WorldWideScience

Sample records for relative electrochemical behavior

  1. Mass transfer behavior of rotating square cylinder electrochemical reactor in relation to wastewater treatment

    International Nuclear Information System (INIS)

    Abdel-Aziz, M.S.M.; El-Shazly, A.H.; Farag, H.A.; Sedahmed, G.H.

    2011-01-01

    Highlights: → The work explores a new electrochemical reactor by using square rotating cylinders. → The results show that it is superior to the traditional circular rotating cylinder. → A dimensionless design equation for the new reactor was correlated. → The oxalic acid removal by the new reactor was succeeded and found promising. → The energy consumption per kg oxalic acid removed by the unit was calculated. - Abstract: Rates of mass transfer at a rotating square cylinder were measured by an electrochemical technique which involved measuring the limiting current of the cathodic reduction of K 3 Fe(CN) 6 in a large excess of NaOH solution. Variables studied were: cylinder rotation speed, physical properties of the solution and cylinder equivalent diameter. The data for the condition 1577 0.33 Re 0.45 For a given set of conditions the rate of mass transfer at the square rotating cylinder was found to be higher than that at the traditional circular rotating cylinder by an amount ranging from 47% to 200% depending on Re. The use of the square rotating cylinder electrode in removing oxalic acid from wastewater by anodic oxidation on Pb/PbO anode was examined and found to be promising.

  2. Contribution to the Study of the Relation between Microstructure and Electrochemical Behavior of Iron-Based FeCoC Ternary Alloys

    Directory of Open Access Journals (Sweden)

    Farida Benhalla-Haddad

    2012-01-01

    Full Text Available This work deals with the relation between microstructure and electrochemical behavior of four iron-based FeCoC ternary alloys. First, the arc-melted studied alloys were characterized using differential thermal analyses and scanning electron microscopy. The established solidification sequences of these alloys show the presence of two primary crystallization phases (δ(Fe and graphite as well as two univariante lines : peritectic L+(Fe↔(Fe and eutectic L↔(Fe+Cgraphite. The ternary alloys were thereafter studied in nondeaerated solution of 10−3 M NaHCO3 + 10−3 M Na2SO4, at 25°C, by means of the potentiodynamic technique. The results indicate that the corrosion resistance of the FeCoC alloys depends on the carbon amount and the morphology of the phases present in the studied alloys.

  3. The behavior of electrochemical cell resistance

    International Nuclear Information System (INIS)

    Ritley, K.A.; Dull, P.M.; Weber, M.H.; Carroll, M.; Hurst, J.J.; Lynn, K.G.

    1990-01-01

    Knowledge of the basic electrochemical behavior found in typical cold fusion experiments is important to understanding and preventing experimental errors. For a Pd/LiOH(D)/Pt electrochemical cell, the applied cell voltage/current relationship (the effective cell resistance) does not obey Ohm's law directly, but instead exhibits a complicated response to the current, voltage, temperature, electrolyte conductance, and other factors. Failure to properly consider this response can possibly result in errors that could affect the heat balance in calorimetry and temperature measurement experiments. Measurements of this response under varying voltage, temperature, and electrolyte conductivity conditions are reported. A plausible scenario in which the temperature dependence of the effective cell resistance can either exaggerate or ameliorate novel exothermic processes is suggested

  4. Electrochemical behavior of monolayer and bilayer graphene.

    Science.gov (United States)

    Valota, Anna T; Kinloch, Ian A; Novoselov, Kostya S; Casiraghi, Cinzia; Eckmann, Axel; Hill, Ernie W; Dryfe, Robert A W

    2011-11-22

    Results of a study on the electrochemical properties of exfoliated single and multilayer graphene flakes are presented. Graphene flakes were deposited on silicon/silicon oxide wafers to enable fast and accurate characterization by optical microscopy and Raman spectroscopy. Conductive silver paint and silver wires were used to fabricate contacts; epoxy resin was employed as a masking coating in order to expose a stable, well-defined area of graphene. Both multilayer and monolayer graphene microelectrodes showed quasi-reversible behavior during voltammetric measurements in potassium ferricyanide. However, the standard heterogeneous charge transfer rate constant, k°, was estimated to be higher for monolayer graphene flakes. © 2011 American Chemical Society

  5. Study of the electrochemical behavior of the niobium in relation to the hydrogen cyclical charge and uncharge; Estudo do comportamento eletroquimico do niobio em relacao ao carregamento e descarregamento ciclicos de hidrogenio

    Energy Technology Data Exchange (ETDEWEB)

    Silva, A.G.S.G. da; Ponte, H.A.; Pashchuk, A. [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil). Centro Politecnico. Lab. de Eletroquimica de Superficie e Corrosao (LESK)], e-mail: aleksantos@hotmail.com

    2006-07-01

    One of the greatest problems found in the oil industry is the control of the deterioration at the steels structures of the units that compose the process petroleum refine. This deterioration is related the mechanisms involving processes of hydrogen embrittlement. The work had as objective to study the electrochemical behavior of the niobium (Nb) with relation to the charging and uncharging of hydrogen, to evaluate the potential to use of the Nb in the construction of electrochemical hydrogen probes. For this study techniques of cronopotenciometry and potential of open circuit (OCP) for the pure Nb submitted the different hydrogen charging conditions had been used. The gotten partial results indicate the viability to use of the niobium as hydrogen probe, however, it is necessary one better understanding of the mechanisms of hydrogen interaction with the niobium. (author)

  6. Electrochemical Behavior of Biologically Important Indole Derivatives

    Directory of Open Access Journals (Sweden)

    Cigdem Karaaslan

    2011-01-01

    Full Text Available Voltammetric techniques are most suitable to investigate the redox properties of a new drug. Use of electrochemistry is an important approach in drug discovery and research as well as quality control, drug stability, and determination of physiological activity. The indole nucleus is an essential element of a number of natural and synthetic products with significant biological activity. Indole derivatives are the well-known electroactive compounds that are readily oxidized at carbon-based electrodes, and thus analytical procedures, such as electrochemical detection and voltammetry, have been developed for the determination of biologically important indoles. This paper explains some of the relevant and recent achievements in the electrochemistry processes and parameters mainly related to biologically important indole derivatives in view of drug discovery and analysis.

  7. Evaluation of the electrochemical behavior of U2.5Zr7.5Nb and U3Zr9Nb uranium alloys in relation to the pH and the solution aeration

    International Nuclear Information System (INIS)

    Mansur, Fabio Abud; Santos, Ana Maria Matildes dos; Ferraz, Wilmar Barbosa; Figueiredo, Celia de Araujo

    2011-01-01

    The Centro de Desenvolvimento da Tecnologia Nuclear (CDTN) is developing, in cooperation with the Centro Tecnologico da Marinha (CTMSP), the advanced nuclear plate type fuel for the second core of the land-based reactor prototype of the Laboratorio de Geracao Nucleo-Eletrica (LABGENE). Recent investigations have shown that the fuel made of uranium-based niobium and zirconium alloys reaches the best performance relative to other fuels, e.g. UO 2 . Niobium and Zirconium also increase the corrosion resistance and the mechanical strength of the uranium alloys. By means of electrochemical techniques the corrosion behavior of alloys U 2 . 5 Zr 7.5 Nb and U 3 Zr 9 Nb, developed at CDTN and heat treated in the temperature range of 200 deg C to 600 deg C, was assessed. The effect of the parameters pH and solution aeration was studied as well as the influence of zirconium and niobium alloying elements in the corrosion of uranium. The techniques used were open circuit potential, electrochemical impedance and potentiodynamic anodic polarization at room temperature. The tests were performed in a three-electrode electrochemical cell with Ag/AgCl (3M KCl) as the reference electrode and a platinum plate as the auxiliary electrode. The potentiodynamic polarization curves of uranium and its alloys in acidic solutions showed regions with anodic currents limited by a passive film. The presence of niobium and zirconium contributed for the formation of this film. The impedance data showed the presence of two semicircles in the Bode diagram, indicating the occurrence of two distinct electrochemical processes. The data were fitted to an equivalent circuit model in order to obtain parameters of the electrochemical processes and evaluate the effect of the studied variables. (author)

  8. Electrochemical behavior of titanium implanted with platinum

    International Nuclear Information System (INIS)

    Thompson, N.G.; Lichter, B.D.; Appleton, B.R.; Kelly, E.J.; White, C.W.

    1979-01-01

    The following conclusions apply to Ti(Pt) near-surface alloys studied. (1) Open-circuit corrosion measurements show that accumulation of platinum may occur at a surface concentration of 0.32 atomic percent Pt while no accumulation occurs at 0.16 atomic percent Pt. However, these results do not allow a distinction as to cause of accumulation to be made between concentration effects and effects due to the presence of an oxide film. (2) Potentiostatic corrosion at -0.450 V (active corrosion) establish that little or no accumulation of platinum occurs at an oxide-free surface for concentrations less than 0.086 atomic percent Pt; whereas, a large amount of accumulation occurs for a distribution with a peak concentration of 0.83 atomic percent Pt. (3) An initial distribution having a peak concentration of 0.32 atomic percent platinum is sufficient to induce natural passivity in titanium and bring a freely corroding sample to a potential of 0.269 V. This is nearly the applicable reversible potential (-0.260 V) for the hydrogen reaction in 1N H 2 SO 4 . (4) Of three samples which showed accumulation, platinum was eventually lost for two of these samples (0.32 atomic percent, open-circuit corrosion; 0.83 atomic percent, potentiostatic corrosion). The remaining sample (9.1 atomic percent, open-circuit corrosion) maintained the maximum possible potential of -0.260 V for the length of the experiment (approx. 30 days). (5) For samples which had been polarized at -0.300 to -0.340 V and which had eventually reverted to the behavior of pure Ti, post corrosion RBS measurements reveal that a substantial fraction of the Pt fluence is retained on the surface in an electrochemically inactive state

  9. Electrochemical behavior of some new pyrimidine derivatives

    Directory of Open Access Journals (Sweden)

    MUSTAFA LUTFU BERKEM

    2004-09-01

    Full Text Available Electrochemical reduction of two recently synthesized pyrimidine compounds, 1-amino-5-benzoyil-4-phenyl-1H-pyrimidine-2-one (I, and 1-amino-5-benzoil-4-phenyl-1H-pyrimidine-2-thione (II were investigated by cyclic volatmmetry at a hanging mercury drop electrode in aqueous methanol (36 % v/v and in non-aqueous methanol. A series of cathodic peaks without the corresponding anodic peaks were observed for I. As the pH of the solution was increased, some of the cathodic peaks overlapped resulting in the loss of the previously observed peaks. For II, three cathodic peaks and one anodic peak were observed in addition to those observed for I. The peak potentials shifted in the negative direction with increasing pH. This shift was measured over a large pH range (1.80 – 12.30 to determine the pKa values of the compounds. The acidity constants related to the amino groups were 4.80 and 9.80 for I and 5.50 and 9.80 for II. A thiol-thione tautomerization was observed for II, which was more pronounced in the non-aqueous methanol medium. The pK values for both protonation and deprotonation of the thiocarbonyl group were also determined. The pK values were 5.80 and 9.80 for protonation and deprotonation in aqueous methanol and 6.80 and 10.80 in non-aqueous methanol.

  10. Electrochemical corrosion behavior of carbon steel with bulk coating holidays

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    With epoxy coal tar as the coating material, the electrochemical corrosion behavior of Q235 with different kinds of bulk coating holidays has been investigated with EIS (Electrochemical Impedance Spectroscopy) in a 3.5vol% NaCl aqueous solution.The area ratio of bulk coating holiday to total coating area of steel is 4.91%. The experimental results showed that at free corrosionpotential, the corrosion of carbon steel with disbonded coating holiday is heavier than that with broken holiday and disbonded & broken holiday with time; Moreover, the effectiveness of Cathodic Protection (CP) of carbon steel with broken holiday is better than that with disbonded holiday and disbonded & broken holiday on CP potential -850 mV (vs CSE). Further analysis indicated that the two main reasons for corrosion are electrolyte solution slowly penetrating the coating, and crevice corrosion at steel/coating interface near holidays. The ratio of impedance amplitude (Z) of different frequency to minimum frequency is defined as K value. The change rate of K with frequency is related to the type of coating holiday.

  11. Electrochemical Behavior and Antioxidant and Prooxidant Activity of Natural Phenolics

    Directory of Open Access Journals (Sweden)

    Marija Todorović

    2007-10-01

    Full Text Available We have investigated the electrochemical oxidation of a number natural phenolics (salicylic acid, m-hydroxybenzoic acid, p-hydroxybenzoic acid, protocatechuic acid, o-coumaric acid, m-coumaric acid, p-coumaric acid, caffeic acid, quercetin and rutin using cyclic voltammetry. The antioxidant properties of these compounds were also studied. A structural analysis of the tested phenolics suggests that multiple OH substitution and conjugation are important determinants of the free radical scavenging activity and electrochemical behavior. Compounds with low oxidation potentials (Epa lower than 0.45 showed antioxidant activity, whereas compounds with high Epa values (>0.45 act as prooxidants.

  12. Electrochemical behavior of rare earth metals and their nitrides

    International Nuclear Information System (INIS)

    Ito, Yasuhiko; Goto, Takuya

    2004-01-01

    Pyrometallurgical recycle process using molten salts is considered to be a high potential in pyro-reprocess technologies for spent nitride fuels, and it is important to understand chemical and electro-chemical behavior of nitrides and metals in molten salts. In this study, cadmium nitrates deposited on the anode Cd plate in motlen salt (LiCl-KCl) with addition of Li 3 N are examined. The cadmium nitrates deposited have various compositions corresponding to polarization potentials and then, the relationship between the deposition potential of nitride Cd and their composition is cleared. Their standard chemical potential of CdN is estimated from electrochemical measurement. And then, potential-pH 3- diagram is drawn by voltametry examination of nitride resolution behavior with using thermochemical data of nitrides. (A. Hishinuma)

  13. Electrochemical behavior of pitch-based activated carbon fibers for electrochemical capacitors

    International Nuclear Information System (INIS)

    Lee, Hye-Min; Kwac, Lee-Ku; An, Kay-Hyeok; Park, Soo-Jin; Kim, Byung-Joo

    2016-01-01

    Highlights: • Electrode materials for electrochemical capacitors were developed using pitch-based activated carbon fibers with steam activation. • Activated carbon fibers showed enhanced specific surface area from 1520 to 3230 m 2 /g. • The increase in the specific capacitance of the samples was determined by charged pore structure during charging and discharging. - Abstract: In the present study, electrode materials for electrochemical capacitors were developed using pitch-based activated carbon fibers with steam activation. The surface and structural characteristics of activated carbon fibers were observed using scanning electron microscopy and X-ray diffraction, respectively. Pore characteristics were investigated using N 2 /77 K adsorption isotherms. The activated carbon fibers were applied as electrodes for electrical double-layer capacitors and analyzed in relation to the activation time. The specific surface area and total pore volume of the activated carbon fibers were determined to be 1520–3230 m 2 /g and 0.61–1.87 cm 3 /g, respectively. In addition, when the electrochemical characteristics were analyzed, the specific capacitance was confirmed to have increased from 1.1 F/g to 22.5 F/g. From these results, it is clear that the pore characteristics of pitch-based activated carbon fibers changed considerably in relation to steam activation and charge/discharge cycle; therefore, it was possible to improve the electrochemical characteristics of the activated carbon fibers.

  14. Electrochemical behavior of phytochelatins and related peptides at the hanging mercury drop electrode in the presence of cobalt(II) ions.

    Science.gov (United States)

    Dorcák, Vlastimil; Sestáková, Ivana

    2006-01-01

    Direct current voltammetry and differential pulse voltammetry have been used to investigate the electrochemical behaviour of two phytochelatins: heptapeptide (gamma-Glu-Cys)3-Gly and pentapeptide (gamma-Glu-Cys)2-Gly, tripeptide glutathione gamma-Glu-Cys-Gly and its fragments: dipeptides Cys-Gly and gamma-Glu-Cys at the hanging mercury drop electrode in the presence of cobalt(II) ions. Most interesting results were obtained with direct current voltammetry in the potential region of -0.80 V up to -1.80 V. Differential pulse voltammetry of the same solutions of Co(II) with peptides gives more complicated voltammograms with overlapping peaks, probably in connection with the influence of adsorption at slow scan rates necessarily used in this method. However, in using Brdicka catalytic currents for analytical purposes, differential pulse voltammograms seem to be more helpful. Presented investigations have shown that particularly the prewave of cobalt(II) allows distinguishing among phytochelatins, glutathione, and its fragments.

  15. Disease-Related Detection with Electrochemical Biosensors: A Review

    Directory of Open Access Journals (Sweden)

    Ying Huang

    2017-10-01

    Full Text Available Rapid diagnosis of diseases at their initial stage is critical for effective clinical outcomes and promotes general public health. Classical in vitro diagnostics require centralized laboratories, tedious work and large, expensive devices. In recent years, numerous electrochemical biosensors have been developed and proposed for detection of various diseases based on specific biomarkers taking advantage of their features, including sensitivity, selectivity, low cost and rapid response. This article reviews research trends in disease-related detection with electrochemical biosensors. Focus has been placed on the immobilization mechanism of electrochemical biosensors, and the techniques and materials used for the fabrication of biosensors are introduced in details. Various biomolecules used for different diseases have been listed. Besides, the advances and challenges of using electrochemical biosensors for disease-related applications are discussed.

  16. Disease-Related Detection with Electrochemical Biosensors: A Review.

    Science.gov (United States)

    Huang, Ying; Xu, Jin; Liu, Junjie; Wang, Xiangyang; Chen, Bin

    2017-10-17

    Rapid diagnosis of diseases at their initial stage is critical for effective clinical outcomes and promotes general public health. Classical in vitro diagnostics require centralized laboratories, tedious work and large, expensive devices. In recent years, numerous electrochemical biosensors have been developed and proposed for detection of various diseases based on specific biomarkers taking advantage of their features, including sensitivity, selectivity, low cost and rapid response. This article reviews research trends in disease-related detection with electrochemical biosensors. Focus has been placed on the immobilization mechanism of electrochemical biosensors, and the techniques and materials used for the fabrication of biosensors are introduced in details. Various biomolecules used for different diseases have been listed. Besides, the advances and challenges of using electrochemical biosensors for disease-related applications are discussed.

  17. Electrochemical behavior of labetalol at an ionic liquid modified carbon paste electrode and its electrochemical determination

    Directory of Open Access Journals (Sweden)

    Zhang Yan-Mei

    2013-01-01

    Full Text Available Electrochemical behavior of labetalol (LBT at carbon paste electrode (CPE and an ionic liquid1-benzyl-3-methylimidazolehexafluorophosphate([BnMIM]PF6modified carbon paste electrode([BnMIM]PF6/CPEin Britton-Robinson buffer solution (pH 2.0 was investigated by cyclic voltammetry (CV and square wave voltammetric (SWV. The experimental results showed that LBT at both the bare CPE and [BnMIM]PF6/CPEshowed an irreversible oxidation process, but at [BnMIM]PF6/CPE its oxidation peak current increased greatly and the oxidation peak potential shifted negatively. The electrode reaction process is a diffusion-controlled process involving one electron transferring accompanied by a participation of one proton at [BnMIM]PF6/CPE. At the same time, the electrochemical kinetic parameters were determined. Under the optimized electrochemical experimental conditions, the oxidation peak currents were proportional to LBT concentration in the range of 7.0 x 10-6-1.0 x 10-4 mol L-1 with the limit of detection(LOD, S/N=3 of 4.810 x 10-8 mol L-1and the limit of quantification(LOQ, S/N=10 of 1.60 x 10-7 mol L-1, respectively. The proposed method was successfully applied in the determination of LBT content in commercial tablet samples.

  18. Electrochemical corrosion behavior of gas atomized Al–Ni alloy powders

    International Nuclear Information System (INIS)

    Osório, Wislei R.; Spinelli, José E.; Afonso, Conrado R.M.; Peixoto, Leandro C.; Garcia, Amauri

    2012-01-01

    Highlights: ► Spray-formed Al–Ni alloy powders have cellular microstructures. ► Porosity has no deleterious effect on the electrochemical corrosion behavior. ► Better pitting corrosion resistance is related to a fine powder microstructure. ► A coarse microstructure can be related to better general corrosion resistance. - Abstract: This is a study describing the effects of microstructure features of spray-formed Al–Ni alloy powders on the electrochemical corrosion resistance. Two different spray-formed powders were produced using nitrogen (N 2 ) gas flow (4 and 8 bar were used). Electrochemical impedance spectroscopy (EIS), potentiodynamic anodic polarization techniques and an equivalent circuit analysis were used to evaluate the electrochemical behavior in a dilute 0.05 M NaCl solution at room temperature. It was found that a N 2 gas pressure of 8 bar resulted in a microstructure characterized by a high fraction of small powders and fine cell spacings, having improved pitting potential but higher corrosion current density when compared with the corresponding results of a coarser microstructure array obtained under a lower pressure. A favorable effect in terms of current density and oxide protective film formation was shown to be associated with the coarser microstructure, however, its pitting potential was found to be lower than that of the finer microstructure.

  19. Electrochemical fabrication and electronic behavior of polypyrrole nano-fiber array devices

    International Nuclear Information System (INIS)

    Liu Ling; Zhao Yaomin; Jia Nengqin; Zhou Qin; Zhao Chongjun; Yan Manming; Jiang Zhiyu

    2006-01-01

    Electrochemically active Polypyrrole (PPy) nano-fiber array device was fabricated via electrochemical deposition method using aluminum anodic oxide (AAO) membrane as template. After alkaline treatment electrochemically active PPy nano-fiber lost electrochemical activity, and became electrochemically inactive PPy. The electronic properties of PPy nano-fiber array devices were measured by means of a simple method. It was found that for an indium-tin oxide/electrochemically inactive PPy nano-fiber device, the conductivity of nano-fiber increased with the increase of voltage applied on the two terminals of nano-fiber. The electrochemical inactive PPy nano-fiber might be used as a nano-fiber switching diode. Both Au/electrochemically active PPy and Au/electrochemically inactive PPy nano-fiber devices demonstrate rectifying behavior, and might have been used for further application as nano-rectifiers

  20. Electrochemical fabrication and electronic behavior of polypyrrole nano-fiber array devices

    Energy Technology Data Exchange (ETDEWEB)

    Ling, Liu [Department of Chemistry, and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China); Yaomin, Zhao [Department of Chemistry, and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China); Nengqin, Jia [Department of Chemistry, and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China); Qin, Zhou [Department of Chemistry, and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China); Chongjun, Zhao [Photon Craft Project, Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences and Japan Science and Technology Agency, Shanghai 201800 (China); Manming, Yan [Department of Chemistry, and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China); Zhiyu, Jiang [Department of Chemistry, and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Fudan University, Shanghai 200433 (China)

    2006-05-01

    Electrochemically active Polypyrrole (PPy) nano-fiber array device was fabricated via electrochemical deposition method using aluminum anodic oxide (AAO) membrane as template. After alkaline treatment electrochemically active PPy nano-fiber lost electrochemical activity, and became electrochemically inactive PPy. The electronic properties of PPy nano-fiber array devices were measured by means of a simple method. It was found that for an indium-tin oxide/electrochemically inactive PPy nano-fiber device, the conductivity of nano-fiber increased with the increase of voltage applied on the two terminals of nano-fiber. The electrochemical inactive PPy nano-fiber might be used as a nano-fiber switching diode. Both Au/electrochemically active PPy and Au/electrochemically inactive PPy nano-fiber devices demonstrate rectifying behavior, and might have been used for further application as nano-rectifiers.

  1. Preliminary results of the comparison of the electrochemical behavior of a thioether and biphenyl

    Science.gov (United States)

    Morales, W.; Jones, W. R.

    1983-01-01

    An electrochemical cell was constructed to explore the feasibility of using electrochemical techniques to simulate the tribochemistry of various substances. The electrochemical cell was used to study and compare the behavior of a thioether 1,3-bis(phenylthio) benzene and biphenyl. It is found that under controlled conditions biphenyl undergoes a reversible reduction to a radical anion whereas the thioether undergoes an irreversible reduction yielding several products. The results are discussed in relationship to boundary lubrication.

  2. Hardness and electrochemical behavior of ceramic coatings on Inconel

    Directory of Open Access Journals (Sweden)

    C. SUJAYA

    2012-03-01

    Full Text Available Thin films of ceramic materials like alumina and silicon carbide are deposited on Inconel substrate by pulsed laser deposition technique using Q-switched Nd: YAG laser. Deposited films are characterized using UV-visible spectrophotometry and X-ray diffraction. Composite microhardness of ceramic coated Inconel system is measured using Knoop indenter and its film hardness is separated using a mathematical model based on area-law of mixture. It is then compared with values obtained using nanoindentation method. Film hardness of the ceramic coating is found to be high compared to the substrates. Corrosion behavior of substrates after ceramic coating is studied in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy measurements. The Nyquist and the Bode plots obtained from the EIS data are fitted by appropriate equivalent circuits. The pore resistance, the charge transfer resistance, the coating capacitance and the double layer capacitance of the coatings are obtained from the equivalent circuit. Experimental results show an increase in corrosion resistance of Inconel after ceramic coating. Alumina coated Inconel showed higher corrosion resistance than silicon carbide coated Inconel. After the corrosion testing, the surface topography of the uncoated and the coated systems are examined by scanning electron microscopy.

  3. Evaluation of the electrochemical behavior of U{sub 2.5}Zr{sub 7.5}Nb and U{sub 3}Zr{sub 9}Nb uranium alloys in relation to the pH and the solution aeration

    Energy Technology Data Exchange (ETDEWEB)

    Mansur, Fabio Abud; Santos, Ana Maria Matildes dos; Ferraz, Wilmar Barbosa; Figueiredo, Celia de Araujo, E-mail: ferraz@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    The Centro de Desenvolvimento da Tecnologia Nuclear (CDTN) is developing, in cooperation with the Centro Tecnologico da Marinha (CTMSP), the advanced nuclear plate type fuel for the second core of the land-based reactor prototype of the Laboratorio de Geracao Nucleo-Eletrica (LABGENE). Recent investigations have shown that the fuel made of uranium-based niobium and zirconium alloys reaches the best performance relative to other fuels, e.g. UO{sub 2}. Niobium and Zirconium also increase the corrosion resistance and the mechanical strength of the uranium alloys. By means of electrochemical techniques the corrosion behavior of alloys U{sub 2}.{sub 5}Zr{sub 7.5}Nb and U{sub 3}Zr{sub 9}Nb, developed at CDTN and heat treated in the temperature range of 200 deg C to 600 deg C, was assessed. The effect of the parameters pH and solution aeration was studied as well as the influence of zirconium and niobium alloying elements in the corrosion of uranium. The techniques used were open circuit potential, electrochemical impedance and potentiodynamic anodic polarization at room temperature. The tests were performed in a three-electrode electrochemical cell with Ag/AgCl (3M KCl) as the reference electrode and a platinum plate as the auxiliary electrode. The potentiodynamic polarization curves of uranium and its alloys in acidic solutions showed regions with anodic currents limited by a passive film. The presence of niobium and zirconium contributed for the formation of this film. The impedance data showed the presence of two semicircles in the Bode diagram, indicating the occurrence of two distinct electrochemical processes. The data were fitted to an equivalent circuit model in order to obtain parameters of the electrochemical processes and evaluate the effect of the studied variables. (author)

  4. Electrochemical behavior of uranyl in anhydrous polar organic media

    Energy Technology Data Exchange (ETDEWEB)

    Burn, Adam G.; Nash, Kenneth L. [Washington State Univ., Pullmann, WA (United States). Dept. of Chemistry

    2017-09-01

    Weak complexes between pentavalent and hexavalent actinyl cations have been reported to exist in acidic, non-complexing high ionic strength aqueous media. Such ''cation-cation complexes'' were first identified in the context of actinide-actinide redox reactions in acidic aqueous media relevant to solvent extraction-based separation systems, hence their characterization is of potential interest for advanced nuclear fuel reprocessing. This chemistry could be relevant to efforts to develop advanced actinide separations based on the upper oxidation states of americium, which are of current interest. In the present study, the chemical behavior of pentavalent uranyl was examined in non-aqueous, aprotic polar organic solvents (propylene carbonate and acetonitrile) to determine whether UO{sub 2}{sup +} cations generated at the reducing working electrode surface would interact with the UO{sub 2}{sup 2+} cations in the bulk phase to form cation-cation complexes in such media. In magnesium perchlorate media, the electrolyte adsorbed onto the working electrode surface and interfered with the uranyl reduction/diffusion process through an ECE (electron transfer/chemical reaction/electron transfer) mechanism. In parallel studies of uranyl redox behavior in tetrabutylammonium hexafluorophosphate solutions, an EC (electron transfer/chemical reaction) mechanism was observed in the cyclic voltammograms. Ultimately, no conclusive electrochemical evidence demonstrated uranyl cation-cation interactions in the non-aqueous, aprotic polar organic solvent solutions, though the results reported do not completely rule out the presence of UO{sub 2}{sup +}.UO{sub 2}{sup 2+} complexes.

  5. Electrokinetic and electrochemical corrosion studies related to crud formation

    International Nuclear Information System (INIS)

    Scenini, Fabio; Palumbo, Gaetano; Stevens, Nicholas; Cook, Tony; Banks, Andrew

    2012-09-01

    A potentially important mechanism for the flow-induced deposition of CRUD from pressurised high temperature primary water is the effect of 'streaming potentials' that develop across the electrochemical double layer of a metallic surface as a result of fluid flow across a pressure gradient or orifice. Thus, under such conditions, streaming currents develop normal to a surface and may result in preferential oxidation, for example of dissolved ferrous to ferric ions with their subsequent deposition as an oxide. The approach presented in this paper was to consider the electrokinetic problem is to firstly consider the magnitude of currents that can be developed under a given set of flow/mass transport conditions and, secondly, to consider the way in which these relatively small currents might give rise to oxide deposition. Electrochemical measurements on 304L samples were carried out over a range of temperatures in hydrogenated, alkaline water. The test conditions were chosen in order to simulate PWR primary water conditions. Furthermore, in order to facilitate the electrochemical studies, the ferrous ion concentration in the solution was also enhanced by the presence of a mild steel plate left in the autoclave to corrode. By employing the cyclic voltammetry technique interpreted using the Randles-Sevcik equation it was possible to calculate the concentration of ferrous ions and their diffusion coefficient. A miniature flow cell was designed for the purpose of creating regions of accelerated flow with consequent formation of anodic and cathodic regions so as to be able to measure the streaming currents. A study was carried out in order to better understand the potential which is associated with the streaming potential as function of the velocity and temperature at fixed pH. (authors)

  6. Electrochemical Behavior of Quinoxalin-2-one Derivatives at Mercury Electrodes and Its Analytical Use

    OpenAIRE

    Zimpl, Milan; Skopalova, Jana; Jirovsky, David; Bartak, Petr; Navratil, Tomas; Sedonikova, Jana; Kotoucek, Milan

    2012-01-01

    Derivatives of quinoxalin-2-one are interesting compounds with potential pharmacological activity. From this point of view, understanding of their electrochemical behavior is of great importance. In the present paper, a mechanism of electrochemical reduction of quinoxalin-2-one derivatives at mercury dropping electrode was proposed. Pyrazine ring was found to be the main electroactive center undergoing a pH-dependent two-electron reduction process. The molecule protonization of nitrogen in th...

  7. Electrochemical behavior of amorphous metal-silicon-carbon nanocomposites based on titanium or tungsten nanophase

    International Nuclear Information System (INIS)

    Pleskov, Yu.V.; Krotova, M.D.; Shupegin, M.L.; Bozhko, A.D.

    2009-01-01

    Electrode behavior of nanocomposite films containing titanium- or tungsten-based conducting nanophase embedded in dielectric silicon-carbon matrix, deposited onto glassceramics substrate, is studied by cyclic voltammetry and electrochemical impedance spectroscopy. As the films' resistivity decreases, their electrochemical behavior gradually changes from that of 'poor conductor' to the nearly metal-like behavior. In particular, the differential capacitance increases, the charge transfer in a model redox system [Fe(CN) 6 ] 3-/4- accelerates, which may be explained by the increasing number of metal-containing clusters at the film/electrolyte solution interface

  8. Electrochemical Behavior of La on Liquid Bi electrode in LiCl-KCl molten salt

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Beom Kyu; Han, Hwa Jeong; Park, Byung Gi [Soonchunyang University, Asan (Korea, Republic of)

    2016-05-15

    Pyroprocessing technology aims to achieve a grouped and efficiently separation of all actinide for recycling with a sufficient decontamination of fission products generating the minimum. The main steps of the pyroprocess is electrowinning process, where the remaining elements in a molten salt after electrorifinning process. That process is U, MAs are concurrently recovered at the liquid metal. Recently, a study of the liquid metal and molten salt using an electrochemical is carried out in a variety of fields. However, there is deficient information about the electrode reaction of lanthanide and actinide on the liquid bismuth metal electrodes. In this paper, the electrochemical behavior of La(III), with liquid bismuth was investigated by the electrochemical method. The aim of this study is to investigate the electrochemical behavior of lanthanum or neodymium among lanthanides in molten LiCl-KCl salt at liquid metal bismuth electrode cyclic voltammetry and derive the thermochemical properties. The electrochemical behavior of La was studied in LiCl-KCl-LaCl{sub 3} molten salts using electrochemical techniques Cyclic Voltammetry on liquid Bi electrodes at 773K. During the process of cyclic voltammetry electrolysis, intermetallic compound were observed of La, Lax-Biy, Li-Bi. The diffusion coefficient of La was measured by cyclic voltemmetry and was found to be 8.18x10{sup -5}cm{sup 2}/s.

  9. Electrochemical capacitor behavior of copper sulfide (CuS) nanoplatelets

    Energy Technology Data Exchange (ETDEWEB)

    Justin Raj, C.; Kim, Byung Chul; Cho, Won-Je; Lee, Won-Gil; Seo, Yongseong; Yu, Kook-Hyun, E-mail: yukook@dongguk.edu

    2014-02-15

    Highlights: • The electrochemical supercapacitor electrode was fabricated using CuS nanoplatelets. • CuS electrodes shows better electrochemical properties in aqueous LiClO{sub 4} electrolyte. • The heat treated CuS electrode shows an excellent pseudocapacitance performance than bare CuS electrode. -- Abstract: Copper sulfide (CuS) nanoplatelets have been fabricated by simple low temperature chemical bath deposition technique for electrochemical supercapacitor electrodes. The morphology and structural properties of the electrodes were analyzed using scanning electron microscopy and X-ray diffraction. The effect of heat treatment on electrochemical properties of CuS electrodes were examined by cyclic voltammetry, electrochemical impedance spectroscopy and galvanostatic charge/discharge tests. Results show that bare and heat treated CuS has pseudocapacitive characteristic within the potential range of −0.6 to 0.3 V (vs. Ag/AgCl) in aqueous 1 M LiClO{sub 4} solution. The pseudocapacitance is induced mainly by lithium ions insertion/extraction with the CuS electrodes. The specific capacitance of 72.85 F g{sup −1} was delivered by heat treated CuS film at a scan rate of 5 mV s{sup −1} with an energy and power density of 6.23 W h kg{sup −1} and 1.75 kW kg{sup −1} at 3 Ag{sup −1} constant discharge current which is comparatively higher than that of as deposited CuS electrode.

  10. Electrochemical behavior of quinoxalin-2-one derivatives at mercury electrodes and its analytical use.

    Science.gov (United States)

    Zimpl, Milan; Skopalova, Jana; Jirovsky, David; Bartak, Petr; Navratil, Tomas; Sedonikova, Jana; Kotoucek, Milan

    2012-01-01

    Derivatives of quinoxalin-2-one are interesting compounds with potential pharmacological activity. From this point of view, understanding of their electrochemical behavior is of great importance. In the present paper, a mechanism of electrochemical reduction of quinoxalin-2-one derivatives at mercury dropping electrode was proposed. Pyrazine ring was found to be the main electroactive center undergoing a pH-dependent two-electron reduction process. The molecule protonization of nitrogen in the position 4 precedes the electron acceptance forming a semiquinone radical intermediate which is relatively stable in acidic solutions. Its further reduction is manifested by separated current signal. A positive mesomeric effect of the nonprotonized amino group in the position 7 of the derivative III accelerates the semiquinone reduction yielding a single current wave. The suggested reaction mechanism was verified by means of direct current polarography, differential pulse, cyclic and elimination voltammetry, and coulometry with subsequent GC/MS analysis. The understanding of the mechanism was applied in developing of analytical method for the determination of the studied compounds.

  11. Electrochemical Behavior of Biomedical Titanium Alloys Coated with Diamond Carbon in Hanks' Solution

    Science.gov (United States)

    Gnanavel, S.; Ponnusamy, S.; Mohan, L.; Radhika, R.; Muthamizhchelvan, C.; Ramasubramanian, K.

    2018-03-01

    Biomedical implants in the knee and hip are frequent failures because of corrosion and stress on the joints. To solve this important problem, metal implants can be coated with diamond carbon, and this coating plays a critical role in providing an increased resistance to implants toward corrosion. In this study, we have employed diamond carbon coating over Ti-6Al-4V and Ti-13Nb-13Zr alloys using hot filament chemical vapor deposition method which is well-established coating process that significantly improves the resistance toward corrosion, wears and hardness. The diamond carbon-coated Ti-13Nb-13Zr alloy showed an increased microhardness in the range of 850 HV. Electrochemical impedance spectroscopy and polarization studies in SBF solution (simulated body fluid solution) were carried out to understand the in vitro behavior of uncoated as well as coated titanium alloys. The experimental results showed that the corrosion resistance of Ti-13Nb-13Zr alloy is relatively higher when compared with diamond carbon-coated Ti-6Al-4V alloys due to the presence of β phase in the Ti-13Nb-13Zr alloy. Electrochemical impedance results showed that the diamond carbon-coated alloys behave as an ideal capacitor in the body fluid solution. Moreover, the stability in mechanical properties during the corrosion process was maintained for diamond carbon-coated titanium alloys.

  12. Electrochemical Behavior of Quinoxalin-2-one Derivatives at Mercury Electrodes and Its Analytical Use

    Directory of Open Access Journals (Sweden)

    Milan Zimpl

    2012-01-01

    Full Text Available Derivatives of quinoxalin-2-one are interesting compounds with potential pharmacological activity. From this point of view, understanding of their electrochemical behavior is of great importance. In the present paper, a mechanism of electrochemical reduction of quinoxalin-2-one derivatives at mercury dropping electrode was proposed. Pyrazine ring was found to be the main electroactive center undergoing a pH-dependent two-electron reduction process. The molecule protonization of nitrogen in the position 4 precedes the electron acceptance forming a semiquinone radical intermediate which is relatively stable in acidic solutions. Its further reduction is manifested by separated current signal. A positive mesomeric effect of the nonprotonized amino group in the position 7 of the derivative III accelerates the semiquinone reduction yielding a single current wave. The suggested reaction mechanism was verified by means of direct current polarography, differential pulse, cyclic and elimination voltammetry, and coulometry with subsequent GC/MS analysis. The understanding of the mechanism was applied in developing of analytical method for the determination of the studied compounds.

  13. Electrochemical behavior of molten fluoride-water system

    Energy Technology Data Exchange (ETDEWEB)

    Takenaka, Toshihide; Ito, Yasuhiko; Ishikawa, Takayasu; Oishi, Jun

    1984-11-01

    The cathodic behavior of a molten fluoride-water system was investigated by the potential sweep method. LiF-KF-NaF eutectic melt was used as an electrolyte and HF-H/sub 2/O gas mixture with Ar as a carrier was bubbled into it. Gold wire was used as a working electrode. The peak currents due to the reduction of HF and H/sub 2/O were clearly observed. The relations between peak currents and the square roots of the scanning rates were linear, strongly suggesting that the reduction reactions of the HF and H/sub 2/O dissolved in the melt were diffusion controlled. From the linearity of the relations between peak currents and partial pressures of HF and H/sub 2/O in the low partial pressure region, it was concluded that the concentrations of HF and H/sub 2/O in a fluoride melt are proportional to the partial pressure of each gas. The peak current due to the reduction of OH/sup -/ ion could not be observed, though a clear peak current was observed when OH/sup -/ ion was added to the melt and a cathodic scan was applied immediately. This indicates that OH/sup -/ ion is unstable in a fluoride melt under HF-H/sub 2/O atmosphere.

  14. Electrochemical behavior and voltammetric determination of acetaminophen based on glassy carbon electrodes modified with poly(4-aminobenzoic acid)/electrochemically reduced graphene oxide composite films

    International Nuclear Information System (INIS)

    Zhu, Wencai; Huang, Hui; Gao, Xiaochun; Ma, Houyi

    2014-01-01

    Poly(4-aminobenzoic acid)/electrochemically reduced graphene oxide composite film modified glassy carbon electrodes (4-ABA/ERGO/GCEs) were fabricated by a two-step electrochemical method. The electrochemical behavior of acetaminophen at the modified electrode was investigated by means of cyclic voltammetry. The results indicated that 4-ABA/ERGO composite films possessed excellent electrocatalytic activity towards the oxidation of acetaminophen. The electrochemical reaction of acetaminophen at 4-ABA/ERGO/GCE is proved to be a surface-controlled process involving the same number of protons and electrons. The voltammetric determination of acetaminophen performed with the 4-ABA/ERGO modified electrode presents a good linearity in the range of 0.1–65 μM with a low detection limit of 0.01 μM (S/N = 3). In the case of using the 4-ABA/ERGO/GCE, acetaminophen and dopamine can be simultaneously determined without mutual interference. Furthermore, the 4-ABA/ERGO/GCE has good reproducibility and stability, and can be used to determine acetaminophen in tablets. - Highlights: • The 4-ABA/ERGO/GCE was fabricated by a two-step electrochemical method. • Electrochemical behavior of acetaminophen at the 4-ABA/ERGO/GCE was investigated. • The electrochemical sensor exhibited a low detection limit and good selectivity. • This sensor was applied to the detection of acetaminophen in commercial tablets

  15. Electrochemical behavior and voltammetric determination of acetaminophen based on glassy carbon electrodes modified with poly(4-aminobenzoic acid)/electrochemically reduced graphene oxide composite films

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Wencai [Key Laboratory for Colloid and Interface Chemistry of State Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); School of Chemistry and Chemical Engineering, Qilu Normal University, Jinan 250013 (China); Huang, Hui; Gao, Xiaochun [Key Laboratory for Colloid and Interface Chemistry of State Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Ma, Houyi, E-mail: hyma@sdu.edu.cn [Key Laboratory for Colloid and Interface Chemistry of State Education Ministry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

    2014-12-01

    Poly(4-aminobenzoic acid)/electrochemically reduced graphene oxide composite film modified glassy carbon electrodes (4-ABA/ERGO/GCEs) were fabricated by a two-step electrochemical method. The electrochemical behavior of acetaminophen at the modified electrode was investigated by means of cyclic voltammetry. The results indicated that 4-ABA/ERGO composite films possessed excellent electrocatalytic activity towards the oxidation of acetaminophen. The electrochemical reaction of acetaminophen at 4-ABA/ERGO/GCE is proved to be a surface-controlled process involving the same number of protons and electrons. The voltammetric determination of acetaminophen performed with the 4-ABA/ERGO modified electrode presents a good linearity in the range of 0.1–65 μM with a low detection limit of 0.01 μM (S/N = 3). In the case of using the 4-ABA/ERGO/GCE, acetaminophen and dopamine can be simultaneously determined without mutual interference. Furthermore, the 4-ABA/ERGO/GCE has good reproducibility and stability, and can be used to determine acetaminophen in tablets. - Highlights: • The 4-ABA/ERGO/GCE was fabricated by a two-step electrochemical method. • Electrochemical behavior of acetaminophen at the 4-ABA/ERGO/GCE was investigated. • The electrochemical sensor exhibited a low detection limit and good selectivity. • This sensor was applied to the detection of acetaminophen in commercial tablets.

  16. Corrosion-electrochemical behavior of metals in alkali solutions

    International Nuclear Information System (INIS)

    Levin, V.A.; Levina, E.Eh.

    1995-01-01

    Results of an investigation into corrosion-electrochemical behaviour of 12Kh18N10T, 10Kh17N13M2T, 08Kh21N6M2T and 15Kh25T steels, 06KhN28MDT and KhN78T alloys as well as NP-2 nickel in sodium, potassium and lithium hydroxide solutions at 95-180 deg C temperatures are considered. It is ascertained, that anode polarization curves of all metals irrespective of hydroxide nature, concentration, temperature, presence of chloride and chlorate additions, are of identic character. The movement of anode polarization curves in the direction of lower current of hydroxide type in NaOH-KOH-LiOH series, temperature and solution concentration reduction at other equal terms. 12 refs.; 6 figs

  17. Microstructures and electrochemical behaviors of the friction stir welding dissimilar weld.

    Science.gov (United States)

    Shen, Changbin; Zhang, Jiayan; Ge, Jiping

    2011-06-01

    By using optical microscope, the microstructures of 5083/6082 friction stir welding (FSW) weld and parent materials were analyzed. Meanwhile, at ambient temperature and in 0.2 mol/L NaHS03 and 0.6 mol/L NaCl solutionby gravimetric test, potentiodynamic polarization curve test, electrochemical impedance spectra (EIS) and scanning electron microscope (SEM) observation, the electrochemical behavior of 5083/6082 friction stir welding weld and parent materials were comparatively investigated by gravimetric test, potentiodynamic polarization curve test, electrochemical impedance spectra (EIS) and scanning electron microscope (SEM) observation. The results indicated that at given processing parameters, the anti-corrosion property of the dissimilar weld was superior to those of the 5083 and 6082 parent materials. Copyright © 2011 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

  18. Electrochemical behavior of ionically crosslinked polyampholytic gel electrolytes

    International Nuclear Information System (INIS)

    Chen Wanyu; Tang Haitao; Ou Ziwei; Wang Hong; Yang Yajiang

    2007-01-01

    An ionic complex of anionic and cationic monomers was obtained by protonation of (N,N-diethylamino)ethylmethacrylate (DEA) with acrylic acid (AAc). Free radical copolymerization of the ionic complex and acrylamide (AAm), yielded the ionically crosslinked polyampholytic gel electrolytes [poly(AAc-DEA-AAm), designated as PADA] using two types of organic solvents containing a lithium salt. The PADA gel electrolyte exhibited good thermal stability shown by the DSC thermogram. The impedance analysis at temperatures ranging from -30 to 75 deg. C indicated that the ionic conductivities of the PADA gel electrolytes were rather close to those of liquid electrolytes. The temperature dependence of the ionic conductivities was found to be in accord with the Arrhenius equation. Moreover, the ionic conductivities of PADA gel electrolytes increased with an increase of the molar ratios of cationic/anionic monomers. The ionic conductivities of PADA gels prepared in solvent mixtures of propylene carbonate, ethyl methyl ether and dioxolane (3:1:1, v/v) were higher than those of PADA gels prepared in propylene carbonate only. Significantly, the ionic conductivities of two kinds of PADA gel electrolytes were in the range of 10 -3 and 10 -4 S cm -1 even at -30 deg. C. The electrochemical windows of PADA gel electrolytes measured by cyclic voltammetry were in the range from -1 V to 4.5 V

  19. Study on the Electrochemical Behavior of Iodide at Platinum Electrode in Potassium Chlorate Solution

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Sang Hyuk; Yeon, Jei Won; Song, Kyu Seok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-05-15

    Radioactive iodine-131, is one of the most hazardous fission products which could be released from fuels of nuclear reactors during the severe accident of nuclear power plants. Due to its high radioactivity, high fission yield (2.8%) and hazardous biological effects, the behavior of iodine has been taken interests in many research groups. Iodine is known to be released from the fuels as a cesium iodide form, CsI. And, as nuclear fuels are mostly placed in the water pool, it is easily dissolved in the water after released from the fuels. In water, iodide anion could be oxidized into molecular iodine. As the molecular iodine is a volatile species and the oxidizing rate is affected by many environmental facts such as pH, radiolysis products and temperature, the oxidation reaction of the iodide ion has been considered as an important chemical reaction related to the severe accident of nuclear power plants In present work, the electrochemical behavior of iodide anion was observed by using cyclic voltammetric technique in potassium chlorate solutions. We observed two different oxidation waves in the oxidation potential region. From the comparison with the previous reported results, one is regarded as the oxidation of iodide into molecular iodine. The other is evaluated to be the formation of high-valent iodine-containing compounds

  20. Electrochemical behavior of cysteine at a CuGeO3 nanowires modified glassy carbon electrode

    International Nuclear Information System (INIS)

    Dong Yongping; Pei Lizhai; Chu Xiangfeng; Zhang Wangbing; Zhang Qianfeng

    2010-01-01

    A CuGeO 3 nanowire modified glassy carbon electrode was fabricated and characterized by scanning electron microscopy. The results of electrochemical impedance spectroscopy reveal that electron transfer through nanowire film is facile compared with that of bare glassy carbon electrode. The modified electrode exhibited a novel electrocatalytic behavior to the electrochemical reactions of L-cysteine in neutral solution, which was not reported previously. Two pairs of semi-reversible electrochemical peaks were observed and assigned to the processes of oxidation/reduction and adsorption/desorption of cysteine at the modified electrode, respectively. The electrochemical response of cysteine is poor in alkaline condition and is enhanced greatly in acidic solution, suggesting that hydrogen ions participate in the electrochemical oxidation process of cysteine. The intensities of two anodic peaks varied linearly with the concentration of cysteine in the range of 1 x 10 -6 to 1 x 10 -3 mol L -1 , which make it possible to sensitive detection of cysteine with the CuGeO 3 nanowire modified electrode. Furthermore, the modified electrode exhibited good reproducibility and stability.

  1. Electrochemical corrosion behavior of a Ti-35Nb alloy for medical prostheses

    International Nuclear Information System (INIS)

    Cremasco, Alessandra; Osorio, Wislei R.; Freire, Celia M.A.; Garcia, Amauri; Caram, Rubens

    2008-01-01

    Since the 1980s, the titanium alloys show attractive properties for biomedical applications where the most important factors are, firstly, biocompatibility, corrosion and mechanical resistances, low modulus of elasticity, very good strength to weight ratio, reasonable formability and osseointegration. The aim of this study was to investigate the effects of two different heat treatments; furnace cooling and water quenching, on the general electrochemical corrosion resistance of Ti-35 wt%Nb alloy samples immersed in a 0.9% NaCl (0.15 mol L -1 ) solution at 25 deg. C and neutral pH range. The samples were obtained using a non-consumable tungsten electrode furnace with a water-cooled copper hearth under argon atmosphere. The microstructural pattern was examined by scanning electron microscopy (SEM) and X-ray diffractometry (XRD). In order to evaluate the electrochemical corrosion behavior of such Ti-Nb alloy samples, corrosion tests were performed by using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curves. Analyses of an equivalent circuit have also been used to provide quantitative support for the discussions and understanding of the corrosion behavior. It was found that water quenching provides a microstructural pattern consisting of an alpha-martensite acicular phase which decreases the material electrochemical performance due to the stress-induced martensitic transformation

  2. Electrochemical corrosion behavior of a Ti-35Nb alloy for medical prostheses

    Energy Technology Data Exchange (ETDEWEB)

    Cremasco, Alessandra [Department of Materials Engineering, State University of Campinas, UNICAMP, P.O. Box 6122, 13083-970 Campinas, SP (Brazil); Osorio, Wislei R. [Department of Materials Engineering, State University of Campinas, UNICAMP, P.O. Box 6122, 13083-970 Campinas, SP (Brazil)], E-mail: wislei@fem.unicamp.br; Freire, Celia M.A.; Garcia, Amauri; Caram, Rubens [Department of Materials Engineering, State University of Campinas, UNICAMP, P.O. Box 6122, 13083-970 Campinas, SP (Brazil)

    2008-05-30

    Since the 1980s, the titanium alloys show attractive properties for biomedical applications where the most important factors are, firstly, biocompatibility, corrosion and mechanical resistances, low modulus of elasticity, very good strength to weight ratio, reasonable formability and osseointegration. The aim of this study was to investigate the effects of two different heat treatments; furnace cooling and water quenching, on the general electrochemical corrosion resistance of Ti-35 wt%Nb alloy samples immersed in a 0.9% NaCl (0.15 mol L{sup -1}) solution at 25 deg. C and neutral pH range. The samples were obtained using a non-consumable tungsten electrode furnace with a water-cooled copper hearth under argon atmosphere. The microstructural pattern was examined by scanning electron microscopy (SEM) and X-ray diffractometry (XRD). In order to evaluate the electrochemical corrosion behavior of such Ti-Nb alloy samples, corrosion tests were performed by using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curves. Analyses of an equivalent circuit have also been used to provide quantitative support for the discussions and understanding of the corrosion behavior. It was found that water quenching provides a microstructural pattern consisting of an alpha-martensite acicular phase which decreases the material electrochemical performance due to the stress-induced martensitic transformation.

  3. The Electrochemical Behavior of Dispersions of Spherical Ultramicroelectrodes.

    Science.gov (United States)

    1986-07-30

    means of bipolar electrolyses with dispersions. Polarization equations are predicted for highly simplified models based on the concept of the mixture...three-dimensional electrodes. Bipolar electrolyses on dispersions of spherical particles have been proposed and the behavior of such electrodes in the...photodecomposition of water (e.g. see (32-41)). It should be noted that the size range of the particles which will be most frequently used in dispersion

  4. Electrochemical behavior of tube-fin assembly for an aluminum automotive condenser with improved corrosion resistance

    Science.gov (United States)

    Pech-Canul, M. A.; Guía-Tello, J. C.; Pech-Canul, M. I.; Aguilar, J. C.; Gorocica-Díaz, J. A.; Arana-Guillén, R.; Puch-Bleis, J.

    An aluminum automotive condenser was designed to exhibit high corrosion resistance in the seawater acetic acid test (SWAAT) combining zinc coated microchannel tubes and fins made with AA4343/AA3003(Zn)/AA4343 brazing sheet. Electrochemical measurements in SWAAT solution were carried out under laboratory conditions using tube-fin assembly and individual fin and tube samples withdrawn from the condenser core. The aim was to gain information on the protective role of the zinc sacrificial layer and about changes in corrosion behavior as a function of immersion time. External corrosion of the tube-fin system was simulated by immersion of mini-core samples under open circuit conditions. The corrosion rate increased rapidly during the first 6 h and slowly afterwards. The short time behavior was related to the dissolution of the oxide film and fast dissolution of the outermost part of the zinc diffusion layer. With the aid of cross-sectional depth corrosion potential profiles, it was shown that as the sacrificial layer gets dissolved, the surface concentration of zinc decreases and the potential shifts to less negative values. The results of galvanic coupling of tube and fins in a mini-cell showed that the tube became the anode while the fins exhibited cathodic behavior. An evolution in the galvanic interaction was observed, due to the progressive dissolution of the sacrificial zinc layer. The difference of uncoupled potentials between tube and fins decreased from 71 mV to 32 mV after 84 h of galvanic coupling. At the end of such period there was still a part of the zinc sacrificial layer remaining which would serve for protection of the tube material for even longer periods and there were indications of slight corrosion in the fins.

  5. Electrochemical behavior of tube-fin assembly for an aluminum automotive condenser with improved corrosion resistance

    Directory of Open Access Journals (Sweden)

    M.A. Pech-Canul

    Full Text Available An aluminum automotive condenser was designed to exhibit high corrosion resistance in the seawater acetic acid test (SWAAT combining zinc coated microchannel tubes and fins made with AA4343/AA3003(Zn/AA4343 brazing sheet. Electrochemical measurements in SWAAT solution were carried out under laboratory conditions using tube-fin assembly and individual fin and tube samples withdrawn from the condenser core. The aim was to gain information on the protective role of the zinc sacrificial layer and about changes in corrosion behavior as a function of immersion time. External corrosion of the tube-fin system was simulated by immersion of mini-core samples under open circuit conditions. The corrosion rate increased rapidly during the first 6 h and slowly afterwards. The short time behavior was related to the dissolution of the oxide film and fast dissolution of the outermost part of the zinc diffusion layer. With the aid of cross-sectional depth corrosion potential profiles, it was shown that as the sacrificial layer gets dissolved, the surface concentration of zinc decreases and the potential shifts to less negative values. The results of galvanic coupling of tube and fins in a mini-cell showed that the tube became the anode while the fins exhibited cathodic behavior. An evolution in the galvanic interaction was observed, due to the progressive dissolution of the sacrificial zinc layer. The difference of uncoupled potentials between tube and fins decreased from 71 mV to 32 mV after 84 h of galvanic coupling. At the end of such period there was still a part of the zinc sacrificial layer remaining which would serve for protection of the tube material for even longer periods and there were indications of slight corrosion in the fins. Keywords: Aluminum, Automotive, Corrosion, Galvanic, Zn coating

  6. Investigation of electrochemical synthesis of ferrate, Part I: Electrochemical behavior of iron and its several alloys in concentrated alkaline solutions

    Directory of Open Access Journals (Sweden)

    Čekerevac Milan I.

    2009-01-01

    cyclic voltammetry, galvanostatic and potentiostatic pulse method. Cyclic voltammetry gave useful data on potential regions where ferrate(VI formation is to be expected in the course of transpassive anodic oxidation of iron and some of its alloys, and its stability in the electrolytes of different composition. In addition, step-wise oxidation of iron in anodic oxidation is confirmed. Galvanostatic pulse experiments confirmed the character of successive anodic oxidation of iron, as the three-step process of ferrate(VI formation is clearly observed. In the cathodic pulse complex reduction of ferrate (VI, firstly to Fe(III species and then to mixed Fe(II and Fe(III compounds and finally to elementary iron is confirmed. The significant difference between the mechanisms of anodic oxidation of pure iron and low carbon steel at the one side and electrical ferrous-silicon steel at the other is observed. The influence of material chemical composition on the electrochemical behavior of electrode in course of anodic polarization in strong alkaline solutions is discussed in terms of composition of passivating layer formed on the electrode. On the base of the experimental data, efficient synthesis of ferrate(VI can be expected in the region of anodic potentials between + 0,55 and + 0,75 V against Hg|HgO reference electrode in the same solution, depending on the anode materials composition, in the alkaline electrolytes concentration between 10 and 15 M.

  7. Simulation of electrochemical behavior in Lithium ion battery during discharge process.

    Science.gov (United States)

    Chen, Yong; Huo, Weiwei; Lin, Muyi; Zhao, Li

    2018-01-01

    An electrochemical Lithium ion battery model was built taking into account the electrochemical reactions. The polarization was divided into parts which were related to the solid phase and the electrolyte mass transport of species, and the electrochemical reactions. The influence factors on battery polarization were studied, including the active material particle radius and the electrolyte salt concentration. The results showed that diffusion polarization exist in the positive and negative electrodes, and diffusion polarization increase with the conducting of the discharge process. The physicochemical parameters of the Lithium ion battery had the huge effect on cell voltage via polarization. The simulation data show that the polarization voltage has close relationship with active material particle size, discharging rate and ambient temperature.

  8. Effect of black clay soil moisture on the electrochemical behavior of API X70 pipeline steel

    Science.gov (United States)

    Hendi, R.; Saifi, H.; Belmokre, K.; Ouadah, M.; Smili, B.; Talhi, B.

    2018-03-01

    The effect of moisture content variation (20–100 wt.%) on the electrochemical behavior of API X70 pipeline steel buried in the soil of Skikda (East of Algeria) was studied using electrochemical techniques, scanning electron microscopy (SEM), X ray diffraction analysis (XRD) and weight loss measurement. The electrochemical measurements showed that the corrosion current Icorr is directly proportional to the moisture content up to 50 wt.%, beyond this content, this value becomes almost constant. The result were confirmed by electrochemical impedance spectroscopy; the capacitance of the double layer formed on the surface is the highest at 50 wt.%. A single time constant was detected by plotting the Bode diagrams. The steel surface degradation has been appreciated using the scanning electron microscopy observations. A few pitting corrosion at 20 wt.% moisture, followed by more degradation at 50 wt.% have been revealed. However, when the moisture amount exceeded 50 wt.%, the surface became entirely covered by a corrosion product. XRD analysis revealed the dominance of FeOOH and Fe3O4 phases on steel surface for a moisture content of 50 wt.%.

  9. Electrochemical characterization and redox behavior of Nb-doped SrTiO3

    DEFF Research Database (Denmark)

    Blennow Tullmar, Peter; Kammer Hansen, Kent; Wallenberg, L. Reine

    2009-01-01

    Sr-vacancy compensated Nb-doped SrTiO3 with the nominal composition Sr0.94Ti0.9Nb0.1O3 has been evaluated as a solid oxide fuel cell (SOFC) anode material in terms of redox stability and electrochemical properties. Sr0.94Ti0.9Nb0.1O3 has been synthesized with a recently developed modified glycine......-nitrate process. The phase purity and redox behavior have been analyzed with XRD and TGA. The electrochemical properties of Sr0.94Ti0.9Nb0.1O3 and a composite electrode of Sr0.94Ti0.9Nb0.1O3/YSZ have been investigated by electrochemical impedance spectroscopy (EIS) on cone shaped electrodes and on electrodes...... in a symmetrical cell configuration. The experiments indicated that the Nb-doped SrTiO3 electrodes were redox stable and showed a potential ability to be used as a part of a SOFC anode. The electrochemical activity appeared to be governed by the concentration of defect species (especially Ti3+ and V-0...

  10. Electrochemical behavior of H3PW12O40/ acid-activated bentonite powders

    Directory of Open Access Journals (Sweden)

    Mojović Zorica

    2012-01-01

    Full Text Available Electrochemical behavior of 12-tungstophosphoric acid (HPW/acid-activated bentonite (AAB powders with various loadings of HPW was investigated. The physicochemical properties of the prepared powders were examined by X-ray powder diffraction, nitrogen adsorption-desorption isotherms, atomic force microscopy and cyclic voltammetry measurements. The results indicated that the prepared powders are composed mainly of oriented domains of large rock blocks, probably resulting from a preferable deposition of bentonite particles having a face-to-face interaction. The particles had a mainly disordered mesoporous structure with a pore volume that varied according to the pore size in the range of 2-50 nm. In addition, the particles had crystallite size between 4.9 and 9.0 nm. The electrocatalytic activities of prepared HPW/Aelectrodes were studied in the oxidation of NO2-ions and the results revealed that the electrodes possessed relatively higher nitrite oxidation currents than Aelectrode. The best electroactivity was observed for HPW3/Aelectrode (AAB+20 wt. % HPW and the limit of detection (3σ was determined as 8 μM.

  11. Fabrication and electrochemical behavior of single-walled carbon nanotube/graphite-based electrode

    International Nuclear Information System (INIS)

    Moghaddam, Abdolmajid Bayandori; Ganjali, Mohammad Reza; Dinarvand, Rassoul; Razavi, Taherehsadat; Riahi, Siavash; Rezaei-Zarchi, Saeed; Norouzi, Parviz

    2009-01-01

    An electrochemical method for determining the dihydroxybenzene derivatives on glassy carbon (GC) has been developed. In this method, the performance of a single-walled carbon nanotube (SWCNT)/graphite-based electrode, prepared by mixing SWCNTs and graphite powder, was described. The resulting electrode shows an excellent behavior for redox of 3,4-dihydroxybenzoic acid (DBA). SWCNT/graphite-based electrode presents a significant decrease in the overvoltage for DBA oxidation as well as a dramatic improvement in the reversibility of DBA redox behavior in comparison with graphite-based and glassy carbon (GC) electrodes. In addition, scanning electron microscopy (SEM) and atomic force microscopy (AFM) procedures performed for used SWCNTs

  12. Electrochemical Behavior Assessment of As-Cast Mg-Y-RE-Zr Alloy in Phosphate Buffer Solutions (X Na3PO4 + Y Na2HPO4) Using Electrochemical Impedance Spectroscopy and Mott-Schottky Techniques

    Science.gov (United States)

    Fattah-alhosseini, Arash; Asgari, Hamed

    2018-05-01

    In the present study, electrochemical behavior of as-cast Mg-Y-RE-Zr alloy (RE: rare-earth alloying elements) was investigated using electrochemical tests in phosphate buffer solutions (X Na3PO4 + Y Na2HPO4). X-ray diffraction techniques and Scanning electron microscopy equipped with energy dispersive x-ray spectroscopy were used to investigate the microstructure and phases of the experimental alloy. Different electrochemical tests such as potentiodynamic polarization (PDP), electrochemical impedance spectroscopy (EIS) and Mott-Schottky (M-S) analysis were carried out in order to study the electrochemical behavior of the experimental alloy in phosphate buffer solutions. The PDP curves and EIS measurements indicated that the passive behavior of the as-cast Mg-Y-RE-Zr alloy in phosphate buffer solutions was weakened by an increase in the pH, which is related to formation of an imperfect and less protective passive layer on the alloy surface. The presence of the insoluble zirconium particles along with high number of intermetallic phases of RE elements mainly Mg24Y5 in the magnesium matrix can deteriorate the corrosion performance of the alloy by disrupting the protective passive layer that is formed at pH values over 11. These insoluble zirconium particles embedded in the matrix can detrimentally influence the passivation. The M-S analysis revealed that the formed passive layers on Mg-Y-RE-Zr alloy behaved as an n-type semiconductor. An increase in donor concentration accompanying solutions of higher alkalinity is thought to result in the formation of a less resistive passive layer.

  13. Electrochemical corrosion behaviors of the X90 linepipe steel in NS4 solution

    Directory of Open Access Journals (Sweden)

    Jinheng Luo

    2016-10-01

    Full Text Available Oil and gas line pipes are laid underground and run through different areas in the laying process, so they will be subjected to different degrees of corrosion and even crack, leading to enormous casualties and economic losses. In order to guarantee the safe operation of line pipes, therefore, it is significant to investigate the electrochemical corrosion behaviors of pipe steel in a simulated soil environment. In this paper, the electrochemical corrosion behaviors of the base metals and welding materials of API 5L X90 steel longitudinally submerged arc welding pipes in near-neutral simulated soil solution (NS4 were studied by means of the electrochemical impedance spectroscopy (EIS and the potentiodynamic polarization testing technology. It is shown that the typical characteristic of anodic dissolution is presented but with no passivation phenomenon when X90 linepipe steel is put in NS4 solution. The base material is thermodynamically more stable than the seam weld material. The base material and seam weld samples were polarized under −850 mV polarization potential for different durations. It is demonstrated that with the proceeding of polarization, the polarization resistance and the corrosion resistance increase while the corrosion current density decreases. And the corrosion resistance of base material is better than that of seam weld material.

  14. Effect of aqueous electrolytes on the electrochemical behaviors of supercapacitors based on hierarchically porous carbons

    Science.gov (United States)

    Zhang, Xiaoyan; Wang, Xianyou; Jiang, Lanlan; Wu, Hao; Wu, Chun; Su, Jingcang

    2012-10-01

    Hierarchically porous carbons (HPCs) have been prepared by sol-gel self-assembly technology with nickel oxide and surfactant as the dual template. The porous carbons are further activated by nitric acid. The electrochemical behaviors of supercapacitors using HPCs as electrode material in different aqueous electrolytes, e.g., (NH4)2SO4, Na2SO4, H2SO4 and KOH are studied by cyclic voltametry, galvanostatic charge/discharge, cyclic life, leakage current, self-discharge and electrochemical impedance spectroscopy. The results demonstrate that the supercapacitors in various electrolytes perform definitely capacitive behaviors; especially in 6 M KOH electrolyte the supercapacitor represents the best electrochemical performance, the shortest relaxation time, and nearly ideal polarisability. The energy density of 8.42 Wh kg-1 and power density of 17.22 kW kg-1 are obtained at the operated voltage window of 1.0 V. Especially, the energy density of 11.54 Wh kg-1 and power density of 10.58 kW kg-1 can be achieved when the voltage is up to 1.2 V.

  15. Electrochemical Behavior of Pure Copper in Phosphate Buffer Solutions: A Comparison Between Micro- and Nano-Grained Copper

    Science.gov (United States)

    Imantalab, O.; Fattah-alhosseini, A.; Keshavarz, M. K.; Mazaheri, Y.

    2016-02-01

    In this work, electrochemical behavior of annealed (micro-) and nano-grained pure copper (fabricated by accumulative roll bonding process) in phosphate buffer solutions of various pH values ranging from 10.69 to 12.59 has been studied. Before any electrochemical measurements, evaluation of microstructure was obtained by optical microscope and transmission electron microscopy. To investigate the electrochemical behavior of the samples, the potentiodynamic polarization, Mott-Schottky analysis, and electrochemical impedance spectroscopy (EIS) were carried out. Potentiodynamic polarization plots and EIS measurements revealed that as a result of grain refinement, the passive behavior of the nano-grained sample was improved compared to that of annealed pure copper. Also, Mott-Schottky analysis indicated that the passive films behaved as p-type semiconductors and grain refinement did not change the semiconductor type of passive films.

  16. The electrochemical behavior of some podands at a benzo[c]cinnoline modified glassy carbon electrode

    International Nuclear Information System (INIS)

    Isbir, Aybueke A.; Solak, Ali Osman; Uestuendag, Zafer; Bilge, Selen; Natsagdorj, Amgalan; Kilic, Emine; Kilic, Zeynel

    2005-01-01

    This paper describes the grafting of benzo[c]cinnoline (BCC) molecules on glassy carbon (GC) electrode surface. The attachment of BCC molecules to carbon substrate is induced by the electrochemical reduction of the corresponding diazonium salt. The modification of GC with BCC diazonium salt was done in aprotic solution and proved by blocking of dopamine electron transfer. The presence of BCC at the GC surface was characterized by cyclic voltammetry and X-ray photoelectron spectroscopy (XPS). On modified surface, the electrochemical behavior of two different types of podands and the catalytic effects of the GC-BCC surface were studied. The XPS was used to monitor element characteristics of the adsorbates on the GC surface and confirm the attachment of BCC molecules to the GC surface

  17. The effect of recrystallization on corrosion and electrochemical behavior of 7150 Al alloy

    Energy Technology Data Exchange (ETDEWEB)

    Peng, G.S.; Chen, K.H.; Fang, H.C.; Chen, S.Y.; Chao, H. [State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China)

    2011-01-15

    By weight loss, potentiodynamic polarization, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS) techniques complemented by optical and scanning electron microscopy observations, the effect of recrystallization on the corrosion, and electrochemical behavior of 7150 Al alloy was studied. The results indicated that the high recrystallization fraction 7150-1 was worse than the low recrystallization fraction 7150-2 on corrosion resistance. The analysis of EIS indicated that 7150-1 exhibited obvious pitting corrosion at 5 h immersion time, whereas 7150-2 showed no obvious pitting corrosion even at 33 h. The corrosion route developed along the grain boundary of recrystallization grains, not along the grain boundary of unrecrystallization grains. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  18. Effect of porosity variation on the electrochemical behavior of vertically aligned multi-walled carbon nanotubes.

    Science.gov (United States)

    Raut, Akshay S; Parker, Charles B; Stoner, Brian R; Glass, Jeffrey T

    2012-06-01

    Electrochemical charge storage characteristics of vertically aligned multi-walled carbon nanotubes (MWCNTs) as a function of varying diameter and spacing are reported. It was observed that the specific capacitance of the MWCNTs increased as both diameter and inter-tube spacing decreased. The MWCNT films with 229 nm inter-MWCNT spacing exhibited specific capacitance of 228 F/g versus 70 F/g for 506 nm spacing, when tested in a non-aqueous electrolyte. Further, a trend in specific capacitance versus pore size is proposed. Coupled with previously reported trends observed in the sub-10 nm pore size regime, this is expected to offer better understanding of electrochemical behavior of porous carbon materials over a wide range of pore sizes.

  19. Effect of soil compositions on the electrochemical corrosion behavior of carbon steel in simulated soil solution

    Energy Technology Data Exchange (ETDEWEB)

    Liu, T.M. [College of Materials Science and Engineering, Chongqing University (China); Luo, S.X. [Department of Chemistry, Zunyi Normal College, Zunyi (China); Sun, C. [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang (China); Wu, Y.H.

    2010-04-15

    In this study, effect of cations, Ca{sup 2+}, Mg{sup 2+}, K{sup +}, and anions, SO{sub 4}{sup 2-}, HCO{sub 3}{sup -}, NO{sub 3}{sup -} on electrochemical corrosion behavior of carbon steel in simulated soil solution was investigated through potentiodynamic polarization curves and electrochemical impedance spectroscopy. The results indicate that the Ca{sup 2+}and Mg{sup 2+} can decrease the corrosion current density of carbon steel in simulated soil solution, and K{sup +}, SO{sub 4}{sup 2-}, HCO{sub 3}{sup -}, and NO{sub 3}{sup -} can increase the corrosion density. All the above ions in the simulated soil solution can decrease its resistivity, but they have different effect on the charge transfer resistivity. This finding can be useful in evaluating the corrosivity of certain soil through chemical analysis, and provide data for construction engineers. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  20. Passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solution

    Science.gov (United States)

    Luo, Hong; Su, Huaizhi; Dong, Chaofang; Li, Xiaogang

    2017-04-01

    In this paper, the passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solutions at different pH was evaluated by potentiodynamic measurements, electrochemical impedance spectroscopy. The composition of the passive film and surface morphology were investigated by X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), and scanning electron microscopy, respectively. The results reveal that metastable pitting susceptibility, stable pitting corrosion, and composition of the passive film are influenced by pH value. After long time immersion, a bilayer structure passive film can be formed in this environment. The appearance of molybdates on the outermost surface layer, further enhancing the stability of the passive film. Moreover, the good pitting corrosion resistance of 316L stainless steel in simulated concrete pore solution without carbonated is mainly due to the presence of high Cr/Fe ratio and molybdates ions within the passive film.

  1. Electrochemical behavior of adrenaline at the carbon atom wire modified electrode

    Energy Technology Data Exchange (ETDEWEB)

    Xue Kuanhong [Chemistry Department, Nanjing Normal University, Jiangsu Engineering Research Center for Bio-medical Function Materials, 122 NingHai Road, Nanjing, JiangSu 210097 (China)], E-mail: khxue@njnu.edu.cn; Liu Jiamei [Chemistry Department, Nanjing Normal University, Jiangsu Engineering Research Center for Bio-medical Function Materials, 122 NingHai Road, Nanjing, JiangSu 210097 (China); Wei Ribing [Chemistry Department, Nanjing Normal University, Jiangsu Engineering Research Center for Bio-medical Function Materials, 122 NingHai Road, Nanjing, JiangSu 210097 (China); Chen Shaopeng [Chemistry Department, Nanjing Normal University, Jiangsu Engineering Research Center for Bio-medical Function Materials, 122 NingHai Road, Nanjing, JiangSu 210097 (China)

    2006-09-11

    Electrochemical behavior of adrenaline at an electrode modified by carbon atom wires (CAWs), a new material, was investigated by cyclic voltammetry combined with UV-vis spectrometry, and forced convection method. As to the electrochemical response of redox of adrenaline/adrenalinequinone couple in 0.50 M H{sub 2}SO{sub 4}, at a nitric acid treated CAW modified electrode, the anodic and cathodic peak potentials E {sub pa} and E {sub pc} shifted by 87 mV negatively and 139 mV in the positive direction, respectively, and standard heterogeneous rate constant k {sup 0} increased by 16 times compared to the corresponding bare electrode, indicating the extraordinary activity of CAWs in electrocatalysis for the process.

  2. Electrochemical behavior of adrenaline at the carbon atom wire modified electrode

    Science.gov (United States)

    Xue, Kuan-Hong; Liu, Jia-Mei; Wei, Ri-Bing; Chen, Shao-Peng

    2006-09-01

    Electrochemical behavior of adrenaline at an electrode modified by carbon atom wires (CAWs), a new material, was investigated by cyclic voltammetry combined with UV-vis spectrometry, and forced convection method. As to the electrochemical response of redox of adrenaline/adrenalinequinone couple in 0.50 M H 2SO 4, at a nitric acid treated CAW modified electrode, the anodic and cathodic peak potentials Epa and Epc shifted by 87 mV negatively and 139 mV in the positive direction, respectively, and standard heterogeneous rate constant k0 increased by 16 times compared to the corresponding bare electrode, indicating the extraordinary activity of CAWs in electrocatalysis for the process.

  3. Electrochemical behavior of adrenaline at the carbon atom wire modified electrode

    International Nuclear Information System (INIS)

    Xue Kuanhong; Liu Jiamei; Wei Ribing; Chen Shaopeng

    2006-01-01

    Electrochemical behavior of adrenaline at an electrode modified by carbon atom wires (CAWs), a new material, was investigated by cyclic voltammetry combined with UV-vis spectrometry, and forced convection method. As to the electrochemical response of redox of adrenaline/adrenalinequinone couple in 0.50 M H 2 SO 4 , at a nitric acid treated CAW modified electrode, the anodic and cathodic peak potentials E pa and E pc shifted by 87 mV negatively and 139 mV in the positive direction, respectively, and standard heterogeneous rate constant k 0 increased by 16 times compared to the corresponding bare electrode, indicating the extraordinary activity of CAWs in electrocatalysis for the process

  4. Electrochemical behavior of thin anodic oxide films on Zircaloy-4: Role of the mobile defects

    International Nuclear Information System (INIS)

    Salot, R.; Lefebvre-Joud, F.; Baroux, B.

    1996-01-01

    The first stages of the electrochemical oxidation of Zircaloy-4 are investigated using simple electrochemical tests and modeling the passive film modifications occurring as a result of contact with the electrolyte. Variations in electrode potential (open-circuit conditions) or current density (potentiodynamic scans) can be simply explained by a high field (F ∼ 10 6 V/cm) assisted passive film growth. Under open-circuit conditions, this field does not vary with exposure time (in the 2 h to 48 h range). The minimum electric field for the onset of high-field behavior is also evaluated and found smaller than the theoretical value which can be explained by a variation in the concentration of mobile defects throughout the film. Measurements of the electrode potential decay after a potentiodynamic scan confirm this model, allowing interpretation of the film modification as a combination of two separate phenomena: film growth under a high electric field and point defect annihilation

  5. Behavioral Indicators and Behaviors Related to Sexting among Undergraduate Students

    Science.gov (United States)

    Hudson, Heather K.; Fetro, Joyce V.; Ogletree, Roberta

    2014-01-01

    Background: Empirical studies on sexting are limited, and many sexting studies only assessed sexting behaviors. Few studies have assessed attitudes, subjective norms, or behavioral intentions related to sexting. Purpose: The purpose of this study was to assess attitudes, subjective norms, behavioral intentions, and behaviors related to sexting…

  6. Enrofloxacin behavior in presence of soil extracted organic matter: An electrochemical approach

    International Nuclear Information System (INIS)

    Antilén, Monica; Valencia, Camila; Peralta, Emilia; Canales, Camila; Espinosa-Bustos, Christian; Escudey, Mauricio

    2017-01-01

    In this work, a novel and simple method aimed at determining and quantifying Enrofloxacin in presence of Natural Organic Matter (NOM) is proposed. The method was based on the electrochemical oxidation of Enrofloxacin by using cyclic voltammetry as technique. It was found that this analyte presents a good electroactivity, in absence and in presence of NOM. However, this electrochemical behavior is highly pH-dependent, since the reaction is more favorable when less acid the media is. At this point, different pH values were studied in order to corroborate this phenomenon. Additionally, kinetic studies were done to determine the control of the reaction, the number of transferred electrons in the entire process and the rate determining step of the reaction by analyzing the Tafel slope. With these antecedents, a mechanism was proposed and the final product of the reaction was corroborated by using LC-MS. Finally, analytical parameters were studied with the aim of proposing this new method as an electrochemical sensor of Enrofloxacin. It was found that the method is highly linear, precise and accurate. Moreover, this method is not only sensitive but also selective to Enrofloxacin in presence of NOM, in comparison to spectrophotometric methods previously reported.

  7. Electrochemical corrosion behavior of Ni-containing hypoeutectic Al-Si alloy

    Directory of Open Access Journals (Sweden)

    Abul Hossain

    2015-12-01

    Full Text Available Electrochemical corrosion characteristics of the thermally treated 2 wt % Ni-containing Al-6Si-0.5Mg alloy were studied in NaCl solutions. The corrosion behavior of thermally treated (T6 Al-6Si-0.5Mg (-2Ni alloys in 0.1 M NaCl solution was investigated by electrochemical potentiodynamic polarization technique consisting of linear polarization method using the fit of Tafel plot and electrochemical impedance spectroscopy (EIS techniques. Generally, linear polarization experiments revealed a decrease of the corrosion rate at thermal treated Al-6Si-0.5Mg-2Ni alloy. The EIS test results showed that there is no significant change in charge transfer resistance (Rct after addition of Ni to Al-6Si-0.5Mg alloy. The magnitude of the positive shift in the open circuit potential (OCP, corrosion potential (Ecorr and pitting corrosion potential (Epit increased with the addition of Ni to Al-6Si-0.5Mg alloy. The forms of corrosion in the studied Al-6Si-0.5Mg alloy (except Al-6Si-0.5Mg-2Ni alloy are pitting corrosion as obtained from the scanning electron microscopy (SEM study.

  8. Electrochemical performances and capacity fading behaviors of activated carbon/hard carbon lithium ion capacitor

    International Nuclear Information System (INIS)

    Sun, Xianzhong; Zhang, Xiong; Liu, Wenjie; Wang, Kai; Li, Chen; Li, Zhao; Ma, Yanwei

    2017-01-01

    Highlights: • Three-electrode pouch cell is used to investigate the capacity fading of AC/HC LIC. • the electrode potential swing is critical for the cycleability of a LIC cell. • Different capacity fading behaviors are discussed. • A large-capacity LIC pouch cell has been assembled with a specific energy of 18.1 Wh kg −1 based on the total weight. - Abstract: Lithium ion capacitor (LIC) is one of the most promising electrochemical energy storage devices, which offers rapid charging-discharging capability and long cycle life. We have fabricated LIC pouch cells using an electrochemically-driven lithium pre-doping method through a three-electrode pouch cell structure. The active materials of cathode and anode of LIC cell are activated carbon and pre-lithiated hard carbon, respectively. The electrochemical performances and the capacity fading behaviors of LICs in the voltage range of 2.0 − 4.0 V have been studied. The specific energy and specific power reach 73.6 Wh kg −1 and 11.9 kW kg −1 based on the weight of the active materials in both cathode and anode, respectively. Since the cycling performance is actually determined by hard carbon anode, the anode potential swings are emphasized. The capacity fading of LIC upon cycling is proposed to be caused by the increases of internal resistance and the consumption of lithium stored in anode. Finally, a large-capacity LIC pouch cell has been assembled with a maximum specific energy of 18.1 Wh kg −1 and a maximum specific power of 3.7 kW kg −1 based on the weight of the whole cell.

  9. Effects of water plasma immersion ion implantation on surface electrochemical behavior of NiTi shape memory alloys in simulated body fluids

    International Nuclear Information System (INIS)

    Liu, X.M.; Wu, S.L.; Chu, Paul K.; Chung, C.Y.; Chu, C.L.; Yeung, K.W.K.; Lu, W.W.; Cheung, K.M.C.; Luk, K.D.K.

    2007-01-01

    Water plasma immersion ion implantation (PIII) was conducted on orthopedic NiTi shape memory alloy to enhance the surface electrochemical characteristics. The surface composition of the NiTi alloy before and after H 2 O-PIII was determined by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) was utilized to determine the roughness and morphology of the NiTi samples. Potentiodynamic polarization tests and electrochemical impedance spectroscopy (EIS) were carried out to investigate the surface electrochemical behavior of the control and H 2 O-PIII NiTi samples in simulated body fluids (SBF) at 37 deg. C as well as the mechanism. The H 2 O-PIII NiTi sample showed a higher breakdown potential (E b ) than the control sample. Based on the AFM results, two different physical models with related equivalent electrical circuits were obtained to fit the EIS data and explain the surface electrochemical behavior of NiTi in SBF. The simulation results demonstrate that the higher resistance of the oxide layer produced by H 2 O-PIII is primarily responsible for the improvement in the surface corrosion resistance

  10. Electrochemical corrosion behavior of AZ91D alloy in ethylene glycol

    International Nuclear Information System (INIS)

    Fekry, A.M.; Fatayerji, M.Z.

    2009-01-01

    The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride 0.05 M for fluoride containing ethylene glycol solution, some inhibition effect has been observed. The corrosion of AZ91D alloy in the blank can be effectively inhibited by addition of 0.05 mM paracetamol that reacts with AZ91D alloy and forms a protective film on the surface at this concentration as confirmed by surface examination.

  11. Microstructural characterization and electrochemical corrosion behavior of Incoloy 800 in sulphate and chloride solutions

    International Nuclear Information System (INIS)

    Mansur, Fabio Abud; Schvartzman, Monica Maria de Abreu Mendonca; Campos, Wagner Reis da Costa; Aguiar, Antonio Eugenio de; Chaim, Marcos Souza

    2011-01-01

    Corrosion has been the major cause of tube failures in steam generators (SG) tubes in nuclear power plants. Problems have resulted from impurities in the secondary water systems which are originated from leaks of cooling water. It is important to understand the compatibility of steam generator tube materials with the environment. This study presents the microstructural characterization and electrochemical behavior of the Incoloy 800 in sodium chloride and sodium sulphate aqueous solutions at 80 degree C. Potentiodynamic anodic polarization, cyclic polarization and open circuit potential (OCP) measurements were the electrochemical techniques applied in this work. The pitting resistance of Incoloy 800 in chloride plus sulphate mixtures were also examined. Experiments performed in solutions with different concentrations of Cl- and SO 4 2- ions in solution (200 ppb, 500 ppb, 1ppm, 5 ppm, 50 ppm and 100 ppm) showed that this concentrations range had no substantial effect on the anodic behavior of the alloy. After polarization no localized corrosion was found on the samples. (author)

  12. Electrochemical behavior of single-walled carbon nanotube supercapacitors under compressive stress.

    Science.gov (United States)

    Li, Xin; Rong, Jiepeng; Wei, Bingqing

    2010-10-26

    The effect of compressive stress on the electrochemical behavior of flexible supercapacitors assembled with single-walled carbon nanotube (SWNT) film electrodes and 1 M aqueous electrolytes with different anions and cations were thoroughly investigated. The under-pressed capacitive and resistive features of the supercapacitors were studied by means of cyclic voltammetry measurements and electrochemical impedance analysis. The results demonstrated that the specific capacitance increased first and saturated in corresponding decreases of the series resistance, the charge-transfer resistance, and the Warburg diffusion resistance under an increased pressure from 0 to 1723.96 kPa. Wettability as well as ion-size effect of different aqueous electrolytes played important roles to determine the pressure dependence behavior of the suerpcapacitors under an applied pressure. An improved high-frequency capacitive response with 1172 Hz knee frequency, which is significantly higher compared to reported values, was observed under the compressive pressure of 1723.96 kPa, indicating an improving and excellent high-power capability of the supercapacitors under the pressure. The experimental results and the thorough analysis described in this work not only provide fundamental insight of pressure effects on supercapacitors but also give an important guideline for future design of next generation flexible/stretchable supercapacitors for industrial and consumer applications.

  13. Electrochemical corrosion behavior of AZ91D alloy in ethylene glycol

    Energy Technology Data Exchange (ETDEWEB)

    Fekry, A.M. [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)], E-mail: hham4@hotmail.com; Fatayerji, M.Z. [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)

    2009-11-01

    The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride <0.05 M containing 30% ethylene glycol solution, they are more corrosive than the blank (30% ethylene glycol-70% water). However, at concentrations <0.05 for chloride or >0.05 M for fluoride containing ethylene glycol solution, some inhibition effect has been observed. The corrosion of AZ91D alloy in the blank can be effectively inhibited by addition of 0.05 mM paracetamol that reacts with AZ91D alloy and forms a protective film on the surface at this concentration as confirmed by surface examination.

  14. Electrochemical behavior and voltammetric determination of acetaminophen based on glassy carbon electrodes modified with poly(4-aminobenzoic acid)/electrochemically reduced graphene oxide composite films.

    Science.gov (United States)

    Zhu, Wencai; Huang, Hui; Gao, Xiaochun; Ma, Houyi

    2014-12-01

    Poly(4-aminobenzoic acid)/electrochemically reduced graphene oxide composite film modified glassy carbon electrodes (4-ABA/ERGO/GCEs) were fabricated by a two-step electrochemical method. The electrochemical behavior of acetaminophen at the modified electrode was investigated by means of cyclic voltammetry. The results indicated that 4-ABA/ERGO composite films possessed excellent electrocatalytic activity towards the oxidation of acetaminophen. The electrochemical reaction of acetaminophen at 4-ABA/ERGO/GCE is proved to be a surface-controlled process involving the same number of protons and electrons. The voltammetric determination of acetaminophen performed with the 4-ABA/ERGO modified electrode presents a good linearity in the range of 0.1-65 μM with a low detection limit of 0.01 μM (S/N=3). In the case of using the 4-ABA/ERGO/GCE, acetaminophen and dopamine can be simultaneously determined without mutual interference. Furthermore, the 4-ABA/ERGO/GCE has good reproducibility and stability, and can be used to determine acetaminophen in tablets. Copyright © 2014 Elsevier B.V. All rights reserved.

  15. Electrochemical behavior of nanostructured MnO2/C (Vulcan® composite in aqueous electrolyte LiNO3

    Directory of Open Access Journals (Sweden)

    Vujković Milica

    2011-01-01

    Full Text Available The electrolytic solutions of contemporary Li-ion batteries are made exclusively with the organic solvents since anodic materials of these batteries have potentials with greater negativity than the potential of the water reduction, thus the organic electrolytes can withstand the voltages of 3-5 V that are characteristic for these batteries. Ever since it was discovered that some materials can electrochemically intercalate and deintercalate Li+ ions in aqueous solutions, numerous studies have been conducted with the aim of extending operational time of the aqueous Li-ion batteries. Manganese oxide has been studied as the electrode material in rechargeable lithium-ion batteries with organic electrolytes. In this paper its electrochemical behavior as an anode material in aqueous electrolyte solutions was examined. MnO2 as a component of nanodispersed MnO2/C (Vulcan® composite was successfully synthesized hydrothermally. Electrochemical properties of this material were investigated in aqueous saturated LiNO3 solution by both cyclic voltammetry and galvanostatic charging/discharging (LiMn2O4 as cathode material techniques. The obtained composite shows a relatively good initial discharge capacity of 96.5 mAh/g which, after 50th charging/discharging cycles, drops to the value of 57mAh/g. MnO2/C (Vulcan® composite, in combination with LiMn2O4 as a cathode material, shows better discharge capacity compared to other anodic materials used in aqueous Li-ion batteries according to certain studies that have been conducted. Its good reversibility and cyclability, and the fact that hydrothermal method is simple and effective, makes MnO2/C(Vulcan® composite a promising anodic material for aqueous Li-ion batteries.

  16. Microscopic Insights into the Electrochemical Behavior of Non-aqueous Electrolytes in Supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Deen [ORNL; Wu, Jianzhong [ORNL

    2013-01-01

    Electric double-layer capacitors (EDLC) are electrical devices that store energy by adsorption of ionic species at the inner surface of porous electrodes. Compared with aqueous electrolytes, ionic liquid and organic electrolytes have the advantage of larger potential windows, making them attractive for the next generation of EDLC with superior energy and power densities. The performance of both ionic liquid and organic electrolyte EDLC hinges on the judicious selection of the electrode pore size and the electrolyte composition that requires a comprehension of the charging behavior from a microscopic view. In this perspective, we discuss predictions from the classical density functional theory (CDFT) on the dependence of the capacitance on the pore size for ionic-liquid and organic-electrolyte EDLC. CDFT is applicable to electrodes with the pore size ranging from that below the ionic dimensionality to mesoscopic scales, thus unique for investigating the electrochemical behavior of the confined electrolytes for EDLC applications.

  17. Heterogeneous structure and its effect on properties and electrochemical behavior of ion-exchange membrane

    Science.gov (United States)

    Ariono, D.; Khoiruddin; Subagjo; Wenten, I. G.

    2017-02-01

    Generally, commercially available ion-exchange membrane (IEM) can be classified into homogeneous and heterogeneous membranes. The classification is based on degree of heterogeneity in membrane structure. It is well known that the heterogeneity greatly affects the properties of IEM, such as conductivity, permselectivity, chemical and mechanical stability. The heterogeneity also influences ionic and electrical current transfer behavior of IEM-based processes during their operation. Therefore, understanding the role of heterogeneity in IEM properties is important to provide preliminary information on their operability and applicability. In this paper, the heterogeneity and its effect on IEM properties are reviewed. Some models for describing the heterogeneity of IEM and methods for characterizing the degree of heterogeneity are discussed. In addition, the influence of heterogeneity on the performance of IEM-based processes and their electrochemical behavior are described.

  18. An electrochemical study of the corrosion behavior of primer coated 2219-T87 aluminum

    Science.gov (United States)

    Danford, M. D.; Higgins, R. H.

    1985-01-01

    The corrosion behavior for 2219-T87 aluminum coated with various primers, including those used for the external tank and solid rocket boosters of the Space Shuttle Transportation System, were investigated using electrochemical techniques. Corrosion potential time, polarization resistance time, electrical resistance time, and corrosion rate time measurements were all investigated. It was found that electrical resistance time and corrosion rate time measurement were most useful for studying the corrosion behavior of painted aluminum. Electrical resistance time determination give useful information concerning the porosity of paint films, while corrosion rate time curves give important information concerning overall corrosion rates and corrosion mechanisms. In general, the corrosion rate time curves all exhibited at least one peak during the 30 day test period, which was attributed, according to the proposed mechanisms, to the onset of the hydrogen evolution reaction and the beginning of destruction of the protective properties of the paint film.

  19. Electrochemical behavior of high performance on-chip porous carbon films for micro-supercapacitors applications in organic electrolytes

    Science.gov (United States)

    Brousse, K.; Huang, P.; Pinaud, S.; Respaud, M.; Daffos, B.; Chaudret, B.; Lethien, C.; Taberna, P. L.; Simon, P.

    2016-10-01

    Carbide derived carbons (CDCs) are promising materials for preparing integrated micro-supercapacitors, as on-chip CDC films are prepared via a process fully compatible with current silicon-based device technology. These films show good adherence on the substrate and high capacitance thanks to their unique nanoporous structure which can be fine-tuned by adjusting the synthesis parameters during chlorination of the metallic carbide precursor. The carbon porosity is mostly related to the synthesis temperature whereas the thickness of the films depends on the chlorination duration. Increasing the pore size allows the adsorption of large solvated ions from organic electrolytes and leads to higher energy densities. Here, we investigated the electrochemical behavior and performance of on-chip TiC-CDC in ionic liquid solvent mixtures of 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIBF4) diluted in either acetonitrile or propylene carbonate via cyclic voltammetry and electrochemical impedance spectroscopy. Thin CDC films exhibited typical capacitive signature and achieved 169 F cm-3 in both electrolytes; 65% of the capacitance was still delivered at 1 V s-1. While increasing the thickness of the films, EMI+ transport limitation was observed in more viscous PC-based electrolyte. Nevertheless, the energy density reached 90 μW h cm-2 in 2M EMIBF4/ACN, confirming the interest of these CDC films for micro-supercapacitors applications.

  20. The Electrochemical Behavior of SnSb as an Anode for Li-ion Batteries Studied by Electrochemical Impedance Spectroscopy and Electron Microscopy

    International Nuclear Information System (INIS)

    Tesfaye, Alexander T.; Yücel, Yasemin D.; Barr, Maïssa K.S.; Santinacci, Lionel; Vacandio, Florence; Dumur, Frédéric; Maria, Sébastien; Monconduit, Laure; Djenizian, Thierry

    2017-01-01

    Highlights: •Electrochemical behavior of SnSb is investigated by EIS, SEM and TEM. •Formation of SEI and cracks occurs during cycling experiments. •The capacity fading as a result of the electrode modifications is discussed. -- Abstract: Evolution of the electrical and morphological properties of micron-sized SnSb has been investigated to understand the electrochemical behavior observed during cycling experiments. Electron microscopy techniques (scanning electron microscopy and transmission electron microscopy) and electrochemical impedance spectroscopy have been combined to evidence the electrode modifications and particularly the formation of a solid electrolyte interphase (SEI) layer. Evolution of the SEI resistance and the charge transfer resistance with the cell voltage can be explained by the electrolyte degradation and expansion/contraction of the electrode. Furthermore, we show that the SEI formation is not limited at the first discharge/charge of the battery. The continuous growth of the SEI layer up to 50 cycles associated to the electrode pulverization caused by the large volume variations are responsible for the capacity fading.

  1. Studies of the corrosion and cracking behavior of steels in high temperature water by electrochemical techniques

    International Nuclear Information System (INIS)

    Cheng, Y.F.; Bullerwell, J.; Steward, F.R.

    2003-01-01

    Electrochemical methods were used to study the corrosion and cracking behavior of five Fe-Cr alloy steels and 304L stainless steel in high temperature water. A layer of magnetite film forms on the metal surface, which decreases the corrosion rate in high temperature water. Passivity can be achieved on A-106 B carbon steel with a small content of chromium, which cannot be passivated at room temperature. The formation rate and the stability of the passive film (magnetite film) increased with increasing Cr-content in the steels. A mechanistic model was developed to simulate the corrosion and cracking processes of steels in high temperature water. The crack growth rate on steels was calculated from the maximum current of the repassivation current curves according to the slip-oxidation model. The highest crack growth rate was found for 304L stainless steel in high temperature water. Of the four Fe-Cr alloys, the crack growth rate was lower on 0.236% Cr- and 0.33% Cr-steels than on 0.406% Cr-steel and 2.5% Cr-1% Mo steel. The crack growth rate on 0.33% Cr-steel was the smallest over the tested potential range. A higher temperature of the electrolyte led to a higher rate of electrochemical dissolution of steel and a higher susceptibility of steel to cracking, as shown by the positive increase of the electrochemical potential. An increase in Cr-content in the steel is predicted to reduce the corrosion rate of steel at high temperatures. However, this increase in Cr-content is predicted not to reduce the susceptibility of steel to cracking at high temperatures. (author)

  2. On the Electrochemical Behavior of PVD Ti-Coated AISI 304 Stainless Steel in Borate Buffer Solution

    Science.gov (United States)

    Fattah-alhosseini, Arash; Elmkhah, Hassan; Attarzadeh, Farid Reza

    2017-04-01

    This work aims at studying the electrochemical behavior of annealed pure titanium (Ti) and nano-structured (NS) Ti coating in borate buffer solutions. Cathodic arc evaporation was successfully applied to deposit NS Ti coating. Samples were characterized by means of scanning electron microscope and x-ray diffraction. Potentiodynamic polarization tests, electrochemical impedance spectroscopy, and Mott-Schottky analysis were employed to discuss the electrochemical behavior of samples thoroughly. Electrochemical measurements showed that the deposited NS Ti coating offers a superior passivity in borate buffer solutions of pH 9.0 and 9.5. Mott-Schottky analysis revealed that all passive films are of n-type semiconducting nature in these alkaline solutions and the deposition process did not alter the semiconducting type of passive films formed on samples. Additionally, this analysis showed that the NS Ti coating possessed lower levels of donor densities. Finally, all electrochemical tests showed that passive behavior of the NS Ti samples was superior, mainly due to the formation of thicker and less defective passive films.

  3. Electrochemical Corrosion Behavior of Oxidation Layer on Fe30Mn5Al Alloy

    Directory of Open Access Journals (Sweden)

    ZHU Xue-mei

    2017-08-01

    Full Text Available The Fe30Mn5Al alloy was oxidized at 800℃ in air for 160h, the oxidation-induced layer about 15μm thick near the scale-metal interface was induced to transform to ferrite and become enriched in Fe and depletion in Mn. The effect of the oxidation-induced Mn depletion layer on the electrochemical corrosion behavior of Fe30Mn5Al alloy was evaluated. The results show that in 1mol·L-1 Na2SO4 solution, the anodic polarization curve of the Mn depletion layer exhibits self-passivation, compared with Fe30Mn5Al austenitic alloy, and the corrosion potential Evs SCE is increased to -130mV from -750mV and the passive current density ip is decreased to 29μA/cm2 from 310μA/cm2. The electrochemical impedance spectroscopy(EIS of the Mn depletion layer has the larger diameter of capacitive arc, the higher impedance modulus|Z|, and the wider phase degree range, and the fitted polarization resistant Rt is increased to 9.9kΩ·cm2 from 2.7kΩ·cm2 by using an equivalent electric circuit of Rs-(Rt//CPE. The high insulation of the Mn depletion layer leads to an improved corrosion resistance of Fe30Mn5Al austenitic alloy.

  4. Microstructure and electrochemical behavior of cerium conversion coating modified with silane agent on magnesium substrates

    Science.gov (United States)

    Lei, Li; Shi, Jing; Wang, Xin; Liu, Dan; Xu, Haigang

    2016-07-01

    The cerium conversion coating with and without different concentrations of silane agent bis-(γ-triethoxysilylpropyl)-tetrasulfide (BTESPT) modification is obtained on magnesium alloys. Detailed properties of the coatings and the role of BTESPT as an additive are studied and followed with careful discussion. The coating morphology, wettability, chemical composition and corrosion resistance are characterized by scanning electronic microscope (SEM), water contact-angle, X-ray photoelectron spectroscopy (XPS), potentiodynamic measurements and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of the coatings is investigated using EIS. The results indicate that the coating morphology and composition can be controlled by changing silane concentration. The combination of cerium ions and silane molecules could promote the formation of more homogenous and higher hydrophobic coating. The coating turns to be more compact and the adhesive strength between the coating and the magnesium substrate are strongly improved with the formation of Sisbnd Osbnd Si and Sisbnd Osbnd M chemical bonds. The optimum corrosion resistance of the coating in the corrosive media is obtained by 25 ml L-1 BTESPT modification. This whole study implies that the cerium conversion coating modified with certain silane agent deserves cautiousness before its application for corrosion resistance.

  5. In-vitro bioactivity and electrochemical behavior of polyaniline encapsulated titania nanotube arrays for biomedical applications

    Science.gov (United States)

    Agilan, P.; Rajendran, N.

    2018-05-01

    Titania nanotube arrays (TNTA) have attracted increasing attention due to their outstanding properties and potential applications in biomedical field. Fabrication of titania nanotubes on titanium surface enhances the biocompatibility. Polyaniline (PANI) is one of the best conducting polymers with remarkable corrosion resistance and reasonable biocompatibility. In this work, the corrosion resistance and biocompatibility of polyaniline encapsulated TiO2 nanotubes for orthopaedic applications were investigated. The vertically oriented, highly ordered TiO2 nanotubes were fabricated on titanium by electrochemical anodization process using fluoride containing electrolytes. The anodization parameters viz., voltage, pH, time and electrolyte concentration were optimized to get orderly arranged TNTA. Further, the conducting polymer PANI was encapsulated on TNTA by electropolymerization process to enhance the corrosion resistance. The nanostructure of the fabricated TNTA and polyaniline encapsulated titania nanotube arrays (PANI-TNTA) were investigated by HR SEM analysis. The formed phases and functional groups were find using XRD, ATR-FTIR. The hydrophilic surface of TNTA and PANI-TNTA was identified by water contact angle studies. The corrosion behavior of specimens was evaluated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization studies. In-vitro immersion studies were carried out in simulated body fluid solution (Hanks' solution) to evaluate the bioactivity of the TNTA and PANI-TNTA. The surface morphological studies revealed the formation of PANI on the TNTA surface. Formation of hydroxyapatite (HAp) on the surfaces of TNTA and PANI-TNTA enhanced the bioactivity and corrosion resistance.

  6. Electrochemical behavior of rhodium(III) in 1-butyl-3-methylimidazolium chloride ionic liquid

    Energy Technology Data Exchange (ETDEWEB)

    Jayakumar, M.; Venkatesan, K.A. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Srinivasan, T.G. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)], E-mail: tgs@igcar.gov.in

    2008-02-15

    Electrochemical behavior of rhodium(III) chloride in 1-butyl-3-methylimidazolium chloride was investigated by various electrochemical transient techniques at glassy carbon working electrode at different temperatures (343-373 K). Cyclic voltammogram of rhodium(III) in bmimCl consisted of a surge in reduction current occurring at a potential of -0.48 V (vs. Pd) is due to the reduction of Rh(III) to metallic rhodium and a very small oxidation wave occurring at -0.1 V. Increase of scan rate increases the peak current and remarkably shifts the cathodic peak potential (E{sub p}{sup c1}) in negative direction indicating the irreversibility of electroreduction of rhodium(III). The diffusion coefficient of rhodium(III) in bmimCl ({approx}10{sup -9} cm{sup 2}/s) was determined and the energy of activation ({approx}25 kJ/mol) was deduced from cyclic voltammograms at various temperatures. The cathodic ({tau}{sub r}) and anodic ({tau}{sub o}) transition times were measured from chronopotential transients and the ratio {tau}{sub o}/{tau}{sub r} was found to be 1:7. Electrowinning of rhodium from bmimCl medium results in a deposition of metallic rhodium with lower (20-25%) Faradaic efficiency. A separation factor of rhodium from co-existing noble metal fission product palladium in bmimCl was determined during electrodeposition.

  7. Electrochemical behavior of fission palladium in 1-butyl-3-methylimidazolium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Jayakumar, M.; Venkatesan, K.A.; Srinivasan, T.G. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)

    2007-08-01

    Electrochemical behavior of palladium (II) chloride in 1-butyl-3-methylimidazolium chloride has been investigated by various electrochemical transient techniques using glassy carbon working electrode at different temperatures (343-373 K). Cyclic voltammogram consisted of a prominent reduction wave at -0.61 V (vs. Pd) due to the reduction of Pd(II) to Pd, and two oxidation waves at -0.26 and 0.31 V. A nucleation loop is observed at -0.53 V. The diffusion coefficient of palladium (II) in bmimCl ({proportional_to}10{sup -7} cm{sup 2}/s) was determined and the energy of activation (63 kJ/mol) was deduced from the cyclic voltammograms at various temperatures. Nucleation and growth of palladium on glassy carbon working electrode has been investigated by chronoamperometry and chronopotentiometry. The growth and decay of chronocurrents measured for palladium deposition has been found to follow the instantaneous nucleation model with three-dimensional growth of nuclei. The surface morphology of the deposit obtained at various applied potentials revealed the formation of dendrites immediately after nucleation and spread in all the directions with time. (author)

  8. Experimental characterization of electrochemically polymerized polycarbazole film and study of its behavior with different metals contacts

    Science.gov (United States)

    Srivastava, Aditi; Chakrabarti, P.

    2017-12-01

    In this paper, we present the method of fabrication, experimental characterization, and comparison of electrical parameters of semiconducting polycarbazole film with different rectifying metals contacts. Electrochemical polymerization and deposition of organic semiconductor, i.e., polycarbazole on ITO-coated glass substrate, were performed using an electrochemical workstation. Experimental characterization of the prepared polymer film was done in respect of morphology, absorption, bandgap, and thickness. The stability and electro-activity of polycarbazole film were verified by the cyclic voltammetric method. Study of the behavior of prepared polycarbazole film with the different metals contacts such as Aluminum, Copper, Tungsten, and Tin has been done using semiconductor device analyzer. Various electrical parameters such as barrier height, ideality factor, and reverse saturation current have been extracted with different metal contacts, and the values were compared and contrasted. The nature of I- V characteristic of polycarbazole film in non-contact mode has also been analyzed using scanning tunneling microscope. The rectifying I- V characteristics obtained with different metals contacts have also been validated by the simulation on Deckbuild platform of the of ATLAS® software tool from Silvaco Inc.

  9. Influence of cold work on electrochemical behavior of 316L ASS in PEMFC environment

    Science.gov (United States)

    Tandon, Vipin; Patil, Awanikumar P.; Rathod, Ramesh C.; Shukla, Sourabh

    2018-02-01

    The influence of cold work (CW) on electrochemical behavior of 316L ASS in PEMFC (0.5M H2SO4 + 2 ppm HF at 70 °C) environment was investigated by microstructural observations, x-ray diffraction (XRD), polarization, electrochemical impedance spectroscopy (EIS) and Mott-Schottky (M-S) techniques. The XRD is used to analyze the increase in dislocation density and formation of α‧-martensite with increasing CW degree. The EIS is used to find out the effect of substrate dislocation density on the film resistance. The EIS result show that with increasing CW, the diameter of depressed semi-circular arc and consequently film resistance decreased. This indicates the formation of highly disordered and porous film on CW. From PDP results, it is found that icrit, ip and icorr increased on increasing CW degree. Moreover, the direct relationship was drawn from the dislocation density of the substrate to the defect density of the passive film from M-S technique.

  10. Passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solution

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Hong, E-mail: luohong@hhu.edu.cn [College of Mechanics and Materials, Hohai University, Nanjing 210098 (China); Su, Huaizhi [State Key Laboratory of Hydrology-Water Resources and Hydraulic Engineering, Hohai University, Nanjing 210098,China (China); Dong, Chaofang; Li, Xiaogang [Institute of Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083,China (China)

    2017-04-01

    Highlights: • The pH value play an important role on passive mechanism of stainless steel. • The relationship between Cr/Fe ratio within the passive film and pH is non-linear. • Better corrosion resistance due to high Cr/Fe ratio and molybdates ions. - Abstract: In this paper, the passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solutions at different pH was evaluated by potentiodynamic measurements, electrochemical impedance spectroscopy. The composition of the passive film and surface morphology were investigated by X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), and scanning electron microscopy, respectively. The results reveal that metastable pitting susceptibility, stable pitting corrosion, and composition of the passive film are influenced by pH value. After long time immersion, a bilayer structure passive film can be formed in this environment. The appearance of molybdates on the outermost surface layer, further enhancing the stability of the passive film. Moreover, the good pitting corrosion resistance of 316L stainless steel in simulated concrete pore solution without carbonated is mainly due to the presence of high Cr/Fe ratio and molybdates ions within the passive film.

  11. Electrochemical behavior of low phosphorus electroless Ni-P-Si3N4 composite coatings

    International Nuclear Information System (INIS)

    Balaraju, J.N.; Ezhil Selvi, V.; Rajam, K.S.

    2010-01-01

    In the present investigation the electroless Ni-P-Si 3 N 4 composite coatings were prepared by using a low phosphorus bath containing submicron size silicon nitride particles. Plain Ni-P deposits were also prepared for comparison. The phosphorus contents present in electroless plain Ni-P and Ni-P-Si 3 N 4 coatings are 3.7 and 3.4 wt.%, respectively. Scanning electron microscope (SEM) images obtained for composite coatings (cross-sections) showed that the second phase particles are uniformly distributed throughout the thickness of the deposits. It was found that nodularity increased with particle codeposition in Ni-P matrix. To find out the electrochemical behavior of plain Ni-P and composite coatings, potentiodynamic polarization and electrochemical impedance (EIS) studies were carried out in 3.5 wt.% sodium chloride solution in non-deaerated condition. Second phase particle incorporation in Ni-P matrix indicated a marginal decrease in corrosion current density compared to the plain Ni-P deposits. This was further confirmed by EIS studies and SEM analysis of the corroded samples.

  12. Passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solution

    International Nuclear Information System (INIS)

    Luo, Hong; Su, Huaizhi; Dong, Chaofang; Li, Xiaogang

    2017-01-01

    Highlights: • The pH value play an important role on passive mechanism of stainless steel. • The relationship between Cr/Fe ratio within the passive film and pH is non-linear. • Better corrosion resistance due to high Cr/Fe ratio and molybdates ions. - Abstract: In this paper, the passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solutions at different pH was evaluated by potentiodynamic measurements, electrochemical impedance spectroscopy. The composition of the passive film and surface morphology were investigated by X-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS), and scanning electron microscopy, respectively. The results reveal that metastable pitting susceptibility, stable pitting corrosion, and composition of the passive film are influenced by pH value. After long time immersion, a bilayer structure passive film can be formed in this environment. The appearance of molybdates on the outermost surface layer, further enhancing the stability of the passive film. Moreover, the good pitting corrosion resistance of 316L stainless steel in simulated concrete pore solution without carbonated is mainly due to the presence of high Cr/Fe ratio and molybdates ions within the passive film.

  13. The electrochemical behavior and surface structure of titanium electrodes modified by ion beams

    International Nuclear Information System (INIS)

    Huang, G.F.; Xie, Z.; Huang, W.Q.; Yang, S.B.; Zhao, L.H.

    2004-01-01

    Industrial grade titanium modified by ion implantation and sputtering was used as electrodes. The effect of ion beam modification on the electrochemical behavior and surface structure of electrodes was investigated. Also discussed is the hydrogen evolution process of the electrode in acidic solution. Several ions such as Fe + , C + , W + , Ni + and others, were implanted into the electrode. The electrochemical tests were carried out in 1N H 2 SO 4 solution at 30±1 deg. C. The electrode potential was measured versus a saturate calomel electrode as a function of immersion time. The cathodic polarization curves were measured by the stable potential static method. The surface layer composition and the chemical state of the electrodes were also investigated by Auger electron spectrometer (AES) and X-ray photoelectron spectroscopy (XPS) technique. The results show that: (1) the stability of modified electrodes depends on the active elements introduced by ion implantation and sputtering deposition. (2) The hydrogen evolution activity of industrial grade titanium may be improved greatly by ion beam modification. (3) Ion beam modification changed the composition and the surface state of electrodes over a certain depth range and forms an activity layer having catalytic hydrogen evolution, which inhibited the absorption of hydrogen and formation of titanium hydride. Thus promoted hydrogen evolution and improved the hydrogen evolution catalytic activity in industrial grade titanium

  14. Effects of Ce, La and Ba addition on the electrochemical behavior of super duplex stainless steels

    International Nuclear Information System (INIS)

    Yoo, Yun-Ha; Choi, Yoon-Seok; Kim, Jung-Gu; Park, Yong-Soo

    2010-01-01

    The effects of rare earth metal (REM: Ce, La) and Ba addition on aqueous corrosion properties of super duplex stainless steels (SDSS) were investigated by electrochemical tests and surface analyses. The results of potentiodynamic test indicated that the passive range increased by the addition of Ce, La, and Ba, indicating increased relative resistance to localized corrosion. The EIS measurements showed that the Ce-La-Ba-bearing alloys exhibited higher R ct and R p values than the Ce-La-Ba-free alloy at the passive and breakdown states. Furthermore, the additions of REMs and Ba together promoted the formation of dense chromium-enriched passive film.

  15. Photo-electrochemical Investigation of Radiation-Enhanced Galvanic Coupling and Hydrogen Permeation in TPBAR-related Materials

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-10-02

    Research conducted in FY17 used photo-electrochemical methods to investigate the potential for radiationenhanced galvanic coupling in tritium-producing burnable absorber rod (TPBAR) materials. Specifically, a laboratory electrochemical cell was coupled with UV light in order to perform electrochemical opencircuit voltage and galvanic current measurements, techniques that have been used successfully in previous studies to replicate galvanic processes in reactor settings. UV irradiation can mimic reactor-like behavior because, similar to both directly and indirectly ionizing radiation, UV photons with energy greater than the band gap of the material will generate free charge carriers (electrons and holes) and can substantially alter the passivating effect of metal oxides.

  16. Photo-electrochemical Investigation of Radiation-Enhanced Galvanic Coupling and Hydrogen Permeation in TPBAR-related Materials

    International Nuclear Information System (INIS)

    Larsen, G.

    2017-01-01

    Research conducted in FY17 used photo-electrochemical methods to investigate the potential for radiationenhanced galvanic coupling in tritium-producing burnable absorber rod (TPBAR) materials. Specifically, a laboratory electrochemical cell was coupled with UV light in order to perform electrochemical opencircuit voltage and galvanic current measurements, techniques that have been used successfully in previous studies to replicate galvanic processes in reactor settings. UV irradiation can mimic reactor-like behavior because, similar to both directly and indirectly ionizing radiation, UV photons with energy greater than the band gap of the material will generate free charge carriers (electrons and holes) and can substantially alter the passivating effect of metal oxides.

  17. An extensive study of electrochemical behavior of brimonidine and its determination at glassy carbon electrode

    International Nuclear Information System (INIS)

    Aleksić, Mara M.; Radulović, Valentina; Agbaba, Danica; Kapetanović, Vera

    2013-01-01

    Highlights: • The electrochemical behavior of BRIM was investigated by CV, DPV and SWV at GCE. • The effects of pH, scan rate and BRIM concentriation was studied. • The nature of the electrode process, and the mechanism scheme was proposed. • DPV method was developed for the estimation of BRIM in the Alphagan eye drops. -- Abstract: The electrochemical behavior of brimonidine (BRIM), an antiglaucoma agent applied in therapy for lowering high intraocular pressure, was investigated by cyclic voltammetry, differential pulse voltammetry and square wave voltammetry using a glassy carbon electrode (GCE). The reduction of BRIM occurs as one-step quasi-reversible reaction in acid and neutral medium, reaching the full reversibility in alkaline solutions. Reduction process involves the transfer of two electrons and two protons at the pyrazine ring of quinoxaline moiety, forming a dihydro-derivative. In acid and neutral solutions, brimonidine reduction product is partly oxidized to its hydroxy-derivative. BRIM is also oxidized irreversibly with the transfer of one electron and one proton at secondary amine moiety. The effects of pH of the electrolyte solution, scan rate and BRIM concentration were monitored. The nature of the electrode process was found to be controlled by the adsorption at pH > 6 and the total surface concentration of brimonidine adsorbed onto the GCE surface at pH 7, Γ BRIM = 1.35 × 10 −10 mol cm −2 was obtained. Based on this study, differential pulse voltammetric method was developed, validated and suggested for rapid electroanalytical determination of the low concentration of brimonidine. The linearity was achieved within the concentration range from 5 × 10 −7 to 5 × 10 −6 M with LOD = 1.6 × 10 −7 M and LOQ = 5.3 × 10 −7 M. The method was applied for brimonidine determination in pharmaceutical dosage form, eye drops

  18. Electrochemical behavior of Q235 steel in saltwater saturated with carbon dioxide based on new imidazoline derivative inhibitor

    International Nuclear Information System (INIS)

    Liu, F.G.; Du, M.; Zhang, J.; Qiu, M.

    2009-01-01

    The electrochemical behavior of carbon steel in saltwater saturated with CO 2 with/without an new synthesized imidazoline inhibitor was studied using polarization and electrochemical impedance spectrum (EIS), and the inhibitive ability of the inhibitor was evaluated by weight-loss method in 298-328 K temperature range. Results showed that the inhibition efficiency is up to above 80%, and imidazoline is a kind of mixed-type inhibitor. It was seen that the adsorption of imidazoline on Q235 steel can be fitted to Frumkin isotherm equation. Quantum chemistry calculation results show that the imidazoline ring and heteroatoms are the active sites of the inhibitors

  19. Electrochemical migration, whisker formation, and corrosion behavior of printed circuit board under wet H2S environment

    International Nuclear Information System (INIS)

    Zou, Shiwen; Li, Xiaogang; Dong, Chaofang; Ding, Kangkang; Xiao, Kui

    2013-01-01

    Highlights: •The electrochemical migration, whisker formation, and corrosion behavior of PCB under wet H 2 S environment were observed and studied systematically. •The process of electrochemical migration of solder joints is explained. •The corrosion mechanism of PCB interconnectors induced by micro pores under wet H 2 S environment is discussed, and the corrosion reaction model is proposed. -- Abstract: Electrochemical migration, whisker formation, and corrosion behavior of printed circuit board (PCB) under wet H 2 S environment were analyzed by environment scanning electron microscope (ESEM), Energy dispersive X-ray spectroscopy (EDS) with mapping and element phase cluster (EPC) techniques, Raman Spectrum analysis and electrochemical impedance spectroscopy (EIS) technology. The results showed that nonuniform corrosion behavior occurred on PCB surfaces under 1 ppm wet H 2 S at 40 °C; whiskers formed on the inner sidewall of via-holes with a growth rate of 1.2 Å/s; numerous corrosion products migrated through the pore of plated gold layer, which broke off the protective layer. The corrosion rate was accelerated according to the big-cathode-small-anode model

  20. Electrochemical approach to corrosion behavior of ferritic steels in Flibe melt

    International Nuclear Information System (INIS)

    Nishimura, H.; Suzuki, A.; Terai, T.; Kondo, M.; Sagara, A.; Noda, N.

    2007-01-01

    Full text of publication follows: A mixture of LiF-BeF 2 , Flibe, is considered as a candidate material for tritium breeding in a fusion liquid blanket. Flibe has favorable characteristics such as high chemical stability and low electric conductivity. However, it produces TF with neutron irradiation, which is corrosive to structural materials. Therefore, the compatibility of structural materials with Flibe is a critical issue. Up to the present, the compatibility of some materials with Flibe was examined by carrying out simple immersion tests under limited conditions. By visual observations and analyses such as XRD on the surfaces after washing out Flibe from specimens, it was found that ferritic steels seemed to have good compatibility. However, strictly speaking, surface condition of the specimens should not be same as that during immersion in melt because these specimens were subjected to heat treatments and washing processes in order to remove solidified Flibe. Therefore, we planed electrochemical experiment to observe corrosion behavior during immersion. In this study, by carrying out cyclic voltammetry on specimens to observe alteration of surface condition of specimen in Flibe melt from moment to moment, the compatibility of ferritic steel with Flibe melt was discussed on. JLF-1 JOYO-II heat ferritic steel (Fe-9.000r-1.98W-0.09C-0.49Mn-0.20V-0.083Ta) which is a candidate low activation ferritic steel as a structural material of fusion reactor was chosen as a test specimen. Fe-9Cr and Fe-2W alloys were also chosen for comparison. The size of all specimens was 20 x 10 x 1 mm. A electrochemical cell was assembled using these specimens as working electrodes. Pt was chosen as a material for quasi-reference electrode. A Ni crucible which was the container of electrolyte, Flibe, was used as a counter electrode. 600 grams of Flibe was prepared and purified by HF/H 2 bubbling before being filled in the Ni crucible. Each specimen was dunked into Flibe at 773, 823 and

  1. Electrochemical behavior of anodized AA6063-T6 alloys affected by matrix structures

    International Nuclear Information System (INIS)

    Huang, Yung-Sen; Shih, Teng-Shih; Wu, Chen-En

    2013-01-01

    Highlights: ► Deformation after solution treatment introduced Al matrix to have deformation bands and few Si particles. ► Dislocations remained in the matrix lift up field potential and produce AlOOH oxide in the AAO film. ► The silicon-containing particles were found to trap in the AAO film. ► The silicon particles and the Al(OOH) oxide is significantly to influence the electrochemical behavior of AAO films. - Abstract: AA 6063 alloys were cold-rolled (CR) either before or after solution treatment (S) and then different samples were artificially aged (T6) to obtain different samples (CRST6 and SCRT6). The highest dislocation density was observed in the SCRT6 sample which also showed the lowest particle count among the three samples; ST6, CRST6 and SCRT6. Subsequently, all samples were anodized in a 15 wt% sulfuric acid solution for different time spans to obtain anodic aluminum oxide (AAO) films. The anodized samples were further analyzed with X-ray Photoelectron Spectroscopy (XPS) analysis. We determined that the constituent phases in the AAO film were composed of hydrated amorphous alumina, hydrated oxide (Al(OH) 3 ) and oxyhydroxide (AlOOH) phases together with some silicon-containing particles trapped in the films on all samples. In the electrochemical test, the silicon-containing particles and hydrated Al(OH) 3 oxide that existed at the electrolyte/film (e/f) interface were found to inversely influence the corrosion resistance of the anodized samples.

  2. Relational models for knowledge sharing behavior

    NARCIS (Netherlands)

    Boer, N.I.; Berends, J.J.; Baalen, P.

    2011-01-01

    In this paper we explore the relational dimension of knowledge sharing behavior by proposing a comprehensive theoretical framework for studying knowledge sharing in organizations. This theoretical framework originates from (Fiske, 1991) and (Fiske, 1992) Relational Models Theory (RMT). The RMT

  3. Electrochemical behaviors of wax-coated Li powder/Li 4Ti 5O 12 cells

    Science.gov (United States)

    Park, Han Eol; Seong, Il Won; Yoon, Woo Young

    The wax-coated Li powder specimen was effectively synthesized using the drop emulsion technique (DET). The wax layer on the powder was verified by SEM, Focused Ion Beam (FIB), EDX and XPS. The porosity of a sintered wax-coated Li electrode was measured by linear sweep voltammetry (LSV) and compared with that of a bare, i.e., un-coated Li electrode. The electrochemical behavior of the wax-coated Li powder anode cell was examined by the impedance analysis and cyclic testing methods. The cyclic behavior of the wax-coated Li powder anode with the Li 4Ti 5O 12 (LTO) cathode cell was examined at a constant current density of 0.35 mA cm -2 with the cut-off voltages of 1.2-2.0 V at 25 °C. Over 90% of the initial capacity of the cell remained even after the 300th cycle. The wax-coated Li powder was confirmed to be a stable anode material.

  4. An electrochemical investigation of the corrosion behavior of aluminum alloys in chloride containing solutions

    International Nuclear Information System (INIS)

    Campos Filho, Jorge Eustaquio de

    2005-01-01

    Aluminum alloys have been used as cladding materials for nuclear fuel in research reactors due to its corrosion resistance. Aluminum owes its good corrosion resistance to a protective barrier oxide film formed and strongly bonded to its surface. In pool type TRIGA IPR-R1 reactor, located at Centro de Desenvolvimento da Tecnologia Nuclear in Belo Horizonte, previous immersion coupon tests revealed that aluminum alloys suffer from pitting corrosion, in spite of high quality of water control. Corrosion attack is initiated by breaking the protective oxide film on aluminum alloy surface. Chloride ions can break this oxide film and stimulate metal dissolution. In this study the aluminum alloys 1050, 5052 and 6061 were used to evaluate their corrosion behavior in chloride containing solutions. The electrochemical techniques used were potentiodynamic anodic polarization and cyclic polarization. Results showed that aluminum alloys 5052 and 6061 present similar corrosion resistance in low chloride solutions (0,1 ppm NaCl) and in reactor water but both alloys are less resistant in high chloride solution (1 ppm NaCl). Aluminum alloy 1050 presented similar behavior in the three electrolytes used, regarding to pitting corrosion, indicating that the concentration of the chloride ions was not the only variable to influence its corrosion susceptibility. (author)

  5. Electrodeposition and Capacitive Behavior of Films for Electrodes of Electrochemical Supercapacitors

    Directory of Open Access Journals (Sweden)

    Shi C

    2010-01-01

    Full Text Available Abstract Polypyrrole films were deposited by anodic electropolymerization on stainless steel substrates from aqueous pyrrole solutions containing sodium salicylate and tiron additives. The deposition yield was studied under galvanostatic conditions. The amount of the deposited material was varied by the variation of deposition time at a constant current density. SEM studies showed the formation of porous films with thicknesses in the range of 0–3 μm. Cyclic voltammetry data for the films tested in 0.5 M Na2SO4 solutions showed capacitive behavior and high specific capacitance (SC in a voltage window of 0.9 V. The films prepared from pyrrole solutions containing tiron showed better capacitive behavior compared to the films prepared from the solutions containing sodium salicylate. A highest SC of 254 F g−1 was observed for the sample with a specific mass of 89 μg cm−2 at a scan rate of 2 mV s−1. The SC decreased with an increasing film thickness and scan rate. The results indicated that the polypyrrole films deposited on the stainless steel substrates by anodic electropolymerization can be used as electrodes for electrochemical supercapacitors (ES.

  6. Electrodeposition and Capacitive Behavior of Films for Electrodes of Electrochemical Supercapacitors

    Science.gov (United States)

    Shi, C.; Zhitomirsky, I.

    2010-03-01

    Polypyrrole films were deposited by anodic electropolymerization on stainless steel substrates from aqueous pyrrole solutions containing sodium salicylate and tiron additives. The deposition yield was studied under galvanostatic conditions. The amount of the deposited material was varied by the variation of deposition time at a constant current density. SEM studies showed the formation of porous films with thicknesses in the range of 0-3 μm. Cyclic voltammetry data for the films tested in 0.5 M Na2SO4 solutions showed capacitive behavior and high specific capacitance (SC) in a voltage window of 0.9 V. The films prepared from pyrrole solutions containing tiron showed better capacitive behavior compared to the films prepared from the solutions containing sodium salicylate. A highest SC of 254 F g-1 was observed for the sample with a specific mass of 89 μg cm-2 at a scan rate of 2 mV s-1. The SC decreased with an increasing film thickness and scan rate. The results indicated that the polypyrrole films deposited on the stainless steel substrates by anodic electropolymerization can be used as electrodes for electrochemical supercapacitors (ES).

  7. Electrochemical Corrosion Behavior of Low Carbon I-Beam Steels In Simulated Yucca Mountain Repository Environment

    Energy Technology Data Exchange (ETDEWEB)

    Arjunan, Venugopal; Lamb, Joshua; Chandra, Dhanesh; Daemen, Jack; Jones, Denny A.; Engelhard, Mark H.; Lea, Alan S.

    2005-04-01

    The electrochemical corrosion behavior of low carbon steel was examined in a simulated Yucca Mountain (YM) ground water by varying the electrolyte concentration and temperature under aerated and deaerated conditions. The results show that in deaerated conditions, the corrosion rate is low in the order of 0.6 to 4.5mpy, between 25 to 85 C, respectively. However, in aerated conditions the measured rates were expectedly very high, in the order of 3-55mpy in the above mentioned temperature levels. The rates initially increased up to 45 C, and a decreasing trend was observed with further increase in temperature from 65 to 85 C. The maximum corrosion rate was occurred at 45 C (54.5mpy). The low corrosion rates observed in all deaerated conditions, and in aerated solutions at higher temperatures were due to the preferential adsorption of Mg-species on the steel surface, as identified by XPS analyses. The results also indicate possible localized corrosion behavior of carbon steel in aerated conditions up to 45 C.

  8. Electrochemical Corrosion Behavior of Low Carbon I-Beam Steels In Simulated Yucca Mountain Repository Environment

    International Nuclear Information System (INIS)

    Arjunan, Venugopal; Lamb, Joshua; Chandra, Dhanesh; Daemen, Jack; Jones, Denny A.; Engelhard, Mark H.; Lea, Alan S.

    2005-01-01

    The electrochemical corrosion behavior of low carbon steel was examined in a simulated Yucca Mountain (YM) ground water by varying the electrolyte concentration and temperature under aerated and deaerated conditions. The results show that in deaerated conditions, the corrosion rate is low in the order of 0.6 to 4.5mpy, between 25 to 85 C, respectively. However, in aerated conditions the measured rates were expectedly very high, in the order of 3-55mpy in the above mentioned temperature levels. The rates initially increased up to 45 C, and a decreasing trend was observed with further increase in temperature from 65 to 85 C. The maximum corrosion rate was occurred at 45 C (54.5mpy). The low corrosion rates observed in all deaerated conditions, and in aerated solutions at higher temperatures were due to the preferential adsorption of Mg-species on the steel surface, as identified by XPS analyses. The results also indicate possible localized corrosion behavior of carbon steel in aerated conditions up to 45 C

  9. Changing Food Related Behavior Through Design

    DEFF Research Database (Denmark)

    Hermanssdottir, Sunna; Fisker, Anna Marie; Poulsen, Søren Bolvig

    The aim of the workshop is to explore how designers can work actively and deliberately with changing food related behavior through socially responsible design. There will be focus on the holistic aspect of behavioral food design with active involving of the users experience. The workshop is based...

  10. Trust mediates conservation-related behaviors

    Science.gov (United States)

    Patricia L. Winter; George Cvetkovich

    2010-01-01

    In this article we explore the influence that a perceived connection between a natural resource management agency and individual citizens has upon conservation-related behaviors on public lands, offering an extension of psychology’s examination of environmental behaviors. Our emphasis is upon perceived value similarity and resulting trust between citizens and the USDA...

  11. Effect of niobium element on the electrochemical corrosion behavior of depleted uranium

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Yanping, E-mail: wuyanping-2@126.com; Wu, Quanwen; Zhu, Shengfa, E-mail: zhushf-306@163.com; Pu, Zhen; Zhang, Yanzhi; Wang, Qinguo; Lang, Dingmu; Zhang, Yuping

    2016-09-15

    Depleted uranium (DU) has many military and civilian uses. However, its high chemical reactivity limits its application. The effect of Nb content on corrosion behavior of DU is evaluated by scanning Kelvin probe and electrochemical corrosion measurements. The Volta potential value of DU and U-2.5 wt% Nb is about the same level, the Volta potential value of U-5.7 wt% Nb has a rise of 370mV{sub SHE} in comparison with DU. The polarization current of U-5.7 wt% Nb alloy is about an order of magnitude of that of DU. The Nb{sub 2}O{sub 5} is the protective layer for the U-Nb alloys. The negative potential of Nb-depleted α phase is the main reason of the poor corrosion resistance of DU and U-2.5 wt% Nb alloy. - Highlights: • New method (scanning Kelvin probe) was used to study the corrosion property. • Three types of corrosion morphologies were found after potentiodynamic polarization. • The effect of impurity elements on corrosion property was mentioned. • The corrosion mechanism of DU and U-Nb alloys was discussed.

  12. Effect of composition on the electrochemical behavior of austenitic stainless steel in Ringer's solution

    International Nuclear Information System (INIS)

    Bandy, R.; Cahoon, J.R.

    1977-01-01

    Potentiodynamic cyclic polarization tests on Type 316L stainless steel, a common orthopedic implant alloy, in Ringer's solution show considerable hysteresis and a protection potential more active than the open circuit corrosion potential. This implies that chances of repassivation of actively growing pits in this alloy are limited. Tests in Ringer's solution containing hydrochloric acid show that the open circuit potential of Type 316L steel in this solution may exceed in the noble direction the critical pitting potential in the same solution. This signifies that spontaneous breakdown of passivity may occur in a bulk environment which grossly simulates the electrochemical environment within a crevice. Alloying elements such as Mo, Ni, Cr, all improve the corrosion resistance of Type 316L stainless steel in that the critical pitting potential shifts in the noble direction in the alloys having any of the three alloying elements in a higher proportion than in Type 316L steel. Polarization tests in Ringer's solution on a 20% Cr, 25% Ni, 4.5% Mo, 1.5% Cu austenitic stainless steel, having Mo, Cr, and Ni--all in higher proportions than in Type 316L steel, does not show any critical pitting potential or hysteresis at potentials below that for dissociation of water. However, test in 4% NaCl solution at 60 C, a more aggressive chloride environment than Ringer'ssolution, reveals considerable hysteresis and a very active protection potential, indicating that this behavior is a common feature of austenitic stainless steel in sufficiently aggressive, chloride media

  13. Electro-Chemical Behavior of Low Carbon Steel Under H2S Influence

    Science.gov (United States)

    Zaharia, M. G.; Stanciu, S.; Cimpoesu, R.; Nejneru, C.; Savin, C.; Manole, V.; Cimpoeșu, N.

    2017-06-01

    Abstract A commercial low carbon steel material (P265GH) with application at industrial scale for natural gas delivery and transportation systems was analyzed in H2S atmosphere. The article proposed a new experimental cell in order to establish the behavior of the material in sulfur contaminated environment. In most of the industrial processes for gas purification the corrosion rate is speed up by the presence of S (sulfur) especially as ions or species like H2S. The H2S (hydrogen sulfide) is, beside a very toxic compound, a very active element in the acceleration of metallic materials deterioration especially in complex solicitations like pressure and temperature in the same time. For experiments we used a three electrodes cell with Na2SO4 + Na2S solution at pH 3 at room temperature (∼ 25 °C) to realize EIS (electrochemical impedance spectroscopy) and potentio-dynamic polarization experiments. Scanning electron microscopy and X-ray dispersive energy spectroscopy were used to characterize the metallic material surface exposed to experimental environment.

  14. Effects of chitosan inhibitor on the electrochemical corrosion behavior of 2205 duplex stainless steel

    Science.gov (United States)

    Yang, Se-fei; Wen, Ying; Yi, Pan; Xiao, Kui; Dong, Chao-fang

    2017-11-01

    The effects of chitosan inhibitor on the corrosion behavior of 2205 duplex stainless steel were studied by electrochemical measurements, immersion tests, and stereology microscopy. The influences of immersion time, temperature, and chitosan concentration on the corrosion inhibition performance of chitosan were investigated. The optimum parameters of water-soluble chitosan on the corrosion inhibition performance of 2205 duplex stainless steel were also determined. The water-soluble chitosan showed excellent corrosion inhibition performance on the 2205 duplex stainless steel. Polarization curves demonstrated that chitosan acted as a mixed-type inhibitor. When the stainless steel specimen was immersed in the 0.2 g/L chitosan solution for 4 h, a dense and uniform adsorption film covered the sample surface and the inhibition efficiency (IE) reached its maximum value. Moreover, temperature was found to strongly influence the corrosion inhibition of chitosan; the inhibition efficiency gradually decreased with increasing temperature. The 2205 duplex stainless steel specimen immersed in 0.4 g/L water-soluble chitosan at 30°C displayed the best corrosion inhibition among the investigated specimens. Moreover, chitosan decreased the corrosion rate of the 2205 duplex stainless steel in an FeCl3 solution.

  15. Electrochemical behavior and microstructural characterization of 1026 Ni-B coated steel

    International Nuclear Information System (INIS)

    Contreras, A.; Leon, C.; Jimenez, O.; Sosa, E.; Perez, R.

    2006-01-01

    Ni-B coatings have been deposited on the surfaces of commercial steels (SAE-1026). The depositions were carried out using the electroless plating technique employing a nickel chloride solution with borane-dimethylamine as the reducing agent. These specimens were subsequently heat treated at different temperatures (300-500 deg. C) and different periods of time. The obtained coating thickness was in the order of approximately 1.5 μm. X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques were used to characterize the structure and superficial morphology of the coatings. Phases like Ni, Ni 3 B and Ni 4 B 3 were observed through X-ray diffraction and confirmed by differential scanning calorimeter (DSC) studies. Some of the precipitated phases have been structurally characterized. The corrosion behavior of the coated surfaces was carried out by electrochemical impedance spectroscopy (EIS) using electrolytic sodium chlorine solutions with pH 2 and 7. The EIS results showed an active corrosion mechanism in acid solution while diffusion-reaction phenomena are predominant in neutral solution

  16. Electrochemical reduction behavior of simplified simulants of vitrified radioactive waste in molten CaCl2

    Science.gov (United States)

    Katasho, Yumi; Yasuda, Kouji; Nohira, Toshiyuki

    2018-05-01

    The electrochemical reduction of two types of simplified simulants of vitrified radioactive waste, simulant 1 (glass component only: SiO2, B2O3, Na2O, Al2O3, CaO, Li2O, and ZnO) and simulant 2 (also containing long-lived fission product oxides, ZrO2, Cs2O, PdO, and SeO2), was investigated in molten CaCl2 at 1103 K. The behavior of each element was predicted from the potential-pO2- diagram constructed from thermodynamic data. After the immersion of simulant 1 into molten CaCl2 without electrolysis, the dissolution of Na, Li, and Cs was confirmed by inductively coupled plasma atomic emission spectrometry and mass spectrometry analysis of the samples. The scanning electron microscopy/energy dispersive X-ray and X-ray diffraction analyses of simulants 1 and 2 electrolyzed at 0.9 V vs. Ca2+/Ca confirmed that most of SiO2 had been reduced to Si. After the electrolysis of simulants 1 and 2, Al, Zr, and Pd remained in the solid phase. In addition, SeO2 was found to remain partially in the solid phase and partially evaporate, although a small quantity dissolved into the molten salt.

  17. Electrochemical behavior of rhodium acetamidate immobilized on a carbon paste electrode: a hydrazine sensor

    Directory of Open Access Journals (Sweden)

    Gil Eric de S.

    2000-01-01

    Full Text Available The electrochemical behavior of rhodium acetamidate immobilized in carbon paste electrode and the consequences for sensor construction were evaluated. The electrode showed good stability and redox properties. Two reversible redox couples with midpoint potentials between 0.15 and 0.55 V vs SCE were observed. However, peak resolution in voltammetric studies was very dependent on the supporting electrolyte. The correlation between coordinating power of the electrolyte and peak potential suggests that the electrolyte can coordinate through the axial position of the complexes. Furthermore, the axial position may be also the catalytic site, as a catalytical response was observed for hydrazine oxidation. A good linear response range for hydrazine was fit by the equation i = 23.13 (± 0.34 c , where i = current in mA and c = concentration in mol dm-3 in the range of 10-5 up to 10-2 mol dm-3. The low applied potential (<300 mV indicates a good device for hydrazine sensor, minimizing interference problems. The short response time (~1 s may be useful in flow injection analysis. Furthermore, this system was very stable presenting good repeatability even after 30 measurements with a variance of 0.5 %.

  18. Electrochemical behavior of LiCoO2 as aqueous lithium-ion battery electrodes

    KAUST Repository

    Ruffo, Riccardo

    2009-02-01

    Despite the large number of studies on the behavior of LiCoO2 in organic electrolytes and its recent application as a positive electrode in rechargeable water battery prototypes, a little information is available about the lithium intercalation reaction in this layered compound in aqueous electrolytes. This work shows that LiCoO2 electrodes can be reversibly cycled in LiNO3 aqueous electrolytes for tens of cycles at remarkably high rates with impressive values specific capacity higher than 100 mAh/g, and with a coulomb efficiency greater than 99.7%. Stable and reproducible cycling measurements have been made using a simple cell design that can be easily applied to the study of other intercalation materials, assuming that they are stable in water and that their intercalation potential range matches the electrochemical stability window of the aqueous electrolyte. The experimental arrangement uses a three-electrode flooded cell in which another insertion compound acts as a reversible source and sink of lithium ions, i.e., as the counter electrode. A commercial reference electrode is also present. Both the working and the counter electrodes have been prepared as thin layers on a metallic substrate using the procedures typical for the study of electrodes for lithium-ion batteries in organic solvent electrolytes. © 2008 Elsevier B.V. All rights reserved.

  19. Effect of covalently bonded polysiloxane multilayers on the electrochemical behavior of graphite electrode in lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Qinmin; Jiang, Yinghua [Department of Applied Chemistry, Harbin Institute of Technology, Harbin 150001 (China)

    2008-03-15

    Polysiloxane multilayers were covalently bonded to the surface of natural graphite particles via diazonium chemistry and silylation reaction. The as-prepared graphite exhibited excellent discharge-charge behavior as negative electrode materials in lithium ion batteries. The improvement in the electrochemical performance of the graphite electrodes was attributed to the formation of a stable and flexible passive film on their surfaces. It was also revealed that the chemical compositions of the multilayers exerted influence on the electrochemical behavior of the graphite electrodes. The result of this study presents a new strategy to the formation of elastic and strong passive film on the graphite electrode via molecular design. Owing to the diversity of polysilxoane multilayers, this method also enables researchers to control the surface chemistries of carbonaceous materials with flexibility. (author)

  20. Electrochemical behavior of heavily cycled nickel electrodes in Ni/H2 cells containing electrolytes of various KOH concentrations

    Science.gov (United States)

    Lim, H. S.; Verzwyvelt, S. A.

    1989-01-01

    A study has been made of charge and discharge voltage changes with cycling of Ni/H2 cells containing electrolytes of various KOH concentrations. A study has also been made of electrochemical behavior of the nickel electrodes from the cycled Ni/H2 cells as a function of overcharge amounts. Discharge voltages depressed gradually with cycling for cells having high KOH concentrations (31 to 36 percent), but the voltages increased for those having low KOH concentrations (21 to 26 percent). To determine if there was a crystallographic change of the active material due to cycling, electrochemical behavior of nickel electrodes was studied in an electrolyte flooded cell containing either 31 or 26 percent KOH electrolyte as a function of the amount of overcharge. The changes in discharge voltage appear to indicate crystal structure changes of active material from gamma-phase to beta-phase in low KOH concentrations, and vice versa in high KOH concentration.

  1. Electrochemical Behavior of Molten V2O5-K2S2O7-KHSO4 Systems

    DEFF Research Database (Denmark)

    Petrushina, Irina; Bjerrum, Niels; Berg, Rolf W.

    1997-01-01

    The electrochemical behavior of K2S2O7-KHSO4-V2O5, K2S2O7-V2O4 and K2S2O7-KHSO4-V2O4 melts was studied in argon and SO2/air atmospheres using a gold electrode. In order to identify the voltammetric waves due to KHSO4, molten KHSO4 and mixtures of K2S2O7-KHSO4 were investigated by voltammetry...

  2. Effects of zinc injection on electrochemical corrosion and cracking behavior of stainless steels in borated and lithiated high temperature water

    International Nuclear Information System (INIS)

    Wu Xinqiang; Liu Xiahe; Han Enhou; Ke Wei

    2014-01-01

    Zinc (Zn) injection water chemistry (ZWC) adopted in primary coolant system in pressurized water reactors (PWRs) is to reduce the radiation buildup as well as retard the corrosion degradation in high temperature pressurized water through improving the characteristics of oxide scales formed on components materials. However, Zn injection involved corrosion and cracking behavior and related mechanisms are still under discussion. The understanding of Zn-bearing oxide scale characteristics and their protective property is of significance to clarify the environmentally assisted material failure problems in PWRs power plants. In the present work, in-situ potentiodynamic polarization curves and electrochemical impedance spectra measurements in high temperature borated and lithiated water as well as ex-situ X-ray photoelectron spectroscopy analyses have been done to investigate the effects of temperature (R.T.-603 K), pH T value at 573 K (6.9-7.4) and Zn-injection concentration (0-150 ppb) on electrochemical corrosion behavior and oxide scale characteristics of nuclear-grade stainless steels. The protective property of oxide scales under Zn-free and Zn-injected conditions degraded with increasing temperature, with Cr-rich oxide layer playing a key role on retarding further corrosion. The composition of oxide scales appeared slightly pH T dependent: rich in chromites and ferrites at pH T =6.9 and pH T =7.4, respectively. The corrosion rate decreased significantly in the high pH T value solution with Zn injection due to the formation of thin and compact oxide scales. The ≤50 ppb Zn injection could significantly affect the formation of Zn-bearing oxides on the surfaces, while >50 ppb Zn injection showed no obvious influence on the oxide scales. A modified point defect model was proposed to discuss the effects of injected Zn concentrations on the oxide scales in high temperature water. A 10 ppb Zn injection obviously decreased the intergranular cracking susceptibility of

  3. Microstructure and electrochemical behavior of cerium conversion coating modified with silane agent on magnesium substrates

    Energy Technology Data Exchange (ETDEWEB)

    Lei, Li; Shi, Jing, E-mail: shijing@ouc.edu.cn; Wang, Xin, E-mail: wangxin.hd@163.com; Liu, Dan; Xu, Haigang

    2016-07-15

    Graphical abstract: The unmodified coating shows averaged static water contact angles of a little more than 50º, which is clearly hydrophilic for water solutions. With the silane concentration increases, the water contact angles show an increase tendency. Especially, when the silane addition is increased to 25 ml L-1, the coating surface presents a hydrophobic feature, with static water contact angle of more than 110º. - Highlights: • BTESPT modification can effectively improve the uniformity, hydrophobic performance, chemical stability and corrosion inhibition capability of traditional cerium conversion coating. • Si-O-Si linkage builds a robust structure to increase of the coating density. Si−O−Mg bonds strengthen the adhesion between the coating/substrate. • The system modified with 25 ml L{sup −1} BTESPT displays the optimum corrosion protection performance. - Abstract: The cerium conversion coating with and without different concentrations of silane agent bis-(γ-triethoxysilylpropyl)-tetrasulfide (BTESPT) modification is obtained on magnesium alloys. Detailed properties of the coatings and the role of BTESPT as an additive are studied and followed with careful discussion. The coating morphology, wettability, chemical composition and corrosion resistance are characterized by scanning electronic microscope (SEM), water contact-angle, X-ray photoelectron spectroscopy (XPS), potentiodynamic measurements and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of the coatings is investigated using EIS. The results indicate that the coating morphology and composition can be controlled by changing silane concentration. The combination of cerium ions and silane molecules could promote the formation of more homogenous and higher hydrophobic coating. The coating turns to be more compact and the adhesive strength between the coating and the magnesium substrate are strongly improved with the formation of Si−O−Si and Si

  4. Microstructure and electrochemical behavior of cerium conversion coating modified with silane agent on magnesium substrates

    International Nuclear Information System (INIS)

    Lei, Li; Shi, Jing; Wang, Xin; Liu, Dan; Xu, Haigang

    2016-01-01

    Graphical abstract: The unmodified coating shows averaged static water contact angles of a little more than 50º, which is clearly hydrophilic for water solutions. With the silane concentration increases, the water contact angles show an increase tendency. Especially, when the silane addition is increased to 25 ml L-1, the coating surface presents a hydrophobic feature, with static water contact angle of more than 110º. - Highlights: • BTESPT modification can effectively improve the uniformity, hydrophobic performance, chemical stability and corrosion inhibition capability of traditional cerium conversion coating. • Si-O-Si linkage builds a robust structure to increase of the coating density. Si−O−Mg bonds strengthen the adhesion between the coating/substrate. • The system modified with 25 ml L"−"1 BTESPT displays the optimum corrosion protection performance. - Abstract: The cerium conversion coating with and without different concentrations of silane agent bis-(γ-triethoxysilylpropyl)-tetrasulfide (BTESPT) modification is obtained on magnesium alloys. Detailed properties of the coatings and the role of BTESPT as an additive are studied and followed with careful discussion. The coating morphology, wettability, chemical composition and corrosion resistance are characterized by scanning electronic microscope (SEM), water contact-angle, X-ray photoelectron spectroscopy (XPS), potentiodynamic measurements and electrochemical impedance spectroscopy (EIS). The electrochemical behavior of the coatings is investigated using EIS. The results indicate that the coating morphology and composition can be controlled by changing silane concentration. The combination of cerium ions and silane molecules could promote the formation of more homogenous and higher hydrophobic coating. The coating turns to be more compact and the adhesive strength between the coating and the magnesium substrate are strongly improved with the formation of Si−O−Si and Si−O−M chemical

  5. The electrochemical behavior of cobalt phthalocyanine/platinum as methanol-resistant oxygen-reduction electrocatalysts for DMFC

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yuhao; Reddy, Ramana G. [Department of Metallurgical and Materials Engineering, The University of Alabama, P.O. Box 870202, Tuscaloosa, AL 35487 (United States)

    2007-02-01

    The electrochemical behavior of cobalt phthalocyanine/platinum as methanol-resistant oxygen-reduction electrocatalyst for DMFC was investigated. Platinum was chemically deposited on the carbon-supported cobalt phthalocyanine (CoPc), and then it was heat-treated in high purity nitrogen at 300 C, 635 C and 980 C. In order to evaluate the electrocatalytic behavior of CoPc-Pt/C, the PtCo/C and Pt/C as reference catalysts were employed. TGA, XRD, EDAX, XPS and electrochemical experiments were used to study the thermal stability, crystal structure, physical characterization and electrochemical behavior of these catalysts. These catalysts exhibited similar electrocatalytic activity for oxygen reaction in 0.5 M H{sub 2}SO{sub 4} solution. In methanol tolerance experiments, Pt/C, PtCo/C and CoPc-Pt/C heated at 980 C were active for the methanol oxidation reaction (MOR). The presence of Co did not improve resistance to methanol poisoning. However, the CoPc-Pt/C after 300 C or 635 C heat-treatment demonstrated significant inactivity for MOR, hence they have a good ability to resist methanol poisoning. The current study indicated that the macrocyclic structure of phthalocyanine is the most important factor to improve the methanol tolerance of CoPc-Pt/C as the oxygen-reduction reaction (ORR) electrocatalyst. The CoPc-Pt based catalyst should be a good alternation for oxygen electro-reduction reaction in DMFC. (author)

  6. Electrochemical behavior of antioxidants: Part 3. Electrochemical studies of caffeic Acid–DNA interaction and DNA/carbon nanotube biosensor for DNA damage and protection

    Directory of Open Access Journals (Sweden)

    Refat Abdel-Hamid

    2016-05-01

    Full Text Available Multi-walled carbon nanotubes-modified glassy carbon electrode biosensor was used for electrochemical studies of caffeic acid–dsDNA interaction in phosphate buffer solution at pH 2.12. Caffeic acid, CAF, shows a well-defined cyclic voltammetric wave. Its anodic peak current decreases and the peak potential shifts positively on the addition of dsDNA. This behavior was ascribed to an interaction of CAF with dsDNA giving CAF–dsDNA complex by intercalative binding mode. The apparent binding constant of CAF–dsDNA complex was determined using amperometric titrations. The oxidative damage caused to DNA was detected using the biosensor. The damage caused by the reactive oxygen species, hydroxyl radical (·−OH generated by the Fenton system on the DNA-biosensor was detected. It was found that CAF has the capability of scavenging the hydroxide radical and protecting the DNA immobilized on the GCE surface.

  7. Coupling of Mechanical Behavior of Lithium Ion Cells to Electrochemical-Thermal (ECT) Models for Battery Crush

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Chao; Santhanagopalan, Shriram; Pesaran, Ahmad; Sahraei, Elham; Wierzbicki, Tom

    2016-06-14

    Vehicle crashes can lead to crushing of the battery, damaging lithium ion battery cells and causing local shorts, heat generation, and thermal runaway. Simulating all the physics and geometries at the same time is challenging and takes a lot of effort; thus, simplifications are needed. We developed a material model for simultaneously modeling the mechanical-electrochemical-thermal behavior, which predicted the electrical short, voltage drop, and thermal runaway behaviors followed by a mechanical abuse-induced short. The effect of short resistance on the battery cell performance was studied.

  8. Electrochemical behavior of hydroxyapatite/TiN multi-layer coatings on Ti alloys

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Eun-Ju [Department of Dental Materials, Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University (Korea, Republic of); Jeong, Yong-Hoon [Biomechanics and Tissue Engineering Laboratory, Division of Orthodontics, College of Dentistry, The Ohio State University, Columbus, OH (United States); Choe, Han-Cheol, E-mail: hcchoe@chosun.ac.kr [Department of Dental Materials, Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University (Korea, Republic of); Brantley, William A. [Division of Restorative Science and Prosthodontics, College of Dentistry, The Ohio State University, Columbus, OH (United States)

    2014-12-01

    The electrochemical behavior of hydroxyapatite (HA) and titanium nitride (TiN) multi-layer coatings on Ti–Nb–Zr alloys was investigated by a variety of surface analytical methods. The HA/TiN layers were deposited using a magnetron sputtering system. The HA target was made of human tooth-ash sintered at 1300 °C for 1 h and had an average Ca/P ratio of 1.9. From X-ray diffraction patterns, the Ti–29Nb–5Zr alloy was composed entirely of equiaxed β-phase exhibiting the principal (110) reflection, and the coating exhibited the (111) and (200) reflections for TiN and the (112) and (202) reflections for HA. At the coating surface the HA films consisted of granular particles, and the surface roughness was 4.22 nm. The thickness of the coating layers increased in the order of HA/TiN (lowest), TiN, and HA (highest). Potentiodynamic polarization measurements revealed that the corrosion current density was the lowest, and the corrosion potential and polarization resistance the highest, when the Ti–29Nb–5Zr surface was covered by the HA/TiN film, compared to solely HA or TiN films. - Highlights: • HA/TiN films were deposited by magnetron sputtering on a Ti–29Nb–5Zr biomedical alloy. • The corrosion current density for the HA/TiN films was lower than that of the non-coated alloy. • The polarization resistance of the HA/TiN films was higher than that of the non-coated alloy.

  9. Electrochemical behavior of hydroxyapatite/TiN multi-layer coatings on Ti alloys

    International Nuclear Information System (INIS)

    Kim, Eun-Ju; Jeong, Yong-Hoon; Choe, Han-Cheol; Brantley, William A.

    2014-01-01

    The electrochemical behavior of hydroxyapatite (HA) and titanium nitride (TiN) multi-layer coatings on Ti–Nb–Zr alloys was investigated by a variety of surface analytical methods. The HA/TiN layers were deposited using a magnetron sputtering system. The HA target was made of human tooth-ash sintered at 1300 °C for 1 h and had an average Ca/P ratio of 1.9. From X-ray diffraction patterns, the Ti–29Nb–5Zr alloy was composed entirely of equiaxed β-phase exhibiting the principal (110) reflection, and the coating exhibited the (111) and (200) reflections for TiN and the (112) and (202) reflections for HA. At the coating surface the HA films consisted of granular particles, and the surface roughness was 4.22 nm. The thickness of the coating layers increased in the order of HA/TiN (lowest), TiN, and HA (highest). Potentiodynamic polarization measurements revealed that the corrosion current density was the lowest, and the corrosion potential and polarization resistance the highest, when the Ti–29Nb–5Zr surface was covered by the HA/TiN film, compared to solely HA or TiN films. - Highlights: • HA/TiN films were deposited by magnetron sputtering on a Ti–29Nb–5Zr biomedical alloy. • The corrosion current density for the HA/TiN films was lower than that of the non-coated alloy. • The polarization resistance of the HA/TiN films was higher than that of the non-coated alloy

  10. Effects of Anion Mobility on Electrochemical Behaviors of Lithium–Sulfur Batteries

    Energy Technology Data Exchange (ETDEWEB)

    Han, Kee Sung; Chen, Junzheng; Cao, Ruiguo; Rajput, Nav Nidhi; Murugesan, Vijayakumar; Shi, Lili; Pan, Huilin; Zhang, Jiguang; Liu, Jun; Persson, Kristin A.; Mueller, Karl T.

    2017-10-27

    The electrolyte is a crucial component of lithium-sulfur (Li-S) batteries, as it controls polysulfide dissolution, charge shuttling processes, and solid-electrolyte interphase (SEI) layer formation. Experimentally, the overall performance of Li-S batteries varies with choice of solvent system and Li-salt used in the electrolyte, and a lack of predictive understanding about the effects of individual electrolyte components inhibits the rational design of electrolytes for Li-S batteries. Here we analyze the role of the counter anions of common Li salts (such as TfO-, FSI-, TFSI-, and TDI-) when dissolved in DOL/DME (1:1 vol.) for use in Li-S batteries. The evolution of ion-ion and ion-solvent interactions due to vari-ous anions was analyzed using 17O NMR and pulsed-field gradient (PFG) NMR and then correlated with electrochemi-cal performance in Li-S cells. These data reveal that the for-mation of the passivation layer on the anode and the loss of active materials from the cathode (evidenced by polysulfide dissolution) are related to anion mobility and affinity with lithium polysulfide, respectively. For future electrolyte de-sign, anions with lower mobility and weaker interactions with lithium polysulfides may be superior candidates for increasing the long-term stability of Li-S batteries.

  11. Application of ionic liquids as an electrolyte additive on the electrochemical behavior of lead acid battery

    Energy Technology Data Exchange (ETDEWEB)

    Rezaei, Behzad; Mallakpour, Shadpour; Taki, Mahmood [Department of Chemistry, Isfahan University of Technology, Isfahan 84156-83111 (Iran)

    2009-02-15

    Ionic liquids (ILs) belong to new branch of salts with unique properties which their applications have been increasing in electrochemical systems especially lithium-ion batteries. In the present work, for the first time, the effects of four ionic liquids as an electrolyte additive in battery's electrolyte were studied on the hydrogen and oxygen evolution overpotential and anodic layer formation on lead-antimony-tin grid alloy of lead acid battery. Cyclic and linear sweep voltammetric methods were used for this study in aqueous sulfuric acid solution. The morphology of grid surface after cyclic redox reaction was studied using scanning electron microscopy. The results show that most of added ionic liquids increase hydrogen overpotential and whereas they have no significant effect on oxygen overpotential. Furthermore ionic liquids increase antimony dissolution that might be related to interaction between Sb{sup 3+} and ionic liquids. Crystalline structure of PbSO{sub 4} layer changed with presence of ionic liquids and larger PbSO{sub 4} crystals were formed with some of them. These additives decrease the porosity of PbSO{sub 4} perm selective membrane layer at the surface of electrode. Also cyclic voltammogram on carbon-PbO paste electrode shows that with the presence of ionic liquids, oxidation and reduction peak current intensively increased. (author)

  12. A study on electrochemical redox behavior of nitric acid by using a glassy carbon fiber column electrode system

    International Nuclear Information System (INIS)

    Kim, K. W.; Song, K. C.; Lee, I. H.; Choi, I. K.; You, J. H.

    1999-01-01

    Electrochemical redox behaviors of nitric acid were studied by using a glassy carbon fiber column electrode system, and its reaction mechanism was analyzed in several ways. The electrochemical reaction in less than 2.0 M nitric acid was not observed, but in more than 2.0 M nitric acid, the reduction rate of nitric acid to produce nitrous acid was slow so that the nitric acid solution had to be contacted with electrode enough in order for a apparent reduction current of nitric acid to nitrous acid be to observed. The nitrous acid generated in more than 2.0 M nitric acid was rapidly and easily reduced to NOx through an autocatalytic reaction. Sulfamic acid was confirmed to be effective to destroy the nitrous acid. The sulfamic acid of at least 0.05M was necessary to remove the nitrous acid generated in 3.5 M nitric acid

  13. Investigation of Physical Properties and Electrochemical Behavior of Nitrogen-Doped Diamond-Like Carbon Thin Films

    Directory of Open Access Journals (Sweden)

    Rattanakorn Saensak

    2014-03-01

    Full Text Available This work reports characterizations of diamond-like carbon (DLC films used as electrodes for electrochemical applications. DLC thin films are prepared on glass slides and silicon substrates by radio frequency plasma enhanced chemical vapor deposition (RF-PECVD using a gas mixture of methane and hydrogen. In addition, the DLC films are doped with nitrogen in order to reduce electrical resistivity. Compared to the undoped DLC films, the electrical resistivity of nitrogen-doped (N-doped DLC films is decreased by three orders of magnitude. Raman spectroscopy and UV/Vis spectroscopy analyses show the structural transformation in N-doped DLC films that causes the reduction of band gap energy. Contact angle measurement at N-doped DLC films indicates increased hydrophobicity. The results obtained from the cyclic voltammetry measurements with Fe(CN63-/Fe(CN64- redox species exhibit the correlation between the physical properties and electrochemical behavior of DLC films.

  14. Electrochemical Characteristics of Layered Transition Metal Oxide Cathode Materials for Lithium Ion Batteries: Surface, Bulk Behavior, and Thermal Properties.

    Science.gov (United States)

    Tian, Chixia; Lin, Feng; Doeff, Marca M

    2018-01-16

    Layered lithium transition metal oxides, in particular, NMCs (LiNi x Co y Mn z O 2 ) represent a family of prominent lithium ion battery cathode materials with the potential to increase energy densities and lifetime, reduce costs, and improve safety for electric vehicles and grid storage. Our work has focused on various strategies to improve performance and to understand the limitations to these strategies, which include altering compositions, utilizing cation substitutions, and charging to higher than usual potentials in cells. Understanding the effects of these strategies on surface and bulk behavior and correlating structure-performance relationships advance our understanding of NMC materials. This also provides information relevant to the efficacy of various approaches toward ensuring reliable operation of these materials in batteries intended for demanding traction and grid storage applications. In this Account, we start by comparing NMCs to the isostructural LiCoO 2 cathode, which is widely used in consumer batteries. Effects of changing the metal content (Ni, Mn, Co) upon structure and performance of NMCs are briefly discussed. Our early work on the effects of partial substitution of Al, Fe, and Ti for Co on the electrochemical and bulk structural properties is then covered. The original aim of this work was to reduce the Co content (and thus the raw materials cost) and to determine the effect of the substitutions on the electrochemical and bulk structural properties. More recently, we have turned to the application of synchrotron and advanced microscopy techniques to understand both bulk and surface characteristics of the NMCs. Via nanoscale-to-macroscale spectroscopy and atomically resolved imaging techniques, we were able to determine that the surfaces of NMC undergo heterogeneous reconstruction from a layered structure to rock salt under a variety of conditions. Interestingly, formation of rock salt also occurs under abuse conditions. The surface

  15. Origin of the different behavior of some platinum decorated nanocarbons towards the electrochemical oxidation of hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Malara, A. [Dipartimento di Ingegneria dell' Informazione, delle Infrastrutture e dell' Energia Sostenibile (DIIES), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Leonardi, S.G.; Bonavita, A. [Dipartimento di Ingegneria Elettronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Fazio, E. [Dipartimento di Scienze Matematiche e Informatiche, Scienze Fisiche e Scienze della Terra (MIFT), Università di Messina, 98166 Messina (Italy); Stelitano, S. [Dipartimento di Fisica (DF), Università della Calabria, 87036 Arcavacata di Rende (Italy); Neri, G. [Dipartimento di Ingegneria Elettronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Neri, F. [Dipartimento di Scienze Matematiche e Informatiche, Scienze Fisiche e Scienze della Terra (MIFT), Università di Messina, 98166 Messina (Italy); Santangelo, S., E-mail: saveria.santangelo@unirc.it [Dipartimento di Ingegneria Civile, dell' Energia, dell' Ambiente e dei Materiali (DICEAM), Università “Mediterranea”, 89122 Reggio Calabria (Italy)

    2016-12-01

    The electrochemical behavior of different platinum-decorated nanocarbons (Pt@C) towards the oxidation of hydrogen peroxide (H{sub 2}O{sub 2}) was investigated. Three different types of nanocarbons were considered: i) carbon black, ii) dahlia-like carbon nanohorns and iii) carbon nanotubes, which included both commercial (single-wall and multi-wall) and laboratory prepared (multi-wall) samples. Shape and size distribution of the platinum nanoparticles and morphology of the nanocarbons were analyzed by transmission electron microscopy. Their nanostructure was investigated by micro-Raman spectroscopy, while elemental composition of the samples and chemical bonding states were studied by X-ray photoelectron spectroscopy. Electrochemical behavior towards H{sub 2}O{sub 2} oxidation was evaluated by means of cyclic voltammetry modifying the working screen-printed carbon electrode surface with the prepared Pt@C nanocomposites. Data obtained suggest that the size and dispersion of the Pt nanoparticles play a key role in increasing the sensitivity towards H{sub 2}O{sub 2} detection. Thanks to the presence of smaller and more dispersed platinum particles and of a greater amount of platinum hydroxide, acting as intermediary in the H{sub 2}O{sub 2} oxidation process, Pt@dahlia-like carbon nanohorns result to be the most promising platform for the development of H{sub 2}O{sub 2} electrochemical sensors. - Highlights: • Different nanocarbons are decorated with Pt nanoparticles by wet impregnation method. • Pt@C-based hybrids are tested as active materials for sensing of hydrogen peroxide. • Sensor based on Pt@dahlia-like carbon nanohorns is the most performing device. • The origin of the different electrochemical behaviour is investigated. • Pt@C sensing performances are correlated with their structural and surface properties.

  16. Origin of the different behavior of some platinum decorated nanocarbons towards the electrochemical oxidation of hydrogen peroxide

    International Nuclear Information System (INIS)

    Malara, A.; Leonardi, S.G.; Bonavita, A.; Fazio, E.; Stelitano, S.; Neri, G.; Neri, F.; Santangelo, S.

    2016-01-01

    The electrochemical behavior of different platinum-decorated nanocarbons (Pt@C) towards the oxidation of hydrogen peroxide (H_2O_2) was investigated. Three different types of nanocarbons were considered: i) carbon black, ii) dahlia-like carbon nanohorns and iii) carbon nanotubes, which included both commercial (single-wall and multi-wall) and laboratory prepared (multi-wall) samples. Shape and size distribution of the platinum nanoparticles and morphology of the nanocarbons were analyzed by transmission electron microscopy. Their nanostructure was investigated by micro-Raman spectroscopy, while elemental composition of the samples and chemical bonding states were studied by X-ray photoelectron spectroscopy. Electrochemical behavior towards H_2O_2 oxidation was evaluated by means of cyclic voltammetry modifying the working screen-printed carbon electrode surface with the prepared Pt@C nanocomposites. Data obtained suggest that the size and dispersion of the Pt nanoparticles play a key role in increasing the sensitivity towards H_2O_2 detection. Thanks to the presence of smaller and more dispersed platinum particles and of a greater amount of platinum hydroxide, acting as intermediary in the H_2O_2 oxidation process, Pt@dahlia-like carbon nanohorns result to be the most promising platform for the development of H_2O_2 electrochemical sensors. - Highlights: • Different nanocarbons are decorated with Pt nanoparticles by wet impregnation method. • Pt@C-based hybrids are tested as active materials for sensing of hydrogen peroxide. • Sensor based on Pt@dahlia-like carbon nanohorns is the most performing device. • The origin of the different electrochemical behaviour is investigated. • Pt@C sensing performances are correlated with their structural and surface properties.

  17. Multiple performance optimization of electrochemical drilling of Inconel 625 using Taguchi based Grey Relational Analysis

    Directory of Open Access Journals (Sweden)

    N. Manikandan

    2017-04-01

    Full Text Available In this present investigation, a multi performance characteristics optimization based on Taguchi approach with Grey Relational Analysis (GRA is proposed for Electrochemical Drilling process on Inconel 625 material which is used for marine, nuclear, aerospace applications, especially in corrosive environments. Experimental runs have been planned as per Taguchi’s principle with three input machining variables such as feed rate, flow rate of electrolyte and concentration of electrolyte. Besides the material removal rate and surface roughness, the geometric measures such as overcut, form and orientation tolerance are included as performance measures in this investigation. Outcomes of the analysis show that the feed rate is the predominant variable for the desired performance characteristics. On establishing the desired performance measures and multiple regression models are developed to be used as predictive tools. The confirmation test also conducted to validate the results attained by GRA approach and affirmed that there is considerable improvement with the help of proposed approach.

  18. The Challenge of Electrochemical Ammonia Synthesis: A New Perspective on the Role of Nitrogen Scaling Relations.

    Science.gov (United States)

    Montoya, Joseph H; Tsai, Charlie; Vojvodic, Aleksandra; Nørskov, Jens K

    2015-07-08

    The electrochemical production of NH3 under ambient conditions represents an attractive prospect for sustainable agriculture, but electrocatalysts that selectively reduce N2 to NH3 remain elusive. In this work, we present insights from DFT calculations that describe limitations on the low-temperature electrocatalytic production of NH3 from N2 . In particular, we highlight the linear scaling relations of the adsorption energies of intermediates that can be used to model the overpotential requirements in this process. By using a two-variable description of the theoretical overpotential, we identify fundamental limitations on N2 reduction analogous to those present in processes such as oxygen evolution. Using these trends, we propose new strategies for catalyst design that may help guide the search for an electrocatalyst that can achieve selective N2 reduction. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Zinc-based electrolyte compositions, and related electrochemical processes and articles

    Science.gov (United States)

    Kniajanski, Sergei; Soloveichik, Grigorii Lev

    2018-02-20

    An aqueous electrolyte composition is described, including a zinc salt based on zinc acetate or zinc glocolate. The saturation concentration of zinc in the electrolyte composition is in the range of about 2.5M to about 3.5M. The composition also contains at least one salt of a monovalent cation. The molar ratio of zinc to the monovalent cation is about 1:2. An aqueous zinc electroplating bath, containing the aqueous electrolyte composition, is also disclosed, along with a method for the electrochemical deposition of zinc onto a substrate surface, using the electroplating bath. Related flow batteries are also described, including a catholyte, as well as an anolyte based on the aqueous electrolyte composition, with a membrane between the catholyte and the anolyte.

  20. Promising and Reversible Electrolyte with Thermal Switching Behavior for Safer Electrochemical Storage Devices.

    Science.gov (United States)

    Shi, Yunhui; Zhang, Qian; Zhang, Yan; Jia, Limin; Xu, Xinhua

    2018-02-28

    A major stumbling block in large-scale adoption of high-energy-density electrochemical devices has been safety issues. Methods to control thermal runaway are limited by providing a one-time thermal protection. Herein, we developed a simple and reversible thermoresponsive electrolyte system that is efficient to shutdown the current flow according to temperature changes. The thermal management is ascribed to the thermally activated sol-gel transition of methyl cellulose solution, associated with the concentration of ions that can move between isolated chains freely or be restricted by entangled molecular chains. We studied the effect of cellulose concentration, substituent types, and operating temperature on the electrochemical performance, demonstrating an obvious capacity loss up to 90% approximately of its initial value. Moreover, this is a cost-effective approach that has the potential for use in practical electrochemical storage devices.

  1. International Relations: Understanding the Behavior of Nations.

    Science.gov (United States)

    Zack, David R.; And Others

    In today's world, no nation acts in isolation; the interdependence of nations makes international relations complex and ever-changing. This book is designed to help students understand why nations compete, why they cooperate, and why they sometimes go to war. Chapter 1 examines the behavior of nations and how national interest dictates the…

  2. Electrochemical behavior of free-radical derivatives of tetra(4hydroxyl-3,5-di-tert-butylphenyl) porphyrin

    Energy Technology Data Exchange (ETDEWEB)

    Pokhodenko, V.D.; Melezhik, A.V.; Platonova, E.P.; Vovk, D.N.

    1984-08-01

    The electrochemical behavior of free-radical derivatives of tetra(4hydroxyl-3,5-di-tert-butylphenyl) porphyrins and their complexes with Mg(II), Zn(II), Ni(II), CU(II), and Pd(II) ions was studied by the methods of voltamperometry, ESR, and spectrophotometry. It was shown that the introduction of free-radical substituents into the porphin macrocycle leads to a substantial decrease in the oxidation and reduction potentials of the complexes. The degree of conjunction of substituents with the porphin macrocycle is estimated according to the difference of the redox potentials of free-radical and quinoid derivatives of metalloporphyrins.

  3. Corrosion-electrochemical behavior of nickel in an alkali metal carbonate melt under a chlorine-containing atmosphere

    Science.gov (United States)

    Nikitina, E. V.; Kudyakov, V. Ya.; Malkov, V. B.; Plaksin, S. V.

    2013-08-01

    The corrosion-electrochemical behavior of a nickel electrode is studied in the melt of lithium, sodium, and potassium (40: 30: 30 mol %) carbonates in the temperature range 500-600°C under an oxidizing atmosphere CO2 + 0.5O2 (2: 1), which is partly replaced by gaseous chlorine (30, 50, 70%) in some experiments. In other experiments, up to 5 wt % chloride of sodium peroxide is introduced in a salt melt. A change in the gas-phase composition is shown to affect the mechanism of nickel corrosion.

  4. Effect of Different Welding Processes on Electrochemical and Corrosion Behavior of Pure Nickel in 1 M NaCl Solution

    Directory of Open Access Journals (Sweden)

    Xijing Wang

    2017-11-01

    Full Text Available A plasma arc welding (PAW-tungsten inert gas (TIG hybrid welding process is proposed to weld pure nickel. In PAW-TIG welding, the arc of the PAW was first to be ignited, then TIG was ignited, while in PAW welding, only the PAW arc was launched. This paper investigated the effect of different welding processes on electrochemical and corrosion performance of between a pure nickel joint and a base metal in an aerated 1 M NaCl solution, respectively. The average grain size of the joint fabricated by PAW welding (denoted as JP joint is 463.57 μm, the joint fabricated by PAW-TIG welding(denoted as JP-T joint is 547.32 μm, and the base metal (BM is 47.32 μm. In this work, the passivity behaviors of samples were characterized for two welding processes by electrochemical impedance spectroscopy (EIS, open circuit potential versus immersion time (OCP-t, and the potentiodynamic polarization plots. EIS spectra, attained with different immersion times, were analyzed and fitted by an equivalent electrical circuit. Photomicrographs of BM, JP, and JP-T were also taken with a scanning electron microscope (SEM to reveal the morphological structure of the pit surfaces. Electrochemical tests show that the sequence of the corrosion resistance is BM > JP > JP-T. The size and quantity of the hemispherical corrosion pits of all samples are different. The corrosion morphology observations found a consistency with the consequence of the electrochemical measurements. The results show that an increase of the grain dimensions due to different heat treatments decreased the pure nickel stability to pitting corrosion.

  5. Neuroimaging for drug addiction and related behaviors

    International Nuclear Information System (INIS)

    Parvaz, M.A.; Alia-Klein, N.; Woicik, P.A.; Volkow, N.D.; Goldstein, R.Z.

    2011-01-01

    In this review, we highlight the role of neuroimaging techniques in studying the emotional and cognitive-behavioral components of the addiction syndrome by focusing on the neural substrates subserving them. The phenomenology of drug addiction can be characterized by a recurrent pattern of subjective experiences that includes drug intoxication, craving, bingeing, and withdrawal with the cycle culminating in a persistent preoccupation with obtaining, consuming, and recovering from the drug. In the past two decades, imaging studies of drug addiction have demonstrated deficits in brain circuits related to reward and impulsivity. The current review focuses on studies employing positron emission tomography (PET), functional magnetic resonance imaging (fMRI), and electroencephalography (EEG) to investigate these behaviors in drug-addicted human populations. We begin with a brief account of drug addiction followed by a technical account of each of these imaging modalities. We then discuss how these techniques have uniquely contributed to a deeper understanding of addictive behaviors.

  6. Neuroimaging for drug addiction and related behaviors

    Energy Technology Data Exchange (ETDEWEB)

    Parvaz M. A.; Parvaz, M.A.; Alia-Klein, N.; Woicik,P.A.; Volkow, N.D.; Goldstein, R.Z.

    2011-10-01

    In this review, we highlight the role of neuroimaging techniques in studying the emotional and cognitive-behavioral components of the addiction syndrome by focusing on the neural substrates subserving them. The phenomenology of drug addiction can be characterized by a recurrent pattern of subjective experiences that includes drug intoxication, craving, bingeing, and withdrawal with the cycle culminating in a persistent preoccupation with obtaining, consuming, and recovering from the drug. In the past two decades, imaging studies of drug addiction have demonstrated deficits in brain circuits related to reward and impulsivity. The current review focuses on studies employing positron emission tomography (PET), functional magnetic resonance imaging (fMRI), and electroencephalography (EEG) to investigate these behaviors in drug-addicted human populations. We begin with a brief account of drug addiction followed by a technical account of each of these imaging modalities. We then discuss how these techniques have uniquely contributed to a deeper understanding of addictive behaviors.

  7. Facile fabrication and electrochemical behaviors of Mn:ZnS nanocrystals

    International Nuclear Information System (INIS)

    Xie, Ruishi; Li, Yuanli; Liu, Haifeng; Guo, Baogang

    2016-01-01

    Here, we demonstrate the rational design and synthesis of Mn:ZnS nanocrystals with adjustable doping concentrations utilizing a facile, cost effective, and environmentally benign chemical protocol. These nanostructures were investigated as electrode materials for lithium-ion batteries. Compared with pristine ZnS nanocrystals, the Mn:ZnS nanocrystals exhibit significantly improved electrochemical performances in terms of specific capacity and cycling performance. The Mn:ZnS nanocrystal sample with doping concentration of 1 at% displays second discharge capacity of 789.9 mA h g"−"1 at a current density of 24 mA g"−"1, about 2.39 times higher than that of the pure ZnS nanocrystal. Furthermore, the Mn:ZnS nanocrystal electrodes represent much better capacity retention than that of the undoped one. The greatly improved electrochemical performances of the Mn:ZnS nanocrystal samples could be attributed to the following factors. The large specific surface area can significantly enhance structural integrity by acting as mechanical buffer, effectively alleviating the volume changes generated during the lithiation/delithiation process. The incorporation of Mn into the lattice of ZnS improves charge transfer kinetics and results in a faster Li"+ diffusion rate during the charge–discharge process. It is of great significance to incorporate guest metal ions into nanostructured materials to display especial electrochemical characteristics triggering an effective approach to improve the electrochemical properties.

  8. Electrochemical behavior of an anticancer drug 5-fluorouracil at methylene blue modified carbon paste electrode

    International Nuclear Information System (INIS)

    Bukkitgar, Shikandar D.; Shetti, Nagaraj P.

    2016-01-01

    A novel sensor for the determination of 5-fluorouracil was constructed by electrochemical deposition of methylene blue on surface of carbon paste electrode. The electrode surface morphology was studied using Atomic force microscopy and XRD. The electrochemical activity of modified electrode was characterized using cyclic voltammetry and differential pulse method. The developed sensor shows impressive enlargement in sensitivity of 5-fluorouracil determination. The peak currents obtained from differential pulse voltammetry was linear with concentration of 5-fluorouracil in the range 4 × 10 −5 –1 × 10 −7 M and detection limit and quantification limit were calculated to be 2.04 nM and 6.18 nM respectively. Further, the sensor was successfully applied in pharmaceutical and biological fluid sample analysis. - Highlights: • Electrochemical oxidation of 5-fluorouracil has been investigated for first time at methylene blue modified carbon paste electrode • The electrode process was irreversible and diffusion controlled • Probable electrochemical mechanism was proposed which involved two proton and two electron transfer reaction • The LOD and LOQ values were calculated to be 2.04 nM and 6.18 nM, respectively, with good selectivity and sensitivity. • Proposed method was applied to 5-Fluorouracil determination in pharmaceutical and spiked human urine samples

  9. Electrochemical behavior of boron in LiF-NaF-KF- melts

    DEFF Research Database (Denmark)

    Polyakova, L.P.; Bukatova, G.A.; Polyakova, E.G.

    1996-01-01

    The electrochemical reduction of B(III) to B(0) in KBF4-LiF-NaF-KF melts has been studied by voltammetric and chronopotentiometric methods, Glassy carbon, Pt, and Ag were used as working electrode materials. Only in the case of Ag was the reduction not complicated by interaction between boron...

  10. Facile fabrication and electrochemical behaviors of Mn:ZnS nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Xie, Ruishi [Analytical and Testing Center, Southwest University of Science and Technology, Mianyang, 621010 (China); Li, Yuanli, E-mail: yuanlyl@foxmail.com [Department of Materials, Southwest University of Science and Technology, Mianyang, 621010 (China); Liu, Haifeng; Guo, Baogang [Analytical and Testing Center, Southwest University of Science and Technology, Mianyang, 621010 (China)

    2016-07-05

    Here, we demonstrate the rational design and synthesis of Mn:ZnS nanocrystals with adjustable doping concentrations utilizing a facile, cost effective, and environmentally benign chemical protocol. These nanostructures were investigated as electrode materials for lithium-ion batteries. Compared with pristine ZnS nanocrystals, the Mn:ZnS nanocrystals exhibit significantly improved electrochemical performances in terms of specific capacity and cycling performance. The Mn:ZnS nanocrystal sample with doping concentration of 1 at% displays second discharge capacity of 789.9 mA h g{sup −1} at a current density of 24 mA g{sup −1}, about 2.39 times higher than that of the pure ZnS nanocrystal. Furthermore, the Mn:ZnS nanocrystal electrodes represent much better capacity retention than that of the undoped one. The greatly improved electrochemical performances of the Mn:ZnS nanocrystal samples could be attributed to the following factors. The large specific surface area can significantly enhance structural integrity by acting as mechanical buffer, effectively alleviating the volume changes generated during the lithiation/delithiation process. The incorporation of Mn into the lattice of ZnS improves charge transfer kinetics and results in a faster Li{sup +} diffusion rate during the charge–discharge process. It is of great significance to incorporate guest metal ions into nanostructured materials to display especial electrochemical characteristics triggering an effective approach to improve the electrochemical properties.

  11. Behavioral symptoms related to cognitive impairment

    Directory of Open Access Journals (Sweden)

    Dillon C

    2013-09-01

    Full Text Available Carol Dillon,1 Cecilia M Serrano,1 Diego Castro,1 Patricio Perez Leguizamón,1 Silvina L Heisecke,1,2 Fernando E Taragano1 1CEMIC (Centro de Educación Médica e Investigaciones Clínicas University Institute, 2CONICET (Consejo Nacional de Investigaciones Cientificas y Técnicas, Buenos Aires, Argentina Abstract: Neuropsychiatric symptoms (NPS are core features of Alzheimer's disease and related dementias. On one hand, behavioral symptoms in patients with mild cognitive impairment (MCI can indicate an increased risk of progressing to dementia. On the other hand, mild behavioral impairment (MBI in patients who usually have normal cognition indicates an increased risk of developing dementia. Whatever the cause, all dementias carry a high rate of NPI. These symptoms can be observed at any stage of the disease, may fluctuate over its course, are a leading cause of stress and overload for caregivers, and increase rates of hospitalization and early institutionalization for patients with dementia. The clinician should be able to promptly recognize NPI through the use of instruments capable of measuring their frequency and severity to support diagnosis, and to help monitor the treatment of behavioral symptoms. The aims of this review are to describe and update the construct ‘MBI’ and to revise the reported NPS related to prodromal stages of dementia (MCI and MBI and dementia stages of Alzheimer’s disease and frontotemporal lobar degeneration. Keywords: behavioral or neuropsychiatric symptoms, cognitive impairment, dementia

  12. Perceptions of Popularity-Related Behaviors in the Cyber Context: Relations to Cyber Social Behaviors

    Directory of Open Access Journals (Sweden)

    Michelle F. Wright

    2015-01-01

    Full Text Available Despite acknowledging that adolescents are active users of electronic technology, little is known about their perceptions concerning how such technologies might be used to promote their social standing among their peer group and whether these perceptions relate to their cyber social behaviors (i.e., cyber aggression perpetration, cyber prosocial behavior. To address this gap in the literature, the present study included 857 seventh graders (M age: 12.19; 50.8% female from a large Midwestern city in the United States. They completed questionnaires on face-to-face social behaviors, cyber social behaviors, perceived popularity, social preference, and their perceptions of characteristics and activities related to the cyber context which might be used to promote popularity. Findings revealed four activities and characteristics used to improve adolescents’ social standing in the peer group, including antisocial behaviors, sociability, prosocial behaviors, and technology access. Using antisocial behaviors in the cyber context to promote popularity was related to cyber aggression perpetration, while controlling for gender, social preference, and perceived popularity. On the other hand, sociability and prosocial behaviors in the cyber context used to improve popularity as well as technology access were associated with cyber prosocial behavior. A call for additional research is made.

  13. Electrochemical behavior of gold (III) in cyanide-free bath with 5,5′-dimethylhydantoin as complexing agent

    International Nuclear Information System (INIS)

    Yang Xiaowei; An Maozhong; Zhang Yunwang; Zhang Lin

    2011-01-01

    Highlights: ► The DMH gold plating electrolyte with good stability studied in this paper is cyanide-free and the influence of novel additive (pyridyl-compound) on the nucleation and growth of gold is also investigated. ► The electrochemical behavior of gold electrodeposition in DMH bath is firstly analyzed using cyclic voltammograms and chronoamperometry techniques. - Abstract: Gold electrodeposits are prepared in a cyanide-free bath with 5,5′-dimethylhydantoin (DMH) as complexing agent. The electrochemical behavior of the electrodeposition is then investigated together with the influence of additive A (pyridyl-compound) as an additive on the nucleation and growth of gold using electrochemical techniques on gold working electrode at different temperatures. Cyclic voltammogram consists of a single cathodic reduction wave at −0.62 V which corresponds to the reduction of Au(III) to Au without anodic oxidation wave observed. The diffusion coefficient of Au(III) in the bath is found to be ∼10 −6 cm 2 /s and the energy of activation (43 kJ/mol) is deduced from the cyclic voltammograms at different temperatures. The nucleation and growth of gold on gold working electrode is investigated by chronoamperometry. The progressive nucleation mechanism is found for gold deposition using Scharifker–Hills’ model with three-dimensional (3D) diffusion-controlled growth nucleation. The introduction of the additive A does not influence this mechanism. The gold electrodeposits are characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and cathodic polarization measurements. Experimental results indicate that additive A increases the cathodic polarization of bath, refines the grains of electrodeposit and changes the preferred orientation of electrodeposit from [1 1 1] direction to [2 0 0] direction.

  14. Electrochemical behavior of ruthenium (III), rhodium (III) and palladium (II) in 1-butyl-3-methylimidazolium chloride ionic liquid

    Energy Technology Data Exchange (ETDEWEB)

    Jayakumar, M.; Venkatesan, K.A. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Srinivasan, T.G. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)], E-mail: tgs@igcar.gov.in; Vasudeva Rao, P.R. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)

    2009-11-01

    Electrochemical behavior of ruthenium (III), rhodium (III) and palladium (II) in 1-butyl-3-methylimidazolium chloride (bmimCl) and their ternary and binary solutions in bmimCl was studied at various working electrodes at 373 K by cyclic voltammetry and chronoamperometry. Ruthenium (III) chloride forms a stable solution with bmimCl and the cyclic voltammogram of ruthenium (III) in bmimCl recorded at glassy carbon electrode consisted of several redox waves due to the complex nature of ruthenium to exist in several oxidation states. Electrolysis of ruthenium (III) chloride in bmimCl at the cathodic limit of bmimCl (-1.8 V (vs. Pd)) did not result in ruthenium metal deposition. However, it was deposited from bmimPF{sub 6} and bmimNTf{sub 2} room temperature ionic liquids at -0.8 V (vs. Pd). The electrochemical behavior of ruthenium (III) in bmimCl in the presence of palladium (II) and rhodium (III) was studied by cyclic voltammetry. The presence of palladium (II) in bmimCl favors underpotential deposition of ruthenium metal. The nuclear loop at -0.5 V (vs. Pd) was observed in all solutions when palladium (II) co-existed with other two metal ions. Nucleation and growth of the metal on glassy carbon working electrode was investigated by chronoamperometry. The growth and decay of chronocurrents has been found to follow the instantaneous nucleation model with three-dimensional growth of nuclei.

  15. Influence of Oxidation Treatments and Surface Finishing on the Electrochemical Behavior of Ni-20Cr HVOF Coatings

    Science.gov (United States)

    Ruiz-Luna, H.; Porcayo-Calderon, J.; Alvarado-Orozco, J. M.; Mora-García, A. G.; Martinez-Gomez, L.; Trápaga-Martínez, L. G.; Muñoz-Saldaña, J.

    2017-12-01

    The low-temperature electrochemical behavior of HVOF Ni-20Cr coatings was assessed. The coatings were evaluated in different conditions including as-sprayed, as-ground, and heat-treated in air and argon atmospheres. A detailed analysis of the coatings was carried out by means of XRD, SEM, and EPMA, prior and after the corrosion test. The corrosion rate was analyzed in a NaCl solution saturated with CO2. Results demonstrate that the use of a low-oxygen partial pressure favors the formation of a Cr2O3 layer on the surface of the coatings. According to the electrochemical results, the lower corrosion rates were obtained for the heat-treated coatings irrespective of the surface finishing, being the ground and argon heat-treated condition that shows the best corrosion performance. This behavior is due to the synergistic effect of the low-pressure heat treatment and the grinding processes. The grinding promotes a more homogeneous reaction area without surface heterogeneities such as voids, and the pre-oxidation treatment decreases the porosity content of the coating and also allows the growing of a Cr-rich oxide scale which acts as a barrier against the ions of the aqueous solution.

  16. ELECTROCHEMICAL BEHAVIOR OF POLYCRYSTALLINE COPPER DURING THE ADSORPTION OF CO ABSTRACT

    Directory of Open Access Journals (Sweden)

    J. Salimon

    2017-12-01

    Full Text Available The electrochemical properties of electrode copper in carbon monoxide-saturated phosphate buffered solution were investigated. The electrochemistry of copper surface was sufficiently changed after the supporting electrolyte solution was saturated with CO. The hydrogen evolution region was depressed and shifted cathodically due to the adsorption process of CO on the copper surface in a linear or terminally bonded manner, Cu-CO . The oxidation and the reduction peaks of copper were significantly changed with two couple of redox peaks. This is due to the subsequent formation and the corresponding reduction of copper(I and the copper carbon monoxides species. Further changed in electrochemical properties occurred when the electrode surface was polarized at high cathodic potential (-1.4 V for a period of time (15 min. The hydrogen evolution region was further depressed due to the adsorption of CO process in multiple bonding sites as adsorbed bridge bonded CO, Cu-CO B L that occurred predominantly.

  17. Evaluation of Electrochemical Behavior of Nopal Extract (Opuntia Ficus- Indica as Possible Corrosion Inhibitor

    Directory of Open Access Journals (Sweden)

    Araceli Mandujano-Ruíz

    2017-11-01

    Full Text Available Corrosion is one of the main problems of degradation in components, tooling, equipment and even in structural applications, examples of this are the carbon steels. In the present work, the capacity of corrosion inhibition of a biodegradable organic extract from the Nopal plant (Opuntia ficus-indica, for the protection of carbon steel type AISI 1018 was studied adding 50% v/v of the Nopal extract (EN in a solution of H2SO4 (0.6 mol.l-1. Polarization Resistance (LPR and Electrochemical Impedance Spectroscopy (EIS techniques were used for the electrochemical evaluation at room temperature for 24 h in order to obtain corrosion rates (Vcorr and inhibition efficiency (IE. Metallographic examination was also carried out to register the surface damage by corrosion. The results showed a reduction of the Vcorr with a maximum IE value of about 84% by adding the organic- liquid extracted from Nopal.

  18. Synthesis and electrochemical behavior of nanostructured cauliflower-shape Co-Ni/Co-Ni oxides composites

    International Nuclear Information System (INIS)

    Gupta, Vinay; Kawaguchi, Toshikazu; Miura, Norio

    2009-01-01

    Nanostructured Co-Ni/Co-Ni oxides were electrochemically deposited onto stainless steel electrode by electrochemical method and characterized for their structural and supercapacitive properties. The SEM images indicated that the obtained Co-Ni/Co-Ni oxides had cauliflower-type nanostructure. The X-ray diffraction pattern showed the formation of Co 3 O 4 , NiO, Co and Ni. The EDX elemental mapping images indicated that Ni, Co and O are distributed uniformly. The deposited Co-Ni/Co-Ni oxides showed good supercapacitive characteristics with a specific capacitance of 331 F/g at 1 mA/cm 2 current density in 1 M KOH electrolyte. A mechanism of the formation of cauliflower-shape Co-Ni/Co-Ni oxides was proposed. A variety of promising applications in the fields such as energy storage devices and sensors can be envisioned from Co-Ni/Co-Ni oxides

  19. Synthesis of Some Novel Pyrimidine Derivatives and Investigation of their Electrochemical Behavior

    International Nuclear Information System (INIS)

    Akbas, Esvet; Gumus, Selcuk; Sumer, Mehmet Rauf; Akyaz, Inci; Levent, Abdulkadir

    2010-01-01

    2-Iminopyrimidines (1a-e) and 2-thioxopyrimidine (2) were synthesized using the Biginelli three component cyclocondensation reaction of an appropriate β-diketone, arylaldehyde, and guanidine (for 1a-e) or thiourea (for 2). The electrochemical properties of the novel systems were investigated by CV and DPV. Moreover, B3LYP/6-31G(d,p) method was applied to the present structures in order to gather some structural and physicochemical data

  20. Corrosion-electrochemical behavior of zirconium in molten alkali metal carbonates

    Science.gov (United States)

    Nikitina, E. V.

    2016-08-01

    The corrosion and electrochemical characteristics of zirconium during its interaction with molten lithium, sodium, and potassium carbonates containing from 1 to 5 wt % additives to the salt phase are studied in a temperature range of 500-800°C using gravimetry, corrosion potential measurement, and anodic polarization. The substances decreasing the corrosion losses due to the strengthening and thickening of an oxide film (lithium, sodium, potassium hydroxides) are used as passivators. Sodium chloride, fluoride, and sulfate serve as corrosion stimulators (activators).

  1. Electrochemical impedance spectroscopy of oxidized porous silicon

    Energy Technology Data Exchange (ETDEWEB)

    Mula, Guido, E-mail: guido.mula@unica.it [Dipartimento di Fisica, Università degli Studi di Cagliari, Cittadella Universitaria di Monserrato, S.P. 8 km 0.700, 09042 Cagliari (Italy); Tiddia, Maria V. [Dipartimento di Fisica, Università degli Studi di Cagliari, Cittadella Universitaria di Monserrato, S.P. 8 km 0.700, 09042 Cagliari (Italy); Ruffilli, Roberta [Nanochemistry, Istituto Italiano di Tecnologia, Via Morego 30, 16163 Genova (Italy); Falqui, Andrea [Nanochemistry, Istituto Italiano di Tecnologia, Via Morego 30, 16163 Genova (Italy); Dipartimento di Scienze Chimiche e Geologiche, Università degli Studi di Cagliari, Cittadella Universitaria di Monserrato, S.P. 8 km 0.700, 09042 Cagliari (Italy); Palmas, Simonetta; Mascia, Michele [Dipartimento di Ingegneria Meccanica Chimica e dei Materiali, Università degli Studi di Cagliari, Piazza d' Armi, 09126 Cagliari (Italy)

    2014-04-01

    We present a study of the electrochemical oxidation process of porous silicon. We analyze the effect of the layer thickness (1.25–22 μm) and of the applied current density (1.1–11.1 mA/cm{sup 2}, values calculated with reference to the external samples surface) on the oxidation process by comparing the galvanostatic electrochemical impedance spectroscopy (EIS) measurements and the optical specular reflectivity of the samples. The results of EIS were interpreted using an equivalent circuit to separate the contribution of different sample parts. A different behavior of the electrochemical oxidation process has been found for thin and thick samples: whereas for thin samples the oxidation process is univocally related to current density and thickness, for thicker samples this is no more true. Measurements by Energy Dispersive Spectroscopy using a Scanning Electron Microscopy confirmed that the inhomogeneity of the electrochemical oxidation process is increased by higher thicknesses and higher currents. A possible explanation is proposed to justify the different behavior of thin and thick samples during the electrochemical process. - Highlights: • A multidisciplinary approach on porous Si electrochemical oxidation is proposed. • Electrochemical, optical, and structural characterizations are used. • Layer thickness and oxidation current effects are shown. • An explanation of the observed behavior is proposed.

  2. The self-assembly of redox active peptides: Synthesis and electrochemical capacitive behavior.

    Science.gov (United States)

    Piccoli, Julia P; Santos, Adriano; Santos-Filho, Norival A; Lorenzón, Esteban N; Cilli, Eduardo M; Bueno, Paulo R

    2016-05-01

    The present work reports on the synthesis of a redox-tagged peptide with self-assembling capability aiming applications in electrochemically active capacitive surfaces (associated with the presence of the redox centers) generally useful in electroanalytical applications. Peptide containing ferrocene (fc) molecular (redox) group (Ac-Cys-Ile-Ile-Lys(fc)-Ile-Ile-COOH) was thus synthesized by solid phase peptide synthesis (SPPS). To obtain the electrochemically active capacitive interface, the side chain of the cysteine was covalently bound to the gold electrode (sulfur group) and the side chain of Lys was used to attach the ferrocene in the peptide chain. After obtaining the purified redox-tagged peptide, the self-assembly and redox capability was characterized by cyclic voltammetry (CV) and electrochemical impedance-based capacitance spectroscopy techniques. The obtained results confirmed that the redox-tagged peptide was successfully attached by forming an electroactive self-assembled monolayer onto gold electrode. The design of redox active self-assembly ferrocene-tagged peptide is predictably useful in the development of biosensor devices precisely to detect, in a label-free platform, those biomarkers of clinical relevance. © 2016 Wiley Periodicals, Inc. Biopolymers (Pept Sci) 106: 357-367, 2016. © 2016 Wiley Periodicals, Inc.

  3. Behavioral symptoms related to cognitive impairment.

    Science.gov (United States)

    Dillon, Carol; Serrano, Cecilia M; Castro, Diego; Leguizamón, Patricio Perez; Heisecke, Silvina L; Taragano, Fernando E

    2013-01-01

    Neuropsychiatric symptoms (NPS) are core features of Alzheimer's disease and related dementias. On one hand, behavioral symptoms in patients with mild cognitive impairment (MCI) can indicate an increased risk of progressing to dementia. On the other hand, mild behavioral impairment (MBI) in patients who usually have normal cognition indicates an increased risk of developing dementia. Whatever the cause, all dementias carry a high rate of NPI. These symptoms can be observed at any stage of the disease, may fluctuate over its course, are a leading cause of stress and overload for caregivers, and increase rates of hospitalization and early institutionalization for patients with dementia. The clinician should be able to promptly recognize NPI through the use of instruments capable of measuring their frequency and severity to support diagnosis, and to help monitor the treatment of behavioral symptoms. The aims of this review are to describe and update the construct 'MBI' and to revise the reported NPS related to prodromal stages of dementia (MCI and MBI) and dementia stages of Alzheimer's disease and frontotemporal lobar degeneration.

  4. Kinetic study on electrochemical oxidation of catechols in the ...

    Indian Academy of Sciences (India)

    glassy carbon electrode in different experimental conditions. The electrogenerated ... cancer activities.5 Catechols can be easily oxidized electrochemically to ... from unity and approaches to zero in basic solution. This behavior is related to the ...

  5. Microstructure and electrochemical corrosion behavior of a Pb-1 wt%Sn alloy for lead-acid battery components

    Energy Technology Data Exchange (ETDEWEB)

    Peixoto, Leandro C.; Osorio, Wislei R.; Garcia, Amauri [Department of Materials Engineering, University of Campinas - UNICAMP, PO Box 612, 13083-970, Campinas - SP (Brazil)

    2009-07-15

    The aim of this study was to evaluate the effect of solidification cooling rates on the as-cast microstructural morphologies of a Pb-1 wt%Sn alloy, and to correlate the resulting microstructure with the corresponding electrochemical corrosion resistance in a 0.5 M H{sub 2}SO{sub 4} solution at 25 C. Cylindrical low-carbon steel and insulating molds were employed permitting the two extremes of a significant range of solidification cooling rates to be experimentally examined. Electrochemical impedance spectroscopy (EIS) diagrams, potentiodynamic polarization curves and an equivalent circuit analysis were used to evaluate the electrochemical corrosion response of Pb-1 wt%Sn alloy samples. It was found that lower cooling rates are associated with coarse cellular arrays which result in better corrosion resistance than fine cells which are related to high cooling rates. The experimental results have shown that that the pre-programming of microstructure cell size of Pb-Sn alloys can be used as an alternative way to produce as-cast components of lead-acid batteries with higher corrosion resistance. (author)

  6. An integrated electrochemical device based on immunochromatographic test strip and enzyme labels for sensitive detection of disease-related biomarkers

    Energy Technology Data Exchange (ETDEWEB)

    Zou, Zhexiang; Wang, Jun; Wang, Hua; Li, Yao Q.; Lin, Yuehe

    2012-05-30

    A novel electrochemical biosensing device that integrates an immunochromatographic test strip and a screen-printed electrode (SPE) connected to a portable electrochemical analyzer was presented for rapid, sensitive, and quantitative detection of disease-related biomarker in human blood samples. The principle of the sensor is based on sandwich immunoreactions between a biomarker and a pair of its antibodies on the test strip, followed by highly sensitive square-wave voltammetry (SWV) detection. Horseradish peroxidase (HRP) was used as a signal reporter for electrochemical readout. Hepatitis B surface antigen (HBsAg) was employed as a model protein biomarker to demonstrate the analytical performance of the sensor in this study. Some critical parameters governing the performance of the sensor were investigated in detail. The sensor was further utilized to detect HBsAg in human plasma with an average recovery of 91.3%. In comparison, a colorimetric immunochromatographic test strip assay (ITSA) was also conducted. The result shows that the SWV detection in the electrochemical sensor is much more sensitive for the quantitative determination of HBsAg than the colorimetric detection, indicating that such a sensor is a promising platform for rapid and sensitive point-of-care testing/screening of disease-related biomarkers in a large population

  7. Room-temperature Electrochemical Synthesis of Carbide-derived Carbons and Related Materials

    Energy Technology Data Exchange (ETDEWEB)

    Gogotsi, Yury [Drexel Univ., Philadelphia, PA (United States). Nanomaterials Group. Materials Science and Engineering Dept.

    2015-02-28

    This project addresses room-temperature electrochemical etching as an energy-efficient route to synthesis of 3D nanoporous carbon networks and layered 2D carbons and related structures, as well as provides fundamental understanding of structure and properties of materials produced by this method. Carbide-derived-carbons (CDCs) are a growing class of nanostructured carbon materials with properties that are desirable for many applications, such as electrical energy and gas storage. The structure of these functional materials is tunable by the choice of the starting carbide precursor, synthesis method, and process parameters. Moving from high-temperature synthesis of CDCs through vacuum decomposition above 1400°C and chlorination above 400°C, our studies under the previous DOE BES support led to identification of precursor materials and processing conditions for CDC synthesis at temperatures as low as 200°C, resulting in amorphous and highly reactive porous carbons. We also investigated synthesis of monolithic CDC films from carbide films at 250-1200°C. The results of our early studies provided new insights into CDC formation, led to development of materials for capacitive energy storage, and enabled fundamental understanding of the electrolyte ions confinement in nanoporous carbons.

  8. Carbonate anion controlled growth of LiCoPO4/C nanorods and its improved electrochemical behavior

    International Nuclear Information System (INIS)

    Gangulibabu; Nallathamby, Kalaiselvi; Meyrick, Danielle; Minakshi, Manickam

    2013-01-01

    Highlights: ► Carbonate anion controlled growth of LiCoPO 4 nanorods has been prepared. ► Mixture of H 2 CO 3 + (NH 4 ) 2 CO 3 increases the CO 3 2− concentration and acts as an effective growth inhibitor. ► Heating the carbonate rich precursor in an inert atmosphere produces a Co 2 P phase that is conductive. ► Addition of super P carbon resulted in an amorphous carbon coating on LiCoPO 4 particles. ► LiCoPO 4 /C nanorods with a co-existence of Co 2 P exhibit excellent discharge capacity with retention on multiple cycling. -- Abstract: LiCoPO 4 /C nanocomposite with growth controlled by carbonate anions was synthesized via a unique solid-state fusion method. Carbonate anions in the form of H 2 CO 3 or a mixture of H 2 CO 3 + (NH 4 ) 2 CO 3 have been used as a growth inhibiting modifier to produce morphology controlled lithium cobalt phosphate. The presence of cobalt phosphide (Co 2 P) as a second phase improved the conductivity and electrochemical properties of the parent LiCoPO 4. The formation of Co 2 P is found to be achievable only in an inert atmosphere. Super P ® carbon (10 wt.%) provided an adherent carbon coating on pristine LiCoPO 4 resulting in the LiCoPO 4 /C composite cathode. This electrode exhibited enhanced electrochemical properties: capacity of 123 mAh g −1 with excellent capacity retention of 89% after 30 cycles, and reasonable rate capability of up to 5 C rate. The synergistic effect of carbonate anions and formation of Co 2 P under inert atmosphere has influenced the electrochemical behavior of LiCoPO 4 /C cathode through controlling the morphology and increasing the conductivity

  9. The electrochemical polishing behavior of the Inconel 718 alloy in perchloric-acetic mixed acids

    International Nuclear Information System (INIS)

    Huang, C.A.; Chen, Y.C.; Chang, J.H.

    2008-01-01

    The electropolishing behavior of the Inconel 718 alloy was studied by using rotating disc electrode (RDE) in the HClO 4 -CH 3 COOH mixed acids with different HClO 4 -concentrations. After electropolishing, surface morphologies of RDE specimens were examined with surface profiler, atomic force microscope and scanning electron microscope. According to the surface morphologies observed, three types of anodic dissolution behavior can be characterized in relation to the HClO 4 -content in mixed acids; namely, leveling without brightening of the surface in the mixed acids with 10 and 20 vol% HClO 4 , leveling and brightening of the surface in the mixed acids with 30 and 40 vol% HClO 4 , and a matt and gray surface in the mixed acids with 50 vol% or more HClO 4 . Anodic dissolution in the first and second dissolution types follows a mass-transfer controlled mechanism, in which a linear relationship between the reciprocal of limiting-current density and the reciprocal of square root of rotating speed of RDE specimen can be detected. Owing to precipitation of salt film on the polished surface of the Inconel 718 material, saturated dissolved metallic ions could be the chemical species for the mass-controlled mechanism. The salt film, in addition, could enhance the corrosion resistance of the Inconel 718 alloy

  10. Electrochemical behavior of zirconium in the LiCl-KCl molten salt at Mo electrode

    Energy Technology Data Exchange (ETDEWEB)

    Chen Zeng; Li Yongjun [Key Laboratory of Photovoltaic Materials of Henan Province and School of Physics and Electronics, Henan, University, Kaifeng 475001 (China); Li Shengjun, E-mail: lishengjun@hrbeu.edu.cn [Key Laboratory of Photovoltaic Materials of Henan Province and School of Physics and Electronics, Henan, University, Kaifeng 475001 (China)

    2011-05-19

    Highlights: > The electrochemical reduction of Zr(II)/Zr and Zr(IV)/Zr(II) were both proved to be diffusion-controlled process. > In the 773 K-973 K range, the diffusion coefficients of Zr(II) and Zr(IV) were determined: D{sub Zr(II)} = 0.15567exp{l_brace}-69.65 x 10{sup 3}RT(K){r_brace} cm{sup 2}/s, D{sub Zr(IV)} = 1.09 x 10{sup -4}exp{l_brace}-44.39 x 10{sup 3}RT(K){r_brace} cm{sup 2}/s. > The activation energy values for the diffusion process were 69.65 kJ/mol and 44.39 kJ/mol, respectively. > This investigation will be useful for the further cognition of the molten salt electrolysis of zirconium. - Abstract: The electroreduction process of Zr(IV) was studied at molybdenum electrode in LiCl-KCl-K{sub 2}ZrF{sub 6} molten salt. The transient electrochemical techniques, such as cyclic voltammetry and chronopotenimetry were used. The experimental results showed that the electrochemical reduction of Zr(II)/Zr and Zr(IV)/Zr(II) were both diffusion-controlled process. In the 773-973 K range, the diffusion coefficients of Zr(ii) and Zr(IV) were determined: D{sub Zr(II)} = 0.15567exp{l_brace}-69.65 x 10{sup 3}RT(K){r_brace} cm{sup 2}/s, D{sub Zr(IV)} = 1.09 x 10{sup -4} exp{l_brace}-44.39 x 10{sup 3}RT(K){r_brace} cm{sup 2}/s. The activation energy values for the diffusion process were 69.65 kJ/mol and 44.39 kJ/mol, respectively.

  11. Effect of passivation with CO on the electrochemical corrosion behavior of uranium-niobium alloy

    International Nuclear Information System (INIS)

    Fu Xiaoguo; Dai Lianxin; Zou Juesheng; Bai Chaomao; Wang Xiaolin

    2000-01-01

    Electrochemical studies are performed to investigate the corrosion resistance of uranium-niobium alloy before and after passivated with carbon monoxide. Using X-ray photoelectron spectroscopy (XPS), the surface composition of specimen passivated with carbon monoxide is determined. The corrosion resistance of uranium-niobium alloy is well improved because the passive layer (UC/UC x O y + Nb 2 O 5 + UO 2 ) on surface serves as passive film and increases the anodic impedance after the specimen is passivated with carbon monoxide

  12. Electrochemical Cell

    DEFF Research Database (Denmark)

    1999-01-01

    The invention relates to a rechargeable electrochemical cell comprising a negative electrode, an electrolyte and a positive electrode in which the positive electrode structure comprises a lithium cobalt manganese oxide of the composition Li¿2?Co¿y?Mn¿2-y?O¿4? where 0 ... for capacity losses in lithium ion cells and lithium-alloy cells....

  13. Corrosion electrochemical behaviors of silane coating coated magnesium alloy in NaCl solution containing cerium nitrate

    Energy Technology Data Exchange (ETDEWEB)

    Luo, F.; Li, Q.; Zhong, X.K.; Gao, H.; Dai, Y.; Chen, F.N. [School of Chemistry and Chemical Engineering, Southwest University Chongqing (China)

    2012-02-15

    Sol-gel coatings cannot provide adequate corrosion protection for metal/alloys in the corrosive environments due to their high crack-forming potential. This paper demonstrates the possibility to employ cerium nitrate as inhibitor to decrease the corrosion development of sol-gel-based silane coating on the magnesium alloy in NaCl solution. Cerium nitrate was added into the NaCl solution where the silane coating coated magnesium alloy was immersed. Scanning electron microscopy (SEM) was used to examine surface morphology of the silane coating coated magnesium alloy immersed in NaCl solutions doped and undoped with cerium nitrate. The corrosion electrochemical behaviors were investigated using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests. The results showed that the introduction of cerium nitrate into NaCl solution could effectively inhibit the corrosion of the silane coating coated magnesium alloy. Moreover, the influence of concentration of cerium nitrate on the corrosion inhibition and the possible inhibiting mechanism were also discussed in detail. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  14. Physiological Fluctuations in Brain Temperature as a Factor Affecting Electrochemical Evaluations of Extracellular Glutamate and Glucose in Behavioral Experiments

    Science.gov (United States)

    2013-01-01

    The rate of any chemical reaction or process occurring in the brain depends on temperature. While it is commonly believed that brain temperature is a stable, tightly regulated homeostatic parameter, it fluctuates within 1–4 °C following exposure to salient arousing stimuli and neuroactive drugs, and during different behaviors. These temperature fluctuations should affect neural activity and neural functions, but the extent of this influence on neurochemical measurements in brain tissue of freely moving animals remains unclear. In this Review, we present the results of amperometric evaluations of extracellular glutamate and glucose in awake, behaving rats and discuss how naturally occurring fluctuations in brain temperature affect these measurements. While this temperature contribution appears to be insignificant for glucose because its extracellular concentrations are large, it is a serious factor for electrochemical evaluations of glutamate, which is present in brain tissue at much lower levels, showing smaller phasic fluctuations. We further discuss experimental strategies for controlling the nonspecific chemical and physical contributions to electrochemical currents detected by enzyme-based biosensors to provide greater selectivity and reliability of neurochemical measurements in behaving animals. PMID:23448428

  15. Role of polymeric binders on mechanical behavior and cracking resistance of silicon composite electrodes during electrochemical cycling

    Science.gov (United States)

    Li, Dawei; Wang, Yikai; Hu, Jiazhi; Lu, Bo; Dang, Dingying; Zhang, Junqian; Cheng, Yang-Tse

    2018-05-01

    This work focuses on understanding the role of various binders, including sodium alginate (SA), Nafion, and polyvinylidene fluoride (PVDF), on the mechanical behavior and cracking resistance of silicon composite electrodes during electrochemical cycling. In situ curvature measurement of bilayer electrodes, consisting of a silicon-binder-carbon black composite layer on a copper foil, is used to determine the effects of binders on bending deformation, elastic modulus, and stress on the composite electrodes. It is found that the lithiation induced curvature and the modulus of the silicon/SA electrodes are larger than those of electrodes with Nafion and PVDF as binders. Although the modulus of Nafion is smaller than that of PVDF, the curvature and the modulus of silicon/Nafion composite are larger than those of silicon/PVDF electrodes. The moduli of all three composites decrease not only during lithiation but also during delithiation. Based on the measured stress and scanning electron microscopy observations of cracking in the composite electrodes, we conclude that the stress required to crack the composite electrodes with SA and Nafion binders is considerably higher than that of the silicon/PVDF electrode during electrochemical cycling. Thus, the cracking resistance of silicon/SA and silicon/Nafion composite electrodes is higher than that of silicon/PVDF electrodes.

  16. Electrochemical behavior of sebaconitrile as a cosolvent in the formulation of electrolytes at high potentials for lithium-ion batteries

    International Nuclear Information System (INIS)

    Nanini-Maury, Elise; Światowska, Jolanta; Chagnes, Alexandre; Zanna, Sandrine; Tran-Van, Pierre; Marcus, Philippe; Cassir, Michel

    2014-01-01

    The electrochemical behavior of new high potential electrolyte containing sebaconitrile in LiPF 6 /EC:DMC or LiBF 4 was studied on glassy carbon and LiCoO 2 , LiCoPO 4 as positive electrode materials. The increase of sebaconitrile concentration in EC:DMC electrolyte provides better electrolyte stability at higher potentials on glassy carbon as observed by cyclic voltammetry. Promising electrochemical results showing good reversibility and insertion/deinsertion efficiency have been also obtained on LiCoPO 4 electrode cycled up to 5.3 V vs Li + /Li as upper potential limit. However, the cycling of LiCoPO 4 at higher potential (6 V vs Li + /Li) shows lower reversibility and efficiency of insertion/deinsertion process due to the oxidative decomposition of the electrolyte at high potentials. The surface analysis performed by X-ray photoelectron spectroscopy confirms the formation of a surface layer induced by electrolyte degradation on both types of positive electrodes, which hinder the Li diffusion. The layer composition and morphology vary as a function of electrolyte composition and type of electrode

  17. Electrochemical behavior and biological response of Mesenchymal Stem Cells on cp-Ti after N-ions implantation

    Science.gov (United States)

    Rizwan, M.; Ahmad, A.; Deen, K. M.; Haider, W.

    2014-11-01

    Titanium and its alloys are most widely used as implant materials due to their excellent biocompatibility, mechanical properties and chemical stability. In this study Nitrogen ions of known dosage were implanted over cp-Ti by Pelletron accelerator with beam energy of 0.25 MeV.The atomic force microscopy of bare and nitrogen implanted specimens confirmed increase in surface roughness with increase in nitrogen ions concentration. X-ray diffraction patterns of ions implanted surfaces validated the formation of TiN0.3 and Ti3N2-xnitride phases. The tendency to form passive film and electrochemical behavior of these surfaces in ringer lactate (RL) solution was evaluated by Potentiodynamic polarization and electrochemical impedance spectroscopy respectively. It is proved that nitrogen ions implantation was beneficial to reduce corrosion rate and stabilizing passive film by increasing charge transfer resistance in RL. It was concluded that morphology and proliferation of Mesenchymal Stem Cells on nitrogen ions implanted surfaces strongly depends on surface roughness and nitride phases.

  18. Corrosion Behavior of Surface-Treated Implant Ti-6Al-4V by Electrochemical Polarization and Impedance Studies

    Science.gov (United States)

    Paul, Subir; Yadav, Kasturi

    2011-04-01

    Implant materials for orthopedic and heart surgical services demand a better corrosion resistance material than the presently used titanium alloys, where protective oxide layer breaks down on a prolonged stay in aqueous physiological human body, giving rise to localized corrosion of pitting, crevice, and fretting corrosion. A few surface treatments on Ti alloy, in the form of anodization, passivation, and thermal oxidation, followed by soaking in Hank solution have been found to be very effective in bringing down the corrosion rate as well as producing high corrosion resistance surface film as reflected from electrochemical polarization, cyclic polarization, and Electrochemical Impedance Spectroscopy (EIS) studies. The XRD study revealed the presence of various types of oxides along with anatase and rutile on the surface, giving rise to high corrosion resistance film. While surface treatment of passivation and thermal oxidation could reduce the corrosion rate by 1/5th, anodization in 0.3 M phosphoric acid at 16 V versus stainless steel cathode drastically brought down the corrosion rate by less than ten times. The mechanism of corrosion behavior and formation of different surface films is better understood from the determination of EIS parameters derived from the best-fit equivalent circuit.

  19. Studies on the electrochemical behavior of heavy lanthanide ions and the synthesis, characterization of heavy metal chelate complexes

    International Nuclear Information System (INIS)

    Kang, Sam Woo; Chang, Choo Hwan; Son, Byung Chan; Suh, Moo Yul; Kim, Chae Kyun

    1991-01-01

    Electrochemical behavior of some heavy lanthanide ions(Gd 3+ , Tb 3+ , Dy 3+ , Ho 3+ , Er 3+ , Tm 3+ , Yb 3+ and Lu 3+ ) in various supporting electrolytes has been investigated by dc polarography, differential pulse polarography and cyclic voltammetry. The peak potentials and the peak currents, their dependency on the concentration and pH effects, the reversibility of the electrode reactions are described. The reduction of Gd 3+ , Tb 3+ , Dy 3+ , Ho 3+ , Er 3+ , Tm 3+ and Lu 3+ ions in 0.1M lithium chloride solution proceeds by a three-electron change directly to the metallic state, whereas the reduction of Yb 3+ proceeds by a one-electron change followed by a two-electron change. It was found that, in differential pulse polarography and cyclic voltammetry, the peak potential, peak current and current function showed constant value in the pH range of 4.0-6.0 by varying pH and scan rates. And also the current function is found to decrease as the sweep rate is increased when the pH reaches 4.0. This fact may indicate a chemical reaction coupled with the electrochemical reaction at lower pH values(pH 3+ ion is possible to determine voltammetrically within the error of ±3.5% in the presence of other competitive lanthanide ions. (Author)

  20. Electrochemical studies on the redox behavior of zirconium in the LiF-NaF eutectic melt

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Liang [School of Metallurgy, Northeastern University, Shenyang 110004 (China); Xiao, Yanping [School of Metallurgical Engineering, Anhui University of Technology, Ma' anshan 243002 (China); Zr-Hf-Ti Metallurgie B.V., Den Haag 2582 SB (Netherlands); Xu, Qian, E-mail: qianxu@shu.edu.cn [State Key Laboratory of Advanced Special Steel, Shanghai University, Shanghai 200072 (China); Sandwijk, Anthonie van [Zr-Hf-Ti Metallurgie B.V., Den Haag 2582 SB (Netherlands); Zhao, Zhuo [School of Metallurgical Engineering, Anhui University of Technology, Ma' anshan 243002 (China); Song, Qiushi; Cai, Yanqing [School of Metallurgy, Northeastern University, Shenyang 110004 (China); Yang, Yongxiang [School of Metallurgical Engineering, Anhui University of Technology, Ma' anshan 243002 (China); Department of Materials Science and Engineering, Delft University of Technology, 2628 CD Delft (Netherlands)

    2017-05-15

    In the present paper, a detailed study of the redox behavior of zirconium in the eutectic LiF-NaF system was carried out on an inert molybdenum electrode at 750 °C. Several transient electrochemical methods were used such as cyclic voltammetry, square wave voltammetry, chronopotentiometry, and open circuit voltammetry. The reduction of Zr (IV) was found to follow a two-step mechanism of Zr (IV)/Zr (II) and Zr (II)/Zr at the potentials of about −1.10 and −1.50 V versus Pt, respectively. The theoretical evaluations of the number of transferred electrons according to both cyclic voltammetry and square wave voltammetry further confirmed the Zr reduction mechanism. The estimations of Zr (IV) diffusion coefficient in the LiF-NaF eutectic melt at 750 °C through cyclic voltammetry and chronopotentiometry are in fair agreement, as to be approximately 1.13E-5 and 2.42E-5 cm{sup 2}/s, respectively. - Highlights: •The redox mechanism of zirconium in a fluoride salt system was investigated. •A multi-step redox process of Zr was found with various electrochemical methods. •Perspectives on zirconium electro-refining process were proposed.

  1. Electrochemical and corrosion behavior of a 304 stainless-steel-based metal alloy wasteform in dilute aqueous environments

    International Nuclear Information System (INIS)

    Chen, Jian; Asmussen, R. Matthew; Zagidulin, Dmitrij; Noël, James J.; Shoesmith, David W.

    2013-01-01

    Highlights: ► We investigated the corrosion behavior of a metal alloy in six reference solutions. ► Majority of rhenium used as a technetium surrogate contained within a Fe 2 Mo phase. ► This prototype alloy exhibited generally passive behavior in all environments. ► Passivity breakdown events can occur and lead to localized corrosion. - Abstract: The electrochemical and corrosion behavior of a stainless-steel-based alloy made as a prototype metallic nuclear wasteform to immobilize 99 Tc, has been studied in a number of reference solutions ranging in pH from 4 to 10. The results showed the 47SS(304)-9Zr–23Mo prototype alloy contained at least five distinct phases with the majority of the Re, used as a Tc surrogate, contained within a Fe 2 Mo intermetallic phase. Polarization studies showed this alloy exhibited generally passive behavior in a range of dilute aqueous environments. Impedance measurements indicated passivity breakdown events can occur and lead to localized corrosion, especially in slightly alkaline conditions.

  2. Effect of the carbon dioxide pressure on the electrochemical behavior of 3Cr low alloyed steel at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Zhijun, E-mail: jiazhijunwin@163.com [Department of Chemical Engineering, University of Tsinghua, Beijing 100084 (China); Key Laboratory of Corrosion and Protection of Chinese Ministry of Education, University of Science and Technology Beijing, Beijing 100083 (China); Li, Xiaogang; Du, Cuiwei; Liu, Zhiyong; Gao, Jin [Key Laboratory of Corrosion and Protection of Chinese Ministry of Education, University of Science and Technology Beijing, Beijing 100083 (China)

    2012-10-15

    Electrochemical corrosion behavior of 3Cr steel in CO{sub 2}-containing solution at a high temperature was investigated by various electrochemical measurements and analysis as well as thermodynamic calculations of ionic concentrations and equilibrium electrode potentials. A conceptual model was developed to illustrate the electrochemical corrosion mechanism of 3Cr steel in the CO{sub 2}-containing sodium chloride solution. Comparing the corrosion potentials of 3Cr steel in the test solution under different CO{sub 2} pressures with the conceptual model, it is found that anodic reactions of the 3Cr steel contain a direct dissolution of Fe, and the formation of corrosion scales, FeCO{sub 3} and Cr(OH){sub 3}, by Fe+HCO{sub 3}{sup -}=FeCO{sub 3}+H{sup +}+2e and Cr + 3OH{sup -} = Cr(OH){sub 3}. With the CO{sub 2} pressure increasing, the corrosion potential has a positive shift. It indicates that the CO{sub 2} pressure has a greater effect on the cathodic reaction than that of anodic reaction. And the corrosion current has positive linear relationship with the increase of CO{sub 2} pressure. It is attributed to the concentration increasing of the reactants of the cathodic reaction. According to analysis of the electrochemical impedance spectroscopy, the scale forming reactions dominate the corrosion process when the CO{sub 2} pressure is lower than 0.6 MPa and the dissolution of Fe, followed by the consecutive mechanism with adsorbed intermediate products, takes up the dominant part in the anodic process when the CO{sub 2} pressure exceeds 0.6 MPa. -- Highlights: Black-Right-Pointing-Pointer A conceptual model is developed to illustrate the corrosion mechanism. Black-Right-Pointing-Pointer A good reference electrode which is used at high temperature is made. Black-Right-Pointing-Pointer Corrosion current has positive linear relationship with the increase of CO{sub 2} pressure. Black-Right-Pointing-Pointer CO{sub 2} pressure has a greater effect on cathodic reaction than

  3. Relationship between the electrochemical behavior of multiwalled carbon nanotubes (MWNTs) loaded with CuO and the photocatalytic activity of Eosin Y-MWNTs-CuO system

    Science.gov (United States)

    Bui, Duc-Nguyen; Kang, Shi-Zhao; Qin, Lixia; Li, Xiang-Qing; Mu, Jin

    2013-02-01

    The photocatalytic system containing Eosin Y, multiwalled carbon nanotubes (MWNTs) and CuO (Eosin Y-MWNTs-CuO) was fabricated; meanwhile its photocatalytic activity for hydrogen evolution from triethanolamine (TEOA) aqueous solution was evaluated. Under visible light irradiation, the amount of hydrogen (H2) evolution increased greatly due to introduction of CuO in the photocatalytic system. Moreover, the electrochemical behavior of MWNTs loaded with CuO was explored using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The results clearly indicate that there is a strong relationship between the electrochemical behavior of MWNTs-CuO and the photocatalytic activity of Eosin Y-MWNTs-CuO, and the high photocatalytic activity of Eosin Y-MWNTs-CuO may mainly originate from the efficient electron-transfer in the system.

  4. Adherence and electrochemical behavior of calcium titanate coatings onto 304 stainless steel substrate

    Energy Technology Data Exchange (ETDEWEB)

    Esguerra A, J.; Aguilar, Y. [Universidad del Valle, Escuela de Ingenieria de Materiales, TPMR, Calle 13 No. 100-00, A. A. 25360 Cali (Colombia); Aperador, W. [Escuela Colombiana de Ingenieria Julio Garavito, Escuela de Ingenieria Mecanica, AK 45 No. 205-59 (Autopista Norte), A. A. 14520 Bogota (Colombia); Alba de Sanchez, N. [Universidad Autonoma de Occidente, Grupo de Investigacion en Ciencia e Ingenieria de Materiales, Calle 25 No. 115-85, A. A. 2790 Cali (Colombia); Bolanos P, G.; Rincon, C., E-mail: johanna.esguerra@univalle.edu.co [Universidad del Cauca, Departamento de Fisica, Laboratorio de Fisica de Bajas Temperaturas, Calle 5 No. 4-70, A. A. 996 Popayan (Colombia)

    2014-07-01

    Calcium titanate has been proposed as a coating for biomedical applications but it has not been reported characterization of adhesion failure mechanisms or electrochemical properties in time. In this work have been studied these properties of a calcium titanate coating growth onto AISI 304 steel deposited by r.f. magnetron sputtering. It was found that the coating has a critical adhesive load of 6.53 ± 0.14 N. With respect to its electrochemical properties potentiodynamic polarization curves show that the calcium titanate coating provides protection to AISI 304 steel. However. EIS indicates that even though metal dissolution occur through the pores in the coating, this leads to the precipitation of salts that block pores; this precipitates layer acts like and additional barrier to the metal dissolution in the system. The coatings deposition was carried out via magnetron sputtering during 4 hours at 500 grades C. The crystal structure of the films was determined by using glancing incident X-ray diffraction. The chemical composition of deposited films was performed by impedance dispersive X-ray spectroscopy (EDX) in the scanning electron microscopy (Jeol JSM-649 OLV Sem), and the grain size and the roughness was obtained using an atomic force microscopy from Asylum Research MFP-3D using a cantilever silicon tip in non-contact mode and calculated by scanning probe image processor. (Author)

  5. Adherence and electrochemical behavior of calcium titanate coatings onto 304 stainless steel substrate

    International Nuclear Information System (INIS)

    Esguerra A, J.; Aguilar, Y.; Aperador, W.; Alba de Sanchez, N.; Bolanos P, G.; Rincon, C.

    2014-01-01

    Calcium titanate has been proposed as a coating for biomedical applications but it has not been reported characterization of adhesion failure mechanisms or electrochemical properties in time. In this work have been studied these properties of a calcium titanate coating growth onto AISI 304 steel deposited by r.f. magnetron sputtering. It was found that the coating has a critical adhesive load of 6.53 ± 0.14 N. With respect to its electrochemical properties potentiodynamic polarization curves show that the calcium titanate coating provides protection to AISI 304 steel. However. EIS indicates that even though metal dissolution occur through the pores in the coating, this leads to the precipitation of salts that block pores; this precipitates layer acts like and additional barrier to the metal dissolution in the system. The coatings deposition was carried out via magnetron sputtering during 4 hours at 500 grades C. The crystal structure of the films was determined by using glancing incident X-ray diffraction. The chemical composition of deposited films was performed by impedance dispersive X-ray spectroscopy (EDX) in the scanning electron microscopy (Jeol JSM-649 OLV Sem), and the grain size and the roughness was obtained using an atomic force microscopy from Asylum Research MFP-3D using a cantilever silicon tip in non-contact mode and calculated by scanning probe image processor. (Author)

  6. Effect of incorporation of fly ash and granulated blast furnace in the electrochemical behavior of concretes of commercial cement

    International Nuclear Information System (INIS)

    Gutierrez-Junco, O. J.; Pineda-Triana, Y.; Vera-Lopez, E.

    2015-01-01

    This paper presents the findings of the research properties evaluation pastes of commercial cement (CPC), mixed with fly ash (FA) and granulated blast furnace slag (GBFS). Initially, the sample of 30 combinations were evaluated in terms of compressive strength to establish the optimal proportions from raw material. After that, four optimized blends were characterized during the setting and hardening process. Electrochemical tests were performed on concrete cylinders samples prepared with cementitious materials and a structural steel rod placed in the center of the specimen. With the objective to evaluate the performance before corrosion, thermodynamic and kinetic aspects were taken into consideration. The findings showed that commercial cements blended with fly ash and blast furnace slag as the ones used in this research presents a decreased behavior in mechanical and corrosion strength regarding to CPC. (Author)

  7. Electrochemical behavior of Th(IV) and its electrodeposition from ThF_4-LiCl-KCl melt

    International Nuclear Information System (INIS)

    Wang, Xianbin; Huang, Wei; Gong, Yu; Jiang, Feng; Zheng, Haiyang; Zhu, Tiejian; Long, Dewu; Li, Qingnuan

    2016-01-01

    The electrochemical behavior of Th(IV) ion on molybdenum (Mo) electrode was studied by cyclic voltammetry (CV) and square wave voltammetry (SWV) technologies at 773 K in ThF_4-LiCl-KCl melt. The reduction of Th(IV) to metal Th at −1.67 V (vs. Ag/AgCl) is a four-electron exchange process, which is quasi-reversible and diffusion-controlled. The diffusion coefficient (D) and activation energy of diffusion process for Th(IV) were determined to be 3.77 × 10"−"5 cm"2 s"−"1 and 59.2 kJ mol"−"1. The pulse potential electrolysis of ThF_4-LiCl-KCl melt revealed that 86.8% of Th(IV) can be separated from the melt based on the inductively coupled plasma atomic emission spectrometer (ICP-AES) results.

  8. Electrochemical behavior of uranium oxide in a LiCl-Li2O molten salt with the integrated cathode assembly

    International Nuclear Information System (INIS)

    Park, Sung Bin; Park, Byung Heung; Kang, Dae Seoung; Kwon, Seon Gil; Seo, Chung Seok; Park, Seong Won

    2005-01-01

    Electrochemical reduction of uranium oxide to uranium metal was studied in a LiCl-Li 2 O molten salt system. By means of a cyclic voltammetry and a chronopotentiometry, the electrolytic reduction of uranium oxide has been studied to establish the reduction mechanisms and the effects of the thickness of the uranium oxide on the overpotential of the cathode and anode were investigated. From the voltamograms, the reduction potentials of the uranium oxide and Li 2 O were obtained and the two mechanisms of the electrolytic reduction were considered with regards to the applied cathode potential. In the chronopotentiograms, the exchange current, the transfer coefficient and the maximum allowable current based on the Tafel behavior were obtained according to the thickness of the uranium oxide which is loaded into the porous MgO membrane. (author)

  9. Electrochemical corrosion behavior of MSIP Ni coating on depleted uranium surface

    International Nuclear Information System (INIS)

    Chen Lin; Li Kexue; Wang Qingfu; Wang Xiaohong; Guan Weijun

    2014-01-01

    The Ni film was prepared by magnetron sputtering ion plating to improve the corrosion resistance of depleted uranium. The corrosion resistance of the Ni film was examined by electrochemical corrosion station. The results show that the Ni film corrosion potential is -100.8 mV, whereas it is -641.2 mV for depleted uranium in 50 μg/g KCl solution. The Ni film is a barrier to protect the depleted uranium substrate avoiding the corrosive media attack. The Ni film polarization resistance and impedance are much higher, while the corrosion current density is much lower contrast with depleted uranium. None crack or flake is found through 70 h corrosion. The corrosion resistance and corrosion current keep stable. It is indicated that the corrosion resistance of depleted uranium is effectively improved after deposited Ni film by magnetron sputtering ion plating. (authors)

  10. Microstructures and Electrochemical Behavior of Ti-Mo Alloys for Biomaterials

    Directory of Open Access Journals (Sweden)

    Back-Sub Sung

    2015-01-01

    Full Text Available The Ti alloy with 7 wt% Mo revealed a microstructure that contained only the orthorhombic α′′ phase of a fine acicular martensitic structure. The corrosion resistance of the Ti-Mo alloys increased as the Mo content increased. Based on the results obtained from the polarization curve and electrochemical impedance, the Ti-Mo alloys were shown to be corrosion resistant because of the passive films formed on their surfaces. No ion release was detected in SBF (simulated body fluid solution, while Ti ions were released in 0.1% lactic acid ranging from 0.05 to 0.12 μg/mL for the Ti-Mo alloys. In vitro tests showed that MC3T3-E1 cell proliferation on Ti-7 wt% Mo alloy was rather active compared to other Ti-Mo alloys and commercial-grade pure Ti.

  11. Electrochemical reduction behavior of U3O8 powder in a LiCl molten salt

    International Nuclear Information System (INIS)

    Jeong, Sang Mun; Shin, Ho-Sup; Hong, Sun-Seok; Hur, Jin-Mok; Do, Jae Bum; Lee, Han Soo

    2010-01-01

    The reduction path of the U 3 O 8 powder vol-oxidized at 1200 deg. C has been determined by a series of electrochemical experiments in a 1 wt.% Li 2 O/LiCl molten salt. Various reaction intermediates are observed by during electrolysis of U 3 O 8 . The formation of the metallic uranium is caused from two different reduction paths, a direct reduction of uranium oxide and an electro-lithiothermic reduction. As the uranium oxide is converted to the metallic uranium, the lithium metal is more actively formed in the cathode basket. The reducibility of the rare earth oxides with the U 3 O 8 powder has been tested by constant voltage electrolysis. The results suggest the advanced vol-oxidation could lead to the enhancement in the reducibility of the rare earth fission products.

  12. Electrochemical behavior of TIO{sub 2} deposited stainless steel in high temperature water

    Energy Technology Data Exchange (ETDEWEB)

    Okamura, M.; Yamamoto, S. [Toshiba Corp., Kawasaki-city, Kanagawa (Japan); Urata, H.; Takagi, J. [Toshiba Corp., Yokohama-city, Kanagawa (Japan)

    2010-07-01

    It has previously been confirmed that the electrochemical corrosion potential (ECP) of stainless steel (SS) shifts in the negative direction by deposition of TiO{sub 2}. Recently we showed that TiO{sub 2} could decrease the ECP of SS in the absence of UV irradiation. In this study we measured the anodic polarization curve in high temperature water under UV irradiation and none irradiation condition and considered the mechanism of the ECP shift by TiO{sub 2} deposition. The anodic current density of the specimen increased with increasing the UV irradiation intensity and with increasing the amount of TiO{sub 2} deposition under none UV irradiation. Furthermore the oxide film of the specimen affects on the anodic current density was clarified. It was verified the ECP shift is caused by the anodic current density increasing with TiO{sub 2} deposition under both conditions of UV and none UV irradiation. (author)

  13. Microscopic Analysis and Electrochemical Behavior of Fe-Based Coating Produced by Laser Cladding

    Directory of Open Access Journals (Sweden)

    Jinlin Chen

    2017-10-01

    Full Text Available The effect of laser cladding on the surface microstructure and corrosion properties of coated/uncoated specimens were investigated. Fe-based alloy coating was produced on 35CrMo steel by laser cladding. The phase composition, microstructure, interface element distribution, microhardness and corrosion resistance of the cladding coating were measured. The results show that the cladding layer is mainly composed of α-Fe phases, the microstructure presents a gradient distribution, and a good metallurgical bond is formed at the boundary with the substrate. Microhardness profiles show that the average microhardness of the cladding coating is about 2.1 times higher than that of the uncoated specimen. In addition, the electrochemical results show that the coated specimen exhibits far better corrosion resistance than to the uncoated specimen.

  14. Effect of zinc crystals size on galvanized steel deformation and electrochemical behavior

    Directory of Open Access Journals (Sweden)

    José Daniel Culcasi

    2009-09-01

    Full Text Available Hot-dip galvanized steel sheets with different spangle sizes were deformed by means of rolling and tension. The change of preferential crystallographic orientation and of superficial characteristics due to the deformation was analyzed by means of both X-rays diffraction and optical and scanning electronic microscopy. A correlation between such changes and the involving deformation modes was intended to be done and the spangle size influence on these modes was studied. Coating reactivity change due to the deformation was investigated by means of quasi-steady DC electrochemical tests. The results allow to infer that, in great spangle samples, the main deformation mechanism is twinning whereas in small spangle ones, pyramidal slip systems happen as well. The increase of the reactivity with the deformation is greater in tension than in rolling and it is more important in small than in great spangle samples.

  15. Electrochemical fabrication and modelling of mechanical behavior of a tri-layer polymer actuator

    International Nuclear Information System (INIS)

    Kaynak, Akif; Yang Chunhui; Lim, Yang C.; Kouzani, Abbas

    2011-01-01

    Stability and performance of electrochemically synthesized tri-layer polypyrrole based actuators were reported. Concentrations were optimized as 0.05 M pyrrole and 0.05 M tetrabutylammonium hexaflurophosphate in propylene carbonate (PC). The force output of the actuators ranged from 0.2 to 0.4 mN. Cyclic deflection tests on PC based actuators for a duration of 3 h indicated that the displacement decreased by 60%. However, actuation could be regenerated by immersing the actuator into the electrolyte solution. Surface resistivity measurements on the actuators prior to and after 3 h continuous deflection did not show any significant change in the resistivity of the PPy layer. A triple-layer model of the polymer actuator was developed based on the classic bending beam theory by considering strain continuity between PPy and PVDF. Results predicted by the model were in good agreement with the experimental data.

  16. Determination of carnosic acid in Rosmarinus officinalis L. using square wave voltammetry and electrochemical behavior

    Directory of Open Access Journals (Sweden)

    Ümmihan Taşkoparan Yilmaz

    2018-01-01

    Full Text Available A new, fast, sensitive and simple voltammetric method is established for the direct determination of carnosic acid (CA. And the electroreduction of carnosic acid (CA was studied using electrochemical methods. The number of electrons transferred in electrode mechanisms were calculated for reversible and adsorption-controlled electrochemical reduction of CA at 17 mV versus Ag/AgCl at pH 7.0 in Britton–Robinson buffer (BR on a hanging mercury drop electrode. Square-wave voltammetry was developed and validated for direct determination of CA. Square-wave parameters were optimized as accumulation potential = 0.0 mV, accumulation time = 5 s, frequency = 50 Hz, pulse amplitude = 50 mV, and staircase step potential = 5 mV. The developed method displays three linear responses from 2 to 9 μM, 10 to 30 and 40 to 90 μM for carnosic acid with a correlation coefficient of 0.996, 0.999 and 0.999. The detection limits were found to be 1.5 μM, 4.0 μM and 40.1 μM, respectively. The interference effect of most common organic and inorganic species was investigated. Proposed method was successfully applied for determination of CA in natural extract of rosemary and the average content was determined as 11.9 ± 1.0 (μg CA/1 g rosemary. The results were in agreement with that obtained by HPLC-UV comparison method. The developed method can be widely used in routine quality control of herbal materials as well as other in foods, medicinal, pharmaceutical and environmental analysis.

  17. Synthesis, characterization and electrochemical behavior of Sb-doped ZnO microsphere film

    Energy Technology Data Exchange (ETDEWEB)

    Li, Qian [Department of Materials Science and Engineering, State Key Laboratory of Silicon Materials, Cyrus Tang Center for Sensor Materials and Applications, Zhejiang University, Hangzhou, 310027 (China); Cheng, Kui, E-mail: chengkui@zju.edu.cn [Department of Materials Science and Engineering, State Key Laboratory of Silicon Materials, Cyrus Tang Center for Sensor Materials and Applications, Zhejiang University, Hangzhou, 310027 (China); Weng, Wenjian, E-mail: wengwj@zju.edu.cn [Department of Materials Science and Engineering, State Key Laboratory of Silicon Materials, Cyrus Tang Center for Sensor Materials and Applications, Zhejiang University, Hangzhou, 310027 (China); The Shanghai Institute of Ceramics, Chinese Academy of Sciences, 1295 Dingxi Road, Shanghai, 200050 (China); Du, Piyi; Han, Gaorong [Department of Materials Science and Engineering, State Key Laboratory of Silicon Materials, Cyrus Tang Center for Sensor Materials and Applications, Zhejiang University, Hangzhou, 310027 (China)

    2013-10-01

    Sb-doped ZnO microsphere film was fabricated by a carboxylate ion assisted hydrothermal route coupled with a post-calcination process. The structure, chemical composition and optical band gap of the Sb-doped ZnO microsphere film were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, inductively couple plasma optical emission spectroscopy and UV–visible spectrophotometry, and compared with the un-doped ZnO microsphere film. The results suggest that the formation of zinc–antimony tartrate complex species during hydrothermal growth is the key to realize Sb-doped ZnO microstructures, and the present hydrothermal method with post-calcination is an effective way to dope Sb into ZnO. Furthermore, the Sb-doped ZnO microsphere film based electrochemical biosensor exhibits a good sensing performance for the detection of hydrogen peroxide, with a sensitivity of 271 μA mM{sup −1} cm{sup −2} which is more than three times higher than that of the un-doped ZnO biosensor. - Highlights: • Sb-doped ZnO microsphere (SZM) films were grown by hydrothermal deposition. • Carboxylate ions were used to form complex during hydrothermal growth. • The formation of Zn–Sb tartrate complex is the key to realize SZM. • The biosensors based on SZM film are feasible and sensitive to detect H{sub 2}O{sub 2}. • The Sb doping could improve the electrochemical property of ZnO.

  18. Adsorption behavior of redox-active suppressor additives: Combined electrochemical and STM studies

    International Nuclear Information System (INIS)

    Hai, N.T.M.; Huynh, T.M.T.; Fluegel, A.; Mayer, D.; Broekmann, P.

    2011-01-01

    Highlights: → Janus Green B and safranine are prototypical redox-active leveler additives for copper electroplating. → Their redox-transitions lie within the copper potential window. → Reduced additives are identified as active species for the leveling effect. → Electro-reduction affects in particular the central aromatic cores of the additives. - Abstract: The redox chemistry and the related surface phase behavior of Safranine (SAF) and Janus Green B (JGB) have been studied by means of cyclic voltammetry in combination with in situ Scanning Tunneling Microscopy using HOPG (Highly Oriented Pyrolytic Graphite) and single crystalline Cu(1 0 0) as model substrates, both revealing different widths of the accessible potential windows. JGB and SAF serve as prototypical heterocyclic suppressor/leveler additives that are used for the metallization of 3D-TSVs (3D Through Silicon Vias) following a classical 'leveling' concept. SAF can be considered as the reductive decomposition product of JGB that is formed at the copper/electrolyte interface upon electroplating. Both additives reveal a pronounced pH-dependent redox-chemistry with redox-transitions lying close to or even beyond the anodic limit of the copper potential window. Affected by these redox-processes are in particular the aromatic cores of those heterocycles that can be (quasi)reversibly reduced by a two electron transfer process within the potential window of copper. Therefore we identify the reduced form of those dyes as the active components for the suppressing/leveling effect in copper plating. STM data clearly shows a dye surface phase behavior that is crucially determined by its potential-dependent redox-chemistry. This will be exemplarily discussed for the SAF dye. On chloride-modified Cu(1 0 0) mono-reduced SAF forms a structurally well-defined monolayer of cationic stacking polymers. However, this coupled anion/cation layer reveals only minor suppressing capabilities with respect to the copper

  19. Technical report for fabrication and performance test of electrochemical/spectroscopic measurement system

    International Nuclear Information System (INIS)

    Park, Yong Joon; Cho, Young Hwan; Bae, Sang Eun; Im, Hee Jung; Song, Kyu Seok

    2010-01-01

    Development of evaluation technology of electrochemical reactions is very essential to understand chemical behavior of actinides and lanthanides in molten salt media in relation to the development of Pyrochemical process. The on-line electrochemical/spectroscopic measurement system is to produce electrochemical parameters and thermodynamic parameters of actinides and lanthanides in molten salts by using spectroscopic techniques such as UV-VIS absorption as well as electrochemical in-situ measurement techniques. The on-line electrochemical/spectroscopic measurement system can be applied to understand the chemical reactions and oxidation states of actinides and lanthanides in molten salts eventually for the Pyrochemical process

  20. Electrochemical behavior of NixW1−x materials as catalyst for hydrogen evolution reaction in alkaline media

    International Nuclear Information System (INIS)

    Oliver-Tolentino, Miguel A.; Arce-Estrada, Elsa M.; Cortés-Escobedo, Claudia A.; Bolarín-Miro, Ana M.; Sánchez-De Jesús, Félix; González-Huerta, Rosa de G.; Manzo-Robledo, Arturo

    2012-01-01

    Highlights: ► The electrochemical techniques used in this study elucidated the Ni–W surface state. ► The Ni–W materials were effective for the hydrogen evolution reaction. ► The prepared alloys exhibited higher catalytic activity than their precursors. ► The preparation method is relatively simple and effective procedure. - Abstract: In the present work, results of electrochemical evaluation, as well as morphological and structural characterization of Ni x W 1−x materials with x = 0.77, 0.64, 0.4, 0.19 and 0.07 processed by means of high energy ball milling from high purity powders are presented. Also, the electrocatalytic performance on the hydrogen evolution reaction (HER) of the Ni x W 1−x materials evaluated by linear polarization and cyclic voltammetry techniques in alkaline media at room temperature is discussed. The structural and morphological characterization of the as-prepared materials was carried out using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results indicated a small-particle clusters and solid solution formation. According to the kinetics parameters the best electrocatalytic activity was observed at Ni 64 W 36 .

  1. Electrochemical behavior and biological response of Mesenchymal Stem Cells on cp-Ti after N-ions implantation

    Energy Technology Data Exchange (ETDEWEB)

    Rizwan, M.; Ahmad, A. [Department of Metallurgical and Materials Engineering, University of Engineering and Technology, 54890 Lahore (Pakistan); Deen, K.M. [Corrosion Control Research Cell, Department of Metallurgy and Materials Engineering, CEET, University of the Punjab, 54590 Lahore (Pakistan); Haider, W., E-mail: haiderw@utpa.edu [Mechanical Engineering Department, University of Texas Pan American, Edinburg, TX 78539 (United States)

    2014-11-30

    Highlights: • Nitrogen ions of known dosage were implanted on cp-Ti. • Increase in surface roughness with increase in ions dose was confirmed by AFM. • TiN{sub 0.3} and Ti{sub 3}N{sub 2−x} nitride phases were formed and validated by XRD. • The ions implantation reduced the corrosion rate and stabilized the passive film. • Surface roughness greatly affected the morphology and growth of Mesenchymal Stem Cells. - Abstract: Titanium and its alloys are most widely used as implant materials due to their excellent biocompatibility, mechanical properties and chemical stability. In this study Nitrogen ions of known dosage were implanted over cp-Ti by Pelletron accelerator with beam energy of 0.25 MeV.The atomic force microscopy of bare and nitrogen implanted specimens confirmed increase in surface roughness with increase in nitrogen ions concentration. X-ray diffraction patterns of ions implanted surfaces validated the formation of TiN{sub 0.3} and Ti{sub 3}N{sub 2-x}nitride phases. The tendency to form passive film and electrochemical behavior of these surfaces in ringer lactate (RL) solution was evaluated by Potentiodynamic polarization and electrochemical impedance spectroscopy respectively. It is proved that nitrogen ions implantation was beneficial to reduce corrosion rate and stabilizing passive film by increasing charge transfer resistance in RL. It was concluded that morphology and proliferation of Mesenchymal Stem Cells on nitrogen ions implanted surfaces strongly depends on surface roughness and nitride phases.

  2. Stability, electrochemical behaviors and electronic structures of iron hydroxyl-phosphate

    Energy Technology Data Exchange (ETDEWEB)

    Wang Zhongli; Sun Shaorui; Li Fan; Chen Ge [College of Environmental and Energy Engineering, Beijing University of Technology, Pingleyuan 100, Chaoyang District, Beijing 100022 (China); Xia Dingguo, E-mail: dgxia@bjut.edu.cn [College of Environmental and Energy Engineering, Beijing University of Technology, Pingleyuan 100, Chaoyang District, Beijing 100022 (China); Zhao Ting; Chu Wangsheng [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); University of Science and Technology of China, Hefei 230026 (China); Wu Ziyu, E-mail: wuzy@ihep.ac.cn [Institute of High Energy Physics, Chinese Academy of Sciences, Beijing 100049 (China); University of Science and Technology of China, Hefei 230026 (China)

    2010-09-01

    Iron hydroxyl-phosphate with a uniform spherical particle size of around 1 {mu}m, a compound of the type Fe{sub 2-y}{open_square}{sub y}(PO{sub 4})(OH){sub 3-3y}(H{sub 2}O){sub 3y-2} (where {open_square} represents a vacancy), has been synthesized by hydrothermal methods. The particles are composed of spheres of diameter <100 nm. The compound exhibits good electrochemical performance, with reversible capacities of around 150 mAh g{sup -1} and 120 mAh g{sup -1} at current densities of 170 mA g{sup -1} and 680 mA g{sup -1}, respectively. The stability of crystal structure of this material was studied by TGA and XRD which show that the material remains stable at least up to the temperature 200 deg. C. Investigation of the electronic structure of the iron hydroxyl-phosphate by GGA + U calculation has indicated that it has a better electronic conductivity than LiFePO{sub 4}.

  3. Electrochemical behavior and pH stability of artificial salivas for corrosion tests.

    Science.gov (United States)

    Queiroz, Gláucia Maria Oliveira de; Silva, Leandro Freitas; Ferreira, José Tarcísio Lima; Gomes, José Antônio da Cunha P; Sathler, Lúcio

    2007-01-01

    It is assumed that the compositions of artificial salivas are similar to that of human saliva. However, the use of solutions with different compositions in in vitro corrosion studies can lead dissimilar electrolytes to exhibit dissimilar corrosivity and electrochemical stability. This study evaluated four artificial salivas as regards pH stability with time, redox potentials and the polarization response of an inert platinum electrode. The tested solutions were: SAGF medium, Mondelli artificial saliva, UFRJ artificial saliva (prepared at the School of Pharmacy, Federal University of Rio de Janeiro, RJ, Brazil) and USP-RP artificial saliva (prepared at the School of Pharmaceutical Sciences of Ribeirão Preto, University of São Paulo, SP, Brazil). It was observed that pH variations were less than 1 unit during a 50-hour test. The SAGF medium, and the UFRJ and USP-RP solutions exhibited more oxidizing characteristics, whereas the Mondelli solution presented reducing properties. Anodic polarization revealed oxidation of the evaluated electrolytes at potentials below +600 mV SCE. It was observed that the UFRJ and USP-RP solutions presented more intense oxidation and reduction processes as compared to the Mondelli and SAGF solutions.

  4. Electrochemical behavior of Ni-Mo electro catalyst for water electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez V, S. M.; Ordonez R, E. [ININ, Departamento de Quimica, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico); Cabanas M, G. [IPN, Centro de Nanociencias y Micro y Nanotecnologias, A. P. 75-874, 07300 Mexico D. F. (Mexico); Solorza F, O., E-mail: suilma.fernandez@inin.gob.m [IPN, Centro de Investigacion y de Estudios Avanzados, Departamento de Quimica, A. P. 14-740, 07000 Mexico D. F. (Mexico)

    2010-07-01

    Nickel-molybdenum based electrocatalysts were synthesized in organic media for the hydrogen evolution reaction and oxygen evolution reaction in alkaline media. The structure, morphology and chemical composition of the catalysts were evaluated by X-ray diffraction, scanning electron microscopy and Aas. Results revealed nanocrystalline powder materials with Ni{sub 0.006}Mo, Ni{sub 0.1}Mo and Ni Mo compositions. The best performance for hydrogen evolution reaction, was obtained on Ni{sub 0.1}Mo electrode, whereas Ni Mo was for the oxygen evolution reaction. Results suggest that the material with 1:1 stoichiometric ratio could be considered as a promising electro catalyst for oxygen evolution reaction. This nanocrystalline powder is formed by Ni{sub 2}Mo{sub 3}O{sub 8} and a crystalline structure attributed to the possible formation of a Ni Mo cluster, becomes NiMoO{sub 4} after thermal treatment at 1073 K in air. The Ni Mo 1:1 cluster catalyst presented electrochemical stability during the oxygen evolution reaction. (Author)

  5. Electrochemical behavior of Ni-Mo electro catalyst for water electrolysis

    International Nuclear Information System (INIS)

    Fernandez V, S. M.; Ordonez R, E.; Cabanas M, G.; Solorza F, O.

    2010-01-01

    Nickel-molybdenum based electrocatalysts were synthesized in organic media for the hydrogen evolution reaction and oxygen evolution reaction in alkaline media. The structure, morphology and chemical composition of the catalysts were evaluated by X-ray diffraction, scanning electron microscopy and Aas. Results revealed nanocrystalline powder materials with Ni 0.006 Mo, Ni 0.1 Mo and Ni Mo compositions. The best performance for hydrogen evolution reaction, was obtained on Ni 0.1 Mo electrode, whereas Ni Mo was for the oxygen evolution reaction. Results suggest that the material with 1:1 stoichiometric ratio could be considered as a promising electro catalyst for oxygen evolution reaction. This nanocrystalline powder is formed by Ni 2 Mo 3 O 8 and a crystalline structure attributed to the possible formation of a Ni Mo cluster, becomes NiMoO 4 after thermal treatment at 1073 K in air. The Ni Mo 1:1 cluster catalyst presented electrochemical stability during the oxygen evolution reaction. (Author)

  6. The improvement of SiO2 nanotubes electrochemical behavior by hydrogen atmosphere thermal treatment

    Science.gov (United States)

    Spataru, Nicolae; Anastasescu, Crina; Radu, Mihai Marian; Balint, Ioan; Negrila, Catalin; Spataru, Tanta; Fujishima, Akira

    2018-06-01

    Highly defected SiO2 nanotubes (SiO2-NT) were obtained by a simple sol-gel procedure followed by calcination. Boron-doped diamond (BDD) polycrystalline films coated with SiO2-NT were used as working electrodes and, unexpectedly, cyclic voltammetric experiments have shown that the concentration of both positive and negative defects at the surface is high enough to enable redox processes involving positively charged Ru(bpy)32+/3+ to occur. Conversely, no electrochemical activity was put into evidence for Fe(CN)63-/4- species, most likely as a result of the strong electrostatic repulsion exerted by the negatively charged SiO2 surface. The concentration of surface defects was further increased by a subsequent thermal treatment in a hydrogen atmosphere which, as EIS measurements have shown, significantly promotes Ru(bpy)32+ anodic oxidation. Digital simulation of the voltammetric responses demonstrated that this treatment does not lead to a similar increase of the number of electron-donor sites. It was also found that methanol anodic oxidation at hydrogenated SiO2-NT-supported platinum results in Tafel slopes of 116-220 mV decade-1, comparable to those reported for both conventional PtRu and Pt-oxide catalysts.

  7. Electrochemical behavior of polypyrrole/chitosan composite coating on Ti metal for biomedical applications.

    Science.gov (United States)

    Rikhari, Bhavana; Pugal Mani, S; Rajendran, N

    2018-06-01

    In the present work, the corrosion resistance performance and biocompatibility of polypyrrole/chitosan (PPy/CHI) composite coated Ti was studied. The deposition of composite coating was carried out by electropolymerization method. The deposited PPy/CHI composite coatings were different in morphology, structural, surface roughness and wettability compared PPy coated Ti. The presence of composite coating was confirmed by solid 13 C NMR. The PPy/CHI composite coating showed enhanced microhardness and adhesion strength compared to the PPy coating. The corrosion protection ability of PPy/CHI composite coatings at various applied potentials was analyzed by dynamic electrochemical impedance spectroscopy (DEIS), exhibited higher impedance in all the potentials compared to uncoated and PPy coated Ti. The lower corrosion current density obtained for PPy/CHI-2 composite coating from polarization studies revealed increased corrosion protection ability in SBF solution. The stability of composite coating was confirmed by immersion studies. PPy/CHI-2 composite coating immersed in SBF solution enhances hydroxyapatite (HAp) formation. Copyright © 2018 Elsevier Ltd. All rights reserved.

  8. Dopamine Signaling in reward-related behaviors

    OpenAIRE

    Baik, Ja-Hyun

    2013-01-01

    Dopamine (DA) regulates emotional and motivational behavior through the mesolimbic dopaminergic pathway. Changes in DA mesolimbic neurotransmission have been found to modify behavioral responses to various environmental stimuli associated with reward behaviors. Psychostimulants, drugs of abuse, and natural reward such as food can cause substantial synaptic modifications to the mesolimbic DA system. Recent studies using optogenetics and DREADDs, together with neuron-specific or circuit-specifi...

  9. Environment-friendly cathodes using biopolymer chitosan with enhanced electrochemical behavior for use in lithium ion batteries.

    Science.gov (United States)

    Prasanna, K; Subburaj, T; Jo, Yong Nam; Lee, Won Jong; Lee, Chang Woo

    2015-04-22

    The biopolymer chitosan has been investigated as a potential binder for the fabrication of LiFePO4 cathode electrodes in lithium ion batteries. Chitosan is compared to the conventional binder, polyvinylidene fluoride (PVDF). Dispersion of the active material, LiFePO4, and conductive agent, Super P carbon black, is tested using a viscosity analysis. The enhanced structural and morphological properties of chitosan are compared to the PVDF binder using X-ray diffraction analysis (XRD) and field emission scanning electron microscopy (FE-SEM). Using an electrochemical impedance spectroscopy (EIS) analysis, the LiFePO4 electrode with the chitosan binder is observed to have a high ionic conductivity and a smaller increase in charge transfer resistance based on time compared to the LiFePO4 electrode with the PVDF binder. The electrode with the chitosan binder also attains a higher discharge capacity of 159.4 mAh g(-1) with an excellent capacity retention ratio of 98.38% compared to the electrode with the PVDF binder, which had a discharge capacity of 127.9 mAh g(-1) and a capacity retention ratio of 85.13%. Further, the cycling behavior of the chitosan-based electrode is supported by scrutinizing its charge-discharge behavior at specified intervals and by a plot of dQ/dV.

  10. Electrochemical behavior of Ti and Ti6Al4V in aqueous solutions of citric acid containing halides

    Directory of Open Access Journals (Sweden)

    Anelise Marlene Schmidt

    2006-12-01

    Full Text Available This paper reports on an investigation of the electrochemical behavior of Ti grade 2 and Ti6Al4V alloy in aqueous citric acid solutions with pH 2.0 containing halide ions. Voltammetric studies of Ti and the alloy in citric acid, with and without chloride ions, indicate that the Ti and Ti alloy presented a passive behavior in the test solutions used. Pitting was observed at 3.0 and 2.5 V/SCE for Ti and Ti6Al4V, respectively, when bromide ions were added to the solution. In solutions containing fluoride ions, dissolution of the film occurred at potentials close to - 1.0 V/SCE in both electrodes. The iodide ions oxidized on the passive oxide film at potentials close to 1.0 V/SCE. EIS results of the materials in citric acid solutions containing chloride ions revealed that the film's resistance increased as the applied potential rose from 0 to 1.0 V. In bromide-containing solutions, breakdown of the film was confirmed at potentials above 2.0 V/SCE in both electrodes. These results suggest film reformation for Ti and the alloy in solutions containing fluoride at potentials within the passive region.

  11. Distinctive colonization of Bacillus sp. bacteria and the influence of the bacterial biofilm on electrochemical behaviors of aluminum coatings.

    Science.gov (United States)

    Abdoli, Leila; Suo, Xinkun; Li, Hua

    2016-09-01

    Formation of biofilm is usually essential for the development of biofouling and crucially impacts the corrosion of marine structures. Here we report the attachment behaviors of Bacillus sp. bacteria and subsequent formation of bacterial biofilm on stainless steel and thermal sprayed aluminum coatings in artificial seawater. The colonized bacteria accelerate the corrosion of the steel plates, and markedly enhance the anti-corrosion performances of the Al coatings in early growth stage of the bacterial biofilm. After 7days incubation, the biofilm formed on the steel is heterogeneous while exhibits homogeneous feature on the Al coating. Atomic force microscopy examination discloses inception of formation of local pitting on steel plates associated with significantly roughened surface. Electrochemical testing suggests that the impact of the bacterial biofilm on the corrosion behaviors of marine structures is not decided by the biofilm alone, it is instead attributed to synergistic influence by both the biofilm and physicochemical characteristics of the substratum materials. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. Electrochemical and surface behavior of hydyroxyapatite/Ti film on nanotubular Ti-35Nb-xZr alloys

    International Nuclear Information System (INIS)

    Jeong, Yong-Hoon; Choe, Han-Cheol; Brantley, William A.

    2012-01-01

    In this paper, we investigated the electrochemical and surface behavior of hydroxyapatite (HA)/Ti films on the nanotubular Ti-35Nb-xZr alloy. The Ti-35Nb-xZr ternary alloys with 3-10 wt.% Zr content were made by an arc melting method. The nanotubular oxide layers were developed on the Ti-35Nb-xZr alloys by an anodic oxidation method in 1 M H 3 PO 4 electrolyte containing 0.8 wt% NaF at room temperature. The HA/Ti composite films on the nanotubular oxide surfaces were deposited by a magnetron sputtering method. Their surface characteristics were analyzed by field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS) and an X-ray diffractometer (XRD). The corrosion behavior of the specimens was examined through potentiodynamic and AC impedance tests in 0.9% NaCl solution. From the results, the Ti-35Nb-xZr alloys showed a solely β phase microstructure that resulted from the addition of Zr. The nanotubular structure formed with a diameter of about 200 nm, and the HA/Ti thin film was deposited on the nanotubular structure. The HA/Ti thin film-coated nanotubular Ti-35Nb-xZr alloys showed good corrosion resistance in 0.9% NaCl solution.

  13. Electrochemical potential measurements in boiling water reactors; relation to water chemistry and stress corrosion

    International Nuclear Information System (INIS)

    Indig, M.E.; Cowan, R.L.

    1981-01-01

    Electrochemical potential measurements were performed in operating boiling water reactors to determine the range of corrosion potentials that exist from cold standby to full power operation and the relationship of these measurements to reactor water chemistry. Once the corrosion potentials were known, experiments were performed in the laboratory under electrochemical control to determine potentials and equivalent dissolved oxygen concentrations where intergranular stress corrosion cracking (IGSCC) would and would not occur on welded Type-304 stainless steel. At 274 0 C, cracking occurred at potentials that were equivalent to dissolved oxygen concentration > 40 to 50 ppb. With decreasing temperature, IGSCC became more difficult and only severely sensitized stainless steel would crack. Recent in-reactor experiments combined with the previous laboratory data, have shown that injection of small concentrations of hydrogen during reactor operation can cause a significant decrease in corrosion potential which should cause immunity to IGSCC. (author)

  14. Dopamine signaling in reward-related behaviors.

    Science.gov (United States)

    Baik, Ja-Hyun

    2013-01-01

    Dopamine (DA) regulates emotional and motivational behavior through the mesolimbic dopaminergic pathway. Changes in DA mesolimbic neurotransmission have been found to modify behavioral responses to various environmental stimuli associated with reward behaviors. Psychostimulants, drugs of abuse, and natural reward such as food can cause substantial synaptic modifications to the mesolimbic DA system. Recent studies using optogenetics and DREADDs, together with neuron-specific or circuit-specific genetic manipulations have improved our understanding of DA signaling in the reward circuit, and provided a means to identify the neural substrates of complex behaviors such as drug addiction and eating disorders. This review focuses on the role of the DA system in drug addiction and food motivation, with an overview of the role of D1 and D2 receptors in the control of reward-associated behaviors.

  15. Dopamine Signaling in reward-related behaviors

    Directory of Open Access Journals (Sweden)

    Ja-Hyun eBaik

    2013-10-01

    Full Text Available Dopamine (DA regulates emotional and motivational behavior through the mesolimbic dopaminergic pathway. Changes in DAmesolimbic neurotransmission have been found to modify behavioral responses to various environmental stimuli associated with reward behaviors. Psychostimulants, drugs of abuse, and natural rewards such as food can cause substantial synaptic modifications to the mesolimbic DA system. Recent studies using optogenetics and DREADDs, together with neuron-specific or circuit-specific genetic manipulations have improved our understanding of DA signaling in the reward circuit, and provided a means to identify the neural substrates of complex behaviors such as drug addiction and eating disorders. This review focuses on the role of the DA system in drug addiction and food motivation, with an overview of the role of D1 and D2 receptors in the control of reward-associated behaviors.

  16. Developing a Behavioral Paradigm for the Performance of Public Relations.

    Science.gov (United States)

    Sharpe, Melvin L.

    2000-01-01

    Provides and supports a definition of public relations as behavior with a mode explaining the difficulty of achieving each behavior and the cost to organizations when the behavior is not achieved. Draws from the literature on ethics, rhetorical theory, public relations management, case studies, and from observation and experience to support this…

  17. RELATION OF COACHING BEHAVIOR AND ROLE AMBIGUITY

    Directory of Open Access Journals (Sweden)

    Karamousalidis G.

    2010-08-01

    Full Text Available The purpose of this research was to investigate the relationship between coaching behavior and role ambiguity in defensive responsibilities using interdependent Greek sport teams. Athlete perceptions of role ambiguity (defense were assessed using a questionnaire developed by Beauchamp, Bray, Eys and Carron (2002 andcoaching behavior was assessed using the Coaching Behavior Questionnaire, (Williams, et. al., 2003. The sample consisted of 409 athletes of basketball, volleyball, handball and soccer. Confirmatory factor analysis provided the construct validity of the questionnaires and correlations among the scales confirmed construct validity. The implications of the results are discussed and future research should continue to investigate the multidimensional models of both coaching behavior and role ambiguity in sport settings.

  18. Electrochemical and corrosion behavior of two chromium dental alloys in artificial bioenvironments

    Directory of Open Access Journals (Sweden)

    Banu Alexandra

    2017-01-01

    Full Text Available The purpose of this study is to compare the corrosion and tarnish behavior of NiCrMo and CoCrMo cast dental alloys in artificial bio environments. The cobalt chromium alloys are known and used in dentistry for many years, but its difficult machinability because of the strength and hardness, is an argument for scientists to study alternative materials with comparable biocompatibility. On the other hand, for dentistry devices beside corrosion behavior is important the aesthetic so, the used alloys have to preserve their shining and do not stain. The corrosion resistance has been evaluated using the Atomic mass spectroscopy method for ion release determination, the anodic polarization curves and the open circuit potential – time monitoring for corrosion behavior evaluation and optical microscopy for the structure analysis. The tarnish tendency of alloys was estimated using the method of cyclic immersion with frequency of 10 seconds for each minute during 72 hours in Na2S containing solution. The most important conclusion is that the alloys are comparable from corrosion and tarnish point of view, but we recommend to use the nickel base alloy only for orthodontic devices implanted for short periods of time, because of higher quantity of released ions.

  19. Standard practice for calculation of corrosion rates and related information from electrochemical measurements

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1989-01-01

    1.1 This practice covers the providing of guidance in converting the results of electrochemical measurements to rates of uniform corrosion. Calculation methods for converting corrosion current density values to either mass loss rates or average penetration rates are given for most engineering alloys. In addition, some guidelines for converting polarization resistance values to corrosion rates are provided. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

  20. In Situ TEM Investigation of the Electrochemical Behavior in CNTs/MnO2-Based Energy Storage Devices.

    Science.gov (United States)

    Tsai, Tsung-Chun; Huang, Guan-Min; Huang, Chun-Wei; Chen, Jui-Yuan; Yang, Chih-Chieh; Tseng, Tseung-Yuen; Wu, Wen-Wei

    2017-09-19

    Transition metal oxides have attracted much interest owing to their ability to provide high power density in lithium batteries; therefore, it is important to understand the electrochemical behavior and mechanism of lithiation-delithiation processes. In this study, we successfully and directly observed the structural evolution of CNTs/MnO 2 during the lithiation process using transmission electron microscopy (TEM). CNTs/MnO 2 were selected due to their high surface area and capacitance effect, and the lithiation mechanism of the CNT wall expansion was systematically analyzed. Interestingly, the wall spacings of CNTs/MnO 2 and CNTs were obviously expanded by 10.92% and 2.59%, respectively. The MnO 2 layer caused structural defects on the CNTs surface that could allow penetration of Li + and Mn 4+ through the tube wall and hence improve the ionic transportation speed. This study provided direct evidence for understanding the role of CNTs/MnO 2 in the lithiation process used in lithium ion batteries and also offers potential benefits for applications and development of supercapacitors.

  1. Justice- and fairness-related behaviors in nonhuman primates.

    Science.gov (United States)

    Brosnan, Sarah F

    2013-06-18

    A distinctive feature across human societies is our interest in justice and fairness. People will sometimes invest in extremely costly behavior to achieve fair outcomes for themselves and others. Why do people care so much about justice? One way to address this is comparatively, exploring behaviors related to justice and fairness in other species. In this paper, I review work exploring responses to inequity, prosocial behavior, and other relevant behaviors in nonhuman primates in an effort to understand both the potential evolutionary function of these behaviors and the social and ecological reasons for the individual differences in behavior. I also consider how these behaviors relate to human behavior, particularly in the case of experimental studies using games derived from experimental economics to compare nonhuman primates' responses to those of humans in similar experimental conditions. These results emphasize the importance of a comparative approach to better understand the function and diversity of human behavior.

  2. Influence of enzymatic reactions on the electrochemical behavior of EN X2CrNiMo17-11-2 (AISI 316L) stainless steel in bio-corrosion: role of interfacial processes on the modification of the passive layer

    International Nuclear Information System (INIS)

    Landoulsi, J.

    2008-01-01

    The outstanding corrosion behavior of stainless steels (SS) results from the presence of thin oxide layer (some nanometers). In non sterile aqueous media, stainless steels may exhibit a non stable behavior resulting from interactions between microbial species and passive film. In fact, microorganisms can be deeply involved in the corrosion processes usually reported as Microbial Influenced Corrosion (MIC). They can induce the initiation or the acceleration of this phenomenon and they do so when organized in bio-films. From the electrochemical point of view, stainless steels showed an increase of the free corrosion potential (Ecorr) attributed to the bio-film settlement. The Eco' ennoblement was broadly reported in seawater and seems to be confirmed in fresh water according to recent findings. A considerable progress in the comprehension of MIC processes was related to the role of extracellular species, essentially enzymes. Many enzymatic reactions occurring in bio-films consist on using oxygen as electron acceptor to generate hydrogen peroxide and related species. The aim of this work is to understand the mechanisms involved in the electrochemical behavior of stainless steel according to an enzymatic approach in medium simulating fresh water. To this end, glucose oxidase was chosen to globalize aerobic activities of bio-films. Electrochemical measurements in situ and surface analysis allow the comprehension of the role and the nature of interfacial processes. Surface characterization was performed with the help of a new quantitative utilization of XPS analysis and AFM. Results show a significant evolution in term of morphology (surface organization), (ii) chemical composition (passive layer, adsorbed organic species) and (iii) chemical reaction (oxidation, dissolution, effect of enzyme). Finally, a new enzymatic system is proposed to mimic specific physicochemical conditions at the SS / bio-film interface, in particular enzymatic generation of oxidant species in

  3. Droplet electrochemical study of the pH dependent redox behavior of novel ferrocenyl-carborane derivatives and its application in specific cancer cell recognition

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Changyu [State Key Laboratory of Bioelectronics (Chien-Shiung Wu Laboratory), Southeast University, Nanjing 210096 (China); Shah, Afzal [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Ye, Hongde [State Key Laboratory of Coordination Chemistry, Nanjing University, Nanjing 210093 (China); Chen, Xiao; Ye, Jing; Jiang, Hui [State Key Laboratory of Bioelectronics (Chien-Shiung Wu Laboratory), Southeast University, Nanjing 210096 (China); Chen, Baoan [Department of Hematology, the Affiliated Zhongda Hospital, Clinical Medical School, Southeast University, Nanjing 210009 (China); Wang, Xuemei, E-mail: xuewang@seu.edu.cn [State Key Laboratory of Bioelectronics (Chien-Shiung Wu Laboratory), Southeast University, Nanjing 210096 (China); Yan, Hong, E-mail: hyan1965@nju.edu.cn [State Key Laboratory of Coordination Chemistry, Nanjing University, Nanjing 210093 (China)

    2015-02-01

    Highlights: • Electrochemical behaviors of novel ferrocenyl based carboranes (FcCB) were explored with a droplet system. • The shifts of peak potentials with changes of pH values indicated the involvement of proton during electron transfer reaction. • Normal cells and cancer cells could be specifically recognized by using FcCB as probe. • This electrochemical method in a droplet shows great potential application for relevant diagnostics of clinical samples. - Abstract: Novel ferrocenyl based carboranes (FcCBs) and their distinguish behavior for cancer cell recognition have been explored in this contribution. The voltammetric study in a droplet of 10 μL placed on the surface of a glassy carbon electrode demonstrates the excellent electrochemical behavior of FcCBs, which could be further exploited for establishing the promising and sensitive biosensors. The FcCBs’ redox behavior is examined in a wide pH range, and square wave voltammetry revealed the reversible and irreversible nature of first and second anodic peaks. The obvious shifts in peak potentials corresponding with the change of pH values demonstrate the abstraction of electrons to be accompanied with the transfer of protons. By using the droplet electrochemical technique, FcCBs can be employed to distinguish normal and cancer cells with a linear range from 1.0 × 10{sup 3} to 3.0 × 10{sup 4} cells mL{sup −1} and the limit of detection at 800 cells mL{sup −1}. The novel carborane derivatives could be utilized as important potential molecular probes for specific recognition of cancer cells like leukemia cells from normal cells.

  4. Electrochemical corrosion behavior of A 516 steel using corrosive environments with varying concentrations of sodium thiosulphate

    International Nuclear Information System (INIS)

    Karim, F.; Arif, M.; Reza, I.; Akram, M.; Hussain, N.; Ali, L.

    2012-01-01

    The corrosion behavior of A 516 steel was studied by potentiodynamic polarization technique. Environment used for these tests was sodium chloride (5%), acetic acid (0.5%) and sodium thiosulphate with varying concentration from 0.001 M to 1 M. Surface study was also carried out using optical microscope. The potentiodynamic polarization results revealed the formation of large number of pits in the sample, which was tested in the solution containing NaCl. Pitting corrosion study of alloy A516 G-70 was also conducted to see the effect of different concentrations of thiosulfate with or without addition of NaCl and acetic acid at room temperature. It was observed that different thiosulfate concentrations did not produce any difference in the polarization behavior of the alloys, when added in 5% NaCl and 0.5% acetic acid solution. However, in the absence of NaCl and acetic acid, thiosulfate concentration 0.001 mol/l or higher did produce general corrosion and pitting in the alloy at room temperature is shown.(Orig./A.B.)

  5. Parenting style, parenting stress, and children's health-related behaviors.

    Science.gov (United States)

    Park, Hyunjeong; Walton-Moss, Benita

    2012-07-01

    Parental guidance is critical to the development of children's health-related behaviors. The purpose of this study was to look at the relationship between parenting factors, including parenting style and parenting stress, and children's health-related behaviors. In this descriptive, correlational study, 284 parents of preschool children were interviewed using the Child Rearing Questionnaire and the Korean Parenting Stress Index-Short Form. Parent distress, authoritative and permissive parenting styles, family income, and mother's education were significantly associated with children's health-related behaviors. These findings suggest that higher levels of warmth, characteristics of both parenting styles, may be a critical factor in the development of health-related behaviors.

  6. Teacher Behavioral Practices: Relations to Student Risk Behaviors, Learning Barriers, and School Climate

    Science.gov (United States)

    Martinez, Andrew; Mcmahon, Susan D.; Coker, Crystal; Keys, Christopher B.

    2016-01-01

    Student behavioral problems pose a myriad of challenges for schools. In this study, we examine the relations among teacher and school-level constructs (i.e., teacher collaboration, supervision/discipline, instructional management), and student-related outcomes (i.e., high-risk behaviors, barriers to learning, student social-behavioral climate).…

  7. Parental influence on children's oral health-related behavior.

    Science.gov (United States)

    Poutanen, Raija; Lahti, Satu; Tolvanen, Mimmi; Hausen, Hannu

    2006-10-01

    The aim of this study was to determine whether there are differences between oral health-related knowledge, attitudes, beliefs and behaviors of children and their parents, and to identify the family-related factors associated with children's poor or good oral health-related behavior. The data were gathered by means of questionnaires from 11-12-year-old schoolchildren and their parents who replied without having knowledge of the answers of the others. Differences between subgroups of children were analyzed by cross-tabulation, and the factors related to children's good or poor oral health-related behavior by logistic regression analyses. Parents of children who reported good oral health-related behavior had better knowledge and more favorable behaviors than those of other parents. Predictors for a child's poor oral health-related behavior were the child's poor knowledge, male gender, the parent's frequent consumption of sweets, and the parent's infrequent use of xylitol gum. When a less strict threshold for the child's poor oral health-related behavior was used, more predictors entered the model: the parent's unfavorable use of fluoride toothpaste; among girls, the parent's lack of knowledge; and among children whose mother's occupation level was high, the parent's infrequent use of xylitol gum. The parents of children whose oral health behavior was favorable were more likely to have a high level occupation and favorable oral health-related behaviors. Oral health-related knowledge of children and their parents seems to be associated with children's oral health-related behavior. Parents' behaviors, but not attitudes, were associated with children's oral health behavior.

  8. Comparison of Corrosion Behavior of Electrochemically Deposited Nano-Cobalt-Coated Ni Sheet

    Directory of Open Access Journals (Sweden)

    Nasser Al-Aqeeli

    2013-01-01

    Full Text Available Corrosion behavior of nano-coblat-coated Ni sheet was compared with pure Ni and 20% Fe-Ni alloy sheet using potentiodynamic polarization and linear polarization technique in 0.1 M NaCl solution at room temperature. Results showed that corrosion resistance properties of nano-Co-coated Ni sheet were almost same as that of pure Ni sheet, however corrosion resistance of 20% Fe-Ni sheet was decreased significantly. Pitting potential of 20% Fe-Ni sheet was subsequently decreased as compared to pure Ni sheet as well as nano-cobalt-coated Ni sheet. SEM/EDS analysis of the corroded surfaces showed that both pure Ni and nano-coblat-coated Ni sheet did not show any appreciable corrosion however significant corrosion was observed in the case of 20% Fe-Ni sheet.

  9. Highly conductive alumina/NCN composites electrodes fabricated by gelcasting and reduction-sintering-An electrochemical behavior study in aggressive environments

    International Nuclear Information System (INIS)

    Liu Jingjun; Menchavez, Ruben L.; Watanabe, Hideo; Fuji, Masayoshi; Takahashi, Minoru

    2008-01-01

    A novel highly conductive alumina/nano-carbon network composites (alumina/NCN composites) was fabricated by gelcasting and reduction-sintering method under argon atmosphere. The electrochemical behaviors of the alumina/NCN composites were studied systematically in some aggressive solutions (HCl, H 2 SO 4 , HNO 3 , NaOH, and KOH), using potentiodynamic polarization and chronoamperometry and X-ray diffraction and SEM observations. The results showed that the electrochemical stability and reproducibility of the composite electrodes in these diluted acids and alkalis were very good and had, in some extent, an electro-catalytic activity toward formation of hydrogen evolution and reduction of dissolved oxygen in aqueous solutions in comparison with a commercial graphite electrode. In addition, the pyrolyzed nano-carbon contents, size, and shape in the alumina matrix, have greatly effects on the electrochemical performances and electrode reactions in these solutions. It is found that the minimal residual carbon content of 0.62 wt.% in the matrix is enough to improve electrochemical performances and avoid to loss the ceramics physical properties at the same time. When the additional potential in all the tested electrolytes was at +1700 mV (vs. SCE), alumina particles at the electrode surface were not observed to dissolve into solution in this case, indicating the material being suitable for electrodes in aggressive solutions

  10. Electrochemically synthesized amorphous and crystalline nanowires: dissimilar nanomechanical behavior in comparison with homologous flat films

    Science.gov (United States)

    Zeeshan, M. A.; Esqué-de Los Ojos, D.; Castro-Hartmann, P.; Guerrero, M.; Nogués, J.; Suriñach, S.; Baró, M. D.; Nelson, B. J.; Pané, S.; Pellicer, E.; Sort, J.

    2016-01-01

    The effects of constrained sample dimensions on the mechanical behavior of crystalline materials have been extensively investigated. However, there is no clear understanding of these effects in nano-sized amorphous samples. Herein, nanoindentation together with finite element simulations are used to compare the properties of crystalline and glassy CoNi(Re)P electrodeposited nanowires (φ ~ 100 nm) with films (3 μm thick) of analogous composition and structure. The results reveal that amorphous nanowires exhibit a larger hardness, lower Young's modulus and higher plasticity index than glassy films. Conversely, the very large hardness and higher Young's modulus of crystalline nanowires are accompanied by a decrease in plasticity with respect to the homologous crystalline films. Remarkably, proper interpretation of the mechanical properties of the nanowires requires taking the curved geometry of the indented surface and sink-in effects into account. These findings are of high relevance for optimizing the performance of new, mechanically-robust, nanoscale materials for increasingly complex miniaturized devices.The effects of constrained sample dimensions on the mechanical behavior of crystalline materials have been extensively investigated. However, there is no clear understanding of these effects in nano-sized amorphous samples. Herein, nanoindentation together with finite element simulations are used to compare the properties of crystalline and glassy CoNi(Re)P electrodeposited nanowires (φ ~ 100 nm) with films (3 μm thick) of analogous composition and structure. The results reveal that amorphous nanowires exhibit a larger hardness, lower Young's modulus and higher plasticity index than glassy films. Conversely, the very large hardness and higher Young's modulus of crystalline nanowires are accompanied by a decrease in plasticity with respect to the homologous crystalline films. Remarkably, proper interpretation of the mechanical properties of the nanowires

  11. Investigations on Microstructure and Corrosion behavior of Superalloy 686 weldments by Electrochemical Corrosion Technique

    Science.gov (United States)

    Arulmurugan, B.; Manikandan, M.

    2018-02-01

    In the present study, microstructure and the corrosion behavior of Nickel based superalloy 686 and its weld joints has been investigated by synthetic sea water environment. The weldments were fabricated by Gas Tungsten Arc Welding (GTAW) and Pulsed Current Gas Tungsten Arc Welding (PCGTAW) techniques with autogenous mode and three different filler wires (ERNiCrMo-4, ERNiCrMo-10 and ERNiCrMo-14). Microstructure and Scanning electron microscope examination was carried out to evaluate the structural changes in the fusion zones of different weldments. Energy Dispersive X-ray Spectroscopy (EDS) analysis was carried out to evaluate the microsegregation of alloying elements in the different weld joints. Potentiodynamic polarization study was experimented on the base metal and weld joints in the synthetic sea water environment to evaluate the corrosion rate. Tafel’s interpolation technique was used to obtain the corrosion rate. The microstructure examination revealed that the fine equiaxed dendrites were observed in the pulsed current mode. EDS analysis shows the absence of microsegregation in the current pulsing technique. The corrosion rates of weldments are compared with the base metal. The results show that the fine microstructure with the absence of microsegregation in the PCGTA weldments shows improved corrosion resistance compared to the GTAW. Autogenous PCGTAW shows higher corrosion resistance irrespective of all weldments employed in the present study.

  12. Electrochemical behavior of meso-substituted iron porphyrins in alkaline aqueous media

    Science.gov (United States)

    Berezina, N. M.; Bazanov, M. I.; Maksimova, A. A.; Semeikin, A. S.

    2017-12-01

    The effect meso-substitution in iron porphyrin complexes has on their redox behavior in alkaline aqueous solutions is studied via cyclic voltammetry. The voltammetric features of the reduction of iron pyridylporphyrins suggest that the sites of electron transfer lie at the ligand, the metal ion, and the pyridyl moieties. The electron transfer reactions between the different forms of these compounds, including the oxygen reduction reaction they mediate, are outlined to show the sequence and potential ranges in which they occur in alkaline aqueous media. Under our experimental conditions, the iron porphyrins exist as μ-oxo dimmers whose activity for the electrocatalytic reduction of oxygen displays a considerable dependence on the nature of the substitutents and nitrogen isomerization (for pyridylporphyrins) and grows in the order (Fe( ms-Ph)4P)2O, (Fe[ ms-(Py-3)Ph3]P)2O, (Fe[ ms-(Py-4)4]P)2O, and (Fe[ ms-(Py-3)4]P)2O.

  13. Longitudinal Bidirectional Relations between Adolescents' Sympathy and Prosocial Behavior

    Science.gov (United States)

    Carlo, Gustavo; Padilla-Walker, Laura M.; Nielson, Matthew G.

    2015-01-01

    Despite the importance of understanding sympathy and prosocial behaviors, research on the development of these tendencies in adolescence remains relatively sparse. In the present study, we examined age trends and bidirectional longitudinal relations in sympathy and prosocial behaviors across early to middle adolescents. Participants were 500…

  14. Subjective Relational Experiences and Employee Innovative Behaviors in the Workplace

    Science.gov (United States)

    Vinarski-Peretz, Hedva; Binyamin, Galy; Carmeli, Abraham

    2011-01-01

    This paper presents two studies that explore the implications of subjective relational experiences (positive regard, mutuality and vitality) on employee engagement in innovative behaviors at work. Data collected at two points in time were used to test two mediation models that link subjective relational experiences and innovative behaviors. The…

  15. Effect of surface modification by nitrogen ion implantation on the electrochemical and cellular behaviors of super-elastic NiTi shape memory alloy.

    Science.gov (United States)

    Maleki-Ghaleh, H; Khalil-Allafi, J; Sadeghpour-Motlagh, M; Shakeri, M S; Masoudfar, S; Farrokhi, A; Beygi Khosrowshahi, Y; Nadernezhad, A; Siadati, M H; Javidi, M; Shakiba, M; Aghaie, E

    2014-12-01

    The aim of this investigation was to enhance the biological behavior of NiTi shape memory alloy while preserving its super-elastic behavior in order to facilitate its compatibility for application in human body. The surfaces of NiTi samples were bombarded by three different nitrogen doses. Small-angle X-ray diffraction was employed for evaluating the generated phases on the bombarded surfaces. The electrochemical behaviors of the bare and surface-modified NiTi samples were studied in simulated body fluid (SBF) using electrochemical impedance and potentio-dynamic polarization tests. Ni ion release during a 2-month period of service in the SBF environment was evaluated using atomic absorption spectrometry. The cellular behavior of nitrogen-modified samples was studied using fibroblast cells. Furthermore, the effect of surface modification on super-elasticity was investigated by tensile test. The results showed the improvement of both corrosion and biological behaviors of the modified NiTi samples. However, no significant change in the super-elasticity was observed. Samples modified at 1.4E18 ion cm(-2) showed the highest corrosion resistance and the lowest Ni ion release.

  16. Electrochemical behavior of platinum nanoparticles on a carbon xerogel support modified with a [(trifluoromethyl)-benzenesulfonyl]imide electrolyte.

    Science.gov (United States)

    Liu, Bing; Mei, Hua; DesMarteau, Darryl; Creager, Stephen E

    2014-12-11

    A monoprotic [(trifluoromethyl)benzenesulfonyl]imide (SI) superacid electrolyte was used to covalently modify a mesoporous carbon xerogel (CX) support via reaction of the corresponding trifluoromethyl aryl sulfonimide diazonium zwitterion with the carbon surface. Electrolyte attachment was demonstrated by elemental analysis, acid-base titration, and thermogravimetric analysis. The ion-exchange capacity of the fluoroalkyl-aryl-sulfonimide-grafted carbon xerogel (SI-CX) was ∼0.18 mequiv g(-1), as indicated by acid-base titration. Platinum nanoparticles were deposited onto the SI-grafted carbon xerogel samples by the impregnation and reduction method, and these materials were employed to fabricate polyelectrolyte membrane fuel-cell (PEMFC) electrodes by the decal transfer method. The SI-grafted carbon-xerogel-supported platinum (Pt/SI-CX) was characterized by X-ray diffraction and transmission electron microscopy to determine platinum nanoparticle size and distribution, and the findings are compared with CX-supported platinum catalyst without the grafted SI electrolyte (Pt/CX). Platinum nanoparticle sizes are consistently larger on Pt/SI-CX than on Pt/CX. The electrochemically active surface area (ESA) of platinum catalyst on the Pt/SI-CX and Pt/CX samples was measured with ex situ cyclic voltammetry (CV) using both hydrogen adsorption/desorption and carbon monoxide stripping methods and by in situ CV within membrane electrode assemblies (MEAs). The ESA values for Pt/SI-CX are consistently lower than those for Pt/CX. Some possible reasons for the behavior of samples with and without grafted SI layers and implications for the possible use of SI-grafted carbon layers in PEMFC devices are discussed.

  17. Properties and electrochemical behaviors of AuPt alloys prepared by direct-current electrodeposition for lithium air batteries

    International Nuclear Information System (INIS)

    Zhang, Jinqiu; Li, Da; Zhu, Yiming; Chen, Miaomiao; An, Maozhong; Yang, Peixia; Wang, Peng

    2015-01-01

    AuPt catalyst has a prospective application in a lithium air battery because of its bi-function on catalyzing Oxygen Reduction Reaction (ORR) and Oxygen Evolution Reaction (OER). Electrodeposition is an in-situ convenient technology for catalyst preparation without chemical residue. In an acid electrolyte, AuPt alloy catalysts were electrodeposited on carbon paper. The effect of main salt concentration, electrodeposition time and current density were studied by deposit micromorphology observation, structure analyses and composition testing. Catalytic abilities of AuPt alloys were measured by cyclic voltammetry (CV) in an ionic liquid of EMI-TFSI/Li-TFSI [1- Ethyl - 3- methylimidazolium–bis (trifluoromethanesulphonyl) imide/lithium–bis (trifluoromethanesulphonyl) imide]. The electrochemical behaviors of Au, Pt and AuPt deposits were also measured. An optimized direct-current electrodeposition process of getting high active AuPt catalyst is concluded, which is an aqueous solution containing 6.7∼10 mmol · L −1 HAuCl 4 , 10∼13.3 mmol · L −1 H 2 PtCl 6 and 0.5 mol · L −1 H 2 SO 4 as the electrolyte, current density of 20mA · cm −2 and electrodeposition time of 8∼34 s. The co-deposition of AuPt alloy is an irregular co-deposition controlled by diffusion, while gold atoms enter the platinum’s crystal lattice in the structure of AuPt alloy. The increase of the concentration of H 2 PtCl 6 in the electrolyte, the extension of the electrodeposition time or the raise of the current density can improve the content of Pt in the deposit. The clusters’ diameters of AuPt catalysts decrease to 150∼250 nm by adjusting current densities during electrodeposition

  18. On the behavior of reduced graphene oxide based electrodes coated with dispersed platinum by alternate current methods in the electrochemical degradation of reactive dyes.

    Science.gov (United States)

    Del Río, A I; García, C; Molina, J; Fernández, J; Bonastre, J; Cases, F

    2017-09-01

    The electrochemical behavior of different carbon-based electrodes with and without nanoparticles of platinum electrochemically dispersed on their surface has been studied. Among others, reduced graphene oxide based electrodes was used to determine the best conditions for the decolorization/degradation of the reactive dye C.I. Reactive Orange 4 in sulfuric medium. Firstly, the electrochemical behavior was evaluated by cyclic voltammetry. Secondly, different electrolyses were performed using two cell configurations: cell with anodic and cathodic compartments separated (divided configuration) and without any separation (undivided configuration). The best results were obtained when reduced graphene oxide based anodes were used. The degree of decolorization was monitored by spectroscopic methods and high performance liquid chromatography. It was found that all of them followed pseudo-first order kinetics. When reduced graphene oxide-based electrodes coated with dispersed platinum by alternate current methods electrodes were used, the lowest energy consumption and the higher decolorization kinetics rate were obtained. Scanning Electronic Microscopy was used to observe the morphological surface differences. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Electrochemical Behavior of Sn-9Zn- xTi Lead-Free Solders in Neutral 0.5M NaCl Solution

    Science.gov (United States)

    Wang, Zhenghong; Chen, Chuantong; Jiu, Jinting; Nagao, Shijo; Nogi, Masaya; Koga, Hirotaka; Zhang, Hao; Zhang, Gong; Suganuma, Katsuaki

    2018-05-01

    Electrochemical techniques were employed to study the electrochemical corrosion behavior of Sn-9Zn- xTi ( x = 0, 0.05, 0.1, 0.2 wt.%) lead-free solders in neutral 0.5M NaCl solution, aiming to figure out the effect of Ti content on the corrosion properties of Sn-9Zn, providing information for the composition design of Sn-Zn-based lead-free solders from the perspective of corrosion. EIS results reveal that Ti addition was involved in the corrosion product layer and changed electrochemical interface behavior from charge transfer control process to diffusion control process. The trace amount of Ti addition (0.05 wt.%) can refine the microstructure and improve the corrosion resistance of Sn-9Zn solder, evidenced by much lower corrosion current density ( i corr) and much higher total resistance ( R t). Excess Ti addition (over 0.1 wt.%) led to the formation of Ti-containing IMCs, which were confirmed as Sn3Ti2 and Sn5Ti6, deteriorating the corrosion resistance of Sn-9Zn- xTi solders. The main corrosion products were confirmed as Sn3O(OH)2Cl2 mixed with small amount of chlorine/oxide Sn compounds.

  20. Preparation, electrochemical behavior and electrocatalytic activity of chlorogenic acid multi-wall carbon nanotubes as a hydroxylamine sensor

    Energy Technology Data Exchange (ETDEWEB)

    Zare, Hamid R., E-mail: hrzare@yazduni.ac.ir; Nasirizadeh, Navid; Ajamain, Hamideh; Sahragard, Ali

    2011-07-20

    Electrochemical characteristics of an electrodeposited chlorogenic acid film on multi-wall carbon nanotubes glassy carbon electrode (CGA-MWCNT-GCE) and its role as a sensor for electrocatalytic oxidation of hydroxylamine are described. Cyclic voltammograms of the CGA-MWCNT-GCE indicate a pair of well-defined and nearly reversible redox couple with the surface confined characteristics at a wide pH range of 2.0-12.0. The charge transfer coefficient, {alpha}, and the charge transfer rate constant, k{sub s}, of CGA adsorbed on MWCNT were calculated 0.48 and 44 {+-} 2 s{sup -1} respectively. The CGA-MWCNT-GCE shows a dramatic increase in the peak current and/or a decrease in the overvoltage of hydroxylamine electrooxidation in comparison with that seen at a CGA modified GCE, MWCNT modified GCE and activated GCE. The kinetic parameters of electron transfer coefficient, {alpha}, the heterogeneous electron transfer rate constant, k', and exchange current, i{sub 0}, for oxidation of hydroxylamine at the modified electrode surface were determined using cyclic voltammetry. Four linear calibration ranges and high repeatability with relative standard deviation of 4.6%, for a series of four successive measurements in 17.7 {mu}M hydroxylamine, are obtained at the CGA-MWCNT-GCE using an amperometric method. Finally, the modified electrode was successfully used for determination of spiked hydroxylamine in two water samples.

  1. Preparation, electrochemical behavior and electrocatalytic activity of chlorogenic acid multi-wall carbon nanotubes as a hydroxylamine sensor

    International Nuclear Information System (INIS)

    Zare, Hamid R.; Nasirizadeh, Navid; Ajamain, Hamideh; Sahragard, Ali

    2011-01-01

    Electrochemical characteristics of an electrodeposited chlorogenic acid film on multi-wall carbon nanotubes glassy carbon electrode (CGA-MWCNT-GCE) and its role as a sensor for electrocatalytic oxidation of hydroxylamine are described. Cyclic voltammograms of the CGA-MWCNT-GCE indicate a pair of well-defined and nearly reversible redox couple with the surface confined characteristics at a wide pH range of 2.0-12.0. The charge transfer coefficient, α, and the charge transfer rate constant, k s , of CGA adsorbed on MWCNT were calculated 0.48 and 44 ± 2 s -1 respectively. The CGA-MWCNT-GCE shows a dramatic increase in the peak current and/or a decrease in the overvoltage of hydroxylamine electrooxidation in comparison with that seen at a CGA modified GCE, MWCNT modified GCE and activated GCE. The kinetic parameters of electron transfer coefficient, α, the heterogeneous electron transfer rate constant, k', and exchange current, i 0 , for oxidation of hydroxylamine at the modified electrode surface were determined using cyclic voltammetry. Four linear calibration ranges and high repeatability with relative standard deviation of 4.6%, for a series of four successive measurements in 17.7 μM hydroxylamine, are obtained at the CGA-MWCNT-GCE using an amperometric method. Finally, the modified electrode was successfully used for determination of spiked hydroxylamine in two water samples.

  2. Effect of rigidity of porous structure on electrochemical behavior of pristine Li4Ti5O12 microspheres

    International Nuclear Information System (INIS)

    Jia, Zhenyong; Zhou, Qun; Li, Xiaowei; Fu, Yu; Ming, Hai; Zheng, Junwei

    2015-01-01

    Highlights: • Rigid porous framework of Li 4 Ti 5 O 12 microspheres can be fabricated by mutual molten growth of primary particles. • Well-confined nanosized tortuous channels are formed inside Li 4 Ti 5 O 12 microspheres. • Li 4 Ti 5 O 12 microspheres with rigid porous structures exhibit greatly enhanced electrochemical performance. - Abstract: Highly controllable porous architecture is desirable to tailor the physical and chemical properties of functional materials in advanced lithium ion batteries. Here, porous microspheres of spinel lithium titanate (Li 4 Ti 5 O 12 ), a promising alternative anode material for lithium ion batteries, are fabricated by mutual molten growth method in a controllable manner. The key role of the rigidity of the porous structure on the performance of the electrode materials in lithium ion batteries is demonstrated. Rigid framework of the materials is formed by second growth of the primary particles that fused together to generate an interconnected nanopore system inside the spheres, leading to better electrolyte diffusion and lower interparticle contact resistance, relative to the non-porous counterpart. The pristine Li 4 Ti 5 O 12 microspheres with uniform pore distribution and continuous framework exhibit high tap density, remarkable reversible capacity and rate capability, as well as excellent cycling stability. The present method is scalable and may provide a new approach to fabricate other candidate electrode materials for applications that require both high power and high volumetric energy density

  3. The effects to the structure and electrochemical behavior of zinc phosphate conversion coatings with ethanolamine on magnesium alloy AZ91D

    International Nuclear Information System (INIS)

    Li Qing; Xu Shuqiang; Hu Junying; Zhang Shiyan; Zhong Xiankang; Yang Xiaokui

    2010-01-01

    This paper discussed a zinc phosphate conversion coating formed on magnesium alloy AZ91D from the phosphating bath with varying amounts of ethanolamine (MEA). The effects of MEA on the form, structure, phase composition and electrochemical behavior of the phosphate coatings were examined using an scanning electron microscopy (SEM), X-ray diffraction (XRD) potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) measurements. Interpretations of the electrical elements of the equivalent circuit were obtained from the SEM structure of the coatings, assumed to be formed of two layers: an outer porous crystal layer and an inner flat amorphous layer. The result showed that adding MEA refined the microstructure of the crystal layer and that the phosphate coating, derived at the optimal content of 1.2 g/L, with the most uniform and compact outer crystal layer provided the best corrosion protection.

  4. Effect of calcium on the electrochemical behavior of lithium anode in LiOH aqueous solution used for lithium–water battery

    International Nuclear Information System (INIS)

    Zhang Ziyan; Chen Kanghua; Ni Erfu

    2012-01-01

    The effect of minor addition of calcium to lithium anode on the electrochemical behavior of lithium anode in 4 M LiOH at 30 °C temperature is investigated by hydrogen collection, polarization curves and electrochemical impedance spectroscopy. The results show that the hydrogen evolution rate is marginally reduced with increasing calcium content. Addition of calcium to lithium mainly inhibits the anodic process. Minor addition of calcium to lithium slightly reduced the discharge current of lithium anode. Minor addition of calcium to lithium anode marginally enhances the hydrogen inhibition of lithium by the formation of calcium hydride combined with LiOH and LiOH·H 2 O formed on the anode surface.

  5. Studies on the Electrochemical Behavior of Thiazolidine and Its Applications Using a Flow–Through Chronoamperometric Sensor Based on a Gold Electrode

    Directory of Open Access Journals (Sweden)

    Lai-Hao Wang

    2011-09-01

    Full Text Available The electrochemical behaviors of thiazolidine (tetrahydrothiazole on gold and platinum electrodes were investigated in a Britton-Robinson buffer (pH 2.77–11.61, acetate buffer (pH 4.31, phosphate buffer solutions (pH 2.11 and 6.38 and methanol or acetonitrile containing various supporting electrolytes. Detection was based on a gold wire electrochemical signal obtained with a supporting electrolyte containing 20% methanol-1.0 mM of phosphate buffer (pH 6.87, potassium dihydrogen phosphate and dipotassium hydrogen phosphate as the mobile phase. Comparison with results obtained with a commercial amperometric detector shows good agreement. Using the chronoamperometric sensor with the current at a constant potential, and measurements with suitable experimental parameters, a linear concentration from 0.05 to 16 mg L−1 was found. The limit of quantification (LOQ of the method for thiazolidine was found to be 1 ng.

  6. Effect of pH Value on the Electrochemical and Stress Corrosion Cracking Behavior of X70 Pipeline Steel in the Dilute Bicarbonate Solutions

    Science.gov (United States)

    Cui, Z. Y.; Liu, Z. Y.; Wang, L. W.; Ma, H. C.; Du, C. W.; Li, X. G.; Wang, X.

    2015-11-01

    In this work, effects of pH value on the electrochemical and stress corrosion cracking (SCC) behavior of X70 pipeline steel in the dilute bicarbonate solutions were investigated using electrochemical measurements, slow strain rate tensile tests and surface analysis techniques. Decrease of the solution pH from 6.8 to 6.0 promotes the anodic dissolution and cathodic reduction simultaneously. Further decrease of the pH value mainly accelerates the cathodic reduction of X70 pipeline steel. As a result, when the solution pH decreases form 6.8 to 5.5, SCC susceptibility decreases because of the enhancement of the anodic dissolution. When the solution pH decreases from 5.5 to 4.0, SCC susceptibility increases gradually because of the acceleration of cathodic reactions.

  7. Effect of Processing Conditions of 75Li2S-25P2S5 Solid Electrolyte on its DC Electrochemical Behavior

    International Nuclear Information System (INIS)

    Garcia-Mendez, Regina; Mizuno, Fuminori; Zhang, Ruigang; Arthur, Timothy S.; Sakamoto, Jeff

    2017-01-01

    Highlights: • The highly conductive thio-LiSICON III analog phase formed when hot pressing LPS between 170–250 °C. • The low conductivity Li 3 PS 4 phase formed when hot pressing LPS at 300 °C. • Obtaining LPS glass-ceramic through hot pressing increased the rate at which current can be passed through the cell before short circuit is observed. • The critical current density is affected by the LPS phase present and adhesion between particles. - Abstract: The effect of processing conditions of the 75Li 2 S-25P 2 S 5 (LPS) on the Li/LPS DC electrochemical stability was investigated. LPS was densified by compacting at room temperature, and hot pressed between 130–300 °C, 47 MPa. The relative density (80% for all samples) was not affected by the hot pressing temperature, which was likely due to insufficient bulk diffusion (at the pressure used within the temperature range selected) to promote densification. The highly conductive meta-stable crystalline phase (thio-LiSICON III analog) precipitated from the mother glass when hot pressing between 170 − 250 °C and the low conductivity Li 3 PS 4 phase formed when hot pressing at 300 °C. The Li/LPS DC electrochemical stability was characterized as a function of current density between 0.01–1.0 mA· cm −2 . Two phenomena were observed; first, as the current density increased, deviation from Ohmic behavior was observed, manifested in an increase in output potential difference. Second, as the current density was further increased, a drop in cell potential was observed followed by an output potential difference instability; likely consistent with short-circuiting caused by Li metal propagation. The highest critical current density, at which short circuit occurs, resulted when hot pressing at 170 °C, reaching 1.0 mA· cm −2 . In general, obtaining LPS glass-ceramic through hot pressing increased the rate at which current can be passed through the cell. It is believed that further atomic

  8. Investigation into electrochemical behavior of molybdenum VM-1 alloy at high current density

    Energy Technology Data Exchange (ETDEWEB)

    Tatarinova, O M; Amirkhanova, N A; Akhmadiev, A G

    1975-01-01

    The effect of the composition and concentration of electrolyte on the workability of the molybdenum VM-1 alloy has been studied and a number of anions has been determined relative to their activation capacity. The best workability of the alloy is achieved in a 15% NaOH solution and a composite electrolyte 15% NaNO/sub 3/+5%NaOH. It is shown that in polarization of the VM-1 alloy both in alkali- and salt solutions a film of oxides of different valence molybdenum is formed: Mo/sub 2/O/sub 3/, Mo/sub 4/O/sub 11/, Mo/sub 9/O/sub 26/, MoO/sub 3/, but molybdenum gets dissolved only in a hexavalent form, its content in a solution being in conformity with the polarizing current densities. Using a temperature-kinetic technique it has been found that the concentrational polarization is the limiting stage in the reaction of molybdenum and VM-1 alloy anodic dissolution in 15% NaNO/sub 3/ solution and in the composite electrolyte 15%NaNO/sub 3/+5%NaOH.

  9. The electrochemical behavior of Co(TPTZ)2 complex on different carbon based electrodes modified with TiO2 nanoparticles

    International Nuclear Information System (INIS)

    Ortaboy, Sinem; Atun, Gülten

    2015-01-01

    Electrochemical behavior of cobalt (II) complex with the N-donor ligand 2,2′-bipyridyl-1,3,5-tripyridyl-s-triazine (TPTZ) was investigated to elucidate the electron-proton transfer mechanisms. The electrochemical response of the complex was studied using square-wave voltammetry (SWV) and electrochemical impedance spectroscopy (EIS) techniques. A conventional three-electrode system, consisting of glassy carbon (GCE), TiO 2 modified glassy carbon (T/GCE), carbon paste (CPE) and TiO 2 modified carbon paste (T/CPE) working electrodes were employed. The ligand/metal ratio and stability constant of the complex as well as the mechanisms of the electrode processes were elucidated by examining the effects of pH, ligand concentration and frequency on the voltammograms. The EIS results indicated that the samples modified with TiO 2 had the higher charge transfer resistance than that of the bare electrodes and also suggested that the electroactivity of the electrode surfaces increased in the following order, T/CPE > CPE > T/GCE > GCE. The surface morphology of the working electrodes was also characterized by atomic force microscopy (AFM). The values of surface roughness parameters were found to be consistent with the results obtained by EIS experiments. - Graphical abstract: Schematic illustration of the experimental process. - Highlights: • Electrochemical behavior of Co(TPTZ) 2 complex studied by SWV and EIS techniques. • GCE, CPE T/GCE and T/CPE were used as working electrodes for comparative studies. • The surface morphologies of the electrodes were characterized by AFM. • Mechanisms were proposed from the effects of pH, ligand concentration and frequency. • EIS and morphologic relationships of the surfaces were established successfully

  10. The electrochemical behavior of Co(TPTZ){sub 2} complex on different carbon based electrodes modified with TiO{sub 2} nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Ortaboy, Sinem, E-mail: ortaboy@istanbul.edu.tr; Atun, Gülten, E-mail: gatun@istanbul.edu.tr

    2015-04-15

    Electrochemical behavior of cobalt (II) complex with the N-donor ligand 2,2′-bipyridyl-1,3,5-tripyridyl-s-triazine (TPTZ) was investigated to elucidate the electron-proton transfer mechanisms. The electrochemical response of the complex was studied using square-wave voltammetry (SWV) and electrochemical impedance spectroscopy (EIS) techniques. A conventional three-electrode system, consisting of glassy carbon (GCE), TiO{sub 2} modified glassy carbon (T/GCE), carbon paste (CPE) and TiO{sub 2} modified carbon paste (T/CPE) working electrodes were employed. The ligand/metal ratio and stability constant of the complex as well as the mechanisms of the electrode processes were elucidated by examining the effects of pH, ligand concentration and frequency on the voltammograms. The EIS results indicated that the samples modified with TiO{sub 2} had the higher charge transfer resistance than that of the bare electrodes and also suggested that the electroactivity of the electrode surfaces increased in the following order, T/CPE > CPE > T/GCE > GCE. The surface morphology of the working electrodes was also characterized by atomic force microscopy (AFM). The values of surface roughness parameters were found to be consistent with the results obtained by EIS experiments. - Graphical abstract: Schematic illustration of the experimental process. - Highlights: • Electrochemical behavior of Co(TPTZ){sub 2} complex studied by SWV and EIS techniques. • GCE, CPE T/GCE and T/CPE were used as working electrodes for comparative studies. • The surface morphologies of the electrodes were characterized by AFM. • Mechanisms were proposed from the effects of pH, ligand concentration and frequency. • EIS and morphologic relationships of the surfaces were established successfully.

  11. Fabrication and metallization of 3D electrospun nanofiberous architecture with gold and silver coating for applications related to electrochemical supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Park, Keon Young [University of Pennsylvania, 3451 Walnut Street, Philadelphia, PA 19104 (United States); Ramaraj, B. [Research and Development Department, Central Institute of Plastics Engineering and Technology (CIPET), 630, Phase IV, GIDC, Vatva, Ahmedabad 382445 (India); Choi, Won Suk [Department of Chemistry, Hannam University, 461-6 Jeon min-dong, Yuseoung-gu, Daejeon 305-811 (Korea, Republic of); Yoon, Kuk Ro, E-mail: kryoon@hannam.ac.kr [Department of Chemistry, Hannam University, 461-6 Jeon min-dong, Yuseoung-gu, Daejeon 305-811 (Korea, Republic of)

    2013-11-01

    We have engineered a metallic architecture with high surface area and ultralow density for applications related to electrochemical supercapacitors. This is achieved first by design and fabrication of new annular collector template for electrospinning process, then the extrusion of polystyrene (PS) nanofiber through the fabricated annulus collector template followed by electroless plating of nanofiber assembly with gold and silver. The resultant three dimensional structures were characterized by optical microscopy (OM), Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM). The OM images suggest that the fabrication process causes the electrospun fibers to be hinged to one another, maximizing contact junctions enhancing mechanical stability. The coated structure has a superior surface area, is robust, and is freestanding – making it an attractive architectural design for an electrode. The SEM images show interlocking of nanofibers to one another, further indicating the potential application for this system as a high surface area, low density charge collector ideal for nanostructured growths. - Graphical abstract: A new annular collector template was designed and fabricated to create a 3D electrospun nanofiber assembly. This ultralight 3D architecture with high surface was electroless plated with silver and gold to assess its suitability for applications related to electrochemical supercapacitors. This structure is highly conductive leading us to believe that this product can be utilized as an alternate electrode charge collector. - Highlights: • A metallic architecture with high surface area and ultralow density was fabricated. • A new annular collector template for electrospinning was designed and fabricated. • Electrospun PS nanofibers with 3D structure were coated with silver and gold. • The coated structure is

  12. Fabrication and metallization of 3D electrospun nanofiberous architecture with gold and silver coating for applications related to electrochemical supercapacitors

    International Nuclear Information System (INIS)

    Park, Keon Young; Ramaraj, B.; Choi, Won Suk; Yoon, Kuk Ro

    2013-01-01

    We have engineered a metallic architecture with high surface area and ultralow density for applications related to electrochemical supercapacitors. This is achieved first by design and fabrication of new annular collector template for electrospinning process, then the extrusion of polystyrene (PS) nanofiber through the fabricated annulus collector template followed by electroless plating of nanofiber assembly with gold and silver. The resultant three dimensional structures were characterized by optical microscopy (OM), Fourier-transform infrared (FTIR) spectroscopy, thermogravimetric analysis (TGA), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD) analysis and scanning electron microscopy (SEM). The OM images suggest that the fabrication process causes the electrospun fibers to be hinged to one another, maximizing contact junctions enhancing mechanical stability. The coated structure has a superior surface area, is robust, and is freestanding – making it an attractive architectural design for an electrode. The SEM images show interlocking of nanofibers to one another, further indicating the potential application for this system as a high surface area, low density charge collector ideal for nanostructured growths. - Graphical abstract: A new annular collector template was designed and fabricated to create a 3D electrospun nanofiber assembly. This ultralight 3D architecture with high surface was electroless plated with silver and gold to assess its suitability for applications related to electrochemical supercapacitors. This structure is highly conductive leading us to believe that this product can be utilized as an alternate electrode charge collector. - Highlights: • A metallic architecture with high surface area and ultralow density was fabricated. • A new annular collector template for electrospinning was designed and fabricated. • Electrospun PS nanofibers with 3D structure were coated with silver and gold. • The coated structure is

  13. Investigating Culture-related Aspects of Behavior for Virtual Characters

    DEFF Research Database (Denmark)

    Endrass, Birgit; André, Elisabeth; Rehm, Matthias

    2013-01-01

    In this paper, culture-related behaviors are investigated on several channels of communication for virtual characters. Prototypical behaviors were formalized in computational models based on a literature review as well as a corpus analysis, exemplifying the German and Japanese cultures. Therefore...

  14. Substantive and relational effectiveness of organizational conflict behavior

    NARCIS (Netherlands)

    Euwema, M C; Van de Vliert, E; Bakker, A B

    2003-01-01

    In this observation study the theory of conglomerated conflict behavior is tested. The impact of seven conflict behaviors on substantive and relational conflict outcomes is examined through multiple independent observations of 103 Dutch nurse managers handling a standardized conflict. Results show

  15. Electrochemical thermodynamic measurement system

    Science.gov (United States)

    Reynier, Yvan [Meylan, FR; Yazami, Rachid [Los Angeles, CA; Fultz, Brent T [Pasadena, CA

    2009-09-29

    The present invention provides systems and methods for accurately characterizing thermodynamic and materials properties of electrodes and electrochemical energy storage and conversion systems. Systems and methods of the present invention are configured for simultaneously collecting a suite of measurements characterizing a plurality of interconnected electrochemical and thermodynamic parameters relating to the electrode reaction state of advancement, voltage and temperature. Enhanced sensitivity provided by the present methods and systems combined with measurement conditions that reflect thermodynamically stabilized electrode conditions allow very accurate measurement of thermodynamic parameters, including state functions such as the Gibbs free energy, enthalpy and entropy of electrode/electrochemical cell reactions, that enable prediction of important performance attributes of electrode materials and electrochemical systems, such as the energy, power density, current rate and the cycle life of an electrochemical cell.

  16. College students' behavioral reactions upon witnessing relational peer aggression.

    Science.gov (United States)

    You, Ji-In; Bellmore, Amy

    2014-01-01

    With a sample of 228 college students (82.5% females) from the Midwestern United States, individual factors that contribute to emerging adults' behavioral responses when witnessing relational aggression among their peers were explored. The experience of witnessing relational aggression was found to be systematically associated with college students' behavioral responses to relational aggression through two social cognitive processes: normative beliefs about relational aggression and susceptibility to peer influence. The experience of witnessing relational aggression was associated with defending behavior through normative beliefs about relational aggression and both assisting and reinforcing behavior through normative beliefs about relational aggression and susceptibility to peer influence. The experience of witnessing relational aggression was also associated with onlooking behavior through normative beliefs about relational aggression. The findings indicate that exposure to relational aggression as a witness may influence witness responses because of the way such exposure may shape specific social cognitions. The potential for using the study findings for promoting effective witness interventions among college students is discussed. © 2014 Wiley Periodicals, Inc.

  17. Electrochemical energy storage behavior of Sn/SnO2 double phase nanocomposite anodes produced on the multiwalled carbon nanotube buckypapers for lithium-ion batteries

    Science.gov (United States)

    Alaf, Mirac; Akbulut, Hatem

    2014-02-01

    Recent development of electrode materials for Li-ion batteries is driven mainly by hybrid nanocomposite structures consisting of Li storage compounds and CNTs. In this study, tin/tinoxide (Sn/SnO2) films and tin/tinoxide/multi walled carbon nanotube (Sn/SnO2/MWCNT) nanocomposites are produced by a two steps process; thermal evaporation and subsequent plasma oxidation as anode materials for Li-ion batteries. The physical, structural, and electrochemical behaviors of the nanocomposite electrodes containing MWCNTs are discussed. The ratio between metallic tin (Sn) and tinoxide (SnO2) is controlled with plasma oxidation time and effects of the ratio are investigated on the structural and electrochemical properties. The greatly enhanced electrochemical performance is mainly due to the morphological stability and reduced diffusion resistance, which are induced by MWCNT core and deposited Sn/SnO2 double phase shell. The outstanding long-term cycling stability is a result of the two layers Sn and SnO2 phases on MWCNTs. The nanoscale Sn/SnO2/MWCNT network provides good electrical conductivity, and the creation of open spaces that buffer a large volume change during the Li-alloying/de-alloying reaction.

  18. The Electrochemical Behavior of Carbon Fiber Microelectrodes Modified with Carbon Nanotubes Using a Two-Step Electroless Plating/Chemical Vapor Deposition Process

    Directory of Open Access Journals (Sweden)

    Longsheng Lu

    2017-03-01

    Full Text Available Carbon fiber microelectrode (CFME has been extensively applied in the biosensor and chemical sensor domains. In order to improve the electrochemical activity and sensitivity of the CFME, a new CFME modified with carbon nanotubes (CNTs, denoted as CNTs/CFME, was fabricated and investigated. First, carbon fiber (CF monofilaments grafted with CNTs (simplified as CNTs/CFs were fabricated in two key steps: (i nickel electroless plating, followed by (ii chemical vapor deposition (CVD. Second, a single CNTs/CF monofilament was selected and encapsulated into a CNTs/CFME with a simple packaging method. The morphologies of as-prepared CNTs/CFs were characterized by scanning electron microscopy. The electrochemical properties of CNTs/CFMEs were measured in potassium ferrocyanide solution (K4Fe(CN6, by using a cyclic voltammetry (CV and a chronoamperometry method. Compared with a bare CFME, a CNTs/CFME showed better CV curves with a higher distinguishable redox peak and response current; the higher the CNT content was, the better the CV curves were. Because the as-grown CNTs significantly enhanced the effective electrode area of CNTs/CFME, the contact area between the electrode and reactant was enlarged, further increasing the electrocatalytic active site density. Furthermore, the modified microelectrode displayed almost the same electrochemical behavior after 104 days, exhibiting remarkable stability and outstanding reproducibility.

  19. Electrochemical and wear behavior of niobium-vanadium carbide coatings produced on AISI H13 tool steel through thermo-reactive deposition/diffusion

    International Nuclear Information System (INIS)

    Castillejo Nieto, Fabio Enrique; Olaya Flores, Jhon Jairo; Alfonso Orjuela, Jose Edgar

    2016-01-01

    We deposited of niobium-vanadium carbide coatings on tool steel AISI H13 using the thermo-reactive substrates deposition/diffusion (TRD) technique. The carbides were obtained using salt baths composed of molten borax, ferroniobium, vanadium and aluminum, by heating this mixture at 1020°C for 4 hours. The coatings were characterized morphologically via electron microscopy scanning (SEM), the chemical surface composition was determined through X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectroscopy (EDX); the crystal structure was analyzed using x-ray diffraction (XRD), the mechanical properties of the coatings were evaluated using nano-indentation, The tribological properties of the coatings obtained were determined using a Pin-on-disk tribometer and the electrochemical behavior was studied through potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS). The results showed that the hardness of the coated steel increased four times with respect to uncoated steel, and the electrochemical test established that the corrosion current is lower by one order of magnitude for coated steel

  20. Electrochemical corrosion behavior and elasticity properties of Ti-6Al-xFe alloys for biomedical applications.

    Science.gov (United States)

    Lu, Jinwen; Zhao, Yongqing; Niu, Hongzhi; Zhang, Yusheng; Du, Yuzhou; Zhang, Wei; Huo, Wangtu

    2016-05-01

    The present study is to investigate the microstructural characteristics, electrochemical corrosion behavior and elasticity properties of Ti-6Al-xFe alloys with Fe addition for biomedical application, and Ti-6Al-4V alloy with two-phase (α+β) microstructure is also studied as a comparison. Microstructural characterization reveals that the phase and crystal structure are sensitive to the Fe content. Ti-6Al alloy displays feather-like hexagonal α phase, and Ti-6Al-1Fe exhibits coarse lath structure of hexagonal α phase and a small amount of β phase. Ti-6Al-2Fe and Ti-6Al-4Fe alloys are dominated by elongated, equiaxed α phase and retained β phase, but the size of α phase particle in Ti-6Al-4Fe alloy is much smaller than that in Ti-6Al-2Fe alloy. The corrosion resistance of these alloys is determined in SBF solution at 37 °C. It is found that the alloys spontaneously form a passive oxide film on their surface after immersion for 500 s, and then they are stable for polarizations up to 0 VSCE. In comparison with Ti-6Al and Ti-6Al-4V alloys, Ti-6Al-xFe alloys exhibit better corrosion resistance with lower anodic current densities, larger polarization resistances and higher open-circuit potentials. The passive layers show stable characteristics, and the wide frequency ranges displaying capacitive characteristics occur for high iron contents. Elasticity experiments are performed to evaluate the elasticity property at room temperature. Ti-6Al-4Fe alloy has the lowest Young's modulus (112 GPa) and exhibits the highest strength/modulus ratios as large as 8.6, which is similar to that of c.p. Ti (8.5). These characteristics of Ti-6Al-xFe alloys form the basis of a great potential to be used as biomedical implantation materials. Copyright © 2016 Elsevier B.V. All rights reserved.

  1. Electrochemical analyses of diffusion behaviors and nucleation mechanisms for neodymium complexes in [DEME][TFSA] ionic liquid

    International Nuclear Information System (INIS)

    MATSUMIYA, Masahiko; ISHII, Mai; KAZAMA, Ryo; KAWAKAMI, Satoshi

    2014-01-01

    Highlights: • The cathodic reaction; Nd(III) + 3e − → Nd(0) was observed at −3.30 V in [DEME][TFSA]. • The diffusion coefficient of Nd(III) in [DEME][TFSA] was evaluated from semi-integral analysis. • The nucleation mechanism of Nd nuclei was altered from instantaneous to progressive nucleation. • The number density of Nd nuclei was increased as the overpotential was increased. • The electrodeposits from [DEME][TFSA] were identified Nd metal and oxide mixtures by XPS. - ABSTRACT: The electrochemical and nucleation behavior of Nd(III) in the ammonium-based ionic liquid (IL), N,N-diethyl-N-methyl-N-(2-methoxyethyl) ammonium bis(trifluoromethyl-sulfonyl) amide, [DEME] [TFSA], were investigated in this study. The cathodic reaction of Nd(III) [Nd(III) + 3e − → Nd(0)] was observed at −3.30 V vs. Ag/Ag(I) using cyclic voltammetry at 353 K. The diffusion coefficient of Nd(III) was estimated to be 1.35 ± 0.10 × 10 −13 m 2 s −1 at 353 K using semi-integral and semi-differential analyses. The initial process of Nd electrodeposition was also evaluated by chronoamperometry, indicating that the initial nucleation and growth of Nd on the Pt electrode occurred via instantaneous nucleation at −3.40 V. As the applied potential became more negative, the mechanism changed from instantaneous to progressive nucleation. The number density of Nd nuclei in the initial stage of nucleation decreased as the overpotential increased. Furthermore, the electrodeposition of Nd was carried out under the conditions of −3.40 V and −3.60 V at 353 K. SEM observations of the electrodeposits were consistent with the series of results obtained by chronoamperometry. The electrodeposits consisted mainly of Nd metal and oxide mixtures, whereas bonding with the light elements (C, F, and S) of the IL was suppressed, as demonstrated by EDX and XPS. The results suggested that sufficient dehydration and control of the water content of the electrolyte are important factors

  2. Electrochemical attosyringe.

    Science.gov (United States)

    Laforge, François O; Carpino, James; Rotenberg, Susan A; Mirkin, Michael V

    2007-07-17

    The ability to manipulate ultrasmall volumes of liquids is essential in such diverse fields as cell biology, microfluidics, capillary chromatography, and nanolithography. In cell biology, it is often necessary to inject material of high molecular weight (e.g., DNA, proteins) into living cells because their membranes are impermeable to such molecules. All techniques currently used for microinjection are plagued by two common problems: the relatively large injector size and volume of injected fluid, and poor control of the amount of injected material. Here we demonstrate the possibility of electrochemical control of the fluid motion that allows one to sample and dispense attoliter-to-picoliter (10(-18) to 10(-12) liter) volumes of either aqueous or nonaqueous solutions. By changing the voltage applied across the liquid/liquid interface, one can produce a sufficient force to draw solution inside a nanopipette and then inject it into an immobilized biological cell. A high success rate was achieved in injections of fluorescent dyes into cultured human breast cells. The injection of femtoliter-range volumes can be monitored by video microscopy, and current/resistance-based approaches can be used to control injections from very small pipettes. Other potential applications of the electrochemical syringe include fluid dispensing in nanolithography and pumping in microfluidic systems.

  3. Electrochemical Behavior of TiO(x)C(y) as Catalyst Support for Direct Ethanol Fuel Cells at Intermediate Temperature: From Planar Systems to Powders.

    Science.gov (United States)

    Calvillo, Laura; García, Gonzalo; Paduano, Andrea; Guillen-Villafuerte, Olmedo; Valero-Vidal, Carlos; Vittadini, Andrea; Bellini, Marco; Lavacchi, Alessandro; Agnoli, Stefano; Martucci, Alessandro; Kunze-Liebhäuser, Julia; Pastor, Elena; Granozzi, Gaetano

    2016-01-13

    To achieve complete oxidation of ethanol (EOR) to CO2, higher operating temperatures (often called intermediate-T, 150-200 °C) and appropriate catalysts are required. We examine here titanium oxycarbide (hereafter TiOxCy) as a possible alternative to standard carbon-based supports to enhance the stability of the catalyst/support assembly at intermediate-T. To test this material as electrocatalyst support, a systematic study of its behavior under electrochemical conditions was carried out. To have a clear description of the chemical changes of TiOxCy induced by electrochemical polarization of the material, a special setup that allows the combination of X-ray photoelectron spectroscopy and electrochemical measurements was used. Subsequently, an electrochemical study was carried out on TiOxCy powders, both at room temperature and at 150 °C. The present study has revealed that TiOxCy is a sufficiently conductive material whose surface is passivated by a TiO2 film under working conditions, which prevents the full oxidation of the TiOxCy and can thus be considered a stable electrode material for EOR working conditions. This result has also been confirmed through density functional theory (DFT) calculations on a simplified model system. Furthermore, it has been experimentally observed that ethanol molecules adsorb on the TiOxCy surface, inhibiting its oxidation. This result has been confirmed by using in situ Fourier transform infrared spectroscopy (FTIRS). The adsorption of ethanol is expected to favor the EOR in the presence of suitable catalyst nanoparticles supported on TiOxCy.

  4. Health-related behaviors and technology usage among college students.

    Science.gov (United States)

    Melton, Bridget F; Bigham, Lauren E; Bland, Helen W; Bird, Matthew; Fairman, Ciaran

    2014-07-01

    To examine associations between technology usage and specific health factors among college students. The research employed was a quantitative, descriptive, cross-sectional design; undergraduate students enrolled in spring 2012 general health education courses were recruited to participate. To explore college students' specific technology usage and health-related behaviors, a 28-item questionnaire was utilized. Statistical significant differences of technology usage were found between 3 of the 4 health-related behaviors under study (BMI, sleep, and nutrition) (p technology usage continues to evolve within the college student population, health professionals need to understand its implications on health behaviors.

  5. Study for electrochemical behavior of uranium oxide in a molten LiCl-Li2O system

    International Nuclear Information System (INIS)

    Park, Sung Bin; Park, Byung Heung; Seo, Chung Seok; Jung, Ki Jung; Park, Seong Won

    2005-01-01

    Interest in the electrolytic reduction of uranium oxide is increasing in the treatment of spent fuel oxides. With complicated and expensive procedures many reactive metals can be prepared in a pure metal form, the electrochemical reduction of a metal oxide has been recently proposed in metallurgy. The electrochemical reduction process is simple and rapid when compared to the conventional processes. The process can reduce the production costs and be applicable to a wide range of metal oxides. Chen et al. proposed the direct electrochemical reduction of titanium dioxide to titanium in a molten calcium chloride. Argonne National Laboratory (ANL) has reported the experimental results of an electrochemical reduction of the uranium oxide fuel in a bench-scale apparatus with a cyclic voltammetry, and has designed high-capacity reduction (HCR) cells and conducted three kg-scale UO 2 reduction runs. Gourishankar et al. classified the mechanisms of the electrolytic reduction of the metal oxides in a LiCl-Li 2 O molten salt system into two types; the simultaneous reduction and the direct electrochemical reduction. The uranium oxide in LiCl-Li 2 O molten salt was converted to uranium metal according to two mechanisms. Korea Atomic Energy Research Institute (KAERI) has developed the Advanced Spent Fuel Conditioning Process (ACP) to be an innovative technology in handling the PWR spent fuel. As part of ACP, the electrolytic reduction process (ER process) is the electrochemical reduction process of uranium oxide to uranium metal in molten salt. The ER process has advantages in a technical stability, an economic potential and a good proliferation resistance. KAERI has reported on the good experimental results of an electrochemical reduction of the uranium oxide in a 20 kg HM/batch lab-scale. In this work, cyclic voltammograms for a LiCl-3 wt% Li 2 O system and an U 3 O 8 -LiCl-3 wt% Li 2 O system with the integrated cathode assembly have been obtained. From the cyclic

  6. Some current dimensions of the behavioral economics of health-related behavior change.

    Science.gov (United States)

    Bickel, Warren K; Moody, Lara; Higgins, Stephen T

    2016-11-01

    Health-related behaviors such as tobacco, alcohol and other substance use, poor diet and physical inactivity, and risky sexual practices are important targets for research and intervention. Health-related behaviors are especially pertinent targets in the United States, which lags behind most other developed nations on common markers of population health. In this essay we examine the application of behavioral economics, a scientific discipline that represents the intersection of economics and psychology, to the study and promotion of health-related behavior change. More specifically, we review what we consider to be some core dimensions of this discipline when applied to the study health-related behavior change. Behavioral economics (1) provides novel conceptual systems to inform scientific understanding of health behaviors, (2) translates scientific understanding into practical and effective behavior-change interventions, (3) leverages varied aspects of behavior change beyond increases or decreases in frequency, (4) recognizes and exploits trans-disease processes and interventions, and (5) leverages technology in efforts to maximize efficacy, cost effectiveness, and reach. These dimensions are overviewed and their implications for the future of the field discussed. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. [Health and health-related behaviors according to sexual attraction and behavior].

    Science.gov (United States)

    Pérez, Glòria; Martí-Pastor, Marc; Gotsens, Mercè; Bartoll, Xavier; Diez, Elia; Borrell, Carme

    2015-01-01

    to Describe perceived health, mental health and certain health-related behaviors according to sexual attraction and behavior in the population residing in Barcelona in 2011. Perceived health, mental health, chronic conditions and health-related behaviors were analyzed in 2675 people aged 15 to 64 years. The Barcelona Health Survey for 2011 was used, which included questions on sexual attraction and behavior. Multivariate robust Poisson regression models were fitted to obtain adjusted prevalence ratios. People feeling same-sex attraction reported a higher prevalence of worse perceived and mental health. These people and those who had had sex with persons of the same sex more frequently reported harmful health-related behaviors. Lesbian, gay, transgender and bisexual people may have health problems that should be explored in depth, prevented, and attended. Copyright © 2014 SESPAS. Published by Elsevier Espana. All rights reserved.

  8. Self-regulatory processes mediate the intention-behavior relation for adherence and exercise behaviors.

    Science.gov (United States)

    de Bruin, Marijn; Sheeran, Paschal; Kok, Gerjo; Hiemstra, Anneke; Prins, Jan M; Hospers, Harm J; van Breukelen, Gerard J P

    2012-11-01

    Understanding the gap between people's intentions and actual health behavior is an important issue in health psychology. Our aim in this study was to investigate whether self-regulatory processes (monitoring goal progress and responding to discrepancies) mediate the intention-behavior relation in relation to HIV medication adherence (Study 1) and intensive exercise behavior (Study 2). In Study 1, questionnaire and electronically monitored adherence data were collected at baseline and 3 months later from patients in the control arm of an HIV-adherence intervention study. In Study 2, questionnaire data was collected at 3 time points 6-weeks apart in a cohort study of physical activity. Complete data at all time points were obtained from 51 HIV-infected patients and 499 intensive exercise participants. Intentions were good predictors of behavior and explained 25 to 30% of the variance. Self-regulatory processes explained an additional 11% (Study 1) and 6% (Study 2) of variance in behavior on top of intentions. Regression and bootstrap analyses revealed at least partial, and possibly full, mediation of the intention-behavior relation by self-regulatory processes. The present studies indicate that self-regulatory processes may explain how intentions drive behavior. Future tests, using different health behaviors and experimental designs, could firmly establish whether self-regulatory processes complement current health behavior theories and should become routine targets for intervention. (PsycINFO Database Record (c) 2012 APA, all rights reserved).

  9. Association Between Substance Use and Gun-Related Behaviors.

    Science.gov (United States)

    Chen, Danhong; Wu, Li-Tzy

    2016-01-01

    Gun-related violence is a public health concern. This study synthesizes findings on associations between substance use and gun-related behaviors. Searches through PubMed, Embase, and PsycINFO located 66 studies published in English between 1992 and 2014. Most studies found a significant bivariate association between substance use and increased odds of gun-related behaviors. However, their association after adjustment was mixed, which could be attributed to a number of factors such as variations in definitions of substance use and gun activity, study design, sample demographics, and the specific covariates considered. Fewer studies identified a significant association between substance use and gun access/possession than other gun activities. The significant association between nonsubstance covariates (e.g., demographic covariates and other behavioral risk factors) and gun-related behaviors might have moderated the association between substance use and gun activities. Particularly, the strength of association between substance use and gun activities tended to reduce appreciably or to become nonsignificant after adjustment for mental disorders. Some studies indicated a positive association between the frequency of substance use and the odds of engaging in gun-related behaviors. Overall, the results suggest a need to consider substance use in research and prevention programs for gun-related violence. © The Author 2016. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  10. Pregnancy-related Health Behavior of Women with Congenital Heart Disease : Room for Behavioral Change Interventions

    NARCIS (Netherlands)

    Moons, Philip; Budts, Werner; Costermans, Els; Huyghe, Els; Pieper, Petronella G.; Drenthen, Wim

    2009-01-01

    Background. Pregnancy in women with congenital heart disease is associated with maternal and neonatal complications. In order to reduce risks for unfavorable outcomes, pregnant women need to adopt specific health behaviors. We investigated the pregnancy-related health behavior of women with

  11. Blocking Avoidance and Escape Responses: Relations With Clinically Relevant Behaviors

    Directory of Open Access Journals (Sweden)

    Juliana Maria Bubna Popovitz

    Full Text Available Abstract: The current study aims to evaluate the possible effects of interrupting problematic clinically relevant behaviors on the percentage of these responses and of clinical improvement-related responses. Two clients were treated with Functional Analytic Psychotherapy (FAP, alternating two conditions (ABAB. On condition A, procedures to the therapist consisted of responding to the clinical improvement responses, and to description of outside of therapeutic setting behaviors, but therapists were advised to ignore problem behaviors emitted in session. During condition B, therapists followed the same procedures, but they were oriented to block (interrupt problematic responses emitted in session. Results suggest increase in the percentage of problem behaviors during condition B. Results are discussed, highlighting the viability of planning the contingent response the therapist emits to clinically relevant behaviors.

  12. Relation of organizational citizenship behavior and locus of control.

    Science.gov (United States)

    Turnipseed, David L; Bacon, Calvin M

    2009-12-01

    The relation of organizational citizenship behavior and locus of control was assessed in a sample of 286 college students (52% men; M age = 24 yr.) who worked an average of 26 hr. per week. Measures were Spector's Work Locus of Control Scale and Podsakoff, et al.'s Organization Citizenship Behavior scale. Hierarchical multiple regressions indicated positive association of scores on work locus of control with scores on each of the four tested dimensions of organizational citizenship, as well as total organizational citizenship behavior.

  13. [Relational frame theory - a theoretical framework for contextual behavioral science].

    Science.gov (United States)

    Kensche, M; Schweiger, U

    2015-05-01

    Therapists have to deal with verbal systems and often work with verbal exchange. Therefore, a psychological theory is required, which teaches the therapist how to accomplish this task. The BRT is a theory of human language and cognition that explains how people use their verbal behavior as stimuli in their interrelations and how they act and react, based on the resulting relationships. This behavior is learned very early in the course of language acquisition and functions as a generalized operant. A prerequisite for this is the ability of people to undergo mental simulation. This enables them to construct diverse relational frameworks between individual stimuli. Without relational frameworks, people cannot function. The ability to establish a relational framework is a prerequisite for the formation of rule-governed behavior. Rule-governed behavior economizes complex decision processes, creates interpersonal security and enables dealing with events before they take place. On the other hand, the same properties that enable people to solve problems effectively can also contribute to rigid adherence to rules and experience avoidance. Relational frameworks, once established, outweigh other sources of behavioral regulation. Thus, it can become the basis of psychopathology. Poor contextual control makes it difficult for people to devote flexible, focused and voluntary attention to the present and align their actions with the immediate present. Contextual psychotherapy methods that are based on the BRT start precisely at this point: Targeted establishment of new contingencies in the therapeutic interaction through systematic strengthening of metacognitive mode and through the establishment of new rules that make possible a change in the rule-governed behavior enable undermining of dysfunctional rule-governed behavior and build up desirable behavior. This allows any therapeutic process to be more effective - regardless of the patient's expressed symptoms. © Georg Thieme

  14. Leadership Behaviors and Its Relation with Principals’ Management Experience

    Directory of Open Access Journals (Sweden)

    Vali Mehdinezhad

    2016-01-01

    Full Text Available This paper aims at studying the leadership behaviors reported by principals and observed by teachers and its relationship with management experience of principals. A quantitative method was used in this study. The target population included all principals and teachers of guidance schools and high schools in the Dashtiari District, Iran. A sample consisting of 46 principals and 129 teachers was selected by stratified sampling and simple random sampling methods. A leadership Behavior Description Questionnaire (LBDQ developed by Kozes and Posner (2001 was used for data collection. The obtained data were analyzed using one sample and independent t-test, correlation coefficient and crosstabs pearson Chi-square test. The results showed that teachers describe leadership behaviors of their principals relatively well. However, principals themselves evaluated their leadership behaviors as very well. Comparing between leadership behaviors self-reported by principals and those observed by teachers, a significant difference was found between the views and evaluations of teachers and principals on all components of leadership behaviors of principals, except that regarding empowerment. In fact, principals described their leadership behaviors better and at a more appropriate level than teachers. From the perspective of both teachers and principals, there was no significant relationship between any of the components of leadership behaviors and management experience of principals.

  15. Workplace bullying in Serbia: The relation of self-labeling and behavioral experience with job-related behaviors

    Directory of Open Access Journals (Sweden)

    Petrović Ivana B.

    2014-01-01

    Full Text Available Workplace bullying has been identified as a widespread problem in contemporary organizational research. The aim of the paper was to acquire theoretically based and comparable findings about workplace bullying in Serbia: to explore the behavioral experience and self-labeling approaches (applying the Negative Acts Questionnaire - Revised, NAQ-R and their relationship with job-related behaviors. The sample comprised 1,998 employees. Prevalence rates of workplace bullying based on self-labeling and behavior experience approaches overlap significantly (70% of employees operationally identified as bullied had also labeled themselves as bullied. Both the self-labeling and behavioral experience approach showed significant correlations with job-related behaviors (perceived threat to a total job, absenteeism, intention to leave, and perceived productivity. Previously bullied, presently bullied and non-bullied employees differed significantly on all four job-related behaviors, with large effect size for the intention to leave and medium effect size for the perceived threat to a total job. The findings support combining self-labeling and behavioral experience approaches in workplace bullying research. [Projekat Ministarstva nauke Republike Srbije, br. 179018

  16. Affective Influences on Energy-Related Decisions and Behaviors

    Energy Technology Data Exchange (ETDEWEB)

    Brosch, Tobias, E-mail: tobias.brosch@unige.ch [Department of Psychology, University of Geneva, Geneva (Switzerland); Swiss Center of Affective Sciences, University of Geneva, Geneva (Switzerland); Patel, Martin K. [Energy Group, Institute for Environmental Sciences, University of Geneva, Geneva (Switzerland); Energy Group, Forel Institute, University of Geneva, Geneva (Switzerland); Sander, David [Department of Psychology, University of Geneva, Geneva (Switzerland); Swiss Center of Affective Sciences, University of Geneva, Geneva (Switzerland)

    2014-03-17

    A successful energy transition will depend not only on the development of new energy technologies, but also on changes in the patterns of individual energy-related decisions and behaviors resulting in substantial reductions in energy demand. Across scientific disciplines, most theoretical approaches that try to understand energy-related decisions and behaviors focus mainly on cognitive processes, such as computations of utility (typically economic), the impact of cognitive heuristics, or the role of individual beliefs. While these models already explain important aspects of human decisions and behavior in the energy domain, we argue that an additional consideration of the contributions of emotional processes may be very fruitful for a deeper understanding of the issue. In this contribution, we outline a theoretical perspective on energy-related decisions and behaviors that integrates emotions, elicited by a cognitive-affective appraisal of the relevance of a situation, into a response system driving adaptive decisions and behaviors. We empirically investigate the explanatory power of the model variables to predict intentions to reduce energy use demonstrating that the appraisal–emotion variables are able to account for additional variance that is not explained by two established models focused on cognitive processes (theory of planned behavior and value-belief-norm theory). Finally, we discuss how the appraisal–emotion approach may be fruitfully integrated with other existing approaches and outline some questions for future research.

  17. Affective Influences on Energy-Related Decisions and Behaviors

    International Nuclear Information System (INIS)

    Brosch, Tobias; Patel, Martin K.; Sander, David

    2014-01-01

    A successful energy transition will depend not only on the development of new energy technologies, but also on changes in the patterns of individual energy-related decisions and behaviors resulting in substantial reductions in energy demand. Across scientific disciplines, most theoretical approaches that try to understand energy-related decisions and behaviors focus mainly on cognitive processes, such as computations of utility (typically economic), the impact of cognitive heuristics, or the role of individual beliefs. While these models already explain important aspects of human decisions and behavior in the energy domain, we argue that an additional consideration of the contributions of emotional processes may be very fruitful for a deeper understanding of the issue. In this contribution, we outline a theoretical perspective on energy-related decisions and behaviors that integrates emotions, elicited by a cognitive-affective appraisal of the relevance of a situation, into a response system driving adaptive decisions and behaviors. We empirically investigate the explanatory power of the model variables to predict intentions to reduce energy use demonstrating that the appraisal–emotion variables are able to account for additional variance that is not explained by two established models focused on cognitive processes (theory of planned behavior and value-belief-norm theory). Finally, we discuss how the appraisal–emotion approach may be fruitfully integrated with other existing approaches and outline some questions for future research.

  18. Affective influences on energy-related decisions and behaviors

    Directory of Open Access Journals (Sweden)

    Tobias eBrosch

    2014-03-01

    Full Text Available A successful energy transition will depend not only on the development of new energy technologies, but also on changes in the patterns of individual energy-related decisions and behaviors resulting in substantial reductions in energy demand. Across scientific disciplines, most theoretical approaches that try to understand energy-related decisions and behaviors focus mainly on cognitive processes, such as computations of utility (typically economic, the impact of cognitive heuristics, or the role of individual beliefs. While these models already explain important aspects of human decisions and behavior in the energy domain, we argue that an additional consideration of the contributions of emotional processes may be very fruitful for a deeper understanding of the issue. In this contribution, we outline a theoretical perspective on energy-related decisions and behaviors that integrates emotions, elicited by a cognitive-affective appraisal of the relevance of a situation, into a response system driving adaptive decisions and behaviors. We empirically investigate the explanatory power of the model variables to predict intentions to reduce energy use, demonstrating that the appraisal-emotion variables are able to account for additional variance that is not explained by two established models focused on cognitive processes (Theory of Planned Behavior and Value-Belief-Norm Theory. Finally, we discuss how the appraisal-emotion approach may be fruitfully integrated with other existing approaches and outline some questions for future research.

  19. Influence of the alloying elements vanadium, chromium and carbon on the electrochemical behavior of uranium in media with a pH 13 or a pH acid

    International Nuclear Information System (INIS)

    Pommier, Gerard; Jouve, Gerard; Lacombe, Paul.

    1976-06-01

    The electrochemical properties of uranium alloys with low vanadium and chromium contents were studied in aqueous medium for different pH values of the solution (pH between 0 and 5 in H 2 SO 4 medium and pH=13 in NaOH medium). In acid medium, the study of the behavior of the two types of alloys carried out by the potentiokinetic method is described. The specific role of chromium concerning the anodic process is demonstrated and the influence of vanadium in specimens of same nominal vanadium contents but different carbon contents is revealed by the modification of the reduction overvoltage of water. In basic medium, the electrochemical study was supported by an optical method of determining the relative growth kinetics of the films in situ and continuously. At lower values of potential, the growth of an oxide film of UO 2 with linear growth kinetics is demonstrated; at higher values of potential a system of two layers is observed and its evolution is followed kinematically. The film initially formed is constituted of an oxide UO 3 2H 2 O, and its growth is linear, then a film of UO 2 develops underneath. A structural evolution of the superficial film is then observed, an evolution which leads to its cracking after breakdown. These phenomena were followed by electron microscopy using a technic of two stage replicas [fr

  20. Mechanism of potentiostatic deposition of MnO2 and electrochemical characteristics of the deposit in relation to carbohydrate oxidation

    International Nuclear Information System (INIS)

    Das, Debasmita; Sen, Pratik Kumar; Das, Kaushik

    2008-01-01

    Cyclic voltammetric (CV) and chronoamperometric (CA) studies on potentiostatic deposition of MnO 2 on Pt from Mn(II) solution in very weakly alkaline media show the process to be controlled by a one-electron transfer step, which means that the deposition proceeds through the generation of Mn(III). The electrocatalytic activity of the deposited electrode towards carbohydrate oxidation is found to be maximum at an optimum amount of deposition. Chronopotentiometric (CP) and CV measurements show that the oxidation of carbohydrates on the deposited electrodes follows a catalytic EC (electrochemical-chemical) mechanism via electrolytic formation of Mn(V) and its subsequent consumption either by disproportionation or by chemical reaction in the presence of carbohydrates. The rate constants of the reaction of Mn(V) with dextrose and fructose have been obtained from CA results. The relative order of the oxidation currents for dextrose and fructose as well as their dependence on carbohydrate concentration has been discussed. Replacement of Pt by carbon as the electrode support material does not affect the electrocatalytic activity of the MnO 2 deposit. The observed linear variation of the steady state oxidation currents with carbohydrate concentration can be exploited for analytical application

  1. Electrochemical biosensors

    CERN Document Server

    Cosnier, Serge

    2015-01-01

    "This is an excellent book on modern electrochemical biosensors, edited by Professor Cosnier and written by leading international experts. It covers state-of-the-art topics of this important field in a clear and timely manner."-Prof. Joseph Wang, UC San Diego, USA  "This book covers, in 13 well-illustrated chapters, the potential of electrochemical methods intimately combined with a biological component for the assay of various analytes of biological and environmental interest. Particular attention is devoted to the description of electrochemical microtools in close contact with a biological cell for exocytosis monitoring and to the use of nanomaterials in the electrochemical biosensor architecture for signal improvement. Interestingly, one chapter describes the concept and design of self-powered biosensors derived from biofuel cells. Each topic is reviewed by experts very active in the field. This timely book is well suited for providing a good overview of current research trends devoted to electrochemical...

  2. Impulsivity traits and addiction-related behaviors in youth

    DEFF Research Database (Denmark)

    Rømer Thomsen, Kristine; Callesen, Mette Buhl; Hesse, Morten

    2018-01-01

    problems to achieve a broad distribution of involvement in addiction-related behaviors. Participants completed the UPPS-P Questionnaire and standardized questionnaires assessing problematic use of substances (alcohol, cannabis, and other drugs) and non-substances (Internet gaming, pornography, and food...... eating and lack of perseverance was associated with problematic use of pornography. Discussion and conclusions We emphasize the role of trait impulsivity across multiple addiction-related behaviors. Our findings in at-risk youth highlight urgency and lack of perseverance as potential predictors...

  3. Development of Ionic Liquid Modified Disposable Graphite Electrodes for Label-Free Electrochemical Detection of DNA Hybridization Related to Microcystis spp.

    Directory of Open Access Journals (Sweden)

    Ceren Sengiz

    2015-09-01

    Full Text Available In this present study, ionic liquid (1-butyl-3-methylimidazolium hexafluorophosphate (IL modified pencil graphite electrode (IL-PGEs was developed for electrochemical monitoring of DNA hybridization related to Microcystis spp. (MYC. The characterization of IL-PGEs was performed using microscopic and electrochemical techniques. DNA hybridization related to MYC was then explored at the surface of IL-PGEs using differential pulse voltammetry (DPV technique. After the experimental parameters were optimized, the sequence-selective DNA hybridization related to MYC was performed in the case of hybridization between MYC probe and its complementary DNA target, noncomplementary (NC or mismatched DNA sequence (MM, or and in the presence of mixture of DNA target: NC (1:1 and DNA target: MM (1:1.

  4. Low-crystallinity molybdenum sulfide nanosheets assembled on carbon nanotubes for long-life lithium storage: Unusual electrochemical behaviors and ascending capacities

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaodan, E-mail: xiaodan_li@yeah.net [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China ElectricPower University, Beijing, 102206 (China); Wu, Gaoxiang, E-mail: wgxjimmy@126.com [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China ElectricPower University, Beijing, 102206 (China); Chen, Jiewei, E-mail: kzscjw@126.com [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China ElectricPower University, Beijing, 102206 (China); Li, Meicheng, E-mail: mcli@ncepu.edu.cn [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China ElectricPower University, Beijing, 102206 (China); Chongqing Materials Research Institute, Chongqing 400707 (China); Li, Wei, E-mail: wei.li@inl.int [International Iberian Nanotechnology Laboratory (INL), Braga 4715-330 (Portugal); Wang, Tianyue, E-mail: 1355796015@qq.com [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China ElectricPower University, Beijing, 102206 (China); Jiang, Bing, E-mail: BingJiang@ncepu.edu.cn [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China ElectricPower University, Beijing, 102206 (China); He, Yue, E-mail: 947667748@qq.com [State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China ElectricPower University, Beijing, 102206 (China); Mai, Liqiang, E-mail: mlq518@whut.edu.cn [State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070 (China)

    2017-01-15

    Highlights: • Low-crystallinity molybdenum sulfide coated on carbon nanotubes were synthesized. • This anode material has unusual electrochemical behaviors compared to typical MoS{sub 2}. • It exhibits noticable ascending trends in capacity and superior rate performance. • The ascending performance can effectively extend the circulation life of batteries. - Abstract: Low-crystallinity molybdenum sulfide (LCMS, Mo:S = 1:2.75) nanosheets synthesized by a facile and low temperature solvothermal method is now reported. The as-prepared LCMS anode material is composited of MoS{sub 2} layers mixed with amorphous MoS{sub 3}, which leads to an unusual electrochemical process for lithium storage compared to typical MoS{sub 2} anode. The existence of MoS{sub 3} and Mo (VI) provide strong adsorption and binding sites for polar polysulphides, which compels abundant sulfur to turn into new-formed MoS{sub 3} rather than diffuse into electrolyte. To fully utilize this novel electrochemical process, LCMS is decorated on carbon nanotubes, obtaining well-dispersed CNTs@LCMS. As electrode material for lithium storage, CNTs@LCMS exhibits a noticable ascending trend in capacity from 820 mA h g{sup −1} to 1350 mA h g{sup −1} at 100 mA g{sup −1} during 130 cycles. The persistent ascending capacity is ascribed to the increasing lithium storage caused by new-formed MoS{sub 3}, combined with the reduced volume change benifiting from well-dispersed CNTs@LCMS. Furthermore, the ascending performance is proved to be able to effectively extend the circulation life (up to 200%) for lithium-ion batteries by mathematical modeling and calculation. Accordingly, the CNTs@LCMS composite is a promising anode material for long-life lithium-ion batteries.

  5. Health-related behaviors among pregnant women with hypertension

    Directory of Open Access Journals (Sweden)

    Agnieszka Maria Bień

    2017-01-01

    Full Text Available Introduction. The healthy and unhealthy behaviors of a pregnant woman influence both her own health and that of her unborn child, affecting its future development. The purpose of the study was to evaluate the health-related behaviors of pregnant women with hypertension.   Material i method. The study was performed between November 2011 and February 2012 and included 80 hypertensive pregnant women hospitalized in a high risk pregnancy ward. The study used a diagnostic survey with questionnaires. Results. Statistical analyses showed a correlation between the respondents’ health-related behaviors and their socio-demographic characteristics: exercise was correlated with age (p=0.01, and rest during the day was correlated with support in everyday responsibilities (p<0.00001, and with the respondents’ socio-economic standing (p=0.03. Correlations were also found between healthy eating habits and residence (0.006, education (p=0.05, and sodium intake (p=0.0003, as well as between education and substance use (p=0.0003. Conclusion. Health-related behaviors of pregnant women with hypertension are influenced by their education, support they receive in daily responsibilities, and their socio-economic standing. The diagnosis of hypertension in pregnant women does not necessarily prompt them to discontinue all unhealthy behaviors.

  6. Nightmare frequency is related to a propensity for mirror behaviors.

    Science.gov (United States)

    Nielsen, Tore; Powell, Russell A; Kuiken, Don

    2013-12-01

    behaviors during wakefulness, while among males nightmares are associated with threat-related mirror behaviors during wakefulness. They thus support the possibility that the association between mirror behaviors and dream-enacting behaviors is due to a common mirror neuron mechanism that underlies mirror behaviors and nightmares and that involves motor, rather than emotional, resonance. These results have implications for understanding the comorbidity of nightmares and other pathological symptoms such as imitative suicidal behaviors, the influence of observational learning on dissociative symptomatology, and the predominance of threat and aggression in the dream enacting behaviors of REM sleep behavior disorder. Copyright © 2013 Elsevier Inc. All rights reserved.

  7. Characterization, liquid crystalline behavior, electrochemical and optoelectrical properties of new poly(azomethine)s and a poly(imide) with siloxane linkages

    Science.gov (United States)

    Iwan, Agnieszka; Schab-Balcerzak, Ewa; Pociecha, Damian; Krompiec, Michal; Grucela, Marzena; Bilski, Pawel; Kłosowski, Mariusz; Janeczek, Henryk

    2011-11-01

    New siloxane-containing poly(azomethine)s and a six-membered poly(imide) have been developed from siloxane-containing diamine with four different dialdehydes and 3,4,9,10-perylenetetracarboxylic dianhydride, and their thermotropic behavior, optoelectrical and electrochemical properties were examined. Mesomorphic behavior of the polymers was investigated via differential scanning calorimetry (DSC), polarizing optical microscopy (POM) and X-ray diffraction (WAXRD, SAXRD) studies. The electrochemical behavior of poly(azomethine)s and poly(imide) was studied by differential pulse voltammetry (DPV). The HOMO levels of these polymers were in the range of -5.13 to -5.90 eV. UV-vis properties of the polymers were investigated in solid state as thin films and in chloroform solution. Optical energy band gap ( Egopt.) was calculated from absorption spectra and absorption coefficients α. The photoluminescence properties (PL) of obtained polymers were studied in chloroform solution. The investigated poly(azomethine)s emitted blue light, while the poly(imide) emitted green light. The polymers were irradiated with a test dose of 1 Gy Co-60 gamma-rays to detect their thermoluminescence properties in the temperature range of 50-200 °C. Polymer monolayer (ITO/polymer/Al) and bulk heterojunction (BHJ) (ITO/polymer:PCBM/Al and ITO/PEDOT:PSS/polymer:PCBM/Al) devices were prepared with PAZ and PI used as active layers and I- U curves were measured in the dark and during irradiation with light (under illumination of 1000 W/m 2). Poly(azomethine)s were blended with [6,6]-phenyl C 61 butyric acid methyl ester (PCBM). Selected properties of the investigated polymers with siloxane linkages were compared with the polymers ( PAZ1a- PAZ3a, PIa) prepared from the same dialdehydes or dianhydride and poly(1,4-butanediol)bis(4-aminobenzoate).

  8. The dynamic behavior of thin-film ionic transition metal complex-based light-emitting electrochemical cells

    Energy Technology Data Exchange (ETDEWEB)

    Meier, Sebastian B., E-mail: sebastian.meier@belectric.com, E-mail: wiebke.sarfert@siemens.com [Department of Materials Science VI: Materials for Electronics and Energy Technology, Friedrich-Alexander-University of Erlangen-Nuremberg, 91058 Erlangen (Germany); Siemens AG, Corporate Technology, CT RTC MAT IEC-DE, 91058 Erlangen (Germany); Hartmann, David; Sarfert, Wiebke, E-mail: sebastian.meier@belectric.com, E-mail: wiebke.sarfert@siemens.com [Siemens AG, Corporate Technology, CT RTC MAT IEC-DE, 91058 Erlangen (Germany); Winnacker, Albrecht [Department of Materials Science VI: Materials for Electronics and Energy Technology, Friedrich-Alexander-University of Erlangen-Nuremberg, 91058 Erlangen (Germany)

    2014-09-14

    Light-emitting electrochemical cells (LECs) have received increasing attention during recent years due to their simple architecture, based on solely air-stabile materials, and ease of manufacture in ambient atmosphere, using solution-based technologies. The LEC's active layer offers semiconducting, luminescent as well as ionic functionality resulting in device physical processes fundamentally different as compared with organic light-emitting diodes. During operation, electrical double layers (EDLs) form at the electrode interfaces as a consequence of ion accumulation and electrochemical doping sets in leading to the in situ development of a light-emitting p-i-n junction. In this paper, we comment on the use of impedance spectroscopy in combination with complex nonlinear squares fitting to derive key information about the latter events in thin-film ionic transition metal complex-based light-emitting electrochemical cells based on the model compound bis-2-phenylpyridine 6-phenyl-2,2´-bipyridine iridium(III) hexafluoridophosphate ([Ir(ppy)₂(pbpy)][PF₆]). At operating voltages below the bandgap potential of the ionic complex used, we obtain the dielectric constant of the active layer, the conductivity of mobile ions, the transference numbers of electrons and ions, and the thickness of the EDLs, whereas the transient thickness of the p-i-n junction is determined at voltages above the bandgap potential. Most importantly, we find that charge transport is dominated by the ions when carrier injection from the electrodes is prohibited, that ion movement is limited by the presence of transverse internal interfaces and that the width of the intrinsic region constitutes almost 60% of the total active layer thickness in steady state at a low operating voltage.

  9. Density functional theory and surface enhanced Raman spectroscopy studies of tautomeric hypoxanthine and its adsorption behaviors in electrochemical processes

    International Nuclear Information System (INIS)

    Huang, Wei; Jiang, Jin-Zhi; Chen, Liang; Zhang, Bi-Qi; Deng, Shu-Fen; Sun, Jian Jun; Chen, Wen-Kai

    2015-01-01

    ABSTRACT: Hypoxanthine, a purine heterocyclic compound with N and O atoms, has capability to combine metal ions or adsorb on metals. By using density functional theory (DFT) method calculation, the energy, charge distribution, molecular orbital and vibration spectra information of tautomeric hypoxanthine were given. Combined with these DFT results, the influence of pH on the structure of tautomeric hypoxanthine was studied by surface enhanced Raman spectroscopy (SERS). Electrochemical SERS was applied to study the properties of hypoxanthine/gold interface. It is found that the structure of adsorbed hypoxanthine was changed from slightly tilted to upright with negatively moving of potentials

  10. Comparative study of the influence of antimony oxide additives (III) and nickel hydroxide (II) on electrochemical behavior of cadmium electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Kadnikova, N.V.; Lvova, L.A.; Ryabskaya, I.A.

    1983-01-01

    Comparative study of the influence of additives indicated that with partial or complete replacement in the active mass of the cadmium electrode of nickel hydroxide (II) by antimony oxide (III), the electrochemical characteristics do not significantly change. During prolonged storage of charged cadmium electrodes the presence of nickel hydroxide (II) and intermetal compound (IMC) of cadmium with nickel is formed and the specific surface increases. In the case of adding antimony (III) formation of noticeable quantities of IMC of cadmium with antimony is not observed. The specific surface is reduced during storage.

  11. Antisocial Behavior and Depressive Symptoms: Longitudinal and Concurrent Relations

    Science.gov (United States)

    Vieno, Alessio; Kiesner, Jeff; Pastore, Massimiliano; Santinello, Massimo

    2008-01-01

    The relations between antisocial behavior and depressive symptoms were examined both longitudinally and concurrently in a sample of Italian early-adolescents. Structural equation modelling was applied to 10-month longitudinal data from a sample of 107 youths (54 girls; mean age at baseline = M = 12.5). Early adolescents completed a questionnaire…

  12. Adolescent antisocial behavior explained by combining stress-related parameters

    NARCIS (Netherlands)

    Platje, Evelien; Jansen, Lucres M. C.; Vermeiren, Robert R. J. M.; Doreleijers, Theo A. H.; van Lier, Pol A. C.; Koot, Hans M.; Meeus, W.H.J.; Branje, Suzan J. T.; Popma, Arne

    Many stress-related parameters have been associated with antisocial behavior, including low cortisol awakening responses (CAR), as well as low cortisol and alpha-amylase reactivity to stress. These parameters reflect different, yet interrelated components of the stress system, yet it remains to be

  13. Bidirectional Relations between Authoritative Parenting and Adolescents' Prosocial Behaviors

    Science.gov (United States)

    Padilla-Walker, Laura M.; Carlo, Gustavo; Christensen, Katherine J.; Yorgason, Jeremy B.

    2012-01-01

    This study examined the bidirectional relations between authoritative parenting and adolescents' prosocial behavior over a 1-year time period. Data were taken from Time 2 and 3 of the Flourishing Families Project, and included reports from 319 two-parent families with an adolescent child (M age of child at Time 2 = 12.34, SD = 1.06, 52% girls).…

  14. Investigating privacy attitudes and behavior in relation to personalization

    NARCIS (Netherlands)

    Garde - Perik, van de E.M.; Markopoulos, P.; Ruyter, de B.E.R.; Eggen, J.H.; IJsselsteijn, W.A.

    2008-01-01

    This article presents an experimental study of privacy-related attitudes and behaviors regarding a music recommender service based on two types of user modeling: personality traits and musical preferences. Contrary to prior expectations and attitudes reported by participants, personality traits are

  15. Another Look at Gender-Related Differences in Leadership Behavior

    Science.gov (United States)

    Winther, Dorothy; Green, Samuel, B.

    1987-01-01

    Examines self-related behavioral differences in terms of broad leadership styles. While male leaders used a more social style than female leaders, both male and female leaders used language that indicated a task-oriented approach to a significantly greater degree when instructing a female rather than a male subordinate. (Author/LHW)

  16. Investigation of the temperature effect on electrochemical behaviors of TiO2 for gel type valve regulated lead-acid batteries

    Directory of Open Access Journals (Sweden)

    Metin GENÇTEN

    2016-12-01

    Full Text Available In this study, the effect of temperature on the electrochemical behaviors of gel electrolyte systems was investigated for valve regulated lead-acid battery at 0≤ T ≤50 oC. Fumed silica and mixture of fumed silica and TiO2 were used as gel electrolytes. TiO2 has a good combination with fumed silica. They were characterized by cyclic voltammetry, electrochemical impedance spectroscopy and battery tests. The anodic peak currents and redox capacities of the gel electrolytes increased with increasing of temperature. The highest anodic peak current and redox capacity were observed at 30 oC in fumed silica and at 40 oC in fumed silica:TiO2 based gel systems. The solution and charge transfer resistance values decreased in fumed silica:TiO2 gel system by increasing temperature. In battery tests, discharge curves were obtained for each gel system at 0, 25 and 50 oC. The discharge time of mixture gel electrolyte system was higher than that of fumed silica based gel electrolyte at low (0 oC and high (50 oC temperatures. The best performance was obtained in fumed silica based gel electrolyte at 25 oC.

  17. Coupling of Mechanical Behavior of Lithium Ion Cells to Electrochemical-Thermal Models for Battery Crush; NREL (National Renewable Energy Laboratory)

    Energy Technology Data Exchange (ETDEWEB)

    Pesaran, Ahmad; Zhang, Chao; Santhanagopalan, Shriram; Sahraei, Elham; Wierzbiki, Tom

    2015-06-15

    Propagation of failure in lithium-ion batteries during field events or under abuse is a strong function of the mechanical response of the different components in the battery. Whereas thermal and electrochemical models that capture the abuse response of batteries have been developed and matured over the years, the interaction between the mechanical behavior and the thermal response of these batteries is not very well understood. With support from the Department of Energy, NREL has made progress in coupling mechanical, thermal, and electrochemical lithium-ion models to predict the initiation and propagation of short circuits under external crush in a cell. The challenge with a cell crush simulation is to estimate the magnitude and location of the short. To address this, the model includes an explicit representation of each individual component such as the active material, current collector, separator, etc., and predicts their mechanical deformation under different crush scenarios. Initial results show reasonable agreement with experiments. In this presentation, the versatility of the approach for use with different design factors, cell formats and chemistries is explored using examples.

  18. Nicotinamide-NAD sequence: redox process and related behavior, behavior and properties of intermediate and final products

    International Nuclear Information System (INIS)

    Elving, P.J.; Schmakel, C.O.; Santhanam, K.S.V.

    1976-01-01

    Illustrations of the application of analytical chemical techniques to the study of chemical phenomena are given. In particular, electrochemical techniques and methodology and, to a lesser extent, spectrophotometry were used to investigate the solution behavior, adsorption, redox processes including coupled chemical reactions, and allied aspects of biologically significant compounds and of their intermediate and final redox products, e.g., the behavior of the free radicals produced by initial one-electron processes. This approach is illustrated by the consideration of the behavior in aqueous and nonaqueous media of a sequence of compounds ranging from nicotinamide (3-carbamoylpyridine) to NAD + and NADP + ; the latter compounds function as coenzymes for the pyridinoproteins which are principal components in the Krebs citric acid cycle and in the electron transport chain in biological redox reactions. The discussion is presented under the following section headings: interpretation of electrochemical behavior; mechanistic patterns; kinetic aspects of charge-transfer and chemical reactions; correlation with theoretically calculated parameters; and, mechanisms of biological oxidation-reduction reactions. The use of pulse radiolysis, chronopotentiometric, and cyclic voltammetric methods in studies on free radical dimerization rates is reviewed in the discussion of the kinetic aspects of charge-transfer and chemical reactions. (188 references)

  19. Cognitive-Behavioral Therapy: Nature and Relation to Non-Cognitive Behavioral Therapy.

    Science.gov (United States)

    Lorenzo-Luaces, Lorenzo; Keefe, John R; DeRubeis, Robert J

    2016-11-01

    Since the introduction of Beck's cognitive theory of emotional disorders, and their treatment with psychotherapy, cognitive-behavioral approaches have become the most extensively researched psychological treatment for a wide variety of disorders. Despite this, the relative contribution of cognitive to behavioral approaches to treatment are poorly understood and the mechanistic role of cognitive change in therapy is widely debated. We critically review this literature, focusing on the mechanistic role of cognitive change across cognitive and behavioral therapies for depressive and anxiety disorders. Copyright © 2016. Published by Elsevier Ltd.

  20. Effect of N{sub 2} flow rate on the microstructure and electrochemical behavior of TaN{sub x} films deposited by modulated pulsed power magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Mendizabal, L., E-mail: lucia.mendizabal@tekniker.es [IK4-TEKNIKER, Department of Surface Physics and Technology, Iñaki Goenaga 5, 20600 Eibar (Spain); Bayón, R. [IK4-TEKNIKER, Department of Tribology, Iñaki Goenaga 5, 20600 Eibar (Spain); G-Berasategui, E.; Barriga, J. [IK4-TEKNIKER, Department of Surface Physics and Technology, Iñaki Goenaga 5, 20600 Eibar (Spain); Gonzalez, J.J. [ETSIB University of Basque Country, Department of Material Science, Alameda de Urquijo s/n, 48013 Bilbao (Spain)

    2016-07-01

    Modulated pulsed power magnetron sputtering (MPPMS) technology offers the possibility to grow high performance coatings compared to the ones developed by conventional dc magnetron sputtering. The high degree of ionization of sputtered particles developed during MPPMS can be usefully utilized to precisely tailor the properties of the growing films. One of the main advantages of such a high metal ion flux is related to the densification of the coatings due to enhance ion bombardment towards the growing film. The development of extremely dense and low-defect microstructure coatings can have a positive effect on the corrosion resistance of tantalum nitride (TaN{sub x}) films. In this study, TaN{sub x} thin films have been deposited by MPPMS in a closed field unbalanced magnetron sputtering system. Structure, surface morphology, hardness and corrosion resistance of the developed coatings have been analyzed as a function of different N{sub 2}-to-Ar ratios (0, 0.25, 0.625, 1). X-ray diffraction and scanning electron microscopy analysis reveal high dependence of the grown crystal phases and the microstructure on N{sub 2}-to-Ar ratio. The hardness of the TaN{sub x} coatings increases when increasing N{sub 2}-to-Ar ratio up to a maximum value of 25 GPa (N{sub 2}-to-Ar ratio of 0.625). The corrosion behavior was investigated using electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry. EIS measurements registered at different immersion times show high impedance values (in the order of 10 MΩ cm{sup 2}) and corrosion resistance enhancement with time, indicating the formation of a passive protective oxide layer on the top of their surfaces. TaN{sub x} film grown at 0.25 N{sub 2}-to-Ar ratio exhibits the highest corrosion resistance of 103.53 MΩ cm{sup 2} and low porosity of 1.63 × 10{sup −3} and is characterized by columnar-free microstructure. - Highlights: • TaN{sub X} coatings deposited by MPPMS at different N{sub 2}-to-Ar ratios have been

  1. Effect of N_2 flow rate on the microstructure and electrochemical behavior of TaN_x films deposited by modulated pulsed power magnetron sputtering

    International Nuclear Information System (INIS)

    Mendizabal, L.; Bayón, R.; G-Berasategui, E.; Barriga, J.; Gonzalez, J.J.

    2016-01-01

    Modulated pulsed power magnetron sputtering (MPPMS) technology offers the possibility to grow high performance coatings compared to the ones developed by conventional dc magnetron sputtering. The high degree of ionization of sputtered particles developed during MPPMS can be usefully utilized to precisely tailor the properties of the growing films. One of the main advantages of such a high metal ion flux is related to the densification of the coatings due to enhance ion bombardment towards the growing film. The development of extremely dense and low-defect microstructure coatings can have a positive effect on the corrosion resistance of tantalum nitride (TaN_x) films. In this study, TaN_x thin films have been deposited by MPPMS in a closed field unbalanced magnetron sputtering system. Structure, surface morphology, hardness and corrosion resistance of the developed coatings have been analyzed as a function of different N_2-to-Ar ratios (0, 0.25, 0.625, 1). X-ray diffraction and scanning electron microscopy analysis reveal high dependence of the grown crystal phases and the microstructure on N_2-to-Ar ratio. The hardness of the TaN_x coatings increases when increasing N_2-to-Ar ratio up to a maximum value of 25 GPa (N_2-to-Ar ratio of 0.625). The corrosion behavior was investigated using electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry. EIS measurements registered at different immersion times show high impedance values (in the order of 10 MΩ cm"2) and corrosion resistance enhancement with time, indicating the formation of a passive protective oxide layer on the top of their surfaces. TaN_x film grown at 0.25 N_2-to-Ar ratio exhibits the highest corrosion resistance of 103.53 MΩ cm"2 and low porosity of 1.63 × 10"−"3 and is characterized by columnar-free microstructure. - Highlights: • TaN_X coatings deposited by MPPMS at different N_2-to-Ar ratios have been evaluated. • Columnar-free microstructure TaN_x films are obtained at 0

  2. A Contextual Behavior Science Framework for Understanding How Behavioral Flexibility Relates to Anxiety.

    Science.gov (United States)

    Palm Reed, Kathleen M; Cameron, Amy Y; Ameral, Victoria E

    2017-09-01

    There is a growing literature focusing on the emerging idea that behavioral flexibility, rather than particular emotion regulation strategies per se, provides greater promise in predicting and influencing anxiety-related psychopathology. Yet this line of research and theoretical analysis appear to be plagued by its own challenges. For example, middle-level constructs, such as behavioral flexibility, are difficult to define, difficult to measure, and difficult to interpret in relation to clinical interventions. A key point that some researchers have made is that previous studies examining flexible use of emotion regulation strategies (or, more broadly, coping) have failed due to a lack of focus on context. That is, examining strategies in isolation of the context in which they are used provides limited information on the suitability, rigid adherence, or effectiveness of a given strategy in that situation. Several of these researchers have proposed the development of new models to define and measure various types of behavioral flexibility. We would like to suggest that an explanation of the phenomenon already exists and that we can go back to our behavioral roots to understand this phenomenon rather than focusing on defining and capturing a new process. Indeed, thorough contextual behavioral analyses already yield a useful account of what has been observed. We will articulate a model explaining behavioral flexibility using a functional, contextual framework, with anxiety-related disorders as an example.

  3. Methanol oxidation reaction on core-shell structured Ruthenium-Palladium nanoparticles: Relationship between structure and electrochemical behavior

    Science.gov (United States)

    Kübler, Markus; Jurzinsky, Tilman; Ziegenbalg, Dirk; Cremers, Carsten

    2018-01-01

    In this work the relationship between structural composition and electrochemical characteristics of Palladium(Pd)-Ruthenium(Ru) nanoparticles during alkaline methanol oxidation reaction is investigated. The comparative study of a standard alloyed and a precisely Ru-core-Pd-shell structured catalyst allows for a distinct investigation of the electronic effect and the bifunctional mechanism. Core-shell catalysts benefit from a strong electronic effect and an efficient Pd utilization. It is found that core-shell nanoparticles are highly active towards methanol oxidation reaction for potentials ≥0.6 V, whereas alloyed catalysts show higher current outputs in the lower potential range. However, differential electrochemical mass spectrometry (DEMS) experiments reveal that the methanol oxidation reaction on core-shell structured catalysts proceeds via the incomplete oxidation pathway yielding formaldehyde, formic acid or methyl formate. Contrary, the alloyed catalyst benefits from the Ru atoms at its surface. Those are found to be responsible for high methanol oxidation activity at lower potentials as well as for complete oxidation of CH3OH to CO2 via the bifunctional mechanism. Based on these findings a new Ru-core-Pd-shell-Ru-terrace catalyst was synthesized, which combines the advantages of the core-shell structure and the alloy. This novel catalyst shows high methanol electrooxidation activity as well as excellent selectivity for the complete oxidation pathway.

  4. The psychosocial and behavioral characteristics related to energy misreporting.

    Science.gov (United States)

    Maurer, Jaclyn; Taren, Douglas L; Teixeira, Pedro J; Thomson, Cynthia A; Lohman, Timothy G; Going, Scott B; Houtkooper, Linda B

    2006-02-01

    Energy underreporting occurs in 2% to 85% and overreporting in 1% to 39% of various populations. Efforts are needed to understand the psychosocial and behavioral characteristics associated with misreporting to help improve the accuracy of dietary self-reporting. Past research suggests that higher social desirability and greater eating restraint are key factors influencing misreporting, while a history of dieting and being overweight are more moderately associated. Eating disinhibition, body image, depression, anxiety, and fear of negative evaluation may be related to energy misreporting, but evidence is insufficient. This review will provide a detailed discussion of the published associations among psychosocial and behavioral characteristics and energy misreporting.

  5. BEHAVIOR PRE-SET IN RELATIONS INTERPERSONAL ORGANIZATIONAL

    Directory of Open Access Journals (Sweden)

    Newton Fernandes de Ávila

    2015-12-01

    Full Text Available This article provides a study on the behavior and communication, and takes care not only to inform, but to reflect the actions and reactions in a contemporary universe. Thus, to achieve the proposed objective, it sought as methodology, the theoretical framework related to knowledge and communication in organizations. Thus, there was the need of the individual to be constantly learning in order to create and establish close between the action and the ability to push boundaries, not limited knowledge at the thought, but the practical application of communication, permeating the perception and modifying behaviors.

  6. Electrochemical Label-Free Aptasensor for Specific Analysis of Dopamine in Serum in the Presence of Structurally Related Neurotransmitters.

    Science.gov (United States)

    Álvarez-Martos, Isabel; Ferapontova, Elena E

    2016-04-05

    Cellular and brain metabolism of dopamine can be correlated with a number of neurodegenerative disorders, and as such, in vivo analysis of dopamine in the presence of structurally related neurotransmitters (NT) represents a holy grail of neuroscience. Interference from those NTs generally does not allow selective electroanalysis of dopamine, which redox transformation overlaps with those of other catecholamines. In our previous work, we reported an electrochemical RNA-aptamer-based biosensor for specific analysis of dopamine (Analytical Chemistry, 2013; Vol. 85, p 121). However, the overall design of the biosensor restricted its stability and impeded its operation in serum. Here, we show that specific biorecognition and electroanalysis of dopamine in serum can be performed by the RNA aptamer tethered to cysteamine-modified gold electrodes via the alkanethiol linker. The stabilized dopamine aptasensor allowed continuous 20 h amperometric analysis of dopamine in 10% serum within the physiologically important 0.1-1 μM range and in the presence of catechol and such dopamine precursors and metabolites as norepinephrine and l-DOPA. In a flow-injection mode, the aptasensor response to dopamine was ∼1 s, the sensitivity of analysis, optimized by adjusting the aptamer surface coverage, was 67 ± 1 nA μM(-1) cm(-2), and the dopamine LOD was 62 nM. The proposed design of the aptasensor, exploiting both the aptamer alkanethiol tethering to the electrode and screening of the catecholamine-aptamer electrostatic interactions, allows direct monitoring of dopamine levels in biological fluids in the presence of competitive NT and thus may be further applicable in biomedical research.

  7. Hide-and-Seek: Narcissism and "Selfie"-Related Behavior.

    Science.gov (United States)

    Lee, Jung-Ah; Sung, Yongjun

    2016-05-01

    While prior research has examined the relationship between narcissism and self-promoting behaviors on social media (e.g., posting selfies), little is known about the extent to which individuals' level of narcissism relates to how involved they are in other people's feedback (e.g., comments and "likes") received on their selfies, or how observant and responsive they are to other people's selfie postings. The present study investigates how narcissism relates to such selfie-related behaviors, as well as overall evaluation of selfie-posting behavior and intention to post selfies in the future. By employing a total of 315 Korean subjects who take and post selfies on social networking sites, the present study indicates that individuals higher in narcissism are more likely to evaluate selfie-posting behavior favorably, be involved in the feedback provided by others, and be observant of other people's selfies. However, level of narcissism did not moderate the relationship between how much one observes others' selfies and the likelihood of providing a comment or "like" on other people's selfies.

  8. Overt and Relational Aggression Participant Role Behavior: Measurement and Relations With Sociometric Status and Depression.

    Science.gov (United States)

    Casper, Deborah M; Card, Noel A; Bauman, Sheri; Toomey, Russell B

    2017-09-01

    This study is the first to measure participant role behavior across overt and relational forms of aggression. The Overt and Relational Aggression Participant Role Behavior Scales were designed to measure aggression, assisting, reinforcing, defending, victimization, and outsider behavior during acts of peer aggression in an ethnically diverse sample of 609 adolescents (M age = 12 years). The data fit the hypothesized 12-factor model, and measurement invariance was established across gender. Relational victimization, but not overt victimization, was positively associated with all other relational aggression roles. Each participant role subscale was positively associated with depressive symptoms with the exception of the overt and relational outsider subscales. Future research and intervention efforts should consider overt and relational aggression participant roles, separately. © 2017 The Authors. Journal of Research on Adolescence © 2017 Society for Research on Adolescence.

  9. Electrochemical Processes

    DEFF Research Database (Denmark)

    Bech-Nielsen, Gregers

    1997-01-01

    The notes describe in detail primary and secondary galvanic cells, fuel cells, electrochemical synthesis and electroplating processes, corrosion: measurments, inhibitors, cathodic and anodic protection, details of metal dissolution reactions, Pourbaix diagrams and purification of waste water from...

  10. Parents' perfectionism and its relation to child rearing behaviors.

    Science.gov (United States)

    Greblo, Zrinka; Bratko, Denis

    2014-04-01

    The aim of the study was to investigate the relationship between parents' perfectionism and self-reported parenting behaviors. The study included 786 parents (417 mothers and 369 fathers) of high school students. Results showed that parents' positive and negative perfectionism were differently related to specific forms of child rearing practices. Namely, positive perfectionism was positively, while negative perfectionism was negatively related to parental acceptance for both mothers and fathers. Mothers' and fathers' negative perfectionism was positively related to parental criticism and permissiveness. In addition, fathers' positive perfectionism was negatively associated with permissive child rearing practices. After controlling for background variables, parents' positive and negative perfectionism explained significant amounts of variance in all self-reported parenting dimensions for fathers and significantly accounted for the variance of parental acceptance and criticism for mothers. According to our findings, parents' perfectionism might have an important role in shaping parenting behaviors. © 2014 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

  11. Peer relations, adolescent behavior, and public health research and practice.

    Science.gov (United States)

    Crosnoe, Robert; McNeely, Clea

    2008-01-01

    Peer relations are central to adolescent life and, therefore, are crucial to understanding adolescents' engagement in various behaviors. In recent years, public health research has increasingly devoted attention to the implications of peer relations for the kinds of adolescent behaviors that have a direct impact on health. This article advocates for a continuation of this trend. With this aim, we highlight key themes in the rich literature on the general developmental significance of adolescent-peer relations, provide an overview of how these themes have been incorporated into public health research and practice, and suggest future avenues for peer-focused public health research that can inform adolescent health promotion in the United States.

  12. The Behavioral Pharmacology of Effort-related Choice Behavior: Dopamine, Adenosine and Beyond

    Science.gov (United States)

    Salamone, John D; Correa, Merce; Nunes, Eric J; Randall, Patrick A; Pardo, Marta

    2012-01-01

    For many years, it has been suggested that drugs that interfere with dopamine (DA) transmission alter the “rewarding” impact of primary reinforcers such as food. Research and theory related to the functions of mesolimbic DA are undergoing a substantial conceptual restructuring, with the traditional emphasis on hedonia and primary reward yielding to other concepts and lines of inquiry. The present review is focused upon the involvement of nucleus accumbens DA in effort-related choice behavior. Viewed from the framework of behavioral economics, the effects of accumbens DA depletions and antagonism on food-reinforced behavior are highly dependent upon the work requirements of the instrumental task, and DA-depleted rats show a heightened sensitivity to response costs, especially ratio requirements. Moreover, interference with accumbens DA transmission exerts a powerful influence over effort-related choice behavior. Rats with accumbens DA depletions or antagonism reallocate their instrumental behavior away from food-reinforced tasks that have high response requirements, and show increased selection of low reinforcement/low cost options. Nucleus accumbens DA and adenosine interact in the regulation of effort-related functions, and other brain structures (anterior cingulate cortex, amygdala, ventral pallidum) also are involved. Studies of the brain systems regulating effort-based processes may have implications for understanding drug abuse, as well as symptoms such as psychomotor slowing, fatigue or anergia in depression and other neurological disorders. PMID:22287808

  13. Electrochemical corrosion behavior of composite MAO/sol-gel coatings on magnesium alloy AZ91D using combined micro-arc oxidation and sol-gel technique

    International Nuclear Information System (INIS)

    Shang Wei; Chen Baizhen; Shi Xichang; Chen Ya; Xiao Xiang

    2009-01-01

    Protective composite coatings were obtained on a magnesium alloy by micro-arc oxidation (MAO) and sol-gel technique. The coatings consisted of a MAO layer and a sol-gel layer. The microstructure and composition of the MAO coating and the composite coatings were analyzed by scanning electron microscopy (SEM) and energy dispersive X-rays (EDX). Potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and total immersion tests were used to evaluate the corrosion behavior of these coatings in a 3.5 wt.% NaCl solution. The results show that the sol-gel layer provides corrosion protection by physically sealing the pores in the MAO coating and acting as a barrier. The composite coatings can suppress the corrosion process by preventing the corrosive ions from transferring or diffusing to the magnesium alloy substrate. This enhances the corrosion resistance of the magnesium alloy AZ91D significantly

  14. Facile polyol synthesis of CoFe2O4 nanosphere clusters and investigation of their electrochemical behavior in different aqueous electrolytes

    Science.gov (United States)

    Malaie, K.; Ganjali, M. R.; Alizadeh, T.; Norouzi, P.

    2018-04-01

    CoFe2O4 nanosphere clusters (CFNCs) with good crystallinity were synthesized through a facile polyol process without using any surfactant or template. FESEM images show cobalt ferrite clusters with a diameter of 200-400 nm with nanospheres grown on the surface. The electrochemical behavior of the CFNCs was investigated in different electrolytes of KOH, K2SO4, and Na2SO3 in the negative potential window of - 0.3 to - 1.3 V for possible application in supercapacitor electrodes. CFNCs exhibited best performance in KOH electrolyte with a specific capacitance of 151 F g-1 in 5 mV s-1 and a cycling stability of 87% over 1000 voltammetric cycles. These studies indicate the potential application of the as-obtained CFNCs as negative electrodes in alkaline supercapacitors.

  15. Electrochemical analysis

    International Nuclear Information System (INIS)

    Hwang, Hun

    2007-02-01

    This book explains potentiometry, voltametry, amperometry and basic conception of conductometry with eleven chapters. It gives the specific descriptions on electrochemical cell and its mode, basic conception of electrochemical analysis on oxidation-reduction reaction, standard electrode potential, formal potential, faradaic current and faradaic process, mass transfer and overvoltage, potentiometry and indirect potentiometry, polarography with TAST, normal pulse and deferential pulse, voltammetry, conductometry and conductometric titration.

  16. Perceived Sexual Control, Sex-Related Alcohol Expectancies and Behavior Predict Substance-Related Sexual Revictimization

    Science.gov (United States)

    Walsh, Kate; Messman-Moore, Terri; Zerubavel, Noga; Chandley, Rachel B.; DeNardi, Kathleen A.; Walker, Dave P.

    2013-01-01

    Objectives Although numerous studies have documented linkages between childhood sexual abuse (CSA) and later sexual revictimization, mechanisms underlying revictimization, particularly assaults occurring in the context of substance use, are not well-understood. Consistent with Traumagenic Dynamics theory, the present study tested a path model positing that lowered perceptions of sexual control resulting from CSA may be associated with increased sex-related alcohol expectancies and heightened likelihood of risky sexual behavior, which in turn, may predict adult substance-related rape. Methods Participants were 546 female college students who completed anonymous surveys regarding CSA and adult rape, perceptions of sexual control, sex-related alcohol expectancies, and likelihood of engaging in risky sexual behavior. Results The data fit the hypothesized model well and all hypothesized path coefficients were significant and in the expected directions. As expected, sex-related alcohol expectancies and likelihood of risky sexual behavior only predicted substance-related rape, not forcible rape. Conclusions Findings suggested that low perceived sexual control stemming from CSA is associated with increased sex-related alcohol expectancies and a higher likelihood of engaging in sexual behavior in the context of alcohol use. In turn these proximal risk factors heighten vulnerability to substance-related rape. Programs which aim to reduce risk for substance-related rape could be improved by addressing expectancies and motivations for risky sexual behavior in the context of substance use. Implications and future directions are discussed. PMID:23312991

  17. Sex-related variation in human behavior and the brain

    Science.gov (United States)

    Hines, Melissa

    2010-01-01

    Male and female fetuses differ in testosterone concentrations beginning as early as week 8 of gestation. This early hormone difference exerts permanent influences on brain development and behavior. Contemporary research shows that hormones are particularly important for the development of sex-typical childhood behavior, including toy choices, which until recently were thought to result solely from sociocultural influences. Prenatal testosterone exposure also appears to influence sexual orientation and gender identity, as well as some, but not all, sex-related cognitive, motor and personality characteristics. Neural mechanisms responsible for these hormone-induced behavioral outcomes are beginning to be identified, and current evidence suggests involvement of the hypothalamus and amygdala, as well as interhemispheric connectivity, and cortical areas involved in visual processing. PMID:20724210

  18. Health behaviors and work-related outcomes among school employees.

    Science.gov (United States)

    LeCheminant, James D; Merrill, Ray M; Masterson, Travis

    2015-05-01

    To determine the association between selected health behaviors and work-related outcomes among 2398 school-based employees who voluntarily enrolled in a worksite wellness program. This study presents participants' baseline data collected from a personal health assessment used by Well-Steps, a third-party wellness company. Employees with high levels of exercise, fruit/vegetable consumption, or restful sleep exhibited higher job-performance and job-satisfaction, and lower absenteeism (p job-performance (Prevalence Ratio=1.09; 95% CI=1.05-1.13), job-satisfaction (Prevalence Ratio=1.53; 95% CI=1.30-1.80), and lower absenteeism (Prevalence Ratio=1.16; 95% CI=1.08-1.325). Further, number of co-occurring health behaviors influenced other satisfaction and emotional health outcomes. Selected healthy behaviors, individually or co-occurring, are associated with health outcomes potentially important at the worksite.

  19. Social relationships and health related behaviors among older US adults.

    Science.gov (United States)

    Watt, Richard G; Heilmann, Anja; Sabbah, Wael; Newton, Tim; Chandola, Tarani; Aida, Jun; Sheiham, Aubrey; Marmot, Michael; Kawachi, Ichiro; Tsakos, Georgios

    2014-05-30

    Health behaviors are a key determinant of health and well-being that are influenced by the nature of the social environment. This study examined associations between social relationships and health-related behaviors among a nationally representative sample of older people. We analyzed data from three waves (1999-2004) of the US National Health and Nutrition Examination Survey (NHANES). Participants were 4,014 older Americans aged 60 and over. Log-binomial regression models estimated prevalence ratios (PR) for the associations between social relationships and each of the following health behaviors: alcohol use, smoking, physical activity and dental attendance. Health-compromising behaviors (smoking, heavy drinking and less frequent dental visits) were related to marital status, while physical activity, a health-promoting behavior, was associated with the size of friendship networks. Smoking was more common among divorced/separated (PR = 2.1; 95% CI: 1.6, 2.7) and widowed (PR = 1.7; 95% CI: 1.3, 2.3) respondents than among those married or cohabiting, after adjusting for socio-demographic background. Heavy drinking was 2.6 times more common among divorced/separated and 1.7 times more common among widowed men compared to married/cohabiting men, while there was no such association among women. For women, heavy drinking was associated with being single (PR = 1.7; 95% CI: 1.0, 2.9). Being widowed was related to a lower prevalence of having visited a dentist compared to being married or living with a partner (PR = 0.92; 95% CI 0.86, 0.99). Those with a larger circle of friends were more likely to be physically active (PR = 1.17; 95% CI:1.06, 1.28 for 5-8 versus less than 5 friends). Social relationships of older Americans were independently associated with different health-related behaviors, even after adjusting for demographic and socioeconomic determinants. Availability of emotional support did not however mediate these associations. More research is

  20. Effect of small addition of aluminum on electrochemical corrosion behavior of magnesium-calcium sacrificial anode in underground environment

    International Nuclear Information System (INIS)

    Rizam, S.S.; Sasirehka, G.; Firdaus, A.M.H.; Mahdi, C.I.; Nazree, D.M.; Abdul Razak Daud; Azrem, A.A.

    2009-01-01

    The effect of small addition of Al on the electrochemical performances was investigated by open circuit potential and Tafel Extrapolation method. The results show that open circuit potential reveals as-cast Mg containing Ca alloys with minor content of Al maintained highly negative potential with the range of -1.68 to -1.63 V SCE in comparison to both pure Mg (-1.60V SCE ) and commercial high potential Mg content. Corrosion rate for the as-cast samples remains higher (30-17 mpy) than pure Mg (3 mpy) and commercial high potential Mg anode (14 mpy). The increasing small content of Al results in the reduction of corrosion rate significantly. Therefore, it proves that the performance of Mg containing Ca alloy is strongly influenced by the concentration of Al. (author)

  1. Electrochemical behavior and stability of a commercial activated carbon in various organic electrolyte combinations containing Li-salts

    International Nuclear Information System (INIS)

    Zhang, Tong; Fuchs, Bettina; Secchiaroli, Marco; Wohlfahrt-Mehrens, Margret; Dsoke, Sonia

    2016-01-01

    Highlights: • 1 M LiPF 6 in PC displays the widest electrochemical stability window among others couples electrolyte/activated carbon. • Electrolytes based on EC-DMC show lower impedance than electrolytes containing PC. • 1 M LiPF 6 in PC has the highest cycling stability with 75% of capacitance retention after 20 000 cycles. - Abstract: The fast development of Li-ion capacitor (LIC) technologies requires the use of low resistance and stable electrolytes. An electrolyte for a LIC not only has to provide Li for the intercalation/deintercalation of the battery-type materials, but it also needs to be compatible with the supercapacitor material. Before designing a hybrid Li-ion capacitor device containing Li-insertion and double layer-type materials, it is necessary to understand and separate the contribution of each electrode material to the resistance, capacity and stability in the chosen electrolyte. Due to the intensive research on Li-ion batteries, the interactions of Li-salt containing electrolytes combined with Li insertion materials have been extensively investigated, and a lot of literature is available on this field. In contrast, there is only little knowledge about the exclusive interaction and compatibility of Li containing electrolytes with supercapacitor-type electrode materials (in absence of battery materials). With this purpose, this paper explores the electrochemical performance of electrodes based on commercial activated carbon (AC) in various lithium salt-containing electrolytes. A standard electrolyte for Li-ion batteries (1 M LiPF 6 in EC:DMC, 1:1) is evaluated and compared with an electrolyte prepared with the same salt dissolved in propylene carbonate (1 M LiPF 6 in PC) which is a solvent typically used in commercial supercapacitors. Furthermore, two new electrolyte solutions are proposed, based on a blend of salts 0.8 M LiPF 6 + 0.2 M NEt 4 BF 4 in EC:DMC (1:1) as well as in pure PC. The effect of the electrolyte composition is evaluated

  2. Nutrition Facts Use in Relation to Eating Behaviors and Healthy and Unhealthy Weight Control Behaviors.

    Science.gov (United States)

    Christoph, Mary J; Loth, Katie A; Eisenberg, Marla E; Haynos, Ann F; Larson, Nicole; Neumark-Sztainer, Dianne

    2018-03-01

    Investigate the relationship between use of Nutrition Facts labels on packaged foods and weight-related behaviors. Cross-sectional survey in 2015-2016. Young adult respondents (n = 1,817; 57% women; average age 31.0 ± 1.6 years) to the Project Eating and Activity in Teens and Young Adults-IV survey, the fourth wave of a longitudinal cohort study. Use of Nutrition Facts labels on packaged foods; healthy, unhealthy, and extreme weight control behaviors; intuitive eating; binge eating. Linear and logistic regression models were adjusted for age, ethnicity/race, education, income, and weight status. In women, greater Nutrition Facts use was associated with a 23% and 10% greater likelihood of engaging in healthy and unhealthy weight control behaviors, respectively, and a 17% greater chance of engaging in binge eating. In men, greater label use was associated with a 27% and 17% greater likelihood of engaging in healthy and unhealthy weight control behaviors, respectively, and a lower level of intuitive eating. Professionals advising patients and clients on weight management may consider possible gender differences in response to weight loss and management guidance. Since label use was related to engagement in some unhealthy behaviors in addition to healthy behaviors, it is important to consider how individuals may use labels, particularly those at risk for, or engaging in, disordered eating behaviors. Future research investigating potential relationships between Nutrition Facts use, intuitive eating, and binge eating is needed. Copyright © 2017 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

  3. Mixed-Metal, Structural, and Substitution Effects of Polyoxometalates on Electrochemical Behavior in a Redox Flow Battery

    International Nuclear Information System (INIS)

    Pratt, Harry D.; Pratt, William R.; Fang, Xikui; Hudak, Nicholas S.; Anderson, Travis M.

    2014-01-01

    Graphical abstract: - Highlights: • Testing of a flow battery with polyoxometalates. • Coulombic efficiency of 83% for an iron-based compound. • Both size and charge density influence battery performance. - Abstract: A pair of redox flow batteries containing polyoxometalates was tested as part of an ongoing program in stationary energy storage. The iron-containing dimer, (SiFe 3 W 9 (OH) 3 O 34 ) 2 (OH) 3 11− , cycled between (SiFe 3 W 9 (OH) 3 O 34 ) 2 (OH) 3 11− /(SiFe 3 W 9 (OH) 3 O 34 ) 2 (OH) 3 14− and (SiFe 3 W 9 (OH) 3 O 34 ) 2 (OH) 3 17− /(SiFe 3 W 9 (OH) 3 O 34 ) 2 (OH) 3 14− for the positive and negative electrode, respectively. This compound demonstrated a coulombic efficiency of 83% after 20 cycles with an electrochemical yield (measured discharge capacity as a percentage of theoretical capacity) of 55%. Cyclic voltammetry on the Lindqvist ion, cis-V 2 W 4 O 19 4− , showed quasi-reversible vanadium electrochemistry, but tungsten reduction was mostly irreversible. In a flow cell configuration, cis-V 2 W 4 O 19 4− had a coulombic efficiency of 45% (for a two-electron process) and an electrochemical yield of 16% after 20 cycles. The poor performance of cis-V 2 W 4 O 19 4− was attributed primarily to its higher charge density. Collectively, the results showed that both polyoxometalate size and charge density are both important parameters to consider in battery material performance

  4. Aging Men’s Health-Related Behaviors

    Directory of Open Access Journals (Sweden)

    Terry Peak

    2014-11-01

    Full Text Available This conceptual review summarizes the current research on older men and their health-related behaviors with special attention given to the influence of the hegemonic masculinity framework over the life span. The authors consider whether masculinity precepts can be modified to enable men to alter their gendered morbidity/mortality factors and achieve healthier and longer lives. Also included is an overview of the gender-based research and health education efforts to persuade men to adopt more effective health-related behaviors or health practices earlier in the life span. Given the current attention being paid to men’s health, for example, their higher risk of morbidity and mortality both generally and at younger ages, and the associated health care costs tied to those risks, the ethical and economic implications of this review may prove useful.

  5. Autism-related behavioral abnormalities in synapsin knockout mice.

    Science.gov (United States)

    Greco, Barbara; Managò, Francesca; Tucci, Valter; Kao, Hung-Teh; Valtorta, Flavia; Benfenati, Fabio

    2013-08-15

    Several synaptic genes predisposing to autism-spectrum disorder (ASD) have been identified. Nonsense and missense mutations in the SYN1 gene encoding for Synapsin I have been identified in families segregating for idiopathic epilepsy and ASD and genetic mapping analyses have identified variations in the SYN2 gene as significantly contributing to epilepsy predisposition. Synapsins (Syn I/II/III) are a multigene family of synaptic vesicle-associated phosphoproteins playing multiple roles in synaptic development, transmission and plasticity. Lack of SynI and/or SynII triggers a strong epileptic phenotype in mice associated with mild cognitive impairments that are also present in the non-epileptic SynIII(-/-) mice. SynII(-/-) and SynIII(-/-) mice also display schizophrenia-like traits, suggesting that Syns could be involved in the regulation of social behavior. Here, we studied social interaction and novelty, social recognition and social dominance, social transmission of food preference and social memory in groups of male SynI(-/-), SynII(-/-) and SynIII(-/-) mice before and after the appearance of the epileptic phenotype and compared their performances with control mice. We found that deletion of Syn isoforms widely impairs social behaviors and repetitive behaviors, resulting in ASD-related phenotypes. SynI or SynIII deletion altered social behavior, whereas SynII deletion extensively impaired various aspects of social behavior and memory, altered exploration of a novel environment and increased self-grooming. Social impairments of SynI(-/-) and SynII(-/-) mice were evident also before the onset of seizures. The results demonstrate an involvement of Syns in generation of the behavioral traits of ASD and identify Syn knockout mice as a useful experimental model of ASD and epilepsy. Copyright © 2013 Elsevier B.V. All rights reserved.

  6. Explaining reported puma-related behaviors and behavioral intentions among northern Arizona residents

    Science.gov (United States)

    Mattson, David J.; Ruther, Elizabeth J.

    2012-01-01

    Management of pumas in the American West is typified by conflict among stakeholders plausibly rooted in life experiences and worldviews. We used a mail questionnaire to assess demographics, nature-views, puma-related life experiences and behaviors, and support for puma-related policies among residents of northern Arizona. Data from the questionnaire (n = 693 respondents) were used to model behaviors and support for policies. Compared to models based on nature-views and life experiences, those based on demographics had virtually no support from the data. The Utilitarian/Dominionistic nature-view had the strongest effect of any variable in six of seven models, and was associated with firearms and opposition to policies that would limit killing pumas. The Humanistic/Moralistic nature-view was positively associated with non-lethal behaviors and policies in five models. Gender had the strongest effect of any demographic variable. Compared to demographics alone, our results suggest that worldviews provide a more meaningful explanation of reported human behaviors and behavioral intentions regarding pumas.

  7. Measuring the relative importance of strategic thinking dimensions in relation to counterproductive behavior

    Directory of Open Access Journals (Sweden)

    Afsaneh Zamani Moghaddam

    2013-11-01

    Full Text Available The purpose of this paper is to explore the relative importance of strategic thinking dimensions in prediction of counter-productive behavior. The research method is based on a descriptive- Survey research. After collecting the questionnaires from 73 top managers and 110 staffs, the correlations between strategic thinking dimensions and counterproductive behavior were calculated. The relative importance method was used to calculate the relative weight of each dimension of strategic thinking in prediction of counterproductive behaviors. The results show that the strategic thinking of top managers is associated with their counterproductive behavior (correlation coefficient -0.38. Furthermore, The results of the Relative Importance Method indicate that the relative importance of each dimension of strategic thinking in prediction of counterproductive behavior is not the same. System perspective with 31.1% has the highest importance and hypothesis driven with 11.7% has the lowest weight. Intent focus, thinking in time and intelligent opportunism predict 14.1%, 13.3%, and 29.8% of counter-productive changes, respectively.

  8. Service Encounter Related Process Quality, Patient Satisfaction, and Behavioral Intention

    Directory of Open Access Journals (Sweden)

    Nandakumar Mekoth

    2011-12-01

    Full Text Available This study identifies some of the critical service encounters thatthe outpatients undergo in a health care facility and investigateswhether the service encounter related process quality as perceivedby the patients leads to patient satisfaction, repeat visit, and recommendationintentions. Personal visits, observations, and enquiriesat the outpatient center have been conducted to identifythe various service encounters that outpatients undergo in thehospital. Exit interviews of the outpatients have been conductedto identify service encounter related process quality variableswhich determine patient satisfaction and behavioral intentions.A preliminary scale to measure service encounter related processquality was developed and its factor structure and internal consistencyreliability were established. The study reveals that boththe physician quality and laboratory quality have been found tobe significantly related to patient satisfaction. However, quite interestingly,courtesy shown by the registration or outpatient staff,perceived length of waiting time, or even the salient aspects of theservicescape, did not influence patient satisfaction.

  9. Preparation of three-dimensional nitrogen-doped graphene layers by gas foaming method and its electrochemical capactive behavior

    International Nuclear Information System (INIS)

    Hao, Junnan; Shu, Dong; Guo, Songtao; Gao, Aimei; He, Chun; Zhong, Yayun; Liao, Yuqing; Huang, Yulan; Zhong, Jie

    2016-01-01

    Highlights: • A three-dimensional porous graphene layers was prepared via a gas foaming method. • Melamine was the nitrogen source to synthesize the N-doped 3D graphene layers. • The specific surface area of 3D N-doped graphene material is as high as 1196 m 2 g −1 . • The 3D N-doped graphene specific capacitance is 335 F g −1 in three-electrode system. • The energy density of 3D N-doped graphene reaches 58.1 Wh kg −1 in a symmetric cell. - Abstract: A porous graphene layers with a three-dimensional structure (3DG) was prepared via a gas foaming method based on a polymeric predecessor. This intimately interconnected 3DG structure not only significantly increases the specific surface area but also provides more channels to facilitate electron transport. In addition, 3D N-doped (3DNG) layers materials were synthesized using melamine as a nitrogen source. The nitrogen content in the 3DNG layers significantly influenced the electrochemical performance. The sample denoted as 3DNG-2 exhibited a specific capacitance of 335.2 F g −1 at a current density of 1 A g −1 in a three-electrode system. Additionally, 3DNG-2 exhibited excellent electrochemical performance in aqueous and organic electrolytes using a two-electrode symmetric cell. An energy density of 58.1 Wh kg −1 at a power density of 2500 W kg −1 was achieved, which is approximately 3 times that (19.6 Wh kg −1 ) in an aqueous electrolyte in a two-electrode system. After 1000 cycles, the capacity retention in aqueous electrolyte was more than 99.0%, and this retention in organic electrolytes was more than 89.4%, which demonstrated its excellent cycle stability. This performance makes 3DNG-2 a promising candidate as an electrode material in high-power and high-energy supercapacitor applications.

  10. Electrochemical behavior of Ni{sub x}W{sub 1-x} materials as catalyst for hydrogen evolution reaction in alkaline media

    Energy Technology Data Exchange (ETDEWEB)

    Oliver-Tolentino, Miguel A. [UPIBI-IPN, Departamento de Ciencias Basicas, Av. Acueducto s/n, Barrio La Laguna, Col. Ticoman, Mexico D.F. 07340 (Mexico); Arce-Estrada, Elsa M. [ESIQIE-IPN Departamento de Ingenieria en Metalurgia y Materiales, UPALM, UPALM, Mexico D.F. 07738 (Mexico); Cortes-Escobedo, Claudia A. [Centro de Investigacion e Innovacion Tecnologica del IPN, Cda. Cecati s/n, Col. Sta. Catarina, CP 02250 Azcapotzalco D.F. (Mexico); Bolarin-Miro, Ana M.; Sanchez-De Jesus, Felix [Area Academica de Ciencias de la Tierra y Materiales, Universidad Autonoma del Estado de Hidalgo, CU, Carr. Pachuca-Tulancingo Km. 4.5, Mineral de la Reforma, CP 42184 Hidalgo (Mexico); Gonzalez-Huerta, Rosa de G. [ESIQIE-IPN, Departamento de Ingenieria Quimica - Laboratorio de Electroquimica y Corrosion, Edif. Z-5 3er piso, UPALM, Mexico D.F. 07738 (Mexico); Manzo-Robledo, Arturo, E-mail: amanzor@ipn.mx [ESIQIE-IPN, Departamento de Ingenieria Quimica - Laboratorio de Electroquimica y Corrosion, Edif. Z-5 3er piso, UPALM, Mexico D.F. 07738 (Mexico)

    2012-09-25

    Highlights: Black-Right-Pointing-Pointer The electrochemical techniques used in this study elucidated the Ni-W surface state. Black-Right-Pointing-Pointer The Ni-W materials were effective for the hydrogen evolution reaction. Black-Right-Pointing-Pointer The prepared alloys exhibited higher catalytic activity than their precursors. Black-Right-Pointing-Pointer The preparation method is relatively simple and effective procedure. - Abstract: In the present work, results of electrochemical evaluation, as well as morphological and structural characterization of Ni{sub x}W{sub 1-x} materials with x = 0.77, 0.64, 0.4, 0.19 and 0.07 processed by means of high energy ball milling from high purity powders are presented. Also, the electrocatalytic performance on the hydrogen evolution reaction (HER) of the Ni{sub x}W{sub 1-x} materials evaluated by linear polarization and cyclic voltammetry techniques in alkaline media at room temperature is discussed. The structural and morphological characterization of the as-prepared materials was carried out using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results indicated a small-particle clusters and solid solution formation. According to the kinetics parameters the best electrocatalytic activity was observed at Ni{sub 64}W{sub 36}.

  11. Event-related potentials, cognition, and behavior: a biological approach.

    Science.gov (United States)

    Kotchoubey, Boris

    2006-01-01

    The prevailing cognitive-psychological accounts of event-related brain potentials (ERPs) assume that ERP components manifest information processing operations leading from stimulus to response. Since this view encounters numerous difficulties already analyzed in previous studies, an alternative view is presented here that regards cortical control of behavior as a repetitive sensorimotor cycle consisting of two phases: (i) feedforward anticipation and (ii) feedback cortical performance. This view allows us to interpret in an integrative manner numerous data obtained from very different domains of ERP studies: from biophysics of ERP waves to their relationship to the processing of language, in which verbal behavior is viewed as likewise controlled by the same two basic control processes: feedforward (hypothesis building) and feedback (hypothesis checking). The proposed approach is intentionally simplified, explaining numerous effects on the basis of few assumptions and relating several levels of analysis: neurophysiology, macroelectrical processes (i.e. ERPs), cognition and behavior. It can, therefore, be regarded as a first approximation to a general theory of ERPs.

  12. Use of Local Electrochemical Methods (SECM, EC-STM) and AFM to Differentiate Microstructural Effects (EBSD) on Very Pure Copper

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Lombardia, Esther; Graeve, Iris De; Terryn, Herman [Vrije Universiteit Brussel, Brussels (Belgium); Lapeire, Linsey; Verbeken, Kim; Kestens, Leo [Ghent University, Zwijnaarde (Ghent) (Belgium); Maurice, Vincent; Klein, Lorena; Marcus, Philippe [Institut de Recherche de Chimie Paris, Paris (France); Gonzalez-Garcia, Yaiza; Mol, Arjan [Delft University of Technology, Delft (Netherlands)

    2017-02-15

    When aiming for an increased and more sustainable use of metals a thorough knowledge of the corrosion phenomenon as function of the local metal microstructure is of crucial importance. In this work, we summarize the information presented in our previous publications and present an overview of the different local (electrochemical) techniques that have been proven to be effective in studying the relation between different microstructural variables and their different electrochemical behavior. Atomic force microscopy (AFM), scanning electrochemical microscopy (SECM), and electrochemical scanning tunneling microscopy (EC-STM) were used in combination with electron backscatter diffraction (EBSD). Consequently, correlations could be identified between the grain orientation and grain boundary characteristics, on the one hand, and the electrochemical behavior on the other hand. The grain orientation itself has an influence on the corrosion, and the orientation of the neighboring grains also seems to play a decisive role in the dissolution rate. With respect to intergranular corrosion, only coherent twin boundaries seem to be resistant.

  13. Bioactivity and electrochemical behavior of hydroxyapatite-silicon-multi walled carbon nano-tubes composite coatings synthesized by EPD on NiTi alloys in simulated body fluid

    Energy Technology Data Exchange (ETDEWEB)

    Khalili, V., E-mail: V_khalili@sut.ac.ir [Department of Materials Engineering, Engineering Faculty, University of Bonab, Bonab (Iran, Islamic Republic of); Khalil-Allafi, J. [Research Center for Advanced Materials and Mineral Processing, Faculty of Materials Engineering, Sahand University of Technology, Tabriz (Iran, Islamic Republic of); Frenzel, J.; Eggeler, G. [Institute for Materials, Faculty of Mechanical Engineering, Ruhr-University Bochum, 44801 Bochum (Germany)

    2017-02-01

    In order to improve the surface bioactivity of NiTi bone implant and corrosion resistance, hydroxyapatite coating with addition of 20 wt% silicon, 1 wt% multi walled carbon nano-tubes and both of them were deposited on a NiTi substrate using a cathodic electrophoretic method. The apatite formation ability was estimated using immersion test in the simulated body fluid for 10 days. The SEM images of the surface of coatings after immersion in simulated body fluid show that the presence of silicon in the hydroxyapatite coatings accelerates in vitro growth of apatite layer on the coatings. The Open-circuit potential and electrochemical impedance spectroscopy were measured to evaluate the electrochemical behavior of the coatings in the simulated body fluid at 37 °C. The results indicate that the compact structure of hydroxyapatite-20 wt% silicon and hydroxyapatite-20 wt% silicon-1 wt% multi walled carbon nano-tubes coatings could efficiently increase the corrosion resistance of NiTi substrate. - Highlights: • The composite coatings of HA, Si and MWCNTs was prepared using electrophoretic deposition. • The presence of 1 wt.% MWCNTs in the HA coating provides more nucleation cites of apatite crystallites in SBF. • The presence of Si in HA coating increases the growth rate of apatite crystallites with the Ca/P atomic ratio of 1.67. • The EIS indicate the compact HA-20%Si and HA-20%Si-1%MWCNTs coatings efficiently increase corrosion resistance of NiTi. • The porous HA and HA-1%MWCNTs do not increase significantly corrosion resistance due to the easy diffusion path.

  14. Body-related self-conscious emotions relate to physical activity motivation and behavior in men.

    Science.gov (United States)

    Castonguay, Andree L; Pila, Eva; Wrosch, Carsten; Sabiston, Catherine M

    2015-05-01

    The aim of this study was to examine the associations between the body-related self-conscious emotions of shame, guilt, and pride and physical activity motivation and behavior among adult males. Specifically, motivation regulations (external, introjected, indentified, intrinsic) were examined as possible mediators between each of the body-related self-conscious emotions and physical activity behavior. A cross-sectional study was conducted with adult men (N = 152; Mage = 23.72, SD = 10.92 years). Participants completed a questionnaire assessing body-related shame, guilt, authentic pride, hubristic pride, motivational regulations, and leisure-time physical activity. In separate multiple mediation models, body-related shame was positively associated with external and introjected regulations and negatively correlated with intrinsic regulation. Guilt was positively linked to external, introjected, and identified regulations. Authentic pride was negatively related to external regulation and positively correlated with both identified and intrinsic regulations and directly associated with physical activity behavior. Hubristic pride was positively associated with intrinsic regulation. Overall, there were both direct and indirect effects via motivation regulations between body-related self-conscious emotions and physical activity (R(2) shame = .15, guilt = .16, authentic pride = .18, hubristic pride = .16). These findings highlight the importance of targeting and understanding self-conscious emotions contextualized to the body and links to motivation and positive health behavior among men. © The Author(s) 2014.

  15. Adolescents' perception of peer groups: Psychological, behavioral, and relational determinants.

    Science.gov (United States)

    Lee, Seungyoon; Foote, Jeremy; Wittrock, Zachary; Xu, Siyu; Niu, Li; French, Doran C

    2017-07-01

    Adolescents' social cognitive understanding of their social world is often inaccurate and biased. Focusing on peer groups, this study examines how adolescents' psychological, behavioral, and relational characteristics influence the extent to which they accurately identify their own and others' peer groups. Analyses were conducted with a sample of 1481 seventh- and tenth-grade Chinese students who are embedded with 346 peer groups. Overall, females and older students had more accurate perceptions. In addition, lower self-esteem, higher indegree centrality, and lower betweenness centrality in the friendship network predicted more accurate perception of one's own groups, whereas higher academic performance and lower betweenness centrality in the friendship network predicted more accurate perception of others' groups. Implications for understanding the connection between adolescents' psychological and behavioral traits, social relationships, and social cognition are discussed. Copyright © 2016 Elsevier Inc. All rights reserved.

  16. Determinants of consumer behavior related to organic foods.

    Science.gov (United States)

    Shepherd, Richard; Magnusson, Maria; Sjödén, Per-Olow

    2005-06-01

    There have been many studies of what influences consumers in their decisions to purchase or consume organic foods, mainly concerned with fresh organic foods. These show a discrepancy between attitudes and behavior with people being positive about organic foods but often not purchasing them. This discrepancy seems to be explained by the fact that consumers do not consider "organically produced" to be an important purchase criterion, that organic foods are not perceived to surpass conventional foods regarding taste and shelf life (two qualities rated to be of great importance), and because of the perceived premium prices of organic foods. In two Swedish studies, health benefits were demonstrated to be more strongly related to attitudes and behavior toward organic foods than were perceived environmental benefits. A new European Union (EU) project will investigate the influences on both fresh and processed organic foods and investigate the role of moral, ethical, and affective influences on choice across eight EU countries.

  17. Endocrine Disruption of Vasopressin Systems and Related Behaviors

    Directory of Open Access Journals (Sweden)

    Heather B. Patisaul

    2017-06-01

    Full Text Available Endocrine disrupting chemicals (EDCs are chemicals that interfere with the organizational or activational effects of hormones. Although the vast majority of the EDC literature focuses on steroid hormone signaling related impacts, growing evidence from a myriad of species reveals that the nonapeptide hormones vasopressin (AVP and oxytocin (OT may also be EDC targets. EDCs shown to alter pathways and behaviors coordinated by AVP and/or OT include the plastics component bisphenol A (BPA, the soy phytoestrogen genistein (GEN, and various flame retardants. Many effects are sex specific and likely involve action at nuclear estrogen receptors. Effects include the elimination or reversal of well-characterized sexually dimorphic aspects of the AVP system, including innervation of the lateral septum and other brain regions critical for social and other non-reproductive behaviors. Disruption of magnocellular AVP function has also been reported in rats, suggesting possible effects on hemodynamics and cardiovascular function.

  18. Electrochemical and anticorrosion behaviors of hybrid functionalized graphite nano-platelets/tripolyphosphate in epoxy-coated carbon steel

    International Nuclear Information System (INIS)

    Mohammadi, Somayeh; Shariatpanahi, Homeira; Taromi, Faramarz Afshar; Neshati, Jaber

    2016-01-01

    Highlights: • FGNP was combined with TPP to obtain a hybrid nano-particle. • TEM image showed uniform distribution of the hybrid nanoparticles in epoxy coating. • FGNP is a substrate for linking of TPP anions by hydrogen bonding. • FGNP as an accelerator, provides rapid iron phosphate passive film formation. • The hybrid nano-particle can provide long-term corrosion protection. - Abstract: Functionalized graphite nano-platelets (FGNP) were combined with tripolyphosphate (TPP) to gain a hybrid nano-particle (FGNP-TPP) with homogenous dispersion in epoxy, resulting in an excellent anti-corrosion coating for carbon steel substrate. Characterization analyses of the hybrid nano-particle were performed by FT-IR, SEM, XRD and TEM. TPP was linked to FGNP nano-particles by hydrogen bondings. Different epoxy coatings formulated with 1 wt.% of FGNP, FGNP-TPP and TPP were evaluated. Electrochemical investigations, salt spray and pull-off tests showed that the hybrid nano-particle can provide long-term corrosion protection compared to FGNP and TPP due to synergistic effect between FGNP as an accelerator and TPP as a corrosion inhibitor to produce a uniform and stable iron-phosphate passive film with high surface coverage.

  19. Electrochemical Behavior and Determination of Chlorogenic Acid Based on Multi-Walled Carbon Nanotubes Modified Screen-Printed Electrode

    Directory of Open Access Journals (Sweden)

    Xiaoyan Ma

    2016-10-01

    Full Text Available In this paper, the multi-walled carbon nanotubes modified screen-printed electrode (MWCNTs/SPE was prepared and the MWCNTs/SPE was employed for the electrochemical determination of the antioxidant substance chlorogenic acids (CGAs. A pair of well-defined redox peaks of CGA was observed at the MWCNTs/SPE in 0.10 mol/L acetic acid-sodium acetate buffer (pH 6.2 and the electrode process was adsorption-controlled. Cyclic voltammetry (CV and differential pulse voltammetry (DPV methods for the determination of CGA were proposed based on the MWCNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 0.17 to 15.8 µg/mL, and the linear regression equation was Ipa (µA = 4.1993 C (×10−5 mol/L + 1.1039 (r = 0.9976 and the detection limit for CGA could reach 0.12 µg/mL. The recovery of matrine was 94.74%–106.65% (RSD = 2.92% in coffee beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

  20. Electrochemical behavior of ruthenium-hexacyanoferrate modified glassy carbon electrode and catalytic activity towards ethanol electro oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Wendell M.; Marques, Aldalea L.B., E-mail: aldalea.ufma@hotmail.com [Universidade Federal do Maranhao (UFMA), Sao Luis, MA (Brazil). Departamento de Quimica Tecnologica; Cardoso, William S.; Marques, Edmar P.; Bezerra, Cicero W.B. [Universidade Federal do Maranhao (UFMA), Sao Luis, MA (Brazil). Departamento de Qumica; Ferreira, Antonio Ap. P. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Araraquara, SP (Brazil). Instituto de Quimica; Song, Chaojie; Zhang, Jiujun [Energy, Mining and Environment Portfolio, National Research Council of Canada, Vancouver, BC (Canada)

    2013-04-15

    Ruthenium-based hexacyanoferrate (RuHCF) thin film modified glassy carbon electrode was prepared by drop evaporation method. The RuHCF modified electrode exhibited four redox couples in strong acidic solution (pH 1.5) attributed to Fe(CN){sub 6}{sup 3-} ion and three ruthenium forms (Ru(II), Ru(III) and Ru(IV)), characteristic of ruthenium oxide compounds. The modified electrode displayed excellent electrocatalytic activity towards ethanol oxidation in the potential region where electrochemical processes Ru(III)-O-Ru(IV) and Ru(IV)-O-Ru(VI) occur. Impedance spectroscopy data indicated that the charge transfer resistance decreased with the increase of the applied potential and ethanol concentration, indicating the use of the RuHCF modified electrode as an ethanol sensor. Under optimized conditions, the sensor responded linearly and rapidly to ethanol concentration between 0.03 and 0.4 mol L{sup -1} with a limit of detection of 0.76 mmol L{sup -1}, suggesting an adequate sensitivity in ethanol analyses. (author)

  1. Comparative electrochemical sodium insertion/extraction behavior in layered NaxVS2 and NaxTiS2

    International Nuclear Information System (INIS)

    Lee, Eungje; Sahgong, SunHye; Johnson, Christopher S.; Kim, Youngsik

    2014-01-01

    This study investigates the electrochemical sodium insertion/extraction of Na x VS 2 , and Na x TiS 2 in the voltage range where either intercalation (0.2 ≤ x ≤ 1) or displacement-conversion reaction (x > 1) occurs. Both Na x VS 2 and Na x TiS 2 showed good reversible capacities, as high as ∼160 mAh/g at an average voltage of ∼1.9 V vs. Na in the region for the intercalation reaction (0.2 ≤ x ≤ 1). When sodium (Na) insertion was forced further to the x > 1 composition, Na x VS 2 exhibited the direct displacement-conversion reaction at 0.3 V vs. Na without further Na intercalation, which contrasted with the wider lithium intercalation range of 0 < x ≤ 2 for Li x VS 2 . The displacement-conversion reaction for Na x VS 2 (x > 1) was reversible with a specific capacity of above 200 mAh/g up to 15 cycles, but the displacement reaction for Na x TiS 2 (x > 1) was not observed

  2. Improvement of the electrochemical and electrocatalytic behavior of Prussian blue/carbon nanotubes composite via ionic liquid treatment

    International Nuclear Information System (INIS)

    Keihan, A.H.; Sajjadi, S.

    2013-01-01

    This paper reports the greatly improved electrochemical properties of Prussian blue/carbon nanotubes (PB/CNTs) modified glassy carbon electrode via a room temperature ionic liquid (RTIL) treatment. Firstly, the GC electrodes were modified with nanocomposites of RTIL/CNTs. Then, the PB nanoparticles were electrodeposited onto the modified electrode surface. Compared with the PB/CNTs/GC, the PB/RTIL/CNTs/GC electrodes showed higher PB surface concentration value of 2.42 × 10 −9 mol cm −2 , indicating that PB deposition efficiency was improved by 1.8 fold. The apparent diffusion coefficient for K + displayed value of 5.77 × 10 −11 cm 2 s −1 , which was one order of magnitude higher than that in the absence of RTIL. PB/RTIL/CNTs/GC modified electrodes showed higher electron transfer rate of 2.44 s −1 (2.35 times as much as that of PB/CNTs/GC electrodes). RTIL modified electrodes also displayed high sensitivity toward H 2 O 2 reduction (185.90 μA mM −1 cm −2 ) with low detection limit of 0.49 μM. The RTIL modified electrodes stored dry at room temperature preserved almost 100% of their initial currents over a period of 1 month, a useful property for commercial applications

  3. Electrochemical and anticorrosion behaviors of hybrid functionalized graphite nano-platelets/tripolyphosphate in epoxy-coated carbon steel

    Energy Technology Data Exchange (ETDEWEB)

    Mohammadi, Somayeh, E-mail: somaye.mohammadi32@aut.ac.ir [Department of Chemistry, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Shariatpanahi, Homeira [Corrosion Department, Research Institute of Petroleum Industry (RIPI), P.O. Box 18745-4163, Tehran (Iran, Islamic Republic of); Taromi, Faramarz Afshar [Department of Polymer Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Neshati, Jaber [Corrosion Department, Research Institute of Petroleum Industry (RIPI), P.O. Box 18745-4163, Tehran (Iran, Islamic Republic of)

    2016-08-15

    Highlights: • FGNP was combined with TPP to obtain a hybrid nano-particle. • TEM image showed uniform distribution of the hybrid nanoparticles in epoxy coating. • FGNP is a substrate for linking of TPP anions by hydrogen bonding. • FGNP as an accelerator, provides rapid iron phosphate passive film formation. • The hybrid nano-particle can provide long-term corrosion protection. - Abstract: Functionalized graphite nano-platelets (FGNP) were combined with tripolyphosphate (TPP) to gain a hybrid nano-particle (FGNP-TPP) with homogenous dispersion in epoxy, resulting in an excellent anti-corrosion coating for carbon steel substrate. Characterization analyses of the hybrid nano-particle were performed by FT-IR, SEM, XRD and TEM. TPP was linked to FGNP nano-particles by hydrogen bondings. Different epoxy coatings formulated with 1 wt.% of FGNP, FGNP-TPP and TPP were evaluated. Electrochemical investigations, salt spray and pull-off tests showed that the hybrid nano-particle can provide long-term corrosion protection compared to FGNP and TPP due to synergistic effect between FGNP as an accelerator and TPP as a corrosion inhibitor to produce a uniform and stable iron-phosphate passive film with high surface coverage.

  4. An electrochemical investigation of the corrosion behavior of Al-Si-Cu hypereutectic alloys in alcoholic environments

    International Nuclear Information System (INIS)

    Traldi, S. M.; Rossi, J. L.; Costa, I.

    2003-01-01

    Al-Si-Cu hypereutectic alloys produced by spray forming are mostly used in the automotive industry, especially for cylinder liners. they the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties- mainly wear resistance at high temperatures. The corrosion s resistance of these alloys in fuels, particularly alcoholic media, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarisation hove been used to evaluate the corrosion resistance of a hyper eutectic Al-Si-Cu alloy in alcoholic environments. the EIS tests carried out in pure ethanol, and ethanol with small additions (1 mM) of acid an chloride to investigate the effect of these contaminants on corrosion resistance. The corrosion resistance of a grey cast iron has also been evaluated in pure ethanol for comparison. The Al-Si-Cu alloy showed high corrosion resistance in pure ethanol, far superior to that of grey cast iron in the same medium. (Author) 13 refs

  5. Electrochemical Corrosion Behavior of Carbon Steel and Hot Dip Galvanized Steel in Simulated Concrete Solution with Different pH Values

    Directory of Open Access Journals (Sweden)

    Wanchen XIE

    2017-08-01

    Full Text Available Hot dip galvanizing technology is now widely used as a method of protection for steel rebars. The corrosion behaviors of Q235 carbon steel and hot galvanized steel in a Ca(OH2 solution with a pH from 10 to 13 was investigated by electrode potential and polarization curves testing. The results indicated that carbon steel and hot galvanized steel were all passivated in a strong alkaline solution. The electrode potential of hot dip galvanized steel was lower than that of carbon steel; thus, hot dip galvanized steel can provide very good anodic protection for carbon steel. However, when the pH value reached 12.5, a polarity reversal occurred under the condition of a certain potential. Hot dip galvanized coating became a cathode, and the corrosion of carbon steel accelerated. The electrochemical behaviors and passivation abilities of hot dip galvanized steel and carbon steel were affected by pH. The higher the pH value was, the more easily they were passivated.DOI: http://dx.doi.org/10.5755/j01.ms.23.3.16675

  6. Weight discrimination and unhealthy eating-related behaviors.

    Science.gov (United States)

    Sutin, Angelina; Robinson, Eric; Daly, Michael; Terracciano, Antonio

    2016-07-01

    Individuals with obesity often experience unfair treatment because of their body weight. Such experiences are associated with binge eating, but less is known about its association with other eating-related behaviors and whether these relations are specific to discrimination based on weight or extend to other attributions for discrimination. The present research uses a large national sample (N = 5129) to examine whether weight discrimination is associated with diet and meal rhythmicity, in addition to overeating, and whether these associations generalize to nine other attributions for discrimination. We found that in addition to overeating, weight discrimination was associated with more frequent consumption of convenience foods and less regular meal timing. These associations were generally similar across sex, age, and race. Discrimination based on ancestry, gender, age, religion, and physical disability were also associated with overeating, which suggests that overeating may be a general coping response to discrimination. Unfair treatment because of body weight is associated with unhealthy eating-related behaviors, which may be one pathway through which weight discrimination increases risk for weight gain and obesity. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Weight Discrimination and Unhealthy Eating-related Behaviors

    Science.gov (United States)

    Sutin, Angelina; Robinson, Eric; Daly, Michael; Terracciano, Antonio

    2016-01-01

    Individuals with obesity often experience unfair treatment because of their body weight. Such experiences are associated with binge eating, but less is known about its association with other eating-related behaviors and whether these relations are specific to discrimination based on weight or extend to other attributions for discrimination. The present research uses a large national sample (N=5,129) to examine whether weight discrimination is associated with diet and meal rhythmicity, in addition to overeating, and whether these associations generalize to nine other attributions for discrimination. We found that in addition to overeating, weight discrimination was associated with more frequent consumption of convenience foods and less regular meal timing. These associations were generally similar across sex, age, and race. Discrimination based on ancestry, gender, age, religion, and physical disability were also associated with overeating, which suggests that overeating may be a general coping response to discrimination. Unfair treatment because of body weight is associated with unhealthy eating-related behaviors, which may be one pathway through which weight discrimination increases risk for weight gain and obesity. PMID:26877216

  8. Treatment of addiction and addiction-related behavior

    Energy Technology Data Exchange (ETDEWEB)

    Dewey, Stephen L.; Brodie, Jonathan D.; Ashby, Jr., Charles R.

    2004-12-07

    The present invention provides a highly efficient method for treating substance addiction and for changing addiction-related behavior of a mammal suffering from substance addiction. The method includes administering to a mammal an effective amount of gamma vinylGABA or a pharmaceutically acceptable salt thereof. The present invention also provides a method of treatment of cocaine, morphine, heroin, nicotine, amphetamine, methamphetamine, or ethanol addiction by treating a mammal with an effective amount of gamma vinylGABA or a pharmaceutically acceptable salt thereof.

  9. Synapse-specific astrocyte gating of amygdala-related behavior.

    Science.gov (United States)

    Martin-Fernandez, Mario; Jamison, Stephanie; Robin, Laurie M; Zhao, Zhe; Martin, Eduardo D; Aguilar, Juan; Benneyworth, Michael A; Marsicano, Giovanni; Araque, Alfonso

    2017-11-01

    The amygdala plays key roles in fear and anxiety. Studies of the amygdala have largely focused on neuronal function and connectivity. Astrocytes functionally interact with neurons, but their role in the amygdala remains largely unknown. We show that astrocytes in the medial subdivision of the central amygdala (CeM) determine the synaptic and behavioral outputs of amygdala circuits. To investigate the role of astrocytes in amygdala-related behavior and identify the underlying synaptic mechanisms, we used exogenous or endogenous signaling to selectively activate CeM astrocytes. Astrocytes depressed excitatory synapses from basolateral amygdala via A 1 adenosine receptor activation and enhanced inhibitory synapses from the lateral subdivision of the central amygdala via A 2A receptor activation. Furthermore, astrocytic activation decreased the firing rate of CeM neurons and reduced fear expression in a fear-conditioning paradigm. Therefore, we conclude that astrocyte activity determines fear responses by selectively regulating specific synapses, which indicates that animal behavior results from the coordinated activity of neurons and astrocytes.

  10. Maternal depressive symptoms and weight-related parenting behaviors.

    Science.gov (United States)

    Morrissey, Taryn W

    2014-08-01

    This study examined associations between mothers' depressive symptoms and parenting behaviors related to children's nutrition and physical activity. Data from the Early Childhood Longitudinal Study-Birth Cohort, a nationally representative study of children from infancy through kindergarten entry. Contemporaneous and lagged associations between maternal depressive symptoms and mothers' parenting behaviors were tested, controlling for background characteristics. The mediating effect of use of a physician's office or clinic as a source for routine care was tested. At each wave, between 18 and 20 % of mothers were considered as having moderate or severe depressive symptoms. These mothers were 1.3 percentage points more likely to put their infants to bed with a bottle, 2.6 percentage points less likely to have rules about the foods their children eat, and their children were 3.0 percentage points less likely to be in bed by 9:00 p.m. than mothers lacking depressive symptoms. These mothers also reported that their families ate dinner together fewer nights per week, and their children watched more television per day, than non-depressed mothers. The use of a physician's office or clinic partially mediated associations between maternal depressive symptoms and whether infants went to bed with a bottle. Interventions that identify maternal depression early may be useful in promoting healthy parenting behaviors and weight outcomes among young children.

  11. Electrochemical Behavior of LiBr, LiI, and Li2Se in LiCl Molten Salt

    International Nuclear Information System (INIS)

    Choi, In Kyu; Do, Jae Bum; Hong, Sun Seok; Seo, Chung Seok

    2006-03-01

    The effect of fission products on the electrolytic reduction of uranium oxide has been studied. It has been reported that volatile fission products, such as Br, I, and Se, react with Li metal which is a reductant in the process to give LiBr, LiI, and Li 2 Se. These compounds are dissociated as corresponding anions and cations in the LiCl molten salt at 650 .deg. C. In this experiment, oxidation and reduction reaction of 3wt% of each compound in LiCl molten salt were investigated by cyclic voltammetry. For LiBr, redox reactions of cation and anion were reversible, while redox reactions of Li + and I - were irreversible. For Li 2 Se, about half of the produced Li metal was disappeared at the cathode and two anodic current curves were appeared. After the cyclic voltammetric measurements for each compound, chronopotentiometric experiment was carried out for one hour with 100 - 400 mA. After the electrolysis, no compounds gave Li metal in the porous MgO filter in which Li metal was produced at the cathode. However, LiCl salt was covered with Br 2 for LiBr electrolysis. Dark red color of Br 2 was easily removed by water. For LiI electrolysis, salt gave black color and I 2 was deposited on the Pt anode. For Li 2 Se electrolysis, black fine powders were precipitated in the salt. After the separation and dryness of the precipitates, it was analyzed with XRD and it turned out PtSe 2 . From the electrochemical experimental results, it was concluded that these compounds may affect the electrolytic reduction process of uranium oxide in the spent fuel

  12. Analysis of etchants behavior on the electrochemical etching amplification of fast-neutron-induced recoil particle tracks in polycarbonate

    International Nuclear Information System (INIS)

    Masnadi Shirazi Nezhad, K.

    1979-08-01

    The composition, concentration, and temperature of etchant are important parameters controlling electrochemical etching (ECE) amplification of charged particle tracks in polymers. These parameters were further studied for sohralir polycarbonate neutron dosimeter (Sohrabi 1974), using potassium hydroxide (KOH) and sodium hydroxide (NaOH) solutions, and a mixture of potassium hydroxide, ethanol, and water (PEW solution), at different concentrations applying a field strength of 32KV/cm at 2KHz frequency using 250 μ thick polycarbonate exposed to fast neutrons. The recoal track density per rad of neutrons, in general, was found to increase by increasing the etchant concentration reaching a semi-platean after which it increases again. This increase is up to a concentration at which a track removing process occurs and no tracks have been amplified anymore. This track removing process occurred at about 11 normality in both KOH (50% by weight) and NaOH (30% by weight) solution at 25degC. The mean track diameter, in general, passed through a cyclic variation having a maximun and a minimum. For NaOH solution, the track removing process occurred at the minimum point. In the three regions of the track diameter curve the tracks appear in different shapes especially in KOH solution. The PEW solution at its optimum conditions was more effective in terms of both sensitivity, track diameter and a shorter period of etching. The chemical mechanism of etching process may be explained to be a ''saponification'' process. These studies further support the adequacy of Sohrabi dosimeter for routing health physics and radiation research applications. The above parameters are further discussed and the results as well as the advantages and disadvantages of the above etchants are given. (author)

  13. Antibacterial effects, biocompatibility and electrochemical behavior of zinc incorporated niobium oxide coating on 316L SS for biomedical applications

    Science.gov (United States)

    Pradeep PremKumar, K.; Duraipandy, N.; Manikantan Syamala, Kiran; Rajendran, N.

    2018-01-01

    In the present study, Nb2O5 (NZ0) composite coatings with various concentrations of zinc (NZ2, NZ4 & NZ6) are produced on 316L SS by sol-gel method with the aim of improving its antibacterial activity, bone formability and corrosion resistance properties. This work studied the surface characterization of NZ0, NZ2, NZ4 & NZ6 coated 316L SS by ATR-FTIR, XRD, HR-SEM with EDAX. The synthesized coatings were different in the morphological aspects, NZ0 shows mesoporous morphology whereas irregular cluster like morphology was observed for the zinc incorporated coatings. The chemical composition of the NZ0 and NZ4 composite coatings were studied by XPS and the results revealed that the zinc exist as ZnO and Nb as Nb2O5 in the coatings. The increase in the concentration of zinc in Nb2O5 increases the hydrophilic nature identified by water contact angle studies. The potentiodynamic polarization studies in simulated body fluid reveals the increase in polarization resistance with decrease in current density (icorr) and electrochemical impedance spectroscopic studies with increase in charge transfer resistance (Rct) and double layer capacitance (Qdl) were observed for NZ4 coated 316L SS. The inhibition of Staphylococcus aureus and Escherichia coli bacteria were identified for NZ4 coated 316L SS by bacterial viability studies. The NZ4 coated 316L SS showed better Osseo-integration by spreading the MG 63 osteoblast cells. The study results imply that zinc incorporated Nb2O5 (NZ4) composite coating exhibits antibacterial activity and also enhance the corrosion resistance and biocompatibility of the 316L SS.

  14. Friction behavior and other material properties of nickel-titanium and titanium-molybdenum archwires following electrochemical surface refinement.

    Science.gov (United States)

    Meier, Miriam Julia; Bourauel, Christoph; Roehlike, Jan; Reimann, Susanne; Keilig, Ludger; Braumann, Bert

    2014-07-01

    The aim of this work was to investigate whether electrochemical surface treatment of nickel-titanium (NiTi) and titanium-molybdenum (TiMo) archwires (OptoTherm and BetaTitan; Ortho-Dent Specials, Kisdorf, Germany) reduces friction inside the bracket-archwire complex. We also evaluated further material properties and compared these to untreated wires. The material properties of the surface-treated wires (Optotherm/LoFrix and BetaTitan/LoFrix) were compared to untreated wires made by the same manufacturer (see above) and by another manufacturer (Neo Sentalloy; GAC, Bohemia, NY, USA). We carried out a three-point bending test, leveling test, and friction test using an orthodontic measurement and simulation system (OMSS). In addition, a pure bending test was conducted at a special test station, and scanning electron micrographs were obtained to analyze the various wire types for surface characteristics. Finally, edge beveling and cross-sectional dimensions were assessed. Force losses due to friction were reduced by 10 percentage points (from 36 to 26%) in the NiTi and by 12 percentage points (from 59 to 47%) in the TiMo wire specimens. Most of the other material properties exhibited no significant changes after surface treatment. While the three-point bending tests revealed mildly reduced force levels in the TiMo specimens due to diameter losses of roughly 2%, these force levels remained almost unchanged in the NiTi specimens. Compared to untreated NiTi and TiMo archwire specimens, the surface-treated specimens demonstrated reductions in friction loss by 10 and 12 percentage points, respectively.

  15. Electrochemical capacitor

    Science.gov (United States)

    Anderson, Marc A.; Liu, Kuo -Chuan; Mohr, Charles M.

    1999-10-05

    An inexpensive porous metal oxide material having high surface area, good conductivity and high specific capacitance is advantageously used in an electrochemical capacitor. The materials are formed in a sol-gel process which affords control over the properties of the resultant metal oxide materials.

  16. Electrochemical construction

    Science.gov (United States)

    Einstein, Harry; Grimes, Patrick G.

    1983-08-23

    An electrochemical cell construction features a novel co-extruded plastic electrode in an interleaved construction with a novel integral separator-spacer. Also featured is a leak and impact resistant construction for preventing the spill of corrosive materials in the event of rupture.

  17. Electrochemical device

    Science.gov (United States)

    Grimes, Patrick G.; Einstein, Harry; Bellows, Richard J.

    1988-01-12

    A tunnel protected electrochemical device features channels fluidically communicating between manifold, tunnels and cells. The channels are designed to provide the most efficient use of auxiliary power. The channels have a greater hydraulic pressure drop and electrical resistance than the manifold. This will provide a design with the optimum auxiliary energy requirements.

  18. Study of the electrochemical behavior at low temperatures of green anodes for Lithium ion batteries prepared with anatase TiO2 and water soluble sodium carboxymethyl cellulose binder

    International Nuclear Information System (INIS)

    Mancini, M.; Nobili, F.; Tossici, R.; Marassi, R.

    2012-01-01

    Highlights: ► Water soluble CMC and PVDF binders are used to prepare anatase TiO 2 electrodes. ► The electrochemical behavior of the different electrodes is studied between 20 and −30 °C. ► CMC/TiO 2 anodes show lower ICL, lower polarization and higher low-temperature capacity at high rates than PVDF/TiO 2 anodes. ► Electrochemical Impedance Spectroscopy results show better kinetics for CMC/TiO 2 electrodes. - Abstract: The electrochemical behavior at low temperatures of anatase TiO 2 electrodes for Lithium ion batteries have been evaluated by galvanostatic cycles in the temperature range 20 to −30 °C. Two different manufacturing processes have been used to prepare anatase anodes containing water soluble sodium carboxymethyl cellulose (CMC) or poly(vinilydene fluoride) (PVDF) as binder. The low temperature performances at different charge/discharge rates of TiO 2 /CMC and TiO 2 /PVDF electrodes are compared and discussed in terms of irreversible capacity loss (ICL) at the first cycle, capacity retention and reversible capacity. The kinetics of the electrodes containing CMC or PVDF is evaluated by Electrochemical Impedance Spectroscopy.

  19. An electrochemical investigation of the corrosion behavior of Al-Si-Cu hypereutectic alloys in alcoholic environments

    Directory of Open Access Journals (Sweden)

    Traldi, S. M.

    2003-12-01

    Full Text Available Al-Si-Cu hypereutetic alloys produced by spray forming are mostly used in the automotive industry, especially for cylinder liners. They have the advantage of low weight associated with low coefficient of thermal expansion and excellent mechanical properties - mainly wear resistance at high temperatures. The corrosion resistance of these alloys in fuels, particularly alcoholic media, however is not yet known. In this investigation, electrochemical impedance spectroscopy (EIS and potentiodynamic polarisation have been used to evaluate the corrosion resistance of a hypereutectic Al-Si-Cu alloy in alcoholic environments. The EIS tests were carried out in pure ethanol, and ethanol with small additions (1 mM of acid and chloride, to investigate the effect of these contaminants on corrosion resistance. The corrosion resistance of a grey cast iron has also been evaluated in pure ethanol for comparison. The Al-Si-Cu alloy showed high corrosion resistance in pure ethanol, far superior to that of grey cast iron in the same medium.

    Aleaciones hipereutécticas producidas por conformación por spray son muy empleadas en la industria automovilística, especialmente en los revestimientos de los cilindros. Tienen la ventaja de añadir menos peso con bajo coeficiente de expansión térmica y excelentes propiedades mecánicas, sobre todo resistencia al desgaste en altas temperaturas. Todavía, la resistencia a la corrosión de estas aleaciones en combustibles no es conocida. En este estudio fueron utilizadas las técnicas de espectroscopia de impedancia electroquímica y polarización potenciodinámica, para evaluar la resistencia a la corrosión de una aleación hipereutéctica Al-Si-Cu en medio alcohólico. Las pruebas fueron conducidas en etanol puro y etanol con pequeñas adiciones (1 mM de ácido y cloruro, con la finalidad de investigar el efecto de estos contaminantes en la resistencia a la corrosión. Hierro fundido gris, también fue

  20. The Influence of Charged Species on the Phase Behavior, Self-Assembly, and Electrochemical Performance of Block Copolymer Electrolytes

    Science.gov (United States)

    Thelen, Jacob Lloyd

    One of the major barriers to expanding the capacity of large-scale electrochemical energy storage within batteries is the threat of a catastrophic failure. Catastrophic battery pack failure can be initiated by a defect within a single battery cell. If the failure of a defective battery cell is not contained, the damage can spread and subsequently compromise the integrity of the entire battery back, as well as the safety of those in its surroundings. Replacing the volatile, flammable liquid electrolyte components found in most current lithium ion batteries with a solid polymer electrolyte (SPE) would significantly improve the cell-level safety of batteries; however, poor ionic conductivity and restricted operating temperatures compared to liquid electrolytes have plagued the practical application of SPEs. Rather than competing with the performance of liquid electrolytes directly, our approach to developing SPEs relies on increasing electrolyte functionality through the use of block copolymer architectures. Block copolymers, wherein two or more chemically dissimilar polymer chains are covalently bound, have a propensity to microphase separate into nanoscale domains that have physical properties similar to those of each of the different polymer chains. For instance, the block copolymer, polystyrene-b-poly(ethylene oxide) (SEO), has often been employed as a solid polymer electrolyte because the nanoscale domains of polystyrene (PS) can provide mechanical reinforcement, while the poly(ethylene oxide) microphases can solvate and conduct lithium ions. Block copolymer electrolytes (BCEs) formed from SEO/salt mixtures result in a material with the bulk mechanical properties of a solid, but with the ion conducting properties of a viscoelastic fluid. The efficacy SEO-based BCEs has been demonstrated; the enhanced mechanical functionality provided by the PS domains resist the propagation of dendritic lithium structures during battery operation, thus enabling the use of a

  1. Food-related parenting practices and child and adolescent weight and weight-related behaviors.

    Science.gov (United States)

    Loth, K; Fulkerson, J A; Neumark-Sztainer, D

    2014-03-01

    The prevalence of overweight and obesity in children has reached a concerning plateau in the past three decades, with overweight or obesity impacting approximately one-third of youth. Unhealthy weight-related behaviors, including dieting, unhealthy weight control practices and binge eating, are also a great public health concern for young people given both their high prevalence and harmful consequences. Food-related parenting practices, including food restriction and pressure-to-eat, have been associated with higher weight status, as well as the use of unhealthy weight-related behaviors, in children and adolescents. Physicians and other health care providers who work with families should discourage parents from using food restriction and pressure-to-eat parenting practices with their child or adolescent. Alternatively, parents should be empowered to promote healthy eating by focusing on making nutritious food items readily available within their home and modeling healthy food choices for their child or adolescent.

  2. Investigation of the electrochemical and electrocatalytic behavior of positively charged gold nanoparticle and L-cysteine film on an Au electrode

    International Nuclear Information System (INIS)

    Zhang Lingyan; Yuan Ruo; Chai Yaqing; Li Xuelian

    2007-01-01

    Positively charged gold nanoparticle (positively charged nano-Au), which was prepared, characterized by ξ-potential and transmission electron microscopy (TEM) was used in combination with L-cysteine to fabricate a modified electrode for electrocatalytic reaction of biomolecules. Compared with electrodes modified by negatively charged gold nanoparticle/L-cysteine, or L-cysteine alone, the electrode modified by the positively charged gold nanoparticle/L-cysteine exhibited excellent electrochemical behavior toward the oxidation of biomolecules such as ascorbic acid, dopamine and hydrogen peroxide. Moreover, the proposed mechanism for electrocatalytic response of positively charged gold nanoparticle was discussed. The immunosensor showed a specific to ascorbic acid in the range 5.1 x 10 -7 -6.7 x 10 -4 M and a low detection limit of 1.5 x 10 -7 M. The experimental results demonstrate that positively charged gold nanoparticle have more efficient electrocatalytic reaction than negatively charged gold nanoparticle, which opens up new approach for fabricating sensor

  3. Electrochemical corrosion behavior of acid treated strip cast AM50 and AZX310 magnesium alloys in 3.5 wt.% NaCl solution

    Directory of Open Access Journals (Sweden)

    Srinivasan Arthanari

    2017-09-01

    Full Text Available The influence of acid treatments on the surface morphology and electrochemical corrosion behavior of strip-cast AM50 and AZX310 alloys have been studied in the present investigation. The alloys were acid treated using H3PO4 (AT-1, HF (AT-2 and HNO3 (AT-3 for different treatment durations viz., 60, 300 and 600 s. The acid treatments produced a surface layer consisting of corresponding magnesium salts of the acids and were confirmed from the X-ray diffraction (XRD, scanning electron microscopy (SEM and energy dispersive X-ray analysis (EDAX. AT-1 treatment produced cracked and network porous morphology for AM50 and AZX310 alloys respectively and AT-3 treatment exhibited dense creaked surface layer formation while AT-2 does not produce any significant change in the morphology. Polarization studies revealed that, the acid treatment significantly altered the corrosion process by altering anodic and cathodic reaction rates of AM50 and AZX310 alloys. The HNO3 (AT-3 treatment was effective compared to other treatments to control the corrosion rate in the studied treatment conditions. The surface morphology and chemical composition of surface layer produced during the treatment was correlated to explain the corrosion results.

  4. Electrochemical behavior of current collectors for lithium batteries in non-aqueous alkyl carbonate solution and surface analysis by ToF-SIMS

    International Nuclear Information System (INIS)

    Myung, Seung-Taek; Sasaki, Yusuke; Sakurada, Shuhei; Sun, Yang-Kook; Yashiro, Hitoshi

    2009-01-01

    Several metals (Cu, Fe, Al, Ti, and Cr) as current collector for lithium-ion battery were investigated to understand their electrochemical behavior and passivation process in a non-aqueous alkyl carbonate solution containing LiPF 6 salt. From cyclic voltammetric study, it was found that Cu and Fe metals were dissolved into the electrolyte below 4 V vs. Li/Li + . Alternatively, Al and Ti were stable up to 5 V vs. Li/Li + . Their scratched surfaces at 5 V vs. Li/Li + were polarized in a transient mode and it was found that the surfaces were passivated during the polarization test. Formed passive film was composed of two hybrid layers: outer layer by metal (Al and Ti) fluoride and inner by metal oxide, as confirmed by time-of-flight secondary ion mass spectroscopy. Presence of HF in the electrolyte was indispensible to form the metal fluoride layer on the oxide layer. The outer fluoride layer would protect the inner oxide layer and metal substrate from HF attack, bringing about satisfactory corrosion resistance under lithium-ion battery environment.

  5. Comparative investigation on electrochemical behavior of hydroquinone at carbon ionic liquid electrode, ionic liquid modified carbon paste electrode and carbon paste electrode

    International Nuclear Information System (INIS)

    Zhang, Ya; Zheng, Jian Bin

    2007-01-01

    Ionic liquid, 1-heptyl-3-methylimidazolium hexafluorophosphate (HMIMPF 6 ), has been used to fabricate two new electrodes, carbon ionic liquid electrode (CILE) and ionic liquid modified carbon paste electrode (IL/CPE), using graphite powder mixed with HMIMPF 6 or the mixture of HMIMPF 6 /paraffin liquid as the binder, respectively. The electrochemical behaviors of hydroquinone at the CILE, the IL/CPE and the CPE were investigated in phosphate buffer solution. At all these electrodes, hydroquinone showed a pair of redox peaks. The order of the current response and the standard rate constant of hydroquinone at these electrodes were as follows: CILE > IL/CPE > CPE, while the peak-to-peak potential separation was in an opposite sequence: CILE < IL/CPE < CPE. The results show the superiority of CILE to IL/CPE and CPE, and IL/CPE to CPE in terms of promoting electron transfer, improving reversibility and enhancing sensitivity. The CILE was chosen as working electrode to determine hydroquinone by differential pulse voltammetry, which can be used for sensitive, simple and rapid determination of hydroquinone in medicated skin cosmetic cream

  6. Interfacial stability and electrochemical behavior of Li/LiFePO4 batteries using novel soft and weakly adhesive photo-ionogel electrolytes

    Science.gov (United States)

    Aidoud, D.; Etiemble, A.; Guy-Bouyssou, D.; Maire, E.; Le Bideau, J.; Guyomard, D.; Lestriez, B.

    2016-10-01

    We have developed flexible polymer-gel electrolytes based on a polyacrylate cross-linked matrix that confines an ionic liquid doped with a lithium salt. Free-standing solid electrolyte membrane is obtained after UV photo-polymerization of acrylic monomers dissolved inside the ionic liquid/lithium salt mixture. The liquid precursor of the photo-ionogel may also be directly deposited onto porous composite electrode, which results in all-solid state electrode/electrolyte stacking after UV illumination. Minor variations in the polymer component of the electrolyte formulation significantly affect the electrochemical behavior in LiFePO4/lithium and lithium/lithium cells. The rate performance increases with an increase of the ionic conductivity, which decreases with the polymer content and decreases with increasing oxygen content in the polyacrylate matrix. Their fairly low modulus endow them weak and beneficial pressure-sensitive-adhesive character. X-Rays Tomography shows that the solid-state photo-ionogel electrolytes keep their integrity upon cycling and that their surface remains smooth. The coulombic efficiency of LiFePO4/lithium cells increases with an increase of the adhesive strength of the photo-ionogel, suggesting a relationship between the contact intimacy at the lithium/photo-ionogel interface and the efficiency of the lithium striping/plating. In lithium/lithium cells, only the photo-ionogels with the higher adhesion strength are able to allow the reversible striping/plating of lithium.

  7. Thermodynamic behavior of glassy state of structurally related compounds.

    Science.gov (United States)

    Kaushal, Aditya Mohan; Bansal, Arvind Kumar

    2008-08-01

    Thermodynamic properties of amorphous pharmaceutical forms are responsible for enhanced solubility as well as poor physical stability. The present study was designed to investigate the differences in thermodynamic parameters arising out of disparate molecular structures and associations for four structurally related pharmaceutical compounds--celecoxib, valdecoxib, rofecoxib, and etoricoxib. Conventional and modulated temperature differential scanning calorimetry were employed to study glass forming ability and thermodynamic behavior of the glassy state of model compounds. Glass transition temperature of four glassy compounds was in a close range of 327.6-331.8 K, however, other thermodynamic parameters varied considerably. Kauzmann temperature, strength parameter and fragility parameter showed rofecoxib glass to be most fragile of the four compounds. Glass forming ability of the compounds fared similar in the critical cooling rate experiments, suggesting that different factors were determining the glass forming ability and subsequent behavior of the compounds in glassy state. A comprehensive understanding of such thermodynamic facets of amorphous form would help in rationalizing the approaches towards development of stable glassy pharmaceuticals.

  8. Treatment of addiction and addiction-related behavior

    Energy Technology Data Exchange (ETDEWEB)

    Dewey, Stephen L. (Manorville, NY); Brodie, Jonathan D. (Cos Cob, CT); Ashby, Jr., Charles R. (Miller Place, NY)

    2003-01-01

    The present invention provides a highly efficient method for treating substance addiction and for changing addiction-related behavior of a mammal suffering from substance addiction. The method includes administering to a mammal an effective amount of gamma vinylGABA or a pharmaceutically acceptable salt thereof. The present invention also provides a method of treatment of cocaine, morphine, heroin, nicotine, amphetamine, methamphetamine, or ethanol addiction by treating a mammal with an effective amount of gamma vinylGABA or a pharmaceutically acceptable salt thereof. In one embodiment, the method of the present invention includes administering to the mammal an effective amount of a composition which increases central nervous system GABA levels wherein the effective amount is sufficient to diminish, inhibit or eliminate behavior associated with craving or use of drugs of abuse. The composition includes GVG, gabapentin, valproic acid, progabide, gamma-hydroxybutyric acid, fengabine, cetylGABA, topiramate or tiagabine or a pharmaceutically acceptable salt thereof, or an enantiomer or a racemic mixture thereof.

  9. Single-Molecule Electrochemical Gating in Ionic Liquids

    DEFF Research Database (Denmark)

    Kay, Nicola J.; Higgins, Simon J.; Jeppesen, Jan O.

    2012-01-01

    The single-molecular conductance of a redox active molecular bridge has been studied in an electrochemical single-molecule transistor configuration in a room-temperature ionic liquid (RTIL). The redox active pyrrolo-tetrathiafulvalene (pTTF) moiety was attached to gold contacts at both ends through...... −(CH2)6S– groups, and gating of the redox state was achieved with the electrochemical potential. The water-free, room-temperature, ionic liquid environment enabled both the monocationic and the previously inaccessible dicationic redox states of the pTTF moiety to be studied in the in situ scanning...... and decreases again as the second redox process is passed. This is described as an “off–on–off–on–off” conductance switching behavior. This molecular conductance vs electrochemical potential relation could be modeled well as a sequential two-step charge transfer process with full or partial vibrational...

  10. Parental educational practices in relation to children's anxiety disorder-related behavior.

    Science.gov (United States)

    Mellon, Robert C; Moutavelis, Adrianos G

    2011-08-01

    Schoolchildren reported their parents' use of aversive control and positive reinforcement contingencies in their educational interventions, as well as parental non-responsiveness to their requests for educational assistance. They also reported their own levels of six dimensions of anxiety disorder-related phenomena. Both parental use of aversive control and non-responsiveness were directly related to overall levels of child anxiety disorder-related behavior; these correlations were more robust than those observed in previous investigations of more diffuse dimensions of parenting style and trait anxiety. Panic disorder/agoraphobia and Generalized anxiety disorder were the dimensions most strongly correlated with both parental aversive control and non-responsiveness, while Compulsive behavior was uniquely uncorrelated with parental non-responsiveness and uniquely correlated with parental use of positive reinforcement contingencies. Differences in the magnitudes of correlations between anxiety disorder-related dimensions and parental educational practices are interpreted in terms of the probable differential effectiveness of their constituent behaviors in terminating parent-mediated negative reinforcers. Copyright © 2011 Elsevier Ltd. All rights reserved.

  11. Differences in the electrochemical behavior of ruthenium and iridium oxide in electrocatalytic coatings of activated titanium anodes prepared by the sol–gel procedure

    Directory of Open Access Journals (Sweden)

    VLADIMIR V. PANIĆ

    2010-10-01

    Full Text Available The electrochemical characteristics of Ti0.6Ir0.4O2/Ti and Ti0.6Ru0.4O2/Ti anodes prepared by the sol–gel procedure from the corresponding oxide sols, obtained by force hydrolysis of the corresponding metal chlorides, were compared. The voltammetric properties in H2SO4 solution indicate that Ti0.6Ir0.4O2/Ti has more pronounced pseudocapacitive characteristics, caused by proton-assisted, solid state surface redox transitions of the oxide. At potentials negative to 0.0 VSCE, this electrode is of poor conductivity and activity, while the voltammetric behavior of the Ti0.6Ru0.4O2/Ti electrode is governed by proton injection/ejection into the oxide structure. The Ti0.6Ir0.4O2/Ti electrode had a higher electrocatalytical activity for oxygen evolution, while the investigated anodes were of similar activity for chlorine evolution. The potential dependence of the impedance characteristics showed that the Ti0.6Ru0.4O2/Ti electrode behaved like a capacitor over a wider potential range than the Ti0.6Ir0.4O2/Ti electrode, with fully-developed pseudocapacitive properties at potentials positive to 0.60 VSCE. However, the impedance characteristics of the Ti0.6Ir0.4O2/Ti electrode changed with increasing potential from resistor-like to capacitor-like behavior.

  12. Relations of Behavioral Autonomy to Health Outcomes Among Emerging Adults With and Without Type 1 Diabetes

    Science.gov (United States)

    Reynolds, Kerry A.; Becker, Dorothy; Escobar, Oscar; Siminerio, Linda

    2014-01-01

    Objective To examine the relation of behavioral autonomy to psychological, behavioral, and physical health among emerging adults with and without type 1 diabetes. Methods High school seniors with (n = 118) and without type 1 diabetes (n = 122) completed online questionnaires for three consecutive years. Behavioral autonomy, psychological health, risk behaviors, and diabetes outcomes were assessed. Regression analyses were conducted to predict Time 2 and 3 outcomes, controlling for Time 1 outcomes. Results There were no group differences in behavioral autonomy. Behavioral autonomy predicted better psychological health but only for emerging adults without diabetes. Behavioral autonomy was related to increased risk behavior for both groups. Behavioral autonomy was unrelated to self-care but predicted better glycemic control for females. Conclusions Behavioral autonomy may be beneficial for psychological health, but is related to increased risk behavior. The implications of behavioral autonomy for emerging adults with type 1 diabetes require careful consideration. PMID:25157070

  13. Antioxidant activity and electrochemical elucidation of the enigmatic redox behavior of curcumin and its structurally modified analogues

    International Nuclear Information System (INIS)

    Jha, Niki S.; Mishra, Satyendra; Jha, Shailendra K.; Surolia, Avadhesha

    2015-01-01

    Highlights: • Structural analogues of curcumin have been synthesized. • Confirmation of redox behaviour emanates from H- shift from central methylene group in curcumin. • Mechanism of curcumin oxidation has been proposed. • Correlation between redox behavior and antioxidant activity has been established. - Abstract: Here, we report studies on the antioxidant activity and redox behavior of curcumin and its structurally modified synthetic analogues. We have synthesized a number of analogues of curcumin which abrogate its keto-enol tautomerism or substitute the methylene group at the centre of its heptadione moiety implicated in the hydride transfer and studied their redox property. From cyclic voltammetric studies, it is demonstrated that H- atom transfer from CH 2 group at the center of the heptadione link also plays an important role in the antioxidant properties of curcumin along with that of its phenolic –OH group. In addition, we also show that the conversion of 1, 3- dicarbonyl moiety of curcumin to an isosteric heterocycle as in pyrazole curcumin, which decreases its rotational freedom, leads to an improvement of its redox properties as well as its antioxidant activity

  14. CREB Overexpression Ameliorates Age-related Behavioral and Biophysical Deficits

    Science.gov (United States)

    Yu, Xiao-Wen

    Age-related cognitive deficits are observed in both humans and animals. Yet, the molecular mechanisms underlying these deficits are not yet fully elucidated. In aged animals, a decrease in intrinsic excitability of pyramidal neurons from the CA1 sub-region of hippocampus is believed to contribute to age-related cognitive impairments, but the molecular mechanism(s) that modulate both these factors has yet to be identified. Increasing activity of the transcription factor cAMP response element-binding protein (CREB) in young adult rodents has been shown to facilitate cognition, and increase intrinsic excitability of their neurons. However, how CREB changes with age, and how that impacts cognition in aged animals, is not clear. Therefore, we first systematically characterized age- and training-related changes in CREB levels in dorsal hippocampus. At a remote time point after undergoing behavioral training, levels of total CREB and activated CREB (phosphorylated at S133, pCREB) were measured in both young and aged rats. We found that pCREB, but not total CREB was significantly reduced in dorsal CA1 of aged rats. Importantly, levels of pCREB were found to be positively correlated with short-term spatial memory in both young and aged rats i.e. higher pCREB in dorsal CA1 was associated with better spatial memory. These findings indicate that an age-related deficit in CREB activity may contribute to the development of age-related cognitive deficits. However, it was still unclear if increasing CREB activity would be sufficient to ameliorate age-related cognitive, and biophysical deficits. To address this question, we virally overexpressed CREB in CA1, where we found the age-related deficit. Young and aged rats received control or CREB virus, and underwent water maze training. While control aged animals exhibited deficits in long-term spatial memory, aged animals with CREB overexpression performed at levels comparable to young animals. Concurrently, aged neurons

  15. Unique crystallization behavior of sodium manganese pyrophosphate Na2MnP2O7 glass and its electrochemical properties

    Directory of Open Access Journals (Sweden)

    Morito Tanabe

    2017-06-01

    Full Text Available Crystallization behavior of Na2MnP2O7 precursor glass was examined. Layered type Na2MnP2O7 was formed at 461 °C for 3 h in N2 filled electric furnace. Irreversible phase change was confirmed from layered Na2MnP2O7 to β-Na2MnP2O7 over 600 °C. At 650 °C crystallized phase was completely changed to β-phase. By means of charge and discharge testing it is found that layered Na2MnP2O7 is also active as cathode in sodium ion batteries. We found glass-ceramics technology is one of the suitable process for the synthesis of layered Na2MnP2O7 cathode without any complicate process.

  16. Behavior of Electrochemically Prepared CuInSe2 as Photovoltaic Absorber in thin Film Solar Cells

    International Nuclear Information System (INIS)

    Guillen, C; Martinez, M.A.; Dona, J. M.; Herrero, J; Gutierrez, M. T.

    2000-01-01

    Two different objectives have been pursued in the present investigation: 1) optimization of the CuInSe, preparation parameters from electrodeposited precursors, and 2) evaluation of their photovoltaic behavior by preparing and enhancing Mo/CuInSe,/CdS/TCO devices. When Cu-In-Se precursors are directly electrodeposited, the applied potential fit is essential to improve the photovoltaic performance. Suitable absorbers have been also obtained by evaporating an In layer onto electrodeposited Cu-Se precursors. In this case, the substrate temperature during evaporation determines the CuInSe, quality. Similar results have been reached by substituting typical Mo-coated glass substrates by flexible Mo foils. Different TCO tested (ZnO and ITO) have been found equivalent as front electrical contact in the devices. Solar cell performance can be improved by annealing in air at 200 degree centigree. (Author) 46 refs

  17. The influence of the pyrolysis temperature on the electrochemical behavior of carbon-rich SiCN polymer-derived ceramics as anode materials in lithium-ion batteries

    Science.gov (United States)

    Reinold, Lukas Mirko; Yamada, Yuto; Graczyk-Zajac, Magdalena; Munakata, Hirokazu; Kanamura, Kiyoshi; Riedel, Ralf

    2015-05-01

    Within this study we report on the impact of the pyrolysis temperature on the structural and electrochemical properties of the poly(phenylvinylsilylcarbodiimide) derived silicon carbonitride (SiCN) ceramic. Materials pyrolysed at 800 °C and 1300 °C, SiCN 800 and SiCN 1300, are found amorphous. Raman spectroscopy measurements indicate the increase in ordering of the free carbon phase with increasing pyrolysis temperature which leads to lower capacity recovered by SiCN 1300. Significant hysteresis is found for materials pyrolysed at 800 °C during electrochemical lithium insertion/extraction. This feature is attributed to much higher hydrogen content in SiCN 800 sample. An aging of SiCN 800 reflected by a change of elemental composition upon contact to air and a strong film formation are attenuated at a higher pyrolysis temperature. Single particle microelectrode investigation on SiCN 800 and SiCN 1300 clarify different electrochemical behavior of the materials. Much lower charge transfer resistance of SiCN 1300 in comparison to SiCN 800 explains better high currents electrochemical performance. Lithium ions diffusion coefficient Dmin ranges from 3.2 10-9 cm2s-1 to 6.4 10-11 cm2s-1 and is independent on the potential.

  18. Leadership Is Positively Related to Athletic Training Students' Clinical Behaviors

    Science.gov (United States)

    Kutz, Matthew R.

    2012-01-01

    Context: Leadership development by health professionals positively affects patient outcomes. Objective: To 1) determine if there is any relationship between demonstrated leadership behaviors and clinical behaviors among entry-level AT students (ATS); 2) to explore if the level of leadership behavior changes between ATS level; and 3) to determine…

  19. Socioeconomic differences in adolescent health-related behavior differ by gender

    NARCIS (Netherlands)

    Pitel, Lukas y; Geckova, Andrea Madarasova; Reijneveld, Sijmen A.; van Dijk, Jitse P.

    BACKGROUND: Many studies of adolescent health-related behaviors have assessed the effects of gender and parental socioeconomic position (SEP) but not their mutual modification. We investigated socioeconomic differences in health-related behaviors among Slovak adolescents and the potential

  20. Relations between Children's Levels of Responsiveness and Resistance, Maternal Interaction Behaviors, and Children's Social Behaviors with Peers in School

    Science.gov (United States)

    Salinas, Daniela; Neitzel, Carin

    2017-01-01

    Children's peer relationships have their origins in family relationships. The present study focuses on the relative importance of children's levels of responsiveness and/or resistance during mother-child interactions and tests a model of the direct and indirect relations between mother interaction behaviors and children's social behaviors with…

  1. Electrochemical behavior of folic acid at calixarene based chemically modified electrodes and its determination by adsorptive stripping voltammetry

    International Nuclear Information System (INIS)

    Vaze, Vishwanath D.; Srivastava, Ashwini K.

    2007-01-01

    Voltammetric behavior of folic acid at plain carbon paste electrode and electrode modified with calixarenes has been studied. Two peaks for irreversible oxidation were observed. Out of the three calixarenes chosen for modification of the electrodes, p-tert-butyl-calix[6]arene modified electrode (CME-6) was found to have better sensitivity for folic acid. Chronocoulometric and differential pulse voltammetric studies reveal that folic acid can assemble at CME-6 to form a monolayer whose electron transfer rate is 0.00273 s -1 with 2-electron/2-proton transfer for the peak at +0.71 V against SCE. An adsorption equilibrium constant of 5 x 10 3 l/mol for maximum surface coverage of 2.89 x 10 -10 mol/cm 2 was obtained. The current is found to be rectilinear with concentration by differential pulse voltammetry. However, linearity in the lower range of concentration 8.79 x 10 -12 M to 1.93 x 10 -9 M with correlation coefficient of 0.9920 was achieved by adsorptive stripping voltammetry. The limit of detection obtained was found to be 1.24 x 10 -12 M. This method was used for the determination of folic acid in a variety of samples, viz. serum, asparagus, spinach, oranges and multivitamin preparations

  2. The Influence of Post-Build Microstructure on the Electrochemical Behavior of Additively Manufactured 17-4 PH Stainless Steel.

    Science.gov (United States)

    Stoudt, M R; Ricker, R E; Lass, E A; Levine, L E

    2017-03-01

    The additive manufacturing (AM) build process produces a segregated microstructure with significant variations in composition and phases that are uncommon in traditional wrought materials. As such, the relationship between the post-build microstructure and the corrosion resistance is not well understood. Stainless steel alloy 17-4PH is an industrially-relevant alloy for applications requiring high-strength and good corrosion resistance. A series of potentiodynamic scans conducted in a deaerated 0.5 mol/L NaCl solution evaluated the influence of these microstructural differences on the pitting behavior of SS17-4. The pitting potentials were found to be higher in the samples of additively-processed material than in samples of the alloy in wrought form. This indicates that the additively-processed material is more resistant to localized corrosion and pitting in this environment than the wrought alloy. The results also suggest that after homogenization, the additively-produced SS17-4 could be more resistant to pitting than wrought SS17-4 in an actual service environment.

  3. Electrochemical behavior of folic acid at calixarene based chemically modified electrodes and its determination by adsorptive stripping voltammetry

    Energy Technology Data Exchange (ETDEWEB)

    Vaze, Vishwanath D. [Department of Chemistry, University of Mumbai, Vidyanagari, Santacruz (East), Mumbai 400098 (India); Srivastava, Ashwini K. [Department of Chemistry, University of Mumbai, Vidyanagari, Santacruz (East), Mumbai 400098 (India)], E-mail: aksrivastava@chem.mu.ac.in

    2007-12-31

    Voltammetric behavior of folic acid at plain carbon paste electrode and electrode modified with calixarenes has been studied. Two peaks for irreversible oxidation were observed. Out of the three calixarenes chosen for modification of the electrodes, p-tert-butyl-calix[6]arene modified electrode (CME-6) was found to have better sensitivity for folic acid. Chronocoulometric and differential pulse voltammetric studies reveal that folic acid can assemble at CME-6 to form a monolayer whose electron transfer rate is 0.00273 s{sup -1} with 2-electron/2-proton transfer for the peak at +0.71 V against SCE. An adsorption equilibrium constant of 5 x 10{sup 3} l/mol for maximum surface coverage of 2.89 x 10{sup -10} mol/cm{sup 2} was obtained. The current is found to be rectilinear with concentration by differential pulse voltammetry. However, linearity in the lower range of concentration 8.79 x 10{sup -12} M to 1.93 x 10{sup -9} M with correlation coefficient of 0.9920 was achieved by adsorptive stripping voltammetry. The limit of detection obtained was found to be 1.24 x 10{sup -12} M. This method was used for the determination of folic acid in a variety of samples, viz. serum, asparagus, spinach, oranges and multivitamin preparations.

  4. Electrochemical cell

    Science.gov (United States)

    Kaun, T.D.

    An improved secondary electrochemical cell is disclosed having a negative electrode of lithium aluminum, a positive electrode of iron sulfide, a molten electrolyte of lithium chloride and potassium chloride, and the combination that the fully charged theoretical capacity of the negative electrode is in the range of 0.5 to 1.0 that of the positive electrode. The cell thus is negative electrode limiting during discharge cycling. Preferably, the negative electrode contains therein, in the approximate range of 1 to 10 volume % of the electrode, an additive from the materials of graphitized carbon, aluminum-iron alloy, and/or magnesium oxide.

  5. Electrochemical behavior of 45S5 bioactive ceramic coating on Ti6Al4V alloy for dental applications

    Science.gov (United States)

    Machado López, M. M.; Espitia Cabrera, M. I.; Faure, J.; Contreras García, M. E.

    2016-04-01

    Titanium and its alloys are widely used as implant materials because of their mechanical properties and non-toxic behavior. Unfortunately, they are not bioinert, which means that they can release ions and can only fix the bone by mechanical anchorage, this can lead to the encapsulation of dense fibrous tissue in the body. The bone fixation is required in clinical conditions treated by orthopedic and dental medicine. The proposal is to coat metallic implants with bioactive materials to establish good interfacial bonds between the metal substrate and bone by increasing bioactivity. Bioactive glasses, ceramics specifically 45 S5 Bioglass, have drawn attention as a serious functional biomaterial because osseointegration capacity. The EPD method of bioglass gel precursor was proposed in the present work as a new method to obtain 45S5/Ti6A14V for dental applications. The coatings, were thermally treated at 700 and 800°C and presented the 45 S5 bioglass characteristic phases showing morphology and uniformity with no defects, quantification percentages by EDS of Si, Ca, Na, P and O elements in the coating scratched powders, showed a good proportional relationship demonstrating the obtention of the 45S5 bioglass. The corrosion tests were carried out in Hank's solution. By Tafel extrapolation, Ti6Al4V alloy showed good corrosion resistance in Hank's solution media, by the formation of a passivation layer on the metal surface, however, in the system 45S5/Ti6Al4V there was an increase in the corrosion resistance; icon-, Ecorr and corrosion rate decreased, the mass loss and the rate of release of ions, were lower in this system than in the titanium alloy without coating.

  6. Electrochemical Behavior of Catechol and Hydroquinone at Copper Doped Poly (Methyl Red Coated Hydroxyl Multiwalled Carbon Nanotube Film and Their Simultaneous Determination in Water Samples

    Directory of Open Access Journals (Sweden)

    Ying Zhang

    2014-09-01

    Full Text Available A glassy carbon electrode modified with copper doped poly (methyl red coated hydroxyl multiwalled carbon nanotube film (Cu-PMR/MWCNTs, was developed to serve as a sensor for simultaneous determination of Hydroquinone (HQ and catechol (CC in this paper. The fabricated electrode showed excellent electrocatalytic behaviors towards the oxidation of HQ and CC with the enhancement of the redox peak current and the decrease of the peak-to-peak separation. Under the optimized condition, the individual determination of HQ or CT in their mixtures was performed, the response peak currents of the modified electrodes were linear over ranges of 8.0´10-7~4.0´10-4 M (R2=0.999 for CT and 5.0´10-7~2.0´10-4 M (R2=0.993 for HQ. The sensor also exhibited good sensitivity with the detection limit of 1.0´10-8 mol/L and 5.0´10-8 mol/L for HQ and CT, respectively. The simultaneous determination of HQ and CC was demonstrated by simultaneously changing their concentrations. The reduction peak currents of HQ and CC increased linearly with the concentration of their own in the range of 8´10-7 and 2.0´10-4 M for HQ and CC, with correlation coefficients of 0.994 and 0.995 (S/N=3, respectively. This study provides a new kind of composite modified electrode for electrochemical sensors with good selectivity and strong anti-interference. It has been applied to simultaneous determination of HQ and CT in water sample with high selectivity.

  7. Electrochemical behaviors of Janus Green B in through-hole copper electroplating: An insight by experiment and density functional theory calculation using Safranine T as a comparison

    International Nuclear Information System (INIS)

    Wang, Chong; Zhang, Jinqiu; Yang, Peixia; An, Maozhong

    2013-01-01

    Highlights: ► Using Safranine T as a comparison to study the mechanism of JGB in the through-hole electroplating. ► Quantum chemical calculation is employed to analysis electronic properties and orbital information of levelers in the present paper. ► Finding out the probable reactive site for the adsorption of JGB on the copper surface. ► Offering some theoretical information to design and synthesize new additives for electroplating. -- Abstract: Janus Green B (JGB) and Safranine T (ST) were used as levelers in the through-hole (TH) copper electroplating experiments. Although JGB and ST have a similar part in the structure, the results indicate that JGB is an effective leveler used for TH electroplating whereas ST is not. A uniform plating is obtained using 1 ppm JGB as a leveler. In contrast, ST could not increase the value of uniformity power (UP). Electrochemical behaviors of JGB and ST were evaluated by potentiodynamic polarization and galvanostatic measurements using rotating disk electrode (RDE). JGB could effectively affect the cathodic polarization. However, the addition of ST changed the cathodic polarization weakly. Quantum chemical calculations based on density functional theory (DFT) were used to obtain some electronic properties and orbital information. The calculations on frontier molecular orbital suggested that the electron donating ability of JGB was higher than that of ST, which gave rise to stronger adsorption of JGB on the cathodic surface and stronger inhibition of copper electrodeposition on the cathode. Furthermore, the results of frontier molecular orbital and Fukui function distributions showed that the N=N region or aminoazobenzene region of JGB was the probable reactive site for the adsorption of JGB on the copper surface

  8. Electrochemical Properties of High Surface Area Vanadium Oxide Aerogels

    National Research Council Canada - National Science Library

    Dong, Winny

    2001-01-01

    .... Traditional composite electrode structures have prevented truly quantitative analysis of surface area effects in nanoscale battery materials, as well as a study of their innate electrochemical behavior...

  9. Attachment representations in adulthood: relations with parental behaviors.

    Science.gov (United States)

    Koren-Karie, N

    2000-01-01

    The paper presents two standardized measurements of attachment. The Strange Situation Procedure is an observational measure of the reaction of 12-18-month-old infants to their parent after being exposed to brief separations from him/her. Four main types of responses are noted, and have been noted in a range of cultures. The second measure is the Adult Attachment Interview which is a semi-structured interview of 18 questions that discusses childhood memories and assesses the current state of mind with regard to attachment issues. Four types of characteristic response styles have been noted in a range of cultures, and this measure seems to be related to certain types of parenting. Studies of the link between the two measures have been complicated, as the adult measure does not include the capacity to be available for the child. A further instrument, the Maternal Empathic Understanding Procedure, designed to assess parent's ability to see things from the child's point of view, is suggested as a possible mediator between parental attachment style and parenting behavior. These studies permit standardized evaluation of parenting skills, facilitate the study of intergenerational transmission of these skills, and suggest the possibility of psychotherapeutic interventions that focus on these areas.

  10. Carbon diffusion behavior in molybdenum at relatively low temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Hiraoka, Yutaka, E-mail: hiraoka@dap.ous.ac.j [Department of Applied Physics, Okayama University of Science, 1-1 Ridai-cho, Okayama 700-0005 (Japan); Imamura, Kyosuke [Graduate School of Science, Okayama University of Science, 1-1 Ridai-cho, Okayama 700-0005 (Japan); Kadokura, Takanori; Yamamoto, Yoshiharu [Materials Research Department, A.L.M.T. Corp., 2 Iwasekoshi-machi, Toyama 931-8543 (Japan)

    2010-01-07

    Purpose of this study is to investigate the carbon diffusion behavior in pure molybdenum at relatively low temperatures by means of fracture surface observation. Carbon addition was performed at a temperature of 1273-1373 K with the heating time being changed. Fracture surface of the specimen after carbon addition was examined using SEM and the carbon diffusion distance was estimated from the change of fracture mode as a function of the distance from the surface. Results are summarized as follows. First, the carbon diffusion distance increased approximately linearly with the increase of heating time from 1.2 to 10.8 ks. This relationship does not agree with that obtained at much higher temperatures. From Arrhenius plots of the slope of the straight line and the temperature, activation energy was calculated (155 kJ/mol). Secondly, the carbon diffusion distance estimated in this study was generally larger than that simulated using the data of Rudman, particularly at a longer heating time.

  11. Parents' obesity-related behavior and confidence to support behavioral change in their obese child: data from the STAR study.

    Science.gov (United States)

    Arsenault, Lisa N; Xu, Kathleen; Taveras, Elsie M; Hacker, Karen A

    2014-01-01

    Successful childhood obesity interventions frequently focus on behavioral modification and involve parents or family members. Parental confidence in supporting behavior change may be an element of successful family-based prevention efforts. We aimed to determine whether parents' own obesity-related behaviors were related to their confidence in supporting their child's achievement of obesity-related behavioral goals. Cross-sectional analyses of data collected at baseline of a randomized control trial testing a treatment intervention for obese children (n = 787) in primary care settings (n = 14). Five obesity-related behaviors (physical activity, screen time, sugar-sweetened beverage, sleep duration, fast food) were self-reported by parents for themselves and their child. Behaviors were dichotomized on the basis of achievement of behavioral goals. Five confidence questions asked how confident the parent was in helping their child achieve each goal. Logistic regression modeling high confidence was conducted with goal achievement and demographics as independent variables. Parents achieving physical activity or sleep duration goals were significantly more likely to be highly confident in supporting their child's achievement of those goals (physical activity, odds ratio 1.76; 95% confidence interval 1.19-2.60; sleep, odds ratio 1.74; 95% confidence interval 1.09-2.79) independent of sociodemographic variables and child's current behavior. Parental achievements of TV watching and fast food goals were also associated with confidence, but significance was attenuated after child's behavior was included in models. Parents' own obesity-related behaviors are factors that may affect their confidence to support their child's behavior change. Providers seeking to prevent childhood obesity should address parent/family behaviors as part of their obesity prevention strategies. Copyright © 2014 Academic Pediatric Association. Published by Elsevier Inc. All rights reserved.

  12. Relations between constructive peculiarities and structural behavior in Venice buildings

    Directory of Open Access Journals (Sweden)

    Doglioni, F.

    2012-12-01

    Full Text Available Here we are synthetically describing some constructive peculiarities of Venice civil buildings, analyzing the relation with the features of their structural decay and behavior in the long run. We suppose Venetian buildings, especially those parts which are conceived to suit the lagoon environment, to have undergone an evolution made of some adjustments, which were based on the observation of damages in previous buildings. That is we suppose ancient builders to rely on their awareness of the behavior of structures yet to come, and to be able to forecast it in part. This process brought some building contrivances to perfection, as exclusive and enduring features of Venice, overcoming changes in style and architectural layout, till they grew into essential elements of a whole and adaptable “device”. This writing is meant for a concise interpretation of this device, which is the result of some research works carried out at Venice IUAV University.

    En este texto, se describen sintéticamente algunas peculiaridades de la edificación residencial de Venecia, analizando su relación con el abanico de problemas estructurales que caracterizan el comportamiento estructural del edificio a lo largo del tiempo. Se aventura la hipótesis que las construcciones venecianas y, en particular, algunos de sus detalles, concebidos específicamente para la laguna donde se enclava, han sido objeto de una adaptación evolutiva a través de la observación de los problemas estructurales de los edificios precedentes. Los alarifes venecianos aprendieron a tener en cuenta el comportamiento estructural posterior del edificio, que previeron en cierta medida. Este proceso ha llevado a perfeccionar algunos detalles constructivos exclusivos de Venecia que han perdurado en el tiempo, que han resistido impertérritos a mutaciones de estilo y de configuración arquitectónica, hasta constituir elementos esenciales de un aparato indivisible y adaptable cuya interpretaci

  13. Addictive behaviors related to opioid use for chronic pain

    DEFF Research Database (Denmark)

    Højsted, Jette; Ekholm, Kim Ola Michael; Kurita, Geana Paula

    2013-01-01

    ,281 individuals were analyzed through multiple logistic regression analyses to assess the association between chronic pain (lasting ⩾6 months), opioid use, health behavior, and body mass index. Six potential addictive behaviors were identified: daily smoking; high alcohol intake; illicit drug use in the past year...

  14. Purchase decision involvement: Event management segments and related event behavior

    Science.gov (United States)

    Rodney B. Warnick; David C. Bojanic

    2012-01-01

    The goal of this research was to examine the relationships between different levels of event purchase decision involvement (PDI) segments and their respective event behaviors (e.g., expenditures, travel behavior, event consumption and satisfaction). The specific purpose was to answer two major research questions: 1) Can PDI identify different levels or segments of...

  15. Stress among Graduate Students in Relation to Health Behaviors

    Science.gov (United States)

    van Berkel, Kelly; Reeves, Brenda

    2017-01-01

    Problem: While stress is universal for graduate students, the difference in terms of stress symptoms and the effects on health behavior is how students cope. While numerous research studies have linked stress and negative health behaviors, few studies have objectively assessed these variables. Purpose: Utilize current health and fitness technology…

  16. Children's and Their Friends' Moral Reasoning: Relations with Aggressive Behavior

    Science.gov (United States)

    Gasser, Luciano; Malti, Tina

    2012-01-01

    Friends' moral characteristics such as their moral reasoning represent an important social contextual factor for children's behavioral socialization. Guided by this assumption, we compared the effects of children's and friends' moral reasoning on their aggressive behavior in a low-risk sample of elementary school children. Peer nominations and…

  17. Determinants of Risky Sexual Behavior, Relation between HIV Risk ...

    African Journals Online (AJOL)

    Science, Technology and Arts Research Journal ... Partial correlation and linear regression was used to assess the applicability of Theory of Planned Behavior model in predicting intention to use condom and ... In this study, Theory of Planned Behavior explained 39.3% of variances in intention to consistent condom use.

  18. Industrial Buying Behavior Related to Human Resource Consulting Services

    DEFF Research Database (Denmark)

    Hollensen, Svend; Grünbaum, Niels Nolsøe; Andresen, Marc

    2013-01-01

    Early B2B buying-behavior literature strongly emphasizes the rational aspects of buying behavior in B2B services. Based on a comprehensive exploratory study of Danish companies’ purchases of HR consulting services, the authors provide insights into the factors that determine how Danish companies ...

  19. Carbon-Based Materials for Lithium-Ion Batteries, Electrochemical Capacitors, and Their Hybrid Devices.

    Science.gov (United States)

    Yao, Fei; Pham, Duy Tho; Lee, Young Hee

    2015-07-20

    A rapidly developing market for portable electronic devices and hybrid electrical vehicles requires an urgent supply of mature energy-storage systems. As a result, lithium-ion batteries and electrochemical capacitors have lately attracted broad attention. Nevertheless, it is well known that both devices have their own drawbacks. With the fast development of nanoscience and nanotechnology, various structures and materials have been proposed to overcome the deficiencies of both devices to improve their electrochemical performance further. In this Review, electrochemical storage mechanisms based on carbon materials for both lithium-ion batteries and electrochemical capacitors are introduced. Non-faradic processes (electric double-layer capacitance) and faradic reactions (pseudocapacitance and intercalation) are generally explained. Electrochemical performance based on different types of electrolytes is briefly reviewed. Furthermore, impedance behavior based on Nyquist plots is discussed. We demonstrate the influence of cell conductivity, electrode/electrolyte interface, and ion diffusion on impedance performance. We illustrate that relaxation time, which is closely related to ion diffusion, can be extracted from Nyquist plots and compared between lithium-ion batteries and electrochemical capacitors. Finally, recent progress in the design of anodes for lithium-ion batteries, electrochemical capacitors, and their hybrid devices based on carbonaceous materials are reviewed. Challenges and future perspectives are further discussed. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Electrochemical impedance characterization of FeSn2 electrodes for Li-ion batteries

    International Nuclear Information System (INIS)

    Chamas, M.; Lippens, P-E.; Jumas, J-C.; Hassoun, J.; Panero, S.; Scrosati, B.

    2011-01-01

    Highlights: → In this paper we study a tin based, FeSn 2 , high capacity lithium-alloying electrode. → The electrochemical performance of this electrode in lithium batteries is remarkably influenced by the current rate. → This aspect is investigated by electrochemical techniques such as galvanostatic cycling and impedance spectroscopy. → The results demonstrated that the good electrochemical behavior of the electrode at the higher currents is due to the formation of a stable solid electrolyte interphase (SEI) film. - Abstract: This work reports the electrochemical characterization of a micro-scale FeSn 2 electrode in a lithium battery. The electrode is proposed as anode material for advanced lithium ion batteries due to its characteristics of high capacity (500 mAh g -1 ) and low working voltage (0.6 V vs. Li). The electrochemical alloying process is studied by cyclic voltammetry and galvanostatic cycling while the interfacial properties are investigated by electrochemical impedance spectroscopy. The impedance measurements in combination with the galvanostatic cycling tests reveal relatively low overall impedance values and good electrochemical performance for the electrode, both in terms of delivered capacity and cycling stability, even at the higher C-rate regimes.

  1. The relations among child negative interactive behavior, child temperament, and maternal behavior

    NARCIS (Netherlands)

    Szabo, Nora; Dekovic, Maja; van Aken, Chantal; Verhoeven, Marjolein; van Aken, Marcel A.G.; Junger, Marianne

    2008-01-01

    Negative behavior toward the mother during toddlerhood might be a marker of increased risk for maladjustment. The aim of the present study was to examine the possible antecedents of toddler boys’ negative behavior observed in interaction with the mother: child temperament, and maternal behavior

  2. Association of Active Play-Related Parenting Behaviors, Orientations, and Practices with Preschool Sedentary Behavior

    Science.gov (United States)

    Loprinzi, Paul D.; Cardinal, Bradley J.; Kane, Christy; Lee, Hyo; Beets, Michael W.

    2014-01-01

    Background: Parents' behaviors, practices, beliefs, and attitudes greatly influence children's active play behavior; however, little research has examined these parental influences on preschool children's sedentary behavior (SB). Purpose: The purpose of this study was to examine the association between parental influences on preschool SB. Methods:…

  3. Treatment Effects of a Primary Care Intervention on Parenting Behaviors: Sometimes It's Relative.

    Science.gov (United States)

    Shaffer, Anne; Lindhiem, Oliver; Kolko, David

    2017-04-01

    The goal of this brief report is to demonstrate the utility of quantifying parental discipline practices as relative frequencies in measuring changes in parenting behavior and relations to child behavior following intervention. We explored comparisons across methodological approaches of assessing parenting behavior via absolute and relative frequencies in measuring improvements in parent-reported disciplinary practices (increases in positive parenting practices in response to child behavior; decreases in inconsistent discipline and use of corporal punishment) and child behavior problems. The current study was conducted as part of a larger clinical trial to evaluate the efficacy of a collaborative care intervention for behavior problems, ADHD, and anxiety in pediatric primary care practices (Doctor Office Collaborative Care; DOCC). Participants were 321 parent-child dyads (M child age = 8.00, 65 % male children) from eight pediatric practices that were cluster randomized to DOCC or enhanced usual care (EUC). Parents reported on their own discipline behaviors and child behavior problems. While treatment-related decreases in negative parenting were found using both the absolute and relative frequencies of parenting behaviors, results were different for positive parenting behaviors, which showed decreases when measured as absolute frequencies but increases when measured as relative frequencies. In addition, positive parenting was negatively correlated with child behavior problems when using relative frequencies, but not absolute frequencies, and relative frequencies of positive parenting mediated relations between treatment condition and outcomes. Our findings indicate that the methods used to measure treatment-related change warrant careful consideration.

  4. Asperger syndrome related suicidal behavior: two case studies

    Directory of Open Access Journals (Sweden)

    Kocourkova J

    2013-11-01

    Full Text Available Jana Kocourkova, Iva Dudova, Jiri Koutek Department of Child Psychiatry, Charles University Second Faculty of Medicine, University Hospital Motol, Prague, Czech Republic Abstract: Asperger syndrome hinders adaptation to developmental challenges during childhood and adolescence, particularly with regard to interpersonal relationships. Individuals with Asperger syndrome display lack of empathy and limited ability to understand social and emotional exchanges with other people. Individuals with Asperger syndrome are significantly exposed to the risk of suicidal behavior, especially during adolescence. The authors describe cases of suicidal behavior in two adolescent boys with Asperger syndrome. Keywords: Asperger syndrome, suicidal behavior, adolescence

  5. Competitiveness as a moderator of the relation between appearance-related factors and disordered eating behaviors.

    Science.gov (United States)

    Schleien, Jenna L; Bardone-Cone, Anna M

    2016-06-01

    The present study examined competitiveness as a moderator of the relationships between appearance-related factors (i.e., thin-ideal internalization, appearance contingent self-worth) and disordered eating behaviors (i.e., dieting, excessive exercise). Participants were 441 undergraduate females for cross-sectional analyses, with 237 also contributing data longitudinally, 1 year later. Results showed that, in a model including thin-ideal internalization and appearance contingent self-worth and their interactions with competitiveness, thin-ideal internalization (but not appearance contingent self-worth) interacted with competitiveness to identify concurrent levels of both dieting and excessive exercise. Individuals high in both thin-ideal internalization and competitiveness exhibited the highest levels of concurrent dieting and excessive exercise. After controlling for baseline levels of the dependent variables, neither appearance-related factor interacted with competitiveness to predict dieting or excessive exercise. These findings suggest that individuals who are both competitive and accept and strive to achieve the thin ideal may be at risk for disordered eating behaviors. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Obesity-related behaviors among poor adolescents and young adults: Is social position associated with risk behaviors?

    Directory of Open Access Journals (Sweden)

    Miranda Lucia Ritterman Weintraub

    2015-10-01

    Full Text Available This cross-sectional study examines multiple dimensions of social position in relation to obesity-related behaviors in an adolescent and young adult population. In addition to using conventional measures of social position, including parental education and household expenditures, we explore the usefulness of three youth-specific measures of social position—community and society subjective social status and school dropout status. Data is taken from a 2004 house-to-house survey of urban households within the bottom 20th percentile of income distribution within seven states in Mexico. A total of 5,321 Mexican adolescents, aged 12-22 years, provided information on obesity-related behaviors (e.g. diet, physical activity, sedentary behavior and indicators of subjective and objective social position. A parent in each household provided information on socioeconomic status of the parent and household. Ordinal logistic regressions are used to estimate the associations of parental, household and adolescent indicators of social position and obesity-related risk behaviors. Those adolescents with the highest odds of adopting obesity risk behaviors were the ones who perceived themselves as lower in social status in reference to their peer community and those who had dropped out of school. We found no significant associations between parental education or household expenditures and obesity-related risk behaviors. Immediate social factors in adolescents' lives may have a strong influence on their health-related behaviors. This study provides evidence for the usefulness of two particular measures, both of which are youth-specific. Adolescents and young adults who have dropped out of school and those with lower perceived relative social position within their community are more likely to be at-risk for obesity-related behaviors than those with higher relative social position. We conclude that youth-specific measures may be important in identifying the most at

  7. Antisocial behavior in adolescence: Typology and relation to family context

    Czech Academy of Sciences Publication Activity Database

    Sobotková, Veronika; Blatný, Marek; Jelínek, Martin; Hrdlička, M.

    2013-01-01

    Roč. 33, č. 8 (2013), s. 1091-1115 ISSN 0272-4316 Institutional support: RVO:68081740 Keywords : family * antisocial behavior * typology * adolescence Subject RIV: AN - Psychology Impact factor: 1.200, year: 2013

  8. A case report of suicidal behavior related to subclinical hyperthyroidism

    Directory of Open Access Journals (Sweden)

    Joo SH

    2014-04-01

    Full Text Available Soo-Hyun Joo, Jong-Hyun Jeong, Seung-Chul HongDepartment of Psychiatry, St Vincent's Hospital, College of Medicine, The Catholic University of Korea, Suwon, KoreaAbstract: Abnormalities in thyroid function are associated with many psychiatric symptoms. We present a report of a 15-year-old girl who was admitted to the psychiatry inpatient unit with symptoms of suicidal behavior, irritability, and impulsivity. One year previously, she had become more short-tempered, and had started to cut her wrists impulsively. Laboratory tests revealed subclinical hyperthyroidism. She was treated with anxiolytic and antithyroid drugs, and her suicidal ideation and irritability resolved. This case demonstrates that subclinical hyperthyroidism can be associated with suicidal behavior as well as overt hyperthyroidism. Early intervention is required to prevent suicidal behavior in patients with subclinical hyperthyroidism.Keywords: suicidal behavior, subclinical hyperthyroidism, anxiolytics

  9. The associations between cigarette smoking and health-related behaviors among Chinese school-aged adolescents

    Directory of Open Access Journals (Sweden)

    Meng Wang

    2017-06-01

    The results suggested that cigarette smoking was associated with a cluster of health-related behaviors in adolescents, which should be considered in health promotion interventions to target multiple health behaviors.

  10. Brain Regions Related to Impulsivity Mediate the Effects of Early Adversity on Antisocial Behavior

    NARCIS (Netherlands)

    Mackey, Scott; Chaarani, Bader; Kan, Kees Jan; Spechler, Philip A.; Orr, Catherine; Banaschewski, Tobias; Barker, Gareth; Bokde, Arun L.W.; Bromberg, Uli; Büchel, Christian; Cattrell, Anna; Conrod, Patricia J.; Desrivières, Sylvane; Flor, Herta; Frouin, Vincent; Gallinat, Jürgen; Gowland, Penny; Heinz, Andreas; Ittermann, Bernd; Paillère Martinot, Marie Laure; Artiges, Eric; Nees, Frauke; Papadopoulos-Orfanos, Dimitri; Poustka, Luise; Smolka, Michael N.; Jurk, Sarah; Walter, Henrik; Whelan, Robert; Schumann, Gunter; Althoff, Robert R.; Garavan, Hugh

    2017-01-01

    Background Individual differences in impulsivity and early adversity are known to be strong predictors of adolescent antisocial behavior. However, the neurobiological bases of impulsivity and their relation to antisocial behavior and adversity are poorly understood. Methods Impulsivity was estimated

  11. Predicting personality traits related to consumer behavior using SNS analysis

    Science.gov (United States)

    Baik, Jongbum; Lee, Kangbok; Lee, Soowon; Kim, Yongbum; Choi, Jayoung

    2016-07-01

    Modeling a user profile is one of the important factors for devising a personalized recommendation. The traditional approach for modeling a user profile in computer science is to collect and generalize the user's buying behavior or preference history, generated from the user's interactions with recommender systems. According to consumer behavior research, however, internal factors such as personality traits influence a consumer's buying behavior. Existing studies have tried to adapt the Big 5 personality traits to personalized recommendations. However, although studies have shown that these traits can be useful to some extent for personalized recommendation, the causal relationship between the Big 5 personality traits and the buying behaviors of actual consumers has not been validated. In this paper, we propose a novel method for predicting the four personality traits-Extroversion, Public Self-consciousness, Desire for Uniqueness, and Self-esteem-that correlate with buying behaviors. The proposed method automatically constructs a user-personality-traits prediction model for each user by analyzing the user behavior on a social networking service. The experimental results from an analysis of the collected Facebook data show that the proposed method can predict user-personality traits with greater precision than methods that use the variables proposed in previous studies.

  12. Electrochemistry of potentially bioreductive alkylating quinones : Part 1. Electrochemical properties of relatively simple quinones, as model compounds of mitomycin- and aziridinylquinone-type antitumour agents

    NARCIS (Netherlands)

    Driebergen, R.J.; den Hartigh, J.; Holthuis, J.J.M.; Hulshoff, A.; van Oort, W.J.; Postma kelder, S.J.; Verboom, Willem; Reinhoudt, David; Bos, M.; van der Linden, W.E.

    1990-01-01

    The influence of methyl-, hydroxy and amino substituents on the electrochemical behaviour of simple 1,4-naphtho-and 1,4-benzoquinones, model compounds of many quinoid antitumour agents, in aqueous media was studied. Significant changes in electrochemical behaviour were observed, potentially the

  13. Modeling Structural, Dyadic, and Individual Factors: The Inclusion and Exclusion Model of HIV Related Behavior

    OpenAIRE

    Albarracin, Dolores; Tannenbaum, Melanie B.; Glasman, Laura R.; Rothman, Alexander J.

    2010-01-01

    Changing HIV-related behaviors requires addressing the individual, dyadic, and structural influences that shape them. This supplement of AIDS & Behavior presents frameworks that integrate these three influences on behavior. Concepts from these frameworks were selected to model the processes by which structural factors affect individual HIV-related behavior. In the Inclusion/Exclusion Model, material and symbolic inclusions and exclusions (sharing versus denying resources) regulate individuals...

  14. Predictors of Prosthodontic Treatment-Related Behavior Using the Theory of Planned Behavior Framework.

    Science.gov (United States)

    Vieira, Antonio Helio; Castro e Silva, Donizete; Nogueira, Túlio Eduardo; Leles, Cláudio Rodrigues

    2016-01-01

    The Theory of Planned Behavior (TPB) was used to assess subjects' intentions and behavior to predict willingness to undergo prosthodontic care. A questionnaire was administered to 225 adults with history of teeth loss who currently were not under prosthodontic treatment. The questionnaire comprised TPB components (attitude toward behaviour [ATB], subjective norm [SN], and perceived behavioral control [PBC]) containing items with potential influence on the intentions and behavior of individuals toward prosthodontic care. Clinical and socioeconomic data were also assessed. A path regression model was constructed explaining two dependent variables simultaneously: one explained the influence of PBC on intention (R2=0.04) and another explained the influence of dental arch, position of lost teeth, socioeconomic status, and PBC on behavior (R2=0.31). It was concluded that PBC was a relevant TPB component that encompasses perception of costs, opportunity cost, perceived need, and access to dental care. Clinical and socioeconomic factors were also major determinants of behavior toward prosthodontic treatment.

  15. Sex-Related Online Behaviors, Perceived Peer Norms and Adolescents’ Experience with Sexual Behavior: Testing an Integrative Model

    Science.gov (United States)

    Doornwaard, Suzan M.; ter Bogt, Tom F. M.; Reitz, Ellen; van den Eijnden, Regina J. J. M.

    2015-01-01

    Research on the role of sex-related Internet use in adolescents’ sexual development has often isolated the Internet and online behaviors from other, offline influencing factors in adolescents’ lives, such as processes in the peer domain. The aim of this study was to test an integrative model explaining how receptive (i.e., use of sexually explicit Internet material [SEIM]) and interactive (i.e., use of social networking sites [SNS]) sex-related online behaviors interrelate with perceived peer norms in predicting adolescents’ experience with sexual behavior. Structural equation modeling on longitudinal data from 1,132 Dutch adolescents (Mage T1 = 13.95; range 11-17; 52.7% boys) demonstrated concurrent, direct, and indirect effects between sex-related online behaviors, perceived peer norms, and experience with sexual behavior. SEIM use (among boys) and SNS use (among boys and girls) predicted increases in adolescents’ perceptions of peer approval of sexual behavior and/or in their estimates of the numbers of sexually active peers. These perceptions, in turn, predicted increases in adolescents’ level of experience with sexual behavior at the end of the study. Boys’ SNS use also directly predicted increased levels of experience with sexual behavior. These findings highlight the need for multisystemic research and intervention development to promote adolescents’ sexual health. PMID:26086606

  16. Electrochemical noise of the erosion-corrosion of copper in relation with its hydrodynamic parameters; Ruido electroquimico de la erosion-corrosion en cobre: su relacion con los parametros hidrodinamicos

    Energy Technology Data Exchange (ETDEWEB)

    Castaneda, I.; Romero, M.; Malo, J.M.; Uruchurtu, J.

    2010-07-01

    This work presents the electrochemical noise results obtained of the surface degradation on copper, due to erosion corrosion phenomena, which were a function of the hydrodynamic parameters of the system (fluid movement). A modified rotating cylinder (RC) comprising three ring electrodes under two rotating speeds (880 and 1750 rpm with a Reynolds numbers 1486 Re and 2972 Re, respectively) were used. Characteristic electrochemical noise spectra as a function of the hydrodynamic parameters were found, as well as surface attack intensities the noise signal. An increase and a more uniform attack due to particle impact was related to larger particle size and lesser erosion corrosion intensity, in the form of more localized attack over the surface, was obtained for smaller ones. Erosion corrosion attack presents characteristic electrochemical current and potential noise signals, according to the laminar or transitional turbulent regime and particle size added. (Author).

  17. Age-Related Differences in Judgments of Inappropriate Behavior are Related to Humor Style Preferences

    Science.gov (United States)

    Stanley, Jennifer Tehan; Lohani, Monika; Isaacowitz, Derek M.

    2014-01-01

    Identifying social gaffes is important for maintaining relationships. Older adults are less able than young to discriminate between socially appropriate and inappropriate behavior in video clips. One open question is how these social appropriateness ratings relate to potential age differences in the perception of what is actually funny or not. In the present study, young, middle-aged, and older adults were equally able to discriminate between appropriate and inappropriate social behavior in a diverse set of clips relevant to both age groups. However, young and middle-aged adults rated the gaffe clips as funnier than control clips and young adults smiled more during the inappropriate clips than the control clips. Older adults did not show this pattern, suggesting that they did not find the inappropriate clips funny. Additionally, young adults endorsed a more aggressive humor style than middle-aged and older adults and aggressive humor style endorsement mediated age differences in social appropriateness ratings. Results are discussed in terms of possible mechanisms such as cohort differences in humor and developmental prioritization of certain humor styles, as well as the importance of investigating age differences in both abilities and preferences. PMID:25244473

  18. Behavior of the monophosphate tungsten bronzes (PO2)4(WO3)2m (m = 7 and 8) in the course of electrochemical lithium insertion

    International Nuclear Information System (INIS)

    Martinez-de la Cruz, A.; Longoria Rodriguez, F.E.; Gonzalez, Lucy T.; Torres-Martinez, Leticia M.

    2007-01-01

    The electrochemical lithium insertion process has been studied in the family of monophosphate tungsten bronzes (PO 2 ) 4 (WO 3 ) 2m , where m = 7 and 8. Structural changes in the pristine oxides were followed as lithium insertion proceeded. Through potentiostatic intermittent technique the different processes which take place in the cathode during the discharge of the cell were analyzed. The nature of the bronzes Li x (PO 2 ) 4 (WO 3 ) 2m formed was determined by in situ X-ray diffraction experiments. These results have allowed establishing a correlation with the reversible/irreversible processes detected during the electrochemical lithium insertion

  19. Educating dental students about diet-related behavior change: does experiential learning work?

    Science.gov (United States)

    Taylor, George W; Stumpos, Madelyn L; Kerschbaum, Wendy; Inglehart, Marita Rohr

    2014-01-01

    The objective of this study was to explore whether an experiential exercise in a nutrition class would a) increase dental students' motivation to change their own diet-related behavior, b) improve their understanding of theoretical concepts related to behavior change, and c) improve their attitudes towards educating their patients about diet-related behavior. Data were collected from 218 senior dental students in one dental school (2010: 106; 2011: 112) during their nutrition class. The students agreed at the beginning that it was important to change their own diet-related behavior. After one week, the majority agreed that they had changed how they felt and thought about the targeted behavior and what they actually did. After three weeks and at the end of the term, they rated the exercise as helpful for gaining a better understanding of health education theories. The majority indicated that the exercise had helped them understand the difficulty of diet-related behavior change and that it had increased their interest in helping patients change their diet-related behavior. In conclusion, this study suggests that experiential learning about diet-related behavior change is likely to affect students' own behavior positively and to result in increased understanding of behavior change theories and positive behavioral intentions concerning future health education efforts with patients.

  20. Modeling structural, dyadic, and individual factors: the inclusion and exclusion model of HIV related behavior.

    Science.gov (United States)

    Albarracin, Dolores; Tannenbaum, Melanie B; Glasman, Laura R; Rothman, Alexander J

    2010-12-01

    Changing HIV-related behaviors requires addressing the individual, dyadic, and structural influences that shape them. This supplement of AIDS & Behavior presents frameworks that integrate these three influences on behavior. Concepts from these frameworks were selected to model the processes by which structural factors affect individual HIV-related behavior. In the Inclusion/Exclusion Model, material and symbolic inclusions and exclusions (sharing versus denying resources) regulate individuals' ability and motivation to detect, prevent, and treat HIV. Structural interventions create inclusions that increase one's ability or motivation to perform these behaviors or exclusions that hinder one's ability or motivation to execute counterproductive behaviors. The need to expand research regarding multilevel influences on HIV-related behavior is also discussed, particularly concerning further understanding of sustained behavior change and effective dissemination of evidence-based intervention strategies.

  1. Industrial Buying Behavior Related to Human Resource Consulting Services

    DEFF Research Database (Denmark)

    Grünbaum, Niels Nolsøe; Hollensen, Svend; Kahle, Lynn

    2013-01-01

    The purpose of this article is to extend the understanding of the industrial buying process in connection with purchasing professional business (B2B) services, specifically human resource (HR) consulting services. Early B2B buying-behavior literature strongly emphasizes the rational aspects...... of buying behavior in B2B services. Based on a comprehensive exploratory study of Danish companies’ purchases of HR consulting services, the authors provide insights into the factors that determine how Danish companies choose a consulting services supplier. Five hypotheses are developed based...

  2. Clinical Considerations Related to the Behavioral Manifestations of Child Maltreatment.

    Science.gov (United States)

    Sege, Robert D; Amaya-Jackson, Lisa

    2017-04-01

    Children who have suffered early abuse or neglect may later present with significant health and behavior problems that may persist long after the abusive or neglectful environment has been remediated. Neurobiological research suggests that early maltreatment may result in an altered psychological and physiologic response to stressful stimuli, a response that deleteriously affects the child's subsequent development. Pediatricians can assist caregivers by helping them recognize the abused or neglected child's emotional and behavioral responses associated with child maltreatment and guide them in the use of positive parenting strategies, referring the children and families to evidence-based therapeutic treatment and mobilizing available community resources. Copyright © 2017 by the American Academy of Pediatrics.

  3. Electrochemical depth profiling of multilayer metallic structures: An aluminum brazing sheet

    International Nuclear Information System (INIS)

    Afshar, F. Norouzi; Ambat, R.; Kwakernaak, C.; Wit, J.H.W. de; Mol, J.M.C.; Terryn, H.

    2012-01-01

    Highlights: ► Localized electrochemical cell and glow discharge optical emission spectrometry were used. ► An electrochemical depth profile of an aluminum brazing sheet was obtained. ► The electrochemical responses were correlated to the microstructural features. - Abstract: Combinatory localized electrochemical cell and glow discharge optical emission spectrometry (GDOES) measurements were performed to obtain a thorough in depth electrochemical characterization of an aluminum brazing sheet. By defining electrochemical criteria i.e. breakdown potential, corrosion potential, cathodic and anodic reactivities, and tracking their changes as a function of depth, the evolution of electrochemical responses through out the material thickness were analyzed and correlated to the corresponding microstructural features. Polarization curves in 1 wt% NaCl solution at pH 2.8 were obtained at different depths from the surface using controlled sputtering in a glow discharge optical emission spectrometer as a sample preparation technique. The anodic and cathodic reactivity of the top surface areas were significantly higher than that of the bulk, thus indicating these areas to be more susceptible to localized attack. Consistent with this, optical microscopy and scanning electron microscope analysis revealed a relatively high density of fine intermetallic and silicon particles at these areas. The corrosion mechanism of the top layers was identified to be intergranular and pitting corrosion, while lower sensitivity to these localized attacks were detected toward the brazing sheet core. The results highlight the successful application of the electrochemical depth profiling approach in prediction of the corrosion behavior of the aluminum brazing sheet and the importance of the electrochemical activity of the outer 10 μm in controlling the corrosion performance of the aluminum brazing sheet.

  4. Physical and relational bullying and victimization: Differential relations with adolescent dating and sexual behavior.

    Science.gov (United States)

    Dane, Andrew V; Marini, Zopito A; Volk, Anthony A; Vaillancourt, Tracy

    2017-04-01

    Taking an evolutionary psychological perspective, we investigated whether involvement in bullying as a perpetrator or victim was more likely if adolescents reported having more dating and sexual partners than their peers, an indication of greater engagement in competition for mates. A total of 334 adolescents (173 boys, 160 girls) between the ages of 12 and 16 years (M = 13.6, SD = 1.3), recruited from community youth organizations, completed self-report measures of physical and relational bullying and victimization, as well as dating and sexual behavior. As predicted, pure physical bullying was positively associated with the number of dating and sexual partners, primarily for adolescent boys. Adolescent girls with more dating partners had greater odds of being relational bully-victims, in line with predictions. Finally, adolescent girls with more sexual partners were at greater risk of being physically victimized by peers, and greater involvement with dating and sexual partners was associated with higher odds of being a physical bully-victim. Results are discussed with respect to evolutionary theory and research in which adolescent boys may display strength and athleticism through physical bullying to facilitate intersexual selection, whereas relational bullying may be employed as a strategy to engage in intrasexual competition with rivals for mates. Aggr. Behav. 43:111-122, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  5. Self-Regulatory Processes Mediate the Intention-Behavior Relation for Adherence and Exercise Behaviors

    NARCIS (Netherlands)

    Bruin, de M.; Sheeran, P.; Kok, G.; Hiemstra, A.; Prins, J.M.; Hospers, H.J.; Breukelen, G.J.P.

    2012-01-01

    Objectives: Understanding the gap between people's intentions and actual health behavior is an important issue in health psychology. Our aim in this study was to investigate whether self-regulatory processes (monitoring goal progress and responding to discrepancies) mediate the intention-behavior

  6. Forming Attitudes That Predict Future Behavior: A Meta-Analysis of the Attitude–Behavior Relation

    Science.gov (United States)

    Glasman, Laura R.; Albarracín, Dolores

    2016-01-01

    A meta-analysis (k of conditions = 128; N = 4,598) examined the influence of factors present at the time an attitude is formed on the degree to which this attitude guides future behavior. The findings indicated that attitudes correlated with a future behavior more strongly when they were easy to recall (accessible) and stable over time. Because of increased accessibility, attitudes more strongly predicted future behavior when participants had direct experience with the attitude object and reported their attitudes frequently. Because of the resulting attitude stability, the attitude–behavior association was strongest when attitudes were confident, when participants formed their attitude on the basis of behavior-relevant information, and when they received or were induced to think about one- rather than two-sided information about the attitude object. PMID:16910754

  7. Antisocial Behavior in Adolescence: Typology and Relation to Family Context

    Science.gov (United States)

    Sobotková, Veronika; Blatný, Marek; Jelínek, Martin; Hrdlicka, Michal

    2013-01-01

    The study deals with the relationship between antisocial behavior in early adolescence and family environment. Sample consisted of 2,856 adolescents (53% girls, mean age 13.5 years, SD = 1.1) from urban areas in the Czech Republic. The Social and Health Assessment (SAHA), a school survey, was used to measure sociodemographic characteristics of the…

  8. Laboratory Measured Behavioral Impulsivity Relates to Suicide Attempt History

    Science.gov (United States)

    Dougherty, Donald M.; Mathias, Charles W.; Marsh, Dawn M.; Papageorgiou, T. Dorina; Swann, Alan C.; Moeller, F. Gerard

    2004-01-01

    The purpose of this study was to examine the relationship between laboratory behavioral measured impulsivity (using the Immediate and Delayed Memory Tasks) and suicidal attempt histories. Three groups of adults were recruited, those with either: no previous suicide attempts (Control, n = 20), only a single suicide attempt (Single, n = 20), or…

  9. Friendship Expectations and Children's Friendship-Related Behavior and Adjustment

    Science.gov (United States)

    MacEvoy, Julie Paquette; Papadakis, Alison A.; Fedigan, Shea K.; Ash, Sarah E.

    2016-01-01

    Although relationship expectations are thought to influence all social interactions, little is known about the function of children's friendship expectations. This study examined the associations among children's friendship expectations and their behavior within their friendships, their friendship adjustment, and their socioemotional functioning.…

  10. Explicit- and Implicit Bullying Attitudes in Relation to Bullying Behavior

    NARCIS (Netherlands)

    Goethem, A.A.J. van; Scholte, R.H.J.; Wiers, R.W.H.J.

    2010-01-01

    The main aim of this study was to examine whether an assessment of implicit bullying attitudes could add to the prediction of bullying behavior after controlling for explicit bullying attitudes. Primary school children (112 boys and 125 girls, M age = 11 years, 5 months) completed two newly

  11. Explicit- and implicit bullying attitudes in relation to bullying behavior

    NARCIS (Netherlands)

    van Goethem, A.A.J.; Scholte, R.H.J.; Wiers, R.W.

    2010-01-01

    The main aim of this study was to examine whether an assessment of implicit bullying attitudes could add to the prediction of bullying behavior after controlling for explicit bullying attitudes. Primary school children (112 boys and 125 girls, M age = 11 years, 5 months) completed two newly

  12. Leadership Behaviors and Its Relation with Principals' Management Experience

    Science.gov (United States)

    Mehdinezhad, Vali; Sardarzahi, Zaid

    2016-01-01

    This paper aims at studying the leadership behaviors reported by principals and observed by teachers and its relationship with management experience of principals. A quantitative method was used in this study. The target population included all principals and teachers of guidance schools and high schools in the Dashtiari District, Iran. A sample…

  13. Cognitive ability and health-related behaviors during adolescence

    DEFF Research Database (Denmark)

    Ciarrochi, Joseph; Heaven, Patrick C L; Skinner, Timothy

    2012-01-01

    Longitudinal research on the links between intelligence and health behaviors among adolescents is rare. We report longitudinal data in which we assessed the relationships between intelligence as assessed in Grade 7 and consequential health outcomes in Grade 11. The mean age of respondents (N=420;...

  14. AgCuO2: Preparationand Electrochemical Behaviors in Alkaline Electrolytes%AgCuO2:制备及其在碱性溶液中的电化学行为

    Institute of Scientific and Technical Information of China (English)

    张婷锦; 张校刚; 胡风平

    2005-01-01

    The silver cuprate AgCuO2 powder was prepared by a chemical co-precipitation method and characterized by XRD, SEM and TEM techniques. The electrochemical behaviors of AgCuO2 electrodes and AgCuO2 modified by sulfur were studied by means of galvanostatic discharge and line sweep voltammetry experiments. The resuits indicated that the specific capacity of AgCuO2 could reach 422.32 mAh·g-1 at middle discharge rate and the addition of sulfur could significantly improve the discharge performance of AgCuO2. The mechanism for this modified effect was also discussed.

  15. Characterizing users of new psychoactive substances using psychometric scales for risk-related behavior

    NARCIS (Netherlands)

    Vreeker, Annabel; van der Burg, Babette G.; van Laar, Margriet; Brunt, Tibor M.

    2017-01-01

    Studies investigating risk-related behavior in relation to new psychoactive substance (NPS) use are sparse. The current study investigated characteristics of NPS users by comparing risk-related behavior of NPS users to that of illicit drugs (ID) users and licit substances users and non-users (NLC)

  16. Fat- and Fiber-Related Diet Behavior among Type 2 Diabetes Patients from Distinct Regions

    Czech Academy of Sciences Publication Activity Database

    Hendrychová, T.; Vytřísalová, M.; Alwarafi, A.; Duintjer Tebbens, Jurjen; Vaňkátová, H.; Leal, S.; Kuběna, A.A.; Šmahelová, A.; Vlček, J.

    2015-01-01

    Roč. 9, Article number A38 (2015), s. 319-325 ISSN 1177-889X R&D Projects: GA ČR GA13-06684S Grant - others:SVV UK(CZ) 260 066 Institutional support: RVO:67985807 Keywords : type 2 diabetes mellitus * fat-related behavior * fiber-related behavior * Fat- and Fiber-related Diet Behavior Questionnaire * geographical difference Subject RIV: FR - Pharmacology ; Medidal Chemistry Impact factor: 1.718, year: 2015

  17. Mathematics Achievement and Anxiety and Their Relation to Internalizing and Externalizing Behaviors

    Science.gov (United States)

    Wu, Sarah S.; Willcutt, Erik G.; Escovar, Emily; Menon, Vinod

    2014-01-01

    Although behavioral difficulties are well documented in reading disabilities, little is known about the relationship between math ability and internalizing and externalizing behaviors. Here, we use standardized measures to investigate the relation among early math ability, math anxiety, and internalizing and externalizing behaviors in a group of…

  18. Hydrogen storage material, electrochemically active material, electrochemical cell and electronic equipment

    NARCIS (Netherlands)

    2008-01-01

    The invention relates to a hydrogen storage material comprising an alloy of magnesium. The invention further relates to an electrochemically active material and an electrochemical cell provided with at least one electrode comprising such a hydrogen storage material. Also, the invention relates to

  19. A case report of suicidal behavior related to subclinical hyperthyroidism

    OpenAIRE

    Jeong, Jong-Hyun; Joo,Soo-Hyun; Hong,Seung-Chul

    2014-01-01

    Soo-Hyun Joo, Jong-Hyun Jeong, Seung-Chul HongDepartment of Psychiatry, St Vincent's Hospital, College of Medicine, The Catholic University of Korea, Suwon, KoreaAbstract: Abnormalities in thyroid function are associated with many psychiatric symptoms. We present a report of a 15-year-old girl who was admitted to the psychiatry inpatient unit with symptoms of suicidal behavior, irritability, and impulsivity. One year previously, she had become more short-tempered, and had started to c...

  20. Workplace exercise for changing health behavior related to physical activity.

    Science.gov (United States)

    Grande, Antonio José; Cieslak, Fabrício; Silva, Valter

    2015-01-01

    Physical Activity in the workplace has received special attention from researchers who are looking to promote lifelong health and well-being. The workplace is being investigated as a possible place to assess and create strategies to help people to become healthier. The transtheoretical model and stages of change has been adapted as a tool to assess the stages of behavioral change towards exercising. To assess the change in health behavior following a three-month exercise program based in the workplace. A quasi-experimental study design was used in which 165 employees participated in the study. An intervention program of workplace exercise was applied for three months. Participants were assessed through the transtheoretical model and stages of change questionnaire before and after intervention to understand changes in their position on the behavioral change continuum. The number of employees who were physically active increased after the workplace exercise intervention (13.9% , 95% CI 9.5 to 20.1; P = 0.009). There was a significant decrease in the proportion of employees in the pre-contemplation stage (-6.1% , 95% CI 3.3 to 10.8; P = 0.045) and contemplation stage (-11.5% , 95% CI 7.5 to 17.3; P = 0.017), and a significant increase in the action stage (10.9% , 95% CI 7.0 to 16.6; P = 0.003). Engaging in workplace exercise has a significant positive effect on health behavior and willingness to become more physically active.

  1. The child play behavior and activity questionnaire: a parent-report measure of childhood gender-related behavior in China.

    Science.gov (United States)

    Yu, Lu; Winter, Sam; Xie, Dong

    2010-06-01

    Boys and girls establish relatively stable gender stereotyped behavior patterns by middle childhood. Parent-report questionnaires measuring children's gender-related behavior enable researchers to conduct large-scale screenings of community samples of children. For school-aged children, two parent-report instruments, the Child Game Participation Questionnaire (CGPQ) and the Child Behavior and Attitude Questionnaire (CBAQ), have long been used for measuring children's sex-dimorphic behaviors in Western societies, but few studies have been conducted using these measures for Chinese populations. The current study aimed to empirically examine and modify the two instruments for their applications to Chinese society. Parents of 486 Chinese boys and 417 Chinese girls (6-12 years old) completed a questionnaire comprising items from the CGPQ and CBAQ, and an additional 14 items specifically related to Chinese gender-specific games. Items revealing gender differences in a Chinese sample were identified and used to construct a Child Play Behavior and Activity Questionnaire (CPBAQ). Four new scales were generated through factor analysis: a Gender Scale, a Girl Typicality Scale, a Boy Typicality Scale, and a Cross-Gender Scale (CGS). These scales had satisfactory internal reliabilities and large effect sizes for gender. The CPBAQ is believed to be a promising instrument for measuring children's gender-related behavior in China.

  2. A review of chemosensation and related behavior in aquatic insects.

    Science.gov (United States)

    Crespo, José G

    2011-01-01

    Insects that are secondarily adapted to aquatic environments are able to sense odors from a diverse array of sources. The antenna of these insects, as in all insects, is the main chemosensory structure and its input to the brain allows for integration of sensory information that ultimately ends in behavioral responses. Only a fraction of the aquatic insect orders have been studied with respect to their sensory biology and most of the work has centered either on the description of the different types of sensilla, or on the behavior of the insect as a whole. In this paper, the literature is exhaustively reviewed and ways in which antennal morphology, brain structure, and associated behavior can advance better understanding of the neurobiology involved in processing of chemosensory information are discussed. Moreover, the importance of studying such group of insects is stated, and at the same time it is shown that many interesting questions regarding olfactory processing can be addressed by looking into the changes that aquatic insects undergo when leaving their aquatic environment.

  3. Changing energy-related behavior: An Intervention Mapping approach

    International Nuclear Information System (INIS)

    Kok, Gerjo; Lo, Siu Hing; Peters, Gjalt-Jorn Y.; Ruiter, Robert A.C.

    2011-01-01

    This paper's objective is to apply Intervention Mapping, a planning process for the systematic development of theory- and evidence-based health promotion interventions, to the development of interventions to promote energy conservation behavior. Intervention Mapping (IM) consists of six steps: needs assessment, program objectives, methods and applications, program development, planning for program implementation, and planning for program evaluation. Examples from the energy conservation field are provided to illustrate the activities associated with these steps. It is concluded that applying IM in the energy conservation field may help the development of effective behavior change interventions, and thus develop a domain specific knowledge-base for effective intervention design. - Highlights: → Intervention Mapping (IM) is a planning process for developing evidence-based interventions.→ IM takes a problem-driven rather than theory-driven approach. → IM can be applied to the promotion of energy-conservation in a multilevel approach. → IM helps identifying determinants of behaviors and environmental conditions. → IM helps selecting appropriate theory-based methods and practical applications.

  4. Changing energy-related behavior: An Intervention Mapping approach

    Energy Technology Data Exchange (ETDEWEB)

    Kok, Gerjo, E-mail: g.kok@maastrichtuniversity.nl [Department of Work and Social Psychology, Maastricht University, P.O. Box 616, 6200 MD Maastricht (Netherlands); Lo, Siu Hing, E-mail: siu-hing.lo@maastrichtuniversity.nl [Department of Work and Social Psychology, Maastricht University, P.O. Box 616, 6200 MD Maastricht (Netherlands); Peters, Gjalt-Jorn Y., E-mail: gj.peters@maastrichtuniversity.nl [Department of Work and Social Psychology, Maastricht University, P.O. Box 616, 6200 MD Maastricht (Netherlands); Ruiter, Robert A.C., E-mail: r.ruiter@maastrichtuniversity.nl [Department of Work and Social Psychology, Maastricht University, P.O. Box 616, 6200 MD Maastricht (Netherlands)

    2011-09-15

    This paper's objective is to apply Intervention Mapping, a planning process for the systematic development of theory- and evidence-based health promotion interventions, to the development of interventions to promote energy conservation behavior. Intervention Mapping (IM) consists of six steps: needs assessment, program objectives, methods and applications, program development, planning for program implementation, and planning for program evaluation. Examples from the energy conservation field are provided to illustrate the activities associated with these steps. It is concluded that applying IM in the energy conservation field may help the development of effective behavior change interventions, and thus develop a domain specific knowledge-base for effective intervention design. - Highlights: > Intervention Mapping (IM) is a planning process for developing evidence-based interventions.> IM takes a problem-driven rather than theory-driven approach. > IM can be applied to the promotion of energy-conservation in a multilevel approach. > IM helps identifying determinants of behaviors and environmental conditions. > IM helps selecting appropriate theory-based methods and practical applications.

  5. Prediction of the relative toxicity of environmental toxins as a function of behavioral and non-behavioral endpoints

    International Nuclear Information System (INIS)

    Young, R.W.

    1979-01-01

    This study was conducted in order to examine the differential effects of behavioral and non-behavioral endpoints on the prediction of the relative toxicity of an environmental toxin. The effects of ionizing radiation were taken as the model for this evaluation. Forty rhesus monkeys were irradiated in groups of four at five different dose levels of high energy neuton and Bremsstrahlung radiations. Measures of behavioral performance, emesis and mortality were taken for each subject in order to test the hypotheses that behavioral indices would be more sensitive to gamma radiation than would physiological indices and that the physiological indices would be more sensitive to neutron radiations than would behavioral indices. The results supported these hypotheses

  6. Discussing dementia-related behaviors during medical visits for people with Alzheimer's disease.

    Science.gov (United States)

    Hunsaker, Amanda E; Schmidt, Karen; Lingler, Jennifer H

    2010-05-01

    Research suggests that caregivers appreciate support from primary care physicians (PCPs) regarding dementia care; however, there remains a need for studies examining the role that PCPs play in behavior management. The purpose of this study was to quantitatively characterize the discussion on dementia-related behaviors (DRBs) during PCP visits and compare findings to an independently administered assessment of DRBs exhibited within a period of 4 weeks prior to the PCP visit. Twenty-five PCP visits of persons with dementia, in which caregivers coattended the visit, were audio-recorded and analyzed for occurrence of DRB discussion. Disruptive behaviors were reported by 80% of caregivers via independent assessment, yet discussed in 23% of medical visits. Dementia-related behavior discussion occurred in visits where caregivers independently reported significantly higher behavior frequency and behavior-related burden. Implications of findings for ways PCPs can assist the caregiver in behavior management are discussed.

  7. Discussing Dementia-Related Behaviors During Medical Visits for People With Alzheimer’s Disease

    Science.gov (United States)

    Hunsaker, Amanda E.; Schmidt, Karen; Lingler, Jennifer H.

    2011-01-01

    Research suggests that caregivers appreciate support from primary care physicians (PCPs) regarding dementia care; however, there remains a need for studies examining the role that PCPs play in behavior management. The purpose of this study was to quantitatively characterize the discussion on dementia-related behaviors (DRBs) during PCP visits and compare findings to an independently administered assessment of DRBs exhibited within a period of 4 weeks prior to the PCP visit. Twenty-five PCP visits of persons with dementia, in which caregivers coattended the visit, were audio-recorded and analyzed for occurrence of DRB discussion. Disruptive behaviors were reported by 80% of caregivers via independent assessment, yet discussed in 23% of medical visits. Dementia-related behavior discussion occurred in visits where caregivers independently reported significantly higher behavior frequency and behavior-related burden. Implications of findings for ways PCPs can assist the caregiver in behavior management are discussed. PMID:20147601

  8. Sleep-Related Behaviors and Beliefs Associated With Race/Ethnicity in Women

    OpenAIRE

    Grandner, Michael A.; Patel, Nirav P.; Jean-Louis, Girardin; Jackson, Nicholas; Gehrman, Philip R.; Perlis, Michael L.; Gooneratne, Nalaka S.

    2013-01-01

    Explore how social factors influence sleep, especially sleep-related beliefs and behaviors. Sleep complaints, sleep hygiene behaviors, and beliefs about sleep were studied in 65 black/African American and white/European American women. Differences were found for snoring and discrepancy between sleep duration and need. Sleep behaviors differed across groups for napping, methods for coping with sleep difficulties, and nonsleep behaviors in bed. Beliefs also distinguished groups, with difference...

  9. Oral health related knowledge and health behavior of parents and school children

    OpenAIRE

    Lalić Maja; Aleksić Ema; Gajić Mihajlo; Malešević Đoka

    2013-01-01

    Introduction. The family provides the background for developing behaviors, attitudes and knowledge related to oral health of children. The aim of this study was to compare oral health behavior of parents and their children and to asses the impact of parental behavior on children’s oral health. Material and Methods. This cross-sectional study included 99 parent - child pairs (12 to 15 years old). Data on oral health behavior, knowledge and attitudes regarding oral hygiene, fluorides and ...

  10. Effects of Cognitive Versus Cognitive-Behavioral Divorce-Parenting Programs on Parental Conflict, Intimate Violence, Parental Communication, Divorce-Related Parental Behaviors and Children's Behavioral Problems

    National Research Council Canada - National Science Library

    Whitworth, James

    2000-01-01

    .... The two-group pretest- posttest design with a three-month follow-up measured parents knowledge of divorce-related parenting behaviors, reports of intimate violence, destructive conflict tactics...

  11. Relations of behavioral autonomy to health outcomes among emerging adults with and without type 1 diabetes.

    Science.gov (United States)

    Helgeson, Vicki S; Reynolds, Kerry A; Becker, Dorothy; Escobar, Oscar; Siminerio, Linda

    2014-01-01

    To examine the relation of behavioral autonomy to psychological, behavioral, and physical health among emerging adults with and without type 1 diabetes. High school seniors with (n = 118) and without type 1 diabetes (n = 122) completed online questionnaires for three consecutive years. Behavioral autonomy, psychological health, risk behaviors, and diabetes outcomes were assessed. Regression analyses were conducted to predict Time 2 and 3 outcomes, controlling for Time 1 outcomes. There were no group differences in behavioral autonomy. Behavioral autonomy predicted better psychological health but only for emerging adults without diabetes. Behavioral autonomy was related to increased risk behavior for both groups. Behavioral autonomy was unrelated to self-care but predicted better glycemic control for females. Behavioral autonomy may be beneficial for psychological health, but is related to increased risk behavior. The implications of behavioral autonomy for emerging adults with type 1 diabetes require careful consideration. © The Author 2014. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  12. Nurses' self-care behaviors related to weight and stress.

    Science.gov (United States)

    Nahm, Eun-Shim; Warren, Joan; Zhu, Shijun; An, Minjeong; Brown, Jeanine

    2012-01-01

    Considerable research on preventive health care behaviors has been conducted in different segments of the population. Although nurses are the largest group of direct health care providers (3 million), little is known about their preventive health care behaviors. As the average age of nurses working in the United States (US) increases (mean age 47 years), maintaining their health to ensure they can continue to provide optimal health care to others becomes a greater priority. This descriptive online study examined registered nurses' dietary and exercise practices, weight status, stress levels, and preferred preventive health strategies using a sample of nurses recruited from a community-based, urban teaching hospital (n = 183; mean age 47 ± 11.3 years). The majority of participants (72.2%, n = 122) reported a lack of exercise, and more than half (53.8%, n = 91) had an irregular meal pattern. The average body mass index (BMI) was 28.3 ± 6.8, and 59.2% (n = 100) were either overweight (n = 47) or obese (n = 53). BMI had a significant inverse relationship with having a regular meal schedule and the amount of time spent exercising. Participants who reported greater stress had more irregular meal schedules. The most frequently used stress-release method was eating (n = 32), followed by exercise (n = 31). Nurses are fully aware of measures that should be taken for healthy living. Their knowledge, however, has not been well translated into their own self-care. As nursing shortages loom, maintaining the health of the aging nursing workforce is essential to retention. Further research is needed to identify factors that may motivate nurses to better care for themselves and measures that can be implemented by employers to initiate and sustain these preventive health care behaviors. Copyright © 2012 Elsevier Inc. All rights reserved.

  13. Electrochemical Label-Free Aptasensor for Specific Analysis of Dopamine in Serum in the Presence of Structurally Related Neurotransmitters

    DEFF Research Database (Denmark)

    Álvarez-Martos, Isabel; Ferapontova, Elena

    2016-01-01

    Cellular and brain metabolism of dopamine can be correlated with a number of neurodegenerative disorders, and as such, in vivo analysis of dopamine in the presence of structurally related neurotransmitters (NT) represents a holy grail of neuroscience. Interference from those NTs generally does...

  14. Longitudinal relations between adolescent and parental behaviors, parental knowledge, and internalizing behaviors among urban adolescents.

    Science.gov (United States)

    Garthe, Rachel C; Sullivan, Terri; Kliewer, Wendy

    2015-04-01

    High prevalence rates of depression and anxiety among adolescents underscore the importance of identifying parental and adolescent behaviors that may lessen the risk for these outcomes. Previous research has shown that parental acceptance, parental knowledge, and child disclosure are negatively associated with internalizing behaviors. It is also important to explore the impact of internalizing behaviors on these parental and child constructs. The current study examined longitudinal relationships between parental acceptance, parental knowledge, child disclosure, and internalizing symptoms across a one-year time period. Participants were 358 adolescents (54 % female) and their primary caregivers, who were primarily African American (92 %). Parents and adolescents provided data through face-to-face interviews. Results showed that parental knowledge and parental acceptance predicted child disclosure, and child disclosure predicted parental knowledge one year later. Higher levels of parental acceptance predicted lower levels of adolescent-reported depressive symptoms, while higher levels of parental report of adolescents' internalizing symptoms predicted lower levels of parental knowledge. No differences in the strength of these relationships were found across grade or gender. These findings highlight the role of the adolescent's perceived acceptance by parents in promoting children's disclosure, and the benefits of parental acceptance in decreasing depressive symptoms over time. Overall, these results show the impact that both adolescent and parental behaviors and internalizing behaviors have on each other across time.

  15. The Multifaceted Impact of Peer Relations on Aggressive-Disruptive Behavior in Early Elementary School

    OpenAIRE

    Powers, Christopher J.; Bierman, Karen L.

    2012-01-01

    Following a large, diverse sample of 4096 children in 27 schools, this study evaluated the impact of three aspects of peer relations, measured concurrently, on subsequent child aggressive-disruptive behavior during early elementary school – peer-dislike, reciprocated friends' aggressiveness, and classroom levels of aggressive-disruptive behavior. Teachers rated child aggressive-disruptive behavior in first and third grade, and peer relations were assessed during second grade. Results indicate...

  16. Health-Related Behaviors and Academic Achievement Among High School Students - United States, 2015.

    Science.gov (United States)

    Rasberry, Catherine N; Tiu, Georgianne F; Kann, Laura; McManus, Tim; Michael, Shannon L; Merlo, Caitlin L; Lee, Sarah M; Bohm, Michele K; Annor, Francis; Ethier, Kathleen A

    2017-09-08

    Studies have shown links between educational outcomes such as letter grades, test scores, or other measures of academic achievement, and health-related behaviors (1-4). However, as reported in a 2013 systematic review, many of these studies have used samples that are not nationally representative, and quite a few studies are now at least 2 decades old (1). To update the relevant data, CDC analyzed results from the 2015 national Youth Risk Behavior Survey (YRBS), a biennial, cross-sectional, school-based survey measuring health-related behaviors among U.S. students in grades 9-12. Analyses assessed relationships between academic achievement (i.e., self-reported letter grades in school) and 30 health-related behaviors (categorized as dietary behaviors, physical activity, sedentary behaviors, substance use, sexual risk behaviors, violence-related behaviors, and suicide-related behaviors) that contribute to leading causes of morbidity and mortality among adolescents in the United States (5). Logistic regression models controlling for sex, race/ethnicity, and grade in school found that students who earned mostly A's, mostly B's, or mostly C's had statistically significantly higher prevalence estimates for most protective health-related behaviors and significantly lower prevalence estimates for most health-related risk behaviors than did students with mostly D's/F's. These findings highlight the link between health-related behaviors and education outcomes, suggesting that education and public health professionals can find their respective education and health improvement goals to be mutually beneficial. Education and public health professionals might benefit from collaborating to achieve both improved education and health outcomes for youths.

  17. Interparental Conflict Styles and Parenting Behaviors: Associations with Overt and Relational Aggression among Chinese Children

    Science.gov (United States)

    Li, Yan; Putallaz, Martha; Su, Yanjie

    2011-01-01

    This study examined how interparental conflict styles related to Chinese children's overt and relational aggression directly and indirectly through parenting behaviors. Mothers (n = 670) and fathers (n = 570) reported their overt and covert interparental conflict styles and different parenting behaviors. Children's (n = 671) aggression was…

  18. The ENDORSE study: Research into environmental determinants of obesity related behaviors in Rotterdam schoolchildren

    NARCIS (Netherlands)

    K.A. van der Horst-Nachtegaal (Klazine); A. Oenema (Anke); P.M. van de Looij-Jansen (Petra); J. Brug (Hans)

    2008-01-01

    textabstractBackground: Children and adolescents are important target groups for prevention of overweight and obesity as overweight is often developed early in life and tracks into adulthood. Research into behaviors related to overweight (energy balance-related behaviors) and the personal

  19. Understanding work-related social media use: An extension of theory of planned behavior.

    NARCIS (Netherlands)

    van Zoonen, W.; Verhoeven, J.W.M.; Elving, W.J.L.

    2014-01-01

    This study examines the motives of employees to engage in work related social media use - i.e. the use of personal social media accounts to communicate about work-related issues. The theory of planned behavior (TPB) was used to explain this behavior. Because social media can enable users to express

  20. Does a Positive Bias Relate to Social Behavior in Children with ADHD?

    Science.gov (United States)

    Linnea, Kate; Hoza, Betsy; Tomb, Meghan; Kaiser, Nina

    2012-01-01

    This study examines whether positively biased self-perceptions relate to social behaviors in children with attention-deficit/hyperactivity disorder (ADHD) as compared to control children. The social behaviors of children with ADHD (n = 87) were examined relative to control children (CTL; n = 38) during a laboratory-based dyadic social interaction…

  1. A meta-analytic investigation of the relation between interpersonal attraction and enacted behavior.

    Science.gov (United States)

    Montoya, R Matthew; Kershaw, Christine; Prosser, Julie L

    2018-05-07

    We present a meta-analysis that investigated the relation between self-reported interpersonal attraction and enacted behavior. Our synthesis focused on (a) identifying the behaviors related to attraction; (b) evaluating the efficacy of models of the relation between attraction and behavior; (c) testing the impact of several moderators, including evaluative threat salience, cognitive appraisal salience, and the sex composition of the social interaction; and (d) investigating the degree of agreement between the meta-analytic findings and an ethnographic analysis. Using a multilevel modeling approach, an analysis of 309 effect sizes (N = 5,422) revealed a significant association (z = .20) between self-reported attraction and enacted behavior. Key findings include: (a) that the specific behaviors associated with attraction (e.g., eye contact, smiling, laughter, mimicry) are those behaviors research has linked to the development of trust/rapport; (b) direct behaviors (e.g., physical proximity, talking to), compared with indirect behaviors (e.g., eye contact, smiling, mimicry), were more strongly related to self-reported attraction; and (c) evaluative threat salience (e.g., fear of rejection) reduced the magnitude of the relation between direct behavior and affective attraction. Moreover, an ethnographic analysis revealed consistency between the behaviors identified by the meta-analysis and those behaviors identified by ethnographers as predictive of attraction. We discuss the implications of our findings for models of the relation between attraction and behavior, for the behavioral expressions of emotions, and for how attraction is measured and conceptualized. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  2. An integrated scheme for the simultaneous determination of biogenic amines, precursor amino acids, and related metabolites by liquid chromatography with electrochemical detection.

    Science.gov (United States)

    Oka, K; Kojima, K; Togari, A; Nagatsu, T; Kiss, B

    1984-06-08

    A new method using high-performance liquid chromatography with electrochemical detection (HPLC-ED) for the simultaneous determination of monoamines, their precursor amino acids, and related major metabolites in small samples of brain tissue weighing from 0.5 to 50 mg is described. The method is based on the preliminary isolation of monoamines (dopamine, norepinephrine, epinephrine, and serotonin), their precursor amino acids (tyrosine, 3,4-dihydroxyphenylalanine, tryptophan and 5-hydroxytryptophan), and their major metabolites (3-methoxytyramine, normetanephrine, 3,4-dihydroxyphenylacetic acid, homovanillic acid, vanillylmandelic acid, 3-methoxy-4-hydroxyphenylethyleneglycol, and 5-hydroxyindoleacetic acid) by chromatography on small columns of Amberlite CG-50 and Dowex 50W, and by ethyl acetate extraction. All the compounds in the four isolated fractions were measured by HPLC-ED on a reversed-phase column under four different conditions. The sensitivity was from 0.1 to 40 pmol, depending on the substances analysed. This newly established method was applied to the study of the effects of an aromatic L-amino acid decarboxylase inhibitor (NSD-1015) and a monoamine oxidase inhibitor (pargyline) on the levels of monoamines, their precursor amino acids and their major metabolites in brain regions of mice.

  3. Electrochemical studies of the corrosion behavior of a low-carbon steel in aqueous chloride solutions simulating accident conditions of radioactive waste disposal

    International Nuclear Information System (INIS)

    Farvaque-Bera, A.M.; Leistikow, S.

    1991-01-01

    The fine-grained structural steel DIN W.Nr. 1.0566 was exposed to various sulfate and chloride-containing aqueous solutions, the latter ones simulating the potential accidental environment of water intrusion into a salt mine. By electrochemical measurements in salt brines, the following results were achieved: (1) The corrosion rate is highly dependent on salt brine composition, pH and temperature. (2) Active metal dissolution led to formation of shallow pits as surface corrosion phenomenon. Thus, the application of electrochemical techniques - under non-polarized as well as under potentiodynamic conditions - proved to be suitable for fast qualitative testing of the influence of various environmental parameters on steel corrosion. (orig.)

  4. Electrochemical sensors: a powerful tool in analytical chemistry

    Directory of Open Access Journals (Sweden)

    Stradiotto Nelson R.

    2003-01-01

    Full Text Available Potentiometric, amperometric and conductometric electrochemical sensors have found a number of interesting applications in the areas of environmental, industrial, and clinical analyses. This review presents a general overview of the three main types of electrochemical sensors, describing fundamental aspects, developments and their contribution to the area of analytical chemistry, relating relevant aspects of the development of electrochemical sensors in Brazil.

  5. Using the internet: skill related problems in users’ online behavior

    NARCIS (Netherlands)

    van Deursen, Alexander Johannes Aloysius Maria; van Dijk, Johannes A.G.M.

    2009-01-01

    This study extends the conventional and superficial notion of measuring digital skills by proposing definitions for operational, formal, information and strategic skills. The main purpose was to identify individual skill related problems that users experience when navigating the Internet. In

  6. Children with Sickle-Cell Anemia: Parental Relations, Parent-Child Relations, and Child Behavior.

    Science.gov (United States)

    Evans, Robert C.; And Others

    1988-01-01

    Investigated the influence of a child with sickle-cell anemia on parental affiliation, parent-child relationships, and parents' perception of their child's behavior. In the sickle-cell group, parents' interpersonal relationship suffered; parent-child relationship and child behavior correlated significantly; and single-parent families estimated…

  7. Electrochemical energy generation

    International Nuclear Information System (INIS)

    Kreysa, G.; Juettner, K.

    1993-01-01

    The proceedings encompass 40 conference papers belonging to the following subject areas: Baseline and review papers; electrochemical fuel cells; batteries: Primary and secondary cells; electrochemical, regenerative systems for energy conversion; electrochemical hydrogen generation; electrochemistry for nuclear power plant; electrochemistry for spent nuclear fuel reprocessing; energy efficiency in electrochemical processes. There is an annex listing the authors and titles of the poster session, and compacts of the posters can be obtained from the office of the Gesellschaft Deutscher Chemiker, Abteilung Tagungen. (MM) [de

  8. Investigation of Corrosion and Cathodic Protection in Reinforced Concrete. I : Application of Electrochemical Techniques

    NARCIS (Netherlands)

    Koleva, D.A.; De Wit, J.H.W.; Van Breugel, K.; Lodhi, Z.F.; Van Westing, E.

    2007-01-01

    The electrochemical behavior of steel reinforcement in conditions of corrosion and cathodic protection was studied, using electrochemical impedance spectroscopy (EIS) and compared to reference (noncorroding) conditions. Polarization resistance (PR) method and potentiodynamic polarization (PDP) were

  9. Influence of enzymatic reactions on the electrochemical behavior of EN X2CrNiMo17-11-2 (AISI 316L) stainless steel in bio-corrosion: role of interfacial processes on the modification of the passive layer; Influence des reactions enzymatiques sur le comportement electrochimique de l'acier inoxydable ENX2CrNiMo17-11-2 (AISI 316L) en biocorrosion: role des processus interfaciaux sur la modification du film passif

    Energy Technology Data Exchange (ETDEWEB)

    Landoulsi, J

    2008-01-15

    The outstanding corrosion behavior of stainless steels (SS) results from the presence of thin oxide layer (some nanometers). In non sterile aqueous media, stainless steels may exhibit a non stable behavior resulting from interactions between microbial species and passive film. In fact, microorganisms can be deeply involved in the corrosion processes usually reported as Microbial Influenced Corrosion (MIC). They can induce the initiation or the acceleration of this phenomenon and they do so when organized in bio-films. From the electrochemical point of view, stainless steels showed an increase of the free corrosion potential (Ecorr) attributed to the bio-film settlement. The Eco' ennoblement was broadly reported in seawater and seems to be confirmed in fresh water according to recent findings. A considerable progress in the comprehension of MIC processes was related to the role of extracellular species, essentially enzymes. Many enzymatic reactions occurring in bio-films consist on using oxygen as electron acceptor to generate hydrogen peroxide and related species. The aim of this work is to understand the mechanisms involved in the electrochemical behavior of stainless steel according to an enzymatic approach in medium simulating fresh water. To this end, glucose oxidase was chosen to globalize aerobic activities of bio-films. Electrochemical measurements in situ and surface analysis allow the comprehension of the role and the nature of interfacial processes. Surface characterization was performed with the help of a new quantitative utilization of XPS analysis and AFM. Results show a significant evolution in term of morphology (surface organization), (ii) chemical composition (passive layer, adsorbed organic species) and (iii) chemical reaction (oxidation, dissolution, effect of enzyme). Finally, a new enzymatic system is proposed to mimic specific physicochemical conditions at the SS / bio-film interface, in particular enzymatic generation of oxidant species

  10. Tunable nanogap devices for ultra-sensitive electrochemical impedance biosensing

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yong [Department of Chemistry, Wannan Medical College, Wuhu 241002 (China); Guo, Zheng [Nanomaterials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Song, Jing-Jing; Huang, Qin-An; Zhu, Si-Wei [Department of Chemistry, Wannan Medical College, Wuhu 241002 (China); Huang, Xing-Jiu [Nanomaterials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Wei, Yan, E-mail: yanwei_wnmc@hotmail.com [Department of Chemistry, Wannan Medical College, Wuhu 241002 (China)

    2016-01-28

    A wealth of research has been available discussing nanogap devices for detecting very small quantities of biomolecules by observing their electrical behavior generally performed in dry conditions. We report that a gold nanogapped electrode with tunable gap length for ultra-sensitive detection of streptavidin based on electrochemical impedance technique. The gold nanogap is fabricated using simple monolayer film deposition and in-situ growth of gold nanoparticles in a traditional interdigitated array (IDA) microelectrode. The electrochemical impedance biosensor with a 25-nm nanogap is found to be ultra-sensitive to the specific binding of streptavidin to biotin. The binding of the streptavidin hinder the electron transfer between two electrodes, resulting in a large increase in electron-transfer resistance (R{sub et}) for operating the impedance. A linear relation between the relative R{sub et} and the logarithmic value of streptavidin concentration is observed in the concentration range from 1 pM (picomolar) to 100 nM (nanomolar). The lowest detectable concentration actually measured reaches 1 pM. We believe that such an electrochemical impedance nanogap biosensor provides a useful approach towards biomolecular detection that could be extended to a number of other systems. - Highlights: • A tunable gold nanogap device was used as to electrochemical impedance biosensor. • Linear range from 1 pM to 100 nM with LOD of 1 pM for streptavidin detection was obtained. • The nanogap devices exhibit a satisfactory precision, stability, and reproducibility. • The combination of electrochemical impedance technique and nanogap devices was achieved.

  11. Electrochemical surface-enhanced Raman scattering measurement on ligand capped PbS quantum dots at gap of Au nanodimer

    Science.gov (United States)

    Li, Xiaowei; Minamimoto, Hiro; Murakoshi, Kei

    2018-05-01

    The vibrational characteristics of ligand-capped lead sulfide (PbS) quantum dots (QDs) were clarified via electrochemical surface-enhanced Raman spectroscopy (EC-SERS) using a hybridized system of gold (Au) nanodimers and PbS QDs under electrochemical potential control. Enhanced electromagnetic field caused by the coupling of QDs with plasmonic Au nanodimers allowed the characteristic behavior of the ligand oleic acid (OA) on the PbS QD surface to be detected under electrochemical potential control. Binding modes between the QDs and OA molecules were characterized using synchronous two-dimensional correlation spectra at distinct electrochemical potentials, confirming that the bidentate bridging mode was probably the most stable mode even under relatively negative potential polarization. Changes in binding modes and molecular orientations resulted in fluctuations in EC-SERS spectra. The present observations strongly recommend the validity of the QD-plasmonic nanostructure coupled system for sensitive molecular detection via EC-SERS.

  12. Relation between boundary slip mechanisms and waterlike fluid behavior

    Science.gov (United States)

    Ternes, Patricia; Salcedo, Evy; Barbosa, Marcia C.

    2018-03-01

    The slip of a fluid layer in contact with a solid confining surface is investigated for different temperatures and densities using molecular dynamic simulations. We show that for an anomalous waterlike fluid the slip goes as follows: for low levels of shear, defect slip appears and is related to the particle exchange between the fluid layers; at high levels of shear, global slip occurs and is related to the homogeneous distribution of the fluid in the confining surfaces. The oscillations in the transition velocity from defect to global slip are shown to be associated with changes in the layering distribution in the anomalous fluid.

  13. THE RELATIONS WITH DEMOGRAPHIC FACTORS AND SUBDIMENSIONS OF ORGANIZATIONAL CITIZENSHIP BEHAVIORS: A STUDY IN BANKING SECTORS

    Directory of Open Access Journals (Sweden)

    KUBİLAY ÖZYER

    2013-06-01

    Full Text Available This study has been made to make clear what are the effects of demographic characteristics on workers’ organizational citizenship behaviors in service business. In this study organizational citizenship behavior was analysed with its subdimenisonals. There are 5 subdimensions as they are, alturism, conscientiousness, courtesy, civic virtue and sportsmanship. To the results of analyses, there are relations between gender, marital status, kids, hierarchical situation in organization, working organization and total organizational citizenship behavior. And also there are relations between these demographic variables and subdimensionals of organizational citizenship behaviors.

  14. Sexual orientation disparities in cancer-related risk behaviors of tobacco, alcohol, sexual behaviors, and diet and physical activity: pooled Youth Risk Behavior Surveys.

    Science.gov (United States)

    Rosario, Margaret; Corliss, Heather L; Everett, Bethany G; Reisner, Sari L; Austin, S Bryn; Buchting, Francisco O; Birkett, Michelle

    2014-02-01

    We examined sexual orientation disparities in cancer-related risk behaviors among adolescents. We pooled data from the 2005 and 2007 Youth Risk Behavior Surveys. We classified youths with any same-sex orientation as sexual minority and the remainder as heterosexual. We compared the groups on risk behaviors and stratified by gender, age ( 14 years), and race/ethnicity. Sexual minorities (7.6% of the sample) reported more risk behaviors than heterosexuals for all 12 behaviors (mean = 5.3 vs 3.8; P sexual orientation disparities in analyses by gender, followed by age, and then race/ethnicity; they persisted in analyses by gender, age, and race/ethnicity, although findings were nuanced. Data on cancer risk, morbidity, and mortality by sexual orientation are needed to track the potential but unknown burden of cancer among sexual minorities.

  15. Superhydrophobic surfaces by electrochemical processes.

    Science.gov (United States)

    Darmanin, Thierry; Taffin de Givenchy, Elisabeth; Amigoni, Sonia; Guittard, Frederic

    2013-03-13

    This review is an exhaustive representation of the electrochemical processes reported in the literature to produce superhydrophobic surfaces. Due to the intensive demand in the elaboration of superhydrophobic materials using low-cost, reproducible and fast methods, the use of strategies based on electrochemical processes have exponentially grown these last five years. These strategies are separated in two parts: the oxidation processes, such as oxidation of metals in solution, the anodization of metals or the electrodeposition of conducting polymers, and the reduction processed such as the electrodeposition of metals or the galvanic deposition. One of the main advantages of the electrochemical processes is the relative easiness to produce various surface morphologies and a precise control of the structures at a micro- or a nanoscale. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. Suicide-related behaviors and anxiety in children and adolescents: a review.

    Science.gov (United States)

    Hill, Ryan M; Castellanos, Daniel; Pettit, Jeremy W

    2011-11-01

    This paper reviews empirical evidence of the association between suicide-related behaviors and anxiety among children and adolescents. It begins with a review of suicide-related behaviors and anxiety, discusses methodological issues related to measurement, and reviews empirical findings published since the last review of this topic in 1988. Evidence is summarized on four criteria necessary to establish anxiety as a causal risk factor for suicide-related behaviors among children and adolescents. There is consistent evidence for a significant association between anxiety and suicide-related behaviors (Criterion 1). Evidence that the influence of anxiety on suicide-related behaviors is not due to a third variable (Criterion 2) is mixed and hindered by methodological limitations. The literature is also unclear as to whether anxiety temporally precedes suicide-related behaviors (Criterion 3). Finally, this review found no evidence to support or refute anxiety's stability independent of and across instances of suicide-related behaviors (Criterion 4). Theoretical and clinical implications of these findings and directions for future research are discussed. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Advertising, marketing and purchase behavior for energy-related products

    Energy Technology Data Exchange (ETDEWEB)

    Tiedemann, K.; Nelson, D.

    1998-07-01

    Energy conservation programs have relied heavily on incentives and regulatory standards to reduce residential energy consumption. However, in the changing market environment characterized by competitive pressures, alternative mechanisms such as marketing and promotions may increase substantially in importance compared to the demand-side management programs which have been the focus of most research. This paper describes the role of marketing and promotions in encouraging energy efficiency at the household level in British Columbia. The paper examines three related issues: first, the purchase process for energy-related products; second, the criteria used by customers in making purchase decisions; and third, the impact and effectiveness of alternative marketing tools. A key finding is the energy-related purchases do not fall into the impulse purchase category. There are two reasons for this: first, most of these products require installation and this requires a high level of commitment on the part of the purchaser; second, many energy-related products require a significant outlay of funds and this reduces impulse buying.

  18. Heart rate during conflicts predicts post-conflict stress-related behavior in greylag geese.

    Directory of Open Access Journals (Sweden)

    Claudia A F Wascher

    Full Text Available BACKGROUND: Social stressors are known to be among the most potent stressors in group-living animals. This is not only manifested in individual physiology (heart rate, glucocorticoids, but also in how individuals behave directly after a conflict. Certain 'stress-related behaviors' such as autopreening, body shaking, scratching and vigilance have been suggested to indicate an individual's emotional state. Such behaviors may also alleviate stress, but the behavioral context and physiological basis of those behaviors is still poorly understood. METHODOLOGY/PRINCIPAL FINDINGS: We recorded beat-to-beat heart rates (HR of 22 greylag geese in response to agonistic encounters using fully implanted sensor-transmitter packages. Additionally, for 143 major events we analyzed the behavior shown by our focal animals in the first two minutes after an interaction. Our results show that the HR during encounters and characteristics of the interaction predicted the frequency and duration of behaviors shown after a conflict. CONCLUSIONS/SIGNIFICANCE: To our knowledge this is the first study to quantify the physiological and behavioral responses to single agonistic encounters and to link this to post conflict behavior. Our results demonstrate that 'stress-related behaviors' are flexibly modulated by the characteristics of the preceding aggressive interaction and reflect the individual's emotional strain, which is linked to autonomic arousal. We found no support for the stress-alleviating hypothesis, but we propose that stress-related behaviors may play a role in communication with other group members, particularly with pair-partners.

  19. Measurement and modification of the EEG and related behavior

    Science.gov (United States)

    Sterman, M. B.

    1991-01-01

    Electrophysiological changes in the sensorimotor pathways were found to accompany the effect of rhythmic EEG patterns in the sensorimotor cortex. Additionally, several striking behavioral changes were seen, including in particular an enhancement of sleep and an elevation of seizure threshold to epileptogenic agents. This raised the possibility that human seizure disorders might be influenced therapeutically by similar training. Our objective in human EEG feedback training became not only the facilitation of normal rhythmic patterns, but also the suppression of abnormal activity, thus requiring complex contingencies directed to the normalization of the sensorimotor EEG. To achieve this, a multicomponent frequency analysis was developed to extract and separate normal and abnormal elements of the EEG signal. Each of these elements was transduced to a specific component of a visual display system, and these were combined through logic circuits to present the subject with a symbolic display. Variable criteria provided for the gradual shaping of EEG elements towards the desired normal pattern. Some 50-70% of patients with poorly controlled seizure disorders experienced therapeutic benefits from this approach in our laboratory, and subsequently in many others. A more recent application of this approach to the modification of human brain function in our lab has been directed to the dichotomous problems of task overload and underload in the contemporary aviation environment. At least 70% of all aviation accidents have been attributed to the impact of these kinds of problems on crew performance. The use of EEG in this context has required many technical innovations and the application of the latest advances in EEG signal analysis. Our first goal has been the identification of relevant EEG characteristics. Additionally, we have developed a portable recording and analysis system for application in this context. Findings from laboratory and in-flight studies suggest that we

  20. Analysis of the relation between intelligence and criminal behavior

    Directory of Open Access Journals (Sweden)

    Dragan Jovanovic

    2012-12-01

    Full Text Available Introduction: One of the cognitive aspects of personality is intelligence. A large number of previous studies have shown that the intelligence within the criminal population is decreased, particularly in its verbal aspect.The aim of this study is to determine whether there is a link between intelligence and criminal behavior and how it is manifested.Methods: The research involved criminal inmates of the Correctional institutes of Republic of Srpska and Court Department of Psychiatry Clinic Sokolac who committed homicide and various non-homicide acts. Thetest group consisted of 60 inmates who have committed homicide (homicide offenders and a control group of 60 inmates who did not commit homicide (non-homicide offenders. The study was controlled, transverse or cross-sectional study.Results: Average intelligence of inmates (homicidal and non-homicidal was IQ 95.7. Intelligence of homicide inmates was IQ 97.4 and non-homicide IQ 94.09. Intelligence coeffi cients for non-homicide inmatesubgroups were as follows - subgroup consisting of robbery offenders (IQ 96.9, subgroup consisting of theft perpetrators (IQ 93.83, subgroups consisting of other criminal offenders (IQ 92.8. Verbal intellectual ability– IQw of homicide inmates was 91.22, and 91.10 IQw of non-homicide inmates. Intellectual abilities in nonverbal or manipulative part were average, but they were higher in homicide inmates group (IQm 103.65 than in the group of non-homicide inmates (IQm 97.08.Conclusion: Average intelligence of investigated inmates (homicide and non-homicide is lower than in the general population and corresponds to low average. Verbal part of intelligence is lowered while nonverbalpart is within the average range.

  1. The Associations of Eating-related Attitudinal Balance with Psychological Well-being and Eating Behaviors

    OpenAIRE

    Fuglestad, Paul T.; Bruening, Meg; Graham, Dan J.; Eisenberg, Marla E.; Neumark-Sztainer, Dianne R.

    2013-01-01

    This study used balance theory to illuminate the relations of eating-related attitudinal consistency between self and friends to psychological well-being and eating behaviors. It was hypothesized that attitudinal inconsistency, relative to consistency, would predict lower well-being and poorer eating habits. A population-based sample of 2287 young adults participating in Project EAT-III (Eating Among Teens and Young Adults) completed measures of psychological well-being, eating behaviors, and...

  2. Sex-related online behaviors, perceived peer norms and adolescents' experience with sexual behavior : Testing an integrative model

    NARCIS (Netherlands)

    Doornwaard, Suzan M.; Ter Bogt, Tom F M; Reitz, Ellen; Van Den Eijnden, Regina J J M

    2015-01-01

    Research on the role of sex-related Internet use in adolescents' sexual development has often isolated the Internet and online behaviors from other, offline influencing factors in adolescents' lives, such as processes in the peer domain. The aim of this study was to test an integrative model

  3. Sex-related online behaviors and adolescents' body and sexual self-perceptions.

    Science.gov (United States)

    Doornwaard, Suzan M; Bickham, David S; Rich, Michael; Vanwesenbeeck, Ine; van den Eijnden, Regina J J M; ter Bogt, Tom F M

    2014-12-01

    This study investigated: (1) the prevalence and development of 2 receptive (sexually explicit Internet material [SEIM] use and sexual information seeking) and 2 interactive (cybersex and general social networking site [SNS] use) online behaviors in adolescence; (2) whether development of these behaviors predict adolescents' body and sexual self-perceptions; and (3) whether parental strategies regarding adolescents' Internet use reduce engagement in sex-related online behaviors. Four-wave longitudinal data among 1132 seventh- to 10th-grade Dutch adolescents (mean age at wave 1: 13.95 years; 52.7% boys) were collected. Developmental trajectories of sex-related online behaviors were estimated by using latent growth curve modeling. Self-perception outcomes at wave 4 and parental strategies predicting online behaviors were investigated by adding regression paths to growth models. Boys occasionally and increasingly used SEIM. Patterns for girls' SEIM use and boys' and girls' sexual information seeking and cybersex were consistently low. SNS use, however, was a common, daily activity for both. Higher initial levels and/or faster increases in sex-related online behaviors generally predicted less physical self-esteem (girls' SNS use only), more body surveillance, and less satisfaction with sexual experience. Private Internet access and less parental rule setting regarding Internet use predicted greater engagement in sex-related online behaviors. Although most sex-related online behaviors are not widespread among youth, adolescents who engage in such behaviors are at increased risk for developing negative body and sexual self-perceptions. Particular attention should be paid to adolescents' SNS use because this behavior is most popular and may, through its interactive characteristics, elicit more critical self-evaluations. Prevention efforts should focus on parents' role in reducing risky sex-related online behaviors. Copyright © 2014 by the American Academy of Pediatrics.

  4. Masculinity and HIV: Dimensions of Masculine Norms that Contribute to Men's HIV-Related Sexual Behaviors.

    Science.gov (United States)

    Fleming, Paul J; DiClemente, Ralph J; Barrington, Clare

    2016-04-01

    Numerous studies have documented a relationship between masculine norms and men's HIV-related sexual behaviors, but intervening upon this relationship requires a nuanced understanding of the specific aspects of masculine norms that shape men's sexual behaviors. We integrate theories on masculinities with empirical HIV research to identify specific dimensions of masculine norms that influence men's HIV-related sexual behaviors. We identify three major dimensions of masculine norms that shape men's sexual behavior: (1) uncontrollable male sex drive, (2) capacity to perform sexually, and (3) power over others. While the existing literature does help explain the relationship between masculine norms and men's sexual behaviors several gaps remain including: a recognition of context-specific masculinities, an interrogation of the positive influences of masculinity, adoption of an intersectional approach, assessment of changes in norms and behaviors over time, and rigorous evaluations of gender-transformative approaches. Addressing these gaps in future research may optimize prevention efforts.

  5. Longitudinal relations between adolescents' self-esteem and prosocial behavior toward strangers, friends and family.

    Science.gov (United States)

    Fu, Xinyuan; Padilla-Walker, Laura M; Brown, Michael N

    2017-06-01

    The present study examined age-trends and longitudinal bidirectional relations in self-esteem and prosocial behavior toward strangers, friends, and family over a four-year time period (age 11 to 14). A total of 681 adolescents were recruited in the United States (51% girls, 28% single parent families). A longitudinal panel model was conducted and the results showed that adolescent self-esteem was associated longitudinally with subsequent prosocial behavior toward strangers, and earlier prosocial behavior toward strangers promoted subsequent self-esteem. There were no such bidirectional relations between self-esteem and prosocial behavior toward friends and family. Findings also highlight the complexity of adolescent development of selfesteem and the multidimensional nature of prosocial behavior. Discussion focuses on understanding the dynamic interplay between adolescent selfesteem and prosocial behavior. Copyright © 2017 The Foundation for Professionals in Services for Adolescents. Published by Elsevier Ltd. All rights reserved.

  6. Within-family conflict behaviors as predictors of conflict in adolescent romantic relations.

    Science.gov (United States)

    Darling, Nancy; Cohan, Catherine L; Burns, Andrew; Thompson, Louisa

    2008-12-01

    Continuity in conflict behaviors from (a) adolescents' behavior with parents and their behavior with romantic partners and (b) from parents' marriage to adolescents' romantic relationships were examined in a sample of 58 mother-father-adolescent families and the adolescents' romantic partners. The social relations model was used to analyze within-family reports of own and partner conflict behavior. Mother-father consensus about adolescents' use of physical aggression was associated with romantic partners' reports of adolescents' physical aggression. Less functional behaviors observed during observed marital conflict were associated with a range of less functional conflict behaviors in adolescents' observed interactions with romantic partners, including withdrawal, verbal aggression, negativity, ineffective problem solving, and low cohesion. Within-family conflict and methodological issues in the use of partner and self-reports of conflict behaviors are discussed.

  7. Electrochemical Oxidation of Propene with a LSF15/CGO10 Electrochemical Reactor

    DEFF Research Database (Denmark)

    Ippolito, Davide; Kammer Hansen, Kent

    2014-01-01

    A porous electrochemical reactor, made of La0.85Sr0.15FeO3 (LSF) as electrode and Ce0.9Gd0.1O1.95 (CGO) as electrolyte, was studied for the electrochemical oxidation of propene over a wide range of temperatures. Polarization was found to enhance propene oxidation rate. Ce0.9Gd0.1O1.95 was used...... as infiltration material to enhance the effect of polarization on propene oxidation rate, especially at low temperatures. The influence of infiltrated material, as a function of heat treatment, on the reactor electrochemical behavior has been evaluated by using electrochemical impedance spectroscopy...... in suppressing the competing oxygen evolution reaction and promoting the oxidation of propene under polarization, with faradaic efficiencies above 70% at 250◦C. © 2014 The Electrochemical Society....

  8. The relation of serotonin-related gene and COMT gene polymorphisms with criminal behavior in schizophrenic disorder.

    Science.gov (United States)

    Koh, Kyung Bong; Choi, Eun Hee; Lee, Young-joon; Han, Mooyoung; Choi, Sang-Sup; Kim, So Won; Lee, Min Goo

    2012-02-01

    It has been suggested that patients with schizophrenia might be involved in criminal behavior, such as homicidal and violent behavior. However, the relationship between criminal behavior and genes in patients with schizophrenia has not been clearly elucidated. The objective of this study was to examine the relation between criminal behavior and serotonin-related gene or catechol-O-methyltransferase (COMT) gene polymorphisms in patients with schizophrenia. Serotonin-related and COMT polymorphic markers were assessed by using single nucleotide polymorphism (SNP) genotyping. Ninety-nine crime-related inpatients with schizophrenia (57 homicidal and 42 nonhomicidal violent) and 133 healthy subjects were enrolled between October 2005 and May 2008. Diagnoses were made according to the Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition (DSM-IV) criteria. The genotype frequencies of tryptophan hydroxylase-1 (TPH1) A218C and COMT V158M were compared between groups. The TPH1 CC genotype had 2.7-fold higher odds of crime-related schizophrenia compared with A-carrier genotype after the analysis was controlled for sex and age (OR, 2.69; 95% CI, 1.22 - 5.91; P = .01). In addition, the TPH1 CC genotype had 3.4-fold higher odds of homicidal schizophrenia compared with A-carrier genotype after the analysis was controlled for sex and age (OR, 3.38; 95% CI, 1.40 - 8.18; P = .007). However, no significant differences were found in the frequencies of genotype of COMT polymorphism between criminal schizophrenics and healthy subjects, nor were any significant differences found between nonhomicidal schizophrenics and healthy subjects. These results indicate that the TPH1 CC recessive genotype is likely to be a genetic risk factor for criminal behavior, especially homicidal behavior in patients with schizophrenia. However, COMT gene polymorphisms were not associated with criminal behavior in schizophrenic patients. © Copyright 2012 Physicians Postgraduate Press, Inc.

  9. Environment-behavior relations, behavior therapy and the process of persuasion and attitude change.

    Science.gov (United States)

    Schauss, S L; Chase, P N; Hawkins, R P

    1997-03-01

    The phenomena described by the cognitive dissonance literature, especially to explain attitude change, have important relevance to understanding certain aspects of therapy. Contrary to popular beliefs, these phenomena can be described in behavior-analytic terms. To do so requires an analysis of learning histories that select and maintain consistency in what individuals say and do. An understanding of the environmental variables that produce consistency can then be applied to the kinds of attitude change and stability found in the cognitive dissonance literature that have therapeutic importance.

  10. Electrochemical dictionary

    CERN Document Server

    Bard, Allen J; Scholz, Fritz 0

    2014-01-01

    This comprehensive dictionary includes some 3000 common terms in electrochemistry and energy research, and related fields. Offers clear, precise definitions, references and more than 600 illustrations. The new edition adds more than 300 new and revised terms.

  11. The health-related behaviors and attitudes of student nurses

    Science.gov (United States)

    Vowell, Maribeth

    Nurses are an important component of primary medical care, and patient education is a common and important role of most nurses. Patient education and positive role modeling by nurses have the potential to influence patients' life style choices and the serious diseases that may be affected by those choices. A greater understanding of the ways nurses think about their own health could help facilitate healthier choices for them and in their patients. The purpose of this inquiry was to examine the experiences, attitudes and beliefs of student nurses related to their personal health, and to investigate those experiences, attitudes and beliefs as they relate to their education, relationships, values and career choice. The purpose was achieved through phenomenological interviews with eleven senior nursing students, nine females and two males, encouraging them to provide in as much detail as possible their attitudes and values about their personal health. The interviews were tape recorded, transcribed verbatim, and phenomenologically analyzed. A thematic structure emerged such that the nursing students experiences were represented by the four interrelated themes of caring for myself/caring for others ; I control my health/my world controls my health; I have energy/I'm tired; and feeling good/looking good. The contextual grounds for the themes that emerged during the analysis were the Body and Time. This structure was presented in terms of its relationship to health education, other research and to current theory.

  12. Electrochemical behaviors and simultaneous determination of guanine and adenine based on graphene–ionic liquid–chitosan composite film modified glassy carbon electrode

    International Nuclear Information System (INIS)

    Niu Xiuli; Yang Wu; Ren Jie; Guo Hao; Long Shijia; Chen Jiaojiao; Gao Jinzhang

    2012-01-01

    Highlights: ► This work developed a novel electrochemical biosensors for guanine and adenine detection simultaneously. ► A disposable electrode based on graphene sheets, ionic liquid and chitosan was proposed. ► The presented method was also applied to simultaneous determination of guanine and adenine in denatured DNA samples with satisfying results. ► Easy fabrication, high sensitivity, excellent reproducibility and long-term stability. - Abstract: A graphene sheets (GS), ionic liquid (IL) and chitosan (CS) modified electrode was fabricated and the modified electrode displayed excellent electrochemical catalytic activities toward guanine and adenine. The transfer electron number (n) and the charge transfer coefficient (α) were calculated with the result as n = 2, α = 0.58 for guanine, and n = 2, α = 0.51 for adenine, which indicated the electrochemical oxidation of guanine and adenine on GS/IL/CS modified electrode was a two-electron and two-proton process. The oxidation overpotentials of guanine and adenine were decreased significantly compared with those obtained at the bare glassy carbon electrode and multi-walled carbon nanotubes modified electrode. The modified electrode exhibited good analytical performance and was successfully applied for individual and simultaneous determination of guanine and adenine. Low detection limits of 0.75 μM for guanine and 0.45 μM for adenine were obtained, with the linear calibration curves over the concentration range 2.5–150 μM and 1.5–350 μM, respectively. At the same time, the proposed method was successfully applied for the determination of guanine and adenine in denatured DNA samples with satisfying results. Moreover, the GS/IL/CS modified electrode exhibited good sensitivity, long-term stability and reproducibility for the determination of guanine and adenine.

  13. Simultaneous Voltammetric Determination of Acetaminophen and Isoniazid (Hepatotoxicity-Related Drugs) Utilizing Bismuth Oxide Nanorod Modified Screen-Printed Electrochemical Sensing Platforms.

    Science.gov (United States)

    Mahmoud, Bahaa G; Khairy, Mohamed; Rashwan, Farouk A; Banks, Craig E

    2017-02-07

    To overcome the recent outbreaks of hepatotoxicity-related drugs, a new analytical tool for the continuously determination of these drugs in human fluids is required. Electrochemical-based analytical methods offer an effective, rapid, and simple tool for on-site determination of various organic and inorganic species. However, the design of a sensitive, selective, stable, and reproducible sensor is still a major challenge. In the present manuscript, a facile, one-pot hydrothermal synthesis of bismuth oxide (Bi 2 O 2.33 ) nanostructures (nanorods) was developed. These BiO nanorods were cast onto mass disposable graphite screen-printed electrodes (BiO-SPEs), allowing the ultrasensitive determination of acetaminophen (APAP) in the presence of its common interference isoniazid (INH), which are both found in drug samples. The simultaneous electroanalytical sensing using BiO-SPEs exhibited strong electrocatalytic activity toward the sensing of APAP and INH with an enhanced analytical signal (voltammetric peak) over that achievable at unmodified (bare) SPEs. The electroanalytical sensing of APAP and INH are possible with accessible linear ranges from 0.5 to 1250 μM and 5 to 1760 μM with limits of detection (3σ) of 30 nM and 1.85 μM, respectively. The stability, reproducibility, and repeatability of BiO-SPE were also investigated. The BiO-SPEs were evaluated toward the sensing of APAP and INH in human serum, urine, saliva, and tablet samples. The results presented in this paper demonstrate that BiO-SPEs sensing platforms provide a potential candidate for the accurate determination of APAP and INH within human fluids and pharmaceutical formulations.

  14. Electrochemical study and recovery of Pb using 1:2 choline chloride/urea deep eutectic solvent: A variety of Pb species PbSO4, PbO2, and PbO exhibits the analogous thermodynamic behavior

    International Nuclear Information System (INIS)

    Liao, Yu-Shun; Chen, Po-Yu; Sun, I-Wen

    2016-01-01

    Water-insoluble PbSO 4 , PbO 2 , and PbO are fairly soluble in choline chloride/urea deep eutectic solvent (ChCl/urea DES) in 1:2 molar ratio. Very interestingly, solution prepared from PbO 2 exhibits the almost identical electrochemical behavior as those from PbSO 4 and PbO, indicating that Pb(II) is formed in the DES regardless of what Pb compound is introduced. The electrochemical reduction of the Pb(II) species is determined as an irreversible process, and involves the three-dimensional (3D) instantaneous nucleation with diffusion-controlled growth. From the dependence of the diffusion coefficient on temperature, the activation energy for diffusion of PbSO 4 and PbO 2 is determined to be 33.7 and 34.1 kJ mol −1 , respectively. Electrodeposition of Pb was achieved potentiostatically and galvanostatically. The surface morphology of Pb deposits significantly depends on the applied potential and current. The coulombic efficiency of Pb electrodeposition is higher than 90%. Electrodeposition of Pb from a wet DES containing a mixture of three different Pb sources is also investigated. The XRD analysis confirmed that the electrodeposits consisted of metallic Pb.

  15. A Silsesquioxane Organically Modified with 4-Amino-5-(4-pyridyl-4H-1,2,4-triazole-3-thiol: Thermal Behavior and Its Electrochemical Detection of Sulfhydryl Compounds

    Directory of Open Access Journals (Sweden)

    D. R. Do Carmo

    2014-01-01

    Full Text Available The octakis(3-chloropropylsilsesquioxane (SS was organofunctionalized with 4-amino-5-4(pyridyl-4H-1,2,4-triazole-3-thiol. The product formed (SA was undergo another reactions in two steps, first with copper and so hexacyanoferrate (III to form CuHSA. The organofunctionalized silsesquioxane was characterized by the following techniques: scanning electron microscopy (SEM, Fourier transform infrared (FTIR, nuclear magnetic resonance (NMR in solid state, and thermogravimetric analysis in air and nitrogen atmosphere. The composite CuHSA was incorporated into a graphite paste electrode and the electrochemical behavior studies were conducted with cyclic voltammetry. The cyclic voltammogram of the modified graphite paste electrode with CuHSA showed one redox couple with formal potential Eθ′=0.75 V versus Ag/AgCl(sat (KCl 1.0 mol L−1; v = 20 mV s−1 attributed to the redox process Fe(II(CN6/Fe(III(CN6 of the binuclear complex formed. The redox couple presents an electrocatalytic response of sulfhydryl compounds such as n-acetylcysteine and l-cysteine. For determination of n-acetylcysteine and l-cysteine the modified graphite paste electrode showed a linear region in the concentration range of 2 to 20 mmol L−1. The modified electrode was chemically and electrochemically stable and showed good reproducibility.

  16. In-Situ Electrochemical Corrosion Behavior of Nickel-Base 718 Alloy Under Various CO2 Partial Pressures at 150 and 205 °C in NaCl Solution

    Science.gov (United States)

    Zhang, Yubi; Zhao, Yongtao; Tang, An; Yang, Wenjie; Li, Enzuo

    2018-03-01

    The electrochemical corrosion behavior of nickel-base alloy 718 was investigated using electrochemical impedance spectroscopy and potentiodynamic polarization techniques at various partial pressures of CO2 (P_{{{CO}2 }} s) in a 25 wt% NaCl solution at 150 and 205 °C. The passive films composed of FeCO3 exhibit good corrosion resistance with a feature of Warburg impedance, Tafel plots show a complete passivation and the anodic reactions was dominated by a diffusion process at low P_{{{CO}2 }} s (1.8-9.8 MPa) at 150 °C. While numerous dented corrosion areas appeared on the sample surface for the P_{{{CO}2 }} of 11.6 MPa at 205 °C, the Tafel plot with three anodic peaks and the Nyquist diagram with an atrophied impedance arc were present. This dented corrosion attribute to the synergistic effects of stress, temperature, P_{{{CO}2 }} and Cl-, the temperature and stress could play crucial roles on the corrosion of the alloy 718.

  17. Relative Effects of Daily Feedback and Weekly Feedback on Customer Service Behavior at a Gas Station

    Science.gov (United States)

    So, Yongjoon; Lee, Kyehoon; Oah, Shezeen

    2013-01-01

    The relative effects of daily and weekly feedback on customer service behavior at a gas station were assessed using an ABC within-subjects design. Four critical service behaviors were identified and measured daily. After baseline (A), weekly feedback (B) was introduced, and daily feedback (C) was introduced in the next phase. The results indicated…

  18. Maternal Caregiving Moderates the Relation between Temperamental Fear and Social Behavior with Peers

    Science.gov (United States)

    Penela, Elizabeth C.; Henderson, Heather A.; Hane, Amie A.; Ghera, Melissa M.; Fox, Nathan A.

    2012-01-01

    Temperament works in combination with a child's environment to influence early socioemotional development. We examined whether maternal caregiving behavior at infant age 9 months moderated the relation between infant temperamental fear (9 months) and observations of children's social behavior with an unfamiliar peer at age 2 in a typically…

  19. Relations between student teachers’ basic needs fulfillment and their teaching behavior

    NARCIS (Netherlands)

    Korthagen, Fred A J|info:eu-repo/dai/nl/06936432X; Evelein, Frits G.|info:eu-repo/dai/nl/304827452

    2016-01-01

    This study examines the relation between fulfillment of the three basic psychological needs in 36 student teachers and their teaching behavior, based on Self-Determination Theory (Deci & Ryan, 2002) and the Model for Interpersonal Teacher Behavior (Wubbels, Den Brok, Van Tartwijk, & Levy, 2012).

  20. Two Sides of the Same Coin? The Relations between Prosocial and Physically Aggressive Behaviors

    Science.gov (United States)

    McGinley, Meredith; Carlo, Gustavo

    2007-01-01

    The direct and indirect relations between six types of prosocial behavior and physical aggression were examined. Data were gathered from 252 college students (M age = 21.67 years; 184 women) who completed measures of sympathy, prosocial behavior, and physical aggression. Structural equation modeling revealed that sympathy fully mediated the…