Calculation of tritium inventory and permeation in an INTOR like tokamak device and of its release after shut down

International Nuclear Information System (INIS)

Wienhold, P.; Waelbroeck, F.s; Winter, J.; Ali-Khan, I.

1980-12-01

The tritium inventory in the wall, its escape via permeation and its release in general are evaluated during the operation and later shut-down phases of a tokamak like INTOR by means of the PERI code. No real tritium problem arises after shut-down: simple outgasing techniques at wall temperatures Tsub(W) of approx. 500 0 C should decrease the tritium release rate down to a sufficient low level. Very serious problems are on the other hand expected to arise in the areas of inventory and permeation of tritium during the operation phase: one has the choice between e.g. operating at Tsub(W) = 350 0 C with a quasi-stationary tritium inventory of some 100 grams and a permeation flux phisub(p) approx. 1 gram/day or increasing Tsub(W) to 500 0 C, reducing the inventory down to some grams, but have then a leakage rate by permeation of 35 grams/day. For Tsub(W) = 100 0 C the tritium release into the torus will be intolerable. These figures are confirmed by preliminary measurements on Inconel 600. A suggestion is made as to how to alleviate the problem. (orig.) [de

Relativity concept inventory: Development, analysis, and results

Directory of Open Access Journals (Sweden)

J. S. Aslanides

2013-05-01

Full Text Available We report on a concept inventory for special relativity: the development process, data analysis methods, and results from an introductory relativity class. The Relativity Concept Inventory tests understanding of relativistic concepts. An unusual feature is confidence testing for each question. This can provide additional information; for example, high confidence correlated with incorrect answers suggests a misconception. A novel aspect of our data analysis is the use of Monte Carlo simulations to determine the significance of correlations. This approach is particularly useful for small sample sizes, such as ours. Our results show a gender bias that was not present in course assessment, similar to that reported for the Force Concept Inventory.

U.S./Mexico Border environmental study toxics release inventory data, 1988--1992

Energy Technology Data Exchange (ETDEWEB)

O`Brien, R.F.; LoPresti, C.A.

1996-02-01

This is a report on industrial toxic chemical releases and transfers based on information reported to the Toxics Release Inventory (TRI), a database maintained by the USEPA. This document discusses patterns of toxic chemical releases to the atmosphere, to water, to the land, and to underground injection; and transfers of toxic chemicals to Publicly Owned Treatment Works (POTW), and for disposal, treatment and other off-site transfers during the TRI reporting years 1988--1992. Geographic coverage is limited to the US side of the ``Border Area``, the geographic area situated within 100 km of the US/Mexico international boundary. A primary purpose of this study is to provide background information that can be used in the future development of potential ``indicator variables`` for tracking environmental and public health status in the Border Area in conjunction with the implementation of the North American Free Trade Agreement (NAFTA).

Inventory of LCIA selection methods for assessing toxic releases. Methods and typology report part B

DEFF Research Database (Denmark)

Larsen, Henrik Fred; Birkved, Morten; Hauschild, Michael Zwicky

method(s) in Work package 8 (WP8) of the OMNIITOX project. The selection methods and the other CRS methods are described in detail, a set of evaluation criteria are developed and the methods are evaluated against these criteria. This report (Deliverable 11B (D11B)) gives the results from task 7.1d, 7.1e......This report describes an inventory of Life Cycle Impact Assessment (LCIA) selection methods for assessing toxic releases. It consists of an inventory of current selection methods and other Chemical Ranking and Scoring (CRS) methods assessed to be relevant for the development of (a) new selection...... and 7.1f of WP 7 for selection methods. The other part of D11 (D11A) is reported in another report and deals with characterisation methods. A selection method is a method for prioritising chemical emissions to be included in an LCIA characterisation of toxic releases, i.e. calculating indicator scores...

The Relationship between Toxics Release Inventory Discharges and Mortality Rates in Rural and Urban Areas of the United States

Science.gov (United States)

Hendryx, Michael; Fedorko, Evan

2011-01-01

Background: Potential environmental exposures from chemical manufacturing or industrial sites have not been well studied for rural populations. The current study examines whether chemical releases from facilities monitored through the Toxics Release Inventory (TRI) program are associated with population mortality rates for both rural and urban…

1997 toxic chemical release inventory. Emergency Planning and Community Right-To-Know Act, Section 313

International Nuclear Information System (INIS)

Zaloudek, D.E.

1998-01-01

Two listed toxic chemicals were used at the Hanford Site above established activity thresholds: phosphoric acid and chlorine. Because total combined quantities of chlorine released, disposed, treated, recovered through recycle operations, co-combusted for energy recovery, and transferred to off-site locations for the purpose of recycle, energy recovery, treatment, and/or disposal, amounted to less than 500 pounds, the Hanford Site qualified for the alternate one million pound threshold for chlorine. Accordingly, this Toxic Chemical Release Inventory includes a Form A for chlorine, and a Form B for phosphoric acid

Exploring Environmental Inequity in South Korea: An Analysis of the Distribution of Toxic Release Inventory (TRI Facilities and Toxic Releases

Directory of Open Access Journals (Sweden)

D. K. Yoon

2017-10-01

Full Text Available Recently, location data regarding the Toxic Release Inventory (TRI in South Korea was released to the public. This study investigated the spatial patterns of TRIs and releases of toxic substances in all 230 local governments in South Korea to determine whether spatial clusters relevant to the siting of noxious facilities occur. In addition, we employed spatial regression modeling to determine whether the number of TRI facilities and the volume of toxic releases in a given community were correlated with the community’s socioeconomic, racial, political, and land use characteristics. We found that the TRI facilities and their toxic releases were disproportionately distributed with clustered spatial patterning. Spatial regression modeling indicated that jurisdictions with smaller percentages of minorities, stronger political activity, less industrial land use, and more commercial land use had smaller numbers of toxic releases, as well as smaller numbers of TRI facilities. However, the economic status of the community did not affect the siting of hazardous facilities. These results indicate that the siting of TRI facilities in Korea is more affected by sociopolitical factors than by economic status. Racial issues are thus crucial for consideration in environmental justice as the population of Korea becomes more racially and ethnically diverse.

Executive Order 12898 and Social, Economic, and Sociopolitical Factors Influencing Toxic Release Inventory Facility Location in EPA Region 6: A Multi-Scale Spatial Assessment of Environmental Justice

Science.gov (United States)

Moore, Andrea Lisa

2013-01-01

Toxic Release Inventory facilities are among the many environmental hazards shown to create environmental inequities in the United States. This project examined four factors associated with Toxic Release Inventory, specifically, manufacturing facility location at multiple spatial scales using spatial analysis techniques (i.e., O-ring statistic and…

Inventory Abstraction

International Nuclear Information System (INIS)

Leigh, C.

2000-01-01

The purpose of the inventory abstraction as directed by the development plan (CRWMS M and O 1999b) is to: (1) Interpret the results of a series of relative dose calculations (CRWMS M and O 1999c, 1999d). (2) Recommend, including a basis thereof, a set of radionuclides that should be modeled in the Total System Performance Assessment in Support of the Site Recommendation (TSPA-SR) and the Total System Performance Assessment in Support of the Final Environmental Impact Statement (TSPA-FEIS). (3) Provide initial radionuclide inventories for the TSPA-SR and TSPA-FEIS models. (4) Answer the U.S. Nuclear Regulatory Commission (NRC)'s Issue Resolution Status Report ''Key Technical Issue: Container Life and Source Term'' (CLST IRSR) (NRC 1999) key technical issue (KTI): ''The rate at which radionuclides in SNF [Spent Nuclear Fuel] are released from the EBS [Engineered Barrier System] through the oxidation and dissolution of spent fuel'' (Subissue 3). The scope of the radionuclide screening analysis encompasses the period from 100 years to 10,000 years after the potential repository at Yucca Mountain is sealed for scenarios involving the breach of a waste package and subsequent degradation of the waste form as required for the TSPA-SR calculations. By extending the time period considered to one million years after repository closure, recommendations are made for the TSPA-FEIS. The waste forms included in the inventory abstraction are Commercial Spent Nuclear Fuel (CSNF), DOE Spent Nuclear Fuel (DSNF), High-Level Waste (HLW), naval Spent Nuclear Fuel (SNF), and U.S. Department of Energy (DOE) plutonium waste. The intended use of this analysis is in TSPA-SR and TSPA-FEIS. Based on the recommendations made here, models for release, transport, and possibly exposure will be developed for the isotopes that would be the highest contributors to the dose given a release to the accessible environment. The inventory abstraction is important in assessing system performance because

1992 Toxic Chemical Release Inventory: Emergency Planning and Community Right-To-Know-Act of 1986 Section 313

International Nuclear Information System (INIS)

1993-07-01

Section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 (EPCRA) requires the annual submittal of toxic chemical release information to the US Environmental Protection Agency (EPA). The following document is the July 1993 submittal of the EPCRA Toxic Chemical Release Inventory Report (Form R). Included is a Form R for chlorine and for lead, the two chemicals used in excess of the established regulatory thresholds at the Hanford Site by the US Department of Energy, Richland Operations Office and its contractors during calendar year 1992

INVENTORY ABSTRACTION

International Nuclear Information System (INIS)

Ragan, G.

2001-01-01

The purpose of the inventory abstraction, which has been prepared in accordance with a technical work plan (CRWMS M andO 2000e for/ICN--02 of the present analysis, and BSC 2001e for ICN 03 of the present analysis), is to: (1) Interpret the results of a series of relative dose calculations (CRWMS M andO 2000c, 2000f). (2) Recommend, including a basis thereof, a set of radionuclides that should be modeled in the Total System Performance Assessment in Support of the Site Recommendation (TSPA-SR) and the Total System Performance Assessment in Support of the Final Environmental Impact Statement (TSPA-FEIS). (3) Provide initial radionuclide inventories for the TSPA-SR and TSPA-FEIS models. (4) Answer the U.S. Nuclear Regulatory Commission (NRC)'s Issue Resolution Status Report ''Key Technical Issue: Container Life and Source Term'' (CLST IRSR) key technical issue (KTI): ''The rate at which radionuclides in SNF [spent nuclear fuel] are released from the EBS [engineered barrier system] through the oxidation and dissolution of spent fuel'' (NRC 1999, Subissue 3). The scope of the radionuclide screening analysis encompasses the period from 100 years to 10,000 years after the potential repository at Yucca Mountain is sealed for scenarios involving the breach of a waste package and subsequent degradation of the waste form as required for the TSPA-SR calculations. By extending the time period considered to one million years after repository closure, recommendations are made for the TSPA-FEIS. The waste forms included in the inventory abstraction are Commercial Spent Nuclear Fuel (CSNF), DOE Spent Nuclear Fuel (DSNF), High-Level Waste (HLW), naval Spent Nuclear Fuel (SNF), and U.S. Department of Energy (DOE) plutonium waste. The intended use of this analysis is in TSPA-SR and TSPA-FEIS. Based on the recommendations made here, models for release, transport, and possibly exposure will be developed for the isotopes that would be the highest contributors to the dose given a release

1998 Toxic Chemical Release Inventory Report for the Emergency Planning and Community Right-to-Know Act of 1986, Title III

International Nuclear Information System (INIS)

Stockton, Marjorie B.

1999-01-01

The Emergency Planning and Community Right-to-Know Act (EPCRA) of 1986 [also known as the Superfund Amendment and Reauthorization Act (SARA), Title III], as modified by Executive Order 12856, requires that all federal facilities evaluate the need to submit an annual Toxic Chemical Release Inventory report as prescribed in Title III, Section 313 of this Act. This annual report is due every July for the preceding calendar year. Owners and operators who manufacture, process, or otherwise use certain toxic chemicals above listed threshold quantities are required to report their toxic chemical releases to all environmental mediums (air, water, soil, etc.). At Los Alamos National Laboratory (LANL), no EPCRA Section 313 chemicals were used in 1998 above the reportable threshold limits of 10,000 lb or 25,000 lb. Therefore LANL was not required to submit any Toxic Chemical Release Inventory reports (Form Rs) for 1998. This document was prepared to provide a detailed description of the evaluation on chemical usage and EPCRA Section 313 threshold determinations for LANL for 1998

An Evaluation of a Fission Product Inventory for CANDU Fuels

International Nuclear Information System (INIS)

Jung, Jong Yeob; Park, Joo Hwan

2007-01-01

Fission products are released by two processes when a single channel accident occurs. One is a 'prompt release' and the other is a 'delayed release'. Prompt release assumes that the gap inventory of the fuel elements is released by a fuel element failure at the time of an accident. Delayed release assumes that the inventories within the grain or at the grain boundary are released after a accident due to a diffusion through grains, an oxidation of the fuel and an interaction between the fuel and the Zircaloy sheath. Therefore, the calculation of a fission product inventory and its distribution in a fuel during a normal operating is the starting point for the assessment of a fission product release for single channel accidents. In this report, the fission product inventories and their distributions within s fuel under a normal operating condition are evaluated for three types of CANDU fuels such as the 37 element fuel, CANFLEX-NU and CANFLEX-RU fuel bundles in the 'limiting channel'. To accomplish the above mentioned purposes, the basic power histories for each type of CANDU fuel were produced and the fission product inventories were calculated by using the ELESTRES code

1995 Toxic chemical release inventory: Emergency Planning and Community Right-to-Know Act of 1986, Section 313

International Nuclear Information System (INIS)

Mincey, S.L.

1996-08-01

Section 313 of the Emergency Planning and Community Right-To-Know Act (EPCRA) requires the annual submittal of toxic chemical release information to the U.S. Environmental Protection Agency.Executive Order 12856, 'Federal Compliance With Right-to-Know Laws and Pollution Prevention Requirements' extends the requirements of EPCRA to all Federal agencies. The following document is the August 1996 submittal of the Hanford Site Toxic Chemical Release Inventory report. Included is a Form R for ethylene glycol, the sole chemical used in excess of the established regulatory thresholds at the Hanford Site by the U.S. Department of Energy, Richland Operations Office and its contractors during Calendar Year 1995

7 CFR 930.57 - Secondary inventory reserve.

Science.gov (United States)

2010-01-01

... shall retain control over the release of any cherries from the secondary inventory reserve. No cherries... 7 Agriculture 8 2010-01-01 2010-01-01 false Secondary inventory reserve. 930.57 Section 930.57... Handling Regulations § 930.57 Secondary inventory reserve. (a) In the event the inventory reserve...

2015 TRI National Analysis: Toxics Release Inventory Releases at Various Summary Levels

Science.gov (United States)

The TRI National Analysis is EPA's annual interpretation of TRI data at various summary levels. It highlights how toxic chemical wastes were managed, where toxic chemicals were released and how the 2015 TRI data compare to data from previous years. This dataset reports US state, county, large aquatic ecosystem, metro/micropolitan statistical area, and facility level statistics from 2015 TRI releases, including information on: number of 2015 TRI facilities in the geographic area and their releases (total, water, air, land); population information, including populations living within 1 mile of TRI facilities (total, minority, in poverty); and Risk Screening Environmental Indicators (RSEI) model related pounds, toxicity-weighted pounds, and RSEI score. The source of administrative boundary data is the 2013 cartographic boundary shapefiles. Location of facilities is provided by EPA's Facility Registry Service (FRS). Large Aquatic Ecosystems boundaries were dissolved from the hydrologic unit boundaries and codes for the United States, Puerto Rico, and the U.S. Virgin Islands. It was revised for inclusion in the National Atlas of the United States of America (November 2002), and updated to match the streams file created by the USGS National Mapping Division (NMD) for the National Atlas of the United States of America.

Amoco/Environmental Protection Agency Pollution Prevention Project, Yorktown refinery. Refinery release inventory. Final report

International Nuclear Information System (INIS)

Klee, H.; Kizier, G.J.; Baloo, S.; Hockman, E.L.; Couzens-Roberts, C.

1992-07-01

The report volume summarizes physical data obtained during a 2-year pollution prevention study of Amoco Oil Company's Yorktown Virginia Refinery. The study was jointly sponsored as a cooperative effort of Amoco Corporation and the United States Environmental Protection Agency. A multi-media sampling program was used to identify potential pollution sources within the Refinery. Sampling and analysis included air, surface water, groundwater, and solid waste data. Public perceptions about environmental issues of concern in the vicinity of the Refinery were also surveyed. The inventory showed that nearly 99 percent of the releases were airborne at the facility. Most of the remainder involved land disposal of solid wastes. Specific sources of major pollutants are identified

Licensed-fuel-facility status report, inventory difference data January 1981-June 1981

International Nuclear Information System (INIS)

1982-07-01

NRC is committed to the periodic release of inventory difference data from the licensed fuel facilities after the agency has had an opportunity to review the data and has performed any related investigations associated with the data. Information included in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233

Effects of sorption hysteresis on radionuclide releases from waste packages

International Nuclear Information System (INIS)

Barney, G.S.; Reed, D.T.

1985-01-01

A one-dimensional, numerical transport model was used to calculate radionuclide releases from waste packages emplaced in a nuclear waste repository in basalt. The model incorporates both sorption and desorption isotherm parameters measured previously for sorption of key radionuclides on the packing material component of the waste package. Sorption hysteresis as described by these isotherms lowered releases of some radionuclides by as much as two orders of magnitude. Radionuclides that have low molar inventories (relative to uranium), high solubility, and strongly sorbed, are most affected by sorption hysteresis. In these cases, almost the entire radionuclide inventory is sorbed on the packing material. The model can be used to help optimize the thickness of the packing material layer by comparing release rate versus packing material thickness curves with Nuclear Regulatory Commission (NRC) and Environmental Protection Agency (EPA) release limits

The Fertility Problem Inventory: measuring perceived infertility-related stress.

Science.gov (United States)

Newton, C R; Sherrard, W; Glavac, I

1999-07-01

To develop a reliable, valid instrument to evaluate perceived infertility-related stress. Prospective study. University-affiliated teaching hospital. Consecutively referred patients (1,153 women and 1,149 men) seen for infertility treatment. None. Participants' infertility-related stress was assessed by written questionnaire using the Fertility Problem Inventory. Current levels of anxiety, depression, and marital satisfaction also were determined. Women described greater global stress than men and higher specific stress in terms of social concerns, sexual concerns, and need for parenthood. Both men and women facing male infertility reported higher global stress and more social and sexual concerns than men and women experiencing female infertility. Social, sexual, and relationship concerns related to infertility were more effective predictors of depression and marital dissatisfaction than expressed needs for parenthood or attitudes toward child-free living. The Fertility Problem Inventory provides a reliable measure of perceived infertility-related stress and specific information on five separate domains of patient concern. Patterns of infertility-related stress differed depending on gender, fertility history, and infertility diagnosis. Among patients receiving treatment, social, sexual, and relationship concerns appear central to current distress. Counseling interventions that target these domains appear likely to offer maximal therapeutic benefit.

Relative Release-to-Birth Indicators for Investigating TRISO Fuel Fission Gas Release Models

International Nuclear Information System (INIS)

Harp, Jason M.; Hawari, Ayman I.

2008-01-01

TRISO microsphere fuel is the fundamental fuel unit for Very High Temperature Reactors (VHTR). A single TRISO particle consists of an inner kernel of uranium dioxide or uranium oxycarbide surrounded by layers of pyrolytic carbon and silicon carbide. If the silicon carbide layer fails, fission products, especially the noble fission gases Kr and Xe, will begin to escape the failed particle. The release of fission gas is usually quantified by measuring the ratio of the released activity (R) to the original birth activity (B), which is designated as the R/B ratio. In this work, relative Release-to-Birth indicators (I) are proposed as a technique for interpreting the results of TRISO irradiation experiments. By implementing a relative metric, it is possible to reduce the sensitivity of the indicators to instrumental uncertainties and variations in experimental conditions. As an example, relative R/B indicators are applied to the interpretation of representative data from the Advanced Gas Reactor-1 TRISO fuel experiment that is currently taking place at the Advanced Test Reactor of Idaho National Laboratory. It is shown that the comparison of measured to predicted relative R/B indicators (I) gives insight into the physics of release and helps validate release models. Different trends displayed by the indicators are related to the mechanisms of fission gas release such as diffusion and recoil. The current analysis shows evidence for separate diffusion coefficients for Kr and Xe and supports the need to account for recoil release. (authors)

Automated Inventory Control System for Nigeria Power Holding ...

African Journals Online (AJOL)

The company may want to release some capital from its inventory investment by reducing stock levels. In addition, manual ways of handling inventory has failed to cope with factors like ... graphical interface ability for decision making.

2004 Toxic Chemical Release Inventory Report for the Emergency Planning and Community Right-to-Know Act of 1986, Title III, Section 313

Energy Technology Data Exchange (ETDEWEB)

M. Stockton

2006-01-15

Section 313 of Emergency Planning and Community Right-to-Know Act (EPCRA) specifically requires facilities to submit a Toxic Chemical Release Inventory Report (Form R) to the U.S. Environmental Protection Agency (EPA) and state agencies if the owners and operators manufacture, process, or otherwise use any of the listed toxic chemicals above listed threshold quantities. EPA compiles this data in the Toxic Release Inventory database. Form R reports for each chemical over threshold quantities must be submitted on or before July 1 each year and must cover activities that occurred at the facility during the previous year. For reporting year 2004, Los Alamos National Laboratory (LANL or the Laboratory) submitted Form R reports for lead compounds, nitric acid, and nitrate compounds as required under the EPCRA Section 313. No other EPCRA Section 313 chemicals were used in 2004 above the reportable thresholds. This document provides a description of the evaluation of EPCRA Section 313 chemical use and threshold determinations for LANL for calendar year 2004, as well as background information about data included on the Form R reports.

Predicted radionuclide release from reactor-related unenclosed solid objects dumped in the Sea of Japan and the Pacific Ocean, east coast of Kamchatka

International Nuclear Information System (INIS)

Mount, M.E.; Lynn, N.M.; Warden, J.M.

1996-06-01

Between 1978 and 1991 reactor-related solid radioactive waste was dumped by the former Soviet Union as unenclosed objects in the Pacific Ocean, east coast of Kamchatka, and the Sea of Japan. This paper presented estimates for the current (1994) inventory of activation and corrosion products contained in the reactor-related unenclosed solid objects. In addition, simple models derived for prediction of radionuclide release from marine reactors dumped in the Kara Sea are applied to certain of the dumped objects to provide estimates of radionuclide release to the Pacific Ocean, east coast of Kamchatka, and Sea of Japan environments. For the Pacific Ocean, east coast of Kamchatka, total release rates start below 0.01 GBq yr -1 and over 1,000 years, fall to 100 Bq yr -1 . In the Sea of Japan, the total release rate starts just above 1 GBq yr - 1 , dropping off to a level less than 0.1 GBq yr -1 , extending past the year 4,000

Estimating dead wood during national forest inventories: a review of inventory methodologies and suggestions for harmonization.

Science.gov (United States)

Woodall, Christopher W; Rondeux, Jacques; Verkerk, Pieter J; Ståhl, Göran

2009-10-01

Efforts to assess forest ecosystem carbon stocks, biodiversity, and fire hazards have spurred the need for comprehensive assessments of forest ecosystem dead wood (DW) components around the world. Currently, information regarding the prevalence, status, and methods of DW inventories occurring in the world's forested landscapes is scattered. The goal of this study is to describe the status, DW components measured, sample methods employed, and DW component thresholds used by national forest inventories that currently inventory DW around the world. Study results indicate that most countries do not inventory forest DW. Globally, we estimate that about 13% of countries inventory DW using a diversity of sample methods and DW component definitions. A common feature among DW inventories was that most countries had only just begun DW inventories and employ very low sample intensities. There are major hurdles to harmonizing national forest inventories of DW: differences in population definitions, lack of clarity on sample protocols/estimation procedures, and sparse availability of inventory data/reports. Increasing database/estimation flexibility, developing common dimensional thresholds of DW components, publishing inventory procedures/protocols, releasing inventory data/reports to international peer review, and increasing communication (e.g., workshops) among countries inventorying DW are suggestions forwarded by this study to increase DW inventory harmonization.

Design options to minimize tritium inventories at Savannah River

Energy Technology Data Exchange (ETDEWEB)

Klein, J.E., E-mail: james.klein@srnl.doe.gov; Wilson, J.; Heroux, K.J.; Poore, A.S.; Babineau, D.W.

2016-11-01

Highlights: • La-Ni-Al alloys are used as tritium storage materials and retain He-3. • La-Ni-Al He-3 effects decrease useable process tritium inventory. • Use of Pd or depleted uranium beds decreases process tritium inventories. • Reduced inventory tritium facilities will lower public risk. - Abstract: Large quantities of tritium are stored and processed at the Savannah River Site (SRS) Tritium Facilities. In many design basis accidents (DBAs), it is assumed the entire tritium inventory of the in-process vessels are released from the facility and the site for inclusion in public radiological dose calculations. Pending changes in public dose calculation methodologies are driving the need for smaller in-process tritium inventories to be released during DBAs. Reducing the in-process tritium inventory will reduce the unmitigated source term for public dose calculations and will also reduce the production demand for a lower inventory process. This paper discusses process design options to reduce in-process tritium inventories. A Baseline process is defined to illustrate the impact of removing or replacing La-Ni-Al alloy tritium storage beds with palladium (Pd) or depleted uranium (DU) storage beds on facility in-process tritium inventories. Elimination of La-Ni-Al alloy tritium storage beds can reduce in-process tritium inventories by over 1.5 kg, but alternate process technologies may needed to replace some functions of the removed beds.

Design options to minimize tritium inventories at Savannah River

International Nuclear Information System (INIS)

Klein, J.E.; Wilson, J.; Heroux, K.J.; Poore, A.S.; Babineau, D.W.

2016-01-01

Highlights: • La-Ni-Al alloys are used as tritium storage materials and retain He-3. • La-Ni-Al He-3 effects decrease useable process tritium inventory. • Use of Pd or depleted uranium beds decreases process tritium inventories. • Reduced inventory tritium facilities will lower public risk. - Abstract: Large quantities of tritium are stored and processed at the Savannah River Site (SRS) Tritium Facilities. In many design basis accidents (DBAs), it is assumed the entire tritium inventory of the in-process vessels are released from the facility and the site for inclusion in public radiological dose calculations. Pending changes in public dose calculation methodologies are driving the need for smaller in-process tritium inventories to be released during DBAs. Reducing the in-process tritium inventory will reduce the unmitigated source term for public dose calculations and will also reduce the production demand for a lower inventory process. This paper discusses process design options to reduce in-process tritium inventories. A Baseline process is defined to illustrate the impact of removing or replacing La-Ni-Al alloy tritium storage beds with palladium (Pd) or depleted uranium (DU) storage beds on facility in-process tritium inventories. Elimination of La-Ni-Al alloy tritium storage beds can reduce in-process tritium inventories by over 1.5 kg, but alternate process technologies may needed to replace some functions of the removed beds.

Superfund and Toxic Release Inventory Sites - MDC_ContaminatedSite

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — A point feature class of open DERM Contaminated sites - see phase code for status of site. Contaminated sites identifies properties where environmental contamination...

Inventory of radioactive corrosion products on the primary surfaces and release during shutdown in Ringhals 2

International Nuclear Information System (INIS)

Aronsson, O.

1994-01-01

In Ringhals 2 a retrospective study using gamma scans of system surfaces, fuel crud sampling and reactor coolant analyses during operation and shutdown has been done. The data have been used to prepare a balance of activity inventory. The inventory has been fairly stable from 1986 to 1993, expressed as a gamma source term. The steam generator replacement in 1989 removed some 40-50% of the Co-60 inventory in the reactor system. After the steam generator replacement, the gamma source term has got an increasing contribution from Co-58, absolutely as well as relatively. The reason for this is probably the switch from high pH operation to modified pH operation. Corrosion from fresh alloy 690 surfaces in the new steam generators is probably another contributing factor. The inventory and production rate of Co-60 is decreasing over the years. It has also been found that clean-up of the reactor coolant during start-up, operation, and shutdown as well as the fuel pool during refuelling removes about the same amounts of Co-60. (author). 11 figs., 15 refs

78 FR 13743 - Department of State FY11 Service Contract Inventory

Science.gov (United States)

2013-02-28

... DEPARTMENT OF STATE [Public Notice 8207] Department of State FY11 Service Contract Inventory... Contract Inventory. SUMMARY: The Department of State has publically released its Service Contract Inventory... Act, Public Law 111-117, requires Department of State, and other civilian agencies, to submit an...

77 FR 5614 - Department of State FY11 Service Contract Inventory

Science.gov (United States)

2012-02-03

... DEPARTMENT OF STATE [Public Notice 7785] Department of State FY11 Service Contract Inventory... Contract Inventory. SUMMARY: The Department of State has publically released its Service Contract Inventory.../ . Section 743 of Division C of the FY 2010 Consolidated Appropriations Act, Public Law 111-117, requires...

Trauma Related Guilt Inventory - psychometric properties of the Polish adaptation (TRGI-PL).

Science.gov (United States)

Popiel, Agnieszka; Zawadzki, Bogdan

2015-01-01

AIM : Although various aspects of guilt are frequent problems of patients suffering from PTSD, they have been included into the diagnostic criteria for PTSD just in the present version DSM-5. Kubany proposed a cognitive conceptualization of guilt in PTSD followed by development of the Trauma Related Guilt Inventory (TRGI). The aim of the paper is to present psychometric properties of the Polish version of the inventory - the TRGI-PL. A Polish adaptation of the Trauma-Related Guilt Inventory was applied to a sample of 280 motor vehicle (MVA) participants (147 females, 133 males of age from 18 to 80 (M=34,93, SD=13,71) within 1-24 months after a MVA (M=10,18, SD=6,23). Validation of the Polish version was done by analyzing the internal structure of the instrument and comparing the emotional and cognitive aspects of guilt assessed by the TRGI with PTSD symptoms, post-traumatic cognitions and responsibility for MVA and subjective agreement with the judgment. The model with four latent factors: Distress, Hindsight-Bias/Responsibility, Wrongdoing and Insufficient Justification scales showed acceptable fit (Satorra-Bentler chi2=518,62, df=203, pguilt, obtained in the studies on original TRGI version. Reliability coefficients are similar to original version. Correlations with other PTSD measures showed satisfactory convergent and discriminative validity. The Polish adaptation of the Trauma-Related Guilt Inventory is a reliable and valid tool for assessing guilt as a multidimensional phenomenon, comprising emotional and several cognitive characteristics, in trauma survivors.

76 FR 9399 - Department of State FY10 Service Contract Inventory

Science.gov (United States)

2011-02-17

... DEPARTMENT OF STATE [Public Notice 7321] Department of State FY10 Service Contract Inventory... Contract Inventory. SUMMARY: The Department of State has publically released its Service Contract Inventory for FY10. Section 743 of Division C of the FY 2010 Consolidated Appropriations Act, Public Law 111-117...

Tellurium release and deposition during the TMI-2 accident

International Nuclear Information System (INIS)

Vinjamuri, K.; Osetek, D.J.; Hobbins, R.R.; Jessup, J.S.

1984-09-01

The estimated behavior of tellurium during and after the accident at the Three Mile Island Unit-2 is presented. The behavior is based on all available measurement data for /sup 129m/Te, 132 Te, stable tellurium ( 126 Te, 128 Te and 130 Te), and best estimate calculations of tellurium release and transport. The predicted release was calculated using current techniques that relate release rate to fuel temperature and holdup of tellurium in zircaloy until significant oxidation occurs. The calculated release fraction was low, approx. 7%, but the total measured release for samples analyzed to date is about 5.8%. Of the measured tellurium about 2.4, 1.8, 0.88, 0.42, 0.17 and 0.086% of core inventory were in the containment sump water, upper plenum assembly surfaces, containment solids in the sump water, makeup and purification demineralizer, containment inside surface, and the reactor primary coolant, respectively. A significant fraction (54%) of the tellurium calculated to be retained on the upper plenum surfaces (4.61% of the core inventory) was deposited during the high pressure injection of coolant at about 200 min after the reactor scram. Comparison of tellurium behavior with in-pile and out-of-pile tests strongly suggests that zircaloy holds tellurium until significant cladding oxidation occurs

Tritium transport and release from lithium ceramic breeder materials

International Nuclear Information System (INIS)

Johnson, C.E.; Kopasz, J.P.; Tam, S.W.

1994-01-01

In an operating fusion reactor,, the tritium breeding blanket will reach a condition in which the tritium release rate equals the production rate. The tritium release rate must be fast enough that the tritium inventory in the blanket does not become excessive. Slow tritium release will result in a large tritium inventory, which is unacceptable from both economic and safety viewpoints As a consequence, considerable effort has been devoted to understanding the tritium release mechanism from ceramic breeders and beryllium neutron multipliers through theoretical, laboratory, and in-reactor studies. This information is being applied to the development of models for predicting tritium release for various blanket operating conditions

User Instructions for the Systems Assessment Capability, Rev. 0, Computer Codes Volume 1: Inventory, Release, and Transport Modules

International Nuclear Information System (INIS)

Eslinger, Paul W.; Engel, David W.; Gerhardstein, Lawrence H.; Lopresti, Charles A.; Nichols, William E.; Strenge, Dennis L.

2001-12-01

One activity of the Department of Energy's Groundwater/Vadose Zone Integration Project is an assessment of cumulative impacts from Hanford Site wastes on the subsurface environment and the Columbia River. Through the application of a system assessment capability (SAC), decisions for each cleanup and disposal action will be able to take into account the composite effect of other cleanup and disposal actions. The SAC has developed a suite of computer programs to simulate the migration of contaminants (analytes) present on the Hanford Site and to assess the potential impacts of the analytes, including dose to humans, socio-cultural impacts, economic impacts, and ecological impacts. The general approach to handling uncertainty in the SAC computer codes is a Monte Carlo approach. Conceptually, one generates a value for every stochastic parameter in the code (the entire sequence of modules from inventory through transport and impacts) and then executes the simulation, obtaining an output value, or result. This document provides user instructions for the SAC codes that handle inventory tracking, release of contaminants to the environment, and transport of contaminants through the unsaturated zone, saturated zone, and the Columbia River

An Improved Inventory Control Model for the Brazilian Navy Supply System

Science.gov (United States)

2001-12-01

Portuguese Centro de Controle de Inventario da Marinha, the Brazilian Navy Inventory Control Point (ICP) developed an empirical model called SPAADA...NAVAL POSTGRADUATE SCHOOL Monterey, California THESIS Approved for public release; distribution is unlimited AN IMPROVED INVENTORY CONTROL ...AN IMPROVED INVENTORY CONTROL MODEL FOR THE BRAZILIAN NAVY SUPPLY SYSTEM Contract Number Grant Number Program Element Number Author(s) Moreira

On the relation between cost and service models for general inventory systems

NARCIS (Netherlands)

Houtum, van G.J.J.A.N.; Zijm, W.H.M.

2000-01-01

In this paper, we present a systematic overview of possible relations between cost and service models for fairly general single- and multi-stage inventory systems. In particular, we relate various types of penalty costs in pure cost models to equivalent types of service measures in service models.

The Relational Humor Inventory: Functions of Humor in Close Relationships.

Science.gov (United States)

DeKoning, E.; Weiss, R. L.

2002-01-01

This study describes the development of a self-report measure of functional humor in relationships. People were asked to report on their own and their partner's use of humor in the marriage. The Relational Humor Inventory proved to be a useful instrument for tapping important positive and negative relationship behaviors. (Contains 30 references, 4…

Tritium inventory measurements using calorimetry

International Nuclear Information System (INIS)

Kapulla, H.; Kraemer, R.; Heine, R.

1992-01-01

In the past calorimetry has been developed as a powerful tool in radiometrology. Calorimetric methods have been applied for the determination of activities, half lives and mean energies released during the disintegration of radioactive isotopes. The fundamental factors and relations which determine the power output of radioactive samples are presented and some basic calorimeter principles are discussed in this paper. At the Kernforschungszentrum Karlsruhe (KfK) a family of 3 calorimeters has been developed to measure the energy release from radiative waste products arising from reprocessing operations. With these calorimeters, radiative samples with sizes from a few cm 3 to 2 ·10 5 cm 3 and heat ratings ranging from a few nW to kW can be measured. After modifications of tits inner part the most sensitive calorimeter among the three calorimeters mentioned above would be best suited for measuring the tritium inventory in T-getters of the Amersham-type

Effects of control technology on the projected krypton-85 environmental inventory

International Nuclear Information System (INIS)

Oscarson, E.E.

1973-01-01

Growth projections for the USA nuclear power industry may be used to make projections of future radioactive material inventories available for potential release to the environment. Since krypton-85 is produced in reactors, the potential routes of release to the environment are at the reactors or the fuel reprocessing plants. The present generation of reactors and fuel reprocessing plants do not use any systems to limit the release of krypton-85 into the biosphere. Clean-up systems are currently being designed and could be introduced when necessary. The cumulative inventory of krypton-85 in the environment is dependent upon the time of introduction of these clean-up systems and their efficiencies, in addition to the total quantity produced. Annual and cumulative inventories of krypton-85 are projected to increase dramatically over the next 50 years. If controls are assumed to be initiated at various years, a series of graphs of different cumulative environmental inventories and the associated doses and health effects are drawn. Varying the year of introduction and the efficiency of these systems allows one to speculate as to the optimum time for control implementation

The Impact of Pollution Prevention on Toxic Environmental Releases from U.S. Manufacturing Facilities.

Science.gov (United States)

Ranson, Matthew; Cox, Brendan; Keenan, Cheryl; Teitelbaum, Daniel

2015-11-03

Between 1991 and 2012, the facilities that reported to the U.S. Environmental Protection Agency's Toxic Release Inventory (TRI) Program conducted 370,000 source reduction projects. We use this data set to conduct the first quasi-experimental retrospective evaluation of how implementing a source reduction (pollution prevention) project affects the quantity of toxic chemicals released to the environment by an average industrial facility. We use a differences-in-differences methodology, which measures how implementing a source reduction project affects a facility's releases of targeted chemicals, relative to releases of (a) other untargeted chemicals from the same facility, or (b) the same chemical from other facilities in the same industry. We find that the average source reduction project causes a 9-16% decrease in releases of targeted chemicals in the year of implementation. Source reduction techniques vary in effectiveness: for example, raw material modification causes a large decrease in releases, while inventory control has no detectable effect. Our analysis suggests that in aggregate, the source reduction projects carried out in the U.S. since 1991 have prevented between 5 and 14 billion pounds of toxic releases.

Fission Product Release Behavior of Individual Coated Fuel Particles for High-Temperature Gas-Cooled Reactors

International Nuclear Information System (INIS)

Minato, Kazuo; Sawa, Kazuhiro; Koya, Toshio; Tomita, Takeshi; Ishikawa, Akiyoshi; Baldwin, Charles A.; Gabbard, William Alexander; Malone, Charlie M.

2000-01-01

Postirradiation heating tests of TRISO-coated UO 2 particles at 1700 and 1800degC were performed to understand fission product release behavior at accident temperatures. The inventory measurements of the individual particles were carried out before and after the heating tests with gamma-ray spectrometry to study the behavior of the individual particles. The time-dependent release behavior of 85 Kr, 110m Ag, 134 Cs, 137 Cs, and 154 Eu were obtained with on-line measurements of fission gas release and intermittent measurements of metallic fission product release during the heating tests. The inventory measurements of the individual particles revealed that fission product release behavior of the individual particles was not uniform, and large particle-to-particle variations in the release behavior of 110m Ag, 134 Cs, 137 Cs, and 154 Eu were found. X-ray microradiography and ceramography showed that the variations could not be explained by only the presence or absence of cracks in the SiC coating layer. The SiC degradation may have been related to the variations

Assessment of Used Nuclear Fuel Inventory Relative to Disposition Options

International Nuclear Information System (INIS)

Wagner, John C.; Peterson, Joshua L.; Mueller, Don; Gehin, Jess C.; Worrall, Andrew; Taiwo, Temitope; Nutt, Mark; Williamson, Mark A.; Todosow, Mike; Wigeland, Roald; Halsey, William; Omberg, Ronald; Swift, Peter; Carter, Joe

2013-01-01

This paper presents a technical assessment of the current inventory [∼70,150 metric tons of heavy metal (MTHM) as of 2011] of U.S.-discharged used nuclear fuel (UNF) to support decisions regarding fuel cycle strategies and research, development and demonstration (RD and D) needs. The assessment considered discharged UNF from commercial nuclear electricity generation and defense and research programs and determined that the current UNF inventory can be divided into the following three categories: 1. Disposal - excess material that is not needed for other purposes; 2. Research - material needed for RD and D purposes to support waste management (e.g., UNF storage, transportation, and disposal) and development of alternative fuel cycles (e.g., separations and advanced fuels/reactors); and 3. Recycle/Recovery - material with inherent and/or strategic value. A set of key assumptions and attributes relative to the disposition options was used to categorize the current UNF inventory. Based on consideration of RD and D needs, time frames and material needs for deployment of alternative fuel cycles, characteristics of the current UNF inventory, and possible uses to support national security interests, it was determined that the vast majority of the category, without the need for retrieval for reuse or research purposes. Access to the material in the Research and Recycle/Recovery categories should be retained to support RD and D needs and national security interests. This assessment does not assume any decision about future fuel cycle options or preclude any potential options, including those with potential recycling of commercial UNF, since the ∼2,000 MTHM that is generated annually could provide the feedstock needed for deployment of alternative fuel cycles.

Inventory parameters

CERN Document Server

Sharma, Sanjay

2017-01-01

This book provides a detailed overview of various parameters/factors involved in inventory analysis. It especially focuses on the assessment and modeling of basic inventory parameters, namely demand, procurement cost, cycle time, ordering cost, inventory carrying cost, inventory stock, stock out level, and stock out cost. In the context of economic lot size, it provides equations related to the optimum values. It also discusses why the optimum lot size and optimum total relevant cost are considered to be key decision variables, and uses numerous examples to explain each of these inventory parameters separately. Lastly, it provides detailed information on parameter estimation for different sectors/products. Written in a simple and lucid style, it offers a valuable resource for a broad readership, especially Master of Business Administration (MBA) students.

Cost of umbilical cord blood units released for transplantation.

Science.gov (United States)

Sirchia, G; Rebulla, P; Tibaldi, S; Lecchi, L

1999-06-01

A large number of institutions have started programs banking umbilical cord blood (UCB) for allogeneic unrelated-donor and related-donor transplantation. However, limited information is available on the financial issues surrounding these activities. The aim of this study was to determine the fee per UCB unit released for transplantation that would allow cost recovery after 10 years. Three organizational models were considered suitable to provide units for five UCB transplants per 1 million population per year, a figure that would translate into an annual need for 280 units in Italy. Models A, B, and C included, respectively, seven networked banks, each with an inventory of 1,500 units; two networked banks, each with an inventory of 5,000 units; and one bank with an inventory of 10,000 units. It was estimated that it would take 3 years to develop the cryopreserved inventory and that approximately 3 percent of the inventory could be released and replaced each year during the 7-year interval between the fourth and tenth years of activity. The data on the costs of labor, reagents and diagnostics, disposables, depreciation and maintenance, laboratory tests, and overhead, as well as the operational data used in the analysis were collected at the Milano Cord Blood Bank in 1996. Fees of US $15,061, $12,666, and $11,602 per unit released during the fourth through the tenth years of activity allow full cost recovery (principle and interest) under Models A, B, and C, respectively. Although UCB procurement costs compare favorably with those of other hematopoietic cell sources, these results and the current fee of US $15,300 used in some institutions show that UCB is an expensive resource. Therefore, judicious planning of banking programs with high quality standards is necessary to prevent economic losses. The advantages of lower fees associated with the centralized banking approach of Model C should be balanced with the more flexible collection offered by Model A.

Tritium inventory prediction in a CANDU plant

International Nuclear Information System (INIS)

Song, M.J.; Son, S.H.; Jang, C.H.

1995-01-01

The flow of tritium in a CANDU nuclear power plant was modeled to predict tritium activity build-up. Predictions were generally in good agreement with field measurements for the period 1983--1994. Fractional contributions of coolant and moderator systems to the environmental tritium release were calculated by least square analysis using field data from the Wolsong plant. From the analysis, it was found that: (1) about 94% of tritiated heavy water loss came from the coolant system; (2) however, about 64% of environmental tritium release came from the moderator system. Predictions of environmental tritium release were also in good agreement with field data from a few other CANDU plants. The model was used to calculate future tritium build-up and environmental tritium release at Wolsong site, Korea, where one unit is operating and three more units are under construction. The model predicts the tritium inventory at Wolsong site to increase steadily until it reaches the maximum of 66.3 MCi in the year 2026. The model also predicts the tritium release rate to reach a maximum of 79 KCi/yr in the year 2012. To reduce the tritium inventory at Wolsong site, construction of a tritium removal facility (TRF) is under consideration. The maximum needed TRF capacity of 8.7 MCi/yr was calculated to maintain tritium concentration effectively in CANDU reactors

Fission product release from high gap-inventory LWR fuel under LOCA conditions

International Nuclear Information System (INIS)

Lorenz, R.A.; Collins, J.L.; Osborne, M.F.; Malinauskas, A.P.

1980-01-01

Fission product release tests were performed with light water reactor (LWR) fuel rod segments containing large amounts of cesium and iodine in the pellet-to-cladding gap space in order to check the validity of the previously published Source Term Model for this type of fuel. The model describes the release of fission product cesium and iodine from LWR fuel rods for controlled loss-of-coolant accident (LOCA) transients in the temperature range 500 to 1200 0 C. The basis for the model was test data obtained with simulated fuel rods and commercial fuel irradiated to high burnup but containing relatively small amounts of cesium and iodine in the pellet-to-cladding gap space

A description of the reactor inventory module NECTAR-RICE

International Nuclear Information System (INIS)

Nair, S.

1984-06-01

This note describes the NECTAR-RICE module of the CEGB's NECTAR environmental code, which can be used to calculate the actinide and/or fission product inventories of irradiated nuclear fuel used as input to the calculation of the release source term to atmosphere for accidental releases. The range of actinide and fission product nuclides considered is large enough to permit studies to be made for virtually any irradiation history consisting of ad hoc combinations of irradiation and cooling periods. The actinide and fission product inventories are calculated for burnup periods using numerical methods best suited to this problem, while analytical solutions are used for cooling periods. The code can be used to perform a coupled actinide-fission product calculation, a solely actinide calculation or a solely fission product calculation. Output consists of inventories, activities, and γ spectra, among others. A brief description is also given of previous work in this field. (author)

77 FR 1689 - Public Availability of Federal Labor Relations Authority FY 2011 Service Contract Inventory

Science.gov (United States)

2012-01-11

... FEDERAL LABOR RELATIONS AUTHORITY Public Availability of Federal Labor Relations Authority FY 2011 Service Contract Inventory AGENCY: Federal Labor Relations Authority. ACTION: Notice of Public... the Consolidated Appropriations Act of 2010 (Pub. L. 111-117), the Federal Labor Relations Authority...

76 FR 26296 - Public Availability of Federal Labor Relations Authority FY 2010 Service Contract Inventory

Science.gov (United States)

2011-05-06

... FEDERAL LABOR RELATIONS AUTHORITY Public Availability of Federal Labor Relations Authority FY 2010 Service Contract Inventory AGENCY: Federal Labor Relations Authority. ACTION: Notice of Public... the Consolidated Appropriations Act of 2010 (Pub. L. 111-117), the Federal Labor Relations Authority...

Inventory of chemical releases of nuclear installations in the North-Cotentin

International Nuclear Information System (INIS)

2002-05-01

The nuclear installations concerned by this study are Cogema La Hague, the Flamanville nuclear power plant, the Manche plant and the National Navy of Cherbourg.The objective followed by the ' source term ' work group has consisted in counting and examining the whole of existing measures relative to the releases of chemical substances in the liquid and gaseous effluents. Then because of the lack of measures for the operation first years of installations, the work group has estimated the order of magnitude of these chemical releases (essentially for Cogema La Hague). This report presents a review of the literature looking at the background levels of chemicals in different environmental compartments: air, soil, plants and animals products. these values have been summarized here to be available for comparisons with concentrations input by the North Cotentin nuclear installations, calculated by the G.R.N.C. (radioecology group of Nord Cotentin)

76 FR 40937 - Public Availability of National Labor Relations Board's FY 2010 Service Contract Inventory

Science.gov (United States)

2011-07-12

... NATIONAL LABOR RELATIONS BOARD Public Availability of National Labor Relations Board's FY 2010 Service Contract Inventory AGENCY: National Labor Relations Board. ACTION: Notice of public availability... Consolidated Appropriations Act of 2010 (Pub. L. 111-117), the National Labor Relations Board (NLRB) is...

77 FR 5062 - Public Availability of National Labor Relations Board's FY 2011 Service Contract Inventory

Science.gov (United States)

2012-02-01

... NATIONAL LABOR RELATIONS BOARD Public Availability of National Labor Relations Board's FY 2011 Service Contract Inventory AGENCY: National Labor Relations Board. ACTION: Notice of public availability... Consolidated Appropriations Act of 2010 (Pub. L. 111-117), the National Labor Relations Board (NLRB) is...

Inventory of Federal energy-related environment and safety research for FY 1978. Volume 1. Executive summary

International Nuclear Information System (INIS)

1979-12-01

The FY 1978 Federal Inventory is a compilation of 3225 federally funded energy-related environmental and safety reserch projects. It consists of three volumes: an executive summary providing an overview of the data (Volume I), a catalog listing each Inventory project followed by series of indexes (Volume II), and an interactive terminal guide giving instructions for on-line data retrieval (Volume III). Volume I reviews the inventory data as a whole and also within each of three major categories: biomedical and environmental research, environmental control technology research, and operational safety research

Fission Product Release Behavior of Individual Coated Fuel Particles for High-Temperature Gas-Cooled Reactors

Energy Technology Data Exchange (ETDEWEB)

Minato, Kazuo [Japan Atomic Energy Research Institute (Japan); Sawa, Kazuhiro [Japan Atomic Energy Research Institute (Japan); Koya, Toshio [Japan Atomic Energy Research Institute (Japan); Tomita, Takeshi [Japan Atomic Energy Research Institute (Japan); Ishikawa, Akiyoshi [Japan Atomic Energy Research Institute (Japan); Baldwin, Charles A; Gabbard, William Alexander [Oak Ridge National Laboratory (United States); Malone, Charlie M [Oak Ridge National Laboratory (United States)

2000-07-15

Postirradiation heating tests of TRISO-coated UO{sub 2} particles at 1700 and 1800degC were performed to understand fission product release behavior at accident temperatures. The inventory measurements of the individual particles were carried out before and after the heating tests with gamma-ray spectrometry to study the behavior of the individual particles. The time-dependent release behavior of {sup 85}Kr, {sup 110m}Ag, {sup 134}Cs, {sup 137}Cs, and {sup 154}Eu were obtained with on-line measurements of fission gas release and intermittent measurements of metallic fission product release during the heating tests. The inventory measurements of the individual particles revealed that fission product release behavior of the individual particles was not uniform, and large particle-to-particle variations in the release behavior of {sup 110m}Ag, {sup 134}Cs, {sup 137}Cs, and {sup 154}Eu were found. X-ray microradiography and ceramography showed that the variations could not be explained by only the presence or absence of cracks in the SiC coating layer. The SiC degradation may have been related to the variations.

Measurement of the gap and grain boundary inventories of Cs, Sr and I in domestic used PWR fuels

International Nuclear Information System (INIS)

Kim, S. S.; Choi, J. W.; Seo, H. S.; Cho, W. J.; Kang, K. C.; Kwon, S. H.

2007-01-01

Inventories of soluble elements in the gap and grain boundaries of domestic used PWR fuel pellets were measured to estimate the quantities of radionuclides that are liable to be rapidly released into the groundwater of a disposal site. The gap inventory of cesium for the pellets in the used fuel with a burn-up range of 45 to 66 GWD/MTU showed 0.85 to 1.7% of its total inventory, which was close to 1/6 to 1/3 of the fission gas release fraction (FGRF). However, the amounts of cesium released from the gaps of the pellets below 40 GWD/MTU of a burn-up and less than 1% FGRF were so erratic that the gap inventory could not be defined by its FGRF. Strontium inventories in the gap and grain boundaries of the pellets in the same rod were not significantly varied, and the iodine inventory in the gap of the used PWR fuels was estimated to be less than or the same as the FGRF

Implications of emission inventory choice for modeling fire-related pollution in the U.S.

Science.gov (United States)

Koplitz, S. N.; Nolte, C. G.; Pouliot, G.

2017-12-01

Wildland fires are a major source of fine particulate matter (PM2.5), one of the most harmful ambient pollutants for human health globally. Within the U.S., wildland fires can account for more than 30% of total annual PM2.5 emissions. In order to represent the influence of fire emissions on atmospheric composition, regional and global chemical transport models (CTMs) rely on fire emission inventories developed from estimates of burned area (i.e. fire size and location). Burned area can be estimated using a range of top-down and bottom-up approaches, including satellite-derived remote sensing and on-the-ground incident reports. While burned area estimates agree with each other reasonably well in the western U.S. (within 20-30% for most years during 2002-2014), estimates for the southern U.S. vary by more than a factor of 3. Differences in burned area estimation methods lead to significant variability in the spatial and temporal allocation of emissions across fire emission inventory platforms. In this work, we implement fire emission estimates for 2011 from three different products - the USEPA National Emission Inventory (NEI), the Fire INventory of NCAR (FINN), and the Global Fire Emission Database (GFED4s) - into the Community Multiscale Air Quality (CMAQ) model to quantify and characterize differences in simulated fire-related PM2.5 and ozone concentrations across the contiguous U.S. due solely to the emission inventory used. Preliminary results indicate that the estimated contribution to national annual average PM2.5 from wildland fire in 2011 is highest using GFED4s emissions (1.0 µg m-3) followed by NEI (0.7 µg m-3) and FINN (0.3 µg m-3), with comparisons varying significantly by region and season. Understanding the sensitivity of modeling fire-related PM2.5 and ozone in the U.S. to fire emission inventory choice will inform future efforts to assess the implications of present and future fire activity for air quality and human health at national and global

Quantitative Analysis of Kr-85 Fission Gas Release from Dry Process for the Treatment of Spent PWR Fuel

International Nuclear Information System (INIS)

Park, Geun Il; Cho, Kwang Hun; Lee, Dou Youn; Lee, Jung Won; Park, Jang Jin; Song, Kee Chan

2007-01-01

As spent UO 2 fuel oxidizes to U 3 O 8 by air oxidation, a corresponding volume expansion separate grains, releasing the grain-boundary inventory of fission gases. Fission products in spent UO 2 fuel can be distributed in three major regions : the inventory in fuel-sheath gap, the inventory on grain boundaries and the inventory in UO 2 matrix. Release characteristic of fission gases depends on its distribution amount in three regions as well as spent fuel burn-up. Oxidation experiments of spent fuel at 500 .deg. C gives the information of fission gases inventory in spent fuel, and further annealing experiments at higher temperature produces matrix inventory of fission gases on segregated grain. In previous study, fractional release characteristics of Kr- 85 during OREOX (Oxidation and REduction of Oxide fuel) treatment as principal key process for recycling spent PWR fuel via DUPIC cycle have already evaluated as a function of fuel burn-up with 27.3, 35 and 65 MWd/tU. In this paper, new release experiment results of Kr-85 using spent fuel with burn- up of 58 GWd/tU are included to evaluate the fission gas release behavior. As a point of summary in fission gases release behavior, the quantitative analysis of Kr- 85 release characteristics from various spent fuels with different burn-up during voloxidation and OREOX process were reviewed

Inventory of Engineered Nanoparticle-Containing Consumer Products Available in the Singapore Retail Market and Likelihood of Release into the Aquatic Environment.

Science.gov (United States)

Zhang, Yuanyuan; Leu, Yu-Rui; Aitken, Robert J; Riediker, Michael

2015-07-24

Consumer products containing engineered nanoparticles (ENP) are already entering the marketplace. This leads, inter alia, to questions about the potential for release of ENP into the environment from commercial products. We have inventoried the prevalence of ENP-containing consumer products in the Singapore market by carrying out onsite assessments of products sold in all major chains of retail and cosmetic stores. We have assessed their usage patterns and estimated release factors and emission quantities to obtain a better understanding of the quantities of ENP that are released into which compartments of the aquatic environment in Singapore. Products investigated were assessed for their likelihood to contain ENP based on the declaration of ENP by producers, feature descriptions, and the information on particle size from the literature. Among the 1,432 products investigated, 138 were "confirmed" and 293 were "likely" to contain ENP. Product categories included sunscreens, cosmetics, health and fitness, automotive, food, home and garden, clothing and footwear, and eyeglass/lens coatings. Among the 27 different types of nanomaterials identified, SiO2 was predominant, followed by TiO2 and ZnO, Carbon Black, Ag, and Au. The amounts of ENP released into the aquatic system, which was estimated on the basis of typical product use, ENP concentration in the product, daily use quantity, release factor, and market share, were in the range of several hundred tons per year. As these quantities are likely to increase, it will be important to further study the fate of ENP that reach the aquatic environment in Singapore.

Inventory of Engineered Nanoparticle-Containing Consumer Products Available in the Singapore Retail Market and Likelihood of Release into the Aquatic Environment

Directory of Open Access Journals (Sweden)

Yuanyuan Zhang

2015-07-01

Full Text Available Consumer products containing engineered nanoparticles (ENP are already entering the marketplace. This leads, inter alia, to questions about the potential for release of ENP into the environment from commercial products. We have inventoried the prevalence of ENP-containing consumer products in the Singapore market by carrying out onsite assessments of products sold in all major chains of retail and cosmetic stores. We have assessed their usage patterns and estimated release factors and emission quantities to obtain a better understanding of the quantities of ENP that are released into which compartments of the aquatic environment in Singapore. Products investigated were assessed for their likelihood to contain ENP based on the declaration of ENP by producers, feature descriptions, and the information on particle size from the literature. Among the 1,432 products investigated, 138 were “confirmed” and 293 were “likely” to contain ENP. Product categories included sunscreens, cosmetics, health and fitness, automotive, food, home and garden, clothing and footwear, and eyeglass/lens coatings. Among the 27 different types of nanomaterials identified, SiO2 was predominant, followed by TiO2 and ZnO, Carbon Black, Ag, and Au. The amounts of ENP released into the aquatic system, which was estimated on the basis of typical product use, ENP concentration in the product, daily use quantity, release factor, and market share, were in the range of several hundred tons per year. As these quantities are likely to increase, it will be important to further study the fate of ENP that reach the aquatic environment in Singapore.

Consequences of severe radioactive releases to Nordic Marine environment

DEFF Research Database (Denmark)

Iosjpe, M.; Isaksson, M.; Joensen, H.P.

- or minor – radioactive releases to Nordic marine environment. As a reference, the release amounts from a 3000 MWth reactor size were used. Based on source term analyses, the chosen release fractions in the study were: iodine 20% (of the total core inventory), caesium 10%, tellurium 10%, strontium 0...

Development of a symptoms questionnaire for complex regional pain syndrome and potentially related illnesses: the Trauma Related Neuronal Dysfunction Symptoms Inventory

NARCIS (Netherlands)

Collins, S.; van Hilten, J.J.; Marinus, J.J.; Zuurmond, W.W.A.; de Lange, J.J.; Perez, R.S.G.M.

2008-01-01

Collins S, van Hilten JJ, Marinus J, Zuurmond WW, de Lange JJ, Perez RS. Development of a symptoms questionnaire for complex regional pain syndrome and potentially related illnesses: the Trauma Related Neuronal Dysfunction Symptoms Inventory. Objective: To develop a questionnaire to evaluate

COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

Energy Technology Data Exchange (ETDEWEB)

S.O. Bader

1999-10-18

The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

COMMERCIAL SNF ACCIDENT RELEASE FRACTIONS

International Nuclear Information System (INIS)

S.O. Bader

1999-01-01

The purpose of this design analysis is to specify and document the total and respirable fractions for radioactive materials that are released from an accident event at the Monitored Geologic Repository (MGR) involving commercial spent nuclear fuel (CSNF) in a dry environment. The total and respirable release fractions will be used to support the preclosure licensing basis for the MGR. The total release fraction is defined as the fraction of total CSNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. The radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses. This subset of the total release fraction is referred to as the respirable release fraction. Potential accidents may involve waste forms that are characterized as either bare (unconfined) fuel assemblies or confined fuel assemblies. The confined CSNF assemblies at the MGR are contained in shipping casks, canisters, or disposal containers (waste packages). In contrast to the bare fuel assemblies, the container that confines the fuel assemblies has the potential of providing an additional barrier for diminishing the total release fraction should the fuel rod cladding breach during an accident. However, this analysis will not take credit for this additional bamer and will establish only the total release fractions for bare unconfined CSNF assemblies, which may however be

2002 Toxic Chemical Release Inventory Report for the Emergency Planning and Community Right-to-Know Act of 1986, Title III, Section 313

International Nuclear Information System (INIS)

Stockton, M.

2003-01-01

For reporting year 2002, Los Alamos National Laboratory (LANL or the Laboratory) submitted Form R reports for lead compounds and mercury as required under the Emergency Planning and Community Right-to-Know Act (EPCRA), Section 313. No other EPCRA Section 313 chemicals were used in 2002 above the reportable thresholds. This document was prepared to provide a description of the evaluation of EPCRA Section 313 chemical usage and threshold determinations for LANL for calendar year 2002 as well as provide background information about the data included on the Form R reports. Section 313 of EPCRA specifically requires facilities to submit a Toxic Chemical Release Inventory report (Form R) to the U.S. Environmental Protection Agency (EPA) and state agencies if the owners and operators manufacture, process, or otherwise use any of the listed toxic chemicals above listed threshold quantities. EPA compiles this data in the Toxic Release Inventory database. Form R reports for each chemical over threshold quantities must be submitted on or before July 1 each year and must cover activities that occurred at the facility during the previous year. In 1999 EPA promulgated a final rule on Persistent Bioaccumulative Toxics (PBTs). This rule added several chemicals to the EPCRA Section 313 list of toxic chemicals and established lower reporting thresholds for these and other PBT chemicals that were already reportable under EPCRA Section 313. These lower thresholds became applicable in reporting year 2000. In 2001, EPA expanded the PBT rule to include a lower reporting threshold for lead and lead compounds. Facilities that manufacture, process, or otherwise use more than 100 lb of lead or lead compounds must submit a Form R

2006 Toxic Chemical Release Inventory Report for the Emergency Planning and Community Right-to-Know Act of 1986, Title III, Section 313

Energy Technology Data Exchange (ETDEWEB)

Ecology and Air Quality Group (ENV-EAQ)

2007-12-12

For reporting year 2006, Los Alamos National Laboratory (LANL or the Laboratory) submitted Form R reports for lead as required under the Emergency Planning and Community Right-to-Know Act (EPCRA) Section 313. No other EPCRA Section 313 chemicals were used in 2006 above the reportable thresholds. This document was prepared to provide a description of the evaluation of EPCRA Section 313 chemical use and threshold determinations for LANL for calendar year 2006, as well as to provide background information about data included on the Form R reports. Section 313 of EPCRA specifically requires facilities to submit a Toxic Chemical Release Inventory Report (Form R) to the U.S. Environmental Protection Agency (EPA) and state agencies if the owners and operators manufacture, process, or otherwise use any of the listed toxic chemicals above listed threshold quantities. EPA compiles this data in the Toxic Release Inventory database. Form R reports for each chemical over threshold quantities must be submitted on or before July 1 each year and must cover activities that occurred at the facility during the previous year. In 1999, EPA promulgated a final rule on persistent bioaccumulative toxics (PBTs). This rule added several chemicals to the EPCRA Section 313 list of toxic chemicals and established lower reporting thresholds for these and other PBT chemicals that were already reportable. These lower thresholds became applicable in reporting year 2000. In 2001, EPA expanded the PBT rule to include a lower reporting threshold for lead and lead compounds. Facilities that manufacture, process, or otherwise use more than 100 lb of lead or lead compounds must submit a Form R.

Global radioxenon emission inventory based on nuclear power reactor reports.

Science.gov (United States)

Kalinowski, Martin B; Tuma, Matthias P

2009-01-01

Atmospheric radioactivity is monitored for the verification of the Comprehensive Nuclear-Test-Ban Treaty, with xenon isotopes 131mXe, 133Xe, 133mXe and 135Xe serving as important indicators of nuclear explosions. The treaty-relevant interpretation of atmospheric concentrations of radioxenon is enhanced by quantifying radioxenon emissions released from civilian facilities. This paper presents the first global radioxenon emission inventory for nuclear power plants, based on North American and European emission reports for the years 1995-2005. Estimations were made for all power plant sites for which emission data were unavailable. According to this inventory, a total of 1.3PBq of radioxenon isotopes are released by nuclear power plants as continuous or pulsed emissions in a generic year.

Low and intermediate level waste in SFR-1. Reference waste inventory

International Nuclear Information System (INIS)

Riggare, P.; Johansson, Claes

2001-06-01

The objective with this report is to describe all the waste and the waste package that is expected to be deposited in SFR-1 at the time of closure. This report is a part of the SAFE project (Safety Assessment of Final Repository for Radioactive Operational Waste), i.e. the renewed safety assessment of SFR-1. The accounted waste inventory has been used as input to the release calculation that has been performed in the SAFE project. The waste inventory is based on an estimated operational lifetime of the Swedish nuclear power plants of 40 years and that closure of the SFR repository will happen in 2030. In the report, data about geometries, weights, materials, chemicals and radionuclide are given. No chemo toxic material has been identified in the waste. The inventory is based on so called waste types and the waste types reference waste package. The reference waste package combined with a prognosis of the number of waste packages to the year 2030 gives the final waste inventory for SFR-1. All reference waste packages are thoroughly described in the appendices of this report. The reference waste packages are as far as possible based on actual experiences and measurements. The radionuclide inventory is also based on actual measurements. The inventory is based on measurements of 60 Co and 137 Cs in waste packages and on measurements 239 Pu and 240 Pu in reactor water. Other nuclides in the inventory are calculated with correlation factors. In the SAFE project's prerequisites it was said that one realistic and one conservative (pessimistic) inventory should be produced. The conservative one should then be used for the release calculations. In this report one realistic and one conservative radionuclide inventory is presented. The conservative one adds up to 10 16 Bq. Regarding materials there is only one inventory given since it is not certain what is a conservative assumption

Fusion program research materials inventory

International Nuclear Information System (INIS)

Roche, T.K.; Wiffen, F.W.; Davis, J.W.; Lechtenberg, T.A.

1984-01-01

Oak Ridge National Laboratory maintains a central inventory of research materials to provide a common supply of materials for the Fusion Reactor Materials Program. This will minimize unintended material variations and provide for economy in procurement and for centralized record keeping. Initially this inventory is to focus on materials related to first-wall and structural applications and related research, but various special purpose materials may be added in the future. The use of materials from this inventory for research that is coordinated with or otherwise related technically to the Fusion Reactor Materials Program of DOE is encouraged

A recommended approach to the National Pollutant Release Inventory (NPRI) for the upstream oil and gas industry : 2002 : CAC emissions

International Nuclear Information System (INIS)

2003-04-01

The National Pollutant Release Inventory (NPRI) is a database of annual releases to air, water, land and off-site transfers of 273 specified pollutants. Environment Canada requires that the NPRI be reported annually. Criteria Air Contaminants (CAC) had to be reported for the first time in 2002. Air pollutants that contribute to the formation of ground level ozone and smog are included in the definition of CAC, along with any eye or respiratory irritants to both humans and animals. The substances of special interest to the petroleum industry are: oxides of nitrogen, sulphur dioxide, carbon monoxide, volatile organic compounds, total particulate matter, and particulate matters. This guide is intended to provide member companies of Canadian Association of Petroleum Producers (CAPP), operating upstream oil and gas facilities, with readily available data to determine the amount of CAC emissions released from their processes and equipment. Companies using these guidelines will be able to compare the performance of various upstream oil and gas companies more readily because the data is consistent. The scope of the project was described in section 1, and the sources of CAC emissions were identified in section 2. The reporting threshold was discussed in section 3. Data required for collection was outlined in section 4. Section 5 outlines how CAC emission quantities are determined. Calculation examples were provided in section 6 and definitions provided in section 7. 11 tabs., 1 fig

Gas generation in SFL 3-5 and effects on radionuclide release

International Nuclear Information System (INIS)

Skagius, K.; Lindgren, M.; Pers, K.

1999-12-01

A deep repository, SFL 3-5, is presently planned for disposing of long-lived low- and intermediate-level waste. In this study the amounts of gas that can be generated in the waste packages and in the vaults are estimated. The potential gas pressure build-up, the displacement of contaminated water and the consequences on radionuclide release from the engineered barriers in the repository are also addressed. The study is focussed on the repository design and waste inventory that was defined for the prestudy of SFL 3-5. Since the reporting of the prestudy the design of the repository has been modified and the waste inventory has been updated and a preliminary safety assessment of the repository has been carried out based on the new design and updated waste inventory. The implications on gas generation and release of these modifications in design and waste inventory are briefly addressed in this study

Gas generation in SFL 3-5 and effects on radionuclide release

Energy Technology Data Exchange (ETDEWEB)

Skagius, K.; Lindgren, M.; Pers, K. [Kemakta Konsult AB, Stockholm (Sweden)

1999-12-01

A deep repository, SFL 3-5, is presently planned for disposing of long-lived low- and intermediate-level waste. In this study the amounts of gas that can be generated in the waste packages and in the vaults are estimated. The potential gas pressure build-up, the displacement of contaminated water and the consequences on radionuclide release from the engineered barriers in the repository are also addressed. The study is focussed on the repository design and waste inventory that was defined for the prestudy of SFL 3-5. Since the reporting of the prestudy the design of the repository has been modified and the waste inventory has been updated and a preliminary safety assessment of the repository has been carried outbased on the new design and updated waste inventory. The implications on gas generation and release of these modifications in design and waste inventory are briefly addressed in this study.

A consumption-based GHG inventory for the U.S. state of Oregon.

Science.gov (United States)

Erickson, Peter; Allaway, David; Lazarus, Michael; Stanton, Elizabeth A

2012-04-03

Many U.S. states conduct greenhouse gas (GHG) inventories to inform their climate change planning efforts. These inventories usually follow a production-based method adapted from the Intergovernmental Panel on Climate Change. States could also take a consumption-based perspective, however, and estimate all emissions released to support consumption in their state, regardless of where the emissions occur. In what may be the first such comprehensive inventory conducted for a U.S. state, we find that consumption-based emissions for Oregon are 47% higher than those released in-state. This finding implies that Oregon's contribution to global greenhouse gas emissions (carbon footprint) is considerably higher than traditional production-based methods would suggest. Furthermore, the consumption-based inventory helps highlight the role of goods and services (and associated purchasing behaviors) more so than do production-based methods. Accordingly, a consumption-based perspective opens new opportunities for many states and their local government partners to reduce GHG emissions, such as initiatives to advance lower-carbon public sector or household consumption, that are well within their sphere of influence. State and local governments should consider conducting consumption-based GHG inventories and adopting consumption-based emission reductions targets in order to broaden the reach and effectiveness of state and local actions in reducing global GHG emissions. Consumption-based frameworks should be viewed as a complement to, but not a substitute for, production-based (in-state) GHG emissions inventories and targets.

Toxic releases from power plants

International Nuclear Information System (INIS)

Rubin, E.S.

1999-01-01

Beginning in 1998, electric power plants burning coal or oil must estimate and report their annual releases of toxic chemicals listed in the Toxics Release Inventory (TRI) published by the US Environmental Protection Agency (EPA). This paper identifies the toxic chemicals of greatest significance for the electric utility sector and develops quantitative estimates of the toxic releases reportable to the TRI for a representative coal-fired power plant. Key factors affecting the magnitude and types of toxic releases for individual power plants also are discussed. A national projection suggests that the magnitude of electric utility industry releases will surpass those of the manufacturing industries which current report to the TRI. Risk communication activities at the community level will be essential to interpret and provide context for the new TRI results

Associations between Single-Nucleotide Polymorphisms in Corticotropin-Releasing Hormone-Related Genes and Irritable Bowel Syndrome.

Directory of Open Access Journals (Sweden)

Ayaka Sasaki

Full Text Available Irritable bowel syndrome (IBS is a common functional disorder with distinct features of stress-related pathophysiology. A key mediator of the stress response is corticotropin-releasing hormone (CRH. Although some candidate genes have been identified in stress-related disorders, few studies have examined CRH-related gene polymorphisms. Therefore, we tested our hypothesis that single-nucleotide polymorphisms (SNPs in CRH-related genes influence the features of IBS.In total, 253 individuals (123 men and 130 women participated in this study. They comprised 111 IBS individuals and 142 healthy controls. The SNP genotypes in CRH (rs28364015 and rs6472258 and CRH-binding protein (CRH-BP (rs10474485 were determined by direct sequencing and real-time polymerase chain reaction. The emotional states of the subjects were evaluated using the State-Trait Anxiety Inventory, Perceived Stress Scale, and the Self-rating Depression Scale.Direct sequencing of the rs28364015 SNP of CRH revealed no genetic variation among the study subjects. There was no difference in the genotype distributions and allele frequencies of rs6472258 and rs10474485 between IBS individuals and controls. However, IBS subjects with diarrhea symptoms without the rs10474485 A allele showed a significantly higher emotional state score than carriers.These results suggest that the CRH and CRH-BP genes have no direct effect on IBS status. However, the CRH-BP SNP rs10474485 has some effect on IBS-related emotional abnormalities and resistance to psychosocial stress.

Release of segregated nuclides from spent fuel

Energy Technology Data Exchange (ETDEWEB)

Johnson, L.H.; Tait, J.C. [Atomic Energy Canada Ltd., Pinawa, MB (Canada). Whiteshell Laboratories

1997-10-01

The potential release of fission and activation products from spent nuclear fuel into groundwater after container failure in the Swedish deep repository is discussed. Data from studies of fission gas release from representative Swedish BWR fuel are used to estimate the average fission gas release for the spent fuel population. Information from a variety of leaching studies on LWR and CANDU fuel are then reviewed as a basis for estimating the fraction of the inventory of key radionuclides that could be released preferentially (the Instant Release Fraction of IRF) upon failure of the fuel cladding. The uncertainties associated with these estimates are discussed. 33 refs, 6 figs, 3 tabs.

Nuclear material inventory estimation in solvent extraction contactors

International Nuclear Information System (INIS)

Beyerlein, A.; Geldard, J.

1986-06-01

This report describes the development of simple nuclear material (uranium and plutonium) inventory relations for mixer-settler solvent extraction contactors used in reprocessing spent nuclear fuels. The relations are developed for light water reactor fuels where the organic phase is 30% tri-n-butylphosphate (TBP) by volume. For reprocessing plants using mixer-settler contactors as much as 50% of the nuclear material within the contactors is contained in A type (aqueous to organic extraction) contactors. Another very significant portion of the contactor inventory is in the partitioning contactors. The stripping contactors contain a substantial uranium inventory but contain a very small plutonium inventory (about 5 to 10% of the total contactor inventory). The simplified inventory relations developed in this work for mixer-settler contactors reproduce the PUBG databases within about a 5% standard deviation. They can be formulated to explicitly show the dependence of the inventory on nuclear material concentrations in the aqueous feed streams. The dependence of the inventory on contactor volumes, phase volume ratios, and acid and TBP concentrations are implicitly contained in parameters that can be calculated for a particular reprocessing plant from nominal flow sheet data. The terms in the inventory relations that represent the larger portion of the inventory in A type and partitioning contactors can be extended to pulsed columns virtually without change

Commercial SNF Accident Release Fractions

Energy Technology Data Exchange (ETDEWEB)

J. Schulz

2004-11-05

The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M&O 1999). In contrast to bare unconfined fuel assemblies, the

Commercial SNF Accident Release Fractions

International Nuclear Information System (INIS)

Schulz, J.

2004-01-01

The purpose of this analysis is to specify and document the total and respirable fractions for radioactive materials that could be potentially released from an accident at the repository involving commercial spent nuclear fuel (SNF) in a dry environment. The total and respirable release fractions are used to support the preclosure licensing basis for the repository. The total release fraction is defined as the fraction of total commercial SNF assembly inventory, typically expressed as an activity inventory (e.g., curies), of a given radionuclide that is released to the environment from a waste form. Radionuclides are released from the inside of breached fuel rods (or pins) and from the detachment of radioactive material (crud) from the outside surfaces of fuel rods and other components of fuel assemblies. The total release fraction accounts for several mechanisms that tend to retain, retard, or diminish the amount of radionuclides that are available for transport to dose receptors or otherwise can be shown to reduce exposure of receptors to radiological releases. The total release fraction includes a fraction of airborne material that is respirable and could result in inhalation doses; this subset of the total release fraction is referred to as the respirable release fraction. Accidents may involve waste forms characterized as: (1) bare unconfined intact fuel assemblies, (2) confined intact fuel assemblies, or (3) canistered failed commercial SNF. Confined intact commercial SNF assemblies at the repository are contained in shipping casks, canisters, or waste packages. Four categories of failed commercial SNF are identified: (1) mechanically and cladding-penetration damaged commercial SNF, (2) consolidated/reconstituted assemblies, (3) fuel rods, pieces, and debris, and (4) nonfuel components. It is assumed that failed commercial SNF is placed into waste packages with a mesh screen at each end (CRWMS M andO 1999). In contrast to bare unconfined fuel assemblies, the

An Emission Inventory of Polycyclic Aromatic Hydrocarbons in China

Science.gov (United States)

Mu, Xilong; Zhu, Xianlei; Wang, Xuesong

2015-04-01

Polycyclic Aromatic Hydrocarbons (PAHs) are among the most dangerous compounds due to their high carcinogenic and mutagenic character. Emission inventory provides the primary data to account for the sources of ambient PAHs and server as a necessary database for effective PAHs pollution control. China is experiencing fast economic growth and large energy consumption, which might result in a large amount of PAHs anthropogenic emissions. Therefore, based on the previous studies and combined recently field emission measurements as well as socio-economic activity data, the development of a nationwide PAHs emission inventory is needed. In this work, the emission inventory of 16 PAHs listed as U.S. Environmental Protection Agency priority pollutants in China in the year 2012 is compiled. The emission amounts of PAHs were estimated as annual rates of emission-related activities multiplied by respective emission factors. The activities such as fuel consumption, including fossil fuel and biofuel, and socio-economic statistics were obtained from yearbook released by Chinese central government and/or provincial governments, as well as related industry reports. Emission factors were derived from the related literature. Recently reported emission factors from local measurements were used. The total emissions of PAHs were 120611 ton in 2012. In China, PAHs were emitted predominantly from domestic combustion of coal and biofuel, coking industry and motor vehicles, accounting for 72% of the total amount. PAHs emission profiles were significantly different between China and the other countries. The emission profile in China featured a relatively higher portion of high molecular weight species with carcinogenic potential due to large contributions of domestic combustion and coking industry. Domestic combustion of straw, coal and firewood emitted 19464 ton, 8831 ton, and 5062 ton of PAHs, respectively, which were much higher than those in other countries. Emission per capita showed

Inventory of accidents and losses at sea involving radioactive material

International Nuclear Information System (INIS)

2001-09-01

The present report describes the content of the inventory of accidents and losses at sea involving radioactive material. It covers accidents and losses resulting in the actual release of radioactive materials into the marine environment and also those which have the potential for release. For completeness, records of radioactive materials involved in accidents but which were recovered intact from the sea are also reported. Information on losses of sealed sources resulting in actual or potential release of activity to the marine environment nad of sealed sources that were recovered intact is also presented

The estimation and prediction of the inventories for the liquid and gaseous radwaste systems using the linear regression analysis

International Nuclear Information System (INIS)

Kim, J. Y.; Shin, C. H.; Kim, J. K.; Lee, J. K.; Park, Y. J.

2003-01-01

The variation transitions of the inventories for the liquid radwaste system and the radioactive gas have being released in containment, and their predictive values according to the operation histories of Yonggwang(YGN) 3 and 4 were analyzed by linear regression analysis methodology. The results show that the variation transitions of the inventories for those systems are linearly increasing according to the operation histories but the inventories released to the environment are considerably lower than the recommended values based on the FSAR suggestions. It is considered that some conservation were presented in the estimation methodology in preparing stage of FSAR

Calculation of the inventory and near-field release rates of radioactivity from neutron-activated metal parts discharged from the high flux isotope reactor and emplaced in solid waste storage area 6 at Oak Ridge National Laboratory

Energy Technology Data Exchange (ETDEWEB)

Kelmers, A.D.; Hightower, J.R.

1987-05-01

Emplacement of contaminated reactor components involves disposal in lined and unlined auger holes in soil above the water table. The radionuclide inventory of disposed components was calculated. Information on the composition and weight of the components, as well as reasonable assumptions for the neutron flux fueling use, the time of neutron exposure, and radioactive decay after discharge, were employed in the inventory calculation. Near-field release rates of /sup 152/Eu, /sup 154/Eu, and /sup 155/Eu from control plates and cylinders were calculated for 50 years after emplacement. Release rates of the europium isotopes were uncertain. Two release-rate-limiting models were considered and a range of reasonable values were assumed for the time-to-failure of the auger-hole linear and aluminum cladding and europium solubility in SWSA-6 groundwater. The bounding europium radionuclide near-field release rates peaked at about 1.3 Ci/year total for /sup 152,154,155/Eu in 1987 for the lower bound, and at about 420 Ci/year in 1992 for the upper bound. The near-field release rates of /sup 55/Fe, /sup 59/Ni, /sup 60/Co, and /sup 63/Ni from stainless steel and cobalt alloy components, as well as of /sup 10/Be, /sup 41/Ca, and /sup 55/Fe from beryllium reflectors, were calculated for the next 100 years, assuming bulk waste corrosion was the release-rate-limiting step. Under the most conservative assumptions for the reflectors, the current (1986) total radionuclide release rate was calculated to be about 1.2 x 10/sup -4/ Ci/year, decreasing by 1992 to a steady release of about 1.5 x 10/sup -5/ Ci/year due primarily to /sup 41/Ca. 50 refs., 13 figs., 8 tabs.

Increased release of histamine in patients with respiratory symptoms related to perfume.

Science.gov (United States)

Elberling, J; Skov, P S; Mosbech, H; Holst, H; Dirksen, A; Johansen, J D

2007-11-01

Environmental perfume exposure may cause respiratory symptoms. Individuals with asthma and perfume contact allergy report such symptoms more frequently than others. However, immunologic mechanisms have not been demonstrated and the symptoms are not associated with IgE-mediated allergy. The study aimed to investigate whether basophils from patients with respiratory symptoms related to perfume released more histamine in the presence of perfume as compared with healthy volunteers. Histamine release was measured by the glass fibre method. Blood was obtained from healthy volunteers (n=20) and patients with respiratory symptoms related to perfume (n=17) attending a dermatological outpatient clinic for patch testing. The effect of an international brand perfume was investigated using the basophil histamine release test with perfume. Furthermore, basophils from a healthy non-atopic donor were incubated with participant's sera and histamine release induced by perfume was measured. In both groups incremental perfume concentrations showed a positive and significant (Pperfume concentration, the basophils released significantly (PPerfume induces a dose-dependent non-IgE-mediated release of histamine from human peripheral blood basophils. Increased basophil reactivity to perfume was found in patients with respiratory symptoms related to perfume.

INVENTORY MANAGEMENT IN THE ENTERPRISE THROUGH THE APPLICATION OF IFRS 2 INVENTORIES

Directory of Open Access Journals (Sweden)

Svetlozar Stefanov

2016-07-01

Full Text Available The focus in the article is on the issues of valuation and presentation of the inventories under the meaning on the International Accounting Standard 2 Inventories. The Standard provides guidance on the determination of costs of finished products and its recognition as and expense in the production and sale finished products, including guidance for determination of the net realizable value. The latter is defined as the estimated selling price less the estimated costs of completion and estimated costs necessary to make the sale. The cost of inventories comprises all costs of purchase, cost of conversion and other costs incurred in bringing the inventories to a condition suitable for subsequent use. The amount of the cost for materials used or products sold and the finished product is determined using one of the following methods: a specifically defined value, first-in � first out or weighted average cost of lots delivered. When inventories are sold, the carrying amount of those inventories is recognized as an expense in the period in which the related sales revenue is recognized. The amount of any write-down of inventories to net realizable value is recorded as a current expense and is recognized as an expense in the period the write-down occurs.

Tritium release from neutron irradiated beryllium pebbles

Energy Technology Data Exchange (ETDEWEB)

Scaffidi-Argentina, F.; Werle, H. [Forschungszentrum Karlsruhe GmbH Technik und Umwelt (Germany). Inst. fuer Neutronenphysik und Reactortechnik

1998-01-01

One of the most important open issues related to beryllium for fusion applications refers to the kinetics of the tritium release as a function of neutron fluence and temperature. The EXOTIC-7 as well as the `Beryllium` experiments carried out in the HFR reactor in Petten are considered as the most detailed and significant tests for investigating the beryllium response under neutron irradiation. This paper reviews the present status of beryllium post-irradiation examinations performed at the Forschungszentrum Karlsruhe with samples from the above mentioned irradiation experiments, trying to elucidate the tritium release controlling processes. In agreement with previous studies it has been found that release starts at about 500-550degC and achieves a maximum at about 700-750degC. The observed release at about 500-550degC is probably due to tritium escaping from chemical traps, while the maximum release at about 700-750degC is due to tritium escaping from physical traps. The consequences of a direct contact between beryllium and ceramics during irradiation, causing tritium implanting in a surface layer of beryllium up to a depth of about 40 mm and leading to an additional inventory which is usually several times larger than the neutron-produced one, are also presented and the effects on the tritium release are discussed. (author)

Global Inventory of Methane Hydrate: How Large is the Threat? (Invited)

Science.gov (United States)

Buffett, B. A.; Frederick, J. M.

2010-12-01

Methane hydrate is a dark horse in the science of climate change. The volume of methane sequestered in marine sediments is large enough to pose a potential threat, yet the expected contribution to future warming is not known. Part of the uncertainty lies in the poorly understood details of methane release from hydrate. Slow, diffusive loss of methane probably results in oxidation by sulfate and precipitation to CaCO3 in the sediments, with little effect on climate. Conversely, a direct release of methane into the atmosphere is liable to have strong and immediate consequences. Progress in narrowing the possibilities requires a better understanding of the mechanisms responsible for methane release. Improvements are also needed in our estimates of the hydrate inventory, as this sets a limit on the possible response. Several recent estimates of the hydrate inventory have been constructed using mechanistic models. Many of the model parameters (e.g. sedimentation rate and sea floor temperature) can be estimated globally, while others (e.g. vertical fluid flow) are not well known. Available observations can be used to estimate the poorly known parameters, but it is reasonable to question whether the results from a limited number of sites are representative of other locations. Fluid flow is a case in point because most hydrate locations are associated with upward flow. On the other hand, simple models of sediment compaction predict downward flow relative to the sea floor, which acts to impede hydrate formation. A variety of mechanisms can produce upward flow, including time-dependent sedimentation, seafloor topography, subsurface fractures, dehydration of clay minerals and gradual burial of methane hydrate below the stability zone. Each of these mechanisms makes specific predictions for the magnitude of flow and the proportion of sea floor that is likely to be affected. We assess the role of fluid flow on the present-day inventory and show that the current estimates for

Trends in State and Federal land use law relating to inventories, monitoring and evaluation

Science.gov (United States)

Lamb, C. M.

1974-01-01

A description and analysis of selected State and Federal laws relating to land use inventories, monitoring, and evaluation is presented. Legal requirements and information systems for land use in the following states are reviewed: Colorado, Delaware, Florida, Hawaii, Indiana, Kansas, Maine, Mississippi, Missouri, Oklahoma, Pennsylvania, Tennessee, Utah, Vermont, and West Virginia.

Update and improvement of the global krypton-85 emission inventory

International Nuclear Information System (INIS)

Ahlswede, Jochen; Hebel, Simon; Ross, J. Ole; Schoetter, Robert; Kalinowski, Martin B.

2013-01-01

Krypton-85 is mainly produced in nuclear reactors by fission of uranium and plutonium and released during chopping and dissolution of spent fuel rods in nuclear reprocessing facilities. As noble gas it is suited as a passive tracer for evaluation of atmospheric transport models. Furthermore, research is ongoing to assess its quality as an indicator for clandestine reprocessing activities. This paper continues previous efforts to compile a comprehensive historic emission inventory for krypton-85. Reprocessing facilities are the by far largest emitters of krypton-85. Information on sources and calculations used to derive the annual krypton-85 emission is provided for all known reprocessing facilities in the world. In addition, the emission characteristics of two plants, Tokai (Japan) and La Hague (France), are analysed in detail using emission data with high temporal resolution. Other types of krypton-85 sources are power reactors, naval reactors and isotope production facilities. These sources contribute only little or negligible amounts of krypton-85 compared to the large reprocessing facilities. Taking the decay of krypton-85 into account, the global atmospheric inventory is estimated to about 5500 PBq at the end of 2009. The correctness if the inventory has been proven by meteorological simulations and its error is assumed to be in the range of a few percent. - Highlights: ► Krypton-85 is mainly produced in nuclear reactors and released during reprocessing. ► Krypten-85 can be possibly used as an indicator for clandestine reprocessing. ► This work provides an up-to-date global krypton-85 emission inventory. ► The inventory includes emissions from all possible artificial sources.

Unlocking the forest inventory data: relating individual tree performance to unmeasured environmental factors

Science.gov (United States)

Jeremy W. Lichstein; Jonathan Dushoff; Kiona Ogle; Anping Chen; Drew W. Purves; John P. Caspersen; Stephen W. Pacala

2010-01-01

Geographically extensive forest inventories, such as the USDA Forest Service's Forest Inventory and Analysis (FIA) program, contain millions of individual tree growth and mortality records that could be used to develop broad-scale models of forest dynamics. A limitation of inventory data, however, is that individual-level measurements of light (L) and other...

Determination of fission gas release of spent nuclear fuel in puncturing test and in leaching experiments under anoxic conditions

Energy Technology Data Exchange (ETDEWEB)

González-Robles, E., E-mail: ernesto.gonzalez-robles@kit.edu [Karlsruhe Institute of Technology, Institute for Nuclear Waste Disposal (KIT-INE), P.O. Box 3640, D-76021, Karlsruhe (Germany); Metz, V. [Karlsruhe Institute of Technology, Institute for Nuclear Waste Disposal (KIT-INE), P.O. Box 3640, D-76021, Karlsruhe (Germany); Wegen, D.H. [European Commission, Joint Research Centre, Institute for Transuranium Elements (JRC-ITU), P.O. Box 2340, 76125, Karlsruhe (Germany); Herm, M. [Karlsruhe Institute of Technology, Institute for Nuclear Waste Disposal (KIT-INE), P.O. Box 3640, D-76021, Karlsruhe (Germany); Papaioannou, D. [European Commission, Joint Research Centre, Institute for Transuranium Elements (JRC-ITU), P.O. Box 2340, 76125, Karlsruhe (Germany); Bohnert, E. [Karlsruhe Institute of Technology, Institute for Nuclear Waste Disposal (KIT-INE), P.O. Box 3640, D-76021, Karlsruhe (Germany); Gretter, R. [European Commission, Joint Research Centre, Institute for Transuranium Elements (JRC-ITU), P.O. Box 2340, 76125, Karlsruhe (Germany); Müller, N. [Karlsruhe Institute of Technology, Institute for Nuclear Waste Disposal (KIT-INE), P.O. Box 3640, D-76021, Karlsruhe (Germany); Nasyrow, R.; Weerd, W. de; Wiss, T. [European Commission, Joint Research Centre, Institute for Transuranium Elements (JRC-ITU), P.O. Box 2340, 76125, Karlsruhe (Germany); Kienzler, B. [Karlsruhe Institute of Technology, Institute for Nuclear Waste Disposal (KIT-INE), P.O. Box 3640, D-76021, Karlsruhe (Germany)

2016-10-15

During reactor operation the fission gases Kr and Xe are formed within the UO{sub 2} matrix of nuclear fuel. Their quantification is important to evaluate their impact on critical parameters regarding the fuel behaviour during irradiation and (long-term) interim storage, such as internal pressure of the fuel rod and fuel swelling. Moreover the content of Kr and Xe in the plenum of a fuel rod and their content in the UO{sub 2} fuel itself are widely used as indicators for the release properties of {sup 129}I, {sup 137}Cs, and other safety relevant radionuclides with respect to final disposal of spent nuclear fuel. The present study deals with the fission gas release from spent nuclear fuel exposed to simulated groundwater in comparison with the fission gas previously released to the fuel rod plenum during irradiation in reactor. In a unique approach we determined both the Kr and Xe inventories in the plenum by means of a puncturing test and in leaching experiments with a cladded fuel pellet and fuel fragments in bicarbonate water under 3.2 bar H{sub 2} overpressure. The fractional inventory of the fission gases released during irradiation into the plenum was (8.3 ± 0.9) %. The fraction of inventory of fission gases released during the leaching experiments was (17 ± 2) % after 333 days of leaching of the cladded pellet and (25 ± 2) % after 447 days of leaching of the fuel fragments, respectively. The relatively high release of fission gases in the experiment with fuel fragments was caused by the increased accessibility of water to the Kr and Xe occluded in the fuel.

Development of the Informing Relatives Inventory (IRI): Assessing Index Patients' Knowledge, Motivation and Self-Efficacy Regarding the Disclosure of Hereditary Cancer Risk Information to Relatives.

Science.gov (United States)

de Geus, Eveline; Aalfs, Cora M; Menko, Fred H; Sijmons, Rolf H; Verdam, Mathilde G E; de Haes, Hanneke C J M; Smets, Ellen M A

2015-08-01

Despite the use of genetic services, counselees do not always share hereditary cancer information with at-risk relatives. Reasons for not informing relatives may be categorized as a lack of: knowledge, motivation, and/or self-efficacy. This study aims to develop and test the psychometric properties of the Informing Relatives Inventory, a battery of instruments that intend to measure counselees' knowledge, motivation, and self-efficacy regarding the disclosure of hereditary cancer risk information to at-risk relatives. Guided by the proposed conceptual framework, existing instruments were selected and new instruments were developed. We tested the instruments' acceptability, dimensionality, reliability, and criterion-related validity in consecutive index patients visiting the Clinical Genetics department with questions regarding hereditary breast and/or ovarian cancer or colon cancer. Data of 211 index patients were included (response rate = 62%). The Informing Relatives Inventory (IRI) assesses three barriers in disclosure representing seven domains. Instruments assessing index patients' (positive) motivation and self-efficacy were acceptable and reliable and suggested good criterion-related validity. Psychometric properties of instruments assessing index patients knowledge were disputable. These items were moderately accepted by index patients and the criterion-related validity was weaker. This study presents a first conceptual framework and associated inventory (IRI) that improves insight into index patients' barriers regarding the disclosure of genetic cancer information to at-risk relatives. Instruments assessing (positive) motivation and self-efficacy proved to be reliable measurements. Measuring index patients knowledge appeared to be more challenging. Further research is necessary to ensure IRI's dimensionality and sensitivity to change.

Experiments to Measure Hydrogen Release from Graphite Walls During Disruptions in DIII-D

International Nuclear Information System (INIS)

Hollmann, E.M.; Pablant, N.A.; Rudakov, D.L.; Boedo, J.A.; Brooks, N.H.; Jernigan, Thomas C.; Pigarov, A.Y.

2009-01-01

Spectroscopy and wall the bake-out measurements are performed in the DIII-D tokamak to estimate the amount of hydrogen stored in and released from the walls during disruptions. Both naturally occurring disruptions and disruptions induced by massive gas injection (MGI) are investigated. The measurements indicate that both types of disruptions cause a net release of order 10(21) hydrogen (or deuterium) atoms from the graphite walls. This is comparable to the pre-disruptions plasma particle inventory, so the released hydrogen is important for accurate modeling of disruptions. However, the amount of hydrogen released is small compared to the total saturated wall inventory of order 10(22)-10(23), So it appears that many disruptions are necessary to provide full pump-out of the vessel walls. (C) 2009 Published by Elsevier B.V.

Inventory of greenhouse gases emissions from gasoline and diesel ...

African Journals Online (AJOL)

Emissions from fossil fuel combustion are of global concern due to their negative effects on public health and environment. This paper is an inventory of the greenhouse gases (GHGs) released into the environment through consumption of fuels (gasoline and diesel) in Nigeria from 1980 to 2014. The fuel consumption data ...

Examining the Criterion-Related Validity of the Pervasive Developmental Disorder Behavior Inventory

Science.gov (United States)

McMorris, Carly A.; Perry, Adrienne

2015-01-01

The Pervasive Developmental Disorder Behavior Inventory is a questionnaire designed to aid in the diagnosis of pervasive developmental disorders or autism spectrum disorders. The Pervasive Developmental Disorder Behavior Inventory assesses adaptive and maladaptive behaviors associated with pervasive developmental disorders and provides an…

Hydrogen isotope inventory in the graphite divertor tiles of ASDEX Upgrade as measured by thermal desorption spectroscopy

International Nuclear Information System (INIS)

Franzen, P.; Behrisch, R.; Garcia-Rosales, C.; Schleussner, D.; Roesler, D.; Becker, J.; Knapp, W.; Edelmann, C.

1997-01-01

The hydrogen and deuterium inventories of the ASDEX Upgrade divertor tiles were measured after the experimental period from December 1994 to July 1995 by thermal desorption spectroscopy (TDS) of samples cut out of the divertor tiles. The samples were heated by electron bombardment up to 2100 K; the released gases were measured by means of a calibrated quadrupole mass spectrometer. The measured hydrogen or deuterium inventories are of the order of 10 23 m -2 . They are larger for samples of the inner divertor than of the outer divertor by a factor of about 2. The largest inventory was found at the separatrix position of the inner divertor. Most of the released hydrogen (H) can be attributed to water adsorbed in the near surface region during the air exposure prior to the TDS measurements. The total inventories measured by TDS exceed the inventories in the near surface region (< 25 μm) measured by ion beam analysis methods by a factor of up to 10. Hence, the total hydrogen retention is governed by the diffusion out of the near surface region deep into the material. The hydrogen and deuterium inventories decreased with increasing surface temperature. (author). 64 refs, 12 figs, 2 tabs

Control decisions for 3H, 14C, 85Kr, and 129I released from the commercial fuel cycle

International Nuclear Information System (INIS)

Thomas, T.R.; Brown, R.A.

1985-01-01

The effects of complete release of 3 H, 14 C, 85 Kr and 129 I from operating a 400-GWe fuel cycle for 100 years are shown. The postulated accrued health effects (HE) from 14 C and 129 I appear large; however, these numbers are insignificant when compared to the 176 billion cancer deaths that would occur from all causes in the 10,000-year reference period. The percent increase in global cancer deaths would be no greater than 5 x 10 -5 % for each of the radionuclides. Based on the 1980 inventory of each radionuclide in the environment, complete release for 100 years from a 400-GWe fuel cycle would not increase the 3 H or 14 C inventories, however, large increases in 85 Kr and 129 I inventories would occur. The effects, besides dose impacts, of large increases in inventory are unknown and serve only as warning flags that should be taken into consideration. Only 129 I releases from a fuel reprocessing plant would exceed the allowable maximum exposed individual dose limit and 85 Kr and 129 I would exceed the allowable release limit. The effects of controlled releases from commercial fuel reprocessing plants serving a 400-GWe fuel cycle for 100 years are also shown

The total release of xenon-133 from the Fukushima Dai-ichi nuclear power plant accident

International Nuclear Information System (INIS)

Stohl, Andreas; Seibert, Petra; Wotawa, Gerhard

2012-01-01

The accident at the Fukushima Dai-ichi nuclear power plant (FD-NPP) on 11 March 2011 released large amounts of radioactivity into the atmosphere. We determine the total emission of the noble gas xenon-133 ( 133 Xe) using global atmospheric concentration measurements. For estimating the emissions, we used three different methods: (i) using a purely observation-based multi-box model, (ii) comparisons of dispersion model results driven with GFS meteorological data with the observation data, and (iii) such comparisons with the dispersion model driven by ECMWF data. From these three methods, we have obtained total 133 Xe releases from FD-NPP of (i) 16.7 ± 1.9 EBq, (ii) 14.2 ± 0.8 EBq, and (iii) 19.0 ± 3.4 EBq, respectively. These values are substantially larger than the entire 133 Xe inventory of FD-NPP of about 12.2 EBq derived from calculations of nuclear fuel burn-up. Complete release of the entire 133 Xe inventory of FD-NPP and additional release of 133 Xe due to the decay of iodine-133 ( 133 I), which can add another 2 EBq to the 133 Xe FD-NPP inventory, is required to explain the atmospheric observations. Two of our three methods indicate even higher emissions, but this may not be a robust finding given the differences between our estimates. - Highlights: ► We determine the total release of xenon-133 from the Fukushima nuclear accident. ► We used global measurements and a box model, as well as dispersion model estimates. ► Total 133 Xe release is about 14.2-19 EBq, more than Fukushima 133 Xe inventory. ► Additional release of iodine-133 and decay into 133 Xe needed to explain results.

Radioactive releases into the environment under accidental conditions

International Nuclear Information System (INIS)

Beninson, D.

1976-01-01

Although accidents involving the release of radioactive materials and the unplanned exposure of people can occur at any stage of the nuclear fuel cycle, most attention has been focused on reactor accidents. Although no power reactor accidents involving exposure of the public have yet occured, it should be recognized that the probability of such accidental releases cannot be reduced to zero. Since the inventory of radioactive materials in power reactors is very large, it is usual to postulate, for safety assessments, that a release of fission products takes place in spite of all protective measures. This postulated release is of importance for reactor siting and for preparing emergency plans. (HP) [de

54Mn release from LMFBR cores

International Nuclear Information System (INIS)

Polley, M.V.

1976-10-01

The inventory of 54 Mn per unit exposed area of stainless steel in LMFBR cores may be calculated using a formula originally derived at HEDL. This treats the simultaneous production by activation and release by corrosion and diffusion of 54 Mn and assumes that the concentration at the steel surface is zero. The inventory per unit exposed area is calculated as a function of temperature and is compared with that calculated simply by assuming stoichiometric corrosion. An effective diffusion coefficient is used in the calculations which include contributions from both lattice and grain boundary diffusion. A general relationship is derived for the effective diffusion coefficient and it is shown how values may be obtained using the Levine-MacCallum and the Fisher theories of grain boundary diffusion. Values of the lattice diffusion coefficient were obtained by analysing data obtained from sodium loop experiments. The effect on the inventory due to the possible formation of a ferrite layers on the exposed surface is discussed and it is also shown how the inventory over several fuel cycles may be calculated. (U.K.)

Effect of surface water on tritium release behavior from Li4SiO4

International Nuclear Information System (INIS)

Hanada, T.; Fukada, S.; Nishikawa, M.; Suematsu, K.; Yamashita, N.; Kanazawa, T.

2010-01-01

The tritium release model to represent the release behavior of bred tritium from solid breeder materials has been developed by the blanket group of Kyushu University. It has been found that water is released to the purge gas from solid breeder materials and that this water affects the tritium release behavior. In this study, the amount of surface water released from Li 4 SiO 4 is quantified by the experiment. In addition, the tritium release behavior from Li 4 SiO 4 are estimated based on the tritium release model using parameters obtained in our studies under conditions of commercial reactor operation and ITER test blanket module operation. The effect of the surface water on tritium release behavior is discussed from the obtained results. Moreover, the tritium inventory of Li 4 SiO 4 is discussed based on calculation under the unsteady state condition. Further, the effects of grain size and temperature on distribution of tritium inventory under the steady state condition are evaluated, and the optimal grain size is discussed from the view point of tritium release from Li 4 SiO 4 .

Inventory Control System by Using Vendor Managed Inventory (VMI)

Science.gov (United States)

Sabila, Alzena Dona; Mustafid; Suryono

2018-02-01

The inventory control system has a strategic role for the business in managing inventory operations. Management of conventional inventory creates problems in the stock of goods that often runs into vacancies and excess goods at the retail level. This study aims to build inventory control system that can maintain the stability of goods availability at the retail level. The implementation of Vendor Managed Inventory (VMI) method on inventory control system provides transparency of sales data and inventory of goods at retailer level to supplier. Inventory control is performed by calculating safety stock and reorder point of goods based on sales data received by the system. Rule-based reasoning is provided on the system to facilitate the monitoring of inventory status information, thereby helping the process of inventory updates appropriately. Utilization of SMS technology is also considered as a medium of collecting sales data in real-time due to the ease of use. The results of this study indicate that inventory control using VMI ensures the availability of goods ± 70% and can reduce the accumulation of goods ± 30% at the retail level.

An Integer Programming Model for Multi-Echelon Supply Chain Decision Problem Considering Inventories

Science.gov (United States)

Harahap, Amin; Mawengkang, Herman; Siswadi; Effendi, Syahril

2018-01-01

In this paper we address a problem that is of significance to the industry, namely the optimal decision of a multi-echelon supply chain and the associated inventory systems. By using the guaranteed service approach to model the multi-echelon inventory system, we develop a mixed integer; programming model to simultaneously optimize the transportation, inventory and network structure of a multi-echelon supply chain. To solve the model we develop a direct search approach using a strategy of releasing nonbasic variables from their bounds, combined with the “active constraint” method. This strategy is used to force the appropriate non-integer basic variables to move to their neighbourhood integer points.

Eating-related Intrusive Thoughts Inventory: exploring the dimensionality of eating disorder symptoms.

Science.gov (United States)

Perpiñá, Conxa; Roncero, María; Belloch, Amparo; Sánchez-Reales, Sergio

2011-08-01

The aims of this study were, first, to examine the structure and validity of the Eating-related Intrusive Thoughts Inventory (INPIAS), a self-report questionnaire designed to assess eating disorders related to intrusive thoughts (EDITs), and second, to explore the existence of a continuum ranging from normal to abnormal thought intrusions related to eating, weight, and shape. Participants were 574 (408 women) nonclinical community individuals. Analyses revealed that EDITs can be clustered into three sets: appearance-dieting, need to exercise, and thoughts-impulses related to eating disorders. EDITs' consequences showed a two-factor structure: emotional consequences/personal meaning and thought-action fusion responsibility; and four factors of strategies: "anxiety," suppression, obsessive-compulsive rituals, and distraction. The sample was then divided according to reported restrained eating. The High dietary restraint group reported a higher frequency of EDITs, whereas differences in the other factors were mediated by depression, anxiety, and obsessionality. The results suggest that eating disorder-related cognitions are experienced by nonclinical individuals, and distributed on a continuum.

Ottawa National Wildlife Refuge : Wildlife Inventory Plan

Data.gov (United States)

Department of the Interior — This Wildlife Inventory Plan for Ottawa NWR describes the inventory program’s relation to Refuge objectives and outlines the program’s policies and administration....

Enhancing criterion-related validity through bottom-up contextualization of personality inventories: The construction of an ecological conscientiousness scale

NARCIS (Netherlands)

dr René Butter; Marise Born

2011-01-01

In this paper the concept of "ecological personality scales" is introduced. These are contextualized inventories with a high ecological validity. They are developed in a bottom-up or qualitative way and combine a relatively high trait specificity with a relatively high situational specificity. An

Designing Intelligent Secure Android Application for Effective Chemical Inventory

Science.gov (United States)

Shukran, Mohd Afizi Mohd; Naim Abdullah, Muhammad; Nazri Ismail, Mohd; Maskat, Kamaruzaman; Isa, Mohd Rizal Mohd; Shahfee Ishak, Muhammad; Adib Khairuddin, Muhamad

2017-08-01

Mobile services support various situations in everyday life and with the increasing sophistication of phone functions, the daily life is much more easier and better especially in term of managing tools and apparatus. Since chemical inventory management system has been experiencing a new revolution from antiquated to an automated inventory management system, some additional features should be added in current chemical inventory system. Parallel with the modern technologies, chemical inventory application using smart phone has been developed. Several studies about current related chemical inventory management using smart phone application has been done in this paper in order to obtain an overview on recent studies in smartphone application for chemical inventory system which are needed in schools, universities or other education institutions. This paper also discuss about designing the proposed secure mobile chemical inventory system. The study of this paper can provide forceful review analysis support for the chemical inventory management system related research.

Transient fission product release during reactor shutdown and startup

International Nuclear Information System (INIS)

Hunt, C.E.L.; Lewis, B.J.

1995-01-01

Sweep gas experiments performed at CRL from 1979 to 1985 have been analysed to determine the fraction of the fission product gas inventory that is released on reactor shutdown and startup. Empirical equations were derived and applied to calculate the xenon release from companion fuel elements and from a well documented experimental fuel bundle irradiated in the NRU reactor. The measured gas release could be matched to within about a factor of two for an experimental irradiation with a burnup of 217 MWh/kgU. (author)

Inventory Control System by Using Vendor Managed Inventory (VMI

Directory of Open Access Journals (Sweden)

Dona Sabila Alzena

2018-01-01

Full Text Available The inventory control system has a strategic role for the business in managing inventory operations. Management of conventional inventory creates problems in the stock of goods that often runs into vacancies and excess goods at the retail level. This study aims to build inventory control system that can maintain the stability of goods availability at the retail level. The implementation of Vendor Managed Inventory (VMI method on inventory control system provides transparency of sales data and inventory of goods at retailer level to supplier. Inventory control is performed by calculating safety stock and reorder point of goods based on sales data received by the system. Rule-based reasoning is provided on the system to facilitate the monitoring of inventory status information, thereby helping the process of inventory updates appropriately. Utilization of SMS technology is also considered as a medium of collecting sales data in real-time due to the ease of use. The results of this study indicate that inventory control using VMI ensures the availability of goods ± 70% and can reduce the accumulation of goods ± 30% at the retail level.

Validation of the ORIGEN-S code for predicting radionuclide inventories in used CANDU fuel

International Nuclear Information System (INIS)

Tait, J.C.; Gauld, I.; Kerr, A.H.

1995-01-01

The safety assessment being conducted by AECL Research for the concept of deep geological disposal of used CANDU UO 2 fuel requires the calculation of radionuclide inventories in the fuel to provide source terms for radionuclide release. This report discusses the validation of selected actinide and fission-product inventories calculated using the ORIGEN-S code coupled with the WIMS-AECL lattice code, using data from analytical measurements of radioisotope inventories in Pickering CANDU reactor fuel. The recent processing of new ENDF/B-VI cross-section data has allowed the ORIGEN-S calculations to be performed using the most up-to-date nuclear data available. The results indicate that the code is reliably predicting actinide and the majority of fission-product inventories to within the analytical uncertainty. ((orig.))

Inventory Control System by Using Vendor Managed Inventory (VMI)

OpenAIRE

Dona Sabila Alzena; Mustafid Mustafid; Suryono Suryono

2018-01-01

The inventory control system has a strategic role for the business in managing inventory operations. Management of conventional inventory creates problems in the stock of goods that often runs into vacancies and excess goods at the retail level. This study aims to build inventory control system that can maintain the stability of goods availability at the retail level. The implementation of Vendor Managed Inventory (VMI) method on inventory control system provides transparency of sales data an...

An inventory of potential PCDD and PCDF emission sources in the mainland of China

Energy Technology Data Exchange (ETDEWEB)

Jin, Jun; Xiaoyan, Tang [Peking Univ., Beijing (China); Peng, Hao [Central Univ. for Nationalities, Beijing (China)

2004-09-15

Polychlorinated dibenzo-p-dioxin (PCDD) and polychlorinated dibenzofurans (PCDF) are widespread environmental pollutants. A number of countries have developed national inventories of PCDD/F emission, such as USA, EU Nations and Japan. However, due to the lack of PCDD/F data measured in China and the uncertain nature of the documentation available on emission factors, the report on inventories of dioxin emission is absent. With the municipal population growth, economic development and living-standard improvement, China faces many severe environment issues including potential problems related to PCDD/F. The country is aware of potential dioxin sources such as: incineration, iron and steel industry, chemical industry, fires, coal power plant, foundries, PCB in capacitors and transformers, sintering, traffic emission. In 2001, China signed the Stockholm Convention on Persistent Organic Pollutants in Stockholm. Therefore, there is a need for information regarding dioxin emission from these sources for taking actions to reduce and/or eliminate the release of dioxins in China, and reduce human exposure. In this study, we identify those potential PCDD/F emission sources and work out the first inventory on PCDD/F emission into the environment in China.

Purchasing and inventory management techniques for optimizing inventory investment

International Nuclear Information System (INIS)

McFarlane, I.; Gehshan, T.

1993-01-01

In an effort to reduce operations and maintenance costs among nuclear plants, many utilities are taking a closer look at their inventory investment. Various approaches for inventory reduction have been used and discussed, but these approaches are often limited to an inventory management perspective. Interaction with purchasing and planning personnel to reduce inventory investment is a necessity in utility efforts to become more cost competitive. This paper addresses the activities that purchasing and inventory management personnel should conduct in an effort to optimize inventory investment while maintaining service-level goals. Other functions within a materials management organization, such as the warehousing and investment recovery functions, can contribute to optimizing inventory investment. However, these are not addressed in this paper because their contributions often come after inventory management and purchasing decisions have been made

Measurement of gap and grain-boundary inventories of 129I in used CANDU fuels

International Nuclear Information System (INIS)

Stroes-Gascoyne, S.; Moir, D.L.; Kolar, M.; Porth, R.J.; McConnell, J.L.; Kerr, A.H.

1995-01-01

Combined gap and grain-boundary inventories of 129 I in 14 used CANDU fuel elements were measured by crushing and simultaneously leaching fuel segments for 4 h in a solution containing KI carrier. From analogy with previous work a near one-to-one correlation was anticipated between the amount of stable Xe and the amount of 128 I in the combined gap and grain-boundary regions of the fuel. However, the results showed that such a correlation was only apparent for low linear power rating (LLPR) fuels with an average linear power rating of 44 kW/m), the 129 I values were considerably smaller than expected. The combined gap and grain-boundary inventories of 129 I in the 14 fuels tested varied from 1.8 to 11.0%, with an average value of 3.6 ± 2.4% which suggests that the average value of 8.1 ± 1% used in safety assessment calculations overestimates the instant release fraction for 129 I. Segments of used CANDU fuels were leached for 92 d (samples taken at 5, 28 and 92 d) to determine the kinetics of 129 I release. Results could be fitted tentatively to half-order reaction kinetics, implying that 129 I release is a diffusion-controlled process for LLPR fuels, and also for HLPR fuels, once the gap inventory has been leached. However, more data are needed over longer leaching periods to gain more understanding of the processes that control grain-boundary release of 129 I from used CANDU fuel

Study of Intelligent Secure Chemical Inventory Management System

Science.gov (United States)

Shukran, Mohd Afizi Mohd; Naim Abdullah, Muhammad; Nazri Ismail, Mohd; Maskat, Kamaruzaman; Isa, Mohd Rizal Mohd; Shahfee Ishak, Muhammad; Adib Khairuddin, Muhamad

2017-08-01

Chemical inventory management system has been experiencing a new revolution from traditional inventory system which is manual to an automated inventory management system. In this paper, some review of the classic and modern approaches to chemical inventory management system has been discussed. This paper also describe about both type of inventory management. After a comparative analysis of the traditional method and automated method, it can be said that both methods have some distinctive characteristics. Moreover, the automated inventory management method has higher accuracy of calculation because the calculations are handled by software, eliminating possible errors and saving time. The automated inventory system also allows users and administrators to track the availability, location and consumption of chemicals. The study of this paper can provide forceful review analysis support for the chemical inventory management related research.

Increased release of histamine in patients with respiratory symptoms related to perfume

DEFF Research Database (Denmark)

Elberling, J; Skov, P S; Mosbech, H

2007-01-01

BACKGROUND: Environmental perfume exposure may cause respiratory symptoms. Individuals with asthma and perfume contact allergy report such symptoms more frequently than others. However, immunologic mechanisms have not been demonstrated and the symptoms are not associated with IgE-mediated allergy....... The study aimed to investigate whether basophils from patients with respiratory symptoms related to perfume released more histamine in the presence of perfume as compared with healthy volunteers. METHODS: Histamine release was measured by the glass fibre method. Blood was obtained from healthy volunteers (n......=20) and patients with respiratory symptoms related to perfume (n=17) attending a dermatological outpatient clinic for patch testing. The effect of an international brand perfume was investigated using the basophil histamine release test with perfume. Furthermore, basophils from a healthy non...

Optimization of Inventory

OpenAIRE

PROKOPOVÁ, Nikola

2017-01-01

The subject of this thesis is optimization of inventory in selected organization. Inventory optimization is a very important topic in each organization because it reduces storage costs. At the beginning the inventory theory is presented. It shows the meaning and types of inventory, inventory control and also different methods and models of inventory control. Inventory optimization in the enterprise can be reached by using models of inventory control. In the second part the company on which is...

Determining an optimum inventory route for an areal object: the case of forest inventory in Finland

Directory of Open Access Journals (Sweden)

Henna Etula

2014-03-01

Full Text Available In recent decades, routing based on Geographic Information Systems (GIS has become a major branch of technology, which has been used especially in applications related to transport and logistics. However, in terms of the development of methods, routing in a cross-country environment is more difficult, and hence research into it has been relatively scarce. This is particularly true in the context of complex routing problems involving visits to several locations. A typical example of a problem of this kind is field inventory, which is a data collection procedure used in many application areas, particularly those related to environmental research and the management of natural resources. This study presents a problem in which an efficient inventory route is determined for an areal object, such that the area visible from the route meets a prescribed threshold, while maintaining the shortest possible route. Although this problem, referred to here as the Areal Inventory Problem (AIP, is closely related to a multitude of routing and location allocation methods known in the context of GIS, none of them is very well-suited for solving the AIP. This study describes a general solution procedure for the AIP, and introduces an implementation of a heuristic algorithm that can be used to solve a real-world AIP within a reasonable time frame. The proposed approach is demonstrated with actual data related to field inventory practices carried out by the Finnish Forest Centre.

A user's guide to the reactor inventory module NECTAR-RICE

International Nuclear Information System (INIS)

Barker, C.D.

1982-01-01

The NECTAR environmental computer code has been developed to meet the increasing demand for comprehensive calculations of the radiological consequences of the atmosphere release of radionuclides from a nuclear facility. The code consists of a main control program, library listing/modification routines and five calculational modules. The input data required for the reactor inventory module NECTAR-RICE is described. This data includes facilities for specifying the initial conditions, controlling the irradiation conditions of the fuel and for temporarily modifying library data at different stages of the calculation. The structure of the module is briefly described and three sample cases are given to facilitate understanding of the program's use and program testing. These sample cases demonstrate the three different ways of running the program, namely to calculate actinide inventories only, fission product inventories only or to do a composite actinide and fission product calculation. (author)

Validation of the ORIGEN-S code for predicting radionuclide inventories in used CANDU Fuel

International Nuclear Information System (INIS)

Tait, J.C.; Gauld, I.; Kerr, A.H.

1994-10-01

The safety assessment being conducted by AECL Research for the concept of deep geological disposal of used CANDU UO 2 fuel requires the calculation of radionuclide inventories in the fuel to provide source terms for radionuclide release. This report discusses the validation of selected actinide and fission-product inventories calculated using the ORIGEN-S code coupled with the WIMS-AECL lattice code, using data from analytical measurements of radioisotope inventories in Pickering CANDU reactor fuel. The recent processing of new ENDF/B-VI cross-section data has allowed the ORIGEN-S calculations to be performed using the most up-to-date nuclear data available. The results indicate that the code is reliably predicting actinide and the majority of fission-product inventories to within the analytical uncertainty. 38 refs., 4 figs., 5 tabs

Joint inventory control and pricing in a service-inventory system

DEFF Research Database (Denmark)

Marand, Ata Jalili; Li, Hongyan Jenny; Thorstenson, Anders

2017-01-01

This study addresses joint inventory control and pricing decisions for a service-inventory system. In such a system both an on-hand inventory item and a positive service time are required to fulfill customer demands. The service-inventory system also captures main features of the classical...... inventory systems with a positive processing time, e.g., make-to-order systems. In this study, the service-inventory system is modeled as an M/M/1 queue in which the customer arrival rate is price dependent. The inventory of an individual item is continuously reviewed under an (r,Q) policy....... The replenishment lead times of the inventory are exponentially distributed. Furthermore, customers arriving during stock-out periods are lost. The stochastic customer inter-arrival times, service times, and inventory replenishment lead times cause the high complexity of the problem and the difficulty in solving it...

The Coopersmith Self-Esteem Inventory Related to Academic Achievement and School Behavior. Interim Research Report # 23.

Science.gov (United States)

Rubin, Rosalyn; And Others

Scores on the Coopersmith Self-Esteem Inventory were related to scores on achievement and intelligence tests, and to socioeconomic level and to teachers' ratings of student behavior, in order to test the hypothesis that student self esteem would have a positive effect on academic achievement. There was a small but statistically significant…

Inventory of Federal energy-related environment and safety research for FY 1979. Volume 1. Executive summary

International Nuclear Information System (INIS)

1980-12-01

The FY 1979 Federal Inventory contains information on 3506 federally funded energy-related environmental and safety research projects. The Inventory is published in two volumes: Volume I, an executive summary and overview of the data and Volume II, project listings, summaries, and indexes. Research and development (R and D) categories were reorganized into three main areas; environmental and safety control technology, technology impacts overview and assessments, and biological and environmental R and D and assessments. Federal offices submitting project data were: Council on Environmental Quality; Department of Agriculture; Department of Commerce; Department of Defense; Department of Energy; Department of Health, Education, and Welfare; Department of Housing and Urban Development; Department of the Interior; Department of Transportation; Environmental Protection Agency; National Aeronautics and Space Administration; Nuclear Regulatory Commission; National Science Foundation; Office of Technology Assessment; and Tennessee Valley Authority. The inventory also breaks out research sponsored by various federal agencies and the amount of funding provided by each in various research categories. The format and index system allows efficient access to information compiled. Users are able to identify projects by log agency, performing organization, principal investigator and subject

U.S. Navy Ships Food Service Divisions: Modernizing Inventory Management

Science.gov (United States)

2010-06-01

management procedures for receipt, inventory, stowage, and issue of provisions onboard ships have remained relatively unchanged for decades. Culinary ...improve the quality of life for Culinary Specialists 15. NUMBER OF PAGES 87 14. SUBJECT TERMS Inventory management , records keeper, stores onload...remained relatively unchanged for decades. Culinary Specialists are utilizing an antiquated and unreliable inventory management program (the Food

Calculations in support of a potential definition of large release

International Nuclear Information System (INIS)

Hanson, A.L.; Davis, R.E.; Mubayi, V.

1994-05-01

The Nuclear Regulatory Commission has stated a hierarchy of safety goals with the qualitative safety goals as Level I of the hierarchy, backed up by the quantitative health objectives as Level II and the large release guideline as Level III. The large release guideline has been stated in qualitative terms as a magnitude of release of the core inventory whose frequency should not exceed 10 -6 per reactor year. However, the Commission did not provide a quantitative specification of a large release. This report describes various specifications of a large release and focuses, in particular, on an examination of releases which have a potential to lead to one prompt fatality in the mean. The basic information required to set up the calculations was derived from the simplified source terms which were obtained from approximations of the NUREG-1150 source terms. Since the calculation of consequences is affected by a large number of assumptions, a generic site with a (conservatively determined) population density and meteorology was specified. At this site, various emergency responses (including no response) were assumed based on information derived from earlier studies. For each of the emergency response assumptions, a set of calculations were performed with the simplified source terms; these included adjustments to the source terms, such as the timing of the release, the core inventory, and the release fractions of different radionuclides, to arrive at a result of one mean prompt fatality in each case. Each of the source terms, so defined, has the potential to be a candidate for a large release. The calculations show that there are many possible candidate source terms for a large release depending on the characteristics which are felt to be important

Canadian pollutant releases and transfers : NPRI data 1998

International Nuclear Information System (INIS)

2001-03-01

A large, two-sided fold-out poster showing pollution hotspots throughout Canada, has been released by the Canadian Institute for Environmental Law and Policy (CIELAP). The poster is based on the maps and tables of the National Pollutant Release Inventory (NPRI) 1998. It presents the top on-site releases and off-site transfers of pollutants by facilities across Canada, and provides a summary of releases, transfers and recycling of pollutants by province. The map depicts the facilities with the five largest quantities of individual pollutants released to each medium, i. e. water, air, land, underground. The crude oil and gas, other utilities, primary metal, paper and chemical industrial sectors are responsible for the largest on-site releases, while the business services, fabricated metal. primary metal and chemical industrial sectors account for the largest off-site transfers. Twenty-five of the 176 substances whose releases and transfers are reported under the NPRI are classified as 'toxic' or 'carcinogenic'. tabs., maps

LOFC fission product release and circulating activity calculations for gas-cooled reactors

International Nuclear Information System (INIS)

Apperson, C.E. Jr.; Carruthers, L.M.; Lee, C.E.

1977-01-01

The inventories of fission products in a gas-cooled reactor under accident and normal steady state conditions are time and temperature dependent. To obtain a reasonable estimate of these inventories it is necessary to consider fuel failure, a temperature dependent variable, and radioactive decay, a time dependent variable. Using arbitrary radioactive decay chains and published fuel failure models for the High Temperature Gas-Cooled Reactor (HTGR), methods have been developed to evaluate the release of fission products during the Loss of Forced Circulation (LOFC) accident and the circulating and plateout fission product inventories during steady state non-accident operation. The LARC-2 model presented here neglects the time delays in the release from the HTGR due to diffusion of fission products from particles in the fuel rod through the graphite matrix. It also neglects the adsorption and evaporation process of metallics at the fuel rod-graphite and graphite-coolant hole interfaces. Any time delay due to the finite time of transport of fission products by convection through the coolant to the outside of the prestressed concrete reactor vessel (PCRV) is also neglected. This model assumes that all fission products released from fuel particles are immediately deposited outside the PCRV with no time delay

ZZ ECN-BUBEBO, ECN-Petten Burnup Benchmark Book, Inventories, Afterheat

International Nuclear Information System (INIS)

Kloosterman, Jan Leen

1999-01-01

Description of program or function: Contains experimental benchmarks which can be used for the validation of burnup code systems and accompanied data libraries. Although the benchmarks presented here are thoroughly described in literature, it is in many cases not straightforward to retrieve unambiguously the correct input data and corresponding results from the benchmark Descriptions. Furthermore, results which can easily be measured, are sometimes difficult to calculate because of conversions to be made. Therefore, emphasis has been put to clarify the input of the benchmarks and to present the benchmark results in such a way that they can easily be calculated and compared. For more thorough Descriptions of the benchmarks themselves, the literature referred to here should be consulted. This benchmark book is divided in 11 chapters/files containing the following in text and tabular form: chapter 1: Introduction; chapter 2: Burnup Credit Criticality Benchmark Phase 1-B; chapter 3: Yankee-Rowe Core V Fuel Inventory Study; chapter 4: H.B. Robinson Unit 2 Fuel Inventory Study; chapter 5: Turkey Point Unit 3 Fuel Inventory Study; chapter 6: Turkey Point Unit 3 Afterheat Power Study; chapter 7: Dickens Benchmark on Fission Product Energy Release of U-235; chapter 8: Dickens Benchmark on Fission Product Energy Release of Pu-239; chapter 9: Yarnell Benchmark on Decay Heat Measurements of U-233; chapter 10: Yarnell Benchmark on Decay Heat Measurements of U-235; chapter 11: Yarnell Benchmark on Decay Heat Measurements of Pu-239

Examination of Mechanisms Responsible for Organic Dust-related Diseases: Mediator Release induced by Microorgansims. A review

DEFF Research Database (Denmark)

Norn, Svend; Clementsen, Paul; Kristensen, K.S.

1994-01-01

Farmakologi, org. dust-related diseases, bacteria, pathogenic mechanisms, mediator release, entoxins - fungal spores......Farmakologi, org. dust-related diseases, bacteria, pathogenic mechanisms, mediator release, entoxins - fungal spores...

Assessing clergy work-related psychological health : reliability and validity of the Francis Burnout Inventory

OpenAIRE

Francis, Leslie J.; Laycock, Patrick; Crea, Giuseppe

2017-01-01

Drawing on the classic model of balanced affect, the Francis Burnout Inventory (FBI) conceptualised good work-related psychological health among clergy in terms of negative affect being balanced by positive affect. In the FBI negative affect is assessed by the Scale of Emotional Exhaustion in Ministry (SEEM) and positive affect is assessed by the Satisfaction in Ministry Scale (SIMS). In support of the idea of balanced affect, previous work had shown a significant interaction between the effe...

A logical framework for ranking landslide inventory maps

Science.gov (United States)

Santangelo, Michele; Fiorucci, Federica; Bucci, Francesco; Cardinali, Mauro; Ardizzone, Francesca; Marchesini, Ivan; Cesare Mondini, Alessandro; Reichenbach, Paola; Rossi, Mauro; Guzzetti, Fausto

2014-05-01

Landslides inventory maps are essential for quantitative landslide hazard and risk assessments, and for geomorphological and ecological studies. Landslide maps, including geomorphological, event based, multi-temporal, and seasonal inventory maps, are most commonly prepared through the visual interpretation of (i) monoscopic and stereoscopic aerial photographs, (ii) satellite images, (iii) LiDAR derived images, aided by more or less extensive field surveys. Landslide inventory maps are the basic information for a number of different scientific, technical and civil protection purposes, such as: (i) quantitative geomorphic analyses, (ii) erosion studies, (iii) deriving landslide statistics, (iv) urban development planning (v) landslide susceptibility, hazard and risk evaluation, and (vi) landslide monitoring systems. Despite several decades of activity in landslide inventory making, still no worldwide-accepted standards, best practices and protocols exist for the ranking and the production of landslide inventory maps. Standards for the preparation (and/or ranking) of landslide inventories should indicate the minimum amount of information for a landslide inventory map, given the scale, the type of images, the instrumentation available, and the available ancillary data. We recently attempted at a systematic description and evaluation of a total of 22 geomorphological inventories, 6 multi-temporal inventories, 10 event inventories, and 3 seasonal inventories, in the scale range between 1:10,000 and 1:500,000, prepared for areas in different geological and geomorphological settings. All of the analysed inventories were carried out by using image interpretation techniques, or field surveys. Firstly, a detailed characterisation was performed for each landslide inventory, mainly collecting metadata related (i) to the amount of information used for preparing the landslide inventory (i.e. images used, instrumentation, ancillary data, digitalisation method, legend, validation

Inventory management systems : Control and information issues

NARCIS (Netherlands)

Janssen, F.B.S.L.P.

1998-01-01

This dissertation addresses the management of inventory systems. The thesis starts with an exposition on mathematical models that can be used in inventory theory. Then we deal with some information issues related to the demand process. Namely, how to control products that have intermittent demand.

Inventory of environmental impact models related to energy technologies

Energy Technology Data Exchange (ETDEWEB)

Owen, P.T.; Dailey, N.S.; Johnson, C.A.; Martin, F.M. (eds.)

1979-02-01

The purpose of this inventory is to identify and collect data on computer simulations and computational models related to the environmental effects of energy source development, energy conversion, or energy utilization. Information for 33 data fields was sought for each model reported. All of the information which could be obtained within the time alloted for completion of the project is presented for each model listed. Efforts will be continued toward acquiring the needed information. Readers who are interested in these particular models are invited to contact ESIC for assistance in locating them. In addition to the standard bibliographic information, other data fields of interest to modelers, such as computer hardware and software requirements, algorithms, applications, and existing model validation information, are included. Indexes are provided for contact person, acronym, keyword, and title. The models are grouped into the following categories: atmospheric transport, air quality, aquatic transport, terrestrial food chains, soil transport, aquatic food chains, water quality, dosimetry, and human effects, animal effects, plant effects, and generalized environmental transport. Within these categories, the models are arranged alphabetically by last name of the contact person.

Inventory of environmental impact models related to energy technologies

International Nuclear Information System (INIS)

Owen, P.T.; Dailey, N.S.; Johnson, C.A.; Martin, F.M.

1979-02-01

The purpose of this inventory is to identify and collect data on computer simulations and computational models related to the environmental effects of energy source development, energy conversion, or energy utilization. Information for 33 data fields was sought for each model reported. All of the information which could be obtained within the time alloted for completion of the project is presented for each model listed. Efforts will be continued toward acquiring the needed information. Readers who are interested in these particular models are invited to contact ESIC for assistance in locating them. In addition to the standard bibliographic information, other data fields of interest to modelers, such as computer hardware and software requirements, algorithms, applications, and existing model validation information, are included. Indexes are provided for contact person, acronym, keyword, and title. The models are grouped into the following categories: atmospheric transport, air quality, aquatic transport, terrestrial food chains, soil transport, aquatic food chains, water quality, dosimetry, and human effects, animal effects, plant effects, and generalized environmental transport. Within these categories, the models are arranged alphabetically by last name of the contact person

Chinese version of the separation-individuation inventory.

Science.gov (United States)

Tam, Wai-Cheong Carl; Shiah, Yung-Jong; Chiang, Shih-Kuang

2003-08-01

The importance of the separation-individuation process in object relations theory is well known in disciplines of psychology, counseling, and human development. Based on the Separation-Individuation Inventory of Christenson and Wilson, which measures the manifestations of disturbances in this process, a Chinese version of the inventory was developed. For college students Cronbach coefficient alpha was .89, and test-retest reliability over 28 days was .77. The scores of the inventory had positive correlations with both the number of borderline personality characteristics and the Individualism-Collectivism Scale, respectively. Also, the mean score on the inventory of patients diagnosed with borderline personality disorder was significantly higher than that of the two normal control groups (ns = 564). Thus the inventory possessed satisfactory construct validity. Cultural differences regarding the separation-individuation process need to be investigated further.

Derivation of a radionuclide inventory for irradiated graphite-chlorine-36 inventory determination

International Nuclear Information System (INIS)

Brown, F.J.; Palmer, J.D.; Wood, P.

2001-01-01

fraction of the chlorine is released from the graphite during irradiation, both in natural precursor and activated form. The release rate of inactive chlorine and of chlorine-36 was modelled, to allow the calculation of a residual chlorine-36 inventory in operational and decommissioning wastes; actual measurements on operational wastes have confirmed this release. This has subsequently been used to assess the effect on disposal risks. This paper provides a description of the work undertaken by Nirex to establish the residual inventory of chlorine-36 in irradiated nuclear graphite, and outline the implications for disposal of these wastes. (author)

The release of fission products from uranium metal: a review

International Nuclear Information System (INIS)

Minshall, P.C.

1989-03-01

The literature on the release of fission products as gaseous species from irradiated uranium metal in oxidising atmospheres has been reviewed. Release of actinides and of fission products as spalled particulate were not considered. Data is given on the release in air, carbon dioxide, steam and mixtures of steam and air. The majority of data discussed lie between 800 and 1200 0 C though some results for xenon, krypton and iodine releases below 800 0 C are given. Two measures of fission product release are discussed: the release fraction, F(tot), which is the ratio of the total release to the initial inventory, and the fractional release, F(ox), which is the fraction released from the oxidised metal. The effect of burn-up, atmosphere and temperature on F(tot) and F(ox) is examined and the conditions under which the release fraction, F(tot) is proportional to the extent of oxidation discussed. (author)

Applying inventory classification to a large inventory management system

Directory of Open Access Journals (Sweden)

Benjamin Isaac May

2017-06-01

Full Text Available Inventory classification aims to ensure that business-driving inventory items are efficiently managed in spite of constrained resources. There are numerous single- and multiple-criteria approaches to it. Our objective is to improve resource allocation to focus on items that can lead to high equipment availability. This concern is typical of many service industries such as military logistics, airlines, amusement parks and public works. Our study tests several inventory prioritization techniques and finds that a modified multi-criterion weighted non-linear optimization (WNO technique is a powerful approach for classifying inventory, outperforming traditional techniques of inventory prioritization such as ABC analysis in a variety of performance objectives.

Fission Product Release from Spent Nuclear Fuel During Melting

International Nuclear Information System (INIS)

Howell, J.P.; Zino, J.F.

1998-09-01

The Melt-Dilute process consolidates aluminum-clad spent nuclear fuel by melting the fuel assemblies and diluting the 235U content with depleted uranium to lower the enrichment. During the process, radioactive fission products whose boiling points are near the proposed 850 degrees C melting temperature can be released. This paper presents a review of fission product release data from uranium-aluminum alloy fuel developed from Severe Accident studies. In addition, scoping calculations using the ORIGEN-S computer code were made to estimate the radioactive inventories in typical research reactor fuel as a function of burnup, initial enrichment, and reactor operating history and shutdown time.Ten elements were identified from the inventory with boiling points below or near the 850 degrees C reference melting temperature. The isotopes 137Cs and 85Kr were considered most important. This review serves as basic data to the design and development of a furnace off-gas system for containment of the volatile species

Inventories and mobilization of unsaturated zone sulfate, fluoride, and chloride related to land use change in semiarid regions, southwestern United States and Australia

Science.gov (United States)

Scanlon, Bridget R.; Stonestrom, David A.; Reedy, Robert C.; Leaney, Fred W.; Gates, John; Cresswell, Richard G.

2009-01-01

Unsaturated zone salt reservoirs are potentially mobilized by increased groundwater recharge as semiarid lands are cultivated. This study explores the amounts of pore water sulfate and fluoride relative to chloride in unsaturated zone profiles, evaluates their sources, estimates mobilization due to past land use change, and assesses the impacts on groundwater quality. Inventories of water‐extractable chloride, sulfate, and fluoride were determined from borehole samples of soils and sediments collected beneath natural ecosystems (N = 4), nonirrigated (“rain‐fed”) croplands (N = 18), and irrigated croplands (N = 6) in the southwestern United States and in the Murray Basin, Australia. Natural ecosystems contain generally large sulfate inventories (7800–120,000 kg/ha) and lower fluoride inventories (630–3900 kg/ha) relative to chloride inventories (6600–41,000 kg/ha). Order‐of‐magnitude higher chloride concentrations in precipitation and generally longer accumulation times result in much larger chloride inventories in the Murray Basin than in the southwestern United States. Atmospheric deposition during the current dry interglacial climatic regime accounts for most of the measured sulfate in both U.S. and Australian regions. Fluoride inventories are greater than can be accounted for by atmospheric deposition in most cases, suggesting that fluoride may accumulate across glacial/interglacial climatic cycles. Chemical modeling indicates that fluorite controls fluoride mobility and suggests that water‐extractable fluoride may include some fluoride from mineral dissolution. Increased groundwater drainage/recharge following land use change readily mobilized chloride. Sulfate displacement fronts matched or lagged chloride fronts by up to 4 m. In contrast, fluoride mobilization was minimal in all regions. Understanding linkages between salt inventories, increased recharge, and groundwater quality is important for quantifying impacts of anthropogenic

Transient fission-product release during reactor shutdown and startup

International Nuclear Information System (INIS)

Hunt, C.E.L.; Lewis, B.J.; Dickson, L.W.

1997-12-01

Sweep-gas experiments performed at AECL's Chalk River Laboratories from 1979 to 1985 have been further analysed to determine the fraction of the gaseous fission-product inventory that is released on reactor shutdown and startup. Empirical equations were derived and applied to calculate the stable xenon release from companion fuel elements and from a well-documented experimental fuel bundle irradiated in the NRU reactor. The calculated gas release could be matched to the measured values within about a factor of two for an experimental irradiation with a burnup of 217 MWh/kgU. There was also limited information on the fraction of the radioactive iodine that was exposed, but not released, on reactor shutdown. An empirical equation is proposed for calculating this fraction. (author)

Bell object relations inventory for adolescents and children: reliability, validity, and factorial invariance.

Science.gov (United States)

Bell, Morris

2003-02-01

The Bell Object Relations Inventory (BORI; Bell,1995) is a self-report instrument that measures deficits in object relations ego functioning. It has demonstrated clinical and research utility in adult populations. This article reports the development of a version of the BORI for children ages 11 to 17, including studies of reliability, validity, and factorial invariance. Data of 705 children from public schools and 110 children from clinics and residential treatments were used. Of the 45 original BORI true/false items, 3 were dropped as inappropriate and most others were rewritten for easier reading. An additional 16 items were created to capture unique features of adolescent experiences in relationships. Items were tested in focus groups and revised accordingly. Eight items were dropped because of low communalities, so that 50 items were included in the final factor analysis. Assessments using self-report items from Behavioral Assessment Scale for Children (BASC; Reynolds & Camphaus, 1992) and the Personality Inventory for Youth (PIY) were also obtained to test concurrent validity. Oblique rotation yielded 5 factors. Four were very similar to the 4 from the adult version and were named accordingly: Alienation, Insecure Attachment, Egocentricity, and Social Incompetence. The fifth scale was comprised mostly of new items and was called Positive Attachment. Scales showed excellent factorial invariance and good internal consistency. Scales generally had very low intercorrelations reflecting their relative independence. Although differences were found for gender and race, the effect sizes were small. Support for construct validity came from moderate correlations with concurrent BASC and PIA scores, analyses of variance showing greater deficits in object relations in pathological subgroups compared with normals, and a trend analysis showed that Alienation scores followed a lawful relationship with increasing severity of psychopathology. These initial findings support

Raw data from the Italian National Forest Inventory are on-line and publicly available

Directory of Open Access Journals (Sweden)

Borghetti M

2016-12-01

Full Text Available Raw data from the Italian National Forest Inventory are on-line and publicly available. The National Forest Service in cooperation with the Forest Monitoring and Management Research Unit of the Council for Agricultural Research and Economics (CREA released the raw data from the National Inventory of Forests and forest Carbon pools - INFC2005 project, the second Italian national forest inventory. Data are available together with metadata information at http://www.inventarioforestale.org/. Users, after registration, can download data from 230.874 living tree stems, 16.472 dead tree stems, 31.083 stumps, from a total of 7.272 field plots (for 1.384 of them additional data on fine woody debris and soil carbon pools are also available.

Feigning combat-related posttraumatic stress disorder on the personality assessment inventory.

Science.gov (United States)

Calhoun, P S; Earnst, K S; Tucker, D D; Kirby, A C; Beckham, J C

2000-10-01

This study examined whether individuals who were instructed on the Diagnostic and Statistical Manual of Mental Disorders (4th ed. [DSM-IV]; American Psychiatric Association, 1994) criteria for posttraumatic stress disorder (PTSD) could feign PTSD on the Personality Assessment Inventory (PAI; Morey, 1991). The study also investigated whether PAI indexes of symptom exaggeration, the Negative Impression Management (NIM) scale and the Malingering index, could identify individuals feigning PTSD. The diagnostic rule for PTSD (Morey, 1991, 1996) was applied to the profiles of a group of 23 veterans with combat-related PTSD and 23 male undergraduates instructed to malinger PTSD. Seventy percent of the student malingerers produced profiles that received diagnostic consideration for PTSD. The NIM cutting score (> or = 8) was highly effective in detecting simulation of PTSD but resulted in the misclassification of a large number of true PTSD cases. There were no significant differences in the overall efficiency of the test with various validity criteria. We discuss the implications of these findings for the use of the PAI in the diagnosis of combat-related PTSD.

Bridging the gap between strategic and management forest inventories

Science.gov (United States)

Ronald E. McRoberts

2009-01-01

Strategic forest inventory programs collect information for a large number of variables on a relatively sparse array of field plots. Data from these inventories are used to produce estimates for large areas such as states and provinces, regions, or countries. The purpose of management forest inventories is to guide management decisions for small areas such as stands....

Canada`s greenhouse gas emissions inventory

Energy Technology Data Exchange (ETDEWEB)

Jaques, A. [Environment Canada, Ottawa, ON (Canada)

1998-09-01

In 1994, Canada was the seventh largest global emitter of CO{sub 2}. The Kyoto Protocol has made it necessary to continue to improve methods for developing emissions inventories. An emissions inventory was defined as `a comprehensive account of air pollutant emissions and associated data from sources within the inventory area over a specified time frame that can be used to determine the effect of emissions on the environment`. The general approach is to compile large-scale emission estimates under averaged conditions for collective sources and sectors, using data that is available on a sectoral, provincial and national basis. Ideally, continuous emission monitors should be used to develop emissions inventories. Other needed improvements include additional research on emissions data, and increased support for international negotiations on reporting policies and related methodologies, verification procedures and adjustments. 1 ref., 5 figs.

Concepts for inventory verification in critical facilities

International Nuclear Information System (INIS)

Cobb, D.D.; Sapir, J.L.; Kern, E.A.; Dietz, R.J.

1978-12-01

Materials measurement and inventory verification concepts for safeguarding large critical facilities are presented. Inspection strategies and methods for applying international safeguards to such facilities are proposed. The conceptual approach to routine inventory verification includes frequent visits to the facility by one inspector, and the use of seals and nondestructive assay (NDA) measurements to verify the portion of the inventory maintained in vault storage. Periodic verification of the reactor inventory is accomplished by sampling and NDA measurement of in-core fuel elements combined with measurements of integral reactivity and related reactor parameters that are sensitive to the total fissile inventory. A combination of statistical sampling and NDA verification with measurements of reactor parameters is more effective than either technique used by itself. Special procedures for assessment and verification for abnormal safeguards conditions are also considered. When the inspection strategies and inventory verification methods are combined with strict containment and surveillance methods, they provide a high degree of assurance that any clandestine attempt to divert a significant quantity of fissile material from a critical facility inventory will be detected. Field testing of specific hardware systems and procedures to determine their sensitivity, reliability, and operational acceptability is recommended. 50 figures, 21 tables

Assessment of radiological releases to the environment from a fusion reactor power plant

International Nuclear Information System (INIS)

Shank, K.E.; Oakes, T.W.; Easterly, C.E.

1978-05-01

This report summarizes the expected tritium and activation-product inventories and presents an assessment of the potential radiological releases from a fusion reactor power plant, hypothetically located at the Oak Ridge National Laboratory. Routine tritium releases and the resulting dose assessment are discussed. Uncertainties associated with the conversion of tritium gas to tritium oxide and the global tritium cycling are evaluated. The difficulties of estimating releases of activated materials and the subsequent dose commitment are reviewed

Determination of accident related release data

International Nuclear Information System (INIS)

Koch, W.; Nolte, O.; Lange, F.; Martens, R.

2004-01-01

For accident safety analyses, for the assessment of potential radiological consequences, for the review of current requirements of the Transport Regulations and for their possible further development as well as for the demonstration that radioactive materials such as LDM candidate material fulfil the regulatory requirements reliable release data following mechanical impact are required. This is definitely one of the demanding issues in the field of transport safety of radioactive materials. In this context special attention has to be paid to radioactive wastes immobilised in brittle materials, e.g. cement/concrete, glass, ceramics or other brittle materials such as fresh and spent fuel. In this presentation we report on a long-term experimental program aiming at improving the general physical understanding of the release process as well as the quantity and the quality of release data. By combining laboratory experiments using small scale test specimens with a few key scaling experiments with large scale test objects significant progress was achieved to meet this objective. The laboratory equipment enables the in-situ determination of the amount and aerodynamic size distribution of the airborne particles generated upon impact of the test specimen on a hard target. Impact energies cover the range experienced in transport accidents including aircraft accidents. The well defined experimental boundary conditions and the good reproducibility of the experimental procedure allowed for systematic studies to exactly measure the amount and aerodynamic size distribution of the airborne release and to quantify its dependence on relevant parameters such as energy input, material properties, and specimen geometry. The experimental program was performed within the scope of various national and international (e.g. EU-funded) projects. The small scale experiments with brittle materials revealed a pronounced universality of the airborne release in view of the material properties and

Oil inventories should be based on margins, supply reliability

International Nuclear Information System (INIS)

Waguespack, K.; Cantor, B.D.

1996-01-01

US oil inventories have plummeted to their lowest recorded levels this year, leading industry observers to conclude that refiners have adopted new just-in-time (JIT) inventory policies. Total crude oil inventories are about 300 million bbl -- 8% below the 10-year average. Distillate inventories posted similar declines this year because of unusually cold winter temperatures and refiners' reluctance to build sufficient stocks in the autumn months. Gasoline stocks are 20% below the 10-year average at 200 million bbl, despite forecasts of record-high gasoline demand this summer. The sudden drop in crude and product inventories this year is widely considered a sign that refiners have implemented JIT, signaling a permanent shift to reduced stocks. The authors submit that the shift towards reduced oil inventories is not related to a concerted adoption of JIT by US refiners, and that oil inventory management decisions should instead be based on refining margins and supply reliability. The paper discusses the JIT revolution and the optimal-inventory model

Dual-release hydrocortisone treatment: glycometabolic profile and health-related quality of life

Directory of Open Access Journals (Sweden)

L M Mongioì

2018-01-01

Full Text Available Objective: Adrenal insufficiency (AI is a chronic condition associated with increased mortality and morbidity. The treatment of AI in the last years has been object of important changes due to the development of a dual-release preparation of hydrocortisone. It differs from previous therapeutic strategy as it contemplates a once-daily tablet that allows more closely mimicking the physiological circadian cortisol rhythm. The aim of the study was to evaluate the effects of dual-release hydrocortisone treatment on the glycometabolic profile and health-related quality of life of patients with AI. Design and Methods: In this clinical open trial, we enrolled ten patients with primary AI (41 ± 2.67 years and nine patients with AI secondary to hypopituitarism (53.2 ± 17.7 years. We evaluated the glycometabolic profile before and 3, 6, 9 and 12 months after dual-release hydrocortisone administration. We also evaluated health-related quality of life, estimated by the AddiQol questionnaire. The mean dose administered of dual-release hydrocortisone was 28.33 ± 6.68 mg/day. Results: One female hypopituitary patient dropped out from the study. After 12 months of treatment, the mean dosage administered of dual-release hydrocortisone was significantly lower (P < 0.05 and all patients reported improved quality of life and well-being. The glycometabolic profile improved and the glycosylated hemoglobin decreased significantly in patients with primary AI (6.25 ± 0.2 vs 5.35 ± 0.17, P < 0.05. In contrast, hypopituitary patients had worse glycometabolic profile and a trend toward hypertriglyceridemia. Conclusions: Dual-release hydrocortisone treatment improved the quality of life of patients with AI, and it allowed a decrease of cortisol dosage administered in the absence of side effects. The glycometabolic profile worsened in hypopituitary patients.

Inventory of Federal energy-related environment and safety research for FY 1977. Volume IV. Indices

Energy Technology Data Exchange (ETDEWEB)

1978-07-01

This volume contains indexes useful for accessing projects contained in the FY 1977 Federal Inventory. The indexing has been greatly broadened this year to provide hard copy users with greater flexibility in locating projects. The Inventory projects are printed sequentially by log number. An inventory log number is a unique number assigned to each project from a block of numbers set aside for each agency. The association of agencies with blocks of log numbers is found in the table of contents of the Index (Volume III).

Forest inventory in Myanmar

Energy Technology Data Exchange (ETDEWEB)

Bo, Sit [Forest Resource Div., Forest Department (Myanmar)

1993-10-01

Forest inventory in Myanmar started in 1850s. Up till 1975, Myanmar Forest Department conducted forest inventories covering approximately one forest division every year. The National Forest Survey and Inventory Project funded by UNDP and assisted by FAO commenced in 1981 and the National Forest Management and Inventory project followed in 1986. Up till end March 1993, pre-investment inventory has covered 26.7 million acres, reconnaissance inventory 5.4 million acres and management inventory has carried out in 12 townships

Forest inventory in Myanmar

International Nuclear Information System (INIS)

Sit Bo

1993-01-01

Forest inventory in Myanmar started in 1850s. Up till 1975, Myanmar Forest Department conducted forest inventories covering approximately one forest division every year. The National Forest Survey and Inventory Project funded by UNDP and assisted by FAO commenced in 1981 and the National Forest Management and Inventory project followed in 1986. Up till end March 1993, pre-investment inventory has covered 26.7 million acres, reconnaissance inventory 5.4 million acres and management inventory has carried out in 12 townships

Accounting concept of inventories in postindustrial economy

Directory of Open Access Journals (Sweden)

Pravdyuk N.L.

2017-06-01

Full Text Available The accounting of inventories has undergone significant changes over a relatively short period of time. It has changed the scientific picture of their definition and classification, measurement and write-offs reflected in the financial statements. However, these changes happen without proper interpretation and system analysis. And, at least in general terms the inventories are conducted in Ukraine according to IFRS; this causes some obstacles to the objective reflection of working capital of enterprises, and the transparency of disclosure and is not conducive to the formation of a proper investment climate. It is established that the information provision inventory control must meet the requirements of the postindustrial economy by the complicating and deepening the complexity of accounting, the introduction of new forms and their synthesis with the current one, a gradual reorganization to ensure the needs of consumers and enterprise evaluation. The results of the study have substantiated the fundamentals of accounting concepts in the postindustrial economy in the part of the circulating capital, which forms inventories. The information support of inventory management should be implemented in a hierarchical way, when it first and foremost analyzes the working capital, and further deals with inventories and stocks as its subordinate components. The author considers the material goods to be a broader concept than reserves, because they have a dual nature both estimated as the share of negotiable assets, and as the physical component of material costs. The paper gives the definition of this category of symbiosis, which is based on P(CBU 9. The general structure of the current inventories are of significant importance, which has differences in industries, the dominant of which is agriculture, industry, construction, trade, material production. The postindustrial economy caused the questions of differentiation of concepts "production" and "material

The impact of turn around time in Brazilian Navy inventories

OpenAIRE

Casagrande, Mauricio

2000-01-01

Approved for public release; distribution is unlimited. This thesis analyzes how the operation of helicopters produced and supported by manufacturers in various countries affect Brazilian Navy repairable inventories levels and costs. The research is based on a scenario where the Brazilian Navy operates 68 helicopters, manufactured by contractors in USA, France, England and Italy, and the Brazilian Navy relies on these manufacturers for depot-level maintenance. We develop a simulation model...

An inventory of wetlands in the East Fork Poplar Creek floodplain, Anderson and Roane Counties, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-12-01

An inventory of wetlands within the floodplain of East Fork Poplar Creek (EFPC) in Anderson and Roane Counties, Tennessee was conducted during October, 1991 through May, 1992 for the US Department of Energy (DOE) by the US Army Corps of Engineers, Nashville District. About 15 miles of EFPC channel and 500 acres of its floodplain are contaminated with mercury and other contaminants released from the Y-12 Plant on the DOE Oak Ridge Reservation. The wetland inventory will serve as baseline information for DOE`s remedial action planning and National Environmental Policy Act compliance efforts related to the contamination. In order to provide broad wetland determinations beyond which future wetland definitions are unlikely to expand, the 1989 Federal Manual for Identifying And Delineating Jurisdictional Wetlands was utilized. Using the manual`s methodology in a contaminated system under the approved health and safety plan presented some unique problems, resulting in intrusive sampling for field indicators of hydric soils being accomplished separately from observation of other criteria. Beginning with wetland areas identified on National Wetland Inventory Maps, the entire floodplain was examined for presence of wetland criteria, and 17 wetlands were identified ranging from 0.01 to 2.81 acres in size. The majority of wetlands identified were sized under 1 acre. Some of the wetlands identified were not delineated on the National Wetland Inventory Maps, and much of the wetland area delineated on the maps did not meet the criteria under the 1989 manual.

Interactive Inventory Monitoring

Science.gov (United States)

Garud, Sumedha

2013-01-01

Method and system for monitoring present location and/or present status of a target inventory item, where the inventory items are located on one or more inventory shelves or other inventory receptacles that communicate with an inventory base station through use of responders such as RFIDs. A user operates a hand held interrogation and display (lAD) module that communicates with, or is part of the base station to provide an initial inquiry. lnformation on location(s) of the larget invenlory item is also indicated visibly and/or audibly on the receptacle(s) for the user. Status information includes an assessment of operation readiness and a time, if known, that the specified inventory item or class was last removed or examined or modified. Presentation of a user access level may be required for access to the target inventgory item. Another embodiment provides inventory informatin for a stack as a sight-impaired or hearing-impaired person adjacent to that stack.

Measurements of instant-release source terms for 137Cs, 90Sr, 99Tc, 129I and 14C in used CANDU fuels

International Nuclear Information System (INIS)

Stroes-Gascoyne, S.

1996-01-01

Combined gap and grain-boundary inventories of 137 Cs, 129 I, 90 Sr, 99 Tc and 14 C were measured in 15 used CANDU fuel elements by leaching crushed fuel samples. A good correlation between the combined gap and grain-boundary inventories of 137 Cs and 129 I was found, suggesting that these fission products exhibit similar behavior in CANDU fuel. The expected correlation between combined gap and grain-boundary inventories of 137 Cs and 129 I with calculated fission-gas release to the gap and grain boundaries could only be confirmed for lower power fuels ( 90 Sr were higher than expected and showed no correlation with calculated fission-gas release. No values for the combined gap and grain-boundary inventories of 99 Tc were obtained because 99 Tc in used fuel samples is very insoluble and appears to require oxidation prior to dissolution. Combined gap and grain-boundary inventories of 14 C appeared to be independent of fuel power or burnup. (orig.)

Tritium recovery from fusion blankets using solid lithium compounds. I. Design and minimization of tritium inventory

International Nuclear Information System (INIS)

Powell, J.R.

1975-01-01

Tritium blanket inventories of 100 curies/MW(e) are readily achievable, and inventories as low as 10 curies/MW(e) are possible for blankets with small lithium compound particulates (less than or equal to 50μ) at T greater than or equal to 800 0 C. Of the three release modes [A - to the main coolant (e.g., He) stream; B - to a separate processing circuit; and C - to the plasma region], mode A appears optimum for blankets using gas-cooled metallic structures (e.g., Al, stainless), while mode C appears optimum for high temperature refractory (e.g., C, SiC) structures. The greater structural complexity of mode B makes it less attractive than modes A and C. No recovery method is required for mode C release. With mode A release, tritium inventory in the coolant circuits ranges from 1 to 10 curies/MW(e), depending on processing parameters. Tritium leak rates to the environment during normal operation can be kept to less than or equal to 10 -3 curies/MW(e) per day with low permeability barriers. In general, a mixture of T 2 and T 2 O is present in the coolant stream. Three methods of tritium recovery are examined: (1) Conversion to T 2 followed by absorption in a metal hydride bed. (2) Conversion to T 2 followed by condensation at approximately 6 0 K. (3) Conversion to T 2 O followed by condensation at approximately 100 0 K

Information related to low-level mixed waste inventory, characteristics, generation, and facility assessment for treatment, storage, and disposal alternatives considered in the U.S. Department of Energy Waste Management Programmatic Environmental Impact Statement

International Nuclear Information System (INIS)

Wilkins, B.D.; Dolak, D.A.; Wang, Y.Y.; Meshkov, N.K.

1996-12-01

This report was prepared to support the analysis of risks and costs associated with the proposed treatment of low-level mixed waste (LLMW) under management of the US Department of Energy (DOE). The various waste management alternatives for treatment of LLMW have been defined in the DOE's Office of Waste Management Programmatic Environmental Impact Statement. This technical memorandum estimates the waste material throughput expected at each proposed LLMW treatment facility and analyzes potential radiological and chemical releases at each DOE site resulting from treatment of these wastes. Models have been developed to generate site-dependent radiological profiles and waste-stream-dependent chemical profiles for these wastes. Current site-dependent inventories and estimates for future generation of LLMW have been obtained from DOE's 1994 Mixed Waste Inventory Report (MWIR-2). Using treatment procedures developed by the Mixed Waste Treatment Project, the MWIR-2 database was analyzed to provide waste throughput and emission estimates for each of the different waste types assessed in this report. Uncertainties in the estimates at each site are discussed for waste material throughputs and radiological and chemical releases

Information related to low-level mixed waste inventory, characteristics, generation, and facility assessment for treatment, storage, and disposal alternatives considered in the U.S. Department of Energy Waste Management programmatic environmental impact statement

International Nuclear Information System (INIS)

Wilkins, B.D.; Dolak, D.A.; Wang, Y.Y.; Meshkov, N.K.

1995-04-01

This report was prepared to support the analysis of risks and costs associated with the proposed treatment of low-level mixed waste (LLMW) under management of the U.S. Department of Energy (DOE). The various waste management alternatives for treatment of LLMW have been defined in the DOE's Office of Waste Management Programmatic Environmental Impact Statement. This technical memorandum estimates the waste material throughput expected at each proposed LLMW treatment facility and analyzes potential radiological and chemical releases at each DOE site resulting from treatment of these wastes. Models have been developed to generate site-dependent radiological profiles and waste-stream-dependent chemical profiles for these wastes. Current site-dependent inventories and estimates for future generation of LLMW have been obtained from DOE's 1994 Mixed Waste Inventory Report (MWIR-2). Using treatment procedures developed by the Mixed Waste Treatment Project, the MWIR-2 database was analyzed to provide waste throughput and emission estimates for each of the different waste types assessed in this report. Uncertainties in the estimates at each site are discussed for waste material throughputs and radiological and chemical releases

Denmark's National Inventory Report 2015 and 2016

DEFF Research Database (Denmark)

Nielsen, Ole-Kenneth; Plejdrup, Marlene Schmidt; Winther, Morten

This report is Denmark’s annual documentation report of the greenhouse gas inventory submitted to the United Nations Framework Convention on Climate Change (UNFCCC) and the Kyoto Protocol. The report is prepared in accordance with the UNFCCC reporting guidelines and CMP decisions and contains all...... the mandatory information related to the Danish greenhouse gas inventory. The report contains information on emissions of CO2, CH4, N2O, HFCs, PFCs and SF6 and removals of CO2. The report describes among other aspects the data underpinning the inventory, the methodologies to estimate emissions....../removals and the quality control procedures in place. The main sectoral chapters of the report refer to Denmark, while information on the emission inventory of Greenland and the Faroe Islands is included in Chapter 16 and Annex 7, respectively....

Design considerations for tropical forest inventories

Directory of Open Access Journals (Sweden)

Ronald Edward McRoberts

2013-06-01

Full Text Available Forests contribute substantially to maintaining the global greenhouse gas balance, primarily because among the five economic sectors identified by the United Nations Framework Convention on Climate Change, only the forestry sector has the potential to remove greenhouse gas emissions from the atmosphere. In this context, development of national forest carbon accounting systems, particularly in countries with tropical forests, has emerged as an international priority. Because these systems are often developed as components of or in parallel with national forest inventories, a brief review of statistical issues related to the development of forest ground sampling designs is provided. This overview addresses not only the primary issues of plot configurations and sampling designs, but also to a lesser extent the emerging roles of remote sensing and uncertainty assessment. Basic inventory principles are illustrated for two case studies, the national forest inventory of Brazil with special emphasis on the state of Santa Catarina, and an inventory for Tanzania.

Inventory and source term evaluation of Russian nuclear power plants for marine applications

International Nuclear Information System (INIS)

Reistad, O.; Oelgaard, P.L.

2006-04-01

This report discusses inventory and source term properties in regard to operation and possible releases due to accidents from Russian marine reactor systems. The first part of the report discusses relevant accidents on the basis of both Russian and western sources. The overview shows that certain vessels were much more accident prone compared to others, in addition, there have been a noteworthy reduction in accidents the last two decades. However, during the last years new types of incidents, such as collisions, has occurred more frequently. The second part of the study considers in detail the most important factors for the source term; reactor operational characteristics and the radionuclide inventory. While Russian icebreakers has been operated on a similar basis as commercial power plants, the submarines has different power cyclograms which results in considerable lower values for fission product inventory. Theoretical values for radionuclide inventory are compared with computed results using the modelling tool HELIOS. Regarding inventory of transuranic elements, the results of the calculations are discussed in detail for selected vessels. Criticality accidents, loss-of-cooling accidents and sinking accidents are considered, bases on actual experiences with these types of accident and on theoretical considerations, and source terms for these accidents are discussed in the last chapter. (au)

Inventory and source term evaluation of Russian nuclear power plants for marine applications

Energy Technology Data Exchange (ETDEWEB)

Reistad, O. [Norwegian Radiation Protection Authority (Norway); Oelgaard, P.L. [Risoe National Lab. (Denmark)

2006-04-15

This report discusses inventory and source term properties in regard to operation and possible releases due to accidents from Russian marine reactor systems. The first part of the report discusses relevant accidents on the basis of both Russian and western sources. The overview shows that certain vessels were much more accident prone compared to others, in addition, there have been a noteworthy reduction in accidents the last two decades. However, during the last years new types of incidents, such as collisions, has occurred more frequently. The second part of the study considers in detail the most important factors for the source term; reactor operational characteristics and the radionuclide inventory. While Russian icebreakers has been operated on a similar basis as commercial power plants, the submarines has different power cyclograms which results in considerable lower values for fission product inventory. Theoretical values for radionuclide inventory are compared with computed results using the modelling tool HELIOS. Regarding inventory of transuranic elements, the results of the calculations are discussed in detail for selected vessels. Criticality accidents, loss-of-cooling accidents and sinking accidents are considered, bases on actual experiences with these types of accident and on theoretical considerations, and source terms for these accidents are discussed in the last chapter. (au)

Maladaptive Personality Trait Models: Validating the Five-Factor Model Maladaptive Trait Measures With the Personality Inventory for DSM-5 and NEO Personality Inventory.

Science.gov (United States)

Helle, Ashley C; Mullins-Sweatt, Stephanie N

2017-05-01

Eight measures have been developed to assess maladaptive variants of the five-factor model (FFM) facets specific to personality disorders (e.g., Five-Factor Borderline Inventory [FFBI]). These measures can be used in their entirety or as facet-based scales (e.g., FFBI Affective Dysregulation) to improve the comprehensiveness of assessment of pathological personality. There are a limited number of studies examining these scales with other measures of similar traits (e.g., DSM-5 alternative model). The current study examined the FFM maladaptive scales in relation to the respective general personality traits of the NEO Personality Inventory-Revised and the pathological personality traits of the DSM-5 alternative model using the Personality Inventory for DSM-5. The results indicated the FFM maladaptive trait scales predominantly converged with corresponding NEO Personality Inventory-Revised, and Personality Inventory for DSM-5 traits, providing further validity for these measures as extensions of general personality traits and evidence for their relation to the pathological trait model. Benefits and applications of the FFM maladaptive scales in clinical and research settings are discussed.

Potential Causes of Significant Inventory Differences at Bulk Handling Facilities and the Importance of Inventory Difference Action Levels

International Nuclear Information System (INIS)

Homer, Alan; O’Hagan, Brendan

2015-01-01

Accountancy for nuclear material can be split into two categories. Firstly, where possible, accountancy should be in terms of items that can be transferred as discrete packages and their contents fixed at the time of their creation. All items must remain accounted for at all times, and a single missing item is considered significant. Secondly, where nuclear material is unconstrained, for example in a reprocessing plant where it can change form, there is an uncertainty that relates to the amount of material present in any location. Cumulatively, these uncertainties can be summed and provide a context for any estimate of material in a process. Any apparent loss or gain between what has been physically measured within a facility during its physical inventory take and what is reported within its nuclear material accounts is known as an inventory difference. The cumulative measurement uncertainties can be used to set an action level for the inventory difference so that if an inventory difference is observed outside of such action levels, the difference is classified as significant and an investigation to find the root cause(s) is required. The purpose of this paper is to explore the potential causes of significant inventory differences and to provide a framework within which an inventory difference investigation can be carried out.

Pollutant Release and Transfer Register

International Nuclear Information System (INIS)

2008-01-01

Since 1974 a number of organisations have been working closely together in this pollutant register (PRTR) project to collect and formally establish the yearly releases of pollutants to air, water and soil in the Netherlands. Results of this project serve to underpin the national environmental policy. Data is in this way also provided for the many environmental reports to international organisations such as the European Union and the United Nations, e.g. the National Inventory Report for the Kyoto Protocol. This website shows the yearly releases (emissions) of the most important pollutants in the Netherlands. You can explore the emission data through various channels, such as maps, graphs and tables. But you can also download all the details into your own database. The data shown in this website is updated 2 to 3 times a year. The current release shows emissions for 1990, 1995, 2000, 2004, 2005 and 2006 The 2006 emissions are preliminary data and not yet shown in the maps. We expect to add an extra year in August 2008 [nl

Sensitivity of the global submarine hydrate inventory to scenarios of future climate change

Science.gov (United States)

Hunter, S. J.; Goldobin, D. S.; Haywood, A. M.; Ridgwell, A.; Rees, J. G.

2013-04-01

The global submarine inventory of methane hydrate is thought to be considerable. The stability of marine hydrates is sensitive to changes in temperature and pressure and once destabilised, hydrates release methane into sediments and ocean and potentially into the atmosphere, creating a positive feedback with climate change. Here we present results from a multi-model study investigating how the methane hydrate inventory dynamically responds to different scenarios of future climate and sea level change. The results indicate that a warming-induced reduction is dominant even when assuming rather extreme rates of sea level rise (up to 20 mm yr-1) under moderate warming scenarios (RCP 4.5). Over the next century modelled hydrate dissociation is focussed in the top ˜100m of Arctic and Subarctic sediments beneath business-as-usual scenario (RCP 8.5), upper estimates of resulting global sea-floor methane fluxes could exceed estimates of natural global fluxes by 2100 (>30-50TgCH4yr-1), although subsequent oxidation in the water column could reduce peak atmospheric release rates to 0.75-1.4 Tg CH4 yr-1.

TMAP-7 simulation of D2 thermal release data from Be co-deposited layers

International Nuclear Information System (INIS)

Baldwin, M.J.; Schwarz-Selinger, T.; Yu, J.H.; Doerner, R.P.

2013-01-01

The efficacy of (1) bake-out at 513 K and 623 K, and (2) thermal transient (10 ms) loading to up to 1000 K, is explored for reducing D inventory in 1 μm thick Be–D (D/Be ∼0.1) co-deposited layers formed at 323 K for experiment (1) and ∼500 K for experiment (2). D release data from co-deposits are obtained by thermal desorption and used to validate a model input into the Tritium Migration and Analysis Program 7 (TMAP). In (1), good agreement with experiment is found for a TMAP model encorporating traps of activation energies, 0.80 eV and 0.98 eV, whereas an additional 2 eV trap was required to model experiment (2). Thermal release is found to be trap limited, but simulations are optimal when surface recombination is taken into account. Results suggest that thick built-up co-deposited layers will hinder ITER inventory control, and that bake periods (∼1 day) will be more effective in inventory reduction than transient thermal loading

TMAP-7 simulation of D2 thermal release data from Be co-deposited layers

Science.gov (United States)

Baldwin, M. J.; Schwarz-Selinger, T.; Yu, J. H.; Doerner, R. P.

2013-07-01

The efficacy of (1) bake-out at 513 K and 623 K, and (2) thermal transient (10 ms) loading to up to 1000 K, is explored for reducing D inventory in 1 μm thick Be-D (D/Be ˜0.1) co-deposited layers formed at 323 K for experiment (1) and ˜500 K for experiment (2). D release data from co-deposits are obtained by thermal desorption and used to validate a model input into the Tritium Migration & Analysis Program 7 (TMAP). In (1), good agreement with experiment is found for a TMAP model encorporating traps of activation energies, 0.80 eV and 0.98 eV, whereas an additional 2 eV trap was required to model experiment (2). Thermal release is found to be trap limited, but simulations are optimal when surface recombination is taken into account. Results suggest that thick built-up co-deposited layers will hinder ITER inventory control, and that bake periods (˜1 day) will be more effective in inventory reduction than transient thermal loading.

Low and intermediate level waste in SFR-1. Reference Waste Inventory 2007

International Nuclear Information System (INIS)

Almkvist, Lisa; Gordon, Ann

2007-11-01

The objective with this report is to describe all the waste and the waste package that is expected to be deposited in SFR 1 at the time of closure. The report will form the basis for the release calculation in the safety analysis for SFR 1. Three different scenarios are explored in this report; the waste inventory is based on an estimated operational lifetime of the Swedish nuclear power plants of 50 and 60 years and that closure of the SFR 1 repository will take place in 2040 or 2050 respectively. The third scenario is where the repository is full (one part where the activity adds up to 1016 Bq and one part where the repository is considered full regarding volume). In the report, data about geometries, weights, materials, chemicals and radionuclide are given. No chemotoxic material has been identified in the waste. The inventory is estimated using the Prosit-interface which extracts information from the Triumf database. The inventory is based on so called 'waste types' and the waste types' 'reference waste package'. The reference waste package combined with a prognosis of the number of waste packages to be delivered to SFR 1 gives the final waste inventory for SFR 1. All reference waste packages are thoroughly described in the appendices of this report. The reference waste packages are as far as possible based on actual experiences and measurements. The radionuclide inventory is also based on actual measurements. The inventory is based on measurements of 60 Co and 137 Cs in waste packages and on measurements of 239 Pu and 240 Pu in reactor water. Other nuclides in the inventory are calculated with correlation factors

The influence of source term release parameters on health effects

International Nuclear Information System (INIS)

Jeong, Jong Tae; Ha, Jae Joo

1998-08-01

In this study, the influence of source term release parameters on the health effects was examined. This is very useful in identifying the relative importance of release parameters and can be an important factor in developing a strategy for reducing offsite risks. The release parameters investigated in this study are release height, heat content, fuel burnup, release time, release duration, and warning time. The health effects affected by the change of release parameters are early fatalities, cancer fatalities, early injuries, cancer injuries, early fatality risk, population weighted early fatality risk, population weighted cancer fatality risk, effective whole body population dose, population exceeding an early acute red bone marrow dose of 1.5 Sv, and distance at which early fatalities are expected to occur. As release height increases, the values of early health effects such as early fatalities and injuries decrease. However, the release height dose not have significant influences on late health effects. The values of both early and late health effects decrease as heat content increases. The increase fuel burnup, i.e., the increase of core inventories increases the late health effects, however, has small influence on the early health effects. But, the number of early injuries increases as the fuel burnup increases. The effects of release time increase shows very similar influence on both the early and late health effects. As the release time increases to 2 hours, the values of health effects increase and then decrease rapidly. As release duration increases, the values of late health effects increase slightly, however, the values of early health effects decrease. As warning time increases to 2 hours, the values of late health effects decrease and then shows no variation. The number of early injuries decreases rapidly as the warning time increases to 2 hours. However, the number of early fatalities and the early fatality risk increase as the warning time increases

Wildlife habitat, range, recreation, hydrology, and related research using Forest Inventory and Analysis surveys: a 12-year compendium

Science.gov (United States)

Victor A. Rudis

1991-01-01

More than 400 publications are listed for the period 1979 to 1990; these focus on water, range, wildlife habitat, recreation, and related studies derived from U.S. Department of Agriculture, forest Service, Forest Inventory and Analysis unit surveys conducted on private and public land in the continental United States. Included is an overview of problems and progress...

A systems approach to inventory management of repairables in the Navy

OpenAIRE

Apple, Chris Leon

1985-01-01

Approved for public release; distribution is unlimited This thesis develops an inventory model for repairable items which integrates the shipboard protection level into the wholesale stock level computations. It uses mean supply response time (MSRT) as its measure of effectiveness and provides methods for computing either the required wholesale stock level given a MSRT goal or for minimizing the system MSRT subject to budgetary constraints. Examples are provided which demons...

Forecasting short-run crude oil price using high- and low-inventory variables

International Nuclear Information System (INIS)

Ye, Michael; Zyren, John; Shore, Joanne

2006-01-01

Since inventories have a lower bound or a minimum operating level, economic literature suggests a nonlinear relationship between inventory level and commodity prices. This was found to be the case in the short-run crude oil market. In order to explore this inventory-price relationship, two nonlinear inventory variables are defined and derived from the monthly normal level and relative level of OECD crude oil inventories from post 1991 Gulf War to October 2003: one for the low inventory state and another for the high inventory state of the crude oil market. Incorporation of low- and high-inventory variables in a single equation model to forecast short-run WTI crude oil prices enhances the model fit and forecast ability

Generation and release of radioactive gases in LLW disposal facilities

Energy Technology Data Exchange (ETDEWEB)

Yim, M.S. [Harvard School Public Health, Boston, MA (United States); Simonson, S.A. [Massachusetts Institute of Technology, Cambridge, MA (United States)

1995-02-01

The atmospheric release of radioactive gases from a generic engineered LLW disposal facility and its radiological impacts were examined. To quantify the generation of radioactive gases, detailed characterization of source inventory for carbon-14, tritium, iodine-129, krypton-85, and radon-222, was performed in terms of their activity concentrations; their distribution within different waste classes, waste forms and containers; and their subsequent availability for release in volatile or gaseous form. The generation of gases was investigated for the processes of microbial activity, radiolysis, and corrosion of waste containers and metallic components in wastes. The release of radionuclides within these gases to the atmosphere was analyzed under the influence of atmospheric pressure changes.

Nuclear, thermo-mechanical and tritium release analysis of ITER breeding blanket

International Nuclear Information System (INIS)

Kosaku, Yasuo; Kuroda, Toshimasa; Enoeda, Mikio; Hatano, Toshihisa; Sato, Satoshi; Miki, Nobuharu; Akiba, Masato

2003-06-01

The design of the breeding blanket in ITER applies pebble bed breeder in tube (BIT) surrounded by multiplier pebble bed. It is assumed to use the same module support mechanism and coolant manifolds and coolant system as the shielding blankets. This work focuses on the verification of the design of the breeding blanket, from the viewpoints which is especially unique to the pebble bed type breeding blanket, such as, tritium breeding performance, tritium inventory and release behavior and thermo-mechanical performance of the ITER breeding blanket. With respect to the neutronics analysis, the detailed analyses of the distribution of the nuclear heating rate and TBR have been performed in 2D model using MCNP to clarify the input data for the tritium inventory and release rate analyses and thermo-mechanical analyses. With respect to the tritium inventory and release behavior analysis, the parametric analyses for selection of purge gas flow rate were carried out from the view point of pressure drop and the tritium inventory/release performance for Li 2 TiO 3 breeder. The analysis result concluded that purge gas flow rate can be set to conventional flow rate setting (88 l/min per module) to 1/10 of that to save the purge gas flow and minimize the size of purge gas pipe. However, it is necessary to note that more tritium is transformed to HTO (chemical form of water) in case of Li 2 TiO 3 compared to other breeder materials. With respect to the thermo-mechanical analyses of the pebble bed blanket structure, the analyses have been performed by ABAQUS with 2D model derived from one of eight facets of a blanket module, based on the reference design. Analyses were performed to identify the temperature distribution incorporating the pebble bed mechanical simulation and influence of mechanical behavior to the thermal behavior. The result showed that the maximum temperature in the breeding material was 617degC in the first row of breeding rods and the minimum temperature was 328

The needs of the relatives in the adult intensive care unit: Cultural adaptation and psychometric properties of the Chilean-Spanish version of the Critical Care Family Needs Inventory.

Science.gov (United States)

Rojas Silva, Noelia; Padilla Fortunatti, Cristobal; Molina Muñoz, Yerko; Amthauer Rojas, Macarena

2017-12-01

The admission of a patient to an intensive care unit is an extraordinary event for their family. Although the Critical Care Family Needs Inventory is the most commonly used questionnaire for understanding the needs of relatives of critically ill patients, no Spanish-language version is available. The aim of this study was to culturally adapt and validate theCritical Care Family Needs Inventory in a sample of Chilean relatives of intensive care patients. The back-translated version of the inventory was culturally adapted following input from 12 intensive care and family experts. Then, it was evaluated by 10 relatives of recently transferred ICU patients and pre-tested in 10 relatives of patients that were in the intensive care unit. Psychometric properties were assessed through exploratory factor analysis and Cronbach's α in a sample of 251 relatives of critically ill patients. The Chilean-Spanish version of the Critical Care Family Needs Inventoryhad minimal semantic modifications and no items were deleted. A two factor solution explained the 31% of the total instrument variance. Reliability of the scale was good (α=0.93), as were both factors (α=0.87; α=0.93). The Chilean-Spanish version of theCritical Care Family Needs Inventory was found valid and reliable for understanding the needs of relatives of patients in acute care settings. Copyright © 2017 Elsevier Ltd. All rights reserved.

TMAP-7 simulation of D{sub 2} thermal release data from Be co-deposited layers

Energy Technology Data Exchange (ETDEWEB)

Baldwin, M.J., E-mail: mbaldwin@ferp.ucsd.edu [Center for Energy Research, University of California at San Diego, La Jolla, CA 92093-0417 (United States); Schwarz-Selinger, T. [Max-Planck-Institut für Plasmaphysik, EURATOM Association, Boltzmannstrasse 2, 85748 Garching (Germany); Yu, J.H. [Center for Energy Research, University of California at San Diego, La Jolla, CA 92093-0417 (United States); Doerner, R.P., E-mail: rdoerner@ucsd.edu [Center for Energy Research, University of California at San Diego, La Jolla, CA 92093-0417 (United States)

2013-07-15

The efficacy of (1) bake-out at 513 K and 623 K, and (2) thermal transient (10 ms) loading to up to 1000 K, is explored for reducing D inventory in 1 μm thick Be–D (D/Be ∼0.1) co-deposited layers formed at 323 K for experiment (1) and ∼500 K for experiment (2). D release data from co-deposits are obtained by thermal desorption and used to validate a model input into the Tritium Migration and Analysis Program 7 (TMAP). In (1), good agreement with experiment is found for a TMAP model encorporating traps of activation energies, 0.80 eV and 0.98 eV, whereas an additional 2 eV trap was required to model experiment (2). Thermal release is found to be trap limited, but simulations are optimal when surface recombination is taken into account. Results suggest that thick built-up co-deposited layers will hinder ITER inventory control, and that bake periods (∼1 day) will be more effective in inventory reduction than transient thermal loading.

Safety analysis and inventory control of transuranic and low-level waste in common storage

International Nuclear Information System (INIS)

Porten, D.R.; Bonner, A.L.; Joyce, J.P.

1993-01-01

This paper describes a methodology developed For the inventory control of low-level waste (LLW) and transuranic (TRU) waste, when both are stored in the same location, and both contribute to an inventory constrained by safety considerations. Development of the method arose from the necessity to make safety analysis calculations for the addition of LLW, in quantities greater than existing inventory limits would allow when stored with TRU waste, in the Hanford Central Waste Complex (CWC)-Ensuring that the dose consequences of credible releases are maintained at low-hazard limits or less, was used to allow greater than Type A quantities of LLW into the CWC. Basically, what happens is the original limited amount of TRU allowed is reduced by some equivalent amount of LLW introduced. The total quantity of TRU, and LLW in excess of Type A quantities, must be administratively maintained via curie equivalency Factors to ensure operation as a low-hazard Facility. The ''equivalency'' between TRU and LLW proposed here is specific only to the CWC, but the methodology can be used for other specific applications, such as TRU and LLW storage or handling facilities where inventory limits must be enforced or where a simplified inventory system is required

Low and intermediate level waste in SFR-1. Reference Waste Inventory 2007

Energy Technology Data Exchange (ETDEWEB)

Almkvist, Lisa (Vattenfall Power Consultant AB, Stockholm (SE)); Gordon, Anna (Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE))

2007-11-15

The objective with this report is to describe all the waste and the waste package that is expected to be deposited in SFR 1 at the time of closure. The report will form the basis for the release calculation in the safety analysis for SFR 1. Three different scenarios are explored in this report; the waste inventory is based on an estimated operational lifetime of the Swedish nuclear power plants of 50 and 60 years and that closure of the SFR 1 repository will take place in 2040 or 2050 respectively. The third scenario is where the repository is full (one part where the activity adds up to 1016 Bq and one part where the repository is considered full regarding volume). In the report, data about geometries, weights, materials, chemicals and radionuclide are given. No chemotoxic material has been identified in the waste. The inventory is estimated using the Prosit-interface which extracts information from the Triumf database. The inventory is based on so called 'waste types' and the waste types' 'reference waste package'. The reference waste package combined with a prognosis of the number of waste packages to be delivered to SFR 1 gives the final waste inventory for SFR 1. All reference waste packages are thoroughly described in the appendices of this report. The reference waste packages are as far as possible based on actual experiences and measurements. The radionuclide inventory is also based on actual measurements. The inventory is based on measurements of 60Co and 137Cs in waste packages and on measurements of 239Pu and 240Pu in reactor water. Other nuclides in the inventory are calculated with correlation factors

Procedure for taking physical inventories

International Nuclear Information System (INIS)

Anon.

1981-01-01

This session is intended to apprise one of the various aspects of procedures and routines that Exxon Nuclear uses with respect to its nuclear materials physical inventory program. The presentation describes how plant physical inventories are planned and taken. The description includes the planning and preparation for taking the inventory, the clean-out procedures for converting in-process material to measurable items, the administrative procedures for establishing independent inventory teams and for inventorying each inventory area, the verification procedures used to include previously measured tamper-safed items in the inventory, and lastly, procedures used to reconcile the inventory and calculate MUF (materials unaccounted for). The purpose of the session is to enable participants to: (1) understand the planning and pre-inventorty procedures and their importance; (2) understand the need for and the required intensity of clean-out procedures; (3) understand how inventory teams are formed, and how the inventory is conducted; (4) understand the distinction between inventory previously measured tamper-safed items and other materials not so characterized; (5) understand the reconciliation procedures; and (6) calculate a MUF given the book and inventory results

Formaldehyde-releasers: relationship to formaldehyde contact allergy. Contact allergy to formaldehyde and inventory of formaldehyde-releasers

DEFF Research Database (Denmark)

de Groot, Anton C; Flyvholm, Mari-Ann; Lensen, Gerda

2009-01-01

in the literature as formaldehyde-releasers, data are inadequate to consider them as such beyond doubt. Several (nomenclature) mistakes and outdated information are discussed. Formaldehyde and formaldehyde allergy are reviewed: applications, exposure scenarios, legislation, patch testing problems, frequency....... The frequency of contact allergy to formaldehyde is consistently higher in the USA (8-9%) than in Europe (2-3%). Patch testing with formaldehyde is problematic; the currently used 1% solution may result in both false-positive and false-negative (up to 40%) reactions. Determining the relevance of patch test...

Unified Communications for Space Inventory Management

Science.gov (United States)

Gifford, Kevin K.; Fink, Patrick W.; Barton, Richard; Ngo, Phong H.

2009-01-01

To help assure mission success for long-duration exploration activities, NASA is actively pursuing wireless technologies that promote situational awareness and autonomy. Wireless technologies are typically extensible, offer freedom from wire tethers, readily support redundancy, offer potential for decreased wire weight, and can represent dissimilar implementation for increased reliability. In addition, wireless technologies can enable additional situational awareness that otherwise would be infeasible. For example, addition of wired sensors, the need for which might not have been apparent at the outset of a program, night be extremely costly due in part to the necessary routing of cables through the vehicle. RFID, or radio frequency identification, is a wireless technology with the potential for significant savings and increased reliability and safety in space operations. Perhaps the most obvious savings relate to the application of inventory management. A fully automated inventory management system is highly desirable for long-term sustaining operations in space environments. This assertion is evidenced by inventory activities on the International Space Station, which represents the most extensive inventory tracking experience base in the history of space operations. In the short tern, handheld RFID readers offer substantial savings owing to reduced crew time for inventory audits. Over the long term, a combination of improved RFID technology and operational concepts modified to fully utilize the technology should result in space based inventory management that is highly reliable and requires very little crew time. In addition to inventory management, RFID is likely to find space applications in real-time location and tracking systems. These could vary from coarse-resolution RFID portals to the high resolution afforded by ultra-wideband (UWB) RFID. Longer range RFID technologies that leverage passive surface acoustic wave (SAW) devices are being investigated to

Inventory - Dollars and sense

International Nuclear Information System (INIS)

Samson, J.R.

1992-01-01

Nuclear utilities are becoming more aware of the importance of having an inventory investment that supports two opposing philosophies. The business philosophy wants a minimal inventory investment to support a better return on invested dollars. This increase in return comes from having the dollars available to invest versus having the money tied up in inventory sitting on the shelf. The opposing viewpoint is taken by maintenance/operations organizations, which desire the maximum inventory available on-site to repair any component at any time to keep the units on-line at all times. Financial managers also want to maintain cash flow throughout operations so that plants run without interruptions. Inventory management is therefore a mixture of financial logistics with an operation perspective in mind. A small amount of common sense and accurate perception also help. The challenge to the materials/inventory manager is to optimize effectiveness of the inventory by having high material availability at the lowest possible cost

Carbon 14 distribution in irradiated BWR fuel cladding and released carbon 14 after aqueous immersion of 6.5 years

Energy Technology Data Exchange (ETDEWEB)

Sakuragi, T. [Radioactive Waste Management Funding and Research Center, Tsukishima 1-15-7, Chuo City, Tokyo, 104-0052 (Japan); Yamashita, Y.; Akagi, M.; Takahashi, R. [TOSHIBA Corporation, Ukishima Cho 4-1, Kawasaki Ward, Kawasaki, 210-0862 (Japan)

2016-07-01

Spent fuel cladding which is highly activated and strongly contaminated is expected to be disposed of in an underground repository. A typical activation product in the activated metal waste is carbon 14 ({sup 14}C), which is mainly generated by the {sup 14}N(n,p){sup 14}C reaction and produces a significant exposure dose due to the large inventory, long half-life (5730 years), rapid release rate, and the speciation and consequent migration parameters. In the preliminary Japanese safety case, the release of radionuclides from the metal matrix is regarded as the corrosion-related congruent release, and the cladding oxide layer is regarded as a source of instant release fraction (IRF). In the present work, specific activity of {sup 14}C was measured using an irradiated BWR fuel cladding (Zircaloy-2, average rod burnup of 41.6 GWd/tU) which has an external oxide film having a thickness of 25.3 μm. The {sup 14}C specific activity of the base metal was 1.49*10{sup 4} Bq/g, which in the corresponding burnup is comparable to values in the existing literature, which were obtained from various irradiated claddings. Although the specific activity in oxide was 2.8 times the base metal activity due to the additive generation by the {sup 17}O(n,α){sup 14}C reaction, the {sup 14}C abundance in oxide was less than 10% of total inventory. A static leaching test using the cladding tube was carried out in an air-tight vessel filled with a deoxygenated dilute NaOH solution (pH of 12.5) at room temperature. After 6.5 years, {sup 14}C was found in each leachate fraction of gas phase and dissolved organics and inorganics, the total of which was less than 0.01% of the {sup 14}C inventory of the immersed cladding tube. A simple calculation based on the congruent release with Zircaloy corrosion has suggested that the 96.7% of released {sup 14}C was from the external oxide layer and 3.3% was from the base Zircaloy metal. However, both the {sup 14}C abundance and the low leaching rate

Quality manual for the Danish greenhouse gas inventory

DEFF Research Database (Denmark)

Nielsen, Ole-Kenneth; Plejdrup, Marlene Schmidt; Winther, Morten

The report outlines the quality work undertaken by the emission inventory group at the Department of Environmental Science, Aarhus University in connection with the preparation and reporting of the Danish greenhouse gas inventory. The report updates and expands on the first version of the quality...... manual published in 2005. The report fulfils the mandatory requirements for a quality assurance/quality control (QA/QC) plan as lined out in the UNFCCC reporting guidelines and the specifications related to reporting under the Kyoto Protocol. The report describes all elements of the internal QC...... procedures as well as the QA and verification activities carried out in connection with the Danish greenhouse gas inventory....

Inventory control strategies

International Nuclear Information System (INIS)

Primrose, D.

1998-01-01

Finning International Inc. is in the business of selling, financing and servicing Caterpillar and complementary equipment. Its main markets are in western Canada, Britain and Chile. This paper discusses the parts inventory strategies system for Finning (Canada). The company's territory covers British Columbia, Alberta, the Yukon and the Northwest Territories. Finning's parts inventory consists of 80,000 component units valued at more than $150 M. Distribution centres are located in Langley, British Columbia and Edmonton, Alberta. To make inventory and orders easier to control, Finning has designed a computer-based system, with software written exclusively for Caterpillar dealers. The system makes use of a real time electronic interface with all Finning locations, plus all Caterpillar facilities and other dealers in North America. Details of the system are discussed, including territorial stocking procedures, addition to stock, exhaustion of stock, automatic/suggest order controls, surplus inventory management, and procedures for jointly managed inventory. 3 tabs., 1 fig

WW LCI v2: A second-generation life cycle inventory model for chemicals discharged to wastewater systems.

Science.gov (United States)

Kalbar, Pradip P; Muñoz, Ivan; Birkved, Morten

2018-05-01

We present a second-generation wastewater treatment inventory model, WW LCI 2.0, which on many fronts represents considerable advances compared to its previous version WW LCI 1.0. WW LCI 2.0 is a novel and complete wastewater inventory model integrating WW LCI 1.0, i.e. a complete life cycle inventory, including infrastructure requirement, energy consumption and auxiliary materials applied for the treatment of wastewater and disposal of sludge and SewageLCI, i.e. fate modelling of chemicals released to the sewer. The model is expanded to account for different wastewater treatment levels, i.e. primary, secondary and tertiary treatment, independent treatment by septic tanks and also direct discharge to natural waters. Sludge disposal by means of composting is added as a new option. The model also includes a database containing statistics on wastewater treatment levels and sludge disposal patterns in 56 countries. The application of the new model is demonstrated using five chemicals assumed discharged to wastewater systems in four different countries. WW LCI 2.0 model results shows that chemicals such as diethylenetriamine penta (methylene phosphonic acid) (DTPMP) and Diclofenac, exhibit lower climate change (CC) and freshwater ecotoxicity (FET) burdens upon wastewater treatment compared to direct discharge in all country scenarios. Results for Ibuprofen and Acetaminophen (more readily degradable) show that the CC burden depends on the country-specific levels of wastewater treatment. Higher treatment levels lead to lower CC and FET burden compared to direct discharge. WW LCI 2.0 makes it possible to generate complete detailed life cycle inventories and fate analyses for chemicals released to wastewater systems. Our test of the WW LCI 2.0 model with five chemicals illustrates how the model can provide substantially different outcomes, compared to conventional wastewater inventory models, making the inventory dependent upon the atomic composition of the molecules

Cross-cultural validation of the child abuse potential inventory in Belgium (Flanders) : Relations with demographic characteristics and parenting problems

NARCIS (Netherlands)

Grietens, Hans; De Haene, Lucia; Uyttebroek, Karolien

This study examined the reliability and the validity of the Dutch CAP Inventory, a screening instrument that measures parents' potential for child physical abuse (Milner, The Child Abuse Potential Inventory: Manual (2nd ed.), Psytec, Webster, NC, 1986). The CAP Inventory and measures on parenting

Materials control and accountability challenges associated with plutonium inventories

International Nuclear Information System (INIS)

Crawford, D.W.

1996-01-01

There are currently many initiatives underway within the Department of Energy (DOE) to safely and securely manage large plutonium inventories arising from weapons dismantlement, changing missions and facility operations. Plutonium inventory information is increasingly accessible to the public as a result of the secretary of energy's openness initiative. As a result, knowledge of these inventories and levels to which the department has accounted for and controlled these inventories, will be under increased scrutiny from a variety of interest groups. The quality of this accountability data and what this data means will greatly influence the public's perception of how the US is protecting its plutonium inventories. In addition, the department's safeguards program provides an essential basis for the application of International Atomic Energy Agency (IAEA) safeguards that, in addition to possibly other international control regimes, will be in place over a large portion of these future inventories. The capability and functionality of the department's nuclear safeguards program will be important contributors to the success of US programs for the responsible stewardship of these vast plutonium inventories. This paper discusses some of the challenges, in terms of specific issues relating to one part of the department's safeguards program--materials control and accountability (MC and A)--to meet the growing domestic and international requirements and expectations associated with these plutonium inventories

Materials control and accountability challenges associated with plutonium inventories

Energy Technology Data Exchange (ETDEWEB)

Crawford, D.W. [USDOE Office of Safeguards and Security, Washington, DC (United States)

1996-07-01

There are currently many initiatives underway within the Department of Energy (DOE) to safely and securely manage large plutonium inventories arising from weapons dismantlement, changing missions and facility operations. Plutonium inventory information is increasingly accessible to the public as a result of the secretary of energy`s openness initiative. As a result, knowledge of these inventories and levels to which the department has accounted for and controlled these inventories, will be under increased scrutiny from a variety of interest groups. The quality of this accountability data and what this data means will greatly influence the public`s perception of how the US is protecting its plutonium inventories. In addition, the department`s safeguards program provides an essential basis for the application of International Atomic Energy Agency (IAEA) safeguards that, in addition to possibly other international control regimes, will be in place over a large portion of these future inventories. The capability and functionality of the department`s nuclear safeguards program will be important contributors to the success of US programs for the responsible stewardship of these vast plutonium inventories. This paper discusses some of the challenges, in terms of specific issues relating to one part of the department`s safeguards program--materials control and accountability (MC and A)--to meet the growing domestic and international requirements and expectations associated with these plutonium inventories.

Toward an Assessment of the Global Inventory of Present-Day Mercury Releases to Freshwater Environments

Directory of Open Access Journals (Sweden)

David Kocman

2017-02-01

Full Text Available Aquatic ecosystems are an essential component of the biogeochemical cycle of mercury (Hg, as inorganic Hg can be converted to toxic methylmercury (MeHg in these environments and reemissions of elemental Hg rival anthropogenic Hg releases on a global scale. Quantification of effluent Hg releases to aquatic systems globally has focused on discharges to the global oceans, rather than contributions to freshwater systems that affect local exposures and risks associated with MeHg. Here we produce a first-estimate of sector-specific, spatially resolved global aquatic Hg discharges to freshwater systems. We compare our release estimates to atmospheric sources that have been quantified elsewhere. By analyzing available quantitative and qualitative information, we estimate that present-day global Hg releases to freshwater environments (rivers and lakes associated with anthropogenic activities have a lower bound of ~1000 Mg· a−1. Artisanal and small-scale gold mining (ASGM represents the single largest source, followed by disposal of mercury-containing products and domestic waste water, metal production, and releases from industrial installations such as chlor-alkali plants and oil refineries. In addition to these direct anthropogenic inputs, diffuse inputs from land management activities and remobilization of Hg previously accumulated in terrestrial ecosystems are likely comparable in magnitude. Aquatic discharges of Hg are greatly understudied and further constraining associated data gaps is crucial for reducing the uncertainties in the global biogeochemical Hg budget.

World Glacier Inventory

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The World Glacier Inventory (WGI) contains information for over 130,000 glaciers. Inventory parameters include geographic location, area, length, orientation,...

Measured tritium in groundwater related to atmospheric releases from the Marcoule nuclear site

International Nuclear Information System (INIS)

Levy, F.; Clech, A.; Crochet, P.

1996-01-01

Tritium is released into the atmosphere during normal operation from the industrial facilities operated by COGEMA at Marcoule; over a 1 5-year period covered by this study (1979-1994) the quantities ranged from 4940 to 520 TBq·yr -1 . Atmospheric release in rainy weather results in tritium migration into the ground water by a series of mechanisms associated with the water cycle. COGEMA monitors the ground water by means of bore holes. Atmospheric monitoring is also routinely performed; data on the tritium activity concentration in the air and rainwater are available for the same time period. A simplified observation suggests a relation between the atmospheric tritium release and the ground water radioactivity. In 1994, the activity ranged from 100 to 200 Bq·l -1 in the boreholes located 1 km and 2 km downwind from the point of release, diminishing with the distance to less than 20 Bq·l -1 at about 3 km. The authors attempted to model two types of transfers: atmospheric transfer from the release chimney to the borehole, and transfer in the alluvial ground water. The aquifer comprises the alluvial deposits forming the Codolet plain extending to the south of Marcoule, downwind from the point of atmospheric tritium release. The hydrogeology of the entire Marcoule site has been described in previous studies by the French bureau of geological and mineralogical research (BRGM) and ANTEA. (author)

General technical requirements (GTR) for inventory monitoring systems (IMS) for the trilateral initiative

International Nuclear Information System (INIS)

Pshakin, Gennady M.; Kuleshov, I.; Shea, T.; Puckett, J.M.; Zhukov, I.; Mangan, Dennis L.; Matter, John C.; Waddoups, I.; Smathers, D.; Abhold, M.E.; Hsue, S.-T.; Chiaro, P.

2002-01-01

Pursuant to the Trilateral Initiative, the three parties (The Russian Federation, the United States, and the International Atomic Energy Agency) have been engaged in discussions concerning the structure of reliable monitoring systems for storage facilities having large inventories. The intent of these monitoring systems is to provide the capability for the IAEA to maintain continuity of knowledge in a sufficiently reliable manner that should there be equipment failure, loss of continuity of knowledge would be restricted to a small population of the inventory, and thus reinventory of the stored items would be minimized These facility-specific monitoring systems, referred to as Inventory Monitoring Systems (IMS) are to provide the principal means for the M A to assure that the containers of fissile material remain accounted under the Verification Agreements which are to be concluded between the IAEA and the Russian Federation and the lAEA and the United States for the verification of weapon-origin and other fissile material specified by each State as released from its defense programs. A technical experts working group for inventory monitoring systems has been meeting since Feb- of 2000 to formulate General Technical Requirements (GTR) for Inventory Monitoring Systems for the Trilateral Initiative. Although provisional agreement has been reached by the three parties concerning the GTR, it is considered a living document that can be updated as warranted by the three parties. This paper provides a summary of the GTR as it currently exists.

Vendor-managed inventory

DEFF Research Database (Denmark)

Govindan, Kannan

2013-01-01

Vendor-managed inventory (VMI) represents the methodology through which the upstream stage of a supply chain (vendor) takes responsibility for managing the inventories at the downstream stage (customer) based on previously agreed limits. VMI is another method by which supply chains can be managed...... review, we have identified six dimensions of VMI: namely, inventory, transportation, manufacturing, general benefits, coordination/collaboration, and information sharing. In addition, there are, three methodological classifications: modelling, simulation, and case studies. Finally, we will consider...

User's guide to FBASE: Relational database software for managing R1/R4 (Northern/Intermountain Regions) fish habitat inventory data

Science.gov (United States)

Sherry P. Wollrab

1999-01-01

FBASE is a microcomputer relational database package that handles data collected using the R1/R4 Fish and Fish Habitat Standard Inventory Procedures (Overton and others 1997). FBASE contains standard data entry screens, data validations for quality control, data maintenance features, and summary report options. This program also prepares data for importation into an...

Scenarios for potential radionuclide release from marine reactors dumped in the Kara Sea

International Nuclear Information System (INIS)

Lynn, N.; Mount, M.; Gussgard, K.

1995-01-01

The largest inventory of radioactive materials dumped in the Kara Sea by the former Soviet Union comes from the spent nuclear fuel (SNF) of seven marine reactors, the current (1994) inventory of which makes a total of approximately 4.7x10 15 Bq. In progressing its work for the International Arctic Seas Assessment Project, under the auspices of the International Atomic Energy Agency, the Source Term Working Group has analysed the Source Term and subsequently developed a number of model scenarios for the potential release patterns of radionuclides into the Kara Sea from the SNF and activated components dumped within the marine reactors.These models are based on the present and future conditions of the barrier materials and their configuration within the dumped objects. They account for progressive corrosion of the outer and inner steel barriers, breakdown of the organic fillers, and degradation and leaching from the SNFs. Annual release rates are predicted to four thousand years into the future. 5 refs., 1 fig., 1 tab

Toxic Release Inventory (TRI) Facility Points, Region 9, 2012, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — A federal law called the Emergency Planning and Community Right to Know Act (EPCRA) gives the public the right to know about toxic chemicals being released into the...

Toxic Release Inventory (TRI) Facility Points, Region 9, 2014, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — A federal law called the Emergency Planning and Community Right to Know Act (EPCRA) gives the public the right to know about toxic chemicals being released into the...

Toxic Release Inventory (TRI) Facility Points, Region 9, 2011, US EPA Region 9

Data.gov (United States)

U.S. Environmental Protection Agency — A federal law called the Emergency Planning and Community Right to Know Act (EPCRA) gives the public the right to know about toxic chemicals being released into the...

Using a detailed inventory of a large wastewater treatment plant to estimate the relative importance of construction to the overall environmental impacts.

Science.gov (United States)

Morera, Serni; Corominas, Lluís; Rigola, Miquel; Poch, Manel; Comas, Joaquim

2017-10-01

The aim of this work is to quantify the relative contribution to the overall environmental impact of the construction phase compared to the operational phase for a large conventional activated sludge wastewater treatment plant (WWTP). To estimate these environmental impacts, a systematic procedure was designed to obtain the detailed Life Cycle Inventories (LCI) for civil works and equipment, taking as starting point the construction project budget and the list of equipment installed at the Girona WWTP, which are the most reliable information sources of materials and resources used during the construction phase. A detailed inventory is conducted by including 45 materials for civil works and 1,240 devices for the equipment. For most of the impact categories and different life spans of the WWTP, the contribution of the construction phase to the overall burden is higher than 5% and, especially for metal depletion, the impact of construction reaches 63%. When comparing to the WWTP inventories available in Ecoinvent the share of construction obtained in this work is about 3 times smaller for climate change and twice higher for metal depletion. Concrete and reinforcing steel are the materials with the highest contribution to the civil works phase and motors, pumps and mobile and transport equipment are also key equipment to consider during life cycle inventories of WWTPs. Additional robust inventories for similar WWTP can leverage this work by applying the factors (kg of materials and energy per m 3 of treated water) and guidance provided. Copyright © 2017 Elsevier Ltd. All rights reserved.

Housing Inventory Count

Data.gov (United States)

Department of Housing and Urban Development — This report displays the data communities reported to HUD about the nature of their dedicated homeless inventory, referred to as their Housing Inventory Count (HIC)....

27 CFR 40.201 - Inventories.

Science.gov (United States)

2010-04-01

... PROCESSED TOBACCO Operations by Manufacturers of Tobacco Products Inventories and Reports § 40.201 Inventories. Every manufacturer of tobacco products shall make true and accurate inventories on Form 5210.9... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Inventories. 40.201...

Use of ELOCA.Mk5 to calculate transient fission product release from CANDU fuel elements

International Nuclear Information System (INIS)

Walker, J.R.; de Vaal, J.W.; Arimescu, V.I.; McGrady, T.G.; Wong, C.

1992-04-01

A change in fuel element power output, or a change in heat transfer conditions, will result in an immediate change in the temperature distribution in a fuel element. The temperature distribution change will be accompanied by concomitant changes in fuel stress distribution that lead, in turn, to a release of fission products to the fuel-to-sheath gap. It is important to know the inventory of fission products in the fuel-to-sheath gap, because this inventory is a major component of the source term for many postulated reactor accidents. ELOCA.Mk5 is a FORTRAN-77 computer code that has been developed to estimate transient releases to the fuel-to-sheath gap in CANDU reactors. ELOCA.Mk5 is an integration of the FREEDOM fission product release model into the ELOCA fuel element thermo-mechanical code. The integration of FREEDOM into ELOCA allows ELOCA.Mk5 to model the feedback mechanisms between the fission product release and the thermo-mechanical response of the fuel element. This paper describes the physical model, gives details of the ELOCA.Mkt code, and describes the validation of the model. We demonstrate that the model gives good agreement with experimental results for both steady state and transient conditions

Monitoring and inventorying of the pollutant emissions from thermal power plants

International Nuclear Information System (INIS)

Vladescu, Gherghina; Iordache, Daniela; Iordache, Victorita; Ciomaga, Carmencita; Matei, Magdalena; Ilie, Ion; Motiu, Cornel

2001-01-01

Pollution due to emissions discharged in atmosphere as a result of human (anthropogenic) activities and the related environmental effects, such as acid depositions, land quality degradation, global warming/climate changes, building degradation, ozone layer depletion required the monitoring and inventorying of the polluting emissions at the local, regional and global levels. The paper briefly presents the international requirements concerning the development of a polluting emission inventory, the European methodologies for air polluting emission inventorying, programs and methodologies used in the Romanian electricity production sector for inventorying the polluting emissions and calculation of the dispersion of the pollutants discharged in the atmosphere. (author)

Spare Parts Inventory Management for the Next Generation Finnish Defense Force Fighter Fleet

Science.gov (United States)

2017-12-01

might benefit the end user most in high criticality or high cost classification classes: CrA, CrB, EA and EB. H. LEAD TIME EFFECTS Lead time is...NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release. Distribution is unlimited. SPARE PARTS INVENTORY MANAGEMENT...Eddine Dahel THIS PAGE INTENTIONALLY LEFT BLANK i REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704–0188 Public reporting burden for this collection

Center for Integrated Nanotechnologies (CINT) Chemical Release Modeling Evaluation

Energy Technology Data Exchange (ETDEWEB)

Stirrup, Timothy Scott [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-12-20

This evaluation documents the methodology and results of chemical release modeling for operations at Building 518, Center for Integrated Nanotechnologies (CINT) Core Facility. This evaluation is intended to supplement an update to the CINT [Standalone] Hazards Analysis (SHA). This evaluation also updates the original [Design] Hazards Analysis (DHA) completed in 2003 during the design and construction of the facility; since the original DHA, additional toxic materials have been evaluated and modeled to confirm the continued low hazard classification of the CINT facility and operations. This evaluation addresses the potential catastrophic release of the current inventory of toxic chemicals at Building 518 based on a standard query in the Chemical Information System (CIS).

Spatial GHG Inventory: Analysis of Uncertainty Sources. A Case Study for Ukraine

International Nuclear Information System (INIS)

Bun, R.; Gusti, M.; Kujii, L.; Tokar, O.; Tsybrivskyy, Y.; Bun, A.

2007-01-01

A geoinformation technology for creating spatially distributed greenhouse gas inventories based on a methodology provided by the Intergovernmental Panel on Climate Change and special software linking input data, inventory models, and a means for visualization are proposed. This technology opens up new possibilities for qualitative and quantitative spatially distributed presentations of inventory uncertainty at the regional level. Problems concerning uncertainty and verification of the distributed inventory are discussed. A Monte Carlo analysis of uncertainties in the energy sector at the regional level is performed, and a number of simulations concerning the effectiveness of uncertainty reduction in some regions are carried out. Uncertainties in activity data have a considerable influence on overall inventory uncertainty, for example, the inventory uncertainty in the energy sector declines from 3.2 to 2.0% when the uncertainty of energy-related statistical data on fuels combusted in the energy industries declines from 10 to 5%. Within the energy sector, the 'energy industries' subsector has the greatest impact on inventory uncertainty. The relative uncertainty in the energy sector inventory can be reduced from 2.19 to 1.47% if the uncertainty of specific statistical data on fuel consumption decreases from 10 to 5%. The 'energy industries' subsector has the greatest influence in the Donetsk oblast. Reducing the uncertainty of statistical data on electricity generation in just three regions - the Donetsk, Dnipropetrovsk, and Luhansk oblasts - from 7.5 to 4.0% results in a decline from 2.6 to 1.6% in the uncertainty in the national energy sector inventory

Functional Assessment Inventory Manual.

Science.gov (United States)

Crewe, Nancy M.; Athelstan, Gary T.

This manual, which provides extensive new instructions for administering the Functional Assessment Inventory (FAI), is intended to enable counselors to begin using the inventory without undergoing any special training. The first two sections deal with the need for functional assessment and issues in the development and use of the inventory. The…

ICPP water inventory study project summary report

International Nuclear Information System (INIS)

Richards, B.T.

1994-01-01

The Idaho Chemical Processing Plant (ICPP) Water inventory Study was initiated in September 1993 with the formation of a joint working group consisting of representatives from DOE-ID, State of Idaho INEL Oversight Program, US Geological Survey, and INEL employees to investigate three issues that had been identified by the INEL Oversight Program at ICPP: (1) the water inventory imbalance at ICPP, (2) the source of water infiltrating into the Tank Farm vault sumps, and (3) the source of water providing potential recharge to perched water bodies underlying ICPP. These issues suggested that water was being lost from the ICPP distribution system. The INEL Oversight Program was concerned that the unaccounted for water at ICPP could be spreading contaminants that have been released over the past 40 years of operations of ICPP, possibly to the Snake River Plain Aquifer. This report summarizes the findings of each of the component investigations that were undertaken to resolve each of the three issues. Concerns about the risk of spreading contaminants will be resolved as part of the Remedial Investigation/Feasibility Study being undertaken at ICPP in compliance with the Federal Facility Agreement and Consent Order between DOE-H), EPA, and the State of Idaho. This report will be a key input to that study

Understanding drug-related mortality in released prisoners: a review of national coronial records

Directory of Open Access Journals (Sweden)

Andrews Jessica Y

2012-04-01

Full Text Available Abstract Background The prisoner population is characterised by a high burden of disease and social disadvantage, and ex-prisoners are at increased risk of death following release. Much of the excess mortality can be attributed to an increased risk of unnatural death, particularly from drug overdose; however, relatively few studies have investigated the circumstances surrounding drug-related deaths among released prisoners. This study aimed to explore and compare the circumstances of death for those who died from accidental drug-related causes to those who died from all other reportable causes. Methods A nationwide search of the Australian National Coroners Information System (NCIS was conducted to identify reportable deaths among ex-prisoners from 2000 to 2007. Using a structured coding form, NCIS records for these cases were interrogated to explore causes and circumstances of death. Results Coronial records for 388 deceased ex-prisoners were identified. Almost half of these deaths were a result of accidental drug-related causes (45%. The majority of accidental drug-related deaths occurred in a home environment, and poly-substance use at or around the time of death was common, recorded in 72% of drug-related deaths. Ex-prisoners who died of accidental drug-related causes were on average younger and less likely to be Indigenous, born in Australia, married, or living alone at or around the time of death, compared with those who died from all other reportable causes. Evidence of mental illness or self-harm was less common among accidental drug-related deaths, whereas evidence of previous drug overdose, injecting drug use, history of heroin use and history of drug withdrawal in the previous six months were more common. Conclusions Drug-related deaths are common among ex-prisoners and often occur in a home (vs. public setting. They are often associated with use of multiple substances at or around the time of death, risky drug-use patterns, and even

Optimal fuel inventory strategies

International Nuclear Information System (INIS)

Caspary, P.J.; Hollibaugh, J.B.; Licklider, P.L.; Patel, K.P.

1990-01-01

In an effort to maintain their competitive edge, most utilities are reevaluating many of their conventional practices and policies in an effort to further minimize customer revenue requirements without sacrificing system reliability. Over the past several years, Illinois Power has been rethinking its traditional fuel inventory strategies, recognizing that coal supplies are competitive and plentiful and that carrying charges on inventory are expensive. To help the Company achieve one of its strategic corporate goals, an optimal fuel inventory study was performed for its five major coal-fired generating stations. The purpose of this paper is to briefly describe Illinois Power's system and past practices concerning coal inventories, highlight the analytical process behind the optimal fuel inventory study, and discuss some of the recent experiences affecting coal deliveries and economic dispatch

MANAGEMENT OF INVENTORIES IN AN ENTEPRISE IN THE CONTEXT OF PRODUCTION CONTINUITY

Directory of Open Access Journals (Sweden)

Izabela EMERLING

2014-04-01

Full Text Available Inventories are a very important category in the accounting of every enterprise. Inventory management is one of the major decision‐making areas for the company’s management board. Proper inventory management allows reducing total costs and increasing the quality of production, which is the goal of an integrated management system. Proper financial management can also positively affect the maintenance of liquidity in the company. The purpose of this article is to present issues related to inventory management in a company in the context of continuity of production and fluidity of a subject.

A single-item inventory model for expected inventory order crossovers

NARCIS (Netherlands)

Riezebos, J.; Gaalman, G.J.C.

2009-01-01

Expected inventory order crossovers Occur if at the moment of ordering it is expected that orders will not arrive in the sequence they are ordered. Recent research has shown that (it) expected inventory order crossovers will be encountered more frequently in future, and that (b) use of a myopic

Controlling Inventory: Real-World Mathematical Modeling

Science.gov (United States)

Edwards, Thomas G.; Özgün-Koca, S. Asli; Chelst, Kenneth R.

2013-01-01

Amazon, Walmart, and other large-scale retailers owe their success partly to efficient inventory management. For such firms, holding too little inventory risks losing sales, whereas holding idle inventory wastes money. Therefore profits hinge on the inventory level chosen. In this activity, students investigate a simplified inventory-control…

New developments in emissions inventory activity along the northern border region of Mexico

Energy Technology Data Exchange (ETDEWEB)

Oliver, W.R.; Dickson, R.J.; Creelman, L.W. [Radian International LLC, Sacramento, CA (United States)] [and others

1996-12-31

The development and evaluation of emissions data for sources located along the Mexico/US border have accelerated over the past few years. This paper examines several new activities in emissions inventory development for the northern border of Mexico. Reviewed in this paper are the following recent developments that will lead to improved inventories for Mexico: development of inventory educational materials; creation of inventory manuals; estimation of emissions for unique sources; emissions-related studies; and identification of key research needs for Mexico inventories. Some of these activities are building a greater capacity in Mexico to construct emissions estimates. These topics are reviewed from the perspective of improving Mexico emissions inventories and emissions estimation capabilities.

[Inventories of atmospheric arsenic emissions from coal combustion in China, 2005].

Science.gov (United States)

Tian, He-Zhong; Qu, Yi-Ping

2009-04-15

Anthropogenic arsenic (As) emitted from coal combustion is one of key trace elements leading to negative air pollution and national economy loss. It is of great significance to estimate the atmospheric arsenic emission for proposing relevant laws or regulations and selecting proper pollution control technologies. The inventories of atmospheric arsenic emissions from coal combustion in China were evaluated by adopting the emission factor method based on fuel consumption. Arsenic emission sources were firstly classified into several categories by economic sectors, combustion types and pollution control technologies. Then, according to provincial coal consumption and averaged arsenic concentration in the feed fuel, the inventories of atmospheric arsenic emission from coal combustion in China in 2005 were established. Coal outputand consumption in China in 2005 were 2,119.8 and 2,099.8 Mt, respectively. The total emissions of arsenic released into the atmosphere in 2005 in China were estimated at about 1,564.4 t, and Shandong ranked the largest province with 144.4 t arsenic release, followed by Hunan (141.1 t), Hebei (108.5 t), Henan (77.7 t), and Jiangsu (77.0 t), which were mainly concentrated in the eastern and central provinces of China. The arsenic emissions were largely emitted by industry sector (818.8 t) and thermal power generation sector (303.4 t), contributing 52.3% and 19.4% of the totals, respectively. About 375.5 t arsenic was estimated to be released into the atmosphere in the form of gas phase in China in 2005, with a share of 24% of the totals. In general, arsenic pollution control from coal combustion should be highlighted for the power and industry sectors in the whole country. However, arsenic poisoning caused by residential coal burning should also be paid great attention in some areas such as Xinjiang, Gansu, Qinghai and Guishou.

21 CFR 1304.11 - Inventory requirements.

Science.gov (United States)

2010-04-01

... the inventory of the registered location to which they are subject to control or to which the person... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Inventory requirements. 1304.11 Section 1304.11... REGISTRANTS Inventory Requirements § 1304.11 Inventory requirements. (a) General requirements. Each inventory...

Model of inventory replenishment in periodic review accounting for the occurrence of shortages

Directory of Open Access Journals (Sweden)

Stanisław Krzyżaniak

2014-03-01

Full Text Available Background: Despite the development of alternative concepts of goods flow management, the inventory management under conditions of random variations of demand is still an important issue, both from the point of view of inventory keeping and replenishment costs and the service level measured as the level of inventory availability. There is a number of inventory replenishment systems used in these conditions, but they are mostly developments of two basic systems: reorder point-based and periodic review-based. The paper deals with the latter system. Numerous researches indicate the need to improve the classical models describing that system, the reason being mainly the necessity to adapt the model better to the actual conditions. This allows a correct selection of parameters that control the used inventory replenishment system and - as a result - to obtain expected economic effects. Methods: This research aimed at building a model of the periodic review system to reflect the relations (observed during simulation tests between the volume of inventory shortages and the degree of accounting for so-called deferred demand, and the service level expressed as the probability of satisfying the demand in the review and the inventory replenishment cycle. The following model building and testing method has been applied: numerical simulation of inventory replenishment - detailed analysis of simulation results - construction of the model taking into account the regularities observed during the simulations - determination of principles of solving the system of relations creating the model - verification of the results obtained from the model using the results from simulation. Results: Presented are selected results of calculations based on classical formulas and using the developed model, which describe the relations between the service level and the parameters controlling the discussed inventory replenishment system. The results are compared to the simulation

Update and improvement of the global krypton-85 emission inventory.

Science.gov (United States)

Ahlswede, Jochen; Hebel, Simon; Ross, J Ole; Schoetter, Robert; Kalinowski, Martin B

2013-01-01

Krypton-85 is mainly produced in nuclear reactors by fission of uranium and plutonium and released during chopping and dissolution of spent fuel rods in nuclear reprocessing facilities. As noble gas it is suited as a passive tracer for evaluation of atmospheric transport models. Furthermore, research is ongoing to assess its quality as an indicator for clandestine reprocessing activities. This paper continues previous efforts to compile a comprehensive historic emission inventory for krypton-85. Reprocessing facilities are the by far largest emitters of krypton-85. Information on sources and calculations used to derive the annual krypton-85 emission is provided for all known reprocessing facilities in the world. In addition, the emission characteristics of two plants, Tokai (Japan) and La Hague (France), are analysed in detail using emission data with high temporal resolution. Other types of krypton-85 sources are power reactors, naval reactors and isotope production facilities. These sources contribute only little or negligible amounts of krypton-85 compared to the large reprocessing facilities. Taking the decay of krypton-85 into account, the global atmospheric inventory is estimated to about 5500 PBq at the end of 2009. The correctness if the inventory has been proven by meteorological simulations and its error is assumed to be in the range of a few percent. Copyright © 2012 Elsevier Ltd. All rights reserved.

An evaluation of vendor managed inventory practices from small and medium indian enterprises

DEFF Research Database (Denmark)

Shen, Lixin; Govindan, Kannan; Borade, Atul B.

2013-01-01

Vendor managed inventory has proven to be an effective tool for improving the supply chain performance by decreasing inventory-related costs and increasing customer service. It is quite evident from the literature that vendor managed inventory (VMI) has been successfully implemented in small...... and medium enterprises (SMEs). However, studies related to the implementation of VMI in Indian SMEs are very limited. Therefore, this study presents an empirical investigation of VMI practices in Indian SMEs using survey methodology. The paper evaluates the benefits, barriers, and effects of adopting VMI...

Fission-product release modelling in the ASTEC integral code: the status of the ELSA module

International Nuclear Information System (INIS)

Plumecocq, W.; Kissane, M.P.; Manenc, H.; Giordano, P.

2003-01-01

Safety assessment of water-cooled nuclear reactors encompasses potential severe accidents where, in particular, the release of fission products (FPs) and actinides into the reactor coolant system (RCS) is evaluated. The ELSA module is used in the ASTEC integral code to model all releases into the RCS. A wide variety of experiments is used for validation: small-scale CRL, ORNL and VERCORS tests; large-scale Phebus-FP tests; etc. Being a tool that covers intact fuel and degraded states, ELSA is being improved maximizing the use of information from degradation modelling. Short-term improvements will include some treatment of initial FP release due to intergranular inventories and implementing models for release of additional structural materials (Sn, Fe, etc.). (author)

Derivation of residual radionuclide inventory guidelines for implace closure of high-level waste tanks

International Nuclear Information System (INIS)

Yuan, L.; Yuan, Y.

1999-01-01

Residual radionuclide inventory guidelines were derived for the high-level waste tanks at a vitrification facility. The decommissioning scenario assumed for this derivation was that the tanks were to be stabilized at the present locations and the site is released for unrestricted use following a 100-year institutional control period. It was assumed that loss of institutional control would occur at 100-years following tank closure. The derivation of the residual radionuclide inventory guidelines was based on the requirement that the effective dose equivalent (EDE) to a hypothetical individual who lives in the vicinity of the site should not exceed a dose of 0.15 mSv/yr off-site and 5 mSv/yr on-site following closure of the tanks. The RESRAD computer code, modified for exposure scenarios specific for the site, was used for this evaluation. The results of the derivation indicate that the allowable off-site dose limit will not be exceeded. The estimated potential doses to individuals using water offsite from a creek are negligibly small fractions of the 0.15 mSv/yr allowable dose limit. With an assumed 3% heel remaining in the tanks, the estimated peak dose rate for the future offsite water user is about 0.00025 mSv/yr. The residual radionuclide inventory guidelines derived based on potential doses to the on-site resident farmer indicate that, with the exception of Tc-99 and C-14, a 3% heel remaining in the tanks would not result in doses exceeding the 5 mSv/yr allowable dose limit. For this on-site exposure scenario, the peak dose rates occur at about 2000 years after tank closure. The peak dose rate is calculated to be 25 mSv/yr, with greater than 99% produced by four radionuclides: C-14, Tc-99, Np-237, and Am-241. Ingestion of contaminated vegetation contributes most (90%) of the peak dose. Since the inventories used for the derivation are mostly estimated from fuel depletion calculations. There is a need to determine further the actual inventories of these

Application of Greenhouse Gas Inventory to Urban Rural Planning in China

Institute of Scientific and Technical Information of China (English)

Stanley; C.; T.; YIP

2013-01-01

Greenhouse Gas (GHG) inventory analysis provides crucial scientific basis to support the preparation of urban-rural planning policies on managing climate change. This article reviews current studies on GHG inventory in China and points out the short fall in translating these inventory data into specific local policies. It examines the issue of setting up the GHG inventory based on the statutory urban-rural planning systems in China. It enables the local government to set up a platform coordinating various city policies and to serve well as the platform for local emission mitigation and removal policies. The urban-rural planning GHG inventory system needs to address the issue of spatial boundary in accounting for local emission sources and origins with respect to the boundaries of planning area, and it must directly relate to the various statutory master plan policy contents and the local municipal government functional structure. Finally it presents a case study of applying the proposed inventory as a planning tool for Jiangyin at the Jiangsu Province.

Myopic control of stochastic inventories with intermittent updates: continuous versus periodic replenishment

OpenAIRE

M Shnaiderman

2012-01-01

A manufacturer who is responsible for supplying a retailer with a single product is considered. The retailer sells the product in response to stochastic demand and provides the manufacturer with periodic updates about his inventories. Replenishing the retailer's inventory under two myopic base-stock policies is addressed. These policies, referred to as vendor managed inventory, represent a relatively new approach to allocating responsibility in the replenishment process. Specifically, the man...

Procedure for taking physical inventories

International Nuclear Information System (INIS)

Boston, R.A.

1984-01-01

Physical inventories are taken periodically to meet Company, State and IAEA requirements. Those physical inventories may be verified by IAEA and/or State inspectors. This presentation describes in an introductory but detailed manner the approaches and procedures used in planning, preparing, conducting, reconciling and reporting physical inventories for the Model Plant. Physical inventories are taken for plant accounting purposes to provide an accurate basis for starting and closing the plant material balance. Physical inventories are also taken for safeguards purposes to provide positive assurance that the nuclear materials of concern are indeed present and accounted for

Fukushima - calculation of the reactor core inventory and storage pools Dai-ichi 1 to Dai-ichi 4, an estimation of a source term

International Nuclear Information System (INIS)

Krpelanova, M.; Carny, P.

2011-01-01

Inventory of the reactor core and spent fuel storage pool of the reactors at Dai-ichi 1 to Dai-ichi 4 was determined to need a realistic estimate of the source (released into the atmosphere environment) and modelling of radiological impact of the events in Fukushima NPP. Calculations of inventories were carried out by the methodology that is used in systems to support emergency response and crisis management anymore. Calculations were made based on a model that respects knowledge of real fuels and fuel cycles for individual reactors Dai-ichi. Necessary input data for training the model and calculate inventories are obtained from the IAEA PRIS database.

Radionuclide release calculations for SAR-08

International Nuclear Information System (INIS)

Thomson, Gavin; Miller, Alex; Smith, Graham; Jackson, Duncan

2008-04-01

Following a review by the Swedish regulatory authorities of the post-closure safety assessment of the SFR 1 disposal facility for low and intermediate waste (L/ILW), SAFE, the SKB has prepared an updated assessment called SAR-08. This report describes the radionuclide release calculations that have been undertaken as part of SAR-08. The information, assumptions and data used in the calculations are reported and the results are presented. The calculations address issues raised in the regulatory review, but also take account of new information including revised inventory data. The scenarios considered include the main case of expected behaviour of the system, with variants; low probability releases, and so-called residual scenarios. Apart from these scenario uncertainties, data uncertainties have been examined using a probabilistic approach. Calculations have been made using the AMBER software. This allows all the component features of the assessment model to be included in one place. AMBER has been previously used to reproduce results the corresponding calculations in the SAFE assessment. It is also used in demonstration of the IAEA's near surface disposal assessment methodology ISAM and has been subject to very substantial verification tests and has been used in verifying other assessment codes. Results are presented as a function of time for the release of radionuclides from the near field, and then from the far field into the biosphere. Radiological impacts of the releases are reported elsewhere. Consideration is given to each radionuclide and to each component part of the repository. The releases from the entire repository are also presented. The peak releases rates are, for most scenarios, due to organic C-14. Other radionuclides which contribute to peak release rates include inorganic C-14, Ni-59 and Ni-63. (author)

Radionuclide release calculations for SAR-08

Energy Technology Data Exchange (ETDEWEB)

Thomson, Gavin; Miller, Alex; Smith, Graham; Jackson, Duncan (Enviros Consulting Ltd, Wolverhampton (United Kingdom))

2008-04-15

Following a review by the Swedish regulatory authorities of the post-closure safety assessment of the SFR 1 disposal facility for low and intermediate waste (L/ILW), SAFE, the SKB has prepared an updated assessment called SAR-08. This report describes the radionuclide release calculations that have been undertaken as part of SAR-08. The information, assumptions and data used in the calculations are reported and the results are presented. The calculations address issues raised in the regulatory review, but also take account of new information including revised inventory data. The scenarios considered include the main case of expected behaviour of the system, with variants; low probability releases, and so-called residual scenarios. Apart from these scenario uncertainties, data uncertainties have been examined using a probabilistic approach. Calculations have been made using the AMBER software. This allows all the component features of the assessment model to be included in one place. AMBER has been previously used to reproduce results the corresponding calculations in the SAFE assessment. It is also used in demonstration of the IAEA's near surface disposal assessment methodology ISAM and has been subject to very substantial verification tests and has been used in verifying other assessment codes. Results are presented as a function of time for the release of radionuclides from the near field, and then from the far field into the biosphere. Radiological impacts of the releases are reported elsewhere. Consideration is given to each radionuclide and to each component part of the repository. The releases from the entire repository are also presented. The peak releases rates are, for most scenarios, due to organic C-14. Other radionuclides which contribute to peak release rates include inorganic C-14, Ni-59 and Ni-63. (author)

The Work-Related Flow Inventory: Construction and Initial Validation of the WOLF

Science.gov (United States)

Bakker, Arnold B.

2008-01-01

The WOrk-reLated Flow inventory (WOLF) measures flow at work, defined as a short-term peak experience characterized by absorption, work enjoyment, and intrinsic work motivation. Results of Study 1 among 7 samples of employees (total N=1346) from different occupational groups offer support for the factorial validity and reliability of the WOLF.…

Proceedings of the workshop on new diagnostics related to impurity release

International Nuclear Information System (INIS)

1979-10-01

There were three major objectives of this workshop. The first was to publicize the need for developing experimental techniques to study the questions of impurity generation and transport. The second reason was to have a public forum where several new approaches, including fluorescence spectroscopy, infrared photometry and surface analytic techniques, could have their relative advantages discussed. A third goal of the meeting was to arrive at a concensus as to what questions related to impurity release were of critical importance. The assembled notes are copies of viewgraphs presented at the meeting. In a few cases a summary, or even an expanded text, was provided by the authors

Control your inventory in a world of lean retailing.

Science.gov (United States)

Abernathy, F H; Dunlop, J T; Hammond, J H; Weil, D

2000-01-01

As retailers adopt lean retailing practices, manufacturers are feeling the pinch. Retailers no longer place large seasonal orders for goods in advance-instead, they require ongoing replenishment of stock, forcing manufacturers to predict demand and then hold substantial inventories indefinitely. Manufacturers now carry the cost of inventory risk--the possibility that demand will dry up and goods will have to be sold below cost. And as product proliferation increases, customer demand becomes harder to predict. Most manufacturers apply one inventory policy for all stock-keeping units in a product line. But the inventory demand for SKUs within the same product line can vary significantly. SKUs with high volume typically have little variation in weekly sales, while slow-selling SKUs can vary enormously in weekly sales. The greater the variation, the larger the inventory the manufacturer must hold relative to an SKU's expected weekly sales. By differentiating inventory policies at the SKU level, manufacturers can reduce inventories for the high-volume SKUs and increase them for the low-volume ones--and thereby improve the profit-ability of the entire line. SKU-level differentiation can also be applied to sourcing strategies. Instead of producing all the SKUs for a product line at a single location, either offshore at low cost or close to market at higher cost, manufacturers can typically do better by going for a mixed allocation. Low-variation goods should be produced mainly offshore, while high-variation goods are best made close to markets.

Fission gas release and fuel rod chemistry related to extended burnup

International Nuclear Information System (INIS)

1993-04-01

The purpose of the meeting was to review the state of the art in fission gas release and fuel rod chemistry related to extended burnup. The meeting was held in a time when national and international programmes on water reactor fuel irradiated in experimental reactors were still ongoing or had reached their conclusion, and when lead test assemblies had reached high burnup in power reactors and been examined. At the same time, several out-of-pile experiments on high burnup fuel or with simulated fuel were being carried out. As a result, significant progress has been registered since the last meeting, particularly in the evaluation of fuel temperature, the degradation of the global thermal conductivity with burnup and in the understanding of the impact on fission gas release. Fifty five participants from 16 countries and one international organization attended the meeting. 28 papers were presented. A separate abstract was prepared for each of the papers. Refs, figs, tabs and photos

Mercury emissions inventory for 2014 in Costa Rica using the PNUMA Toolkit to a N2 level

Directory of Open Access Journals (Sweden)

Julio César Murillo-Hernández

2017-12-01

Full Text Available The Minamata Convention was signed in October 2013 to protect human health and the environment from releases and anthropogenic emissions of elemental mercury and compounds containing this element.  When Costa Rica ratified this instrument, the country committed to develop and keep updated an inventory of emissions from the relevant sources of mercury. In the present work, the tool proposed by UNEP was used to generate the first mercury inventory at the N2 level of the country, which considers releases of mercury in air, water, soil, product and waste matrices. Taking 2014 as the reference year, the estimated mercury emission for Costa Rica was recorded at 5 052 kg, with an uncertainty interval between 2 675 kg and 10 525 kg; and the most important sectors in terms of the total emission were the extraction of gold with amalgamation (42 %, informal burning of waste (15 % and use of dental amalgams (10 %. The most impacted matrices were air (29 %, water (28 % and soil (21 %, respectively.

The order and volume fill rates in inventory control systems

DEFF Research Database (Denmark)

Thorstenson, Anders; Larsen, Christian

2014-01-01

This paper differentiates between an order (line) fill rate and a volume fill rate and specifies their performance for different inventory control systems. When the focus is on filling complete customer orders rather than total demanded quantity the order fill rate would be the preferred service...... level measure. The main result shows how the order and volume fill rates are related in magnitude. Earlier results derived for a single-item, single-stage, continuous review inventory system with backordering and constant lead times controlled by a base-stock policy are extended in different directions...... extensions consider more general inventory control review policies with backordering, as well as some relations between service measures. A particularly important result in the paper concerns an alternative service measure, the customer order fill rate, and shows how this measure always exceeds the other two...

Initial Radionuclide Inventories

Energy Technology Data Exchange (ETDEWEB)

H. Miller

2004-09-19

The purpose of this analysis is to provide an initial radionuclide inventory (in grams per waste package) and associated uncertainty distributions for use in the Total System Performance Assessment for the License Application (TSPA-LA) in support of the license application for the repository at Yucca Mountain, Nevada. This document is intended for use in postclosure analysis only. Bounding waste stream information and data were collected that capture probable limits. For commercially generated waste, this analysis considers alternative waste stream projections to bound the characteristics of wastes likely to be encountered using arrival scenarios that potentially impact the commercial spent nuclear fuel (CSNF) waste stream. For TSPA-LA, this radionuclide inventory analysis considers U.S. Department of Energy (DOE) high-level radioactive waste (DHLW) glass and two types of spent nuclear fuel (SNF): CSNF and DOE-owned (DSNF). These wastes are placed in two groups of waste packages: the CSNF waste package and the codisposal waste package (CDSP), which are designated to contain DHLW glass and DSNF, or DHLW glass only. The radionuclide inventory for naval SNF is provided separately in the classified ''Naval Nuclear Propulsion Program Technical Support Document'' for the License Application. As noted previously, the radionuclide inventory data presented here is intended only for TSPA-LA postclosure calculations. It is not applicable to preclosure safety calculations. Safe storage, transportation, and ultimate disposal of these wastes require safety analyses to support the design and licensing of repository equipment and facilities. These analyses will require radionuclide inventories to represent the radioactive source term that must be accommodated during handling, storage and disposition of these wastes. This analysis uses the best available information to identify the radionuclide inventory that is expected at the last year of last emplacement

Development of a Solar System Concept Inventory

Science.gov (United States)

Hornstein, Seth D.; Duncan, D.; S, C. A. T.

2009-01-01

Concept inventories can provide useful insight into students’ understanding of key physical concepts. Knowing what your students have learned during a course is a valuable tool for improving your own teaching. Unfortunately, current astronomy concept inventories are not suitable for an introductory solar system course because they either cover too broad of a range of topics (e.g. Astronomy Diagnostic Test) or are too narrowly focused (e.g. Greenhouse Effect Concept Inventory, Lunar Phase Concept Inventory). We have developed the Solar System Concept Inventory (SSCI) to cover those topics commonly taught in an introductory solar system course. The topics included on the SSCI were selected by having faculty identify the key concepts they address when teaching about the solar system. SSCI topics include formation mechanisms, planetary interiors, atmospheric effects, and small solar system bodies. Student interviews were conducted to identify common naive ideas and reasoning difficulties relating to these key topics. Preliminary development of the SSCI was completed at the University of Colorado and involved over 400 students. A larger, national, multi-institutional field test is planned for Spring 2009 as a Collaboration of Astronomy Teaching Scholars (CATS) research project. We present here the results from the preliminary development and proposed changes for the next stage of research. We would like to thank the NSF for funding under Grant No. 0715517, a CCLI Phase III Grant for the Collaboration of Astronomy Teaching Scholars (CATS) Program.

Development of the Solar System Concept Inventory

Science.gov (United States)

Hornstein, S.; Prather, E.

2009-12-01

Concept inventories can provide useful insight into students’ understanding of key physical concepts. Knowing what your students have learned during a course is a valuable tool for improving your own teaching. Unfortunately, current astronomy concept inventories are not suitable for an introductory solar system course because they either cover too broad of a range of topics (e.g. Astronomy Diagnostic Test) or are too narrowly focused (e.g. Greenhouse Effect Concept Inventory, Lunar Phase Concept Inventory). We have developed the Solar System Concept Inventory (SSCI) to cover those topics commonly taught in an introductory solar system course. The topics included on the SSCI were selected by having faculty identify the key concepts they address when teaching about the solar system. SSCI topics include formation mechanisms, planetary interiors, atmospheric effects, and small solar system bodies. Student interviews were conducted to identify common naive ideas and reasoning difficulties relating to these key topics. The SSCI has been through two semesters of national, multi-institutional field-testing, involving over 1500 students. After the first semester of testing, question statistics were used to flag ineffective questions and flagged questions were revised or eliminated. We will present an overall outline of the SSCI development as well as our question-flagging criteria and question analyses from the latest round of field-testing. We would like to thank the NSF for funding under Grant No. 0715517, a CCLI Phase III Grant for the Collaboration of Astronomy Teaching Scholars (CATS) Program.

The Japanese Criminal Thinking Inventory: Development, Reliability, and Initial Validation of a New Scale for Assessing Criminal Thinking in a Japanese Offender Population.

Science.gov (United States)

Kishi, Kaori; Takeda, Fumi; Nagata, Yuko; Suzuki, Junko; Monma, Takafumi; Asanuma, Tohru

2015-11-01

Using a sample of 116 Japanese men who had been placed under parole/probationary supervision or released from prison, the present study examined standardization, reliability, and validation of the Japanese Criminal Thinking Inventory (JCTI) that was based on the short form of the Psychological Inventory of Criminal Thinking Styles (PICTS), a self-rating instrument designed to evaluate cognitive patterns specific to criminal conduct. An exploratory factor analysis revealed that four dimensions adequately captured the structure of the JCTI, and the resultant 17-item JCTI demonstrated high internal consistency. Compared with the Japanese version of the Buss-Perry Aggression Questionnaire (BAQ), the JCTI showed a favorable pattern of criterion-related validity. Prior criminal environment and drug abuse as the most recent offense also significantly correlated with the JCTI total score. Overall, the JCTI possesses an important implication for offender rehabilitation as it identifies relevant cognitive targets and assesses offender progress. © The Author(s) 2014.

Validation of Schema Coping Inventory and Schema Mode Inventory in Adolescents

NARCIS (Netherlands)

van Wijk-Herbrink, M.F.; Roelofs, J.; Broers, N.J.; Rijkeboer, M.M.; Arntz, A.; Bernstein, D.P.

2018-01-01

This study investigated whether the schema therapy constructs of schema coping and schema modes have validity in adolescents. We examined the validity and reliability of the Schema Coping Inventory (SCI) and an 80-item version of the Schema Mode Inventory (SMI) in a mixed sample of adolescents.

Influence of start up and pulsed operation on tritium release and inventory of NET ceramic blanket

International Nuclear Information System (INIS)

Iseli, M.; Esser, B.

1989-01-01

A first estimate for the tritium release behaviour of a ceramic breeder blanket in pulsed operation is obtained by assuming a linear steady state temperature distribution and taking into account the time constant of the thermal behaviour. The release behaviour of the breeder exposed to consecutive periods of tritium generation is described with an analytical solution of the diffusion equation. The results are compared with a simple exponential approach valid for surfacte desorption controlled release. The exponential model is used to simulate a blanket with aluminate as breeder material, which takes longest to reach steady state. The simulation demonstrates that a significant fraction (>67%) of steady state can be achieved after a testing time of about one day. (author). 7 refs.; 8 figs.; 3 tabs

Environmental Carcinogen Releases and Lung Cancer Mortality in Rural-Urban Areas of the United States

Science.gov (United States)

Luo, Juhua; Hendryx, Michael

2011-01-01

Purpose: Environmental hazards are unevenly distributed across communities and populations; however, little is known about the distribution of environmental carcinogenic pollutants and lung cancer risk across populations defined by race, sex, and rural-urban setting. Methods: We used the Toxics Release Inventory (TRI) database to conduct an…

Inventory of sites used to develop residual radioactivity criteria

International Nuclear Information System (INIS)

Ronca-Battista, M.; Hardeman, J.C. Jr.

1986-01-01

The US Environmental Protection Agency (EPA), in conjunction with the National Conference of Radiation Control Program Directors (CRCPD), has compiled an inventory of never licensed or otherwise poorly documented sites that may be contaminated with radioactive materials. This effort is in support of the EPA's development of radiation protection criteria for residual radioactivity at decommissioned sites. The inventory will help to establish the range of circumstances for which criteria are needed, as well as the suitability of candidate criteria for actual situations. The information will also be used to develop model sites and facilities for analyzing technical and economic feasibility of residual radioactivity criteria and to assess costs and benefits of alternate criteria. Relevant information about each site, such as radionuclides, waste forms, and quantities present will be included in the inventory when such information is available. The CRCPD has requested that each State radiation control agency furnish the information for the inventory. The inventory supplements the relatively extensive documentation of sites regulated by Federal or State agencies with information on old or unlicensed sites, such as old waste storage sites or radium ore processing facilities

On Inventory Control For Perishable Inventory Systems Subject To Uncertainties On Customer Demands

OpenAIRE

Abbou , Rosa; Loiseau , Jean-Jacques; Khaldi , Hajer; Farraa , Berna ,

2017-01-01

International audience; This paper deals with the inventory controller design for constrained production systems subject to uncertainties on the customer demands. The case study focuses on the inventory regulation problem in production systems where contain perishable finite products. Such systems are characterized by the presence of delays due to production processes, and constraints from the instantaneous inventory level, production level and the finite capacities of stocks. To do that, we ...

Belief in astrology inventory: development and validation.

Science.gov (United States)

Chico, Eliseo; Lorenzo-Seva, Urbano

2006-12-01

After the paper by Mayo, White, and Eysenck in 1978, a considerable number of papers studied the so-called sun-sign-effect predicted by astrology: people born with the sun in a positive sign are supposed to be extraverted, and those with the sun in a negative sign are supposed to be introverted. In these papers, researchers used ad hoc questionnaires with a few questions related to belief, knowledge, experience, or attitude toward astrology. However, an appropriate inventory with known psychometric properties has yet to be developed to assess the belief in astrology. In the present paper, the Belief in Astrology Inventory is presented with some psychometric data. The participants were 743 undergraduates studying Psychology and Social Sciences at a university in Spain. Correlation of scores on Belief in Astrology and Extraversion was small but significant (r = .22; r2 = .04) for positive sun-sign participants. This value accounts for negligible common variance. Women had significandy higher scores on the inventory than men.

The Factor Structure and Validity of the Persian Version of the Baumrind Parenting Style Inventory

Directory of Open Access Journals (Sweden)

اصغر مینائی

2017-06-01

Full Text Available In this study, the factor structure and validity of the Persian version of the Baumrind parenting style inventory were evaluated among 576 mothers of elementary school students in Tehran who had been selected through multistage cluster sampling method. This study is, due to its subject and purposes a descriptive study based on psychometric methods. The factor structure of the inventory was tested by AMOS software based on the fitting and modification indicators in the confirmatory factor analysis. The results showed that all items of the parenting style inventory except the items of 24, 8, 13, 18, assess the previously determined factors of the inventory, and that the inventory’s questions have a relatively good validity. Also, stratified alpha was used to calculate the reliability of the whole inventory, and Guttman coefficient was utilized to calculate the reliability of subscales. The outcomes indicated that the inventory and its subscales possess a relatively good reliability.

In-pile test of tritium release from tritium breeding materials (VOM-21H experiment)

International Nuclear Information System (INIS)

Kurasawa, Toshimasa; Takeshita, Hidefumi; Watanabe, Hitoshi; Yoshida, Hiroshi.

1986-10-01

Material development and blanket design of lithium-based ceramics such as lithium oxide, lithium aluminate, lithium silicate and lithium zirconate have been performed in Japan, United State of America and Europian Communities. Lithium oxide is a most attractive candidate for tritium breeding materials because of its high lithium density, high thermal conductivity and good tritium release performance. This work has been done to clarify the characteristics of tritium release and recovery from Li 2 O by means of in-situ tritium release measurement. The effects of temperature and sweep gas composition on the tritium release were investigated in this VOM-21H Experiment. Good measurement of tritium release was achieved but there were uncertainties in reproduciblity of data. The experimental results show that the role of surface adsorption/desorption makes a significant contribution to the tritium release and tritium inventory. Also, it is necessary to define the rate limiting process either diffusion or surface adsorption/desorption. (author)

Denmark's National Inventory Report 2010

DEFF Research Database (Denmark)

Nielsen, Ole-Kenneth; Lyck, Erik; Mikkelsen, Mette Hjorth

2010-01-01

This report is Denmark's National Inventory Report 2010. The report contains information on Denmark's emission inventories for all years' from 1990 to 2008 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2.......This report is Denmark's National Inventory Report 2010. The report contains information on Denmark's emission inventories for all years' from 1990 to 2008 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2....

Transuranic radionuclides in the Columbia River: sources, inventories, and geochemical behavior

International Nuclear Information System (INIS)

Beasley, T.M.

1987-01-01

The sources, inventories, and geochemical behavior of transuranic and other long-lived radionuclides in the lower Columbia River are summarized. Inventories have been estimated from the measured activities of the different radionuclides in 50 cores raised in 1977 and 1978, while annual export of transuranic radionuclides was determined from monthly water collections in the estuary. Continental shelf inventories of Pu and Am isotopes have been estimated using excess 210 Pb inventories and the mean 210 Pb//sup 239,240/Pu inventory ratio of 100 +/- 19 observed in representative cores raised from the shelf. Despite the substantial past addition of radioactivity to the river from operation of the plutonium production reactors at Hanford, the amounts of reactor-derived radionuclides in river sediments are small relative to fallout-derived nuclides. Erosional processes have mobilized both fallout-derived /sup 239,240/Pu and 137 Cs from the landscape to the river, but the quantities involved represent <1% of their fallout inventories within the river's drainage basin. 36 references, 6 figures, 2 tables

HHS Enterprise Data Inventory

Data.gov (United States)

U.S. Department of Health & Human Services — The Enterprise Data Inventory (EDI) is the comprehensive inventory listing of agency data resources including public, restricted public, and non-public datasets.

27 CFR 20.170 - Physical inventory.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Physical inventory. 20.170... Users of Specially Denatured Spirits Inventory and Records § 20.170 Physical inventory. Once in each... physical inventory of each formula of new and recovered specially denatured spirits. (Approved by the...

Inventory of radioactive waste disposals at sea

International Nuclear Information System (INIS)

1999-08-01

The IAEA was requested by the Contracting Parties to the Convention on the Prevention of Marine Pollution by Dumping of Wastes and Other Matter (London Convention 1972) to develop and maintain an inventory of radioactive material entering the marine environment from all sources. The rationale for having such an inventory is related to its use as an information base with which the impact of radionuclides from different sources entering the marine environment can be assessed and compared. To respond to the request of the London Convention, the IAEA has undertaken the development of the inventory to include: disposal at sea of radioactive wastes, and accidents and losses at sea involving radioactive materials. This report addresses disposal at sea of radioactive waste, a practice which continued from 1946 to 1993. It is a revision of IAEA-TECDOC-588, Inventory of Radioactive Material Entering the Marine Environment: Sea Disposal of Radioactive Waste, published in 1991. In addition to the data already published in IAEA-TECDOC-588, the present publication includes detailed official information on sea disposal operations carried out by the former Soviet Union and the Russian Federation provided in 1993 as well as additional information provided by Sweden in 1992 and the United Kingdom in 1997 and 1998

Compilation and evaluation of a Paso del Norte emission inventory

Energy Technology Data Exchange (ETDEWEB)

Funk, T.H.; Chinkin, L.R.; Roberts, P.T. [Sonoma Technology, Inc., 1360 Redwood Way, Suite C, 94954-1169 Petaluma, CA (United States); Saeger, M.; Mulligan, S. [Pacific Environmental Services, 5001 S. Miami Blvd., Suite 300, 27709 Research Triangle Park, NC (United States); Paramo Figueroa, V.H. [Instituto Nacional de Ecologia, Avenue Revolucion 1425, Nivel 10, Col. Tlacopac San Angel, Delegacion Alvaro Obregon, C.P., 01040, D.F. Mexico (Mexico); Yarbrough, J. [US Environmental Protection Agency - Region 6, 1445 Ross Avenue, Suite 1200, 75202-2733 Dallas, TX (United States)

2001-08-10

Emission inventories of ozone precursors are routinely used as input to comprehensive photochemical air quality models. Photochemical model performance and the development of effective control strategies rely on the accuracy and representativeness of an underlying emission inventory. This paper describes the tasks undertaken to compile and evaluate an ozone precursor emission inventory for the El Paso/Ciudad Juarez/Southern Dona Ana region. Point, area and mobile source emission data were obtained from local government agencies and were spatially and temporally allocated to a gridded domain using region-specific demographic and land-cover information. The inventory was then processed using the US Environmental Protection Agency (EPA) recommended Emissions Preprocessor System 2.0 (UAM-EPS 2.0) which generates emissions files compatible with the Urban Airshed Model (UAM). A top-down evaluation of the emission inventory was performed to examine how well the inventory represented ambient pollutant compositions. The top-down evaluation methodology employed in this study compares emission inventory ratios of non-methane hydrocarbon (NMHC)/nitrogen oxide (NO{sub x}) and carbon monoxide (CO)/NO{sub x} ratios to corresponding ambient ratios. Detailed NMHC species comparisons were made in order to investigate the relative composition of individual hydrocarbon species in the emission inventory and in the ambient data. The emission inventory compiled during this effort has since been used to model ozone in the Paso del Norte airshed (Emery et al., CAMx modeling of ozone and carbon monoxide in the Paso del Norte airshed. In: Proc of Ninety-Third Annual Meeting of Air and Waste Management Association, 18-22 June 2000, Air and Waste Management Association, Pittsburgh, PA, 2000)

Endogenous Business Cycle Dynamics within Metzlers Inventory Model: Adding an Inventory Floor.

Science.gov (United States)

Sushko, Irina; Wegener, Michael; Westerhoff, Frank; Zaklan, Georg

2009-04-01

Metzlers inventory model may produce dampened fluctuations in economic activity, thus contributing to our understanding of business cycle dynamics. For some parameter combinations, however, the model generates oscillations with increasing amplitude, implying that the inventory stock of firms eventually turns negative. Taking this observation into account, we reformulate Metzlers model by simply putting a floor to the inventory level. Within the new piecewise linear model, endogenous business cycle dynamics may now be triggered via a center bifurcation, i.e. for certain parameter combinations production changes are (quasi-)periodic.

Savannah River Plant's Accountability Inventory Management System (AIMS) (Nuclear materials inventory control)

International Nuclear Information System (INIS)

Croom, R.G.

1976-06-01

The Accountability Inventory Management System (AIMS) is a new computer inventory control system for nuclear materials at the Savannah River Plant, Aiken, South Carolina. The system has two major components, inventory files and system parameter files. AIMS, part of the overall safeguards program, maintains an up-to-date record of nuclear material by location, produces reports required by ERDA in addition to onplant reports, and is capable of a wide range of response to changing input/output requirements through use of user-prepared parameter cards, as opposed to basic system reprogramming

Is group A thawed plasma suitable as the first option for emergency release transfusion? (CME).

Science.gov (United States)

Chhibber, Vishesh; Greene, Mindy; Vauthrin, Michelle; Bailey, Jeff; Weinstein, Robert

2014-07-01

Group AB plasma, which lacks anti-A and anti-B isohemagglutinins, is issued for emergency transfusion when a patient's ABO group is unknown, but the relative scarcity of group AB blood donors limits its availability. We sought to establish a thawed plasma inventory to improve the rapid availability of plasma in the emergency release setting but were concerned about potential wastage of group AB plasma. Recognizing that plasma-incompatible apheresis platelets are routinely transfused and only rarely result in hemolytic reactions if the donor is blood group O, and considering that group A plasma would be compatible with approximately 85% of our patient population, we instituted an emergency release policy whereby thawed group A plasma is issued to all patients of unknown blood group or if compatible plasma is not available. ABO-compatible plasma is then issued, if needed, once the patient's blood group is determined. We prospectively assessed the outcomes of all patients who received incompatible plasma under our policy. During the first 5 years under this policy, 385 emergency release requests for plasma were received by our blood bank. Among them, 23 group B or AB patients met criteria for receiving a median of 2 units of incompatible group A plasma. No hemolytic transfusion reactions or other adverse events related to transfusion were seen in any of these 23 patients. We propose that group A plasma may be an acceptable alternative to AB plasma as the first option in the emergency release setting. © 2014 AABB.

Epidemiology of Infectious Disease-Related Death After Release from Prison, Washington State, United States, and Queensland, Australia: A Cohort Study.

Science.gov (United States)

Binswanger, Ingrid A; Blatchford, Patrick J; Forsyth, Simon J; Stern, Marc F; Kinner, Stuart A

2016-01-01

People in prison may be at high risk for infectious diseases and have an elevated risk of death immediately after release compared with later; their risk of death is elevated for at least a decade after release. We compared rates, characteristics, and prison-related risk factors for infectious disease-related mortality among people released from prisons in Queensland, Australia, and Washington State, United States, regions with analogous available data. We analyzed data from retrospective cohort studies of people released from prison in Queensland (1997-2007, n=37,180) and Washington State (1999-2009, n=76,208) and linked identifiers from each cohort to its respective national death index. We estimated infectious disease-related mortality rates (deaths per person-years in community) and examined associations using Cox proportional hazard models. The most frequent infectious disease-related underlying cause of death after release from prison was pneumonia (43%, 23/54 deaths) in the Australian cohort and viral hepatitis (40%, 69/171 deaths) in the U.S. cohort. The infectious disease-related mortality rate was significantly higher in the U.S. cohort than in the Australian cohort (51.2 vs. 26.5 deaths per 100,000 person-years; incidence rate ratio = 1.93, 95% confidence interval 1.42, 2.62). In both cohorts, increasing age was strongly associated with mortality from infectious diseases. Differences in the epidemiology of infectious disease-related mortality among people released from prison may reflect differences in patterns of community health service delivery in each region. These findings highlight the importance of preventing and treating hepatitis C and other infectious diseases during the transition from prison to the community.

Radioactive material inventory control at a waste characterization facility

International Nuclear Information System (INIS)

Yong, L.K.; Chapman, J.A.; Schultz, F.J.

1996-01-01

Due to the recent introduction of more stringent Department of Energy (DOE) regulations and requirements pertaining to nuclear and criticality safety, the control of radioactive material inventory has emerged as an important facet of operations at DOE nuclear facilities. In order to comply with nuclear safety regulations and nuclear criticality requirements, radioactive material inventories at each nuclear facility have to be maintained below limits specified for the facility in its safety authorization basis documentation. Exceeding these radioactive material limits constitutes a breach of the facility's nuclear and criticality safety envelope and could potentially result in an accident, cause a shut-down of the facility, and bring about imminent regulatory repercussions. The practice of maintaining control of radioactive material, especially sealed and unsealed sources, is commonplace and widely implemented; however, the requirement to track the entire radioactivity inventory at each nuclear facility for the purpose of ensuring nuclear safety is a new development. To meet the new requirements, the Applied Radiation Measurements Department at Oak Ridge National Laboratory (ORNL) has developed an information system, called the open-quotes Radioactive Material Inventory Systemclose quotes (RMIS), to track the radioactive material inventory at an ORNL facility, the Waste Examination and Assay Facility (WEAF). The operations at WEAF, which revolve around the nondestructive assay and nondestructive examination of waste and related research and development activities, results in an ever-changing radioactive material inventory. Waste packages and radioactive sources are constantly being brought in or taken out of the facility; hence, use of the RMIS is necessary to ensure that the radioactive material inventory limits are not exceeded

Pricing, Variety, and Inventory Decisions in Retail Operations Management

OpenAIRE

Maddah, Bacel

2005-01-01

This dissertation is concerned with decision making in retail operations management. Specifically, we focus on pricing, variety, and inventory decisions, which are at the interface of the marketing and operations functions of a retail firm. We consider two problems that relate to two major types of retail goods. First, we study joint pricing, variety, and inventory decisions for a set of substitutable" items that serve the same need for the consumer (commonly referred to as a "retailer's ...

27 CFR 40.523 - Inventories.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Inventories. 40.523... PROCESSED TOBACCO Manufacture of Processed Tobacco Operations by Manufacturers of Processed Tobacco § 40.523 Inventories. Every manufacturer of processed tobacco must provide a true and accurate inventory on TTB F 5210...

Quality manual for the Danish greenhouse gas inventory. Version 2

Energy Technology Data Exchange (ETDEWEB)

Nielsen, O.-K.; Plejdrup, M.S.; Winther, M. [and others

2013-02-15

This report outlines the quality work undertaken by the emission inventory group at the Department of Environmental Science, Aarhus University in connection with the preparation and reporting of the Danish greenhouse gas inventory. This report updates and expands on the first version of the quality manual published in 2005. The report fulfils the mandatory requirements for a quality assurance/quality control (QA/QC) plan as lined out in the UNFCCC reporting guidelines and the specifications related to reporting under the Kyoto Protocol. The report describes all elements of the internal QC procedures as well as the QA and verification activities carried out in connection with the Danish greenhouse gas inventory. (Author)

Hydrogen inventory in gallium

International Nuclear Information System (INIS)

Mazayev, S.N.; Prokofiev, Yu.G.

1994-01-01

Investigations of hydrogen inventory in gallium (99.9%) were carried out after saturation both from molecular phase and from glow discharge plasma at room temperature, 370 and 520 K. Saturation took place during 3000 s under hydrogen pressure of 20 Pa, and ion flux was about 1x10 15 ions/cm 2 s with an energy about 400 eV during discharge. Hydrogen concentration in Ga at room temperature and that for 370 K by the saturation from gaseous phase was (2-3)x10 14 cm -3 Pa -1/2 . Hydrogen concentration at temperature 520 K increased by five times. Inventory at room temperature for irradiation from discharge was 7x10 16 cm -3 at the dose about 3x10 18 ions/cm 2 . It was more than inventory at temperature 520 K by four times and more than maximum inventory from gaseous phase at 520 K by a factor of 10. Inventory increased when temperature decreased. Diffusion coefficient D=0.003 exp(-2300/RT) cm 2 /s, was estimated from temperature dependence. ((orig.))

Nuclear materials inventory plan

International Nuclear Information System (INIS)

Doerr, R.W.; Nichols, D.H.

1982-03-01

In any processing, manufacturing, or active storage facility it is impractical to assume that any physical security system can prevent the diversion of Special Nuclear Material (SNM). It is, therefore, the responsibility of any DOE Contractor, Licensee, or other holder of SNM to provide assurance that loss or diversion of a significant quantity of SNM is detectable. This ability to detect must be accomplishable within a reasonable time interval and can be accomplished only by taking physical inventories. The information gained and decisions resulting from these inventories can be no better than the SNM accounting system and the quality of measurements performed for each receipt, removal and inventory. Inventories interrupt processing or production operations, increase personnel exposures, and can add significantly to the cost of any operation. Therefore, realistic goals for the inventory must be defined and the relationship of the inherent parameters used in its validation be determined. Purpose of this document is to provide a statement of goals and a plan of action to achieve them

Denmark's National Inventory Report 2014

DEFF Research Database (Denmark)

Nielsen, Ole-Kenneth; Plejdrup, Marlene Schmidt; Winther, Morten

This report is Denmark’s National Inventory Report 2014. The report contains information on Denmark’s emission inventories for all years’ from 1990 to 2012 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2......This report is Denmark’s National Inventory Report 2014. The report contains information on Denmark’s emission inventories for all years’ from 1990 to 2012 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2...

Denmark's National Inventory Report 2013

DEFF Research Database (Denmark)

Nielsen, Ole-Kenneth; Plejdrup, Marlene Schmidt; Winther, Morten

This report is Denmark’s National Inventory Report 2013. The report contains information on Denmark’s emission inventories for all years’ from 1990 to 2011 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2.......This report is Denmark’s National Inventory Report 2013. The report contains information on Denmark’s emission inventories for all years’ from 1990 to 2011 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2....

Denmark's National Inventory Report 2017

DEFF Research Database (Denmark)

Nielsen, Ole-Kenneth; Plejdrup, Marlene Schmidt; Winther, Morten

This report is Denmark’s National Inventory Report 2017. The report contains information on Denmark’s emission inventories for all years’ from 1990 to 2015 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2......This report is Denmark’s National Inventory Report 2017. The report contains information on Denmark’s emission inventories for all years’ from 1990 to 2015 for CO2, CH4, N2O, HFCs, PFCs and SF6, NOx, CO, NMVOC, SO2...

Six ways to reduce inventory.

Science.gov (United States)

Lunn, T

1996-05-01

The purpose of this presentation is to help you reduce the inventory in your operation. We will accomplish that task by discussing six specific methods that companies have used successfully to reduce their inventory. One common attribute of these successes is that they also build teamwork among the people. Every business operation today is concerned with methods to improve customer service. The real trick is to accomplish that task without increasing inventory. We are all concerned with improving our skills at keeping inventory low.

ANALYSIS MODEL FOR INVENTORY MANAGEMENT

Directory of Open Access Journals (Sweden)

CAMELIA BURJA

2010-01-01

Full Text Available The inventory represents an essential component for the assets of the enterprise and the economic analysis gives them special importance because their accurate management determines the achievement of the activity object and the financial results. The efficient management of inventory requires ensuring an optimum level for them, which will guarantee the normal functioning of the activity with minimum inventory expenses and funds which are immobilised. The paper presents an analysis model for inventory management based on their rotation speed and the correlation with the sales volume illustrated in an adequate study. The highlighting of the influence factors on the efficient inventory management ensures the useful information needed to justify managerial decisions, which will lead to a balancedfinancial position and to increased company performance.

Evaluating Indicators and Life Cycle Inventories for Processes in Early Stages of Technical Readiness

Energy Technology Data Exchange (ETDEWEB)

Tan, Eric C [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Smith, Raymond [U.S. Environmental Protection Agency (EPA); Ruiz-Mercado, Gerardo [U.S. Environmental Protection Agency (EPA)

2017-11-01

This presentation examines different methods for analyzing manufacturing processes in the early stages of technical readiness. Before developers know much detail about their processes, it is valuable to apply various assessments to evaluate their performance. One type of assessment evaluates performance indicators to describe how closely processes approach desirable objectives. Another type of assessment determines the life cycle inventories (LCI) of inputs and outputs for processes, where for a functional unit of product, the user evaluates the resources used and the releases to the environment. These results can be compared to similar processes or combined with the LCI of other processes to examine up-and down-stream chemicals. The inventory also provides a listing of the up-stream chemicals, which permits study of the whole life cycle. Performance indicators are evaluated in this presentation with the U.S. Environmental Protection Agency's GREENSCOPE (Gauging Reaction Effectiveness for ENvironmental Sustainability with a multi-Objective Process Evaluator) methodology, which evaluates processes in four areas: Environment, Energy, Economics, and Efficiency. The method develops relative scores for indicators that allow comparisons across various technologies. In this contribution, two conversion pathways for producing cellulosic ethanol from biomass, via thermochemical and biochemical routes, are studied. The information developed from the indicators and LCI can be used to inform the process design and the potential life cycle effects of up- and down-stream chemicals.

The integrated control of production-inventory systems

NARCIS (Netherlands)

Nyen, van P.L.M.

2005-01-01

In this thesis, we investigate a multi-product, multi-machine production-inventory (PI) system that is characterized by: ?? relatively high and stable demand; ?? uncertainty in the precise timing of demand; ?? variability in the production process; ?? job shop routings; ?? considerable setup times

National Wetlands Inventory Polygons

Data.gov (United States)

Minnesota Department of Natural Resources — Wetland area features mapped as part of the National Wetlands Inventory (NWI). The National Wetlands Inventory is a national program sponsored by the US Fish and...

The HOME Inventory and Family Demographics.

Science.gov (United States)

Bradley, Robert H.; Caldwell, Bettye M.

1984-01-01

Examines the relation between the Home Observation for Measurement of Environment (HOME) Inventory and sex, race, socioeconomic status, the amount of crowding in the home, and birth order. Performs multivariate analysis of covariance on an intact family sample using HOME subscales as criterion measures and status and structural variables as…

Automatic Estimation of the Radiological Inventory for the Dismantling of Nuclear Facilities

International Nuclear Information System (INIS)

Garcia-Bermejo, R.; Felipe, A.; Gutierrez, S.; Salas, E.; Martin, N.

2008-01-01

The estimation of the radiological inventory of Nuclear Facilities to be dismantled is a process that included information related with the physical inventory of all the plant and radiological survey. Estimation of the radiological inventory for all the components and civil structure of the plant could be obtained with mathematical models with statistical approach. A computer application has been developed in order to obtain the radiological inventory in an automatic way. Results: A computer application that is able to estimate the radiological inventory from the radiological measurements or the characterization program has been developed. In this computer applications has been included the statistical functions needed for the estimation of the central tendency and variability, e.g. mean, median, variance, confidence intervals, variance coefficients, etc. This computer application is a necessary tool in order to be able to estimate the radiological inventory of a nuclear facility and it is a powerful tool for decision taken in future sampling surveys

Construct Validation of the Physics Metacognition Inventory

Science.gov (United States)

Taasoobshirazi, Gita; Farley, John

2013-02-01

The 24-item Physics Metacognition Inventory was developed to measure physics students' metacognition for problem solving. Items were classified into eight subcomponents subsumed under two broader components: knowledge of cognition and regulation of cognition. The students' scores on the inventory were found to be reliable and related to students' physics motivation and physics grade. An exploratory factor analysis provided evidence of construct validity, revealing six components of students' metacognition when solving physics problems including: knowledge of cognition, planning, monitoring, evaluation, debugging, and information management. Although women and men differed on the components, they had equivalent overall metacognition for problem solving. The implications of these findings for future research are discussed.

10 CFR 39.37 - Physical inventory.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Physical inventory. 39.37 Section 39.37 Energy NUCLEAR... inventory. Each licensee shall conduct a semi-annual physical inventory to account for all licensed material received and possessed under the license. The licensee shall retain records of the inventory for 3 years...

Base-age invariance and inventory projections

Science.gov (United States)

C. J. Cieszewski; R. L. Bailey; B. E. Borders; G. H. Brister; B. D. Shiver

2000-01-01

One of the most important functions of forest inventory is to facilitate management decisions towards forest sustainability based on inventory projections into the future. Therefore, most forest inventories are used for predicting future states of the forests, in modern forestry the most common methods used in inventory projections are based on implicit functions...

Licensed fuel facility status report. Inventory difference data, January-June 1982

International Nuclear Information System (INIS)

1983-02-01

NRC is committed to the periodic publication of licensed fuel facilities inventory difference data, following agency review of the information and completion of any related investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233

SUBDOSA: a computer program for calculating external doses from accidental atmospheric releases of radionuclides

International Nuclear Information System (INIS)

Strenge, D.L.; Watson, E.C.; Houston, J.R.

1975-06-01

A computer program, SUBDOSA, was developed for calculating external γ and β doses to individuals from the accidental release of radionuclides to the atmosphere. Characteristics of SUBDOSA are: doses from both γ and β radiation are calculated as a function of depth in tissue, summed and reported as skin, eye, gonadal, and total body dose; doses are calculated for releases within each of several release time intervals and nuclide inventories and atmospheric dispersion conditions are considered for each time interval; radioactive decay is considered during the release and/or transit using a chain decay scheme with branching to account for transitions to and from isomeric states; the dose from gamma radiation is calculated using a numerical integration technique to account for the finite size of the plume; and the program computes and lists the normalized air concentrations at ground level as a function of distance from the point of release. (auth)

Historical releases of radioactivity to the environment from ORNL

International Nuclear Information System (INIS)

Ohnesorge, W.F.

1986-05-01

This report gives a brief history and assessment of ORNL radionuclide releases to the environment. A short history and an inventory of radioactivity disposed of by shallow land burial and hydrofracture techniques are given along with a brief discussion of the potential environmental impact of these disposed materials. The data available for this report varied greatly in quality. Data on contaminated liquid waste and liquids discharged to the environment are much more reliable than early data on contaminated air discharges and contaminated solid waste. Data for more recent years are more complete and reliable than data obtained from records dating back to the early history of the laboratory. The data presented here do not include materials retrievably stored (with the exception of uranium solid waste data) or inventories of materials stored in operating or surplus facilities since these materials presently have no contact with or loss to the environment

The Spatial Release of Cognitive Load in Cocktail Party Is Determined by the Relative Levels of the Talkers.

Science.gov (United States)

Andéol, Guillaume; Suied, Clara; Scannella, Sébastien; Dehais, Frédéric

2017-06-01

In a multi-talker situation, spatial separation between talkers reduces cognitive processing load: this is the "spatial release of cognitive load". The present study investigated the role played by the relative levels of the talkers on this spatial release of cognitive load. During the experiment, participants had to report the speech emitted by a target talker in the presence of a concurrent masker talker. The spatial separation (0° and 120° angular distance in azimuth) and the relative levels of the talkers (adverse, intermediate, and favorable target-to-masker ratio) were manipulated. The cognitive load was assessed with a prefrontal functional near-infrared spectroscopy. Data from 14 young normal-hearing listeners revealed that the target-to-masker ratio had a direct impact on the spatial release of cognitive load. Spatial separation significantly reduced the prefrontal activity only for the intermediate target-to-masker ratio and had no effect on prefrontal activity for the favorable and the adverse target-to-masker ratios. Therefore, the relative levels of the talkers might be a key point to determine the spatial release of cognitive load and more specifically the prefrontal activity induced by spatial cues in multi-talker situations.

Annual Danish emissions inventory report to UNECE. Inventory 1990 - 2002

Energy Technology Data Exchange (ETDEWEB)

Illerup, J B; Nielsen, M; Winther, M; Hjort Mikkelsen, M; Lyck, E; Hoffmann, L; Fauser, P

2004-05-01

This report is a documentation report on the emission inventories for Denmark as reported to the UNECE Secretariat under the Convention on Long Range Transboundary Air Pollution due by 15 February 2004. The report contains information on Denmark's emission inventories regarding emissions of (1) SOx for the years 1980-2002, (2) NOx, CO, NMVOC and NH{sub 3} for the years 1985-2002; (3) Particulate matter: TSP, PM10, PM2.5 for the years 2000-2002, (4) Heavy Metals: Pb, Cd, Hg, As, Cr, Cu, Ni, Se and Zn for the years 1990-2002, and (5) Polyaromatic hydrocarbons (PAH): Benzo(a)pyrene, benzo(b)fluoranthene, benzo(k)fluoranthene and indeno(1,2,3-cd)pyrene for the years 1990-2002. Furthermore, the report contains information on background data for emissions inventory. (au)

Annual Danish emissions inventory report to UNECE. Inventory 1990 - 2002

Energy Technology Data Exchange (ETDEWEB)

Illerup, J.B.; Nielsen, M.; Winther, M.; Hjort Mikkelsen, M.; Lyck, E.; Hoffmann, L.; Fauser, P.

2004-05-01

This report is a documentation report on the emission inventories for Denmark as reported to the UNECE Secretariat under the Convention on Long Range Transboundary Air Pollution due by 15 February 2004. The report contains information on Denmark's emission inventories regarding emissions of (1) SOx for the years 1980-2002, (2) NOx, CO, NMVOC and NH{sub 3} for the years 1985-2002; (3) Particulate matter: TSP, PM10, PM2.5 for the years 2000-2002, (4) Heavy Metals: Pb, Cd, Hg, As, Cr, Cu, Ni, Se and Zn for the years 1990-2002, and (5) Polyaromatic hydrocarbons (PAH): Benzo(a)pyrene, benzo(b)fluoranthene, benzo(k)fluoranthene and indeno(1,2,3-cd)pyrene for the years 1990-2002. Furthermore, the report contains information on background data for emissions inventory. (au)

Recent evidence on the muted inventory cycle

OpenAIRE

Andrew J. Filardo

1995-01-01

Inventories play an important role in business cycles. Inventory build-ups add momentum to the economy during expansions, while inventory liquidations sap economic strength during recessions. In addition, because inventory fluctuations are notoriously difficult to predict, they present considerable uncertainty in assessing the economic outlook.> The role of inventories in shaping the current outlook for the U.S. economy is particularly uncertain. In the early 1990s, inventory swings appeared ...

Integrated inventory information system

Digital Repository Service at National Institute of Oceanography (India)

Sarupria, J.S.; Kunte, P.D.

The nature of oceanographic data and the management of inventory level information are described in Integrated Inventory Information System (IIIS). It is shown how a ROSCOPO (report on observations/samples collected during oceanographic programme...

30 CFR 220.032 - Inventories.

Science.gov (United States)

2010-07-01

... operations. The accumulation of surplus stocks shall be avoided by proper materiel control, inventory and... physical inventory that has not been credited to NPSL operations under § 220.015(a)(2) shall be credited to... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Inventories. 220.032 Section 220.032 Mineral...

Nanotechnology in the real world: Redeveloping the nanomaterial consumer products inventory

Directory of Open Access Journals (Sweden)

Marina E. Vance

2015-08-01

Full Text Available To document the marketing and distribution of nano-enabled products into the commercial marketplace, the Woodrow Wilson International Center for Scholars and the Project on Emerging Nanotechnologies created the Nanotechnology Consumer Products Inventory (CPI in 2005. The objective of this present work is to redevelop the CPI by leading a research effort to increase the usefulness and reliability of this inventory. We created eight new descriptors for consumer products, including information pertaining to the nanomaterials contained in each product. The project was motivated by the recognition that a diverse group of stakeholders from academia, industry, and state/federal government had become highly dependent on the inventory as an important resource and bellweather of the pervasiveness of nanotechnology in society. We interviewed 68 nanotechnology experts to assess key information needs. Their answers guided inventory modifications by providing a clear conceptual framework best suited for user expectations. The revised inventory was released in October 2013. It currently lists 1814 consumer products from 622 companies in 32 countries. The Health and Fitness category contains the most products (762, or 42% of the total. Silver is the most frequently used nanomaterial (435 products, or 24%; however, 49% of the products (889 included in the CPI do not provide the composition of the nanomaterial used in them. About 29% of the CPI (528 products contain nanomaterials suspended in a variety of liquid media and dermal contact is the most likely exposure scenario from their use. The majority (1288 products, or 71% of the products do not present enough supporting information to corroborate the claim that nanomaterials are used. The modified CPI has enabled crowdsourcing capabilities, which allow users to suggest edits to any entry and permits researchers to upload new findings ranging from human and environmental exposure data to complete life cycle

A new approach for peat inventory methods; Turvetutkimusten menetelmaekehitystarkastelu

Energy Technology Data Exchange (ETDEWEB)

Laatikainen, M.; Leino, J.; Lerssi, J.; Torppa, J.; Turunen, J. Email: jukka.turunen@gtk.fi

2011-07-01

Development of the new peatland inventory method started in 2009. There was a need to investigate whether new methods and tools could be developed cost-effectively so field inventory work would more completely cover the whole peatland area and the quality and liability of the final results would remain at a high level. The old inventory method in place at the Geological Survey of Finland (GTK) is based on the main transect and cross transect approach across a peatland area. The goal of this study was to find a practical grid-based method linked to the geographic information system suitable for field conditions. the triangle-grid method with even distance between the study points was found to be the most suitable approach. A new Ramac-ground penetrating radar was obtained by the GTK in 2009, and it was concluded in the study of new peatland inventory methods. This radar model is relatively light and very suitable, for example, to the forestry drained peatlands, which are often difficult to cross because of the intensive ditch network. the goal was to investigate the best working methods for the ground penetrating radar to optimize its use in the large-scale peatland inventory. Together with the new field inventory methods, a novel interpolation-based method (MITTI) for modelling peat depths was developed. MITTI makes it possible to take advantage of all the available peat-depth data including, at the moment, aerogeophysical and ground penetrating radar measurements, drilling data and the mire outline. The characteristic uncertainties of each data type are taken into account and, in addition to the depth model itself, an uncertainty map of the model is computed. Combined with the grid-based field inventory method, this multi-approach provides better tools to more accurately estimate the peat depths, peat amounts and peat type distributions. The development of the new peatland inventory method was divided into four separate sections: (1) Development of new field

Databases for highway inventories. Proposal for a new model

Energy Technology Data Exchange (ETDEWEB)

Perez Casan, J.A.

2016-07-01

Database models for highway inventories are based on classical schemes for relational databases: many related tables, in which the database designer establishes, a priori, every detail that they consider relevant for inventory management. This kind of database presents several problems. First, adapting the model and its applications when new database features appear is difficult. In addition, the different needs of different sets of road inventory users are difficult to fulfil with these schemes. For example, maintenance management services, road authorities and emergency services have different needs. In addition, this kind of database cannot be adapted to new scenarios, such as other countries and regions (that may classify roads or name certain elements differently). The problem is more complex if the language used in these scenarios is not the same as that used in the database design. In addition, technicians need a long time to learn to use the database efficiently. This paper proposes a flexible, multilanguage and multipurpose database model, which gives an effective and simple solution to the aforementioned problems. (Author)

Science Inventory | US EPA

Science.gov (United States)

The Science Inventory is a searchable database of research products primarily from EPA's Office of Research and Development. Science Inventory records provide descriptions of the product, contact information, and links to available printed material or websites.

Linear free energy correlations for fission product release from the Fukushima-Daiichi nuclear accident.

Science.gov (United States)

Abrecht, David G; Schwantes, Jon M

2015-03-03

This paper extends the preliminary linear free energy correlations for radionuclide release performed by Schwantes et al., following the Fukushima-Daiichi Nuclear Power Plant accident. Through evaluations of the molar fractionations of radionuclides deposited in the soil relative to modeled radionuclide inventories, we confirm the initial source of the radionuclides to the environment to be from active reactors rather than the spent fuel pool. Linear correlations of the form In χ = −α ((ΔGrxn°(TC))/(RTC)) + β were obtained between the deposited concentrations, and the reduction potentials of the fission product oxide species using multiple reduction schemes to calculate ΔG°rxn (TC). These models allowed an estimate of the upper bound for the reactor temperatures of TC between 2015 and 2060 K, providing insight into the limiting factors to vaporization and release of fission products during the reactor accident. Estimates of the release of medium-lived fission products 90Sr, 121mSn, 147Pm, 144Ce, 152Eu, 154Eu, 155Eu, and 151Sm through atmospheric venting during the first month following the accident were obtained, indicating that large quantities of 90Sr and radioactive lanthanides were likely to remain in the damaged reactor cores.

NPS National Transit Inventory and Performance Report, 2016

Science.gov (United States)

2017-12-01

This document summarizes key highlights and performance measures relating to the National Park Service (NPS) 2016 National Transit Inventory, by presenting data for NPS transit systems and vehicles nationwide. These highlights and performance measure...

Comparison and analysis of release scenarios for ground disposal of various nations

International Nuclear Information System (INIS)

Sakata, Sadahiro; Nakai, Kunihiro

1985-01-01

This report is aimed at comparing and analyzing the concept and evaluation methods of varuous foreign countries concerning their release scenarios for ground disposal of low- and high-level radioactive wastes in order to provide helpful information to be used in developing release scenarios for Japan. The groundwater release scenario and human intrusion scenario should particularly be well examined in considering shallow ground disposal of low-level wastes. Assessment of the leaching rate is important for a groundwater release scenario. Experimental data and verification tests are required to support the simplified model to be used for safety assessment. Evaluation of the radioactive nucleide inventory is also important for ground disposal of low-level wastes. An evaluation system should be established as soon as possible. For ground disposal of high-level radioactive wastes, on the other hand, it will become increasingly important to establish performance assessment models for practical evaluation of the rate of release from the engineered barrier and to collect test and verification data for suporting them. (Nogami, K.)

42 CFR 35.41 - Inventory.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Inventory. 35.41 Section 35.41 Public Health PUBLIC... STATION MANAGEMENT Disposal of Money and Effects of Deceased Patients § 35.41 Inventory. Promptly after the death of a patient in a station or hospital of the Service, an inventory of his money and effects...

Petroleum and hazardous material releases from industrial facilities associated with Hurricane Katrina.

Science.gov (United States)

Santella, Nicholas; Steinberg, Laura J; Sengul, Hatice

2010-04-01

Hurricane Katrina struck an area dense with industry, causing numerous releases of petroleum and hazardous materials. This study integrates information from a number of sources to describe the frequency, causes, and effects of these releases in order to inform analysis of risk from future hurricanes. Over 200 onshore releases of hazardous chemicals, petroleum, or natural gas were reported. Storm surge was responsible for the majority of petroleum releases and failure of storage tanks was the most common mechanism of release. Of the smaller number of hazardous chemical releases reported, many were associated with flaring from plant startup, shutdown, or process upset. In areas impacted by storm surge, 10% of the facilities within the Risk Management Plan (RMP) and Toxic Release Inventory (TRI) databases and 28% of SIC 1311 facilities experienced accidental releases. In areas subject only to hurricane strength winds, a lower fraction (1% of RMP and TRI and 10% of SIC 1311 facilities) experienced a release while 1% of all facility types reported a release in areas that experienced tropical storm strength winds. Of industrial facilities surveyed, more experienced indirect disruptions such as displacement of workers, loss of electricity and communication systems, and difficulty acquiring supplies and contractors for operations or reconstruction (55%), than experienced releases. To reduce the risk of hazardous material releases and speed the return to normal operations under these difficult conditions, greater attention should be devoted to risk-based facility design and improved prevention and response planning.

Assessment of drought related mortality in pinyon-juniper and ponderosa pine forests using Forest Inventory and Analysis data

Science.gov (United States)

John D. Shaw

2008-01-01

(Please note, this is an abstract only) Widespread mortality in several forest types is associated with several years of drought in the Southwest. Implementation of USDA Forest Service Forest Inventory and Analysis (FIA) annual inventory in several states coincided with the onset of elevated mortality rates. Analysis of data collected 2000-2004 reveals the status and...

The Carnism Inventory: Measuring the ideology of eating animals.

Science.gov (United States)

Monteiro, Christopher A; Pfeiler, Tamara M; Patterson, Marcus D; Milburn, Michael A

2017-06-01

Beliefs surrounding the practice of eating animals are widely held, and have been argued to constitute an ideology named carnism (Joy, 2009). We developed and validated the novel Carnism Inventory to measure two positively related components of carnistic beliefs: carnistic defense and carnistic domination. We anticipated that carnistic defense would legitimate the practice of eating animals, while carnistic domination would support the killing of animals for their meat. The Carnism Inventory showed the hypothesized two-dimensional structure as well as good internal consistencies and stability (N = 302, Study 1). We also demonstrated the convergent and discriminant validity of the Carnism Inventory (N = 781, Study 2a). As expected, carnistic defense predicted meat consumption, while carnistic domination was a significant predictor of having slaughtered an animal (N = 478, Study 2b). Both scales were significantly related to sociopolitical beliefs, including right-wing authoritarianism and social dominance orientation, but only carnistic domination was related to symbolic racism and sexism (N = 373, Study 3). Taken together, our findings highlight the utility of the two-dimensional conceptualization and measurement of carnistic beliefs and offer new insights into one of the most common human behaviors: Eating animals is not only a gustatory behavior, as widely believed, but also an ideological one. Copyright © 2017 Elsevier Ltd. All rights reserved.

New mechanism for enhancing ash removal efficiency and reducing tritium inventory

International Nuclear Information System (INIS)

Li Chengyue; Deng Baiquan; Yan Jiancheng

2007-01-01

A new mechanism is suggested to suppress ash particle back streams in the divertor region of our fusion experimental breeder (FEB) reactor for enhancing the ash removal efficiency and reducing the tritium inventory by applications of the nonlinear effect of high power rf ponderomotive force potential which reflects the plate-released and re-ionized He + back to the plate. Meanwhile, the potential does not hinder α particles, which are coming from scraping of the layer, flowing to the target plate. However, it does stop tritium ions flowing to the target. Based on the FEB design parameters, our calculations have shown that the ash removal efficiency can be improved by as much as 40% if the parallel component of rf field 150-200 V/cm is applied to the location at a perpendicular distance L=20 cm apart from the plate and the plate-recycling neutral helium atom energy is about 0.75 eV, at the same time, the tritium inventory can be reduced to some extent. (authors)

Blood inventory management: hospital best practice.

Science.gov (United States)

Stanger, Sebastian H W; Yates, Nicola; Wilding, Richard; Cotton, Sue

2012-04-01

Blood is a perishable product, and hence good management of inventories is crucial. Blood inventory management is a trade-off between shortage and wastage. The challenge is to keep enough stock to ensure a 100% supply of blood while keeping time expiry losses at a minimum. This article focuses on inventory management of red blood cells in hospital transfusion laboratories to derive principles of best practice and makes recommendations that will ensure losses due to time expiry are kept to a minimum. The literature was reviewed to identify available models for perishable inventory management. Historical data from the UK blood supply chain was analyzed to identify hospitals with good inventory management practice and low wastage levels. Transfusion laboratory managers in the selected hospitals were interviewed in 7 case studies with the aim of identifying drivers for low wastage and good inventory management practice. The findings from the case studies were compared with the literature. The extant literature asserts that the drivers for good inventory performance are the use of complex inventory models and algorithms. This study has found this not to be the case. Instead, good performance is driven by the quality of transfusion laboratory staff, who must be skilled, regularly trained, and experienced. Electronic crossmatching, transparency of the inventory, and simple management procedures also facilitate good performance. Copyright © 2012 Elsevier Inc. All rights reserved.

Thermal effect of periodical bakeout on tritium inventory in first wall and permeation to coolant in reactor life

International Nuclear Information System (INIS)

Nakahara, Katsuhiko

1989-01-01

In view of safety, it is very important to control the tritium inventory in first walls and permeation to the coolant. A time-dependent diffusion and temperature calculation code, TPERM, was developed. Using this code, a numerical study on the long term effects of the bakeout temperature on tritium inventory and tritium permeation to the coolant was made. In this study, an FER type first wall (stainless steel) was considered and a cyclic operation (one cycle includes a plasma burn phase and a bakeout phase) was assumed. The results are as follows: (i) There is almost no difference in the tritium inventory in the first wall between the operation with 150 0 C-bakeout and the continuous burning operation (without bakeout). In both cases there is not tritium permeation to the coolant at 5 years' integrated burn time. The 150 0 C-bakeout is effective to release tritium in the surface (to 0.1 mm depth) region on the plasma side, but it is not effective to decrease the tritium inventory over the reactor life. (ii) To decrease the tritium inventory, a bakeout at a temperature higher than 150 0 C is necessary. But a high temperature bakeout causes earlier tritium permeation to the coolant. (iii) From these results it is suggested that the decrease the tritium inventory over the reactor life by bakeout, some form of protection against tritium permeation or a decontamination device in the cooling (or bakeout) system becomes necessary. (orig.)

A contemporary national nitrogen inventory as a benchmark for future progress in mitigating nitrogen pollution in the USA

Science.gov (United States)

Boyer, E. W.; Galloway, J. N.; Theis, T.; Alexander, R. B.

2011-12-01

We present a contemporary inventory of reactive nitrogen (Nr) inputs to land, air, and water in the United States. Inputs of Nr to the nation and the world have been increasing, largely due to human activities associated with food production and energy consumption via the combustion of fossil fuels and biofuels. Despite the obvious essential benefits of a plentiful supply of food and energy, the adverse consequences associated with the accumulation of Nr in the environment are large. Most of the Nr created by anthropogenic activities is released to the environment, often with unintended negative consequences. The greater the inputs of Nr to the landscape, the greater the potential for negative effects, caused by greenhouse gas production, ground level ozone, acid deposition, and Nr overload that can contribute to climate change, degradation of soils and vegetation, acidification of surface waters, coastal eutrophication, hypoxia and habitat loss. Here, we present a consistent accounting method for quantifying Nr sources and transport that was used in our inventory, and discuss associated data needs for tallying Nr inputs at regional scales. The inventory is a necessary tool for exploring the role of Nr contributed to the environment from various sources (e.g., from fertilizers, manure, biological fixation, human waste, atmospheric deposition) and from various industrial sectors (e.g., from agriculture, transportation, electricity generation). Agriculture and use of fertilizers to produce food, feed, and fiber (including bioenergy and biological nitrogen fixation) and combustion of fossil fuels are the largest sources of Nr released into the environment in the USA. Our inventory is currently being used by the U.S. Environmental Protection Agency as a benchmark of the current Nr situation against which future progress can be assessed -- amidst changing Nr inputs and implementation of policy and management strategies to mitigate Nr pollution.

Release of fission products from a fuel rod with an artificial hole through cladding irradiated in an in-pile water loop, (2)

International Nuclear Information System (INIS)

Ishiwatari, Nasumi

1978-11-01

To make clear the iodine spiking phenomenon from a defective fuel rod into the primary coolant, the fuel rod (UO 2 pellets, with stainless steel sheath) with an artificial pin hole was irradiated in the inpile test section of water loop JMTR.OWL-1. Experimental conditions were depressurization and temperature drop of the primary loop coolant and diameter and position of the pin hole. Iodine 131 and cesium 137 in loop coolant were measured under various coolant conditions. The inventory and translation rate of iodine 131 in fuel rod related to irradiation histories were calculated. The levels of I-131 and Cs-137 released to loop coolant from fuel rod were compared. Comparison of the results with LWRs was made by way of the spiked amount and release rate of iodine 131. (author)

Upper-bound fission product release assessment for large break LOCA in CANFLEX bundle reactor core

International Nuclear Information System (INIS)

Oh, Duk Ju; Lee, Kang Moon

1996-07-01

Quarter-core gap inventory assessment for CANDU-6 reactor core loaded with CANFLEX fuel bundles has been performed as one of the licensing safety analyses required for 24 natural uranium CANFLEX bundle irradiation in CANDU-6 reactor. The quarter-core gap inventory for the CANFLEX bundle core is 5 - 10 times lower than that for the standard bundle core, depending on the half-life of the isotope. The lower gap inventory of the CANFLEX bundle core is attributed to the lower linear power of the CANFLEX bundle compared with the standard bundle. However, the whole core total inventories for both the CANFLEX and standard bundle cores are nearly the same. The 6 - 8 times lower upper-bound fission product releases of the CANFLEX bundle core for large break LOCA than those of the standard bundle core imply that the loading of 24 natural uranium CANFLEX bundles would improve the predicted consequences of the postulated accident described in the Wolsung 2 safety report. 2 tabs., 6 figs., 3 refs. (Author)

Inventories and reduction scenarios of urban waste-related greenhouse gas emissions for management potential.

Science.gov (United States)

Yang, Dewei; Xu, Lingxing; Gao, Xueli; Guo, Qinghai; Huang, Ning

2018-06-01

Waste-related greenhouse gas (GHG) emissions have been recognized as one of the prominent contributors to global warming. Current urban waste regulations, however, face increasing challenges from stakeholders' trade-offs and hierarchic management. A combined method, i.e., life cycle inventories and scenario analysis, was employed to investigate waste-related GHG emissions during 1995-2015 and to project future scenarios of waste-driven carbon emissions by 2050 in a pilot low carbon city, Xiamen, China. The process-based carbon analysis of waste generation (prevention and separation), transportation (collection and transfer) and disposal (treatment and recycling) shows that the main contributors of carbon emissions are associated with waste disposal processes, solid waste, the municipal sector and Xiamen Mainland. Significant spatial differences of waste-related CO 2e emissions were observed between Xiamen Island and Xiamen Mainland using the carbon intensity and density indexes. An uptrend of waste-related CO 2e emissions from 2015 to 2050 is identified in the business as usual, waste disposal optimization, waste reduction and the integrated scenario, with mean annual growth rates of 8.86%, 8.42%, 6.90% and 6.61%, respectively. The scenario and sensitivity analysis imply that effective waste-related carbon reduction requires trade-offs among alternative strategies, actions and stakeholders in a feasible plan, and emphasize a priority of waste prevention and collection in Xiamen. Our results could benefit to the future modeling of urban multiple wastes and life-cycle carbon control in similar cities within and beyond China. Copyright © 2018 Elsevier B.V. All rights reserved.

Optimization of inventory management in furniture manufacturing

OpenAIRE

Karkauskas, Justinas

2017-01-01

Aim of research - to present inventory management optimization guidelines for furniture manufacturing company, based on analysis of scientific literature and empirical research. Tasks of the Issue: • Disclose problems of inventory management in furniture manufacturing sector; • To analyze theoretical inventory management decisions; • To develop theoretical inventory management optimization model; • Do empirical research of inventory management and present offers for optimizatio...

Comparison of global inventories of CO_2 emissions from biomass burning during 2002–2011 derived from multiple satellite products

International Nuclear Information System (INIS)

Shi, Yusheng; Matsunaga, Tsuneo; Saito, Makoto; Yamaguchi, Yasushi; Chen, Xuehong

2015-01-01

This study compared five widely used globally gridded biomass burning emissions inventories for the 2002–2011 period (Global Fire Emissions Database 3 (GFED3), Global Fire Emissions Database 4 (GFED4), Global Fire Assimilation System 1.0 (GFAS1.0), Fire INventory from NCAR 1.0 (FINN1.0) and Global Inventory for Chemistry-Climate studies-GFED4 (G-G)). Average annual CO_2 emissions range from 6521.3 to 9661.5 Tg year"−"1 for five inventories, with extensive amounts in Africa, South America and Southeast Asia. Coefficient of Variation for Southern America, Northern and Southern Africa are 30%, 39% and 48%. Globally, the majority of CO_2 emissions are released from savanna burnings, followed by forest and cropland burnings. The largest differences among the five inventories are mainly attributable to the overestimation of CO_2 emissions by FINN1.0 in Southeast Asia savanna and cropland burning, and underestimation in Southern Africa savanna and Amazon forest burning. The overestimation in Africa by G-G also contributes to the differences. - Highlights: • Five widely used global biomass burning emissions inventories were compared. • Global CO_2 emissions compared well while regional differences are large. • The largest differences were found in Southeast Asia and Southern Africa. • Savanna burning emission was the largest contributor to the global emissions. • Variations in savanna burning emission led to the differences among inventories. - Differences of the five biomass burning CO_2 emissions inventories were found in Southeast Asia and Southern Africa due to the variations in savanna burning emissions estimation.

A Psychometric Evaluation of Super's Work Values Inventory--Revised

Science.gov (United States)

Robinson, Carrie H.; Betz, Nancy E.

2008-01-01

This study describes the psychometric evaluation of Super's Work Values Inventory--Revised (SWVI-R), an instrument comprised of 12 scales measuring the relative importance placed on the following work-related value dimensions: Achievement, Coworkers, Creativity, Income, Independence, Lifestyle, Mental Challenge, Prestige, Security, Supervision,…

Hanford inventory program user's manual

International Nuclear Information System (INIS)

Hinkelman, K.C.

1994-01-01

Provides users with instructions and information about accessing and operating the Hanford Inventory Program (HIP) system. The Hanford Inventory Program is an integrated control system that provides a single source for the management and control of equipment, parts, and material warehoused by Westinghouse Hanford Company in various site-wide locations. The inventory is comprised of spare parts and equipment, shop stock, special tools, essential materials, and convenience storage items. The HIP replaced the following systems; ACA, ASP, PICS, FSP, WSR, STP, and RBO. In addition, HIP manages the catalog maintenance function for the General Supplies inventory stocked in the 1164 building and managed by WIMS

Gentamicin release from commercially-available gentamicin-loaded PMMA bone cements in a prosthesis-related interfacial gap model and their antibacterial efficacy

Directory of Open Access Journals (Sweden)

van der Mei Henny C

2010-11-01

Full Text Available Abstract Background Around about 1970, a gentamicin-loaded poly (methylmethacrylate (PMMA bone cement brand (Refobacin Palacos R was introduced to control infection in joint arthroplasties. In 2005, this brand was replaced by two gentamicin-loaded follow-up brands, Refobacin Bone Cement R and Palacos R + G. In addition, another gentamicin-loaded cement brand, SmartSet GHV, was introduced in Europe in 2003. In the present study, we investigated differences in gentamicin release and the antibacterial efficacy of the eluent between these four cement brands. Methods 200 μm-wide gaps were made in samples of each cement and filled with buffer in order to measure the gentamicin release. Release kinetics were related to bone cement powder particle characteristics and wettabilities of the cement surfaces. Gaps were also inoculated with bacteria isolated from infected prostheses for 24 h and their survival determined. Gentamicin release and bacterial survival were statistically analysed using the Student's t-test. Results All three Palacos variants showed equal burst releases but each of the successor Palacos cements showed significantly higher sustained releases. SmartSet GHV showed a significantly higher burst release, while its sustained release was comparable with original Palacos. A gentamicin-sensitive bacterium did not survive in the high gentamicin concentrations in the interfacial gaps, while a gentamicin-resistant strain did, regardless of the type of cement used. Survival was independent of the level of burst release by the bone cement. Conclusions Although marketed as the original gentamicin-loaded Palacos cement, orthopaedic surgeons should be aware that the successor cements do not appear to have the same release characteristics as the original one. Overall, high gentamicin concentrations were reached inside our prosthesis-related interfacial gap model. These concentrations may be expected to effectively decontaminate the prosthesis-related

Optimal ABC inventory classification using interval programming

NARCIS (Netherlands)

Rezaei, J.; Salimi, N.

2015-01-01

Inventory classification is one of the most important activities in inventory management, whereby inventories are classified into three or more classes. Several inventory classifications have been proposed in the literature, almost all of which have two main shortcomings in common. That is, the

An Analysis of the Optimal Multiobjective Inventory Clustering Decision with Small Quantity and Great Variety Inventory by Applying a DPSO

Science.gov (United States)

Li, Meng-Hua

2014-01-01

When an enterprise has thousands of varieties in its inventory, the use of a single management method could not be a feasible approach. A better way to manage this problem would be to categorise inventory items into several clusters according to inventory decisions and to use different management methods for managing different clusters. The present study applies DPSO (dynamic particle swarm optimisation) to a problem of clustering of inventory items. Without the requirement of prior inventory knowledge, inventory items are automatically clustered into near optimal clustering number. The obtained clustering results should satisfy the inventory objective equation, which consists of different objectives such as total cost, backorder rate, demand relevance, and inventory turnover rate. This study integrates the above four objectives into a multiobjective equation, and inputs the actual inventory items of the enterprise into DPSO. In comparison with other clustering methods, the proposed method can consider different objectives and obtain an overall better solution to obtain better convergence results and inventory decisions. PMID:25197713

Licensed-fuel-facility status report: inventory difference data, July 1981-December 1981

International Nuclear Information System (INIS)

1982-10-01

NRC is committed to the periodic publication of licensed fuel facilities inventory difference data, following agency review of the information and completion of any related investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233

Licensed fuel facility status report: Inventory difference data, January 1986-June 1986

International Nuclear Information System (INIS)

1987-02-01

NRC is committed to the periodic publication of licensed fuel facilities' inventory difference data, following agency review of the information and completion of any related investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233

Licensed fuel facility status report: Inventory difference data, January 1987-June 1987

International Nuclear Information System (INIS)

1988-03-01

NRC is committed to the periodic publication of licensed fuel facilities' inventory difference data, following agency review of the information and completion of any related investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233

Licensed fuel facility status report: Inventory difference data, July 1987-December 1987

International Nuclear Information System (INIS)

1988-09-01

NRC is committed to the periodic publication of licensed fuel facilities' inventory difference data, following agency review of the information and completion of any related investigations. Information in this report includes inventory difference data for active fuel fabrication facilities possessing more than one effective kilogram of high enriched uranium, low enriched uranium, plutonium, or uranium-233

INCAP - Applying short-term flexibility to control inventories

OpenAIRE

Lödding , Hermann; Lohmann , Steffen

2011-01-01

Abstract Inventory Based Capacity Control (INCAP) is a very simple method that allows inventory levels to be effectively controlled by using short-term capacity flexibility in make-to-stock settings. Moreover, INCAP can be used for finished goods inventories as well as for semi-finished goods inventories. The basic idea is to define upper and lower inventory limits and to adjust capacities if the inventory level reaches either limit. Should the inventory fall below the lower limit,...

Strategic Inventories in Vertical Contracts

OpenAIRE

Krishnan Anand; Ravi Anupindi; Yehuda Bassok

2008-01-01

Classical reasons for carrying inventory include fixed (nonlinear) production or procurement costs, lead times, nonstationary or uncertain supply/demand, and capacity constraints. The last decade has seen active research in supply chain coordination focusing on the role of incentive contracts to achieve first-best levels of inventory. An extensive literature in industrial organization that studies incentives for vertical controls largely ignores the effect of inventories. Does the ability to ...

Inventories and sales uncertainty\\ud

OpenAIRE

Caglayan, M.; Maioli, S.; Mateut, S.

2011-01-01

We investigate the empirical linkages between sales uncertainty and firms´ inventory investment behavior while controlling for firms´ financial strength. Using large panels of manufacturing firms from several European countries we find that higher sales uncertainty leads to larger stocks of inventories. We also identify an indirect effect of sales uncertainty on inventory accumulation through the financial strength of firms. Our results provide evidence that financial strength mitigates the a...

77 FR 5280 - Service Contracts Inventory

Science.gov (United States)

2012-02-02

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0023] Service Contracts Inventory AGENCY: Nuclear...) is providing for public information its Inventory of Contracts for Services for Fiscal Year (FY) 2011. The inventory includes service contract actions over $25,000 that were awarded in FY 2011. ADDRESSES...

78 FR 10642 - Service Contracts Inventory

Science.gov (United States)

2013-02-14

... NUCLEAR REGULATORY COMMISSION [NRC-2013-0029] Service Contracts Inventory AGENCY: Nuclear...) is providing for public information its Inventory of Contracts for Services for Fiscal Year (FY) 2012. The inventory includes service contract actions over $25,000 that were awarded in FY 2012. ADDRESSES...

SBA Network Components & Software Inventory

Data.gov (United States)

Small Business Administration — SBA’s Network Components & Software Inventory contains a complete inventory of all devices connected to SBA’s network including workstations, servers, routers,...

48 CFR 49.602-2 - Inventory forms.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Inventory forms. 49.602-2... TERMINATION OF CONTRACTS Contract Termination Forms and Formats 49.602-2 Inventory forms. Standard Form (SF) 1428, Inventory Disposal Schedule, and SF 1429, Inventory Disposal Schedule—Continuation Sheet, shall...

10 CFR 850.20 - Baseline beryllium inventory.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Baseline beryllium inventory. 850.20 Section 850.20 Energy... Baseline beryllium inventory. (a) The responsible employer must develop a baseline inventory of the... inventory, the responsible employer must: (1) Review current and historical records; (2) Interview workers...

SISTEM INVENTORI BARANG DENGAN TEKNOLOGI AJAX

Directory of Open Access Journals (Sweden)

Anna Fitriya

2015-11-01

Full Text Available ABSTRAK Sistem inventori barang pada pertokoan telah banyak dikembangkan untuk meningkatkan efektivitas dan efisiensi. Pada Toko Karya Indah, kegiatan yang berkaitan dengan inventori barang masih dilakukan secara manual sehingga pihak toko kesulitan untuk mengetahui data barang yang masih tersedia, habis, atau hampir habis. Selain itu, proses yang dilakukan membutuhkan waktu yang relatif lama. Oleh karena itu, diperlukan sistem inventori barang. Sistem dibangun dengan bahasa pemrograman PHP dan database MySQL. Sistem disertai teknologi AJAX (Asynchronous JavaScript And XML, khususnya AJAX autocomplete dan AJAX validasi. Hasil yang diperoleh adalah pengolahan data pada sistem inventori barang dengan menggunakan AJAX dapat dilakukan dengan lebih cepat dari pada tanpa AJAX. Kata kunci: sistem inventori, AJAX.

Double shell tanks plutonium inventory assessment

International Nuclear Information System (INIS)

Tusler, L.A.

1995-01-01

This report provides an evaluation that establishes plutonium inventory estimates for all DSTs based on known tank history information, the DST plutonium inventory tracking system, tank characterization measurements, tank transfer records, and estimated average concentration values for the various types of waste. These estimates use data through December 31, 1994, and give plutonium estimates as of January 1, 1995. The plutonium inventory values for the DSTs are given in Section 31. The plutonium inventory estimate is 224 kg for the DSTs and 854 kg for the SSTs for a total of 1078 kg. This value compares favorably with the total plutonium inventory value of 981 kg obtained from the total plutonium production minus plutonium recovery analysis estimates

Temporal variations in plutonium and americium inventories in the Northwestern Mediterranean Sea and their relation to vertical particulate flux

International Nuclear Information System (INIS)

Fowler, S.W.; Noshkin, V.E.; La Rosa, J.; Gastaud, J.

1999-01-01

Temporal changes in 239+240 Pu and 241 Am inventories in the western Mediterranean have been examined by making high resolution water column sampling and direct measurements of the vertical flux of particle-bound transuranics using time-series sediment traps. Water column profiles of both radionuclides showed well-defined sub-surface maxima ( 239+240 Pu between 100-400 m; 241 Am at 100-200 m and 800 m). Time-series measurements of 239+240 Pu indicated a shift in the depth of the subsurface maxima which appeared to be related to a change in depth of the core of low-salinity Levantine Intermediate Water. Total water column inventories for the western basin compared with total fallout inventories for the same area show that by 1990, approximately 56% of the 239+240 Pu and 20% of the 241 Am deposited in the basin still resided in the water column. Time-series measurements of the downward flux of particulate 239+240 Pu and 241 Am compared with transuranic removal rates derived from observed total water column inventory differences over time, show that particles sinking out of deep waters (1000-2000 m) could account for 26-72% of the computed total annual 239+240 Pu loss and virtually all of the 241 Am removal from the water column. Computed upper water column (0-200) residence times were 20-30 y for 239+240 Pu and 5-10 y for 241 Am in the open waters of the northwestern Mediterranean. A comparison with data for the north Pacific Ocean indicate that 239+240 Pu residence times are shorter and those for 241 Am much longer in open waters of the northeast Pacific. 241 Am/ 239+240 Pu activity ratios in unfiltered sea water from the western Mediterranean which are six times lower than those in the north Pacific indicate the existence of a mechanism for enhanced scavenging and removal of 241 Am from Mediterranean waters. It is proposed that frequent atmospheric inputs of aluminosilicate particles transported by Saharan dust events could enhance geochemical scavenging and

Heteroreceptors Modulating CGRP Release at Neurovascular Junction: Potential Therapeutic Implications on Some Vascular-Related Diseases

Directory of Open Access Journals (Sweden)

Abimael González-Hernández

2016-01-01

Full Text Available Calcitonin gene-related peptide (CGRP is a 37-amino-acid neuropeptide belonging to the calcitonin gene peptide superfamily. CGRP is a potent vasodilator with potential therapeutic usefulness for treating vascular-related disease. This peptide is primarily located on C- and Aδ-fibers, which have extensive perivascular presence and a dual sensory-efferent function. Although CGRP has two major isoforms (α-CGRP and β-CGRP, the α-CGRP is the isoform related to vascular actions. Release of CGRP from afferent perivascular nerve terminals has been shown to result in vasodilatation, an effect mediated by at least one receptor (the CGRP receptor. This receptor is an atypical G-protein coupled receptor (GPCR composed of three functional proteins: (i the calcitonin receptor-like receptor (CRLR; a seven-transmembrane protein, (ii the activity-modifying protein type 1 (RAMP1, and (iii a receptor component protein (RCP. Although under physiological conditions, CGRP seems not to play an important role in vascular tone regulation, this peptide has been strongly related as a key player in migraine and other vascular-related disorders (e.g., hypertension and preeclampsia. The present review aims at providing an overview on the role of sensory fibers and CGRP release on the modulation of vascular tone.

75 FR 82095 - Service Contracts Inventory

Science.gov (United States)

2010-12-29

... NUCLEAR REGULATORY COMMISSION [NRC-2010-0394] Service Contracts Inventory AGENCY: U.S. Nuclear...) is providing for public information its Inventory of Contracts for Services for Fiscal Year (FY) 2010. The inventory includes service contract actions over $25,000 that were awarded in FY 2010. ADDRESSES...

Student-Life Stress Inventory.

Science.gov (United States)

Gadzella, Bernadette M.; And Others

The reliability of the Student-Life Stress Inventory of B. M. Gadzella (1991) was studied. The inventory consists of 51 items listed in 9 sections indicating different types of stressors (frustrations, conflicts, pressures, changes, and self-imposed stressors) and reactions to the stressors (physiological, emotional, behavioral, and cognitive) as…

Uncertainties in emission inventories

NARCIS (Netherlands)

Aardenne, van J.A.

2002-01-01

Emission inventories provide information about the amount of a pollutant that is emitted to the atmosphere as a result of a specific anthropogenic or natural process at a given time or place. Emission inventories can be used for either policy or scientific purposes. For