Anisotropic Material Behavior of Uni-axially Compacted Graphite Matrix for HTGR Fuel Compact Fabrication

International Nuclear Information System (INIS)

Lee, Young-Woo; Yeo, Seunghwan; Yoon, Ji-Hae; Cho, Moon Sung

2016-01-01

In developing the fuel compact fabrication technology, and fuel graphite material to meet the required material properties, it is essential to investigate the relationship among the process parameters of the matrix graphite powder preparation, the fabrication parameters of fuel element green compact and the heat treatments conditions and the material properties of fuel element. It was observed, during this development, that the pressing technique employed for the compaction fabrication prior to the two successive heat treatments (carbonization and final high temperature heat treatment) was of extreme importance in determining the material properties of the final compact product. In this work, the material behavior of the uni-axially pressed graphite matrix during the carbonization and final heat treatment are evaluated and summarized along the different directions, viz., perpendicular and parallel directions to pressing direction. In this work, the dimensional variations and variations in thermal expansion, thermal conductivity and Vickers hardness of the graphite matrix compact samples in the axial and radial directions prepared by uni-axial pressing are evaluated, and compared with those of samples prepared by cold isostatic pressing with the available data. From this work, the followings are observed. 1) Dimensional changes of matrix graphite green compacts during carbonization show that the difference in radial and axial variations shows a large anisotropic behavior in shrinkage. The radial variation is very small while the axial variation is large. During carbonization, the stresses caused by the force would be released in to the axial direction together with the phenolic resin vapor. 2) Dimensional variation of compact samples in perpendicular and parallel directions during carbonization shows a large difference in behavior when compact sample is prepared by uni-axial pressing. However, when compact sample is prepared by cold isostatic pressing, there is

Comparison of improved finite-difference WENO schemes for the implicit large eddy simulation of turbulent non-reacting and reacting high-speed shear flows

International Nuclear Information System (INIS)

Zhao, S.; Lardjane, N.; Fedioun, I.

2014-01-01

Improved WENO schemes, Z, M, and their combination MZ, originally designed to capture sharper discontinuities than the classical fifth order Jiang-Shu scheme does, are evaluated for the purpose of implicit large eddy simulation of free shear flows. 1D Fourier analysis of errors reveals the built-in filter and dissipative properties of the schemes, which are subsequently applied to the canonical Rayleigh-Taylor and Taylor-Green flows. Large eddy simulations of a transonic non-reacting and a supersonic reacting air/H2 jets are then performed at resolution 128 * 128 * 512, showing no significant difference in the flow statistics. However, the computational time varies from one scheme to the other, the Z scheme providing the smaller wall-time due to larger allowed time steps. (authors)

A study on some properties of sintered stainless steel powder compacts with sintering conditions

International Nuclear Information System (INIS)

Lee, Bang Sik; Kim, Kwan Hyu; Lee, Doh Jae; Choi, Dap Chun

1986-01-01

Sintered specimens for the mechanical and corrosion tests were prepared from 316L, 410L and 434L stainless steel powder compacts with green densities in the range of 6.2∼7.0g/cm 3 . The experimental variables studied were green density, sintering atmosphere, temperature and time, type of lubricant used and cooling rate after sintering operation. Mechanical properties of green compacts and sintered specimens were evaluated. The corrosion tests were performed by potentiodynamic anodic polarization technique. Mechanical properties were very sensitive to the sintering atmosphere; sintering in dissociated ammonia resulted in the strengthing but embrittlement of sintered 316L, 410L and 434L strainless steel powder compacts. Their corrosion resistance was also decreased. The tensile strength was increased with increases in sintering time and temperature while the decreases in the yield strength were observed. The tensile properties of green compacts were shown to closely related to the green density. Addition of 1% acrawax as a lubricant was appeared to be most effective for the improvement of green strength. (Author)

Dimensional Behavior of Matrix Graphite Compacts during Heat Treatments for HTGR Fuel Element Fabrication

International Nuclear Information System (INIS)

Lee, Young-Woo; Yeo, Seunghwan; Cho, Moon Sung

2015-01-01

The carbonization is a process step where the binder that is incorporated during the matrix graphite powder preparation step is evaporated and the residue of the binder is carbonized during the heat treatment at about 1073 K. This carbonization step is followed by the final high temperature heat treatment where the carbonized compacts are heat treated at 2073-2173 K in vacuum for a relatively short time (about 2 hrs). In order to develop a fuel compact fabrication technology, and for fuel matrix graphite to meet the required material properties, it is essential to investigate the relationship among the process parameters of the matrix graphite powder preparation, the fabrication parameters of fuel element green compact and the heat treatments conditions, which has a strong influence on the further steps and the material properties of fuel element. In this work, the dimensional changes of green compacts during the carbonization and final heat treatment are evaluated when compacts have different densities from different pressing conditions and different final heat treatment temperatures are employed, keeping other process parameters constant, such as the binder content, carbonization time, temperature and atmosphere (two hours ant 1073K and N2 atmosphere). In this work, the dimensional variations of green compacts during the carbonization and final heat treatment are evaluated when compacts have different densities from different pressing conditions and different final heat treatment temperatures are employed

Characterization by X-ray tomography of granulated alumina powder during in situ die compaction

Energy Technology Data Exchange (ETDEWEB)

Cottrino, Sandrine; Jorand, Yves, E-mail: yves.jorand@insa-lyon.fr; Maire, Eric; Adrien, Jérôme

2013-07-15

Compaction process, the aim of which being to obtain green bodies with low porosity and small size, is often used before sintering treatment. Prior to die filling, the ceramic powder is generally granulated to improve flowability. However during compaction, density heterogeneity and critical size defects may appear due to intergranule and granule-die wall frictions. In this work, the influence of granule formulation on the compact morphology has been studied. To do so, a compaction setup was installed inside an X-ray tomography equipment so that the evolution of the compact morphology could be analysed during the whole compaction process. We have demonstrated that high humidity rate and the addition of binder in the granule formulation increase density heterogeneity and generate larger defects. - Highlights: • An original compaction set up was installed inside an X-Ray tomography equipment. • The compaction process of granulated ceramic powder is imaged. • The compact green microstructure is quantified and related to the compaction stages. • The most detrimental defects of dry-pressed parts are caused by hollow granules. • Formulations without binder allow a reduction of the number of large defects.

Comparison of Mixing Calculations for Reacting and Non-Reacting Flows in a Cylindrical Duct

Science.gov (United States)

Oechsle, V. L.; Mongia, H. C.; Holdeman, J. D.

1994-01-01

A production 3-D elliptic flow code has been used to calculate non-reacting and reacting flow fields in an experimental mixing section relevant to a rich burn/quick mix/lean burn (RQL) combustion system. A number of test cases have been run to assess the effects of the variation in the number of orifices, mass flow ratio, and rich-zone equivalence ratio on the flow field and mixing rates. The calculated normalized temperature profiles for the non-reacting flow field agree qualitatively well with the normalized conserved variable isopleths for the reacting flow field indicating that non-reacting mixing experiments are appropriate for screening and ranking potential rapid mixing concepts. For a given set of jet momentum-flux ratio, mass flow ratio, and density ratio (J, MR, and DR), the reacting flow calculations show a reduced level of mixing compared to the non-reacting cases. In addition, the rich-zone equivalence ratio has noticeable effect on the mixing flow characteristics for reacting flows.

Effects of forming temperature and sintering rate to the final properties of FeCuAl powder compacts formed through uniaxial die compaction process

Science.gov (United States)

Rahman, M. M.; Ismail, M. A.; Sopyan, I.; Rahman, H. Y.

2018-01-01

This paper presents the outcomes of an experimental investigation on the effects of forming temperature and sintering schedule to the final characteristics of FeCuAl powder mass formed at different temperature and sintered at different schedule. A lab-scale uni-axial die compaction rig was designed and fabricated which enabled the compaction of powder mass at room temperature as well as elevated temperature. Iron (Fe) powder ASC 100.29 was mechanically mixed with other elemental powders, namely copper (Cu), and aluminum (Al) for 60 minutes and compacted at three different temperature, i.e., 30°C, 150°C, and 200°C by applying 425 MPa of simultaneous downward and upward axial loading to generate green compacts. The as-pressed samples were inspected visually and the defect-free green compacts were subsequently sintered in an argon gas fired furnace at 800°C for 60 min at three different heating/cooling rates, i.e., 5, 10, and 15°C/min, respectively. The sintered samples were then characterised for their physical, electrical, and mechanical properties. The microstructures of the sintered samples were also analysed. The results revealed that a forming temperature of 150°C and a sintering rate of 10°C/min could produce a product with better characteristics.

An Experiment on the Carbonization of Fuel Compact Matrix Graphite for HTGR

International Nuclear Information System (INIS)

Lee, Young Woo; Kim, Joo Hyoung; Cho, Moon Sung

2012-01-01

The fuel element for HTGR is manufactured by mixing coated fuel particles with matrix graphite powder and forming into either pebble type or cylindrical type compacts depending on their use in different HTGR cores. The coated fuel particle, the so-called TRISO particle, consists of 500-μm spherical UO 2 particles coated with the low density buffer Pyrolytic Carbon (PyC) layer, the inner and outer high density PyC layer and SiC layer sandwiched between the two inner and outer PyC layers. The coated TRISO particles are mixed with a properly prepared matrix graphite powder, pressed into a spherical shape or a cylindrical compact, and finally heat-treated at about 1800 .deg. C. These fuel elements can have different sizes and forms of compact. The basic steps for manufacturing a fuel element include preparation of graphite matrix powder, over coating the fuel particles, mixing the fuel particles with a matrix powder, carbonizing green compact, and the final high-temperature heat treatment of the carbonized fuel compact. The carbonization is a process step where the binder that is incorporated during the matrix graphite powder preparation step is evaporated and the residue of the binder is carbonized during the heat treatment at about 1073 K, In order to develop a fuel compact fabrication technology, and for fuel matrix graphite to meet the required material properties, it is of extreme importance to investigate the relationship among the process parameters of the matrix graphite powder preparation, fabrication parameters of fuel element green compact and the carbonization condition, which has a strong influence on further steps and the material properties of fuel element. In this work, the carbonization behavior of green compact samples prepared from the matrix graphite powder mixtures with different binder materials was investigated in order to elucidate the behavior of binders during the carbonization heat treatment by analyzing the change in weight, density and its

Adaptive Feature Based Control of Compact Disk Players

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Stoustrup, Jakob; Vidal, Enrique Sanchez

2005-01-01

Many have experienced the problem that their Compact Disc players have difficulties playing Compact Discs with surface faults like scratches and fingerprints. The cause of this is due to the two servo control loops used to keep the Optical Pick-up Unit focused and radially on the information track...... of the Compact Disc. The problem is to design servo controllers which are well suited for handling surface faults which disturb the position measurement and still react sufficiently against normal disturbances like mechanical shocks. In previous work of the same authors a feature based control scheme for CD......-players playing CDs with surface fault is derived and described. This feature based control scheme uses precomputed base to remove the surface fault influence from the position measurements. In this paper an adaptive version of the feature based control scheme is proposed and described. This adaptive scheme can...

On the combined effect of lubrication and compaction temperature on properties of iron-based P/M parts

International Nuclear Information System (INIS)

Babakhani, Abolfazl; Haerian, Ali; Ghambari, Mohammad

2006-01-01

Addition of lubricant in the form of admixed with powder reduces friction between die wall and powder during compaction of P/M parts. However, it has detrimental effect on mechanical properties. On the other hand, warm compaction of powders improves density and hence, the mechanical properties of these parts. Die wall lubrication can be used along with warm compaction to avoid the disadvantages of the admixed lubricant while reducing the friction, and benefiting the advantages of warm compaction. In this study, the combined effect of warm compaction and die wall lubrication with various amounts of admixed lubricant has been examined. Compacts were made of admixed powders containing from 0 to 0.6% lithium stearate with the die wall lubricated by 1.5% emulsion of lithium stearate under two different pressing pressures of 500 and 650 MPa. The temperatures used were: RT, 130, 150 and 165 deg. C. It was found out that at both compaction pressures, reduction of admixed lubricant down to 0% increased the green density and mechanical properties of the sintered parts. For samples pressed at 500 and 650 MPa the increase in green density due to elimination of admixed lubricant and using die wall lubrication was 0.33 and 0.35 g/cm 3 , respectively. It was also found out that die wall lubrication is more effective in increasing green density at higher compaction pressures. Sinter density and mechanical properties increased by increasing compaction temperature up to 150 deg. C. Both parameters were deteriorated above this temperature for admixed powders, while it kept increasing for die wall lubrication

Sintering studies on iron-carbon-copper compacts

Directory of Open Access Journals (Sweden)

Perianayagam Philomen-D-Anand Raj

2016-01-01

Full Text Available Sintered Iron-Carbon-Copper parts are among the most widely used powder metallurgy product in automobile. In this paper, studies have been carried out to find out the sintering characteristics of iron-carbon-copper compacts when sintered in nitrogen atmosphere. The effects of various processing parameters on the sintering characteristics were studied. The various processing parameters considered were compaction pressure, green density and sintering temperature. The sintering characteristics determined were sintered density, porosity, dimensional change, micro hardness and radial crush strength. The results obtained have been discussed on the basis of micro structural observations. The characteristics of SEM fractography were also used to determine the mechanism of fracture. The fracture energy is strongly dependent on density of the compact.

Worldline Green functions for multiloop diagrams

International Nuclear Information System (INIS)

Schmidt, M.G.; Heidelberg Univ.; Schubert, C.

1994-03-01

We propose a multiloop generalization of the Bern-Kosower formalism, based on Strassler's approach of evaluating worldline path integrals by worldline Green functions. Those Green functions are explicitly constructed for the basic two-loop graph, and for a loop with an arbitrary number of propagator insertions. For scalar and abelian gauge theories, the resulting integral representations allow to combine whole classes of Feynman diagrams into compact expressions. (orig.)

Incorporation of Monovalent Cations in Sulfate Green Rust

DEFF Research Database (Denmark)

Christiansen, B. C.; Dideriksen, K.; Katz, A.

2014-01-01

Green rust is a naturally occurring layered mixed-valent ferrous-ferric hydroxide, which can react with a range of redox-active compounds. Sulfate-bearing green rust is generally thought to have interlayers composed of sulfate and water. Here, we provide evidence that the interlayers also contain...... with water showed that Na+ and K+ were structurally fixed in the interlayer, whereas Rb+ and Cs+ could be removed, resulting in a decrease in the basal layer spacing. The incorporation of cations in the interlayer opens up new possibilities for the use of sulfate green rust for exchange reactions with both...

Effects of compaction pressure and particle shape on the porosity and compression mechanical properties of sintered Ti6Al4V powder compacts for hard tissue implantation.

Science.gov (United States)

Güden, Mustafa; Celik, Emrah; Hizal, Alpay; Altindiş, Mustafa; Cetiner, Sinan

2008-05-01

Sintered Ti6Al4V powder compacts potentially to be used in implant applications were prepared using commercially available spherical and angular powders (100-200 mum) within the porosity range of 34-54%. Cylindrical green powder compacts were cold compacted at various pressures and then sintered at 1200 degrees C for 2 h. The final percent porosity and mean pore sizes were determined as functions of the applied compaction pressure and powder type. The mechanical properties were investigated through compression testing. Results have shown that yield strength of the powder compacts of 40-42% porosity was comparable with that of human cortical bone. As compared with previously investigated Ti powder compacts, Ti6Al4V powder compacts showed higher strength at similar porosity range. Microscopic observations on the failed compact samples revealed that failure occurred primarily by the separation of interparticle bond regions in the planes 45 degrees to the loading axis. Copyright 2007 Wiley Periodicals, Inc.

A Green Solvent Induced DNA Package

Science.gov (United States)

Satpathi, Sagar; Sengupta, Abhigyan; Hridya, V. M.; Gavvala, Krishna; Koninti, Raj Kumar; Roy, Bibhisan; Hazra, Partha

2015-03-01

Mechanistic details of DNA compaction is essential blue print for gene regulation in living organisms. Many in vitro studies have been implemented using several compaction agents. However, these compacting agents may have some kinds of cytotoxic effects to the cells. To minimize this aspect, several research works had been performed, but people have never focused green solvent, i.e. room temperature ionic liquid as DNA compaction agent. To the best of our knowledge, this is the first ever report where we have shown that guanidinium tris(pentafluoroethyl)trifluorophosphate (Gua-IL) acts as a DNA compacting agent. The compaction ability of Gua-IL has been verified by different spectroscopic techniques, like steady state emission, circular dichroism, dynamic light scattering and UV melting. Notably, we have extensively probed this compaction by Gua-IL through field emission scanning electron microscopy (FE-SEM) and fluorescence microscopy images. We also have discussed the plausible compaction mechanism process of DNA by Gua-IL. Our results suggest that Gua-IL forms a micellar kind of self aggregation above a certain concentration (>=1 mM), which instigates this compaction process. This study divulges the specific details of DNA compaction mechanism by a new class of compaction agent, which is highly biodegradable and eco friendly in nature.

Optimization and Surface Modification of Al-6351 Alloy Using SiC-Cu Green Compact Electrode by Electro Discharge Coating Process

Science.gov (United States)

Chakraborty, Sujoy; Kar, Siddhartha; Dey, Vidyut; Ghosh, Subrata Kumar

2017-06-01

This paper introduces the surface modification of Al-6351 alloy by green compact SiC-Cu electrode using electro-discharge coating (EDC) process. A Taguchi L-16 orthogonal array is employed to investigate the process by varying tool parameters like composition and compaction load and electro-discharge machining (EDM) parameters like pulse-on time and peak current. Material deposition rate (MDR), tool wear rate (TWR) and surface roughness (SR) are measured on the coated specimens. An optimum condition is achieved by formulating overall evaluation criteria (OEC), which combines multi-objective task into a single index. The signal-to-noise (S/N) ratio, and the analysis of variance (ANOVA) is employed to investigate the effect of relevant process parameters. A confirmation test is conducted based on optimal process parameters and experimental results are provided to illustrate the effectiveness of this approach. The modified surface is characterized by optical microscope and X-ray diffraction (XRD) analysis. XRD analysis of the deposited layer confirmed the transfer of tool materials to the work surface and formation of inter-metallic phases. The micro-hardness of the resulting composite layer is also measured which is 1.5-3 times more than work material’s one and highest layer thickness (LT) of 83.644μm has been successfully achieved.

Explosive material treatment in particular the explosive compaction of powders

International Nuclear Information System (INIS)

Pruemmer, R.

1985-01-01

The constructive use of explosives in the last decades has led to new procedures in manufacturing techniques. The most important of these are explosive forming and cladding, the latter especially for the production of compound materials. The method of explosive compaction has the highest potential for further innovation. Almost theoretical densities are achievable in the green compacts as the pressure released by detonating explosives are very high. Also, the production of new conditions of materials (metastable high pressure phases) is possible. (orig.) [de

Cracking cone fracture after cold compaction of argillaceous particles

Indian Academy of Sciences (India)

In this work an experimental investigation has been focused on the `cracking cone' fracture in powder compacts. This includes studies of crack propagation and determination of operating conditions to avoid the green body fracture. The numerical modelling is implemented using a finite element method based on the Von ...

Characterisation and compaction behaviour of UO2 powder prepared from ADU and AUC

International Nuclear Information System (INIS)

Rachmawati, M.

2000-01-01

UO 2 powder prepared from ADU and AUC route process are characterised primarily in terms of compaction and sintering behaviour. Scientific understanding of the phenomena will give useful information leading to processing and product improvement. The investigation has been done by characterising the particle size/shape distribution using SEM and compacting the powder at 4 and 5.4 tons/cm 2 . The behaviour of the powder under compaction is observed by characterizing the pellet length, green density, microstructure, and the compression strength using micrometer SEM, and Universal Testing Machine. The results of the experiment show that the UO 2 powder ex-AUC has particles of spherical type and separate individually which provide the flowable characteristic, important for the die filling aspect during compaction step. The UO 2 powder ex-ADU is more or less agglomerated and contains very fine particles causing the difficulty in pressing. Therefore the green density resulted from UO 2 ex-AUC (6.415 g/cm 3 ) is higher than UO 2 powder of UO 2 ex-ADU (6.117 g/cm 3 . UO 2 at lower pressure (4 tons/cm 3 ) the compression strength ex-AUC green pellet (47.144 kgf) is lower than UO 2 ex-ADU (63,364 kgf), and at higher temperature the compression strength of ex-AUC (92.86 kgf) is higher than UO 2 ex-ADU (82.664 kgf). It is suggested that UO 2 ex-ADU has to be precompacted and granulated in order to increase its flowability so that the pellet length can easily be controlled during pressing (improve reproducibility). (author)

Active Thermography for the Detection of Defects in Powder Metallurgy Compacts

International Nuclear Information System (INIS)

Benzerrouk, Souheil; Ludwig, Reinhold; Apelian, Diran

2007-01-01

Active thermography is an established NDE technique that has become the method of choice in many industrial applications which require non-contact access to the parts under test. Unfortunately, when conducting on-line infrared (IR) inspection of powder metallic compacts, complications can arise due the generally low emissivity of metals and the thermally noisy environment typically encountered in manufacturing plants. In this paper we present results of an investigation that explores the suitability of active IR imaging of powder metallurgy compacts for the detection of surface and sub-surface defects in the pre-sinter state and in an on-line manufacturing setting to ensure complete quality assurance. Additional off-line tests can be carried out for statistical quality analyses. In this research, the IR imaging of sub-surface defects is based on a transient instrumentation approach that relies on an electric control system which synchronizes and monitors the thermal response due to an electrically generated heat source. Preliminary testing reveals that this newly developed pulsed thermography system can be employed for the detection of subsurface defects in green-state parts. Practical measurements agree well with theoretical predictions. The inspection approach being developed can be used for the testing of green-state compacts as they exit the compaction press at speeds of up to 1,000 parts per hour

Compact and energy saving magnet technology for particle accelerators

International Nuclear Information System (INIS)

Baurichter, A.

2013-01-01

Despite the fact that funding agencies and industrial users of particle accelerators get more and more alerted about costs of civil engineering, installation and operation, only little effort has been put into development of sustainable, energy and cost saving accelerator technology. In order to reduce the total-cost-of ownership of accelerator magnets, operating at high electrical power for twenty years or more, permanent magnet based Green Magnet technology has been developed at a consortium around Danfysik's R and D team. Together with our partners from ISA, Aarhus University, the Aarhus School of Engineering, the company Sintex and Aalborg University all obstacles in applying permanent magnet technology as e.g. thermal drift and inhomogeneities of magnetic fields have been overcome. The first Green Magnet has now been operated for more than half a year in an Accelerator Mass Spectrometry facility at the ETH in Zurich. The performance of this B=0.43T 90 deg. H-type bending magnet and the most recently builtB=1T, 30 deg. C-type Green Magnet for the synchrotron light source ASTRID2 at ISA in Aarhus will be presented. Danfysik also is designing, manufacturing and testing 60 compact magnet systems, developed at MAX-Lab for the new MAXIV 3.0 GeV synchrotron light source. In addition, 12 for the 1.5 GeV light source and another 12 for the new SOLARIS light source in Krakow, Poland are buying built. Up to a dozen or more magnet functions have been integrated into one yoke of these compact magnet systems, which makes the new MAXIV light sources compact, energy saving and at the same time very bright. Test results and design concepts of the new MAXIV and SOLARIS magnets will be presented. (author)

Studies on the sintering of copper powder compacts

International Nuclear Information System (INIS)

Elmasry, M.A.A.; Abadir, M.F.; Mahdy, A.N.; Elkinawy, W.S.

1995-01-01

Solid state sintering behavior of cylindrical compacts, (1 cm diameter and 1 cm height), made of copper powder was studied within a range of compacting pressure of 75 up to 300 MPa, sintering temperature of 600 up to to 900 degree C, and sintering time of 5 up to 60 min in a reducing atmosphere composed of H2 and N 2 gases with a volumetric ratio 3:1. The green and the sintered densities were found to to increase with the compacting pressure. Higher sintering temperature, and time favour increased sintered density. probable mechanisms during the initial stage of sintering were disclosed. It was found that low pressures cause dilation of closed pores, and vice versa. At low pressures and temperatures the surface diffusion mechanism is favoured, While high temperatures favour lattice diffusion mechanism. at high pressures, the lattice diffusion mechanism is suppressed while surface diffusion predominates. Density and hence shrinkage were also found to increase with the increase of sintering time, While its rate increases with the increase of sintering temperature. the influence of sintering conditions on the hardness of the compacts was studied. An increase in hardness, When higher compacting pressures and higher sintering temperatures were adopted, has bee obtained. 11 figs

Modelling and Simulation of Tensile Fracture in High Velocity Compacted Metal Powder

International Nuclear Information System (INIS)

Jonsen, P.; Haeggblad, H.-A.

2007-01-01

In cold uniaxial powder compaction, powder is formed into a desired shape with rigid tools and a die. After pressing, but before sintering, the compacted powder is called green body. A critical property in the metal powder pressing process is the mechanical properties of the green body. Beyond a green body free from defects, desired properties are high strength and uniform density. High velocity compaction (HVC) using a hydraulic operated hammer is a production method to form powder utilizing a shock wave. Pre-alloyed water atomised iron powder has been HVC-formed into circular discs with high densities. The diametral compression test also called the Brazilian disc test is an established method to measure tensile strength in low strength material like e.g. rock, concrete, polymers and ceramics. During the test a thin disc is compressed across the diameter to failure. The compression induces a tensile stress perpendicular to the compressed diameter. In this study the test have been used to study crack initiation and the tensile fracture process of HVC-formed metal powder discs with a relative density of 99%. A fictitious crack model controlled by a stress versus crack-width relationship is utilized to model green body cracking. Tensile strength is used as a failure condition and limits the stress in the fracture interface. The softening rate of the model is obtained from the corresponding rate of the dissipated energy. The deformation of the powder material is modelled with an elastic-plastic Cap model. The characteristics of the tensile fracture development of the central crack in a diametrically loaded specimen is numerically studied with a three dimensional finite element simulation. Results from the finite element simulation of the diametral compression test shows that it is possible to simulate fracturing of HVC-formed powder. Results from the simulation agree reasonably with experiments

Effects of Compact Urban Development on Air Pollution: Empirical Evidence from Korea

Directory of Open Access Journals (Sweden)

Hee-Sun Cho

2014-09-01

Full Text Available This study investigates the effects of compact urban development on air pollution, taking into account both the spatial distribution of pollutants resulting from an increase in inner urban densities and the dispersion of pollutants associated with an increase in outer green open spaces. The empirical analysis is based upon a panel data model covering 17 cities in Korea from 1996–2009; this approach is used because urban air pollution is influenced by spatial and temporal changes. Measuring the air pollution level by distance from city centers demonstrates that the spatial concentration of emission sources does not necessarily increase air pollution levels. The two-way fixed effects model, which is employed to control both individual (regional and time effects, shows that SO2 decreases as the proportion of green area increases, while a rise in net density leads to an increase of NO2. Both effects are observed in the case of CO dispersion by green area as well as emission source concentration by high densities. Therefore, there is no clear impact of compact urban development on air quality, which is instead related to pollutant-specific characteristics and the emission source.

Forging loads, deformation modes and fracture in axi-symmetrric closed die cold forging of sintered aluminium powder compacts

International Nuclear Information System (INIS)

Butt, M.A.; Ali, L.

2003-01-01

An experimental investigation into closed-die cold forging of sintered aluminium powder rod- shaped compacts was carried out. Axi-symmetric components were forged from sintered powder preforms with different initial diameter to height ratios. Different compaction pressures, sintering and lubrication conditions were used as variables during the investigations. Detailed observations were made on green/sintered density, compaction defects, forging loads, deformation modes and on the onset of fracture during progressive forging of sintered powder compacts. Experimental results obtained during the investigations have been presented and discussed in detail. (author)

Cold compaction behavior of nano-structured Nd–Fe–B alloy powders prepared by different processes

International Nuclear Information System (INIS)

Liu, Xiaoya; Hu, Lianxi; Wang, Erde

2013-01-01

Graphical abstract: Relative density enhancement and nanocrystallization of Nd 2 Fe 14 B phase are two major effective means to improve magnetic properties. Since the matrix Nd 2 Fe 14 B phase in the starting Nd–Fe–B alloy can be disproportionated into a nano-structured mixture of NdH 2.7 , Fe 2 B, and α-Fe phases during mechanical milling in hydrogen. It is thus important to study the densification behavior of nanocrystalline powders to evaluate and predict the cold compactibility of powders. By comparison with the as milled as well as melt-spun Nd 16 Fe 76 B 8 alloy powders, we find that the as-disproportionated Nd 16 Fe 76 B 8 alloy powder exhibits the best cold compactibility. As evident from the illustration presented below, compaction parameters (representing the powder compactibility) have been determined by fitting density–pressure data with double logarithm compaction equation. Densification mechanisms involved during cold compaction process are clarified in our work by referring to microstructure observation of samples prepared by various methods. As a result, highly densified green magnet compact can be obtained by cold pressing of as-disproportionated NdFeB alloy powders. Highlights: ► Nano-structured disproportionated Nd–Fe–B alloy powders by mechanical milling in hydrogen. ► Highly densified green magnet compact by cold pressing of as-disproportionated Nd–Fe–B alloy powders. ► Density–pressure data fitted well by an empirical powder compaction model. ► As-disproportionated powder showed better compactibility than as milled and melt-spun counterparts. ► The effects of physical properties on powder compactibility and densification mechanisms are clarified. - Abstract: The compaction behavior of nano-structured Nd 16 Fe 76 B 8 (atomic ratio) alloy powders, which were prepared by three different processing routes including melt spinning, mechanical milling in argon, and mechanically activated disproportionation by milling in

Acoustic emission during the compaction of brittle UO2 particles

International Nuclear Information System (INIS)

Hegron, Lise

2014-01-01

One of the options considered for recycling minor actinides is to incorporate about 10% to UO 2 matrix. The presence of open pores interconnected within this fuel should allow the evacuation of helium and fission gases to prevent swelling of the pellet and ultimately its interaction with the fuel clad surrounding it. Implementation of minor actinides requires working in shielded cell, reducing their retention and outlawing additions of organic products. The use of fragmentable particles of several hundred micrometers seems a good solution to control the microstructure of the green compacts and thus control the open porosity after sintering. The goal of this study is to monitor the compaction of brittle UO 2 particles by acoustic emission and to link the particle characteristics to the open porosity obtained after the compact sintering. The signals acquired during tensile strength tests on individual granules and compacts show that the acoustic emission allows the detection of the mechanism of fragmentation and enables identification of a characteristic waveform of this fragmentation. The influences of compaction stress, of the initial particle size distribution and of the internal cohesion of the granules, on the mechanical strength of the compact and on the microstructure and open porosity of the sintered pellets, are analyzed. By its ability to identify the range of fragmentation of the granules during compaction, acoustic emission appears as a promising technique for monitoring the compaction of brittle particles in the manufacture of a controlled porosity fuel. (author) [fr

Stochastic models for turbulent reacting flows

Energy Technology Data Exchange (ETDEWEB)

Kerstein, A. [Sandia National Laboratories, Livermore, CA (United States)

1993-12-01

The goal of this program is to develop and apply stochastic models of various processes occurring within turbulent reacting flows in order to identify the fundamental mechanisms governing these flows, to support experimental studies of these flows, and to further the development of comprehensive turbulent reacting flow models.

Cold compaction behavior of nano-structured Nd-Fe-B alloy powders prepared by different processes

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaoya [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Hu, Lianxi, E-mail: hulx@hit.edu.cn [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China); Wang, Erde [School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001 (China)

2013-02-25

Graphical abstract: Relative density enhancement and nanocrystallization of Nd{sub 2}Fe{sub 14}B phase are two major effective means to improve magnetic properties. Since the matrix Nd{sub 2}Fe{sub 14}B phase in the starting Nd-Fe-B alloy can be disproportionated into a nano-structured mixture of NdH{sub 2.7}, Fe{sub 2}B, and {alpha}-Fe phases during mechanical milling in hydrogen. It is thus important to study the densification behavior of nanocrystalline powders to evaluate and predict the cold compactibility of powders. By comparison with the as milled as well as melt-spun Nd{sub 16}Fe{sub 76}B{sub 8} alloy powders, we find that the as-disproportionated Nd{sub 16}Fe{sub 76}B{sub 8} alloy powder exhibits the best cold compactibility. As evident from the illustration presented below, compaction parameters (representing the powder compactibility) have been determined by fitting density-pressure data with double logarithm compaction equation. Densification mechanisms involved during cold compaction process are clarified in our work by referring to microstructure observation of samples prepared by various methods. As a result, highly densified green magnet compact can be obtained by cold pressing of as-disproportionated NdFeB alloy powders. Highlights: Black-Right-Pointing-Pointer Nano-structured disproportionated Nd-Fe-B alloy powders by mechanical milling in hydrogen. Black-Right-Pointing-Pointer Highly densified green magnet compact by cold pressing of as-disproportionated Nd-Fe-B alloy powders. Black-Right-Pointing-Pointer Density-pressure data fitted well by an empirical powder compaction model. Black-Right-Pointing-Pointer As-disproportionated powder showed better compactibility than as milled and melt-spun counterparts. Black-Right-Pointing-Pointer The effects of physical properties on powder compactibility and densification mechanisms are clarified. - Abstract: The compaction behavior of nano-structured Nd{sub 16}Fe{sub 76}B{sub 8} (atomic ratio) alloy

Mechanism for Self-Reacted Friction Stir Welding

Science.gov (United States)

Venable, Richard; Bucher, Joseph

2004-01-01

A mechanism has been designed to apply the loads (the stirring and the resection forces and torques) in self-reacted friction stir welding. This mechanism differs somewhat from mechanisms used in conventional friction stir welding, as described below. The tooling needed to apply the large reaction loads in conventional friction stir welding can be complex. Self-reacted friction stir welding has become popular in the solid-state welding community as a means of reducing the complexity of tooling and to reduce costs. The main problems inherent in self-reacted friction stir welding originate in the high stresses encountered by the pin-and-shoulder assembly that produces the weld. The design of the present mechanism solves the problems. The mechanism includes a redesigned pin-and-shoulder assembly. The welding torque is transmitted into the welding pin by a square pin that fits into a square bushing with set-screws. The opposite or back shoulder is held in place by a Woodruff key and high-strength nut on a threaded shaft. The Woodruff key reacts the torque, while the nut reacts the tensile load on the shaft.

A compact frequency stabilized telecom laser diode for space applications

Science.gov (United States)

Philippe, C.; Holleville, D.; Le Targat, R.; Wolf, P.; Leveque, T.; Le Goff, R.; Martaud, E.; Acef, O.

2017-09-01

We report on a Telecom laser diode (LD) frequency stabilization to a narrow iodine hyperfine line in the green range, after frequency tripling process using fibered nonlinear waveguide PPLN crystals. We have generated up to 300 mW optical power in the green range ( 514 nm) from 800 mW of infrared power ( 1542 nm), corresponding to a nonlinear conversion efficiency h = P3?/P? 36%. Less than 10 mW of the generated green power are used for Doppler-free spectroscopy of 127I2 molecular iodine, and -therefore- for the frequency stabilization purpose. The frequency tripling optical setup is very compact (test the potential of this new frequency standard based on the couple "1.5 ?m laser / iodine molecule". We have already demonstrated a preliminary frequency stability of 4.8 x 10-14 ? -1/2 with a minimum value of 6 x 10-15 reached after 50 s of integration time, conferred to a laser diode operating at 1542.1 nm. We focus now our efforts to expand the frequency stability to a longer integration time in order to meet requirements of many space experiments, such earth gravity missions, inters satellites links or space to ground communications. Furthermore, we investigate the potential of a new approach based on frequency modulation technique (FM), associated to a 3rd harmonic detection of iodine lines to increase the compactness of the optical setup.

Calorimetry of non-reacting systems

CERN Document Server

McCullough, John P

2013-01-01

Experimental Thermodynamics, Volume 1: Calorimetry of Non-Reacting Systems covers the heat capacity determinations for chemical substances in the solid, liquid, solution, and vapor states, at temperatures ranging from near the absolute zero to the highest at which calorimetry is feasible.This book is divided into 14 chapters. The first four chapters provide background information and general principles applicable to all types of calorimetry of non-reacting systems. The remaining 10 chapters deal with specific types of calorimetry. Most of the types of calorimetry treated are developed over a c

Chopped hemp: Logistics, compaction and financial viability; Logistik, komprimering och ekonomi angaaende hackad hampa

Energy Technology Data Exchange (ETDEWEB)

Soederstroem, Yvonne

2010-05-15

In this project compaction and logistics experiments were conducted using chopped hemp. The aim was to reduce the hemp to 250 kg/m3, as well as to identify the best possible logistical system for compaction and subsequent transportation to the end-user in terms of cost and environmental impact. The project primarily focused on landowners and power companies. Other stakeholders are industries, universities and other ongoing projects in related fields. These studies have shown that it is possible to compact chopped hemp from a density of 60 kg dm/m3 (0.30 MWh/m3) when harvesting directly into the container, to a density of 202 kg dm/m3 (1.01 MWh/m3) using the baler. The original compaction target was a volumetric weight of 250 kg/m3. It was determined that straw and hemp react similarly to compaction. This project has demonstrated that the transport rig system has the best potential for large-scale use as compared with the alternate systems used. According to our calculations, the transport rig was the most cost-effective system measured in kronor per energy content. In addition, this system is also flexible. From an environmental standpoint, however, the energy balance showed that the container system was slightly superior

Improved compaction of ZnO nano-powder triggered by the presence of acetate and its effect on sintering.

Science.gov (United States)

Dargatz, Benjamin; Gonzalez-Julian, Jesus; Guillon, Olivier

2015-04-01

The retention of nanocrystallinity in dense ceramic materials is still a challenge, even with the application of external pressure during sintering. The compaction behavior of high purity and acetate enriched zinc oxide (ZnO) nano-powders was investigated. It was found that acetate in combination with water plays a key role during the compaction into green bodies at moderate temperatures. Application of constant pressure resulted in a homogeneous green body with superior packing density (86% of theoretical value) at moderate temperature (85 °C) in the presence of water. In contrast, no improvement in density could be achieved if pure ZnO powder was used. This compaction behavior offers superior packing of the particles, resulting in a high relative density of the consolidated compact with negligible coarsening. Dissolution accompanying creep diffusion based matter transport is suggested to strongly support reorientation of ZnO particles towards densities beyond the theoretical limit for packing of ideal monosized spheres. Finally, the sintering trajectory reveals that grain growth is retarded compared to conventional processing up to 90% of theoretical density. Moreover, nearly no radial shrinkage was observed after sinter-forging for bodies performed with this advanced processing method.

Eco-friendly synthesis for MCM-41 nanoporous materials using the non-reacted reagents in mother liquor.

Science.gov (United States)

Ng, Eng-Poh; Goh, Jia-Yi; Ling, Tau Chuan; Mukti, Rino R

2013-03-04

Nanoporous materials such as Mobil composite material number 41 (MCM-41) are attractive for applications such as catalysis, adsorption, supports, and carriers. Green synthesis of MCM-41 is particularly appealing because the chemical reagents are useful and valuable. We report on the eco-friendly synthesis of MCM-41 nanoporous materials via multi-cycle approach by re-using the non-reacted reagents in supernatant as mother liquor after separating the solid product. This approach was achieved via minimal requirement of chemical compensation where additional fresh reactants were added into the mother liquor followed by pH adjustment after each cycle of synthesis. The solid product of each successive batch was collected and characterized while the non-reacted reagents in supernatant can be recovered and re-used to produce subsequent cycle of MCM-41. The multi-cycle synthesis is demonstrated up to three times in this research. This approach suggests a low cost and eco-friendly synthesis of nanoporous material since less waste is discarded after the product has been collected, and in addition, product yield can be maintained at the high level.

A Compact Source of Flash-Corona Discharge for Biomedical Applications

Science.gov (United States)

Moshkunov, S. I.; Khomich, V. Yu.; Shershunova, E. A.

2018-01-01

A compact source of low-temperature plasma for biological and medical applications is proposed, which operates at kilohertz frequencies in the regime of flash-corona discharge with an energy of 0.1 mJ/pulse. The plasma source was tested in application to plasma pretreatment of green salad seeds. Plasma-treated seeds exhibited increased (by about 25%) germination speed as compared to that in the untreated control.

Pump-Fed, Compact, High Performance Green Propulsion System for Secondary Payloads, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Flight Works is proposing to expand its micropump-fed propulsion technology to the development of a low cost, compact, low tank pressure, high performance LPM-103S...

A Parallel Multiblock Structured Grid Method with Automated Interblocked Unstructured Grids for Chemically Reacting Flows

Science.gov (United States)

Spiegel, Seth Christian

An automated method for using unstructured grids to patch non- C0 interfaces between structured blocks has been developed in conjunction with a finite-volume method for solving chemically reacting flows on unstructured grids. Although the standalone unstructured solver, FVFLO-NCSU, is capable of resolving flows for high-speed aeropropulsion devices with complex geometries, unstructured-mesh algorithms are inherently inefficient when compared to their structured counterparts. However, the advantages of structured algorithms in developing a flow solution in a timely manner can be negated by the amount of time required to develop a mesh for complex geometries. The global domain can be split up into numerous smaller blocks during the grid-generation process to alleviate some of the difficulties in creating these complex meshes. An even greater abatement can be found by allowing the nodes on abutting block interfaces to be nonmatching or non-C 0 continuous. One code capable of solving chemically reacting flows on these multiblock grids is VULCAN, which uses a nonconservative approach for patching non-C0 block interfaces. The developed automated unstructured-grid patching algorithm has been installed within VULCAN to provide it the capability of a fully conservative approach for patching non-C0 block interfaces. Additionally, the FVFLO-NCSU solver algorithms have been deeply intertwined with the VULCAN source code to solve chemically reacting flows on these unstructured patches. Finally, the CGNS software library was added to the VULCAN postprocessor so structured and unstructured data can be stored in a single compact file. This final upgrade to VULCAN has been successfully installed and verified using test cases with particular interest towards those involving grids with non- C0 block interfaces.

SEPARATION OF THE INTER- AND INTRA-PARTICLE POROSITY IN IMAGES OF POWDER COMPACTS

Directory of Open Access Journals (Sweden)

Jacques Lacaze

2011-05-01

Full Text Available Powder metallurgy is a highly developed and cheap method of manufacturing reliable materials, either metallic, ceramic or composite. This process was used to make green compacts of iron powders with a high porosity level. This study is part of a project aimed at describing the relationships between mechanical properties and morphological features of such compacts, with particular attention paid to the shape of the grains and the compaction pressure. In this report, a method is proposed to separate the intra grain porosity from the cavities located between particles. The approach is based on the covariogram of images obtained from the surface of the compacts by means of a laser roughometer. To achieve this separation, a model of the structure is proposed which assumes that the distributions of the grains and of the intra-particle cavities are random and independent. Each distribution is characterized by two parameters. A satisfactory agreement is obtained between experimental and calculated covariograms after identification of these parameters.

Large-Eddy Simulations of Reacting Liquid Spray

Science.gov (United States)

Lederlin, Thomas; Sanjose, Marlene; Gicquel, Laurent; Cuenot, Benedicte; Pitsch, Heinz; Poinsot, Thierry

2008-11-01

Numerical simulation, which is commonly used in many stages of aero-engine design, still has to demonstrate its predictive capability for two-phase reacting flows. This study is a collaboration between Stanford University and CERFACS to perform LES of a realistic spray combustor installed at ONERA, Toulouse. The experimental configuration is computed on the same unstructured mesh with two different solvers: Stanford's CDP code and CERFACS's AVBP code. CDP uses a low-Mach, variable-density solver with implicit time advancement. Droplets are tracked in a Lagrangian point-particle framework. The combustion model uses a flamelet approach, based on two transported scalars, mixture fraction and reaction progress variable. AVBP is a fully compressible solver with explicit time advancement. The liquid phase is described with an Eulerian method. The flame-turbulence interaction is modeled using a dynamically-thickened flame. Results are compared with experimental data for three regimes: purely gaseous non-reacting flow, non-reacting flow with evaporating droplets, reacting flow with droplets. Both simulations show a good agreement with experimental data and also stress the difference and relative advantages of the numerical methods.

Fabrication of hard cermets by in-situ synthesis and infiltration of metal melts into WC powder compacts

Directory of Open Access Journals (Sweden)

Guanghua Liu

2017-12-01

Full Text Available Hard carbide cermets are prepared by in-situ synthesis and infiltration of metal melts into WC powder compacts. Ni–W and Ni–W–Cr metal melts are in-situ synthesized from thermite reactions and infiltrated into WC powder compacts under high-gravity. During the infiltration, W in the metal melts reacts with WC to form W2C, and more W2C and W are observed at the upper parts of the cermets than the lower parts. The cermets show a maximum hardness of 15.4 GPa, which is higher than most commercial cemented carbides, although they are not fully dense and have a porosity of 15–20%.

Green business will remain green

International Nuclear Information System (INIS)

Marcan, P.

2008-01-01

It all started with two words. Climate change. The carbon dioxide trading scheme, which was the politicians' idea on solving the number one global problem, followed. Four years ago, when the project was begun, there was no data for project initiation. Quotas for polluters mainly from energy production and other energy demanding industries were distributed based on spreadsheets, maximum output and expected future development of economies. Slovak companies have had a chance to profit from these arrangements since 2005. Many of them took advantage of the situation and turned the excessive quotas into an extraordinary profit which often reached hundreds of million Sk. The fact that the price of free quotas offered for sale dropped basically to 0 in 2006 only proved that the initial distribution was too generous. And the market reacted to the first official measurements of emissions. Slovak companies also contributed to this development. However, when planning the maximum emission volumes for 2008-2012 period, in spite of the fact that actual data were available, their expectations were not realistic. A glance at the figures in the proposal of the Ministry of Environment is sufficient to realize that there will be no major change in the future. And so for many Slovak companies business with a green future will remain green for the next five years. The state decided to give to selected companies even more free space as far as emissions are concerned. The most privileged companies can expect quotas increased by tens of percent. (author)

Numerical study of multiscale compaction-initiated detonation

Science.gov (United States)

Gambino, J. R.; Schwendeman, D. W.; Kapila, A. K.

2018-02-01

A multiscale model of heterogeneous condensed-phase explosives is examined computationally to determine the course of transient events following the application of a piston-driven stimulus. The model is a modified version of that introduced by Gonthier (Combust Sci Technol 175(9):1679-1709, 2003. https://doi.org/10.1080/00102200302373) in which the explosive is treated as a porous, compacting medium at the macro-scale and a collection of closely packed spherical grains capable of undergoing reaction and diffusive heat transfer at the meso-scale. A separate continuum description is ascribed to each scale, and the two scales are coupled together in an energetically consistent manner. Following piston-induced compaction, localized energy deposition at the sites of intergranular contact creates hot spots where reaction begins preferentially. Reaction progress at the macro-scale is determined by the spatial average of that at the grain scale. A parametric study shows that combustion at the macro-scale produces an unsteady detonation with a cyclical character, in which the lead shock loses strength and is overtaken by a stronger secondary shock generated in the partially reacted material behind it. The secondary shock in turn becomes the new lead shock and the process repeats itself.

Cacao Intensification in Sulawesi: A Green Prosperity Model Project

Energy Technology Data Exchange (ETDEWEB)

Moriarty, K.; Elchinger, M.; Hill, G.; Katz, J.; Barnett, J.

2014-09-01

NREL conducted eight model projects for Millennium Challenge Corporation's (MCC) Compact with Indonesia. Green Prosperity, the largest project of the Compact, seeks to address critical constraints to economic growth while supporting the Government of Indonesia's commitment to a more sustainable, less carbon-intensive future. This study evaluates techniques to improve cacao farming in Sulawesi Indonesia with an emphasis on Farmer Field Schools and Cocoa Development Centers to educate farmers and for train the trainer programs. The study estimates the economic viability of cacao farming if smallholder implement techniques to increase yield as well as social and environmental impacts of the project.

Titanium compacts produced by the pulvimetallurgical hydride-dehydride method for biomedical applications

International Nuclear Information System (INIS)

Barreiro, M M; Grana, D R; Kokubu, G A; Luppo, M I; Mintzer, S; Vigna, G

2010-01-01

Titanium powder production by the hydride-dehydride method has been developed as a non-expensive process. In this work, commercially pure grade two Ti specimens were hydrogenated. The hydrided material was milled in a planetary mill. The hydrided titanium powder was dehydrided and then sieved to obtain a particle size between 37 and 125 μm in order to compare it with a commercial powder produced by chemical reduction with a particle size lower than 150 μm. Cylindrical green compacts were obtained by uniaxial pressing of the powders at 343 MPa and sintering in vacuum. The powders and the density of sintered compacts were characterized, the oxygen content was measured and in vivo tests were performed in the tibia bones of Wistar rats in order to evaluate their biocompatibility. No differences were observed between the materials which were produced either with powders obtained by the hydride-dehydride method or with commercial powders produced by chemical reduction regarding modifications in compactation, sintering and biological behaviour.

Titanium compacts produced by the pulvimetallurgical hydride-dehydride method for biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Barreiro, M M [Materiales Dentales, Facultad de OdontologIa, Universidad de Buenos Aires, Marcelo T de Alvear 2142 (1122), Buenos Aires (Argentina); Grana, D R; Kokubu, G A [PatologIa I. Escuela de OdontologIa, Facultad de Medicina. Asociacion Odontologica Argentina-Universidad del Salvador, Tucuman 1845 (1050) Buenos Aires (Argentina); Luppo, M I; Mintzer, S; Vigna, G, E-mail: mbarreiro@mater.odon.uba.a, E-mail: dgrana@usal.edu.a, E-mail: luppo@cnea.gov.a, E-mail: vigna@cnea.gov.a [Departamento Materiales, Comision Nacional de Energia Atomica, Gral Paz 1499 (B1650KNA), San MartIn, Buenos Aires (Argentina)

2010-04-15

Titanium powder production by the hydride-dehydride method has been developed as a non-expensive process. In this work, commercially pure grade two Ti specimens were hydrogenated. The hydrided material was milled in a planetary mill. The hydrided titanium powder was dehydrided and then sieved to obtain a particle size between 37 and 125{mu}m in order to compare it with a commercial powder produced by chemical reduction with a particle size lower than 150{mu}m. Cylindrical green compacts were obtained by uniaxial pressing of the powders at 343 MPa and sintering in vacuum. The powders and the density of sintered compacts were characterized, the oxygen content was measured and in vivo tests were performed in the tibia bones of Wistar rats in order to evaluate their biocompatibility. No differences were observed between the materials which were produced either with powders obtained by the hydride-dehydride method or with commercial powders produced by chemical reduction regarding modifications in compactation, sintering and biological behaviour.

Study on Effects of Different Replacement Rate on Bending Behavior of Big Recycled Aggregate Self Compacting Concrete

Science.gov (United States)

Li, Jing; Guo, Tiantian; Gao, Shuai; Jiang, Lin; Zhao, Zhijun; Wang, Yalin

2018-03-01

Big recycled aggregate self compacting concrete is a new type of recycled concrete, which has the advantages of low hydration heat and green environmental protection, but its bending behavior can be affected by different replacement rate. Therefor, in this paper, the research status of big Recycled aggregate self compacting concrete was systematically introduced, and the effect of different replacement rate of big recycled aggregate on failure mode, crack distribution and bending strength of the beam were studied through the bending behavior test of 4 big recycled aggregate self compacting concrete beams. The results show that: The crack distribution of the beam can be affected by the replacement rate; The failure modes of big recycled aggregate beams are the same as those of ordinary concrete; The plane section assumption is applicable to the big recycled aggregate self compacting concrete beam; The higher the replacement rate, the lower the bending strength of big recycled aggregate self compacting concrete beams.

Euclidean scalar Green's functions near the black hole and black brane horizons

International Nuclear Information System (INIS)

Haba, Z

2009-01-01

We discuss approximations of the Riemannian geometry near the horizon. If a (D + 1)-dimensional manifold N has a bifurcate Killing horizon then we approximate N by a product of the two-dimensional Rindler space R 2 and a (D - 1)-dimensional Riemannian manifold M. We obtain approximate formulae for scalar Green's functions. We study the behavior of the Green's functions near the horizon and their dimensional reduction. We show that if M is compact then the Green's function near the horizon can be approximated by the Green's function of the two-dimensional quantum field theory. The correction term is exponentially small away from the horizon. We extend the results to black brane solutions of supergravity in 10 and 11 dimensions. The near-horizon geometry can be approximated by N=AdS p xS q . We discuss the Euclidean Green's functions on N and their behavior near the horizon.

Study of transport and micro-structural properties of magnesium di-boride strand under react and bend mode and bend and react mode

International Nuclear Information System (INIS)

Kundu, Ananya; Das, Subrat Kumar; Bano, Anees; Pradhan, Subrata

2015-01-01

I-V characterization of commercial multi-filamentary Magnesium Di-Boride (MgB 2 ) wire of diameter 0.83 mm were studied in cryocooler based self-field characterization system under both react and bent mode and bent and react mode for a range of temperature 6 K - 25 K. This study is of practical technical relevance where the heat treatment of the superconducting wire makes the sample less flexible for winding in magnet and in other applications. There are limited reported data, available on degradation of MgB 2 wire with bending induced strain in react and wind and wind and react method. In the present work the bending diameter were varied from 80 mm to 20 mm in the interval of 10 mm change of bending diameter and for each case critical current (Ic) of the strand is measured for the above range of temperature. An ETP copper made customized sample holder for mounting the MgB 2 strand was fabricated and is thermally anchored to the cooling stage of the cryocooler. It is seen from the experimental data that in react and bent mode the critical current degrades from 105 A to 87 A corresponding to bending diameter of 80 mm and 20 mm respectively. The corresponding bending strain was analytically estimated and compared with the simulation result. It is also observed that in react and bent mode, the degradation of the transport property of the strand is less as compared to react and bent mode. For bent and react mode in the same sample, the critical current (Ic) was measured to be ∼145 A at 15 K for bending diameter of 20 mm. Apart from studying the bending induced strain on MgB 2 strand, the tensile test of the strand at RT was carried out. The electrical characterizations of the samples were accompanied by the microstructure analyses of the bent strand to examine the bending induced degradation in the grain structure of the strand. All these experimental findings are expected to be used as input to fabricate prototype MgB 2 based magnet. (author)

Towards green loyalty: the influences of green perceived risk, green image, green trust and green satisfaction

Science.gov (United States)

Chrisjatmiko, K.

2018-01-01

The paper aims to present a comprehensive framework for the influences of green perceived risk, green image, green trust and green satisfaction to green loyalty. The paper also seeks to account explicitly for the differences in green perceived risk, green image, green trust, green satisfaction and green loyalty found among green products customers. Data were obtained from 155 green products customers. Structural equation modeling was used in order to test the proposed hypotheses. The findings show that green image, green trust and green satisfaction has positive effects to green loyalty. But green perceived risk has negative effects to green image, green trust and green satisfaction. However, green perceived risk, green image, green trust and green satisfaction also seems to be a good device to gain green products customers from competitors. The contributions of the paper are, firstly, a more complete framework of the influences of green perceived risk, green image, green trust and green satisfaction to green loyalty analyses simultaneously. Secondly, the study allows a direct comparison of the difference in green perceived risk, green image, green trust, green satisfaction and green loyalty between green products customers.

Analysis of laboratory compaction methods of roller compacted concrete

Science.gov (United States)

Trtík, Tomáš; Chylík, Roman; Bílý, Petr; Fládr, Josef

2017-09-01

Roller-Compacted Concrete (RCC) is an ordinary concrete poured and compacted with machines typically used for laying of asphalt road layers. One of the problems connected with this technology is preparation of representative samples in the laboratory. The aim of this work was to analyse two methods of preparation of RCC laboratory samples with bulk density as the comparative parameter. The first method used dynamic compaction by pneumatic hammer. The second method of compaction had a static character. The specimens were loaded by precisely defined force in laboratory loading machine to create the same conditions as during static rolling (in the Czech Republic, only static rolling is commonly used). Bulk densities obtained by the two compaction methods were compared with core drills extracted from real RCC structure. The results have shown that the samples produced by pneumatic hammer tend to overestimate the bulk density of the material. For both compaction methods, immediate bearing index test was performed to verify the quality of compaction. A fundamental difference between static and dynamic compaction was identified. In static compaction, initial resistance to penetration of the mandrel was higher, after exceeding certain limit the resistance was constant. This means that the samples were well compacted just on the surface. Specimens made by pneumatic hammer actively resisted throughout the test, the whole volume was uniformly compacted.

Reacting plasma project at IPP Japan

International Nuclear Information System (INIS)

Miyahara, A.; Momota, H.; Hamada, Y.; Kawamura, K.; Akimune, H.

1981-01-01

Contributed papers of the seminar on burning plasma held at UCLA are collected. Paper on ''overview of reacting plasma project'' described aim and philosophy of R-Project in Japan. Paper on ''Burning plasma and requirements for design'' gave theoretical aspect of reacting plasma physics while paper on ''plasma container, heating and diagnostics'' treated experimental aspect. Tritium handling is essential for the next step experiment; therefore, paper on ''Tritium problems in burning plasma experiments'' took an important part of this seminar. As appendix, paper on ''a new type of D - ion source using Si-semiconductor'' was added because such an advanced R and D work is essential for R-Project. (author)

The Cyclohexanol Cycle and Synthesis of Nylon 6,6: Green Chemistry in the Undergraduate Organic Laboratory

Science.gov (United States)

Dintzner, Matthew R.; Kinzie, Charles R.; Pulkrabek, Kimberly; Arena, Anthony F.

2012-01-01

A one-term synthesis project that incorporates many of the principles of green chemistry is presented for the undergraduate organic laboratory. In this multistep scheme of reactions, students react, recycle, and ultimately convert cyclohexanol to nylon 6,6. The individual reactions in the project employ environmentally friendly methodologies, and…

Cross-reacting and heterospecific monoclonal antibodies produced against arabis mosaic nepovirus.

Science.gov (United States)

Frison, E A; Stace-Smith, R

1992-10-01

Monoclonal antibodies (MAbs) were produced against arabis mosaic nepovirus (AMV). A hybridoma screening procedure was applied which involved the testing of culture supernatants, before the hybridomas were cloned to single cell lines, for their reaction with eight nepoviruses [AMV, cherry leafroll virus (CLRV), grapevine fanleaf virus (GFLV), peach rosette mosaic virus, raspberry ringspot virus (RRSV), tobacco ringspot virus, tomato black ring virus (TBRV) and tomato ringspot virus]. In addition to AMV-specific MAbs, this screening technique has allowed the selection of two cross-reacting MAbs: one reacting with AMV and GFLV, and one reacting with AMV and RRSV. This is the first report of MAbs cross-reacting with these nepoviruses. In addition, five heterospecific MAbs (HS-MAbs) could be selected: two reacting with RRSV, two with CLRV and one with TBRV. The usefulness of the screening technique that was applied for the selection of cross-reacting MAbs and HS-MAbs, and the potential use of such antibodies are discussed.

Degradation Kinetics of Carbon Tetrachloride by Sulfate Green Rust as Influenced by pH and Copper Ions (Stillwater)

Science.gov (United States)

Chlorinated solvents such as trichloroethene (TCE, C2HCl3) and carbon tetrachloride (CT, CCl4) are priority groundwater contaminants at many EPA field sites. Green rust (GR) minerals are important corrosion products of zerovalent iron (Fe0) that has been used in permeable react...

Green Nanotechnology in Nordic Construction - Eco-innovation strategies and Dynamics in nordic Window Chains

DEFF Research Database (Denmark)

Andersen, Maj Munch; Sandén, Björn A.; Palmberg, Christopher

This project analyzes Nordic trends in the development and industrial uptake of green nanotechno-logy in construction. The project applies an evolutionary economic perspective in analyzing the innovation dynamics and firm strategies in the window value chains in three Nordic countries, Denmark......, Finland and Sweden. Hence the project investigates two pervasive parallel market trends: The emergence of the green market and the emergence of nanotechnology. The analysis investigates how a traditional economic sector such as the construction sector reacts to such major trends. Conclusions are multiple...... of nanotechnology in the construction sector in the Nordic countries we do find quite a high number of nanotech applications in the Nordic window chains. Eco-innovation is influencing strongly on the nanotech development. We see several examples of nano-enabled smart, multifunctional green solutions in the Nordic...

Fungal decay resistance of wood reacted with phosphorus pentoxide-amine system

Science.gov (United States)

Hong-Lin Lee; George C. Chen; Roger M. Rowell

2004-01-01

Resistance of wood reacted in situ with phosphorus pentoxide-amine to the brown-rot fungus Gloeophyllum trabeum and white-rot fungus Trametes versicolor was examined. Wood reacted with either octyl, tribromo, or nitro derivatives were more resistant to both fungi. Threshold retention values of phosphoramide-reacted wood to white-rot fungus T. versicolor ranged from 2.9...

The REACT Project

DEFF Research Database (Denmark)

Bloch, Paul; Blystad, Astrid; Byskov, Jens

decisions; and the provision of leadership and the enforcement of conditions. REACT - "REsponse to ACcountable priority setting for Trust in health systems" is an EU-funded five-year intervention study, which started in 2006 testing the application and effects of the AFR approach in one district each...... selected disease and programme interventions and services, within general care and on health systems management. Efforts to improve health sector performance have not yet been satisfactory, and adequate and sustainable improvements in health outcomes have not been shown. Priority setting in health systems...... improvements to health systems performance discussed....

Green nanotechnology in Nordic Construction: Eco-innovation strategies and Dynamics in Nordic Window Value Chains

DEFF Research Database (Denmark)

Andersen, Maj Munch

2010-01-01

This project analyzes Nordic trends in the development and industrial uptake of green nanotechno-logy in construction. The project applies an evolutionary economic perspective in analyzing the innovation dynamics and firm strategies in the window value chains in three Nordic countries, Denmark......, Finland and Sweden. Hence the project investigates two pervasive parallel market trends: The emergence of the green market and the emergence of nanotechnology. The analysis investigates how a traditional economic sector such as the construction sector reacts to such major trends. Conclusions are multiple...... of nanotechnology in the construction sector in the Nordic countries we do find quite a high number of nanotech applications in the Nordic window chains. Eco-innovation is influencing strongly on the nanotech development. We see several examples of nano-enabled smart, multifunctional green solutions in the Nordic...

The Compact Muon Solenoid Detector Control System

CERN Multimedia

CERN. Geneva

2012-01-01

The Compact Muon Solenoid (CMS) is a CERN multi-purpose experiment that exploits the physics of the Large Hadron Collider (LHC). The Detector Control System (DCS) ensures a safe, correct and efficient experiment operation, contributing to the recording of high quality physics data. The DCS is programmed to automatically react to the LHC changes. CMS sub-detector’s bias voltages are set depending on the machine mode and particle beam conditions. A protection mechanism ensures that the sub-detectors are locked in a safe mode whenever a potentially dangerous situation exists. The system is supervised from the experiment control room by a single operator. A small set of screens summarizes the status of the detector from the approximately 6M monitored parameters. Using the experience of nearly two years of operation with beam the DCS automation software has been enhanced to increase the system efficiency. The automation allows now for configuration commands that can be used to automatically pre-configure hardwar...

A constitutive theory of reacting electrolyte mixtures

Science.gov (United States)

Costa Reis, Martina; Wang, Yongqi; Bono Maurizio Sacchi Bassi, Adalberto

2013-11-01

A constitutive theory of reacting electrolyte mixtures is formulated. The intermolecular interactions among the constituents of the mixture are accounted for through additional freedom degrees to each constituent of the mixture. Balance equations for polar reacting continuum mixtures are accordingly formulated and a proper set of constitutive equations is derived with basis in the Müller-Liu formulation of the second law of thermodynamics. Moreover, the non-equilibrium and equilibrium responses of the reacting mixture are investigated in detail by emphasizing the inner and reactive structures of the medium. From the balance laws and constitutive relations, the effects of molecular structure of constituents upon the fluid flow are studied. It is also demonstrated that the local thermodynamic equilibrium state can be reached without imposing that the set of independent constitutive variables is time independent, neither spatially homogeneous nor null. The resulting constitutive relations presented throughout this work are of relevance to many practical applications, such as swelling of clays, developing of bio and polymeric membranes, and use of electrorheological fluids in industrial processes. The first author acknowledges financial support from National Counsel of Technological and Scientific Development (CNPq) and German Academic Exchange Service (DAAD).

Characterization of ι-carrageenan and its derivative based green polymer electrolytes

Energy Technology Data Exchange (ETDEWEB)

Jumaah, Fatihah Najirah; Mobaraka, Nadhratun Naiim; Ahmad, Azizan; Ramli, Nazaruddin [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600, Bangi, Selangor Darul Ehsan (Malaysia)

2013-11-27

The new types of green polymer electrolytes based on ι-carrageenan derivative have been prepared. ι-carrageenan act as precursor was reacted with monochloroacetic acid to produce carboxymethyl ι-carrageenan. The powders were characterized by Attenuated Total Reflection Fourier Transform infrared (ATR-FTIR) spectroscopy and {sup 1}H nuclear magnetic resonance (NMR) to confirm the substitution of targeted functional group in ι-carrageenan. The green polymer electrolyte based on ι-carrageenan and carboxymethyl ι-carrageenan was prepared by solution-casting technique. The films were characterized by electrochemical impedance spectroscopy to determine the ionic conductivity. The ionic conductivity ι-carrageenan film were higher than carboxymethyl ι-carrageenan which 4.87 ×10{sup −6} S cm{sup −1} and 2.19 ×10{sup −8} S cm{sup −1}, respectively.

Green functions and dimensional reduction of quantum fields on product manifolds

International Nuclear Information System (INIS)

Haba, Z

2008-01-01

We discuss Euclidean Green functions on product manifolds P=N x M. We show that if M is compact and N is not compact then the Euclidean field on P can be approximated by its zero mode which is a Euclidean field on N. We estimate the remainder of this approximation. We show that for large distances on N the remainder is small. If P=R D-1 x S β , where S β is a circle of radius β, then the result reduces to the well-known approximation of the D-dimensional finite temperature quantum field theory by (D - 1)-dimensional one in the high-temperature limit. Analytic continuation of Euclidean fields is discussed briefly

Compactness and robustness: Applications in the solution of integral equations for chemical kinetics and electromagnetic scattering

Science.gov (United States)

Zhou, Yajun

This thesis employs the topological concept of compactness to deduce robust solutions to two integral equations arising from chemistry and physics: the inverse Laplace problem in chemical kinetics and the vector wave scattering problem in dielectric optics. The inverse Laplace problem occurs in the quantitative understanding of biological processes that exhibit complex kinetic behavior: different subpopulations of transition events from the "reactant" state to the "product" state follow distinct reaction rate constants, which results in a weighted superposition of exponential decay modes. Reconstruction of the rate constant distribution from kinetic data is often critical for mechanistic understandings of chemical reactions related to biological macromolecules. We devise a "phase function approach" to recover the probability distribution of rate constants from decay data in the time domain. The robustness (numerical stability) of this reconstruction algorithm builds upon the continuity of the transformations connecting the relevant function spaces that are compact metric spaces. The robust "phase function approach" not only is useful for the analysis of heterogeneous subpopulations of exponential decays within a single transition step, but also is generalizable to the kinetic analysis of complex chemical reactions that involve multiple intermediate steps. A quantitative characterization of the light scattering is central to many meteoro-logical, optical, and medical applications. We give a rigorous treatment to electromagnetic scattering on arbitrarily shaped dielectric media via the Born equation: an integral equation with a strongly singular convolution kernel that corresponds to a non-compact Green operator. By constructing a quadratic polynomial of the Green operator that cancels out the kernel singularity and satisfies the compactness criterion, we reveal the universality of a real resonance mode in dielectric optics. Meanwhile, exploiting the properties of

Three-dimensional reacting shock–bubble interaction

NARCIS (Netherlands)

Diegelmann, Felix; Hickel, S.; Adams, Nikolaus A.

2017-01-01

We investigate a reacting shock–bubble interaction through three-dimensional numerical simulations with detailed chemistry. The convex shape of the bubble focuses the shock and generates regions of high pressure and temperature, which are sufficient to ignite the diluted stoichiometric

5W intracavity frequency-doubled green laser for laser projection

Science.gov (United States)

Yan, Boxia; Bi, Yong; Li, Shu; Wang, Dongdong; Wang, Dongzhou; Qi, Yan; Fang, Tao

2014-11-01

High power green laser has many applications such as high brightness laser projection and large screen laser theater. A compact and high power green-light source has been developed in diode-pumped solid-state laser based on MgO doped periodically poled LiNbO3 (MgO:PPLN). 5W fiber coupled green laser is achieved by dual path Nd:YVO4/MgO:PPLN intra-cacity frequency-doubled. Single green laser maximum power 2.8W at 532nm is obtained by a 5.5W LD pumped, MgO:PPLN dimensions is 5mm(width)×1mm(thickness)×2mm(length), and the optical to optical conversion efficiency is 51%. The second LD series connected with the one LD, the second path green laser is obtained using the same method. Then the second path light overlap with the first path by the reflection mirrors, then couple into the fiber with a focus mirror. Dual of LD, Nd:YVO4, MgO:PPLN are placed on the same heat sink using a TEC cooling, the operating temperature bandwidth is about 12°C and the stablity is 5% in 96h. A 50×50×17mm3 laser module which generated continuous-wave 5 W green light with high efficiency and width temperature range is demonstrated.

COMPLEX GAS KINEMATICS IN COMPACT, RAPIDLY ASSEMBLING STAR-FORMING GALAXIES

Energy Technology Data Exchange (ETDEWEB)

Amorin, R.; Vilchez, J. M.; Perez-Montero, E. [Instituto de Astrofisica de Andalucia-CSIC, Glorieta de la Astronomia S/N, E-18008 Granada (Spain); Haegele, G. F.; Firpo, V. [Facultad de Ciencias Astronomicas y Geofisicas, Universidad de la Plata, Paseo del Bosque S/N, 1900 La Plata (Argentina); Papaderos, P., E-mail: amorin@iaa.es [Centro de Astrofisica and Faculdade de Ciencias, Universidade do Porto, Rua das Estrelas, 4150-762 Porto (Portugal)

2012-08-01

Deep, high-resolution spectroscopic observations have been obtained for six compact, strongly star-forming galaxies at redshift z {approx} 0.1-0.3, most of them also known as green peas. Remarkably, these galaxies show complex emission-line profiles in the spectral region including H{alpha}, [N II] {lambda}{lambda}6548, 6584, and [S II] {lambda}{lambda}6717, 6731, consisting of the superposition of different kinematical components on a spatial extent of few kiloparsecs: a very broad line emission underlying more than one narrower component. For at least two of the observed galaxies some of these multiple components are resolved spatially in their two-dimensional spectra, whereas for another one a faint detached H{alpha} blob lacking stellar continuum is detected at the same recessional velocity {approx}7 kpc away from the galaxy. The individual narrower H{alpha} components show high intrinsic velocity dispersion ({sigma} {approx} 30-80 km s{sup -1}), suggesting together with unsharped masking Hubble Space Telescope images that star formation proceeds in an ensemble of several compact and turbulent clumps, with relative velocities of up to {approx}500 km s{sup -1}. The broad underlying H{alpha} components indicate in all cases large expansion velocities (full width zero intensity {>=}1000 km s{sup -1}) and very high luminosities (up to {approx}10{sup 42} erg s{sup -1}), probably showing the imprint of energetic outflows from supernovae. These intriguing results underline the importance of green peas for studying the assembly of low-mass galaxies near and far.

O-methylation of natural phenolic compounds based on green chemistry using dimethyl carbonate

Science.gov (United States)

Prakoso, N. I.; Pangestu, P. H.; Wahyuningsih, T. D.

2016-02-01

The alkyl aryl ether compounds, of which methyl eugenol and veratraldehyde are the simplest intermediates can be synthesized by reacting eugenol and vanillin with the green reagent dimethyl carbonate (DMC). The reaction was carried out under mild of temperature and pressure. Excellent yields and selective products were obtained (95-96%) after a few hours. In the end of the reaction, the catalysts (base and Phase Transfer Catalyst) can be recovered and regenerated.

Mouse Embryo Compaction.

Science.gov (United States)

White, M D; Bissiere, S; Alvarez, Y D; Plachta, N

2016-01-01

Compaction is a critical first morphological event in the preimplantation development of the mammalian embryo. Characterized by the transformation of the embryo from a loose cluster of spherical cells into a tightly packed mass, compaction is a key step in the establishment of the first tissue-like structures of the embryo. Although early investigation of the mechanisms driving compaction implicated changes in cell-cell adhesion, recent work has identified essential roles for cortical tension and a compaction-specific class of filopodia. During the transition from 8 to 16 cells, as the embryo is compacting, it must also make fundamental decisions regarding cell position, polarity, and fate. Understanding how these and other processes are integrated with compaction requires further investigation. Emerging imaging-based techniques that enable quantitative analysis from the level of cell-cell interactions down to the level of individual regulatory molecules will provide a greater understanding of how compaction shapes the early mammalian embryo. © 2016 Elsevier Inc. All rights reserved.

Green Transformational Leadership and Green Performance: The Mediation Effects of Green Mindfulness and Green Self-Efficacy

Directory of Open Access Journals (Sweden)

Yu-Shan Chen

2014-09-01

Full Text Available No prior literature explores the influence of green transformational leadership on green performance, thus, this study develops a novel research framework to fill the research gap. This study investigates the influence of green transformational leadership on green performance and discusses the mediation effects of green mindfulness and green self-efficacy by means of structural equation modeling (SEM. The results indicate that green transformational leadership positively influences green mindfulness, green self-efficacy, and green performance. Moreover, this study demonstrates that the positive relationship between green transformational leadership and green performance is partially mediated by the two mediators: green mindfulness and green self-efficacy. It means that green transformational leadership can not only directly affect green performance positively but also indirectly affect it positively through green mindfulness and green self-efficacy. Therefore, firms need to raise their green transformational leadership, green mindfulness, and green self-efficacy to increase their green performance.

Characterization of forced response of density stratified reacting wake

Science.gov (United States)

Pawar, Samadhan A.; Sujith, Raman I.; Emerson, Benjamin; Lieuwen, Tim

2018-02-01

The hydrodynamic stability of a reacting wake depends primarily on the density ratio [i.e., ratio of unburnt gas density (ρu) to burnt gas density (ρb)] of the flow across the wake. The variation of the density ratio from high to low value, keeping ρ u / ρ b > 1 , transitions dynamical characteristics of the reacting wake from a linearly globally stable (or convectively unstable) to a globally unstable mode. In this paper, we propose a framework to analyze the effect of harmonic forcing on the deterministic and synchronization characteristics of reacting wakes. Using the recurrence quantification analysis of the forced wake response, we show that the deterministic behaviour of the reacting wake increases as the amplitude of forcing is increased. Furthermore, for different density ratios, we found that the synchronization of the top and bottom branches of the wake with the forcing signal is dependent on whether the mean frequency of the natural oscillations of the wake (fn) is lesser or greater than the frequency of external forcing (ff). We notice that the response of both branches (top and bottom) of the reacting wake to the external forcing is asymmetric and symmetric for the low and high density ratios, respectively. Furthermore, we characterize the phase-locking behaviour between the top and bottom branches of the wake for different values of density ratios. We observe that an increase in the density ratio results in a gradual decrease in the relative phase angle between the top and bottom branches of the wake, which leads to a change in the vortex shedding pattern from a sinuous (anti-phase) to a varicose (in-phase) mode of the oscillations.

Combining discrete equations method and upwind downwind-controlled splitting for non-reacting and reacting two-fluid computations

International Nuclear Information System (INIS)

Tang, K.

2012-01-01

When numerically investigating multiphase phenomena during severe accidents in a reactor system, characteristic lengths of the multi-fluid zone (non-reactive and reactive) are found to be much smaller than the volume of the reactor containment, which makes the direct modeling of the configuration hardly achievable. Alternatively, we propose to consider the physical multiphase mixture zone as an infinitely thin interface. Then, the reactive Riemann solver is inserted into the Reactive Discrete Equations Method (RDEM) to compute high speed combustion waves represented by discontinuous interfaces. An anti-diffusive approach is also coupled with RDEM to accurately simulate reactive interfaces. Increased robustness and efficiency when computing both multiphase interfaces and reacting flows are achieved thanks to an original upwind downwind-controlled splitting method (UDCS). UDCS is capable of accurately solving interfaces on multi-dimensional unstructured meshes, including reacting fronts for both deflagration and detonation configurations. (author)

Measurements of non-reacting and reacting flow fields of a liquid swirl flame burner

Science.gov (United States)

Chong, Cheng Tung; Hochgreb, Simone

2015-03-01

The understanding of the liquid fuel spray and flow field characteristics inside a combustor is crucial for designing a fuel efficient and low emission device. Characterisation of the flow field of a model gas turbine liquid swirl burner is performed by using a 2-D particle imaging velocimetry(PIV) system. The flow field pattern of an axial flow burner with a fixed swirl intensity is compared under confined and unconfined conditions, i.e., with and without the combustor wall. The effect of temperature on the main swirling air flow is investigated under open and non-reacting conditions. The result shows that axial and radial velocities increase as a result of decreased flow density and increased flow volume. The flow field of the main swirling flow with liquid fuel spray injection is compared to non-spray swirling flow. Introduction of liquid fuel spray changes the swirl air flow field at the burner outlet, where the radial velocity components increase for both open and confined environment. Under reacting condition, the enclosure generates a corner recirculation zone that intensifies the strength of radial velocity. The reverse flow and corner recirculation zone assists in stabilizing the flame by preheating the reactants. The flow field data can be used as validation target for swirl combustion modelling.

Sentinel Gap basalt reacted in a temperature gradient

International Nuclear Information System (INIS)

Charles, R.W.; Bayhurst, G.K.

1983-01-01

Six basalt prisms were reacted in a controlled temperature gradient hydrothermal circulation system for two months. The prisms were centered at 72, 119, 161, 209, 270, and 310 0 C. Total pressure was 1/3 kbar. All prisms showed large weight loss: 5.5% to 14.9%. The matrix micropegmatite and natural nontronitic alteration reacted readily to clays at all temperatures. The first four prisms were coated with a calcium smectite, and the last two prisms were covered with discrete patches of potassium-rich phengite and alkali feldspar. The results indicated that clays may act as adsorbers of various ions

Sentinel Gap basalt reacted in a temperature gradient

International Nuclear Information System (INIS)

Charles, R.W.; Bayhurst, G.K.

1982-01-01

Six basalt prisms were reacted in a controlled temperature gradient hydrothermal circulation system for two months. The prisms are centered at 72, 119, 161, 209, 270, and 310 0 C. Total pressure is 1/3 kbar. All prisms show large weight loss: 5.5% to 14.9%. The matrix micropegmatite and natural nontronitic alteration readily reacts to clays at all temperatures. The first four prisms are coated with a Ca-smectite while the last two prisms are covered with discrete patches of K rich phengite and alkali feldspar. The clays may act as adsorbers of various ions

Linear models for sound from supersonic reacting mixing layers

Science.gov (United States)

Chary, P. Shivakanth; Samanta, Arnab

2016-12-01

We perform a linearized reduced-order modeling of the aeroacoustic sound sources in supersonic reacting mixing layers to explore their sensitivities to some of the flow parameters in radiating sound. Specifically, we investigate the role of outer modes as the effective flow compressibility is raised, when some of these are expected to dominate over the traditional Kelvin-Helmholtz (K-H) -type central mode. Although the outer modes are known to be of lesser importance in the near-field mixing, how these radiate to the far-field is uncertain, on which we focus. On keeping the flow compressibility fixed, the outer modes are realized via biasing the respective mean densities of the fast (oxidizer) or slow (fuel) side. Here the mean flows are laminar solutions of two-dimensional compressible boundary layers with an imposed composite (turbulent) spreading rate, which we show to significantly alter the growth of instability waves by saturating them earlier, similar to in nonlinear calculations, achieved here via solving the linear parabolized stability equations. As the flow parameters are varied, instability of the slow modes is shown to be more sensitive to heat release, potentially exceeding equivalent central modes, as these modes yield relatively compact sound sources with lesser spreading of the mixing layer, when compared to the corresponding fast modes. In contrast, the radiated sound seems to be relatively unaffected when the mixture equivalence ratio is varied, except for a lean mixture which is shown to yield a pronounced effect on the slow mode radiation by reducing its modal growth.

Mini-column assay for rapid detection of malachite green in fish.

Science.gov (United States)

Shalaby, Ali R; Emam, Wafaa H; Anwar, Mervat M

2017-07-01

A simple, rapid and economical mini-column method for detecting malachite green (MG) residue in fish was developed. The method used a column with 2mm ID that was tightly packed with silica gel followed by alumina. Detection of MG was performed by viewing the developed mini-column at visible light by naked eye; where MG was seen as compact green band at the confluence of the silica gel layer with alumina layer. The limit of detection of the assay was 2ng which conform the minimum required performance limit (MRPL). Evaluation utility of the method indicated that all blank and spiked samples at levels below MRPL were assessed as accepted. The intensity of the green band increased whenever MG level in the extract increased; indicated that suggested mini-column technique could be used for semi-quantitative determination of MG in fish samples. The method can be used to select the questionable samples. Copyright © 2017 Elsevier Ltd. All rights reserved.

Strategies for Low-Carbon Green Growth and Urban Management in Korea

Directory of Open Access Journals (Sweden)

Jichung Yang

Full Text Available ABSTRACT: National policies and strategies for low-carbon green growth in Korea are reviewed in this study. Providing standards and guidelines for urban comprehensive planning and management plans is necessary so that the series of plans can deal with possible effects from climate changes. Urban planning guidelines for management and improvements to achieve low carbon green growth were set up and implemented, focusing on institutional and regulatory foundations. These deal with climate change influences on urban planning, reduction of green house gas emissions and elevation of energy efficiency based on plans of land use units. In the case of Seoul city, transit-oriented compact development, public transportation-oriented structure, green space expansion, and pleasant living spaces are implemented in relation to urban structure and land use. We should suggest systematic and comprehensive countermeasures against greenhouse gas emissions and climate changes in terms of spatial structure, transportation systems, natural resource conservation, environment management, energy and open spaces. For the Seoul mega-city, plans show the capabilities of the policy department including many policy tools. Reflecting smart city, ubiquitous city, and U-Eco city concepts and human behavior, we should move towards increasing efficiency and maintaining sustainable economic growth. KEYWORDS: Low-carbon green growth, urban management, Korea, Seoul

Configuration development of a hydraulic press for preloading the toroidal field coils of the Compact Ignition Tokamak

International Nuclear Information System (INIS)

Lee, V.D.

1987-01-01

The Fusion Engineering Design Center (FEDC) is part of a national design team that is developing the conceptual design of the Compact Ignition Tokamak (CIT). To achieve a compact device with the minimum major radius, a vertical preload system is being developed to react the vertical separating force normally carried by the inboard leg of the toroidal field (TF) coils. The preload system is in the form of a hydraulic press. Challenges in the design include the development of hydraulic and structural systems for very large force requirements, which could interface with the CIT machine, while allowing maximum access to the top, bottom, and radial periphery of the machine. Maximum access is necessary for maintenance, diagnostics, instrumentation, and control systems. Materials used in the design must function in the nuclear environment and in the presence of high magnetic fields. This paper presents the configuration development of the hydraulic press used to vertically preload the CIT device

Fabrication and characterization of powder metallurgy tantalum components prepared by high compaction pressure technique

Energy Technology Data Exchange (ETDEWEB)

Kim, Youngmoo [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Agency for Defense Development, Yuseong, P.O. Box 35, Yuseong-gu, Daejeon 34186, Republic of Korea. (Korea, Republic of); Lee, Dongju [Korea Atomic Energy Research Institute, 111 Daedeok-daero, Yuseong-gu, Daejeon 34057 (Korea, Republic of); Hwang, Jaewon [Samsung Electronics, 129 Samsung-ro, Youngtong-gu, Suwon 16677 (Korea, Republic of); Ryu, Ho Jin, E-mail: hojinryu@kaist.ac.kr [Department of Nuclear and Quantum Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of); Hong, Soon Hyung, E-mail: shhong@kaist.ac.kr [Department of Materials Science and Engineering, Korea Advanced Institute of Science and Technology, 291 Daehak-ro, Yuseong-gu, Daejeon 34141 (Korea, Republic of)

2016-04-15

The present study has investigated the consolidation behaviors of tantalum powders during compaction and sintering, and the characteristics of sintered components. For die compaction, the densification behaviors of the powders are simulated by finite element analyses based on the yield function proposed by Shima and Oyane. Accordingly, the green density distribution for coarser particles is predicted to be more uniform because they exhibits higher initial relative tap density owing to lower interparticle friction. It is also found that cold isostatic pressing is capable of producing higher dense compacts compared to the die pressing. However, unlike the compaction behavior, the sintered density of smaller particles is found to be higher than those of coarser ones owing to their higher specific surface area. The maximum sintered density was found to be 0.96 of theoretical density where smaller particles were pressed isostatically at 400 MPa followed by sintering at 2000 °C. Moreover, the effects of processing conditions on grain size and texture were also investigated. The average grain size of the sintered specimen is 30.29 μm and its texture is less than 2 times random intensity. Consequently, it is concluded that the higher pressure compaction technique is beneficial to produce high dense and texture-free tantalum components compared to hot pressing and spark plasma sintering. - Highlights: • Higher Ta density is obtained from higher pressure and sintering temperature. • High compaction method enables P/M Ta to achieve the density of 16.00 g·cm{sup −3}. • A P/M Ta component with fine microstructure and random orientation is developed.

Static properties and impact resistance of a green Ultra-High Performance Hybrid Fibre Reinforced Concrete (UHPHFRC) : experiments and modeling

NARCIS (Netherlands)

Yu, R.; Spiesz, P.R.; Brouwers, H.J.H.

2014-01-01

This paper addresses the static properties and impact resistance of a "green" Ultra-High Performance Hybrid Fibre Reinforced Concrete (UHPHFRC). The design of concrete mixtures aims to achieve a densely compacted cementitious matrix, employing the modified Andreasen & Andersen particle packing

An experimental and numerical study of confined non-reacting and reacting turbulent jets to facilitate homogeneous combustion in industrial furnaces

Science.gov (United States)

Lee, Insu

Confined non-reacting turbulent jets are ideal for recirculating the hot flue gas back into the furnace from an external exhaust duct. Such jets are also used inside the furnace to internally entrain and recirculate the hot flue gas to preheat and dilute the reactants. Both internal and external implementation of confined turbulent jets increase the furnace thermal efficiency. For external implementation, depending on the circumstances, the exhaust gas flow may be co- or counter-flow relative to the jet flow. Inside the furnaces, fuel and air jets are injected separately. To create a condition which can facilitate near homogeneous combustion, these jets have to first mix with the burned gas inside the furnace and simultaneously being heated and diluted prior to combustion. Clearly, the combustion pattern and emissions from reacting confined turbulent jets are affected by jet interactions, mixing and entrainment of hot flue gas. In this work, the flow and mixing characteristics of a non-reacting and reacting confined turbulent jet are investigated experimentally and numerically. This work consists of two parts: (i) A study of flow and mixing characteristics of non-reacting confined turbulent jets with co- or counter-flowing exhaust/flue gas. Here the axial and radial distributions of temperature, velocity and NO concentration (used as a tracer gas) were measured. FLUENT was used to numerically simulate the experimental results. This work provides the basic understanding of the flow and mixing characteristics of confined turbulent jets and develops some design considerations for recirculating flue gas back into the furnace as expressed by the recirculation zone and the stagnation locations. (ii) Numerical calculations of near homogeneous combustion are performed for the existing furnace. The exact geometry of the furnace in the lab is used and the real dimensional boundary conditions are considered. The parameters such as air nozzle diameter (dair), fuel nozzle

Compact Polarimetry Potentials

Science.gov (United States)

Truong-Loi, My-Linh; Dubois-Fernandez, Pascale; Pottier, Eric

2011-01-01

The goal of this study is to show the potential of a compact-pol SAR system for vegetation applications. Compact-pol concept has been suggested to minimize the system design while maximize the information and is declined as the ?/4, ?/2 and hybrid modes. In this paper, the applications such as biomass and vegetation height estimates are first presented, then, the equivalence between compact-pol data simulated from full-pol data and compact-pol data processed from raw data as such is shown. Finally, a calibration procedure using external targets is proposed.

Compaction of FGD-gypsum

NARCIS (Netherlands)

Stoop, B.T.J.; Larbi, J.A.; Heijnen, W.M.M.

1996-01-01

It is shown that it is possible to produce compacted gypsum with a low porosity and a high strength on a laboratory scale by uniaxial compaction of flue gas desulphurization (FGD-) gypsum powder. Compacted FGD-gypsum cylinders were produced at a compaction pres-sure between 50 and 500 MPa yielding

(U) Influence of Compaction Model Form on Planar and Cylindrical Compaction Geometries

Energy Technology Data Exchange (ETDEWEB)

Fredenburg, David A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carney, Theodore Clayton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fichtl, Christopher Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ramsey, Scott D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-01-05

The dynamic compaction response of CeO₂ is examined within the frameworks of the Ramp and P-a compaction models. Hydrocode calculations simulating the dynamic response of CeO₂ at several distinct pressures within the compaction region are investigated in both planar and cylindrically convergent geometries. Findings suggest additional validation of the compaction models is warranted under complex loading configurations.

GREEN CHEMISTRY APPLICATION FOR THE SYNTHESIS OF (1-N-4’-METHOXYBENZYL-1,10-PHENANTHROLINIUM BROMIDE

Directory of Open Access Journals (Sweden)

Maulidan Firdaus

2010-06-01

Full Text Available A simple, energy-efficient, and relatively quick synthetic procedure for the synthesis of (1-N-4'-methoxybenzyl-1,10-phenanthrolinium bromide, based on green chemistry principles has been carried out. The synthesis was started by solvent-free reduction of p-anisaldehyde with NaBH4 to give 4-methoxybenzyl alcohol in 98% yield to be followed by solvent-free treatment of the resulted alcohol with PBr3 to yield 4-methoxybenzyl bromide (86%. Furthermore, the obtained bromide was reacted with 1,10-phenanthroline in acetone at reflux for 12 h to give the phenanthrolinium salt target in 68% yield.   Keywords: green chemistry, p-anisaldehyde, (1-N-4'-methoxybenzyl-1,10-phenanthrolinium bromide

Green Transformational Leadership and Green Performance: The Mediation Effects of Green Mindfulness and Green Self-Efficacy

OpenAIRE

Yu-Shan Chen; Ching-Hsun Chang; Yu-Hsien Lin

2014-01-01

No prior literature explores the influence of green transformational leadership on green performance, thus, this study develops a novel research framework to fill the research gap. This study investigates the influence of green transformational leadership on green performance and discusses the mediation effects of green mindfulness and green self-efficacy by means of structural equation modeling (SEM). The results indicate that green transformational leadership positively influences green min...

ReACT!: An Interactive Educational Tool for AI Planning for Robotics

Science.gov (United States)

Dogmus, Zeynep; Erdem, Esra; Patogulu, Volkan

2015-01-01

This paper presents ReAct!, an interactive educational tool for artificial intelligence (AI) planning for robotics. ReAct! enables students to describe robots' actions and change in dynamic domains without first having to know about the syntactic and semantic details of the underlying formalism, and to solve planning problems using…

Thermal evolution of massive compact objects with dense quark cores

International Nuclear Information System (INIS)

Hess, Daniel; Sedrakian, Armen

2011-01-01

We examine the thermal evolution of a sequence of compact objects containing low-mass hadronic and high-mass quark-hadronic stars constructed from a microscopically motivated equation of state. The dependence of the cooling tracks in the temperature versus age plane is studied on the variations of the gaplessness parameter (the ratio of the pairing gap for red-green quarks to the electron chemical potential) and the magnitude of blue quark gap. The pairing in the red-green channel is modeled assuming an inhomogeneous superconducting phase to avoid tachionic instabilities and anomalies in the specific heat; the blue colored condensate is modeled as a Bardeen-Cooper-Schrieffer (BCS)-type color superconductor. We find that massive stars containing quark matter cool faster in the neutrino-cooling era if one of the colors (blue) is unpaired and/or the remaining colors (red-green) are paired in a inhomogeneous gapless superconducting state. The cooling curves show significant variations along the sequence, as the mass (or the central density) of the models is varied. This feature provides a handle for fine-tuning the models to fit the data on the surface temperatures of same-age neutron stars. In the late-time photon cooling era we observe inversion in the temperature arrangement of models, i.e., stars experiencing fast neutrino cooling are asymptotically hotter than their slowly cooling counterparts.

COMPARISON OF THE MECHANICAL RESPONSE OF POROUS TI-6AL-4V ALLOYS PRODUCED BY DIFFERENT COMPACTION TECHNIQUES

Directory of Open Access Journals (Sweden)

G.İpek Selimoğlu

2017-03-01

Full Text Available Porous Ti-6Al-4V alloys are attractive candidates as implant materials due to their good biocompatibility combined with the porous structure leading to increased osseointegration and decreased stiffness. Accordingly, different processing techniques were employed for the production of Ti-6Al-4V foams in the literature. Among these techniques, sintering with space holder is used to produce porous Ti-6Al-4V alloys in this study. Magnesium was employed as the space holder material because of its relatively low boiling point as well as high oxygen affinity. Two different compaction techniques, die compaction with hydraulic pressing and cold isostatic pressing (CIP, were employed for obtaining green compacts. Both spherical and nonspherical Ti-6Al-4V powders were used to investigate the effect of powder shape on compaction. Processed foams were characterized in terms of both microstructural and mechanical aspects in order to investigate the effect of pressing conditions in combination with powder characteristics. It was observed that NS-CIP foam, which was produced by compacting nonspherical powders by cold isostatic press, has the highest strength. However, the S-DP foam, which was produced by die-pressing of spherical powders, has the highest toughness.

GREEN PACKAGING, GREEN PRODUCT, GREEN ADVERTISING, PERSEPSI, DAN MINAT BELI KONSUMEN

Directory of Open Access Journals (Sweden)

Imam Santoso

2016-12-01

Full Text Available Environmental problems become one of the strategic issues in achieving global competitiveness. One of the issues is products that are made from environmental friendly materials or known as green product. Furthermore, in green products marketing, the company also uses green packaging and green advertising concept. This study aimed to analyze the effect of green packaging, green products, and green advertising on consumer perception and purchasing intention. The study was conducted in Ketawanggede Village, Lowokwaru Sub-district, Malang City. The sampling method used nonprobability accidential sampling techniques. The numbers of respondents were 113 consumers in study site. Data were collected by interview using questionnaires. The method of analysis used Generalized Structured Component Analysis (GSCA. The analysis showed that the green packaging, green products, and green advertising had positive significant influence on consumer perceptions. Meanwhile, green product and consumer perception had positive significant influence on purchasing interest, but the green packaging and green advertising has not found sufficient evidence in influencing purchasing intention.

Modelling of powder die compaction for press cycle optimization

Directory of Open Access Journals (Sweden)

Bayle Jean-Philippe

2016-01-01

Full Text Available A new electromechanical press for fuel pellet manufacturing was built last year in partnership between CEA-Marcoule and ChampalleAlcen. This press was developed to shape pellets in a hot cell via remote handling. It has been qualified to show its robustness and to optimize the compaction cycle, thus obtaining a better sintered pellet profile and limiting damage. We will show you how 400 annular pellets have been produced with good geometry's parameters, based on press settings management. These results are according to a good phenomenological pressing knowledge with Finite Element Modeling calculation. Therefore, during die pressing, a modification in the punch displacement sequence induces fluctuation in the axial distribution of frictional forces. The green pellet stress and density gradients are based on these frictional forces between powder and tool, and between grains in the powder, influencing the shape of the pellet after sintering. The pellet shape and diameter tolerances must be minimized to avoid the need for grinding operations. To find the best parameters for the press settings, which enable optimization, FEM calculations were used and different compaction models compared to give the best calculation/physical trial comparisons. These simulations were then used to predict the impact of different parameters when there is a change in the type of powder and the pellet size, or when the behavior of the press changes during the compaction time. In 2016, it is planned to set up the press in a glove box for UO2 manufacturing qualification based on our simulation methodology, before actual hot cell trials in the future.

Assessment of urban green space structures and their quality from a multidimensional perspective.

Science.gov (United States)

Daniels, Benjamin; Zaunbrecher, Barbara S; Paas, Bastian; Ottermanns, Richard; Ziefle, Martina; Roß-Nickoll, Martina

2018-02-15

Facing the growing amount of people living in cities and, at the same time, the need for a compact and sustainable urban development to mitigate urban sprawl, it becomes increasingly important that green spaces in compact cities are designed to meet the various needs within an urban environment. Urban green spaces have a multitude of functions: Maintaining ecological processes and resulting services, e.g. providing habitat for animals and plants, providing a beneficial city microclimate as well as recreational space for citizens. Regarding these requirements, currently existing assessment procedures for green spaces have some major shortcomings, which are discussed in this paper. It is argued why a more detailed spatial level as well as a distinction between natural and artificial varieties of structural elements is justified and needed and how the assessment of urban green spaces benefits from the multidimensional perspective that is applied. By analyzing a selection of structural elements from an ecological, microclimatic and social perspective, indicator values are derived and a new, holistic metrics 1 is proposed. The results of the integrated analysis led to two major findings: first, that for some elements, the evaluation differs to a great extent between the different perspectives (disciplines) and second, that natural and artificial varieties are, in most cases, evaluated considerably different from each other. The differences between the perspectives call for an integrative planning policy which acknowledges the varying contribution of a structural element to different purposes (ecological, microclimatic, social) as well as a discussion about the prioritization of those purposes. The differences in the evaluation of natural vs. artificial elements verify the assumption that indicators which consider only generic elements fail to account for those refinements and are thus less suitable for planning and assessment purposes. Implications, challenges and

Continuum-Kinetic Hybrid Framework for Chemically Reacting Flows

Data.gov (United States)

National Aeronautics and Space Administration — Predictive modeling of chemically reacting flows is essential for the design and optimization of future hypersonic vehicles. During atmospheric re-entry, complex...

Surface Area, and Oxidation Effects on Nitridation Kinetics of Silicon Powder Compacts

Science.gov (United States)

Bhatt, R. T.; Palczer, A. R.

1998-01-01

Commercially available silicon powders were wet-attrition-milled from 2 to 48 hr to achieve surface areas (SA's) ranging from 1.3 to 70 sq m/g. The surface area effects on the nitridation kinetics of silicon powder compacts were determined at 1250 or 1350 C for 4 hr. In addition, the influence of nitridation environment, and preoxidation on nitridation kinetics of a silicon powder of high surface area (approximately equals 63 sq m/g) was investigated. As the surface area increased, so did the percentage nitridation after 4 hr in N2 at 1250 or 1350 C. Silicon powders of high surface area (greater than 40 sq m/g) can be nitrided to greater than 70% at 1250 C in 4 hr. The nitridation kinetics of the high-surface-area powder compacts were significantly delayed by preoxidation treatment. Conversely, the nitridation environment had no significant influence on the nitridation kinetics of the same powder. Impurities present in the starting powder, and those accumulated during attrition milling, appeared to react with the silica layer on the surface of silicon particles to form a molten silicate layer, which provided a path for rapid diffusion of nitrogen and enhanced the nitridation kinetics of high surface area silicon powder.

Diffusion through statically compacted clay

International Nuclear Information System (INIS)

Ho, C.L.; Shebl, M.A.A.

1994-01-01

This paper presents experimental work on the effect of compaction on contaminant flow through clay liners. The experimental program included evaluation of soil properties, compaction, permeability and solute diffusion. A permeameter was built of non reactive materials to test samples compacted at different water contents and compactive efforts. The flow of a permeating solute, LiCl, was monitored. Effluent samples were collected for solute concentration measurements. The concentrations were measured by performing atomic adsorption tests. The analyzed results showed different diffusion characteristics when compaction conditions changed. At each compactive effort, permeability decreased as molding water content increased. Consequently, transit time (measured at relative concentration 50%) increased and diffusivity decreased. As compactive effort increased for soils compacted dry of optimum, permeability and diffusion decreased. On the other hand, as compactive effort increased for soils compacted wet of optimum, permeability and diffusivity increased. Tortuosity factor was indirectly measured from the diffusion and retardation rate. Tortuosity factor also decreased as placement water content was increased from dry of optimum to wet of optimum. Then decreases were more pronounced for low compactive effort tests. 27 refs., 7 figs., 5 tabs

Self-Compacting Concrete

OpenAIRE

Okamura, Hajime; Ouchi, Masahiro

2003-01-01

Self-compacting concrete was first developed in 1988 to achieve durable concrete structures. Since then, various investigations have been carried out and this type of concrete has been used in practical structures in Japan, mainly by large construction companies. Investigations for establishing a rational mix-design method and self-compactability testing methods have been carried out from the viewpoint of making self-compacting concrete a standard concrete.

Study of Transport and Micro-structural properties of Magnesium Di-Boride Strand under react and bend mode and bend and react mode

International Nuclear Information System (INIS)

Kundu, Ananya; Kumar Das, Subrat; Bano, Anees; Pradhan, Subrata

2017-01-01

I-V characterization of commercial multi-filamentary Magnesium Di-Boride (MgB 2 ) wire of diameter 0.83 mm were studied in Cryocooler at self-field I-V characterization system under both react and bend mode and bend and react mode for a range of temperature 6 K - 25 K. This study is of practical technical relevance where the heat treatment of the superconducting wire makes the wire less flexible for winding in magnet and in other applications. In the present work the bending diameter was varied from 40 mm to 20 mm and for each case critical current (I c ) of the strand is measured for above range of temperature. A customized sample holder is fabricated and thermally anchored with the 2 nd cold stage of Cryocooler. It is observed from the measurement that the strand is more susceptible to degradation for react and bend cases. The transport measurement of the strand was accompanied by SEM analyses of bend samples. Also the tensile strength of the raw strands and the heat treated strands were carried out at room temperature in Universal Testing Machine (UTM) to have an estimate about the limiting winding tension value during magnet fabrication. (paper)

GREEN PACKAGING, GREEN PRODUCT, GREEN ADVERTISING, PERSEPSI, DAN MINAT BELI KONSUMEN

OpenAIRE

Imam Santoso; Rengganis Fitriani

2016-01-01

Environmental problems become one of the strategic issues in achieving global competitiveness. One of the issues is products that are made from environmental friendly materials or known as green product. Furthermore, in green products marketing, the company also uses green packaging and green advertising concept. This study aimed to analyze the effect of green packaging, green products, and green advertising on consumer perception and purchasing intention. The study was conducted in Ketawangg...

Demonstration of Hybrid DSMC-CFD Capability for Nonequilibrium Reacting Flow

Science.gov (United States)

2018-02-09

AFRL-RV-PS- TR-2018-0056 AFRL-RV-PS- TR-2018-0056 DEMONSTRATION OF HYBRID DSMC-CFD CAPABILITY FOR NONEQUILIBRIUM REACTING FLOW Thomas E...4. TITLE AND SUBTITLE Demonstration of Hybrid DSMC-CFD Capability for Nonequilibrium Reacting Flow 5a. CONTRACT NUMBER 5b. GRANT NUMBER FA9453-17-1...simulation codes. The models are based on new ab-intio rate data obtained using state -of-the-art potential energy surfaces for air species. A probability

Sobolev Spaces on Locally Compact Abelian Groups: Compact Embeddings and Local Spaces

Directory of Open Access Journals (Sweden)

Przemysław Górka

2014-01-01

Full Text Available We continue our research on Sobolev spaces on locally compact abelian (LCA groups motivated by our work on equations with infinitely many derivatives of interest for string theory and cosmology. In this paper, we focus on compact embedding results and we prove an analog for LCA groups of the classical Rellich lemma and of the Rellich-Kondrachov compactness theorem. Furthermore, we introduce Sobolev spaces on subsets of LCA groups and study its main properties, including the existence of compact embeddings into Lp-spaces.

Stabilization of compactible waste

International Nuclear Information System (INIS)

Franz, E.M.; Heiser, J.H. III; Colombo, P.

1990-09-01

This report summarizes the results of series of experiments performed to determine the feasibility of stabilizing compacted or compactible waste with polymers. The need for this work arose from problems encountered at disposal sites attributed to the instability of this waste in disposal. These studies are part of an experimental program conducted at Brookhaven National Laboratory (BNL) investigating methods for the improved solidification/stabilization of DOE low-level wastes. The approach taken in this study was to perform a series of survey type experiments using various polymerization systems to find the most economical and practical method for further in-depth studies. Compactible dry bulk waste was stabilized with two different monomer systems: styrene-trimethylolpropane trimethacrylate (TMPTMA) and polyester-styrene, in laboratory-scale experiments. Stabilization was accomplished by wetting or soaking compactible waste (before or after compaction) with monomers, which were subsequently polymerized. Three stabilization methods are described. One involves the in-situ treatment of compacted waste with monomers in which a vacuum technique is used to introduce the binder into the waste. The second method involves the alternate placement and compaction of waste and binder into a disposal container. In the third method, the waste is treated before compaction by wetting the waste with the binder using a spraying technique. A series of samples stabilized at various binder-to-waste ratios were evaluated through water immersion and compression testing. Full-scale studies were conducted by stabilizing two 55-gallon drums of real compacted waste. The results of this preliminary study indicate that the integrity of compacted waste forms can be readily improved to ensure their long-term durability in disposal environments. 9 refs., 10 figs., 2 tabs

Conductivity enhancement via chemical modification of chitosan based green polymer electrolyte

International Nuclear Information System (INIS)

Mobarak, N.N.; Ahmad, A.; Abdullah, M.P.; Ramli, N.; Rahman, M.Y.A.

2013-01-01

The potential of carboxymethyl chitosan as a green polymer electrolyte has been explored. Chitosan produced from partial deacetylation of chitin was reacted with monochloroacetic acid to form carboxymethyl chitosan. A green polymer electrolyte based chitosan and carboxymethyl chitosan was prepared by solution-casting technique. The powder and films were characterized by reflection Fourier transform infrared (ATR-FTIR) spectroscopy, 1 H nuclear magnetic resonance, elemental analysis and X-ray diffraction, electrochemical impedance spectroscopy, and scanning electron microscopy. The shift of wavenumber that represents hydroxyl and amine stretching confirmed the polymer solvent complex formation. The XRD spectra results show that chemical modification of chitosan has improved amorphous properties of chitosan. The ionic conductivity was found to increase by two magnitudes higher with the chemical modification of chitosan. The highest conductivity achieved was 3.6 × 10 −6 S cm −1 for carboxymethyl chitosan at room temperature and 3.7 × 10 −4 S cm −1 at 60 °C

An experimental study on downstream of the transition of the chemically reacting liquid round free jet

International Nuclear Information System (INIS)

Hong, S.D.; Sugii, Y.; Okamoto, K.; Madarame, H.

2002-01-01

An experimental study was conducted on the chemically reacting liquid round free jet, Laser Induced Fluorescence (LIF) technique was adopted to evaluate the diffusion width of the jet into liquid streams. In the fluid engineering, it is very important to evaluate the characteristics of reacting jet for the safety of the nuclear reactor. In this study, the jet profile of downstream region far away from the transition point was evaluated, providing comparisons between reacting and non-reacting jet case. The concentration of the jet solution was varied from 0.01 mol/L to 0.5 mol/L in reacting cases. In the downstream far away from the transition point, the jet profiles between reacting cases and non-reacting cases were visualized quite different. It was concluded that the chemical reaction affects the momentum diffusion of the jet in the downstream region. (author)

Spectrophotometric determination of boron by solvent extraction with 2-hydroxy-2-methylbutyric acid and malachite green

International Nuclear Information System (INIS)

Sato, Shigeya; Uchikawa, Sumio

1984-01-01

A very simple and sensitive method for the spectrophotometric determination of boron was developed. Boron was found to react with 2-hydroxy-2-methylbutyric acid in weak acidic aqueous solution at room temperature to form a complex anion which can be extracted into chlorobenzene with malachite green in a single extraction; boron is determined indirectly by measuring the absorbance of malachite green in the extract at 629 nm. The calibration graph is linear over the range (7.50 x 10 -7 - 2.00 x 10 -5 ) mol dm -3 boron; the apparent molar absorptivity is 6.50 x 10 4 dm 3 mol -1 cm -1 . The method is applied to the determination of micro amounts of boron in natural waters with satisfactory results. (author)

Greens of the European Green Capitals

Science.gov (United States)

Cömertler, Seval

2017-10-01

Well established and maintained green areas have a key role on reaching the high quality of life and sustainability in urban environments. Therefore, green areas must be carefully accounted and evaluated in the urban planning affairs. In this context, the European Green Capitals, which attach a great importance to the green areas, have a great potential to act as a role model for both small and big cities in all around the world. These leading cities (chronologically, Stockholm, Hamburg, Vitoria-Gasteiz, Nantes, Copenhagen, Bristol, Ljubljana, Essen and Nijmegen) are inspiring for the other cities which seek to achieve more sustainable and environmentally friendly places through green areas. From this point of view, the aim of this paper was to investigate the green areas of the European Green Capitals. The paper covered whole European Green Capitals, and the application form of each Green Capital was used as a primary data source. Consequently, the paper put forwarded that the European Green Capitals have considerably large amount and high proportion of green areas. Further, these cities provide an excellent access to the public green areas. As a result of abundant provision and proper distribution, the almost all citizens in most of the Green Capitals live within a distance of 300 meters to a green area. For further researches, the paper suggested that these green capitals should be investigated in terms of their efforts, measures, goals and plans, policies and implications to administer, to protect, to enhance and to expand the green areas.

Cooling compact stars and phase transitions in dense QCD

Energy Technology Data Exchange (ETDEWEB)

Sedrakian, Armen [J.W. Goethe University, Institute for Theoretical Physics, Frankfurt am Main (Germany)

2016-03-15

We report new simulations of cooling of compact stars containing quark cores and updated fits to the Cas A fast cooling data. Our model is built on the assumption that the transient behaviour of the star in Cas A is due to a phase transition within the dense QCD matter in the core of the star. Specifically, the fast cooling is attributed to an enhancement in the neutrino emission triggered by a transition from a fully gapped, two-flavor, red-green color-superconducting quark condensate to a superconducting crystalline or an alternative gapless, color-superconducting phase. The blue-colored condensate is modeled as a Bardeen-Cooper-Schrieffer (BCS)-type color superconductor with spin-one pairing order parameter. We study the sensitivity of the fits to the phase transition temperature, the pairing gap of blue quarks and the timescale characterizing the phase transition (the latter modelled in terms of a width parameter). Relative variations in these parameter around their best-fit values larger than 10{sup -3} spoil the fit to the data. We confirm the previous finding that the cooling curves show significant variations as a function of compact star mass, which allows one to account for dispersion in the data on the surface temperatures of thermally emitting neutron stars. (orig.)

Antimicrobial photodynamic inactivation of Staphylococcus aureus biofilms in bone specimens using methylene blue, toluidine blue ortho and malachite green: An in vitro study.

Science.gov (United States)

Rosa, Luciano Pereira; da Silva, Francine Cristina; Nader, Sumaia Alves; Meira, Giselle Andrade; Viana, Magda Souza

2015-05-01

To evaluate the in vitro effectiveness of APDI with a 660 nm laser combined with methylene blue (MB), toluidine blue ortho (TBO) and malachite green (MG) dyes to inactivate Staphylococcus aureus (ATCC 25923) biofilms in compact and cancellous bone specimens. Eighty specimens of compact and 80 of cancellous bone were contaminated with a standard suspension of the microorganism and incubated for 14 days at 37°C to form biofilms. After this period, the specimens were divided into groups (n=10) according to established treatment: PS-L- (control - no treatment); PSmb+L-, PStbo+L-, PSmg+L- (only MB, TBO or MG for 5 min in the dark); PS-L+ (only laser irradiation for 180 s); and APDImb, APDItbo and APDImg (APDI with MB, TBO or MG for 180 s). The findings were statistically analyzed by ANOVA at 5% significance levels. All experimental treatments showed significant reduction of log CFU/mL S. aureus biofilms when compared with the control group for compact and cancellous bones specimens; the APDI group's treatment was more effective. The APDI carried out for the compact specimens showed better results when compared with cancellous specimens at all times of application. For the group of compact bone, APDImg showed greater reductions in CFU/mL (4.46 log 10). In the group of cancellous bone, the greatest reductions were found in the APDImb group (3.06 log 10). APDI with methylene blue, toluidine blue ortho and malachite green dyes and a 660 nm laser proved to be effective in the inactivation of S. aureus biofilms formed in compact and cancellous bone. Copyright © 2015 Elsevier Ltd. All rights reserved.

Uniaxial backfill block compaction

International Nuclear Information System (INIS)

Koskinen, V.

2012-05-01

The main parts of the project were: to make a literature survey of the previous uniaxial compaction experiments; do uniaxial compaction tests in laboratory scale; and do industrial scale production tests. Object of the project was to sort out the different factors affecting the quality assurance chain of the backfill block uniaxial production and solve a material sticking to mould problem which appeared during manufacturing the blocks of bentonite and cruched rock mixture. The effect of mineralogical and chemical composition on the long term functionality of the backfill was excluded from the project. However, the used smectite-rich clays have been tested for mineralogical consistency. These tests were done in B and Tech OY according their SOPs. The objective of the Laboratory scale tests was to find right material- and compaction parameters for the industrial scale tests. Direct comparison between the laboratory scale tests and industrial scale tests is not possible because the mould geometry and compaction speed has a big influence for the compaction process. For this reason the selected material parameters were also affected by the previous compaction experiments. The industrial scale tests were done in summer of 2010 in southern Sweden. Blocks were done with uniaxial compaction. A 40 tons of the mixture of bentonite and crushed rock blocks and almost 50 tons of Friedland-clay blocks were compacted. (orig.)

Characterization of ceramic powder compacts

International Nuclear Information System (INIS)

Yanai, K.; Ishimoto, S.; Kubo, T.; Ito, K.; Ishikawa, T.; Hayashi, H.

1995-01-01

UO 2 and Al 2 O 3 powder packing structures in cylindrical powder compacts are observed by scanning electron microscopy using polished cross sections of compacts fixed by low viscosity epoxy resin. Hard aggregates which are not destroyed during powder compaction are observed in some of the UO 2 powder compacts. A technique to measure local density in powder compacts is developed based on counting characteristic X-ray intensity by energy dispersive X-ray analysis (EDX). The local density of the corner portion of the powder compact fabricated by double-acting dry press is higher than that of the inner portion. ((orig.))

Study on the dynamic evaluation of the regional green low-carbon transformation in China evidence from Qingdao, Yantai and Weihai

International Nuclear Information System (INIS)

Wang, Chongmei

2016-01-01

Green low-carbon transformation is necessary to achieve sustainable development in “the eighteenth”. Based on the literature review of regional green low-carbon transformation, regional green low-carbon transformation and evaluation framework are defined as the process of building regional green low-carbon transformation. We think that the system innovation is a complex system. By establishing collaborative model of the green transformation of the system innovation, we evaluate dynamically the regional green transformation capacity with data envelopment analysis from changing and developing of the two systems. Which react the efficiency of resource allocation of two systems in-depth analysis of the interaction between the two development of the internal mechanism, and clearing the mechanism between system innovation and transformation capacity. Be corroborated in the case of the practice green transformation of the Jiaodong Peninsula (Qingdao, Yantai and Weihai), strengthening the quantitative study of the depth of the theory and practice in transition. We concluded that: the overall coordination between system innovation and green transformation in Jiaodong Peninsula is good during 2010–2013. System innovation capacity cannot be fully translated into green transformation capacity, and lag weakens the supporting role of other developments in the field innovation for the transition. The situation has become better since 2010. Finally, it focus that the value of research applications and future research direction.

Effect of compacting pressure, powder degassing and thermobaric treatment on densification and properties of nanocrystalline titanium nitride

Directory of Open Access Journals (Sweden)

Andrei V. Kapylou

2009-09-01

Full Text Available The effects of compacting pressure, powder degassing and high pressure sintering temperature and time on the densification and properties of nanocrystalline titanium nitride have been investigated. For this reason, TiN powder with a mean particle size of 55 nm was pressed in the range of compacting pressure from 0.2 to 1.0 GPa and sintered under static pressure of 3.5 GPa in the temperature range of 900–1600°C for 45–120 s. Some of green bodies were degassed in vacuum before sintering. It was shown that samples compacted in the pressure range of 0.2–0.6 GPa have the highest density after the thermobaric treatment. The maximum density (about 97.3 %TD was obtained with degassed samples. Microhardness and microstructure investigations have shown that recrystallization of the TiN nanopowder begins at the sintering temperatures of 1100–1200°C and sintering time less than one minute. The maximum microhardness obtained was 23.2±1.0 GPa and themaximum Young modulus was 370 GPa.

From green architecture to architectural green

DEFF Research Database (Denmark)

Earon, Ofri

2011-01-01

that describes the architectural exclusivity of this particular architecture genre. The adjective green expresses architectural qualities differentiating green architecture from none-green architecture. Currently, adding trees and vegetation to the building’s facade is the main architectural characteristics...... they have overshadowed the architectural potential of green architecture. The paper questions how a green space should perform, look like and function. Two examples are chosen to demonstrate thorough integrations between green and space. The examples are public buildings categorized as pavilions. One......The paper investigates the topic of green architecture from an architectural point of view and not an energy point of view. The purpose of the paper is to establish a debate about the architectural language and spatial characteristics of green architecture. In this light, green becomes an adjective...

The Influence of Proactive Green Innovation and Reactive Green Innovation on Green Product Development Performance: The Mediation Role of Green Creativity

Directory of Open Access Journals (Sweden)

Yu-Shan Chen

2016-09-01

Full Text Available This study fills the research gap in the exploration of the relationships between both proactive and reactive green innovations and green product development performance, and examines the mediating effect of green creativity. Structural equation modeling (SEM is utilized to test the hypotheses. From the sample of 146 valid respondents, the results show that proactive green innovation positively affects green creativity and green product development performance, and green creativity positively affects green product development performance. In addition, our findings also indicate that the relationship between proactive green innovation and green product development performance is partially mediated by green creativity. Accordingly, green creativity plays a critical role for companies to achieve a great green product development performance. However, reactive green innovation does not significantly influence green creativity and green product development performance. Companies should develop proactive green innovation rather than reactive green innovation in order to enhance their green creativity and increase their product development performance.

Can urban tree roots improve infiltration through compacted subsoils for stormwater management?

Science.gov (United States)

Bartens, Julia; Day, Susan D; Harris, J Roger; Dove, Joseph E; Wynn, Theresa M

2008-01-01

Global land use patterns and increasing pressures on water resources demand creative urban stormwater management. Strategies encouraging infiltration can enhance groundwater recharge and water quality. Urban subsoils are often relatively impermeable, and the construction of many stormwater detention best management practices (D-BMPs) exacerbates this condition. Root paths can act as conduits for water, but this function has not been demonstrated for stormwater BMPs where standing water and dense subsoils create a unique environment. We examined whether tree roots can penetrate compacted subsoils and increase infiltration rates in the context of a novel infiltration BMP (I-BMP). Black oak (Quercus velutina Lam.) and red maple (Acer rubrum L.) trees, and an unplanted control, were installed in cylindrical planting sleeves surrounded by clay loam soil at two compaction levels (bulk density = 1.3 or 1.6 g cm(-3)) in irrigated containers. Roots of both species penetrated the more compacted soil, increasing infiltration rates by an average of 153%. Similarly, green ash (Fraxinus pennsylvanica Marsh.) trees were grown in CUSoil (Amereq Corp., New York) separated from compacted clay loam subsoil (1.6 g cm(-3)) by a geotextile. A drain hole at mid depth in the CUSoil layer mimicked the overflow drain in a stormwater I-BMP thus allowing water to pool above the subsoil. Roots penetrated the geotextile and subsoil and increased average infiltration rate 27-fold compared to unplanted controls. Although high water tables may limit tree rooting depth, some species may be effective tools for increasing water infiltration and enhancing groundwater recharge in this and other I-BMPs (e.g., raingardens and bioswales).

Improving Resilience to Emergencies through Advanced Cyber Technologies: the I-REACT project

Directory of Open Access Journals (Sweden)

Claudia Maltoni

2017-08-01

be equipped with essential tools for early warning and response. At the same time, private companies could leverage specific set of I-REACT components to improve their business, when linked to disaster management. Overall, I-REACT aims to be a European-wide contribution to build more secure and resilient societies to disasters.

MECHANICS OF DYNAMIC POWDER COMPACTION PROCESS

OpenAIRE

Nurettin YAVUZ

1996-01-01

In recent years, interest in dynamic compaction methods of metal powders has increased due to the need to improve compaction properties and to increase production rates of compacts. In this paper, review of dynamic and explosive compaction of metal powders are given. An attempt is made to get a better understanding of the compaction process with the mechanicis of powder compaction.

High-luminosity blue and blue-green gallium nitride light-emitting diodes.

Science.gov (United States)

Morkoç, H; Mohammad, S N

1995-01-06

Compact and efficient sources of blue light for full color display applications and lighting eluded and tantalized researchers for many years. Semiconductor light sources are attractive owing to their reliability and amenability to mass manufacture. However, large band gaps are required to achieve blue color. A class of compound semiconductors formed by metal nitrides, GaN and its allied compounds AIGaN and InGaN, exhibits properties well suited for not only blue and blue-green emitters, but also for ultraviolet emitters and detectors. What thwarted engineers and scientists from fabricating useful devices from these materials in the past was the poor quality of material and lack of p-type doping. Both of these obstacles have recently been overcome to the point where highluminosity blue and blue-green light-emitting diodes are now available in the marketplace.

KEEFEKTIFAN STRATEGI REACT DITINJAU DARI PRESTASI BELAJAR, KEMAMPUAN PENYELESAIAN MASALAH, KONEKSI MATEMATIS, SELF EFFICACY

Directory of Open Access Journals (Sweden)

Runtyani Irjayanti Putri

2015-11-01

Full Text Available Penelitian ini bertujuan untuk: (1 mendeskripsikan keefektifan strategi pembelajaran REACT pada pembelajaran turunan fungsi ditinjau dari prestasi belajar matematika, kemampuan penyelesaian masalah matematis, kemampuan koneksi matematis, dan Self efficacy siswa SMA Negeri 4 Magelang, (2 menentukan strategi pembelajaran yang lebih efektif diantara strategi REACT dan pembelajaran konvensional pada pembelajaran turunan fungsi ditinjau dari aspek prestasi belajar matematika, kemampuan penyelesaian masalah matematis, kemampuan koneksi matematis, dan Self efficacy siswa SMA Negeri 4 Magelang. Penelitian ini adalah penelitian quasi experiment. Teknik pengumpulan data yang digunakan adalah teknik tes dan nontes. Teknik analisis data yang digunakan adalah uji one sample t-test, uji T2 Hotelling’s, dan uji t-Bonferroni. Hasil penelitian menunjukkan bahwa: (1 strategi pembelajaran REACT efektif pada pembelajaran turunan fungsi ditinjau dari prestasi belajar matematika, kemampuan penyelesaian masalah matematis, kemampuan koneksi matematis, dan Self efficacy siswa SMA Negeri 4 Magelang, dan (2 strategi pembelajaran REACT lebih efektif daripada pembelajaran konvensional pada pembelajaran turunan fungsi ditinjau dari aspek prestasi belajar matematika, kemampuan penyelesaian masalah matematis, kemampuan koneksi matematis, dan Self efficacy siswa SMA Negeri 4 Magelang. Kata Kunci: strategi REACT, prestasi belajar, kemampuan penyelesaian masalah matematis, kemampuan koneksi matematis, dan Self efficacy siswa SMA   THE EFFECTIVENESS OF REACT STRATEGY VIEWED FROM LEARNING ACHIEVEMENT, PROBLEM SOLVING ABILITY, MATHEMATICAL CONNECTION, SELF EFFICACY Abstract The aims of this study are to: (1 to describe the effectiveness of the REACT strategy viewed from Mathematics Learning Achievement, Mathematics Problem Solving Ability, Mathematics Connection Ability, and Student Self efficacy of State Senior High School 4 Magelang Students, and (2 determine a more effective

Pengaruh Green Marketing Hotel Terhadap Green Consumer Behavior

OpenAIRE

Yo Fernandez, Eunike Christe; Tjoanda, Evelyn

2017-01-01

Penelitian ini dilakukan untuk mengetahui pengaruh dari green marketing hotel terhadap green consumer behavior. Green marketing memiliki 3 dimensi, yaitu green product, green price, dan green promotion. Penelitian ini melibatkan 272 responden masyarakat Surabaya dan menggunakan metode regresi linear berganda. Hasil penelitian menunjukkan bahwa green product dan green price berpengaruh secara positif dan signifikan sedangkan green promotion berpengaruh namun tidak signifikan terhadap green con...

Effect of primary particle size on spray formation, morphology and internal structure of alumina granules and elucidation of flowability and compaction behaviour

Directory of Open Access Journals (Sweden)

Pandu Ramavath

2014-06-01

Full Text Available Three different alumina powders with varying particle sizes were subjected to spray drying under identical conditions and effect of particle size on heat transfer efficiency and mechanism of formation of granules was elucidated. Morphology, internal structure and size distribution of granules were studied and evaluated with respect to their flow behaviour. In order to estimate the elastic interaction of granules, the granules were subjected to compaction under progressive loading followed by periodic unloading. Compaction curves were plotted and compressibility factor was estimated and correlated with predicted and measured green density values.

GREEN PEA GALAXIES REVEAL SECRETS OF Lyα ESCAPE

Energy Technology Data Exchange (ETDEWEB)

Yang, Huan; Wang, Junxian [CAS Key Laboratory for Research in Galaxies and Cosmology, Department of Astronomy, University of Science and Technology of China (China); Malhotra, Sangeeta; Rhoads, James E. [Arizona State University, School of Earth and Space Exploration (United States); Gronke, Max; Dijkstra, Mark [Institute of Theoretical Astrophysics, University of Oslo (Norway); Jaskot, Anne [Smith College, Northampton, MA (United States); Zheng, Zhenya, E-mail: yanghuan@mail.ustc.edu.cn, E-mail: huan.y@asu.edu, E-mail: Sangeeta.Malhotra@asu.edu, E-mail: James.Rhoads@asu.edu [Pontificia Universidad Católica de Chile, Santiago (Chile)

2016-04-01

We analyze archival Lyα spectra of 12 “Green Pea” galaxies observed with the Hubble Space Telescope, model their Lyα profiles with radiative transfer models, and explore the dependence of the Lyα escape fraction on various properties. Green Pea galaxies are nearby compact starburst galaxies with [O iii] λ5007 equivalent widths (EWs) of hundreds of Å. All 12 Green Pea galaxies in our sample show Lyα lines in emission, with an Lyα EW distribution similar to high-redshift Lyα emitters. Combining the optical and UV spectra of Green Pea galaxies, we estimate their Lyα escape fractions and find correlations between Lyα escape fraction and kinematic features of Lyα profiles. The escape fraction of Lyα in these galaxies ranges from 1.4% to 67%. We also find that the Lyα escape fraction depends strongly on metallicity and moderately on dust extinction. We compare their high-quality Lyα profiles with single H i shell radiative transfer models and find that the Lyα escape fraction anticorrelates with the derived H i column densities. Single-shell models fit most Lyα profiles well, but not the ones with the highest escape fractions of Lyα. Our results suggest that low H i column density and low metallicity are essential for Lyα escape and make a galaxy an Lyα emitter.

VizieR Online Data Catalog: Compact steep spectrum new sample (Kunert-Bajraszewska+, 2010)

Science.gov (United States)

Kunert-Bajraszewska, M.; Gawronski, M. P.; Labiano, A.; Siemiginowska, A.

2013-08-01

Using the final release of FIRST, combined with the Green Bank 6-cm (GB6) survey at 4.85GHz, we looked for unresolved, isolated sources, that is, more compact than the FIRST beam (5.4-arcsec), and surrounded by an empty field (we adopted 1-arcmin as the radius of that field). We required that the redshifts of the objects identified with radio sources were known, and we extracted these from the National Aeronautics and Space Administration (NASA)/Infrared Processing and Analysis Center (IPAC) Extragalactic Data base (NED) and the Sloan Digital Sky Survey (SDSS). (3 data files).

Process to separate alkali metal salts from alkali metal reacted hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Gordon, John Howard; Alvare, Javier; Larsen, Dennis; Killpack, Jeff

2017-06-27

A process to facilitate gravimetric separation of alkali metal salts, such as alkali metal sulfides and polysulfides, from alkali metal reacted hydrocarbons. The disclosed process is part of a method of upgrading a hydrocarbon feedstock by removing heteroatoms and/or one or more heavy metals from the hydrocarbon feedstock composition. This method reacts the oil feedstock with an alkali metal and an upgradant hydrocarbon. The alkali metal reacts with a portion of the heteroatoms and/or one or more heavy metals to form an inorganic phase containing alkali metal salts and reduced heavy metals, and an upgraded hydrocarbon feedstock. The inorganic phase may be gravimetrically separated from the upgraded hydrocarbon feedstock after mixing at a temperature between about 350.degree. C. to 400.degree. C. for a time period between about 15 minutes and 2 hours.

Compact and high repetition rate Kerr-lens mode-locked 532 nm Nd:YVO4 laser

International Nuclear Information System (INIS)

Li, Zuohan; Peng, Jiying; Yuan, Ruixia; Yao, Jianquan; Zheng, Yi; Wang, Tongtong

2015-01-01

A compact and feasible CW Kerr-lens-induced mode-locked 532 nm Nd:YVO 4 laser system was experimentally demonstrated for the first time with theoretical analysis. Kerr-lens mode locking with intracavity second harmonic generation provides a promising method to generate a high-repetition-rate picosecond green laser. With an incident pump power of 6 W, the average output power of mode locking was 258 mW at a high repetition rate of 1.1 GHz. (paper)

Clastic compaction unit classification based on clay content and integrated compaction recovery using well and seismic data

Directory of Open Access Journals (Sweden)

Zhong Hong

2016-11-01

Full Text Available Abstract Compaction correction is a key part of paleo-geomorphic recovery methods. Yet, the influence of lithology on the porosity evolution is not usually taken into account. Present methods merely classify the lithologies as sandstone and mudstone to undertake separate porosity-depth compaction modeling. However, using just two lithologies is an oversimplification that cannot represent the compaction history. In such schemes, the precision of the compaction recovery is inadequate. To improve the precision of compaction recovery, a depth compaction model has been proposed that involves both porosity and clay content. A clastic lithological compaction unit classification method, based on clay content, has been designed to identify lithological boundaries and establish sets of compaction units. Also, on the basis of the clastic compaction unit classification, two methods of compaction recovery that integrate well and seismic data are employed to extrapolate well-based compaction information outward along seismic lines and recover the paleo-topography of the clastic strata in the region. The examples presented here show that a better understanding of paleo-geomorphology can be gained by applying the proposed compaction recovery technology.

A generalised Green-Julg theorem for proper groupoids and Banach algebras

OpenAIRE

Paravicini, Walther

2009-01-01

The Green-Julg theorem states that K_0^G(B) is isomorphic to K_0(L^1(G,B)) for every compact group G and every G-C*-algebra B. We formulate a generalisation of this result to proper groupoids and Banach algebras and deduce that the Bost assembly map is surjective for proper Banach algebras. On the way, we show that the spectral radius of an element in a C_0(X)-Banach algebra can be calculated from the spectral radius in the fibres.

Complex-shaped ceramic composites obtained by machining compact polymer-filler mixtures

Directory of Open Access Journals (Sweden)

Rosa Maria da Rocha

2005-06-01

Full Text Available Research in the preparation of ceramics from polymeric precursors is giving rise to increased interest in ceramic technology because it allows the use of several promising polymer forming techniques. In this work ceramic composite pieces were obtained by pyrolysis of a compacted mixture of a polysiloxane resin and alumina/silicon powder. The mixture consists of 60 vol% of the polymer phase and 40 vol% of the filler in a 1:1 ratio for alumina/silicon, which was hot pressed to crosslink the polymer, thus forming a compact body. This green body was trimmed into different geometries and pyrolised in nitrogen atmosphere at temperatures up to 1600 °C. X-ray diffraction analysis indicated the formation of phases such as mullite and Si2ON2 during pyrolysis, that result from reactions between fillers, polymer decomposition products and nitrogen atmosphere. The porosity was found to be less than 20% and the mass loss around 10%. The complex geometry was maintained after pyrolysis and shrinkage was approximately 8%, proving pyrolisis to be a suitable process to form near-net-shaped bulk ceramic components.

Prediction of reacting atoms for the major biotransformation reactions of organic xenobiotics.

Science.gov (United States)

Rudik, Anastasia V; Dmitriev, Alexander V; Lagunin, Alexey A; Filimonov, Dmitry A; Poroikov, Vladimir V

2016-01-01

The knowledge of drug metabolite structures is essential at the early stage of drug discovery to understand the potential liabilities and risks connected with biotransformation. The determination of the site of a molecule at which a particular metabolic reaction occurs could be used as a starting point for metabolite identification. The prediction of the site of metabolism does not always correspond to the particular atom that is modified by the enzyme but rather is often associated with a group of atoms. To overcome this problem, we propose to operate with the term "reacting atom", corresponding to a single atom in the substrate that is modified during the biotransformation reaction. The prediction of the reacting atom(s) in a molecule for the major classes of biotransformation reactions is necessary to generate drug metabolites. Substrates of the major human cytochromes P450 and UDP-glucuronosyltransferases from the Biovia Metabolite database were divided into nine groups according to their reaction classes, which are aliphatic and aromatic hydroxylation, N- and O-glucuronidation, N-, S- and C-oxidation, and N- and O-dealkylation. Each training set consists of positive and negative examples of structures with one labelled atom. In the positive examples, the labelled atom is the reacting atom of a particular reaction that changed adjacency. Negative examples represent non-reacting atoms of a particular reaction. We used Labelled Multilevel Neighbourhoods of Atoms descriptors for the designation of reacting atoms. A Bayesian-like algorithm was applied to estimate the structure-activity relationships. The average invariant accuracy of prediction obtained in leave-one-out and 20-fold cross-validation procedures for five human isoforms of cytochrome P450 and all isoforms of UDP-glucuronosyltransferase varies from 0.86 to 0.99 (0.96 on average). We report that reacting atoms may be predicted with reasonable accuracy for the major classes of metabolic reactions

Numerical simulation of reacting and non-reacting flow in a combustion chamber; Numerisk simulering av reagerande och icke-reagerande stroemning i en braennkammare

Energy Technology Data Exchange (ETDEWEB)

Borg, A.; Revstedt, J.

1996-04-01

The purpose of this work has been to do a preliminary study of how well numerical calculations with different turbulence models can predict the flow and temperature fields of a strongly swirling and combusting flow in an experimental combustion chamber and to see which parameters in the mathematical model are the most important. The combustion chamber on which we have done the calculations is called Validation Rig II and was designed by Volvo Aero Corporation. The main part of the study has been carried out on a non-reacting flow but some work has also been done on reacting flow. In most cases it has not been meaningful to compare the calculations with the measurements because they differ quite a lot from each other. For the non-reacting case the following investigations have been made: * How the solution differs for different turbulence models, * The solutions sensitivity to inlet boundary conditions, * How different types of leakage disturb the flow, and * The difference in results between two different CFD-codes, the commercial code CFDS-Flow3D and a code developed at the department of fluid mechanics. For the reacting cases we have studied the influence of: * one or two reaction steps, * the effects of a change in reaction rate, * the influence of thermal radiation, and * the effects of changing the boundary conditions for temperature on the walls. The results from these calculations show that the inlet turbulence intensity has very little effect on the values of the turbulent quantities as well as the velocity profiles at the outlet. Changing the turbulence model or the outlet boundary conditions gives some change in velocity profiles at the outlet but only marginal effects on the swirl number. 21 refs, 54 figs, 19 tabs

Development task of compact reactor

International Nuclear Information System (INIS)

Kurushima, Morihiro

1982-01-01

In the Ministry of International Trade and Industry, studies proceed on the usage of compact medium and small LWRs. As such, the reactors from 100 to 200 MW may meet varieties of demands in scale and kind in view of the saving of petroleum and the economy of nuclear power. In this case, the technology of light water reactors with already established safety will be suitable for the development of compact reactors. The concept of ''nuclear power community'' using the compact reactors in local society and industrial zones was investigated. The following matters are described: need for the introduction of compact reactors, the survey on the compact reactor systems, and the present status and future problems for compact reactor usage. (J.P.N.)

Spectrophotometric determination of boron by solvent extraction with 2-hydroxy-2-methylbutyric acid and malachite green

Energy Technology Data Exchange (ETDEWEB)

Sato, Shigeya; Uchikawa, Sumio [Kumamoto Univ. (Japan). Faculty of Education

1984-03-01

A very simple and sensitive method for the spectrophotometric determination of boron was developed. Boron was found to react with 2-hydroxy-2-methylbutyric acid in weak acidic aqueous solution at room temperature to form a complex anion which can be extracted into chlorobenzene with malachite green in a single extraction; boron is determined indirectly by measuring the absorbance of malachite green in the extract at 629 nm. The calibration graph is linear over the range (7.50 x 10/sup -7/ - 2.00 x 10/sup -5/) mol dm/sup -3/ boron; the apparent molar absorptivity is 6.50 x 10/sup 4/ dm/sup 3/ mol/sup -1/ cm/sup -1/. The method is applied to the determination of micro amounts of boron in natural waters with satisfactory results.

Green(ing) infrastructure

CSIR Research Space (South Africa)

Van Wyk, Llewellyn V

2014-03-01

Full Text Available the generation of electricity from renewable sources such as wind, water and solar. Grey infrastructure – In the context of storm water management, grey infrastructure can be thought of as the hard, engineered systems to capture and convey runoff..., pumps, and treatment plants.  Green infrastructure reduces energy demand by reducing the need to collect and transport storm water to a suitable discharge location. In addition, green infrastructure such as green roofs, street trees and increased...

The complete chloroplast genome sequence of the chlorophycean green alga Scenedesmus obliquus reveals a compact gene organization and a biased distribution of genes on the two DNA strands

Science.gov (United States)

de Cambiaire, Jean-Charles; Otis, Christian; Lemieux, Claude; Turmel, Monique

2006-01-01

Background The phylum Chlorophyta contains the majority of the green algae and is divided into four classes. While the basal position of the Prasinophyceae is well established, the divergence order of the Ulvophyceae, Trebouxiophyceae and Chlorophyceae (UTC) remains uncertain. The five complete chloroplast DNA (cpDNA) sequences currently available for representatives of these classes display considerable variability in overall structure, gene content, gene density, intron content and gene order. Among these genomes, that of the chlorophycean green alga Chlamydomonas reinhardtii has retained the least ancestral features. The two single-copy regions, which are separated from one another by the large inverted repeat (IR), have similar sizes, rather than unequal sizes, and differ radically in both gene contents and gene organizations relative to the single-copy regions of prasinophyte and ulvophyte cpDNAs. To gain insights into the various changes that underwent the chloroplast genome during the evolution of chlorophycean green algae, we have sequenced the cpDNA of Scenedesmus obliquus, a member of a distinct chlorophycean lineage. Results The 161,452 bp IR-containing genome of Scenedesmus features single-copy regions of similar sizes, encodes 96 genes, i.e. only two additional genes (infA and rpl12) relative to its Chlamydomonas homologue and contains seven group I and two group II introns. It is clearly more compact than the four UTC algal cpDNAs that have been examined so far, displays the lowest proportion of short repeats among these algae and shows a stronger bias in clustering of genes on the same DNA strand compared to Chlamydomonas cpDNA. Like the latter genome, Scenedesmus cpDNA displays only a few ancestral gene clusters. The two chlorophycean genomes share 11 gene clusters that are not found in previously sequenced trebouxiophyte and ulvophyte cpDNAs as well as a few genes that have an unusual structure; however, their single-copy regions differ

The algorithms for calculating synthetic seismograms from a dipole source using the derivatives of Green's function

Science.gov (United States)

Pavlov, V. M.

2017-07-01

The problem of calculating complete synthetic seismograms from a point dipole with an arbitrary seismic moment tensor in a plane parallel medium composed of homogeneous elastic isotropic layers is considered. It is established that the solutions of the system of ordinary differential equations for the motion-stress vector have a reciprocity property, which allows obtaining a compact formula for the derivative of the motion vector with respect to the source depth. The reciprocity theorem for Green's functions with respect to the interchange of the source and receiver is obtained for a medium with cylindrical boundary. The differentiation of Green's functions with respect to the coordinates of the source leads to the same calculation formulas as the algorithm developed in the previous work (Pavlov, 2013). A new algorithm appears when the derivatives with respect to the horizontal coordinates of the source is replaced by the derivatives with respect to the horizontal coordinates of the receiver (with the minus sign). This algorithm is more transparent, compact, and economic than the previous one. It requires calculating the wavenumbers associated with Bessel function's roots of order 0 and order 1, whereas the previous algorithm additionally requires the second order roots.

Degradation of malachite green in aqueous solution by Fenton process.

Science.gov (United States)

Hameed, B H; Lee, T W

2009-05-30

In this study, advanced oxidation process utilizing Fenton's reagent was investigated for degradation of malachite green (MG). The effects of different reaction parameters such as the initial MG concentration, initial pH, the initial hydrogen peroxide concentration, the initial ferrous concentration and the reaction temperature on the oxidative degradation of MG have been investigated. The optimal reacting conditions were experimentally found to be pH 3.40, initial hydrogen peroxide concentration=0.50mM and initial ferrous concentration=0.10mM for initial MG concentration of 20mg/L at 30 degrees C. Under optimal conditions, 99.25% degradation efficiency of dye in aqueous solution was achieved after 60 min of reaction.

Compaction dynamics of crunchy granular material

Directory of Open Access Journals (Sweden)

Guillard François

2017-01-01

Full Text Available Compaction of brittle porous material leads to a wide variety of densification patterns. Static compaction bands occurs naturally in rocks or bones, and have important consequences in industry for the manufacturing of powder tablets or metallic foams for example. Recently, oscillatory compaction bands have been observed in brittle porous media like snow or cereals. We will discuss the great variety of densification patterns arising during the compaction of puffed rice, including erratic compaction at low velocity, one or several travelling compaction bands at medium velocity and homogeneous compaction at larger velocity. The conditions of existence of each pattern are studied thanks to a numerical spring lattice model undergoing breakage and is mapped to the phase diagram of the patterns based on dimensionless characteristic quantities. This also allows to rationalise the evolution of the compaction behaviour during a single test. Finally, the localisation of compaction bands is linked to the strain rate sensitivity of the material.

Compaction dynamics of crunchy granular material

Science.gov (United States)

Guillard, François; Golshan, Pouya; Shen, Luming; Valdès, Julio R.; Einav, Itai

2017-06-01

Compaction of brittle porous material leads to a wide variety of densification patterns. Static compaction bands occurs naturally in rocks or bones, and have important consequences in industry for the manufacturing of powder tablets or metallic foams for example. Recently, oscillatory compaction bands have been observed in brittle porous media like snow or cereals. We will discuss the great variety of densification patterns arising during the compaction of puffed rice, including erratic compaction at low velocity, one or several travelling compaction bands at medium velocity and homogeneous compaction at larger velocity. The conditions of existence of each pattern are studied thanks to a numerical spring lattice model undergoing breakage and is mapped to the phase diagram of the patterns based on dimensionless characteristic quantities. This also allows to rationalise the evolution of the compaction behaviour during a single test. Finally, the localisation of compaction bands is linked to the strain rate sensitivity of the material.

Summary of Self-compacting Concrete Workability

OpenAIRE

GUO Gui-xiang; Duan Hong-jun

2015-01-01

On the basis of a large number of domestic and foreign literature, situation and development of self-compacting concrete is introduced. Summary of the compacting theory of self-compacting concrete. And some of the factors affecting the workability of self-compacting concrete were discussed and summarized to a certain extent. Aims to further promote the application and research of self-compacting concrete

Model Compaction Equation

African Journals Online (AJOL)

The currently proposed model compaction equation was derived from data sourced from the. Niger Delta and it relates porosity to depth for sandstones under hydrostatic pressure condition. The equation is useful in predicting porosity and compaction trend in hydrostatic sands of the. Niger Delta. GEOLOGICAL SETTING OF ...

Summable chains of instantons: Green's functions and the Prasad-Sommerfield limit

International Nuclear Information System (INIS)

Boutaleb-Joutei, H.; Chakrabarti, A.; Comtet, A.

1981-01-01

We construct, for each homotopy class, a type of instanton configuration which exhibits many special, simple properties. The basic reason behind such properties is indicated by deriving our configuration in the 't Hooft gauge, starting from a class of particularly simple, static, and self-dual solutions in de Sitter space. Apart from this we consider, in this paper, mostly results for flat Euclidean space. We show that the static solutions are equivalent to multiply charged instantons at the origin in Witten's sense. Green's functions for this class of instanton background are studied. The known flat-space results of Brown et al. are shown to be reducible, for our case, to totally explicit and relatively compact forms. The sums over different indices arising in their formalism are performed. The inversion of a matrix, necessary for the isospin-1 massless scalar field, is carried out explicitly, for our configuration, for arbitrary index of the background instanton field. Green's functions for the Prasad-Sommerfield case are obtained as limits of our results directly in summed-up forms. Green's functions are studied also in de Sitter space. Special features due to periodic time are pointed out

Computation of turbulent reacting flow in a solid-propellant ducted rocket

Science.gov (United States)

Chao, Yei-Chin; Chou, Wen-Fuh; Liu, Sheng-Shyang

1995-05-01

A mathematical model for computation of turbulent reacting flows is developed under general curvilinear coordinate systems. An adaptive, streamline grid system is generated to deal with the complex flow structures in a multiple-inlet solid-propellant ducted rocket (SDR) combustor. General tensor representations of the k-epsilon and algebraic stress (ASM) turbulence models are derived in terms of contravariant velocity components, and modification caused by the effects of compressible turbulence is also included in the modeling. The clipped Gaussian probability density function is incorporated in the combustion model to account for fluctuations of properties. Validation of the above modeling is first examined by studying mixing and reacting characteristics in a confined coaxial-jet problem. This is followed by study of nonreacting and reacting SDR combustor flows. The results show that Gibson and Launder's ASM incorporated with Sarkar's modification for compressible turbulence effects based on the general curvilinear coordinate systems yields the most satisfactory prediction for this complicated SDR flowfield.

Nb3Sn dipole magnet reacted after winding

International Nuclear Information System (INIS)

Taylor, C.; Scanlan, R.; Peters, C.; Wolgast, R.; Gilbert, W.; Hassenzahl, W.; Meuser, R.; Rechen, J.

1984-09-01

A 5 cm bore dia., 1-m-long dipole model magnet was constructed by winding un-reacted cable, followed by reaction and epoxy-impregnation. Experience and test results are described on the 1.7 mm dia. internal-tin wire, the eleven-strand flattened cable, fiberglass insulation, and construction of the magnet. Each half of the magnet has two double-pancake-type windings that were reacted in a single operation. The two double-pancakes were then separately vacuum impregnated after soldering the flexible Nb-Ti leads to the Nb 3 Sn conductors. No iron flux return yoke was used. In initial tests a central field of 8.0 T was reached at 4.4 K. However, evidence from training behavior, and 1.8 K tests indicate that premature quenching, rather than critical current of the cable, limited the field intensity. The magnet was reassembled and more rigidly clamped; additional test results are reported

Pharmaceutical powder compaction technology

National Research Council Canada - National Science Library

Çelik, Metin

2011-01-01

... through the compaction formulation process and application. Compaction of powder constituents both active ingredient and excipients is examined to ensure consistent and reproducible disintegration and dispersion profiles...

Methane for Power Generation in Muaro Jambi: A Green Prosperity Model Project

Energy Technology Data Exchange (ETDEWEB)

Moriarty, K.; Elchinger, M.; Hill, G.; Katz, J.; Barnett, J.

2014-07-01

NREL conducted eight model projects for Millennium Challenge Corporation's (MCC) Compact with Indonesia. Green Prosperity, the largest project of the Compact, seeks to address critical constraints to economic growth while supporting the Government of Indonesia's commitment to a more sustainable, less carbon-intensive future. This study evaluates electricity generation from the organic content of wastewater at a palm oil mill in Muaro Jambi, Sumatra. Palm mills use vast amounts of water in the production process resulting in problematic waste water called palm oil mill effluent (POME). The POME releases methane to the atmosphere in open ponds which could be covered to capture the methane to produce renewable electricity for rural villages. The study uses average Indonesia data to determine the economic viability of methane capture at a palm oil mill and also evaluates technology as well as social and environmental impacts of the project.

Blue-Green Solutions in Urban Development

Science.gov (United States)

Karlsson, Caroline; Kalantari, Zahra

2017-04-01

With the ongoing urbanisation and increasing pressure for new housing and infrastructure, the nexus of developing compact, energy-efficient and yet liveable and sustainable cities is urgent to address. In this context, blue-green spaces and related ecosystem services (ES) are critical resources that need to be integrated in policy and planning of urban. Among the ES provided by blue-green spaces, regulating ES such as water retention and purification are particularly important in urban areas, affecting water supply and quality, related cultural ES and biodiversity, as well as cities potential to adapt to climate change. Blue-green infrastructure management is considered a sustainable way to reducing negative effects of urbanisation, such as decreasing flood risks, as well as adapting to climate change for example by controlling increasing flood and drought risks. Blue-green infrastructure management can for example create multifunctional surfaces with valuable environmental and social functions and generally handle greenways and ecological networks as important ecosystem service components, for example for stormwater regulation in a sustainable urban drainage system. The Norrström drainage basin (22,000 km2) is a large demonstrator for Blue-green infrastructure management. Both urbanisation and agriculture are extensive within this basin, which includes the Swedish capital Stockholm and is part of the fertile Swedish belt. Together, the relatively high population density combined with agricultural and industrial activities in this region imply large eutrophication and pollution pressures, not least transferred through storm runoff to both inland surface waters and the coastal waters of the Baltic Sea. The ecosystems of this basin provide highly valued but also threatened services. For example, Lake Mälaren is the single main freshwater supply for the Swedish capital Stockholm, as well as a key nutrient retention system that strongly mitigates waterborne nutrient

Customers’ Intention to Use Green Products: the Impact of Green Brand Dimensions and Green Perceived Value

Directory of Open Access Journals (Sweden)

Doszhanov Aibek

2015-01-01

Full Text Available This study aimed to identify the relationships between green brand dimension (green brand awareness, green brand image, and green brand trust, green perceived value and customer’s intention to use green products. Data was collected through structured survey questionnaire from 384 customers of three hypermarkets in Kuala-Lumpur. Data was analyzed based on multiple regression analysis. The results indicate that there are significant relationships between green brand awareness, green brand trust, green perceived value, and customer’s intention to use green products. However, green brand image was not found to have significant relationship with customer’s intention to use green products. The discussion presented suggestions for marketers and researchers interested in green branding.

Ultrasonic and mechanical behavior of green and partially sintered alumina: Effects of slurry consolidation chemistry

Energy Technology Data Exchange (ETDEWEB)

Schilling, C.H.; Garcia, V.J.; Smith, R.M. [Ames Lab., IA (United States)]|[Iowa State Univ., Ames, IA (United States). Dept. of Materials Science and Engineering; Roberts, R.A. [Iowa State Univ., Ames, IA (United States)

1998-10-01

Green and partially sintered compacts of {alpha}-Al{sub 2}O{sub 3} powder were made by filtration of aqueous suspensions under three conditions: (i) electrostatic stabilization without any organic additive, (ii) strong flocculation near the isoelectric point without any organic additive, and (iii) weak flocculation by the use of maltodextrin or oxalic acid additives. The authors evaluated relationships between the macroscopic and interparticle mechanical behavior of these compacts using model correlations with measurements of diametral compression, ultrasonic velocity, and ultrasonic attenuation. Although type iii green specimens were less dense than type i, type iii exhibited significant increases in velocity, macroscopic Young`s modulus, interparticle-contact stiffness, and diametral compressive strength, suggesting that the mechanism of stiffening/strengthening entailed interparticle bridging of maltodextrin or oxalic acid. These properties were significantly reduced upon heating type iii specimens to 500 C, suggesting that pyrolysis of surface-adsorbed maltodextrin and oxalic acid may have reduced the interparticle stiffness and strength. In contrast, negligible changes in these properties occurred upon heating type i specimens to the same temperature. Despite small increases in packing density, significant decreases in attenuation and significant increases in velocity, interparticle-contact stiffness, and Young`s modulus occurred upon heating all specimens to {ge}700 C, suggesting the formation of interparticle necks by solid-state sintering.

Step-by-Step Simulation of Radiation Chemistry Using Green Functions for Diffusion-Influenced Reactions

Science.gov (United States)

Plante, Ianik; Cucinotta, Francis A.

2011-01-01

Radiolytic species are formed approximately 1 ps after the passage of ionizing radiation through matter. After their formation, they diffuse and chemically react with other radiolytic species and neighboring biological molecules, leading to various oxidative damage. Therefore, the simulation of radiation chemistry is of considerable importance to understand how radiolytic species damage biological molecules [1]. The step-by-step simulation of chemical reactions is difficult, because the radiolytic species are distributed non-homogeneously in the medium. Consequently, computational approaches based on Green functions for diffusion-influenced reactions should be used [2]. Recently, Green functions for more complex type of reactions have been published [3-4]. We have developed exact random variate generators of these Green functions [5], which will allow us to use them in radiation chemistry codes. Moreover, simulating chemistry using the Green functions is which is computationally very demanding, because the probabilities of reactions between each pair of particles should be evaluated at each timestep [2]. This kind of problem is well adapted for General Purpose Graphic Processing Units (GPGPU), which can handle a large number of similar calculations simultaneously. These new developments will allow us to include more complex reactions in chemistry codes, and to improve the calculation time. This code should be of importance to link radiation track structure simulations and DNA damage models.

Weakly compact operators and interpolation

OpenAIRE

Maligranda, Lech

1992-01-01

The class of weakly compact operators is, as well as the class of compact operators, a fundamental operator ideal. They were investigated strongly in the last twenty years. In this survey, we have collected and ordered some of this (partly very new) knowledge. We have also included some comments, remarks and examples. The class of weakly compact operators is, as well as the class of compact operators, a fundamental operator ideal. They were investigated strongly in the last twenty years. I...

The Influence of Proactive Green Innovation and Reactive Green Innovation on Green Product Development Performance: The Mediation Role of Green Creativity

OpenAIRE

Yu-Shan Chen; Tai-Wei Chang; Chun-Yu Lin; Pi-Yu Lai; Kuan-Hung Wang

2016-01-01

This study fills the research gap in the exploration of the relationships between both proactive and reactive green innovations and green product development performance, and examines the mediating effect of green creativity. Structural equation modeling (SEM) is utilized to test the hypotheses. From the sample of 146 valid respondents, the results show that proactive green innovation positively affects green creativity and green product development performance, and green creativity positivel...

REAC/TS radiation accident registry. Update of accidents in the United States

International Nuclear Information System (INIS)

Ricks, R.C.; Berger, M.E.; Holloway, E.C.; Goans, R.E.

2000-01-01

Serious injury due to ionizing radiation is a rare occurrence. From 1944 to the present, 243 US accidents meeting dose criteria for classification as serious are documented in the REAC/TS Registry. Thirty individuals have lost their lives in radiation accidents in the United States. The Registry is part of the overall REAC/TS program providing 24-hour direct or consultative assistance regarding medical and heath physics problems associated with radiation accidents in local, national, and international incidents. The REAC/TS Registry serves as a repository of medically important information documenting the consequences of these accidents. Registry data are gathered from various sources. These include reports from the World Heath Organization (WHO), International Atomic Energy Agency (IAEA), US Nuclear Regulatory Commission (US NRC), state radiological health departments, medical/health physics literature, personal communication, the Internet, and most frequently, from calls for medical assistance to REAC/TS, as part of our 24-hour medical assistance program. The REAC/TS Registry for documentation of radiation accidents serves several useful purposes: 1) weaknesses in design, safety practices, training or control can be identified, and trends noted; 2) information regarding the medical consequences of injuries and the efficacy of treatment protocols is available to the treating physician; and 3) Registry case studies serve as valuable teaching tools. This presentation will review and summarize data on the US radiation accidents including their classification by device, accident circumstances, and frequency by respective states. Data regarding accidents with fatal outcomes will be reviewed. The inclusion of Registry data in the IAEA's International Reporting System of Radiation Events (RADEV) will also be discussed. (author)

3.5 W of diffraction-limited green light at 515 nm from SHG of a single-frequency tapered diode laser

DEFF Research Database (Denmark)

Jensen, Ole Bjarlin; Hansen, Anders Kragh; Müller, André

2017-01-01

Multi-Watt efficient compact green laser sources are required for a number of applications e.g. within biophotonics, laser pumping and laser displays. We present generation of 3.5 W of diffraction-limited green light at 515 nm by second harmonic generation (SHG) of a tapered diode laser, itself...... yielding more than 9 W at 1030 nm. SHG is performed in single pass through a cascade of two nonlinear crystals with re-focusing and dispersion compensating optics between the two nonlinear crystals. The laser is single-frequency and the output power is stabilized to better than ±0.4%....

Compact hematite buffer layer as a promoter of nanorod photoanode performances

Science.gov (United States)

Milan, R.; Cattarin, S.; Comisso, N.; Baratto, C.; Kaunisto, K.; Tkachenko, N. V.; Concina, I.

2016-10-01

The effect of a thin α-Fe2O3 compact buffer layer (BL) on the photoelectrochemical performances of a bare α-Fe2O3 nanorods photoanode is investigated. The BL is prepared through a simple spray deposition onto a fluorine-doped tin oxide (FTO) conducting glass substrate before the growth of a α-Fe2O3 nanorods via a hydrothermal process. Insertion of the hematite BL between the FTO and the nanorods markedly enhances the generated photocurrent, by limiting undesired losses of photogenerated charges at the FTO||electrolyte interface. The proposed approach warrants a marked improvement of material performances, with no additional thermal treatment and no use/dispersion of rare or toxic species, in agreement with the principles of green chemistry.

The Entropy of Co-Compact Open Covers

Directory of Open Access Journals (Sweden)

Steven Bourquin

2013-06-01

Full Text Available Co-compact entropy is introduced as an invariant of topological conjugation for perfect mappings defined on any Hausdorff space (compactness and metrizability are not necessarily required. This is achieved through the consideration of co-compact covers of the space. The advantages of co-compact entropy include: (1 it does not require the space to be compact and, thus, generalizes Adler, Konheim and McAndrew’s topological entropy of continuous mappings on compact dynamical systems; and (2 it is an invariant of topological conjugation, compared to Bowen’s entropy, which is metric-dependent. Other properties of co-compact entropy are investigated, e.g., the co-compact entropy of a subsystem does not exceed that of the whole system. For the linear system, (R; f, defined by f(x = 2x, the co-compact entropy is zero, while Bowen’s entropy for this system is at least log 2. More generally, it is found that co-compact entropy is a lower bound of Bowen’s entropies, and the proof of this result also generates the Lebesgue Covering Theorem to co-compact open covers of non-compact metric spaces.

Metaphysical green

DEFF Research Database (Denmark)

Earon, Ofri

2011-01-01

to adapt to urban environment. It explores the potential of Sensation of Green in the city. The paper questions whether the Sensation of Green could introduce a new spectrum of greens, beside the real green. It develops the term of metaphysical green – does green have to be green or can it be only...

A stochastic model of particle dispersion in turbulent reacting gaseous environments

Science.gov (United States)

Sun, Guangyuan; Lignell, David; Hewson, John

2012-11-01

We are performing fundamental studies of dispersive transport and time-temperature histories of Lagrangian particles in turbulent reacting flows. The particle-flow statistics including the full particle temperature PDF are of interest. A challenge in modeling particle motions is the accurate prediction of fine-scale aerosol-fluid interactions. A computationally affordable stochastic modeling approach, one-dimensional turbulence (ODT), is a proven method that captures the full range of length and time scales, and provides detailed statistics of fine-scale turbulent-particle mixing and transport. Limited results of particle transport in ODT have been reported in non-reacting flow. Here, we extend ODT to particle transport in reacting flow. The results of particle transport in three flow configurations are presented: channel flow, homogeneous isotropic turbulence, and jet flames. We investigate the functional dependence of the statistics of particle-flow interactions including (1) parametric study with varying temperatures, Reynolds numbers, and particle Stokes numbers; (2) particle temperature histories and PDFs; (3) time scale and the sensitivity of initial and boundary conditions. Flow statistics are compared to both experimental measurements and DNS data.

EAF Slag Aggregate in Roller-Compacted Concrete Pavement: Effects of Delay in Compaction

Directory of Open Access Journals (Sweden)

My Ngoc-Tra Lam

2018-04-01

Full Text Available This study investigates the effect of delay in compaction on the optimum moisture content and the mechanical propertie s (i.e., compressive strength, ultrasonic pulse velocity, splitting tensile strength, and modulus of elasticity of roller-compacted concrete pavement (RCCP made of electric arc furnace (EAF slag aggregate. EAF slag with size in the range of 4.75–19 mm was used to replace natural coarse aggregate in RCCP mixtures. A new mixing method was proposed for RCCP using EAF slag aggregate. The optimum moisture content of RCCP mixtures in this study was determined by a soil compaction method. The Proctor test assessed the optimum moisture content of mixtures at various time after mixing completion (i.e., 0, 15, 30, 60, and 90 min. Then, the effect of delay in compaction on the mechanical properties of RCCP mixtures at 28 days of age containing EAF slag aggregate was studied. The results presented that the negative effect on water content in the mixture caused by the higher water absorption characteristic of EAF slag was mitigated by the new mixing method. The optimum water content and maximum dry density of RCCP experience almost no effect from the delay in compaction. The compressive strength and splitting tensile strength of RCCP using EAF slag aggregate fulfilled the strength requirements for pavement with 90 min of delay in compaction.

Can Culture Act as an Enabler to Innovation? Exploring the Germany-Ontario Experience Regarding the Introduction of Green Energy

OpenAIRE

Bill Irwin; Jan A.C. Klakurka

2015-01-01

This paper explores the role that societal culture may play in terms of acting as an inhibitor or enabler when creating conditions conducive to innovative enterprise. To further understanding of this concept, the paper's authors explore different cultural influences and traditions of the country of Germany and the Canadian province of Ontario against the backdrop of the introduction of a government green energy policy and how local business reacts to new opportunities forthcoming from this sh...

Keefektifan Strategi Pembelajaran React Pada Kemampuan Siswa Kelas VII Aspek Komunikasi Matematis

Directory of Open Access Journals (Sweden)

A.T. Arifin

2014-06-01

Full Text Available AbstrakTujuan penelitian ini adalah mengetahui pembelajaran dengan strategi REACT efektif ter-hadap kemampuan komunikasi matematis siswa. Metode pengumpulan data dilakukan de-ngan metode dokumentasi, tes, dan observasi. Hasil uji proporsi menunjukkan bahwa hasil belajar siswa kelas eksperimen pada aspek kemampuan komunikasi matematis telah men-capai ketuntasan klasikal, mencapai lebih dari 80 % yaitu sebesar 96,7%. Dilihat dari nilai rata-rata tes kemampuan komunikasi matematis kelas eksperimen  adalah 83,61 sedangkan kelas kontrol adalah 73,79 dapat disimpulkan bahwa kemampuan komunikasi matematis siswa kelas eksperimen lebih baik daripada kemampuan komunikasi matematis siswa kon-trol. Hasil penelitian menunjukkan bahwa penerapan strategi pembelajaran REACT efektif terhadap kemampuan komunikasi matematis siswa materi segiempat kelas VII SMP Negeri 1 Gembong. Kata kunci:      keefektifan, kemampuan komunikasi matematis, Relating Experiencing Applying Cooperating Transferring (REACT  AbstractThe purpose of this study was to determine the effectiveness of the application of REACT learning strategy approach to mathematic communication ability of students. Methods of data collection is done by the method of documentation, testing, and observation. The test results showed that the proportion of student learning outcomes in the experimental class with the aspects of mathematic communication ability has reached the classical completeness, reached more than 80% is equal to 96.7%. Judging from the value of the average test learners' ability to mathematic communication experimental class was 83.61 while the control class is 73.79 it can be concluded that the mathematic communication skills of learners experimental classes are better than mathematic communication abilities of learners control class. The results showed that the application of REACT learning strategy approach effective to mathematic communication abilities of students of class VII

The Rapid Formation of Localized Compaction Bands Under Hydrostatic Load Leading to Pore-pressure Transients in Compacting Rocks

Science.gov (United States)

Faulkner, D.; Leclere, H.; Bedford, J. D.; Behnsen, J.; Wheeler, J.

2017-12-01

Compaction of porous rocks can occur uniformly or within localized deformation bands. The formation of compaction bands and their effects on deformation behaviour are poorly understood. Porosity may be primary and compaction can occur with burial, or it can be produced by metamorphic reactions with a solid volume reduction, that can then undergo collapse. We report results from hydrostatic compaction experiments on porous bassanite (CaSO4.0.5H2O) aggregates. Gypsum (CaSO4.2H2O) is first dehydrated under low effective pressure, 4 MPa, to produce a bassanite aggregate with a porosity of 27%. Compaction is induced by increasing confining pressure at rates from 0.001 MPa/s to 0.02 MPa/s while the sample is maintained at a temperature of 115°C. At slow compaction rates, porosity collapse proceeds smoothly. At higher compaction rates, sudden increases in the pore-fluid pressure occur with a magnitude of 5 MPa. Microstructural investigations using X-ray microtomography and SEM observations show that randomly oriented localized compaction features occur in all samples, where the bulk porosity of 18% outside the band is reduced to 5% inside the band. Previous work on deformation bands has suggested that localized compactive features only form under an elevated differential stress and not under a hydrostatic stress state. The magnitude of the pore-pressure pulses can be explained by the formation of compaction bands. The results indicate that the compaction bands can form by rapid (unstable) propagation across the sample above a critical strain rate, or quasi-statically at low compaction rates without pore-fluid pressure bursts. The absence of pore-fluid pressure bursts at slow compaction rates can be explained by viscous deformation of the bassanite aggregate around the tip of a propagating compaction band, relaxing stress, and promoting stable propagation. Conversely, at higher compaction rates, viscous deformation cannot relax the stress sufficiently and unstable

Diverse Formation Mechanisms for Compact Galaxies

Science.gov (United States)

Kim, Jin-Ah; Paudel, Sanjaya; Yoon, Suk-Jin

2018-01-01

Compact, quenched galaxies such as M32 are unusual ones located off the mass - size scaling relation defined by normal galaxies. Still, their formation mechanisms remain unsolved. Here we investigate the evolution of ~100 compact, quenched galaxies at z = 0 identified in the Illustris cosmological simulation. We identify three ways for a galaxy to become a compact one and, often, multiple mechanisms operate in a combined manner. First, stripping is responsible for making about a third of compact galaxies. Stripping removes stars from galaxies, usually while keeping their sizes intact. About one third are galaxies that cease their growth early on after entering into more massive, gigantic halos. Finally, about half of compact galaxies, ~ 35 % of which turn out to undergo stripping, experience the compaction due to the highly centrally concentrated star formation. We discuss the evolutionary path of compact galaxies on the mass – size plane for each mechanism in a broader context of dwarf galaxy formation and evolution.

Simultaneous Temperature and Velocity Diagnostic for Reacting Flows, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A diagnostic technique is proposed for measuring temperature and velocity simultaneously in a high temperature reacting flow for aiding research in propulsion. The...

Compact Process Development at Babcock & Wilcox

Energy Technology Data Exchange (ETDEWEB)

Eric Shaber; Jeffrey Phillips

2012-03-01

Multiple process approaches have been used historically to manufacture cylindrical nuclear fuel compacts. Scale-up of fuel compacting was required for the Next Generation Nuclear Plant (NGNP) project to achieve an economically viable automated production process capable of providing a minimum of 10 compacts/minute with high production yields. In addition, the scale-up effort was required to achieve matrix density equivalent to baseline historical production processes, and allow compacting at fuel packing fractions up to 46% by volume. The scale-up approach of jet milling, fluid-bed overcoating, and hot-press compacting adopted in the U.S. Advanced Gas Reactor (AGR) Fuel Development Program involves significant paradigm shifts to capitalize on distinct advantages in simplicity, yield, and elimination of mixed waste. A series of compaction trials have been completed to optimize compaction conditions of time, temperature, and forming pressure using natural uranium oxycarbide (NUCO) fuel at packing fractions exceeding 46% by volume. Results from these trials are included. The scale-up effort is nearing completion with the process installed and operable using nuclear fuel materials. Final process testing is in progress to certify the process for manufacture of qualification test fuel compacts in 2012.

The Influence of Environmental Friendliness on Green Trust: The Mediation Effects of Green Satisfaction and Green Perceived Quality

Directory of Open Access Journals (Sweden)

Yu-Shan Chen

2015-07-01

Full Text Available As global green trends became more prevalent, green marketing also developed into an important issue. Although prior literature explored the main factors affecting green trust, it was inconclusive as to how environmental friendliness could affect the green trust in green marketing. This study aims to focus on the positive influence of environmental friendliness on green trust, and explore the mediation effects of green satisfaction and green perceived quality. This study undertakes an empirical study by means of questionnaire survey. The respondents are consumers who have experience purchasing green products. This study applies structural equation modeling (SEM to test the hypotheses. The findings of this study indicate that (1 environmental friendliness has a significant positive impact on green satisfaction, green perceived quality, and green trust; (2 both green satisfaction and green perceived quality positively affect green trust; and (3 green satisfaction and green perceived quality partially mediate the positive relationship between environmental friendliness and green trust.

Compact magnetic confinement fusion: Spherical torus and compact torus

Directory of Open Access Journals (Sweden)

Zhe Gao

2016-05-01

Full Text Available The spherical torus (ST and compact torus (CT are two kinds of alternative magnetic confinement fusion concepts with compact geometry. The ST is actually a sub-category of tokamak with a low aspect ratio; while the CT is a toroidal magnetic configuration with a simply-connected geometry including spheromak and field reversed pinch. The ST and CT have potential advantages for ultimate fusion reactor; while at present they can also provide unique fusion science and technology contributions for mainstream fusion research. However, some critical scientific and technology issues should be extensively investigated.

Compact stars

Science.gov (United States)

Estevez-Delgado, Gabino; Estevez-Delgado, Joaquin

2018-05-01

An analysis and construction is presented for a stellar model characterized by two parameters (w, n) associated with the compactness ratio and anisotropy, respectively. The reliability range for the parameter w ≤ 1.97981225149 corresponds with a compactness ratio u ≤ 0.2644959374, the density and pressures are positive, regular and monotonic decrescent functions, the radial and tangential speed of sound are lower than the light speed, moreover, than the plausible stability. The behavior of the speeds of sound are determinate for the anisotropy parameter n, admitting a subinterval where the speeds are monotonic crescent functions and other where we have monotonic decrescent functions for the same speeds, both cases describing a compact object that is also potentially stable. In the bigger value for the observational mass M = 2.05 M⊙ and radii R = 12.957 Km for the star PSR J0348+0432, the model indicates that the maximum central density ρc = 1.283820319 × 1018 Kg/m3 corresponds to the maximum value of the anisotropy parameter and the radial and tangential speed of the sound are monotonic decrescent functions.

Developing Dynamic Single Page Web Applications Using Meteor : Comparing JavaScript Frameworks: Blaze and React

OpenAIRE

Yetayeh, Asabeneh

2017-01-01

This paper studies Meteor which is a JavaScript full-stack framework to develop interactive single page web applications. Meteor allows building web applications entirely in JavaScript. Meteor uses Blaze, React or AngularJS as a view layer and Node.js and MongoDB as a back-end. The main purpose of this study is to compare the performance of Blaze and React. A multi-user Blaze and React web applications with similar HTML and CSS were developed. Both applications were deployed on Heroku’s w...

Roller-compacted concrete pavements.

Science.gov (United States)

2010-09-01

Roller-compacted concrete (RCC) gets its name from the heavy vibratory steel drum and rubber-tired rollers used to help compact it into its final form. RCC has similar strength properties and consists of the same basic ingredients as conventional con...

A model for reaction rates in turbulent reacting flows

Science.gov (United States)

Chinitz, W.; Evans, J. S.

1984-01-01

To account for the turbulent temperature and species-concentration fluctuations, a model is presented on the effects of chemical reaction rates in computer analyses of turbulent reacting flows. The model results in two parameters which multiply the terms in the reaction-rate equations. For these two parameters, graphs are presented as functions of the mean values and intensity of the turbulent fluctuations of the temperature and species concentrations. These graphs will facilitate incorporation of the model into existing computer programs which describe turbulent reacting flows. When the model was used in a two-dimensional parabolic-flow computer code to predict the behavior of an experimental, supersonic hydrogen jet burning in air, some improvement in agreement with the experimental data was obtained in the far field in the region near the jet centerline. Recommendations are included for further improvement of the model and for additional comparisons with experimental data.

Green power certification: environmental and consumer protection benefits of the Green-e programme

Energy Technology Data Exchange (ETDEWEB)

Wingate, M.; Hamrin, J. [Center for Resource Solutions (United States); Rabago, K. [Rocky Mountain Inst. (United States); Wiser, R. [Lawrence Berkeley National Lab. (United States)

2000-06-01

This article gives details of the Green-e environmental certification programme which certifies electricity generated from renewable energy sources in the US. This first non-profit certification programme originally was set up for California, and has now spread to other regions. The objectives of the Green-e programme, the need for the electricity product to meet minimum criteria to qualify, marketer requirements, verification of product claims, administration of the programme, and the second year programme results are discussed. The way in which the Green-e programme fits in with other programmes such as those set up by the state and federal customer protection agencies to help consumers select environmentally superior power is described.

The Lω-Compactness in Lω-Spaces

Directory of Open Access Journals (Sweden)

Shui-Li Chen

2013-01-01

Full Text Available The concepts of αω-remote neighborhood family, γω-cover, and Lω-compactness are defined in Lω-spaces. The characterizations of Lω-compactness are systematically discussed. Some important properties of Lω-compactness such as ω-closed heredity, arbitrarily multiplicative property, and preserving invariance under ω-continuous mappings are obtained. Finally, the Alexander ω-subbase lemma and the Tychonoff product theorem with respect to Lω-compactness are given.

UV written compact broadband optical couplers

DEFF Research Database (Denmark)

Olivero, Massimo; Svalgaard, Mikael

2005-01-01

In this paper the first demonstration of compact asymmetric directional couplers made by UV writing is presented. The combined performance in terms bandwidth, loss and compactness exceeds that reported using other, more elaborate fabrication techniques.......In this paper the first demonstration of compact asymmetric directional couplers made by UV writing is presented. The combined performance in terms bandwidth, loss and compactness exceeds that reported using other, more elaborate fabrication techniques....

Autoshaping with common and distinctive stimulus elements, compact and dispersed arrays.

Science.gov (United States)

Sperling, S E; Perkins, M E

1979-05-01

Four groups of pigeons were trained with a standard autoshaping procedure in which a brief fixed-duration interval always followed by a grain delivery alternated with a longer variable-duration interval never associated with grain delivery. One of two stimuli was always presented during each interval. One of them contained three black dots and a black star on a green background; the other contained four black dots on a green background. The four elements of each stimulus were arranged in a more compact array for two groups and in a more dispersed array for the other two groups. Which of the two stimuli preceded grain delivery was counterbalanced within each pair of groups. The speed of occurrence of the first autoshaped peck was not affected by whether the stimulus containing the distinctive star element preceded grain delivery, but autoshaping was faster when the stimulus arrays were compact than when they were dispersed. During 560 response-independent training trials that followed the first autoshaped peck, this pattern reversed; both discriminative control over responding and the relative frequency of pecking the stimulus that preceded grain delivery were greater for the two groups where this stimulus contained the discriminative element than for the two groups where it contained only common elements. During subsequent testing with stimuli containing only a single element each, the distinctive feature was responded to proportionately more often by the two groups for which it had been an element of the stimulus preceding grain delivery than by the two groups for which it had been an element of the stimulus complex that never was associated with grain delivery. These data add further support to the hypothesis that the initial occurrence of autoshaped responding and its subsequent maintenance are not affected by the same variables. They also suggest that automaintenance is as sensitive as response-dependent training to the presence or absence of a distinctive

Prediction of reservoir compaction and surface subsidence

Energy Technology Data Exchange (ETDEWEB)

De Waal, J.A.; Smits, R.M.M.

1988-06-01

A new loading-rate-dependent compaction model for unconsolidated clastic reservoirs is presented that considerably improves the accuracy of predicting reservoir rock compaction and surface subsidence resulting from pressure depletion in oil and gas fields. The model has been developed on the basis of extensive laboratory studies and can be derived from a theory relating compaction to time-dependent intergranular friction. The procedure for calculating reservoir compaction from laboratory measurements with the new model is outlined. Both field and laboratory compaction behaviors appear to be described by one single normalized, nonlinear compaction curve. With the new model, the large discrepancies usually observed between predictions based on linear compaction models and actual (nonlinear) field behavior can be explained.

The green building envelope : Vertical greening

NARCIS (Netherlands)

Ottelé, M.

2011-01-01

Planting on roofs and façades is one of the most innovative and fastest developing fields of green technologies with respect to the built environment and horticulture. This thesis is focused on vertical greening of structures and to the multi-scale benefits of vegetation. Vertical green can improve

Different event-related patterns of gamma-band power in brain waves of fast- and slow-reacting subjects.

Science.gov (United States)

Jokeit, H; Makeig, S

1994-01-01

Fast- and slow-reacting subjects exhibit different patterns of gamma-band electroencephalogram (EEG) activity when responding as quickly as possible to auditory stimuli. This result appears to confirm long-standing speculations of Wundt that fast- and slow-reacting subjects produce speeded reactions in different ways and demonstrates that analysis of event-related changes in the amplitude of EEG activity recorded from the human scalp can reveal information about event-related brain processes unavailable using event-related potential measures. Time-varying spectral power in a selected (35- to 43-Hz) gamma frequency band was averaged across trials in two experimental conditions: passive listening and speeded reacting to binaural clicks, forming 40-Hz event-related spectral responses. Factor analysis of between-subject event-related spectral response differences split subjects into two near-equal groups composed of faster- and slower-reacting subjects. In faster-reacting subjects, 40-Hz power peaked near 200 ms and 400 ms poststimulus in the react condition, whereas in slower-reacting subjects, 40-Hz power just before stimulus delivery was larger in the react condition. These group differences were preserved in separate averages of relatively long and short reaction-time epochs for each group. gamma-band (20-60 Hz)-filtered event-related potential response averages did not differ between the two groups or conditions. Because of this and because gamma-band power in the auditory event-related potential is small compared with the EEG, the observed event-related spectral response features must represent gamma-band EEG activity reliably induced by, but not phase-locked to, experimental stimuli or events. PMID:8022783

Compaction properties of isomalt

NARCIS (Netherlands)

Bolhuis, Gerad K.; Engelhart, Jeffrey J. P.; Eissens, Anko C.

Although other polyols have been described extensively as filler-binders in direct compaction of tablets, the polyol isomalt is rather unknown as pharmaceutical excipient, in spite of its description in all the main pharmacopoeias. In this paper the compaction properties of different types of

GREEN MANAGEMENT: THE REALITY OF BEING GREEN IN BUSINESS

OpenAIRE

Tran, Ben

2009-01-01

Green management and going green are not as clear cut and easy as hyped by the general media. While going ecologically green is indeed beneficial and appropriate, the process and procedure of becoming green is anything but easy. Firstly, turning green is largely not a legal requirement, but a voluntary process. Thus, even though LEED (which is by far the more publicly known green certification standard) governs the certification of the green management effort, it is not a compulsory condition...

Study of subgrid-scale velocity models for reacting and nonreacting flows

Science.gov (United States)

Langella, I.; Doan, N. A. K.; Swaminathan, N.; Pope, S. B.

2018-05-01

A study is conducted to identify advantages and limitations of existing large-eddy simulation (LES) closures for the subgrid-scale (SGS) kinetic energy using a database of direct numerical simulations (DNS). The analysis is conducted for both reacting and nonreacting flows, different turbulence conditions, and various filter sizes. A model, based on dissipation and diffusion of momentum (LD-D model), is proposed in this paper based on the observed behavior of four existing models. Our model shows the best overall agreements with DNS statistics. Two main investigations are conducted for both reacting and nonreacting flows: (i) an investigation on the robustness of the model constants, showing that commonly used constants lead to a severe underestimation of the SGS kinetic energy and enlightening their dependence on Reynolds number and filter size; and (ii) an investigation on the statistical behavior of the SGS closures, which suggests that the dissipation of momentum is the key parameter to be considered in such closures and that dilatation effect is important and must be captured correctly in reacting flows. Additional properties of SGS kinetic energy modeling are identified and discussed.

Phased array compaction cell for measurement of the transversely isotropic elastic properties of compacting sediments

Energy Technology Data Exchange (ETDEWEB)

Nihei, K.T.; Nakagawa, S.; Reverdy, F.; Meyer, L.R.; Duranti, L.; Ball, G.

2010-12-15

Sediments undergoing compaction typically exhibit transversely isotropic (TI) elastic properties. We present a new experimental apparatus, the phased array compaction cell, for measuring the TI elastic properties of clay-rich sediments during compaction. This apparatus uses matched sets of P- and S-wave ultrasonic transducers located along the sides of the sample and an ultrasonic P-wave phased array source, together with a miniature P-wave receiver on the top and bottom ends of the sample. The phased array measurements are used to form plane P-waves that provide estimates of the phase velocities over a range of angles. From these measurements, the five TI elastic constants can be recovered as the sediment is compacted, without the need for sample unloading, recoring, or reorienting. This paper provides descriptions of the apparatus, the data processing, and an application demonstrating recovery of the evolving TI properties of a compacting marine sediment sample.

Development of Implicit Compact Methods for Chemically Reacting Flows

Science.gov (United States)

2009-02-28

NSP_P), DKt (NSP_P), & ! stoichiometric coeffs (# mols produced/destroyed) & NUK(NSP_P), & ! mass coeffs: NUK(k)*WK(k) & NUKWK(NSP_P), & & WK... DKt UC UCr wc WCz NUK NUKWK ! (nu_0 sstoich Yfuel Yox Yfuel_F Yox_A Z PHI omega SOURCE q HEAT = SpecificHeat(T) = 0 .do...RHO*T) dot_product(DK,YKr) ! correction vel. for mass conservation dot_product(DK,YKrr)+dot_product(( DKt *Tr),YKr) dot_product(DK,YKz) ! correction

Large-scale dynamic compaction of natural salt

International Nuclear Information System (INIS)

Hansen, F.D.; Ahrens, E.H.

1996-01-01

A large-scale dynamic compaction demonstration of natural salt was successfully completed. About 40 m 3 of salt were compacted in three, 2-m lifts by dropping a 9,000-kg weight from a height of 15 m in a systematic pattern to achieve desired compaction energy. To enhance compaction, 1 wt% water was added to the relatively dry mine-run salt. The average compacted mass fractional density was 0.90 of natural intact salt, and in situ nitrogen permeabilities averaged 9X10 -14 m 2 . This established viability of dynamic compacting for placing salt shaft seal components. The demonstration also provided compacted salt parameters needed for shaft seal system design and performance assessments of the Waste Isolation Pilot Plant

Effects of Fusion Tack Welds on Self-Reacting Friction Stir Welds

Science.gov (United States)

Nunes, A. C., Jr.; Pendleton, M. L.; Brooke, S. A.; Russell, C. K.

2012-01-01

In order to know whether fusion tack welds would affect the strength of self-reacting friction stir seam welds in 2195-T87 aluminum alloy, the fracture stresses of 144 tensile test coupons cut from 24 welded panels containing segments of friction stir welds were measured. Each of the panels was welded under unique processing conditions. A measure of the effect of the tack welds for each panel was devised. An analysis of the measures of the tack weld effect supported the hypothesis that fusion tack welds do not affect the strength of self-reacting friction stir welds to a 5% level of confidence.

Direct numerical simulations of reacting flows with detailed chemistry using many-core/GPU acceleration

KAUST Repository

Herná ndez Pé rez, Francisco E.; Mukhadiyev, Nurzhan; Xu, Xiao; Sow, Aliou; Lee, Bok Jik; Sankaran, Ramanan; Im, Hong G.

2018-01-01

A new direct numerical simulation (DNS) code for multi-component gaseous reacting flows has been developed at KAUST, with the state-of-the-art programming model for next generation high performance computing platforms. The code, named KAUST Adaptive Reacting Flows Solver (KARFS), employs the MPI+X programming, and relies on Kokkos for “X” for performance portability to multi-core, many-core and GPUs, providing innovative software development while maintaining backward compatibility with established parallel models and legacy code. The capability and potential of KARFS to perform DNS of reacting flows with large, detailed reaction mechanisms is demonstrated with various model problems involving ignition and turbulent flame propagations with varying degrees of chemical complexities.

Direct numerical simulations of reacting flows with detailed chemistry using many-core/GPU acceleration

KAUST Repository

Hernández Pérez, Francisco E.

2018-03-29

A new direct numerical simulation (DNS) code for multi-component gaseous reacting flows has been developed at KAUST, with the state-of-the-art programming model for next generation high performance computing platforms. The code, named KAUST Adaptive Reacting Flows Solver (KARFS), employs the MPI+X programming, and relies on Kokkos for “X” for performance portability to multi-core, many-core and GPUs, providing innovative software development while maintaining backward compatibility with established parallel models and legacy code. The capability and potential of KARFS to perform DNS of reacting flows with large, detailed reaction mechanisms is demonstrated with various model problems involving ignition and turbulent flame propagations with varying degrees of chemical complexities.

Source analysis using regional empirical Green's functions: The 2008 Wells, Nevada, earthquake

Science.gov (United States)

Mendoza, C.; Hartzell, S.

2009-01-01

We invert three-component, regional broadband waveforms recorded for the 21 February 2008 Wells, Nevada, earthquake using a finite-fault methodology that prescribes subfault responses using eight MW∼4 aftershocks as empirical Green's functions (EGFs) distributed within a 20-km by 21.6-km fault area. The inversion identifies a seismic moment of 6.2 x 1024 dyne-cm (5.8 MW) with slip concentrated in a compact 6.5-km by 4-km region updip from the hypocenter. The peak slip within this localized area is 88 cm and the stress drop is 72 bars, which is higher than expected for Basin and Range normal faults in the western United States. The EGF approach yields excellent fits to the complex regional waveforms, accounting for strong variations in wave propagation and site effects. This suggests that the procedure is useful for studying moderate-size earthquakes with limited teleseismic or strong-motion data and for examining uncertainties in slip models obtained using theoretical Green's functions.

Advances in compact manufacturing for shape and performance controllability of large-scale components-a review

Science.gov (United States)

Qin, Fangcheng; Li, Yongtang; Qi, Huiping; Ju, Li

2017-01-01

Research on compact manufacturing technology for shape and performance controllability of metallic components can realize the simplification and high-reliability of manufacturing process on the premise of satisfying the requirement of macro/micro-structure. It is not only the key paths in improving performance, saving material and energy, and green manufacturing of components used in major equipments, but also the challenging subjects in frontiers of advanced plastic forming. To provide a novel horizon for the manufacturing in the critical components is significant. Focused on the high-performance large-scale components such as bearing rings, flanges, railway wheels, thick-walled pipes, etc, the conventional processes and their developing situations are summarized. The existing problems including multi-pass heating, wasting material and energy, high cost and high-emission are discussed, and the present study unable to meet the manufacturing in high-quality components is also pointed out. Thus, the new techniques related to casting-rolling compound precise forming of rings, compact manufacturing for duplex-metal composite rings, compact manufacturing for railway wheels, and casting-extruding continuous forming of thick-walled pipes are introduced in detail, respectively. The corresponding research contents, such as casting ring blank, hot ring rolling, near solid-state pressure forming, hot extruding, are elaborated. Some findings in through-thickness microstructure evolution and mechanical properties are also presented. The components produced by the new techniques are mainly characterized by fine and homogeneous grains. Moreover, the possible directions for further development of those techniques are suggested. Finally, the key scientific problems are first proposed. All of these results and conclusions have reference value and guiding significance for the integrated control of shape and performance in advanced compact manufacturing.

Sustainable green urban planning: the Green Credit Tool

NARCIS (Netherlands)

Cilliers, E.J.; Diemont, E.; Stobbelaar, D.J.; Timmermans, W.

2010-01-01

Purpose – The Green Credit Tool is evaluated as a method to quantify the value of green-spaces and to determine how these green-space-values can be replaced or compensated for within urban spatial planning projects. Design/methodology/approach – Amersfoort Local Municipality created the Green Credit

Fungal Microbiomes Associated with Green and Non-Green Building Materials.

Science.gov (United States)

Coombs, Kanistha; Vesper, Stephen; Green, Brett J; Yermakov, Mikhail; Reponen, Tiina

2017-01-01

Water-damaged buildings can lead to fungal growth and occupant health problems. Green building materials, derived from renewable sources, are increasingly utilized in construction and renovations. However, the question as to what fungi will grow on these green compared to non-green materials, after they get wet, has not been adequately studied. By determining what fungi grow on each type of material, the potential health risks can be more adequately assessed. In this study, we inoculated green and non-green pieces of ceiling tile, composite board, drywall, and flooring with indoor dust containing a complex mixture of naturally occurring fungi. The materials were saturated with water and incubated for two months in a controlled environment. The resulting fungal microbiomes were evaluated using ITS amplicon sequencing. Overall, the richness and diversity of the mycobiomes on each pair of green and non-green pieces were not significantly different. However, different genera dominated on each type of material. For example, Aspergillus spp. had the highest relative abundance on green and non-green ceiling tiles and green composite boards, but Peniophora spp. dominated the non-green composite board. In contrast, Penicillium spp. dominated green and non-green flooring samples. Green gypsum board was dominated by Phialophora spp. and Stachybotrys spp., but non-green gypsum board by Myrothecium spp. These data suggest that water-damaged green and non-green building materials can result in mycobiomes that are dominated by fungal genera whose member species pose different potentials for health risks.

Birefringence characteristics in sperm heads allow for the selection of reacted spermatozoa for intracytoplasmic sperm injection.

Science.gov (United States)

Gianaroli, Luca; Magli, M Cristina; Ferraretti, Anna P; Crippa, Andor; Lappi, Michela; Capitani, Serena; Baccetti, Baccio

2010-02-01

To verify clinical outcome after injection of spermatozoa that have undergone the acrosome reaction (reacted spermatozoa) vs. those still having an intact acrosome (nonreacted spermatozoa). Prospective, randomized study. Reproductive Medicine Unit, Italian Society for the Study of Reproductive Medicine, Bologna, Italy. According to a prospective randomization including 71 couples with severe male factor infertility, intracytoplasmic sperm injection (ICSI) was performed under polarized light that permitted analysis of the pattern of birefringence in the sperm head. Twenty-three patients had their oocytes injected with reacted spermatozoa, 26 patient's oocytes were injected with nonreacted spermatozoa, and in 22 patients both reacted and nonreacted spermatozoa were injected. Intracytoplasmic sperm injection was performed under polarized light to selectively inject acrosome-reacted and acrosome-nonreacted spermatozoa. Rates of fertilization, cleavage, pregnancy, implantation, and ongoing implantation. There was no effect on the fertilizing capacity and embryo development of either type of sperm, whereas the implantation rate was higher in oocytes injected with reacted spermatozoa (39.0%) vs. those injected with nonreacted spermatozoa (8.6%). The implantation rate was 24.4% in the group injected with both reacted and nonreacted spermatozoa. The delivery rate per cycle followed the same trend. Spermatozoa that have undergone the acrosome reaction seem to be more prone to supporting the development of viable ICSI embryos. Copyright 2010 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Soil compaction and growth of woody plants

Energy Technology Data Exchange (ETDEWEB)

Kozlowski, T.T. [Univ. of California, Berkeley (United States). Dept. of Environmental Science, Policy and Management

1999-07-01

Although soil compaction in the field may benefit or inhibit the growth of plants, the harmful effects are much more common. This paper emphasizes the deleterious effects of predominantly high levels of soil compaction on plant growth and yield. High levels of soil compaction are common in heavily used recreation areas, construction sites, urban areas, timber harvesting sites, fruit orchards, agroforestry systems and tree nurseries. Compaction can occur naturally by settling or slumping of soil or may be induced by tillage tools, heavy machinery, pedestrian traffic, trampling by animals and fire. Compaction typically alters soil structure and hydrology by increasing soil bulk density; breaking down soil aggregates; decreasing soil porosity, aeration and infiltration capacity; and by increasing soil strength, water runoff and soil erosion. Appreciable compaction of soil leads to physiological dysfunctions in plants. Often, but not always, reduced water absorption and leaf water deficits develop. Soil compaction also induces changes in the amounts and balances of growth hormones in plants, especially increases in abscisic acid and ethylene. Absorption of the major mineral nutrients is reduced by compaction of both surface soils and subsoils. The rate of photosynthesis of plants growing in very compacted soil is decreased by both stomatal and non-stomatal inhibition. Total photosynthesis is reduced as a result of smaller leaf areas. As soils become increasingly compacted respiration of roots shifts toward an anaerobic state. Severe soil compaction adversely influences regeneration of forest stands by inhibiting seed germination and growth of seedlings, and by inducing seedling mortality. Growth of woody plants beyond the seedling stage and yields of harvestable plant products also are greatly decreased by soil compaction because of the combined effects of high soil strength, decreased infiltration of water and poor soil aeration, all of which lead to a decreased

Soil compaction and growth of woody plants

International Nuclear Information System (INIS)

Kozlowski, T.T.

1999-01-01

Although soil compaction in the field may benefit or inhibit the growth of plants, the harmful effects are much more common. This paper emphasizes the deleterious effects of predominantly high levels of soil compaction on plant growth and yield. High levels of soil compaction are common in heavily used recreation areas, construction sites, urban areas, timber harvesting sites, fruit orchards, agroforestry systems and tree nurseries. Compaction can occur naturally by settling or slumping of soil or may be induced by tillage tools, heavy machinery, pedestrian traffic, trampling by animals and fire. Compaction typically alters soil structure and hydrology by increasing soil bulk density; breaking down soil aggregates; decreasing soil porosity, aeration and infiltration capacity; and by increasing soil strength, water runoff and soil erosion. Appreciable compaction of soil leads to physiological dysfunctions in plants. Often, but not always, reduced water absorption and leaf water deficits develop. Soil compaction also induces changes in the amounts and balances of growth hormones in plants, especially increases in abscisic acid and ethylene. Absorption of the major mineral nutrients is reduced by compaction of both surface soils and subsoils. The rate of photosynthesis of plants growing in very compacted soil is decreased by both stomatal and non-stomatal inhibition. Total photosynthesis is reduced as a result of smaller leaf areas. As soils become increasingly compacted respiration of roots shifts toward an anaerobic state. Severe soil compaction adversely influences regeneration of forest stands by inhibiting seed germination and growth of seedlings, and by inducing seedling mortality. Growth of woody plants beyond the seedling stage and yields of harvestable plant products also are greatly decreased by soil compaction because of the combined effects of high soil strength, decreased infiltration of water and poor soil aeration, all of which lead to a decreased

Second law analysis of a reacting temperature dependent viscous ...

African Journals Online (AJOL)

In this paper, entropy generation during the flow of a reacting viscous fluid through an inclined Channel with isothermal walls are investigated. The coupled energy and momentum equations were solved numerically. Previous results in literature (Adesanya et al 2006 [[17]) showed both velocity and temperature have two ...

Small Valdivia compact spaces

CERN Document Server

Kubi's, W; Kubi\\'s, Wieslaw; Michalewski, Henryk

2005-01-01

We prove a preservation theorem for the class of Valdivia compact spaces, which involves inverse sequences of ``simple'' retractions. Consequently, a compact space of weight $\\loe\\aleph_1$ is Valdivia compact iff it is the limit of an inverse sequence of metric compacta whose bonding maps are retractions. As a corollary, we show that the class of Valdivia compacta of weight at most $\\aleph_1$ is preserved both under retractions and under open 0-dimensional images. Finally, we characterize the class of all Valdivia compacta in the language of category theory, which implies that this class is preserved under all continuous weight preserving functors.

Clustering of near clusters versus cluster compactness

International Nuclear Information System (INIS)

Yu Gao; Yipeng Jing

1989-01-01

The clustering properties of near Zwicky clusters are studied by using the two-point angular correlation function. The angular correlation functions for compact and medium compact clusters, for open clusters, and for all near Zwicky clusters are estimated. The results show much stronger clustering for compact and medium compact clusters than for open clusters, and that open clusters have nearly the same clustering strength as galaxies. A detailed study of the compactness-dependence of correlation function strength is worth investigating. (author)

Response Of Lowland Rice To Soil Compaction

International Nuclear Information System (INIS)

Idawati; Haryanto

2000-01-01

Soil compaction, as a new tillage practice for paddy soil, is to substitute pudding in order to reduce land preparation cost. To study response of lowland rice to soil compaction, a pot experiment has been conducted which took place in the greenhouse of P3TIR-BATAN. Soil for experiment was taken from pusakanegara. Two factors (degree of soil compaction and rice variety) were combined. Degree of compaction was split into 3 levels (DI = normal; D215% more compact than normal; 30 % more compact than normal), and rice variety into 2 levels (IR64 and Atomita IV). KH 2 32 PO 4 solution was injected into the soil surrounding rice clump to test the root activity at blooming stage of rice plant. Data resulted from this experiment is presented together with additional data from some other experiments of fertilization in the research s erie to study soil compaction. Some information's from experiment results are as following. Both rice varieties tested gave the same response to soil compaction. Root activity, according to data of 32 P absorbed by plant, was not harmed by soil compaction at the degree tested in the experiment. This prediction is supported by the growth by rice observed at generative growth stage, in pot experiment as well as in field experiment, which showed that soil compaction tested did not decrease rice yield but in opposite in tended to increase the yield. In practising soil compaction in land preparation, fertilizers should be applied by deep placement to have higher increasing is rice yield

Formation and evolution of compact binaries

NARCIS (Netherlands)

Sluijs, Marcel Vincent van der

2006-01-01

In this thesis we investigate the formation and evolution of compact binaries. Chapters 2 through 4 deal with the formation of luminous, ultra-compact X-ray binaries in globular clusters. We show that the proposed scenario of magnetic capture produces too few ultra-compact X-ray binaries to explain

Green Building Pro-Environment Behaviors: Are Green Users Also Green Buyers?

Directory of Open Access Journals (Sweden)

Xiaohuan Xie

2017-09-01

Full Text Available Pro-environment behaviors play a key role in advancing the development of green buildings. This study investigated the link between two green building pro-environment behaviors that require dissimilar resources: energy savings that do not require money in order to be more environmentally friendly and willingness to pay that involves economic resources including spending money in order to be more environmentally friendly. This study points out that the two pro-environment behaviors can be positively linked to each other. People who behave in an environmentally friendly manner at work would also be likely to pay an extra cost for a green building when buying a new home. The consistency of the two pro-environment behaviors can be explained by their common environmental beliefs: limits to growth and eco-crisis. The green building movement should prioritize pro-environmental behaviors and associated environmental beliefs to support green building policies, guidelines, and tools.

Differing Event-Related Patterns of Gamma-Band Power in Brain Waves of Fast- and Slow-Reacting Subjects

Science.gov (United States)

1994-05-01

Wilhelm Wundt proposed that there are two types of subjects in sim- ple RT experiments: fast-reacting subjects, who respond before they fully...quickly as possible to auditory stimuli. This result appears to confirm long-standing speculations of Wundt that fast- and slow-reacting subjects...accord with the hypothesis of Wundt and others that slower ("sensorial") responders wait to fully perceive a stimulus and then react to their perception

Step-by-Step Simulation of Radiation of Radiation Chemistry Using Green Functions for Diffusion-Influenced Reactions

Science.gov (United States)

Plante, Ianik; Cucinotta, Francis A.

2011-01-01

The irradiation of biological systems leads to the formation of radiolytic species such as H(raised dot), (raised dot)OH, H2, H2O2, e(sup -)(sub aq), etc.[1]. These species react with neighboring molecules, which result in damage in biological molecules such as DNA. Radiation chemistry is there for every important to understand the radiobiological consequences of radiation[2]. In this work, we discuss an approach based on the exact Green Functions for diffusion-influenced reactions which may be used to simulate radiation chemistry and eventually extended to study more complex systems, including DNA.

Equationally Compact Acts : Coproducts / Peeter Normak

Index Scriptorium Estoniae

Normak, Peeter

1998-01-01

In this article equational compactness of acts and its generalizations are discussed. As equational compactness does not carry over to coproducts a slight generalization of c-equational campactness is introduced. It is proved that a coproduct of acts is c-equationally compact if and only if all components are c-equationally campact

The United Nations Global Compact

DEFF Research Database (Denmark)

Rasche, Andreas; Waddock, Sandra; McIntosh, Malcolm

2013-01-01

This article reviews the interdisciplinary literature on the UN Global Compact. The review identifies three research perspectives, which scholars have used to study the UN Global Compact so far: a historical perspective discussing the Global Compact in the context of UN-business relations...... key empirical as well as conceptual scholarly contributions. The remainder of this article contains focused summaries of the articles selected for this Special Issue. All articles are introduced and evaluated against the background of the three research perspectives....

Autoshaping with common and distinctive stimulus elements, compact and dispersed arrays1

Science.gov (United States)

Sperling, Sally E.; Perkins, Mark E.

1979-01-01

Four groups of pigeons were trained with a standard autoshaping procedure in which a brief fixed-duration interval always followed by a grain delivery alternated with a longer variable-duration interval never associated with grain delivery. One of two stimuli was always presented during each interval. One of them contained three black dots and a black star on a green background; the other contained four black dots on a green background. The four elements of each stimulus were arranged in a more compact array for two groups and in a more dispersed array for the other two groups. Which of the two stimuli preceded grain delivery was counterbalanced within each pair of groups. The speed of occurrence of the first autoshaped peck was not affected by whether the stimulus containing the distinctive star element preceded grain delivery, but autoshaping was faster when the stimulus arrays were compact than when they were dispersed. During 560 response-independent training trials that followed the first autoshaped peck, this pattern reversed; both discriminative control over responding and the relative frequency of pecking the stimulus that preceded grain delivery were greater for the two groups where this stimulus contained the discriminative element than for the two groups where it contained only common elements. During subsequent testing with stimuli containing only a single element each, the distinctive feature was responded to proportionately more often by the two groups for which it had been an element of the stimulus preceding grain delivery than by the two groups for which it had been an element of the stimulus complex that never was associated with grain delivery. These data add further support to the hypothesis that the initial occurrence of autoshaped responding and its subsequent maintenance are not affected by the same variables. They also suggest that automaintenance is as sensitive as response-dependent training to the presence or absence of a distinctive

Compaction of spent nuclear fuel cans

International Nuclear Information System (INIS)

Sullivan, H.

1985-01-01

Hydraulic press apparatus for compacting waste material eg. spent nuclear fuel cans comprises a fixed frame, a movable cross head, a press crown and three groups of piston/cylinder devices; having their pistons connected to the cross head and their cylinders secured to the press crown. A control means connects the first group of devices to hydraulic fluid in a reservoir which is pressurised initially by gas from gas accumulators to move the cross head and a quill secured thereto towards the frame base to compact the waste at a first high rate under a first high loading. Compaction then proceeds at a lower second rate at a lower second loading as the hydraulic fluid in the reservoir is pressurised by a pump. At two subsequent stages of compaction of the waste at which resistance increases causing a pressure rise in cylinders the control means causes hydraulic fluid to be passed to the second group of devices and thence to the third group of devices, the compaction rate reducing at each stage but the compaction force increasing. (author)

Generation of 46 W green-light by frequency doubling of 96 W picosecond unpolarized Yb-doped fiber amplifier

Science.gov (United States)

Qi, Yaoyao; Yu, Haijuan; Zhang, Jingyuan; Zhang, Ling; He, Chaojian; Lin, Xuechun

2018-05-01

We demonstrated a high efficiency and high average power picosecond green light source based on SHG (second harmonic generation) of an unpolarized ytterbium-doped fiber amplifier chain. Using single-pass frequency doubling in two temperature-tuned type-I phase-matching LBO crystals, we were able to generate 46 W, >70 ps pulses at 532 nm from a fundamental beam at 1064 nm, whose output is 96 W, 4.8 μJ, with a repetition frequency of 20 MHz and nearly diffraction limited. The optical conversion efficiency was ∼48% in a highly compact design. To the best of our knowledge, this is the first reported on ps green source through SHG of an unpolarized fiber laser with such a high output and high efficiency.

Iodine-stabilized single-frequency green InGaN diode laser.

Science.gov (United States)

Chen, Yi-Hsi; Lin, Wei-Chen; Shy, Jow-Tsong; Chui, Hsiang-Chen

2018-01-01

A 520-nm InGaN diode laser can emit a milliwatt-level, single-frequency laser beam when the applied current slightly exceeds the lasing threshold. The laser frequency was less sensitive to diode temperature and could be finely tuned by adjusting the applied current. Laser frequency was stabilized onto a hyperfine component in an iodine transition through the saturated absorption spectroscopy. The uncertainty of frequency stabilization was approximately 8×10 -9 at a 10-s integration time. This compact laser system can replace the conventional green diode-pumped solid-state laser and applied as a frequency reference. A single longitudinal mode operational region with diode temperature, current, and output power was investigated.

Physically detached 'compact groups'

Science.gov (United States)

Hernquist, Lars; Katz, Neal; Weinberg, David H.

1995-01-01

A small fraction of galaxies appear to reside in dense compact groups, whose inferred crossing times are much shorter than a Hubble time. These short crossing times have led to considerable disagreement among researchers attempting to deduce the dynamical state of these systems. In this paper, we suggest that many of the observed groups are not physically bound but are chance projections of galaxies well separated along the line of sight. Unlike earlier similar proposals, ours does not require that the galaxies in the compact group be members of a more diffuse, but physically bound entity. The probability of physically separated galaxies projecting into an apparent compact group is nonnegligible if most galaxies are distributed in thin filaments. We illustrate this general point with a specific example: a simulation of a cold dark matter universe, in which hydrodynamic effects are included to identify galaxies. The simulated galaxy distribution is filamentary and end-on views of these filaments produce apparent galaxy associations that have sizes and velocity dispersions similar to those of observed compact groups. The frequency of such projections is sufficient, in principle, to explain the observed space density of groups in the Hickson catalog. We discuss the implications of our proposal for the formation and evolution of groups and elliptical galaxies. The proposal can be tested by using redshift-independent distance estimators to measure the line-of-sight spatial extent of nearby compact groups.

Green thunderstorms

Science.gov (United States)

Gallagher, Frank Woolsey, III

Many people around the world have observed green light apparently emanating from severe thunderstorms, but until recently there has been no scientific study of the phenomenon. Green thunderstorms have been observed from time to time in association with deep convection or severe weather events. Some skeptics who have not personally observed a green thunderstorm suggest that they are some kind of illusion. The existence of green thunderstorms has been objectively demonstrated by recording spectra of light from thunderstorms using a handheld spectrophotometer. During the spring and summer of 1995 and the spring of 1996 numerous storms were observed and spectra of the light emanating from these storms were recorded. Observations were made both at the ground and aboard research aircraft. Furthermore, time series of spectra were recorded as the observed color of some storms changed from dark blue to a bluish-green. Several hypotheses have been advanced to explain the occurrence of green light in connection with severe storms. Fankhauser gave some observational support to the belief that green light from thunderstorms is possible and believed that the source of the light is from the blue sky penetrating thin regions in the clouds. Fraser believes that light from the setting sun, in combination with the process of scattering by atmospheric molecules, creates the green light associated with severe weather and the thunderstorm acts only as a black backdrop. Unfortunately, no cloud illuminated by the sun is black and the green airlight produced by the Fraser theory is in reality overwhelmed by light reflected by the cloud. Often the unusual coloration has been attributed to hail or to reflection of light from foliage on the ground. The quantitative measurements made during the observation period fail to support these assumptions. We have observed thunderstorms to be green over ground that was not green and we have observed blue thunderstorms over ground that was green

Study on flow characteristics of chemically reacting liquid jet

International Nuclear Information System (INIS)

Hong Seon Dae; Okamoto, Koji; Takata, Takashi; Yamaguchi, Akira

2004-07-01

Tube rupture accidents in steam generators of sodium-cooled fast breeder reactors are important for safety because the rupture may propagates to neighboring tubes due to sodium-water reaction. In order to clarify the thermal-hydraulic phenomena in the accidents, the flow pattern and the interface in multi-phase flow must be investigated. The JNC cooperative research scheme on the nuclear fuel cycle with the University of Tokyo has been carried to develop a simultaneous measurement system of concentration and velocity profiles and to evaluate influence of chemical reaction on mixing phenomena. In the experiments, aqueous liquor of acetic acid and ammonium hydroxide are selected as a simulant fluid instead of liquid sodium and water vapor. The following conclusions are obtained in this research. Laser Induced Fluorescence (LIF) technique was adopted to measure reacting zone and pH distribution in chemically reacting liquid round free jet. As a result, it was found that the chemical reaction, which took place at the interface between the jet and outer flow, suppressed the mixing phenomenon (in 2001 research). Dynamic Particle Image Velocimetry (PIV) method was developed to measure instantaneous velocity profile with high temporal resolution. In the Dynamic PIV, a high-speed video camera coupled with a high-speed laser pulse generator was implemented. A time-line trend of interfacial area in the free jet was investigated with the Dynamic PIV. This technique was also applied to a complicated geometry (in 2002 research). A new algorithms for image analysis was developed to evaluated the Dynamic PIV data in detail. The characteristics of the mixing phenomenon with reacting jet such as the turbulent kinetic energy and the Reynolds stress were estimated in a spatial and temporal spectrum (in 2003 research). (author)

Peculiarities of powder brittle media compaction

International Nuclear Information System (INIS)

Perel'nam, V.E.; Aristarkhov, A.I.

1981-01-01

The paper is concerned with theoretical and practical aspects of the compaction process for powders of almost unstrained materials. Consideration from the standpoint of compressible body strain mechanics shows that such porous media may have a certain ''threshold'' density. Ductile characteristics of the porous material compacted up to this extent are identical with properties of compacrat bodies, i.e. there is a theoretically substantiated ban on a possibility of their further compaction without changing the state of the powder particle material. Theoretical conclusions are confirmed by results of experimental studies in compaction of titanium- containing ceramics [ru

Cultural Ecosystem Services of Urban Green Spaces-Supply and Demand in The Densely Built-Up Areas. Poznan Old Town Case Study

Science.gov (United States)

Ponizy, Lidia; Majchrzak, Weronika; Zwierzchowska, Iwona

2017-12-01

The quality of life of big city dwellers depends on the use of green infrastructure. The idea of a compact city, opposed to urban sprawl, can lead to reduced access to green areas and increased demand for cultural services provided through urban green infrastructure. Considering the above, the aim of the paper was to identify the supply of and demand for cultural ecosystem services related to the urban green spaces in densely built-up urban areas. To find out how important the ability to use green areas for dwellers of the densely built-up areas is, the questionnaire interviews with the residents of the area of the Old Town of Poznan were conducted. Questions in the survey concerned the amount of green spaces and their availability, the way of use, types of activity, factors limiting the use and factors encouraging to visit green spaces and the motives for using green areas away from inhabitants’ place of residence. Respondents claim that there is not enough greenery, especially associated with housing and street side greenery; the amount of parks (which they use most) is slightly higher, in their opinion. Limitations that influence utilising green spaces concern both greenery itself (e.g. insufficient recreational infrastructure, neglected green areas) as well as respondent’s issues (e.g. lack of free time). Improvements to recreational infrastructure and more well-kept green spaces would encourage respondents to utilise it more often. Active participation of inhabitants in developing and maintaining their closest neighbourhood would allow to enlarge green spaces in housing areas and make them more customized to the residents’ needs and requirements in terms of functionality and aesthetic.

Implementation of a spark plasma sintering facility in a hermetic glovebox for compaction of toxic, radiotoxic, and air sensitive materials

Energy Technology Data Exchange (ETDEWEB)

Tyrpekl, V., E-mail: vaclav.tyrpekl@ec.europa.eu, E-mail: vaclav.tyrpekl@gmail.com; Berkmann, C.; Holzhäuser, M.; Köpp, F.; Cologna, M.; Somers, J. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany); Wangle, T. [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU), Postfach 2340, 76125 Karlsruhe (Germany); Faculty of Nuclear Sciences and Physical Engineering, Czech Technical University in Prague, Břehová 7, Praha 1, 115 19 (Czech Republic)

2015-02-15

Spark plasma sintering (SPS) is a rapidly developing method for densification of powders into compacts. It belongs to the so-called “field assisted sintering techniques” that enable rapid sintering at much lower temperatures than the classical approaches of pressureless sintering of green pellets or hot isostatic pressing. In this paper, we report the successful integration of a SPS device into a hermetic glovebox for the handling of highly radioactive material containing radioisotopes of U, Th, Pu, Np, and Am. The glovebox implantation has been facilitated by the replacement of the hydraulic system to apply pressure with a compact electromechanical unit. The facility has been successfully tested using UO{sub 2} powder. Pellets with 97% of the theoretical density were obtained at 1000 °C for 5 min, significantly lower than the ∼1600 °C for 5-10 h used in conventional pellet sintering.

Green-manure turnip for soybean based no-tillage farming systems in eastern Paraguay

Directory of Open Access Journals (Sweden)

Kubota Aki

2005-01-01

Full Text Available A no-tillage soybean-wheat cropping system has been practiced for many years on the "Terra Rossa" soils of eastern Paraguay. Soil compactness and soil erosion have recently been identified as potential problems. This study examines the effect of replacing unprofitable wheat by green-manure turnip (Raphanus sativus L. var. oleiferus Metzg. on soil properties and soybean production. Gaseous phase, porosity, bulk density, water saturation, cone index, pH, exchangeable-cations, available-phosphorus (P and aggregate size distribution of the soil were measured. Contrary to initial expectations, turnip did not reduce soil compactness. Instead, turnip stabilized the aggregate structure of the surface soil. Positive effects of turnip on subsequent soybean growth and yield were detected in a rather dry year but not in an exceptionally wet year. In a second part of this study, nutrient return from turnip and wheat residues were compared. Turnip produced 10.7 t ha-1 of shoot dry matter, and absorbed 294, 27, 302, 175, and 33 kg ha-1 of N, P, K, Ca, and Mg, respectively. Wheat absorbed 98, 11, 67, 11, and 7 kg ha-1 of N, P, K, Ca, and Mg, respectively. About 75% of the N absorbed by wheat was removed from the field at harvest whereas most nutrients in the turnip residue were returned to the soil before planting of soybeans with positive effects on soil fertility. Additional benefits of green-manure turnip would include a reduced chance for erosion through improvements in aggregate structure and through a more complete soil cover.

Green shipping management

CERN Document Server

Lun, Y H Venus; Wong, Christina W Y; Cheng, T C E

2016-01-01

This book presents theory-driven discussion on the link between implementing green shipping practices (GSP) and shipping firm performance. It examines the shipping industry’s challenge of supporting economic growth while enhancing environmental performance. Consisting of nine chapters, the book covers topics such as the conceptualization of green shipping practices (GSPs), measurement scales for evaluating GSP implementation, greening capability, greening and performance relativity (GPR), green management practice, green shipping network, greening capacity, and greening propensity. In view of the increasing quest for environment protection in the shipping sector, this book provides a good reference for firms to understand and evaluate their capability in carrying out green operations on their shipping activities.

EPRI compact analyzer: A compact, interactive and color-graphics based simulator for power plant analysis

International Nuclear Information System (INIS)

Ipakchi, A.; Khadem, M.; Chen, H.; Colley, R.W.

1986-01-01

This paper presents the results of an EPRI sponsored project (RP2395-2) for design and development of an interactive, and color graphics based simulator for power plant analysis. The system is called Compact Analyzer and can be applied to engineering and training applications in the utility industry. The Compact Analyzer's software and system design are described. Results of two demonstration system for a nuclear plant, and a fossil plant are presented, and the applications of the Compact Analyzer to operating procedures evaluation are discussed

The Future Concrete: Self-Compacting Concrete

OpenAIRE

Iureş, Liana; Bob, Corneliu

2010-01-01

The paper presents the characteristics of the self-compacting concretes, their advantages and disadvantages when they are used in buildings. Due to its properties and composition, the self-compacting concrete is described here as being one of the future friendly enviromental material for buildings. Tests concerning to obtaining a self-compacting concrete, together with the specific fresh concrete properties tests, are described.

Green Consumerism : an Eco-Friendly Behaviour Form Through The Green Product Consumption and Green Marketing

Directory of Open Access Journals (Sweden)

Wiwik Handayani

2017-09-01

Full Text Available This research is referred to analyse the influence of consumer attitude of green product towards purchase intention. The consumer attitude of green product is a psychological tendencies that is expressed by evaluating a certain entity with some advantage or disadvantage considerations. The problem of this research is the low of cunsumer awareness to consume green product, because the lack to comprehend the importance of green product usage for health and eco-friendly. The purpose of this research is to test the influence of consumer attitude of green products towards purchase intention. Hypothesis testing using Partial Least Square (PLS. The result of analysis show that there is influence among consumer attitude of green product towards consumer purchase intention significantly.

Unfolding Green Defense

DEFF Research Database (Denmark)

Larsen, Kristian Knus

2015-01-01

In recent years, many states have developed and implemented green solutions for defense. Building on these initiatives NATO formulated the NATO Green Defence Framework in 2014. The framework provides a broad basis for cooperation within the Alliance on green solutions for defense. This report aims...... to inform and support the further development of green solutions by unfolding how green technologies and green strategies have been developed and used to handle current security challenges. The report, initially, focuses on the security challenges that are being linked to green defense, namely fuel...... consumption in military operations, defense expenditure, energy security, and global climate change. The report then proceeds to introduce the NATO Green Defence Framework before exploring specific current uses of green technologies and green strategies for defense. The report concludes that a number...

Powder compaction in systems of bimodal distribution

Science.gov (United States)

Chattopadhyay, A. K.; Whittemore, O. J., Jr.

1973-01-01

The compaction of mixtures involving different particle sizes is discussed. The various stages of the compaction process include the rearrangement of particles, the filling of the interstices of the large particles by the smaller ones, and the change in particle size and shape upon further densification through the application of pressure. Experimental approaches and equipment used for compacting material are discussed together with the theoretical relations of the compacting process.

[A surface reacted layer study of titanium-zirconium alloy after dental casting].

Science.gov (United States)

Zhang, Y; Guo, T; Li, Z; Li, C

2000-10-01

To investigate the influence of the mold temperature on the surface reacted layer of Ti-Zr alloy castings. Ti-Zr alloy was casted into a mold which was made of a zircon (ZrO2.SiO2) for inner coating and a phosphate-bonded material for outer investing with a casting machine (China) designed as vacuum, pressure and centrifuge. At three mold temperatures (room temperature, 300 degrees C, 600 degrees C) the Ti-Zr alloy was casted separately. The surface roughness of the castings was calculated by instrument of smooth finish (China). From the surface to the inner part the Knoop hardness and thickness in reacted layer of Ti-Zr alloy casting was measured. The structure of the surface reacted layer was analysed by SEM. Elemental analyses of the interfacial zone of the casting was made by element line scanning observation. The surface roughness of the castings was increased significantly with the mold temperature increasing. At a higher mold temperature the Knoop hardness of the reactive layer was increased. At the three mold temperature the outmost surface was very hard, and microhardness data decreased rapidly where they reached constant values. The thickness was about 85 microns for castings at room temperature and 300 degrees C, 105 microns for castings at 600 degrees C. From the SEM micrograph of the Ti-Zr alloy casting, the surface reacted layer could be divided into three different layers. The first layer was called non-structure layer, which thickness was about 10 microns for room temperature group, 20 microns for 300 degrees C and 25 microns for 600 degrees C. The second layer was characterized by coarse-grained acicular crystal, which thickness was about 50 microns for three mold temperatures. The third layer was Ti-Zr alloy. The element line scanning showed non-structure layer with higher level of element of O, Al, Si and Zr, The higher the mold temperature during casting, the deeper the Si permeating and in the second layer the element Si could also be found

Compact vortices

Energy Technology Data Exchange (ETDEWEB)

Bazeia, D.; Losano, L.; Marques, M.A.; Zafalan, I. [Universidade Federal da Paraiba, Departamento de Fisica, Joao Pessoa, PB (Brazil); Menezes, R. [Universidade Federal da Paraiba, Departamento de Ciencias Exatas, Rio Tinto, PB (Brazil); Universidade Federal de Campina Grande, Departamento de Fisica, Campina Grande, PB (Brazil)

2017-02-15

We study a family of Maxwell-Higgs models, described by the inclusion of a function of the scalar field that represent generalized magnetic permeability. We search for vortex configurations which obey first-order differential equations that solve the equations of motion. We first deal with the asymptotic behavior of the field configurations, and then implement a numerical study of the solutions, the energy density and the magnetic field. We work with the generalized permeability having distinct profiles, giving rise to new models, and we investigate how the vortices behave, compared with the solutions of the corresponding standard models. In particular, we show how to build compact vortices, that is, vortex solutions with the energy density and magnetic field vanishing outside a compact region of the plane. (orig.)

Compaction monitoring in the Ekofisk area Chalk Fields

International Nuclear Information System (INIS)

Menghini, M.L.

1989-01-01

In late Nov. 1984, the subsidence phenomenon was recognized in the Ekofisk field. To determine the magnitude and areal extent of the formation compaction, a program for measuring compaction with electric logging tools was initiated. Initial time-lapse surveys performed with cased-hole neutron tools indicated that reservoir compaction was occurring, but the accuracy of the determination of compaction rate was low. In addition to the cased-hole neutron survey, radioactive markers and a gamma ray (GR) detection tool were used to determine compaction rate in the reservoir more accurately and to determine whether compaction was occurring in the overburden. A program for implanting radioactive-marker bullets and subsequent monitoring with a four-detector GR tool was implemented. There are currently 13 wells equipped with radioactive markers in the compaction monitoring program. Compaction monitoring accuracy using the four-detector GR tool was found to depend on wellbore geometry, completion design, and radioactive-marker placement. This paper gives the results of the program to date and describes the operational procedures and analysis techniques used for compaction monitoring in the greater Ekofisk area chalk fields

Experimental thermodynamics experimental thermodynamics of non-reacting fluids

CERN Document Server

Neindre, B Le

2013-01-01

Experimental Thermodynamics, Volume II: Experimental Thermodynamics of Non-reacting Fluids focuses on experimental methods and procedures in the study of thermophysical properties of fluids. The selection first offers information on methods used in measuring thermodynamic properties and tests, including physical quantities and symbols for physical quantities, thermodynamic definitions, and definition of activities and related quantities. The text also describes reference materials for thermometric fixed points, temperature measurement under pressures, and pressure measurements. The publicatio

Does soil compaction increase floods? A review

Science.gov (United States)

Alaoui, Abdallah; Rogger, Magdalena; Peth, Stephan; Blöschl, Günter

2018-02-01

Europe has experienced a series of major floods in the past years which suggests that flood magnitudes may have increased. Land degradation due to soil compaction from crop farming or grazing intensification is one of the potential drivers of this increase. A literature review suggests that most of the experimental evidence was generated at plot and hillslope scales. At larger scales, most studies are based on models. There are three ways in which soil compaction affects floods at the catchment scale: (i) through an increase in the area affected by soil compaction; (ii) by exacerbating the effects of changes in rainfall, especially for highly degraded soils; and (iii) when soil compaction coincides with soils characterized by a fine texture and a low infiltration capacity. We suggest that future research should focus on better synthesising past research on soil compaction and runoff, tailored field experiments to obtain a mechanistic understanding of the coupled mechanical and hydraulic processes, new mapping methods of soil compaction that combine mechanical and remote sensing approaches, and an effort to bridge all disciplines relevant to soil compaction effects on floods.

Metaphysical green

DEFF Research Database (Denmark)

Earon, Ofri

2011-01-01

example is a tiny Danish summer house from 1918 . The second example is ‘House before House’ , in Tokyo. The third example is a prefabricated house ‘CHU’ . The analysis evaluates the characteristics of diverse tones of green – from green image to green sensation. The analysis is based on the original...... of Sensation of Green is created by a physical interaction between the language of space and the language of nature” The notion of Sensation of Green was developed through a previous study ‘Learning from the Summer House’ investigating the unique architectural characteristics of the Danish summer houses...... the Sensation of Green? Three existing examples are agents to this discussion. The first example is a Danish summer house. The other two are international urban examples. While the summer house articulates the original meaning of Sensation of Green, the urban examples illustrate its urban context. The first...

Direct numerical simulation of turbulent, chemically reacting flows

Science.gov (United States)

Doom, Jeffrey Joseph

This dissertation: (i) develops a novel numerical method for DNS/LES of compressible, turbulent reacting flows, (ii) performs several validation simulations, (iii) studies auto-ignition of a hydrogen vortex ring in air and (iv) studies a hydrogen/air turbulent diffusion flame. The numerical method is spatially non-dissipative, implicit and applicable over a range of Mach numbers. The compressible Navier-Stokes equations are rescaled so that the zero Mach number equations are discretely recovered in the limit of zero Mach number. The dependent variables are co--located in space, and thermodynamic variables are staggered from velocity in time. The algorithm discretely conserves kinetic energy in the incompressible, inviscid, non--reacting limit. The chemical source terms are implicit in time to allow for stiff chemical mechanisms. The algorithm is readily applicable to complex chemical mechanisms. Good results are obtained for validation simulations. The algorithm is used to study auto-ignition in laminar vortex rings. A nine species, nineteen reaction mechanism for H2/air combustion proposed by Mueller et al. [37] is used. Diluted H 2 at ambient temperature (300 K) is injected into hot air. The simulations study the effect of fuel/air ratio, oxidizer temperature, Lewis number and stroke ratio (ratio of piston stroke length to diameter). Results show that auto--ignition occurs in fuel lean, high temperature regions with low scalar dissipation at a 'most reactive' mixture fraction, zeta MR (Mastorakos et al. [32]). Subsequent evolution of the flame is not predicted by zetaMR; a most reactive temperature TMR is defined and shown to predict both the initial auto-ignition as well as subsequent evolution. For stroke ratios less than the formation number, ignition in general occurs behind the vortex ring and propagates into the core. At higher oxidizer temperatures, ignition is almost instantaneous and occurs along the entire interface between fuel and oxidizer. For stroke

Effects of sintering time and temperature to the characteristics of FeCrAl powder compacts formed at elevated temperature

Science.gov (United States)

Rahman, M. M.; Rahman, H. Y.; Awang, M. A. A.; Sopyan, I.

2018-01-01

This paper presents the outcomes of an experimental investigation on the effect of sintering schedule, i.e., holding time and temperature to the final properties of FeCrAl powder compacts prepared through uniaxial die compaction process at above room temperature. The feedstock was prepared by mechanically mixing iron powder ASC 100.29 with chromium (22 wt%) and aluminium (11 wt%) for 30 min at room temperature. A cylindrical shape die was filled with the powder mass and heated for one hour for uniform heating of the die assembly together with the powder mass. Once the temperature reached to the setup temperature, i.e., 150°C, the powder mass was formed by applying an axial pressure of 425 MPa simultaneously from upward and downward directions. The as-pressed green compacts were then cooled to room temperature and subsequently sintered in argon gas fired furnace at a rate of 5°C/min for three different holding times, i.e., 30, 60, and 90 min at three different sintering temperatures, i.e., 800, 900, and 1000°C. The sintered samples were characterized for their density, electrical resistivity, bending strength, and microstructure. The results revealed that the sample sintered at 1000°C for 90 min achieved the better characteristics.

The Future Concrete: Self-Compacting Concrete

Directory of Open Access Journals (Sweden)

Liana Iureş

2010-01-01

Full Text Available The paper presents the characteristics of the self-compacting concretes, their advantages and disadvantages when they are used in buildings. Due to its properties and composition, the self-compacting concrete is described here as being one of the future friendly enviromental material for buildings. Tests concerning to obtaining a self-compacting concrete, together with the specific fresh concrete properties tests, are described.

The Influence of Consumers Perception of Green Products on Green Purchase Intention

OpenAIRE

Wilson Kong; Amran Harun; Rini Suryati Sulong; Jaratin Lily

2014-01-01

Green consumerism has increasingly received attention since the increased level of consumer awareness towards green products. Therefore, the aim of this paper had been to examine the influence of consumer perception of green products on green purchase intention. In this study, perception of green products was conceptualized as a multidimensional variable comprised of green corporate perception, eco-label, green advertising, green packaging, and green product value. By using a survey, a total ...

Does the StartReact Effect Apply to First-Trial Reactive Movements?

Directory of Open Access Journals (Sweden)

Katrin Sutter

Full Text Available StartReact is the acceleration of reaction time by a startling acoustic stimulus (SAS. The SAS is thought to release a pre-prepared motor program. Here, we investigated whether the StartReact effect is applicable to the very first trial in a series of repeated unpractised single-joint movements.Twenty healthy young subjects were instructed to perform a rapid ankle dorsiflexion movement in response to an imperative stimulus. Participants were divided in two groups of ten. Both groups performed 17 trials. In one group a SAS (116 dB was given in the first trial, whereas the other group received a non-startling sound (70 dB as the first imperative stimulus. In the remaining 16 trials, the SAS was given as the imperative stimulus in 25% of the trials in both groups. The same measurement was repeated one week later, but with the first-trial stimuli counterbalanced between groups.When a SAS was given in the very first trial, participants had significantly shorter onset latencies compared to first-trial responses to a non-startling stimulus. Succeeding trials were significantly faster compared to the first trial, both for trials with and without a SAS. However, the difference between the first and succeeding trials was significantly larger for responses to a non-startling stimulus compared to responses triggered by a SAS. SAS-induced acceleration in the first trial of the second session was similar to that in succeeding trials of session 1.The present results confirm that the StartReact phenomenon also applies to movements that have not yet been practiced in the experimental context. The excessive SAS-induced acceleration in the very first trial may be due to the absence of integration of novel context-specific information with the existing motor memory for movement execution. Our findings demonstrate that StartReact enables a rapid release of motor programs in the very first trial also without previous practice, which might provide a behavioural

Prediction for swelling characteristics of compacted bentonite

International Nuclear Information System (INIS)

Komine, H.; Ogata, N.

1996-01-01

Compacted bentonites are attracting greater attention as back-filling (buffer) materials for high-level nuclear waste repositories. For this purpose, it is very important to quantitatively evaluate the swelling characteristics of compacted bentonite. New equations for evaluating the relationship between the swelling deformation of compacted bentonite and the distance between two montmorillonite layers are derived. New equations for evaluating the ion concentration of pore water and the specific surface of bentonite, which significantly influence the swelling characteristics of compacted bentonite, are proposed. Furthermore, a prediction method for the swelling characteristics of compacted bentonite is presented by combining the new equations with the well-known theoretical equations of repulsive and attractive forces between two montmorillonite layers. The applicability of this method was investigated by comparing the predicted results with laboratory test results on the swelling deformation and swelling pressure of compacted bentonites. (author) 31 refs., 8 tabs., 12 figs

Direct numerical simulation of turbulent reacting flows

Energy Technology Data Exchange (ETDEWEB)

Chen, J.H. [Sandia National Laboratories, Livermore, CA (United States)

1993-12-01

The development of turbulent combustion models that reflect some of the most important characteristics of turbulent reacting flows requires knowledge about the behavior of key quantities in well defined combustion regimes. In turbulent flames, the coupling between the turbulence and the chemistry is so strong in certain regimes that is is very difficult to isolate the role played by one individual phenomenon. Direct numerical simulation (DNS) is an extremely useful tool to study in detail the turbulence-chemistry interactions in certain well defined regimes. Globally, non-premixed flames are controlled by two limiting cases: the fast chemistry limit, where the turbulent fluctuations. In between these two limits, finite-rate chemical effects are important and the turbulence interacts strongly with the chemical processes. This regime is important because industrial burners operate in regimes in which, locally the flame undergoes extinction, or is at least in some nonequilibrium condition. Furthermore, these nonequilibrium conditions strongly influence the production of pollutants. To quantify the finite-rate chemistry effect, direct numerical simulations are performed to study the interaction between an initially laminar non-premixed flame and a three-dimensional field of homogeneous isotropic decaying turbulence. Emphasis is placed on the dynamics of extinction and on transient effects on the fine scale mixing process. Differential molecular diffusion among species is also examined with this approach, both for nonreacting and reacting situations. To address the problem of large-scale mixing and to examine the effects of mean shear, efforts are underway to perform large eddy simulations of round three-dimensional jets.

Green Belts as a Means of Managing the Landscape at the Edge of the City

Directory of Open Access Journals (Sweden)

Cliff Hague

2015-11-01

Full Text Available This paper will review the theory and practice of green belts as instruments of urban containment in a European context. It will point to the emphasis given to the compact city in the European Spatial Development Perspective. It will then review and compare some of the practices in different parts of Europe. Particular emphasis will be given to a comparison of policy and implementation in Scotland and the Netherlands.The analysis will show that green belts are used to pursue a number of policy aims:they are not exclusively a tool to manage landscape resources. Furthermore they have social and economic impacts as well as landscape impacts. There are also important questions about the relation between policy and implementation. Finally recommendations are made for a more active design and management approach to planning land at the edge of the city as part of strategic spatial planning practice. 

Green Tourism

OpenAIRE

Hasan, Ali

2014-01-01

Green tourism is defined as environmentally friendly tourism activities with various focuses and meanings. In a broad term, green tourism is about being an environmentally friendly tourist or providing environmentally friendly tourist services. The green tourism concept would be highly appealing to tourism enterprises and operators owing to increasing governmental pressure to improve environmental performance by adopting effective and tangible environmental management techniques. Green to...

Low Mach number asymptotics for reacting compressible fluid flows

Czech Academy of Sciences Publication Activity Database

Feireisl, Eduard; Petzeltová, Hana

2010-01-01

Roč. 26, č. 2 (2010), s. 455-480 ISSN 1078-0947 R&D Projects: GA ČR GA201/05/0164 Institutional research plan: CEZ:AV0Z10190503 Keywords : low Mach number * Navier-Stokes-Fourier system * reacting fluids Subject RIV: BA - General Mathematics Impact factor: 0.986, year: 2010 http://www.aimsciences.org/journals/displayArticles.jsp?paperID=4660

A Green Bank Telescope 21cm survey of HI clouds in the Milky Way's nuclear wind

Science.gov (United States)

Denbo, Sara; Endsley, Ryan; Lockman, Felix J.; Ford, Alyson

2015-01-01

Feedback processes such as large-scale galactic winds are thought to be responsible for distributing enriched gas throughout a galaxy and even into the IGM. Such winds have been found in many galaxies with active star formation near their center, and the Fermi bubbles provide evidence for such a nuclear wind in our own Milky Way. A recent 21 cm HI survey by the Australia Telescope Compact Array discovered a population of compact, isolated clouds surrounding the Galactic Center that may be entrained in the Fermi bubble wind. We present data from a survey of 21cm HI over an extended region around the Galactic Center using the Green Bank Telescope. These observations provide more strict constraints on neutral clouds in the Fermi bubble wind, and a more robust description of the parameters of HI clouds (i.e., mass, column density, and lifetime) near the Galactic Center.

Deep Compaction Control of Sandy Soils

Directory of Open Access Journals (Sweden)

Bałachowski Lech

2015-02-01

Full Text Available Vibroflotation, vibratory compaction, micro-blasting or heavy tamping are typical improvement methods for the cohesionless deposits of high thickness. The complex mechanism of deep soil compaction is related to void ratio decrease with grain rearrangements, lateral stress increase, prestressing effect of certain number of load cycles, water pressure dissipation, aging and other effects. Calibration chamber based interpretation of CPTU/DMT can be used to take into account vertical and horizontal stress and void ratio effects. Some examples of interpretation of soundings in pre-treated and compacted sands are given. Some acceptance criteria for compaction control are discussed. The improvement factors are analysed including the normalised approach based on the soil behaviour type index.

Algebraic Bethe ansatz for U(1) invariant integrable models: Compact and non-compact applications

International Nuclear Information System (INIS)

Martins, M.J.; Melo, C.S.

2009-01-01

We apply the algebraic Bethe ansatz developed in our previous paper [C.S. Melo, M.J. Martins, Nucl. Phys. B 806 (2009) 567] to three different families of U(1) integrable vertex models with arbitrary N bond states. These statistical mechanics systems are based on the higher spin representations of the quantum group U q [SU(2)] for both generic and non-generic values of q as well as on the non-compact discrete representation of the SL(2,R) algebra. We present for all these models the explicit expressions for both the on-shell and the off-shell properties associated to the respective transfer matrices eigenvalue problems. The amplitudes governing the vectors not parallel to the Bethe states are shown to factorize in terms of elementary building blocks functions. The results for the non-compact SL(2,R) model are argued to be derived from those obtained for the compact systems by taking suitable N→∞ limits. This permits us to study the properties of the non-compact SL(2,R) model starting from systems with finite degrees of freedom.

Algebraic Bethe ansatz for U(1) invariant integrable models: Compact and non-compact applications

Science.gov (United States)

Martins, M. J.; Melo, C. S.

2009-10-01

We apply the algebraic Bethe ansatz developed in our previous paper [C.S. Melo, M.J. Martins, Nucl. Phys. B 806 (2009) 567] to three different families of U(1) integrable vertex models with arbitrary N bond states. These statistical mechanics systems are based on the higher spin representations of the quantum group U[SU(2)] for both generic and non-generic values of q as well as on the non-compact discrete representation of the SL(2,R) algebra. We present for all these models the explicit expressions for both the on-shell and the off-shell properties associated to the respective transfer matrices eigenvalue problems. The amplitudes governing the vectors not parallel to the Bethe states are shown to factorize in terms of elementary building blocks functions. The results for the non-compact SL(2,R) model are argued to be derived from those obtained for the compact systems by taking suitable N→∞ limits. This permits us to study the properties of the non-compact SL(2,R) model starting from systems with finite degrees of freedom.

Green roofs and the LEED green building rating system

Energy Technology Data Exchange (ETDEWEB)

Kula, R. [Sustainable Solutions Inc., Wagoner, OK (United States)

2005-07-01

The sustainable building industry is becoming increasingly aware of the host of public and private benefits that green roofs can provide in built environments. In dense urban environments, green roofs function to reduce stormwater runoff, urban heat island effects, and particulate matter (PM) pollution. The emerging green roof industry is now poised to support the efforts of green building networks in North America. This paper discussed the general benefits of green roofs, and their recognition within the Leadership in Energy and Environmental Design (LEED) Green Building Rating System. A case study of Mountain Equipment Co-op's Winnipeg site was presented. The building's green roof was directly responsible for earning 5 credits and contributing to the achievement of an additional 2 credits under the LEEDS certification process. Credits were earned for reduced site disturbance; landscape design to reduce heat islands; and water efficiency. The green roof at the site provided the vast majority of the building's cooling needs through an evaporative cooling trough. A photovoltaic pump was used to feed the building's irrigation system, as well as to pump ground water through cooling valances. It was concluded that the rise of sustainable building practices and the LEED Green Building Rating System will revolutionize the way new buildings are constructed.

Molecular Simulation of Reacting Systems; TOPICAL

International Nuclear Information System (INIS)

THOMPSON, AIDAN P.

2002-01-01

The final report for a Laboratory Directed Research and Development project entitled, Molecular Simulation of Reacting Systems is presented. It describes efforts to incorporate chemical reaction events into the LAMMPS massively parallel molecular dynamics code. This was accomplished using a scheme in which several classes of reactions are allowed to occur in a probabilistic fashion at specified times during the MD simulation. Three classes of reaction were implemented: addition, chain transfer and scission. A fully parallel implementation was achieved using a checkerboarding scheme, which avoids conflicts due to reactions occurring on neighboring processors. The observed chemical evolution is independent of the number of processors used. The code was applied to two test applications: irreversible linear polymerization and thermal degradation chemistry

Green Consumerism : an Eco-Friendly Behaviour Form Through The Green Product Consumption and Green Marketing

OpenAIRE

Handayani, Wiwik

2017-01-01

This research is referred to analyse the influence of consumer attitude of green product towards purchase intention. The consumer attitude of green product is a psychological tendencies that is expressed by evaluating a certain entity with some advantage or disadvantage considerations. The problem of this research is the low of cunsumer awareness to consume green product, because the lack to comprehend the importance of green product usage for health and eco-friendly. The purpose of this rese...

Additive Manufacturing for Cost Efficient Production of Compact Ceramic Heat Exchangers and Recuperators

Energy Technology Data Exchange (ETDEWEB)

Shulman, Holly [Ceralink Incorporated, Troy, NY (United States); Ross, Nicole [Ceralink Incorporated, Troy, NY (United States)

2015-10-30

An additive manufacture technique known as laminated object manufacturing (LOM) was used to fabricate compact ceramic heat exchanger prototypes. LOM uses precision CO2 laser cutting of ceramic green tapes, which are then precision stacked to build a 3D object with fine internal features. Modeling was used to develop prototype designs and predict the thermal response, stress, and efficiency in the ceramic heat exchangers. Build testing and materials analyses were used to provide feedback for the design selection. During this development process, laminated object manufacturing protocols were established. This included laser optimization, strategies for fine feature integrity, lamination fluid control, green handling, and firing profile. Three full size prototypes were fabricated using two different designs. One prototype was selected for performance testing. During testing, cross talk leakage prevented the application of a high pressure differential, however, the prototype was successful at withstanding the high temperature operating conditions (1300 °F). In addition, analysis showed that the bulk of the part did not have cracks or leakage issues. This led to the development of a module method for next generation LOM heat exchangers. A scale-up cost analysis showed that given a purpose built LOM system, these ceramic heat exchangers would be affordable for the applications.

Starbursts in Blue compact dwarf galaxies

International Nuclear Information System (INIS)

Thuan, T.X.

1987-01-01

We summarize all the arguments for a bursting mode of star formation in blue compact dwarf galaxies. We show in particular how spectral synthesis of far ultraviolet spectra of Blue compact dwarf galaxy constitutes a powerful way for studying the star formation history in these galaxies. Blue compact dwarf galaxy luminosity functions show jumps and discontinuities. These jumps act like fossil records of the star-forming bursts, helping us to count and date the bursts

Green power programs in Canada : 2003 : overview of Government green power policies, utility green power implementation initiatives, green power and certificate marketing programs, and their benefits

International Nuclear Information System (INIS)

Whitmore, J.; Bramley, M.; Holmes, R.

2004-09-01

Green power is defined as electricity produced from renewable sources, and whose production has low adverse impacts on the environment, human health and communities. Green power has near-zero greenhouse gas (GHG) emissions and includes sources such as wind, hydro, and solar power. It offers several environmental benefits, as well as the enhancement of energy security, regional development, economic diversification and the creation of skilled jobs. There are four categories of programs related to green power development in Canada: government green power policies, utility green power development programs, green power marketing initiatives, and green power certificate marketing initiatives. Most of the activities in Canada associated with these four categories in 2003 were discussed in this report. However, difficulties with quantification prevented the inclusion of some green power activities such as (1) the generation of green power not certified or identified by the generator as green power, (2) industry or residential self-generation, (3) net metering, and (4) small government programs. Green power generation facilities in 2003 totaled 775 MW of capacity compared to 539 MW in 2002. Hydro capacity represented 41 per cent, followed by wind capacity at 40 per cent and wood waste at 17 per cent. Most of the green power generation facilities in 2003 were located in Alberta, followed by British Columbia, Ontario and Quebec. 230 refs., 8 tabs., 1 fig

Compact magnetic fusin reactor concepts

International Nuclear Information System (INIS)

Chung, K.M.

1984-01-01

Compact, high-power-density approaches to fusion power represent alternatives to main-line fusion concepts, Tokamaks and mirrors. If technological issues are resolved, theses approaches would yield small, low-cost fusion power plants. This survey reviews the principal physics and technology employed by leading compact magnetic fusion plants. (Author)

Invariant subsets under compact quantum group actions

OpenAIRE

Huang, Huichi

2012-01-01

We investigate compact quantum group actions on unital $C^*$-algebras by analyzing invariant subsets and invariant states. In particular, we come up with the concept of compact quantum group orbits and use it to show that countable compact metrizable spaces with infinitely many points are not quantum homogeneous spaces.

Topological entropy of continuous actions of compactly generated groups

OpenAIRE

Schneider, Friedrich Martin

2015-01-01

We introduce a notion of topological entropy for continuous actions of compactly generated topological groups on compact Hausdorff spaces. It is shown that any continuous action of a compactly generated topological group on a compact Hausdorff space with vanishing topological entropy is amenable. Given an arbitrary compactly generated locally compact Hausdorff topological group $G$, we consider the canonical action of $G$ on the closed unit ball of $L^{1}(G)' \\cong L^{\\infty}(G)$ endowed with...

Green power programs in Canada : 2002 : Overview of Government green power policies, utility green power development programs, green power and certificate marketing initiatives, and their benefits

International Nuclear Information System (INIS)

Bramley, M.; Boustie, S.; Vadgama, J.; Wieler, C.; Pape-Salmon, A.; Holmes, R.

2003-11-01

Green power is generally defined as electricity produced from renewable sources, and whose production has low adverse impacts on the environment, human health and communities. Green power has near-zero greenhouse gas (GHG) emissions and includes sources such as wind, hydro, and solar power. Green power offers several environmental benefits, as well as the enhancement of energy security, regional development, economic diversification and the creation of skilled jobs. There are four categories of programs related to green power development in Canada: government green power policies, utility green power development programs, green power marketing initiatives, and green power certificate marketing initiatives. Most of the activities associated with these four categories in 2002 were discussed in this report. However, difficulties with quantification prevented the inclusion of some green power activities in the report, such as (1) the generation of green power not certified or identified by the generator as green power, (2) industry or residential self-generation, (3) net metering, and (4) small government programs. Each category was presented in detail. The information included in the report was based on surveys sent to each program proponent. Follow-up communications and other publicly available information was also included. New programs operating in 2003 or currently under development were listed. refs., 8 tabs

Mappings with closed range and compactness

International Nuclear Information System (INIS)

Iyahen, S.O.; Umweni, I.

1985-12-01

The motivation for this note is the result of E.O. Thorp that a normed linear space E is finite dimensional if and only if every continuous linear map for E into any normed linear space has a closed range. Here, a class of Hausdorff topological groups is introduced; called r-compactifiable topological groups, they include compact groups, locally compact Abelian groups and locally convex linear topological spaces. It is proved that a group in this class which is separable, complete metrizable or locally compact, is necessarily compact if its image by a continuous group homomorphism is necessarily closed. It is deduced then that a Hausdorff locally convex is zero if its image by a continuous additive map is necessarily closed. (author)

Controlled Compact High Voltage Power Lines

Directory of Open Access Journals (Sweden)

Postolati V.

2016-04-01

Full Text Available Nowadays modern overhead transmission lines (OHL constructions having several significant differences from conventional ones are being used in power grids more and more widely. Implementation of compact overhead lines equipped with FACTS devices, including phase angle regulator settings (compact controlled OHL, appears to be one of the most effective ways of power grid development. Compact controlled AC HV OHL represent a new generation of power transmission lines embodying recent advanced achievements in design solutions, including towers and insulation, together with interconnection schemes and control systems. Results of comprehensive research and development in relation to 110–500kV compact controlled power transmission lines together with theoretical basis, substantiation, and methodological approaches to their practical application are presented in the present paper.

Compact approach to fusion power reactors

International Nuclear Information System (INIS)

Hagenson, R.L.; Krakowski, R.A.; Bathke, C.G.; Miller, R.L.

1984-01-01

The potential of the Reversed-Field Pinch (RFP) for development into an efficient, compact, copper-coil fusion reactor has been quantified by comprehensive parametric tradeoff studies. These compact systems promise to be competitive in size, power density, and cost to alternative energy sources. Conceptual engineering designs that largely substantiate these promising results have since been completed. This 1000-MWe(net) design is described along with a detailed rationale and physics/technology assessment for the compact approach to fusion

The Green Experiment: Cities, Green Stormwater Infrastructure, and Sustainability

Directory of Open Access Journals (Sweden)

Christopher M. Chini

2017-01-01

Full Text Available Green infrastructure is a unique combination of economic, social, and environmental goals and benefits that requires an adaptable framework for planning, implementing, and evaluating. In this study, we propose an experimental framework for policy, implementation, and subsequent evaluation of green stormwater infrastructure within the context of sociotechnical systems and urban experimentation. Sociotechnical systems describe the interaction of complex systems with quantitative and qualitative impacts. Urban experimentation—traditionally referencing climate change programs and their impacts—is a process of evaluating city programs as if in a laboratory setting with hypotheses and evaluated results. We combine these two concepts into a singular framework creating a policy feedback cycle (PFC for green infrastructure to evaluate municipal green infrastructure plans as an experimental process within the context of a sociotechnical system. After proposing and discussing the PFC, we utilize the tool to research and evaluate the green infrastructure programs of 27 municipalities across the United States. Results indicate that green infrastructure plans should incorporate community involvement and communication, evaluation based on project motivation, and an iterative process for knowledge production. We suggest knowledge brokers as a key resource in connecting the evaluation stage of the feedback cycle to the policy phase. We identify three important needs for green infrastructure experimentation: (i a fluid definition of green infrastructure in policy; (ii maintenance and evaluation components of a green infrastructure plan; and (iii communication of the plan to the community.

Metaphysical green

OpenAIRE

Earon, Ofri

2011-01-01

“Sensation of Green is about the mental process like touching, seeing, hearing, or smelling, resulting from the immediate stimulation of landscape forms, plants, trees, wind and water. Sensation of Green triggers a feeling of scale, cheerfulness, calmness and peace. The spatial performance of Sensation of Green is created by a physical interaction between the language of space and the language of nature” The notion of Sensation of Green was developed through a previous study ‘Learning from th...

Green corridors basics

DEFF Research Database (Denmark)

Panagakos, George

2016-01-01

SuperGreen project, which aimed at advancing the green corridor concept through a benchmarking exercise involving Key Performance Indicators (KPIs). The chapter discusses the available definitions of green corridors and identifies the characteristics that distinguish a green corridor from any other...... efficient surface transportation corridor. After providing examples of green corridor projects in Europe, it focuses on the KPIs that have been proposed by various projects for monitoring the performance of a freight corridor. Emphasis is given to the SuperGreen KPIs, covering the economic, technical...

Heat transfer in large compacts of SYNROC powder

International Nuclear Information System (INIS)

Buykx, W.J.

1984-01-01

The parameters determining the time required to reach temperature uniformity in a shock heated cylindrical compact of SYNROC powder are identified as the dimensions of the compact and the thermal diffusivity of the material. The effect of shape and size of the compact are discussed, and an experimental study of the factors influencing the thermal diffusivity of compacted SYNROC powder is described

Compact NMR

Energy Technology Data Exchange (ETDEWEB)

Bluemich, Bernhard; Haber-Pohlmeier, Sabina; Zia, Wasif [RWTH Aachen Univ. (Germany). Inst. fuer Technische und Makromolekulare Chemie (ITMC)

2014-06-01

Nuclear Magnetic Resonance (NMR) spectroscopy is the most popular method for chemists to analyze molecular structures, while Magnetic Resonance Imaging (MRI) is a non-invasive diagnostic tool for medical doctors that provides high-contrast images of biological tissue. In both applications, the sample (or patient) is positioned inside a large, superconducting magnet to magnetize the atomic nuclei. Interrogating radio-frequency pulses result in frequency spectra that provide the chemist with molecular information, the medical doctor with anatomic images, and materials scientist with NMR relaxation parameters. Recent advances in magnet technology have led to a variety of small permanent magnets to allow compact and low-cost instruments. The goal of this book is to provide an introduction to the practical use of compact NMR at a level nearly as basic as the operation of a smart phone.

On compact galaxies in the UGC catalogue

International Nuclear Information System (INIS)

Kogoshvili, N.G.

1980-01-01

A problem of separation of compact galaxies in the UGC Catalogue is considered. Value of surface brightness equal to or less than 21sup(m) was used as compactness criterion from a square second of arc. 96 galaxies, which are brighter than 14sup(m)5 satisfy this criterion. Among compact galaxies discovered in the UGC Catalogue 7% are the Zwicky galaxies, 15% belong to the Markarian galaxies and 27% of galaxies are part of a galaxy list with high surface brightness. Considerable divergence in estimates of total share of compact galaxies in the B.A. Worontsov-Veljaminov Morphological Catalogue of Galaxies (MCG) and the UGC Catalogue is noted. This divergence results from systematical underestimation of visible sizes of compact galaxies in the MCG Catalogue as compared with the UGC Catalogue [ru

Rule-Based Multidisciplinary Tool for Unsteady Reacting Real-Fluid Flows, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A design and analysis computational tool is proposed for simulating unsteady reacting flows in combustor devices used in reusable launch vehicles. Key aspects...

Planar compaction of ceramic powders with mining explosives

International Nuclear Information System (INIS)

Stuivinga, M.; Verbeek, H.J.; Carton, E.P.

2000-01-01

Shock compaction experiments of B 4 C powders have been performed using a planar configuration. The powders were contained between metal plates. On top of the upper plate, having a thickness of about 10 mm, was a layer of mining explosives. For this configuration, computer simulations have been performed with use of the hydrocode Autodyn. In comparison with the cylindrical compaction process the planar compaction process appears to be quite different. The reason is the very low detonation velocity of the used mining explosives (2-4 km/s), which is much lower than the sound and shock speeds of the steel plate, in combination with the relatively large thickness of the metal layer. As a result, the nature of the compaction process of the powder initially more resembles a quasi-static compaction process than a shock compaction process. Due to the quasi-static nature of the compaction, the pressure release in the powder after compression is very gradual. Therefore, no strong rarefaction waves leading to high tensile stresses in the compact arise. Flat plates (10x10 cm, 0.6-0.8 cm thick) of Al (20-30 vol %) infiltrated B 4 C have been fabricated using this configuration

Application of nanotechnology in self-compacting concrete design

International Nuclear Information System (INIS)

Maghsoudi, A. A.; Arabpour Dahooei, F.

2009-01-01

In this study, first, different mix design of four types of Self-Compacting Concrete, 1. Self-Compacting Concrete consisted of only nano silica, 2. Self-Compacting Concrete included only micro silica, 3. Self-Compacting Concrete consisted of both micro silica and nano silica and 4. Self-Compacting Concrete without micro silica and nano silica called as control mix, were casted and tested to find out the values of the Slump Flow, L-Box and 7 and 28 days compressive strength. Then, based on the results obtained and as yet there is no universally accepted standard for characterizing of Self-Compacting Concrete, the most suitable four concrete mixes were selected for further investigation of fresh and hardened concrete. For selected mixes, the fresh concrete properties such as values of the Slump Flow, L-Box, V-Funnel, J-Ring and hardened engineering properties such as compressive and flexural strength, shrinkage and swelling values were investigated for three curing conditions at short and long term. The results showed that the engineering properties of Self-Compacting Concrete mixes could not be improved by adding only nano silica. However, a satisfactory behavior can be achieved using micro silica in the Self-Compacting Concrete mixes. However, by adding both micro silica and nano silica to the Self-Compacting Concrete mixtures, the best effect on the engineering properties was reported while comparing to the control mixes.

Double shock experiments and reactive flow modeling on LX-17 to understand the reacted equation of state

International Nuclear Information System (INIS)

Vandersall, Kevin S; Garcia, Frank; Fried, Laurence E; Tarver, Craig M

2014-01-01

Experimental data from measurements of the reacted state of an energetic material are desired to incorporate reacted states in modeling by computer codes. In a case such as LX-17 (92.5% TATB and 7.5% Kel-F by weight), where the time dependent kinetics of reaction is still not fully understood and the reacted state may evolve over time, this information becomes even more vital. Experiments were performed to measure the reacted state of LX-17 using a double shock method involving the use of two flyer materials (with known properties) mounted on the projectile that send an initial shock through the material close to or above the Chapman-Jouguet (CJ) state followed by a second shock at a higher magnitude into the detonated material. By measuring the parameters of the first and second shock waves, information on the reacted state can be obtained. The LX-17 detonation reaction zone profiles plus the arrival times and amplitudes of reflected shocks in LX-17 detonation reaction products were measured using Photonic Doppler Velocimetry (PDV) probes and an aluminum foil coated LiF window. A discussion of this work will include the experimental parameters, velocimetry profiles, data interpretation, reactive CHEETAH and Ignition and Growth modeling, as well as detail on possible future experiments.

Periodically poled self-frequency-doubling green laser fabricated from Nd:Mg:LiNbO₃ single crystal.

Science.gov (United States)

Wang, Dong Zhou; Sun, De Hui; Kang, Xue Liang; Sang, Yuan Hua; Yan, Bo Xia; Liu, Hong; Bi, Yong

2015-07-13

Although a breakthrough in the fabrication of green laser diodes has occurred, the high costs associated with the difficulty of manufacture still present a great obstacle for its practical application. Another approach for producing a green laser, by combining a laser device and a nonlinear crystal, entails the fabrication of complex structures and exhibits unstable performance due to interface contact defects, thus limiting its application. In this work, we report the fabrication by domain engineering of high quality periodically poled LiNbO₃, co-doped with Nd³⁺ and Mg²⁺, which combines a laser medium and a high efficiency second harmonic conversion crystal into a single system that is designed to overcome the above problems. An 80 mW self-frequency doubling green laser was constructed for the first time from a periodically poled Nd:Mg:LiNbO₃ crystal of 16 mm in length. This crystal can be used for developing compact, stable, highly efficient mini-solid-state-lasers, which promise to have many applications in portable laser-based spectroscopy, photo-communications, terahertz wave generation, and laser displays.

Green Chemistry Glucose Biosensor Development using Etlingera elatior Extract

Science.gov (United States)

Fatoni, A.; Anggraeni, M. D.; Zusfahair; Iqlima, H.

2018-01-01

Glucose biosensor development is one of the important strategies for early detection of diabetes mellitus disease. This study was aimed to explore the flower extract of Etlingera elatior for a green-analysis method of glucose biosensor. Flowers were extracted using ethanol: HCl and tested its performances as an indicator of glucose biosensor using glucose oxidase enzyme. The glucose oxidase react with glucose resulted hydrogen peroxide that would change the color of the flower extract. Furthermore, the extract was also studied including their stability to pH, oxidizing and reducing, temperature, and storage. The results showed that the Etlingera elatior extract had high correlation between color change and glucose concentration with regression equation of y = -0.0005x + 0.4724 and R2 of 0.9965. The studied biosensor showed a wide linear range to detect glucose sample of 0 to 500 mM. The extract characterization showed a more stable in low pH (acid), reducing agent addition, heating treatment and storage.

Solid targetry for compact cyclotrons

International Nuclear Information System (INIS)

Comor, J.

2004-01-01

In this presentation authors present experimental results of solid targetry for compact cyclotrons. It is concluded: Solid targetry is not restricted to large accelerator centers anymore; Small and medium scale radioisotope production is feasible with compact cyclotrons; The availability of versatile solid target systems is expected to boost the radiochemistry of 'exotic' positron emitters

Green Thunderstorms Observed.

Science.gov (United States)

Gallagher, Frank W., III; Beasley, William H.; Bohren, Craig F.

1996-12-01

Green thunderstorms have been observed from time to time in association with deep convection or severe weather events. Often the green coloration has been attributed to hail or to reflections of light from green foliage on the ground. Some skeptics who have not personally observed a green thunderstorm do not believe that green thunderstorms exist. They suggest that the green storms may be fabrications by excited observers. The authors have demonstrated the existence of green thunderstorms objectively using a spectrophotometer. During the spring and summer of 1995 the authors observed numerous storms and recorded hundreds of spectra of the light emanating corn these storms. It was found that the subjective judgment of colors can vary somewhat between observers, but the variation is usually in the shade of green. The authors recorded spectra of green and nongreen thunderstorms and recorded spectral measurements as a storm changed its appearance from dark blue to a bluish green. The change in color is gradual when observed from a stationary position. Also, as the light from a storm becomes greener, the luminance decreases. The authors also observed and recorded the spectrum of a thunderstorm during a period of several hours as they flew in an aircraft close to a supercell that appeared somewhat green. The authors' observations refute the ground reflection hypothesis and raise questions about explanations that require the presence of hail.

Steady state compact toroidal plasma production

Science.gov (United States)

Turner, William C.

1986-01-01

Apparatus and method for maintaining steady state compact toroidal plasmas. A compact toroidal plasma is formed by a magnetized coaxial plasma gun and held in close proximity to the gun electrodes by applied magnetic fields or magnetic fields produced by image currents in conducting walls. Voltage supply means maintains a constant potential across the electrodes producing an increasing magnetic helicity which drives the plasma away from a minimum energy state. The plasma globally relaxes to a new minimum energy state, conserving helicity according to Taylor's relaxation hypothesis, and injecting net helicity into the core of the compact toroidal plasma. Controlling the voltage so as to inject net helicity at a predetermined rate based on dissipative processes maintains or increases the compact toroidal plasma in a time averaged steady state mode.

Where are compact groups in the local Universe?

Science.gov (United States)

Díaz-Giménez, Eugenia; Zandivarez, Ariel

2015-06-01

Aims: The purpose of this work is to perform a statistical analysis of the location of compact groups in the Universe from observational and semi-analytical points of view. Methods: We used the velocity-filtered compact group sample extracted from the Two Micron All Sky Survey for our analysis. We also used a new sample of galaxy groups identified in the 2M++ galaxy redshift catalogue as tracers of the large-scale structure. We defined a procedure to search in redshift space for compact groups that can be considered embedded in other overdense systems and applied this criterion to several possible combinations of different compact and galaxy group subsamples. We also performed similar analyses for simulated compact and galaxy groups identified in a 2M++ mock galaxy catalogue constructed from the Millennium Run Simulation I plus a semi-analytical model of galaxy formation. Results: We observed that only ~27% of the compact groups can be considered to be embedded in larger overdense systems, that is, most of the compact groups are more likely to be isolated systems. The embedded compact groups show statistically smaller sizes and brighter surface brightnesses than non-embedded systems. No evidence was found that embedded compact groups are more likely to inhabit galaxy groups with a given virial mass or with a particular dynamical state. We found very similar results when the analysis was performed using mock compact and galaxy groups. Based on the semi-analytical studies, we predict that 70% of the embedded compact groups probably are 3D physically dense systems. Finally, real space information allowed us to reveal the bimodal behaviour of the distribution of 3D minimum distances between compact and galaxy groups. Conclusions: The location of compact groups should be carefully taken into account when comparing properties of galaxies in environments that are a priori different. Appendices are available in electronic form at http://www.aanda.orgFull Tables B.1 and B.2

Numerical simulation of low Mach number reacting flows

International Nuclear Information System (INIS)

Bell, J B; Aspden, A J; Day, M S; Lijewski, M J

2007-01-01

Using examples from active research areas in combustion and astrophysics, we demonstrate a computationally efficient numerical approach for simulating multiscale low Mach number reacting flows. The method enables simulations that incorporate an unprecedented range of temporal and spatial scales, while at the same time, allows an extremely high degree of reaction fidelity. Sample applications demonstrate the efficiency of the approach with respect to a traditional time-explicit integration method, and the utility of the methodology for studying the interaction of turbulence with terrestrial and astrophysical flame structures

77 FR 22805 - Meeting of the Compact Council for the National Crime Prevention and Privacy Compact; Correction

Science.gov (United States)

2012-04-17

... Compact Council (Council) created by the National Crime Prevention and Privacy Compact Act of 1998..., correct the hotel address line in ADDRESSES to read: 300 East Travis. Dated: April 10, 2012. Gary S...

The Influence of Green Marketing on Green Satisfaction Mediated By Perceived Quality and Its Impact to Green Trust in Injection Motorcycle

Directory of Open Access Journals (Sweden)

Shelvy Kurniawan

2014-09-01

Full Text Available Currently, motorcycle manufacturers are increasingly motivated to replace their motorcycle into fuel injection products. The growing concern from the consumers to the environment and the regulations of emission standards, that is Euro 3, for motorcycle industry is being finalized in the Ministry of Environment in order to be implemented in Indonesia. Through this research, the writer will examine the effect of green marketing on perceived quality, green satisfaction, and green trust, the effect of perceived quality on green satisfaction, and the effect of green satisfaction on green trust. Those effects needs to be investigated in order to know how far the effects of green marketing and to ensure whether green marketing is well accepted or not by the market in motorcycle industry. Scope of this research is also limited to the user of fuel injection motorcycle in Jakarta for Honda and Yamaha who involved as decision maker when the motorcycle is purchased. Sampling technique used in this research is quota sampling and the analysis method is structural equation modeling (SEM. The findings of this research are: green marketing has a significant direct effect on perceived quality, perceived quality has a significant direct effect on green satisfaction, green satisfaction has a significant direct effect on green trust, green marketing has a significant direct and indirect effect on green satisfaction, and green marketing has a significant direct and indirect effect on green trust. All of those effects are found to be positive effects.

REAC/TS Radiation Accident Registry: An Overview

Energy Technology Data Exchange (ETDEWEB)

Doran M. Christensen, DO, REAC/TS Associate Director and Staff Physician Becky Murdock, REAC/TS Registry and Health Physics Technician

2012-12-12

Over the past four years, REAC/TS has presented a number of case reports from its Radiation Accident Registry. Victims of radiological or nuclear incidents must meet certain dose criteria for an incident to be categorized as an “accident” and be included in the registry. Although the greatest numbers of “accidents” in the United States that have been entered into the registry involve radiation devices, the greater percentage of serious accidents have involved sealed sources of one kind or another. But if one looks at the kinds of accident scenarios that have resulted in extreme consequence, i.e., death, the greater share of deaths has occurred in medical settings.

A compact spin-exchange optical pumping system for 3He polarization based on a solenoid coil, a VBG laser diode, and a cosine theta RF coil

Science.gov (United States)

Lee, Sungman; Kim, Jongyul; Moon, Myung Kook; Lee, Kye Hong; Lee, Seung Wook; Ino, Takashi; Skoy, Vadim R.; Lee, Manwoo; Kim, Guinyun

2013-02-01

For use as a neutron spin polarizer or analyzer in the neutron beam lines of the HANARO (High-flux Advanced Neutron Application ReactOr) nuclear research reactor, a 3He polarizer was designed based on both a compact solenoid coil and a VBG (volume Bragg grating) diode laser with a narrow spectral linewidth of 25 GHz. The nuclear magnetic resonance (NMR) signal was measured and analyzed using both a built-in cosine radio-frequency (RF) coil and a pick-up coil. Using a neutron transmission measurement, we estimated the polarization ratio of the 3He cell as 18% for an optical pumping time of 8 hours.

Purchasing green to become greener: Factors influence consumers’ green purchasing behavior

Directory of Open Access Journals (Sweden)

Hosein Vazifehdoust

2013-09-01

Full Text Available This study proposes an integrated model that combines the Theory of Reasoned Action (TRA and two categories of variables, personal and marketing, to investigate the attitudinal and behavioral decision factors to purchase green products. The model derived and tested via structural equation modeling on a sample of 374 consumers from the Guilan province in Iran. The results show that attitude is explained by consumers’ environmental concern, quality of green products, green advertising and green labeling. The results of the structural equation analysis indicate that attitude positively influences intention to purchase green products. Green purchasing intention also influences on green purchasing behavior. This paper also discusses the implications of the results for marketers and researchers.

Machine for compacting solid residues

International Nuclear Information System (INIS)

Herzog, J.

1981-11-01

Machine for compacting solid residues, particularly bulky radioactive residues, constituted of a horizontally actuated punch and a fixed compression anvil, in which the residues are first compacted horizontally and then vertically. Its salient characteristic is that the punch and the compression anvil have embossments on the compression side and interpenetrating plates in the compression position [fr

Soil compaction and fertilization in soybean productivity

Directory of Open Access Journals (Sweden)

Beutler Amauri Nelson

2004-01-01

Full Text Available Soil compaction and fertilization affect soybean development. This study evaluated the effects of soil compaction and fertilization on soybean (Glycine max cv. Embrapa 48 productivity in a Typic Haplustox under field conditions in Jaboticabal, SP, Brazil. A completely randomized design with a 5 x 2 factorial layout (compaction vs. fertilization, with four replications in each treatment, was employed. Each experimental unit (replicate consisted of a 3.6 m² useful area. After the soil was prepared by cultivation, an 11 Mg tractor passed over it a variable number of times to create five levels of compaction. Treatments were: T0= no compaction, T1= one tractor pass, T2= two, T4= four, and T6= six passes, and no fertilizer and fertilizer to give soybean yields of 2.5 to 2.9 Mg ha-1. Soil was sampled at depths of 0.02-0.05, 0.07-0.10, and 0.15-0.18 m to determine macro and microporosity, penetration resistance (PR, and bulk density (Db. After 120 days growing under these conditions, the plants were analyzed in terms of development (plant height, number of pods, shoot dry matter per plant and weight of 100 seeds and seed productivity per hectare. Soil compaction decreased soybean development and productivity, but this effect was decreased by soil fertilization, showing that such fertilization increased soybean tolerance to soil compaction.

Is 'green finance' actually green? 'Make The Planet Great Again' or 'Green-washing', we must choose. Report on green bonds and climate bonds

International Nuclear Information System (INIS)

Combes, Maxime; Plihon, Dominique; Zippert, Jean-Sebastien; Chaussalet, Alexis; Planche, Jeanne; Poulain, Melanie

2017-12-01

As Paris dreams of becoming the capital of green finance, the author proposes a discussion of the emerging market of green bonds, and formulates a set of recommendations for this new financial instrument not to be polluted by green-washing operations. He first describes what a green bond is, and then comments what the green bond market represents, discusses development perspectives for this market, comments the Paris dream of becoming the world capital of a green and sustainable finance. He explains why this green bond market appears to be so interesting, and what guarantees that a green bond will finance green projects. He discusses the role of rating agencies, whether the emitter of a green bond must be green, and the impact of green bonds on climate, on the environment and on populations. He discusses the possible evolution towards a constraining regulation, and examines whether this system can be an operational financing source for energy transition. Recommendations concern the market regulation by public authorities, the creation of a new rating agency for green finance, how to make the world bond market climate-compatible, and the creation of other financing channels for actors who have no access to the bond market

Aligning laboratory and field compaction practices for asphalt - the influence of compaction temperature on mechanical properties

NARCIS (Netherlands)

Bijleveld, Frank; Miller, Seirgei Rosario; de Bondt, A.H.; Doree, Andries G.

2015-01-01

The approach used to identify a compaction temperature in the laboratory, based on binder viscosity, provides a single compaction temperature whereas, on-site, a roller operates within a temperature window. The effect on the density and mechanical properties of rolling during a temperature window

Green industrial policy

OpenAIRE

Dani Rodrik

2014-01-01

Green growth requires green technologies: production techniques that economize on exhaustible resources and emit fewer greenhouse gases. The availability of green technologies both lowers social costs in the transition to a green growth path and helps achieve a satisfactory rate of material progress under that path. The theoretical case in favour of using industrial policy to facilitate green growth is quite strong. Economists’ traditional scepticism on industrial policy is grounded instead o...

Roller compaction of moist pharmaceutical powders.

Science.gov (United States)

Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

2010-05-31

The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Bone compaction enhances fixation of weightbearing titanium implants

DEFF Research Database (Denmark)

Kold, Søren; Rahbek, Ole; Vestermark, Marianne

2005-01-01

are weightbearing, the effects of compaction on weightbearing implants were examined. The hypothesis was that compaction would increase implant fixation compared with conventional drilling. Porous-coated titanium implants were inserted bilaterally into the weightbearing portion of the femoral condyles of dogs....... In each dog, one knee had the implant cavity prepared with drilling, and the other knee was prepared with compaction. Eight dogs were euthanized after 2 weeks, and eight dogs were euthanized after 4 weeks. Femoral condyles from an additional eight dogs represented Time 0. Compacted specimens had higher...... bone-implant contact and periimplant bone density at 0 and 2 weeks, but not at 4 weeks. A biphasic response of compaction was found with a pushout test, as compaction increased ultimate shear strength and energy absorption at 0 and 4 weeks, but not at 2 weeks. This biphasic response indicates...

Gamma-Rays from Galactic Compact Sources

Science.gov (United States)

Kaaret, Philip

2007-04-01

Recent discoveries have revealed many sources of TeV photons in our Mikly Way galaxy powered by compact objects, either neutron stars or black holes. These objects must be powerful particle accelerators, some with peak energies of at least 100 TeV, and may be neutrino, as well as photon, sources. Future TeV observations will enable us to address key questions concerning particle acceleration by compact objects including the fraction of energy which accreting black holes channel into relativstic jet production, whether the compact object jets are leptonic or hadronic, and the mechanism by which pulsar winds accelerate relativistic particles. We report on work done related to compact Galactic objects in preparation of a White Paper on the status and future of ground-based gamma-ray astronomy requested by the Division of Astrophysics of the American Physical Society.

Green consumerism

DEFF Research Database (Denmark)

de Groot, Judith I.M.; Schuitema, Geertje; Garson, Carrie Lee

and biospheric values influence the importance of such ‘green’ product characteristics on purchasing intentions. In two within-subjects full-factorial experimental studies (N = 100 and N = 107), we found that purchase intentions of products were only steered by green characteristics if prices were low...... and the brand was familiar. Green product characteristics did not influence purchase intentions at all when these proself product characteristics were not fulfilled (i.e., high prices and unfamiliar brands). The importance of proself and green product characteristics on purchasing intentions was also......Our presentation will focus on the influence of product characteristics and values on green consumerism. Although generally a majority of consumers support the idea of purchasing green products, we argue, based on social dilemma theory, that proself product characteristics and egoistic...

Correlating particle hardness with powder compaction performance.

Science.gov (United States)

Cao, Xiaoping; Morganti, Mikayla; Hancock, Bruno C; Masterson, Victoria M

2010-10-01

Assessing particle mechanical properties of pharmaceutical materials quickly and with little material can be very important to early stages of pharmaceutical research. In this study, a wide range of pharmaceutical materials were studied using atomic force microscopy (AFM) nanoindentation. A significant amount of particle hardness and elastic modulus data were provided. Moreover, powder compact mechanical properties of these materials were investigated in order to build correlation between the particle hardness and powder compaction performance. It was found that the materials with very low or high particle hardness most likely exhibit poor compaction performance while the materials with medium particle hardness usually have good compaction behavior. Additionally, the results from this study enriched Hiestand's special case concept on particle hardness and powder compaction performance. This study suggests that the use of AFM nanoindentation can help to screen mechanical properties of pharmaceutical materials at early development stages of pharmaceutical research.

Compacting biomass waste materials for use as fuel

Science.gov (United States)

Zhang, Ou

Every year, biomass waste materials are produced in large quantity. The combustibles in biomass waste materials make up over 70% of the total waste. How to utilize these waste materials is important to the nation and the world. The purpose of this study is to test optimum processes and conditions of compacting a number of biomass waste materials to form a densified solid fuel for use at coal-fired power plants or ordinary commercial furnaces. Successful use of such fuel as a substitute for or in cofiring with coal not only solves a solid waste disposal problem but also reduces the release of some gases from burning coal which cause health problem, acid rain and global warming. The unique punch-and-die process developed at the Capsule Pipeline Research Center, University of Missouri-Columbia was used for compacting the solid wastes, including waste paper, plastics (both film and hard products), textiles, leaves, and wood. The compaction was performed to produce strong compacts (biomass logs) under room temperature without binder and without preheating. The compaction conditions important to the commercial production of densified biomass fuel logs, including compaction pressure, pressure holding time, back pressure, moisture content, particle size, binder effects, and mold conditions were studied and optimized. The properties of the biomass logs were evaluated in terms of physical, mechanical, and combustion characteristics. It was found that the compaction pressure and the initial moisture content of the biomass material play critical roles in producing high-quality biomass logs. Under optimized compaction conditions, biomass waste materials can be compacted into high-quality logs with a density of 0.8 to 1.2 g/cm3. The logs made from the combustible wastes have a heating value in the range 6,000 to 8,000 Btu/lb which is only slightly (10 to 30%) less than that of subbituminous coal. To evaluate the feasibility of cofiring biomass logs with coal, burn tests were

Self-Compacting Concrete in Precast Elements Industry

Directory of Open Access Journals (Sweden)

Corneliu Bob

2005-01-01

Full Text Available In this paper the authors present information about the Self-Compacting Concrete and experimental results regarding the use of them into precast element industry. This type of concrete does not require vibration for placing and compaction; it is able to flow under its own weight, completely filling formwork and achieving full compaction, even in the presence of congested reinforcement. The experimental programme has take into account two prestressed beams which were prefabricated and tested on a special stands. The beams of Self-Compacting Concrete with the length of 24 m were prepared at „Beton-Star” Kft, Kecsekenet, Hungary, and used at the CASCO, Satu-Mare.

Compact instrument for fluorescence image-guided surgery

Science.gov (United States)

Wang, Xinghua; Bhaumik, Srabani; Li, Qing; Staudinger, V. Paul; Yazdanfar, Siavash

2010-03-01

Fluorescence image-guided surgery (FIGS) is an emerging technique in oncology, neurology, and cardiology. To adapt intraoperative imaging for various surgical applications, increasingly flexible and compact FIGS instruments are necessary. We present a compact, portable FIGS system and demonstrate its use in cardiovascular mapping in a preclinical model of myocardial ischemia. Our system uses fiber optic delivery of laser diode excitation, custom optics with high collection efficiency, and compact consumer-grade cameras as a low-cost and compact alternative to open surgical FIGS systems. Dramatic size and weight reduction increases flexibility and access, and allows for handheld use or unobtrusive positioning over the surgical field.

A Compact Mobile Ozone Lidar for Atmospheric Ozone and Aerosol Profiling

Science.gov (United States)

De Young, Russell; Carrion, William; Pliutau, Denis

2014-01-01

A compact mobile differential absorption lidar (DIAL) system has been developed at NASA Langley Research Center to provide ozone, aerosol and cloud atmospheric measurements in a mobile trailer for ground-based atmospheric ozone air quality campaigns. This lidar is integrated into the Tropospheric Ozone Lidar Network (TOLNet) currently made up of four other ozone lidars across the country. The lidar system consists of a UV and green laser transmitter, a telescope and an optical signal receiver with associated Licel photon counting and analog channels. The laser transmitter consist of a Q-switched Nd:YLF inter-cavity doubled laser pumping a Ce:LiCAF tunable UV laser with all the associated power and lidar control support units on a single system rack. The system has been configured to enable mobile operation from a trailer and was deployed to Denver, CO July 15-August 15, 2014 supporting the DISCOVER-AQ campaign. Ozone curtain plots and the resulting science are presented.

Effect of slash on forwarder soil compaction

Science.gov (United States)

Timothy P. McDonald; Fernando Seixas

1997-01-01

A study of the effect of slash on forwarder soil compaction was carried out. The level of soil compaction at two soil moisture contents, three slash densities (0, 10, and 20 kg/m2), and two levels of traffic (one and five passes) were measured. Results indicated that, on dry, loamy sand soils, the presence of slash did not decrease soil compaction after one forwarder...

Green Power Partnership 100 Green Power Users

Science.gov (United States)

EPA's Green Power Partnership is a voluntary program designed to reduce the environmental impact of electricity generation by promoting renewable energy. Partners on this list use green power to meet 100 of their U.S. organization-wide electricity use.

Compacted cancellous bone has a spring-back effect

DEFF Research Database (Denmark)

Kold, S; Bechtold, JE; Ding, Ming

2003-01-01

A new surgical technique, compaction, has been shown to improve implant fixation. It has been speculated that the enhanced implant fixation with compaction could be due to a spring-back effect of compacted bone. However, such an effect has yet to be shown. Therefore we investigated in a canine mo....... Thus we found a spring-back effect of compacted bone, which may be important for increasing implant fixation by reducing initial gaps between the implant and bone....

Effect of repeated compaction of tablets on tablet properties and work of compaction using an instrumented laboratory tablet press.

Science.gov (United States)

Gamlen, Michael John Desmond; Martini, Luigi G; Al Obaidy, Kais G

2015-01-01

The repeated compaction of Avicel PH101, dicalcium phosphate dihydrate (DCP) powder, 50:50 DCP/Avicel PH101 and Starch 1500 was studied using an instrumented laboratory tablet press which measures upper punch force, punch displacement and ejection force and operates using a V-shaped compression profile. The measurement of work compaction was demonstrated, and the test materials were ranked in order of compaction behaviour Avicel PH101 > DCP/Avicel PH101 > Starch > DCP. The behaviour of the DCP/Avicel PH101 mixture was distinctly non-linear compared with the pure components. Repeated compaction and precompression had no effect on the tensile fracture strength of Avicel PH101 tablets, although small effects on friability and disintegration time were seen. Repeated compaction and precompression reduced the tensile strength and the increased disintegration time of the DCP tablets, but improved the strength and friability of Starch 1500 tablets. Based on the data reported, routine laboratory measurement of tablet work of compaction may have potential as a critical quality attribute of a powder blend for compression. The instrumented press was suitable for student use with minimal supervisor input.

Green Roofs: Standardization and Quality Control of Processes in Green Construction

Directory of Open Access Journals (Sweden)

Korol Elena

2017-01-01

Full Text Available The article considers the problems of standardization and quality control of processes in the construction, improvement of integrated safety of buildings and the implementation of innovative green building technologies, the use of national standards as well as international rating systems for green buildings evaluation. This is one of the priority directions in development of the modern construction. The aim of this study is the analysis of the green roof systems and international standards, which were carried out in the green building industry. The authors have studied traditional and innovative solutions of rational using natural resources and energy, the green roof system with integration of supported solar and wind energy collecting and converting devices and of irrigation system. Some studies provide evidence for the benefits of the modular green roof system in urban green space with microclimate differences. This article presents a new research which advances our knowledge of the economic and environmental services provided by the green roof system. Research reported here also considers the analysis of the Russian and international legislation of the quality control of processes in green construction.

The synergy in green persuasion: Green celebrity endorsers in green advertising: A study of brand-endorser congruence effects in green advertising

OpenAIRE

Blasche, J.; Ketelaar, P.E.

2015-01-01

This study examines celebrity endorser-brand congruence effects in green advertising on the ads' effectiveness. In an experimental survey, Dutch participants (197) saw ads with a congruent or incongruent celebrity endorser. Extending the match-up hypothesis to a novel match-up factor, greenness, the results show that pro-environmental celebrity endorsers yield more favourable attitudes towards the ad, the brand, and purchase intentions compared to non-green celebrity endorsers. Practitioners ...

Quantitative imaging of turbulent and reacting flows

Energy Technology Data Exchange (ETDEWEB)

Paul, P.H. [Sandia National Laboratories, Livermore, CA (United States)

1993-12-01

Quantitative digital imaging, using planar laser light scattering techniques is being developed for the analysis of turbulent and reacting flows. Quantitative image data, implying both a direct relation to flowfield variables as well as sufficient signal and spatial dynamic range, can be readily processed to yield two-dimensional distributions of flowfield scalars and in turn two-dimensional images of gradients and turbulence scales. Much of the development of imaging techniques to date has concentrated on understanding the requisite molecular spectroscopy and collision dynamics to be able to determine how flowfield variable information is encoded into the measured signal. From this standpoint the image is seen as a collection of single point measurements. The present effort aims at realizing necessary improvements in signal and spatial dynamic range, signal-to-noise ratio and spatial resolution in the imaging system as well as developing excitation/detection strategies which provide for a quantitative measure of particular flowfield scalars. The standard camera used for the study is an intensified CCD array operated in a conventional video format. The design of the system was based on detailed modeling of signal and image transfer properties of fast UV imaging lenses, image intensifiers and CCD detector arrays. While this system is suitable for direct scalar imaging, derived quantities (e.g. temperature or velocity images) require an exceptionally wide dynamic range imaging detector. To apply these diagnostics to reacting flows also requires a very fast shuttered camera. The authors have developed and successfully tested a new type of gated low-light level detector. This system relies on fast switching of proximity focused image-diode which is direct fiber-optic coupled to a cooled CCD array. Tests on this new detector show significant improvements in detection limit, dynamic range and spatial resolution as compared to microchannel plate intensified arrays.

Compact Antenna Range

Data.gov (United States)

Federal Laboratory Consortium — Facility consists of a folded compact antenna range including a computer controlled three axis position table, parabolic reflector and RF sources for the measurement...

Linear Shrinkage Behaviour of Compacted Loam Masonry Blocks

Directory of Open Access Journals (Sweden)

NAWAB ALI LAKHO

2017-04-01

Full Text Available Walls of wet loam, used in earthen houses, generally experience more shrinkage which results in cracks and less compressive strength. This paper presents a technique of producing loam masonry blocks that are compacted in drained state during casting process in order to minimize shrinkage. For this purpose, loam masonry blocks were cast and compacted at a pressure of 6 MPa and then dried in shade by covering them in plastic sheet. The results show that linear shrinkage of 2% occurred which is smaller when compared to un-compacted wet loam walls. This implies that the loam masonry blocks compacted in drained state is expected to perform better than un-compacted wet loam walls.

Formation of a compact toroid for enhanced efficiency

Energy Technology Data Exchange (ETDEWEB)

Mozgovoy, A. G. [P.N. Lebedev Physical Institute, Moscow 119991 (Russian Federation); Romadanov, I. V.; Ryzhkov, S. V., E-mail: ryzhkov@power.bmstu.ru [Bauman Moscow State Technical University, Moscow 105005 (Russian Federation)

2014-02-15

We report here our results on the formation of a plasma configuration with the generic name of compact toroid (CT). A method of compact toroid formation to confine, heat and compress a plasma is investigated. Formation of a compact torus using an additional toroidal magnetic field helps to increase the plasma current to a maintainable level of the original magnetic field. We design the Compact Toroid Challenge (CTC) experiment in order to improve the magnetic flux trapping during field reversal in the formation of a compact toroid. The level of the magnetic field immersed in the plasma about 70% of the primary field is achieved. The CTC device and scheme of high level capturing of magnetic flux are presented.

Green lights

DEFF Research Database (Denmark)

Fisker, Peter Kielberg

This study investigates the effect of drought on economic activity globally using remote sensing data. In particular, predicted variation in greenness is correlated with changes in the density of artificial light observed at night on a grid of 0.25 degree latitude-longitude pixels. I define drought...... as greenness estimated by lagged variation in monthly rainfall and temperature. This definition of drought performs well in identifying self-reported drought events since 2000 compared with measures of drought that do not take greenness into account, and the subsequent analysis indicates that predicted...... variation in greenness is positively associated with year-on-year changes in luminosity: If a unit of observation experiences a predicted variation in greenness that lies 1 standard deviation below the global mean, on average 1.5 - 2.5 light pixels out of 900 are extinguished that year. Finally, an attempt...

Compactness in quasi-Banach function spaces and applications to compact embeddings of Besov-type spaces

Czech Academy of Sciences Publication Activity Database

Caetano, A.M.; Gogatishvili, Amiran; Opic, B.

2016-01-01

Roč. 146, č. 5 (2016), s. 905-927 ISSN 0308-2105 R&D Projects: GA ČR GA13-14743S Institutional support: RVO:67985840 Keywords : quasi-Banach function space * compactness * compact embedding Subject RIV: BA - General Mathematics Impact factor: 1.158, year: 2016 http:// journals .cambridge.org/action/displayAbstract?fromPage=online&aid=10379393&fileId=S0308210515000761

Compaction of amorphous iron–boron powder

DEFF Research Database (Denmark)

Hendriksen, Peter Vang; Mørup, Steen; Koch, Christian

1993-01-01

Large scale practical use of bulk amorphous alloys requires the capability of molding the material to a desired design, for instance by compaction of an amorphous powder. This is a difficult task because the sintering temperature is limited by the crystallization temperature of the alloy.1 Here we......, should facilitate a compaction. The passivation layer, however, impedes a compaction. Isostatic pressing at 540 K at a pressure of 200 MPa clearly illustrated this; pellets pressed from passivated powder were much more brittle than pellets pressed from unpassivated powder. The density of the pellets...... was very low ([approximately-equal-to]25% of the density of bulk FeB). We have designed a die for uniaxial pressing in which the compaction can be performed without exposing the powder to air and have obtained densities larger than 60% of that of bulk FeB. We have reported studies of the dependence...

Green Chemistry Metrics with Special Reference to Green Analytical Chemistry

Directory of Open Access Journals (Sweden)

Marek Tobiszewski

2015-06-01

Full Text Available The concept of green chemistry is widely recognized in chemical laboratories. To properly measure an environmental impact of chemical processes, dedicated assessment tools are required. This paper summarizes the current state of knowledge in the field of development of green chemistry and green analytical chemistry metrics. The diverse methods used for evaluation of the greenness of organic synthesis, such as eco-footprint, E-Factor, EATOS, and Eco-Scale are described. Both the well-established and recently developed green analytical chemistry metrics, including NEMI labeling and analytical Eco-scale, are presented. Additionally, this paper focuses on the possibility of the use of multivariate statistics in evaluation of environmental impact of analytical procedures. All the above metrics are compared and discussed in terms of their advantages and disadvantages. The current needs and future perspectives in green chemistry metrics are also discussed.

Green Chemistry Metrics with Special Reference to Green Analytical Chemistry.

Science.gov (United States)

Tobiszewski, Marek; Marć, Mariusz; Gałuszka, Agnieszka; Namieśnik, Jacek

2015-06-12

The concept of green chemistry is widely recognized in chemical laboratories. To properly measure an environmental impact of chemical processes, dedicated assessment tools are required. This paper summarizes the current state of knowledge in the field of development of green chemistry and green analytical chemistry metrics. The diverse methods used for evaluation of the greenness of organic synthesis, such as eco-footprint, E-Factor, EATOS, and Eco-Scale are described. Both the well-established and recently developed green analytical chemistry metrics, including NEMI labeling and analytical Eco-scale, are presented. Additionally, this paper focuses on the possibility of the use of multivariate statistics in evaluation of environmental impact of analytical procedures. All the above metrics are compared and discussed in terms of their advantages and disadvantages. The current needs and future perspectives in green chemistry metrics are also discussed.

Isometric coactions of compact quantum groups on compact ...

Indian Academy of Sciences (India)

a compact quantum metric space in the framework of Rieffel, where the ... This problem can be formulated and studied in various settings. ... The spaces we are interested in this paper are metric spaces, both classical and quantum. ... He has given a definition for a quantum symmetry of a classical ...... by the construction of I.

Generation of 3.5 W of diffraction-limited green light from SHG of a single tapered diode laser in a cascade of nonlinear crystals

DEFF Research Database (Denmark)

Hansen, Anders Kragh; Jensen, Ole Bjarlin; Sumpf, Bernd

2014-01-01

Many applications, e.g., within biomedicine stand to benefit greatly from the development of diode laser-based multi- Watt efficient compact green laser sources. The low power of existing diode lasers in the green area (about 100 mW) means that the most promising approach remains nonlinear...... frequency conversion of infrared tapered diode lasers. Here, we describe the generation of 3.5 W of diffraction-limited green light from SHG of a single tapered diode laser, itself yielding 10 W at 1063 nm. This SHG is performed in single pass through a cascade of two PPMgO:LN crystals with re...... power of 3.5 W corresponds to a power enhancement greater than 2 compared to SHG in each of the crystals individually and is the highest visible output power generated by frequency conversion of a single diode laser. Such laser sources provide the necessary pump power for biophotonics applications...

Preliminary evaluation of different green payments in the handling of the nitrogen nutrition of the tomato by means of the Isotope 15 n

International Nuclear Information System (INIS)

Monederos, Milagros; Duennas, Graciela; Alfonso, C.A.; Hernandez, Marcela; Almeida, Grisel

1999-01-01

With the objective of evaluating in a preliminary way the effect of some leguminous ones (Leucaena, Canavalia, Crotalaria and Mucuna) used as green payments in the handling of the tomato nutrition its later validation under field conditions was carried out a rehearsal under controlled conditions and on a red ferralitic soils compact. I it determined the derived nitrogen of each source by means of the isotope 15N

Green Chemistry Metrics with Special Reference to Green Analytical Chemistry

OpenAIRE

Marek Tobiszewski; Mariusz Marć; Agnieszka Gałuszka; Jacek Namieśnik

2015-01-01

The concept of green chemistry is widely recognized in chemical laboratories. To properly measure an environmental impact of chemical processes, dedicated assessment tools are required. This paper summarizes the current state of knowledge in the field of development of green chemistry and green analytical chemistry metrics. The diverse methods used for evaluation of the greenness of organic synthesis, such as eco-footprint, E-Factor, EATOS, and Eco-Scale are described. Both the well-establis...

Development of dispersion-strengthened XD (trademark) Cu alloys for high heat-flux applications

Science.gov (United States)

Kumar, K. Sharvan

1993-01-01

In a previous effort sponsored by NASA LeRC, the XD(trademark) process was used to produce ZrB2 particulate reinforcements in Cu and the resulting extruded material was microstructurally characterized and evaluated in tension over a range of temperatures. A problem that was encountered in that study was microstructural inhomogeneity resulting from the frequent presence of 'ZrB2 agglomerates' that were several microns in size. The presence of these agglomerates was attributed to improper mixing of powders in the green compact used in the XD process for elemental boron powder segregation. In this program, several milling parameters were examined in an effort to optimize this processing step; two levels of ZrB2 reinforcements were considered (7 vol. percent and 15 vol. percent). Microstructures of the reacted powder mass were examined to verify the absence of these agglomerates. Larger bathes of powder were then mixed, reacted, machined to size, canned, and extruded. The microstructure and tensile properties of these extrusions were examined, and the measured properties were correlated with the observed microstructure. Large unreacted or partially reacted Zr particles were present. These particles affected the mechanical properties deleteriously, and their presence is attributed to insufficient heat of reaction during XD synthesis. Alternate processing routes are recommended.

An Active Black Hole in a Compact Dwarf

Science.gov (United States)

Kohler, Susanna

2016-05-01

A new type of galaxy has just been added to the galaxy zoo: a small, compact, and old elliptical galaxy that shows signs of a monster black hole actively accreting material in its center. What can this unusual discovery tell us about how compact elliptical galaxies form?A New Galactic BeastCompact elliptical galaxies are an extremely rare early-type dwarf galaxy. Consistent with their name, compact ellipticals are small, very compact collections of ancient stars; these galaxies exhibit a high surface brightness and arent actively forming stars.Optical view of the ancient compact elliptical galaxy SDSS J085431.18+173730.5 (center of image) in an SDSS color composite image. [Adapted from Paudel et al. 2016]Most compact ellipticals are found in dense environments, particularly around massive galaxies. This has led astronomers to believe that compact ellipticals might form via the tidal stripping of a once-large galaxy in interactions with another, massive galaxy. In this model, once the original galaxys outer layers are stripped away, the compact inner bulge component would be left behind as a compact elliptical galaxy. Recent discoveries of a few isolated compact ellipticals, however, have strained this model.Now a new galaxy has been found to confuse our classification schemes: the first-ever compact elliptical to also display signs of an active galactic nucleus. Led by Sanjaya Paudel (Korea Astronomy and Space Science Institute), a team of scientists discovered SDSS J085431.18+173730.5 serendipitously in Sloan Digital Sky Survey data. The team used SDSS images and spectroscopy in combination with data from the Canada-France-Hawaii Telescope to learn more about this unique galaxy.Puzzling CharacteristicsSDSS J085431.18+173730.5 presents an interesting conundrum. Ancient compact ellipticals are supposed to be devoid of gas, with no fuel left to trigger nuclear activity. Yet SDSS J085431.18+173730.5 clearly shows the emission lines that indicate active accretion onto

Temperature evolution during compaction of pharmaceutical powders.

Science.gov (United States)

Zavaliangos, Antonios; Galen, Steve; Cunningham, John; Winstead, Denita

2008-08-01

A numerical approach to the prediction of temperature evolution in tablet compaction is presented here. It is based on a coupled thermomechanical finite element analysis and a calibrated Drucker-Prager Cap model. This approach is capable of predicting transient temperatures during compaction, which cannot be assessed by experimental techniques due to inherent test limitations. Model predictions are validated with infrared (IR) temperature measurements of the top tablet surface after ejection and match well with experiments. The dependence of temperature fields on speed and degree of compaction are naturally captured. The estimated transient temperatures are maximum at the end of compaction at the center of the tablet and close to the die wall next to the powder/die interface.

'Crescent'-shaped tokamak for compact ignition

International Nuclear Information System (INIS)

Yamazaki, K.; Reiersen, W.T.

1985-12-01

A compact high-beta tokamak configuration with ''crescent''-shaped (or ''boomerang''-shaped) cross-section is proposed as a next-generation ignition machine. This configuration with a small indentation but a large triangularity is more compact than the normal dee-shaped design because of its high-beta characteristics in the first-second transition regime of stability. This may also be a more reliable next-generation compact device than the bean-shaped design with large indentation and small triangularity, because this design dose not rely on the second stability and is easily extendable from the present dee-shaped design. (author)

Generalised model for anisotropic compact stars

Energy Technology Data Exchange (ETDEWEB)

Maurya, S.K. [University of Nizwa, Department of Mathematical and Physical Sciences College of Arts and Science, Nizwa (Oman); Gupta, Y.K. [Raj Kumar Goel Institute of Technology, Department of Mathematics, Ghaziabad, Uttar Pradesh (India); Ray, Saibal [Government College of Engineering and Ceramic Technology, Department of Physics, Kolkata, West Bengal (India); Deb, Debabrata [Indian Institute of Engineering Science and Technology, Shibpur, Department of Physics, Howrah, West Bengal (India)

2016-12-15

In the present investigation an exact generalised model for anisotropic compact stars of embedding class 1 is sought with a general relativistic background. The generic solutions are verified by exploring different physical aspects, viz. energy conditions, mass-radius relation, stability of the models, in connection to their validity. It is observed that the model presented here for compact stars is compatible with all these physical tests and thus physically acceptable as far as the compact star candidates RXJ 1856-37, SAX J 1808.4-3658 (SS1) and SAX J 1808.4-3658 (SS2) are concerned. (orig.)

'Crescent'-shaped tokamak for compact ignition

International Nuclear Information System (INIS)

Yamazaki, K.; Reiersen, W.T.

1986-01-01

A compact high-beta tokamak configuration with ''crescent''-shaped (or ''boomerang''-shaped) cross section is proposed as a next-generation ignition machine. This configuration with a small indentation but a large triangularity is more compact than the normal dee-shaped design because of its high-beta characteristics in the first-second transition regime of stability. This may also be a more reliable next-generation compact device than the bean-shaped design with large indentation and small triangularity, because this design does not rely on the second stability and is easily extendable from the present dee-shaped design. (author)

Development of compact toroids injector for direct plasma controls

International Nuclear Information System (INIS)

Azuma, K.; Oda, Y.; Onozuka, M.; Uyama, T.; Nagata, M.; Fukumoto, N.

1995-01-01

The application of the compact toroids injector for direct plasma controls has been investigated. The compact toroids injection can fuel particles directly into the core of the plasma and modify the plasma profiles at the desired locations. The acceleration tests of the compact toroids have been conducted at Himeji Institute of Technology. The tests showed that the hydrogen compact toroid was accelerated up to 80km/s and the plasma density of the compact toroid was compressed to 1.2 x 10 21 m -3 . (orig.)

Buying and selling green: deregulation and green power marketing

International Nuclear Information System (INIS)

Evans, Andrew

2000-01-01

This article discusses the increasing trend towards deregulation of electricity markets, and the driving forces for liberalisation in the EU and North America. The use of green tariffs offered by utilities to differentiate themselves from competitors and to gain and keep customers is reported, and the situation with regard to green energy within the deregulated electricity markets in Australia, the EU, Denmark, Finland, Germany, the Netherlands, Portugal, Sweden, the UK, Canada and the USA is outlined. Customers switching as a result of green tariffs, the growing role of renewables, and opportunities for the promotion of green tariffs are discussed. (UK)

Analytical Methods for Malachite Green : Completion Report : Malachite Green Analysis in Water.

Energy Technology Data Exchange (ETDEWEB)

Allen, John L.; Gofus, Jane E.; Meinertz, Jeffery R.

1991-06-01

Malachite green is a known teratogen and therefore its use is limited to nonfood fish under an Investigational New Animal Drug permit (INAD), number 2573. Although a charcoal adsorption column was developed to remove malachite green from hatchery water, INAD compliance requires that the malachite green residue concentrations in any effluent from hatcheries using the chemical be quantified. Therefore, we developed a method for the analysis of malachite green residues in water. Enrichment of the residues of malachite green in water on a diol column followed by High Performance Liquid Chromatographic (HPLC) analysis gives a minimum sensitivity of less than 10 ppb for the chemical. When combined with post-column oxidation using a lead oxide post-column reactor, the procedure can be used for the simultaneous analysis of malachite green in its leuco form, a decomposition product of the dye, as well as its chromatic form. Recovery of the leuco form is pH dependent and water samples should be adjusted to pH 6 to optimize recovery of this form. Water samples spiked with malachite green were concentrated on a diol column followed by elution with 0.05 M p-toluene sulfonic acid in methanol. The methanol elutes were analyzed by HPLC. Pond water samples spiked with malachite green and leuco malachite green yielded average recoveries of 95.4% for malachite green and 57.3% for leuco malachite green. Tap water samples spiked with the carbinol form of malachite green gave average recoveries of 98.6%. The method is very sensitive and is capable of detecting malachite green residues in water at less than 10 ppb. Fish culturists, who cannot find an effective replacement for malachite green, can utilize the method to ensure that their effluents comply with INAD regulations. 13 refs., 2 figs., 7 tabs.

THE MEDIATION EFFECTS OF GREEN PERCEIVED CONSUMER SKEPTICISM AND GREEN PERCEIVED RISK IN THE RELATIONSHIP BETWEEN GREENWASHING AND GREEN TRUST

OpenAIRE

LEBLEBİCİ KOÇER, Leyla; DELİCE, Tuğba

2017-01-01

This study was carried out on the consumers in Kayseri and explores the influenceof greenwashing on green trust and discusses the mediation roles of green perceivedskepticism and green perceived risk. 430 consumers were participate in the research.Structural equation modelling was applied to test the research hypothesis. Thisstudy found that greenwashing has a negative association with green trust. In addition,it found that greenwashing is positively associated with green perceived consumersk...

Co-compact Gabor Systems on Locally Compact Abelian Groups

DEFF Research Database (Denmark)

Jakobsen, Mads Sielemann; Lemvig, Jakob

2016-01-01

In this work we extend classical structure and duality results in Gabor analysis on the euclidean space to the setting of second countable locally compact abelian (LCA) groups. We formulate the concept of rationally oversampling of Gabor systems in an LCA group and prove corresponding characteriz...

Agglomeration of powders with a new-coupled vibration-compaction device

Directory of Open Access Journals (Sweden)

Serris Eric

2017-01-01

Full Text Available Inorganic powder recycling should be a crucial process for the “smart factories” in the future. A complex three-phase system (bauxite mixed with ordinary Portland cement and water with a new-coupled vibration-compaction device is studied. The compressive stress of compacts seems to be improved by using this device at low compaction pressure leaving the other characteristics unchanged. The tomographic study of macroscopic porosities shows differences in the pores repartitions inside vibrated and untreated compacts. Classic porosity repartition is shown in the classic compacted bauxite compacts whereas in the vibrated-compacted bauxite exhibits inhomogeneities. Despite this, we find these results quite promising for further investigations.

Impact Compaction of a Granular Material

Science.gov (United States)

Fenton, Gregg; Asay, Blaine; Todd, Steve; Grady, Dennis

2017-06-01

The dynamic behavior of granular materials has importance to a variety of engineering applications. Although, the mechanical behavior of granular materials have been studied extensively for several decades, the dynamic behavior of these materials remains poorly understood. High-quality experimental data are needed to improve our general understanding of granular material compaction physics. This paper describes how an instrumented plunger impact system can be used to measure the compaction process for granular materials at high and controlled strain rates and subsequently used for computational modelling. The experimental technique relies on a gas-gun driven plunger system to generate a compaction wave through a volume of granular material. This volume of material has been redundantly instrumented along the bed length to track the progression of the compaction wave, and the piston displacement is measured with Photon Doppler Velocimetry (PDV). Using the gathered experimental data along with the initial material tap density, a granular material equation of state can be determined.

Development of compact toroids injector for direct plasma controls

Energy Technology Data Exchange (ETDEWEB)

Azuma, K. [Mitsubishi Heavy Industries Ltd., Takasago (Japan); Oda, Y. [Mitsubishi Heavy Industries Ltd., Takasago (Japan); Onozuka, M. [Mitsubishi Heavy Industries Ltd., Takasago (Japan); Uyama, T. [Himeji Inst. of Tech. (Japan); Nagata, M. [Himeji Inst. of Tech. (Japan); Fukumoto, N. [Himeji Inst. of Tech. (Japan)

1995-12-31

The application of the compact toroids injector for direct plasma controls has been investigated. The compact toroids injection can fuel particles directly into the core of the plasma and modify the plasma profiles at the desired locations. The acceleration tests of the compact toroids have been conducted at Himeji Institute of Technology. The tests showed that the hydrogen compact toroid was accelerated up to 80km/s and the plasma density of the compact toroid was compressed to 1.2 x 10{sup 21}m{sup -3}. (orig.).

Principles of control automation of soil compacting machine operating mechanism

Science.gov (United States)

Anatoly Fedorovich, Tikhonov; Drozdov, Anatoly

2018-03-01

The relevance of the qualitative compaction of soil bases in the erection of embankment and foundations in building and structure construction is given.The quality of the compactible gravel and sandy soils provides the bearing capability and, accordingly, the strength and durability of constructed buildings.It has been established that the compaction quality depends on many external actions, such as surface roughness and soil moisture; granulometry, chemical composition and degree of elasticity of originalfilled soil for compaction.The analysis of technological processes of soil bases compaction of foreign and domestic information sources showed that the solution of such important problem as a continuous monitoring of soil compaction actual degree in the process of machine operation carry out only with the use of modern means of automation. An effective vibrodynamic method of gravel and sand material sealing for the building structure foundations for various applications was justified and suggested.The method of continuous monitoring the soil compaction by measurement of the amplitudes and frequencies of harmonic oscillations on the compactible surface was determined, which allowed to determine the basic elements of facilities of soil compacting machine monitoring system of operating, etc. mechanisms: an accelerometer, a bandpass filter, a vibro-harmonics, an on-board microcontroller. Adjustable parameters have been established to improve the soil compaction degree and the soil compacting machine performance, and the adjustable parameter dependences on the overall indexhave been experimentally determined, which is the soil compaction degree.A structural scheme of automatic control of the soil compacting machine control mechanism and theoperation algorithm has been developed.

FEM modeling on the compaction of Fe and Al composite powders

Directory of Open Access Journals (Sweden)

Han P.

2015-01-01

Full Text Available The compaction process of Fe and Al composite powders subjected to single action die compaction was numerically modeled by FEM method. The relationship between the overall relative density and compaction pressure of the compacts with various Al contents was firstly identified, and the influences of Al content on the local relative density, stress, and their distributions were studied. Then the compaction pressure effects on the above properties with fixed Al content were discussed. Furthermore, detailed flow behaviors of the composite powders during compaction and the relationship between the compaction pressure and the ejection force/spring back of the compact were analyzed. The results show that: (1 With each compaction pressure, higher relative density can be realized with the increase of Al content and the relative density distribution tends to be uniform; (2 When the Al content is fixed, higher compaction pressure can lead to composite compact with higher relative density, and the equivalent Von Mises stress in the central part of the compact increases gradually; (3 Convective flow occurs at the top and bottom parts of the compact close to the die wall, each indicates a different flow behavior; (4 The larger the compaction pressure for each case, the higher the residual elasticity, and the larger the ejection force needed.

Effects of continuum breakdown on hypersonic aerothermodynamics for reacting flow

Science.gov (United States)

Holman, Timothy D.; Boyd, Iain D.

2011-02-01

This study investigates the effects of continuum breakdown on the surface aerothermodynamic properties (pressure, stress, and heat transfer rate) of a sphere in a Mach 25 flow of reacting air in regimes varying from continuum to a rarefied gas. Results are generated using both continuum [computational fluid dynamics (CFD)] and particle [direct simulation Monte Carlo (DSMC)] approaches. The DSMC method utilizes a chemistry model that calculates the backward rates from an equilibrium constant. A preferential dissociation model is modified in the CFD method to better compare with the vibrationally favored dissociation model that is utilized in the DSMC method. Tests of these models are performed to confirm their validity and to compare the chemistry models in both numerical methods. This study examines the effect of reacting air flow on continuum breakdown and the surface properties of the sphere. As the global Knudsen number increases, the amount of continuum breakdown in the flow and on the surface increases. This increase in continuum breakdown significantly affects the surface properties, causing an increase in the differences between CFD and DSMC. Explanations are provided for the trends observed.

Mechanical and chemical compaction in fine-grained shallow-water limestones.

Science.gov (United States)

Shinn, E.A.; Robbin, D.M.

1983-01-01

Significant mechanical compaction resulted from pressures simulating less than 305 m of burial. Increasing loads to an equivalent of more than 3400 m did not significantly increase compaction or reduce sediment core length. Chemical compaction (pressure dissolution) was detected only in sediment cores compacted to pressures greater than 3400 m of burial. These short-term experiments suggest that chemical compaction would begin at much shallower depths given geologic time. Compaction experiments that caused chemical compaction lend support to the well-established hypothesis; that cement required to produce a low-porosity/low-permeability fine-grained limestone is derived internally. Dissolution, ion diffusion, and reprecipitation are considered the most likely processes for creating significant thicknesses of dense limestone in the geologic record. Continuation of chemical compaction after significant porosity reduction necessitates expulsion of connate fluids, possibly including hydrocarbons. -from Authors

Green Chemistry

Energy Technology Data Exchange (ETDEWEB)

Collison, Melanie

2011-05-15

Green chemistry is the science of chemistry used in a way that will not use or create hazardous substances. Dr. Rui Resendes is working in this field at GreenCentre Canada, an offshoot of PARTEQ Innovations in Kingston, Ontario. GreenCentre's preliminary findings suggest their licensed product {sup S}witchable Solutions{sup ,} featuring 3 classes of solvents and a surfactant, may be useful in bitumen oil sands extraction.

Bone compaction enhances implant fixation in a canine gap model

DEFF Research Database (Denmark)

Kold, Søren; Rahbek, Ole; Toft, Marianne

2005-01-01

A new bone preparation technique, compaction, has increased fixation of implants inserted with exact-fit or press-fit to bone. Furthermore, a demonstrated spring-back effect of compacted bone might be of potential value in reducing the initial gaps that often exist between clinical inserted...... implants and bone. However, it is unknown whether the compression and breakage of trabeculae during the compaction procedure results in impaired gap-healing of compacted bone. Therefore, we compared compaction with conventional drilling in a canine gap model. Grit-blasted titanium implants (diameter 6 mm...... that the beneficial effect of reduced gap size, as compacted bone springs back, is not eliminated by an impaired gap-healing of compacted bone....

Modeling compaction-induced energy dissipation of granular HMX

Energy Technology Data Exchange (ETDEWEB)

Gonthier, K.A. [Lamar Univ., Beaumont, TX (US). Dept. of Mechanical Engineering; Menikoff, R.; Son, S.F.; Asay, B.W. [Los Alamos National Lab., NM (US)

1998-12-31

A thermodynamically consistent model is developed for the compaction of granular solids. The model is an extension of the single phase limit of two-phase continuum models used to describe Deflagration-to-Detonation Transition (DDT) experiments. The focus is on the energetics and dissipation of the compaction process. Changes in volume fraction are partitioned into reversible and irreversible components. Unlike conventional DDT models, the model is applicable from the quasi-static to dynamic compaction regimes for elastic, plastic, or brittle materials. When applied to the compaction of granular HMX (a brittle material), the model predicts results commensurate with experiments including stress relaxation, hysteresis, and energy dissipation. The model provides a suitable starting point for the development of thermal energy localization sub-scale models based on compaction-induced dissipation.

Multiphase reacting flows modelling and simulation

CERN Document Server

Marchisio, Daniele L

2007-01-01

The papers in this book describe the most widely applicable modeling approaches and are organized in six groups covering from fundamentals to relevant applications. In the first part, some fundamentals of multiphase turbulent reacting flows are covered. In particular the introduction focuses on basic notions of turbulence theory in single-phase and multi-phase systems as well as on the interaction between turbulence and chemistry. In the second part, models for the physical and chemical processes involved are discussed. Among other things, particular emphasis is given to turbulence modeling strategies for multiphase flows based on the kinetic theory for granular flows. Next, the different numerical methods based on Lagrangian and/or Eulerian schemes are presented. In particular the most popular numerical approaches of computational fluid dynamics codes are described (i.e., Direct Numerical Simulation, Large Eddy Simulation, and Reynolds-Averaged Navier-Stokes approach). The book will cover particle-based meth...

Strategy Guideline. Compact Air Distribution Systems

Energy Technology Data Exchange (ETDEWEB)

Burdick, Arlan [IBACOS, Inc., Pittsburgh, PA (United States)

2013-06-01

This guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

Green Vehicle Guide

Science.gov (United States)

... label Buy green. Save green. Learn about MPG math Discover fuel-saving tips Promote green ... U.S. consumers who have already purchased new vehicles under the fuel economy & greenhouse gas standard! More about the standards » Check ...

The use of compaction in the manufacture of tablets

Directory of Open Access Journals (Sweden)

O. V. Tryhubchak

2016-08-01

Full Text Available In the production of tablets direct compression method, wet and dry granulationare used. Dry granulation can be used if materials have sufficient cohesive properties to form granules. Scientific publications of recent years clearly demonstrate the prospects of roller compaction using in pharmaceutical industry. Aim. The aim of work is to generalize available data regarding to the use of compaction in the pharmaceutical industry. Materials and methods. We have studied and analyzed the available scientific sources in order to generalize the available literature on the use of compacting in the production of the tablets. During this study we used methods of observation and systematization analysis. Results. Materials for compaction characteristics of the process, its benefits and conditions of application have been collected and systematized, parameters of process have been selected, theories of compaction have been generalized, the characteristics and examples of compaction equipment have been adduced, and the key characteristics of the material used in the pharmaceutical industry have been demonstrated. Compacting is dry granulation technology in which powder containing active ingredients and excipients are compacted between two opposing spinning rollers by applying mechanical pressure. Compared with the original powder, granules after compression are characterized by much better fluidity and higher density by reducing the volume. The roller consolidation process substantially affects the particle size distribution, flowability, homogeneity, pressing, compaction substances and excipients, therefore, can affect dissolution, time of disintegration, resistance to crushing, abrasion of tablets. The main parameters of compacting are seal and method of its application, conditions and speed of the process. Conclusions. It has been established that the use of compacting decreases or increases particles size to form granules, which leads to improved

Land subsidence and hydrodynamic compaction of sedimentary basins

Directory of Open Access Journals (Sweden)

H. Kooi

1998-01-01

Full Text Available A one-dimensional model is used to investigate the relationship between land subsidence and compaction of basin sediments in response to sediment loading. Analysis of the model equations and numerical experiments demonstrate quasi-linear systems behaviour and show that rates of land subsidence due to compaction: (i can attain a significant fraction (>40% of the long-term sedimentation rate; (ii are hydrodynamically delayed with respect to sediment loading. The delay is controlled by a compaction response time τc that can reach values of 10-5-107 yr for thick shale sequences. Both the behaviour of single sediment layers and multiple-layer systems are analysed. Subsequently the model is applied to the coastal area of the Netherlands to illustrate that lateral variability in compaction-derived land subsidence in sedimentary basins largely reflects the spatial variability in both sediment loading and compaction response time. Typical rates of compaction-derived subsidence predicted by the model are of the order of 0.1 mm/yr but may reach values in excess of 1 mm/yr under favourable conditions.

Non-equilibrium reacting gas flows kinetic theory of transport and relaxation processes

CERN Document Server

Nagnibeda, Ekaterina; Nagnibeda, Ekaterina

2009-01-01

This volume develops the kinetic theory of transport phenomena and relaxation processes in the flows of reacting gas mixtures. The theory is applied to the modeling of non-equilibrium flows behind strong shock waves, in the boundary layer, and in nozzles.

DNA compaction by azobenzene-containing surfactant

International Nuclear Information System (INIS)

Zakrevskyy, Yuriy; Kopyshev, Alexey; Lomadze, Nino; Santer, Svetlana; Morozova, Elena; Lysyakova, Ludmila; Kasyanenko, Nina

2011-01-01

We report on the interaction of cationic azobenzene-containing surfactant with DNA investigated by absorption and fluorescence spectroscopy, dynamic light scattering, and atomic force microscopy. The properties of the surfactant can be controlled with light by reversible switching of the azobenzene unit, incorporated into the surfactant tail, between a hydrophobic trans (visible irradiation) and a hydrophilic cis (UV irradiation) configuration. The influence of the trans-cis isomerization of the azobenzene on the compaction process of DNA molecules and the role of both isomers in the formation and colloidal stability of DNA-surfactant complexes is discussed. It is shown that the trans isomer plays a major role in the DNA compaction process. The influence of the cis isomer on the DNA coil configuration is rather small. The construction of a phase diagram of the DNA concentration versus surfactant/DNA charge ratio allows distancing between three major phases: colloidally stable and unstable compacted globules, and extended coil conformation. There is a critical concentration of DNA above which the compacted globules can be hindered from aggregation and precipitation by adding an appropriate amount of the surfactant in the trans configuration. This is because of the compensation of hydrophobicity of the globules with an increasing amount of the surfactant. Below the critical DNA concentration, the compacted globules are colloidally stable and can be reversibly transferred with light to an extended coil state.

'REACTS'. A pragmatic approach for providing medical care and physician education for radiation emergencies

International Nuclear Information System (INIS)

Lushbaugh, C.C.; Andrews, G.A.; Huebner, K.F.; Cloutier, R.J.; Beck, W.L.; Berger, J.D.

1976-01-01

Because serious radiation incidents have been rare, few medical personnel (notably only some in France, Russia, Belgium, Canada, Yugoslavia, Japan, Great Britain and the United States) have first-hand experience in radiation-accident management. The generation of physicians who participated in those accidents now needs to pass on the bits of knowledge that were gleaned from them. These case histories are difficult for the local, non-radiology physician to obtain when he is called upon to help formulate the medical-emergency response plan required everywhere for licensing power reactors. The Radiation Emergency Assistance Center and Training Site (REACTS) in Oak Ridge, Tennessee, supported by the US Energy Research and Development Administration, is designed to meet these medical and educational needs. REACTS, located in the Oak Ridge Hospital of the Methodist Church, is not involved in the hospital's daily community functions except insofar as REACTS is the radiation emergency arm of the area's major disaster plan. Its dual mission is training physicians, nurses, and paramedical emergency personnel in radiation-accident management, and treating irradiated and contaminated persons. Its training activities are carried out by the Special Training Division of Oak Ridge Associated Universities. Formal courses in radiation medicine and health physics and practical laboratory experience are now conducted twice a year for physicians. They will be expanded in the future to include training of paramedical personnel. Follow-up studies of radiation-accident survivors are carried out in REACTS to ensure the preservation of valuable human data and radiation-accident experiences. This unique facility and its staff are dedicated to meet the needs of the far-flung public and private medical domains in the United States for nuclear-production energy

Tax havens under international pressure: How do they react?

OpenAIRE

Patrice Pieretti; Giuseppe Pulina

2015-01-01

This paper contributes to the literature about tax havens by providing a more comprehensive analysis of their role. The aim is to analyze how low-tax jurisdictions can react to growing international pressure exerted, by high-tax countries, to enforce compliance with anti aggressive tax planning standards. To this end, we model how a small tax haven tries to be attractive to multinationals located in a high-tax region by providing aggressive tax planning services and/or a favorable environment...

Compact torsatron reactors

International Nuclear Information System (INIS)

Lyon, J.F.; Carreras, B.A.; Lynch, V.E.; Tolliver, J.S.; Sviatoslavsky, I.N.

1988-05-01

Low-aspect-ratio torsatron configurations could lead to compact stellarator reactors with R 0 = 8--11m, roughly one-half to one-third the size of more conventional stellarator reactor designs. Minimum-size torsatron reactors are found using various assumptions. Their size is relatively insensitive to the choice of the conductor parameters and depends mostly on geometrical constraints. The smallest size is obtained by eliminating the tritium breeding blanket under the helical winding on the inboard side and by reducing the radial depth of the superconducting coil. Engineering design issues and reactor performance are examined for three examples to illustrate the feasibility of this approach for compact reactors and for a medium-size (R 0 ≅ 4 m,/bar a/ /approx lt/ 1 m) copper-coil ignition experiment. 26 refs., 11 figs., 7 tabs

Compact fusion reactors

CERN Multimedia

CERN. Geneva

2015-01-01

Fusion research is currently to a large extent focused on tokamak (ITER) and inertial confinement (NIF) research. In addition to these large international or national efforts there are private companies performing fusion research using much smaller devices than ITER or NIF. The attempt to achieve fusion energy production through relatively small and compact devices compared to tokamaks decreases the costs and building time of the reactors and this has allowed some private companies to enter the field, like EMC2, General Fusion, Helion Energy, Lawrenceville Plasma Physics and Lockheed Martin. Some of these companies are trying to demonstrate net energy production within the next few years. If they are successful their next step is to attempt to commercialize their technology. In this presentation an overview of compact fusion reactor concepts is given.

On compact multipliers of topological algebras

International Nuclear Information System (INIS)

Mohammad, N.

1994-08-01

It is shown that if the maximal ideal space Δ(A) of a semisimple commutative complete metrizable locally convex algebra contains no isolated points, then every compact multiplier is trivial. Particularly, compact multipliers on semisimple commutative Frechet algebras whose maximal ideal space has no isolated points are identically zero. (author). 5 refs

The classification of 2-compact groups

DEFF Research Database (Denmark)

K. S. Andersen, Kasper; Grodal, Jesper

2009-01-01

with Moeller and Viruel for p odd, this establishes the full classification of p-compact groups, stating that, up to isomorphism, there is a one-to-one correspondence between connected p-compact groups and root data over the p-adic integers. As a consequence we prove the maximal torus conjecture, giving a one...

Ultra high frequency induction welding of powder metal compacts

Energy Technology Data Exchange (ETDEWEB)

Cavdar, U.; Gulsahin, I.

2014-10-01

The application of the iron based Powder Metal (PM) compacts in Ultra High Frequency Induction Welding (UHFIW) were reviewed. These PM compacts are used to produce cogs. This study investigates the methods of joining PM materials enforceability with UHFIW in the industry application. Maximum stress and maximum strain of welded PM compacts were determined by three point bending and strength tests. Microhardness and microstructure of induction welded compacts were determined. (Author)

Ultra high frequency induction welding of powder metal compacts

International Nuclear Information System (INIS)

Cavdar, U.; Gulsahin, I.

2014-01-01

The application of the iron based Powder Metal (PM) compacts in Ultra High Frequency Induction Welding (UHFIW) were reviewed. These PM compacts are used to produce cogs. This study investigates the methods of joining PM materials enforceability with UHFIW in the industry application. Maximum stress and maximum strain of welded PM compacts were determined by three point bending and strength tests. Microhardness and microstructure of induction welded compacts were determined. (Author)

Responding to excessive alcohol consumption in third-level (REACT): a study protocol.

Science.gov (United States)

Davoren, Martin P; Calnan, Susan; Mulcahy, Judith; Lynch, Emily; Perry, Ivan J; Byrne, Michael

2018-05-11

Problem alcohol use is an ongoing, worldwide phenomenon of considerable concern. Throughout the past 20 years, national policies have noted the importance of students when tackling alcohol consumption. Considering alcohol is a multifaceted issue, a multi-component response is required to combat its excessive use. This protocol sets out the approach used for developing, implementing and evaluating the REACT (Responding to Excessive Alcohol Consumption in Third-level) Programme. This evaluation will provide the evidence base for programme development, implementation and improvement. Stage one involved defining the multi-component intervention. This was developed following a systematic review of existing literature and a Delphi-consensus workshop involving university students, staff and relevant stakeholders. Following this, the programme is being implemented across the Higher Education sector in Ireland. A number of Higher Education Institutes have declined the invitation to participate in the programme. These institutions will act as control sites. Each intervention site will have a steering committee whose membership will include a mix of students and academic and student service staff. This steering committee will report to the REACT research team on the implementation of mandatory and optional action points at local sites. An online cross-sectional study at baseline and two-years post intervention will be utilised to determine the impact of the REACT programme. The impact assessment will focus on (1) whether the intervention has reduced alcohol consumption among third-level students (2); whether the programme altered students attitudes toward alcohol and (3) whether the programme has decreased the second-hand effects associated with excessive consumption. Finally, qualitative research will focus on factors influencing the take-up and implementation of this programme as well as students' views on the initiative. Alcohol consumption has remained on the policy

Compaction of an Oxisol and chemical composition of palisadegrass

Directory of Open Access Journals (Sweden)

Eurico Lucas de Sousa Neto

2013-08-01

Full Text Available Compaction is an important problem in soils under pastoral land use, and can make livestock systems unsustainable. The objective of this research was to study the impact of soil compaction on yield and quality of palisade (UROCHLOA BRIZANTHA cv. Marandu. The experiment was conducted on an Oxisol in the State of Mato Grosso, Brazil. Treatments consisted of four levels of soil compaction: no compaction (NC, slight compaction (SC, medium compaction (MC and high compaction (HC. The following soil properties were evaluated (layers 0-0.05 and 0.05-0.10 m: aggregate size distribution, bulk density (BD, macroporosity, microporosity, total porosity (TP, relative compaction (RC, and the characteristics of crude protein (CP, neutral detergent fiber (NDF, acid detergent fiber (ADF and dry matter yield (DMY of the forage. Highly compacted soil had high BD and RC, and low TP (0-0.05 m. Both DMY and CP were affected by HC, and both were strongly related to BD. Higher DMY (6.96 Mg ha-1 and CP (7.8 % were observed in the MC treatment (BD 1.57 Mg m-3 and RC 0.91 Mg m-3, in 0-0.05 m. A high BD of 1.57 Mg m-3 (0-0.05 m did not inhibit plant growth. The N concentration in the palisade biomass differed significantly among compaction treatments, and was 8.72, 11.20, 12.48 and 10.98 g kg-1 in NC, SC, MC and HC treatments, respectively. Increase in DMY and CP at the MC level may be attributed to more absorption of N in this coarse-textured soil.

Explaining compact groups as change alignments

International Nuclear Information System (INIS)

Mamon, G.A.

1990-01-01

The physical nature of the apparently densest groups of galaxies, known as compact groups is a topic of some recent controversy, despite the detailed observations of a well-defined catalog of 100 isolated compact groups compiled by Hickson (1982). Whereas many authors have espoused the view that compact groups are bound systems, typically as dense as they appear in projection on the sky (e.g., Williams ampersand Rood 1987; Sulentic 1987; Hickson ampersand Rood 1988), others see them as the result of chance configurations within larger systems, either in 1D (chance alignments: Mamon 1986; Walke ampersand Mamon 1989), or in 3D (transient cores: Rose 1979). As outlined in the companion review to this contribution (Mamon, in these proceedings), the implication of Hickson's compact groups (HCGs) being dense bound systems is that they would then constitute the densest isolated systems of galaxies in the Universe and the privileged site for galaxy interactions. In a previous paper (Mamon 1986), the author reviewed the arguments given for the different theories of compact groups. Since then, a dozen papers have been published on the subject, including a thorough and perceptive review by White (1990), thus more than doubling the amount written on the subject. Here, the author first enumerates the arguments that he brought up in 1986 substantiating the chance alignment hypothesis, then he reviews the current status of the numerous recent arguments arguing against chance alignments and/or for the bound dense group hypothesis (both for the majority of HCGs but not all of them), and finally he reconsiders each one of these anti-chance alignment arguments and shows that, rather than being discredited, the chance alignment hypothesis remains a fully consistent explanation for the nature of compact groups

Analysis of the cold compaction behaviour of TiH2-316L nanocomposite powder blend using compaction models

CSIR Research Space (South Africa)

Machio, Christopher N

2015-07-01

Full Text Available The paper captures the effect of structure and the applicability of compaction models using the cold compaction of a TiH2-SS316L composite powder prepared by high energy mechanical milling. The composite blend was cold pressed uniaxially...

THE STABILITY OF OPTICALLY THIN REACTING PLASMAS: EFFECTS OF THE BULK VISCOSITY

International Nuclear Information System (INIS)

Ibanez S, Miguel H.

2009-01-01

The thermochemical stability of reacting plasmas is analyzed by taking into account the change in the thermodynamical equilibrium values during the fluctuation. This shift in the equilibrium produces two main effects: a change in the four instability criteria for reacting gases resulting when the above effect is neglected and adds a fifth instability criterion due to the fact that the corresponding secular equation becomes a fifth-order polynomial. The above results are applied to several plasma models, in particular, to a photoionized hydrogen plasma for which the bulk viscosity can be more important than the dynamic viscosity and the thermometric conductivity. Therefore, the bulk viscosity may quench thermochemical instabilities were the thermal conduction is unable of stabilizing. This occurs for low values of the photoionizing energy E. The implications of the above results in explaining the formation of clump structures in different regions of the interstellar medium are outlined.

Automorphisms of p-compact groups and their root data

DEFF Research Database (Denmark)

Andersen, Kasper K. S.; Grodal, Jesper Kragh

2008-01-01

We construct a model for the space of automorphisms of a connected p–compact group in terms of the space of automorphisms of its maximal torus normalizer and its root datum. As a consequence we show that any homomorphism to the outer automorphism group of a p–compact group can be lifted to a group...... action, analogous to   a classical theorem of de Siebenthal for compact Lie groups. The model of this paper is used in a crucial way in our paper `The classification of 2-compact groups' [arXiv:math.AT/0611437], where we prove the conjectured classification of 2–compact groups and determine...... their automorphism spaces....

The green agenda

CERN Document Server

Calder, Alan

2009-01-01

This business guide to Green IT was written to introduce, to a business audience, the opposing groups and the key climate change concepts, to provide an overview of a Green IT strategy and to set out a straightforward, bottom line-orientated Green IT action plan.

Sustainable house construction and green financing. Explanation for 'green mortgages'

International Nuclear Information System (INIS)

1997-05-01

The Dutch government finances the sustainable construction of new houses by means of so-called 'green loans'. Extra costs for the construction of a sustainable house are compensated by a lower interest rate for a green loan. In this brochure it is explained when green financing of house construction is possible and how to apply for such loans

Pharmaceutical powder compaction technology

National Research Council Canada - National Science Library

Çelik, Metin

2011-01-01

"Revised to reflect modern pharmaceutical compacting techniques, this Second Edition guides pharmaceutical engineers, formulation scientists, and product development and quality assurance personnel...

Materials study for reacting plasma machine

International Nuclear Information System (INIS)

Kamada, Kohji; Hamada, Yasuji

1982-01-01

A new reacting plasma machine is designed, and will be constructed at the Institute of Plasma Physics, Nagoya University. It is important to avoid the activation of the materials for the machine, accordingly, aluminum alloy has been considered as the material since the induced activity of aluminum due to 14 MeV neutrons is small. The vacuum chamber of the new machine consists of four modules, and the remote control of each module is considered. However, the cost of the remote control of modules is expensive. To minimize the dependence on the remote control, the use of aluminum alloy is considered as the first step. The low electrical resistivity, over-ageing, weak mechanical strength and eddy current characteristics of aluminum alloy must be improved. The physical and electrical properties of various aluminum alloys have been investigated. Permeability of hydrogen through aluminum, the recycling characteristics and surface coating materials have been also studied. (Kato, T.)

Inhomogeneous compact extra dimensions

Energy Technology Data Exchange (ETDEWEB)

Bronnikov, K.A. [Center of Gravity and Fundamental Metrology, VNIIMS, 46 Ozyornaya st., Moscow 119361 (Russian Federation); Budaev, R.I.; Grobov, A.V.; Dmitriev, A.E.; Rubin, Sergey G., E-mail: kb20@yandex.ru, E-mail: buday48@mail.ru, E-mail: alexey.grobov@gmail.com, E-mail: alexdintras@mail.ru, E-mail: sergeirubin@list.ru [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute), 115409 Moscow (Russian Federation)

2017-10-01

We show that an inhomogeneous compact extra space possesses two necessary features— their existence does not contradict the observable value of the cosmological constant Λ{sub 4} in pure f ( R ) theory, and the extra dimensions are stable relative to the 'radion mode' of perturbations, the only mode considered. For a two-dimensional extra space, both analytical and numerical solutions for the metric are found, able to provide a zero or arbitrarily small Λ{sub 4}. A no-go theorem has also been proved, that maximally symmetric compact extra spaces are inconsistent with 4D Minkowski space in the framework of pure f ( R ) gravity.

Engineering aspects of compact stellarators

International Nuclear Information System (INIS)

Nelson, B.E.; Benson, R.D.; Brooks, A.

2003-01-01

Compact stellarators could combine the good confinement and high beta of a tokamak with the inherently steady state, disruption-free characteristics of a stellarator. Two U.S. compact stellarator facilities are now in the conceptual design phase: the National Compact Stellarator Experiment (NCSX) and the Quasi- Poloidal Stellarator (QPS). NCSX has a major radius of 1.4 m and a toroidal field up to 2 T. The primary feature of both NCSX and QPS is the set of modular coils that provide the basic magnetic configuration. These coils represent a major engineering challenge due to the complex shape, precise geometric accuracy, and high current density of the windings. The winding geometry is too complex for conventional hollow copper conductor construction. Instead, the modular coils will be wound with flexible, multi strand cable conductor that has been compacted to a 75% copper packing fraction. Inside the NCSX coil set and surrounding the plasma is a highly contoured vacuum vessel. The vessel consists of three identical, 120 deg. segments that are bolted together at double sealed joints. The QPS device has a major radius of 0.9 m, a toroidal field of 1 T, and an aspect ratio of only 2.7. Instead of an internal vacuum vessel, the QPS modular coils will operate in an external vacuum tank. (author)

Effect of Subsoil Compaction on Hydraulic Parameters

DEFF Research Database (Denmark)

Iversen, Bo Vangsø; Berisso, Feto Esimo; Schjønning, Per

Soil compaction is a major threat to sustainable soil quality and is increasing since agricultural machinery is becoming heavier and is used more intensively. Compaction not only reduces pore volume, but also modifies the pore connectivity. The inter-Nordic research project POSEIDON (Persistent...... effects of subsoil compaction on soil ecological services and functions) put forward the hypothesis that due to a decrease in the hydraulic conductivity in the soil matrix, compaction increases the frequency of preferential flow events in macropores and therefore increases the leaching of otherwise....... In the field the near-saturated hydraulic conductivity was measured with a tension infiltrometer in the same treatments at a depth of 30 cm. In the laboratory saturated and near-saturated hydraulic conductivity and the bulk density were measured as well. Also, macropores in the large soil cores were made...

Compact turbidity meter

Science.gov (United States)

Hirschberg, J. G.

1979-01-01

Proposed monitor that detects back-reflected infrared radiation makes in situ turbidity measurements of lakes, streams, and other bodies of water. Monitor is compact, works well in daylight as at night, and is easily operated in rough seas.

Green roofs

CSIR Research Space (South Africa)

Van Wyk, Llewellyn V

2010-04-01

Full Text Available , beetles and spiders); and the number of birds that nest in vegetated roofs (including kestrels, swallows, and wagtails). Objective The primary objective of a green roof is to create a living habitat in an otherwise barren environment, hence the use... the negative environmental impacts including plant and insect specie loss. Thus at a philosophical level green roofs support the notion “replace what you displace”. Key ecological issues that can be addressed through green roofs include: Negative effects...

Strategy Guideline: Compact Air Distribution Systems

Energy Technology Data Exchange (ETDEWEB)

Burdick, A.

2013-06-01

This Strategy Guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. Traditional systems sized by 'rule of thumb' (i.e., 1 ton of cooling per 400 ft2 of floor space) that 'wash' the exterior walls with conditioned air from floor registers cannot provide appropriate air mixing and moisture removal in low-load homes. A compact air distribution system locates the HVAC equipment centrally with shorter ducts run to interior walls, and ceiling supply outlets throw the air toward the exterior walls along the ceiling plane; alternatively, high sidewall supply outlets throw the air toward the exterior walls. Potential drawbacks include resistance from installing contractors or code officials who are unfamiliar with compact air distribution systems, as well as a lack of availability of low-cost high sidewall or ceiling supply outlets to meet the low air volumes with good throw characteristics. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

Thermal properties of wood reacted with a phosphorus pentoxide–amine system

Science.gov (United States)

Hong-Lin Lee; George C. Chen; Roger M. Rowell

2004-01-01

The objective of this research was to improve the fire-retardant properties of wood in one treatment using a phosphorus pentoxide–amine system. Phosphorus pentoxide and 16 amines including alkyl, halophenyl, and phenyl amines were compounded in N,N-dimethylformamide and the resulting solutions containing phosphoramides were reacted with wood. The characteristics of...

Siting actions in compacts and nonmember states

International Nuclear Information System (INIS)

Tullis, J.

1986-05-01

This paper examines the status of siting actions in those compacts and states currently progressing with siting studies. The efforts of the Central Compact Commission, Texas, California, Colorado and Illinois are highlighted to illustrate progress, methodology, and problems encountered

ReACT Methodology Proof of Concept Final Report

Energy Technology Data Exchange (ETDEWEB)

Bri Rolston; Sarah Freeman

2014-03-01

The Department of Energy’s Office of Electricity Delivery and Energy Reliability (DOE-OE) funded INL Researchers to evaluate a novel process for assessing and mitigating cyber security risks. The proof of concept level of the method was tested in an industry environment. This case study, plus additional case studies will support the further development of the method into a tool to assist industry in securing their critical networks. This report provides an understanding of the process developed in the Response Analysis and Characterization Tool (ReACT) project. This report concludes with lessons learned and a roadmap for final development of these tools for use by industry.

42 CFR 137.30 - What is a self-governance compact?

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false What is a self-governance compact? 137.30 Section... SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES TRIBAL SELF-GOVERNANCE Self-Governance compact § 137.30 What is a self-governance compact? A self-governance compact is a legally binding and mutually...

25 CFR 1000.161 - What is a self-governance compact?

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false What is a self-governance compact? 1000.161 Section 1000... EDUCATION ACT Negotiation Process for Annual Funding Agreements Negotiating A Self-Governance Compact § 1000.161 What is a self-governance compact? A self-governance compact is an executed document that affirms...

Green energy in Europe: selling green energy with green certificates

International Nuclear Information System (INIS)

Ouillet, L.

2002-01-01

Sales of green power products are booming in Europe: 50,000 customers in the United Kingdom, 775,000 in the Netherlands and 300,000 in Germany. Laws of physics are however formal: the way in which electricity flows within the grid does not allow suppliers to assure customers that they are directly receiving electricity produced exclusively from renewable energy sources. What are marketers selling their customers then? Laetitia Ouillet, Greenprices, takes a closer look and focuses on the potential of selling green energy in the forms of renewable energy certificates. (Author)

Ultra-compact Ku band rectenna

OpenAIRE

Takacs , Alexandru; Aubert , Hervé; Charlot , Samuel

2015-01-01

International audience; This paper addresses an innovative and ultra-compact rectenna designed for energy harvesting or wireless power transfer applications. The presented rectenna uses a printed cross dipoles antenna array and a rectifier implemented with only one silicon Schottky diode. Experimental results show that 1.15 mW of DC power can be obtained for an optimal load impedance of 500 Ω using a compact rectenna (2.5 cm 2 or 0.6 square wavelength) illuminated by an electric field of 60 V...

Rate type isotach compaction of consolidated sandstone

NARCIS (Netherlands)

Waal, J.A. de; Thienen-Visser, K. van; Pruiksma, J.P.

2015-01-01

Laboratory experiments on samples from a consolidated sandstone reservoir are presented that demonstrate rate type compaction behaviour similar to that observed on unconsolidated sands and soils. Such rate type behaviour can have large consequences for reservoir compaction, surface subsidence and

COMPACTION OF FIBERBOARD IN A 9975 SHIPPING PACKAGE

Energy Technology Data Exchange (ETDEWEB)

Stefek, T.; Daugherty, W.; Estochen, E.; Leduc, D.

2011-05-11

Compaction of lower layers in the fiberboard overpack has been observed in 9975 packages that contain elevated moisture. Lab testing has resulted in a better understanding of (1) the relationship between the fiberboard moisture level and compaction of the lower fiberboard assembly, and (2) the behavior of the fiberboard during transport. In laboratory tests, higher moisture content has been shown to correspond to higher total compaction of fiberboard material, greater rate of compaction, and continued compaction over a longer period of time. In addition, laboratory tests have shown that the application of a dynamic load results in higher fiberboard compaction. The test conditions and sample geometric/loading configurations were chosen to simulate the regulatory requirements for 9975 package input dynamic loading. Dynamic testing was conducted over a period of several months to acquire immediate and cumulative changes in geometric data for various moisture levels. Currently, one sample set has undergone a complete dynamic test regimen, while testing of another set is still in-progress. The dynamic input, data acquisition, test effects on sample dynamic parameters, and interim results from this test program will be summarized and compared to regulatory specifications for dynamic loading. This will provide a basis from which to evaluate the impact of moisture and fiberboard compaction on the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Documented Safety Analysis) at the Savannah River Site (SRS).

Means, methods and performances of the AREVA's HTR compact controls

International Nuclear Information System (INIS)

Banchet, J.; Guillermier, P.; Tisseur, D.; Vitali, M. P.

2008-01-01

In the AREVA's HTR development program, the reactor plant is composed of a prismatic core containing graphite cylindrical fuel elements, called compacts, where TRISO particles are dispersed. Starting from its past compacting process, the latter being revamped through the use of state of the art equipments, CERCA, 100% AREVA NP's subsidiary, was able to recover the quality of past compacts production. The recovered compacting process is composed of the following manufacturing steps: graphite matrix granulation, mix between the obtained granulates and particles, compacting and calcining at low pressure and temperature. To adapt this past process to new manufacturing equipments, non destructive examination tests were carried out to assess the compact quality, the latter being assessed via in house developed equipments and methods at each step of the design of experiments. As for the manufacturing process, past quality control methods were revamped to measure compact dimensional features (diameter, perpendicularity and cone effect), visual aspect, SiC layer failure fraction (via anodic disintegration and burn leach test) and homogeneity via 2D radiography coupled to ceramography. Although meeting quality requirements, 2D radiography method could not provide a quantified specification for compact homogeneity characterization. This limitation yielded the replacement of this past technique by a method based on X-Ray tomography. Development was conducted on this new technique to enable the definition of a criterion to quantify compact homogeneity, as well as to provide information about the distances in between particles. This study also included a comparison between simulated and real compacts to evaluate the accuracy of the technique as well as the influence of particle packing fraction on compact homogeneity. The developed quality control methods and equipments guided the choices of manufacturing parameters adjustments at the development stage and are now applied for

True Green and Sustainable University Campuses? Toward a Clusters Approach

Directory of Open Access Journals (Sweden)

Giulia Sonetti

2016-01-01

Full Text Available Campus greening is often the first step universities take towards sustainability. However, the diffusion of sustainability reporting methodologies and rankings is still at an early stage, and is biased in mainly measuring energy efficiency indicators while omitting basic features enabling meaningful comparisons among centers or addressing social (users aspects related to long term sustainability transitions. This paper aims to introduce a critical perspective on sustainability university frameworks through: (i a review of current Campus Sustainability Assessments (CSAs; (ii performing and comparing the results obtained from the application of two internationally recognized CSAs (namely, Green Metric and ISCN to two case studies (the Politecnico di Torino, in Italy, and the Hokkaido University, In Japan and, finally, (iii proposing a new CSA approach that encompasses clusters of homogeneous campus typologies for meaningful comparisons and university rankings. The proposed clusters regard universities’ morphological structures (campuses nested within city centers versus outside of a city compact ones, climatic zones and functions. At the micro scale, the paper introduces the need for indicators beyond measuring pure energy efficiency, but which are attentive to local and societal constraints and provide long-term tracking of outcomes. This, better than a sheer record of sustainability priority actions, can help in building homogenous university case studies to find similar and scalable success strategies and practices, and also in self-monitoring progress toward achieving truly sustainable university campuses.

Layer-by-layer assembly of multicolored semiconductor quantum dots towards efficient blue, green, red and full color optical films

International Nuclear Information System (INIS)

Zhang Jun; Li Qian; Di Xiaowei; Liu Zhiliang; Xu Gang

2008-01-01

Multicolored semiconductor quantum dots have shown great promise for construction of miniaturized light-emitting diodes with compact size, low weight and cost, and high luminescent efficiency. The unique size-dependent luminescent property of quantum dots offers the feasibility of constructing single-color or full-color output light-emitting diodes with one type of material. In this paper, we have demonstrated the facile fabrication of blue-, green-, red- and full-color-emitting semiconductor quantum dot optical films via a layer-by-layer assembly technique. The optical films were constructed by alternative deposition of different colored quantum dots with a series of oppositely charged species, in particular, the new use of cationic starch on glass substrates. Semiconductor ZnSe quantum dots exhibiting blue emission were deposited for fabrication of blue-emitting optical films, while semiconductor CdTe quantum dots with green and red emission were utilized for construction of green- and red-emitting optical films. The assembly of integrated blue, green and red semiconductor quantum dots resulted in full-color-emitting optical films. The luminescent optical films showed very bright emitting colors under UV irradiation, and displayed dense, smooth and efficient luminous features, showing brighter luminescence in comparison with their corresponding quantum dot aqueous colloid solutions. The assembled optical films provide the prospect of miniaturized light-emitting-diode applications.

Green Roofs: A Part of Green Infrastructure Strategy for Urban Areas

Science.gov (United States)

This is a presentation on the basics of green roof technology. The presentation highlights some of the recent ORD research projects on green roofs and provides insight for the end user as to the benefits for green roof technology. It provides links to currently available EPA rep...

Green electricity buyer's guide

International Nuclear Information System (INIS)

Kelly, B.; Klein, S.; Olivastri, B.

2002-06-01

The electricity produced in whole or in large part from renewable energy sources like wind, small hydro electricity and solar energy, is generally referred to as green electricity. The authors designed this buyer's guide to assist customers in their understanding of green electricity, as the customers can now choose their electricity supplier. The considerations and steps involved in the purchasse of green electricity are identified, and advice is provided on ways to maximize the benefits from the purchase of green electricity. In Alberta and Ontario, customers have access to a competitive electricity market. The emphasis when developing this guide was placed firmly on the large buyers, as they can have enormous positive influence on the new market for green electricity. The first chapter of the document provides general information on green electricity. In chapter two, the authors explore the opportunity for environmental leadership. Chapter three reviews the basics of green electricity, which provides the link to chapter four dealing with the creation of a policy. Purchasing green electricity is dealt with in Chapter five, and maximizing the benefits of green electricity are examined in Chapter Six. 24 refs., 3 tabs

Heat and mass transfer for turbulent flow of chemically reacting gas in eccentric annular channels

International Nuclear Information System (INIS)

Besedina, T.V.; Tverkovkin, B.E.; Udot, A.V.; Yakushev, A.P.

1988-01-01

Because of the possibility of using dissociating gases as coolants and working bodies of nuclear power plants, it is necessary to develop computational algorithms for calculating heat and mass transfer processes under conditions of nonequilibrium flow of chemically reacting gases not only in axisymmetric channels, but also in channels with a complex transverse cross section (including also in eccentric annular channels). An algorithm is proposed for calculating the velocity, temperature, and concentration fields under conditions of cooling of a cylindrical heat-releasing rod, placed off-center in a circular casing pipe, by a longitudinal flow of chemically reacting gas [N 2 O 4

The synergy in green persuasion: Green celebrity endorsers in green advertising: A study of brand-endorser congruence effects in green advertising

NARCIS (Netherlands)

Blasche, J.; Ketelaar, P.E.

2015-01-01

This study examines celebrity endorser-brand congruence effects in green advertising on the ads' effectiveness. In an experimental survey, Dutch participants (197) saw ads with a congruent or incongruent celebrity endorser. Extending the match-up hypothesis to a novel match-up factor, greenness, the

May compact storage facilities be licensed

International Nuclear Information System (INIS)

Gleim, A.; Winter, G.

1980-01-01

The authors examine as potential statements fo fact for licensing so-called compact storage facilities for spent fuel elements Sec. 6 to 9c of the German Atomic Energy Act and Sec. 4 of the German Radiation Protection Ordinance. They find that none of these provisions were applicable to compact stroage facilities. In particular, the storage of spent fuel elements was no storage of nuclear fuels licensable under Sec. 6 of the Atomic Energy Act, because Sec. 6 did not cover spent fuel elements. Also in the other wording of the Atomic Energy Act there was no provision, which could be used as a statement of fact for licensing compact storage facilities. Such facilities could not be licensed and, for that reason, were not permitted. (IVR) [de

Assessment of soil compaction properties based on surface wave techniques

Science.gov (United States)

Jihan Syamimi Jafri, Nur; Rahim, Mohd Asri Ab; Zahid, Mohd Zulham Affandi Mohd; Faizah Bawadi, Nor; Munsif Ahmad, Muhammad; Faizal Mansor, Ahmad; Omar, Wan Mohd Sabki Wan

2018-03-01

Soil compaction plays an important role in every construction activities to reduce risks of any damage. Traditionally, methods of assessing compaction include field tests and invasive penetration tests for compacted areas have great limitations, which caused time-consuming in evaluating large areas. Thus, this study proposed the possibility of using non-invasive surface wave method like Multi-channel Analysis of Surface Wave (MASW) as a useful tool for assessing soil compaction. The aim of this study was to determine the shear wave velocity profiles and field density of compacted soils under varying compaction efforts by using MASW method. Pre and post compaction of MASW survey were conducted at Pauh Campus, UniMAP after applying rolling compaction with variation of passes (2, 6 and 10). Each seismic data was recorded by GEODE seismograph. Sand replacement test was conducted for each survey line to obtain the field density data. All seismic data were processed using SeisImager/SW software. The results show the shear wave velocity profiles increase with the number of passes from 0 to 6 passes, but decrease after 10 passes. This method could attract the interest of geotechnical community, as it can be an alternative tool to the standard test for assessing of soil compaction in the field operation.

Reduction of malachite green to leucomalachite green by intestinal bacteria.

OpenAIRE

Henderson, A L; Schmitt, T C; Heinze, T M; Cerniglia, C E

1997-01-01

Intestinal microfloras from human, rat, mouse, and monkey fecal samples and 14 pure cultures of anaerobic bacteria representative of those found in the human gastrointestinal tract metabolized the triphenylmethane dye malachite green to leucomalachite green. The reduction of malachite green to the leuco derivative suggests that intestinal microflora could play an important role in the metabolic activation of the triphenylmethane dye to a potential carcinogen.

Compact accelerator for medical therapy

Science.gov (United States)

Caporaso, George J.; Chen, Yu-Jiuan; Hawkins, Steven A.; Sampayan, Stephen E.; Paul, Arthur C.

2010-05-04

A compact accelerator system having an integrated particle generator-linear accelerator with a compact, small-scale construction capable of producing an energetic (.about.70-250 MeV) proton beam or other nuclei and transporting the beam direction to a medical therapy patient without the need for bending magnets or other hardware often required for remote beam transport. The integrated particle generator-accelerator is actuable as a unitary body on a support structure to enable scanning of a particle beam by direction actuation of the particle generator-accelerator.

Observational properties of compact groups of galaxies

International Nuclear Information System (INIS)

Hickson, P.

1990-01-01

Compact groups are small, relatively isolated, systems of galaxies with projected separations comparable to the diameters of the galaxies themselves. Two well-known examples are Stephan's Quintet (Stephan, 1877) and Seyfert's Sextet (Seyfert 1948a,b). In groups such as these, the apparent space density of galaxies approaches 10(exp 6) Mpc(sub -3), denser even than the cores of rich clusters. The apparent unlikeliness of the chance occurrence of such tight groupings lead Ambartsumyan (1958, 1975) to conclude that compact groups must be physically dense systems. This view is supported by clear signs of galaxy interactions that are seen in many groups. Spectroscopic observations reveal that typical relative velocities of galaxies in the groups are comparable to their internal stellar velocities. This should be conducive to strong gravitational interactions - more so than in rich clusters, where galaxy velocities are typically much higher. This suggests that compact groups could be excellent laboratories in which to study galaxy interactions and their effects. Compact groups often contain one or more galaxies whose redshift differs greatly from those of the other group members. If these galaxies are at the same distance as the other members, either entire galaxies are being ejected at high velocities from these groups, or some new physical phenomena must be occurring. If their redshifts are cosmological, we must explain why so many discordant galaxies are found in compact groups. In recent years much progress has been made in addressing these questions. Here, the author discusses the current observational data on compact groups and their implications

Materials needs for compact fusion reactors

International Nuclear Information System (INIS)

Krakowski, R.A.

1983-01-01

The economic prospects for magnetic fusion energy can be dramatically improved if for the same total power output the fusion neutron first-wall (FW) loading and the system power density can be increased by factors of 3 to 5 and 10 to 30, respectively. A number of compact fusion reactor embodiments have been proposed, all of which would operate with increased FW loadings, would use thin (0.5 to 0.6 m) blankets, and would confine quasi-steady-state plasma with resistive, water-cooled copper or aluminum coils. Increased system power density (5 to 15 MWt/m 3 versus 0.3 to 0.5 MW/m 3 ), considerably reduced physical size of the fusion power core (FPC), and appreciably reduced economic leverage exerted by the FPC and associated physics result. The unique materials requirements anticipated for these compact reactors are outlined against the well documented backdrop provided by similar needs for the mainline approaches. Surprisingly, no single materials need that is unique to the compact systems is identified; crucial uncertainties for the compact approaches must also be addressed by the mainline approaches, particularly for in-vacuum components (FWs, limiters, divertors, etc.)

Considerations for evaluating proposed low-level radioactive waste compacts

International Nuclear Information System (INIS)

1985-02-01

Thirty-nine States have enacted legislation related to this Act, and five compacts have been submitted to Congress for consent. Other compacts are being negotiated, one in the West and several in the Midwest and Northeast. The Department of Energy has identified a number of items, which if included in the congressional review of each compact, would be likely to increase the possibility that new disposal sites will be developed and properly supported. The Department is providing additional perspectives that have not been previously included in testimony or reports. By suggesting examination of several general elements of a compact proposal, the Department hopes to provide a common focus that may be useful to the Congress in integrating all available information. The Department believes that the Congress should consider the following key items when reviewing the compacts: Commitments that assure the provision of new disposal capacity in the form of a host-State and site selection process with schedules and a target date for new sites to be opened; Commitments that provide short-term measures for storage, treatment, or disposal during an interim period when such new capacity may not be available; Consistency of definitions with 10 CFR Part 61 to assure the compact plan presents a total solution for all low-level waste generated within the region; Periodic review of the compacts by the Congress to examine concerns that are more easily assessed after a compact becomes operational, e.g., economic viability and long-term institutional control; and Economic viability of a compact, when reviewed in the future, in terms of the benefits and the costs specific to that region

Greening Steel Work: Varieties of Capitalism and the "Greening" of Skills

Science.gov (United States)

Evans, Claire; Stroud, Dean

2016-01-01

An important driver of change in work, employment and skills is European Union policy aims of sustainable economic growth and the cultivation of a green economy. Part of the latter--which is supported by increasing environmental regulation--focuses on the development of a "green skills agenda," which involves the "greening" of…

In the Green

Science.gov (United States)

Kennedy, Mike

2011-01-01

Education officials used to debate whether they could afford to pursue green design and construction. Now the green movement has gained a foothold not just in education, but in society at large, and the prevailing attitude seems to have shifted. Can schools afford "not" to go green? As budgets are slashed repeatedly, education administrators must…

Advantage of using high strength self compacting concrete for precast product

Science.gov (United States)

Murdono, Ferryandy; Agustin, Winda; Soeprapto, Gambiro; Sunarso, Mukhlis

2017-11-01

According to the development in the world of construction, the need for precast concrete also increases. Now the day there are many products with narrow range reinforcement and difficult dimensions. The ordinary concrete is difficult to pour in a mold with narrow range reinforcement inside without vibrator because the concrete can't fill in the gaps between the bars. SCC (Self Compacting Concrete) is a concrete that precast concrete industry needs to. The using of SCC also supports the green construction through the cement reducing and reducing the use of vibrator that requires not less energy. This research is using EFNARC standard as a condition of admission SCC (filling ability, passing ability, segregation resistance), and performed well against the application of the product by the production of Railway Sleeper without using a vibrator. The results of this study, the LB-2 and LB-3 qualified as SCC and compressive strength is expected that greater than 70 MPa, as well as products quality, is equal to standard and can be mass produced with the efficiency of the price of concrete up to 11%.

An innovative plate heat exchanger of enhanced compactness

International Nuclear Information System (INIS)

Vitillo, Francesco; Cachon, Lionel; Reulet, Philippe; Laroche, Emmanuel; Millan, Pierre

2015-01-01

In the framework of CEA R&D program to develop the Advanced Sodium Technological Reactor for Industrial Demonstration (ASTRID), the present work aims to demonstrate the industrial interest of an innovative compact heat exchanger technology. In fact, one of the main innovations of the ASTRID reactor could be the use of a Brayton Gas-power conversion system, in order to avoid the energetic sodium–water interaction that might occur if a traditional Rankine cycle was used. The present work aims to study the thermal-hydraulic performance of the innovative compact heat exchanger concept. Hence, thanks to a trustful numerical model, friction factor and heat transfer correlations are obtained. Then, a global compactness comparison strategy is proposed, taking into account design constraints. Finally, it is demonstrated that the innovative heat exchanger concept is more compact then other already industrial technologies of interest, showing that is can be considered to warrant serious consideration for future ASTRID design as well as for any industrial application that needs very compact heat exchanger technologies. - Highlights: • We propose a new innovative compact heat exchanger technology. • We provide thermal-hydraulic correlations for designers. • We provide a comparison strategy with existing technologies. • We demonstrate the industrial interest of the innovative concept

A Radiation Chemistry Code Based on the Greens Functions of the Diffusion Equation

Science.gov (United States)

Plante, Ianik; Wu, Honglu

2014-01-01

Ionizing radiation produces several radiolytic species such as.OH, e-aq, and H. when interacting with biological matter. Following their creation, radiolytic species diffuse and chemically react with biological molecules such as DNA. Despite years of research, many questions on the DNA damage by ionizing radiation remains, notably on the indirect effect, i.e. the damage resulting from the reactions of the radiolytic species with DNA. To simulate DNA damage by ionizing radiation, we are developing a step-by-step radiation chemistry code that is based on the Green's functions of the diffusion equation (GFDE), which is able to follow the trajectories of all particles and their reactions with time. In the recent years, simulations based on the GFDE have been used extensively in biochemistry, notably to simulate biochemical networks in time and space and are often used as the "gold standard" to validate diffusion-reaction theories. The exact GFDE for partially diffusion-controlled reactions is difficult to use because of its complex form. Therefore, the radial Green's function, which is much simpler, is often used. Hence, much effort has been devoted to the sampling of the radial Green's functions, for which we have developed a sampling algorithm This algorithm only yields the inter-particle distance vector length after a time step; the sampling of the deviation angle of the inter-particle vector is not taken into consideration. In this work, we show that the radial distribution is predicted by the exact radial Green's function. We also use a technique developed by Clifford et al. to generate the inter-particle vector deviation angles, knowing the inter-particle vector length before and after a time step. The results are compared with those predicted by the exact GFDE and by the analytical angular functions for free diffusion. This first step in the creation of the radiation chemistry code should help the understanding of the contribution of the indirect effect in the

Quantification of the compactibility of pharmaceutical powders

DEFF Research Database (Denmark)

Sonnergaard, Jørn

2006-01-01

The purpose of this study is to investigate and to quantify the compactibility of pharmaceutical powders by a simple linear relationship between the diametral compressive strength of tablets and the applied compaction pressure. The mechanical strength of the tablets is characterized as the crushing...

The green dilemma: Reflections of a Generation Y consumer cohort on green purchase behaviour

Directory of Open Access Journals (Sweden)

A. Muposhi

2015-12-01

Full Text Available Green consumerism has garnered much scholarly interest in recent years. However, research on the influence of the Social Dilemma Theory (SDT on green purchase behaviour has been scarce. Using data generated from sixteen in-depth-interviews, the present study identified perceived efficacy, perceived cost, in-group and self-identity, trust and peer influence as the main antecedents of SDT that influence green purchase behaviour. The findings of the study imply that to promote and institutionalise green purchase behaviour, marketers need to enhance perceived efficacy, trust in green products, reduce perceived cost, align green products with the consumers’ sought image and utilise peer networks when structuring green marketing messages.

Compact stellarators as reactors

International Nuclear Information System (INIS)

Lyon, J.F.; Valanju, P.; Zarnstorff, M.C.; Hirshman, S.; Spong, D.A.; Strickler, D.; Williamson, D.E.; Ware, A.

2001-01-01

Two types of compact stellarators are examined as reactors: two- and three-field-period (M=2 and 3) quasi-axisymmetric devices with volume-average =4-5% and M=2 and 3 quasi-poloidal devices with =10-15%. These low-aspect-ratio stellarator-tokamak hybrids differ from conventional stellarators in their use of the plasma-generated bootstrap current to supplement the poloidal field from external coils. Using the ARIES-AT model with B max =12T on the coils gives Compact Stellarator reactors with R=7.3-8.2m, a factor of 2-3 smaller R than other stellarator reactors for the same assumptions, and neutron wall loadings up to 3.7MWm -2 . (author)

Compact Spreader Schemes

Energy Technology Data Exchange (ETDEWEB)

Placidi, M.; Jung, J. -Y.; Ratti, A.; Sun, C.

2014-07-25

This paper describes beam distribution schemes adopting a novel implementation based on low amplitude vertical deflections combined with horizontal ones generated by Lambertson-type septum magnets. This scheme offers substantial compactness in the longitudinal layouts of the beam lines and increased flexibility for beam delivery of multiple beam lines on a shot-to-shot basis. Fast kickers (FK) or transverse electric field RF Deflectors (RFD) provide the low amplitude deflections. Initially proposed at the Stanford Linear Accelerator Center (SLAC) as tools for beam diagnostics and more recently adopted for multiline beam pattern schemes, RFDs offer repetition capabilities and a likely better amplitude reproducibility when compared to FKs, which, in turn, offer more modest financial involvements both in construction and operation. Both solutions represent an ideal approach for the design of compact beam distribution systems resulting in space and cost savings while preserving flexibility and beam quality.

Is green economy achievable through championing green growth? A local government experience from Zambia

Directory of Open Access Journals (Sweden)

Phiri Rodgers

2016-03-01

Full Text Available The need to enhance environmental sustainability, sustainable development and growth that takes into account the well-being of the people and nature because of the increased production and consumption of goods and services is the major driver to the introduction of green economy in Zambia and countries in southern Africa. This article examines the extent to which local government in Zambia has embraced green growth and green economy and critically analyses the concept of green economy and green growth. This study is based on a review of planning and policy documents, a household questionnaire survey and interviews with various institutions, planners and rural development organisations. A number of policies implemented at the local government level were analysed and reflected upon irrespective of whether they contain the components of green growth and green economy and the extent to which they contribute to attaining green economy. The article argues that the need for economic diversification is important as far as green economy is concerned. The article recommends the need to invest in research and development in order to find more carbon-free economic activities. The conclusion is that local government is key to achieving green growth and green economy, because it is involved at all levels, from policy formulation to implementation.

Green roof Malta

OpenAIRE

Gatt, Antoine

2015-01-01

In Malta, buildings cover one third of the Island, leaving greenery in the dirt track. Green roofs are one way to bring plants back to urban areas with loads of benefits. Antoine Gatt, who manages the LifeMedGreenRoof project at the University of Malta, tells us more. http://www.um.edu.mt/think/green-roof-malta/

IgE antibodies of fish allergic patients cross-react with frog parvalbumin.

Science.gov (United States)

Hilger, C; Thill, L; Grigioni, F; Lehners, C; Falagiani, P; Ferrara, A; Romano, C; Stevens, W; Hentges, F

2004-06-01

The major allergens in fish are parvalbumins. Important immunoglobulin (Ig)E cross-recognition of parvalbumins from different fish species has been shown. Recently frog parvalbumin alpha has been found to be responsible for a case of IgE-mediated anaphylaxis triggered by the ingestion of frog meat. The aim of this study was to investigate whether IgE antibodies of fish allergic persons cross-react with frog parvalbumin and to appreciate its clinical relevance. The sera of 15 fish allergic patients and one fish and frog allergic patient were tested by IgE-immunoblotting against frog muscle extract. Sera were tested against recombinant parvalbumin alpha and beta from Rana esculenta. Skin prick tests were performed in selected patients with recombinant frog parvalbumin. Ca(2+) depletion experiments and inhibition studies with purified cod and frog recombinant parvalbumin were done to characterize the cross-reactive pattern. Fourteen of the sera tested had IgE antibodies recognizing low molecular weight components in frog muscle extract. Calcium depletion experiments or inhibition of patient sera with purified cod parvalbumin led to a significant or complete decrease in IgE binding. When tested against recombinant parvalbumins, three of 13 sera reacted with alpha parvalbumin and 11 of 12 reacted with beta parvalbumin from R. esculenta. Skin prick tests performed with recombinant frog parvalbumin were positive in fish allergic patients. Inhibition studies showed that a fish and frog allergic patient was primarily sensitized to fish parvalbumin. Cod parvalbumin, a major cross-reactive allergen among different fish species, shares IgE binding epitopes with frog parvalbumin. This in vitro cross-reactivity seems to be also clinically relevant. Parvalbumins probably represent a new family of cross-reactive allergens.

Methods of making high performance compacts and products

International Nuclear Information System (INIS)

Fey, M.G.; Iyer, N.C.; Male, A.T.; Lovic, W.R.

1990-01-01

This patent describes a method of forming a pressed, dense compact. It comprises: providing a compactable particulate combination of: Class 1 metals selected from the group consisting of Ag, Cu, Al, and mixtures thereof, with material selected from the class consisting of CdO, SnO, SnO 2 , C, Co, Ni, Fe, Cr, Cr 3 C 2 , Cr 7 C 3 , W, WC, W 2 C, WB, Mo, Mo 2 C, MoB, Mo 2 B, TiC, TiN, TiB 2 , Si, SiC, Si 3 N 4 , and mixtures thereof; uniaxially pressing the particulate combination to provide a compact; placing at least one compact in an open pan; evacuating air from the pan; sealing the open top portion of the pan; stacking the pans next to each other, with plates having a high electrical resistance disposed between each pan so that the pans and plates alternate with each other, where a layer of thermally conductive, granular, pressure transmitting material is disposed between each pan and plate, which granular material acts to provide heat transfer and uniform mechanical loading to the compacts in the pans upon subsequent pressing; placing the stack in a press, passing an electrical current through the pans and high electrical resistance plates to cause a heating effect on the compacts in the pans, and uniaxial pressing the alternating pans and plates; cooling and releasing pressure on the alternating pans and plates; and separating the pans from the plates and the compacts from the pans

Dissolution and compaction instabilities in geomaterials

Science.gov (United States)

Stefanou, I.; Sulem, J.; de Sauvage, J.

2014-12-01

Compaction bands play an important role in reservoir engineering and geological storage. Their presence in geological formations may also provide useful information on various geological processes. Several mechanisms can be involved at different scales and may be responsible for compaction band instabilities [1]. Compaction bands can be seen as a particular instability of the governing mathematical system leading to localization of deformation [2-4]. In a saturated porous rock, the progressive mechanical damage of the solid skeleton during compaction, results in the increase of the interface area of the reactants and consequently in the acceleration of the dissolution rate of the solid phase [2,5]. Thus, the solid skeleton is degraded more rapidly (mass removal because of dissolution), the overall mechanical properties of the system diminish (contraction of the elastic domain - chemical softening), deformations increase and the solid skeleton is further damaged (intergranular fractures, debonding, breakage of the porous network etc.). The stability of this positive feedback process is investigated analytically through linear stability analysis by considering the strong chemo-poro-mechanical coupling due to chemical dissolution. The post bifurcation behavior is then studied analytically and numerically revealing the compaction band thickness and periodicity. The effect of various parameters is studied as for instance the influence of the hydraulic diffusivity on the compaction band thickness. [1] P. Baud, S. Vinciguerra, C. David, A. Cavallo, E. Walker and T. Reuschlé (2009), Pure Appl. Geophys., 166(5-7), 869-898 [2] I. Stefanou and J. Sulem (2014), JGR: Solid Earth, 119(2), 880-899. doi:10.1002/2013JB010342I [3] J.W. Rudnicki and J.R. Rice (1975), Journal of the Mechanics and Physics of Solids 23(6),: 371-394 [4] K.A. Issen and J.W. Rudnicki (2000), JGR, 105(B9), 21529. doi:10.1029/2000JB900185 [5] R. Nova, R. Castellanza and C. Tamagnini (2003), International

The classification of p-compact groups for p odd

DEFF Research Database (Denmark)

Andersen, Kasper K. S.; Grodal, Jesper Kragh; Møller, Jesper Michael

2008-01-01

A p-compact group, as defined by Dwyer and Wilkerson, is a purely homotopically defined p-local analog of a compact Lie group. It has long been the hope, and later the conjecture, that these objects should have a classification similar to the classification of compact Lie groups. In this paper we...... groups are uniquely determined as p-compact groups by their Weyl groups seen as finite reflection groups over the p-adic integers. Our approach in fact gives a largely self-contained proof of the entire classification theorem for p odd....

Can Culture Act as an Enabler to Innovation? Exploring the Germany-Ontario Experience Regarding the Introduction of Green Energy

Directory of Open Access Journals (Sweden)

Bill Irwin

2015-02-01

Full Text Available This paper explores the role that societal culture may play in terms of acting as an inhibitor or enabler when creating conditions conducive to innovative enterprise. To further understanding of this concept, the paper's authors explore different cultural influences and traditions of the country of Germany and the Canadian province of Ontario against the backdrop of the introduction of a government green energy policy and how local business reacts to new opportunities forthcoming from this shift in policy direction. The authors contend that the current Ontario psyche has contributed to an overall cultural drag on innovative activities. They demonstrate that in no place is this cultural impact more evident than the apparent lack of home-grown innovative activity surrounding green energy entrepreneurship; where, in spite of progressive and favourable provincial government policy, continued manufacturing growth is led by offshore companies The Ontario experience is in sharp contrast to current and historical German activity, when it comes to local innovation and advances in green energy. While Germany officially enacted their green energy act at the turn of the last century, experts agree that the German tenure with going green is in fact 35 to 40 years in the making. Although it has been contended that unique historical conditions such as postwar reconstruction and the reunification of the former East and West Germany have been significant contributing factors to Germany's embracing of sustainable energy, the authors of this paper contend that cultural factors such as the German sense of naturfreund; an overwhelming sense of being a nature-lover, may also play a significant role. In their exploration the authors build upon Hofstede's cultural dimension theory unpacking specific cultural components, as they compare actions and responses made by German and Ontarian policy-makers and business decision-makers.

Computing Decoupled Residuals for Compact Disc Players

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Stoustrup, Jakob; Andersen, Palle

2006-01-01

a pair of residuals generated by Compact Disc Player. However, these residuals depend on the performance of position servos in the Compact Disc Player. In other publications of the same authors a pair of decoupled residuals is derived. However, the computation of these alternative residuals has been...

Relationship between green marketing strategies and green marketing credibility among Generation Y

OpenAIRE

Garcia Sandoval, Michelle Haeberli; Manon Padilla, Alejandro

2016-01-01

Since terms like “sustainability” and “consumer consciousness” were introduced, green products began being integrated into consumers’ lifestyles. But due to the greenwashing practices that took place during the 90’s consumers refrain to buy green products because they do not trust the advertising released by marketers. The purpose of this thesis is to explore the relationship between green advertising credibility (dependent variable) and price sensitiveness, and the four proposed green market...

Professional Windows Embedded Compact 7

CERN Document Server

Phung, Samuel; Joubert, Thierry; Hall, Mike

2011-01-01

Learn to program an array of customized devices and solutions As a compact, highly efficient, scalable operating system, Windows Embedded Compact 7 (WEC7) is one of the best options for developing a new generation of network-enabled, media-rich, and service-oriented devices. This in-depth resource takes you through the benefits and capabilities of WEC7 so that you can start using this performance development platform today. Divided into several major sections, the book begins with an introduction and then moves on to coverage of OS design, application development, advanced application developm

Modeling of compact loop antennas

International Nuclear Information System (INIS)

Baity, F.W.

1987-01-01

A general compact loop antenna model which treats all elements of the antenna as lossy transmission lines has been developed. In addition to capacitively-tuned resonant double loop (RDL) antennas the model treats stub-tuned resonant double loop antennas. Calculations using the model have been compared with measurements on full-scale mockups of resonant double loop antennas for ATF and TFTR in order to refine the transmission line parameters. Results from the model are presented for RDL antenna designs for ATF, TFTR, Tore Supra, and for the Compact Ignition Tokamak

Challenges: a state and compact perspective

International Nuclear Information System (INIS)

Brown, H.

1987-01-01

The challenges facing states and compacts in their efforts to implement the Low-Level Waste Policy Amendments Act are described. Institutional challenges include: small-volume sites; compact maintenance; shifting agencies and changing personnel; and timing of progress. The technical challenge lies in the enormous number of plans, procedures, and regulations that have to be developed over the next four years. There are two main fiscal challenges: funding of day-to-day operations of compact commissions; and financing the siting and construction of new disposal sites. There are also two main regulatory challenges: host states must develop regulations for siting and selection of technology; and all states have to await federal regulations to be completed. The final challenge is political: whether a region can overcome public opposition and actually site a facility

Design study of the compact ERL

International Nuclear Information System (INIS)

Hajima, Ryoichi; Nakamura, Norio; Sakanaka, Shogo; Kobayashi, Yukinori

2008-02-01

Energy-recovery linac (ERL) is a promising device for future X-ray light sources, which can produce coherent X-rays and femto-second X-ray pulses. In Japan, we have organized a collaboration team, consisting of the members of KEK, JAEA, ISSP and other laboratories, toward realization of future ERL light sources, and started R and D efforts to establish accelerator technologies relevant to the ERL light source. In order to demonstrate all the accelerator technologies working together, we have decided to build a small facility, the Compact ERL. This report presents a design study of the Compact ERL, which includes R and D issues for each accelerator component, studies on the beam dynamics, performance of the Compact ERL as a light source of THz and X-ray. (author)

{theta}-Compactness in L-topological spaces

Energy Technology Data Exchange (ETDEWEB)

Hanafy, I.M. [Department of Mathematics, Faculty of Education, Suez Canal University, El-Arish (Egypt)], E-mail: ihanafy@hotmail.com

2009-12-15

Recently, El-Naschie has shown that the notion of fuzzy topology may be relevant to quantum particle physics in connection with string theory and e{sup {infinity}} theory. In 2005, Caldas and Jafari have introduced {theta}-compact fuzzy topological spaces. In this paper, the concepts of{theta}-compactness, countable{theta}-compactness and the{theta}-Lindeloef property are introduced and studied in L-topological spaces, where L is a complete de Morgan algebra. They are defined by means of{theta}-openL-sets and their inequalities. They does not rely on the structure of basis lattice L and no distributivity in L is required. They can also be characterized by{theta}-closedL-sets and their inequalities. When L is a completely de Morgan algebra, their many characterizations are presented.

Rapid solidification and dynamic compaction of Ni-base superalloy powders

Science.gov (United States)

Field, R. D.; Hales, S. J.; Powers, W. O.; Fraser, H. L.

1984-01-01

A Ni-base superalloy containing 13Al-9Mo-2Ta (in at. percent) has been characterized in both the rapidly solidified condition and after dynamic compaction. Dynamically compacted specimens were examined in the as-compacted condition and observations related to current theories of interparticle bonding. In addition, the recrystallization behavior of the compacted material at relatively low temperature (about 0.5-0.75 Tm) was investigated.

New geometrical compactness measures for zones design

Directory of Open Access Journals (Sweden)

Eric Alfredo Rincón-García

2012-07-01

Full Text Available The design of compact zones has been studied because of its influence in the creation of zones with regular forms, which are easier to analyze, to investigate or to administer. This paper propose a new method to measure compactness,by means of the transformation of the original geographical spaces, into figures formed with square cells, which are used to measure the similarity between the original zone and an ideal zone with straight forms. The proposed method was applied to design electoral zones, which must satisfy constraints of compactness, contiguity and population balance, in a topographical configuration that favors the creation of twisted and diffuse shapes. The results show that the new method favors the creation of zones with straight forms, without an important effect to the population balance, which are considered zones of high quality. Keywords: Redistricting, compactness, simulated annealing, GIS. Mathematics Subject Classification: 90C59, 90C29, 68T20.

Non-compact left ventricle/hypertrabeculated left ventricle

International Nuclear Information System (INIS)

Restrepo, Gustavo; Castano, Rafael; Marmol, Alejandro

2005-01-01

Non-compact left ventricle/hypertrabeculated left ventricle is a myocardiopatie produced by an arrest of the normal left ventricular compaction process during the early embryogenesis. It is associated to cardiac anomalies (congenital cardiopaties) as well as to extracardial conditions (neurological, facial, hematologic, cutaneous, skeletal and endocrinological anomalies). This entity is frequently unnoticed, being diagnosed only in centers with great experience in the diagnosis and treatment of myocardiopathies. Many cases of non-compact left ventricle have been initially misdiagnosed as hypertrophic myocardiopatie, endocardial fibroelastosis, dilated cardiomyopatie, restrictive cardiomyopathy and endocardial fibrosis. It is reported the case of a 74 years old man with a history of chronic arterial hypertension and diabetes mellitus, prechordial chest pain and mild dyspnoea. An echocardiogram showed signs of non-compact left ventricle with prominent trabeculations and deep inter-trabecular recesses involving left ventricular apical segment and extending to the lateral and inferior walls. Literature on this topic is reviewed

Green Roofs and Green Walls for Biodiversity Conservation: A Contribution to Urban Connectivity?

Directory of Open Access Journals (Sweden)

Flavie Mayrand

2018-03-01

Full Text Available Green roofs and walls have recently emerged as conservation tools, and they offer promising additional opportunities to enhance biodiversity in cities. However, their ecological conditions remain poorly considered when planning wildlife corridors. To discuss the role of vegetated buildings in landscape connectivity, we reviewed the ecological and technical specificities of green walls and green roofs in light of the key factors concerning urban wildlife (patch size, quality, abundance, and isolation. Green roofs and walls show limited patch sizes, distinct habitat quality at the building scale, and limited redundancy of patch quality within the landscape. We also highlight that the abundance of roof and wall patches is often low. Future research is needed to establish if walls can be vertical corridors for wildlife, thereby reducing the isolation of green roofs. We argue that creating 3D ecological connectivity within the city requires substantial modifications of the design and maintenance of existing green building systems. We suggest that research is needed to integrate the biotic and abiotic characteristics of green buildings to make them more closely resemble those of open green spaces.

Modeling the NPE with finite sources and empirical Green`s functions

Energy Technology Data Exchange (ETDEWEB)

Hutchings, L.; Kasameyer, P.; Goldstein, P. [Lawrence Livermore National Lab., CA (United States)] [and others

1994-12-31

In order to better understand the source characteristics of both nuclear and chemical explosions for purposes of discrimination, we have modeled the NPE chemical explosion as a finite source and with empirical Green`s functions. Seismograms are synthesized at four sties to test the validity of source models. We use a smaller chemical explosion detonated in the vicinity of the working point to obtain empirical Green`s functions. Empirical Green`s functions contain all the linear information of the geology along the propagation path and recording site, which are identical for chemical or nuclear explosions, and therefore reduce the variability in modeling the source of the larger event. We further constrain the solution to have the overall source duration obtained from point-source deconvolution results. In modeling the source, we consider both an elastic source on a spherical surface and an inelastic expanding spherical volume source. We found that the spherical volume solution provides better fits to observed seismograms. The potential to identify secondary sources was examined, but the resolution is too poor to be definitive.

Snowmelt runoff in the Green River basin derived from MODIS snow extent

Science.gov (United States)

Barton, J. S.; Hall, D. K.

2011-12-01

The Green River represents a vital water supply for southwestern Wyoming, northern Colorado, eastern Utah, and the Lower Colorado River Compact states (Arizona, Nevada, and California). Rapid development in the southwestern United States combined with the recent drought has greatly stressed the water supply of the Colorado River system, and concurrently increased the interest in long-term variations in stream flow. Modeling of snowmelt runoff represents a means to predict flows and reservoir storage, which is useful for water resource planning. An investigation is made into the accuracy of the Snowmelt Runoff Model of Martinec and Rango, driven by Moderate Resolution Imaging Spectroradiometer (MODIS) snow maps for predicting stream flow within the Green River basin. While the moderate resolution of the MODIS snow maps limits the spatial detail that can be captured, the daily coverage is an important advantage of the MODIS imagery. The daily MODIS snow extent is measured using the most recent clear observation for each 500-meter pixel. Auxiliary data used include temperature and precipitation time series from the Snow Telemetry (SNOTEL) and Remote Automated Weather Station (RAWS) networks as well as from National Weather Service records. Also from the SNOTEL network, snow-water equivalence data are obtained to calibrate the conversion between snow extent and runoff potential.

The skeptical green consumer revisited: testing the relationship between green consumerism and skepticism toward advertising

NARCIS (Netherlands)

Matthes, J.; Wonneberger, A.

2014-01-01

This article revisits the widely believed notion of the skeptical green consumer, in other words, that green consumers tend to distrust green advertising. Study 1, a survey of U.S. consumers, found no positive relationship between green consumerism and general ad skepticism. However, green

Development of a Reduced-Order Model for Reacting Gas-Solids Flow using Proper Orthogonal Decomposition

Energy Technology Data Exchange (ETDEWEB)

McDaniel, Dwayne [Florida International Univ., Miami, FL (United States); Dulikravich, George [Florida International Univ., Miami, FL (United States); Cizmas, Paul [Florida International Univ., Miami, FL (United States)

2017-11-27

This report summarizes the objectives, tasks and accomplishments made during the three year duration of this research project. The report presents the results obtained by applying advanced computational techniques to develop reduced-order models (ROMs) in the case of reacting multiphase flows based on high fidelity numerical simulation of gas-solids flow structures in risers and vertical columns obtained by the Multiphase Flow with Interphase eXchanges (MFIX) software. The research includes a numerical investigation of reacting and non-reacting gas-solids flow systems and computational analysis that will involve model development to accelerate the scale-up process for the design of fluidization systems by providing accurate solutions that match the full-scale models. The computational work contributes to the development of a methodology for obtaining ROMs that is applicable to the system of gas-solid flows. Finally, the validity of the developed ROMs is evaluated by comparing the results against those obtained using the MFIX code. Additionally, the robustness of existing POD-based ROMs for multiphase flows is improved by avoiding non-physical solutions of the gas void fraction and ensuring that the reduced kinetics models used for reactive flows in fluidized beds are thermodynamically consistent.

MHD flow and heat transfer of a viscous reacting fluid over a ...

African Journals Online (AJOL)

This paper presents a boundary layer flow analysis for a viscous, incompressible, electrically conducting reacting fluid over a stretching sheet in the presence of a magnetic field. It is shown that the Hartmann, Prandtl and the Eckert numbers have effect on the velocity and temperature fields. Journal of the Nigerian ...

Green Mind Theory: How Brain-Body-Behaviour Links into Natural and Social Environments for Healthy Habits

Directory of Open Access Journals (Sweden)

Jules Pretty

2017-06-01

Full Text Available We propose a Green Mind Theory (GMT to link the human mind with the brain and body, and connect the body into natural and social environments. The processes are reciprocal: environments shape bodies, brains, and minds; minds change body behaviours that shape the external environment. GMT offers routes to improved individual well-being whilst building towards greener economies. It builds upon research on green exercise and nature-based therapies, and draws on understanding derived from neuroscience and brain plasticity, spiritual and wisdom traditions, the lifeways of original cultures, and material consumption behaviours. We set out a simple metaphor for brain function: a bottom brain stem that is fast-acting, involuntary, impulsive, and the driver of fight and flight behaviours; a top brain cortex that is slower, voluntary, the centre for learning, and the driver of rest and digest. The bottom brain reacts before thought and directs the sympathetic nervous system. The top brain is calming, directing the parasympathetic nervous system. Here, we call the top brain blue and the bottom brain red; too much red brain is bad for health. In modern high-consumption economies, life has often come to be lived on red alert. An over-active red mode impacts the gastrointestinal, immune, cardiovascular, and endocrine systems. We develop our knowledge of nature-based interventions, and suggest a framework for the blue brain-red brain-green mind. We show how activities involving immersive-attention quieten internal chatter, how habits affect behaviours across the lifecourse, how long habits take to be formed and hard-wired into daily practice, the role of place making, and finally how green minds could foster prosocial and greener economies. We conclude with observations on twelve research priorities and health interventions, and ten calls to action.

Green Mind Theory: How Brain-Body-Behaviour Links into Natural and Social Environments for Healthy Habits.

Science.gov (United States)

Pretty, Jules; Rogerson, Mike; Barton, Jo

2017-06-30

We propose a Green Mind Theory (GMT) to link the human mind with the brain and body, and connect the body into natural and social environments. The processes are reciprocal: environments shape bodies, brains, and minds; minds change body behaviours that shape the external environment. GMT offers routes to improved individual well-being whilst building towards greener economies. It builds upon research on green exercise and nature-based therapies, and draws on understanding derived from neuroscience and brain plasticity, spiritual and wisdom traditions, the lifeways of original cultures, and material consumption behaviours. We set out a simple metaphor for brain function: a bottom brain stem that is fast-acting, involuntary, impulsive, and the driver of fight and flight behaviours; a top brain cortex that is slower, voluntary, the centre for learning, and the driver of rest and digest. The bottom brain reacts before thought and directs the sympathetic nervous system. The top brain is calming, directing the parasympathetic nervous system. Here, we call the top brain blue and the bottom brain red; too much red brain is bad for health. In modern high-consumption economies, life has often come to be lived on red alert. An over-active red mode impacts the gastrointestinal, immune, cardiovascular, and endocrine systems. We develop our knowledge of nature-based interventions, and suggest a framework for the blue brain-red brain-green mind. We show how activities involving immersive-attention quieten internal chatter, how habits affect behaviours across the lifecourse, how long habits take to be formed and hard-wired into daily practice, the role of place making, and finally how green minds could foster prosocial and greener economies. We conclude with observations on twelve research priorities and health interventions, and ten calls to action.

Compaction and relaxation of biofilms

KAUST Repository

Valladares Linares, R.

2015-06-18

Operation of membrane systems for water treatment can be seriously hampered by biofouling. A better characterization of biofilms in membrane systems and their impact on membrane performance may help to develop effective biofouling control strategies. The objective of this study was to determine the occurrence, extent and timescale of biofilm compaction and relaxation (decompaction), caused by permeate flux variations. The impact of permeate flux changes on biofilm thickness, structure and stiffness was investigated in situ and non-destructively with optical coherence tomography using membrane fouling monitors operated at a constant crossflow velocity of 0.1 m s−1 with permeate production. The permeate flux was varied sequentially from 20 to 60 and back to 20 L m−2 h−1. The study showed that the average biofilm thickness on the membrane decreased after elevating the permeate flux from 20 to 60 L m−2 h−1 while the biofilm thickness increased again after restoring the original flux of 20 L m−2 h−1, indicating the occurrence of biofilm compaction and relaxation. Within a few seconds after the flux change, the biofilm thickness was changed and stabilized, biofilm compaction occurred faster than the relaxation after restoring the original permeate flux. The initial biofilm parameters were not fully reinstated: the biofilm thickness was reduced by 21%, biofilm stiffness had increased and the hydraulic biofilm resistance was elevated by 16%. Biofilm thickness was related to the hydraulic biofilm resistance. Membrane performance losses are related to the biofilm thickness, density and morphology, which are influenced by (variations in) hydraulic conditions. A (temporarily) permeate flux increase caused biofilm compaction, together with membrane performance losses. The impact of biofilms on membrane performance can be influenced (increased and reduced) by operational parameters. The article shows that a (temporary) pressure increase leads to more

Green Campus initiative and its impacts on quality of life of stakeholders in Green and Non-Green Campus universities.

Science.gov (United States)

Tiyarattanachai, Ronnachai; Hollmann, Nicholas M

2016-01-01

In 2010, Universitas Indonesia (UI) developed the UI GreenMetric World University Ranking for universities to share information about their sustainability practices. This ranking system was well aligned with the basis of Sustainability for Higher Education. The scoring system can also be used as a guideline for universities to achieve sustainability in their campuses. Since its first launch, more universities around the world have increasingly participated in the ranking system including many universities in Thailand. This study compared perception of stakeholders in Green Campus and Non-Green Campus universities in Thailand regarding stakeholders' satisfaction on sustainability practices and perceived quality of life at their campuses. The results showed that stakeholders at the studied Green Campus University were more satisfied and had significantly better perceived quality of life compared to stakeholders from the studied Non-Green Campus university. The results suggested that universities should adopt the criteria set in the UI GreenMetric World University Ranking to achieve better sustainability in their campuses and improve quality of life of their stakeholders.

Propel: A Discontinuous-Galerkin Finite Element Code for Solving the Reacting Navier-Stokes Equations

Science.gov (United States)

Johnson, Ryan; Kercher, Andrew; Schwer, Douglas; Corrigan, Andrew; Kailasanath, Kazhikathra

2017-11-01

This presentation focuses on the development of a Discontinuous Galerkin (DG) method for application to chemically reacting flows. The in-house code, called Propel, was developed by the Laboratory of Computational Physics and Fluid Dynamics at the Naval Research Laboratory. It was designed specifically for developing advanced multi-dimensional algorithms to run efficiently on new and innovative architectures such as GPUs. For these results, Propel solves for convection and diffusion simultaneously with detailed transport and thermodynamics. Chemistry is currently solved in a time-split approach using Strang-splitting with finite element DG time integration of chemical source terms. Results presented here show canonical unsteady reacting flow cases, such as co-flow and splitter plate, and we report performance for higher order DG on CPU and GPUs.

The Green Man

Science.gov (United States)

Watson-Newlin, Karen

2010-01-01

The Jolly Green Giant. Robin Hood. The Bamberg Cathedral. Tales of King Arthur. Ecology. What do they have in common? What legends and ancient myths are shrouded in the tales of the Green Man? Most often perceived as an ancient Celtic symbol as the god of spring and summer, the Green Man disappears and returns year after year, century after…

Mechanical compaction of Waste Isolation Pilot Plant simulated waste

International Nuclear Information System (INIS)

Butcher, B.M.; Thompson, T.W.; VanBuskirk, R.G.; Patti, N.C.

1991-06-01

The investigation described in this report acquired experimental information about how materials simulating transuranic (TRU) waste compact under axial compressive stress, and used these data to define a model for use in the Waste Isolation Pilot Plant (WIPP) disposal room analyses. The first step was to determine compaction curves for various simultant materials characteristic of TRU waste. Stress-volume compaction curves for various combinations of these materials were than derived to represent the combustible, metallic, and sludge waste categories. Prediction of compaction response in this manner is considered essential for the WIPP program because of the difficulties inherent in working with real (radioactive) waste. Next, full-sized 55-gallon drums of simulated combustible, metallic, and sludge waste were axially compacted. These results provided data that can be directly applied to room consolidation and data for comparison with the predictions obtained in Part 1 of the investigation. Compaction curves, which represent the combustible, metallic, and sludge waste categories, were determined, and a curve for the averaged waste inventory of the entire repository was derived. 9 refs., 31 figs., 12 tabs

Duality results for co-compact Gabor systems

DEFF Research Database (Denmark)

Jakobsen, Mads Sielemann; Lemvig, Jakob

2015-01-01

In this paper we give an account of recent developments in the duality theory of Gabor frames. We prove the Wexler-Raz biorthogonality relations and the duality principle for co-compact Gabor systems on second countable, locally compact abelian groups G. Our presentation does not rely on the exis...

Why Targets of Economic Sanctions React Differently: Reference Point Effects on North Korea and Libya

Directory of Open Access Journals (Sweden)

Jiyoun Park

2017-06-01

Full Text Available The international community has frequently introduced economic sanctions to curb the proliferation of weapons of mass destruction, to which each target nation has reacted differently. This paper explores the reasons why each target of economic sanctions reacts differently by specif- ically building a model based on reference point effects, and by analyzing the cases of North Korea and Libya. According to the results, when the reference point level increases, as in the case of North Korea, the target resists more firmly; on the other hand, when the reference point decreases, like in the case of Libya, the target resists more subtly.

Green Buildings and Health.

Science.gov (United States)

Allen, Joseph G; MacNaughton, Piers; Laurent, Jose Guillermo Cedeno; Flanigan, Skye S; Eitland, Erika Sita; Spengler, John D

2015-09-01

Green building design is becoming broadly adopted, with one green building standard reporting over 3.5 billion square feet certified to date. By definition, green buildings focus on minimizing impacts to the environment through reductions in energy usage, water usage, and minimizing environmental disturbances from the building site. Also by definition, but perhaps less widely recognized, green buildings aim to improve human health through design of healthy indoor environments. The benefits related to reduced energy and water consumption are well-documented, but the potential human health benefits of green buildings are only recently being investigated. The objective of our review was to examine the state of evidence on green building design as it specifically relates to indoor environmental quality and human health. Overall, the initial scientific evidence indicates better indoor environmental quality in green buildings versus non-green buildings, with direct benefits to human health for occupants of those buildings. A limitation of much of the research to date is the reliance on indirect, lagging and subjective measures of health. To address this, we propose a framework for identifying direct, objective and leading "Health Performance Indicators" for use in future studies of buildings and health.

Fracture toughness measurements with subsize disk compact specimens

International Nuclear Information System (INIS)

Alexander, D.J.

1992-01-01

Special fixtures and test methods are necessary to facilitate the fracture toughness testing of small disk compact specimens of irradiated candidate materials for first-wall fusion applications. New methods have been developed for both the unloading compliance and potential drop techniques of monitoring crack growth. Provisions have been made to allow the necessary probes and instrumentation to be installed remotely using manipulators for testing of irradiated specimens in a hot cell. Laboratory trials showed that both unloading compliance and potential drop gave useful results. Both techniques gave similar data, and predicted the final crack extension within allowable limits. The results from the small disk compact specimens were similar to results from conventional compact specimen 12.7 mm thick. However, the slopes of the J-R curves from the larger specimens were lower, suggesting that the smaller disk compact specimens may have lost some constraint due to their size. The testing shows that it should be possible to generate useful J-R curve fracture toughness data from the small disk compact specimens

Fracture toughness measurements with subsize disk compact specimens

International Nuclear Information System (INIS)

Alexander, D.J.

1992-01-01

Special fixtures and test methods have been developed for testing small disk compact specimens (12.5 mm diam by 4.6 mm thick). Both unloading compliance and potential drop methods have been used to monitor crack extension during the J-integral resistance (J-R) curve testing. Provisions have been made to allow the necessary probes and instrumentation to be installed remotely using manipulators for testing of irradiated specimens in a hat cell. Laboratory trials showed that both unloading compliance and potential drop gave useful results. Both techniques gave similar data, and predicted the final crack extension within allowable limits. The results from the small disk compact specimens were similar to results from conventional compact specimens 12.7-mm thick. However, the slopes of the J-R curves from the larger specimens were lower, suggesting that the smaller disk compact specimens may have lost some constraint due to their size. The testing shows that it should be possible to generate useful J-R curve fracture toughness data from the small disk compact specimens

The Responsive Environmental Assessment for Classroom Teaching (REACT): the dimensionality of student perceptions of the instructional environment.

Science.gov (United States)

Nelson, Peter M; Demers, Joseph A; Christ, Theodore J

2014-06-01

This study details the initial development of the Responsive Environmental Assessment for Classroom Teachers (REACT). REACT was developed as a questionnaire to evaluate student perceptions of the classroom teaching environment. Researchers engaged in an iterative process to develop, field test, and analyze student responses on 100 rating-scale items. Participants included 1,465 middle school students across 48 classrooms in the Midwest. Item analysis, including exploratory and confirmatory factor analysis, was used to refine a 27-item scale with a second-order factor structure. Results support the interpretation of a single general dimension of the Classroom Teaching Environment with 6 subscale dimensions: Positive Reinforcement, Instructional Presentation, Goal Setting, Differentiated Instruction, Formative Feedback, and Instructional Enjoyment. Applications of REACT in research and practice are discussed along with implications for future research and the development of classroom environment measures. PsycINFO Database Record (c) 2014 APA, all rights reserved.

77 FR 24494 - Office of Federal High-Performance Green Buildings; Green Building Advisory Committee...

Science.gov (United States)

2012-04-24

... Federal High-Performance Green Buildings; Green Building Advisory Committee; Notification of Upcoming... agenda for the May 9, 2012, meeting of the Green Building Advisory Committee Meeting (the Committee). The... Sandler, Designated Federal Officer, Office of Federal High-Performance Green Buildings, Office of...

77 FR 66616 - Office of Federal High-Performance Green Buildings; Green Building Advisory Committee...

Science.gov (United States)

2012-11-06

... Federal High-Performance Green Buildings; Green Building Advisory Committee; Notification of Upcoming... and agenda for the November 27, 2012, meeting of the Green Building Advisory Committee Meeting (the... Green Buildings, Office of Government-wide Policy, General Services Administration, 1275 First Street NE...

78 FR 21368 - Office of Federal High-Performance Green Buildings; Green Building Advisory Committee...

Science.gov (United States)

2013-04-10

... Federal High-Performance Green Buildings; Green Building Advisory Committee; Notification of Upcoming... and agenda for the May 1, 2013, meeting of the Green Building Advisory Committee Meeting (the... Green Buildings, Office of Government-wide Policy, General Services Administration, 1275 First Street NE...

Gun-generated compact tori at Los Alamos

International Nuclear Information System (INIS)

Jarboe, T.R.; Henins, I.; Hoida, H.W.; Linford, R.K.; Marshall, J.; Platts, D.A.; Sherwood, A.R.

1982-01-01

We have generated compact toroids which can be made to come to rest in a cylindrical resistive flux conserver. They are observed to rotate so that their major axis is perpendicular to the axis of the flux conserver. Subsequently they appear to remain stationary and decay with a time constant of about 100 μs. We have also generated compact toroids in an oblate geometry which remain aligned with the axis of the flux conserver and decay with a time constant of 150 μs. The magnetic field reconnection time for compact toroid formation is measured in the latter case to be much shorter than the decay time

Strange matter in compact stars

Directory of Open Access Journals (Sweden)

Klähn Thomas

2018-01-01

Full Text Available We discuss possible scenarios for the existence of strange matter in compact stars. The appearance of hyperons leads to a hyperon puzzle in ab-initio approaches based on effective baryon-baryon potentials but is not a severe problem in relativistic mean field models. In general, the puzzle can be resolved in a natural way if hadronic matter gets stiffened at supersaturation densities, an effect based on the quark Pauli quenching between hadrons. We explain the conflict between the necessity to implement dynamical chiral symmetry breaking into a model description and the conditions for the appearance of absolutely stable strange quark matter that require both, approximately masslessness of quarks and a mechanism of confinement. The role of strangeness in compact stars (hadronic or quark matter realizations remains unsettled. It is not excluded that strangeness plays no role in compact stars at all. To answer the question whether the case of absolutely stable strange quark matter can be excluded on theoretical grounds requires an understanding of dense matter that we have not yet reached.

Strange matter in compact stars

Science.gov (United States)

Klähn, Thomas; Blaschke, David B.

2018-02-01

We discuss possible scenarios for the existence of strange matter in compact stars. The appearance of hyperons leads to a hyperon puzzle in ab-initio approaches based on effective baryon-baryon potentials but is not a severe problem in relativistic mean field models. In general, the puzzle can be resolved in a natural way if hadronic matter gets stiffened at supersaturation densities, an effect based on the quark Pauli quenching between hadrons. We explain the conflict between the necessity to implement dynamical chiral symmetry breaking into a model description and the conditions for the appearance of absolutely stable strange quark matter that require both, approximately masslessness of quarks and a mechanism of confinement. The role of strangeness in compact stars (hadronic or quark matter realizations) remains unsettled. It is not excluded that strangeness plays no role in compact stars at all. To answer the question whether the case of absolutely stable strange quark matter can be excluded on theoretical grounds requires an understanding of dense matter that we have not yet reached.

Durability of Self Compacting Concrete

International Nuclear Information System (INIS)

Benmarce, A.; Boudjehem, H.; Bendjhaiche, R.

2011-01-01

Self compacting concrete (SCC) seem to be a very promising materials for construction thanks to their properties in a fresh state. Studying of the influence of the parameters of specific designed mixes to their mechanical, physical and chemical characteristics in a state hardened is an important stage so that it can be useful for new-to-the-field researchers and designers (worldwide) beginning studies and work involving self compacting concrete. The objective of this research is to study the durability of self compacting concrete. The durability of concrete depends very much on the porosity; the latter determines the intensity of interactions with aggressive agents. The pores inside of concrete facilitate the process of damage, which began generally on the surface. We are interested to measure the porosity of concrete on five SCC with different compositions (w/c, additives) and vibrated concrete to highlight the influence of the latter on the porosity, thereafter on the compressive strength and the transfer properties (oxygen permeability, chloride ion diffusion, capillary absorption). (author)

Compaction Characteristics of Igumale Shale | Iorliam | Global ...

African Journals Online (AJOL)

This paper reports the outcome of an investigation into the effect of different compactive energies on the compaction characteristics of Igumale shale, to ascertain its suitability as fill material in highway ... The study showed that Igumale shale is not suitable for use as base, subbase and filling materials in road construction.

Dynamic compaction with high energy of sandy hydraulic fills

Directory of Open Access Journals (Sweden)

Khelalfa Houssam

2017-09-01

Full Text Available A case study about the adoption of the dynamic compaction technique with high energy in a sandy hydraulic fill is presented. The feasibility of this technique to ensure the stability of the caisson workshop and to minimize the risk of liquefaction during manufacture. This Article is interested to establish diagnostic of dynamic compaction test, basing on the results of SPT tests and quality control as well as the details of work of compaction and the properties of filling materials. A theory of soil response to a high-energy impact during dynamic compaction is proposed.

COSMIC probes into compact binary formation and evolution

Science.gov (United States)

Breivik, Katelyn

2018-01-01

The population of compact binaries in the galaxy represents the final state of all binaries that have lived up to the present epoch. Compact binaries present a unique opportunity to probe binary evolution since many of the interactions binaries experience can be imprinted on the compact binary population. By combining binary evolution simulations with catalogs of observable compact binary systems, we can distill the dominant physical processes that govern binary star evolution, as well as predict the abundance and variety of their end products.The next decades herald a previously unseen opportunity to study compact binaries. Multi-messenger observations from telescopes across all wavelengths and gravitational-wave observatories spanning several decades of frequency will give an unprecedented view into the structure of these systems and the composition of their components. Observations will not always be coincident and in some cases may be separated by several years, providing an avenue for simulations to better constrain binary evolution models in preparation for future observations.I will present the results of three population synthesis studies of compact binary populations carried out with the Compact Object Synthesis and Monte Carlo Investigation Code (COSMIC). I will first show how binary-black-hole formation channels can be understood with LISA observations. I will then show how the population of double white dwarfs observed with LISA and Gaia could provide a detailed view of mass transfer and accretion. Finally, I will show that Gaia could discover thousands black holes in the Milky Way through astrometric observations, yielding view into black-hole astrophysics that is complementary to and independent from both X-ray and gravitational-wave astronomy.

Sticky tunes: how do people react to involuntary musical imagery?

Directory of Open Access Journals (Sweden)

Victoria J Williamson

Full Text Available The vast majority of people experience involuntary musical imagery (INMI or 'earworms'; perceptions of spontaneous, repetitive musical sound in the absence of an external source. The majority of INMI episodes are not bothersome, while some cause disruption ranging from distraction to anxiety and distress. To date, little is known about how the majority of people react to INMI, in particular whether evaluation of the experience impacts on chosen response behaviours or if attempts at controlling INMI are successful or not. The present study classified 1046 reports of how people react to INMI episodes. Two laboratories in Finland and the UK conducted an identical qualitative analysis protocol on reports of INMI reactions and derived visual descriptive models of the outcomes using grounded theory techniques. Combined analysis carried out across the two studies confirmed that many INMI episodes were considered neutral or pleasant, with passive acceptance and enjoyment being among the most popular response behaviours. A significant number of people, however, reported on attempts to cope with unwanted INMI. The most popular and effective behaviours in response to INMI were seeking out the tune in question, and musical or verbal distraction. The outcomes of this study contribute to our understanding of the aetiology of INMI, in particular within the framework of memory theory, and present testable hypotheses for future research on successful INMI coping strategies.

Sticky Tunes: How Do People React to Involuntary Musical Imagery?

Science.gov (United States)

Williamson, Victoria J.; Liikkanen, Lassi A.; Jakubowski, Kelly; Stewart, Lauren

2014-01-01

The vast majority of people experience involuntary musical imagery (INMI) or ‘earworms’; perceptions of spontaneous, repetitive musical sound in the absence of an external source. The majority of INMI episodes are not bothersome, while some cause disruption ranging from distraction to anxiety and distress. To date, little is known about how the majority of people react to INMI, in particular whether evaluation of the experience impacts on chosen response behaviours or if attempts at controlling INMI are successful or not. The present study classified 1046 reports of how people react to INMI episodes. Two laboratories in Finland and the UK conducted an identical qualitative analysis protocol on reports of INMI reactions and derived visual descriptive models of the outcomes using grounded theory techniques. Combined analysis carried out across the two studies confirmed that many INMI episodes were considered neutral or pleasant, with passive acceptance and enjoyment being among the most popular response behaviours. A significant number of people, however, reported on attempts to cope with unwanted INMI. The most popular and effective behaviours in response to INMI were seeking out the tune in question, and musical or verbal distraction. The outcomes of this study contribute to our understanding of the aetiology of INMI, in particular within the framework of memory theory, and present testable hypotheses for future research on successful INMI coping strategies. PMID:24497938

Effect of material parameters on the compactibility of backfill materials

International Nuclear Information System (INIS)

Keto, P.; Kuula-Vaeisaenen, P.; Ruuskanen, J.

2006-05-01

The effect of different parameters on compactibility of mixture of bentonite and ballast as well as Friedland-clay was studied in laboratory with two different types of compaction tests. The material parameters varied were grain size distribution of the ballast material, grain shape, water ratio and bentonite content (15/30%). The other parameters varied were salinity of the mixing water, mixing process and compaction method and energy. Ballast materials with varying grain size distributions were produced from Olkiluoto mica-gneiss with different type of crushing processes. In addition, sand was chosen for ballast material due to its uniform grain size distribution and rounded grain shape. The maximum grain size of the ballast materials was between 5-10 mm. When comparing the compactibility of ballast materials, the highest dry densities were gained for ballast materials with graded grain size distribution. The compaction behaviour of the tested bentonite ballast mixtures is dominated by the bentonite content. The other parameters varied did not have significant effect on the compactibility of the mixtures with bentonite content of 30%. This can be explained with the amount of bentonite that is higher than what is needed to fill up the volume between the ballast grains. The results gained with the two different compaction tests are comparable. Both the bentonite/ballast mixtures and the Friedland clay behaved similarly when compacted with three different compaction pressures (180, 540 and 980 kPa). (orig.)

Behaviorally Green

DEFF Research Database (Denmark)

Sunstein, Cass; Reisch, Lucia A.

2016-01-01

of suggestion, inertia, and loss aversion. If well-chosen, green defaults are likely to have large effects in reducing the economic and environmental harms associated with various products and activities. Such defaults may or may not be more expensive to consumers. In deciding whether to establish green...