SPEAR-BETA fuel-performance code system: fission-gas-release module. Final report

International Nuclear Information System (INIS)

Christensen, R.

1983-03-01

The original SPEAR-BETA general description manual covers both mechanistic and statistical models for fuel reliability, but only mechanistic modeling of fission gas release. This addendum covers the SPEAR-BETA statistical model for fission gas release

Field study of the long-term release of block copolymers from fouling-release coatings

DEFF Research Database (Denmark)

Noguer, Albert Camós; Olsen, A.; Hvilsted, Søren

2017-01-01

The addition of block copolymers (i.e. oils) is a common technique to enhance the biofouling-resistance properties of poly(dimethylsiloxane) (PDMS)-based fouling-release coatings. These copolymers diffuse from the bulk to the surface of the coating, thus modifying the properties of the surface an...... fouling-release coatings. Finally, the potential of long-term field-studies is discussed, as compared to short-term laboratory experiments usually performed within fouling-release coatings studies....

Updating the 2001 National Land Cover Database land cover classification to 2006 by using Landsat imagery change detection methods

Science.gov (United States)

Xian, George; Homer, Collin G.; Fry, Joyce

2009-01-01

The recent release of the U.S. Geological Survey (USGS) National Land Cover Database (NLCD) 2001, which represents the nation's land cover status based on a nominal date of 2001, is widely used as a baseline for national land cover conditions. To enable the updating of this land cover information in a consistent and continuous manner, a prototype method was developed to update land cover by an individual Landsat path and row. This method updates NLCD 2001 to a nominal date of 2006 by using both Landsat imagery and data from NLCD 2001 as the baseline. Pairs of Landsat scenes in the same season in 2001 and 2006 were acquired according to satellite paths and rows and normalized to allow calculation of change vectors between the two dates. Conservative thresholds based on Anderson Level I land cover classes were used to segregate the change vectors and determine areas of change and no-change. Once change areas had been identified, land cover classifications at the full NLCD resolution for 2006 areas of change were completed by sampling from NLCD 2001 in unchanged areas. Methods were developed and tested across five Landsat path/row study sites that contain several metropolitan areas including Seattle, Washington; San Diego, California; Sioux Falls, South Dakota; Jackson, Mississippi; and Manchester, New Hampshire. Results from the five study areas show that the vast majority of land cover change was captured and updated with overall land cover classification accuracies of 78.32%, 87.5%, 88.57%, 78.36%, and 83.33% for these areas. The method optimizes mapping efficiency and has the potential to provide users a flexible method to generate updated land cover at national and regional scales by using NLCD 2001 as the baseline.

LMFBR technology. FFTF cover-gas leakage calculation

International Nuclear Information System (INIS)

Deboi, H.

1974-01-01

The FFTF LMFBR is intended to have a near zero release of radioactive gases during normal reactor operation with 1% failed fuel. This report presents calculations which provide an approximation of these cover gas leakages. Data from ongoing static and dynamic seal leak tests at AI are utilized. Leakage through both elastomeric and metallic seals in all sub-assemblies and penetrations comprising the reactor cover gas containment during reactor operation system are included

Drug Release Studies from Caesalpinia pulcherrima Seed Polysaccharide.

Science.gov (United States)

Jeevanandham, Somasundaram; Dhachinamoorthi, Duraiswamy; Bannoth Chandra Sekhar, Kothapalli

2011-01-01

This study examines the controlled release behavior of both water-soluble (acetaminophen, caffeine, theophylline and salicylic acid) and water insoluble (indomethacin) drugs derived from Caesalpinia pulcherrima seed Gum isolated from Caesalpinia pulcherrima kernel powder. It further investigates the effect of incorporating diluents such as microcrystalline cellulose and lactose on caffeine release. In addition the effect the gum's (polysaccharide) partial cross-linking had on release of acetaminophen was examined. Applying the exponential equation, the soluble drugs mechanism of release was found to be anomalous. The insoluble drugs showed a near case II or zero order release mechanism. The rate of release in descending order was caffeine, acetaminophen, theophylline, salicylic acid and indomethacin. An increase in the release kinetics of the drug was observed on blending with diluents. However, the rate of release varied with the type and amount of blend within the matrix. The mechanism of release due to effect of diluents was found to be anomalous. The rate of drug release decreased upon partial cross-linking and the mechanism of release was found to be of super case II.

Controlled release studies of calcium alginate hydrogels

International Nuclear Information System (INIS)

Rendevski, S.; Andonovski, A.; Mahmudi, N.

2012-01-01

Controlled release of substances in many cases may be achieved from calcium alginate hydrogels. In this research, the time dependence of the mass of released model substance bovine serum albumin (BSA) from calcium alginate spherical hydrogels of three different types (G/M ratio) have been investigated. The hydrogels were prepared with the drop-wise method of sodium alginate aqueous solutions with concentration of 0.02 g/cm 3 with 0.01 g/cm 3 BSA and a gelling water bath of chitosan in 0.2 M CH 3 COOH/0.4 M CH 3 COONa with added 0.2 M CaCl 2 .The hydrogel structures were characterized by dynamic light scattering and scanning electron microscopy. The controlled release studies were conducted by UV-Vis spectrophotometry of the released medium with p H=7 at 37 °C. The results showed that the model of osmotic pumping is the dominant mechanism of the release. Also, large dependences of the release profile on the homogeneity of the hydrogels were found. (Author)

Experimental study and simulations of infiltration in evapotranspiration landfill covers

Directory of Open Access Journals (Sweden)

Wen-xian Zhang

2009-09-01

Full Text Available Various cover systems have been designed for landfill sites in order to minimize infiltration (percolation into the underlying waste. This study evaluated the soil water balance performance of evapotranspiration covers (ET covers and simulated percolation in the systems using the active region model (ARM. Experiments were conducted to measure water flow processes and water balance components in a bare soil cover and different ET covers. Results showed that vegetation played a critical role in controlling the water balance of the ET covers. In soil profiles of 60-cm depth with and without vegetation cover, the maximum soil water storage capacities were 97.2 mm and 62.8 mm, respectively. The percolation amount in the bare soil was 2.1 times that in the vegetation-covered soil. The ARM simulated percolation more accurately than the continuum model because it considered preferential flow. Numerical simulation results also indicated that using the ET cover system was an effective way of removing water through evapotranspiration, thus reducing percolation.

Overview study of LNG release prevention and control systems

Energy Technology Data Exchange (ETDEWEB)

Pelto, P.J.; Baker, E.G.; Holter, G.M.; Powers, T.B.

1982-03-01

The liquefied natural gas (LNG) industry employs a variety of release prevention and control techniques to reduce the likelihood and the consequences of accidental LNG releases. A study of the effectiveness of these release prevention and control systems is being performed. Reference descriptions for the basic types of LNG facilities were developed. Then an overview study was performed to identify areas that merit subsequent and more detailed analyses. The specific objectives were to characterize the LNG facilities of interest and their release prevention and control systems, identify possible weak links and research needs, and provide an analytical framework for subsequent detailed analyses. The LNG facilities analyzed include a reference export terminal, marine vessel, import terminal, peakshaving facility, truck tanker, and satellite facility. A reference description for these facilities, a preliminary hazards analysis (PHA), and a list of representative release scenarios are included. The reference facility descriptions outline basic process flows, plant layouts, and safety features. The PHA identifies the important release prevention operations. Representative release scenarios provide a format for discussing potential initiating events, effects of the release prevention and control systems, information needs, and potential design changes. These scenarios range from relatively frequent but low consequence releases to unlikely but large releases and are the principal basis for the next stage of analysis.

Impact of increasing antarctic glacial freshwater release on regional sea-ice cover in the Southern Ocean

Science.gov (United States)

Merino, Nacho; Jourdain, Nicolas C.; Le Sommer, Julien; Goosse, Hugues; Mathiot, Pierre; Durand, Gael

2018-01-01

The sensitivity of Antarctic sea-ice to increasing glacial freshwater release into the Southern Ocean is studied in a series of 31-year ocean/sea-ice/iceberg model simulations. Glaciological estimates of ice-shelf melting and iceberg calving are used to better constrain the spatial distribution and magnitude of freshwater forcing around Antarctica. Two scenarios of glacial freshwater forcing have been designed to account for a decadal perturbation in glacial freshwater release to the Southern Ocean. For the first time, this perturbation explicitly takes into consideration the spatial distribution of changes in the volume of Antarctic ice shelves, which is found to be a key component of changes in freshwater release. In addition, glacial freshwater-induced changes in sea ice are compared to typical changes induced by the decadal evolution of atmospheric states. Our results show that, in general, the increase in glacial freshwater release increases Antarctic sea ice extent. But the response is opposite in some regions like the coastal Amundsen Sea, implying that distinct physical mechanisms are involved in the response. We also show that changes in freshwater forcing may induce large changes in sea-ice thickness, explaining about one half of the total change due to the combination of atmospheric and freshwater changes. The regional contrasts in our results suggest a need for improving the representation of freshwater sources and their evolution in climate models.

Evaluation of the LMFBR cover gas source term and synthesis of the associated R and D

International Nuclear Information System (INIS)

Balard, F.; Carluec, B.

1996-01-01

At the end of the seventies and the beginning of the eighties, there appeared a pressing need of experimental results to assess the LMFBR's safety level. Because of the urgency, analytical studies were not systematically undertaken and maximum credible cover gas instantaneous source terms (radionuclides core release fraction) were got directly from crude out-of-pile experiment interpretations. Two types of studies and mock-ups were undertaken depending on the timescale of the phenomena: instantaneous source terms (corresponding to an unlikely energetic core disruptive accident CDA), and delayed ones (tens of minutes to some hours). The experiments performed in this frame are reviewed in this presentation: 1) instantaneous source term: - FAUST experiments: I, Cs, UO2 source terms (FzK, Germany), - FAST experiments : pool depth influence on non volatile source term (USA), - CARAVELLE experiments: nonvolatile source term in SPX1 geometry (CEA, France); 2) delayed source term: - NALA experiments: I, Cs, Sr, UO2 source term (FzK, Germany), - PAVE experiments: I source term (CEA, France), - NACOWA experiments: cover gas aerosols enrichment in I and Cs (FzK, Germany) - other French experiments in COPACABANA and GULLIVER facilities. The volatile fission products release is tightly bound to sodium evaporation and a large part of the fission products is dissolved in the liquid sodium aerosols present in the cover gas. Thus the knowledge of the amount of aerosol release to the cover gas is important for the evaluation of the source term. The maximum credible cover gas instantaneous source terms deduced from the experiments have led to conservative source terms to be taken into account in safety analysis. Nevertheless modelling attempts of the observed (in-pile or out-of-pile) physico-chemical phenomena have been undertaken for extrapolation to the reactor case. The main topics of this theoretical research are as follows: fission products evaporation in the cover gas (Fz

Drug Release Studies from Caesalpinia pulcherrima Seed Polysaccharide

OpenAIRE

Jeevanandham, Somasundaram; Dhachinamoorthi, Duraiswamy; Bannoth Chandra Sekhar, Kothapalli

2011-01-01

This study examines the controlled release behavior of both water-soluble (acetaminophen, caffeine, theophylline and salicylic acid) and water insoluble (indomethacin) drugs derived from Caesalpinia pulcherrima seed Gum isolated from Caesalpinia pulcherrima kernel powder. It further investigates the effect of incorporating diluents such as microcrystalline cellulose and lactose on caffeine release. In addition the effect the gum?s (polysaccharide) partial cross-linking had on release of aceta...

Uranium-mill-tailings remedial-action project (UMTRAP) cover and liner technology development project

International Nuclear Information System (INIS)

Hartley, J.N.; Gee, G.W.; Freeman, H.D.; Cline, J.F.; Beedlow, P.A.; Buelt, J.L.; Relyea, J.R.; Tamura, T.

1982-01-01

Cover and liner systems for uranium mill tailings in the United States must satisfy stringent requirements regarding long-term stability, radon control, and radionuclide and hazardous chemical migration. The cover placed over a tailings pile serves three basic purposes: (1) to reduce the release of radon, (2) to prevent the intrusion of plant roots and burrowing animals into the tailings, and (3) to limit surface erosion. The liner placed under a tailings pile prevents the migration of radionuclides and hazardous chemicals to groundwater. Pacific Northwest Laboratory is developing and evaluating cover and liner systems that meet these objectives and conform to federal standards. The cover and liner technology discussed in this paper involves: (1) single and multilayer earthen cover systems, (2) asphalt emulsion radon barrier systems, (3) biobarrier systems, (4) revegetation and rock covers, and (5) asphalt, clay, and synthetic liner systems. These systems have been tested at the Grand Junction, Colorado, tailings pile, where they have been shown to effectively reduce radon releases and radionuclide and chemical migration

Impacts of uranium-utilization improvements on light-water-reactor radionuclide releases

International Nuclear Information System (INIS)

Aaberg, R.L.

1981-08-01

This report discusses potential changes to radionuclide releases as a result of uranium-saving plant modifications and altered operating practices. Only releases to the environment from routine operation are considered; releases resulting from abnormal conditions outside the technical specifications covering plant operation are not considered

Radioactive materials released from nuclear power plants (1976)

International Nuclear Information System (INIS)

Decker, T.R.

1978-11-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1976 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1976 release data are compared with previous year releases in tabular form. Data covering specific radionuclides are summarized

Polymeric nanoparticles containing diazepam: preparation, optimization, characterization, in-vitro drug release and release kinetic study

Science.gov (United States)

Bohrey, Sarvesh; Chourasiya, Vibha; Pandey, Archna

2016-03-01

Nanoparticles formulated from biodegradable polymers like poly(lactic-co-glycolic acid) (PLGA) are being extensively investigated as drug delivery systems due to their two important properties such as biocompatibility and controlled drug release characteristics. The aim of this work to formulated diazepam loaded PLGA nanoparticles by using emulsion solvent evaporation technique. Polyvinyl alcohol (PVA) is used as stabilizing agent. Diazepam is a benzodiazepine derivative drug, and widely used as an anticonvulsant in the treatment of various types of epilepsy, insomnia and anxiety. This work investigates the effects of some preparation variables on the size and shape of nanoparticles prepared by emulsion solvent evaporation method. These nanoparticles were characterized by photon correlation spectroscopy (PCS), transmission electron microscopy (TEM). Zeta potential study was also performed to understand the surface charge of nanoparticles. The drug release from drug loaded nanoparticles was studied by dialysis bag method and the in vitro drug release data was also studied by various kinetic models. The results show that sonication time, polymer content, surfactant concentration, ratio of organic to aqueous phase volume, and the amount of drug have an important effect on the size of nanoparticles. Hopefully we produced spherical shape Diazepam loaded PLGA nanoparticles with a size range under 250 nm with zeta potential -23.3 mV. The in vitro drug release analysis shows sustained release of drug from nanoparticles and follow Korsmeyer-Peppas model.

Nitrogen accumulation and release by sunn hemp, calopo, mucana and devil bean in semi-arid Ghana

International Nuclear Information System (INIS)

Fosu, Mathias

2003-01-01

Four leguminous cover crops, Calopogonium mucunoides (calopo), Mucuna prupriens (mucuna), Crotalaria juncea (sunn hemp) and Crotalaria retusa (devil bean) were evaluated on the field in Northern Ghana for N 2 fixation capacity and N release. The proportion on N derived from the atmosphere (% Ndfa) by the cover crops ranged from 64.7 to 81% with mucuna giving the highest % Ndfa and calopo the least. The total N 2 fixed ranged from 59 to 109.5 kg ha 4 with devil bean giving the largest and the least from calopo. The dry matter yield of cover crops was positively correlated with the amount of N 2 , fixed but not with the percent of N derived from the atmosphere (%Ndfa). Sunn hemp, which had the best residue quality (least per cent cellulose, lignin, C N ratio and Lignin N ratio), released 50% of its N within the first two weeks while the other cover crops with relatively poor residue quality released 25% of their N within the same period. By the end of the rainy season sunn hemp had released 90% of the residue N while the other cover crops had released 80%. (author)

Immobilization and controlled release of drug using plasma polymerized thin film

Energy Technology Data Exchange (ETDEWEB)

Myung, Sung-Woon [Department of Dental Materials, School of Dentistry, MRC Center, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju (Korea, Republic of); Jung, Sang-Chul [Department of Environmental Engineering, Sunchon National University, Sunchon 540-742 (Korea, Republic of); Kim, Byung-Hoon, E-mail: kim5055@chosun.ac.kr [Department of Dental Materials, School of Dentistry, MRC Center, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju (Korea, Republic of)

2015-06-01

In this study, plasma polymerization of acrylic acid was employed to immobilize drug and control its release. Doxorubicin (DOX) was immobilized covalently on the glass surface deposited with plasma polymerized acrylic acid (PPAAc) thin film containing the carboxylic group. At first, the PPAAc thin film was coated on a glass surface at a pressure of 1.33 Pa and radio frequency (RF) discharge power of 20 W for 10 min. DOX was immobilized on the PPAAc deposition in a two environment of phosphate buffer saline (PBS) and dimethyl sulfoxide (DMSO) solutions. The DOX immobilized surface was characterized by scanning electron microscope, atomic force microscope and attenuated total reflection Fourier transform infrared spectroscopy. The DOX molecules were more immobilized in PBS than DMSO solution. The different immobilization and release profiles of DOX result from the solubility of hydrophobic DOX in aqueous and organic solutions. Second, in order to control the release of the drug, PPAAc thin film was covered over DOX dispersed layer. Different thicknesses and cross-linked PPAAc thin films by adjusting deposition time and RF discharge power were covered on the DOX layer dispersed. PPAAc thin film coated DOX layer reduced the release rate of DOX. The thickness control of plasma deposition allows controlling the release rate of drug. - Highlights: • Doxorubicin was immobilized on the surface of plasma polymerized acrylic acid thin film. • Release profile of doxorubicin was affected by aqueous and organic solutions. • Plasma polymerized acrylic acid thin film can be used to achieve controlled release.

Immobilization and controlled release of drug using plasma polymerized thin film

International Nuclear Information System (INIS)

Myung, Sung-Woon; Jung, Sang-Chul; Kim, Byung-Hoon

2015-01-01

In this study, plasma polymerization of acrylic acid was employed to immobilize drug and control its release. Doxorubicin (DOX) was immobilized covalently on the glass surface deposited with plasma polymerized acrylic acid (PPAAc) thin film containing the carboxylic group. At first, the PPAAc thin film was coated on a glass surface at a pressure of 1.33 Pa and radio frequency (RF) discharge power of 20 W for 10 min. DOX was immobilized on the PPAAc deposition in a two environment of phosphate buffer saline (PBS) and dimethyl sulfoxide (DMSO) solutions. The DOX immobilized surface was characterized by scanning electron microscope, atomic force microscope and attenuated total reflection Fourier transform infrared spectroscopy. The DOX molecules were more immobilized in PBS than DMSO solution. The different immobilization and release profiles of DOX result from the solubility of hydrophobic DOX in aqueous and organic solutions. Second, in order to control the release of the drug, PPAAc thin film was covered over DOX dispersed layer. Different thicknesses and cross-linked PPAAc thin films by adjusting deposition time and RF discharge power were covered on the DOX layer dispersed. PPAAc thin film coated DOX layer reduced the release rate of DOX. The thickness control of plasma deposition allows controlling the release rate of drug. - Highlights: • Doxorubicin was immobilized on the surface of plasma polymerized acrylic acid thin film. • Release profile of doxorubicin was affected by aqueous and organic solutions. • Plasma polymerized acrylic acid thin film can be used to achieve controlled release

Oral mucosa tissue response to titanium cover screws.

Science.gov (United States)

Olmedo, Daniel G; Paparella, María L; Spielberg, Martín; Brandizzi, Daniel; Guglielmotti, María B; Cabrini, Rómulo L

2012-08-01

Titanium is the most widely used metal in dental implantology. The release of particles from metal structures into the biologic milieu may be the result of electrochemical processes (corrosion) and/or mechanical disruption during insertion, abutment connection, or removal of failing implants. The aim of the present study is to evaluate tissue response of human oral mucosa adjacent to titanium cover screws. One hundred fifty-three biopsies of the supra-implant oral mucosa adjacent to the cover screw of submerged dental implants were analyzed. Histologic studies were performed to analyze epithelial and connective tissue as well as the presence of metal particles, which were identified using microchemical analysis. Langerhans cells, macrophages, and T lymphocytes were studied using immunohistochemical techniques. The surface of the cover screws was evaluated by scanning electron microscopy (SEM). Forty-one percent of mucosa biopsies exhibited metal particles in different layers of the section thickness. Particle number and size varied greatly among specimens. Immunohistochemical study confirmed the presence of macrophages and T lymphocytes associated with the metal particles. Microchemical analysis revealed the presence of titanium in the particles. On SEM analysis, the surface of the screws exhibited depressions and irregularities. The biologic effects seen in the mucosa in contact with the cover screws might be associated with the presence of titanium or other elements, such as aluminum or vanadium. The potential long-term biologic effects of particles on soft tissues adjacent to metallic devices should be further investigated because these effects might affect the clinical outcome of the implant.

Controlled release of diuron from an alginate-bentonite formulation: water release kinetics and soil mobility study.

Science.gov (United States)

Fernández-Pérez, M; Villafranca-Sánchez, M; González-Pradas, E; Flores-Céspedes, F

1999-02-01

The herbicide diuron was incorporated in alginate-based granules to obtain controlled release (CR) properties. The standard formulation (alginate-herbicide-water) was modified by the addition of different sorbents. The effect on diuron release rate caused by incorporation of natural and acid-treated bentonites in alginate formulation was studied by immersion of the granules in water under static conditions. The release of diuron was diffusion-controlled. The time taken for 50% release of active ingredient to be released into water, T(50), was calculated for the comparison of formulations. The addition of bentonite to the alginate-based formulation produced the higher T(50) values, indicating slower release of the diuron. The mobility of technical and formulated diuron was compared by using soil columns. The use of alginate-based CR formulations containing bentonite produced a less vertical distribution of the active ingredient as compared to the technical product and commercial formulation. Sorption capacities of the various soil constituents for diuron were also determined using batch experiments.

APASS Data Release 10

Science.gov (United States)

Henden, Arne A.; Levine, Stephen; Terrell, Dirk; Welch, Douglas L.; Munari, Ulisse; Kloppenborg, Brian K.

2018-06-01

The AAVSO Photometric All-Sky Survey (APASS) has been underway since 2010. This survey covers the entire sky from 7.5 knowledge of the optical train distortions. With these changes, DR10 includes many more stars than prior releases. We describe the survey, its remaining limitations, and prospects for the future, including a very-bright-star extension.

Comparative study of some mechanical and release properties of ...

African Journals Online (AJOL)

The mechanical and release properties of paracetamol tablets formulated with cashew gum (CAG), povidone (PVP) and gelatin (GEL) as binders were studied and compared. The parameters studied were tensile strength (TS), brittle fracture index (BFI), friability (F), disintegration time (DT) and percentage drug released ...

40 CFR 68.25 - Worst-case release scenario analysis.

Science.gov (United States)

2010-07-01

... PROGRAMS (CONTINUED) CHEMICAL ACCIDENT PREVENTION PROVISIONS Hazard Assessment § 68.25 Worst-case release... processes, one worst-case release scenario for each Program 1 process; (2) For Program 2 and 3 processes: (i... toxic substances from covered processes under worst-case conditions defined in § 68.22; (ii) One worst...

Radioactive materials released from nuclear power plants

International Nuclear Information System (INIS)

Tichler, J.; Norden, K.; Congemi, J.

1991-05-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1988 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1988 release data are summarized in tabular form. Data covering specific radionuclides are summarized. 16 tabs

Modeling of fission product release in integral codes

International Nuclear Information System (INIS)

Obaidurrahman, K.; Raman, Rupak K.; Gaikwad, Avinash J.

2014-01-01

The Great Tohoku earthquake and tsunami that stroke the Fukushima-Daiichi nuclear power station in March 11, 2011 has intensified the needs of detailed nuclear safety research and with this objective all streams associated with severe accident phenomenology are being revisited thoroughly. The present paper would cover an overview of state of art FP release models being used, the important phenomenon considered in semi-mechanistic models and knowledge gaps in present FP release modeling. Capability of FP release module, ELSA of ASTEC integral code in appropriate prediction of FP release under several diversified core degraded conditions will also be demonstrated. Use of semi-mechanistic fission product release models at AERB in source-term estimation shall be briefed. (author)

[Preparation of hydrophilic matrix sustained release tablets of total lactones from Andrographis paniculata and study on its in vitro release mechanism].

Science.gov (United States)

Xu, Fang-Fang; Shi, Wei; Zhang, Hui; Guo, Qing-Ming; Wang Zhen-Zhong; Bi, Yu-An; Wang, Zhi-Min; Xiao, Wei

2015-01-01

In this study, hydrophilic matrix sustained release tablets of total lactones from Andrographis paniculata were prepared and the in vitro release behavior were also evaluated. The optimal prescription was achieved by studying the main factor of the type and amount of hydroxypropyl methylcellulose (HPMC) using single factor test and evaluating through cumulative release of three lactones. No burst drug release from the obtained matrix tablets was observed. Drug release sustained to 14 h. The release mechanism of three lactones from A. paniculata was accessed by zero-order, first-order, Higuchi and Peppas equation. The release behavior of total lactones from A. paniculata was better agreed with Higuchi model and the drug release from the tablets was controlled by degradation of the matrix. The preparation of hydrophilic matrix sustained release tablets of total lactones from A. paniculata with good performance of drug release was simple.

Sea-ice cover in the Nordic Seas and the sensitivity to Atlantic water temperatures

Science.gov (United States)

Jensen, Mari F.; Nisancioglu, Kerim H.; Spall, Michael A.

2017-04-01

Changes in the sea-ice cover of the Nordic Seas have been proposed to play a key role for the dramatic temperature excursions associated with the Dansgaard-Oeschger events during the last glacial. However, with its proximity to the warm Atlantic water, how a sea-ice cover can persist in the Nordic Seas is not well understood. In this study, we apply an eddy-resolving configuration of the Massachusetts Institute of Technology general circulation model with an idealized topography to study the presence of sea ice in a Nordic Seas-like domain. We assume an infinite amount of warm Atlantic water present in the south by restoring the southern area to constant temperatures. The sea-surface temperatures are restored toward cold, atmospheric temperatures, and as a result, sea ice is present in the interior of the domain. However, the sea-ice cover in the margins of the Nordic Seas, an area with a warm, cyclonic boundary current, is sensitive to the amount of heat entering the domain, i.e., the restoring temperature in the south. When the temperature of the warm, cyclonic boundary current is high, the margins are free of sea ice and heat is released to the atmosphere. We show that with a small reduction in the temperature of the incoming Atlantic water, the Nordic Seas-like domain is fully covered in sea ice. Warm water is still entering the Nordic Seas, however, this happens at depths below a cold, fresh surface layer produced by melted sea ice. Consequently, the heat release to the atmosphere is reduced along with the eddy heat fluxes. Results suggest a threshold value in the amount of heat entering the Nordic Seas before the sea-ice cover disappears in the margins. We study the sensitivity of this threshold to changes in atmospheric temperatures and vertical diffusivity.

77 FR 13061 - Electronic Reporting of Toxics Release Inventory Data

Science.gov (United States)

2012-03-05

...--Reporting Year SIC--Standard Industrial Code TRI--Toxics Release Inventory TRI-ME--TRI-Made Easy Desktop... EPA to ``publish a uniform toxic chemical release form for facilities covered'' by the TRI Program. 42... practicable. Similarly, EPA's Cross-Media Electronic Reporting Regulation (CROMERR) (40 CFR Part 3), published...

Modeling percent tree canopy cover: a pilot study

Science.gov (United States)

John W. Coulston; Gretchen G. Moisen; Barry T. Wilson; Mark V. Finco; Warren B. Cohen; C. Kenneth Brewer

2012-01-01

Tree canopy cover is a fundamental component of the landscape, and the amount of cover influences fire behavior, air pollution mitigation, and carbon storage. As such, efforts to empirically model percent tree canopy cover across the United States are a critical area of research. The 2001 national-scale canopy cover modeling and mapping effort was completed in 2006,...

SkyMapper Southern Survey: First Data Release (DR1)

Science.gov (United States)

Wolf, Christian; Onken, Christopher A.; Luvaul, Lance C.; Schmidt, Brian P.; Bessell, Michael S.; Chang, Seo-Won; Da Costa, Gary S.; Mackey, Dougal; Martin-Jones, Tony; Murphy, Simon J.; Preston, Tim; Scalzo, Richard A.; Shao, Li; Smillie, Jon; Tisserand, Patrick; White, Marc C.; Yuan, Fang

2018-02-01

We present the first data release of the SkyMapper Southern Survey, a hemispheric survey carried out with the SkyMapper Telescope at Siding Spring Observatory in Australia. Here, we present the survey strategy, data processing, catalogue construction, and database schema. The first data release dataset includes over 66 000 images from the Shallow Survey component, covering an area of 17 200 deg2 in all six SkyMapper passbands uvgriz, while the full area covered by any passband exceeds 20 000 deg2. The catalogues contain over 285 million unique astrophysical objects, complete to roughly 18 mag in all bands. We compare our griz point-source photometry with Pan-STARRS1 first data release and note an RMS scatter of 2%. The internal reproducibility of SkyMapper photometry is on the order of 1%. Astrometric precision is better than 0.2 arcsec based on comparison with Gaia first data release. We describe the end-user database, through which data are presented to the world community, and provide some illustrative science queries.

A reliability study on influence of the geosphere thickness over the activity release from a near surface radioactive waste repository

Energy Technology Data Exchange (ETDEWEB)

Aguiar, Lais Alencar de, E-mail: laguiar@cnen.gov.br [Comissao Nacional de Energia Nuclear (CNEN-RJ), Rio de Janeiro, RJ (Brazil); Damaso, Vinicius Correa, E-mail: vcdamaso@gmail.com [Estado-Maior do Exercito (EME/EB), Brasilia, DF (Brazil)

2013-07-01

Infiltration of water into a waste disposal facility and into the waste region is the main factor inducing the release of radionuclides from a disposal facility. Since infiltrating water flow is dependent on the natural percolation at the site and the performance of engineered barriers, its prediction requires modelling of unsaturated water flow through intact or partially/completely failed components of engineered barriers and through the rock layer of the geosphere on which the repository is constructed. The engineered barriers include the cover systems, concrete vault, backfill, waste forms, and overpacks. This paper aims to carry out a performance study regarding a near surface repository in terms of reliability engineering. It is assumed that surface water infiltrates through the barriers reaching the matrix where radionuclides are contained, thus releasing them into the environment. The repository consists of a set of barriers which are considered saturated porous medium. As results, this paper presents the relation between the thickness of the geosphere layer and the radionuclide release rate in terms of activity. Such results represent a useful information for choosing the repository sites in order to keep the released activity in acceptable levels over time. (author)

A reliability study on influence of the geosphere thickness over the activity release from a near surface radioactive waste repository

International Nuclear Information System (INIS)

Aguiar, Lais Alencar de; Damaso, Vinicius Correa

2013-01-01

Infiltration of water into a waste disposal facility and into the waste region is the main factor inducing the release of radionuclides from a disposal facility. Since infiltrating water flow is dependent on the natural percolation at the site and the performance of engineered barriers, its prediction requires modelling of unsaturated water flow through intact or partially/completely failed components of engineered barriers and through the rock layer of the geosphere on which the repository is constructed. The engineered barriers include the cover systems, concrete vault, backfill, waste forms, and overpacks. This paper aims to carry out a performance study regarding a near surface repository in terms of reliability engineering. It is assumed that surface water infiltrates through the barriers reaching the matrix where radionuclides are contained, thus releasing them into the environment. The repository consists of a set of barriers which are considered saturated porous medium. As results, this paper presents the relation between the thickness of the geosphere layer and the radionuclide release rate in terms of activity. Such results represent a useful information for choosing the repository sites in order to keep the released activity in acceptable levels over time. (author)

Study of the Release Process of Open Source Software: Case Study

OpenAIRE

Eide, Tor Erik

2007-01-01

This report presents the results of a case study focusing on the release process of open source projects initiated with commercial motives. The purpose of the study is to gain an increased understanding of the release process, how a community can be attracted to the project, and how the interaction with the community evolves in commercial open source initiatives. Data has been gathered from four distinct sources to form the basis of this thesis. A thorough review of the open source literatu...

Biocompatibility of a new device of self-expandable covered and non-covered tracheal stent: comparative study in rats

Directory of Open Access Journals (Sweden)

Olavo Ribeiro Rodrigues

2013-01-01

Full Text Available PURPOSE: To investigate the compatibility of a new model of self-expandable tracheal stent in rats. METHODS: A new device of polyurethane covered and non - covered stent was placed in the trachea of Wistar rats. Animals were distributed in two groups: the polyurethane covered and non-covered group. Macroscopic parameters included position within the tracheal lumen, adherence to the mucosa, degree of dilatation, permeability and internal diameter. Microscopic findings evaluated were: incorporation, inflammatory activity, granulation tissue and epithelial revetment injuries. The observation follow-up was six weeks. All parameters were quantified based on determined score values. Incorporation of the stents was evaluated based on the observation if the stent was fixed into the trachea or if it could be removed. Degree of dilatation was performed by external diameter measurements. Granulation tissue was evaluated by measurements of height of the tissue growing into the tracheal lumen. RESULTS: 100% of non-covered stents had total attachment to mucosa and 100% of polyurethane covered type had adherence only. Regarding dilatation, granulation tissue, inflammatory activity and internal diameter measurements, there were no significant differences between the groups. Pathological tracheal wall injuries were present in both groups. CONCLUSION: Both models of stent demonstrated biocompatibility with the trachea. Rats are suitable for an experimental model of tracheal stent study.

Cover gas purification experience at KNK

Energy Technology Data Exchange (ETDEWEB)

Richard, H; Stade, K Ch [Kernkraftwerk-Betriebsgesellschaft m.b.H., Eggenstein-Leopoldshafen (Germany); Stamm, H H [Institute of Radiochemistry, Nuclear Research Center, Karsruhe (Germany)

1987-07-01

KNK II is an experimental, sodium cooled fast breeder reactor. The reactor was operated until 1974 with a thermal core (KNK I). The plant was converted into a fast breeder reactor (KNK II) from 1974 to 1977. The commissioning of KNK II was started in October 1977 with the first fast core KNK 11/1. After 400 effective full power days (EFPD) the reactor was shut down in August 1982. After replacing the complete core by the second fast core KNK 11/2, the plant went into operation again in August 1983. In August 1986 nearly 400 EFPD were achieved with the second fast core. Argon is used as cover gas in the primary and secondary sodium systems of KNK. In former times fresh argon was supplied by a bundle of gas cylinders. Later on a liquid argon supply was installed. Purification of cover gas is done by flushing only. During KNK I operation no fuel failures occurred. The primary cover gas activity was characterized by the formation of Ar-41, only small quantities of fission gas were measured, released from 'tramp uranium'. Therefore, no problems existed during KNK I operation with regard to radioactive gas disposal. However, after start-up of KNK II, several fuel elements failed. Until August 1986, five fuel failures were observed, two in KNK 11/1, and three in KNK 11/2. Sometimes, operation with defective fuel pins caused problems when fission gases leaked into the containment atmosphere, and the access had to be restricted. The purging rate of the primary cover gas was limited by the capacity of the charcoal filters in the delay line. Of all non-radioactive impurities, hydrogen (H{sub z}) and nitrogen (N{sub 2}) were of most importance in the primary cover gas. Main source of both impurities was the ingress of air and atmospheric moisture during handling operations in shutdown periods. An other possible source for hydrogen might be a release from the steel-clad zirconium hydride, used as moderator in the moderated driver fuel elements. Additional nitrogen may diffuse

Cover Crops Effects on Soil Chemical Properties and Onion Yield

Directory of Open Access Journals (Sweden)

Rodolfo Assis de Oliveira

2016-01-01

Full Text Available ABSTRACT Cover crops contribute to nutrient cycling and may improve soil chemical properties and, consequently, increase crop yield. The aim of this study was to evaluate cover crop residue decomposition and nutrient release, and the effects of these plants on soil chemical properties and on onion (Allium cepa L. yield in a no-tillage system. The experiment was carried out in an Inceptisol in southern Brazil, where cover crops were sown in April 2012 and 2013. In July 2013, shoots of weeds (WD, black oats (BO, rye (RY, oilseed radish (RD, oilseed radish + black oats (RD + BO, and oilseed radish + rye (RD + RY were cut at ground level and part of these material from each treatment was placed in litter bags. The litter bags were distributed on the soil surface and were collected at 0, 30, 45, 60, 75, and 90 days after distribution (DAD. The residues in the litter bags were dried, weighed, and ground, and then analyzed to quantify lignin, cellulose, non-structural biomass, total organic carbon (TOC, N, P, K, Ca, and Mg. In November 2012 and 2013, onion crops were harvested to quantify yield, and bulbs were classified according to diameter, and the number of rotted and flowering bulbs was determined. Soil in the 0.00-0.10 m layer was collected for chemical analysis before transplanting and after harvesting onion in December 2012 and 2013. The rye plant residues presented the highest half-life and they released less nutrients until 90 DAD. The great permanence of rye residue was considered a protection to soil surface, the opposite was observed with spontaneous vegetation. The cultivation and addition of dry residue of cover crops increased the onion yield at 2.5 Mg ha-1.

Impact Response Study on Covering Cap of Aircraft Big-Size Integral Fuel Tank

Science.gov (United States)

Wang, Fusheng; Jia, Senqing; Wang, Yi; Yue, Zhufeng

2016-10-01

In order to assess various design concepts and choose a kind of covering cap design scheme which can meet the requirements of airworthiness standard and ensure the safety of fuel tank. Using finite element software ANSYS/LS- DYNA, the impact process of covering cap of aircraft fuel tank by projectile were simulated, in which dynamical characteristics of simple single covering cap and gland double-layer covering cap impacted by titanium alloy projectile and rubber projectile were studied, as well as factor effects on simple single covering cap and gland double-layer covering cap under impact region, impact angle and impact energy were also studied. Though the comparison of critical damage velocity and element deleted number of the covering caps, it shows that the external covering cap has a good protection effect on internal covering cap. The regions close to boundary are vulnerable to appear impact damage with titanium alloy projectile while the regions close to center is vulnerable to occur damage with rubber projectile. Equivalent strain in covering cap is very little when impact angle is less than 15°. Element deleted number in covering cap reaches the maximum when impact angle is between 60°and 65°by titanium alloy projectile. While the bigger the impact angle and the more serious damage of the covering cap will be when rubber projectile impact composite covering cap. The energy needed for occurring damage on external covering cap and internal covering cap is less than and higher than that when single covering cap occur damage, respectively. The energy needed for complete breakdown of double-layer covering cap is much higher than that of single covering cap.

Radioactive materials released from nuclear power plants. Annual report 1977

International Nuclear Information System (INIS)

Decker, T.R.

1978-11-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1977 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1977 release data are compared with previous years releases in tabular form. Data covering specific radionuclides are summarized

Metal mobilization under alkaline conditions in ash-covered tailings.

Science.gov (United States)

Lu, Jinmei; Alakangas, Lena; Wanhainen, Christina

2014-06-15

The aim of this study was to determine element mobilization and accumulation in mill tailings under alkaline conditions. The tailings were covered with 50 cm of fly ash, and above a sludge layer. The tailings were geochemically and mineralogically investigated. Sulfides, such as pyrrhotite, sphalerite and galena along with gangue minerals such as dolomite, calcite, micas, chlorite, epidote, Mn-pyroxene and rhodonite were identified in the unoxidized tailings. The dissolution of the fly ash layer resulted in a high pH (close to 12) in the underlying tailings. This, together with the presence of organic matter, increased the weathering of the tailings and mobilization of elements in the uppermost 47 cm of the tailings. All primary minerals were depleted, except quartz and feldspar which were covered by blurry secondary carbonates. Sulfide-associated elements such as Cd, Fe, Pb, S and Zn and silicate-associated elements such as Fe, Mg and Mn were released from the depletion zone and accumulated deeper down in the tailings where the pH decreased to circum-neutral. Sequential extraction suggests that Cd, Cu, Fe, Pb, S and Zn were retained deeper down in the tailings and were mainly associated with the sulfide phase. Calcium, Cr, K and Ni released from the ash layer were accumulated in the uppermost depletion zone of the tailings. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Decade of Annual National Land Cover Products - the Cropland Data Layer

Science.gov (United States)

Mueller, R.; Johnson, D. M.; Sandborn, A.; Willis, P.; Ebinger, L.; Yang, Z.; Seffrin, R.; Boryan, C. G.; Hardin, R.

2017-12-01

The Cropland Data Layer (CDL) is a national land cover product produced by the US Department of Agriculture/National Agricultural Statistics Service (NASS) to assess planted crop acreage on an annual basis. The 2017 CDL product serves as the decadal anniversary for the mapping of conterminous US agriculture. The CDL is a supervised land cover classification derived from medium resolution Earth observing satellites that capture crop phenology throughout the growing season, leveraging confidentially held ground reference information from the USDA Farm Service Agency (FSA) as training data. The CDL currently uses ancillary geospatial data from the US Geological Survey's National Land Cover Database (NLCD), and Imperviousness and Forest Canopy layers as well as the National Elevation Dataset as training for the non-agricultural domain. Accuracy assessments are documented and released annually with metadata publication. NASS is currently reprocessing the 2008 and 2009 CDL products to 30m resolution. They were originally processed and released at 56m based on the Resourcesat-1 AWiFS sensor. Additionally, best practices learned from processing the FSA ground reference data were applied to the historical training set, providing an enhanced classification at 30m. The release of these reprocessed products in the fall of 2017, along with the 2017 CDL annual product will be discussed and will complete a decade's worth of annual 30m products. Discussions of change and trend analytics as well as partnerships with key industry stakeholders will be displayed on the evolution and improvements made to this decadal geospatial crop specific land cover product.

Simulation and parametric study of a film-coated controlled-release pharmaceutical.

Science.gov (United States)

Borgquist, Per; Zackrisson, Gunnar; Nilsson, Bernt; Axelsson, Anders

2002-04-23

Pharmaceutical formulations can be designed as Multiple Unit Systems, such as Roxiam CR, studied in this work. The dose is administrated as a capsule, which contains about 100 individual pellets, which in turn contain the active drug remoxipride. Experimental data for a large number of single pellets can be obtained by studying the release using microtitre plates. This makes it possible to study the release of the individual subunits making up the total dose. A mathematical model for simulating the release of remoxipride from single film-coated pellets is presented including internal and external mass transfer hindrance apart from the most important film resistance. The model can successfully simulate the release of remoxipride from single film-coated pellets if the lag phase of the experimental data is ignored. This was shown to have a minor influence on the release rate. The use of the present model is demonstrated by a parametric study showing that the release process is film-controlled, i.e. is limited by the mass transport through the polymer coating. The model was used to fit the film thickness and the drug loading to the experimental release data. The variation in the fitted values was similar to that obtained in the experiments.

EPICS release 3.11.6 specific documentation -- Release notes for EPICS 3.11.6

International Nuclear Information System (INIS)

1994-01-01

These notes cover the following: (1) directions for switching to production APS release R3.11.6; (2) unbundling of channel access clients; (3) access security; (4) channel access additions; synchronous time support; and (5) description of major differences between R3.11.3 and R3.11.6 Also included is a list of new and/or updated documentation for the program

Modeling the influence of snow cover temperature and water content on wet-snow avalanche runout

Directory of Open Access Journals (Sweden)

C. Vera Valero

2018-03-01

Full Text Available Snow avalanche motion is strongly dependent on the temperature and water content of the snow cover. In this paper we use a snow cover model, driven by measured meteorological data, to set the initial and boundary conditions for wet-snow avalanche calculations. The snow cover model provides estimates of snow height, density, temperature and liquid water content. This information is used to prescribe fracture heights and erosion heights for an avalanche dynamics model. We compare simulated runout distances with observed avalanche deposition fields using a contingency table analysis. Our analysis of the simulations reveals a large variability in predicted runout for tracks with flat terraces and gradual slope transitions to the runout zone. Reliable estimates of avalanche mass (height and density in the release and erosion zones are identified to be more important than an exact specification of temperature and water content. For wet-snow avalanches, this implies that the layers where meltwater accumulates in the release zone must be identified accurately as this defines the height of the fracture slab and therefore the release mass. Advanced thermomechanical models appear to be better suited to simulate wet-snow avalanche inundation areas than existing guideline procedures if and only if accurate snow cover information is available.

Studies on Fragrance Delivery from Inorganic Nanocontainers: Encapsulation, Release and Modeling Studies

Science.gov (United States)

Ghodke, Shailesh Adinath; Sonawane, Shirish Hari; Bhanvase, Bharat Apparao; Mishra, Satyendra; Joshi, Kalpana Shrikant

2015-04-01

The present work deals with encapsulation of fragrance molecule in inorganic nanocontainers substrate and investigation of its prolonged release at different pH condition. The nanocontainers used were aluminosilicate clay (Halloysite) having cylindrical shape with outside diameter in the range of 30-50 nm, 15 nm lumen and length equal to 800 ± 300 nm. Rosewater absolute was used as a sample fragrance for loading in nanocontainer and delivery purpose. The fragrance loaded nanocontainers were coated with a thin layer of polyelectrolyte i.e. Polyacrylic Acid (PAA). The structural characteristics of prepared nanocontainers were determined by using Fourier Transform Intra-red Spectroscopy (FTIR), Thermal Gravimetric Analysis (TGA) and UV spectroscopy analysis. Release of fragrance molecules in the aqueous medium was monitored for 24 h. The fragrance release was found to be responsive as the amount of fragrance release increases with increase in pH value from 3 to 7. Fragrance release has been studied by using various permeation kinetic models such as zero order, first order, Hixson-Crowell, Higuchi, Korsmeyer-Peppas and Hopfenberg models. Korsemyer-Peppas shows the best fit (R2 = 0.9544) compared to other kinetic model for the release of fragrance from nanocontainers.

Safeguarding of emergency core cooling in case of loss-of-coolant accidents with insulation material release

International Nuclear Information System (INIS)

Pointner, W.; Broecker, A.

2012-01-01

The report on safeguarding of emergency core cooling in case of loss-of-coolant accidents with insulation material release covers the following issues: assessment of the relevant status for PWR, evaluation of the national and international (USA, Canada, France) status, actualization of recommendations, transferability from PWR to BWR. Generic studies on the core cooling capability in case of insulation material release in BWR-type reactors were evaluated.

Cover gas purification in the German LMFBR-programme

International Nuclear Information System (INIS)

Schillings, K.-L.; Wagner, J.; Stade, K. Ch.

1987-01-01

A specific problem of sodium-cooled reactor plants is the purity of the noble gas argon which is used to protect the liquid alkali metal sodium in its systems in order to avoid or reduce disagreeable reactions between sodium and gaseous compounds like moisture or air and organic products like oil and grease. But as this contact cannot completely be excluded, we have to recycle such soiled cover gas. Simultaneously this procedure has to correct the release of radioactivity. Therefore the cover gas purification of primary systems of reactor plants contains the removal of the inorganic chemical disposal and of the nuclear waste. (author)

Effects of grain-producing cover crops on rice grain yield in Cabo Delgado, Mozambique

Directory of Open Access Journals (Sweden)

Adriano Stephan Nascente

Full Text Available ABSTRACT Besides providing benefits to the environment such as soil protection, release of nutrients, soil moisture maintenance, and weed control, cover crops can increase food production for grain production. The aim of this study was to evaluate the production of biomass and grain cover crops (and its respective effects on soil chemical and physical attributes, yield components, and grain yield of rice in Mozambique. The study was conducted in two sites located in the province of Cabo Delgado, in Mozambique. The experimental design was a randomized block in a 2 × 6 factorial, with four repetitions. Treatments were carried out in two locations (Cuaia and Nambaua with six cover crops: Millet (Pennisetum glaucum L.; namarra bean (Lablab purpureus (L. Sweet, velvet beans (Mucuna pruriens L., oloco beans (Vigna radiata (L. R. Wilczek, cowpea (Vigna unguiculata L., and fallow. Cover crops provided similar changes in chemical and physical properties of the soil. Lablab purpureus, Vigna unguiculata, and Mucuna pruriens produced the highest dry matter biomass. Vigna unguiculada produced the highest amount of grains. Rice grain yields were similar under all cover crops and higher in Cuaia than Nambaua.

Branched polynomial covering maps

DEFF Research Database (Denmark)

Hansen, Vagn Lundsgaard

2002-01-01

A Weierstrass polynomial with multiple roots in certain points leads to a branched covering map. With this as the guiding example, we formally define and study the notion of a branched polynomial covering map. We shall prove that many finite covering maps are polynomial outside a discrete branch ...... set. Particular studies are made of branched polynomial covering maps arising from Riemann surfaces and from knots in the 3-sphere. (C) 2001 Elsevier Science B.V. All rights reserved.......A Weierstrass polynomial with multiple roots in certain points leads to a branched covering map. With this as the guiding example, we formally define and study the notion of a branched polynomial covering map. We shall prove that many finite covering maps are polynomial outside a discrete branch...

Atomic force microscopy analysis of synthetic membranes applied in release studies

Energy Technology Data Exchange (ETDEWEB)

Olejnik, Anna, E-mail: annamar@amu.edu.pl; Nowak, Izabela

2015-11-15

Graphical abstract: - Highlights: • We compare eight synthetic membranes by atomic force microscopy. • We predict the behavior of membranes in the release experiments. • The polymeric synthetic membranes varied in shape and size. • We detect substructures in pores of cellulose esters and nylon membranes. • Substructures limit the release rate of active compound. - Abstract: Synthetic membranes are commonly used in drug release studies and are applied mostly in quality control. They contain pores through which the drug can be diffused directly into the receptor fluid. Investigation of synthetic membranes permits determination of their structure and characterization of their properties. We suggest that the preliminary characterization of the membranes can be relevant to the interpretation of the release results. The aim of this study was to compare eight synthetic membranes by using atomic force microscopy in order to predict and understand their behavior in the release experiments. The results proved that polytetrafluoroethylene membrane was not suitable for the release study of tetrapeptide due to its hydrophobic nature, thickness and the specific structure with high trapezoid shaped blocks. The additional substructures in pores of mixed cellulose esters and nylon membranes detected by AFM influenced the diffusion rate of the active compound. These findings indicate that the selection of the membrane for the release studies should be performed cautiously by taking into consideration the membrane properties and by analyzing them prior the experiment.

Atomic force microscopy analysis of synthetic membranes applied in release studies

International Nuclear Information System (INIS)

Olejnik, Anna; Nowak, Izabela

2015-01-01

Graphical abstract: - Highlights: • We compare eight synthetic membranes by atomic force microscopy. • We predict the behavior of membranes in the release experiments. • The polymeric synthetic membranes varied in shape and size. • We detect substructures in pores of cellulose esters and nylon membranes. • Substructures limit the release rate of active compound. - Abstract: Synthetic membranes are commonly used in drug release studies and are applied mostly in quality control. They contain pores through which the drug can be diffused directly into the receptor fluid. Investigation of synthetic membranes permits determination of their structure and characterization of their properties. We suggest that the preliminary characterization of the membranes can be relevant to the interpretation of the release results. The aim of this study was to compare eight synthetic membranes by using atomic force microscopy in order to predict and understand their behavior in the release experiments. The results proved that polytetrafluoroethylene membrane was not suitable for the release study of tetrapeptide due to its hydrophobic nature, thickness and the specific structure with high trapezoid shaped blocks. The additional substructures in pores of mixed cellulose esters and nylon membranes detected by AFM influenced the diffusion rate of the active compound. These findings indicate that the selection of the membrane for the release studies should be performed cautiously by taking into consideration the membrane properties and by analyzing them prior the experiment.

From the Cover: 7,8-Dihydroxyflavone Rescues Lead-Induced Impairment of Vesicular Release: A Novel Therapeutic Approach for Lead Intoxicated Children.

Science.gov (United States)

Zhang, Xiao-Lei; McGlothan, Jennifer L; Miry, Omid; Stansfield, Kirstie H; Loth, Meredith K; Stanton, Patric K; Guilarte, Tomás R

2018-01-01

Childhood lead (Pb2+) intoxication is a public health problem of global proportion. Lead exposure during development produces multiple effects on the central nervous system including impaired synapse formation, altered synaptic plasticity, and learning deficits. In primary hippocampal neurons in culture and hippocampal slices, Pb2+ exposure inhibits vesicular release and reduces the number of fast-releasing sites, an effect associated with Pb2+ inhibition of NMDA receptor-mediated trans-synaptic Brain-Derived Neurotrophic Factor (BDNF) signaling. The objective of this study was to determine if activation of TrkB, the cognate receptor for BDNF, would rescue Pb2+-induced impairments of vesicular release. Rats were chronically exposed to Pb2+ prenatally and postnatally until 50 days of age. This chronic Pb2+ exposure paradigm enhanced paired-pulse facilitation of synaptic potentials in Schaffer collateral-CA1 synapses in the hippocampus, a phenomenon indicative of reduced vesicular release probability. Decreased vesicular release probability was confirmed by both mean-variance analysis and direct 2-photon imaging of vesicular release from hippocampal slices of rats exposed to Pb2+in vivo. We also found a Pb2+-induced impairment of calcium influx in Schaffer collateral-CA1 synaptic terminals. Intraperitoneal injections of Pb2+ rats with the TrkB receptor agonist 7,8-dihydroxyflavone (5 mg/kg) for 14-15 days starting at postnatal day 35, reversed all Pb2+-induced impairments of presynaptic transmitter release at Schaffer collateral-CA1 synapses. This study demonstrates for the first time that in vivo pharmacological activation of TrkB receptors by small molecules such as 7,8-dihydroxyflavone can reverse long-term effects of chronic Pb2+ exposure on presynaptic terminals, pointing to TrkB receptor activation as a promising therapeutic intervention in Pb2+-intoxicated children. © The Author 2017. Published by Oxford University Press on behalf of the Society of

Barrier and operational risk analysis of hydrocarbon releases (BORA-Release)

International Nuclear Information System (INIS)

Sklet, Snorre; Vinnem, Jan Erik; Aven, Terje

2006-01-01

This paper presents results from a case study carried out on an offshore oil and gas production platform with the purpose to apply and test BORA-Release, a method for barrier and operational risk analysis of hydrocarbon releases. A description of the BORA-Release method is given in Part I of the paper. BORA-Release is applied to express the platform specific hydrocarbon release frequencies for three release scenarios for selected systems and activities on the platform. The case study demonstrated that the BORA-Release method is a useful tool for analysing the effect on the release frequency of safety barriers introduced to prevent hydrocarbon releases, and to study the effect on the barrier performance of platform specific conditions of technical, human, operational, and organisational risk influencing factors (RIFs). BORA-Release may also be used to analyse the effect on the release frequency of risk reducing measures

Radioactive iodine releases from nuclear power plant, (1)

International Nuclear Information System (INIS)

Hashimoto, Tatsuya

1974-01-01

Concerning the release of radioactive iodine from nuclear power plants, the guidelines and data both in Japan and abroad are briefed, including those in the United States, Tsuruga nuclear power station and working Group of the Environmental Radiation Study Committee. In case of the Tsuruga nuclear power station, the radiation dose and other data for a few years are presented. Parameters and factors proposed by the working group cover such as the dose through food intake and respiration, concentration factor, etc. (Mori, K.)

'COVER STORY': A STUDY IN lAND MANAGEMENT

African Journals Online (AJOL)

The group was concerned with soil ero- sion and the associated effect upon the vegetation cover. The first s~ge of the project was to est- ablish exactly which aspects of soil erosion should be studied. The following points were initially considered: soil types and characteristics different grasses and their carrying capacity.

Monitoring of covering model of the National radioactive waste repository

International Nuclear Information System (INIS)

Jezikova, M.

2009-01-01

The subject of this rigorous report is justification of cover model building at radioactive waste repository in Mochovce as a very important engineering barrier preventing significant release of radioactive substances into the environment and providing protection against ionizing radiation. This rigorous report includes a theoretical part, which describes radioactive waste characterization, radioactive waste management and summary of the preliminary activities prior to the building cover model, particularly involving the selection of appropriate variables and parameters and creation of monitoring plan during the long term monitoring for evaluation of this barrier in order to ensure minimization of any leak of radioactive substances from RAW. The next part includes evaluation of the values of parameters and variables to build cover model of RAW in Mochovce during 2006-2008 (author)

Controlled release hydrophilic matrix tablet formulations of isoniazid: design and in vitro studies.

Science.gov (United States)

Hiremath, Praveen S; Saha, Ranendra N

2008-01-01

The aim of the present investigation was to develop oral controlled release matrix tablet formulations of isoniazid using hydroxypropyl methylcellulose (HPMC) as a hydrophilic release retardant polymer and to study the influence of various formulation factors like proportion of the polymer, polymer viscosity grade, compression force, and release media on the in vitro release characteristics of the drug. The formulations were developed using wet granulation technology. The in vitro release studies were performed using US Pharmacopoeia type 1 apparatus (basket method) in 900 ml of pH 7.4 phosphate buffer at 100 rpm. The release kinetics was analyzed using Korsmeyer-Peppas model. The release profiles were also analyzed using statistical method (one-way analysis of variance) and f (2) metric values. The release profiles found to follow Higuchi's square root kinetics model irrespective of the polymer ratio and the viscosity grade used. The results in the present investigation confirm that the release rate of the drug from the HPMC matrices is highly influenced by the drug/HPMC ratio and viscosity grade of the HPMC. Also, the effect of compression force and release media was found to be significant on the release profiles of isoniazid from HPMC matrix tablets. The release mechanism was found to be anomalous non-Fickian diffusion in all the cases. In the present investigation, a series of controlled release formulations of isoniazid were developed with different release rates and duration so that these formulations could further be assessed from the in vivo bioavailability studies. The formulations were found to be stable and reproducible.

The Resolved Stellar Populations Early Release Science Program

Science.gov (United States)

Gilbert, Karoline; Weisz, Daniel; Resolved Stellar Populations ERS Program Team

2018-06-01

The Resolved Stellar Populations Early Release Science Program (PI D. Weisz) will observe Local Group targets covering a range of stellar density and star formation histories, including a globular cluster, and ultra-faint dwarf galaxy, and a star-forming dwarf galaxy. Using observations of these diverse targets we will explore a broad science program: we will measure star formation histories, the sub-solar stellar initial mass function, and proper motions, perform studies of evolved stars, and map extinction in the target fields. Our observations will be of high archival value for other science such as calibrating stellar evolution models, studying variable stars, and searching for metal-poor stars. We will determine optimal observational setups and develop data reduction techniques that will be common to JWST studies of resolved stellar populations. We will also design, test, and release point spread function (PSF) fitting software specific to NIRCam and NIRISS, required for the crowded stellar regime. Prior to the Cycle 2 Call for Proposals, we will release PSF fitting software, matched HST and JWST catalogs, and clear documentation and step-by-step tutorials (such as Jupyter notebooks) for reducing crowded stellar field data and producing resolved stellar photometry catalogs, as well as for specific resolved stellar photometry science applications.

Release of Chlorine and Sulfur during Biomass Torrefaction and Pyrolysis

DEFF Research Database (Denmark)

Saleh, Suriyati Binti; Flensborg, Julie Pauline; Shoulaifar, Tooran Khazraie

2014-01-01

The release of chlorine (Cl) and sulfur (S) during biomass torrefaction and pyrolysis has been investigated via experiments in two laboratory-scale reactors: a rotating reactor and a fixed bed reactor. Six biomasses with different chemical compositions covering a wide range of ash content and ash...... reporting that biomasses with a lower chlorine content release a higher fraction of chlorine during the pyrolysis process. A significant sulfur release (about 60%) was observed from the six biomasses investigated at 350 degrees C. The initial sulfur content in the biomass did not influence the fraction...

Absorption of Nickel, Chromium, and Iron by the Root Surface of Primary Molars Covered with Stainless Steel Crowns

Directory of Open Access Journals (Sweden)

David Keinan

2010-01-01

Full Text Available Objective. The purpose of this study was to analyze the absorption of metal ions released from stainless steel crowns by root surface of primary molars. Study Design. Laboratory research: The study included 34 primary molars, exfoliated or extracted during routine dental treatment. 17 molars were covered with stainless-steel crowns for more than two years and compared to 17 intact primary molars. Chemical content of the mesial or distal root surface, 1 mm apically to the crown or the cemento-enamel junction (CEJ, was analyzed. An energy dispersive X-ray spectrometer (EDS was used for chemical analysis. Results. Higher amounts of nickel, chromium, and iron (5-6 times were found in the cementum of molars covered with stainless-steel crowns compared to intact molars. The differences between groups were highly significant (<.001. Significance. Stainless-steel crowns release nickel, chromium, and iron in oral environment, and the ions are absorbed by the primary molars roots. The additional burden of allergenic metals should be reduced if possible.

Dating gasoline releases using ground-water chemical analyses: Case studies

International Nuclear Information System (INIS)

Worthington, M.A.; Perez, E.J.

1993-01-01

This paper presents case studies where geochemical data were analyzed in spatial and temporal relation to documented gasoline releases at typical service station sites. In particular, the authors present ground-water analytical data for sites where (1) the date of the gasoline release is known with a good degree of confidence, (2) the release is confined to a relatively short period of time so as to be considered essentially instantaneous, (3) antecedent geochemical condition are known or can be reasonably expected to have been either unaffected by previous hydrocarbon impacts or minor in comparison to known release events, and (4) where geologic materials can be classified as to structure and composition. The authors' intent is to provide empirical data regarding the hydrogeological fate of certain gasoline components, namely the compounds benzene, toluene, ethylbenzene and xylene isomers (BTEX) and methyl-tertiary-butyl ether (MTBE). Particular emphasis is placed on analysis of gasoline weathering as a means of comparing releases in given hydrogeologic environments. Trends seen in a variety of comparative hydrocarbon compound ratios may provide a basis for evaluating relative release dates

Branched polynomial covering maps

DEFF Research Database (Denmark)

Hansen, Vagn Lundsgaard

1999-01-01

A Weierstrass polynomial with multiple roots in certain points leads to a branched covering map. With this as the guiding example, we formally define and study the notion of a branched polynomial covering map. We shall prove that many finite covering maps are polynomial outside a discrete branch...... set. Particular studies are made of branched polynomial covering maps arising from Riemann surfaces and from knots in the 3-sphere....

Experimental study of PLLA/INH slow release implant fabricated by three dimensional printing technique and drug release characteristics in vitro.

Science.gov (United States)

Wu, Gui; Wu, Weigang; Zheng, Qixin; Li, Jingfeng; Zhou, Jianbo; Hu, Zhilei

2014-07-19

Local slow release implant provided long term and stable drug release in the lesion. The objective of this study was to fabricate biodegradable slow release INH/PLLA tablet via 3 dimensional printing technique (3DP) and to compare the drug release characteristics of three different structured tablets in vitro. Three different drug delivery systems (columnar-shaped tablet (CST), doughnut-shaped tablet (DST) and multilayer doughnut-shaped tablet (MDST)) were manufactured by the three dimensional printing machine and isoniazid was loaded into the implant. Dynamic soaking method was used to study the drug release characteristics of the three implants. MTT cytotoxicity test and direct contact test were utilized to study the biocompatibility of the implant. The microstructures of the implants' surfaces were observed with electron microscope. The PLLA powder in the tablet could be excellently combined through 3DP without disintegration. Electron microscope observations showed that INH distributed evenly on the surface of the tablet in a "nest-shaped" way, while the surface of the barrier layer in the multilayer doughnut shaped tablet was compact and did not contain INH. The concentration of INH in all of the three tablets were still higher than the effective bacteriostasis concentration (Isoniazid: 0.025 ~ 0.05 μg/ml) after 30 day's release in vitro. All of the tablets showed initial burst release of the INH in the early period. Drug concentration of MDST became stable and had little fluctuation starting from the 6th day of the release. Drug concentration of DST and CST decreased gradually and the rate of decrease in concentration was faster in DST than CST. MTT cytotoxicity test and direct contact test indicated that the INH-PLLA tablet had low cytotoxicity and favorable biocompatibility. Three dimensional printing technique was a reliable technique to fabricate complicated implants. Drug release pattern in MDST was the most stable among the three implants. It was

In vitro study of vancomycin release and osteoblast-like cell growth on structured calcium phosphate-collagen

International Nuclear Information System (INIS)

Pon-On, Weeraphat; Charoenphandhu, Narattaphol; Teerapornpuntakit, Jarinthorn; Thongbunchoo, Jirawan; Krishnamra, Nateetip; Tang, I-Ming

2013-01-01

A drug delivery vehicle consisting of spherical calcium phosphate-collagen particles covered by flower-like (SFCaPCol) blossoms composed of nanorod building blocks and their cellular response is studied. The spherical structure was achieved by a combination of sonication and freeze-drying. The SFCaPCol blossoms have a high surface area of approximately 280 m 2 g −1 . The blossom-like formation having a high surface area allows a drug loading efficiency of 77.82%. The release profile for one drug, vancomycin (VCM), shows long term sustained release in simulated body fluid (SBF), in a phosphate buffer saline (PBS, pH 7.4) solution and in culture media over 2 weeks with a cumulative release ∼ 53%, 75% and 50%, respectively, over the first 7 days. The biocompatibility of the VCM-loaded SFCaPCol scaffold was determined by in vitro cell adhesion and proliferation tests of rat osteoblast-like UMR-106 cells. MTT tests indicated that UMR-106 cells were viable after exposure to the VCM loaded SFCaPCol, meaning that the scaffold (the flower-like blossoms) did not impair the cell's viability. The density of cells on the substrate was seen to increase with increasing cultured time. - Graphical abstract: A spherical calcium phosphate-collagen with flower-like blossoms consisting of nanorod building blocks (SFCaPCol) particles was achieved by a combination of sonication and freeze-drying. In vitro drug release profile and the biocompatibility of the VCM-loaded SFCaPCol composite cell adhesion and proliferation in rat osteoblast-like UMR-106 cells were determined for biomaterial applications. Highlights: ► SFCaPCol and VCM-loaded SFCaPCol composite were synthesized by a combination of ultra sonication and freeze-drying. ► VCM drug-loaded SFCaPCol composite was used as substrate for the growth of rat osteoblast-like UMR-106 cells. ► Controlled release of VCM from the composite is critically medium dependent. ► The VCM-loaded SFCaPCol composite is also bioactive by in

Developing a New North American Land Cover Product at 30m Resolution: Methods, Results and Future Plans

Science.gov (United States)

Homer, C.; Colditz, R. R.; Latifovic, R.; Llamas, R. M.; Pouliot, D.; Danielson, P.; Meneses, C.; Victoria, A.; Ressl, R.; Richardson, K.; Vulpescu, M.

2017-12-01

Land cover and land cover change information at regional and continental scales has become fundamental for studying and understanding the terrestrial environment. With recent advances in computer science and freely available image archives, continental land cover mapping has been advancing to higher spatial resolution products. The North American Land Change Monitoring System (NALCMS) remains the principal provider of seamless land cover maps of North America. Founded in 2006, this collaboration among the governments of Canada, Mexico and the United States has released two previous products based on 250m MODIS images, including a 2005 land cover and a 2005-2010 land cover change product. NALCMS has recently completed the next generation North America land cover product, based upon 30m Landsat images. This product now provides the first ever 30m land cover produced for the North American continent, providing 19 classes of seamless land cover. This presentation provides an overview of country-specific image classification processes, describes the continental map production process, provides results for the North American continent and discusses future plans. NALCMS is coordinated by the Commission for Environmental Cooperation (CEC) and all products can be obtained at their website - www.cec.org.

Engineered soil covers for management of salt impacted sites

International Nuclear Information System (INIS)

Sweeney, D.A.; Tratch, D.J.

2005-01-01

The use of engineered soil cover systems to mitigate environmental impacts from tailings and waste rock piles is becoming an accepted practice. This paper presented design concepts for soil covers related to reclamation practices in the mining industry as an effective risk management practice at salt impacted sites. Research and field programs have demonstrated that a layered engineered soil cover can reduce or eliminate infiltration. Key components of the system included re-establishing surface vegetation to balance precipitation fluxes with evapotranspiration potential, and design of a capillary break below the rooting zone to minimize deeper seated infiltration. It was anticipated that the incorporation of a vegetation cover and a capillary break would minimize infiltration into the waste rock or tailing pile and reduce the generation of acid rock drainage (ARD). Design of a layered soil cover requires the incorporation of meteorological data, moisture retention characteristics of the impacted soils, and proposed engineered cover materials. Performance of the soil cover was predicted using a finite element model combined with meteorological data from the site area, unsaturated soil properties of the parent sub-surface soils and potential covered materials. The soil cover design consisted of re-vegetation and a loose clay cover overlying a compacted till layer. The design was conducted for an off site release of salt impacted pasture land adjacent to a former highway maintenance yard. The model predicted minimal infiltration during high precipitation events and no infiltration during low precipitation events. Results indicated that the proposed soil cover would enable re-establishment of a productive agricultural ground cover, as well as minimizing the potential for additional salt migration. It was concluded that further research and development is needed to ensure that the cover system is an acceptable method for long-term risk management. 17 refs., 5 figs

Minimizing employee exposure to toxic chemical releases

International Nuclear Information System (INIS)

Plummer, R.W.; Stobbe, T.J.; Mogensen, J.E.; Jeram, L.K.

1987-01-01

This book describes procedures for minimizing employee exposure to toxic chemical releases and suggested personal protective equipment (PPE) to be used in the event of such chemical release. How individuals, employees, supervisors, or companies perceive the risks of chemical exposure (risk meaning both probability of exposure and effect of exposure) determines to a great extent what precautions are taken to avoid risk. In Part I, the authors develop and approach which divides the project into three phases: kinds of procedures currently being used; the types of toxic chemical release accidents and injuries that occur; and, finally, integration of this information into a set of recommended procedures which should decrease the likelihood of a toxic chemical release and, if one does occur, will minimize the exposure and its severity to employees. Part II covers the use of personal protective equipment. It addresses the questions: what personal protective equipment ensembles are used in industry in situations where the release of a toxic or dangerous chemical may occur or has occurred; and what personal protective equipment ensembles should be used in these situations

Conceptual Design of Portable Filtered Air Suction Systems For Prevention of Released Radioactive Gas under Severe Accidents of NPP

Energy Technology Data Exchange (ETDEWEB)

Gu, Beom W.; Choi, Su Y.; Yim, Man S.; Rim, Chun T. [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of)

2014-05-15

It becomes evident that severe accidents may occur by unexpected disasters such as tsunami, heavy flood, or terror. Once radioactive material is released from NPP through severe accidents, there are no ways to prevent the released radioactive gas spreading in the air. As a remedy for this problem, the idea on the portable filtered air suction system (PoFASS) for the prevention of released radioactive gas under severe accidents was proposed. In this paper, the conceptual design of a PoFASS focusing on the number of robot fingers and robot arm rods are proposed. In order to design a flexible robot suction nozzle, mathematical models for the gaps which represent the lifted heights of extensible covers for given convex shapes of pipes and for the covered areas are developed. In addition, the system requirements for the design of the robot arms of PoFASS are proposed, which determine the accessible range of leakage points of released radioactive gas. In this paper, the conceptual designs of the flexible robot suction nozzle and robot arm have been conducted. As a result, the minimum number of robot fingers and robot arm rods are defined to be four and three, respectively. For further works, extensible cover designs on the flexible robot suction nozzle and the application of the PoFASS to the inside of NPP should be studied because the radioactive gas may be released from connection pipes between the containment building and auxiliary buildings.

Encapsulation of Volatile Citronella Essential Oil by Coacervation: Efficiency and Release Study

Science.gov (United States)

Manaf, M. A.; Subuki, I.; Jai, J.; Raslan, R.; Mustapa, A. N.

2018-05-01

The volatile citronella essential oil was encapsulated by simple coacervation and complex coacervation using Arabic gum and gelatin as wall material. Glutaraldehyde was used in the methodology as crosslinking agent. The citronella standard calibration graph obtained with R2 of 0.9523 was used for the accurate determination of encapsulation efficiency and release study. The release kinetic was analysed based on Fick"s law of diffusion for polymeric system and linear graph of Log fraction release over Log time was constructed to determine the release rate constant, k and diffusion coefficient, n. Both coacervation methods in the present study produce encapsulation efficiency around 94%. The produced capsules for both coacervation processes were discussed based on the capsules morphology and release kinetic mechanisms.

Best Dressed Test: A Study of the Covering Behavior of the Collector Urchin Tripneustes gratilla.

Directory of Open Access Journals (Sweden)

Morgan A Ziegenhorn

Full Text Available Many sea urchin genera exhibit cryptic covering behaviors. One such behavior has been documented in the sea urchin Tripneustes gratilla, and previous studies have theorized that this behavior serves as protection from UV radiation. However, other hypotheses have been presented such as protection from predators or added weight to help T. gratilla resist strong currents. A field study was conducted in October-November 2015 in Moorea, French Polynesia to assess urchin covering behavior in natural habitats. The study found that urchins partially underneath rocks covered more, and with more algae, than urchins totally underneath rocks. To test if this behavior was driven by light intensity, a series of 30-minute experimental trials were run on 10 individuals in bright and dim conditions. Individuals were given red and clear plastic, and percent cover of each was recorded. These tests were repeated once fifty percent of spines had been removed from the urchin, in order to determine whether spine loss affects T. gratilla covering behavior. The study found that urchins had a distinct preference for cover that best protects them from UV radiation. Spine loss did not significantly affect urchin ability to cover, and urchins with removed spines still preferred opaque cover. Additionally, covering behavior was mapped onto a phylogeny of echinoderms to determine how it might have evolved. Understanding urchin covering behavior more fully is a step towards an understanding of the evolution of cryptic behavior across species.

Radioactive materials released from nuclear power plants: Annual report, 1984

Energy Technology Data Exchange (ETDEWEB)

Tichler, J.; Norden, K.; Congemi, J.

1987-08-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1984 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1984 release data are summarized in tabular form. Data covering specific radionuclides are summarized.

Land Cover Classification from Multispectral Data Using Computational Intelligence Tools: A Comparative Study

Directory of Open Access Journals (Sweden)

André Mora

2017-11-01

Full Text Available This article discusses how computational intelligence techniques are applied to fuse spectral images into a higher level image of land cover distribution for remote sensing, specifically for satellite image classification. We compare a fuzzy-inference method with two other computational intelligence methods, decision trees and neural networks, using a case study of land cover classification from satellite images. Further, an unsupervised approach based on k-means clustering has been also taken into consideration for comparison. The fuzzy-inference method includes training the classifier with a fuzzy-fusion technique and then performing land cover classification using reinforcement aggregation operators. To assess the robustness of the four methods, a comparative study including three years of land cover maps for the district of Mandimba, Niassa province, Mozambique, was undertaken. Our results show that the fuzzy-fusion method performs similarly to decision trees, achieving reliable classifications; neural networks suffer from overfitting; while k-means clustering constitutes a promising technique to identify land cover types from unknown areas.

Specialists' meeting on fission product release and transport in gas-cooled reactors. Summary report

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-07-01

The purpose of the Meeting on Fission Product Release and Transport in Gas-Cooled Reactors was to compare and discuss experimental and theoretical results of fission product behaviour in gas-cooled reactors under normal and accidental conditions and to give direction for future development. The technical part of the meeting covered operational experience and laboratory research, activity release, and behaviour of released activity.

Specialists' meeting on fission product release and transport in gas-cooled reactors. Summary report

International Nuclear Information System (INIS)

1985-01-01

The purpose of the Meeting on Fission Product Release and Transport in Gas-Cooled Reactors was to compare and discuss experimental and theoretical results of fission product behaviour in gas-cooled reactors under normal and accidental conditions and to give direction for future development. The technical part of the meeting covered operational experience and laboratory research, activity release, and behaviour of released activity

Preparation, characterization, and in vitro release study of albendazole-encapsulated nanosize liposomes

Science.gov (United States)

Panwar, Preety; Pandey, Bhumika; Lakhera, P C; Singh, K P

2010-01-01

The purpose of the present study was to formulate effective and controlled release albendazole liposomal formulations. Albendazole, a hydrophobic drug used for the treatment of hydatid cysts, was encapsulated in nanosize liposomes. Rapid evaporation method was used for the preparation of albendazole-encapsulated conventional and PEGylated liposomes consisting of egg phosphatidylcholine (PC) and cholesterol (CH) in the molar ratios of (6:4) and PC:CH: polyethylene glycol (PEG) (5:4:1), respectively. In this study, PEGylated and conventional liposomes containing albendazole were prepared and their characteristics, such as particle size, encapsulation efficiency, and in vitro drug release were investigated. The drug encapsulation efficiency of PEGylated and conventional liposomes was 81% and 72%, respectively. The biophysical characterization of both conventional and PEG-coated liposomes were done by transmission electron microscopy and UV-vis spectrophotometry. Efforts were made to study in vitro release of albendazole. The drug release rate showed decrease in albendazole release in descending order: free albendazole, albendazole-loaded conventional liposomes, and least with albendazole-loaded PEG-liposomes. Biologically relevant vesicles were prepared and in vitro release of liposome-entrapped albendazole was determined. PMID:20309396

Optimization of the Area 5 Radioactive Waste Management Site Closure Cover

Energy Technology Data Exchange (ETDEWEB)

Shott, Greg; Yucel, Vefa

2009-04-01

The U.S. Department of Energy Manual DOE M 435.1-1, “Radioactive Waste Management Manual,” requires that performance assessments demonstrate that releases of radionuclides to the environment are as low as reasonably achievable (ALARA). Quantitative cost benefit analysis of radiation protection options is one component of the ALARA process. This report summarizes a quantitative cost benefit analysis of closure cover thickness for the Area 5 Radioactive Waste Management Site (RWMS) on the Nevada Test Site. The optimum cover thickness that maintains doses ALARA is shown to be the thickness with the minimum total closure cost. Total closure cost is the sum of cover construction cost and the health detriment cost. Cover construction cost is estimated based on detailed cost estimates for closure of the 92-acre Low-Level Waste Management Unit (LLWMU). The health detriment cost is calculated as the product of collective dose and a constant monetary value of health detriment in units of dollars per unit collective dose. Collective dose is the sum of all individual doses in an exposed population and has units of person-sievert (Sv). Five discrete cover thickness options ranging from 2.5 to 4.5 meters (m) (8.2 to 15 feet [ft]) are evaluated. The optimization was subject to the constraints that (1) options must meet all applicable regulatory requirements and that (2) individual doses be a small fraction of background radiation dose. Total closure cost is found to be a monotonically increasing function of cover thickness for the 92-ac LLWMU, the Northern Expansion Area, and the entire Area 5 RWMS. The cover construction cost is orders of magnitude greater than the health detriment cost. Two-thousand Latin hypercube sampling realizations of the relationship between total closure cost and cover thickness are generated. In every realization, the optimum cover thickness is 2.5 m (8.2 ft) for the 92-ac Low-Level Waste Management Unit, the Northern Expansion Area, and the entire

Optimization of the Area 5 Radioactive Waste Management Site Closure Cover

International Nuclear Information System (INIS)

Shott, Greg; Yucel, Vefa

2009-01-01

The U.S. Department of Energy Manual DOE M 435.1-1, 'Radioactive Waste Management Manual,' requires that performance assessments demonstrate that releases of radionuclides to the environment are as low as reasonably achievable (ALARA). Quantitative cost benefit analysis of radiation protection options is one component of the ALARA process. This report summarizes a quantitative cost benefit analysis of closure cover thickness for the Area 5 Radioactive Waste Management Site (RWMS) on the Nevada Test Site. The optimum cover thickness that maintains doses ALARA is shown to be the thickness with the minimum total closure cost. Total closure cost is the sum of cover construction cost and the health detriment cost. Cover construction cost is estimated based on detailed cost estimates for closure of the 92-acre Low-Level Waste Management Unit (LLWMU). The health detriment cost is calculated as the product of collective dose and a constant monetary value of health detriment in units of dollars per unit collective dose. Collective dose is the sum of all individual doses in an exposed population and has units of person-sievert (Sv). Five discrete cover thickness options ranging from 2.5 to 4.5 meters (m) (8.2 to 15 feet (ft)) are evaluated. The optimization was subject to the constraints that (1) options must meet all applicable regulatory requirements and that (2) individual doses be a small fraction of background radiation dose. Total closure cost is found to be a monotonically increasing function of cover thickness for the 92-ac LLWMU, the Northern Expansion Area, and the entire Area 5 RWMS. The cover construction cost is orders of magnitude greater than the health detriment cost. Two-thousand Latin hypercube sampling realizations of the relationship between total closure cost and cover thickness are generated. In every realization, the optimum cover thickness is 2.5 m (8.2 ft) for the 92-ac Low-Level Waste Management Unit, the Northern Expansion Area, and the entire Area

A simple assessment scheme for severe accident consequences using release parameters

Energy Technology Data Exchange (ETDEWEB)

Silva, Kampanart, E-mail: kampanarts@tint.or.th [Thailand Institute of Nuclear Technology, 16 Vibhavadi-Rangsit Rd., Latyao, Chatuchak, 10900 (Thailand); Okamoto, Koji [The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8654 (Japan)

2016-08-15

Highlights: • Nuclear accident consequence index can assess overall consequences of an accident. • Correlations between the index and release parameters are developed. • Relation between the index and release amount follows power function. • The exponent of the power function is the key to the relation. - Abstract: Nuclear accident consequence index (NACI) which can assess the overall consequences of a severe accident on people and the environment is developed based on findings from previous studies. It consists of three indices: radiation effect index, relocation index and decontamination index. Though the NACI can cover large range of consequences, its assessment requires extensive resources. The authors then attempt to simplify the assessment, by investigating the relations between the release parameters and the NACI, in order to use the release parameters for severe accident consequence assessment instead of the NACI. NACI and its components increase significantly when the release amount is increased, while the influences of the release period and the release starting time on the NACI are nearly negligible. Relations between the release amount and the NACI and its components follow simple power functions (y = ax{sup b}). The exponent of the power functions seems to be the key to the relations. The exponent of the relation between the release amount and the NACI was around 0.8–1.0 when the release amount is smaller than 100 TBq, and it increased to around 1.3–1.4 when the release amount is equal to or larger than 100 TBq.

Study on large release frequency of nuclear power plants

International Nuclear Information System (INIS)

Chen Yan; Song Wei; Li Chaojun; Fu Zhiwei; Wang Zhe; Zuo Jiaxu; Tong Jiejuan

2014-01-01

There are several definitions of large release frequency of nuclear power plant. This paper reviews the meanings of large release and requirement of large release frequency provided by IAEA, NRC and WENRA, analyses the relationship between the meanings of large release, compares the calculations of several large release frequencies, It is different frequency that the definition of LRF is not same. Last we discuss the difference between large release frequency and large early release frequency and explore the suitable definitions of LRF for nuclear power plants in China. (authors)

The Dark Energy Survey First Data Release

Science.gov (United States)

Carrasco Kind, Matias

2018-01-01

In this talk I will announce and highlight the main components of the first public data release (DR1) coming from the Dark Energy Survey (DES).In January 2016, the DES survey made available, in a simple unofficial release to the astronomical community, the first set of products. This data was taken and studied during the DES Science Verification period consisting on roughly 250 sq. degrees and 25 million objects at a mean depth of i=23.7 that led to over 80 publications from DES scientist.The DR1 release is the first official release from the main survey and it consists on the observations taken during the first 3 seasons from August 2013 to February 2016 (about 100 nights each season) of the survey which cover the entire DES footprint. All of the Single Epoch Images and the Year 3 Coadded images distributed in 10223 tiles are available for download in this release. The catalogs provide astrometry, photometry and basic classification for near 400M objects in roughly 5000 sq. degrees on the southern hemisphere with a approximate mean depth of i=23.3. Complementary footprint, masking and depth information is also available. All of the software used during the generation of these products are open sourced and have been made available through the Github DES Organization. Images, data and other sub products have been possible through the international and collaborative effort of all 25 institutions involved in DES and are available for exploration and download through the interfaces provided by a partnership between NCSA, NOAO and LIneA.

Chemical composition of overland flow produced on soils covered with vegetative ash

Directory of Open Access Journals (Sweden)

M.B. Bodí

2013-05-01

Full Text Available The objective of this study was to ascertain the differences between the soluble elements of ash obtained under laboratory conditions and the dissolved in overland flow from soils covered with a layer of ash. The overland flow was obtained during series of rainfall simulations over soils covered with two different types of ash. This study indicates that the soluble elements released from ash can modify water quality increasing its pH, electrical conductivity and especially cation content. The nutrients solubilised are not necessarily the same as the elemental composition of ash itself. Runoff composition depends on the volume of water produced, on the solubility of the ash components and on the chemical interactions with water from rainfall and soil. After the first intense rain event, most of the elements are solubilised and lixiviated or washed out, however, some of them may increase in the runoff or soil water some weeks later due to chemical interactions with water from rainfall and soil nutrients.

Radiological considerations of the reactor cover gas processing system at the FFTF

International Nuclear Information System (INIS)

Prevo, P.R.

1987-01-01

Radiological and environmental protection experience associated with the reactor cover gas processing system at the Fast Flux Test Facility (FFTF) has been excellent. Personnel radiation exposures received from operating and maintaining the reactor cover gas processing system have been very low, the system has remained free of radioactive particulate contamination through the first seven operating cycles (cesium contamination was detected at the end of Cycle 8A), and releases of radioactivity to the environment have been very low, well below environmental standards. This report discusses these three aspects of fast reactor cover gas purification over the first eight operating cycles of the FFTF (a duration of a little more than four years, from April 1982 through July 1986). (author)

Design and Installation of a Disposal Cell Cover Field Test

Energy Technology Data Exchange (ETDEWEB)

Benson, C.H. [University of Wisconsin–Madison, Madison, Wisconsin; Waugh, W.J. [S.M. Stoller Corporation, Grand Junction, Colorado; Albright, W.H. [Desert Research Institute, Reno, Nevada; Smith, G.M. [Geo-Smith Engineering, Grand Junction, Colorado; Bush, R.P. [U.S. Department of Energy, Grand Junction, Colorado

2011-02-27

The U.S. Department of Energy’s Office of Legacy Management (LM) initiated a cover assessment project in September 2007 to evaluate an inexpensive approach to enhancing the hydrological performance of final covers for disposal cells. The objective is to accelerate and enhance natural processes that are transforming existing conventional covers, which rely on low-conductivity earthen barriers, into water balance covers, that store water in soil and release it as soil evaporation and plant transpiration. A low conductivity cover could be modified by deliberately blending the upper layers of the cover profile and planting native shrubs. A test facility was constructed at the Grand Junction, Colorado, Disposal Site to evaluate the proposed methodology. The test cover was constructed in two identical sections, each including a large drainage lysimeter. The test cover was constructed with the same design and using the same materials as the existing disposal cell in order to allow for a direct comparison of performance. One test section will be renovated using the proposed method; the other is a control. LM is using the lysimeters to evaluate the effectiveness of the renovation treatment by monitoring hydrologic conditions within the cover profile as well as all water entering and leaving the system. This paper describes the historical experience of final covers employing earthen barrier layers, the design and operation of the lysimeter test facility, testing conducted to characterize the as-built engineering and edaphic properties of the lysimeter soils, the calibration of instruments installed at the test facility, and monitoring data collected since the lysimeters were constructed.

Effects of modified surfaces produced at plasma-facing surface on hydrogen release behavior in the LHD

Directory of Open Access Journals (Sweden)

Y. Nobuta

2017-08-01

Full Text Available In the present study, an additional deuterium (D ion irradiation was performed against long-term samples mounted on the helical coil can and in the outer private region in the LHD during the 17th experimental campaign. Based on the release behavior of the D and hydrogen (H retained during the experimental campaign, the difference of release behavior at the top surface and in bulk of modified surfaces is discussed. Almost all samples on the helical coil can were erosion-dominant and some samples were covered with boron or carbon, while a very thick carbon films were formed in the outer private region. In the erosion-dominant area, the D desorbed at much lower temperatures compared to that of H retained during the LHD plasma operation. For the samples covered with boron, the D tended to desorb at lower temperatures compared to H. For the carbon deposition samples, the D desorbed at much higher temperatures compared to no deposition and boron-covered samples, which was very similar to that of H. The D retention capabilities at the top surface of carbon and boron films were 2–3 times higher than no deposition area. The results indicate that the retention and release behavior at the top surface of the modified layer can be different from that of bulk substrate material.

Results of ten years study of Chernobyl NPP release fallout properties and behaviour in soils

International Nuclear Information System (INIS)

Ivanov, Yu.; Kashparov, V.A.; Levchuk, S.; Protsak, V.; Zvaritch, S.; Khomutinin, Yu.; Oreshich, L.

1997-01-01

Radioactive contamination of territories of Ukrainian and Byelorussian Polesye as a result of ChNPP accidental release is characterized by high level of un-homogenity of fallout properties (physico-chemical properties, radionuclide composition etc.), density of the territory contamination by long-lived radionuclides. On the other hand, the soil-plant cover of contaminated territory is presented by large set of soils, characterized by contrast physico-chemical and water-physical properties. Peculiarities of the behavior of different radionuclides, represented initially by various components of radioactive fallout, in soils, as a first link of migration chains are considered

488-D Ash Basin Vegetative Cover Treatibility Study

Energy Technology Data Exchange (ETDEWEB)

Barton, Christopher; Marx, Don; Blake, John; Adriano, Domy; Koo, Bon-Jun; Czapka, Stephen

2003-01-01

The 488-D Ash Basin is an unlined containment basin that received ash and coal reject material from the operation of a powerhouse at the USDOE's Savannah River Site, SC. They pyretic nature of the coal rejects has resulted in the formation of acidic drainage (AD), which has contributed to groundwater deterioration and threatens biota in down gradient wetlands. Establishment of a vegetative cover was examined as a remedial alternative for reducing AD generation within this system by enhanced utilization of rainwater and subsequent non-point source water pollution control. The low nutrient content, high acidity, and high salinity of the basin material, however, was deleterious to plant survivability. As such, studies to identify suitable plant species and potential adaptations, and pretreatment techniques in the form of amendments, tilling, and/or chemical stabilization were needed. A randomized block design consisting of three subsurface treatments (blocks) and five duplicated surface amendments (treatments) was developed. One hundred inoculated pine trees were planted on each plot. Herbaceous species were also planted on half of the plots in duplicated 1-m2 beds. After two growing seasons, deep ripping, subsurface amendments and surface covers were shown to be essential for the successful establishment of vegetation on the basin. This is the final report of the study.

Revised guidance on reporting of offshore hydrocarbon releases

International Nuclear Information System (INIS)

1996-11-01

The application offshore of the Reporting of Injuries, Disease and Dangerous Occurrences Regulations 1995 (RIDDOR 1995) has resulted in a new statutory reporting form. The definitions in RIDDOR 95 covering offshore hydrocarbon releases have been slightly revised, making it necessary to revise the guidance on reporting of offshore hydrocarbon releases. RIDDOR 1995 does not affect the existing voluntary arrangements for completion of forms. The receipt of correctly completed forms is important to ensure good output data from the database, and the guidance contained in this document is therefore aimed at assisting completion of the voluntary form. (UK)

Static and mobile networks design for atmospheric accidental releases monitoring

International Nuclear Information System (INIS)

Abida, R.

2010-01-01

The global context of my PhD thesis work is the optimization of air pollution monitoring networks, but more specifically it concerns the monitoring of accidental releases of radionuclides in air. The optimization problem of air quality measuring networks has been addresses in the literature. However, it has not been addresses in the context of surveillance of accidental atmospheric releases. The first part of my thesis addresses the optimization of a permanent network of monitoring of radioactive aerosols in the air, covering France. The second part concerns the problem of targeting of observations in case of an accidental release of radionuclides from a nuclear plant. (author)

Mean species cover: a harmonized indicator of shrub cover for forest inventories

Science.gov (United States)

Iciar Alberdi; Sonia Condés; Ronald E. Mcroberts; Susanne Winter

2018-01-01

Because shrub cover is related to many forest ecosystem functions, it is one of the most relevant variables for describing these communities. Nevertheless, a harmonized indicator of shrub cover for large-scale reporting is lacking. The aims of the study were threefold: to define a shrub indicator that can be used by European countries for harmonized shrub cover...

Development of drainage water quality from a landfill cover built with secondary construction materials.

Science.gov (United States)

Travar, Igor; Andreas, Lale; Kumpiene, Jurate; Lagerkvist, Anders

2015-01-01

The aim of this study was to evaluate the drainage water quality from a landfill cover built with secondary construction materials (SCM), fly ash (FA), bottom ash (BA) sewage sludge, compost and its changes over time. Column tests, physical simulation models and a full scale field test were conducted. While the laboratory tests showed a clear trend for all studied constituents towards reduced concentrations over time, the concentrations in the field fluctuated considerably. The primary contaminants in the drainage water were Cl(-), N, dissolved organic matter and Cd, Cu, Ni, Zn with initial concentrations one to three orders of magnitude above the discharge values to the local recipient. Using a sludge/FA mixture in the protection layer resulted in less contaminated drainage water compared to a sludge/BA mixture. If the leaching conditions in the landfill cover change from reduced to oxidized, the release of trace elements from ashes is expected to last about one decade longer while the release of N and organic matter from the sludge can be shortened with about two-three decades. The observed concentration levels and their expected development over time require drainage water treatment for at least three to four decades before the water can be discharged directly to the recipient. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

A study of chitosan hydrogel with embedded mesoporous silica nanoparticles loaded by ibuprofen as a dual stimuli-responsive drug release system for surface coating of titanium implants.

Science.gov (United States)

Zhao, Pengkun; Liu, Hongyu; Deng, Hongbing; Xiao, Ling; Qin, Caiqin; Du, Yumin; Shi, Xiaowen

2014-11-01

In this study, the complex pH and electro responsive system made of chitosan hydrogel with embedded mesoporous silica nanoparticles (MSNs) was evaluated as a tunable drug release system. As a model drug, ibuprofen (IB) was used; its adsorption in MSNs was evidenced by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and thermogravimetric analysis (TG). In order to prepare the complex drug release system, the loaded particles IB-MSNs were dispersed in chitosan solution and then the complex IB-MSNs/chitosan film of 2mm thickness was deposited as a hydrogel on the titanium electrode. The codeposition of components was performed under a negative biasing of the titanium electrode at -0.75 mA/cm2 current density during 30 min. The IB release from the IB-MSNs/chitosan hydrogel film was studied as dependent on pH of the release media and electrical conditions applied to the titanium plate. When incubating the complex hydrogel film in buffers with different pH, the IB release followed a near zero-order profile, though its kinetics varied. Compared to the spontaneous IB release from the hydrogel in 0.9% NaCl solution (at 0 V), the application of negative biases to the coated titanium plate had profound effluences on the release behavior. The release was retarded when -1.0 V was applied, but a faster kinetics was observed at -5.0 V. These results imply that a rapid, mild and facile electrical process for covering titanium implants by complex IB-MSNs/chitosan hydrogel films can be used for controlled drug delivery applications. Copyright © 2014 Elsevier B.V. All rights reserved.

Usability Study to Assess the IGBP Land Cover Classification for Singapore

Directory of Open Access Journals (Sweden)

Nanki Sidhu

2017-10-01

Full Text Available Our research focuses on assessing the usability of the International Geosphere Biosphere Programme (IGBP classification scheme provided in the MODIS MCD12Q1-1 dataset for assessing the land cover of the city-state, Singapore. We conducted a user study with responses from 33 users by providing them with Google Earth images from different parts of Singapore, asking survey-takers to classify these images according to their understanding by the IGBP definitions provided. We also conducted interviews with experts from major governmental agencies working with satellite imagery, which highlighted the need for a detailed land classification for Singapore. In addition to the qualitative analysis of the IGBP land classification scheme, we carried out a validation of the MCD12Q1-1 remote sensing product against SPOT-5 imagery for our study area. The user study revealed that survey-takers were able to correctly classify urban areas, as well as densely forested areas. Misclassifications between Cropland and Mixed Forest classes were highest and were attributed by users to the broad terminology of the IGBP of the two land cover class definitions. For the accuracy assessment, we obtained validation points using weighted and unweighted stratified sampling. The overall classification accuracy for all 17 IGBP land classes is 62%. Upon selecting only the four most occurring IGBP land classes in Singapore, the classification accuracy improved to 71%. Validation of the MCD12Q1-1 against ground truth for Singapore revealed less-common land classes that may be of importance in a global context but are sources of error when the same product is applied at a smaller scale. Combining the user study with the accuracy assessment gives a comprehensive overview of the challenges associated with using global-level land cover data to derive localized land cover information specifically for smaller land masses like Singapore.

Kinetic release studies of nitrogen-containing bisphosphonate fromgum acacia crosslinked hydrogels

CSIR Research Space (South Africa)

Aderibigbe, BA

2014-11-01

Full Text Available on the release mechanism of nitrogen-containing bisphosphonate (BP) wasstudied at pH 1.2 and 7.4. The hydrogels exhibited high swelling ratios at pH 7.4 and low swelling ratiosat pH 1.2. The release study was performed using UV–Visible spectroscopy via complex...

UV imaging for in vitro dissolution and release studies: Initial experiences

DEFF Research Database (Denmark)

Østergaard, Jesper; Lenke, James; Jensen, Sabrine Smedegaard

2014-01-01

UV imaging has recently been introduced as a method in drug dissolution and release testing. Spatially and temporally resolved mapping of drug oncentrations in a 7 × 9 mm imaging area provides new opportunities for visualization and study of drug dissolution and release. This review describes...... in hydrogels with relevance for characterization of parenteral depots. UV imaging may be of particular use when the amounts of material are sparse and detailed insights into dissolution and release processes are required, that is in solid form screening, preformulation, and early drug development....

Monitoring land use/land cover changes using CORINE land cover data: a case study of Silivri coastal zone in Metropolitan Istanbul.

Science.gov (United States)

Yilmaz, Rüya

2010-06-01

The objective of the present study was to assess changes in land use/land cover patterns in the coastal town of Silivri, a part of greater Istanbul administratively. In the assessment, remotely sensed data, in the form of satellite images, and geographic information systems were used. Types of land use/land cover were designated as the percentage of the total area studied. Results calculated from the satellite data for land cover classification were compared successfully with the database Coordination of Information on the Environment (CORINE). This served as a reference to appraise the reliability of the study presented here. The CORINE Program was established by the European Commission to create a harmonized Geographical Information System on the state of the environment in the European Community. Unplanned urbanization is causing land use changes mainly in developing countries such as Turkey. This situation in Turkey is frequently observed in the city of Istanbul. There are only a few studies of land use-land cover changes which provide an integrated assessment of the biophysical and societal causes and consequences of environmental degradation in Istanbul. The research area comprised greater Silivri Town which is situated by the coast of Marmara Sea, and it is located approximately 60 km west of Istanbul. The city of Istanbul is one of the largest metropolises in Europe with ca. 15 million inhabitants. Additionally, greater Silivri is located near the terminal point of the state highway connecting Istanbul with Europe. Measuring of changes occurring in land use would help control future planning of settlements; hence, it is of importance for the Greater Silivri and Silivri Town. Following our evaluations, coastal zone of Silivri was classified into the land use groups of artificial surfaces agricultural areas and forests and seminatural areas with 47.1%, 12.66%, and 22.62%, respectively.

Code of practice for the release of hydrostatic test water from hydrostatic testing of petroleum liquid and gas pipelines

International Nuclear Information System (INIS)

1999-01-01

This booklet describes a series of administrative procedures regarding the code of practice in Alberta for the release of hydrostatic test water from hydrostatic testing of petroleum liquid and gas pipelines. The topics covered include the registration process, the type and quality of water to use during the test, and the analytical methods to be used. Reporting schedule and record keeping information are also covered. Schedule 1 discusses the requirements for the release of hydrostatic test water to land, while Schedule 2 describes the requirements for the release of hydrostatic test water to receiving water. 3 tabs

Car Covers | Outdoor Covers Canada

OpenAIRE

Covers, Outdoor

2018-01-01

Protect your car from the elements with Ultimate Touch Car Cover. The multi-layer non-woven fabric is soft on the finish and offers 4 seasons all weather protection.https://outdoorcovers.ca/car-covers/

Case study of a full-scale evapotranspiration cover

Science.gov (United States)

McGuire, Patrick E.; Andraski, Brian J.; Archibald, Ryan E.

2009-01-01

The design, construction, and performance analyses of a 6.1ha evapotranspiration (ET) landfill cover at the semiarid U.S. Army Fort Carson site, near Colorado Springs, Colo. are presented. Initial water-balance model simulations, using literature reported soil hydraulic data, aided selection of borrow-source soil type(s) that resulted in predictions of negligible annual drainage (⩽1mm∕year). Final construction design was based on refined water-balance simulations using laboratory determined soil hydraulic values from borrow area natural soil horizons that were described with USDA soil classification methods. Cover design components included a 122cmthick clay loam (USDA), compaction ⩽80% of the standard Proctor maximum dry density (dry bulk density ∼1.3Mg∕m3), erosion control measures, top soil amended with biosolids, and seeding with native grasses. Favorable hydrologic performance for a 5year period was documented by lysimeter-measured and Richards’-based calculations of annual drainage that were all <0.4mm∕year. Water potential data suggest that ET removed water that infiltrated the cover and contributed to a persistent driving force for upward flow and removal of water from below the base of the cover.

Controlled drug release on amine functionalized spherical MCM-41

International Nuclear Information System (INIS)

Szegedi, Agnes; Popova, Margarita; Goshev, Ivan; Klébert, Szilvia; Mihály, Judit

2012-01-01

MCM-41 silica with spherical morphology and small particle sizes (100 nm) was synthesized and modified by post-synthesis method with different amounts of 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, was carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N 2 physisorption, elemental analysis, thermal analysis and FT-IR spectroscopy. A new method was developed for the quantitative determination of amino groups in surface modified mesoporous materials by the ninhydrin reaction. Good correlation was found between the amino content of the MCM-41 materials determined by the ninhydrin method and their ibuprofen adsorption capacity. Amino modification resulted in high degree of ibuprofen loading and slow release rate in comparison to the parent non-modified MCM-41. - Graphical abstract: Determination of surface amino groups by ninhidrin method. Highlights: ► Spherical MCM-41 modified by different amounts of APTES was studied. ► Ibuprofen (IBU) adsorption and release characteristics was tested. ► The ninhydrin reaction was used for the quantitative determination of amino groups. ► Stoichiometric amount of APTES is enough for totally covering the surface with amino groups. ► Good correlation was found between the amino content and IBU adsorption capacity.

Investigation of accuracy of CORINE 2006 land cover data used in watershed studies

Directory of Open Access Journals (Sweden)

Ayhan Ateşoğlu

2016-01-01

Full Text Available There have been many studies concerning the use of sustainable natural resources. The planning concerning the results of watershed-based studies is made for the future. The issue to be considered in these studies, is obtaining accurate data. The most important data of the studies in the watershed basin is obtaining land cover/use data. Land cover / land classification done by using remote sensing and GIS and monitoring the change periodically are both easy and economical. To this end, CORINE (Coordination of Information on the Environment land cover program was initiated by The European Commission (CEC. The accuracy of CORINE 2006 land cover data was evaluated using high resolution Google Earth data in two separate test areas located in the Black Sea and Central Anatolia region. Random 5000 points for each test area were assigned to classes according to the CORINE classification method using Google Earth and were compared with the CORINE 2006 data. The accuracy of first test area in Black Sea region was calculated as 51.80% the accuracy of second test area in Central Anatolia region was calculated as 55.32%. For each test area, CORINE 2006 data has not been found to be up to date and has been detected to have low accuracy.

The comparison between limited open carpal tunnel release using direct vision and tunneling technique and standard open carpal tunnel release: a randomized controlled trial study.

Science.gov (United States)

Suppaphol, Sorasak; Worathanarat, Patarawan; Kawinwongkovit, Viroj; Pittayawutwinit, Preecha

2012-04-01

To compare the operative outcome of carpal tunnel release between limited open carpal tunnel release using direct vision and tunneling technique (group A) with standard open carpal tunnel release (group B). Twenty-eight patients were enrolled in the present study. A single blind randomized control trial study was conducted to compare the postoperative results between group A and B. The study parameters were Levine's symptom severity and functional score, grip and pinch strength, and average two-point discrimination. The postoperative results between two groups were comparable with no statistical significance. Only grip strength at three months follow up was significantly greater in group A than in group B. The limited open carpal tunnel release in the present study is effective comparable to the standard open carpal tunnel release. The others advantage of this technique are better cosmesis and improvement in grip strength at the three months postoperative period.

Real time in vitro studies of doxorubicin release from PHEMA nanoparticles

Directory of Open Access Journals (Sweden)

Bajpai AK

2009-10-01

Full Text Available Abstract Background Many anticancer agents have poor water solubility and therefore the development of novel delivery systems for such molecules has received significant attention. Nanocarriers show great potential in delivering therapeutic agents into the targeted organs or cells and have recently emerged as a promising approach to cancer treatments. The aim of this study was to prepare and use poly-2-hydroxyethyl methacrylate (PHEMA nanoparticles for the controlled release of the anticancer drug doxorubicin. Results PHEMA nanoparticles have been synthesized and characterized using FTIR and scanning electron microscopy (SEM, particle size analysis and surface charge measurements. We also studied the effects of various parameters such as percent loading of drugs, chemical architecture of the nanocarriers, pH, temperature and nature of the release media on the release profiles of the drug. The chemical stability of doxorubicin in PBS was assessed at a range of pH. Conclusion Suspension polymerization of 2-hydroxyethyl methacrylate (HEMA results in the formation of swellable nanoparticles of defined composition. PHEMA nanoparticles can potentially be used for the controlled release of the anticancer drug doxorubicin.

Study of the radon released from open drill holes

International Nuclear Information System (INIS)

Pacer, J.C.

1981-06-01

The radon emanating from three open drill holes was measured at a site of known uranium mineralization in the Red Desert of south central Wyoming. The radon flux from the soil and drill holes was measured by the accumulator method with activated charcoal cartridges. The surface soil was found to release radon at an average rate of 0.41 atoms/cm 2 /sec; the radon emanating from the holes was more variable than that from the soil. The three holes studied released an average of 47 atoms/cm 2 /sec of radon. This average is equivalent to the radon released to the atmosphere by 14.5 ft 2 of soil. The data indicate that the radon emanated from an open drill hole is not as significant as other possible activities at a drill site (i.e. digging a trench or drilling a hole) or from household activities involving the usage of water

Organosilane functionalization of halloysite nanotubes for enhanced loading and controlled release

International Nuclear Information System (INIS)

Yuan Peng; Southon, Peter D; Kepert, Cameron J; Liu Zongwen

2012-01-01

The surfaces of naturally occurring halloysite nanotubes were functionalized with γ-aminopropyltriethoxysilane (APTES), which was found to have a substantial effect on the loading and subsequent release of a model dye molecule. APTES was mostly anchored at the internal lumen surface of halloysite through covalent grafting, forming a functionalized surface covered by aminopropyl groups. The dye loading of the functionalized halloysite was 32% greater than that of the unmodified sample, and the release from the functionalized halloysite was dramatically prolonged as compared to that from the unmodified one. Dye release was prolonged at low pH and the release at pH 3.5 was approximately three times slower than that at pH 10.0. These results demonstrate that organosilane functionalization makes pH an external trigger for controlling the loading of guest on halloysite and the subsequent controlled release. (paper)

Organosilane functionalization of halloysite nanotubes for enhanced loading and controlled release.

Science.gov (United States)

Yuan, Peng; Southon, Peter D; Liu, Zongwen; Kepert, Cameron J

2012-09-21

The surfaces of naturally occurring halloysite nanotubes were functionalized with γ-aminopropyltriethoxysilane (APTES), which was found to have a substantial effect on the loading and subsequent release of a model dye molecule. APTES was mostly anchored at the internal lumen surface of halloysite through covalent grafting, forming a functionalized surface covered by aminopropyl groups. The dye loading of the functionalized halloysite was 32% greater than that of the unmodified sample, and the release from the functionalized halloysite was dramatically prolonged as compared to that from the unmodified one. Dye release was prolonged at low pH and the release at pH 3.5 was approximately three times slower than that at pH 10.0. These results demonstrate that organosilane functionalization makes pH an external trigger for controlling the loading of guest on halloysite and the subsequent controlled release.

Radioactive materials released from nuclear power plants. Annual report, 1982. Volume 3

International Nuclear Information System (INIS)

Tichler, J.; Norden, K.

1986-02-01

Releases of radioactive materials in airborne and liquid effluents from commercial light water reactors during 1982 have been compiled and reported. Data on solid waste shipments as well as selected operating information have been included. This report supplements earlier annual reports issued by the former Atomic Energy Commission and the Nuclear Regulatory Commission. The 1982 release data are summarized in tabular form. Data covering specific radionuclides are summarized

Site Release Report for C-Well Pipeline, UE-25 Large Rocks Test Site, and 29 GSF Test Pits

International Nuclear Information System (INIS)

K.E. Rasmuson

2002-01-01

The U.S. Department of Energy has implemented a program to reclaim lands disturbed by site characterization at Yucca Mountain. Long term goals of the program are to re-establish processes on disturbed sites that will lead to self-sustaining plant communities. The Biological Opinion for Yucca Mountain Site Characterization Studies required that the U.S. Department of Energy develop a Reclamation Standards and Monitoring Plan to evaluate the success of reclamation efforts. According to the Reclamation Standards and Monitoring Plan, reclaimed sites will be monitored periodically, remediated if necessary, and eventually compared to an appropriate reference area to determine whether reclamation goals have been achieved and the site can be released from further monitoring. Plant cover, density, and species richness (success parameters) on reclaimed sites are compared to 60 percent of the values (success criteria) for the same parameters on the reference area. Small sites (less than 0.1 ha) are evaluated for release using qualitative methods while large sites (greater than 0.1 ha) are evaluated using quantitative methods. In the summer of 2000, 31 small sites reclaimed in 1993 and 1994 were evaluated for reclamation success and potential release from further monitoring. Plant density, cover, and species richness were estimated on the C-Well Pipeline, UE-25 Large Rocks test site, and 29 ground surface facility test pits. Evidence of erosion, reproduction and natural recruitment, exotic species abundance, and animal use (key attributes) also were recorded for each site and used in success evaluations. The C-Well Pipeline and ground surface facility test pits were located in a ''Larrea tridentata - Ephedra nevadensis'' vegetation association while the UE-25 Large Rocks test site was located in an area dominated by ''Coleogyne ramosissima and Ephedra nevadensis''. Reference areas in the same vegetation associations with similar slope and aspect were chosen for comparison to

Site Release Reports for C-Well Pipeline, UE-25 Large Rocks Test Site, and 29 GSF Test Pits

Energy Technology Data Exchange (ETDEWEB)

K.E. Rasmuson

2002-04-02

The U.S. Department of Energy has implemented a program to reclaim lands disturbed by site characterization at Yucca Mountain. Long term goals of the program are to re-establish processes on disturbed sites that will lead to self-sustaining plant communities. The Biological Opinion for Yucca Mountain Site Characterization Studies required that the U.S. Department of Energy develop a Reclamation Standards and Monitoring Plan to evaluate the success of reclamation efforts. According to the Reclamation Standards and Monitoring Plan, reclaimed sites will be monitored periodically, remediated if necessary, and eventually compared to an appropriate reference area to determine whether reclamation goals have been achieved and the site can be released from further monitoring. Plant cover, density, and species richness (success parameters) on reclaimed sites are compared to 60 percent of the values (success criteria) for the same parameters on the reference area. Small sites (less than 0.1 ha) are evaluated for release using qualitative methods while large sites (greater than 0.1 ha) are evaluated using quantitative methods. In the summer of 2000, 31 small sites reclaimed in 1993 and 1994 were evaluated for reclamation success and potential release from further monitoring. Plant density, cover, and species richness were estimated on the C-Well Pipeline, UE-25 Large Rocks test site, and 29 ground surface facility test pits. Evidence of erosion, reproduction and natural recruitment, exotic species abundance, and animal use (key attributes) also were recorded for each site and used in success evaluations. The C-Well Pipeline and ground surface facility test pits were located in a ''Larrea tridentata - Ephedra nevadensis'' vegetation association while the UE-25 Large Rocks test site was located in an area dominated by ''Coleogyne ramosissima and Ephedra nevadensis''. Reference areas in the same vegetation associations with similar slope

Releases of natural enemies in Hawaii since 1980 for classical biological control of weeds

Science.gov (United States)

P. Conant; J. N. Garcia; M. T. Johnson; W. T. Nagamine; C. K. Hirayama; G. P. Markin; R. L. Hill

2013-01-01

A comprehensive review of biological control of weeds in Hawaii was last published in 1992, covering 74 natural enemy species released from 1902 through 1980. The present review summarizes releases of 21 natural enemies targeting seven invasive weeds from 1981 to 2010. These projects were carried out by Hawaii Department of Agriculture (HDOA), USDA Forest Service (USFS...

MECHANISMS CONTROLLING Ca ION RELEASE FROM SOL-GEL DERIVED IN SITU APATITE-SILICA NANOCOMPOSITE POWDER

Directory of Open Access Journals (Sweden)

Seyed Mohsen Latifi

2015-03-01

Full Text Available Ca ion release from bioactive biomaterials could play an important role in their bioactivity and osteoconductivity properties. In order to improve hydroxyapatite (HA dissolution rate, in situ apatite-silica nanocomposite powders with various silica contents were synthesized via sol-gel method and mechanisms controlling the Ca ion release from them were investigated. Obtained powders were characterized by X-ray diffraction (XRD and transmission electron spectroscopy (TEM techniques, acid dissolution test, and spectroscopy by atomic absorption spectrometer (AAS. Results indicated the possible incorporation of (SiO44- into the HA structure and tendency of amorphous silica to cover the surface of HA particles. However, 20 wt. % silica was the lowest amount that fully covered HA particles. All of the nanocomposite powders showed more Ca ion release compared with pure HA, and HA - 10 wt. % silica had the highest Ca ion release. The crystallinity, the crystallite size, and the content of HA, along with the integrity, thickness, and ion diffusion possibility through the amorphous silica layer on the surface of HA, were factors that varied due to changes in the silica content and were affected the Ca ion release from nanocomposite powders.

Outrage Factors in Government Press Releases of Food Risk and Their Influence on News Media Coverage.

Science.gov (United States)

Ju, Youngkee; Lim, Jeongsub; Shim, Minsun; You, Myoungsoon

2015-08-01

An appropriate level of risk perception should be a critical issue in modern "risk society." There have been many studies on the influences on risk perception. This study investigates whether risk communication scholar Dr. Peter Sandman's outrage factors intensify journalistic attention to health risks from food consumption. A content analysis of a health institution's press releases was conducted to examine 15 outrage factors of food risks conveyed in the governmental risk communication. In addition, the news stories covering the food risks informed by the press releases were calculated to evaluate the relation between outrage factors of a risk and the number of news stories covering the risk. Results showed that controllability was the most salient outrage factor, followed by trust, voluntariness, familiarity, and human origin; the greater the outrage score of a risk, the more news stories of the risk. For individual outrage factors, a risk with an implication of catastrophic potential was associated with an increase of news stories. Food providers' distrustful behaviors also influenced journalistic attention to the food risks. The implication of the findings to health message designers is discussed.

Study of firedamp release in sub-level caving

Energy Technology Data Exchange (ETDEWEB)

Castano, F.S.; Sanz Delgado, M.A.; Iturriaga Trenor, S.; Alberdi Vinas, C.

1988-01-01

The field work developed in the pits of 'Hullera Vasco-Leonesa' in Santa Lucia (Leon) to control firedamp release is described. Conclusions obtained concerning gas emission, irregularity and firedamp balance in sub-level caving winning faces are discussed. Some definitions of basic concepts in firedamp studies are also included. 7 figs.

Reduction of acid rock drainage using steel slag in cover systems over sulfide rock waste piles.

Science.gov (United States)

de Almeida, Rodrigo Pereira; Leite, Adilson do Lago; Borghetti Soares, Anderson

2015-04-01

The extraction of gold, coal, nickel, uranium, copper and other earth-moving activities almost always leads to environmental damage. In metal and coal extraction, exposure of sulfide minerals to the atmosphere leads to generation of acid rock drainage (ARD) and in underground mining to acid mine drainage (AMD) due to contamination of infiltrating groundwater. This study proposes to develop a reactive cover system that inhibits infiltration of oxygen and also releases alkalinity to increase the pH of generated ARD and attenuate metal contaminants at the same time. The reactive cover system is constructed using steel slag, a waste product generated from steel industries. This study shows that this type of cover system has the potential to reduce some of the adverse effects of sulfide mine waste disposal on land. Geochemical and geotechnical characterization tests were carried out. Different proportions of sulfide mine waste and steel slag were studied in leachate extraction tests. The best proportion was 33% of steel slag in dry weight. Other tests were conducted as follows: soil consolidation, saturated permeability and soil water characteristic curve. The cover system was numerically modeled through unsaturated flux analysis using Vadose/w. The solution proposed is an oxygen transport barrier that allows rain water percolation to treat the ARD in the waste rock pile. The results showed that the waste pile slope is an important factor and the cover system must have 5 m thickness to achieve an acceptable effectiveness. © The Author(s) 2015.

Hydrograph sensitivity to estimates of map impervious cover: a WinHSPF BASINS case study

Science.gov (United States)

Endreny, Theodore A.; Somerlot, Christopher; Hassett, James M.

2003-04-01

The BASINS geographic information system hydrologic toolkit was designed to compute total maximum daily loads, which are often derived by combining water quantity estimates with pollutant concentration estimates. In this paper the BASINS toolkit PLOAD and WinHSPF sub-models are briefly described, and then a 0·45 km2 headwater watershed in the New York Croton River area is used for a case study illustrating a full WinHSPF implementation. The goal of the Croton study was to determine the sensitivity of WinHSPF hydrographs to changes in land cover map inputs. This scenario occurs when scaling the WinHSPF model from the smaller 0·45 km2 watershed to the larger 1000 km2 management basin of the entire Croton area. Methods used to test model sensitivity include first calibrating the WinHSPF hydrograph using research-monitored precipitation and discharge data together with high spatial resolution and accuracy land cover data of impervious and pervious areas, and then swapping three separate land cover files, known as GIRAS, MRLC, and DOQQ data, into the calibrated model. Research results indicated that the WinHSPF land cover swapping had peak flow sensitivity in December 2001 hydrographs between 35% underestimation and 20% overestimation, and that errors in land-cover-derived runoff ratios for storm totals and peak flows tracked with the land cover data estimates of impervious area.

Parametric study of sodium aerosols in the cover-gas space of sodium-cooled reactors

International Nuclear Information System (INIS)

Sheth, A.

1975-03-01

A mathematical model has been developed to describe the behavior of sodium aerosols in the cover-gas space of a sodium-cooled reactor. A review of the literature was first made to examine methods of aerosol generation, mathematical expressions representing aerosol behavior, and pertinent experimental investigations of sodium aerosols. In the development of the model, some terms were derived from basic principles and other terms were estimated from available correlations. The model was simulated on a computer, and important parameters were studied to determine their effects on the overall behavior of sodium aerosols. The parameters studied were sodium pool temperature, source and initial size of particles, film thickness at the sodium pool/cover gas interface, wall plating parameters, cover-gas flow rate, and type of cover gas (argon and helium). The model satisfactorily describes the behavior of sodium aerosol in argon, but not in helium. Possible reasons are given for the failure of the model with helium, and further experimental work is recommended. The mathematical model, with appropriate modifications to describe the behavior of sodium aerosols in helium, would be very useful in designing traps to remove aerosols from the cover gas of sodium-cooled reactors. (U.S.)

Measured tritium in groundwater related to atmospheric releases from the Marcoule nuclear site

International Nuclear Information System (INIS)

Levy, F.; Clech, A.; Crochet, P.

1996-01-01

Tritium is released into the atmosphere during normal operation from the industrial facilities operated by COGEMA at Marcoule; over a 1 5-year period covered by this study (1979-1994) the quantities ranged from 4940 to 520 TBq·yr -1 . Atmospheric release in rainy weather results in tritium migration into the ground water by a series of mechanisms associated with the water cycle. COGEMA monitors the ground water by means of bore holes. Atmospheric monitoring is also routinely performed; data on the tritium activity concentration in the air and rainwater are available for the same time period. A simplified observation suggests a relation between the atmospheric tritium release and the ground water radioactivity. In 1994, the activity ranged from 100 to 200 Bq·l -1 in the boreholes located 1 km and 2 km downwind from the point of release, diminishing with the distance to less than 20 Bq·l -1 at about 3 km. The authors attempted to model two types of transfers: atmospheric transfer from the release chimney to the borehole, and transfer in the alluvial ground water. The aquifer comprises the alluvial deposits forming the Codolet plain extending to the south of Marcoule, downwind from the point of atmospheric tritium release. The hydrogeology of the entire Marcoule site has been described in previous studies by the French bureau of geological and mineralogical research (BRGM) and ANTEA. (author)

INITIAL DATA RELEASE OF THE KEPLER-INT SURVEY

Energy Technology Data Exchange (ETDEWEB)

Greiss, S.; Steeghs, D.; Gaensicke, B. T. [Department of Physics, Astronomy and Astrophysics group, University of Warwick, CV4 7AL Coventry (United Kingdom); Martin, E. L. [INTA-CSIC Centro de Astrobiologia, Carretera de Ajalvir km 4, 28550 Torrejon de Ardoz (Spain); Groot, P. J.; Verbeek, K.; Jonker, P. G.; Scaringi, S. [Department of Astrophysics/IMAPP, Radboud University Nijmegen, P.O. Box 9010, 6500 GL Nijmegen (Netherlands); Irwin, M. J.; Gonzalez-Solares, E. [Cambridge Astronomy Survey Unit, Institute of Astronomy, University of Cambridge, Madingley Road, CB3 0HA Cambridge (United Kingdom); Greimel, R. [Institut fuer Physik, Karl-Franzen Universitaet Graz, Universitaetsplatz 5, 8010 Graz (Austria); Knigge, C. [School of Physics and Astronomy, University of Southampton, Southampton, Hampshire SO17 1BJ (United Kingdom); Ostensen, R. H. [Instituut voor Sterrenkunde, KU Leuven, Celestijnenlaan 200D, 3001 Leuven (Belgium); Drew, J. E.; Farnhill, H. [Centre for Astrophysics Research, University of Hertfordshire, College Lane, Hatfield AL10 9AB (United Kingdom); Drake, J.; Wright, N. J. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Ripepi, V. [INAF-Osservatorio Astronomico di Capodimonte, via Moiariello 16, Naples I-80131 (Italy); Southworth, J. [Astrophysics Group, Keele University, Newcastle-under-Lyme ST5 5BG (United Kingdom); Still, M., E-mail: s.greiss@warwick.ac.uk [NASA Ames Research Center, M/S 244-40, Moffett Field, CA 94035 (United States); and others

2012-07-15

This paper describes the first data release of the Kepler-INT Survey (KIS) that covers a 116 deg{sup 2} region of the Cygnus and Lyra constellations. The Kepler field is the target of the most intensive search for transiting planets to date. Despite the fact that the Kepler mission provides superior time-series photometry, with an enormous impact on all areas of stellar variability, its field lacks optical photometry complete to the confusion limit of the Kepler instrument necessary for selecting various classes of targets. For this reason, we follow the observing strategy and data reduction method used in the IPHAS and UVEX galactic plane surveys in order to produce a deep optical survey of the Kepler field. This initial release concerns data taken between 2011 May and August, using the Isaac Newton Telescope on the island of La Palma. Four broadband filters were used, U, g, r, i, as well as one narrowband one, H{alpha}, reaching down to a 10{sigma} limit of {approx}20th mag in the Vega system. Observations covering {approx}50 deg{sup 2}, thus about half of the field, passed our quality control thresholds and constitute this first data release. We derive a global photometric calibration by placing the KIS magnitudes as close as possible to the Kepler Input Catalog (KIC) photometry. The initial data release catalog containing around 6 million sources from all the good photometric fields is available for download from the KIS Web site (www.astro.warwick.ac.uk/research/kis/) as well as via MAST (KIS magnitudes can be retrieved using the MAST enhanced target search page http://archive.stsci.edu/kepler/kepler{sub f}ov/search.php and also via Casjobs at MAST Web site http://mastweb.stsci.edu/kplrcasjobs/).

INITIAL DATA RELEASE OF THE KEPLER-INT SURVEY

International Nuclear Information System (INIS)

Greiss, S.; Steeghs, D.; Gänsicke, B. T.; Martín, E. L.; Groot, P. J.; Verbeek, K.; Jonker, P. G.; Scaringi, S.; Irwin, M. J.; González-Solares, E.; Greimel, R.; Knigge, C.; Østensen, R. H.; Drew, J. E.; Farnhill, H.; Drake, J.; Wright, N. J.; Ripepi, V.; Southworth, J.; Still, M.

2012-01-01

This paper describes the first data release of the Kepler-INT Survey (KIS) that covers a 116 deg 2 region of the Cygnus and Lyra constellations. The Kepler field is the target of the most intensive search for transiting planets to date. Despite the fact that the Kepler mission provides superior time-series photometry, with an enormous impact on all areas of stellar variability, its field lacks optical photometry complete to the confusion limit of the Kepler instrument necessary for selecting various classes of targets. For this reason, we follow the observing strategy and data reduction method used in the IPHAS and UVEX galactic plane surveys in order to produce a deep optical survey of the Kepler field. This initial release concerns data taken between 2011 May and August, using the Isaac Newton Telescope on the island of La Palma. Four broadband filters were used, U, g, r, i, as well as one narrowband one, Hα, reaching down to a 10σ limit of ∼20th mag in the Vega system. Observations covering ∼50 deg 2 , thus about half of the field, passed our quality control thresholds and constitute this first data release. We derive a global photometric calibration by placing the KIS magnitudes as close as possible to the Kepler Input Catalog (KIC) photometry. The initial data release catalog containing around 6 million sources from all the good photometric fields is available for download from the KIS Web site (www.astro.warwick.ac.uk/research/kis/) as well as via MAST (KIS magnitudes can be retrieved using the MAST enhanced target search page http://archive.stsci.edu/kepler/kepler_fov/search.php and also via Casjobs at MAST Web site http://mastweb.stsci.edu/kplrcasjobs/).

Generating local scale land use/cover change scenarios: case studies of high-risk mountain areas

Science.gov (United States)

Malek, Žiga; Glade, Thomas; Boerboom, Luc

2014-05-01

The relationship between land use/cover changes and consequences to human well-being is well acknowledged and has led to higher interest of both researchers and decision makers in driving forces and consequences of such changes. For example, removal of natural vegetation cover or urban expansion resulting in new elements at risk can increase hydro-meteorological risk. This is why it is necessary to study how the land use/cover could evolve in the future. Emphasis should especially be given to areas experiencing, or expecting, high rates of socio-economic change. A suitable approach to address these changes is scenario development; it offers exploring possible futures and the corresponding environmental consequences, and aids decision-making, as it enables to analyse possible options. Scenarios provide a creative methodology to depict possible futures, resulting from existing decisions, based on different assumptions of future socio-economic development. They have been used in various disciplines and on various scales, such as flood risk and soil erosion. Several studies have simulated future scenarios of land use/cover changes at a very high success rate, however usually these approaches are tailor made for specific case study areas and fit to available data. This study presents a multi-step scenario generation framework, which can be transferable to other local scale case study areas, taking into account the case study specific consequences of land use/cover changes. Through the use of experts' and decision-makers' knowledge, we aimed to develop a framework with the following characteristics: (1) it enables development of scenarios that are plausible, (2) it can overcome data inaccessibility, (3) it can address intangible and external driving forces of land use/cover change, and (4) it ensures transferability to other local scale case study areas with different land use/cover change processes and consequences. To achieve this, a set of different methods is applied

Alternative cover design

International Nuclear Information System (INIS)

1988-11-01

The special study on Alternative Cover Designs is one of several studies initiated by the US Department of Energy (DOE) in response to the proposed US Environmental Protection Agency (EPA) groundwater standards. The objective of this study is to investigate the possibility of minimizing the infiltration of precipitation through stabilized tailings piles by altering the standard design of covers currently used on the Uranium Mill Tailings Remedial Action (UMTRA) Project. Prior. to the issuance of the proposed standards, UMTRA Project piles had common design elements to meet the required criteria, the most important of which were for radon diffusion, long-term stability, erosion protection, and groundwater protection. The standard pile covers consisted of three distinct layers. From top to bottom they were: rock for erosion protection; a sand bedding layer; and the radon barrier, usually consisting of a clayey sand material, which also functioned to limit infiltration into the tailings. The piles generally had topslopes from 2 to 4 percent and sideslopes of 20 percent

Land cover and water yield: inference problems when comparing catchments with mixed land cover

Directory of Open Access Journals (Sweden)

A. I. J. M. van Dijk

2012-09-01

Full Text Available Controlled experiments provide strong evidence that changing land cover (e.g. deforestation or afforestation can affect mean catchment streamflow (Q. By contrast, a similarly strong influence has not been found in studies that interpret Q from multiple catchments with mixed land cover. One possible reason is that there are methodological issues with the way in which the Budyko framework was used in the latter type studies. We examined this using Q data observed in 278 Australian catchments and by making inferences from synthetic Q data simulated by a hydrological process model (the Australian Water Resources Assessment system Landscape model. The previous contrasting findings could be reproduced. In the synthetic experiment, the land cover influence was still present but not accurately detected with the Budyko- framework. Likely sources of interpretation bias demonstrated include: (i noise in land cover, precipitation and Q data; (ii additional catchment climate characteristics more important than land cover; and (iii covariance between Q and catchment attributes. These methodological issues caution against the use of a Budyko framework to quantify a land cover influence in Q data from mixed land-cover catchments. Importantly, however, our findings do not rule out that there may also be physical processes that modify the influence of land cover in mixed land-cover catchments. Process model simulations suggested that lateral water redistribution between vegetation types and recirculation of intercepted rainfall may be important.

Land use/land cover study of urban features using spot imagery

International Nuclear Information System (INIS)

Mahmood, S.A.; Qureshi, J.; Abbas, I.

2005-01-01

This study is based on visual interpretation and classification of the urban area of Peshawar. Cloud free satellite image of the French SPOT System in panchromatic mode at 100m/pixel spatial detail was used for this purpose. The coverage area comprised nearly (7.5 x 6)sq. km. on the ground depicting the major portion of the city. Various image interpretation elements were exploited to accomplish the study, thirteen land cover classes were identified and demarcated on a tracing sheet. Having prepared the base map. Satellite image map was constructed by assigning disparate colors to the identified features. Dimensions of some of the prominent, regular and liner features were computed from the image. The results indicate that high-resolution satellite image can be effectively used for mapping and area estimation of urban land use/land cover features. (author)

Study of benzene release from Savannah River in-tank precipitation process slurry simulant

International Nuclear Information System (INIS)

Rappe, K.G.; Gauglitz, P.A.

1998-08-01

At the Savannah River Site, the in-tank precipitation (ITP) process uses sodium tetraphenylborate (NaTPB) to precipitate radioactive cesium from alkaline wastes. During this process, potassium is also precipitated to form 4-wt% KTPB/CsTPB slurry. Residual NaTPB decomposes to form benzene, which is retained by the waste slurry. The retained benzene is also readily released from the waste during subsequent waste processing. While the release of benzene certainly poses flammability and toxicological safety concerns, the magnitude of the hazard depends on the rate of release. Currently, the mechanisms controlling the benzene release rates are not well understood, and predictive models for estimating benzene release rates are not available. The overall purpose of this study is to obtain quantitative measurements of benzene release rates from a series of ITP slurry simulants. This information will become a basis for developing a quantitative mechanistic model of benzene release rates. The transient benzene release rate was measured from the surface of various ITP slurry (solution) samples mixed with benzene. The benzene release rate was determined by continuously purging the headspace of a sealed sample vessel with an inert gas (nitrogen) and analyzing that purged headspace vapor for benzene every minute

Determination of accident related release data

International Nuclear Information System (INIS)

Koch, W.; Nolte, O.; Lange, F.; Martens, R.

2004-01-01

For accident safety analyses, for the assessment of potential radiological consequences, for the review of current requirements of the Transport Regulations and for their possible further development as well as for the demonstration that radioactive materials such as LDM candidate material fulfil the regulatory requirements reliable release data following mechanical impact are required. This is definitely one of the demanding issues in the field of transport safety of radioactive materials. In this context special attention has to be paid to radioactive wastes immobilised in brittle materials, e.g. cement/concrete, glass, ceramics or other brittle materials such as fresh and spent fuel. In this presentation we report on a long-term experimental program aiming at improving the general physical understanding of the release process as well as the quantity and the quality of release data. By combining laboratory experiments using small scale test specimens with a few key scaling experiments with large scale test objects significant progress was achieved to meet this objective. The laboratory equipment enables the in-situ determination of the amount and aerodynamic size distribution of the airborne particles generated upon impact of the test specimen on a hard target. Impact energies cover the range experienced in transport accidents including aircraft accidents. The well defined experimental boundary conditions and the good reproducibility of the experimental procedure allowed for systematic studies to exactly measure the amount and aerodynamic size distribution of the airborne release and to quantify its dependence on relevant parameters such as energy input, material properties, and specimen geometry. The experimental program was performed within the scope of various national and international (e.g. EU-funded) projects. The small scale experiments with brittle materials revealed a pronounced universality of the airborne release in view of the material properties and

Controlled drug release on amine functionalized spherical MCM-41

Energy Technology Data Exchange (ETDEWEB)

Szegedi, Agnes, E-mail: szegedi@chemres.hu [Institute of Materials and Environmental Chemistry, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary); Popova, Margarita; Goshev, Ivan [Institute of Organic Chemistry with Centre of Phytochemistry, Bulgarian Academy of Sciences, Sofia (Bulgaria); Klebert, Szilvia [Institute of Materials and Environmental Chemistry, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary); Mihaly, Judit [Institute of Molecular Pharmacology, Research Centre for Natural Sciences, Hungarian Academy of Sciences, 1025 Budapest, Pusztaszeri ut 59-67 (Hungary)

2012-10-15

MCM-41 silica with spherical morphology and small particle sizes (100 nm) was synthesized and modified by post-synthesis method with different amounts of 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, was carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N{sub 2} physisorption, elemental analysis, thermal analysis and FT-IR spectroscopy. A new method was developed for the quantitative determination of amino groups in surface modified mesoporous materials by the ninhydrin reaction. Good correlation was found between the amino content of the MCM-41 materials determined by the ninhydrin method and their ibuprofen adsorption capacity. Amino modification resulted in high degree of ibuprofen loading and slow release rate in comparison to the parent non-modified MCM-41. - Graphical abstract: Determination of surface amino groups by ninhidrin method. Highlights: Black-Right-Pointing-Pointer Spherical MCM-41 modified by different amounts of APTES was studied. Black-Right-Pointing-Pointer Ibuprofen (IBU) adsorption and release characteristics was tested. Black-Right-Pointing-Pointer The ninhydrin reaction was used for the quantitative determination of amino groups. Black-Right-Pointing-Pointer Stoichiometric amount of APTES is enough for totally covering the surface with amino groups. Black-Right-Pointing-Pointer Good correlation was found between the amino content and IBU adsorption capacity.

pH-independent immediate release polymethacrylate formulations--an observational study.

Science.gov (United States)

Claeys, Bart; Vandeputte, Reinout; De Geest, Bruno G; Remon, Jean Paul; Vervaet, Chris

2016-01-01

Using Eudragit® E PO (EudrE) as a polymethacrylate carrier, the aim of the study was to develop a pH-independent dosage form containing ibuprofen (IBP) as an active compound via chemical modification of the polymer (i.e. quaternization of amine function) or via the addition of dicarboxylic acids (succinic, glutaric and adipic acid) to create a pH micro-environment during dissolution. Biconvex tablets (diameter: 10 mm; height: 5 mm) were produced via hot melt extrusion and injection molding. In vitro dissolution experiments revealed that a minimum of 25% of quaternization was sufficient to partially (up to pH 5) eliminate the pH-dependent effect of the EudrE/IBP formulation. The addition of dicarboxylic acids did not alter IBP release in a pH 1 and 3 medium as the dimethyl amino groups of EudrE are already fully protonated, while in a pH 5 solvent IBP release was significantly improved (cf. from 0% to 92% release after 1 h dissolution experiments upon the addition of 20 wt.% succinic acid). Hence, both approaches resulted in a pH-independent (up to pH 5) immediate release formulation. However, the presence of a positively charged polymer induced stability issues (recrystallization of API) and the formulations containing dicarboxylic acids were classified as mechanically unstable. Hence, further research is needed to obtain a pH-independent immediate release formulation while using EudrE as a polmethacrylate carrier.

Ion release from orthodontic brackets in 3 mouthwashes: an in-vitro study.

Science.gov (United States)

Danaei, Shahla Momeni; Safavi, Afsaneh; Roeinpeikar, S M Mehdi; Oshagh, Morteza; Iranpour, Shiva; Omidkhoda, Maryam; Omidekhoda, Maryam

2011-06-01

Stainless steel orthodontic brackets can release metal ions into the saliva. Fluoridated mouthwashes are often recommended to orthodontic patients to reduce the risk of white-spot lesions around their brackets. However, little information is available regarding the effect of different mouthwashes in ion release of orthodontic brackets. The purpose of this study was to measure the amount of metal ion release from orthodontic brackets when kept in different mouthwashes. One hundred sixty stainless steel brackets (0.022-in, 3M Unitek, Monrovia, Calif) were divided randomly into 4 equal groups and immersed in Oral B (Procter & Gamble, Weybridge, United Kingdom), chlorhexidine (Shahdaru Labratories, Tehran, Iran), and Persica (Poursina Pharmaceutical Laboratories, Tehran, Iran) mouthwashes and distilled deionized water and incubated at 37°C for 45 days. Nickel, chromium, iron, copper, and manganese released from the orthodontic brackets were measured with an inductively coupled plasma spectrometer. For statistical analysis, 1-way analysis of variance (ANOVA) and the Duncan multiple-range tests were used. The results showed that ion release in deionized water was significantly (P 0.05) in nickel, chromium, iron, and copper ion release in the Oral B and Persica mouthwashes. The level of manganese release was significantly different in all 4 groups. If ion release is a concern, Oral B and Persica mouthwashes might be better options than chlorhexidine for orthodontic patients with stainless steel brackets. Copyright © 2011 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

Drug release kinetic analysis and prediction of release data via polymer molecular weight in sustained release diltiazem matrices.

Science.gov (United States)

Adibkia, K; Ghanbarzadeh, S; Mohammadi, G; Khiavi, H Z; Sabzevari, A; Barzegar-Jalali, M

2014-03-01

This study was conducted to investigate the effects of HPMC (K4M and K100M) as well as tragacanth on the drug release rate of diltiazem (DLTZ) from matrix tablets prepared by direct compression method.Mechanism of drug transport through the matrices was studied by fitting the release data to the 10 kinetic models. 3 model independent parameters; i. e., mean dissolution time (MDT), mean release rate (MRR) and release rate efficacy (RE) as well as 5 time point approaches were established to compare the dissolution profiles. To find correlation between fraction of drug released and polymer's molecular weight, dissolution data were fitted into two proposed equations.All polymers could sustain drug release up to 10 h. The release data were fitted best to Peppas and Higuchi square root kinetic models considering squared correlation coefficient and mean percent error (MPE). RE and MRR were decreased when polymer to drug ratio was increased. Conversely, t60% was increased with raising polymer /drug ratio. The fractions of drug released from the formulations prepared with tragacanth were more than those formulated using the same amount of HPMC K4M and HPMC K100M.Preparation of DLTZ matrices applying HPMCK4M, HPMC K100M and tragacanth could effectively extend the drug release. © Georg Thieme Verlag KG Stuttgart · New York.

Large scientific releases

International Nuclear Information System (INIS)

Pongratz, M.B.

1981-01-01

The motivation for active experiments in space is considered, taking into account the use of active techniques to obtain a better understanding of the natural space environment, the utilization of the advantages of space as a laboratory to study fundamental plasma physics, and the employment of active techniques to determine the magnitude, degree, and consequences of artificial modification of the space environment. It is pointed out that mass-injection experiments in space plasmas began about twenty years ago with the Project Firefly releases. Attention is given to mass-release techniques and diagnostics, operational aspects of mass release active experiments, the active observation of mass release experiments, active perturbation mass release experiments, simulating an artificial modification of the space environment, and active experiments to study fundamental plasma physics

Land cover mapping of North and Central America—Global Land Cover 2000

Science.gov (United States)

Latifovic, Rasim; Zhu, Zhi-Liang

2004-01-01

The Land Cover Map of North and Central America for the year 2000 (GLC 2000-NCA), prepared by NRCan/CCRS and USGS/EROS Data Centre (EDC) as a regional component of the Global Land Cover 2000 project, is the subject of this paper. A new mapping approach for transforming satellite observations acquired by the SPOT4/VGTETATION (VGT) sensor into land cover information is outlined. The procedure includes: (1) conversion of daily data into 10-day composite; (2) post-seasonal correction and refinement of apparent surface reflectance in 10-day composite images; and (3) extraction of land cover information from the composite images. The pre-processing and mosaicking techniques developed and used in this study proved to be very effective in removing cloud contamination, BRDF effects, and noise in Short Wave Infra-Red (SWIR). The GLC 2000-NCA land cover map is provided as a regional product with 28 land cover classes based on modified Federal Geographic Data Committee/Vegetation Classification Standard (FGDC NVCS) classification system, and as part of a global product with 22 land cover classes based on Land Cover Classification System (LCCS) of the Food and Agriculture Organisation. The map was compared on both areal and per-pixel bases over North and Central America to the International Geosphere–Biosphere Programme (IGBP) global land cover classification, the University of Maryland global land cover classification (UMd) and the Moderate Resolution Imaging Spectroradiometer (MODIS) Global land cover classification produced by Boston University (BU). There was good agreement (79%) on the spatial distribution and areal extent of forest between GLC 2000-NCA and the other maps, however, GLC 2000-NCA provides additional information on the spatial distribution of forest types. The GLC 2000-NCA map was produced at the continental level incorporating specific needs of the region.

Effective release of lignin fragments from Lignocellulose by Lewis Acid Metal triflates in the lignin-first approach

NARCIS (Netherlands)

Huang, X.; Zhu, J.; Koranyi, T.I.; Boot, M.D.; Hensen, E.J.M.

2016-01-01

Cover image: Invited for this month′s cover is the group of Emiel Hensen at the Eindhoven University of Technology. The image shows how the lignin component can be effectively released from wood and converted into aromatics over a tandem Al-triflate and Pd/C catalyst.

Experimental studies on helium release and stratification within the AIHMS facility

International Nuclear Information System (INIS)

Prabhakar, Aneesh; Agrawal, Nilesh; Raghavan, V.; Das, Sarit K.

2015-01-01

Hydrogen is generated during core meltdown accidents in nuclear power plants. The study of hydrogen release and mixing within the containment is an important area of safety research. An experimental setup called the AERB-IIT Madras Hydrogen Mixing Studies (AIHMS) facility is setup at IIT Madras to study the distribution of helium (an inert surrogate to hydrogen) subsequent to release as a jet. The present paper gives details of the design, fabrication and instrumentation of the AIHMS facility. It then compares the features of the facility with respect to other facilities existing for hydrogen mitigation studies. Then it gives details of the experiments on concentration build-up studies as a result of injection of gases (air and helium) performed in this experimental facility. (author)

Post-release habitats’ selection of Capreolus capreolus italicus (Festa, 1925 in a protected area in southern Italy

Directory of Open Access Journals (Sweden)

Giovanni Argenti

2015-01-01

Full Text Available The purpose of this study was to analyze the post-release behavior of individuals of Capreolus capreolus italicus (Festa 1925 and to evaluate the influence of environmental and vegetation characteristics on habitat selection by monitored animals. With these aims, 14 individuals of roe deer (a sample of 75 animals released in total, differentiated by age and sex, were caught in areas of southern Tuscany (central Italy and released in suitable areas of the Aspromonte National Park (Calabria, southern Italy. Each animal was monitored by GPS-GSM tracking radio collar (Vectronics ® with frequency of location ranging from 30 minutes (in the first month to 6 hours (later, and covering a period ranging from 90 to 563 days. Each fix, reported in a GIS environment, was analyzed to get information on habitat selection performed by tracked animals. Data collection implemented forest area, herbaceous resources characterization and the evaluation of possible visual refuge offered to the animals by the environment, to assess the effect of these attributes on the selection of grounds. Results showed that the choice of a particular habitat is highly correlated with forests’ characteristics, the areas covered by conifers and with height of crown insertion between 1 and 2 m, generally with absence of regeneration, being clearly preferred. Most attended herbaceous areas are those with a high presence of grasses and with a high pastoral value. Visual refuge affects also remarkably the selection of habitats by animals. The study showed that the observed parameters can provide a good basis for the validation of the model used for the feasibility study and to identify the optimal characteristics of the areas for future releases.

Study on mitigation of in-vessel release of fission products in severe accidents of PWR

International Nuclear Information System (INIS)

Huang, G.F.; Tong, L.L.; Li, J.X.; Cao, X.W.

2010-01-01

Research highlights: → In-vessel release of fission products in severe accidents for 600 MW PWR is analyzed. → Mitigation effect of primary feed-and-bleed on in-vessel release is investigated. → Mitigation effect of secondary feed-and-bleed on in-vessel release is studied. → Mitigation effect of ex-vessel cooling on in-vessel release is evaluated. - Abstract: During the severe accidents in a nuclear power plant, large amounts of fission products release with accident progression, including in-vessel and ex-vessel release. Mitigation of fission products release is demanded for alleviating radiological consequence in severe accidents. Mitigation countermeasures to in-vessel release are studied for Chinese 600 MW pressurized water reactor (PWR), including feed-and-bleed in primary circuit, feed-and-bleed in secondary circuit and ex-vessel cooling. SBO, LOFW, SBLOCA and LBLOCA are selected as typical severe accident sequences. Based on the evaluation of in-vessel release with different startup time of countermeasure, and the coupling relationship between thermohydraulics and in-vessel release of fission products, some results are achieved. Feed-and-bleed in primary circuit is an effective countermeasure to mitigate in-vessel release of fission products, and earlier startup time of countermeasure is more feasible. Feed-and-bleed in secondary circuit is also an effective countermeasure to mitigate in-vessel release for most severe accident sequences that can cease core melt progression, e.g. SBO, LOFW and SBLOCA. Ex-vessel cooling has no mitigation effect on in-vessel release owing to inevitable core melt and relocation.

Mark-release-recapture studies with Aedes dorsalis (Diptera: Culicidae) in coastal northern California.

Science.gov (United States)

Kramer, V L; Carper, E R; Beesley, C; Reisen, W K

1995-05-01

Two mark-release-recapture studies were conducted along the Sacramento-San Joaquin River Delta in northern California to describe the population ecology and dispersal pattern of Aedes dorsalis (Meigen). Immature Ae. dorsalis were collected from saline tidal marshes, reared to adults, marked, and released. Recapture grids during the July and September studies were within 8.0 and 2.4 km of the release sites, and recapture rates were 0.1 and 1.2%, respectively. The longest recorded flight was 5.8 km, and mosquitoes were recaptured up to 15 d after release. In September, 84% of the marked mosquitoes were recaptured within 2.0 km of the release site, and the mean dispersal distance was 1.9 km. Marked mosquitoes flew predominantly downwind to the east. There was no evidence that Ae. dorsalis traversed the 1.6-km-wide river from Contra Costa to Solano County. Temporal and spatial recapture patterns indicated a possible short-range migration pattern from oviposition sites to upland host-seeking areas. Changes in the recapture rate with cohort age delineated a 7-d gonotrophic cycle during September.

A comprehensive change detection method for updating the National Land Cover Database to circa 2011

Science.gov (United States)

Jin, Suming; Yang, Limin; Danielson, Patrick; Homer, Collin G.; Fry, Joyce; Xian, George

2013-01-01

The importance of characterizing, quantifying, and monitoring land cover, land use, and their changes has been widely recognized by global and environmental change studies. Since the early 1990s, three U.S. National Land Cover Database (NLCD) products (circa 1992, 2001, and 2006) have been released as free downloads for users. The NLCD 2006 also provides land cover change products between 2001 and 2006. To continue providing updated national land cover and change datasets, a new initiative in developing NLCD 2011 is currently underway. We present a new Comprehensive Change Detection Method (CCDM) designed as a key component for the development of NLCD 2011 and the research results from two exemplar studies. The CCDM integrates spectral-based change detection algorithms including a Multi-Index Integrated Change Analysis (MIICA) model and a novel change model called Zone, which extracts change information from two Landsat image pairs. The MIICA model is the core module of the change detection strategy and uses four spectral indices (CV, RCVMAX, dNBR, and dNDVI) to obtain the changes that occurred between two image dates. The CCDM also includes a knowledge-based system, which uses critical information on historical and current land cover conditions and trends and the likelihood of land cover change, to combine the changes from MIICA and Zone. For NLCD 2011, the improved and enhanced change products obtained from the CCDM provide critical information on location, magnitude, and direction of potential change areas and serve as a basis for further characterizing land cover changes for the nation. An accuracy assessment from the two study areas show 100% agreement between CCDM mapped no-change class with reference dataset, and 18% and 82% disagreement for the change class for WRS path/row p22r39 and p33r33, respectively. The strength of the CCDM is that the method is simple, easy to operate, widely applicable, and capable of capturing a variety of natural and

Release of information: are hospitals taking a hit?

Science.gov (United States)

Bellenghi, G Michael; Coffey, Bonnie; Fournier, Joseph E; McDavid, Jan P

2008-11-01

Outsourcing release-of-information requests helps hospitals alleviate administrative and compliance burdens and expense. Recently, state lawmakers have begun to draft legislation reducing the maximum fee that may be charged for copies of electronically stored records. The reduced fees may not cover expenses. If such legislation makes it difficult for outsourcing companies to make a profit from this service, hospitals ultimately could bear the expense and risk.

Mechanistic Studies on the Triggered Release of Liposomal Contents by Matrix Metalloproteinase-9

Science.gov (United States)

Elegbede, Adekunle I.; Banerjee, Jayati; Hanson, Andrea J.; Tobwala, Shakila; Ganguli, Bratati; Wang, Rongying; Lu, Xiaoning; Srivastava, D. K.; Mallik, Sanku

2009-01-01

Matrix metalloproteinases (MMPs) are a class of extracellular matrix degrading enzymes over-expressed in many cancers and contribute to the metastatic ability of the cancer cells. We have recently demonstrated that liposomal contents can be released when triggered by the enzyme MMP-9. Herein, we report our results on the mechanistic studies of the MMP-9 triggered release of the liposomal contents. We synthesized peptides containing the cleavage site for MMP-9 and conjugated them with fatty acids to prepare the corresponding lipopeptides. By employing Circular Dichroism spectroscopy, we demonstrate that the lipopeptides, when incorporated in liposomes, are de-mixed in the lipid bilayers and generate triple helical structures. MMP-9 cleaves the triple helical peptides, leading to the release of the liposomal contents. Other MMPs, which cannot hydrolyze triple helical peptides, failed to release the contents from the liposomes. We also observed that the rate and the extent of release of the liposomal contents depend on the mismatch between acyl chains of the synthesized lipopeptide and phospholipid components of the liposomes. Circular Dichroism spectroscopic studies imply that the observed differences in the release reflect the ability of the liposomal membrane to anneal the defects following the enzymatic cleavage of the liposome-incorporated lipopeptides. PMID:18642903

DESIGN, PERFORMANCE, AND SUSTAINABILITY OF ENGINEERED COVERS FOR URANIUM MILL TAILINGS

Energy Technology Data Exchange (ETDEWEB)

Waugh, W. Jody

2004-04-21

Final remedies at most uranium mill tailings sites include engineered covers designed to contain metals and radionuclides in the subsurface for hundreds of years. Early cover designs rely on compacted soil layers to limit water infiltration and release of radon, but some of these covers inadvertently created habitats for deep-rooted plants. Root intrusion and soil development increased the saturated hydraulic conductivity several orders of magnitude above design targets. These covers may require high levels of maintenance to sustain long-term performance. Relatively low precipitation, high potential evapotranspiration, and thick unsaturated soils favor long-term hydrologic isolation of buried waste at arid and semiarid sites. Later covers were designed to mimic this natural soil-water balance with the goal of sustaining performance with little or no maintenance. For example, the cover for the Monticello, Utah, Superfund site relies on a thick soil-sponge layer overlying a sand-and-gravel capillary barrier to store precipitation while plants are dormant and on native vegetation to dry the soil sponge during the growing season. Measurements of both off-site caisson lysimeters and a large 3-ha lysimeter built into the final cover show that drainage has been well below a U.S. Environmental Protection Agency target of less than 3.0 mm/yr. Our stewardship strategy combines monitoring precursors to failure, probabilistic riskbased modeling, and characterization of natural analogs to project performance of covers for a range of possible future environmental scenarios. Natural analogs are needed to understand how ecological processes will influence cover performance, processes that cannot be predicted with short-term monitoring and existing numerical models.

Land-cover change detection

Science.gov (United States)

Chen, Xuexia; Giri, Chandra; Vogelmann, James

2012-01-01

Land cover is the biophysical material on the surface of the earth. Land-cover types include grass, shrubs, trees, barren, water, and man-made features. Land cover changes continuously.  The rate of change can be either dramatic and abrupt, such as the changes caused by logging, hurricanes and fire, or subtle and gradual, such as regeneration of forests and damage caused by insects (Verbesselt et al., 2001).  Previous studies have shown that land cover has changed dramatically during the past sevearal centuries and that these changes have severely affected our ecosystems (Foody, 2010; Lambin et al., 2001). Lambin and Strahlers (1994b) summarized five types of cause for land-cover changes: (1) long-term natural changes in climate conditions, (2) geomorphological and ecological processes, (3) human-induced alterations of vegetation cover and landscapes, (4) interannual climate variability, and (5) human-induced greenhouse effect.  Tools and techniques are needed to detect, describe, and predict these changes to facilitate sustainable management of natural resources.

A Three-Pulse Release Tablet for Amoxicillin: Preparation, Pharmacokinetic Study and Physiologically Based Pharmacokinetic Modeling.

Science.gov (United States)

Li, Jin; Chai, Hongyu; Li, Yang; Chai, Xuyu; Zhao, Yan; Zhao, Yunfan; Tao, Tao; Xiang, Xiaoqiang

2016-01-01

Amoxicillin is a commonly used antibiotic which has a short half-life in human. The frequent administration of amoxicillin is often required to keep the plasma drug level in an effective range. The short dosing interval of amoxicillin could also cause some side effects and drug resistance, and impair its therapeutic efficacy and patients' compliance. Therefore, a three-pulse release tablet of amoxicillin is desired to generate sustained release in vivo, and thus to avoid the above mentioned disadvantages. The pulsatile release tablet consists of three pulsatile components: one immediate-release granule and two delayed release pellets, all containing amoxicillin. The preparation of a pulsatile release tablet of amoxicillin mainly includes wet granulation craft, extrusion/spheronization craft, pellet coating craft, mixing craft, tablet compression craft and film coating craft. Box-Behnken design, Scanning Electron Microscope and in vitro drug release test were used to help the optimization of formulations. A crossover pharmacokinetic study was performed to compare the pharmacokinetic profile of our in-house pulsatile tablet with that of commercial immediate release tablet. The pharmacokinetic profile of this pulse formulation was simulated by physiologically based pharmacokinetic (PBPK) model with the help of Simcyp®. Single factor experiments identify four important factors of the formulation, namely, coating weight of Eudragit L30 D-55 (X1), coating weight of AQOAT AS-HF (X2), the extrusion screen aperture (X3) and compression forces (X4). The interrelations of the four factors were uncovered by a Box-Behnken design to help to determine the optimal formulation. The immediate-release granule, two delayed release pellets, together with other excipients, namely, Avicel PH 102, colloidal silicon dioxide, polyplasdone and magnesium stearate were mixed, and compressed into tablets, which was subsequently coated with Opadry® film to produce pulsatile tablet of

Sustainable covers for uranium mill tailings, USA: alternative design, performance, and renovation - 16369

International Nuclear Information System (INIS)

Waugh, William J.; Benson, Craig H.; Albright, William H.

2009-01-01

The U.S. Department of Energy Office of Legacy Management is investigating alternatives to conventional cover designs for uranium mill tailings. A cover constructed in 2000 near Monticello, Utah, USA, was a redundant design with a conventional low-conductivity composite cover overlain with an alternative cover designed to mimic the natural soil water balance as measured in nearby undisturbed native soils and vegetation. To limit percolation, the alternative cover design relies on a 160-cm layer of sandy clay loam soil overlying a 40- cm sand capillary barrier for water storage, and a planting of native sagebrush steppe vegetation to seasonally release soil water through evapotranspiration (ET). Water balance monitoring within a 3.0-ha drainage lysimeter, embedded in the cover during construction, provided convincing evidence that the cover has performed well over a 9-year period (2000- 2009). The total cumulative percolation, 4.8 mm (approximately 0.5 mm yr -1 ), satisfied a regulatory goal of -1 . Most percolation can be attributed to the very wet winter and spring of 2004-2005, when soil water content exceeded the storage capacity of the cover. Diversity, percent cover, and leaf area of vegetation increased over the monitoring period. Field and laboratory evaluations several years after construction show that soil structural development, changes in soil hydraulic properties, and development of vegetation patterns have not adversely impacted cover performance. A new test facility was constructed in 2008 near Grand Junction, Colorado, USA, to evaluate low-cost methods for renovating or transforming conventional covers into more sustainable ET covers. (authors)

IFPE/IFA-432, Fission Gas Release, Mechanical Interaction BWR Fuel Rods, Halden

International Nuclear Information System (INIS)

Turnbull, J.A.

1996-01-01

Description: It contains data from experiments that have been performed at the IFE/OECD Halden Reactor Project, available for use in fuel performance studies. It covers experiments on thermal performance, fission product release, clad properties and pellet clad mechanical interaction. It includes also experimental data relevant to high burn-up behaviour. IFA-432: Measurements of fuel temperature response, fission gas release and mechanical interaction on BWR-type fuel rods up to high burn-ups. The assembly featured several variations in rod design parameters, including fuel type, fuel/cladding gap size, fill gas composition (He and Xe) and fuel stability. It contained 6 BWR-type fuel rods with fuel centre thermocouples at two horizontal planes, rods were also equipped with pressure transducers and cladding extensometers. Only data from 6 rods are compiled here

Releases of radioactivity from uranium mills and effluent treatment costs

International Nuclear Information System (INIS)

Witherspoon, J.P.; Sears, M.B.; Blanco, R.E.

1977-01-01

Airborne releases of radioactive materials from uranium milling to the environment consist of ore dust, yellowcake dust, tailings dust, and radon gas while the mill is active. After a mill has ceased operations, tailings may be stabilized to minimize or prevent airborne releases of radioactive particulates. However, radon gas will continue to be released in amounts inversely proportional to the degree of stabilization treatment (and expense). Liquid waste disposal is by evaporation and natural seepage to the ground beneath the tailings impoundment area. The release of radioactive materials (and potential radiation exposures) determines the majority of costs associated with minimizing the environmental impact of uranium milling. Radwaste treatments to reduce estimated radiation doses to individuals to 3 to 5% of those received with current milling practices are equivalent to $0.66 per pounds of U 3 O 8 and 0.032 mill per kWhr of electricity. This cost would cover a high efficiency reverse jet bag filter and high energy venturi scrubbers for dusts, neutralization of liquids, and an asphalt-lined tailings basin with a clay core dam to reduce seepage. In addition, this increased cost would cover stabilization of tailings, after mill closure, with a 1-in. asphalt membrane topped by 2 ft of earth and 0.5 ft of crushed rock to provide protection against future leaching and wind erosion. The cost of reducing the radiological hazards associated with uranium milling to this degree would contribute about 0.4% to the current total cost of nuclear power

Preparation and release study of Triclosan in polyethylene/Triclosan anti-bacterial blend.

Science.gov (United States)

Kamalipour, Jamshid; Masoomi, Mahmood; Khonakdar, Hossein Ali; Razavi, Seyed Mohammad Reza

2016-09-01

In this study, medium density polyethylene (MDPE) incorporated with Triclosan antibacterial substance has been prepared and Triclosan release rate was investigated. The crystallinity level and matrix polarity, as two significant parameters in antibacterial release control, were studied. Triclosan, a well-established widespread antibacterial agent, was incorporated into medium density polyethylene (MDPE) and Maleic anhydride grafted polyethylene (PE-g-MA) was used to change the polarity of the MDPE matrix. A masterbatch of 10wt% Triclosan incorporated with the MDPE and various PE-g-MA concentrations were prepared using an internal mixer. Then the masterbatch was diluted in the MDPE matrix to produce compounds with 0.1, 0.5, and1wt% Triclosan via twin screw extruder. The compounds were molded by compression molding method and then were cooled in three different cooling rate methods: isothermal cooling (I), quenching (Q),and moderate 5-10°C/min cooling rate (M). Cooling rate effects on crystallinity level were investigated applying sample density measurement. UV-vis absorption spectroscopy was used to probe the release of Triclosan. Antibacterial properties of the compounds against Escherichia coli, Klebsiella pneumoniae, and Staphylococcus aureus were measured. The results showed that by addition of PE-g-MA, Triclosan release rate was increased. It was confirmed that the sample crystallinity was decreased by the cooling rate enhancement. The results also showed that quenched samples indicated higher release of Triclosan. Cooling rate reduction and raising the polarity increased the release of Triclosan and improved the antibacterial properties of the compounds. Copyright © 2016 Elsevier B.V. All rights reserved.

Smoking-induced dopamine release studied with [11C]raclopride PET

International Nuclear Information System (INIS)

Kim, Yu Kyeong; Cho, Sang Soo; Lee, Do Hoon

2005-01-01

It has been postulated that dopamine release in the striatum underlies the reinforcing properties of nicotine. Substantial evidence in the animal studies demonstrates that nicotine interacts with and regulates the activation of the dopaminergic neuron. The aim of this study was to visualize the dopamine release by smoking in human brain using PET scan with [ 11 C]raclopride. Four male non-smokers or ex-smokers with an abstinence period longer than 1 year (mean age of 24.3±2.6 years) were enrolled in this study. Dopamine D2 receptor radioligand, [ 11 C]raclopride was administrated with bolus-plus-constant infusion. Dynamic PET was performed during 120 minutes (3x20s, 2x60s, 2x120s, 1x180s and 22x300s). Following the 50 minute-scanning, subjects smoked a cigarette containing 1 mg of nicotine while in the scanner. Blood samples for the measurements of plasma nicotine levels were collected at 0, 5, 10, 15, 20, 25, 30, 45, 60, and 90 minute after smoking. Regions for striatal structures were drawn on the coronal summed PET images guided with co-registered MRI. Binding potential, calculated as striatal-cerebellar/cerebellar activity, was measured under equilibrium condition at baseline and smoking session. The mean change in binding potential between the baseline and smoking in caudate, Putamen and ventral striatum was 3.7 % , 4.0 % and 8.6 %, respectively. This indicated the striatal dopamine release by smoking. The reduction in binding potential in the ventral striatum was significantly correlated with the cumulated plasma level of the nicotine (r 2 =0.91, p=0.04). These data demonstrate that in vivo imaging with [ 11 C]raclopride PET could measure nicotine-induced dopamine release in the human brain, which has a significant positive correlation with the amount of nicotine administered by smoking

Sustained-release progesterone vaginal suppositories 1--development of sustained-release granule--.

Science.gov (United States)

Nakayama, Ayako; Sunada, Hisakazu; Okamoto, Hirokazu; Furuhashi, Kaoru; Ohno, Yukiko; Ito, Mikio

2009-02-01

Progesterone (P) is an important hormone for the establishment of pregnancy, and its administration is useful for luteal insufficiency. Considering the problems of commercially available oral and injection drugs, hospital-formulated vaginal suppositories are clinically used. However, since the half-life of P suppositories is short, it is difficult to maintain its constant blood concentration. To sustain drug efficacy and prevent side-effects, we are attempting to develop sustained-release suppositories by examining the degree of sustained-release of active ingredients. In this study, we examined the combinations of granulation methods and release systems for the preparation of sustained-release granules of P, and produced 13 types of sustained-release granules. We also examined the diameter, content, and dissolution of each type of granules, and confirmed that the sustained-release of all types of granules was satisfactory. Among the sustained-release granules, we selected granules with a content and a degree of sustained-release suitable for sustained-release suppositories.

Climate Impacts of Cover Crops

Science.gov (United States)

Lombardozzi, D.; Wieder, W. R.; Bonan, G. B.; Morris, C. K.; Grandy, S.

2016-12-01

Cover crops are planted in agricultural rotation with the intention of protecting soil rather than harvest. Cover crops have numerous environmental benefits that include preventing soil erosion, increasing soil fertility, and providing weed and pest control- among others. In addition to localized environmental benefits, cover crops can have important regional or global biogeochemical impacts by increasing soil organic carbon, changing emissions of greenhouse trace gases like nitrous oxide and methane, and reducing hydrologic nitrogen losses. Cover crops may additionally affect climate by changing biogeophysical processes, like albedo and latent heat flux, though these potential changes have not yet been evaluated. Here we use the coupled Community Atmosphere Model (CAM5) - Community Land Model (CLM4.5) to test how planting cover crops in the United States may change biogeophysical fluxes and climate. We present seasonal changes in albedo, heat fluxes, evaporative partitioning, radiation, and the resulting changes in temperature. Preliminary analyses show that during seasons when cover crops are planted, latent heat flux increases and albedo decreases, changing the evaporative fraction and surface temperatures. Understanding both the biogeophysical changes caused by planting cover crops in this study and the biogeochemical changes found in other studies will give a clearer picture of the overall impacts of cover crops on climate and atmospheric chemistry, informing how this land use strategy will impact climate in the future.

Land cover change impact on urban flood modeling (case study: Upper Citarum watershed)

Science.gov (United States)

Siregar, R. I.

2018-03-01

The upper Citarum River watershed utilizes remote sensing technology in Geographic Information System to provide information on land coverage by interpretation of objects in the image. Rivers that pass through urban areas will cause flooding problems causing disadvantages, and it disrupts community activities in the urban area. Increased development in a city is related to an increase in the number of population growth that added by increasing quality and quantity of life necessities. Improved urban lifestyle changes have an impact on land cover. The impact in over time will be difficult to control. This study aims to analyze the condition of flooding in urban areas caused by upper Citarum watershed land-use change in 2001 with the land cover change in 2010. This modeling analyzes with the help of HEC-RAS to describe flooded inundation urban areas. Land cover change in upper Citarum watershed is not very significant; it based on the results of data processing of land cover has the difference of area that changed is not enormous. Land cover changes for the floods increased dramatically to a flow coefficient for 2001 is 0.65 and in 2010 at 0.69. In 2001, the inundation area about 105,468 hectares and it were about 92,289 hectares in 2010.

[Studies on preparation and dissolution test in vitro of sustained-release dropping pills of curcumin].

Science.gov (United States)

Fang, Yu; Xiang, Bai; Pan, Zhen-Hua; Cao, De-Ying

2010-01-01

To study the prescription and technique of sustained-release dropping pills of curcumin and inspect their release property in vitro. The orthogonal test was used to screen the prescription and technique which were definited with the colligation evaluation of release and formation of dropping pills. The optimization of prescription and technique were as follows: stearic acid 70 mg, glycery monostearate 25 mg, solutol 6 mg, viscosity of cooling liquid was 100 mm2/s; the temperature of material liquid was 80 degrees C; the cooling temperature was 30 - 0 degrees C; the dropping speed was (21 +/- 2) dripping/min. The release behavior of sustained-release dropping pills of curcumin coincidented with Higuchi equation well and the character of sustained-release was transparent. The sustained-release dropping pills of curcumin have good property of sustained-release in vitro and their release behavior in vivo need to be inspected.

Fabrication of drug eluting implants: study of drug release mechanism from titanium dioxide nanotubes

International Nuclear Information System (INIS)

Hamlekhan, Azhang; Shokuhfar, Tolou; Sinha-Ray, Suman; Yarin, Alexander L; Takoudis, Christos; Mathew, Mathew T; Sukotjo, Cortino

2015-01-01

Formation of titanium dioxide nanotubes (TNTs) on a titanium surface holds great potential for promoting desirable cellular response. However, prolongation of drug release from these nano-reservoirs remains to be a challenge. In our previous work TNTs were successfully loaded with a drug. In this study the effect of TNTs dimensions on prolongation of drug release is quantified aiming at the introduction of a simple novel technique which overcomes complications of previously introduced methods. Different groups of TNTs with different lengths and diameters are fabricated. Samples are loaded with a model drug and rate of drug release over time is monitored. The relation of the drug release rate to the TNT dimensions (diameter, length, aspect ratio and volume) is established. The results show that an increase in any of these parameters increases the duration of the release process. However, the strongest parameter affecting the drug release is the aspect ratio. In fact, TNTs with higher aspect ratios release drug slower. It is revealed that drug release from TNT is a diffusion-limited process. Assuming that diffusion of drug in (Phosphate-Buffered Saline) PBS follows one-dimensional Fick’s law, the theoretical predictions for drug release profile is compatible with our experimental data for release from a single TNT. (paper)

Automated identification of potential snow avalanche release areas based on digital elevation models

Directory of Open Access Journals (Sweden)

Y. Bühler

2013-05-01

Full Text Available The identification of snow avalanche release areas is a very difficult task. The release mechanism of snow avalanches depends on many different terrain, meteorological, snowpack and triggering parameters and their interactions, which are very difficult to assess. In many alpine regions such as the Indian Himalaya, nearly no information on avalanche release areas exists mainly due to the very rough and poorly accessible terrain, the vast size of the region and the lack of avalanche records. However avalanche release information is urgently required for numerical simulation of avalanche events to plan mitigation measures, for hazard mapping and to secure important roads. The Rohtang tunnel access road near Manali, Himachal Pradesh, India, is such an example. By far the most reliable way to identify avalanche release areas is using historic avalanche records and field investigations accomplished by avalanche experts in the formation zones. But both methods are not feasible for this area due to the rough terrain, its vast extent and lack of time. Therefore, we develop an operational, easy-to-use automated potential release area (PRA detection tool in Python/ArcGIS which uses high spatial resolution digital elevation models (DEMs and forest cover information derived from airborne remote sensing instruments as input. Such instruments can acquire spatially continuous data even over inaccessible terrain and cover large areas. We validate our tool using a database of historic avalanches acquired over 56 yr in the neighborhood of Davos, Switzerland, and apply this method for the avalanche tracks along the Rohtang tunnel access road. This tool, used by avalanche experts, delivers valuable input to identify focus areas for more-detailed investigations on avalanche release areas in remote regions such as the Indian Himalaya and is a precondition for large-scale avalanche hazard mapping.

Automated identification of potential snow avalanche release areas based on digital elevation models

Science.gov (United States)

Bühler, Y.; Kumar, S.; Veitinger, J.; Christen, M.; Stoffel, A.; Snehmani

2013-05-01

The identification of snow avalanche release areas is a very difficult task. The release mechanism of snow avalanches depends on many different terrain, meteorological, snowpack and triggering parameters and their interactions, which are very difficult to assess. In many alpine regions such as the Indian Himalaya, nearly no information on avalanche release areas exists mainly due to the very rough and poorly accessible terrain, the vast size of the region and the lack of avalanche records. However avalanche release information is urgently required for numerical simulation of avalanche events to plan mitigation measures, for hazard mapping and to secure important roads. The Rohtang tunnel access road near Manali, Himachal Pradesh, India, is such an example. By far the most reliable way to identify avalanche release areas is using historic avalanche records and field investigations accomplished by avalanche experts in the formation zones. But both methods are not feasible for this area due to the rough terrain, its vast extent and lack of time. Therefore, we develop an operational, easy-to-use automated potential release area (PRA) detection tool in Python/ArcGIS which uses high spatial resolution digital elevation models (DEMs) and forest cover information derived from airborne remote sensing instruments as input. Such instruments can acquire spatially continuous data even over inaccessible terrain and cover large areas. We validate our tool using a database of historic avalanches acquired over 56 yr in the neighborhood of Davos, Switzerland, and apply this method for the avalanche tracks along the Rohtang tunnel access road. This tool, used by avalanche experts, delivers valuable input to identify focus areas for more-detailed investigations on avalanche release areas in remote regions such as the Indian Himalaya and is a precondition for large-scale avalanche hazard mapping.

In-vitro Release Study of Carvedilol Phosphate Matrix Tablets ...

African Journals Online (AJOL)

Microcrystalline cellulose (Avicel PH 101), starch (Sta-Rx 1500) and lactose monohydrate were used as diluents in the formulations while the effect of sodium lauryl sulphate (wetting agent) was studied for some of the formulations. The tablets were characterized for carvedilol phosphate release in both simulated gastric and ...

Development of paradigm for the study of amino acid neurotransmitter release in human autopsy brain samples

International Nuclear Information System (INIS)

Kuo, K.-W.; Dodd, P.R.

2001-01-01

Full text: This study attempted to establish a release protocol to characterize both the vesicular and cytoplasmic components of amino acid transmitter release in human synaptosomes. Experiments with rat synaptosomes showed that, with depolarizing concentrations of K + ions, vesicular release could be successfully differentiated from cytoplasmic release for preloaded L-[ 3 H ]glutamate and [ 14 C ]GABA. However, human tissue studies did not give clear-cut results. Experiments were carried out to optimize the release paradigm as well as to improve the vesicular uptake of labeled transmitters. A 'pulse- chase' protocol, with an unlabelled D-aspartate chase, was performed in human tissue samples in order to enhance the L-[ 3 H ] glutamate release signal derived from exocytosis by removing the cytoplasmic pool of L-[ 3 H ] glutamate first. However, the results showed that total release was not enhanced effectively in comparison with the non-pulse-chase protocol. In brief, the pulse-chase protocol did not build up the vesicular pool of L-[ 3 H ]glutamate, though the cytoplasmic L- [ 3 H ] glutamate pool was effectively depressed by D-aspartate. Further studies applied 4- aminopyridine (4-AP) to trigger release, to circumvent the problem of the reversal of plasma membrane transporters caused by raised K + ion concentrations. The results showed that the application of 4-AP elicited the release of amino acid transmitters from rat synaptosomes, but failed to produce successful release signals in the human tissue experiments. Our findings suggest that the vesicular compartment may be impaired by freezing and affected by post-mortem delay (PMD). Rat studies showed that the freezing step had a major effect on Ca 2+-dependent release, as less L- [3 H ]glutamate and [ 14 C ]GABA were released from the frozen rat tissue preparations. Moreover, there was an indication of a decline in L-[ 3 H ]glutamate release with increasing PMD. Copyright (2001) Australian Neuroscience Society

Land Cover - Minnesota Land Cover Classification System

Data.gov (United States)

Minnesota Department of Natural Resources — Land cover data set based on the Minnesota Land Cover Classification System (MLCCS) coding scheme. This data was produced using a combination of aerial photograph...

ORNL experiments to characterize fuel release from the reactor primary containment in severe LMFBR accidents

International Nuclear Information System (INIS)

Wright, A.L.; Kress, T.S.; Smith, A.M.

1980-01-01

This paper presents results from aerosol source term experiments performed in the ORNL Aerosol Release and Transport (ART) Program sponsored by the US NRC. The tests described were performed to provide information on fuel release from an LMFBR primary containment as a result of a hypothetical core-disruptive accident (HCDA). The release path investigated in these tests assumes that a fuel/sodium bubble is formed after disassembly that transports fuel and fission products through the sodium coolant and cover gas to be relased into the reactor secondary containment. Due to the excellent heat transfer characteristics of the sodium, there is potential for large attenuation of the maximum release

CALIFA, the Calar Alto Legacy Integral Field Area survey. IV. Third public data release

Science.gov (United States)

Sánchez, S. F.; García-Benito, R.; Zibetti, S.; Walcher, C. J.; Husemann, B.; Mendoza, M. A.; Galbany, L.; Falcón-Barroso, J.; Mast, D.; Aceituno, J.; Aguerri, J. A. L.; Alves, J.; Amorim, A. L.; Ascasibar, Y.; Barrado-Navascues, D.; Barrera-Ballesteros, J.; Bekeraitè, S.; Bland-Hawthorn, J.; Cano Díaz, M.; Cid Fernandes, R.; Cavichia, O.; Cortijo, C.; Dannerbauer, H.; Demleitner, M.; Díaz, A.; Dettmar, R. J.; de Lorenzo-Cáceres, A.; del Olmo, A.; Galazzi, A.; García-Lorenzo, B.; Gil de Paz, A.; González Delgado, R.; Holmes, L.; Iglésias-Páramo, J.; Kehrig, C.; Kelz, A.; Kennicutt, R. C.; Kleemann, B.; Lacerda, E. A. D.; López Fernández, R.; López Sánchez, A. R.; Lyubenova, M.; Marino, R.; Márquez, I.; Mendez-Abreu, J.; Mollá, M.; Monreal-Ibero, A.; Ortega Minakata, R.; Torres-Papaqui, J. P.; Pérez, E.; Rosales-Ortega, F. F.; Roth, M. M.; Sánchez-Blázquez, P.; Schilling, U.; Spekkens, K.; Vale Asari, N.; van den Bosch, R. C. E.; van de Ven, G.; Vilchez, J. M.; Wild, V.; Wisotzki, L.; Yıldırım, A.; Ziegler, B.

2016-10-01

This paper describes the third public data release (DR3) of the Calar Alto Legacy Integral Field Area (CALIFA) survey. Science-grade quality data for 667 galaxies are made public, including the 200 galaxies of the second public data release (DR2). Data were obtained with the integral-field spectrograph PMAS/PPak mounted on the 3.5 m telescope at the Calar Alto Observatory. Three different spectral setups are available: I) a low-resolution V500 setup covering the wavelength range 3745-7500 Å (4240-7140 Å unvignetted) with a spectral resolution of 6.0 Å (FWHM) for 646 galaxies, II) a medium-resolution V1200 setup covering the wavelength range 3650-4840 Å (3650-4620 Å unvignetted) with a spectral resolution of 2.3 Å (FWHM) for 484 galaxies, and III) the combination of the cubes from both setups (called COMBO) with a spectral resolution of 6.0 Å and a wavelength range between 3700-7500 Å (3700-7140 Å unvignetted) for 446 galaxies. The Main Sample, selected and observed according to the CALIFA survey strategy covers a redshift range between 0.005 and 0.03, spans the color-magnitude diagram and probes a wide range of stellar masses, ionization conditions, and morphological types. The Extension Sample covers several types of galaxies that are rare in the overall galaxy population and are therefore not numerous or absent in the CALIFA Main Sample. All the cubes in the data release were processed using the latest pipeline, which includes improved versions of the calibration frames and an even further improved image reconstruction quality. In total, the third data release contains 1576 datacubes, including ~1.5 million independent spectra. Based on observations collected at the Centro Astronómico Hispano Alemán (CAHA) at Calar Alto, operated jointly by the Max-Planck-Institut für Astronomie (MPIA) and the Instituto de Astrofísica de Andalucía (CSIC).The spectra are available at http://califa.caha.es/DR3

Metal release profiles of orthodontic bands, brackets, and wires: an in vitro study.

Science.gov (United States)

Wendl, B; Wiltsche, H; Lankmayr, E; Winsauer, H; Walter, A; Muchitsch, A; Jakse, N; Wendl, M; Wendl, T

2017-11-01

The present study evaluated the temporal release of Co Cr, Mn, and Ni from the components of a typical orthodontic appliance during simulated orthodontic treatment. Several commercially available types of bands, brackets, and wires were exposed to an artificial saliva solution for at least 44 days and the metals released were quantified in regular intervals using inductively coupled plasma quadrupole mass spectrometry (ICP-MS, Elan DRC+, Perkin Elmer, USA). Corrosion products encountered on some products were investigated by a scanning electron microscope equipped with an energy dispersive X-ray microanalyzer (EDX). Bands released the largest quantities of Co, Cr, Mn, and Ni, followed by brackets and wires. Three different temporal metal release profiles were observed: (1) constant, though not necessarily linear release, (2) saturation (metal release stopped after a certain time), and (3) an intermediate release profile that showed signs of saturation without reaching saturation. These temporal metal liberation profiles were found to be strongly dependent on the individual test pieces. The corrosion products which developed on some of the bands after a 6-month immersion in artificial saliva and the different metal release profiles of the investigated bands were traced back to different attachments welded onto the bands. The use of constant release rates will clearly underestimate metal intake by the patient during the first couple of days and overestimate exposure during the remainder of the treatment which is usually several months long. While our data are consistent with heavy metal release by orthodontic materials at levels well below typical dietary intake, we nevertheless recommend the use of titanium brackets and replacement of the band with a tube in cases of severe Ni or Cr allergy.

Small-scale field test of simple earthen covers for uranium mill tailings

International Nuclear Information System (INIS)

Nielson, K.K.; Rogers, V.C.; Rich, D.C.

1983-01-01

A series of field tests has been conducted during the past year to provide benchmark data on the performance of simple, single-layer earthen covers at thee uranium tailings sites. The performance of the covers was evaluated in terms of their reduction of radon gas releases, although moisture profiles and other cover parameters were also monitored. The tests were designed to evaluate the effectiveness of local soils applied with minimum engineering design or compaction effort. The tests, therefore, tend to represent a lowest-cost, and perhaps a worst-case scenario for tailings reclamation. The field benchmark tests are part of a major research program being conducted by the US Department of Energy to develop technology for uranium tailings disposal. The present tests with simple earthen covers thus provide a comparative basis for evaluating the effectiveness of more highly-engineered systems and their proportionately higher costs. These tests were conducted on the inactive tailings piles at Salt Lake City; Mexican Hat, Utah; and Grand Junction, Colorado. The test covers were installed during the summer of 1981 (Ri81) and have been monitored during the following year. This report describes the experimental details of the cover tests, the data that were collected during the one-year monitoring period, and the conclusions that were drawn from the experiments. 5 refs., 5 figs., 13 tabs

Immobilization and release study of a red alga extract in hydrogel membranes

International Nuclear Information System (INIS)

Amaral, Renata Hage

2009-01-01

In pharmaceutical technology hydrogel is the most used among the polymeric matrices due to its wide application and functionality, primarily in drug delivery system. In view of the large advance innovations in cosmetic products, both through the introduction of new active agents as the matrices used for its controlled release, the objective of this study was to evaluate the release and immobilization of a natural active agent, the Arct'Alg in hydrogel membranes to obtain a release device for cosmetics. Arct'Alg is an aqueous extract which has excellent anti-oxidant, lipolytic, anti-inflammatory and cytostimulant action. Study on mechanical and physical-chemical properties and biocompatibility in vitro of hydrogel membranes of poly(vinyl-2- pyrrolidone) (PVP) and poly(vinyl alcohol) (PVA) obtained by ionizing radiation crosslinking have been performed. The physical-chemical characterization of polymeric matrices was carried out by gel fraction and swelling tests and biocompatibility by in vitro test of cytotoxicity by using the technique of neutral red incorporation. In the gel fraction test, both the PVP and PVA hydrogel showed a high crosslinking degree. The PVP hydrogel showed a greater percentage of swelling in relation to PVA and the cytotoxicity test of the hydrogels showed non-toxicity effect. The cytostimulation property of Arct'Alg was verified by the cytostimulation test with rabbit skin cells, it was showed an increase at about 50% of the cells when in contact with 0,5% of active agent. The hydrogel membranes prepared with 3% of Arct'Alg were subjected to the release test in an incubator at 37 degree C and aliquots collected during the test were quantified by high performance liquid chromatography (HPLC). The results obtained in the kinetics of release showed that the PVP hydrogel membranes released about 50% of Arct'Alg incorporated and the PVA hydrogel membranes at about 30%. In the cytostimulation test of released Arct'Alg, the PVP device showed an

Instant release fraction corrosion studies of commercial UO2 BWR spent nuclear fuel

Science.gov (United States)

Martínez-Torrents, Albert; Serrano-Purroy, Daniel; Sureda, Rosa; Casas, Ignasi; de Pablo, Joan

2017-05-01

The instant release fraction of a spent nuclear fuel is a matter of concern in the performance assessment of a deep geological repository since it increases the radiological risk. Corrosion studies of two different spent nuclear fuels were performed using bicarbonate water under oxidizing conditions to study their instant release fraction. From each fuel, cladded segments and powder samples obtained at different radial positions were used. The results were normalised using the specific surface area to permit a comparison between fuels and samples. Different radionuclide dissolution patterns were studied in terms of water contact availability and radial distribution in the spent nuclear fuel. The relationship between the results of this work and morphological parameters like the grain size or irradiation parameters such as the burn-up or the linear power density was studied in order to increase the understanding of the instant release fraction formation.

Extended latanoprost release from commercial contact lenses: in vitro studies using corneal models.

Directory of Open Access Journals (Sweden)

Saman Mohammadi

Full Text Available In this study, we compared, for the first time, the release of a 432 kDa prostaglandin F2a analogue drug, Latanoprost, from commercially available contact lenses using in vitro models with corneal epithelial cells. Conventional polyHEMA-based and silicone hydrogel soft contact lenses were soaked in drug solution (131 μg = ml solution in phosphate buffered saline. The drug release from the contact lens material and its diffusion through three in vitro models was studied. The three in vitro models consisted of a polyethylene terephthalate (PET membrane without corneal epithelial cells, a PET membrane with a monolayer of human corneal epithelial cells (HCEC, and a PET membrane with stratified HCEC. In the cell-based in vitro corneal epithelium models, a zero order release was obtained with the silicone hydrogel materials (linear for the duration of the experiment whereby, after 48 hours, between 4 to 6 μg of latanoprost (an amount well within the range of the prescribed daily dose for glaucoma patients was released. In the absence of cells, a significantly lower amount of drug, between 0.3 to 0.5 μg, was released, (p <0:001. The difference observed in release from the hydrogel lens materials in the presence and absence of cells emphasizes the importance of using an in vitro corneal model that is more representative of the physiological conditions in the eye to more adequately characterize ophthalmic drug delivery materials. Our results demonstrate how in vitro models with corneal epithelial cells may allow better prediction of in vivo release. It also highlights the potential of drug-soaked silicone hydrogel contact lens materials for drug delivery purposes.

In-vitro Release Study of Carvedilol Phosphate Matrix Tablets ...

African Journals Online (AJOL)

decreased while Starch 1500 and lactose monohydrate increased drug release. Drug release mechanism ... case of antihypertensive agents to maintain constant blood levels ... systems because of their low toxicity, pH- independent swelling ...

Liquid crystalline systems for transdermal delivery of celecoxib: in vitro drug release and skin permeation studies.

Science.gov (United States)

Estracanholli, Eder André; Praça, Fabíola Silva Garcia; Cintra, Ana Beatriz; Pierre, Maria Bernadete Riemma; Lara, Marilisa Guimarães

2014-12-01

Liquid crystalline systems of monoolein/water could be a promising approach for the delivery of celecoxib (CXB) to the skin because these systems can sustain drug release, improve drug penetration into the skin layers and minimize side effects. This study evaluated the potential of these systems for the delivery of CXB into the skin based on in vitro drug release and skin permeation studies. The amount of CXB that permeated into and/or was retained in the skin was assayed using an HPLC method. Polarizing light microscopy studies showed that liquid crystalline systems of monoolein/water were formed in the presence of CXB, without any changes in the mesophases. The liquid crystalline systems decreased drug release when compared to control solution. Drug release was independent of the initial water content of the systems and CXB was released from cubic phase systems, irrespective of the initial water content. The systems released the CXB following zero-order release kinetics. In vitro drug permeation studies showed that cubic phase systems allowed drug permeation and retention in the skin layers. Cubic phase systems of monoolein/water may be promising vehicles for the delivery of CXB in/through the skin because it improved CXB skin permeation compared with the control solution.

Chemical incidents resulted in hazardous substances releases in the context of human health hazards.

OpenAIRE

Palaszewska-Tkacz, Anna; Czerczak, Sławomir; Konieczko, Katarzyna

2017-01-01

Objectives: The research purpose was to analyze data concerning chemical incidents in Poland collected in 1999–2009 in terms of health hazards. Material and Methods: The data was obtained, using multimodal information technology (IT) system, from chemical incidents reports prepared by rescuers at the scene. The final analysis covered sudden events associated with uncontrolled release of hazardous chemical substances or mixtures, which may potentially lead to human exposure. Releases of uniden...

Methodological studies for deriving release criteria for liquid effluents from medical installations

International Nuclear Information System (INIS)

Shu, Jane; Comissao Nacional de Energia Nuclear; Rochedo, Elaine R.R.; Heilbron Filho, Paulo F.L.; Crispim, Verginia R.

2009-01-01

This work aims to develop a methodology for the assessment of clearance limits for the release of liquid waste arising from medical installations using radionuclides for medical diagnostic purposes in the town of Rio de Janeiro. The results will be used to assess the need to justify or to revise the current clearance values as specified in regulation CNEN-NE-6.05 - Radioactive Waste Management in Radioactive Facilities. The proposed methodology is based on the mathematical model recommended by the International Atomic Energy Agency, adapted to the observed release conditions in the study area. In order to turn the assessment as realistic as possible, two scenarios are simulated. The first scenario simulates the release to the sewage system with access to a sewer treatment stations. The second scenario simulates the releases without passing a treatment station, with direct outflow to surface water. Probabilistic assessments were performed using the Crystal Ball software. Distributions were than compared to current IAEA clearance criteria that include specific values for average and low probability scenarios. The results will be used to derive adequate clearance levels for radionuclides used in nuclear diagnostic medicine in Brazil according to the specific relevant release scenario. (author)

Idaho National Engineering Laboratory release criteria for decontamination and decommissioning

International Nuclear Information System (INIS)

Dolenc, M.R.; Case, M.J.

1986-01-01

Criteria have been developed for release of Idaho National Engineering Laboratory (INEL) facilities and land areas following decontamination and decommissioning (D and D). Decommissioning release criteria in the form of dose guidelines were proposed by the US Nuclear Regulatory Commission as early as 1980. These criteria were used on an interim basis for INEL D and D projects. However, dose guidelines alone do not adequately cover the criteria necessary to release sites for unrestricted use. In actual practice, other parameters such as pathways analyses, sampling and instrumentation techniques, and implementation procedures are required to develop the basis for unrestricted release of a site. Thus, a rigorous approach for evaluating these other parameters is needed to develop acceptable D and D release criteria. Because of the complex and sensitive nature of the dose and pathways analyses work, a thorough review by experts in those respective fields was desired. Input and support in preparing or reviewing each part of the criteria development task was solicited from several DOE field offices. Experts were identified and contracted to assist in preparing portions of the release criteria, or to serve on a peer-review committee. Thus, the entire release criteria development task was thoroughly reviewed by recognized experts from each DOE field office, to validate technical content of the INEL site-specific document

Radiological considerations of the reactor cover gas processing system at the FFTF [Fast Flux Test Facility

International Nuclear Information System (INIS)

Prevo, P.R.

1986-09-01

Radiological and environmental protection experience associated with the reactor cover gas processing system at the Fast Flux Test Facility (FFTF) has been excellent. Personnel radiation exposures received from operating and maintaining the reactor cover gas processing system have been very low, the system has remained free of radioactive particulate contamination through the first seven operating cycles (cesium contamination was detected at the end of Cycle 8A), and releases of radioactivity to the environment have been very low, well below environmental standards. This report discusses these three aspects of fast reactor cover gas purification over the first eight operating cycles of the FFTF (a duration of a little more than four years, from April 1982 through July 1986)

A new scleroglucan/borax hydrogel: swelling and drug release studies.

Science.gov (United States)

Coviello, Tommasina; Grassi, Mario; Palleschi, Antonio; Bocchinfuso, Gianfranco; Coluzzi, Gina; Banishoeib, Fateme; Alhaique, Franco

2005-01-31

The aim of the work was the characterization of a new polysaccharidic physical hydrogel, obtained from Scleroglucan (Sclg) and borax, following water uptake and dimension variations during the swelling process. Furthermore, the release of molecules of different size (Theophylline (TPH), Vitamin B12 (Vit. B12) and Myoglobin (MGB)) from the gel and from the dried system used as a matrix for tablets was studied. The increase of weight of the tablets with and without the loaded drugs was followed together with the relative variation of the dimensions. The dry matrix, in the form of tablets was capable, during the swelling process, to incorporate a relevant amount of solvent (ca. 20 g water/g dried matrix), without dissolving in the medium, leading to a surprisingly noticeable anisotropic swelling that can be correlated with a peculiar supramolecular structure of the system induced by compression. Obtained results indicate that the new hydrogel can be suitable for sustained drug release formulations. The delivery from the matrix is deeply dependent on the size of the tested model drugs. The experimental release data obtained from the gel were satisfactorily fitted by an appropriate theoretical approach and the relative drug diffusion coefficients in the hydrogel were estimated. The release profiles of TPH, Vit. B12 and MGB from the tablets have been analyzed in terms of a new mathematical approach that allows calculating of permeability values of the loaded drugs.

Fission-product release modelling in the ASTEC integral code: the status of the ELSA module

International Nuclear Information System (INIS)

Plumecocq, W.; Kissane, M.P.; Manenc, H.; Giordano, P.

2003-01-01

Safety assessment of water-cooled nuclear reactors encompasses potential severe accidents where, in particular, the release of fission products (FPs) and actinides into the reactor coolant system (RCS) is evaluated. The ELSA module is used in the ASTEC integral code to model all releases into the RCS. A wide variety of experiments is used for validation: small-scale CRL, ORNL and VERCORS tests; large-scale Phebus-FP tests; etc. Being a tool that covers intact fuel and degraded states, ELSA is being improved maximizing the use of information from degradation modelling. Short-term improvements will include some treatment of initial FP release due to intergranular inventories and implementing models for release of additional structural materials (Sn, Fe, etc.). (author)

Effect of gamma irradiation on fluoride release and antibacterial activity of resin dental materials

International Nuclear Information System (INIS)

Carvalho, Fabiola Galbiatti de; Fucio, Suzana Beatriz Portugal de; Correr-Sobrinho, Lourenco; Pascon, Fernanda Miori; Kantovitz, Kamila Rosamilia; Puppin-Rontani, Regina Maria

2009-01-01

This study evaluated the effect of gamma irradiation on fluoride release and antibacterial activity of FluroShield (FS) and Clearfil Protect Bond (CPB). Four groups were formed: G1-FS + gamma; G2-FS without gamma; G3-CPB + gamma; G4-CPB without gamma. For fluoride release analysis, 12 disks of each material were prepared and covered with nail polish, except for one side (50.4 mm 2 area). G1 and G3 were sterilized with a 14.5 KGy dose at 27 deg C for 24 h, while G2 and G4 (controls) were not sterilized and were maintained under the same time and temperature conditions. Fluoride release measurements were made in duplicate (n=6) by an ion specific electrode. The antibacterial activity of the CPB and FS against Streptococcus mutans after gamma sterilization was evaluated by the agar-disc diffusion method. The diameter of the zones of microbial growth inhibition was recorded after 48 h. Data were analyzed statistically by ANOVA and Tukey's test (alpha=5%). Gamma sterilization decreased the fluoride release of FS by approximately 50%, while CPB was not affected. There was no statistically significant difference (p>0.05) in the antibacterial effect of CPB between gamma and non-gamma sterilization groups. FS presented no antibacterial activity. Gamma irradiation decreased the fluoride release of FS, but did not affect the antibacterial activity of the studied materials. (author)

Effect of gamma irradiation on fluoride release and antibacterial activity of resin dental materials

Energy Technology Data Exchange (ETDEWEB)

Carvalho, Fabiola Galbiatti de; Fucio, Suzana Beatriz Portugal de; Correr-Sobrinho, Lourenco [Universidade Estadual de Campinas (UNICAMP), Piracicaba, SP (Brazil). Piracicaba Dental School. Dept. of Dental Materials; Pascon, Fernanda Miori; Kantovitz, Kamila Rosamilia; Puppin-Rontani, Regina Maria [Universidade Estadual de Campinas (UNICAMP), Piracicaba, SP (Brazil). Piracicaba Dental School. Dept. of Pedriatric Dentistry], e-mail: rmpuppin@fop.unicamp.br

2009-07-01

This study evaluated the effect of gamma irradiation on fluoride release and antibacterial activity of FluroShield (FS) and Clearfil Protect Bond (CPB). Four groups were formed: G1-FS + gamma; G2-FS without gamma; G3-CPB + gamma; G4-CPB without gamma. For fluoride release analysis, 12 disks of each material were prepared and covered with nail polish, except for one side (50.4 mm{sup 2} area). G1 and G3 were sterilized with a 14.5 KGy dose at 27 deg C for 24 h, while G2 and G4 (controls) were not sterilized and were maintained under the same time and temperature conditions. Fluoride release measurements were made in duplicate (n=6) by an ion specific electrode. The antibacterial activity of the CPB and FS against Streptococcus mutans after gamma sterilization was evaluated by the agar-disc diffusion method. The diameter of the zones of microbial growth inhibition was recorded after 48 h. Data were analyzed statistically by ANOVA and Tukey's test (alpha=5%). Gamma sterilization decreased the fluoride release of FS by approximately 50%, while CPB was not affected. There was no statistically significant difference (p>0.05) in the antibacterial effect of CPB between gamma and non-gamma sterilization groups. FS presented no antibacterial activity. Gamma irradiation decreased the fluoride release of FS, but did not affect the antibacterial activity of the studied materials. (author)

Five-year performance monitoring of a high-density polyethylene (HDPE) cover system at a reclaimed mine waste rock pile in the Sydney Coalfield (Nova Scotia, Canada).

Science.gov (United States)

Power, Christopher; Ramasamy, Murugan; MacAskill, Devin; Shea, Joseph; MacPhee, Joseph; Mayich, David; Baechler, Fred; Mkandawire, Martin

2017-12-01

Cover systems are commonly placed over waste rock piles (WRPs) to limit atmospheric water and oxygen ingress and control the generation and release of acid mine drainage (AMD) to the receiving environment. Although covers containing geomembranes such as high-density polyethylene (HDPE) exhibit the attributes to be highly effective, there are few, if any, published studies monitoring their performance at full-scale WRPs. In 2011, a HDPE cover was installed over the Scotchtown Summit WRP in Nova Scotia, Canada, and extensive field performance monitoring was conducted over the next five years. A range of parameters within the atmosphere, cover, waste rock, groundwater and surface water, were monitored and integrated into a comprehensive hydrogeochemical conceptual model to assess (i) atmospheric ingress to the waste rock, (ii) waste rock acidity and depletion and (iii) evolution of groundwater and surface water quality. Results demonstrate that the cover is effective and meeting site closure objectives. Depletion in oxygen influx resulted in slower sulphide oxidation and AMD generation, while a significant reduction in water influx (i.e. 512 to 50 mm/year) resulted in diminished AMD release. Consistent improvements in groundwater quality (decrease in sulphate and metals; increase in pH) beneath and downgradient of the WRP were observed. Protection and/or significant improvement in surface water quality was evident in all surrounding watercourses due to the improved groundwater plume and elimination of contaminated runoff over previously exposed waste rock. A variably saturated flow and contaminant transport model is currently being developed to predict long-term cover system performance.

Sensitivity of selected landscape pattern metrics to land-cover misclassification and differences in land-cover composition

Science.gov (United States)

James D. Wickham; Robert V. O' Neill; Kurt H. Riitters; Timothy G. Wade; K. Bruce Jones

1997-01-01

Calculation of landscape metrics from land-cover data is becoming increasingly common. Some studies have shown that these measurements are sensitive to differences in land-cover composition, but none are known to have tested also their a sensitivity to land-cover misclassification. An error simulation model was written to test the sensitivity of selected land-scape...

Fission gas and iodine release measured in IFA-430 up to 15 GWd/t UO2 burnup

International Nuclear Information System (INIS)

Appelhans, A.D.; Turnbull, J.A.; White, R.J.

1983-01-01

The release of fission products from fuel pellets to the fuel-cladding gap is dependent on the fuel temperature, the power (fission rate) and the burnup (fuel structure). As part of the US Nuclear Regulatory Commission's Fuel Behavior Program, EG and G Idaho, Inc., is conducting fission product release studies in the Heavy Boiling Water Reactor in Halden, Norway. This paper presents a summary of the results up to December, 1982. The data cover fuel centerline temperatures ranging from 700 to 1500 0 C for average linear heat ratings of 16 to 35 kW/m. The measurements have been performed for the period between 4.2 and 14.8 GWd/t UO 2 of burnup of the Instrumented Fuel Assembly 430 (IFA-430). The measurement program has been directed toward quantifying the release of the short-lived radioactive noble gases and iodines

Heparin release from thermosensitive polymer coatings: in vivo studies

NARCIS (Netherlands)

Gutowska, Anna; Bae, You Han; Jacobs, Harvey; Mohammad, Fazal; Mix, Donald; Feijen, Jan; Kim, Sung Wan

1995-01-01

Biomer/poly(N-isopropylacrylamide)/[poly(NiPAAm)] thermosensitive polymer blends were prepared and their application as heparin-releasing polymer coatings for the prevention of surface-induced thrombosis was examined. The advantage of using poly(NiPAAm)-based coatings as heparin-releasing polymers

Diurnal and Seasonal Variations of Eddy-Covariance Carbon Dioxide Fluxes Above an Urban Wetland, Partitioned by Vegetation Cover

Science.gov (United States)

Schafer, K. V.; Duman, T.

2017-12-01

The New Jersey Meadowlands are an urban brackish marsh with a long history of human activity causing disturbances and alterations. Carbon emissions were measured from two sites in the Meadowlands, a natural site and a restored site, using eddy-covariance (EC) from 2014 to 2016. At each site, the EC towers were placed at the interface of two vegetation covers, allowing capturing this aspect of the wetland's heterogeneity. Using footprint modeling and light response curves we were able to partition measured fluxes between vegetation cover types and compare CO2 fluxes from patches of invasive versus native wetland vegetation communities. We show that further separating the data into seasonal and diurnal fluxes reveals patterns in CO2 fluxes that allow determining the nature of each vegetation cover as a source or sink for CO2. Our results also show that CO2 emissions from the restored wetland are significantly higher than the natural wetland. Areas of invasive Phragmites australis at the natural site had the lowest CO2 release rates during winter. These were consistently lower in magnitude than summer daytime uptake, therefore making this part of the wetland a CO2 sink. Areas planted with native Spartina alterniflora at the restored site had the largest uptake during daytime, therefore seemingly justifying restoration activities. However, they also had the highest emission rates during summer nighttime, and therefore the daily summer net uptake was not the highest compared with other vegetation covers. Furthermore, emissions from the restored site during winter were larger compared to the natural site, indicating that restoration activities might have led to a significant increase of carbon release from the wetland. Thus, during the study period the restored wetland acted as a carbon source.

Smoking-induced dopamine release studied with [{sup 11}C]raclopride PET

Energy Technology Data Exchange (ETDEWEB)

Kim, Yu Kyeong; Cho, Sang Soo; Lee, Do Hoon [Seoul National University College of Medicine, Seoul (Korea, Republic of)] (and others)

2005-07-01

It has been postulated that dopamine release in the striatum underlies the reinforcing properties of nicotine. Substantial evidence in the animal studies demonstrates that nicotine interacts with and regulates the activation of the dopaminergic neuron. The aim of this study was to visualize the dopamine release by smoking in human brain using PET scan with [{sup 11}C]raclopride. Four male non-smokers or ex-smokers with an abstinence period longer than 1 year (mean age of 24.3{+-}2.6 years) were enrolled in this study. Dopamine D2 receptor radioligand, [{sup 11}C]raclopride was administrated with bolus-plus-constant infusion. Dynamic PET was performed during 120 minutes (3x20s, 2x60s, 2x120s, 1x180s and 22x300s). Following the 50 minute-scanning, subjects smoked a cigarette containing 1 mg of nicotine while in the scanner. Blood samples for the measurements of plasma nicotine levels were collected at 0, 5, 10, 15, 20, 25, 30, 45, 60, and 90 minute after smoking. Regions for striatal structures were drawn on the coronal summed PET images guided with co-registered MRI. Binding potential, calculated as striatal-cerebellar/cerebellar activity, was measured under equilibrium condition at baseline and smoking session. The mean change in binding potential between the baseline and smoking in caudate, Putamen and ventral striatum was 3.7 % , 4.0 % and 8.6 %, respectively. This indicated the striatal dopamine release by smoking. The reduction in binding potential in the ventral striatum was significantly correlated with the cumulated plasma level of the nicotine (r{sup 2}=0.91, p=0.04). These data demonstrate that in vivo imaging with [{sup 11}C]raclopride PET could measure nicotine-induced dopamine release in the human brain, which has a significant positive correlation with the amount of nicotine administered by smoking.

Fluxgate magnetorelaxometry: a new approach to study the release properties of hydrogel cylinders and microspheres.

Science.gov (United States)

Wöhl-Bruhn, S; Heim, E; Schwoerer, A; Bertz, A; Harling, S; Menzel, H; Schilling, M; Ludwig, F; Bunjes, H

2012-10-15

Hydrogels are under investigation as long term delivery systems for biomacromolecules as active pharmaceutical ingredients. The release behavior of hydrogels can be tailored during the fabrication process. This study investigates the applicability of fluxgate magnetorelaxometry (MRX) as a tool to characterize the release properties of such long term drug delivery depots. MRX is based on the use of superparamagnetic core-shell nanoparticles as model substances. The feasibility of using superparamagnetic nanoparticles to study the degradation of and the associated release from hydrogel cylinders and hydrogel microspheres was a major point of interest. Gels prepared from two types of photo crosslinkable polymers based on modified hydroxyethylstarch, specifically hydroxyethyl starch-hydroxyethyl methacrylate (HES-HEMA) and hydroxyethyl starch-polyethylene glycol methacrylate (HES-P(EG)(6)MA), were analyzed. MRX analysis of the incorporated nanoparticles allowed to evaluate the influence of different crosslinking conditions during hydrogel production as well as to follow the increase in nanoparticle mobility as a result of hydrogel degradation during release studies. Conventional release studies with fluorescent markers (half-change method) were performed for comparison. MRX with superparamagnetic nanoparticles as model substances is a promising method to analyze pharmaceutically relevant processes such as the degradation of hydrogel drug carrier systems. In contrast to conventional release experiments MRX allows measurements in closed vials (reducing loss of sample and sampling errors), in opaque media and at low magnetic nanoparticle concentrations. Magnetic markers possess a better long-term stability than fluorescent ones and are thus also promising for the use in in vivo studies. Copyright © 2012 Elsevier B.V. All rights reserved.

Preliminary studies of plasma growth hormone releasing activity during medical therapy of acromegaly

International Nuclear Information System (INIS)

Hagen, T.C.; Lawrence, A.M.; Kirsteins, L.

1978-01-01

The in vitro growth hormone releasing activity of plasma obtained from six acromegalic subjects was measured before and during therapy. In five subjects, plasmas were obtained before and during successful medical therapy with medroxyprogesterone acetate (MPA). The sixth subject was sampled before and after transphenoidal Sr 90 -induced hypopituitarism. All subjects had a decrement in fasting growth hormone levels with respective therapies (29-88%). The in vitro growth hormone released from Rhesus monkey anterior pituitaries was assessed after incubating one lateral half in control plasma (pre-therapy) and the contralateral pituitary half in plasma obtained during or after therapy. Studies with plasmas obtained from the five patients successfully treated with MPA showed a decrease in growth hormone releasing activity during therapy in all (18-57%). Plasma obtained after Sr 90 pituitary ablation in the sixth subject had 35% more growth hormone releasing activity than obtained before therapy. These results suggest that active acromegalics who respond to MPA with significantly lowered growth hormone levels may actually achieve this response because of a decrease in growth hormone releasing factor measured peripherally. The opposite response in one acromegalic subject, following Sr 90 pituitary ablation and hypopituitarism, suggests that growth hormone releasing factor secretion may increase when growth hormone levels are lowered by ablative therapy. (orig.) [de

Functionalized mesoporous materials for adsorption and release of different drug molecules: A comparative study

International Nuclear Information System (INIS)

Wang Gang; Otuonye, Amy N.; Blair, Elizabeth A.; Denton, Kelley; Tao Zhimin; Asefa, Tewodros

2009-01-01

The adsorption capacity and release properties of mesoporous materials for drug molecules can be improved by functionalizing their surfaces with judiciously chosen organic groups. Functionalized ordered mesoporous materials containing various types of organic groups via a co-condensation synthetic method from 15% organosilane and by post-grafting organosilanes onto a pre-made mesoporous silica were synthesized. Comparative studies of their adsorption and release properties for various model drug molecules were then conducted. Functional groups including 3-aminopropyl, 3-mercaptopropyl, vinyl, and secondary amine groups were used to functionalize the mesoporous materials while rhodamine 6G and ibuprofen were utilized to investigate the materials' relative adsorption and release properties. The self-assembly of the mesoporous materials was carried out in the presence of cetyltrimethylammonium bromide (CTAB) surfactant, which produced MCM-41 type materials with pore diameters of ∼2.7-3.3 nm and moderate to high surface areas up to ∼1000 m 2 /g. The different functional groups introduced into the materials dictated their adsorption capacity and release properties. While mercaptopropyl and vinyl functionalized samples showed high adsorption capacity for rhodamine 6G, amine functionalized samples exhibited higher adsorption capacity for ibuprofen. While the diffusional release of ibuprofen was fitted on the Fickian diffusion model, the release of rhodamine 6G followed Super Case-II transport model. - Graphical abstract: The adsorption capacity and release properties of mesoporous materials for various drug molecules are tuned by functionalizing the surfaces of the materials with judiciously chosen organic groups. This work reports comparative studies of the adsorption and release properties of functionalized ordered mesoporous materials containing different hydrophobic and hydrophilic groups that are synthesized via a co-condensation and post-grafting methods for

Studies on renin release in vitro

DEFF Research Database (Denmark)

Skøtt, O

1989-01-01

1) Measurements of renin secretion from single arterioles at time intervals down to 20 seconds showed that the renin secretion is episodic, the amount of renin released during each episode corresponding to the estimated content of one secretory granule. 2) A decrease in osmolality elicits episodi...

Controlled-release tablet formulation of isoniazid.

Science.gov (United States)

Jain, N K; Kulkarni, K; Talwar, N

1992-04-01

Guar (GG) and Karaya gums (KG) alone and in combination with hydroxy-propylmethylcellulose (HPMC) were evaluated as release retarding materials to formulate a controlled-release tablet dosage form of isoniazid (1). In vitro release of 1 from tablets followed non-Fickian release profile with rapid initial release. Urinary excretion studies in normal subjects showed steady-state levels of 1 for 13 h. In vitro and in vivo data correlated (r = 0.9794). The studies suggested the potentiality of GG and KG as release retarding materials in formulating controlled-release tablet dosage forms of 1.

National Land Cover Database (NLCD) Land Cover Collection

Data.gov (United States)

U.S. Geological Survey, Department of the Interior — The National Land Cover Database (NLCD) Land Cover Collection is produced through a cooperative project conducted by the Multi-Resolution Land Characteristics (MRLC)...

Citizen science land cover classification based on ground and satellite imagery: Case study Day River in Vietnam

Science.gov (United States)

Nguyen, Son Tung; Minkman, Ellen; Rutten, Martine

2016-04-01

Citizen science is being increasingly used in the context of environmental research, thus there are needs to evaluate cognitive ability of humans in classifying environmental features. With the focus on land cover, this study explores the extent to which citizen science can be applied in sensing and measuring the environment that contribute to the creation and validation of land cover data. The Day Basin in Vietnam was selected to be the study area. Different methods to examine humans' ability to classify land cover were implemented using different information sources: ground based photos - satellite images - field observation and investigation. Most of the participants were solicited from local people and/or volunteers. Results show that across methods and sources of information, there are similar patterns of agreement and disagreement on land cover classes among participants. Understanding these patterns is critical to create a solid basis for implementing human sensors in earth observation. Keywords: Land cover, classification, citizen science, Landsat 8

Improvement of waste release control in French NPP

International Nuclear Information System (INIS)

Samson, T.; Lucquin, E.; Dupin, M.; Florence, D.; Grisot, M.

2002-01-01

The new waste release control in French NPP is more restrictive than the old one and needs heavy investment to bring plants to compliance with it. The great evolutions are a chemical follow up on more chemicals with a higher measurement frequency and with lower maximum concentrations and a specific measurement of carbon 14. Regarding radioactive releases, a new counting has been settled and activity of carbon 14 release is now measured and no longer calculated. The evolution of the French regulation leads to develop specific procedures and analytical techniques in chemistry and in radiochemistry (UV spectrometric methods, carbon 14 measurements,..) EDF NPP operators have launched a voluntarist process to reduce their releases since the beginning and before the evolution of the regulation. EDF priorities in terms of environment care lead henceforth to implement a global optimisation of the impact for a better control of releases. The new regulation will help EDF to reach its goals because it covers all the aspects in one administrative document: it is seen as a real simplification and a clarification towards public. In addition, this new regulation fits in with international practices which will allow an easier comparison of results between EDF and foreign NPP. These big environmental concerns lead EDF to create a national dedicated laboratory (LAMEN) in charge of developing specific measurement procedures to be implemented either by NPP or by sub-contractor laboratories. (authors)

Improvement of waste release control in French NPP

Energy Technology Data Exchange (ETDEWEB)

Samson, T.; Lucquin, E.; Dupin, M. [EDF/GDL (France); Florence, D. [EDF/GENV (France); Grisot, M. [EDF/CNPE Saint Laurent (France)

2002-07-01

The new waste release control in French NPP is more restrictive than the old one and needs heavy investment to bring plants to compliance with it. The great evolutions are a chemical follow up on more chemicals with a higher measurement frequency and with lower maximum concentrations and a specific measurement of carbon 14. Regarding radioactive releases, a new counting has been settled and activity of carbon 14 release is now measured and no longer calculated. The evolution of the French regulation leads to develop specific procedures and analytical techniques in chemistry and in radiochemistry (UV spectrometric methods, carbon 14 measurements,..) EDF NPP operators have launched a voluntarist process to reduce their releases since the beginning and before the evolution of the regulation. EDF priorities in terms of environment care lead henceforth to implement a global optimisation of the impact for a better control of releases. The new regulation will help EDF to reach its goals because it covers all the aspects in one administrative document: it is seen as a real simplification and a clarification towards public. In addition, this new regulation fits in with international practices which will allow an easier comparison of results between EDF and foreign NPP. These big environmental concerns lead EDF to create a national dedicated laboratory (LAMEN) in charge of developing specific measurement procedures to be implemented either by NPP or by sub-contractor laboratories. (authors)

SRTM Data Release for Africa, Colored Height

Science.gov (United States)

2004-01-01

This color shaded relief image shows the extent of digital elevation data for Africa recently released by the Shuttle Radar Topography Mission (SRTM). This release includes data for all of the continent, plus the island of Madagascar and the Arabian Peninsula. SRTM flew on board the Space Shuttle Endeavour in February 2000 and used an interferometric radar system to map the topography of Earth's landmass between latitudes 56 degrees south and 60 degrees north. The data were processed into geographic 'tiles,' each of which represents one by one degree of latitude and longitude. A degree of latitude measures 111 kilometers (69 miles) north-south, and a degree of longitude measures 111 kilometers or less east-west, decreasing away from the equator. The data are being released to the public on a continent-by-continent basis. This Africa segment includes 3256 tiles, almost a quarter of the total data set. Previous releases covered North America, South America and Eurasia. Forthcoming releases will include Australia plus an 'Islands' release for those islands not included in the continental releases. Together these data releases constitute the world's first high-resolution, near-global elevation model. The resolution of the publicly released data is three arcseconds (1/1,200 of a degree of latitude and longitude), which is about 90 meters (295 feet). Coverage in the current data release extends from 35 degrees north latitude at the southern edge of the Mediterranean to the very tip of South Africa, encompassing a great diversity of landforms. The northern part of the continent consists of a system of basins and plateaus, with several volcanic uplands whose uplift has been matched by subsidence in the large surrounding basins. Many of these basins have been infilled with sand and gravel, creating the vast Saharan lands. The Atlas Mountains in the northwest were created by convergence of the African and Eurasian tectonic plates. The geography of the central latitudes of

Investigating the in vitro drug release kinetics from controlled release diclofenac potassium-ethocel matrix tablets and the influence of co-excipients on drug release patterns.

Science.gov (United States)

Shah, Shefaat Ullah; Shah, Kifayat Ullah; Rehman, Asimur; Khan, Gul Majid

2011-04-01

The objective of the study was to formulate and evaluate controlled release polymeric tablets of Diclofenac Potassium for the release rate, release patterns and the mechanism involved in the release process of the drug. Formulations with different types and grades of Ethyl Cellulose Ether derivatives in several drug-to-polymer ratios (D:P) were compressed into tablets using the direct compression method. In vitro drug release studies were performed in phosphate buffer (pH 7.4) as dissolution medium by using USP Method-1 (Rotating Basket Method). Similarity factor f2 and dissimilarity factor f1 were applied for checking the similarities and dissimilarities of the release profiles of different formulations. For the determination of the release mechanism and drug release kinetics various mathematical/kinetic models were employed. It was found that all of the Ethocel polymers could significantly slow down the drug release rate with Ethocel FP polymers being the most efficient, especially at D:P ratios of 10:03 which lead towards the achievement of zero or near zero order release kinetics.

Studies on Arsenic Release and its Mitigation from Tailings Dam ...

African Journals Online (AJOL)

Studies on Arsenic Release and its Mitigation from Tailings Dam Using Nanomagnetite Particles. ... Ghana Mining Journal ... Abstract. Knowledge of the geochemistry of As in tailings material after beneficiation of gold-bearing sulphidic ores is necessary to comprehend the nature, stability and mobilization of As into the ...

Surfacing behavior and gas release of the physostome sprat (Sprattus sprattus) in ice-free and ice-covered waters

KAUST Repository

Solberg, Ingrid; Kaartvedt, Stein

2013-01-01

Upward-facing echosounders that provided continuous, long-term measurements were applied to address the surfacing behavior and gas release of the physostome sprat (Sprattus sprattus) throughout an entire winter in a 150-m-deep Norwegian fjord

The UKIRT Hemisphere Survey: definition and J-band data release

Science.gov (United States)

Dye, S.; Lawrence, A.; Read, M. A.; Fan, X.; Kerr, T.; Varricatt, W.; Furnell, K. E.; Edge, A. C.; Irwin, M.; Hambly, N.; Lucas, P.; Almaini, O.; Chambers, K.; Green, R.; Hewett, P.; Liu, M. C.; McGreer, I.; Best, W.; Zhang, Z.; Sutorius, E.; Froebrich, D.; Magnier, E.; Hasinger, G.; Lederer, S. M.; Bold, M.; Tedds, J. A.

2018-02-01

This paper defines the UK Infra-Red Telescope (UKIRT) Hemisphere Survey (UHS) and release of the remaining ∼12 700 deg2 of J-band survey data products. The UHS will provide continuous J- and K-band coverage in the Northern hemisphere from a declination of 0° to 60° by combining the existing Large Area Survey, Galactic Plane Survey and Galactic Clusters Survey conducted under the UKIRT Infra-red Deep Sky Survey (UKIDSS) programme with this new additional area not covered by UKIDSS. The released data include J-band imaging and source catalogues over the new area, which, together with UKIDSS, completes the J-band UHS coverage over the full ∼17 900 deg2 area. 98 per cent of the data in this release have passed quality control criteria. The remaining 2 per cent have been scheduled for re-observation. The median 5σ point source sensitivity of the released data is 19.6 mag (Vega). The median full width at half-maximum of the point spread function across the data set is 0.75 arcsec. In this paper, we outline the survey management, data acquisition, processing and calibration, quality control and archiving as well as summarizing the characteristics of the released data products. The data are initially available to a limited consortium with a world-wide release scheduled for 2018 August.

Antibiotic-loaded acrylic bone cements: An in vitro study on the release mechanism and its efficacy

Energy Technology Data Exchange (ETDEWEB)

Miola, Marta, E-mail: marta.miola@polito.it [Applied Science and Technology Department, Politecnico di Torino (Italy); Bistolfi, Alessandro [Department of Orthopaedics, Traumatology and HM, University of Turin (Italy); AO CTO, M Adelaide Hospital, Turin (Italy); Valsania, Maria Carmen; Bianco, Carlotta [Department of Orthopaedics, Traumatology and HM, University of Turin (Italy); Fucale, Giacomo [Chemical, Clinical and Microbiological Analyses Dept., CTO, Turin (Italy); Verné, Enrica [Applied Science and Technology Department, Politecnico di Torino (Italy)

2013-07-01

An in vitro study was carried out in order to investigate the antibiotic release mechanism and the antibacterial properties of commercially (Palacos® R + G and Palacos® LV + G) and manually (Palacos® R + GM and Palacos® LV + GM) blended gentamicin-loaded bone cements. Samples were characterized by means of scanning electron microscopy (SEM) and compression strength was evaluated. The antibiotic release was investigated by dipping sample in simulated body fluid (SBF) and periodically analyzing the solution by means of high pressure liquid chromatography (HPLC). Different antibacterial tests were performed to investigate the possible influence of blending technique on antibacterial properties. Only some differences were observed between gentamicin manually added and commercial ones, in the release curves, while the antibacterial effect and the mechanical properties seem to not feel the blending technique. Highlights: • The efficacy of commercially and manually mixed antibiotic-loaded cements is studied. • Exhaustive mechanical, drug release and antibacterial studies are carried out. • The blending technique does not affect the antibacterial and mechanical properties. • The blending process influences only the release curve, not the released drug amount.

Antibiotic-loaded acrylic bone cements: An in vitro study on the release mechanism and its efficacy

International Nuclear Information System (INIS)

Miola, Marta; Bistolfi, Alessandro; Valsania, Maria Carmen; Bianco, Carlotta; Fucale, Giacomo; Verné, Enrica

2013-01-01

An in vitro study was carried out in order to investigate the antibiotic release mechanism and the antibacterial properties of commercially (Palacos® R + G and Palacos® LV + G) and manually (Palacos® R + GM and Palacos® LV + GM) blended gentamicin-loaded bone cements. Samples were characterized by means of scanning electron microscopy (SEM) and compression strength was evaluated. The antibiotic release was investigated by dipping sample in simulated body fluid (SBF) and periodically analyzing the solution by means of high pressure liquid chromatography (HPLC). Different antibacterial tests were performed to investigate the possible influence of blending technique on antibacterial properties. Only some differences were observed between gentamicin manually added and commercial ones, in the release curves, while the antibacterial effect and the mechanical properties seem to not feel the blending technique. Highlights: • The efficacy of commercially and manually mixed antibiotic-loaded cements is studied. • Exhaustive mechanical, drug release and antibacterial studies are carried out. • The blending technique does not affect the antibacterial and mechanical properties. • The blending process influences only the release curve, not the released drug amount

Implementation of forest cover and carbon mapping in the Greater Mekong subregion and Malaysia project - A case study of Thailand

Science.gov (United States)

Pungkul, S.; Suraswasdi, C.; Phonekeo, V.

2014-02-01

The Great Mekong Subregion (GMS) contains one of the world's largest tropical forests and plays a vital role in sustainable development and provides a range of economic, social and environmental benefits, including essential ecosystem services such as climate change mitigation and adaptation. However, the forest in this Subregion is experiencing deforestation rates at high level due to human activities. The reduction of the forest area has negative influence to the environmental and natural resources issues, particularly, more severe disasters have occurred due to global warming and the release of the greenhouse gases. Therefore, in order to conduct forest management in the Subregion efficiently, the Forest Cover and Carbon Mapping in Greater Mekong Subregion and Malaysia project was initialized by the Asia-Pacific Network for Sustainable Forest Management and Rehabilitation (APFNet) with the collaboration of various research institutions including Institute of Forest Resource Information Technique (IFRIT), Chinese Academy of Forestry (CAF) and the countries in Sub region and Malaysia comprises of Cambodia, the People's Republic of China (Yunnan province and Guangxi province), Lao People's Democratic Republic, Malaysia, Myanmar, Thailand, and Viet Nam. The main target of the project is to apply the intensive use of recent satellite remote sensing technology, establishing regional forest cover maps, documenting forest change processes and estimating carbon storage in the GMS and Malaysia. In this paper, the authors present the implementation of the project in Thailand and demonstrate the result of forest cover mapping in the whole country in 2005 and 2010. The result of the project will contribute towards developing efficient tools to support decision makers to clearly understand the dynamic change of the forest cover which could benefit sustainable forest resource management in Thailand and the whole Subregion.

Cobalt release from inexpensive jewellery

DEFF Research Database (Denmark)

Thyssen, Jacob Pontoppidan; Jellesen, Morten Stendahl; Menné, Torkil

2010-01-01

. Conclusions: This study showed that only a minority of inexpensive jewellery purchased in Denmark released cobalt when analysed with the cobalt spot test. As fashion trends fluctuate and we found cobalt release from dark appearing jewellery, cobalt release from consumer items should be monitored in the future......Objectives: The aim was to study 354 consumer items using the cobalt spot test. Cobalt release was assessed to obtain a risk estimate of cobalt allergy and dermatitis in consumers who would wear the jewellery. Methods: The cobalt spot test was used to assess cobalt release from all items...

Carbon mapping of Argentine savannas: Using fractional tree cover to scale from field to region

Science.gov (United States)

González-Roglich, M.; Swenson, J. J.

2015-12-01

Programs which intend to maintain or enhance carbon (C) stocks in natural ecosystems are promising, but require detailed and spatially explicit C distribution models to monitor the effectiveness of management interventions. Savanna ecosystems are significant components of the global C cycle, covering about one fifth of the global land mass, but they have received less attention in C monitoring protocols. Our goal was to estimate C storage across a broad savanna ecosystem using field surveys and freely available satellite images. We first mapped tree canopies at 2.5 m resolution with a spatial subset of high resolution panchromatic images to then predict regional wall-to-wall tree percent cover using 30-m Landsat imagery and the Random Forests algorithms. We found that a model with summer and winter spectral indices from Landsat, climate and topography performed best. Using a linear relationship between C and % tree cover, we then predicted tree C stocks across the gradient of tree cover, explaining 87 % of the variability. The spatially explicit validation of the tree C model with field-measured C-stocks revealed an RMSE of 8.2 tC/ha which represented ~30% of the mean C stock for areas with tree cover, comparable to studies based on more advanced remote sensing methods, such as LiDAR and RADAR. Sample spatial distribution highly affected the performance of the RF models in predicting tree cover, raising concerns regarding the predictive capabilities of the model in areas for which training data is not present. The 50,000 km2 has ~41 Tg C, which could be released to the atmosphere if agricultural pressure intensifies in this semiarid savanna.

Infinity-Norm Permutation Covering Codes from Cyclic Groups

OpenAIRE

Karni, Ronen; Schwartz, Moshe

2017-01-01

We study covering codes of permutations with the $\\ell_\\infty$-metric. We provide a general code construction, which uses smaller building-block codes. We study cyclic transitive groups as building blocks, determining their exact covering radius, and showing linear-time algorithms for finding a covering codeword. We also bound the covering radius of relabeled cyclic transitive groups under conjugation.

[Process study on hysteresis of vegetation cover influencing sand-dust events].

Science.gov (United States)

Xu, Xing-Kui; Wang, Xiao-Tao; Zhang, Feng

2009-02-15

Data analysis from satellite and weather stations during 1982-2000 shows nonlinear relationship between vegetation cover and sand-dust events is present in most part of China. Vegetation cover ratio in summer can impact significantly on the frequency of sand-dust storms from winter to spring in the source regions of sand-dust events. It is not quite clear about the hysteresis that vegetation cover in summer influence sand-dust events during winter and spring. A quasi-geostrophic barotropic model is used under the condition of 3 magnitude of frictional coefficient to investigate the cause of the hysteresis. Wind velocity shows a greatest decline at 90% during 72 h as initial wind velocity is 10 m/s for magnitude of frictional coefficient between atmosphere and water surface, greatest decline at 100% during 18 h for magnitude of frictional coefficient between atmosphere and bare soil and a 100% reduction of wind speed during 1 h for magnitude of frictional coefficient between atmosphere and vegetation cover. Observation and simulation prove that residual root and stem from summervegetation are one of factors to influence sand-dust events happened during winter and spring. Air inhibition from residual root and stem is a most important reason for hysteresis that vegetation cover influence sand-dust events.

Instant release fraction corrosion studies of commercial UO{sub 2} BWR spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Martínez-Torrents, Albert, E-mail: albert.martinez@ctm.com.es [Fundació CTM Centre Tecnològic, Plaça de la Ciència 2, 08243 Manresa (Spain); Serrano-Purroy, Daniel [European Commission, DG Joint Research Centre - JRC, Directorate G - Nuclear Safety & Security, Department G.III, P.O. Box 2340, D-76125 Karlsruhe (Germany); Sureda, Rosa [Fundació CTM Centre Tecnològic, Plaça de la Ciència 2, 08243 Manresa (Spain); Casas, Ignasi [Department of Chemical Engineering, Universitat Politècnica de Catalunya – Barcelona Tech, Eduard Maristany 14, 08019 Barcelona (Spain); Pablo, Joan de [Fundació CTM Centre Tecnològic, Plaça de la Ciència 2, 08243 Manresa (Spain); Department of Chemical Engineering, Universitat Politècnica de Catalunya – Barcelona Tech, Eduard Maristany 14, 08019 Barcelona (Spain)

2017-05-15

The instant release fraction of a spent nuclear fuel is a matter of concern in the performance assessment of a deep geological repository since it increases the radiological risk. Corrosion studies of two different spent nuclear fuels were performed using bicarbonate water under oxidizing conditions to study their instant release fraction. From each fuel, cladded segments and powder samples obtained at different radial positions were used. The results were normalised using the specific surface area to permit a comparison between fuels and samples. Different radionuclide dissolution patterns were studied in terms of water contact availability and radial distribution in the spent nuclear fuel. The relationship between the results of this work and morphological parameters like the grain size or irradiation parameters such as the burn-up or the linear power density was studied in order to increase the understanding of the instant release fraction formation.

Generating a National Land Cover Dataset for Mexico at 30m Spatial Resolution in the Framework of the NALCMS Project.

Science.gov (United States)

Llamas, R. M.; Colditz, R. R.; Ressl, R.; Jurado Cruz, D. A.; Argumedo, J.; Victoria, A.; Meneses, C.

2017-12-01

The North American Land Change Monitoring System (NALCMS) is a tri-national initiative for mapping land cover across Mexico, United States and Canada, integrating efforts of institutions from the three countries. At the continental scale the group released land cover and change maps derived from MODIS image mosaics at 250m spatial resolution for 2005 and 2010. Current efforts are based on 30m Landsat images for 2010 ± 1 year. Each country uses its own mapping approach and sources for ancillary data, while ensuring that maps are produced in a coherent fashion across the continent. This paper presents the methodology and final land cover map of Mexico for the year 2010 that was later integrated into a continental map. The principal input for Mexico was the Monitoring Activity Data for Mexico (MAD-MEX) land cover map (version 4.3), derived from all available mostly cloud-free images for the year 2010. A total of 35 classes were regrouped to 15 classes of the NALCMS legend present in Mexico. Next, various issues of the automatically generated MAD-MEX land cover mosaic were corrected, such as: filling areas of no data due no cloud-free observation or gaps in Landsat 7 ETM+ images, filling inland water bodies which were left unclassified due to masking issues, relabeling isolated unclassified of falsely classified pixels, structural mislabeling due to data gaps, reclassifying areas of adjacent scenes with significant class disagreements and correcting obvious misclassifications, mostly of water and urban areas. In a second step minor missing areas and rare class snow and ice were digitized and a road network was added. A product such as NALCMS land cover map at 30m for North America is an unprecedented effort and will be without doubt an important source of information for many users around the world who need coherent land cover data over a continental domain as an input for a wide variety of environmental studies. The product release to the general public is expected

Land cover fire proneness in Europe

Directory of Open Access Journals (Sweden)

Mario Gonzalez Pereira

2014-12-01

Full Text Available Aim of study: This study aims to identify and characterize the spatial and temporal evolution of the types of vegetation that are most affected by forest fires in Europe. The characterization of the fuels is an important issue of the fire regime in each specific ecosystem while, on the other hand, fire is an important disturbance for global vegetation dynamics.Area of study: Southern European countries: Portugal, Spain, France, Italy and Greece.Material and Methods: Corine Land Cover maps for 2000 and 2006 (CLC2000, CLC2006 and burned area (BA perimeters, from 2000 to 2013 in Europe are combined to access the spatial and temporal evolution of the types of vegetation that are most affected by wild fires using descriptive statistics and Geographical Information System (GIS techniques.Main results: The spatial and temporal distribution of BA perimeters, vegetation and burnt vegetation by wild fires was performed and different statistics were obtained for Mediterranean and entire Europe, confirming the usefulness of the proposed land cover system. A fire proneness index is proposed to assess the fire selectivity of land cover classes. The index allowed to quantify and to compare the propensity of vegetation classes and countries to fire.Research highlights: The usefulness and efficiency of the land cover classification scheme and fire proneness index. The differences between northern Europe and southern Europe and among the Mediterranean region in what concerns to vegetation cover, fire incidence, area burnt in land cover classes and fire proneness between classes for the different countries.Keywords: Fire proneness; Mixed forests; Land cover/land use; Fire regime; Europe; GIS; Corine land cover. 

STUDIES ON NATURAL AND SYNTHETIC POLYMERS FOR CONTROLLED RELEASE MATRIX TABLET OF ACECLOFENAC

OpenAIRE

Abhishek S. Joshi *, Deepak A. Joshi , Avinash V. Dhobale , Sandhya S. Bundel , Vijay R. Chakote, Gunesh N. Dhembre

2018-01-01

The present study was aimed to design new oral controlled release matrix tablets of new NSAID Aceclofenac for once a day by using 10, 15, 20 and 25% of GG:HPMC and XG:HPMC mixture in the ratio 1:1 by wet granulation method. The prepared tablets subjected to in vitro drug release studies in pH 7.4 buffer solution. All the formulation meets the pre-compression and compression characteristics. All the tablets prepared with 10, 15, 20 and 25% of HPMC: XG mixture in the ratio 1:1 fails to meet the...

Forest Cover Estimation in Ireland Using Radar Remote Sensing: A Comparative Analysis of Forest Cover Assessment Methodologies

Science.gov (United States)

Devaney, John; Barrett, Brian; Barrett, Frank; Redmond, John; O`Halloran, John

2015-01-01

Quantification of spatial and temporal changes in forest cover is an essential component of forest monitoring programs. Due to its cloud free capability, Synthetic Aperture Radar (SAR) is an ideal source of information on forest dynamics in countries with near-constant cloud-cover. However, few studies have investigated the use of SAR for forest cover estimation in landscapes with highly sparse and fragmented forest cover. In this study, the potential use of L-band SAR for forest cover estimation in two regions (Longford and Sligo) in Ireland is investigated and compared to forest cover estimates derived from three national (Forestry2010, Prime2, National Forest Inventory), one pan-European (Forest Map 2006) and one global forest cover (Global Forest Change) product. Two machine-learning approaches (Random Forests and Extremely Randomised Trees) are evaluated. Both Random Forests and Extremely Randomised Trees classification accuracies were high (98.1–98.5%), with differences between the two classifiers being minimal (forest area and an increase in overall accuracy of SAR-derived forest cover maps. All forest cover products were evaluated using an independent validation dataset. For the Longford region, the highest overall accuracy was recorded with the Forestry2010 dataset (97.42%) whereas in Sligo, highest overall accuracy was obtained for the Prime2 dataset (97.43%), although accuracies of SAR-derived forest maps were comparable. Our findings indicate that spaceborne radar could aid inventories in regions with low levels of forest cover in fragmented landscapes. The reduced accuracies observed for the global and pan-continental forest cover maps in comparison to national and SAR-derived forest maps indicate that caution should be exercised when applying these datasets for national reporting. PMID:26262681

Application of drug selective electrode in the drug release study of pH-responsive microgels.

Science.gov (United States)

Tan, Jeremy P K; Tam, Kam C

2007-03-12

The colloidal phenomenon of soft particles is becoming an important field of research due to the growing interest in using polymeric system in drug delivery. Previous studies have focused on techniques that require intermediate process step such as dialysis or centrifugation, which introduces additional errors in obtaining the diffusion kinetic data. In this study, a drug selective electrode was used to directly measure the concentration of procaine hydrochloride (PrHy) released from methacrylic acid-ethyl acrylate (MAA-EA) microgel, thereby eliminating the intermediate process step. PrHy selective membrane constructed using a modified poly (vinyl chloride) (PVC) membrane and poly (ethylene-co-vinyl acetate-co-carbon monoxide) as plasticizer exhibited excellent reproducibility and stability. The response was reproducible at pH of between 3 to 8.5 and the selectivity coefficients against various organic and inorganic cations were evaluated. Drug release was conducted using the drug electrode under different pHs and the release rate increased with pH. The release behavior of the system under different pH exhibited obvious gradient release characteristics.

Study on the inside gas flow visualization of oxygen sensor cover; Kashika ni yoru O2 sensor cover nai no gas nagare hyoka

Energy Technology Data Exchange (ETDEWEB)

Hocho, S; Mitsuishi, Y; Inagaki, M [Nippon Soken, Inc., Tokyo (Japan); Hamaguchi, S; Mizusawa, K [Toyota Motor Corp., Aichi (Japan)

1997-10-01

In order to make clear the difference of the response time between the oxygen sensors with different protection covers, we visualized gas flow inside of sensor covers by means of two experimental methods: One is `Smoke Suspension Method` using liquid paraffin vapor as the smoke. With smoke suspension method, we detected the streamlines inside of the covers. The other is `Color Reaction Method` using the reaction of phenolphthalein and NH3 gas. With color reaction method, we confirmed the streamline inside of the cover and furthermore detected the difference of the response time of each sensor. 3 refs., 7 figs., 1 tab.

Snow mechanics and avalanche formation: field experiments on the dynamic response of the snow cover

Science.gov (United States)

Schweizer, Jürg; Schneebeli, Martin; Fierz, Charles; Föhn, Paul M. B.

1995-11-01

Knowledge about snow mechanics and snow avalanche formation forms the basis of any hazard mitigation measures. The crucial point is the snow stability. The most relevant mechanical properties - the compressive, tensile and shear strength of the individual snow layers within the snow cover - vary substantially in space and time. Among other things the strength of the snow layers depends strongly on the state of stress and the strain rate. The evaluation of the stability of the snow cover is hence a difficult task involving many extrapolations. To gain insight in the release mechanism of slab avalanches triggered by skiers, the skier's impact is measured with a load cell at different depths within the snow cover and for different snow conditions. The study focused on the effects of the dynamic loading and of the damping by snow compaction. In accordance with earlier finite-element (FE) calculations the results show the importance of the depth of the weak layer or interface and the snow conditions, especially the sublayering. In order to directly measure the impact force and to study the snow properties in more detail, a new instrument, called rammrutsch was developed. It combines the properties of the rutschblock with the defined impact properties of the rammsonde. The mechanical properties are determined using (i) the impact energy of the rammrutsch and (ii) the deformations of the snow cover measured with accelerometers and digital image processing of video sequences. The new method is well suited to detect and to measure the mechanical processes and properties of the fracturing layers. The duration of one test is around 10 minutes and the method seems appropriate for determining the spatial variability of the snow cover. A series of experiments in a forest opening showed a clear difference in the snow stability between sites below trees and ones in the free field of the opening.

Sustained-release of caffeine from a polymeric tablet matrix: An in vitro and pharmacokinetic study

International Nuclear Information System (INIS)

Tan, Donna; Zhao Bin; Moochhala, Shabbir; Yang Yiyan

2006-01-01

Caffeine is utilized as a stimulant to impart a desired level of alertness during certain working hours. Usually, a single dose of caffeine induces 2-3 h of alertness coupled with side effects whereas a longer effect of 8-12 h is very useful for both daily life and military action. Thus, there is a need to deliver the stimulant continuously to an individual at one time to impart an increased level of alertness for the period stated after administration. This study aimed to design a polymeric microparticle system for sustained delivery of caffeine using a polymeric matrix. Poly(ethylene oxide) (PEO) was used as the erodible matrix material and the caffeine polymeric tablets were fabricated by compression using a Graseby Specac hydraulic press. In vitro release profiles as well as the pharmacokinetics studies data were obtained. Caffeine tablets fabricated using various polymers showed a high initial burst release type profile as compared to the caffeine-PEO-tablet. The PK studies showed sustained delivery of caffeine resulted in two expected phenomena: a reduction in the initial high rate of caffeine release (burst release) as well as a reduction in the change in caffeine concentration in the systemic circulation. A simple two-component system for sustained-release caffeine formulation therefore has been achieved

Sustained-release of caffeine from a polymeric tablet matrix: An in vitro and pharmacokinetic study

Energy Technology Data Exchange (ETDEWEB)

Tan, Donna [Defence Medical and Environmental Research Institute, DSO National Laboratories (Kent Ridge), 27 Medical Drive, 12-00, Singapore 117597 (Singapore); Zhao Bin [Defence Medical and Environmental Research Institute, DSO National Laboratories (Kent Ridge), 27 Medical Drive, 12-00, Singapore 117597 (Singapore); Moochhala, Shabbir [Defence Medical and Environmental Research Institute, DSO National Laboratories (Kent Ridge), 27 Medical Drive, 12-00, Singapore 117597 (Singapore)]. E-mail: mshabbir@dso.org.sg; Yang Yiyan [Institute of Bioengineering and Nanotechnology, 31 Biopolis Way, 04-01, The Nanos, Singapore 138669 (Singapore)

2006-07-25

Caffeine is utilized as a stimulant to impart a desired level of alertness during certain working hours. Usually, a single dose of caffeine induces 2-3 h of alertness coupled with side effects whereas a longer effect of 8-12 h is very useful for both daily life and military action. Thus, there is a need to deliver the stimulant continuously to an individual at one time to impart an increased level of alertness for the period stated after administration. This study aimed to design a polymeric microparticle system for sustained delivery of caffeine using a polymeric matrix. Poly(ethylene oxide) (PEO) was used as the erodible matrix material and the caffeine polymeric tablets were fabricated by compression using a Graseby Specac hydraulic press. In vitro release profiles as well as the pharmacokinetics studies data were obtained. Caffeine tablets fabricated using various polymers showed a high initial burst release type profile as compared to the caffeine-PEO-tablet. The PK studies showed sustained delivery of caffeine resulted in two expected phenomena: a reduction in the initial high rate of caffeine release (burst release) as well as a reduction in the change in caffeine concentration in the systemic circulation. A simple two-component system for sustained-release caffeine formulation therefore has been achieved.

Influence of medical journal press releases on the quality of associated newspaper coverage: retrospective cohort study.

Science.gov (United States)

Schwartz, Lisa M; Woloshin, Steven; Andrews, Alice; Stukel, Therese A

2012-01-27

To determine whether the quality of press releases issued by medical journals can influence the quality of associated newspaper stories. Retrospective cohort study of medical journal press releases and associated news stories. We reviewed consecutive issues (going backwards from January 2009) of five major medical journals (Annals of Internal Medicine, BMJ, Journal of the National Cancer Institute, JAMA, and New England Journal of Medicine) to identify the first 100 original research articles with quantifiable outcomes and that had generated any newspaper coverage (unique stories ≥100 words long). We identified 759 associated newspaper stories using Lexis Nexis and Factiva searches, and 68 journal press releases using Eurekalert and journal website searches. Two independent research assistants assessed the quality of journal articles, press releases, and a stratified random sample of associated newspaper stories (n=343) by using a structured coding scheme for the presence of specific quality measures: basic study facts, quantification of the main result, harms, and limitations. Proportion of newspaper stories with specific quality measures (adjusted for whether the quality measure was present in the journal article's abstract or editor note). We recorded a median of three newspaper stories per journal article (range 1-72). Of 343 stories analysed, 71% reported on articles for which medical journals had issued press releases. 9% of stories quantified the main result with absolute risks when this information was not in the press release, 53% did so when it was in the press release (relative risk 6.0, 95% confidence interval 2.3 to 15.4), and 20% when no press release was issued (2.2, 0.83 to 6.1). 133 (39%) stories reported on research describing beneficial interventions. 24% mentioned harms (or specifically declared no harms) when harms were not mentioned in the press release, 68% when mentioned in the press release (2.8, 1.1 to 7.4), and 36% when no press release

Radioactive releases from a thorium-contaminated site in Wayne, New Jersey

International Nuclear Information System (INIS)

Wang, J.; Yang, J.; Merry-Libby, P.

1985-01-01

Various residues and wastes from the production of thorium and rare earths from monazite ore are buried on a hillside in Wayne, New Jersey. In addition, contaminated materials (primarily soils) from nearby vicinity properties are being consolidated onto the Wayne site. The US Department of Energy plans to stabilize all the contaminated materials on an interim basis (20 years) until funding is available to remove them to another location. In order to evaluate the effectiveness of interim stabilization measures, pre-remedial action radioactive releases are compared to estimated releases under a reference stabilization option (one meter of soil cover). Two potential pathways are examined: (1) airborne radioactive gases (thoron and radon) and particulates, and (2) seepage into the near-surface groundwater. The relative reduction of releases into the air and groundwater for the reference stabilization option is analyzed using mathematical models for radioactive gas fluxes and atmospheric dispersion as well as groundwater transport and dispersion. The consequent health implications for nearby individuals and the general population are also estimated. Health effects due to radioactive releases are estimated to be insignificant

Sustained release nimesulide microparticles: evaluation of release modifying property of ethy

International Nuclear Information System (INIS)

Khan, S.A.; Ahmed, M.; Nisar-ur-Rehman; Madni, A.U.; Aamir, M.N.; Murtaza, G.

2011-01-01

Microencapsulated controlled-release preparations of nimesulide were formulated. Microparticles were prepared by modified phase separation (non-solvent addition) technique using different ratios of ethylcellulose. The microparticles (M/sub 1/, M/sub 2/, and M/sub 3/) were yellow, free flowing and spherical in shape with the particle size varying from 93.62 +- 14.15 to 104.19 +- 18.15 mu m. The t/sub 60%/of nimesulide release from microparticles was found to be 3 +- 0.6, 5 +- 0.6 and 8 +- 0.8 h for formulations M/sub 1/, M/sub 2/, and M/sub 3/, respectively. FT-IR, XRD, and thermal analysis were done which showed that there is no interaction between the polymer and drug. The mechanism of drug release from nimesulide microparticles was studied by using Higuchi and Korsmeyer-Peppas models. The value of coefficient of determination (R/sup 2/) for M/sub 1/, M/sub 2/, and M/sub 3/ indicates anomalous and case-II transport release mechanism. The dissolution data of designed system verified its ability to maintain plasma concentration without the need of frequent dosing. The Nimesulide microparticles prolonged drug release for 12 hours or longer. Based on the results of release studies, M/sub 3/ was opted as a suitable microparticulate formulation allowing the controlled release of nimesulide over a prolonged period of time. Moreover, its encapsulation efficiency was also comparable to the other two formulations (M/sub 1/ and M/sub 2/). In conclusion, the influence of polymer concentration should be considered during formulation development. (author)

Land Cover

Data.gov (United States)

Kansas Data Access and Support Center — The Land Cover database depicts 10 general land cover classes for the State of Kansas. The database was compiled from a digital classification of Landsat Thematic...

Smoking-induced dopamine release studied with [{sup 11}C]Raclopride PET

Energy Technology Data Exchange (ETDEWEB)

Kim, Yu Kyeong; Cho, Sang Soo [Seoul National University College of Medicine, Seoul (Korea, Republic of); Lee, Do Hoon [Center for Clinical Services, National Cancer Certer, Goyang (Korea, Republic of)] (and others)

2005-10-15

It has been postulated that dopamine release in the striatum underlies the reinforcing properties of nicotine. Substantial evidence in the animal studies demonstrates that nicotine interacts with dopaminergic neuron and regulates the activation of the dopaminergic system. The aim of this study was to visualize the dopamine release by smoking in human brain using PET scan with [{sup 11}C]raclopride. Five male non-smokers or ex-smokers with an abstinence period longer than 1 year (mean age of 24.4 {+-} 1.7 years) were enrolled in this study. [{sup 1C}]raclopride, a dopamine D2 receptor radioligand, was administrated with bolus-plus-constant infusion. Dynamic PET was performed during 120 minutes (3 x 20s, 2 x 60s, 2 x 120s, 1 x 180s and 22 x 300s). Following the 50 minute-scanning, subjects smoked a cigarette containing 1 mg of nicotine while in the scanner. Blood samples for the measurement of plasma nicotine level were collected at 0, 5, 10, 15, 20, 25, 30, 45, 60, and 90 minute after smoking. Regions for striatal structures were drawn on the coronal summed PET images guided with co-registered MRI. Binding potential, calculated as (striatal-cerebellar)/cerebellar activity, was measured under equilibrium condition at baseline and smoking session. The mean decrease in binding potential of [{sup 1C}]raclopride between the baseline and smoking in caudate head, anterior putamen and ventral striatum was 4.7%, 4.0% and 7.8%, respectively. This indicated the striatal dopamine release by smoking. Of these, the reduction in binding potential in the ventral striatum was significantly correlated with the cumulated plasma level of the nicotine (Spearman's rho=0.9, {rho} =0.4). These data demonstrate that in vivo imaging with [{sup 11}C]raclopride PET could measure nicotine-induced dopamine release in the human brain, which has a significant positive correlation with the amount of nicotine administered by smoking.

Preparation and Characterization of Azadirachtin Alginate-Biosorbent Based Formulations: Water Release Kinetics and Photodegradation Study.

Science.gov (United States)

Flores-Céspedes, Francisco; Martínez-Domínguez, Gerardo P; Villafranca-Sánchez, Matilde; Fernández-Pérez, Manuel

2015-09-30

The botanical insecticide azadirachtin was incorporated in alginate-based granules to obtain controlled release formulations (CRFs). The basic formulation [sodium alginate (1.47%) - azadirachtin (0.28%) - water] was modified by the addition of biosorbents, obtaining homogeneous hybrid hydrogels with high azadirachtin entrapment efficiency. The effect on azadirachtin release rate caused by the incorporation of biosorbents such as lignin, humic acid, and olive pomace in alginate formulation was studied by immersion of the granules in water under static conditions. The addition of the biosorbents to the basic alginate formulation reduces the rate of release because the lignin-based formulation produces a slower release. Photodegradation experiments showed the potential of the prepared formulations in protecting azadirachtin against simulated sunlight, thus improving its stability. The results showed that formulation prepared with lignin provided extended protection. Therefore, this study provides a new procedure to encapsulate the botanical insecticide azadirachtin, improving its delivery and photostability.

U.S./Mexico Border environmental study toxics release inventory data, 1988--1992

Energy Technology Data Exchange (ETDEWEB)

O`Brien, R.F.; LoPresti, C.A.

1996-02-01

This is a report on industrial toxic chemical releases and transfers based on information reported to the Toxics Release Inventory (TRI), a database maintained by the USEPA. This document discusses patterns of toxic chemical releases to the atmosphere, to water, to the land, and to underground injection; and transfers of toxic chemicals to Publicly Owned Treatment Works (POTW), and for disposal, treatment and other off-site transfers during the TRI reporting years 1988--1992. Geographic coverage is limited to the US side of the ``Border Area``, the geographic area situated within 100 km of the US/Mexico international boundary. A primary purpose of this study is to provide background information that can be used in the future development of potential ``indicator variables`` for tracking environmental and public health status in the Border Area in conjunction with the implementation of the North American Free Trade Agreement (NAFTA).

Effect of the timing of tourniquet release on postoperative hematoma formation: an experimental animal study

Energy Technology Data Exchange (ETDEWEB)

Himel, H.N.; Ahmad, M.; Parmett, S.R.; Strauss, H.W.; May, J.W. Jr.

1989-04-01

There is a controversy over when to release a pneumatic tourniquet after completing a hand surgical procedure. To study this controversy, we performed a standardized operation with tourniquet inflow occlusion on both lower legs of a series of rabbits. Total tourniquet time and the procedure performed, including intraoperative Bovie electrocautery of actual and potential bleeding points identified with 2.5 X loupe magnification, were identical on the two sides, except for the method of tourniquet release. On one leg, the tourniquet was released and all new bleeding points were controlled prior to wound closure. On the other leg, the tourniquet was released after the wound had been closed and dressed. Animals were injected with technetium-99m-labeled red blood cells and scanned to measure hematoma formation. Qualitatively, we observed more label in the leg whose tourniquet was released after wound closure in 17 of the 20 animals (p less than 0.005). Quantitatively, we also measured more mean label in the leg whose tourniquet was released after the wound was closed (p less than 0.001). Tourniquet release after wound closure was associated with greater hematoma formation.

Effect of the timing of tourniquet release on postoperative hematoma formation: an experimental animal study

International Nuclear Information System (INIS)

Himel, H.N.; Ahmad, M.; Parmett, S.R.; Strauss, H.W.; May, J.W. Jr.

1989-01-01

There is a controversy over when to release a pneumatic tourniquet after completing a hand surgical procedure. To study this controversy, we performed a standardized operation with tourniquet inflow occlusion on both lower legs of a series of rabbits. Total tourniquet time and the procedure performed, including intraoperative Bovie electrocautery of actual and potential bleeding points identified with 2.5 X loupe magnification, were identical on the two sides, except for the method of tourniquet release. On one leg, the tourniquet was released and all new bleeding points were controlled prior to wound closure. On the other leg, the tourniquet was released after the wound had been closed and dressed. Animals were injected with technetium-99m-labeled red blood cells and scanned to measure hematoma formation. Qualitatively, we observed more label in the leg whose tourniquet was released after wound closure in 17 of the 20 animals (p less than 0.005). Quantitatively, we also measured more mean label in the leg whose tourniquet was released after the wound was closed (p less than 0.001). Tourniquet release after wound closure was associated with greater hematoma formation

2001 Toxic Chemical Release Inventory Emergency Planning and Community Right to Know Act SEC 313

International Nuclear Information System (INIS)

ZALOUDEK, D.E.

2002-01-01

Pursuant to section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 (EPCRA), and Executive Order 13148, Greening the Government Through Leadership in Environmental Management, the US Department of Energy has prepared and submitted a Toxic Chemical Release Inventory for the Hanford Site covering activities performed during calendar year 2001. EPCRA Section 313 requires facilities that manufacture, process, or otherwise use listed toxic chemicals in quantities exceeding established threshold levels to report total annual releases of those chemicals. During calendar year 2001, Hanford Site activities resulted in one chemical used in amounts exceeding an activity threshold. Accordingly, the Hanford Site 2001 Toxic Chemical Release Inventory, DOE/RL-2002-37, includes total annual amount of lead released to the environment, transferred to offsite locations, and otherwise managed as waste

Implementation of forest cover and carbon mapping in the Greater Mekong subregion and Malaysia project – A case study of Thailand

International Nuclear Information System (INIS)

Pungkul, S; Suraswasdi, C; Phonekeo, V

2014-01-01

The Great Mekong Subregion (GMS) contains one of the world's largest tropical forests and plays a vital role in sustainable development and provides a range of economic, social and environmental benefits, including essential ecosystem services such as climate change mitigation and adaptation. However, the forest in this Subregion is experiencing deforestation rates at high level due to human activities. The reduction of the forest area has negative influence to the environmental and natural resources issues, particularly, more severe disasters have occurred due to global warming and the release of the greenhouse gases. Therefore, in order to conduct forest management in the Subregion efficiently, the Forest Cover and Carbon Mapping in Greater Mekong Subregion and Malaysia project was initialized by the Asia-Pacific Network for Sustainable Forest Management and Rehabilitation (APFNet) with the collaboration of various research institutions including Institute of Forest Resource Information Technique (IFRIT), Chinese Academy of Forestry (CAF) and the countries in Sub region and Malaysia comprises of Cambodia, the People's Republic of China (Yunnan province and Guangxi province), Lao People's Democratic Republic, Malaysia, Myanmar, Thailand, and Viet Nam. The main target of the project is to apply the intensive use of recent satellite remote sensing technology, establishing regional forest cover maps, documenting forest change processes and estimating carbon storage in the GMS and Malaysia. In this paper, the authors present the implementation of the project in Thailand and demonstrate the result of forest cover mapping in the whole country in 2005 and 2010. The result of the project will contribute towards developing efficient tools to support decision makers to clearly understand the dynamic change of the forest cover which could benefit sustainable forest resource management in Thailand and the whole Subregion

In vitro labelled neurotransmitters release for the study of neuro toxins

International Nuclear Information System (INIS)

Camillo, Maria A.P.; Rogero, Jose R.; Troncone, Lanfranco R.P.

1995-01-01

There is an increasing concern in the replacement of in vivo by in vitro methods in Pharmacology. Looking for a method which involves the most of the physiological aspects related to neural functions, a super fusion system designed to evaluate in vitro neurotransmitter release from brain striatal tissue is here described. The method is based on the basal and stimulated release of pre-loaded tritium-labelled neurotransmitters. This procedure bears an active uptake/release function which is fairly changed by membrane polarisation state, ion channel activation and enzymatic activity, as well as other still unknown steps involved in neurotransmission. Calcium dependency of dopamine and acetylcholine release induced by high potassium depolarization or glutamate (Glu) stimulation was demonstrated employing calcium-free (+EGTA) super fusion or lanthanum/cadmium addition. Glutamate stimulation involved NMDA receptors since magnesium or MK801 blocks stimulated release. Uptake of DA and Ach was evidenced by using bupropione or hemicolinium-3. presynaptic inhibition of Ach release was evidenced by physostigmine-induced inhibitions of acetylcholinesterase. (author). 3 refs., 6 figs

Tunable release of clavam from clavam stabilized gold nanoparticles — Design, characterization and antimicrobial study

Energy Technology Data Exchange (ETDEWEB)

Manju, V. [Electrodics and Electrocatalysis Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India); Dhandapani, P. [Corrosion Materials and Protection Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu, 630006 (India); Gurusamy Neelavannan, M. [Characterization and Measurement lab, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India); Maruthamuthu, S. [Corrosion Materials and Protection Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu, 630006 (India); Berchmans, S. [Electrodics and Electrocatalysis Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India); Palaniappan, A., E-mail: palani112@gmail.com [Electrodics and Electrocatalysis Division, CSIR-Central Electrochemical Research Institute, Karaikudi, Tamilnadu 630006 (India)

2015-04-01

A facile one-step approach is developed to synthesize highly stable (up to 6 months) gold nanoparticles (GNPs) using Clavam, pharmaceutical form of amoxicillin which contains a mixture of amoxicillin and potassium salt of clavulanic acid, at room temperature (25–30 °C). The clavam stabilized GNPs are characterized using various techniques including UV–Visible, FT-IR spectrophotometry and transmission electron microscopy (TEM). Tunable release of clavam from clavam stabilized GNPs is demonstrated using intracellular concentrations of glutathione (GSH). The process is monitored using an UV–Vis spectroscopy and the amount of clavam released in terms of amoxicillin concentration is quantitatively estimated using reverse phase high performance liquid chromatographic (RP-HPLC) technique. In vitro study reveals that the clavam released from GNPs' surface was found to show a significant enhancement in antibacterial activity against Escherichia coli and the cause of enhancement is addressed. - Graphical abstract: Stable and nearly monodisperse gold nanoparticles (GNPs) are prepared at room temperature (~ 25–30 °C) using clavam; commercial form of amoxicillin antibiotic. Tunable release of clavam from clavam stabilized GNPs is demonstrated by the addition of varying concentrations of glutathione. Interactions between clavam and gold core are investigated in detail. The mechanism of enhanced antimicrobial activity of clavam released from clavam stabilized GNPs is probed. - Highlights: • Gold nanoparticles (GNPs) are prepared without reducing agent using antibiotic clavam{sup TR}. • Our work shed lights on the nature of interaction between the clavam and GNPs. • Sustained release of clavam from clavam stabilized GNPs is demonstrated using glutathione. • Antimicrobial activity of the released clavam is confirmed using various techniques. • Our study suggests that the clavam released from GNPs shows better inhibition of E. coli.

When Medical News Comes from Press Releases-A Case Study of Pancreatic Cancer and Processed Meat.

Directory of Open Access Journals (Sweden)

Joseph W Taylor

Full Text Available The media have a key role in communicating advances in medicine to the general public, yet the accuracy of medical journalism is an under-researched area. This project adapted an established monitoring instrument to analyse all identified news reports (n = 312 on a single medical research paper: a meta-analysis published in the British Journal of Cancer which showed a modest link between processed meat consumption and pancreatic cancer. Our most significant finding was that three sources (the journal press release, a story on the BBC News website and a story appearing on the 'NHS Choices' website appeared to account for the content of over 85% of the news stories which covered the meta analysis, with many of them being verbatim or moderately edited copies and most not citing their source. The quality of these 3 primary sources varied from excellent (NHS Choices, 10 of 11 criteria addressed to weak (journal press release, 5 of 11 criteria addressed, and this variance was reflected in the accuracy of stories derived from them. Some of the methods used in the original meta-analysis, and a proposed mechanistic explanation for the findings, were challenged in a subsequent commentary also published in the British Journal of Cancer, but this discourse was poorly reflected in the media coverage of the story.

Guidance for Evaluating the Safety of Experimental Releases of Mosquitoes, Emphasizing Mark-Release-Recapture Techniques.

Science.gov (United States)

Benedict, Mark Q; Charlwood, J Derek; Harrington, Laura C; Lounibos, L Philip; Reisen, William K; Tabachnick, Walter J

2018-01-01

Experimental releases of mosquitoes are performed to understand characteristics of populations related to the biology, ability to transmit pathogens, and ultimately their control. In this article, we discuss considerations related to the safety of experimental releases of living mosquitoes, applying principles of good practice in vector biology that protect human health and comfort. We describe specific factors of experimental releases of mosquitoes that we believe are critical to inform institutional biosafety committees and similar review boards to which proposals to conduct mosquito release experiments have been submitted. In this study, "experimental releases" means those that do not significantly increase vector capacity or nuisance biting relative to the unperturbed natural baseline. This document specifically does not address releases of mosquitoes for ongoing control programs or trials of new control methods for which broader assessments of risk are required. It also does not address releases of transgenic or exotic (non-native) mosquito species, both of which require particular regulatory approval. Experimental releases may include females and males and evaluation must consider their effects based on the number released, their genotype and phenotype, the environment into which they are released, and postrelease collection activities. We consider whether increases of disease transmission and nuisance biting might result from proposed experimental releases against the backdrop of natural population size variation. We recommend that experimental releases be conducted in a manner that can be reasonably argued to have insignificant negative effects. Reviewers of proposals for experimental releases should expect applicants to provide such an argument based on evidence from similar studies and their planned activities. This document provides guidance for creating and evaluating such proposals.

Intellectual disability and patient activation after release from prison: a prospective cohort study.

Science.gov (United States)

Young, J T; Cumming, C; van Dooren, K; Lennox, N G; Alati, R; Spittal, M J; Brophy, L; Preen, D B; Kinner, S A

2017-10-01

Intellectual disability and patient activation may be important drivers of inequities in health service access and health outcomes for people with intellectual disability transitioning from prison to the community. We assessed the association between intellectual disability and patient activation after prison release and examined whether this association varied, depending on whether intellectual disability was identified prior to prison release. Overall, 936 prisoners were screened for intellectual disability by using the Hayes Ability Screening Index and completed the Patient Activation Measure (PAM) within 6 weeks of prison release and again at 1, 3 and 6 months post-release. We estimated the association between intellectual disability status and PAM scores by using a multilevel linear model, adjusting for sociodemographic, behavioural, health and criminogenic factors. We used propensity score matching to estimate the impact of being identified with intellectual disability prior to release from prison on the change in mean PAM score after prison release. Compared with those who screened negative for intellectual disability, ex-prisoners who screened positive, both with and without prior identification of intellectual disability, had significantly decreased mean PAM scores [(B = -4.3; 95% CI: -6.3, -2.4) and (B = -4.5; 95% CI: -6.8, -2.3), respectively] over 6 months of follow-up. Among those who reported being identified with intellectual disability prior to release from prison, a significant increase in PAM score at the 6-month follow-up interview (B = 5.89; 95% CI: 2.35, 9.42; P = 0.001) was attributable to being identified with intellectual disability prior to release. Ex-prisoners screening positive for possible intellectual disability have decreased patient activation for at least 6 months after release from prison. However, individuals whose possible intellectual disability is unidentified appear to be particularly vulnerable. Incarceration is a

Interrelationships between soil cover and plant cover depending on land use

Directory of Open Access Journals (Sweden)

Tiina Köster

2013-05-01

Full Text Available Interrelationships between soil cover and plant cover of normally developed (or postlithogenic mineral soils are analysed on the basis of four sampling soil groups. The four-link pedo-ecological sequence of analysed soils, rendzinas → brown soils → pseudopodzolic soils → gley-podzols, forms a representative cross section in relation to the normal mineral soils of Estonia. All groups differ substantially from each other in terms of soil properties (calcareousness, acidity, nutrition conditions, profile fabric and humus cover. The primary tasks of the research were (1 to elucidate the main pedo-ecological characteristics of the four soil groups and their suitability for plant cover, (2 to evaluate comparatively soils in terms of productivity, sustainability, biodiversity and environmental protection ability and (3 to analyse possibilities for ecologically sound matching of soil cover with suitable plant cover. On the basis of the same material, the influence of land-use change on humus cover (epipedon fabric, properties of the entire soil cover and soil–plant interrelationship were also analysed. An ecosystem approach enables us to observe particularities caused by specific properties of a soil type (species, variety in biological turnover and in the formation of biodiversity.

Fluorine uptake into the human tooth from a thin layer of F-releasing material

International Nuclear Information System (INIS)

Yamamoto, H.; Nomachi, M.; Yasuda, K.; Iwami, Y.; Ebisu, S.; Komatsu, H.; Sakai, T.; Kamiya, T.

2007-01-01

Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 μm) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries

Fluorine uptake into the human tooth from a thin layer of F-releasing material

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, H. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan)]. E-mail: yhiroko@dent.osaka-u.ac.jp; Nomachi, M. [Graduate School of Science, Osaka University, Toyonaka, Osaka, 560-0043 (Japan); Yasuda, K. [Wakasa Wan Energy Research Center, Tsuruga, Fukui, 914-0192 (Japan); Iwami, Y. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Ebisu, S. [Department of Restorative Dentistry and Endodontology, Graduate School of Dentistry, Osaka University, 1-8 Yamadaoka, Suita, Osaka, 565-0871 (Japan); Komatsu, H. [Graduate School of Dental Medicine, Hokkaido University, Sapporo, Hokkaido, 060-8585 (Japan); Sakai, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan); Kamiya, T. [Advanced Radiation Technology Center, JAERI, Takasaki, Gunma, 370-1292 (Japan)

2007-07-15

Using the proton induced gamma-ray emission (PIGE) method (TIARA, Japan), we have studied fluorine (F) distribution in the human tooth under various conditions. Here, we report F uptake into the human tooth from a thin layer of F-releasing low viscous resin (FLVR). Crowns of human teeth were horizontally cut and the dentin of the cut surface was first covered with four kinds of FLVR (FL-Bond, Reactmer Bond, Xeno Bond, and Protect Liner F; thickness, 50-150 {mu}m) according to the manufacturers' instructions. Non-F-releasing and F-releasing filling resins were also hardened, on the cut surfaces of crowns covered with four kinds of FLVR thin layers. The type of the non-F-releasing filling materials used was LITE FIL IIP: G1-A (FL-Bond and LITE FIL IIP), G2-A (Reactmer Bond and LITE FIL IIP), G3-A (Xeno Bond and LITE FIL IIP), and G4-A (Protect Liner F and LITE FIL IIP). The types of F-releasing filling materials used were G1-B (FL-Bond and Beautifil), G2-B (Reactmer Bond and Reactmer Paste), G3-B (Xeno Bond and Xeno CF Paste), and G4-B (Protect Liner F and Teethmate F-1). Treatment and measurements of specimens were the same as previously reported [H. Yamamoto, M. Nomahci, K. Yasuda, Y. Iwami, S. Ebisu, N. Yamamoto, T. Sakai, T. Kamiya, Nucl. Instr. and Meth. B 210 (2003) 388]. F uptake from specimens following one month of application was estimated from 2-D maps. F penetration was observed in all teeth of G1-A-G4-A groups. The maximum values of F concentration in each tooth and F penetration depth were larger for larger F concentrations in FLVR. FLVR was useful for the F uptake into the tooth, and the F distribution near the thin layer of FLVR depended on the materials used. Between G1-A and G1-B or G4-A and G4-B, the F uptake was significantly different. We were able to obtain fundamental data, which were useful for the analysis of F transportation relating to prevention of caries.

Characterization of drug-release kinetics in trabecular bone from titania nanotube implants

Directory of Open Access Journals (Sweden)

Aw MS

2012-09-01

Full Text Available Moom Sinn Aw,1 Kamarul A Khalid,2,3 Karan Gulati,1 Gerald J Atkins,2 Peter Pivonka,4 David M Findlay,2 Dusan Losic11School of Chemical Engineering, 2Discipline of Orthopaedics and Trauma, The University of Adelaide, Adelaide, SA, Australia; 3Department of Orthopaedics, Traumatology and Rehabilitation, Faculty of Medicine, International Islamic University Malaysia, Kuantan, Pahang, Malaysia; 4Engineering Computational Biology Group, School of Computer Science and Software Engineering, The University of Western Australia, Perth, WA, AustraliaPurpose: The aim of this study was to investigate the application of the three-dimensional bone bioreactor for studying drug-release kinetics and distribution of drugs in the ex vivo cancellous bone environment, and to demonstrate the application of nanoengineered titanium (Ti wires generated with titania nanotube (TNT arrays as drug-releasing implants for local drug deliveryMethods: Nanoengineered Ti wires covered with a layer of TNT arrays implanted in bone were used as a drug-releasing implant. Viable bovine trabecular bone was used as the ex vivo bone substrate embedded with the implants and placed in the bone reactor. A hydrophilic fluorescent dye (rhodamine B was used as the model drug, loaded inside the TNT–Ti implants, to monitor drug release and transport in trabecular bone. The distribution of released model drug in the bone was monitored throughout the bone structure, and concentration profiles at different vertical (0–5 mm and horizontal (0–10 mm distances from the implant surface were obtained at a range of release times from 1 hour to 5 days.Results: Scanning electron microscopy confirmed that well-ordered, vertically aligned nanotube arrays were formed on the surface of prepared TNT–Ti wires. Thermogravimetric analysis proved loading of the model drug and fluorescence spectroscopy was used to show drug-release characteristics in-vitro. The drug release from implants inserted into bone ex

All polymer chip for amperometric studies of transmitter release from large groups of neuronal cells

DEFF Research Database (Denmark)

Larsen, Simon T.; Taboryski, Rafael

2012-01-01

We present an all polymer electrochemical chip for simple detection of transmitter release from large groups of cultured PC 12 cells. Conductive polymer PEDOT:tosylate microelectrodes were used together with constant potential amperometry to obtain easy-to-analyze oxidation signals from potassium......-induced release of transmitter molecules. The nature of the resulting current peaks is discussed, and the time for restoring transmitter reservoirs is studied. The relationship between released transmitters and potassium concentration was found to fit to a sigmoidal dose–response curve. Finally, we demonstrate...

Chemical and biological properties of phosphorus-fertilized soil under legume and grass cover (Cerrado region, Brazil

Directory of Open Access Journals (Sweden)

Marcelo Fernando Pereira Souza

2013-12-01

Full Text Available The use of cover crops has been suggested as an effective method to maintain and/or increase the organic matter content, while maintaining and/or enhancing the soil physical, chemical and biological properties. The fertility of Cerrado soils is low and, consequently, phosphorus levels as well. Phosphorus is required at every metabolic stage of the plant, as it plays a role in the processes of protein and energy synthesis and influences the photosynthetic process. This study evaluated the influence of cover crops and phosphorus rates on soil chemical and biological properties after two consecutive years of common bean. The study analyzed an Oxisol in Selvíria (Mato Grosso do Sul, Brazil, in a randomized block, split plot design, in a total of 24 treatments with three replications. The plot treatments consisted of cover crops (millet, pigeon pea, crotalaria, velvet bean, millet + pigeon pea, millet + crotalaria, and millet + velvet bean and one plot was left fallow. The subplots were represented by phosphorus rates applied as monoammonium phosphate (0, 60 and 90 kg ha-1 P2O5. In August 2011, the soil chemical properties were evaluated (pH, organic matter, phosphorus, potential acidity, cation exchange capacity, and base saturation as well as biological variables (carbon of released CO2, microbial carbon, metabolic quotient and microbial quotient. After two years of cover crops in rotation with common bean, the cover crop biomass had not altered the soil chemical properties and barely influenced the microbial activity. The biomass production of millet and crotalaria (monoculture or intercropped was highest. The biological variables were sensitive and responded to increasing phosphorus rates with increases in microbial carbon and reduction of the metabolic quotient.

Arthroscopic release using F and C method versus conventional open release method in the treatment of gluteal muscle contracture: a comparative study.

Science.gov (United States)

Rai, Saroj; Jin, Shengyang; Meng, Chunqing; Chaudhary, Nabin; Tamang, Nira; Wang, Xiaohong; Liu, Xianzhe; Wang, Hong; Yang, Shuhua

2017-03-16

Gluteal muscle contracture (GMC), a debilitating disease, usually starts in early childhood after variable dose of injections around the buttock, if left untreated it worsens gradually and persists throughout the life. Because the disease mostly affects adolescents and adults, there is always an aesthetic concerns. Purposeof the study was to introduce the arthroscopic F and C method of GMC release, and to compare its clinical efficiency with conventional open surgery in terms of clinical outcome, rate of complications, patient's satisfactions, and recurrence. Between Jan 2013 and July 2015, 75 patients received an arthroscopic release with F and C release method and 71 patients received conventional open release of GMC. Primary surgeries in 16 years or older patients were included in the study. Two groups were compared clinically using Hip Outcome Scores - Activities of Daily Living Subscale (HOS-ADL), Hip Outcome Scores - Sports Subscale (HOS-Sports), Visual Analogue Scale (VAS), and Ye et al. evaluation criteria. No statistically significant differences were observed in Hip Outcome Scores - Activities of Daily Living Subscale (HOS-ADL) (P = 0.078), Hip Outcome Scores - Sports Subscale (HOS-Sports) (P = 0.340), and Visual Analogue Scale (VAS) (P = 0.524) between the two groups. 74 (98.7%) patients in the arthroscopic surgery group had good to excellent results, whereas 69 (97.1%) patients in the conventional open surgery group had good to excellent results (P = 0.727). No statistically significant difference was observed in recurrence rate (P = 0.612). Statistically significant differences were observed in incision length, use of post-operative analgesia, post-operative off-bed activity, and hospital stay. Complications were significantly higher in the conventional open surgery group (n = 21) than in the arthroscopic surgery group (n = 10) (P = 0.016). More importantly, cosmetic satisfaction was 100% in arthroscopic release group

Decomposição e liberação de nutrientes de resíduos culturais de plantas de cobertura em argissolo vermelho-amarelo na região noroeste Fluminense (RJ Decomposition and nutrient release from cover crop residues in passion-fruit plantation

Directory of Open Access Journals (Sweden)

Antonio Carlos da Gama-Rodrigues

2007-12-01

release from cover crop residues in a passion-fruit plantation. The evaluated species were Canavalia ensiformis, Arachis pintoi, Macroptilium atropurpureum, Pueraria phaseoloides and Brachiaria brizantha. Litter decomposition was measured using nylon, 2.0 mm mesh, litter bags during 140 days. The single exponential model adjusted best for all cover crop species. Litter decay rates of Canavalia ensiformis and Arachis pintoi were significantly higher than in those of other species. The C, N, P, Ca and Mg release rates from Canavalia ensiformis residue were the highest. However, K release rate was the highest for Arachis pintoi. For all residues the K and polyphenol release rates were higher than those of the other elements. C, N, P, Ca and Mg release rates were positively correlated with litter decay rate. The litter decay rate, C, nutrients, and polyphenol release rates were regulated by litter quality. The different litter decay rates and estimated nutrient release rates indicate the potential of the use of crop residues as nutrient source of passion-fruit.

Is the press release a genre? a study of form and content

DEFF Research Database (Denmark)

Lassen, Inger

2006-01-01

; Eggins, 1994). Genre analysts who have studied press releases in particular (e.g. Frandsen et al., 1997; Jcobs, 1999) tend to share this view, but nevertheless categorize communicative events conveyed through the press release as belonging to one genre despite variation in rhetorical objectives...... biotechnological issue. In my analyses I shall discuss staging in terms of content as wll as logico-semantic relations between stages, patterns of stage combinations and their linguistic realizations with the aim of identifying variation in rhetorical objective....

Long-term stability study of Prussian blue-A quality assessment of water content and cyanide release.

Science.gov (United States)

Mohammad, A; Yang, Y; Khan, M A; Faustino, P J

2015-02-01

Prussian blue, ferric hexacyanoferrate is approved for (oral) treatment of internal contamination with radioisotopes of cesium or thallium. Cyanide makes up 35-40% of Prussian blue's molecular composition; thus, cyanide may be released during transit through the digestive tract under physiological pH conditions. The purpose of this study is to assess the long-term stability of Prussian blue drug products and active pharmaceutical ingredients and its impact on cyanide release. The study involves the determination and comparison of the loss in water content and cyanide released from Prussian blue under pH conditions that bracket human physiological exposure. Test samples of active pharmaceutical ingredient and drug product were stored for 10 years at ambient temperatures that mimic warehouse storage conditions. Water loss from Prussian blue was measured using thermogravimetric analysis. An in vitro physiological pH model that brackets gastric exposure and gastrointestinal transit was utilized for cyanide release. Prussian blue was incubated in situ at pH: 1.0, 5.0, and 7.0 @ 37°C for 1-24 h. Cyanide was measured using a validated colorimetric method by UV-Vis spectroscopy. Although the water content (quality attribute) of Prussian blue active pharmaceutical ingredient and drug product decreased by about 10.5% and 13.8%, respectively, since 2003, the cyanide release remained comparable. At pH of 7.0 for 24 h cyanide released from active pharmaceutical ingredient-1 was 21.33 ± 1.76 μg/g in 2004, and 28.45 ± 3.15 μg/g in 2013; cyanide released from drug product-1 was 21.89 ± 0.56 μg/g in 2004, and 27.31 ± 5.78 μg/g in 2013. At gastric pH of 1.0 and upper gastrointestinal pH of 5.0, the data for active pharmaceutical ingredients and drug products were also comparable in 2013. The cyanide release is still pH-dependent and follows the same trend as observed in 2003 with minimum release at pH of 5.0 and maximal release at pH of 1.0. In summary, this is the long

Assessment of the methane oxidation capacity of compacted soils intended for use as landfill cover materials

International Nuclear Information System (INIS)

Rachor, Ingke; Gebert, Julia; Groengroeft, Alexander; Pfeiffer, Eva-Maria

2011-01-01

The microbial oxidation of methane in engineered cover soils is considered a potent option for the mitigation of emissions from old landfills or sites containing wastes of low methane generation rates. A laboratory column study was conducted in order to derive design criteria that enable construction of an effective methane oxidising cover from the range of soils that are available to the landfill operator. Therefore, the methane oxidation capacity of different soils was assessed under simulated landfill conditions. Five sandy potential landfill top cover materials with varying contents of silt and clay were investigated with respect to methane oxidation and corresponding soil gas composition over a period of four months. The soils were compacted to 95% of their specific proctor density, resulting in bulk densities of 1.4-1.7 g cm -3 , reflecting considerably unfavourable conditions for methane oxidation due to reduced air-filled porosity. The soil water content was adjusted to field capacity, resulting in water contents ranging from 16.2 to 48.5 vol.%. The investigated inlet fluxes ranged from 25 to about 100 g CH 4 m -2 d -1 , covering the methane load proposed to allow for complete oxidation in landfill covers under Western European climate conditions and hence being suggested as a criterion for release from aftercare. The vertical distribution of gas concentrations, methane flux balances as well as stable carbon isotope studies allowed for clear process identifications. Higher inlet fluxes led to a reduction of the aerated zone, an increase in the absolute methane oxidation rate and a decline of the relative proportion of oxidized methane. For each material, a specific maximum oxidation rate was determined, which varied between 20 and 95 g CH 4 m -2 d -1 and which was positively correlated to the air-filled porosity of the soil. Methane oxidation efficiencies and gas profile data imply a strong link between oxidation capacity and diffusive ingress of

Interim report: Study of benzene release from Savannah River in-tank precipitation process slurry simulant

International Nuclear Information System (INIS)

Rappe, K.G.; Gauglitz, P.A.

1997-09-01

At the Savannah River Site, the in-tank precipitation (ITP) process uses sodium tetraphenylborate (NaTPB) to precipitate radioactive cesium from alkaline wastes. During this process, potassium is also precipitated to form a 4-wt% KTPB/CsTPB slurry. Residual NaTPB decomposes to form benzene, which is retained by the waste slurry. The retained benzene is also readily released from the waste during subsequent waste processing. While the release of benzene certainly poses both flammability and toxicological safety concerns, the magnitude of the hazard depends on the rate of release. Currently, the mechanisms controlling the benzene release rates are not well understood, and predictive models for estimating benzene release rates are not available. The overall purpose of this study is to obtain quantitative measurements of benzene release rates from a series of ITP slurry stimulants. This information will become a basis for developing a quantitative mechanistic model of benzene release rates. The transient benzene release rate was measured from the surface of various ITP slurry (solution) samples mixed with benzene. The benzene release rate was determined by continuously purging the headspace of a sealed sample vessel with an inert gas (nitrogen) and analyzing that purged headspace vapor for benzene every 3 minutes. The following 75-mL samples were measured for release rates: KTPB slurry with 15,000 ppm freshly added benzene that was gently mixed with the slurry, KTPB slurry homogenized (energetically mixed) with 15,000 ppm and 5,000 ppm benzene, clear and filtered KTPB salt solution saturated with benzene (with and without a pure benzene layer on top of the solution), and a slurry sample from a large demonstration experiment (DEMO slurry) containing-benzene generated in situ

Clouds cover variability in São Paulo

Directory of Open Access Journals (Sweden)

Luciana Machado de Moura

2016-11-01

Full Text Available Clouds cover observations are performed by visual inspection which determines the fraction of the sky that is overcast. However, visual observation of clouds cover is a very subjective method, and can vary significantly among observers. This study examined the variability in clouds cover over the city of São Paulo between 1961 and 2013, using clouds cover fraction data observed at the weather station operated by IAG / USP. The study also used two techniques based on visible radiance data observed by the GOES-10 satellite in order to indirectly estimate clouds cover. In order to ensure consistency, the estimated and observed cloudiness was compared with the clearness index, which is the ratio between the total solar radiation observed at the weather station and the incoming solar irradiation at the top of atmosphere. The study found consistency between the various databases that showed similar behavior in all of the seasons of the year. The largest cloudiness values occurred in the summer and lowest in the winter.

Conformable covered versus uncovered self-expandable metallic stents for palliation of malignant gastroduodenal obstruction: a randomized prospective study.

Science.gov (United States)

Lim, Sun Gyo; Kim, Jin Hong; Lee, Kee Myung; Shin, Sung Jae; Kim, Chan Gyoo; Kim, Kyung Ho; Kim, Ho Gak; Yang, Chang Heon

2014-07-01

A conformable self-expandable metallic stent was developed to overcome the limitation of previous self-expandable metallic stents. The aim of this study was to evaluate outcomes after placement of conformable covered and uncovered self-expandable metallic stents for palliation of malignant gastroduodenal obstruction. A single-blind, randomized, parallel-group, prospective study were conducted in 4 medical centres between March 2009 and July 2012. 134 patients with unresectable malignant gastroduodenal obstruction were assigned to a covered double-layered (n=66) or uncovered unfixed-cell braided (n=68) stent placement group. Primary analysis was performed to compare re-intervention rates between two groups. 120 patients were analysed (59 in the covered group and 61 in the uncovered group). Overall rates of re-intervention were not significantly different between the two groups: 13/59 (22.0%) in the covered group vs. 13/61 (21.3%) in the uncovered group, p=0.999. Stent migration was more frequent in the covered group than in the uncovered group (p=0.003). The tumour ingrowth rate was higher in the uncovered group than in the covered group (p=0.016). The rates of re-intervention did not significantly differ between the two stents. Conformable covered double-layered and uncovered unfixed-cell braided stents were associated with different patterns of stent malfunction. Copyright © 2014 Editrice Gastroenterologica Italiana S.r.l. Published by Elsevier Ltd. All rights reserved.

Parametric study of radioactive release from a breached containment

International Nuclear Information System (INIS)

Kenigsberg, A.; Hasan, D.; Elias, E.

1980-01-01

A hypothetical accident is analyzed, in which an external (out-of-plant) natural or man-made event causes a loss-of-coolant accident after penetrating the containment wall. The computer codes CONTEMPT and RELAP4 have been used to study the containment thermal-hydraulic behavior during the accident. Results are given in the form of graphs showing the thermal-hydraulic response of the containment and the profile of radioactive release to the atmosphere. The physical model and input data are discussed. 13 refs

USING PERFLUOROCARBON TRACERS FOR VERIFICATION OF CAP AND COVER SYSTEMS PERFORMANCE

International Nuclear Information System (INIS)

HEISER, J.; SULLIVAN, T.

2001-01-01

The Department of Energy (DOE) Environmental Management (EM) office has committed itself to an accelerated cleanup of its national facilities. The goal is to have much of the DOE legacy waste sites remediated by 2006. This includes closure of several sites (e.g., Rocky Flats and Fernald). With the increased focus on accelerated cleanup, there has been considerable concern about long-term stewardship issues in general, and verification and long-term monitoring (LTM) of caps and covers, in particular. Cap and cover systems (covers) are vital remedial options that will be extensively used in meeting these 2006 cleanup goals. Every buried waste site within the DOE complex will require some form of cover system. These covers are expected to last from 100 to 1000 years or more. The stakeholders can be expected to focus on system durability and sustained performance. DOE EM has set up a national committee of experts to develop a long-term capping (LTC) guidance document. Covers are subject to subsidence, erosion, desiccation, animal intrusion, plant root infiltration, etc., all of which will affect the overall performance of the cover. Very little is available in terms of long-term monitoring other than downstream groundwater or surface water monitoring. By its very nature, this can only indicate that failure of the cover system has already occurred and contaminants have been transported away from the site. This is unacceptable. Methods that indicate early cover failure (prior to contaminant release) or predict approaching cover failure are needed. The LTC committee has identified predictive monitoring technologies as a high priority need for DOE, both for new covers as well as existing covers. The same committee identified a Brookhaven National Laboratory (BNL) technology as one approach that may be capable of meeting the requirements for LTM. The Environmental Research and Technology Division (ERTD) at BNL developed a novel methodology for verifying and monitoring

Towards more physiological manipulations of hormones in field studies: comparing the release dynamics of three kinds of testosterone implants, silastic tubing, time-release pellets and beeswax.

Science.gov (United States)

Quispe, Rene; Trappschuh, Monika; Gahr, Manfred; Goymann, Wolfgang

2015-02-01

Hormone manipulations are of increasing interest in the areas of physiological ecology and evolution, because hormones are mediators of complex phenotypic changes. Often, however, hormone manipulations in field settings follow the approaches that have been used in classical endocrinology, potentially using supra-physiological doses. To answer ecological and evolutionary questions, it may be important to manipulate hormones within their physiological range. We compare the release dynamics of three kinds of implants, silastic tubing, time-release pellets, and beeswax pellets, each containing 3mg of testosterone. These implants were placed into female Japanese quail, and plasma levels of testosterone measured over a period of 30 days. Testosterone in silastic tubing led to supraphysiological levels. Also, testosterone concentrations were highly variable between individuals. Time-release pellets led to levels of testosterone that were slightly supraphysiological during the first days. Over the period of 30 days, however, testosterone concentrations were more consistent. Beeswax implants led to a physiological increase in testosterone and a relatively constant release. The study demonstrated that hormone implants in 10mm silastic tubing led to a supraphysiological peak in female quail. Thus, the use of similar-sized or even larger silastic implants in males or in other smaller vertebrates needs careful assessment. Time-release pellets and beeswax implants provide a more controlled release and degrade within the body. Thus, it is not necessary to recapture the animal to remove the implant. We propose beeswax implants as an appropriate procedure to manipulate testosterone levels within the physiological range. Hence, such implants may be an effective alternative for field studies. Copyright © 2015 Elsevier Inc. All rights reserved.

Release mechanisms from shallow engineered trenches used as repositories for radioactive wastes

International Nuclear Information System (INIS)

Locke, J.; Wood, E.

1987-05-01

This report has been written for the Department of the Environment as part of their radioactive waste management research programme. The aim has been to identify release mechanisms of radioactivity from fully engineered trenches of the LAND 2 type and, to identify the data needed for their assessment. No direct experimental work has been involved. The report starts with a brief background to UK strategy and outlines a basic disposal system. It gives reviews of existing experience of low level radioactive waste disposal from LAND 1 trenches and of UK experience of toxic waste disposal to provide a practical basis for the next section which covers the implications of identified release mechanisms on the design requirements for an engineered trench. From these design requirements and their interaction with potential site conditions (both saturated and unsaturated zone sites are considered) an assessment of radionuclide release mechanism is made. (author)

A randomized, double-blind study of hydromorphone hydrochloride extended-release tablets versus oxycodone hydrochloride extended-release tablets for cancer pain: efficacy and safety in Japanese cancer patients (EXHEAL: a Phase III study of EXtended-release HydromorphonE for cAncer pain reLief

Directory of Open Access Journals (Sweden)

Inoue S

2017-08-01

Full Text Available Satoshi Inoue,1 Yoji Saito,2 Satoru Tsuneto,3 Etsuko Aruga,4 Azusa Ide,1 Yasuyuki Kakurai5 1Clinical Development Department, R&D Division, Daiichi Sankyo, Tokyo,2Department of Anesthesiology, Faculty of Medicine, Shimane University, Shimane, 3Human Health Sciences, Graduate School of Medicine, Kyoto University, Kyoto, 4Department of Palliative Medicine, School of Medicine, Teikyo University, Tokyo, 5Biostatistics and Data Management Department, R&D Division, Daiichi Sankyo, Tokyo, Japan Background: In Japan, there are limited options for switching opioid analgesics. Hydromorphone is an opioid analgesic that is routinely used instead of morphine for cancer pain; however, it is not yet available in Japan. The aim of this study was to assess the efficacy and safety of hydromorphone (DS-7113b extended-release tablets in opioid-naïve patients with cancer pain not relieved by non-opioid analgesics.Subjects and methods: This was a multicenter, randomized, double-blind, parallel-group trial. A double-dummy method was used for blinding. Each randomized subject received either hydromorphone extended-release tablets plus placebo oxycodone hydrochloride extended-release tablets 4 mg/day (n=88 or placebo hydromorphone extended-release tablets plus oxycodone hydrochloride extended-release tablets 10 mg/day (n=93 orally for 7 days (once-daily dosing for hydromorphone and twice-daily dosing for oxycodone. The doses were adjusted as necessary. Efficacy was evaluated by change in visual analog scale (VAS score from baseline to completion of treatment.Results: The between-group difference in least squares mean changes in VAS score from baseline to completion or discontinuation of treatment was −0.4 mm (95% CI −5.9 to 5 mm by analysis of covariance where the baseline VAS score was used as a covariate. The upper limit of the 95% CI was below 10 mm, which was predefined as the noninferiority limit. This verified the noninferiority of hydromorphone tablets

Evaluating conditional release in not guilty by reason of insanity acquittees: a prospective follow-up study in Virginia.

Science.gov (United States)

Vitacco, Michael J; Vauter, Rebecca; Erickson, Steven K; Ragatz, Laurie

2014-08-01

Detailed research on treatment and risk management approaches with not guilty by reason of insanity acquittees (NGRI) during their conditional release is needed as states increasingly use community-based services for these individuals. Grounded in case law, and supported by follow-up studies demonstrating low recidivism rates, states have been encouraged in their efforts to conditionally release NGRI acquittees. The authors evaluated a state-wide sample of 127 NGRI acquittees released into the community after spending a mean of 61.63 months (SD = 76.54) in the hospital. One hundred individuals were committed to the hospital for lengthier treatment (M hospital time = 77.23 months, SD = 79.84), but 27 individuals were released to the community after a relatively short hospital stay (M hospital time = 5.60 months, SD = 3.01). Regarding release, 96 individuals (75.6%) maintained their conditional release. After evaluating a host of demographic and standardized risk data, the following variables predicted revocation on conditional release: previous failure on conditional release, nonadherence with hospital treatment, dangerousness to others, and previous violent charges. A multivariate survival analysis determined criminal behavior and previous failure on conditional release predicted time to revocation. The results of this study demonstrate the importance of considering standardized risk variables in the community-based management of forensic patients. In addition, the data are supportive of continued attempts at moving insanity acquittees from the hospital to the community via conditional release.

Mekong Land Cover Dasboard: Regional Land Cover Mointoring Systems

Science.gov (United States)

Saah, D. S.; Towashiraporn, P.; Aekakkararungroj, A.; Phongsapan, K.; Triepke, J.; Maus, P.; Tenneson, K.; Cutter, P. G.; Ganz, D.; Anderson, E.

2016-12-01

SERVIR-Mekong, a USAID-NASA partnership, helps decision makers in the Lower Mekong Region utilize GIS and Remote Sensing information to inform climate related activities. In 2015, SERVIR-Mekong conducted a geospatial needs assessment for the Lower Mekong countries which included individual country consultations. The team found that many countries were dependent on land cover and land use maps for land resource planning, quantifying ecosystem services, including resilience to climate change, biodiversity conservation, and other critical social issues. Many of the Lower Mekong countries have developed national scale land cover maps derived in part from remote sensing products and geospatial technologies. However, updates are infrequent and classification systems do not always meet the needs of key user groups. In addition, data products stop at political boundaries and are often not accessible making the data unusable across country boundaries and with resource management partners. Many of these countries rely on global land cover products to fill the gaps of their national efforts, compromising consistency between data and policies. These gaps in national efforts can be filled by a flexible regional land cover monitoring system that is co-developed by regional partners with the specific intention of meeting national transboundary needs, for example including consistent forest definitions in transboundary watersheds. Based on these facts, key regional stakeholders identified a need for a land cover monitoring system that will produce frequent, high quality land cover maps using a consistent regional classification scheme that is compatible with national country needs. SERVIR-Mekong is currently developing a solution that leverages recent developments in remote sensing science and technology, such as Google Earth Engine (GEE), and working together with production partners to develop a system that will use a common set of input data sources to generate high

Evaluation of the release behavior of the dexamethasone embedded in polycarbonate polyurethane membranes: an in vitro study

International Nuclear Information System (INIS)

Kim, Dong Hyun; Kang, Sung Gwon; Lee, Chul Gab; Park, Sang Soo; Lee, Don Haeng; Lee, Gyu Baek; Song, Ho Young

2003-01-01

To evaluate the release behavior of dexamethasone embedded in a polycarbonate polyurethane membrane. Both water-soluble and water-insoluble dexamethasone were tested, and the release behavior of five water-insoluble dexamethasone films of different thickness (78 to 211 μm) was also evaluated. The amount of dexamethasone used was 10% of the total weight of the polyurethan film mass. Each film was placed in a centrifuge tube containing 25 ml of 0.1-M neutral phosphate buffer, and the tubes were placed in a shaking incubator to quantify the amount of drug released into the buffer, absorption spectroscopy (λ max=242 nm) was employed. In the test involving water-soluble dexamethasone, 60%, of the drug was released during the first two hours of the study. Films containing water-insoluble dexamethasone, on the other hand, released 40%, 60% and 75% of the dexamethasone in one, three and seven days, respectively. Both types of film maintained low-dose drug release for 28 days. When release behavior was compared between water-insoluble films of different thickness, thicker film showed less initial burst and more sustained release. Dexamethasone release behavior varies according to drug solubility and membrane thickness, and may thus be conrolled

Experimental Study on Ice Forming Process of Cryogenic Liquid Releasing underwater

Science.gov (United States)

Zhang, Bin; Wu, Wanqing; Zhang, Xingdong; Zhang, Yi; Zhang, Chuanlin; Zhang, Haoran; Wang, Peng

2017-11-01

Cryogenic liquid releasing into water would be a process combines hyperactive boiling with ice forming. There are still few researches on the experimental study on the environmental conditions for deciding ice forming speed and liquid surviving state. In this paper, to advance our understanding of ice forming deciding factors in the process of LN2 releasing underwater, a visualization experimental system is built. The results show that the pressure difference significantly influences the ice forming speed and liquid surviving distance, which is observed by the experiment and theoretically analysed by Kelvin-Helmholtz instability. Adding nucleating agent is helpful to provide ice nucleus which can accelerate the ice forming speed. Water flowing has some effect on changing pressure difference, which can affect the ice forming speed and liquid surviving distance.

In vitro effect of Δ9-tetrahydrocannabinol to stimulate somatostatin release and block that of luteinizing hormone-releasing hormone by suppression of the release of prostaglandin E2

International Nuclear Information System (INIS)

Rettori, V.; Aguila, M.C.; McCann, S.M.; Gimeno, M.F.; Franchi, A.M.

1990-01-01

Previous in vivo studies have shown that Δ 9 -tetrahydrocannabinol (THC), the principal active ingredient in marijuana, can suppress both luteinizing hormone (LH) and growth hormone (GH) secretion after its injection into the third ventricle of conscious male rats. The present studies were deigned to determine the mechanism of these effects. Various doses of THC were incubated with either stalk median eminence fragments (MEs) or mediobasal hypothalamic (MBH) fragments in vitro. Although THC (10 nM) did not alter basal release of LH-releasing hormone (LHRH) from MEs in vitro, it completely blocked the stimulatory action of dopamine or nonrepinephrine on LHRH release. The effective doses to block LHRH release were associated with a blockade of synthesis and release of prostaglandin E 2 (PGE 2 ) from MBH in vitro. In contrast to the suppressive effect of THC on LHRH release, somatostatin release from MEs was enhanced in a dose-related manner with a minimal effective dose of 1 nM. Since PGE 2 suppresses somatostatin release, this enhancement may also be related to the suppressive effect of THC on PGE 2 synthesis and release. The authors speculate that these actions are mediated by the recently discovered THC receptors in the tissue. The results indicate that the suppressive effect of THC on LH release is mediated by a blockade of LHRH release, whereas the suppressive effect of the compound on growth hormone release is mediated, at least in part, by a stimulation of somatostatin release

Classification of debris-covered glaciers and rock glaciers in the Andes of central Chile

Science.gov (United States)

Janke, Jason R.; Bellisario, Antonio C.; Ferrando, Francisco A.

2015-07-01

In the Dry Andes of Chile (17 to 35° S), debris-covered glaciers and rock glaciers are differentiated from true glaciers based on the percentage of surface debris cover, thickness of surface debris, and ice content. Internal ice is preserved by an insulating cover of thick debris, which acts as a storage reservoir to release water during the summer and early fall. These landforms are more numerous than glaciers in the central Andes; however, the existing legislation only recognizes uncovered or semicovered glaciers as a water resource. Glaciers, debris-covered glaciers, and rock glaciers are being altered or removed by mining operations to extract valuable minerals from the mountains. In addition, agricultural expansion and population growth in this region have placed additional demands on water resources. In a warmer climate, as glaciers recede and seasonal water availability becomes condensed over the course of a snowmelt season, rock glaciers and debris-covered glaciers contribute a larger component of base flow to rivers and streams. As a result, identifying and locating these features to implement sustainable regional planning for water resources is important. The objective of this study is to develop a classification system to identify debris-covered glaciers and rock glaciers based on the interpretation of satellite imagery and aerial photographs. The classification system is linked to field observations and measurements of ice content. Debris-covered glaciers have three subclasses: surface coverage of semi (class 1) and fully covered (class 2) glaciers differentiates the first two forms, whereas debris thickness is critical for class 3 when glaciers become buried with more than 3 m of surface debris. Based on field observations, the amount of ice decreases from more than 85%, to 65-85%, to 45-65% for semi, fully, and buried debris-covered glaciers, respectively. Rock glaciers are characterized by three stages. Class 4 rock glaciers have pronounced

Mapping Forest Cover and Forest Cover Change with Airborne S-Band Radar

Directory of Open Access Journals (Sweden)

Ramesh K. Ningthoujam

2016-07-01

Full Text Available Assessments of forest cover, forest carbon stocks and carbon emissions from deforestation and degradation are increasingly important components of sustainable resource management, for combating biodiversity loss and in climate mitigation policies. Satellite remote sensing provides the only means for mapping global forest cover regularly. However, forest classification with optical data is limited by its insensitivity to three-dimensional canopy structure and cloud cover obscuring many forest regions. Synthetic Aperture Radar (SAR sensors are increasingly being used to mitigate these problems, mainly in the L-, C- and X-band domains of the electromagnetic spectrum. S-band has not been systematically studied for this purpose. In anticipation of the British built NovaSAR-S satellite mission, this study evaluates the benefits of polarimetric S-band SAR for forest characterisation. The Michigan Microwave Canopy Scattering (MIMICS-I radiative transfer model is utilised to understand the scattering mechanisms in forest canopies at S-band. The MIMICS-I model reveals strong S-band backscatter sensitivity to the forest canopy in comparison to soil characteristics across all polarisations and incidence angles. Airborne S-band SAR imagery over the temperate mixed forest of Savernake Forest in southern England is analysed for its information content. Based on the modelling results, S-band HH- and VV-polarisation radar backscatter and the Radar Forest Degradation Index (RFDI are used in a forest/non-forest Maximum Likelihood classification at a spatial resolution of 6 m (70% overall accuracy, κ = 0.41 and 20 m (63% overall accuracy, κ = 0.27. The conclusion is that S-band SAR such as from NovaSAR-S is likely to be suitable for monitoring forest cover and its changes.

UAS applications in high alpine, snow-covered terrain

Science.gov (United States)

Bühler, Y.; Stoffel, A.; Ginzler, C.

2017-12-01

Access to snow-covered, alpine terrain is often difficult and dangerous. Hence parameters such as snow depth or snow avalanche release and deposition zones are hard to map in situ with adequate spatial and temporal resolution and with spatial continuous coverage. These parameters are currently operationally measured at automated weather stations and by observer networks. However such isolated point measurements are not able to capture the information spatial continuous and to describe the high spatial variability present in complex mountain topography. Unmanned Aerial Systems (UAS) have the potential to fill this gap by frequently covering selected high alpine areas with high spatial resolution down to ground resolutions of even few millimeters. At the WSL Institute for Snow and Avalanche Research SLF we test different photogrammetric UAS with visual and near infrared bands. During the last three years we were able to gather experience in more than 100 flight missions in extreme terrain. By processing the imagery applying state-of-the-art structure from motion (SfM) software, we were able to accurately document several avalanche events and to photogrammetrically map snow depth with accuracies from 1 to 20 cm (dependent on the flight height above ground) compare to manual snow probe measurements. This was even possible on homogenous snow surfaces with very little texture. A key issue in alpine terrain is flight planning. We need to cover regions at high elevations with large altitude differences (up to 1 km) with high wind speeds (up to 20 m/s) and cold temperatures (down to - 25°C). Only a few UAS are able to cope with these environmental conditions. We will give an overview on our applications of UAS in high alpine terrain that demonstrate the big potential of such systems to acquire frequent, accurate and high spatial resolution geodata in high alpine, snow covered terrain that could be essential to answer longstanding questions in avalanche and snow hydrology

Identification and quantification of nitrogen cycling processes in cryptogamic covers

Science.gov (United States)

Weber, Bettina; Wu, Dianming; Lenhart, Katharina; Tamm, Alexandra; Ruckteschler, Nina; Rodríguez-Caballero, Emilio; Elbert, Wolfgang; Burrows, Susannah; Clough, Tim; Steinkamp, Jörg; Meusel, Hannah; Behrendt, Thomas; Büdel, Burkhard; Andreae, Meinrat O.; Sörgel, Matthias; Cheng, Yafang; Crutzen, Paul; Keppler, Frank; Su, Hang; Pöschl, Ulrich

2016-04-01

Cryptogamic covers (CC) comprise communities of photoautotrophic cyanobacteria, lichens, algae, and bryophytes together with heterotrophic bacteria, microfungi, and archaea in varying proportions. Depending on their habitat, cryptogamic rock covers, cryptogamic plant covers, and cryptogamic soil covers are distinguished. The latter comprise biological soil crusts (biocrusts), which globally occur under dryland conditions. In a first assessment of their global role, we quantified that CC fix ˜49 Tg of nitrogen (N) per year (Elbert et al., 2013), corresponding to ˜1/2 of the maximum terrestrial biological N fixation determined in the latest IPCC report. The fixed N is used for biomass formation and partially leached into the ground, where it can be taken up by plants or transformed into N oxides, being emitted into the atmosphere. We show that biocrusts release nitric oxide (NO) and nitrous acid (HONO), which are key species in the global cycling of nitrogen and in the production of ozone and hydroxyl radicals, regulating the oxidizing power and self-cleaning capacity of the atmosphere. Based on laboratory, field and satellite measurement data, we obtained a best estimate of 1.1 Tg a-1 of NO-N and 0.6 Tg a-1 of HONO-N being globally emitted by biocrusts, corresponding to ˜20% of the global nitrogen oxide emissions from soils under natural vegetation (Weber et al., 2015). During full wetting and drying cycles, emissions peaked at low water contents suggesting NO- and HONO-formation under aerobic conditions during nitrification. Other measurements revealed that cryptogamic organisms release nitrous oxide (N2O), a greenhouse gas of crucial importance for climate change. The emission rates varied with temperature, humidity, and N deposition, but divided by respiratory CO2 emission they formed an almost constant ratio, which allowed upscaling on the global scale. We estimated annual N2O emissions of 0.3 - 0.6 Tg by cryptogams, accounting for 4-9% of the global N2O

A multi-objective set covering problem: A case study of warehouse allocation in truck industry

Directory of Open Access Journals (Sweden)

Atefeh Malekinezhad

2011-01-01

Full Text Available Designing distribution centers is normally formulated in a form of set covering where is primary objective is to minimize the number of connected facilities. However, there are other issues affecting our decision on selecting suitable distribution centers such as weather conditions, temperature, infrastructure facilities, etc. In this paper, we propose a multi-objective set covering techniques where different objectives are considered in an integrated model. The proposed model of this paper is implemented for a real-world case study of truck-industry and the results are analyzed.

Fluoride releasing and enamel demineralization around orthodontic brackets by fluoride-releasing composite containing nanoparticles.

Science.gov (United States)

Melo, Mary A S; Morais, Weslanny A; Passos, Vanara F; Lima, Juliana P M; Rodrigues, Lidiany K A

2014-05-01

Fluoride-containing materials have been suggested to control enamel demineralization around orthodontic brackets during the treatment with fixed appliances. The improvement of their properties has been made through innovations, such as the application of nanotechnology by incorporation of nanofillers. This in vitro study evaluated the capacity of fluoride releasing and enamel demineralization inhibition of fluoride-releasing nanofilled cement around orthodontic brackets using an artificial caries biofilm model. Forty bovine enamel discs were selected by evaluating surface microhardness and randomized into four groups (n = 10): non-fluoride-releasing microfilled composite, fluoride-releasing microfilled composite, resin-modified glass ionomer cement (RMGI), and fluoride-releasing nanofilled composite (FN). After brackets bonding in each disc, the specimens were subjected to a cariogenic challenge through a Streptococcus mutans biofilm model. After the experimental period, the biofilm formed around the brackets was collected for fluoride analysis and the mineral loss around the brackets was determined by integrated demineralization via cross-sectional microhardness measurement at 20 and 70 μm from the bracket margin. Additionally, samples of each group were subjected to energy-dispersive X-ray spectroscopy (EDX) analysis examined under a scanning electron microscopy (SEM). ANOVA followed by Tukey test were applied for fluoride concentration and mineral loss data, respectively. At both distances, only RMGI statistically differed from the other groups presenting the lowest demineralization, although there was a trend to a lower demineralization of enamel around brackets in FN group. Similar condition was found to fluoride concentration and EDX/SEM analysis. Under the cariogenic exposure condition of this study, the fluoride-releasing nanofilled material had similar performance to fluoride-releasing microfilled materials. The presence of nanofillers in the fluoride-releasing

Biodegradation study of enzymatically catalyzed interpenetrating polymer network: Evaluation of agrochemical release and impact on soil fertility

Directory of Open Access Journals (Sweden)

Saruchi

2016-03-01

Full Text Available A novel interpenetrating polymer network (IPN has been synthesized through enzymatic initiation using lipase as initiator, glutaraldehyde as cross-linker, acrylic acid as primary monomer and acrylamide as secondary monomer. Biodegradability of synthesized interpenetrating polymer network was studied through soil burial and composting methods. Synthesized hydrogel was completely degraded within 70 days using composting method, while it was 86.03% degraded within 77 days using soil burial method. This was confirmed by Fourier transform Infrared spectroscopy (FTIR and Scanning electron microscopy (SEM techniques. Synthesized interpenetrating polymer network hydrogel was used as a device for controlled release of urea and also act as water releasing device. Their impact on soil fertility and plant growth was also studied. The initial diffusion coefficient has a greater value than the later diffusion coefficient indicating a higher fertilizer release rate during the early stage. Fertilizer release kinetic was also studied which showed Non-Fickian diffusion behavior, as the rate of fertilizer release was comparable to the relaxation time of the synthesized matrix. Synthesized IPN enhance the water uptake capacity up to 6.2% and 7.2% in sandy loam and clay soil, respectively.

Release criteria from hospitals of 131I thyrotoxicosis therapy patients in developing countries - case study

International Nuclear Information System (INIS)

Muhammad, W.; Faaruq, S.; Matiullah; Hussain, A.; Khan, A. A.

2006-01-01

The current release limit, recommended by the International Atomic Energy Agency (IAEA) (1), from hospitals of patients undergoing 131 I thyrotoxicosis therapy is ∼1100 MBq (∼30 mCi). Owing to the difference in socio-economic conditions, literacy rate, family system, etc., this release limit may not be applicable in most of the developing countries like Pakistan. Therefore, the prime objective of this case study was to re-evaluate the release criteria for 131 I thyrotoxicosis therapy patients by taking into account their lifestyle, economic conditions and other facilities such as availability of private/public transport, etc. In this context, systematic studies were carried out and 50 patients (i.e. 35 outpatients and 15 inpatients) at the Nuclear Medicine Oncology and Radiotherapy Inst. (NORI), Islamabad, were studied. Exposure rate at the surface of the body and at a distance of 1 m from the standing patient was measured. Results obtained from this study showed that the dose equivalent delivered by these patients to their family members (particularly children) and general public was higher than annual dose limits recommended by the International Commission for Radiation Protection in their report ICRP Publication 60 (2). In the light of this study, it is recommended that the release activity limit of ∼370 MBq (or dose rate level of ∼10 μSv h -1 at 1 m from the patient) be adopted instead of ∼1100 MBq in developing countries like Pakistan. (authors)

A Comparative Study of Land Cover Classification by Using Multispectral and Texture Data

Directory of Open Access Journals (Sweden)

Salman Qadri

2016-01-01

Full Text Available The main objective of this study is to find out the importance of machine vision approach for the classification of five types of land cover data such as bare land, desert rangeland, green pasture, fertile cultivated land, and Sutlej river land. A novel spectra-statistical framework is designed to classify the subjective land cover data types accurately. Multispectral data of these land covers were acquired by using a handheld device named multispectral radiometer in the form of five spectral bands (blue, green, red, near infrared, and shortwave infrared while texture data were acquired with a digital camera by the transformation of acquired images into 229 texture features for each image. The most discriminant 30 features of each image were obtained by integrating the three statistical features selection techniques such as Fisher, Probability of Error plus Average Correlation, and Mutual Information (F + PA + MI. Selected texture data clustering was verified by nonlinear discriminant analysis while linear discriminant analysis approach was applied for multispectral data. For classification, the texture and multispectral data were deployed to artificial neural network (ANN: n-class. By implementing a cross validation method (80-20, we received an accuracy of 91.332% for texture data and 96.40% for multispectral data, respectively.

Study on radioactive release of gaseous and liquid effluents during normal operation of AP1000

International Nuclear Information System (INIS)

Gong Quan; Zhou Jing; Liu Yu

2014-01-01

The gaseous and liquid radioactive releases of pressurized water reactors plant during normal operation are an important content of environmental impact assessment and play a significant role in the design of nuclear power plant. According to the design characters of AP1OOO radioactive waste management system and the study on the calculation method and the release pathways, the calculation model of the gaseous and liquid radioactive releases during normal operation for AP1OOO are established. Base on the established calculation model and the design parameters of AP1000, the expected value of gaseous and liquid radioactive releases of AP1OOO is calculated. The results of calculation are compared with the limits in GB 6249-2011 and explain the adder that is included tu account for anticipated operational occurrences, providing a reference for environmental impact assessment of pressurized water reactor. (authors)

Controlled release and intracellular protein delivery from mesoporous silica nanoparticles.

Science.gov (United States)

Deodhar, Gauri V; Adams, Marisa L; Trewyn, Brian G

2017-01-01

Protein therapeutics are promising candidates for disease treatment due to their high specificity and minimal adverse side effects; however, targeted protein delivery to specific sites has proven challenging. Mesoporous silica nanoparticles (MSN) have demonstrated to be ideal candidates for this application, given their high loading capacity, biocompatibility, and ability to protect host molecules from degradation. These materials exhibit tunable pore sizes, shapes and volumes, and surfaces which can be easily functionalized. This serves to control the movement of molecules in and out of the pores, thus entrapping guest molecules until a specific stimulus triggers release. In this review, we will cover the benefits of using MSN as protein therapeutic carriers, demonstrating that there is great diversity in the ways MSN can be used to service proteins. Methods for controlling the physical dimensions of pores via synthetic conditions, applications of therapeutic protein loaded MSN materials in cancer therapies, delivering protein loaded MSN materials to plant cells using biolistic methods, and common stimuli-responsive functionalities will be discussed. New and exciting strategies for controlled release and manipulation of proteins are also covered in this review. While research in this area has advanced substantially, we conclude this review with future challenges to be tackled by the scientific community. Copyright © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Environmental contamination from a ground-level release of fission products

International Nuclear Information System (INIS)

Stupka, R.C.; Kephart, G.S.; Rittmann, P.D.

1986-08-01

On January 11, 1985, a ground-level release of fission products, primarily 90 Sr, occurred at the Hanford Site in southeastern Washington State. The release was detected during routine surveys and the majority of the contamination was confined to the immediate area where the release occurred. Response to the incident was complicated by a strong inversion that resulted in a buildup of 222 Rn daughter products on environmental air samples and outdoor surfaces. The cause of the release appears to have been the operation of a transfer jet that inadvertently pressurized an unblanked line leading to the 241-C-151 Diversion Box. A buildup of pressure inside the diversion box forced contaminated air through gaps in the diversion box cover blocks resulting in an unmonitored, short duration release to the environment. The source term was estimated using data obtained from environmental air samplers. The ground deposition speed was calculated using the integrated exposure (air samples) and surface contamination levels obtained from recently fallen snow. The total release was estimated to be 1.4 Ci 90 Sr and 0.02 Ci 137 Cs. Based on this source term, the maximum 50-yr dose commitment to onsite pesonnel was 50 mrem whole body and 600 mrem bone. No detectable internal deposition occurred during the incident and corrective action which followed; this was probably due to several factors: (1) prompt detection of the release; (2) localized contamination control; (3) excellent personnel protection practices; and (4) the protection offered by building ventilation systems. The theoretical maximum offsite individual would receive a potential 1-yr dose commitment of 0.01 mrem whole body and 0.2 mrem bone from this incident. The potential 50-yr dose commitment would be 0.13 mrem whole body and 2.0 mrem bone. In actuality, neither onsite or offsite individuals would be expected to receive even these small dose commitments

Decomposição e liberação de nitrogênio de resíduos culturais de plantas de cobertura em um solo de cerrado Cover crops residue decomposition and nitrogen release in a cerrado soil

Directory of Open Access Journals (Sweden)

José Luiz Rodrigues Torres

2005-07-01

Full Text Available A produção de massa seca, a taxa de decomposição e a liberação de nitrogênio (N foram avaliadas em um experimento com sete tipos de cobertura vegetal: milheto pérola (Pennisetum americanum sin. tiphoydes, braquiária (Brachiaria brizantha, sorgo forrageiro (Sorghum bicolor L. Moench, guandu (Cajanus cajan (L. Millsp, crotalária juncea (Crotalarea juncea e aveia-preta (Avena strigosa Schreb, em pousio e em área de cultivo convencional (testemunha, em solo de cerrado, em Uberaba, região do Triângulo Mineiro. Dentre as coberturas avaliadas, o milheto e a crotalária foram as que apresentaram a maior produção de massa seca, maior acúmulo e a maior liberação de N. A braquiária foi a cobertura que apresentou a maior taxa de decomposição. Todas as coberturas apresentaram a maior taxa de liberação de N até 42 dias após dessecação.Dry mass production, decomposition rate and nitrogen (N release were evaluated in a field experiment under seven cover crop types: pearl millet (Pennisetum americanum sin. typhoides, brachiaria grass (Brachiaria brizantha, sorghum (Sorghum bicolor L. Moench, pigeon pea (Cajanus cajan (L. Mill sp, sunn hemp (Crotalaria juncea and black oat (Avena strigosa Schreb, compared to a fallow and a traditional cropping system (control in a cerrado soil (Uberaba-MG, Brazil. Among the tested cover crops, pearl millet and sunn hemp presented higher dry mass yield and nitrogen accumulation and release. Brachiaria grass had the highest decomposition rate and shortest half-life time. All crops reached the highest N liberation rate 42 days after desiccation.

Using ASTER Imagery in Land Use/cover Classification of Eastern Mediterranean Landscapes According to CORINE Land Cover Project

Directory of Open Access Journals (Sweden)

Recep Gundogan

2008-02-01

Full Text Available The satellite imagery has been effectively utilized for classifying land covertypes and detecting land cover conditions. The Advanced Spaceborne Thermal Emissionand Reflection Radiometer (ASTER sensor imagery has been widely used in classificationprocess of land cover. However, atmospheric corrections have to be made by preprocessingsatellite sensor imagery since the electromagnetic radiation signals received by the satellitesensors can be scattered and absorbed by the atmospheric gases and aerosols. In this study,an ASTER sensor imagery, which was converted into top-of-atmosphere reflectance(TOA, was used to classify the land use/cover types, according to COoRdination ofINformation on the Environment (CORINE land cover nomenclature, for an arearepresenting the heterogonous characteristics of eastern Mediterranean regions inKahramanmaras, Turkey. The results indicated that using the surface reflectance data ofASTER sensor imagery can provide accurate (i.e. overall accuracy and kappa values of83.2% and 0.79, respectively and low-cost cover mapping as a part of inventory forCORINE Land Cover Project.

Gas release during salt-well pumping: Model predictions and laboratory validation studies for soluble and insoluble gases

International Nuclear Information System (INIS)

Peurrung, L.M.; Caley, S.M.; Gauglitz, P.A.

1997-08-01

The Hanford Site has 149 single-shell tanks (SSTs) containing radioactive wastes that are complex mixes of radioactive and chemical products. Of these, 67 are known or suspected to have leaked liquid from the tanks into the surrounding soil. Salt-well pumping, or interim stabilization, is a well-established operation for removing drainable interstitial liquid from SSTs. The overall objective of this ongoing study is to develop a quantitative understanding of the release rates and cumulative releases of flammable gases from SSTs as a result of salt-well pumping. The current study is an extension of the previous work reported by Peurrung et al. (1996). The first objective of this current study was to conduct laboratory experiments to quantify the release of soluble and insoluble gases. The second was to determine experimentally the role of characteristic waste heterogeneities on the gas release rates. The third objective was to evaluate and validate the computer model STOMP (Subsurface Transport over Multiple Phases) used by Peurrung et al. (1996) to predict the release of both soluble (typically ammonia) and insoluble gases (typically hydrogen) during and after salt-well pumping. The fourth and final objective of the current study was to predict the gas release behavior for a range of typical tank conditions and actual tank geometry. In these models, the authors seek to include all the pertinent salt-well pumping operational parameters and a realistic range of physical properties of the SST wastes. For predicting actual tank behavior, two-dimensional (2-D) simulations were performed with a representative 2-D tank geometry

Moisture content analysis of covered uranium mill tailings

International Nuclear Information System (INIS)

Mayer, D.W.; Beedlow, P.A.; Cadwell, L.L.

1981-12-01

The use of vegetation and rock covers to stabilize uranium mill tailings cover systems is being investigated by Pacific Northwest Laboratory. A modeling study of moisture movement through the tailings and cover layers was initiated to determine the effect of the stabilizing techniques. The cover system was simulated under climatic conditions occurring at Grand Junction, Colorado. The cover consisted of a layer of wet clay/gravel mix followed by a capillary barrier of washed rock and a surface layer of fill soil. Vegetation and rock were used to stabilize the surface layer. The simulation yielded moisture content and moisture storage values for the tailings and cover system along with information about moisture losses due to evaporation, transpiration, and drainage. The study demonstrates that different surface stabilization treatments lead to different degrees of moisture retention in the covered tailings pile. The evapotranspiration from vegetation can result in a relatively stable moisture content. Rock covers, however, may cause drainage to occur because they reduce evaporation and lead to a subsequent increase in moisture content. It is important to consider these effects when designing a surface stabilization treatment. Drainage may contribute to a groundwater pollution problem. A surface treatment that allows the cover system to dry out can increase the risk of atmospheric contamination through elevated radon emission rates

Non-commutative covering spaces and their symmetries

DEFF Research Database (Denmark)

Canlubo, Clarisson

dened and its corresponding Galois theory. Using this and basic concepts from algebraic geometryand spectral theory, we will give a full description of the general structure of non-centralcoverings. Examples of coverings of the rational and irrational non-commutative tori will alsobe studied. Using...... will explain this and relate it to bi-Galois theory.Using the OZ-transform, we will show that non-commutative covering spaces come in pairs.Several categories of covering spaces will be dened and studied. Appealing to Tannaka duality,we will explain how this lead to a notion of an etale fundamental group...

Cost-effectiveness of extended-release methylphenidate in children and adolescents with attention-deficit/hyperactivity disorder sub-optimally treated with immediate release methylphenidate.

Directory of Open Access Journals (Sweden)

Jurjen van der Schans

Full Text Available Attention-Deficit/Hyperactivity Disorder (ADHD is a common psychiatric disorder in children and adolescents. Immediate-release methylphenidate (IR-MPH is the medical treatment of first choice. The necessity to use several IR-MPH tablets per day and associated potential social stigma at school often leads to reduced compliance, sub-optimal treatment, and therefore economic loss. Replacement of IR-MPH with a single-dose extended release (ER-MPH formulation may improve drug response and economic efficiency.To evaluate the cost-effectiveness from a societal perspective of a switch from IR-MPH to ER-MPH in patients who are sub-optimally treated.A daily Markov-cycle model covering a time-span of 10 years was developed including four different health states: (1 optimal response, (2 sub-optimal response, (3 discontinued treatment, and (4 natural remission. ER-MPH options included methylphenidate osmotic release oral system (MPH-OROS and Equasym XL/Medikinet CR. Both direct costs and indirect costs were included in the analysis, and effects were expressed as quality-adjusted life years (QALYs. Univariate, multivariate as well as probabilistic sensitivity analysis were conducted and the main outcomes were incremental cost-effectiveness ratios.Switching sub-optimally treated patients from IR-MPH to MPH-OROS or Equasym XL/Medikinet CR led to per-patient cost-savings of €4200 and €5400, respectively, over a 10-year treatment span. Sensitivity analysis with plausible variations of input parameters resulted in cost-savings in the vast majority of estimations.This study lends economic support to switching patients with ADHD with suboptimal response to short-acting IR-MPH to long-acting ER-MPH regimens.

Segmentation schema for enhancing land cover identification: A case study using Sentinel 2 data

Science.gov (United States)

Mongus, Domen; Žalik, Borut

2018-04-01

Land monitoring is performed increasingly using high and medium resolution optical satellites, such as the Sentinel-2. However, optical data is inevitably subjected to the variable operational conditions under which it was acquired. Overlapping of features caused by shadows, soft transitions between shadowed and non-shadowed regions, and temporal variability of the observed land-cover types require radiometric corrections. This study examines a new approach to enhancing the accuracy of land cover identification that resolves this problem. The proposed method constructs an ensemble-type classification model with weak classifiers tuned to the particular operational conditions under which the data was acquired. Iterative segmentation over the learning set is applied for this purpose, where feature space is partitioned according to the likelihood of misclassifications introduced by the classification model. As these are a consequence of overlapping features, such partitioning avoids the need for radiometric corrections of the data, and divides land cover types implicitly into subclasses. As a result, improved performance of all tested classification approaches were measured during the validation that was conducted on Sentinel-2 data. The highest accuracies in terms of F1-scores were achieved using the Naive Bayes Classifier as the weak classifier, while supplementing original spectral signatures with normalised difference vegetation index and texture analysis features, namely, average intensity, contrast, homogeneity, and dissimilarity. In total, an F1-score of nearly 95% was achieved in this way, with F1-scores of each particular land cover type reaching above 90%.

Influence of snow cover distribution on soil temperature and nutrient dynamics in alpine pedoenvironments

Directory of Open Access Journals (Sweden)

Ermanno Zanini

Full Text Available In Alpine sites snow is present on the ground from six to eight months per year in relation to elevation and exposure. Water is therefore immobilized into the solid state for the greater part of the winter season and released to the ground in a short period during spring snowmelt. In these areas, snow distribution exercises a fundamental role in influencing soil temperature and nutrient dynamics, in particular of nitrogen, with great consequences on plant nutrition. The dormant vegetation period, the low temperatures and the persistent snow cover suggest that soil biological activity is only concentrated during summer. As a matter of fact, soils covered with a consistent snow cover are isolated from the air temperature and can not freeze during winter. A snowpack of sufficient thickness, accumulated early in winter, insulates the ground from the surrounding atmosphere maintaining soil temperature closed to 0 °C during the whole winter season. The elevation of the snow line and the shorter permanence of snow on the ground, as a result of global warming (IPCC, 1996, 2001, might reduce the insulation effect of the snowpack, exposing soils of the mountain belt to lower temperatures and to a greater frequency of freeze/thaw cycles, which might alter organic matter dynamics and soil nutrient availability. Such thermal stresses may determine the lysis of microbial cells and the consequent increase of nitrogen and carbon mineralization by the survived microorganisms. Moreover, the freeze/thaw cycles can determine the exposure of exchange surfaces not available before, with release of organic matter of non-microbial origin, which may become available to surviving microorganisms for respiration. The reduced or absent microbial immobilization may cause the accumulation of remarkable amounts of inorganic nitrogen in soil, potentially leachable during spring snowmelt, when plants have not still started the growing season. Changes of snow distribution in

The influence of multi-season imagery on models of canopy cover: A case study

Science.gov (United States)

John W. Coulston; Dennis M. Jacobs; Chris R. King; Ivey C. Elmore

2013-01-01

Quantifying tree canopy cover in a spatially explicit fashion is important for broad-scale monitoring of ecosystems and for management of natural resources. Researchers have developed empirical models of tree canopy cover to produce geospatial products. For subpixel models, percent tree canopy cover estimates (derived from fine-scale imagery) serve as the response...

Histamine is not released in acute thermal injury in human skin in vivo: a microdialysis study

DEFF Research Database (Denmark)

Petersen, Lars Jelstrup; Pedersen, Juri Lindy; Skov, Per Stahl

2009-01-01

BACKGROUND: Animal models have shown histamine to be released from the skin during the acute phase of a burn injury. The role of histamine during the early phase of thermal injuries in humans remains unclear. PURPOSE: The objectives of this trial were to study histamine release in human skin during...

Studies related to the development of the viking 1975 labeled release experiment

International Nuclear Information System (INIS)

Devincenzi, D.L.; Deal, P.H.

1976-04-01

The labeled release life detection experiment on the Viking 1975 Mars mission is based on the concept that microorganisms will metabolize radioactive organic substrates in a nutrient medium and release radioactive carbon dioxide. Several experiments, using laboratory equipment, were carried out to evaluate various aspects of the concept. Results indicate: (1) label is released by sterilization-treated soil, (2) substantial quantities of label are retained in solution under basic conditions, (3) the substrate used, as well as position of label in the molecule, affect release of label, (4) label release is depressed by radiolytic decomposition of substrates, and (5) About 100,000 organisms are required to produce a detectable response. These results, suggest additional areas for testing, add to the data base for interpretation of flight results, and have significance for broader application of this technique for assessing microbial activity. (Author)

Final Report for the DOE-BES Program Mechanistic Studies of Activated Hydrogen Release from Amine-Boranes

Energy Technology Data Exchange (ETDEWEB)

Larry G. Sneddon; R. Thomas Baker

2013-01-13

Effective storage of hydrogen presents one of the most significant technical gaps to successful implementation of the hydrogen economy, particularly for transportation applications. Amine boranes, such as ammonia borane H3NBH3 and ammonia triborane H3NB3H7, have been identified as promising, high-capacity chemical hydrogen storage media containing potentially readily released protic (N-H) and hydridic (B-H) hydrogens. At the outset of our studies, dehydrogenation of ammonia borane had been studied primarily in the solid state, but our DOE sponsored work clearly demonstrated that ionic liquids, base-initiators and/or metal-catalysts can each significantly increase both the rate and extent of hydrogen release from amine boranes under moderate conditions. Our studies also showed that depending upon the activation method, hydrogen release from amine boranes can occur by very different mechanistic steps and yield different types of spent-fuel materials. The fundamental understanding that was developed during this grant of the pathways and controlling factors for each of these hydrogen-release mechanisms is now enabling continuing discovery and optimization of new chemical-hydride based hydrogen storage systems.

Controlled release of volatiles under mild reaction conditions: from nature to everyday products.

Science.gov (United States)

Herrmann, Andreas

2007-01-01

Volatile organic compounds serve in nature as semiochemicals for communication between species, and are often used as flavors and fragrances in our everyday life. The quite limited longevity of olfactive perception has led to the development of pro-perfumes or pro-fragrances--ideally nonvolatile and odorless fragrance precursors which release the active volatiles by bond cleavage. Only a limited amount of reaction conditions, such as hydrolysis, temperature changes, as well as the action of light, oxygen, enzymes, or microorganisms, can be used to liberate the many different chemical functionalities. This Review describes the controlled chemical release of fragrances and discusses additional challenges such as precursor stability during product storage as well as some aspects concerning toxicity and biodegradability. As the same systems can be applied in different areas of research, the scope of this Review covers fragrance delivery as well as the controlled release of volatiles in general.

An experimental study of the trapping and release of krypton in nickel

International Nuclear Information System (INIS)

Donnelly, S.E.; Ingram, D.C.; Armour, D.G.

1979-01-01

An experimental study is reported of the trapping and release of krypton implanted into nickel at low energies ( + incident on Ni (110) the maximum quantity of gas retained in the target was found to be approximately 2.5 x 10 15 ions cm -2 . (author)

ATP Release and Effects in Pancreas

DEFF Research Database (Denmark)

Novak, Ivana; Amstrup, Jan; Henriksen, Katrine Lütken

2003-01-01

ATP and other nucleotides are released from various cells, but the pathway and physiological stimulus for ATP release are often unclear. The focus of our studies is the understanding of ATP release and signaling in rat exocrine pancreas. In acinar suspension mechanical stimulation, hypotonic shock...

Gliclazide directly inhibits arginine-induced glucagon release

DEFF Research Database (Denmark)

Cejvan, Kenan; Coy, David H; Holst, Jens Juul

2002-01-01

Arginine-stimulated insulin and somatostatin release is enhanced by the sulfonylurea gliclazide. In contrast, gliclazide inhibits the glucagon response. The aim of the present study was to investigate whether this inhibition of glucagon release was mediated by a direct suppressive effect of glicl......Arginine-stimulated insulin and somatostatin release is enhanced by the sulfonylurea gliclazide. In contrast, gliclazide inhibits the glucagon response. The aim of the present study was to investigate whether this inhibition of glucagon release was mediated by a direct suppressive effect....... In islet perifusions with DC-41-33, arginine-induced glucagon release was inhibited by 66%. We therefore concluded that gliclazide inhibits glucagon release by a direct action on the pancreatic A cell....

The role of protected areas in land use/land cover change and the carbon cycle in the conterminous United States

Energy Technology Data Exchange (ETDEWEB)

Lu, Xiaoliang [The Ecosystems Center, Marine Biological Laboratory, Woods Hole MA USA; Zhou, Yuyu [Departments of Geological and Atmospheric Sciences, Iowa State University, Ames IA USA; Liu, Yaling [Pacific Northwest National Laboratory, Joint Global Change Research Institute, College Park MD USA; Le Page, Yannick [Department Tapada da Ajuda, Centro de Estudos Florestais, Instituto Superior de Agronomia, Universidade de Lisboa, Lisbon Portugal

2017-08-08

Protected areas (PAs) cover about 22% of the conterminous United States. Understanding their role on historical land use and land cover change (LULCC) and on the carbon cycle is essential to provide guidance for environmental policies. In this study, we compiled historical LULCC and PAs data to explore these interactions within the terrestrial ecosystem model (TEM). We found that intensive LULCC occurred in the conterminous United States from 1700 to 2005. More than 3 million km2 of forest, grassland and shrublands were converted into agricultural lands, which caused 10,607 Tg C release from land ecosystems to atmosphere. PAs had experienced little LULCC as they were generally established in the 20th century after most of the agricultural expansion had occurred. PAs initially acted as a carbon source due to land use legacies, but their accumulated carbon budget switched to a carbon sink in the 1960s, sequestering an estimated 1,642 Tg C over 1700–2005, or 13.4% of carbon losses in non-PAs. We also find that PAs maintain larger carbon stocks and continue sequestering carbon in recent years (2001–2005), but at a lower rate due to increased heterotrophic respiration as well as lower productivity associated to aging ecosystems. It is essential to continue efforts to maintain resilient, biodiverse ecosystems and avoid large-scale disturbances that would release large amounts of carbon in PAs.

Release-ability of nano fillers from different nanomaterials (toward the acceptability of nanoproduct)

International Nuclear Information System (INIS)

Golanski, L.; Guiot, A.; Pras, M.; Malarde, M.; Tardif, F.

2012-01-01

It is of great interest to set up a reproducible and sensitive method able to qualify nanomaterials before their market introduction in terms of their constitutive nanoparticle release-ability in usage. Abrasion was performed on polycarbonate, epoxy, and PA11 polymers containing carbone nanotubes (CNT) up to 4 %wt. Using Taber linear standard tool and standard abrasion conditions no release from polymer coatings containing CNT was measured. In this study, new practical tools inducing non-standardized stresses able to compete with van der Waals forces were developed and tested on model polymers, showing controlled CNT dispersion. These stresses are still realistic, corresponding to scratching, instantaneous mechanical shocks, and abrasion of the surface. They offer an efficient way to quantify if release is possible from nanomaterials under different mechanical stresses and therefore give an idea about the mechanisms that favors it. Release under mechanical shocks and hard abrasion was obtained using these tools but only when nanomaterials present a bad dispersion of CNT within the epoxy matrix. Under the same conditions no release was obtained from the same material presenting a good dispersion. The CNT used in this study showed an external diameter Dext = 12 nm, an internal diameter Din = 5 nm, and a mean length of 1 μm. Release from paints under hard abrasion using a standard rotative Taber tool was obtained from a intentionaly non-optimized paint containing SiO 2 nanoparticles up to 35 %wt. The primary diameter of the SiO 2 was estimated to be around 12 nm. A metallic rake was efficient to remove nanoparticles from a non-woven fabric nanomaterial.

The Release of Trace Elements in the Process of Coal Coking

Directory of Open Access Journals (Sweden)

Jan Konieczyński

2012-01-01

Full Text Available In order to assess the penetration of individual trace elements into the air through their release in the coal coking process, it is necessary to determine the loss of these elements by comparing their contents in the charge coal and in coke obtained. The present research covered four coke oven batteries differing in age, technology, and technical equipment. By using mercury analyzer MA-2 and the method of ICP MS As, Be, Cd, Co, Hg, Mn, Ni, Se, Sr, Tl, V, and Zn were determined in samples of charge coal and yielded coke. Basing on the analyses results, the release coefficients of selected elements were determined. Their values ranged from 0.5 to 94%. High volatility of cadmium, mercury, and thallium was confirmed. The tests have shown that although the results refer to the selected case studies, it may be concluded that the air purity is affected by controlled emission occurring when coke oven batteries are fired by crude coke oven gas. Fugitive emission of the trace elements investigated, occurring due to coke oven leaks and openings, is small and, is not a real threat to the environment except mercury.

The application of thermoluminescence dosimeters to studies of released activity distributions

International Nuclear Information System (INIS)

Ruden, B.I.

1969-06-01

In this report the theoretical conditions necessary for the study of the behaviour of released activity by the use of CaSO 4 : Mn thermoluminescence dosimeters are considered. A method is derived for calculating exposure distributions from drifting volume activity. The correlation between exposure distributions and concentration distributions is discussed. One of thirty experiments where Br 82 was released into water through a nozzle some metres above the bottom is described. The resulting exposure distribution was measured in a vertical plane at distances of 10, 50 and 200 metres by CaSO 4 : Mn thermoluminescence dosimeters. The measured exposures are described and discussed. The advantages and disadvantages of the technique are compared with other methods. The method using exposure measurements for the study of active release in water has given satisfactory results in practice. The measurements have been made at concentration levels which are considerably below that permissible for drinking water according to the recommendations by ICRPA special advantage with this method is that the measurements can be made simultaneously at a large number of places and that integration is possible over sufficiently long periods of time. An experiment is described where Ar 41 was released in free air at a height of one metre above ground and the resulting exposure distribution was measured in a vertical plane at 100 and 250 metres distance by CaSO 4 : Mn thermoluminescence dosimeters. Shielding problems in connection with the experiments have been small since the method permits the measurement of very small doses. An account is given of the possibility of using the beta emitting isotope Kr 85 instead of the gamma emitting Ar 41 for diffusion experiments in air. The results obtained from some experiments are presented and discussed. The thermoluminescent signal from the dosimeters are, at the same concentration and exposure time, 2.5 times greater for Kr 85 than for Ar 41. The Kr

Sleep-wake sensitive mechanisms of adenosine release in the basal forebrain of rodents: an in vitro study.

Directory of Open Access Journals (Sweden)

Robert Edward Sims

Full Text Available Adenosine acting in the basal forebrain is a key mediator of sleep homeostasis. Extracellular adenosine concentrations increase during wakefulness, especially during prolonged wakefulness and lead to increased sleep pressure and subsequent rebound sleep. The release of endogenous adenosine during the sleep-wake cycle has mainly been studied in vivo with microdialysis techniques. The biochemical changes that accompany sleep-wake status may be preserved in vitro. We have therefore used adenosine-sensitive biosensors in slices of the basal forebrain (BFB to study both depolarization-evoked adenosine release and the steady state adenosine tone in rats, mice and hamsters. Adenosine release was evoked by high K(+, AMPA, NMDA and mGlu receptor agonists, but not by other transmitters associated with wakefulness such as orexin, histamine or neurotensin. Evoked and basal adenosine release in the BFB in vitro exhibited three key features: the magnitude of each varied systematically with the diurnal time at which the animal was sacrificed; sleep deprivation prior to sacrifice greatly increased both evoked adenosine release and the basal tone; and the enhancement of evoked adenosine release and basal tone resulting from sleep deprivation was reversed by the inducible nitric oxide synthase (iNOS inhibitor, 1400 W. These data indicate that characteristics of adenosine release recorded in the BFB in vitro reflect those that have been linked in vivo to the homeostatic control of sleep. Our results provide methodologically independent support for a key role for induction of iNOS as a trigger for enhanced adenosine release following sleep deprivation and suggest that this induction may constitute a biochemical memory of this state.

Sustained-release microsphere formulation containing an agrochemical by polyurethane polymerization during an agitation granulation process.

Science.gov (United States)

Terada, Takatoshi; Tagami, Manabu; Ohtsubo, Toshiro; Iwao, Yasunori; Noguchi, Shuji; Itai, Shigeru

2016-07-25

In this report, a new solventless microencapsulation method by synthesizing polyurethane (PU) from polyol and isocyanate during an agglomeration process in a high-speed mixing apparatus was developed. Clothianidin (CTD), which is a neonicotinoid insecticide and highly effective against a wide variety of insect pests, was used as the model compound. The microencapsulated samples covered with PU (CTD microspheres) had a median diameter of <75μm and sustained-release properties. The CTD microspheres were analyzed by synchrotron X-ray computed tomography measurements. Multiple cores of CTD and other solid excipient were dispersed in PU. Although voids appeared in the CTD microspheres after CTD release, the spherical shape of the microspheres remained stable and no change in its framework was observed. The experimental release data were highly consistent with the Baker-Lonsdale model derived from drug release of spherical monolithic dispersions and consistent with the computed tomography measurements. Copyright © 2016 Elsevier B.V. All rights reserved.

THE RAVE CATALOG OF STELLAR ELEMENTAL ABUNDANCES: FIRST DATA RELEASE

Energy Technology Data Exchange (ETDEWEB)

Boeche, C.; Williams, M.; De Jong, R. S.; Steinmetz, M. [Leibniz-Institut fuer Astrophysik Potsdam (AIP), D-14482 Potsdam (Germany); Siebert, A.; Bienayme, O. [Observatoire Astronomique de Strasbourg, Universite de Strasbourg, CNRS, UMR 7550, F-67000 Strasbourg (France); Fulbright, J. P.; Ruchti, G. R. [Department of Physics and Astronomy, Johns Hopkins University, Baltimore, MD 21218 (United States); Bland-Hawthorn, J. [Sydney Institute for Astronomy, School of Physics A28, University of Sydney, NSW 2006 (Australia); Campbell, R. [Department of Physics and Astronomy, Western Kentucky University, Bowling Green, KY (United States); Freeman, K. C. [Research School of Astronomy and Astrophysics, Australia National University, Weston Creek, Canberra ACT 2611 (Australia); Gibson, B. K. [Jeremiah Horrocks Institute, University of Central Lancashire, Preston PR1 2HE (United Kingdom); Gilmore, G. [Institute of Astronomy, University of Cambridge, Madingley Road, Cambridge CB3 0HA (United Kingdom); Grebel, E. K. [Astronomisches Rechen-Institut, Zentrum fuer Astronomie der Universitaet Heidelberg, D-69120 Heidelberg (Germany); Helmi, A. [Kapteyn Astronomical Institute, University of Groningen, 9700 AV Groningen (Netherlands); Munari, U. [INAF Osservatorio Astronomico di Padova, Asiago I-36012 (Italy); Navarro, J. F. [Department of Physics and Astronomy, University of Victoria, Victoria BC V8W 3P6 (Canada); Parker, Q. A.; Reid, W. [Department of Physics and Astronomy, Faculty of Sciences, Macquarie University, Sydney, NSW 2109 (Australia); Seabroke, G. M. [Mullard Space Science Laboratory, University College London, Holmbury, St. Mary RH5 6NT (United Kingdom); and others

2011-12-15

We present chemical elemental abundances for 36,561 stars observed by the RAdial Velocity Experiment (RAVE), an ambitious spectroscopic survey of our Galaxy at Galactic latitudes |b| > 25 Degree-Sign and with magnitudes in the range 9 cover the Ca-triplet region at 8410-8795 A with resolving power R {approx} 7500. This first data release of the RAVE chemical catalog is complementary to the third RAVE data release of radial velocities and stellar parameters, and it contains chemical abundances for the elements Mg, Al, Si, Ca, Ti, Fe, and Ni, with a mean error of {approx}0.2 dex, as judged from accuracy tests performed on synthetic and real spectra. Abundances are estimated through a dedicated processing pipeline in which the curve of growth of individual lines is obtained from a library of absorption line equivalent widths to construct a model spectrum that is then matched to the observed spectrum via a {chi}{sup 2} minimization technique. We plan to extend this pipeline to include estimates for other elements, such as oxygen and sulfur, in future data releases.

Studies of two naturally occurring compounds which effect release of acetylcholine from synaptosomes

International Nuclear Information System (INIS)

Koenig, M.L.

1985-01-01

Two naturally occurring compounds which effect the release of neurotransmitter from synaptosomes have been purified to apparent homogeneity. Iotrochotin (IOT) isolated from wound exudate of the Caribbean purple bleeder sponge promotes release in a manner that is independent of the extracellular Ca 2+ ion concentration. Leptinotarsin (LPT-d), a protein taken from hemolymph of the Colorado potato beetle, Leptinotarsa decemlineata, stimulates Ca 2+ -dependent release. IOT is slightly acidic and has a molecular weight of approximately 18 kD. [ 3 H]acetylcholine which has been introduced into synaptosomes as [ 3 H]choline can be released by IOT. The toxin releasable pool of labelled neurotransmitter is not depleted by depolarization of the synaptosomes with high potassium, and therefore seems to be primarily extravesicular. LPT-d is a larger protein (molecular weight = 45 kD) than IOT, and seems to effect primarily vesicular release by opening at least one type of presynaptic Ca 2+ channel. The facilitatory effects of the toxin on synaptosomal release can be inhibited by inorganic Ca 2+ channel antagonists, but are not generally affected by organic antagonists

Minimum forest cover required for sustainable water flow regulation of a watershed: a case study in Jambi Province, Indonesia

Science.gov (United States)

Tarigan, Suria; Wiegand, Kerstin; Sunarti; Slamet, Bejo

2018-01-01

In many tropical regions, the rapid expansion of monoculture plantations has led to a sharp decline in forest cover, potentially degrading the ability of watersheds to regulate water flow. Therefore, regional planners need to determine the minimum proportion of forest cover that is required to support adequate ecosystem services in these watersheds. However, to date, there has been little research on this issue, particularly in tropical areas where monoculture plantations are expanding at an alarming rate. Therefore, in this study, we investigated the influence of forest cover and oil palm (Elaeis guineensis) and rubber (Hevea brasiliensis) plantations on the partitioning of rainfall into direct runoff and subsurface flow in a humid, tropical watershed in Jambi Province, Indonesia. To do this, we simulated streamflow with a calibrated Soil and Water Assessment Tool (SWAT) model and observed several watersheds to derive the direct runoff coefficient (C) and baseflow index (BFI). The model had a strong performance, with Nash-Sutcliffe efficiency values of 0.80-0.88 (calibration) and 0.80-0.85 (validation) and percent bias values of -2.9-1.2 (calibration) and 7.0-11.9 (validation). We found that the percentage of forest cover in a watershed was significantly negatively correlated with C and significantly positively correlated with BFI, whereas the rubber and oil palm plantation cover showed the opposite pattern. Our findings also suggested that at least 30 % of the forest cover was required in the study area for sustainable ecosystem services. This study provides new adjusted crop parameter values for monoculture plantations, particularly those that control surface runoff and baseflow processes, and it also describes the quantitative association between forest cover and flow indicators in a watershed, which will help regional planners in determining the minimum proportion of forest and the maximum proportion of plantation to ensure that a watershed can provide

Emergency department use by released prisoners with HIV: an observational longitudinal study.

Directory of Open Access Journals (Sweden)

Jaimie P Meyer

Full Text Available Many people living with HIV access healthcare systems through the emergency department (ED, and increased ED use may be indicative of disenfranchisement with primary HIV care, under-managed comorbid disease, or coincide with use of other healthcare resources. The goal of this study was to investigate ED use by HIV-infected prisoners transitioning to communities.We evaluated ED use by 151 HIV-infected released prisoners who were enrolled in a randomized controlled trial of directly administered versus self-administered antiretroviral therapy in Connecticut. Primary outcomes were quantity and type of ED visits and correlates of ED use were evaluated with multivariate models by Poisson regression.In the 12 months post-release, there were 227 unique ED contacts made by 85/151 (56% subjects. ED visits were primarily for acute febrile syndromes (32.6% or pain (20.3%, followed by substance use issues (19.4%, trauma (18%, mental illness (11%, and social access issues (4.4%. Compared to those not utilizing the ED, users were more likely to be white, older, and unmarried, with less trust in their physician and poorer perceived physical health but greater social support. In multivariate models, ED use was correlated with moderate to severe depression (IRR = 1.80, being temporarily housed (IRR = 0.54, and alcohol addiction severity (IRR = 0.21 but not any surrogates of HIV severity.EDs are frequent sources of care after prison-release with visits often reflective of social and psychiatric instability. Future interventions should attempt to fill resource gaps, engage released prisoners in continuous HIV care, and address these substantial needs.

Relationship between Organic Carbon Runoff to River and Land Cover

Science.gov (United States)

Kim, G. S.; Lee, S. G.; Lim, C. H.; Lee, W.; Yoo, S.; Kim, S. J.; Heo, S.; Lee, W. K.

2017-12-01

Carbon is an important unit in understanding the ecosystem and energy circulation. Each ecosystem, land, water, and atmosphere, is interconnected through the exchange of energy and organic carbon. In the rivers, primary producers utilize the organic carbon from the land. Understanding the organic carbon uptake into the river is important for understanding the mechanism of river ecosystems. The main organic carbon source of the river is land. However, it is difficult to observe the amount of organic carbon runoff to the river. Therefore, an indirect method should be used to estimate the amount of organic carbon runoff to the river. The organic carbon inflow is caused by the runoff of organic carbon dissolved in water or the inflow of organic carbon particles by soil loss. Therefore, the hydrological model was used to estimate organic carbon runoff through the flow of water. The land cover correlates with soil respiration, soil loss, and so on, and the organic carbon runoff coefficient will be estimated to the river by land cover. Using the organic carbon concentration from water quality data observed at each point in the river, we estimate the amount of organic carbon released from the land. The reason is that the runoff from the watershed converges into the rivers in the watershed, the watershed simulation is conducted based on the water quality data observation point. This defines a watershed that affects organic carbon observation sites. The flow rate of each watershed is calculated by the SWAT (Soil and Water Assessment Tool), and the total organic carbon runoff is calculated by using flow rate and organic carbon concentration. This is compared with the factors related to the amount of organic carbon such as land cover, soil loss, and soil organic carbon, and spatial analysis is carried out to estimate the organic carbon runoff coefficient per land cover.

Assessment of Aprotinin Loaded Microemulsion Formulations for Parenteral Drug Delivery: Preparation, Characterization, in vitro Release and Cytotoxicity Studies.

Science.gov (United States)

Okur, Neslihan Üstündağ; Özdemir, Derya İlem; Kahyaoğlu, Şennur Görgülü; Şenyiğit, Zeynep Ay; Aşıkoğlu, Makbule; Genç, Lütfi; Karasulu, H Yeşim

2015-01-01

The object of the current study was to prepare novel microemulsion formulations of aprotinin for parenteral delivery and to compare in vitro characteristics and release behaviour of different Technetium-99m ((99m)Tc)-Aprotinin loaded microemulsion formulations. In addition, cytotoxicity of microemulsion formulation was evaluated with cell culture studies on human immortalized pancreatic duct epithelial-like cells. For this aim, firstly, pseudo-ternary phase diagrams were plotted to detect the formulation region and optimal microemulsions were characterized for their thermodynamic stability, conductivity, particle size, zeta potential, viscosity, pH and in vitro release properties. For in vitro release studies aprotinin was labelled with (99m)Tc and labelling efficiency, radiochemical purity and stability of the radiolabeled complex were determined by several chromatography techniques. Radiolabeling efficiency of (99m)Tc-Aprotinin was found over than 90% without any significant changes up to 6 hours after labelling at room temperature. After that, in vitro release studies of (99m)Tc-Aprotinin loaded microemulsions were performed with two different methods; dissolution from diffusion cells and dialysis bags. Both methods showed that release rate of (99m)Tc- Aprotinin from microemulsion could be controlled by microemulsion formulations. Drug release from the optimized microemulsion formulations was found lower compared to drug solution at the end of six hours. According to stability studies, the optimized formulation was found to be stable over a period of 12 months. Also, human immortalized pancreatic duct epithelial-like cells were used to evaluate the cytotoxicity of optimum formulation. Developed microemulsion did not reveal cytotoxicity. In conclusion the present study indicated that the M1-APT microemulsion is appropriate for intravenous application of aprotinin.

Aqueous studies of hydrogen sulfide releases from a heavy water extraction facility

International Nuclear Information System (INIS)

Kiser, D.L.

1979-03-01

Upsets in the operation of the wastewater strippers in the 400 Area of the Savannah River Plant have released hydrogen sulfide in quantities as large as 1800 kg to the effluent stream. Fish kills in the swamp area of Beaver Dam Creek have occurred following the large releases. A literature survey revealed volatilization and oxidation as the major loss mechanisms of H 2 S. Laboratory investigations supported the literature survey. The computer code for pollutant transport in a stream, LODIPS, has an option to account for sink-source effects in a stream. Volatilization and oxidation rate constants were developed for the sink option from two H 2 S releases (18 kg and 118 kg) and results were predicted with LODIPS. Based on the predicted concentration-time profiles for various hypothetical cases, releases as small as 568 kg if discharged over a 30-minute period or releases as large as 1818 kg if discharged over a 360-minute period or less are lethal to swamp fish

Impact of IGF-I release kinetics on bone healing: a preliminary study in sheep.

Science.gov (United States)

Luginbuehl, Vera; Zoidis, Evangelos; Meinel, Lorenz; von Rechenberg, Brigitte; Gander, Bruno; Merkle, Hans P

2013-09-01

Spatiotemporal release of growth factors from a delivery device can profoundly affect the efficacy of bone growth induction. Here, we report on a delivery platform based on the encapsulation of insulin-like growth factor I (IGF-I) in different poly(D,L-lactide) (PLA) and poly(D,L-lactide-co-glycolide) (PLGA) microsphere (MS) formulations to control IGF-I release kinetics. In vitro IGF-I release profiles generally exhibited an initial burst (14-36% of total IGF-I content), which was followed by a more or less pronounced dormant phase with little release (2 to 34 days), and finally, a third phase of re-increased IGF-I release. The osteoinductive potential of these different IGF-I PL(G)A MS formulations was tested in studies using 8-mm metaphyseal drill hole bone defects in sheep. Histomorphometric analysis at 3 and 6 weeks after surgery showed that new bone formation was improved in the defects locally treated with IGF-I PL(G)A MS (n=5) as compared to defects filled with IGF-I-free PL(G)A MS (n=4). The extent of new bone formation was affected by the particular release kinetics, although a definitive relationship was not evident. Local administration of IGF-I resulted in down-regulation of inflammatory marker genes in all IGF-I treated defects. The over-expression of growth factor genes in response to IGF-I delivery was restricted to formulations that produced osteogenic responses. These experiments demonstrate the osteoinductive potential of sustained IGF-I delivery and show the importance of delivery kinetics for successful IGF-I-based therapies. Copyright © 2013 Elsevier B.V. All rights reserved.

Study on Resources Assessment of Coal Seams covered by Long-Distance Oil & Gas Pipelines

Science.gov (United States)

Han, Bing; Fu, Qiang; Pan, Wei; Hou, Hanfang

2018-01-01

The assessment of mineral resources covered by construction projects plays an important role in reducing the overlaying of important mineral resources and ensuring the smooth implementation of construction projects. To take a planned long-distance gas pipeline as an example, the assessment method and principles for coal resources covered by linear projects are introduced. The areas covered by multiple coal seams are determined according to the linear projection method, and the resources covered by pipelines directly and indirectly are estimated by using area segmentation method on the basis of original blocks. The research results can provide references for route optimization of projects and compensation for mining right..

Mitigation of strontium and ruthenium release in the CANDU primary heat transport system

International Nuclear Information System (INIS)

McFarlane, J.

1998-03-01

In certain severe accident scenarios, low-volatility fission products can appear to contribute significantly to dose, if treated with undue conservatism. Hence a survey was performed, to see if factors that may mitigate release of strontium and ruthenium could be incorporated into safety analyses, to cover parameters such as location in the fuel matrix under normal operating conditions, release from fuel, transport and deposition in the primary heat transport system and chemistry. In addition chemical equilibrium calculations were performed to investigate the volatility of strontium and ruthenium in the presence of uranium and important fission products. Strontium is very soluble in the U0 2 fuel, up to 12 atom %, and hence release is improbable, particularly under oxidizing conditions until volatilization of the fuel matrix itself occurs. Ruthenium, however, can be released at low temperatures, but only under oxidizing conditions. These may occur during a fuel-handling accident or as a result of an end-fitting failure. Under these conditions, the primary heat transport system cannot be credited for retention. The volatile form of ruthenium, RuO 4 (g), is thermally unstable above 381 K and decomposes to RuO 2 (s) and O 2 (g) upon contact with surfaces, a factor that is likely to minimize the release of ruthenium into the environment. (author)

Extended-release naltrexone for pre-release prisoners: A randomized trial of medical mobile treatment

Science.gov (United States)

Gordon, Michael S.; Vocci, Frank J.; Fitzgerald, Terrence T.; O'Grady, Kevin E.; O'Brien, Charles P.

2017-01-01

Background Extended-release naltrexone (XR-NTX), is an effective treatment for opioid use disorder but is rarely initiated in US prisons or with criminal justice populations. Mobile treatment for chronic diseases have been implemented in a variety of settings. Mobile treatment may provide an opportunity to expand outreach to parolees to surmount barriers to traditional clinic treatment. Methods Male and female prisoners (240) with pre-incarceration histories of opioid use disorder who are within one month of release from prison will be enrolled in this randomized clinical trial. Participants are randomized to one of two study arms: 1) [XR-NTX-OTx] One injection of long-acting naltrexone in prison, followed by 6 monthly injections post-release at a community opioid treatment program; or 2) [XR-NTX+ MMTx] One injection of long-acting naltrexone in prison followed by 6 monthly injections post-release at the patient's place of residence utilizing mobile medical treatment. The primary outcomes are: treatment adherence; opioid use; criminal activity; re-arrest; reincarceration; and HIV risk-behaviors. Results We describe the background and rationale for the study, its aims, hypotheses, and study design. Conclusions The use of long-acting injectable naltrexone may be a promising form of treatment for pre-release prisoners. Finally, as many individuals in the criminal justice system drop out of treatment, this study will assess whether treatment at their place of residence will improve adherence and positively affect treatment outcomes. PMID:28011389

Extended-release naltrexone for pre-release prisoners: A randomized trial of medical mobile treatment.

Science.gov (United States)

Gordon, Michael S; Vocci, Frank J; Fitzgerald, Terrence T; O'Grady, Kevin E; O'Brien, Charles P

2017-02-01

Extended-release naltrexone (XR-NTX), is an effective treatment for opioid use disorder but is rarely initiated in US prisons or with criminal justice populations. Mobile treatment for chronic diseases has been implemented in a variety of settings. Mobile treatment may provide an opportunity to expand outreach to parolees to surmount barriers to traditional clinic treatment. Male and female prisoners (240) with pre-incarceration histories of opioid use disorder who are within one month of release from prison will be enrolled in this randomized clinical trial. Participants are randomized to one of two study arms: 1) [XR-NTX-OTx] One injection of long-acting naltrexone in prison, followed by 6 monthly injections post-release at a community opioid treatment program; or 2) [XR-NTX+ MMTx] One injection of long-acting naltrexone in prison followed by 6 monthly injections post-release at the patient's place of residence utilizing mobile medical treatment. The primary outcomes are: treatment adherence; opioid use; criminal activity; re-arrest; reincarceration; and HIV risk-behaviors. We describe the background and rationale for the study, its aims, hypotheses, and study design. The use of long-acting injectable naltrexone may be a promising form of treatment for pre-release prisoners. Finally, as many individuals in the criminal justice system drop out of treatment, this study will assess whether treatment at their place of residence will improve adherence and positively affect treatment outcomes. ClinicalTrials.gov: NCT02867124. Copyright © 2016 Elsevier Inc. All rights reserved.

Habitat selection and post-release movement of reintroduced brown treecreeper individuals in restored temperate woodland.

Directory of Open Access Journals (Sweden)

Victoria A Bennett

Full Text Available It is essential to choose suitable habitat when reintroducing a species into its former range. Habitat quality may influence an individual's dispersal decisions and also ultimately where they choose to settle. We examined whether variation in habitat quality (quantified by the level of ground vegetation cover and the installation of nest boxes influenced the movement, habitat choice and survival of a reintroduced bird species. We experimentally reintroduced seven social groups (43 individuals of the brown treecreeper (Climacteris picumnus into two nature reserves in south-eastern Australia. We radio-tracked 18 brown treecreepers from release in November 2009 until February 2010. We observed extensive movements by individuals irrespective of the release environment or an individual's gender. This indicated that individuals were capable of dispersing and actively selecting optimum habitat. This may alleviate pressure on wildlife planners to accurately select the most optimum release sites, so long as the species' requirements are met. There was significant variation in movement between social groups, suggesting that social factors may be a more important influence on movement than habitat characteristics. We found a significant effect of ground vegetation cover on the likelihood of settlement by social groups, with high rates of settlement and survival in dry forests, rather than woodland (where the species typically resides, which has implications for the success of woodland restoration. However, overall the effects of variation in habitat quality were not as strong as we had expected, and resulted in some unpredicted effects such as low survival and settlement in woodland areas with medium levels of ground vegetation cover. The extensive movement by individuals and unforeseen effects of habitat characteristics make it difficult to predict the outcome of reintroductions, the movement behaviour and habitat selection of reintroduced individuals

Post-irradiation studies on knock-out and pseudo-recoil releases of fission products from fissioning UO2

International Nuclear Information System (INIS)

Yamagishi, S.; Tanifuji, T.

1976-01-01

By using post-irradiation techniques, in-pile releases of 133 Xe, sup(85m)Kr, 88 Kr, 87 Kr and 138 Xe from UO 2 fissioning at low temperatures below about 200 0 C are studied: these are analyzed into a time-dependent knock-out and time-independent pseudo-recoil releases. For the latter, a 'self knock-out' mechanism is proposed: when a fission fragment loses thoroughly its energy near the UO 2 surface and stops there, it will knock out the surface substances and accordingly the fragment (i.e. the fission product) will be released. The effective thickness of the layer where the self knock-out occurs is found to be approximately 7A. As for the knock-out release, the following is estimated from its dependence on various factors: the knock-out release of fission products occurs from the surface layer with the effective thickness of approximately 20A: the shape of UO 2 matrix knocked out by one fission fragment passing through the surface is equivalent to a cylinder approximately 32A diameter by approximately 27A thick, (i.e. the knock-out coefficient for UO 2 is approximately 660 uranium atoms per knock-out event). On the basis of the above estimations, the conclusions derived from the past in-pile studies of fission gas releases are evaluated. (Auth.)

Comparative steady-state pharmacokinetic study of an extended-release formulation of itopride and its immediate-release reference formulation in healthy volunteers

Directory of Open Access Journals (Sweden)

Yoon S

2014-01-01

Full Text Available Seonghae Yoon,1,* Howard Lee,2,* Tae-Eun Kim,1 SeungHwan Lee,1 Dong-Hyun Chee,3 Joo-Youn Cho,1 Kyung-Sang Yu,1 In-Jin Jang1 1Department of Clinical Pharmacology and Therapeutics, Seoul National University College of Medicine and Hospital, 2Clinical Trials Center, Seoul National University Hospital, 3AbbVie Ltd., Seoul, Republic of Korea *These authors contributed equally to this work Background: This study was conducted to compare the oral bioavailability of an itopride extended-release (ER formulation with that of the reference immediate-release (IR formulation in the fasting state. The effect of food on the bioavailability of itopride ER was also assessed. Methods: A single-center, open-label, randomized, multiple-dose, three-treatment, three-sequence, crossover study was performed in 24 healthy male subjects, aged 22–48 years, who randomly received one of the following treatments for 4 days in each period: itopride 150 mg ER once daily under fasting or fed conditions, or itopride 50 mg IR three times daily in the fasting state. Steady-state pharmacokinetic parameters of itopride, including peak plasma concentration (Cmax and area under the plasma concentration versus time curve over 24 hours after dosing (AUC0–24h, were determined by noncompartmental analysis. The geometric mean ratio of the pharmacokinetic parameters was derived using an analysis of variance model. Results: A total of 24 healthy Korean subjects participated, 23 of whom completed the study. The geometric mean ratio and its 90% confidence interval of once-daily ER itopride versus IR itopride three times a day for AUC0–24h were contained within the conventional bioequivalence range of 0.80–1.25 (0.94 [0.88–1.01], although Cmax was reached more slowly and was lower for itopride ER than for the IR formulation. Food delayed the time taken to reach Cmax for itopride ER, but AUC0–24h was not affected. There were no serious adverse events and both formulations were

Dietary restriction of choline reduces hippocampal acetylcholine release in rats: in vivo microdialysis study.

Science.gov (United States)

Nakamura, A; Suzuki, Y; Umegaki, H; Ikari, H; Tajima, T; Endo, H; Iguchi, A

2001-12-01

We fed rats with a diet deficient in choline for 12 weeks and studied how dietary choline deficiency affected their behavior and their ability to release acetylcholine in discrete regions of rat brain using step-through passive avoidance task and in vivo microdialysis. In comparison with the control, rats fed the choline-deficient diet showed poorer retention of nociceptive memory in the passive avoidance task. Average choline level in cerebrospinal fluid in the choline-deficient group was significantly less (33.1%) than that of control rats. In vivo microdialysis showed no difference in the pattern of acetylcholine release enhanced by intraperitoneal administration of scopolamine hydrochloride (2 mg/kg) in the striatum between the two groups, whereas in the hippocampus, the maximum and subsequent increase of acetylcholine from the baseline by scopolamine injection was significantly lower in the choline-deficient group than in the control. From the results of our study, we speculate that long-term dietary restriction of choline can affect extra- and intracellular sources of substrates required for acetylcholine synthesis, and eventually limit the ability to release acetylcholine in the hippocampus. Reduced capacity to release acetylcholine in the hippocampus implies that the mechanism, maintaining acetylcholine synthesis on increased neuronal demand, may vary in discrete regions of the brain in response to dietary manipulation. The vulnerability of the mechanism in the hippocampus to dietary choline restriction is indicated by impaired mnemonic performance we observed.

Benchmarking Controlled Trial—a novel concept covering all observational effectiveness studies

Science.gov (United States)

Malmivaara, Antti

2015-01-01

Abstract The Benchmarking Controlled Trial (BCT) is a novel concept which covers all observational studies aiming to assess effectiveness. BCTs provide evidence of the comparative effectiveness between health service providers, and of effectiveness due to particular features of the health and social care systems. BCTs complement randomized controlled trials (RCTs) as the sources of evidence on effectiveness. This paper presents a definition of the BCT; compares the position of BCTs in assessing effectiveness with that of RCTs; presents a checklist for assessing methodological validity of a BCT; and pilot-tests the checklist with BCTs published recently in the leading medical journals. PMID:25965700

Benchmarking Controlled Trial--a novel concept covering all observational effectiveness studies.

Science.gov (United States)

Malmivaara, Antti

2015-06-01

The Benchmarking Controlled Trial (BCT) is a novel concept which covers all observational studies aiming to assess effectiveness. BCTs provide evidence of the comparative effectiveness between health service providers, and of effectiveness due to particular features of the health and social care systems. BCTs complement randomized controlled trials (RCTs) as the sources of evidence on effectiveness. This paper presents a definition of the BCT; compares the position of BCTs in assessing effectiveness with that of RCTs; presents a checklist for assessing methodological validity of a BCT; and pilot-tests the checklist with BCTs published recently in the leading medical journals.

Controlled release effervescent buccal discs of buspirone hydrochloride: in vitro and in vivo evaluation studies.

Science.gov (United States)

Jaipal, A; Pandey, M M; Charde, S Y; Sadhu, N; Srinivas, A; Prasad, R G

2016-01-01

In the present study controlled release effervescent buccal discs of buspirone hydrochloride (BS) were designed using HPMC as rate controlling and bioadhesive polymer by direct compression method. Sodium bicarbonate and citric acid were used in varying amounts as effervescence forming agents. Carbon dioxide evolved due to reaction of sodium bicarbonate and citric acid was explored for its potential as buccal permeation enhancer. The designed buccal discs were evaluated for physical characteristics and in vitro drug release studies. Bioadhesive behavior of designed buccal discs was assessed using texture analyzer. In vivo animal studies were performed in rabbits to study bioavailability of BS in the designed buccal discs and to establish permeation enhancement ability of carbon dioxide. It was observed that effervescent buccal discs have faster drug release compared to non-effervescent buccal discs in vitro and effervescent buccal discs demonstrated significant increase in bioavailability of drug when compared to non-effervescent formulation. Hence, effervescent buccal discs can be used as an alternative to improve the drug permeation resulting in better bioavailability. However, the amount of acid and base used for generation of carbon dioxide should be selected with care as this may damage the integrity of bioadhesive dosage form.

A study of the performance of a reclamation soil cover placed over an oilsands coke deposit

Energy Technology Data Exchange (ETDEWEB)

Fenske, D.S.; Barbour, S.L. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Civil Engineering; Qualizza, C. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

2006-07-01

Coke is a solid, carbonaceous residue that forms during the cracking of high-boiling point distillates and is one of the by-products of petroleum extraction from oilsands. Coke is known as a possible future energy source and therefore, must be stored within the reclaimed landscape in a form that allows it to be recovered. In addition, it also could be used as a low-density capping material over soft tailings. This paper presented the results of a study that examined the effects of coke in the environment. The study involved construction of two small instrumented watersheds at Syncrude Canada's Mildred Lake Settling Basin. Preliminary field data, highlighting the moisture dynamics within the covers and the underlying coke were discussed. Sand tailings underlie the hydraulically placed coke deposit. Overlying the coke were two different reclamation soil covers constructed of a peat/mineral mix over glacial or glacial lacustrine soils. Placing the finer textured soil cover over coarser grained coke produced a textural or capillary break which enhanced moisture storage for plant use while minimizing deep percolation of infiltrating water. The site has been instrumented with a meteorological station; automated soil stations to monitor suction, water content and temperature through the cover profile; lysimeters to collect net percolation; access tubes for water content monitoring; gas sampling points at depth in the coke; and standpipe piezometers to monitor water chemistry and total head in the coke at depth. 10 refs., 2 tabs., 16 figs.

A study on the transfer of heavy methals released by Chinese commercial products.

Science.gov (United States)

Olori, Angelo; Campopiano, Antonella; Cannizzaro, Annapaola; Basili, Fulvio

2013-01-01

Studies by The World trade Organization (WTO) and the Organization for the Economic Cooperation and Development (OECD) state that the trade on counterfeit goods corresponds to 10% of the global trade and it is worth 450 billion dollars. In this work we studied the transfer of toxic metals released by some Chinese watches causing significant allergic dermatitis. Several samples of dust released from metal parts got collected. Such powders were observed at the Electron Microscope complete with EDAX spectrometer. In all the studied dust samples we identified the following chemical elements: Cu, Ni and Zn. The SEM analysis has identified two predominant phases such as pure nickel and brass alloy (Cu-Zn). The first metal subjected to cession and to corrosion phenomena is nickel. The main causes of corrosion in the studied materials were due to the presence of chloride ions. Among the ceased metals found in our study nickel is the most dangerous. Scientific evidence now agree that nickel and certain nickel compounds are toxic and highly harmful to human health they indeed cause allergic contact dermatitis (DAC).

THz TDS of substance covered by disordered structure

Science.gov (United States)

Trofimov, V. A.; Zagursky, D. Y.; Zakharova, I. G.

2016-04-01

Computer simulation of a few-cycle pulse interaction with a substance covered by disordered structure is performed in order to study the effects imposed on spectra of transmitted and reflected pulses by presence of the cover. The substance is described by semi-classic approach and the cover is described by classic electrodynamics equations for linear isotropic medium. The cover consists of a number of layers with different properties which is considered to be the cause of the distortions. The influence of relation between pulse wavelength and cover layer thickness is illustrated. Computer simulation results are compared with those of physical experiments conducted for paper and other common materials.

In vitro effect of. Delta. sup 9 -tetrahydrocannabinol to stimulate somatostatin release and block that of luteinizing hormone-releasing hormone by suppression of the release of prostaglandin E sub 2

Energy Technology Data Exchange (ETDEWEB)

Rettori, V.; Aguila, M.C.; McCann, S.M. (Univ. of Texas Southwestern Medical Center at Dallas (United States)); Gimeno, M.F.; Franchi, A.M. (Centro de Estudios Farmacologicos y de Principios Naturales, Buenos Aires (Argentina))

1990-12-01

Previous in vivo studies have shown that {Delta}{sup 9}-tetrahydrocannabinol (THC), the principal active ingredient in marijuana, can suppress both luteinizing hormone (LH) and growth hormone (GH) secretion after its injection into the third ventricle of conscious male rats. The present studies were deigned to determine the mechanism of these effects. Various doses of THC were incubated with either stalk median eminence fragments (MEs) or mediobasal hypothalamic (MBH) fragments in vitro. Although THC (10 nM) did not alter basal release of LH-releasing hormone (LHRH) from MEs in vitro, it completely blocked the stimulatory action of dopamine or nonrepinephrine on LHRH release. The effective doses to block LHRH release were associated with a blockade of synthesis and release of prostaglandin E{sub 2} (PGE{sub 2}) from MBH in vitro. In contrast to the suppressive effect of THC on LHRH release, somatostatin release from MEs was enhanced in a dose-related manner with a minimal effective dose of 1 nM. Since PGE{sub 2} suppresses somatostatin release, this enhancement may also be related to the suppressive effect of THC on PGE{sub 2} synthesis and release. The authors speculate that these actions are mediated by the recently discovered THC receptors in the tissue. The results indicate that the suppressive effect of THC on LH release is mediated by a blockade of LHRH release, whereas the suppressive effect of the compound on growth hormone release is mediated, at least in part, by a stimulation of somatostatin release.

Land Cover Classification Using ALOS Imagery For Penang, Malaysia

International Nuclear Information System (INIS)

Sim, C K; Abdullah, K; MatJafri, M Z; Lim, H S

2014-01-01

This paper presents the potential of integrating optical and radar remote sensing data to improve automatic land cover mapping. The analysis involved standard image processing, and consists of spectral signature extraction and application of a statistical decision rule to identify land cover categories. A maximum likelihood classifier is utilized to determine different land cover categories. Ground reference data from sites throughout the study area are collected for training and validation. The land cover information was extracted from the digital data using PCI Geomatica 10.3.2 software package. The variations in classification accuracy due to a number of radar imaging processing techniques are studied. The relationship between the processing window and the land classification is also investigated. The classification accuracies from the optical and radar feature combinations are studied. Our research finds that fusion of radar and optical significantly improved classification accuracies. This study indicates that the land cover/use can be mapped accurately by using this approach

A comparison of the extended-release and standard-release formulations of tacrolimus in de novo kidney transplant recipients: a 12-month outcome study.

Science.gov (United States)

Fanous, Helen; Zheng, Rebecca; Campbell, Carolyn; Huang, Michael; Nash, Michelle M; Rapi, Lindita; Zaltzman, Jeffrey S; Prasad, G V Ramesh

2013-02-01

BACKGROUND: Limited comparative data are available on the outcomes between extended-release and standard-release tacrolimus when used de novo in kidney transplant recipients (KTRs). METHODS: We identified KTRs transplanted at our institution during 2009-10 routinely prescribed extended-release tacrolimus and compared them with those transplanted during 2008-09 prescribed standard-release tacrolimus. Graft function (eGFR by MDRD-7 equation) at 12 months post-transplant (primary outcome); new-onset diabetes and other cardiovascular risk factors, BK viremia incidence, acute rejection, and graft survival to 12 months (secondary outcomes) were compared by intent-to-treat analysis. Time-to-steady-state concentration and number of dose adjustments required to attain steady state were recorded. RESULTS: There were no important demographic differences between the extended-release (N = 106) and standard-release (N = 95) cohorts. The estimated glomerular filtration rate (eGFR) at 12 months was similar (58.8 ± 17 versus 59.2 ± 18 mL/min/1.73 m(2), P = 0.307). There was no difference in new-onset diabetes (17 versus 20%, P = 0.581), BK viremia (10 versus 7%, P = 0.450), acute rejection (7 versus 16%, P = 0.067) or graft survival (97 versus 95%, P = 0.301). Time-to-steady state was similar (9.2 ± 1.1 versus 8.1 ± 4.7 days, P = 0.490) although extended-release patients required fewer adjustments to attain steady state (1.2 ± 1.7 [0-8] versus 1.7 ± 1.5 [0-7], P = 0.030) but a similar dose (7.2 ± 2.4 [2-17] versus 7 ± 2.7 [2-16] mg/day, P = 0.697). CONCLUSION: De novo KTRs prescribed extended-release or standard-release tacrolimus demonstrate similar 12-month outcomes.

Cover Crop-Based, Organic Rotational No-Till Corn and Soybean Production Systems in the Mid-Atlantic United States

Directory of Open Access Journals (Sweden)

John M. Wallace

2017-04-01

Full Text Available Cover crop-based, organic rotational no-till (CCORNT corn and soybean production is becoming a viable strategy for reducing tillage in organic annual grain systems in the mid-Atlantic, United States. This strategy relies on mechanical termination of cover crops with a roller-crimper and no-till planting corn and soybean into cover crop mulches. Here, we report on recent research that focuses on integrated approaches for crop, nutrient and pest management in CCORNT systems that consider system and regional constraints for adoption in the mid-Atlantic. Our research suggests that no-till planting soybean into roller-crimped cereal rye can produce consistent yields. However, constraints to fertility management have produced less consistent no-till corn yields. Our research shows that grass-legume mixtures can improve N-release synchrony with corn demand and also improve weed suppression. Integration of high-residue inter-row cultivation improves weed control consistency and may reduce reliance on optimizing cover crop biomass accumulation for weed suppression. System-specific strategies are needed to address volunteer cover crops in later rotational phases, which result from incomplete cover crop termination with the roller crimper. The paucity of adequate machinery for optimizing establishment of cash crops into thick residue mulch remains a major constraint on CCORNT adoption. Similarly, breeding efforts are needed to improve cover crop germplasm and develop regionally-adapted varieties.

Release of segregated nuclides from spent fuel

Energy Technology Data Exchange (ETDEWEB)

Johnson, L.H.; Tait, J.C. [Atomic Energy Canada Ltd., Pinawa, MB (Canada). Whiteshell Laboratories

1997-10-01

The potential release of fission and activation products from spent nuclear fuel into groundwater after container failure in the Swedish deep repository is discussed. Data from studies of fission gas release from representative Swedish BWR fuel are used to estimate the average fission gas release for the spent fuel population. Information from a variety of leaching studies on LWR and CANDU fuel are then reviewed as a basis for estimating the fraction of the inventory of key radionuclides that could be released preferentially (the Instant Release Fraction of IRF) upon failure of the fuel cladding. The uncertainties associated with these estimates are discussed. 33 refs, 6 figs, 3 tabs.

Effect of Food Emulsifiers on Aroma Release

Directory of Open Access Journals (Sweden)

Jia-Jia Li

2016-04-01

Full Text Available This study aimed to determine the influence of different emulsifiers or xanthan-emulsifier systems on the release of aroma compounds. Solid-phase microextraction (SPME and GC-MS were used to study the effects of varying concentrations of xanthan gum, sucrose fatty acid ester, Tween 80 and soybean lecithin on the release of seven aroma compounds. The effects of the emulsifier systems supplemented with xanthan gum on aroma release were also studied in the same way. The results showed varying degrees of influence of sucrose fatty acid ester, soybean lecithin, Tween 80 and xanthan gum on the release of aroma compounds. Compared with other aroma compounds, ethyl acetate was more likely to be conserved in the solution system, while the amount of limonene released was the highest among these seven aroma compounds. In conclusion, different emulsifiers and complexes showed different surface properties that tend to interact with different aroma molecules. The present studies showed that the composition and structure of emulsifiers and specific interactions between emulsifiers and aroma molecules have significant effects on aroma release.

Analgesic Efficacy of a New Immediate-Release/Extended-Release Formulation of Ibuprofen: Results From Single- and Multiple-Dose Postsurgical Dental Pain Studies.

Science.gov (United States)

Christensen, Steven; Paluch, Ed; Jayawardena, Shyamalie; Daniels, Stephen; Meeves, Suzanne

2017-05-01

Analgesic effects of ibuprofen immediate-release/extended-release (IR/ER) 600-mg tablets were evaluated in 2 randomized, double-blind, placebo-controlled dental pain studies. Patients 16-40 years old with moderate-severe pain following third-molar extraction received single-dose ibuprofen 600 mg IR/ER (formulation A or B), naproxen sodium 220 mg, or placebo (2:2:2:1; study 1) or 4 doses of ibuprofen 600 mg IR/ER (formulation A) or placebo (1:1; study 2). In study 1 (n = 196), mean (standard deviation [SD]) time-weighted sum of pain intensity difference scores for placebo, ibuprofen IR/ER A, ibuprofen IR/ER B, and naproxen, respectively, were 0.05 (9.2), 16.87 (9.4), 17.34 (10.5), and 12.66 (10.0) over 0-12 hours and -0.03 (4.1), 6.57 (4.4), 7.14 (5.2), and 5.14 (5.0) over 8-12 hours (all P ibuprofen IR/ER, respectively (P ibuprofen. Gastrointestinal adverse events predominated with placebo both after study medication administration and after rescue medication use, if applicable. Ibuprofen 600 mg IR/ER provided safe and effective analgesia after single and multiple doses. © 2016, The American College of Clinical Pharmacology.

Coupling Cover Crops with Alternative Swine Manure Application Strategies: Manure-15N Tracer Studies

Science.gov (United States)

Integration of rye cover crops with alternative liquid swine (Sus scrofa L.) manure application strategies may enhance retention of manure N in corn (Zea mays L.) - soybean [Glycine max (L.) Merr] cropping systems. The objective of this study was to quantify uptake of manure derived-N by a rye (Seca...

THE PAN-STARRS 1 PHOTOMETRIC REFERENCE LADDER, RELEASE 12.01

International Nuclear Information System (INIS)

Magnier, E. A.; Tonry, J. L.; Burgett, W. S.; Chambers, K. C.; Flewelling, H. A.; Kaiser, N.; Kudritzki, R.-P.; Morgan, J. S.; Sweeney, W. E.; Schlafly, E.; Finkbeiner, D.; Juric, M.; Stubbs, C. W.; Price, P. A.

2013-01-01

As of 2012 January 21, the Pan-STARRS 1 3π Survey has observed the 3/4 of the sky visible from Hawaii with a minimum of 2 and mean of 7.6 observations in five filters, g P1 , r P1 , i P1 , z P1 , y P1 . Now at the end of the second year of the mission, we are in a position to make an initial public release of a portion of this unprecedented data set. This article describes the PS1 Photometric Ladder, Release 12.01. This is the first of a series of data releases to be generated as the survey coverage increases and the data analysis improves. The Photometric Ladder has rungs every hour in right ascension and at four intervals in declination. We will release updates with increased area coverage (more rungs) from the latest data set until the PS1 survey and the final re-reduction are completed. The currently released catalog presents photometry of ∼1000 objects per square degree in the rungs of the ladder. Saturation occurs at g P1 , r P1 , i P1 ∼ 13.5; z P1 ∼ 13.0; and y P1 ∼ 12.0. Photometry is provided for stars down to g P1 , r P1 , i P1 ∼ 19.1 in the AB system. This data release depends on the rigid 'Ubercal' photometric calibration using only the photometric nights, with systematic uncertainties of (8.0, 7.0, 9.0, 10.7, 12.4) mmag in (g P1 , r P1 , i P1 , z P1 , y P1 ). Areas covered only with lower quality nights are also included, and have been tied to the Ubercal solution via relative photometry; photometric accuracy of the non-photometric regions is lower and should be used with caution.

Chemical incidents resulted in hazardous substances releases in the context of human health hazards

Directory of Open Access Journals (Sweden)

Anna Pałaszewska-Tkacz

2017-02-01

Full Text Available Objectives: The research purpose was to analyze data concerning chemical incidents in Poland collected in 1999–2009 in terms of health hazards. Material and Methods: The data was obtained, using multimodal information technology (IT system, from chemical incidents reports prepared by rescuers at the scene. The final analysis covered sudden events associated with uncontrolled release of hazardous chemical substances or mixtures, which may potentially lead to human exposure. Releases of unidentified substances where emergency services took action to protect human health or environment were also included. Results: The number of analyzed chemical incidents in 1999–2009 was 2930 with more than 200 different substances released. The substances were classified into 13 groups of substances and mixtures posing analogous risks. Most common releases were connected with non-flammable corrosive liquids, including: hydrochloric acid (199 cases, sulfuric(VI acid (131 cases, sodium and potassium hydroxides (69 cases, ammonia solution (52 cases and butyric acid (32 cases. The next group were gases hazardous only due to physico-chemical properties, including: extremely flammable propane-butane (249 cases and methane (79 cases. There was no statistically significant trend associated with the total number of incidents. Only with the number of incidents with flammable corrosive, toxic and/or harmful liquids, the regression analysis revealed a statistically significant downward trend. The number of victims reported was 1997, including 1092 children and 18 fatalities. Conclusions: The number of people injured, number of incidents and the high 9th place of Poland in terms of the number of Seveso establishments, and 4 times higher number of hazardous industrial establishments not covered by the Seveso Directive justify the need for systematic analysis of hazards and their proper identification. It is advisable enhance health risk assessment, both qualitative and

Preparation of berbamine loaded chitosan-agarose microspheres and in vitro release study

Directory of Open Access Journals (Sweden)

Zhang Hu

2012-01-01

Full Text Available Berbamine loaded chitosan-agarose microspheres were prepared using a water-in-oil emulsion technique. Optimum preparing parameters were determined by orthogonal experiments as follows: ratio of berbamine to chitosan (w/w is 1:10; percentage of emulsifier (span 80, v/v is 6%; volume of glutaraldehyde is 2 mL; and reaction temperature is 70 ºC. Under these optimal conditions, the encapsulation efficiency and loading capacity of microspheres are 84.57% and 8.44%, respectively. The swelling tests showed that the microspheres possessed higher swelling ratio at pH 7.4 than at pH 1.2. FTIR indicated that berbamine had been successfully loaded in the chitosan-agarose microspheres by physical entrapment. In vitro release studies showed that berbamine was released from microspheres in a significantly sustained fashion.

Release kinetics of tocopherol and quercetin from binary antioxidant controlled-release packaging films.

Science.gov (United States)

Chen, Xi; Lee, Dong Sun; Zhu, Xuntao; Yam, Kit L

2012-04-04

This paper investigated the feasibility of manipulating packaging polymers with various degrees of hydrophobicity to release two antioxidants, tocopherol and quercetin, at rates suitable for long-term inhibition of lipid oxidation in food. For example, one antioxidant can be released at a fast rate to provide short-term/intermediate protection, whereas the other antioxidant can be released at a slower rate to provide intermediate/long-term protection of lipid oxidation. Controlled-release packaging films containing tocopherol and quercetin were produced using ethylene vinyl alcohol (EVOH), ethylene vinyl acetate (EVA), low-density polyethylene (LDPE), and polypropylene (PP) polymers; the release of these antioxidants to 95% ethanol (a fatty food simulant) was measured using UV-vis spectrophotometry, and Fickian diffusion models with appropriate initial and boundary conditions were used to fit the data. For films containing only quercetin, the results show that the release of quercetin was much faster but lasted for a much shorter time for hydrophilic polymers (EVOH and EVA) than for hydrophobic polymers (LDPE and PP). For binary antioxidant films containing tocopherol and quercetin, the results show that tocopherol released more rapidly but for a shorter period of time than quercetin in LDPE and EVOH films, and the difference is more pronounced for LDPE films than EVOH films. The results also show the presence of tocopherol can accelerate the release of quercetin. Although none of the films produced is acceptable for long-term lipid oxidation inhibition, the study provides encouraging results suggesting that acceptable films may be produced in the future using polymer blend films.

Tritium sorption by cement and subsequent release

International Nuclear Information System (INIS)

Ono, F.; Yamawaki, M.

1995-01-01

In a fusion reactor or tritium-handling facilities, contamination of concrete by tritium and subsequent release from it to the reator or experimental room is a matter of problem for safe control of tritium and management of operational environment. In order to evaluate this tritium behavior, interaction of tritiated water with concrete or cement should be clarified. In the present study, HTO sorption and subsequent release from cement were experimentally studied.(1)Sorption experiments were conducted using columns packed with cement particles of different sizes. From the analysis of the breakthrough curve, tritium diffusivity in macropores and microparticles were evaluated.(2)From the short-term tritium release experiments, effective desorption rate constants were evaluated and the effects of temperature and moisture were studied.(3)In the long-term tritium release experiments to 6000h, the tritium release mechanism was found to be composed of three kinds of water: initially from capillary water, and in the second stage from gel water and from the water in the cement crystal.(4)Tritium release behavior by heat treatment to 800 C was studied. A high temperature above 600 C was required for the tritium trapped in the crystal water to be released. (orig.)

SRTM Data Release for Eurasia, Index Map and Colored Height

Science.gov (United States)

2004-01-01

The colored regions of this map show the extent of digital elevation data recently released by the Shuttle Radar Topography Mission (SRTM). This release includes data for most of Europe and Asia plus numerous islands in the Indian and Pacific Oceans. SRTM flew on board the Space Shuttle Endeavour in February 2000 and used an interferometric radar system to map the topography of Earth's landmass between latitudes 56 degrees south and 60 degrees north.The data were processed into geographic 'tiles,' each of which represents one by one degree of latitude and longitude. A degree of latitude measures 111 kilometers (69 miles) north-south, and a degree of longitude measures 111 kilometers or less east-west, decreasing away from the equator. The data are being released to the public on a continent-by-continent basis. This Eurasia segment includes 5,940 tiles, more than a third of the total data set. Previous releases covered North America and South America. Forthcoming releases will include Africa-Arabia and Australia plus an 'Islands' release for those islands not included in the continental releases. Together these data releases constitute the world's first high-resolution, near-global elevation model. The resolution of the publicly released data is three arcseconds (1/1,200 of a degree of latitude and longitude), which is about 90 meters (295 feet).European coverage in the current data release stretches eastward from the British Isles and the Iberian Peninsula in the west, across the Alps and Carpathian Mountains, as well as the Northern European Plain, to the Ural and Caucasus Mountains bordering Asia. The Asian coverage includes a great diversity of landforms, including the Tibetan Plateau, Tarin Basin, Mongolian Plateau, and the mountains surrounding Lake Baikal, the world's deepest lake. Mt. Everest in the Himalayas, at 8,848 meters (29,029 feet) is the world's highest mountain. From India's Deccan Plateau, to Southeast Asia, coastal China, and Korea, various

Spatio-temporal change in forest cover and carbon storage considering actual and potential forest cover in South Korea.

Science.gov (United States)

Nam, Kijun; Lee, Woo-Kyun; Kim, Moonil; Kwak, Doo-Ahn; Byun, Woo-Hyuk; Yu, Hangnan; Kwak, Hanbin; Kwon, Taesung; Sung, Joohan; Chung, Dong-Jun; Lee, Seung-Ho

2015-07-01

This study analyzes change in carbon storage by applying forest growth models and final cutting age to actual and potential forest cover for six major tree species in South Korea. Using National Forest Inventory data, the growth models were developed to estimate mean diameter at breast height, tree height, and number of trees for Pinus densiflora, Pinus koraiensis, Pinus rigida, Larix kaempferi, Castanea crenata and Quercus spp. stands. We assumed that actual forest cover in a forest type map will change into potential forest covers according to the Hydrological and Thermal Analogy Groups model. When actual forest cover reaches the final cutting age, forest volume and carbon storage are estimated by changed forest cover and its growth model. Forest volume between 2010 and 2110 would increase from 126.73 to 157.33 m(3) hm(-2). Our results also show that forest cover, volume, and carbon storage could abruptly change by 2060. This is attributed to the fact that most forests are presumed to reach final cutting age. To avoid such dramatic change, a regeneration and yield control scheme should be prepared and implemented in a way that ensures balance in forest practice and yield.

VizieR Online Data Catalog: VIKING catalogue data release 2 (Edge+, 2016)

Science.gov (United States)

Edge, A.; Sutherland, W.; Viking Team

2016-10-01

The VIKING survey with VISTA (ESO programme ID 179.A-2004) is a wide area (eventually 1500 sq.degrees), intermediate-depth (5-sigma detection limit J=21 on Vega system) near-infrared imaging survey, in the five broadband filters Z, Y, J, H, Ks. The planned sky coverage is at high galactic latitudes, and includes two main stripes 70x10°2 each: one in the South Galactic cap near Dec~-30°, and one near Dec~0° in the North galactic cap; in addition, there are two smaller outrigger patches called GAMA09 and CFHLS-W1. Science goals include z>6.5 quasars, extreme brown dwarfs, and multiwavelength coverage and identifications for a range of other imaging surveys, notably VST-KIDS and Herschel-ATLAS. This second public data release of VIKING data covers all of the highest quality data taken between the start of the survey (12th of November 2009) and the end of Period 92 (30th September 2013). This release supersedes the first release (VIKING and VIKING CAT published 28.06.2013 and 16.12.2013 respectively) as it includes improved CASU processing (V1.3) that gives better tile grouting and zero point corrections This release contains 396 tiles with coverage in all five VIKING filters, 379 of which have a deep co-add in J, and an additional 81 with at least two filters where the second OB has not been executed yet or one filter in an OB was poor quality. These 477 fields cover a total of ~690 square degrees and the resulting catalogues include a total of 46,270,162 sources (including low-reliability single-band detections). The imaging and catalogues (both single-band and band-merged) total 839.3GB. The coverage in each of the five sub-areas is not completely contiguous but any inter-tile gaps are relatively small. More details can be found in the accompanying documentation: vikingcatdr2.pdf (2 data files).

Computational Studies of Drug Release, Transport and Absorption in the Human Intestines

Science.gov (United States)

Behafarid, Farhad; Brasseur, J. G.; Vijayakumar, G.; Jayaraman, B.; Wang, Y.

2016-11-01

Following disintegration of a drug tablet, a cloud of particles 10-200 μm in diameter enters the small intestine where drug molecules are absorbed into the blood. Drug release rate depends on particle size, solubility and hydrodynamic enhancements driven by gut motility. To quantify the interrelationships among dissolution, transport and wall permeability, we apply lattice Boltzmann method to simulate the drug concentration field in the 3D gut released from polydisperse distributions of drug particles in the "fasting" vs. "fed" motility states. Generalized boundary conditions allow for both solubility and gut wall permeability to be systematically varied. We apply a local 'quasi-steady state' approximation for drug dissolution using a mathematical model generalized for hydrodynamic enhancements and heterogeneity in drug release rate. We observe fundamental differences resulting from the interplay among release, transport and absorption in relationship to particle size distribution, luminal volume, motility, solubility and permeability. For example, whereas smaller volume encourages higher bulk concentrations and reduced release rate, it also encourages higher absorption rate, making it difficult to generalize predictions. Supported by FDA.

A study on programmed drug release from tablets

NARCIS (Netherlands)

Veen, Jacoba van der

1993-01-01

This thesis shows the extension of the applicability of the megaloporous system for drugs with different physico-chemical properties, like solubility and pK.. Procaine HC1, a highly soluble drug, can successfully be formulated in the programmed release megaloporous system, by using Carnauba wax,

Study of drug release and tablet characteristics of silicone adhesive matrix tablets.

Science.gov (United States)

Tolia, Gaurav; Li, S Kevin

2012-11-01

Matrix tablets of a model drug acetaminophen (APAP) were prepared using a highly compressible low glass transition temperature (T(g)) polymer silicone pressure sensitive adhesive (PSA) at various binary mixtures of silicone PSA/APAP ratios. Matrix tablets of a rigid high T(g) matrix forming polymer ethyl cellulose (EC) were the reference for comparison. Drug release study was carried out using USP Apparatus 1 (basket), and the relationship between the release kinetic parameters of APAP and polymer/APAP ratio was determined to estimate the excipient percolation threshold. The critical points attributed to both silicone PSA and EC tablet percolation thresholds were found to be between 2.5% and 5% w/w. For silicone PSA tablets, satisfactory mechanical properties were obtained above the polymer percolation threshold; no cracking or chipping of the tablet was observed above this threshold. Rigid EC APAP tablets showed low tensile strength and high friability. These results suggest that silicone PSA could eliminate issues related to drug compressibility in the formulation of directly compressed oral controlled release tablets of poorly compressible drug powder such as APAP. No routinely used excipients such as binders, granulating agents, glidants, or lubricants were required for making an acceptable tablet matrix of APAP using silicone PSA. Copyright © 2012 Elsevier B.V. All rights reserved.

[Influence of polymer type on the physical properties and the release study of papaverine hydrochloride from tablets].

Science.gov (United States)

Kasperek, Regina; Polski, Andrzej; Sobótka-Polska, Karolina; Poleszak, Ewa

2014-01-01

Polymers are widely used in drug manufacturing. Researchers studied their impact on the bioavailability of active substances or on physical properties of tablets for many years. To study the influence of polymer excipients, such as microcrystalline cellulose (Avicel PH 101, Avicel PH 102), croscarmellose sodium, crospovidone or polyvinylpyrrolidone, on the release profile of papaverine hydrochloride from tablets and on the physical properties of tablets. Six series of uncoated tablets were prepared by indirect method, with previous wet granulation. Tablets contained papaverine hydrochloride and various excipients. The physical properties of the prepared granules, tablets and the release profile of papaverine hydrochloride from tablets were examined. The content of papaverine hydrochloride from the release study were determined spectrophotometrically. All tablets met the pharmacopoeia requirements during following tests: the disintegration time of tablets, uncoated tablets resistance to abrasion, the weight uniformity and dose formulations, their dimensions, the resistance to crushing of tablets and the drug substance content in the tablet. In four cases more than 80% of papaverine was released up to 2 min, in one formula it was up to 5 min, and in last one up to 10 min. Tablets containing crospovidone disintegrated faster than tablets with croscarmellose sodium. Adding gelatinized starch to the tablet composition increased the disintegration time, hardness and delayed the release of papaverine. During the wet granulation process, granules containing polyvinylpyrrolidone were characterized by a suitable flow properties and slightly prolonged disintegration time. Tablets containing Avicel PH 102 compared to tablets with Avicel PH 101 had less weight loss during the test of mechanical resistance, improved hardness and faster release profile of papaverine from tablets.

Fabrication of ketoprofen controlled-release tablets using biopolymeric hydrophilic matrices: in-vitro studies

International Nuclear Information System (INIS)

Rashid, S.; Khan, B.A.; Khan, G.M.

2017-01-01

Ketoprofen is propionic acid derivative and belongs to the Non-Steroidal anti-inflammatory group of drugs. Due to the short half-life, dosage frequency, patient non-compliance and side effects such as gastrointestinal disturbance, peptic ulceration and gastro intest inal bleeding, it is considered to be good candidate for formulation into controlled release dosage forms. Directly compressed controlled released ( CR) tablets using Acrylic acid derivatives were prepared and evaluated. In-Vitro Physicochemical assessment of the formulated tablets were performed using different physicochemical, dimensional and quality control tests such as weight variation, thickness and diameter, hardness test, friability test, content uniformity, disintegration and dissolution testing. Results of all these tests were formed within acceptable range. The effect of carbomer polymers on the tablet characteristics, drug release rates, release patterns and release kinetics were investigated. The F2-metric technique was applied to compare dissolution profiles of ketoprofen and carbopol tablets with ketoprofen SR - tablets taken as standard preparation. Acrylic acid derivatives when used as polymers resulted in an extended release profile of about 12 h. Using Higuchi's model and the Korsmeyer equation, the drug release mechanism from the tablets was found to be an anomalous type involving diffusion and erosion. Controlled- release Ketoprofen tablets appear to be a good choice for the symptomatic treatment of rheumatoid arthritis and osteoarthritis. Convenient once-daily administration may help improve patient's compliance. (author)

Does Endoscopic Piriformis Tenotomy Provide Safe and Complete Tendon Release? A Cadaver Study.

Science.gov (United States)

Coulomb, Rémy; Khelifi, Anis; Bertrand, Martin; Mares, Olivier; May, Olivier; Marchand, Philippe; Kouyoumdjian, Pascal

2018-05-28

Endoscopic piriformis release (EPR) is among the available treatments for piriformis syndrome. This procedure typically involves dividing the muscle near the sciatic nerve in the sub-gluteal space, which contains numerous blood vessels and nerves. The objectives of this prospective cadaver study were: 1) to assess the reproducibility and quality of endoscopic piriformis tenotomy near the greater trochanter; 2) to detect iatrogenic injuries to the lateral hip rotators, nerves, and vessels; 3) and to define the surgical safety margins relative to the sciatic nerve and inferior gluteal bundle. EPR at the greater trochanter ensures full release of the muscle with a limited risk of neuro-vascular injury. EPR was performed via two portals on 10 cadaver hips preserved in zinc chloride and placed in the prone position. A third, ancillary portal was required in 7 cases. The area was then dissected with the Kocher-Langenbeck approach to allow an assessment of the tenotomy, detect iatrogenic injuries, and measure the distances separating the tenotomy site from the sciatic nerve and inferior gluteal artery. Complete tenotomy was achieved in 9 (90%) cases. The tendon adhered to the capsule in 2 (20%) cases and showed acquired avulsion in 1 case. No injuries to the sciatic nerve or inferior gluteal artery occurred. Mean distances from the tenotomy site were 5.21±0.59cm (range, 4.5-6.6cm) for the sciatic nerve and 7.1±0.89cm (range, 5.4-8.5cm) for the inferior gluteal artery. EPR by a tenotomy at the greater trochanter without sciatic nerve release provides full release of the muscle with satisfactory safety margins and a short learning curve. III, prospective cadaver case-control study. Copyright © 2018. Published by Elsevier Masson SAS.

3D Numerical Modeling of Pile Group Responses to Excavation-Induced Stress Release in Silty Clay

Directory of Open Access Journals (Sweden)

M. A. Soomro

2018-02-01

Full Text Available Development of underground transportation systems consists of tunnels, basement construction excavations and cut and cover tunnels which may encounter existing pile groups during their construction. Since many previous studies mainly focus on the effects of excavations on single piles, settlement and load transfer mechanism of a pile group subjected to excavation-induced stress release are not well investigated and understood. To address these two issues, three-dimensional coupled-consolidation numerical analysis is conducted by using a hypoplastic model which takes small-strain stiffness into account. A non-linear pile group settlement was induced. This may be attributed to reduction of shaft resistance due to excavation induced stress release, the pile had to settle substantially to further mobilise end-bearing. Compared to the Sp of the pile group, induced settlement of the single pile is larger with similar settlement characteristics. Due to the additional settlement of the pile group, factor of safety for the pile group can be regarded as decreasing from 3.0 to 1.4, based on a displacement-based failure load criterion. Owing to non-uniform stress release, pile group tilted towards the excavation with value of 0.14%. Due to excavation-induced stress release and dragload, head load of rear piles was reduced and transferred to rear piles. This load transfer can increase the axial force in front piles by 94%.

Iron isotope constraints on arsenic release from Mekong Delta sediments, Cambodia

Science.gov (United States)

Matsumoto, T.; Yamaguchi, K. E.; Hirata, T.; Yamagata, Y.; Yamaguchi, A.; Abe, G.

2017-12-01

Arsenic-contaminated groundwater is a world-wide environmental problem and threatens more than 100 million people living in delta areas of South, SE and East Asia. It is typically associated with reducing aquifers with organic-rich alluvial sediments, little thermal gradients, low sulfate concentrations, and slow flushing rates. Such conditions are typical for low-lying countries in Asian deltas; however, compared to Bangladesh, Cambodia has received far less attention. Upon reductive dissolution of Fe-(oxyhydr)oxides that adsorbed As, Fe and As are released into solution as dissolved Fe2+ and arsenate, respectively. Following the oxidation of dissolved Fe2+, newly-formed Fe-(oxyhydr)oxides adsorb As again. Thus, in anoxic waters, concentrations of As correlate with those of dissolved Fe2+. Fluctuating redox conditions in the aquifer are control As release, although inhibition of adsorption of arsenate and arsenite onto the Fe-(oxyhydr)oxides occurs when the concentrations of phosphate, bicarbonate, silicate, and/or organic matter become sufficiently high. Biogeochemical redox reactions of Fe result in significant isotope fractionation (e.g., Johnson et al., 2008). We hypothesized that magnitude of isotope fractionation of Fe in the aquifer sediments, reflecting repeated (incomplete) redox reactions of Fe, may be proportional to the amount of total As release. We aim to calibrate the As release from aquifer sediment by Fe isotope analysis. As a preliminary study, series of sediment samples were collected from the Mekong Delta, Cambodia, in September 2016. Based on measurements by XRF, ICP-AES and ICP-MS, concentrations of As varied significantly covering the range from 4.5 to 15.5 µg/g with a median value of 11 µg/g (higher than the average crustal value of 5 µg/g), and those of Fe is from 2.6 to 9.7 wt.% with a median value of 7.1 wt.%. Concentrations of As and Fe show positive correlation (R2 = 0.72), indicating an effective redox cycling of Fe and As as

Survey of reportable events in nuclear power plants in the Federal Republic of Germany. Period covered: 2nd quarter 1994

International Nuclear Information System (INIS)

1994-01-01

There were 40 reportable events in the period covered. 39 events belonged to the lowest reporting category N (normal notification, INES scale 0), 1 incident belongs to the category E (immediate notification, INES scale 1). There was no release above limit of radioactivity nor were there any effects on man or environment. (orig.) [de

Concept and approaches used in assessing individual and collective doses from releases of radioactive effluents

International Nuclear Information System (INIS)

1988-06-01

To guide on the applications of the principles for limiting radioactive releases contained in Safety Series 77, the Agency is in the process of preparing a number of safety guides. The first one is this present document which deals with the principal aspects of the methods for the assessment of the individual and collective dose. It aims at giving a general guidance to those responsible for establishing programmes for the determination of individual doses as well as collective doses in connection with licensing a site for a nuclear installation. The document is concerned with the principles applied for calculating individual and collective doses from routine releases of radionuclides to the atmosphere and hydrosphere but not releases directly to the geosphere, as in waste management. These areas will be covered by other Agency publications. 75 refs, figs and tabs

Ultrasound-guided plantar fascia release technique: a retrospective study of 46 feet.

Science.gov (United States)

Vohra, Praveen K; Japour, Christopher J

2009-01-01

Ultrasound-guided plantar fascia release offers the surgeon clear visualization of anatomy at the surgical site. This technique uses small arthroscopic dissecting instruments through a 0.5-cm incision, allowing the surgeon to avoid the larger and more tissue-disruptive incision that is traditionally used for plantar heel spur resection and plantar fascia releases. Forty-one patients (46 feet) were selected for the study. The mean patient age was 47 years. Twenty-nine were considered obese with a body mass index greater than 30 kg/m(2). Patients were functionally and subjectively evaluated 4 weeks after surgery using the American Orthopedic Foot and Ankle Society Ankle and Hindfoot Rating Scale. Results from the study show a significant improvement (P = .05 confidence level) 4 weeks postoperatively for the 41 patients (46 feet), compared to their preoperative condition. The mean pretest score was 33.6 (range 10-52); this score improved to 88.0 (range 50-100), 4 weeks postoperatively. There were no postoperative infections or complications. The ultrasound-guided plantar fascia release technique is a practical surgical procedure for the relief of chronic plantar fascia pain because the surgeon is able to clearly visualize the plantar fascia by ultrasound. In addition, there is minimal disruption to surrounding tissue because small instruments are passed through a small 0.5-cm incision. The traditional open method of heel spur surgery, in contrast, uses a larger skin incision of 3 to 5 cm, followed by larger instruments to dissect to the plantar fascia.

Fundamental Study of Disposition and Release of Methane in a Shale Gas Reservoir

Energy Technology Data Exchange (ETDEWEB)

Wang, Yifeng [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Xiong, Yongliang [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Repository Performance; Criscenti, Louise J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geochemistry; Ho, Tuan Ahn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geochemistry; Weck, Philippe F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Storage and Transportation Technology; Ilgen, Anastasia G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geochemistry; Matteo, Edward [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Kruichak, Jessica N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Mills, Melissa M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Nuclear Waste Disposal Research and Analysis; Dewers, Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Geomechanics; Gordon, Margaret E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Dept. of Materials, Devices and Energy Technologies; Akkutlu, Yucel [Texas A & M Univ., College Station, TX (United States). Dept. of Petroleum Engineering

2016-09-01

simulations also indicate that a significant fraction (3 - 35%) of methane deposited in kerogen can potentially become trapped in isolated nanopores and thus not recoverable. We have successfully established experimental capabilities for measuring gas sorption and desorption on shale and model materials under a wide range of physical and chemical conditions. Both low and high pressure measurements show significant sorption of CH₄ and CO₂ onto clays, implying that methane adsorbed on clay minerals could contribute a significant portion of gas-in-place in an unconventional reservoir. We have also studied the potential impact of the interaction of shale with hydrofracking fluid on gas sorption. We have found that the CH₄-CO₂ sorption capacity for the reacted sample is systematically lower (by a factor of ~2) than that for the unreacted (raw) sample. This difference in sorption capacity may result from a mineralogical or surface chemistry change of the shale sample induced by fluid-rock interaction. Our results shed a new light on mechanistic understanding gas release and production decline in unconventional reservoirs.

The initial phase of sudden releases of superheated liquid

International Nuclear Information System (INIS)

Schmidli, J.; Yadigaroglu, G.

1994-01-01

Series of experiments were conducted with refrigerants-114, -12, propane and butane to investigate the initial phase of sudden releases of superheated liquids due to the catastrophic failure of the vessel containing them. The experiments were initiated by shattering spherical flasks of 100 to 2000 ml containing the liquefied, pressurized gases. The variable parameters were the initial superheat, the filling level, the height of the flask above ground, and the relative humidity of the surrounding air. It was found that the initial flashing process is not determined by homogeneous nucleation, but rather by surface instabilities which lead to an evaporation wave traveling from the initial surface towards the center of the released mass. Cloud shape and expansion velocity could be determined from high speed recordings covering the initial stage of the release during which gravity has no influence. When the internal energy was sufficient, it was observed that the expanding droplet/vapor cloud initially propagated spherically with a constant expansion velocity, until Rayleigh-Taylor type instabilities appeared at its surface. Information about the pool which can be formed on the ground, the pressure decay within the flask, the droplet size, and the cloud temperature was collected. The experimental findings for the expansion velocity, as well as for the pool fraction, were the base for a nondimensional analysis leading to correlations which describe the initial phase of such releases and can be used to define the ''source term'' for turbulent dispersion models. (author) 5 figs., 1 tab., 15 refs

Results From Medium Deep Near-UV Imaging With The HST/WFC3 Early Release Science Data

Science.gov (United States)

Cohen, Seth H.; Ryan, R. E., Jr.; Hathi, N. P.; Straughn, A. N.; Yan, H.; Rutkowski, M. J.; Windhorst, R. A.; McCarthy, P. J.; O'Connell, R. W.; Koekemoer, A. M.; SOC, WFC3

2011-01-01

As part of the WFC3 Early Release Science observations, a portion of the GOODS-S field was observed with both the UVIS and IR Channels of the WFC3. The full data set of 100 orbits covers 50 square arcminutes on the sky at 0.09 arcseconds per pixel with ten broad bands covering 0.2-1.7 microns. The field was observed in F225W, F275W, and F336W to 10 sigma point source flux limits of 26.0, 26.1, and 25.7 AB-mag, respectively. In this poster, we will emphasize the results enabled by these UV observations of faint galaxies. We demonstrate that these UV observations are extremely useful, even for galaxies of intermediate redshifts (zdropout galaxies, AGN, etc. In particular, optical and near-IR studies only measure the rest-frame UV properties of the highest redshift galaxies, and for comparison these UV observations are needed to properly study galaxy evolution near the peak of the global star formation rate density. In fact, deeper UV observations, below the atmospheric cutoff, and with space-based resolution, are need to properly study galaxies at the faint-end of the luminosity function at z 1. This paper is based on Early Release Science observations made by the WFC3 Scientific Oversight Committee. We are grateful to the Director of the Space Telescope Science Institute for awarding Director's Discretionary time for this program. Support for program #11359 was provided by NASA through a grant from the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, Inc., under NASA contract NAS 5-26555.

A Randomized, Single-Blind, Substitution Study of OROS Methylphenidate (Concerta) in ADHD Adults Receiving Immediate Release Methylphenidate

Science.gov (United States)

Spencer, Thomas J.; Mick, Eric; Surman, Craig B. H.; Hammerness, Paul; Doyle, Robert; Aleardi, Megan; Kotarski, Meghan; Williams, Courtney G.; Biederman, Joseph

2011-01-01

Objective: The main aim of this study was to examine the efficacy, tolerability, and compliance of an extended-release formulation of methylphenidate (OROS-MPH) in adults with ADHD receiving immediate-release methylphenidate (IR-MPH). Method: Participants were outpatient adults with ADHD who were stable on IR-MPH-administered TID. Participants…

Reactor cover gas monitoring at the Fast Flux Test Facility

Energy Technology Data Exchange (ETDEWEB)

Bechtold, R A; Holt, F E; Meadows, G E; Schenter, R E [Westinghouse Hanford Company, Richland, WA (United States)

1987-07-01

The Fast Flux Test Facility (FFTF) is a 400 megawatt (thermal) sodium cooled reactor designed for irradiation testing of fuels, materials and components for LMRs. It is operated by the Westinghouse Hanford Company for the U. S. Department of Energy on the government-owned Hanford reservation near Richland, Washington. The first 100 day operating cycle began in April 1982 and the eighth operating cycle was completed In July 1986. Argon is used as the cover gas for all sodium systems at the plant. A program for cover gas monitoring has been in effect since the start of sodium fill in 1978. The argon is supplied to the FFTF by a liquid argon Dewar System and used without further purification. A liquid argon Dewar system provides the large volume of inert gas required for operation of the FFTF. The gas is used as received and is not recycled. Low concentrations of krypton and xenon in the argon supply are essential to preclude interference with the gas tag system. Gas chromatography has been valuable for detection of inadvertent air in leakage during refueling operations. A temporary system is installed over the reactor during outages to prevent oxide formation in the sodium vapor traps upstream from the on line gas chromatograph. On line gas monitoring by gamma spectrometry and grab sampling with GTSTs has been successful for the identification of numerous radioactive gas releases from creep capsule experiments as well as 9 fuel pin ruptures. A redundant fission gas monitoring system has been installed to insure constant surveillance of the reactor cover gas.

Release study of diclofenac from new carbomer gels.

Science.gov (United States)

Bregni, Carlos; Chiappetta, Diego; Faiden, Natalia; Carlucci, Adriana; García, Roberto; Pasquali, Ricardoc

2008-01-01

Carbopol gels were prepared using a traditional polymer with mucoadhesive properties (974P). A new Carbomer derivative Ultrez 21 was also evaluated. Mineral oil, as occlusive ingredient, glycerol as humectant and ethanol were included in all the compositions. The feasibility of preparing these formulations with or without a bioadhesive polymer (Polycarbophil AA-1) and a second oil phase with enhancer activity (Miglyol 840) was evaluated. Further characterization including physical stability during a year was carried out. In vitro release behaviour of diclofenac sodium in Franz diffusion cell was evaluated with some selected formulations using an ethanol-water (50% w/w) solution as receptor medium. Addition of Polycarbophil AA-1 increased formulation viscosity and decreased drug release. These types of topical dosage forms could give sustained delivery of drug onto the skin, could tolerate the incorporation of an enhancer, a humectant and an occlusive phase, so they are interesting promises to improve skin absorption of nonsteroidal anti-inflammatory drugs and to prevent side effects associated.

Experimental study and simulation of mass distribution of the covering layer of soybean seeds coated in a spouted bed

Directory of Open Access Journals (Sweden)

Duarte C. R.

2004-01-01

Full Text Available In previous work, it was observed that the covering of soybean seeds with bacteria and micronutrients enhances vigorous growth of the plant thereby avoiding use of ammoniacal fertilizers. In the spouted bed covering can be done by pulverization of the coater slurry on the soybean seeds using a pneumatic atomizer. The optimum thickness of the cover allows the fundamental gaseous interchanges for germination and provides the ideal conditions for bacterium activity. The objective of this work was to study the influence of the process variables on thickness of the cover. A simulation of the mass distribution of seeds was obtained using a population balance model. Through the results obtained the operational conditions under which the coating layer distribution were determined has the greatest uniformity.

77 FR 48733 - Transitional Program for Covered Business Method Patents-Definitions of Covered Business Method...

Science.gov (United States)

2012-08-14

... Office 37 CFR Part 42 Transitional Program for Covered Business Method Patents--Definitions of Covered... Business Method Patents-- Definitions of Covered Business Method Patent and Technological Invention AGENCY... forth in detail the definitions of the terms ``covered business method patent'' and ``technological...

A statistical model for deriving probability distributions of contamination for accidental releases

International Nuclear Information System (INIS)

ApSimon, H.M.; Davison, A.C.

1986-01-01

Results generated from a detailed long-range transport model, MESOS, simulating dispersal of a large number of hypothetical releases of radionuclides in a variety of meteorological situations over Western Europe have been used to derive a simpler statistical model, MESOSTAT. This model may be used to generate probability distributions of different levels of contamination at a receptor point 100-1000 km or so from the source (for example, across a frontier in another country) without considering individual release and dispersal scenarios. The model is embodied in a series of equations involving parameters which are determined from such factors as distance between source and receptor, nuclide decay and deposition characteristics, release duration, and geostrophic windrose at the source. Suitable geostrophic windrose data have been derived for source locations covering Western Europe. Special attention has been paid to the relatively improbable extreme values of contamination at the top end of the distribution. The MESOSTAT model and its development are described, with illustrations of its use and comparison with the original more detailed modelling techniques. (author)

Development of a Risk-Based Probabilistic Performance-Assessment Method for Long-Term Cover Systems - 2nd Edition

International Nuclear Information System (INIS)

HO, CLIFFORD K.; ARNOLD, BILL W.; COCHRAN, JOHN R.; TAIRA, RANDAL Y.

2002-01-01

A probabilistic, risk-based performance-assessment methodology has been developed to assist designers, regulators, and stakeholders in the selection, design, and monitoring of long-term covers for contaminated subsurface sites. This report describes the method, the software tools that were developed, and an example that illustrates the probabilistic performance-assessment method using a repository site in Monticello, Utah. At the Monticello site, a long-term cover system is being used to isolate long-lived uranium mill tailings from the biosphere. Computer models were developed to simulate relevant features, events, and processes that include water flux through the cover, source-term release, vadose-zone transport, saturated-zone transport, gas transport, and exposure pathways. The component models were then integrated into a total-system performance-assessment model, and uncertainty distributions of important input parameters were constructed and sampled in a stochastic Monte Carlo analysis. Multiple realizations were simulated using the integrated model to produce cumulative distribution functions of the performance metrics, which were used to assess cover performance for both present- and long-term future conditions. Performance metrics for this study included the water percolation reaching the uranium mill tailings, radon gas flux at the surface, groundwater concentrations, and dose. Results from uncertainty analyses, sensitivity analyses, and alternative design comparisons are presented for each of the performance metrics. The benefits from this methodology include a quantification of uncertainty, the identification of parameters most important to performance (to prioritize site characterization and monitoring activities), and the ability to compare alternative designs using probabilistic evaluations of performance (for cost savings)

QSPR Study of the Retention/release Property of Odorant Molecules in Water Using Statistical Methods

Directory of Open Access Journals (Sweden)

Assia Belhassan

2017-10-01

Full Text Available An integrated approach physicochemistry and structures property relationships has been carried out to study the odorant molecules retention/release phenomenon in the water. This study aimed to identify the molecular properties (molecular descriptors that govern this phenomenon assuming that modifying the structure leads automatically to a change in the retention/release property of odorant molecules. ACD/ChemSketch, MarvinSketch, and ChemOffice programs were used to calculate several molecular descriptors of 51 odorant molecules (15 alcohols, 11 aldehydes, 9 ketones and 16 esters. A total of 37 molecules (2/3 of the data set were placed in the training set to build the QSPR models, whereas the remaining, 14 molecules (1/3 of the data set constitute the test set. The best descriptors were selected to establish the quantitative structure property relationship (QSPR of the retention/release property of odorant molecules in water using multiple linear regression (MLR, multiple non-linear regression (MNLR and an artificial neural network (ANN methods. We propose a quantitative model according to these analyses. The models were used to predict the retention/release property of the test set compounds, and agreement between the experimental and predicted values was verified. The descriptors showed by QSPR study are used for study and designing of new compounds. The statistical results indicate that the predicted values are in good agreement with the experimental results. To validate the predictive power of the resulting models, external validation multiple correlation coefficient was calculated and has both in addition to a performant prediction power, a favorable estimation of stability. DOI: http://dx.doi.org/10.17807/orbital.v9i4.978 

Sensitivity studies on parameters affecting gas release from an underground rock cavern

International Nuclear Information System (INIS)

Schlueter, E.; Pruess, K.

1990-01-01

A series of numerical simulation experiments is performed to quantify the effects of the release and migration of non-condensible gas in water-saturated fractured rock formations. The relative importance of multiphase parameters such as relative permeability, capillary pressure, intrinsic permeability, and porosity on system behavior is studied. 10 refs., 28 figs., 5 tabs

In vitro studies of copper release from powder particles in synthetic biological media

International Nuclear Information System (INIS)

Midander, Klara; Wallinder, Inger Odnevall; Leygraf, Christofer

2007-01-01

The aim of this paper is to provide quantitative data on copper release from powder particles of different copper materials, including artificial copper patina, Cu 2 O and metallic Cu, when exposed to different synthetic biological media to simulate an inhalation scenario and/or skin contact. Generated data may contribute in risk assessment of potential health effects following exposure to and handling of various copper materials. All tests were performed in vitro to determine total copper concentrations, release rates of total copper, and to elucidate its time-dependence. The copper release process was interpreted in terms of specific surface area, surface morphology-, and composition. All powder materials show a time-dependent release process with total copper release rates less than 3 μg/cm 2 per hour at steady state conditions, for all media investigated. The importance of using relevant test media when simulating different interstitial lung conditions and difficulties encountered when comparing powder particles of essentially different properties are thoroughly discussed. - Copper release rates from particles are essential to assess potential health aspects

A Comparative Study on the Lot Release Systems for Vaccines as of 2016.

Science.gov (United States)

Fujita, Kentaro; Naito, Seishiro; Ochiai, Masaki; Konda, Toshifumi; Kato, Atsushi

2017-09-25

Many countries have already established their own vaccine lot release system that is designed for each country's situation: while the World Health Organization promotes for the convergence of these regulatory systems so that vaccines of assured quality are provided globally. We conducted a questionnaire-based investigation of the lot release systems for vaccines in 7 countries and 2 regions. We found that a review of the summary protocol by the National Regulatory Authorities was commonly applied for the independent lot release of vaccines, however, we also noted some diversity between countries, especially in regard to the testing policy. Some countries and regions, including Japan, regularly tested every lot of vaccines, whereas the frequency of these tests was reduced in other countries and regions as determined based on the risk assessment of these products. Test items selected for the lot release varied among the countries or regions investigated, although there was a tendency to prioritize the potency tests. An understanding of the lot release policy may contribute to improving and harmonizing the lot release system globally in the future.

Study on mechanics of driving drum with superelastic convexity surface covering-layer structure

Energy Technology Data Exchange (ETDEWEB)

Xiao, L.J.; Sui, X.H.; Miao, D.J. [Shandong University of Science & Technology, Qingdao (China)

2008-09-15

Belt conveyor is one of the main transport equipment in coal mine and the driving drum is its key part. With the method of bionic design, the mushroom morphological structure is applied to the design of covering-layer structure of driving drum surface of belt conveyor. Superelastic rubber with large deformation is adopted as the covering-layer material. Nonlinear constitutive model of rubber, which is of superelasticity and large deformation, is established. The stress states and deformation principles of driving drums including both bionic covering-layer and common covering-layer are obtained by static intensity analysis with Finite Element Analysis (FEA) software ANSYS. The values of the stress and strain on the driving drum surface are gotten and the dangerous area is determined. FEA results show that the superelastic convexity surface structure can enlarge the contact area between the driving drum and viscoelastic belt. The results also show that in comparison with common driving drum, the bionic surface driving drum can not only increase the friction coefficient between drum and belt but also prolong its service life.

Covered by lines and Conic connected varieties

Directory of Open Access Journals (Sweden)

Alex Massarenti

2011-12-01

Full Text Available We study some properties of an embedded variety covered by lines and give a numerical criterion ensuring the existence of a singular conic through two of its general points. We show that our criterion is sharp. Conic-connected, covered by lines, QEL, LQEL, prime Fano, defective, and dual defective varieties are closely related. We study some relations between the above mentioned classes of objects using basic results by Ein and Zak.

Minimum forest cover required for sustainable water flow regulation of a watershed: a case study in Jambi Province, Indonesia

Directory of Open Access Journals (Sweden)

S. Tarigan

2018-01-01

Full Text Available In many tropical regions, the rapid expansion of monoculture plantations has led to a sharp decline in forest cover, potentially degrading the ability of watersheds to regulate water flow. Therefore, regional planners need to determine the minimum proportion of forest cover that is required to support adequate ecosystem services in these watersheds. However, to date, there has been little research on this issue, particularly in tropical areas where monoculture plantations are expanding at an alarming rate. Therefore, in this study, we investigated the influence of forest cover and oil palm (Elaeis guineensis and rubber (Hevea brasiliensis plantations on the partitioning of rainfall into direct runoff and subsurface flow in a humid, tropical watershed in Jambi Province, Indonesia. To do this, we simulated streamflow with a calibrated Soil and Water Assessment Tool (SWAT model and observed several watersheds to derive the direct runoff coefficient (C and baseflow index (BFI. The model had a strong performance, with Nash–Sutcliffe efficiency values of 0.80–0.88 (calibration and 0.80–0.85 (validation and percent bias values of −2.9–1.2 (calibration and 7.0–11.9 (validation. We found that the percentage of forest cover in a watershed was significantly negatively correlated with C and significantly positively correlated with BFI, whereas the rubber and oil palm plantation cover showed the opposite pattern. Our findings also suggested that at least 30 % of the forest cover was required in the study area for sustainable ecosystem services. This study provides new adjusted crop parameter values for monoculture plantations, particularly those that control surface runoff and baseflow processes, and it also describes the quantitative association between forest cover and flow indicators in a watershed, which will help regional planners in determining the minimum proportion of forest and the maximum proportion of plantation to ensure that a

Studies for improvement of regulatory control on the radioactive effluent released from nuclear facilities

International Nuclear Information System (INIS)

Cheong, Jae Hak; Park, H. M.; Song, M. C.; Lee, K. H.; Jang, J. K.; Chun, J. K.; Jeong, K. H.

2005-05-01

This report contains the second-year results of the research project titled 'Studies for Improvement of Regulatory Control on the Radioactive Effluent Released from Nuclear Facilities' and mainly provides technical and strategic approaches to improve performance of regulatory control on the gaseous effluent released from domestic nuclear facilities. The main result contained here includes overview and technical bases of radioactive gaseous effluent control (Chapter 1), reconsideration of the sensitivity requirements for measurement of radioactivity in gaseous effluent sample (Chapter 2), uncertainty analysis of the calculated radioactivity in gaseous effluent (Chapter 3), and improvement of quantification method of noble gas releases (Chapter 4). In addition, analysis of the impact due to combined sampling of particulate from multiple release points (Chapter 5), comparison of domestic nuclear reactors gaseous effluent data to foreign PWRs (Chapter 6), standardized sampling technique for collection of gaseous tritium (Chapter 7), and application of Xe-133 equivalent concept to gaseous effluent control (Chapter 8) are also provided. As a whole, this report provides a generic approach to improve the performance of regulatory control on the gaseous effluent. Therefore, actual enforcement of the recommendations should be preceded by establishment of a series of action plans reflecting on the site- and facility-specific design and operational features

Southern Hemisphere origins for interannual variations of Tibetan Plateau snow cover in boreal summer

Science.gov (United States)

Wu, Z.

2017-12-01

The climate response to the Tibetan Plateau (TP) snow cover (TPSC) has been receiving extensive concern. However, relatively few studies have devoted to revealing the potential factors that can contribute to the TPSC variability on the interannual time scale. Especially during the boreal summer, snow cover can persist over the TP at high elevations, which exerts profound influences on the local and remote climate change. The present study finds that May Southern Hemisphere (SH) annular mode (SAM), the dominating mode of atmospheric circulation variability in the SH extratropics, exhibits a significant positive relationship with the boreal summer TPSC interannual variability. Observational analysis and numerical experiments manifest that the signal of May SAM can be "prolonged" by a meridional Indian Ocean tripole (IOT) sea surface temperature anomaly (SSTA) via atmosphere-ocean interaction. The IOT SSTA pattern persists into the following summer and excites anomalous local-scale zonal vertical circulation. Subsequently, a positive (or negative) tropical dipole rainfall (TDR) mode is induced with deficient (or sufficient) precipitation in tropical western Indian Ocean and sufficient (or deficient) precipitation in eastern Indian Ocean-Maritime continent. Rossby wave source diagnosis reveals that the wave energies, generated by the latent heat release of the TDR mode, propagate northward into western TP. As a response, abnormal cyclonic circulation and upward movement are triggered and prevail over western TP, providing favorable dynamical conditions for more TPSC, and vice versa. Hence, the IOT SSTA plays an "ocean bridge" role and the TDR mode acts as an "atmosphere bridge" role in the process of May SAM impacting the following summer TPSC variability. The results of our work may provide new insight about the cross-equatorial propagation of the SAM influence. Keywords Southern Hemisphere annular mode; Tibetan Plateau snow cover; Rossby wave source

Covering folded shapes

Directory of Open Access Journals (Sweden)

Oswin Aichholzer

2014-05-01

Full Text Available Can folding a piece of paper flat make it larger? We explore whether a shape S must be scaled to cover a flat-folded copy of itself. We consider both single folds and arbitrary folds (continuous piecewise isometries \\(S\\to\\mathbb{R}^2\\. The underlying problem is motivated by computational origami, and is related to other covering and fixturing problems, such as Lebesgue's universal cover problem and force closure grasps. In addition to considering special shapes (squares, equilateral triangles, polygons and disks, we give upper and lower bounds on scale factors for single folds of convex objects and arbitrary folds of simply connected objects.

Techniques for Reaeration of Hydropower Releases.

Science.gov (United States)

1983-02-01

release improvement. However, selected reservoir aeration studies not conducted primarily for improving hydroturbine releases but which have application...for hydroturbine release reaeration were also reviewed. Because oxygen transfer mechanisms are vitally important to the development of more efficient...the key words turbine aeration, turbine vent, turbine I’ aspiration, hydroturbine aeration, tailrace aeration, draft tube vent, and vacuum breaker. A

Modelling vesicular release at hippocampal synapses.

Directory of Open Access Journals (Sweden)

Suhita Nadkarni

2010-11-01

Full Text Available We study local calcium dynamics leading to a vesicle fusion in a stochastic, and spatially explicit, biophysical model of the CA3-CA1 presynaptic bouton. The kinetic model for vesicle release has two calcium sensors, a sensor for fast synchronous release that lasts a few tens of milliseconds and a separate sensor for slow asynchronous release that lasts a few hundred milliseconds. A wide range of data can be accounted for consistently only when a refractory period lasting a few milliseconds between releases is included. The inclusion of a second sensor for asynchronous release with a slow unbinding site, and thereby a long memory, affects short-term plasticity by facilitating release. Our simulations also reveal a third time scale of vesicle release that is correlated with the stimulus and is distinct from the fast and the slow releases. In these detailed Monte Carlo simulations all three time scales of vesicle release are insensitive to the spatial details of the synaptic ultrastructure. Furthermore, our simulations allow us to identify features of synaptic transmission that are universal and those that are modulated by structure.

A high temperature heating device for the study of fission product release from nuclear fuel

International Nuclear Information System (INIS)

Svedkauskaite-Le Gore, Jolanta; Kivel, Niko; Guenther-Leopold, Ines

2010-01-01

At the Paul Scherrer Institute a high temperature inductive heating furnace, which can heat fuel samples up to 2300 deg. C, has been developed in order to study the release of fission products. The furnace can be directly connected to an inductively coupled plasma mass spectrometer for online monitoring of the released elements and does not require their trapping before measurement. This paper describes the design of the inductive heating furnace, discusses its operating parameters, limitations and illustrates foreseen applications. (authors)

Pharmaceutical Product Lead Optimization for Better In vivo Bioequivalence Performance: A case study of Diclofenac Sodium Extended Release Matrix Tablets.

Science.gov (United States)

Shahiwala, Aliasgar; Zarar, Aisha

2018-01-01

In order to prove the validity of a new formulation, a considerable amount of effort is required to study bioequivalence, which not only increases the burden of carrying out a number of bioequivalence studies but also eventually increases the cost of the optimization process. The aim of the present study was to develop sustained release matrix tablets containing diclofenac sodium using natural polymers and to demonstrate step by step process of product development till the prediction of in vivo marketed product equivalence of the developed product. Different batches of tablets were prepared by direct compression. In vitro drug release studies were performed as per USP. The drug release data were assessed using model-dependent, modelindependent and convolution approaches. Drug release profiles showed that extended release action were in the following order: Gum Tragacanth > Sodium Alginate > Gum Acacia. Amongst the different batches prepared, only F1 and F8 passed the USP criteria of drug release. Developed formulas were found to fit Higuchi kinetics model with Fickian (case I) diffusion-mediated release mechanism. Model- independent kinetics confirmed that total of four batches were passed depending on the similarity factors based on the comparison with the marketed Diclofenac. The results of in vivo predictive convolution model indicated that predicted AUC, Cmax and Tmax values for batch F8 were similar to that of marketed product. This study provides simple yet effective outline of pharmaceutical product development process that will minimize the formulation development trials and maximize the product success in bioequivalence studies. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

Inhibition of basophil histamine release by gangliosides. Further studies on the significance of cell membrane sialic acid in the histamine release process

DEFF Research Database (Denmark)

Jensen, C; Norn, S; Thastrup, Ole

1987-01-01

with the glucolipid mixture increased the sialic acid content of the cells, and this increase was attributed to an insertion of gangliosides into the cell membrane. The inhibition of histamine release was abolished by increasing the calcium concentration, which substantiates our previous findings that cell membrane......Histamine release from human basophils was inhibited by preincubation of the cells with a glucolipid mixture containing sialic acid-containing gangliosides. This was true for histamine release induced by anti-IgE, Concanavalin A and the calcium ionophore A23187, whereas the release induced by S....... aureus Wood 46 was not affected. It was demonstrated that the inhibitory capacity of the glucolipid mixture could be attributed to the content of gangliosides, since no inhibition was obtained with cerebrosides or with gangliosides from which sialic acid was removed. Preincubation of the cells...

Sodium spray release accident analysis for fast reactor safety studies

International Nuclear Information System (INIS)

Shire, P.R.

1976-10-01

A computer code has been developed to model the effects of postulated sodium spray release from LMFBR piping. The calculation method utilizes gas convection and droplet combustion theory to calculate the pressure and temperature effects in a range of 0 to 21% oxygen. Droplet motion and large aggregate sodium surface area result in rapid release of combustion and sensible heat causing a nearly adiabtic pressure pulse peaking in a matter of seconds. This analytical tool has indicated good agreement with prototypic test data for a range of oxygen concentrations, cell volumes and droplet sizes

Forest cover change and fragmentation using Landsat data in Maçka State Forest Enterprise in Turkey.

Science.gov (United States)

Cakir, Günay; Sivrikaya, Fatih; Keleş, Sedat

2008-02-01

Monitoring forest cover change and understanding the dynamic of forest cover is increasingly important in sustainable development and management of forest ecosystems. This paper uses remote sensing (RS) techniques to monitor forest cover change in Maçka State Forest Enterprise (MSFE) located in NE of Turkey through 1975 to 2000 and then analyses spatial and temporal changes in forest cover by Geographical Information Systems (GIS) and FRAGSTATStrade mark. Forest cover changes were detected from a time series of satellite images of Landsat MSS in 1975, Landsat TM in 1987, and Landsat ETM+ in 2000 using RS and GIS. The results showed that total forest area, productive forest area and degraded forest area increased while broadleaf forest area and non forest area decreased. Mixed forest and degraded forest increased during the first (1975-1987) period, but decreased during the second (1987-2000) period. During the whole study period, the annual forestation rate was 152 ha year(-1), equivalent to 0.27% year(-1) using the compound-interest-rate formula. The total number of patches increased from 36,204 to 48,092 (33%), and mean size of forest patch (MPS) decreased from 2.8 ha to 2.1 ha during a 25 year period. Number of smaller patches (patches in 0-100 ha size class) increased, indicating more fragmented landscape over time that might create a risk for the maintenance of biodiversity of the area. While total population increased from 1975 to 2000 (3.7%), rural population constantly decreased. The increase of forest areas may well be explained by the fact that demographic movement of rural areas concentrated into Maçka City Center. These figures also indicated that decrease in the rural population might likely lead to the release of human pressure to forest areas, probably resulting in a positive development of forest areas.

Tracing Atlantic Water Signature in the Arctic Sea Ice Cover East of Svalbard

Directory of Open Access Journals (Sweden)

Vladimir V. Ivanov

2012-01-01

Full Text Available We focus on the Arctic Ocean between Svalbard and Franz Joseph Land in order to elucidate the possible role of Atlantic water (AW inflow in shaping ice conditions. Ice conditions substantially affect the temperature regime of the Spitsbergen archipelago, particularly in winter. We test the hypothesis that intensive vertical mixing at the upper AW boundary releases substantial heat upwards that eventually reaches the under-ice water layer, thinning the ice cover. We examine spatial and temporal variation of ice concentration against time series of wind, air temperature, and AW temperature. Analysis of 1979–2011 ice properties revealed a general tendency of decreasing ice concentration that commenced after the mid-1990s. AW temperature time series in Fram Strait feature a monotonic increase after the mid-1990s, consistent with shrinking ice cover. Ice thins due to increased sensible heat flux from AW; ice erosion from below allows wind and local currents to more effectively break ice. The winter spatial pattern of sea ice concentration is collocated with patterns of surface heat flux anomalies. Winter minimum sea ice thickness occurs in the ice pack interior above the AW path, clearly indicating AW influence on ice thickness. Our study indicates that in the AW inflow region heat flux from the ocean reduces the ice thickness.

Study of BSA protein adsorption/release on hydroxyapatite nanoparticles

Science.gov (United States)

Swain, Sanjaya Kumar; Sarkar, Debasish

2013-12-01

Three different spherical, rod and fibrous morphologies of hydroxyapatite (HA) nanoparticles have been prepared through control over the processing parameters like temperature, pH and Ca:P ratio. Protein adsorption/release with respect to HA nanoparticle morphologies are investigated using model protein bovine serum albumin (BSA). BSA adsorption on HA nanoparticles follows Langmuir adsorption isotherm. Thermal analysis and FT-IR spectrum confirms the BSA adhesion and retention of their secondary structure. High surface area with high Ca:P ratio nanorod adsorbs relatively more amount (28 mg BSA/gm of nanorod HA) of BSA within 48 h in comparison with counterpart fibroid and spherical morphologies. Slow and steady BSA release (75 wt% of adsorbed BSA in 96 h) from nanorod HA is found as futuristic drug delivery media.

Gross and net land cover changes in the main plant functional types derived from the annual ESA CCI land cover maps (1992-2015)

Science.gov (United States)

Li, Wei; MacBean, Natasha; Ciais, Philippe; Defourny, Pierre; Lamarche, Céline; Bontemps, Sophie; Houghton, Richard A.; Peng, Shushi

2018-01-01

Land-use and land-cover change (LULCC) impacts local energy and water balance and contributes on global scale to a net carbon emission to the atmosphere. The newly released annual ESA CCI (climate change initiative) land cover maps provide continuous land cover changes at 300 m resolution from 1992 to 2015, and can be used in land surface models (LSMs) to simulate LULCC effects on carbon stocks and on surface energy budgets. Here we investigate the absolute areas and gross and net changes in different plant functional types (PFTs) derived from ESA CCI products. The results are compared with other datasets. Global areas of forest, cropland and grassland PFTs from ESA are 30.4, 19.3 and 35.7 million km2 in the year 2000. The global forest area is lower than that from LUH2v2h (Hurtt et al., 2011), Hansen et al. (2013) or Houghton and Nassikas (2017) while cropland area is higher than LUH2v2h (Hurtt et al., 2011), in which cropland area is from HYDE 3.2 (Klein Goldewijk et al., 2016). Gross forest loss and gain during 1992-2015 are 1.5 and 0.9 million km2 respectively, resulting in a net forest loss of 0.6 million km2, mainly occurring in South and Central America. The magnitudes of gross changes in forest, cropland and grassland PFTs in the ESA CCI are smaller than those in other datasets. The magnitude of global net cropland gain for the whole period is consistent with HYDE 3.2 (Klein Goldewijk et al., 2016), but most of the increases happened before 2004 in ESA and after 2007 in HYDE 3.2. Brazil, Bolivia and Indonesia are the countries with the largest net forest loss from 1992 to 2015, and the decreased areas are generally consistent with those from Hansen et al. (2013) based on Landsat 30 m resolution images. Despite discrepancies compared to other datasets, and uncertainties in converting into PFTs, the new ESA CCI products provide the first detailed long-term time series of land-cover change and can be implemented in LSMs to characterize recent carbon dynamics

Armored Geomembrane Cover Engineering

Directory of Open Access Journals (Sweden)

Kevin Foye

2011-06-01

Full Text Available Geomembranes are an important component of modern engineered barriers to prevent the infiltration of stormwater and runoff into contaminated soil and rock as well as waste containment facilities—a function generally described as a geomembrane cover. This paper presents a case history involving a novel implementation of a geomembrane cover system. Due to this novelty, the design engineers needed to assemble from disparate sources the design criteria for the engineering of the cover. This paper discusses the design methodologies assembled by the engineering team. This information will aid engineers designing similar cover systems as well as environmental and public health professionals selecting site improvements that involve infiltration barriers.

The Multimedia Environmental Pollutant Assessment System (MEPAS)reg-sign: Source-term release formulations

International Nuclear Information System (INIS)

Streile, G.P.; Shields, K.D.; Stroh, J.L.; Bagaasen, L.M.; Whelan, G.; McDonald, J.P.; Droppo, J.G.; Buck, J.W.

1996-11-01

This report is one of a series of reports that document the mathematical models in the Multimedia Environmental Pollutant Assessment System (MEPAS). Developed by Pacific Northwest National Laboratory for the US Department of Energy, MEPAS is an integrated impact assessment software implementation of physics-based fate and transport models in air, soil, and water media. Outputs are estimates of exposures and health risk assessments for radioactive and hazardous pollutants. Each of the MEPAS formulation documents covers a major MEPAS component such as source-term, atmospheric, vadose zone/groundwater, surface water, and health exposure/health impact assessment. Other MEPAS documentation reports cover the sensitivity/uncertainty formulations and the database parameter constituent property estimation methods. The pollutant source-term release component is documented in this report. MEPAS simulates the release of contaminants from a source, transport through the air, groundwater, surface water, or overland pathways, and transfer through food chains and exposure pathways to the exposed individual or population. For human health impacts, risks are computed for carcinogens and hazard quotients for noncarcinogens. MEPAS is implemented on a desktop computer with a user-friendly interface that allows the user to define the problem, input the required data, and execute the appropriate models for both deterministic and probabilistic analyses

Finite cover method with mortar elements for elastoplasticity problems

Science.gov (United States)

Kurumatani, M.; Terada, K.

2005-06-01

Finite cover method (FCM) is extended to elastoplasticity problems. The FCM, which was originally developed under the name of manifold method, has recently been recognized as one of the generalized versions of finite element methods (FEM). Since the mesh for the FCM can be regular and squared regardless of the geometry of structures to be analyzed, structural analysts are released from a burdensome task of generating meshes conforming to physical boundaries. Numerical experiments are carried out to assess the performance of the FCM with such discretization in elastoplasticity problems. Particularly to achieve this accurately, the so-called mortar elements are introduced to impose displacement boundary conditions on the essential boundaries, and displacement compatibility conditions on material interfaces of two-phase materials or on joint surfaces between mutually incompatible meshes. The validity of the mortar approximation is also demonstrated in the elastic-plastic FCM.

Heat release effects on mixing scales of non-premixed turbulent wall-jets: A direct numerical simulation study

International Nuclear Information System (INIS)

Pouransari, Zeinab; Vervisch, Luc; Johansson, Arne V.

2013-01-01

Highlights: ► A non-premixed turbulent flame close to a solid surface is studied using DNS. ► Heat release effects delay transition and enlarge fluctuation of density and pressure. ► The fine-scale structures damped and surface wrinkling diminished due to heat-release. ► Using semilocal scaling improves the collapse of turbulence statistic in inner region. ► There are regions of the flame where considerable (up to 10%) premixed burning occurs. -- Abstract: The present study concerns the role of heat release effects on characteristics mixing scales of turbulence in reacting wall-jet flows. Direct numerical simulations of exothermic reacting turbulent wall-jets are performed and compared to the isothermal reacting case. An evaluation of the heat-release effects on the structure of turbulence is given by examining the mixture fraction surface characteristics, diagnosing vortices and exploring the dissipation rate of the fuel and passive scalar concentrations, and moreover by illustration of probability density functions of reacting species and scatter plots of the local temperature against the mixture fraction. Primarily, heat release effects delay the transition, enlarge the fluctuation intensities of density and pressure and also enhance the fluctuation level of the species concentrations. However, it has a damping effect on all velocity fluctuation intensities and the Reynolds shear stress. A key result is that the fine-scale structures of turbulence are damped, the surface wrinkling is diminished and the vortices become larger due to heat-release effects. Taking into account the varying density by using semi-local scaling improves the collapse of the turbulence statistics in the inner region, but does not eliminate heat release induced differences in the outer region. Examining the two-dimensional premultiplied spanwise spectra of the streamwise velocity fluctuations indicates a shifting in the positions of the outer peaks, associated with large

Monitoring the Variation in Ice-Cover Characteristics of the Slave River, Canada Using RADARSAT-2 Data—A Case Study

Directory of Open Access Journals (Sweden)

Thuan Chu

2015-10-01

Full Text Available The winter regime of river-ice covers in high northern latitude regions is often a determining factor in the management of water resources, conservation of aquatic ecosystems and preservation of traditional and cultural lifestyles of local peoples. As ground-based monitoring of river-ice regimes in high northern latitudes is expensive and restricted to a few locations due to limited accessibility to most places along rivers from shorelines, remote sensing techniques are a suitable approach for monitoring. This study developed a RADARSAT-2 based method to monitor the spatio-temporal variation of ice covers, as well as ice types during the freeze-up period, along the main channel of the Slave River Delta in the Northwest Territories of Canada. The spatio-temporal variation of ice covers along the river was analyzed using the backscatter-based coefficient of variation (CV in the 2013–2014 and 2014–2015 winters. As a consequence of weather and flow conditions, the ice cover in the 2013–2014 winter had the higher variation than the 2014–2015 winter, particularly in the potential areas of flooded/cracked ice covers. The river sections near active channels (e.g., Middle Channel and Nagle Channel, Big Eddy, and Great Slave Lake also yielded higher intra-annual variation of ice cover characteristics during the winters. With the inclusion of backscatter and texture analysis from RADARSAT-2 data, four water and ice cover classes consisting of open water, thermal ice, juxtaposed ice, and consolidated ice, were discriminated in the images acquired between November and March in both the studied winters. In addition to river geomorphology and climatic conditions such as river width, sinuosity or air temperature, the fluctuation of water flows during the winter has a significant impact on the variation of ice cover as well as the formation of different ice types in the Slave River. The RADARSAT-2 based monitoring algorithm can also be applied to other

Development of a Risk-Based Performance Assessment Method for Long-Term Cover Systems--Application to the Monticello Mill Tailings Repository

International Nuclear Information System (INIS)

HO, CLIFFORD K.; ARNOLD, BILL W.; COCHRAN, JOHN R.; WEBB, STEPHEN W.; TAIRA, RANDAL Y.

2001-01-01

A probabilistic, risk-based performance-assessment methodology is being developed to assist designers, regulators, and involved stakeholders in the selection, design, and monitoring of long-term covers for contaminated subsurface sites. This report presents an example of the risk-based performance-assessment method using a repository site in Monticello, Utah. At the Monticello site, a long-term cover system is being used to isolate long-lived uranium mill tailings from the biosphere. Computer models were developed to simulate relevant features, events, and processes that include water flux through the cover, source-term release, vadose-zone transport, saturated-zone transport, gas transport, and exposure pathways. The component models were then integrated into a total-system performance-assessment model, and uncertainty distributions of important input parameters were constructed and sampled in a stochastic Monte Carlo analysis. Multiple realizations were simulated using the integrated model to produce cumulative distribution functions of the performance metrics, which were used to assess cover performance for both present- and long-term future conditions. Performance metrics for this study included the water percolation reaching the uranium mill tailings, radon flux at the surface, groundwater concentrations, and dose. Results of this study can be used to identify engineering and environmental parameters (e.g., liner properties, long-term precipitation, distribution coefficients) that require additional data to reduce uncertainty in the calculations and improve confidence in the model predictions. These results can also be used to evaluate alternative engineering designs and to identify parameters most important to long-term performance

Mitigation of strontium and ruthenium release in the CANDU primary heat transport system

Energy Technology Data Exchange (ETDEWEB)

McFarlane, J

1998-03-01

In certain severe accident scenarios, low-volatility fission products can appear to contribute significantly to dose, if treated with undue conservatism. Hence a survey was performed, to see if factors that may mitigate release of strontium and ruthenium could be incorporated into safety analyses, to cover parameters such as location in the fuel matrix under normal operating conditions, release from fuel, transport and deposition in the primary heat transport system and chemistry. In addition chemical equilibrium calculations were performed to investigate the volatility of strontium and ruthenium in the presence of uranium and important fission products. Strontium is very soluble in the U0{sub 2} fuel, up to 12 atom %, and hence release is improbable, particularly under oxidizing conditions until volatilization of the fuel matrix itself occurs. Ruthenium, however, can be released at low temperatures, but only under oxidizing conditions. These may occur during a fuel-handling accident or as a result of an end-fitting failure. Under these conditions, the primary heat transport system cannot be credited for retention. The volatile form of ruthenium, RuO{sub 4}(g), is thermally unstable above 381 K and decomposes to RuO{sub 2}(s) and O{sub 2}(g) upon contact with surfaces, a factor that is likely to minimize the release of ruthenium into the environment. (author)

Slow phasic changes in nucleus accumbens dopamine release during fixed ratio acquisition: a microdialysis study.

Science.gov (United States)

Segovia, K N; Correa, M; Salamone, J D

2011-11-24

Nucleus accumbens dopamine (DA) is a critical component of the brain circuitry regulating behavioral output during reinforcement-seeking behavior. Several studies have investigated the characteristics of accumbens DA release during the performance of well-learned operant behaviors, but relatively few have focused on the initial acquisition of particular instrumental behaviors or operant schedules. The present experiments focused on the initial acquisition of operant performance on a reinforcement schedule by studying the transition from a fixed ratio 1 (FR1) schedule to another operant schedule with a higher ratio requirement (i.e. fixed ratio 5 [FR5]). Microdialysis sessions were conducted in different groups of rats that were tested on either the FR1 schedule; the first, second, or third day of FR5 training; or after weeks of FR5 training. Consistent with previous studies, well-trained rats performing on the FR5 schedule after weeks of training showed significant increases in extracellular DA in both core and shell subregions of nucleus accumbens during the behavioral session. On the first day of FR5 training, there was a substantial increase in DA release in nucleus accumbens shell (i.e. approximately 300% of baseline). In contrast, accumbens core DA release was greatest on the second day of FR5 training. In parallel experiments, DA release in core and shell subregions did not significantly increase during free consumption of the same high carbohydrate food pellets that were used in the operant experiments, despite the very high levels of food intake in experienced rats. However, in rats exposed to the high-carbohydrate food for the first time, there was a tendency for extracellular DA to show a small increase. These results demonstrate that transient increases in accumbens DA release occur during the initial acquisition of ratio performance, and suggest that core and shell subregions show different temporal patterns during acquisition of instrumental behavior

Isotopic study of the comparative uptake and release of ions by deciduous and permanent dental enamel

International Nuclear Information System (INIS)

Tetteh, G.K.

1975-01-01

A comparative study of the uptake and release of calcium, orthophosphate, strontium and sodium from decidus and permanent dental enamel has been made using radioactive techniques. The rates of uptake and release of orthophosphate, strontium and sodium were observed to be greater in deciduous than in permanent enamel. However, for calcium, the rate of uptake was observed to be greater in the deciduous than in the permanent enamel but the rate of release was observed to be smaller in the deciduous enamel. These results in conjunction with the findings of Tetteh (1974) suggest that most of the calcification in the early stages of development of dental enamel is by a hetero-ionic exchange. (author) [fr

Isotopic study of the comparative uptake and release of ions by deciduous and permanent dental enamel

Energy Technology Data Exchange (ETDEWEB)

Tetteh, G K [Department of Physics, University of Ghana,Legon

1975-04-01

A comparative study of the uptake and release of calcium, orthophosphate, strontium and sodium from decidus and permanent dental enamel has been made using radioactive techniques. The rates of uptake and release of orthophosphate, strontium and sodium were observed to be greater in deciduous than in permanent enamel. However, for calcium, the rate of uptake was observed to be greater in the deciduous than in the permanent enamel but the rate of release was observed to be smaller in the deciduous enamel. These results in conjunction with the findings of Tetteh (1974) suggest that most of the calcification in the early stages of development of dental enamel is by a hetero-ionic exchange.

Hydrogen Gas Retention and Release from WTP Vessels: Summary of Preliminary Studies

Energy Technology Data Exchange (ETDEWEB)

Gauglitz, Phillip A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bontha, Jagannadha R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Daniel, Richard C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mahoney, Lenna A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rassat, Scot D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wells, Beric E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Bao, Jie [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Boeringa, Gregory K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buchmiller, William C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Burns, Carolyn A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chun, Jaehun [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Karri, Naveen K. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Li, Huidong [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tran, Diana N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-07-01

The Hanford Waste Treatment and Immobilization Plant (WTP) is currently being designed and constructed to pretreat and vitrify a large portion of the waste in the 177 underground waste storage tanks at the Hanford Site. A number of technical issues related to the design of the pretreatment facility (PTF) of the WTP have been identified. These issues must be resolved prior to the U.S. Department of Energy (DOE) Office of River Protection (ORP) reaching a decision to proceed with engineering, procurement, and construction activities for the PTF. One of the issues is Technical Issue T1 - Hydrogen Gas Release from Vessels (hereafter referred to as T1). The focus of T1 is identifying controls for hydrogen release and completing any testing required to close the technical issue. In advance of selecting specific controls for hydrogen gas safety, a number of preliminary technical studies were initiated to support anticipated future testing and to improve the understanding of hydrogen gas generation, retention, and release within PTF vessels. These activities supported the development of a plan defining an overall strategy and approach for addressing T1 and achieving technical endpoints identified for T1. Preliminary studies also supported the development of a test plan for conducting testing and analysis to support closing T1. Both of these plans were developed in advance of selecting specific controls, and in the course of working on T1 it was decided that the testing and analysis identified in the test plan were not immediately needed. However, planning activities and preliminary studies led to significant technical progress in a number of areas. This report summarizes the progress to date from the preliminary technical studies. The technical results in this report should not be used for WTP design or safety and hazards analyses and technical results are marked with the following statement: “Preliminary Technical Results for Planning – Not to be used for WTP Design

Assessment of Ions released from Three Types of Orthodontic Brackets immersed in Different Mouthwashes: An in vitro Study.

Science.gov (United States)

Nahidh, Mohammed; Garma, Noor Mh; Jasim, Esraa S

2018-01-01

Herbs are used widely in medicine. The purpose of the present study was to assess the ion release from gold-plated orthodontic bracket compared with other stainless steel brackets, and based on the findings of the study, the orthodontists can choose the most biocompatible brackets and mouthwashes useful in the clinical practice. A total of 150 orthodontic brackets from Orthotechnology™ Company, USA (50 stainless steel one-piece brackets, 50 stainless steel two-piece brackets, and 50 gold brackets) were immersed in four mouthwashes in addition to distilled water. Ten of each type of brackets in every media were immersed under 37°C for 45 days. Ions released in these mouthwashes were measured, and comparisons among different bracket types and among various mouthwashes were done by one-way analysis of variance (ANOVA) and then with Games-Howell tests. Increased amounts of ions released in herbal mouth-washes were recorded in gold and two-piece brackets in comparison with one-piece stainless steel brackets. Herbal mouthwashes must be used with caution as they showed an increased amount of ions released in comparison with chlorhexidine. One-piece stainless steel bracket system is the most compatible bracket type, as they released the least amount of ions. One-piece stainless steel brackets are better than two-piece brackets in terms of ions released.

Particle Release Experiment (PRex) Final Report

Energy Technology Data Exchange (ETDEWEB)

Keillor, Martin E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Arrigo, Leah M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Detwiler, Rebecca S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kernan, Warnick J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kirkham, Randy R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); MacDougall, Matthew R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chipman, Veraun D. [National Security Technologies, LLC. (NSTec), Mercury, NV (United States); Milbrath, Brian D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rishel, Jeremy P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Seifert, Allen [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Seifert, Carolyn E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Smart, John E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Emer, Dudley [National Security Technologies, LLC. (NSTec), Mercury, NV (United States)

2014-09-30

An experiment to release radioactive particles representative of small-scale venting from an underground nuclear test was conducted to gather data in support of treaty verification and monitoring activities. For this experiment, a CO₂-driven “air cannon” was used to release La-140 at ambient temperatures. Lanthanum-140 was chosen to represent the fission fragments because of its short half-life and prominent gamma-ray emissions; the choice was also influenced by the successful production and use of La-140 with low levels of radioactive contaminants in a Defence Research and Development Canada Field Trial. The source was created through activation of high-purity natural lanthanum oxide at the reactor of Washington State University, Pullman, Washington. Multiple varieties of witness plates and air samplers were laid in an irregular grid covering the area over which the plume was modeled to deposit. Aerial survey, a NaI(Tl) mobile spectrometer, and handheld and backpack instruments ranging from polyvinyl toluene to high-purity germanium were used to survey the plume. Additionally, three varieties of soil sampling were investigated. The relative sensitivity and utility of sampling and survey methods are discussed in the context of On-Site Inspection. The measurements and samples show a high degree of correlation and form a valuable set of test data.

Accidental releases of radionuclides: a preliminary study of the consequences of land contamination

International Nuclear Information System (INIS)

Simmonds, J.R.; Haywood, S.M.; Linsley, G.S.

1982-10-01

The long term consequences of land contamination from accidental releases of activity from thermal reactors are examined. The radiological consequences are assessed using an analysis of the exposure of individuals and the population to ground deposits of the radionuclides released. The contribution of the different nuclides in the release by their various exposure routes to the irradiation of man are calculated as a function of time after release and the most radiologically important are identified. A preliminary assessment is made of off-site economic and social consequences of accidental releases by estimating the areas of land which would be affected by the introduction of countermeasures to control individual radiation exposure due to external irradiation from ground deposits (relocation of populations), and the intake of radionuclides contained in locally produced foodstuffs (restrictions on food production). The areas where administrative controls would be necessary decline in size with time after the release; estimates are made of this time-dependent behaviour using dynamic environmental transfer models. Finally, the collective doses saved by the introduction of countermeasures are estimated using population and agricultural distribution data for a rural location in the United Kingdom. (author)

Contribution to the study of the fission-gas release in metallic nuclear fuels

International Nuclear Information System (INIS)

Kryger, B.

1969-10-01

In order to study the effect of an external pressure on the limitation of swelling due to fission-gas precipitation, some irradiations have been carried out at burn-ups of about 35.000 MWd/ton, and at average sample temperatures of 575 Celsius degrees, of non-alloyed uranium and uranium 8 per cent molybdenum gained in a thick stainless steel can. A cylindrical central hole allows a fuel swelling from 20 to 33 per cent according to the experiment. After irradiation, the uranium samples showed two types of can rupture: one is due to the fuel swelling, and the other, to the pressure of the fission gases, released through a network of microcracks. The cans of the uranium-molybdenum samples are all undamaged and it is shown that the gas release occurs by interconnection of the bubbles for swelling values higher than those obtained in the case of uranium. For each type of fuel, a swelling-fission gas release relationship is established. The results suggest that good performances with a metallic fuel intended for use in fast reactor conditions can be obtained. (author) [fr

Investigation of delayed fission gas release

International Nuclear Information System (INIS)

Cayet, Nicolas

1996-05-01

The study of the fission gas release process in the high burnup rig IFA-562 has revealed a particular fuel behaviour: a delay in the fission gas release process. It appeared that an important release of gas was measured by the pressure transducers once the power had decreased, whereas, during steady-state operation, the pressure did not increase very much. After examinations, the gap size has been concluded to be the main parameter involving this delay. However the burnup could have been a potential factor, its role is mainly to close the gap by swelling. The observations of low burnup rods have shown the same delayed fission gas release, the gap being small by design and closed essentially by thermal expansion. The study of the kinetics has demonstrated the time-independency of the phenomenon. Thus the proposed mechanism driving this delayed fission gas release would involve three consecutives stages. During steady-state, the gas is released into the interlinkage network of grain boundary bubbles and cracks. Due to the closed gap, the gas is trapped in some void volumes, unable to escape the pellet. During power reduction, the gap and some old/new cracks open, immediately providing a path for the gas to the pressure transducers and explaining this delay in the fission gas release. (author)

Electro-thermometric study on the healing of free gingival grafts covered by two different dressings.

Science.gov (United States)

Jańczuk, Z; Banach, J; Pastusiak, J; Syryńska, M; Zakrzewski, J

1990-01-01

The aim of the study was to evaluate the healing of the gingival grafts covered with Solcoseryl dental adhesive paste (Solco Basel AG) in comparison with the grafts covered with Peripac. By means of thermistor thermometer coupled with a chart recorder, three series of temperature as time recordings of grafted tissues after normalized cooling were performed--before grafting, 2 and 12 weeks after grafting. On the basis of temperature recovery curves obtained, the blood supply coefficients were computed. It was revealed that in the Solcoseryl group there was an improvement in blood supply in 75% of the cases--2 weeks, and 66%--12 weeks after grafting. In the other group, the same reaction was observed only in 50% and 30% of the cases respectively.

MANAGEMENT EFFECTS ON GROUND COVER CLUMPINESS: SCALING FROM FIELD TO SENTINEL-2 COVER ESTIMATES

Directory of Open Access Journals (Sweden)

P. Scarth

2017-11-01

Full Text Available Significant progress has been made in the development of cover data and derived products based on remotely sensed fractional cover information and field data across Australia, and these cover data sets are now used for quantifying and monitoring grazing land condition. The availability of a dense time-series of nearly 30 years of cover data to describe the spatial and temporal patterns in landscape changes over time can help with monitoring the effectiveness of grazing land management practice change. With the advent of higher spatial resolution data, such as that provided by the Copernicus Sentinel 2 series of satellites, we can look beyond reporting purely on cover amount and more closely at the operational monitoring and reporting on spatial arrangement of cover and its links with land condition. We collected high spatial resolution cover transects at 20 cm intervals over the Wambiana grazing trials in the Burdekin catchment in Queensland, Australia. Spatial variance analysis was used to determine the cover autocorrelation at various support intervals. Coincident Sentinel-2 imagery was collected and processed over all the sites providing imagery to link with the field data. We show that the spatial arrangement and temporal dynamics of cover are important indicators of grazing land condition for both productivity and water quality outcomes. The metrics and products derived from this research will assist land managers to prioritize investment and practice change strategies for long term sustainability and improved water quality, particularly in the Great Barrier Reef catchments.

Replacing fallow by cover crops: economic sustainability

Science.gov (United States)

Gabriel, José Luis; Garrido, Alberto; Quemada, Miguel

2013-04-01

Replacing fallow by cover crops in intensive fertilized systems has been demonstrated as an efficient tool for reducing nitrate leaching. However, despite the evident environmental services provided and the range of agronomic benefits documented in the literature, farmers' adoption of this new technology is still limited because they are either unwilling or unable, although adoption reluctance is frequently rooted in low economic profitability, low water se efficiency or poor knowledge. Economic analyses permit a comparison between the profit that farmers obtain from agricultural products and the cost of adopting specific agricultural techniques. The goal of this study was to evaluate the economic impact of replacing the usual winter fallow with cover crops (barley (Hordeum vulgare L., cv. Vanessa), vetch (Vicia villosa L., cv. Vereda) and rapeseed (Brassica napus L., cv. Licapo)) in irrigated maize systems and variable Mediterranean weather conditions using stochastic Monte-Carlo simulations of key farms' financial performance indicators. The three scenarios studied for each cover crop were: i) just leaving the cover crop residue in the ground, ii) leaving the cover crop residue but reduce following maize fertilization according to the N available from the previous cover crop and iii) selling the cover crop residue for animal feeding. All the scenarios were compared with respect to a typical maize-fallow rotation. With observed data from six different years and in various field trials, looking for different weather conditions, probability distribution functions of maize yield, cover crop biomass production and N fertilizer saving was fitted. Based in statistical sources maize grain price, different forage prices and the cost of fertilizer were fitted to probability distribution functions too. As result, introducing a cover crop involved extra costs with respect to fallow as the initial investment, because new seed, herbicide or extra field operations. Additional

Arsenic release from arsenopyrite weathering: Insights from sequential extraction and microscopic studies

Energy Technology Data Exchange (ETDEWEB)

Basu, Ankan [Marshall Miller and Associates, Bluefield VA (United States); Department of Geosciences, Virginia Tech, 4044 Derring Hall, Blacksburg VA 24061 (United States); Schreiber, Madeline E., E-mail: mschreib@vt.edu [Department of Geosciences, Virginia Tech, 4044 Derring Hall, Blacksburg VA 24061 (United States)

2013-11-15

Highlights: ► We studied arsenopyrite weathering reactions in rocks and sediments at mine site. ► Arsenopyrite oxidizes to scorodite, which dissolves incongruently to Fe hydroxide. ► Weathering of arsenopyrite to Fe hydroxide releases As to water. ► Dominant As reservoir in sediment is Fe hydroxide. -- Abstract: At a former As mine site, arsenopyrite oxidation has resulted in formation of scorodite and As-bearing iron hydroxide, both in host rock and mine tailings. Electron microprobe analysis documents that arsenopyrite weathers along two pathways: one that involves formation of sulfur, and one that does not. In both pathways, arsenopyrite oxidizes to form scorodite, which dissolves incongruently to form As-bearing iron hydroxides. From a mass balance perspective, arsenopyrite oxidation to scorodite conserves As, but as scorodite dissolves incongruently to iron hydroxides, As is released to solution, resulting in elevated As concentrations in the headwater stream adjacent to the site. The As-bearing iron hydroxide is the dominant solid phase reservoir of As in mine tailings and stream sediment, as suggested by sequential extraction. This As-bearing iron hydroxide is stable under the aerobic and pH 4–6 conditions at the site; however, changes in biogeochemical conditions resulting from sediment burial or future remedial efforts, which could promote As release from this reservoir due to reductive dissolution, should be avoided.

Arsenic release from arsenopyrite weathering: Insights from sequential extraction and microscopic studies

International Nuclear Information System (INIS)

Basu, Ankan; Schreiber, Madeline E.

2013-01-01

Highlights: ► We studied arsenopyrite weathering reactions in rocks and sediments at mine site. ► Arsenopyrite oxidizes to scorodite, which dissolves incongruently to Fe hydroxide. ► Weathering of arsenopyrite to Fe hydroxide releases As to water. ► Dominant As reservoir in sediment is Fe hydroxide. -- Abstract: At a former As mine site, arsenopyrite oxidation has resulted in formation of scorodite and As-bearing iron hydroxide, both in host rock and mine tailings. Electron microprobe analysis documents that arsenopyrite weathers along two pathways: one that involves formation of sulfur, and one that does not. In both pathways, arsenopyrite oxidizes to form scorodite, which dissolves incongruently to form As-bearing iron hydroxides. From a mass balance perspective, arsenopyrite oxidation to scorodite conserves As, but as scorodite dissolves incongruently to iron hydroxides, As is released to solution, resulting in elevated As concentrations in the headwater stream adjacent to the site. The As-bearing iron hydroxide is the dominant solid phase reservoir of As in mine tailings and stream sediment, as suggested by sequential extraction. This As-bearing iron hydroxide is stable under the aerobic and pH 4–6 conditions at the site; however, changes in biogeochemical conditions resulting from sediment burial or future remedial efforts, which could promote As release from this reservoir due to reductive dissolution, should be avoided

Formulation, release characteristics, and bioavailability study of gastroretentive floating matrix tablet and floating raft system of Mebeverine HCl.

Science.gov (United States)

El Nabarawi, Mohamed A; Teaima, Mahmoud H; Abd El-Monem, Rehab A; El Nabarawy, Nagla A; Gaber, Dalia A

2017-01-01

To prolong the residence time of dosage forms within the gastrointestinal tract until all drug is released at the desired rate is one of the real challenges for oral controlled-release drug delivery systems. This study was designed to develop a controlled-release floating matrix tablet and floating raft system of Mebeverine HCl (MbH) and evaluate different excipients for their floating behavior and in vitro controlled-release profiles. Oral pharmacokinetics of the optimum matrix tablet, raft system formula, and marketed Duspatalin ® 200 mg retard as reference were studied in beagle dogs. The optimized tablet formula (FT-10) and raft system formula (FRS-11) were found to float within 34±5 sec and 15±7 sec, respectively, and both remain buoyant over a period of 12 h in simulated gastric fluid. FT-10 (Compritol/HPMC K100M 1:1) showed the slowest drug release among all prepared tablet formulations, releasing about 80.2% of MbH over 8 h. In contrast, FRS-11 (Sodium alginate 3%/HPMC K100M 1%/Precirol 2%) had the greatest retardation, providing sustained release of 82.1% within 8 h. Compared with the marketed MbH product, the C max of FT-10 was almost the same, while FRS-11 maximum concentration was higher. The t max was 3.33, 2.167, and 3.0 h for marketed MbH product, FT-10, and FRS-11, respectively. In addition, the oral bioavailability experiment showed that the relative bioavailability of the MbH was 104.76 and 116.01% after oral administration of FT-10 and FRS-11, respectively, compared to marketed product. These results demonstrated that both controlled-released floating matrix tablet and raft system would be promising gastroretentive delivery systems for prolonging drug action.

WE-AB-BRA-03: Non-Invasive Controlled Release from Implantable Hydrogel Scaffolds Using Ultrasound

Energy Technology Data Exchange (ETDEWEB)

Moncion, A; Kripfgans, O.D; Putnam, A.J; Frances chi, R.T; Fabiilli, M.L [University of Michigan, Ann Arbor, MI (United States)

2016-06-15

Purpose: To control release of a model payload in acoustically responsive scaffolds (ARSs) using focused ultrasound (FUS). Methods: Fluorescently-labeled dextran (10 kDa) was encapsulated in sonosensitive perfluorocarbon (C{sub 6}F{sub 14} or C{sub 5}F{sub 12}) double emulsions (mean diameter: 2.9±0.1 µm). For in vitro release studies, 0.5 mL ARSs (10 mg/mL fibrin, 1% (v/v) emulsion) were polymerized in 24 well plates and covered with 0.5 mL medium. Starting one day after polymerization, ARSs were exposed to FUS (2.5 MHz, Pr = 8 MPa, 13 cycles, 100 Hz PRF) for 2 min daily. The amount of dextran released into the media was quantified. For in vivo studies, 0.25 mL ARSs were prepared as described previously and injected subcutaneously in the lower back of BALB/c mice. After polymerization, a subset of the implanted ARSs were exposed to FUS (as previously described). Animals were imaged longitudinally using a fluorescence imaging system to quantify the amount of dextran released from the ARSs. Results: In vitro: Over 6 days, +FUS displayed an 8.2-fold increase in dextran release compared to −FUS (−FUS: 2.7±0.6%; +FUS: 22.2±3.0%) for C{sub 6}F{sub 14} ARSs, and a 6.7-fold increase (−FUS: 5.0±0.8%; +FUS: 38.5±1.6%) for C{sub 5}F{sub 12}:C{sub 6}F{sub 14} ARSs. In vivo: +FUS displayed statistically greater dextran release compared to −FUS one day after implantation for C{sub 5}F{sub 12}:C{sub 6}F{sub 14} ARSs (−FUS: 55.1±1.5%; +FUS: 74.1±2.2%) and three days after implantation for C{sub 6}F{sub 14} ARSs (−FUS: 1.4±6.5%; +FUS: 30.4±5.4%). Conclusion: FUS enables non-invasive control of payload release from an ARS, which could benefit growth factor delivery for tissue regeneration. ARS are versatile due to their tunability (i.e. stiffness, emulsion composition, FUS pressure, FUS frequency, etc.) and can be modified to for optimal payload release. Future work will optimize ARS formulations for in vivo use to minimize payload release in the absence of

Simulation Studies of Diffusion-Release and Effusive-Flow of Short-Lived Radioactive Isotopes

CERN Document Server

Zhang, Yan; Kawai, Yoko

2005-01-01

Delay times associated with diffusion release from targets and effusive-flow transport of radioactive isotopes to ion sources are principal intensity limiters at ISOL-based radioactive ion beam facilities, and simulation studies with computer models are cost effective methods for designing targets and vapor transport systems with minimum delay times to avoid excessive decay losses of short lived ion species. A finite difference code, Diffuse II, was recently developed at the Oak Ridge National Laboratory to study diffusion-release of short-lived species from three principal target geometries. Simulation results are in close agreement with analytical solutions to Fick’s second equation. Complementary to the development of Diffuse II, the Monte-Carlo code, Effusion, was developed to address issues related to the design of fast vapor transport systems. Results, derived by using Effusion, are also found to closely agree with experimental measurements. In this presentation, the codes will be used in conc...

FFTF sodium and cover gas characterization and purification

International Nuclear Information System (INIS)

McCown, J.J.; Bloom, G.R.; Meadows, G.E.; Mettler, G.W.

1980-02-01

The FFTF Primary and Secondary Heat Transport System (HTS) sodium is purified with cold traps which have packed crystallizers and external economizers. The Primary HTS cold trap is NaK cooled and the Secondary HTS cold traps are air cooled. The FFTF cold traps have maintained high purity in the sodium since sodium fill. Plant operational procedures during fill and initial sodium heatup to 800 0 F were controlled to assure low release rates of impurities to the sodium. The FFTF sodium systems are monitored by plugging temperature indicators and by several sampling methods. During reactor fill and non-fueled operations at 400 to 800 0 F, impurity changes in the sodium were followed by continuous plugging indicator coverage, by exposing wires and foils to measure carbon, hydrogen and oxygen, and by bulk sample analysis of all other trace constituents. The sampling and analysis methods and data are presented, impurity excursions in the cover gas and sodium are described, and impurity trends are discussed

Review on fluoride-releasing restorative materials--fluoride release and uptake characteristics, antibacterial activity and influence on caries formation.

Science.gov (United States)

Wiegand, Annette; Buchalla, Wolfgang; Attin, Thomas

2007-03-01

The purpose of this article was to review the fluoride release and recharge capabilities, and antibacterial properties, of fluoride-releasing dental restoratives, and discuss the current status concerning the prevention or inhibition of caries development and progression. Information from original scientific full papers or reviews listed in PubMed (search term: fluoride release AND (restorative OR glass-ionomer OR compomer OR polyacid-modified composite resin OR composite OR amalgam)), published from 1980 to 2004, was included in the review. Papers dealing with endodontic or orthodontic topics were not taken into consideration. Clinical studies concerning secondary caries development were only included when performed in split-mouth design with an observation period of at least three years. Fluoride-containing dental materials show clear differences in the fluoride release and uptake characteristics. Short- and long-term fluoride releases from restoratives are related to their matrices, setting mechanisms and fluoride content and depend on several environmental conditions. Fluoride-releasing materials may act as a fluoride reservoir and may increase the fluoride level in saliva, plaque and dental hard tissues. However, clinical studies exhibited conflicting data as to whether or not these materials significantly prevent or inhibit secondary caries and affect the growth of caries-associated bacteria compared to non-fluoridated restoratives. Fluoride release and uptake characteristics depend on the matrices, fillers and fluoride content as well as on the setting mechanisms and environmental conditions of the restoratives. Fluoride-releasing materials, predominantly glass-ionomers and compomers, did show cariostatic properties and may affect bacterial metabolism under simulated cariogenic conditions in vitro. However, it is not proven by prospective clinical studies whether the incidence of secondary caries can be significantly reduced by the fluoride release of

Landfill covers for dry environments

International Nuclear Information System (INIS)

Dwyer, S.F.

1996-01-01

A large-scale landfill cover field test is currently underway at Sandia National Laboratories in Albuquerque, New Mexico. It is intended to compare and document the performance of alternative landfill cover technologies of various costs and complexities for interim stabilization and/or final closure of landfills in arid and semi-arid environments. Test plots of traditional designs recommended by the US Environmental Protection Agency for both RCRA Subtitle open-quote C close-quote and open-quote D close-quote regulated facilities have been constructed side-by-side with the alternative covers and will serve as baselines for comparison to these alternative covers. The alternative covers were designed specifically for dry environments. The covers will be tested under both ambient and stressed conditions. All covers have been instrumented to measure water balance variables and soil temperature. An on-site weather station records all pertinent climatological data. A key to acceptance of an alternative environmental technology is seeking regulatory acceptance and eventual permitting. The lack of acceptance by regulatory agencies is a significant barrier to development and implementation of innovative cover technologies. Much of the effort on this demonstration has been toward gaining regulatory and public acceptance

Accelerated in-vitro release testing methods for extended-release parenteral dosage forms.

Science.gov (United States)

Shen, Jie; Burgess, Diane J

2012-07-01

This review highlights current methods and strategies for accelerated in-vitro drug release testing of extended-release parenteral dosage forms such as polymeric microparticulate systems, lipid microparticulate systems, in-situ depot-forming systems and implants. Extended-release parenteral dosage forms are typically designed to maintain the effective drug concentration over periods of weeks, months or even years. Consequently, 'real-time' in-vitro release tests for these dosage forms are often run over a long time period. Accelerated in-vitro release methods can provide rapid evaluation and therefore are desirable for quality control purposes. To this end, different accelerated in-vitro release methods using United States Pharmacopeia (USP) apparatus have been developed. Different mechanisms of accelerating drug release from extended-release parenteral dosage forms, along with the accelerated in-vitro release testing methods currently employed are discussed. Accelerated in-vitro release testing methods with good discriminatory ability are critical for quality control of extended-release parenteral products. Methods that can be used in the development of in-vitro-in-vivo correlation (IVIVC) are desirable; however, for complex parenteral products this may not always be achievable. © 2012 The Authors. JPP © 2012 Royal Pharmaceutical Society.

Accelerated in vitro release testing methods for extended release parenteral dosage forms

Science.gov (United States)

Shen, Jie; Burgess, Diane J.

2012-01-01

Objectives This review highlights current methods and strategies for accelerated in vitro drug release testing of extended release parenteral dosage forms such as polymeric microparticulate systems, lipid microparticulate systems, in situ depot-forming systems, and implants. Key findings Extended release parenteral dosage forms are typically designed to maintain the effective drug concentration over periods of weeks, months or even years. Consequently, “real-time” in vitro release tests for these dosage forms are often run over a long time period. Accelerated in vitro release methods can provide rapid evaluation and therefore are desirable for quality control purposes. To this end, different accelerated in vitro release methods using United States Pharmacopoeia (USP) apparatus have been developed. Different mechanisms of accelerating drug release from extended release parenteral dosage forms, along with the accelerated in vitro release testing methods currently employed are discussed. Conclusions Accelerated in vitro release testing methods with good discriminatory ability are critical for quality control of extended release parenteral products. Methods that can be used in the development of in vitro-in vivo correlation (IVIVC) are desirable, however for complex parenteral products this may not always be achievable. PMID:22686344

Analysis of drug effects on neurotransmitter release

International Nuclear Information System (INIS)

Rowell, P.; Garner, A.

1986-01-01

The release of neurotransmitter is routinely studied in a superfusion system in which serial samples are collected and the effects of drugs or other treatments on the amount of material in the superfusate is determined. With frequent sampling interval, this procedure provides a mechanism for dynamically characterizing the release process itself. Using automated data collection in conjunction with polyexponential computer analysis, the equation which describes the release process in each experiment is determined. Analysis of the data during the nontreated phase of the experiment allows an internal control to be used for accurately assessing any changes in neurotransmitter release which may occur during a subsequent treatment phase. The use of internal controls greatly improves the signal to noise ratio and allows determinations of very low concentrations of drugs on small amounts of tissue to be made. In this presentation, the effects of 10 μM nicotine on 3 H-dopamine release in rat nucleus accumbens is described. The time course, potency and efficacy of the drug treatment is characterized using this system. Determinations of the exponential order of the release as well as the rate constants allow one to study the mechanism of the release process. A description of 3 H-dopamine release in normal as well as Ca ++ -free medium is presented