate analyses (p = 0.016. Although the proportion of patients who had frontal FCD and SRE was higher than non-frontal FCD (54.5 vs. 27.3%, p = 0.043, the relationship between SRE and lesion location was not confirmed by multivariate analysis. Thalamic volume and seizure semiology were not statistically different between the SRE and non-SRE group. The significant association between lesion size and SRE was reproducible in type IIb and IIa subgroups.SignificanceSRE is common in patients with FCD type II. Small FCD type II lesions are significantly associated with SRE. Although our findings cannot be applied to

Association of prenatal phenobarbital and phenytoin exposure with small head size at birth and with learning problems

NARCIS (Netherlands)

Dessens, A. B.; Cohen-Kettenis, P. T.; Mellenbergh, G. J.; Koppe, J. G.; van de Poll, N. E.; Boer, K.

2000-01-01

Small head size has been observed in prenatally anticonvulsant-exposed neonates. In infancy, cognitive impairments were revealed. It is presently unknown whether these impairments are permanent or disappear after puberty. We studied the link between the prenatal influence of anticonvulsants on brain

Method for assessing reliability of a network considering probabilistic safety assessment

International Nuclear Information System (INIS)

Cepin, M.

2005-01-01

A method for assessment of reliability of the network is developed, which uses the features of the fault tree analysis. The method is developed in a way that the increase of the network under consideration does not require significant increase of the model. The method is applied to small examples of network consisting of a small number of nodes and a small number of their connections. The results give the network reliability. They identify equipment, which is to be carefully maintained in order that the network reliability is not reduced, and equipment, which is a candidate for redundancy, as this would improve network reliability significantly. (author)