Finding Relevant Parameters for the Thin-film Photovoltaic Cells Production Process with the Application of Data Mining Methods.

Science.gov (United States)

Ulaczyk, Jan; Morawiec, Krzysztof; Zabierowski, Paweł; Drobiazg, Tomasz; Barreau, Nicolas

2017-09-01

A data mining approach is proposed as a useful tool for the control parameters analysis of the 3-stage CIGSe photovoltaic cell production process, in order to find variables that are the most relevant for cell electric parameters and efficiency. The analysed data set consists of stage duration times, heater power values as well as temperatures for the element sources and the substrate - there are 14 variables per sample in total. The most relevant variables of the process have been found based on the so-called random forest analysis with the application of the Boruta algorithm. 118 CIGSe samples, prepared at Institut des Matériaux Jean Rouxel, were analysed. The results are close to experimental knowledge on the CIGSe cells production process. They bring new evidence to production parameters of new cells and further research. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Modelling of interplanetary pickup ion fluxes and relevance for LISM parameters

International Nuclear Information System (INIS)

Fahr, H.J.; Rucinski, D.

1989-01-01

It has been known for many years that neutral interstellar atoms enter the solar system from the upwind side and penetrate deep into the inner heliosphere. Helium atoms, in particular, advance towards very small solar distances before they are ionized and then again convected as He - pickup ions outwards with the solar wind. Since these ions were recently detected in space, we concentrate here on calculations of He + production rates and He + fluxes. It is shown that inside 1 a.u., the He - production is essentially determined both by solar e.u.v. photoionization and by electron impact ionization. We calculate He + production rates as a function of space coordinates, taking into account the core-halo structure of the energy distribution of solar wind electrons and their temperature distribution with distance according to relevant solar wind models. For this purpose, a newly developed program to compute He densities was used. In contrast to the production of H + , the He - production rates are found to be higher on the downwind axis than on the upwind axis by a factor of 5. We also determine partial and total He + ion fluxes as a function of solar distance and longitude. It is interesting to note that only the values for total fluxes agree well with the integrated He + fluxes measured by the SULEICA experiment aboard the AMPTE satellite. This indicates that pickup ions under the influence of the intrinsic MHD wave turbulence in the solar wind change their primary seed distribution function by rapid pitch-angle scattering and subsequent adiabatic cooling. To interpret the He + intensity profile along the orbit of the Earth in terms of LISM helium parameters, we point to the need to take into account carefully electron impact ionization in order to prevent misinterpretations. (author)

Safety analysis methodology with assessment of the impact of the prediction errors of relevant parameters

International Nuclear Information System (INIS)

Galia, A.V.

2011-01-01

The best estimate plus uncertainty approach (BEAU) requires the use of extensive resources and therefore it is usually applied for cases in which the available safety margin obtained with a conservative methodology can be questioned. Outside the BEAU methodology, there is not a clear approach on how to deal with the issue of considering the uncertainties resulting from prediction errors in the safety analyses performed for licensing submissions. However, the regulatory document RD-310 mentions that the analysis method shall account for uncertainties in the analysis data and models. A possible approach is presented, that is simple and reasonable, representing just the author's views, to take into account the impact of prediction errors and other uncertainties when performing safety analysis in line with regulatory requirements. The approach proposes taking into account the prediction error of relevant parameters. Relevant parameters would be those plant parameters that are surveyed and are used to initiate the action of a mitigating system or those that are representative of the most challenging phenomena for the integrity of a fission barrier. Examples of the application of the methodology are presented involving a comparison between the results with the new approach and a best estimate calculation during the blowdown phase for two small breaks in a generic CANDU 6 station. The calculations are performed with the CATHENA computer code. (author)

Influence of simulation assumptions and input parameters on energy balance calculations of residential buildings

International Nuclear Information System (INIS)

Dodoo, Ambrose; Tettey, Uniben Yao Ayikoe; Gustavsson, Leif

2017-01-01

In this study, we modelled the influence of different simulation assumptions on energy balances of two variants of a residential building, comprising the building in its existing state and with energy-efficient improvements. We explored how selected parameter combinations and variations affect the energy balances of the building configurations. The selected parameters encompass outdoor microclimate, building thermal envelope and household electrical equipment including technical installations. Our modelling takes into account hourly as well as seasonal profiles of different internal heat gains. The results suggest that the impact of parameter interactions on calculated space heating of buildings is somewhat small and relatively more noticeable for an energy-efficient building in contrast to a conventional building. We find that the influence of parameters combinations is more apparent as more individual parameters are varied. The simulations show that a building's calculated space heating demand is significantly influenced by how heat gains from electrical equipment are modelled. For the analyzed building versions, calculated final energy for space heating differs by 9–14 kWh/m"2 depending on the assumed energy efficiency level for electrical equipment. The influence of electrical equipment on calculated final space heating is proportionally more significant for an energy-efficient building compared to a conventional building. This study shows the influence of different simulation assumptions and parameter combinations when varied simultaneously. - Highlights: • Energy balances are modelled for conventional and efficient variants of a building. • Influence of assumptions and parameter combinations and variations are explored. • Parameter interactions influence is apparent as more single parameters are varied. • Calculated space heating demand is notably affected by how heat gains are modelled.

How cyclophosphamide at environmentally relevant concentration influences Daphnia magna life history and its proteome.

Directory of Open Access Journals (Sweden)

Małgorzata Grzesiuk

Full Text Available The waste of commonly used medicines is known to contaminate freshwater ecosystems. Pharmaceuticals can be toxic, mutagenic, or modifying to freshwater organisms even at low concentrations if consider their permanent presence in the environment. Chemotherapeutics used to treat cancer, and in particular alkylating agents, contribute significantly to this form of pollution, the latter introducing cytotoxic and/or mutagenic lesions to the DNA and RNA of organisms which can be disruptive to their cells. The aim of the present study was to investigate the influence of the alkylating anticancer agent cyclophosphamide (CP on Daphnia magna clones. We evaluated the life history parameters and protein profiles of this crustacean following exposure to environmentally relevant CP concentration of 10 ng L-1. Even at this low concentration, the alkylating agent caused modification of the life history parameters and proteome profile of the Daphnia. These changes were clone-specific and involved growth rate, age at first reproduction, neonate number, and proteins related to cell cycle and redox state regulation. The disturbance caused by pharmaceuticals contaminating freshwater ecosystem is probably weaker and unlikely to be cytotoxic in character due to the high dilution of these substances in the water. However, our results indicate that prolonged exposure of organisms to these toxins may lead to modifications on the organismal and molecular levels with unpredictable significance for the entire ecosystem.

Influence of steam parameters on static and dynamic characteristics of labyrinth seal

Directory of Open Access Journals (Sweden)

HE Wenqiang

2017-10-01

Full Text Available [Objectives] In order to study the influence of working medium parameters on the static and dynamic characteristics of seals in turbomachinery,[Methods] a three-dimensional model of a labyrinth seal was created, and air and steam were applied in the numerical simulation. The Computational Fluid Dynamics (CFD method and a rotating frame were applied to analyze the influence of different steam parameters on the leakage characteristics and dynamic characteristic coefficients.[Results] The results show that great differences in leakage flow rate are apparent under different air and steam conditions, and the fluid-induced force shows linear and nonlinear variation with the increasing whirl speed. When the steam temperature increases, the system stability decreases as the dynamic characteristic coefficients change.[Conclusions] In consequence, working medium parameters are of great significance for turbine stability, and the influence of working medium parameters on the static and dynamic characteristics of seals should be given great attention in practical application.

Influence of Extraction Parameters on Hydroalcohol Extracts of the ...

African Journals Online (AJOL)

The parameter that had the greatest influence on extraction process was alcohol concentration ... rules and processing steps [2]. As part .... Table 1: Extractive batch nnumbers with the respective factors and levels studied in the factorial design.

Process parameter influence on Electro-sinter-forging (ESF) of titanium discs

DEFF Research Database (Denmark)

Cannella, Emanuele; Nielsen, Chris Valentin; Bay, Niels

Electro-sinter-forging (ESF) is a sintering process based on the resistance heating principle, which makes it faster than conventional sintering. The process is investigated as a function of the main process parameters, namely compacting pressure, electrical current density and sintering time....... The present work is focused on analysing the influence of these process parameters on the final density of a disc sample made from commercially pure titanium powder. Applying the design of experiments (DoE) approach, the electrical current was seen to be of largest influence. The maximum obtained density...

Influence of roughness parameters on coefficient of friction under ...

Indian Academy of Sciences (India)

S¯adhan¯a Vol. 33, Part 3, June 2008, pp. ... Surface texture and thus roughness parameters influence coefficient of friction during sliding. ..... tural irregularities and complexities of the natural system, fractal is widely used to explain the natural ...

The influence of bread improvers and different technological parameters on bread quality

OpenAIRE

Duobienė, Lina

2015-01-01

Goal of the research: to analyse quality parameters of different types of bread, produced with or without improvers, also to evaluate intensity of microbiological spoilage of bread during storage. Results and findings: Different bread technologies have influence on bread quality parameters and in all cases bread improvers have positive influence on bread quality: „Lietuviškas ragaišis“ (Lithuanian whole wheat bread) using improvers the higher specific volume (21.27%) and porosity (9.02%...

Estimation of Medium Voltage Cable Parameters for PD Detection

DEFF Research Database (Denmark)

Villefrance, Rasmus; Holbøll, Joachim T.; Henriksen, Mogens

1998-01-01

Medium voltage cable characteristics have been determined with respect to the parameters having influence on the evaluation of results from PD-measurements on paper/oil and XLPE-cables. In particular, parameters essential for discharge quantification and location were measured. In order to relate...... and phase constants. A method to estimate this propagation constant, based on high frequency measurements, will be presented and will be applied to different cable types under different conditions. The influence of temperature and test voltage was investigated. The relevance of the results for cable...

Probability of detection as a function of multiple influencing parameters

Energy Technology Data Exchange (ETDEWEB)

Pavlovic, Mato

2014-10-15

Non-destructive testing is subject to measurement uncertainties. In safety critical applications the reliability assessment of its capability to detect flaws is therefore necessary. In most applications, the flaw size is the single most important parameter that influences the probability of detection (POD) of the flaw. That is why the POD is typically calculated and expressed as a function of the flaw size. The capability of the inspection system to detect flaws is established by comparing the size of reliably detected flaw with the size of the flaw that is critical for the structural integrity. Applications where several factors have an important influence on the POD are investigated in this dissertation. To devise a reliable estimation of the NDT system capability it is necessary to express the POD as a function of all these factors. A multi-parameter POD model is developed. It enables POD to be calculated and expressed as a function of several influencing parameters. The model was tested on the data from the ultrasonic inspection of copper and cast iron components with artificial flaws. Also, a technique to spatially present POD data called the volume POD is developed. The fusion of the POD data coming from multiple inspections of the same component with different sensors is performed to reach the overall POD of the inspection system.

Probability of detection as a function of multiple influencing parameters

International Nuclear Information System (INIS)

Pavlovic, Mato

2014-01-01

Non-destructive testing is subject to measurement uncertainties. In safety critical applications the reliability assessment of its capability to detect flaws is therefore necessary. In most applications, the flaw size is the single most important parameter that influences the probability of detection (POD) of the flaw. That is why the POD is typically calculated and expressed as a function of the flaw size. The capability of the inspection system to detect flaws is established by comparing the size of reliably detected flaw with the size of the flaw that is critical for the structural integrity. Applications where several factors have an important influence on the POD are investigated in this dissertation. To devise a reliable estimation of the NDT system capability it is necessary to express the POD as a function of all these factors. A multi-parameter POD model is developed. It enables POD to be calculated and expressed as a function of several influencing parameters. The model was tested on the data from the ultrasonic inspection of copper and cast iron components with artificial flaws. Also, a technique to spatially present POD data called the volume POD is developed. The fusion of the POD data coming from multiple inspections of the same component with different sensors is performed to reach the overall POD of the inspection system.

Influence of intensity parameters of earthquake on response of reinforced concrete structures

Science.gov (United States)

Cherian, Ciby Jacob; Madhavan Pillai, T. M.; Sajith, A. S.

2018-03-01

Earthquake is one of the most frightening and destructive phenomena of nature. The destructive capacity of an earthquake depends on various parameters. Without characterising earthquake time history data to the required intensity parameters, its effect on structures cannot be predicted. The influence of intensity parameter of earthquake on the destructive capacity of a structure is essential in the vibration control scenario also. In the present paper, three reinforced concrete (RC) framed structures with natural frequencies 4.688 Hz, 1.762 Hz, 1.661 Hz are used to investigate the influence between the intensity measures and the response. 20 ground motion time history data were selected with predominant frequency ranging from 1 Hz to 12.5 Hz. Some available intensity measures were used to characterise this data. 3D model of the structure was analysed in ETABSUL 13.1.3 software with diaphragm rigidity at floor level. Modal analysis was used to find the modes and corresponding time periods. Linear time history analysis was done for the three models for all the ground motion data. It is noted that four intensity parameters namely predominant frequency, Peak Ground Acceleration, Velocity Spectrum Intensity, Housner Intensity has an appreciable influence on the response.

Parameters Influencing Wave Run-Up on a Rubble Mound Breakwater

DEFF Research Database (Denmark)

Walle, Björn Van de; Rouck, Julien De; Damme, Luc Van

2002-01-01

been carried out on a slightly modified scale model: a regular armour unit pattern has been applied in stead of an irregular pattern as in full scale. The aim of the additional laboratory tests was to investigate the influence of the spectral width parameter and the influence of the position...... of the wave run-up step gauge with respect to the armour unit pattern and the water level....

The influence of source term release parameters on health effects

International Nuclear Information System (INIS)

Jeong, Jong Tae; Ha, Jae Joo

1998-08-01

In this study, the influence of source term release parameters on the health effects was examined. This is very useful in identifying the relative importance of release parameters and can be an important factor in developing a strategy for reducing offsite risks. The release parameters investigated in this study are release height, heat content, fuel burnup, release time, release duration, and warning time. The health effects affected by the change of release parameters are early fatalities, cancer fatalities, early injuries, cancer injuries, early fatality risk, population weighted early fatality risk, population weighted cancer fatality risk, effective whole body population dose, population exceeding an early acute red bone marrow dose of 1.5 Sv, and distance at which early fatalities are expected to occur. As release height increases, the values of early health effects such as early fatalities and injuries decrease. However, the release height dose not have significant influences on late health effects. The values of both early and late health effects decrease as heat content increases. The increase fuel burnup, i.e., the increase of core inventories increases the late health effects, however, has small influence on the early health effects. But, the number of early injuries increases as the fuel burnup increases. The effects of release time increase shows very similar influence on both the early and late health effects. As the release time increases to 2 hours, the values of health effects increase and then decrease rapidly. As release duration increases, the values of late health effects increase slightly, however, the values of early health effects decrease. As warning time increases to 2 hours, the values of late health effects decrease and then shows no variation. The number of early injuries decreases rapidly as the warning time increases to 2 hours. However, the number of early fatalities and the early fatality risk increase as the warning time increases

Transient Oscilliations in Mechanical Systems of Automatic Control with Random Parameters

Science.gov (United States)

Royev, B.; Vinokur, A.; Kulikov, G.

2018-04-01

Transient oscillations in mechanical systems of automatic control with random parameters is a relevant but insufficiently studied issue. In this paper, a modified spectral method was applied to investigate the problem. The nature of dynamic processes and the phase portraits are analyzed depending on the amplitude and frequency of external influence. It is evident from the obtained results, that the dynamic phenomena occurring in the systems with random parameters under external influence are complex, and their study requires further investigation.

Kinematic parameters that influence the aesthetic perception of beauty in contemporary dance.

Science.gov (United States)

Torrents, Carlota; Castañer, Marta; Jofre, Toni; Morey, Gaspar; Reverter, Ferran

2013-01-01

Some experiments have stablished that certain kinematic parameters can influence the subjective aesthetic perception of the dance audience. Neave, McCarty, Freynik, Caplan, Hönekopp, and Fink (2010, Biology Letters 7 221-224) reported eleven movement parameters in non-expert male dancers, showing a significant positive correlation with perceived dance quality. We aim to identify some of the kinematic parameters of expert dancers' movements that influence the subjective aesthetic perception of observers in relation to specific skills of contemporary dance. Four experienced contemporary dancers performed three repetitions of four dance-related motor skills. Motion was captured by a VICON-MX system. The resulting 48 animations were viewed by 108 observers. The observers judged beauty using a semantic differential. The data were then subjected to multiple factor analysis. The results suggested that there were strong associations between higher beauty scores and certain kinematic parameters, especially those related to amplitude of movement.

Identifying tectonic parameters that influence tsunamigenesis

Science.gov (United States)

van Zelst, Iris; Brizzi, Silvia; van Dinther, Ylona; Heuret, Arnauld; Funiciello, Francesca

2017-04-01

The role of tectonics in tsunami generation is at present poorly understood. However, the fact that some regions produce more tsunamis than others indicates that tectonics could influence tsunamigenesis. Here, we complement a global earthquake database that contains geometrical, mechanical, and seismicity parameters of subduction zones with tsunami data. We statistically analyse the database to identify the tectonic parameters that affect tsunamigenesis. The Pearson's product-moment correlation coefficients reveal high positive correlations of 0.65 between, amongst others, the maximum water height of tsunamis and the seismic coupling in a subduction zone. However, these correlations are mainly caused by outliers. The Spearman's rank correlation coefficient results in more robust correlations of 0.60 between the number of tsunamis in a subduction zone and subduction velocity (positive correlation) and the sediment thickness at the trench (negative correlation). Interestingly, there is a positive correlation between the latter and tsunami magnitude. In an effort towards multivariate statistics, a binary decision tree analysis is conducted with one variable. However, this shows that the amount of data is too scarce. To complement this limited amount of data and to assess physical causality of the tectonic parameters with regard to tsunamigenesis, we conduct a numerical study of the most promising parameters using a geodynamic seismic cycle model. We show that an increase in sediment thickness on the subducting plate results in a shift in seismic activity from outerrise normal faults to splay faults. We also show that the splay fault is the preferred rupture path for a strongly velocity strengthening friction regime in the shallow part of the subduction zone, which increases the tsunamigenic potential. A larger updip limit of the seismogenic zone results in larger vertical surface displacement.

Influence on muscle oxygenation to EMG parameters at different skeletal muscle contraction

Science.gov (United States)

Zhang, Li; Song, Gaoqing

2010-02-01

The purpose of this study is to investigate the influence of muscle oxygenation on EMG parameters during isometric and incremental exercises and to observe the relationship between EMG parameters and muscle oxygenation. Twelve rowers took part in the tests. Near infrared spectrometer was utilized for measurements of muscle oxygenation on lateral quadriceps. sEMG measurement is performed for EMG parameters during isometric and incremental exercises. Results indicated that Oxy-Hb decrease significantly correlated with IEMG, E/T ratio and frequency of impulse signal during 1/3 MVC and 2/3 MVC isometric exercise, and it is also correlated with IEMG, E/T ratio and frequency of impulse signal. Increase of IEMG occurred at the time after Oxy-Hb decrease during incremental exercise and highly correlated with BLa. It is concluded that no matter how heavy the intensity is, Oxy-Hb dissociation may play an important role in affecting EMG parameters of muscle fatigue during isometric exercise. 2) EMG parameters may be influenced by Oxy-Hb dissociation and blood lactate concentration during dynamic exercise.

Influence of Environmental Parameters on Trichoderma Strains with Biocontrol Potential

Directory of Open Access Journals (Sweden)

Zsuzsanna Antal

2003-01-01

Full Text Available Several mycoparasitic strains belonging to the filamentous fungal genus Trichoderma are promising candidates for the biological control of plant pathogenic fungi. When planning the application of antagonistic Trichoderma strains for the purposes of biological control, it is very important to consider the environmental parameters affecting the biocontrol agents in the soil. A series of abiotic and biotic environmental parameters has an influence on the biocontrol efficacy of Trichoderma. Some important parameters to be considered are the effects of temperature, water potential and pH, and the presence of pesticides, metal ions and antagonistic bacteria in the soil. Most of the Trichoderma strains are mesophilic. Low temperatures in winter may cause a problem during biological control by influencing the activity of the biocontrol agents. Another problem emerging during the application of Trichoderma strains as biocontrol agents is that they cannot tolerate dry conditions, however, we may need biocontrol agents against plant pathogenic fungi which are able to grow and cause disease even in dry soils. The pH characteristics of the soil also belong to the most important environmental parameters affecting the activities of mycoparasitic Trichoderma strains. Within the frames of a complex integrated plant protection strategy, we may have to combine Trichoderma strains with chemical pesticides or metal compounds, therefore it is important to collect information about the effects of pesticides and metal ions on the biocontrol strains. Antagonistic soil bacteria may also have negative effects on the biocontrol abilities of Trichoderma strains, therefore it may be advantageous if a biocontrol strain possesses bacterium- degrading abilities as well. This review will discuss the literature about the influence of temperature, water potential, pH, pesticides, metal ions and antagonistic bacteria on mycoparasitic Trichoderma strains including the results of our

Evaluation of the influence of acquisition parameters of microtomography in image quality applied by carbonate rocks

Science.gov (United States)

Santos, T. M. P.; Machado, A. S.; Araújo, O. M. O.; Ferreira, C. G.; Lopes, R. T.

2018-03-01

X-ray computed microtomography is a powerful nondestructive technique for 2D and 3D structure analysis. However, parameters used in acquisition promote directs influence in qualitative and quantitative results in characterization of samples, due image resolution. The aim of this study is value the influence of theses parameters in results through of tests changing these parameters in different situations and system characterization. Results demonstrate those pixel size and detector matrixes are the main parameters that influence in resolution and image quality. Microtomography was considered an excellent technique for characterization using the best image resolution possible.

Application of grey system theory on the influencing parameters of aerobic granulation in SBR.

Science.gov (United States)

Bindhu, B K; Madhu, G

2017-09-01

Aerobic granulation is a promising technology for wastewater treatment. Four operational parameters were selected as influencing factors for this study. Aerobic granulation was experimented with three different values of organic loading rate (3, 6 and 9 kg COD m -3  d -1 ), superficial upflow air velocity (SUAV) (2, 3 and 4 cm s -1 ), settling time (3, 5 and 10 min) and volume exchange ratio (25%, 50% and 75%) in sequencing batch reactor in nine trials for the optimal performance of aerobic granulation. The influence of compared parameters on five reference parameters (sludge volume index (SVI), time taken for the appearance of granules, size and specific gravity of granules and chemical oxygen demand (COD) removal) was analyzed using grey system theory. The grey relational coefficients and grey entropy relational grade of each parameter were calculated. Hydrodynamic shear force in terms of SUAV was found to have the greatest influence on granule appearance, specific gravity of granules and COD removal efficiency. SVI is greatly affected by settling time. The optimal scopes of all the compared parameters were found.

Effect of nonlinear void reactivity on bifurcation characteristics of a lumped-parameter model of a BWR: A study relevant to RBMK

Energy Technology Data Exchange (ETDEWEB)

Verma, Dinkar, E-mail: dinkar@iitk.ac.in [Nuclear Engineering and Technology Program, Indian Institute of Technology Kanpur, Kanpur 208 016 (India); Kalra, Manjeet Singh, E-mail: drmanjeet.singh@dituniversity.edu.in [DIT University, Dehradun 248 009 (India); Wahi, Pankaj, E-mail: wahi@iitk.ac.in [Department of Mechanical Engineering, Indian Institute of Technology Kanpur, Kanpur 208 016 (India)

2017-04-15

Highlights: • A simplified model with nonlinear void reactivity feedback is studied. • Method of multiple scales for nonlinear analysis and oscillation characteristics. • Second order void reactivity dominates in determining system dynamics. • Opposing signs of linear and quadratic void reactivity enhances global safety. - Abstract: In the present work, the effect of nonlinear void reactivity on the dynamics of a simplified lumped-parameter model for a boiling water reactor (BWR) is investigated. A mathematical model of five differential equations comprising of neutronics and thermal-hydraulics encompassing the nonlinearities associated with both the reactivity feedbacks and the heat transfer process has been used. To this end, we have considered parameters relevant to RBMK for which the void reactivity is known to be nonlinear. A nonlinear analysis of the model exploiting the method of multiple time scales (MMTS) predicts the occurrence of the two types of Hopf bifurcation, namely subcritical and supercritical, leading to the evolution of limit cycles for a range of parameters. Numerical simulations have been performed to verify the analytical results obtained by MMTS. The study shows that the nonlinear reactivity has a significant influence on the system dynamics. A parametric study with varying nominal reactor power and operating conditions in coolant channel has also been performed which shows the effect of change in concerned parameter on the boundary between regions of sub- and super-critical Hopf bifurcations in the space constituted by the two coefficients of reactivities viz. the void and the Doppler coefficient of reactivities. In particular, we find that introduction of a negative quadratic term in the void reactivity feedback significantly increases the supercritical region and dominates in determining the system dynamics.

Influence of newly designed monorail pressure sensor catheter on coronary diagnostic parameters: an in vitro study.

Science.gov (United States)

Banerjee, Rupak K; Peelukhana, Srikara V; Goswami, Ishan

2014-02-07

The decision to perform intervention on a patient with coronary stenosis is often based on functional diagnostic parameters obtained from pressure and flow measurements using sensor-tipped guidewire at maximal vasodilation (hyperemia). Recently, a rapid exchange Monorail Pressure Sensor catheter of 0.022″ diameter (MPS22), with pressure sensor at distal end has been developed for improved assessment of stenosis severity. The hollow shaft of the MPS22 is designed to slide over any standard 0.014″ guidewire (G14). Hence, influence of MPS22 diameter on coronary diagnostic parameters needs investigation. An in vitro experiment was conducted to replicate physiologic flows in three representative area stenosis (AS): mild (64% AS), intermediate (80% AS), and severe (90% AS), for two arterial diameters, 3mm (N2; more common) and 2.5mm (N1). Influence of MPS22 on diagnostic parameters: fractional flow reserve (FFR) and pressure drop coefficient (CDP) was evaluated both at hyperemic and basal conditions, while comparing it with G14. The FFR values decreased for the MPS22 in comparison to G14, (Mild: 0.87 vs 0.88, Intermediate: 0.68 vs 0.73, Severe: 0.48 vs 0.56) and CDP values increased (Mild: 16 vs 14, Intermediate: 75 vs 56, Severe: 370 vs 182) for N2. Similar trend was observed in the case of N1. The FFR values were found to be well above (mild) and below (intermediate and severe) the diagnostic cut-off of 0.75. Therefore, MPS22 catheter can be used as a possible alternative to G14. Further, irrespective of the MPS22 or G14, basal FFR (FFRb) had overlapping ranges in close proximity for clinically relevant mild and intermediate stenoses that will lead to diagnostic uncertainty under both N1 and N2. However, CDPb had distinct ranges for different stenosis severities and could be a potential diagnostic parameter under basal conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Method for extracting relevant electrical parameters from graphene field-effect transistors using a physical model

International Nuclear Information System (INIS)

Boscá, A.; Pedrós, J.; Martínez, J.; Calle, F.

2015-01-01

Due to its intrinsic high mobility, graphene has proved to be a suitable material for high-speed electronics, where graphene field-effect transistor (GFET) has shown excellent properties. In this work, we present a method for extracting relevant electrical parameters from GFET devices using a simple electrical characterization and a model fitting. With experimental data from the device output characteristics, the method allows to calculate parameters such as the mobility, the contact resistance, and the fixed charge. Differentiated electron and hole mobilities and direct connection with intrinsic material properties are some of the key aspects of this method. Moreover, the method output values can be correlated with several issues during key fabrication steps such as the graphene growth and transfer, the lithographic steps, or the metalization processes, providing a flexible tool for quality control in GFET fabrication, as well as a valuable feedback for improving the material-growth process

Method for extracting relevant electrical parameters from graphene field-effect transistors using a physical model

Energy Technology Data Exchange (ETDEWEB)

Boscá, A., E-mail: alberto.bosca@upm.es [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Dpto. de Ingeniería Electrónica, E.T.S.I. de Telecomunicación, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Pedrós, J. [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Campus de Excelencia Internacional, Campus Moncloa UCM-UPM, Madrid 28040 (Spain); Martínez, J. [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Dpto. de Ciencia de Materiales, E.T.S.I de Caminos, Canales y Puertos, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Calle, F. [Instituto de Sistemas Optoelectrónicos y Microtecnología, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Dpto. de Ingeniería Electrónica, E.T.S.I. de Telecomunicación, Universidad Politécnica de Madrid, Madrid 28040 (Spain); Campus de Excelencia Internacional, Campus Moncloa UCM-UPM, Madrid 28040 (Spain)

2015-01-28

Due to its intrinsic high mobility, graphene has proved to be a suitable material for high-speed electronics, where graphene field-effect transistor (GFET) has shown excellent properties. In this work, we present a method for extracting relevant electrical parameters from GFET devices using a simple electrical characterization and a model fitting. With experimental data from the device output characteristics, the method allows to calculate parameters such as the mobility, the contact resistance, and the fixed charge. Differentiated electron and hole mobilities and direct connection with intrinsic material properties are some of the key aspects of this method. Moreover, the method output values can be correlated with several issues during key fabrication steps such as the graphene growth and transfer, the lithographic steps, or the metalization processes, providing a flexible tool for quality control in GFET fabrication, as well as a valuable feedback for improving the material-growth process.

Influence of experimental parameters on the microencapsulation of a photopolymerizable phase.

Science.gov (United States)

Pernot, J M; Brun, H; Pouyet, B; Sergent, M; Phan-Tan-Luu, R

1993-01-01

Conditions of microencapsulation by in situ polycondensation, using melamine-formaldehyde as wall material, are influenced by the chemical nature of the core to encapsulate. In our study concerning the encapsulation of a photopolymerizable phase containing an electrically charged compound, it was necessary to modify the experimental process to obtain capsules of good quality. We used the factorial design method of screening by utilization of an asymmetric matrix, according to the collapsing principle of Addleman. The advantage of this method is that it allows determination of the simultaneous influences of the 11 experimental parameters involved in this preparation. The calculation method can be applied to more than two levels for some of the factors. The continuously varying parameters were altered between two extreme levels, chosen to allow encapsulation. For discontinuous factors, such as the molecular weight of the modifying system or nature of the aminoplast, we used the commercially available compounds, respectively three and four kinds. The results of the obtained capsules were determined by comparing microphotographic pictures. With 16 experiments we found four more factors influencing quality of capsules. We also determined the most favourable levels for the other seven parameters. The results allowed us to find optimal conditions in the experimental field. We obtained capsules of a satisfactory quality for this purpose, using only minimum experimentation.

Influence of choice of null network on small-world parameters of structural correlation networks.

Directory of Open Access Journals (Sweden)

S M Hadi Hosseini

Full Text Available In recent years, coordinated variations in brain morphology (e.g., volume, thickness have been employed as a measure of structural association between brain regions to infer large-scale structural correlation networks. Recent evidence suggests that brain networks constructed in this manner are inherently more clustered than random networks of the same size and degree. Thus, null networks constructed by randomizing topology are not a good choice for benchmarking small-world parameters of these networks. In the present report, we investigated the influence of choice of null networks on small-world parameters of gray matter correlation networks in healthy individuals and survivors of acute lymphoblastic leukemia. Three types of null networks were studied: 1 networks constructed by topology randomization (TOP, 2 networks matched to the distributional properties of the observed covariance matrix (HQS, and 3 networks generated from correlation of randomized input data (COR. The results revealed that the choice of null network not only influences the estimated small-world parameters, it also influences the results of between-group differences in small-world parameters. In addition, at higher network densities, the choice of null network influences the direction of group differences in network measures. Our data suggest that the choice of null network is quite crucial for interpretation of group differences in small-world parameters of structural correlation networks. We argue that none of the available null models is perfect for estimation of small-world parameters for correlation networks and the relative strengths and weaknesses of the selected model should be carefully considered with respect to obtained network measures.

Influence of Choice of Null Network on Small-World Parameters of Structural Correlation Networks

Science.gov (United States)

Hosseini, S. M. Hadi; Kesler, Shelli R.

2013-01-01

In recent years, coordinated variations in brain morphology (e.g., volume, thickness) have been employed as a measure of structural association between brain regions to infer large-scale structural correlation networks. Recent evidence suggests that brain networks constructed in this manner are inherently more clustered than random networks of the same size and degree. Thus, null networks constructed by randomizing topology are not a good choice for benchmarking small-world parameters of these networks. In the present report, we investigated the influence of choice of null networks on small-world parameters of gray matter correlation networks in healthy individuals and survivors of acute lymphoblastic leukemia. Three types of null networks were studied: 1) networks constructed by topology randomization (TOP), 2) networks matched to the distributional properties of the observed covariance matrix (HQS), and 3) networks generated from correlation of randomized input data (COR). The results revealed that the choice of null network not only influences the estimated small-world parameters, it also influences the results of between-group differences in small-world parameters. In addition, at higher network densities, the choice of null network influences the direction of group differences in network measures. Our data suggest that the choice of null network is quite crucial for interpretation of group differences in small-world parameters of structural correlation networks. We argue that none of the available null models is perfect for estimation of small-world parameters for correlation networks and the relative strengths and weaknesses of the selected model should be carefully considered with respect to obtained network measures. PMID:23840672

Parameters for calculation of nuclear reactions of relevance to non-energy nuclear applications (Reference Input Parameter Library: Phase III). Summary report of the first research coordination meeting

International Nuclear Information System (INIS)

Capote Noy, R.

2004-08-01

A summary is given of the First Research Coordination Meeting on Parameters for Calculation of Nuclear Reactions of Relevance to Non-Energy Nuclear Applications (Reference Input Parameter Library: Phase III), including a critical review of the RIPL-2 file. The new library should serve as input for theoretical calculations of nuclear reaction data at incident energies up to 200 MeV, as needed for energy and non-energy modern applications of nuclear data. Technical discussions and the resulting work plan of the Coordinated Research Programme are summarized, along with actions and deadlines. Participants' contributions to the RCM are also attached. (author)

Influence of fluiddynamic parameters upon fluid-hammer forces and spectra

International Nuclear Information System (INIS)

Meder, G.; Grams, J.

1984-01-01

For proper dynamic calculation of piping systems under fluid-hammer loading it is necessary to know the frequency content of the fluid-hammer force. Therefore, in this paper, the spectra of fluid-hammer loading will be examined. In particular, the influence of a change of fluiddynamic parameters upon the spectra will be investigated. When changes are made, the normal result is a change or shift in the frequency content of the spectra. However, for changes in certain fluiddynamic parameters, only the force amplitudes are changed. Both types of changes will be discussed. (orig.)

Influences of image resolution on herbaceous root morphological parameters

Directory of Open Access Journals (Sweden)

ZHANG Zeyou

2014-06-01

Full Text Available Root images of four herbaceous species (including Plantago virginica,Solidago canadensis,Conyza canadensis and Erigeron philadelphicus were obtained by using EPSON V7000 scanner with different resolutions.Root morphological parameters including root length,diameter,volume and area were determined by using a WinRhizo root analyzing software.The results show a distinct influence of image resolution on root morphological parameter.For different herbaceous species,the optimal resolutions of root images,which would produce an acceptable precision with relative short time,vary with different species.For example,a resolution of 200 dpi was recommended for the root images of Plantago virginica and S.Canadensis, while 400 dpi for Conyza canadensis and Erigeron philadelphicus.

Image quality - physical and diagnostic parameters. The radiologist's viewpoint

International Nuclear Information System (INIS)

Stender, H.St.

1985-01-01

The quality of a radiograph is determined by the diagnostic information it provides. This depends upon the visual detection of diagnostically relevant structures. The technical radiographic requirements are dependent upon the physical measurements and the physiological and optical conditions. Such physical factors as spatial resolution, contrast and noise are quantitative measurements, which must be oriented to the qualitative visual characteristics of the radiograph. The influence of subjective perception and complexity of structural noise on the detectability of details and structures particularly demands attention. Since radiographic quality depends upon the detection of diagnostically relevant structure and features, it is important to define these parameters on the basis of extensive radiographic analysis and the corresponding clinical findings. The diagnostically relevant radiographic parameters and image details and critical structures have been worked out for the examination of the lungs, colon, stomach, urinary tract and skeleton. Good image quality requires coordination of the physical-technical parameters with the visual ability of the observer, since only in this way can the diagnostic information be represented with sufficient clarity. (author)

Electrocardiographic parameters of the American Miniature Horse: influence of age and sex

Directory of Open Access Journals (Sweden)

Bianca P. Santarosa

2016-06-01

Full Text Available Abstract: The veterinary cardiology has growing importance in equine medicine. There are studies of standardization of electrocardiographic parameters of many races, according to their stature and ability. However, no studies are in the literature with the American Miniature Horse. To evaluate the electrocardiogram (ECG tracing configuration of this breed at rest and to verify the influence of age and sex on ECG parameters, 203 horses including 143 females and 60 males were divided into four age groups (foals, yearlings, adults and elderly. Electrocardiographic parameters were performed by computerized electrocardiogram (TEB, and the parameters were evaluated in six leads of frontal plane (Lead I, II, III, aVR, aVL and aVF and base-apex (BA. Heart rates (HR decreased with increasing age were higher in males than in females. Sinus tachycardia followed by sinus arrhythmia was dominant in both sexes. The cardiac axis was higher in males and ranged between 120° and 150° for foals, 30° and 60° for yearlings and adults, and 60° and 90° for the elderly. The P wave was bifid in several animals. The P-wave amplitude and T-wave duration from lead II and BA were larger in males than in females. The majority of the animals exhibited ST segment depression and a negative T-wave. The most common QRS complex morphology was Qr. Differences were observed between the electrocardiographic tracings of males and females, and age influenced the ECG parameters. Therefore, this study established the ECG patterns for the American Miniature Horse breed and could be used to determine the influence of age and sex on several of the studied variables.

Influence of Process Parameters on Nitrogen Oxide Formation in

DEFF Research Database (Denmark)

Lans, Robert Pieter Van Der; Glarborg, Peter; Dam-Johansen, Kim

1997-01-01

This paper describes the influence of burner operating conditions, burner geometry and fuel parameters on the formation of nitrogen oxide during combustion of pulverized coal. Main attention has been paid to combustion test facilities with self-sustaining flames, while extensions have been made...... to full scale boilers and furnace modeling. Since coal combustion and flame aerodynamics have been reviewed earlier, these phenomena are only treated briefly....

The parameters of X-ray equipment that influence in patient exposure

International Nuclear Information System (INIS)

Peixoto, J.E.

1988-01-01

The main components of the X-rays equipment and the secondary device for radiodiagnosis examination are showed. The influence of all radiographs parameters in human exposure as tension and current are also analysed. (C.G.C.) [pt

Influence of process parameters and biomass characteristics on the durability of pellets from the pruning residues of Olea europaea L.

Energy Technology Data Exchange (ETDEWEB)

Carone, Maria Teresa; Pantaleo, Antonio; Pellerano, Achille [Department of Engineering and Management of the Agricultural, Livestock and Forest Systems, Faculty of Agriculture, University of Bari, Via Amendola, 165/A, 70126 Bari (Italy)

2011-01-15

The present work aims to investigate the influence of the main process parameters (pressure and temperature) and biomass characteristics (moisture content and particle size) on some mechanical properties (density and durability) of olive tree pruning residues pellets. By means of a lab scale pellet press, able to control process parameters, the biomass, ground with three different hammer mill screen sizes (1, 2 and 4 mm) and conditioned at different moisture contents (5, 10, 15 and 20% w.b.), was pelletized at various process temperatures (60, 90, 120 and 150 C) and pressures (71, 106, 141 and 176 MPa). Compressed sample dimensions and mass were measured in order to calculate pellet density, while compressive strength tests were carried out to estimate the durability of the final biofuel. The relationships between the factor settings and the responses (density, compression strength and modulus of elasticity) were examined by univariate and multivariate statistical analysis. Temperature resulted the most important variable influencing pellet mechanical properties, followed by the initial moisture content and the particle size of the raw material. In particular, high process temperature, low moisture contents and reduced particle sizes allowed obtaining good quality pellets. The effect of compression force resulted scarcely relevant. (author)

Influence of core model parameters on the characteristics of neutron beams of the research reactor

Directory of Open Access Journals (Sweden)

N. A. Khafizova

2013-12-01

Full Text Available IRT MEPhI reactor is equipped with a number of facilities at horizontal experimental channels (HEC. Knowing of parameters influencing spatio-angular distribution of irradiation fields is essential for each application area. The research for neutron capture therapy (NCT facility at HEC of the reactor was made. Calculation methods have been used to estimate how the reactor core parameters influence neutron beam characteristics at the HEC output. The impact of neutron source model in Monte Carlo calculations by MCNP code on the parameters of neutron and secondary photon field at the output of irradiation beam tubes of research reactor is estimated. The study shows that specifying neutron source with fission reaction rate distribution in SDEF option gives almost the same results as criticality calculation considered the most accurate. Our calculations show that changes of the core operational parameters have insignificant influence on characteristics of neutron beams at HEC output.

Mood-congruent memory in depression - the influence of personal relevance and emotional context.

Science.gov (United States)

Wittekind, Charlotte E; Terfehr, Kirsten; Otte, Christian; Jelinek, Lena; Hinkelmann, Kim; Moritz, Steffen

2014-03-30

The investigation of veridical mood-congruent memory (MCM) in major depressive disorder (MDD) has been subject of many studies, whereas mood-congruent false memory has received comparatively little attention. The present study examined the influence of valence, personal relevance and the valence of the context of the learning material on true and false MCM in 20 inpatients with MDD and 20 healthy controls. Sixty positive, negative, neutral or personally relevant nouns were either combined with a positive, negative or neutral adjective. Word pairs were presented to participants in a learning trial. In a recognition task, participants had to identify the previously studied word pairs. A MCM effect could not be found for hits. However, in exploratory analyses, word pairs containing personally relevant nouns were more rated towards old by the patient relative to the control group. Furthermore, depressed patients tended to rate items more towards old than controls when the words were presented in a negative new context. Results are in line with previous findings in depression research emphasizing the role of mood-congruent false memories for mood disorders. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

Influence of various room parameters upon radon daughter equilibrium indoors

International Nuclear Information System (INIS)

Islam, G.S.; Mazumdar, S.C.; Ashraf, M.A.

1995-06-01

The parameters such as ventilation rate, attachment rate to aerosols and deposition processes, which influence the radon daughter equilibrium indoors, are discussed and the validity of the theoretical model checked by experiments. In agreement with the model calculations, the experimental data show, that the equilibrium factor F in rooms is mainly influenced by the rate of attachment to aerosols and the plateout of radon daughters. The equilibrium factor varies between 0.3 and 0.4 at an attachment rate of 300 h -1 . The influence of ventilation upon the free fraction of RaA( 218 Pp)-atoms is also investigated. This is in good agreement with the results of the measurements carried out in different types of rooms at the University Campus of Rajshahi. (author). 20 refs, 3 figs, 3 tabs

Inverse analyses of effective diffusion parameters relevant for a two-phase moisture model of cementitious materials

DEFF Research Database (Denmark)

Addassi, Mouadh; Johannesson, Björn; Wadsö, Lars

2018-01-01

Here we present an inverse analyses approach to determining the two-phase moisture transport properties relevant to concrete durability modeling. The purposed moisture transport model was based on a continuum approach with two truly separate equations for the liquid and gas phase being connected...... test, and, (iv) capillary suction test. Mass change over time, as obtained from the drying test, the two different cup test intervals and the capillary suction test, was used to obtain the effective diffusion parameters using the proposed inverse analyses approach. The moisture properties obtained...

Preaching to the choir? The influence of personal relevance on the effects of gain- and loss-framed health-promoting messages

NARCIS (Netherlands)

Riet, van 't J.P.; Ruiter, de R.; Vries, de H.

2012-01-01

This article examines the moderating influence of personal relevance on the persuasive effects of gain- and loss-framed messages. We assessed current behaviour as a proxy for personal relevance, provided 169 participants with gain- and loss-framed messages advocating skin self-examination (SSE) and

How attention influences perceptual decision making: Single-trial EEG correlates of drift-diffusion model parameters

Science.gov (United States)

Nunez, Michael D.; Vandekerckhove, Joachim; Srinivasan, Ramesh

2016-01-01

Perceptual decision making can be accounted for by drift-diffusion models, a class of decision-making models that assume a stochastic accumulation of evidence on each trial. Fitting response time and accuracy to a drift-diffusion model produces evidence accumulation rate and non-decision time parameter estimates that reflect cognitive processes. Our goal is to elucidate the effect of attention on visual decision making. In this study, we show that measures of attention obtained from simultaneous EEG recordings can explain per-trial evidence accumulation rates and perceptual preprocessing times during a visual decision making task. Models assuming linear relationships between diffusion model parameters and EEG measures as external inputs were fit in a single step in a hierarchical Bayesian framework. The EEG measures were features of the evoked potential (EP) to the onset of a masking noise and the onset of a task-relevant signal stimulus. Single-trial evoked EEG responses, P200s to the onsets of visual noise and N200s to the onsets of visual signal, explain single-trial evidence accumulation and preprocessing times. Within-trial evidence accumulation variance was not found to be influenced by attention to the signal or noise. Single-trial measures of attention lead to better out-of-sample predictions of accuracy and correct reaction time distributions for individual subjects. PMID:28435173

How attention influences perceptual decision making: Single-trial EEG correlates of drift-diffusion model parameters.

Science.gov (United States)

Nunez, Michael D; Vandekerckhove, Joachim; Srinivasan, Ramesh

2017-02-01

Perceptual decision making can be accounted for by drift-diffusion models, a class of decision-making models that assume a stochastic accumulation of evidence on each trial. Fitting response time and accuracy to a drift-diffusion model produces evidence accumulation rate and non-decision time parameter estimates that reflect cognitive processes. Our goal is to elucidate the effect of attention on visual decision making. In this study, we show that measures of attention obtained from simultaneous EEG recordings can explain per-trial evidence accumulation rates and perceptual preprocessing times during a visual decision making task. Models assuming linear relationships between diffusion model parameters and EEG measures as external inputs were fit in a single step in a hierarchical Bayesian framework. The EEG measures were features of the evoked potential (EP) to the onset of a masking noise and the onset of a task-relevant signal stimulus. Single-trial evoked EEG responses, P200s to the onsets of visual noise and N200s to the onsets of visual signal, explain single-trial evidence accumulation and preprocessing times. Within-trial evidence accumulation variance was not found to be influenced by attention to the signal or noise. Single-trial measures of attention lead to better out-of-sample predictions of accuracy and correct reaction time distributions for individual subjects.

On ballistic parameters of less lethal projectiles influencing the severity of thoracic blunt impacts.

Science.gov (United States)

Pavier, Julien; Langlet, André; Eches, Nicolas; Jacquet, Jean-François

2015-01-01

The development and safety certification of less lethal projectiles require an understanding of the influence of projectile parameters on projectile-chest interaction and on the resulting terminal effect. Several energy-based criteria have been developed for chest injury assessment. Many studies consider kinetic energy (KE) or energy density as the only projectile parameter influencing terminal effect. In a common KE range (100-160 J), analysis of the firing tests of two 40 mm projectiles of different masses on animal surrogates has been made in order to investigate the severity of the injuries in the thoracic region. Experimental results have shown that KE and calibre are not sufficient to discriminate between the two projectiles as regards their injury potential. Parameters, such as momentum, shape and impedance, influence the projectile-chest interaction and terminal effect. A simplified finite element model of projectile-structure interaction confirms the experimental tendencies. Within the range of ballistic parameters used, it has been demonstrated that maximum thoracic deflection is a useful parameter to predict the skeletal level of injury, and it largely depends on the projectile pre-impact momentum. However, numerical simulations show that these results are merely valid for the experimental conditions used and cannot be generalised. Nevertheless, the transmitted impulse seems to be a more general factor governing the thorax deflection.

Influence of parameters detuning on induction motor NFO shaft-sensorless scheme

Directory of Open Access Journals (Sweden)

KULIC, F.

2010-11-01

Full Text Available In this paper, the parameter sensitivity analysis of shaft-sensorless induction motor drive with natural field orientation (NFO scheme is performed. NFO scheme calculates rotor flux position using the rotor flux vector reference only, does not require significant processor power and therefore it is suitable for low cost shaft sensorless drives. This concept also eliminates the need for sensitive stator voltage vector integration and it is usable in low rotor speed range. However, low speeds are coupled with low stator voltage amplitudes, which inflate the NFO scheme sensitivity to an error in stator resistance parameter. Similar problems can also take place if mutual inductance parameter is detuned, but this time in whole speed range. This paper investigates the influence of each parameter error on the NFO control steady state characteristics and dynamic performance.

Influence of short-term sampling parameters on the uncertainty of the Lden environmental noise indicator

International Nuclear Information System (INIS)

Mateus, M; Carrilho, J Dias; Da Silva, M Gameiro

2015-01-01

The present study deals with the influence of the sampling parameters on the uncertainty of noise equivalent level in environmental noise measurements. The study has been carried out through the test of different sampling strategies doing resampling trials over continuous monitoring noise files obtained previously in an urban location in the city of Coimbra, in Portugal. On short term measurements, not only the duration of the sampling episodes but also its number have influence on the uncertainty of the result. This influence is higher for the time periods where sound levels suffer a greater variation, such as during the night period. In this period, in case both parameters (duration and number of sampling episodes) are not carefully selected, the uncertainty level can reach too high values contributing to a loss of precision of the measurements. With the obtained data it was investigated the sampling parameters influence on the long term noise indicator uncertainty, calculated according the Draft 1st CD ISO 1996-2:2012 proposed method. It has been verified that this method allows the possibility of defining a general methodology which enables the setting of the parameters once the precision level is fixed. For the three reference periods defined for environmental noise (day, evening and night), it was possible to derive a two variable power law representing the uncertainty of the determined values as a function of the two sampling parameters: duration of sampling episode and number of episodes

Coupled 1D-2D hydrodynamic inundation model for sewer overflow: Influence of modeling parameters

Directory of Open Access Journals (Sweden)

Adeniyi Ganiyu Adeogun

2015-10-01

Full Text Available This paper presents outcome of our investigation on the influence of modeling parameters on 1D-2D hydrodynamic inundation model for sewer overflow, developed through coupling of an existing 1D sewer network model (SWMM and 2D inundation model (BREZO. The 1D-2D hydrodynamic model was developed for the purpose of examining flood incidence due to surcharged water on overland surface. The investigation was carried out by performing sensitivity analysis on the developed model. For the sensitivity analysis, modeling parameters, such as mesh resolution Digital Elevation Model (DEM resolution and roughness were considered. The outcome of the study shows the model is sensitive to changes in these parameters. The performance of the model is significantly influenced, by the Manning's friction value, the DEM resolution and the area of the triangular mesh. Also, changes in the aforementioned modeling parameters influence the Flood characteristics, such as the inundation extent, the flow depth and the velocity across the model domain. Keywords: Inundation, DEM, Sensitivity analysis, Model coupling, Flooding

The Influence of Social Parameters on the Homing Behavior of Pigeons.

Directory of Open Access Journals (Sweden)

Julia Mehlhorn

Full Text Available Homing pigeons develop preferred routes when released alone several times from the same site, but they sometimes diverge from their preferred route when subsequently released with another pigeon. Additionally, group flights show a better homing performance than solo flights. But this knowledge is based on studies involving both sexes and lacks analyses of social parameters such as mating or breeding status, even though it is known that such parameters have an influence on behavior and on motivation for specific behavioral patterns. GPS trackers were used to track 24 homing pigeons (9 breeding pairs and 6 unmated females as they performed a familiar 10km route in various pair and group combinations. Comparisons of efficiency indices (quotient between straight-line distance and pigeon's track reveal that unmated females show the best efficiency in single flights. Generally, group flights show the best efficiency followed by pair flights with a social partner of the opposite sex. Pair flights with the mated partner exhibit the poorest performance. Additionally, just before squabs hatching, females show a higher efficiency index when released at 8 am, compared to releases at 2 pm. Our results indicate that homing flight efficiency can provide insight into individual motivation and that social parameters have an influence on homing performance on a familiar route.

INFLUENCE OF TECHNOLOGICAL PARAMETERS ON AGROTEXTILES WATER ABSORBENCY USING ANOVA MODEL

Directory of Open Access Journals (Sweden)

LUPU Iuliana G.

2016-05-01

Full Text Available Agrotextiles are now days extensively being used in horticulture, farming and other agricultural activities. Agriculture and textiles are the largest industries in the world providing basic needs such as food and clothing. Agrotextiles plays a significant role to help control environment for crop protection, eliminate variations in climate, weather change and generate optimum condition for plant growth. Water absorptive capacity is a very important property of needle-punched nonwovens used as irrigation substrate in horticulture. Nonwovens used as watering substrate distribute water uniformly and act as slight water buffer owing to the absorbent capacity. The paper analyzes the influence of needling process parameters on water absorptive capacity of needle-punched nonwovens by using ANOVA model. The model allows the identification of optimal action parameters in a shorter time and with less material expenses than by experimental research. The frequency of needle board and needle depth penetration has been used as independent variables while the water absorptive capacity as dependent variable for ANOVA regression model. Based on employed ANOVA model we have established that there is a significant influence of needling parameters on water absorbent capacity. The higher of depth needle penetration and needle board frequency, the higher is the compactness of fabric. A less porous structure has a lower water absorptive capacity.

Soil physical properties influencing the fitting parameters in Philip and Kostiakov infiltration models

International Nuclear Information System (INIS)

Mbagwu, J.S.C.

1994-05-01

Among the many models developed for monitoring the infiltration process those of Philip and Kostiakov have been studied in detail because of their simplicity and the ease of estimating their fitting parameters. The important soil physical factors influencing the fitting parameters in these infiltration models are reported in this study. The results of the study show that the single most important soil property affecting the fitting parameters in these models is the effective porosity. 36 refs, 2 figs, 5 tabs

Surgeon Reported Outcome Measure for Spine Trauma an International Expert Survey Identifying Parameters Relevant for The Outcome of Subaxial Cervical Spine Injuries

NARCIS (Netherlands)

Sadiqi, Said; Verlaan, Jorrit Jan; Lehr, A. M.; Dvorak, Marcel F.; Kandziora, Frank; Rajasekaran, S.; Schnake, Klaus J.; Vaccaro, Alexander R.; Oner, F. C.

2016-01-01

STUDY DESIGN.: International web-based survey OBJECTIVE.: To identify clinical and radiological parameters that spine surgeons consider most relevant when evaluating clinical and functional outcomes of subaxial cervical spine trauma patients. SUMMARY OF BACKGROUND DATA.: While an outcome instrument

Influence of xenobiotics on the microbiological and agrochemical parameters of soddy-podzolic soil

Science.gov (United States)

Vakkerov-Kouzova, N. D.

2010-08-01

We studied the influence of various chemical compounds, i.e., azobenzene (an insecticide and acaricide), nitrification inhibitors (DCD, dicyandiamide and DMPP, and 3,4-dimetylpyrazolphosphate), and inhibitors of urease activity (HQ-hydroquinone), on the agrochemical and microbiological parameters of a soddy-podzolic soil. It is proved that these xenobiotics are able to influence the agrochemical parameters (the pH and the content of NO{3/-} and NH{4/+}, the microbial activity (the basal respiration, the microbial mass carbon, and the microbial quotient), and the number of bacteria of different physiological groups in soddypodzolic soil. The influence of the xenobiotics was preserved for some time, which testified to their persistence in the soil. Upon cultivating the soil microorganisms in different media, the growth of the heterotrophic bacteria was inhibited, the radial growth velocity was slowed down, and the sporogenesis of the micromycetes was retarded. The toxic effect of the xenobiotics was higher with their increasing concentrations.

Influence of buildings geometrical and physical parameters on thermal cooling load

International Nuclear Information System (INIS)

Melo, C.

1980-09-01

A more accurate method to evaluate the thermal cooling load in buildings and to analyze the influence of geometrical and physical parameters on air conditioning calculations is presented. The sensitivity of the cooling load, considering the thermal capacity of the materials, was simulated in a computer for several different situations. (Author) [pt

Characterizing rainfall parameters which influence erosivity in southeastern Nigeria

International Nuclear Information System (INIS)

Obi, M.E.; Salako, F.K.

1993-12-01

An investigation was carried out to characterize some selected parameters which influence rainfall erosivity in southeastern Nigeria. Rainfall amount, distribution, duration, intensity, storm types, energy loads and frequency of rain events in the region were studied using data from stations located in three major agroecological zones. Raindrop size and detaching capacity were evaluated in one of the stations for two months. The mean annual rainfall erosivity values for southeastern Nigeria point to the fact that rainfall tend to be highly erosive. 25 refs, 6 figs, 8 tabs

Modifying factors for metabolic parameters

International Nuclear Information System (INIS)

Inaba, Jiro

1990-01-01

Studies on factors which influence the metabolic parameter for calculation of radiation doses from intakes of radionuclides are very important for estimation of the doses for the general public, because the present procedures recommended by the International Commission on Radiological Protection is for occupationally exposed workers and the underlying metabolic and dosimetric models have been developed from studies on adult man and experiments on adult animals and from observations on radionuclides in physico-chemically simple form. Many factors have been reported to influence the metabolic parameters. Among them, the food-chain involvement of radionuclides and the age-dependence in humans and animals are most significant as environmental and physiological factor, respectively. In connection with the age-dependence of dose calculation, the ICRP started a new programme. They organized a Task Group on Age-Dependent Dose-Factors where relevant information on metabolic and biokinetic parameters are presently being reviewed for development of a set of dose factors for the following age-groups: infant, 1-year-old, 5-year-old, 10-year-old, 15-year-old, and ICRP Reference Man. The first stage of the work is for age-dependent integrated organ and effective dose factors for radioisotopes of the following elements: hydrogen, carbon, iodine, cesium, strontium, plutonium and americium. (author)

Influence of Population Variation of Physiological Parameters in Computational Models of Space Physiology

Science.gov (United States)

Myers, J. G.; Feola, A.; Werner, C.; Nelson, E. S.; Raykin, J.; Samuels, B.; Ethier, C. R.

2016-01-01

The earliest manifestations of Visual Impairment and Intracranial Pressure (VIIP) syndrome become evident after months of spaceflight and include a variety of ophthalmic changes, including posterior globe flattening and distension of the optic nerve sheath. Prevailing evidence links the occurrence of VIIP to the cephalic fluid shift induced by microgravity and the subsequent pressure changes around the optic nerve and eye. Deducing the etiology of VIIP is challenging due to the wide range of physiological parameters that may be influenced by spaceflight and are required to address a realistic spectrum of physiological responses. Here, we report on the application of an efficient approach to interrogating physiological parameter space through computational modeling. Specifically, we assess the influence of uncertainty in input parameters for two models of VIIP syndrome: a lumped-parameter model (LPM) of the cardiovascular and central nervous systems, and a finite-element model (FEM) of the posterior eye, optic nerve head (ONH) and optic nerve sheath. Methods: To investigate the parameter space in each model, we employed Latin hypercube sampling partial rank correlation coefficient (LHSPRCC) strategies. LHS techniques outperform Monte Carlo approaches by enforcing efficient sampling across the entire range of all parameters. The PRCC method estimates the sensitivity of model outputs to these parameters while adjusting for the linear effects of all other inputs. The LPM analysis addressed uncertainties in 42 physiological parameters, such as initial compartmental volume and nominal compartment percentage of total cardiac output in the supine state, while the FEM evaluated the effects on biomechanical strain from uncertainties in 23 material and pressure parameters for the ocular anatomy. Results and Conclusion: The LPM analysis identified several key factors including high sensitivity to the initial fluid distribution. The FEM study found that intraocular pressure and

Influence of Drilling Parameters on Torque during Drilling of GFRP Composites Using Response Surface Methodology

Science.gov (United States)

Mohan, N. S.; Kulkarni, S. M.

2018-01-01

Polymer based composites have marked their valuable presence in the area of aerospace, defense and automotive industry. Components made of composite, are assembled to main structure by fastener, which require accurate, precise high quality holes to be drilled. Drilling the hole in composite with accuracy require control over various processes parameters viz., speed, feed, drill bit size and thickens of specimen. TRIAC VMC machining center is used to drill the hole and to relate the cutting and machining parameters on the torque. MINITAB 14 software is used to analyze the collected data. As a function of cutting and specimen parameters this method could be useful for predicting torque parameters. The purpose of this work is to investigate the effect of drilling parameters to get low torque value. Results show that thickness of specimen and drill bit size are significant parameters influencing the torque and spindle speed and feed rate have least influence and overlaid plot indicates a feasible and low region of torque is observed for medium to large sized drill bits for the range of spindle speed selected. Response surface contour plots indicate the sensitivity of the drill size and specimen thickness to the torque.

Integrating retention soil filters into urban hydrologic models - Relevant processes and important parameters

Science.gov (United States)

Bachmann-Machnik, Anna; Meyer, Daniel; Waldhoff, Axel; Fuchs, Stephan; Dittmer, Ulrich

2018-04-01

Retention Soil Filters (RSFs), a form of vertical flow constructed wetlands specifically designed for combined sewer overflow (CSO) treatment, have proven to be an effective tool to mitigate negative impacts of CSOs on receiving water bodies. Long-term hydrologic simulations are used to predict the emissions from urban drainage systems during planning of stormwater management measures. So far no universally accepted model for RSF simulation exists. When simulating hydraulics and water quality in RSFs, an appropriate level of detail must be chosen for reasonable balancing between model complexity and model handling, considering the model input's level of uncertainty. The most crucial parameters determining the resultant uncertainties of the integrated sewer system and filter bed model were identified by evaluating a virtual drainage system with a Retention Soil Filter for CSO treatment. To determine reasonable parameter ranges for RSF simulations, data of 207 events from six full-scale RSF plants in Germany were analyzed. Data evaluation shows that even though different plants with varying loading and operation modes were examined, a simple model is sufficient to assess relevant suspended solids (SS), chemical oxygen demand (COD) and NH4 emissions from RSFs. Two conceptual RSF models with different degrees of complexity were assessed. These models were developed based on evaluation of data from full scale RSF plants and column experiments. Incorporated model processes are ammonium adsorption in the filter layer and degradation during subsequent dry weather period, filtration of SS and particulate COD (XCOD) to a constant background concentration and removal of solute COD (SCOD) by a constant removal rate during filter passage as well as sedimentation of SS and XCOD in the filter overflow. XCOD, SS and ammonium loads as well as ammonium concentration peaks are discharged primarily via RSF overflow not passing through the filter bed. Uncertainties of the integrated

The influence of various dielectric parameters on the reststrahlen region of SiC

International Nuclear Information System (INIS)

Engelbrecht, J.A.A.; Rooyen, I.J. van

2011-01-01

The reststrahlen region of SiC is analysed with the goal of establishing the origin of different shapes of this band, by varying the dielectric parameters involved when simulating the reststrahlen region as obtained by infrared reflectance. -- Research highlights: → An anomalous peak observed in the reststrahlen band of SiC was investigated. → The reflection spectrum of SiC in the reststrahlen region was simulated by theoretical calculations. → The influence on the reststrahlen band of the dielectric parameters used in the simulations is discussed. → Dielectric parameters used in the simulations did not yield the anomalous peak that is observed experimentally.

The influence of various dielectric parameters on the reststrahlen region of SiC

Energy Technology Data Exchange (ETDEWEB)

Engelbrecht, J.A.A., E-mail: Japie.Engelbrecht@nmmu.ac.z [Physics Department, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa); Rooyen, I.J. van [Physics Department, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa); National Laser Centre, CSIR, PO Box 395, Pretoria 0001 (South Africa)

2011-02-01

The reststrahlen region of SiC is analysed with the goal of establishing the origin of different shapes of this band, by varying the dielectric parameters involved when simulating the reststrahlen region as obtained by infrared reflectance. -- Research highlights: {yields} An anomalous peak observed in the reststrahlen band of SiC was investigated. {yields} The reflection spectrum of SiC in the reststrahlen region was simulated by theoretical calculations. {yields} The influence on the reststrahlen band of the dielectric parameters used in the simulations is discussed. {yields} Dielectric parameters used in the simulations did not yield the anomalous peak that is observed experimentally.

Influence of meteorological parameters on interception of cloud droplets in a coniferous forest

Energy Technology Data Exchange (ETDEWEB)

Kroll, G; Winkler, P [Deutscher Wetterdienst, Meteorologisches Observatorium Hamburg (Germany, F.R.)

1989-11-01

The deposition of trace substances in a high elevated coniferous forest by interception of cloud droplets depends on numerous meteorological parameters. Sensitivity studies with a deposition model show that the variation of the vertical wind profile in the stand and the capture efficiency have a large influence on the deposition flux. Different drop size distributions with equal LWC's lead to changes of only 10% in the deposition flux. A higher ion concentration in small droplets has only a small influence on the trace substance deposition. A realistic estimate of the deposition is most likely achieved by using hourly observed meteorological parameters as model input values. The deposition of trace substances into a high elevated coniferous forest by interception of cloud droplets can be as high as the deposition via rain. (orig.).

Influences of geological parameters to probabilistic assessment of slope stability of embankment

Science.gov (United States)

Nguyen, Qui T.; Le, Tuan D.; Konečný, Petr

2018-04-01

This article considers influences of geological parameters to slope stability of the embankment in probabilistic analysis using SLOPE/W computational system. Stability of a simple slope is evaluated with and without pore–water pressure on the basis of variation of soil properties. Normal distributions of unit weight, cohesion and internal friction angle are assumed. Monte Carlo simulation technique is employed to perform analysis of critical slip surface. Sensitivity analysis is performed to observe the variation of the geological parameters and their effects on safety factors of the slope stability.

The influence of control parameter estimation on large scale geomorphological interpretation of pointclouds

Science.gov (United States)

Dorninger, P.; Koma, Z.; Székely, B.

2012-04-01

In recent years, laser scanning, also referred to as LiDAR, has proved to be an important tool for topographic data acquisition. Basically, laser scanning acquires a more or less homogeneously distributed point cloud. These points represent all natural objects like terrain and vegetation as well as man-made objects such as buildings, streets, powerlines, or other constructions. Due to the enormous amount of data provided by current scanning systems capturing up to several hundred thousands of points per second, the immediate application of such point clouds for large scale interpretation and analysis is often prohibitive due to restrictions of the hard- and software infrastructure. To overcome this, numerous methods for the determination of derived products do exist. Commonly, Digital Terrain Models (DTM) or Digital Surface Models (DSM) are derived to represent the topography using a regular grid as datastructure. The obvious advantages are a significant reduction of the amount of data and the introduction of an implicit neighborhood topology enabling the application of efficient post processing methods. The major disadvantages are the loss of 3D information (i.e. overhangs) as well as the loss of information due to the interpolation approach used. We introduced a segmentation approach enabling the determination of planar structures within a given point cloud. It was originally developed for the purpose of building modeling but has proven to be well suited for large scale geomorphological analysis as well. The result is an assignment of the original points to a set of planes. Each plane is represented by its plane parameters. Additionally, numerous quality and quantity parameters are determined (e.g. aspect, slope, local roughness, etc.). In this contribution, we investigate the influence of the control parameters required for the plane segmentation on the geomorphological interpretation of the derived product. The respective control parameters may be determined

Influence of electrospinning parameters on the structural morphology and diameter of electrospun nanofibers

CSIR Research Space (South Africa)

Jacobs, V

2009-11-01

Full Text Available Electrospinning is a simple method of producing nanofibers by introducing electric field into the polymer solutions. We report an experimental investigation on the influence of processing parameters and solution properties on the structural...

Science and the struggle for relevance

NARCIS (Netherlands)

Hessels, L.K.|info:eu-repo/dai/nl/304832863

2010-01-01

This thesis deals with struggles for relevance of university researchers, their efforts to make their work correspond with ruling standards of relevance and to influence these standards. Its general research question is: How to understand changes in the struggle for relevance of Dutch academic

Motorcycle On-Road Driving Parameters Influencing Fuel Consumption and Emissions on Congested Signalized Urban Corridor

Directory of Open Access Journals (Sweden)

Atthapol Seedam

2017-01-01

Full Text Available This study aims to find the on-road driving parameters influencing fuel consumption and emissions of motorcycle driving on a congested signalized urban corridor. A motorcycle onboard measurement system was developed to measure instantaneously and continuously record on-road driving data, including speed-time profile, emissions, and fuel consumption, by the second. The test motorcycles were driven by 30 sample motorcyclists on a signalized urban corridor in Khon Kaen City, Thailand, to collect their on-road driving behavior during the morning peak period. Cluster analysis was applied to analyze collected driving data and to categorize the drivers by level of fuel consumption and on-road driver behavior. The on-road driving parameter influencing fuel consumption and emissions was then determined. Results revealed that proportion of idle time significantly influenced fuel consumption and emissions of motorcycle driving on a congested signalized urban corridor, though aggressive driving behavior, hard acceleration and deceleration, did not have the same kind of influence.

Influence of some design and operating parameters of conveyor with suspended belt and distributed drive on the technical specifications

Directory of Open Access Journals (Sweden)

Tolkachev E.N.

2017-03-01

Full Text Available The influence of several design and operating parameters of conveyor on the individual components of the stretching tension in the belt of conveyor with suspended belt and distributed drive was analyzed. The analysis of influence a number design and operating parameters on the technical specifications of conveyor with suspended belt and distributed drive was done. Recommendations on the choice of rational parameters were formulated.

Influence of some design and operating parameters of conveyor with suspended belt and distributed drive on the technical specifications

OpenAIRE

Tolkachev E.N.

2017-01-01

The influence of several design and operating parameters of conveyor on the individual components of the stretching tension in the belt of conveyor with suspended belt and distributed drive was analyzed. The analysis of influence a number design and operating parameters on the technical specifications of conveyor with suspended belt and distributed drive was done. Recommendations on the choice of rational parameters were formulated.

Influence of additive laser manufacturing parameters on surface using density of partially melted particles

Science.gov (United States)

Rosa, Benoit; Brient, Antoine; Samper, Serge; Hascoët, Jean-Yves

2016-12-01

Mastering the additive laser manufacturing surface is a real challenge and would allow functional surfaces to be obtained without finishing. Direct Metal Deposition (DMD) surfaces are composed by directional and chaotic textures that are directly linked to the process principles. The aim of this work is to obtain surface topographies by mastering the operating process parameters. Based on experimental investigation, the influence of operating parameters on the surface finish has been modeled. Topography parameters and multi-scale analysis have been used in order to characterize the DMD obtained surfaces. This study also proposes a methodology to characterize DMD chaotic texture through topography filtering and 3D image treatment. In parallel, a new parameter is proposed: density of particles (D p). Finally, this study proposes a regression modeling between process parameters and density of particles parameter.

PARAMETERS WHICH INFLUENCE EMPLOYEE SATISFACTION IN PUBLIC SECTOR IN THE REPUBLIC OF CROATIA

Directory of Open Access Journals (Sweden)

Igor Klopotan

2018-06-01

Full Text Available Employees are one of key factors of success of a company and as such represent the most important resource of every organisation. In order to efficiently and effectively complete the tasks assigned to them, employees need to be motivated and satisfied with the work they do. Human resources management is a complex and demanding process and tasks administered by human resources manager are by no means simple. Parameters of employee satisfaction differ in public and private sector. Research indicates that direct financial rewards are not the most important parameter of employee satisfaction. Research conducted within this paper indicates that in the Republic of Croatia there are several relevant parameters of employee satisfaction and they are dependent on education, age, professional qualification level and length of service. Research results also indicate that informants are not of the opinion that salaries are based on work results. This research was a part of a bigger research conducted in public sector of the Republic of Croatia.

How far are transmission measurements of pre-equilibrium stopping influenced by impact parameter selection?

International Nuclear Information System (INIS)

Semrad, D.; Bergsmann, M.; Bauer, P.; Diez-Muino, R.; Arnau, S.A.

2000-01-01

A slow ion that impinges on a target will need to travel a certain distance within the target - called pre-equilibrium length - in order to reach charge equilibrium. In this transient region, projectiles may suffer energy loss different from the mean value. For gas targets, most of the relevant cross-sections and energy transfers can be determined separately by experiment. This allows one to relate these data to the stopping cross-section and to simulate the passage of ions through gas by Monte-Carlo techniques. For solid targets matter is worse, but a universal formalism how pre-equilibrium processes may be determined from transmission data is well documented by Sigmund [14-15]. In transmission experiments usually only these projectiles are analyzed that have missed the central region of the target atoms. It is, however, a matter of fact that projectiles passing closer to the nucleus are more likely to lose energy. In the case of thin targets these projectiles are deflected out of the detector acceptance leading to a reduction of the measured average energy loss. Hence, stopping data may be influenced by so-called impact parameter selection (IPS) according to the layout of the experiment. This IPS clearly acts also in the regime of pre-equilibrium stopping. Using Monte-Carlo simulation we studied to which extent in a typical transmission experiment energy loss is influenced by pre-equilibrium stopping and by IPS, respectively. For feasibility, instead of a solid target, we follow the trajectories through a dense gas target. We find that in an actual experiment with small detector opening angle the formalism to describe pre-equilibrium stopping has to include IPS

Influence of surface features of hydroxyapatite on the adsorption of proteins relevant to bone regeneration.

Science.gov (United States)

Fernández-Montes Moraleda, Belén; San Román, Julio; Rodríguez-Lorenzo, Luís M

2013-08-01

Protein-surface interaction may determine the success or failure of an implanted device. Not much attention have been paid to the specific surface parametes of hydroxyapatite (OHAp) that modulates and determines the formation and potential activity of the layer of proteins that is first formed when the material get in contact with the host tissue. the influence of specific surface area (SSA), crystallite size (CS) and particle size (PS) of OHAp on the adsorption of proteins relevant for bone regeneration is evaluated in this article. OHAp have been prepared by a wet chemical reaction of Ca(OH)2 with H3PO4. One set of reactions included poly acrylic acid in the reactant solution to modify the properties of the powder. Fibrinogen (Fg) Fraction I, type I: from Human plasma, (67% Protein), and Fibronectin (Fn) from Human plasma were selected to perform the adsorption experiments. The analysis of protein adsorption was carried out by UV/Vis spectrometry. A lower SSA and a different aspect ratio are obtained when the acrylic acid is included in the reaction badge. The deconvolution of the amide I band on the Raman spectra of free and adsorbed proteins reveals that the interaction apatite-protein happens through the carboxylate groups of the proteins. The combined analysis of CS, SSA and PS should be considered on the design of OHAp materials intended to interact with proteins. Copyright © 2013 Wiley Periodicals, Inc.

Ion-beam-induced aggregation in polystyrene: The influence of the molecular parameters

International Nuclear Information System (INIS)

Puglisi, O.; Licciardello, A.; Calcagno, L.; Foti, G.

1988-01-01

The formation of an insoluble gel under ion-beam bombardment is governed by ion-beam parameters and target parameters. Here reported is a study of the influence of the target molecular parameters on the sol--gel transition of ion-bombarded polystyrene with particular emphasis for the number-average molecular weight M-bar/sub n/. It is shown that the main parameter is the number of macromolcules of the film so that by adopting a ''corrected'' fluence F/n (ions per macromolecule), the different curves of the various polymers collapse in only one universal curve. The importance of the ''corrected'' fluence is shown also at molecular level and the MWD of the various polymers is similar at equal F/n values. An experimental model is outlined which explains the sol--gel transition on the basis of transition from an isolated-track regime to an overlap regime where the formation of insoluble giant macromolecules occurs

Determinants of dermal exposure relevant for exposure modelling in regulatory risk assessment.

Science.gov (United States)

Marquart, J; Brouwer, D H; Gijsbers, J H J; Links, I H M; Warren, N; van Hemmen, J J

2003-11-01

Risk assessment of chemicals requires assessment of the exposure levels of workers. In the absence of adequate specific measured data, models are often used to estimate exposure levels. For dermal exposure only a few models exist, which are not validated externally. In the scope of a large European research programme, an analysis of potential dermal exposure determinants was made based on the available studies and models and on the expert judgement of the authors of this publication. Only a few potential determinants appear to have been studied in depth. Several studies have included clusters of determinants into vaguely defined parameters, such as 'task' or 'cleaning and maintenance of clothing'. Other studies include several highly correlated parameters, such as 'amount of product handled', 'duration of task' and 'area treated', and separation of these parameters to study their individual influence is not possible. However, based on the available information, a number of determinants could clearly be defined as proven or highly plausible determinants of dermal exposure in one or more exposure situation. This information was combined with expert judgement on the scientific plausibility of the influence of parameters that have not been extensively studied and on the possibilities to gather relevant information during a risk assessment process. The result of this effort is a list of determinants relevant for dermal exposure models in the scope of regulatory risk assessment. The determinants have been divided into the major categories 'substance and product characteristics', 'task done by the worker', 'process technique and equipment', 'exposure control measures', 'worker characteristics and habits' and 'area and situation'. To account for the complex nature of the dermal exposure processes, a further subdivision was made into the three major processes 'direct contact', 'surface contact' and 'deposition'.

Influence of the growth parameters on TiO2 thin films deposited using the MOCVD method

Directory of Open Access Journals (Sweden)

Bernardi M. I. B.

2002-01-01

Full Text Available In this work we report the synthesis of TiO2 thin films by the Organometallic Chemical Vapor Deposition (MOCVD method. The influence of deposition parameters used during the growth in the obtained structural characteristics was studied. Different temperatures of the organometallic bath, deposition time, temperature and type of the substrate were combined. Using Scanning Electron Microscopy associated to Electron Dispersive X-Ray Spectroscopy, Atomic Force Microscopy and X-ray Diffraction, the strong influence of these parameters in the thin films final microstructure was verified.

In vitro dynamic solubility test: influence of various parameters.

Science.gov (United States)

Thélohan, S; de Meringo, A

1994-10-01

This article discusses the dissolution of mineral fibers in simulated physiological fluids (SPF), and the parameters that affect the solubility measurement in a dynamic test where an SPF runs through a cell containing fibers (Scholze and Conradt test). Solutions simulate either the extracellular fluid (pH 7.6) or the intracellular fluid (pH 4.5). The fibers have various chemical compositions and are either continuously drawn or processed as wool. The fiber solubility is determined by the amount of SiO2 (and occasionally other ions) released in the solution. Results are stated as percentage of the initial silica content released or as dissolution rate v in nm/day. The reproducibility of the test is higher with the less soluble fibers (10% solubility), than with highly soluble fibers (20% solubility). The influence of test parameters, including SPF, test duration, and surface area/volume (SA/V), has been studied. The pH and the inorganic buffer salts have a major influence: industrial glasswool composition is soluble at pH 7.6 but not at pH 4.5. The opposite is true for rock- (basalt) wool composition. For slightly soluble fibers, the dissolution rate v remains constant with time, whereas for highly soluble fibers, the dissolution rate decreases rapidly. The dissolution rates believed to occur are v1, initial dissolution rate, and v2, dissolution rate of the residual fibers. The SA of fibers varies with the mass of the fibers tested, or with the fiber diameter at equal mass. Volume, V, is the chosen flow rate. An increase in the SA/V ratio leads to a decrease in the dissolution rate.(ABSTRACT TRUNCATED AT 250 WORDS)

The influence of hyper-parameters in the infinite relational model

DEFF Research Database (Denmark)

Albers, Kristoffer Jon; Mørup, Morten; Schmidt, Mikkel Nørgaard

2016-01-01

the importance of these priors for discovering latent clusters and for predicting links. We compare fixed symmetric priors and fixed asymmetric priors based on the empirical distribution of links with a Bayesian hierarchical approach where the parameters of the priors are inferred from data. On synthetic data......, we show that the hierarchical Bayesian approach can infer the prior distributions used to generate the data. On real network data we demonstrate that using asymmetric priors significantly improves predictive performance and heavily influences the number of extracted partitions....

HEC influence on cement hydration measured by conductometry

OpenAIRE

Pourchez , Jérémie; Grosseau , Philippe; Guyonnet , René; Ruot , Bertrand

2006-01-01

International audience; Cellulose ethers are of universal use in factory-made mortars, though their influences on mortar properties at a molecular scale are poorly understood. Recent studies dealt with the influence of hydroxyethylmethyl cellulose (HEMC) and hydroxypropylmethyl cellulose (HPMC) molecular parameters on cement hydration. It was concluded that the degree of substitution is the most relevant factor on cement hydration kinetics, contrary to the molecular weight. Nevertheless, the ...

Influence of environmental parameters on the frictional behavior of DLC coatings

Energy Technology Data Exchange (ETDEWEB)

Liu, Y. [Louisiana State Univ., Baton Rouge, LA (United States). Mechanical Engineering Dept.; Erdemir, A.; Meletis, E.I. [Argonne National Lab., IL (United States). Energy Technology Div.

1997-05-01

In a previous studies it was shown that diamond like carbon (DLC) films possess low friction coefficient (f) and excellent wear resistance. The reduction in f was found to be consistent with a ``wear induced graphitization`` mechanism of the DLC structure. A recent study showed that operational parameters (sliding velocity and loading level) influence the tribological behavior of DLC film through control of the kinetics of the graphitization process. The objective of the present study was to investigate the influence of environmental parameters (humidity and temperature) on the tribological behavior of DLC film and provide further support to the wear induced graphitization mechanism. Ion beam deposition was utilized to deposit DLC on a SiC substrate. Pin-on-disc experiments were conducted by varying humidity (0%, 40% and 100%) and temperature ({minus}10 C and 25 C). As-deposited DLC and wear debris was characterized by transmission electron microscopy. It was found that lower humidity increases the graphitization rate more than likely due to the reduction in the effect by the water molecules. A decreased graphitization rate was observed at lower temperature and higher humidity and can be attributed to suppression of temperature rise at hot spots. The present findings are consistent with and further verify the wear induced graphitization mechanism.

Biofuel and Hydrogen Influence for Operation Parameters of Spark Ignition Engine

Directory of Open Access Journals (Sweden)

Martynas Damaševičius

2016-12-01

Full Text Available Paper presents research of efficient and ecological parameters of gasoline engine working with biobuthanol (10% and 20% by volume and addi-tionaly supplying oxygen and hydrogen (HHO gas mixture (3.6 l/min, which was obtained from from water by electrolysis. Biobuthanol addition decreases rate of heat release, the combustion temperature and pressure are lower, which has an influence on lower nitrous oxide (NOx emission in exhaust gases. However, biobuthanol increases carbon monoxide (CO concentration. Biobuthanol fuel has a simplier molecular structure, therefore the concentration of HC in the exhaust gas is decreasing. Due to lower heating value of biobuthanol fuel and slower combustion process, the engine efficiency decreases and specific fuel consumptions increase. The change of engine energetical indicators due to biobuthanol, can be compensated with advanced ignition angle. Using experimental investigation, it was determined, that negative biobuthanol influence for the combustion process and engine efficient inicators can be compensated also by additional supplied HHO gas, in which the hydrogen element iprove fuel mixture com-bustion. Fuel combustion process analysis was carried out using AVL BOOST software. Experimental research and combustion process numerical simulation showed that using balanced biobuthanol and hydrogen addition, optimal efficient and ecological parameters could be achieved, when engine is working for petrol fuel typical optimal spark timing.

Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness

Science.gov (United States)

Yeakub Ali, Mohammad; Banu, Asfana; Abu Bakar, Mazilah

2018-01-01

In obtaining the best quality of engineering components, the quality of machined parts surface plays an important role. It improves the fatigue strength, wear resistance, and corrosion of workpiece. This paper investigates the effects of wire electrical discharge machining (WEDM) process parameters on surface roughness of stainless steel using distilled water as dielectric fluid and brass wire as tool electrode. The parameters selected are voltage open, wire speed, wire tension, voltage gap, and off time. Empirical model was developed for the estimation of surface roughness. The analysis revealed that off time has a major influence on surface roughness. The optimum machining parameters for minimum surface roughness were found to be at a 10 V open voltage, 2.84 μs off time, 12 m/min wire speed, 6.3 N wire tension, and 54.91 V voltage gap.

Influence of Welding Parameters on the Weld Pool Dimensions and Shape in a TIG Configuration

Directory of Open Access Journals (Sweden)

Marine Stadler

2017-04-01

Full Text Available The weld pool shape created by the plasma arc interaction on a workpiece depends on many geometrical and physical parameters and on the operating conditions. Theoretical models are developed in such a way as to predict and to characterize the material. However, these models first need to be validated. Experimental results are hence proposed with parametric studies. Nevertheless, the interaction time is often short and the weld pool shape evolution not presented. In this work, the experimental setup and the diagnostic methods characterizing the workpiece are presented. The weld pool shape was evaluated versus time according to several parameters such as the current intensity value, the distance between the two electrodes, the cathode tip angle or the plasma gas nature. The results show that the depth-to-width ratio alone is not enough to compare the impact of the parameters. The analysis points out the great influence of the current intensity on the increase of the width and depth compared to the influence of the value of the cathode tip angle. The rise of the arc length leads to an increase of the power through a higher arc voltage; nevertheless, for distances of three and five millimeters and a characteristic time of the welding process of one second, this parameter has a weak influence on the energy transferred. The use of helium leads to a bigger volume of the weld pool due to an increase of width and depth.

Correlation between mass transfer coefficient kLa and relevant operating parameters in cylindrical disposable shaken bioreactors on a bench-to-pilot scale.

Science.gov (United States)

Klöckner, Wolf; Gacem, Riad; Anderlei, Tibor; Raven, Nicole; Schillberg, Stefan; Lattermann, Clemens; Büchs, Jochen

2013-12-02

Among disposable bioreactor systems, cylindrical orbitally shaken bioreactors show important advantages. They provide a well-defined hydrodynamic flow combined with excellent mixing and oxygen transfer for mammalian and plant cell cultivations. Since there is no known universal correlation between the volumetric mass transfer coefficient for oxygen kLa and relevant operating parameters in such bioreactor systems, the aim of this current study is to experimentally determine a universal kLa correlation. A Respiration Activity Monitoring System (RAMOS) was used to measure kLa values in cylindrical disposable shaken bioreactors and Buckingham's π-Theorem was applied to define a dimensionless equation for kLa. In this way, a scale- and volume-independent kLa correlation was developed and validated in bioreactors with volumes from 2 L to 200 L. The final correlation was used to calculate cultivation parameters at different scales to allow a sufficient oxygen supply of tobacco BY-2 cell suspension cultures. The resulting equation can be universally applied to calculate the mass transfer coefficient for any of seven relevant cultivation parameters such as the reactor diameter, the shaking frequency, the filling volume, the viscosity, the oxygen diffusion coefficient, the gravitational acceleration or the shaking diameter within an accuracy range of +/- 30%. To our knowledge, this is the first kLa correlation that has been defined and validated for the cited bioreactor system on a bench-to-pilot scale.

Electroconvulsive Therapy In Neuropsychiatry : Relevance Of Seizure Parameters

Directory of Open Access Journals (Sweden)

Gangadhar BN

2000-01-01

Full Text Available Electroconvulsive therapy (ECT is used to induce therapeutic seizures in various clinical conditions. It is specifically useful in depression, catatonia, patients with high suicidal risk, and those intolerant to drugs. Its beneficial effects surpass its side effects. Memory impairment is benign and transient. Its mechanism of action is unknown, though numerous neurotransmitters and neuroreceptors have been implicated. The standards of ECT practice are well established but still evolving in some particularly in unilateral ECT. Assessment of threshold by formula method may deliver higher stimulus dose compared with titration method. Cerebral seizure during ECT procedure is necessary. Motor (cuff method and EEG seizure monitoring are mandatory. Recent studies have shown some EEG parameters (amplitude, fractal dimension, symmetry, and post ictal suppression to be associated with therapeutic outcome. Besides seizure monitoring, measuring other physiological parameters such as heart rate (HR and blood pressure (BP may be useful indicators of therapeutic response. Use of ECT in neurological conditions as well as its application in psychiatric illnesses associated with neurological disorders has also been reviewed briefly.

Influence Coefficients of Constructive Parameters of Meander Slow-Wave System with Additional Shields

Directory of Open Access Journals (Sweden)

Metlevskis Edvardas

2016-12-01

Full Text Available Constructions of meander slow-wave systems with additional shields grounded at different positions are presented. The construction of meander slow-wave systems with additional shields grounded at both edges is investigated in detail. The influence of the main constructive parameters on the electrical characteristics of meander slow-wave systems with additional shields grounded at both edges is evaluated. The main constructive parameters of the investigated system are: the length of the conductor, the width of meander conductor, the width of additional shield, and the width of the gap between adjacent meander conductors.

Influence of manufacturing parameters on the strength of PLA parts using Layered Manufacturing technique: A statistical approach

Science.gov (United States)

Jaya Christiyan, K. G.; Chandrasekhar, U.; Mathivanan, N. Rajesh; Venkateswarlu, K.

2018-02-01

A 3D printing was successfully used to fabricate samples of Polylactic Acid (PLA). Processing parameters such as Lay-up speed, Lay-up thickness, and printing nozzle were varied. All samples were tested for flexural strength using three point load test. A statistical mathematical model was developed to correlate the processing parameters with flexural strength. The result clearly demonstrated that the lay-up thickness and nozzle diameter influenced flexural strength significantly, whereas lay-up speed hardly influenced the flexural strength.

Influence of coupling parameter on current-voltage characteristics of intrinsic Josephson junctions in high-T c superconductors

International Nuclear Information System (INIS)

Shukrinov, Yu.M.; Mahfouzi, F.

2006-01-01

We study the current-voltage characteristics of intrinsic Josephson junctions in high-T c superconductors by numerical calculations and in framework of capacitively coupled Josephson junctions model we obtain the total number of branches. The influence of the coupling parameter α on the current-voltage characteristics at fixed parameter β (β 2 1/β c , where β c is McCumber parameter) and the influence of α on β-dependence of the current-voltage characteristics are investigated. We obtain the α-dependence of the branch's slopes and branch's endpoints. The presented results show new features of the coupling effect on the scheme of hysteresis jumps in current-voltage characteristics of intrinsic Josephson junctions in high-T c superconductors

Influence of delayed neutron parameter calculation accuracy on results of modeled WWER scram experiments

International Nuclear Information System (INIS)

Artemov, V.G.; Gusev, V.I.; Zinatullin, R.E.; Karpov, A.S.

2007-01-01

Using modeled WWER cram rod drop experiments, performed at the Rostov NPP, as an example, the influence of delayed neutron parameters on the modeling results was investigated. The delayed neutron parameter values were taken from both domestic and foreign nuclear databases. Numerical modeling was carried out on the basis of SAPFIR 9 5andWWERrogram package. Parameters of delayed neutrons were acquired from ENDF/B-VI and BNAB-78 validated data files. It was demonstrated that using delay fraction data from different databases in reactivity meters led to significantly different reactivity results. Based on the results of numerically modeled experiments, delayed neutron parameters providing the best agreement between calculated and measured data were selected and recommended for use in reactor calculations (Authors)

Influence of various parameters on effectiveness of seismic base isolation of nuclear equipment

International Nuclear Information System (INIS)

Ebisawa, K.; Kameoka, H.; Takenouchi, I.; Kajiki, S.

1995-01-01

Authors developed a methodology and EBISA code for evaluating the applicability and the effectiveness of seismic base isolation of nuclear equipment. In order to investigate the influence of various parameters on the effectiveness of seismic base isolation, a sensitivity analysis was carried out for an emergency transformer with the base isolation devices. It was proved that seismic base isolation of equipment is very effective. This effectiveness can be influenced by the differences of the base isolation devices and the direction of the input seismic wave. (author). 7 refs., 3 figs., 3 tabs

A study on the boiler efficiency influenced by the boiler operation parameter in fossil power plant

International Nuclear Information System (INIS)

Kwon, Y. S.; Suh, J. S.

2002-01-01

The main reason to analyze the boiler operation parameter in fossil power plant is to increase boiler high efficiency and energy saving movement in the government. This study intends to have trend and analyze the boiler efficiency influenced by the boiler parameter in sub-critical and super-critical type boiler

Influencing the selectivity of zeolite Y for triglycine adsorption

NARCIS (Netherlands)

Wijntje, R.; Bosch, H.; Haan, A.B. de; Bussmann, P.J.T.

2007-01-01

In prior work we studied the adsorption of triglycine on zeolite Y under reference conditions. This study aims to solve the question of which adsorbent properties and process conditions influence the adsorption triglycine from an aqueous solution by zeolite Y. Relevant zeolite parameters to study

Investigation on influence parameters in measurements of the optomechanical hole plate using an optical coordinate measuring machine

DEFF Research Database (Denmark)

Morace, Renate Erica; Hansen, Hans Nørgaard; De Chiffre, Leonardo

2003-01-01

This paper describes the results of an experimental investigation on influence parameters in optical coordinate measurements of the optomechanical hole plate. Special attention was paid to the background of the object, which strongly influences the measurement result. Furthermore, it is seen that...... influences, the measurements were all performed with no movements of the axes of the CMM....

Stress corrosion of nickel alloys: influence of metallurgical, chemical and physicochemical parameters

International Nuclear Information System (INIS)

Gras, J.M.; Pinard-Legry, G.

1997-01-01

Stress corrosion of nickel alloys (alloys 600, X-750, 182, 82..)is the main problem of corrosion in PWR type reactors. This article gives the main knowledge about this question, considering particularly the influence of the mechanical, microstructural and physicochemical factors on cracks under stress of the alloy 600 in water at high temperature. The acquired knowledge allows nowadays to better anticipate and control the phenomenon. On the industrial point of view, they have allowed to improve the resistance of in service or future materials. While a lot of advances have been carried out in the understanding of the influence of parameters, several uncertainties still remain concerning the corrosion mechanism and the part of some factors. (O.M.)

Charges collection induced in APS by heavy particles: influence of design parameters

International Nuclear Information System (INIS)

Belredon, Xavier

2003-01-01

We have studied the design parameters influence on heavy ions-induced charge collection physics in APS. The goal is to determine the key parameters for an optimised space environment 'particle detector' APS design. It appears that diffusion is the dominant charge collection mechanism in all the studied technology types, with a smaller magnitude in case of epitaxial technologies. Following proton irradiation, a delayed charge collection and loss of collected charges have been observed. These phenomena are explained by the combination of carriers diffusion and action of the traps generated in the device. Even if they cannot be avoid in space applications, these effects are reduced in case of epitaxial technologies. This work led to the design parameters definition of an optimized APS 'particle detector' and to its fabrication. The results obtained on this APS confirm the previous conclusions and let us define the detection range of such detectors from 0.03 to 50 MeV.cm 2 .mg -1 . (author) [fr

Influence of process parameters on threshold voltage and leakage current in 18nm NMOS device

Science.gov (United States)

Atan, Norani Binti; Ahmad, Ibrahim Bin; Majlis, Burhanuddin Bin Yeop; Fauzi, Izzati Binti Ahmad

2015-04-01

The process parameters are very crucial factor in the development of transistors. There are many process parameters that influenced in the development of the transistors. In this research, we investigate the effects of the process parameters variation on response characteristics such as threshold voltage (VTH) and sub-threshold leakage current (IOFF) in 18nm NMOS device. The technique to identify semiconductor process parameters whose variability would impact most on the device characteristic is realized through the process by using Taguchi robust design method. This paper presents the process parameters that influenced in threshold voltage (VTH) and sub-threshold leakage current (IOFF) which includes the Halo Implantation, Compensation Implantation, Adjustment Threshold voltage Implantation and Source/Drain Implantation. The design, fabrication and characterization of 18nm HfO2/TiSi2 NMOS device is simulated and performed via a tool called Virtual Wafer Fabrication (VWF) Silvaco TCAD Tool known as ATHENA and ATLAS simulators. These two simulators were combined with Taguchi L9 Orthogonal method to aid in the design and the optimization of the process parameters to achieve the optimum average of threshold voltage (VTH) and sub-threshold leakage current, (IOFF) in 18nm device. Results from this research were obtained; where Halo Implantation dose was identified as one of the process parameter that has the strongest effect on the response characteristics. Whereby the Compensation Implantation dose was identified as an adjustment factor to get the nominal values of threshold voltage VTH, and sub-threshold leakage current, IOFF for 18nm NMOS devices equal to 0.302849 volts and 1.9123×10-16 A/μm respectively. The design values are referred to ITRS 2011 prediction.

Comparison of segmentation techniques to determine the geometric parameters of structured surfaces

International Nuclear Information System (INIS)

MacAulay, Gavin D; Giusca, Claudiu L; Leach, Richard K; Senin, Nicola

2014-01-01

Structured surfaces, defined as surfaces characterized by topography features whose shape is defined by design specifications, are increasingly being used in industry for a variety of applications, including improving the tribological properties of surfaces. However, characterization of such surfaces still remains an issue. Techniques have been recently proposed, based on identifying and extracting the relevant features from a structured surface so they can be verified individually, using methods derived from those commonly applied to standard-sized parts. Such emerging approaches show promise but are generally complex and characterized by multiple data processing steps making performance difficult to assess. This paper focuses on the segmentation step, i.e. partitioning the topography so that the relevant features can be separated from the background. Segmentation is key for defining the geometric boundaries of the individual feature, which in turn affects any computation of feature size, shape and localization. This paper investigates the effect of varying the segmentation algorithm and its controlling parameters by considering a test case: a structured surface for bearing applications, the relevant features being micro-dimples designed for friction reduction. In particular, the mechanisms through which segmentation leads to identification of the dimple boundary and influences dimensional properties, such as dimple diameter and depth, are illustrated. It is shown that, by using different methods and control parameters, a significant range of measurement results can be achieved, which may not necessarily agree. Indications on how to investigate the influence of each specific choice are given; in particular, stability of the algorithms with respect to control parameters is analyzed as a means to investigate ease of calibration and flexibility to adapt to specific, application-dependent characterization requirements. (paper)

INFLUENCE OF UTILIZED LOAD OF DRIVE OF COMPRESSING STATION UPON PARAMETERS OF GTP

Directory of Open Access Journals (Sweden)

A. A. Abrazovski

2014-01-01

Full Text Available Today it is required to use secondary energy resources (STR, which we have in gas-transport system of the country, more efficiently. In this system (STR smoke gases of gas transforming aggregates with turbogas drive installations are presented primarily.For using STR of turbogas drives it is necessary to forecast heat exchange equipment installation, this causes the growth of aerodynamic resistance of exhaust channel. This influences on all plant’s work. It was experimentally proved that the usage of utilized equipment influences upon increasing  of power efficiency. For this reason the perturbation method was used, which allow to determine rate of influence. Convenience of this method is that the solution can be obtained in the form of evident analytical dependence and it does not depend on formulated problem, number of variable and definite relations between them.Using the perturbation method influence efficiency was obtained, which influences on exhaust channel resistance changes and as a result changes power efficiency and in the whole plant’s efficiency. Besides, in this article the dependence of influence efficiency from stating parameters of cycle was presented in graphs: temperature of burning products before turbine and air compression.

The influence of land surface parameters on energy flux densities derived from remote sensing data

Energy Technology Data Exchange (ETDEWEB)

Tittebrand, A.; Schwiebus, A. [Inst. for Hydrology und Meteorology, TU Dresden (Germany); Berger, F.H. [Observatory Lindenberg, German Weather Service, Lindenberg (Germany)

2005-04-01

Knowledge of the vegetation properties surface reflectance, normalised difference vegetation index (NDVI) and leaf area index (LAI) are essential for the determination of the heat and water fluxes between terrestrial ecosystems and the atmosphere. Remote sensing data can be used to derive spatial estimates of the required surface properties. The determination of land surface parameters and their influence on radiant and energy flux densities is investigated with data of different remote sensing systems. Sensitivity studies show the importance of correctly derived land surface properties to estimate the key quantity of the hydrological cycle, the evapotranspiration (L.E), most exactly. In addition to variable parameters like LAI or NDVI there are also parameters which are can not be inferred from satellite data but needed for the Penman-Monteith approach. Fixed values are assumed for these variables because they have little influence on L.E. Data of Landsat-7 ETM+ and NOAA-16 AVHRR are used to show results in different spatial resolution. The satellite derived results are compared with ground truth data provided by the Observatory Lindenberg of the German Weather Service. (orig.)

THE INFLUENCE OF THE TOOL POINT ANGLE AND FEED RATE ON THE DYNAMIC PARAMETERS AT DRILLING COATED PARTICLEBOARD

Directory of Open Access Journals (Sweden)

Mihai ISPAS

2015-12-01

Full Text Available Pre-laminated (coated particleboards (PB are wood-based composites intensively used in the furniture industry. In order to prepare the PB for joining, drilling is the most commonly applied machining process. The surface quality and the dynamic parameters (thrust force and torque are significantly influenced by the tools characteristics and the machining parameters. The point/tip angle of the drill bit and the feed speed during drilling play a major role in gaining a good surface quality and minimizing the dynamic parameters. The objective of this study was to measure and analyze the influence of both the geometric and cinematic parameters on the dynamic parameters at drilling with twist (helical drills. The experiments were performed based on a factorial design. The results show that, a low feed rate generally minimizes both the drilling torque and the thrust force, while a small tip angle increases the drilling torque and minimizes the thrust force.

SITE-94. Chemical and physical transport parameters for SITE-94

Energy Technology Data Exchange (ETDEWEB)

Andersson, Karin [Chalmers Univ. of Technology, Goeteborg (Sweden). Technical Environmental Planning

1996-02-01

Important parameters are the interactions of radionuclides with solid surfaces, parameters describing the geometrical conditions like porosity, data on water composition (ionic strength, pH, redox conditions, complex formers etc) and data on the solids that may be of importance to the water and radionuclide chemistry. In this report some of these data of relevance for the Aespoe site are discussed. Based on a literature survey, sorption data as well as values for some other parameters have been selected for rock, fracture fillings and bentonite relevant to the chemical conditions in and around a repository at Aespoe. A comparison to data used for earlier, site-specific as well as general, safety assessments of underground repositories has been performed. The data are recommendations for modelling of radionuclide release from a hypothetical high level waste repository at Aespoe. Since the data to a large extent are not based on experimental measurements, more accurate predictions may be expected if more experimental data are available. Before such studies are performed for a specific site, a variational analysis in order to evaluate the importance of the single parameters is recommended. After such a study, the key parameters may be investigated in detail and the modelling can be expected to be more accurate what concerns influence of single parameters. However, the uncertainty in conceptual areas like how to model accurately the long term hydrology of the site etc still remains. 32 refs.

Influence of flowfield and vehicle parameters on engineering aerothermal methods

Science.gov (United States)

Wurster, Kathryn E.; Zoby, E. Vincent; Thompson, Richard A.

1989-01-01

The reliability and flexibility of three engineering codes used in the aerosphace industry (AEROHEAT, INCHES, and MINIVER) were investigated by comparing the results of these codes with Reentry F flight data and ground-test heat-transfer data for a range of cone angles, and with the predictions obtained using the detailed VSL3D code; the engineering solutions were also compared. In particular, the impact of several vehicle and flow-field parameters on the heat transfer and the capability of the engineering codes to predict these results were determined. It was found that entropy, pressure gradient, nose bluntness, gas chemistry, and angle of attack all affect heating levels. A comparison of the results of the three engineering codes with Reentry F flight data and with the predictions obtained of the VSL3D code showed a very good agreement in the regions of the applicability of the codes. It is emphasized that the parameters used in this study can significantly influence the actual heating levels and the prediction capability of a code.

Factors that Influence the Perceived Advantages and Relevance of Facebook as a Learning Tool: An Extension of the UTAUT

Science.gov (United States)

Escobar-Rodríguez, Tomás; Carvajal-Trujillo, Elena; Monge-Lozano, Pedro

2014-01-01

Social media technologies are becoming a fundamental component of education. This study extends the Unified Theory of Acceptance and Use of Technology (UTAUT) to identify factors that influence the perceived advantages and relevance of Facebook as a learning tool. The proposed model is based on previous models of UTAUT. Constructs from previous…

Influence of the P content on the transport parameters of hydrogen in Fe alloys

Energy Technology Data Exchange (ETDEWEB)

Peñalva, I., E-mail: igor.penalva@ehu.es [University of the Basque Country (UPV/EHU), Department of Nuclear Engineering & Fluid Mechanics, Faculty of Engineering, Alda. Urquijo s/n, 48013 Bilbao (Spain); Alberro, G.; Legarda, F. [University of the Basque Country (UPV/EHU), Department of Nuclear Engineering & Fluid Mechanics, Faculty of Engineering, Alda. Urquijo s/n, 48013 Bilbao (Spain); Ortiz, C.J.; Vila, R. [CIEMAT, Avda. Complutense 22, 28040 Madrid (Spain)

2015-10-15

Highlights: • Gas permeation technique was used to study hydrogen diffusive transport parameters. • Four Fe alloys were analyzed to study the influence of the P content. • Increase in the P content leads to smaller values of permeability and diffusivity. • Trapping effects were observed at temperatures below 473 K for alloys containing P. - Abstract: In this work, the hydrogen transport parameters of permeability (ϕ), diffusivity (D) and Sieverts’ constant (K{sub S}) were experimentally measured in four Fe alloys supplied by the European Fusion Development Agreement (EFDA), by means of the gas evolution permeation technique. The samples had controlled chemical alloying element contents and microstructure. The experimental temperature range explored was from 423 K to 823 K and the high purity hydrogen loading pressures from 10{sup 3} Pa to 1.5·10{sup 5} Pa. The main objective of this work was to determine the influence of the P content of the alloy in the transport parameters of hydrogen. Two of the samples, pure Fe and FeC, contained negligible quantities of P (less than 5 ppm in weight), whereas the other two, FeP and FeCP, had the same metallurgical composition as their corresponding pair, with the only difference in the phosphorus content (89 ppm in weight and 88 ppm in weight, respectively). The experimental permeation results were analyzed using a non-linear least square fitting. The final resulting values of the aforementioned transport parameters were paired off in order to determine the effect of the P content: pure Fe versus FeP and FeC versus FeCP. We observed that the permeability obtained for all the samples follows an Arrhenius law in each case. In general terms, the increase of the P content in the alloy leads to smaller values of the permeability showing a decrease in the permeation activation energy. Regarding diffusivity and Sieverts’ constant, trapping effects have been observed for the alloys containing P. This phenomenon was

Influence of Dissipative Particle Dynamics parameters and wall models on planar micro-channel flows

Science.gov (United States)

Wang, Yuyi; She, Jiangwei; Zhou, Zhe-Wei; microflow Group Team

2017-11-01

Dissipative Particle Dynamics (DPD) is a very effective approach in simulating mesoscale hydrodynamics. The influence of solid boundaries and DPD parameters are typically very strong in DPD simulations. The present work studies a micro-channel Poisseuille flow. Taking the neutron scattering experiment and molecular dynamics simulation result as bench mark, the DPD results of density distribution and velocity profile are systematically studied. The influence of different levels of coarse-graining, the number densities of wall and fluid, conservative force coefficients, random and dissipative force coefficients, different wall model and reflective boundary conditions are discussed. Some mechanisms behind such influences are discussed and the artifacts in the simulation are identified with the bench mark. Chinese natural science foundation (A020405).

Influence of process parameters on the weld lines of a micro injection molded component

DEFF Research Database (Denmark)

Tosello, Guido; Gava, Alberto; Hansen, Hans Nørgaard

2007-01-01

The insufficient entanglement of the molecular chains and the stress amplification at the v-notch of a weld line compromise the mechanical strength of a plastic product, also in the micro scale. To investigate the influence of process parameters on the weld lines formation, a special micro cavity...... was designed and manufactured by µEDM (Electro Discharge Machining). Weld lines were quantitatively characterized both in the two-dimensional (direction and position) and three-dimensional range (surface topography characterization). Results showed that shape and position of weld lines are mainly influenced...

BACTERIAL LEACHING OF ELECTRONIC SCRAP: INFLUENCE OF PROCESS PARAMETERS

Directory of Open Access Journals (Sweden)

Luciana Harue Yamane

2013-03-01

Full Text Available The application of bacterial leaching in the ore treatment is already known and also can be applied such as treatment of electronic waste to copper recovery. This paper investigates the influence of process parameters (pulp density, inoculums volume, rotation speed and initial concentration of ferrous iron on bacterial leaching of copper from printed circuit board of computers using the bacterium Acidithiobacillus ferrooxidans–LR. Printed circuit boards from computers were comminuted using a hammer mill. The powder obtained was magnetically separated and the non-magnetic material used in this study. A shake flask study was carried out on the non-magnetic material using a shaker. The results show that Acidithiobacillus ferrooxidans–LR can leach 99% of copper from printed circuit boards (non–magnetic material under the determined conditions through of the studies.

Contribution to the analysis of the influence of parameters of elasto-damping elements to the vehicle ride comfort

Directory of Open Access Journals (Sweden)

Demić Miroslav D.

2017-01-01

Full Text Available During development of motor vehicles, a significant role has a dynamic simulation, which is based on the modeling. Role modeling is very important in the early stages of design, during definition of the vehicles main parameters. Literature sources provide complete responses to the influence of the forces in springs, shock absorbers and tires on the vehicle oscillatory comfort, but hardly anyone engaged in analysis of parameters of the models of elasto-damping elements on the oscillations of the vehicle. This paper will attempt to be made, on the basis of the adopted models of springs, shock absorbers and tires, perform analysis of the influence of parameters on the oscillations of the vehicle. For that purpose they used so-called sensitivity functions.

The influence of the surface parameter changes onto the phonon states in ultrathin crystalline films

Science.gov (United States)

Šetrajčić, Jovan P.; Ilić, Dušan I.; Jaćimovski, Stevo K.

2018-04-01

In this paper, we have analytically investigated how the changes in boundary surface parameters influence the phonon dispersion law in ultrathin films of the simple cubic crystalline structure. Spectra of possible phonon states are analyzed using the method of two-time dependent Green's functions and for the diverse combination of boundary surface parameters, this problem was presented numerically and graphically. It turns out that for certain values and combinations of parameters, displacement of dispersion branches outside of bulk zone occurs, leading to the creation of localized phonon states. This fact is of great importance for the heat removal, electrical conductivity and superconducting properties of ultrathin films.

Dietary supplementation of tiger nut alters biochemical parameters relevant to erectile function in l-NAME treated rats.

Science.gov (United States)

Olabiyi, Ayodeji A; Carvalho, Fabiano B; Bottari, Nathieli B; Lopes, Thauan F; da Costa, Pauline; Stefanelo, Naiara; Morsch, Vera M; Akindahunsi, Afolabi A; Oboh, Ganiyu; Schetinger, Maria Rosa

2018-07-01

Tiger nut tubers have been reportedly used for the treatment of erectile dysfunction (ED) in folk medicine without scientific basis. Hence, this study evaluated the effect of tiger nut on erectile dysfunction by assessing biochemical parameters relevant to ED in male rats by nitric oxide synthase (NOS) inhibitor, Nω-nitro-l-arginine methyl ester hydrochloride (l-NAME) treatment. Rats were divided into five groups (n = 10) each: Control group; l-NAME plus basal diet; l-NAME plus Sildenafil citrate; diet supplemented processed tiger nut (20%) plus l-NAME;diet supplemented raw tiger nut (20%) plus l-NAME. l-NAME pre-treatment (40 mg/kg/day) lasted for 14 days. Arginase, acetycholinesterase (AChE) and adenosine deaminase (ADA) activities as well as nitric oxide levels (NO) in serum, brain and penile tissue were measured. l-NAME increased the activity of arginase, AChE and ADA and reduced NO levels. However, dietary supplementation with tiger nut caused a reduction on the activities of the above enzymes and up regulated nitric oxide levels when compared to the control group. The effect of tiger nut supplemented diet may be said to prevent alterations of the activities of the enzymes relevant in erectile function. Quercetin was revealed to be the most active component of tiger nut tuber by HPLC finger printing. Copyright © 2018. Published by Elsevier Ltd.

Influence of geometrical parameters of the VVER-1000 reactor construction elements to internals irradiation conditions

Directory of Open Access Journals (Sweden)

О. M. Pugach

2015-07-01

Full Text Available Investigations to determine the influences of geometrical parameters of the calculational VVER-1000 reactor model to the results of internal irradiation condition determination are carried out. It is shown that the values of appropriate sensitivity matrix elements are not dependent on a height coordinate for any core level, but there is their azimuthal dependence. Maximum possible relative biases of neutron fluence due to inexact knowledge of internal geometrical parameters are obtained for the baffle and the barrel.

Influence of Impurities on the Fuel Retention in Fusion Reactors

OpenAIRE

Reinhart, Michael

2015-01-01

The topic of this thesis is the influence of plasma impurities on the hydrogen retentionin metals, in the scope of plasma-wall-interaction research for fusion reactors.This is addressed experimentally and by modelling. The mechanisms of the hydrogenretention are influenced by various parameters like the wall temperature, ionenergy, flux and fluence as well as the plasma composition. The plasma compositionis a relevant factor for hydrogen retention in fusion reactors, as their plasma willalso ...

A study on the relevance and influence of the existing regulation and risk informed/performance based regulation

Energy Technology Data Exchange (ETDEWEB)

Cheong, B. J.; Koh, Y. J.; Kim, H. S.; Koh, S. H.; Kang, D. H.; Kang, T. W. [Cheju National Univ., Jeju (Korea, Republic of)

2004-02-15

The goal of this study is to estimate the Relevance and Influence of the Existing Regulation and the RI-PBR to the institutionalization of the regulatory system. This study reviews the current regulatory system and the status of the RI-PBR implementation of the US NRC and Korea based upon SECY Papers, Risk Informed Regulation Implementation Plan (RIRIP) of the US NRC and other domestic studies. Also the recent trends of the individual technologies regarding the RI-PBR and RIA are summarized.

Influence analysis of design parameters of suspensions on the technical specifications of conveyor with suspended belt and distributed drive

Directory of Open Access Journals (Sweden)

Lagerev A.V.

2016-09-01

Full Text Available Using the basic design of the conveyor with suspended belt and distributed drive, a series of numerical calculations was performed. As a result, the influence of friction and mass-dimensional design parameters of suspensions on the main technical parameters of the conveyor was established. Recommendations on the choice of rational parameters were formulated.

The influence of technological parameters on the dynamic behavior of "liquid wood" samples obtained by injection molding

Science.gov (United States)

Plavanescu Mazurchevici, Simona; Carausu, Constantin; Comaneci, Radu; Nedelcu, Dumitru

2017-10-01

The plastic products contribute to environmental pollution. Replacing the plastic materials with biodegradable materials with superior properties is an absolute necessity and important research direction for the near future. The first steps in this regard were the creation of composite materials containing natural fibers with positive effects on the environment that have penetrated in different fields. The bioplastics and biocomposites made from natural fibers is a topical solution. The next step was made towards obtaining biodegradable and recyclable materials based on cellulose, lignin and no carcinogens. In this category fall the "liquid wood" with a use up to five times without affecting the mechanical properties. "Liquid wood" is a high quality thermoplastic biocomposite. "Liquid wood" is a biopolymer composite divided in three categories, ARBOFORM®, ARBOBLEND® and ARBOFILL®, which have differed composition in terms of lignin percentage, being delivered by Tecnaro, as granules, [1]. The paper's research was focus on Arboform L V3 Nature and Arboform L V3 Nature reinforced with aramid fiber. In the experimental plan were taken into account six parameters (Dinj - direction of injection [°]; Ttop - melting temperature [°C]; Pinj - injection pressure [MPa] Ss - speed [m/min]; tinj - injection time [s] and tc - cooling time [s]) each with two levels, research carried on by Taguchi methodology. Processing Taguchi method allowed both Taguchi setting work parameters influence on storage modulus and damping as the size and influence their ranking. Experimental research concerning the influence technological parameters on storage modulus of samples obtained by injection from Arboform L V3 Nature yielded an average of 6055MPa and descending order as follows: Trac, Ss, Pinj, Dinj and Ttop. The average of model for reinforced material was 6419MPa and descending order of parameters influence such as: Dinj, Trac, Ttop, tinj, Ss and Pinj.

THE INFLUENCE OF ADDITIVES FOR QUALITATIVE PARAMETERS OF SILAGE FEEDS

Directory of Open Access Journals (Sweden)

F. LÁD

2007-05-01

Full Text Available We observed the influence of silage additives for choice qualitative parameters at clover-grass silages in working conditions. We evaluated total classification and categorization to quality classes according to fermentative process. It has been found out positive effect of the silage additives for fermentative class and for total silage quality of silages. This positive effect has been more considerable at the classification to the fermentative classes at clover-grass silages. The high content of crude fibre decreased fermentative results and total silage quality at test clovergrass silages. The greatest (deterioration influence for clasification to total quality class has crude fibre content. It is see from correlation coefficient at clover-grass silages r = 0.75 (P < 0.05. The weak dependence r = 0.37 (P < 0.05 was detected between fermentative class and acetic acid content. It was detected large dependence between fermentative class and butyric acid content r = 0.73 (P < 0.05. The silages with additives had better degree of proteolysis and higher value of lactic acid. The additive improved fermentative quality. The result of better fermentative process was reduction of crude fibre values with maintainance of energy content.

Different atmospheric parameters influence on spectral UV radiation (measurements and modelling)

Energy Technology Data Exchange (ETDEWEB)

Chubarova, N Y [Moscow State Univ. (Russian Federation). Meteorological Observatory; Krotkov, N A [Maryland Univ., MD (United States). JCESS/Meteorology Dept.; Geogdzhaev, I V; Bushnev, S V; Kondranin, T V [SUMGF/MIPT, Dolgoprudny (Russian Federation); Khattatov, V U [Central Aerological Observatory, Dolgoprudny (Russian Federation)

1996-12-31

The ultraviolet (UV) radiation plays a vital role in the biophysical processes despite its small portion in the total solar flux. UV radiation is subject to large variations at the Earth surface depending greatly on solar elevation, ozone and cloud amount, aerosols and surface albedo. The analysis of atmospheric parameters influence is based on the spectral archive data of three spectral instruments: NSF spectroradiometer (Barrow network) (NSF Polar Programs UV Spectroradiometer Network 1991-1992,1992), spectrophotometer (SUVS-M) of Central Aerological Observatory CAO, spectroradiometer of Meteorological Observatory of the Moscow State University (MO MSU) and model simulations based on delta-Eddington approximation

Different atmospheric parameters influence on spectral UV radiation (measurements and modelling)

Energy Technology Data Exchange (ETDEWEB)

Chubarova, N.Y. [Moscow State Univ. (Russian Federation). Meteorological Observatory; Krotkov, N.A. [Maryland Univ., MD (United States). JCESS/Meteorology Dept.; Geogdzhaev, I.V.; Bushnev, S.V.; Kondranin, T.V. [SUMGF/MIPT, Dolgoprudny (Russian Federation); Khattatov, V.U. [Central Aerological Observatory, Dolgoprudny (Russian Federation)

1995-12-31

The ultraviolet (UV) radiation plays a vital role in the biophysical processes despite its small portion in the total solar flux. UV radiation is subject to large variations at the Earth surface depending greatly on solar elevation, ozone and cloud amount, aerosols and surface albedo. The analysis of atmospheric parameters influence is based on the spectral archive data of three spectral instruments: NSF spectroradiometer (Barrow network) (NSF Polar Programs UV Spectroradiometer Network 1991-1992,1992), spectrophotometer (SUVS-M) of Central Aerological Observatory CAO, spectroradiometer of Meteorological Observatory of the Moscow State University (MO MSU) and model simulations based on delta-Eddington approximation

Transient radiation responses of optical fibers: influence of MCVD process parameters

International Nuclear Information System (INIS)

Girard, Sylvain; Alessi, Antonino; Boukenter, Aziz; Ouerdane, Y.; Marcandella, Claude; Richard, Nicolas; Paillet, Philippe; Gaillardin, Marc; Raine, Melanie

2012-01-01

A dedicated set of fibers elaborated via the Modified Chemical Vapor Deposition (MCVD) technique is used to study the influence of composition and drawing parameters on their responses to an X-ray pulse representative of the radiation environments associated with Megajoule class lasers. These canonical fibers were designed to highlight the impact of these parameters on the amplitude and kinetics of the transient pulsed X-ray Radiation Induced Attenuation (RIA) at room temperature. From pre-forms differing by their core composition, three optical fibers were elaborated by varying the tension and speed during the drawing process. No or only slight RIA change results from the tested variations in drawing process parameters of Ge-doped, F-doped, and pure-silica-core fibers. This study reveals that the drawing process is not the main parameter to be optimized in order to enhance the radiation tolerance of MCVD specialty optical fibers for the LMJ harsh environment. From the hardness assurance point of view, a specialty fiber sufficiently tolerant to this environment should be robust against changes in the drawing process. The origins of the RIA observed in the different fibers are discussed on the basis of spectral decomposition of their measured RIA spectra, using sets of defects from the literature and related to the different core dopants. This analysis highlights the limits of the well-known defect set to reproduce the RIA above 1 for Ge-doped fibers whereas self-trapped holes and chlorine-related species seem responsible for the transient responses of pure-silica-core and F-doped fibers. (authors)

ANOVA parameters influence in LCF experimental data and simulation results

Directory of Open Access Journals (Sweden)

Vercelli A.

2010-06-01

Full Text Available The virtual design of components undergoing thermo mechanical fatigue (TMF and plastic strains is usually run in many phases. The numerical finite element method gives a useful instrument which becomes increasingly effective as the geometrical and numerical modelling gets more accurate. The constitutive model definition plays an important role in the effectiveness of the numerical simulation [1, 2] as, for example, shown in Figure 1. In this picture it is shown how a good cyclic plasticity constitutive model can simulate a cyclic load experiment. The component life estimation is the subsequent phase and it needs complex damage and life estimation models [3-5] which take into account of several parameters and phenomena contributing to damage and life duration. The calibration of these constitutive and damage models requires an accurate testing activity. In the present paper the main topic of the research activity is to investigate whether the parameters, which result to be influent in the experimental activity, influence the numerical simulations, thus defining the effectiveness of the models in taking into account of all the phenomena actually influencing the life of the component. To obtain this aim a procedure to tune the parameters needed to estimate the life of mechanical components undergoing TMF and plastic strains is presented for commercial steel. This procedure aims to be easy and to allow calibrating both material constitutive model (for the numerical structural simulation and the damage and life model (for life assessment. The procedure has been applied to specimens. The experimental activity has been developed on three sets of tests run at several temperatures: static tests, high cycle fatigue (HCF tests, low cycle fatigue (LCF tests. The numerical structural FEM simulations have been run on a commercial non linear solver, ABAQUS®6.8. The simulations replied the experimental tests. The stress, strain, thermal results from the thermo

The Influence on Modal Parameters of Thin Cylindrical Shell under Bolt Looseness Boundary

Directory of Open Access Journals (Sweden)

Hui Li

2016-01-01

Full Text Available The influence on modal parameters of thin cylindrical shell (TCS under bolt looseness boundary is investigated. Firstly, bolt looseness boundary of the shell is divided into two types, that is, different bolt looseness numbers and different bolt looseness levels, and natural frequencies and mode shapes are calculated by finite element method to roughly master vibration characteristics of TCS under these conditions. Then, the following measurements and identification techniques are used to get precise frequency, damping, and shape results; for example, noncontact laser Doppler vibrometer and vibration shaker with excitation level being precisely controlled are used in the test system; “preexperiment” is adopted to determine the required tightening torque and verify fixed constraint boundary; the small-segment FFT processing technique is employed to accurately measure nature frequency and laser rotating scanning technique is used to get shape results with high efficiency. Finally, based on the measured results obtained by the above techniques, the influence on modal parameters of TCS under two types of bolt looseness boundaries is analyzed and discussed. It can be found that bolt looseness boundary can significantly affect frequency and damping results which might be caused by changes of nonlinear stiffness and damping and in bolt looseness positions.

Variation of biometric parameters in corn cobs under the influence of nitrogen fertilization

Science.gov (United States)

Gigel, Prisecaru; Florin, Sala

2017-07-01

Biometric parameters as elements of productivity on corn cobs, along with plant density per unit area (ha) are essential in achieving production. The influence of differentiated fertilization with nitrogen was evaluated at the level of productivity elements on corn cobs, Andreea hybrid. Biometric parameters of the corn cobs (total length - L; usable length - l; uncoated length with corn kernels - lu; diameter at the base - Db, middle - Dm, and top of the corn cobs - Dt; corn cob weight - Cw, grain weight - Gw) were directly influenced by the doses of nitrogen. Regression analysis has facilitated the prediction of grain weight as the main element of productivity under different statistical certainty based on nitrogen doses (R2 = 0.962, p<0.01), on the total length of corn cobs (R2 = 0.985, p<0.01), on the usable length of corn cobs (R2 = 0.996, p<<0.001), on the diameter at the base of corn cobs (R2 = 0.824, p<0.01), on the diameter at the middle of corn cobs (R2 = 0.807, p<0.01), on uncoated length with corn kernels (R2 = 0.624, p<0.01) and on the diameter at the top of the corn cobs (R2 = 0.384, p=0.015).

Influence of puerperal gonadoreline application on reproductive parameter values in cows

Directory of Open Access Journals (Sweden)

Šabanović Mustafa

2006-01-01

Full Text Available This paper presents results of investigations conducted in order to investigate the influence of gonadoreline application 14-16, 17-20 and 21-25 days postpartum on reproductive parameters values in cows. A total of 241 cows was included in the study. Out of this number, 126 cows were treated with gonadoreline while 115 animals were placebo treated and served as controls. The estimation of progesterone concentration was conducted on 43 animals selected randomly from the first two groups of treated cows. Analyses of the results in cows that gave normal birth, revealed that mean anoestrus period, open day's period and intervals between calving were significantly lower in the gonadoreline treated groups. Reproductive parameter values in cows with different progesterone concentrations did not differ significantly. The period from gonadoreline application until conception, was shorter by 30, 30 and 14 days, respectively, compared to the controls. The total conception rate from the first three artificial inseminations was 88. 8% in gonadoreline treated groups and 83.47 % in the control groups.

Powder properties and compaction parameters that influence punch sticking propensity of pharmaceuticals.

Science.gov (United States)

Paul, Shubhajit; Taylor, Lisa J; Murphy, Brendan; Krzyzaniak, Joseph F; Dawson, Neil; Mullarney, Matthew P; Meenan, Paul; Sun, Changquan Calvin

2017-04-15

Punch sticking is a frequently occurring problem that challenges successful tablet manufacturing. A mechanistic understanding of the punch sticking phenomenon facilitates the design of effective strategies to solve punch sticking problems of a drug. The first step in this effort is to identify process parameters and particle properties that can profoundly affect sticking performance. This work was aimed at elucidating the key material properties and compaction parameters that influence punch sticking by statistically analyzing punch sticking data of 24 chemically diverse compounds obtained using a set of tooling with removable upper punch tip. Partial least square (PLS) analysis of the data revealed that particle surface area and tablet tensile strength are the most significant factors attributed to punch sticking. Die-wall pressure, ejection force, and take-off force also correlate with sticking, but to a lesser extent. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of La and Sr addition on the structural parameter of PbTiO3

International Nuclear Information System (INIS)

Garcia, D.; Mascarenhas, Y.P.; Oliveira Paiva Santos, C. de; Eiras, J.A.

1989-01-01

Compositions of (Pb 1-x Ln x ) (Ti 1-y Mn y )O 3 (Ln = La, Sr; 0 0 C and sintered at 1200 0 C. The influence of the adition of La and Sr in the structural parameters of the tetragonal lattice of the lead titanate (PbTiO 3 ) was investigated with X-ray diffraction. The doping, with La or Sr, increase the lattice parameter a and decrease de parameter c of the PbTiO 3 . The variation of a and c increase with the dopant concentration and is greather in the La doped samples. The addition of 1% mol of Mn in these compositions increase the their sinterability. The apparent densites were compared with those calculated from the lattice parameters a and c. A decrease of the Curie temperature T c was observed when the concentration of La or Sr was increased. (author) [pt

Technological parameters influence on the non-autoclaved foam concrete characteristics

Science.gov (United States)

Bartenjeva, Ekaterina; Mashkin, Nikolay

2017-01-01

Foam concretes are used as effective heat-insulating materials. The porous structure of foam concrete provides good insulating and strength properties that make them possible to be used as heat-insulating structural materials. Optimal structure of non-autoclaved foam concrete depends on both technological factors and properties of technical foam. In this connection, the possibility to manufacture heat-insulation structural foam concrete on a high-speed cavity plant with the usage of protein and synthetic foamers was estimated. This experiment was carried out using mathematical planning method, and in this case mathematical models were developed that demonstrated the dependence of operating performance of foam concrete on foaming and rotation speed of laboratory plant. The following material properties were selected for the investigation: average density, compressive strength, bending strength and thermal conductivity. The influence of laboratory equipment technological parameters on technical foam strength and foam stability coefficient in the cement paste was investigated, physical and mechanical properties of non-autoclaved foam concrete were defined based on investigated foam. As a result of investigation, foam concrete samples were developed with performance parameters ensuring their use in production. The mathematical data gathered demonstrated the dependence of foam concrete performance on the technological regime.

Some relevant parameters for assessing fire hazards of combustible mine materials using laboratory scale experiments.

Science.gov (United States)

Litton, Charles D; Perera, Inoka E; Harteis, Samuel P; Teacoach, Kara A; DeRosa, Maria I; Thomas, Richard A; Smith, Alex C

2018-04-15

When combustible materials ignite and burn, the potential for fire growth and flame spread represents an obvious hazard, but during these processes of ignition and flaming, other life hazards present themselves and should be included to ensure an effective overall analysis of the relevant fire hazards. In particular, the gases and smoke produced both during the smoldering stages of fires leading to ignition and during the advanced flaming stages of a developing fire serve to contaminate the surrounding atmosphere, potentially producing elevated levels of toxicity and high levels of smoke obscuration that render the environment untenable. In underground mines, these hazards may be exacerbated by the existing forced ventilation that can carry the gases and smoke to locations far-removed from the fire location. Clearly, materials that require high temperatures (above 1400 K) and that exhibit low mass loss during thermal decomposition, or that require high heat fluxes or heat transfer rates to ignite represent less of a hazard than materials that decompose at low temperatures or ignite at low levels of heat flux. In order to define and quantify some possible parameters that can be used to assess these hazards, small-scale laboratory experiments were conducted in a number of configurations to measure: 1) the toxic gases and smoke produced both during non-flaming and flaming combustion; 2) mass loss rates as a function of temperature to determine ease of thermal decomposition; and 3) mass loss rates and times to ignition as a function of incident heat flux. This paper describes the experiments that were conducted, their results, and the development of a set of parameters that could possibly be used to assess the overall fire hazard of combustible materials using small scale laboratory experiments.

Estimate the contribution of incubation parameters influence egg hatchability using multiple linear regression analysis.

Science.gov (United States)

Khalil, Mohamed H; Shebl, Mostafa K; Kosba, Mohamed A; El-Sabrout, Karim; Zaki, Nesma

2016-08-01

This research was conducted to determine the most affecting parameters on hatchability of indigenous and improved local chickens' eggs. Five parameters were studied (fertility, early and late embryonic mortalities, shape index, egg weight, and egg weight loss) on four strains, namely Fayoumi, Alexandria, Matrouh, and Montazah. Multiple linear regression was performed on the studied parameters to determine the most influencing one on hatchability. The results showed significant differences in commercial and scientific hatchability among strains. Alexandria strain has the highest significant commercial hatchability (80.70%). Regarding the studied strains, highly significant differences in hatching chick weight among strains were observed. Using multiple linear regression analysis, fertility made the greatest percent contribution (71.31%) to hatchability, and the lowest percent contributions were made by shape index and egg weight loss. A prediction of hatchability using multiple regression analysis could be a good tool to improve hatchability percentage in chickens.

Influence of deposition parameters on the refractive index and growth rate of diamond-like carbon films

International Nuclear Information System (INIS)

Zhang, G.F.; Zheng, X.; Guo, L.J.; Liu, Z.T.; Xiu, N.K.

1994-01-01

In order to use diamond-like carbon (DLC) films as protective and antireflection coatings for IR optical materials exposed to hostile environments, an investigation has been systematically conducted on the influence of the deposition parameters on the refractive index and growth rate of DLC films, which are two of the most important parameters in evaluating optical characteristics of antireflection coatings. The experimental results show that both the refractive index and growth rate of DLC films depend strongly on the negative d.c. bias voltage. The refractive index increases with increasing bias voltage and decreases with increasing partial pressure of the hydrocarbon gas and total flow rate of the mixture. The growth rate increases greatly when the bias voltage is larger than a threshold value. The various parameters which influence the structure and properties of DLC films are interrelated. Fourier transform IR spectroscopy results show that the strength of the C-H stretching absorption band in the range 3300-2850 cm -1 is gradually weakened with increasing negative bias voltage and argon concentration. High energy bombardment of the growing film plays an important role in the structure and hence the properties of DLC films. (orig.)

The Influence of the Axial Magnetic Field Upon-the Coaxial Plasma Gun Parameters

International Nuclear Information System (INIS)

El-Aragi, G.M.; EL-Demrdash, A.

2001-01-01

This study concerns with the influence of an applied axial magnetic field upon the electrical parameters of a coaxial plasma gun device. The experimental results are investigated with 0.5 KJ plasma gun device operated with argon gas at a pressure of 3.5 Torr. An axial time independent magnetic field with intensity of 550 G is introduced along the plasma current sheath axial region, within the annular space between the two coaxial electrodes. From the measurements of the discharge current I(t) and the voltage V(t), the electrical discharge parameters of the plasma gun device and the plasma current sheath implosion velocity are estimated, in normal mode of plasma gun operation and in the mode of presence external axial magnetic field. A comparison between these two modes is studied

Influence of parameter values on the oscillation sensitivities of two p53-Mdm2 models.

Science.gov (United States)

Cuba, Christian E; Valle, Alexander R; Ayala-Charca, Giancarlo; Villota, Elizabeth R; Coronado, Alberto M

2015-09-01

Biomolecular networks that present oscillatory behavior are ubiquitous in nature. While some design principles for robust oscillations have been identified, it is not well understood how these oscillations are affected when the kinetic parameters are constantly changing or are not precisely known, as often occurs in cellular environments. Many models of diverse complexity level, for systems such as circadian rhythms, cell cycle or the p53 network, have been proposed. Here we assess the influence of hundreds of different parameter sets on the sensitivities of two configurations of a well-known oscillatory system, the p53 core network. We show that, for both models and all parameter sets, the parameter related to the p53 positive feedback, i.e. self-promotion, is the only one that presents sizeable sensitivities on extrema, periods and delay. Moreover, varying the parameter set values to change the dynamical characteristics of the response is more restricted in the simple model, whereas the complex model shows greater tunability. These results highlight the importance of the presence of specific network patterns, in addition to the role of parameter values, when we want to characterize oscillatory biochemical systems.

Numerical Methods for a Multicomponent Two-Phase Interface Model with Geometric Mean Influence Parameters

KAUST Repository

Kou, Jisheng

2015-07-16

In this paper, we consider an interface model for multicomponent two-phase fluids with geometric mean influence parameters, which is popularly used to model and predict surface tension in practical applications. For this model, there are two major challenges in theoretical analysis and numerical simulation: the first one is that the influence parameter matrix is not positive definite; the second one is the complicated structure of the energy function, which requires us to find out a physically consistent treatment. To overcome these two challenging problems, we reduce the formulation of the energy function by employing a linear transformation and a weighted molar density, and furthermore, we propose a local minimum grand potential energy condition to establish the relation between the weighted molar density and mixture compositions. From this, we prove the existence of the solution under proper conditions and prove the maximum principle of the weighted molar density. For numerical simulation, we propose a modified Newton\\'s method for solving this nonlinear model and analyze its properties; we also analyze a finite element method with a physical-based adaptive mesh-refinement technique. Numerical examples are tested to verify the theoretical results and the efficiency of the proposed methods.

Numerical Methods for a Multicomponent Two-Phase Interface Model with Geometric Mean Influence Parameters

KAUST Repository

Kou, Jisheng; Sun, Shuyu

2015-01-01

In this paper, we consider an interface model for multicomponent two-phase fluids with geometric mean influence parameters, which is popularly used to model and predict surface tension in practical applications. For this model, there are two major challenges in theoretical analysis and numerical simulation: the first one is that the influence parameter matrix is not positive definite; the second one is the complicated structure of the energy function, which requires us to find out a physically consistent treatment. To overcome these two challenging problems, we reduce the formulation of the energy function by employing a linear transformation and a weighted molar density, and furthermore, we propose a local minimum grand potential energy condition to establish the relation between the weighted molar density and mixture compositions. From this, we prove the existence of the solution under proper conditions and prove the maximum principle of the weighted molar density. For numerical simulation, we propose a modified Newton's method for solving this nonlinear model and analyze its properties; we also analyze a finite element method with a physical-based adaptive mesh-refinement technique. Numerical examples are tested to verify the theoretical results and the efficiency of the proposed methods.

Systematic study of influence of growth parameters on island morphology during molecular beam epitaxy growth: A Monte Carlo study

International Nuclear Information System (INIS)

Shankar Prasad Shrestha; Park, C.-Y.

2006-05-01

We have made a systematic study of influence of diffusion flux ratio (D/F), diffusional anisotropy (DA) and sticking anisotropy (SA) on island morphology to show the influence of each growth parameter on island morphology in presence of the other growth parameters. Our results show that the influence of D/F ratio and DA on island morphology depends on the sticking anisotropy of the adatoms. At the intermediate anisotropic case, increase in D/F ratio results in transition of the island morphology from 1d nature to 2 d nature. In anisotropic diffusion case, D/F ratio can change the growth direction of the island morphology. We also find that only sticking anisotropy is not sufficient to produce elongated islands, low D/F ratio is also essential. (author)

Influence of oral detergents and chlorhexidine on soft-layer electrokinetic parameters of the acquired enamel pellicle

NARCIS (Netherlands)

Busscher, HJ; White, DJ; Kamminga-Rasker, HJ; Poortinga, AT; van der Mei, HC

2003-01-01

Electron microscopy has described the salivary pellicle as an 'uneven, knotted structure'. This study describes a novel soft-layer model of salivary pellicles, based on measured electrophoretic mobilities and the influence of dentifrices and a chlorhexidine mouthwash on the parameters of the model.

Influence of several experimental parameters on As and Se leaching from coal fly ash samples

International Nuclear Information System (INIS)

Otero-Rey, Jose R.; Mato-Fernandez, Maria J.; Moreda-Pineiro, Jorge; Alonso-Rodriguez, Elia; Muniategui-Lorenzo, Soledad; Lopez-Mahia, Purificacion; Prada-Rodriguez, Dario

2005-01-01

Coal fly ash leaching process for As and Se is studied. Environmental parameters such as pH, temperature, solid-liquid ratio, particle size and leaching time are taken into account in order to simulate As and Se leaching process for disposal coal fly ash. Analysis of reference materials was carried out by using of hydride generation coupled to atomic fluorescence spectrometry. Plackett-Burman experimental design is used to know the significative parameters, and Box-Behnken experimental design is used to refine the results obtained for these significative parameters. pH and temperature shown a hardly influence in leaching process. Furthermore, leaching time was also significative. According our results, it may be assumed that percentage of As and Se leaching in experimental conditions tested is relatively low for acidic fly ashes

The influence of self-relevant materials on working memory in dysphoric undergraduates.

Science.gov (United States)

Dai, Qin; Rahman, Shaoon; Lau, Becky; Sook Kim, Hyang; Deldin, Patricia

2015-10-30

Difficulties in updating working memory (WM) may underlie problems with regulating emotions that contribute to depression. To examine the ability of updating affective materials in WM, 33 dysphoric and 34 non-dysphoric participants were asked to evaluate the self-descriptiveness of emotional adjectives and provide answers to self-relevant questions. Within 3-7 days, they completed a two-back task with a series of self-irrelevant or self-relevant emotional words (they had generated previously) and four conditions (match-set, break-set, perseveration-set, and no-set). After the WM task, an unexpected recall task was administered; controls recalled more positive self-relevant words and intrusions while dysphoric participants recalled more negative self-relevant words and intrusions. In break-set trials of the two-back task, dysphoric individuals showed slower response to self-relevant words regardless of valence. In the match-set and perseveration-set trials, dysphoric participants showed delayed response to self-related negative words. Moreover, longer reaction times for self-relevant negative words were correlated with higher rumination and worse depression. The results suggest that dysphoric undergraduates are interfered more by and have a better memory of self-relevant negative stimuli in WM, which is closely correlated with rumination. This study is among the first to confirm the potential mechanism that could underwrite the involvement of self-schema in effectively regulating negative affect. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

The study of influence of relevant physical parameters variations on the estimates of the effective doses of Rn-222

International Nuclear Information System (INIS)

Ridzikova, A.; Fronka, A.; Moucka, L.

2004-01-01

Based on the analysis of 12 weekly continuous measurements and 4 integral measurements performed in different seasons in actual apartment rooms, bedrooms in particular, we attempted to identify the uncertainties that are involved in the estimation of radiation doses to lung tissues. We found that the parameters of time of residence, concentration, and equilibrium factor can affect substantially the estimate of the overall early effective dose. The weekly averaged concentration measured in one term is not sufficient for a fairly accurate estimate; actually, the equilibrium factor f must also be known and the actual real individual time of residence must be estimated if we want to adopt this approach to the dose estimation

Influence of corneal parameters in keratoconus on IOP readings obtained with different tonometers.

Science.gov (United States)

Firat, Penpe Gul; Orman, Gozde; Doganay, Selim; Demirel, Soner

2013-03-01

Accurate intraocular pressure (IOP) measurement is important but of unsure reliability in patients with keratoconus. Different types and models of tonometers are available. This study investigated the influence of corneal parameters on IOP readings obtained by a Goldmann applanation tonometer, a non-contact tonometer and a dynamic contour tonometer. IOP readings with the Goldmann applanation, non-contact and dynamic contour tonometers were obtained from 52 patients with keratoconus and from 50 normal subjects and their corneal parameters were measured using a Pentacam. The mean IOP measurements in keratoconus obtained with the Goldmann applanation, non-contact and dynamic contour tonometers were statistically significantly different from the mean IOP measurements in the normal subjects (p contact tonometers but not on the dynamic contour tonometer. In the control group, thinnest and central corneal thicknesses had a significant effect on findings with the Goldmann and non-contact tonometers but not on the dynamic contour tonometer. The corneal volume (CV) had no significant effect on the three tonometers in both groups. The corneal parameters affecting the IOP readings of the Goldmann applanation tonometers, non-contact tonometers and the dynamic contour tonometers are not the same. While the Goldmann applanation and non-contact tonometers were significantly affected by the corneal parameters that were measured, the dynamic contour tonometer was not affected by any of these corneal parameters. © 2013 The Authors. Clinical and Experimental Optometry © 2013 Optometrists Association Australia.

Estimation of biological parameters of marine organisms using linear and nonlinear acoustic scattering model-based inversion methods.

Science.gov (United States)

Chu, Dezhang; Lawson, Gareth L; Wiebe, Peter H

2016-05-01

The linear inversion commonly used in fisheries and zooplankton acoustics assumes a constant inversion kernel and ignores the uncertainties associated with the shape and behavior of the scattering targets, as well as other relevant animal parameters. Here, errors of the linear inversion due to uncertainty associated with the inversion kernel are quantified. A scattering model-based nonlinear inversion method is presented that takes into account the nonlinearity of the inverse problem and is able to estimate simultaneously animal abundance and the parameters associated with the scattering model inherent to the kernel. It uses sophisticated scattering models to estimate first, the abundance, and second, the relevant shape and behavioral parameters of the target organisms. Numerical simulations demonstrate that the abundance, size, and behavior (tilt angle) parameters of marine animals (fish or zooplankton) can be accurately inferred from the inversion by using multi-frequency acoustic data. The influence of the singularity and uncertainty in the inversion kernel on the inversion results can be mitigated by examining the singular values for linear inverse problems and employing a non-linear inversion involving a scattering model-based kernel.

The influence of the anesthesia-to-stimulation time interval on seizure quality parameters in electroconvulsive therapy

DEFF Research Database (Denmark)

Jorgensen, A; Christensen, S J; Jensen, A E K

2018-01-01

BACKGROUND: Electroconvulsive therapy (ECT) continues to be the most efficacious treatment for severe depression and other life-threatening acute psychiatric conditions. Treatment efficacy is dependent upon the induced seizure quality, which may be influenced by a range of treatment related factors....... Recently, the time interval from anesthesia to the electrical stimulation (ASTI) has been suggested to be an important determinant of seizure quality. METHODS: We measured ASTI in 73 ECT sessions given to 22 individual patients, and analyzed its influence on five seizure quality parameters (EEG seizure...

Influence of the selected structural parameter on a depth of intergranular corrosion of Al-Si7-Mg0,3 aluminum alloy

Directory of Open Access Journals (Sweden)

L. Bernat

2015-10-01

Full Text Available The paper presents an influence of the Dendrite Arm Spacing (DAS microstructure parameter on the intergranular corrosion of AlSi7Mg aluminum alloy. The samples were subjected to the corrosion process for: 2,5; 12; 24; 48 and 96 hours in NaCl + HCl + H2O solution. It was noted that the DAS parameter significantly influenced on a distribution and depth of the intergranular corrosion of the hypoeutectic Al - Si - Mg silumin.

Mesh parameters influence on transparent and active antennas performance at microwaves

Directory of Open Access Journals (Sweden)

Alexis Martin

2017-08-01

Full Text Available Optically transparent and active square loop coplanar antennas operating in X-band are investigated in this letter. The frequency tunability is provided by a surface mounted beam-lead varactor with micrometric size, thereby no-visible to the naked eye. The influence of the metal mesh parameters on the sheet resistance (from 0.05 Ω/sq to 0.54 Ω/sq, the optical transparency (from 66% to 89% and the microwave performance (return loss, resonance frequency, radiation pattern and gain of such antennas is evaluated, compared with those of an opaque counterpart, and finally discussed. This study paves the way of their promising implementation on new surfaces, namely building and car windows for future wireless communications systems.

A numerical study of non-linear crack tip parameters

Directory of Open Access Journals (Sweden)

F.V. Antunes

2015-07-01

Full Text Available Crack closure concept has been widely used to explain different issues of fatigue crack propagation. However, different authors have questioned the relevance of crack closure and have proposed alternative concepts. The main objective here is to check the effectiveness of crack closure concept by linking the contact of crack flanks with non-linear crack tip parameters. Accordingly, 3D-FE numerical models with and without contact were developed for a wide range of loading scenarios and the crack tip parameters usually linked to fatigue crack growth, namely range of cyclic plastic strain, crack tip opening displacement, size of reversed plastic zone and total plastic dissipation per cycle, were investigated. It was demonstrated that: i LEFM concepts are applicable to the problem under study; ii the crack closure phenomenon has a great influence on crack tip parameters decreasing their values; iii the Keff concept is able to explain the variations of crack tip parameters produced by the contact of crack flanks; iv the analysis of remote compliance is the best numerical parameter to quantify the crack opening level; v without contact there is no effect of stress ratio on crack tip parameters. Therefore it is proved that the crack closure concept is valid.

Estimation of the Influence of Power System Mathematical Model Parameter Uncertainty on PSS2A System Stabilizers

Directory of Open Access Journals (Sweden)

Adrian Nocoń

2015-09-01

Full Text Available This paper presents an analysis of the influence of uncertainty of power system mathematical model parameters on optimised parameters of PSS2A system stabilizers. Optimisation of power system stabilizer parameters was based on polyoptimisation (multi-criteria optimisation. Optimisation criteria were determined for disturbances occurring in a multi-machine power system, when taking into account transient waveforms associated with electromechanical swings (instantaneous power, angular speed and terminal voltage waveforms of generators. A genetic algorithm with floating-point encoding, tournament selection, mean crossover and perturbative mutations, modified for the needs of investigations, was used for optimisation. The impact of uncertainties on the quality of operation of power system stabilizers with optimised parameters has been evaluated using various deformation factors.

Influence of the section size and holding time on the graphite parameters of ductile iron production

Directory of Open Access Journals (Sweden)

S. Bockus

2009-01-01

Full Text Available This work was conducted to establish the conditions required to produce a desirable structure of the castings of various section sizes. This investigation was focused on the study of the influence of cooling rate or section size and holding time on graphite parameters of the ductile iron. Plates having thickness between 3 and 50mm were cast in sand molds using the same melt. The present investigation has shown that the section size of ductile iron castings and holding time had strong effect on the graphite parameters of the castings.

Experimental investigation of urea injection parameters influence on NOx emissions from blended biodiesel-fueled diesel engines.

Science.gov (United States)

Mehregan, Mina; Moghiman, Mohammad

2018-02-01

The present work submits an investigation about the effect of urea injection parameters on NO x emissions from a four-stroke four-cylinder diesel engine fueled with B20 blended biodiesel. An L 9 (3 4 ) Taguchi orthogonal array was used to design the test plan. The results reveal that increasing urea concentration leads to lower NO x emissions. Urea flow rate increment has the same influence on NO x emission. The same result is obtained by an increase in spray angle. Also, according to the analysis of variance (ANOVA), urea concentration and then urea flow rate are the most effective design parameters on NO x emissions, while spray angle and mixing length have less influence on this pollutant emission. Finally, since the result of confirmation test is in good agreement with the predicted value based on the Taguchi technique, the predictive capability of this method in the present study could be deduced.

Influences of some parameters on the performance of a small vertical axis wind turbine

Directory of Open Access Journals (Sweden)

Dumitrache Alexandru

2016-01-01

Full Text Available The effects of various parameters on the performance of a straight bladed vertical axis wind turbine, using the vortex model, have been numerically investigated. A vortex model has been used to evaluate the performance of a vertical axis wind turbine, by means of aerodynamic characteristics of different airfoils for Reynolds numbers between 105 and 106. Parameters such as the thickness and the camber of the blade airfoil, the solidity, the type of blade profile, the number of blades and the pitch angle, which influence the power coefficient, CP, and the start-up regime. This study can be used in the designing an optimal vertical axis wind turbine in a specific location, when the prevailed wind regime is known.

Prestimulus influences on auditory perception from sensory representations and decision processes.

Science.gov (United States)

Kayser, Stephanie J; McNair, Steven W; Kayser, Christoph

2016-04-26

The qualities of perception depend not only on the sensory inputs but also on the brain state before stimulus presentation. Although the collective evidence from neuroimaging studies for a relation between prestimulus state and perception is strong, the interpretation in the context of sensory computations or decision processes has remained difficult. In the auditory system, for example, previous studies have reported a wide range of effects in terms of the perceptually relevant frequency bands and state parameters (phase/power). To dissociate influences of state on earlier sensory representations and higher-level decision processes, we collected behavioral and EEG data in human participants performing two auditory discrimination tasks relying on distinct acoustic features. Using single-trial decoding, we quantified the relation between prestimulus activity, relevant sensory evidence, and choice in different task-relevant EEG components. Within auditory networks, we found that phase had no direct influence on choice, whereas power in task-specific frequency bands affected the encoding of sensory evidence. Within later-activated frontoparietal regions, theta and alpha phase had a direct influence on choice, without involving sensory evidence. These results delineate two consistent mechanisms by which prestimulus activity shapes perception. However, the timescales of the relevant neural activity depend on the specific brain regions engaged by the respective task.

Perceived Relevance of an Introductory Information Systems Course to Prospective Business Students

Directory of Open Access Journals (Sweden)

Irene Govender

2013-12-01

Full Text Available The study is designed to examine students’ perceptions of the introductory Information Systems (IS course. It was an exploratory study in which 67 students participated. A quantitative approach was followed making use of questionnaires for the collection of data. Using the theory of reasoned action as a framework, the study explores the factors that influence non-IS major students’ perceived relevance of the IS introductory course. The analysis of collected data included descriptive and inferential statistics. Using multiple regression analysis, the results suggest that overall, the independent variables, relevance of the content, previous IT knowledge, relevance for professional practice, IT preference in courses and peers’ influence may account for 72% of the explanatory power for the dependent variable, perceived relevance of the IS course. In addition, the results have shown some strong predictors (IT preference and peers’ influence that influence students’ perceived relevance of the IS course. Practical work was found to be a strong mediating variable toward positive perceptions of IS. The results of this study suggest that students do indeed perceive the introductory IS course to be relevant and match their professional needs, but more practical work would enhance their learning. Implications for theory and practice are discussed as a result of the behavioural intention to perceive the IS course to be relevant and eventually to recruit more IS students.

Investigation of the Influence of Hydrocyclone Geometric and Flow Parameters on Its Performance Using CFD

Directory of Open Access Journals (Sweden)

Oboetswe Seraga Motsamai

2010-01-01

Full Text Available Effectiveness and efficiency of hydro-cyclone separators are highly dependent on their geometrical parameters and flow characteristics. Performance of the hydro-cyclone can, therefore, be improved by modifying the geometrical parameters or flow characteristics. The mining and chemical industries are faced with problems of separating ore-rich stones from the nonore-rich stones. Due to this problem a certain amount of precious metals is lost to the dumping sites. Plant managers try to solve these problems by stockpiling what could be useless stones, so that they can be reprocessed in the future. Reprocessing is not a sustainable approach, because the reprocessed material would give lower yield as compared to the production costs. Particulate separation in a hydro-cyclone has been investigated in this paper, by using computational fluid dynamics. The paper investigated the influence of various flow and geometric parameters on particulate separation. Optimal parameters for efficient separation have been determined for the density of fluid, diameter of the spigot, and diameter of the vortex finder. The principal contribution of this paper is that key parameters for design optimization of the hydro-cyclone have been investigated.

Analysis of Network Parameters Influencing Performance of Hybrid Multimedia Networks

Directory of Open Access Journals (Sweden)

Dominik Kovac

2013-10-01

Full Text Available Multimedia networks is an emerging subject that currently attracts the attention of research and industrial communities. This environment provides new entertainment services and business opportunities merged with all well-known network services like VoIP calls or file transfers. Such a heterogeneous system has to be able satisfy all network and end-user requirements which are increasing constantly. Therefore the simulation tools enabling deep analysis in order to find the key performance indicators and factors which influence the overall quality for specific network service the most are highly needed. This paper provides a study on the network parameters like communication technology, routing protocol, QoS mechanism, etc. and their effect on the performance of hybrid multimedia network. The analysis was performed in OPNET Modeler environment and the most interesting results are discussed at the end of this paper

Evaluating automatic attentional capture by self-relevant information.

Science.gov (United States)

Ocampo, Brenda; Kahan, Todd A

2016-01-01

Our everyday decisions and memories are inadvertently influenced by self-relevant information. For example, we are faster and more accurate at making perceptual judgments about stimuli associated with ourselves, such as our own face or name, as compared with familiar non-self-relevant stimuli. Humphreys and Sui propose a "self-attention network" to account for these effects, wherein self-relevant stimuli automatically capture our attention and subsequently enhance the perceptual processing of self-relevant information. We propose that the masked priming paradigm and continuous flash suppression represent two ways to experimentally examine these controversial claims.

Technological parameter and experimental set-up influences on latch-up triggering level in bulk CMOS device

International Nuclear Information System (INIS)

Dubuc, J.P.; Azais, B.; Murcia, M. de

1994-01-01

This paper deals with experimental and simulation results on latch-up triggered by an electrical or X-rays pulse in CMOS/bulk devices. Test condition influences as well as the great importance of process parameters on latch-up immunity are emphasized. (author). 10 refs., 19 figs., 1 tab

The Influence of Hydrologic Parameters on the Hydraulic Efficiency of an Extensive Green Roof in Mediterranean Area

Directory of Open Access Journals (Sweden)

Giuseppina Garofalo

2016-01-01

Full Text Available In an urban environment, green roofs represent a sustainable solution for mitigating stormwater volumes and hydrograph peaks. So far, many literature studies have investigated the hydraulic efficiency and the subsurface runoff coefficient of green roofs, showing their strong variability according to several factors, including the characteristics of storm events. Furthermore, only few studies have focused on the hydraulic efficiency of green roofs under Mediterranean climate conditions and defined the influencing hydrological parameters on the subsurface runoff coefficient. Nevertheless, for designing purposes, it is crucial to properly assess the subsurface runoff coefficient of a given green roof under specific climate conditions and its influencing factors. This study intends to, firstly, evaluate the subsurface runoff coefficient at daily and event-time scales for a given green roof, through a conceptual model implemented in SWMM. The model was loaded with both daily and 1-min rainfall data from two Mediterranean climate sites, one in Thessaloniki, Greece and one in Cosenza, Italy, respectively. Then, the most influencing hydrological parameters were examined through a statistical regression analysis. The findings show that the daily subsurface runoff coefficient is 0.70 for both sites, while the event-based one is 0.79 with a standard deviation of 0.23 for the site in Cosenza, Italy. The multiple linear regression analysis revealed that the influencing parameters are the rainfall intensity and antecedent dry weather period with a confidence level of 95%. This study demonstrated that, due to the high variability of the subsurface runoff coefficient, the use of a unique value for design purposes is inappropriate and that a preliminary estimation could be obtained as a function of the total rainfall depth and the antecedent dry weather period by using the validated multi-regression relationship which is site specific.

Influence analysis of structural parameters on electromagnetic properties of HTS linear induction motor

International Nuclear Information System (INIS)

Zhao, J.; Zheng, T.Q.; Zhang, W.; Fang, J.; Liu, Y.M.

2011-01-01

A new type high temperature superconductor linear induction motor is designed and analyzed as a prototype to ensure applicability aimed at industrial motors. Made of Bi-2223/Ag, primary windings are distributed with the double-layer concentrated structure. The motor is analyzed by 2D electromagnetic Finite Element Method to get magnetic field distribution, thrust force, vertical force and so on. The critical current of motor and the electromagnetic force are mostly decided by the leakage flux density of primary slot and by the main magnetic flux and eddy current respectively. The structural parameters of motor have a great influence on the distribution of magnetic field. Under constant currents, the properties of motor are analyzed with different slot widths, slot heights and winding turns. The properties of motor, such as the maximum slot leakage flux density, motor thrust and motor vertical force, are analyzed with different structural parameters.

The influence of maternal smoking on transferrin sialylation and fetal biometric parameters.

Science.gov (United States)

Wrześniak, Marta; Królik, Małgorzata; Kepinska, Marta; Milnerowicz, Halina

2016-10-01

Transferrin is a glycosylated protein responsible for transporting iron, an essential metal responsible for proper fetal development. Tobacco is a heavily used xenobiotic having a negative impact on the human body and pregnancy outcomes. Aims of this study was to examine the influence of tobacco smoking on transferrin sialic acid residues and their connection with fetal biometric parameters in women with iron-deficiency. The study involved 173 samples from pregnant women, smokers and non-smokers, iron deficient and not. Transferrin sialylation was determined by capillary electrophoresis. The cadmium (Cd) level was measured by atomic absorption and the sialic acid concentration by the resorcinol method. Women with iron deficiencies who smoked gave birth earlier than non-smoking, non-iron-deficient women. The Cd level, but not the cotinine level, was positively correlated with transferrin sialylation in the blood of iron-deficient women who smoked; 3-, 4-, 5- and 6-sialoTf correlated negatively with fetal biometric parameters in the same group. It has been shown the relationship between Cd from tobacco smoking and fetal biometric parameters observed only in the iron deficient group suggests an additive effect of these two factors, and indicate that mothers with anemia may be more susceptible to Cd toxicity and disturbed fetal development. Copyright © 2016 Elsevier B.V. All rights reserved.

Application effect of hyperbaric oxygen in the patients with optic atrophy and influence for the hemodynamic parameters

Directory of Open Access Journals (Sweden)

Kun Zhang

2015-01-01

Full Text Available AIM: To observe the application effect of hyperbaric oxygen in the patients with optic atrophy and influence degree for the hemodynamic parameters.METHODS: Fifty patients with optic atrophy in our hospital from January 2012 to January 2014 were objected, they were randomly divided into control group(conventional optic atrophy treatment groupand observation group(conventional treatment and hyperbaric oxygen treatment group, each group was 25 cases. Statistical analysis of two group before and after treatment eyesight, vision acuity, visual field defect and ophthalmic artery, central retinal artery blood flow parameters were undergone.RESULTS: The sight, visual field sensitivity and field vision defect of observation group were all better than those of control group at first, second and third course after the treatment, arteriae ophthalmica and arteriae centralis retinae EDV and PSV were all higher than those of control group, PI and RI were all lower than those of control group were all significant differences(PCONCLUSION: The application effect of hyperbaric oxygen in the patients with optic atrophy is better, and the influence of treatment method for the ocular hemodynamic parameters are more active.

Influence patterns of transportation parameters in suburban traffic on fatigue of passengers during bus waiting

Directory of Open Access Journals (Sweden)

Тетяна Михайлівна Григорова

2015-05-01

Full Text Available The change of transport fatigue of suburban traffic passengers during waiting transport waiting is investigated. The results of the processing site examinations allow defining the regularities of the influence of parameters of transportation process of passengers to change index activity of regulatory systems in passenger waiting at stopping points of suburban traffic. The discovered patterns were mathematically formalized

Evaluation of cyclone geometry and its influence on performance parameters by computational fluid dynamics (CFD

Directory of Open Access Journals (Sweden)

W. P. Martignoni

2007-03-01

Full Text Available Cyclone models have been used without relevant modifications for more than a century. Most of the attention has been focused on finding new methods to improve performance parameters. Recently, some studies were conducted to improve equipment performance by evaluating geometric effects on projects. In this work, the effect of cyclone geometry was studied through the creation of a symmetrical inlet and a volute scroll outlet section in an experimental cyclone and comparison to an ordinary single tangential inlet. The study was performed for gas-solid flow, based on an experimental study available in the literature, where a conventional cyclone model was used. Numerical experiments were performed by using CFX 5.7.1. The axial and tangential velocity components were evaluated using RSM and LES turbulence models. Results showed that these new designs can improve the cyclone performance parameters significantly and very interesting details were found on cyclone fluid dynamics properties using RSM and LES.

Inventory parameters

CERN Document Server

Sharma, Sanjay

2017-01-01

This book provides a detailed overview of various parameters/factors involved in inventory analysis. It especially focuses on the assessment and modeling of basic inventory parameters, namely demand, procurement cost, cycle time, ordering cost, inventory carrying cost, inventory stock, stock out level, and stock out cost. In the context of economic lot size, it provides equations related to the optimum values. It also discusses why the optimum lot size and optimum total relevant cost are considered to be key decision variables, and uses numerous examples to explain each of these inventory parameters separately. Lastly, it provides detailed information on parameter estimation for different sectors/products. Written in a simple and lucid style, it offers a valuable resource for a broad readership, especially Master of Business Administration (MBA) students.

Influence of various manufacturing parameters on some characteristics of UO2 powders and their sintering behaviour

International Nuclear Information System (INIS)

Mintz, M.H.; Vaknin, Sh.; Kremener, A.; Hadari, Z.

1977-02-01

Various parameters in the process of manufacturing uranium dioxide are examined and their influence on the characteristics and sintering behaviour of the powders obtained established. In addition some correlations between the powder aggregates microstructure and their adhesion properties and sintering behaviour are indicated. Shrinkage during the sintering process is also discussed

Challenges while Updating Planning Parameters of an ERP System and How a Simulation-Based Support System Can Support Material Planners

Directory of Open Access Journals (Sweden)

Ulrike Stumvoll

2016-01-01

Full Text Available In an Enterprise Resource Planning (ERP system, production planning is influenced by a variety of parameters. Previous investigations show that setting parameter values is highly relevant to a company’s target system. Parameter settings should be checked and adjusted, e.g., after a change in environmental factors, by material planners. In practice, updating the parameters is difficult due to several reasons. This paper presents a simulation-based decision support system, which helps material planners in all stages of decision-making processes. It will present the system prototype’s user interface and the results of applying the system to a case study.

Influence of characteristics of time series on short-term forecasting error parameter changes in real time

Science.gov (United States)

Klevtsov, S. I.

2018-05-01

The impact of physical factors, such as temperature and others, leads to a change in the parameters of the technical object. Monitoring the change of parameters is necessary to prevent a dangerous situation. The control is carried out in real time. To predict the change in the parameter, a time series is used in this paper. Forecasting allows one to determine the possibility of a dangerous change in a parameter before the moment when this change occurs. The control system in this case has more time to prevent a dangerous situation. A simple time series was chosen. In this case, the algorithm is simple. The algorithm is executed in the microprocessor module in the background. The efficiency of using the time series is affected by its characteristics, which must be adjusted. In the work, the influence of these characteristics on the error of prediction of the controlled parameter was studied. This takes into account the behavior of the parameter. The values of the forecast lag are determined. The results of the research, in the case of their use, will improve the efficiency of monitoring the technical object during its operation.

[The influence of cryochamber on parameters of blood pressure and pulse].

Science.gov (United States)

Szczepanowska-Wołowiec, Beata; Dudek, Jolanta; Wołowiec, Paulina; Kotela, Ireneusz

2010-01-01

The influence of whole body cryotherapy on human body. The study was conducted on a group of 50 patients of the Rehabilitation Ward in Wojewodzki Szpital Zespolony in Kielce suffering from chronic pain as a sequel of degenerative-deformative changes and residing. Physiotherapy consisted of treatments in cryo-chamber and physical exercises. The average heart rate in the study group before the treatment amounted to 66.5 beats/min +/- 5.7 after the courses of treatments it constituted to 63.1 beats/min. +/- 3.6 at the significance level p whole body cryotherapy and 10 courses of those combined with physical exercises caused statistically significant reduction in the heart rate and pressure parameters. The downward trend was observed in all courses of treatments conducted in this study.

Location Criteria Relevant for Sustainability of Social Housing Model

Directory of Open Access Journals (Sweden)

Petković-Grozdanović Nataša

2016-01-01

Full Text Available Social housing models, which had began to develop during the last century, for their only objective had a need to overcome the housing problems of socially vulnerable categories. However, numerous studies have shown that these social categories, because of their low social status, are highly susceptible to various psychological and sociological problems. On the other hand a low level of quality, which was common for social housing dwellings, has further aggravated these problems by initiating trouble behaviours among tenants, affecting social exclusion and segregation. Contemporary social housing models are therefore conceptualized in a way to provide a positive psycho-sociological impact on their tenants. Therefore the planning approach in social housing should be such to: support important functions in daily life routines; promote tolerance and cooperation; influence on a sense of social order and belonging; affect the socialization of the tenant and their integration into the wider community; and improve social cohesion. Analysis of the influential location parameters of immediate and wider social housing environment strive to define the ones relevant to the life quality of social housing tenants and therefore influence on the sustainability of social housing model.

Influence of processing parameters on PZT thick films

International Nuclear Information System (INIS)

Huang, Oliver; Bandyopadhyay, Amit; Bose, Susmita

2005-01-01

We have studied influence of processing parameters on the microstructure and ferroelectric properties of lead zirconate titanate (PZT)-based thick films in the range of 5-25 μm. PZT and 2% La-doped PZT thick films were processed using a modified sol-gel process. In this process, PZT- and La-doped PZT powders were first prepared via sol-gel. These powders were calcined and then used with respective sols to form a slurry. Slurry composition was optimized to spin-coat thick films on platinized Si substrate (Si/SiO 2 /Ti/Pt). Spinning rate, acceleration and slurry deposition techniques were optimized to form thick films with uniform thickness and without any cracking. Increasing solids loading was found to enhance the surface smoothness of the film and decrease porosity. Films were tested for their electrical properties and ferroelectric fatigue response. The maximum polarization obtained was 40 μC/cm 2 at 250 kV/cm for PZT thick film and 30 μC/cm 2 at 450 kV/cm for La-doped PZT thick film. After 10 9 cycles of fatiguing at 35 kHz, La-doped PZT showed better resistance for ferroelectric fatigue compared with un-doped PZT films

Role of calibration, validation, and relevance in multi-level uncertainty integration

International Nuclear Information System (INIS)

Li, Chenzhao; Mahadevan, Sankaran

2016-01-01

Calibration of model parameters is an essential step in predicting the response of a complicated system, but the lack of data at the system level makes it impossible to conduct this quantification directly. In such a situation, system model parameters are estimated using tests at lower levels of complexity which share the same model parameters with the system. For such a multi-level problem, this paper proposes a methodology to quantify the uncertainty in the system level prediction by integrating calibration, validation and sensitivity analysis at different levels. The proposed approach considers the validity of the models used for parameter estimation at lower levels, as well as the relevance at the lower level to the prediction at the system level. The model validity is evaluated using a model reliability metric, and models with multivariate output are considered. The relevance is quantified by comparing Sobol indices at the lower level and system level, thus measuring the extent to which a lower level test represents the characteristics of the system so that the calibration results can be reliably used in the system level. Finally the results of calibration, validation and relevance analysis are integrated in a roll-up method to predict the system output. - Highlights: • Relevance analysis to quantify the closeness of two models. • Stochastic model reliability metric to integrate multiple validation experiments. • Extend the model reliability metric to deal with multivariate output. • Roll-up formula to integrate calibration, validation, and relevance.

Influence of Music on Preoperative Anxiety and Physiologic Parameters in Women Undergoing Gynecologic Surgery.

Science.gov (United States)

Labrague, Leodoro J; McEnroe-Petitte, Denise M

2016-04-01

The aim of this study was to determine the influence of music on anxiety levels and physiologic parameters in women undergoing gynecologic surgery. This study employed a pre- and posttest experimental design with nonrandom assignment. Ninety-seven women undergoing gynecologic surgery were included in the study, where 49 were allocated to the control group (nonmusic group) and 48 were assigned to the experimental group (music group). Preoperative anxiety was measured using the State Trait Anxiety Inventory (STAI) while noninvasive instruments were used in measuring the patients' physiologic parameters (blood pressure [BP], pulse [P], and respiration [R]) at two time periods. Women allocated in the experimental group had lower STAI scores (t = 17.41, p music during the preoperative period in reducing anxiety and unpleasant symptoms in women undergoing gynecologic surgery. © The Author(s) 2014.

The influence of optical parameters on impurity determinations by IR spectroscopy

International Nuclear Information System (INIS)

Lombard, O.J.

1985-01-01

The important role of impurities in semiconductor materials is the subject of continuous research. The concentration of interstitial oxygen impurities in silicon are determined with the aid of infrared spectroscopy. The maximum absorption coefficient of the oxygen absorption peak, centered at 9,06 μm, is determined and the impurity concentration is then calculated using a calibration factor. This procedure was evaluated, paying particular attention to those optical parameters which may influence these impurity determinations. A thorough discussion of the theoretical and experimental aspects of infrared spectroscopy in general is followed by an overview of previous experimental work. This lead to some theoretical analysis regarding the influence of the index of refraction, the index of absorption and multiple reflections in the silicon wafer on impurity determinations. This lead to specific experimental investigations. The influence of the surface morphology of samples on impurity determinations was studied by determining the reflectance of silicon surfaces. It was established that the surface reflectance plays a role and that it must be taken into consideration for accurate impurity concentration determinations. The most accurate values for the absorption coefficient due to oxygen in silicon are calculated. This requires that the surface of the silicon wafers must be highly polished for the formula to be valid. Acceptable values for the absorption coefficient of damaged surfaces are obtained if the uncorrected formula is used. Experimental results may deviate as much as 32% from the real impurity concentration if the wrong formula is used to calculate the absorption coefficient of oxygen in silicon at 9,06 μm

Changes of the more relevant PHTS parameters after the cleaning of the steam generators primary side at Embalse nuclear power plant

International Nuclear Information System (INIS)

Moreno, Carlos A.; Coutsiers, Ernesto; Acevedo, Paul; Pomerantz, Marcelo E.

2003-01-01

During the operation of the plant magnetite deposition occurs at the inner walls of Primary Heat Transport System (PHTS). This deposition is particularly significant at the U-tubes of steam generators. The consequence of this is the deterioration of heat transfer to the Secondary System. In order to minimize this impact, during the annual outage of 2000, the steam generators primary side cleaning by the SIVABLAST technique was carried out. This technique consists in blasting the inner walls with tiny stainless steel balls propelled by air at high pressure. This paper presents the change of the more relevant parameters of PHTS after that cleaning. The parameters analyzed and the main results are the following: 1) Inlet header temperature dropped 4.7 C degrees at full power; 2) Exit quality at the outlet headers decreased from 3,5% to 1,5%; 3) Global PHTS flow in single phase evaluated from: a) In-site instrumentation increased 4,6%; b) Thermalhydraulic code NUCIRC 1.0 increased 3,2%; c) measured flows at the instrumented fuel channels increased 4.4%. (author)

Influence of extrusion-cooking parameters on some quality aspects of precooked pasta-like products.

Science.gov (United States)

Wójtowicz, A; Mościcki, L

2009-06-01

The present article aims to evaluate some quality parameters and texture characteristics of precooked wheat pasta-like products. Using the methods for pasta and instant noodles the tested parameters were water absorption, starch gelatinization degree, cooking losses, and hardness. The texture profile was characterized using Zwick apparatus by cutting test with the head speed of 10 mm/min and expressed as hardness and firmness of hydrated products. SEM pictures were used to illustrate the internal structure of dry and cooked pasta-like products. Dough moisture content and process conditions influenced all tested quality parameters of the pasta-like products processed on a modified single screw extrusion-cooker TS-45 with L: D = 16: 1. Good organoleptical quality (notes higher than 4 in a 5-point scale) and firm texture were observed for common wheat flour pasta processed at 30% m.c. Hardness and firmness of hydrated products lowered with a longer hydration time in hot water. The firmest texture and low stickiness was observed for products with a highest starch gelatinization degree.

Influence of source parameters on the growth of metal nanoparticles by sputter-gas-aggregation

Science.gov (United States)

Khojasteh, Malak; Kresin, Vitaly V.

2017-11-01

We describe the production of size-selected manganese nanoclusters using a magnetron sputtering/aggregation source. Since nanoparticle production is sensitive to a range of overlapping operating parameters (in particular, the sputtering discharge power, the inert gas flow rates, and the aggregation length), we focus on a detailed map of the influence of each parameter on the average nanocluster size. In this way, it is possible to identify the main contribution of each parameter to the physical processes taking place within the source. The discharge power and argon flow supply the metal vapor, and argon also plays a crucial role in the formation of condensation nuclei via three-body collisions. However, the argon flow and the discharge power have a relatively weak effect on the average nanocluster size in the exiting beam. Here the defining role is played by the source residence time, governed by the helium supply (which raises the pressure and density of the gas column inside the source, resulting in more efficient transport of nanoparticles to the exit) and by the aggregation path length.

Influence of processing parameters on lattice parameters in laser deposited tool alloy steel

Energy Technology Data Exchange (ETDEWEB)

Sun, G.F., E-mail: gfsun82@gmail.com [Center for Laser-Aided Intelligent Manufacturing, University of Michigan, Ann Arbor, MI, 48109 (United States); School of Mechanical Engineering, Jiangsu University, Zhenjiang, Jiangsu, 212013 (China); Bhattacharya, S. [Center for Laser-Aided Intelligent Manufacturing, University of Michigan, Ann Arbor, MI, 48109 (United States); Dinda, G.P.; Dasgupta, A. [Center for Advanced Technologies, Focus: Hope, Detroit, MI, 48238 (United States); Mazumder, J. [Center for Laser-Aided Intelligent Manufacturing, University of Michigan, Ann Arbor, MI, 48109 (United States)

2011-06-15

Highlights: {yields} Orientation relationships among phases in the DMD are given. {yields} Martensite lattice parameters increased with laser specific energy. {yields} Austenite lattice parameters decreased with laser specific energy. - Abstract: Laser aided direct metal deposition (DMD) has been used to form AISI 4340 steel coating on the AISI 4140 steel substrate. The microstructural property of the DMD coating was analyzed by means of scanning electron microscopy, transmission electron microscopy and X-ray diffractometry. Microhardness of the DMD was measured with a Vickers microhardness tester. Results indicate that DMD can be used to form dense AISI 4340 steel coatings on AISI 4140 steel substrate. The DMD coating is mainly composed of martensite and retained austenite. Consecutive thermal cycles have a remarkable effect on the microstructure of the plan view of the DMD coating and on the corresponding microhardness distribution. Orientation relationships among austenite, martensite and cementite in the DMD coating followed the ones in conventional heat treated steels. As the laser specific energy decreased, cooling rate increased, and martensite peaks broadened and shifted to a lower Bragg's angle. Also martensite lattice parameters increased and austenite lattice parameters decreased due to the above parameter change.

Influence of processing parameters on lattice parameters in laser deposited tool alloy steel

International Nuclear Information System (INIS)

Sun, G.F.; Bhattacharya, S.; Dinda, G.P.; Dasgupta, A.; Mazumder, J.

2011-01-01

Highlights: → Orientation relationships among phases in the DMD are given. → Martensite lattice parameters increased with laser specific energy. → Austenite lattice parameters decreased with laser specific energy. - Abstract: Laser aided direct metal deposition (DMD) has been used to form AISI 4340 steel coating on the AISI 4140 steel substrate. The microstructural property of the DMD coating was analyzed by means of scanning electron microscopy, transmission electron microscopy and X-ray diffractometry. Microhardness of the DMD was measured with a Vickers microhardness tester. Results indicate that DMD can be used to form dense AISI 4340 steel coatings on AISI 4140 steel substrate. The DMD coating is mainly composed of martensite and retained austenite. Consecutive thermal cycles have a remarkable effect on the microstructure of the plan view of the DMD coating and on the corresponding microhardness distribution. Orientation relationships among austenite, martensite and cementite in the DMD coating followed the ones in conventional heat treated steels. As the laser specific energy decreased, cooling rate increased, and martensite peaks broadened and shifted to a lower Bragg's angle. Also martensite lattice parameters increased and austenite lattice parameters decreased due to the above parameter change.

Discussion on the Influence of Various Technological Parameters on Jet Grouting Columns Geometry

Directory of Open Access Journals (Sweden)

Bzówka Joanna

2015-06-01

Full Text Available One of the most popular elements created by using jet grouting technology are columns. During designing such columns, it is a problem of estimating their shape and dimensions. The main factors that influence on columns geometry are soil characteristic and technological parameters. At the frame of Authors scientific research, following technological factors were taken into account: system of jet grouting, injection pressure, dimension of nozzles and rotation speed during injection. In the paper some results of the field tests of jet grouting columns are presented

[Photosynthetic parameters and physiological indexes of Paris polyphylla var. yunnanensis influenced by arbuscular mycorrhizal fungi].

Science.gov (United States)

Wei, Zheng-xin; Guo, Dong-qin; Li, Hai-feng; Ding, Bo; Zhang, Jie; Zhou, Nong; Yu, Jie

2015-10-01

Through potted inoculation test at room temperature and indoor analysis, the photosynthetic parameters and physiological and biochemical indexes of Paris polyphylla var. yunnanensis were observed after 28 arbuscular mycorrhizal (AM) fungi were injected into the P. polyphylla var. yunnanensis growing in a sterile soil environment. The results showed that AM fungi established a good symbiosis with P. polyphylla var. yunnanensis. The AM fungi influenced the photosynthetic parameters and physiological and biochemical indexes of P. polyphylla var. yunnanensis. And the influences were varied depending on different AM fungi. The application of AM fungi improved photosynthesis intensity of P. polyphylla var. yunnanensis mesophyll cells, the contents of soluble protein and soluble sugar, protective enzyme activity of P. polyphylla var. yunnanensis leaf, which was beneficial to resist the adverse environment and promote the growth of P. polyphylla var. yunnanensis. Otherwise, there was a certain mutual selectivity between P. polyphylla var. yunnanensis and AM fungi. From the comprehensive effect of inoculation, Racocetra coralloidea, Scutellospora calospora, Claroideoglomus claroideum, S. pellucida and Rhizophagus clarus were the most suitable AM fungi to P. polyphylla var. yunnanensis when P. polyphylla var. yunnanensis was planted in the field.

Convergent Cross Mapping: Basic concept, influence of estimation parameters and practical application.

Science.gov (United States)

Schiecke, Karin; Pester, Britta; Feucht, Martha; Leistritz, Lutz; Witte, Herbert

2015-01-01

In neuroscience, data are typically generated from neural network activity. Complex interactions between measured time series are involved, and nothing or only little is known about the underlying dynamic system. Convergent Cross Mapping (CCM) provides the possibility to investigate nonlinear causal interactions between time series by using nonlinear state space reconstruction. Aim of this study is to investigate the general applicability, and to show potentials and limitation of CCM. Influence of estimation parameters could be demonstrated by means of simulated data, whereas interval-based application of CCM on real data could be adapted for the investigation of interactions between heart rate and specific EEG components of children with temporal lobe epilepsy.

Influence of Processing Parameters on the Flow Path in Friction Stir Welding

Science.gov (United States)

Schneider, J. A.; Nunes, A. C., Jr.

2006-01-01

Friction stir welding (FSW) is a solid phase welding process that unites thermal and mechanical aspects to produce a high quality joint. The process variables are rpm, translational weld speed, and downward plunge force. The strain-temperature history of a metal element at each point on the cross-section of the weld is determined by the individual flow path taken by the particular filament of metal flowing around the tool as influenced by the process variables. The resulting properties of the weld are determined by the strain-temperature history. Thus to control FSW properties, improved understanding of the processing parameters on the metal flow path is necessary.

Objective parameters for engine noise quality evaluation; Objektive Parameter zur Bewertung der Motorgeraeuschqualitaet

Energy Technology Data Exchange (ETDEWEB)

Graf, Bernhard; Brandl, Stephan [AVL List GmbH, Graz (Austria); Sontacchi, Alois [Univ. fuer Musik und Darstellende Kunst, Graz (Austria). Inst. fuer Elektronische Musik und Akustik; Girstmair, Josef [Kompetenzzentrum Das Virtuelle Fahrzeug, Graz (Austria). Gruppe Antriebsstrang Dynamik und Akustik

2013-06-01

Due to ongoing downsizing efforts and more stringent emission regulations, relevance of sound quality monitoring during engine and vehicle development is strongly increasing. Therefore AVL developed new sound quality parameters like CKI (Combustion Knocking Index) and HI (Harshness Index). Using these parameters sound quality can be objectively monitored, without subjective evaluations, online throughout the complete development process. (orig.)

Influence of Parameters of Core Bingham Material on Critical Behaviour of Three-Layered Annular Plate

Directory of Open Access Journals (Sweden)

Pawlus Dorota

2017-12-01

Full Text Available The paper presents the dynamic response of annular three-layered plate subjected to loads variable in time. The plate is loaded in the plane of outer layers. The plate core has the electrorheological properties expressed by the Bingham body model. The dynamic stability loss of plate with elastic core is determined by the critical state parameters, particularly by the critical stresses. Numerous numerical observations show the influence of the values of viscosity constant and critical shear stresses, being the Bingham body parameters, on the supercritical viscous fluid plate behaviour. The problem has been solved analytically and numerically using the orthogonalization method and finite difference method. The solution includes both axisymmetric and asymmetric plate dynamic modes.

Influence of the "surface effect" on the segregation parameters of S in Fe(100): A multi-scale modelling and Auger Electron Spectroscopy study

Science.gov (United States)

Barnard, P. E.; Terblans, J. J.; Swart, H. C.

2015-12-01

The article takes a new look at the process of atomic segregation by considering the influence of surface relaxation on the segregation parameters; the activation energy (Q), segregation energy (ΔG), interaction parameter (Ω) and the pre-exponential factor (D0). Computational modelling, namely Density Functional Theory (DFT) and the Modified Darken Model (MDM) in conjunction with Auger Electron Spectroscopy (AES) was utilized to study the variation of the segregation parameters for S in the surface region of Fe(100). Results indicate a variation in each of the segregation parameters as a function of the atomic layer under consideration. Values of the segregation parameters varied more dramatically as the surface layer is approached, with atomic layer 2 having the largest deviations in comparison to the bulk values. This atomic layer had the highest Q value and formed the rate limiting step for the segregation of S towards the Fe(100) surface. It was found that the segregation process is influenced by two sets of segregation parameters, those of the surface region formed by atomic layer 2, and those in the bulk material. This article is the first to conduct a full scale investigation on the influence of surface relaxation on segregation and labelled it the "surface effect".

Thermoforming of glass fibre reinforced polypropylene: A study on the influence of different process parameters

Science.gov (United States)

Schug, Alexander; Winkelbauer, Jonas; Hinterhölzl, Roland; Drechsler, Klaus

2017-10-01

The aim of this study was to analyse the forming behaviour of glass fibre reinforced polypropylene and to identify the influence of several process parameters on the resulting part quality. For this purpose, a complex forming tool was designed, consisting of several areas with single and double curvature. The specimens were produced from unidirectional (UD) tape using the Fiberforge RELAY2000® automated tape laying machine and a subsequent consolidation step. They were then fixed in a support frame, pre-heated in an infrared oven, and formed in the forming tool, which was mounted into a hydraulic heating press. The investigated process parameters were the number and force of the springs in the support frame, the tool temperature and the forming pressure and speed. The layups of the specimens were [0/90/0/90/0¯]s and [0/45/90/-45/0¯]s. After the forming process, the parts were analysed in terms of their quality, with a special focus on wrinkles, undulations, gaps and surface roughness. In addition to optical analysis with a statistical evaluation of the results, 3D scans of the specimens at different steps of the forming process were made to gain an impression of the forming mechanisms and the development of failures. The ATOS system of GOM was used for these 3D scans. The results show that the undulations were influenced by the tool temperature and the spring force. By contrast, the surface quality was most strongly dependent on the forming pressure, which also influenced the size and the number of gaps. The forming speed affected the gaps as well. The tool temperature had the largest influence on the development of wrinkles. As expected, the quasi-isotropic layup showed distinctly more wrinkles and undulations, but it also presented a better surface quality than the orthotropic layup.

Military Influence Operations: Review of Relevant Scientific Literature

National Research Council Canada - National Science Library

Adams, Barbara D; Sartori, Jessica; Waldherr, Sonya

2007-01-01

...) literature and the social influence literature. The persuasion literature argues that messages can be processed either systematically or heuristically, and that messages that are processed more carefully...

Influence of lung parameter values for the Brazilian population on inhalation dose

International Nuclear Information System (INIS)

Reis, Arlene A.; Lopes, Ricardo T.

2009-01-01

The Human Respiratory Tract Model (HRTM) proposed by the ICRP Publication 66 accounts for the morphology and physiology of the respiratory tract. The ICRP 66 presents deposition fraction in the respiratory tract regions considering reference values from Caucasian man. However, in order to obtain a more accurate assessment of intake and dose the ICRP recommends the use of specific information when they are available. The main objective of this study is to evaluate the influence in dose calculation to each region of the respiratory tract when physiological parameters from samples of Brazilian population, in different levels of exercise, are applied in the deposition model.The dosimetric model of HRTM was implemented in the software EXCEL for Windows and committed equivalent dose was determined for each respiratory tract region. First it was calculated the total number of nuclear transformations considering the fractional deposition of activity in each source tissue obtained by application of physiological and morphological Brazilian parameters in the deposition model and then it was calculated the total energy absorbed per unit mass in the target tissue.The variation in the fractional deposition in the compartments of the respiratory tract in changing the physiological parameters from Caucasian to Brazilian adult man causes variation in the number of total transformations and also in the equivalent dose in each region of the respiratory tract. The variations are not the same for all regions of the respiratory tract and depend on levels of exercise. (author)

How to Select the most Relevant Roughness Parameters of a Surface: Methodology Research Strategy

Science.gov (United States)

Bobrovskij, I. N.

2018-01-01

In this paper, the foundations for new methodology creation which provides solving problem of surfaces structure new standards parameters huge amount conflicted with necessary actual floors quantity of surfaces structure parameters which is related to measurement complexity decreasing are considered. At the moment, there is no single assessment of the importance of a parameters. The approval of presented methodology for aerospace cluster components surfaces allows to create necessary foundation, to develop scientific estimation of surfaces texture parameters, to obtain material for investigators of chosen technological procedure. The methods necessary for further work, the creation of a fundamental reserve and development as a scientific direction for assessing the significance of microgeometry parameters are selected.

Normal Force Influence on 3D Texture Parameters Characterizing the Friction Couple Steel – PBT + 10 % PTFE

Directory of Open Access Journals (Sweden)

C. Georgescu

2014-03-01

Full Text Available This study presents the influence of the normal force on the surface quality of the friction couple steel – polybutylene terephthalate (PBT + 10 % polytetrafluoroethylene (PTFE. There were calculated the average values of the amplitude and functional parameters, as obtained from investigating square areas on the wear tracks, with the help of a proposed methodology, for initial and tested surfaces generated on the blocks and on counterpart ring made of rolling bearing steel, for the following test conditions: three normal forces (F = 1 N, F = 2.5 N and F =5 N, three sliding speeds (v = 0.25 m/s, v = 0.50 m/s and v = 0.75 m/s and a sliding distance of L = 7500 m. The conclusion of the research study was that the tested normal force range has an insignificant influence on the surface quality for the tested materials and parameters. This friction couple could be recommended for variable conditions (speed and load in dry regimes.

Influence of geometrical and thermal hydraulic parameters on the short term containment system response

International Nuclear Information System (INIS)

Krishna Chandran, R.; Ali, Seik Mansoor; Balasubramaniyan, V.

2014-01-01

This paper discusses the effect of a number of geometrical and thermal hydraulic parameters on the containment peak pressure following a simulated LOCA. The numerical studies are carried out using an inhouse containment thermal hydraulics program called 'THYCON' with focus only on the short term transient response. In order to highlight the effect of above variables, a geometrically scaled (1:270) model of a typical 220 MWe Indian PHWR containment is considered. The discussions in this paper are limited to explaining the influence of individual parameters by comparing with a base case value. It is essential to mention that the results presented here are not general and should be taken as indicative only. Nevertheless, these numerical studies give insight into short term containment response that would be useful to both the system designer as well as the regulator. (author)

Optimization of parameters of heat exchangers vehicles

Directory of Open Access Journals (Sweden)

Andrei MELEKHIN

2014-09-01

Full Text Available The relevance of the topic due to the decision of problems of the economy of resources in heating systems of vehicles. To solve this problem we have developed an integrated method of research, which allows to solve tasks on optimization of parameters of heat exchangers vehicles. This method decides multicriteria optimization problem with the program nonlinear optimization on the basis of software with the introduction of an array of temperatures obtained using thermography. The authors have developed a mathematical model of process of heat exchange in heat exchange surfaces of apparatuses with the solution of multicriteria optimization problem and check its adequacy to the experimental stand in the visualization of thermal fields, an optimal range of managed parameters influencing the process of heat exchange with minimal metal consumption and the maximum heat output fin heat exchanger, the regularities of heat exchange process with getting generalizing dependencies distribution of temperature on the heat-release surface of the heat exchanger vehicles, defined convergence of the results of research in the calculation on the basis of theoretical dependencies and solving mathematical model.

Analysis of the influence of design parameters of vertically-closed track conveyor with suspended belt and distributed drive on the technical specifications

Directory of Open Access Journals (Sweden)

Tolkachev E.N.

2016-12-01

Full Text Available Using the basic design of the conveyor with suspended belt and distributed drive, a series of numerical calcu-lations was performed. As a result, the influence of design parameters of vertical loop route on the main tech-nical parameters of the conveyor was established. Recommendations on the choice of rational parameters were formulated.

Dynamics of Clinical and Biochemical Parameters in Patients with Liver Cirrhosis Under the Influence of Complex Therapy with Ursodeoxycholic Acid

Directory of Open Access Journals (Sweden)

M.I. Shved

2013-11-01

Full Text Available It was studied dynamics of clinical and biochemical parameters in patients with liver cirrhosis under the influence of complex treatment using ursosan. It is found that the inclusion of ursosan in complex treatment improves clinical and laboratory parameters, significantly reduces the manifestations of general inflammatory liver syndrome, which prevents the progression of the disease.

Influence of parameter settings in voxel-based morphometry 8. Using DARTEL and region-of-interest on reproducibility in gray matter volumetry.

Science.gov (United States)

Goto, M; Abe, O; Aoki, S; Hayashi, N; Miyati, T; Takao, H; Matsuda, H; Yamashita, F; Iwatsubo, T; Mori, H; Kunimatsu, A; Ino, K; Yano, K; Ohtomo, K

2015-01-01

To investigate whether reproducibility of gray matter volumetry is influenced by parameter settings for VBM 8 using Diffeomorphic Anatomical Registration Through Exponentiated Lie Algebra (DARTEL) with region-of-interest (ROI) analyses. We prepared three-dimensional T1-weighted magnetic resonance images (3D-T1WIs) of 21 healthy subjects. All subjects were imaged with each of five MRI systems. Voxel-based morphometry 8 (VBM 8) and WFU PickAtlas software were used for gray matter volumetry. The bilateral ROI labels used were those provided as default settings with the software: Frontal Lobe, Hippocampus, Occipital Lobe, Orbital Gyrus, Parietal Lobe, Putamen, and Temporal Lobe. All 3D-T1WIs were segmented to gray matter with six parameters of VBM 8, with each parameter having between three and eight selectable levels. Reproducibility was evaluated as the standard deviation (mm³) of measured values for the five MRI systems. Reproducibility was influenced by 'Bias regularization (BiasR)', 'Bias FWHM', and 'De-noising filter' settings, but not by 'MRF weighting', 'Sampling distance', or 'Warping regularization' settings. Reproducibility in BiasR was influenced by ROI. Superior reproducibility was observed in Frontal Lobe with the BiasR1 setting, and in Hippocampus, Parietal Lobe, and Putamen with the BiasR3*, BiasR1, and BiasR5 settings, respectively. Reproducibility of gray matter volumetry was influenced by parameter settings in VBM 8 using DARTEL and ROI. In multi-center studies, the use of appropriate settings in VBM 8 with DARTEL results in reduced scanner effect.

Experimental investigation on the influence of instrument settings on pixel size and nonlinearity in SEM image formation

DEFF Research Database (Denmark)

Carli, Lorenzo; Genta, Gianfranco; Cantatore, Angela

2010-01-01

The work deals with an experimental investigation on the influence of three Scanning Electron Microscope (SEM) instrument settings, accelerating voltage, spot size and magnification, on the image formation process. Pixel size and nonlinearity were chosen as output parameters related to image...... quality and resolution. A silicon grating calibrated artifact was employed to investigate qualitatively and quantitatively, through a designed experiment approach, the parameters relevance. SEM magnification was found to account by far for the largest contribution on both parameters under consideration...

Influence of electromagnetic field parameters on the morphology of graphite in grey cast iron

Directory of Open Access Journals (Sweden)

J. Szajnar

2009-01-01

Full Text Available One way to improve the unification of the casting structure may be the application of forced convection of liquid metal during thecrystallization in the form or continuous casting mould. This paper presents the results describing the influence of selected parameters of rotating electromagnetic field enforcing the movement of liquid metal in the form on the morphology of graphite in grey cast iron. The results were fragmented graphite flakes in conditions of regulating the rate of cooling in the range of temperature TZAL

Influence of Operational Parameters on the Photocatalytic Activity of Powdered TiO2 for the Reduction of CO2

Directory of Open Access Journals (Sweden)

Oman Zuas

2014-07-01

Full Text Available In this report, the results from a study on the influence of operational parameters on TiO2 photocatalytic activity for CO2 reduction under an ultraviolet-visible (UV-vis illumination are presented. The results indicated that the TiO2 was found to be active for CO2 reduction with CH3OH as the major products, while other minor products (CO, CH4, and C2H4 were also detected. In addition, the formation of such reduction products was obviously influenced by the operational parameters. Under this study, the optimum operational parameters for CO2 reduction at 298 °K were determined to be: NaOH concentration 0.2 M, TiO2 dosage 2 g/L, volume of the reaction media 75 mL, the pressure of system 800 kPa. It was also found that the increase in UV-vis illumination time have increased the yield of product formation. A possible reaction pathway for the formation of the reduction products is also discussed.

Influence of multiple bioprocess parameters on production of lipase from Pseudomonas sp. BWS-5

Directory of Open Access Journals (Sweden)

Balwinder Singh Sooch

2013-10-01

Full Text Available The aim of the present work was to study the influence of multiple bioprocess parameters for the maximum production of lipase from Pseudomonas sp. BWS-5. The culture reached the stationary phase of growth after 36h of incubation when the maximum lipase production was obtained at flask level. The different media components such as carbon sources, nitrogen sources, trace elements and process parameters such as the pH of the medium, temperature and time of incubation, agitation/stationary conditions, etc. were optimized at flask level and at bioreactor level. The maximum enzyme production of 298 IU/mL was obtained with the use of simple medium with pH 6.5 containing glucose (1 %, w/v, peptone (3 %, w/v and KCl (0.05 %, w/v after 30h of incubation at 37°C under agitation (200 rpm conditions with 0.75 vvm of air supply.

Process parameter influence on Electro-sinter-forging (ESF) of titanium discs

DEFF Research Database (Denmark)

Cannella, Emanuele; Nielsen, Chris Valentin; Bay, Niels

Electro-sinter-forging (ESF) is an innovative sintering process based on the principle of electrical Joule heating. The electrical current is flowing through the powder compact, which is under mechanical pressure. As compared to conventional sintering [1] and spark plasma sintering [2], the main...... advantages are the decreased sintering time and high relative density [3]. Near net-shape components can be manufactured and post-removal processing is limited to surface polishing. The present work is focused on analysing the influence of the main process parameters, namely compacting pressure, sintering...... time and electrical current density, on the final density of a disc sample made from commercially pure titanium powder. The maximum achieved relative density was 94% of the bulk density of pure titanium. The density estimation was carried out by using both Archimedes’ and 3D scanning....

Influence of the milling time in the microstructural parameters of TA2O5-Al powder refined by Rietveld method

International Nuclear Information System (INIS)

Brito, R.A.; Mendes, M.W.D.; Alves Junior, C.; Costa, F.A. da; Gomes, U.U.

2009-01-01

Mechanical alloying (MA) is a solid-state powder processing technique involving repeated welding, fracturing, and re-welding of powder particles in a high energy mill. This process is used for producing of fine powders containing unique microstructures. The process starts with mixing of the powders in the desired proportion. Then, the mixture is milled using the established time in the high-energy mill. The powder particles are submitted to repeated cycles of cold working and fracture, and the final product correspond to a composite powder, containing characteristics different of the initial constituents. Ta 2 O 5 -Al powders were milled in a planetary ball mill for different times in order to evaluate the influence of the milling time in their microstructural parameters like crystallite size and micro deformation. The microstructural parameters were obtained by the Rietveld Method. The results showed that the microstructural parameters were influenced by the increase of the milling time. (author)

Influence of waste managemental and technical planning parameters on plant costs; Einfluss abfallwirtschaftlicher und technischer Plannungsgroessen auf die Anlagenkosten

Energy Technology Data Exchange (ETDEWEB)

Beckmann, R. [Inst. fuer Umwelt, Sicherheits- und Energietechnik e.V., Oberhausen (Germany)

1998-09-01

The probable future costs of thermal waste treatment depend on a great number of influencing factors. One of the essential aims of the present contribution is to elaborate and present the sensitivity of costs to various parameters. [Deutsch] Die zukuenftig zu erwartenden Kosten der thermischen Abfallbehandlung haengen von einer Vielzahl von Einflussgroessen ab. Im Rahmen des Beitrags besteht daher ein wesentliches Ziel darin, die Sensitivitaet der Kosten hinsichtlich verschiedenster Parameter herauszuarbeiten und darzustellen. (orig./SR)

Influence of physical properties and operating parameters on hydrodynamics in Centrifugal Partition Chromatography.

Science.gov (United States)

Adelmann, S; Schembecker, G

2011-08-12

Besides the selection of a suitable biphasic solvent system the separation efficiency in Centrifugal Partition Chromatography (CPC) is mainly influenced by the hydrodynamics in the chambers. The flow pattern, the stationary phase retention and the interfacial area for mass transfer strongly depend on physical properties of the solvent system and operating parameters. In order to measure these parameters we visualized the hydrodynamics in a FCPC-chamber for five different solvent systems with an optical measurement system and calculated the stationary phase retention, interfacial area and the distribution of mobile phase thickness in the chamber. Although inclined chambers were used we found that the Coriolis force always deflected the mobile phase towards the chamber wall reducing the interfacial area. This effect increased for systems with low density difference. We also have shown that the stability of phase systems (stationary phase retention) and its tendency to disperse increased for smaller values of the ratio of interfacial tension and density difference. But also the viscosity ratio and the flow pattern itself had a significant effect on retention and dispersion of the mobile phase. As a result operating parameters should be chosen carefully with respect to physical properties for a CPC system. In order to reduce the effect of the Coriolis force CPC devices with greater rotor radius are desirable. Copyright © 2011 Elsevier B.V. All rights reserved.

Review on Parameters Influencing the Rice Breakage and Rubber Roll Wear in Sheller

Directory of Open Access Journals (Sweden)

Prabhakaran P.

2017-09-01

Full Text Available The present review deals with parameters influencing the rice breakage during rice milling operations and the effect of rubber roll Sheller in rice husk removal process. The main objective of rice milling system is to remove the husk and bran layer to produce the white rice. In this process, rubber roll sheller is used to remove husk from the grains by friction process. If the rubber material is too soft, there may not be sufficient shear force to husk the paddy. Wear will be minimum for rubber material with high hardness but indeed it pronounce the breakage of rice. Hence, for efficient husking the rubber roll material should possess the balance of physico-mechanical properties. Rice breakage depends on several other parameters like the type of harvest, drying temperature, drying methods, physical characteristics of paddy, husking characteristics, paddy moisture content, rubber roller speed, rubber roll pressure, paddy feed rate and fissures. Rubber roll wear depends on the type of rubber material attached to the roller, feed rate, roller speed, pressure etc.

Influence of the synthesis route and parameters on the thermoluminescence response of ZnO phosphors

International Nuclear Information System (INIS)

Orante B, V.; Bernal, R.; Brown, F.; Castano, V.M.; Cruz V, C.

2007-01-01

Full text: ZnO nano phosphors obtained by thermal annealing of chemically synthesized ZnS powder has been recently reported to exhibit striking properties to be used as thermoluminescence (TL) dosimeters for intermediate and high doses of ionizing radiation. Encouraged by these results, we began a research focused to improve the process of fabrication of ZnO phosphors, by varying the chemical route and parameters of synthesis in each route. We essayed three different chemical ways to obtain ZnO. In each case, different sintering processes were applied to the product obtained from the chemical reaction. TL is very sensitive to impurities traces, whose incorporation is influenced by the synthesis history, so that we obtain that general features of TL glow curves can be tuned by controlling the synthesis parameters. (Author)

Laser cutting: industrial relevance, process optimization, and laser safety

Science.gov (United States)

Haferkamp, Heinz; Goede, Martin; von Busse, Alexander; Thuerk, Oliver

1998-09-01

Compared to other technological relevant laser machining processes, up to now laser cutting is the application most frequently used. With respect to the large amount of possible fields of application and the variety of different materials that can be machined, this technology has reached a stable position within the world market of material processing. Reachable machining quality for laser beam cutting is influenced by various laser and process parameters. Process integrated quality techniques have to be applied to ensure high-quality products and a cost effective use of the laser manufacturing plant. Therefore, rugged and versatile online process monitoring techniques at an affordable price would be desirable. Methods for the characterization of single plant components (e.g. laser source and optical path) have to be substituted by an omnivalent control system, capable of process data acquisition and analysis as well as the automatic adaptation of machining and laser parameters to changes in process and ambient conditions. At the Laser Zentrum Hannover eV, locally highly resolved thermographic measurements of the temperature distribution within the processing zone using cost effective measuring devices are performed. Characteristic values for cutting quality and plunge control as well as for the optimization of the surface roughness at the cutting edges can be deducted from the spatial distribution of the temperature field and the measured temperature gradients. Main influencing parameters on the temperature characteristic within the cutting zone are the laser beam intensity and pulse duration in pulse operation mode. For continuous operation mode, the temperature distribution is mainly determined by the laser output power related to the cutting velocity. With higher cutting velocities temperatures at the cutting front increase, reaching their maximum at the optimum cutting velocity. Here absorption of the incident laser radiation is drastically increased due to

ANALYSIS OF THE INFLUENCE OF PARAMETERS OF CONTROL OF HEATING POWER GENERATING UNITS ON FUEL CONSUMPTION

Directory of Open Access Journals (Sweden)

Shchinnikov P.A.

2011-04-01

Full Text Available It is presented analysis of the influence of parameters of state of the process of control on the increase of the fuel consumption of heat power generating units. There are presented results of calculations of the increase of the fuel consumption at the deviation of the working steam temperature and pressure from rated values. Result of calculus is compared with the experiment.

Influence of amplitude-related perfusion parameters in the parotid glands by non-fat-saturated dynamic contrast-enhanced magnetic resonance imaging

Energy Technology Data Exchange (ETDEWEB)

Chiu, Su-Chin [Graduate Institute of Biomedical Electronics and Bioinformatics, National Taiwan University, Taipei 106, Taiwan, Republic of China and Department of Radiology, Tri-Service General Hospital, Taipei 114, Taiwan (China); Cheng, Cheng-Chieh [Department of Radiology, Brigham and Women’s Hospital, Harvard Medical School, Boston, Massachusetts 02115 (United States); Chang, Hing-Chiu [Department of Diagnostic Radiology, The University of Hong Kong (Hong Kong); Chung, Hsiao-Wen [Graduate Institute of Biomedical Electronics and Bioinformatics, National Taiwan University, Taipei 106, Taiwan (China); Department of Radiology, Tri-Service General Hospital, Taipei 114, Taiwan (China); Department of Radiology, National Defense Medical Center, Taipei 114, Taiwan (China); Chiu, Hui-Chu [Ph.D. Program of Technology Management, Chung Hua University, Hsinchu 300, Taiwan (China); Liu, Yi-Jui [Department of Automatic Control Engineering, Feng-Chia University, Taichung 407, Taiwan (China); Hsu, Hsian-He; Juan, Chun-Jung, E-mail: peterjuancj@yahoo.com.tw [Department of Radiology, Tri-Service General Hospital, Taipei 114, Taiwan and Department of Radiology, National Defense Medical Center, Taipei 114, Taiwan (China)

2016-04-15

Purpose: To verify whether quantification of parotid perfusion is affected by fat signals on non-fat-saturated (NFS) dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI) and whether the influence of fat is reduced with fat saturation (FS). Methods: This study consisted of three parts. First, a retrospective study analyzed DCE-MRI data previously acquired on different patients using NFS (n = 18) or FS (n = 18) scans. Second, a phantom study simulated the signal enhancements in the presence of gadolinium contrast agent at six concentrations and three fat contents. Finally, a prospective study recruited nine healthy volunteers to investigate the influence of fat suppression on perfusion quantification on the same subjects. Parotid perfusion parameters were derived from NFS and FS DCE-MRI data using both pharmacokinetic model analysis and semiquantitative parametric analysis. T tests and linear regression analysis were used for statistical analysis with correction for multiple comparisons. Results: NFS scans showed lower amplitude-related parameters, including parameter A, peak enhancement (PE), and slope than FS scans in the patients (all with P < 0.0167). The relative signal enhancement in the phantoms was proportional to the dose of contrast agent and was lower in NFS scans than in FS scans. The volunteer study showed lower parameter A (6.75 ± 2.38 a.u.), PE (42.12% ± 14.87%), and slope (1.43% ± 0.54% s{sup −1}) in NFS scans as compared to 17.63 ± 8.56 a.u., 104.22% ± 25.15%, and 9.68% ± 1.67% s{sup −1}, respectively, in FS scans (all with P < 0.005). These amplitude-related parameters were negatively associated with the fat content in NFS scans only (all with P < 0.05). Conclusions: On NFS DCE-MRI, quantification of parotid perfusion is adversely affected by the presence of fat signals for all amplitude-related parameters. The influence could be reduced on FS scans.

Influence of amplitude-related perfusion parameters in the parotid glands by non-fat-saturated dynamic contrast-enhanced magnetic resonance imaging

International Nuclear Information System (INIS)

Chiu, Su-Chin; Cheng, Cheng-Chieh; Chang, Hing-Chiu; Chung, Hsiao-Wen; Chiu, Hui-Chu; Liu, Yi-Jui; Hsu, Hsian-He; Juan, Chun-Jung

2016-01-01

Purpose: To verify whether quantification of parotid perfusion is affected by fat signals on non-fat-saturated (NFS) dynamic contrast-enhanced magnetic resonance imaging (DCE-MRI) and whether the influence of fat is reduced with fat saturation (FS). Methods: This study consisted of three parts. First, a retrospective study analyzed DCE-MRI data previously acquired on different patients using NFS (n = 18) or FS (n = 18) scans. Second, a phantom study simulated the signal enhancements in the presence of gadolinium contrast agent at six concentrations and three fat contents. Finally, a prospective study recruited nine healthy volunteers to investigate the influence of fat suppression on perfusion quantification on the same subjects. Parotid perfusion parameters were derived from NFS and FS DCE-MRI data using both pharmacokinetic model analysis and semiquantitative parametric analysis. T tests and linear regression analysis were used for statistical analysis with correction for multiple comparisons. Results: NFS scans showed lower amplitude-related parameters, including parameter A, peak enhancement (PE), and slope than FS scans in the patients (all with P < 0.0167). The relative signal enhancement in the phantoms was proportional to the dose of contrast agent and was lower in NFS scans than in FS scans. The volunteer study showed lower parameter A (6.75 ± 2.38 a.u.), PE (42.12% ± 14.87%), and slope (1.43% ± 0.54% s"−"1) in NFS scans as compared to 17.63 ± 8.56 a.u., 104.22% ± 25.15%, and 9.68% ± 1.67% s"−"1, respectively, in FS scans (all with P < 0.005). These amplitude-related parameters were negatively associated with the fat content in NFS scans only (all with P < 0.05). Conclusions: On NFS DCE-MRI, quantification of parotid perfusion is adversely affected by the presence of fat signals for all amplitude-related parameters. The influence could be reduced on FS scans.

Pragmatic inferences and self-relevant judgments

DEFF Research Database (Denmark)

Puente-Diaz, Rogelio; Cavazos Arroyo, Judith; Brem, Alexander

2016-01-01

Three studies examined the influence of type of scale on self-relevant judgments and the moderating role of age, prevention, focus, and need for cogni- tion. Participants were randomly assigned to a bipolar or a unipolar scale condition in all three studies. Results from study 1 with a representa...

Influence of the power supply parameters on the projectile energy in the permanent magnet electrodynamic accelerator

Science.gov (United States)

Waindok, Andrzej; Piekielny, Paweł

2017-10-01

The main objective of the research is to investigate, how the power supply parameters influence the kinetic energy of the movable element, called commonly a projectile or bullet. A calculation and measurement results of transient characteristics for an electrodynamic accelerator with permanent magnet support were presented in the paper. The calculations were made with using field-circuit model, which includes the parameters of the power supply, mass of the bullet and friction phenomenon. Characteristics of energy and muzzle velocity verso supply voltage (50 V to 350 V) and capacitance value (60 mF to 340.5 mF) were determined, as well. A measurement verification of selected points of calculation characteristics were carried out for investigated values of muzzle velocity. A good conformity between calculation and measurement results was obtained. Concluding, presented characteristics of the muzzle velocity and energy of the projectile vs. power supply parameters indicate, that accelerators could be used for fatigue testing of materials.

Influence of the power supply parameters on the projectile energy in the permanent magnet electrodynamic accelerator

Directory of Open Access Journals (Sweden)

Waindok Andrzej

2017-01-01

Full Text Available The main objective of the research is to investigate, how the power supply parameters influence the kinetic energy of the movable element, called commonly a projectile or bullet. A calculation and measurement results of transient characteristics for an electrodynamic accelerator with permanent magnet support were presented in the paper. The calculations were made with using field-circuit model, which includes the parameters of the power supply, mass of the bullet and friction phenomenon. Characteristics of energy and muzzle velocity verso supply voltage (50 V to 350 V and capacitance value (60 mF to 340.5 mF were determined, as well. A measurement verification of selected points of calculation characteristics were carried out for investigated values of muzzle velocity. A good conformity between calculation and measurement results was obtained. Concluding, presented characteristics of the muzzle velocity and energy of the projectile vs. power supply parameters indicate, that accelerators could be used for fatigue testing of materials.

Investigation of the influence of modified parameters in the atmospheric dispersion model on the results of the German Risk Study (DRS)

International Nuclear Information System (INIS)

Vogt, S.; Wittek, P.

1982-04-01

A substantial criterion in preparing Phase A of the German Risk Study was its comparability with the U. S. Reactor Safety Study. Therefore, a number of basic assumptions and methodological principles were to be identical with those adopted in the American study. For Phase B of the German Risk Study improvements of the method will be used to a greater extent and recent results of research work taken into account. A first step in this direction will consists in investigating the influence exerted by modified parameters in the dispersion submodel. The other parameters, besides dry and wet deposition, are the height of the mixing layer, the dispersion parameters and the wind direction. Furthermore, the degree will be studied at which the selection of weather sequences have an influence on the collective risks. All results indicated will be related to the results obtained in Phase A. (orig.) [de

The influence of design parameters on the performance of FBAR in 10-14 GHz

Science.gov (United States)

Nor, N. I. M.; Osman, R. A. M.; Idris, M. S.; Khalid, N.; Mohamad Isa, M.; Ahmad, N.; Mat Isa, Siti S.; Ramli, Muhammad M.; Kasjoo, S. R.

2017-11-01

This research presents the analysis of the influence of design parameters on the performance of film bilk acoustic wave resonator (FBAR) working from 10 GHz to 14 GHz. The analysis is done by implementing one-dimensional (1-D) modellings, which are 1-D Mason model and Butterworth Van Dyke (BVD) model. The physical parameters such as piezoelectric materials and its thickness, and size of area affecting the characteristics of the FBAR are analyzed in detail. Zinc oxide (ZnO) and aluminum nitride (AlN) are chosen as the piezoelectric materials. The resonance area is varied at 25μm×25μm to 35μm×35μm. From the analysis, it is found that as the frequency increases, the thickness of the piezoelectric material decreases. Meanwhile, the static capacitance increases as the frequency increases. It is also found that as the area increases, the electrical impedance and static capacitance also increases.

The foundation of the concept of relevance

DEFF Research Database (Denmark)

Hjørland, Birger

2010-01-01

that what was regarded as the most fundamental view by Saracevic in 1975 has not since been considered (with very few exceptions). Other views, which are based on less fruitful assumptions, have dominated the discourse on relevance in information retrieval and information science. Many authors have...... reexamined the concept of relevance in information science, but have neglected the subject knowledge view, hence basic theoretical assumptions seem not to have been properly addressed. It is as urgent now as it was in 1975 seriously to consider “the subject knowledge view” of relevance (which may also...... be termed “the epistemological view”). The concept of relevance, like other basic concepts, is influenced by overall approaches to information science, such as the cognitive view and the domain-analytic view. There is today a trend toward a social paradigm for information science. This paper offers...

The Influence of High Iodine Intake on Chosen Blood Parameters of Sheep

Directory of Open Access Journals (Sweden)

Hana Dušová

2014-01-01

Full Text Available The objective of the study was to evaluate the influence of high iodine intake in ewes on haematological and biochemical parameters of the blood of ewes and their lambs. Twelve pregnant ewes of the Sumava sheep breed and their newborn lambs were included in the experiment. Control group (A consisted of 6 ewes with 7 lambs and experimental group (B comprised 6 ewes with 6 lambs. The feed ration was enriched with calcium iodate by addition of 3 and 5 mg/kg in group A and group B, respectively. The studied parameters in ewes and lambs were haematocrit value, red blood cell count and haemoglobin concentration in blood, concentration of urea and total proteins, and alkaline phosphatase activity in blood plasma. No differences were found out in haematocrit value, red blood cell count, concentration of haemoglobin and total proteins between groups of ewes A and B with their lambs. Urea concentration and alkaline phosphatase activity were higher in ewes of group B and their lambs during the entire experimental period. An increase in the values of urea and alkaline phosphatase in the group of ewes and lambs with higher iodine intake indicates a potential risk of high iodine intake associated with changes in the thyroid activity in ewes and their lambs.

Parameters influencing the yield and composition of the essential oil from Cretan Vitex agnus-castus fruits.

Science.gov (United States)

Sørensen, J M; Katsiotis, S T

2000-04-01

Mature and immature fruits of a Cretan Vitex agnus-castus L. population were chosen to investigate different parameters such as comminution, maturity, distillation period and extraction method influencing the essential oil yield and composition. The effect of the comminution and the maturity of the plant material showed highly significant differences in yield and composition of the essential oils obtained, as well as the distillation duration from one to five hours and the method applied (hydrodistillation and simultaneous distillation extraction). The variation of 36 essential oil components due to the parameters applied was studied. The results showed that many different essential oil qualities can be obtained from the same plant material according to the parameters employed in its extraction. Entire fruits hydrodistilled for one hour yielded an oil much richer in monoterpene hydrocarbons and oxygenated compounds whereas the best combination to obtain an oil rich in less volatile compounds is by SDE of comminuted fruits for five hours. For mature fruits the main components varied as follows due to the parameters studied: sabinene 16.4-44.1%, 1,8-cineole 8.4-15.2%, beta-caryophyllene 2.1-5.0%, and trans-beta-farnesene 5.0-11.7%.

The influence of petroleum products on the methane fermentation process.

Science.gov (United States)

Choromański, Paweł; Karwowska, Ewa; Łebkowska, Maria

2016-01-15

In this study the influence of the petroleum products: diesel fuel and spent engine oil on the sewage sludge digestion process and biogas production efficiency was investigated. Microbiological, chemical and enzymatic analyses were applied in the survey. It was revealed that the influence of the petroleum derivatives on the effectiveness of the methane fermentation of sewage sludge depends on the type of the petroleum product. Diesel fuel did not limit the biogas production and the methane concentration in the biogas, while spent engine oil significantly reduced the process efficacy. The changes in physical-chemical parameters, excluding COD, did not reflect the effect of the tested substances. The negative influence of petroleum products on individual bacterial groups was observed after 7 days of the process, while after 14 days probably some adaptive mechanisms appeared. The dehydrogenase activity assessment was the most relevant parameter to evaluate the effect of petroleum products contamination. Diesel fuel was probably used as a source of carbon and energy in the process, while the toxic influence was observed in case of spent engine oil. Copyright © 2015 Elsevier B.V. All rights reserved.

Improving the GIS-DRP Approach by Means of DelineatingRunoff Characteristics with New Discharge Relevant Parameters

Directory of Open Access Journals (Sweden)

Marco Hümann

2013-01-01

Full Text Available At present it is common to use geographic information system (GIS applications to assess runoff generation. One of these GIS-based tools to generate maps of dominant runoff processes is the so called GIS-DRP approach. The tool, which has been developed mainly based on agricultural areas, uses commonly available input data like a digital elevation model (DEM, geological information as well as land use information. The aim of this study is to test, validate and improve this GIS-DRP method for forested and silviculture areas. Hence, soil-hydrologic investigations and several mapping techniques of dominant runoff processes were conducted on 25 test-plots in four forested catchments in Rhineland-Palatinate (Germany and the Grand Duchy of Luxembourg. By comparing the results of the mapping techniques and those of the test plots, weak points in the original GIS-DRP method were detected. Subsequently, it was possible to enhance the GIS-DRP approach by incorporating new discharge relevant parameters like topsoil sealing, extreme weather events and semipermeability of the substratum. Moreover, the improved GIS-DRP approach can be widely used in different landscapes and for different fields of application. The adapted method can now support foresters and decision makers in forestry planning, answer questions concerning the landscape water balance and peripheral water retention or provide extra information for sustainable forest planning in times of a changing climate.

The influence of the statistical distributed parameters of the shape of the magneto-resistive transition of a HTc superconductor

International Nuclear Information System (INIS)

Grobnic, D.; Popescu, I.M.

1993-01-01

As a result of their granular structure the conductance of ceramic high temperature superconductors depends strongly on the characteristics of the parameter distribution. To study the influence of these distributions of the magneto-resistive transition from normal to superconductive state, a mathematical model was used. This model simulates the superconductor sample, considered as large three-dimensional collection of Josephson tunnel junctions. Each individual junction, according to the values of the parameters that define it, in a given environment (temperature, magnetic field and current density) allows or not the supercurrent to flow with a given probability. The bond percolation problem was solved using a Monte Carlo procedure. To solve the random resistor network formed, a sparse matrix package was used. As parameters that defined Josephson junction which choose the resistance of the normal junction state and the critical temperature of the grain. We considered the normal junction resistance as obeying a log normal distribution and the critical temperature, a Gaussian one. The influences of the relative dispersion of the first distribution and the dispersion of the critical temperature distribution on the shape of the resistivity versus magnetic field was studied. (Author)

Influence of extrinsic operational parameters on salt diffusion during ultrasound assisted meat curing.

Science.gov (United States)

Inguglia, Elena S; Zhang, Zhihang; Burgess, Catherine; Kerry, Joseph P; Tiwari, Brijesh K

2018-02-01

The present study investigated the effect of geometric parameters of the ultrasound instrument during meat salting in order to enhance salt diffusion and salt distribution in pork meat on a lab scale. The effects of probe size (∅2.5 and 1.3cm) and of different distances between the transducer and the meat sample (0.3, 0.5, and 0.8cm) on NaCl diffusion were investigated. Changes in the moisture content and NaCl gain were used to evaluate salt distribution and diffusion in the samples, parallel and perpendicular to ultrasound propagation direction. Results showed that 0.3cm was the most efficient distance between the probe and the sample to ensure a higher salt diffusion rate. A distance of 0.5cm was however considered as a trade-off distance to ensure salt diffusion and maintenance of meat quality parameters. The enhancement of salt diffusion by ultrasound was observed to decrease with increased horizontal distance from the probe. This study is of valuable importance for meat processing industries willing to apply new technologies on a larger scale and with defined operational standards. The data suggest that the geometric parameters of ultrasound systems can have strong influence on the efficiency of ultrasonic enhancement of NaCl uptake in meat and can be a crucial element in determining salt uptake during meat processing. Copyright © 2017 Elsevier B.V. All rights reserved.

Trace metals, melanin-based pigmentation and their interaction influence immune parameters in feral pigeons (Columba livia).

Science.gov (United States)

Chatelain, M; Gasparini, J; Frantz, A

2016-04-01

Understanding the effects of trace metals emitted by anthropogenic activities on wildlife is of great concern in urban ecology; yet, information on how they affect individuals, populations, communities and ecosystems remains scarce. In particular, trace metals may impact survival by altering the immune system response to parasites. Plumage melanin is assumed to influence the effects of trace metals on immunity owing to its ability to bind metal ions in feathers and its synthesis being coded by a pleiotropic gene. We thus hypothesized that trace metal exposure would interact with plumage colouration in shaping immune response. We experimentally investigated the interactive effect between exposure to an environmentally relevant range of zinc and/or lead and melanin-based plumage colouration on components of the immune system in feral pigeons (Columba livia). We found that zinc increased anti-keyhole limpet hemocyanin (KLH) IgY primary response maintenance, buffered the negative effect of lead on anti-KLH IgY secondary response maintenance and tended to increase T-cell mediated phytohaemagglutinin (PHA) skin response. Lead decreased the peak of the anti-KLH IgY secondary response. In addition, pheomelanic pigeons exhibited a higher secondary anti-KLH IgY response than did eumelanic ones. Finally, T-cell mediated PHA skin response decreased with increasing plumage eumelanin level of birds exposed to lead. Neither treatments nor plumage colouration correlated with endoparasite intensity. Overall, our study points out the effects of trace metals on some parameters of birds' immunity, independently from other confounding urbanization factors, and underlines the need to investigate their impacts on other life history traits and their consequences in the ecology and evolution of host-parasite interactions.

Numerical research of influence of laser radiation parameters on the formation of intermetallic phases from metal powders in selective laser melting technology

Science.gov (United States)

Agapovichev, A. V.; Knyazeva, A. G.; Smelov, V. G.

2017-10-01

A large number of factors influence the quality of the material obtained with selective laser melting. Through correct understanding and managing these factors, it is possible to achieve the necessary quality of the materials, which is highly competitive to the traditional production methods. The technique of selective laser melting is a complex process in which a large number of parameters affect the quality of the final product. The complexity of the process of selective laser melting consists of many thermal, physical and chemical interactions, which are influenced by a large number of parameters. The main parameters of SLM are scanning rate, laser radiation power and layer thickness. In the framework of this paper, there was made an attempt to take into account real physical and chemical processes taking place during the selective laser melting of an Ni-Al alloy.

The Influence of Xylanase Supplementation on Dough Rheology Concerning its Consistograph Parameters

Directory of Open Access Journals (Sweden)

Rodica Chereji

2010-05-01

Full Text Available In this study we determined the influence of xylanase supplementation on dough rheology concerning its consistograph parameters: maximum pressure (Pr max, (mb and water absorption (Wa, %. The consistograph analyses were conducted at constant hydration and consistency of 500UF. Determinations were made on 4 types of flour and optimal enzyme dosages were determined. Then we added the optimal enzyme dose for each type of flour as follows: F1, F2, F3, F4: P1-8100U.FXU/100kg flour, P2-16200U.FXU/100kg flour, P3-24300U.FXU/100kg flour. Fungal xylanase used in these concentrations led to the improvement of bread quality properties: finer texture of the crumb, extending freshness of bread, improving the colour and flavour, improving the slicing ability.

New parameters influencing hydraulic runner lifetime

International Nuclear Information System (INIS)

Sabourin, M; Bouffard, D A; Thibault, D; Levesque, M

2010-01-01

Traditionally, hydraulic runner mechanical design is based on calculation of static stresses. Today, validation of hydraulic runner design in terms of reliability requires taking into account the fatigue effect of dynamics loads. A damage tolerant approach based on fracture mechanics is the method chosen by Alstom and Hydro-Quebec to study fatigue damage in runners. This requires a careful examination of all factors influencing material fatigue behavior. Such material behavior depends mainly on the chemical composition, microstructure and thermal history of the component, and on the resulting residual stresses. Measurement of fracture mechanics properties of various steels have demonstrated that runner lifetime can be significantly altered by differences in the manufacturing process, although remaining in accordance with agreed practices and standards such as ASTM. Carbon content and heat treatment are suspected to influence fatigue lifetime. This will have to be investigated by continuing the current research.

New parameters influencing hydraulic runner lifetime

Energy Technology Data Exchange (ETDEWEB)

Sabourin, M; Bouffard, D A [Alstom Hydro Canada Inc, Hydraulic Engineering, 1350 chemin St-Roch, Sorel-Tracy (Quebec), J3P 5P9 (Canada); Thibault, D [Hydro-Quebec, Institut de Recherche d' Hydro-Quebec 1800 boul. Lionel-Boulet, Varennes (Quebec), J3X 1S1 (Canada); Levesque, M, E-mail: michel.sabourin@power.alstom.co [Ecole Polytechnique de Montreal, Departement de genie mecanique C.P.6079, succ. Centre-ville, Montreal (Quebec), H3C 3A7 (Canada)

2010-08-15

Traditionally, hydraulic runner mechanical design is based on calculation of static stresses. Today, validation of hydraulic runner design in terms of reliability requires taking into account the fatigue effect of dynamics loads. A damage tolerant approach based on fracture mechanics is the method chosen by Alstom and Hydro-Quebec to study fatigue damage in runners. This requires a careful examination of all factors influencing material fatigue behavior. Such material behavior depends mainly on the chemical composition, microstructure and thermal history of the component, and on the resulting residual stresses. Measurement of fracture mechanics properties of various steels have demonstrated that runner lifetime can be significantly altered by differences in the manufacturing process, although remaining in accordance with agreed practices and standards such as ASTM. Carbon content and heat treatment are suspected to influence fatigue lifetime. This will have to be investigated by continuing the current research.

Dynamics of cardiovascular parameters in combined aortic malformations under the influence of a physical therapy program during the rehabilitation process

Directory of Open Access Journals (Sweden)

Serhii Kalmykov

2017-12-01

Full Text Available Purpose: to study hemodynamic parameters and the reaction of the cardiovascular system to the dosed physical load of patients combined aortic defect with heart failure of the I degree under the influence of the complex physical therapy program developed by us during the rehabilitation process. Material & Methods: the study involved 26 middle-aged men with a diagnosis: combined aortic valve disease, HF I st. Result: dynamics of functional parameters of the cardiovascular system of patients under the influence of the physical therapy program is analyzed. Conclusion: the combination of morning hygienic gymnastics, therapeutic gymnastics, independent activities and dosed walking with a therapeutic massage contributes to the normalization of vascular tone, motor-vascular reflexes and blood pressure, increasing the tolerance of the cardiovascular system to physical activity.

Si-based thin film coating on Y-TZP: Influence of deposition parameters on adhesion of resin cement

Energy Technology Data Exchange (ETDEWEB)

Queiroz, José Renato Cavalcanti, E-mail: joserenatocq@hotmail.com [Potiguar University, Department of Biotechnology, Natal (Brazil); Nogueira Junior, Lafayette [São Paulo State University, Department of Prosthodontics and Dental Materials, São José dos Campos (Brazil); Massi, Marcos [Federal University of São Paulo, Institute of Science and Technology, São José dos Campos (Brazil); Silva, Alecssandro de Moura; Bottino, Marco Antonio [São Paulo State University, Department of Prosthodontics and Dental Materials, São José dos Campos (Brazil); Sobrinho, Argemiro Soares da Silva [Technological Institute of Aeronautics, Department of Physics, São José dos Campos (Brazil); Özcan, Mutlu [University of Zurich, Dental Materials Unit, Center for Dental and Oral Medicine, Clinic for Fixed and Removable Prosthodontics and Dental Materials Science, Zurich (Switzerland)

2013-10-01

This study evaluated the influence of deposition parameters for Si-based thin films using magnetron sputtering for coating zirconia and subsequent adhesion of resin cement. Zirconia ceramic blocks were randomly divided into 8 groups and specimens were either ground finished and polished or conditioned using air-abrasion with alumina particles coated with silica. In the remaining groups, the polished specimens were coated with Si-based film coating with argon/oxygen magnetron discharge at 8:1 or 20:1 flux. In one group, Si-based film coating was performed on air-abraded surfaces. After application of bonding agent, resin cement was bonded. Profilometry, goniometry, Energy Dispersive X-ray Spectroscopy and Rutherford Backscattering Spectroscopy analysis were performed on the conditioned zirconia surfaces. Adhesion of resin cement to zirconia was tested using shear bond test and debonded surfaces were examined using Scanning Electron Microscopy. Si-based film coating applied on air-abraded rough zirconia surfaces increased the adhesion of the resin cement (22.78 ± 5.2 MPa) compared to those of other methods (0–14.62 MPa) (p = 0.05). Mixed type of failures were more frequent in Si film coated groups on either polished or air-abraded groups. Si-based thin films increased wettability compared to the control group but did not change the roughness, considering the parameters evaluated. Deposition parameters of Si-based thin film and after application of air-abrasion influenced the initial adhesion of resin cement to zirconia.

Si-based thin film coating on Y-TZP: Influence of deposition parameters on adhesion of resin cement

International Nuclear Information System (INIS)

Queiroz, José Renato Cavalcanti; Nogueira Junior, Lafayette; Massi, Marcos; Silva, Alecssandro de Moura; Bottino, Marco Antonio; Sobrinho, Argemiro Soares da Silva; Özcan, Mutlu

2013-01-01

This study evaluated the influence of deposition parameters for Si-based thin films using magnetron sputtering for coating zirconia and subsequent adhesion of resin cement. Zirconia ceramic blocks were randomly divided into 8 groups and specimens were either ground finished and polished or conditioned using air-abrasion with alumina particles coated with silica. In the remaining groups, the polished specimens were coated with Si-based film coating with argon/oxygen magnetron discharge at 8:1 or 20:1 flux. In one group, Si-based film coating was performed on air-abraded surfaces. After application of bonding agent, resin cement was bonded. Profilometry, goniometry, Energy Dispersive X-ray Spectroscopy and Rutherford Backscattering Spectroscopy analysis were performed on the conditioned zirconia surfaces. Adhesion of resin cement to zirconia was tested using shear bond test and debonded surfaces were examined using Scanning Electron Microscopy. Si-based film coating applied on air-abraded rough zirconia surfaces increased the adhesion of the resin cement (22.78 ± 5.2 MPa) compared to those of other methods (0–14.62 MPa) (p = 0.05). Mixed type of failures were more frequent in Si film coated groups on either polished or air-abraded groups. Si-based thin films increased wettability compared to the control group but did not change the roughness, considering the parameters evaluated. Deposition parameters of Si-based thin film and after application of air-abrasion influenced the initial adhesion of resin cement to zirconia.

Influence of Parameters of a Printing Plate on Photoluminescence of Nanophotonic Printed Elements of Novel Packaging

Directory of Open Access Journals (Sweden)

Olha Sarapulova

2015-01-01

Full Text Available In order to produce nanophotonic elements for smart packaging, we investigated the influence of the parameters of screen and offset gravure printing plates on features of printed application of coatings with nanophotonic components and on parameters of their photoluminescence. To determine the dependence of luminescence intensity on the thickness of solid coating, we carried out the formation of nanophotonic solid surfaces by means of screen printing with different layer thickness on polypropylene film. The obtained analytical dependencies were used to confirm the explanation of the processes that occur during the fabrication of nanophotonic coverings with offset gravure printing plates. As a result of experimental studies, it was determined that the different character of the dependency of total luminescence intensity of nanophotonic elements from the percentage of a pad is explained by the use of different types of offset gravure printing plates, where the size of raster points remains constant in one case and changes in the other case, while the depth of the printing elements accordingly changes or remains constant. To obtain nanophotonic areas with predetermined photoluminescent properties, the influence of investigated factors on changes of photoluminescent properties of nanophotonic printed surfaces should be taken into consideration.

The influence of paint dispersion parameters on the spectral selectivity of black-pigmented coatings

Energy Technology Data Exchange (ETDEWEB)

Gunde, M.K.; Orel, Z.C. [National Institute of Chemistry, Ljubljana (Slovenia); Hutchins, M.G. [Oxford Brookes University, Oxford (United Kingdom). School of Engineering

2003-10-31

The optical properties of variously prepared black-pigmented solar absorbing paints were calculated in terms of their effective absorption and scattering abilities. The phenomenological two-parameter Kubelka-Munk effective medium theory was applied. Paints with the same composition were prepared for different degrees of pigment dispersion and characterized by the average size of pigment agglomerates present in the pigment/vehicle system. Prepared paints were applied to aluminium foil in two ways, by coil coating and by spraying. The size of coarse pigment particles and the paint application technique influence the spectral selectivity and thus determine the final performance of spectrally selective surfaces. (author)

A novel approach to verify the influence of atmospheric parameters in substations concerning lightning

Energy Technology Data Exchange (ETDEWEB)

Souza, Andre Nunes de; Silva, Ivan Nunes da; Ulson, Jose Alfredo C.; Zago, Maria Goretti [UNESP, Bauru, SP (Brazil). Dept. de Engenharia Eletrica]. E-mail: andrejau@bauru.unesp.br

2001-07-01

This paper demonstrates that artificial neural networks can be used effectively for estimation of parameters related to study of atmospheric conditions to high voltage substations design. Specifically, the neural networks are used to compute the variation of electrical field intensity and critical disruptive voltage in substations taking into account several atmospheric factors, such as pressure, temperature, humidity. Examples of simulation of tests are presented to validate the proposed approach. The results that were obtained by experimental evidences and numerical simulations allowed the verification of the influence of the atmospheric conditions on design of substations concerning lightning. (author)

The Influence of the Axial Magnetic Field Upon- the Coaxial Plasma Gun Parameters

International Nuclear Information System (INIS)

El-Aragi, G.M.; El-Demardash, A.

2001-01-01

This study concerns with the influence of an applied axial magnetic field upon the electrical parameters and on the brightness (luminance) of argon plasma. The brightness was measured by with a photomultiplier type of IP28 RCA. The experimental results are investigated with plasma gun device operated with argon gas at a pressure of 3.5 Torr. An axial time independent magnetic field with intensity of 550 G is introduced along the plasma current sheath axial region, within the annular space between the two coaxial electrodes. From the measurements of the discharge current I(t) and the voltage V(t), the electrical discharge parameters of the plasma gun device and the plasma current sheath implosion velocity are estimated, in normal mode of plasma gun operation and in the mode of presence external axial magnetic field. A comparison between these two modes is studied. It was found that the thickness of skin-layer δ about 0.01 cm and the wavelength λ, of the perturbation about 1.3 cm i.e. the instability has been satisfied. The growth rate γ of the instability about 10 6 sec -1 . (author)

Acceleration region influence on beam parameters on stripping foil

International Nuclear Information System (INIS)

Samsonov, E.V.; Tomic, S.

1999-01-01

Some formulas describing the beam parameters on the stripping foil (SF) as a function of the radial amplitude of betatron oscillations and energy gain are derived. The results computed by these formulas are in good agreement with the results of the numerical calculations. Obtained results show that between the radial emittance and the energy spread exists parametric dependence via amplitude of radial betatron oscillations. This conclusion allows one to create a working diagram of expected beam parameters on SF. This diagram may be particularly useful for the extraction system designers since it gives relationship between parameters considered as the extraction system input parameters. (author)

Operational parameters and their influence on particle-side mass transfer resistance in a packed bed bioreactor

OpenAIRE

Hussain, Amir; Kangwa, Martin; Yumnam, Nivedita; Fernandez-Lahore, Marcelo

2015-01-01

The influence of internal mass transfer on productivity as well as the performance of packed bed bioreactor was determined by varying a number of parameters; chitosan coating, flow rate, glucose concentration and particle size. Saccharomyces cerevisiae cells were immobilized in chitosan and non-chitosan coated alginate beads to demonstrate the effect on particle side mass transfer on substrate consumption time, lag phase and ethanol production. The results indicate that chitosan coating, bead...

Influence of Pilot Flame Parameters on the Stability of Turbulent Jet Flames

KAUST Repository

Guiberti, Thibault F.

2016-11-08

This paper presents a comprehensive study of the effects of pilot parameters on flame stability in a turbulent jet flame. The Sydney inhomogeneous piloted burner is employed as the experimental platform with two main fuels, namely, compressed natural gas and liquefied petroleum gas. Various concentrations of five gases are used in the pilot stream, hydrogen, acetylene, oxygen, nitrogen, and argon, to enable a sufficient range in exploring the following parameters: pilot heat release, temperature, burnt gas velocity, equivalence ratio, and H/C ratio. The experimental results are mainly presented in the form of blow-off limits and supported by simple calculations, which simulate various conditions of the pilot–mixture interface. It is found that increasing the pilot adiabatic flame temperature benefits the flame stability and has an even greater influence than the heat release, which is also known to enhance the blow-off limits. Conversely, increasing the pilot burnt gas velocity reduces the blow-off velocity, except for the limiting case when the jet is fully non-premixed. The H/C ratio has negligible effects, while resorting to lean pilots significantly increases the stability of globally rich partially premixed and premixed jets. Such findings are consistent with trends obtained from laminar flame calculations for rich fuel/air mixtures issuing against hot combustion products to simulate the pilot stream.

Determination of reliable force platform parameters and number of trial to evaluate sit-to-stand movement.

Science.gov (United States)

Chorin, Frédéric; Rahmani, Abderrahmane; Beaune, Bruno; Cornu, Christophe

2015-08-01

Sit-to-stand (STS) movement is useful for evaluating lower limb muscle function, especially from force platforms. Nevertheless, due to a lack of standardization of the STS movement (e.g., position, subject's instructions, etc.), it is difficult to compare results obtained in previous studies. The aim of the present study was to determine the most relevant condition, parameters, and number of trial to perform STS movements. In this study, STS mechanical (maximal and mean force, impulse) and temporal parameters were measured in the vertical, medio-lateral and antero-posterior axes using a force platform. Five STS conditions (i.e., with or without armrests, variation of the height of the chair and the movement speed) were analyzed to evaluate repeatability of different standardized procedures. Most of the mechanical and temporal parameters were influenced by the STS condition (p movement.

Kinetic study of the anaerobic biodegradation of alkyl polyglucosides and the influence of their structural parameters.

Science.gov (United States)

Ríos, Francisco; Fernández-Arteaga, Alejandro; Lechuga, Manuela; Jurado, Encarnación; Fernández-Serrano, Mercedes

2016-05-01

This paper reports a study of the anaerobic biodegradation of non-ionic surfactants alkyl polyglucosides applying the method by measurement of the biogas production in digested sludge. Three alkyl polyglucosides with different length alkyl chain and degree of polymerization of the glucose units were tested. The influence of their structural parameters was evaluated, and the characteristics parameters of the anaerobic biodegradation were determined. Results show that alkyl polyglucosides, at the standard initial concentration of 100 mgC L(-1), are not completely biodegradable in anaerobic conditions because they inhibit the biogas production. The alkyl polyglucoside having the shortest alkyl chain showed the fastest biodegradability and reached the higher percentage of final mineralization. The anaerobic process was well adjusted to a pseudo first-order equation using the carbon produced as gas during the test; also, kinetics parameters and a global rate constant for all the involved metabolic process were determined. This modeling is helpful to evaluate the biodegradation or the persistence of alkyl polyglucosides under anaerobic conditions in the environment and in the wastewater treatment.

Influence of radiation-damages on parameters of lattice oscillations in crystalline and vitreous SiO2

International Nuclear Information System (INIS)

Abdukadyrova, I.Kh.

2008-01-01

Using IR reflection spectroscopy, the influence of radiation-induced disturbances on a number of parameters of lattice oscillations in two SiO 2 modifications was investigated. Radiation kinetics of changes in spectral characteristics of fundamental oscillations in SiO 2 crystalline and glassy states was determined. Dose dependences of both reflectivity and degenerate mode vibrational frequency were found to show minima whose locations were governed by a type of a sample. Under higher doses of neutron radiation (10 21 cm -2 ), certain characteristics of bands were observed to be of the same values for the both materials modified. The features of radiation kinetics were found for dynamic parameters of the samples. It was deduced that specific character of radiation-induced changes observed in spectral and dynamic parameters of oscillations in the region of degenerate modes was due to both the accumulation of radiation damages and a change in the force field surrounding bridge-type bonds which was related with the change in the SiO 2 structure. (authors)

DEM modeling of ball mills with experimental validation: influence of contact parameters on charge motion and power draw

Science.gov (United States)

Boemer, Dominik; Ponthot, Jean-Philippe

2017-01-01

Discrete element method simulations of a 1:5-scale laboratory ball mill are presented in this paper to study the influence of the contact parameters on the charge motion and the power draw. The position density limit is introduced as an efficient mathematical tool to describe and to compare the macroscopic charge motion in different scenarios, i.a. with different values of the contact parameters. While the charge motion and the power draw are relatively insensitive to the stiffness and the damping coefficient of the linear spring-slider-damper contact law, the coefficient of friction has a strong influence since it controls the sliding propensity of the charge. Based on the experimental calibration and validation by charge motion photographs and power draw measurements, the descriptive and predictive capabilities of the position density limit and the discrete element method are demonstrated, i.e. the real position of the charge is precisely delimited by the respective position density limit and the power draw can be predicted with an accuracy of about 5 %.

Survey on the parameters influencing X-ray picture quality

International Nuclear Information System (INIS)

Stender, H.S.

1985-01-01

Survey on factors influencing X-ray picture quality: 1) identification of patient and imaged body part. 2) Object properties - thickness, density, built; spatial expansion and arrangement of anatomical parts; object parts in a homogenic and an inhomogenic environment; object movements. 3) Examination technique - matching to medical issue; positioning and adjustment; projection; picture format in keeping with the medical issue; object-related fade-in; distance ratios; contrast medium distribution or deposition; compression. 4) Technical factors of picture production - radiation quality tube voltage; reproducible mAs and mR/mAs; automatic exposure equipment; focal spot size; scattered radiation grid; image intensifier and indirect radiography system; exposure time, dose-to-exposure-time ratio; film-screen combination; cassette with uniform pressure contact; film processing system; radiation safety and light safety. 5) Physical imaging parameters - mean optical density; resolution capacity; contrast reproduction; noise; modulation transmission function. 6) Perceptible picture properties - luminance density; picture contrast; recognizability of details; impression of grain structure; blurred picture structure; visually conspicuous elements. 7) Requirements on picture viewing - viewing device with high luminance density and equalized illumination; possible modification of brilliance; possible fade-in operations and prevention of ambient glare; spot light with iris diaphragm; possible viewing by magnifying lens; selection of correct viewing distances; repeated picture viewing or evaluation by two or more viewers. (orig./HP) [de

Influence of cookies composition on temperature profiles and qualitative parameters during baking

Directory of Open Access Journals (Sweden)

Ž. Kožul

2014-01-01

Full Text Available During baking of bakery products temperature of baking, temperature profiles, moisture content, volume and colour changes are strongly coupled. The objective of this paper was to study the influence of the cookies composition on temperature profiles and quality parameters (width and thickness, colour formation and textural properties: hardness, fracturability and work of breaking force during baking process. Composition of cookies differs due to flour type and initial moisture content. Cookies were baked at 205 °C and temperature was measured in the centre of samples which were 7 mm thick with a 60 mm diameter. The results of temperature profiles of the cookies during baking have shown the same trend for all of the 18 samples. Samples with the higher initial water content have lower values of total colour difference and also significantly affect textural properties.

Study of technological parameters influence on homogeneity of rubber mixings by means of radiotracer methods

International Nuclear Information System (INIS)

Koczorowska, E.

1995-01-01

The radiotracer methods have been worked out for analysis of physico-chemical phenomena. The analysis were carried out for rubber mixings in technological conditions and played a deciding role for quality of manufacturing assortment. The 35 S and 65 Zn have been used as radiotracers. Analysis of different technological parameters influence on behaviour of soluble and polymerized sulfur, zinc compounds as well as other components of the rubber mixing enables to formulate the conclusions important for rubber industry and technology from view point of quality of manufacturing products

Study of the influence of ionizing radiation on biometrical parameters of eggplantand tomato at different doses

International Nuclear Information System (INIS)

Guliyeva, L.M.; Eminova, N.M.; Jafarov, E.S.; Babayev, G.G.

2014-01-01

Full text : The problem of influence of low-dose of ionizing radiation on plants for a long time attracted attention of researchers. Increasing interest in this issue is caused by many circumstances, especially by global radiation contamination of environment. By this time in radiobiology it has been gained great data about the negative effects of ionizing radiation on plants. It is well known that at the time of germination seed is very susceptible to a variety of physical and chemical agents which are capable of impacting their development. It is appropriate to conduct studies reflecting changes in biometrical parameters of agricultural plants importance for Azerbaijan. It was seen that radiation influence increases the productivity of the plants, the size of the stems, fruits, and the color more saturated

Influence of structural parameter included in nonlocal rock mass model on stress concentration around circular tunnel

Science.gov (United States)

Lavrikov, SV; Mikenina, OA; Revuzhenko, AF

2018-03-01

A model of elastic body, including local curvature of elementary volume, is matched with a nonlocal model with a linear structural parameter in the differential approximation. The problem on deformation of rock mass around a circular cross section tunnel is solved numerically. The contours of the calculated stresses are plotted. It is shown that inclusion of local bends in the model results in expansion of influence zone of the tunnel and reduces stress concentration factor at the tunnel boundary.

Influence of the operating parameters on the flux during microfiltration of the steepwater in the starch industry

Directory of Open Access Journals (Sweden)

Šereš Zita I.

2012-01-01

Full Text Available The subject of the work is the possibility of applying microfiltration through a ceramic tubular membrane with 100 nm pore sizes to the steepwater obtained in the production process of corn starch. The dry matter content should be reduced in the steepwater permeate. Thus the consumption of the process water would be reduced, the nutrients from the steepwater could be exploited as feed and the wastewater problem would consequently be solved. The objective of the work was to examine the influence of the operating parameters on the permeate flux during steepwater microfiltration. The parameters that vary in the course of microfiltration, were the transmembrane pressur and flow rate, while the permeate flux and dry matter content of the permeate and retentate were the dependent parameters, constantly monitored during the process. Another objective of this study was to investigate the influence of static turbulence promoter on the permeate flux during steepwater microfiltration. Static mixers enhance permeate flux, thus the microfiltration can be performed longer. As a result of the statistical analysis, the optimal conditions for steepwater microfiltration were determined. The maximum value of the permeate flux without mixer (25 lm-2h-1 was achieved at a pressure of 2 bars and a flow rate around 100 lh-1. With the use of static mixer the flux is 2,5 times higher compared to the one obtained without the mixer. The dry matter content of the permeat after 2.5 hours of mucrofiltration was lowered by 40%.

Musculoskeletal simulations to investigate the influence of vertebral geometrical parameters on lumbar spine loading

DEFF Research Database (Denmark)

Putzer, Michael; Rasmussen, John; Penzkofer, Rainer

Body Modeling System and a parameterized musculoskeletal lumbar spine model for four different postures: upright standing, flexion (50°), torsion (10°) and lateral bending (15°). The linear dimensions of the vertebral body, the posterior parts of the vertebrae as well as the disc height, the orientation...... of the facet joints and the curvature of the lumbar spine have been varied. Figure 1 depicts the used musculoskeletal model in the flexed posture and a lumbar vertebra labeled with all relevant linear dimensions except the disc height. Additionally, all combinations of the three parameters vertebral body...... are consistent with the corresponding results of Han et al. (2012) and Niemeyer et al. (2012). As mentioned above, the vertebral body depth showed a recognizable effect for the flexed and lateral bended postures, too. These characteristics can be justified with increasing moments due to the changed offset...

Influence of initial lung deposit on absorption parameters of Pu and am: application to (U, Pu)O2 powder after inhalation in the baboon

International Nuclear Information System (INIS)

Rateau-matton, S.R.M.; Abram, M.C.; Rouit, E.; Grillon, G.; Legall, B.L.G.; Van Der Meeren, A.V.D.

2006-01-01

Full text of publication follows: In cases of contamination by inhalation, risk assessment would be performed taking into account recommendations of the International Commission of Radiological Protection (ICRP) Human Respiratory Tract Model (H.R.T.M.) described in Publication 66 (ICRP 66, 1994). The use of absorption parameter values specific to each component is recommended when available for dose calculation in order to provide a more realistic assessment of risk. The solubility of Pu and Am deposited in the respiratory tract after inhalation is a relevant parameter that can aid the identification of target organs. The aim of this study is to show the influence of the initial lung deposit (I.L.D.) on absorption parameters after inhalation of Mixed oxides (Mox) powder (7.14 % Pu w/w) in baboons. Daily urinary excretion of Pu/Am was measured for 3 months which allowed the estimation of the removal of the soluble fraction from lungs to blood and in particular a proportion of absorption parameters. Urinary excretion on 3 -month period were represented by biphasic curves which were directly reliable to physicochemical properties of compounds. Males baboon were exposed to I.L.D.: 40 to 860 kBq. Results obtained show that urinary excretions progress in the reverse order of I.L.D. Moreover, significant differences in the behaviour of Pu and Am were also observed in the target organs (liver and skeleton) and especially Am was more soluble than Pu for the compound studied. So, hypothesis of a more important dissolution of Am compare to Pu combines to a special affinity of Am for target organs seem to be involve. This result was very important in case of dismantling operation mainly in the usury of fuel since 241 Am is a filiation product of 241 Pu. In conclusion, this work contributes to support the usefulness of experimental data in radioprotection to estimate level of radiological exposition of worker. (authors)

Influences of the Ratio of Polyol and MDI on the Acoustic Parameters of Polyurethane

Science.gov (United States)

Wang, Yonghua; Liu, Zheming; Wu, Haiquan; Zhang, Chengchun; Yu, Huadong; Ren, Luquan; Ichchou, Mohamed

2018-05-01

In this paper, the influence of different ratio of polyol and MDI on the absorption coefficient and acoustic parameters of polyurethane was studied. Ratio of 100:40 and 100:45 show the best sound absorption performance, and the change trend of transmission loss and sound absorption coefficient are opposite. The flow resistance increased with the increasing of the ratio of polyol and MDI, the greater the flow resistance, the worse the high frequency sound absorption property of the polyurethane. When the ratio of polyol and MDI keep 100:45, the minimum porosity of sample, the polyurethane porosity increase with the ratio of polyol and MDI increase.

Influence of cutting data on surface quality when machining 17-4 PH stainless steel

Science.gov (United States)

Popovici, T. D.; Dijmărescu, M. R.

2017-08-01

The aim of the research presented in this paper is to analyse the cutting data influence upon surface quality for 17-4 PH stainless steel milling machining. The cutting regime parameters considered for the experiments were established using cutting regimes from experimental researches or from industrial conditions as basis, within the recommended ranges. The experimental program structure was determined by taking into account compatibility and orthogonality conditions, minimal use of material and labour. The machined surface roughness was determined by measuring the Ra roughness parameter, followed by surface profile registration in the form of graphics which were saved on a computer with MarSurf PS1Explorer software. Based on Ra roughness parameter, maximum values were extracted from these graphics and the influence charts of the cutting regime parameters upon surface roughness were traced using Microsoft Excel software. After a thorough analysis of the resulting data, relevant conclusions were drawn, presenting the interdependence between the surface roughness of the machined 17-4 PH samples and the cutting data variation.

Establishing principal soil quality parameters influencing earthworms in urban soils using bioassays

International Nuclear Information System (INIS)

Hankard, Peter K.; Bundy, Jacob G.; Spurgeon, David J.; Weeks, Jason M.; Wright, Julian; Weinberg, Claire; Svendsen, Claus

2005-01-01

Potential contamination at ex-industrial sites means that, prior to change of use, it will be necessary to quantify the extent of risks to potential receptors. To assess ecological hazards, it is often suggested to use biological assessment to augment chemical analyses. Here we investigate the potential of a commonly recommended bioassay, the earthworm reproduction test, to assess the status of urban contaminated soils. Sample points at all study sites had contaminant concentrations above the Dutch soil criteria Target Values. In some cases, the relevant Intervention Values were exceeded. Earthworm survival at most points was high, but reproduction differed significantly in soil from separate patches on the same site. When the interrelationships between soil parameters and reproduction were studied, it was not possible to create a good model of site soil toxicity based on single or even multiple chemical measurements of the soils. We thus conclude that chemical analysis alone is not sufficient to characterize soil quality and confirms the value of biological assays for risk assessment of potentially contaminated soils. - Bioassays must be applied for the risk assessment complexly-polluted sites to complement chemical analysis of soils

Orbital parameters of extrasolar planets derived from polarimetry

Science.gov (United States)

Fluri, D. M.; Berdyugina, S. V.

2010-03-01

Context. Polarimetry of extrasolar planets becomes a new tool for their investigation, which requires the development of diagnostic techniques and parameter case studies. Aims: Our goal is to develop a theoretical model which can be applied to interpret polarimetric observations of extrasolar planets. Here we present a theoretical parameter study that shows the influence of the various involved parameters on the polarization curves. Furthermore, we investigate the robustness of the fitting procedure. We focus on the diagnostics of orbital parameters and the estimation of the scattering radius of the planet. Methods: We employ the physics of Rayleigh scattering to obtain polarization curves of an unresolved extrasolar planet. Calculations are made for two cases: (i) assuming an angular distribution for the intensity of the scattered light as from a Lambert sphere and for polarization as from a Rayleigh-type scatterer; and (ii) assuming that both the intensity and polarization of the scattered light are distributed according to the Rayleigh law. We show that the difference between these two cases is negligible for the shapes of the polarization curves. In addition, we take the size of the host star into account, which is relevant for hot Jupiters orbiting giant stars. Results: We discuss the influence of the inclination of the planetary orbit, the position angle of the ascending node, and the eccentricity on the linearly polarized light curves both in Stokes Q/I and U/I. We also analyze errors that arise from the assumption of a point-like star in numerical modeling of polarization as compared to consistent calculations accounting for the finite size of the host star. We find that errors due to the point-like star approximation are reduced with the size of the orbit, but still amount to about 5% for known hot Jupiters. Recovering orbital parameters from simulated data is shown to be very robust even for very noisy data because the polarization curves react

The influence on the contact condition and initial fixation stability of the main design parameters of a self-expansion type anterior cruciate ligament fixation device

International Nuclear Information System (INIS)

Kim, Jong Dae; Oh, Chae Youn; Kim, Cheol Sang

2008-01-01

This paper proposes a self-expansion type anterior cruciate ligament fixation device. The proposed fixation device provides graft fixation force by maintaining contact with the bone tunnel. Since the device maintains contact with the bone tunnel by the force that expands by the self-driven elastic force of the device, the main design parameters that determine the performance of this device are the ring thickness and expansion angle. This paper develops the three-dimensional finite element models of the fixation device and bone. By simulation with the developed finite element model, this paper studies the influence of the main design parameters of the device on the maximum stress around the ring when grasping the fixation device. Through the analysis of the stress on the bone tunnel wall when the fixation device comes in contact with the bone tunnel, this paper shows the influence of the main design parameters of the fixation device on the contact condition. In addition, through the analysis of the migration that occur upon application of the pull-out force, this paper studies the influence of the main design parameters on the initial fixation stability of the fixation device

The influence on the contact condition and initial fixation stability of the main design parameters of a self-expansion type anterior cruciate ligament fixation device

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong Dae [Jeonju University, Jeonju (Korea, Republic of); Oh, Chae Youn; Kim, Cheol Sang [Chonbuk National University, Jeonju (Korea, Republic of)

2008-12-15

This paper proposes a self-expansion type anterior cruciate ligament fixation device. The proposed fixation device provides graft fixation force by maintaining contact with the bone tunnel. Since the device maintains contact with the bone tunnel by the force that expands by the self-driven elastic force of the device, the main design parameters that determine the performance of this device are the ring thickness and expansion angle. This paper develops the three-dimensional finite element models of the fixation device and bone. By simulation with the developed finite element model, this paper studies the influence of the main design parameters of the device on the maximum stress around the ring when grasping the fixation device. Through the analysis of the stress on the bone tunnel wall when the fixation device comes in contact with the bone tunnel, this paper shows the influence of the main design parameters of the fixation device on the contact condition. In addition, through the analysis of the migration that occur upon application of the pull-out force, this paper studies the influence of the main design parameters on the initial fixation stability of the fixation device

Influence of autoclave sterilization on the surface parameters and mechanical properties of six orthodontic wires.

Science.gov (United States)

Pernier, C; Grosgogeat, B; Ponsonnet, L; Benay, G; Lissac, M

2005-02-01

Orthodontic wires are frequently packaged in individual sealed bags in order to avoid cross-contamination. The instructions on the wrapper generally advise autoclave sterilization of the package and its contents if additional protection is desired. However, sterilization can modify the surface parameters and the mechanical properties of many types of material. The aim of this research was to determine the influence of one of the most widely used sterilization processes, autoclaving (18 minutes at 134 degrees C, as recommended by the French Ministry of Health), on the surface parameters and mechanical properties of six wires currently used in orthodontics (one stainless steel alloy: Tru-Chrome RMO; two nickel-titanium shape memory alloys: Neo Sentalloy and Neo Sentalloy with Ionguard GAC; and three titanium-molybdenum alloys: TMA(R) and Low Friction TMA Ormco and Resolve GAC). The alloys were analysed on receipt and after sterilization, using surface structure observation techniques, including optical, scanning electron and atomic force microscopy and profilometry. The mechanical properties were assessed by three-point bending tests. The results showed that autoclave sterilization had no adverse effects on the surface parameters or on the selected mechanical properties. This supports the possibility for practitioners to systematically sterilize wires before placing them in the oral environment.

An Influence of 7.5 T Superconducting Wiggler on Beam Parameters of Siberia-2 Storage Ring

International Nuclear Information System (INIS)

Korchuganov, Vladimir; Valentinov, Alexander; Mezentsev, Nikolai

2007-01-01

At present the dedicated synchrotron radiation source Siberia-2 in Kurchatov Institute operates with electron energy 2.5 GeV and current up to 200 mA. In order to expand spectral range of SR and to increase brightness an installation of 7.5 T 19-pole superconducting wiggler is planned at the end of 2006. Now the wiggler is under fabrication in BINP, Novosibirsk. Such high level of a magnetic field in the wiggler will have a great influence on electron beam parameters of Siberia-2. Changes of these parameters (betatron tunes, horizontal emittance of the electron beam, momentum compaction, energy spread etc.) are discussed in the report. Different methods of compensation (global and local) of betatron functions distortion are presented. Much attention is paid to dynamic aperture calculations using analytical approximation of magnetic field behavior in transverse horizontal direction

Influence of Nd dopants on lattice parameters and thermal and elastic properties in YVO4 single crystals

International Nuclear Information System (INIS)

Kucytowski, J.; Wokulska, K.; Kazmierczak-Balata, A.; Bodzenta, J.; Lukasiewicz, T.; Hofman, B.; Pyka, M.

2008-01-01

The influence of neodymium doping on YVO 4 single crystals has been studied. The crystals were grown by the Czochralski method. One of them was pure YVO 4 and the others were doped with neodymium (YVO 4 :Nd) at various concentrations of Nd = 0.3-3.0 at.%. The changes of the lattice parameters were determined by the Bond's method [W.L. Bond, Acta Cryst. 13 (1960) 814]. The thermal diffusivity and the velocity of ultrasound using the photothermal method with mirage effect and the pulse echo method [J. Bodzenta, M. Pyka, J. Phys. IV France 137 (2006) 259] were measured. In the examined crystals, it was found that the lattice parameters increase while the thermal diffusivity decreases with increasing concentration of Nd atoms

Qualitative Parameters of Practice during University Studies

Science.gov (United States)

Stasiunaitiene, Egle; Norkute, Odeta

2011-01-01

In this article, relevance of practice during university studies is highlighted, as well as the main stages of its organisation, qualitative parameters, as well as criteria and indicators that validate them are defined. Discussion on the idea that taking into consideration qualitative parameters of organising practice as a component of studies…

Water and Oil Repellent Finishing of Textiles by UV Curing: Evaluation of the Influence of Scaled-Up Process Parameters

Directory of Open Access Journals (Sweden)

Franco Ferrero

2017-04-01

Full Text Available In this work, various textile fabrics were coated with silicone and fluorocarbon-based resins by photo-curing using ultraviolet irradiation. A great number of large fabric samples were impregnated by padding with commercial finishing agents and then irradiated in air with a high power, semi-industrial UV source. The add-on of various finishing agents was kept low to reduce the treatment cost. White and dyed samples of different textile composition were treated and evaluated in terms of conferred repellency, yellowing, or color changes. Most relevant process parameters were investigated, utilizing the thermal process normally adopted at industrial level as reference. The results were statistically evaluated by ANOVA using Minitab 16 software, in order to identify the most influential parameters and to evaluate the real possibility of replacing the thermal treatment with UV curing.

Seasonal influence on the hematological parameters in cultured Nile tilapia from southern Brazil

Directory of Open Access Journals (Sweden)

GT. Jerônimo

Full Text Available This study evaluated seasonality in hematological parameters of Nile tilapia cultured in the state of Santa Catarina, southern Brazil. A total of 240 fish were examined during four seasons between April 2007 and March 2008 in three different fish farms. After being anesthetised in a benzocaine solution, blood samples were withdrawn into syringes containing a drop of 10% EDTA for hematological analysis. The results were compared between fish farms and seasons, which are well delimited in southern Brazil. In a traditional fish farm in Joinville in the summer, there was an increase in the percentage of hematocrit and in the red blood cell count. The highest values of total leukocytes were found in fish from fee-fishing in Blumenau in the autumn while the lowest values occurred in those from swine consorted system in Ituporanga in the summer. Thrombocytosis was observed in the autumn, and lymphocytosis was found in both the autumn and winter in tilapia from all fish farms investigated. Neutrophilia was only observed in winter and autumn in fish from Blumenau and Ituporanga. This work demonstrated the influence of seasonality and the handling characteristics of each fish farm on certain hematological parameters in Nile tilapia.

Why relevance theory is relevant for lexicography

DEFF Research Database (Denmark)

Bothma, Theo; Tarp, Sven

2014-01-01

This article starts by providing a brief summary of relevance theory in information science in relation to the function theory of lexicography, explaining the different types of relevance, viz. objective system relevance and the subjective types of relevance, i.e. topical, cognitive, situational...... that is very important for lexicography as well as for information science, viz. functional relevance. Since all lexicographic work is ultimately aimed at satisfying users’ information needs, the article then discusses why the lexicographer should take note of all these types of relevance when planning a new...... dictionary project, identifying new tasks and responsibilities of the modern lexicographer. The article furthermore discusses how relevance theory impacts on teaching dictionary culture and reference skills. By integrating insights from lexicography and information science, the article contributes to new...

Development of response inhibition in the context of relevant versus irrelevant emotions

Directory of Open Access Journals (Sweden)

Margot A Schel

2013-07-01

Full Text Available The present study examined the influence of relevant and irrelevant emotions on response inhibition from childhood to early adulthood. Ninety-four participants between 6 and 25 years of age performed two go/nogo tasks with emotional faces (neutral, happy, and fearful as stimuli. In one go/nogo task emotion formed a relevant dimension of the task and in the other go/nogo task emotion was irrelevant and participants had to respond to the color of the faces instead. A special feature of the latter task, in which emotion was irrelevant, was the inclusion of free choice trials, in which participants could freely decide between acting and inhibiting. Results showed a linear increase in response inhibition performance with increasing age both in relevant and irrelevant affective contexts. Relevant emotions had a pronounced influence on performance across age, whereas irrelevant emotions did not. Overall, participants made more false alarms on trials with fearful faces than happy faces, and happy faces were associated with better performance on go trials (higher percentage correct and faster RTs than fearful faces. The latter effect was stronger for young children in terms of accuracy. Finally, during the free choice trials participants did not base their decisions on affective context, confirming that irrelevant emotions do not have a strong impact on inhibition. Together, these findings suggest that across development relevant affective context has a larger influence on response inhibition than irrelevant affective context. When emotions are relevant, a context of positive emotions is associated with better performance compared to a context with negative emotions, especially in young children.

The influence of spray-drying parameters on phase behavior, drug distribution, and in vitro release of injectable microspheres for sustained release.

Science.gov (United States)

Meeus, Joke; Lenaerts, Maité; Scurr, David J; Amssoms, Katie; Davies, Martyn C; Roberts, Clive J; Van Den Mooter, Guy

2015-04-01

For ternary solid dispersions, it is indispensable to characterize their structure, phase behavior, and the spatial distribution of the dispersed drug as this might influence the release profile and/or stability of these formulations. This study shows how formulation (feed concentration) and process (feed rate, inlet air temperature, and atomizing air pressure) parameters can influence the characteristics of ternary spray-dried solid dispersions. The microspheres considered here consist of a poly(lactic-co-glycolic acid) (PLGA) surface layer and an underlying polyvinylpyrrolidone (PVP) phase. A poorly soluble active pharmaceutical ingredient (API) was molecularly dispersed in this matrix. Differences were observed in component miscibility, phase heterogeneity, particle size, morphology, as well as API surface coverage for selected spray-drying parameters. Observed differences are likely because of changes in the droplet generation, evaporation, and thus particle formation processes. However, varying particle characteristics did not influence the drug release of the formulations studied, indicating the robustness of this approach to produce particles of consistent drug release characteristics. This is likely because of the fact that the release is dominated by diffusion from the PVP layer through pores in the PLGA surface layer and that observed differences in the latter have no influence on the release. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Estimating the relevance of world disturbances to explain savings, interference and long-term motor adaptation effects.

Directory of Open Access Journals (Sweden)

Max Berniker

2011-10-01

Full Text Available Recent studies suggest that motor adaptation is the result of multiple, perhaps linear processes each with distinct time scales. While these models are consistent with some motor phenomena, they can neither explain the relatively fast re-adaptation after a long washout period, nor savings on a subsequent day. Here we examined if these effects can be explained if we assume that the CNS stores and retrieves movement parameters based on their possible relevance. We formalize this idea with a model that infers not only the sources of potential motor errors, but also their relevance to the current motor circumstances. In our model adaptation is the process of re-estimating parameters that represent the body and the world. The likelihood of a world parameter being relevant is then based on the mismatch between an observed movement and that predicted when not compensating for the estimated world disturbance. As such, adapting to large motor errors in a laboratory setting should alert subjects that disturbances are being imposed on them, even after motor performance has returned to baseline. Estimates of this external disturbance should be relevant both now and in future laboratory settings. Estimated properties of our bodies on the other hand should always be relevant. Our model demonstrates savings, interference, spontaneous rebound and differences between adaptation to sudden and gradual disturbances. We suggest that many issues concerning savings and interference can be understood when adaptation is conditioned on the relevance of parameters.

Influence of technical parameters on epicardial fat volume quantification at cardiac CT

International Nuclear Information System (INIS)

Bucher, Andreas M.; Joseph Schoepf, U.; Krazinski, Aleksander W.; Silverman, Justin; Spearman, James V.; De Cecco, Carlo N.; Meinel, Felix G.; Vogl, Thomas J.; Geyer, Lucas L.

2015-01-01

Highlights: • Upper threshold levels and contrast enhancement influence epicardial fat volumetry. • Cardiac cycle does not significantly influence epicardial fat volumetry. • Adjustments of upper threshold can lead to comparable volumetry results. - Abstract: Objectives: To systematically analyze the influence of technical parameters on quantification of epicardial fat volume (EATV) at cardiac CT. Methods: 153 routine cardiac CT data sets were analyzed using three-dimensional pericardial border delineation. Three image series were reconstructed per patient: (a) CTA D : coronary CT angiography (CTA), diastolic phase; (b) CTA S : coronary CTA, systolic phase; (c) CaSc D : non-contrast CT, diastolic phase. EATV was calculated using three different upper thresholds (−15HU, −30HU, −45HU). Repeated measures ANOVA, Spearman's rho, and Bland Altman plots were used. Results: Mean EATV differed between all three image series at a −30HU threshold (CTA D 87.2 ± 38.5 ml, CTA S 90.9 ± 37.7 ml, CaSc D 130.7 ± 49.5 ml, P < 0.001). EATV of diastolic and systolic CTA reconstructions did not differ significantly (P = 0.225). Mean EATV for contrast enhanced CTA at a −15HU threshold (CTA D15 102.4 ± 43.6 ml, CTA S15 105.3 ± 42.3 ml) could be approximated most closely by non-contrast CT at −45HU threshold (CaSc D45 105.3 ± 40.8 ml). The correlation was excellent: CTA S15 –CTA D15 , rho = 0.943; CTA D15 –CaSc D45 , rho = 0.905; CTA S15 –CaSc D45 , rho = 0.924; each P < 0.001). Bias values from Bland Altman Analysis were: CTA S15 –CTA D15 , 4.9%; CTA D15 –CaSc D45 , −4.3%; CTA S15 –CaSc D45 , 0.6%. Conclusions: Measured EATV can differ substantially between contrast enhanced and non-contrast CT studies, which can be reconciled by threshold modification. Heart cycle phase does not significantly influence EATV measurements

Influence of technical parameters on epicardial fat volume quantification at cardiac CT

Energy Technology Data Exchange (ETDEWEB)

Bucher, Andreas M. [Department of Radiology and Radiological Science, Medical University of South Carolina, Charleston, SC (United States); Department of Diagnostic and Interventional Radiology, Clinic of the Goethe University, Frankfurt (Germany); Joseph Schoepf, U., E-mail: schoepf@musc.edu [Department of Radiology and Radiological Science, Medical University of South Carolina, Charleston, SC (United States); Division of Cardiology, Department of Medicine, Medical University of South Carolina, Charleston, SC (United States); Krazinski, Aleksander W.; Silverman, Justin; Spearman, James V. [Department of Radiology and Radiological Science, Medical University of South Carolina, Charleston, SC (United States); De Cecco, Carlo N. [Department of Radiology and Radiological Science, Medical University of South Carolina, Charleston, SC (United States); Department of Radiological Sciences, Oncology and Pathology, University of Rome “Sapienza” – Polo Pontino, Latina (Italy); Meinel, Felix G. [Department of Radiology and Radiological Science, Medical University of South Carolina, Charleston, SC (United States); Institute for Clinical Radiology, Ludwig-Maximilians-University Hospital, Munich (Germany); Vogl, Thomas J. [Department of Diagnostic and Interventional Radiology, Clinic of the Goethe University, Frankfurt (Germany); Geyer, Lucas L. [Department of Radiology and Radiological Science, Medical University of South Carolina, Charleston, SC (United States); Institute for Clinical Radiology, Ludwig-Maximilians-University Hospital, Munich (Germany)

2015-06-15

Highlights: • Upper threshold levels and contrast enhancement influence epicardial fat volumetry. • Cardiac cycle does not significantly influence epicardial fat volumetry. • Adjustments of upper threshold can lead to comparable volumetry results. - Abstract: Objectives: To systematically analyze the influence of technical parameters on quantification of epicardial fat volume (EATV) at cardiac CT. Methods: 153 routine cardiac CT data sets were analyzed using three-dimensional pericardial border delineation. Three image series were reconstructed per patient: (a) CTA{sub D}: coronary CT angiography (CTA), diastolic phase; (b) CTA{sub S}: coronary CTA, systolic phase; (c) CaSc{sub D}: non-contrast CT, diastolic phase. EATV was calculated using three different upper thresholds (−15HU, −30HU, −45HU). Repeated measures ANOVA, Spearman's rho, and Bland Altman plots were used. Results: Mean EATV differed between all three image series at a −30HU threshold (CTA{sub D} 87.2 ± 38.5 ml, CTA{sub S} 90.9 ± 37.7 ml, CaSc{sub D} 130.7 ± 49.5 ml, P < 0.001). EATV of diastolic and systolic CTA reconstructions did not differ significantly (P = 0.225). Mean EATV for contrast enhanced CTA at a −15HU threshold (CTA{sub D15} 102.4 ± 43.6 ml, CTA{sub S15} 105.3 ± 42.3 ml) could be approximated most closely by non-contrast CT at −45HU threshold (CaSc{sub D45} 105.3 ± 40.8 ml). The correlation was excellent: CTA{sub S15}–CTA{sub D15}, rho = 0.943; CTA{sub D15}–CaSc{sub D45}, rho = 0.905; CTA{sub S15}–CaSc{sub D45}, rho = 0.924; each P < 0.001). Bias values from Bland Altman Analysis were: CTA{sub S15}–CTA{sub D15}, 4.9%; CTA{sub D15}–CaSc{sub D45}, −4.3%; CTA{sub S15}–CaSc{sub D45}, 0.6%. Conclusions: Measured EATV can differ substantially between contrast enhanced and non-contrast CT studies, which can be reconciled by threshold modification. Heart cycle phase does not significantly influence EATV measurements.

Influence of the solid-gas interface on the effective thermal parameters of a two-layer structure in photoacoustic experiments

International Nuclear Information System (INIS)

Aguirre, N Munoz; Perez, L MartInez; Garibay-Febles, V; Lozada-Cassou, M

2004-01-01

From the theoretical point of view, the influence of the solid-gas interface on the effective thermal parameters in a two-layer structure of the photoacoustic technique is discussed. It is shown that the effective thermal parameters depend strongly upon the thermal resistance value associated with the solid-gas interface. New expressions for the effective thermal conductivity and thermal diffusivity in the low frequency limit are obtained. In the high frequency limit, the 'resonant' behaviour of the effective thermal diffusivity is maintained and a new complex dependence on frequency of the effective thermal conductivity is shown

Influence of Parameters of a Printing Plate on Photoluminescence of Nano photonic Printed Elements of Novel Packaging

International Nuclear Information System (INIS)

Sarapulova, O.; Sherstiuk, V.

2015-01-01

In order to produce nano photonic elements for smart packaging, we investigated the influence of the parameters of screen and offset gravure printing plates on features of printed application of coatings with nano photonic components and on parameters of their photoluminescence. To determine the dependence of luminescence intensity on the thickness of solid coating, we carried out the formation of nano photonic solid surfaces by means of screen printing with different layer thickness on polypropylene film. The obtained analytical dependencies were used to confirm the explanation of the processes that occur during the fabrication of nano photonic coverings with offset gravure printing plates. As a result of experimental studies, it was determined that the different character of the dependency of total luminescence intensity of nano photonic elements from the percentage of a pad is explained by the use of different types of offset gravure printing plates, where the size of raster points remains constant in one case and changes in the other case, while the depth of the printing elements accordingly changes or remains constant. To obtain nano photonic areas with predetermined photo luminescent properties, the influence of investigated factors on changes of photo luminescent properties of nano photonic printed surfaces should be taken into consideration

Formulation parameters influencing self-stratification of coatings

NARCIS (Netherlands)

Vink, P.; Bots, T.L.

1996-01-01

Research was carried out aimed at the development of self-stratifying paints for steel which after application during film formation spontaneously form two well established layers of primer and top coat. The parameters affecting stratification were investigated for combinations of epoxy resins and

The influence of common stimulus parameters on distortion product otoacoustic emission fine structure.

Science.gov (United States)

Johnson, Tiffany A; Baranowski, Lauren G

2012-01-01

To determine whether common approaches to setting stimulus parameters influence the depth of fine structure present in the distortion product otoacoustic emission (DPOAE) response. Because the presence of fine structure has been suggested as a possible source of errors, if one of the common parametric approaches results in reduced fine-structure depth, it may be preferred over other approaches. DPOAE responses were recorded in a group of 21 subjects with normal hearing for 1/3-octave intervals surrounding 3 f2s (1, 2, and 4 kHz) at three L2s (30, 45, and 55 dB SPL). For each f2 and L2 combination, L1 and f2/f1 were set according to three commonly used parametric approaches. These included a simple approach, the approach recommended by Kummer et al., and the approach described by Johnson et al. These three approaches primarily differ in the recommended relationship between L1 and L2. For each parametric approach, DPOAE fine structure was evaluated by varying f2 in small steps. Differences in DPOAE level and DPOAE fine-structure depth across f2, L2, and the various stimulus parameters were evaluated using repeated-measures analysis of variance. As expected, significant variations in DPOAE level were observed across the three parametric approaches. For stimulus levels #45 dB SPL, the simple stimuli resulted in lower DPOAE levels than were observed for other approaches. An unexpected finding was that stimulus parameters developed by Johnson et al., which were believed to produce higher DPOAE levels than other approaches, produced the lowest DPOAE levels of the three approaches when f2 = 4 kHz. Significant differences in fine-structure depth were also observed. Greater fine-structure depth was observed with the simple parameters, although this effect was restricted to L2 # 45 dB SPL. When L2 = 55 dB SPL, all three parametric approaches resulted in equivalent fine-structure depth. A significant difference in fine-structure depth across the 3 f2s was also observed. The

Influence of Different Container Closure Systems and Capping Process Parameters on Product Quality and Container Closure Integrity (CCI) in GMP Drug Product Manufacturing.

Science.gov (United States)

Mathaes, Roman; Mahler, Hanns-Christian; Roggo, Yves; Huwyler, Joerg; Eder, Juergen; Fritsch, Kamila; Posset, Tobias; Mohl, Silke; Streubel, Alexander

2016-01-01

Capping equipment used in good manufacturing practice manufacturing features different designs and a variety of adjustable process parameters. The overall capping result is a complex interplay of the different capping process parameters and is insufficiently described in literature. It remains poorly studied how the different capping equipment designs and capping equipment process parameters (e.g., pre-compression force, capping plate height, turntable rotating speed) contribute to the final residual seal force of a sealed container closure system and its relation to container closure integrity and other drug product quality parameters. Stopper compression measured by computer tomography correlated to residual seal force measurements.In our studies, we used different container closure system configurations from different good manufacturing practice drug product fill & finish facilities to investigate the influence of differences in primary packaging, that is, vial size and rubber stopper design on the capping process and the capped drug product. In addition, we compared two large-scale good manufacturing practice manufacturing capping equipment and different capping equipment settings and their impact on product quality and integrity, as determined by residual seal force.The capping plate to plunger distance had a major influence on the obtained residual seal force values of a sealed vial, whereas the capping pre-compression force and the turntable rotation speed showed only a minor influence on the residual seal force of a sealed vial. Capping process parameters could not easily be transferred from capping equipment of different manufacturers. However, the residual seal force tester did provide a valuable tool to compare capping performance of different capping equipment. No vial showed any leakage greater than 10(-8)mbar L/s as measured by a helium mass spectrometry system, suggesting that container closure integrity was warranted in the residual seal force range

Computer modelling system of the chemical composition and treatment parameters influence on mechanical properties of structural steels

OpenAIRE

L.A. Dobrzański; R. Honysz

2009-01-01

Purpose: This paper presents Neuro-Lab. It is an authorship programme, which use algorithms of artificial intelligence for structural steels mechanical properties estimation.Design/methodology/approach: On the basis of chemical composition, parameters of heat and mechanical treatment and elements of geometrical shape and size this programme has the ability to calculate the mechanical properties of examined steel and introduce them as raw numeric data or in graphic as influence charts. Possibl...

Influence of anodization parameters on the morphology of TiO 2 nanotube arrays

Science.gov (United States)

Omidvar, Hamid; Goodarzi, Saba; Seif, Ahmad; Azadmehr, Amir R.

2011-07-01

TiO 2 nanotube arrays can be fabricated by electrochemical anodization in organic and inorganic electrolytes. Morphology of these nanotube arrays changes when anodization parameters such as applied voltage, type of electrolyte, time and temperature are varied. Nanotube arrays fabricated by anodization of commercial titanium in electrolytes containing NH 4F solution and either sulfuric or phosphoric acid were studied at room temperature; time of anodization was kept constant. Applied voltage, fluoride ion concentration, and acid concentrations were varied and their influences on TiO 2 nanotubes were investigated. The current density of anodizing was recorded by computer controlled digital multimeter. The surface morphology (top-view) of nanotube arrays were observed by SEM. The nanotube arrays in this study have inner diameters in range of 40-80 nm.

The Relevant Physical Trace in Criminal Investigation

Directory of Open Access Journals (Sweden)

Durdica Hazard

2016-01-01

Full Text Available A criminal investigation requires the forensic scientist to search and to interpret vestiges of a criminal act that happened in the past. The forensic scientist is one of the many stakeholders who take part in the information quest within the criminal justice system. She reads the investigation scene in search of physical traces that should enable her to tell the story of the offense/crime that allegedly occurred. The challenge for any investigator is to detect and recognize relevant physical traces in order to provide clues for investigation and intelligence purposes, and that will constitute sound and relevant evidence for the court. This article shows how important it is to consider the relevancy of physical traces from the beginning of the investigation and what might influence the evaluation process. The exchange and management of information between the investigation stakeholders are important. Relevancy is a dimension that needs to be understood from the standpoints of law enforcement personnel and forensic scientists with the aim of strengthening investigation and ultimately the overall judicial process.

Task relevance differentially shapes ventral visual stream sensitivity to visible and invisible faces

DEFF Research Database (Denmark)

Kouider, Sid; Barbot, Antoine; Madsen, Kristoffer Hougaard

2016-01-01

requires dissociating it from the top-down influences underlying conscious recognition. Here, using visual masking to abolish perceptual consciousness in humans, we report that functional magnetic resonance imaging (fMRI) responses to invisible faces in the fusiform gyrus are enhanced when they are task...... relevance crucially shapes the sensitivity of fusiform regions to face stimuli, leading from enhancement to suppression of neural activity when the top-down influences accruing from conscious recognition are prevented.......Top-down modulations of the visual cortex can be driven by task relevance. Yet, several accounts propose that the perceptual inferences underlying conscious recognition involve similar top-down modulations of sensory responses. Studying the pure impact of task relevance on sensory responses...

Estimation and Statistical Analysis of Human Voice Parameters to Investigate the Influence of Psychological Stress and to Determine the Vocal Tract Transfer Function of an Individual

OpenAIRE

Mongia, Puneet Kumar; Sharma, R. K.

2014-01-01

In this study the principal focus is to examine the influence of psychological stress (both positive and negative stress) on the human articulation and to determine the vocal tract transfer function of an individual using inverse filtering technique. Both of these analyses are carried out by estimating various voice parameters. The outcomes of the analysis of psychological stress indicate that all the voice parameters are affected due to the influence of stress on humans. About 35 out of 51 p...

Effect of relevant culture parameters on Pertussis toxin expression by Bordetella pertussis

NARCIS (Netherlands)

Thalen, M.; Venema, M.; IJssel, van den J.; Berwald, L.; Beuvery, E.C.; Martens, D.E.; Tramper, J.

2006-01-01

Whooping cough vaccines are produced using different ranges of cultivation conditions and medium compositions, which are known to influence growth rate, virulence factor production and degradation, as well as the virulence factors' association to the cell. This study quantifies the impact of

Species-relevant inescapable stress differently influences memory consolidation and retrieval of mice in a spatial radial arm maze.

Science.gov (United States)

Janitzky, K; Schwegler, H; Kröber, A; Roskoden, T; Yanagawa, Y; Linke, R

2011-05-16

Stress affects learning and there are both facilitating and impairing actions of stressors on memory processes. Here we investigated the influence of acute exposure to 2,5-dihydro-2,4,5-trimethylthiazoline (TMT), an ethological relevant stressor for rodents, on spatial memory formation and performance in a radial arm maze (RAM) task and studied TMT effects on corticosterone levels in GAD67-GFP knock-in mice and their wildtype littermates. Our results suggest that predator odor-exposure differently affects consolidation and retrieval of memory in a hippocampus-dependent spatial learning task in adult male mice, independently from their genotypes. Acute TMT-stress before retrieval facilitates performance, whereas repeated TMT-stress during consolidation exerts no influence. Additionally, we found genotype specific effects of TMT on corticosterone release. While TMT-stress tend to result in increased corticosterone release in wildtypes there was a significant decrease in transgenic mice. Taken together, these findings indicate that biologically significant predator odor-induced stress can have different actions on the strength of spatial memory formation depending on the timing with regard to memory phases. Furthermore, we suppose an impact of GABAergic mechanisms on HPA-stress axis activation to TMT resulting in absent peripheral corticosterone release of GAD67-GFP mice. Copyright © 2011 Elsevier B.V. All rights reserved.

Elastic orthorhombic anisotropic parameter inversion: An analysis of parameterization

KAUST Repository

Oh, Juwon

2016-09-15

The resolution of a multiparameter full-waveform inversion (FWI) is highly influenced by the parameterization used in the inversion algorithm, as well as the data quality and the sensitivity of the data to the elastic parameters because the scattering patterns of the partial derivative wavefields (PDWs) vary with parameterization. For this reason, it is important to identify an optimal parameterization for elastic orthorhombic FWI by analyzing the radiation patterns of the PDWs for many reasonable model parameterizations. We have promoted a parameterization that allows for the separation of the anisotropic properties in the radiation patterns. The central parameter of this parameterization is the horizontal P-wave velocity, with an isotropic scattering potential, influencing the data at all scales and directions. This parameterization decouples the influence of the scattering potential given by the P-wave velocity perturbation fromthe polar changes described by two dimensionless parameter perturbations and from the azimuthal variation given by three additional dimensionless parameters perturbations. In addition, the scattering potentials of the P-wave velocity perturbation are also decoupled from the elastic influences given by one S-wave velocity and two additional dimensionless parameter perturbations. The vertical S-wave velocity is chosen with the best resolution obtained from S-wave reflections and converted waves, little influence on P-waves in conventional surface seismic acquisition. The influence of the density on observed data can be absorbed by one anisotropic parameter that has a similar radiation pattern. The additional seven dimensionless parameters describe the polar and azimuth variations in the P- and S-waves that we may acquire, with some of the parameters having distinct influences on the recorded data on the earth\\'s surface. These characteristics of the new parameterization offer the potential for a multistage inversion from high symmetry

Elastic orthorhombic anisotropic parameter inversion: An analysis of parameterization

KAUST Repository

Oh, Juwon; Alkhalifah, Tariq Ali

2016-01-01

The resolution of a multiparameter full-waveform inversion (FWI) is highly influenced by the parameterization used in the inversion algorithm, as well as the data quality and the sensitivity of the data to the elastic parameters because the scattering patterns of the partial derivative wavefields (PDWs) vary with parameterization. For this reason, it is important to identify an optimal parameterization for elastic orthorhombic FWI by analyzing the radiation patterns of the PDWs for many reasonable model parameterizations. We have promoted a parameterization that allows for the separation of the anisotropic properties in the radiation patterns. The central parameter of this parameterization is the horizontal P-wave velocity, with an isotropic scattering potential, influencing the data at all scales and directions. This parameterization decouples the influence of the scattering potential given by the P-wave velocity perturbation fromthe polar changes described by two dimensionless parameter perturbations and from the azimuthal variation given by three additional dimensionless parameters perturbations. In addition, the scattering potentials of the P-wave velocity perturbation are also decoupled from the elastic influences given by one S-wave velocity and two additional dimensionless parameter perturbations. The vertical S-wave velocity is chosen with the best resolution obtained from S-wave reflections and converted waves, little influence on P-waves in conventional surface seismic acquisition. The influence of the density on observed data can be absorbed by one anisotropic parameter that has a similar radiation pattern. The additional seven dimensionless parameters describe the polar and azimuth variations in the P- and S-waves that we may acquire, with some of the parameters having distinct influences on the recorded data on the earth's surface. These characteristics of the new parameterization offer the potential for a multistage inversion from high symmetry

Influence of constructional energy-saving measures on the radon-concentration in the air in dwellings

International Nuclear Information System (INIS)

Grund, A.L.; Buermeyer, J.; Spizyn, A.; Zahradnik, I.; Grimm, V.; Grimm, G.; Gundlach, M.; Walpert, V.; Breckow, J.

2015-01-01

Due to energy-saving measures the air exchange in residential houses may be reduced. In order to determine time-dependent courses the indoor radon-concentrations were measured both, before and after renovation for several weeks. In addition, the most relevant climatic conditions or indoor climate factors, as e.g. the CO 2 -concentration, were measured. Verifying the renovation success, Blower-Door registered -Tests were performed, both as well before and after the renovation. Simultaneously the radon-concentration was measured. The results before and after renovation were compared with respect to seasonal parameters and the inhabitant's behavior. By investigation of the correlation coefficient the influencing parameters and the impact of the energy saving measures were analyzed. Based on the findings a model was developed to characterize the time-dependent course based on the influence quantities. The energy-saving measures at the building considerably influence the radon dynamics. Due to the denser building envelope, fresh air flows in case of underinflation caused by stack effect not only from the outside but even through the basement from the soil. Thus, by this path the radon-containing air can be transported into the dwelling's rooms as well. The influences of the users outweigh the influence of weather parameters, thus, the radonemission- rate was used for user-independent determination of the radon situation.

ASSESSING CUSTOMER SATISFACTION BASED ON QoS PARAMETERS

Directory of Open Access Journals (Sweden)

Alem Čolaković

2017-03-01

Full Text Available Measurement of customer sastisfaction is an efficient tool to detect problems in SP (Services Provider and their relationship with customers. Based on this measurement a relationship between customer satisfaction and loyalty can be established. It can determine the influence of key parameters on the number of users of services. The parameters of customer satisfaction and loyalty are numerous and depend on the network (network quality of services parameters, the client (the perception, expectations, beliefs, etc., employees (implementation of activities, technological developments, organizational structure, etc. This paper aims to show the way to identify key indicators and their weighted factors that affect customer satisfaction. This paper intends to emphasize relationship between quality of services, customer perception and loyalty and to present a model for examining the key parameters that significantly influence customer satisfaction and how these parameters influence customer loyalty.

Influence of drying air parameters on mass transfer characteristics of apple slices

Science.gov (United States)

Beigi, Mohsen

2016-10-01

To efficiently design both new drying process and equipment and/or to improve the existing systems, accurate values of mass transfer characteristics are necessary. The present study aimed to investigate the influence of drying air parameters (i.e. temperature, velocity and relative humidity) on effective diffusivity and convective mass transfer coefficient of apple slices. The Dincer and Dost model was used to determine the mass transfer characteristics. The obtained Biot number indicated that the moisture transfer in the apple slices was controlled by both internal and external resistance. The effective diffusivity and mass transfer coefficient values obtained to be in the ranges of 7.13 × 10-11-7.66 × 10-10 and 1.46 × 10-7-3.39 × 10-7 m s-1, respectively and the both of them increased with increasing drying air temperature and velocity, and decreasing relative humidity. The validation of the model showed that the model predicted the experimental drying curves of the samples with a good accuracy.

Influence of discharge parameters on capillary discharge-pumped soft X-ray laser

International Nuclear Information System (INIS)

Peng Huimin; Zheng Wudi; Yang Dawei; Zhao Yongpeng; Cheng Yuanli; Wang Qi

2005-01-01

Based on the wave shape of Marx device at National Key Laboratory of Tunable Laser Technology, Harbin Institute of Technology, the influence of discharge parameters upon the temporal evolvement of capillary discharge produced plasmas conditions and the gain coefficient of 3p-3s transition in Neon-like Ar was simulated. In the simulation, argon with a density of 1.07 x 10 -6 g·cm -3 was filled into a ceramic capillary with an inner diameter of 3.1 mm, the peak of the discharge current pulse was 27.81 kA, and the width of the current pulse was 61.4 ns. The results show that the shorter the pulse rise time is, the higher the gain coefficient is. When the pulse rise time is 20-40 ns, the peak of the current pulse is 25-40 ns, and the current pulse width is 50-70 ns, the higher gain coefficient can be obtained. (authors)

Investigation of the influence of some experimental parameters on the position of the deposition zone in a temperature-gradient tube

International Nuclear Information System (INIS)

Helas, G.; Hoffmann, P.; Bachmann, K.

1978-01-01

An investigation of the influence of some experimental parameters on thermochromatographic separations has been carried out. It is shown that the position of the deposition zone depends on separation time, purity of the inert gas, and on type and amount of the chlorinating agent. The gas flow rate and the amount of the transported compounds have no influence within the limits of experimental conditions. From the experimental results it can be concluded that in some cases the deposited compounds react with the surface or with the excess gas. (author)

Design and formulation of nano-sized spray dried efavirenz-part I: influence of formulation parameters

Energy Technology Data Exchange (ETDEWEB)

Katata, Lebogang, E-mail: lebzakate@yahoo.com; Tshweu, Lesego; Naidoo, Saloshnee; Kalombo, Lonji; Swai, Hulda [Materials Science and Manufacturing, Centre of Polymers and Composites, Council for Scientific and Industrial Research (South Africa)

2012-11-15

Efavirenz (EFV) is one of the first-line antiretroviral drugs recommended by the World Health Organisation for treating HIV. It is a hydrophobic drug that suffers from low aqueous solubility (4 {mu}g/mL), which leads to a limited oral absorption and low bioavailability. In order to improve its oral bioavailability, nano-sized polymeric delivery systems are suggested. Spray dried polycaprolactone-efavirenz (PCL-EFV) nanoparticles were prepared by the double emulsion method. The Taguchi method, a statistical design with an L{sub 8} orthogonal array, was implemented to optimise the formulation parameters of PCL-EFV nanoparticles. The types of sugar (lactose or trehalose), surfactant concentration and solvent (dichloromethane and ethyl acetate) were chosen as significant parameters affecting the particle size and polydispersity index (PDI). Small nanoparticles with an average particle size of less than 254 {+-} 0.95 nm in the case of ethyl acetate as organic solvent were obtained as compared to more than 360 {+-} 19.96 nm for dichloromethane. In this study, the type of solvent and sugar were the most influencing parameters of the particle size and PDI. Taguchi method proved to be a quick, valuable tool in optimising the particle size and PDI of PCL-EFV nanoparticles. The optimised experimental values for the nanoparticle size and PDI were 217 {+-} 2.48 nm and 0.093 {+-} 0.02.

Design and formulation of nano-sized spray dried efavirenz-part I: influence of formulation parameters

International Nuclear Information System (INIS)

Katata, Lebogang; Tshweu, Lesego; Naidoo, Saloshnee; Kalombo, Lonji; Swai, Hulda

2012-01-01

Efavirenz (EFV) is one of the first-line antiretroviral drugs recommended by the World Health Organisation for treating HIV. It is a hydrophobic drug that suffers from low aqueous solubility (4 μg/mL), which leads to a limited oral absorption and low bioavailability. In order to improve its oral bioavailability, nano-sized polymeric delivery systems are suggested. Spray dried polycaprolactone-efavirenz (PCL-EFV) nanoparticles were prepared by the double emulsion method. The Taguchi method, a statistical design with an L 8 orthogonal array, was implemented to optimise the formulation parameters of PCL-EFV nanoparticles. The types of sugar (lactose or trehalose), surfactant concentration and solvent (dichloromethane and ethyl acetate) were chosen as significant parameters affecting the particle size and polydispersity index (PDI). Small nanoparticles with an average particle size of less than 254 ± 0.95 nm in the case of ethyl acetate as organic solvent were obtained as compared to more than 360 ± 19.96 nm for dichloromethane. In this study, the type of solvent and sugar were the most influencing parameters of the particle size and PDI. Taguchi method proved to be a quick, valuable tool in optimising the particle size and PDI of PCL-EFV nanoparticles. The optimised experimental values for the nanoparticle size and PDI were 217 ± 2.48 nm and 0.093 ± 0.02.

Analysis of all dimensionful parameters relevant in gravitational dressing of conformal theories

International Nuclear Information System (INIS)

Dorn, H.; Otto, H.J.

1992-01-01

Starting from a covariant and background independent definition of normal ordered vertex operators we give an alternative derivation of the KPZ relation between conformal dimensions and their gravitational dressed partners. With our method we are able to study for arbitrary genus the dependence of N-point functions on all dimensionful parameters. Implications for the interpretation of gravitational dressed dimensions are discussed. (orig.)

The influence of fog parameters on aerosol depletion measured in the KAEVER experiments

International Nuclear Information System (INIS)

Poss, G.; Weber, D.; Fritsche, B.

1995-01-01

The release of radioactive aerosols in the environment is one of the most serious hazards in case of an accident in nuclear power plant. Many efforts have been made in the past in numerous experimental programs like NSPP, DEMONA, VANAM, LACE, MARVIKEN, others are still underway to improve the knowledge of the aerosol behavior and depletion in a reactor containment in order to estimate the possible source term and to validate computer codes. In the German single compartment KAEVER facility the influence of size distribution, morphology, composition and solubility on the aerosol behavior is investigated. One of the more specific items is to learn about open-quotes wet depletionclose quotes means, the aerosol depletion behavior in condensing atmospheres. There are no experiments known where the fog parameters like droplet size distribution, volume concentration, respectively airborne liquid water content have been measured in- and on-line explicitly. To the authors knowledge the use of the Battelle FASP photometer, which was developed especially for this reason, for the first time gives insight in condensation behavior under accident typical thermal hydraulic conditions. It delivers a basis for code validation in terms of a real comparison of measurements and calculations. The paper presents results from open-quotes wet depletionclose quotes aerosol experiments demonstrating how depletion velocity depends on the fog parameters and where obviously critical fog parameter seem to change the regime from a open-quotes pseudo dry depletionclose quotes at a relative humidity of 100% but quasi no or very low airborne liquid water content to a real open-quotes wet depletionclose quotes under the presence of fogs with varying densities. Characteristics are outlined how soluble and insoluble particles as well as aerosol mixtures behave under condensing conditions

[Are biometric parameters of anterior segment of the eyeball influenced by type 2 diabetes?].

Science.gov (United States)

Dmuchowska, Diana A; Kraśnicki, Paweł; Mariak, Zofia

2012-01-01

To answer the question whether biometric parameters of anterior segment of the eyeball are influenced by type 2 diabetes, at the stage when the lens is still transparent, so before cataract development. Fifty subjects (28 women and 22 men), at the age of 63.3 +/- 11.3 years were enrolled in this prospective study. They were divided in 2 groups: patients with type 2 diabetes (24 subjects) and analogous age group in good general health - control group (26 subjects). None of the tested individuals presented lens opacities. The planned biometric measurements included: central corneal thickness, anterior chamber depth and axial lens thickness. The data were statistically analyzed. There was no difference between the groups of both proven and potential parameters that are associated with biometric measurements of the anterior segment of the eyeball, such as: gender, age, smoking and axial length of the eye. In diabetic patients, as opposed to the subjects in the control group, statistically significantly increased lens thickness (4.78 +/- 0.50 mm vs 4.43 +/- 0.50; p = 0.016), central corneal thickness (561.5 +/- 31.6 microm vs 542.2 +/- 35.2; p = 0.047), and the tendency for shallow anterior chamber (3.06 +/- 0.40 mm vs 3.22 +/- 0.38; p = 0.159), were observed. In patients with diabetes there was no association of the biometric parameters values with the duration of diabetes and presence of diabetic retinopathy. Type 2 diabetes contributes to increased axial corneal and lens thickness at the stage when the lens is transparent, albeit it does not significantly affect anterior chamber depth.

Neoadjuvant chemoradiotherapy of rectal carcinoma. Baseline hematologic parameters influencing outcomes

Energy Technology Data Exchange (ETDEWEB)

Hodek, Miroslav; Sirak, Igor; Paluska, Petr; Kopecky, Jindrich; Petera, Jiri; Vosmik, Milan [University Hospital in Hradec Kralove, Department of Oncology and Radiotherapy, Hradec Kralove (Czech Republic); Ferko, Alexander; Oerhalmi, Julius [University Hospital in Hradec Kralove, Department of Surgery, Hradec Kralove (Czech Republic); Hovorkova, Eva; Hadzi Nikolov, Dimitar [University Hospital in Hradec Kralove, Fingerland Department of Pathology, Hradec Kralove (Czech Republic)

2016-09-15

The link between the blood count and a systemic inflammatory response (SIR) is indisputable and well described. Pretreatment hematological parameters may predict the overall clinical outcomes in many types of cancer. Thus, this study aims to systematically evaluate the relationship between baseline blood count levels and treatment response in rectal cancer patients treated with neoadjuvant chemoradiotherapy. From 2009-2015, 173 patients with locally advanced rectal cancer were retrospectively enrolled in the study and analyzed. The baseline blood count was recorded in all patients 1 week before chemoradiation. Tumor response was evaluated through pathologic findings. Blood count levels which included RBC (red blood cells), Hb (hemoglobin), PLT (platelet count), neutrophil count, WBC (white blood cells), NLR (neutrophil-to-lymphocyte ratio), and PLR (platelet-to-lymphocyte ratio) were analyzed in relation to tumor downstaging, pCR (pathologic complete response), OS (overall survival), and DFS (disease-free survival). Hb levels were associated with a response in logistic regression analysis: pCR (p = 0.05; OR 1.04, 95 % CI 1.00-1.07); T downstaging (p = 0.006; OR 1.03, 95 % CI 1.01-1.05); N downstaging (p = 0.09; OR 1.02, 95 % CI 1.00-1.04); T or N downstaging (p = 0.007; OR 1.04, 95 % CI 1.01-1.07); T and N downstaging (p = 0.02; OR 1.02, 95 % CI 1.00-1.04); Hb and RBC were the most significant parameters influencing OS; PLT was a negative prognostic factor for OS and DFS (p = 0.008 for OS); an NLR value of 2.8 was associated with the greatest significance for OS (p = 0.03) and primary tumor downstaging (p = 0.02). Knowledge of pretreatment hematological parameters appears to be an important prognostic factor in patients with rectal carcinoma. (orig.) [German] Die Verbindung zwischen dem Blutbild und der systemischen Entzuendungsreaktion (''systemic inflammatory response'', SIR) ist unbestreitbar und gut beschrieben. Aufgrund der

Influence of processing parameters on pore structure of 3D porous chitosan-alginate polyelectrolyte complex scaffolds.

Science.gov (United States)

Florczyk, Stephen J; Kim, Dae-Joon; Wood, David L; Zhang, Miqin

2011-09-15

Fabrication of porous polymeric scaffolds with controlled structure can be challenging. In this study, we investigated the influence of key experimental parameters on the structures and mechanical properties of resultant porous chitosan-alginate (CA) polyelectrolyte complex (PEC) scaffolds, and on proliferation of MG-63 osteoblast-like cells, targeted at bone tissue engineering. We demonstrated that the porous structure is largely affected by the solution viscosity, which can be regulated by the acetic acid and alginate concentrations. We found that the CA PEC solutions with viscosity below 300 Pa.s yielded scaffolds of uniform pore structure and that more neutral pH promoted more complete complexation of chitosan and alginate, yielding stiffer scaffolds. CA PEC scaffolds produced from solutions with viscosities below 300 Pa.s also showed enhanced cell proliferation compared with other samples. By controlling the key experimental parameters identified in this study, CA PEC scaffolds of different structures can be made to suit various tissue engineering applications. Copyright © 2011 Wiley Periodicals, Inc.

Atlas selection for hippocampus segmentation: Relevance evaluation of three meta-information parameters.

Science.gov (United States)

Dill, Vanderson; Klein, Pedro Costa; Franco, Alexandre Rosa; Pinho, Márcio Sarroglia

2018-04-01

Current state-of-the-art methods for whole and subfield hippocampus segmentation use pre-segmented templates, also known as atlases, in the pre-processing stages. Typically, the input image is registered to the template, which provides prior information for the segmentation process. Using a single standard atlas increases the difficulty in dealing with individuals who have a brain anatomy that is morphologically different from the atlas, especially in older brains. To increase the segmentation precision in these cases, without any manual intervention, multiple atlases can be used. However, registration to many templates leads to a high computational cost. Researchers have proposed to use an atlas pre-selection technique based on meta-information followed by the selection of an atlas based on image similarity. Unfortunately, this method also presents a high computational cost due to the image-similarity process. Thus, it is desirable to pre-select a smaller number of atlases as long as this does not impact on the segmentation quality. To pick out an atlas that provides the best registration, we evaluate the use of three meta-information parameters (medical condition, age range, and gender) to choose the atlas. In this work, 24 atlases were defined and each is based on the combination of the three meta-information parameters. These atlases were used to segment 352 vol from the Alzheimer's Disease Neuroimaging Initiative (ADNI) database. Hippocampus segmentation with each of these atlases was evaluated and compared to reference segmentations of the hippocampus, which are available from ADNI. The use of atlas selection by meta-information led to a significant gain in the Dice similarity coefficient, which reached 0.68 ± 0.11, compared to 0.62 ± 0.12 when using only the standard MNI152 atlas. Statistical analysis showed that the three meta-information parameters provided a significant improvement in the segmentation accuracy. Copyright © 2018 Elsevier Ltd

A hybrid framework for quantifying the influence of data in hydrological model calibration

Science.gov (United States)

Wright, David P.; Thyer, Mark; Westra, Seth; McInerney, David

2018-06-01

Influence diagnostics aim to identify a small number of influential data points that have a disproportionate impact on the model parameters and/or predictions. The key issues with current influence diagnostic techniques are that the regression-theory approaches do not provide hydrologically relevant influence metrics, while the case-deletion approaches are computationally expensive to calculate. The main objective of this study is to introduce a new two-stage hybrid framework that overcomes these challenges, by delivering hydrologically relevant influence metrics in a computationally efficient manner. Stage one uses computationally efficient regression-theory influence diagnostics to identify the most influential points based on Cook's distance. Stage two then uses case-deletion influence diagnostics to quantify the influence of points using hydrologically relevant metrics. To illustrate the application of the hybrid framework, we conducted three experiments on 11 hydro-climatologically diverse Australian catchments using the GR4J hydrological model. The first experiment investigated how many data points from stage one need to be retained in order to reliably identify those points that have the hightest influence on hydrologically relevant metrics. We found that a choice of 30-50 is suitable for hydrological applications similar to those explored in this study (30 points identified the most influential data 98% of the time and reduced the required recalibrations by 99% for a 10 year calibration period). The second experiment found little evidence of a change in the magnitude of influence with increasing calibration period length from 1, 2, 5 to 10 years. Even for 10 years the impact of influential points can still be high (>30% influence on maximum predicted flows). The third experiment compared the standard least squares (SLS) objective function with the weighted least squares (WLS) objective function on a 10 year calibration period. In two out of three flow

INFLUENCE OF STRUCTURAL PARAMETERS OF LOW-CARBON STEEL ON ELECTRIC ARC BURNING

Directory of Open Access Journals (Sweden)

I. O. Vakulenko

2017-10-01

Full Text Available Purpose. The article is aimed to evaluate the influence of structural parameters of low-carbon steel on arcing process. Methodology. The values of the micro- and substructure characteristics of the electrode wire metal were changed by varying the parameters of heat treatment and cold deformation by drawing. The degree of plastic deformation was obtained by drawing blanks from different initial diameter to final dimension of 1 mm. The thermal treatment was carried out in electric chamber furnace of the SNOL-1,6.2,5.1/11-IZ type. The temperature was measured by chromel-alumel thermocouple and the electromotive force was determined using the DC potentiometer. In order to obtain the substructure of different dispersion degree the steel (after quenching from temperatures and tempering at 650°C for 1 hour was subjected to cold drawing to reduction 17 – 80%. To form structure with different ferrite grain size the steel after drawing was annealed at 680°C for 1 hour. The microstructure was examined under a light and electron transmission microscope UEMV-100K at the accelerating voltage 100 kV. The grain and subgrain sizes were evaluated using the methodologies of quantitative metallography. A welding converter of the PSG-500 type was used to study the arc welding process of direct and reverse polarities. Findings. The experimentally detected value of the welding current, which depends on the degree of deformation during wire drawing, under conditions of stable arc burning of direct polarity is about an order of magnitude lower than the calculated value. Similar difference was found for the arc of reverse polarity: the experimental value of the welding current is 5...6 times less than the calculated value. Dependence analysis shows that, regardless of the polarity of the welding arc, a good enough agreement between the calculated and experimental values of the welding current is limited to deformations of 60%. For deformation degrees of more than 60

Influence of technical parameters on epicardial fat volume quantification at cardiac CT.

Science.gov (United States)

Bucher, Andreas M; Joseph Schoepf, U; Krazinski, Aleksander W; Silverman, Justin; Spearman, James V; De Cecco, Carlo N; Meinel, Felix G; Vogl, Thomas J; Geyer, Lucas L

2015-06-01

To systematically analyze the influence of technical parameters on quantification of epicardial fat volume (EATV) at cardiac CT. 153 routine cardiac CT data sets were analyzed using three-dimensional pericardial border delineation. Three image series were reconstructed per patient: (a) CTAD: coronary CT angiography (CTA), diastolic phase; (b) CTAS: coronary CTA, systolic phase; (c) CaScD: non-contrast CT, diastolic phase. EATV was calculated using three different upper thresholds (-15HU, -30 HU, -45HU). Repeated measures ANOVA, Spearman's rho, and Bland Altman plots were used. Mean EATV differed between all three image series at a -30HU threshold (CTAD 87.2 ± 38.5 ml, CTAS 90.9 ± 37.7 ml, CaScD 130.7 ± 49.5 ml, PEATV of diastolic and systolic CTA reconstructions did not differ significantly (P=0.225). Mean EATV for contrast enhanced CTA at a -15HU threshold (CTAD15 102.4 ± 43.6 ml, CTAS15 105.3 ± 42.3 ml) could be approximated most closely by non-contrast CT at -45HU threshold (CaScD45 105.3 ± 40.8 ml). The correlation was excellent: CTAS15-CTAD15, rho=0.943; CTAD15-CaScD45, rho=0.905; CTAS15-CaScD45, rho=0.924; each PEATV can differ substantially between contrast enhanced and non-contrast CT studies, which can be reconciled by threshold modification. Heart cycle phase does not significantly influence EATV measurements. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Phenozan Influence on the Physiological-Biochemical Parameters of the Young Minks Leading to Their Advanced Properties

Directory of Open Access Journals (Sweden)

Nikolai A. Balakirev

2016-01-01

Full Text Available The antioxidant influence on the physiological-biochemical parameters of productive animals is one of the most important directions in modern animal science. Phenozan is a synthetic antioxidant with high biological activities including those for animals. The positive effects of phenozan on the physiological-biochemical parameters of the mink blood were found. These effects are leading to the intensive growth, strong health, enhancement of the mink fur quality, and so forth. The total amount of the erythrocytes in the mink blood increased by about 4-5% due to phenozan inclusion in the mink diet. Even a more significant increase was found in hemoglobin content in the mink blood and erythrocytes (by about 9.5% and 8.8%, resp. due to phenozan inclusion of 100 mg/day, whereas it was found only by about 6.1–5.3% or 5.5–0.3%, owing to phenozan inclusion of 50 or 150 mg/day. For many other parameters the optimal phenozan concentration was about 100 mg/day per head according to the result obtained for all studied animal groups. Thus, phenozan can be successfully used as a biologically active compound for mink nutrition and is recommended for other farm animals.

Influence of environmental parameters on the concentration of subsurface dissolved methane in two hydroelectric power plants in Brazil

Science.gov (United States)

Silva, M. G.; Marani, L.; Alvala, P. C.

2013-12-01

Methane (CH4) is a trace gas in the atmosphere of great importance for atmospheric chemistry as one of the main greenhouse gases. There are different sources with the largest individual production associated with the degradation of organic matter submerged in flooded areas. The amount of dissolved methane that reaches the surface depends on the production in the sediments and consumption in the water column. Both processes are associated with microbial activity and consequently dependent on the physico-chemical environmental conditions. The construction of hydroelectric dams cause flooding of areas near the river that can change the characteristics of the environment and cause changes in subsurface methane concentration. In this work, we studied two hydroelectric plants located in Brazil: Batalha (17°20'39.52"S, 47°29'34.29"W), under construction when the samples were take, and Itaipu (25°24'45.00"S, 54°35'39.00"W) which has been floated over 30 years ago. The water samples to determine dissolved methane were collected approximately 5 cm near the surface. In each collection point was measured depth, water temperature, pH and redox potential. The range of dissolved methane between the two dams was similar: 0.07-10.33 μg/l (Batalha) and 0.15-10.93 μg/l (Itaipu). However, the Batalha's average (4.04 × 3.43 μg/l; median = 3.66 μg/l) was higher than that observed in Itaipu (2.15 × 1.59 μg/l; median = 2.53 μg/l). The influence of environmental parameters on the concentration of dissolved methane was evaluated by multivariate statistical techniques (Principal Component Analysis - PCA). All of the parameters had some correlation with dissolved methane, however, the greatest contribution in Batalha was associated with pH while in Itaipu was the depth. The pH variation of the various points studied in Batalha may be associated with periods of drought and flooding of the river and hence the incorporation of organic matter in the environment. The organisms

Influence of position and stimulation parameters on intracortical inhibition and facilitation in human tongue motor cortex

DEFF Research Database (Denmark)

Kothari, Mohit; Svensson, Peter; Nielsen, Jørgen Feldbæk

2014-01-01

Paired-pulse transcranial magnetic stimulation (ppTMS) can be used to assess short-interval intracortical inhibitory (SICI) and facilitatory (ICF) networks. Many methodological parameters may however influence the outcome. The aim of the study was to examine the influence of body positions (recline...... motor cortex and motor evoked potentials (MEPs) were recorded from contralateral tongue muscles. In study 1, single pulse and three ppTMS ISIs: 2, 10, 15 ms were applied 8 times each in three blocks (TS: 120%, 140% and 160% of resting motor threshold (rMT); CS: 80% of rMT) in two different body...... positions (recline and supine) randomly. In study 2, single pulse and four ppTMS ISIs: 2, 2.5, 3, 3.5 ms were applied 8 times each in randomized order in two blocks (CS: 70% and 80% of rMT; TS: 120% of rMT). There was a significant effect of body position (P=0.049), TS intensities (P

Influence of welding parameter on texture distribution and plastic deformation behavior of as-rolled AZ31 Mg alloys

Energy Technology Data Exchange (ETDEWEB)

Xin, Renlong, E-mail: rlxin@cqu.edu.cn [College of Materials Science and Engineering, Chongqing University, Chongqing (China); State Key Laboratory of Mechanical Transmission, Chongqing University, Chongqing (China); Liu, Dejia; Shu, Xiaogang; Li, Bo; Yang, Xiaofang; Liu, Qing [College of Materials Science and Engineering, Chongqing University, Chongqing (China)

2016-06-15

Friction stir welding (FSW) has promising application potential for Mg alloys. However, softening was frequently occurred in FSW Mg joints because of the presence of a β-type fiber texture. The present study aims to understand the influence of texture distribution in stir zone (SZ) on deformation behavior and joint strength of FSW Mg welds. AZ31 Mg alloy joints were obtained by FSW with two sets of welding speed and rotation rate. Detailed microstructure and texture evolutions were examined on Mg welds by electron backscatter diffraction (EBSD) techniques. It was found that the changes of welding parameters can affect texture distribution and the characteristic of texture in the transition region between SZ and thermal-mechanical affected zone (TMAZ). As a consequence, the activation ability of basal slip and extension twinning was changed, which therefore influenced joint strength, inhomogeneous plastic deformation and fracture behaviors. The present work provided some insights into understanding the texture–property relationship in FSW Mg welds and indicated that it is effective to tailor the joint performance by texture control. - Highlights: • Welding parameters largely affect the inclination angle of SZ/TMAZ boundary. • Fracture morphology is associated with the characteristic of SZ/TMAZ boundary. • The characteristic of plastic deformation is explained from the activation of basal slip.

Influence of physical and chemical parameters on the irradiation of aqueous solutions of phenol by electron beam

International Nuclear Information System (INIS)

Pellizzari, Fabien

2005-01-01

The aim of this work was the study of the influence of different parameters by electron beam irradiation on the decomposition of phenol in aqueous solution. A simulation based on a simplified mechanism emphasized the importance of the oxygenation of the solutions in the removal of phenol by ionisation. A model of the reactor used was proposed from the study of the influence of the beam energy on the decomposition of phenol. Penetration depths of the electrons were determined. Phenol degradation was found to increase with the dose rate. The fraction of the dose into several passages under the electron beam improved the abatement of the phenol. The reoxygenation of the solutions between each passage and the kinetic expressions of irradiation could explain this effect. As expected, the first by-products identified were originated from the reaction of phenol with hydroxyl radicals. [fr

Exposure to environmentally-relevant levels of ozone negatively influence pollen and fruit development

International Nuclear Information System (INIS)

Gillespie, Colin; Stabler, Daniel; Tallentire, Eva; Goumenaki, Eleni; Barnes, Jeremy

2015-01-01

A combination of in vitro and in vivo studies on tomato (Lycopersicon esculentum Mill. cv. Triton) revealed that environmentally-relevant levels of ozone (O_3) pollution adversely affected pollen germination, germ tube growth and pollen-stigma interactions – pollen originating from plants raised in charcoal-Purafil"® filtered air (CFA) exhibited reduced germ tube development on the stigma of plants exposed to environmentally-relevant levels of O_3. The O_3-induced decline in in vivo pollen viability was reflected in increased numbers of non-fertilized and fertilized non-viable ovules in immature fruit. Negative effects of O_3 on fertilization occurred regardless of the timing of exposure, with reductions in ovule viability evident in O_3 × CFA and CFA × O_3 crossed plants. This suggests O_3-induced reductions in fertilization were associated with reduced pollen viability and/or ovule development. Fruit born on trusses independently exposed to 100 nmol mol"−"1 O_3 (10 h d"−"1) from flowering exhibited a decline in seed number and this was reflected in a marked decline in the weight and size of individual fruit – a clear demonstration of the direct consequence of the effects of the pollutant on reproductive processes. Ozone exposure also resulted in shifts in the starch and ascorbic acid (Vitamin C) content of fruit that were consistent with accelerated ripening. The findings of this study draw attention to the need for greater consideration of, and possibly the adoption of weightings for the direct impacts of O_3, and potentially other gaseous pollutants, on reproductive biology during ‘risk assessment’ exercises. - Highlights: • Environmentally-relevant levels of ozone exert negative effects on pollen viability that translate into direct impacts on fruit yield. • Negative impacts of O_3 pollution on reproductive processes were evident regardless of the stage of plant development. • Exposure to environmentally-relevant levels of O_3

Key parameters analysis of hybrid HEMP simulator

International Nuclear Information System (INIS)

Mao Congguang; Zhou Hui

2009-01-01

According to the new standards on the high-altitude electromagnetic pulse (HEMP) developed by International Electrotechnical Commission (IEC), the target parameter requirements of the key structure of the hybrid HEMP simulator are decomposed. Firstly, the influences of the different excitation sources and biconical structures to the key parameters of the radiated electric field wave shape are investigated and analyzed. Then based on the influence curves the target parameter requirements of the pulse generator are proposed. Finally the appropriate parameters of the biconical structure and the excitation sources are chosen, and the computational result of the electric field in free space is presented. The results are of great value for the design of the hybrid HEMP simulator. (authors)

Relevant optical properties for direct restorative materials.

Science.gov (United States)

Pecho, Oscar E; Ghinea, Razvan; do Amaral, Erika A Navarro; Cardona, Juan C; Della Bona, Alvaro; Pérez, María M

2016-05-01

To evaluate relevant optical properties of esthetic direct restorative materials focusing on whitened and translucent shades. Enamel (E), body (B), dentin (D), translucent (T) and whitened (Wh) shades for E (WhE) and B (WhB) from a restorative system (Filtek Supreme XTE, 3M ESPE) were evaluated. Samples (1 mm thick) were prepared. Spectral reflectance (R%) and color coordinates (L*, a*, b*, C* and h°) were measured against black and white backgrounds, using a spectroradiometer, in a viewing booth, with CIE D65 illuminant and d/0° geometry. Scattering (S) and absorption (K) coefficients and transmittance (T%) were calculated using Kubelka-Munk's equations. Translucency (TP) and opalescence (OP) parameters and whiteness index (W*) were obtained from differences of CIELAB color coordinates. R%, S, K and T% curves from all shades were compared using VAF (Variance Accounting For) coefficient with Cauchy-Schwarz inequality. Color coordinates and optical parameters were statistically analyzed using one-way ANOVA, Tukey's test with Bonferroni correction (α=0.0007). Spectral behavior of R% and S were different for T shades. In addition, T shades showed the lowest R%, S and K values, as well as the highest T%, TP an OP values. In most cases, WhB shades showed different color and optical properties (including TP and W*) than their corresponding B shades. WhE shades showed similar mean W* values and higher mean T% and TP values than E shades. When using whitened or translucent composites, the final color is influenced not only by the intraoral background but also by the color and optical properties of multilayers used in the esthetic restoration. Copyright © 2016 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Relationship between bacterial diversity and environmental parameters during composting of different raw materials.

Science.gov (United States)

Wang, Xueqin; Cui, Hongyang; Shi, Jianhong; Zhao, Xinyu; Zhao, Yue; Wei, Zimin

2015-12-01

The aim of this study was to compare the bacterial structure of seven different composts. The primary environmental factors affecting bacterial species were identified, and a strategy to enhance the abundance of uncultured bacteria through controlling relevant environmental parameters was proposed. The results showed that the physical-chemical parameters of each different pile changed in its own manner during composting, which affected the structure and succession of bacteria in different ways. DGGE profiles showed that there were 10 prominent species during composting. Among them, four species existed in all compost types, two species existed in several piles and four species were detected in a single material. Redundancy analysis results showed that bacterial species compositions were significantly influenced by C/N and moisture (p<0.05). The optimal range of C/N was 14-27. Based on these results, the primary environmental factors affecting a certain species were further identified as a potential control of bacterial diversity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Bootstrapping agency: How control-relevant information affects motivation.

Science.gov (United States)

Karsh, Noam; Eitam, Baruch; Mark, Ilya; Higgins, E Tory

2016-10-01

How does information about one's control over the environment (e.g., having an own-action effect) influence motivation? The control-based response selection framework was proposed to predict and explain such findings. Its key tenant is that control relevant information modulates both the frequency and speed of responses by determining whether a perceptual event is an outcome of one's actions or not. To test this framework empirically, the current study examines whether and how temporal and spatial contiguity/predictability-previously established as being important for one's sense of agency-modulate motivation from control. In 5 experiments, participants responded to a cue, potentially triggering a perceptual effect. Temporal (Experiments 1a-c) and spatial (Experiments 2a and b) contiguity/predictability between actions and their potential effects were experimentally manipulated. The influence of these control-relevant factors was measured, both indirectly (through their effect on explicit judgments of agency) and directly on response time and response frequency. The pattern of results was highly consistent with the control-based response selection framework in suggesting that control relevant information reliably modulates the impact of "having an effect" on different levels of action selection. We discuss the implications of this study for the notion of motivation from control and for the empirical work on the sense of agency. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

INFLUENCE ANALYSES OF DESIGNED CHARACTERISTICS OF THE ELEVATOR TO THE PARAMETERS OF ITS DRIVE

Directory of Open Access Journals (Sweden)

V. M. Bohomaz

2015-04-01

Full Text Available Purpose. A drive behaves to the basic elements of scoop band elevators. To determine the drive power calculations are carried out according to standard methods, which take plenty of time. It is necessary to conduct the analysis of influence of project characteristics on the parameters of high-speed drive in a scoop bent elevator and to build the improved algorithm of speed-up determination of its drive power on project descriptions, that will take into account the type of load, rise height, necessary productivity, standard parameters of scoops and tape. Methodology. Using parametric dependences of elevators drive power on its project characteristics, received by the author earlier, the improved algorithm of speed-up determination of elevators high-speed drive power with deep and shallow scoops at set type of load, productivity, rise height was offered. Findings. The algorithm of drive power speed-up determination of high-speed vertical elevators with deep and shallow scoops depending on project parameters was offered. The example of such algorithm application is considered for an elevator that is intended for transporting of cement. Analytical dependences of drive power of such elevator are determined on the productivity and rise height. Corresponding graphic dependences were built and character of drive power changes during the size changing of any project characteristics was determined. Originality. The improved algorithm of drive power elevator determination at the given project characteristics (type of load, rise height, productivity that takes into account standard sizes, parameters of scoops and ribbons, was built at first time. Practical value. The use of an offered algorithm of calculation gives the possibility of relatively fast determination of reference value of high-speed elevators drive power with deep and shallow scoops, to build graphic dependences of drive power on the values of the productivity and rise height at the certain

Assessment of input function distortions on kinetic model parameters in simulated dynamic 82Rb PET perfusion studies

International Nuclear Information System (INIS)

Meyer, Carsten; Peligrad, Dragos-Nicolae; Weibrecht, Martin

2007-01-01

Cardiac 82 rubidium dynamic PET studies allow quantifying absolute myocardial perfusion by using tracer kinetic modeling. Here, the accurate measurement of the input function, i.e. the tracer concentration in blood plasma, is a major challenge. This measurement is deteriorated by inappropriate temporal sampling, spillover, etc. Such effects may influence the measured input peak value and the measured blood pool clearance. The aim of our study is to evaluate the effect of input function distortions on the myocardial perfusion as estimated by the model. To this end, we simulate noise-free myocardium time activity curves (TACs) with a two-compartment kinetic model. The input function to the model is a generic analytical function. Distortions of this function have been introduced by varying its parameters. Using the distorted input function, the compartment model has been fitted to the simulated myocardium TAC. This analysis has been performed for various sets of model parameters covering a physiologically relevant range. The evaluation shows that ±10% error in the input peak value can easily lead to ±10-25% error in the model parameter K 1 , which relates to myocardial perfusion. Variations in the input function tail are generally less relevant. We conclude that an accurate estimation especially of the plasma input peak is crucial for a reliable kinetic analysis and blood flow estimation

The influence of bioavailable heavy metals and microbial parameters of soil on the metal accumulation in rice grain.

Science.gov (United States)

Xiao, Ling; Guan, Dongsheng; Peart, M R; Chen, Yujuan; Li, Qiqi; Dai, Jun

2017-10-01

A field-based study was undertaken to analyze the effects of soil bioavailable heavy metals determined by a sequential extraction procedure, and soil microbial parameters on the heavy metal accumulation in rice grain. The results showed that Cd, Cr, Cu, Ni, Pb and Zn concentrations in rice grain decreases by 65.9%, 78.9%, 32.6%, 80.5%, 61.0% and 15.7%, respectively in the sites 3 (far-away), compared with those in sites 1 (close-to). Redundancy analysis (RDA) indicated that soil catalase activity, the MBC/MBN ratio, along with bioavailable Cd, Cr and Ni could explain 68.9% of the total eigenvalue, indicating that these parameters have a great impact on the heavy metal accumulation in rice grain. The soil bioavailable heavy metals have a dominant impact on their accumulation in rice grain, with a variance contribution of 60.1%, while the MBC/MBN has a regulatory effect, with a variance contribution of 4.1%. Stepwise regression analysis showed that the MBC/MBN, urease and catalase activities are the key microbial parameters that affect the heavy metal accumulation in rice by influencing the soil bioavailable heavy metals or the translocation of heavy metals in rice. RDA showed an interactive effect between Cu, Pb and Zn in rice grain and the soil bioavailable Cd, Cr and Ni. The heavy metals in rice grain, with the exception of Pb, could be predicted by their respective soil bioavailable heavy metals. The results suggested that Pb accumulation in rice grain was mainly influenced by the multi-metal interactive effects, and less affected by soil bioavailable Pb. Copyright © 2017 Elsevier Ltd. All rights reserved.

Influence of oxygen, nitrogen and carbon on the lattice parameter of uranium mono-carbide; Influence de l'oxygene, de l'azote et du carbone sur le parametre reticulaire du monocarbure d'uranium

Energy Technology Data Exchange (ETDEWEB)

Magnier, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1966-04-15

The author studies the influence of oxygen and nitrogen contents on the lattice parameter of U(C,O,N) solid solutions around UC composition. The whole data conducts to a determination of the solubility of oxygen in UC: a U(C(1-x)O(x)) solid solution exist if x if smaller than 0.37. The author studies also the influence of carbon content on the lattice parameter of U-UC solid solutions around UC. This study conducts to the determination of the solubility of U in UC at the different temperatures. Consequences upon uranium-carbon diagram are envisaged. (author) [French] L'auteur etudie quantitativement l'influence de l'oxygene et de l'azote sur le parametre reticulaire des solutions solides U(C,O,N) proches de UC. Cette etude permet la determination de la solubilite de l'oxygene dans UC: on montre l'existence d'une solution solide U(C(1-x)O(x)) lorsque x est compris entre 0 et 0,37. Par ailleurs l'auteur etudie l'influence de la teneur en carbone sur le parametre des solutions solides U-UC proches de UC. Cette etude permet la determination de la solubilite de l'uranium dans UC aux differentes temperatures. On envisage enfin les modifications apportees par cette etude au diagramme uranium-carbone. (auteur)

[Relevance of Vascular Trauma in Trauma Care - Impact on Clinical Course and Mortality].

Science.gov (United States)

Lech, L; Jerkku, T; Kanz, K-G; Wierer, M; Mutschler, W; Koeppel, T A; Lefering, R; Banafsche, R

2016-10-01

There is a lack of evidence as to the relevance of vascular trauma (VT) in patients with severe injuries. Therefore, we reviewed registry data in the present study in order to systematically objectify the effect of VT in these patients. This study aimed to provide an adequate picture of the relevance of vascular trauma and to identify adverse prognostic factors. In a retrospective analysis of records from the TraumaRegister DGU® (TR-DGU) in two subgroups with moderate and severe VT, we examined the records for differences in terms of morbidity, mortality, follow-up and prognostic parameters compared to patients without VT with the same ISS. From a total of 42,326 patients, 2,961 (7 %) had a VT, and in 2,437 cases a severe VT (AIS ≥ 3) was diagnosed (5.8 %). In addition to a higher incidence of shock and a 2 to 3-fold increase in fluid replacement and erythrocyte transfusion, patients with severe VT had a 60 % higher rate of multiple organ failure, and in-hospital mortality was twice as high (33.8 %). The massively increased early mortality (8.0 vs. 25.2 %) clearly illustrates how severely injured patients are placed at risk by the presence of a relevant VT with a comparable ISS. In our opinion, due to an unexpected poor prognosis in the TR-DGU data for vascular injuries, increased attention is required in the care of severely injured patients. Based on our comprehensive analysis of negative prognostic factors, a further adjustment to the standards of vascular medicine could be advisable. The influence of the level of care provided by the admitting hospital and the relevance of a further hospital transfer to prognosis and clinical outcome is currently being analysed. Georg Thieme Verlag KG Stuttgart · New York.

Characterisation of the physico-mechanical parameters of MSW.

Science.gov (United States)

Stoltz, Guillaume; Gourc, Jean-Pierre; Oxarango, Laurent

2010-01-01

Following the basics of soil mechanics, the physico-mechanical behaviour of municipal solid waste (MSW) can be defined through constitutive relationships which are expressed with respect to three physical parameters: the dry density, the porosity and the gravimetric liquid content. In order to take into account the complexity of MSW (grain size distribution and heterogeneity larger than for conventional soils), a special oedometer was designed to carry out laboratory experiments. This apparatus allowed a coupled measurement of physical parameters for MSW settlement under stress. The studied material was a typical sample of fresh MSW from a French landfill. The relevant physical parameters were measured using a gas pycnometer. Moreover, the compressibility of MSW was studied with respect to the initial gravimetric liquid content. Proposed methods to assess the set of three physical parameters allow a relevant understanding of the physico-mechanical behaviour of MSW under compression, specifically, the evolution of the limit liquid content. The present method can be extended to any type of MSW. 2010 Elsevier Ltd. All rights reserved.

Influence of Cutting Parameters on the Surface Roughness and Hole Diameter of Drilling Making Parts of Alluminium Alloy

Directory of Open Access Journals (Sweden)

Andrius Stasiūnas

2013-02-01

Full Text Available The article researches the drilling process of an aluminium alloy. The paper is aimed at analyzing the influence of cutting speed, feed and hole depth considering hole diameter and hole surface roughness of aluminum alloy 6082 in the dry drilling process and at making empirical formulas for cutting parameters. The article also describes experimental techniques and equipment, tools and measuring devices. Experimental studies have been carried out using different cutting parameters. The obtained results have been analyzed using computer software. According to the existing techniques for measuring, surface roughness and hole diameters have been measured, empirical models have been created and the results of the conducted experiments have been inspected. The findings and recommendations are presented at the end of the work.Artcile in Lithuanian

Investigation of fuel lattice pitch changes influence on reactor performance through evaluate the neutronic parameters

International Nuclear Information System (INIS)

Zareian Ronizi, F.; Fadaei, A.H.; Setayeshi, S.; Shahidi, A.R.

2015-01-01

Highlights: • One of the most complex issues that Nu-engineers deal with is the design of NR core. • Numerous factors in nuclear core design depend on Fuel-to-Moderator volume ratio. • Aim of this research is to investigate RX performance for different lattice pitches. - Abstract: Nuclear reactor core design is one of the most complex issues that nuclear engineers deal with. The number and complexity of effective parameters and their impact on reactor design, which makes the problem difficult to solve, require precise knowledge of these parameters and their influence on the reactor operation. Numerous factors in a nuclear reactor core design depend on the Fuel-to-Moderator volume ratio, V F /V M , in a fuel cell. This ratio can be modified by changing the lattice pitch which is the thickness of water channels between fuels plates while keeping fuel slab dimensions fixed. Cooling and moderating properties of water are affected by such a change in a reactor core, and hence some parameters related to these properties might be changed. The aim of this research is to provide the suitable knowledge for nuclear core designing. To reach this goal, the first operating core of Tehran Research Reactor (TRR) with different lattice pitches is simulated, and the effect of different lattice pitches on some parameters such as effective multiplication factor (K eff ), reactor life time, distribution of neutron flux and power density in the core, as well as moderator temperature and density coefficient of reactivity are evaluated. The nuclear reactor analysis code, MTR-PC package is employed to carry out the considered calculation. Finally, the results are presented in some tables and graphs that provide useful information for nuclear engineers in the nuclear reactor core design

Influence of smectite crystal chemistry on the organization of interlayer water and cations

International Nuclear Information System (INIS)

Dazas, Baptiste

2014-01-01

Swelling clay minerals such as smectites are ubiquitous at the Earth surface and possess major hydration ability and contaminant uptake/retention capacity. As a consequence smectites exert a pivotal influence on elemental transfers in surficial environments. These properties are especially relevant also when smectites are used as sealant in engineered or geological barriers for waste disposal facilities. As interlayer H_2O molecules account for more than 80% of smectite water in under-saturated conditions, characterization of H_2O organization and dynamics in smectites interlayers is essential to determining the geometrical and dynamical properties of clay barriers for waste disposal and to predicting the mobility of contaminant whose principal vector is water. Within this general framework, the present works describe, in a first time, the structuration of interlayer water/cations in saturated conditions. Then, in a second time, review the influence of structural parameters such as the amount and location of layer charge deficit and the chemical composition (and more especially the presence of structural fluorine/hydroxyl) on smectite hydration properties. A set of samples covering the whole compositional range of swelling phyllosilicates has thus been synthesized and characterized chemically and structurally. Special attention was paid to determining the amount (water vapor sorption isotherms) and the distribution (X-ray diffraction) of interlayer water. Molecular modeling allowed unraveling the origin of the contrasting behaviors observed experimentally and to determine the influence of the different crystal-chemical parameters on smectite hydration. This step is essential for the prediction of smectite reactivity in the environment from a limited number of crystal-chemical parameters. Molecular modeling allowed unraveling the origin of the contrasting behaviors observed experimentally and to determine the influence of the different crystal-chemical parameters on

Influence of operating parameters on electrocoagulation of C.I. disperse yellow 3

Directory of Open Access Journals (Sweden)

Djamel Ghernaout

2014-12-01

Full Text Available This work deals with the electrocoagulation (EC process for an organic dye removal. The chosen organic dye is C.I. disperse yellow 3 (DY which is used in textile industry. Experiments were performed in batch mode using Al electrodes and for comparison purposes Fe electrodes. The experimental set-up was composed of 1 L beaker, two identical electrodes which are separated 2 cm from each other. The main operating parameters influencing EC process were examined such as pH, supporting electrolyte concentration CNaCl, current density i, and DY concentration. High performance EC process was shown during 45 min for 200 mg/L dye concentration at i = 350 A m-2 (applied voltage 12 V and CNaCl = 1 g L-1 reaching 98 % for pHs 3 and 10 and 99 % for pH 6. After 10 min, DY was also efficiently removed (86 % showing that EC process may be conveniently applied for textile industry wastewater treatment. EC using Fe electrodes exhibited slightly lower performance comparing EC using Al electrodes.

Influence of different test parameters on in vitro drug release from topical diclofenac formulations in a vertical diffusion cell setup.

Science.gov (United States)

Klein, S

2013-07-01

In the past decades, the vertical diffusion cell has emerged as a useful device for testing drug release of topical dosage forms. However, to date neither a general USP method nor formulation-related monographs have been published in international pharmacopoeia. The purpose of the present work was to examine the influence of different test parameters in a vertical diffusion cell setup on in vitro drug release from semi-solid preparations for cutaneous application. Diclofenac was selected as the model compound. Release experiments were performed in a 7 ml Microett vertical diffusion cell system. Various test parameters, including the media composition and pH, degassing, membrane material and pore size, stirring speed and stirrer type, were varied. Results obtained with different test parameter settings clearly indicate that both drug properties and instrumental details can have a huge impact on the outcome of in vitro diffusion/drug release studies with the vertical diffusion cell. Thus, the selection of adequate test parameters is crucial for the success of the release experiments and, as shown in the present study, optimal test parameters/conditions need to be established and validated on a case by case study.

Static vs. mobile sink: The influence of basic parameters on energy efficiency in wireless sensor networks.

Science.gov (United States)

Khan, Majid I; Gansterer, Wilfried N; Haring, Guenter

2013-05-15

Over the last decade a large number of routing protocols has been designed for achieving energy efficiency in data collecting wireless sensor networks. The drawbacks of using a static sink are well known. It has been argued in the literature that a mobile sink may improve the energy dissipation compared to a static one. Some authors focus on minimizing Emax , the maximum energy dissipation of any single node in the network, while others aim at minimizing Ebar , the average energy dissipation over all nodes. In our paper we take a more holistic view, considering both Emax and Ebar . The main contribution of this paper is to provide a simulation-based analysis of the energy efficiency of WSNs with static and mobile sinks. The focus is on two important configuration parameters: mobility path of the sink and duty cycling value of the nodes. On the one hand, it is well known that in the case of a mobile sink with fixed trajectory the choice of the mobility path influences energy efficiency. On the other hand, in some types of applications sensor nodes spend a rather large fraction of their total lifetime in idle mode, and therefore higher energy efficiency can be achieved by using the concept of reduced duty cycles. In particular, we quantitatively analyze the influence of duty cycling and the mobility radius of the sink as well as their interrelationship in terms of energy consumption for a well-defined model scenario. The analysis starts from general load considerations and is refined into a geometrical model. This model is validated by simulations which are more realistic in terms of duty cycling than previous work. It is illustrated that over all possible configuration scenarios in terms of duty cycle and mobility radius of the sink the energy dissipation in the WSN can vary up to a factor of nine in terms of Emax and up to a factor of 17 in terms of Ebar. It turns out that in general the choice of the duty cycle value is more important for achieving energy

The electronic system for mechanical oscillation parameters registration

Directory of Open Access Journals (Sweden)

Bulavin L. A.

2008-08-01

Full Text Available On the basis of the 8-bit microcontroller Microchip PIC16F630 the digital electronic device for harmonic oscillation parameters registration was developed. The device features are simple electric circuit and high operating speed (response time is less than 10 microseconds. The relevant software for the computer-controlled recording of harmonic oscillation parameters was designed. The device can be used as a part of the experimental setup for consistent fluids rheological parameters measurements.

Enabling multi-level relevance feedback on PubMed by integrating rank learning into DBMS.

Science.gov (United States)

Yu, Hwanjo; Kim, Taehoon; Oh, Jinoh; Ko, Ilhwan; Kim, Sungchul; Han, Wook-Shin

2010-04-16

Finding relevant articles from PubMed is challenging because it is hard to express the user's specific intention in the given query interface, and a keyword query typically retrieves a large number of results. Researchers have applied machine learning techniques to find relevant articles by ranking the articles according to the learned relevance function. However, the process of learning and ranking is usually done offline without integrated with the keyword queries, and the users have to provide a large amount of training documents to get a reasonable learning accuracy. This paper proposes a novel multi-level relevance feedback system for PubMed, called RefMed, which supports both ad-hoc keyword queries and a multi-level relevance feedback in real time on PubMed. RefMed supports a multi-level relevance feedback by using the RankSVM as the learning method, and thus it achieves higher accuracy with less feedback. RefMed "tightly" integrates the RankSVM into RDBMS to support both keyword queries and the multi-level relevance feedback in real time; the tight coupling of the RankSVM and DBMS substantially improves the processing time. An efficient parameter selection method for the RankSVM is also proposed, which tunes the RankSVM parameter without performing validation. Thereby, RefMed achieves a high learning accuracy in real time without performing a validation process. RefMed is accessible at http://dm.postech.ac.kr/refmed. RefMed is the first multi-level relevance feedback system for PubMed, which achieves a high accuracy with less feedback. It effectively learns an accurate relevance function from the user's feedback and efficiently processes the function to return relevant articles in real time.

[Relevance of Personality Factors for Successful Vocational Rehabilitation].

Science.gov (United States)

Arling, V; Slavchova, V; Knispel, J; Spijkers, W

2016-02-01

The Main purpose of vocational rehabilitation is occupational reintegration of clients into the job market who have lost their job or whose job is threatened because of a handicap or chronicl illness. With regard to existing evidence for the relevance of personality factors for work performance and job achievement, the present study investigated the influence of participants' personality factors on a successful reintegration after a retraining program in a vocational training center over 2 years. A central research objective was to identify prognostic personality factors for successful vocational integration. In this longitudinal study 15 vocational training centers participated at 3 time points of measurement (T1, T2 and T3). Data gathering was based on rehabilitants' self-reports (standardized questionnaires: SVF, BSW, SPR, CSES) about personality aspects. First data collection started at the beginning (T1) and a second survey was conducted at the end of the training 2 years later (T2). Based on the data at measurement points T1 and T2, 4 prognostic models were computed (binary logistic regression analysis) and evaluated, examining the differenzial influence of several scales and items on direct reintegration after completing the vocational retraining and reintegration status 6 months later (T3). As expected, different variables turned out to be relevant for occupational integration at the end of the training program and 6 months later. Correspondingly other variables appeared to be relevant for occupational reintegration at T1 and at T2. At the end of the vocational training program, approximately 24% of the participants had a job. With respect to direct reintegration, regression analysis revealed that vocational self-efficacy (R(2)=0,175) and self-evaluation were relevant (R(2)=0,383). Approximately 70% of the participants had gotten a job 6 months later. Several stress coping strategies (R(2)=0,170), estimation of the own reintegration prognosis and aspects

Properties and clinical relevance of osteoinductive biomaterials

NARCIS (Netherlands)

Habibovic, Pamela

2005-01-01

This thesis had two main goals: (¿) to investigate parameters influencing osteoinductive potential of biomaterials in order to unravel the mechanism underlying osteoinduction and (¿¿) to investigate performance of osteoinductive biomaterials orthotopically in order to get insight into their clinical

Task 4.1: Development of a framework for creating a databank to generate probability density functions for process parameters

International Nuclear Information System (INIS)

Burgazzi, Luciano

2011-01-01

PSA analysis should be based on the best available data for the types of equipment and systems in the plant. In some cases very limited data may be available for evolutionary designs or new equipments, especially in the case of passive systems. It has been recognized that difficulties arise in addressing the uncertainties related to the physical phenomena and characterizing the parameters relevant to the passive system performance evaluation, since the unavailability of a consistent operational and experimental data base. This lack of experimental evidence and validated data forces the analyst to resort to expert/engineering judgment to a large extent, thus making the results strongly dependent upon the expert elicitation process. This prompts the need for the development of a framework for constructing a database to generate probability distributions for the parameters influencing the system behaviour. The objective of the task is to develop a consistent framework aimed at creating probability distributions for the parameters relevant to the passive system performance evaluation. In order to achieve this goal considerable experience and engineering judgement are also required to determine which existing data are most applicable to the new systems or which generic data bases or models provide the best information for the system design. Eventually in case of absence of documented specific reliability data, documented expert judgement coming out from a well structured procedure could be used to envisage sound probability distributions for the parameters under interest

Influence of combined pretreatments on color parameters during convective drying of Mirabelle plum ( Prunus domestica subsp. syriaca)

Science.gov (United States)

Dehghannya, Jalal; Gorbani, Rasoul; Ghanbarzadeh, Babak

2017-07-01

Discoloration and browning are caused primarily by various reactions, including Maillard condensation of hexoses and amino components, phenol polymerization and pigment destruction. Convective drying can be combined with various pretreatments to help reduce undesired color changes and improve color parameters of dried products. In this study, effects of ultrasound-assisted osmotic dehydration as a pretreatment before convective drying on color parameters of Mirabelle plum were investigated. Variations of L* (lightness), a* (redness/greenness), b* (yellowness/blueness), total color change (ΔE), chroma, hue angle and browning index values were presented versus drying time during convective drying of control and pretreated Mirabelle plums as influenced by ultrasonication time, osmotic solution concentration and immersion time in osmotic solution. Samples pretreated with ultrasound for 30 min and osmotic solution concentration of 70% had a more desirable color among all other pretreated samples, with the closest L*, a* and b* values to the fresh one, showing that ultrasound and osmotic dehydration are beneficial to the color of final products after drying.

Considering the influence of stimulation parameters on the effect of conventional and high-definition transcranial direct current stimulation.

Science.gov (United States)

To, Wing Ting; Hart, John; De Ridder, Dirk; Vanneste, Sven

2016-01-01

Recently, techniques to non-invasively modulate specific brain areas gained popularity in the form of transcranial direct current stimulation (tDCS) and high-definition transcranial direct current stimulation. These non-invasive techniques have already shown promising outcomes in various studies with healthy subjects as well as patient populations. Despite widespread dissemination of tDCS, there remain significant unknowns about the influence of a diverse number of tDCS parameters (e.g. polarity, size, position of electrodes & duration of stimulation) in inducing neurophysiological and behavioral effects. This article explores both techniques starting with the history of tDCS, to the differences between conventional tDCS and high-definition transcranial direct current stimulation, the underlying physiological mechanism, the (in)direct effects, the applications of tDCS with varying parameters, the efficacy, the safety issues and the opportunities for future research.

Influence of processing parameters on microstructure and tensile properties of TG6 titanium alloy

International Nuclear Information System (INIS)

Wang Tao; Guo Hongzhen; Wang Yanwei; Yao Zekun

2010-01-01

Research highlights: → This paper highlights the relationships among processing parameters, microstructure and tensile properties of TG6 high temperature titanium alloy. → The microstructural evolutions under different processing parameters were studied by the quantitative metallography, and the effects of microstructure on room and high temperature tensile properties of TG6 alloy were analysed by SEM and TEM. → Linear relationships of elongation vs. volume fraction of primary α phase and ultimate tensile strength vs. thickness of lamellar α phase were determined. - Abstract: Near-isothermal forging of the TG6 titanium alloy was conducted on microprocessor-controlled 630 ton hydraulic press at the deformation temperatures ranging from 850 deg. C to 1045 deg. C, the strain rates of 0.0008 s -1 , 0.003 s -1 and 0.008 s -1 and the deformation degree from 10% to 70%, and then different double heat treatments were applied to the forged specimens. The microstructural evolutions were researched by optical microscope and the microstructural features, i.e. volume fraction of primary α phase and thickness of lamellar α phase, were measured by means of the image analysis software. The room and high temperature tensile properties were obtained for all the specimens. Effects of microstructure on the properties were analysed by scanning electronic microscope. It was found that tenslie properties depended on microstructural features strongly. The plots of ultimate tensile strength vs. thickness of α lamellae and elongation vs. volume fraction of primary α phase produced straight lines. The liner equations were determined by fitting the experimental date, respectively. Compared to other parameters, heat treatment had more influence on the tensile strength and the tensile plasticity was more sensitive to the forging temperature.

Influence of the Processing Parameters on the Fiber-Matrix-Interphase in Short Glass Fiber-Reinforced Thermoplastics

Directory of Open Access Journals (Sweden)

Anna Katharina Sambale

2017-06-01

Full Text Available The interphase in short fiber thermoplastic composites is defined as a three-dimensional, several hundred nanometers-wide boundary region at the interface of fibers and the polymer matrix, exhibiting altered mechanical properties. This region is of key importance in the context of fiber-matrix adhesion and the associated mechanical strength of the composite material. An interphase formation is caused by morphological, as well as thermomechanical processes during cooling of the plastic melt close to the glass fibers. In this study, significant injection molding processing parameters are varied in order to investigate the influence on the formation of an interphase and the resulting mechanical properties of the composite. The geometry of the interphase is determined using nano-tribological techniques. In addition, the influence of the glass fiber sizing on the geometry of the interphase is examined. Tensile tests are used in order to determine the resulting mechanical properties of the produced short fiber composites. It is shown that the interphase width depends on the processing conditions and can be linked to the mechanical properties of the short fiber composite.

Influence of friction stir welding process and tool parameters on strength properties of AA7075-T6 aluminium alloy joints

International Nuclear Information System (INIS)

Rajakumar, S.; Muralidharan, C.; Balasubramanian, V.

2011-01-01

The aircraft aluminium alloys generally present low weldability by traditional fusion welding process. The development of the friction stir welding has provided an alternative improved way of satisfactorily producing aluminium joints, in a faster and reliable manner. In this present work, the influence of process and tool parameters on tensile strength properties of AA7075-T 6 joints produced by friction stir welding was analysed. Square butt joints were fabricated by varying process parameters and tool parameters. Strength properties of the joints were evaluated and correlated with the microstructure, microhardness of weld nugget. From this investigation it is found that the joint fabricated at a tool rotational speed of 1400 rpm, welding speed of 60 mm/min, axial force of 8 kN, using the tool with 15 mm shoulder diameter, 5 mm pin diameter, 45 HRc tool hardness yielded higher strength properties compared to other joints.

The influence of cavity parameters on the combustion oscillation in a single-side expansion scramjet combustor

Science.gov (United States)

Ouyang, Hao; Liu, Weidong; Sun, Mingbo

2017-08-01

Cavity has been validated to be efficient flameholders for scramjet combustors, but the influence of its parameters on the combustion oscillation in scramjet combustor has barely been studied. In the present work, a series of experiments focusing on this issue have been carried out. The influence of flameholding cavity position, its length to depth ratio L/D and aft wall angle θ and number on ethylene combustion oscillation characteristics in scramjet combustor has been researched. The obtained experimental results show that, as the premixing distance between ethylene injector and flameholding cavity varies, the ethylene combustion flame will take on two distinct forms, small-amplitude high frequency fluctuation, and large-amplitude low frequency oscillation. The dominant frequency of the large-amplitude combustion oscillation is in inverse proportion to the pre-mixing distance. Moreover, the influence of cavity length to depth ratio and the aft wall angleθexists diversity when the flameholding cavity position is different and can be recognized as unnoticeable compared to the impact of the premixing distance. In addition, we also find that, when the premixing distance is identical and sufficient, increasing the number of tandem flameholding cavities can change the dominant frequency of combustion oscillation hardly, let alone avoid the combustion oscillation. It is believed that the present investigation will provide a useful reference for the design of the scramjet combustor.

Fungal Contaminants in Drinking Water Regulation? A Tale of Ecology, Exposure, Purification and Clinical Relevance

Directory of Open Access Journals (Sweden)

Monika Novak Babič

2017-06-01

Full Text Available Microbiological drinking water safety is traditionally monitored mainly by bacterial parameters that indicate faecal contamination. These parameters correlate with gastro-intestinal illness, despite the fact that viral agents, resulting from faecal contamination, are usually the cause. This leaves behind microbes that can cause illness other than gastro-intestinal and several emerging pathogens, disregarding non-endemic microbial contaminants and those with recent pathogenic activity reported. This white paper focuses on one group of contaminants known to cause allergies, opportunistic infections and intoxications: Fungi. It presents a review on their occurrence, ecology and physiology. Additionally, factors contributing to their presence in water distribution systems, as well as their effect on water quality are discussed. Presence of opportunistic and pathogenic fungi in drinking water can pose a health risk to consumers due to daily contact with water, via several exposure points, such as drinking and showering. The clinical relevance and influence on human health of the most common fungal contaminants in drinking water is discussed. Our goal with this paper is to place fungal contaminants on the roadmap of evidence based and emerging threats for drinking water quality safety regulations.

Fungal Contaminants in Drinking Water Regulation? A Tale of Ecology, Exposure, Purification and Clinical Relevance

Science.gov (United States)

Novak Babič, Monika; Gunde-Cimerman, Nina; Vargha, Márta; Tischner, Zsófia; Magyar, Donát; Veríssimo, Cristina; Sabino, Raquel; Viegas, Carla; Meyer, Wieland; Brandão, João

2017-01-01

Microbiological drinking water safety is traditionally monitored mainly by bacterial parameters that indicate faecal contamination. These parameters correlate with gastro-intestinal illness, despite the fact that viral agents, resulting from faecal contamination, are usually the cause. This leaves behind microbes that can cause illness other than gastro-intestinal and several emerging pathogens, disregarding non-endemic microbial contaminants and those with recent pathogenic activity reported. This white paper focuses on one group of contaminants known to cause allergies, opportunistic infections and intoxications: Fungi. It presents a review on their occurrence, ecology and physiology. Additionally, factors contributing to their presence in water distribution systems, as well as their effect on water quality are discussed. Presence of opportunistic and pathogenic fungi in drinking water can pose a health risk to consumers due to daily contact with water, via several exposure points, such as drinking and showering. The clinical relevance and influence on human health of the most common fungal contaminants in drinking water is discussed. Our goal with this paper is to place fungal contaminants on the roadmap of evidence based and emerging threats for drinking water quality safety regulations.

Adhesion experiments using an AFM-Parameters of influence

NARCIS (Netherlands)

Dos Santos Ferreira, O.; Gelinck, E.R.M.; Graaf, D. de; Fischer, H.

2010-01-01

Adhesion measurements were performed by AFM (Atomic Force Microscopy). It was shown that many parameters need to be controlled in order to provide reproducible and quantitative results. Adhesion forces were shown to depend on combination of materials characteristics and testing geometry as well as

Theoretical and experimental research on the influence of multiple piezoelectric effects on physical parameters of piezoelectric actuator

Directory of Open Access Journals (Sweden)

Liping Shi

2015-04-01

Full Text Available Compared with the traditional actuator of machinery and electricity, the piezoelectric actuator has the advantages of a compact structure, small volume, no mechanical friction, athermancy and no electromagnetic interference. Therefore, it has high application value in the fields of MEMS, bioengineering, medical science and so on. This article draws conclusions from the influence of multiple piezoelectric effects on the physical parameters (dielectric coefficient, equivalent capacity, energy conversion and piezoelectric coefficient of piezoelectric actuators. These data from theoretical and experimental research show the following: (1 The rate between the dielectric coefficient of piezoelectric in mechanical freedom and clamping is obtained from the secondary direct piezoelectric effect, which enhances the dielectric property, increases the dielectric coefficient and decreases the coefficient of dielectric isolation; (2 Under external field, E n ( ex = E 1 , exterior stress T = 0, that is to say, under the boundary condition of mechanical freedom, piezoelectric can store electric energy and elasticity, which obtains power density, elastic density and an electromechanical coupling factor; (3 According to the piezoelectric strain S i ( 1 , piezoelectric displacement D m ( 2 and piezoelectric strain S i ( 3 of multiple piezoelectric effects, when the dielectric coefficient of the first converse piezoelectric effect ε33 is 1326 and the dielectric coefficient of the secondary direct piezoelectric effect increases to 3336, the dielectric coefficient of the ceramic chip increases. When the piezoelectric coefficient of the first converse piezoelectric effect d33 is 595 and the piezoelectric coefficient of the secondary direct piezoelectric effect decreases to 240, the piezoelectric coefficient of the ceramic chip will decrease. It is of major significance both in the applications and in basic theory to research the influence of multiple piezoelectric

Growth parameters influencing uptake of chlordecone by Miscanthus species.

Science.gov (United States)

Liber, Yohan; Létondor, Clarisse; Pascal-Lorber, Sophie; Laurent, François

2018-05-15

Because of its high persistence in soils, t 1/2 =30years, chlordecone (CLD) was classified as a persistent organic pollutant (POP) by the Stockholm Convention in 2009.The distribution of CLD over time has been heterogeneous, ranging from banana plantations to watersheds, and contaminating all environmental compartments. The aims of this study were to (i) evaluate the potential of Miscanthus species to extract chlordecone from contaminated soils, (ii) identify the growth parameters that influence the transfer of CLD from the soil to aboveground plant parts. CLD uptake was investigated in two species of Miscanthus, C4 plants adapted to tropical climates. M. sinensis and M.×giganteus were transplanted in a soil spiked with [ 14 C]CLD at environmental concentrations (1mgkg -1 ) under controlled conditions. Root-shoot transfer of CLD was compared in the two species after two growing periods (2 then 6months) after transplantation. CLD was found in all plant organs, roots, rhizomes, stems, leaves, and even flower spikes. The highest concentration of CLD was in the roots, 5398±1636 (M.×giganteus) and 14842±3210ngg -1 DW (M. sinensis), whereas the concentration in shoots was lower, 152±28 (M.×giganteus) and 266±70ngg -1 DW (M. sinensis) in soil contaminated at 1mgkg -1 . CLD translocation led to an acropetal gradient from the bottom to the top of the plants. CLD concentrations were also monitored over two complete growing periods (10months) in M. sinensis grown in 8.05mgkg -1 CLD contaminated soils. Concentrations decreased in M. sinensis shoots after the second growth period due to the increase in organic matters in the vicinity of the roots. Results showed that, owing to their respective biomass production, the two species were equally efficient at phytoextraction of CLD. Copyright © 2017. Published by Elsevier B.V.

The Influence of Open Goals on the Acquisition of Problem-Relevant Information

Science.gov (United States)

Moss, Jarrod; Kotovsky, Kenneth; Cagan, Jonathan

2007-01-01

There have been a number of recent findings indicating that unsolved problems, or open goals more generally, influence cognition even when the current task has no relation to the task in which the goal was originally set. It was hypothesized that open goals would influence what information entered the problem-solving process. Three studies were…

Climate-relevant monitorings in Germany

International Nuclear Information System (INIS)

Metternich, P.

1993-01-01

This catalogue contains so-called meta-data; i.e. information on data. For each measuring programme or set of data, users find the address (postal address, telephone, fax-number) of the respective contact person at the beginning of the entry. The catalogue has three parts: Part A is a compilation of monitoring programmes using conventional methods adopted on the ground. Part B contains research programmes or sets of data from the field of remote sensing. In part C, data sets from time series of climate-relevant parameters are described. Section A was additionally structured according so the compartments of the climate system: Atmosphere, hydrosphere, cryosphere, biosphere. (orig./KW) [de

Nanohydroxyapatite synthesis using optimized process parameters ...

Indian Academy of Sciences (India)

3Energy Research Group, School of Engineering, Taylor's University, 47500 ... influence of different ultrasonication parameters on the prop- ... to evaluate multiple process parameters and their interaction. ..... dent and dependent variables by a 3-D representation of .... The intensities of O–H functional groups are seen to.

Ablation of clinically relevant kidney tissue volumes by high-intensity focused ultrasound: Preliminary results of standardized ex-vivo investigations.

Science.gov (United States)

Häcker, Axel; Peters, Kristina; Knoll, Thomas; Marlinghaus, Ernst; Alken, Peter; Jenne, Jürgen W; Michel, Maurice Stephan

2006-11-01

To investigate strategies to achieve confluent kidney-tissue ablation by high-intensity focused ultrasound (HIFU). Our model of the perfused ex-vivo porcine kidney was used. Tissue ablation was performed with an experimental HIFU device (Storz Medical, Kreuzlingen, Switzerland). Lesion-to-lesion interaction was investigated by varying the lesion distance (5 to 2.5 mm), generator power (300, 280, and 260 W), cooling time (10, 20, and 30 seconds), and exposure time (4, 3, and 2 seconds). The lesion rows were analyzed grossly and by histologic examination (hematoxylin-eosin and nicotinamide adenine dinucleotide staining). It was possible to achieve complete homogeneous ablation of a clinically relevant tissue volume but only by meticulous adjustment of the exposure parameters. Minimal changes in these parameters caused changes in lesion formation with holes within the lesions and lesion-to-lesion interaction. Our preliminary results show that when using this new device, HIFU can ablate a large tissue volume homogeneously in perfused ex-vivo porcine tissue under standardized conditions with meticulous adjustment of exposure parameters. Further investigations in vivo are necessary to test whether large tissue volumes can be ablated completely and reliably despite the influence of physiologic tissue and organ movement.

Influence of partially known parameter on flaw characterization in Eddy Current Testing by using a random walk MCMC method based on metamodeling

International Nuclear Information System (INIS)

Cai, Caifang; Lambert, Marc; Rodet, Thomas

2014-01-01

First, we present the implementation of a random walk Metropolis-within-Gibbs (MWG) sampling method in flaw characterization based on a metamodeling method. The role of metamodeling is to reduce the computational time cost in Eddy Current Testing (ECT) forward model calculation. In such a way, the use of Markov Chain Monte Carlo (MCMC) methods becomes possible. Secondly, we analyze the influence of partially known parameters in Bayesian estimation. The objective is to evaluate the importance of providing more specific prior information. Simulation results show that even partially known information has great interest in providing more accurate flaw parameter estimations. The improvement ratio depends on the parameter dependence and the interest shows only when the provided information is specific enough

Sensitivity of Footbridge Vibrations to Stochastic Walking Parameters

DEFF Research Database (Denmark)

Pedersen, Lars; Frier, Christian

2010-01-01

of the pedestrian. A stochastic modelling approach is adopted for this paper and it facilitates quantifying the probability of exceeding various vibration levels, which is useful in a discussion of serviceability of a footbridge design. However, estimates of statistical distributions of footbridge vibration levels...... to walking loads might be influenced by the models assumed for the parameters of the load model (the walking parameters). The paper explores how sensitive estimates of the statistical distribution of vertical footbridge response are to various stochastic assumptions for the walking parameters. The basis...... for the study is a literature review identifying different suggestions as to how the stochastic nature of these parameters may be modelled, and a parameter study examines how the different models influence estimates of the statistical distribution of footbridge vibrations. By neglecting scatter in some...

The prognostic value of time parameters in adjuvant radiotherapy of head and neck cancer. A retrospective analysis of 138 patients

International Nuclear Information System (INIS)

Dietl, B.; Schaefer, C.; Koelbl, O.

2005-01-01

Purpose: to answer the question, how the parameters waiting time, radiation treatment time and overall treatment time (OTT) influenced the endpoints overall (OS), event-free (EFS) and local recurrence-free survival (LRFS) in patients with locally advanced head-and-neck cancer, who had received postoperative radiotherapy. Patients and methods: 138 patients were included into a retrospective analysis from 10/1993 to 05/2000. Besides the time parameters waiting time, radiation treatment time and OTT, tumor- and therapy-related parameters (T-, N-, R-status, grading, tumor site, surgical technique, and postoperative hemoglobin < 12 g/dl) with potential impact on the endpoints were investigated in the univariate analysis (Kaplan-Meier log-rank test). Individual parameters with a significant impact (p = 0.05) were subjected to a multivariate Cox regression analysis. Results: besides a postoperative hemoglobin value < 12 g/dl, in the univariate analysis an OTT ≥ 105 days negatively influenced all endpoints, as well as a radiation treatment time ≥ 60 days. On multivariate Cox regression analysis, postoperative hemoglobin < 12 g/dl and an OTT ≥ 105 days were identified as independent negative prognostic factors for all endpoints. Conclusion: the waiting time should be managed according to the ASARA (as short as reasonably achievable) recommendation, radiation treatment should not be protracted exceeding an overall treatment of 105 days. Generally, time parameters should be routinely included in the standard tumor documentation, thus facilitating further evaluation of these prognostically relevant factors. (orig.)

Influence of fabrication parameter on the nanostructure and photoluminescence of highly doped p-porous silicon

Energy Technology Data Exchange (ETDEWEB)

Li, Shaoyuan [National Engineering Laboratory for Vacuum Metallurgy, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Metallurgical and energy engineering, Kunming University of Science and Technology, Kunming 650093 (China); Ma, Wenhui, E-mail: mwhsilicon@163.com [National Engineering Laboratory for Vacuum Metallurgy, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Metallurgical and energy engineering, Kunming University of Science and Technology, Kunming 650093 (China); Zhou, Yang, E-mail: zhouyangnano@163.com [National Engineering Laboratory for Vacuum Metallurgy, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Metallurgical and energy engineering, Kunming University of Science and Technology, Kunming 650093 (China); Chen, Xiuhua [Faculty of Physical Science and Technology, Yunnan University, Kunming 650091 (China); Ma, Mingyu [National Engineering Laboratory for Vacuum Metallurgy, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Metallurgical and energy engineering, Kunming University of Science and Technology, Kunming 650093 (China); Xiao, Yongyin [Faculty of Physical Science and Technology, Yunnan University, Kunming 650091 (China); Xu, Yaohui [National Engineering Laboratory for Vacuum Metallurgy, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Metallurgical and energy engineering, Kunming University of Science and Technology, Kunming 650093 (China)

2014-02-15

Porous silicon (PS) was prepared by anodizing highly doped p-type silicon in the solution of H{sub 2}O/ethanol/HF. The effects of key fabrication parameters (HF concentration, etching time and current density) on the nanostructure of PS were carefully investigated by AFM, SEM and TEM characterization. According to the experimental results, a more full-fledged model was developed to explain the crack behaviors on PS surface. The photoluminescence (PL) of resulting PS was studied by a fluorescence spectrophotometer and the results show that PL peak positions shift to shorter wavelength with the increasing current density, anodisation time and dilution of electrolyte. The PL spectra blue shift of the sample with higher porosity is confirmed by HRTEM results that the higher porosity results in smaller Si nanocrystals. A linear model (λ{sub PL/nm}=620.3–0.595P, R=0.905) was established to describe the correlation between PL peak positions and porosity of PS. -- Highlights: • The effect of fabrication parameter on the nanostructure of PS is investigated. • The influence of nanostructure on the photoluminescence behaviors is studied • A full-fledged model for expounding the crack behaviors of PS is presented. • The correlation between the porosity and PL peak blue shift is described by a linear model.

Discovering Hidden Controlling Parameters using Data Analytics and Dimensional Analysis

Science.gov (United States)

Del Rosario, Zachary; Lee, Minyong; Iaccarino, Gianluca

2017-11-01

Dimensional Analysis is a powerful tool, one which takes a priori information and produces important simplifications. However, if this a priori information - the list of relevant parameters - is missing a relevant quantity, then the conclusions from Dimensional Analysis will be incorrect. In this work, we present novel conclusions in Dimensional Analysis, which provide a means to detect this failure mode of missing or hidden parameters. These results are based on a restated form of the Buckingham Pi theorem that reveals a ridge function structure underlying all dimensionless physical laws. We leverage this structure by constructing a hypothesis test based on sufficient dimension reduction, allowing for an experimental data-driven detection of hidden parameters. Both theory and examples will be presented, using classical turbulent pipe flow as the working example. Keywords: experimental techniques, dimensional analysis, lurking variables, hidden parameters, buckingham pi, data analysis. First author supported by the NSF GRFP under Grant Number DGE-114747.

Influence of tool geometry and processing parameters on welding defects and mechanical properties for friction stir welding of 6061 Aluminium alloy

Science.gov (United States)

Daneji, A.; Ali, M.; Pervaiz, S.

2018-04-01

Friction stir welding (FSW) is a form of solid state welding process for joining metals, alloys, and selective composites. Over the years, FSW development has provided an improved way of producing welding joints, and consequently got accepted in numerous industries such as aerospace, automotive, rail and marine etc. In FSW, the base metal properties control the material’s plastic flow under the influence of a rotating tool whereas, the process and tool parameters play a vital role in the quality of weld. In the current investigation, an array of square butt joints of 6061 Aluminum alloy was to be welded under varying FSW process and tool geometry related parameters, after which the resulting weld was evaluated for the corresponding mechanical properties and welding defects. The study incorporates FSW process and tool parameters such as welding speed, pin height and pin thread pitch as input parameters. However, the weld quality related defects and mechanical properties were treated as output parameters. The experimentation paves way to investigate the correlation between the inputs and the outputs. The correlation between inputs and outputs were used as tool to predict the optimized FSW process and tool parameters for a desired weld output of the base metals under investigation. The study also provides reflection on the effect of said parameters on a welding defect such as wormhole.

WIPP Compliance Certification Application calculations parameters. Part 1: Parameter development

International Nuclear Information System (INIS)

Howarth, S.M.

1997-01-01

The Waste Isolation Pilot Plant (WIPP) in southeast New Mexico has been studied as a transuranic waste repository for the past 23 years. During this time, an extensive site characterization, design, construction, and experimental program was completed, which provided in-depth understanding of the dominant processes that are most likely to influence the containment of radionuclides for 10,000 years. Nearly 1,500 parameters were developed using information gathered from this program; the parameters were input to numerical models for WIPP Compliance Certification Application (CCA) Performance Assessment (PA) calculations. The CCA probabilistic codes frequently require input values that define a statistical distribution for each parameter. Developing parameter distributions begins with the assignment of an appropriate distribution type, which is dependent on the type, magnitude, and volume of data or information available. The development of the parameter distribution values may require interpretation or statistical analysis of raw data, combining raw data with literature values, scaling of lab or field data to fit code grid mesh sizes, or other transformation. Parameter development and documentation of the development process were very complicated, especially for those parameters based on empirical data; they required the integration of information from Sandia National Laboratories (SNL) code sponsors, parameter task leaders (PTLs), performance assessment analysts (PAAs), and experimental principal investigators (PIs). This paper, Part 1 of two parts, contains a discussion of the parameter development process, roles and responsibilities, and lessons learned. Part 2 will discuss parameter documentation, traceability and retrievability, and lessons learned from related audits and reviews

Geostatistical characterisation of geothermal parameters for a thermal aquifer storage site in Germany

Science.gov (United States)

Rodrigo-Ilarri, J.; Li, T.; Grathwohl, P.; Blum, P.; Bayer, P.

2009-04-01

The design of geothermal systems such as aquifer thermal energy storage systems (ATES) must account for a comprehensive characterisation of all relevant parameters considered for the numerical design model. Hydraulic and thermal conductivities are the most relevant parameters and its distribution determines not only the technical design but also the economic viability of such systems. Hence, the knowledge of the spatial distribution of these parameters is essential for a successful design and operation of such systems. This work shows the first results obtained when applying geostatistical techniques to the characterisation of the Esseling Site in Germany. In this site a long-term thermal tracer test (> 1 year) was performed. On this open system the spatial temperature distribution inside the aquifer was observed over time in order to obtain as much information as possible that yield to a detailed characterisation both of the hydraulic and thermal relevant parameters. This poster shows the preliminary results obtained for the Esseling Site. It has been observed that the common homogeneous approach is not sufficient to explain the observations obtained from the TRT and that parameter heterogeneity must be taken into account.

The Role of Relevance in Future Teachers' Utility Value and Interest toward Technology

Science.gov (United States)

Kale, Ugur; Akcaoglu, Mete

2018-01-01

Seeing the relevance of tasks for future use is important for developing value and interest in them. We employed a pre- and post-test quasi-experimental design using a mixed-methods approach to examine if reflecting on the relevance of technology to future teaching practices influences elementary and secondary preservice teachers' utility value…

INFLUENCE OF SURFACE-ACTIVE RHAMNOLIPID BIOCOMPLEX AND ETHYLTHIOSULFANILATE ON GROWTH AND BIOCHEMICAL PARAMETERS OF PLANTS IN THE OIL CONTAMINATED SOIL

Directory of Open Access Journals (Sweden)

A. R. Banya

2015-10-01

Full Text Available The aim of the work was to study the influence of rhamnolipid biocomplex and ethylthiosulfanilate on field pea and sorghum plants when growing in petroleum contaminated soil. Plant seeds were treated with solutions of rhamnolipid biocomplex or ethylthiosulfanilate (0.01 g/l before planting and grown in containers with soil artificially contaminated with petroleum (5, 8 and 10%. Effect of rhamnolipid biocomplex and ethylthiosulfanilate was determined by the determination of growth (weight, length plants and biochemical parameters (content of photosynthetic pigments, hydrogen peroxide, malondialdehyde. The stimulating effect of rhamnolipid biocomplex and ethylthiosulfanilate on growth parameters of field pea was shown: the shoot mass has significantly increased on 39%, root mass – on 26% if compared with the control. For sorghum somewhat smaller increase of growth parameters was observed. Under the influence of rhamnolipid biocomplex and ethylthiosulfanilate the content of photosynthetic pigments in field pea and sorghum has also increased. It was determined that the action rhamnolipid biocomplex and ethylthiosulfanilate promoted the decrease of indicators of plant oxidative reactions if compared with control: the content of hydrogen peroxide – in average on 15% and 16%, malondialdehyde – on 13.5% and 16% respectively. The results of the study testify to the effectiveness of rhamnolipid biocomplex and ethylthiosulfanilate as growth stimulators for field pea and sorghum, as well as improvement of adaptive capability of plants to unfavorable conditions. It creates the prospects of their application as effective and ecologically safe substances for the intensification of contaminated soil phytoremediation.

Influence of geometric and material properties on artifacts generated by interventional MRI devices: Relevance to PRF-shift thermometry

Energy Technology Data Exchange (ETDEWEB)

Tatebe, Ken, E-mail: Ken.Tatebe@gmail.com [Department of Radiology, University of Texas Southwestern Medical Center, 5323 Harry Hines Boulevard, Dallas, Texas 75390 (United States); Ramsay, Elizabeth; Kazem, Mohammad; Peikari, Hamed [Physical Sciences, Sunnybrook Research Institute, 2075 Bayview Avenue, Toronto, Ontario M4N3M5 (Canada); Mougenot, Charles [Philips Healthcare, 281 Hillmount Road, Markham, Ontario L6C 2S3 (Canada); Bronskill, Michael [Physical Sciences, Sunnybrook Research Institute, 2075 Bayview Avenue, Toronto, Ontario M4N3M5, Canada and Department of Medical Biophysics, University of Toronto, 610 University Avenue, Toronto, Ontario M5G2M9 (Canada); Chopra, Rajiv [Department of Radiology, University of Texas Southwestern Medical Center, 5323 Harry Hines Boulevard, Dallas, Texas 75390 (United States); Advanced Imaging Research Center, University of Texas Southwestern Medical Center, 5323 Harry Hines Boulevard, Dallas, Texas 75390 (United States); Physical Sciences, Sunnybrook Research Institute, 2075 Bayview Avenue, Toronto, Ontario M4N3M5 (Canada); Department of Medical Biophysics, University of Toronto, 610 University Avenue, Toronto, Ontario M5G2M9 (Canada)

2016-01-15

Purpose: Magnetic resonance imaging (MRI) is capable of providing valuable real-time feedback during medical procedures, partly due to the excellent soft-tissue contrast available. Several technical hurdles still exist to seamless integration of medical devices with MRI due to incompatibility of most conventional devices with this imaging modality. In this study, the effect of local perturbations in the magnetic field caused by the magnetization of medical devices was examined using finite element analysis modeling. As an example, the influence of the geometric and material characteristics of a transurethral high-intensity ultrasound applicator on temperature measurements using proton resonance frequency (PRF)-shift thermometry was investigated. Methods: The effect of local perturbations in the magnetic field, caused by the magnetization of medical device components, was examined using finite element analysis modeling. The thermometry artifact generated by a transurethral ultrasound applicator was simulated, and these results were validated against analytic models and scans of an applicator in a phantom. Several parameters were then varied to identify which most strongly impacted the level of simulated thermometry artifact, which varies as the applicator moves over the course of an ablative high-intensity ultrasound treatment. Results: Key design parameters identified as having a strong influence on the magnitude of thermometry artifact included the susceptibility of materials and their volume. The location of components was also important, particularly when positioned to maximize symmetry of the device. Finally, the location of component edges and the inclination of the device relative to the magnetic field were also found to be important factors. Conclusions: Previous design strategies to minimize thermometry artifact were validated, and novel design strategies were identified that substantially reduce PRF-shift thermometry artifacts for a variety of device

Influence of geometric and material properties on artifacts generated by interventional MRI devices: Relevance to PRF-shift thermometry

International Nuclear Information System (INIS)

Tatebe, Ken; Ramsay, Elizabeth; Kazem, Mohammad; Peikari, Hamed; Mougenot, Charles; Bronskill, Michael; Chopra, Rajiv

2016-01-01

Purpose: Magnetic resonance imaging (MRI) is capable of providing valuable real-time feedback during medical procedures, partly due to the excellent soft-tissue contrast available. Several technical hurdles still exist to seamless integration of medical devices with MRI due to incompatibility of most conventional devices with this imaging modality. In this study, the effect of local perturbations in the magnetic field caused by the magnetization of medical devices was examined using finite element analysis modeling. As an example, the influence of the geometric and material characteristics of a transurethral high-intensity ultrasound applicator on temperature measurements using proton resonance frequency (PRF)-shift thermometry was investigated. Methods: The effect of local perturbations in the magnetic field, caused by the magnetization of medical device components, was examined using finite element analysis modeling. The thermometry artifact generated by a transurethral ultrasound applicator was simulated, and these results were validated against analytic models and scans of an applicator in a phantom. Several parameters were then varied to identify which most strongly impacted the level of simulated thermometry artifact, which varies as the applicator moves over the course of an ablative high-intensity ultrasound treatment. Results: Key design parameters identified as having a strong influence on the magnitude of thermometry artifact included the susceptibility of materials and their volume. The location of components was also important, particularly when positioned to maximize symmetry of the device. Finally, the location of component edges and the inclination of the device relative to the magnetic field were also found to be important factors. Conclusions: Previous design strategies to minimize thermometry artifact were validated, and novel design strategies were identified that substantially reduce PRF-shift thermometry artifacts for a variety of device

Influence of Alloy and Solidification Parameters on Grain Refinement in Aluminum Weld Metal due to Inoculation

Energy Technology Data Exchange (ETDEWEB)

Schempp, Philipp [BAM, Germany; Tang, Z. [BIAS, Germany; Cross, Carl E. [Los Alamos National Laboratory; Seefeld, T. [BIAS, Germany; Pittner, A. [BAM, Germany; Rethmeier, M. [BAM, Germany

2012-06-28

The goals are: (1) Establish how much Ti/B grain refiner is need to completely refine aluminum weld metal for different alloys and different welding conditions; (2) Characterize how alloy composition and solidification parameters affect weld metal grain refinement; and (3) Apply relevant theory to understand observed behavior. Conclusions are: (1) additions of Ti/B grain refiner to weld metal in Alloys 1050, 5083, and 6082 resulted in significant grain refinement; (2) grain refinement was more effective in GTAW than LBW, resulting in finer grains at lower Ti content - reason is limited time available for equiaxed grain growth in LBW (inability to occlude columnar grain growth); (3) welding travel speed did not markedly affect grain size within GTAW and LBW clusters; and (4) application of Hunt CET analysis showed experimental G to be on the order of the critical G{sub CET}; G{sub CET} was consistently higher for GTAW than for LBW.

Influence of Cutting Fluid Flow Rate and Cutting Parameters on the Surface Roughness and Flank Wear of TiAlN Coated Tool In Turning AISI 1015 Steel Using Taguchi Method

Directory of Open Access Journals (Sweden)

Moganapriya C.

2017-09-01

Full Text Available This paper presents the influence of cutting parameters (Depth of cut, feed rate, spindle speed and cutting fluid flow rate on the surface roughness and flank wear of physical vapor deposition (PVD Cathodic arc evaporation coated TiAlN tungsten carbide cutting tool insert during CNC turning of AISI 1015 mild steel. Analysis of Variance has been applied to determine the critical influence of cutting parameters. Taguchi orthogonal test design has been employed to optimize the process parameters affecting surface roughness and tool wear. Depth of cut was found to be the most dominant factor contributing to high surface roughness (67.5% of the inserts. However, cutting speed, feed rate and flow rate of cutting fluid showed minimal contribution to surface roughness. On the other hand, cutting speed (45.6% and flow rate of cutting fluid (23% were the dominant factors influencing tool wear. The optimum cutting conditions for desired surface roughness constitutes the following parameters such as medium cutting speed, low feed rate, low depth of cut and high cutting fluid flow rate. Minimal tool wear was achieved for the following process parameters such as low cutting speed, low feed rate, medium depth of cut and high cutting fluid flow rate.

On the relationship between input parameters in two-mass vocal-fold model with acoustical coupling an signal parameters of the glottal flow

NARCIS (Netherlands)

van Hirtum, Annemie; Lopez, Ines; Hirschberg, Abraham; Pelorson, Xavier

2003-01-01

In this paper the sensitivity of the two-mass model with acoustical coupling to the model input-parameters is assessed. The model-output or the glottal volume air flow is characterised by signal-parameters in the time-domain. The influence of changing input-parameters on the signal-parameters is

Influence of Chemical Parameters on Artemia sp. (Crustacea: Anostraca Population in Al Wathba Lake in the Abu Dhabi Emirate, UAE

Directory of Open Access Journals (Sweden)

Anitha Saji

2016-04-01

Full Text Available Long term monitoring programme on Brine shrimp (Artemia sp. is being carried out by the Environment Agency, Abu Dhabi, United Arab Emirates (EAD with the prime purpose of understanding the population dynamics, ecology and habitat requirements of Artemia at Al Wathba Lake, situated within Al Wathba Wetland Reserve, which is an artificial wetland near Abu Dhabi City. The present study, being a component of this programme, intends to understand the influence of chemical parameters such as dissolved oxygen, nitrate, nitrite, phosphate, ammonia and total organic carbon on Artemia biomass and cyst production at different sites of the Al Wathba Lake. The study was carried out by sampling lake water quarterly for a period of 5 years from 2010 to 2014. The Artemia population was found to have direct impact of the above mentioned parameters on its abundance. The abundance was highest during the year 2010. Further, temperature, dissolved oxygen, nitrate and cadmium were found to be the most crucial parameters for production of Artemia. The study further aimed to determine the significant relationship between physico-chemical parameters and Artemia sp. population dynamics and cyst production.

Value Relevance of Investment Properties: Evidence from the Brazilian Capital Market

Directory of Open Access Journals (Sweden)

Ketlyn Alves Gonçalves

2017-04-01

Full Text Available This study investigates the relevance to the capital market of the assets recognized as investment properties of companies listed on the BM&F BOVESPA, in the period from 2011 to 2014. The research conducted was based on the Ohlson model (1995 and panel analysis was carried out using linear regression with POLS and Fixed and Random Effects estimators. Two hypothesis were made: (i that Earning and Equity generate accounting information relevant to investors; and (2 that Earning, Equity and Investment Property generate accounting information relevant to investors, assuming that investment properties have incremental effect on the relevance of this information relative only to earning and to equity. Both hypotheses were rejected, so it is concluded that Investment Property assets are not of value relevance in the determination of share price and do not influence the decision making of users of accounting information. The study adds to the limited literature on the value relevance of Investment Property, permitting a better understanding of the impact of accounting disclosures used by companies on their market value.

Influence of experimental parameters inherent to optical fibers on Quantum Key Distribution, the protocol BB84

Directory of Open Access Journals (Sweden)

L. Bouchoucha

2018-03-01

Full Text Available In this work, we represent the principle of quantum cryptography (QC that is based on fundamental laws of quantum physics. QC or Quantum Key Distribution (QKD uses various protocols to exchange a secret key between two communicating parties. This research paper focuses and examines the quantum key distribution by using the protocol BB84 in the case of encoding on the single-photon polarization and shows the influence of optical components parameters on the quantum key distribution. We also introduce Quantum Bit Error Rate (QBER to better interpret our results and show its relationship with the intrusion of the eavesdropper called Eve on the optical channel to exploit these vulnerabilities.

Influence of shear cutting parameters on the fatigue behavior of a dual-phase steel

Science.gov (United States)

Paetzold, I.; Dittmann, F.; Feistle, M.; Golle, R.; Haefele, P.; Hoffmann, H.; Volk, W.

2017-09-01

The influence of the edge condition of car body and chassis components made of steel sheet on fatigue behavior under dynamic loading presents a major challenge for automotive manufacturers and suppliers. The calculated lifetime is based on material data determined by the fatigue testing of specimens with polished edges. Prototype components are often manufactured by milling or laser cutting, whereby in practice, the series components are produced by shear cutting due to its cost-efficiency. Since the fatigue crack in such components usually starts from a shear cut edge, the calculated and experimental determined lifetime will vary due to the different conditions at the shear cut edges. Therefore, the material data determined with polished edges can result in a non-conservative component design. The aim of this study is to understand the relationship between the shear cutting process and the fatigue behavior of a dual-phase steel sheet. The geometry of the shear cut edge as well as the depth and degree of work hardening in the shear affected zone can be adjusted by using specific shear cutting parameters, such as die clearance and cutting edge radius. Stress-controlled fatigue tests of unnotched specimens were carried out to compare the fatigue behavior of different edge conditions. By evaluating the results of the fatigue experiments, influential shear cutting parameters on fatigue behavior were identified. It was possible to assess investigated shear cutting strategies regarding the fatigue behavior of a high-strength steel DP800.

Spatio-temporal modeling of nonlinear distributed parameter systems

CERN Document Server

Li, Han-Xiong

2011-01-01

The purpose of this volume is to provide a brief review of the previous work on model reduction and identifi cation of distributed parameter systems (DPS), and develop new spatio-temporal models and their relevant identifi cation approaches. In this book, a systematic overview and classifi cation on the modeling of DPS is presented fi rst, which includes model reduction, parameter estimation and system identifi cation. Next, a class of block-oriented nonlinear systems in traditional lumped parameter systems (LPS) is extended to DPS, which results in the spatio-temporal Wiener and Hammerstein s

Floors number influence on the instability parameter of reinforced concrete wall- or core-braced buildings

Directory of Open Access Journals (Sweden)

R. J. Ellwanger

Full Text Available This work aims to investigate the floors number influence on the instability parameter limit α1 of buildings braced by reinforced concrete walls and/or cores. Initially, it is showed how the Beck and König discrete and continuous models are utilized in order to define when a second order analysis is needed. The treatment given to this subject by the Brazilian code for concrete structures design (NBR 6118 is also presented. It follows a detailed analytical study that led to the derivation of equations for the limit α1 as functions of the floors number; a series of examples is presented to check their accuracy. Results are analyzed, showing the precision degree achieved and topics for continuity of research in this field are indicated.

The Parameters Selection of PSO Algorithm influencing On performance of Fault Diagnosis

Directory of Open Access Journals (Sweden)

He Yan

2016-01-01

Full Text Available The particle swarm optimization (PSO is an optimization algorithm based on intelligent optimization. Parameters selection of PSO will play an important role in performance and efficiency of the algorithm. In this paper, the performance of PSO is analyzed when the control parameters vary, including particle number, accelerate constant, inertia weight and maximum limited velocity. And then PSO with dynamic parameters has been applied on the neural network training for gearbox fault diagnosis, the results with different parameters of PSO are compared and analyzed. At last some suggestions for parameters selection are proposed to improve the performance of PSO.

FISCALITY – RELEVANT FACTOR INFLUENCING THE BUSINESS ENVIRONMENT

Directory of Open Access Journals (Sweden)

Ionel MĂNDESCU

2013-06-01

Full Text Available Main tool for macroeconomic management - fiscal policy consists in establishing the levels of taxation and spending in order to influence macroeconomic performance. Fiscal policy, promoted by the government authorities of any contemporary state, is directed usually to achieving microeconomic and macroeconomic goals deriving from the roles the state must fulfill in the economy, respectively the allocative role, distributive, regulatory and the stabilizer role. Governmental authorities, through the production and supply of public goods that are financed at the expense of taxes or duties, or on the public debt, affect both individuals’ utility functions and production functions of economic agents in the private sector. At the macroeconomic level, fiscal policy decisions of governmental authorities relating to either public spending or taxation can be directed towards the stimulation of development. Fiscality is a business cost in investment, where the decisions are taken by representatives of the business environment.

Computer-aided detection of artificial pulmonary nodules using an ex vivo lung phantom: influence of exposure parameters and iterative reconstruction.

Science.gov (United States)

Wielpütz, Mark O; Wroblewski, Jacek; Lederlin, Mathieu; Dinkel, Julien; Eichinger, Monika; Koenigkam-Santos, M; Biederer, Jürgen; Kauczor, Hans-Ulrich; Puderbach, Michael U; Jobst, Bertram J

2015-05-01

To evaluate the influence of exposure parameters and raw-data based iterative reconstruction (IR) on the performance of computer-aided detection (CAD) of pulmonary nodules on chest multidetector computed tomography (MDCT). Seven porcine lung explants were inflated in a dedicated ex vivo phantom shell and prepared with n=162 artificial nodules of a clinically relevant volume and maximum diameter (46-1063 μl, and 6.2-21.5 mm). n=118 nodules were solid and n=44 part-solid. MDCT was performed with different combinations of 120 and 80 kV with 120, 60, 30 and 12 mA*s, and reconstructed with both filtered back projection (FBP) and IR. Subsequently, 16 datasets per lung were subjected to dedicated CAD software. The rate of true positive, false negative and false positive CAD marks was measured for each reconstruction. The rate of true positive findings ranged between 88.9-91.4% for FBP and 88.3-90.1% for IR (n.s.) with most exposure settings, but was significantly lower with the combination of 80 kV and 12 mA*s (80.9% and 81.5%, respectively, pvolumes 300 μl (p<0.05). Similarly, it was significantly lower for diameters <12 mm compared to ≥12 mm (p<0.05). The rate of true positives for solid and part-solid nodules was similar. Nodule CAD on chest MDCT is robust over a wide range of exposure settings. Noise reduction by IR is not detrimental for CAD, and may be used to improve image quality in the setting of low-dose MDCT for lung cancer screening. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Moisture parameters and fungal communities associated with gypsum drywall in buildings.

Science.gov (United States)

Dedesko, Sandra; Siegel, Jeffrey A

2015-12-08

Uncontrolled excess moisture in buildings is a common problem that can lead to changes in fungal communities. In buildings, moisture parameters can be classified by location and include assessments of moisture in the air, at a surface, or within a material. These parameters are not equivalent in dynamic indoor environments, which makes moisture-induced fungal growth in buildings a complex occurrence. In order to determine the circumstances that lead to such growth, it is essential to have a thorough understanding of in situ moisture measurement, the influence of building factors on moisture parameters, and the levels of these moisture parameters that lead to indoor fungal growth. Currently, there are disagreements in the literature on this topic. A literature review was conducted specifically on moisture-induced fungal growth on gypsum drywall. This review revealed that there is no consistent measurement approach used to characterize moisture in laboratory and field studies, with relative humidity measurements being most common. Additionally, many studies identify a critical moisture value, below which fungal growth will not occur. The values defined by relative humidity encompassed the largest range, while those defined by moisture content exhibited the highest variation. Critical values defined by equilibrium relative humidity were most consistent, and this is likely due to equilibrium relative humidity being the most relevant moisture parameter to microbial growth, since it is a reasonable measure of moisture available at surfaces, where fungi often proliferate. Several sources concur that surface moisture, particularly liquid water, is the prominent factor influencing microbial changes and that moisture in the air and within a material are of lesser importance. However, even if surface moisture is assessed, a single critical moisture level to prevent fungal growth cannot be defined, due to a number of factors, including variations in fungal genera and

Influence of Powder Injection Parameters in High-Pressure Cold Spray

Science.gov (United States)

Ozdemir, Ozan C.; Widener, Christian A.

2017-10-01

High-pressure cold spray systems are becoming widely accepted for use in the structural repair of surface defects of expensive machinery parts used in industrial and military equipment. The deposition quality of cold spray repairs is typically validated using coupon testing and through destructive analysis of mock-ups or first articles for a defined set of parameters. In order to provide a reliable repair, it is important to not only maintain the same processing parameters, but also to have optimum fixed parameters, such as the particle injection location. This study is intended to provide insight into the sensitivity of the way that the powder is injected upstream of supersonic nozzles in high-pressure cold spray systems and the effects of variations in injection parameters on the nature of the powder particle kinetics. Experimentally validated three-dimensional computational fluid dynamics (3D CFD) models are implemented to study the particle impact conditions for varying powder feeder tube size, powder feeder tube axial misalignment, and radial powder feeder injection location on the particle velocity and the deposition shape of aluminum alloy 6061. Outputs of the models are statistically analyzed to explore the shape of the spray plume distribution and resulting coating buildup.

Diffusion-weighted imaging of breast lesions: Region-of-interest placement and different ADC parameters influence apparent diffusion coefficient values

Energy Technology Data Exchange (ETDEWEB)

Bickel, Hubert; Pinker, Katja; Polanec, Stephan; Magometschnigg, Heinrich; Wengert, Georg; Spick, Claudio; Helbich, Thomas H.; Baltzer, Pascal [Medical University Vienna, Division of Molecular and Gender Imaging, Department of Biomedical Imaging and Image-Guided Therapy, Vienna (Austria); Bogner, Wolfgang [Medical University Vienna - MR Center of Excellence, Department of Biomedical Imaging and Image-Guided Therapy, Vienna (Austria); Bago-Horvath, Zsuzsanna [Medical University Vienna, Department of Pathology, Vienna (Austria)

2017-05-15

To investigate the influence of region-of-interest (ROI) placement and different apparent diffusion coefficient (ADC) parameters on ADC values, diagnostic performance, reproducibility and measurement time in breast tumours. In this IRB-approved, retrospective study, 149 histopathologically proven breast tumours (109 malignant, 40 benign) in 147 women (mean age 53.2) were investigated. Three radiologists independently measured minimum, mean and maximum ADC, each using three ROI placement approaches:1 - small 2D-ROI, 2 - large 2D-ROI and 3 - 3D-ROI covering the whole lesion. One reader performed all measurements twice. Median ADC values, diagnostic performance, reproducibility, and measurement time were calculated and compared between all combinations of ROI placement approaches and ADC parameters. Median ADC values differed significantly between the ROI placement approaches (p <.001). Minimum ADC showed the best diagnostic performance (AUC.928-.956), followed by mean ADC obtained from 2D ROIs (.926-.94). Minimum and mean ADC showed high intra- (ICC.85-.94) and inter-reader reproducibility (ICC.74-.94). Median measurement time was significantly shorter for the 2D ROIs (p <.001). ROI placement significantly influences ADC values measured in breast tumours. Minimum and mean ADC acquired from 2D-ROIs are useful for the differentiation of benign and malignant breast lesions, and are highly reproducible, with rapid measurement. (orig.)

Lower hybrid current drive at ITER-relevant high plasma densities

International Nuclear Information System (INIS)

Cesario, R.; Amicucci, L.; Cardinali, A.; Castaldo, C.; Marinucci, M.; Panaccione, L.; Pericoli-Ridolfini, V.; Tuccillo, A. A.; Tudisco, O.; Calabro, G.

2009-01-01

Recent experiments indicated that a further non-inductive current, besides bootstrap, should be necessary for developing advanced scenario for ITER. The lower hybrid current drive (LHCD) should provide such tool, but its effectiveness was still not proved in operations with ITER-relevant density of the plasma column periphery. Progress of the LH deposition modelling is presented, performed considering the wave physics of the edge, and different ITER-relevant edge parameters. Operations with relatively high edge electron temperatures are expected to reduce the LH || spectral broadening and, consequently, enabling the LH power to propagate also in high density plasmas ( || is the wavenumber component aligned to the confinement magnetic field). New results of FTU experiments are presented, performed by following the aforementioned modeling: they indicate that, for the first time, the LHCD conditions are established by operating at ITER-relevant high edge densities.

ASPECTS OF THE INFLUENCE OF TECHNOLOGICAL PARAMETERS ON THE TENSION PROPERTIES OF THE YARNS

Directory of Open Access Journals (Sweden)

HRISTIAN Liliana

2016-05-01

Full Text Available This paper presents the results of some experiments performed using the power system bands directly from the card to the rotor spinning machine and the spinning system used by passing the lanes on two passages mill and fed to the spinning rotor. In this study we analized the influence of technological parameters of the preparation drawing on the assessing indicators for the tensile strength of the Nm20, Nm24, Nm27 Nm34 and Nm40 yarns. The fineness range studied was made of three fiber mixtures of different varieties of cotton, coded as follows: A1-85% Soviet cotton+15% Chinese cotton medium II; A2-100% Turkish cotton medium III; A3-100% American cotton mdium IV. The method of preparation of the bands which are to be powered to the rotor spinning machine, respectively with the aggregate pile-card and the powered bands directly to the rotor spinning machine and the adding of two rolling mill, detemines different structures of bands and different degrees of untangling and orientation of the fibers, which influences the quality of the obtained yarns. This study reveals a considerable improvement of the tensile properties when the yarns are made from rolled band, which is explained by the high degree of correction and parallelization of the fibers of the rolled band, which allows a greater participation of fibers with their resistance to the resistance of the yarns.

Fatiguing exercise intensity influences the relationship between parameters reflecting neuromuscular function and postural control variables.

Directory of Open Access Journals (Sweden)

Sébastien Boyas

Full Text Available The purpose of this study was to investigate the influence of fatiguing exercise intensity on the nature and extent of fatigue-induced changes in neuromuscular function and postural stability in quiet standing. We also explored the contribution of selected neuromuscular mechanisms involved in force production to postural stability impairment observed following fatigue using an approach based on multivariate regressions. Eighteen young subjects performed 30-s postural trials on one leg with their eyes closed. Postural trials were performed before and after fatiguing exercises of different intensities: 25, 50 and 75% of maximal isometric plantarflexor torque. Fatiguing exercises consisted of sustaining a plantarflexor isometric contraction at the target intensity until task failure. Maximal isometric plantarflexor torque, electromyographic activity of plantarflexor and dorsiflexor muscles, activation level (twitch interpolation technique and twitch contractile properties of plantarflexors were used to characterize neuromuscular function. The 25% exercise was associated with greater central fatigue whereas the 50 and 75% exercises involved mostly peripheral fatigue. However, all fatiguing exercises induced similar alterations in postural stability, which was unexpected considering previous literature. Stepwise multiple regression analyses showed that fatigue-related changes in selected parameters related to neuromuscular function could explain more than half (0.51≤R(2≤0.82 of the changes in postural variables for the 25% exercise. On the other hand, regression models were less predictive (0.17≤R(2≤0.73 for the 50 and 75% exercises. This study suggests that fatiguing exercise intensity does not influence the extent of postural stability impairment, but does influence the type of fatigue induced and the neuromuscular function predictors explaining changes in postural variables.

Deep learning relevance

DEFF Research Database (Denmark)

Lioma, Christina; Larsen, Birger; Petersen, Casper

2016-01-01

train a Recurrent Neural Network (RNN) on existing relevant information to that query. We then use the RNN to "deep learn" a single, synthetic, and we assume, relevant document for that query. We design a crowdsourcing experiment to assess how relevant the "deep learned" document is, compared...... to existing relevant documents. Users are shown a query and four wordclouds (of three existing relevant documents and our deep learned synthetic document). The synthetic document is ranked on average most relevant of all....

Model parameters estimation and sensitivity by genetic algorithms

International Nuclear Information System (INIS)

Marseguerra, Marzio; Zio, Enrico; Podofillini, Luca

2003-01-01

In this paper we illustrate the possibility of extracting qualitative information on the importance of the parameters of a model in the course of a Genetic Algorithms (GAs) optimization procedure for the estimation of such parameters. The Genetic Algorithms' search of the optimal solution is performed according to procedures that resemble those of natural selection and genetics: an initial population of alternative solutions evolves within the search space through the four fundamental operations of parent selection, crossover, replacement, and mutation. During the search, the algorithm examines a large amount of solution points which possibly carries relevant information on the underlying model characteristics. A possible utilization of this information amounts to create and update an archive with the set of best solutions found at each generation and then to analyze the evolution of the statistics of the archive along the successive generations. From this analysis one can retrieve information regarding the speed of convergence and stabilization of the different control (decision) variables of the optimization problem. In this work we analyze the evolution strategy followed by a GA in its search for the optimal solution with the aim of extracting information on the importance of the control (decision) variables of the optimization with respect to the sensitivity of the objective function. The study refers to a GA search for optimal estimates of the effective parameters in a lumped nuclear reactor model of literature. The supporting observation is that, as most optimization procedures do, the GA search evolves towards convergence in such a way to stabilize first the most important parameters of the model and later those which influence little the model outputs. In this sense, besides estimating efficiently the parameters values, the optimization approach also allows us to provide a qualitative ranking of their importance in contributing to the model output. The

Parameters Evaluation of PLC Dependability and Safety

Directory of Open Access Journals (Sweden)

Juraj Zdansky

2006-01-01

Full Text Available This paper is focused on evaluation of dependability and safety parameters of PLC (Programmable Logic Controller. Achievement of requested level of these parameters is an application assumption for using PLC in control of safety critical processes. Evaluation of these parameters can be made on the base of suitable model and it can be influenced by system architecture when necessary.

Evaluation of acquisition parameters in microtomography through of analysis of carbonatic rocks

Energy Technology Data Exchange (ETDEWEB)

Santos, Thaís M.P.; Machado, Alessandra S.; Araujo, Olga M.O.; Ferreira, Cintia G.; Lopes, Ricardo T., E-mail: thaismpds@poli.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Instrumentação Nuclear

2017-07-01

X-ray computed microtomography is a powerful nondestructive technique for 2D and 3D structure analysis. However, parameters used in acquisition promote directs influence in qualitative and quantitative results in characterization of samples, due image resolution. The aim of this study is value the influence of theses parameters in results through of tests changing these parameters in different situations and scanner characterization. Results demonstrate that pixel size and detector matrix are the main parameters that influence in resolution and the necessity use additional filters for image quality. Microtomography was considered an excellent technique for characterization using the best image resolution possible. (author)

Evaluation of acquisition parameters in microtomography through of analysis of carbonatic rocks

International Nuclear Information System (INIS)

Santos, Thaís M.P.; Machado, Alessandra S.; Araujo, Olga M.O.; Ferreira, Cintia G.; Lopes, Ricardo T.

2017-01-01

X-ray computed microtomography is a powerful nondestructive technique for 2D and 3D structure analysis. However, parameters used in acquisition promote directs influence in qualitative and quantitative results in characterization of samples, due image resolution. The aim of this study is value the influence of theses parameters in results through of tests changing these parameters in different situations and scanner characterization. Results demonstrate that pixel size and detector matrix are the main parameters that influence in resolution and the necessity use additional filters for image quality. Microtomography was considered an excellent technique for characterization using the best image resolution possible. (author)

Influence of two-stream relativistic electron beam parameters on the space-charge wave with broad frequency spectrum formation

Science.gov (United States)

Alexander, LYSENKO; Iurii, VOLK

2018-03-01

We developed a cubic non-linear theory describing the dynamics of the multiharmonic space-charge wave (SCW), with harmonics frequencies smaller than the two-stream instability critical frequency, with different relativistic electron beam (REB) parameters. The self-consistent differential equation system for multiharmonic SCW harmonic amplitudes was elaborated in a cubic non-linear approximation. This system considers plural three-wave parametric resonant interactions between wave harmonics and the two-stream instability effect. Different REB parameters such as the input angle with respect to focusing magnetic field, the average relativistic factor value, difference of partial relativistic factors, and plasma frequency of partial beams were investigated regarding their influence on the frequency spectrum width and multiharmonic SCW saturation levels. We suggested ways in which the multiharmonic SCW frequency spectrum widths could be increased in order to use them in multiharmonic two-stream superheterodyne free-electron lasers, with the main purpose of forming a powerful multiharmonic electromagnetic wave.

Competitive Swimming and Handball Participation Have a Positive Influence on Bone Parameters as Assessed by Phalangeal Quantitative Ultrasound in Female Adolescents.

Science.gov (United States)

Krahenbuhl, Tathyane; Gonçalves, Ezequiel M; Guimarães, Roseane Fatima; Guerra-Junior, Gil; Barros-Filho, Antonio

2016-08-01

To examine the influence of participation in competitive sports on bone parameters, as assessed by quantitative ultrasound (QUS) of the phalanges in female adolescents. Female adolescents (n = 329, 13.0-16.7 years old) were classified into handball (n = 55), swimming (n = 49) and control (n = 225) groups. QUS was used to evaluate the amplitude-dependent speed of sound (AD-SoS) and bone transmission time (BTT), and their z-scores (zAD-SoS and zBTT) were calculated. Anthropometric measurements and Tanner's stages were also obtained. Swimmers had higher AD-SoS (2089 ± 43.8 m/s) and zAD-SoS (0.47 ± 0.8) than controls (2060 ± 54.0 m/s; 0.09 ± 1.0; both p ≤ .05) and both groups of athletes had higher BTT (handball: 1.44 ± 0.2 μs; swimming: 1.45 ± 0.2) and zBTT (handball: 0.71 ± 0.8; swimming: 0.72 ± 1.1) than the control group (1.37 ± 0.2 μs; 0.32 ± 0.9; all p ≤ .05). Swimmers had a higher total training time (TTT: 52.5 ± 27.6 months) and frequency of training per week (FT: 5.38 ± 0.1) compared with the handball group (35.9 ± 18.1; 3.32 ± 0.8; p ≤ .05). zAD-SoS, BTT and zBTT were positively correlated with FT, while BTT and zBTT showed a positive correlation with TTT. Sports practice influences bone parameters and higher bone parameter values are related to the amount of time and frequency of weekly training. The differences in phalangeal QUS parameters are independent of the impact of weight-bearing exercise.

Environmental processes and parameters influencing the consequences of an accidental release of radioactivity weather and season

International Nuclear Information System (INIS)

Boeri, G.C.

1989-01-01

Seasonal, climatic and meteorological conditions may have a substantial influence on the physical factors involved in transport and deposition of airborne contaminants, and on the transfer and accumulation of radionuclides in terrestrial and aquatic ecosystems. As well, these environmental conditions can also have a significant influence on living habits and practices, and thus on potential radiological and economical impacts. Moreover, these conditions may affect the features and the impact of countermeasures which are adopted for the protection of the public in case of an accidental release. During a Special Session that the Committee of Radiation Protection and Public Health (CRPPH) held on the 1st-2nd September 1986 to review the radiological aspects of the Chernobyl nuclear accident, it was agreed that a consultant should prepare a report reviewing different accident consequences in a radiation protection and public health perspective, and identify the influence of such parameters as time of the year, weather and environmental conditions on the overall impact and the determination of appropriate countermeasures. A Consultant Report on this issue was prepared, by Dr. G. Boeri, and submitted to the CRPPH for review and consideration at its meeting of 22nd-24th November 1987. The CRPPH subsequently agreed that the Consultant Report should be revised and completed, taking into account comments and suggestions sent to the Secretariat and focussing especially on the effect of seasonal and weather conditions in terms of their influence on the radiological impact of an accident and on the emergency countermeasures to be taken. It was decided that the Consultant Report should be developed into an Overview Paper for a workshop on this issue to be organised by the NEA in 1988

Family influences on mania-relevant cognitions and beliefs: a cognitive model of mania and reward.

Science.gov (United States)

Chen, Stephen H; Johnson, Sheri L

2012-07-01

The present study proposed and tested a cognitive model of mania and reward. Undergraduates (N = 284; 68.4% female; mean age = 20.99 years, standard deviation ± 3.37) completed measures of family goal setting and achievement values, personal reward-related beliefs, cognitive symptoms of mania, and risk for mania. Correlational analyses and structural equation modeling supported two distinct, but related facets of mania-relevant cognition: stably present reward-related beliefs and state-dependent cognitive symptoms in response to success and positive emotion. Results also indicated that family emphasis on achievement and highly ambitious extrinsic goals were associated with these mania-relevant cognitions. Finally, controlling for other factors, cognitive symptoms in response to success and positive emotion were uniquely associated with lifetime propensity towards mania symptoms. Results support the merit of distinguishing between facets of mania-relevant cognition and the importance of the family in shaping both aspects of cognition. © 2012 Wiley Periodicals, Inc.

Time of erythema onset after application of methyl nicotinate ointments as response parameter: influence of penetration kinetics and enhancing agents.

Science.gov (United States)

Remane, Y; Leopold, C S

2006-01-01

The time of erythema onset may be used as a response parameter for quantification of the cutaneous erythema response induced by methyl nicotinate. The vehicles light mineral oil (LMO; test) and medium chain triglycerides (MCT; standard) were compared with regard to the pharmacodynamic response. Moreover, the influence of penetration enhancers on the time of erythema onset was investigated under zero order penetration kinetics. The enhancers dimethyl sulfoxide, diethylene glycol monoethyl ether and three different glycerides in different concentrations were added to MCT as a standard vehicle. All preparations were applied to the forearms of volunteers under infinite dose conditions at different thermodynamic drug activity levels (0.2-3.2% of the saturation level) and different drug concentrations (0.051-0.816%), respectively. Different penetration kinetics do not influence data of erythema onset, as these data are comparable to those obtained under finite dose conditions (first order penetration kinetics). With regard to the penetration enhancers, a significantly enhanced penetration of methyl nicotinate could be observed only for diethylene glycol monoethyl ether and dimethyl sulfoxide. However, no significant difference between light mineral oil and MCT could be found with regard to penetration enhancement. The time of erythema onset is an easy and efficient parameter for quantification of the pharmacodynamic response caused by nicotinates.

Influences of pulsed current tungsten inert gas welding parameters on the tensile properties of AA 6061 aluminium alloy

International Nuclear Information System (INIS)

Senthil Kumar, T.; Balasubramanian, V.; Sanavullah, M.Y.

2007-01-01

Medium strength aluminium alloy (Al-Mg-Si alloy) has gathered wide acceptance in the fabrication of light weight structures requiring a high strength-to-weight ratio, such as transportable bridge girders, military vehicles, road tankers and railway transport systems. In any structural application of this alloy consideration its weldability is of utmost importance as welding is largely used for joining of structural components. The preferred welding process of aluminium alloy is frequently tungsten inert gas (TIG) welding due to its comparatively easier applicability and better economy. In the case of single pass TIG welding of thinner section of this alloy, the pulsed current has been found beneficial due to its advantages over the conventional continuous current process. The use of pulsed current parameters has been found to improve the mechanical properties of the welds compared to those of continuous current welds of this alloy due to grain refinement occurring in the fusion zone. Many considerations come into the picture and one need to carefully balance various pulse current parameters to arrive at an optimum combination. Hence, in this investigation an attempt has been made to study the influence of pulsed current TIG welding parameters on tensile properties of AA 6061 aluminium alloy weldments

Parameters Influencing the Growth of ZnO Nanowires as Efficient Low Temperature Flexible Perovskite-Based Solar Cells

Directory of Open Access Journals (Sweden)

Alex Dymshits

2016-01-01

Full Text Available Hybrid organic-inorganic perovskite has proved to be a superior material for photovoltaic solar cells. In this work we investigate the parameters influencing the growth of ZnO nanowires (NWs for use as an efficient low temperature photoanode in perovskite-based solar cells. The structure of the solar cell is FTO (SnO2:F-glass (or PET-ITO (In2O3·(SnO2 (ITO on, polyethylene terephthalate (PET/ZnAc seed layer/ZnO NWs/CH3NH3PbI3/Spiro-OMeTAD/Au. The influence of the growth rate and the diameter of the ZnO NWs on the photovoltaic performance were carefully studied. The ZnO NWs perovskite-based solar cell demonstrates impressive power conversion efficiency of 9.06% on a rigid substrate with current density over 21 mA/cm2. In addition, we successfully fabricated flexible perovskite solar cells while maintaining all fabrication processes at low temperature, achieving power conversion efficiency of 6.4% with excellent stability for over 75 bending cycles.

On the relationship between input parameters in the two-mass vocal-fold model with acoustical coupling and signal parameters of the glottal flow

NARCIS (Netherlands)

Hirtum, van A.; Lopez Arteaga, I.; Hirschberg, A.; Pelorson, X.

2003-01-01

In this paper the sensitivity of the two-mass model with acoustical coupling to the model input-parameters is assessed. The model-output or the glottal volume air flow is characterised by signal-parameters in the time-domain. The influence of changing input-parameters on the signal-parameters is

S-parameter at Non-Zero Temperature and Chemical Potential

DEFF Research Database (Denmark)

Søndergaard, Ulrik Ishøj; Sannino, Francesco; Pica, Claudio

2011-01-01

We compute the finite-temperature and matter density corrections to the S-parameter at the one loop level. At non-zero temperature T and matter density Lorentz symmetry breaks and therefore we suggest a suitable generalization of the S-parameter. By computing the plasma correction, we discover...... a reduction of the S-parameter in the physically relevant region of small external momenta for any non-zero chemical potential and T. In particular, the S-parameter vanishes at small m/T, where m is the mass of the fermions, due to the finite extent of the temporal direction. Our results are directly...

Influence of physical parameters on radiation protection and image quality in intra-oral radiology

Science.gov (United States)

Belinato, W.; Souza, D. N.

2011-10-01

In the world of diagnostic imaging, radiography is an important supplementary method for dental diagnosis. In radiology, special attention must be paid to the radiological protection of patients and health professionals, and also to image quality for correct diagnosis. In Brazil, the national rules governing the operation of medical and dental radiology were specified in 1998 by the National Sanitary Surveillance Agency, complemented in 2005 by the guide "Medical radiology: security and performance of equipment." In this study, quality control tests were performed in public clinics with dental X-ray equipment in the State of Sergipe, Brazil, with consideration of the physical parameters that influence radiological protection and also the quality of images taken in intra-oral radiography. The accuracy of the exposure time was considered acceptable for equipment with digital timers. Exposure times and focal-spot size variations can lead to increased entrance dose. Increased dose has also been associated with visual processing of radiographic film, which often requires repeating the radiographic examination.

Influence of physical parameters on radiation protection and image quality in intra-oral radiology

International Nuclear Information System (INIS)

Belinato, W.; Souza, D.N.

2011-01-01

In the world of diagnostic imaging, radiography is an important supplementary method for dental diagnosis. In radiology, special attention must be paid to the radiological protection of patients and health professionals, and also to image quality for correct diagnosis. In Brazil, the national rules governing the operation of medical and dental radiology were specified in 1998 by the National Sanitary Surveillance Agency, complemented in 2005 by the guide 'Medical radiology: security and performance of equipment.' In this study, quality control tests were performed in public clinics with dental X-ray equipment in the State of Sergipe, Brazil, with consideration of the physical parameters that influence radiological protection and also the quality of images taken in intra-oral radiography. The accuracy of the exposure time was considered acceptable for equipment with digital timers. Exposure times and focal-spot size variations can lead to increased entrance dose. Increased dose has also been associated with visual processing of radiographic film, which often requires repeating the radiographic examination.

Influence of physical parameters on radiation protection and image quality in intra-oral radiology

Energy Technology Data Exchange (ETDEWEB)

Belinato, W. [Instituto Federal de Ensino Basico, Tecnico e Tecnologico da Bahia, Av. Amazonas, 1350-45030-220, Zabele, Vitoria da Conquista, BA (Brazil); Departamento de Fisica, Universidade Federal de Sergipe, Av. Marechal Rondon s/n, 49100-000 Rosa Elze, Sao Cristovao, SE (Brazil); Souza, D.N., E-mail: divanizi@ufs.br [Departamento de Fisica, Universidade Federal de Sergipe, Av. Marechal Rondon s/n, 49100-000 Rosa Elze, Sao Cristovao, SE (Brazil)

2011-10-01

In the world of diagnostic imaging, radiography is an important supplementary method for dental diagnosis. In radiology, special attention must be paid to the radiological protection of patients and health professionals, and also to image quality for correct diagnosis. In Brazil, the national rules governing the operation of medical and dental radiology were specified in 1998 by the National Sanitary Surveillance Agency, complemented in 2005 by the guide 'Medical radiology: security and performance of equipment.' In this study, quality control tests were performed in public clinics with dental X-ray equipment in the State of Sergipe, Brazil, with consideration of the physical parameters that influence radiological protection and also the quality of images taken in intra-oral radiography. The accuracy of the exposure time was considered acceptable for equipment with digital timers. Exposure times and focal-spot size variations can lead to increased entrance dose. Increased dose has also been associated with visual processing of radiographic film, which often requires repeating the radiographic examination.

Investigating combined influence of petrology and technological parameters on strength of porous coke body

Energy Technology Data Exchange (ETDEWEB)

Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

1983-09-01

The VUKhIN branch in Kuznetsk investigated effects of coal petrology and coking conditions on structural strength of coke in blast furnaces. Structural strength of coke produced from black coal from the Kuzbass as well as structural strength of coke partially gasified by carbon dioxide under conditions similar to those in blast furnaces was investigated. Fourteen samples of coal mixtures from the Kuzbass were used. Regression analysis was applied. Equations for forecasting coke properties on the basis of coal petrology and selected parameters characterizing coking were derived. Analyses showed that coke structural strength was decisively influenced by coefficients which characterized the average reflectivity of vitrinite in a coal mixture and its average density. After partial coke gasification by carbon dioxide effects of coefficients which characterized coal mixture nonhomogeneity (fluctuations of vitrinite reflectivity) and coal mixture density increased. Increasing coal density partially compensated negative effects of fluctuations of vitrinite reflectivity on coke structural strength. (10 refs.) (In Russian)

Influence of the layer parameters on the performance of the CdTe solar cells

Science.gov (United States)

Haddout, Assiya; Raidou, Abderrahim; Fahoume, Mounir

2018-03-01

Influence of the layer parameters on the performances of the CdTe solar cells is analyzed by SCAPS-1D. The ZnO: Al film shows a high efficiency than SnO2:F. Moreover, the thinner window layer and lower defect density of CdS films are the factor in the enhancement of the short-circuit current density. As well, to increase the open-circuit voltage, the responsible factors are low defect density of the absorbing layer CdTe and high metal work function. For the low cost of cell production, ultrathin film CdTe cells are used with a back surface field (BSF) between CdTe and back contact, such as PbTe. Further, the simulation results show that the conversion efficiency of 19.28% can be obtained for the cell with 1-μm-thick CdTe, 0.1-μm-thick PbTe and 30-nm-thick CdS.

Review of parameters influencing the structural response of a submerged body under cavitation conditions

International Nuclear Information System (INIS)

Escaler, X; De La Torre, O; Farhat, M

2015-01-01

Submerged structures that operate under extreme flows are prone to suffer large scale cavitation attached to their surfaces. Under such conditions the added mass effects differ from the expected ones in pure liquids. Moreover, the existence of small gaps between the structure and surrounding bodies filled with fluid also influence the dynamic response. A series of experiments and numerical simulations have been carried out with a truncated NACA0009 hydrofoil mounted as a cantilever beam at the LMH-EPFL cavitation tunnel. The three first modes of vibration have been determined and analysed under various hydrodynamic conditions ranging from air and still water to partial cavitation and supercavitation. A remote nonintrusive excitation system with piezoelectric patches has been used for the experiments. The effects of the cavity properties and the lateral gap size on the natural frequencies and mode shapes have been determined. As a result, the significance of several parameters in the design of such structures is discussed. (paper)

Review of parameters influencing the structural response of a submerged body under cavitation conditions

Science.gov (United States)

Escaler, X.; De La Torre, O.; Farhat, M.

2015-12-01

Submerged structures that operate under extreme flows are prone to suffer large scale cavitation attached to their surfaces. Under such conditions the added mass effects differ from the expected ones in pure liquids. Moreover, the existence of small gaps between the structure and surrounding bodies filled with fluid also influence the dynamic response. A series of experiments and numerical simulations have been carried out with a truncated NACA0009 hydrofoil mounted as a cantilever beam at the LMH-EPFL cavitation tunnel. The three first modes of vibration have been determined and analysed under various hydrodynamic conditions ranging from air and still water to partial cavitation and supercavitation. A remote nonintrusive excitation system with piezoelectric patches has been used for the experiments. The effects of the cavity properties and the lateral gap size on the natural frequencies and mode shapes have been determined. As a result, the significance of several parameters in the design of such structures is discussed.

Contrast-enhanced 3T MR perfusion of musculoskeletal tumours. T1 value heterogeneity assessment and evaluation of the influence of T1 estimation methods on quantitative parameters

Energy Technology Data Exchange (ETDEWEB)

Gondim Teixeira, Pedro Augusto; Leplat, Christophe; Verbizier, Jacques de; Blum, Alain [Hopital Central, CHRU-Nancy, Service d' Imagerie Guilloz, Nancy (France); Chen, Bailiang; Beaumont, Marine [Universite de Lorraine, Laboratoire IADI, UMR S 947, Nancy (France); Badr, Sammy; Cotten, Anne [CHRU Lille Centre de Consultations et d' Imagerie de l' Appareil Locomoteur, Department of Radiology and Musculoskeletal Imaging, Lille (France)

2017-12-15

To evaluate intra-tumour and striated muscle T1 value heterogeneity and the influence of different methods of T1 estimation on the variability of quantitative perfusion parameters. Eighty-two patients with a histologically confirmed musculoskeletal tumour were prospectively included in this study and, with ethics committee approval, underwent contrast-enhanced MR perfusion and T1 mapping. T1 value variations in viable tumour areas and in normal-appearing striated muscle were assessed. In 20 cases, normal muscle perfusion parameters were calculated using three different methods: signal based and gadolinium concentration based on fixed and variable T1 values. Tumour and normal muscle T1 values were significantly different (p = 0.0008). T1 value heterogeneity was higher in tumours than in normal muscle (variation of 19.8% versus 13%). The T1 estimation method had a considerable influence on the variability of perfusion parameters. Fixed T1 values yielded higher coefficients of variation than variable T1 values (mean 109.6 ± 41.8% and 58.3 ± 14.1% respectively). Area under the curve was the least variable parameter (36%). T1 values in musculoskeletal tumours are significantly different and more heterogeneous than normal muscle. Patient-specific T1 estimation is needed for direct inter-patient comparison of perfusion parameters. (orig.)

Hydrogen isotopes transport parameters in fusion reactor materials

International Nuclear Information System (INIS)

Serra, E.; Ogorodnikova, O.V.

1998-01-01

This work presents a review of hydrogen isotopes-materials interactions in various materials of interest for fusion reactors. The relevant parameters cover mainly diffusivity, solubility, trap concentration and energy difference between trap and solution sites. The list of materials includes the martensitic steels (MANET, Batman and F82H-mod.), beryllium, aluminium, beryllium oxide, aluminium oxide, copper, tungsten and molybdenum. Some experimental work on the parameters that describe the surface effects is also mentioned. (orig.)

The influence of systematic pulse-limited physical exercise on the parameters of the cardiovascular system in patients over 65 years of age.

Science.gov (United States)

Chomiuk, Tomasz; Folga, Andrzej; Mamcarz, Artur

2013-04-20

The influence of physical exercise on the parameters of the cardiovascular system of elderly persons has not been sufficiently investigated yet. The aim of the study was to assess the influence of regular 6-week physical exercise using the Nordic walking (NW) method in a group of elderly persons on their physical performance and regulation of selected parameters assessing the cardiovascular system. Fifty patients over 65 years of age participated in the study. The study encompassed: medical interview, physical examination, resting ECG, spiroergometry examination, 6MWT (6-minute walk test) and 24-hour ambulatory blood pressure monitoring (ABPM). During the exercise programme, the pulse was monitored using pulsometers. After the completion of the training, check-up tests assessing the same parameters were performed. The control group consisted of 18 persons over 65 years of age with similar cardiovascular problems. In the test group, duration of the physical effort increased by 1.02 min (p = 0.0001), the maximum load increased by 10.68 W (p = 0.0001), values of VO2max by 2.10 (p = 0.0218), distance improved in 6MWT by 75.04 m (p = 0.00001), systolic blood pressure decreased by 5.50 mm Hg (p = 0.035) and diastolic blood pressure by 3.50 mm Hg (p = 0.054) as compared to the control group. Systematic NW physical exercise limited by the pulse had a beneficial effect on the physical performance of elderly persons as assessed with main parameters. A short 6-week programme of endurance exercises had a hypotensive effect in elderly persons over 65 years of age.

Design-relevant mechanical properties of 316-type stainless steels for superconducting magnets

Energy Technology Data Exchange (ETDEWEB)

Tobler, R.L.; Nishimura, A.; Yamamoto, J.

1996-08-01

Worldwide interest in austenitic alloys for structural applications in superconducting magnets has led to an expanded database for the 316-type stainless steels. We review the cryogenic mechanical properties of wrought, cast, and welded steels at liquid helium temperature (4 K), focussing on aspects of material behavior relevant to magnet design. Fracture mechanics parameters essential to structural reliability assessments are presented, including strength, toughness, and fatigue parameters that are critical for some component designs. (author). 105 refs.

Design-relevant mechanical properties of 316-type stainless steels for superconducting magnets

International Nuclear Information System (INIS)

Tobler, R.L.; Nishimura, A.; Yamamoto, J.

1996-08-01

Worldwide interest in austenitic alloys for structural applications in superconducting magnets has led to an expanded database for the 316-type stainless steels. We review the cryogenic mechanical properties of wrought, cast, and welded steels at liquid helium temperature (4 K), focussing on aspects of material behavior relevant to magnet design. Fracture mechanics parameters essential to structural reliability assessments are presented, including strength, toughness, and fatigue parameters that are critical for some component designs. (author). 105 refs

Generating three-parameter sensor

Directory of Open Access Journals (Sweden)

Filinyuk M. A.

2014-08-01

Full Text Available Generating sensors provide the possibility of getting remote information and its easy conversion into digital form. Typically, these are one-parameter sensors formed by combination of a primary transmitter (PT and a sine wave generator. Two-parameter sensors are not widely used as their implementation causes a problem with ambiguity output when measuring the PT. Nevertheless, the problem of creating miniature, thrifty multi-parameter RF sensors for different branches of science and industry remains relevant. Considering ways of designing RF sensors, we study the possibility of constructing a three-parameter microwave radio frequency range sensor, which is based on a two-stage three-parameter generalized immitance convertor (GIC. Resistive, inductive and capacitive PT are used as sensing elements. A mathematical model of the sensor, which describes the relation of the sensor parameters to the parameters of GIC and PT was developed. The basic parameters of the sensor, its transfer function and sensitivity were studied. It is shown that the maximum value of the power generated signal will be observed at a frequency of 175 MHz, and the frequency ranges depending on the parameters of the PT will be different. Research results and adequacy of the mathematical model were verified by the experiment. Error of the calculated dependences of the lasing frequency on PT parameters change, compared with the experimental data does not exceed 2 %. The relative sensitivity of the sensor based on two-stage GIC showed that for the resistive channel it is about 1.88, for the capacitive channel –1,54 and for the inductive channel –11,5. Thus, it becomes possible to increase the sensor sensitivity compared with the sensitivity of the PT almost 1,2—2 times, and by using the two stage GIC a multifunctional sensor is provided.

Influence of operating parameters on the arsenic and boron removal by electrocoagulation

International Nuclear Information System (INIS)

Can, B. Z.; Boncukcuoglu, R.; Bayar, S.; Bayhan, Y.K

2016-01-01

Despite their high boron contents, some boron deposits contain considerable amounts of arsenic. Its toxicology and health hazard also has been reported for many years. In this work arsenic and boron removal from synthetic water was studied on laboratory scale by electrocoagulation using aluminum electrodes. The influence of main operating parameters such as current density, stirring speed, supporting electrolyte type and concentration on the arsenic and boron removal was investigated. Waste water sample was prepared with initial arsenic concentration of 50 mg L/sup -1/ and boron concentration of 1000 mg L/sup -1/. Current density was varied from 0.18 to 4.28 mA cm/sup -2/, stirring speed was varied as 50, 150, 250, 350 rpm, NaCl, KCl and Na/sub 2/SO/sub 4/ were used as supporting electrolyte. The obtained experimental results showed that efficiency of arsenic and boron removal increased with increasing current density. As the current density increases, the potential difference applied to the system also increases the energy consumption. Increasing the supporting electrolyte concentration increased conductivity of solution and decreased energy consumption. The most favorable supporting electrolyte type was NaCl for arsenic and boron removal. The best stirring speed was 150 rpm for arsenic and boron removal. (author)

Influence of spray forming process parameters on the microstructure and porosity of Mg{sub 2}Si rich aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Stelling, O.; Hehl, A. von [Foundation Institute for Material Science, Bremen (Germany); Uhlenwinkel, V. [University of Bremen, FB4 FG01 Department Process and Chemcial Engineering, Bremen (Germany); Krug, P. [PEAK Werkstoff GmbH, Velbert (Germany); Ellendt, N.

2010-07-15

Due to high cooling rates spray forming is an appropriate process to produce aluminum alloys with a high content of Mg{sub 2}Si. Compared to common casting processes, a fine microstructure can be achieved yielding in improved mechanical properties. In this work, billets were spray formed from the two alloys AlMg15Si8Cu2 (22 mass-% Mg{sub 2}Si) and AlMg20.5Si11Cu2 (30 mass-% Mg{sub 2}Si) under different spraying conditions. The analysis of the microstructure showed that the size of Mg{sub 2}Si dispersoids is very sensitive to process parameters. Besides the well known thermal effects of melt superheat (carried out from -40 K to +170 K) and GMR (varied from 2.0 to 6.3) a strong influence of the scanning frequency of the atomizer nozzle (7 Hz and 15 Hz) could be observed. Similar effects could be found for the occurrence of porosity. A new parameter, the enthalpy flow to gas flow ratio (EGR), was defined from these two parameters of which correlations of Mg{sub 2}Si dispersoid size and amount of porosity were found. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Influence of tool geometry and process parameters on macrostructure and static strength in friction stir spot welded polyethylene sheets

International Nuclear Information System (INIS)

Bilici, Mustafa Kemal; Yuekler, Ahmet Irfan

2012-01-01

Highlights: → All velding parameters and different tool geometries have demonstrated a different effects on weld strength. → Friction stir spot welding of polyethylene mechanical scission is very important. → Metric screw the tool has a great influence on the weld strength of FSSW. -- Abstract: The effect of important welding parameters and tool properties that are effective on static strength in friction stir spot welds of polyethylene sheets were studied. Six different tool pin profiles (straight cylindrical, tapered cylindrical, threaded cylindrical, triangular, square and hexagonal) with different shoulder geometries, different pin length, pin angle and concavity angle were used to fabricate the joints. The tool rotational speed, tool plunge depth and dwell time were determined welding parameters. All the welding operations were done at the room temperature. Welding force and welding zone material temperature measurements were also done. Lap-shear tests were carried out to find the weld static strength. Weld cross section appearance observations were also done. From the experiments, the effect of pin profile, pin length, pin angle, dwell time and tool rotational speed on friction stir spot welding formation and weld strength was determined.

Mössbauer parameters of ordinary chondrites influenced by the fit accuracy of the troilite component: an example of Chelyabinsk LL5 meteorite

Energy Technology Data Exchange (ETDEWEB)

Maksimova, A. A. [Ural Federal University, Department of Physical Techniques and Devices for Quality Control, Institute of Physics and Technology (Russian Federation); Klencsár, Z. [Hungarian Academy of Sciences, Institute of Materials and Environmental Chemistry, Research Centre for Natural Sciences (Hungary); Oshtrakh, M. I., E-mail: oshtrakh@gmail.com; Petrova, E. V.; Grokhovsky, V. I. [Ural Federal University, Department of Physical Techniques and Devices for Quality Control, Institute of Physics and Technology (Russian Federation); Kuzmann, E.; Homonnay, Z. [Eötvös Loránd University, Institute of Chemistry (Hungary); Semionkin, V. A. [Ural Federal University, Department of Physical Techniques and Devices for Quality Control, Institute of Physics and Technology (Russian Federation)

2016-12-15

The influence of the fit accuracy of the troilite component in the Mössbauer spectra of ordinary chondrites on the parameters obtained for other spectral components was evaluated using the Mössbauer spectrum of Chelyabinsk LL5 meteorite fragment with light lithology as a typical example. It was shown that with respect to the application of a usual sextet component where quadrupole interaction is taken into account in the first-order perturbation limit, substantial improvement of the spectrum fit can be achieved either by using the full Hamiltonian description of the troilite component or by its formal approximation with the superposition of three symmetric doublet components. Parameter values obtained for the main spectral components related to olivine and pyroxene were not sensitive to the fit of troilite component while parameters of the minor spectral components depended on the way of troilite component fitting.

Estimating RASATI scores using acoustical parameters

International Nuclear Information System (INIS)

Agüero, P D; Tulli, J C; Moscardi, G; Gonzalez, E L; Uriz, A J

2011-01-01

Acoustical analysis of speech using computers has reached an important development in the latest years. The subjective evaluation of a clinician is complemented with an objective measure of relevant parameters of voice. Praat, MDVP (Multi Dimensional Voice Program) and SAV (Software for Voice Analysis) are some examples of software for speech analysis. This paper describes an approach to estimate the subjective characteristics of RASATI scale given objective acoustical parameters. Two approaches were used: linear regression with non-negativity constraints, and neural networks. The experiments show that such approach gives correct evaluations with ±1 error in 80% of the cases.

The influence of selected design and operating parameters on the dynamics of the steam micro-turbine

Science.gov (United States)

Żywica, Grzegorz; Kiciński, Jan

2015-10-01

The topic of the article is the analysis of the influence of selected design parameters and operating conditions on the radial steam micro-turbine, which was adapted to operate with low-boiling agent in the Organic Rankine Cycle (ORC). In the following parts of this article the results of the thermal load analysis, the residual unbalance and the stiffness of bearing supports are discussed. Advanced computational methods and numerical models have been used. Computational analysis showed that the steam micro-turbine is characterized by very good dynamic properties and is resistant to extreme operating conditions. The prototype of micro-turbine has passed a series of test calculations. It has been found that it can be subjected to experimental research in the micro combined heat and power system.

The influence of soil organic carbon on interactions between microbial parameters and metal concentrations at a long-term contaminated site

Energy Technology Data Exchange (ETDEWEB)

Muhlbachova, G. [Crop Research Institute, Drnovska 507, 161 06 Prague 6, Ruzyne (Czech Republic); Sagova-Mareckova, M., E-mail: sagova@vurv.cz [Crop Research Institute, Drnovska 507, 161 06 Prague 6, Ruzyne (Czech Republic); Omelka, M. [Charles University, Faculty of Mathematics and Physics, Dept. of Probability and Mathematical Statistics, Prague 8, Karlin (Czech Republic); Szakova, J.; Tlustos, P. [Czech University of Life Sciences, Department of Agroenvironmental Chemistry and Plant Nutrition, Prague 6, Suchdol (Czech Republic)

2015-01-01

The effects of lead, zinc, cadmium, arsenic and copper deposits on soil microbial parameters were investigated at a site exposed to contamination for over 200 years. Soil samples were collected in triplicates at 121 sites differing in contamination and soil organic carbon (SOC). Microbial biomass, respiration, dehydrogenase activity and metabolic quotient were determined and correlated with total and extractable metal concentrations in soil. The goal was to analyze complex interactions between toxic metals and microbial parameters by assessing the effect of soil organic carbon in the relationships. The effect of SOC was significant in all interactions and changed the correlations between microbial parameters and metal fractions from negative to positive. In some cases, the effect of SOC was combined with that of clay and soil pH. In the final analysis, dehydrogenase activity was negatively correlated to total metal concentrations and acetic acid extractable metals, respiration and metabolic quotient were to ammonium nitrate extractable metals. Dehydrogenase activity was the most sensitive microbial parameter correlating most frequently with contamination. Total and extractable zinc was most often correlated with microbial parameters. The large data set enabled robust explanation of discrepancies in organic matter functioning occurring frequently in analyzing of contaminated soil processes. - Highlights: • Soil organic carbon affected all interactions between metals and microorganisms. • Soil organic carbon adjustment changed correlations from positive to negative. • Ammonium nitrate extractable metals were the most influencing fraction. • Dehydrogenase activity was the most affected soil parameter. • Zinc was the most toxic metal among studied metals.

The influence of soil organic carbon on interactions between microbial parameters and metal concentrations at a long-term contaminated site

International Nuclear Information System (INIS)

Muhlbachova, G.; Sagova-Mareckova, M.; Omelka, M.; Szakova, J.; Tlustos, P.

2015-01-01

The effects of lead, zinc, cadmium, arsenic and copper deposits on soil microbial parameters were investigated at a site exposed to contamination for over 200 years. Soil samples were collected in triplicates at 121 sites differing in contamination and soil organic carbon (SOC). Microbial biomass, respiration, dehydrogenase activity and metabolic quotient were determined and correlated with total and extractable metal concentrations in soil. The goal was to analyze complex interactions between toxic metals and microbial parameters by assessing the effect of soil organic carbon in the relationships. The effect of SOC was significant in all interactions and changed the correlations between microbial parameters and metal fractions from negative to positive. In some cases, the effect of SOC was combined with that of clay and soil pH. In the final analysis, dehydrogenase activity was negatively correlated to total metal concentrations and acetic acid extractable metals, respiration and metabolic quotient were to ammonium nitrate extractable metals. Dehydrogenase activity was the most sensitive microbial parameter correlating most frequently with contamination. Total and extractable zinc was most often correlated with microbial parameters. The large data set enabled robust explanation of discrepancies in organic matter functioning occurring frequently in analyzing of contaminated soil processes. - Highlights: • Soil organic carbon affected all interactions between metals and microorganisms. • Soil organic carbon adjustment changed correlations from positive to negative. • Ammonium nitrate extractable metals were the most influencing fraction. • Dehydrogenase activity was the most affected soil parameter. • Zinc was the most toxic metal among studied metals

Analysis of the influence of the cutting edge geometry on parameters of the perforation process for conveyor and transmission belts

Directory of Open Access Journals (Sweden)

Wojtkowiak Dominik

2018-01-01

Full Text Available Perforated belts, which are used in vacuum conveyor belts, can have significantly different mechanical properties like strength and elasticity due to a variety of used materials and can have different thickness from very thin (0,7 mm to thick belts (6 mm. In order to design a complex machine for mechanical perforation, which can perforate whole range of belts, it is necessary to research the influence of the cutting edge geometry on the parameters of the perforation process. Three most important parameters, which describe the perforation process are the cutting force, the velocity and the temperature of the piercing punch. The results presented in this paper consider two different types of punching (a piercing punch with the punching die or with the reducer plate and different cutting edge directions, angles, diameters and material properties. Test were made for different groups of composites belts – with polyurethane and polyester fabric, polyamide core or aramid-fibre reinforced polymers. The main goal of this research is to specify effective tools and parameters of the perforation process for each group of composites belts.

The influence of survey duration on estimates of food intakes and its relevance for public health nutrition and food safety issues.

Science.gov (United States)

Lambe, J; Kearney, J; Leclercq, C; Zunft, H F; De Henauw, S; Lamberg-Allardt, C J; Dunne, A; Gibney, M J

2000-02-01

To examine the influence of food consumption survey duration on estimates of percentage consumers, mean total population intakes and intakes among consumers only and to consider its relevance for public health nutrition and food safety issues. Prospective food consumption survey. A multicentre study in five centres in the European Union-Dublin, Ghent, Helsinki, Potsdam and Rome. Teenage subjects were recruited through schools; 948 (80%) out of 1180 subjects completed the survey. 14-day food diaries were used to collect the food consumption data. For mean total population intakes, 53% of the foods had slopes significantly different to 0 (Pday), these differences were small, with 41% of foods having differences of day and a further 35% having differences of 1-5 g/day. Estimates of percentage consumers based on 3 days and 14 days were 1.9 and 3.6 times the 1-day estimate, respectively. For 72% of foods, at least 50% of non-consumers on day 1 became consumers over the subsequent 13 days. Estimates of mean consumer only intakes based on 3 days and 14 days were 53% and 32% of the 1 day value. In practical terms, survey duration influences estimates of percentage consumers and intakes among consumers only but not mean total population intakes. Awareness of this influence is important for improved interpretation of dietary data for epidemiological studies, development of food-based dietary guidelines and food chemical intakes. The Institute of European Food Studies, a non-profit research organization based in Trinity College Dublin. European Journal of Clinical Nutrition (2000) 54, 166-173

Modelling hydrodynamic parameters to predict flow assisted corrosion

International Nuclear Information System (INIS)

Poulson, B.; Greenwell, B.; Chexal, B.; Horowitz, J.

1992-01-01

During the past 15 years, flow assisted corrosion has been a worldwide problem in the power generating industry. The phenomena is complex and depends on environment, material composition, and hydrodynamic factors. Recently, modeling of flow assisted corrosion has become a subject of great importance. A key part of this effort is modeling the hydrodynamic aspects of this issue. This paper examines which hydrodynamic parameter should be used to correlate the occurrence and rate of flow assisted corrosion with physically meaningful parameters, discusses ways of measuring the relevant hydrodynamic parameter, and describes how the hydrodynamic data is incorporated into the predictive model

Some properties of 2-D dielectric-based ENG/MNG material parameters extracted using the S-parameter method

DEFF Research Database (Denmark)

Wu, Yunqiu; Arslanagic, Samel

This work presents a systematic investigation of material parameters for two-dimensional epsilon-negative (ENG) and mu-negative (MNG) materials as obtained by the scattering parameter method. The unit cell consists of infinite dielectric cylinders, their sizes and permittivities are chosen...... to enable the ENG and MNG behaviors. For the both configurations, the permittivity and the permeability is reported. Influence of several effects on the extracted material parameters is examined, including the loss inside the cylinders and the size of the unit cells...

Optimization and influence of parameter affecting the compressive strength of geopolymer concrete containing recycled concrete aggregate: using full factorial design approach

Science.gov (United States)

Krishnan, Thulasirajan; Purushothaman, Revathi

2017-07-01

There are several parameters that influence the properties of geopolymer concrete, which contains recycled concrete aggregate as the coarse aggregate. In the present study, the vital parameters affecting the compressive strength of geopolymer concrete containing recycled concrete aggregate are analyzedby varying four parameters with two levels using full factorial design in statistical software Minitab® 17. The objective of the present work is to gain an idea on the optimization, main parameter effects, their interactions and the predicted response of the model generated using factorial design. The parameters such as molarity of sodium hydroxide (8M and 12M), curing time (6hrs and 24 hrs), curing temperature (60°C and 90°C) and percentage of recycled concrete aggregate (0% and 100%) are considered. The results show that the curing time, molarity of sodium hydroxide and curing temperature were the orderly significant parameters and the percentage of Recycled concrete aggregate (RCA) was statistically insignificant in the production of geopolymer concrete. Thus, it may be noticeable that the RCA content had negligible effect on the compressive strength of geopolymer concrete. The expected responses from the generated model showed a satisfactory and rational agreement to the experimental data with the R2 value of 97.70%. Thus, geopolymer concrete comprising recycled concrete aggregate can solve the major social and environmental concerns such as the depletion of the naturally available aggregate sources and disposal of construction and demolition waste into the landfill.

Parameter extraction using global particle swarm optimization approach and the influence of polymer processing temperature on the solar cell parameters

Science.gov (United States)

Kumar, S.; Singh, A.; Dhar, A.

2017-08-01

The accurate estimation of the photovoltaic parameters is fundamental to gain an insight of the physical processes occurring inside a photovoltaic device and thereby to optimize its design, fabrication processes, and quality. A simulative approach of accurately determining the device parameters is crucial for cell array and module simulation when applied in practical on-field applications. In this work, we have developed a global particle swarm optimization (GPSO) approach to estimate the different solar cell parameters viz., ideality factor (η), short circuit current (Isc), open circuit voltage (Voc), shunt resistant (Rsh), and series resistance (Rs) with wide a search range of over ±100 % for each model parameter. After validating the accurateness and global search power of the proposed approach with synthetic and noisy data, we applied the technique to the extract the PV parameters of ZnO/PCDTBT based hybrid solar cells (HSCs) prepared under different annealing conditions. Further, we examine the variation of extracted model parameters to unveil the physical processes occurring when different annealing temperatures are employed during the device fabrication and establish the role of improved charge transport in polymer films from independent FET measurements. The evolution of surface morphology, optical absorption, and chemical compositional behaviour of PCDTBT co-polymer films as a function of processing temperature has also been captured in the study and correlated with the findings from the PV parameters extracted using GPSO approach.

Measurements of relevant parameters in the formation of clathrate hydrates by a novel experimental apparatus

Energy Technology Data Exchange (ETDEWEB)

Arca, S.; Di Profio, P.; Germani, R.; Savelli, G. [Perugia Univ., CEMIN, Perugia (Italy). Dept. of Chemistry

2008-07-01

There is a growing interest in understanding the thermodynamics and kinetics of clathrate hydrate formation. This paper presented a study that involved the design, construction, calibration, and testing of a new apparatus that could obtain as many parameters as possible in a single formation batch and that could measure unexplored clathrate hydrate parameters. The apparatus was capable of measuring equilibrium phases involving gaseous components. The paper described the conceptual design as well as the chamber, pressure line, temperature control, liquid addition line, and conductometric probe. The paper also discussed data acquisition, stirring, measurement examples, and internal illumination and video monitoring. It was concluded that refining measurements, particularly those concerning kinetic characterizations, is important in order to clarify several uncertain kinetic behaviors of clathrate hydrates. 6 refs., 16 figs.

Modeling the Influence of Process Parameters and Additional Heat Sources on Residual Stresses in Laser Cladding

Science.gov (United States)

Brückner, F.; Lepski, D.; Beyer, E.

2007-09-01

In laser cladding thermal contraction of the initially liquid coating during cooling causes residual stresses and possibly cracks. Preweld or postweld heating using inductors can reduce the thermal strain difference between coating and substrate and thus reduce the resulting stress. The aim of this work is to better understand the influence of various thermometallurgical and mechanical phenomena on stress evolution and to optimize the induction-assisted laser cladding process to get crack-free coatings of hard materials at high feed rates. First, an analytical one-dimensional model is used to visualize the most important features of stress evolution for a Stellite coating on a steel substrate. For more accurate studies, laser cladding is simulated including the powder-beam interaction, the powder catchment by the melt pool, and the self-consistent calculation of temperature field and bead shape. A three-dimensional finite element model and the required equivalent heat sources are derived from the results and used for the transient thermomechanical analysis, taking into account phase transformations and the elastic-plastic material behavior with strain hardening. Results are presented for the influence of process parameters such as feed rate, heat input, and inductor size on the residual stresses at a single bead of Stellite coatings on steel.

An unscaled parameter to measure the order of surfaces: a new surface elaboration to increase cells adhesion.

Science.gov (United States)

Bigerelle, M; Anselme, K; Dufresne, E; Hardouin, P; Iost, A

2002-08-01

We present a new parameter to quantify the order of a surface. This parameter is scale-independent and can be used to compare the organization of a surface at different scales of range and amplitude. To test the accuracy of this roughness parameter versus a hundred existing ones, we created an original statistical bootstrap method. In order to assess the physical relevance of this new parameter, we elaborated a great number of surfaces with various roughness amplitudes on titanium and titanium-based alloys using different physical processes. Then we studied the influence of the roughness amplitude on in vitro adhesion and proliferation of human osteoblasts. It was then shown that our new parameter best discriminates among the cell adhesion phenomena than others' parameters (Average roughness (Ra em leader )): cells adhere better on isotropic surfaces with a low order, provided this order is quantified on a scale that is more important than that of the cells. Additionally, on these low ordered metallic surfaces, the shape of the cells presents the same morphological aspect as that we can see on the human bone trabeculae. The method used to prepare these isotropic surfaces (electroerosion) could be undoubtedly and easily applied to prepare most biomaterials with complex geometries and to improve bone implant integration. Moreover, the new order parameter we developed may be particularly useful for the fundamental understanding of the mechanism of bone cell installation on a relief and of the formation of bone cell-material interface.

Self-Assessment of Distance Education Institutions: Identification of Parameters for Programme Assessment.

Science.gov (United States)

Rausaria, R. R.; Lele, Nalini A.

2002-01-01

Identifies and explains the parameters relevant for self-assessment and accreditation of programs in distance mode institutions. Discusses general perspectives on quality; defining quality in higher education and in open learning and distance education modes; organization structure of open universities; measurement of quality; parameters for…

D retention in Be exposed to fusion relevant mixed species D2−He plasma

Directory of Open Access Journals (Sweden)

M.J. Baldwin

2017-08-01

Full Text Available He admixture to D2 plasma incident on Be targets is used to study the influence of a fusion-ash relevant He concentration on D retention. A variation of exposure parameters such as He ion fraction: 0.02 ≤ α ≤ 0.1, exposure temperature: 330 ≤ Texp ≤ 650 K, ion-fluence: 5 × 1024 ≤ Φ ≤ 1 × 1027 m−2 and energy: 40 ≤ Ei ≤ 90 eV, are explored. Results are compared to D retention values in Be observed in D2 plasma (α=0. With α=0.1, a factor ∼3 reduction in D retention is noted for exposure at ∼300 K, but is less as Texp approaches ∼473 K, and not apparent above 473 K. The reduction is caused by the ability of He to hinder D saturation in low-release-temperature supersaturated binding states.

Influence of deposition parameters on morphological properties of biomedical calcium phosphate coatings prepared using electrostatic spray deposition

International Nuclear Information System (INIS)

Leeuwenburgh, S.C.G.; Wolke, J.G.C.; Schoonman, J.; Jansen, J.A.

2005-01-01

In order to deposit biomedical calcium phosphate (CaP) coatings with a defined surface morphology, the electrostatic spray deposition (ESD) technique was used since this technique offers the possibility to deposit ceramic coatings with a variety of surface morphologies. A scanning electron microscopical study was performed in order to investigate the influence of several deposition parameters on the final morphology of the deposited coatings. The chemical characteristics of the coatings were studied by means of X-ray diffraction and Fourier-transform infrared spectroscopy. Regarding the chemical coating properties, the results showed that the coatings can be described as crystalline carbonate apatite coatings, a crystal phase which is similar to the mineral phase of bone and teeth. The morphology of CaP coatings, deposited using the ESD technique, was strongly dependent on the deposition parameters. By changing the nozzle-to-substrate distance, the precursor liquid flow rate and the deposition temperature, coating morphologies were deposited, which varied from dense to highly porous, reticular morphologies. The formation of various morphologies was the result of an equilibrium between the relative rates of CaP solute precipitation/reaction, solvent evaporation and droplet spreading onto the substrate surface

Influence of sintering parameters in the ferroelectric properties os strontium bismuth tantalate samples obtained by oxide mixture

International Nuclear Information System (INIS)

Souza, R.R. de; Pereira, A.S.; Sousa, V.C.; Egea, J.R.J.

2012-01-01

The family of compounds layered-type perovskite, know as Aurivilius presents great alternative not only by the absence of lead in the composition, but because the polarization retention, replacing PZT in FeRAM devices. The strontium bismuth tantalate (SrBi 2 Ta 2 O 9 ) or SBT is ferroelectric material that has attracted considerable interest, since it has high fatigue resistance, supporting high hysteresis loops, with the change in polarization.Checking polarization and depolarization currents stimulated by temperature it is possible to obtain, for example, information about the nature of charges and about the activation energy for the process of dielectric relaxation. For analysis of ferroelectric properties of this compound, it is essential to obtain specimens with a relative density around 95%. Thus, it is important the optimization of the sintering process in order to obtain a ceramic body with a high densification. The influence of sintering parameters to obtain SrBi 2 Ta 2 O 9 in the polarization properties and in the microstructure of sintered samples was investigated by thermostimulated currents and electronic microscopy, respectively. Results show that variation of these parameters may cause changes in the ferroelectric properties of the material. (author)

Evaluation of the influence of parameters that determine the mean glandular dose in mammography using different detectors

International Nuclear Information System (INIS)

Costa, K.; Nogueira, M. S.

2015-10-01

Full text: Mammography is a test used for early detection of breast cancer. The mean glandular dose (MGD) is dosimetric greatness accepted as indicative of carcinogenic risk induced by ionizing radiation in the breasts of women undergoing mammography exams. MGD value is estimated from the incident air kerma (k i), associated with conversion factors which depend on the half-value layer (HVL), the breast composition and thickness compressed breast. This study aims to evaluate the influence of the parameters used to determine the MGD using different measurement detectors. Measurements were performed on a Siemens Mammomat Model 300 Nova mammography equipment; this has the combinations Anode/Filter of Mo/Mo, Mo/Rh and W/Rh. Detectors used were the ionization chamber Model 10X6-6M manufactured by Radcal Co., two solid-state detectors, one Model AGMS-M manufactured by Radcal Co. and other Model Xi Mammo manufactured by UNFORS. The detectors measures were compared and the MGD value was estimated; differences between measurements and the reference values were higher in HVL and k i parameters. The results are displayed according to other published works. (Author)

Analysis and Assessment of Parameters Shaping Methane Hazard in Longwall Areas

Directory of Open Access Journals (Sweden)

Eugeniusz Krause

2013-01-01

Full Text Available Increasing coal production concentration and mining in coal seams of high methane content contribute to its growing emission to longwall areas. In this paper, analysis of survey data concerning the assessment of parameters that influence the level of methane hazard in mining areas is presented. The survey was conducted with experts on ventilation and methane hazard in coal mines. The parameters which influence methane hazard in longwall areas were assigned specific weights (numerical values. The summary will show which of the assessed parameters have a strong, or weak, influence on methane hazard in longwall areas close to coal seams of high methane content.

Influence of Reinforcement Parameters and Ageing Time on Mechanical Behavior of Novel Al2024/SiC/Red Mud Composites Using Response Surface Methodology

Science.gov (United States)

Singh, Jaswinder; Chauhan, Amit

2017-12-01

This study investigates the mechanical behavior of aluminum 2024 matrix composites reinforced with silicon carbide and red mud particles. The hybrid reinforcements were successfully incorporated into the alloy matrix using the stir casting process. An orthogonal array based on Taguchi's technique was used to acquire experimental data for mechanical properties (hardness and impact energy) of the composites. The analysis of variance (ANOVA) and response surface methodology (RSM) techniques were used to evaluate the influence of test parameters (reinforcement ratio, particle size and ageing time). The morphological analysis of the surfaces (fractured during impact tests) was conducted to identify the failure mechanism. Finally, a confirmation experiment was performed to check the adequacy of the developed model. The results indicate that the ageing time is the most effective parameter as far as the hardness of the hybrid composites is concerned. It has also been revealed that red mud wt.% has maximum influence on the impact energy characteristics of the hybrid composites. The study concludes that Al2024/SiC/red mud hybrid composites possess superior mechanical performance in comparison to pure alloy under optimized conditions.

Influence of Femtosecond Laser Parameters and Environment on Surface Texture Characteristics of Metals and Non-Metals - State of the Art

Science.gov (United States)

Bharatish, A.; Soundarapandian, S.

2018-04-01

Enhancing the surface functionality by ultrashort pulsed laser texturing has received the considerable attention from researchers in the past few decades. Femtosecond lasers are widely adopted since it provides high repeatability and reproducibility by minimizing the heat affected zone (HAZ) and other collateral damages to a great extent. The present paper reports some recent studies being made worldwide on femtosecond laser surface texturing of metals, ceramics, polymers, semiconductors, thinfilms and advanced nanocomposites. It presents the state of the art knowledge in femtosecond laser surface texturing and the potential of this technology to improve properties in terms of biological, tribological and wetting performance. Since the texture quality and functionality are enhanced by the proper selection of appropriate laser parameters and ambient conditions for individual application, reporting the influence of laser parameters on surface texture characteristics assume utmost importance.

A study on the relevance and influence of the existing regulation and risk informed/performance based regulation

Energy Technology Data Exchange (ETDEWEB)

Cheong, B. J.; Kang, J. M.; Kim, H. S.; Koh, S. H.; Kang, D. H.; Park, C. H. [Cheju Univ., Jeju (Korea, Republic of)

2003-02-15

The goal of this study is to estimate the relevance and Influence of the Existing Regulation and the RI-PBR to the institutionalization of the regulatory system. This study reviews the current regulatory system and the status of the RI-PBR implementation of the US NRC and Korea based upon SECY Papers, Risk Informed Regulation Implementation Plan (RIRIP) of the US NRC and other domestic studies. In order to investigate the perceptions, knowledge level, ground for the regulatory change, a survey was performed to Korean nuclear utilities, researchers and regulators on the perception on the RIR. The questionnaire was composed of 50 questions regarding personal details on work experience, level of education and specific field of work ; level of knowledge on the risk informed performance based regulation (RI-PBR); the perception of the current regulation, the effectiveness, level of procedure, flexibility, dependency on the regulator and personal view, and the perception of the RI-PBR such as flexibility of regulation, introduction time and the effect of RI-PBR, safety improvement, public perception, parts of the existing regulatory system that should be changed, etc. 515 answered from all sectors of the nuclear field; utilities, engineering companies, research institutes, and regulatory bodies.

Grain filling parameters and yield components in wheat

OpenAIRE

Brdar Milka; Kobiljski Borislav; Balalić-Kraljević Marija

2006-01-01

Grain yield of wheat (Triticum aestivum L.) is influenced by number of grains per unit area and grain weight, which is result of grain filling duration and rate. The aim of the study was to investigate the relationships between grain filling parameters in 4 wheat genotypes of different earliness and yield components. Nonlinear regression estimated and observed parameters were analyzed. Rang of estimated parameters corresponds to rang of observed parameters. Stepwise MANOVA indicated that the ...

Transformational leadership: is this still relevant to clinical leaders?

Science.gov (United States)

Lo, David; McKimm, Judy; Till, Alex

2018-06-02

Transformational leadership theory has been at the centre of health-care leadership research for the past three decades, has had a tangible influence on the evolution of NHS leadership development strategies, and is still evident in current frameworks. This article provides an overview of the key concepts and weaknesses of transformational leadership theory and discusses its relevance within the context of the NHS working environment.

Influence of constructional energy-saving measures on the radon-concentration in the air in dwellings; Einfluss baulicher Energiesparmassnahmen auf die Radonkonzentration in Wohnraeumen

Energy Technology Data Exchange (ETDEWEB)

Grund, A.L.; Buermeyer, J.; Spizyn, A.; Zahradnik, I.; Grimm, V.; Grimm, G.; Gundlach, M.; Walpert, V.; Breckow, J. [Technische Hochschule Mittelhessen (THM), Giessen (Germany). Inst. fuer Medizinische Physik und Strahlenschutz (IMPS)

2015-07-01

Due to energy-saving measures the air exchange in residential houses may be reduced. In order to determine time-dependent courses the indoor radon-concentrations were measured both, before and after renovation for several weeks. In addition, the most relevant climatic conditions or indoor climate factors, as e.g. the CO{sub 2}-concentration, were measured. Verifying the renovation success, Blower-Door {sup registered} -Tests were performed, both as well before and after the renovation. Simultaneously the radon-concentration was measured. The results before and after renovation were compared with respect to seasonal parameters and the inhabitant's behavior. By investigation of the correlation coefficient the influencing parameters and the impact of the energy saving measures were analyzed. Based on the findings a model was developed to characterize the time-dependent course based on the influence quantities. The energy-saving measures at the building considerably influence the radon dynamics. Due to the denser building envelope, fresh air flows in case of underinflation caused by stack effect not only from the outside but even through the basement from the soil. Thus, by this path the radon-containing air can be transported into the dwelling's rooms as well. The influences of the users outweigh the influence of weather parameters, thus, the radonemission- rate was used for user-independent determination of the radon situation.

Influence of Process Parameters on the Quality of Aluminium Alloy EN AW 7075 Using Selective Laser Melting (SLM)

Science.gov (United States)

Kaufmann, N.; Imran, M.; Wischeropp, T. M.; Emmelmann, C.; Siddique, S.; Walther, F.

Selective laser melting (SLM) is an additive manufacturing process, forming the desired geometry by selective layer fusion of powder material. Unlike conventional manufacturing processes, highly complex parts can be manufactured with high accuracy and little post processing. Currently, different steel, aluminium, titanium and nickel-based alloys have been successfully processed; however, high strength aluminium alloy EN AW 7075 has not been processed with satisfying quality. The main focus of the investigation is to develop the SLM process for the wide used aluminium alloy EN AW 7075. Before process development, the gas-atomized powder material was characterized in terms of statistical distribution: size and shape. A wide range of process parameters were selected to optimize the process in terms of optimum volume density. The investigations resulted in a relative density of over 99%. However, all laser-melted parts exhibit hot cracks which typically appear in aluminium alloy EN AW 7075 during the welding process. Furthermore the influence of processing parameters on the chemical composition of the selected alloy was determined.

Study on orthorhombic parameters for 3D elastic full waveform inversion

KAUST Repository

Oh, Juwon

2015-08-21

For a better understanding of the influence of the parameterizations on the multi-parameter full waveform inversion (FWI) for 3D elastic orthorhombic media, we analyze the virtual sources for each cij parameter. Because the virtual sources for cij parameters can be regarded as bases of the virtual sources for other parameterizations, the insights developed here explains many of the scattering phenomena of the different parameters. The resulting radiation patterns provide insights on which parameter set is the best in the multi-parameter FWI for 3D elastic orthorhombic media. In this study, we analyze the virtual source for each cij parameter as a linear combination of several moment tensors. After that, we analyze the strain fields deformed by incident waves as momenta of the virtual source and their influences on sensitivity kernels of each cij parameter.

Study on orthorhombic parameters for 3D elastic full waveform inversion

KAUST Repository

Oh, Juwon; Alkhalifah, Tariq Ali

2015-01-01

For a better understanding of the influence of the parameterizations on the multi-parameter full waveform inversion (FWI) for 3D elastic orthorhombic media, we analyze the virtual sources for each cij parameter. Because the virtual sources for cij parameters can be regarded as bases of the virtual sources for other parameterizations, the insights developed here explains many of the scattering phenomena of the different parameters. The resulting radiation patterns provide insights on which parameter set is the best in the multi-parameter FWI for 3D elastic orthorhombic media. In this study, we analyze the virtual source for each cij parameter as a linear combination of several moment tensors. After that, we analyze the strain fields deformed by incident waves as momenta of the virtual source and their influences on sensitivity kernels of each cij parameter.

Classification of high-resolution multi-swath hyperspectral data using Landsat 8 surface reflectance data as a calibration target and a novel histogram based unsupervised classification technique to determine natural classes from biophysically relevant fit parameters

Science.gov (United States)

McCann, C.; Repasky, K. S.; Morin, M.; Lawrence, R. L.; Powell, S. L.

2016-12-01

Compact, cost-effective, flight-based hyperspectral imaging systems can provide scientifically relevant data over large areas for a variety of applications such as ecosystem studies, precision agriculture, and land management. To fully realize this capability, unsupervised classification techniques based on radiometrically-calibrated data that cluster based on biophysical similarity rather than simply spectral similarity are needed. An automated technique to produce high-resolution, large-area, radiometrically-calibrated hyperspectral data sets based on the Landsat surface reflectance data product as a calibration target was developed and applied to three subsequent years of data covering approximately 1850 hectares. The radiometrically-calibrated data allows inter-comparison of the temporal series. Advantages of the radiometric calibration technique include the need for minimal site access, no ancillary instrumentation, and automated processing. Fitting the reflectance spectra of each pixel using a set of biophysically relevant basis functions reduces the data from 80 spectral bands to 9 parameters providing noise reduction and data compression. Examination of histograms of these parameters allows for determination of natural splitting into biophysical similar clusters. This method creates clusters that are similar in terms of biophysical parameters, not simply spectral proximity. Furthermore, this method can be applied to other data sets, such as urban scenes, by developing other physically meaningful basis functions. The ability to use hyperspectral imaging for a variety of important applications requires the development of data processing techniques that can be automated. The radiometric-calibration combined with the histogram based unsupervised classification technique presented here provide one potential avenue for managing big-data associated with hyperspectral imaging.

Influence of Injection-Molding Process Parameters on Part Replication of Microstructures with Additively-Manufactured Soft Tooling Inserts WCMNM 2017 No

DEFF Research Database (Denmark)

Mischkot, Michael; Zhang, Yang; Segebrecht Gøtje, Asger

The objective of this research is to investigate the influence of injection molding parameters on the dimensional replication of microstructure surfaces in injection molding with additively manufactured soft tooling inserts in a photopolymer material. The replication degree of micropillars...... diameter and decreases the replication degree of the pillar height. A high melt temperature increases the pillar diameter independently from the pillar height. A higher injection speed affects both pillar diameter and height negatively. In addition, the study showed a significant difference...

Simulation of Drawing of Small Stainless Steel Platinum Medical Tubes--Influence of the Tool Parameters on the Forming Limit

International Nuclear Information System (INIS)

Linardon, Camille; Affagard, Jean-Sebastien; Chagnon, Gregory; Favier, Denis; Gruez, Benoit

2011-01-01

Tube cold drawing processes are used to reduce tube diameters and thickness, while pulling them through a conical converging die with or without inner plug. An accurate modelling of the material deformation and friction behaviour is required in order to well describe these processes.The study concerns a stainless steel platinum alloy. The material behaviour is characterised through tensile tests at strain rates as close as possible to the high strain rates reached during the drawing process. The results are fitted with an isotropic temperature-independent Johnson Cook constitutive equation. The modelling of floating plug drawing is performed on a ABAQUS/Explicit model. Friction coefficient is difficult to estimate with mechanical experimental tests, thus an inverse analysis is carried out to fit this parameter thanks to finite element simulation and experimental drawing tests. Drawing force measurements are recorded during the forming process. The Cockroft-Latham criterion is applied to understand the different process parameters influence on tube drawing and its accuracy for drawing process is evaluated.

Program for parameter studies of steam generators

International Nuclear Information System (INIS)

Mathisen, R.P.

1982-11-01

R2-GEN is a computer code for stationary thermal parameter studies of steam generators. The geometry and data are valid for Ringhals-2 generators. Subroutines and relevant calculations are included. The program is based on a heterogeneous flow model and some applications on tubes with varying contamination are presented. (G.B.)

Spectroscopic and thermal properties of uranium relevant to atomic schemes for laser isotope separation

International Nuclear Information System (INIS)

Ahmad, S.A.; Pandey, P.L.

1980-01-01

Spectroscopic data on uranium atom and thermal properties of uranium relevant to atomic schemes for laser isotope separation have been presented in this report. All the relevant spectroscopic data reported in literature so far, as well as some other parameters like photo-absorption cross sections, branching ratios, effects of magnetic and electric fields, evaluated using the existing data, have been presented here. Among the thermal properties, parameters like vapour pressure and number densities for U/Liquid U, U/URe 2 and U/UP systems, partition function, percentage population distribution in energy levels, thermal ionisation and velocities of uranium atom have been presented at different temperatures. Different possible collision processes are mentioned and cross-sections of U-U + charge-exchange and U + + e radiative recombination processes have been also evaluated. (author)

Contrast-enhanced 3T MR Perfusion of Musculoskeletal Tumours: T1 Value Heterogeneity Assessment and Evaluation of the Influence of T1 Estimation Methods on Quantitative Parameters.

Science.gov (United States)

Gondim Teixeira, Pedro Augusto; Leplat, Christophe; Chen, Bailiang; De Verbizier, Jacques; Beaumont, Marine; Badr, Sammy; Cotten, Anne; Blum, Alain

2017-12-01

To evaluate intra-tumour and striated muscle T1 value heterogeneity and the influence of different methods of T1 estimation on the variability of quantitative perfusion parameters. Eighty-two patients with a histologically confirmed musculoskeletal tumour were prospectively included in this study and, with ethics committee approval, underwent contrast-enhanced MR perfusion and T1 mapping. T1 value variations in viable tumour areas and in normal-appearing striated muscle were assessed. In 20 cases, normal muscle perfusion parameters were calculated using three different methods: signal based and gadolinium concentration based on fixed and variable T1 values. Tumour and normal muscle T1 values were significantly different (p = 0.0008). T1 value heterogeneity was higher in tumours than in normal muscle (variation of 19.8% versus 13%). The T1 estimation method had a considerable influence on the variability of perfusion parameters. Fixed T1 values yielded higher coefficients of variation than variable T1 values (mean 109.6 ± 41.8% and 58.3 ± 14.1% respectively). Area under the curve was the least variable parameter (36%). T1 values in musculoskeletal tumours are significantly different and more heterogeneous than normal muscle. Patient-specific T1 estimation is needed for direct inter-patient comparison of perfusion parameters. • T1 value variation in musculoskeletal tumours is considerable. • T1 values in muscle and tumours are significantly different. • Patient-specific T1 estimation is needed for comparison of inter-patient perfusion parameters. • Technical variation is higher in permeability than semiquantitative perfusion parameters.

Improved Differential Evolution Algorithm for Parameter Estimation to Improve the Production of Biochemical Pathway

Directory of Open Access Journals (Sweden)

Chuii Khim Chong

2012-06-01

Full Text Available This paper introduces an improved Differential Evolution algorithm (IDE which aims at improving its performance in estimating the relevant parameters for metabolic pathway data to simulate glycolysis pathway for yeast. Metabolic pathway data are expected to be of significant help in the development of efficient tools in kinetic modeling and parameter estimation platforms. Many computation algorithms face obstacles due to the noisy data and difficulty of the system in estimating myriad of parameters, and require longer computational time to estimate the relevant parameters. The proposed algorithm (IDE in this paper is a hybrid of a Differential Evolution algorithm (DE and a Kalman Filter (KF. The outcome of IDE is proven to be superior than Genetic Algorithm (GA and DE. The results of IDE from experiments show estimated optimal kinetic parameters values, shorter computation time and increased accuracy for simulated results compared with other estimation algorithms

Influence of Some Variable Parameters on Horizontal Elliptic Micro ...

African Journals Online (AJOL)

The study investigates the laminar flow and heat transfer characteristics in elliptic micro-channels of varying axis ratios and with internal longitudinal fins, operating in a region that is hydrodynamically and thermally fully developed; purposely to determine the effects of some salient fluid and geometry parameters such as ...

Influence of plating parameters on mechanical and microstructural properties of electroplated micro-spheres

International Nuclear Information System (INIS)

Brun, Etienne

2012-01-01

The aim of this PhD Thesis is to study the gold-copper cyanide electrochemical system and finally to realize gold-copper microspheres with a diameter of 800 μm and a thickness between 20 and 40 μm. The composition, the microstructure and the roughness of these shells must be perfectly controlled. To synthesise such a material, electrodeposition from a gold-copper alkaline cyanide bath has been chosen. Initially, the influence of the principal electrochemical parameters (temperature of the plating bath, stirring, etc.) was studied. This study showed that it is possible to realize 5 μm thick gold-copper alloys with various compositions. Actually, it was shown that the copper content of deposits varies with the applied potential. When increasing the copper content of coatings, the nucleation and growth mechanisms change. As a result, the grain size and the microhardness of the coatings are modified. An increase in the copper content reduces the grain size which increases the microhardness until a critical grain size of 6 nm. This increase of copper content also affects the microstructure: columnar, nodular even dendritic structures were observed. Then, 20 μm thick gold-copper coatings were realized using the same electrochemical parameters. As expected, these coatings were very difficult to plate because of the instability of the electro crystallization process resulting in the development of columnar and nodular structures. Moreover, for thicknesses above 10 μm, all deposits are free from copper. The microstructure change of deposits can be explained by inhibition phenomena generated by free cyanide. Actually, the reduction of gold-copper generates free cyanide at the cathode surface which inhibits the electro crystallization and promotes instantaneous nucleation. This production of free cyanide also modifies the electrolyte chemistry promoting the formation of Cu(CN)_4"3"- instead of Cu(CN)_3"2"-. Cu(CN)_4"3"- complexes have lower diffusion coefficients and

Experimental research on the influence of system parameters on the composition shift for zeotropic mixture (isobutane/pentane) in a system occurring phase change

International Nuclear Information System (INIS)

Bao, Junjiang; Zhao, Li

2016-01-01

Highlights: • The influence of system parameters on the composition shift for zeotropic mixture is studied. • Zeotropic mixture isobutane/pentane is selected as the working fluids. • Circulating composition and charge have the inverse proportion relationship. • The relationship between circulating composition and charge composition is linear. - Abstract: Zeotropic mixture can improve the performance of the thermodynamic cycle ascribed to the better temperature match during the heat transfer process with the characteristics of temperature glide during evaporation and condensing processes. Another characteristic of zeotropic mixture is composition shift. Composition shift means that the circulating composition and charge composition is different and is mainly caused by the two-phase hold-up and different solubility in lubricating oil. The existence of composition shift will affect the design and operation of thermodynamic system. The previous study gave little information about the influence of system parameters on the composition shift in a system occurring phase change. This paper mainly discuss the influence of system parameters on the composition shift for zeotropic mixture in a system occurring phase change as well as the validation of the linear relationship between the circulating composition and the charge composition and the inverse proportion relationship between the circulating composition and the charge mass found based on our previous theory study (Zhao and Bao, 2014). With isobutane and pentane as the research object, the impact of the key system parameters (hot water temperature, mass flow rate of hot water, feed pump frequency, cold water temperature and evaporator length) on composition shift are experimentally carried out. The results show that when the hot water temperature, mass flow rate of hot water and evaporator length increase and cold water temperature decreases, circulating composition will increase. For feed pump frequency, when

Optimization of surface roughness parameters in dry turning

OpenAIRE

R.A. Mahdavinejad; H. Sharifi Bidgoli

2009-01-01

Purpose: The precision of machine tools on one hand and the input setup parameters on the other hand, are strongly influenced in main output machining parameters such as stock removal, toll wear ratio and surface roughnes.Design/methodology/approach: There are a lot of input parameters which are effective in the variations of these output parameters. In CNC machines, the optimization of machining process in order to predict surface roughness is very important.Findings: From this point of view...

Determination of delta sub(18) in water from delta sub(18) in equilibrated CO2: influence of changes in experimental parameters on the equilibration process

International Nuclear Information System (INIS)

Nestler, V.; Arora, H.L.

1977-01-01

The result of an isotopic exchange reaction is expressed in terms of the isotopic abundance ratios, the fractionation factor and the atom number ratio of the reactants. The general formula is applied to the CO 2 -H 2 O system and simplified by neglecting terms small in relation to the experimental error. The influence of variations in the experimental parameters on the equilibrium is discussed. It is found that changes in temperature as well as atom number ratio will influence the equilibration process appreciably [pt

Biochemical parameters in the blood of grass snakes (Natrix natrix in ecosystems under varying degrees of anthropogenic influence

Directory of Open Access Journals (Sweden)

V. Y. Gasso

2016-09-01

Full Text Available The grass snake Natrix natrix (Linnaeus, 1758 is a partly hygrophilous species, distributed throughoutUkraine. This snake may be considered as a test object for environmental biomonitoring. Modern biochemical methods make it possible to obtain new scientific data on the effects of anthropogenic pressure on reptiles. Blood is a sensitive and informative indicator of the condition of an organism as it responds quickly to most changes in exogenous and endogenous factors, and reflects negative influences on both individual and, indirectly, populations. Changes in biochemical parameters may be used as biomarkers of the state of health of reptiles in ecosystems under varying degrees of anthropogenic pressure. Due the increase in anthropogenic influence the development and introduction of new methods of perceptual research, collection of up-to-date information and development of a database of reptile biochemical parameters have become an urgent priority. We collected mature individuals of the grass snake in floodplain ecosystems on the right bank of the Dnieper River in Dnipropetrovsk city. Grass snakes from floodplain habitats on the left bank of theSamaraRiver (O.L. Belgard Prysamarskii International Biosphere Station, Novomoskovsk district, Dnipropetrovsk province were studied as the control specimens. Our study demonstrated statistically significant differences between snakes from the study sites in the amount of albumin, urea and urea nitrogen, and inorganic phosphorus, as well as in alanine aminotransferase (ALT and alkaline phosphatise (AP activity. The amount of albumin in the blood serum of specimens from the anthropogenically transformed areas was significantly lower (by 25% than in that of the snakes caught in the control habitats. Decrease of the albumin concentration usually indicates abnormal processes in the kidneys and liver. According to the changes observed in the concentration of albumin, a corresponding increase in the albumin to

Status report [Parameters for calculation of nuclear reactions of relevance to non-energy nuclear applications

International Nuclear Information System (INIS)

Koning, A.

2008-01-01

Full text: Masses: Adopted Goriely HFB masses in TALYS as theoretical default instead of Moeller. Audi-Wapstra, Moeller and HFB masses tested formally with TALYS. Levels. Adopted latest discrete level update (2006) by Belgya (as sent by Capote) in TALYS. Tested with TALYS. Resonances. Adopted RIPL-2 D0 collection in TALYS. Tested by TALYS. Optical model. Coordinated Optical model segment for RIPL-3. Adopted Soukhovitskii CC potential as default for actinides. Covariances: Confirmed OMP parameter uncertainties from last meeting. Level density. Produced consistent set of level density parameters for CTM, BFM, GSM and HFM. Local models (per nucleus) and global models (systematics). With and without effective collective enhancement. Included and tested with TALYS Gamma-ray strength. Adopted Goriely HFB strength function tables as option (not default) in TALYS. Both formally tested and validated with TALYS. Fission. Adopted Sin-Capote WKB approximation in TALYS as option for fission calculations. Formally tested. RIPL-2/3 validation. Very extensive formal tests and validation procedures with TALYS. MONKEY code for random input files (has found RIPL errors in the past). Automatic comparison with all available EXFOR cross section data (for level density study). Started work on global parameter uncertainties (for covariances). SALTY nuclear data library (final version under construction): - 60 MeV n,g,p,d,t,h,a activation files for 1200 nuclides - 200 MeV n,g,p,d,t,h,a transport files for 250 nuclides RIPL is automatically being used by all TALYS users (and TALYS-related publications). TALYS-1.0 release in December 2007 (delay because of level densities). (author)

British Literature: Increasing Relevancy for High School Seniors through Multicultural Augmentation.

Science.gov (United States)

Kirkland, Nancy C.

A practicum aimed to increase the relevancy (to the ethnically diverse students of contemporary classrooms) of the regular high school senior English course in British literature and composition by expanding the curriculum to include selections from countries (other than the United States) influenced by the British Colonial Empire. Using a…

How do geometry-related parameters influence the clinical performance of orthodontic mini-implants? A systematic review and meta-analysis.