End-to-End Joint Antenna Selection Strategy and Distributed Compress and Forward Strategy for Relay Channels

Directory of Open Access Journals (Sweden)

Rahul Vaze

2009-01-01

Full Text Available Multihop relay channels use multiple relay stages, each with multiple relay nodes, to facilitate communication between a source and destination. Previously, distributed space-time codes were proposed to maximize the achievable diversity-multiplexing tradeoff; however, they fail to achieve all the points of the optimal diversity-multiplexing tradeoff. In the presence of a low-rate feedback link from the destination to each relay stage and the source, this paper proposes an end-to-end antenna selection (EEAS strategy as an alternative to distributed space-time codes. The EEAS strategy uses a subset of antennas of each relay stage for transmission of the source signal to the destination with amplifying and forwarding at each relay stage. The subsets are chosen such that they maximize the end-to-end mutual information at the destination. The EEAS strategy achieves the corner points of the optimal diversity-multiplexing tradeoff (corresponding to maximum diversity gain and maximum multiplexing gain and achieves better diversity gain at intermediate values of multiplexing gain, versus the best-known distributed space-time coding strategies. A distributed compress and forward (CF strategy is also proposed to achieve all points of the optimal diversity-multiplexing tradeoff for a two-hop relay channel with multiple relay nodes.

Outage probability of distributed beamforming with co-channel interference

KAUST Repository

Yang, Liang

2012-03-01

In this letter, we consider a distributed beamforming scheme (DBF) in the presence of equal-power co-channel interferers for both amplify-and-forward and decode-and-forward relaying protocols over Rayleigh fading channels. We first derive outage probability expressions for the DBF systems. We then present a performance analysis for a scheme relying on source selection. Numerical results are finally presented to verify our analysis. © 2011 IEEE.

Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks.

Science.gov (United States)

Lee, Jong-Ho; Sohn, Illsoo; Kim, Yong-Hwa

2017-05-16

In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF) relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks.

Switched diversity strategies for dual-hop relaying systems

KAUST Repository

Gaaloul, Fakhreddine

2011-04-29

This paper investigates the effect of different switched diversity configurations on the implementation complexity and achieved performance of dual-hop amplify-and-forward (AF) relaying networks. A low-complexity model of the relay station is adopted, wherein single-input single-output antenna configuration is employed. Each of the transmitter and the receiver however employs multiple antennas to improve the overall link performance. Single-phase and two-phase based receive switching strategies are investigated assuming optimum first hop signal-to-noise ratio (SNR). Moreover, the simple scheme in which the switched diversity is applied independently over the two hops is studied using tight upper bounds. Thorough performance comparisons and switching thresholds optimization for the aforementioned strategies are presented. Simulation results are also provided to validate the mathematical development and to verify the numerical computations.

The sequence relay selection strategy based on stochastic dynamic programming

Science.gov (United States)

Zhu, Rui; Chen, Xihao; Huang, Yangchao

2017-07-01

Relay-assisted (RA) network with relay node selection is a kind of effective method to improve the channel capacity and convergence performance. However, most of the existing researches about the relay selection did not consider the statically channel state information and the selection cost. This shortage limited the performance and application of RA network in practical scenarios. In order to overcome this drawback, a sequence relay selection strategy (SRSS) was proposed. And the performance upper bound of SRSS was also analyzed in this paper. Furthermore, in order to make SRSS more practical, a novel threshold determination algorithm based on the stochastic dynamic program (SDP) was given to work with SRSS. Numerical results are also presented to exhibit the performance of SRSS with SDP.

Numerical analysis of biosonar beamforming mechanisms and strategies in bats.

Science.gov (United States)

Müller, Rolf

2010-09-01

Beamforming is critical to the function of most sonar systems. The conspicuous noseleaf and pinna shapes in bats suggest that beamforming mechanisms based on diffraction of the outgoing and incoming ultrasonic waves play a major role in bat biosonar. Numerical methods can be used to investigate the relationships between baffle geometry, acoustic mechanisms, and resulting beampatterns. Key advantages of numerical approaches are: efficient, high-resolution estimation of beampatterns, spatially dense predictions of near-field amplitudes, and the malleability of the underlying shape representations. A numerical approach that combines near-field predictions based on a finite-element formulation for harmonic solutions to the Helmholtz equation with a free-field projection based on the Kirchhoff integral to obtain estimates of the far-field beampattern is reviewed. This method has been used to predict physical beamforming mechanisms such as frequency-dependent beamforming with half-open resonance cavities in the noseleaf of horseshoe bats and beam narrowing through extension of the pinna aperture with skin folds in false vampire bats. The fine structure of biosonar beampatterns is discussed for the case of the Chinese noctule and methods for assessing the spatial information conveyed by beampatterns are demonstrated for the brown long-eared bat.

Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks

Science.gov (United States)

Lee, Jong-Ho; Sohn, Illsoo; Kim, Yong-Hwa

2017-01-01

In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF) relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks. PMID:28509841

Simultaneous Wireless Power Transfer and Secure Multicasting in Cooperative Decode-and-Forward Relay Networks

Directory of Open Access Journals (Sweden)

Jong-Ho Lee

2017-05-01

Full Text Available In this paper, we investigate simultaneous wireless power transfer and secure multicasting via cooperative decode-and-forward (DF relays in the presence of multiple energy receivers and eavesdroppers. Two scenarios are considered under a total power budget: maximizing the minimum harvested energy among the energy receivers under a multicast secrecy rate constraint; and maximizing the multicast secrecy rate under a minimum harvested energy constraint. For both scenarios, we solve the transmit power allocation and relay beamformer design problems by using semidefinite relaxation and bisection technique. We present numerical results to analyze the energy harvesting and secure multicasting performances in cooperative DF relay networks.

Emergency Load Shedding Strategy Based on Sensitivity Analysis of Relay Operation Margin against Cascading Events

DEFF Research Database (Denmark)

Liu, Zhou; Chen, Zhe; Sun, Haishun Sun

2012-01-01

the runtime emergent states of related system component. Based on sensitivity analysis between the relay operation margin and power system state variables, an optimal load shedding strategy is applied to adjust the emergent states timely before the unwanted relay operation. Load dynamics is also taken...... into account to compensate load shedding amount calculation. And the multi-agent technology is applied for the whole strategy implementation. A test system is built in real time digital simulator (RTDS) and has demonstrated the effectiveness of the proposed strategy.......In order to prevent long term voltage instability and induced cascading events, a load shedding strategy based on the sensitivity of relay operation margin to load powers is discussed and proposed in this paper. The operation margin of critical impedance backup relay is defined to identify...

Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

KAUST Repository

Sungjoon Park,

2011-11-01

In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula for opportunistic relaying in the channel, and validate the results by comparing it with the exact outage probability. Also, we suggest a new relay selection algorithm that incorporates shadowing. We consider a protocol of broadcasting the channel gain of the previously selected relay. This saves resources in slow fading channel by reducing collisions in relay selection. We further investigate the optimal relay selection period to maximize the throughput while avoiding selection overhead. © 2011 IEEE.

Secure Communication for Two-Way Relay Networks with Imperfect CSI

Directory of Open Access Journals (Sweden)

Cong Sun

2017-09-01

Full Text Available This paper considers a two-way relay network, where two legitimate users exchange messages through several cooperative relays in the presence of an eavesdropper, and the Channel State Information (CSI of the eavesdropper is imperfectly known. The Amplify-and-Forward (AF relay protocol is used. We design the relay beamforming weights to minimize the total relay transmit power, while requiring the Signal-to-Noise-Ratio (SNRs of the legitimate users to be higher than the given thresholds and the achievable rate of the eavesdropper to be upper-bounded. Due to the imperfect CSI, a robust optimization problem is summarized. A novel iterative algorithm is proposed, where the line search technique is applied, and the feasibility is preserved during iterations. In each iteration, two Quadratically-Constrained Quadratic Programming (QCQP subproblems and a one-dimensional subproblem are optimally solved. The optimality property of the robust optimization problem is analyzed. Simulation results show that the proposed algorithm performs very close to the non-robust model with perfect CSI, in terms of the obtained relay transmit power; it~achieves higher secrecy rate compared to the existing work. Numerically, the proposed algorithm converges very quickly, and more than 85% of the problems are solved optimally.

Opportunistic relaying in multipath and slow fading channel: Relay selection and optimal relay selection period

KAUST Repository

Sungjoon Park,; Stark, Wayne E.

2011-01-01

In this paper we present opportunistic relay communication strategies of decode and forward relaying. The channel that we are considering includes pathloss, shadowing, and fast fading effects. We find a simple outage probability formula

Relaying Strategies and Protocols for Efficient Wireless Networks

KAUST Repository

Zafar, Ammar

2014-10-01

Next generation wireless networks are expected to provide high data rate and satisfy the Quality-of-Service (QoS) constraints of the users. A significant component of achieving these goals is to increase the effi ciency of wireless networks by either optimizing current architectures or exploring new technologies which achieve that. The latter includes revisiting technologies which were previously proposed, but due to a multitude of reasons were ignored at that time. One such technology is relaying which was initially proposed in the latter half of the 1960s and then was revived in the early 2000s. In this dissertation, we study relaying in conjunction with resource allocation to increase the effi ciency of wireless networks. In this regard, we differentiate between conventional relaying and relaying with buffers. Conventional relaying is traditional relaying where the relay forwards the signal it received immediately. On the other hand, in relaying with buffers or buffer-aided relaying as it is called, the relay can store received data in its buffer and forward it later on. This gives the benefit of taking advantage of good channel conditions as the relay can only transmit when the channel conditions are good. The dissertation starts with conventional relaying and considers the problem of minimizing the total consumed power while maintaining system QoS. After upper bounding the system performance, more practical algorithms which require reduced feedback overhead are explored. Buffer-aided relaying is then considered and the joint user-and-hop scheduler is introduced which exploits multi-user diversity (MUD) and 5 multi-hop diversity (MHD) gains together in dual-hop broadcast channels. Next joint user-and-hop scheduling is extended to the shared relay channel where two source-destination pairs share a single relay. The benefits of buffer-aided relaying in the bidirectional relay channel utilizing network coding are then explored. Finally, a new transmission protocol

Optimized Power Allocation and Relay Location Selection in Cooperative Relay Networks

Directory of Open Access Journals (Sweden)

Jianrong Bao

2017-01-01

Full Text Available An incremental selection hybrid decode-amplify forward (ISHDAF scheme for the two-hop single relay systems and a relay selection strategy based on the hybrid decode-amplify-and-forward (HDAF scheme for the multirelay systems are proposed along with an optimized power allocation for the Internet of Thing (IoT. Given total power as the constraint and outage probability as an objective function, the proposed scheme possesses good power efficiency better than the equal power allocation. By the ISHDAF scheme and HDAF relay selection strategy, an optimized power allocation for both the source and relay nodes is obtained, as well as an effective reduction of outage probability. In addition, the optimal relay location for maximizing the gain of the proposed algorithm is also investigated and designed. Simulation results show that, in both single relay and multirelay selection systems, some outage probability gains by the proposed scheme can be obtained. In the comparison of the optimized power allocation scheme with the equal power allocation one, nearly 0.1695 gains are obtained in the ISHDAF single relay network at a total power of 2 dB, and about 0.083 gains are obtained in the HDAF relay selection system with 2 relays at a total power of 2 dB.

Fundamentals of differential beamforming

CERN Document Server

Benesty, Jacob; Pan, Chao

2016-01-01

This book provides a systematic study of the fundamental theory and methods of beamforming with differential microphone arrays (DMAs), or differential beamforming in short. It begins with a brief overview of differential beamforming and some popularly used DMA beampatterns such as the dipole, cardioid, hypercardioid, and supercardioid, before providing essential background knowledge on orthogonal functions and orthogonal polynomials, which form the basis of differential beamforming. From a physical perspective, a DMA of a given order is defined as an array that measures the differential acoustic pressure field of that order; such an array has a beampattern in the form of a polynomial whose degree is equal to the DMA order. Therefore, the fundamental and core problem of differential beamforming boils down to the design of beampatterns with orthogonal polynomials. But certain constraints also have to be considered so that the resulting beamformer does not seriously amplify the sensors’ self noise and the mism...

An acousto-optic beamformer

DEFF Research Database (Denmark)

Torras Rosell, Antoni; Barrera Figueroa, Salvador; Jacobsen, Finn

2012-01-01

There is a great variety of beamforming techniques that can be used for localization of sound sources. The differences among them usually lie in the array layout or in the specific signal processing algorithm used to compute the beamforming output. Any beamforming system consists of a finite numb...

Optimal transmit power allocation for MIMO two-way cognitive relay networks with multiple relays using AF strategy

KAUST Repository

Alsharoa, Ahmad M.

2014-02-01

In this letter, we consider a multiple-input multiple-output two-way cognitive radio system under a spectrum sharing scenario, where primary and secondary users operate on the same frequency band. The secondary terminals aims to exchange different messages with each other using multiple relays where each relay employs an amplify-and-forward strategy. The main objective of our work is to maximize the secondary sum rate allowed to share the spectrum with the primary users by respecting a primary user tolerated interference threshold. In this context, we derive an analytical expression of the optimal power allocated to each antenna of the terminals. We then discuss the impact of some system parameters on the performance in the numerical result section. © 2012 IEEE.

Power Allocation Strategies for Fixed-Gain Half-Duplex Amplify-and-Forward Relaying in Nakagami-m Fading

KAUST Repository

Zafar, Ammar

2013-09-01

In this paper, we study power allocation strategies for a fixed-gain amplify-and-forward relay network employing multiple relays. We consider two optimization problems for the relay network: 1) maximizing the end-to-end signalto- noise ratio (SNR) and 2) minimizing the total power consumption while maintaining the end-to-end SNR over a threshold value. We investigate these two problems for two relaying protocols of all-participate (AP) relaying and selective relaying and two cases of feedback to the relays, full and limited. We show that the SNR maximization problem is concave and the power minimization problem is convex for all protocols and feedback cases considered. We obtain closed-form expressions for the two problems in the case of full feedback and solve the problems through convex programming for limited feedback. Numerical results show the benefit of having full feedback at the relays for both optimization problems. However, they also show that feedback overhead can be reduced by having only limited feedback to the relays with only a small degradation in performance.

Robustness Beamforming Algorithms

Directory of Open Access Journals (Sweden)

Sajad Dehghani

2014-04-01

Full Text Available Adaptive beamforming methods are known to degrade in the presence of steering vector and covariance matrix uncertinity. In this paper, a new approach is presented to robust adaptive minimum variance distortionless response beamforming make robust against both uncertainties in steering vector and covariance matrix. This method minimize a optimization problem that contains a quadratic objective function and a quadratic constraint. The optimization problem is nonconvex but is converted to a convex optimization problem in this paper. It is solved by the interior-point method and optimum weight vector to robust beamforming is achieved.

Relay Selection for Cooperative Relaying in Wireless Energy Harvesting Networks

Science.gov (United States)

Zhu, Kaiyan; Wang, Fei; Li, Songsong; Jiang, Fengjiao; Cao, Lijie

2018-01-01

Energy harvesting from the surroundings is a promising solution to provide energy supply and extend the life of wireless sensor networks. Recently, energy harvesting has been shown as an attractive solution to prolong the operation of cooperative networks. In this paper, we propose a relay selection scheme to optimize the amplify-and-forward (AF) cooperative transmission in wireless energy harvesting cooperative networks. The harvesting energy and channel conditions are considered to select the optimal relay as cooperative relay to minimize the outage probability of the system. Simulation results show that our proposed relay selection scheme achieves better outage performance than other strategies.

Beamforming design with proactive interference cancelation in MISO interference channels

Science.gov (United States)

Li, Yang; Tian, Yafei; Yang, Chenyang

2015-12-01

In this paper, we design coordinated beamforming at base stations (BSs) to facilitate interference cancelation at users in interference networks, where each BS is equipped with multiple antennas and each user is with a single antenna. By assuming that each user can select the best decoding strategy to mitigate the interference, either canceling the interference after decoding when it is strong or treating it as noise when it is weak, we optimize the beamforming vectors that maximize the sum rate for the networks under different interference scenarios and find the solutions of beamforming with closed-form expressions. The inherent design principles are then analyzed, and the performance gain over passive interference cancelation is demonstrated through simulations in heterogeneous cellular networks.

Joint Subcarrier Pairing and Resource Allocation for Cognitive Network and Adaptive Relaying Strategy

KAUST Repository

Soury, Hamza

2012-05-01

Recent measurements show that the spectrum is under-utilized by licensed users in wireless communication. Cognitive radio (CR) has been proposed as a suitable solution to manage the inefficient usage of the spectrum and increase coverage area of wireless networks. The concept is based on allowing a group of secondary users (SUs) to share the unused radio spectrum originally owned by the primary user (PUs). The operation of CR should not cause harmful interference to the PUs. In the other hand, relayed transmission increases the coverage and achievable capacity of communication systems and in particular in CR systems. In fact there are many types of cooperative communications, however the two main ones are decode-and-forward (DAF) and amplify-and-forward (AAF). Adaptive relaying scheme is a relaying technique by which the benefits of the amplifying or decode and forward techniques can be achieved by switching the forwarding technique according to the quality of the signal. In this dissertation, we investigate the power allocation for an adaptive relaying protocol (ARP) scheme in cognitive system by maximizing the end-to-end rate and searching the best carriers pairing distribution. The optimization problem is under the interference and power budget constraints. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques, and the consequence of the choice of the pairing strategy.

Individual Channel Estimation in a Diamond Relay Network Using Relay-Assisted Training

Directory of Open Access Journals (Sweden)

Xianwen He

2017-01-01

Full Text Available We consider the training design and channel estimation in the amplify-and-forward (AF diamond relay network. Our strategy is to transmit the source training in time-multiplexing (TM mode while each relay node superimposes its own relay training over the amplified received data signal without bandwidth expansion. The principal challenge is to obtain accurate channel state information (CSI of second-hop link due to the multiaccess interference (MAI and cooperative data interference (CDI. To maintain the orthogonality between data and training, a modified relay-assisted training scheme is proposed to migrate the CDI, where some of the cooperative data at the relay are discarded to accommodate relay training. Meanwhile, a couple of optimal zero-correlation zone (ZCZ relay-assisted sequences are designed to avoid MAI. At the destination node, the received signals from the two relay nodes are combined to achieve spatial diversity and enhanced data reliability. The simulation results are presented to validate the performance of the proposed schemes.

Synthetic Aperture Sequential Beamforming

DEFF Research Database (Denmark)

Kortbek, Jacob; Jensen, Jørgen Arendt; Gammelmark, Kim Løkke

2008-01-01

A synthetic aperture focusing (SAF) technique denoted Synthetic Aperture Sequential Beamforming (SASB) suitable for 2D and 3D imaging is presented. The technique differ from prior art of SAF in the sense that SAF is performed on pre-beamformed data contrary to channel data. The objective is to im......A synthetic aperture focusing (SAF) technique denoted Synthetic Aperture Sequential Beamforming (SASB) suitable for 2D and 3D imaging is presented. The technique differ from prior art of SAF in the sense that SAF is performed on pre-beamformed data contrary to channel data. The objective...... is to improve and obtain a more range independent lateral resolution compared to conventional dynamic receive focusing (DRF) without compromising frame rate. SASB is a two-stage procedure using two separate beamformers. First a set of Bmode image lines using a single focal point in both transmit and receive...... is stored. The second stage applies the focused image lines from the first stage as input data. The SASB method has been investigated using simulations in Field II and by off-line processing of data acquired with a commercial scanner. The performance of SASB with a static image object is compared with DRF...

Highly Reconfigurable Beamformer Stimulus Generator

Science.gov (United States)

Vaviļina, E.; Gaigals, G.

2018-02-01

The present paper proposes a highly reconfigurable beamformer stimulus generator of radar antenna array, which includes three main blocks: settings of antenna array, settings of objects (signal sources) and a beamforming simulator. Following from the configuration of antenna array and object settings, different stimulus can be generated as the input signal for a beamformer. This stimulus generator is developed under a greater concept with two utterly independent paths where one is the stimulus generator and the other is the hardware beamformer. Both paths can be complemented in final and in intermediate steps as well to check and improve system performance. This way the technology development process is promoted by making each of the future hardware steps more substantive. Stimulus generator configuration capabilities and test results are presented proving the application of the stimulus generator for FPGA based beamforming unit development and tuning as an alternative to an actual antenna system.

Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

KAUST Repository

Zafar, Ammar

2013-12-01

This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal-to-noise-ratio (SNR) above a certain peak value and satisfying the peak power constraints at the source and relay nodes. To achieve this objective, an optimal relay selection and power allocation strategy is derived by solving the power minimization problem. Numerical results show that the derived optimal strategy enhances the energy-efficiency as compared to a benchmark scheme in which both the source and the selected relay transmit at peak power. © 2013 IEEE.

Adaptive Beamforming for Medical Ultrasound Imaging

DEFF Research Database (Denmark)

Holfort, Iben Kraglund

This dissertation investigates the application of adaptive beamforming for medical ultrasound imaging. The investigations have been concentrated primarily on the Minimum Variance (MV) beamformer. A broadband implementation of theMV beamformer is described, and simulated data have been used...... to demonstrate the performance. The MV beamformer has been applied to different sets of ultrasound imaging sequences; synthetic aperture ultrasound imaging and plane wave ultrasound imaging. And an approach for applying MV optimized apodization weights on both the transmitting and the receiving apertures...

Highly Reconfigurable Beamformer Stimulus Generator

Directory of Open Access Journals (Sweden)

Vaviļina E.

2018-02-01

Full Text Available The present paper proposes a highly reconfigurable beamformer stimulus generator of radar antenna array, which includes three main blocks: settings of antenna array, settings of objects (signal sources and a beamforming simulator. Following from the configuration of antenna array and object settings, different stimulus can be generated as the input signal for a beamformer. This stimulus generator is developed under a greater concept with two utterly independent paths where one is the stimulus generator and the other is the hardware beamformer. Both paths can be complemented in final and in intermediate steps as well to check and improve system performance. This way the technology development process is promoted by making each of the future hardware steps more substantive. Stimulus generator configuration capabilities and test results are presented proving the application of the stimulus generator for FPGA based beamforming unit development and tuning as an alternative to an actual antenna system.

Multiline 3D beamforming using micro-beamformed datasets for pediatric transesophageal echocardiography

Science.gov (United States)

Bera, D.; Raghunathan, S. B.; Chen, C.; Chen, Z.; Pertijs, M. A. P.; Verweij, M. D.; Daeichin, V.; Vos, H. J.; van der Steen, A. F. W.; de Jong, N.; Bosch, J. G.

2018-04-01

Until now, no matrix transducer has been realized for 3D transesophageal echocardiography (TEE) in pediatric patients. In 3D TEE with a matrix transducer, the biggest challenges are to connect a large number of elements to a standard ultrasound system, and to achieve a high volume rate (>200 Hz). To address these issues, we have recently developed a prototype miniaturized matrix transducer for pediatric patients with micro-beamforming and a small central transmitter. In this paper we propose two multiline parallel 3D beamforming techniques (µBF25 and µBF169) using the micro-beamformed datasets from 25 and 169 transmit events to achieve volume rates of 300 Hz and 44 Hz, respectively. Both the realizations use angle-weighted combination of the neighboring overlapping sub-volumes to avoid artifacts due to sharp intensity changes introduced by parallel beamforming. In simulation, the image quality in terms of the width of the point spread function (PSF), lateral shift invariance and mean clutter level for volumes produced by µBF25 and µBF169 are similar to the idealized beamforming using a conventional single-line acquisition with a fully-sampled matrix transducer (FS4k, 4225 transmit events). For completeness, we also investigated a 9 transmit-scheme (3  ×  3) that allows even higher frame rates but found worse B-mode image quality with our probe. The simulations were experimentally verified by acquiring the µBF datasets from the prototype using a Verasonics V1 research ultrasound system. For both µBF169 and µBF25, the experimental PSFs were similar to the simulated PSFs, but in the experimental PSFs, the clutter level was ~10 dB higher. Results indicate that the proposed multiline 3D beamforming techniques with the prototype matrix transducer are promising candidates for real-time pediatric 3D TEE.

Joint Power Allocation and Beamforming in Amplify-and-Forward Relay Networks under Per-Node Power Constraint

Directory of Open Access Journals (Sweden)

Farzin Azami

2017-01-01

Full Text Available Two-way relay networks (TWRN have been intensively investigated over the past decade due to their ability to enhance the performance assessment of networks in terms of cellular coverage and spectral efficiency. Yet, power control in such systems is a nontrivial issue, particularly in multirelay networks where relays are deployed to ensure a required Quality of Service (QoS. In this paper, we envision to address this critical issue by minimizing the sum-power with respect to per-node power consumption and acceptable users’ rates. To tackle this, we employ a variable transformation to turn the fractional quadratically constrained quadratic problem (QCQP into semidefinite programming (SDP. This algorithm is also extended to a distributed format. Simulation results of deploying 10 relay stations reveal that the total power consumption will decrease to approximately 8 dBW for 6 bps/Hz sum-rate.

Switched diversity strategies for dual-hop relaying systems

KAUST Repository

Gaaloul, Fakhreddine; Alouini, Mohamed-Slim; Radaydeh, Redha M.

2011-01-01

This paper investigates the effect of different switched diversity configurations on the implementation complexity and achieved performance of dual-hop amplify-and-forward (AF) relaying networks. A low-complexity model of the relay station

Opportunistic Relay Selection in Multicast Relay Networks using Compressive Sensing

KAUST Repository

Elkhalil, Khalil

2014-12-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. However, for relay selection algorithms to make a selection decision, channel state information (CSI) from all cooperating relays is usually required at a central node. This requirement poses two important challenges. Firstly, CSI acquisition generates a great deal of feedback overhead (air-time) that could result in significant transmission delays. Secondly, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we introduce a limited feedback relay selection algorithm for a multicast relay network. The proposed algorithm exploits the theory of compressive sensing to first obtain the identity of the “strong” relays with limited feedback. Following that, the CSI of the selected relays is estimated using linear minimum mean square error estimation. To minimize the effect of noise on the fed back CSI, we introduce a back-off strategy that optimally backs-off on the noisy estimated CSI. For a fixed group size, we provide closed form expressions for the scaling law of the maximum equivalent SNR for both Decode and Forward (DF) and Amplify and Forward (AF) cases. Numerical results show that the proposed algorithm drastically reduces the feedback air-time and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback channels.

Relay Architectures for 3GPP LTE-Advanced

Directory of Open Access Journals (Sweden)

Peters StevenW

2009-01-01

Full Text Available The Third Generation Partnership Project's Long Term Evolution-Advanced is considering relaying for cost-effective throughput enhancement and coverage extension. While analog repeaters have been used to enhance coverage in commercial cellular networks, the use of more sophisticated fixed relays is relatively new. The main challenge faced by relay deployments in cellular systems is overcoming the extra interference added by the presence of relays. Most prior work on relaying does not consider interference, however. This paper analyzes the performance of several emerging half-duplex relay strategies in interference-limited cellular systems: one-way, two-way, and shared relays. The performance of each strategy as a function of location, sectoring, and frequency reuse are compared with localized base station coordination. One-way relaying is shown to provide modest gains over single-hop cellular networks in some regimes. Shared relaying is shown to approach the gains of local base station coordination at reduced complexity, while two-way relaying further reduces complexity but only works well when the relay is close to the handset. Frequency reuse of one, where each sector uses the same spectrum, is shown to have the highest network throughput. Simulations with realistic channel models provide performance comparisons that reveal the importance of interference mitigation in multihop cellular networks.

Distributed Antenna Channels with Regenerative Relaying: Relay Selection and Asymptotic Capacity

Directory of Open Access Journals (Sweden)

Aitor del Coso

2007-11-01

Full Text Available Multiple-input-multiple-output (MIMO techniques have been widely proposed as a means to improve capacity and reliability of wireless channels, and have become the most promising technology for next generation networks. However, their practical deployment in current wireless devices is severely affected by antenna correlation, which reduces their impact on performance. One approach to solve this limitation is relaying diversity. In relay channels, a set of N wireless nodes aids a source-destination communication by relaying the source data, thus creating a distributed antenna array with uncorrelated path gains. In this paper, we study this multiple relay channel (MRC following a decode-and-forward (D&F strategy (i.e., regenerative forwarding, and derive its achievable rate under AWGN. A half-duplex constraint on relays is assumed, as well as distributed channel knowledge at both transmitter and receiver sides of the communication. For this channel, we obtain the optimum relay selection algorithm and the optimum power allocation within the network so that the transmission rate is maximized. Likewise, we bound the ergodic performance of the achievable rate and derive its asymptotic behavior in the number of relays. Results show that the achievable rate of regenerative MRC grows as the logarithm of the Lambert W function of the total number of relays, that is, 𝒞=log⁡2(W0(N. Therefore, D&F relaying, cannot achieve the capacity of actual MISO channels.

Efficient high-performance ultrasound beamforming using oversampling

Science.gov (United States)

Freeman, Steven R.; Quick, Marshall K.; Morin, Marc A.; Anderson, R. C.; Desilets, Charles S.; Linnenbrink, Thomas E.; O'Donnell, Matthew

1998-05-01

High-performance and efficient beamforming circuitry is very important in large channel count clinical ultrasound systems. Current state-of-the-art digital systems using multi-bit analog to digital converters (A/Ds) have matured to provide exquisite image quality with moderate levels of integration. A simplified oversampling beamforming architecture has been proposed that may a low integration of delta-sigma A/Ds onto the same chip as digital delay and processing circuitry to form a monolithic ultrasound beamformer. Such a beamformer may enable low-power handheld scanners for high-end systems with very large channel count arrays. This paper presents an oversampling beamformer architecture that generates high-quality images using very simple; digitization, delay, and summing circuits. Additional performance may be obtained with this oversampled system for narrow bandwidth excitations by mixing the RF signal down in frequency to a range where the electronic signal to nose ratio of the delta-sigma A/D is optimized. An oversampled transmit beamformer uses the same delay circuits as receive and eliminates the need for separate transmit function generators.

APES Beamforming Applied to Medical Ultrasound Imaging

DEFF Research Database (Denmark)

Blomberg, Ann E. A.; Holfort, Iben Kraglund; Austeng, Andreas

2009-01-01

Recently, adaptive beamformers have been introduced to medical ultrasound imaging. The primary focus has been on the minimum variance (MV) (or Capon) beamformer. This work investigates an alternative but closely related beamformer, the Amplitude and Phase Estimation (APES) beamformer. APES offers...... added robustness at the expense of a slightly lower resolution. The purpose of this study was to evaluate the performance of the APES beamformer on medical imaging data, since correct amplitude estimation often is just as important as spatial resolution. In our simulations we have used a 3.5 MHz, 96...... element linear transducer array. When imaging two closely spaced point targets, APES displays nearly the same resolution as the MV, and at the same time improved amplitude control. When imaging cysts in speckle, APES offers speckle statistics similar to that of the DAS, without the need for temporal...

Physical-Layer Security of a Buffer-Aided Full-Duplex Relaying System

KAUST Repository

El Shafie, Ahmed

2016-07-07

This letter proposes a novel hybrid half-/full-duplex relaying scheme to enhance the relay channel security. A source node (Alice) communicates with her destination node (Bob) in the presence of a buffer-aided full-duplex relay node (Rooney) and a potential eavesdropper (Eve). Rooney adopts two different relaying, namely randomize-and-forward and decode-andforward relaying strategies, to improve the security of the legitimate system. In the first relaying strategy, Rooney uses a codebook different from that used at Alice. In the second relaying strategy, Rooney and Alice use the same codebooks. In addition, Rooney switches between half-duplex and full-duplex modes to further enhance the security of the legitimate system. The numerical results demonstrate that our proposed scheme achieves a significant average secrecy end-to-end throughput improvement relative to the conventional bufferless full-duplex relaying scheme.

Physical-Layer Security of a Buffer-Aided Full-Duplex Relaying System

KAUST Repository

El Shafie, Ahmed; Salem, Ahmed Sultan; Al-Dhahir, Naofal

2016-01-01

This letter proposes a novel hybrid half-/full-duplex relaying scheme to enhance the relay channel security. A source node (Alice) communicates with her destination node (Bob) in the presence of a buffer-aided full-duplex relay node (Rooney) and a potential eavesdropper (Eve). Rooney adopts two different relaying, namely randomize-and-forward and decode-andforward relaying strategies, to improve the security of the legitimate system. In the first relaying strategy, Rooney uses a codebook different from that used at Alice. In the second relaying strategy, Rooney and Alice use the same codebooks. In addition, Rooney switches between half-duplex and full-duplex modes to further enhance the security of the legitimate system. The numerical results demonstrate that our proposed scheme achieves a significant average secrecy end-to-end throughput improvement relative to the conventional bufferless full-duplex relaying scheme.

Parametric Beamformer for Synthetic Aperture Ultrasound Imaging

DEFF Research Database (Denmark)

Nikolov, Svetoslav; Tomov, Borislav Gueorguiev; Jensen, Jørgen Arendt

2006-01-01

. The beamformer consists of a number of identical beamforming blocks, each processing data from several channels and producing part of the image. A number of these blocks can be accommodated in a modern field-programmable gate array device (FPGA), and a whole synthetic aperture system can be implemented using...... with 255 levels. A beamforming block uses input data from 4 elements and produces a set of 10 lines. Linear interpolation is used to implement sub-sample delays. The VHDL code for the beamformer has been synthesized for a Xilinx V4FX100 speed grade 11 FPGA, where it can operate at a maximum clock frequency...

A Delta-Sigma beamformer with integrated apodization

DEFF Research Database (Denmark)

Tomov, Borislav Gueorguiev; Stuart, Matthias Bo; Hemmsen, Martin Christian

2013-01-01

This paper presents a new design of a discrete time Delta-Sigma (ΔΣ) oversampled ultrasound beamformer which integrates individual channel apodization by means of variable feedback voltage in the Delta-Sigma analog to digital (A/D) converters. The output bit-width of each oversampled A/D converter...... remains the same as in an unmodified one. The outputs of all receiving channels are delayed and summed, and the resulting multi-bit sample stream is filtered and decimated to become an image line. The simplicity of this beamformer allows the production of high-channel-count or very compact beamformers....... The data are acquired using 12-bit flash A/D converters at a sampling rate of 70 MHz, and are then upsampled off-line to 560 MHz for input to the simulated ΔΣ beamformer. The latter generates a B-mode image which is compared to that produced by a digital beamformer that uses 10-bit A/D converters...

Scalable Intersample Interpolation Architecture for High-channel-count Beamformers

DEFF Research Database (Denmark)

Tomov, Borislav Gueorguiev; Nikolov, Svetoslav I; Jensen, Jørgen Arendt

2011-01-01

Modern ultrasound scanners utilize digital beamformers that operate on sampled and quantized echo signals. Timing precision is of essence for achieving good focusing. The direct way to achieve it is through the use of high sampling rates, but that is not economical, so interpolation between echo...... samples is used. This paper presents a beamformer architecture that combines a band-pass filter-based interpolation algorithm with the dynamic delay-and-sum focusing of a digital beamformer. The reduction in the number of multiplications relative to a linear perchannel interpolation and band-pass per......-channel interpolation architecture is respectively 58 % and 75 % beamformer for a 256-channel beamformer using 4-tap filters. The approach allows building high channel count beamformers while maintaining high image quality due to the use of sophisticated intersample interpolation....

Synthetic Aperture Beamformation using the GPU

DEFF Research Database (Denmark)

Hansen, Jens Munk; Schaa, Dana; Jensen, Jørgen Arendt

2011-01-01

A synthetic aperture ultrasound beamformer is implemented for a GPU using the OpenCL framework. The implementation supports beamformation of either RF signals or complex baseband signals. Transmit and receive apodization can be either parametric or dynamic using a fixed F-number, a reference...

Protective relay

International Nuclear Information System (INIS)

Lim, Mu Ji; Jung, Hae Sang

1974-10-01

This book is divided into two chapters, which deals with protective relay. The first chapter deals with the basic knowledge of relay on development of relay, classification of protective relay, rating of protective relay general structure of protective relay, detecting of ground protection, about point of contact, operating relay and trip relaying. The second chapter is about structure and explanation of relay on classification by structure such as motor type and moving-coil type, explanation of other relays over current relay, over voltage relay, short voltage relay, relay for power, relay for direction, test of over voltage relay, test of short voltage relay and test of directional circuit relay.

Robust regularized least-squares beamforming approach to signal estimation

KAUST Repository

Suliman, Mohamed Abdalla Elhag

2017-05-12

In this paper, we address the problem of robust adaptive beamforming of signals received by a linear array. The challenge associated with the beamforming problem is twofold. Firstly, the process requires the inversion of the usually ill-conditioned covariance matrix of the received signals. Secondly, the steering vector pertaining to the direction of arrival of the signal of interest is not known precisely. To tackle these two challenges, the standard capon beamformer is manipulated to a form where the beamformer output is obtained as a scaled version of the inner product of two vectors. The two vectors are linearly related to the steering vector and the received signal snapshot, respectively. The linear operator, in both cases, is the square root of the covariance matrix. A regularized least-squares (RLS) approach is proposed to estimate these two vectors and to provide robustness without exploiting prior information. Simulation results show that the RLS beamformer using the proposed regularization algorithm outperforms state-of-the-art beamforming algorithms, as well as another RLS beamformers using a standard regularization approaches.

Secure relay selection based on learning with negative externality in wireless networks

Science.gov (United States)

Zhao, Caidan; Xiao, Liang; Kang, Shan; Chen, Guiquan; Li, Yunzhou; Huang, Lianfen

2013-12-01

In this paper, we formulate relay selection into a Chinese restaurant game. A secure relay selection strategy is proposed for a wireless network, where multiple source nodes send messages to their destination nodes via several relay nodes, which have different processing and transmission capabilities as well as security properties. The relay selection utilizes a learning-based algorithm for the source nodes to reach their best responses in the Chinese restaurant game. In particular, the relay selection takes into account the negative externality of relay sharing among the source nodes, which learn the capabilities and security properties of relay nodes according to the current signals and the signal history. Simulation results show that this strategy improves the user utility and the overall security performance in wireless networks. In addition, the relay strategy is robust against the signal errors and deviations of some user from the desired actions.

Adaptive Beamforming Based on Complex Quaternion Processes

Directory of Open Access Journals (Sweden)

Jian-wu Tao

2014-01-01

Full Text Available Motivated by the benefits of array signal processing in quaternion domain, we investigate the problem of adaptive beamforming based on complex quaternion processes in this paper. First, a complex quaternion least-mean squares (CQLMS algorithm is proposed and its performance is analyzed. The CQLMS algorithm is suitable for adaptive beamforming of vector-sensor array. The weight vector update of CQLMS algorithm is derived based on the complex gradient, leading to lower computational complexity. Because the complex quaternion can exhibit the orthogonal structure of an electromagnetic vector-sensor in a natural way, a complex quaternion model in time domain is provided for a 3-component vector-sensor array. And the normalized adaptive beamformer using CQLMS is presented. Finally, simulation results are given to validate the performance of the proposed adaptive beamformer.

Relay selection from an effective capacity perspective

KAUST Repository

Yang, Yuli; Ma, Hao; Aï ssa, Sonia

2013-01-01

proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between

Single-station 6C beamforming

Science.gov (United States)

Nakata, N.; Hadziioannou, C.; Igel, H.

2017-12-01

Six-component measurements of seismic ground motion provide a unique opportunity to identify and decompose seismic wavefields into different wave types and incoming azimuths, as well as estimate structural information (e.g., phase velocity). By using the relationship between the transverse component and vertical rotational motion for Love waves, we can find the incident azimuth of the wave and the phase velocity. Therefore, when we scan the entire range of azimuth and slownesses, we can process the seismic waves in a similar way to conventional beamforming processing, without using a station array. To further improve the beam resolution, we use the distribution of amplitude ratio between translational and rotational motions at each time sample. With this beamforming, we decompose multiple incoming waves by azimuth and phase velocity using only one station. We demonstrate this technique using the data observed at Wettzell (vertical rotational motion and 3C translational motions). The beamforming results are encouraging to extract phase velocity at the location of the station, apply to oceanic microseism, and to identify complicated SH wave arrivals. We also discuss single-station beamforming using other components (vertical translational and horizontal rotational components). For future work, we need to understand the resolution limit of this technique, suitable length of time windows, and sensitivity to weak motion.

Chiral relay: a novel strategy for the control and amplification of enantioselectivity in chiral Lewis acid promoted reactions.

Science.gov (United States)

Corminboeuf, Olivier; Quaranta, Laura; Renaud, Philippe; Liu, Mei; Jasperse, Craig P; Sibi, Mukund P

2003-01-03

Chiral Lewis acid catalysis has emerged as one of the premiere method to control stereochemistry. Much effort has gone into the design of superior ligands with increasing steric extension to shield distant reactive sites. We report here an alternative and complementary approach based on a "chiral relay". This strategy focuses on the improved design of achiral templates which may relay and amplify the stereochemistry from ligands. The essence of this strategy is that the chiral Lewis acid would effectively convert an achiral template into a chiral non-racemic template. This approach combines the advantages of enantioselective catalysis (substoichiometric amount of the chiral inducer) with the ones of chiral auxiliary control (efficient and predictable stereocontrol).

A PSF-Shape-Based Beamforming Strategy for Robust 2D Motion Estimation in Ultrafast Data

Directory of Open Access Journals (Sweden)

Anne E. C. M. Saris

2018-03-01

Full Text Available This paper presents a framework for motion estimation in ultrafast ultrasound data. It describes a novel approach for determining the sampling grid for ultrafast data based on the system’s point-spread-function (PSF. As a consequence, the cross-correlation functions (CCF used in the speckle tracking (ST algorithm will have circular-shaped peaks, which can be interpolated using a 2D interpolation method to estimate subsample displacements. Carotid artery wall motion and parabolic blood flow simulations together with rotating disk experiments using a Verasonics Vantage 256 are used for performance evaluation. Zero-degree plane wave data were acquired using an ATL L5-12 (fc = 9 MHz transducer for a range of pulse repetition frequencies (PRFs, resulting in 0–600 µm inter-frame displacements. The proposed methodology was compared to data beamformed on a conventionally spaced grid, combined with the commonly used 1D parabolic interpolation. The PSF-shape-based beamforming grid combined with 2D cubic interpolation showed the most accurate and stable performance with respect to the full range of inter-frame displacements, both for the assessment of blood flow and vessel wall dynamics. The proposed methodology can be used as a protocolled way to beamform ultrafast data and obtain accurate estimates of tissue motion.

Low complexity symbol-wise beamforming for MIMO-OFDM systems

KAUST Repository

Lee, Hyun Ho

2011-12-01

In this paper, we consider a low complexity symbol-wise beamforming for MIMO-OFDM systems. We propose a non-iterative algorithm for the symbol-wise beamforming, which can provide the performance approaching that of the conventional symbol-wise beamforming based on the iterative algorithm. We demonstrate that our proposed scheme can reduce the computational complexity significantly. From our simulation results, it is evident that our proposed scheme leads to a negligible performance loss compared to the conventional symbol-wise beamforming regardless of spatial correlation or presence of co-channel interference. © 2011 IEEE.

MVDR Algorithm Based on Estimated Diagonal Loading for Beamforming

Directory of Open Access Journals (Sweden)

Yuteng Xiao

2017-01-01

Full Text Available Beamforming algorithm is widely used in many signal processing fields. At present, the typical beamforming algorithm is MVDR (Minimum Variance Distortionless Response. However, the performance of MVDR algorithm relies on the accurate covariance matrix. The MVDR algorithm declines dramatically with the inaccurate covariance matrix. To solve the problem, studying the beamforming array signal model and beamforming MVDR algorithm, we improve MVDR algorithm based on estimated diagonal loading for beamforming. MVDR optimization model based on diagonal loading compensation is established and the interval of the diagonal loading compensation value is deduced on the basis of the matrix theory. The optimal diagonal loading value in the interval is also determined through the experimental method. The experimental results show that the algorithm compared with existing algorithms is practical and effective.

Adaptive Beamforming using the Reconfigurable Montium TP

NARCIS (Netherlands)

van de Burgwal, M.D.; Rovers, K.C.; Blom, K.C.H.; Kokkeler, Andre B.J.; Smit, Gerardus Johannes Maria; López, S.

2010-01-01

Until a decade ago, the concept of phased array beamforming was mainly implemented with mechanical or analog solutions. Today, digital hardware has become powerful enough to perform the massive number of operations required for real-time digital beamforming. While more and more applications are

Optimal beamforming in MIMO systems with HPA nonlinearity

KAUST Repository

Qi, Jian

2010-09-01

In this paper, multiple-input multiple-output (MIMO) transmit beamforming (TB) systems under the consideration of nonlinear high-power amplifiers (HPAs) are investigated. The optimal beamforming scheme, with the optimal beamforming weight vector and combining vector, is proposed for MIMO systems with HPA nonlinearity. The performance of the proposed MIMO beamforming scheme in the presence of HPA nonlinearity is evaluated in terms of average symbol error probability (SEP), outage probability and system capacity, considering transmission over uncorrelated quasi-static frequency-flat Rayleigh fading channels. Numerical results are provided and show the effects of several system parameters, namely, parameters of nonlinear HPA, numbers of transmit and receive antennas, and modulation order of phase-shift keying (PSK), on performance. ©2010 IEEE.

Optimal beamforming in MIMO systems with HPA nonlinearity

KAUST Repository

Qi, Jian; Aissa, Sonia

2010-01-01

In this paper, multiple-input multiple-output (MIMO) transmit beamforming (TB) systems under the consideration of nonlinear high-power amplifiers (HPAs) are investigated. The optimal beamforming scheme, with the optimal beamforming weight vector and combining vector, is proposed for MIMO systems with HPA nonlinearity. The performance of the proposed MIMO beamforming scheme in the presence of HPA nonlinearity is evaluated in terms of average symbol error probability (SEP), outage probability and system capacity, considering transmission over uncorrelated quasi-static frequency-flat Rayleigh fading channels. Numerical results are provided and show the effects of several system parameters, namely, parameters of nonlinear HPA, numbers of transmit and receive antennas, and modulation order of phase-shift keying (PSK), on performance. ©2010 IEEE.

Optimal beamforming in ultrasound using the ideal observer.

Science.gov (United States)

Abbey, Craig K; Nguyen, Nghia Q; Insana, Michael F

2010-08-01

Beamforming of received pulse-echo data generally involves the compression of signals from multiple channels within an aperture. This compression is irreversible, and therefore allows the possibility that information relevant for performing a diagnostic task is irretrievably lost. The purpose of this study was to evaluate information transfer in beamforming using a previously developed ideal observer model to quantify diagnostic information relevant to performing a task. We describe an elaborated statistical model of image formation for fixed-focus transmission and single-channel reception within a moving aperture, and we use this model on a panel of tasks related to breast sonography to evaluate receive-beamforming approaches that optimize the transfer of information. Under the assumption that acquisition noise is well described as an additive wide-band Gaussian white-noise process, we show that signal compression across receive-aperture channels after a 2-D matched-filtering operation results in no loss of diagnostic information. Across tasks, the matched-filter beamformer results in more information than standard delay-and-sum beamforming in the subsequent radio-frequency signal by a factor of two. We also show that for this matched filter, 68% of the information gain can be attributed to the phase of the matched-filter and 21% can be attributed to the amplitude. A 1-D matched filtering along axial lines shows no advantage over delay-andsum, suggesting an important role for incorporating correlations across different aperture windows in beamforming. We also show that a post-compression processing before the computation of an envelope is necessary to pass the diagnostic information in the beamformed radio-frequency signal to the final envelope image.

Effective and versatile software beamformation toolbox

DEFF Research Database (Denmark)

Kortbek, Jacob; Nikolov, Svetoslav; Jensen, Jørgen Arendt

2007-01-01

Delay-and-sum array beamforming is an essential part of signal processing in ultrasound imaging. Although the principles are simple, there are many implementation details to consider for obtaining a reliable and computational efficient beamforming. Different methods for calculation of time......-delays are used for different waveforms. Various inter-sample interpolation schemes such as FIR-filtering, polynomial, and spline interpolation can be chosen. Apodization can be any preferred window function of fixed size applied on the channel signals or it can be dynamic with an expanding and contracting...... seconds using a transducer of 128 elements, dynamic apodization and 3rd order polynomial interpolation. This is a decrease in computation time of at least a factor of 15 compared to an implementation directly in MATLAB of a similar beamformer....

Photonic Beamformer Model Based on Analog Fiber-Optic Links’ Components

International Nuclear Information System (INIS)

Volkov, V A; Gordeev, D A; Ivanov, S I; Lavrov, A P; Saenko, I I

2016-01-01

The model of photonic beamformer for wideband microwave phased array antenna is investigated. The main features of the photonic beamformer model based on true-time-delay technique, DWDM technology and fiber chromatic dispersion are briefly analyzed. The performance characteristics of the key components of photonic beamformer for phased array antenna in the receive mode are examined. The beamformer model composed of the components available on the market of fiber-optic analog communication links is designed and tentatively investigated. Experimental demonstration of the designed model beamforming features includes actual measurement of 5-element microwave linear array antenna far-field patterns in 6-16 GHz frequency range for antenna pattern steering up to 40°. The results of experimental testing show good accordance with the calculation estimates. (paper)

Near optimal power allocation algorithm for OFDM-based cognitive using adaptive relaying strategy

KAUST Repository

Soury, Hamza; Bader, Faouzi; Shaat, Musbah M R; Alouini, Mohamed-Slim

2012-01-01

Relayed transmission increases the coverage and achievable capacity of communication systems. Adaptive relaying scheme is a relaying technique by which the benefits of the amplifying or decode and forward techniques can be achieved by switching the forwarding technique according to the quality of the signal. A cognitive Orthogonal Frequency-Division Multiplexing (OFDM) based adaptive relaying protocol is considered in this paper. The objective is to maximize the capacity of the cognitive radio system while ensuring that the interference introduced to the primary user is below the tolerated limit. A Near optimal power allocation in the source and the relay is presented for two pairing techniques such that the matching and random pairing. The simulation results confirm the efficiency of the proposed adaptive relaying protocol, and the consequence of choice of pairing technique. © 2012 ICST.

Beamforming design of sum rate optimization for MU-MISO scenario

Directory of Open Access Journals (Sweden)

ZHAO Pu

2015-02-01

Full Text Available This paper investigates the beamforming design based on perfect channel state information (CSI in a multi-user downlink network.The base station (BS is equipped with multiple antennas while each user is equipped with one antenna.The BS will communicate with users through transmit beamforming technology.This paper maximizes the sum rate of all users with the constraint of transmitting power.The object function is complex and non-convex which would bring difficulties to solve this problem.This article proposes a beamforming scheme based on zero-forcing criterion.Based on this method,the original problem will be divided into two sub-problems which can be solved respectively.The simulation results suggest that the proposed beamforming scheme achieves better performance compared with the traditional leakage based beamforming scheme.

Relay selection from an effective capacity perspective

KAUST Repository

Yang, Yuli

2013-09-01

In this work, we consider a cooperative network where multiple relay nodes having different modulation capabilities assist the end-to-end communication between a source and its destination. Firstly, we evaluate the effective capacity (EC) performance of the network under study. According to the analysis, an EC-based relay selection criterion is proposed. Based on the proposed selection rule and half-duplex decode-and-forward protocol, the activated relays cooperatively help with the packet transmission from the source. At the destination, packet combining is taken into account to improve the quality of service. Compared to the popular scheme, opportunistic relay selection, numerical results are provided to prove the validity and advantages of our proposed scheme in certain scenarios. Moreover, the analysis presented herein offers a convenient tool to the relaying transmission design, specifically on which relay selection scheme should be used as well as how to choose the receiving strategy between with and without packet combining at the destination. © 2013 IEEE.

Plane Wave Medical Ultrasound Imaging Using Adaptive Beamforming

DEFF Research Database (Denmark)

Holfort, Iben Kraglund; Gran, Fredrik; Jensen, Jørgen Arendt

2008-01-01

In this paper, the adaptive, minimum variance (MV) beamformer is applied to medical ultrasound imaging. The Significant resolution and contrast gain provided by the adaptive, minimum variance (MV) beamformer, introduces the possibility of plane wave (PW) ultrasound imaging. Data is obtained using...

Outage Probability versus Fairness Trade-off in Opportunistic Relay Selection with Outdated CSI

Directory of Open Access Journals (Sweden)

Vicario JoseLopez

2009-01-01

Full Text Available We analyze the existing trade-offs in terms of system performance versus fairness of a cooperative system based on opportunistic relay selection (ORS and with outdated channel state information (CSI. In particular, system performance is analytically evaluated in terms of outage probability, and the fairness behavior is assessed based on the power consumption at the different relays. In order to improve the fairness behavior of ORS while keeping the selection diversity gain, we propose a relay selection mechanism where the relay with the highest normalized signal-to-noise ratio (SNR is selected for relaying the source's information. The proposed strategy is compared with existing relay selection strategies by adopting a novel graphical representation inspired by expected profit versus risk plots used in modern portfolio theory. As shown in the paper, this strategy allows operating the system in more favorable points of the outage versus fairness region.

Relay selection in cooperative communication systems over continuous time-varying fading channel

Directory of Open Access Journals (Sweden)

Ke Geng

2017-02-01

Full Text Available In this paper, we study relay selection under outdated channel state information (CSI in a decode-and-forward (DF cooperative system. Unlike previous researches on cooperative communication under outdated CSI, we consider that the channel varies continuously over time, i.e., the channel not only changes between relay selection and data transmission but also changes during data transmission. Thus the level of accuracy of the CSI used in relay selection degrades with data transmission. We first evaluate the packet error rate (PER of the cooperative system under continuous time-varying fading channel, and find that the PER performance deteriorates more seriously under continuous time-varying fading channel than when the channel is assumed to be constant during data transmission. Then, we propose a repeated relay selection (RRS strategy to improve the PER performance, in which the forwarded data is divided into multiple segments and relay is reselected before the transmission of each segment based on the updated CSI. Finally, we propose a combined relay selection (CRS strategy which takes advantage of three different relay selection strategies to further mitigate the impact of outdated CSI.

Smart Antenna UKM Testbed for Digital Beamforming System

Directory of Open Access Journals (Sweden)

2009-03-01

Full Text Available A new design of smart antenna testbed developed at UKM for digital beamforming purpose is proposed. The smart antenna UKM testbed developed based on modular design employing two novel designs of L-probe fed inverted hybrid E-H (LIEH array antenna and software reconfigurable digital beamforming system (DBS. The antenna is developed based on using the novel LIEH microstrip patch element design arranged into 4×1 uniform linear array antenna. An interface board is designed to interface to the ADC board with the RF front-end receiver. The modular concept of the system provides the capability to test the antenna hardware, beamforming unit, and beamforming algorithm in an independent manner, thus allowing the smart antenna system to be developed and tested in parallel, hence reduces the design time. The DBS was developed using a high-performance TMS320C6711TM floating-point DSP board and a 4-channel RF front-end receiver developed in-house. An interface board is designed to interface to the ADC board with the RF front-end receiver. A four-element receiving array testbed at 1.88–2.22 GHz frequency is constructed, and digital beamforming on this testbed is successfully demonstrated.

An improved minimum variance beamforming applied to plane-wave imaging in medical ultrasound

DEFF Research Database (Denmark)

Deylami, Ali Mohades; Asl, Babak Mohammadzadeh; Jensen, Jørgen Arendt

2016-01-01

Minimum variance beamformer (MVB) is an adaptive beamformer which provides images with higher resolution and contrast in comparison with non-adaptive beamformers like delay and sum (DAS). It finds weight vector of beamformer by minimizing output power while keeping the desired signal unchanged. We...

Fourier beamformation of multistatic synthetic aperture ultrasound imaging

DEFF Research Database (Denmark)

Moghimirad, Elahe; Villagómez Hoyos, Carlos Armando; Mahloojifar, Ali

2015-01-01

A new Fourier beamformation (FB) algorithm is presented for multistatic synthetic aperture ultrasound imaging. It can reduce the number of computations by a factor of 20 compared to conventional Delay-and-Sum (DAS) beamformers. The concept is based on the wavenumber algorithm from radar and sonar...

Synthetic aperture flow imaging using dual stage beamforming

DEFF Research Database (Denmark)

Li, Ye; Jensen, Jørgen Arendt

2013-01-01

A method for synthetic aperture flow imaging using dual stage beamforming has been developed. The main motivation is to increase the frame rate and still maintain a beamforming quality sufficient for flow estimation that is possible to implement in a commercial scanner. This method can generate...

Double Minimum Variance Beamforming Method to Enhance Photoacoustic Imaging

OpenAIRE

Paridar, Roya; Mozaffarzadeh, Moein; Nasiriavanaki, Mohammadreza; Orooji, Mahdi

2018-01-01

One of the common algorithms used to reconstruct photoacoustic (PA) images is the non-adaptive Delay-and-Sum (DAS) beamformer. However, the quality of the reconstructed PA images obtained by DAS is not satisfying due to its high level of sidelobes and wide mainlobe. In contrast, adaptive beamformers, such as minimum variance (MV), result in an improved image compared to DAS. In this paper, a novel beamforming method, called Double MV (D-MV) is proposed to enhance the image quality compared to...

Capacity Bounds and Mapping Design for Binary Symmetric Relay Channels

Directory of Open Access Journals (Sweden)

Majid Nasiri Khormuji

2012-12-01

Full Text Available Capacity bounds for a three-node binary symmetric relay channel with orthogonal components at the destination are studied. The cut-set upper bound and the rates achievable using decode-and-forward (DF, partial DF and compress-and-forward (CF relaying are first evaluated. Then relaying strategies with finite memory-length are considered. An efficient algorithm for optimizing the relay functions is presented. The Boolean Fourier transform is then employed to unveil the structure of the optimized mappings. Interestingly, the optimized relay functions exhibit a simple structure. Numerical results illustrate that the rates achieved using the optimized low-dimensional functions are either comparable to those achieved by CF or superior to those achieved by DF relaying. In particular, the optimized low-dimensional relaying scheme can improve on DF relaying when the quality of the source-relay link is worse than or comparable to that of other links.

FPGA implementation of adaptive beamforming in hearing aids.

Science.gov (United States)

Samtani, Kartik; Thomas, Jobin; Varma, G Abhinav; Sumam, David S; Deepu, S P

2017-07-01

Beamforming is a spatial filtering technique used in hearing aids to improve target sound reception by reducing interference from other directions. In this paper we propose improvements in an existing architecture present for two omnidirectional microphone array based adaptive beamforming for hearing aid applications and implement the same on Xilinx Artix 7 FPGA using VHDL coding and Xilinx Vivado ® 2015.2. The nulls are introduced in particular directions by combination of two fixed polar patterns. This combination can be adaptively controlled to steer the null in the direction of noise. The beamform patterns and improvements in SNR values obtained from experiments in a conference room environment are analyzed.

Robust regularized least-squares beamforming approach to signal estimation

KAUST Repository

Suliman, Mohamed Abdalla Elhag; Ballal, Tarig; Al-Naffouri, Tareq Y.

2017-01-01

In this paper, we address the problem of robust adaptive beamforming of signals received by a linear array. The challenge associated with the beamforming problem is twofold. Firstly, the process requires the inversion of the usually ill

Relay-aided multi-cell broadcasting with random network coding

DEFF Research Database (Denmark)

Lu, Lu; Sun, Fan; Xiao, Ming

2010-01-01

We investigate a relay-aided multi-cell broadcasting system using random network codes, where the focus is on devising efficient scheduling algorithms between relay and base stations. Two scheduling algorithms are proposed based on different feedback strategies; namely, a one-step scheduling...

Pulse Splitting for Harmonic Beamforming in Time-Modulated Linear Arrays

Directory of Open Access Journals (Sweden)

Lorenzo Poli

2014-01-01

Full Text Available A novel strategy for harmonic beamforming in time-modulated linear arrays is proposed. The pulse splitting technique is exploited to simultaneously generate two harmonic patterns, one at the central frequency and another at a preselected harmonic of arbitrary order, while controlling the maximum level of the remaining sideband radiations. An optimization strategy based on the particle swarm optimizer is developed in order to determine the optimal parameters describing the pulse sequence used to modulate the excitation weights of the array elements. Representative numerical results are reported and discussed to point out potentialities and limitations of the proposed approach.

A performance analysis in AF full duplex relay selection network

Science.gov (United States)

Ngoc, Long Nguyen; Hong, Nhu Nguyen; Loan, Nguyen Thi Phuong; Kieu, Tam Nguyen; Voznak, Miroslav; Zdralek, Jaroslav

2018-04-01

This paper studies on the relaying selective matter in amplify-and-forward (AF) cooperation communication with full-duplex (FD) activity. Various relay choice models supposing the present of different instant information are investigated. We examine a maximal relaying choice that optimizes the instant FD channel capacity and asks for global channel state information (CSI) as well as partial CSI learning. To make comparison easy, accurate outage probability clauses and asymptote form of these strategies that give a diversity rank are extracted. From that, we can see clearly that the number of relays, noise factor, the transmittance coefficient as well as the information transfer power had impacted on their performance. Besides, the optimal relay selection (ORS) model can promote than that of the partial relay selection (PRS) model.

New perspective on single-radiator multiple-port antennas for adaptive beamforming applications.

Science.gov (United States)

Byun, Gangil; Choo, Hosung

2017-01-01

One of the most challenging problems in recent antenna engineering fields is to achieve highly reliable beamforming capabilities in an extremely restricted space of small handheld devices. In this paper, we introduce a new perspective on single-radiator multiple-port (SRMP) antenna to alter the traditional approach of multiple-antenna arrays for improving beamforming performances with reduced aperture sizes. The major contribution of this paper is to demonstrate the beamforming capability of the SRMP antenna for use as an extremely miniaturized front-end component in more sophisticated beamforming applications. To examine the beamforming capability, the radiation properties and the array factor of the SRMP antenna are theoretically formulated for electromagnetic characterization and are used as complex weights to form adaptive array patterns. Then, its fundamental performance limits are rigorously explored through enumerative studies by varying the dielectric constant of the substrate, and field tests are conducted using a beamforming hardware to confirm the feasibility. The results demonstrate that the new perspective of the SRMP antenna allows for improved beamforming performances with the ability of maintaining consistently smaller aperture sizes compared to the traditional multiple-antenna arrays.

New perspective on single-radiator multiple-port antennas for adaptive beamforming applications.

Directory of Open Access Journals (Sweden)

Gangil Byun

Full Text Available One of the most challenging problems in recent antenna engineering fields is to achieve highly reliable beamforming capabilities in an extremely restricted space of small handheld devices. In this paper, we introduce a new perspective on single-radiator multiple-port (SRMP antenna to alter the traditional approach of multiple-antenna arrays for improving beamforming performances with reduced aperture sizes. The major contribution of this paper is to demonstrate the beamforming capability of the SRMP antenna for use as an extremely miniaturized front-end component in more sophisticated beamforming applications. To examine the beamforming capability, the radiation properties and the array factor of the SRMP antenna are theoretically formulated for electromagnetic characterization and are used as complex weights to form adaptive array patterns. Then, its fundamental performance limits are rigorously explored through enumerative studies by varying the dielectric constant of the substrate, and field tests are conducted using a beamforming hardware to confirm the feasibility. The results demonstrate that the new perspective of the SRMP antenna allows for improved beamforming performances with the ability of maintaining consistently smaller aperture sizes compared to the traditional multiple-antenna arrays.

Superimposed Training-Based Channel Estimation for MIMO Relay Networks

Directory of Open Access Journals (Sweden)

Xiaoyan Xu

2012-01-01

Full Text Available We introduce the superimposed training strategy into the multiple-input multiple-output (MIMO amplify-and-forward (AF one-way relay network (OWRN to perform the individual channel estimation at the destination. Through the superposition of a group of additional training vectors at the relay subject to power allocation, the separated estimates of the source-relay and relay-destination channels can be obtained directly at the destination, and the accordance with the two-hop AF strategy can be guaranteed at the same time. The closed-form Bayesian Cramér-Rao lower bound (CRLB is derived for the estimation of two sets of flat-fading MIMO channel under random channel parameters and further exploited to design the optimal training vectors. A specific suboptimal channel estimation algorithm is applied in the MIMO AF OWRN using the optimal training sequences, and the normalized mean square error performance for the estimation is provided to verify the Bayesian CRLB results.

Relay-Assisted Primary and Secondary Transmissions in Cognitive Radio Networks

KAUST Repository

Shafie, Ahmed El

2016-09-27

We assume a set of cognitive relay nodes that assists both primary and secondary transmissions in a time-slotted cognitive radio networks. To regulate the channel access of the various nodes in the network, we propose an overlapped spectrum sensing strategy for channel sensing, where the secondary source node senses the channel from the beginning of the time slot and the cognitive relay nodes sense the channel for double the sensing time used by the secondary source node to detect the activities of both the primary and secondary source nodes. Hence, the secondary source node has an intrinsic priority over the relay nodes. The relay nodes help both the primary user and the secondary user to deliver their unsuccessfully decoded packets at their destinations. In a given time slot, the scheduled relay node for data transmission starts its transmission when both the primary and secondary users are sensed to be inactive (i.e. have no data to transmit). We propose two optimization-based formulations with quality-of-service (QoS) constraints involving average queueing delay and average service rate requirements. We investigate both cases of perfect and imperfect spectrum sensing. To further enhance the users\\' QoS requirements, we propose three packet decoding strategies at the relay nodes and compare their performance. We derive an upper bound on the secondary queue average service rate to determine which decoding strategy can achieve that bound. Our numerical results show the benefits of relaying and its ability to enhance the performance of both the primary and secondary users. Moreover, the performance of the proposed schemes is close to the derived upper bound.

Switched diversity strategies for dual-hop amplify-and-forward relaying systems

KAUST Repository

Gaaloul, Fakhreddine

2012-01-01

This study investigates different receive single-branch switch-based diversity schemes for dual-hop amplify-and-forward relaying networks. Specifically, three receive processing algorithms are adopted, in which the receive branch is selected using the arbitrary selection algorithm, the switching algorithm, or the switching algorithm with post-examining best branch selection. The identification of the receive branch is carried out for two different system models. For the first model, a single-antenna relaying station is used in conjunction with a multiple-antenna transceiver, where the processing is performed independently of the first hop-fading conditions. The second model suggests the use of parallel deployment of single-antenna relays to transfer information from a multiple-antenna transmitter to a single-antenna receiver, where the active relaying station is determined based on the pre-combining end-to-end fading conditions. Performance comparisons for various transmission scenarios on the first hop are presented using new formulations for the statistics of the combined signal-to-noise ratio. Simulation results are also provided to validate the mathematical development and to verify the numerical computations. © 2012 The Institution of Engineering and Technology.

Iterative Minimum Variance Beamformer with Low Complexity for Medical Ultrasound Imaging.

Science.gov (United States)

Deylami, Ali Mohades; Asl, Babak Mohammadzadeh

2018-06-04

Minimum variance beamformer (MVB) improves the resolution and contrast of medical ultrasound images compared with delay and sum (DAS) beamformer. The weight vector of this beamformer should be calculated for each imaging point independently, with a cost of increasing computational complexity. The large number of necessary calculations limits this beamformer to application in real-time systems. A beamformer is proposed based on the MVB with lower computational complexity while preserving its advantages. This beamformer avoids matrix inversion, which is the most complex part of the MVB, by solving the optimization problem iteratively. The received signals from two imaging points close together do not vary much in medical ultrasound imaging. Therefore, using the previously optimized weight vector for one point as initial weight vector for the new neighboring point can improve the convergence speed and decrease the computational complexity. The proposed method was applied on several data sets, and it has been shown that the method can regenerate the results obtained by the MVB while the order of complexity is decreased from O(L 3 ) to O(L 2 ). Copyright © 2018 World Federation for Ultrasound in Medicine and Biology. Published by Elsevier Inc. All rights reserved.

Low complexity non-iterative coordinated beamforming in 2-user broadcast channels

KAUST Repository

Park, Kihong

2010-10-01

We propose a new non-iterative coordinated beamforming scheme to obtain full multiplexing gain in 2-user MIMO systems. In order to find the beamforming and combining matrices, we solve a generalized eigenvector problem and describe how to find generalized eigenvectors according to the Gaussian broadcast channels. Selected simulation results show that the proposed method yields the same sum-rate performance as the iterative coordinated beamforming method, while maintaining lower complexity by non-iterative computation of the beamforming and combining matrices. We also show that the proposed method can easily exploit selective gain by choosing the best combination of generalized eigenvectors. © 2006 IEEE.

Low complexity non-iterative coordinated beamforming in 2-user broadcast channels

KAUST Repository

Park, Kihong; Ko, Youngchai; Alouini, Mohamed-Slim

2010-01-01

We propose a new non-iterative coordinated beamforming scheme to obtain full multiplexing gain in 2-user MIMO systems. In order to find the beamforming and combining matrices, we solve a generalized eigenvector problem and describe how to find generalized eigenvectors according to the Gaussian broadcast channels. Selected simulation results show that the proposed method yields the same sum-rate performance as the iterative coordinated beamforming method, while maintaining lower complexity by non-iterative computation of the beamforming and combining matrices. We also show that the proposed method can easily exploit selective gain by choosing the best combination of generalized eigenvectors. © 2006 IEEE.

Analog Gradient Beamformer for a Wireless Ultrasound Scanner

DEFF Research Database (Denmark)

di Ianni, Tommaso; Hemmsen, Martin Christian; Bagge, Jan Peter

2016-01-01

This paper presents a novel beamformer architecture for a low-cost receiver front-end, and investigates if the image quality can be maintained. The system is oriented to the development of a hand-held wireless ultrasound probe based on Synthetic Aperture Sequential Beamforming, and has the advant......This paper presents a novel beamformer architecture for a low-cost receiver front-end, and investigates if the image quality can be maintained. The system is oriented to the development of a hand-held wireless ultrasound probe based on Synthetic Aperture Sequential Beamforming, and has...... the advantage of effectively reducing circuit complexity and power dissipation. The array of transducers is divided into sub-apertures, in which the signals from the single channels are aligned through a network of cascaded gradient delays, and summed in the analog domain before A/D conversion. The delay values...... are quantized to simplify the shifting unit, and a single A/D converter is needed for each sub-aperture yielding a compact, low-power architecture that can be integrated in a single chip. A simulation study was performed using a 3.75 MHz convex array, and the point spread function (PSF) for different...

Secrecy Capacity of a Class of Orthogonal Relay Eavesdropper Channels

Directory of Open Access Journals (Sweden)

Aggarwal Vaneet

2009-01-01

Full Text Available The secrecy capacity of relay channels with orthogonal components is studied in the presence of an additional passive eavesdropper node. The relay and destination receive signals from the source on two orthogonal channels such that the destination also receives transmissions from the relay on its channel. The eavesdropper can overhear either one or both of the orthogonal channels. Inner and outer bounds on the secrecy capacity are developed for both the discrete memoryless and the Gaussian channel models. For the discrete memoryless case, the secrecy capacity is shown to be achieved by a partial decode-and-forward (PDF scheme when the eavesdropper can overhear only one of the two orthogonal channels. Two new outer bounds are presented for the Gaussian model using recent capacity results for a Gaussian multiantenna point-to-point channel with a multiantenna eavesdropper. The outer bounds are shown to be tight for two subclasses of channels. The first subclass is one in which the source and relay are clustered, and the eavesdropper receives signals only on the channel from the source and the relay to the destination, for which the PDF strategy is optimal. The second is a subclass in which the source does not transmit to the relay, for which a noise-forwarding strategy is optimal.

A beamforming system based on the acousto-optic effect

DEFF Research Database (Denmark)

Torras Rosell, Antoni; Barrera Figueroa, Salvador; Jacobsen, Finn

2012-01-01

Beamforming techniques are usually based on microphone arrays. The present work uses a beam of light as a sensor element, and describes a beamforming system that locates sound sources based on the acousto-optic effect, this is, the interaction between sound and light. The use of light as a sensin...

Robust Frequency Invariant Beamforming with Low Sidelobe for Speech Enhancement

Science.gov (United States)

Zhu, Yiting; Pan, Xiang

2018-01-01

Frequency invariant beamformers (FIBs) are widely used in speech enhancement and source localization. There are two traditional optimization methods for FIB design. The first one is convex optimization, which is simple but the frequency invariant characteristic of the beam pattern is poor with respect to frequency band of five octaves. The least squares (LS) approach using spatial response variation (SRV) constraint is another optimization method. Although, it can provide good frequency invariant property, it usually couldn’t be used in speech enhancement for its lack of weight norm constraint which is related to the robustness of a beamformer. In this paper, a robust wideband beamforming method with a constant beamwidth is proposed. The frequency invariant beam pattern is achieved by resolving an optimization problem of the SRV constraint to cover speech frequency band. With the control of sidelobe level, it is available for the frequency invariant beamformer (FIB) to prevent distortion of interference from the undesirable direction. The approach is completed in time-domain by placing tapped delay lines(TDL) and finite impulse response (FIR) filter at the output of each sensor which is more convenient than the Frost processor. By invoking the weight norm constraint, the robustness of the beamformer is further improved against random errors. Experiment results show that the proposed method has a constant beamwidth and almost the same white noise gain as traditional delay-and-sum (DAS) beamformer.

Alternate transmission with half-duplex relaying in MIMO interference relay networks

KAUST Repository

Park, Seongho

2013-12-01

In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups alternately every time phase. Each of the relaying groups has arbitrary number of relays, and each relay operates in half-duplex amplify-and-forward mode. In our scheme, the received signals at the relay nodes consist of desired signals and two different interference signals such as the inter-source interferences and the inter-group interferences which are caused by the phase incoherence of relaying. As such, we propose an iterative interference alignment algorithm to mitigate the interferences. We show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying system in the interference relay channels. © 2013 IEEE.

Energy efficient design for MIMO two-way AF multiple relay networks

KAUST Repository

Alsharoa, Ahmad M.; Ghazzai, Hakim; Alouini, Mohamed-Slim

2014-01-01

This paper studies the energy efficient transmission and the power allocation problem for multiple two-way relay networks equipped with multi-input multi-output antennas where each relay employs an amplify-and-forward strategy. The goal

Impact of Beamforming on the Path Connectivity in Cognitive Radio Ad Hoc Networks

Directory of Open Access Journals (Sweden)

Le The Dung

2017-03-01

Full Text Available This paper investigates the impact of using directional antennas and beamforming schemes on the connectivity of cognitive radio ad hoc networks (CRAHNs. Specifically, considering that secondary users use two kinds of directional antennas, i.e., uniform linear array (ULA and uniform circular array (UCA antennas, and two different beamforming schemes, i.e., randomized beamforming and center-directed to communicate with each other, we study the connectivity of all combination pairs of directional antennas and beamforming schemes and compare their performances to those of omnidirectional antennas. The results obtained in this paper show that, compared with omnidirectional transmission, beamforming transmission only benefits the connectivity when the density of secondary user is moderate. Moreover, the combination of UCA and randomized beamforming scheme gives the highest path connectivity in all evaluating scenarios. Finally, the number of antenna elements and degree of path loss greatly affect path connectivity in CRAHNs.

Alternate MIMO relaying with three AF relays using interference alignment

KAUST Repository

Park, Kihong

2012-06-01

In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss of capacity pre-log factor 1/2 in half duplex mode, where source transmit message to two relays and the other relay alternately. The inter-relay interference caused by alternate transmission is aligned to make additional degrees of freedom (DOFs). It is shown that the proposed scheme enables us to exploit 3M/4 DOFs compared with the M/2 DOFs of conventional AF relaying. More specifically, suboptimal linear filter designs for a source and three relays are proposed to maximize the achievable sum-rate. We verify using some selected numerical results that the proposed filter designs give significant improvement of the sum-rate over a naive filter and conventional relaying schemes. © 2012 IEEE.

Relay exchanges in elite short track speed skating.

Science.gov (United States)

Hext, Andrew; Heller, Ben; Kelley, John; Goodwill, Simon

2017-06-01

In short track speed skating, the relay exchange provides an additional strategic component to races by allowing a team to change the skater involved in the pack race. Typically executed every 1½ laps, it is the belief of skaters and coaches that during this period of the race, time can be gained or lost due to the execution of the relay exchange. As such, the aim of this study was to examine the influence of the relay exchange on a team's progression through a 5000 m relay race. Using data collected from three World Cup relay events during the 2012-2013 season, the time taken to complete the straight for the scenarios with and without the relay exchange were compared at different skating speeds for the corner exit prior to the straight. Overall, the influence of the relay exchange was found to be dependent on this corner exit speed. At slower corner exit speeds (12.01-13.5 m/s), relay exchange straight times were significantly faster than the free skating scenario (P < 0.01). While at faster corner exit speeds (14.01-15 m/s), straight times were significantly slower (P < 0.001). The findings of this study suggest that the current norm of executing relay exchanges every 1½ laps may not be optimal. Instead, varying the frequency of relay exchange execution throughout the race could allow: (1) time to be gained relative to other teams; and (2) facilitate other race strategies by providing an improved opportunity to overtake.

Relay race

CERN Multimedia

Staff Association

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

Relay race

CERN Document Server

Staff Association

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19th May starting at 12·15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the course, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay Some advice for all runners from the medical service can also be found here: https://espace.cern.ch/Running-Club/CERN-Relay/RelayPagePictures/MedicalServiceAnnoncement.pdf

Laser beam-forming by deformable mirror for laser isotope separation

International Nuclear Information System (INIS)

Nemoto, Koshichi; Fujii, Takashi; Goto, Naohiko

1995-01-01

A rectangular laser beam of uniform intensity is very suitable for laser isotope separation. In this paper, we propose a beam-forming system which consists two deformable mirrors. One of the mirrors changes the beam intensity and the other compensates for phase distortion. We developed a deformable mirror for beam-forming. Its deformed surface is similar to the ideal mirror surface for beam-forming. We reshaped a Gaussian-like He-Ne laser beam into a beam with a more uniform intensity profile by a simple deformable mirror. (author)

Nonfeedback Distributed Beamforming Using Spatial-Temporal Extraction

Directory of Open Access Journals (Sweden)

Pongnarin Sriploy

2016-01-01

Full Text Available So far, major phase synchronization techniques for distributed beamforming suffer from the problem related to the feedback procedure as a base station has to send the feedback reference signal back to the transmitting nodes. This requires stability of communication channel or a number of retransmissions, introducing a complicated system to both transmitter and receiver. Therefore, this paper proposes an alternative technique, so-called nonfeedback beamforming, employing an operation in both space and time domains. The proposed technique is to extract a combined signal at the base station. The concept of extraction is based on solving a simultaneous linear equation without the requirement of feedback or reference signals from base station. Also, the number of retransmissions is less compared with the ones available in literatures. As a result, the transmitting nodes are of low complexity and also low power consumption. The simulation and experimental results reveal that the proposed technique provides the optimum beamforming gain. Furthermore, it can reduce Bit Error Rate to the systems.

Maximizing Expected Achievable Rates for Block-Fading Buffer-Aided Relay Channels

KAUST Repository

Shaqfeh, Mohammad

2016-05-25

In this paper, the long-term average achievable rate over block-fading buffer-aided relay channels is maximized using a hybrid scheme that combines three essential transmission strategies, which are decode-and-forward, compress-and-forward, and direct transmission. The proposed hybrid scheme is dynamically adapted based on the channel state information. The integration and optimization of these three strategies provide a more generic and fundamental solution and give better achievable rates than the known schemes in the literature. Despite the large number of optimization variables, the proposed hybrid scheme can be optimized using simple closed-form formulas that are easy to apply in practical relay systems. This includes adjusting the transmission rate and compression when compress-and-forward is the selected strategy based on the channel conditions. Furthermore, in this paper, the hybrid scheme is applied to three different models of the Gaussian block-fading buffer-aided relay channels, depending on whether the relay is half or full duplex and whether the source and the relay have orthogonal or non-orthogonal channel access. Several numerical examples are provided to demonstrate the achievable rate results and compare them to the upper bounds of the ergodic capacity for each one of the three channel models under consideration.

Maximizing Expected Achievable Rates for Block-Fading Buffer-Aided Relay Channels

KAUST Repository

Shaqfeh, Mohammad; Zafar, Ammar; Alnuweiri, Hussein; Alouini, Mohamed-Slim

2016-01-01

In this paper, the long-term average achievable rate over block-fading buffer-aided relay channels is maximized using a hybrid scheme that combines three essential transmission strategies, which are decode-and-forward, compress-and-forward, and direct transmission. The proposed hybrid scheme is dynamically adapted based on the channel state information. The integration and optimization of these three strategies provide a more generic and fundamental solution and give better achievable rates than the known schemes in the literature. Despite the large number of optimization variables, the proposed hybrid scheme can be optimized using simple closed-form formulas that are easy to apply in practical relay systems. This includes adjusting the transmission rate and compression when compress-and-forward is the selected strategy based on the channel conditions. Furthermore, in this paper, the hybrid scheme is applied to three different models of the Gaussian block-fading buffer-aided relay channels, depending on whether the relay is half or full duplex and whether the source and the relay have orthogonal or non-orthogonal channel access. Several numerical examples are provided to demonstrate the achievable rate results and compare them to the upper bounds of the ergodic capacity for each one of the three channel models under consideration.

Relaxed Binaural LCMV Beamforming

NARCIS (Netherlands)

Koutrouvelis, A.; Hendriks, R.C.; Heusdens, R.; Jensen, Jesper Rindom

2017-01-01

In this paper, we propose a new binaural beamforming technique, which can be seen as a relaxation of the linearly constrained minimum variance (LCMV) framework. The proposed method can achieve simultaneous noise reduction and exact binaural cue preservation of the target source, similar to the

Use of Behavior and Influence Functions for Relay Selection in Cooperative Communications

DEFF Research Database (Denmark)

Craciunescu, Razvan; Mihovska, Albena Dimitrova; Prasad, Ramjee

2015-01-01

This paper uses a novel set of functions to model the relay selection process in a scenario of cooperative wireless communications. We define a utility function that reflects the behavior and influence that a selected relay may have on the quality of the link to be established for the forwarding...... of data. The utility function takes into account also the strategies of other players. To this end, we define a relay selection game and a supporting Nash Equilibrium (NE) algorithm for the choice of a relay during communication. The successful selection of a relay is evaluated by simulations in terms...

Beam-Forming Concentrating Solar Thermal Array Power Systems

Science.gov (United States)

Cwik, Thomas A. (Inventor); Dimotakis, Paul E. (Inventor); Hoppe, Daniel J. (Inventor)

2016-01-01

The present invention relates to concentrating solar-power systems and, more particularly, beam-forming concentrating solar thermal array power systems. A solar thermal array power system is provided, including a plurality of solar concentrators arranged in pods. Each solar concentrator includes a solar collector, one or more beam-forming elements, and one or more beam-steering elements. The solar collector is dimensioned to collect and divert incoming rays of sunlight. The beam-forming elements intercept the diverted rays of sunlight, and are shaped to concentrate the rays of sunlight into a beam. The steering elements are shaped, dimensioned, positioned, and/or oriented to deflect the beam toward a beam output path. The beams from the concentrators are converted to heat at a receiver, and the heat may be temporarily stored or directly used to generate electricity.

A User Cooperation Stimulating Strategy Based on Cooperative Game Theory in Cooperative Relay Networks

Directory of Open Access Journals (Sweden)

Ping Zhang

2009-01-01

Full Text Available This paper proposes a user cooperation stimulating strategy among rational users. The strategy is based on cooperative game theory and enacted in the context of cooperative relay networks. Using the pricing-based mechanism, the system is modeled initially with two nodes and a Base Station (BS. Within this framework, each node is treated as a rational decision maker. To this end, each node can decide whether to cooperate and how to cooperate. Cooperative game theory assists in providing an optimal system utility and provides fairness among users. Under different cooperative forwarding modes, certain questions are carefully investigated, including “what is each node's best reaction to maximize its utility?” and “what is the optimal reimbursement to encourage cooperation?” Simulation results show that the nodes benefit from the proposed cooperation stimulating strategy in terms of utility and thus justify the fairness between each user.

A User Cooperation Stimulating Strategy Based on Cooperative Game Theory in Cooperative Relay Networks

Directory of Open Access Journals (Sweden)

Jiang Fan

2009-01-01

Full Text Available This paper proposes a user cooperation stimulating strategy among rational users. The strategy is based on cooperative game theory and enacted in the context of cooperative relay networks. Using the pricing-based mechanism, the system is modeled initially with two nodes and a Base Station (BS. Within this framework, each node is treated as a rational decision maker. To this end, each node can decide whether to cooperate and how to cooperate. Cooperative game theory assists in providing an optimal system utility and provides fairness among users. Under different cooperative forwarding modes, certain questions are carefully investigated, including "what is each node's best reaction to maximize its utility?" and "what is the optimal reimbursement to encourage cooperation?" Simulation results show that the nodes benefit from the proposed cooperation stimulating strategy in terms of utility and thus justify the fairness between each user.

Reactive relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz

2012-06-01

Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference constraints to the primary users. Generally, relay selection is done on the basis of maximum end-to-end signal to noise ratio (SNR). However, it requires large amounts of channel state information (CSI) at different network nodes. In this paper, we present and analyze a reactive relay selection scheme in underlay cognitive networks where the relays are operating with fixed gains near a primary user. The system model minimizes the amount of CSI required at different nodes and the destination selects the best relay on the basis of maximum relay to destination SNR. We derive close form expressions for the received SNR statistics, outage probability, bit error probability and average channel capacity of the system. Simulation results are also presented to confirm the validity of the derived expressions. © 2012 IEEE.

Partial relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Hasna, Mazen Omar; Qaraqe, Khalid A.

2012-01-01

In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

Partial relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz

2012-05-01

In a communication system with multiple cooperative relays, selecting the best relay utilizes the available spectrum more efficiently. However, selective relaying poses a different problem in underlay cognitive networks compared to the traditional cooperative networks due to interference thresholds to the primary users. In most cases, a best relay is the one which provides the maximum end-to-end signal to noise ratio (SNR). This approach needs plenty of instantaneous channel state information (CSI). The CSI burden could be reduced by partial relay selection. In this paper, a partial relay selection scheme is presented and analyzed for an underlay cognitive network with fixed gain relays operating in the vicinity of a primary user. The system model is adopted in a way that each node needs minimal CSI to perform its task. The best relay is chosen on the basis of maximum source to relay link SNR which then forwards the message to the destination. We derive closed form expressions for the received SNR distributions, system outage, probability of bit error and average channel capacity of the system. The derived results are confirmed through simulations. © 2012 IEEE.

Enhanced linear-array photoacoustic beamforming using modified coherence factor

Science.gov (United States)

Mozaffarzadeh, Moein; Yan, Yan; Mehrmohammadi, Mohammad; Makkiabadi, Bahador

2018-02-01

Photoacoustic imaging (PAI) is a promising medical imaging modality providing the spatial resolution of ultrasound imaging and the contrast of optical imaging. For linear-array PAI, a beamformer can be used as the reconstruction algorithm. Delay-and-sum (DAS) is the most prevalent beamforming algorithm in PAI. However, using DAS beamformer leads to low-resolution images as well as high sidelobes due to nondesired contribution of off-axis signals. Coherence factor (CF) is a weighting method in which each pixel of the reconstructed image is weighted, based on the spatial spectrum of the aperture, to mainly improve the contrast. We demonstrate that the numerator of the formula of CF contains a DAS algebra and propose the use of a delay-multiply-and-sum beamformer instead of the available DAS on the numerator. The proposed weighting technique, modified CF (MCF), has been evaluated numerically and experimentally compared to CF. It was shown that MCF leads to lower sidelobes and better detectable targets. The quantitative results of the experiment (using wire targets) show that MCF leads to for about 45% and 40% improvement, in comparison with CF, in the terms of signal-to-noise ratio and full-width-half-maximum, respectively.

Detect-and-forward in two-hop relay channels: a metrics-based analysis

KAUST Repository

Benjillali, Mustapha; Szczecinski, Leszek

2010-01-01

In this paper, we analyze the coded performance of a cooperative system with multiple parallel relays using "Detect-and-Forward" (DetF) strategy where each relay demodulates the overheard signal and forwards the detected binary words. The proposed

Beamforming applied to surface EEG improves ripple visibility.

Science.gov (United States)

van Klink, Nicole; Mol, Arjen; Ferrier, Cyrille; Hillebrand, Arjan; Huiskamp, Geertjan; Zijlmans, Maeike

2018-01-01

Surface EEG can show epileptiform ripples in people with focal epilepsy, but identification is impeded by the low signal-to-noise ratio of the electrode recordings. We used beamformer-based virtual electrodes to improve ripple identification. We analyzed ten minutes of interictal EEG of nine patients with refractory focal epilepsy. EEGs with more than 60 channels and 20 spikes were included. We computed ∼79 virtual electrodes using a scalar beamformer and marked ripples (80-250 Hz) co-occurring with spikes in physical and virtual electrodes. Ripple numbers in physical and virtual electrodes were compared, and sensitivity and specificity of ripples for the region of interest (ROI; based on clinical information) were determined. Five patients had ripples in the physical electrodes and eight in the virtual electrodes, with more ripples in virtual than in physical electrodes (101 vs. 57, p = .007). Ripples in virtual electrodes predicted the ROI better than physical electrodes (AUC 0.65 vs. 0.56, p = .03). Beamforming increased ripple visibility in surface EEG. Virtual ripples predicted the ROI better than physical ripples, although sensitivity was still poor. Beamforming can facilitate ripple identification in EEG. Ripple localization needs to be improved to enable its use for presurgical evaluation in people with epilepsy. Copyright © 2017 International Federation of Clinical Neurophysiology. Published by Elsevier B.V. All rights reserved.

Low bandwidth binaural beamforming

NARCIS (Netherlands)

Srinivasan, S.

2008-01-01

An efficient beamforming scheme for wireless binaural hearing aids is proposed that provides a trade-off between the transmission bit rate and the amount of noise reduction. It is proposed to transmit only the low-frequency part of the signal from one hearing aid to the other, which is used in a

Threshold-Based Relay Selection for Detect-and-Forward Relaying in Cooperative Wireless Networks

Directory of Open Access Journals (Sweden)

Fan Yijia

2010-01-01

Full Text Available This paper studies two-hop cooperative demodulate-and-forward relaying using multiple relays in wireless networks. A threshold based relay selection scheme is considered, in which the reliable relays are determined by comparing source-relay SNR to a threshold, and one of the reliable relays is selected by the destination based on relay-destination SNR. The exact bit error rate of this scheme is derived, and a simple threshold function is proposed. It is shown that the network achieves full diversity order ( under the proposed threshold, where is the number of relays in the network. Unlike some other full diversity achieving protocols in the literature, the requirement that the instantaneous/average SNRs of the source-relay links be known at the destination is eliminated using the appropriate SNR threshold.

A phantom study on temporal and subband Minimum Variance adaptive beamforming

DEFF Research Database (Denmark)

Diamantis, Konstantinos; Voxen, Iben Holfort; Greenaway, Alan H.

2014-01-01

This paper compares experimentally temporal and subband implementations of the Minimum Variance (MV) adaptive beamformer for medical ultrasound imaging. The performance of the two approaches is tested by comparing wire phantom measurements, obtained by the research ultrasound scanner SARUS. A 7 MHz...... BK8804 linear transducer was used to scan a wire phantom in which wires are separated by 10 mm. Performance is then evaluated by the lateral Full-Width-Half-Maximum (FWHM), the Peak Sidelobe Level (PSL), and the computational load. Beamformed single emission responses are also compared with those...... from conventional Delay-and-Sum (DAS) beamformer. FWHM measured at the depth of 46.6 mm, is 0.02 mm (0.09λ) for both adaptive methods while the corresponding values for Hanning and Boxcar weights are 0.64 and 0.44 mm respectively. Between the MV beamformers a -2 dB difference in PSL is noticed in favor...

Robust Adaptive LCMV Beamformer Based On An Iterative Suboptimal Solution

Directory of Open Access Journals (Sweden)

Xiansheng Guo

2015-06-01

Full Text Available The main drawback of closed-form solution of linearly constrained minimum variance (CF-LCMV beamformer is the dilemma of acquiring long observation time for stable covariance matrix estimates and short observation time to track dynamic behavior of targets, leading to poor performance including low signal-noise-ratio (SNR, low jammer-to-noise ratios (JNRs and small number of snapshots. Additionally, CF-LCMV suffers from heavy computational burden which mainly comes from two matrix inverse operations for computing the optimal weight vector. In this paper, we derive a low-complexity Robust Adaptive LCMV beamformer based on an Iterative Suboptimal solution (RAIS-LCMV using conjugate gradient (CG optimization method. The merit of our proposed method is threefold. Firstly, RAIS-LCMV beamformer can reduce the complexity of CF-LCMV remarkably. Secondly, RAIS-LCMV beamformer can adjust output adaptively based on measurement and its convergence speed is comparable. Finally, RAIS-LCMV algorithm has robust performance against low SNR, JNRs, and small number of snapshots. Simulation results demonstrate the superiority of our proposed algorithms.

An applicable 5.8 GHz wireless power transmission system with rough beamforming to Project Loon

Directory of Open Access Journals (Sweden)

Chang-Jun Ahn

2016-06-01

Full Text Available In recent, Google proposed the Project Loon being developed with the mission of providing internet access to rural and remote areas using high-altitude balloons. In this paper, we describe an applicable prototype of 5.8 GHz wireless power transmission system with rough beamforming method to Project Loon. From the measurement results, transmit beamforming phased array antenna can transmit power more efficiently compared to a horn antenna and array antenna without beamforming with increasing the transmission distance. For the transmission distance of 1000 mm, transmit beamforming phased array antenna can obtain higher received power about 1.46 times compared to array antenna without transmit beamforming.

Linear-Array Photoacoustic Imaging Using Minimum Variance-Based Delay Multiply and Sum Adaptive Beamforming Algorithm

OpenAIRE

Mozaffarzadeh, Moein; Mahloojifar, Ali; Orooji, Mahdi; Kratkiewicz, Karl; Adabi, Saba; Nasiriavanaki, Mohammadreza

2017-01-01

In Photoacoustic imaging (PA), Delay-and-Sum (DAS) beamformer is a common beamforming algorithm having a simple implementation. However, it results in a poor resolution and high sidelobes. To address these challenges, a new algorithm namely Delay-Multiply-and-Sum (DMAS) was introduced having lower sidelobes compared to DAS. To improve the resolution of DMAS, a novel beamformer is introduced using Minimum Variance (MV) adaptive beamforming combined with DMAS, so-called Minimum Variance-Based D...

Telecommunications Relay Services

Science.gov (United States)

... Home » Health Info » Hearing, Ear Infections, and Deafness Telecommunications Relay Services On this page: What are telecommunication ... additional information about telecommunication relay services? What are telecommunication relay services? Title IV of the Americans with ...

Reactive relay selection in underlay cognitive networks with fixed gain relays

KAUST Repository

Hussain, Syed Imtiaz; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Hasna, Mazen Omar

2012-01-01

Best relay selection is a bandwidth efficient technique for multiple relay environments without compromising the system performance. The problem of relay selection is more challenging in underlay cognitive networks due to strict interference

Enhanced linear-array photoacoustic beamforming using modified coherence factor.

Science.gov (United States)

Mozaffarzadeh, Moein; Yan, Yan; Mehrmohammadi, Mohammad; Makkiabadi, Bahador

2018-02-01

Photoacoustic imaging (PAI) is a promising medical imaging modality providing the spatial resolution of ultrasound imaging and the contrast of optical imaging. For linear-array PAI, a beamformer can be used as the reconstruction algorithm. Delay-and-sum (DAS) is the most prevalent beamforming algorithm in PAI. However, using DAS beamformer leads to low-resolution images as well as high sidelobes due to nondesired contribution of off-axis signals. Coherence factor (CF) is a weighting method in which each pixel of the reconstructed image is weighted, based on the spatial spectrum of the aperture, to mainly improve the contrast. We demonstrate that the numerator of the formula of CF contains a DAS algebra and propose the use of a delay-multiply-and-sum beamformer instead of the available DAS on the numerator. The proposed weighting technique, modified CF (MCF), has been evaluated numerically and experimentally compared to CF. It was shown that MCF leads to lower sidelobes and better detectable targets. The quantitative results of the experiment (using wire targets) show that MCF leads to for about 45% and 40% improvement, in comparison with CF, in the terms of signal-to-noise ratio and full-width-half-maximum, respectively. (2018) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE).

An Optimal Analysis in Wireless Powered Full-duplex Relaying Network

Directory of Open Access Journals (Sweden)

K.-T. Nguyen

2017-04-01

Full Text Available Wireless-powered cellular networks (WPCNs are currently being investigated to exploit the reliability and improve battery lifetime of mobile users. This paper investigates the energy harvesting structure of the full-duplex relaying networks. By using the time switching based relaying (TSR protocol and Amplify-and-Forward (AF model in delay-limited transmission scheme, we propose the closed-form expression of the outage probability and then calculate the optimal throughput. An important result can be taken obviously that the time fraction in TSR, the position of relay, the noise as well as the energy conversation impacting on the outage probability as well as the optimal throughput. By Monte Carlo simulation, the numerical results indicate an effective relaying strategy in full-duplex cooperative systems. Finally, we provide fundamental design guidelines for selecting time fraction in TSR that satisfies the requirements of a practical relaying system.

Efficient incremental relaying

KAUST Repository

Fareed, Muhammad Mehboob

2013-07-01

We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying scheme with both amplify and forward and decode and forward relaying. Numerical results are also presented to verify their analytical counterparts. © 2013 IEEE.

Simulation Study of Real Time 3-D Synthetic Aperture Sequential Beamforming for Ultrasound Imaging

DEFF Research Database (Denmark)

Hemmsen, Martin Christian; Rasmussen, Morten Fischer; Stuart, Matthias Bo

2014-01-01

in the main system. The real-time imaging capability is achieved using a synthetic aperture beamforming technique, utilizing the transmit events to generate a set of virtual elements that in combination can generate an image. The two core capabilities in combination is named Synthetic Aperture Sequential......This paper presents a new beamforming method for real-time three-dimensional (3-D) ultrasound imaging using a 2-D matrix transducer. To obtain images with sufficient resolution and contrast, several thousand elements are needed. The proposed method reduces the required channel count from...... Beamforming (SASB). Simulations are performed to evaluate the image quality of the presented method in comparison to Parallel beamforming utilizing 16 receive beamformers. As indicators for image quality the detail resolution and Cystic resolution are determined for a set of scatterers at a depth of 90mm...

Analysis of Simulated and Measured Indoor Channels for mm-Wave Beamforming Applications

DEFF Research Database (Denmark)

Karstensen, Anders; Fan, Wei; Zhang, Fengchun

2018-01-01

was investigated using both single beam and multiple beams, with two different power allocation schemes applied to multi-beamforming. Channel measurements were performed at 28-30 GHz using a vector network analyzer equipped with a Biconical antenna as the transmit antenna and a rotated horn antenna as the receive...... antenna. 3D ray tracing simulations were carried out in the same replicated propagation environments. Based on measurement and ray tracing simulation data, it is shown that RT-assisted beamforming performs well both for single and multi-beamforming in these two representative indoor propagation...

On the power amplifier nonlinearity in MIMO transmit beamforming systems

KAUST Repository

Qi, Jian

2012-03-01

In this paper, single-carrier multiple-input multiple-output (MIMO) transmit beamforming (TB) systems in the presence of high-power amplifier (HPA) nonlinearity are investigated. Specifically, due to the suboptimality of the conventional maximal ratio transmission/maximal ratio combining (MRT/MRC) under HPA nonlinearity, we propose the optimal TB scheme with the optimal beamforming weight vector and combining vector, for MIMO systems with nonlinear HPAs. Moreover, an alternative suboptimal but much simpler TB scheme, namely, quantized equal gain transmission (QEGT), is proposed. The latter profits from the property that the elements of the beamforming weight vector have the same constant modulus. The performance of the proposed optimal TB scheme and QEGT/MRC technique in the presence of the HPA nonlinearity is evaluated in terms of the average symbol error probability and mutual information with the Gaussian input, considering the transmission over uncorrelated quasi-static frequency-flat Rayleigh fading channels. Numerical results are provided and show the effects on the performance of several system parameters, namely, the HPA parameters, numbers of antennas, quadrature amplitude modulation modulation order, number of pilot symbols, and cardinality of the beamforming weight vector codebook for QEGT. © 2012 IEEE.

On the power amplifier nonlinearity in MIMO transmit beamforming systems

KAUST Repository

Qi, Jian; Aissa, Sonia

2012-01-01

In this paper, single-carrier multiple-input multiple-output (MIMO) transmit beamforming (TB) systems in the presence of high-power amplifier (HPA) nonlinearity are investigated. Specifically, due to the suboptimality of the conventional maximal ratio transmission/maximal ratio combining (MRT/MRC) under HPA nonlinearity, we propose the optimal TB scheme with the optimal beamforming weight vector and combining vector, for MIMO systems with nonlinear HPAs. Moreover, an alternative suboptimal but much simpler TB scheme, namely, quantized equal gain transmission (QEGT), is proposed. The latter profits from the property that the elements of the beamforming weight vector have the same constant modulus. The performance of the proposed optimal TB scheme and QEGT/MRC technique in the presence of the HPA nonlinearity is evaluated in terms of the average symbol error probability and mutual information with the Gaussian input, considering the transmission over uncorrelated quasi-static frequency-flat Rayleigh fading channels. Numerical results are provided and show the effects on the performance of several system parameters, namely, the HPA parameters, numbers of antennas, quadrature amplitude modulation modulation order, number of pilot symbols, and cardinality of the beamforming weight vector codebook for QEGT. © 2012 IEEE.

Minimum Variance Beamforming for High Frame-Rate Ultrasound Imaging

DEFF Research Database (Denmark)

Holfort, Iben Kraglund; Gran, Fredrik; Jensen, Jørgen Arendt

2007-01-01

, a 7 MHz, 128-element, phased array transducer with lambda/2-spacing was used. Data is obtained using a single element as the transmitting aperture and all 128 elements as the receiving aperture. A full SA sequence consisting of 128 emissions was simulated by gliding the active transmitting element...... weights for each frequency sub-band. As opposed to the conventional, Delay and Sum (DS) beamformer, this approach is dependent on the specific data. The performance of the proposed MV beamformer is tested on simulated synthetic aperture (SA) ultrasound data, obtained using Field II. For the simulations...... across the array. Data for 13 point targets and a circular cyst with a radius of 5 mm were simulated. The performance of the MV beamformer is compared to DS using boxcar weights and Hanning weights, and is quantified by the Full Width at Half Maximum (FWHM) and the peak-side-lobe level (PSL). Single...

Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

KAUST Repository

Alsharoa, Ahmad M.

2013-05-08

In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single and multiple relay selection that maximize the sum rate of the secondary network without degrading the quality of service of the primary network by respecting a tolerated interference threshold were formulated. Single relay selection and optimal power allocation for two-way relaying cognitive radio networks using decode-and-forward and amplify-and-forward protocols were studied. Dual decomposition and subgradient methods were used to find the optimal power allocation. The transmission process to exchange two different messages between two transceivers for two-way relaying technique takes place in two time slots. In the first slot, the transceivers transmit their signals simultaneously to the relay. Then, during the second slot the relay broadcasts its signal to the terminals. Moreover, improvement of both spectral and energy efficiency can be achieved compared with the one-way relaying technique. As an extension, a multiple relay selection for both one-way and two-way relaying under cognitive radio scenario using amplify-and-forward were discussed. A strong optimization tool based on genetic and iterative algorithms was employed to solve the 
formulated optimization problems for both single and multiple relay selection, where discrete relay power levels were considered. Simulation results show that the practical and low-complexity heuristic approaches achieve almost the same performance of the optimal relay selection schemes either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity.

Transmit Antenna Selection for Multi-User Underlay Cognitive Transmission with Zero-Forcing Beamforming

KAUST Repository

Hanif, Muhammad

2017-03-20

We present a transmit antenna subset selection scheme for an underlay cognitive system serving multiple secondary receivers. The secondary system employs zero-forcing beamforming to nullify the interference to multiple primary users and eliminate inter-user interference to the secondary users simultaneously. Simulation results show that the proposed scheme achieves near-optimal performance with low computational complexity. Lastly, an optimal power allocation strategy is also introduced to improve the secondary network throughput.

Mutual Information of Buffer-Aided Full-Duplex Relay Channels

KAUST Repository

Shafie, Ahmed El

2017-04-09

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Mutual Information of Buffer-Aided Full-Duplex Relay Channels

KAUST Repository

Shafie, Ahmed El; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

2017-01-01

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multiple-output (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Joint source and relay optimization for interference MIMO relay networks

Science.gov (United States)

Khandaker, Muhammad R. A.; Wong, Kai-Kit

2017-12-01

This paper considers multiple-input multiple-output (MIMO) relay communication in multi-cellular (interference) systems in which MIMO source-destination pairs communicate simultaneously. It is assumed that due to severe attenuation and/or shadowing effects, communication links can be established only with the aid of a relay node. The aim is to minimize the maximal mean-square-error (MSE) among all the receiving nodes under constrained source and relay transmit powers. Both one- and two-way amplify-and-forward (AF) relaying mechanisms are considered. Since the exactly optimal solution for this practically appealing problem is intractable, we first propose optimizing the source, relay, and receiver matrices in an alternating fashion. Then we contrive a simplified semidefinite programming (SDP) solution based on the error covariance matrix decomposition technique, avoiding the high complexity of the iterative process. Numerical results reveal the effectiveness of the proposed schemes.

Delay and Standard Deviation Beamforming to Enhance Specular Reflections in Ultrasound Imaging.

Science.gov (United States)

Bandaru, Raja Sekhar; Sornes, Anders Rasmus; Hermans, Jeroen; Samset, Eigil; D'hooge, Jan

2016-12-01

Although interventional devices, such as needles, guide wires, and catheters, are best visualized by X-ray, real-time volumetric echography could offer an attractive alternative as it avoids ionizing radiation; it provides good soft tissue contrast, and it is mobile and relatively cheap. Unfortunately, as echography is traditionally used to image soft tissue and blood flow, the appearance of interventional devices in conventional ultrasound images remains relatively poor, which is a major obstacle toward ultrasound-guided interventions. The objective of this paper was therefore to enhance the appearance of interventional devices in ultrasound images. Thereto, a modified ultrasound beamforming process using conventional-focused transmit beams is proposed that exploits the properties of received signals containing specular reflections (as arising from these devices). This new beamforming approach referred to as delay and standard deviation beamforming (DASD) was quantitatively tested using simulated as well as experimental data using a linear array transducer. Furthermore, the influence of different imaging settings (i.e., transmit focus, imaging depth, and scan angle) on the obtained image contrast was evaluated. The study showed that the image contrast of specular regions improved by 5-30 dB using DASD beamforming compared with traditional delay and sum (DAS) beamforming. The highest gain in contrast was observed when the interventional device was tilted away from being orthogonal to the transmit beam, which is a major limitation in standard DAS imaging. As such, the proposed beamforming methodology can offer an improved visualization of interventional devices in the ultrasound image with potential implications for ultrasound-guided interventions.

Non-invasive beamforming add-on module

KAUST Repository

Bader, Ahmed; Alouini, Mohamed-Slim

2017-01-01

An embodiment of a non-invasive beamforming add-on apparatus couples to an existing antenna port and rectifies the beam azimuth in the upstream and downstream directions. The apparatus comprises input circuitry that is configured to receive one

Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

KAUST Repository

Park, Seongho; Park, Kihong; Ko, Youngchai; Alouini, Mohamed-Slim

2012-01-01

In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

Alternate transmission relaying based on interference alignment in 3-relay half-duplex MIMO systems

KAUST Repository

Park, Seongho

2012-09-01

In a half-duplex relaying, the capacity pre-log factor 1/2 is a major drawback in spectral efficiency. This paper proposes a linear precoding/decoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can suppress the inter-relay interference resulting from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2012 IEEE.

Beamforming under Quantization Errors in Wireless Binaural Hearing Aids

Directory of Open Access Journals (Sweden)

Srinivasan Sriram

2008-01-01

Full Text Available Improving the intelligibility of speech in different environments is one of the main objectives of hearing aid signal processing algorithms. Hearing aids typically employ beamforming techniques using multiple microphones for this task. In this paper, we discuss a binaural beamforming scheme that uses signals from the hearing aids worn on both the left and right ears. Specifically, we analyze the effect of a low bit rate wireless communication link between the left and right hearing aids on the performance of the beamformer. The scheme is comprised of a generalized sidelobe canceller (GSC that has two inputs: observations from one ear, and quantized observations from the other ear, and whose output is an estimate of the desired signal. We analyze the performance of this scheme in the presence of a localized interferer as a function of the communication bit rate using the resultant mean-squared error as the signal distortion measure.

Beamforming under Quantization Errors in Wireless Binaural Hearing Aids

Directory of Open Access Journals (Sweden)

Kees Janse

2008-09-01

Full Text Available Improving the intelligibility of speech in different environments is one of the main objectives of hearing aid signal processing algorithms. Hearing aids typically employ beamforming techniques using multiple microphones for this task. In this paper, we discuss a binaural beamforming scheme that uses signals from the hearing aids worn on both the left and right ears. Specifically, we analyze the effect of a low bit rate wireless communication link between the left and right hearing aids on the performance of the beamformer. The scheme is comprised of a generalized sidelobe canceller (GSC that has two inputs: observations from one ear, and quantized observations from the other ear, and whose output is an estimate of the desired signal. We analyze the performance of this scheme in the presence of a localized interferer as a function of the communication bit rate using the resultant mean-squared error as the signal distortion measure.

Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

KAUST Repository

El Shafie, Ahmed

2017-10-18

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Achievable Rates of Buffer-Aided Full-Duplex Gaussian Relay Channels

KAUST Repository

El Shafie, Ahmed; Salem, Ahmed Sultan; Krikidis, Ioannis; Al-Dhahir, Naofal; Hamila, Ridha

2017-01-01

We derive closed-form expressions for the achievable rates of a buffer-aided full-duplex (FD) multiple-input multipleoutput (MIMO) Gaussian relay channel. The FD relay still suffers from residual self-interference (RSI) after the application of self-interference mitigation techniques. We investigate both cases of a slow-RSI channel where the RSI is fixed over the entire codeword, and a fast-RSI channel where the RSI changes from one symbol duration to another within the codeword. We show that the RSI can be completely eliminated in the slow-RSI case when the FD relay is equipped with a buffer while the fast RSI cannot be eliminated. For the fixed-rate data transmission scenario, we derive the optimal transmission strategy that should be adopted by the source node and relay node to maximize the system throughput. We verify our analytical findings through simulations.

Radioisotope relay instrument

International Nuclear Information System (INIS)

Pozdnyakov, V.N.; Sazonov, O.L.; Taksar, I.M.; Tesnavs, Eh.R.; Yanushkovskij, V.A.

1974-01-01

The paper describes a radioisotope relay device containing a radiation source, a detector, an electronic relay block with a comparative threshold mechanism. The device differs from previously known ones in that, for the purpose of increasing stability and speed of action, the electronic relay block is a separate unit and contains two threshold pulse generators which are joined up, across series-connected ''and'' and ''or'' elements, with one of the inputs of the comparative threshold mechanism, whose second input is connected with a detector and whose outputs are connected with a relay element connected by feedback with the above-mentioned ''and'' elements. (author)

An Integrated Real-Time Beamforming and Postfiltering System for Nonstationary Noise Environments

Directory of Open Access Journals (Sweden)

Gannot Sharon

2003-01-01

Full Text Available We present a novel approach for real-time multichannel speech enhancement in environments of nonstationary noise and time-varying acoustical transfer functions (ATFs. The proposed system integrates adaptive beamforming, ATF identification, soft signal detection, and multichannel postfiltering. The noise canceller branch of the beamformer and the ATF identification are adaptively updated online, based on hypothesis test results. The noise canceller is updated only during stationary noise frames, and the ATF identification is carried out only when desired source components have been detected. The hypothesis testing is based on the nonstationarity of the signals and the transient power ratio between the beamformer primary output and its reference noise signals. Following the beamforming and the hypothesis testing, estimates for the signal presence probability and for the noise power spectral density are derived. Subsequently, an optimal spectral gain function that minimizes the mean square error of the log-spectral amplitude (LSA is applied. Experimental results demonstrate the usefulness of the proposed system in nonstationary noise environments.

Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

KAUST Repository

Park, Kihong

2014-05-01

In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary user (PU) is located close to the relay nodes, the performance of the secondary network is severely degraded due to the interference power constraint during the transmission in the second hop. We propose a decode and zero-forcing forward scheme to suppress the interference power at the relay nodes and analyze the statistics of the end-to-end signal-to-noise ratio when the relay nodes are located arbitrarily and experience therefore non-identical Rayleigh fading channels. Numerical results validate our theoretical results and show that our proposed scheme improves the performance of the CR network when the PU is close to the relay nodes. © 2014 IEEE.

PHASED ARRAY FEED CALIBRATION, BEAMFORMING, AND IMAGING

International Nuclear Information System (INIS)

Landon, Jonathan; Elmer, Michael; Waldron, Jacob; Jones, David; Stemmons, Alan; Jeffs, Brian D.; Warnick, Karl F.; Richard Fisher, J.; Norrod, Roger D.

2010-01-01

Phased array feeds (PAFs) for reflector antennas offer the potential for increased reflector field of view and faster survey speeds. To address some of the development challenges that remain for scientifically useful PAFs, including calibration and beamforming algorithms, sensitivity optimization, and demonstration of wide field of view imaging, we report experimental results from a 19 element room temperature L-band PAF mounted on the Green Bank 20 Meter Telescope. Formed beams achieved an aperture efficiency of 69% and a system noise temperature of 66 K. Radio camera images of several sky regions are presented. We investigate the noise performance and sensitivity of the system as a function of elevation angle with statistically optimal beamforming and demonstrate cancelation of radio frequency interference sources with adaptive spatial filtering.

On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

KAUST Repository

Park, Kihong

2012-03-01

In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity pre-log factor of 1/2 due to half-duplex relaying, we propose a new transmission protocol which combines alternate relaying and inter-relay interference alignment. We prove that the proposed scheme can (i) exploits M degrees of freedom (DOFs) and (ii) perfectly recover the pre-log factor loss if the number of relays is at least six. From our selected numerical results, we show that our proposed scheme gives significant improvement over conventional AF relaying which offers only M/2 DOFs. © 2012 IEEE.

Stochastic Beamforming via Compact Antenna Arrays

DEFF Research Database (Denmark)

Alrabadi, Osama; Pedersen, Gert Frølund

2012-01-01

The paper investigates the average beamforming (BF) gain of compact antenna arrays when statistical channel knowledge is available. The optimal excitation (precoding vector) and impedance termination that maximize the average BF gain are a compromise between the ones that maximize the array...

On achievable rates of interference and cognitive channels with a relay

KAUST Repository

Zorgui, Marwen; Rezki, Zouheir; Alouini, Mohamed-Slim

2015-01-01

We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

On achievable rates of interference and cognitive channels with a relay

KAUST Repository

Zorgui, Marwen

2015-08-30

We consider a two-user interference channel assisted by a relay. Treating interference as noise at the receivers, and adopting an amplify and forward (AF) strategy at the relay, we derive achievable rates of both users, for given powers. Next, we solve the optimal power allocation problem maximizing the weighted sum rate of both users with and without relay power optimization. In particular, we propose a simple iterative line search algorithm solving the joint optimization problem over the three transmit powers and show that optimizing the relay power enhances the performance of the system. Then, considering the first user as a primary user, we determine the maximum instantaneous rate that the secondary user can achieve subject to an outage constraint with respect to the primary user and a peak power constraint. We show that, likewise the first part, jointly optimizing the secondary user and the relay transmit powers enhances the secondary user performance.

Advanced Strategic and Tactical Relay Request Management for the Mars Relay Operations Service

Science.gov (United States)

Allard, Daniel A.; Wallick, Michael N.; Gladden, Roy E.; Wang, Paul; Hy, Franklin H.

2013-01-01

This software provides a new set of capabilities for the Mars Relay Operations Service (MaROS) in support of Strategic and Tactical relay, including a highly interactive relay request Web user interface, mission control over relay planning time periods, and mission management of allowed strategic vs. tactical request parameters. Together, these new capabilities expand the scope of the system to include all elements critical for Tactical relay operations. Planning of replay activities spans a time period that is split into two distinct phases. The first phase is called Strategic, which begins at the time that relay opportunities are identified, and concludes at the point that the orbiter generates the flight sequences for on board execution. Any relay request changes from this point on are called Tactical. Tactical requests, otherwise called Orbit - er Relay State Changes (ORSC), are highly restricted in terms of what types of changes can be made, and the types of parameters that can be changed may differ from one orbiter to the next. For example, one orbiter may be able to delay the start of a relay request, while another may not. The legacy approach to ORSC management involves exchanges of e-mail with "requests for change" and "acknowledgement of approval," with no other tracking of changes outside of e-mail folders. MaROS Phases 1 and 2 provided the infrastructure for strategic relay for all supported missions. This new version, 3.0, introduces several capabilities that fully expand the scope of the system to include tactical relay. One new feature allows orbiter users to manage and "lock" Planning Periods, which allows the orbiter team to formalize the changeover from Strategic to Tactical operations. Another major feature allows users to interactively submit tactical request changes via a Web user interface. A third new feature allows orbiter missions to specify allowed tactical updates, which are automatically incorporated into the tactical change process

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla

2011-11-01

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a MIMO-relay node. The channel state information (CSI) available at the relay node is assumed to be imperfect. We consider robust designs for two models of CSI error. The first model is a stochastic error (SE) model, where the probability distribution of the CSI error is Gaussian. This model is applicable when the imperfect CSI is mainly due to errors in channel estimation. For this model, we propose robust minimum sum mean square error (SMSE), MSE-balancing, and relay transmit power minimizing precoder designs. The next model for the CSI error is a norm-bounded error (NBE) model, where the CSI error can be specified by an uncertainty set. This model is applicable when the CSI error is dominated by quantization errors. In this case, we adopt a worst-case design approach. For this model, we propose a robust precoder design that minimizes total relay transmit power under constraints on MSEs at the destination nodes. We show that the proposed robust design problems can be reformulated as convex optimization problems that can be solved efficiently using interior-point methods. We demonstrate the robust performance of the proposed design through simulations. © 2011 IEEE.

Switched diversity strategies for dual-hop amplify-and-forward relaying systems

KAUST Repository

Gaaloul, Fakhreddine; Radaydeh, Redha Mahmoud Mesleh; Alouini, Mohamed-Slim

2012-01-01

This study investigates different receive single-branch switch-based diversity schemes for dual-hop amplify-and-forward relaying networks. Specifically, three receive processing algorithms are adopted, in which the receive branch is selected using

Microwave beamforming for non-invasive patient-specific hyperthermia treatment of pediatric brain cancer

International Nuclear Information System (INIS)

Burfeindt, Matthew J; Zastrow, Earl; Hagness, Susan C; Van Veen, Barry D; Medow, Joshua E

2011-01-01

We present a numerical study of an array-based microwave beamforming approach for non-invasive hyperthermia treatment of pediatric brain tumors. The transmit beamformer is designed to achieve localized heating-that is, to achieve constructive interference and selective absorption of the transmitted electromagnetic waves at the desired focus location in the brain while achieving destructive interference elsewhere. The design process takes into account patient-specific and target-specific propagation characteristics at 1 GHz. We evaluate the effectiveness of the beamforming approach using finite-difference time-domain simulations of two MRI-derived child head models from the Virtual Family (IT'IS Foundation). Microwave power deposition and the resulting steady-state thermal distribution are calculated for each of several randomly chosen focus locations. We also explore the robustness of the design to mismatch between the assumed and actual dielectric properties of the patient. Lastly, we demonstrate the ability of the beamformer to suppress hot spots caused by pockets of cerebrospinal fluid (CSF) in the brain. Our results show that microwave beamforming has the potential to create localized heating zones in the head models for focus locations that are not surrounded by large amounts of CSF. These promising results suggest that the technique warrants further investigation and development.

Decode and Zero-Forcing Forward Relaying with Relay Selection in Cognitive Radio Systems

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim

2014-01-01

In this paper, we investigate a cognitive radio (CR) relay network with multiple relay nodes that help forwarding the signal of CR users. Best relay selection is considered to take advantage of its low complexity of implementation. When the primary

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

KAUST Repository

Pandarakkottilil, Ubaidulla; Chockalingam, A.

2011-01-01

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a

Linear-array photoacoustic imaging using minimum variance-based delay multiply and sum adaptive beamforming algorithm

Science.gov (United States)

Mozaffarzadeh, Moein; Mahloojifar, Ali; Orooji, Mahdi; Kratkiewicz, Karl; Adabi, Saba; Nasiriavanaki, Mohammadreza

2018-02-01

In photoacoustic imaging, delay-and-sum (DAS) beamformer is a common beamforming algorithm having a simple implementation. However, it results in a poor resolution and high sidelobes. To address these challenges, a new algorithm namely delay-multiply-and-sum (DMAS) was introduced having lower sidelobes compared to DAS. To improve the resolution of DMAS, a beamformer is introduced using minimum variance (MV) adaptive beamforming combined with DMAS, so-called minimum variance-based DMAS (MVB-DMAS). It is shown that expanding the DMAS equation results in multiple terms representing a DAS algebra. It is proposed to use the MV adaptive beamformer instead of the existing DAS. MVB-DMAS is evaluated numerically and experimentally. In particular, at the depth of 45 mm MVB-DMAS results in about 31, 18, and 8 dB sidelobes reduction compared to DAS, MV, and DMAS, respectively. The quantitative results of the simulations show that MVB-DMAS leads to improvement in full-width-half-maximum about 96%, 94%, and 45% and signal-to-noise ratio about 89%, 15%, and 35% compared to DAS, DMAS, MV, respectively. In particular, at the depth of 33 mm of the experimental images, MVB-DMAS results in about 20 dB sidelobes reduction in comparison with other beamformers.

Joint User Scheduling and MU-MIMO Hybrid Beamforming Algorithm for mmWave FDMA Massive MIMO System

Directory of Open Access Journals (Sweden)

Jing Jiang

2016-01-01

Full Text Available The large bandwidth and multipath in millimeter wave (mmWave cellular system assure the existence of frequency selective channels; it is necessary that mmWave system remains with frequency division multiple access (FDMA and user scheduling. But for the hybrid beamforming system, the analog beamforming is implemented by the same phase shifts in the entire frequency band, and the wideband phase shifts may not be harmonious with all users scheduled in frequency resources. This paper proposes a joint user scheduling and multiuser hybrid beamforming algorithm for downlink massive multiple input multiple output (MIMO orthogonal frequency division multiple access (OFDMA systems. In the first step of user scheduling, the users with identical optimal beams form an OFDMA user group and multiplex the entire frequency resource. Then base station (BS allocates the frequency resources for each member of OFDMA user group. An OFDMA user group can be regarded as a virtual user; thus it can support arbitrary MU-MIMO user selection and beamforming algorithms. Further, the analog beamforming vectors employ the best beam of each selected MU-MIMO user and the digital beamforming algorithm is solved by weight MMSE to acquire the best performance gain and mitigate the interuser inference. Simulation results show that hybrid beamforming together with user scheduling can greatly improve the performance of mmWave OFDMA massive MU-MIMO system.

An object-oriented multi-threaded software beamformation toolbox

DEFF Research Database (Denmark)

Hansen, Jens Munk; Hemmsen, Martin Christian; Jensen, Jørgen Arendt

2011-01-01

Focusing and apodization are an essential part of signal processing in ultrasound imaging. Although the fun- damental principles are simple, the dramatic increase in computational power of CPUs, GPUs, and FPGAs motivates the development of software based beamformers, which further improves image...... new beam formation strategies. It is a general 3D implementation capable of handling a multitude of focusing methods, interpolation schemes, and parametric and dynamic apodization. Despite being exible, it is capable of exploiting parallelization on a single computer, on a cluster, or on both....... On a single computer, it mimics the parallization in a scanner containing multiple beam formers. The focusing is determined using the positions of the transducer elements, presence of virtual sources, and the focus points. For interpolation, a number of interpolation schemes can be chosen, e.g. linear, polyno...

A scalable-low cost architecture for high gain beamforming antennas

KAUST Repository

Bakr, Omar; Johnson, Mark; Jungdong Park,; Adabi, Ehsan; Jones, Kevin; Niknejad, Ali

2010-01-01

Many state-of-the-art wireless systems, such as long distance mesh networks and high bandwidth networks using mm-wave frequencies, require high gain antennas to overcome adverse channel conditions. These networks could be greatly aided by adaptive beamforming antenna arrays, which can significantly simplify the installation and maintenance costs (e.g., by enabling automatic beam alignment). However, building large, low cost beamforming arrays is very complicated. In this paper, we examine the main challenges presented by large arrays, starting from electromagnetic and antenna design and proceeding to the signal processing and algorithms domain. We propose 3-dimensional antenna structures and hybrid RF/digital radio architectures that can significantly reduce the complexity and improve the power efficiency of adaptive array systems. We also present signal processing techniques based on adaptive filtering methods that enhance the robustness of these architectures. Finally, we present computationally efficient vector quantization techniques that significantly improve the interference cancellation capabilities of analog beamforming architectures. © 2010 IEEE.

A scalable-low cost architecture for high gain beamforming antennas

KAUST Repository

Bakr, Omar

2010-10-01

Many state-of-the-art wireless systems, such as long distance mesh networks and high bandwidth networks using mm-wave frequencies, require high gain antennas to overcome adverse channel conditions. These networks could be greatly aided by adaptive beamforming antenna arrays, which can significantly simplify the installation and maintenance costs (e.g., by enabling automatic beam alignment). However, building large, low cost beamforming arrays is very complicated. In this paper, we examine the main challenges presented by large arrays, starting from electromagnetic and antenna design and proceeding to the signal processing and algorithms domain. We propose 3-dimensional antenna structures and hybrid RF/digital radio architectures that can significantly reduce the complexity and improve the power efficiency of adaptive array systems. We also present signal processing techniques based on adaptive filtering methods that enhance the robustness of these architectures. Finally, we present computationally efficient vector quantization techniques that significantly improve the interference cancellation capabilities of analog beamforming architectures. © 2010 IEEE.

CERN Relay Race

CERN Document Server

CERN Running Club

2010-01-01

The CERN relay race will take place around the Meyrin site on Thursday 20 May, starting at 12.15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on the route, and how to register your team for the relay race, can be found at: https://espace.cern.ch/Running-Club/CERN-Relay

Alternate MIMO relaying with three AF relays using interference alignment

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim

2012-01-01

In this paper, we study a two-hop half-duplex relaying network with one source, one destination, and three amplify-and-forward (AF) relays equipped with M antennas each. We consider alternate transmission to compensate for the inherent loss

Efficient power allocation for fixed-gain amplify-and-forward relaying in rayleigh fading

KAUST Repository

Zafar, Ammar

2013-06-01

In this paper, we study power allocation strategies for a fixed-gain amplify-and-forward relay network employing multiple relays. We consider two optimization problems for the relay network: 1) optimal power allocation to maximize the end-to-end signal-to-noise ratio (SNR) and 2) minimizing the total consumed power while maintaining the end-to-end SNR over a threshold value. We assume that the relays have knowledge of only the channel statistics of all the links. We show that the SNR maximization problem is concave and the power minimization problem is convex. Hence, we solve the problems through convex programming. Numerical results show the benefit of allocating power optimally rather than uniformly. © 2013 IEEE.

Consumption Factor Optimization for Multihop Relaying over Nakagami-m Fading channels

KAUST Repository

Randrianantenaina, Itsikiantsoa

2015-10-06

In this paper, the energy efficiency of multihop relaying over Nakagami-m fading channels is investigated. The “consumption factor”, adopted as a metric to evaluate the energy efficiency, is derived for both amplify-and-forward and decodeand- forward relaying strategies. Then, based on the obtained expressions, we propose a power allocation strategy maximizing the consumption factor. In addition, a sub-optimal, low complexity, power allocation algorithm is proposed and analyzed, and the obtained power allocation scheme is compared in terms of energy efficiency to other power allocation schemes from the literature. Analytical and simulation results confirm the accuracy of our derivations, and assess the performance gains of the proposed approach.

Consumption Factor Optimization for Multihop Relaying over Nakagami-m Fading channels

KAUST Repository

Randrianantenaina, Itsikiantsoa; Benjillali, Mustapha; Alouini, Mohamed-Slim

2015-01-01

In this paper, the energy efficiency of multihop relaying over Nakagami-m fading channels is investigated. The “consumption factor”, adopted as a metric to evaluate the energy efficiency, is derived for both amplify-and-forward and decodeand- forward relaying strategies. Then, based on the obtained expressions, we propose a power allocation strategy maximizing the consumption factor. In addition, a sub-optimal, low complexity, power allocation algorithm is proposed and analyzed, and the obtained power allocation scheme is compared in terms of energy efficiency to other power allocation schemes from the literature. Analytical and simulation results confirm the accuracy of our derivations, and assess the performance gains of the proposed approach.

Implementing Strategic Planning Capabilities Within the Mars Relay Operations Service

Science.gov (United States)

Hy, Franklin; Gladden, Roy; Allard, Dan; Wallick, Michael

2011-01-01

Since the Mars Exploration Rovers (MER), Spirit and Opportunity, began their travels across the Martian surface in January of 2004, orbiting spacecraft such as the Mars 2001 Odyssey orbiter have relayed the majority of their collected scientific and operational data to and from Earth. From the beginning of those missions, it was evident that using orbiters to relay data to and from the surface of Mars was a vastly more efficient communications strategy in terms of power consumption and bandwidth compared to direct-to-Earth means. However, the coordination between the various spacecraft, which are largely managed independently and on differing commanding timelines, has always proven to be a challenge. Until recently, the ground operators of all these spacecraft have coordinated the movement of data through this network using a collection of ad hoc human interfaces and various, independent software tools. The Mars Relay Operations Service (MaROS) has been developed to manage the evolving needs of the Mars relay network, and specifically to standardize and integrate the relay planning and coordination data into a centralized infrastructure. This paper explores the journey of developing the MaROS system, from inception to delivery and acceptance by the Mars mission users.

Robust Nearfield Wideband Beamforming Design Based on Adaptive-Weighted Convex Optimization

Directory of Open Access Journals (Sweden)

Guo Ye-Cai

2017-01-01

Full Text Available Nearfield wideband beamformers for microphone arrays have wide applications in multichannel speech enhancement. The nearfield wideband beamformer design based on convex optimization is one of the typical representatives of robust approaches. However, in this approach, the coefficient of convex optimization is a constant, which has not used all the freedom provided by the weighting coefficient efficiently. Therefore, it is still necessary to further improve the performance. To solve this problem, we developed a robust nearfield wideband beamformer design approach based on adaptive-weighted convex optimization. The proposed approach defines an adaptive-weighted function by the adaptive array signal processing theory and adjusts its value flexibly, which has improved the beamforming performance. During each process of the adaptive updating of the weighting function, the convex optimization problem can be formulated as a SOCP (Second-Order Cone Program problem, which could be solved efficiently using the well-established interior-point methods. This method is suitable for the case where the sound source is in the nearfield range, can work well in the presence of microphone mismatches, and is applicable to arbitrary array geometries. Several design examples are presented to verify the effectiveness of the proposed approach and the correctness of the theoretical analysis.

80537 based distance relay

DEFF Research Database (Denmark)

Pedersen, Knud Ole Helgesen

1999-01-01

A method for implementing a digital distance relay in the power system is described.Instructions are given on how to program this relay on a 80537 based microcomputer system.The problem is used as a practical case study in the course 53113: Micocomputer applications in the power system.The relay...

Detect-and-forward in two-hop relay channels: a metrics-based analysis

KAUST Repository

Benjillali, Mustapha

2010-06-01

In this paper, we analyze the coded performance of a cooperative system with multiple parallel relays using "Detect-and-Forward" (DetF) strategy where each relay demodulates the overheard signal and forwards the detected binary words. The proposed method is based on the probabilistic characterization of the reliability metrics given under the form of L-values. First, we derive analytical expressions of the probability density functions (PDFs) of the L-values in the elementary two-hop DetF relay channel with different source-relay channel state information assumptions. Then, we apply the obtained expressions to calculate the theoretically achievable rates and compare them with the practical throughput of a simulated turbo-coded transmission. Next, we derive tight approximations for the end-to-end coded bit error rate (BER) of a general cooperative scheme with multiple parallel relays. Simulation results demonstrate the accuracy of our derivations for different cooperation configurations and conditions. © 2010 IEEE.

Relay Selection and Resource Allocation in One-Way and Two-Way Cognitive Relay Networks

KAUST Repository

Alsharoa, Ahmad M.

2013-01-01

In this work, the problem of relay selection and resource power allocation in one- way and two-way cognitive relay networks using half duplex channels with different relaying protocols is investigated. Optimization problems for both single

A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

KAUST Repository

Alsharoa, Ahmad M.; Ghazzai, Hakim; Alouini, Mohamed-Slim

2013-01-01

In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward

An evaluation of the performance of two binaural beamformers in complex and dynamic multitalker environments.

Science.gov (United States)

Best, Virginia; Mejia, Jorge; Freeston, Katrina; van Hoesel, Richard J; Dillon, Harvey

2015-01-01

Binaural beamformers are super-directional hearing aids created by combining microphone outputs from each side of the head. While they offer substantial improvements in SNR over conventional directional hearing aids, the benefits (and possible limitations) of these devices in realistic, complex listening situations have not yet been fully explored. In this study we evaluated the performance of two experimental binaural beamformers. Testing was carried out using a horizontal loudspeaker array. Background noise was created using recorded conversations. Performance measures included speech intelligibility, localization in noise, acceptable noise level, subjective ratings, and a novel dynamic speech intelligibility measure. Participants were 27 listeners with bilateral hearing loss, fitted with BTE prototypes that could be switched between conventional directional or binaural beamformer microphone modes. Relative to the conventional directional microphones, both binaural beamformer modes were generally superior for tasks involving fixed frontal targets, but not always for situations involving dynamic target locations. Binaural beamformers show promise for enhancing listening in complex situations when the location of the source of interest is predictable.

Efficient incremental relaying

KAUST Repository

Fareed, Muhammad Mehboob; Alouini, Mohamed-Slim

2013-01-01

We propose a novel relaying scheme which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission

Linear-array photoacoustic imaging using minimum variance-based delay multiply and sum adaptive beamforming algorithm.

Science.gov (United States)

Mozaffarzadeh, Moein; Mahloojifar, Ali; Orooji, Mahdi; Kratkiewicz, Karl; Adabi, Saba; Nasiriavanaki, Mohammadreza

2018-02-01

In photoacoustic imaging, delay-and-sum (DAS) beamformer is a common beamforming algorithm having a simple implementation. However, it results in a poor resolution and high sidelobes. To address these challenges, a new algorithm namely delay-multiply-and-sum (DMAS) was introduced having lower sidelobes compared to DAS. To improve the resolution of DMAS, a beamformer is introduced using minimum variance (MV) adaptive beamforming combined with DMAS, so-called minimum variance-based DMAS (MVB-DMAS). It is shown that expanding the DMAS equation results in multiple terms representing a DAS algebra. It is proposed to use the MV adaptive beamformer instead of the existing DAS. MVB-DMAS is evaluated numerically and experimentally. In particular, at the depth of 45 mm MVB-DMAS results in about 31, 18, and 8 dB sidelobes reduction compared to DAS, MV, and DMAS, respectively. The quantitative results of the simulations show that MVB-DMAS leads to improvement in full-width-half-maximum about 96%, 94%, and 45% and signal-to-noise ratio about 89%, 15%, and 35% compared to DAS, DMAS, MV, respectively. In particular, at the depth of 33 mm of the experimental images, MVB-DMAS results in about 20 dB sidelobes reduction in comparison with other beamformers. (2018) COPYRIGHT Society of Photo-Optical Instrumentation Engineers (SPIE).

Outage performance of two-way DF relaying systems with a new relay selection metric

KAUST Repository

Hyadi, Amal; Benjillali, Mustapha; Alouini, Mohamed-Slim

2012-01-01

This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both

76 FR 24442 - Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and...

Science.gov (United States)

2011-05-02

... same meaning as the terms ``small business,'' ``small organization,'' and ``small governmental...] Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services and Speech-to... Commission's Structure and Practices of the Video Relay Service Program; Telecommunications Relay Services...

Energy efficient design for MIMO two-way AF multiple relay networks

KAUST Repository

Alsharoa, Ahmad M.

2014-04-01

This paper studies the energy efficient transmission and the power allocation problem for multiple two-way relay networks equipped with multi-input multi-output antennas where each relay employs an amplify-and-forward strategy. The goal is to minimize the total power consumption without degrading the quality of service of the terminals. In our analysis, we start by deriving closed-form expressions of the optimal powers allocated to terminals. We then employ a strong optimization tool based on the particle swarm optimization technique to find the optimal power allocated at each relay antenna. Our numerical results illustrate the performance of the proposed scheme and show that it achieves a sub-optimal solution very close to the optimal one.

Alternate transmission with half-duplex relaying in MIMO interference relay networks

KAUST Repository

Park, Seongho; Ko, Youngchai; Park, Kihong; Alouini, Mohamed-Slim

2013-01-01

In this paper, we consider an alternate transmission scheme for a multiple-input multiple-output interference relay channel where multiple sources transmit their own signals to their corresponding destinations via one of two relaying groups

Opportunistic Relay Selection With Limited Feedback

KAUST Repository

Eltayeb, Mohammed E.; Elkhalil, Khalil; Bahrami, Hamid Reza; Al-Naffouri, Tareq Y.

2015-01-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision

CERN Relay Race

CERN Document Server

2008-01-01

The CERN relay race will take place around the Meyrin site on Thursday 5 June starting at 12:15 p.m. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

CERN Relay Race

CERN Document Server

2007-01-01

The CERN relay race will take place around the Meyrin site on Wednesday 23 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site. You can access the online registration form at: http://cern.ch/club-running-relay/form.html

Power system relaying

CERN Document Server

Horowitz, Stanley H; Niemira, James K

2013-01-01

The previous three editions of Power System Relaying offer comprehensive and accessible coverage of the theory and fundamentals of relaying and have been widely adopted on university and industry courses worldwide. With the third edition, the authors have added new and detailed descriptions of power system phenomena such as stability, system-wide protection concepts and discussion of historic outages. Power System Relaying, 4th Edition continues its role as an outstanding textbook on power system protection for senior and graduate students in the field of electric power engineering and a refer

Performance of amplify-and-forward multihop transmission over relay clusters with different routing strategies

KAUST Repository

Yilmaz, Ferkan; Khan, Fahd Ahmed; Alouini, Mohamed-Slim

2014-01-01

We consider a multihop relay network in which two terminals are communicating with each other via a number of cluster of relays. Performance of such networks depends on the routing protocols employed. In this paper, we find the expressions for the Average Symbol Error Probability (ASEP) performance of Amplify-and-Forward (AF) multihop transmission for the simplest routing protocol in which the relay transmits using the channel having the best Signal to Noise Ratio (SNR). The ASEP performance of a better protocol proposed in Gui et al. (2009) known as the adhoc protocol is also analyzed. The derived expressions for the performance are a convenient tool to analyze the performance of AF multihop transmission over relay clusters. Monte-Carlo simulations verify the correctness of the proposed formulation and are in agreement with analytical results. Furthermore, we propose new generalized protocols termed as last-nhop selection protocol, the dual path protocol, the forward-backward last-n-hop selection protocol and the forward-backward dual path protocol, to get improved ASEP performances. The ASEP performance of these proposed schemes is analysed by computer simulations. It is shown that close to optimal performance can be achieved by using the last-n-hop selection protocol and its forwardbackward variant. The complexity of the protocols is also studied. Copyright © 2014 Inderscience Enterprises Ltd.

Development of an acoustic steam generator leak detection system using delay-and-sum beamformer

International Nuclear Information System (INIS)

Chikazawa, Yoshitaka

2009-01-01

A new acoustic steam generator leak detection system using delay-and-sum beamformer is proposed. The major advantage of the delay-and-sum beamformer is it could provide information of acoustic source direction. An acoustic source of a sodium-water reaction is supposed to be localized while the background noise of the steam generator operation is uniformly distributed in the steam generator tube region. Therefore the delay-and-sum beamformer could distinguish the acoustic source of the sodium-water reaction from steam generator background noise. In this paper, results from numerical analyses are provided to show fundamental feasibility of the new method. (author)

Strong reflector-based beamforming in ultrasound medical imaging.

Science.gov (United States)

Szasz, Teodora; Basarab, Adrian; Kouamé, Denis

2016-03-01

This paper investigates the use of sparse priors in creating original two-dimensional beamforming methods for ultrasound imaging. The proposed approaches detect the strong reflectors from the scanned medium based on the well known Bayesian Information Criteria used in statistical modeling. Moreover, they allow a parametric selection of the level of speckle in the final beamformed image. These methods are applied on simulated data and on recorded experimental data. Their performance is evaluated considering the standard image quality metrics: contrast ratio (CR), contrast-to-noise ratio (CNR) and signal-to-noise ratio (SNR). A comparison is made with the classical delay-and-sum and minimum variance beamforming methods to confirm the ability of the proposed methods to precisely detect the number and the position of the strong reflectors in a sparse medium and to accurately reduce the speckle and highly enhance the contrast in a non-sparse medium. We confirm that our methods improve the contrast of the final image for both simulated and experimental data. In all experiments, the proposed approaches tend to preserve the speckle, which can be of major interest in clinical examinations, as it can contain useful information. In sparse mediums we achieve a highly improvement in contrast compared with the classical methods. Copyright © 2015 Elsevier B.V. All rights reserved.

Joint sub-carrier pairing and resource allocation for cognitive networks with adaptive relaying

KAUST Repository

Soury, Hamza; Bader, F.; Shaat, M.; Alouini, Mohamed-Slim

2013-01-01

Relayed transmission in a cognitive radio (CR) environment could be used to increase the coverage and capacity of communication system that benefits already from the efficient management of the spectrum developed by CR. Furthermore, there are many types of cooperative communications, including decode-and-forward (DAF) and amplify-and-forward (AAF). In this paper, these techniques are combined in an adaptive mode to benefit from its forwarding advantages; this mode is called adaptive relaying protocol (ARP). Moreover, this work focuses on the joint power allocation in a cognitive radio system in a cooperative mode that operates ARP in multi-carrier mode. The multi-carrier scenario is used in an orthogonal frequency division multiplexing (OFDM) mode, and the problem is formulated to maximize the end-to-end rate by searching the best power allocation at the transmitters. This work includes, besides the ARP model, a sub-carrier pairing strategy that allows the relays to switch to the best sub-carrier pairs to increase the throughput. The optimization problem is formulated and solved under the interference and power budget constraints using the sub-gradient algorithm. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques. The results show also the consequence of the choice of the pairing strategy. 2013 Stolojescu-Crisan and Isar; licensee Springer.

Joint sub-carrier pairing and resource allocation for cognitive networks with adaptive relaying

KAUST Repository

Soury, Hamza

2013-11-09

Relayed transmission in a cognitive radio (CR) environment could be used to increase the coverage and capacity of communication system that benefits already from the efficient management of the spectrum developed by CR. Furthermore, there are many types of cooperative communications, including decode-and-forward (DAF) and amplify-and-forward (AAF). In this paper, these techniques are combined in an adaptive mode to benefit from its forwarding advantages; this mode is called adaptive relaying protocol (ARP). Moreover, this work focuses on the joint power allocation in a cognitive radio system in a cooperative mode that operates ARP in multi-carrier mode. The multi-carrier scenario is used in an orthogonal frequency division multiplexing (OFDM) mode, and the problem is formulated to maximize the end-to-end rate by searching the best power allocation at the transmitters. This work includes, besides the ARP model, a sub-carrier pairing strategy that allows the relays to switch to the best sub-carrier pairs to increase the throughput. The optimization problem is formulated and solved under the interference and power budget constraints using the sub-gradient algorithm. The simulation results confirm the efficiency of the proposed adaptive relaying protocol in comparison to other relaying techniques. The results show also the consequence of the choice of the pairing strategy. 2013 Stolojescu-Crisan and Isar; licensee Springer.

SVD-BASED TRANSMIT BEAMFORMING FOR VARIOUS MODULATIONS WITH CONVOLUTION ENCODING

Directory of Open Access Journals (Sweden)

M. Raja

2011-09-01

Full Text Available This paper present a new beamforming technique using singular value decomposition (SVD for closed loop Multiple-input, multiple-output (MIMO wireless systems with various modulation techniques such as BPSK, 16-QAM, 16-PSK, DPSK and PAM along with convolution encoder. The channel matrix is decomposed into a number of independent orthogonal modes of excitation, which refer to as eigenmodes of the channel. Transmit precoding is performed by multiplying the input symbols with unitary matrix to produce the transmit beamforming, and the precoded symbols are transmitted over Rayleigh fading channel. At the receiver, combining process is performed by using maximum ratio combiner (MRC, and the receiver shaping is performed to retrieve the original input symbols by multiplying the received signal with conjugate transpose of the unitary matrix. Furthermore, the expressions for average bit error rate (BER for M-PSK and average BER for M-QAM are derived. The superiority of the proposed work is proved by simulation results and the proposed work is compared to the other beamforming methods.

Optically beamformed beam-switched adaptive antennas for fixed and mobile broadband wireless access networks

NARCIS (Netherlands)

Piqueras, M.A.; Grosskopf, G.; Vidal, B.; Herrera Llorente, J.; Martinez, J.M.; Sanchis, P.; Polo, V.; Corral, J.L.; Marceaux, A.; Galière, J.; Lopez, J.; Enard, A.; Valard, J.-L.; Parillaud, O.; Estèbe, E.; Vodjdani, N.; Choi, M.-S.; Besten, den J.H.; Soares, F.M.; Smit, M.K.; Marti, J.

2006-01-01

In this paper, a 3-bit optical beamforming architecture based in 2×2 optical switches and dispersive media is proposed and demonstrated. The performance of this photonic beamformer is experimentally demonstrated at 42.7 GHz in both transmission and reception modes. The progress achieved for

Polarized Uniform Linear Array System: Beam Radiation Pattern, Beamforming Diversity Order, and Channel Capacity

Directory of Open Access Journals (Sweden)

Xin Su

2015-01-01

Full Text Available There have been many studies regarding antenna polarization; however, there have been few publications on the analysis of the channel capacity for polarized antenna systems using the beamforming technique. According to Chung et al., the channel capacity is determined by the density of scatterers and the transmission power, which is obtained based on the assumption that scatterers are uniformly distributed on a 3D spherical scattering model. However, it contradicts the practical scenario, where scatterers may not be uniformly distributed under outdoor environment, and lacks the consideration of fading channel gain. In this study, we derive the channel capacity of polarized uniform linear array (PULA systems using the beamforming technique in a practical scattering environment. The results show that, for PULA systems, the channel capacity, which is boosted by beamforming diversity, can be determined using the channel gain, beam radiation pattern, and beamforming diversity order (BDO, where the BDO is dependent on the antenna characteristics and array configurations.

MIMO Four-Way Relaying

DEFF Research Database (Denmark)

Liu, Huaping; Sun, Fan; De Carvalho, Elisabeth

2013-01-01

Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} multiple-input multiple-output (MIMO) scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed...... the sum-rate of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with state-of-the-art reference schemes, based on two-way relaying with DF. The results indicate that the sum-rate of the two-phase four-way relaying scheme largely outperforms the four...

On Amplify-and-Forward Relaying Over Hyper-Rayleigh Fading Channels

Directory of Open Access Journals (Sweden)

S. H. Alvi

2014-12-01

Full Text Available Relayed transmission holds promise for the next generation of wireless communication systems due to the performance gains it can provide over non-cooperative systems. Recently hyper-Rayleigh fading, which represents fading conditions more severe than Rayleigh fading, has received attention in the context of many practical communication scenarios. Though power allocation for Amplify-and-Forward (AF relaying networks has been studied in the literature, a theoretical analysis of the power allocation problem for hyper-Rayleigh fading channels is a novel contribution of this work. We develop an optimal power allocation (OPA strategy for a dual-hop AF relaying network in which the relay-destination link experiences hyper-Rayleigh fading. A new closed-form expression for the average signal-to-noise ratio (SNR at destination is derived and it is shown to provide a new upper-bound on the average SNR at destination, which outperforms a previously proposed upper-bound based on the well-known harmonic-geometric mean inequality. An OPA across the source and relay nodes, subject to a sum-power constraint, is proposed and it is shown to provide measurable performance gains in average SNR and SNR outage at the destination relative to the case of equal power allocation.

Ad Hoc Microphone Array Beamforming Using the Primal-Dual Method of Multipliers

DEFF Research Database (Denmark)

Tavakoli, Vincent Mohammad; Jensen, Jesper Rindom; Heusdens, Richard

2016-01-01

In the recent years, there have been increasing amount of researches aiming at optimal beamforming with ad hoc microphone arrays, mostly with fusion-based schemes. However, huge amount of computational complexity and communication overhead impede many of these algorithms from being useful in prac...... the distributed linearly-constrained minimum variance beamformer using the the state of the art primal-dual method of multipliers. We study the proposed algorithm with an experiment....

Novel ring resonator-based integrated photonic beamformer for broadband phased array receive antennas - part 1: design and performance analysis

NARCIS (Netherlands)

Meijerink, Arjan; Roeloffzen, C.G.H.; Meijerink, Roland; Zhuang, L.; Marpaung, D.A.I.; Bentum, Marinus Jan; Burla, M.; Verpoorte, Jaco; Jorna, Pieter; Huizinga, Adriaan; van Etten, Wim

2010-01-01

A novel optical beamformer concept is introduced that can be used for seamless control of the reception angle in broadband wireless receivers employing a large phased array antenna (PAA). The core of this beamformer is an optical beamforming network (OBFN), using ring resonator-based broadband

Concentric artificial impedance surface for directional sound beamforming

Directory of Open Access Journals (Sweden)

Kyungjun Song

2017-03-01

Full Text Available Utilizing acoustic metasurfaces consisting of subwavelength resonant textures, we design an artificial impedance surface by creating a new boundary condition. We demonstrate a circular artificial impedance surface with surface impedance modulation for directional sound beamforming in three-dimensional space. This artificial impedance surface is implemented by revolving two-dimensional Helmholtz resonators with varying internal coiled path. Physically, the textured surface has inductive surface impedance on its inner circular patterns and capacitive surface impedance on its outer circular patterns. Directional receive beamforming can be achieved using an omnidirectional microphone located at the focal point formed by the gradient-impeding surface. In addition, the uniaxial surface impedance patterning inside the circular aperture can be used for steering the direction of the main lobe of the radiation pattern.

Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

KAUST Repository

Hwang, Kyusung; Ko, Youngchai; Alouini, Mohamed-Slim

2011-01-01

In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

Performance analysis of two-way amplify and forward relaying with adaptive modulation over multiple relay network

KAUST Repository

Hwang, Kyusung

2011-02-01

In this letter, we propose two-way amplify-and-forward relaying in conjunction with adaptive modulation in order to improve spectral efficiency of relayed communication systems while monitoring the required error performance. We also consider a multiple relay network where only the best relay node is utilized so that the diversity order increases while maintaining a low complexity of implementation as the number of relays increases. Based on the best relay selection criterion, we offer an upper bound on the signal-to-noise ratio to keep the performance analysis tractable. Our numerical examples show that the proposed system offers a considerable gain in spectral efficiency while satisfying the error rate requirements. © 2011 IEEE.

Opportunistic Relay Selection With Limited Feedback

KAUST Repository

Eltayeb, Mohammed E.

2015-08-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Generally, relay selection algorithms require channel state information (CSI) feedback from all cooperating relays to make a selection decision. This requirement poses two important challenges, which are often neglected in the literature. Firstly, the fed back channel information is usually corrupted by additive noise. Secondly, CSI feedback generates a great deal of feedback overhead (air-time) that could result in significant performance hits. In this paper, we propose a compressive sensing (CS) based relay selection algorithm that reduces the feedback overhead of relay networks under the assumption of noisy feedback channels. The proposed algorithm exploits CS to first obtain the identity of a set of relays with favorable channel conditions. Following that, the CSI of the identified relays is estimated using least squares estimation without any additional feedback. Both single and multiple relay selection cases are considered. After deriving closed-form expressions for the asymptotic end-to-end SNR at the destination and the feedback load for different relaying protocols, we show that CS-based selection drastically reduces the feedback load and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback. © 1972-2012 IEEE.

Tightness of Semidefinite Programming Relaxation to Robust Transmit Beamforming with SINR Constraints

Directory of Open Access Journals (Sweden)

Yanjun Wang

2013-01-01

Full Text Available This paper considers a multiuser transmit beamforming problem under uncertain channel state information (CSI subject to SINR constraints in a downlink multiuser MISO system. A robust transmit beamforming formulation is proposed. This robust formulation is to minimize the transmission power subject to worst-case signal-to-interference-plus-noise ratio (SINR constraints on the receivers. The challenging problem is that the worst-case SINR constraints correspond to an infinite number of nonconvex quadratic constraints. In this paper, a natural semidifinite programming (SDP relaxation problem is proposed to solve the robust beamforming problem. The main contribution of this paper is to establish the tightness of the SDP relaxation problem under proper assumption, which means that the SDP relaxation problem definitely yields rank-one solutions under the assumption. Then the SDP relaxation problem provides globally optimum solutions of the primal robust transmit beamforming problem under proper assumption and norm-constrained CSI errors. Simulation results show the correctness of the proposed theoretical results and also provide a counterexample whose solutions are not rank one. The existence of counterexample shows that the guess that the solutions of the SDP relaxation problem must be rank one is wrong, except that some assumptions (such as the one proposed in this paper hold.

Ready, steady… relay!

CERN Multimedia

2008-01-01

Thursday 5 June. With another year comes another success for CERN’s Relay Race. With 76 teams taking part it was the second highest turnout in the race’s history. ‘The Shabbys’ won the relay race in 10 minutes 51 seconds.As popular as ever, this year the relay race took on the atmosphere of a mini carnival. Gathering on the lawn outside Restaurant 1, various stalls and attractions added to the party feeling of the event, with beer courtesy of ‘AGLUP’, the Belgian beer club, and a wandering jazz group entertaining spectators and competitors alike. Reflecting the greater involvement of other associations in the relay race, the president of the Staff Association Clubs Committee, James Purvis, was the guest of honour, launching the start of the race and presenting the prizes. As regular followers of the race could have probably predicted, The Shabbys were once again victorious and claimed first place. The team members th...

Transmit power optimization for green multihop relaying over Nakagami-m fading channels

KAUST Repository

Randrianantenaina, Itsikiantsoa

2014-03-01

In this paper, we investigate the optimal transmit power strategy to maximize the energy efficiency of a multihop relaying network. Considering the communication between a source and a destination through multiple Amplify-and-Forward relays, we first give the expression of the total instantaneous system energy consumption. Then, we define the energy efficiency in our context and obtain its expression in closed-form when the communication is over Nakagami-m fading channels. The analysis yields to the derivation of a global transmit power strategy where each individual node is contributing to the end-to-end overall energy efficiency. Numercial results are presented to illustrate the analysis. Comparison with Monte Carlo simulation results confirms the accuracy of our derivations, and assesses the gains of the proposed power optimization strategy. © 2014 IEEE.

Transmit power optimization for green multihop relaying over Nakagami-m fading channels

KAUST Repository

Randrianantenaina, Itsikiantsoa; Benjillali, Mustapha; Alouini, Mohamed-Slim

2014-01-01

In this paper, we investigate the optimal transmit power strategy to maximize the energy efficiency of a multihop relaying network. Considering the communication between a source and a destination through multiple Amplify-and-Forward relays, we first give the expression of the total instantaneous system energy consumption. Then, we define the energy efficiency in our context and obtain its expression in closed-form when the communication is over Nakagami-m fading channels. The analysis yields to the derivation of a global transmit power strategy where each individual node is contributing to the end-to-end overall energy efficiency. Numercial results are presented to illustrate the analysis. Comparison with Monte Carlo simulation results confirms the accuracy of our derivations, and assesses the gains of the proposed power optimization strategy. © 2014 IEEE.

Microcomb-Based True-Time-Delay Network for Microwave Beamforming With Arbitrary Beam Pattern Control

Science.gov (United States)

Xue, Xiaoxiao; Xuan, Yi; Bao, Chengying; Li, Shangyuan; Zheng, Xiaoping; Zhou, Bingkun; Qi, Minghao; Weiner, Andrew M.

2018-06-01

Microwave phased array antennas (PAAs) are very attractive to defense applications and high-speed wireless communications for their abilities of fast beam scanning and complex beam pattern control. However, traditional PAAs based on phase shifters suffer from the beam-squint problem and have limited bandwidths. True-time-delay (TTD) beamforming based on low-loss photonic delay lines can solve this problem. But it is still quite challenging to build large-scale photonic TTD beamformers due to their high hardware complexity. In this paper, we demonstrate a photonic TTD beamforming network based on a miniature microresonator frequency comb (microcomb) source and dispersive time delay. A method incorporating optical phase modulation and programmable spectral shaping is proposed for positive and negative apodization weighting to achieve arbitrary microwave beam pattern control. The experimentally demonstrated TTD beamforming network can support a PAA with 21 elements. The microwave frequency range is $\\mathbf{8\\sim20\\ {GHz}}$, and the beam scanning range is $\\mathbf{\\pm 60.2^\\circ}$. Detailed measurements of the microwave amplitudes and phases are performed. The beamforming performances of Gaussian, rectangular beams and beam notch steering are evaluated through simulations by assuming a uniform radiating antenna array. The scheme can potentially support larger PAAs with hundreds of elements by increasing the number of comb lines with broadband microcomb generation.

A genetic algorithm for multiple relay selection in two-way relaying cognitive radio networks

KAUST Repository

Alsharoa, Ahmad M.

2013-09-01

In this paper, we investigate a multiple relay selection scheme for two-way relaying cognitive radio networks where primary users and secondary users operate on the same frequency band. More specifically, cooperative relays using Amplifyand- Forward (AF) protocol are optimally selected to maximize the sum rate of the secondary users without degrading the Quality of Service (QoS) of the primary users by respecting a tolerated interference threshold. A strong optimization tool based on genetic algorithm is employed to solve our formulated optimization problem where discrete relay power levels are considered. Our simulation results show that the practical heuristic approach achieves almost the same performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions. Copyright © 2013 by the Institute of Electrical and Electronic Engineers, Inc.

Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

KAUST Repository

Nam, Sung Sik

2018-01-09

In this work, we propose an iterative relay scheduling with hybrid ARQ (IRS-HARQ) scheme which realizes fast jump-in/successive relaying and subframe-based decoding under the multiple user equipment (UE) relay environments applicable to the next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user link should be operated in an open-loop and transparent mode. The latter is due to the fact that not only there are no dedicated control channels between the UE relay and the end user but also a new cell is not created. Under this open-loop and transparent mode, our proposed protocol is implemented by partially exploiting the channel state information based on the overhearing mechanism of ACK/NACK for HARQ. Further, the iterative scheduling enables UE-to-UE direct communication with proximity that offers spatial frequency reuse and energy saving.

Relay Selection with Limited and Noisy Feedback

KAUST Repository

Eltayeb, Mohammed E.

2016-01-28

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI acquisition generates a great deal of feedback overhead that could result in significant transmission delays. In addition to this, the fed back channel information is usually corrupted by additive noise. This could lead to transmission outages if the central node selects the set of cooperating relays based on inaccurate feedback information. In this paper, we propose a relay selection algorithm that tackles the above challenges. Instead of allocating each relay a dedicated channel for feedback, all relays share a pool of feedback channels. Following that, each relay feeds back its identity only if its effective channel (source-relay-destination) exceeds a threshold. After deriving closed-form expressions for the feedback load and the achievable rate, we show that the proposed algorithm drastically reduces the feedback overhead and achieves a rate close to that obtained by selection algorithms with dedicated error-free feedback from all relays. © 2015 IEEE.

Uplink transmit beamforming design for SINR maximization with full multiuser channel state information

Science.gov (United States)

Xi, Songnan; Zoltowski, Michael D.

2008-04-01

Multiuser multiple-input multiple-output (MIMO) systems are considered in this paper. We continue our research on uplink transmit beamforming design for multiple users under the assumption that the full multiuser channel state information, which is the collection of the channel state information between each of the users and the base station, is known not only to the receiver but also to all the transmitters. We propose an algorithm for designing optimal beamforming weights in terms of maximizing the signal-to-interference-plus-noise ratio (SINR). Through statistical modeling, we decouple the original mathematically intractable optimization problem and achieved a closed-form solution. As in our previous work, the minimum mean-squared error (MMSE) receiver with successive interference cancellation (SIC) is adopted for multiuser detection. The proposed scheme is compared with an existing jointly optimized transceiver design, referred to as the joint transceiver in this paper, and our previously proposed eigen-beamforming algorithm. Simulation results demonstrate that our algorithm, with much less computational burden, accomplishes almost the same performance as the joint transceiver for spatially independent MIMO channel and even better performance for spatially correlated MIMO channels. And it always works better than our previously proposed eigen beamforming algorithm.

A comparison between temporal and subband minimum variance adaptive beamforming

Science.gov (United States)

Diamantis, Konstantinos; Voxen, Iben H.; Greenaway, Alan H.; Anderson, Tom; Jensen, Jørgen A.; Sboros, Vassilis

2014-03-01

This paper compares the performance between temporal and subband Minimum Variance (MV) beamformers for medical ultrasound imaging. Both adaptive methods provide an optimized set of apodization weights but are implemented in the time and frequency domains respectively. Their performance is evaluated with simulated synthetic aperture data obtained from Field II and is quantified by the Full-Width-Half-Maximum (FWHM), the Peak-Side-Lobe level (PSL) and the contrast level. From a point phantom, a full sequence of 128 emissions with one transducer element transmitting and all 128 elements receiving each time, provides a FWHM of 0.03 mm (0.14λ) for both implementations at a depth of 40 mm. This value is more than 20 times lower than the one achieved by conventional beamforming. The corresponding values of PSL are -58 dB and -63 dB for time and frequency domain MV beamformers, while a value no lower than -50 dB can be obtained from either Boxcar or Hanning weights. Interestingly, a single emission with central element #64 as the transmitting aperture provides results comparable to the full sequence. The values of FWHM are 0.04 mm and 0.03 mm and those of PSL are -42 dB and -46 dB for temporal and subband approaches. From a cyst phantom and for 128 emissions, the contrast level is calculated at -54 dB and -63 dB respectively at the same depth, with the initial shape of the cyst being preserved in contrast to conventional beamforming. The difference between the two adaptive beamformers is less significant in the case of a single emission, with the contrast level being estimated at -42 dB for the time domain and -43 dB for the frequency domain implementation. For the estimation of a single MV weight of a low resolution image formed by a single emission, 0.44 * 109 calculations per second are required for the temporal approach. The same numbers for the subband approach are 0.62 * 109 for the point and 1.33 * 109 for the cyst phantom. The comparison demonstrates similar

Beamforming using subspace estimation from a diagonally averaged sample covariance.

Science.gov (United States)

Quijano, Jorge E; Zurk, Lisa M

2017-08-01

The potential benefit of a large-aperture sonar array for high resolution target localization is often challenged by the lack of sufficient data required for adaptive beamforming. This paper introduces a Toeplitz-constrained estimator of the clairvoyant signal covariance matrix corresponding to multiple far-field targets embedded in background isotropic noise. The estimator is obtained by averaging along subdiagonals of the sample covariance matrix, followed by covariance extrapolation using the method of maximum entropy. The sample covariance is computed from limited data snapshots, a situation commonly encountered with large-aperture arrays in environments characterized by short periods of local stationarity. Eigenvectors computed from the Toeplitz-constrained covariance are used to construct signal-subspace projector matrices, which are shown to reduce background noise and improve detection of closely spaced targets when applied to subspace beamforming. Monte Carlo simulations corresponding to increasing array aperture suggest convergence of the proposed projector to the clairvoyant signal projector, thereby outperforming the classic projector obtained from the sample eigenvectors. Beamforming performance of the proposed method is analyzed using simulated data, as well as experimental data from the Shallow Water Array Performance experiment.

Performance analysis of distributed beamforming in a spectrum sharing system

KAUST Repository

Yang, Liang; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2012-01-01

In this paper, we consider a distributed beamforming scheme (DBF) in a spectrum sharing system where multiple secondary users share the spectrum with the licensed primary users under an interference temperature constraint. We assume that DBF is applied at the secondary users. We first consider optimal beamforming and compare it with the user selection scheme in terms of the outage probability and bit-error rate performance. Since perfect feedback is difficult to obtain, we then investigate a limited feedback DBF scheme and develop an outage probability analysis for a random vector quantization (RVQ) design algorithm. Numerical results are provided to illustrate our mathematical formalism and verify our analysis. © 2012 IEEE.

Performance analysis of distributed beamforming in a spectrum sharing system

KAUST Repository

Yang, Liang

2012-09-01

In this paper, we consider a distributed beamforming scheme (DBF) in a spectrum sharing system where multiple secondary users share the spectrum with the licensed primary users under an interference temperature constraint. We assume that DBF is applied at the secondary users. We first consider optimal beamforming and compare it with the user selection scheme in terms of the outage probability and bit-error rate performance. Since perfect feedback is difficult to obtain, we then investigate a limited feedback DBF scheme and develop an outage probability analysis for a random vector quantization (RVQ) design algorithm. Numerical results are provided to illustrate our mathematical formalism and verify our analysis. © 2012 IEEE.

Optimal relay selection and power allocation for cognitive two-way relaying networks

KAUST Repository

Pandarakkottilil, Ubaidulla; Aï ssa, Sonia

2012-01-01

In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays

Buffer-Aided Relaying with Adaptive Link Selection

DEFF Research Database (Denmark)

Zlatanov, Nikola; Schober, Robert; Popovski, Petar

2013-01-01

In this paper, we consider a simple network consisting of a source, a half-duplex decode-and-forward relay, and a destination. We propose a new relaying protocol employing adaptive link selection, i.e., in any given time slot, based on the channel state information of the source-relay and the relay......-destination link a decision is made whether the source or the relay transmits. In order to avoid data loss at the relay, adaptive link selection requires the relay to be equipped with a buffer such that data can be queued until the relay-destination link is selected for transmission. We study both delay......-constrained and delay-unconstrained transmission. For the delay-unconstrained case, we characterize the optimal link selection policy, derive the corresponding throughput, and develop an optimal power allocation scheme. For the delay-constrained case, we propose to starve the buffer of the relay by choosing...

Aliasing-free wideband beamforming using sparse signal representation

NARCIS (Netherlands)

Tang, Z.; Blacquière, G.; Leus, G.

2011-01-01

Sparse signal representation (SSR) is considered to be an appealing alternative to classical beamforming for direction-of-arrival (DOA) estimation. For wideband signals, the SSR-based approach constructs steering matrices, referred to as dictionaries in this paper, corresponding to different

Model-based iterative learning control of Parkinsonian state in thalamic relay neuron

Science.gov (United States)

Liu, Chen; Wang, Jiang; Li, Huiyan; Xue, Zhiqin; Deng, Bin; Wei, Xile

2014-09-01

Although the beneficial effects of chronic deep brain stimulation on Parkinson's disease motor symptoms are now largely confirmed, the underlying mechanisms behind deep brain stimulation remain unclear and under debate. Hence, the selection of stimulation parameters is full of challenges. Additionally, due to the complexity of neural system, together with omnipresent noises, the accurate model of thalamic relay neuron is unknown. Thus, the iterative learning control of the thalamic relay neuron's Parkinsonian state based on various variables is presented. Combining the iterative learning control with typical proportional-integral control algorithm, a novel and efficient control strategy is proposed, which does not require any particular knowledge on the detailed physiological characteristics of cortico-basal ganglia-thalamocortical loop and can automatically adjust the stimulation parameters. Simulation results demonstrate the feasibility of the proposed control strategy to restore the fidelity of thalamic relay in the Parkinsonian condition. Furthermore, through changing the important parameter—the maximum ionic conductance densities of low-threshold calcium current, the dominant characteristic of the proposed method which is independent of the accurate model can be further verified.

Relay Selection with Limited and Noisy Feedback

KAUST Repository

Eltayeb, Mohammed E.; Elkhalil, Khalil; Mas'ud, Abdullahi Abubakar; Al-Naffouri, Tareq Y.

2016-01-01

Relay selection is a simple technique that achieves spatial diversity in cooperative relay networks. Nonetheless, relay selection algorithms generally require error-free channel state information (CSI) from all cooperating relays. Practically, CSI

CERN Relay Race

CERN Multimedia

2009-01-01

The CERN relay race, now in its 39th year, is already a well-known tradition, but this year the organizers say the event will have even more of a festival feeling. Just off the starting line of the CERN relay race.For the past few years, spectators and runners at the CERN relay race have been able to enjoy a beer while listening to music from the CERN music and jazz clubs. But this year the organizers are aiming for "even more of a festival atmosphere". As David Nisbet, President of the CERN running club and organizer of the relay race, says: "Work is not just about getting your head down and doing the theory, it’s also about enjoying the company of your colleagues." This year, on top of music from the Santa Luis Band and the Canettes Blues Band, there will be demonstrations from the Aikido and softball clubs, a stretching session by the Fitness club, as well as various stalls and of course, the well-earned beer from AGLUP, the B...

Directional hearing aid using hybrid adaptive beamformer (HAB) and binaural ITE array

Science.gov (United States)

Shaw, Scott T.; Larow, Andy J.; Gibian, Gary L.; Sherlock, Laguinn P.; Schulein, Robert

2002-05-01

A directional hearing aid algorithm called the Hybrid Adaptive Beamformer (HAB), developed for NIH/NIA, can be applied to many different microphone array configurations. In this project the HAB algorithm was applied to a new array employing in-the-ear microphones at each ear (HAB-ITE), to see if previous HAB performance could be achieved with a more cosmetically acceptable package. With diotic output, the average benefit in threshold SNR was 10.9 dB for three HoH and 11.7 dB for five normal-hearing subjects. These results are slightly better than previous results of equivalent tests with a 3-in. array. With an innovative binaural fitting, a small benefit beyond that provided by diotic adaptive beamforming was observed: 12.5 dB for HoH and 13.3 dB for normal-hearing subjects, a 1.6 dB improvement over the diotic presentation. Subjectively, the binaural fitting preserved binaural hearing abilities, giving the user a sense of space, and providing left-right localization. Thus the goal of creating an adaptive beamformer that simultaneously provides excellent noise reduction and binaural hearing was achieved. Further work remains before the HAB-ITE can be incorporated into a real product, optimizing binaural adaptive beamforming, and integrating the concept with other technologies to produce a viable product prototype. [Work supported by NIH/NIDCD.

Physical Layer Security Using Two-Path Successive Relaying

Directory of Open Access Journals (Sweden)

Qian Yu Liau

2016-06-01

Full Text Available Relaying is one of the useful techniques to enhance wireless physical-layer security. Existing literature shows that employing full-duplex relay instead of conventional half-duplex relay improves secrecy capacity and secrecy outage probability, but this is at the price of sophisticated implementation. As an alternative, two-path successive relaying has been proposed to emulate operation of full-duplex relay by scheduling a pair of half-duplex relays to assist the source transmission alternately. However, the performance of two-path successive relaying in secrecy communication remains unexplored. This paper proposes a secrecy two-path successive relaying protocol for a scenario with one source, one destination and two half-duplex relays. The relays operate alternately in a time division mode to forward messages continuously from source to destination in the presence of an eavesdropper. Analytical results reveal that the use of two half-duplex relays in the proposed scheme contributes towards a quadratically lower probability of interception compared to full-duplex relaying. Numerical simulations show that the proposed protocol achieves the ergodic achievable secrecy rate of full-duplex relaying while delivering the lowest probability of interception and secrecy outage probability compared to the existing half duplex relaying, full duplex relaying and full duplex jamming schemes.

Resource allocation for transmit hybrid beamforming in decoupled millimeter wave multiuser-MIMO downlink

OpenAIRE

Ahmed, Irfan; Khammari, Hedi; Shahid, Adnan

2017-01-01

This paper presents a study on joint radio resource allocation and hybrid precoding in multicarrier massive multiple-input multiple-output communications for 5G cellular networks. In this paper, we present the resource allocation algorithm to maximize the proportional fairness (PF) spectral efficiency under the per subchannel power and the beamforming rank constraints. Two heuristic algorithms are designed. The proportional fairness hybrid beamforming algorithm provides the transmit precoder ...

Indoor Off-Body Wireless Communication: Static Beamforming versus Space-Time Coding

Directory of Open Access Journals (Sweden)

Patrick Van Torre

2012-01-01

Full Text Available The performance of beamforming versus space-time coding using a body-worn textile antenna array is experimentally evaluated for an indoor environment, where a walking rescue worker transmits data in the 2.45 GHz ISM band, relying on a vertical textile four-antenna array integrated into his garment. The two transmission scenarios considered are static beamforming at low-elevation angles and space-time code based transmit diversity. Signals are received by a base station equipped with a horizontal array of four dipole antennas providing spatial receive diversity through maximum-ratio combining. Signal-to-noise ratios, bit error rate characteristics, and signal correlation properties are assessed for both off-body transmission scenarios. Without receiver diversity, the performance of space-time coding is generally better. In case of fourth-order receiver diversity, beamforming is superior in line-of-sight conditions. For non-line-of-sight propagation, the space-time codes perform better as soon as bit error rates are low enough for a reliable data link.

Handover Framework for Relay Enhanced LTE Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Van Phan, Vinh; Raaf, Bernhard

2009-01-01

Relaying is one of the proposed technologies for future releases of UTRAN Long Term Evolution (LTE) networks. Introducing relaying is expected to increase the coverage and capacity of LTE networks. In order to enable relaying, the architecture, protocol and radio resource management procedures...... of LTE, such as handover, have to be modified. A user can be handed over not only between two base stations, but also between relays and base stations, and between two relays. With the introduction of relaying, there is a need for a new procedure to hand over a relay and all its associated users...... to another base station, allowing a flexible and dynamic relay deployment. In this paper, we extend the LTE release 8 handover mechanisms so that it can accommodate these new handover functionalities in a flexible manner....

Optimal relay selection and power allocation for cognitive two-way relaying networks

KAUST Repository

Pandarakkottilil, Ubaidulla

2012-06-01

In this paper, we present an optimal scheme for power allocation and relay selection in a cognitive radio network where a pair of cognitive (or secondary) transceiver nodes communicate with each other assisted by a set of cognitive two-way relays. The secondary nodes share the spectrum with a licensed primary user (PU), and each node is assumed to be equipped with a single transmit/receive antenna. The interference to the PU resulting from the transmission from the cognitive nodes is kept below a specified limit. We propose joint relay selection and optimal power allocation among the secondary user (SU) nodes achieving maximum throughput under transmit power and PU interference constraints. A closed-form solution for optimal allocation of transmit power among the SU transceivers and the SU relay is presented. Furthermore, numerical simulations and comparisons are presented to illustrate the performance of the proposed scheme. © 2012 IEEE.

Multidimensional-DSP Beamformers Using the ROACH-2 FPGA Platform

Directory of Open Access Journals (Sweden)

Vishwa Seneviratne

2017-07-01

Full Text Available Antenna array-based multi-dimensional infinite-impulse response (IIR digital beamformers are employed in a multitude of radio frequency (RF applications ranging from electronically-scanned radar, radio telescopes, long-range detection and target tracking. A method to design 3D IIR beam filters using 2D IIR beam filters is described. A cascaded 2D IIR beam filter architecture is proposed based on systolic array architecture as an alternative for an existing radar application. Differential-form transfer function and polyphase structures are employed in the design to gain an increase in the speed of operation to gigahertz range. The feasibility of practical implementation of a 4-phase polyphase 2D IIR beam filter is explored. A digital hardware prototype is designed, implemented and tested using a ROACH-2 Field Programmable Gate Array (FPGA platform fitted with a Xilinx Virtex-6 SX475T FPGA chip and multi-input analog-to-digital converters (ADC boards set to a maximum sampling rate of 960 MHz. The article describes a method to build a 3D IIR beamformer using polyphase structures. A comparison of technical specifications of an existing radar application based on phased-array and the proposed 3D IIR beamformer is also explained to illustrate the proposed method to be a better alternative for such applications.

In Vivo Evaluation of Synthetic Aperture Sequential Beamforming

DEFF Research Database (Denmark)

Hemmsen, Martin Christian; Hansen, Peter Møller; Lange, Theis

2012-01-01

Ultrasound in vivo imaging using synthetic aperture sequential beamformation (SASB) is compared with conventional imaging in a double blinded study using side-by-side comparisons. The objective is to evaluate if the image quality in terms of penetration depth, spatial resolution, contrast...

Synthetic aperture ultrasound Fourier beamformation using virtual sources

DEFF Research Database (Denmark)

Moghimirad, Elahe; Villagómez Hoyos, Carlos Armando; Mahloojifar, Ali

2016-01-01

An efficient Fourier beamformation algorithm is presented for multistatic synthetic aperture ultrasound imaging using virtual sources (FBV). The concept is based on the frequency domain wavenumber algorithm from radar and sonar and is extended to a multi-element transmit/receive configuration using...

Application of a Beamforming Technique to the Measurement of Airfoil Leading Edge Noise

Directory of Open Access Journals (Sweden)

Thomas Geyer

2012-01-01

Full Text Available The present paper describes the use of microphone array technology and beamforming algorithms for the measurement and analysis of noise generated by the interaction of a turbulent flow with the leading edge of an airfoil. Experiments were performed using a setup in an aeroacoustic wind tunnel, where the turbulent inflow is provided by different grids. In order to exactly localize the aeroacoustic noise sources and, moreover, to separate airfoil leading edge noise from grid-generated noise, the selected deconvolution beamforming algorithm is extended to be used on a fully three-dimensional source region. The result of this extended beamforming are three-dimensional mappings of noise source locations. Besides acoustic measurements, the investigation of airfoil leading edge noise requires the measurement of parameters describing the incident turbulence, such as the intensity and a characteristic length scale or time scale. The method used for the determination of these parameters in the present study is explained in detail. To demonstrate the applicability of the extended beamforming algorithm and the experimental setup as a whole, the noise generated at the leading edge of airfoils made of porous materials was measured and compared to that generated at the leading edge of a common nonporous airfoil.

Improved Plane-Wave Ultrasound Beamforming by Incorporating Angular Weighting and Coherent Compounding in Fourier Domain.

Science.gov (United States)

Chen, Chuan; Hendriks, Gijs A G M; van Sloun, Ruud J G; Hansen, Hendrik H G; de Korte, Chris L

2018-05-01

In this paper, a novel processing framework is introduced for Fourier-domain beamforming of plane-wave ultrasound data, which incorporates coherent compounding and angular weighting in the Fourier domain. Angular weighting implies spectral weighting by a 2-D steering-angle-dependent filtering template. The design of this filter is also optimized as part of this paper. Two widely used Fourier-domain plane-wave ultrasound beamforming methods, i.e., Lu's f-k and Stolt's f-k methods, were integrated in the framework. To enable coherent compounding in Fourier domain for the Stolt's f-k method, the original Stolt's f-k method was modified to achieve alignment of the spectra for different steering angles in k-space. The performance of the framework was compared for both methods with and without angular weighting using experimentally obtained data sets (phantom and in vivo), and data sets (phantom) provided by the IEEE IUS 2016 plane-wave beamforming challenge. The addition of angular weighting enhanced the image contrast while preserving image resolution. This resulted in images of equal quality as those obtained by conventionally used delay-and-sum (DAS) beamforming with apodization and coherent compounding. Given the lower computational load of the proposed framework compared to DAS, to our knowledge it can, therefore, be concluded that it outperforms commonly used beamforming methods such as Stolt's f-k, Lu's f-k, and DAS.

Experimental performance assessment of the sub-band minimum variance beamformer for ultrasound imaging

DEFF Research Database (Denmark)

Diamantis, Konstantinos; Greenaway, Alan H.; Anderson, Tom

2017-01-01

Recent progress in adaptive beamforming techniques for medical ultrasound has shown that current resolution limits can be surpassed. One method of obtaining improved lateral resolution is the Minimum Variance (MV) beamformer. The frequency domain implementation of this method effectively divides...... the broadband ultrasound signals into sub-bands (MVS) to conform with the narrow-band assumption of the original MV theory. This approach is investigated here using experimental Synthetic Aperture (SA) data from wire and cyst phantoms. A 7 MHz linear array transducer is used with the SARUS experimental...... ultrasound scanner for the data acquisition. The lateral resolution and the contrast obtained, are evaluated and compared with those from the conventional Delay-and-Sum (DAS) beamformer and the MV temporal implementation (MVT). From the wire phantom the Full-Width-at-Half-Maximum (FWHM) measured at a depth...

Full-Duplex Relay Selection in Cognitive Underlay Networks

KAUST Repository

Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aissa, Sonia

2017-01-01

In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby

Speech understanding in background noise with the two-microphone adaptive beamformer BEAM in the Nucleus Freedom Cochlear Implant System.

Science.gov (United States)

Spriet, Ann; Van Deun, Lieselot; Eftaxiadis, Kyriaky; Laneau, Johan; Moonen, Marc; van Dijk, Bas; van Wieringen, Astrid; Wouters, Jan

2007-02-01

This paper evaluates the benefit of the two-microphone adaptive beamformer BEAM in the Nucleus Freedom cochlear implant (CI) system for speech understanding in background noise by CI users. A double-blind evaluation of the two-microphone adaptive beamformer BEAM and a hardware directional microphone was carried out with five adult Nucleus CI users. The test procedure consisted of a pre- and post-test in the lab and a 2-wk trial period at home. In the pre- and post-test, the speech reception threshold (SRT) with sentences and the percentage correct phoneme scores for CVC words were measured in quiet and background noise at different signal-to-noise ratios. Performance was assessed for two different noise configurations (with a single noise source and with three noise sources) and two different noise materials (stationary speech-weighted noise and multitalker babble). During the 2-wk trial period at home, the CI users evaluated the noise reduction performance in different listening conditions by means of the SSQ questionnaire. In addition to the perceptual evaluation, the noise reduction performance of the beamformer was measured physically as a function of the direction of the noise source. Significant improvements of both the SRT in noise (average improvement of 5-16 dB) and the percentage correct phoneme scores (average improvement of 10-41%) were observed with BEAM compared to the standard hardware directional microphone. In addition, the SSQ questionnaire and subjective evaluation in controlled and real-life scenarios suggested a possible preference for the beamformer in noisy environments. The evaluation demonstrates that the adaptive noise reduction algorithm BEAM in the Nucleus Freedom CI-system may significantly increase the speech perception by cochlear implantees in noisy listening conditions. This is the first monolateral (adaptive) noise reduction strategy actually implemented in a mainstream commercial CI.

Synthetic Aperture Flow Imaging Using a Dual Beamformer Approach

DEFF Research Database (Denmark)

Li, Ye

Color flow mapping systems have become widely used in clinical applications. It provides an opportunity to visualize the velocity profile over a large region in the vessel, which makes it possible to diagnose, e.g., occlusion of veins, heart valve deficiencies, and other hemodynamic problems....... However, while the conventional ultrasound imaging of making color flow mapping provides useful information in many circumstances, the spatial velocity resolution and frame rate are limited. The entire velocity distribution consists of image lines from different directions, and each image line...... on the current commercial ultrasound scanner. The motivation for this project is to develop a method lowering the amount of calculations and still maintaining beamforming quality sufficient for flow estimation. Synthetic aperture using a dual beamformer approach is investigated using Field II simulations...

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar

2017-03-14

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar; Shaqfeh, Mohammad; Alnuweiri, Hussein; Alouini, Mohamed-Slim

2017-01-01

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Adaptive Port-Starboard Beamforming of Triplet Sonar Arrays

NARCIS (Netherlands)

Groen, J.; Beerens, S.P.; Been, R.; Doisy, Y.

2005-01-01

Abstract—For a low-frequency active sonar (LFAS) with a triplet receiver array, it is not clear in advance which signal processing techniques optimize its performance. Here, several advanced beamformers are analyzed theoretically, and the results are compared to experimental data obtained in sea

Adaptive Beamforming Algorithms for Tow Ship Noise Canceling

NARCIS (Netherlands)

Robert, M.K.; Beerens, S.P.

2002-01-01

In towed array sonar, the directional noise originating from the tow ship, mainly machinery and hydrodynamic noise, often limits the sonar performance. When processed with classical beamforming techniques, loud tow ship noise induces high sidelobes that may hide detection of quiet targets in forward

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond.

Science.gov (United States)

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2016-01-01

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment.

Performance analysis of opportunistic nonregenerative relaying

KAUST Repository

Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.; Yang, Hongchuan

2013-01-01

Opportunistic relaying in cooperative communication depends on careful relay selection. However, the traditional centralized method used for opportunistic amplify-and-forward protocols requires precise measurements of channel state information at the destination. In this paper, we adopt the max-min criterion as a relay selection framework for opportunistic amplify-and-forward cooperative communications, which was exhaustively used for the decode-and-forward protocol, and offer an accurate performance analysis based on exact statistics of the local signal-to-noise ratios of the best relay. Furthermore, we evaluate the asymptotical performance and deduce the diversity order of our proposed scheme. Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over Rayleigh fading channels, and we compare the max-min relay selection with their centralized channel state information-based and partial relay selection counterparts.

A New Codebook Design for Hybrid Beamforming Systems using ...

African Journals Online (AJOL)

pc

2018-03-05

Mar 5, 2018 ... wireless personal area networks (WPANs) operating at the ... antenna element, is not practical in terms of the cost and power consumption [4]. To overcome ... hybrid beamformers for data transmission were designed under.

Energy efficient circuit design using nanoelectromechanical relays

Science.gov (United States)

Venkatasubramanian, Ramakrishnan

Nano-electromechanical (NEM) relays are a promising class of emerging devices that offer zero off-state leakage and behave like an ideal switch. Recent advances in planar fabrication technology have demonstrated that microelectromechanical (MEMS) scale miniature relays could be manufactured reliably and could be used to build fully functional, complex integrated circuits. The zero leakage operation of relays has renewed the interest in relay based low power logic design. This dissertation explores circuit architectures using NEM relays and NEMS-CMOS heterogeneous integration. Novel circuit topologies for sequential logic, memory, and power management circuits have been proposed taking into consideration the NEM relay device properties and optimizing for energy efficiency and area. In nanoscale electromechanical devices, dispersion forces like Van der Waals' force (vdW) affect the pull-in stability of the relay devices significantly. Verilog-A electromechanical model of the suspended gate relay operating at 1V with a nominal air gap of 5 - 10nm has been developed taking into account all the electrical, mechanical and dispersion effects. This dissertation explores different relay based latch and flip-flop topologies. It has been shown that as few as 4 relay cells could be used to build flip-flops. An integrated voltage doubler based flip flop that improves the performance by 2X by overdriving Vgb has been proposed. Three NEM relay based parallel readout memory bitcell architectures have been proposed that have faster access time, and remove the reliability issues associated with previously reported serial readout architectures. A paradigm shift in design of power switches using NEM relays is proposed. An interesting property of the relay device is that the ON state resistance (Ron) of the NEM relay switch is constant and is insensitive to the gate slew rate. This coupled with infinite OFF state resistance (Roff ) offers significant area and power advantages over CMOS

78 FR 40407 - Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and...

Science.gov (United States)

2013-07-05

...] Structure and Practices of the Video Relay Service Program: Telecommunications Relay Services and Speech-to... telecommunications relay services (TRS) program continues to offer functional equivalence to all eligible users and..., identified by CG Docket Nos. 10-51 and 03-123, by any of the following methods: Electronic Filers: Comments...

Mobile Ultrasound Plane Wave Beamforming on iPhone or iPad using Metal- based GPU Processing

Science.gov (United States)

Hewener, Holger J.; Tretbar, Steffen H.

Mobile and cost effective ultrasound devices are being used in point of care scenarios or the drama room. To reduce the costs of such devices we already presented the possibilities of consumer devices like the Apple iPad for full signal processing of raw data for ultrasound image generation. Using technologies like plane wave imaging to generate a full image with only one excitation/reception event the acquisition times and power consumption of ultrasound imaging can be reduced for low power mobile devices based on consumer electronics realizing the transition from FPGA or ASIC based beamforming into more flexible software beamforming. The massive parallel beamforming processing can be done with the Apple framework "Metal" for advanced graphics and general purpose GPU processing for the iOS platform. We were able to integrate the beamforming reconstruction into our mobile ultrasound processing application with imaging rates up to 70 Hz on iPad Air 2 hardware.

Digitally assisted analog beamforming for millimeter-wave communication

NARCIS (Netherlands)

Kokkeler, Andre B.J.; Smit, Gerardus Johannes Maria

2015-01-01

The paper addresses the research question on how digital beamsteering algorithms can be combined with analog beamforming in the context of millimeter-wave communication for next generation (5G) cellular systems. Key is the use of coarse quantisation of the individual antenna signals next to the

Relay test program

International Nuclear Information System (INIS)

Bandyopadhyay, K.K.; Kunkel, C.; Shteyngart, S.

1994-02-01

This report presents the results of a relay test program conducted by Brookhaven National Laboratory (BNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC). The program is a continuation of an earlier test program the results of which were published in NUREG/CR-4867. The current program was carried out in two phases: electrical testing and vibration testing. The objective was primarily to focus on the electrical discontinuity or continuity of relays and circuit breaker tripping mechanisms subjected to electrical pulses and vibration loads. The electrical testing was conducted by KEMA-Powertest Company and the vibration testing was performed at Wyle Laboratories, Huntsville, Alabama. This report discusses the test procedures, presents the test data, includes an analysis of the data and provides recommendations regarding reliable relay testing

Low complexity symbol-wise beamforming for MIMO-OFDM systems

KAUST Repository

Lee, Hyun Ho; Park, Kihong; Yang, Hongchuan; Ko, Youngchai

2011-01-01

-wise beamforming based on the iterative algorithm. We demonstrate that our proposed scheme can reduce the computational complexity significantly. From our simulation results, it is evident that our proposed scheme leads to a negligible performance loss compared

Compact FPGA-based beamformer using oversampled 1-bit A/D converters

DEFF Research Database (Denmark)

Tomov, Borislav Gueorguiev; Jensen, Jørgen Arendt

2005-01-01

A compact medical ultrasound beamformer architecture that uses oversampled 1-bit analog-to-digital (A/D) converters is presented. Sparse sample processing is used, as the echo signal for the image lines is reconstructed in 512 equidistant focal points along the line through its in-phase and quadr......% of the available logic resources in a commercially available midrange FPGA, and to be able to operate at 129 MHz. Simulation of the architecture at 140 MHz provides images with a dynamic range approaching 60 dB for an excitation frequency of 3 MHz.......A compact medical ultrasound beamformer architecture that uses oversampled 1-bit analog-to-digital (A/D) converters is presented. Sparse sample processing is used, as the echo signal for the image lines is reconstructed in 512 equidistant focal points along the line through its in......-phase and quadrature components. That information is sufficient for presenting a B-mode image and creating a color flow map. The high sampling rate provides the necessary delay resolution for the focusing. The low channel data width (1-bit) makes it possible to construct a compact beamformer logic. The signal...

CERN Relay Race

CERN Document Server

2006-01-01

The CERN relay race will take place around the Meyrin site on Wednesday 17 May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Details on how to register your team for the relay race are given on the Staff Association Bulletin web site.

Terahertz plasmonic Bessel beamformer

International Nuclear Information System (INIS)

Monnai, Yasuaki; Shinoda, Hiroyuki; Jahn, David; Koch, Martin; Withayachumnankul, Withawat

2015-01-01

We experimentally demonstrate terahertz Bessel beamforming based on the concept of plasmonics. The proposed planar structure is made of concentric metallic grooves with a subwavelength spacing that couple to a point source to create tightly confined surface waves or spoof surface plasmon polaritons. Concentric scatterers periodically incorporated at a wavelength scale allow for launching the surface waves into free space to define a Bessel beam. The Bessel beam defined at 0.29 THz has been characterized through terahertz time-domain spectroscopy. This approach is capable of generating Bessel beams with planar structures as opposed to bulky axicon lenses and can be readily integrated with solid-state terahertz sources

Performance Analysis of Space Information Networks with Backbone Satellite Relaying for Vehicular Networks

Directory of Open Access Journals (Sweden)

Jian Jiao

2017-01-01

Full Text Available Space Information Network (SIN with backbone satellites relaying for vehicular network (VN communications is regarded as an effective strategy to provide diverse vehicular services in a seamless, efficient, and cost-effective manner in rural areas and highways. In this paper, we investigate the performance of SIN return channel cooperative communications via an amplify-and-forward (AF backbone satellite relaying for VN communications, where we assume that both of the source-destination and relay-destination links undergo Shadowed-Rician fading and the source-relay link follows Rician fading, respectively. In this SIN-assisted VN communication scenario, we first obtain the approximate statistical distributions of the equivalent end-to-end signal-to-noise ratio (SNR of the system. Then, we derive the closed-form expressions to efficiently evaluate the average symbol error rate (ASER of the system. Furthermore, the ASER expressions are taking into account the effect of satellite perturbation of the backbone relaying satellite, which reveal the accumulated error of the antenna pointing error. Finally, simulation results are provided to verify the accuracy of our theoretical analysis and show the impact of various parameters on the system performance.

Pipeline Implementation of Polyphase PSO for Adaptive Beamforming Algorithm

Directory of Open Access Journals (Sweden)

Shaobing Huang

2017-01-01

Full Text Available Adaptive beamforming is a powerful technique for anti-interference, where searching and tracking optimal solutions are a great challenge. In this paper, a partial Particle Swarm Optimization (PSO algorithm is proposed to track the optimal solution of an adaptive beamformer due to its great global searching character. Also, due to its naturally parallel searching capabilities, a novel Field Programmable Gate Arrays (FPGA pipeline architecture using polyphase filter bank structure is designed. In order to perform computations with large dynamic range and high precision, the proposed implementation algorithm uses an efficient user-defined floating-point arithmetic. In addition, a polyphase architecture is proposed to achieve full pipeline implementation. In the case of PSO with large population, the polyphase architecture can significantly save hardware resources while achieving high performance. Finally, the simulation results are presented by cosimulation with ModelSim and SIMULINK.

SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma

2017-02-09

In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate maximization problem is intractable, we tackle a simplified problem where we maximize the sum of the harvested energy at the relays, we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relay- destination channels. The interference mitigation at the destinations is managed in two ways: either to fix the interference covariance matrices at the destination and update them at each iteration until convergence, or to cancel the interference using an algorithm similar to the BD method. We provide numerical results to show the relevance of our proposed solution.

A recurrent neural network for adaptive beamforming and array correction.

Science.gov (United States)

Che, Hangjun; Li, Chuandong; He, Xing; Huang, Tingwen

2016-08-01

In this paper, a recurrent neural network (RNN) is proposed for solving adaptive beamforming problem. In order to minimize sidelobe interference, the problem is described as a convex optimization problem based on linear array model. RNN is designed to optimize system's weight values in the feasible region which is derived from arrays' state and plane wave's information. The new algorithm is proven to be stable and converge to optimal solution in the sense of Lyapunov. So as to verify new algorithm's performance, we apply it to beamforming under array mismatch situation. Comparing with other optimization algorithms, simulations suggest that RNN has strong ability to search for exact solutions under the condition of large scale constraints. Copyright © 2016 Elsevier Ltd. All rights reserved.

Spoiled Onions: Exposing Malicious Tor Exit Relays

OpenAIRE

Winter, Philipp; Lindskog, Stefan

2014-01-01

Several hundred Tor exit relays together push more than 1 GiB/s of network traffic. However, it is easy for exit relays to snoop and tamper with anonymised network traffic and as all relays are run by independent volunteers, not all of them are innocuous. In this paper, we seek to expose malicious exit relays and document their actions. First, we monitored the Tor network after developing a fast and modular exit relay scanner. We implemented several scanning modules for detecting common attac...

Exact Performance Analysis of Dual-Hop Semi-Blind AF Relaying over Arbitrary Nakagami-m Fading Channels

KAUST Repository

Xia, Minghua

2011-10-01

Relay transmission is promising for future wireless systems due to its significant cooperative diversity gain. The performance of dual-hop semi-blind amplify-and-forward (AF) relaying systems was extensively investigated, for transmissions over Rayleigh fading channels or Nakagami- fading channels with integer fading parameter. For the general Nakagami- fading with arbitrary values, the exact closed-form system performance analysis is more challenging. In this paper, we explicitly derive the moment generation function (MGF), probability density function (PDF) and moments of the end-to-end signal-to-noise ratio (SNR) over arbitrary Nakagami- fading channels with semi-blind AF relay. With these results, the system performance evaluation in terms of outage probability, average symbol error probability, ergodic capacity and diversity order, is conducted. The analysis developed in this paper applies to any semi-blind AF relaying systems with fixed relay gain, and two major strategies for computing the relay gain are compared in terms of system performance. All analytical results are corroborated by simulation results and they are shown to be efficient tools to evaluate system performance.

Exact Performance Analysis of Dual-Hop Semi-Blind AF Relaying over Arbitrary Nakagami-m Fading Channels

KAUST Repository

Xia, Minghua; Xing, Chengwen; Wu, Yik-Chung; Aissa, Sonia

2011-01-01

Relay transmission is promising for future wireless systems due to its significant cooperative diversity gain. The performance of dual-hop semi-blind amplify-and-forward (AF) relaying systems was extensively investigated, for transmissions over Rayleigh fading channels or Nakagami-𝑚 fading channels with integer fading parameter. For the general Nakagami-𝑚 fading with arbitrary 𝑚 values, the exact closed-form system performance analysis is more challenging. In this paper, we explicitly derive the moment generation function (MGF), probability density function (PDF) and moments of the end-to-end signal-to-noise ratio (SNR) over arbitrary Nakagami-𝑚 fading channels with semi-blind AF relay. With these results, the system performance evaluation in terms of outage probability, average symbol error probability, ergodic capacity and diversity order, is conducted. The analysis developed in this paper applies to any semi-blind AF relaying systems with fixed relay gain, and two major strategies for computing the relay gain are compared in terms of system performance. All analytical results are corroborated by simulation results and they are shown to be efficient tools to evaluate system performance.

Digital Beamforming Scatterometer

Science.gov (United States)

Rincon, Rafael F.; Vega, Manuel; Kman, Luko; Buenfil, Manuel; Geist, Alessandro; Hillard, Larry; Racette, Paul

2009-01-01

This paper discusses scatterometer measurements collected with multi-mode Digital Beamforming Synthetic Aperture Radar (DBSAR) during the SMAP-VEX 2008 campaign. The 2008 SMAP Validation Experiment was conducted to address a number of specific questions related to the soil moisture retrieval algorithms. SMAP-VEX 2008 consisted on a series of aircraft-based.flights conducted on the Eastern Shore of Maryland and Delaware in the fall of 2008. Several other instruments participated in the campaign including the Passive Active L-Band System (PALS), the Marshall Airborne Polarimetric Imaging Radiometer (MAPIR), and the Global Positioning System Reflectometer (GPSR). This campaign was the first SMAP Validation Experiment. DBSAR is a multimode radar system developed at NASA/Goddard Space Flight Center that combines state-of-the-art radar technologies, on-board processing, and advances in signal processing techniques in order to enable new remote sensing capabilities applicable to Earth science and planetary applications [l]. The instrument can be configured to operate in scatterometer, Synthetic Aperture Radar (SAR), or altimeter mode. The system builds upon the L-band Imaging Scatterometer (LIS) developed as part of the RadSTAR program. The radar is a phased array system designed to fly on the NASA P3 aircraft. The instrument consists of a programmable waveform generator, eight transmit/receive (T/R) channels, a microstrip antenna, and a reconfigurable data acquisition and processor system. Each transmit channel incorporates a digital attenuator, and digital phase shifter that enables amplitude and phase modulation on transmit. The attenuators, phase shifters, and calibration switches are digitally controlled by the radar control card (RCC) on a pulse by pulse basis. The antenna is a corporate fed microstrip patch-array centered at 1.26 GHz with a 20 MHz bandwidth. Although only one feed is used with the present configuration, a provision was made for separate corporate

SWIPT in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

2017-01-01

In this paper, we consider a multiuser multiple- input multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting relays and multiple destinations. Since the end-to-end sum rate

Double-Stage Delay Multiply and Sum Beamforming Algorithm Applied to Ultrasound Medical Imaging.

Science.gov (United States)

Mozaffarzadeh, Moein; Sadeghi, Masume; Mahloojifar, Ali; Orooji, Mahdi

2018-03-01

In ultrasound (US) imaging, delay and sum (DAS) is the most common beamformer, but it leads to low-quality images. Delay multiply and sum (DMAS) was introduced to address this problem. However, the reconstructed images using DMAS still suffer from the level of side lobes and low noise suppression. Here, a novel beamforming algorithm is introduced based on expansion of the DMAS formula. We found that there is a DAS algebra inside the expansion, and we proposed use of the DMAS instead of the DAS algebra. The introduced method, namely double-stage DMAS (DS-DMAS), is evaluated numerically and experimentally. The quantitative results indicate that DS-DMAS results in an approximately 25% lower level of side lobes compared with DMAS. Moreover, the introduced method leads to 23%, 22% and 43% improvement in signal-to-noise ratio, full width at half-maximum and contrast ratio, respectively, compared with the DMAS beamformer. Copyright © 2018. Published by Elsevier Inc.

Control circuit for transformer relay

International Nuclear Information System (INIS)

Wyatt, G.A.

1984-01-01

A control circuit for a transformer relay which will automatically momentarily control the transformer relay to a selected state upon energization of the control circuit. The control circuit has an energy storage element and a current director coupled in series and adapted to be coupled with the secondary winding of the transformer relay. A device for discharge is coupled across the energy storage element. The energy storage element and current director will momentarily allow a unidirectional flow of current in the secondary winding of the transformer relay upon application of energy to the control circuit. When energy is not applied to the control circuit the device for discharge will allow the energy storage element to discharge and be available for another operation of the control circuit

Improving source discrimination performance by using an optimized acoustic array and adaptive high-resolution CLEAN-SC beamforming

NARCIS (Netherlands)

Luesutthiviboon, S.; Malgoezar, A.M.N.; Snellen, M.; Sijtsma, P.; Simons, D.G.

2018-01-01

Beamforming performance can be improved in two ways: optimizing the location of microphones on the acoustic array and applying advanced beamforming algorithms. In this study, the effects of the two approaches are studied. An optimization method is developed to optimize the location of microphones

Improper Signaling for Virtual Full-Duplex Relay Systems

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

2017-01-01

Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

Improper Signaling for Virtual Full-Duplex Relay Systems

KAUST Repository

Gaafar, Mohamed

2017-02-14

Virtual full-duplex (VFD) is a powerful solution to compensate the rate loss of half-duplex relaying without the need to full-duplex capable nodes. Inter-relay interference (IRI) challenges the operation of VFD relaying systems. Recently, improper signaling is employed at both relays of the VFD to mitigate the IRI by imposing the same signal characteristics for both relays. To further boost the achievable rate performance, asymmetric time sharing VFD relaying system is adopted with different improper signals at the half-duplex relays. The joint tuning of the three design parameters improves the achievable rate performance at different ranges of IRI and different relays locations. Extensive simulation results are presented and analyzed to show the achievable rate gain of the proposed system and understand the system behavior.

Speech-to-Speech Relay Service

Science.gov (United States)

Consumer Guide Speech to Speech Relay Service Speech-to-Speech (STS) is one form of Telecommunications Relay Service (TRS). TRS is a service that allows persons with hearing and speech disabilities ...

Active control of passive acoustic fields: passive synthetic aperture/Doppler beamforming with data from an autonomous vehicle.

Science.gov (United States)

D'Spain, Gerald L; Terrill, Eric; Chadwell, C David; Smith, Jerome A; Lynch, Stephen D

2006-12-01

The maneuverability of autonomous underwater vehicles (AUVs) equipped with hull-mounted arrays provides the opportunity to actively modify received acoustic fields to optimize extraction of information. This paper uses ocean acoustic data collected by an AUV-mounted two-dimensional hydrophone array, with overall dimension one-tenth wavelength at 200-500 Hz, to demonstrate aspects of this control through vehicle motion. Source localization is performed using Doppler shifts measured at a set of receiver velocities by both single elements and a physical array. Results show that a source in the presence of a 10-dB higher-level interferer having exactly the same frequency content (as measured by a stationary receiver) is properly localized and that white-noise-constrained adaptive beamforming applied to the physical aperture data in combination with Doppler beamforming provides greater spatial resolution than physical-aperture-alone beamforming and significantly lower sidelobes than single element Doppler beamforming. A new broadband beamformer that adjusts for variations in vehicle velocity on a sample by sample basis is demonstrated with data collected during a high-acceleration maneuver. The importance of including the cost of energy expenditure in determining optimal vehicle motion is demonstrated through simulation, further illustrating how the vehicle characteristics are an integral part of the signal/array processing structure.

Double-Stage Delay Multiply and Sum Beamforming Algorithm: Application to Linear-Array Photoacoustic Imaging

OpenAIRE

Mozaffarzadeh, Moein; Mahloojifar, Ali; Orooji, Mahdi; Adabi, Saba; Nasiriavanaki, Mohammadreza

2018-01-01

Photoacoustic imaging (PAI) is an emerging medical imaging modality capable of providing high spatial resolution of Ultrasound (US) imaging and high contrast of optical imaging. Delay-and-Sum (DAS) is the most common beamforming algorithm in PAI. However, using DAS beamformer leads to low resolution images and considerable contribution of off-axis signals. A new paradigm namely Delay-Multiply-and-Sum (DMAS), which was originally used as a reconstruction algorithm in confocal microwave imaging...

Outage performance of two-way DF relaying systems with a new relay selection metric

KAUST Repository

Hyadi, Amal

2012-04-01

This paper investigates a new constrained relay selection scheme for two-way relaying systems where two end terminals communicate simultaneously via a relay. The introduced technique is based on the maximization of the weighted sum rate of both users. To evaluate the performance of the proposed system, the outage probability is derived in a general case (where an arbitrary channel is considered), and then over independently but not necessarily identically distributed (i.n.i.d.) Rayleigh fading channels. The analytical results are verified through simulations. © 2012 IEEE.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

KAUST Repository

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2016-01-01

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Modified Dynamic Decode-and-Forward Relaying Protocol for Type II Relay in LTE-Advanced and Beyond

KAUST Repository

Nam, Sung Sik

2016-11-29

In this paper, we propose a modified dynamic decode-and-forward (MoDDF) relaying protocol to meet the critical requirements for user equipment (UE) relays in next-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed MoDDF realizes the fast jump-in relaying and the sequential decoding with an application of random codeset to encoding and re-encoding process at the source and the multiple UE relays, respectively. A subframe-by-subframe decoding based on the accumulated (or buffered) messages is employed to achieve energy, information, or mixed combining. Finally, possible early termination of decoding at the end user can lead to the higher spectral efficiency and more energy saving by reducing the frequency of redundant subframe transmission and decoding. These attractive features eliminate the need of directly exchanging control messages between multiple UE relays and the end user, which is an important prerequisite for the practical UE relay deployment. Copyright: © 2016 Nam et al. This is an open access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Improper signaling in two-path relay channels

KAUST Repository

Gaafar, Mohamed

2017-07-03

Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

Improper signaling in two-path relay channels

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Schaefer, Rafael F.; Alouini, Mohamed-Slim

2017-01-01

Inter-relay interference (IRI) challenges the operation of two-path relaying systems. Furthermore, the unavailability of the channel state information (CSI) at the source and the limited detection capabilities at the relays prevent neither eliminating the interference nor adopting joint detection at the relays nodes. Improper signaling is a powerful signaling scheme that has the capability to reduce the interference impact at the receiver side and improves the achievable rate performance. Therefore, improper signaling is adopted at both relays, which have access to the global CSI. Then, improper signal characteristics are designed to maximize the total end-to-end achievable rate at the relays. To this end, both the power and the circularity coefficient, a measure of the impropriety degree of the signal, are optimized at the relays. Although the optimization problem is not convex, optimal power allocation for both relays for a fixed circularity coefficient is obtained. Moreover, the circularity coefficient is tuned to maximize the rate for a given power allocation. Finally, a joint solution of the optimization problem is proposed using a coordinate descent method based on alternate optimization. The simulation results show that employing improper signaling improves the achievable rate at medium and high IRI.

Relay self interference minimisation using tapped filter

KAUST Repository

Jazzar, Saleh

2013-05-01

In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage and reduce the required transmitted signal power. One problem that faces relays communications is the leaked signal from the relay\\'s output to its input. This will cause an SI problem where the new received signal at the relay\\'s input will be added with the unwanted leaked signal from the relay\\'s output. A Solution is proposed in this paper to estimate and minimise this SI which is based upon using a tapped filter at the destination. To get the optimum weights for this tapped filter, some channel parameters must be estimated first. This is performed blindly at the destination without the need of any training. This channel parameter estimation method is named the blind-self-interference-channel-estimation (BSICE) method. The next step in the proposed solution is to estimate the tapped filter\\'s weights. This is performed by minimising the mean squared error (MSE) at the destination. This proposed method is named the MSE-Optimum Weight (MSE-OW) method. Simulation results are provided in this paper to verify the performance of BSICE and MSE-OW methods. © 2013 IEEE.

Dynamic Relaying in 3GPP LTE-Advanced Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Van Phan, Vinh; Redana, Simone

2009-01-01

Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while...... maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying.With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning....... Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can...

Performance limitations of relay neurons.

Directory of Open Access Journals (Sweden)

Rahul Agarwal

Full Text Available Relay cells are prevalent throughout sensory systems and receive two types of inputs: driving and modulating. The driving input contains receptive field properties that must be transmitted while the modulating input alters the specifics of transmission. For example, the visual thalamus contains relay neurons that receive driving inputs from the retina that encode a visual image, and modulating inputs from reticular activating system and layer 6 of visual cortex that control what aspects of the image will be relayed back to visual cortex for perception. What gets relayed depends on several factors such as attentional demands and a subject's goals. In this paper, we analyze a biophysical based model of a relay cell and use systems theoretic tools to construct analytic bounds on how well the cell transmits a driving input as a function of the neuron's electrophysiological properties, the modulating input, and the driving signal parameters. We assume that the modulating input belongs to a class of sinusoidal signals and that the driving input is an irregular train of pulses with inter-pulse intervals obeying an exponential distribution. Our analysis applies to any [Formula: see text] order model as long as the neuron does not spike without a driving input pulse and exhibits a refractory period. Our bounds on relay reliability contain performance obtained through simulation of a second and third order model, and suggest, for instance, that if the frequency of the modulating input increases or the DC offset decreases, then relay increases. Our analysis also shows, for the first time, how the biophysical properties of the neuron (e.g. ion channel dynamics define the oscillatory patterns needed in the modulating input for appropriately timed relay of sensory information. In our discussion, we describe how our bounds predict experimentally observed neural activity in the basal ganglia in (i health, (ii in Parkinson's disease (PD, and (iii in PD during

Modular relay control

OpenAIRE

Ivarsson, Mikael

2010-01-01

Enics Sweden AB, Västerås, is an electronics manufacturing services company with its main business in manufacturing electronics. Most, if not all, electronic devices that are manufactured are being widely tested before delivery to ensure proper functionality. Often during tests a large number of signals are measured by one to a few digital multimeters and are therefore controlled through relays. Relays are also used when applying stimuli with high currents or voltages to the unit under test. ...

Computational Acoustic Beamforming for Noise Source Identification for Small Wind Turbines.

Science.gov (United States)

Ma, Ping; Lien, Fue-Sang; Yee, Eugene

2017-01-01

This paper develops a computational acoustic beamforming (CAB) methodology for identification of sources of small wind turbine noise. This methodology is validated using the case of the NACA 0012 airfoil trailing edge noise. For this validation case, the predicted acoustic maps were in excellent conformance with the results of the measurements obtained from the acoustic beamforming experiment. Following this validation study, the CAB methodology was applied to the identification of noise sources generated by a commercial small wind turbine. The simulated acoustic maps revealed that the blade tower interaction and the wind turbine nacelle were the two primary mechanisms for sound generation for this small wind turbine at frequencies between 100 and 630 Hz.

Ein Beitrag zur Erweiterung von Beamforming-Methoden

OpenAIRE

Kern, Marcus

2008-01-01

Im automobilen Entwicklungsprozess haben sich akustische Messsysteme etabliert, die mit einer Anordnung von Mikrofonen, einer optischen Kamera und einer nachgeschalteten Signalverarbeitung die Schalleinfallsrichtung detektieren und dadurch die Schalldruckverteilung auf Quellorte im Fernfeld zurückrechnen und visualisieren können. Die Signalverarbeitung beruht i. A. auf dem Delay&Sum-Beamforming, deren Umsetzung im Zeit- oder Frequenzbereich erfolgt. Die Schwächen dieser Messtechnik bezüglich ...

On the achievable degrees of freedom of alternate MIMO relaying with multiple AF relays

KAUST Repository

Park, Kihong; Alouini, Mohamed-Slim; Park, Seongho; Ko, Youngchai

2012-01-01

In this paper, we consider a two-hop relaying network where one source, one destination, and multiple amplify-and-forward (AF) relays equipped with M antennas operate in a half-duplex mode. In order to compensate for the inherent loss of capacity

Eigenspace-Based Minimum Variance Adaptive Beamformer Combined with Delay Multiply and Sum: Experimental Study

OpenAIRE

Mozaffarzadeh, Moein; Mahloojifar, Ali; Nasiriavanaki, Mohammadreza; Orooji, Mahdi

2017-01-01

Delay and sum (DAS) is the most common beamforming algorithm in linear-array photoacoustic imaging (PAI) as a result of its simple implementation. However, it leads to a low resolution and high sidelobes. Delay multiply and sum (DMAS) was used to address the incapabilities of DAS, providing a higher image quality. However, the resolution improvement is not well enough compared to eigenspace-based minimum variance (EIBMV). In this paper, the EIBMV beamformer has been combined with DMAS algebra...

Beamspace Adaptive Beamforming for Hydrodynamic Towed Array Self-Noise Cancellation

National Research Council Canada - National Science Library

Premus, Vincent

2001-01-01

... against signal self-nulling associated with steering vector mismatch. Particular attention is paid to the definition of white noise gain as the metric that reflects the level of mainlobe adaptive nulling for an adaptive beamformer...

Beamspace Adaptive Beamforming for Hydrodynamic Towed Array Self-Noise Cancellation

National Research Council Canada - National Science Library

Premus, Vincent

2000-01-01

... against signal self-nulling associated with steering vector mismatch. Particular attention is paid to the definition of white noise gain as the metric that reflects the level of mainlobe adaptive nulling for an adaptive beamformer...

Experimental performance assessment of the sub-band minimum variance beamformer for ultrasound imaging

DEFF Research Database (Denmark)

Diamantis, Konstantinos; Greenaway, Alan H.; Anderson, Tom

2017-01-01

Recent progress in adaptive beamforming techniques for medical ultrasound has shown that current resolution limits can be surpassed. One method of obtaining improved lateral resolution is the Minimum Variance (MV) beamformer. The frequency domain implementation of this method effectively divides...... the broadband ultrasound signals into sub-bands (MVS) to conform with the narrow-band assumption of the original MV theory. This approach is investigated here using experimental Synthetic Aperture (SA) data from wire and cyst phantoms. A 7 MHz linear array transducer is used with the SARUS experimental...

Iterative Relay Scheduling with Hybrid ARQ under Multiple User Equipment (Type II) Relay Environments

KAUST Repository

Nam, Sung Sik; Alouini, Mohamed-Slim; Choi, Seyeong

2018-01-01

-generation cellular systems (e.g., LTE-Advanced and beyond). The proposed IRS-HARQ aims to increase the achievable data rate by iteratively scheduling a relatively better UE relay closer to the end user in a probabilistic sense, provided that the relay-to-end user

Multiple relay selection for delay-limited applications

KAUST Repository

Alsharoa, Ahmad M.

2013-12-01

A multiple relay selection system model that implements the decode-and-forward mode is investigated. All communication nodes are assumed to be equipped by multiple antennas. Furthermore, lattices space-time coded multiple-input multiple-output half duplex channel is applied. The main goal is to increase the throughput of the system by selecting multiple number of relays. The selection criteria depends on the maximum decoding delay at relays where the system implements a decoding time-out algorithm at each relay. This leads to a significant saving in the overall system power consumptions and attempts to solve the relays synchronization problem. All results are presented using numerical simulations. © 2012 IEEE.

Dynamic Relaying in 3GPP LTE-Advanced Networks

Directory of Open Access Journals (Sweden)

Van Phan Vinh

2009-01-01

Full Text Available Relaying is one of the proposed technologies for LTE-Advanced networks. In order to enable a flexible and reliable relaying support, the currently adopted architectural structure of LTE networks has to be modified. In this paper, we extend the LTE architecture to enable dynamic relaying, while maintaining backward compatibility with LTE Release 8 user equipments, and without limiting the flexibility and reliability expected from relaying. With dynamic relaying, relays can be associated with base stations on a need basis rather than in a fixed manner which is based only on initial radio planning. Proposals are also given on how to further improve a relay enhanced LTE network by enabling multiple interfaces between the relay nodes and their controlling base stations, which can possibly be based on technologies different from LTE, so that load balancing can be realized. This load balancing can be either between different base stations or even between different networks.

Airborne relay-based regional positioning system.

Science.gov (United States)

Lee, Kyuman; Noh, Hongjun; Lim, Jaesung

2015-05-28

Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations.

Improving beamforming by optimization of acoustic array microphone positions

NARCIS (Netherlands)

Malgoezar, A.M.N.; Snellen, M.; Sijtsma, P.; Simons, D.G.

2016-01-01

Assigning proper positions to microphones within arrays is essential in order to reduce or eliminate side- and grating lobes in 2D beamform images. In this paper an objective function is derived providing a measure for the presence of artificial sources. Using the global optimization method

Hardware dependencies of GPU-accelerated beamformer performances for microwave breast cancer detection

Directory of Open Access Journals (Sweden)

Salomon Christoph J.

2016-09-01

Full Text Available UWB microwave imaging has proven to be a promising technique for early-stage breast cancer detection. The extensive image reconstruction time can be accelerated by parallelizing the execution of the underlying beamforming algorithms. However, the efficiency of the parallelization will most likely depend on the grade of parallelism of the imaging algorithm and of the utilized hardware. This paper investigates the dependencies of two different beamforming algorithms on multiple hardware specification of several graphics boards. The parallel implementation is realized by using NVIDIA’s CUDA. Three conclusions are drawn about the behavior of the parallel implementation and how to efficiently use the accessible hardware.

Bilayer expurgated LDPC codes with uncoded relaying

Directory of Open Access Journals (Sweden)

Md. Noor-A-Rahim

2017-08-01

Full Text Available Bilayer low-density parity-check (LDPC codes are an effective coding technique for decode-and-forward relaying, where the relay forwards extra parity bits to help the destination to decode the source bits correctly. In the existing bilayer coding scheme, these parity bits are protected by an error correcting code and assumed reliably available at the receiver. We propose an uncoded relaying scheme, where the extra parity bits are forwarded to the destination without any protection. Through density evolution analysis and simulation results, we show that our proposed scheme achieves better performance in terms of bit erasure probability than the existing relaying scheme. In addition, our proposed scheme results in lower complexity at the relay.

A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

KAUST Repository

Rao, Anlei

2015-09-11

Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (QoS) requirements. For the later type design, previous works has worked on minimizing the approximated power consumption. In this paper, exact power consumption for all relays is derived into a quadratic form by diagonalizing the minimum-square error (MSE) matrix, and the relay precoding matrix is designed by optimizing this quadratic form with the help of semidefinite programming (SDP) relaxation. Our simulation results show that such a design can achieve a gain of around 3 dB against the previous design, which optimized the approximated power consumption. © 2015 IEEE.

Performance analysis of underlay cognitive multihop regenerative relaying systems with multiple primary receivers

KAUST Repository

Hyadi, Amal; Benjillali, Mustapha; Alouini, Mohamed-Slim; Da Costa, Daniel Benevides Da

2013-01-01

Multihop relaying is an efficient strategy to improve the connectivity and extend the coverage area of secondary networks in underlay cognitive systems. In this work, we provide a comprehensive performance study of cognitive multihop regenerative

Opportunistic Relay Selection with Cooperative Macro Diversity

Directory of Open Access Journals (Sweden)

Yu Chia-Hao

2010-01-01

Full Text Available We apply a fully opportunistic relay selection scheme to study cooperative diversity in a semianalytical manner. In our framework, idle Mobile Stations (MSs are capable of being used as Relay Stations (RSs and no relaying is required if the direct path is strong. Our relay selection scheme is fully selection based: either the direct path or one of the relaying paths is selected. Macro diversity, which is often ignored in analytical works, is taken into account together with micro diversity by using a complete channel model that includes both shadow fading and fast fading effects. The stochastic geometry of the network is taken into account by having a random number of randomly located MSs. The outage probability analysis of the selection differs from the case where only fast fading is considered. Under our framework, distribution of the received power is formulated using different Channel State Information (CSI assumptions to simulate both optimistic and practical environments. The results show that the relay selection gain can be significant given a suitable amount of candidate RSs. Also, while relay selection according to incomplete CSI is diversity suboptimal compared to relay selection based on full CSI, the loss in average throughput is not too significant. This is a consequence of the dominance of geometry over fast fading.

Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

KAUST Repository

Khan, Fahd Ahmed; Tourki, Kamel; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2015-01-01

In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

Opportunistic Fixed Gain Bidirectional Relaying with Outdated CSI

KAUST Repository

Khan, Fahd Ahmed

2015-05-01

In a network with multiple relays, relay selection has been shown as an effective scheme to achieve diversity as well as to improve the overall throughput. This paper studies the impact of using outdated channel state information for relay selection on the performance of a network where two sources communicate with each other via fixed-gain amplify-and-forward relays. For a Rayleigh faded channel, closed-form expressions for the outage probability, moment generating function and symbol error rate are derived. Simulations results are also presented to corroborate the derived analytical results. It is shown that adding relays does not improve the performance if the channel is substantially outdated. Furthermore, relay location is also taken into consideration and it is shown that the performance can be improved by placing the relay closer to the source whose channel is more outdated. © 2015 IEEE.

MaROS Strategic Relay Planning and Coordination Interfaces

Science.gov (United States)

Allard, Daniel A.

2010-01-01

The Mars Relay Operations Service (MaROS) is designed to provide planning and analysis tools in support of ongoing Mars Network relay operations. Strategic relay planning requires coordination between lander and orbiter mission ground data system (GDS) teams to schedule and execute relay communications passes. MaROS centralizes this process, correlating all data relevant to relay coordination to provide a cohesive picture of the relay state. Service users interact with the system through thin-layer command line and web user interface client applications. Users provide and utilize data such as lander view periods of orbiters, Deep Space Network (DSN) antenna tracks, and reports of relay pass performance. Users upload and download relevant relay data via formally defined and documented file structures including some described in Extensible Markup Language (XML). Clients interface with the system via an http-based Representational State Transfer (ReST) pattern using Javascript Object Notation (JSON) formats. This paper will provide a general overview of the service architecture and detail the software interfaces and considerations for interface design.

CERN Relay Race 2009

CERN Document Server

2009-01-01

The CERN relay race will take place around the Meyrin site on Thursday 14th May starting at 12:15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. More details on how to register your team for the relay race

Reversal thyristor-relay direct current commutator

International Nuclear Information System (INIS)

Ivanenko, A.I.

1982-01-01

A thyristor-relay commutator used for alteration of the leading magnetic field direction in experiments with polarized neutrons is described. The commutator flowsheet is presented. Thyristors, connected so as to allow the relay trigger operation mode, are used as controllable electronic relay. Two connected in series coils with the total inductance of the order of 0.28 H serve as the electronic relay load. The arc-free current commutation is effected at the moment of the minimal current across the load terminals, which allows to easily reverse the current up to 10 A at a volatage, v <= 150 V. The experience gained within a year of operation has shown that the commutator meets the requirements of reliability and tuning

CERN Relay Race

CERN Multimedia

2011-01-01

The CERN relay race will take place around the Meyrin site on Thursday 19 May starting at 12-15. If possible, please avoid driving on the site during this 20-minute period. If you do meet runners while driving your car, please STOP until they have all passed. Thank you for your cooperation. Details of the course and of how to register your team for the relay race can be found here. Some advice for all runners from the Medical Service can also be found here.   

A low complexity algorithm for multiple relay selection in two-way relaying Cognitive Radio networks

KAUST Repository

Alsharoa, Ahmad M.

2013-06-01

In this paper, a multiple relay selection scheme for two-way relaying cognitive radio network is investigated. We consider a cooperative Cognitive Radio (CR) system with spectrum sharing scenario using Amplify-and-Forward (AF) protocol, where licensed users and unlicensed users operate on the same frequency band. The main objective is to maximize the sum rate of the unlicensed users allowed to share the spectrum with the licensed users by respecting a tolerated interference threshold. A practical low complexity heuristic approach is proposed to solve our formulated optimization problem. Selected numerical results show that the proposed algorithm reaches a performance close to the performance of the optimal multiple relay selection scheme either with discrete or continuous power distributions while providing a considerable saving in terms of computational complexity. In addition, these results show that our proposed scheme significantly outperforms the single relay selection scheme. © 2013 IEEE.

Analysis of errors of radiation relay, (1)

International Nuclear Information System (INIS)

Koyanagi, Takami; Nakajima, Sinichi

1976-01-01

The statistical error of liquid level controlled by radiation relay is analysed and a method of minimizing the error is proposed. This method comes to the problem of optimum setting of the time constant of radiation relay. The equations for obtaining the value of time constant are presented and the numerical results are shown in a table and plotted in a figure. The optimum time constant of the upper level control relay is entirely different from that of the lower level control relay. (auth.)

TX-RX isolation method based on polarization diversity, spatial diversity and TX beamforming

DEFF Research Database (Denmark)

Foroozanfard, Ehsan; Carvalho, Elisabeth De; Pedersen, Gert F.

2016-01-01

In this paper, the feasibility of an antenna isolation technique based on null-steer beamforming, polarization diversity and spatial diversity is investigated. The proposed system consists of six patch antennas which are fed by a feeding network to obtain a null-steer beamformer. To achieve spatial...... diversity, antenna elements are located on two layers, facing in a different direction. Moreover, the antenna elements in two layers use different polarization. The measured results of the antenna system present a high TX-RX isolation in the order of 70 dB which shows the feasibility of such a system...

Relay tracking control for second-order multi-agent systems with damaged agents.

Science.gov (United States)

Dong, Lijing; Li, Jing; Liu, Qin

2017-11-01

This paper investigates a situation where smart agents capable of sensory and mobility are deployed to monitor a designated area. A preset number of agents start tracking when a target intrudes this area. Some of the tracking agents are possible to be out of order over the tracking course. Thus, we propose a cooperative relay tracking strategy to ensure the successful tracking with existence of damaged agents. Relay means that, when a tracking agent quits tracking due to malfunction, one of the near deployed agents replaces it to continue the tracking task. This results in jump of tracking errors and dynamic switching of topology of the multi-agent system. Switched system technique is employed to solve this specific problem. Finally, the effectiveness of proposed tracking strategy and validity of the theoretical results are verified by conducting a numerical simulation. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

49 CFR 236.52 - Relayed cut-section.

Science.gov (United States)

2010-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Rules and Instructions: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...

Quantum cryptography with an ideal local relay

DEFF Research Database (Denmark)

Spedalieri, Gaetana; Ottaviani, Carlo; Braunstein, Samuel L.

2015-01-01

We consider two remote parties connected to a relay by two quantum channels. To generate a secret key, they transmit coherent states to the relay, where the states are subject to a continuous-variable (CV) Bell detection. We study the ideal case where Alice's channel is lossless, i.e., the relay ...

A SDP based design of relay precoding for the power minimization of MIMO AF-relay networks

KAUST Repository

Rao, Anlei; Park, Kihong; Alouini, Mohamed-Slim

2015-01-01

Relay precoding for multiple-input and multiple-output (MIMO) relay networks has been approached by either optimizing the efficiency performance with given power consumption constraints or minimizing the power consumption with quality-of-service (Qo

User Multiplexing in Relay Enhanced LTE-Advanced Networks

DEFF Research Database (Denmark)

Teyeb, Oumer Mohammed; Frederiksen, Frank; Redana, Simone

2010-01-01

is radio relaying. This uses relay nodes that act as surrogate base stations for mobile users whose radio links with the base stations are not experiencing good enough conditions. In the downlink, the data that is destined for the relayed users may first have to be multiplexed by the base station, sent...... over the wireless backhaul link towards the relay node, and de-multiplexed and forwarded to the individual users by the relay node. The reverse process also has to be undertaken in the uplink. In this paper, we present a novel multiplexing scheme which is able to adapt the addressing and bitmapping...... of user identification to the actual number of users being served by the relay nodes, and thus greatly reduce the multiplexing overhead....

Amplify-and-forward relaying in wireless communications

CERN Document Server

Rodriguez, Leonardo Jimenez; Le-Ngoc, Tho

2015-01-01

This SpringerBrief explores the advantage of relaying techniques in addressing the increasing demand for high data rates and reliable services over the air. It demonstrates how to design cost-effective relay systems that provide high spectral efficiency and fully exploit the diversity of the relay channel. The brief covers advances in achievable rates, power allocation schemes, and error performance for half-duplex (HD) and full-duplex (FD) amplify-and-forward (AF) single-relay systems. The authors discuss the capacity and respective optimal power allocation for a wide range of HD protocols ov

Digital Beamforming Synthetic Aperture Radar Developments at NASA Goddard Space Flight Center

Science.gov (United States)

Rincon, Rafael; Fatoyinbo, Temilola; Osmanoglu, Batuhan; Lee, Seung Kuk; Du Toit, Cornelis F.; Perrine, Martin; Ranson, K. Jon; Sun, Guoqing; Deshpande, Manohar; Beck, Jaclyn;

Full-Duplex Relay Selection in Cognitive Underlay Networks

KAUST Repository

Khafagy, Mohammad Galal

2017-09-30

In this work, we analyze the performance of full-duplex relay selection (FDRS) in spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay(s), thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint, which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic FDRS with residual self-interference (RSI) by deriving the exact cumulative distribution function of its end-to-end signal-to-interference-plus-noise ratio under Nakagami-m fading. We also evaluate the offered diversity gain of relay selection for different full-duplex cooperation schemes in the presence/absence of a direct source-destination link. When the adopted RSI link gain model is sublinear in the relay power, which agrees with recent research findings, we show that remarkable diversity gain can be recovered even in the presence of an interfering direct link. Second, we evaluate the end-to-end performance of FDRS with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

On Alternate Relaying with Improper Gaussian Signaling

KAUST Repository

Gaafar, Mohamed; Amin, Osama; Ikhlef, Aissa; Chaaban, Anas; Alouini, Mohamed-Slim

2016-01-01

In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

On Alternate Relaying with Improper Gaussian Signaling

KAUST Repository

Gaafar, Mohamed

2016-06-06

In this letter, we investigate the potential benefits of adopting improper Gaussian signaling (IGS) in a two-hop alternate relaying (AR) system. Given the known benefits of using IGS in interference-limited networks, we propose to use IGS to relieve the inter-relay interference (IRI) impact on the AR system assuming no channel state information is available at the source. In this regard, we assume that the two relays use IGS and the source uses proper Gaussian signaling (PGS). Then, we optimize the degree of impropriety of the relays signal, measured by the circularity coefficient, to maximize the total achievable rate. Simulation results show that using IGS yields a significant performance improvement over PGS, especially when the first hop is a bottleneck due to weak source-relay channel gains and/or strong IRI.

An Optimal Beamforming Algorithm for Phased-Array Antennas Used in Multi-Beam Spaceborne Radiometers

DEFF Research Database (Denmark)

Iupikov, O. A.; Ivashina, M. V.; Pontoppidan, K.

2015-01-01

Strict requirements for future spaceborne ocean missions using multi-beam radiometers call for new antenna technologies, such as digital beamforming phased arrays. In this paper, we present an optimal beamforming algorithm for phased-array antenna systems designed to operate as focal plane arrays...... to a FPA feeding a torus reflector antenna (designed under the contract with the European Space Agency) and tested for multiple beams. The results demonstrate an improved performance in terms of the optimized beam characteristics, yielding much higher spatial and radiometric resolution as well as much...

An assessment of fire vulnerability for aged electrical relays

International Nuclear Information System (INIS)

Vigil, R.A.; Nowlen, S.P.

1995-03-01

There has been some concern that, as nuclear power plants age, protective measures taken to control and minimize the impact of fire may become ineffective, or significantly less effective, and hence result in an increased fire risk. One objective of the Fire Vulnerability of Aged Electrical Components Program is to assess the effects of aging and service wear on the fire vulnerability of electrical equipment. An increased fire vulnerability of components may lead to an overall increase in fire risk to the plant. Because of their widespread use in various electrical safety systems, electromechanical relays were chosen to be the initial components for evaluation. This test program assessed the impact of operational and thermal aging on the vulnerability of these relays to fire-induced damage. Only thermal effects of a fire were examined in this test program. The impact of smoke, corrosive materials, or fire suppression effects on relay performance were not addressed in this test program. The purpose of this test program was to assess whether the fire vulnerability of electrical relays increased with aging. The sequence followed for the test program was to: identify specific relay types, develop three fire scenarios, artificially age several relays, test the unaged and aged relays in the fire exposure scenarios, and compare the results. The relays tested were Agastat GPI, General Electric (GE) HMA, HGA, and HFA. At least two relays of each type were artificially aged and at least two relays of each type were new. Relays were operationally aged by cycling the relay under rated load for 2,000 operations. These relays were then thermally aged for 60 days with their coil energized

Microprocessor protection relays: new prospects or new problems?

OpenAIRE

Gurevich, Vladimir

2006-01-01

The internal architecture and principles of operation of microprocessor-based devices including so-called "microprocessor protective relays" have little in common with devices called "electric relays". But microprocessor-based relay protection devices are gradually driving out the traditional electromechanical and even electronic relay protection of virtually from all fields of power and electrical engineering. Advantages of microprocessor-based protection means over traditional ones are far ...

Multiple and single snapshot compressive beamforming

DEFF Research Database (Denmark)

Gerstoft, Peter; Xenaki, Angeliki; Mecklenbrauker, Christoph F.

2015-01-01

and multiple snapshots. CS does not require inversion of the data covariance matrix and thus works well even for a single snapshot where it gives higher resolution than conventional beamforming. For multiple snapshots, CS outperforms conventional high-resolution methods even with coherent arrivals and at low......-lagged superposition of source amplitudes at all hypothetical DOAs. Regularizing with an ‘1-norm constraint renders the problem solvable with convex optimization, and promoting sparsity gives highresolution DOA maps. Here the sparse source distribution is derived using maximum a posteriori estimates for both single...

Cognitive Relay Networks: A Comprehensive Survey

Directory of Open Access Journals (Sweden)

Ayesha Naeem

2015-07-01

Full Text Available Cognitive radio is an emerging technology to deal with the scarcity and requirement of radio spectrum by dynamically assigning spectrum to unlicensed user . This revolutionary technology shifts the paradigm in the wireless system design by all owing unlicensed user the ability to sense, adapt and share the dynamic spectrum. Cognitive radio technology have been applied to different networks and applications ranging from wireless to public saf ety, smart grid, medical, rela y and cellular applications to increase the throughput and spectrum efficiency of the network. Among these applications, cognitive relay networks is one of the application where cognitive radio technology has been applied. Cognitiv e rela y network increases the network throughput by reducing the complete pa th loss and also by ensuring cooper ation among secondary users and cooperation among primary and secondary users. In this paper , our aim is to provide a survey on cognitive relay network. We also provide a detailed review on existing schemes in cognitive relay networks on the basis of relaying protocol, relay cooperation and channel model.

Compressive Sound Speed Profile Inversion Using Beamforming Results

Directory of Open Access Journals (Sweden)

Youngmin Choo

2018-05-01

Full Text Available Sound speed profile (SSP significantly affects acoustic propagation in the ocean. In this work, the SSP is inverted using compressive sensing (CS combined with beamforming to indicate the direction of arrivals (DOAs. The travel times and the positions of the arrivals can be approximately linearized using their Taylor expansion with the shape function coefficients that parameterize the SSP. The linear relation between the travel times/positions and the shape function coefficients enables CS to reconstruct the SSP. The conventional objective function in CS is modified to simultaneously exploit the information from the travel times and positions. The SSP is estimated using CS with beamforming of ray arrivals in the SWellEx-96 experimental environment, and the performance is evaluated using the correlation coefficient and mean squared error (MSE between the true and recovered SSPs, respectively. Five hundred synthetic SSPs were generated by randomly choosing the SSP dictionary components, and more than 80 percent of all the cases have correlation coefficients over 0.7 and MSE along depth is insignificant except near the sea surface, which shows the validity of the proposed method.

Error-rate performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can

Oscillatory neuronal dynamics associated with manual acupuncture: a magnetoencephalography study using beamforming analysis

Directory of Open Access Journals (Sweden)

Aziz eAsghar

2012-11-01

Full Text Available Magnetoencephalography (MEG enables non-invasive recording of neuronal activity, with reconstruction methods providing estimates of underlying brain source locations and oscillatory dynamics from externally recorded neuromagnetic fields. The aim of our study was to use MEG to determine the effect of manual acupuncture on neuronal oscillatory dynamics. A major problem in MEG investigations of manual acupuncture is the absence of onset times for each needle manipulation. Given that beamforming (spatial filtering analysis is not dependent upon stimulus-driven responses being phase-locked to stimulus onset, we postulated that beamforming could reveal source locations and induced changes in neuronal activity during manual acupuncture. In a beamformer analysis, a two-minute period of manual acupuncture needle manipulation delivered to the ipsilateral right LI-4 (Hegu acupoint was contrasted with a two-minute baseline period. We considered oscillatory power changes in the theta (4-8Hz, alpha (8-13Hz, beta (13-30Hz and gamma (30-100Hz frequency bands. We found significant decreases in beta band power in the contralateral primary somatosensory cortex and superior frontal gyrus. In the ipsilateral cerebral hemisphere, we found significant power decreases in beta and gamma frequency bands in only the superior frontal gyrus. No significant power modulations were found in theta and alpha bands. Our results indicate that beamforming is a useful analytical tool to reconstruct underlying neuronal activity associated with manual acupuncture. Our main finding was of beta power decreases in primary somatosensory cortex and superior frontal gyrus, which opens up a line of future investigation regarding whether this contributes towards an underlying mechanism of acupuncture.

Experimental evaluation of earthquake induced relay chattering

International Nuclear Information System (INIS)

Bandyopadhyay, K.; Hofmayer, C.; Shteyngart, S.

1990-01-01

An experimental evaluation of relay performance under vibratory environments is discussed in this paper. Single frequency excitation was used for most tests. Limited tests were performed with random multifrequency inputs. The capacity of each relay was established based on a two-millisecond chatter criterion. The experimental techniques are described and the effects of parameters in controlling the relay capacity levels are illustrated with test data. A wide variation of the capacity levels was observed due to the influence of parameters related to the design of the relay and nature of the input motion. 3 refs., 15 figs

On the input distribution and optimal beamforming for the MISO VLC wiretap channel

KAUST Repository

Arfaoui, Mohamed Amine; Rezki, Zouheir; Ghrayeb, Ali; Alouini, Mohamed-Slim

2017-01-01

We investigate in this paper the achievable secrecy rate of the multiple-input single-output (MISO) visible light communication (VLC) Gaussian wiretap channel with single user and single eavesdropper. We consider the cases when the location of eavesdropper is known or unknown to the transmitter. In the former case, we derive the optimal beamforming in closed form, subject to constrained inputs. In the latter case, we apply robust beamforming. Furthermore, we study the achievable secrecy rate when the input follows the truncated generalized normal (TGN) distribution. We present several examples which demonstrate the substantial improvements in the secrecy rates achieved by the proposed techniques.

On the input distribution and optimal beamforming for the MISO VLC wiretap channel

KAUST Repository

Arfaoui, Mohamed Amine

2017-05-12

We investigate in this paper the achievable secrecy rate of the multiple-input single-output (MISO) visible light communication (VLC) Gaussian wiretap channel with single user and single eavesdropper. We consider the cases when the location of eavesdropper is known or unknown to the transmitter. In the former case, we derive the optimal beamforming in closed form, subject to constrained inputs. In the latter case, we apply robust beamforming. Furthermore, we study the achievable secrecy rate when the input follows the truncated generalized normal (TGN) distribution. We present several examples which demonstrate the substantial improvements in the secrecy rates achieved by the proposed techniques.

Relay protection features of frequency-adjustable electric drive

Science.gov (United States)

Kuprienko, V. V.

2018-03-01

The features of relay protection of high-voltage electric motors in composition of the frequency-adjustable electric drive are considered in the article. The influence of frequency converters on the stability of the operation of various types of relay protection used on electric motors is noted. Variants of circuits for connecting relay protection devices are suggested. The need to develop special relay protection devices for a frequency-adjustable electric drive is substantiated.

Cobalt: A GPU-based correlator and beamformer for LOFAR

Science.gov (United States)

Broekema, P. Chris; Mol, J. Jan David; Nijboer, R.; van Amesfoort, A. S.; Brentjens, M. A.; Loose, G. Marcel; Klijn, W. F. A.; Romein, J. W.

2018-04-01

For low-frequency radio astronomy, software correlation and beamforming on general purpose hardware is a viable alternative to custom designed hardware. LOFAR, a new-generation radio telescope centered in the Netherlands with international stations in Germany, France, Ireland, Poland, Sweden and the UK, has successfully used software real-time processors based on IBM Blue Gene technology since 2004. Since then, developments in technology have allowed us to build a system based on commercial off-the-shelf components that combines the same capabilities with lower operational cost. In this paper, we describe the design and implementation of a GPU-based correlator and beamformer with the same capabilities as the Blue Gene based systems. We focus on the design approach taken, and show the challenges faced in selecting an appropriate system. The design, implementation and verification of the software system show the value of a modern test-driven development approach. Operational experience, based on three years of operations, demonstrates that a general purpose system is a good alternative to the previous supercomputer-based system or custom-designed hardware.

Relay Telecommunications for the Coming Decade of Mars Exploration

Science.gov (United States)

Edwards, C.; DePaula, R.

2010-01-01

Over the past decade, an evolving network of relay-equipped orbiters has advanced our capabilities for Mars exploration. NASA's Mars Global Surveyor, 2001 Mars Odyssey, and Mars Reconnaissance Orbiter (MRO), as well as ESA's Mars Express Orbiter, have provided telecommunications relay services to the 2003 Mars Exploration Rovers, Spirit and Opportunity, and to the 2007 Phoenix Lander. Based on these successes, a roadmap for continued Mars relay services is in place for the coming decade. MRO and Odyssey will provide key relay support to the 2011 Mars Science Laboratory (MSL) mission, including capture of critical event telemetry during entry, descent, and landing, as well as support for command and telemetry during surface operations, utilizing new capabilities of the Electra relay payload on MRO and the Electra-Lite payload on MSL to allow significant increase in data return relative to earlier missions. Over the remainder of the decade a number of additional orbiter and lander missions are planned, representing new orbital relay service providers and new landed relay users. In this paper we will outline this Mars relay roadmap, quantifying relay performance over time, illustrating planned support scenarios, and identifying key challenges and technology infusion opportunities.

Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma

2016-09-20

In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

Sum-Rate Enhancement in Multiuser MIMO Decode-and-Forward Relay Broadcasting Channel with Energy Harvesting Relays

KAUST Repository

Benkhelifa, Fatma; Salem, Ahmed Sultan; Alouini, Mohamed-Slim

2016-01-01

In this paper, we consider a multiuser multipleinput multiple-output (MIMO) decode-and-forward (DF) relay broadcasting channel (BC) with single source, multiple energy harvesting (EH) relays and multiple destinations. All the nodes are equipped with multiple antennas. The EH and information decoding (ID) tasks at the relays and destinations are separated over the time, which is termed as the time switching (TS) scheme. As optimal solutions for the sum-rate maximization problems of BC channels and the MIMO interference channels are hard to obtain, the end-to-end sum rate maximization problem of a multiuser MIMO DF relay BC channel is even harder. In this paper, we propose to tackle a simplified problem where we employ the block diagonalization (BD) procedure at the source, and we mitigate the interference between the relaydestination channels using an algorithm similar to the BD method. In order to show the relevance of our low complex proposed solution, we compare it to the minimum mean-square error (MMSE) solution that was shown in the literature to be equivalent to the solution of the sum-rate maximization in MIMO broadcasting interfering channels. We also investigate the time division multiple access (TDMA) solution which separates all the information transmissions from the source to the relays and from the relays to the destinations over time. We provide numerical results to show the relevance of our proposed solution, in comparison with the no co-channel interference (CCI) case, the TDMA based solution and the MMSE based solution.

Evaluation of Harmonics Impact on Digital Relays

Directory of Open Access Journals (Sweden)

Kinan Wannous

2018-04-01

Full Text Available This paper presents the concept of the impact of harmonic distortion on a digital protection relay. The aim is to verify and determine the reasons of a mal-trip or failure to trip the protection relays; the suggested solution of the harmonic distortion is explained by a mathematical model in the Matlab Simulink programming environment. The digital relays have been tested under harmonic distortions in order to verify the function of the relays algorithm under abnormal conditions. The comparison between the protection relay algorithm under abnormal conditions and a mathematical model in the Matlab Simulink programming environment based on injected harmonics of high values is provided. The test is separated into different levels; the first level is based on the harmonic effect of an individual harmonic and mixed harmonics. The test includes the effect of the harmonics in the location of the fault point into distance protection zones. This paper is a new proposal in the signal processing of power quality disturbances using Matlab Simulink and the power quality impact on the measurements of the power system quantities; the test simulates the function of protection in power systems in terms of calculating the current and voltage values of short circuits and their faults. The paper includes several tests: frequency variations and decomposition of voltage waveforms with Fourier transforms (model and commercial relay, the effect of the power factor on the location of fault points, the relation between the tripping time and the total harmonic distortion (THD levels in a commercial relay, and a comparison of the THD capture between the commercial relay and the model.

Millimetre Level Accuracy GNSS Positioning with the Blind Adaptive Beamforming Method in Interference Environments

Directory of Open Access Journals (Sweden)

Saeed Daneshmand

2016-10-01

Full Text Available The use of antenna arrays in Global Navigation Satellite System (GNSS applications is gaining significant attention due to its superior capability to suppress both narrowband and wideband interference. However, the phase distortions resulting from array processing may limit the applicability of these methods for high precision applications using carrier phase based positioning techniques. This paper studies the phase distortions occurring with the adaptive blind beamforming method in which satellite angle of arrival (AoA information is not employed in the optimization problem. To cater to non-stationary interference scenarios, the array weights of the adaptive beamformer are continuously updated. The effects of these continuous updates on the tracking parameters of a GNSS receiver are analyzed. The second part of this paper focuses on reducing the phase distortions during the blind beamforming process in order to allow the receiver to perform carrier phase based positioning by applying a constraint on the structure of the array configuration and by compensating the array uncertainties. Limitations of the previous methods are studied and a new method is proposed that keeps the simplicity of the blind beamformer structure and, at the same time, reduces tracking degradations while achieving millimetre level positioning accuracy in interference environments. To verify the applicability of the proposed method and analyze the degradations, array signals corresponding to the GPS L1 band are generated using a combination of hardware and software simulators. Furthermore, the amount of degradation and performance of the proposed method under different conditions are evaluated based on Monte Carlo simulations.

Relay testing parametric investigation of seismic fragility

International Nuclear Information System (INIS)

Bandyopadhyay, K.; Hofmayer, C.; Kassir, M.; Pepper, S.

1989-01-01

The seismic capacity of most electrical equipment is governed by malfunction of relays. An evaluation of the existing relay test data base at Brookhaven National Laboratory (BNL) has indicated that the seismic fragility of a relay may depend on various parameters related to the design or the input motion. In particular, the electrical mode, contact state, adjustment, chatter duration acceptance limit, and the frequency and the direction of the vibration input have been considered to influence the relay fragility level. For a particular relay type, the dynamics of its moving parts depends on the exact model number and vintage and hence, these parameters may also influence the fragility level. In order to investigate the effect of most of these parameters on the seismic fragility level, BNL has conducted a relay test program. The testing has been performed at Wyle Laboratories. Establishing the correlation between the single frequency fragility test input and the corresponding multifrequency response spectrum (TRS) is also an objective of this test program. This paper discusses the methodology used for testing and presents a brief summary of important test results. 1 ref., 10 figs

Performance Evaluation of Analog Beamforming with Hardware Impairments for mmW Massive MIMO Communication in an Urban Scenario

Directory of Open Access Journals (Sweden)

Sonia Gimenez

2016-09-01

Full Text Available The use of massive multiple-input multiple-output (MIMO techniques for communication at millimeter-Wave (mmW frequency bands has become a key enabler to meet the data rate demands of the upcoming fifth generation (5G cellular systems. In particular, analog and hybrid beamforming solutions are receiving increasing attention as less expensive and more power efficient alternatives to fully digital precoding schemes. Despite their proven good performance in simple setups, their suitability for realistic cellular systems with many interfering base stations and users is still unclear. Furthermore, the performance of massive MIMO beamforming and precoding methods are in practice also affected by practical limitations and hardware constraints. In this sense, this paper assesses the performance of digital precoding and analog beamforming in an urban cellular system with an accurate mmW channel model under both ideal and realistic assumptions. The results show that analog beamforming can reach the performance of fully digital maximum ratio transmission under line of sight conditions and with a sufficient number of parallel radio-frequency (RF chains, especially when the practical limitations of outdated channel information and per antenna power constraints are considered. This work also shows the impact of the phase shifter errors and combiner losses introduced by real phase shifter and combiner implementations over analog beamforming, where the former ones have minor impact on the performance, while the latter ones determine the optimum number of RF chains to be used in practice.

Performance analysis of distributed beamforming in a spectrum sharing system

KAUST Repository

Yang, Liang

2013-05-01

In this paper, we consider a distributed beamforming scheme (DBF) in a spectrum sharing system where multiple secondary users share the spectrum with some licensed primary users under an interference temperature constraint. We assume that the DBF is applied at the secondary users. We first consider optimal beamforming and compare it with the user selection scheme in terms of the outage probability and bit error rate performance metrics. Since perfect feedback is difficult to obtain, we then investigate a limited feedback DBF scheme and develop an analysis for a random vector quantization design algorithm. Specifically, the approximate statistics functions of the squared inner product between the optimal and quantized vectors are derived. With these statistics, we analyze the outage performance. Furthermore, the effects of channel estimation error and number of primary users on the system performance are investigated. Finally, optimal power adaptation and cochannel interference are considered and analyzed. Numerical and simulation results are provided to illustrate our mathematical formalism and verify our analysis. © 2012 IEEE.

Compact Beamformer Design with High Frame Rate for Ultrasound Imaging

Directory of Open Access Journals (Sweden)

Jun Luo

2014-04-01

Full Text Available In medical field, two-dimension ultrasound images are widely used in clinical diagnosis. Beamformer is critical in determining the complexity and performance of an ultrasound imaging system. Different from traditional means implemented with separated chips, a compact beamformer with 64 effective channels in a single moderate Field Programmable Gate Array has been presented in this paper. The compactness is acquired by employing receive synthetic aperture, harmonic imaging, time sharing and linear interpolation. Besides that, multi-beams method is used to improve the frame rate of the ultrasound imaging system. Online dynamic configuration is employed to expand system’s flexibility to two kinds of transducers with multi-scanning modes. The design is verified on a prototype scanner board. Simulation results have shown that on-chip memories can be saved and the frame rate can be improved on the case of 64 effective channels which will meet the requirement of real-time application.

A Two-Stage MMSE Beamformer for Underdetermined Signal Separation

Czech Academy of Sciences Publication Activity Database

Koldovský, Zbyněk; Tichavský, Petr; Phan, A. H.; Cichocki, A.

2013-01-01

Roč. 20, č. 12 (2013), s. 1227-1230 ISSN 1070-9908 Grant - others:GA ČR(CZ) GAP103/11/1947 Program:GA Institutional support: RVO:67985556 Keywords : beamforming * underdetermined mixtures * blind source separation Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 1.639, year: 2013 http://library.utia.cas.cz/separaty/2014/SI/koldovsky-0424112.pdf

Wide Area Protection Scheme Preventing Cascading Events based on Improved Impedance relay

DEFF Research Database (Denmark)

Liu, Zhou; Chen, Zhe; Sun, Haishun

2013-01-01

Load flow transferring after an initial contingency is regarded as one of the main reasons of causing unexpected cascading trips. A multi agent system (MAS) based wide area protection strategy is proposed in this paper to predict the load flow transferring from the point of view of impedance relays...

Body Loss Study of Beamforming Mode in LTE MIMO Mobile Terminals

DEFF Research Database (Denmark)

Zhang, Shuai; Zhao, Kun; Ying, Zhinong

2015-01-01

This paper mainly focuses on the investigation of the body loss of beamforming mode in LTE MIMO mobile terminals with CTIA user effects. The research of the body loss and radiation efficiency is carried out over different phase differences between two ports of each MIMO antenna. During studies......, four kinds of typical LTE MIMO antennas are used, namely, collocated ground free (GF), parallel GF, parallel on ground (OG) and orthogonal OG MIMO antennas, under four mobile terminal lengths at low and high frequencies. Two kinds of CTIA user effects are included in the research. From the studies......, the parallel GF MIMO antenna type exhibits the best beamforming performance in the four MIMO antenna types. In order to verify the simulations, envelope correlation coefficients of two MIMO antenna prototypes are measured. All the measured results agree well with the simulated....

Two-Hop Secure Communication Using an Untrusted Relay

Directory of Open Access Journals (Sweden)

Xiang He

2009-01-01

Full Text Available We consider a source-destination pair that can only communicate through an untrusted intermediate relay node. The intermediate node is willing to employ a designated relaying scheme to facilitate reliable communication between the source and the destination. Yet, the information it relays needs to be kept secret from it. In this two-hop communication scenario, where the use of the untrusted relay node is essential, we find that a positive secrecy rate is achievable. The center piece of the achievability scheme is the help provided by either the destination node with transmission capability, or an external “good samaritan” node. In either case, the helper performs cooperative jamming that confuses the eavesdropping relay and disables it from being able to decipher what it is relaying. We next derive an upper bound on the secrecy rate for this system. We observe that the gap between the upper bound and the achievable rate vanishes as the power of the relay node goes to infinity. Overall, the paper presents a case for intentional interference, that is, cooperative jamming, as an enabler for secure communication.

Energy-efficient relay selection and optimal power allocation for performance-constrained dual-hop variable-gain AF relaying

KAUST Repository

Zafar, Ammar; Radaydeh, Redha Mahmoud Mesleh; Chen, Yunfei; Alouini, Mohamed-Slim

2013-01-01

This paper investigates the energy-efficiency enhancement of a variable-gain dual-hop amplify-and-forward (AF) relay network utilizing selective relaying. The objective is to minimize the total consumed power while keeping the end-to-end signal

Application of a proposed overcurrent relay in radial distribution networks

Energy Technology Data Exchange (ETDEWEB)

Conde, A.; Vazquez, E. [Universidad Autonoma de Nuevo Leon, Facultad de Ingenieria Mecanica y Electrica, A.P. 36-F, CU, CP 66450, San Nicolas de los Garza, Nuevo Leon (Mexico)

2011-02-15

This paper contains the application criteria and coordination process for a proposed overcurrent relay in a radial power system with feed from one or multiple sources. This relay uses independent functions to detect faults and to calculate the operation time. Also this relay uses a time element function that allows it to reduce the time relay operation, enhancing the backup protection. Some of the proposed approaches improve the sensitivity of the relay. The selection of the best approach in the proposed relay is defined by the needs of the application. The proposed protection can be considered as an additional function protection to conventional overcurrent relays. (author)

Time of arrival based location estimation for cooperative relay networks

KAUST Repository

Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Hussain, Syed Imtiaz; Qaraqe, Khalid A.; Alouini, Mohamed-Slim

2010-01-01

In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

Time of arrival based location estimation for cooperative relay networks

KAUST Repository

Çelebi, Hasari Burak

2010-09-01

In this paper, we investigate the performance of a cooperative relay network performing location estimation through time of arrival (TOA). We derive Cramer-Rao lower bound (CRLB) for the location estimates using the relay network. The analysis is extended to obtain average CRLB considering the signal fluctuations in both relay and direct links. The effects of the channel fading of both relay and direct links and amplification factor and location of the relay node on average CRLB are investigated. Simulation results show that the channel fading of both relay and direct links and amplification factor and location of relay node affect the accuracy of TOA based location estimation. ©2010 IEEE.

Full-Duplex opportunistic relay selection in future spectrum-sharing networks

KAUST Repository

Khafagy, Mohammad Galal; Alouini, Mohamed-Slim; Aï ssa, Sonia

2015-01-01

We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Full-Duplex opportunistic relay selection in future spectrum-sharing networks

KAUST Repository

Khafagy, Mohammad Galal

2015-06-01

We propose and analyze the performance of full-duplex relay selection in primary/secondary spectrum-sharing networks. Contrary to half-duplex relaying, full-duplex relaying (FDR) enables simultaneous listening/forwarding at the secondary relay, thereby allowing for a higher spectral efficiency. However, since the source and relay simultaneously transmit in FDR, their superimposed signal at the primary receiver should now satisfy the existing interference constraint which can considerably limit the secondary network throughput. In this regard, relay selection can offer an adequate solution to boost the secondary throughput while satisfying the imposed interference limit. We first analyze the performance of opportunistic relay selection among a cluster of full-duplex decode-and-forward relays with self-interference by deriving the exact cumulative distribution function of its end-to-end signal-to-noise ratio. Second, we evaluate the end-to-end performance of relay selection with interference constraints due to the presence of a primary receiver. Finally, the presented exact theoretical findings are verified by numerical simulations.

Modeling the efficiency of Förster resonant energy transfer from energy relay dyes in dye-sensitized solar cells

KAUST Repository

Hoke, Eric T.

2010-02-11

Förster resonant energy transfer can improve the spectral breadth, absorption and energy conversion efficiency of dye sensitized solar cells. In this design, unattached relay dyes absorb the high energy photons and transfer the excitation to sensitizing dye molecules by Förster resonant energy transfer. We use an analytic theory to calculate the excitation transfer efficiency from the relay dye to the sensitizing dye accounting for dynamic quenching and relay dye diffusion. We present calculations for pores of cylindrical and spherical geometry and examine the effects of the Förster radius, the pore size, sensitizing dye surface concentration, collisional quenching rate, and relay dye lifetime. We find that the excitation transfer efficiency can easily exceed 90% for appropriately chosen dyes and propose two different strategies for selecting dyes to achieve record power conversion efficiencies. © 2010 Optical Society of America.

Discrete radioisotopic relays of a cyclic action

International Nuclear Information System (INIS)

Klempner, K.S.; Vasil'ev, A.G.

1975-01-01

A functional diagram of discrete radioisotopic relay equipment (RRP) with cyclic action was examined. An analysis of its rapid action and reliability under stationary conditions and transition regimes is presented. A structural diagram of radioisotopic relay equipment shows three radiation detectors, a pulse standardizer, an integrator and a power amplifier with a threshold cut-off device. It was established that the basic properties of the RRP - rapid action and reliability - are determined entirely by the counting rate of the average frequency of pulses from the radiation detector, n 0 and n 1 , in the 0 and 1 states (absence of current in the electromagnetic relay winding and activation of the winding of the output relay), capacities N 1 and N 2 of the dual counters, and the frequency of the transition threshold, f, of the generator. Formulas are presented which allow making engineering calculations for determining the optimum RRP parameters. High speed and reliability are shown, which are determined by the production purposes of the relay

Asymmetric Modulation Gains in Network Coded Relay Networks

DEFF Research Database (Denmark)

Roetter, Daniel Enrique Lucani; Fitzek, Frank

2015-01-01

Wireless relays have usually been considered in two ways. On the one hand, a physical layer approach focused on per-packet reliability and involving the relay on each packet transmission. On the other, recent approaches have relied on the judicious activation of the relay at the network level to ...

Comparisons of receive array interference reduction techniques under erroneous generalized transmit beamforming

KAUST Repository

Radaydeh, Redha Mahmoud; Alouini, Mohamed-Slim

2014-01-01

information for the desired user spatially uncorrelated transmit channels on the effectiveness of transmit beamforming for different interference reduction techniques is investigated. The case of over-loaded receive array with closely-spaced elements

Distance relay performance in future converter dominated power systems

DEFF Research Database (Denmark)

Sarkar, Moumita; Jia, Jundi; Yang, Guangya

2017-01-01

Increasing penetration of converter-based generations in power system has led to new system challenges. Short circuit power response from converter-based generations is different from that of traditional synchronous generators. Power electronic converters can be designed for over-current only up ...... of converter controls on fault current response of converter-based generations is also investigated. Index Terms—Converter control, distance relays, power system protection, system modelling....... to 1.1-1.25 times of its nominal value. Low availability of short circuit power can cause many challenges such as misoperation of distance relays. The aim of this paper is to investigate the effect of converter dominated systems on performance of distance relays. Backup functionality of the distance...... relay is major concern as miscoordination of backup relays in case of cascading faults can lead to severe stress in system, which can develop into blackout. In this paper, response of relays in traditional system is compared with response of relays in low short-circuit-current power systems. Impact...

Energy Efficiency and SINR Maximization Beamformers for Spectrum Sharing With Sensing Information

KAUST Repository

Alabbasi, AbdulRahman; Rezki, Zouheir; Shihada, Basem

2014-01-01

an underlaying communication using adaptive beamforming schemes combined with sensing information to achieve optimal energy-efficient systems. The proposed schemes maximize EE and SINR metrics subject to cognitive radio and quality-of-service constraints

Distributed stability control using intelligent voltage-margin relay

Energy Technology Data Exchange (ETDEWEB)

Wiszniewski, A.; Rebizant, W. [Wroclaw Univ. of Technology (Poland); Klimek, A. [Powertech Labs Inc., Surrey, BC (Canada)

2010-07-01

This paper presented an intelligent relay that operates if the load to source impedance ratio decreases to a level that is dangerously close to the stability limit, which leads to power system blackouts. The intelligent voltage-margin/difference relay installed at receiving substations automatically initiates action if the voltage stability margin drops to a dangerously low level. The relay decides if the tap changing devices are to be blocked and if under-voltage load shedding should be initiated, thereby mitigating an evolving instability. The intelligent relay has two levels of operation. At the first stage, which corresponds to the higher load to source impedance ratio, the relay initiates blocking of the tap changer. At the second stage, corresponding to the lower source to load impedance ratio, load shedding is initiated. The relay operates when the load to source impedance ratio reaches a certain predetermined level, but it does not depend either on the level of the source voltage or on the difference of source and load impedance phase angles. The algorithm for the relay is relatively simple and uses only locally available signals. Consequently, the transformer is well controlled to eliminate the cases of voltage instability. 6 refs., 7 figs.

Clinical evaluation of Synthetic Aperture Sequential Beamforming and Tissue Harmonic Imaging

DEFF Research Database (Denmark)

Brandt, Andreas Hjelm; Hemmsen, Martin Christian; Hansen, Peter Møller

2014-01-01

This study determines if the data reduction achieved by the combination Synthetic Aperture Sequential Beamforming (SASB) and Tissue Harmonic Imaging (THI) affects image quality. SASB-THI was evaluated against the combination of Dynamic Received Focusing and Tissue Harmonic Imaging (DRF-THI). A BK...... equally good image quality although a data reduction of 64 times is achieved with SASB-THI.......This study determines if the data reduction achieved by the combination Synthetic Aperture Sequential Beamforming (SASB) and Tissue Harmonic Imaging (THI) affects image quality. SASB-THI was evaluated against the combination of Dynamic Received Focusing and Tissue Harmonic Imaging (DRF-THI). A BK...... liver pathology were scanned to set a clinical condition, where ultrasonography is often performed. A total of 114 sequences were recorded and evaluated by five radiologists. The evaluators were blinded to the imaging technique, and each sequence was shown twice with different left-right positioning...

Directional synthetic aperture flow imaging using a dual stage beamformer approach

DEFF Research Database (Denmark)

Li, Ye; Jensen, Jørgen Arendt

2011-01-01

. The new method has been studied using the Field II simulations and experimental flow rig measurements. A linear array transducer with 7 MHz center frequency is used, and 64 elements are active to transmit and receive signals. The data is processed in two stages. The first stage has a fixed focus point......A new method for directional synthetic aperture flow imaging using a dual stage beamformer approach is presented. The velocity estimation is angle independent and the amount of calculations is reduced compared to full synthetic aperture, but still maintains all the advantages at the same time....... In the second stage, focal points are considered as virtual sources and data is beamformed along the flow direction. Then the velocities are estimated by finding the spatial shift between two signals. In the experimental measurements the angle between the transmit beam and flow vessel was 70 and a laminar flow...

Compressive Sound Speed Profile Inversion Using Beamforming Results

OpenAIRE

Youngmin Choo; Woojae Seong

2018-01-01

Sound speed profile (SSP) significantly affects acoustic propagation in the ocean. In this work, the SSP is inverted using compressive sensing (CS) combined with beamforming to indicate the direction of arrivals (DOAs). The travel times and the positions of the arrivals can be approximately linearized using their Taylor expansion with the shape function coefficients that parameterize the SSP. The linear relation between the travel times/positions and the shape function coefficients enables CS...

Asymptotic analysis for Nakagami-m fading channels with relay selection

KAUST Repository

Zhong, Caijun

2011-06-01

In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels. We derive their respective outage probability expressions in the asymptotic high signal-to-noise ratio (SNR) regime, from which the diversity order and coding gain are analyzed. In addition, we investigate the impact of power allocation between the source and relay terminals and derive the diversity-multiplexing tradeoff (DMT) for these relay selection systems. The theoretical findings suggest that partial relay selection can improve the diversity of the system and can achieve the same DMT as the "best" relay selection scheme under certain conditions. © 2011 IEEE.

Energy efficiency and SINR maximization beamformers for cognitive radio utilizing sensing information

KAUST Repository

Alabbasi, AbdulRahman; Rezki, Zouheir; Shihada, Basem

2014-01-01

communication using adaptive beamforming schemes combined with the sensing information to achieve an optimal energy efficient system. The proposed schemes maximize the energy efficiency and SINR metrics subject to cognitive radio and quality of service

LTE-Advanced Relay Technology and Standardization

CERN Document Server

Yuan, Yifei

2013-01-01

LTE-Advanced Relay Technology and Standardization provides a timely reference work for relay technology with the finalizing of LTE Release 10 specifications. LTE-Advanced is quickly becoming the global standard for 4G cellular communications. The relay technology, as one of the key features in LTE-Advanced, helps not only to improve the system coverage and capacity, but also to save the costs of laying wireline backhaul. As a leading researcher in the field of LTE-Advanced standards, the author provides an in-depth description of LTE-A relay technology, and explains in detail the standard specification and design principles.     Readers from both academic and industrial fields can find sections of interest to them: Sections 2 & 4 could benefit researchers in academia and those who are engaged in exploratory work, while Sections 3 & 4 are more useful to engineers. Dr. Yifei Yuan is the Technical Director at the Standards Department of ZTE Inc.

New results on performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim; Qaraqe, Khalid A.

2013-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

Accurate performance analysis of opportunistic decode-and-forward relaying

KAUST Repository

Tourki, Kamel; Yang, Hongchuan; Alouini, Mohamed-Slim

2011-01-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path may

Ka-Band Digital Beamforming and SweepSAR Demonstration for Ice and Solid Earth Topography

Science.gov (United States)

Sadowy, Gregory; Ghaemi, Hirad; Heavy, Brandon; Perkovic, Dragana; Quddus, Momin; Zawadzki, Mark; Moller, Delwyn

2010-01-01

GLISTIN is an instrument concept for a single-pass interferometric SAR operating at 35.6 GHz. To achieve large swath widths using practical levels of transmitter power, a digitally-beamformed planar waveguide array is used. This paper describes results from a ground-based demonstration of a 16-receiver prototype. Furthermore, SweepSAR is emerging as promising technique for achieving very wide swaths for surface change detection. NASA and DLR are studying this approach for the DESDynI and Tandem-L missions. SweepSAR employs a reflector with a digitally-beamformed array feed. We will describe development of an airborne demonstration of SweepSAR using the GLISTIN receiver array and a reflector.

Fetal MEG evoked response latency from beamformer with random field theory.

Science.gov (United States)

McCubbin, J; Vrba, J; Murphy, P; Temple, J; Eswaran, H; Lowery, C L; Preissl, H

2010-01-01

Analysis of fetal magnetoencephalographic brain recordings is restricted by low signal to noise ratio (SNR) and non-stationarity of the sources. Beamformer techniques have been applied to improve SNR of fetal evoked responses. However, until now the effect of non-stationarity was not taken into account in detail, because the detection of evoked responses is in most cases determined by averaging a large number of trials. We applied a windowing technique to improve the stationarity of the data by using short time segments recorded during a flash-evoked study. In addition, we implemented a random field theory approach for more stringent control of false-positives in the statistical parametric map of the search volume for the beamformer. The search volume was based on detailed individual fetal/maternal biometrics from ultrasound scans and fetal heart localization. Average power over a sliding window within the averaged evoked response against a randomized average background power was used as the test z-statistic. The significance threshold was set at 10% over all members of a contiguous cluster of voxels. There was at least one significant response for 62% of fetal and 95% of newborn recordings with gestational age (GA) between 28 and 45 weeks from 29 subjects. We found that the latency was either substantially unchanged or decreased with increasing GA for most subjects, with a nominal rate of about -11 ms/week. These findings support the anticipated neurophysiological development, provide validation for the beamformer model search as a methodology, and may lead to a clinical test for fetal cognitive development.

Electric equipment technical regulation on a relay

International Nuclear Information System (INIS)

1995-01-01

It is about a relay for power protection. It describes the definitions of structure, a point of contact protection of contact, reclosing, relay scheme and input circuit. It explains normal use condition, special use condition, rated frequency, rated voltage and rated current, fluctuation range of permission of incoming relay. It deals with general structing outer case, correction device, operation indicator and outer terminal condition sort and method of the test. It adds the marks and pictures about currents

Performance analysis of cognitive multihop relaying with m-QAM detect-and-forward in Nakagami-m fading channels

KAUST Repository

Benjillali, Mustapha; Hyadi, Amal; Da Costa, Daniel Benevides Da; Alouini, Mohamed-Slim

2013-01-01

In this work, we investigate the performance of cognitive multihop regenerative relaying systems in the "underlay" spectrum sharing scenario. The multiple relays perform "detect-and-forward" relaying strategy to convey a message with an order m quadrature amplitude modulation (m-QAM) from the source to the destination over independent but not necessarily identical Nakagami-m fading channels. We adopt a closed-form analysis framework based on univariate and bivariate Meijer G-functions to derive the end-to-end error performance (in terms of bit and symbol error rates), the outage probability, and the ergodic capacity. Various numerical examples are presented to illustrate the results with a large combination of system and fading parameters, and simulation results confirm the accuracy of our closed-form analysis. © 2013 IEEE.

Performance analysis of cognitive multihop relaying with m-QAM detect-and-forward in Nakagami-m fading channels

KAUST Repository

Benjillali, Mustapha

2013-09-01

In this work, we investigate the performance of cognitive multihop regenerative relaying systems in the "underlay" spectrum sharing scenario. The multiple relays perform "detect-and-forward" relaying strategy to convey a message with an order m quadrature amplitude modulation (m-QAM) from the source to the destination over independent but not necessarily identical Nakagami-m fading channels. We adopt a closed-form analysis framework based on univariate and bivariate Meijer G-functions to derive the end-to-end error performance (in terms of bit and symbol error rates), the outage probability, and the ergodic capacity. Various numerical examples are presented to illustrate the results with a large combination of system and fading parameters, and simulation results confirm the accuracy of our closed-form analysis. © 2013 IEEE.

Location-based Relay Selection and Power Adaptation Enabling Simultaneous Transmissions

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Madsen, Tatiana Kozlova; Schwefel, Hans-Peter

2010-01-01

Relaying is a well known technique to extend coverage and improve conditions for nodes in the outer coverage region. In this paper we propose a relaying scheme that exploits the spatial separation of relay and destination pairs to improve throughput by allowing simultaneous transmissions....... The proposed scheme is a cross-layer optimization for two-hop relaying that uses position information to jointly optimize relay selection and relay transmit power, maximizing Medium Access Control layer throughput. Further, in order to calculate the expected throughput, we apply a probabilistic model...... that takes into account MAC retransmissions and timing behavior of the IEEE 802.11 Distributed Coordination Function mode. Our results show an increase in throughput of approximately 20% is achievable for the proposed scheme when compared to two-hop relaying in the analyzed scenario....

BEAM-FORMING ERRORS IN MURCHISON WIDEFIELD ARRAY PHASED ARRAY ANTENNAS AND THEIR EFFECTS ON EPOCH OF REIONIZATION SCIENCE

Energy Technology Data Exchange (ETDEWEB)

Neben, Abraham R.; Hewitt, Jacqueline N.; Dillon, Joshua S.; Goeke, R.; Morgan, E. [Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Bradley, Richard F. [Dept. of Electrical and Computer Engineering, University of Virginia, Charlottesville, VA, 22904 (United States); Bernardi, G. [Square Kilometre Array South Africa (SKA SA), Cape Town 7405 (South Africa); Bowman, J. D. [School of Earth and Space Exploration, Arizona State University, Tempe, AZ 85287 (United States); Briggs, F. [Research School of Astronomy and Astrophysics, Australian National University, Canberra, ACT 2611 (Australia); Cappallo, R. J.; Corey, B. E.; Lonsdale, C. J.; McWhirter, S. R. [MIT Haystack Observatory, Westford, MA 01886 (United States); Deshpande, A. A. [Raman Research Institute, Bangalore 560080 (India); Greenhill, L. J. [Harvard-Smithsonian Center for Astrophysics, Cambridge, MA 02138 (United States); Hazelton, B. J.; Morales, M. F. [Department of Physics, University of Washington, Seattle, WA 98195 (United States); Johnston-Hollitt, M. [School of Chemical and Physical Sciences, Victoria University of Wellington, Wellington 6140 (New Zealand); Kaplan, D. L. [Department of Physics, University of Wisconsin–Milwaukee, Milwaukee, WI 53201 (United States); Mitchell, D. A. [CSIRO Astronomy and Space Science (CASS), P.O. Box 76, Epping, NSW 1710 (Australia); and others

2016-03-20

Accurate antenna beam models are critical for radio observations aiming to isolate the redshifted 21 cm spectral line emission from the Dark Ages and the Epoch of Reionization (EOR) and unlock the scientific potential of 21 cm cosmology. Past work has focused on characterizing mean antenna beam models using either satellite signals or astronomical sources as calibrators, but antenna-to-antenna variation due to imperfect instrumentation has remained unexplored. We characterize this variation for the Murchison Widefield Array (MWA) through laboratory measurements and simulations, finding typical deviations of the order of ±10%–20% near the edges of the main lobe and in the sidelobes. We consider the ramifications of these results for image- and power spectrum-based science. In particular, we simulate visibilities measured by a 100 m baseline and find that using an otherwise perfect foreground model, unmodeled beam-forming errors severely limit foreground subtraction accuracy within the region of Fourier space contaminated by foreground emission (the “wedge”). This region likely contains much of the cosmological signal, and accessing it will require measurement of per-antenna beam patterns. However, unmodeled beam-forming errors do not contaminate the Fourier space region expected to be free of foreground contamination (the “EOR window”), showing that foreground avoidance remains a viable strategy.

Performance of hybrid-ARQ with incremental redundancy over relay channels

KAUST Repository

Chelli, Ali

2012-12-01

In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears the transmitted messages over the different HARQ rounds and tries to decode the data packet. In case of successful decoding at the relay, both the relay and the source cooperate to transmit the message to the destination. A maximum number M of HARQ rounds is considered. The channel realizations are independent for different HARQ rounds. We assume Rayleigh fading channels for the links source-relay, source-destination, and relay-destination. We investigate the performance of HARQ-IR over relay channel from an information theoretic perspective. Analytical expressions are derived for the information outage probability, the average number of transmissions, and the average transmission rate. We illustrate through our investigation the benefit of relaying. We also show the impact of the target outage probability and the maximum number M of HARQ rounds on the outage probability, the average number of transmissions, and the average transmission rate. © 2012 IEEE.

Integrated 60GHz RF beamforming in CMOS

CERN Document Server

Yu, Yikun; van Roermund, Arthur H M

2011-01-01

""Integrated 60GHz RF Beamforming in CMOS"" describes new concepts and design techniques that can be used for 60GHz phased array systems. First, general trends and challenges in low-cost high data-rate 60GHz wireless system are studied, and the phased array technique is introduced to improve the system performance. Second, the system requirements of phase shifters are analyzed, and different phased array architectures are compared. Third, the design and implementation of 60GHz passive and active phase shifters in a CMOS technology are presented. Fourth, the integration of 60GHz phase shifters

RF-to-RF Characterization of a Phased Array Receive Antenna Steering System Using a Novel Ring Resonator-Based Integrated Photonic Beamformer

NARCIS (Netherlands)

Zhuang, L.; Burla, M.; Roeloffzen, C.G.H.; Meijerink, Arjan; Marpaung, D.A.I.; Khan, M.R.H.; van Etten, Wim; Leinse, Arne; Hoekman, M.; Heideman, Rene

2009-01-01

A novel ring resonator-based photonic beamformer has been developed for continuous and squint-free control of the reception angle of broadband phased array antenna systems. The core of the system is a ring resonator based optical beamforming network (OBFN) used for delay synchronization and coherent

On the jamming power allocation for secure amplify-and-forward relaying via cooperative jamming

KAUST Repository

Park, Kihong

2013-09-01

In this paper, we investigate secure communications in two-hop wireless relaying networks with one eavesdropper. To prevent the eavesdropper from intercepting the source message, the destination sends an intended jamming noise to the relay, which is referred to as cooperative jamming. This jamming noise helps protecting the source message from being captured reliably at the eavesdropper, while the destination cancels its self-intended noise. According to the channel information available at the destination, we derive three jamming power allocation strategies to minimize the outage probability of the secrecy rate. In addition, we derive analytic results quantifying the jamming power consumption of the proposed allocation methods. © 1983-2012 IEEE.

Artificial lateral-line system for imaging dipole sources using Beamforming techniques

NARCIS (Netherlands)

Dagamseh, A.M.K.; Wiegerink, Remco J.; Lammerink, Theodorus S.J.; Krijnen, Gijsbertus J.M.

In nature, fish have the ability to localize prey, school, navigate, etc. using the lateral-line organ [1]. Here we present the use of biomimetic artificial hair-based flow-sensors arranged as lateral-line system in combination with beamforming techniques for dipole source localization in air.

Energy efficiency and SINR maximization beamformers for cognitive radio utilizing sensing information

KAUST Repository

Alabbasi, Abdulrahman

2014-06-01

In this paper we consider a cognitive radio multi-input multi-output environment in which we adapt our beamformer to maximize both energy efficiency and signal to interference plus noise ratio (SINR) metrics. Our design considers an underlaying communication using adaptive beamforming schemes combined with the sensing information to achieve an optimal energy efficient system. The proposed schemes maximize the energy efficiency and SINR metrics subject to cognitive radio and quality of service constraints. Since the optimization of energy efficiency problem is not a convex problem, we transform it into a standard semi-definite programming (SDP) form to guarantee a global optimal solution. Analytical solution is provided for one scheme, while the other scheme is left in a standard SDP form. Selected numerical results are used to quantify the impact of the sensing information on the proposed schemes compared to the benchmark ones.

Cooperative Spatial Reuse with Transmit Beamforming in Multi-rate Wireless Networks

DEFF Research Database (Denmark)

Lu, Chenguang; Fitzek, Frank; Eggers, Patrick Claus F.

2009-01-01

We present a cooperative spatial reuse (CSR) scheme as a cooperative extension of the current TDMA-based MAC to enable spatial reuse in multi-rate wireless networks. We model spatial reuse as a cooperation problem on utilizing the time slots obtained from the TDMA-based MAC. In CSR, there are two...... operation modes. One is TDMA mode while the other is spatial reuse mode in which links transmit simultaneously. Links contribute their own time slots to form a cooperative group to do spatial reuse. Each link joins the group only if it can benefit in capacity or energy efficiency. Otherwise, the link...... will leave spatial reuse mode and switch back to TDMA. In this work, we focus on the transmit beamforming techniques to enable CSR by interference cancellation on MISO (Multiple Input Single Output) links. We compare the CSR scheme using zero-forcing (ZF) transmit beamforming, namely ZF-CSR, to the TDMA...

On Buffer-Aided Multiple-Access Relay Channel

DEFF Research Database (Denmark)

Liu, Rongkuan; Popovski, Petar; Wang, Gang

2016-01-01

This letter treats uplink scenario where M user equipments (UEs) send to a base station (BS), possibly via a common relay station (RS) that is equipped with a buffer. This is a multiple-access relay channel aided by a buffer. We devise a protocol in which the transmission mode is selected...... entirely at the BS, while simultaneously a number of UEs sends new messages to the BS. The results show that the adaptive selection of direct and buffer-aided relay transmissions leads to significant average throughput gains....

Cooperative AF Relaying in Spectrum-Sharing Systems: Outage Probability Analysis under Co-Channel Interferences and Relay Selection

KAUST Repository

Xia, Minghua

2012-11-01

For cooperative amplify-and-forward (AF) relaying in spectrum-sharing wireless systems, secondary users share spectrum resources originally licensed to primary users to communicate with each other and, thus, the transmit power of secondary transmitters is strictly limited by the tolerable interference powers at primary receivers. Furthermore, the received signals at a relay and at a secondary receiver are inevitably interfered by the signals from primary transmitters. These co-channel interferences (CCIs) from concurrent primary transmission can significantly degrade the performance of secondary transmission. This paper studies the effect of CCIs on outage probability of the secondary link in a spectrum-sharing environment. In particular, in order to compensate the performance loss due to CCIs, the transmit powers of a secondary transmitter and its relaying node are respectively optimized with respect to both the tolerable interference powers at the primary receivers and the CCIs from the primary transmitters. Moreover, when multiple relays are available, the technique of opportunistic relay selection is exploited to further improve system performance with low implementation complexity. By analyzing lower and upper bounds on the outage probability of the secondary system, this study reveals that it is the tolerable interference powers at primary receivers that dominate the system performance, rather than the CCIs from primary transmitters. System designers will benefit from this result in planning and designing next-generation broadband spectrum-sharing systems.

Relay self interference minimisation using tapped filter

KAUST Repository

Jazzar, Saleh; Al-Naffouri, Tareq Y.

2013-01-01

In this paper we introduce a self interference (SI) estimation and minimisation technique for amplify and forward relays. Relays are used to help forward signals between a transmitter and a receiver. This helps increase the signal coverage

Overlay Cognitive Radios With Channel-Aware Adaptive Link Selection and Buffer-Aided Relaying

KAUST Repository

Shaqfeh, Mohammad

2015-08-01

The aim of this work is to maximize the long-term average achievable rate region of a primary and a secondary source-destination pairs operating in an overlay setup over block-fading channels. To achieve this objective, we propose an opportunistic strategy to grant channel access to the primary and secondary sources based on the channel conditions in order to exploit the available multiple-link diversity gains in the system. The secondary source has causal knowledge of the primary messages and it acts as a relay of the primary source in return for getting access to the channel. To maximize the gains of relaying, the relay and destination are equipped with buffers to enable the use of channel-aware adaptive link selection. We propose and optimize different link selection policies and characterize their expected achievable rates. Also, we provide several numerical results to demonstrate the evident mutual benefits of buffer-aided cooperation and adaptive link selection to the primary and the secondary source-destination pairs. © 1972-2012 IEEE.

Overlay Cognitive Radios With Channel-Aware Adaptive Link Selection and Buffer-Aided Relaying

KAUST Repository

Shaqfeh, Mohammad; Zafar, Ammar; Alnuweiri, Hussein; Alouini, Mohamed-Slim

2015-01-01

The aim of this work is to maximize the long-term average achievable rate region of a primary and a secondary source-destination pairs operating in an overlay setup over block-fading channels. To achieve this objective, we propose an opportunistic strategy to grant channel access to the primary and secondary sources based on the channel conditions in order to exploit the available multiple-link diversity gains in the system. The secondary source has causal knowledge of the primary messages and it acts as a relay of the primary source in return for getting access to the channel. To maximize the gains of relaying, the relay and destination are equipped with buffers to enable the use of channel-aware adaptive link selection. We propose and optimize different link selection policies and characterize their expected achievable rates. Also, we provide several numerical results to demonstrate the evident mutual benefits of buffer-aided cooperation and adaptive link selection to the primary and the secondary source-destination pairs. © 1972-2012 IEEE.

Resource Allocation for the Multiband Relay Channel: A Building Block for Hybrid Wireless Networks

Directory of Open Access Journals (Sweden)

Kyounghwan Lee

2010-01-01

Full Text Available We investigate optimal resource allocation for the multiband relay channel. We find the optimal power and bandwidth allocation strategies that maximize the bounds on the capacity, by solving the corresponding max-min optimization problem. We provide sufficient conditions under which the associated max-min problem is equivalent to a supporting plane problem, which renders the solution for an arbitrary number of bands tractable. In addition, the sufficient conditions derived are general enough so that a class of utility functions can be accommodated with this formulation. As an example, we concentrate on the case where the source has two bands and the relay has a single band available and find the optimal resource allocation. We observe that joint power and bandwidth optimization always yields higher achievable rates than power optimization alone, establishing the merit of bandwidth sharing. Motivated by our analytical results, we examine a simple scenario where new channels become available for a transmitter to communicate; that is, new source to relay bands are added to a frequency division relay network. Given the channel conditions of the network, we establish the guidelines on how to allocate resources in order to achieve higher rates, depending on the relative quality of the available links.

76 FR 72124 - Internet-Based Telecommunications Relay Service Numbering

Science.gov (United States)

2011-11-22

... Docket No. 10-191; FCC 11-123] Internet-Based Telecommunications Relay Service Numbering AGENCY: Federal..., the information collection associated with the Commission's Internet- Based Telecommunications Relay... Telecommunications Relay Service Numbering, CG Docket No. 03-123; WC Docket No. 05-196; WC Docket No. 10-191; FCC 11...

Noise Quantification with Beamforming Deconvolution: Effects of Regularization and Boundary Conditions

DEFF Research Database (Denmark)

Lylloff, Oliver Ackermann; Fernandez Grande, Efren

Delay-and-sum (DAS) beamforming can be described as a linear convolution of an unknown sound source distribution and the microphone array response to a point source, i.e., point-spread function. Deconvolution tries to compensate for the influence of the array response and reveal the true source...

Using a micromachined magnetostatic relay in commutating a DC motor

Science.gov (United States)

Tai, Yu-Chong (Inventor); Wright, John A. (Inventor); Lilienthal, Gerald (Inventor)

2004-01-01

A DC motor is commutated by rotating a magnetic rotor to induce a magnetic field in at least one magnetostatic relay in the motor. Each relay is activated in response to the magnetic field to deliver power to at least one corresponding winding connected to the relay. In some cases, each relay delivers power first through a corresponding primary winding and then through a corresponding secondary winding to a common node. Specific examples include a four-pole, three-phase motor in which each relay is activated four times during one rotation of the magnetic rotor.

Relay-assited transmission and radio resource management for wireless networks

OpenAIRE

Agustín de Dios, Adrián

2008-01-01

La transmisión asistida por relay o transmisión cooperativa es una nueva técnica de diversidad espacial donde aparece un elemento nuevo (un relay o un usuario cooperativo) en la tradicional transmisión punto a punto (fuente a destino). Ahora en la comunicación intervienen tres enlaces: fuente-relay, relay-destino y fuente-destino. El relay, además de asistir a la fuente en la transmisión de un mensaje, permite combatir las degradaciones que puede sufrir el canal como el shadowing y el pathlos...

Optimized Policies for Improving Fairness of Location-based Relay Selection

DEFF Research Database (Denmark)

Nielsen, Jimmy Jessen; Olsen, Rasmus Løvenstein; Madsen, Tatiana Kozlova

2013-01-01

For WLAN systems in which relaying is used to improve throughput performance for nodes located at the cell edge, node mobility and information collection delays can have a significant impact on the performance of a relay selection scheme. In this paper we extend our existing Markov Chain modeling...... framework for relay selection to allow for efficient calculation of relay policies given either mean throughput or kth throughput percentile as optimization criterium. In a scenario with static access point, static relay, and a mobile destination node, the kth throughput percentile optimization...

Generalized instantly decodable network coding for relay-assisted networks

KAUST Repository

Elmahdy, Adel M.

2013-09-01

In this paper, we investigate the problem of minimizing the frame completion delay for Instantly Decodable Network Coding (IDNC) in relay-assisted wireless multicast networks. We first propose a packet recovery algorithm in the single relay topology which employs generalized IDNC instead of strict IDNC previously proposed in the literature for the same relay-assisted topology. This use of generalized IDNC is supported by showing that it is a super-set of the strict IDNC scheme, and thus can generate coding combinations that are at least as efficient as strict IDNC in reducing the average completion delay. We then extend our study to the multiple relay topology and propose a joint generalized IDNC and relay selection algorithm. This proposed algorithm benefits from the reception diversity of the multiple relays to further reduce the average completion delay in the network. Simulation results show that our proposed solutions achieve much better performance compared to previous solutions in the literature. © 2013 IEEE.

Optimal Contract Design for Cooperative Relay Incentive Mechanism under Moral Hazard

Directory of Open Access Journals (Sweden)

Nan Zhao

2015-01-01

Full Text Available Cooperative relay can effectively improve spectrum efficiency by exploiting the spatial diversity in the wireless networks. However, wireless nodes may acquire different network information with various users’ location and mobility, channels’ conditions, and other factors, which results in asymmetric information between the source and the relay nodes (RNs. In this paper, the relay incentive mechanism between relay nodes and the source is investigated under the asymmetric information. By modelling multiuser cooperative relay as a labour market, a contract model with moral hazard for relay incentive is proposed. To effectively incentivize the potential RNs to participate in cooperative relay, the optimization problems are formulated to maximize the source’s utility while meeting the feasible conditions under both symmetric and asymmetric information scenarios. Numerical simulation results demonstrate the effectiveness of the proposed contract design scheme for cooperative relay.

STUDI ANALISIS KOORDINASI OVER CURRENT RELAY (OCR DAN GROUND FAULT RELAY (GFR PADA RECLOSER DI SALURAN PENYULANG PENEBEL

Directory of Open Access Journals (Sweden)

I Dewa Gde Agung Budhi Udiana

2017-08-01

Full Text Available Short circuit causing over current problem and can might causing interference of the equipment performance such as distribution transformers also causing widespread disruption occurred. In resolving such interference is required as protection system on the distribution system. Seeing all above is needed coordination between the supporting component of the protection system which is consisted of Over Current Relay (OCR and Ground Fault Relay (GFR. The research was conducted at PT. PLN (Persero South Bali Area Network, INDONESIA on recloser in the feeder line of Penebel. OCR setting between the Relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana still less selective, with time value coordination between average security was still less than 0,2 second. Then OCR setting and GFR relay feeder of Penebel, Recloser Celagi, Recloser Bakisan, and Recloser Benana was recommended for re-setting in order to minimize disruption and electric power distribution system to be reliable.

Two-way CSI-assisted AF relaying with HPA nonlinearity

KAUST Repository

Qi, Jian

2015-09-11

In this paper, we investigate half-duplex two-way dual-hop channel state information (CSI)-assisted amplify-andforward (AF) relaying in the presence of high-power amplifier (HPA) nonlinearity at relays. The expression for the end-toend signal-to-noise ratio (SNR) is derived as per the modified system model by taking into account the interference caused by relaying scheme and HPA nonlinearity. The system performance of the considered relaying network is evaluated in terms of average symbol error probability (SEP) in Nakagami-m fading channels, by making use of the moment-generating function (MGF) approach. Numerical results are provided and show the effects of several parameters, such as quadrature amplitude modulation (QAM) order, number of relays, HPA parameters, and Nakagami parameter, on performance. © 2015 IEEE.

Transmit Antenna Selection for Multi-User Underlay Cognitive Transmission with Zero-Forcing Beamforming

KAUST Repository

Hanif, Muhammad; Yang, Hong-Chuan; Alouini, Mohamed-Slim

2017-01-01

We present a transmit antenna subset selection scheme for an underlay cognitive system serving multiple secondary receivers. The secondary system employs zero-forcing beamforming to nullify the interference to multiple primary users and eliminate

Robust Adaptive Beamforming with Sensor Position Errors Using Weighted Subspace Fitting-Based Covariance Matrix Reconstruction.

Science.gov (United States)

Chen, Peng; Yang, Yixin; Wang, Yong; Ma, Yuanliang

2018-05-08

When sensor position errors exist, the performance of recently proposed interference-plus-noise covariance matrix (INCM)-based adaptive beamformers may be severely degraded. In this paper, we propose a weighted subspace fitting-based INCM reconstruction algorithm to overcome sensor displacement for linear arrays. By estimating the rough signal directions, we construct a novel possible mismatched steering vector (SV) set. We analyze the proximity of the signal subspace from the sample covariance matrix (SCM) and the space spanned by the possible mismatched SV set. After solving an iterative optimization problem, we reconstruct the INCM using the estimated sensor position errors. Then we estimate the SV of the desired signal by solving an optimization problem with the reconstructed INCM. The main advantage of the proposed algorithm is its robustness against SV mismatches dominated by unknown sensor position errors. Numerical examples show that even if the position errors are up to half of the assumed sensor spacing, the output signal-to-interference-plus-noise ratio is only reduced by 4 dB. Beam patterns plotted using experiment data show that the interference suppression capability of the proposed beamformer outperforms other tested beamformers.

Spreading Sequence System for Full Connectivity Relay Network

Science.gov (United States)

Kwon, Hyuck M. (Inventor); Yang, Jie (Inventor); Pham, Khanh D. (Inventor)

2018-01-01

Fully connected uplink and downlink fully connected relay network systems using pseudo-noise spreading and despreading sequences subjected to maximizing the signal-to-interference-plus-noise ratio. The relay network systems comprise one or more transmitting units, relays, and receiving units connected via a communication network. The transmitting units, relays, and receiving units each may include a computer for performing the methods and steps described herein and transceivers for transmitting and/or receiving signals. The computer encodes and/or decodes communication signals via optimum adaptive PN sequences found by employing Cholesky decompositions and singular value decompositions (SVD). The PN sequences employ channel state information (CSI) to more effectively and more securely computing the optimal sequences.

Four-Way Relaying in Wireless Cellular Systems

DEFF Research Database (Denmark)

Liu, Huaping; Popovski, Petar; De Carvalho, Elisabeth

2013-01-01

Two-way relaying in wireless systems has initiated a large research effort during the past few years. Nevertheless, it represents only a specific traffic pattern and it is of interest to investigate other traffic patterns where such a simultaneous processing of information flows can bring...... performance advantage. In this paper we consider a \\emph{four-way relaying} scenario, where each of the two Mobile Stations (MSs) has a two-way connection to the same Base Station (BS), while each connection is through a dedicated Relay Station (RS). The RSs are placed in such a way that one RS...... of the new scheme for Decode-and-Forward (DF) operational model for the RS. We compare the performance with a state-of-the-art reference scheme, based on two-way relaying with DF. The results indicate that the achievable rate regions are significantly enlarged for the new scheme....

Performance analysis of underlay cognitive multihop regenerative relaying systems with multiple primary receivers

KAUST Repository

Hyadi, Amal

2013-12-01

Multihop relaying is an efficient strategy to improve the connectivity and extend the coverage area of secondary networks in underlay cognitive systems. In this work, we provide a comprehensive performance study of cognitive multihop regenerative relaying systems in an underlay spectrum sharing scenario with the presence of multiple primary receivers. Both interference power and peak power constraints are taken into account. In our analysis, all the links are subject to independent, non-identically distributed Nakagami-m fading. We derive closed-form expressions for the outage probability, high-order amount of fading, bit error rate, symbol error rate, and ergodic capacity. Different scenarios are presented to illustrate the obtained results and Monte Carlo simulations confirm the accuracy of our analytical derivations. © 2013 IEEE.

Systematic Network Coding with the Aid of a Full-Duplex Relay

DEFF Research Database (Denmark)

Giacaglia, Giuliano; Shi, Xiaomeng; Kim, MinJi

2013-01-01

is to deliver a given number of data packets to a receiver with the aid of a relay. The source broadcasts to both the receiver and the relay using one frequency, while the relay uses another frequency for transmissions to the receiver, allowing for a full-duplex operation of the relay. We analyze the decoding...... complexity and delay performance of two types of relays: one that preserves the systematic structure of the code from the source; another that does not. A systematic relay forwards uncoded packets upon reception, but transmits coded packets to the receiver after receiving the first coded packet from...

Mobile User Connectivity in Relay-Assisted Visible Light Communications

Directory of Open Access Journals (Sweden)

Petr Pešek

2018-04-01

Full Text Available In this paper, we investigate relay-assisted visible light communications (VLC where a mobile user acts as a relay and forwards data from a transmitter to the end mobile user. We analyse the utilization of the amplify-and-forward (AF and decode-and-forward (DF relaying schemes. The focus of the paper is on analysis of the behavior of the mobile user acting as a relay while considering a realistic locations of the receivers and transmitters on a standard mobile phone, more specifically with two photodetectors on both sides of a mobile phone and a transmitting LED array located upright. We also investigate dependency of the bit error rate (BER performance on the azimuth and elevation angles of the mobile relay device within a typical office environment. We provide a new analytical description of BER for AF and DF-based relays in VLC. In addition we compare AF and DF-based systems and show that DF offers a marginal improvement in the coverage area with a BER < 10–3 and a data rate of 100 Mb/s. Numerical results also illustrate that relay-based systems offer a significant improvement in terms of the coverage compared to direct non-line of sight VLC links.

Coded Cooperation for Multiway Relaying in Wireless Sensor Networks.

Science.gov (United States)

Si, Zhongwei; Ma, Junyang; Thobaben, Ragnar

2015-06-29

Wireless sensor networks have been considered as an enabling technology for constructing smart cities. One important feature of wireless sensor networks is that the sensor nodes collaborate in some manner for communications. In this manuscript, we focus on the model of multiway relaying with full data exchange where each user wants to transmit and receive data to and from all other users in the network. We derive the capacity region for this specific model and propose a coding strategy through coset encoding. To obtain good performance with practical codes, we choose spatially-coupled LDPC (SC-LDPC) codes for the coded cooperation. In particular, for the message broadcasting from the relay, we construct multi-edge-type (MET) SC-LDPC codes by repeatedly applying coset encoding. Due to the capacity-achieving property of the SC-LDPC codes, we prove that the capacity region can theoretically be achieved by the proposed MET SC-LDPC codes. Numerical results with finite node degrees are provided, which show that the achievable rates approach the boundary of the capacity region in both binary erasure channels and additive white Gaussian channels.

ESPRIT with multiple-angle subarray beamforming

Science.gov (United States)

Xu, Wen; Jiang, Ying; Zhang, Huiquan

2012-12-01

This article presents a new approach of implementing signal direction-of-arrival estimation, in which subarray beamforming is applied prior to estimation of signal parameters via rotational invariance techniques (ESPRIT). Different from the previous approaches, the beam-domain data from multiple adjacent pointing angles are combined in a way that the displacement invariance structure required by ESPRIT is maintained. It is intended to further obtain a sub-beamwidth resolution for a conventional multi-beam system already having small beamwidths. Computer simulations show that for typical multi-beam system applications the new approach provides improved estimation mean-square errors over the original ESPRIT, on top of reduced requirements for signal-to-noise ratio, number of snapshots, and computational time.

Non-invasive beamforming add-on module

KAUST Repository

Bader, Ahmed

2017-02-23

An embodiment of a non-invasive beamforming add-on apparatus couples to an existing antenna port and rectifies the beam azimuth in the upstream and downstream directions. The apparatus comprises input circuitry that is configured to receive one or more signals from a neighboring node of the linear wireless sensor network; first amplifier circuitry configured to adjust an amplitude of a respective received signal in accordance with a weighting coefficient and invoke a desired phase to a carrier frequency of the received signal thereby forming a first amplified signal; and second amplifier circuitry configured to adjust a gain of the first amplified signal towards upstream and downstream neighbors of the linear wireless sensor in the linear wireless sensor network.

47 CFR 11.20 - State Relay Network.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false State Relay Network. 11.20 Section 11.20... Network. This network is composed of State Relay (SR) sources, leased common carrier communications facilities or any other available communication facilities. The network distributes State EAS messages...

Cooperative AF Relaying in Spectrum-Sharing Systems: Performance Analysis under Average Interference Power Constraints and Nakagami-m Fading

KAUST Repository

Xia, Minghua

2012-06-01

Since the electromagnetic spectrum resource becomes more and more scarce, improving spectral efficiency is extremely important for the sustainable development of wireless communication systems and services. Integrating cooperative relaying techniques into spectrum-sharing cognitive radio systems sheds new light on higher spectral efficiency. In this paper, we analyze the end-to-end performance of cooperative amplify-and-forward (AF) relaying in spectrum-sharing systems. In order to achieve the optimal end-to-end performance, the transmit powers of the secondary source and the relays are optimized with respect to average interference power constraints at primary users and Nakagami-$m$ fading parameters of interference channels (for mathematical tractability, the desired channels from secondary source to relay and from relay to secondary destination are assumed to be subject to Rayleigh fading). Also, both partial and opportunistic relay-selection strategies are exploited to further enhance system performance. Based on the exact distribution functions of the end-to-end signal-to-noise ratio (SNR) obtained herein, the outage probability, average symbol error probability, diversity order, and ergodic capacity of the system under study are analytically investigated. Our results show that system performance is dominated by the resource constraints and it improves slowly with increasing average SNR. Furthermore, larger Nakagami-m fading parameter on interference channels deteriorates system performance slightly. On the other hand, when interference power constraints are stringent, opportunistic relay selection can be exploited to improve system performance significantly. All analytical results are corroborated by simulation results and they are shown to be efficient tools for exact evaluation of system performance.

On UWB beamforming

Directory of Open Access Journals (Sweden)

T. Kaiser

2004-01-01

Full Text Available Ultra-Wideband (UWB communication systems and Multi-Input-Multi-Output (MIMO techniques rank among the few emerging key technologies in wireless communications. For that reason the marriage of these two complementary approaches should deserve attention. Apparently, the extremely large ultra-wide bandwidth creates rich multipath diversity which calls, at a first glance, additional antenna elements into question. However, another point of view is as follows. The attenuation by solid materials usually increases with increasing frequency; e.g. frequencies above, say, 10 GHz are considered to be blocked by walls etc. Since UWB can occupy more than 7 GHz of bandwidth (according to FCC regularisation the performance of a communication link can be physically extended only by adding spatial information, i.e. multiple antennas, even if such extension may play a minor role. From this point of view UWB& MIMO presents an upper physical bound for indoor communications and is therefore at least worth to be investigated. In order to see the forest for the trees, we will focus in this limited contribution on beamforming among all alternative MIMO techniques (like space time coding or spatial multiplexing.

SIMULASI SISTEM KELISTRIKAN KAMAR HOTEL MENGGUNAKAN SMART RELAY

Directory of Open Access Journals (Sweden)

I Nyoman Sukarma

2018-03-01

Full Text Available Fungsi dari alat key tag atau hotel switch atau key card adalah memutus atau menyambungkan aliran listrik ke dalam suatu area tertentu atau ruang. Key tag memiliki peran penting pada kamar hotel untuk mencegah pemborosan energi pada saat kamar hotel tidak berpenghuni atau belum tersewakan. Untuk itu, penulis merancang simulasi sistem kelistrikan pada kamar hotel yang dikontrol dengan smart relay. Pada simulasi ini digunakan smart relay Zelio Logic buatan Schneider Electric. Pemrograman smart relay ini menggunakan ladder diagram yang disusun menggunakan perangkat lunak ZelioSoft2 dari Schneider Electric. Smart relay menerima sinyal masukan dari sensor, key tag dan sakelar. Sinyal masukan tersebut selanjutnya diproses agar lampu, kotak-kontak, exhaust fan, dan AC (Air Conditioner pada kamar hotel dapat bekerja.

Performance of hybrid-ARQ with incremental redundancy over relay channels

KAUST Repository

Chelli, Ali; Alouini, Mohamed-Slim

2012-01-01

In this paper, we consider a relay network consisting of a source, a relay, and a destination. The source transmits a message to the destination using hybrid automatic repeat request (HARQ) with incremental redundancy (IR). The relay overhears

Asymptotic analysis for Nakagami-m fading channels with relay selection

KAUST Repository

Zhong, Caijun; Wong, Kaikit; Jin, Shi; Alouini, Mohamed-Slim; Ratnarajah, Tharm

2011-01-01

In this paper, we analyze the asymptotic outage probability performance of both decode-and-forward (DF) and amplify-and-forward (AF) relaying systems using partial relay selection and the "best" relay selection schemes for Nakagami-m fading channels

Efficient Resource Scheduling by Exploiting Relay Cache for Cellular Networks

Directory of Open Access Journals (Sweden)

Chun He

2015-01-01

Full Text Available In relay-enhanced cellular systems, throughput of User Equipment (UE is constrained by the bottleneck of the two-hop link, backhaul link (or the first hop link, and access link (the second hop link. To maximize the throughput, resource allocation should be coordinated between these two hops. A common resource scheduling algorithm, Adaptive Distributed Proportional Fair, only ensures that the throughput of the first hop is greater than or equal to that of the second hop. But it cannot guarantee a good balance of the throughput and fairness between the two hops. In this paper, we propose a Two-Hop Balanced Distributed Scheduling (TBS algorithm by exploiting relay cache for non-real-time data traffic. The evolved Node Basestation (eNB adaptively adjusts the number of Resource Blocks (RBs allocated to the backhaul link and direct links based on the cache information of relays. Each relay allocates RBs for relay UEs based on the size of the relay UE’s Transport Block. We also design a relay UE’s ACK feedback mechanism to update the data at relay cache. Simulation results show that the proposed TBS can effectively improve resource utilization and achieve a good trade-off between system throughput and fairness by balancing the throughput of backhaul and access link.

Synthetic Aperture Sequential Beamformation applied to medical imaging

DEFF Research Database (Denmark)

Hemmsen, Martin Christian; Hansen, Jens Munk; Jensen, Jørgen Arendt

2012-01-01

Synthetic Aperture Sequential Beamforming (SASB) is applied to medical ultrasound imaging using a multi element convex array transducer. The main motivation for SASB is to apply synthetic aperture techniques without the need for storing RF-data for a number of elements and hereby devise a system...... with a reduced system complexity. Using a 192 element, 3.5 MHz, λ-pitch transducer, it is demonstrated using tissue-phantom and wire-phantom measurements, how the speckle size and the detail resolution is improved compared to conventional imaging....

Wireless Energy Harvesting Two-Way Relay Networks with Hardware Impairments.

Science.gov (United States)

Peng, Chunling; Li, Fangwei; Liu, Huaping

2017-11-13

This paper considers a wireless energy harvesting two-way relay (TWR) network where the relay has energy-harvesting abilities and the effects of practical hardware impairments are taken into consideration. In particular, power splitting (PS) receiver is adopted at relay to harvests the power it needs for relaying the information between the source nodes from the signals transmitted by the source nodes, and hardware impairments is assumed suffered by each node. We analyze the effect of hardware impairments [-20]on both decode-and-forward (DF) relaying and amplify-and-forward (AF) relaying networks. By utilizing the obtained new expressions of signal-to-noise-plus-distortion ratios, the exact analytical expressions of the achievable sum rate and ergodic capacities for both DF and AF relaying protocols are derived. Additionally, the optimal power splitting (OPS) ratio that maximizes the instantaneous achievable sum rate is formulated and solved for both protocols. The performances of DF and AF protocols are evaluated via numerical results, which also show the effects of various network parameters on the system performance and on the OPS ratio design.

Two-Way Multi-Antenna Relaying with Simultaneous Wireless Information and Power Transfer

Directory of Open Access Journals (Sweden)

Thanaphat Srivantana

2017-03-01

Full Text Available In this paper, we propose various kinds of two-way multi-antenna relaying with simultaneous wireless information and power transfer (SWIPT and investigate their performance. Specifically, we first consider a two-way relay network where two single-antenna end nodes communicate with each other through a multi-antenna relay node that is energy constrained. This relay node harvests energy from the two end nodes and use the harvested energy for forwarding their information. Six relaying schemes that support the considered network then build on the power splitting-based relaying and time switching-based relaying protocols. The average bit error rates of these schemes are evaluated and compared by computer simulations considering several network parameters, including the number of relay antennas, power splitting ratio, and energy harvesting time. Such evaluation and comparison provide useful insights into the performance of SWIPT-based two-way multi-antenna relaying.

Developing a Domain Model for Relay Circuits

DEFF Research Database (Denmark)

Haxthausen, Anne Elisabeth

2009-01-01

In this paper we stepwise develop a domain model for relay circuits as used in railway control systems. First we provide an abstract, property-oriented model of networks consisting of components that can be glued together with connectors. This model is strongly inspired by a network model...... for railways madeby Bjørner et.al., however our model is more general: the components can be of any kind and can later be refined to e.g. railway components or circuit components. Then we show how the abstract network model can be refined into an explicit model for relay circuits. The circuit model describes...... the statics as well as the dynamics of relay circuits, i.e. how a relay circuit can be composed legally from electrical components as well as how the components may change state over time. Finally the circuit model is transformed into an executable model, and we show how a concrete circuit can be defined...

An RSS based location estimation technique for cognitive relay networks

KAUST Repository

Qaraqe, Khalid A.; Hussain, Syed Imtiaz; Ç elebi, Hasari Burak; Abdallah, Mohamed M.; Alouini, Mohamed-Slim

2010-01-01

In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine

Breaking the Myth That Relay Swimming Is Faster Than Individual Swimming.

Science.gov (United States)

Skorski, Sabrina; Etxebarria, Naroa; Thompson, Kevin G

2016-04-01

To investigate if swimming performance is better in a relay race than in the corresponding individual race. The authors analyzed 166 elite male swimmers from 15 nations in the same competition (downloaded from www.swimrankings.net). Of 778 observed races, 144 were Olympic Games performances (2000, 2004, 2012), with the remaining 634 performed in national or international competitions. The races were 100-m (n = 436) and 200-m (n = 342) freestyle events. Relay performance times for the 2nd-4th swimmers were adjusted (+ 0.73 s) to allow for the "flying start." Without any adjustment, mean individual relay performances were significantly faster for the first 50 m and overall time in the 100-m events. Furthermore, the first 100 m of the 200-m relay was significantly faster (P > .001). During relays, swimmers competing in 1st position did not show any difference compared with their corresponding individual performance (P > .16). However, swimmers competing in 2nd-4th relay-team positions demonstrated significantly faster times in the 100-m (P individual events (P team positions were adjusted for the flying start no differences were detected between relay and individual race performance for any event or split time (P > .17). Highly trained swimmers do not swim (or turn) faster in relay events than in their individual races. Relay exchange times account for the difference observed in individual vs relay performance.

Scalable DeNoise-and-Forward in Bidirectional Relay Networks

DEFF Research Database (Denmark)

Sørensen, Jesper Hemming; Krigslund, Rasmus; Popovski, Petar

2010-01-01

In this paper a scalable relaying scheme is proposed based on an existing concept called DeNoise-and-Forward, DNF. We call it Scalable DNF, S-DNF, and it targets the scenario with multiple communication flows through a single common relay. The idea of the scheme is to combine packets at the relay...... in order to save transmissions. To ensure decodability at the end-nodes, a priori information about the content of the combined packets must be available. This is gathered during the initial transmissions to the relay. The trade-off between decodability and number of necessary transmissions is analysed...

Non-orthogonal transmission in multi-user systems with Grassmannian beamforming

KAUST Repository

Xia, Minghua

2011-06-01

Aiming to achieve the sum-rate capacity in multiuser multi-input multi-output (MIMO) channels with N t antennas implemented at the transmitter, opportunistic beamforming (OBF) generates N t orthonormal beams and serves N t users during each transmission, which results in high scheduling delay over the users, especially in densely populated wireless networks. Non-orthogonal OBF with more than N t transmit beams can be exploited to serve more users simultaneously and further decreases scheduling delay. However, the inter-beam interference will inevitably deteriorate the sum-rate. Therefore, there is a tradeoff between the sum-rate and the increasing number of transmit beams. In this context, the sum-rate of non-orthogonal OBF with N > N t beams are studied, where the transmitter is based on the Grassmannian beamforming. Our results show that non-orthogonal OBF is an interference-limited system. Moreover, when the inter-beam interference reaches its minimum for fixed N t and N, the sum-rate scales as N ln (N/N-N t) and it decreases monotonically with N for fixed N t. Numerical results corroborate the accuracy of our analyses. © 2011 IEEE.

Effects of relay chatter in seismic probabilistic safety analysis

International Nuclear Information System (INIS)

Reed, J.W.; Shiu, K.K.

1985-01-01

In the Zion and Indian Point Probabilistic Safety Studies, relay chatter was dismissed as a credible event and hence was not formally included in the analyses. Although little discussion is given in the Zion and Indian Point PSA documentation concerning the basis for this decision, it has been expressed informally that it was assumed that the operators will be able to reset all relays in a timely manner. Currently, it is the opinion of many professionals that this may be an oversimplification. The three basic areas which must be considered in addressing relay chatter include the fragility of the relays per se, the reliability of the operators to reset the relays and finally the systems response aspects. Each of these areas is reviewed and the implications for seismic PSA are discussed. Finally, recommendations for future research are given

Clinical evaluation of synthetic aperture sequential beamforming ultrasound in patients with liver tumors

DEFF Research Database (Denmark)

Hansen, Peter Møller; Hemmsen, Martin Christian; Brandt, Andreas Hjelm

2014-01-01

Medical ultrasound imaging using synthetic aperture sequential beamforming (SASB) has for the first time been used for clinical patient scanning. Nineteen patients with cancer of the liver (hepatocellular carcinoma or colorectal liver metastases) were scanned simultaneously with conventional...

Securing Communication via Transmission of Artificial Noise by Both Sides: Bipolar-Beamforming Optimization

Directory of Open Access Journals (Sweden)

Yongkai Zhou

2013-01-01

Full Text Available The paper considers the secure transmission in a wireless environment in which both the transmitter (Alice and the legitimate receiver (Bob send artificial noise (AN to interfere with the eavesdropper (Eve. Optimal design is analyzed in detail for this AN-by-both-side model to deal with Eve’s stochastic channel condition and random spatial distribution. Bipolar-beamforming is first proposed to jointly design Alice and Bob’s transmitting signals. By optimally assigning the transmitting antenna for Bob and allocating the power ratio between Alice’s information and the AN signal, maximum secrecy capacity can be achieved. Simulation is done to illustrate the process of bipolar-beamforming optimization. Results show that the AN-by-both-side model has good secrecy performance on both average and extreme conditions as Eve approaches Alice or Bob.

76 FR 65965 - Contributions to the Telecommunications Relay Services Fund

Science.gov (United States)

2011-10-25

...] Contributions to the Telecommunications Relay Services Fund AGENCY: Federal Communications Commission. ACTION... Telecommunications Relay Services (TRS) Fund in a manner prescribed by regulation that is consistent with and... . SUPPLEMENTARY INFORMATION: This is a summary of the Commission's Contributions to the Telecommunications Relay...

Energy Efficiency and SINR Maximization Beamformers for Spectrum Sharing With Sensing Information

KAUST Repository

Alabbasi, Abdulrahman

2014-09-01

In this paper, we consider a cognitive radio multi-input-multi-output environment, in which we adapt our beamformer to maximize both energy efficiency (EE) and signal-to-interference-plus-noise ratio (SINR) metrics. Our design considers an underlaying communication using adaptive beamforming schemes combined with sensing information to achieve optimal energy-efficient systems. The proposed schemes maximize EE and SINR metrics subject to cognitive radio and quality-of-service constraints. The analysis of the proposed schemes is classified into two categories based on knowledge of the secondary-transmitter-to-primary-receiver channel. Since the optimizations of EE and SINR problems are not convex problems, we transform them into a standard semidefinite programming (SDP) form to guarantee that the optimal solutions are global. An analytical solution is provided for one scheme, while the second scheme is left in a standard SDP form. Selected numerical results are used to quantify the impact of the sensing information on the proposed schemes compared to the benchmark ones.

Relay selection in underlay cognitive networks with fixed transmission power nodes

KAUST Repository

Hussain, Syed Imtiaz

2013-07-31

Underlay cognitive networks operate simultaneously with primary networks satisfying stringent interference constraints, which reduces their transmission power and coverage area. To reach remote destinations, secondary sources use relaying techniques. Selecting the best relay among the available ones is a well known technique. Recently, selective cooperation is investigated in cognitive networks where the secondary nodes can adapt their transmission power to always satisfy the interference threshold. In this paper, we investigate a situation where the secondary nodes have a fixed transmission power and may violate the interference threshold. We present two relay selection schemes; the first one excludes the relays not satisfying the interference constraint and then picks up a relay from the remaining ones that can provide the maximum signal-to-noise ratio (SNR). The other scheme uses a quotient of the relay link SNR and the interference from the relay to the primary user and optimizes it to maximise the relay link SNR. We derive closed form expressions for outage probability, bit error rate, channel capacity and diversity of the system for both schemes by using tight approximations. We also study mutual effects of interference. Simulation results confirm the analytical results and reveal that the relay selection is feasible at low SNRs. Copyright © 2013 John Wiley & Sons, Ltd.

Bilayer Protograph Codes for Half-Duplex Relay Channels

Science.gov (United States)

Divsalar, Dariush; VanNguyen, Thuy; Nosratinia, Aria

2013-01-01

Direct to Earth return links are limited by the size and power of lander devices. A standard alternative is provided by a two-hops return link: a proximity link (from lander to orbiter relay) and a deep-space link (from orbiter relay to Earth). Although direct to Earth return links are limited by the size and power of lander devices, using an additional link and a proposed coding for relay channels, one can obtain a more reliable signal. Although significant progress has been made in the relay coding problem, existing codes must be painstakingly optimized to match to a single set of channel conditions, many of them do not offer easy encoding, and most of them do not have structured design. A high-performing LDPC (low-density parity-check) code for the relay channel addresses simultaneously two important issues: a code structure that allows low encoding complexity, and a flexible rate-compatible code that allows matching to various channel conditions. Most of the previous high-performance LDPC codes for the relay channel are tightly optimized for a given channel quality, and are not easily adapted without extensive re-optimization for various channel conditions. This code for the relay channel combines structured design and easy encoding with rate compatibility to allow adaptation to the three links involved in the relay channel, and furthermore offers very good performance. The proposed code is constructed by synthesizing a bilayer structure with a pro to graph. In addition to the contribution to relay encoding, an improved family of protograph codes was produced for the point-to-point AWGN (additive white Gaussian noise) channel whose high-rate members enjoy thresholds that are within 0.07 dB of capacity. These LDPC relay codes address three important issues in an integrative manner: low encoding complexity, modular structure allowing for easy design, and rate compatibility so that the code can be easily matched to a variety of channel conditions without extensive

Acoustic Emission Beamforming for Detection and Localization of Damage

Science.gov (United States)

Rivey, Joshua Callen

The aerospace industry is a constantly evolving field with corporate manufacturers continually utilizing innovative processes and materials. These materials include advanced metallics and composite systems. The exploration and implementation of new materials and structures has prompted the development of numerous structural health monitoring and nondestructive evaluation techniques for quality assurance purposes and pre- and in-service damage detection. Exploitation of acoustic emission sensors coupled with a beamforming technique provides the potential for creating an effective non-contact and non-invasive monitoring capability for assessing structural integrity. This investigation used an acoustic emission detection device that employs helical arrays of MEMS-based microphones around a high-definition optical camera to provide real-time non-contact monitoring of inspection specimens during testing. The study assessed the feasibility of the sound camera for use in structural health monitoring of composite specimens during tensile testing for detecting onset of damage in addition to nondestructive evaluation of aluminum inspection plates for visualizing stress wave propagation in structures. During composite material monitoring, the sound camera was able to accurately identify the onset and location of damage resulting from large amplitude acoustic feedback mechanisms such as fiber breakage. Damage resulting from smaller acoustic feedback events such as matrix failure was detected but not localized to the degree of accuracy of larger feedback events. Findings suggest that beamforming technology can provide effective non-contact and non-invasive inspection of composite materials, characterizing the onset and the location of damage in an efficient manner. With regards to the nondestructive evaluation of metallic plates, this remote sensing system allows us to record wave propagation events in situ via a single-shot measurement. This is a significant improvement over

Implementation of a Relay Coordination System for the Mars Network

Science.gov (United States)

Allard, Daniel A.

2010-01-01

Mars network relay operations involve the coordination of lander and orbiter teams through long-term and short-term planning, tactical changes and post-pass analysis. Much of this coordination is managed through email traffic and point-to-point file data exchanges. It is often difficult to construct a complete and accurate picture of the relay situation at any given moment, as there is no centralized store of correlated relay data. The Mars Relay Operations Service (MaROS) is being implemented to address the problem of relay coordination for current and next-generation relay missions. The service is provided for the purpose of coordinating communications sessions between landed spacecraft assets and orbiting spacecraft assets at Mars. The service centralizes a set of functions previously distributed across multiple spacecraft operations teams, and as such greatly improves visibility into the end-to-end strategic coordination process. Most of the process revolves around the scheduling of communications sessions between the spacecraft during periods of time when a landed asset on Mars is geometrically visible by an orbiting spacecraft. These "relay" sessions are used to transfer data both to and from the landed asset via the orbiting asset on behalf of Earth-based spacecraft operators. This paper will discuss the relay coordination problem space, overview the architecture and design selected to meet system requirements, and describe the first phase of system implementation

Screening test of relays used under pressurized sulfur hexafluoride (SF6)

International Nuclear Information System (INIS)

Kutsukake, Kenichi; Matsuda, Makoto; Hanashima, Susumu; Obara, Kenjiro

2008-01-01

Many measurement and control devices inside of a high voltage terminal of the JAEA-Tokai tandem accelerator are operated under pressurized sulfur hexafluoride gas (SF 6 ) of 0.5 MPa. This screening test has been carried out to select a relay, which is usable under the pressurized SF 6 for turn on and off a large current of the devices, from commercial relays used in the atmospheric condition. Four kinds of relays were tested: electromechanical relay (EMR), magnet contactor (MAG), solid-state relay (SSR) and hybrid relay (HYB). Temperature and appearance changes of the relay were collected as measurement items. In addition, a reason of contact trouble of the relays was considered from the results of qualitative elementary analysis and observation of the contact surface using the EDS (energy-dispersive X-ray spectroscopy) and the SEM (scanning electron microscope). As a result, the EMR and the MAG showed irregular contact in spite of input voltage and electric current had fed to an operational coil of the relay normally. It is caused by the sulfide or fluoride compounds, which were formed by chemical reaction between metals and sulfur or hydrogen fluoride due to dissociation of SF 6 in electric arcs. On the other hand, the performance of the SSR and the HYB is better than the EMR and the MAG, and it was found that these relays are available in the pressurized SF 6 of 0.5MPa in spite of the standard specification. (author)

Relay-based information broadcast in complex networks

Science.gov (United States)

Fan, Zhongyan; Han, Zeyu; Tang, Wallace K. S.; Lin, Dong

2018-04-01

Information broadcast (IB) is a critical process in complex network, usually accomplished by flooding mechanism. Although flooding is simple and no prior topological information is required, it consumes a lot of transmission overhead. Another extreme is the tree-based broadcast (TB), for which information is disseminated via a spanning tree. It achieves the minimal transmission overhead but the maintenance of spanning tree for every node is an obvious obstacle for implementation. Motivated by the success of scale-free network models for real-world networks, in this paper, we investigate the issues in IB by considering an alternative solution in-between these two extremes. A novel relay-based broadcast (RB) mechanism is proposed by employing a subset of nodes as relays. Information is firstly forwarded to one of these relays and then re-disseminated to others through the spanning tree whose root is the relay. This mechanism provides a trade-off solution between flooding and TB. On one hand, it saves up a lot of transmission overhead as compared to flooding; on the other hand, it costs much less resource for maintenance than TB as only a few spanning trees are needed. Based on two major criteria, namely the transmission overhead and the convergence time, the effectiveness of RB is confirmed. The impacts of relay assignment and network structures on performance are also studied in this work.

Ultrasonic Fingerprint Sensor With Transmit Beamforming Based on a PMUT Array Bonded to CMOS Circuitry.

Science.gov (United States)

Jiang, Xiaoyue; Tang, Hao-Yen; Lu, Yipeng; Ng, Eldwin J; Tsai, Julius M; Boser, Bernhard E; Horsley, David A

2017-09-01

In this paper, we present a single-chip 65 ×42 element ultrasonic pulse-echo fingerprint sensor with transmit (TX) beamforming based on piezoelectric micromachined ultrasonic transducers directly bonded to a CMOS readout application-specific integrated circuit (ASIC). The readout ASIC was realized in a standard 180-nm CMOS process with a 24-V high-voltage transistor option. Pulse-echo measurements are performed column-by-column in sequence using either one column or five columns to TX the ultrasonic pulse at 20 MHz. TX beamforming is used to focus the ultrasonic beam at the imaging plane where the finger is located, increasing the ultrasonic pressure and narrowing the 3-dB beamwidth to [Formula: see text], a factor of 6.4 narrower than nonbeamformed measurements. The surface of the sensor is coated with a poly-dimethylsiloxane (PDMS) layer to provide good acoustic impedance matching to skin. Scanning laser Doppler vibrometry of the PDMS surface was used to map the ultrasonic pressure field at the imaging surface, demonstrating the expected increase in pressure, and reduction in beamwidth. Imaging experiments were conducted using both PDMS phantoms and real fingerprints. The average image contrast is increased by a factor of 1.5 when beamforming is used.

Cooperative relay-based multicasting for energy and delay minimization

KAUST Repository

Atat, Rachad

2012-08-01

Relay-based multicasting for the purpose of cooperative content distribution is studied. Optimized relay selection is performed with the objective of minimizing the energy consumption or the content distribution delay within a cluster of cooperating mobiles. Two schemes are investigated. The first consists of the BS sending the data only to the relay, and the second scheme considers the scenario of threshold-based multicasting by the BS, where a relay is selected to transmit the data to the mobiles that were not able to receive the multicast data. Both schemes show significant superiority compared to the non-cooperative scenarios, in terms of energy consumption and delay reduction. © 2012 IEEE.

Analog 65/130 nm CMOS 5 GHz Sub-Arrays with ROACH-2 FPGA Beamformers for Hybrid Aperture-Array Receivers

Science.gov (United States)

2017-03-20

factor, where c is the wave speed . Proposed two-level hybrid beamforming architecture consists of an analog sub-array at level-1 (L-element analog...gigabit transceivers, to support 4x10Ge links (SFP+) for high- speed communication. ROACH-2 also supports two ZDOk+ interfaces supporting high speed ADCs...antenna systems with hybrid analog and digital beamforming for millimeter wave 5G ,” IEEE Communications Magazine, vol. 53, no. 1, pp. 186–194, January

Loudness estimation of simultaneous sources using beamforming

DEFF Research Database (Denmark)

Song, Woo-keun; Ellermeier, Wolfgang; Minnaar, Pauli

2006-01-01

An algorithm is proposed for estimating the loudness of several simultaneous sound sources by means of microphone-array beamforming. The algorithm is derived from two listening experiments in which the loudness of two simultaneous sounds (narrow-band noises with 1-kHz and 3.15-kHz center...... frequencies) was matched to a single sound (2-kHz narrow-band noise). The simultaneous sounds were presented from either one sound source or two spatially separated sources, whereas the single sound was presented from the frontal direction. The results indicate that overall loudness can be calculated...... by summing the loudnesses of the individual sources according to a simple psychophysical relationship....

Proof-of-Work as Anonymous Micropayment: Rewarding a Tor Relay

OpenAIRE

Biryukov, Alex; Pustogarov, Ivan

2015-01-01

In this paper we propose a new micropayments scheme which can be used to reward Tor relay operators. Tor clients do not pay Tor relays with electronic cash directly but submit proof of work shares which the relays can resubmit to a crypto-currency mining pool. Relays credit users who submit shares with tickets that can later be used to purchase improved service. Both shares and tickets when sent over Tor circuits are anonymous. The analysis of the crypto-currencies market prices shows that th...

Error-rate performance analysis of opportunistic regenerative relaying

KAUST Repository

Tourki, Kamel

2011-09-01

In this paper, we investigate an opportunistic relaying scheme where the selected relay assists the source-destination (direct) communication. In our study, we consider a regenerative opportunistic relaying scheme in which the direct path can be considered unusable, and takes into account the effect of the possible erroneously detected and transmitted data at the best relay. We first derive the exact statistics of each hop, in terms of probability density function (PDF). Then, the PDFs are used to determine accurate closed form expressions for end-to-end bit-error rate (BER) of binary phase-shift keying (BPSK) modulation where the detector may use maximum ration combining (MRC) or selection combining (SC). Finally, we validate our analysis by showing that performance simulation results coincide with our analytical results over linear network (LN) architecture and considering Rayleigh fading channels. © 2011 IEEE.

An RSS based location estimation technique for cognitive relay networks

KAUST Repository

Qaraqe, Khalid A.

2010-11-01

In this paper, a received signal strength (RSS) based location estimation method is proposed for a cooperative wireless relay network where the relay is a cognitive radio. We propose a method for the considered cognitive relay network to determine the location of the source using the direct and the relayed signal at the destination. We derive the Cramer-Rao lower bound (CRLB) expressions separately for x and y coordinates of the location estimate. We analyze the effects of cognitive behaviour of the relay on the performance of the proposed method. We also discuss and quantify the reliability of the location estimate using the proposed technique if the source is not stationary. The overall performance of the proposed method is presented through simulations. ©2010 IEEE.

CERN’s annual relay a runaway success

CERN Document Server

Klaus Hanke for the CERN Running Club

2016-01-01

With a record participation of 128 teams of six runners each, this year’s CERN Relay Race took place on 19 May on the Meyrin site.   One of the many winning teams from the 2016 relay race. (Image: Sophia Bennett/CERN) With a record participation of 128 teams and 768 runners, this year’s CERN Relay Race took place on 19 May on the Meyrin site. The teams were mainly composed of CERN staff or contractors working on the CERN site.  A few external teams took also part in the race. Times ranged from 10 min 19 s to over 18 min. The Running Club website now has both the results, and the photos from race day. The CERN Relay Race is jointly organised every year by the CERN Running Club and the Staff Association. It is a tradition that is appreciated by many as a team building, rather than a competitive event. The CERN Running Club wishes to thank all runners and all volunteers for making this event a success.

Securing Relay Networks with Artificial Noise: An Error Performance-Based Approach

Directory of Open Access Journals (Sweden)

Ying Liu

2017-07-01

Full Text Available We apply the concept of artificial and controlled interference in a two-hop relay network with an untrusted relay, aiming at enhancing the wireless communication secrecy between the source and the destination node. In order to shield the square quadrature amplitude-modulated (QAM signals transmitted from the source node to the relay, the destination node designs and transmits artificial noise (AN symbols to jam the relay reception. The objective of our considered AN design is to degrade the error probability performance at the untrusted relay, for different types of channel state information (CSI at the destination. By considering perfect knowledge of the instantaneous CSI of the source-to-relay and relay-to-destination links, we first present an analytical expression for the symbol error rate (SER performance at the relay. Based on the assumption of an average power constraint at the destination node, we then derive the optimal phase and power distribution of the AN that maximizes the SER at the relay. Furthermore, we obtain the optimal AN design for the case where only statistical CSI is available at the destination node. For both cases, our study reveals that the Gaussian distribution is generally not optimal to generate AN symbols. The presented AN design takes into account practical parameters for the communication links, such as QAM signaling and maximum likelihood decoding.

Efficient incremental relaying for packet transmission over fading channels

KAUST Repository

Fareed, Muhammad Mehboob

2014-07-01

In this paper, we propose a novel relaying scheme for packet transmission over fading channels, which improves the spectral efficiency of cooperative diversity systems by utilizing limited feedback from the destination. Our scheme capitalizes on the fact that relaying is only required when direct transmission suffers deep fading. We calculate the packet error rate for the proposed efficient incremental relaying (EIR) scheme with both amplify and forward and decode and forward relaying. We compare the performance of the EIR scheme with the threshold-based incremental relaying (TIR) scheme. It is shown that the efficiency of the TIR scheme is better for lower values of the threshold. However, the efficiency of the TIR scheme for higher values of threshold is outperformed by the EIR. In addition, three new threshold-based adaptive EIR are devised to further improve the efficiency of the EIR scheme. We calculate the packet error rate and the efficiency of these new schemes to provide the analytical insight. © 2014 IEEE.

Beamforming Through Regularized Inverse Problems in Ultrasound Medical Imaging.

Science.gov (United States)

Szasz, Teodora; Basarab, Adrian; Kouame, Denis

2016-12-01

Beamforming (BF) in ultrasound (US) imaging has significant impact on the quality of the final image, controlling its resolution and contrast. Despite its low spatial resolution and contrast, delay-and-sum (DAS) is still extensively used nowadays in clinical applications, due to its real-time capabilities. The most common alternatives are minimum variance (MV) method and its variants, which overcome the drawbacks of DAS, at the cost of higher computational complexity that limits its utilization in real-time applications. In this paper, we propose to perform BF in US imaging through a regularized inverse problem based on a linear model relating the reflected echoes to the signal to be recovered. Our approach presents two major advantages: 1) its flexibility in the choice of statistical assumptions on the signal to be beamformed (Laplacian and Gaussian statistics are tested herein) and 2) its robustness to a reduced number of pulse emissions. The proposed framework is flexible and allows for choosing the right tradeoff between noise suppression and sharpness of the resulted image. We illustrate the performance of our approach on both simulated and experimental data, with in vivo examples of carotid and thyroid. Compared with DAS, MV, and two other recently published BF techniques, our method offers better spatial resolution, respectively contrast, when using Laplacian and Gaussian priors.

Relay discovery and selection for large-scale P2P streaming.

Directory of Open Access Journals (Sweden)

Chengwei Zhang

Full Text Available In peer-to-peer networks, application relays have been commonly used to provide various networking services. The service performance often improves significantly if a relay is selected appropriately based on its network location. In this paper, we studied the location-aware relay discovery and selection problem for large-scale P2P streaming networks. In these large-scale and dynamic overlays, it incurs significant communication and computation cost to discover a sufficiently large relay candidate set and further to select one relay with good performance. The network location can be measured directly or indirectly with the tradeoffs between timeliness, overhead and accuracy. Based on a measurement study and the associated error analysis, we demonstrate that indirect measurements, such as King and Internet Coordinate Systems (ICS, can only achieve a coarse estimation of peers' network location and those methods based on pure indirect measurements cannot lead to a good relay selection. We also demonstrate that there exists significant error amplification of the commonly used "best-out-of-K" selection methodology using three RTT data sets publicly available. We propose a two-phase approach to achieve efficient relay discovery and accurate relay selection. Indirect measurements are used to narrow down a small number of high-quality relay candidates and the final relay selection is refined based on direct probing. This two-phase approach enjoys an efficient implementation using the Distributed-Hash-Table (DHT. When the DHT is constructed, the node keys carry the location information and they are generated scalably using indirect measurements, such as the ICS coordinates. The relay discovery is achieved efficiently utilizing the DHT-based search. We evaluated various aspects of this DHT-based approach, including the DHT indexing procedure, key generation under peer churn and message costs.

Performance of Adaptive Antennas in FH-GSM Using Conventional Beamforming

DEFF Research Database (Denmark)

Mogensen, Preben Elgaard; Leth-Espensen, P; Zetterberg, P.

2000-01-01

This paper presents the performance of adaptive antennas in a 1/3 reuse frequency hopping GSM network using conventional beamforming. It mainly focuses on C/I improvement for the purpose of capacity enhancement. The performance evaluation has been conducted by means of network computer simulations...... implementation facilitates a potential capacity gain of x3 in a 1/3 reuse FH-GSM network for an array size of M = 4-6....

Optimal Coordination of Distance and Directional Overcurrent Relays Considering Different Network Topologies

OpenAIRE

Y. Damchi; J. Sadeh; H. Rajabi Mashhadi

2015-01-01

Most studies in relay coordination have focused solely on coordination of overcurrent relays while distance relays are used as the main protection of transmission lines. Since, simultaneous coordination of these two types of relays can provide a better protection, in this paper, a new approach is proposed for simultaneous coordination of distance and directional overcurrent relays (D&DOCRs). Also, pursued by most of the previously published studies, the settings of D&DOCRs are usually determi...

Microcomputer relay regulator in the CAMAC standard

International Nuclear Information System (INIS)

Nikolaev, V.P.

1984-01-01

The digital relay regulator is developed on the base of the KM001 microcomputer and KK06 controller for automatic control ob ects with transfer functions describing a broad class of systems using actuating motors (stabilitation, follow-up systems). The CAMAC relay-unit realizes the regulation law and provides the possibility to control analogous values by 8 channels

Coordination of Regenerative Relays and Direct Users in Wireless Cellular Networks

DEFF Research Database (Denmark)

Thai, Chan; Popovski, Petar

2011-01-01

The area of wireless cooperation/relaying has recently been significantly enriched by the ideas of wireless network coding (NC), which bring substantial gains in spectral efficiency. These gains have mainly been demonstrated in scenarios with two-way relaying. Inspired by the ideas of wireless NC......, recently we have proposed techniques for coordinated direct/relay (CDR) transmissions. These techniques embrace the interference among the communication flows to/from direct and relayed users, leveraging on the fact that the interference can be subsequently canceled. Hence, by allowing simultaneous...... transmissions, spectral efficiency is increased. In our prior work, we have considered CDR with non-regenerative relay that uses Amplify-and-Forward (AF). In this paper we consider the case of regenerative Decode-and-Forward (DF) relay. This refers also to joint decoding of the interfering flows received over...

Admission Control Threshold in Cellular Relay Networks with Power Adjustment

Directory of Open Access Journals (Sweden)

Lee Ki-Dong

2009-01-01

Full Text Available Abstract In the cellular network with relays, the mobile station can benefit from both coverage extension and capacity enhancement. However, the operation complexity increases as the number of relays grows up. Furthermore, in the cellular network with cooperative relays, it is even more complex because of an increased dimension of signal-to-noise ratios (SNRs formed in the cooperative wireless transmission links. In this paper, we propose a new method for admission capacity planning in a cellular network using a cooperative relaying mechanism called decode-and-forward. We mathematically formulate the dropping ratio using the randomness of "channel gain." With this, we formulate an admission threshold planning problem as a simple optimization problem, where we maximize the accommodation capacity (in number of connections subject to two types of constraints. (1 A constraint that the sum of the transmit powers of the source node and relay node is upper-bounded where both nodes can jointly adjust the transmit power. (2 A constraint that the dropping ratio is upper-bounded by a certain threshold value. The simplicity of the problem formulation facilitates its solution in real-time. We believe that the proposed planning method can provide an attractive guideline for dimensioning a cellular relay network with cooperative relays.

Implementation of a microcomputer based distance relay for parallel transmission lines

International Nuclear Information System (INIS)

Phadke, A.G.; Jihuang, L.

1986-01-01

Distance relaying for parallel transmission lines is a difficult application problem with conventional phase and ground distance relays. It is known that for cross-country faults involving dissimilar phases and ground, three phase tripping may result. This paper summarizes a newly developed microcomputer based relay which is capable of classifying the cross-country fault correctly. The paper describes the principle of operation and results of laboratory tests of this relay

Performance Analysis of Selective Decode-and-Forward Multinode Incremental Relaying with Maximal Ratio Combining

KAUST Repository

Hadjtaieb, Amir

2013-09-12

In this paper, we propose an incremental multinode relaying protocol with arbitrary N-relay nodes that allows an efficient use of the channel spectrum. The destination combines the received signals from the source and the relays using maximal ratio Combining (MRC). The transmission ends successfully once the accumulated signal-to-noise ratio (SNR) exceeds a predefined threshold. The number of relays participating in the transmission is adapted to the channel conditions based on the feedback from the destination. The use of incremental relaying allows obtaining a higher spectral efficiency. Moreover, the symbol error probability (SEP) performance is enhanced by using MRC at the relays. The use of MRC at the relays implies that each relay overhears the signals from the source and all previous relays and combines them using MRC. The proposed protocol differs from most of existing relaying protocol by the fact that it combines both incremental relaying and MRC at the relays for a multinode topology. Our analyses for a decode-and-forward mode show that: (i) compared to existing multinode relaying schemes, the proposed scheme can essentially achieve the same SEP performance but with less average number of time slots, (ii) compared to schemes without MRC at the relays, the proposed scheme can approximately achieve a 3 dB gain.

Spectral efficiency enhancement with interference cancellation for wireless relay network

DEFF Research Database (Denmark)

Yomo, Hiroyuki; De Carvalho, Elisabeth

The introduction of relaying into wireless communication system for coverage enhancement can cause severe decrease of spectral efficiency due to the requirement on extra radio resource. In this paper, we propose a method to increase spectral efficiency in such a wireless relay network by employing...... an interference cancellation technique. We focus on a typical scenario of relaying in a cellular system, where a mobile station (MS) requires the help of a relay station (RS) to communicate with the base station (BS). In such a case, interference cancellation can be used to achieve a small reuse distance...... of identical radio resource. We analyze a simple scenario with BS, single RS, and 2 MSs, and show that the proposed method has significant potential to enhance spectral efficiency in wireless relay networks....

Resource allocation for relay assisted cognitive radio networks

KAUST Repository

Zafar, Ammar; Alouini, Mohamed-Slim; Chen, Yunfei; Radaydeh, Redha M.

2012-01-01

transmission power and the relay transmission power. Numerical results show that the optimal sensing time is dependent on the primary user's signal-to-noise-ratio (SNR). They also show that SCR increases with increase in the number of relays. © 2012 IEEE.

Protective relaying of power systems using mathematical morphology

CERN Document Server

Wu, QH; Ji, TY

2009-01-01

Discusses the development of novel protective relaying algorithms, using Mathematical Morphology (MM). This book introduces the fundamental principles of MM, and brings together the applications of MM to develop different protective relaying algorithms for the protection of a variety of power system components.

Enhancing the beamforming map of spherical arrays at low frequencies using acoustic holography

DEFF Research Database (Denmark)

Tiana Roig, Elisabet; Torras Rosell, Antoni; Fernandez Grande, Efren

2014-01-01

Recent studies have shown that the localization of acoustic sources based on circular arrays can be improved at low frequencies by combining beamforming with acoustic holography. This paper extends this technique to the three dimensional case by making use of spherical arrays. The pressure captur...

Coded Cooperation for Multiway Relaying in Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Zhongwei Si

2015-06-01

Full Text Available Wireless sensor networks have been considered as an enabling technology for constructing smart cities. One important feature of wireless sensor networks is that the sensor nodes collaborate in some manner for communications. In this manuscript, we focus on the model of multiway relaying with full data exchange where each user wants to transmit and receive data to and from all other users in the network. We derive the capacity region for this specific model and propose a coding strategy through coset encoding. To obtain good performance with practical codes, we choose spatially-coupled LDPC (SC-LDPC codes for the coded cooperation. In particular, for the message broadcasting from the relay, we construct multi-edge-type (MET SC-LDPC codes by repeatedly applying coset encoding. Due to the capacity-achieving property of the SC-LDPC codes, we prove that the capacity region can theoretically be achieved by the proposed MET SC-LDPC codes. Numerical results with finite node degrees are provided, which show that the achievable rates approach the boundary of the capacity region in both binary erasure channels and additive white Gaussian channels.

Novel Material Integration for Reliable and Energy-Efficient NEM Relay Technology

Science.gov (United States)

Chen, I.-Ru

Energy-efficient switching devices have become ever more important with the emergence of ubiquitous computing. NEM relays are promising to complement CMOS transistors as circuit building blocks for future ultra-low-power information processing, and as such have recently attracted significant attention from the semiconductor industry and researchers. Relay technology potentially can overcome the energy efficiency limit for conventional CMOS technology due to several key characteristics, including zero OFF-state leakage, abrupt switching behavior, and potentially very low active energy consumption. However, two key issues must be addressed for relay technology to reach its full potential: surface oxide formation at the contacting surfaces leading to increased ON-state resistance after switching, and high switching voltages due to strain gradient present within the relay structure. This dissertation advances NEM relay technology by investigating solutions to both of these pressing issues. Ruthenium, whose native oxide is conductive, is proposed as the contacting material to improve relay ON-state resistance stability. Ruthenium-contact relays are fabricated after overcoming several process integration challenges, and show superior ON-state resistance stability in electrical measurements and extended device lifetime. The relay structural film is optimized via stress matching among all layers within the structure, to provide lower strain gradient (below 10E-3/microm -1) and hence lower switching voltage. These advancements in relay technology, along with the integration of a metallic interconnect layer, enable complex relay-based circuit demonstration. In addition to the experimental efforts, this dissertation theoretically analyzes the energy efficiency limit of a NEM switch, which is generally believed to be limited by the surface adhesion energy. New compact (electronic device technology.

A Stochastic Geometry Approach to Full-Duplex MIMO Relay Network

Directory of Open Access Journals (Sweden)

Mhd Nour Hindia

2018-01-01

Full Text Available Cellular networks are extensively modeled by placing the base stations on a grid, with relays and destinations being placed deterministically. These networks are idealized for not considering the interferences when evaluating the coverage/outage and capacity. Realistic models that can overcome such limitation are desirable. Specifically, in a cellular downlink environment, the full-duplex (FD relaying and destination are prone to interferences from unintended sources and relays. However, this paper considered two-hop cellular network in which the mobile nodes aid the sources by relaying the signal to the dead zone. Further, we model the locations of the sources, relays, and destination nodes as a point process on the plane and analyze the performance of two different hops in the downlink. Then, we obtain the success probability and the ergodic capacity of the two-hop MIMO relay scheme, accounting for the interference from all other adjacent cells. We deploy stochastic geometry and point process theory to rigorously analyze the two-hop scheme with/without interference cancellation. These attained expressions are amenable to numerical evaluation and are corroborated by simulation results.

Minimax robust relay selection based on uncertain long-term CSI

KAUST Repository

Nisar, Muhammad Danish

2014-02-01

Cooperative communications via multiple relay nodes is known to provide the benefits of increase diversity and coverage. Simultaneous transmission via multiple relays, however, requires strong coordination between nodes either in terms of slot-based transmission or distributed space-time (ST) code implementation. Dynamically selecting a single best relay out of multiple relays and then using it alone for cooperative transmission alleviates the need for this strong coordination while still reaping the benefits of increased diversity and coverage. In this paper, we consider the design of relay selection (RS) under an imperfect knowledge of long-term channel state information (CSI) at the relay nodes, and we pursue minimax optimization to arrive at a robust RS approach that promises the best guarantee on the worst-case end-to-end signal-to-noise ratio (SNR). We provide some intuitive examples and extensive simulation results, not only in terms of worst-case SNR performance but also in terms of average bit-error-rate (BER) performance, to demonstrate the benefits of the proposed minimax robust RS scheme. © 2013 IEEE.

Control and Protection Cooperation Strategy for Voltage Instability

DEFF Research Database (Denmark)

Liu, Zhou; Chen, Zhe; Sun, Haishun

2012-01-01

Most cascaded blackouts are caused by unexpected backup relay operations due to low voltage or overload state caused by post fault load restoration dynamics. If such state can be sensed and adjusted appropriately prior to those relay actions, system stability might be sustained. This paper proposed...... a control and protection cooperation strategy to prevent post fault voltage instability. The multi-agent technology is applied for the strategy implementation; the criteria based on wide area measured apparent impedances are defined to choose the control strategy, such as tap changer adjusting or load...

Quasi-period oscillations of relay feedback systems

International Nuclear Information System (INIS)

Wen Guilin; Wang Qingguo; Lee, T.H.

2007-01-01

This paper presents an analytical method for investigation of the existence and stability of quasi-period oscillations (torus solutions) for a class of relay feedback systems. The idea is to analyze Poincare map from one switching surface to the next based on the Hopf bifurcation theory of maps. It is shown that there exist quasi-period oscillations in certain relay feedback systems

Interference alignment for degrees of freedom improvement in 3-relay half-duplex systems

KAUST Repository

Park, Seongho

2011-12-01

In a half-duplex relaying, the capacity pre-log factor is a major drawback in spectral efficiency. This paper proposes a linear precoding scheme and an alternate relaying protocol in a dual-hop half-duplex system where three relays help the communication between the source and the destination. In our proposed scheme, we consider a phase incoherent method in relays in which the source alternately transmits message signals to the different relays. In addition, we propose a linear interference alignment scheme which can eliminate the inter-relay interference resulted from the phase incoherence of relaying. Based on our analysis of degrees of freedom and our simulation results, we show that our proposed scheme achieves additional degrees of freedom compared to the conventional half-duplex relaying. © 2011 IEEE.

Overlay cognitive radio systems with adaptive two-way relaying

KAUST Repository

Hyadi, Amal

2013-12-01

In this paper, we propose a spectrum sharing mechanism with a two-phase two-way relaying protocol for an overlay cognitive network. The system comprises two primary users (PUs) and two secondary users (SUs). One of the SUs acts as a relay for the PUs and gains spectrum sharing as long as he respects outage probability constraints of the primary system. Moreover, we consider that the relaying node performs an optimal power allocation scheme that minimizes the outage performance of the secondary receiver. Closed form expressions for the outage probability are derived for the cases of Decode-and-Forward (DF), Amplify-and-Forward (AF), and adaptive relaying. Numerical simulations are presented to illustrate and compare the obtained results. © 2013 IEEE.

Near-field self-interference cancellation and quality of service multicast beamforming in full-duplex

Science.gov (United States)

Wu, Fei; Shao, Shihai; Tang, Youxi

2016-10-01

To enable simultaneous multicast downlink transmit and receive operations on the same frequency band, also known as full-duplex links between an access point and mobile users. The problem of minimizing the total power of multicast transmit beamforming is considered from the viewpoint of ensuring the suppression amount of near-field line-of-sight self-interference and guaranteeing prescribed minimum signal-to-interference-plus-noise-ratio (SINR) at each receiver of the multicast groups. Based on earlier results for multicast groups beamforming, the joint problem is easily shown to be NP-hard. A semidefinite relaxation (SDR) technique with linear program power adjust method is proposed to solve the NP-hard problem. Simulation shows that the proposed method is feasible even when the local receive antenna in nearfield and the mobile user in far-filed are in the same direction.

Amplitude death induced by mixed attractive and repulsive coupling in the relay system

Science.gov (United States)

Zhao, Nannan; Sun, Zhongkui; Xu, Wei

2018-01-01

The amplitude death (AD) phenomenon is found in the relay system in the presence of the mixed couplings composed of attractive coupling and repulsive coupling. The generation mechanism of AD is revealed and shows that the middle oscillator achieving AD is a prerequisite to further suppress oscillation of the outermost oscillators for the paradigmatic Stuart-Landau and Rössler models. Moreover, regarding the Stuart-Landau relay system as a small motif of star network, we also observe that the mixed couplings can facilitate AD state of the whole network system. Particularly, the threshold of coupling strength is invariable with the change of network size. Our findings may shed a new insight to explore the effects of hybrid coupling on complex systems, also provide a new strategy to control dynamic behaviors in engineering science and neuroscience fields.

Best relay selection using SNR and interference quotient for underlay cognitive networks

KAUST Repository

Hussain, Syed Imtiaz

2012-06-01

Cognitive networks in underlay settings operate simultaneously with the primary networks satisfying stringent interference limits. This condition forces them to operate with low transmission powers and confines their area of coverage. In an effort to reach remote destinations, underlay cognitive sources make use of relaying techniques. Selecting the best relay among those who are ready to cooperate is different in underlay settings than traditional non-cognitive networks. In this paper, we present a relay selection scheme which uses the quotient of the relay link signal to noise ratio (SNR) and the interference generated from the relay to the primary user to choose the best relay. The proposed scheme optimizes this quotient in a way to maximize the relay link SNR above a certain value whereas the interference is kept below a defined threshold. We derive closed expressions for the outage probability and bit error probability of the system incorporating this scheme. Simulation results confirm the validity of the analytical results and reveal that the relay selection in cognitive environment is feasible in low SNR regions. © 2012 IEEE.

Virtual MIMO Beamforming and Device Pairing Enabled by Device-to-Device Communications for Multidevice Networks

Directory of Open Access Journals (Sweden)

Yeonjin Jeong

2017-01-01

Full Text Available We consider a multidevice network with asymmetric antenna configurations which supports not only communications between an access point and devices but also device-to-device (D2D communications for the Internet of things. For the network, we propose the transmit and receive beamforming with the channel state information (CSI for virtual multiple-input multiple-output (MIMO enabled by D2D receive cooperation. We analyze the sum rate achieved by a device pair in the proposed method and identify the strategies to improve the sum rate of the device pair. We next present a distributed algorithm and its equivalent algorithm for device pairing to maximize the throughput of the multidevice network. Simulation results confirm the advantages of the transmit CSI and D2D cooperation as well as the validity of the distributive algorithm.

Adaptive transmission based on multi-relay selection and rate-compatible LDPC codes

Science.gov (United States)

Su, Hualing; He, Yucheng; Zhou, Lin

2017-08-01

In order to adapt to the dynamical changeable channel condition and improve the transmissive reliability of the system, a cooperation system of rate-compatible low density parity check (RC-LDPC) codes combining with multi-relay selection protocol is proposed. In traditional relay selection protocol, only the channel state information (CSI) of source-relay and the CSI of relay-destination has been considered. The multi-relay selection protocol proposed by this paper takes the CSI between relays into extra account in order to obtain more chances of collabration. Additionally, the idea of hybrid automatic request retransmission (HARQ) and rate-compatible are introduced. Simulation results show that the transmissive reliability of the system can be significantly improved by the proposed protocol.

High Resolution Ultrasound Imaging Using Adaptive Beamforming with Reduced Number of Active Elements

DEFF Research Database (Denmark)

Holfort, Iben Kraglund; Gran, Fredrik; Jensen, Jørgen Arendt

2009-01-01

is proposed. By reducing the number of active sensor elements, an increased resolution can be obtained with the MV beamformer. This observation is directly opposite the well-known relation between the spatial extent of the aperture and the achievable resolution. The investigations are based on Field II...

Frame Allocation and Scheduling for Relay Networks in the LTE Advanced Standard

OpenAIRE