Sample records for raw edr electron
-
The response of Kodak EDR2 film in high-energy electron beams.
Gerbi, Bruce J; Dimitroyannis, Dimitri A
2003-10-01
Kodak XV2 film has been a key dosimeter in radiation therapy for many years. The advantages of the recently introduced Kodak EDR2 film for photon beam dosimetry have been the focus of several IMRT verification dosimetry publications. However, no description of this film's response to electron beams exists in the literature. We initiated a study to characterize the response and utility of this film for electron beam dosimetry. We exposed a series of EDR2 films to 6, 9, 12, 16, and 20 MeV electrons in addition to 6 and 18 MV x rays to develop standard characteristic curves. The linac was first calibrated to ensure that the delivered dose was known accurately. All irradiations were done at dmax in polystyrene for both photons and electrons, all films were from the same batch, and were developed at the same time. We also exposed the EDR2 films in a solid water phantom to produce central axis depth dose curves. These data were compared against percent depth dose curves measured in a water phantom using an IC-10 ion chamber, Kodak XV2 film, and a PTW electron diode. The response of this film was the same for both 6 and 18 MV x rays, but showed an apparent energy-dependent enhancement for electron beams. The response of the film also increased with increasing electron energy. This caused the percent depth dose curves using film to be shifted toward the surface compared to the ion chamber data.
-
Migliore, R.; Duncan, J.; Pulcino, V.; Bourne, D.; Voegt, S.; Perez, G.
2017-09-01
EDRS-C will operate on a geostationary orbit as the second node of the European Data Relay System (EDRS). The EDRS-C satellite, designed by OHB System as prime contractor, has been procured in the frame of a Public Private Partnership (PPP) between Airbus Defence and Space and ESA. EDRS-C is currently under assembly at OHB facilities in Bremen.
-
Hosting the first EDRS payload
Poncet, D.; Glynn, S.; Heine, F.
2017-11-01
The European Data Relay System (EDRS) will provide optical and microwave data relay services between Low Earth Orbit (LEO) satellites at altitudes up to 2000 km and the ground through geostationary (GEO) satellite nodes. Currently, two such nodes have been procured as part of a Public Private Partnership (PPP) between Astrium (now Airbus Defence and Space) and ESA. The first node (EDRS-A) is a hosted payload embarked upon the Eutelsat 9B satellite and scheduled for launch in early 2015.
-
Dosimetric accuracy of Kodak EDR2 film for IMRT verifications.
Childress, Nathan L; Salehpour, Mohammad; Dong, Lei; Bloch, Charles; White, R Allen; Rosen, Isaac I
2005-02-01
Patient-specific intensity-modulated radiotherapy (IMRT) verifications require an accurate two-dimensional dosimeter that is not labor-intensive. We assessed the precision and reproducibility of film calibrations over time, measured the elemental composition of the film, measured the intermittency effect, and measured the dosimetric accuracy and reproducibility of calibrated Kodak EDR2 film for single-beam verifications in a solid water phantom and for full-plan verifications in a Rexolite phantom. Repeated measurements of the film sensitometric curve in a single experiment yielded overall uncertainties in dose of 2.1% local and 0.8% relative to 300 cGy. 547 film calibrations over an 18-month period, exposed to a range of doses from 0 to a maximum of 240 MU or 360 MU and using 6 MV or 18 MV energies, had optical density (OD) standard deviations that were 7%-15% of their average values. This indicates that daily film calibrations are essential when EDR2 film is used to obtain absolute dose results. An elemental analysis of EDR2 film revealed that it contains 60% as much silver and 20% as much bromine as Kodak XV2 film. EDR2 film also has an unusual 1.69:1 silver:halide molar ratio, compared with the XV2 film's 1.02:1 ratio, which may affect its chemical reactions. To test EDR2's intermittency effect, the OD generated by a single 300 MU exposure was compared to the ODs generated by exposing the film 1 MU, 2 MU, and 4 MU at a time to a total of 300 MU. An ion chamber recorded the relative dose of all intermittency measurements to account for machine output variations. Using small MU bursts to expose the film resulted in delivery times of 4 to 14 minutes and lowered the film's OD by approximately 2% for both 6 and 18 MV beams. This effect may result in EDR2 film underestimating absolute doses for patient verifications that require long delivery times. After using a calibration to convert EDR2 film's OD to dose values, film measurements agreed within 2% relative
-
NPOESS Environmental Data Record (EDR) Production
Hughes, R.; Grant, K. D.
2009-12-01
The National Oceanic and Atmospheric Administration (NOAA), Department of Defense (DoD), and National Aeronautics and Space Administration (NASA) are jointly acquiring the next-generation weather and environmental satellite system; the National Polar-orbiting Operational Environmental Satellite System (NPOESS). NPOESS replaces the current Polar-orbiting Operational Environmental Satellites (POES) managed by NOAA and the Defense Meteorological Satellite Program (DMSP) managed by the DoD. The NPOESS satellites carry a suite of sensors that collect meteorological, oceanographic, climatological, and solar-geophysical observations of the earth, atmosphere, and space. The ground data processing segment for NPOESS is the Interface Data Processing Segment (IDPS), developed by Raytheon Intelligence and Information Systems. The IDPS processes NPOESS satellite data to provide environmental data products (aka, Environmental Data Records or EDRs) to NOAA and DoD processing centers operated by the United States government. The IDPS will process EDRs beginning with the NPOESS Preparatory Project (NPP) and continuing through the lifetime of the NPOESS system. Northrop Grumman Aerospace Systems Algorithms and Data Products (A&DP) organization is responsible for the algorithms that produce the EDRs, including their quality aspects. Together, IDPS and A&DP must support the calibration, validation, and data quality improvement initiatives of the NPOESS program to ensure the production of atmospheric and environmental products that meet strict requirements for accuracy and precision. In support of this activity, A&DP and IDPS continually updates the estimated performance of the NPOESS system with respect to both latency and data quality, using the latest operational implementation of the data processing software and information from instrument test activities. This presentation will illustrate and describe the processing chains that create the data products, as well as describe the
-
Zhang, Yunwei; Bai, Yang; Wu, Guangheng; Zou, Shenghao; Chen, Yongfang; Gao, Caixia; Tang, Dingzhong
2017-08-01
Wheat (Triticum aestivum L.) incurs significant yield losses from powdery mildew, a major fungal disease caused by Blumeria graminis f. sp. tritici (Bgt). enhanced disease resistance1 (EDR1) plays a negative role in the defense response against powdery mildew in Arabidopsis thaliana; however, the edr1 mutant does not show constitutively activated defense responses. This makes EDR1 an ideal target for approaches using new genome-editing tools to improve resistance to powdery mildew. We cloned TaEDR1 from hexaploid wheat and found high similarity among the three homoeologs of EDR1. Knock-down of TaEDR1 by virus-induced gene silencing or RNA interference enhanced resistance to powdery mildew, indicating that TaEDR1 negatively regulates powdery mildew resistance in wheat. We used CRISPR/Cas9 technology to generate Taedr1 wheat plants by simultaneous modification of the three homoeologs of wheat EDR1. No off-target mutations were detected in the Taedr1 mutant plants. The Taedr1 plants were resistant to powdery mildew and did not show mildew-induced cell death. Our study represents the successful generation of a potentially valuable trait using genome-editing technology in wheat and provides germplasm for disease resistance breeding. © 2017 The Authors The Plant Journal © 2017 John Wiley & Sons Ltd.
-
Electron Energization and Structure of the Diffusion Region During Asymmetric Reconnection
Chen, Li-Jen; Hesse, Michael; Wang, Shan; Bessho, Naoki; Daughton, William
2016-01-01
Results from particle-in-cell simulations of reconnection with asymmetric upstream conditions are reported to elucidate electron energization and structure of the electron diffusion region (EDR). Acceleration of unmagnetized electrons results in discrete structures in the distribution functions and supports the intense current and perpendicular heating in the EDR. The accelerated electrons are cyclotron turned by the reconnected magnetic field to produce the outflow jets, and as such, the acceleration by the reconnection electric field is limited, leading to resistivity without particle-particle or particle-wave collisions. A map of electron distributions is constructed, and its spatial evolution is compared with quantities previously proposed to be EDR identifiers to enable effective identifications of the EDR in terrestrial magnetopause reconnection.
-
Directory of Open Access Journals (Sweden)
Nishimura Marc
2007-07-01
Full Text Available Abstract Background The hypersensitive necrosis response (HR of resistant plants to avirulent pathogens is a form of programmed cell death in which the plant sacrifices a few cells under attack, restricting pathogen growth into adjacent healthy tissues. In spite of the importance of this defense response, relatively little is known about the plant components that execute the cell death program or about its regulation in response to pathogen attack. Results We isolated the edr2-6 mutant, an allele of the previously described edr2 mutants. We found that edr2-6 exhibited an exaggerated chlorosis and necrosis response to attack by three pathogens, two powdery mildew and one downy mildew species, but not in response to abiotic stresses or attack by the bacterial leaf speck pathogen. The chlorosis and necrosis did not spread beyond inoculated sites suggesting that EDR2 limits the initiation of cell death rather than its spread. The pathogen-induced chlorosis and necrosis of edr2-6 was correlated with a stimulation of the salicylic acid defense pathway and was suppressed in mutants deficient in salicylic acid signaling. EDR2 encodes a novel protein with a pleckstrin homology and a StAR transfer (START domain as well as a plant-specific domain of unknown function, DUF1336. The pleckstrin homology domain binds to phosphatidylinositol-4-phosphate in vitro and an EDR2:HA:GFP protein localizes to endoplasmic reticulum, plasma membrane and endosomes. Conclusion EDR2 acts as a negative regulator of cell death, specifically the cell death elicited by pathogen attack and mediated by the salicylic acid defense pathway. Phosphatidylinositol-4-phosphate may have a role in limiting cell death via its effect on EDR2. This role in cell death may be indirect, by helping to target EDR2 to the appropriate membrane, or it may play a more direct role.
-
Investigation of Kodak extended dose range (EDR) film for megavoltage photon beam dosimetry
International Nuclear Information System (INIS)
Chetty, Indrin J.; Charland, Paule M.
2002-01-01
We have investigated the dependence of the measured optical density on the incident beam energy, field size and depth for a new type of film, Kodak extended dose range (Kodak EDR). Film measurements have been conducted over a range of field sizes (3x3 cm 2 to 25x25 cm 2 ) and depths (d max to 15 cm), for 6 MV and 15 MV photons within a solid water phantom, and the variation in sensitometric response (net optical density versus dose) has been reported. Kodak EDR film is found to have a linear response with dose, from 0 to 350 cGy, which is much higher than that typically seen for Kodak XV film (0-50 cGy). The variation in sensitometric response for Kodak EDR film as a function of field size and depth is observed to be similar to that of Kodak XV film; the optical density varied in the order of 2-3% for field sizes of 3x3 cm 2 and 10x10 cm 2 at depths of d max , 5 cm and 15 cm in the phantom. Measurements for a 25x25 cm 2 field size showed consistently higher optical densities at depths of d max , 5 cm and 15 cm, relative to a 10x10 cm 2 field size at 5 cm depth, with 4-5% differences noted at a depth of 15 cm. Fractional depth dose and profiles conducted with Kodak EDR film showed good agreement (2%/2 mm) with ion chamber measurements for all field sizes except for the 25x25 cm 2 at depths greater than 15 cm, where differences in the order of 3-5% were observed. In addition, Kodak EDR film measurements were found to be consistent with those of Kodak XV film for all fractional depth doses and profiles. The results of this study indicate that Kodak EDR film may be a useful tool for relative dosimetry at higher dose ranges. (author)
-
Investigation of Kodak extended dose range (EDR) film for megavoltage photon beam dosimetry.
Chetty, Indrin J; Charland, Paule M
2002-10-21
We have investigated the dependence of the measured optical density on the incident beam energy, field size and depth for a new type of film, Kodak extended dose range (Kodak EDR). Film measurements have been conducted over a range of field sizes (3 x 3 cm2 to 25 x 25 cm2) and depths (d(max) to 15 cm), for 6 MV and 15 MV photons within a solid water phantom, and the variation in sensitometric response (net optical density versus dose) has been reported. Kodak EDR film is found to have a linear response with dose, from 0 to 350 cGy, which is much higher than that typically seen for Kodak XV film (0-50 cGy). The variation in sensitometric response for Kodak EDR film as a function of field size and depth is observed to be similar to that of Kodak XV film; the optical density varied in the order of 2-3% for field sizes of 3 x 3 cm2 and 10 x 10 cm2 at depths of d(max), 5 cm and 15 cm in the phantom. Measurements for a 25 x 25 cm2 field size showed consistently higher optical densities at depths of d(max), 5 cm and 15 cm, relative to a 10 x 10 cm2 field size at 5 cm depth, with 4-5% differences noted at a depth of 15 cm. Fractional depth dose and profiles conducted with Kodak EDR film showed good agreement (2%/2 mm) with ion chamber measurements for all field sizes except for the 25 x 25 cm2 at depths greater than 15 cm, where differences in the order of 3-5% were observed. In addition, Kodak EDR film measurements were found to be consistent with those of Kodak XV film for all fractional depth doses and profiles. The results of this study indicate that Kodak EDR film may be a useful tool for relative dosimetry at higher dose ranges.
-
Effect of processing time delay on the dose response of Kodak EDR2 film.
Childress, Nathan L; Rosen, Isaac I
2004-08-01
Kodak EDR2 film is a widely used two-dimensional dosimeter for intensity modulated radiotherapy (IMRT) measurements. Our clinical use of EDR2 film for IMRT verifications revealed variations and uncertainties in dose response that were larger than expected, given that we perform film calibrations for every experimental measurement. We found that the length of time between film exposure and processing can affect the absolute dose response of EDR2 film by as much as 4%-6%. EDR2 films were exposed to 300 cGy using 6 and 18 MV 10 x 10 cm2 fields and then processed after time delays ranging from 2 min to 24 h. An ion chamber measured the relative dose for these film exposures. The ratio of optical density (OD) to dose stabilized after 3 h. Compared to its stable value, the film response was 4%-6% lower at 2 min and 1% lower at 1 h. The results of the 4 min and 1 h processing time delays were verified with a total of four different EDR2 film batches. The OD/dose response for XV2 films was consistent for time periods of 4 min and 1 h between exposure and processing. To investigate possible interactions of the processing time delay effect with dose, single EDR2 films were irradiated to eight different dose levels between 45 and 330 cGy using smaller 3 x 3 cm2 areas. These films were processed after time delays of 1, 3, and 6 h, using 6 and 18 MV photon qualities. The results at all dose levels were consistent, indicating that there is no change in the processing time delay effect for different doses. The difference in the time delay effect between the 6 and 18 MV measurements was negligible for all experiments. To rule out bias in selecting film regions for OD measurement, we compared the use of a specialized algorithm that systematically determines regions of interest inside the 10 x 10 cm2 exposure areas to manually selected regions of interest. There was a maximum difference of only 0.07% between the manually and automatically selected regions, indicating that the use of
-
Zhu, X R; Jursinic, P A; Grimm, D F; Lopez, F; Rownd, J J; Gillin, M T
2002-08-01
A new type of radiographic film, Kodak EDR2 film, was evaluated for dose verification of intensity modulated radiation therapy (IMRT) delivered by a static multileaf collimator (SMLC). A sensitometric curve of EDR2 film irradiated by a 6 MV x-ray beam was compared with that of Kodak X-OMAT V (XV) film. The effects of field size, depth and dose rate on the sensitometric curve were also studied. It is found that EDR2 film is much less sensitive than XV film. In high-energy x-ray beams, the double hit process is the dominant mechanism that renders the grains on EDR2 films developable. As a result, in the dose range that is commonly used for film dosimetry for IMRT and conventional external beam therapy, the sensitometric curves of EDR2 films cannot be approximated as a linear function, OD = c * D. Within experimental uncertainty, the film sensitivity does not depend on the dose rate (50 vs 300 MU/min) or dose per pulse (from 1.0 x 10(-4) to 4.21 x 10(-4) Gy/pulse). Field sizes and depths (up to field size of 10 x 10 cm2 and depth = 10 cm) have little effect on the sensitometric curves. Percent depth doses (PDDs) for both 6 and 23 MV x rays were measured with both EDR2 and XV films and compared with ion chamber data. Film data are within 2.5% of the ion chamber results. Dose profiles measured with EDR2 film are consistent with those measured with an ion chamber. Examples of measured IMRT isodose distributions versus calculated isodoses are presented. We have used EDR2 films for verification of all IMRT patients treated by SMLC in our clinic. In most cases, with EDR2 film, actual clinical daily fraction doses can be used for verification of composite isodose distributions of SMLC-based IMRT.
-
Kodak EDR2 film for patient skin dose assessment in cardiac catheterization procedures.
Morrell, R E; Rogers, A T
2006-07-01
Patient skin doses were measured using Kodak EDR2 film for 20 coronary angiography (CA) and 32 percutaneous transluminal coronary angioplasty (PTCA) procedures. For CA, all skin doses were well below 1 Gy. However, 23% of PTCA patients received skin doses of 1 Gy or more. Dose-area product (DAP) was also recorded and was found to be an inadequate indicator of maximum skin dose. Practical compliance with ICRP recommendations requires a robust method for skin dosimetry that is more accurate than DAP and is applicable over a wider dose range than EDR2 film.
-
NUCAPS: NOAA Unique Combined Atmospheric Processing System Environmental Data Record (EDR) Products
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset consists of numerous retrieved estimates of hydrological variables and trace gases as Environmental Data Record (EDR) products from the NOAA Unique...
-
Chen, Li-Jen; Hesse, Michael; Wang, Shan; Gershman, Daniel; Ergun, Robert; Pollock, Craig; Torbert, Roy; Bessho, Naoki; Daughton, William; Dorelli, John;
2016-01-01
Measurements from the Magnetospheric Multiscale (MMS) mission are reported to show distinct features of electron energization and mixing in the diffusion region of the terrestrial magnetopause reconnection. At the ion jet and magnetic field reversals, distribution functions exhibiting signatures of accelerated meandering electrons are observed at an electron out-of-plane flow peak. The meandering signatures manifested as triangular and crescent structures are established features of the electron diffusion region (EDR). Effects of meandering electrons on the electric field normal to the reconnection layer are detected. Parallel acceleration and mixing of the inflowing electrons with exhaust electrons shape the exhaust flow pattern. In the EDR vicinity, the measured distribution functions indicate that locally, the electron energization and mixing physics is captured by two-dimensional reconnection, yet to account for the simultaneous four-point measurements, translational invariant in the third dimension must be violated on the ion-skin-depth scale.
-
Dogan, Nesrin; Leybovich, Leonid B; Sethi, Anil
2002-11-21
Film dosimetry provides a convenient tool to determine dose distributions, especially for verification of IMRT plans. However, the film response to radiation shows a significant dependence on depth, energy and field size that compromise the accuracy of measurements. Kodak's XV2 film has a low saturation dose (approximately 100 cGy) and, consequently, a relatively short region of linear dose-response. The recently introduced Kodak extended range EDR2 film was reported to have a linear dose-response region extending to 500 cGy. This increased dose range may be particularly useful in the verification of IMRT plans. In this work, the dependence of Kodak EDR2 film's response on the depth, field size and energy was evaluated and compared with Kodak XV2 film. Co-60, 6 MV, 10 MV and 18 MV beams were used. Field sizes were 2 x 2, 6 x 6, 10 x 10, 14 x 14, 18 x 18 and 24 x 24 cm2. Doses for XV2 and EDR2 films were 80 cGy and 300 cGy, respectively. Optical density was converted to dose using depth-corrected sensitometric (Hurter and Driffield, or H&D) curves. For each field size, XV2 and EDR2 depth-dose curves were compared with ion chamber depth-dose curves. Both films demonstrated similar (within 1%) field size dependence. The deviation from the ion chamber for both films was small forthe fields ranging from 2 x 2 to 10 x 10 cm2: < or =2% for 6, 10 and 18 MV beams. No deviation was observed for the Co-60 beam. As the field size increased to 24 x 24 cm2, the deviation became significant for both films: approximately 7.5% for Co-60, approximately 5% for 6 MV and 10 MV, and approximately 6% for 18 MV. During the verification of IMRT plans, EDR2 film showed a better agreement with the calculated dose distributions than the XV2 film.
-
Decontamination of drug vegetative raw material by relativistic electron beam
International Nuclear Information System (INIS)
Gorbanyuk, A.G.; Dikiy, I.L.; Yegorov, A.M.; Linnik, A.F.; Uskov, V.V.
2004-01-01
The new technology of decontamination of drug vegetative raw material and medical products is proposed. Advantages of use of relativistic beams in a range of electron energies from 0.5 MeV to 5 MeV for these purposes are shown in comparison with X-radiation of energy from 80 keV to 1 MeV
-
Potential of Electronic Plastic Waste as a Source of Raw Material and Energy Recovery
International Nuclear Information System (INIS)
Norazli Othman; Nor Ezlin Ahmad Basri; Lariyah Mohd Sidek
2009-01-01
Nowadays, the production of electronic equipment is one of the fastest growing industrial activities in this world. The increase use of plastic in this sector resulted in an increase of electronic plastic waste. Basically, electronic plastic material contains various chemical elements which act as a flame retardant when electronic equipment is operated. In general, the concept of recycling electronic plastic waste should be considered in order to protect the environment. For this purpose, research has been conducted to different resins of electronic plastic waste to identify the potential of electronic plastic waste as a source of raw material and energy recovery. This study was divided into two part for example determination of physical and chemical characteristics of plastic resins and calculation of heating value for plastic resins based on Dulong formula. Results of this research show that the average calorific value of electronic waste is 30,872.42 kJ/ kg (7,375 kcal/ kg). The emission factor analysis showed that the concentration of emission value that might occur during waste management activities is below the standard set by the Environment Quality Act 1974. Basically, this research shows that electronic plastic waste has the potential to become the source of raw material and energy recovery. (author)
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of suspended matter from the Visible Infrared Imaging Radiometer Suite (VIIRS)...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of snow cover from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument...
-
CLEM1-LUN/EAR/SKY-ASTAR/BSTAR/UVVIS/HRES/LWIR/NIR-2-EDR-V1.0
National Aeronautics and Space Administration — The Clementine EDR (Engineering Data Record) Image Archive contains 88 CD-ROM volumes with more than 1.9 million images. Each volume contains approximately 3 lunar...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational environmental data record (EDR) that contains pinpoint locations of active fires (AF) as identified by an algorithm...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains a high quality Environmental Data Record (EDR) of cloud masks from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument onboard...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) that contains pinpoint locations of active fires (AF) as identified by an algorithm...
-
Bessho, N.; Chen, L. J.; Hesse, M.; Wang, S.
2017-12-01
In asymmetric reconnection with a guide field in the Earth's magnetopause, electron motion in the electron diffusion region (EDR) is largely affected by the guide field, the Hall electric field, and the reconnection electric field. The electron motion in the EDR is neither simple gyration around the guide field nor simple meandering motion across the current sheet. The combined meandering motion and gyration has essential effects on particle acceleration by the in-plane Hall electric field (existing only in the magnetospheric side) and the out-of-plane reconnection electric field. We analyze electron motion and crescent-shaped electron distribution functions in the EDR in asymmetric guide field reconnection, and perform 2-D particle-in-cell (PIC) simulations to elucidate the effect of reconnection electric field on electron distribution functions. Recently, we have analytically expressed the acceleration effect due to the reconnection electric field on electron crescent distribution functions in asymmetric reconnection without a guide field (Bessho et al., Phys. Plasmas, 24, 072903, 2017). We extend the theory to asymmetric guide field reconnection, and predict the crescent bulge in distribution functions. Assuming 1D approximation of field variations in the EDR, we derive the time period of oscillatory electron motion (meandering + gyration) in the EDR. The time period is expressed as a hybrid of the meandering period and the gyro period. Due to the guide field, electrons not only oscillate along crescent-shaped trajectories in the velocity plane perpendicular to the antiparallel magnetic fields, but also move along parabolic trajectories in the velocity plane coplanar with magnetic field. The trajectory in the velocity space gradually shifts to the acceleration direction by the reconnection electric field as multiple bounces continue. Due to the guide field, electron distributions for meandering particles are bounded by two paraboloids (or hyperboloids) in the
-
An ontology-based method for secondary use of electronic dental record data
Schleyer, Titus KL; Ruttenberg, Alan; Duncan, William; Haendel, Melissa; Torniai, Carlo; Acharya, Amit; Song, Mei; Thyvalikakath, Thankam P.; Liu, Kaihong; Hernandez, Pedro
A key question for healthcare is how to operationalize the vision of the Learning Healthcare System, in which electronic health record data become a continuous information source for quality assurance and research. This project presents an initial, ontology-based, method for secondary use of electronic dental record (EDR) data. We defined a set of dental clinical research questions; constructed the Oral Health and Disease Ontology (OHD); analyzed data from a commercial EDR database; and created a knowledge base, with the OHD used to represent clinical data about 4,500 patients from a single dental practice. Currently, the OHD includes 213 classes and reuses 1,658 classes from other ontologies. We have developed an initial set of SPARQL queries to allow extraction of data about patients, teeth, surfaces, restorations and findings. Further work will establish a complete, open and reproducible workflow for extracting and aggregating data from a variety of EDRs for research and quality assurance. PMID:24303273
-
An ontology-based method for secondary use of electronic dental record data.
Schleyer, Titus Kl; Ruttenberg, Alan; Duncan, William; Haendel, Melissa; Torniai, Carlo; Acharya, Amit; Song, Mei; Thyvalikakath, Thankam P; Liu, Kaihong; Hernandez, Pedro
2013-01-01
A key question for healthcare is how to operationalize the vision of the Learning Healthcare System, in which electronic health record data become a continuous information source for quality assurance and research. This project presents an initial, ontology-based, method for secondary use of electronic dental record (EDR) data. We defined a set of dental clinical research questions; constructed the Oral Health and Disease Ontology (OHD); analyzed data from a commercial EDR database; and created a knowledge base, with the OHD used to represent clinical data about 4,500 patients from a single dental practice. Currently, the OHD includes 213 classes and reuses 1,658 classes from other ontologies. We have developed an initial set of SPARQL queries to allow extraction of data about patients, teeth, surfaces, restorations and findings. Further work will establish a complete, open and reproducible workflow for extracting and aggregating data from a variety of EDRs for research and quality assurance.
-
Suriyapee, S; Pitaxtarnin, N; Oonsiri, S; Jumpangern, C; Israngkul Na Ayuthaya, I
2008-01-01
To investigate the optimal sensitometric curves of extended dose range (EDR2) radiographic film in terms of depth, field size, dose range and processing conditions for dynamic intensity modulated radiation therapy (IMRT) dosimetry verification with 6 MV X-ray beams. A Varian Clinac 23 EX linear accelerator with 6 MV X-ray beam was used to study the response of Kodak EDR2 film. Measurements were performed at depths of 5, 10 and 15 cm in MedTec virtual water phantom and with field sizes of 2x2, 3x3, 10x10 and 15x15 cm(2). Doses ranging from 20 to 450 cGy were used. The film was developed with the Kodak RP X-OMAT Model M6B automatic film processor. Film response was measured with the Vidar model VXR-16 scanner. Sensitometric curves were applied to the dose profiles measured with film at 5 cm in the virtual water phantom with field sizes of 2x2 and 10x10 cm(2) and compared with ion chamber data. Scanditronix/Wellhofer OmniPro(TM) IMRT software was used for the evaluation of the IMRT plan calculated by Eclipse treatment planning. Investigation of the reproducibility and accuracy of the film responses, which depend mainly on the film processor, was carried out by irradiating one film nine times with doses of 20 to 450 cGy. A maximum standard deviation of 4.9% was found which decreased to 1.9% for doses between 20 and 200 cGy. The sensitometric curves for various field sizes at fixed depth showed a maximum difference of 4.2% between 2x2 and 15x15 cm(2) at 5 cm depth with a dose of 450 cGy. The shallow depth tended to show a greater effect of field size responses than the deeper depths. The sensitometric curves for various depths at fixed field size showed slightly different film responses; the difference due to depth was within 1.8% for all field sizes studied. Both field size and depth effect were reduced when the doses were lower than 450 cGy. The difference was within 2.5% in the dose range from 20 to 300 cGy for all field sizes and depths studied. Dose profiles
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument onboard the...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument onboard the...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument onboard the...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument onboard the...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains an Environmental Data Record (EDR) of Sea Ice Characterization (SIC) from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Cloud Base Heights (CBH) from the Visible Infrared Imaging Radiometer Suite...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Land Surface Temperature (LST) from the Visible Infrared Imaging Radiometer Suite...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality Environmental Data Record (EDR) of Cloud Cover Layers (CCL) from the Visible Infrared Imaging Radiometer Suite (VIIRS)...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Cloud Optical Thickness (COT) from the Visible Infrared Imaging Radiometer Suite...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Ocean Color/Chlorophyll (OCC) from the Visible Infrared Imaging Radiometer Suite...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of cloud type and phase from the Visible Infrared Imaging Radiometer Suite (VIIRS)...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Ice Thickness and Age from the Visible Infrared Imaging Radiometer Suite (VIIRS)...
-
Chikamori, Yoji; Nasu, Seigo
2017-01-01
The electronic materials and electronics device industries remain important to Japan in spite of the general decline of the Japanese electronics industry. There is risk and uncertainty when developing functional materials in the electronics industry. However, studies examining the uncertainty and risk variables in the development of functional materials are scarce. This study examines incremental research and development (R&D) developed for raw functional materials for electronics. Our analys...
-
Directory of Open Access Journals (Sweden)
A. A. Alekhin
2013-05-01
Full Text Available The article deals with creation results of experimental prototype of optical-electronic complex, designed to assess ore dressability of mineral raw materials by optical sorting method.
-
The Schwarzschild effect of the dosimetry film Kodak EDR 2.
Djouguela, A; Kollhoff, R; Rubach, A; Harder, D; Poppe, B
2005-11-07
The magnitude of the Schwarzschild effect or failure of the reciprocity law has been experimentally investigated for the dosimetry film EDR 2 from Kodak. When the dose rate applied to achieve a given dose was reduced by a factor of 12, the net optical density was reduced by up to 5%. The clinical importance of this effect is negligible as long as the films are calibrated at a value of the dose rate approximately representative of the dose rates occurring in the target volume, but in target regions of strongly reduced dose rate the Schwarzschild effect should be allowed for by a correction of the net optical density.
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument onboard the...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of volcanic ash from the Visible Infrared Imaging Radiometer (VIIRS) instrument...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) from the Visible Infrared Imaging Radiometer Suite (VIIRS) instrument onboard the...
-
Sankar, A; Ayyangar, Komanduri M; Nehru, R Mothilal; Kurup, P G Gopalakrishna; Murali, V; Enke, Charles A; Velmurugan, J
2006-01-01
The quantitative dose validation of intensity-modulated radiation therapy (IMRT) plans require 2-dimensional (2D) high-resolution dosimetry systems with uniform response over its sensitive region. The present work deals with clinical use of commercially available self-developing Radio Chromic Film, Gafchromic EBT film, for IMRT dose verification. Dose response curves were generated for the films using a VXR-16 film scanner. The results obtained with EBT films were compared with the results of Kodak extended dose range 2 (EDR2) films. The EBT film had a linear response between the dose range of 0 to 600 cGy. The dose-related characteristics of the EBT film, such as post irradiation color growth with time, film uniformity, and effect of scanning orientation, were studied. There was up to 8.6% increase in the color density between 2 to 40 hours after irradiation. There was a considerable variation, up to 8.5%, in the film uniformity over its sensitive region. The quantitative differences between calculated and measured dose distributions were analyzed using DTA and Gamma index with the tolerance of 3% dose difference and 3-mm distance agreement. The EDR2 films showed consistent results with the calculated dose distributions, whereas the results obtained using EBT were inconsistent. The variation in the film uniformity limits the use of EBT film for conventional large-field IMRT verification. For IMRT of smaller field sizes (4.5 x 4.5 cm), the results obtained with EBT were comparable with results of EDR2 films.
-
International Nuclear Information System (INIS)
Sankar, A.; Ayyangar, Komanduri M.; Nehru, R. Mothilal; Gopalakrishna Kurup, P.G.; Murali, V.; Enke, Charles A.; Velmurugan, J.
2006-01-01
The quantitative dose validation of intensity-modulated radiation therapy (IMRT) plans require 2-dimensional (2D) high-resolution dosimetry systems with uniform response over its sensitive region. The present work deals with clinical use of commercially available self-developing Radio Chromic Film, Gafchromic EBT film, for IMRT dose verification. Dose response curves were generated for the films using a VXR-16 film scanner. The results obtained with EBT films were compared with the results of Kodak extended dose range 2 (EDR2) films. The EBT film had a linear response between the dose range of 0 to 600 cGy. The dose-related characteristics of the EBT film, such as post irradiation color growth with time, film uniformity, and effect of scanning orientation, were studied. There was up to 8.6% increase in the color density between 2 to 40 hours after irradiation. There was a considerable variation, up to 8.5%, in the film uniformity over its sensitive region. The quantitative differences between calculated and measured dose distributions were analyzed using DTA and Gamma index with the tolerance of 3% dose difference and 3-mm distance agreement. The EDR2 films showed consistent results with the calculated dose distributions, whereas the results obtained using EBT were inconsistent. The variation in the film uniformity limits the use of EBT film for conventional large-field IMRT verification. For IMRT of smaller field sizes (4.5 x 4.5 cm), the results obtained with EBT were comparable with results of EDR2 films
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Cloud Effective Particle Size (CEPS) from the Visible Infrared Imaging Radiometer...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains VIIRS Ocean Color Reprocessed Environmental Data Record (EDR) Level 3 products produced by the NESDIS Center for Satellite Applications and...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains VIIRS Ocean Color Reprocessed Environmental Data Record (EDR) Level 2 products produced by the NESDIS Center for Satellite Applications and...
-
Exploring Dental Providers' Workflow in an Electronic Dental Record Environment.
Schwei, Kelsey M; Cooper, Ryan; Mahnke, Andrea N; Ye, Zhan; Acharya, Amit
2016-01-01
A workflow is defined as a predefined set of work steps and partial ordering of these steps in any environment to achieve the expected outcome. Few studies have investigated the workflow of providers in a dental office. It is important to understand the interaction of dental providers with the existing technologies at point of care to assess breakdown in the workflow which could contribute to better technology designs. The study objective was to assess electronic dental record (EDR) workflows using time and motion methodology in order to identify breakdowns and opportunities for process improvement. A time and motion methodology was used to study the human-computer interaction and workflow of dental providers with an EDR in four dental centers at a large healthcare organization. A data collection tool was developed to capture the workflow of dental providers and staff while they interacted with an EDR during initial, planned, and emergency patient visits, and at the front desk. Qualitative and quantitative analysis was conducted on the observational data. Breakdowns in workflow were identified while posting charges, viewing radiographs, e-prescribing, and interacting with patient scheduler. EDR interaction time was significantly different between dentists and dental assistants (6:20 min vs. 10:57 min, p = 0.013) and between dentists and dental hygienists (6:20 min vs. 9:36 min, p = 0.003). On average, a dentist spent far less time than dental assistants and dental hygienists in data recording within the EDR.
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of cloud height (top and base) from the Visible Infrared Imaging Radiometer Suite...
-
Ward, Lindsay R; Kerth, Chris R; Pillai, Suresh D
2017-07-01
Raw milk is known to contain relatively high numbers of microorganisms, some of which include microbial pathogens. Electron beam (eBeam) processing is a nonthermal pasteurization food processing technology. The underlying hypothesis was that eBeam processing will not negatively influence the composition, nutrient content, and aroma profile of raw milk. Raw milk samples were exposed to eBeam doses of 1 and 2 kGy, since our studies had shown that 2 kGy is suitable for raw milk pasteurization. The untreated and eBeam-treated raw milk samples were analyzed to detect changes in lactose, vitamin B 2 , vitamin B 12 , and calcium concentrations. The possible breakdown of casein and whey proteins and lipid oxidation were investigated along with the formation of volatile aroma compounds. Even though vitamin B 2 showed a 31.6% decrease in concentration, the B 2 content in eBeam-pasteurized raw milk met all USDA nutritional guidelines. Even though there were no indications of lipid oxidation after the 2.0-kGy eBeam treatment, there was lipid oxidation (58%) after 7 d of refrigerated storage. However, based on the GC-olfactory analysis, the lipid oxidation did not necessarily result in the development of a wide variety of off-odors. © 2017 Institute of Food Technologists®.
-
Directory of Open Access Journals (Sweden)
Varatharaj C
2010-01-01
Full Text Available Background: The evaluation of the agreement between measured and calculated dose plays an essential role in the quality assurance (QA procedures of intensity-modulated radiation therapy (IMRT. Aim: The purpose of this study is to compare performances of the two dosimetric systems (EDR2 and I′matriXX in the verification of the dose distributions calculated by the TPS for brain and head and neck dynamic IMRT cases. Materials and Methods: The comparison of cumulative fluence by using Kodak extended dose rate (EDR2 and I′matriXX detectors has been done for the evaluation of 10 brain, 10 head and neck IMRT cases treated with 6 MV beams. The parameter used to assess the quality of dose calculation is the gamma-index (g -index method. The acceptance limits for g calculation we have used are 3% and 3 mm respectively for dose agreement and distance to agreement parameters. Statistical analyses were performed by using the paired, two-tailed Student t-test, and P< 0.01 is kept as a threshold for the significance level. Results: The qualitative dose distribution comparison was performed using composite dose distribution in the measurement plane and profiles along various axes for TPS vs. EDR2 film and TPS Vs I′matriXX. The quantitative analysis between the calculated and measured dose distribution was evaluated using DTA and g-index. The percentage of pixels matching with the set DTA and g values are comparable for both with EDR2 film and I′matriXX array detectors. Statistically there was no significant variation observed between EDR2 film and I′matriXX in terms of the mean percentage of pixel passing g for brain cases (98.77 ± 1.03 vs 97.62 ± 1.66, P = 0.0218 and for head and neck cases (97.39 ± 2.13 vs 97.17 ± 1.52%, P = 0.7404. Conclusion: Due to simplicity and fast evaluation process of array detectors, it can be routinely used in busy departments without compromising the measurement accuracy.
-
National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains a high quality Environmental Data Record (EDR) of nighttime cloud optical and microphysical properties (NCOMP) from the Visible Infrared...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Snow Cover/Depth Fraction (SCF) from the Visible Infrared Imaging Radiometer...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Binary Snow Cover (BSC) from the Visible Infrared Imaging Radiometer Suite...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Sea Ice Concentration (SIC) and Ice Surface Temperature (IST) from the Visible...
-
Exploring Dental Providers’ Workflow in an Electronic Dental Record Environment
Schwei, Kelsey M; Cooper, Ryan; Mahnke, Andrea N.; Ye, Zhan
2016-01-01
Summary Background A workflow is defined as a predefined set of work steps and partial ordering of these steps in any environment to achieve the expected outcome. Few studies have investigated the workflow of providers in a dental office. It is important to understand the interaction of dental providers with the existing technologies at point of care to assess breakdown in the workflow which could contribute to better technology designs. Objective The study objective was to assess electronic dental record (EDR) workflows using time and motion methodology in order to identify breakdowns and opportunities for process improvement. Methods A time and motion methodology was used to study the human-computer interaction and workflow of dental providers with an EDR in four dental centers at a large healthcare organization. A data collection tool was developed to capture the workflow of dental providers and staff while they interacted with an EDR during initial, planned, and emergency patient visits, and at the front desk. Qualitative and quantitative analysis was conducted on the observational data. Results Breakdowns in workflow were identified while posting charges, viewing radiographs, e-prescribing, and interacting with patient scheduler. EDR interaction time was significantly different between dentists and dental assistants (6:20 min vs. 10:57 min, p = 0.013) and between dentists and dental hygienists (6:20 min vs. 9:36 min, p = 0.003). Conclusions On average, a dentist spent far less time than dental assistants and dental hygienists in data recording within the EDR. PMID:27437058
-
NIMS EXPERIMENT DATA RECORDS: SL-9 COMET IMPACT WITH JUPITER
National Aeronautics and Space Administration — NIMS Experiment Data Record (EDR) files contain raw data from the Galileo Orbiter Near-Infrared Mapping Spectrometer (CARLSONETAL1992). This raw data requires...
-
NIMS EXPERIMENT DATA RECORDS: GASPRA/IDA ENCOUNTERS
National Aeronautics and Space Administration — NIMS Experiment Data Record (EDR) files contain raw data from the Galileo Orbiter Near-Infrared Mapping Spectrometer (CARLSONETAL1992). This raw data requires...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of total column ozone from the Ozone Mapping and Profiling Suite (OMPS) instrument...
-
Estimates of Terms in Ohm's Law During an Encounter with an Electron Diffusion Region
Torbert, R. B.; Burch, J. L.; Giles, B. L.; Gershman, D.; Pollock, C. J.; Dorelli, J.; Avanov, L. A.; Argall, M.; Shuster, J.; Strangeway, R.;
2016-01-01
We present measurements from the Magnetospheric Multiscale (MMS) mission taken during a reconnection event on the dayside magnetopause which includes a passage through an electron diffusion region (EDR). The four MMS satellites were separated by about 10 km such that estimates of gradients and divergences allow a reasonable estimate of terms in the generalized Ohm's law, which is key to investigating the energy dissipation during reconnection. The strength and character of dissipation mechanisms determines how magnetic energy is released. We show that both electron pressure gradients and electron inertial effects are important, but not the only participants in reconnection near EDRs, since there are residuals of a few mVm (approximately 30-50%) of E+ U(sub e) x B (from the sum of these two terms) during the encounters. These results are compared to a simulation, which exhibits many of the observed features, but where relatively little residual is present.
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of nadir profiler ozone from the Ozone Mapping and Profiling Suite (OMPS) instrument...
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of aerosol optical depth (AOD) and particle size from the Visible Infrared Imaging...
-
International Nuclear Information System (INIS)
Eggert, F.; Heckel, J.
1986-01-01
The method realized in program QMA-184 of the energy dispersive X-Ray-Microanalyzer EDR-184 for quantitative spectra analyzing of bulk materials by using local peak-to-background ratios is described in detail. The authors demonstrate efficiency and limitations of the used method by discussion of experimental results. (author)
-
Comparison of High Performance Network Options: EDR InfiniBand vs.100Gb RDMA Capable Ethernet
Energy Technology Data Exchange (ETDEWEB)
Kachelmeier, Luke Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Univ. of New Mexico, Albuquerque, NM (United States); Van Wig, Faith Virginia [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Missouri Univ. of Science and Technology, Rolla, MO (United States); Erickson, Kari Natania [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); New Mexico Inst. of Mining and Technology, Socorro, NM (United States)
2016-08-08
These are the slides for a presentation at the HPC Mini Showcase. This is a comparison of two different high performance network options: EDR InfiniBand and 100Gb RDMA capable ethernet. The conclusion of this comparison is the following: there is good potential, as shown with the direct results; 100Gb technology is too new and not standardized, thus deployment effort is complex for both options; different companies are not necessarily compatible; if you want 100Gb/s, you must get it all from one place.
-
Effect of electron beam-cross-linked gels on the rheological properties of raw natural rubber
Energy Technology Data Exchange (ETDEWEB)
Mitra, Suman; Chattopadhyay, Santanu [Rubber Technology Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Bharadwaj, Y.K.; Sabharwal, S. [Radiation Technology Development Section, Bhabha Atomic Research Center, Trombay, Mumbai 400085 (India); Bhowmick, Anil K. [Rubber Technology Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India)], E-mail: anilkb@rtc.iitkgp.ernet.in
2008-05-15
Electron beam (EB)-cross-linked natural rubber (NR) gels were prepared from latex and characterized by various techniques. The addition of a small amount of these gels to raw NR was found to reduce the apparent shear viscosity and die swell remarkably. This effect was further enhanced with the addition of butyl acrylate as a sensitizer. The apparent shear viscosity first decreased up to 8 phr of gel loading and then increased. However, the percent die swell value decreased steadily upon gel loading. These were explained by calculating principal normal stress difference, the activation energy of melt flow and characteristics of EB-cross-linked gels. These effects were also reflected in the changes of mechanical and dynamic mechanical properties of gel-filled raw NR. Tailoring of the above properties could be done with the help of these gels.
-
National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains a high quality operational Environmental Data Record (EDR) of Aerosol Optical Thickness (AOT) from the Visible Infrared Imaging Radiometer...
-
THE USE OF EVENT DATA RECORDER (EDR – BLACK BOX
Directory of Open Access Journals (Sweden)
Gabriel Nowacki
2014-03-01
Full Text Available The paper refers to the registration of road events by a modern device called EDR – black box for all types of the motor vehicles. The device records data concerning vehicle’s technical condition, the way it was driven and RTS. The recorder may be used in private and commercial cars, taxies, buses and trucks. The recorder may serve the purpose of a neutral witness for the police, courts and insurance firms, for which it will facilitate making the reconstruction of the road accidents events and will provide a proof for those who caused them. The device will bring efficient driving, which will significantly contribute to decreasing the number of road accidents and limiting the environmental pollution. In the end in the last year German parliament backed a proposal to the European Commission to put black boxes, which gather information from vehicles involved in accidents, in all the new cars from 2015 on.
-
Comparison of auxiliary feedwater and EDRS operation during natural circulation of MRX
International Nuclear Information System (INIS)
Kim, Jae Hak; Park, Goon Cherl
1997-01-01
The MRX is an integral type ship reactor with 100 MWt power, which is designed by Japan Atomic Energy Research Institute. It is characterized by integral type PWR, in-vessel type control rod drive mechanism, water-filled containment vessel and passive decay heat removal system. Marine reactor should have high passive safety. Therefore, in this study, we simulated the loss of flow accident to verify the passive decay heat removal by natural circulation using RETRAN-03 code. auxiliary feed water systems are used for decay heat removal mechanism and results are compared with the loss of flow accident analysis using emergency decay heat removal system by JAERI. Results are very similar to case of EDRS 1 loop operation in JAERI analysis and decay heat is successfully removed by natural circulation
-
2013-03-21
... Purchased. contracting custom processing must report. Raw pounds by crab fishery. Product and processes by... purchased (raw Purchased. pounds) by crab fishery. Custom processing services purchased (product and process... greatest information value to the management decision making process. The EDR is required to be submitted...
-
Electron heating in the exhaust of magnetic reconnection with negligible guide field
Wang, Shan; Chen, Li-Jen; Bessho, Naoki; Kistler, Lynn M.; Shuster, Jason R.; Guo, Ruilong
2016-03-01
Electron heating in the magnetic reconnection exhaust is investigated with particle-in-cell simulations, space observations, and theoretical analysis. Spatial variations of the electron temperature (Te) and associated velocity distribution functions (VDFs) are examined and understood in terms of particle energization and randomization processes that vary with exhaust locations. Inside the electron diffusion region (EDR), the electron temperature parallel to the magnetic field (Te∥) exhibits a local minimum and the perpendicular temperature (Te⊥) shows a maximum at the current sheet midplane. In the intermediate exhaust downstream from the EDR and far from the magnetic field pileup region, Te⊥/Te∥ is close to unity and Te is approximately uniform, but the VDFs are structured: close to the midplane, VDFs are quasi-isotropic, whereas farther away from the midplane, VDFs exhibit field-aligned beams directed toward the midplane. In the far exhaust, Te generally increases toward the midplane and the pileup region, and the corresponding VDFs show counter-streaming beams. A distinct population with low v∥ and high v⊥ is prominent in the VDFs around the midplane. Test particle results show that the magnetic curvature near the midplane produces pitch angle scattering to generate quasi-isotropic distributions in the intermediate exhaust. In the far exhaust, electrons with initial high v∥ (v⊥) are accelerated mainly through curvature (gradient-B) drift opposite to the electric field, without significant pitch angle scattering. The VDF structures predicted by simulations are observed in magnetotail reconnection measurements, indicating that the energization mechanisms captured in the reported simulations are applicable to magnetotail reconnection with negligible guide field.
-
MESSENGER E/V/H GRNS 2 GAMMA RAY SPECTROMETER RAW DATA V1.0
National Aeronautics and Space Administration — Abstract ======== This data set consists of the MESSENGER GRS uncalibrated observations, also known as EDRs. The GRS experiment is a gamma ray spectrometer designed...
-
Electronic dental records: start taking the steps.
Bergoff, Jana
2011-01-01
Converting paper patient records charts into their electronic counterparts (EDRs) not only has many advantages, but also could become a legal requirement in the future. Several steps key to a successful transition includes assessing the needs of the dental team and what they require as a part of the implementation Existing software and hardware must be evaluated for continued use and expansion. Proper protocols for information transfer must be established to ensure complete records while maintaining HIPAA regulations regarding patient privacy. Reduce anxiety by setting realistic dead-lines and using trusted back-up methods.
-
LRO MOON CRATER EDR RAWDATA VERSION 1.0
National Aeronautics and Space Administration — This data set comprises the raw binary data from from the LRO Cosmic Ray Telescope for the Effects of Radiation (CRaTER) instrument. The data consists of the...
-
Torbert, R. B.; Burch, J. L.; Argall, M. R.; Alm, L.; Farrugia, C. J.; Forbes, T. G.; Giles, B. L.; Rager, A.; Dorelli, J.; Strangeway, R. J.; Ergun, R. E.; Wilder, F. D.; Ahmadi, N.; Lindqvist, P.-A.; Khotyaintsev, Y.
2017-12-01
On 22 October 2016, the Magnetospheric Multiscale (MMS) spacecraft encountered the electron diffusion region (EDR) when the magnetosheath field was southward, and there were signatures of fast reconnection, including flow jets, Hall fields, and large power dissipation. One rapid, normal-incidence crossing, during which the EDR structure was almost stationary in the boundary frame, provided an opportunity to observe the spatial structure for the zero guide field case of magnetic reconnection. The reconnection electric field was determined unambiguously to be 2-3 mV/m. There were clear signals of fluctuating parallel electric fields, up to 6 mV/m on the magnetosphere side of the diffusion region, associated with a Hall-like parallel current feature on the electron scale. The width of the main EDR structure was determined to be 2 km (1.8 de). Although the MMS spacecraft were in their closest tetrahedral separation of 8 km, the divergences and curls for these thin current structures could therefore not be computed in the usual manner. A method is developed to determine these quantities on a much smaller scale and applied to compute the normal component of terms in the generalized Ohm's law for the positions of each individual spacecraft (not a barocentric average). Although the gradient pressure term has a qualitative dependence that follows the observed variation of E + Ve × B, the quantitative magnitude of these terms differs by more than a factor of 2, which is shown to be greater than the respective errors. Thus, future research is required to find the manner in which Ohm's law is balanced.
-
Recovery of the secondary raw materials, recycling
International Nuclear Information System (INIS)
Chmielewska, E.
2010-01-01
In this chapter the recovery and recycling of secondary raw materials is explained. This chapter consists of the following parts: Paper and tetrapaks; Car wrecks; Scrap metal; Plastics; Used tires; Electrical and electronic equipment; Glass; Accumulators and batteries; Spent oil; Low-and non-waste technology.
-
Remediation of raw sewage water by ionizing radiation
International Nuclear Information System (INIS)
El-Motaium, R.A.; Laroussi, B.F.
2007-01-01
Raw sewage water has been used for irrigation in many countries in the world including Egypt. Although the reuse of sewage water for irrigation has become essential, this practice could represent a hazard to the environment and human health. Radiation treatment was applied to test its effect on the remediation of raw sewage water collected from the inlet of El-Gabal El-Asfar Waste Water Treatment Plant, north east of Cairo city. Different doses of gamma radiation and electron beam ( 0.5, 1.0, 1.5, 2.0, 2.5 KGy) were tested for their effects on raw sewage water properties. The parameters tested were total Coliform, BOD, COD, TSS, ph, EC, heavy metals, NH 4 and NO 3 . The data showed an inverse relationship between radiation dose and total Coliform, BOD, COD and TSS. This result proved true for both kinds of radiations. However, the effect of gamma radiation was more pronounced than the electron beam at the same dose. The lethal doses for total Coliform were 1.5 KGy and 3.0 KGy for gamma radiation and electron beam, respectively. Regarding ammonium and nitrate ions, there was a reduction in their content as the radiation dose increased. The reduction was 20% for NH 4 and 21% for NO 3 at 2.5 KGy dose using gamma or electron beam, respectively. The total heavy metals levels were 40.0, 5.8, 55.9, 0.55, 32.2 and 16.4 ppb for Ni, Co, Cu, Cd, Pb and Zn. The soluble fraction were 19.5, 3.3, 8.3, 0.02, 0.50, 3.1 ppb representing 49%, 58%, 15%, 3%, 1.6% and 19% of the total Ni, Co, Cu, Cd, Pb and Zn, respectively. In general, there was a tendency for reduction of the soluble fractions of heavy metals as the radiation dose increased
-
Morrell, Rachel E; Rogers, Andy
2004-12-21
Kodak EDR2 film has been calibrated across the range of exposure conditions encountered in our cardiac catheterization laboratory. Its dose-response function has been successfully modelled, up to the saturation point of 1 Gy. The most important factor affecting film sensitivity is the use of beam filtration. Spectral filtration and kVp together account for a variation in dose per optical density of -10% to +25%, at 160 mGy. The use of a dynamic wedge filter may cause doses to be underestimated by up to 6%. The film is relatively insensitive to variations in batch, field size, exposure rate, time to processing and day-to-day fluctuations in processor performance. Overall uncertainty in the calibration is estimated to be -20% to +40%, at 160 mGy. However, the uncertainty increases at higher doses, as the curve saturates. Artefacts were seen on a number of films, due to faults in the light-proofing of the film packets.
-
Photoshop CS3 RAW Transforming your RAW data into works of art
Aaland, Mikkel
2008-01-01
Because RAW files remain virtually untouched by in-camera processing, working with them has given digital photographers greater flexibility and control during the editing process -- for those who are familiar enough with the format. Camera RAW, the plug in for Adobe Photoshop CS3, has emerged as one of the best and most familiar tools for editing RAW images, and the best way to master this workflow is with Photoshop CS3 RAW. Award-winning author Mikkel Aaland explores the entire RAW process, from the practical reasons to shoot RAW, to managing the images with the new features of Bridge 2.0 n
-
LRO LUNAR EXPLORATION NEUTRON DETECTOR 2 EDR V1.0
National Aeronautics and Space Administration — Raw, uncalibrated housekeeping and scientific data collected from the Lunar Exploration Neutron Detector (LEND) aboard the Lunar Reconnaissance Orbiter.
-
ISMRM Raw data format: A proposed standard for MRI raw datasets
DEFF Research Database (Denmark)
Inati, Souheil; Naegle, Joseph; R. Zwart, Nicholas
2016-01-01
programming languages (C++, MATLAB, Python). Results Images were obtained by reconstructing the raw data from all vendors. The source code, raw data, and images comprising this work are shared online, serving as an example of an image reconstruction project following a paradigm of reproducible research......Purpose This work proposes the ISMRM Raw Data format as a common MR raw data format, which promotes algorithm and data sharing. Methods A file format consisting of a flexible header and tagged frames of k-space data was designed. Application Programming Interfaces were implemented in C/C++, MATLAB......, and Python. Converters for Bruker, General Electric, Philips, and Siemens proprietary file formats were implemented in C++. Raw data were collected using magnetic resonance imaging scanners from four vendors, converted to ISMRM Raw Data format, and reconstructed using software implemented in three...
-
Andrews, Philip
2007-01-01
One of the most important technologies a photographer can master is shooting and working with raw images. However, figuring out the best way to work with raw files can be confusing and overwhelming. What's the advantage to working in raw? How do you manage, organize, and store raw files? What's the best way to process your files to meet your photographic needs? How do Photoshop, Lightroom and Adobe Camera Raw work together? Is it possible to keep your photos in the raw format and still enhance them extensively? Philip Andrews answers these questions and more in his all-new essential raw workfl
-
International Nuclear Information System (INIS)
Vikulin, A.A.; Vanyushkin, B.M.; Garnyk, D.V.; Kon'kov, N.G.; Terent'ev, B.M.
1980-01-01
Measurement results of exposure dose rate (EDR) of radiation in fields of bremsstrahlung of radiation plants with LUEh-8/5B linear accelerator of electrons by means of DRG2-03 dose meter, intended for operative measuring EDR in high intense fields of γ-radiation of powerful radioisotopic plants, are presented. Dose meter design is described. Measurements of bremsstrahlung EDR have been carried out in the chamber of plant irradiation for radiation sterilizing medical items, as well as in the chamber of VNIIRT experimental plant. RUP-1 device has been used for measuring radiation EDR in a labyrinth behind 1.8 m thick shoulder by concrete [ru
-
Radiation sterilization of some cosmetic raw materials and preparations
International Nuclear Information System (INIS)
Achmatowicz-Szmajke, T.; Bryl-Sandelewska, T.; Galazka, M.
1979-01-01
The problem of microbiological purity of cosmetic preparations is discussed. Some results obtained on the influence of ionizing radiation on organoleptic and physicochemical properties of some cosmetic raw materials and final products are reported. The samples of raw materials and the final products were irradiated with a 10 MeV electron beam from an LAE 13/9 linear accelerator located in INR. The doses delivered to the materials were 0.5 - 2.3 Mrad (5-23 kGy). Immediately after irradiation, organoleptic estimations were made and over the next few days physicochemical investigations were performed. Non-irradiated samples were investigated together with irradiated ones. (T.I.)
-
The Forensics Aspects of Event Data Recorders
Directory of Open Access Journals (Sweden)
Jeremy S. Daily
2008-09-01
Full Text Available The proper generation and preservation of digital data from Event Data Recorders (EDRs can provide invaluable evidence to automobile crash reconstruction investigations. However, data collected from the EDR can be difficult to use and authenticate, complicating the presentation of such information as evidence in legal proceedings. Indeed, current techniques for removing and preserving such data do not meet the court’s standards for electronic evidence. Experimentation with an EDR unit from a 2001 GMC Sierra pickup truck highlighted particular issues with repeatability of results. Fortunately, advances in the digital forensics field and memory technology can be applied to EDR analysis in order to provide more complete and usable data. The presented issues should assist in the identification and development of a model for forensically sound collection and investigation techniques for EDRs.
-
One step sintering of homogenized bauxite raw material and kinetic study
Gao, Chang-he; Jiang, Peng; Li, Yong; Sun, Jia-lin; Zhang, Jun-jie; Yang, Huan-ying
2016-10-01
A one-step sintering process of bauxite raw material from direct mining was completed, and the kinetics of this process was analyzed thoroughly. The results show that the sintering kinetics of bauxite raw material exhibits the liquid-phase sintering behavior. A small portion of impurities existed in the raw material act as a liquid phase. After X-ray diffraction analyses, scanning electron microscopy observations, and kinetics calculations, sintering temperature and heating duration were determined as the two major factors contributing to the sintering process and densification of bauxite ore. An elevated heating temperature and longer duration favor the densification process. The major obstacle for the densification of bauxite material is attributed to the formation of the enclosed blowhole during liquid-phase sintering.
-
Parsing and Quantification of Raw Orbitrap Mass Spectrometer Data Using RawQuant.
Kovalchik, Kevin A; Moggridge, Sophie; Chen, David D Y; Morin, Gregg B; Hughes, Christopher S
2018-06-01
Effective analysis of protein samples by mass spectrometry (MS) requires careful selection and optimization of a range of experimental parameters. As the output from the primary detection device, the "raw" MS data file can be used to gauge the success of a given sample analysis. However, the closed-source nature of the standard raw MS file can complicate effective parsing of the data contained within. To ease and increase the range of analyses possible, the RawQuant tool was developed to enable parsing of raw MS files derived from Thermo Orbitrap instruments to yield meta and scan data in an openly readable text format. RawQuant can be commanded to export user-friendly files containing MS 1 , MS 2 , and MS 3 metadata as well as matrices of quantification values based on isobaric tagging approaches. In this study, the utility of RawQuant is demonstrated in several scenarios: (1) reanalysis of shotgun proteomics data for the identification of the human proteome, (2) reanalysis of experiments utilizing isobaric tagging for whole-proteome quantification, and (3) analysis of a novel bacterial proteome and synthetic peptide mixture for assessing quantification accuracy when using isobaric tags. Together, these analyses successfully demonstrate RawQuant for the efficient parsing and quantification of data from raw Thermo Orbitrap MS files acquired in a range of common proteomics experiments. In addition, the individual analyses using RawQuant highlights parametric considerations in the different experimental sets and suggests targetable areas to improve depth of coverage in identification-focused studies and quantification accuracy when using isobaric tags.
-
Strategic raw materials. Risk management
International Nuclear Information System (INIS)
Bertau, Martin; Matschullat, Joerg; Kausch, Peter
2014-01-01
This volume is divided into four chapters: (1) Raw material management, (2) Primary raw materials, (3) Secondary raw materials and recycling, (4). Processing and products. The topics for the chapter ''Raw material management'' are: Substitution of raw materials - framework conditions and implementation; Thales: Strategic raw materials; Time for cooperation between the EU and China in raw materials policy; Availability of elements for the semiconductor industry; Market price risks of raw material-intensive companies - identification and management. The topics on the second item ''Primary raw materials'' are: The supply of economic-critical raw materials - A search and analysis for causes; Lithium extraction from primary raw materials - state and perspectives; The global market of rare earths - A balancing act; Rare earth deposits in Namibia; New technologies in exploration and discovery - Focus on activities in Europe. The third chapter, ''Secondary Raw Materials and Recycling'', covered the topics: Technology metals - Systemic Requirements along the recycling chain; Integrated re-use of high-tech and greentech wastes; From the sewage sludge ash to the phosphorus fertilizer RecoPhos P38 in the stress field of waste, fertilizer and soil protection. In chapter 4. ''Processing and products'' are the topics: Treatment and processing of rare earth metals; Processing of mineral resources - opportunities and challenges; Consequences of modern germanium chemistry; Strategic resources - Risk management. A review and outlook with a pinch of fantasy.. [de
-
... and Food Safety Food Safety Modernization Act Raw Milk Recommend on Facebook Tweet Share Compartir RAW MILK ... Decide? Questions & Answers Outbreak Studies Resources & Publications Raw Milk Infographic [PDF – 1 page] More Resources 5 Raw ...
-
Prevalence of Arcobacter spp. in raw milk and retail raw meats in northern Ireland
DEFF Research Database (Denmark)
Scullion, R.; Harrington, C.S.; Madden, R.H.
2006-01-01
A 1-year study was undertaken to determine the prevalence of Arcobacter spp. in raw milk and retail raw meats on sale in Northern Ireland. Retail raw poultry samples (n = 94), pork samples (n = 101), and beef samples (n = 108) were obtained from supermarkets in Northern Ireland, and raw milk samp...... from raw milk samples. Arcobacter cryaerophilus was detected less frequently, and Arcobacter skirrowii was detected only as a cocontaminant. To our knowledge, this is the first report of Arcobacter spp. prevalence in a diverse range of products of animal origin in Northern Ireland....
-
Raw material versus processing
International Nuclear Information System (INIS)
Berg, E.A.T.
1989-01-01
Some brazilian aspects related with the obtainment of raw materials for advanced ceramic products are described. The necessity of import raw materials by the advanced ceramic industries is mentioned, generating dangerous depedence for the country. The brazilian mineral reserves for using in raw materials of advanced ceramic are also cited. (C.G.C.) [pt
-
SU-G-TeP1-13: Reclined Total Skin Electron Treatment Technique
Energy Technology Data Exchange (ETDEWEB)
Mathew, D; Gerbi, B [University of Minnesota, Minneapolis, MN (United States)
2016-06-15
Purpose: The purpose is to describe a new reclined technique for treatment of weakened patients that require total skin electron irradiation. Methods: This technique is a modification of a previously published reclined technique differing in that all six patient positions are treated with the gantry angled 60° from vertically down. The patient is located at a treatment distance of 330 cm SSD along the CA of the beam. The 3/8′ thick Lexan beam spoiler is placed 25 cm from the most proximal surface of the patient for all patient treatment positions. To produce a flat, uniform field of ∼190 cm length, the patient was moved longitudinally by an experimentally determined distance. Kodak EDR2 and EBT3 Radiochromic film were placed around the periphery of the phantom, and OSLs were placed every 30° around the phantom periphery to determine output and surface dose uniformity. A piece of Kodak EDR2 was sandwiched between the two slabs of the 30 cm diameter phantom to determine beam penetration. Results: Field uniformity shifting the patient ±75 cm was ±5% over a treatment span of 190 cm. The dose variation around the periphery of the 30 cm diameter phantom varied by <±5% with the maximum values observed at the 0°-300°, 60° locations with the minimum values at the 30°-330°, 60° locations. Results obtained using Kodak EDR2, EBT3 Radiochromic film, and OSLs agreed to within ±5%. Conclusion: This technique provides a very efficient and convenient means by which to treat the entire skin surface of patients incapable of standing for treatment. It provides a treatment field that is both large and uniform enough for adults along with a convenient way to treat four of the six patient treatment positions. The beam spoiler lies to the side of the patient allowing easy access for patient positioning.
-
Diffusion Region's Structure at the Subsolar Magnetopause with MMS Data
Cozzani, G.; Retino, A.; Califano, F.; Alexandrova, A.; Catapano, F.; Fu, H.; Le Contel, O.; Khotyaintsev, Y. V.; Vaivads, A.; Ahmadi, N.; Lindqvist, P. A.; Breuillard, H.; Mirioni, L.; Ergun, R.; Torbert, R. B.; Giles, B. L.; Russell, C. T.; Nakamura, R.; Moore, T. E.; Fuselier, S. A.; Mauk, B.; Burch, J.
2017-12-01
Magnetic reconnection occurs in the magnetosphere in thin current sheets, where a change in the magneticfield topology leads to rapid conversion of magnetic energy into ion and electron energy. To allow for magneticfield reconfiguration, both ions and electrons have to become demagnetized in the ion and electron diffusionregions, respectively. MMS spacecraft observations at inter-spacecraft separation ˜ 10 km (correspondingto ˜ 5 d_e at the magnetopause) allow, for the first time, to make multi-point studies of the structure of theelectron diffusion region (EDR). We present MMS observations on January,27th 2017 of one magnetopausecrossing close to the subsolar point showing several signatures consistent with an EDR encounter nearbya magnetic field minimum. The proximity to the reconnection site is further substantiated by the FirstOrder Taylor Expansion (FOTE) method applied to the magnetic field data. Observations suggest that allspacecraft passed through the EDR. Despite of the small inter-spacecraft separation (7 km), the observationsshow important differences among spacecraft. We focus on the comparison between MMS3 and MMS4 sincethey show the most striking differences. MMS3 measures a stronger parallel electron heating and highercurrent densities than MMS4. Both satellites observe crescent-shaped electron distribution functions on themagnetospheric side but MMS4 observes them over a longer time interval. These observations suggest thatMMS3 is passing closer to the reconnection site than MMS4. The differences between the observations by thetwo spacecraft indicate that the EDR is rather structured over scales of a few electron inertial lengths. Wealso evaluate the Generalized Ohm's law and find that the electric field is mainly balanced by the divergenceof the electron pressure tensor while the electron inertia term is negligible.
-
Energy Technology Data Exchange (ETDEWEB)
Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.; Kukhto, V. A.; Tarasyuk, V. T.; Filippovich, V. P. [All-Russia Research Institute of Preservation Technology (Russian Federation); Egorkin, A. V.; Chasovskikh, A. V. [Research Institute of Technical Physics and Automation (Russian Federation); Pavlov, Yu. S., E-mail: rad05@bk.ru [Frumkin Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences (Russian Federation); Prokopenko, A. V., E-mail: pav14@mail.ru [National Research Nuclear University (Moscow Engineering Physics Institute) (Russian Federation); Strokova, N. E. [Moscow State University (Russian Federation); Artem’ev, S. A. [Russian Research Institute of Baking Industry (Russian Federation); Polyakova, S. P. [Russian Research Institute of Confectionery Industry (Russian Federation)
2016-12-15
The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.
-
International Nuclear Information System (INIS)
Gracheva, A. Yu.; Zav’yalov, M. A.; Ilyukhina, N. V.; Kukhto, V. A.; Tarasyuk, V. T.; Filippovich, V. P.; Egorkin, A. V.; Chasovskikh, A. V.; Pavlov, Yu. S.; Prokopenko, A. V.; Strokova, N. E.; Artem’ev, S. A.; Polyakova, S. P.
2016-01-01
The work is dedicated to improvement of efficiency of storage and processing of food raw materials using radiation technologies. International practice of radiation processing of food raw materials is presented and an increase in the consumption of irradiated food products is shown. The prospects of using radiation technologies for the processing of food products in Russia are discussed. The results of studies of radiation effects on various food products and packaging film by γ radiation and accelerated electrons are presented.
-
Small-Scale Dayside Magnetic Reconnection Analysis via MMS
Pritchard, K. R.; Burch, J. L.; Fuselier, S. A.; Webster, J.; Genestreti, K.; Torbert, R. B.; Rager, A. C.; Phan, T.; Argall, M. R.; Le Contel, O.; Russell, C. T.; Strangeway, R. J.; Giles, B. L.
2017-12-01
The Magnetospheric Multiscale (MMS) mission has the primary objective of understanding the physics of the reconnection electron diffusion region (EDR), where magnetic energy is transformed into particle energy. In this poster, we present data from an EDR encounter that occurred in late December 2016 at approximately 11:00 MLT with a moderate guide field. The spacecraft were in a tetrahedral formation with an average inter-spacecraft distance of approximately 7 kilometers. During this event electron crescent-shaped distributions were observed in the electron stagnation region as is typical for asymmetric reconnection. Based on the observed ion velocity jets, the spacecraft traveled just south of the EDR. Because of the close spacecraft separation, fairly accurate computation of the Hall, electron pressure divergence, and electron inertia components of the reconnection electric field could be made. In the region of the crescent distributions good agreement was observed, with the strongest component being the normal electric field and the most significant sources being electron pressure divergence and the Hall electric field. While the strongest currents were in the out-of-plane direction, the dissipation was strongest in the normal direction because of the larger magnitude of the normal electric field component. These results are discussed in light of recent 3D PIC simulations performed by other groups.
-
Output calculation of electron therapy at extended SSD using an improved LBR method
Energy Technology Data Exchange (ETDEWEB)
Alkhatib, Hassaan A.; Gebreamlak, Wondesen T., E-mail: wondtassew@gmail.com; Wright, Ben W.; Neglia, William J. [South Carolina Oncology Associates, Columbia, South Carolina 29210 (United States); Tedeschi, David J. [Department of Physics and Astronomy, University of South Carolina, Columbia, South Carolina 29208 (United States); Mihailidis, Dimitris [CAMC Cancer Center and Alliance Oncology, Charleston, West Virginia 25304 (United States); Sobash, Philip T. [The Medical University of South Carolina, Charleston, South Carolina 29425 (United States); Fontenot, Jonas D. [Department of Physics, Mary Bird Perkins Cancer Center, Baton Rouge, Louisiana 70809 (United States)
2015-02-15
Purpose: To calculate the output factor (OPF) of any irregularly shaped electron beam at extended SSD. Methods: Circular cutouts were prepared from 2.0 cm diameter to the maximum possible size for 15 × 15 applicator cone. In addition, two irregular cutouts were prepared. For each cutout, percentage depth dose (PDD) at the standard SSD and doses at different SSD values were measured using 6, 9, 12, and 16 MeV electron beam energies on a Varian 2100C LINAC and the distance at which the central axis electron fluence becomes independent of cutout size was determined. The measurements were repeated with an ELEKTA Synergy LINAC using 14 × 14 applicator cone and electron beam energies of 6, 9, 12, and 15 MeV. The PDD measurements were performed using a scanning system and two diodes—one for the signal and the other a stationary reference outside the tank. The doses of the circular cutouts at different SSDs were measured using PTW 0.125 cm{sup 3} Semiflex ion-chamber and EDR2 films. The electron fluence was measured using EDR2 films. Results: For each circular cutout, the lateral buildup ratio (LBR) was calculated from the measured PDD curve using the open applicator cone as the reference field. The effective SSD (SSD{sub eff}) of each circular cutout was calculated from the measured doses at different SSD values. Using the LBR value and the radius of the circular cutout, the corresponding lateral spread parameter [σ{sub R}(z)] was calculated. Taking the cutout size dependence of σ{sub R}(z) into account, the PDD curves of the irregularly shaped cutouts at the standard SSD were calculated. Using the calculated PDD curve of the irregularly shaped cutout along with the LBR and SSD{sub eff} values of the circular cutouts, the output factor of the irregularly shaped cutout at extended SSD was calculated. Finally, both the calculated PDD curves and output factor values were compared with the measured values. Conclusions: The improved LBR method has been generalized to
-
Directory of Open Access Journals (Sweden)
Dmitry Alexandrovich Izotov
2013-12-01
Full Text Available Deficit of raw materials is becoming an important concern for the Chinese economy as it continues to grow. This deficit is amended with imports, which – in their own turn – are limited by the high level of global prices. The build-up issue of raw materials imports is going to solve by the measures of monetary policy (RMB’s revaluation against the USD. Analysis of China’s market of raw materials reveals that the largest increase in the physical volume of imports is concentrated in crude oil, LNG, iron ore and coal. As for Russia, its supplies and share in total Chinese imports of raw materials tend to increase. Author employs regression equations based on international statistics data to show that RMB’s revaluation, ceteris paribus, increases physical volumes of raw materials imports. However, the main factor of coal and LNG imports growth is energy consumption by Chinese heavy industry; imports of oil products – producers’ prices; meanwhile imports of steel products tend to decrease with the growth of steel exports. RMB’s revaluation increases physical volumes of imports of low value added raw materials from Russia (coal, crude oil, iron ore
-
Cardiotoxic Effects of Raw Opium.
Garg, Piyush; Hitawala, Asif Ali; Agarwal, Manoj
2018-01-01
While opioid drug toxicity and side effects of long-term opioid use during medical care are well studied, there is little information regarding effects of ingestion of raw opium. Characterization of the effects to a particular alkaloid is difficult since raw opium contains a number of alkaloids. Here, we present a case of poisoning due to ingestion of raw opium leading to severe myocardial suppression.
-
Cardiotoxic Effects of Raw Opium
Garg, Piyush; Hitawala, Asif Ali; Agarwal, Manoj
2018-01-01
While opioid drug toxicity and side effects of long-term opioid use during medical care are well studied, there is little information regarding effects of ingestion of raw opium. Characterization of the effects to a particular alkaloid is difficult since raw opium contains a number of alkaloids. Here, we present a case of poisoning due to ingestion of raw opium leading to severe myocardial suppression.
-
Mining Pribram in science and technology. Proceedings of Session U - Mineral raw materials treatment
International Nuclear Information System (INIS)
Tomasek, J.; Vetejska, K.
1987-01-01
The proceedings of session ''Mineral raw materials treatment'' contain 27 papers of which only one deals with the application of nuclear technology, namely, the effect of fast electrons on the magnetic properties of the polymetallic Rudniany ore. (J.B.)
-
Das, B.; Wilson, M.; Divakarla, M. G.; Chen, W.; Barnet, C.; Wolf, W.
2013-05-01
Algorithm Development Library (ADL) is a framework that mimics the operational system IDPS (Interface Data Processing Segment) that is currently being used to process data from instruments aboard Suomi National Polar-orbiting Partnership (S-NPP) satellite. The satellite was launched successfully in October 2011. The Cross-track Infrared and Microwave Sounder Suite (CrIMSS) consists of the Advanced Technology Microwave Sounder (ATMS) and Cross-track Infrared Sounder (CrIS) instruments that are on-board of S-NPP. These instruments will also be on-board of JPSS (Joint Polar Satellite System) that will be launched in early 2017. The primary products of the CrIMSS Environmental Data Record (EDR) include global atmospheric vertical temperature, moisture, and pressure profiles (AVTP, AVMP and AVPP) and Ozone IP (Intermediate Product from CrIS radiances). Several algorithm updates have recently been proposed by CrIMSS scientists that include fixes to the handling of forward modeling errors, a more conservative identification of clear scenes, indexing corrections for daytime products, and relaxed constraints between surface temperature and air temperature for daytime land scenes. We have integrated these improvements into the ADL framework. This work compares the results from ADL emulation of future IDPS system incorporating all the suggested algorithm updates with the current official processing results by qualitative and quantitative evaluations. The results prove these algorithm updates improve science product quality.
-
Characterization of silica quartz as raw material in photovoltaic applications
Energy Technology Data Exchange (ETDEWEB)
Boussaa, S. Anas, E-mail: sabiha.anas@gmail.com; Kheloufi, A.; Kefaifi, A.; Kerkar, F. [Division croissance cristalline et procédés métallurgiques CCPM Centre de recherche en technologie des semi-conducteurs pour l’énergétique (C.R.T.S.E) 02 Bd Frantz Fanon BP. 140 Alger 7 merveilles, Alger 16200 (Algeria); Zaourar, N. Boutarek [Laboratoire des technologies des matériaux, USTHB, B.P. 32 El Alia, Bab Ezzouar, Alger, Algérie 16111 (Algeria)
2016-07-25
Raw materials are essential for the functioning of modern societies, and access to these raw materials is vital to the world economy. Sustainable development, both globally level, raises important new challenges associated with access and efficient use of raw materials. High purity quartz, is consider as a critical raw material and it is a rare commodity that only forms under geological conditions where a narrow set of chemical and physical parameters is fulfilled. When identified and following special beneficiation techniques, high purity quartz obtains very attractive prices and is applied in high technology sectors that currently are under rapid expansion such as photovoltaic solar cells, silicon metal - oxide wafers in the semiconductor industry and long distance optical fibers that are used in communication networks. Crystalline silicon remains the principal material for photovoltaic technology. Metallurgical silicon is produced industrially by the reduction of silica with carbon in an electric arc furnace at temperatures higher than 2000 °C in the hottest parts, by a reaction that can be written ideally as: SiO{sub 2} + 2C = Si + 2CO. The aim of this study has been to test experimental methods for investigating the various physical and chemical proprieties of Hoggar quartz with different techniques: X Ray Fluorescence, infra-red spectroscopy, Scanning Electron Microscopy, Optic Microscopy, Carbon Analyzer and Vickers Hardness. The results show finally that the quartz has got good result in purity but need enrichment for the photovoltaic application.
-
International Nuclear Information System (INIS)
Arnold, O.
1975-01-01
In this paper some aspects are being considered, in as far as they can contribute to a better understanding of uranium as a raw material and an energy carrier, and as they can indicate the possible ways and means open to the German Federal Republic for securing this highly desirable raw material, without becoming even more dependent on the economic and political views of the producing countries, than it is the case in respect of oil. (orig.) [de
-
DEFF Research Database (Denmark)
Walford, Antonia
2017-01-01
. Although science and technology studies (STS) makes a strong case for associating relationality with certainty, the article argues that a particular form of data, ‘raw data’, complicates this association. It further argues that scientific data is not simply composed out of relations, but is a relation......This article takes scientific ‘raw data’ as its ethnographic object in order to investigate the co-implication of nature and culture in scientific knowledge practices. The article traces out some of the activities that are involved in producing numerical climate data from the Brazilian Amazon...... itself. The article ends with a brief reflection on the possible repercussions of shifting from thinking of science as producing multiple natures and cultures to thinking of it as producing the potential for relations....
-
International Nuclear Information System (INIS)
Moreno, Maria Margarita Torres; Rocha, Rogers Raphael da; Zanard, Antenor
2012-01-01
We studied the raw materials used in a factory building blocks, located in Cesario Lange city (SP). It extracts raw materials from various sources in the region to make the dough. The mixtures were prepared from dry milled powders based on data related to the plasticity of the raw materials. It was obtained with the apparatus Vicat-cone in order to obtain similar levels of water absorption of the samples burned at 900 deg C for all compositions. To quantify the proportion of each clay was used the Lever Rule. In this firing temperature, where sintering is mainly by diffusion from a solid state, different compositions of the same set of four raw materials resulted in similar values. (author)
-
Energy Technology Data Exchange (ETDEWEB)
Lobo, A.O., E-mail: loboao@yahoo.com [Laboratorio Associado de Sensores e Materiais, INPE, Sao Jose dos Campos/SP (Brazil); Instituto Tecnologico de Aeronautica, ITA, Sao Jose dos Campos/SP (Brazil); Laboratorio de Nanotecnologia Biomedica, Universidade do Vale do Paraiba, Sao Jose dos Campos/SP (Brazil); Corat, M.A.F. [Centro Multidisciplinar para Investigacao Biologica na Area da Ciencia em Animais de Laboratorio, CEMIB, UNICAMP, Campinas/SP (Brazil); Antunes, E.F. [Laboratorio Associado de Sensores e Materiais, INPE, Sao Jose dos Campos/SP (Brazil); Instituto Tecnologico de Aeronautica, ITA, Sao Jose dos Campos/SP (Brazil); Ramos, S.C. [Instituto Tecnologico de Aeronautica, ITA, Sao Jose dos Campos/SP (Brazil); Pacheco-Soares, C. [Laboratorio de Dinamica de Compartimentos Celulares, UNIVAP, Sao Jose dos Campos/SP (Brazil); and others
2012-05-01
It was presented a strong difference on cell adhesion and proliferation of functionalized vertically-aligned multi-walled carbon nanotube (VACNT) scaffolds compared to raw-VACNT. Biocompatibility in vitro tests were performed on raw-VACNT after superficial modification by oxygen plasma, which changes its superhydrophobic character to superhydrophilic. Two cytocompatibility tests were applied: 1) total lactate dehydrogenase colorimetric assay for the study of proliferating cells; and 2) cellular adhesion by scanning electron microscopy. Results showed that superhydrophilic VACNT scaffolds stimulate cell growth with proliferation up to 70% higher than normal growth of cell culture.
-
Effects of limestone petrography and calcite microstructure on OPC clinker raw meals burnability
Galimberti, Matteo; Marinoni, Nicoletta; Della Porta, Giovanna; Marchi, Maurizio; Dapiaggi, Monica
2017-10-01
Limestone represents the main raw material for ordinary Portland cement clinker production. In this study eight natural limestones from different geological environments were chosen to prepare raw meals for clinker manufacturing, aiming to define a parameter controlling the burnability. First, limestones were characterized by X-Ray Fluorescence, X-Ray Powder Diffraction and Optical Microscopy to assess their suitability for clinker production and their petrographic features. The average domains size and the microstrain of calcite were also determined by X-Ray Powder Diffraction line profile analysis. Then, each limestone was admixed with clay minerals to achieve the adequate chemical composition for clinker production. Raw meals were thermally threated at seven different temperatures, from 1000 to 1450 °C, to evaluate their behaviour on heating by ex situ X-Ray Powder Diffraction and to observe the final clinker morphology by Scanning Electron Microscopy. Results indicate the calcite microstrain is a reliable parameter to predict the burnability of the raw meals, in terms of calcium silicates growth and lime consumption. In particular, mixtures prepared starting from high-strained calcite exhibit a better burnability. Later, when the melt appears this correlation vanishes; however differences in the early burnability still reflect on the final clinker composition and texture.
-
CO2 Capture by Cement Raw Meal
DEFF Research Database (Denmark)
Pathi, Sharat Kumar; Lin, Weigang; Illerup, Jytte Boll
2013-01-01
The cement industry is one of the major sources of CO2 emissions and is likely to contribute to further increases in the near future. The carbonate looping process has the potential to capture CO2 emissions from the cement industry, in which raw meal for cement production could be used...... as the sorbent. Cyclic experiments were carried out in a TGA apparatus using industrial cement raw meal and synthetic raw meal as sorbents, with limestone as the reference. The results show that the CO2 capture capacities of the cement raw meal and the synthetic raw meal are comparable to those of pure limestone...... that raw meal could be used as a sorbent for the easy integration of the carbonate looping process into the cement pyro process for reducing CO2 emissions from the cement production process....
-
Food safety hazards associated with consumption of raw milk.
Oliver, Stephen P; Boor, Kathryn J; Murphy, Steven C; Murinda, Shelton E
2009-09-01
An increasing number of people are consuming raw unpasteurized milk. Enhanced nutritional qualities, taste, and health benefits have all been advocated as reasons for increased interest in raw milk consumption. However, science-based data to substantiate these claims are limited. People continue to consume raw milk even though numerous epidemiological studies have shown clearly that raw milk can be contaminated by a variety of pathogens, some of which are associated with human illness and disease. Several documented milkborne disease outbreaks occurred from 2000-2008 and were traced back to consumption of raw unpasteurized milk. Numerous people were found to have infections, some were hospitalized, and a few died. In the majority of these outbreaks, the organism associated with the milkborne outbreak was isolated from the implicated product(s) or from subsequent products made at the suspected dairy or source. In contrast, fewer milkborne disease outbreaks were associated with consumption of pasteurized milk during this same time period. Twenty nine states allow the sale of raw milk by some means. Direct purchase, cow-share or leasing programs, and the sale of raw milk as pet food have been used as means for consumers to obtain raw milk. Where raw milk is offered for sale, strategies to reduce risks associated with raw milk and products made from raw milk are needed. Developing uniform regulations including microbial standards for raw milk to be sold for human consumption, labeling of raw milk, improving sanitation during milking, and enhancing and targeting educational efforts are potential approaches to this issue. Development of pre- and postharvest control measures to effectively reduce contamination is critical to the control of pathogens in raw milk. One sure way to prevent raw milk-associated foodborne illness is for consumers to refrain from drinking raw milk and from consuming dairy products manufactured using raw milk.
-
Structural analysis of raw and commercial farm edible bird nests.
Kew, P E; Wong, S F; Lim, P K; Mak, J W
2014-03-01
Edible bird nests (EBNs) are consumed worldwide for various health benefits. EBNs are nests built from the saliva of swiftlets of Aerodramus species. The global market for EBNs is on the rise, especially from Hong Kong and mainland China. In the past, EBNs were harvested mainly from natural caves; however in the recent years, there has been a rapid growth of swiftlet farming. Little is known about the actual composition of EBNs except for protein, carbohydrate, ash and lipid contents, amino acids, vitamins and macro/ micronutrients. Besides the biochemical components of EBNs, are there any other structures that are associated with EBNs? This paper reports on the structural analysis of raw unprocessed farm and processed commercial EBNs. The raw EBNs were purchased from swiftlet farms in five locations in Peninsula Malaysia: Kuala Sanglang (Perlis; 6° 16' 0"N, 100° 12' 0"E), Pantai Remis (Perak; 4º 27' 0" N, 100º 38' 0" E), Kluang (Johor; 02º 012 303N 103º 192 583E), Kajang (Selangor; 2º 59' 0"N, 101º 47' 0"E) and Kota Bharu (Kelantan; 6º 8' 0"N, 102º 15' 0"E). The commercial nests were purchased from five different Chinese traditional medicinal shops (Companies A-E). A portion of each EBN was randomly broken into small fragments, attached to carbon tape and coated with gold and palladium particles for examination and photography under a scanning electron microscope. Structural analysis revealed the presence of mites, fungi, bacteria and feather strands on both the raw and commercial nests. Mite eggshells and faecal pellets, and body parts of other arthropods were seen only in the raw nests. The commercial nests had a variety of unidentified structures and substances coated on the nests' surfaces that were not found on the raw nests. The presence of these contaminants may jeopardise the quality of EBNs and pose health risks to consumers. Further identification of the mites and their allergens, fungi and bacteria are on-going and will be reported separately.
-
Ramsahoi, L; Gao, A; Fabri, M; Odumeru, J A
2011-07-01
Automated electronic milk analyzers for rapid enumeration of total bacteria counts (TBC) are widely used for raw milk testing by many analytical laboratories worldwide. In Ontario, Canada, Bactoscan flow cytometry (BsnFC; Foss Electric, Hillerød, Denmark) is the official anchor method for TBC in raw cow milk. Penalties are levied at the BsnFC equivalent level of 50,000 cfu/mL, the standard plate count (SPC) regulatory limit. This study was conducted to assess the BsnFC for TBC in raw goat milk, to determine the mathematical relationship between the SPC and BsnFC methods, and to identify probable reasons for the difference in the SPC:BsnFC equivalents for goat and cow milks. Test procedures were conducted according to International Dairy Federation Bulletin guidelines. Approximately 115 farm bulk tank milk samples per month were tested for inhibitor residues, SPC, BsnFC, psychrotrophic bacteria count, composition (fat, protein, lactose, lactose and other solids, and freezing point), and somatic cell count from March 2009 to February 2010. Data analysis of the results for the samples tested indicated that the BsnFC method would be a good alternative to the SPC method, providing accurate and more precise results with a faster turnaround time. Although a linear regression model showed good correlation and prediction, tests for linearity indicated that the relationship was linear only beyond log 4.1 SPC. The logistic growth curve best modeled the relationship between the SPC and BsnFC for the entire sample population. The BsnFC equivalent to the SPC 50,000 cfu/mL regulatory limit was estimated to be 321,000 individual bacteria count (ibc)/mL. This estimate differs considerably from the BsnFC equivalent for cow milk (121,000 ibc/mL). Because of the low frequency of bulk tank milk pickups at goat farms, 78.5% of the samples had their oldest milking in the tank to be 6.5 to 9.0 d old when tested, compared with the cow milk samples, which had their oldest milking at 4 d
-
Directory of Open Access Journals (Sweden)
Wiwik Sudarwati
2017-07-01
Full Text Available The raw material inventory control system determines and guarantees the availability of raw material stock in the right quantity quality and timing. The problem in this research is the procurement of raw materials of tobacco. PR. Sukun still often experiences the excess. This is related to the frequency of raw material purchases and the quantity of raw material purchases which can lead to waste of working capital embedded in raw material inventory raw material ordering costs and raw material storage costs. The purpose of this research is to know how to make an efficiency level in procurement of raw material inventory between EOQ method compared with policy of PR. Sukun. The type of research used is analytic descriptive type. Data analysis begins by analyzing raw material quantity comparison total raw material inventory cost and raw material cost between PR Sukun policy with EOQ method. Based on the results of research known that by using EOQ method can be much more efficient compared to policy of PR. Sukun. The quantity and frequency of purchasing raw materials is less but still take into account the safety stock and reorder point so the production process is not disturbed. In addition the cost of purchasing ordering costs and raw materials storage costs less so as to create efficiencies on the cost of raw materials inventory. PR. Sukun in the procurement of raw material inventory should use EOQ method to be more efficient and take into account the safety stock and reorder point to avoid the inventory excess of raw materials.
-
SAR Raw Data Generation for Complex Airport Scenes
Directory of Open Access Journals (Sweden)
Jia Li
2014-10-01
Full Text Available The method of generating the SAR raw data of complex airport scenes is studied in this paper. A formulation of the SAR raw signal model of airport scenes is given. Via generating the echoes from the background, aircrafts and buildings, respectively, the SAR raw data of the unified SAR imaging geometry is obtained from their vector additions. The multipath scattering and the shadowing between the background and different ground covers of standing airplanes and buildings are analyzed. Based on the scattering characteristics, coupling scattering models and SAR raw data models of different targets are given, respectively. A procedure is given to generate the SAR raw data of airport scenes. The SAR images from the simulated raw data demonstrate the validity of the proposed method.
-
Takahashi, Hisashi; Goto, Taiga; Hirokawa, Koichi; Miyazaki, Osamu
2014-03-01
Statistical iterative reconstruction and post-log data restoration algorithms for CT noise reduction have been widely studied and these techniques have enabled us to reduce irradiation doses while maintaining image qualities. In low dose scanning, electronic noise becomes obvious and it results in some non-positive signals in raw measurements. The nonpositive signal should be converted to positive signal so that it can be log-transformed. Since conventional conversion methods do not consider local variance on the sinogram, they have difficulty of controlling the strength of the filtering. Thus, in this work, we propose a method to convert the non-positive signal to the positive signal by mainly controlling the local variance. The method is implemented in two separate steps. First, an iterative restoration algorithm based on penalized weighted least squares is used to mitigate the effect of electronic noise. The algorithm preserves the local mean and reduces the local variance induced by the electronic noise. Second, smoothed raw measurements by the iterative algorithm are converted to the positive signal according to a function which replaces the non-positive signal with its local mean. In phantom studies, we confirm that the proposed method properly preserves the local mean and reduce the variance induced by the electronic noise. Our technique results in dramatically reduced shading artifacts and can also successfully cooperate with the post-log data filter to reduce streak artifacts.
-
Raw materials policy: implications for Germany
Energy Technology Data Exchange (ETDEWEB)
Gaertner, E
1978-04-01
The contribution characterizes the situation of the national mining industry in 1977, deals with international raw materials policies within the framework of the North-South dialogue and with the policies of the western industrial countries, points out the dangers of worldwide state-controlled raw materials policies and calls for a) the political risk of enterprise cooperation with developing countries to be covered and b) double taxation to be avoided. Finally, the problems of securing the Federal Republic of Germany's raw materials supplies on a long-term basis are portrayed.
-
Quality and Sensorial Characteristics of Raw-Vegan Bars
Directory of Open Access Journals (Sweden)
Liana Claudia Salanţă
2015-11-01
Full Text Available Increased consumer interest in healthier food products is driven by a variety of factors including growing awareness of the link between diet and health, the desire to age ‘gracefully’ by maintaining good health, greater convenience in meeting nutritional needs and preventing chronic diseases. In raw food diet, food is consumed predominantly or exclusively as uncooked and unprocessed raw food; the main components of the diet are fruits, nuts, seeds, and sprouted grains and beans. The aim of this study was to obtain two raw-vegan bars using dry raw materials and to establish the physicochemical and sensory characteristics of the products. Raw-vegan bars were formulated using fruits and seeds (cranberries, figs, raisins, raspberries, cashew, chia seeds, etc. and binding agents (honey. Raw-vegan bars stands out among fast foods due to their balanced nutritional content and convenience.
-
Radiation decontamination (hygienisation) of cosmetic raw materials and products
International Nuclear Information System (INIS)
Malec-Czechowska, K.; Migdal, W.; Owczarczyk, H.B.
1998-01-01
Microbiological purity of cosmetics is a problem of today because of growing hygienic requirements to these products. The demand for high hygienic purity from one side and the limitation in the use of conservants to cosmetics from the other side stimulate the research activity, the aim of which is to satisfy present requirements in this field. The application of radiation decontamination (hygienisation) seems to be one of solutions. In present report were present the results of the study on the effect of electron beam irradiation on microbial contamination of selected cosmetics and some raw materials used in cosmetic industry. Radiation doses applied were not higher than 6.0 kGy. The level of microbial contamination in both unirradiated and irradiated samples was determined by applying the standard microbiological methods. In addition, the quality and usefulness of irradiated cosmetics were examined by methods used in cosmetic industry. The results obtained show conclusively that radiation treatment can be successfully used for the decontamination (hygienisation) of cosmetics and some raw materials used in their production, without changing the quality and the usefulness of the product released. (author)
-
Survey to determine why people drink raw milk.
Mullin, Gerard E; Belkoff, Stephen M
2014-11-01
Fragility fractures associated with osteoporosis extract a large financial and personal toll on society. Pharmaceutical or dietary calcium intake is needed to increase bone mineral density to prevent fragility fractures. Although dairy products are a good source of calcium, patients who are unable to digest lactose tend to avoid them and are put at a greater risk for fracture than the general population. Anecdotal reports suggest that lactose maldigesters, when consuming raw milk, have a dramatic reduction in symptoms relative to pasteurized milk. The mechanism of the reported reduction in symptoms, if true, is unknown. The purpose of the current study was to survey raw milk drinkers to ascertain their health-related motivations for consuming raw milk, especially as they relate to lactose maldigestion. An online survey regarding raw milk was completed by 153 of 1527 members of a raw milk-buying community. The primary reason the respondents cited for drinking raw milk was that they believed it was more healthful; 30% reported some gastrointestinal discomfort when drinking pasteurized milk, yet almost all (99%) reported consuming raw milk without discomfort. Despite the reports of gastrointestinal discomfort, only 5% of respondents had been diagnosed as lactose intolerant by a medical professional, and only 1% had been diagnosed as lactose intolerant via the gold-standard hydrogen breath test. The primary motivation for drinking raw milk is its perceived health value, not its digestibility. Although raw milk appears to be more easily digested than pasteurized milk in our survey sample, the mechanism of digestibility remains unknown.
-
Microbial production of raw starch digesting enzymes | Sun | African ...
African Journals Online (AJOL)
Raw starch digesting enzymes refer to enzymes that can act directly on raw starch granules below the gelatinization temperature of starch. With the view of energy-saving, a worldwide interest has been focused on raw starch digesting enzymes in recent years, especially since the oil crisis of 1973. Raw starch digesting ...
-
Gabarrón, S; Gernjak, W; Valero, F; Barceló, A; Petrovic, M; Rodríguez-Roda, I
2016-05-15
Emerging contaminants (EC) have gained much attention with globally increasing consumption and detection in aquatic ecosystems during the last two decades from ng/L to lower ug/L. The aim of this study was to evaluate the occurrence and removal of pharmaceutically active compounds (PhACs), endocrine disrupting chemicals (EDCs) and related compounds in a Drinking Water Treatment Plant (DWTP) treating raw water from the Mediterranean Llobregat River. The DWTP combined conventional treatment steps with the world's largest electrodialysis reversal (EDR) facility. 49 different PhACs, EDCs and related compounds were found above their limit of quantification in the influent of the DWTP, summing up to a total concentration of ECs between 1600-4200 ng/L. As expected, oxidation using chlorine dioxide and granular activated carbon filters were the most efficient technologies for EC removal. However, despite the low concentration detected in the influent of the EDR process, it was also possible to demonstrate that this process partially removed ionized compounds, thereby constituting an additional barrier against EC pollution in the product. In the product of the EDR system, only 18 out of 49 compounds were quantifiable in at least one of the four experimental campaigns, showing in all cases removals higher than 65% and often beyond 90% for the overall DWTP process. Copyright © 2016 Elsevier B.V. All rights reserved.
-
CSIR Research Space (South Africa)
Joseph, S
2010-01-01
Full Text Available in the permeability of the membrane and HO H3C H3C H2C H2C HO OH NH NH OH O OC C n O O O O Fig. 4 Structure of Chitin Raw and Renewable Polymers promoting internal osmotic imbalances. This results in leaching of electrolytes and proteins. 2... is often lost. In most cases this denaturation is not reversible. R-CH-COOH NH2 w Amino acid H2N COOHR a Amino acid Fig. 5 Structure of amino acid Raw and Renewable Polymers The solubilities of proteins vary considerably based on compositions...
-
Quality quantification model of basic raw materials
Directory of Open Access Journals (Sweden)
Š. Vilamová
2016-07-01
Full Text Available Basic raw materials belong to the key input sources in the production of pig iron. The properties of basic raw materials can be evaluated using a variety of criteria. The essential ones include the physical and chemical properties. Current competitive pressures, however, force the producers of iron more and more often to include cost and logistic criteria into the decision-making process. In this area, however, they are facing a problem of how to convert a variety of vastly different parameters into one evaluation indicator in order to compare the available raw materials. This article deals with the analysis of a model created to evaluate the basic raw materials, which was designed as part of the research.
-
Data extraction from proteomics raw data
DEFF Research Database (Denmark)
Mancuso, Francesco; Bunkenborg, Jakob; Wierer, Michael
2012-01-01
In shot-gun proteomics raw tandem MS data are processed with extraction tools to produce condensed peak lists that can be uploaded to database search engines. Many extraction tools are available but to our knowledge, a systematic comparison of such tools has not yet been carried out. Using raw data...
-
Factors affecting adherence to a raw vegan diet
Link, Lilli B.; Jacobson, Judith S.
2007-01-01
The purpose of this study was to evaluate adherence and identify predictors of adherence to a raw vegan diet (i.e., uncooked plant foods) following a stay at a raw vegan institute. In this cohort study of guests at a raw vegan institute, subjects completed written questionnaires upon arrival and 12 weeks later. Of 107 eligible guests, 84 participated. Mean age was 54 years, 23 were male, and 73 white. Fifty-one completed the 12-week follow-up. Eight (16%) reported their diet to be ≥80% raw ve...
-
Effects of gamma irradiation on raw materials and perfumes
International Nuclear Information System (INIS)
Guillot, M.; Pelpel, A.
1983-01-01
In order to enlight the strange problem of apparent perfume stability observed in manufactured talc powders sterilized by gamma rays, investigations were made on samples of odorant substances (raw materials, essential oils, or elaborated mixtures). As a rule, no immediate adulteration of olfactive caracteristics resulted at once from gamma irradiation. In several cases, a stabilizing effect appeared immediately and remained effective after long storage in various conditions (of temperature, or light, or oxygen exposure). This unexpected effect seems to be in accordance with previous experiments on gamma or electron irradiations of mixtures of organic molecules, reported in litterature: a mutual inhibition was observed to take place [fr
-
Improving the raw management in Ukraine
Energy Technology Data Exchange (ETDEWEB)
Jung, H.G.; Koever, M. [NUKEM Technologies GmbH, Alzenau (Germany)
2013-07-01
In Ukraine 13 VVER-1000 and 2 VVER-440 reactor units generate about 50 % of the country's energy production. By contrast, when looking at the large volume of radioactive waste of all categories, which is produced by these nuclear power plants (NPP), the radioactive waste (RAW) management - onsite of NPP, towards interim storage as well as towards final disposal - is still not adequately developed. Currently all operational waste of Ukrainian NPP is incompletely treated/conditioned and stored onsite, though insufficient storage capacity is available at the NPP. As no effective Ukraine-wide strategy is yet established to manage RAW beyond NPP a serious situation could arise, which even leads to constrained temporary shut-down of reactor units, threatening the energy supply of whole the country. In addition large quantities of RAW, partly badly sorted, derive from decommissioning of the shut-down Chernobyl NPP. Also other sources of RAW contribute to the whole volume, which has to be managed in Ukraine, as research reactors, reprocessing of spent nuclear fuel and other nuclear facilities and applications. Nevertheless, operational and shut-down NPP in Ukraine are by far the largest producers. To support Ukraine in managing their radioactive waste NUKEM Technologies GmbH was appointed to provide technical support for the improvement of the current situation in cooperation with responsible Ukrainian experts towards a targeted, comprehensive and effective RAW management. (orig.)
-
Characterization of raw materials to obtain the mass for white ware, using waste glass
International Nuclear Information System (INIS)
Cavalcanti, M.S.L.; Porto, V.S.; Meneses, R.L; Albuquerque, A.V.; Guedes, B.F.R.; Morais, C.R.S.; Santana, L.N.L.
2009-01-01
A major problem faced in the post modern society is the huge amount of glass, accumulated in landfills cities. The glass material is one hundred percent recyclable and has the property to act as fluxes as well as feldspar. Given this premise, this study aimed to characterize materials - raw materials and waste glass regional plan for development of ceramic bodies with the similar behavior produced industrially, using shards of glass to partially replace the feldspar. The materials - raw materials used were clay, ball clay, kaolin, quartz, feldspar and shard of glass, being characterized by the techniques: chemical analysis, size analysis, differential thermal analysis vibrational spectroscopy in the infrared region, the Ray-Diffraction X and scanning electron microscopy. The results showed that the waste had higher rates of vitreous oxides fluxes and similar. (author)
-
Lin, Hai-Juan; Xian, Liang; Zhang, Qiu-Jiang; Luo, Xue-Mei; Xu, Qiang-Sheng; Yang, Qi; Duan, Cheng-Jie; Liu, Jun-Liang; Tang, Ji-Liang; Feng, Jia-Xun
2011-06-01
A newly isolated strain Penicillium sp. GXU20 produced a raw starch-degrading enzyme which showed optimum activity towards raw cassava starch at pH 4.5 and 50 °C. Maximum raw cassava starch-degrading enzyme (RCSDE) activity of 20 U/ml was achieved when GXU20 was cultivated under optimized conditions using wheat bran (3.0% w/v) and soybean meal (2.5% w/v) as carbon and nitrogen sources at pH 5.0 and 28 °C. This represented about a sixfold increment as compared with the activity obtained under basal conditions. Starch hydrolysis degree of 95% of raw cassava flour (150 g/l) was achieved after 72 h of digestion by crude RCSDE (30 U/g flour). Ethanol yield reached 53.3 g/l with fermentation efficiency of 92% after 48 h of simultaneous saccharification and fermentation of raw cassava flour at 150 g/l using the RCSDE (30 U/g flour), carried out at pH 4.0 and 40 °C. This strain and its RCSDE have potential applications in processing of raw cassava starch to ethanol.
-
Glucose from a cellulose-containing raw material
Energy Technology Data Exchange (ETDEWEB)
Feniksova, R V
1977-01-01
Glucose was produced by mixing the raw material with an enzyme and water, enzymic hydrolysis of raw material, and separation of the hydrolyzate. To increase the yield of glucose, the hydrolysis took place in 2 stages: at the 1st stage, the hydrolysis was continued until the mixture of glucose and oligosaccharides was obtained under the influence of an active enzyme (1 to 20 units/g of cellulose present in the raw material); at the 2nd stage, cellulase immobilized on an insoluble carrier (by covalent bonds) was used for the hydrolysis of oligosaccharides. The hydromodulus of the suspension of cellulose-containing raw material was maintained 5 to 30. A carrier nonhydrolyzable by cellulase, for instance a homogenious macroporous Aerosil gel, a porous glass, or porous ceramics, was used.
-
Biological and physiological changes in raw and radiation-processed legumes
International Nuclear Information System (INIS)
El Wakeil, F.A.; Sharabash, M.T.M.; Farag, M. Diaa El-Din H.; Mahrous, S.R.
1994-01-01
Body weight of rats fed on raw kidney beans, soybeans, broad beans, chick peas and lupines suffered from poor growth due to some antinutritional factors. When the studied legumes were exposed to 10 kGy, the rats gained more weight than those kept on raw legumes. When extracts of raw legumes were intraperitoneally injected, the LD 50 were found to be 125, 300 and 1800 mg/kg, for raw kidney beans, raw soybeans, and raw broad beans respectively. However, injecting extracts of raw chick peas and raw lupines did not kill the rats even at higher concentration levels of 3000 mg/kg. Similar results were obtained with irradiated chick peas and lupines (10 kGy). Meanwhile, after irradiation treatment of kidney beans, soybeans and broad beans, the LD 50 were found to be 250, 400 and 2000 mg/kg for the above pulses respectively. Both raw and irradiated kidney beans and raw soybeans were most active in stimulating pancreas and liver growth and reducing spleen weight. Irradiated soybeans showed a moderate but significant increase in liver weight only. However, rats fed on both raw and irradiated broad beans, chick peas and lupines in their diets did not suffer any pancreatic and liver hypertrophy or spleen atrophy. The haematological parameters investigated showed that there was no significant differences between rat groups fed on either raw or irradiated legumes. It could be concluded that irradiation offers a good treatment for legumes as it has a beneficial effect to correct the poor growth for rats fed on raw beans during experimental period without any deleterious physiological effects. (author)
-
Strategic raw materials. Risk management; Strategische Rohstoffe. Risikovorsorge
Energy Technology Data Exchange (ETDEWEB)
Bertau, Martin [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Technische Chemie; Gutzmer, Jens [Helmholtz-Institut fuer Ressourcentechnologie Freiberg (Germany); Matschullat, Joerg (ed.) [Technische Univ. Bergakademie Freiberg (Germany). Interdisziplinaeres Oekologisches Zentrum (IOeZ); Kausch, Peter
2014-07-01
This volume is divided into four chapters: (1) Raw material management, (2) Primary raw materials, (3) Secondary raw materials and recycling, (4). Processing and products. The topics for the chapter ''Raw material management'' are: Substitution of raw materials - framework conditions and implementation; Thales: Strategic raw materials; Time for cooperation between the EU and China in raw materials policy; Availability of elements for the semiconductor industry; Market price risks of raw material-intensive companies - identification and management. The topics on the second item ''Primary raw materials'' are: The supply of economic-critical raw materials - A search and analysis for causes; Lithium extraction from primary raw materials - state and perspectives; The global market of rare earths - A balancing act; Rare earth deposits in Namibia; New technologies in exploration and discovery - Focus on activities in Europe. The third chapter, ''Secondary Raw Materials and Recycling'', covered the topics: Technology metals - Systemic Requirements along the recycling chain; Integrated re-use of high-tech and greentech wastes; From the sewage sludge ash to the phosphorus fertilizer RecoPhos P38 in the stress field of waste, fertilizer and soil protection. In chapter 4. ''Processing and products'' are the topics: Treatment and processing of rare earth metals; Processing of mineral resources - opportunities and challenges; Consequences of modern germanium chemistry; Strategic resources - Risk management. A review and outlook with a pinch of fantasy.. [German] Dieser Band gliedert sich in vier Kapitel: (1) Rohstoffwirtschaft, (2) Primaere Rohstoffe, (3) Sekundaere Rohstoffe und Recycling,(4). Verarbeitung und Produkte. Die Themen zum Kapitel ''Rohstoffwirtschaft'' sind: Substitution von Rohstoffen - Rahmenbedingungen und Umsetzung; Thales: Strategische Rohstoffe; Zeit fuer
-
Treatment and conditioning of solid and liquid raw
International Nuclear Information System (INIS)
Jakubec, R.
2015-01-01
Jadrova a vyradovacia spolocnost, a.s. (JAVYS) implements activities within the processes of treatment and conditioning of radioactive waste (RAW) at two nuclear facilities, one of them located in Bohunice - Technologies for treatment and conditioning of RAW. This nuclear facility includes: Bohunice RAW treatment centre, bituminization lines, waste water purification station and technologies for sorting, fragmentation and decontamination of metallic RAW. The Bohunice RAW treatment centre (BRTC) in Bohunice processes and conditions liquid and solid radioactive waste produced during the A1 NPP and V1 NPP decommissioning, waste from the operation of V2 NPP in Bohunice as well as from the operation of NPP EMO 1,2 in Mochovce. The BRTC includes the following technological facilities: sorting, high-pressure compaction, incineration, concentration and cementation. Treatment of radioactive wastes in the BRTC is described. (authors)
-
Investigation on pyrolysis of some organic raw materials
Directory of Open Access Journals (Sweden)
Purevsuren B
2017-02-01
Full Text Available We have been working on pyrolysis of some organic raw materials including different rank coals, oil shale, wood waste, animal bone, cedar shell, polypropylene waste, milk casein and characterization of obtained hard residue, tar and pyrolytic water and gas after pyrolysis. The technical characteristics of these organic raw materials have been determined and the thermal stability characteristics such as thermal stability indices (T5% and T25% determined by using thermogravimetric analysis. The pyrolysis experiments were performed at different heating temperatures and the yields of hard residue, tar, pyrolysis water and gaseous products were determined and discussed. The main technical characteristics of hard residue of organic raw materials after pyrolysis have been determined and the adsorption ability of pyrolysis hard residue and its activated carbon of organic raw materials also determined. The pyrolysis tars of organic raw materials were distilled in air condition and determined the yields of obtained light, middle and heavy fractions and bitumen like residue with different boiling temperature. This is the first time to investigate the curing ability of pyrolysis tars of organic raw materials for epoxy resin and the results of these experiments showed that only tar of milk casein has the highest (95.0%, tar of animal bone has certain (18.70% and tars of all other organic raw materials have no curing ability for epoxy resin.
-
OZONE ABSORPTION IN RAW WATERS
Directory of Open Access Journals (Sweden)
LJILJANA TAKIĆ
2008-03-01
Full Text Available The ozone absorption in raw water entering the main ozonization step at the Belgrade drinking water supply plant was investigated in a continuous stirred tank reactor (CSTR. A slow chemical reaction rate of dissolved ozone and pollutants present in raw water have been experimentally determined. The modified Hatta number was defined and calculated as a criterion which determines whether and to which extent the reactions of ozone and pollutants influence the rate of the pure physical ozone absorption.
-
Benefits of balancing method for component RAW importance measure
International Nuclear Information System (INIS)
Kim, Kil Yoo; Yang, Joon Eon
2005-01-01
In the Risk Informed Regulation and Applications (RIR and A), the determination of risk significant Structure, System and Components (SSCs) plays an important role, and importance measures such as Fussell-Vesely (FV) and RAW (Risk Achievement Worth) are widely used in the determination of risk significant SSCs. For example, in the Maintenance Rule, Graded Quality Assurance(GQA) and Option 2, FV and RAW are used in the categorization of SSCs. Especially, in the GQA and Option 2, the number of SSCs to be categorized is too many to handle, so the FVs and RAWs of the components are practically derived in a convenient way with those of the basic events which have already been acquired as PSA (Probabilistic Safety Assessment) results instead of by reevaluating the fault tree/event tree of the PSA model. That is, the group FVs and RAWs for the components are derived from the FVs and RAWs of the basic events which consist of the group. Here, the basic events include random failure, Common Cause Failure (CCF), test and maintenance, etc. which make the system unavailable. A method called 'Balancing Method' which can practically and correctly derive the component RAW with the basic event FVs and RAWs even if CCFs exists as basic events was introduced in Ref.. However, 'Balancing Method' has other advantage, i.e., it can also fairly correctly derive component RAW using fault tree without using basic events FVs and RAWs
-
Characterization of Limestone as Raw Material to Hydrated Lime
Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd
2018-03-01
In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.
-
Ethanol is a strategic raw material
Directory of Open Access Journals (Sweden)
Baras Josip K.
2002-01-01
Full Text Available The first part of this review article considers general data about ethanol as an industrial product, its qualities and uses. It is emphasized that, if produced from biomass as a renewable raw material, its perspectives as a chemical raw material and energent are brilliant. Starchy grains, such as corn, must be used as the main raw materials for ethanol production. The production of bioethanol by the enzyme-catalyzed conversion of starch followed by (yeast fermentation, distillation is the process of choice. If used as a motor fuel, anhydrous ethanol can be directly blended with gasoline or converted into an oxygenator such as ETBE. Finally, bioethanol production in Yugoslavia and the possibilities for its further development are discussed.
-
VERAM - Vision and Roadmap for European Raw Materials
Baumgarten, Wibke; Vashev, Boris
2017-04-01
The overall objective of VERAM project is to produce a Vision and Roadmap for European Raw Materials in 2050 based on raw materials research and innovation (R&I) coordination. Two leading European Technology Platforms (ETPs): ETP SMR (Sustainable Minerals Resources) and FTP (Forest Technology Platform) are joining forces to develop a common vison and roadmap with the support of ECTP (European Construction Technology Platform), represented by UNIVPM, SusChem (ETP for Sustainable Chemistry), represented by Cefic, EuMaT (Advanced Materials ETP), represented by VITO, ERAMIN 2, represented by Research Centre JUELICH and WoodWisdom Network Plus represented by the Agency for Renewable Resources (FNR). This partnership provides VERAM with expertise from downstream applications and additional knowledge on non-biotic and biotic raw materials. The project encourages capacity building as well as transfer of knowledge. It expects to provide an innovation reference point for the European Institute of Innovation & Technology (EIT) Raw Materials (formerly the KIC Raw MatTERS), to coordinate the network involved in the European Innovation Partnership (EIP) on Raw Materials Commitments and relevant proposals funded under Horizon 2020. It provides a platform for identifying gaps and complementarities and enables their bridging. VERAM will be able to advise the European Commission and Member States on future research needs and policies to stimulate innovation and assist in overcoming fragmentation in the implementing the EIP Raw Materials Strategic Implementation Plan. VERAM looks for mutually beneficial information exchange, encourages cross-fertilization between actions undertaken by different raw material industries, and expects to accelerate exploitation of breakthrough innovations. One of the main outcomes of the project is the presentation of a common long term 2050 Vision and Roadmap for relevant raw materials including metals, industrial minerals and aggregates and wood. The
-
Directory of Open Access Journals (Sweden)
Jivan Singh
2011-05-01
Full Text Available The present paper aims to investigate the physical characteristics of sawdust relative to its use as an adsorbent for removal of an acid dye (Orange G from aqueous solutions. The raw sawdust was sieved to have a uniform size and was activated by sulphuric acid by refluxing the content at 60 oC for 4 h. Surface morphology and surface functional groups of both raw and modified sawdust samples were investigated by Scanning Electron Microscope (SEM, Energy Dispersive X-ray Analysis (EDX, Fourier Transformation Infrared (FTIR, and elemental analysis. All these analyses displayed significant change in the structure of the sawdust. The data obtained from batch adsorption experiments for the removal of the selected dye confirmed that adsorption characteristics of the modified sawdust were better than those of raw sawdust.
-
Murphy, Steven C; Martin, Nicole H; Barbano, David M; Wiedmann, Martin
2016-12-01
This article provides an overview of the influence of raw milk quality on the quality of processed dairy products and offers a perspective on the merits of investing in quality. Dairy farmers are frequently offered monetary premium incentives to provide high-quality milk to processors. These incentives are most often based on raw milk somatic cell and bacteria count levels well below the regulatory public health-based limits. Justification for these incentive payments can be based on improved processed product quality and manufacturing efficiencies that provide the processor with a return on their investment for high-quality raw milk. In some cases, this return on investment is difficult to measure. Raw milks with high levels of somatic cells and bacteria are associated with increased enzyme activity that can result in product defects. Use of raw milk with somatic cell counts >100,000cells/mL has been shown to reduce cheese yields, and higher levels, generally >400,000 cells/mL, have been associated with textural and flavor defects in cheese and other products. Although most research indicates that fairly high total bacteria counts (>1,000,000 cfu/mL) in raw milk are needed to cause defects in most processed dairy products, receiving high-quality milk from the farm allows some flexibility for handling raw milk, which can increase efficiencies and reduce the risk of raw milk reaching bacterial levels of concern. Monitoring total bacterial numbers in regard to raw milk quality is imperative, but determining levels of specific types of bacteria present has gained increasing importance. For example, spores of certain spore-forming bacteria present in raw milk at very low levels (e.g., products to levels that result in defects. With the exception of meeting product specifications often required for milk powders, testing for specific spore-forming groups is currently not used in quality incentive programs in the United States but is used in other countries (e.g., the
-
Centers for Disease Control (CDC) Podcasts
2013-08-05
Dr. Duc Vugia, chief of the Infectious Diseases Branch at the California Department of Public Health, discusses the dangers of eating raw oysters. Created: 8/5/2013 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID). Date Released: 8/7/2013.
-
Characterization of raw materials and manufactured binderless particleboard from oil palm biomass
International Nuclear Information System (INIS)
Hashim, Rokiah; Nadhari, Wan Noor Aidawati Wan; Sulaiman, Othman; Kawamura, Fumio; Hiziroglu, Salim; Sato, Masatoshi; Sugimoto, Tomoko; Seng, Tay Guan; Tanaka, Ryohei
2011-01-01
The objective of this study was to examine the extractive, holocellulose, alpha cellulose, lignin, starch, and sugar contents of oil palm biomass and to evaluate its suitability in binderless particleboard production. In this study, bark, leaves, fronds, mid-parts and core-parts of the trunks were used to produce experimental binderless particleboard panels. Binderless particleboard panels were made with a target density of 0.80 g/cm 3 at a temperature of 180 o C and a pressure of 12 MPa in a computer controlled hot press. The modulus of rupture, the internal bond strength, the thickness swelling and the water absorption of the panels were evaluated. Fourier transform infrared spectroscopy and field emission scanning electron microscopy were used to characterize the properties of the raw materials and the manufactured panels. The chemical composition of the oil palm biomass consisted of high holocellulose, lignin, starch and sugar contents that have been found to aid in the production of binderless particleboard. The core-part of the trunk contained the highest amount of starch and total sugar. Samples made from the core-parts and fronds had sufficient modulus of rupture and internal bond strength to meet the Japanese Industrial Standard. The internal bond strength of the mid-part panels also met the standard. However, binderless board prepared from bark and leaves showed poor modulus of rupture and internal bond strength. Samples from the core-parts had the lowest thickness swell and water absorption but did not meet the above standard. The Fourier transform infrared spectroscopy spectra did not show any substantial difference between the raw materials and the manufactured panels. Field emission scanning electron microscopy indicated that the compressed cells varied between raw material types and showed the presence of compressed cells with some starch granules that facilitated adhesion. Based on the findings of this study, oil palm has the potential to be used to
-
Caffeine Extraction from Raw and Roasted Coffee Beans.
Chiang, Donyau; Lin, Chih-Yang; Hu, Chen-Ti; Lee, Sanboh
2018-04-01
Coffee is a stimulant, psychoactive, popular daily beverage, and its caffeine affects human physiological health and behavior. These important issues prompted us to study caffeine extraction from both the raw and roasted coffee beans of 3 types at different temperatures. A hemispheric model is developed to simulate the extraction process of the caffeine from the coffee beans of hemisphere is proposed. The experimental data are in good agreement with the predicted model. The effective diffusivities of caffeine in both the raw and roasted beans increase with temperature in all 3 types. An incubation period, decreasing with increasing temperature, is observed in all samples studied. Caffeine extraction in roasted beans is more rapid than that for the raw beans and the time difference is significant at low temperatures. In both the raw and roasted samples, caffeine diffusion in the raw beans and the incubation behavior are thermally activated processes. Single activation energies are obtained for diffusion within the extraction temperature range for all beans tested with the exception of one type of the coffee beans, Mandheling, which exhibits 2 activation energies in raw samples. The surface energies of the epidermis of the raw beans and roasted beans obtained from the contact angle measurements are used to interpret the difference of incubation periods. This study has a potential application to the decaffeinated coffee industry.Caffeine affects human physiological health and behavior so that caffeine extraction from coffee beans of different types at different temperatures is important for product refining and customers. © 2018 Institute of Food Technologists®.
-
19 CFR 151.22 - Estimated duties on raw sugar.
2010-04-01
... 19 Customs Duties 2 2010-04-01 2010-04-01 false Estimated duties on raw sugar. 151.22 Section 151... THE TREASURY (CONTINUED) EXAMINATION, SAMPLING, AND TESTING OF MERCHANDISE Sugars, Sirups, and Molasses § 151.22 Estimated duties on raw sugar. Estimated duties shall be taken on raw sugar, as defined...
-
Modeling to control spores in raw milk
Vissers, M.
2007-01-01
A modeling approach was used to identify measures at the farm that reduce transmission of microorganisms to raw milk. Butyric acid bacteria (BAB) and Bacillus cereus were used as case-studies. Minimizing the concentration of BAB spores in raw milk is important to prevent late-blowing of Gouda-type
-
A balancing method for calculating a component raw involving CGF
Energy Technology Data Exchange (ETDEWEB)
Kim, K.; Kang, D.; Yang, J.E. [Integrated Safety Assessment Division, Korea Atomic Energy Research Institute, Daejon (Korea, Republic of)
2004-07-01
In this paper, a method called the 'Balancing Method' to derive a component RAW (Risk Achievement Worth) with basic event RAWs including a CCF (Common Cause Failure) RAW is summarized, and compared with the method proposed by the NEI (Nuclear Energy Institute) by mathematically checking the background on which the two methods are based. It is proved that the Balancing Method has a strong mathematically background. While the NEI method significantly underestimates the component RAW and is a little bit ad hoc in handling CCF RAW, the Balancing Method estimates the true component RAW very closely. Validity of the Balancing Method is based on the fact that if an component is out-of-service, it does not mean that the component is non-existent, but integrates the possibility that the component might fail due to CCF. The validity of the Balancing Method is proved by comparing it to the exact component RAW generated from the fault tree model.
-
A balancing method for calculating a component raw involving CGF
International Nuclear Information System (INIS)
Kim, K.; Kang, D.; Yang, J.E.
2004-01-01
In this paper, a method called the 'Balancing Method' to derive a component RAW (Risk Achievement Worth) with basic event RAWs including a CCF (Common Cause Failure) RAW is summarized, and compared with the method proposed by the NEI (Nuclear Energy Institute) by mathematically checking the background on which the two methods are based. It is proved that the Balancing Method has a strong mathematically background. While the NEI method significantly underestimates the component RAW and is a little bit ad hoc in handling CCF RAW, the Balancing Method estimates the true component RAW very closely. Validity of the Balancing Method is based on the fact that if an component is out-of-service, it does not mean that the component is non-existent, but integrates the possibility that the component might fail due to CCF. The validity of the Balancing Method is proved by comparing it to the exact component RAW generated from the fault tree model
-
Raw milk consumption and health
Directory of Open Access Journals (Sweden)
Popović-Vranješ Anka
2015-01-01
Full Text Available Contrary to the safe practices of milk pasteurization or sterilization, which effectively reduce foodborne outbreaks incidence associated with raw milk and dairy products use, outbreaks caused by such products continue to occur. Despite this fact, a worldwide movement advocating for the rights of raw milk and cheese selling and consumption, due to their specific nutritive characteristics, has strengthened significantly in recent years. Traditional agricultural manufacturers from Serbia still sell products related to thermally unprocessed milk, such as cottage cheese and raw cream. In AP Vojvodina during the period of 1981-2010 a total of 179 foodborne outbreaks were reported, where the incriminated cause of the outbreak were milk or diary. In 126 (70.39% outbreaks, totaling 2276 sick individuals and one casualty, it was confirmed that the incriminated food was from the group of dairy products. In 48 instances (26.82%, bacteriological tests confirmed that milk and dairy products were excluded as the outbreak causes, while in another 5 (2.79% outbreaks, microbiological analysis of food failed to confirm any relation to the actual epidemiological instances. In some cases, bacteriological testing of incriminated foods was not possible. In the cases of outbreaks associated with the consumption of milk and dairy products, traditional raw milk products were cited as being used. Consumption of unpasteurized milk and cheese represents public health threat. National and international rules ensuring use of safe products for human consumption have to set rules of trade of thermally processed milk and products on the market. [Projekat Ministarstva nauke Republike Srbije, br. TR31095
-
Islam, Mohammad A; Mondol, Abdus S; Azmi, Ishrat J; de Boer, Enne; Beumer, Rijkelt R; Zwietering, Marcel H; Heuvelink, Annet E; Talukder, Kaisar A
2010-11-01
The major objective of this study was to investigate the prevalence of Shiga toxin (Stx)-producing Escherichia coli (STEC) in different types of food samples and to compare their genetic relatedness with STEC strains previously isolated from animal sources in Bangladesh. We investigated a total of 213 food samples, including 90 raw meat samples collected from retail butcher shops, 20 raw milk samples from domestic cattle, and 103 fresh juice samples from street vendors in Dhaka city. We found that more than 68% (n = 62) of the raw meat samples were positive for the stx gene(s); 34% (n = 21) of buffalo meats and 66% (n = 41) of beef. Approximately 10% (n = 2) of the raw milk and 8% (n = 8) of the fresh juice samples were positive for stx. We isolated STEC O157 from seven meat samples (7.8%), of which two were from buffalo meats and five from beef; and no other STEC serotypes could be isolated. We could not isolate STEC from any of the stx-positive raw milk and juice samples. The STEC O157 isolates from raw meats were positive for the stx(2), eae, katP, etpD, and enterohemorrhagic E. coli hly virulence genes, and they belonged to three different phage types: 8 (14.3%), 31 (42.8%), and 32 (42.8%). Pulsed-field gel electrophoresis (PFGE) typing revealed six distinct patterns among seven isolates of STEC O157, suggesting a heterogeneous clonal diversity. Of the six PFGE patterns, one was identical and the other two were ≥90% related to PFGE patterns of STEC O157 strains previously isolated from animal feces, indicating that raw meats are readily contaminated with fecal materials. This study represents the first survey of STEC in the food chain in Bangladesh.
-
Factors affecting adherence to a raw vegan diet.
Link, Lilli B; Jacobson, Judith S
2008-02-01
The purpose of this study was to evaluate adherence and identify predictors of adherence to a raw vegan diet (i.e., uncooked plant foods) following a stay at a raw vegan institute. In this cohort study of guests at a raw vegan institute, subjects completed written questionnaires upon arrival and 12 weeks later. Of 107 eligible guests, 84 participated. Mean age was 54 years, 23 were male, and 73 white. Fifty-one completed the 12-week follow-up. Eight (16%) reported their diet to be 80% raw vegan at baseline and 14 (28%) at follow-up. Based on a raw vegan dietary adherence score (range 0-42) created for this study, mean adherence (SD) increased from 15.1 (5.4) to 17.0 (5.8) over 12 weeks (p=0.03). Baseline predictors of adherence included: education (beta=0.95), severity of disease (beta=0.98), and self-efficacy to adhere (beta=0.72). Future interventions that evaluate this diet should address self-efficacy, an important, potentially remediable predictor of adherence.
-
Factors affecting adherence to a raw vegan diet
Link, Lilli B.; Jacobson, Judith S.
2008-01-01
The purpose of this study was to evaluate adherence and identify predictors of adherence to a raw vegan diet (i.e., uncooked plant foods) following a stay at a raw vegan institute. In this cohort study of guests at a raw vegan institute, subjects completed written questionnaires upon arrival and 12 weeks later. Of 107 eligible guests, 84 participated. Mean age was 54 years, 23 were male, and 73 white. Fifty-one completed the 12-week follow-up. Eight (16%) reported their diet to be ≥80% raw vegan at baseline and 14 (28%) at follow-up. Based on a raw vegan dietary adherence score (range 0-42) created for this study, mean adherence (SD) increased from 15.1 (5.4) to 17.0 (5.8) over 12 weeks (p=0.03). Baseline predictors of adherence included: education (β=0.95), severity of disease (β=0.98), and self-efficacy to adhere (β=0.72). Future interventions that evaluate this diet should address self-efficacy, an important, potentially remediable predictor of adherence. PMID:18243943
-
Origins of effective resistivity in collisionless magnetic reconnection
Energy Technology Data Exchange (ETDEWEB)
Singh, Nagendra [Electrical and Computer Engineering, University of Alabama, Huntsville, Alabama 35899 (United States)
2014-07-15
The mechanisms that provide effective resistivity for supporting collisonless magnetic reconnection have remained unsettled despite numerous studies. Some of these studies demonstrated that the electron pressure nongyrotropy generates the resistivity (η{sub npg}) in the electron diffusion region (EDR). We derive an analytical relation for the effective resistivity (η{sub kin}) by momentum balance in a control volume in the EDR. Both η{sub npg} and η{sub kin} mutually compare well and they also compare well with the resistivity required to support reconnection electric field E{sub rec} in multi-dimensional particle-in-cell simulations as well as in satellite observations when reconnection occurs in an EDR. But they are about an order of magnitude or so smaller than that required when the reconnection occurred in a much wider reconnecting current sheet (RCS) of half width (w) of the order of the ion skin depth (d{sub i}), observed in the Earth magnetosphere. The chaos-induced resistivity reported in the literature is found to be even more deficient. We find that for reconnection in RCS with w ∼ d{sub i}, anomalous diffusion, such as the universal Bhom diffusion and/or that arising from kinetic Alfven waves, could fairly well account for the required resistivity.
-
An electronics laboratory in Ceylon
International Nuclear Information System (INIS)
1962-01-01
At the request of the Ceylon Government, the International Atomic Energy Agency provided Ceylon with the services of an expert to install electronic equipment for nuclear raw materials prospecting and assay and to train local personnel in the operation and maintenance of the instruments
-
The raw, takes off a weight of above
International Nuclear Information System (INIS)
Carta Petrolera
1998-01-01
With the technology of the deasphalted in Colombia, advance investigations that allow improving the quality of heavy raw. A new possibility opens up to market that type of petroleum. The Colombian Institute of the Petroleum developed a simple and more economic technology for deasphalted the heavy raw, using temperatures and moderate pressures. It is a deasphalted process to convert the raw weighed in light, facilitating their transport and improving their quality, using the traditional method, using commercial solvents but with different proportions, optimizing the relationship cost / benefit
-
PERSPECTIVE NONMETALLIC RAW MATERIALS AND THEIR UTILIZATION
Directory of Open Access Journals (Sweden)
Havelka Jaroslav
1997-10-01
Full Text Available It is the existence of the domestic base of raw materials and stable or growing markets that are a precondition for the prospectiveness industrial minerals. Traditional and non-traditional prospective nonmetal-liferous raw materials can be distinguished. The main trends in new industrial applications of industrial minerals are being stated. In the Czech Republic, the following may be ranked among the traditional prospective nonme-talliferous raw materials: kaoline, refractory clays, ceramic and expandable clays, glass and foundry sands, li-mestones, building stones, gypsum, cast basalt, bentonite, diatomite, feldspars, graphite. Alkali rocks, industrial garnets, flaky mica, wollastonite and yet unmined staurolite, minerals of the sillimanite group and others belong to the non-traditional prospective industrial minerals.
-
Raw material ‘criticality’—sense or nonsense?
International Nuclear Information System (INIS)
Frenzel, M; Kullik, J; Reuter, M A; Gutzmer, J
2017-01-01
The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead. (topical review)
-
Raw material ‘criticality’—sense or nonsense?
Frenzel, M.; Kullik, J.; Reuter, M. A.; Gutzmer, J.
2017-03-01
The past decade has seen a resurgence of interest in the supply security of mineral raw materials. A key to the current debate is the concept of ‘criticality’. The present article reviews the criticality concept, as well as the methodologies used in its assessment, including a critical evaluation of their validity in view of classical risk theory. Furthermore, it discusses a number of risks present in global raw materials markets that are not captured by most criticality assessments. Proposed measures for the alleviation of these risks are also presented. We find that current assessments of raw material criticality are fundamentally flawed in several ways. This is mostly due to a lack of adherence to risk theory, and highly limits their applicability. Many of the raw materials generally identified as critical are probably not critical. Still, the flaws of current assessments do not mean that the general issue of supply security can simply be ignored. Rather, it implies that new assessments are required. While the basic theoretical framework for such assessments is outlined in this review, detailed method development will require a major collaborative effort between different disciplines along the raw materials value chain. In the opinion of the authors, the greatest longer-term challenge in the raw materials sector is to stop, or counteract the effects of, the escalation of unit energy costs of production. This issue is particularly pressing due to its close link with the renewable energy transition, requiring more metal and mineral raw materials per unit energy produced. The solution to this problem will require coordinated policy action, as well as the collaboration of scientists from many different fields—with physics, as well as the materials and earth sciences in the lead.
-
International Nuclear Information System (INIS)
Migdal, W.; Owczarczyk, H.B.; Malec-Czechowska, K.
1997-01-01
The results of investigations the electron beam irradiation on the microbial contamination of selected new generation cosmetics and raw products used in cosmetic industry are reported. The radiation doses applied were not higher than 6.0 kGy. The levels of microbial contamination were determined in irradiated and non-irradiated samples by standard methods routinely used. The results obtained show that radiation can be successfully used for decontamination of cosmetics and some of their raw materials, without changing the quality and applicability of the product. (author)
-
Removal of aniline and phenol from water using raw and aluminum hydroxide-modified diatomite.
Wu, C D; Zhang, J Y; Wang, L; He, M H
2013-01-01
The feasibility of using raw diatomite and aluminum hydroxide-modified diatomite (Al-diatomite) for removal of aniline and phenol from water was investigated. Their physicochemical characteristics such as pHsolution, point of zero charge (pHPZC), surface area, Fourier transform infrared (FT-IR) and scanning electron microscopy was determined. After the raw diatomite was modified, the surface area of Al-diatomite increases from 26.67 to 82.65 m(2) g(-1). The pHPZC and pHsolution (10%) occurred around pH 5.2 and pH 8.6, respectively. The removal rates of aniline and phenol on diatomite and Al-diatomite decreased with increasing solution pH, while surface charge density decreased. The adsorption of aniline and phenol on diatomite presented a good fit to the Langmuir and Freundlich models, but the models are not fit to forecast the adsorption of aniline and phenol on Al-diatomite. The study indicated that electrostatic interaction was a dominating mechanism of aniline and phenol sorption onto Al-diatomite.
-
Hygienic quality of raw milk with regard to legislation
Directory of Open Access Journals (Sweden)
Slavko Kirin
2001-01-01
Full Text Available Hygienic quality of raw milk is basic indicator of hygienic conditionduring processing and handling of milk as well as economical valorisation of animal product as a raw material in dairy products manufacture. Thus, total bacterial count in 1 mL of raw milk is used in modern legislation in milk pricing system. Apart from the economical and technological reasons hygienic quality of raw milk is also important from the health safety issue. In this paper microbiological quality legislation, set down by the EU and Croatian directives, are presented. Apart form the total microorganisms number the normative on the somatic cell number in row milk, as one of the quality indicators, are also presented. Pricing system of raw milk with regard to hygienic quality, current legislation especially from the point of view of a new legislation on row milk quality as well as suggestions to faster association into progressive dairy, legislation are listed.
-
EARLINET Single Calculus Chain - technical - Part 1: Pre-processing of raw lidar data
D'Amico, Giuseppe; Amodeo, Aldo; Mattis, Ina; Freudenthaler, Volker; Pappalardo, Gelsomina
2016-02-01
In this paper we describe an automatic tool for the pre-processing of aerosol lidar data called ELPP (EARLINET Lidar Pre-Processor). It is one of two calculus modules of the EARLINET Single Calculus Chain (SCC), the automatic tool for the analysis of EARLINET data. ELPP is an open source module that executes instrumental corrections and data handling of the raw lidar signals, making the lidar data ready to be processed by the optical retrieval algorithms. According to the specific lidar configuration, ELPP automatically performs dead-time correction, atmospheric and electronic background subtraction, gluing of lidar signals, and trigger-delay correction. Moreover, the signal-to-noise ratio of the pre-processed signals can be improved by means of configurable time integration of the raw signals and/or spatial smoothing. ELPP delivers the statistical uncertainties of the final products by means of error propagation or Monte Carlo simulations. During the development of ELPP, particular attention has been payed to make the tool flexible enough to handle all lidar configurations currently used within the EARLINET community. Moreover, it has been designed in a modular way to allow an easy extension to lidar configurations not yet implemented. The primary goal of ELPP is to enable the application of quality-assured procedures in the lidar data analysis starting from the raw lidar data. This provides the added value of full traceability of each delivered lidar product. Several tests have been performed to check the proper functioning of ELPP. The whole SCC has been tested with the same synthetic data sets, which were used for the EARLINET algorithm inter-comparison exercise. ELPP has been successfully employed for the automatic near-real-time pre-processing of the raw lidar data measured during several EARLINET inter-comparison campaigns as well as during intense field campaigns.
-
Rheological behavior of raw natural rubber coagulated by microorganisms
Directory of Open Access Journals (Sweden)
Zhifen Wang
2014-01-01
Full Text Available Tests of the strain sweep, frequency sweep and stress relaxation for raw natural rubber coagulated by microorganisms (NR-m and raw natural rubber coagulated by acid (NR-a were carried out with the use of a rubber process analyzer (RPA. The results showed that the storage torque, complex viscosity of NR-m were higher than those of NR-a while the loss factor was lower. The effect of temperature on viscosity of raw NR was studied following the Arrhenious-Frenkel-Eyring model. The viscous flow behavior of NR-m was poorer than those of NR-a. Furthermore, stress relaxation measurements of raw NR showed a longer period of relaxation for NR-m.
-
Phytochemical and Nutritional Evaluation of Raw and Fermented ...
African Journals Online (AJOL)
Raw Alchornea seed meal contains phytic acids, tannins, saponins, cardiac glycosides, steroids, flavnoids, alkaloids and anthraquinone. Fermenting the seed meal caused 56.2% reduction in the phytic acid content and totally eliminated its anthraquinone content. With 10% raw Alchornea seed meal, broilers grew ...
-
Supply optimization for the production of raw sugar
DEFF Research Database (Denmark)
Grunow, Martin; Günther, H.O.; Westinner, R.
2007-01-01
Based on a case study from Venezuela, the production of raw sugar is investigated. Ideally, sugar mills operate at a constant production rate. However, safety stocks of the raw material cannot be maintained as sugar cane quality deteriorates very rapidly. Sugar cane is therefore continuously...
-
Effect Of Dietary Raw, Cooked And Toasted Mucuna Pruriens Seeds ...
African Journals Online (AJOL)
A 5-week feeding trial was conducted to determine the effect or dietary raw, cooked and toasted Mucuna pruriens seeds (velvet bean) on the performance of finisher broilers. Raw Mucuna pruriens seeds contained 30.3% crude protein. At 10% dietary level, raw and toasted Mucuna pruriens seed meals significantly (P ...
-
Pellet production from agricultural raw materials - A systems study
Energy Technology Data Exchange (ETDEWEB)
Nilsson, Daniel; Bernesson, Sven; Hansson, Per-Anders [Department of Energy and Technology, Swedish University of Agricultural Sciences, P.O. Box 7032, SE-75007 Uppsala (Sweden)
2011-01-15
The demand for biofuel pellets has increased considerably in recent years, causing shortage of the traditional raw materials sawdust and wood shavings. In this study, the costs and energy requirements for the production of pellets from agricultural raw materials were analysed. The materials studied were Salix, reed canary grass, hemp, straw, screenings, rape-seed meal, rape cake and distiller's waste. Four production scales were analysed, having an annual output of 80,000, 8000, 800 and 80 tonnes of pellets per year. It was concluded that the raw materials of greatest interest were Salix and reed canary grass. They had competitive raw material costs and acceptable fuel properties and could be mixed with sawdust in existing large-scale pelleting factories. Straw had low production costs but can cause serious ash-related problems and should, as also is the case for screenings, be avoided in small-scale burners. Hemp had high raw material costs and is of less commercial interest, while distiller's waste, rape-seed meal and rape cake had higher alternative values when used as protein feed. The scale of production had a crucial influence on production costs. The machinery was used much more efficiently in large-scale plants, resulting in clear cost savings. Small-scale pelleting, both static and mobile, required cheap raw materials, low labour costs and long utilisation times to be profitable. In most cases, briquetting would be more commercially viable. The energy use in manufacturing pellets from air-dried crops was generally no higher than when moist sawdust was used as the raw material. (author)
-
Preoperational test report, raw water system
Energy Technology Data Exchange (ETDEWEB)
Clifton, F.T.
1997-10-29
This represents the preoperational test report for the Raw Water System, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The system supplies makeup water to the W-030 recirculation evaporative cooling towers for tanks AY1O1, AY102, AZ1O1, AZ102. The Raw Water pipe riser and associated strainer and valving is located in the W-030 diesel generator building. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System.
-
Preoperational test report, raw water system
International Nuclear Information System (INIS)
Clifton, F.T.
1997-01-01
This represents the preoperational test report for the Raw Water System, Project W-030. Project W-030 provides a ventilation upgrade for the four Aging Waste Facility tanks. The system supplies makeup water to the W-030 recirculation evaporative cooling towers for tanks AY1O1, AY102, AZ1O1, AZ102. The Raw Water pipe riser and associated strainer and valving is located in the W-030 diesel generator building. The tests verify correct system operation and correct indications displayed by the central Monitor and Control System
-
Identification of Particles in Parenteral Drug Raw Materials.
Lee, Kathryn; Lankers, Markus; Valet, Oliver
2018-04-18
Particles in drug products are not good and are therefore regulated. These particles can come from the very beginning of the manufacturing process, from the raw materials. To prevent particles, it is important to understand what they are and where they come from so the raw material quality, processing, and shipping can be improved. Thus, it is important to correctly identify particles seen in raw materials. Raw materials need to be of a certain quality with respect to physical and chemical composition, and need to have no contaminants in the form of particles which could contaminate the product or indicate the raw materials are not pure enough to make a good quality product. Particles are often seen when handling raw materials due to color, size, or shape characteristics different from those in the raw materials. Particles may appear to the eye to be very different things than they actually are, so microscope, chemical, and elemental analyses are required for accuracy in proper identification. This paper shows how using three different spectroscopy tools correctly and together can be used to identify particles from extrinsic, intrinsic, and inherent particles. Sources of materials can be humans and the environment (extrinsic), from within the process (intrinsic), and part of the formulation (inherent). Microscope versions of Raman spectroscopy, laser-induced breakdown spectroscopy (LIBS), and IR spectroscopy are excellent tools for identifying particles because they are fast and accurate techniques needing minimal sample preparation that can provide chemical composition as well as images that can be used for identification. The micro analysis capabilities allow for easy analysis of different portions of samples so multiple components can be identified and sample preparation can be reduced. Using just one of these techniques may not be sufficient to give adequate identification results so that the source of contamination can be adequately identified. The
-
40 CFR 63.1347 - Standards for raw and finish mills.
2010-07-01
... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for raw and finish mills. 63... and Operating Limits § 63.1347 Standards for raw and finish mills. The owner or operator of each new or existing raw mill or finish mill at a facility which is a major source subject to the provisions...
-
Scoping Future Policy Dynamics in Raw Materials Through Scenarios Testing
Correia, Vitor; Keane, Christopher; Sturm, Flavius; Schimpf, Sven; Bodo, Balazs
2017-04-01
The International Raw Materials Observatory (INTRAW) project is working towards a sustainable future for the European Union in access to raw materials, from an availability, economical, and environmental framework. One of the major exercises for the INTRAW project is the evaluation of potential future scenarios for 2050 to frame economic, research, and environmental policy towards a sustainable raw materials supply. The INTRAW consortium developed three possible future scenarios that encompass defined regimes of political, economic, and technological norms. The first scenario, "Unlimited Trade," reflects a world in which free trade continues to dominate the global political and economic environment, with expectations of a growing demand for raw materials from widely distributed global growth. The "National Walls" scenario reflects a world where nationalism and economic protectionism begins to dominate, leading to stagnating economic growth and uneven dynamics in raw materials supply and demand. The final scenario, "Sustainability Alliance," examines the dynamics of a global political and economic climate that is focused on environmental and economic sustainability, leading towards increasingly towards a circular raw materials economy. These scenarios were reviewed, tested, and provided simulations of impacts with members of the Consortium and a panel of global experts on international raw materials issues which led to expected end conditions for 2050. Given the current uncertainty in global politics, these scenarios are informative to identifying likely opportunities and crises. The details of these simulations and expected responses to the research demand, technology investments, and economic components of raw materials system will be discussed.
-
Identification of raw as a regulator of glial development.
Directory of Open Access Journals (Sweden)
Diana Luong
Full Text Available Glial cells perform numerous functions to support neuron development and function, including axon wrapping, formation of the blood brain barrier, and enhancement of synaptic transmission. We have identified a novel gene, raw, which functions in glia of the central and peripheral nervous systems in Drosophila. Reducing Raw levels in glia results in morphological defects in the brain and ventral nerve cord, as well as defects in neuron function, as revealed by decreased locomotion in crawling assays. Examination of the number of glia along peripheral nerves reveals a reduction in glial number upon raw knockdown. The reduced number of glia along peripheral nerves occurs as a result of decreased glial proliferation. As Raw has been shown to negatively regulate Jun N-terminal kinase (JNK signaling in other developmental contexts, we examined the expression of a JNK reporter and the downstream JNK target, matrix metalloproteinase 1 (mmp1, and found that raw knockdown results in increased reporter activity and Mmp1 levels. These results are consistent with previous studies showing increased Mmp levels lead to nerve cord defects similar to those observed upon raw knockdown. In addition, knockdown of puckered, a negative feedback regulator of JNK signaling, also causes a decrease in glial number. Thus, our studies have resulted in the identification of a new regulator of gliogenesis, and demonstrate that increased JNK signaling negatively impacts glial development.
-
Chemical composition of raw and deresinated peat waxes
Energy Technology Data Exchange (ETDEWEB)
Bel' kevich, P I; Ivanova, L A; Piskunova, T A; Tserlyukevich, Ya V; Yurkevich, E A
1980-01-01
Research was conducted using absorption chromatography and spectroscopy to study the changes in the chemical composition of raw peat wax taking place in the deresination process. Characteristics of the raw, deresinated waxes and resins removed are given. The fractions obtained showed that both raw and deresinated wax contain the same basic compound classes: hydrocarbons, alcohols, complex ether and acids; but their proportions in the waxes are different. After deresination most of the dark-colored polyfunctional compounds, a portion of the soluble unsaturated hydrocarbons and alcohols, and all the sterenes transfer into the resin. This causes the light color and specific physical properties of deresinated wax. (13 refs.) (In Russian)
-
40 CFR 1065.230 - Raw exhaust flow meter.
2010-07-01
... the following cases, you may use a raw exhaust flow meter signal that does not give the actual value... dew and pressure, p total at the flow meter inlet. Use these values in emission calculations according... CONTROLS ENGINE-TESTING PROCEDURES Measurement Instruments Flow-Related Measurements § 1065.230 Raw exhaust...
-
Raw material supply: challenge and chance for economy and state
Energy Technology Data Exchange (ETDEWEB)
Casper, W
1976-01-01
The imprint left by the 1973 oil embargo makes all nations aware of their dependence upon this and other raw materials. The author says the brunt of the embargo has dealt a heavier blow than has been realized on industrial nations and developing countries alike. The drastic decline of raw material prices has had threatening consequences for a number of raw-material-producing developing countries, making some nations unite for the purpose of market regulation. The cartel-like union of copper-producing countries is cited; producers of bauxite, iron ore, and tungsten have united; and some producers of tin have united. So far, the attempt to apply the oil strategy to other raw materials has not achieved the desired results; however, raw materials are no longer just a phase of the industrial process but have become a political matter of prime importance. (MCW)
-
7 CFR 58.332 - Segregation of raw material.
2010-01-01
... 7 Agriculture 3 2010-01-01 2010-01-01 false Segregation of raw material. 58.332 Section 58.332... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Operations and Operating Procedures § 58.332 Segregation of raw material. The milk and cream received at the dairy plant shall meet...
-
Price stabilization for raw jute in Bangladesh
Takamasa Akiyama; Varangis, Panos
1991-01-01
Fluctuating prices for raw jute have been viewed as contributing to economic problems in the jute subsector. Price fluctuations were thought to reduce the jute farmers'welfare and there has been concern about the costs of parastatals'stocking operations in attempts to stabilize jute prices and incomes. The authors examine these fluctuations and analyze policies that might reduce them. They find that price fluctuations for raw jute reduce farmers'welfare only slightly because farmers'activitie...
-
Biological and physiological changes in rats fed some raw and irradiated legumes
International Nuclear Information System (INIS)
Elwakeil, F.A.; Farag, H.; Sharabash, M.T.M.; Diaa Eldin, M.; Mahrous, S.R.
1995-01-01
Body weight of rats fed on raw kidney beans, soybeans, broad beans, chick peas and lupines suftered from poor growth due to the presence of some anti nutritional factors in these pulses. The processed soybeans, kidney beans, bread beans and lupines at 10 KGy could not correct the growth of rats kept on their diets for 8 weeks while irradiated chick beans at 10 KGy indicating some effect of the irradiation in this respect. When extracts of raw legumes were injected by intraperitoneal route, Ld 5 0 were found to be 125, 300, and 1800 mg/kg, for raw kidney beans, raw soybeans, and raw broad beans respectively. However, injecting the extracts of raw chick peas and raw lupines did not kill the rats even at higher concentration levels of 300 mg/kg. Similar results were obtained with irradiated chick peas and lupines (10 KGy). Meanwhile, post irradiation treatment of kidney beans, soybeans, and broad beans caused the Ld 5 0 to be 250,400, and 2000 mg/kg for the above pulses respectively. Both raw and irradiated kidney beans and raw soybeans were most active in stimulating pancreas and liver growth and reducing spleen weight. Irradiated soybeans showed a moderate, but significant, increase in liver weight only. However, rats which received both raw and irradiated broad beans, chick peas and lupins in their diets did not suffer any pancreatic, liver hypertrophy or spleen atrophy. The hematological parameters investigated showed that there was no significant differences between rat groups fed on either the raw or the irradiated legumes. 5 tabs
-
Analytical techniques for characterization of raw materials in cell culture media
Directory of Open Access Journals (Sweden)
Sharma Chandana
2011-11-01
Full Text Available Abstract Raw materials are a critical part of any cell culture medium; therefore, it is of utmost importance to understand and characterize them for high-quality product. The raw material characterization (RMC program at SAFC focuses on individual screening of raw materials both analytically and biologically. The goal of the program is to develop the best-in-class knowledge base of the raw materials used in SAFC’s media formulations and their impact on performance of products.
-
Effect of ionising radiation on shelf life and potency of herbal raw materials
International Nuclear Information System (INIS)
Rama Bhat, P.; Prajna, P.S.; Sanjeev, Ganesh; Padyana, Subramanya; Maurya, D.K.
2013-01-01
Medicinal herbs are involving from fringe to mainstream use with a greater number of people seeking remedies and health approaches free from side effects caused by synthetic chemicals. Unfortunately, the number of reports of people experiencing negative effects, caused by the use of herbal drugs, has also been increasing. There may be various reasons for such problems, poor quality of herbal medicines due to insufficient attention being paid to the quality assurance and control of these products. Plants are associated with their own microflora, in addition to that soil and air act as main inoculum source for causing contamination in crude herbs along with other field practices like harvesting, handling and packing. The study was aimed to determine the type, level of bacterial and fungal load and feasibility of electron beam irradiation to hygenise the commonly used herbal raw materials using electron beam radiation with three different dosages viz., 8 kGy, 12 kGy, 15 kGy. Irradiated and control samples were analysed for microbial load and biochemical compositions. In present study, microbial load was proportionately reduced with increase in dosage compared to non-irradiated samples. Results indicated that non-irradiated samples were highly contaminated with microbial load. E. coli and Staphylococcus spp. were predominant among the bacterial contaminants at varying levels. The fungi enumerated from raw materials includes species of Penicillium, Rhizopus, Mucor and Aspergillus. Minimum variation was recorded in the carbohydrate, protein, phenolic, tannin and ascorbic acid content of the herb samples with irradiation treatment. (author)
-
Plastic raw materials in Neolithic pottery production
Directory of Open Access Journals (Sweden)
Alexander A. Bobrinsky
2012-12-01
Full Text Available The paper is dedicated to the investigation of various natural silts as the most ancient type of raw material used in pottery production. The authors describe the specific features of the composition of plain and mountain silts, and discover the same features in ancient ceramics from different regions in Russia. It can be concluded that silts were the earliest raw material used, a tradition that faded away during the evolution of pottery production.
-
Study of the incorporation of marble and granite wastes in the raw material to produce glass wool
International Nuclear Information System (INIS)
Rodrigues, Girley Ferreira; Junca, Eduardo; Telles, Victor Bridi; Espinosa, Denise Crocce Romano; Tenorio, Jorge Alberto Soares; Alves, Joner Oliveira
2010-01-01
The study aimed to characterize materials obtained from the melted mixture containing marble and granite wastes, and also chemical reagents. Using the characterization results was defined the feasibility of reuse of the marble and granite wastes, through the incorporation in the raw material to produce glass wool (a material with great consumer market as thermo-acoustic insulator). The batch was poured in a water-filled recipient and also in a Herty viscometer at temperatures of 1400, 1450 and 1500 °C. Samples of produced materials were characterized by morphology using Scanning Electron Microscopy, by atomic structure using X-ray Diffraction, and by thermal behavior using Differential Thermal Analysis. The total amount of marble and granite wastes can reach about 79% replacement in relation to the total weight of the raw material used in the glass wool production. (author)
-
Order acceptance in food processing systems with random raw material requirements
Kilic, Onur A.; van Donk, Dirk Pieter; Wijngaard, Jacob; Tarim, S. Armagan
This study considers a food production system that processes a single perishable raw material into several products having stochastic demands. In order to process an order, the amount of raw material delivery from storage needs to meet the raw material requirement of the order. However, the amount
-
Raw materials for aluminium production
International Nuclear Information System (INIS)
Galushkin, N.V.
1995-01-01
This chapter of monograph is devoted to to raw materials which used in aluminium production. Therefore, the using of alumina, and fluoride salts in aluminium production was considered. The physical properties of alumina were studied.
-
Determination Of Work Indexes Of Basic Ceramic Raw Materials
İPEK, Halil; UÇBAŞ, Yaşar
2017-01-01
In this study, the grindability of basic ceramic raw materials have been investigated by using Bond grindability test and the results have been compared. Bond grindability test results show that work indexes of raw materials are dependent on their hardnesses.
-
Hygienic and other aspects of raw milk vending machines
DANIEL, Radovan
2011-01-01
The aim of this work was to evaluate opportunities of raw milk sales. The questionnaire was submitted to respondents, which assessed the direct sale of milk, consumption, awareness about milk quality connecting with the sales of raw milk using a vending machines.
-
High temperature cement raw meal flowability
DEFF Research Database (Denmark)
Maarup, Claus; Hjuler, Klaus; Dam-Johansen, Kim
2014-01-01
The flowability of cement raw meal is investigated at temperatures up to 850°C in a specially designed monoaxial shear tester. Consolidation stresses of 0.94, 1.87 and 2.79kPa are applied. The results show that the flowability is reduced as temperature is increased above 550°C, indicated by incre......The flowability of cement raw meal is investigated at temperatures up to 850°C in a specially designed monoaxial shear tester. Consolidation stresses of 0.94, 1.87 and 2.79kPa are applied. The results show that the flowability is reduced as temperature is increased above 550°C, indicated...
-
International Nuclear Information System (INIS)
Kostenko, L.D.; Dikun, P.P.
1986-01-01
Products prepared from wood (straw, peat) using different methods of treatment of the initial raw material and semifinished products - radiolysis by gamma-radiation and fast electrons, alkali or acid hydrolysis, treatment with ultrasound have been studied. Despite the differences in technological method in some experiments increased concentrations of benz (a) pyrene (as compared with its content in the initial raw material) are detected in the products. It can not be accepted as an unambiguous proof of carcinogene formation as a result of the technological process. Nevertheless it is recommended to take the phenomenon into account when evaluating degree of carcinogenous danger of such products for living organisms
-
Traceability System Model for Quality Gelatin Raw Material of Cattle Hides
Directory of Open Access Journals (Sweden)
S Nur
2010-09-01
Full Text Available Several criteria must be accomplished within the provision of quality products in terms of the types of materials, the processing methods and effort to get it. Traceability system involves various parties that have different needs and goals in the process of supplying raw materials. Hence, there is a need for institutional systems engineering that can organize and manage the tracking process, the procurement of raw materials that guarantee the origin of gelatin raw materials, and facilitate the industry and customer to create a standardized quality of product. The purpose of the study formulates the institutional tracking models of gelatin raw material from cattle hide based on various criteria and assessment of the expert opinion. The methods used in this study were Interpretative structural modeling to formulate a representation of institutional tracking efficiently and analytical hierarchy process to determine the tracking strategy of industrial gelatin raw materials from cowhide. The results obtained from the study were some key elements of institutional tracking model for industrial gelatin raw materials from cowhide and the traceability strategies for industrial raw materials from cattle hide gelatin Indonesia. (Animal Production 12(3: 190-198 (2010 Key Words: traceability, institutional model, cattle hide, gelatin
-
Raw starch digestion by. alpha. -amylase and glucoamylase from Chalara paradoxa
Energy Technology Data Exchange (ETDEWEB)
Monma, Mitsura; Yamamoto, Yoshihiro; Kagei, Norio; Kainuma, Keiji
1989-10-01
Glucoamylase and {alpha}-amylase of Chalara paradoxa were separated by hydrophobic column chromatography using butyl-Toyopearl 650M. The {alpha}-amylase showed the highest activity at pH 5.5 and 45{sup 0}C, and was stable in the pH range of 5.5-6.5 and at temperatures lower than 40{sup 0}C. The glucoamylase showed the highest activity at pH 5.0 and 45{sup 0}C, and was stable in the pH range of 4.0-7.5 and at temperatures lower than 45{sup 0}C. The molecular mass of the {alpha}-amylase and glucoamylase estimated by SDS polyacrylamide gel electrophoresis was 80,000 and 68,000, respectively. Both glucoamylase and {alpha}-amylase could digest more effectively raw rice starch and raw corn starch than raw sago starch and raw potato starch. 2% raw rice starch in 10 ml solution was digested by more than 90% by 100 units of each amylase. When these amylases were used combined, raw corn starch was more effectively digested than they were used singly. This cooperative action in raw corn starch digestion was also observed when C. paradoxa {alpha}-amylase and R. niveus glucoamylase were combined. (orig.).
-
Quality control of raw cows' milk by headspace analysis
Hettinga, K.A.; Valenberg, van H.J.F.; Hooijdonk, van A.C.M.
2008-01-01
This study investigated whether headspace analysis of volatile components can be used for monitoring the quality of raw cows¿ milk. The detection of different quality defects caused by cows¿ feed, microbiological and chemical contamination, as well as enzymatic deterioration was studied. Fresh raw
-
D-Zero muon readout electronics design
International Nuclear Information System (INIS)
Baldin, B.; Hansen, S.; Los, S.; Matveev, M.; Vaniev, V.
1996-11-01
The readout electronics designed for the D null Muon Upgrade are described. These electronics serve three detector subsystems and one trigger system. The front-ends and readout hardware are synchronized by means of timing signals broadcast from the D null Trigger Framework. The front-end electronics have continuously running digitizers and two levels of buffering resulting in nearly deadtimeless operation. The raw data is corrected and formatted by 16- bit fixed point DSP processors. These processors also perform control of the data buffering. The data transfer from the front-end electronics located on the detector platform is performed by serial links running at 160 Mbit/s. The design and test results of the subsystem readout electronics and system interface are discussed
-
Renewable raw materials in the field of industry; Nachwachsende Rohstoffe in der Industrie
Energy Technology Data Exchange (ETDEWEB)
Peters, D.
2006-07-01
Being used to the practiced processing of raw materials for many decades the industry had to tap the advantage of renewable raw materials again. Conventional processing methods had to be changed and to be newly developed. This has been a rewarding task considering the ecological advantages but also considering the interesting markets for products based upon renewable raw materials. Today the German industry above all the chemical industry again processes agricultural and forestal raw materials to a considerable extent. Ten percent of the raw materials processed by the chemical industry are renewable. The wood processing industry is an important economic sector that achieves a value creation with the raw material wood exceeding the value creation of other industries by far. This brochure gives an overview of the possible substances, which are processed from renewable raw materials in Germany and it shows the important role that agricultural raw materials and wood already play for the industry nowadays. (orig.)
-
Nutrients and antinutrients composition of raw, cooked and sun ...
African Journals Online (AJOL)
Nutrients and antinutrients composition of raw, cooked and sun-dried sweet potato leaves. ... African Journal of Food, Agriculture, Nutrition and Development ... This study aimed to determine nutrient (iron, calcium, vitamin A and ascorbic acid) and anti-nutrient (oxalates and polyphenols) contents in raw, cooked and dried ...
-
Atmospheric Turbulence Estimates from a Pulsed Lidar
Pruis, Matthew J.; Delisi, Donald P.; Ahmad, Nash'at N.; Proctor, Fred H.
2013-01-01
Estimates of the eddy dissipation rate (EDR) were obtained from measurements made by a coherent pulsed lidar and compared with estimates from mesoscale model simulations and measurements from an in situ sonic anemometer at the Denver International Airport and with EDR estimates from the last observation time of the trailing vortex pair. The estimates of EDR from the lidar were obtained using two different methodologies. The two methodologies show consistent estimates of the vertical profiles. Comparison of EDR derived from the Weather Research and Forecast (WRF) mesoscale model with the in situ lidar estimates show good agreement during the daytime convective boundary layer, but the WRF simulations tend to overestimate EDR during the nighttime. The EDR estimates from a sonic anemometer located at 7.3 meters above ground level are approximately one order of magnitude greater than both the WRF and lidar estimates - which are from greater heights - during the daytime convective boundary layer and substantially greater during the nighttime stable boundary layer. The consistency of the EDR estimates from different methods suggests a reasonable ability to predict the temporal evolution of a spatially averaged vertical profile of EDR in an airport terminal area using a mesoscale model during the daytime convective boundary layer. In the stable nighttime boundary layer, there may be added value to EDR estimates provided by in situ lidar measurements.
-
Ishihara, Ayaka; Hashimoto, Etaro; Ishioka, Haruhiko; Kobayashi, Hiroyuki; Gomi, Harumi
2018-01-01
Meningitis caused by the zoonotic pathogen Campylobacter fetus in immunocompetent adults is rare. We report a 48-year-old Japanese woman with no underlying disease who was found to have meningitis caused by C. fetus . Both C. fetus subsp. fetus and C. fetus subsp. venerealis were isolated from the cerebrospinal fluid culture. The mode of infection in our patient was considered to be associated with the consumption of raw beef and raw cattle liver on a regular basis. Public awareness and education to avoid the consumption of raw or undercooked meat might help prevent C. fetus meningitis.
-
CASSINI RSS RAW DATA SET - SROC20 V1.0
National Aeronautics and Space Administration — The Cassini Radio Science Saturn Ring and Atmospheric Occultation experiments (SROC20) Raw Data Archive is a time-ordered collection of radio science raw data...
-
Raw materials in the manufacture of biotechnology products: regulatory considerations.
Cordoba-Rodriguez, Ruth
2010-01-01
The Food and Drug Administration's Pharmaceutical cGMPs for the 21st Century initiative emphasizes science and risk-based approaches in the manufacture of drugs. These approaches are reflected in the International Conference on Harmonization (ICH) guidances ICH Q8, Q9, and Q10 and encourage a comprehensive assessment of the manufacture of a biologic, including all aspects of manufacture that have the potential to affect the finished drug product. Appropriate assessment and management of raw materials are an important part of this initiative. Ideally, a raw materials program should strive to assess and minimize the risk to product quality. With this in mind, risk-assessment concepts and control strategies will be discussed and illustrated by examples, with an emphasis on the impact of raw materials on cell substrates. Finally, the life cycle of the raw material will be considered, including its potential to affect the drug product life cycle. In this framework, the supply chain and the vendor-manufacturer relationship will be explored as important parts of an adequate raw materials control strategy.
-
Incorporation of Listeria monocytogenes strains in raw milk biofilms.
Weiler, Christiane; Ifland, Andrea; Naumann, Annette; Kleta, Sylvia; Noll, Matthias
2013-02-01
Biofilms develop successively on devices of milk production without sufficient cleaning and originate from the microbial community of raw milk. The established biofilm matrices enable incorporation of pathogens like Listeria monocytogenes, which can cause a continuous contamination of food processing plants. L. monocytogenes is frequently found in raw milk and non-pasteurized raw milk products and as part of a biofilm community in milk meters and bulk milk tanks. The aim of this study was to analyze whether different L. monocytogenes strains are interacting with the microbial community of raw milk in terms of biofilm formation in the same manner, and to identify at which stage of biofilm formation a selected L. monocytogenes strain settles best. Bacterial community structure and composition of biofilms were analyzed by a cloning and sequencing approach and terminal restriction fragment length polymorphism analysis (T-RFLP) based on the bacterial 16S rRNA gene. The chemical composition of biofilms was analyzed by Fourier transform infrared spectroscopy (FTIR), while settled L. monocytogenes cells were quantified by fluorescence in situ hybridization (FISH). Addition of individual L. monocytogenes strains to raw milk caused significant shifts in the biofilm biomass, in the chemical as well as in the bacterial community composition. Biofilm formation and attachment of L. monocytogenes cells were not serotype but strain specific. However, the added L. monocytogenes strains were not abundant since mainly members of the genera Citrobacter and Lactococcus dominated the bacterial biofilm community. Overall, added L. monocytogenes strains led to a highly competitive interaction with the raw milk community and triggered alterations in biofilm formation. Copyright © 2012 Elsevier B.V. All rights reserved.
-
MARS GLOBAL SURVEYOR RAW DATA SET - CRUISE V1.0
National Aeronautics and Space Administration — The Mars Global Surveyor (MGS) Radio Science (RS) Raw Data Archive (RDA) is a time-ordered collection of raw and partially processed data collected during the MGS...
-
Radiation hygienization of raw sewage sludge
International Nuclear Information System (INIS)
Shah, M.R.; Lavale, D.S.; Rawat, P.; Benny, P.G.; Sharma, A.K.; Dey, G.R.; Bhave, V.
2001-01-01
'Radiation treatment of municipal sewage sludge can achieve resource conservation and recovery objectives. The liquid sludge irradiator of Sludge Hygienization Research Irradiator at Baroda (India) was operated for generating data on treatment of raw sludge containing 3-4 % solids. The plant system was modified for irradiating raw sludge without affecting basic irradiator initially designed to treat digested sludge. Hourly samples were analysed for estimation of disinfection dose requirement. Sand separated from the sludge was used as in-situ dosimeter by making use of its thermoluminescence property. Investigations are being carried out for regrowth of Total Coliforms in the sludge samples from this irradiator. Possibility of inadequate treatment due to geometric configuration of irradiator is being checked. (author)
-
Uninterrupted heat-treatment of starch raw materials
Energy Technology Data Exchange (ETDEWEB)
Bronshtein, D Z
1958-01-01
A setup is presented, with a Rekord grinder, a Khronos scale, and other equipment of Soviet manufacture, in which oats, rye, wheat, and other grains are treated at 42 to 45 degrees prior to their use as raw materials in the ethanol industry. These materials are analyzed with respect to H/sub 2/O, starch, bulk, weight, screen analysis, and the final ethanol yields/ton of such raw materials. In a three year run in plant, this heat-treatment was advantageous, as compared to the former treatment of the starch materials.
-
Uninterrupted heat-treatment of starch raw materials
Energy Technology Data Exchange (ETDEWEB)
Bronshtein, D Z
1958-01-01
A setup is presented, with a Rekord grinder, a Khronos scale, and other equipment of Soviet manufacture, in which oats, rye, wheat, and other grains are treated at 42 to 45/sup 0/ prior to their use as raw materials in the ethanol industry. These materials are analyzed with respect to H/sub 2/O, starch, bulk weight, screen analysis, and the final ethanol yields/ton of such raw materials. In a three year run in a plant, this heat-treatment was advantageous, as compared to the former treatment of the starch materials.
-
Titanium. Properties, raw datum surface, physicochemical basis and fabrication technique
International Nuclear Information System (INIS)
Garmata, V.A.; Petrun'ko, A.N.; Galitskij, N.V.; Olesov, Yu.G.; Sandler, R.A.
1983-01-01
On the nowadays science and technology achievements the complex of titanium metallurgy problems comprising raw material base, physico-chemical basis and fabrication technique, properties and titanium usage fields is considered for the first time. A particular attention is given to raw material base, manufacturing titanium concentrates and titanium tetrachloride, metallothermal reduction, improvement of metal quality. Data on titanium properties are given, processes of titanium powder metallurgy, scrap and waste processing, problems of economics and complex raw material use are considered
-
Scrap automotive electronics: A mini-review of current management practices.
Cucchiella, Federica; D'Adamo, Idiano; Rosa, Paolo; Terzi, Sergio
2016-01-01
End-of-life vehicles, together with waste from electric and electronic equipment, are known as an important source of secondary raw materials. For many years, their recovery has allowed the restoring of great amounts of metals for new cars production. This article provides a comprehensive mini-review on the end-of-life vehicles recycling topic between 2000 and 2014, with a particular focus on automotive electronics recycling. In fact, in the last years, experts focused their attention on a better exploitation of automotive shredder residue fraction, but not sufficiently on eventual electronic scraps embedded in it. Hence, studies assessing the value embedded in these scraps are rarely available in literature, causing an important gap in both recycling policies and research. The fact that, at present, the management of electronic control units (the most valuable component among automotive electronic equipment) is, as yet, off the radar in both end-of-life vehicles and waste from electric and electronic equipment Directives demonstrates the theory. Of course, their recycling would not contribute in a relevant way to reach the weighted-based recycling and recovery targets characterising current regulations, but would be very important under a critical raw materials recovery view. Results coming from the literature analysis confirm these assumptions. © The Author(s) 2015.
-
United States Climate Reference Network (USCRN) Raw Observations from Datalogger
National Oceanic and Atmospheric Administration, Department of Commerce — Datalogger files are raw USCRN data. However, instead of being collected via satellite, the raw data are collected from station dataloggers (also referred to as...
-
Silica nanoparticles produced by DC arc plasma from a solid raw materials
Kosmachev, P. V.; Vlasov, V. A.; Skripnikova, N. K.
2017-05-01
Plasma synthesis of SiO2 nanoparticles in experimental atmospheric pressure plasma reactor on the basis of DC arc plasma generator was presented in this paper. Solid high-silica raw materials such as diatomite from Kamyshlovskoye deposit in Russia, quartzite from Chupinskoye deposit in Russia and milled window glass were used. The obtained nanoparticles were characterized based on their morphology, chemical composition and size distribution. Scanning electron microscopy, laser diffractometry, nitrogen absorption (Brunauer-Emmett-Teller method), X-ray photoelectron spectroscopy and energy-dispersive X-ray spectroscopy were used to characterize the synthesized products. The obtained silica nanoparticles are agglomerated, have spherical shape and primary diameters between 10-300 nm. All samples of synthesized nanopowders were compared with commercial nanopowders.
-
RAW CHICKEN LEG AND BREAST SENSORY EVALUATION
Directory of Open Access Journals (Sweden)
Octavian Baston
2010-01-01
Full Text Available In the paper we presented a method of sensorial evaluation for chicken meat (red and white. This is a descriptive method of analysis. It was perform with trained assessors for chicken refrigerated raw meat organoleptical evaluation. The sensorial attributes considered were: external aspect of anatomical part of chicken analyzed by slime, the surface odor, the skin and muscle color and muscular elasticity. Color was determined for the skin and white and red muscles. Our scale of analysis is formed by three values that characterize each quality attribute. The trained assessor appreciated the sensorial quality of raw anatomical part of chicken as excellent, acceptable and unacceptable. The objectives were: to establish the sensorial attributes to be analyzed for each type of muscular fiber, to describe the quality of each considered attribute and to realize a sensorial scale of quantification for the considered sensorial attributes. Our purpose was to determine the quality of the red and white refrigerated raw chicken anatomical parts (respectively for legs and breasts after one week of storage.
-
Raw Data (ASCII format) - PLACE | LSDB Archive [Life Science Database Archive metadata
Lifescience Database Archive (English)
Full Text Available List Contact us PLACE Raw Data (ASCII format) Data detail Data name Raw Data (ASCII format) DOI 10.18908/lsd...miter About This Database Database Description Download License Update History of This Database Site Policy | Contact Us Raw Data (ASCII format) - PLACE | LSDB Archive ...
-
Raw material studies of West Central Serbia
Directory of Open Access Journals (Sweden)
Vera Bogosavljević Petrović
2014-03-01
Full Text Available This paper deals with raw material problems in the territory of West Central Serbia geologically determined as the Čačak-Kraljevo (or West Morava basin. Our research is presented through the most striking case studies, Lojanik, Vlaška Glava and Lazac. The Lojanik hill is a silicified forest by origin. It has occasionally been in use from the earliest periods of prehistory until today as a source of black and ochre-coloured flint, opal and silicified wood. A detailed prospection, including the mapping of surface finds using square nets, was conducted during two research campaigns.The Vlaška Glava is an open-air Palaeolithic site at which artefacts made of white, ochre, red, brown and black chert, silicified magnesite, volcanic and metamorphic rocks were found. Our research of primary and secondary geological deposits in the vicinity of the site showed equivalent raw material. We also found an interesting primary deposit of high quality bluish grey flint with outcrop activities (Workshop 1.The Lazac shaft is a contemporary magnesite mine, recently abandoned because of the high percentage of silicon-dioxide. We determined the same raw material in collections found at nearby Neolithic sites. Certain similarities between the wooden support systems of ore exploration in the Middle Ages and modern times were established at the entrance of the shaft.Our research in the territory of the West Morava basin resulted in reconstruction of some links between geological deposits and settlements and also creation of a relevant base for future raw material studies.
-
Determination of essential nutrients in raw milk
Directory of Open Access Journals (Sweden)
Penphimon Phongphanphanee
2006-03-01
Full Text Available Milk production in Thailand has gradually increased since 1961. Occasional oversupply of raw milk has become one of dairy farmers' major problems. Increasing the consumption of milk by making use of its separated nutrients may offer a solution. This study was to assess the composition of raw milk produced in Thailand, which included fat, protein, lactose, solid-not-fat (SNF and total solid (TS. A large dairy cooperatives in Saraburi Province was selected for the study. About 9% of its total members, constituting 108 farms, were randomly chosen. They consisted of small size (less than 20 cows/farm, medium size (21-100 cows/farm and large size (>100 cows/farm. The majority was medium-size. Raw milk from each farm was sampled at the delivery site of the cooperatives in the morning. Milk data of the 108 farms were compiled at 3 different periods between February and July 2003. The raw milk was analyzed by the Fourier Transform Infrared Analysis (FTIR using MilkoScan FT6000. The results showed the average fat content of 3.50±0.47%, protein of 3.13±0.16%, lactose of 4.59±0.12%, SNF of 8.42±0.20%, and TS of 11.92±0.54%. The samples were superior in all of the nutrients as compared to the standard levels set by the Department of Livestock Development, except for TS. This indicates the possibility of a local production of milk nutrients such as lactose and protein as ingredients for the pharmaceutical and health food industries.
-
Sulfur Release from Cement Raw Materials during Solid Fuel Combustion
DEFF Research Database (Denmark)
Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter
2011-01-01
During combustion of solid fuels in the material inlet end of cement rotary kilns, local reducing conditions can occur and cause decomposition of sulfates from cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2 concentration, which may cause...... deposit formation in the kiln system. SO2 release from cement raw materials during combustion of solid fuels has been studied experimentally in a high temperature rotary drum. The fuels were tire rubber, pine wood, petcoke, sewage sludge, and polypropylene. The SO2 release from the raw materials...
-
Quality and Sensorial Characteristics of Raw-Vegan Bars
Liana Claudia Salanţă; Maria Tofană; Sonia Socaci; Cristina Barta; Carmen Pop
2015-01-01
Increased consumer interest in healthier food products is driven by a variety of factors including growing awareness of the link between diet and health, the desire to age ‘gracefully’ by maintaining good health, greater convenience in meeting nutritional needs and preventing chronic diseases. In raw food diet, food is consumed predominantly or exclusively as uncooked and unprocessed raw food; the main components of the diet are fruits, nuts, seeds, and sprouted grains and beans. The aim of t...
-
raw data collected from Malvern Instrument
U.S. Environmental Protection Agency — These are raw data/image files from the Malvern Zetasizer Instrument. This dataset is associated with the following publication: Buse, H., J. Hoelle, C. Muhlen, and...
-
Iron zircon pigment synthesis: Proposal of a mixing index for the raw materials mixtures
International Nuclear Information System (INIS)
Zumaquero, E.; Ortsb, M.J.; Sanz, V.; Mestre, S.
2017-01-01
Iron zircon coral pigments are very interesting from an industrial point of view because of their high colouring power and their stability at high temperatures. However, the pigment's synthesis is particularly troublesome due to its specific reaction mechanism. As an encapsulated pigment it becomes very important how the raw materials are distributed in the reaction mixture. To evaluate the effectiveness of the mixing process, it would be convenient to define a parameter, that is the mixing index, to estimate the degree of homogeneity of the system. In the current investigation, a mixing index is proposed derived from the power spectrum of Fourier transform of scanning electron microscope (SEM) images of the raw material mixture. Concretely, the number of pixels in a certain range of values in the image of the power spectrum, seems to behave relatively well as mixing index. This index allows us to distinguish between samples with different zirconia and iron oxide used as precursors. The proposed mixing index seems to be related to the colouring power of the final pigment when the synthesis generates enough zircon to encapsulate hematite particles. [es
-
Characterization of sugar cane bagasse ash as raw material for the production of ceramics
International Nuclear Information System (INIS)
Fredericci, C.; Indelicato, R.L.; Ferreira Neto, J.B.; Ribeiro, T.R.; Landgraf, F.J.G.; Silva, G.F.B. Lenz e
2012-01-01
The aim of this paper was to analyze the sugar cane bagasse ash from three Sugar and Alcohol Plant of the State of Sao Paulo - Brazil. We intend to show the discrepancies between them, so that this raw material could be used with greater quality control in ceramic industries. The bagasse were analyzed by differential scanning calorimetry (DSC), thermogravimetry (TG) and scanning electron microscopy. The ashes were analyzed by X-ray diffraction, X-ray fluorescence, scanning electron microscopy, energy dispersive spectroscopy, and granulometric separation. The results indicated that the content of SiO 2 ranging from 50-80% by weight depends on the granulometry of the bagasse and on the region where it was collected. The analyses of X-ray diffraction indicate SiO 2 , Fe 2 O 3 , K 2 SO 4 and Mg 2 P 2 O 7 as crystalline phases. (author)
-
Tracing and control of raw materials sourcing for vaccine manufacturers.
Faretra Peysson, Laurence
2010-05-01
The control of the raw materials used to manufacture vaccines is mandatory; therefore, a very clear process must be in place to guarantee that raw materials are traced. Those who make products or supplies used in vaccine manufacture (suppliers of culture media, diagnostic tests, etc.) must apply quality systems proving that they adhere to certain standards. ISO certification, Good Manufacturing Practices for production sites and the registration of culture media with a 'Certificate of Suitability' from the European Directorate for the Quality of Medicines and Healthcare are reliable quality systems pertaining to vaccine production. Suppliers must assure that each lot of raw materials used in a product that will be used in vaccine manufacture adheres to the level of safety and traceability required. Incoming materials must be controlled in a single 'Enterprise Resource Planning' system which is used to document important information, such as the assignment of lot number, expiration date, etc. Ingredients for culture media in particular must conform to certain specifications. The specifications that need to be checked vary according to the ingredient, based on the level of risk. The way a raw material is produced is also important, and any aspect relative to cross-contamination, such as the sanitary measures used in producing and storing the raw material must be checked as well. In addition, suppliers can reduce the risk of viral contamination of raw materials by avoiding purchases in countries where a relevant outbreak is currently declared. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.
-
The use of raw and acid-pretreated bivalve mollusk shells to remove metals from aqueous solutions
International Nuclear Information System (INIS)
Liu Yang; Sun Changbin; Xu Jin; Li Youzhi
2009-01-01
Heavy metal removal from industrial wastewater is not only to protect living organisms in the environment but also to conserve resources such as metals and water by enabling their reuse. To overcome the disadvantage of high cost and secondary pollution by the conventional physico-chemical treatment techniques, environmentally benign and low-cost adsorbents are in demand. In this study, the use of raw and acid-pretreated bivalve mollusk shells (BMSs) to remove metals from aqueous solutions with single or mixed metal was evaluated at different BMSs doses, pH and temperatures in batch shaking experiments in laboratory conditions. When the BMSs were used to treat CuSO 4 .5H 2 O solution, the copper sorption capacities of the raw and acid-pretreated BMSs were approximately 38.93 mg/g and 138.95 mg/g, respectively. The copper removal efficiency (CRE) of the raw BMSs became greatly enhanced with increasing initial pH, reaching 99.51% at the initial pH 5. Conversely, the CRE of the acid-pretreated BMSs was maintained at 99.48-99.52% throughout the pH range of 1-5. Furthermore, the CRE values of the raw and acid-pretreated BMSs were not greatly changed when the temperature was varied from 15 deg. C to 40 deg. C. In addition, the CRE value of the raw BMSs was maintained for 12 cycles of sorption-desorption with a CRE of 98.4% being observed in the final cycle. Finally, when the BMSs were used to treat electroplating wastewater, the removal efficiencies (REs) of the raw BMSs were 99.97%, 98.99% and 87% for Fe, Zn and Cu, respectively, whereas the REs of the acid-pretreated BMSs were 99.98%, 99.43% and 92.13%, respectively. Ion exchange experiments revealed that one of mechanisms for metal sorption by the BMSs from aqueous solution is related to ion exchange, especially between the metal ions in the treated solution and Ca 2+ from BMSs. Infrared absorbance spectra analysis indicated that the acid pretreatment led to occurrence of the groups (i.e. -OH, -NH, C=O and S=O) of
-
The use of raw and acid-pretreated bivalve mollusk shells to remove metals from aqueous solutions.
Liu, Yang; Sun, Changbin; Xu, Jin; Li, Youzhi
2009-08-30
Heavy metal removal from industrial wastewater is not only to protect living organisms in the environment but also to conserve resources such as metals and water by enabling their reuse. To overcome the disadvantage of high cost and secondary pollution by the conventional physico-chemical treatment techniques, environmentally benign and low-cost adsorbents are in demand. In this study, the use of raw and acid-pretreated bivalve mollusk shells (BMSs) to remove metals from aqueous solutions with single or mixed metal was evaluated at different BMSs doses, pH and temperatures in batch shaking experiments in laboratory conditions. When the BMSs were used to treat CuSO(4)x5H(2)O solution, the copper sorption capacities of the raw and acid-pretreated BMSs were approximately 38.93 mg/g and 138.95 mg/g, respectively. The copper removal efficiency (CRE) of the raw BMSs became greatly enhanced with increasing initial pH, reaching 99.51% at the initial pH 5. Conversely, the CRE of the acid-pretreated BMSs was maintained at 99.48-99.52% throughout the pH range of 1-5. Furthermore, the CRE values of the raw and acid-pretreated BMSs were not greatly changed when the temperature was varied from 15 degrees C to 40 degrees C. In addition, the CRE value of the raw BMSs was maintained for 12 cycles of sorption-desorption with a CRE of 98.4% being observed in the final cycle. Finally, when the BMSs were used to treat electroplating wastewater, the removal efficiencies (REs) of the raw BMSs were 99.97%, 98.99% and 87% for Fe, Zn and Cu, respectively, whereas the REs of the acid-pretreated BMSs were 99.98%, 99.43% and 92.13%, respectively. Ion exchange experiments revealed that one of mechanisms for metal sorption by the BMSs from aqueous solution is related to ion exchange, especially between the metal ions in the treated solution and Ca(2+) from BMSs. Infrared absorbance spectra analysis indicated that the acid pretreatment led to occurrence of the groups (i.e. -OH, -NH, C=O and S
-
Energy Technology Data Exchange (ETDEWEB)
Wenig, Barbara
2007-07-01
Regenerative raw materials are the basis for a multiplicity of environmentally friendly products. Regenerating raw materials fascinate by special qualities and offer the possibility of preserving only restricted existing fossil resources and climatic friendly managing. The review under consideration reports on areas in which vegetable raw materials already are established as well as on future prospects.
-
Trakarnpaiboon, Srisakul; Srisuk, Nantana; Piyachomkwan, Kuakoon; Sakai, Kenji; Kitpreechavanich, Vichien
2017-09-14
In the present study, solid-state fermentation for the production of raw starch degrading enzyme was investigated by thermotolerant Rhizopus microsporus TISTR 3531 using a combination of agro-industrial wastes as substrates. The obtained crude enzyme was applied for hydrolysis of raw cassava starch and chips at low temperature and subjected to nonsterile ethanol production using raw cassava chips. The agro-industrial waste ratio was optimized using a simplex axial mixture design. The results showed that the substrate mixture consisting of rice bran:corncob:cassava bagasse at 8 g:10 g:2 g yielded the highest enzyme production of 201.6 U/g dry solid. The optimized condition for solid-state fermentation was found as 65% initial moisture content, 35°C, initial pH of 6.0, and 5 × 10 6 spores/mL inoculum, which gave the highest enzyme activity of 389.5 U/g dry solid. The enzyme showed high efficiency on saccharification of raw cassava starch and chips with synergistic activities of commercial α-amylase at 50°C, which promotes low-temperature bioethanol production. A high ethanol concentration of 102.2 g/L with 78% fermentation efficiency was achieved from modified simultaneous saccharification and fermentation using cofermentation of the enzymatic hydrolysate of 300 g raw cassava chips/L with cane molasses.
-
Methodology for Evaluating Raw Material Changes to RSRM Elastomeric Insulation Materials
Mildenhall, Scott D.; McCool, Alex (Technical Monitor)
2001-01-01
The Reusable Solid Rocket Motor (RSRM) uses asbestos and silicon dioxide filled acrylonitrile butadiene rubber (AS-NBR) as the primary internal insulation to protect the case from heat. During the course of the RSRM Program, several changes have been made to the raw materials and processing of the AS-NBR elastomeric insulation material. These changes have been primarily caused by raw materials becoming obsolete. In addition, some process changes have been implemented that were deemed necessary to improve the quality and consistency of the AS-NBR insulation material. Each change has been evaluated using unique test efforts customized to determine the potential impacts of the specific raw material or process change. Following the evaluations, the various raw material and process changes were successfully implemented with no detectable effect on the performance of the AS-NBR insulation. This paper will discuss some of the raw material and process changes evaluated, the methodology used in designing the unique test plans, and the general evaluation results. A summary of the change history of RSRM AS-NBR internal insulation is also presented.
-
Directory of Open Access Journals (Sweden)
Sara Daffara
2014-09-01
Full Text Available The Ciota Ciara cave is situated in Monte Fenera’s karst (Borgosesia – Vercelli, at 670 metres above sea level. It is the most important evidence of a Middle Palaeolithic settlement in Piedmont: the cave was used by Homo neanderthalensis during the OIS 5, in a mild-humid period, as proven by faunal remains. The environment was characterized by deciduous woodland and glades. The intersection between different habitats, the presence of lithic raw materials, the karst morphology and water sources were certainly the main factors that encouraged human settlement during the Upper Pleistocene period, between 80.000 and 70.000 BP.In 2009 systematic excavations began in the cave by the University of Ferrara, in partnership with the Soprintendenza per i Beni Archeologici del Piemonte e del Museo di Antichità Egizie. Research focused on the cave’s atrium where three stratigraphic units were investigated: 13, 103 and 14.The exploited raw materials’ characterization were made by the stereo-microscope observations and through the SEM (Scanning Electron Microscope. Several lithologies are represented in different proportion: quartz is the predominant exploited raw material, followed by spongolite, sandstone, mylonite and opal. The archaeological record consists of various typologies of quartz: macro-crystalline pegmatite quartz, micro-crystalline pegmatite quartz and hyaline quartz. All these types of raw materials have been found in the proximity of the archaeological site, within 5 km range.The lithic assemblage is made of flakes, retouched tools, cores and debris. The raw materials exploitation was achieved through the direct percussion technique with various methods: S.S.D.A., discoid and Levallois. The reduction sequences on quartz are complete, although no refitting was found. The reduction sequence is not complete for most part of the other raw materials. The débitage products are small-medium size (1-4 cm and have different morphologies
-
An Immunoassay for Quantification of Contamination by Raw Meat Juice on Food Contact Surfaces.
Chen, Fur-Chi; Godwin, Sandria; Chambers, Edgar
2016-11-01
Raw chicken products often are contaminated with Salmonella and Campylobacter , which can be transmitted from packages to contact surfaces. Raw meat juices from these packages also provide potential media for cross-contamination. There are limited quantitative data on the levels of consumer exposure to raw meat juice during shopping for and handling of chicken products. An exposure assessment is needed to quantify the levels of transmission and to assess the risk. An enzyme-linked immunosorbent assay (ELISA) was developed and validated for quantitative detection of raw meat juice on hands and various food contact surfaces. Analytical procedures were designed to maximize the recovery of raw meat juice from various surfaces: hands, plastic, wood, stainless steel, laminated countertops, glass, and ceramics. The ELISA was based on the detection of a soluble muscle protein, troponin I (TnI), in the raw meat juice. The assay can detect levels as low as 1.25 ng of TnI, which is equivalent to less than 1 μl of the raw meat juice. The concentrations of TnI in the raw meat juices from 10 retail chicken packages, as determined by ELISA, were between 0.46 and 3.56 ng/μl, with an average of 1.69 ng/μl. The analytical procedures, which include swabbing, extraction, and concentration, enable the detection of TnI from various surfaces. The recoveries of raw meat juice from surfaces of hands were 92%, and recoveries from other tested surfaces were from 55% on plastic cutting boards to 75% on laminated countertops. The ELISA developed has been used for monitoring the transfer of raw meat juice during shopping for and handling of raw chicken products in our studies. The assay also can be applied to other raw meat products, such as pork and beef.
-
Assessment of hardened characteristics of raw fly ash blended self-compacting concrete
Directory of Open Access Journals (Sweden)
B. Mahalingam
2016-09-01
Full Text Available Fly ash is widely used as a supplementary cementitious material in concrete. Due to the implementation of new thermal power plants as a consequence of electricity demand, generation of fly ash is noticeably increased. In addition to pozzolana blended cement production, it is very imperative to use raw fly ash in concrete. Earlier research studies investigated the performance of processed fly ash in blended cement production as well as in concrete. In general, ground fly ash is used in blended cement production. A comprehensive study on the performance evaluation of raw fly ash in self-compacting concrete is not available in the existing literature. Moreover, utilization of raw fly ash in special concrete such as self-compacting concrete is essential to comprehend the performance of raw fly ash blended concrete compared to ordinary Portland concrete. Additionally, it will help to achieve maximum utilization of raw fly ash as a supplementary cementitious material rather than disposal as a waste, which eventually leads to several environmental issues. In the study, raw fly ash was collected and is directly used in development of self-compacting concrete. Two mixes were cast and hardened characteristics of blended concrete were investigated. Results from the study showed comparable performance with control concrete. Furthermore, significant reduction in chloride permeability was observed for raw fly ash blended concrete.
-
Consumer use and response to online third-party raw DNA interpretation services.
Wang, Catharine; Cahill, Tiernan J; Parlato, Andrew; Wertz, Blake; Zhong, Qiankun; Cunningham, Tricia Norkunas; Cummings, James J
2018-01-01
With the availability of raw DNA generated from direct-to-consumer (DTC) testing companies, there has been a proliferation of third-party online services that are available to interpret the raw data for both genealogy and/or health purposes. This study examines the current landscape and downstream clinical implications of consumer use of third-party services. Study participants were recruited online from social media platforms. A total of 321 survey respondents reported using third-party services for raw DNA interpretation. Participants were highly motivated to explore raw DNA for ancestral information (67%), individual health implications (62%), or both (40%). Participants primarily used one of seven companies to interpret raw DNA; 73% used more than one. Company choice was driven by the type of results offered (51%), price (45%), and online reviews (31%). Approximately 30% of participants shared results with a medical provider and 21% shared with more than one. Outcomes of sharing ranged from disinterest/discounting of the information to diagnosis of genetic conditions. Participants were highly satisfied with their decision to analyze raw DNA (M = 4.54/5), yet challenges in understanding interpretation results were reported irrespective of satisfaction ratings. Consumers face challenges in understanding the results and may seek out clinical assistance in interpreting their raw DNA results. © 2017 The Authors. Molecular Genetics & Genomic Medicine published by Wiley Periodicals, Inc.
-
ICE CREAM WITH A COMBINED COMPOSITION OF RAW MATERIALS
Directory of Open Access Journals (Sweden)
O. E. Khodyreva
2013-01-01
Full Text Available Dairy products are the product of daily demand. Nowadays actively assimilate new types of raw materials, tech-nology, formulation. One of the propagation methods of enriching dairy products is a combination of milk and vegetable raw materials. The possibility of making a concentrated paste of Jerusalem artichoke in dairy products was investigated. The ice cream sundae "Vanilla" was chosen as the object of research.
-
Comparison of performance between Raw SQL and Eloquent ORM in Laravel
Jound, Ishaq; Halimi, Hamed
2016-01-01
Context. PHP framework Laravel offers three techniques to interact with databases, Eloquent ORM, Query builder and Raw SQL. It is important to select the right database technique when developing a web application because there are pros and cons with each approach. Objectives. In this thesis we will measure the performance of Raw SQL and Eloquent ORM, there is little research on which technique is faster. Intuitively, Raw SQL should be faster than Eloquent ORM, but exactly how much faster nee...
-
Physicochemical characterization of raw materials and co-products from the titanium dioxide industry
International Nuclear Information System (INIS)
Gazquez, M.J.; Bolivar, J.P.; Garcia-Tenorio, R.; Vaca, F.
2009-01-01
The present study was conducted to characterize several raw materials and co-products from the titanium dioxide industry in relation to their elemental composition (major, minor and trace elements), granulometry, mineralogy, microscopic morphology and physical composition. The main objective was to gain basic information for the future potential application of these co-products in fields such as agriculture, construction, civil engineering, etc. Microscopic studies were performed by applying scanning electron microscopy with X-ray microanalysis (SEM-XRMA) while the mineralogical compositions were analysed by means of the X-ray diffraction (XRD) technique. The concentrations of major elements such as Na, Al, Si, Ca, Ti, Fe, S and K were determined by X-ray fluorescence (XRF), while heavy metals and other trace elements were determined by ICP-MS. The physicochemical characterization of the raw materials used in the titanium dioxide industry, in addition to the characterization of the co-products generated, has enabled the evaluation of the degree of fractionation of different elements and compounds between the different co-products, as well as the control of the possible variations in the physicochemical composition of the raw materials throughout the time and the study of the influence of these variations in the characteristics of the obtained co-products. As a main conclusion of our study, it is possible to indicate that the levels of the pollutant elements associated to the co-products analysed were, in general, within safe limits and, therefore, they could potentially be used in composites as fertilizers or for building materials in road construction, etc. Nevertheless, for the specific application of each of these co-products in agriculture, construction and civil engineering, additional studies need to be performed to evaluate their appropriateness for the proposed application, together with specific studies on their health and environmental impact.
-
Physics of the diffusion region in the Magnetospheric Multiscale era
Chen, L. J.; Hesse, M.; Wang, S.; Ergun, R.; Bessho, N.; Burch, J. L.; Giles, B. L.; Torbert, R. B.; Gershman, D. J.; Wilson, L. B., III; Dorelli, J.; Pollock, C. J.; Moore, T. E.; Lavraud, B.; Strangeway, R. J.; Russell, C. T.; Khotyaintsev, Y. V.; Le Contel, O.; Avanov, L. A.
2016-12-01
Encounters of reconnection diffusion regions by the Magnetospheric Multiscale (MMS) mission during its first magnetopause scan are studied in combination with theories and simulations. The goal is to understand by first-principles how stored magnetic energy is converted into plasma thermal and bulk flow energies via particle energization, mixing and interaction with waves. The magnetosheath population having much higher density than the magnetospheric plasma is an outstanding narrator for and participant in the magnetospheric part of the diffusion region. For reconnection with negligible guide fields, the accelerated magnetosheath population (for both electrons and ions) is cyclotron turned by the reconnected magnetic field to form outflow jets, and then gyrotropized downstream. Wave fluctuations are reduced in the central electron diffusion region (EDR) and do not dominate the energy conversion there. For an event with a significant guide field to magnetize the electrons, wave fluctuations at the lower hybrid frequency dominate the energy conversion in the EDR, and the fastest electron outflow is established dominantly by a strong perpendicular electric field via the ExB flow in one exhaust and by time-of-flight effects along with parallel electric field acceleration in the other. Whether the above features are common threads to magnetopause reconnection diffusion regions is a question to be further examined.
-
Survey of Veterinary Drug Residues in Raw Milk in Hebei Province, China.
Han, Rong-Wei; Yu, Zhong-Na; Zhen, Tian-Yuan; Wang, Jun
2017-10-17
The objective of this study was to investigate the occurrence of veterinary drug residues in raw milk from Hebei, the second-largest dairy production province in the People's Republic of China. A total of 192 raw milk samples were collected from 64 milk stations in seven districts. Twenty-eight veterinary drug residues were analyzed by ultraperformance liquid chromatography with tandem mass spectrometry based on a China National Standard. Raw milk samples with multiple residues of veterinary drugs were not found in the present study. Residues of four veterinary drugs, penicillin G, sulfacetamide, trimethoprim, and lincomycin, were detected in 12 (6.25%) raw milk samples, with detection ratios of 1.04, 0.52, 3.13, and 1.56%, respectively. All veterinary drug residues detected were under the maximum residue levels as regulated by China, the European Union, the United States, and the Codex Alimentarius Commission. In general, raw milk from Hebei province was considered relatively safe for human consumption because of the low prevalence of veterinary drug residues. However, stringent control measurements for veterinary drug residues in raw milk are required because some veterinary drugs were detected in milk from some areas of Hebei province.
-
Aldabsheh, Islam; Garcia-Valles, Maite; Martinez, Salvador
2014-05-01
Environmental preservation has become a driving force behind the search for new sustainable and environmentally friendly composites to replace conventional concrete produced from ordinary Portland cement (OPC). Current researches concentrate on developing building products (geopolymers) through geopolymerization. The goal is to produce low cost construction materials for green housing. Geopolymerization is the process of polymerizing minerals with high silica and alumina at low temperature by the use of alkali solutions. Dissolution is the most important process for supplying the high initial Al and Si concentrations to produce the gel phase that is responsible for geopolymerization. This study has been focused on the influence of different micrometric particle sizes of three Jordanian raw materials on their dissolution behavior in sodium hydroxide solution. The samples are kaolinite, volcanic tuff and silica sand. The dissolution properties of each material, alone and mixed with the other two materials were studied in different concentrations (5 and 10 M) using (NaOH) at 25ºC, and shaking time for 24 and 168 h. To better understand the dissolution process, the alkaline solution was renewed after the desired time in order to know if the Al-Si raw material is completely dissolved or not. Different analytical techniques were used to characterize raw materials physically, mineralogically, chemically and thermally. All processed samples either centrifuged solutions or solid residues were fully characterized. The leached concentrations of Al and Si were determined by inductively coupled plasma (ICP). X-ray Diffraction Technique (XRD), Scanning Electron Microscopy (SEM), and Thermo Gravimetric Analysis (TGA) were used to evaluate the solid residue characterization compared with the original ones. The three aluminosilicate raw materials have indicated variable degrees of solubility under highly alkaline conditions. The method for the size reduction of the used raw
-
Chapter No.6. Radioactive waste (RAW)
International Nuclear Information System (INIS)
2002-01-01
installation 'Technologies for treatment and conditioning of radwaste' consists mainly of two bituminization plants and Bohunice Conditioning Centre (BSC RAW). Bituminization plants with capacity of 120 l/hour each are determined for bituminization of concentrates from VVER type NPPs and from A1 NPP Bohunice which are put into 200 l drums. The first one has been in operation since 1994 and its modification for discontinuous bituminization of ion-exchange resins and sludge is under way. The second one the commissioning of which has been finished successfully is now under licensing process for operation. At the end of 2001 total amount of concentrates treated by bituminization reached 941,7 m3. BSC RAW is the basic installed facility for final radwaste conditioning is. Besides cementation the technologies of incineration, fragmentation, high-pressure compaction as well as evaporation are used for radwaste treatment and conditioning at BSC RAW. Due to a complexity of commissioning of individual technologies, BSC RAW commissioning was divided in two phases which were realised in 2000. At the beginning of 2001 UJD issued the permission for BSC RAW operation on the basis of assessment of commissioning report. 144 pieces of FRC containers have been filled in during BSC RAW operation in 2001. As much as 51 t of solid radwaste and 3,9 m3 of liquid radwaste were incinerated, 85,7 t of solid radwaste were compacted and 186 m3 of concentrates were treated by cementation. Two treatment facilities are operated by VUJE Trnava. The bituminization plant has been out of operation during 2001 and incinerator with additional cementation facility have been used only for experimental purposes. National near surface repository in Mochovce is determined for the disposal of low and intermediate level short-living radwaste in special FRC containers as additional engineering barrier of repository. The repository construction was finished in November 1992. 52 containers with radwaste were disposed of
-
System simulation application for determining the size of daily raw material purchases at PT XY
Napitupulu, H. L.
2018-02-01
Every manufacturing company needs to implement green production, including PT XY as a marine catchment processing industry in Sumatera Utara Province. The company is engaged in the processing of squid for export purposes. The company’s problem relates to the absence of a decision on the daily purchase amount of the squid. The purchase of daily raw materials in varying quantities has caused companies to face the problem of excess raw materials or otherwise the lack of raw materials. The low purchase of raw materials will result in reduced productivity, while large purchases will lead to increased cooling costs for storage of excess raw materials, as well as possible loss of damage raw material. Therefore it is necessary to determine the optimal amount of raw material purchases every day. This can be determined by applying simulation. Application of system simulations can provide the expected optimal amount of raw material purchases.
-
19 CFR 151.23 - Allowance for moisture in raw sugar.
2010-04-01
... 19 Customs Duties 2 2010-04-01 2010-04-01 false Allowance for moisture in raw sugar. 151.23...; DEPARTMENT OF THE TREASURY (CONTINUED) EXAMINATION, SAMPLING, AND TESTING OF MERCHANDISE Sugars, Sirups, and Molasses § 151.23 Allowance for moisture in raw sugar. Inasmuch as the absorption of sea water or moisture...
-
Raw sewage as breeding site to Aedes (Stegomyia) aegypti (Diptera, culicidae).
Chitolina, R F; Anjos, F A; Lima, T S; Castro, E A; Costa-Ribeiro, M C V
2016-12-01
The selection of oviposition sites by females of Aedes (Stegomyia) aegypti is a key factor for the larval survival and egg dispersion and has a direct influence in vector control programs. In this study, we evaluated the aspects of reproductive physiology of Ae. aegypti mosquitoes tested in the presence of raw sewage. Ae. aegypti females were used in oviposition bioassays according to two methodologies: (i) choice assay, in which three oviposition substrates were offered in the same cage: treatment (raw sewage), positive control (distilled water) and negative control (1% sodium hypochlorite) and; (ii) no choice assay, in which only one substrate was available. The physicochemical and microbiological analysis of the raw sewage used in this study indicated virtually no levels of chlorine, low levels of dissolved oxygen and high levels of nitrogenous compounds as well as the presence of Escherichia coli and total fecal coliforms. After 72h of oviposition, the eggs were counted and there was no statistically significant difference (p>0.05) in the oviposition rate between raw sewage and positive control in both methodologies. In addition, females were dissected to evaluate egg-retention and also there were no appreciable differences in egg retention even when raw sewage was the only substrate offered. The data also showed that egg hatching and larvae development occurred normally in the raw sewage. Therefore, the present study suggests that Ae. aegypti can adapt to new sites and lay eggs in polluted water, such as the raw sewage. These findings are of particular importance for the control and surveillance programs against Ae. aegypti in countries where the conditions of poor infrastructure and lack of basic sanitation are still an issue. Copyright © 2016 Elsevier B.V. All rights reserved.
-
Microbial Contamination of Raw Vegetables in Ahvaz, Iran during 2014-2015
Directory of Open Access Journals (Sweden)
Abdol Kazem Neisi
2016-07-01
Full Text Available Background & Aims of the Study: Vegetables are useful for humans as they contain minerals, vitamins, fiber and other nutrients. Eating raw vegetables are a nutritional habit in Iranian families. Raw eating vegetables is the main source of parasitic infections. The aim of this study was to determine microbial contamination of raw vegetables in Ahvaz, Iran during 2014-2015. Materials and Methods: In this study, 20 samples collected from markets of Ahvaz. Average weight of collecting raw vegetables was 1 to 2 kilograms. Then, raw vegetables were washed by 4 to 5 liter tap water. For parasitic ova washed water leaved for 24 hours for sedimentation and then the supernatant poured and about 50 to 100 milliliter of settled water transferred to 15 ml centrifugal tubes. After centrifugation, pellet floated and finally parasitic ova were observed microscopically (corrected Bailenger method. The multiple tube method used for Coliform bacteria (Total & Faecal examination. Results: Maximum Coliform bacteria was in Kootabdullah samples (total Coliform was 25893319.52 MPN/100ml and Fecal Coliform was 15054572.83 MPN/100ml. Maximum Ascaris ova in Hamidieh was 43.3 per liter and Sheiban 36.66 per litter. Conclusion: Microbial contamination of raw vegetables, especially in Kootabdullah, possibly was due to Karoon river water pollution by sewage discharge of Ahvaz city, and also in Hamidieh possibly due to Karkheh river water pollution by sewage discharge of Hamidieh city. Thus, sewage treatment of these cities before discharging in rivers is necessary.
-
A Fast Synthetic Aperture Radar Raw Data Simulation Using Cloud Computing.
Li, Zhixin; Su, Dandan; Zhu, Haijiang; Li, Wei; Zhang, Fan; Li, Ruirui
2017-01-08
Synthetic Aperture Radar (SAR) raw data simulation is a fundamental problem in radar system design and imaging algorithm research. The growth of surveying swath and resolution results in a significant increase in data volume and simulation period, which can be considered to be a comprehensive data intensive and computing intensive issue. Although several high performance computing (HPC) methods have demonstrated their potential for accelerating simulation, the input/output (I/O) bottleneck of huge raw data has not been eased. In this paper, we propose a cloud computing based SAR raw data simulation algorithm, which employs the MapReduce model to accelerate the raw data computing and the Hadoop distributed file system (HDFS) for fast I/O access. The MapReduce model is designed for the irregular parallel accumulation of raw data simulation, which greatly reduces the parallel efficiency of graphics processing unit (GPU) based simulation methods. In addition, three kinds of optimization strategies are put forward from the aspects of programming model, HDFS configuration and scheduling. The experimental results show that the cloud computing based algorithm achieves 4_ speedup over the baseline serial approach in an 8-node cloud environment, and each optimization strategy can improve about 20%. This work proves that the proposed cloud algorithm is capable of solving the computing intensive and data intensive issues in SAR raw data simulation, and is easily extended to large scale computing to achieve higher acceleration.
-
Advanced tertiary treatment of municipal wastewater using raw and modified diatomite.
Wu, Jinlu; Yang, Y S; Lin, Jinhua
2005-12-09
Advanced technology for more efficient and effective wastewater treatment is always timely needed. The feasibility of using raw and modified diatomite for advanced treatment of secondary sewage effluents (SSE) was investigated in this study. Raw diatomite at a dosing rate of 300 mg/l showed a similar potential as activated carbon for removing most organic pollutants and toxic metals from SSE. Its performance was found poor in removal of arsenic and crop nutrient constituents (e.g. ammoniacal nitrogen and phosphate) and remained unsatisfactory even when the dosing rate increased up to 500 mg/l. Where modified diatomite was in lieu of raw diatomite, the removal efficiency for all target constituents was improved by 20-50%. At the dosing rate of 150 mg/l, modified diatomite enabled the post-treated effluents to satisfy the discharge consents, with the levels of all target constituents below the regulatory limits. Modified diatomite has advantages over raw diatomite in improving removal efficiency and reducing the dosing rate required for satisfactory treatment of SSE. It is concluded that modified diatomite is much more effective and efficient than raw diatomite, as an alternative to activated carbon, for economic treatment of SSE.
-
Method for online measurement of the CHON composition of raw gas from biomass gasifier
International Nuclear Information System (INIS)
Neves, Daniel; Thunman, Henrik; Tarelho, Luís; Larsson, Anton; Seemann, Martin; Matos, Arlindo
2014-01-01
Highlights: • Measuring the CHON composition of a raw gas by current methods is challenging. • An alternative method is to burn the raw gas before measuring the CHON composition. • The CHON contents of the raw gas can be accurately measured by the alternative method. • Measuring the CHON contents of the raw gas is now performed in a “one-step” analysis. • The new method is used to evaluate the operation of a dual fluidised bed gasifier. - Abstract: For unattended biomass gasification processes, rapid methods for monitoring the elemental composition (CHON) of the raw gas leaving the gasifier are needed. Conventional methods rely on time-consuming and costly laboratory procedures for analysing the condensable part of the raw gas. An alternative method, presented in this work, assesses the CHON composition of raw gas in a “one step” analysis without the need to previously characterise its chemical species composition. Our method is based on the quantitative conversion of a raw gas of complex chemical composition into CO 2 , H 2 O, and N 2 in a small combustor. The levels of these simple species can be measured with high accuracy and good time resolution, and the CHON composition of the raw gas can be determined from the mass balance across the combustor. To evaluate this method, an online combustion facility was built and used to analyse the raw gas from the Chalmers 2-MW th dual fluidised bed steam gasifier. Test runs of the developed facility demonstrated complete combustion of the raw gas and the measurements were both fast and reliable. The new method used in combination with zero-dimensional reactor modelling provides valuable data for the operational monitoring of gasification processes, such as the degree of fuel conversion, composition of the char exiting the gasifier, oxygen transport by catalytic bed material, and amount of condensables in raw gas
-
Topical papers on raw materials
International Nuclear Information System (INIS)
1978-01-01
In the papers of this working group, the availability of uranium and the long-term supply situation for this raw material are discussed. A problem closely connected with uranium supply are the commercial contracts and their particularities. The points of view of the reporting countries of Great Britain, South Africa, Switzerland, Australia, Japan, and Korea are made clear
-
40 CFR 63.1343 - Standards for kilns and in-line kiln/raw mills.
2010-07-01
.../raw mills. 63.1343 Section 63.1343 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Industry Emission Standards and Operating Limits § 63.1343 Standards for kilns and in-line kiln/raw mills. (a) General. The provisions in this section apply to each kiln, each in-line kiln/raw mill, and any...
-
Annual report 2005 General Direction of the Energy and raw materials
International Nuclear Information System (INIS)
2005-01-01
This 2005 annual report of the DGEMP (General Direction of the Energy and the raw Materials), takes stock on the energy bill and accounting of the France. The first part presents the electric power, natural gas and raw materials market in France. The second part is devoted to the diversification of the energy resources with a special attention to the renewable energies and the nuclear energy. The third part discusses the energy and raw materials prices and the last part presents the international cooperation in the energy domain. (A.L.B.)
-
Monitoring of psychrotrophic microorganisms in raw milk
Directory of Open Access Journals (Sweden)
Radka Burdychová
2008-01-01
Full Text Available The group of psychrotrophic microorganisms belongs to the microorganisms representing a risk for human health as well as a risk of milk and milk products spoilage. Some genus are considered to be significant producers of proteolytic and lipolytic enzymes. In this work, we analysed raw milk samples (n = 109 originated from 26 different suppliers from the area of North and Middle Moravia. The screening was performed from March 2007 to February 2008. The total bacterial counts (TBC ranged between 3.2 × 103 to 8.3 × 106 CFU/ml. The psychrotrophic bacterial counts (PBC ranged between 1.0 × 103 to 8.2 × 106 CFU/ml. Total of 48.62 % and 48.62 % of samples exceeded the hygienic limit in raw milk for TBC and PBC, respectively. The correlation between TBC and PBC was highly significant (r = 0.87.Significantly higher (P < 0.05 numbers of psychrotrophic microorganisms were detected in summer months. The identification of isolates was carried out and all strains were sreened for ability to produce proteolytic and lipolytic enzymes. The most commonly identified genus in raw milk was of the genus Pseudomonas. The ability to produce proteases or lipases was found at 76 % identified bacterial strains.
-
Colonna, A; Durham, C; Meunier-Goddik, L
2011-10-01
Eight hundred ninety consumers at a local food festival were surveyed about their specialty cheese purchasing behavior and asked to taste and rate, through nonforced choice preference, 1 of 4 cheese pairs (Cheddar and Gouda) made from pasteurized and raw milks. The purpose of the survey was to examine consumers' responses to information on the safety of raw milk cheeses. The associated consumer test provided information about specialty cheese consumers' preferences and purchasing behavior. Half of the consumers tested were provided with cheese pairs that were identified as being made from unpasteurized and pasteurized milk. The other half evaluated samples that were identified only with random 3-digit codes. Overall, more consumers preferred the raw milk cheeses than the pasteurized milk cheeses. A larger portion of consumers indicated preferences for the raw milk cheese when the cheeses were labeled and thus they knew which samples were made from raw milk. Most of the consumers tested considered the raw milk cheeses to be less safe or did not know if raw milk cheeses were less safe. After being informed that the raw milk cheeses were produced by a process approved by the FDA (i.e., 60-d ripening), most consumers with concerns stated that they believed raw milk cheeses to be safe. When marketing cheese made from raw milk, producers should inform consumers that raw milk cheese is produced by an FDA-approved process. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.
-
Identification of species adulteration in traded medicinal plant raw drugs using DNA barcoding.
Nithaniyal, Stalin; Vassou, Sophie Lorraine; Poovitha, Sundar; Raju, Balaji; Parani, Madasamy
2017-02-01
Plants are the major source of therapeutic ingredients in complementary and alternative medicine (CAM). However, species adulteration in traded medicinal plant raw drugs threatens the reliability and safety of CAM. Since morphological features of medicinal plants are often not intact in the raw drugs, DNA barcoding was employed for species identification. Adulteration in 112 traded raw drugs was tested after creating a reference DNA barcode library consisting of 1452 rbcL and matK barcodes from 521 medicinal plant species. Species resolution of this library was 74.4%, 90.2%, and 93.0% for rbcL, matK, and rbcL + matK, respectively. DNA barcoding revealed adulteration in about 20% of the raw drugs, and at least 6% of them were derived from plants with completely different medicinal or toxic properties. Raw drugs in the form of dried roots, powders, and whole plants were found to be more prone to adulteration than rhizomes, fruits, and seeds. Morphological resemblance, co-occurrence, mislabeling, confusing vernacular names, and unauthorized or fraudulent substitutions might have contributed to species adulteration in the raw drugs. Therefore, this library can be routinely used to authenticate traded raw drugs for the benefit of all stakeholders: traders, consumers, and regulatory agencies.
-
Chances for a long-term securing of the raw material supply to the FRG. Pt. 1
International Nuclear Information System (INIS)
1975-09-01
The Federal Republic of Germany is almost completely dependent on raw material imports. Growing raw material consumption and an imminent increase in supply uncertainties will require intensified research and development work in the field of raw material safeguarding. Initial approaches to possible technical solutions are being indicated in connection with four raw materials (aluminium, copper, phosphate and carbon carriers). The material balances of these raw materials are shown and the technical and economic interrelations illustrated in the light of world-wide trends. It is being demonstrated that two essential objectives are to be pursued for securing raw material supplies: 1) extension of the raw material basis for primary and secondary raw materials, 2) improvement of raw material utilization in all sectors of economy. To provide a solution for the wide spectrum of tasks it will be necessary to establish adequate analytical methods and procedures. (orig.) [de
-
The Formulation of Binding Agent Concentration on Raw Restructured Goat Meat Trimming Product
Directory of Open Access Journals (Sweden)
Rini Mastuti
2012-02-01
Full Text Available The utilization of raw materials and formulation method would affect the quality of the processed meat product. Therefore, a research on the processing method to produce a raw structured product should be conducted. The research was testing a single factor comprises of following parameters: control (without binding agent; 0.3%, 0.5% and 0.7% sodium alginat and 0.3%, 0.5% and 0.7% carragenan, respectively. The results showed that the goat meat trimming could be used as raw materials in the production of the best restructured meat using 0.5% carragenan. This raw restructured meat produced had a loss weight of 1.67%, pH value 7.89, WHC 48.345, and moisture content 75.20%. Keywords : sodium alginat, carragenan, raw restructured goat meat trimming.
-
Investigation of ceramic devices by analytical electron microscopy techniques
International Nuclear Information System (INIS)
Shiojiri, M.; Saijo, H.; Isshiki, T.; Kawasaki, M.; Yoshioka, T.; Sato, S.; Nomura, T.
1999-01-01
Ceramics are widely used as capacitors and varistors. Their electrical properties depend on the structure, which is deeply influenced not only by the composition of raw materials and additives but also by heating treatments in the production process. This paper reviews our investigations of SrTiO 3 ceramic devices, which have been performed using various microscopy techniques such as high-resolution transmission electron microscopy (HRTEM), cathodoluminescence scanning electron microscopy (CLSEM), field emission SEM (FE-SEM), energy dispersive X-ray spectroscopy (EDS), electron energy-loss spectroscopy (EELS) and high angle annular dark field (HAADF) imaging method in a FE-(scanning) transmission electron microscope(FE-(S)TEM). (author)
-
Pulse current enhanced electrodialytic soil remediation
DEFF Research Database (Denmark)
Sun, Tian R.; Ottosen, Lisbeth M.; Jensen, Pernille E.
2012-01-01
Energy consumption is an important factor influencing the cost of electrodialytic soil remediation (EDR). It has been indicated that the pulse current (in low frequency range) could decrease the energy consumption during EDR. This work is focused on the comparison of energy saving effect at diffe......Energy consumption is an important factor influencing the cost of electrodialytic soil remediation (EDR). It has been indicated that the pulse current (in low frequency range) could decrease the energy consumption during EDR. This work is focused on the comparison of energy saving effect...
-
National Aeronautics and Space Administration — This data set contains raw laser altimeter, Inertial Measurement Unit (IMU), Global Positioning System (GPS), and camera data over Greenland and Antarctica taken...
-
National Aeronautics and Space Administration — This data set contains raw laser altimeter, Inertial Measurement Unit (IMU), Global Positioning System (GPS), and camera data over Greenland, Antarctica, and Alaska...
-
Monitoring of foodborne pathogens in raw cow milk in Tuscany
Directory of Open Access Journals (Sweden)
Laura Gasperetti
2014-03-01
Full Text Available Raw milk consumption in Italy has increased over the last few years and although raw milk is characterised by cold chain, short shelf-life and the duty of boiling before domestic consumption, it is still considered a hazard. From 2010 to 2013 a monitoring survey of raw milk sold through vending machines was carried out to investigate the occurrence of several foodborne pathogens stipulated in the national legal requirements, i.e. Listeria monocytogenes, Campylobacter spp., Salmonella spp., Escherichia coli O:157 and coagulase-positive Staphylococci. A total of 127 raw milk samples were collected from 19 dairy herds in Tuscany Region, Italy. In addition, the milk samples were tested for the presence and count of Yersinia genus. Results shown that only one sample was positive for non verocytotoxin- producing E. coli O:157, whereas a total of 38 samples (29.9% were postive for Yersinia genus; of the total 39 isolated bacteria, 23.6% were Y. enterocolitica, 2.4% Y. kristenseni and 4.7% Y. frederiksenii. None isolate was enteropathogenic; serotypes O:5 and O:8 were found in 16.6 and 13.3% of the isolates respectively, whereas none of the serotypes tested was detected in 70% of the isolates. The most probable number method revealed a count value between 0.03 and 24 MPN/mL. Based on these data a general assurance on health safety of raw milk produced and sold in Tuscany could be assessed.
-
DEFF Research Database (Denmark)
Bach, Vibe; Kidmose, Ulla; Thybo, Anette
2013-01-01
BACKGROUND: The aim of the present study was to investigate the sensory attributes, dry matter and sugar content of five varieties of Jerusalem artichoke tubers and their relation to the appropriateness of the tubers for raw and boiled preparation. RESULTS: Sensory evaluation of raw and boiled...... Jerusalem artichoke tubers was performed by a trained sensory panel and a semi-trained consumer panel of 49 participants, who also evaluated the appropriateness of the tubers for raw and boiled preparation. The appropriateness of raw Jerusalem artichoke tubers was related to Jerusalem artichoke flavour...... attributes can be used as predictors of the appropriateness of Jerusalem artichoke tubers for raw and boiled consumption. Knowledge on the quality of raw and boiled Jerusalem artichoke tubers can be used to inform consumers on the right choice of rawmaterial and thereby increase the consumption...
-
Operating results of Kosmos Cement's O-SEPA separator for raw grinding
Energy Technology Data Exchange (ETDEWEB)
Ireland, T C [Consultec Ltd., Toronto (CA); Schultz, G K [Southdown Incorporated, Houston, TX (US)
1991-01-01
High efficiency separators were first introduced in the cement industry to improve the energy efficiency of finish grinding circuits. Lately, however, a great deal of interest has been focused on improving the energy efficiency of raw grinding circuits. High efficiency separators have successfully been installed in roller mills as well as in ball mill raw grinding circuits. This paper describes the operating experience of the first installation in North America using a high efficiency separator in a raw grinding circuit. This installation, commissioned in 1988 at the Louisville, Kentucky plant of Kosmos Cement, uses a conventional 4500 HP ball mill and a high efficiency dynamic separator to produce raw meal for a preheater kiln as well as high fineness limestone for sulphur scrubbing in a nearby power plant. The system uses kiln exhaust gases for drying both in the mill and in the separator. (author).
-
Natural gas as raw material for industrial development
International Nuclear Information System (INIS)
Kvisle, Steinar
2006-01-01
Industrial development based on natural gas has broad, industrial implications. Norway has a vital industry based on natural gas as raw material, here under Ormen Lange, Snoehvit LNG, Tjeldbergodden and Petrochemical Grenland. The petrochemical industry has challenges, e.g. the cost of raw materials and energy, localization related to the markets, and recruitment, but considerable investments are made in the sector. The Northern areas in Norway may have special challenges related to bringing the product to the market. Solutions to this challenge are in LNG (liquid natural gas), GTL (gas to liquids), and GTO (gas to olefins)
-
PROCESS DEVELOPMENT FOR THE RECOVERY OF CRITICAL MATERIALS FROM ELECTRONIC WASTE
Energy Technology Data Exchange (ETDEWEB)
Lister, T. E.; Diaz, L. A.; Clark, G. G.; Keller, P.
2016-09-01
As electronic technology continues to evolve there is a growing need to develop processes which recover valuable material from antiquated technology. This need follows from the environmental challenges associated with the availability of raw materials and fast growing generation of electronic waste. Although just present in small quantities in electronic devices, the availability of raw materials, such as rare earths and precious metals, becomes critical for the production of high tech electronic devices and the development of green technologies (i.e. wind turbines, electric motors, and solar panels). Therefore, the proper recycling and processing of increasing volumes of electronic waste present an opportunity to stabilize the market of critical materials, reducing the demand of mined products, and providing a proper disposal and treatment of a hazardous waste stream. This paper will describe development and techno-economic assessment of a comprehensive process for the recovery of value and critical materials from electronic waste. This hydrometallurgical scheme aims to selectively recover different value segments in the materials streams (base metals, precious metals, and rare earths). The economic feasibility for the recovery of rare earths from electronic waste is mostly driven by the efficient recovery of precious metals, such as Au and Pd (ca. 80 % of the total recoverable value). Rare earth elements contained in magnets (speakers, vibrators and hard disk storage) can be recovered as a mixture of rare earths oxides which can later be reduced to the production of new magnets.
-
Determination of Heavy Metals in Raw Milk Produced in Tangshan City, China
Directory of Open Access Journals (Sweden)
Li Aijun
2016-01-01
Full Text Available The objective of this study was to investigate the content of heavy metals (Arsenic, Lead, Chromium and Mercury in raw milk of Tangshan. Samples were obtained directly from dairy farms in Tangshan City. A total of 55 raw milk samples were collected in 2012, a total of 150 raw milk samples and 150 in 2013 and 2014 respectively. All the samples were analyzed by ICP-MS (Inductively Coupled Plasma Mass Spectrometry method-based on China National Standard. In general, heavy metals (Arsenic, Lead, Chromium and Mercury of raw milk in Tangshan were relatively safe for people’s health because none of those heavy metals (Arsenic, Lead, Chromium and Mercury contents exceeded the Maximum Limit set by China.
-
Stability of vitamin C in frozen raw fruit and vegetable homogenates
Retention of vitamin C in homogenized raw fruits and vegetables stored under laboratory conditions prior to analysis was investigated. Raw collard greens, clementines, and potatoes were chosen, to be representative of food matrices to be sampled in USDA’s National Food and Nutrient Analysis Program...
-
Optimization of the Clarification System for Raw Water from the Pakra Reservoir Lake
Directory of Open Access Journals (Sweden)
Zečević, N.
2011-10-01
Full Text Available The first step in processing raw water from the Pakra lake for use in fertilizer production at Petrokemija is oxidation of total organic carbon matter with gaseous chlorine, Cl2. Thereupon it is clarified and filtered with the help of a clarification reactor and sand filters. Construction of the clarification reactor and process sand filters enables only the removal of the suspended matter from the raw water, without affecting its overall hardness. Process control of the clarification reactor and removal of the suspended matter from the raw water is achieved by adding corresponding mass concentration water solutions of aluminum sulphate, Al2(SO43 · 18 H2O and organic polyelectrolyte. The effectiveness of flocculation is carried out by laboratory determination of the m-alkalinity difference between inlet and outlet of raw water from the clarification reactor. For the most effective clarification of raw water, the optimal empirical value of the m-alkalinity difference is 0.65 mmol L-1 in the pH range of raw water from 7.0 to 8.0. Prior to processing clarified water by ionic decarbonatisation and demineralisation for protection of the ionic exchange resin from excess free Cl2, a corresponding mass concentration of a sodium bisulfite water solution, NaHSO3, is added. An improved system is proposed for continuous measurement of mass concentrations of free Cl2 in raw and clarified water, and pH difference value at the inlet and outlet of the clarification reactor. The proposed system can achieve optimal dosage of gaseous Cl2 in the raw water, improving the clarification process in the reactor as well as optimal dosage of water solution of NaHSO3. It is shown that the average pH difference from 0.65 to 0.75 at the inlet and outlet of the clarification reactor in the pH range of the raw water from 7.0 to 8.0 is an equally effective replacement for the laboratory determination of m-alkalinity. Also shown is the connection between dosage mass of the
-
Lipid analyses of fumigated vs irradiated raw and roasted almonds
International Nuclear Information System (INIS)
Uthman, R.S.; Toma, R.B.; Garcia, R.; Medora, N.P.; Cunningham, S.
1998-01-01
The purpose of this study was to compare the effects of propylene oxide (PO) and irradiation treatments on the lipid analyses of raw and roasted almonds. Eight kilograms each of raw and roasted almonds were divided into four batches (2 kg each). Three of the batches were subjected to PO treatment or irradiation treatment with a dose of 6, 10·5 kGy. The untreated batch served as control samples, they were taken from all the batches at three consecutive times during storage (day 0, 8 weeks and 16 weeks) and analysed for iodine number, peroxide value and 2-thiobarbituric acid number. Overall, irradiated almonds incurred a higher variation in lipid stability than PO tested almonds while roasted almonds incurred a higher variation than raw almonds
-
Mian, Muhammad Oneeb Rehman; Idris-Khodja, Noureddine; Li, Melissa W; Leibowitz, Avshalom; Paradis, Pierre; Rautureau, Yohann; Schiffrin, Ernesto L
2013-10-01
In human atherosclerosis, which is associated with elevated plasma and coronary endothelin (ET)-1 levels, ETA receptor antagonists improve coronary endothelial function. Mice overexpressing ET-1 specifically in the endothelium (eET-1) crossed with atherosclerosis-prone apolipoprotein E knockout mice (Apoe(-/-)) exhibit exaggerated high-fat diet (HFD)-induced atherosclerosis. Since endothelial dysfunction often precedes atherosclerosis development, we hypothesized that mice overexpressing endothelial ET-1 on a genetic background deficient in apolipoprotein E (eET-1/Apoe(-/-)) would have severe endothelial dysfunction. To test this hypothesis, we investigated endothelium-dependent relaxation (EDR) to acetylcholine in eET-1/Apoe(-/-) mice. EDR in mesenteric resistance arteries from 8- and 16-week-old mice fed a normal diet or HFD was improved in eET-1/Apoe(-/-) compared with Apoe(-/-) mice. Nitric oxide synthase (NOS) inhibition abolished EDR in Apoe(-/-). EDR in eET-1/Apoe(-/-) mice was resistant to NOS inhibition irrespective of age or diet. Inhibition of cyclooxygenase, the cytochrome P450 pathway, and endothelium-dependent hyperpolarization (EDH) resulted in little or no inhibition of EDR in eET-1/Apoe(-/-) compared with wild-type (WT) mice. In eET-1/Apoe(-/-) mice, blocking of EDH or soluble guanylate cyclase (sGC), in addition to NOS inhibition, decreased EDR by 36 and 30%, respectively. The activation of 4-aminopyridine-sensitive voltage-dependent potassium channels (Kv) during EDR was increased in eET-1/Apoe(-/-) compared with WT mice. We conclude that increasing eET-1 in mice that develop atherosclerosis results in decreased mutual dependence of endothelial signaling pathways responsible for EDR, and that NOS-independent activation of sGC and increased activation of Kv are responsible for enhanced EDR in this model of atherosclerosis associated with elevated endothelial and circulating ET-1.
-
Effect of Raw Crushed Garlic (Allium sativum L.) on Components of Metabolic Syndrome.
Choudhary, Prema Ram; Jani, Rameshchandra D; Sharma, Megh Shyam
2017-09-28
Metabolic syndrome consists of a group of risk factors characterized by abdominal obesity, hypertension, atherogenic dyslipidemia, hyperglycemia, and prothrombotic and proinflammatory conditions. Raw garlic homogenate has been reported to reduce serum lipid levels in animal model; however, no precise studies have been performed to evaluate the effect of raw crushed garlic (Allium sativum L.) on components of metabolic syndrome. Therefore, the present study was designed to investigate the effect of raw crushed garlic on components of metabolic syndrome. A total of 40 metabolic syndrome patients were randomly selected from the diabetic center of SP Medical College, Bikaner, Rajasthan, India. They underwent treatment with 100 mg/kg body weight raw crushed garlic 2 times a day with standard diet for 4 weeks; their anthropometric and serum biochemical variables were measured at both the beginning and the end of the study. Statistical analysis was performed using IBM SPSS version 20, and Student's paired "t" test was used to compare variables before and after treatment with garlic preparation. Raw crushed garlic significantly reduced components of metabolic syndrome including waist circumference (p .05) of patients with metabolic syndrome after consumption of raw crushed garlic for 4 weeks. Raw crushed garlic has beneficial effects on components of metabolic syndrome; therefore, it can be used as an accompanying remedy for prevention and treatment of patients with metabolic syndrome.
-
Bacterial lipopolysaccharide induces osteoclast formation in RAW 264.7 macrophage cells
International Nuclear Information System (INIS)
Islam, Shamima; Hassan, Ferdaus; Tumurkhuu, Gantsetseg; Dagvadorj, Jargalsaikhan; Koide, Naoki; Naiki, Yoshikazu; Mori, Isamu; Yoshida, Tomoaki; Yokochi, Takashi
2007-01-01
Lipopolysaccharide (LPS) is a potent bone resorbing factor. The effect of LPS on osteoclast formation was examined by using murine RAW 264.7 macrophage cells. LPS-induced the formation of multinucleated giant cells (MGC) in RAW 264.7 cells 3 days after the exposure. MGCs were positive for tartrate-resistant acid phosphatase (TRAP) activity. Further, MGC formed resorption pits on calcium-phosphate thin film that is a substrate for osteoclasts. Therefore, LPS was suggested to induce osteoclast formation in RAW 264.7 cells. LPS-induced osteoclast formation was abolished by anti-tumor necrosis factor (TNF)-α antibody, but not antibodies to macrophage-colony stimulating factor (M-CSF) and receptor activator of nuclear factor (NF)-κB ligand (RANKL). TNF-α might play a critical role in LPS-induced osteoclast formation in RAW 264.7 cells. Inhibitors of NF-κB and stress activated protein kinase (SAPK/JNK) prevented the LPS-induced osteoclast formation. The detailed mechanism of LPS-induced osteoclast formation is discussed
-
File list: Oth.Bld.05.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available Oth.Bld.05.AllAg.RAW_264PERIOD7 mm9 TFs and others Blood RAW 264.7 SRX218749,SRX147...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/Oth.Bld.05.AllAg.RAW_264PERIOD7.bed ...
-
File list: Oth.Bld.10.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available Oth.Bld.10.AllAg.RAW_264PERIOD7 mm9 TFs and others Blood RAW 264.7 SRX264595,SRX026...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/Oth.Bld.10.AllAg.RAW_264PERIOD7.bed ...
-
File list: DNS.Bld.20.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available DNS.Bld.20.AllAg.RAW_264PERIOD7 mm9 DNase-seq Blood RAW 264.7 SRX434625,SRX434626 h...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/DNS.Bld.20.AllAg.RAW_264PERIOD7.bed ...
-
File list: DNS.Bld.50.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available DNS.Bld.50.AllAg.RAW_264PERIOD7 mm9 DNase-seq Blood RAW 264.7 SRX434626,SRX434625 h...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/DNS.Bld.50.AllAg.RAW_264PERIOD7.bed ...
-
File list: DNS.Bld.10.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available DNS.Bld.10.AllAg.RAW_264PERIOD7 mm9 DNase-seq Blood RAW 264.7 SRX434626,SRX434625 h...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/DNS.Bld.10.AllAg.RAW_264PERIOD7.bed ...
-
File list: Oth.Bld.20.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available Oth.Bld.20.AllAg.RAW_264PERIOD7 mm9 TFs and others Blood RAW 264.7 SRX264595,SRX147...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/Oth.Bld.20.AllAg.RAW_264PERIOD7.bed ...
-
File list: Oth.Bld.50.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available Oth.Bld.50.AllAg.RAW_264PERIOD7 mm9 TFs and others Blood RAW 264.7 SRX1471835,SRX21...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/Oth.Bld.50.AllAg.RAW_264PERIOD7.bed ...
-
File list: DNS.Bld.05.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available DNS.Bld.05.AllAg.RAW_264PERIOD7 mm9 DNase-seq Blood RAW 264.7 SRX434625,SRX434626 h...ttp://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/DNS.Bld.05.AllAg.RAW_264PERIOD7.bed ...
-
Influence of Skin Packaging on Raw Beef Quality: A Review
Directory of Open Access Journals (Sweden)
S. Stella
2018-01-01
Full Text Available A detailed revision of several aspects related to the application of skin packaging to raw beef was considered. Skin packaging, a relatively new technique derived from vacuum packaging, was developed with the aim of retailing small portions of fresh meat, minced meat, or meat preparations. Above all, the influence of this typology of packaging on the microbial population of raw meat was studied, with particular attention to total viable count, aerobic spoilage bacteria, anaerobic bacteria, Enterobacteriaceae, Brochothrix thermosphacta, and lactic acid bacteria. Moreover, the effect on acidification by LAB was also deepened. As colour is the main characteristic influencing purchase decisions at the point of sale, the effect of skin packaging on this parameter was evaluated for raw meat but also for cooked meat. Tenderness, juiciness, and the ability to hold liquid of raw meat when packed in skin conditions were also considered. Furthermore, odour and flavour were considered as sensorial parameters possibly affected by skin packaging. Finally, acceptability by consumer was also investigated. In the studies considered, results showed that skin packaging is advantageous in terms of maintenance of meat quality and for prolonging shelf-life, improving the stability of the products.
-
Design and analysis of fuel ethanol production from raw glycerol
International Nuclear Information System (INIS)
Posada, J.A.; Cardona, C.A.
2010-01-01
Three configurations for fuel ethanol production from raw glycerol using Escherichia coli were simulated and economically assessed using Aspen Plus and Aspen Icarus, respectively. These assessments considered raw glycerol (60 wt%) purification to both crude glycerol (88 wt%) and pure glycerol (98 wt%). The highest purification cost (PC) was obtained using pure glycerol due to its higher energy consumption in the distillation stage. In addition, the remaining methanol in the raw glycerol stream was recovered and recycled, decreasing the purification costs. The E. coli strain is able to convert crude glycerol (at 10 g/L or 20 g/L), or pure glycerol (at 10 g/L) to ethanol. Among these three glycerol concentrations, the lowest bioconversion cost was obtained when crude glycerol was diluted at 20 g/L. Purification and global production costs were compared with the commercial prices of glycerol and fuel ethanol from corn and sugarcane. Purification costs of raw glycerol were lower than previously reported values due to the methanol recovery. Global production costs for fuel ethanol from glycerol were lower than the reported values for corn-based production and higher than those for cane-based production. (author)
-
Basic Thermal Parameters of Selected Foods and Food Raw Materials
Directory of Open Access Journals (Sweden)
Monika Božiková
2017-01-01
Full Text Available In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of thermal parameters measurement for various foods and food raw materials as: granular materials – corn flour and wheat flour; fruits, vegetables and fruit products – grated apple, dried apple and apple juice; liquid materials – milk, beer etc. Measurements were performed in two temperature ranges according to the character of examined material. From graphical relations of thermophysical parameter is evident, that thermal conductivity and diffusivity increases with temperature and moisture content linearly, only for granular materials were obtained non‑linear dependencies. Results shows, that foods and food raw materials have different thermal properties, which are influenced by their type, structure, chemical and physical properties. From presented results is evident, that basic thermal parameters are important for material quality detection in food industry.
-
Improving the Technology of Obtaining Technical Ethanol from Alternative Raw Materials
Directory of Open Access Journals (Sweden)
Sergіj Petrov
2018-05-01
Full Text Available The purpose of the article is to study the properties of fallen leaves as raw materials for the production of bioethanol; Improvement of the technology of recycling cellulosic raw materials into bioethanol in the most energy-efficient and ecological way. As a result of the study, it has been found out that the production of biofuels from renewable raw materials is characterized by features of innovative technology: the rapid growth of this sector of economy is accompanied by a significant increase in market share. The use of fallen leaves as raw material will eliminate the current conflict of interests associated with the use of food raw materials for the production of bioethanol, will prevent the withdrawal of resources from the sphere of food production. Significant positive factors in the production and use of biofuels are improvement of environmental conditions, reduction of the harmful effects of exhaust gases on the human body, reducing environmental pollution and, consequently, reducing morbidity and associated costs of medical care. The use of bioethanol as an ecobiopilot makes it possible to increase the octane number of fuel, and, accordingly, increase the efficiency of the engine. Thus, the use of bioethanol leads to a qualitative improvement of technical and economic indicators, which is also an indicator of innovation. The threat of reducing (exhausting non-renewable sources of energy is also the factor that necessitates the development and improvement of biofuel production technology. The relatively low profitability of biofuel production is due to the low yield of the target product and the high cost of pre-treatment of cellulose raw materials. The method of obtaining bioethanol from renewable non-demanded raw materials - fallen leaves - was improved. The technique allows to increase the bioethanol yield due to more effective hydrolysis of hard-hydrolysable polysaccharides. Further development of the study of the differences in
-
Bach, Vibe; Kidmose, Ulla; Thybo, Anette K; Edelenbos, Merete
2013-03-30
The aim of the present study was to investigate the sensory attributes, dry matter and sugar content of five varieties of Jerusalem artichoke tubers and their relation to the appropriateness of the tubers for raw and boiled preparation. Sensory evaluation of raw and boiled Jerusalem artichoke tubers was performed by a trained sensory panel and a semi-trained consumer panel of 49 participants, who also evaluated the appropriateness of the tubers for raw and boiled preparation. The appropriateness of raw Jerusalem artichoke tubers was related to Jerusalem artichoke flavour, green nut flavour, sweetness and colour intensity, whereas the appropriateness of boiled tubers was related to celeriac aroma, sweet aroma, sweetness and colour intensity. In both preparations the variety Dwarf stood out from the others by being the least appropriate tuber. A few sensory attributes can be used as predictors of the appropriateness of Jerusalem artichoke tubers for raw and boiled consumption. Knowledge on the quality of raw and boiled Jerusalem artichoke tubers can be used to inform consumers on the right choice of raw material and thereby increase the consumption of the vegetable. © 2012 Society of Chemical Industry.
-
Study of chemisrty and hydrolysates drying parameters of feather-downy raw material
LISITSYN A.B.; KRIGER O.V.; MITROKHIN P.V.
2016-01-01
The article describes chemical and amino acid composition of feather-downy raw material. It determines the mass fraction of crude protein, crude fiber, ash, calcium, phosphorus, sodium in the samples of feather-downy raw material. It is stated that the waste from poultry processing obtained from hens of all the studied species are characterized by a high content of crude protein and low in crude fiber and ash. The most valuable feather-downy raw material regarding protein is waste containing ...
-
Map of critical raw material deposits in Europe
Guillaume, Bertrand
2016-04-01
Map of critical raw material deposits in Europe Guillaume BERTRAND1, Daniel CASSARD1, Nikolaos ARVANITIDIS2, Gerry STANLEY3 and the EuroGeoSurvey Mineral Resources Expert Group4. 1 - Bureau de Recherches Géologiques et Minières (BRGM), Georesources Divison, 3 avenue Claude Guillemin, 45060 Orléans cedex 2, FRANCE. 2 - Sveriges Geologiska Undersökning (SGU), Box 670, SE-751 28, Uppsala, SWEDEN 3 - Geological Survey of Ireland (GSI), Beggars Bush, Haddington Road, Dublin D04 K7X4, IRELAND 4 - EuroGeoSurveys, Rue Joseph II 36-38, 1000 Brussels, BELGIUM The Critical Raw Material (CRM) Deposit Map of Europe, prepared by EuroGeoSurvey's Mineral Resources Expert Group (MREG), shows European mineral deposits from the ProMine Mineral Deposit database containing critical commodities, according to the 2014 list of critical raw materials of the European Commission. EuroGeoSurveys (EGS), The Geological Surveys of Europe, is a not-for-profit organization representing 37 National Geological Surveys and some regional Geological Surveys in Europe. It provides the European Institutions with expert, independent, balanced and practical pan-European advice and information as an aid to problem-solving, policy development, regulatory and programme formulation in areas such as natural resources, energy and geo-hazards. The EGS MREG is actively involved in contributing to policy and strategy-making processes aimed at identifying, characterizing and safeguarding resource potential, especially for critical raw materials through data provision, research, technological development and innovation. The European Union aspires to reducing the import dependency of raw materials, especially CRM, that are essential to Europe's industries. In this respect, mineral resource information, data sharing and networking by European Geological Surveys is crucial. The Strategic Implementation Plan of the European Innovation Partnership on Raw Materials highlights the need for establishing and maintaining a
-
Direct hydrodeoxygenation of raw woody biomass into liquid alkanes.
Xia, Qineng; Chen, Zongjia; Shao, Yi; Gong, Xueqing; Wang, Haifeng; Liu, Xiaohui; Parker, Stewart F; Han, Xue; Yang, Sihai; Wang, Yanqin
2016-03-30
Being the only sustainable source of organic carbon, biomass is playing an ever-increasingly important role in our energy landscape. The conversion of renewable lignocellulosic biomass into liquid fuels is particularly attractive but extremely challenging due to the inertness and complexity of lignocellulose. Here we describe the direct hydrodeoxygenation of raw woods into liquid alkanes with mass yields up to 28.1 wt% over a multifunctional Pt/NbOPO4 catalyst in cyclohexane. The superior performance of this catalyst allows simultaneous conversion of cellulose, hemicellulose and, more significantly, lignin fractions in the wood sawdust into hexane, pentane and alkylcyclohexanes, respectively. Investigation on the molecular mechanism reveals that a synergistic effect between Pt, NbOx species and acidic sites promotes this highly efficient hydrodeoxygenation of bulk lignocellulose. No chemical pretreatment of the raw woody biomass or separation is required for this one-pot process, which opens a general and energy-efficient route for converting raw lignocellulose into valuable alkanes.
-
Incentivizing secondary raw material markets for sustainable waste management.
Schreck, Maximilian; Wagner, Jeffrey
2017-09-01
Notwithstanding several policy initiatives in many countries over a number of years, there remains a general sense that too much municipal solid waste is generated and that too much of the waste that is generated is landfilled. There is an emerging consensus that a sustainable approach to waste management requires further development of secondary raw material markets. The purpose of this paper is to propose a theoretical economic model that focuses upon this stage of a sustainable waste management program and explores policy options that could motivate efficiency in secondary raw material markets. In particular, we show how firm profit and social welfare optimizing objectives can be reconciled in a two-product market of waste management processes: landfilling and material reclamation. Our results provide theoretical support for building out recent Circular Economy initiatives as well as for the relatively recent emergence of landfill mining as a means for procuring secondary raw materials. Copyright © 2017 Elsevier Ltd. All rights reserved.
-
Raw material uranium; Rohstoff Uran
Energy Technology Data Exchange (ETDEWEB)
NONE
2017-03-15
Uranium is an important raw material in human life. Mostly using nuclear fission uranium is used in nuclear medicine, industry and research. The most important application is the generation of electricity in nuclear power plants. Due to the global availability the worldwide uranium supply is guaranties for a long time. The contribution covers the issues medicine, neutron research, energy generation, occurrence, mining, processing, recycling and disposal.
-
Site-specific electronic structure analysis by channeling EELS and first-principles calculations.
Tatsumi, Kazuyoshi; Muto, Shunsuke; Yamamoto, Yu; Ikeno, Hirokazu; Yoshioka, Satoru; Tanaka, Isao
2006-01-01
Site-specific electronic structures were investigated by electron energy loss spectroscopy (EELS) under electron channeling conditions. The Al-K and Mn-L(2,3) electron energy loss near-edge structure (ELNES) of, respectively, NiAl2O4 and Mn3O4 were measured. Deconvolution of the raw spectra with the instrumental resolution function restored the blunt and hidden fine features, which allowed us to interpret the experimental spectral features by comparing with theoretical spectra obtained by first-principles calculations. The present method successfully revealed the electronic structures specific to the differently coordinated cationic sites.
-
MICROBIOLOGY OF RAW MATERIALS USED FOR CONFECTIONARY PRODUCTION
Directory of Open Access Journals (Sweden)
Jana Petrová
2015-02-01
Full Text Available The aim of our study was to evaluate the microbiological quality of raw materials used for preparation of confectionery products. For microbiological evaluation total count of bacteria, mesophilic aerobic bacteria, coliform bacteria, yeast and microscopic filamentous fungi in samples of raw materials used in the manufacture and creams of confectionery products were detected. In addition to these groups of microorganisms the presence of pathogenic microorganisms Salmonella spp. and Staphylococcus aureus in creams was monitored. Products are assessed according to the limit values of the number of microorganisms defined in the Codex Alimentary of the Slovak Republic. For microbiological analysis of confectionery products, sampling of components of confectionary products and cream was carried out according to current health regulations and altogether 65 samples of components and creams were collected: 10 samples of raw materials sugar, 10 samples of flour, 10 samples of butter and 10 samples of eggs, 5 samples of butter yolk from cream-filled disposable bag without rum addition, 5 samples of butter yolk from cream-filled disposable bag with rum addition, 5 samples of cream-filled multiple use paid bag, 5 samples of cream-filled newly purchased paid bag, 5 samples of Venček corpus and 5 samples of the French cubes corpus. From raw material the highest TBC (2.65log CFU was in flour, but the lowest in sugar (1.35 log CFU, the highest years counts was found on flour (2.42, but lowest in butter (1.18, while wasn’t in egg. In samples of creams and corpus were increased occurrence of yeast, coliform bacteria. Salmonella spp. and Staphylococcus aureus weren’t isolated from any tested sample.
-
Tylosin production by Streptomyces fradiae using raw cornmeal in airlift bioreactor.
Choi, Dubok; Choi, On You; Shin, Hyun-Jae; Chung, Dong-Ok; Shin, Dae-Yewn
2007-07-01
Using a 50-l airlift bioreactor, for the effective production of tylosin from Streptomyces fradiae TM-224 using raw cornmeal as the energy source, various environmental factors were studied in flask cultures. The maximum tylosin concentration was obtained at 32 degrees C and pH between 7.0 and 7.5. When seed was inoculated after 24 h of culture, the maximum tylosin concentration, 5.7 g/l, was obtained after 4 days of culture. Various concentrations of raw cornmeal were tested to investigate the optimum initial concentration for the tylosin production. An initial raw cornmeal concentration of 80 g/l gave the highest tylosin concentration, 5.8 g/l, after 5 days of culture. Of the various nitrogen sources, soybean meal and fish meal were found to be the most effective for the production of tylosin. In particular, with the optimal mixing ratio, 12 g/l of soybean meal to 14 g/l of fish meal, 7.2 g/l of tylosin was obtained after 5 days of culture. To compare raw cornmeal and glucose for the production oftylosin in the 50-1 airlift bioreactor for 10 days, fed-batch cultures were carried out under the optimum culture conditions. When raw corn meal was used as the energy source, the tylosin production increased with increasing culture time. The maximum tylosin concentration after 10 days of culture was 13.5 g/l, with a product yield from raw cornmeal of 0.123 g/g of consumed carbon source, which was about 7.2 times higher than that obtained when glucose was used as the carbon source.
-
Mesta/Kenaf as raw material for Kraft pulping
Energy Technology Data Exchange (ETDEWEB)
Saraf, V. P.; Shiveshwar, R. M.; Meshramkar, P. M.; Deb, U. K.; Jaspal, N. S.; Biyani, B. P.
1980-03-15
In recent years, the shortage of conventional raw materials for pulping has intensified a world-wide search for alternate raw materials. Among other cellulosic materials, attention has focused on agricultural residues and annual plants. In this category, Kenaf, also called Mesta, has been studied as a fiber source in many countries including the USA, Phillippines and India. A comprehensive study on kraft pulping of mesta was carried out where the fiber morphology, pulping, bleaching and papermaking characteristics were investigated. Black liquor properties were also determined. The results of this study are reported and compared to the conventional raw material bamboo. The investigation has shown that mesta is easily pulped and bleached and forms sheets of excellent strength properties, comparable to or better than bamboo pulps. The black liquor from mesta is similar to bamboo in calorific value but is very low in silica, which is highly desirable from the chemical recovery point of view. As with all agricultural residues and annual plants, mesta has a high bulk per unit weight. The problems arising from this, e.g., baling, transportation, proper utilization of digester capacity, have to be studied before mesta can be widely accepted in the paper industry.
-
Staphylococcus aureus Enterotoxin A Gene Isolated From Raw Red Meat and Poultry in Tehran, Iran
Directory of Open Access Journals (Sweden)
Mohammad Hossein Sarrafzadeh Zargar
2014-07-01
Full Text Available Background: Staphylococcus aureus is the most prevalent infectious agent of food materials. Enterotoxin producing types of S. aureus cause well-known food-borne disease. Staphylococcal Enterotoxin A (SEA is the most important agent of gastroenteritis. Objectives: The present study aimed to screen the raw meat samples collected from different regions of Tehran for S. aureus infection and type of encoding enterotoxin. Materials and Methods: Hundred and eighty six meat samples were collected randomly from city dealers and transferred to laboratory within screw cap containers. The samples were first cultured according to the standard bacteriological methods and then S. aureus isolates were identified using standard bacteriological tests. The isolates were subjected to Polymerase Chain Reaction (PCR to detect gene encoding SEA. Results: Staphylococcus aureus isolated from 29 (15.6% meat samples including beef 14.8%, raw lamb 15%, raw chicken 15.7% and raw turkey 16.6%. Using special primer sets proved that the species isolated from five samples (two raw chicken, two raw beef and one raw turkey encoded enterotoxin A. Conclusions: Although staphylococcal contamination within food material is more or less a routine, but detection of enterotoxin encoding species from raw meat samples is alarming for health authorities. These data highlight the importance of periodic surveillance of raw meat distributed among ordinary consumers.
-
International Nuclear Information System (INIS)
Dragusin, M.; Rotaru, R.
2000-01-01
Microbiological contamination of herbal raw materials is a serious problem in the production of therapeutical preparations. A good quality of the product, according to the pharmaceutical requirements may be achieved by applying suitable methods of decontamination. The decontamination treatments should be fast and effective against all microorganisms. It should ensure the decontamination of both packaging and the microorganisms present and must not reduce the sensory and technological qualities of the commodities. Decontamination of herbal raw materials by irradiation is a method by choice. It is because chemical methods are recognized recently as not safe to the consumer. Irradiation, in turn, is technically feasible, very effective and friendly enough to environment process. Under the prevailing production and handling conditions, most herbs contain a large number of microorganisms what is a serious problem in the production of therapeutical preparations. For several years the most widely used methods for decontamination of herbs was fumigation with ethylene oxide or methyl bromide. Both methods today banned in most countries. Irradiation is an alternative and safe method for effective reducing the microbial contamination of herbal raw materials. The following raw materials have been examined: Folium Cynara, Folium Plantago, Flos Chamomillae, Semen Sylibum Marianum and Folium Farfara. The content of biologically active compounds before and after irradiation of the raw materials did not change in a significant degree after irradiation. The dose of radiation for herbals raw materials was 10 kGy. There are two groups of raw materials: - The raw materials designed for preparing granulates, tablets, dragees, capsules, aqueous extracts, infusions, macerations and preparations for external use; - The raw materials assigned for preparing alcoholic preparations, isolated compounds, oil preparations and essential oils. The medical herbs and herbal raw materials before their
-
File list: ALL.Bld.05.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available ALL.Bld.05.AllAg.RAW_264PERIOD7 mm9 All antigens Blood RAW 264.7 SRX218749,SRX26459...RX1471834,SRX019779,SRX264581 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/ALL.Bld.05.AllAg.RAW_264PERIOD7.bed ...
-
File list: ALL.Bld.20.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available ALL.Bld.20.AllAg.RAW_264PERIOD7 mm9 All antigens Blood RAW 264.7 SRX264590,SRX26459...RX1471833,SRX019779,SRX264581 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/ALL.Bld.20.AllAg.RAW_264PERIOD7.bed ...
-
File list: ALL.Bld.10.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available ALL.Bld.10.AllAg.RAW_264PERIOD7 mm9 All antigens Blood RAW 264.7 SRX796809,SRX26459...RX1471833,SRX019779,SRX264581 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/ALL.Bld.10.AllAg.RAW_264PERIOD7.bed ...
-
File list: ALL.Bld.50.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available ALL.Bld.50.AllAg.RAW_264PERIOD7 mm9 All antigens Blood RAW 264.7 SRX1471835,SRX2645...SRX434625,SRX264581,SRX019779 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/ALL.Bld.50.AllAg.RAW_264PERIOD7.bed ...
-
Refining of raw materials, lignite present economic problems
Energy Technology Data Exchange (ETDEWEB)
Schirmer, G.
1985-06-01
East Germany seeks an economic intensification program that involves refining raw materials to a higher level. Lignite briquetting prior to liquefaction and gasification illustrates both the theoretical and practical aspects of that goal and also introduces questions of secure supplies. The author describes the special labor processes, use of technology, recycling of waste materials, and other new problems that the approach entails as the refined raw materials become new materials or energy sources. Economics based on the value of the refined product and the cost of the materials determine the degree of refinement. The concept also involves the relationship of producer and user as profits increase.
-
PIMR: Parallel and Integrated Matching for Raw Data.
Li, Zhenghao; Yang, Junying; Zhao, Jiaduo; Han, Peng; Chai, Zhi
2016-01-02
With the trend of high-resolution imaging, computational costs of image matching have substantially increased. In order to find the compromise between accuracy and computation in real-time applications, we bring forward a fast and robust matching algorithm, named parallel and integrated matching for raw data (PIMR). This algorithm not only effectively utilizes the color information of raw data, but also designs a parallel and integrated framework to shorten the time-cost in the demosaicing stage. Experiments show that compared to existing state-of-the-art methods, the proposed algorithm yields a comparable recognition rate, while the total time-cost of imaging and matching is significantly reduced.
-
Cholera after the consumption of raw oysters. A case report.
Klontz, K C; Tauxe, R V; Cook, W L; Riley, W H; Wachsmuth, I K
1987-12-01
In August 1986, a 76-year-old woman in Miami, Florida, developed profuse watery diarrhea and abdominal cramps. Two and four days before the onset of her illness, she had eaten six raw oysters at each of two restaurants in Miami. A stool specimen yielded toxigenic Vibrio cholerae O1 biotype El Tor, serotype Inaba. The results of toxin gene probing of the organism recovered from the patient differed significantly from those of other V. cholerae O1 isolates from the Gulf Coast and elsewhere in the world. A program of active surveillance identified no other cases of cholera in Miami. The source of the raw oysters eaten by the patient was traced to Louisiana. Her case represents the first reported case of cholera associated with eating raw oysters.
-
Electrodermal responses to implied versus actual violence on television.
Kalamas, A D; Gruber, M L
1998-01-01
The electrodermal response (EDR) of children watching a violent show was measured. Particular attention was paid to the type of violence (actual or implied) that prompted an EDR. In addition, the impact of the auditory component (sounds associated with violence) of the show was evaluated. Implied violent stimuli, such as the villain's face, elicited the strongest EDR. The elements that elicited the weakest responses were the actual violent stimuli, such as stabbing. The background noise and voices of the sound track enhanced the total number of EDRs. The results suggest that implied violence may elicit more fear (as measured by EDRs) than actual violence does and that sounds alone contribute significantly to the emotional response to television violence. One should not, therefore, categorically assume that a show with mostly actual violence evokes less fear than one with mostly implied violence.
-
Annual report 1997. Energies and raw materials
International Nuclear Information System (INIS)
1997-01-01
This report gives the important directions of French energy policy. Nuclear energy, electric power, natural gas, coal and petroleum products are reviewed. The situations and the forecasting for raw materials are also given. (N.C.)
-
IceBridge Sigma Space Lidar L0 Raw Time-of-Flight Data
National Aeronautics and Space Administration — The NASA IceBridge Sigma Space Lidar L0 Raw Time-of-Flight Data (ILSIG0) contain raw time-of-flight values for Antarctica and Greenland using the Sigma Space Lidar....
-
A cardiorespiratory classifier of voluntary and involuntary electrodermal activity
Directory of Open Access Journals (Sweden)
Sejdic Ervin
2010-02-01
Full Text Available Abstract Background Electrodermal reactions (EDRs can be attributed to many origins, including spontaneous fluctuations of electrodermal activity (EDA and stimuli such as deep inspirations, voluntary mental activity and startling events. In fields that use EDA as a measure of psychophysiological state, the fact that EDRs may be elicited from many different stimuli is often ignored. This study attempts to classify observed EDRs as voluntary (i.e., generated from intentional respiratory or mental activity or involuntary (i.e., generated from startling events or spontaneous electrodermal fluctuations. Methods Eight able-bodied participants were subjected to conditions that would cause a change in EDA: music imagery, startling noises, and deep inspirations. A user-centered cardiorespiratory classifier consisting of 1 an EDR detector, 2 a respiratory filter and 3 a cardiorespiratory filter was developed to automatically detect a participant's EDRs and to classify the origin of their stimulation as voluntary or involuntary. Results Detected EDRs were classified with a positive predictive value of 78%, a negative predictive value of 81% and an overall accuracy of 78%. Without the classifier, EDRs could only be correctly attributed as voluntary or involuntary with an accuracy of 50%. Conclusions The proposed classifier may enable investigators to form more accurate interpretations of electrodermal activity as a measure of an individual's psychophysiological state.
-
Basic Thermal Parameters of Selected Foods and Food Raw Materials
Monika Božiková; Ľubomír Híreš; Michal Valach; Martin Malínek; Jan Mareček
2017-01-01
In general, processing and manipulation with foods and food raw materials have significant influence on their physical properties. The article is focused on thermophysical parameters measurement of selected foods and food raw materials. There were examined thermal conductivity and thermal diffusivity of selected materials. For detection of thermal parameters was used instrument Isomet 2104, which principle of measurement is based on transient methods. In text are presented summary results of ...
-
Effect of Selected Alternative Fuels and Raw Materials on the Cement Clinker Quality
Directory of Open Access Journals (Sweden)
Strigáč Július
2015-11-01
Full Text Available The article deals with the study of the effects of alternative fuels and raw materials on the cement clinker quality. The clinker quality was expressed by the content of two principal minerals alite C3S and belite C2S. The additions of alternative fuels ashes and raw materials, in principle, always increased the belite content and conversely reduced the amount of alite. The alternative fuels with high ash content were used such as the meat-bone meal, sewage sludge from sewage treatment plants and paper sludge and the used alternative raw materials were metallurgical slags - granulated blastfurnace slag, air cooled blastfurnace slag and demetallized steel slag, fluidized bed combustion fly ash and waste glass. Meat-bone meal, sewage sludge from sewage treatment plants and paper sludge were evaluated as moderately suitable alternative fuels which can be added in the amounts of 2.8 wt. % addition of meat-bone meals ash, 3.64 wt. % addition of sewage sludge ash and 3.8 wt. % addition of paper sludge ash to the cement raw mixture. Demetallised steel slag is suitable for production of special sulphate resistant cement clinker for CEM I –SR cement with addition up to 5 wt. %. Granulated blastfurnace slag is a suitable alternative raw material with addition 4 wt. %. Air cooled blastfurnace slag is a suitable alternative raw material with addition 4.2 wt. %. Waste glass is not very appropriate alternative raw material with addition only 1.16 wt. %. Fluidized bed combustion fly ash appears not to be equally appropriate alternative raw material for cement clinker burning with less potential utilization in the cement industry and with addition 3.41 wt. %, which forms undesired anhydrite CaSO4 in the cement clinker.
-
DEFF Research Database (Denmark)
Wilson, Alexander
2014-01-01
, and a contemporary zeitgeist marked by a general relativisation of aesthetic values has emerged, exploding into a plethora of parallel discourses on art. Perhaps there is no longer such a thing (if there ever was) as Culture with a capital C, which Dubuffet so vehemently opposed in his championing of art brut......’s adolescence without hypostatizing distinctions between inside and outside, or between culture and its raw or primitive origins, while nevertheless not conflating the dissolution of boundaries and hierarchies with a possible end to territoriality and control, nor promoting a resignation of thought...
-
VIIRS Climate Raw Data Record (C-RDR) from Suomi NPP, Version 1
National Oceanic and Atmospheric Administration, Department of Commerce — The Suomi NPP Climate Raw Data Record (C-RDR) developed at the NOAA NCDC is an intermediate product processing level (NOAA Level 1b) between a Raw Data Record (RDR)...
-
Aluminium reprocessing with local mineral raw material
International Nuclear Information System (INIS)
Mirsaidov, U.M.
2002-01-01
With the purpose of utilization of ice sediment, receiving from mud fields solutions and flotation tails and at using local aluminium and fluorine-containing raw material was elaborated fundamental technologic scheme presented in this chapter of book
-
Utilization of Iron Ore Tailings as Raw Material for Portland Cement Clinker Production
Directory of Open Access Journals (Sweden)
Li Luo
2016-01-01
Full Text Available The cement industry has for some time been seeking alternative raw material for the Portland cement clinker production. The aim of this research was to investigate the possibility of utilizing iron ore tailings (IOT to replace clay as alumina-silicate raw material for the production of Portland cement clinker. For this purpose, two kinds of clinkers were prepared: one was prepared by IOT; the other was prepared by clay as a reference. The reactivity and burnability of raw meal, mineralogical composition and physical properties of clinker, and hydration characteristic of cement were studied by burnability analysis, differential thermal analysis, X-ray diffraction, and hydration analysis. The results showed that the raw meal containing IOT had higher reactivity and burnability than the raw meal containing clay, and the use of IOT did not affect the formation of characteristic mineralogical phases of Portland cement clinker. Furthermore, the physical and mechanical performance of two cement clinkers were similar. In addition, the use of IOT was found to improve the grindability of clinker and lower the hydration heat of Portland cement. These findings suggest that IOT can replace the clay as alumina-silicate raw material for the preparation of Portland cement clinker.
-
Reflections on prospective raw materials and materials with regard to the Czech Republic
International Nuclear Information System (INIS)
Schejbal, C.; Palas, M.
1997-01-01
Reflections on prospective mineral raw materials and materials must rest upon the expected demographic evolution, the evaluation of economic development and the development of manufacturing technologies and materials corresponding to them, trends in the consumption of mineral raw materials and possibilities of securing them. The evaluation of the given factors under conditions of the Czech Republic shows that one of the decisive prerequisites to transforming the Czech economy is to assure the fuel and energy security of the state. In addition to emphasis put on traditional and newly developed technologies of utilization of domestic resources of coal and the development of nuclear power, a diversification of supplies of oil and gas is necessary. Moreover, it is necessary to ensure domestic resources of raw materials to some prospective material areas, or to provide these raw materials by means of imports and/or entrepreneurial activity abroad. As far as raw materials for building and industrial rocks are concerned, it is necessary to support the exploitation and home utilization through laws and suitable economic tools at respecting environmental limitations. With non-traditional prospective raw materials, it will be desirable to promote exploration and mining especially in those cases when a precondition exists for the securing of sufficient reserves or when reserves are already known
-
File list: His.Bld.10.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available His.Bld.10.AllAg.RAW_264PERIOD7 mm9 Histone Blood RAW 264.7 SRX796809,SRX264590,SRX...264591,SRX796810,SRX796812,SRX796811,SRX264592,SRX264593 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/His.Bld.10.AllAg.RAW_264PERIOD7.bed ...
-
File list: His.Bld.20.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available His.Bld.20.AllAg.RAW_264PERIOD7 mm9 Histone Blood RAW 264.7 SRX264590,SRX796810,SRX...796809,SRX796812,SRX264591,SRX796811,SRX264592,SRX264593 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/His.Bld.20.AllAg.RAW_264PERIOD7.bed ...
-
File list: His.Bld.50.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available His.Bld.50.AllAg.RAW_264PERIOD7 mm9 Histone Blood RAW 264.7 SRX264590,SRX796809,SRX...796810,SRX264592,SRX796812,SRX796811,SRX264593,SRX264591 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/His.Bld.50.AllAg.RAW_264PERIOD7.bed ...
-
File list: His.Bld.05.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available His.Bld.05.AllAg.RAW_264PERIOD7 mm9 Histone Blood RAW 264.7 SRX264592,SRX796810,SRX...796809,SRX264590,SRX264591,SRX796812,SRX796811,SRX264593 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/His.Bld.05.AllAg.RAW_264PERIOD7.bed ...
-
Quantitative analysis of raw materials mining of Sverdlovsk region in Russia
Tarasyev, Alexander M.; Vasilev, Julian; Turygina, Victoria F.
2016-06-01
The purpose of this article is to show the application of some qualitative methods for the analysis of a dataset for raw materials. The main approaches used are related to the correlation analysis and forecasting with trend lines. It is proved that the future mining of particular ores can be predicted on the basis of mathematical modeling. It is also shown that there exists a strong correlation between the mining of some specific raw materials. Some of the revealed correlations have meaningful explanations, and for others one should look for sophisticated interpretations. The applied approach can be used for forecasting of raw materials exploitation in various regions of Russia and in other countries.
-
Raw materials for the energy supply of the future. Geology, markets, environmental influences
International Nuclear Information System (INIS)
Hagelueken, Christian; Thauer, Rudolf K.; Buchholz, Peter; Gutzmer, Jens; Littke, Ralf; Angerer, Gerhard; Wellmer, Friedrich-Wilhelm
2015-01-01
More and more metals are needed to expand modern energy technologies, but we can not completely dispense with fossil raw materials and biomass in the near future either. Are the incidence of the conversion of energy sources sufficient? The analysis of the academy project ''Energy Systems of the Future'' (ESYS) comes to the conclusion that geologically enough raw materials are available. The challenge, however, is to make the supply safe, affordable and environmentally and socially compatible. The analysis explains the mechanisms of action on the global commodity markets and identifies supply risks. These include, for example, sudden demand on the international markets as well as the unequal distribution of the world's raw material reserves. This is followed by the analysis approaches, in order to recognize warning signals for potential raw material bottlenecks in time, to develop evasive strategies and to secure the raw material supply for the energy turnarounds. For example, the expansion of recycling can help to reduce the dependence on metal imports. In mining, on the other hand, innovative technologies have to be developed in order to improve the exploration and utilization of the deposits. By establishing binding environmental and social standards, the extraction of raw materials could also become more sustainable. The analysis also highlights the importance of bioenergy and fossil raw materials, such as oil and natural gas, for energy generation. The authors describe the advantages and disadvantages of these energy carriers and the measures that can be used to reduce environmental pollution such as greenhouse gas emissions. [de
-
STATISTICAL ANALYSIS OF RAW SUGAR MATERIAL FOR SUGAR PRODUCER COMPLEX
A. A. Gromkovskii; O. I. Sherstyuk
2015-01-01
Summary. In the article examines the statistical data on the development of average weight and average sugar content of sugar beet roots. The successful solution of the problem of forecasting these raw indices is essential for solving problems of sugar producing complex control. In the paper by calculating the autocorrelation function demonstrated that the predominant trend component of the growth raw characteristics. For construct the prediction model is proposed to use an autoregressive fir...
-
Replacement Value of Soybean Meal and Maize with Raw or Boiled ...
African Journals Online (AJOL)
A study to determine the replacement value of raw or boiled pigeon pea seed meal (PSM) for soybean meal and maize in the diets of exotic pullets (1-56 d) was conducted with 324 pullet chicks. The experimental design was 2 x 5 factorial in a completely randomized design (CRD). The factors were form (raw and boiled) ...
-
Study on optimum length of raw material in stainless steel high-lock nuts forging
Cheng, Meiwen; Liu, Fenglei; Zhao, Qingyun; Wang, Lidong
2018-04-01
Taking 302 stainless steel (1Cr18Ni9) high-lock nuts for research objects, adjusting the length of raw material, then using DEFORM software to simulate the isothermal forging process of each station and conducting the corresponding field tests to study the effects of raw material size on the stainless steel high-lock nuts forming performance. The tests show that the samples of each raw material length is basically the same as the results of the DEFORM software. When the length of the raw material is 10mm, the appearance size of the parts can meet the design requirements.
-
Correia, Victor; Allington, Ruth; Keane, Christopher
2016-04-01
A secure supply of raw materials is a European priority that extends beyond country borders and national policies. Recent European initiatives have pioneered the development of an EU strategy on raw materials emphasizing the concept of the "added value chain", which continues to pursue the three pillar strategy to: (1) ensure the fair and sustainable supply of raw materials from international markets, promoting international cooperation with developed and developing countries; (2) foster sustainable supply of raw materials from European sources, and (3) reduce consumption of primary raw materials by increasing resource efficiency and promoting recycling. This contribution presents the Horizon 2020 funded project INTRAW, the objective of which is to establish the European Union's International Observatory for Raw Materials. The creation and maintenance of the European Union's International Observatory for Raw Materials is designed to have a strong impact in two dimensions: 1. To narrow the existing gap in aspects of the raw materials knowledge infrastructure in the EU by providing a link with the same knowledge infrastructure in technologically advanced reference countries. This should contribute to the harmonization of mineral policies all over the EU, by providing data that enables evidence-based policies and appropriate, cost-effective management, planning and adaptation decisions by the public sector. This will benefit businesses, industry and society. The Observatory will also provide to policy makers in the EU and its Member States the data they need to facilitate discussion in multilateral forums. 2. To enable a better alignment of the R&I activities among the individual EU members and international cooperation countries AND between the European Union and international cooperation countries by boosting synergies with international research and innovation programmes. This way the EU's role and scientific capabilities in the raw materials area will be
-
MCKissick, Burnell T. (Technical Monitor); Plassman, Gerald E.; Mall, Gerald H.; Quagliano, John R.
2005-01-01
Linear multivariable regression models for predicting day and night Eddy Dissipation Rate (EDR) from available meteorological data sources are defined and validated. Model definition is based on a combination of 1997-2000 Dallas/Fort Worth (DFW) data sources, EDR from Aircraft Vortex Spacing System (AVOSS) deployment data, and regression variables primarily from corresponding Automated Surface Observation System (ASOS) data. Model validation is accomplished through EDR predictions on a similar combination of 1994-1995 Memphis (MEM) AVOSS and ASOS data. Model forms include an intercept plus a single term of fixed optimal power for each of these regression variables; 30-minute forward averaged mean and variance of near-surface wind speed and temperature, variance of wind direction, and a discrete cloud cover metric. Distinct day and night models, regressing on EDR and the natural log of EDR respectively, yield best performance and avoid model discontinuity over day/night data boundaries.
-
COMPOSITIONAL EVALUATION OF RAW AND PROCESSED HARMS (Brachystegia eurycoma SEED FLOUR
Directory of Open Access Journals (Sweden)
M.O Aremu
2014-12-01
Full Text Available Brachystegia eurycoma is predominantly grown in the eastern region of Nigeria. Its seed is used in food majorly as a soup condiment, flavouring agent and soup thickener. The proximate, mineral and amino acid compositions were determined on raw and processed seeds (boiled, fermented and roasted using standard analytical techniques. The processing methods showed deviations in nutrients from the raw seeds. The crude protein was reduced by the processing methods with exception of roasting method. Crude fat was reduced in all the processing methods in this order: Raw > fermented > roasted > boiled samples. All the processing methods enhanced calcium content in this order: Raw < boiled < fermented < roasted samples. Boiling and fermenting reduced the content of magnesium by 72.6 and 30.2%, respectively while boiling, fermenting and roasting increased potassium content by 124.5, 12.2 and 120.4%, respectively. Generally, all the samples were found to be a good source of essential minerals and harmful heavy metals such as lead, chromium, arsenic and cadmium were not at detectable range of atomic absorption spectrophotometer. The amino acid profile revealed that amino acids in fermented sample were better concentrated than that of raw and other processed samples. The total essential amino acids (TEAA ranged from 28.63 g/100g crude protein in roasted sample to 34.79 g/100g crude protein in fermented sample. The limiting amino acid (LAA for all the samples was Met + Cys (TSAA.
-
Comparison of breast percent density estimation from raw versus processed digital mammograms
Li, Diane; Gavenonis, Sara; Conant, Emily; Kontos, Despina
2011-03-01
We compared breast percent density (PD%) measures obtained from raw and post-processed digital mammographic (DM) images. Bilateral raw and post-processed medio-lateral oblique (MLO) images from 81 screening studies were retrospectively analyzed. Image acquisition was performed with a GE Healthcare DS full-field DM system. Image post-processing was performed using the PremiumViewTM algorithm (GE Healthcare). Area-based breast PD% was estimated by a radiologist using a semi-automated image thresholding technique (Cumulus, Univ. Toronto). Comparison of breast PD% between raw and post-processed DM images was performed using the Pearson correlation (r), linear regression, and Student's t-test. Intra-reader variability was assessed with a repeat read on the same data-set. Our results show that breast PD% measurements from raw and post-processed DM images have a high correlation (r=0.98, R2=0.95, p<0.001). Paired t-test comparison of breast PD% between the raw and the post-processed images showed a statistically significant difference equal to 1.2% (p = 0.006). Our results suggest that the relatively small magnitude of the absolute difference in PD% between raw and post-processed DM images is unlikely to be clinically significant in breast cancer risk stratification. Therefore, it may be feasible to use post-processed DM images for breast PD% estimation in clinical settings. Since most breast imaging clinics routinely use and store only the post-processed DM images, breast PD% estimation from post-processed data may accelerate the integration of breast density in breast cancer risk assessment models used in clinical practice.
-
Consumption of raw or unpasteurized milk and milk products by pregnant women and children.
2014-01-01
Sales of raw or unpasteurized milk and milk products are still legal in at least 30 states in the United States. Raw milk and milk products from cows, goats, and sheep continue to be a source of bacterial infections attributable to a number of virulent pathogens, including Listeria monocytogenes, Campylobacter jejuni, Salmonella species, Brucella species, and Escherichia coli O157. These infections can occur in both healthy and immunocompromised individuals, including older adults, infants, young children, and pregnant women and their unborn fetuses, in whom life-threatening infections and fetal miscarriage can occur. Efforts to limit the sale of raw milk products have met with opposition from those who are proponents of the purported health benefits of consuming raw milk products, which contain natural or unprocessed factors not inactivated by pasteurization. However, the benefits of these natural factors have not been clearly demonstrated in evidence-based studies and, therefore, do not outweigh the risks of raw milk consumption. Substantial data suggest that pasteurized milk confers equivalent health benefits compared with raw milk, without the additional risk of bacterial infections. The purpose of this policy statement was to review the risks of raw milk consumption in the United States and to provide evidence of the risks of infectious complications associated with consumption of unpasteurized milk and milk products, especially among pregnant women, infants, and children.
-
Effects of storage on the major constituents of raw milk
Directory of Open Access Journals (Sweden)
Peter Zajác
2015-10-01
Full Text Available Milk testing and quality control should be carried out at all stages of the dairy chain. Milk can be tested for quantity, organoleptic characteristic, compositional characteristic, physical and chemical characteristics, hygienic characteristics, adulteration or drug residues. The content of the major constituents of raw milk is important for milk payment system. Enzymes naturally present in the milk can change the chemical composition of raw milk. Also, enzymes secreted by bacteria or enzymes from somatic cells can degrade the raw milk composition. Products of these degradation reactions can have undesirable effects on milk structure, smell and taste. It is very important that farm-fresh raw milk be cooled immediately to not more than 8 °C in the case of daily collection, or not more than 6 °C if collection is not daily. During transport the cold chain must be maintained. An authorized person, properly trained in the appropriate technique, shall perform sampling of bulk milk in farm. Laboratory samples should be dispatched immediately after sampling to the dairy company and consequently to the testing laboratory. The time for dispatch of the samples to the testing laboratory should be as short as possible, preferably within 24 h. Laboratory samples shall be transported and stored at temperature 1 to 5 °C. Higher temperatures may adversely affect the composition of the laboratory sample and may cause disputes between the farmer, the dairy company and the laboratory. The effect of refrigerated storage at temperature 4 °C during 24 h on the composition of raw milk were investigated in this work, because we wanted to know how the milk composition will be changed and how the laboratory results will be affected. In many cases, the samples are not preserved with chemical preservants like azidiol, bronopol, potassium dichromate or Microtabs. We found, that the composition of raw cows' milk after 24 was changed significantly (p >0.005. We found an
-
Polymer Industrial Floors - The Possibility of Using Secondary Raw Materials from Solar Panels
J. Kosikova; B. Vacenovska; M. Vyhnankova
2014-01-01
The paper reports on the subject of recycling and further use of secondary raw materials obtained from solar panels, which is becoming a very up to date topic in recent years. Recycling these panels is very difficult and complex, and the use of resulting secondary raw materials is still not fully resolved. Within the research carried out at the Brno University of Technology, new polymer materials used for industrial floors are being developed. Secondary raw materials are ...
-
Tracking upper limbs fatigue by means of electronic dynamometry
Directory of Open Access Journals (Sweden)
Fernando Max Lima
2015-06-01
Full Text Available This study aimed to identify useful electronic grip dynamometry parameters to track differences between trained (TR and untrained (UT participants, and between dominant (DO and non-dominant (ND limbs as a consequence of upper limbs muscle fatigue following 10 RM tests of the brachial biceps. This experimental study with transversal design involved 18 young adult males, of whom 9 were untrained and 9 were experienced in resistance training.Isometric grip force was evaluated (30 seconds long previous and after 10RM tests by means of a G200 Model grip dynamometer with precision load cell (Biometrics(r. Significant differences between initial and final measurements were found only for trained participants: Peak force for TR-DO (67.1 vs 55.5 kgf, p = .0277; Raw average for TR-DO (46.96 vs 42.22 kgf, p = .0464, and for TR-ND (40.34 vs 36.13 kgf, p = .0277. Electronic grip dynamometry efficiently identified upper limbs fatigue in trained participants, being raw average measurements the best parameter.
-
Evolution and characterization of eggshell as a potential candidate of raw material
Directory of Open Access Journals (Sweden)
T. Zaman
Full Text Available Abstract Characterization of both uncalcined and calcined eggshells was done in this work. Raw eggshells turned out as a good source of calcite phase. Calcined eggshells had a mixture of lime and portlandite phase. A significant impact of calcination temperature on the percentage of generated phases was observed. Qualitative as well as semi-quantitative phase analysis, morphological characterization and physical property estimation was done for the produced powder. The influence of synthesized raw material on soil stabilization and biomaterial formation was further assessed. The eggshell turned out as a potential source of raw material for various sectors.
-
Some characteristics of a raw starch digestion inhibitory factor from Aspergillus niger
Energy Technology Data Exchange (ETDEWEB)
Towprayoon, S.; Saha, B.C.; Fujio, Yusaku; Ueda, Seinosuke
1988-09-01
The effect of an inhibitory factor (IF) from Aspergillus niger 19 on raw starch digestion by pure glucoamylase I of black Aspergillus, pure glucoamylase of Rhizopus niveus, bacterial ..cap alpha..-amylase, fungal ..cap alpha..-amylase and various combination was investigated. The IF caused higher inhibition of raw starch hydrolysis by the combined action of glucoamylase and fungal ..cap alpha..-amylase than of hydrolysis by the individual enzymes. A protein moiety of IF might play an active part in this inhibition phenomenon. The IF was found to starch granules, preventing hydrolysis by the enzymes, and caused decreased raw starch hydrolysis yields.
-
Raw and Heat-Treated Milk: From Public Health Risks to Nutritional Quality
Directory of Open Access Journals (Sweden)
Francesca Melini
2017-11-01
Full Text Available Consumers have recently shown a preference for natural food products and ingredients and within that framework, their interest in consuming raw drinking milk has been highlighted, claiming nutritional, organoleptic and health benefits. However, a public debate has simultaneously emerged about the actual risks and benefits of direct human consumption of raw milk. This paper compares the microbiological, nutritional and sensory profile of raw and heat-treated milk, to evaluate the real risks and benefits of its consumption. In detail, it provides an updated overview of the main microbiological risks of raw milk consumption, especially related to the presence of pathogens and the main outputs of risk assessment models are reported. After introducing the key aspects of most commonly used milk heat-treatments, the paper also discusses the effects such technologies have on the microbiological, nutritional and sensory profile of milk. An insight into the scientific evidence behind the claimed protective effects of raw milk consumption in lactose-intolerant subjects and against the onset of asthma and allergy disorders in children is provided. The emergence of novel milk processing technologies, such as ohmic heating, microwave heating, high pressure processing, pulsed electric fields, ultrasound and microfiltration is also presented as an alternative to common thermal treatments.
-
Patel, Sanjay K S; Mardina, Primata; Kim, Dongwook; Kim, Sang-Yong; Kalia, Vipin C; Kim, In-Won; Lee, Jung-Kul
2016-10-01
Raw biogas can be an alternative feedstock to pure methane (CH4) for methanol production. In this investigation, we evaluated the methanol production potential of Methylosinus sporium from raw biogas originated from an anaerobic digester. Furthermore, the roles of different gases in methanol production were investigated using synthetic gas mixtures of CH4, carbon dioxide (CO2), and hydrogen (H2). Maximum methanol production was 5.13, 4.35, 6.28, 7.16, 0.38, and 0.36mM from raw biogas, CH4:CO2, CH4:H2, CH4:CO2:H2, CO2, and CO2:H2, respectively. Supplementation of H2 into raw biogas increased methanol production up to 3.5-fold. Additionally, covalent immobilization of M. sporium on chitosan resulted in higher methanol production from raw biogas. This study provides a suitable approach to improve methanol production using low cost raw biogas as a feed containing high concentrations of H2S (0.13%). To our knowledge, this is the first report on methanol production from raw biogas, using immobilized cells of methanotrophs. Copyright © 2016 Elsevier Ltd. All rights reserved.
-
Model-based PEEP optimisation in mechanical ventilation
Directory of Open Access Journals (Sweden)
Chiew Yeong Shiong
2011-12-01
Full Text Available Abstract Background Acute Respiratory Distress Syndrome (ARDS patients require mechanical ventilation (MV for breathing support. Patient-specific PEEP is encouraged for treating different patients but there is no well established method in optimal PEEP selection. Methods A study of 10 patients diagnosed with ALI/ARDS whom underwent recruitment manoeuvre is carried out. Airway pressure and flow data are used to identify patient-specific constant lung elastance (Elung and time-variant dynamic lung elastance (Edrs at each PEEP level (increments of 5cmH2O, for a single compartment linear lung model using integral-based methods. Optimal PEEP is estimated using Elung versus PEEP, Edrs-Pressure curve and Edrs Area at minimum elastance (maximum compliance and the inflection of the curves (diminishing return. Results are compared to clinically selected PEEP values. The trials and use of the data were approved by the New Zealand South Island Regional Ethics Committee. Results Median absolute percentage fitting error to the data when estimating time-variant Edrs is 0.9% (IQR = 0.5-2.4 and 5.6% [IQR: 1.8-11.3] when estimating constant Elung. Both Elung and Edrs decrease with PEEP to a minimum, before rising, and indicating potential over-inflation. Median Edrs over all patients across all PEEP values was 32.2 cmH2O/l [IQR: 26.1-46.6], reflecting the heterogeneity of ALI/ARDS patients, and their response to PEEP, that complicates standard approaches to PEEP selection. All Edrs-Pressure curves have a clear inflection point before minimum Edrs, making PEEP selection straightforward. Model-based selected PEEP using the proposed metrics were higher than clinically selected values in 7/10 cases. Conclusion Continuous monitoring of the patient-specific Elung and Edrs and minimally invasive PEEP titration provide a unique, patient-specific and physiologically relevant metric to optimize PEEP selection with minimal disruption of MV therapy.
-
Replacement of raw soybean with roasted soybean increased milk production in Holstein cows
Directory of Open Access Journals (Sweden)
Gilson Sebastião Dias Júnior
Full Text Available ABSTRACT: The aim of this study was to evaluate the effect of total replacement of raw whole soybean (RAW for roastedwhole soybean (ROS on the production performance of Holstein cows. Two experiments were carried out usinga simple reversal design where RAW has been completely replaced by ROS. In experiment 1, 22 cows (175±60 days in milkwere used, and the dietary inclusion level of RAW or ROS was 3.7% of dry matter (DM. In experiment 2, 16 cows (130±50 days in milkwere used, and thedietary inclusion level of RAW or ROS was 11% of DM. In both experiments, ROS increased milk production by 1.1kgday-1 without changing fat and protein production. Dry matter intake or milk urea nitrogenwere not affected by dietary soy source. In experiment 2, plasma glucose concentration was decreased, and allantoin/creatinine ratio in urine tended to decreasein ROS. Experiment 2 also evaluated the nutrient digestibility and ruminal degradation kinetics of crude protein in two soybean sources. Roasting had no effect on the digestibility of DM, organic matter, and neutral detergent fiber. Roasted whole soybean hadgreater fraction B and lower protein degradation rate than did RAW; this showed that heat treatment was effective in increasing therumen undegradable amino acid flowto the animal, which suggesteda potential mechanism of action for improved performance observed in ROS.
-
Reliability study: raw and make-up water system, Portsmouth Gaseous Diffusion Plant
International Nuclear Information System (INIS)
Peterman, S.M.; Wiehle, W.E.; Walder, A.; Houk, T.C.; West, R.M.
1981-09-01
A reliability study for determining the ability of the raw and make-up water system to provide reliable and adequate service through the year 2000 has been completed. This study includes an evaluation of the well fields, X-608 Raw Water Pump House, X-605 Booster Station Complex, X-611 Water Treatment Complex, and the associated piping. The raw and make-up water system is in good overall condition, but to maintain this condition, the reliability study team made the following recommendations: (1) increase well field capacity; (2) replace certain speed reducers at X-611; (3) repair deteriorated poles, crossarms, and accessories on F-2 and W-1 feeders; (4) stabilize the landslide in vicinity of the 48 in. raw water main; and (5) initiate further investigation, testing, or engineering studies to correct deficiencies in the supervisory control system between well fields, pump house, and X-611, and determine if the 2400 volt underground cables to X-608A wells should be replaced
-
Energy Technology Data Exchange (ETDEWEB)
Vega R, J. L.; Cayllahua, F.; Apaza, D. G.; Javier, H., E-mail: josevegaramirez@yahoo.es [Universidad Nacional de San Agustin, Departamento de Fisica, Av. Independencia s/n, Arequipa (Peru)
2015-10-15
Percentage depth dose curves were obtained with TLD-100 dosimeters, EDR2 films and Penelope simulation at the interfaces in an inhomogeneous mannequin, composed by equivalent materials to the human body built for this study, consisting of cylindrical plates of solid water-bone-lung-bone-solid water of 15 cm in diameter and 1 cm in height; plates were placed in descending way (4-2-8-2-4). Irradiated with Co-60 source (Theratron Equinox-100) for small radiation fields 3 x 3 cm{sup 2} and 1 x 1 cm{sup 2} at a surface source distance of 100 cm from mannequin. The TLD-100 dosimeters were placed in the center of each plate of mannequin irradiated at 10 Gy. The results were compared between these measurement techniques, giving good agreement in interfaces better than 97%. This study was compared with the same characteristics of another study realized with other equivalent materials to human body not homogeneous acrylic-bone-cork-bone-acrylic. The percentage depth dose curves were obtained with mini-dosimeters L-alanine of 1 mm in diameter and 3 mm in height and 3.5 to 4.0 mg of mass with spectrometer band K (EPR). The mini-dosimeters were irradiated with a lineal accelerator PRIMUS Siemens 6 MV. The results of percentage depth dose of L-alanine mini-dosimeters show a good agreement with the percentage depth dose curves of Penelope code, better than 97.7% in interfaces of tissues. (Author)
-
Cryo-transmission electron tomography of native casein micelles from bovine milk
Trejo, R.; Dokland, T.; Jurat-Fuentes, J.; Harte, F.
2013-01-01
Caseins are the principal protein components in milk and an important ingredient in the food industry. In liquid milk, caseins are found as micelles of casein proteins and colloidal calcium nanoclusters. Casein micelles were isolated from raw skim milk by size exclusion chromatography and suspended in milk protein-free serum produced by ultrafiltration (molecular weight cut-off of 3 kDa) of raw skim milk. The micelles were imaged by cryo-electron microscopy and subjected to tomographic reconstruction methods to visualize the 3-dimensional and internal organization of native casein micelles. This provided new insights into the internal architecture of the casein micelle that had not been apparent from prior cryo-transmission electron microscopy studies. This analysis demonstrated the presence of water-filled cavities (~20 to 30 nm in diameter), channels (diameter greater than ~5 nm), and several hundred high-density nanoclusters (6 to 12 nm in diameter) within the interior of the micelles. No spherical protein submicellar structures were observed. PMID:22118067
-
Oat raw materials and bakery products - amino acid composition and celiac immunoreactivity.
Mickowska, Barbara; Litwinek, Dorota; Gambuś, Halina
2016-01-01
The aim of this study was to compare the biochemical and immunochemical properties of avenins in some special oat raw materials and additionally the possibility of using them as a raw material for the gluten-free bakery products. The compared oat raw materials were - oat flakes, commercial oat flours (including gluten-free oat flour) and residual oat flour, which is by-product of β-glucan preparation. Biochemical characteristic included amino acid compositions and SDS-PAGE profiles of extracted avenins. The immunochemical reactivity with polyclonal anti-gluten and monoclonal anti-gliadin antibodies was evaluated qualitatively and quantitatively by immunoblotting and ELISA methods. Additionally, experimental bakery products made of examined raw materials were assessed according to their suitability for the celiac patients' diet. The highest protein content was measured in the β-glucan preparation "Betaven" and gluten-free oat flour. Proteins of all materials are rich in glutamic and aspartic acid, leucine and arginine. Proportions of amino acids in avenins extracted from most of oat raw materials are similar, excluding gluten-free oat flour, which has a very low avenin content and proportions of individual amino acids are different. The SDS-PAGE protein pattern consisted of proteins with molecular weight of about 25-35 kDa. Polyclonal anti-gluten anti-body recognized all protein fractions of molecular weight higher than 20 kDa. Quantitative ELISA analysis shows that the majority of samples has a gliadin-like protein content within the range of 80-260 mg/kg, excluding gluten-free flours and corresponding bakery products. Altogether, β-glucan preparation has extremely high level of gliadin-like proteins. In the examined oat raw materials and foods the contents of immunoreactive amino acid sequences exceeded the limit of 20 mg/kg (considered as gluten-free) except for gluten-free flours (oat and the prepared mixture) and the bakery products based on gluten
-
"Don't Have A Cow, Man!": Recognizing Herd Share Agreements for Raw Milk.
Mayer, Timothy J
2015-01-01
Dissatisfaction with the industrial model of food production has caused many consumers to seek out food produced on local, family-scale farms that use U.S. Department of Agriculture certified organic or other sustainable practices to grow their food and raise their livestock. While almost all of the types of food that are available at the grocery store can also be found at the local farmers market, one food that is difficult to find in many states is raw milk—that is, milk that has not undergone pasteurization (heat treatment). This difficulty lies in the fact that most states prohibit the direct retail sale of raw milk to the final consumer because public health officials and state legislators fear that raw milk may contain bacteria harmful to human health such as E. coli, Campylobacter, and Listeria. However, some consumers reject these warnings and instead believe that raw milk possesses both nutritional and medicinal qualities. Indeed, an ever-increasing body of scientific research published in peer-reviewed journals supports the claim that raw milk consumption can mitigate or prevent some allergies and infections, especially in young children. In order for consumers to obtain raw milk in states where its sale is prohibited, some consumers have entered into arrangements with farmers known as “herd sharing,” through which the consumer effectively becomes an owner of the herd of cows or goats. For the price of the share and a monthly boarding fee, the shareholder can receive a weekly distribution of the herd’s primary dividend, namely the raw milk. Several states expressly permit this practice while most are silent and still a few prohibit it outright. The three courts in the United States that have ruled on herd share agreements have split, with two courts rejecting the agreements as a circumvention of the state’s prohibition on the sale of raw milk, and the other court assuming the agreement’s validity in light of the state’s failure to adequately
-
File list: InP.Bld.05.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available InP.Bld.05.AllAg.RAW_264PERIOD7 mm9 Input control Blood RAW 264.7 SRX796814,SRX7968...13,SRX1471833 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.05.AllAg.RAW_264PERIOD7.bed ...
-
File list: InP.Bld.10.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available InP.Bld.10.AllAg.RAW_264PERIOD7 mm9 Input control Blood RAW 264.7 SRX796814,SRX7968...13,SRX1471833 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.10.AllAg.RAW_264PERIOD7.bed ...
-
File list: InP.Bld.20.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available InP.Bld.20.AllAg.RAW_264PERIOD7 mm9 Input control Blood RAW 264.7 SRX796813,SRX7968...14,SRX1471833 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.20.AllAg.RAW_264PERIOD7.bed ...
-
File list: InP.Bld.50.AllAg.RAW_264PERIOD7 [Chip-atlas[Archive
Lifescience Database Archive (English)
Full Text Available InP.Bld.50.AllAg.RAW_264PERIOD7 mm9 Input control Blood RAW 264.7 SRX1471833,SRX796...814,SRX796813 http://dbarchive.biosciencedbc.jp/kyushu-u/mm9/assembled/InP.Bld.50.AllAg.RAW_264PERIOD7.bed ...
-
Management and recycling of electronic waste
International Nuclear Information System (INIS)
Tanskanen, Pia
2013-01-01
Waste electrical and electronic equipment (WEEE) is one of the largest growing waste streams globally. Hence, for a sustainable environment and the economic recovery of valuable material for reuse, the efficient recycling of electronic scrap has been rendered indispensable, and must still be regarded as a major challenge for today’s society. In contrast to the well-established recycling of metallic scrap, it is much more complicated to recycle electronics products which have reached the end of their life as they contain many different types of material types integrated into each other. As illustrated primarily for the recycling of mobile phones, the efficient recycling of WEEE is not only a challenge for the recycling industry; it is also often a question of as-yet insufficient collection infrastructures and poor collection efficiencies, and a considerable lack of the consumer’s awareness for the potential of recycling electronics for the benefit of the environment, as well as for savings in energy and raw materials
-
2013-02-01
Standard sample sets of cement and mortar formulations with known levels of Cl as well as concrete samples subject to Cl diffusion were all prepared for and analyzed with scanning electron microscopy (SEM) and electron microprobe (EPMA). Using x-ray ...
-
1996 Activities report on energies and raw materials
International Nuclear Information System (INIS)
1996-01-01
The 1996 activity survey of the French General Directory for Energy and Raw Materials, which main objectives are to preserve the competitiveness of French economy, enhance environmental protection, secure the long term supply safety and maintain the public service basis for energy supply, is presented. The main themes of the survey are: the nuclear safety in Eastern Europe, the electric power inland market, the evolution of the oil market in 1996, the situation of refining in France, restructuring the BRGM (Mining and Geological Research Bureau), followed by brief facts concerning the sustainable energy development, nuclear energy, electric power, electricity and gas common issues, gas, coal, petroleum products, raw materials and underground materials. A series of global diagrams concludes the survey
-
Effect of raw milk on lactose intolerance: a randomized controlled pilot study.
Mummah, Sarah; Oelrich, Beibei; Hope, Jessica; Vu, Quyen; Gardner, Christopher D
2014-01-01
This pilot study aimed to determine whether raw milk reduces lactose malabsorption and/or lactose intolerance symptoms relative to pasteurized milk. We performed a crossover trial involving 16 adults with self-reported lactose intolerance and lactose malabsorption confirmed by hydrogen (H2) breath testing. Participants underwent 3, 8-day milk phases (raw vs 2 controls: pasteurized, soy) in randomized order separated by 1-week washout periods. On days 1 and 8 of each phase, milk consumption was 473 mL (16 oz); on days 2 to 7, milk dosage increased daily by 118 mL (4 oz), beginning with 118 mL (4 oz) on day 2 and reaching 710 mL (24 oz) on day 7. Outcomes were area under the breath H2 curve (AUC H2) and self-reported symptom severity (visual analog scales: flatulence/gas, audible bowel sounds, abdominal cramping, diarrhea). AUC H2 (mean ± standard error of the mean) was higher for raw vs pasteurized on day 1 (113 ± 21 vs 71 ± 12 ppm·min·10(-2), respectively, P = .01) but not day 8 (72 ± 14 vs 74 ± 15 ppm·min·10(-2), respectively, P = .9). Symptom severities were not different for raw vs pasteurized on day 7 with the highest dosage (P >.7). AUC H2 and symptom severities were higher for both dairy milks compared with soy milk. Raw milk failed to reduce lactose malabsorption or lactose intolerance symptoms compared with pasteurized milk among adults positive for lactose malabsorption. These results do not support widespread anecdotal claims that raw milk reduces the symptoms of lactose intolerance.
-
RESEARCH OF BIOTRANSFORMATION PROCESS OF CONTAINING SUGAR RAW FOR ISOMALTULOSE RECEIVING
Directory of Open Access Journals (Sweden)
O. S. Korneeva
2014-01-01
Full Text Available The process of biotransformation containing sugar raw isomaltulosesynthase bacteria of the genus Erwinia to produce isomaltulose - natural sugars substitute. Raw cane sugar, beet molasses and sweet sorghum syrup used for isomaltulose. It was established that cane sugar may serve as a substrate for the enzymatic reaction together with biotransformation of pure sucrose. Yield of isomaltulose in the transformation of raw sugar was comparable to the control and was 97% for 3,5 hours at the optimal isomerization conditions (pH 6,0, 30 º C, the enzyme dosage of 5 U / mg of sucrose. Scientifically substantiated reasons for reducing the degree of transformation of molasses, sugar syrup strength sorghum. The influence of non-sugars accompanying basic substrates - raw cane sugar, molasses, sweet sorghum syrup, when biocatalytic transformation. Proved inhibitory effect of metal ion (aluminum , iron , anions of inorganic acids ( nitrate , chloride, phosphate , amino acids (serine , aspartic acid -hand , organic acids ( citric acid, acetic acid, the process of biotransformation , the formation of sucrose. Reducing the degree of isomerization in the presence of sucrose was observed in the study of non-sugars from 50 to 65 % compared with the control. Isomaltulosesynthase activating effect on , and consequently , the yield of isomaltulose to set calcium and manganese in the form of their sulfates. The introduction of these components into a solution of pure sucrose increases the yield of isomaltulose by 30.5 and 13.2 % respectively. The data obtained will be the basis of studies to optimize the process of biotransformation of various sources of vegetable raw materials rich in sucrose to produce isomaltulose.
-
Raw materials resources classification and characterisation for ...
African Journals Online (AJOL)
Raw materials resources classification and characterisation for ceramic tableware production in Nigeria. PSA Irabor. Abstract. No Abstract. Journal of Applied Science, Engineering and Technology Vol. 2(1) 2002: 48-52. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT.
-
Improvement of raw starch digestibility by ion-beam mutation of Aspergillus awamori
Energy Technology Data Exchange (ETDEWEB)
Amsal, Aryanti [National Atomic Energy Agency, Jakarta (Indonesia); Takigami, Machiko; Ito, Hitoshi
1998-09-01
Aspergillus awamori possess the ability to express raw starch digestibility. For the effective utilization of starchy crops produced in South-Asian countries, it is important to achieve the digestion of raw starchs for industrial fermentation process. In this study, higher ratio of mutant strains of Aspergillus awamori IFO4033 were isolated by irradiation of C{sup 5+} ion-beam on freeze dried spores with improvement of enzyme production for two-to threefold in the extracellular {alpha}-amylase compared with gamma-irradiation. The digestibility of raw starch from cassava, sago and sukun increased remarkably about two-to threefold by some mutant strains obtained from irradiation of C{sup 5+} ion-beam. (author)
-
Globalization and its influence to the availability of the Raw material sources
Directory of Open Access Journals (Sweden)
Vodzinský Vladimír
2002-12-01
Full Text Available Process of globalization does not lead only to concentration of physical and financial capital, and to centralization of its managing, what can be considered as its main signs, but at same time it gives whole raw of new claims to realization of technologies and their material basis.One of very important claims is also change in structure and volume of raw materials, that is gradually viewing in increased change from consumption of so-called classical raw materials, without which it is not possible to create basic components of information technologies.Information technologies are then creating important basis for quickly developed new branches of economy.
-
Improvement of raw starch digestibility by ion-beam mutation of Aspergillus awamori
International Nuclear Information System (INIS)
Amsal, Aryanti; Takigami, Machiko; Ito, Hitoshi
1998-01-01
Aspergillus awamori possess the ability to express raw starch digestibility. For the effective utilization of starchy crops produced in South-Asian countries, it is important to achieve the digestion of raw starchs for industrial fermentation process. In this study, higher ratio of mutant strains of Aspergillus awamori IFO4033 were isolated by irradiation of C 5+ ion-beam on freeze dried spores with improvement of enzyme production for two-to threefold in the extracellular α-amylase compared with gamma-irradiation. The digestibility of raw starch from cassava, sago and sukun increased remarkably about two-to threefold by some mutant strains obtained from irradiation of C 5+ ion-beam. (author)
-
DEFF Research Database (Denmark)
Andersen, S. R.; Saadbye, P.; Shukri, Naseer Mahmoud
2006-01-01
Campylobacter jejuni isolated from raw poultry meat collected at retail shops in Denmark in the period 1996-2003 were tested for susceptibility to seven antimicrobial agents. The food samples consisted of raw chicken meat and other raw poultry meat of domestic or imported origin. The highest levels...... for chloramphenicol, nalidixic acid and ciprofloxacin (P food animals....... Monitoring of the occurrence of antimicrobial resistance in C. jejuni isolated from raw uncooked poultry has been performed on a yearly basis since 1996, thus providing useful insight into consumer exposure to antimicrobial-resistant C. jejuni....
-
Current problems of raw fish material processing while manufacturing dried products
Directory of Open Access Journals (Sweden)
Yashonkov A. A.
2017-09-01
Full Text Available The substantiation for using techniques of fish raw material canning has been presented, raw fish being caught or farmed in aquaculture. The main problems in raw fish canning have been reviewed, including significant reduction in thermolabile vitamins in the ultimate product as compared with the raw material due to the thermal processing. Promising canning technique – vacuum drying – has been proposed. This technique makes possible to reduce the temperature of thermal processing down to 50…55 °С and significantly enlarge preservation of thermolabile vitamins from the raw fish. Sampling of raw materials, semi-finished products, finished products, including preparation for analysis has been conducted by standard methods. Disadvantages of this way have been found, it is low energy efficiency of the process. The way to intensify the vacuum drying of aquatic organisms has been proposed based on the method of preliminary pore-forming due to augmenting the area of moisture evaporation. The design of the pilot plant has been proposed in order to research the process of pore forming and vacuum drying. Target species for processing have been suggested. They are as follows: Azov goby (fillet for food products and Black Sea sprat for feeds. The recipes of the feed mixture for granulated floating food for trout have been developed. The results of the first series of the pilot research have been provided. The experiments have proved that preliminary pore forming immediately before vacuum drying makes possible to enlarge the surface area of moisture evaporation by 15…25 %. By processing photomicrographs of sections by means of a special software the authors have got the results demonstrating that when manufacturing dried products by pore forming and drying under pressure 10 kPa the pore take 35...38 % of the inner volume of the product and with drying under pressure 10 kPa – only 18...21 %, and when drying under the atmospheric pressure – 11...13 %.
-
Design and Development of Black Box for Analyzing Accidents in Indian Railways
Directory of Open Access Journals (Sweden)
Alka DUBEY
2010-03-01
Full Text Available Black box also known as engine data recorder (EDR is a device for recording and analyzing train engine status for generation a report and analyzing train accidents. EDR is an application of embedded systems based on sensors, microcontroller, memory, serial interface and display unit. In the present paper designing of EDR with their technical specifications is provided. There railway electric engine WAP-7 is used in present study.
-
Directory of Open Access Journals (Sweden)
TOMÁŠ IFKA
2012-03-01
Full Text Available The influence of CaO and P2O5 upon the reactivity of cement raw meal was investigated in this paper. Ash of bone meal containing Ca3(PO42 - 3CaO·P2O5 was used as the source of P2O5. Two series of samples with different content of the ash of bone meal were prepared. In the first series, the ash of bone was added into cement raw meal. The second series of samples were prepared by considering ash as one of CaO sources. Therefore, the total content of CaO in cement raw meal was kept constant, while the amount of P2O5 increased. These different series of samples were investigated by analyzing free lime content in the clinkers. The XRD analysis and Electron Micro Probe Analyzer analysis of the clinkers were also carried out. Two parameters were used to characterize the reactivity of cement raw meal: content of free lime and Burnability Index (BI calculated from free lime content in both series of samples burnt at 1350 ºC, 1400 ºC, 1450 ºC and 1500 ºC. According to the first parameter, P2O5 content that drastically makes worse the reactivity of cement raw meal was found at 1.11 wt.% in the first series, while this limit has reached 1.52 wt.% in the second one. According to the BI, the limit of P2O5 was found at 1.42 wt. % in the first series and 1, 61 wt.% in the second one. Furthermore, EPMA has demonstrated the presence of P2O5 in both calcium silicate phases forming thus solid solutions.
-
THE COMPRESSIVE AND FLEXURAL STRENGTHS OF SELF-COMPACTING CONCRETE USING RAW RICE HUSK ASH
Directory of Open Access Journals (Sweden)
MD NOR ATAN
2011-12-01
Full Text Available This study investigates the compressive and flexural strengths of self-compacting concrete incorporating raw rice husk ash, individually and in combination with other types of mineral additives, as partial cement replacement. The additives paired with raw rice husk ash were fine limestone powder, pulverized fuel ash and silica fumes. The mix design was based on the rational method where solid constituents were fixed while water and superplasticizer contents were adjusted to produce optimum viscosity and flowability. All mixes were designed to achieve SF1 class slump-flow with conformity criteria ≥ 520 mm and ≤ 700 mm. Test results show that 15% replacement of cement using raw rice husk ash produced grade 40 concrete. It was also revealed that 30% and 45% cement replacements using raw rice husk ash combined with limestone powder and raw rice husk ash combined with limestone powder and silica fume respectively, produced comparable compressive strength to normal concrete and improved flexural strengths.
-
Qualification Methods of Al2O3 Injection Molding Raw Materials
International Nuclear Information System (INIS)
Egész, Á; Gömze, L A
2015-01-01
For producing ceramic arc tube parts (plugs), there are used two different major components for producing injection molding raw material (feedstock): high purity alumina powder as the main component, and an organic paraffin wax as a binder material. It is expressly important to know the material, physical and chemical properties of these components, since mainly these have effect on the homogenity of feedstock, and therefore on the quality of end product. In this research, both of the main components and the moldable raw material was investigated by visual, physical, and thermal methods. As most important and main statement, the researchers found that the dynamic viscosity of raw material depends more on the applied temperature, than on the deformation speed gradient.Applied analitycal methods were laser granulometry, sieve analysis, differential thermal analysis and rheology analysis. (paper)
-
Effects of home-made boiling of bovine raw milk on its microbiological quality
Directory of Open Access Journals (Sweden)
Giampaolo Colavita
2012-10-01
Full Text Available The consumption of raw milk in Italy is allowed only “after boiling”. The aim of this research was to bet-ter understand how the heat treatment of raw milk performed at home by consumers assures their mi-crobiological safety. 50 samples of raw milk (each sample 500 ml provided to consumers who regularly buy raw milk from self-service automatic vending machines were followed from delivery till to after do-mestic heat treatment. Heating was performed by consumers according to their habits. The 50 samples were exposed to different heat treatments of which the mildest was at 68.5 °C and the most intense was at 97.8 °C before switching off. The average of temperatures used was 89.5 °C and the mode was 93.2 °C. According to the different parameters of heat treatment observed, 35 samples of raw milk and 35 samples of heated milk were selected for microbiological and process indicator analyses. Total Microbial Count (TMC, total and fecal coliforms, Escherichia coli, Staphylococcus aureus and Bacillus cereus loads were determined. E. coli was isolated only from one sample of raw milk. No B. cereus nor S. aure-us were found in all samples. After heat treatment, 4 samples showed a residual TMC ranging between 1,7 CFU/ml and 3,2 CFU/ml, whilst the count of total and fecal coliforms were irrelevant. The test for alkaline phosphatase has showed negative in all samples of heated milk, while the test of lactoperoxi-dase was positive in 3 samples. Results indicated that the microbiological risk attributable to the consumption of home heated raw milk is low, if the consumer applies regularly a good heating process.
-
Use of raw materials in the United States from 1900 through 2014
Matos, Grecia R.
2017-08-22
The economic growth of an industrialized nation such as the United States requires raw materials for construction (buildings, bridges, highways, and so forth), defense, and processing and manufacture of goods and services. Since the beginning of the 20th century, the types and quantities of raw materials used have increased and changed significantly. This fact sheet quantifies the amounts of raw materials (other than food and fuel) that have been used in the U.S. economy annually for a period of 115 years, from 1900 through 2014. It provides a broad overview of the quantity (weight) of nonfood and nonfuel materials used in the economy and illustrates the use and significance of raw nonfuel minerals in particular as building blocks of society.These data have been compiled to help the public and policymakers understand the changing annual flow of raw materials put into use in the United States. Such information can be helpful in assessing the potential effects of materials use on the environment, assessing materials’ intensity of use, and examining the role that these materials play in the economy. The data presented indicate the substitution and shift in materials usage from renewable to nonrenewable materials during the 20th century. The disaggregated quantities by commodity (not shown in this fact sheet) may be tested against supply adequacy and end of life issues.
-
Directory of Open Access Journals (Sweden)
Min Xu
2015-01-01
Full Text Available Areca nut, commonly known locally as Semen Arecae (SA in China, has been used as an important Chinese herbal medicine for thousands of years. The raw SA (RAW is commonly processed by stir-baking to yellow (SBY, stir-baking to dark brown (SBD, and stir-baking to carbon dark (SBC for different clinical uses. In our present investigation, intelligent sensory technologies consisting of computer vision (CV, electronic nose (E-nose, and electronic tongue (E-tongue were employed in order to develop a novel and accurate method for discrimination of SA and its processed products. Firstly, the color parameters and electronic sensory responses of E-nose and E-tongue of the samples were determined, respectively. Then, indicative components including 5-hydroxymethyl furfural (5-HMF and arecoline (ARE were determined by HPLC. Finally, principal component analysis (PCA and discriminant factor analysis (DFA were performed. The results demonstrated that these three instruments can effectively discriminate SA and its processed products. 5-HMF and ARE can reflect the stir-baking degree of SA. Interestingly, the two components showed close correlations to the color parameters and sensory responses of E-nose and E-tongue. In conclusion, this novel method based on CV, E-nose, and E-tongue can be successfully used to discriminate SA and its processed products.
-
Raw materials exploitation in Prehistory of Georgia: sourcing, processing and distribution
Tushabramishvili, Nikoloz; Oqrostsvaridze, Avthandil
2016-04-01
Study of raw materials has a big importance to understand the ecology, cognition, behavior, technology, culture of the Paleolithic human populations. Unfortunately, explorations of the sourcing, processing and distribution of stone raw materials had a less attention until the present days. The reasons of that were: incomplete knowledge of the archaeologists who are doing the late period archaeology (Bronze Age-Medieval) and who are little bit far from the Paleolithic technology and typology; Ignorance of the stone artifacts made on different kind of raw-materials, except flint and obsidians. Studies on the origin of the stone raw materials are becoming increasingly important since in our days. Interesting picture and situation have been detected on the different sites and in different regions of Georgia. In earlier stages of Middle Paleolithic of Djruchula Basin caves the number of basalt, andesite, argillite etc. raw materials are quite big. Since 130 000 a percent of the flint raw-material is increasing dramatically. Flint is an almost lonely dominated raw-material in Western Georgia during thousand years. Since approximately 50 000 ago the first obsidians brought from the South Georgia, appeared in Western Georgia. Similar situation has been detected by us in Eastern Georgia during our excavations of Ziari and Pkhoveli open-air sites. The early Lower Paleolithic layers are extremely rich by limestone artifacts while the flint raw-materials are dominated in the Middle Paleolithic layers. Study of these issues is possible to achieve across chronologies, the origins of the sources of raw-materials, the sites and regions. By merging archaeology with anthropology, geology and geography we are able to acquire outstanding insights about those populations. New approach to the Paleolithic stone materials, newly found Paleolithic quarries gave us an opportunities to try to achieve some results for understanding of the behavior of Paleolithic populations, geology and
-
Directory of Open Access Journals (Sweden)
Gianfranco Piva
2010-01-01
Full Text Available The ban of the meat and bone meal for entering animal diets and the concern of transgenic feeds poses a challenge toanimal nutritionists in Europe. The challenge is to find homegrown protein-rich feedstuffs, making sure no antinutritionalfactors are present which could interfere in the animals’ performance. The raw Pea (Pisum sativum (RP, raw Fababean (Vicia faba, variety minor (RFb and raw Lupin (Lupinus albus, variety multitalia (RL were evaluated as alternativeprotein sources into broiler diets. Six hundred thirty 1d-old Ross male chicks, Marek vaccinated, were randomlyassigned to seven dietary treatments (5 pens per treatment/18 birds per pen. Chicks were floor housed, ad libitum fedisocaloric and isonitrogenous diets and had free access to water. Artificial light was provided 10 h/d. The bulk of the basediet (control diet was corn (48.7%, 56.6% and 57%, solvent-extracted soybean meal (42.8%, 37.3% and 33.4%, cornoil (4.4%, 5.2% and 6.3%, plus synthetic amino acids, minerals, trace minerals and vitamins, respectively for the 1-10d-old, 11-28d-old and 29 to 42d-old growing periods. The RP, RFb and RL entered diets in substitution of the soybeanand corn according to the cost optimization (P100, Fb100 and L100, respectively for RP, RFb and RL and at half of theoptimized quantity (RP50, RFb50 and RL50, respectively for RP, RFb and RL. The amount used as fed basis for the higherlevel of inclusion were: P100: 350 g/kg for all diets; Fb100: 480 g/kg (1-10d-old and 500 g/kg (11-42d-old; L100:360 g/kg (1-10d-old and 300 g/kg (11-42d-old. The average daily gain (ADG were lower (P compared to the control group. Over the whole period of growth, the RFb group had similar ADG compared to the controlgroup and for both levels of inclusion, whereas reduced (P (P growth. Birds performance was improved (P and breast and leg quarter cuts. The RFb and RL could represent valuable protein feeds in broilers diet formulation.
-
Study of mechanoactivation of tungsten-molybdenum containing raw material in gas-jet mill
International Nuclear Information System (INIS)
Agnokov, T.Sh.; Gorobets, L.Zh.; Martynenko, V.P.; Fedorov, Yu.P.; Krakhmaleva, M.T.; Sokolova, L.A.
1988-01-01
Investigation is aimed at intensifying autoclave-soda leaching of tungsten-molybdenum-containing raw material. Connection of reactivity and physicochemical properties of crushed tungsten-molybdenum-containing products under different gas-jet crushing parameters is investigated. Optimal technological indices of hydrometallurgical reprocessing of tungsten-molybdenum-containing raw materials and products processed by gas-jet technique are given. The results obtained point out to perspectiveness of applying gas-jet technique of thermomechanical processing for intensifying and increasing the quality of tungsten- and molybdenum-containing raw materials and products of hydrometallurgical production
-
2010-07-01
... than kilns; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw and finish mills. 63.1348 Section 63.1348 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY...; in-line kiln/raw mills; clinker coolers; new and reconstructed raw material dryers; and raw and...
-
Mishra, S. B.; Langwenya, S. P.; Mamba, B. B.; Balakrishnan, M.
South African coal and coal fly ash were selected as the raw materials to be used for study of their morphology and physicochemical properties and their respective activated carbons for adsorption applications. Coal and fly ash were individually steam activated at a temperature range of 550-1000 °C for 1 h in a muffle furnace using cylindrical stainless steel containers. Scanning electron micrographs revealed a change in surface morphology with more mineral matter available on the surface of the coal particles due to increased devolatilization. However, in the case of fly ash, the macerals coalesced to form agglomerates and the presence of unburnt carbon constituted pores of diameter between 50 and 100 nm. The BET surface area of coal improved significantly from 5.31 to 52.12 m 2/g whereas in case of fly ash the surface area of the raw sample which was originally 0.59 m 2/g and upon activation increased only up to 2.04 m 2/g. The chemical composition of the fly ash confirmed that silica was the major component which was approximately 60% by weight fraction. The impact of this study was to highlight the importance of using raw materials such as coal and a waste product, in the form of coal ash, in order to produce affordable activated carbon that can be used in drinking water treatment. This would therefore ensure that the quality of water supplied to communities for drinking is not contaminated especially by toxic organic compounds.
-
Directory of Open Access Journals (Sweden)
A.A. Moawad
2011-10-01
Full Text Available Milk from different animal species has variable levels of antimicrobial factors against some of spoilage bacteria. For example, they are significantly present in higher concentration in she-camel’s milk than in cattle or buffalo and they are more heat-resistant than their counterparts in cattle and buffalo. Spoilage bacteria are known to communicate with each other by release of signaling molecules, a phenomenon described as quorum sensing (QS. Some food matrices inhibit these signaling compounds. In this study we screened QS inhibitory activities in raw milk of cattle and camel. Ten samples each of fresh raw cow’s milk and she-camel’s milk from apparently healthy animals were screened using the bacterial model Cromobacterium violaceum. The tested cow’s raw milk samples were able to inhibit the production of QS signalling molecules acyl-homoserine lactones (AHLs produced by C. violaceum. However, she-camel’s milk samples were less effective in inhibiting such AHLs. Thus, one of the factors which influence the inhibitory activity could be derived from variation in milk chemical composition, especially in the percentage of fat which is significantly higher in tested cow’s milk samples (2.22±0.12 than in tested she-camel’s milk samples (1.44±0.35. Natural inhibition of QS signaling by cow’s milk may offer a unique means to control foodborne pathogens and reduce microbial spoilage.
-
IMPROVING THE SYSTEM OF RAW MATERIAL SUPPLY OF THE MEAT INDUSTRY
Directory of Open Access Journals (Sweden)
A. M. Bukreev
2013-01-01
Full Text Available The article describes the characteristics of the process of improving the system raw materials supply of meat industry and presents the main factors, criteria, principles and algorithm rational distribution of the meat industry. The relevance of the research topic, in a globalized economy and Russia's accession to the WTO, caused by necessity to improve the system of raw material supply domestic enterprises and enhancing food security.
-
Antibacterial efficacy of raw and commercially available honey
African Journals Online (AJOL)
Administrator
2011-09-19
Sep 19, 2011 ... Key words: Honey, antibacterial activity, raw honey, commercially available honey, minimum inhibitory ... against pathogenic bacteria, oral bacteria as well as food .... explore the possible benefits of the use of honey among.
-
Effect of Raw Milk on Lactose Intolerance: A Randomized Controlled Pilot Study
Mummah, Sarah; Oelrich, Beibei; Hope, Jessica; Vu, Quyen; Gardner, Christopher D.
2014-01-01
PURPOSE This pilot study aimed to determine whether raw milk reduces lactose malabsorption and/or lactose intolerance symptoms relative to pasteurized milk. METHODS We performed a crossover trial involving 16 adults with self-reported lactose intolerance and lactose malabsorption confirmed by hydrogen (H2) breath testing. Participants underwent 3, 8-day milk phases (raw vs 2 controls: pasteurized, soy) in randomized order separated by 1-week washout periods. On days 1 and 8 of each phase, milk consumption was 473 mL (16 oz); on days 2 to 7, milk dosage increased daily by 118 mL (4 oz), beginning with 118 mL (4 oz) on day 2 and reaching 710 mL (24 oz) on day 7. Outcomes were area under the breath H2 curve (AUC ∆H2) and self-reported symptom severity (visual analog scales: flatulence/gas, audible bowel sounds, abdominal cramping, diarrhea). RESULTS AUC ∆H2 (mean ± standard error of the mean) was higher for raw vs pasteurized on day 1 (113 ± 21 vs 71 ± 12 ppm·min·10−2, respectively, P = .01) but not day 8 (72 ± 14 vs 74 ± 15 ppm·min·10−2, respectively, P = .9). Symptom severities were not different for raw vs pasteurized on day 7 with the highest dosage (P >.7). AUC ∆H2 and symptom severities were higher for both dairy milks compared with soy milk. CONCLUSIONS Raw milk failed to reduce lactose malabsorption or lactose intolerance symptoms compared with pasteurized milk among adults positive for lactose malabsorption. These results do not support widespread anecdotal claims that raw milk reduces the symptoms of lactose intolerance. PMID:24615309
-
Energy saving cement production by grain size optimisation of the raw meal
Directory of Open Access Journals (Sweden)
B. Simons
Full Text Available The production of cement clinker is an energy consuming process. At about 50% of the energy is associated with grinding and milling of the raw meal, that normally is in the range 100% <200 μm with 90% <90 μm. Question: is it possible to use coarser components of the raw meal without reducing the clinker quality. With synthetic raw meals of various grain sizes the clinker formation was studied at static (1100 - 1450°C and dynamic conditions (heating microscope. A routine to adjust the grain size of the components for industrial raw meals is developed. The fine fraction <90 μm should mainly contain the siliceous and argileous components, whereas the calcitic component can be milled separately to a grain size between 200-500 μm, resulting in lower energy consumption for milling. Considering the technical and economical realizability the relation fine/coarse should be roughly 1:1. The energy for milling can be reduced significantly, that in addition leads to the preservation of natural energy resources.
-
Lead, cadmium and chromium in raw and boiled portions of Norway lobster.
Perugini, Monia; Visciano, Pierina; Manera, Maurizio; Abete, Maria Cesarina; Tarasco, Renata; Amorena, Michele
2014-01-01
Lead, cadmium and chromium levels were determined in different raw and boiled portions of Norway lobster caught in the central Adriatic Sea (Italy). In raw specimens, the lowest concentrations were always detected in the white meat. Lead and cadmium content in the edible portion never exceeded the maximum levels set by European legislation. The highest cadmium and chromium values (0.47 ± 0.04 and 0.62 ± 0.13 mg/kg wet weight, respectively) were detected in the brown meat, while the highest lead concentrations were found in the exoskeleton (0.21 ± 0.01 mg/kg wet weight). Also, the boiled samples showed the lowest metal levels in the white meat, even if a significant increase (p < 0.01) was found for lead and cadmium compared to the corresponding raw portions. Among metals, chromium showed the highest concentrations in both raw and boiled portions, but up to now, the European legislation did not envisage any limits in seafood.
-
Challenges and Opportunities for Harmonizing Research Methodology: Raw Accelerometry.
van Hees, Vincent T; Thaler-Kall, Kathrin; Wolf, Klaus-Hendrik; Brønd, Jan C; Bonomi, Alberto; Schulze, Mareike; Vigl, Matthäus; Morseth, Bente; Hopstock, Laila Arnesdatter; Gorzelniak, Lukas; Schulz, Holger; Brage, Søren; Horsch, Alexander
2016-12-07
Raw accelerometry is increasingly being used in physical activity research, but diversity in sensor design, attachment and signal processing challenges the comparability of research results. Therefore, efforts are needed to harmonize the methodology. In this article we reflect on how increased methodological harmonization may be achieved. The authors of this work convened for a two-day workshop (March 2014) themed on methodological harmonization of raw accelerometry. The discussions at the workshop were used as a basis for this review. Key stakeholders were identified as manufacturers, method developers, method users (application), publishers, and funders. To facilitate methodological harmonization in raw accelerometry the following action points were proposed: i) Manufacturers are encouraged to provide a detailed specification of their sensors, ii) Each fundamental step of algorithms for processing raw accelerometer data should be documented, and ideally also motivated, to facilitate interpretation and discussion, iii) Algorithm developers and method users should be open about uncertainties in the description of data and the uncertainty of the inference itself, iv) All new algorithms which are pitched as "ready for implementation" should be shared with the community to facilitate replication and ongoing evaluation by independent groups, and v) A dynamic interaction between method stakeholders should be encouraged to facilitate a well-informed harmonization process. The workshop led to the identification of a number of opportunities for harmonizing methodological practice. The discussion as well as the practical checklists proposed in this review should provide guidance for stakeholders on how to contribute to increased harmonization.
-
Use of a new borate raw material for glaze formulation
International Nuclear Information System (INIS)
Gomez-Tena, M. P.; Moreno, A.; Bou, E.; Cook, S.; Galindo, M.
2010-01-01
The Rio Tinto Minerals company has developed a new borate (E-4972), which can be used in glaze formulation (patent WO 2007/148101). This new borate, synthesised by low-temperature calcination, fundamentally contributes five oxides: silicon oxide (SiO 2 ), aluminium oxide (Al 2 O 3 ), boron oxide (B 2 O 3 ), calcium oxide (CaO), and sodium oxide (Na 2 O), its content in B 2 O 3 being between 10 and 11% by weight. It is largely amorphous, and quartz is the major crystalline phase present. The characteristics of this new borate, such as its low solubility and ability readily to form glassy phase, enable it to be used as a raw material in glaze compositions. Its suitability for glaze formulation has been the result of several years research in collaboration with the Instituto de Tecnologia Ceramica. In this paper, the feasibility has been studied of fabricating ceramic glazes by using a new synthetic borate raw material that contributes boron to the glaze composition without this needing to be done in fritted form. It has been possible to obtain fired glazes with similar technical and aesthetics characteristics to those obtained from industrial glaze compositions that contain typical frits in their compositions, thus enabling glazes to be formulated by using the new synthetic boron raw material. The results obtained show that this new raw material (E-4972) is particularly appropriate for use in producing glazes with low gloss at high temperature. (Author) 15 refs.
-
Role of trapped and solvated electrons in Ps formation
International Nuclear Information System (INIS)
Stepanov, S.V.; Byakov, V.M.; Mikhin, K.V.; He, C.; Hirade, T.
2005-01-01
Role of trapped and solvated electrons in Ps formation is discussed. Combination of thermalized positron with such electrons is possible from the view point of the energy balance and may results in Ps formation. This process proceeds during all e = lifetime matter. Fitting of raw experimental e + -e - annihilation spectra has to be based on an adequate physical input, which often leads to necessity of nonexponential deconvolution of the spectra. We have interpreted the Ps formation data in polyethylene, ethylene-methylmethacrylate and polymethylmethacrylate in dark and in light vs. tome of the measurement and temperature. parameters characterized accumulation of trapped electrons and their recombination with counter ions and positrons are obtained. (author)
-
Raw Milk Hygiene at Local Markets and Automatic Milk Dispenser Machines
Directory of Open Access Journals (Sweden)
Gheorghe Şteţca
2014-11-01
Full Text Available In Romania, direct sales of raw milk to the final consumer is developed based on the local regulations. These are in accordance to European Regulation that must meet some quality requirements for the total number of germs, somatic cells, without antibiotics, coming from healthy animals who did not suffer from diseases that can be transmitted to humans through milk. Raw milk is sold in Romania in local markets and by automatic milk dispenser machines. Based on these regulations, a study regarding the quality and security to human health of raw milk was conducted on the commercialized milk in local markets and automatic milk dispensers. During May-June 2014 samples of raw milk were collected from Cluj-Napoca local markets and automatic milk dispensers. All samples were kept to refrigeration conditions until the moment of analyze which took place at the sampling day. The following parameters were taken into account: fat content, protein, casein, lactose, nonfat dry matter, pH, milk freezing point, added water, antibiotics residues, milk urea, number of germ cells and somatic cells. All obtained results were verified by the validated methods applied. Our research can be forward conducted in order to verify the hygiene and composition of milk from the whole dairy chain.
-
Proteolysis produced within biofilms of bacterial isolates from raw milk tankers.
Teh, Koon Hoong; Flint, Steve; Palmer, Jon; Andrewes, Paul; Bremer, Phil; Lindsay, Denise
2012-06-15
In this study, six bacterial isolates that produced thermo-resistant enzymes isolated from the internal surfaces of raw milk tankers were evaluated for their ability to produce proteolysis within either single culture biofilms or co-culture biofilms. Biofilms were formed in an in vitro model system that simulated the upper internal surface of a raw milk tanker during a typical summer's day of milk collection in New Zealand. The bacterial isolates were further evaluated for their ability to form biofilms at 25, 30 and 37°C. Mutual and competitive effects were observed in some of the co-culture biofilms, with all isolates being able to form biofilms in either single culture or co-culture at the three temperatures. The proteolysis was also evaluated in both biofilms and corresponding planktonic cultures. The proteolysis per cell decreased as the temperature of incubation (20-37°C) increased. Furthermore, mutualistic interactions in terms of proteolysis were observed when cultures were grown as co-culture biofilms. This is the first study to show that proteolytic enzymes can be produced in biofilms on the internal surfaces of raw milk tankers. This has important implications for the cleaning and the temperature control of raw milk transport tankers. Copyright © 2012 Elsevier B.V. All rights reserved.
-
Medeiros, Diane T; Sattar, Syed A; Farber, Jeffrey M; Carrillo, Catherine D
2008-10-01
The occurrence of Campylobacter spp. in a variety of foods from Ottawa, Ontario, Canada, and raw milk samples from across Canada was determined over a 2-year period. The samples consisted of 55 raw foods (chicken, pork, and beef), 126 raw milk samples from raw milk cheese manufacturers, and 135 ready-to-eat foods (meat products, salads, and raw milk cheeses). Campylobacter jejuni was detected in 4 of the 316 samples analyzed: 1 raw beef liver sample and 3 raw chicken samples. An isolation rate of 9.7% was observed among the raw chicken samples tested. This study also investigated the role of cross-contamination in disseminating Campylobacter from raw poultry within a food service operation specializing in poultry dishes. Accordingly, kitchen surfaces within a restaurant in Ottawa, Ontario, were sampled between March and August 2001. Tests of the sampling method indicated that as few as 100 Campylobacter cells could be detected if sampling was done within 45 min of inoculation; however, Campylobacter spp. were not detected in 125 swabs of surfaces within the kitchens of this food service operation. Despite the reported high prevalence of Campylobacter spp. in raw poultry, this organism was not detected on surfaces within a kitchen of a restaurant specializing in poultry dishes.
-
Apparatus comprising trace element dosage and method for treating raw water in biofilter
DEFF Research Database (Denmark)
2015-01-01
the inlet (2) to the outlet (3) or in the reverse direction, - the trace element dosage device (13) is positioned upstream of the porous filter material and microbial biomass and is configured to dose trace element(s) to the water flowing through the filter. A method for treating raw water by microbial......Apparatus for treating raw water in a biofilter The present invention relates to an apparatus in which raw water is treated through microbial activity where microbial activity is controlled by nutrients and other parameters. Some of the nutrients controlling the microbial activity are trace...... elements such as certain metals (Cu, Co, Cr, Mo, Ni, W, Zn or a mixture thereof). The apparatus comprising - a volume provided with an inlet (2) for raw water and an outlet (3) for water having been subjected to microbial activity, a filter and a trace element dosage device (13) are placed in this volume...
-
Occurrence of 1,4-dioxane in cosmetic raw materials and finished cosmetic products.
Black, R E; Hurley, F J; Havery, D C
2001-01-01
Surveys of cosmetic raw materials and finished products for the presence of the carcinogen 1,4-dioxane have been conducted by the U.S. Food and Drug Administration since 1979. Analytical methods are described for the determination of 1,4-dioxane in ethoxylated cosmetic raw materials and cosmetic finished products. 1,4-Dioxane was isolated by azeotropic atmospheric distillation and determined by gas chromatography using n-butanol as an internal standard. A solid-phase extraction procedure based on a previously published method for the determination of 1,4-dioxane in cosmetic finished products was also used. 1,4-Dioxane was found in ethoxylated raw materials at levels up to 1410 ppm, and at levels up to 279 ppm in cosmetic finished products. Levels of 1,4-dioxane in excess of 85 ppm in children's shampoos indicate that continued monitoring of raw materials and finished products is warranted.
-
A concept to standardize raw biosignal transmission for brain-computer interfaces.
Breitwieser, Christian; Neuper, Christa; Müller-Putz, Gernot R
2011-01-01
With this concept we introduced the attempt of a standardized interface called TiA to transmit raw biosignals. TiA is able to deal with multirate and block-oriented data transmission. Data is distinguished by different signal types (e.g., EEG, EOG, NIRS, …), whereby those signals can be acquired at the same time from different acquisition devices. TiA is built as a client-server model. Multiple clients can connect to one server. Information is exchanged via a control- and a separated data connection. Control commands and meta information are transmitted over the control connection. Raw biosignal data is delivered using the data connection in a unidirectional way. For this purpose a standardized handshaking protocol and raw data packet have been developed. Thus, an abstraction layer between hardware devices and data processing was evolved facilitating standardization.
-
Effects of inulin, carrot and cellulose fibres on the properties of raw ...
African Journals Online (AJOL)
The effects of inulin, carrot, and cellulose fibres (3%, 6%, and 9%) on raw and fried chicken meatballs were studied. Meatball pH, thiobarbituric acid reactive substances (TBARS), and colour values were determined for raw samples in refrigerated storage on the 1st, 5th and 10th days. The effects of fibres and their various ...
-
Bacteriophages safely reduce Salmonella contamination in pet food and raw pet food ingredients.
Soffer, Nitzan; Abuladze, Tamar; Woolston, Joelle; Li, Manrong; Hanna, Leigh Farris; Heyse, Serena; Charbonneau, Duane; Sulakvelidze, Alexander
2016-01-01
Contamination of pet food with Salmonella is a serious public health concern, and several disease outbreaks have recently occurred due to human exposure to Salmonella tainted pet food. The problem is especially challenging for raw pet foods (which include raw meats, seafood, fruits, and vegetables). These foods are becoming increasingly popular because of their nutritional qualities, but they are also more difficult to maintain Salmonella -free because they lack heat-treatment. Among various methods examined to improve the safety of pet foods (including raw pet food), one intriguing approach is to use bacteriophages to specifically kill Salmonella serotypes. At least 2 phage preparations (SalmoFresh® and Salmonelex™) targeting Salmonella are already FDA cleared for commercial applications to improve the safety of human foods. However, similar preparations are not yet available for pet food applications. Here, we report the results of evaluating one such preparation (SalmoLyse®) in reducing Salmonella levels in various raw pet food ingredients (chicken, tuna, turkey, cantaloupe, and lettuce). Application of SalmoLyse® in low (ca. 2-4×10 6 PFU/g) and standard (ca. 9×10 6 PFU/g) concentrations significantly ( P contamination in all raw foods examined compared to control treatments. When SalmoLyse®-treated (ca. 2×10 7 PFU/g) dry pet food was fed to cats and dogs, it did not trigger any deleterious side effects in the pets. Our data suggest that the bacteriophage cocktail lytic for Salmonella can significantly and safely reduce Salmonella contamination in various raw pet food ingredients.
-
Mineral raw materials for power production in legislation of the Republic of Croatia
International Nuclear Information System (INIS)
Matisa, Z.
1999-01-01
According to the Constitution of the Republic of Croatia, mineral wealth is a public good of legal interest to the Republic of Croatia and enjoys its special protection. The Mining Law establishes that mineral wealth (including mineral resources that are used for power production) is the property of the Republic of Croatia. Among other mineral raw materials, this refers to mineral raw materials that are used for power production: coal, oil, natural gas, radioactive mineral raw materials and geothermal waters. These mineral resources are as almost all other mineral raw materials with the exception of geothermal waters, an unrecoverable natural resource. The right to use that natural resource may be granted only by a concession. The mining legislation provides for exploration and exploitation of mineral raw materials. Exploration of oil and gas is considered to comprise operations and testing with the aim to establish the existence, position and form of oil and natural gas deposits, their quality and quantity, as well as exploitation conditions. Exploitation of oil and natural gas is considered to comprise extraction from deposits, refining and transport, as well as disposal in geological structures. Mineral raw materials used in power production amount to 63% of national total primary energy production, and they cover 33% of total power consumption in the country. Legislation in the Republic of Croatia, which refers to exploration and exploitation of oil and natural gas, allows economic utilization of that unrecoverable natural wealth to run smoothly and in compliance with practices in our European environment. (author)
-
Molds contamination of raw milk and dairy products: Occurrence, diversity and contamination source
Directory of Open Access Journals (Sweden)
T Moshtaghi Maleki
2015-11-01
Full Text Available This study aimed to assess the occurrence and diversity of mold species in raw milk and its products along with the identification of potential contamination sources. For this reason, a total of 260 samples consisting of 80 raw milk, 100 dairy products (i.e., pasteurized milk, yoghurt, cheese and buttermilk and 80 environmental (i.e. ingredients, packaging materials, surface of processing equipments and air specimens were collected. Using culture assay and microscopic observation, the occurrence as well as the diversity of mold species was investigated. According to the results, 82.3% of the samples were identified as positive for mold contamination. The percentage of mold contamination for raw milk was estimated as 97.5%. In the case of pasteurized milk, yoghurt, buttermilk, cheese and environmental samples, it was determined as 52%, 76%, 52%, 56% and 96.25%, respectively. Mold diversity among various samples consisted of Aspergillus, Geotrichum, Penicillium, Mucor, Alternaria, Rhizopus, Stemphylium, Cladosporium, and Fusarium. Results revealed a significant (p < 0.01 correlation between kind of mold species isolated from raw milk and dairy products. Similarly, a correlation was observed between dairy products and environmental sources. Regarding the high occurrence of mold contamination in raw milk and environmental sources, it seems that in some instances heat treatment was not effective enough to inactivate all molds; whereas in some other cases, cross contamination may have resulted in mold contamination. Therefore, it is crucial to maintain hygienic conditions during raw milk handling as well as processing steps. These practices could efficiently reduce the occurrence of mold contaminations in dairy products.
-
International Nuclear Information System (INIS)
Mello, Roberta Monteiro de
2006-01-01
In order to decrease environmental impact, caused by mud discarding and clay extraction in the ceramic industry, it was used residual mud from marble and granite companies for structural ceramic. Samples were collected in twelve different marble companies located at the metropolitan region of Sao Paulo. However, only four samples were selected, based on its different characteristics. Clay stone was the raw material chosen to prepare the structural ceramic, considering its high use in this segment. Samples and clay stone were both analysed by the following procedures: granulometric analysis, x-rays fluorescent chemical analysis and x-rays diffraction mineralogical analysis, besides, tests in the samples were conducted following NBR 10004 standards. Once raw materials were characterized, the plasticity test was conducted. Test specimen were molded with different levels of mud, then burned and submitted to technological tests, such as: mechanical resistance, water absorption, porosity, specific gravity and retraction, material dilation before burning process and scanning electron microscopy. The final results have shown the viability of using this kind of mud, and pointed some advantages on its usage, but taking in consideration some previous conditions to be adopted. (author)
-
Energy Technology Data Exchange (ETDEWEB)
1980-01-01
Part 1-4 of the series ''The basis of raw materials supply'' is intended to bring about a better understanding of the ''Concept for the supply of Austria with mineral raw- and primary materials''. Part 3 deals with recovery of raw material from old- and waste material as an important contribution to an extension of the supply's basis and to an improvement of raw material utilization.
-
A Kind of Single-frequency Precise Point Positioning Algorithm Based on the Raw Observations
Directory of Open Access Journals (Sweden)
WANG Li
2015-01-01
Full Text Available A kind of single-frequency precise point positioning (PPP algorithm based on the raw observations is presented in this paper. By this algorithm, the ionospheric delays were corrected efficiently by means of adding the ionospheric delay prior information and the virtual observation equations with the spatial and temporal constraints, and they were estimated as the unknown parameters simultaneously with other positioning parameters. Then, a dataset of 178 International GNSS Service (IGS stations at day 72 in 2012 was used to evaluate the convergence speed, the positioning accuracy and the accuracy of the retrieved ionospheric VTEC. The series of results have shown that the convergence speed and stability of the new algorithm are much better than the traditional PPP algorithm, and the positioning accuracy of about 2-3 cm and 2-3 dm can be achieved respectively for static and kinematic positioning with the single-frequency observations' daily solution. The average bias of ionospheric total electron content retrieved by the single-frequency PPP and dual-frequency PPP is less than 5 TECU. So the ionospheric total electron content can be used as a kind of auxiliary products in GPS positioning.
-
Directory of Open Access Journals (Sweden)
Loes M. J. Kroon-Batenburg
2017-01-01
Full Text Available A topical review is presented of the rapidly developing interest in and storage options for the preservation and reuse of raw data within the scientific domain of the IUCr and its Commissions, each of which operates within a great diversity of instrumentation. A résumé is included of the case for raw diffraction data deposition. An overall context is set by highlighting the initiatives of science policy makers towards an `Open Science' model within which crystallographers will increasingly work in the future; this will bring new funding opportunities but also new codes of procedure within open science frameworks. Skills education and training for crystallographers will need to be expanded. Overall, there are now the means and the organization for the preservation of raw crystallographic diffraction data via different types of archive, such as at universities, discipline-specific repositories (Integrated Resource for Reproducibility in Macromolecular Crystallography, Structural Biology Data Grid, general public data repositories (Zenodo, ResearchGate and centralized neutron and X-ray facilities. Formulation of improved metadata descriptors for the raw data types of each of the IUCr Commissions is in progress; some detailed examples are provided. A number of specific case studies are presented, including an example research thread that provides complete open access to raw data.
-
International Nuclear Information System (INIS)
Kroon-Batenburg, Loes M. J.; Helliwell, John R.; McMahon, Brian; Terwilliger, Thomas Charles
2017-01-01
A topical review is presented of the rapidly developing interest in and storage options for the preservation and reuse of raw data within the scientific domain of the IUCr and its Commissions, each of which operates within a great diversity of instrumentation. A résumé is included of the case for raw diffraction data deposition. An overall context is set by highlighting the initiatives of science policy makers towards an 'Open Science' model within which crystallographers will increasingly work in the future; this will bring new funding opportunities but also new codes of procedure within open science frameworks. Skills education and training for crystallographers will need to be expanded. Overall, there are now the means and the organization for the preservation of raw crystallographic diffraction data via different types of archive, such as at universities, discipline-specific repositories (Integrated Resource for Reproducibility in Macromolecular Crystallography, Structural Biology Data Grid), general public data repositories (Zenodo, ResearchGate) and centralized neutron and X-ray facilities. Formulation of improved metadata descriptors for the raw data types of each of the IUCr Commissions is in progress; some detailed examples are provided. Lastly, a number of specific case studies are presented, including an example research thread that provides complete open access to raw data.
-
Gaya, Pilar; Sánchez, Carmen; Nuñez, Manuel; Fernández-García, Estrella
2005-08-01
Changes in nitrogen compounds during ripening of 40 batches of Manchego cheese made from raw milk (24 batches) or pasteurized milk (16 batches) at five different dairies throughout the year were investigated. After ripening for six months, degradation of p-kappa- and beta-caseins was more intense in raw milk cheese and degradation of alpha(s2)-casein in pasteurized milk cheese. Milk pasteurization had no significant effect on breakdown of alpha(s1)-casein. Hydrophobic peptide content did not differ between raw and pasteurized milk cheese, whereas hydrophilic peptide content was higher in raw milk cheese. There were no significant differences between seasons for residual caseins, but hydrophobic peptides were at a higher level in cheese made in autumn and winter and hydrophilic peptides in cheese made in winter and spring. Raw milk cheese had a higher content of total free amino acids and of most individual free amino acids than pasteurized milk cheese. The relative percentages of the individual free amino acids were significantly different for raw milk and pasteurized milk cheeses. The relative percentages of Lys and lie increased, while those of Val, Leu and Phe decreased during ripening. There were also seasonal variations within the relative percentages of free amino acids. In raw milk cheeses, Asp and Cys were relatively more abundant in those made in autumn, Glu and Arg in cheeses made in winter, and Lys and Ile in cheeses made in spring and summer. Biogenic amines were detected only in raw milk cheese, with the highest levels of histamine, tryptamine and tyramine in cheeses made in spring, winter and spring, respectively.
-
Material Classification Using Raw Time-of-Flight Measurements
Su, Shuochen; Heide, Felix; Swanson, Robin J.; Klein, Jonathan; Callenberg, Clara; Hullin, Matthias; Heidrich, Wolfgang
2016-01-01
We propose a material classification method using raw time-of-flight (ToF) measurements. ToF cameras capture the correlation between a reference signal and the temporal response of material to incident illumination. Such measurements encode unique
-
High levels of whole raw soya beans in dairy cow diets: digestibility and animal performance.
Barletta, R V; Gandra, J R; Freitas Junior, J E; Verdurico, L C; Mingoti, R D; Bettero, V P; Benevento, B C; Vilela, F G; Rennó, F P
2016-12-01
The aim of this study was to evaluate the effects of high levels of whole raw soya beans in the diets of lactating cows. Twelve Holstein dairy cows were used, randomized in three 4 × 4 balanced and contemporary Latin squares and fed the following diets: (i) control (C), without including whole raw soya beans; (ii) 80 g/kg in DM of whole raw soya beans (G80); (iii) 160 g/kg in DM of whole raw soya beans (G160); and (iv) 240 g/kg in DM of whole raw soya beans (G240). There was significant reduction (p beans in dairy cow diets improves the unsaturated fatty acid profile in milk, and the diets (G80 and G160) led to minor alterations in the digestive processes and animal metabolism. Journal of Animal Physiology and Animal Nutrition © 2015 Blackwell Verlag GmbH.
-
International Nuclear Information System (INIS)
Thayer, D.W.; Boyd, G.; Kim, A.; Fox, J.B. Jr.; Farrell, H.M. Jr.
1998-01-01
The radiation resistance and ability of Listeria monocytogenes ATCC 7644, 15313, 43256, and 49594 to multiply on irradiated, air-packed, refrigerated raw or cooked turkey breast meat nuggets (ca. 25 g) and ground turkey breast meat was investigated. Gamma-radiation D values for L. monocytogenes were significantly different on raw and cooked nuggets, 0.56 +/- 0.03 kGy and 0.69 +/- 0.03 kGy, respectively; but they were not significantly different (P less than or equal to 0.05) on raw and cooked ground turkey meat. High populations (approximately 10(9) CFU/g) of L. monocytogenes declined during 14 days of storage at 4 degrees C in both irradiated and nonirradiated samples of raw but not of cooked ground turkey breast meat. A moderate inoculum (approximately 10(3) CFU/g) did not survive a radiation dose of 3 kGy. The population increased in cooked but not in raw samples of irradiated ground turkey meat stored at either 2 or 7 degrees C for 21 days. The D value changed significantly from 0.70 +/- 0.04 to 0.60 +/- 0.02 kGy when the product was cooked to an internal temperature of 80 degrees C before irradiation. Growth on either raw or cooked turkey meat did not alter the radiation resistance of L. monocytogenes. Analyses were performed for pH, a(w), moisture, and reducing potential of raw and cooked turkey meat and for pH, amino acid profile, thiamine, and riboflavin contents of aqueous extracts of raw and cooked turkey meats without identifying the factor or factors involved in differences in the survival and multiplication of L. monocytogenes on raw and cooked meat
-
Radiotracer investigation of cement raw meal homogenizers. Pt. 2
International Nuclear Information System (INIS)
Baranyai, L.
1983-01-01
Based on radioisotopic tracer technique a method has been worked out to study the homogenization and segregation processes of cement-industrial raw meal homogenizers. On-site measurements were carried out by this method in some Hungarian cement works to determine the optimal homogenization parameters of operating homogenizers. The motion and distribution of different raw meal fractions traced with 198 Au radioisotope was studied in homogenization processes proceeding with different parameters. In the first part of the publication the change of charge homogenity in time was discussed which had been measured as the resultant of mixing and separating processes. In the second part the parameters and types of homogenizers influencing the efficiency of homogenization have been detailed. (orig.) [de
-
Radiotracer investigation of cement raw meal homogenizers. Pt. 2
Energy Technology Data Exchange (ETDEWEB)
Baranyai, L
1983-12-01
Based on radioisotopic tracer technique a method has been worked out to study the homogenization and segregation processes of cement-industrial raw meal homogenizers. On-site measurements were carried out by this method in some Hungarian cement works to determine the optimal homogenization parameters of operating homogenizers. The motion and distribution of different raw meal fractions traced with /sup 198/Au radioisotope was studied in homogenization processes proceeding with different parameters. In the first part of the publication the change of charge homogenity in time was discussed which had been measured as the resultant of mixing and separating processes. In the second part the parameters and types of homogenizers influencing the efficiency of homogenization have been detailed.
-
Raw or Nonpasteurized Products Can Make You Sick
Centers for Disease Control (CDC) Podcasts
2012-03-05
Dr. Adam Langer, CDC epidemiologist, discusses the dangers of consuming raw or nonpasteurized dairy products. Created: 3/5/2012 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID). Date Released: 3/5/2012.
-
MODIS/Aqua Raw Radiances in Counts 5-Min L1A Swath V006
National Aeronautics and Space Administration — The MODIS/Aqua Raw Radiances in Counts 5-Min L1A Swath (MYD01) product contains reformatted and packaged raw instrument data. MODIS instrument data, in packetized...
-
Strontium-90 and cesium-137 in raw milk
International Nuclear Information System (INIS)
1979-01-01
Under the commission of Science and Technology Agency, prefectural public health laboratories and institutes and Japan Chemical Analysis Center have measured the levels of 90 Sr and 137 Cs in milk samples. Sampling was done as follows: 4 times of raw milk samples a year in 10 prefectures for the report to WHO, 2 times of raw milk samples a year in 4 prefectures; and 2 times of city milk samples a year in 29 prefectures. Three litters of fresh milk were collected and carbonated in the prefectural public health laboratories and institutes of each prefecture, and the carbonated samples were collected at Japan Chemical Analysis Center. At Japan Chemical Analysis Center, these collected samples were radiochemically analysed for 90 Sr and 137 Cs using the method applied for the analysis of the radionuclides contents in total diet materials. (author)
-
Sadhukhan, Jhuma; Joshi, Nimisha; Shemfe, Mobolaji; Lloyd, Jonathan R
2017-09-01
Magnetite nanoparticles (MNPs) have several applications, including use in medical diagnostics, renewable energy production and waste remediation. However, the processes for MNP production from analytical-grade materials are resource intensive and can be environmentally damaging. This work for the first time examines the life cycle assessment (LCA) of four MNP production cases: (i) industrial MNP production system; (ii) a state-of-the-art MNP biosynthesis system; (iii) an optimal MNP biosynthesis system and (iv) an MNP biosynthesis system using raw materials sourced from wastewaters, in order to recommend a sustainable raw material acquisition pathway for MNP synthesis. The industrial production system was used as a benchmark to compare the LCA performances of the bio-based systems (cases ii-iv). A combination of appropriate life cycle impact assessment methods was employed to analyse environmental costs and benefits of the systems comprehensively. The LCA results revealed that the state-of-the-art MNP biosynthesis system, which utilises analytical grade ferric chloride and sodium hydroxide as raw materials, generated environmental costs rather than benefits compared to the industrial MNP production system. Nevertheless, decreases in environmental impacts by six-fold were achieved by reducing sodium hydroxide input from 11.28 to 1.55 in a mass ratio to MNPs and replacing ferric chloride with ferric sulphate (3.02 and 2.59, respectively, in a mass ratio to MNPs) in the optimal biosynthesis system. Thus, the potential adverse environmental impacts of MNP production via the biosynthesis system can be reduced by minimising sodium hydroxide and substituting ferric sulphate for ferric chloride. Moreover, considerable environmental benefits were exhibited in case (iv), where Fe(III) ions were sourced from metal-containing wastewaters and reduced to MNPs by electrons harvested from organic substrates. It was revealed that 14.4 kJ and 3.9 kJ of primary fossil resource
-
International Nuclear Information System (INIS)
Alekseeva, E.A.; Volkovich, A.G.; Koba, G.I.; Liksonov, V.I.; Stepanov, V.E.; Tyurin, A.S.; Urutskoev, L.I.; Chesnokov, A.V.
1989-01-01
With the aim of determination of the angular distribution of the gamma-radiation (GR) exposure dose rate (EDR) around the Ukrytie Object (UO) are described the measurement results of GR EDR in July 1988 at the territory, adjoining to UO. The conclusion is made that the main contribution into EDR ensures GR, scattered as a result of the Compton effect on air molecules and that the contribution of the NPP territory is small. 10 figs.; 3 tabs
-
International Nuclear Information System (INIS)
Vega R, J. L.; Cayllahua, F.; Apaza, D. G.; Javier, H.
2015-10-01
Percentage depth dose curves were obtained with TLD-100 dosimeters, EDR2 films and Penelope simulation at the interfaces in an inhomogeneous mannequin, composed by equivalent materials to the human body built for this study, consisting of cylindrical plates of solid water-bone-lung-bone-solid water of 15 cm in diameter and 1 cm in height; plates were placed in descending way (4-2-8-2-4). Irradiated with Co-60 source (Theratron Equinox-100) for small radiation fields 3 x 3 cm 2 and 1 x 1 cm 2 at a surface source distance of 100 cm from mannequin. The TLD-100 dosimeters were placed in the center of each plate of mannequin irradiated at 10 Gy. The results were compared between these measurement techniques, giving good agreement in interfaces better than 97%. This study was compared with the same characteristics of another study realized with other equivalent materials to human body not homogeneous acrylic-bone-cork-bone-acrylic. The percentage depth dose curves were obtained with mini-dosimeters L-alanine of 1 mm in diameter and 3 mm in height and 3.5 to 4.0 mg of mass with spectrometer band K (EPR). The mini-dosimeters were irradiated with a lineal accelerator PRIMUS Siemens 6 MV. The results of percentage depth dose of L-alanine mini-dosimeters show a good agreement with the percentage depth dose curves of Penelope code, better than 97.7% in interfaces of tissues. (Author)
-
Eosinophilic meningitis risk associated with raw Ampullarium canaliculatus snails consumption
Directory of Open Access Journals (Sweden)
Jiun-Jye Wang
2011-05-01
Full Text Available In Taiwan, Angiostrongylus cantonensis infection has been reported in foreign laborers who had consumed raw Ampullarium canaliculatus snails. This study analyzed three foreign laborers who had contracted enzyme-linked immunosorbent assay-confirmed A cantonensis infection while working in Taiwan. All three workers had consumed either roasted snails or raw snails flavored with seasoning while drinking wine. This study investigated possible risk factors for A cantonensis, including naturally occurring A cantonensis in A canaliculatus snails, viability of third-stage A cantonensis larvae in raw seasoned snails and in roasted snails, infectivity of larvae, and effects of alcohol while consuming snails. Positive infection rates in snails from five different irrigation canals in south Taiwan ranged from 12.3% to 29.4% and the average number of motile larvae per infected snail ranged from 36 to 65. The number of motile and coiled larvae in snail meat after 120 minutes seasoning was 93 (27.7% and 233 (69.3%, respectively. After 20 minutes of roasting, most larvae in the snail meat were dead. The infectivities of motile and coiled larvae from snail meat after 60 minutes seasoning were 53.2% and 33.2%, respectively, and those from snail meat after 5 minutes roasting were 33.2% and 7.0%, respectively. Eating Taiwan A canaliculatus snails raw is extremely risky given their high infection rates and infection intensities. Even after 120 minutes seasoning or after 20 minutes roasting, snail meat should be considered unsafe for human consumption. Finally, experimental rodent studies indicated that consuming alcohol while ingesting larvae does not significantly reduced infectivity.
-
Device for dewatering of raw biomass. Anordning foer avvattning och uppluckring av raa biomassa
Energy Technology Data Exchange (ETDEWEB)
Kubat, J; Aabom, J J.V.; Klason, T C.F.; Bultzingsloewen, F von
1993-09-27
This invention concerns a device for loosening of raw biomass through roll dewatering. It is primarily applicable for comminuted and milled raw wood. The invention is of special interest for the production of pulverized wood fuel
-
Fibromyalgia syndrome improved using a mostly raw vegetarian diet: An observational study
Directory of Open Access Journals (Sweden)
Speight Neal
2001-09-01
Full Text Available Abstract Background Fibromyalgia engulfs patients in a downward, reinforcing cycle of unrestorative sleep, chronic pain, fatigue, inactivity, and depression. In this study we tested whether a mostly raw vegetarian diet would significantly improve fibromyalgia symptoms. Methods Thirty people participated in a dietary intervention using a mostly raw, pure vegetarian diet. The diet consisted of raw fruits, salads, carrot juice, tubers, grain products, nuts, seeds, and a dehydrated barley grass juice product. Outcomes measured were dietary intake, the fibromyalgia impact questionnaire (FIQ, SF-36 health survey, a quality of life survey (QOLS, and physical performance measurements. Results Twenty-six subjects returned dietary surveys at 2 months; 20 subjects returned surveys at the beginning, end, and at either 2 or 4 months of intervention; 3 subjects were lost to follow-up. The mean FIQ score (n = 20 was reduced 46% from 51 to 28. Seven of the 8 SF-36 subscales, bodily pain being the exception, showed significant improvement (n = 20, all P for trend Conclusion This dietary intervention shows that many fibromyalgia subjects can be helped by a mostly raw vegetarian diet.
-
Energy Technology Data Exchange (ETDEWEB)
NONE
2010-11-15
In the contribution under consideration, the Federal Statistical Office (Wiesbaden, Federal Republic of Germany) and the Federal Environmental Agency (Dessau-Rosslau, Federal Republic of Germany) present actual data and analyses from environmentally economic total computations. In Germany, the use of raw materials became more efficient. Thus, 580 tons of raw materials per million Euro of gross domestic product were needed in the year 2008, while still 680 tons of raw materials were needed in the year 2000. The economical handling of natural resources relieves the environment and enables economic chances for individual companies and national economy. The lowering of environmental effects is to be in the focus of withdrawal and use of raw materials. This requires a stronger reduction of the consumption of raw materials. Savings potentials and an increased efficiency must be aspired in the short and medium term. The politics must create suitable incentives and framework conditions. The contribution under consideration presents new activities and strategies in order to achieve these targets.
-
Four-year monitoring of foodborne pathogens in raw milk sold by vending machines in Italy.
Giacometti, Federica; Bonilauri, Paolo; Serraino, Andrea; Peli, Angelo; Amatiste, Simonetta; Arrigoni, Norma; Bianchi, Manila; Bilei, Stefano; Cascone, Giuseppe; Comin, Damiano; Daminelli, Paolo; Decastelli, Lucia; Fustini, Mattia; Mion, Renzo; Petruzzelli, Annalisa; Rosmini, Roberto; Rugna, Gianluca; Tamba, Marco; Tonucci, Franco; Bolzoni, Giuseppe
2013-11-01
Prevalence data were collected from official microbiological records monitoring four selected foodborne pathogens (Salmonella, Listeria monocytogenes, Escherichia coli O157:H7, and Campylobacter jejuni) in raw milk sold by self-service vending machines in seven Italian regions (60,907 samples from 1,239 vending machines) from 2008 to 2011. Data from samples analyzed by both culture-based and real-time PCR methods were collected in one region. One hundred raw milk consumers in four regions were interviewed while purchasing raw milk from vending machines. One hundred seventy-eight of 60,907 samples were positive for one of the four foodborne pathogens investigated: 18 samples were positive for Salmonella, 83 for L. monocytogenes, 24 for E. coli O157:H7, and 53 for C. jejuni in the seven regions investigated. No significant differences in prevalence were found among regions, but a significant increase in C. jejuni prevalence was observed over the years of the study. A comparison of the two analysis methods revealed that real-time PCR was 2.71 to 9.40 times more sensitive than the culture-based method. Data on consumer habits revealed that some behaviors may enhance the risk of infection linked to raw milk consumption: 37% of consumers did not boil milk before consumption, 93% never used an insulated bag to transport raw milk home, and raw milk was consumed by children younger than 5 years of age. These results emphasize that end-product controls alone are not sufficient to guarantee an adequate level of consumer protection. The beta distribution of positive samples in this study and the data on raw milk consumer habits will be useful for the development of a national quantitative risk assessment of Salmonella, L. monocytogenes, E. coli O157, and C. jejuni infection associated with raw milk consumption.
-
Comparison of RAW264.7, human whole blood and PBMC assays to screen for immunomodulators.
Elisia, Ingrid; Pae, Han Bee; Lam, Vivian; Cederberg, Rachel; Hofs, Elyse; Krystal, Gerald
2018-01-01
The RAW264.7 mouse macrophage cell line is used extensively to carry out in vitro screens for immunomodulators. Compounds that are effective at reducing the expression of pro-inflammatory cytokines or nitric oxide (NO) from lipopolysaccharide (LPS)-stimulated RAW264.7 cells are often considered candidate anti-inflammatory agents for humans. There is, however, very little data on the reliability of this screen to identify bona fide human immunomodulators. We compared the efficacy of 37 purported immunomodulators to modulate LPS or E. coli-induced inflammatory responses in RAW264.7 cell, whole human blood and human peripheral blood mononuclear cell (PBMC) assays. Interestingly, there was no significant correlation (R=0.315) between the responses obtained with RAW264.7 cells and the whole blood assay (WBA), suggesting that compounds demonstrating efficacy in RAW264.7 cells may be ineffective in humans, and, more importantly, compounds that are effective in humans may be missed with a RAW264.7 screen. Interestingly, there was also no significant correlation between the WBA and human PBMCs when the latter were cultured with 10% FCS, but a moderate correlation was seen when the PBMCs were cultured with 25% autologous plasma. The presence of plasma thus contributes to the overall inflammatory response observed in the WBA. We then asked if RAW264.7 cells, given that they are mouse macrophage-like cells, respond in a manner similar to primary murine derived macrophages. Intriguingly, there was no significant correlation (R=0.012) with the 37 putative immunomodulators, pointing to distinct inflammatory response mechanisms in the two model systems. We conclude that the use of a WBA to confirm potential immunomodulators obtained from high throughput screening with RAW264.7 cells is advisable and that future screens be carried out using a WBA. Copyright © 2017 Elsevier B.V. All rights reserved.
-
Non-equilibrium thermionic electron emission for metals at high temperatures
Domenech-Garret, J. L.; Tierno, S. P.; Conde, L.
2015-08-01
Stationary thermionic electron emission currents from heated metals are compared against an analytical expression derived using a non-equilibrium quantum kappa energy distribution for the electrons. The latter depends on the temperature decreasing parameter κ ( T ) , which decreases with increasing temperature and can be estimated from raw experimental data and characterizes the departure of the electron energy spectrum from equilibrium Fermi-Dirac statistics. The calculations accurately predict the measured thermionic emission currents for both high and moderate temperature ranges. The Richardson-Dushman law governs electron emission for large values of kappa or equivalently, moderate metal temperatures. The high energy tail in the electron energy distribution function that develops at higher temperatures or lower kappa values increases the emission currents well over the predictions of the classical expression. This also permits the quantitative estimation of the departure of the metal electrons from the equilibrium Fermi-Dirac statistics.
-
Dubois, A E J; Pagliarani, G; Brouwer, R M; Kollen, B J; Dragsted, L O; Eriksen, F D; Callesen, O; Gilissen, L J W J; Krens, F A; Visser, R G F; Smulders, M J M; Vlieg-Boerstra, B J; Flokstra-de Blok, B J; van de Weg, W E
2015-11-01
Genetic modification of allergenic foods such as apple has the potential to reduce their clinical allergenicity, but this has never been studied by oral challenges in allergic individuals. We performed oral food challenges in 21 apple-allergic individuals with Elstar apples which had undergone gene silencing of the major allergen of apple, Mal d 1, by RNA interference. Downregulation of Mal d 1 gene expression in the apples was verified by qRT-PCR. Clinical responses to the genetically modified apples were compared to those seen with the wild-type Elstar using a visual analogue scale (VAS). Gene silencing produced two genetically modified apple lines expressing Mal d 1.02 and other Mal d 1 gene mRNA levels which were extensively downregulated, that is only 0.1-16.4% (e-DR1) and 0.2-9.9% (e-DR2) of those of the wild-type Elstar, respectively. Challenges with these downregulated apple lines produced significantly less intense maximal symptoms to the first dose (Vmax1) than with Elstar (Vmax1 Elstar 3.0 mm vs 0.0 mm for e-DR1, P = 0.017 and 0.0 mm for e-DR2, P = 0.043), as well as significantly less intense mean symptoms per dose (meanV/d) than with Elstar (meanV/d Elstar 2.2 mm vs 0.2 mm for e-DR1, P = 0.017 and 0.0 mm for e-DR2, P = 0.043). Only one subject (5%) remained symptom-free when challenged with the Elstar apple, whereas 43% did so with e-DR1 and 63% with e-DR2. These data show that mRNA silencing of Mal d 1 results in a marked reduction of Mal d 1 gene expression in the fruit and reduction of symptoms when these apples are ingested by allergic subjects. Approximately half of the subjects developed no symptoms whatsoever, and virtually all subjects wished to consume the apple again in the future. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.
-
Disinfection of wastewaters: high-energy electron vs gamma irradiation
Energy Technology Data Exchange (ETDEWEB)
Farooq, S [King Fahd Univ. of Petroleum and Minerals, Dhahran (Saudi Arabia). Dept. of Civil Engineering; Kurucz, C N; Waite, T D [Miami Univ., Coral Gables, FL (United States); Cooper, W J [Florida International Univ., Miami, FL (United States). Drinking Water Research Center
1993-07-01
A study was undertaken to examine the sensitivity of a wastewater population of coliphage, total coliforms and total flora present in raw sewage and secondary effluent after irradiating with similar doses delivered by a high-energy electron beam and [gamma]-radiation. The electron beam study was conducted on a large scale at the Virginia Key Wastewater Treatment Plant, Miami, Florida. The facility is equipped with a 1.5 MeV, 50 mA electron accelerator, with a wastewater flow rate of 8ls[sup -1]. Concurrent [gamma]-radiation studies were conducted at laboratory scale using a 5000 Ci, [sup 60]Co [gamma]-source. Three logs reduction of all three test organisms were observed at an electron beam dose of 500 krads, while at least four logs reduction were observed at the same dose utilizing the [gamma]'source. (Author).
-
Directory of Open Access Journals (Sweden)
S.P. Tsygankov
2013-07-01
Full Text Available Results of development and testing the tentative technology of sweet sorghum and finger millet processing into bioethanol are described. The carbohydrates content and range of the studied vegetable biomass as the raw material is defined. Bioethanol potential output from sugar sorghum and finger millet carbohydrates and key technological parameters of preparation of both types of vegetable raw material for alcohol fermentation are defined. The concept of the tentative technology of bioethanol production from carbohydrate raw material of the first and second generations is offered. Testing of complex transformation of carbohydrates from vegetable raw materials into bioethanol is performed.
-
RAWS II: A MULTIPLE REGRESSION ANALYSIS PROGRAM,
This memorandum gives instructions for the use and operation of a revised version of RAWS, a multiple regression analysis program. The program...of preprocessed data, the directed retention of variable, listing of the matrix of the normal equations and its inverse, and the bypassing of the regression analysis to provide the input variable statistics only. (Author)
-
Extraction of protoactinium from silicaceous raw material
Energy Technology Data Exchange (ETDEWEB)
Broda, E.
1946-07-01
This report was written by E. Broda and P.K. Wright at the Cavendish Laboratory (Cambridge) in March 1946 and is about the Extraction of protoactinium from a silicaceous raw material. In this report the isolation of Pa on Er carrier is described and it includes the experiment description and the discussion of the results. (nowak)
-
Lee, Hae Woo; Christie, Andrew; Liu, Jun Jay; Yoon, Seongkyu
2012-01-01
Understanding variability in raw materials and their impacts on product quality is of critical importance in the biopharmaceutical manufacturing processes. For this purpose, several spectroscopic techniques have been studied for raw material characterization, providing fast and nondestructive ways to measure quality of raw materials. However, investigations of correlation between spectra of raw materials and cell culture performance have been scarce due to their complexity and uncertainty. In this study, near-infrared spectra and bioassays of multiple soy hydrolysate lots manufactured by different vendors were analyzed using chemometrics approaches in order to address variability of raw materials as well as correlation between raw material properties and corresponding cell culture performance. Principal component analysis revealed that near-infrared spectra of different soy lots contain enough physicochemical information about soy hydrolysates to allow identification of lot-to-lot variability as well as vendor-to-vendor differences. The identified compositional variability was further analyzed in order to estimate cell growth and protein production of two mammalian cell lines under the condition of varying soy dosages using partial least square regression combined with optimal variable selection. The performance of the resulting models demonstrates the potential of near-infrared spectroscopy as a robust lot selection tool for raw materials while providing a biological link between chemical composition of raw materials and cell culture performance. Copyright © 2012 American Institute of Chemical Engineers (AIChE).
-
International Nuclear Information System (INIS)
Suresh Kumar, S.M.; Duraibabu, D.; Subramanian, K.
2014-01-01
Highlights: • UTCSE and TCSE composites have been fabricated by compression molding technique. • The prepared specimens were characterized by FTIR, DMA, TGA and SEM techniques. • TCSE composite showed higher mechanical properties compared to UTCSE composite. • DMA showed that TCSE composite exhibited higher storage modulus than UTCSE composite. • TCSE composite showed higher thermal stability than UTCSE composite. - Abstract: The untreated (raw) coconut sheath fiber reinforced epoxy (UTCSE) composite and treated coconut sheath fiber reinforced epoxy (TCSE) composite have been fabricated using hand layup followed by compression molding technique. The prepared specimens were characterized by Fourier transform infrared spectroscopy (FTIR), dynamic mechanical analysis (DMA), thermo gravimetric analysis (TGA) and scanning electron microscopy (SEM) techniques. The prepared specimens are cut as per ASTM Standards to measure tensile, flexural and impact strengths by using universal testing machine and izod impact tester respectively. The treated coconut sheath fiber reinforced epoxy composite (TCSE) posses higher mechanical strength and thermal stability compared to untreated (raw) coconut sheath fiber reinforced epoxy composite (UTCSE). In the SEM fracture analysis, TCSE composite showed better fiber–matrix bonding and absence of voids compared to UTCSE composite
-
Directory of Open Access Journals (Sweden)
Liliana Tudoreanu
2013-11-01
Full Text Available The present research was conducted to provide information on the influence of stunning methods in conjunction with refrigeration and freezing time on the textural and rheological properties of raw meat. Pork raw meat, commercially available, was analyzed for textural properties such as hardness, cohesiveness, adhesiveness and fracture force. Sample were analyzed fresh, after 3 days of refrigeration, and 15 days, 30days and 60 days freezing time in commercially available refrigerators mimicking the storing conditions used by consumers. For pork raw meat, hardness increased sharply after 3 days of refrigeration and showed no significant differences after 15days of freezing compared to 3days refrigeration time. After 30 days of freezing the raw pork meat samples’ hardness decreased significantly compared to the hardness of the samples freeze for15 days. Hardness of gas stunning raw pork meat samples compared to electrical stunning raw pork meat samples was 2.57 times higher indicating a better firmness of the gas stunning raw pork meat. The cohesiveness of the raw pork meat from gas stunned animals maintained its levels after 60 days of freezing while the meat from electrically stunned animals showed significant modificatio
-
DEFF Research Database (Denmark)
Christensen, Iben Vernegren; Ottosen, Lisbeth M.; Melcher, Eckhard
2005-01-01
. After soaking, a small amount of Cu and Cr was still present in the cell walls but larger particles were now found on wall surfaces. Most effective removal of Cu was obtained after soaking in phosphoric and oxalic acid followed by EDR; here numerous rice grain-shaped particles were observed containing...... large amounts of Cu and no Cr. Cr was most effectively removed after soaking in oxalic acid and subsequent EDR treatment or dual soaking in phosphoric acid and oxalic acid with and without subsequent EDR.......Soaking in different acids and electrodialytic remediation (EDR) were applied for removing copper and chromium from freshly Chromated Copper Arsenate (CCA) impregnated EN 113 pine wood samples. After remedial treatments, AAS analyses revealed that the concentration of copper (Cu) and chromium (Cr...
-
The early identification of anxiety-laden material with the aid of skin conductance measurements.
Lukens, H R
1979-01-01
Measured electrodermal responses (EDR), in the form of changes in skin conductivity, during administration of a calibration questionnaire (CQ) and a personal history questionnaire (PHQ) to each of 25 Ss. "Strong" changes were defined statistically for each S from the amplitudes of EDR evoked by the CQ. The free-floating anxiety of each S also was measured. As predicted on the grounds that questions of the PHQ were more likely than the non-personal questions of the CQ to intersect unresolved, anxiety-laden material, it was found that strong EDR evoked by the PHQ were significantly more likely to perseverate than those evoked by the CQ. Hence, the technique has potential clinical use in identifying anxiety-laden material. Free-floating anxiety did not correlate significantly with EDR data.
-
Effect of raw soya bean particle size on productive performance and digestion of dairy cows.
Naves, A B; Freitas Júnior, J E; Barletta, R V; Gandra, J R; Calomeni, G D; Gardinal, R; Takiya, C S; Vendramini, T H A; Mingoti, R D; Rennó, F P
2016-08-01
Differing soya bean particle sizes may affect productive performance and ruminal fermentation due to the level of fatty acid (FA) exposure of the cotyledon in soya bean grain and because the protein in small particles is more rapidly degraded than the protein in large particles, which influence ruminal fibre digestion and the amounts of ruminally undegradable nutrients. The objective of this experiment was to investigate the effects of raw soya bean particle size on productive performance, digestion and milk FA profile of dairy cows. Twelve Holstein cows were assigned to three 4 × 4 Latin squares with 21-day periods. At the start of the experiment, cows were 121 days in milk (DIM) and yielded 30.2 kg/day of milk. Cows were fed 4 diets: (i) control diet (CO), without raw soya bean; (ii) whole raw soya bean (WRS); (iii) cracked raw soya bean in Wiley mill 4-mm screen (CS4); and (iv) cracked raw soya bean in Wiley mill 2-mm screen (CS2). The inclusion of soya beans (whole or cracked) was 200 g/kg on dry matter (DM) basis and partially replaced ground corn and soya bean meal. Uncorrected milk yield and composition were not influenced by experimental diets; however, fat-corrected milk (FCM) decreased when cows were fed soya bean treatments. Soya bean diets increased the intake of ether extract (EE) and net energy of lactation (NEL ), and decreased the intake of DM and non-fibre carbohydrate (NFC). Ruminal propionate concentration was lower in cows fed WRS than cows fed CS2 or CS4. Cows fed cracked raw soya bean presented lower nitrogen in faeces than cows fed WRS. The milk of cows fed WRS, CS2 and CS4 presented higher unsaturated FA than cows fed CO. The addition of raw soya bean in cow diets, regardless of the particle size, did not impair uncorrected milk yield and nutrient digestion, and increased the concentration of unsaturated FA in milk. Cows fed cracked raw soya bean presented similar productive performance to cows fed whole raw soya bean. Journal of
-
Fabrication of WCp/NiBSi metal matrix composite by electron beam melting
Energy Technology Data Exchange (ETDEWEB)
Peng, Hui, E-mail: penghui@buaa.edu.cn [School of Materials Science and Engineering, Beihang University (BUAA), No. 37 Xueyuan Road, Beijing 100191 (China); Beijing Key Laboratory for Advanced Functional Material and Thin Film Technology, Beihang University, No. 37 Xueyuan Road, Beijing 100191 (China); Key Laboratory of Aerospace Materials & Performance (Ministry of Education), Beihang University, No. 37 Xueyuan Road, Beijing 100191 (China); Liu, Chang [School of Materials Science and Engineering, Beihang University (BUAA), No. 37 Xueyuan Road, Beijing 100191 (China); Guo, Hongbo, E-mail: guo.hongbo@buaa.edu.cn [School of Materials Science and Engineering, Beihang University (BUAA), No. 37 Xueyuan Road, Beijing 100191 (China); Beijing Key Laboratory for Advanced Functional Material and Thin Film Technology, Beihang University, No. 37 Xueyuan Road, Beijing 100191 (China); Key Laboratory of Aerospace Materials & Performance (Ministry of Education), Beihang University, No. 37 Xueyuan Road, Beijing 100191 (China); Yuan, Yuan [Zhuzhou Seed Cemented Carbide Technology Co. Ltd, No. 1099 Xiangda Road, Zhuzhou, Hunan 412000 (China); Gong, Shengkai; Xu, Huibin [School of Materials Science and Engineering, Beihang University (BUAA), No. 37 Xueyuan Road, Beijing 100191 (China); Beijing Key Laboratory for Advanced Functional Material and Thin Film Technology, Beihang University, No. 37 Xueyuan Road, Beijing 100191 (China); Key Laboratory of Aerospace Materials & Performance (Ministry of Education), Beihang University, No. 37 Xueyuan Road, Beijing 100191 (China)
2016-06-01
A blend of NiBSi and WC powders was used as raw material for fabricating a metal matrix composite (MMC) by electron beam melting (EBM). Dense and crack-free microstructure was produced with evenly distributed WC reinforcements. Mechanical properties, including macro- and micro-hardness, flexural strength, impact toughness and compressive strength, were investigated.
-
Fabrication of WCp/NiBSi metal matrix composite by electron beam melting
International Nuclear Information System (INIS)
Peng, Hui; Liu, Chang; Guo, Hongbo; Yuan, Yuan; Gong, Shengkai; Xu, Huibin
2016-01-01
A blend of NiBSi and WC powders was used as raw material for fabricating a metal matrix composite (MMC) by electron beam melting (EBM). Dense and crack-free microstructure was produced with evenly distributed WC reinforcements. Mechanical properties, including macro- and micro-hardness, flexural strength, impact toughness and compressive strength, were investigated.
-
IceBridge GPS L0 Raw Satellite Navigation Data
National Aeronautics and Space Administration — The NASA IceBridge GPS L0 Raw Satellite Navigation Data (IPUTG0) data set contains GPS readings, including latitude, longitude, track, ground speed, off distance,...
-
European initiative on cdio in raw material programmes
Edelbro, Catrin; Hulthén, Erik; Clausen, Elisabeth; Tanner, David; Herrera Herbert, Juan; Jonsson, Kristina; Bealieu, Stephan; Kamp, A.; Försth, Michael
2017-01-01
One of five Knowledge and Innovation Communities (KICs), was launched in Europe in 2014 and has its focus on exploration, extraction, mineral processing, metallurgy, recycling and material substitution of raw materials. To reach the vision, where the European Union’s industrial strength is based on
-
Arsenic species in raw and cooked rice: Implications for human health in rural Bengal
Energy Technology Data Exchange (ETDEWEB)
Halder, Dipti, E-mail: dipti@kth.se [KTH-International Groundwater Arsenic Research Group, Division of Land and Water Resources Engineering, Department of Sustainable Development, Environmental Sciences and Engineering, KTH Royal Institute of Technology, Teknikringen 76, SE-100 44 Stockholm (Sweden); Department of Chemistry, University of Kalyani, Kalyani, 741 235, West Bengal (India); Biswas, Ashis [KTH-International Groundwater Arsenic Research Group, Division of Land and Water Resources Engineering, Department of Sustainable Development, Environmental Sciences and Engineering, KTH Royal Institute of Technology, Teknikringen 76, SE-100 44 Stockholm (Sweden); Department of Chemistry, University of Kalyani, Kalyani, 741 235, West Bengal (India); Šlejkovec, Zdenka [Environmental Sciences Department, Jožef Stefan Institute, Jamova 39, 1000, Ljubljana (Slovenia); Chatterjee, Debashis [Department of Chemistry, University of Kalyani, Kalyani, 741 235, West Bengal (India); Nriagu, Jerome [Department of Environmental Health Sciences, School of Public Health, University of Michigan, 109 Observatory Street, Ann Arbor, MI 48109-2029 (United States); Jacks, Gunnar; Bhattacharya, Prosun [KTH-International Groundwater Arsenic Research Group, Division of Land and Water Resources Engineering, Department of Sustainable Development, Environmental Sciences and Engineering, KTH Royal Institute of Technology, Teknikringen 76, SE-100 44 Stockholm (Sweden)
2014-11-01
This study compares the concentrations of total and different species of arsenic (As) in 29 pairs of raw and cooked rice samples collected from households in an area of West Bengal affected by endemic arsenicism. The aim is to investigate the effects of indigenous cooking practice of the rural villagers on As accumulation and speciation in cooked rice. It is found that inorganic As is the predominant species in both raw (93.8%) and cooked rice (88.1%). Cooking of rice with water low in As (< 10 μg L{sup −1}) significantly decreases the total and inorganic As content in cooked rice compared to raw rice. Arsenic concentration is mainly decreased during boiling of rice grains with excess water. Washing of rice grains with low As water has negligible effect on grain As concentration. The study suggests that rice cooking with low As water by the villagers is a beneficial risk reduction strategy. Despite reductions in As content in cooked rice because of cooking with low As water, the consumption of cooked rice represents a significant health threat (in terms of chronic As toxicity) to the study population. - Highlights: • Pairs of raw and cooked rice samples are collected from households. • Total and different species of As in raw and cooked rice samples are compared. • Cooking with As safe water reduces total and inorganic As contents in cooked rice. • Inorganic As is the predominant species in both raw (93.8%) and cooked rice (88.1%). • Risks of As exposure from cooked rice consumption exceed the safety standards.
-
Studies on the key aroma compounds in raw (unheated) and heated Japanese soy sauce.
Kaneko, Shu; Kumazawa, Kenji; Nishimura, Osamu
2013-04-10
An investigation using the aroma extract dilution analysis (AEDA) technique of the aroma concentrate from a raw Japanese soy sauce and the heated soy sauce revealed 40 key aroma compounds including 7 newly identified compounds. Among them, 5(or 2)-ethyl-4-hydroxy-2(or 5)-methyl-3(2H)-furanone and 3-hydroxy-4,5-dimethyl-2(5H)-furanone exhibited the highest flavor dilution (FD) factor of 2048, followed by 3-(methylthio)propanal, 4-ethyl-2-methoxyphenol, and 4-hydroxy-2,5-dimethyl-3(2H)-furanone having FD factors from 128 to 512 in the raw soy sauce. Furthermore, comparative AEDAs, a quantitative analysis, and a sensory analysis demonstrated that whereas most of the key aroma compounds in the raw soy sauce were common in the heated soy sauce, some of the Strecker aldehydes and 4-vinylphenols contributed less to the raw soy sauce aroma. The model decarboxylation reactions of the phenolic acids during heating of the raw soy sauce revealed that although all reactions resulted in low yields, the hydroxycinnamic acid derivatives were much more reactive than the hydroxybenzoic acid derivatives due to the stable reaction intermediates. Besides the quantitative analyses of the soy sauces, the estimation of the reaction yields of the phenolic compounds in the heated soy sauce revealed that although only the 4-vinylphenols increased during heating of the raw soy sauce, they might not mainly be formed as decarboxylation products from the corresponding hydroxycinnamic acids but from the other proposed precursors, such as lignin, shakuchirin, and esters with arabinoxylan.
-
Arsenic species in raw and cooked rice: Implications for human health in rural Bengal
International Nuclear Information System (INIS)
Halder, Dipti; Biswas, Ashis; Šlejkovec, Zdenka; Chatterjee, Debashis; Nriagu, Jerome; Jacks, Gunnar; Bhattacharya, Prosun
2014-01-01
This study compares the concentrations of total and different species of arsenic (As) in 29 pairs of raw and cooked rice samples collected from households in an area of West Bengal affected by endemic arsenicism. The aim is to investigate the effects of indigenous cooking practice of the rural villagers on As accumulation and speciation in cooked rice. It is found that inorganic As is the predominant species in both raw (93.8%) and cooked rice (88.1%). Cooking of rice with water low in As (< 10 μg L −1 ) significantly decreases the total and inorganic As content in cooked rice compared to raw rice. Arsenic concentration is mainly decreased during boiling of rice grains with excess water. Washing of rice grains with low As water has negligible effect on grain As concentration. The study suggests that rice cooking with low As water by the villagers is a beneficial risk reduction strategy. Despite reductions in As content in cooked rice because of cooking with low As water, the consumption of cooked rice represents a significant health threat (in terms of chronic As toxicity) to the study population. - Highlights: • Pairs of raw and cooked rice samples are collected from households. • Total and different species of As in raw and cooked rice samples are compared. • Cooking with As safe water reduces total and inorganic As contents in cooked rice. • Inorganic As is the predominant species in both raw (93.8%) and cooked rice (88.1%). • Risks of As exposure from cooked rice consumption exceed the safety standards
-
2010-04-30
... review of the antidumping duty order on raw flexible magnets (``magnets'') from the People's Republic of... September 17, 2008. See Antidumping Duty Order: Raw Flexible Magnets from the People's Republic of China, 73..., International Trade Compliance Analyst, AD/CVD Operations, Office 4, ``Antidumping Duty Order on Raw Flexible...
-
Replacement of reserves zinc based on the recycling of technogenic raw materials
Directory of Open Access Journals (Sweden)
Olga Sergeevna Bryantseva
2013-06-01
Full Text Available In the article, the perspective trends of the expansion of the mineral-ore base of the Russian producers of zinc by recycling of technogenic raw materials are considered. The important role of recycling of resources for sustainable development of society and improve the environmental safety is justified. The main structural and dynamic characteristics of the use of mineral resource base for the production of zinc in Russia are considered. Raw materials opportunities and constraints for the development of zinc production are analyzed. In the paper, the structure and dynamics of the use of recycled materials by the largest producer of zinc in Russia are investigated. The methodical approach to the estimation of effectiveness of the industrial processing of technogenic metallurgical raw materials with the strategic flexibility of the implementation of projects is proposed and approved. The estimation of the effectiveness of a complex industrial processing of metallurgical zinc-containing dusts in a real production is carried out. The value of the strategic flexibility of the project of the industrial processing of the zinc-containing technogenic raw material is determined on the basis of the developed systematic approach. The value of the processes of recycling for sustainable production of zinc in Russia is revealed.
-
Stochastic Modelling and Self Tuning Control of a Continuous Cement Raw Material Mixing System
Directory of Open Access Journals (Sweden)
Hannu T. Toivonen
1980-01-01
Full Text Available The control of a continuously operating system for cement raw material mixing is studied. The purpose of the mixing system is to maintain a constant composition of the cement raw meal for the kiln despite variations of the raw material compositions. Experimental knowledge of the process dynamics and the characteristics of the various disturbances is used for deriving a stochastic model of the system. The optimal control strategy is then obtained as a minimum variance strategy. The control problem is finally solved using a self-tuning minimum variance regulator, and results from a successful implementation of the regulator are given.
-
Red mud addition in the raw meal for the production of Portland cement clinker.
Tsakiridis, P E; Agatzini-Leonardou, S; Oustadakis, P
2004-12-10
The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste, which is obtained from bauxite during the Bayer process for alumina production, in the raw meal for the production of Portland cement clinker. For that reason, two samples of raw meals were prepared: one with ordinary raw materials, as a reference sample ((PC)Ref), and another with 3.5% red mud ((PC)R/M). The effect on the reactivity of the raw mix was evaluated on the basis of the unreacted lime content in samples sintered at 1350, 1400 and 1450 degrees C. Subsequently, the clinkers were produced by sintering the two raw meals at 1450 degrees C. The results of chemical and mineralogical analyses as well as the microscopic examination showed that the use of the red mud did not affect the mineralogical characteristics of the so produced Portland cement clinker. Furthermore, both clinkers were tested by determining the grindability, setting time, compressive strength and expansibility. The hydration products were examined by XRD analysis at 2, 7, 28 and 90 days. The results of the physico-mechanical tests showed that the addition of the red mud did not negatively affect the quality of the produced cement.
-
McAuley, Catherine M; Britz, Margaret L; Gobius, Kari S; Craven, Heather M
2015-12-01
This study investigated the prevalence, seasonality, and species variety of enterococci present in raw milk factory silos and pasteurized milk in 3 dairying regions in Victoria, Australia, over a 1-yr period. Additionally, the growth ability of thermoduric enterococci isolated in this study (Enterococcus faecalis, E. faecium, E. hirae, and E. durans) was determined in milk at temperatures likely to occur during storage, transport, and distribution, and before domestic consumption (4 and 7°C). Enterococci were detected in 96% of 211 raw milk samples, with an average count of 2.48 log10 cfu/mL. Counts were significantly lower in winter than summer (average 1.84 log10 cfu/mL) and were different between factories but not regions. Enterococcus faecalis was the most prevalent species isolated from raw milk in every factory, comprising between 61.5 and 83.5% of enterococcal species across each season. Enterococci were detected in lower numbers in pasteurized milk than in raw milk and were below the limit of detection on spread plates (pasteurization. Residual viable cells were only detected following enrichment using 100-mL samples of milk, with 20.8% of the samples testing positive; this equated to a decrease in the average raw milk enterococci count of >4 log10 cfu/mL following pasteurization. Although E. faecalis predominated in raw milk and E. durans was found in only 2.9% of raw milk samples, E. durans was the most prevalent species detected in pasteurized milk. The detection of enterococci in the pasteurized milk did not correlate with higher enterococci counts in the raw milk. This suggested that the main enterococci populations in raw milk were heat-sensitive and that thermoduric enterococci survived pasteurization in a small numbers of instances. All of the thermoduric enterococci that were assessed for growth at likely refrigeration temperatures were able to grow at both 4 and 7°C in sterile milk, with generation times of 35 to 41h and 16 to 22h, respectively
-
75 FR 14479 - Reallocation of Unused Fiscal Year 2010 Tariff-Rate Quota Volume for Raw Cane Sugar
2010-03-25
...-Rate Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION... (TRQ) for imported raw cane sugar. DATES: Effective Date: March 25, 2010. ADDRESSES: Inquiries may be... (HTS), the United States maintains TRQs for imports of raw cane and refined sugar. Section 404(d)(3) of...
-
75 FR 26316 - Allocation of Additional Fiscal Year (FY) 2010 In-Quota Volume for Raw Cane Sugar
2010-05-11
...-Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar. DATES: Effective Date: May 11, 2010. ADDRESSES: Inquiries may be mailed... (HTS), the United States maintains TRQs for imports of raw cane and refined sugar. Section 404(d)(3) of...
-
Hennebel, T.; Boon, N.; Maes, S.; Lenz, M.
2015-01-01
Europe is confronted with an increasing supply risk of critical raw materials. These can be defined as materials of which the risks of supply shortage and their impacts on the economy are higher compared to most of other raw materials. Within the framework of the EU Innovation Partnership on raw
-
Database-driven primary analysis of raw sequencing data
DEFF Research Database (Denmark)
2014-01-01
The present invention relates to methods for identifying the source of a biological sequence containing sample from raw sequencing reads. The method may be used to identify the source of unknown DNA and can be used for diagnostic, biodefense, food safety and quality, and hygiene applications...
-
Martin, N H; Ranieri, M L; Murphy, S C; Ralyea, R D; Wiedmann, M; Boor, K J
2011-03-01
Analytical tools that accurately predict the performance of raw milk following its manufacture into commercial food products are of economic interest to the dairy industry. To evaluate the ability of currently applied raw milk microbiological tests to predict the quality of commercially pasteurized fluid milk products, samples of raw milk and 2% fat pasteurized milk were obtained from 4 New York State fluid milk processors for a 1-yr period. Raw milk samples were examined using a variety of tests commonly applied to raw milk, including somatic cell count, standard plate count, psychrotrophic bacteria count, ropy milk test, coliform count, preliminary incubation count, laboratory pasteurization count, and spore pasteurization count. Differential and selective media were used to identify groups of bacteria present in raw milk. Pasteurized milk samples were held at 6°C for 21 d and evaluated for standard plate count, coliform count, and sensory quality throughout shelf-life. Bacterial isolates from select raw and pasteurized milk tests were identified using 16S ribosomal DNA sequencing. Linear regression analysis of raw milk test results versus results reflecting pasteurized milk quality consistently showed low R(2) values (tests and results from tests used to evaluate pasteurized milk quality. Our findings suggest the need for new raw milk tests that measure the specific biological barriers that limit shelf-life and quality of fluid milk products. Copyright © 2011 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.
-
Gas condensate--raw material for producing liquid paraffin hydrocarbons
Energy Technology Data Exchange (ETDEWEB)
Aliyeva, R.B.; Alikishi-Zade, G.Yu.; Kuliyev, A.M.; Leonidov, A.N.; Pereverzev, A.N.
1980-01-01
The problem of efficient utilization of gas condensates as raw material for removal of a valuable product, liquid paraffins, is examined. A classification of gas condensates is given which is used as raw material for removing these hydrocarbons: gas condensate with high content of n-alkanes (25-40 mass percent), with average content (18-25 mass percent), with low content (12-18 mass percent), light weight fractions compositions, which do not contain fractions up to 200/sup 0/, and also, content ofless than 12% n-alkanes. Gas condensate I-III groups are 30% of the total reserve of gas condensate. Liquid paraffins hydrocarbons, produced from fractions of diesel fuel, which has been removed from Shatlyk gas condensate under conditions which simulate virtual processes of caramide deparaffinization meet all requirements without additional refining.
-
Agaves as a raw material: recent technologies and applications.
Narváez-Zapata, J A; Sánchez-Teyer, L F
2009-01-01
Agave plants are a valuable source of raw material due to its fibrous and complex sugar content of their leaves and core, and their bagasse waste can be use for several aims. This plant genus belongs to the Agavaceae family and until now more than 200 species have been described. A large number of Agave species are currently used as raw material in several biotechnological processes. This review shows the reported applications and patents on fields like alcoholic brewages with special reference to Tequila and Mezcal, the isolation and use of compounds such as saponins and agave fructans, and their potential biotechnological application on several human demands. The process to obtain fibers and cellulose, stock feeds, and several miscellaneous extractives are also reviewed. Some possibilities and problems of cultivation are discussed.
-
International Nuclear Information System (INIS)
Kanlayakrit, Werasit; Piadang, Nattayana; Maweang, Metinee
2006-09-01
Aspergillus awamori was induced to mutation by gamma ray to improve raw-starch digestibility of amylase enzyme. Twenty fungal colonies were selected base on and amylase and glucoamylase activities including raw starch digestibility. The result showed that isolate A a(i)-2(16) was the best isolate for raw-starch digestion (65.64 %). It produced extracellular amylase enzyme which showed highest raw-starch digestibility more than wild type about 2 folds. Based on enzymes from solid culture showed activities higher from liquid medium. Therefore solid culture is suitable for fungal enzyme production.
-
DEFF Research Database (Denmark)
Fonteyne, Margot; Wickström, Henrika; Peeters, Elisabeth
2014-01-01
over a range of raw material attributes, manufacturing process options and process parameters. This fits further into the Process Analytical Technology (PAT) and Quality by Design (QbD) framework. The present study evaluates the effect of variation in critical raw material properties on the critical......-Lactose-PVP (30-67.5-2.5%) was used as model formulation. Seven different grades of theophylline were granulated. Afterward, the obtained granules were tableted. Both the characteristics of granules and tablets were determined. The results show that differences in raw material properties both affect...... quality attributes of granules and tablets, produced by a continuous from-powder-to-tablet wet granulation line. The granulation process parameters were kept constant to examine the differences in the end product quality caused by the variability of the raw materials properties only. Theophylline...
-
Experiences with mobile units for liquid raw management in slovak and czech nuclear power plants
International Nuclear Information System (INIS)
Rapant, T.; Tatransky, P.; Vasko, M.; Hlavacka, R.
2015-01-01
Text describes the experience from multiple projects of retrieval, pre-treatment and final treatment of liquid radioactive waste in Slovak and Czech NPPs during last 20 years. The purpose of these projects was to retrieve RAW (sludge, used resins, crystalline sediments, other types of liquid RAW) from operational tanks or technological systems, its pre-treatment and its solidification into 200 l or 60 l drums. Slovak and Czech NPPs are WWER 440 type (except Bohunice A1 NPP) where operational liquid RAW should be stored in large capacity tanks during the whole operational period. Volume of tanks placed in auxiliary buildings is from 460 to 550 m 3 , usually they are situated in rooms with limited access and minimal handling space. The liquid RAW management process is described. (authors)
-
To the question of peculiarities of thermal activation of natural siliceous raw material
Directory of Open Access Journals (Sweden)
Chumachenko Natalya
2017-01-01
Full Text Available The results of research of activity enhancement of natural siliceous raw material are given in the article. Fossil meal of Khotynetsky deposit, diatomite of Sharlovsky deposit, silica clay of Balasheika deposit were used as natural active mineral admixtures. The influence of heat-treating temperature and dispersion on activity of different types of siliceous raw material is studied. The increase of activity of fixation of Ca(OH2 in several times is traced after heat-treating at a certain temperature in the range from 100 to 800°C. The type of activity change is discovered. Explanation is given connected with the change of silica structure in the surface layer. Parameters of the highest activity are defined for every type of siliceous raw material.
-
Directory of Open Access Journals (Sweden)
Mitsugi Shimoda
2012-06-01
Full Text Available Background: The effects of Edaravone (Edr on hepatic ischemia-reperfusion (I/R injury and liver regeneration were examined in a pig hepatectomy model. Methods: One hour of ischemia was induced by occluding the vessels and the bile duct of the right and median lobes. About a 40% left hepatectomy was performed after reperfusion. Six animals received Edr (3 mg/kg/h intravenously and six control animals received saline just before reperfusion. Remnant liver volume, hemodynamics, and levels of AST, ALT, LDH, and LA were compared between the groups. Expression of TGF-beta1 and IL-6 mRNA in hepatic tissues was examined using RT-PCR. Apoptosis and cell proliferation were demonstrated by TUNEL and Ki-67 staining, respectively. Results: Serum AST, LDH, and LA levels were significantly lower at 3 hours and 1 week after perfusion in animals that had received Edr. In the Edr group, hepatic tissues showed a greater tendency for the expression of TGF-beta1 mRNA to be inhibited at 1 week, although the difference was not significant. Also at 1 week in the Edr group, TUNEL-positive cells in the hepatic sinusoidal endothelium were significantly fewer, and Ki-67-positive cells were significantly more numerous. Conclusion: We conclude that Edr reduces hepatic injury and supports tissue regeneration after I/R injury in this pig model. [Arch Clin Exp Surg 2012; 1(3.000: 142-150
-
Microbiologically influenced corrosion of sa106 gr.b carbon steel in raw water
International Nuclear Information System (INIS)
Tunaru, M.; Velciu, L.; Stancu, M.; Popa, L.
2015-01-01
This paper presents the evaluation of microbiological corrosion susceptibility of carbon steel SA106gr.B in raw water. The experiment consisted of a series of electrochemical accelerated tests which evaluated the pitting corrosion susceptibility and determined corrosion rates before and after the immersion. The microbiological analysis of the water determined the types of bacteria and bacterial concentration present in water and in biofilms. Microbiological analysis of the water sample emphasized the existence, in small numbers (10-101 ml-1), of heterotrophic aerobic bacteria, sulphate-reducing bacteria and iron-oxidizing microorganisms. Along with sulphate-reducing bacteria, the heterotrophic aerobic bacteria and the iron-oxidizing microorganisms are categorized as having an important role in the corrosion of metals, including steel. The surfaces of the tested samples were analysed using the optical and electronic microscope, and emphasized the role of bacteria in the development of biofilms under which appeared characteristics of corrosion attack. (authors)
-
Branding Raw Material to Improve Human Rights: Intel’s Ban on Conflict Minerals
Directory of Open Access Journals (Sweden)
Osburg Thomas
2016-05-01
Full Text Available Many companies seek to take over more responsibility for their supply chain and their raw materials. Intel was one of the first companies investigating the origin of conflict minerals like tin, tantalum, gold or tungsten, which are used in many electronic products. Their path to ultimately offering conflict-free microprocessors took more than five years of consistent preparation and intensive reengineering of the business process. They identified smelters as a bottleneck in the supply chain and started cooperating closely with them to trace their minerals’ supply. By developing a bag-and-tag system the company is now able to ensure that their minerals are not sourced from illegal mines, which often finance illegal warlords, for example, in the eastern Democratic Republic of Congo. The cooperation with the smelters brings about higher demand and in consequence higher prices for the legally sourced minerals. Many small miners and their families in the region directly benefit from the higher earnings.
-
Raw materials for reflector graphite (for reactors)
International Nuclear Information System (INIS)
Wilhelmi, G.; Mindermann, D.
1992-01-01
The manufacturing concept for the core components of German high temperature reactor (HTR) types of graphite was previously entirely directed to the use of German tar coke (St coke). As the plants for producing this material no longer complied technically with the current environmental protection requirements, one had to assume that they would soon be shut down. To prevent bottlenecks in the erection of future HTR plants, alternative cokes produced by modern processes by Japanese manufacturers were checked for their suitability for the manufacture of reactor graphite. This report describes the investigations carried out on these materials from the safe delayed coking process. The project work, apart from analysis of the main data of the candidate coke considered, included the processing of the raw materials into directly and secondarily extruded graphite rods on the laboratory scale, including characterisation. As the results show, the material data achieved with the previous raw material can be reproduced with Japanese St coke. The tar coke LPC-A from the Nippon Steel Chemical Co., Ltd was decided on as the new standard coke for manufacturing reflector graphite. (orig.) With 15 tabs., 2 figs [de
-
76 FR 42160 - Allocation of Additional Fiscal Year (FY) 2011 In-Quota Volume for Raw Cane Sugar
2011-07-18
...-Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar. USTR is also reallocating a portion of the unused original FY 2011 TRQ... imports of raw cane and refined sugar. Section 404(d)(3) of the Uruguay Round Agreements Act (19 U.S.C...
-
Vermeulen, M.; Klöpping-Ketelaars, I.W.A.A.; Berg, R. van den; Vaes, W.H.J.
2008-01-01
The aim of this study was to determine the bioavailability and kinetics of the supposed anticarcinogen sulforaphane, the hydrolysis product of glucoraphanin, from raw and cooked broccoli. Eight men consumed 200 g of crushed broccoli, raw or cooked, with a warm meal in a randomized, free-living, open
-
Visciano, Pierina; Perugini, Monia; Manera, Maurizio; Abete, Maria Cesarina; Tarasco, Renata; Salese, Carmine; Amorena, Michele
2013-12-18
The distribution of total arsenic in different portions of Norway lobster (Nephrops norvegicus L., Crustacea) was studied both in fresh samples and after a boiling process. All individuals (n = 80) were selected of medium standard commercial size (13-15 cm). The highest mean concentrations (26.86 ± 1.57 mg/kg wet weight (ww)) were found in the raw brown meat of the crustacean, probably due to its detoxification role, whereas the lowest mean values (15.97 ± 0.85 mg/kg ww) were in the raw exoskeleton. The raw white meat reported mean values of 16.09 ± 0.61 mg/kg ww. The levels of arsenic contamination detected in the boiled portions showed a significant (p < 0.01) decrease compared to the raw portions, as a consequence of solubilization phenomena. In fact, a large amount of arsenic from raw lobsters was transferred to the corresponding boiling broth. In the most commonly consumed portion, the white meat, only slight losses (7.22%) in total arsenic content were observed compared to the raw portion.
-
Influence of raw milk quality on fluid milk shelf life.
Barbano, D M; Ma, Y; Santos, M V
2006-03-01
Pasteurized fluid milk shelf life is influenced by raw milk quality. The microbial count and somatic cell count (SCC) determine the load of heat-resistant enzymes in milk. Generally, high levels of psychrotrophic bacteria in raw milk are required to contribute sufficient quantities of heat-stable proteases and lipases to cause breakdown of protein and fat after pasteurization. Sanitation, refrigeration, and the addition of CO2 to milk are used to control both total and psychrotrophic bacteria count. It is not uncommon for total bacterial counts of raw milk to be milk processors have not focused much attention on milk SCC. Increased SCC is correlated with increased amounts of heat-stable protease (plasmin) and lipase (lipoprotein lipase) in milk. When starting with raw milk that has a low bacterial count, and in the absence of microbial growth in pasteurized milk, enzymes associated with high SCC will cause protein and fat degradation during refrigerated storage, and produce off-flavors. As the ability to kill, remove, or control microbial growth in pasteurized refrigerated milk continues to improve, the original milk SCC will be the factor limiting the time of refrigerated storage before development of an off-flavor in milk. Most healthy cows in a dairy herd have a milk SCC 200,000 cell/mL are usually due to the contribution of high SCC milk from a small number of cows in the herd. Technology to identify these cows and keep their milk out of the bulk tank could substantially increase the value of the remaining milk for use in fluid milk processing. To achieve a 60- to 90-d shelf life of refrigerated fluid milk, fluid processors and dairy farmers need to work together to structure economic incentives that allow farmers to produce milk with the SCC needed for extended refrigerated shelf life.
-
Equipment for RAW handling, packaging, transport and storage from ZTS VVU KOSICE a.s
International Nuclear Information System (INIS)
Vargovcik, L.
2004-01-01
Since 1988, the company ZTS VVU KOSICE has devoted a great part of its activities to the development of equipment for RAW handling, packaging, transport and storage, mainly for application in the decommissioning of NPP A1 at Jaslovske Bohunice in Slovakia. This is a HWGCR NPP shut down following a breakdown in 1977. This incident was caused by disruption of the technological channel serving as a barrier between heavy water moderator and fuel assembly. Damage of this barrier enabled heavy water leakage into the primary circuit with partial fuel elements cladding damage and subsequent additional contamination of the primary circuit. During two consecutive years after the incident main effort was focused on activities related to personnel and environment protection, moderator draining, reactor defuelling, dry cleaning of the primary circuit, repair and maintenance of equipment. The next step was the preparation of the concept of NPP A-1 introduction into dry safe state. The order of importance of RAW liquidation was as follows: 1. Spent fuel - spent fuel assemblies from NPP A-1 were, after short cooling, stored temporarily in storage pipe containers filled at the beginning of NPP operation with ''chrompik'' (an aqueous solution of K 2 Cr 2 O 7 with concentration of 3-5%), later with ''dowtherm'' (mixture of bi-phenyl oxide and bi-phenyl). The containers were placed in a storage pond filled with water. 2. Liquid RAW - combustible (dowtherm, oils) and non-combustible (chrompik, Demi water, decontaminating solutions, sludge, sorbents, etc.) 3. Solid RAW - metallic and non-metallic For this purpose, it was necessary to build RAW processing lines, intermediate storage facilities and systems for manipulation and transport of RAW
-
Optimizing Pretreatment of Medicinal Raw Materials by RFC Plasma before Extraction
Directory of Open Access Journals (Sweden)
O.Yu. Kuznetsova
2016-06-01
Full Text Available Optimization of the RF-plasma treatment modes of chaga raw materials using the Statistica 6.0 software package has been performed. Mathematical design has been carried out to calculate the optimum parameters of RF-plasma treatment using three plasma-forming gases – argon, air, and nitrogen. Plasma treatment of chaga raw materials has been undertaken at the constant parameters: pressure P = 30.0 Pa, anodic current J = 0.7 A, gas consumption G = 0.04 g/s; the variable parameters were power U = 5.0÷7.0 kV and treatment duration at the high-frequency capacitor category of the lowered pressure t = 30÷60 min. Optimization of four key parameters for extraction of chaga raw materials (solid residue, melanin yield, antioxidant activity of both extract and chaga melanin depending on the chosen plasma-forming gas (argon, air, or nitrogen has been achieved. The optimum modes of RF-plasma treatment allowing to obtain the extracts and melanin of chaga mushroom with the improved physicochemical and antioxidant characteristics have been calculated.
-
New and non-traditional mineral raw materials deposits, perspectives of use
International Nuclear Information System (INIS)
Beyseev, O.; Beyseev, A.; Baichigasov, I.; Sergev, E.; Shakirova, G.
1996-01-01
Deposits of new and non-traditional kinds of mineral raw material are revealed, explored and prepared to industrial recovery in Kazakstan, that can be used in frames of conversion process to create new materials with unique properties, to prepare base for new technologies elaboration, and to achieve appreciable economic benefit. These deposits are located mostly in geographic and economic conditions of advanced infrastructure and mining works network, favorable for recovery.On the tests results the following is of heaviest interest: RHODUCITE, NEMALITE-CONTAINING CHRYSOTILE-ASBESTOS, NICKEL-CONTAINING SILICATE-ASBOLAN ORES, MEDICINAL MINERALS, SHUNGITES, FULLERENES, RAW QUARTZ MINERALS - the group of deposits containing 5 min tons of high quality quartz good for manufacture of cut-glass and fibre-optical articles, is explored in details. There are also deposits of other kinds of non-traditional strategic mineral raw material in the Republic of Kazakstan - natural fillers, that can be used in the national economy of the country and bring considerable economic benefit: chrysotile-asbestos, amphibole-asbestos, talk, vollastonite, tremolite, actinolite, vermiculite, zeolite, etc
-
Mueller, Sandra R; Wäger, Patrick A; Turner, David A; Shaw, Peter J; Williams, Ian D
2017-10-01
An increasing number of geochemically scarce metallic raw materials are entering into our lives via new technologies. A reversal of this trend is not foreseeable, leading to concerns regarding the security of their supply. However, the evaluation of raw material supply is currently hampered by inconsistent use of fundamental terminologies and incomplete assessment criteria. In this paper, we aim to establish a consistent framework for evaluating raw material supply from both anthropogenic and geological sources. A method for concept extraction was applied to evaluate systematically the use of fundamental terms in the evaluation of raw material supply. The results have shown that 'availability' is commonly used in raw material supply evaluations, whilst other researchers suggest that raw material supply should be evaluated based on 'accessibility'. It was revealed that 'accessibility' actually comprises two aspects: 'availability' and 'approachability'. Raw material 'approachability' has not previously been explicitly addressed at a system level. A novel, consistent framework for evaluating raw material supply was therefore developed. To demonstrate the application of the established framework, we evaluated the raw material supply of four rare earth element case studies. Three case studies are End-of-Life products (the anthroposphere) from Switzerland: (i) phosphors in fluorescent lamps, (i) permanent magnets in the drive motors of electric cars and (iii) fibre optic cable. The fourth case study source is the Earth's crust (the geosphere): Mount Weld deposit in Australia. The framework comprises a comprehensive evaluation of six components relating to raw material mining and processing: their geological knowledge, eligibility, technology, economic, societal and environmental impacts. Our results show that metals are not considered to be fully accessible in any of the case studies due to a lack of necessary technologies and potential societal and environmental
-
TATA LETAK GUDANG RAW MATERIAL CHEMICAL MENGGUNAKAN METODE SHARED STORAGE DAN REL SPACE
Directory of Open Access Journals (Sweden)
Indramawan Hadi Kuswoyo
2016-04-01
Full Text Available Storage system in the manufacturing industry in this modern era is a very important role especially international scale company, may not directly produce or distribute all of the work unit. this led to the need for raw materials warehouse, warehouse storage systems should not be large in size because if supported by a good inventory of the warehouse to the maximum utilization of the problems faced by the company occurred in the warehouse of raw materials (raw materials. deficiencies in the arrangement of items in the warehouse procedures cause problems in the warehouse, so the warehouse impressed narrow and less structured cause inefficiencies time retrieval and storage of materials, as well as complicate the operator in handling the placement process raw materials. In the method of shared storage and rail space (relationchip chart for the relationship between activity is indicated by activity relationship approach, which shows each activity as a single activity model in the form of a diagram. ARD basic idea of the link between patterns of flow of goods and location of service activities related to production activities. ARD is the development of ARC (activity relationship chart.
-
Identification of predominant aroma components of raw, dry roasted and oil roasted almonds.
Erten, Edibe S; Cadwallader, Keith R
2017-02-15
Volatile components of raw, dry roasted and oil roasted almonds were isolated by solvent extraction/solvent-assisted flavor evaporation and predominant aroma compounds identified by gas chromatography-olfactometry (GCO) and aroma extract dilutions analysis (AEDA). Selected odorants were quantitated by GC-mass spectrometry and odor-activity values (OAVs) determined. Results of AEDA indicated that 1-octen-3-one and acetic acid were important aroma compounds in raw almonds. Those predominant in dry roasted almonds were methional, 2- and 3-methylbutanal, 2-acetyl-1-pyrroline and 2,3-pentanedione; whereas, in oil roasted almonds 4-hydroxy-2,5-dimethyl-3(2H)-furanone, 2,3-pentanedione, methional and 2-acetyl-1-pyrroline were the predominant aroma compounds. Overall, oil roasted almonds contained a greater number and higher abundance of aroma compounds than either raw or dry roasted almonds. The results of this study demonstrate the importance of lipid-derived volatile compounds in raw almond aroma. Meanwhile, in dry and oil roasted almonds, the predominant aroma compounds were derived via the Maillard reaction, lipid degradation/oxidation and sugar degradation. Copyright © 2016 Elsevier Ltd. All rights reserved.
-
Plesiomonas shigelloides Periprosthetic Knee Infection After Consumption of Raw Oysters.
Hustedt, Joshua W; Ahmed, Sarim
Periprosthetic infections are a leading cause of morbidity after total joint arthroplasty. Common pathogens include Staphylococcus aureus, streptococcus, enterococcus, Escherichia coli, and Pseudomonas aeruginosa. However, there are many cases in which rare bacteria are isolated. This case report describes a periprosthetic knee infection caused by Plesiomonas shigelloides. In the United States, P shigelloides and 2 other Vibrionaceae family members, Vibrio vulnificus and Vibrio parahaemolyticus, are most often contracted from eating raw oysters and shellfish. P shigelloides usually causes a self-limiting watery diarrhea, but in immunosuppressed people it can cause septicemia. In this case report, a chemically and biologically immunosuppressed man consumed raw oysters and developed P shigelloides septicemia and acute periprosthetic knee infection that required surgical intervention.
-
Electrodialytic Remediation of Soil Fines (<63μm) in Suspension
DEFF Research Database (Denmark)
Jensen, Pernille Erland; Ottosen, Lisbeth M.; Ferreira, Célia
2007-01-01
Current treatment of the remaining soil fines from soil wash is onerous and expensive, and therefore, in this work, we investigated the feasibility of electrodialytic remediation (EDR) as an alternative treatment. The study focuses on EDR efficiency as a function of current strength, liquid......-exchange membrane increased the pH, and this resulted in decreased remediation efficiency. It was shown that complete remediation of the soil-fines is possible, with the majority of the Pb being transported into the catholyte and precipitated at the cathode. Based on the results it is recommended that EDR...
-
International Nuclear Information System (INIS)
Meigs, R.A.
1985-12-01
The purpose of this report is to document the initial decontamination of the Equipment Decontamination Room (EDR). The effort spanned a two-year period and included packaging and removal of waste; grinding away contaminated concrete floors; pump-out and spraydown of an equipment soaking pit; washing and painting of walls, equipment, and floors; refurbishment of utilities and various pieces of equipment; and load tests of EDR and Chemical Process Cell (CPC) cranes. After decontamination, the EDR was converted into a waste handling area for the decommissioning of the CPC
-
Energy Technology Data Exchange (ETDEWEB)
Fonseca, Heverton C.O.; Garcia, Rafael H.L.; Ferreira, Robson J.; Silva, Flavia R.O.; Potiens Junior, Ademar J.; Sakata, Solange K., E-mail: sksakata@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)
2015-07-01
{sup 90}Sr, a radioactive isotope of strontium, is one of the fission products and quite often present in the radioactive waste produced by nuclear power plants. Recently, the removal efficiency of strontium by treated coconut fibers was evaluated and reached up to 95% in an aqueous solution. This work presents the characterization of raw and treated coconut fibers with different concentrations of hydrogen peroxide in basic medium using X-ray diffraction (XRD) and scanning electron microscopy/energy dispersive spectroscopy (SEM / EDS). The analysis of X-ray diffraction shows a crystallinity of 37.6% for raw coconut fiber and crystallinity of 45.4% and 50.6% for coconut fibers 1 and 2, respectively. These results showed that the different degrees of degradation of organic matter can affect the crystallinity of the treated. This study of morphology and crystallinity of theses biosorbent materials with strontium will help in comprehension of the effects of alkaline hydrogen peroxide treatment and it will demonstrate the potential of strontium uptake by coconut fibers. (author)
-
International Nuclear Information System (INIS)
Fonseca, Heverton C.O.; Garcia, Rafael H.L.; Ferreira, Robson J.; Silva, Flavia R.O.; Potiens Junior, Ademar J.; Sakata, Solange K.
2015-01-01
90 Sr, a radioactive isotope of strontium, is one of the fission products and quite often present in the radioactive waste produced by nuclear power plants. Recently, the removal efficiency of strontium by treated coconut fibers was evaluated and reached up to 95% in an aqueous solution. This work presents the characterization of raw and treated coconut fibers with different concentrations of hydrogen peroxide in basic medium using X-ray diffraction (XRD) and scanning electron microscopy/energy dispersive spectroscopy (SEM / EDS). The analysis of X-ray diffraction shows a crystallinity of 37.6% for raw coconut fiber and crystallinity of 45.4% and 50.6% for coconut fibers 1 and 2, respectively. These results showed that the different degrees of degradation of organic matter can affect the crystallinity of the treated. This study of morphology and crystallinity of theses biosorbent materials with strontium will help in comprehension of the effects of alkaline hydrogen peroxide treatment and it will demonstrate the potential of strontium uptake by coconut fibers. (author)
-
Soft electron processor for surface sterilization of food material
International Nuclear Information System (INIS)
Baba, Takashi; Kaneko, Hiromi; Taniguchi, Shuichi
2004-01-01
As frozen or chilled foods have become popular nowadays, it has become very important to provide raw materials with lower level microbial contamination to food processing companies. Consequently, the sterilization of food material is one of the major topics for food processing. Dried materials like grains, beans and spices, etc., are not typically deeply contaminated by microorganisms, which reside on the surfaces of materials, so it is very useful to take low energetic, lower than 300 keV, electrons with small penetration power (Soft-Electrons), as a sterilization method for such materials. Soft-Electrons is researched and named by Dr. Hayashi et al. This is a non-thermal method, so one can keep foods hygienic without serious deterioration. It is also a physical method, so is free from residues of chemicals in foods. Recently, Nissin-High Voltage Co., Ltd. have developed and manufactured equipment for commercial use of Soft-Electrons (Soft Electron Processor), which can process 500 kg/h of grains. This report introduces the Soft Electron Processor and shows the results of sterilization of wheat and brown rice by the equipment
-
Mineralogy And Raw Material Characterization Of Esie Stone ...
African Journals Online (AJOL)
Electronprobe mineral data of samples of Esie statues is presented as a possible tool for provenance studies. Most of the samples contain talc, chlorite, cummingtonite and rarely tremolite. Other talc-bearing schists are prevalent in the Esie area. However talc-cummingtonite rocks, similar to the raw materials used for the ...
-
Alternative of raw material’s suppliers using TOPSIS method in chicken slaughterhouse industry
Sari, R. M.; Rizkya, I.; Syahputri, K.; Anizar; Siregar, I.
2018-02-01
Chicken slaughterhouse industry is one of the fastest growing industries that depends on the freshness of raw materials. The raw materials quality arrive at the company depends heavily on the suppliers. Fresh chicken and frozen chicken meat are the main raw materials for this industry. Problems occurred by the suppliers are catering the amount of raw material needs that are not appropriate and also delay during delivery process. This condition causes disruption of the production process in the company. Therefore, it is necessary to determine the best suppliers to supply the main raw materials of fresh and frozen chicken meat on the slaughterhouse chicken industry. This study analyze the supplier’s capability by using TOPSIS method. This method use to find out the best supplier. The TOPSIS method is performed using the principle that chosen alternative must have the shortest distance from the positive solution and furthest from the ideal solution of the geometric point by using the Euclidean distance to determine the relative proximity of the optimum solution alternative. TOPSIS method found the rank of best supplier’s order is supplier A followed by supplier D, supplier B, supplier C, supplier E, supplier F, and supplier G. Based on the rank order obtained from each company, it will assist the company in prioritizing the order to the supplier with the best rank. Total supply from All suppliers are 885,994 kg per month. Based on the results of research, the top five suppliers have been sufficient to meet the needs of the company.
-
Impact of rearing conditions on the microbiological quality of raw retail poultry meat.
Hardy, Bridgshe; Crilly, Nate; Pendleton, Sean; Andino, Ana; Wallis, Audra; Zhang, Nan; Hanning, Irene
2013-08-01
There is a gap in knowledge of microbiological quality in raw chicken products produced by nonconventional methods and no studies have reported the microbiological quality of turkeys produced under different rearing environments. Thus, the aim of this study was to compare the microbiological quality of conventionally and organically reared whole chicken and turkey carcasses purchased from 3 retail outlets in Knoxville, Tenn., U.S.A. A total of 100 raw broiler chickens organically (n = 50) and 50 raw turkey carcasses consisting of 3 brands reared either conventionally (n = 25) or organically (n = 25) were evaluated. The FDA BAM protocol for rinsing poultry carcasses was used to enumerate of aerobic bacteria, Campylobacter, and Staphylococcus spp., and for qualitative analysis of Salmonella. Organic chickens from one brand had the highest average counts of aerobic bacteria, Staphylococcus spp. and Campylobacter (4.8, 4.8, and 4.7 Log10 CFU/mL rinsate, respectively) while the other organic brand had the lowest average counts (3.4, 3.3, and 3.1, respectively) of all 4 brands evaluated. The organic turkeys had the highest average counts of these same bacteria (4, 3.9, and 3.8, respectively) compared to the 2 brands of conventional turkeys evaluated. Salmonella (5% prevalence) was isolated only from organic chickens and turkeys. From these data, it appears that the microbiological quality of the raw product was not dependent on rearing conditions and, thus, it cannot be assumed that organic raw poultry is safer than conventionally raised poultry in terms of microbiological quality. © 2013 Institute of Food Technologists®
-
Raw material consumption of the European Union--concept, calculation method, and results.
Schoer, Karl; Weinzettel, Jan; Kovanda, Jan; Giegrich, Jürgen; Lauwigi, Christoph
2012-08-21
This article presents the concept, calculation method, and first results of the "Raw Material Consumption" (RMC) economy-wide material flow indicator for the European Union (EU). The RMC measures the final domestic consumption of products in terms of raw material equivalents (RME), i.e. raw materials used in the complete production chain of consumed products. We employed the hybrid input-output life cycle assessment method to calculate RMC. We first developed a highly disaggregated environmentally extended mixed unit input output table and then applied life cycle inventory data for imported products without appropriate representation of production within the domestic economy. Lastly, we treated capital formation as intermediate consumption. Our results show that services, often considered as a solution for dematerialization, account for a significant part of EU raw material consumption, which emphasizes the need to focus on the full production chains and dematerialization of services. Comparison of the EU's RMC with its domestic extraction shows that the EU is nearly self-sufficient in biomass and nonmetallic minerals but extremely dependent on direct and indirect imports of fossil energy carriers and metal ores. This implies an export of environmental burden related to extraction and primary processing of these materials to the rest of the world. Our results demonstrate that internalizing capital formation has significant influence on the calculated RMC.
-
Biosolubilization of raw and gamma irradiated lignite by trichoderma asperellum
International Nuclear Information System (INIS)
Sugoro, I.; Astuti, D.I.; Aditiawati, P.; Sasongko, D.
2012-01-01
Biosolubilization is a promising technology for converting solid coal to liquid oil by addition of microorganism. Aim of this research is to compare between gamma irradiated lignite (10 kGy) with raw lignite in biosolubilization by selected fungi Trichoderma asperellum. Treatments were A (MSS + gamma irradiated lignite 5% + T. asperellum) and B (MSS + raw lignite 5% + T. asperellum) with sub-merged culture. There were two parameters observed i.e. biosolubilization product based on absorbance value at λ 250nm and λ 450nm and metal analysis by neutron activation analysis (NAA). The highest biosolubilization will be analyzed by FTIR and GCMS. The results showed that biosolubilization of raw lignite (B) was higher than sterilized lignite (A) based on absorbance value at λ 250nm and λ 450nm . The metal of lignite was decreased after incubation. FTIR analysis showed that both of treatment had similar spectra on biosolubilization products. GCMS analysis showed that both of treatment had different number of hydrocarbon, i.e. C 6 - C 35 (A) and C 10 - C 35 (B) and dominated by aromatic acids, aliphatic and phenylethers. Both of treatment product had the potency as oil substituted but its recommended to deoxygenate for higher quality. (author)
-
Energy Technology Data Exchange (ETDEWEB)
Migdal, W.; Owczarczyk, H.B.; Malec-Czechowska, K.
1997-12-31
The results of investigations the electron beam irradiation on the microbial contamination of selected new generation cosmetics and raw products used in cosmetic industry are reported. The radiation doses applied were not higher than 6.0 kGy. The levels of microbial contamination were determined in irradiated and non-irradiated samples by standard methods routinely used. The results obtained show that radiation can be successfully used for decontamination of cosmetics and some of their raw materials, without changing the quality and applicability of the product. (author). 10 refs, 6 tabs.
-
Energy Technology Data Exchange (ETDEWEB)
Migdal, W; Owczarczyk, H B; Malec-Czechowska, K
1998-12-31
The results of investigations the electron beam irradiation on the microbial contamination of selected new generation cosmetics and raw products used in cosmetic industry are reported. The radiation doses applied were not higher than 6.0 kGy. The levels of microbial contamination were determined in irradiated and non-irradiated samples by standard methods routinely used. The results obtained show that radiation can be successfully used for decontamination of cosmetics and some of their raw materials, without changing the quality and applicability of the product. (author). 10 refs, 6 tabs.
-
Assessment of Gastroprotective Potential of Delonix regia (Boj Ex ...
African Journals Online (AJOL)
HP
(EDR) on ethanol and cold restrain stress-induced ulcer in experimental rats. Methods: EDR (100, 200 and 400 mg/kg doses, orally) was evaluated on ethanol and cold restrain ..... immune system leading to the release of the pro- inflammatory ...
-
Challenges and learning outcomes of educational design research for PhD students
Bronkhorst, L.H.; de Kleijn, R.A.M.
2016-01-01
Educational design research (EDR) is described as a complex research approach. The challenges resulting from this complexity are typically described as procedural, whereas EDR might also be challenging for different reasons, specifically for early career researchers. Yet challenging experiences may
-
The hygienic quality of raw reindeer milk
Directory of Open Access Journals (Sweden)
Joanna Kurki
2004-04-01
Full Text Available The somatic cell count (SCC and total bacterial count (TBC as well as the presence of major food-borne pathogens and udder pathogens in reindeer raw milk were studied. Two groups of 4 female reindeer were milked on alternate days for six weeks. A milk sample from each quarter was taken before milking and of the bulk milk at the end of milking. Micrococcus sp. was observed in one, Staphylococcus aureus in one and coagulase-negative staphylococci in five of the quarter samples (n=318. In the bulk milk (n=19 TBC varied between 700 and 1 700 000 cfu (colony forming units/ml and SCC between 52 000 and 183 000 cells/ml. No Bacillus cereus, S. aureus or Listeria monocytogenes were detected in the bulk milk, but Escherichia coli and Enterobacteriaceae were found in 5 bulk milk samples. According to the bacteriological examination the udder health of the reindeer was good. Indicative information on the SCC of healthy reindeer was obtained. None of the common potential food-poisoning bacteria were found in raw milk. There was great variation in the bulk milk TBC and the average TBC was rather high (ca. 300 000 cfu/ml. The hygienic quality of raw reindeer milk makes it well suited for food manufacture. However, the results indicate that the milking conditions may be crucial for the quality of raw milk.Abstract in Finnish / Yhteenveto:Tutkimuksen kohteena oli poron raakamaidon solupitoisuus ja kokonaispesäkeluku sekä tärkeimpien elintarvike- ja utarepatogeenien esiintyminen raakamaidossa. Kaksi 4 vaatimen ryhmää lypsettiin vuoropäivinä 6 viikon ajan. Ennen lypsyä vaatimista otettiin vedinkohtaiset näytteet ja lypsyn päätyttyä näyte yhteismaidosta. Micrococcus sp. todettiin yhdessä, Staphylococcus aureus yhdessä ja koagulaasinegatiivisia stafylokokkeja viidessä vedinkohtaisessa näytteessä (n=318. Yhteismaitonäytteiden (n=19 kokonaispesäkeluvut vaihtelivat välillä 700-1 700 000 pmy (pesäkkeitä muodostava yksikkö/ml ja somaattisten
-
Hydrolytic potential of a psychrotrophic Pseudomonas isolated from refrigerated raw milk
Directory of Open Access Journals (Sweden)
Ana Paula F. Corrêa
2011-12-01
Full Text Available The production of extracellular hydrolases by a psychrotrophic bacterium isolated from refrigerated raw milk, and identified as a Pseudomonas sp. belonging to the Pseudomonas jenssenii group, was studied. This bacterium produced proteolytic and lipolytic enzymes in all media investigated (skim milk, cheese whey, casein broth, and tryptone soy broth. High levels of α-glucosidase were produced in skim milk broth. Hydrolytic enzymes detected in skim milk broth are of particular concern, indicating that these enzymes could be produced by Pseudomonas sp. during the cold storage of raw milk, contributing to the spoilage problem in milk and dairy products.
-
Raw material selection for object construction
CSIR Research Space (South Africa)
Perlow, J
2017-11-01
Full Text Available on their visual appearance. In particular, we present a method for an agent to recognise the required unseen raw material images and link them to corresponding novel object images. This capability provides an agent with an increased degree of resourcefulness... construction from component parts, and in doing so we provide a benchmark for future work to compare against within Minecraft and ShapeNet domains. II. BACKGROUND Our model is inspired by Siamese neural networks, a class of neural network that includes multiple...
-
Microbes from raw milk for fermented dairy products
Wouters, J.T.M.; Ayad, E.H.E.; Hugenholtz, J.; Smit, G.
2002-01-01
Milk has a high nutritive value, not only For the new-born mammal and for the human consumer, but also for microbes. Raw milk kept at roam temperature will be liable to microbial spoilage. After some days, the milk will spontaneously become sour. This is generally due to the activity of lactic acid
-
Directory of Open Access Journals (Sweden)
F. Tonucci
2009-09-01
Full Text Available In the last years, direct sale of raw milk by vending machines has largely increased in several European Countries and Italy. As a consequence, adequate hygienic measures and correct consumer’s information is required in order to reduce any potential risk linked to this product. In the present study, the occurrence of pathogens (Salmonella spp., verocytotoxigenic E.coli, Campylobacter spp., Listeria monocytogenes, S.aureus in raw milk and bovine faeces collected in 4 farms in the province of Pesaro-Urbino (Italy, between January 2007 and March 2009 has been investigated; 99.5% of milk samples resulted negative for the pathogens considered and complying with the regulation S. aureus limits. Campylobacter has been found in 0.44% of the samples, collected during summer, while only one sample resulted positive to a non-verocytotoxigenic E.coli O157. In respect to faeces, 62.6% of the samples resulted negative, 33.6% were contaminated by Campylobacter spp. (68% Campylobacter coli and 32% Campylobacter jejuni and 3.8% by E.coli O157. No samples resulted positive for Salmonella spp. or Listeria monocytogenes. The results highlight the necessity of a strict plan of hygienic and sanitary controls, with particular attention to milking process hygiene and raw milk storage, to reduce the risk of contamination of the product.
-
CONCENTRATION OF SELECTED ELEMENTS IN RAW AND ULTRA HEAT TREATED COW MILK
Directory of Open Access Journals (Sweden)
Lukáčová Anetta
2012-10-01
Full Text Available The potential presence of toxic metals in food is being recognized as a priority by standards organizations and constitutes an analytical challenge. The toxic metal content of milk and dairy products is due to several factors: environmental conditions, the manufacturing process and the possible contamination during several steps of the manufacturing processes. The aim of this study was to evaluate samples of raw milk with fat contents 3.8% obtained at randomly from animal farms in around Nitra, western Slovakia region and ultra – heat treated cow milk (UHT with fat contents 1.5% commercially available from local market in Nitra. Samples of milk were analysed for metal contents using atomic absorption spectrophotometry (AAS. UHT milk showed higher levels of cadmium, nickel and iron. Higher levels of zinc, copper were detected in raw milk. Significant differences in the concentration of copper between raw and UHT cow milk were found.
-
Viability of Ascaris suum eggs in stored raw and separated liquid slurry
DEFF Research Database (Denmark)
Katakam, Kiran Kumar; Roepstorff, Allan Knud; Popovic, Olga
2013-01-01
SUMMARY Separation of pig slurry into solid and liquid fractions is gaining importance as a way to manage increasing volumes of slurry. In contrast to solid manure and slurry, little is known about pathogen survival in separated liquid slurry. The viability of Ascaris suum eggs, a conservative...... indicator of fecal pollution, and its association with ammonia was investigated in separated liquid slurry in comparison with raw slurry. For this purpose nylon bags with 6000 eggs each were placed in 1 litre bottles containing one of the two fractions for 308 days at 5 °C or 25 °C. Initial analysis...... of helminth eggs in the separated liquid slurry revealed 47 Ascaris eggs per gramme. At 25 °C, egg viability declined to zero with a similar trend in both raw slurry and the separated liquid slurry by day 308, a time when at 5 °C 88% and 42% of the eggs were still viable in separated liquid slurry and raw...
-
Contamination levels of aflatoxin M1 in bulk raw milk of Chaloos and Ramsar
Directory of Open Access Journals (Sweden)
A.R Barami
2012-02-01
Full Text Available Aflatoxin M1 (AFM1 appears in milk as a direct result of the ingestion of feed contaminated with aflatoxin B1 by cattle. This study was conducted to investigate the contamination rate of raw milk whit aflatoxin M1 in Chaloos and Ramsar raw milk collection centers. Two hundred bulk raw milk samples were collected during winter (January and February and summer (June and July seasons. The milk samples were analyzed by ELISA method for the presence of AFM1. During the winter, AFM1 was detected in 100% and 59/79% of the bulk raw milk samples in Ramsar and Chaloos, respectively; however, during summer 83/52% and 50/1 of the samples was found as positive in Ramsar and Chaloos, respectively. Furthermore, 45% of Ramsar and 30% of Chaloos bulk milk samples showed higher contamination level of AFM1 than maximum tolerance limit (50 ng/l accepted by National Standard as well as European Union. Although, the difference between the contamination rate in samples obtained during summer and winter seasons was not statistically significantly, (p
-
Matali, Sharmeela; Rahman, Norazah Abdul; Idris, Siti Shawaliah; Yaacob, Nurhafizah
2017-12-01
Torrefaction, also known as mild pyrolysis, is proven to convert raw biomass into a value-added energy commodity particularly for application in combustion and co-firing systems with improved storage and handling properties. This paper aims to compare the characteristics of Malaysian bituminous coal i.e. Silantek coal with raw and torrefied biomass pellet originated from oil palm frond and fast growing tree species, Leucaena Leucocephala. Biomass samples were initially torrefied at 300 °C for 60 minutes. Resulting torrefied biomass pellets were analysed using a number of standard fuel characterisation analyses i.e. elemental analysis, proximate analysis and calorific content (high heating values) experiments. Investigations on combustion characteristics via dynamic thermogravimetric analysis (TGA), grindability and moisture uptake tests were also performed on the torrefied biomass pellets. Better quality bio-chars were produced as compared to its raw forms and with optimal process conditions, torrefaction may potentially produces a solid fuel with combustion reactivity and porosity equivalent to raw biomass while having compatible energy density and grindability to coal.
-
Complex and rational use fish raw material at production of the fish products
Saltanova, N.; Saltanov, D.
2011-01-01
There was developed resource saving technology of herring preserves, which allows to rationally use raw, to cut lasting of the technological process, to lower the production costs and rise the economical effectiveness of production. There were defined the optimal conditions of getting broths of herring wastes. There were developed the recipes of fills at the base of broth from collagen-containing wastes of herring with the addition of vegetable raw.
-
CONTRIBUTION TO THE STATISTICAL INTERPRETATION OF RAW MATERIALS FOR THE CEMENT INDUSTRY OF SPLIT
Directory of Open Access Journals (Sweden)
Miroslav Matijaca
1990-12-01
Full Text Available Up to the last two decades cement was produced from mari called »tupina« (with about 76% CaCOj which is an ideal mixture for cement production. Due to the quantity decrease of this raw material, cement production went on using the mixture of other members of the flysch series: limestones, marls, clay, loess, sandstones a.o. By the analysis of natural materials the CaCO^ content has mostly been proved. Therefore, knowing the correlation of oxides in mineral raw material is of special significance. The article discusses investigation results of the correlation between CaCO-i and other oxides of the raw material (the paper is published in Croatian.
-
2010-04-27
... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 200,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2010 raw sugar tariff-rate quota (TRQ) by...
-
2011-04-15
...-Rate Quota Volume for Raw Cane Sugar and Reallocation of Unused Fiscal Year 2011 Tariff-Rate Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar and of country-by-country reallocations of the FY 2011 in-quota quantity...
-
2011-08-12
... for Raw Cane Sugar, Refined and Specialty Sugar and Sugar-Containing Products AGENCY: Office of the... quantity of the tariff-rate quotas for imported raw cane sugar, refined and specialty sugar and sugar...), the United States maintains tariff-rate quotas (TRQs) for imports of raw cane sugar and refined sugar...
-
2010-07-06
... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2010 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 300,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2010 raw sugar tariff-rate quota (TRQ) by...
-
2012-04-26
...-Rate Quota Volume for Raw Cane Sugar and Reallocation of Unused Fiscal Year 2012 Tariff-Rate Quota Volume for Raw Cane Sugar AGENCY: Office of the United States Trade Representative. ACTION: Notice...) for imported raw cane sugar and of country-by-country reallocations of the FY 2012 in-quota quantity...
-
2011-04-12
... USDA Reassigns Domestic Cane Sugar Allotments and Increases the Fiscal Year 2011 Raw Sugar Tariff-Rate... announced a reassignment of surplus sugar under domestic cane sugar allotments of 325,000 short tons raw value (STRV) to imports, and increased the fiscal year (FY) 2011 raw sugar tariff-rate quota (TRQ) by...
-
Use of basaltic waste as red ceramic raw material
Directory of Open Access Journals (Sweden)
T. M. Mendes
Full Text Available Abstract Nowadays, environmental codes restrict the emission of particulate matters, which result in these residues being collected by plant filters. This basaltic waste came from construction aggregate plants located in the Metropolitan Region of Londrina (State of Paraná, Brazil. Initially, the basaltic waste was submitted to sieving (< 75 μm and the powder obtained was characterized in terms of density and particle size distribution. The plasticity of ceramic mass containing 0%, 10%, 20%, 30%, 40% and 50% of basaltic waste was measured by Atterberg method. The chemical composition of ceramic formulations containing 0% and 20% of basaltic waste was determined by X-ray fluorescence. The prismatic samples were molded by extrusion and fired at 850 °C. The specimens were also tested to determine density, water absorption, drying and firing shrinkages, flexural strength, and Young's modulus. Microstructure evaluation was conducted by scanning electron microscopy, X-ray diffraction, and mercury intrusion porosimetry. Basaltic powder has similar physical and chemical characteristics when compared to other raw materials, and contributes to ceramic processing by reducing drying and firing shrinkage. Mechanical performance of mixtures containing basaltic powder is equivalent to mixtures without waste. Microstructural aspects such as pore size distribution were modified by basaltic powder; albite phase related to basaltic powder was identified by X-ray diffraction.
-
Directory of Open Access Journals (Sweden)
E. Kardas
2017-01-01
Full Text Available The paper analyses the quality of raw materials used in the production of blast furnace pig iron. The ferruginous sinter and pellets are the basic raw materials used in the process. The paper presents the impact of those raw materials quality on the effectiveness of the blast furnace process. The process effectiveness will be specified by means of selected process parameters.
-
40 CFR 63.1344 - Operating limits for kilns and in-line kiln/raw mills.
2010-07-01
... kiln/raw mills. 63.1344 Section 63.1344 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... mills. (a) The owner or operator of a kiln subject to a D/F emission limitation under § 63.1343 must... specified in paragraph (b) of this section. The owner or operator of an in-line kiln/raw mill subject to a D...
-
Preliminary treatment of MSW fly ash as a way of improving electrodialytic remediation
DEFF Research Database (Denmark)
Ferreira, Célia Maria Dias; Jensen, Pernille Erland; Ottosen, Lisbeth M.
2008-01-01
In the current work electrodialytic remediation (EDR) was applied to remove heavy metals from municipal solid waste (MSW) fly ash, a hazardous waste collected during flue gas treatment. Tests were conducted to evaluate if EDR could be improved by introducing a preliminary treatment in which very...... soluble salts were removed. Three different preliminary treatments were conducted with different L:S ratios and pH. Treatment in which metal release and L/S ratio were lower was selected for EDR. Electrodialytic remediation was performed at a constant current of 38 mA, for 14 days, using gluconate...... as a solubilisation enhancement agent. Conductivity and pH were monitored and electrolyte samples were collected every 4 days to evaluate metal release over time. It was found that the preliminary treatment reduces fouling of the ion-exchange membranes used in EDR and drastically increases the removal of metals...
-
XENOBIOTICS AND BIOGENIC ELEMENTS IN RAW COW'S MILK
Directory of Open Access Journals (Sweden)
Agnieszka Greń
2012-12-01
Full Text Available Normal 0 21 false false false SK X-NONE X-NONE This paper presents the concentration some toxic and biogenic elements in milk from Nitra region. The aim of this investigation was to evaluate 30 samples of raw milk with fat contents 3.8% obtained from milk machine in the Nitra region. Samples were analyzed for metal contents using atomic absorption spectrophotometry (AAS. In comparison with maximum acceptable concentration for milk in the food codex of the Slovak republic, the level of contamination with cadmium was exceeded and reached the value 0.221 µg.ml-1. The copper content ranged from 1.201 µg.ml-1 to 5.810 µg.ml-1 and the average concentration reached 3.793 µg.ml-1. Iron had an average of 1.824 µg.ml-1. Overall in all milk samples high correlations were found. Between positive correlation (0.7019 and negative correlation between of nickel and potassium concentration in raw milk (-0.72 was found. doi:10.5219/246
-
Radioactivity in polluted cement and its raw materials
International Nuclear Information System (INIS)
Khan, K.; Aslam, M.; Orfi, S.D.
1999-01-01
Samples of portland cement manufactured in the North West frontier Province (NWFP) of Pakistan and its different raw materials have been investigated applying gamma-spectrometric techniques for natural gamma-emitting radionuclides. A high purity germanium detector (HPGE) was used for data acquisition. Average values of the total specific activity (in Bq.kg/sup -1/ ) due to all the three radionuclides (/sub 40/K, /sup 226/Ra and /sup 232/Th) were found to be 327.7+ - 168.2 for portland cement; 104.4 + - 21.1 for limestone; 193.2+ - 50.4 for gypsum; 890.4 + - 86.5 for state and 545.6+ - 56.6 for latrite. The average specific activities due to /sup 40/K in Portland cement and all the raw materials were found to be higher as compared to /sub 226/Ra and /sup 232/Th in the respective materials. It is concluded that such materials do not pose any health problem and are not a major source of radiation hazards. However, The data can be utilized in determining radioactivity associated with other building materials. (author)
-
Contamination of the cement raw material in a quarry site by seawater intrusion, Darica-Turkey
Camur, M. Zeki; Doyuran, Vedat
2008-02-01
The open pit mining nearby shoreline is planned to be extended into below sea level in order to use additional reserves of the cement raw material (marl). The raw material is currently contaminated by seawater intrusion below a depth of 20 m up to the distance of 90 m from shoreline. Seawater intrusion related contamination of the material used for the cement production was investigated by means of diffusion process for the future two below sea level mining scenarios covering 43 years of period. According to the results, chloride concentrations higher than the tolerable limit of a cement raw material would be present in the material about 10-25 cm inward from each discontinuity surface, controlling groundwater flow, located between 170 and 300 m landward from the shoreline at below sea level mining depths of 0-30 m. The estimations suggest that total amounts of dilution required for the contaminated raw material to reduce its concentration level to the tolerance limit with uncontaminated raw material are about 113- to 124-fold for scenario I (13 years of below sea level mining after 30 years of above sea level mining) and about 126- to 138-fold for scenario II (43 years of simultaneous above and below sea level minings).
-
Thorium and Uranium in the Rock Raw Materials Used For the Production of Building Materials
Pękala, Agnieszka
2017-10-01
Thorium and uranium are constant components of all soils and most minerals thereby rock raw materials. They belong to the particularly dangerous elements because of their natural radioactivity. Evaluation of the content of the radioactive elements in the rock raw materials seems to be necessary in the early stage of the raw material evaluation. The rock formations operated from deposits often are accumulated in landfills and slag heaps where the concentration of the radioactive elements can be many times higher than under natural conditions. In addition, this phenomenon may refer to buildings where rock raw materials are often the main components of the construction materials. The global control system of construction products draws particular attention to the elimination of used construction products containing excessive quantities of the natural radioactive elements. In the presented study were determined the content of thorium and uranium in rock raw materials coming from the Bełachatów lignite deposit. The Bełchatów lignite deposit extracts mainly lignite and secondary numerous accompanying minerals with the raw material importance. In the course of the field works within the framework of the carried out work has been tested 92 samples of rocks of varied petrographic composition. There were carried out analyses of the content of the radioactive elements for 50 samples of limestone of the Jurassic age, 18 samples of kaolinite clays, and 24 samples of siliceous raw materials, represented by opoka-rocks, diatomites, gaizes and clastic rocks. The measurement of content of the natural radioactive elements thorium and uranium based on measuring the frequency counts of gamma quantum, recorded separately in measuring channels. At the same time performed measurements on volume patterns radioactive: thorium and uranium. The studies were carried out in Mazar spectrometer on the powdered material. Standardly performed ten measuring cycles, after which were calculated
-
Rare earth elements exploitation, geopolitical implications and raw materials trading
Chemin, Marie-Charlotte
2015-04-01
Rare earth elements (REE) correspond to seventeen elements of the periodic table. They are used in high technology, cracking, electric cars' magnet, metal alloy for batteries, and also in phone construction or ceramics for electronic card. REEs are an important resource for high technology. This project targets 16 years old students in the subject "personalized aid" and will last six weeks. The purpose of this project is to develop autonomy and research in groups for a transdisciplinary work. This project gathers knowledge in geology, geography and economics. During the first session students analyze the geology applications of the REE. They begin the analysis with learning the composition in different rocks such as basalt and diorite to make the link with crystallization. Then they compare it with adakite to understand the formation of these rocks. In the second session, they study REE exploitation. We can find them as oxides in many deposits. The principal concentrations of rare earth elements are associated with uncommon varieties of igneous rocks, such as carbonatites. They can use Qgis, to localize this high concentration. In the third session, they study the environmental costs of REE exploitation. Indeed, the exploitation produces thorium and carcinogenic toxins: sulphates, ammonia and hydrochloric acid. Processing one ton of rare earths produces 2,000 tons of toxic waste. This session focuses, first, on Baotou's region, and then on an example they are free to choose. In the fourth session, they study the geopolitical issues of REE with a focus on China. In fact this country is the largest producer of REE, and is providing 95% of the overall production. REE in China are at the center of a geopolitical strategy. In fact, China implements a sort of protectionism. Indeed, the export tax on REE is very high so, as a foreign company, it is financially attractive to establish a manufacturing subsidiary in China in order to use REE. As a matter of fact
-
IceBridge IMU L0 Raw Inertial Measurement Unit Data
National Aeronautics and Space Administration — The NASA IceBridge IMU L0 Raw Inertial Measurement Unit Data (IPUTI0) data set contains Inertial Measurement Unit (IMU) readings, including latitude, longitude,...
-
Endoplasmic Reticulum Stress Cooperates in Zearalenone-Induced Cell Death of RAW 264.7 Macrophages
Directory of Open Access Journals (Sweden)
Fenglei Chen
2015-08-01
Full Text Available Zearalenone (ZEA is a fungal mycotoxin that causes cell apoptosis and necrosis. However, little is known about the molecular mechanisms of ZEA toxicity. The objective of this study was to explore the effects of ZEA on the proliferation and apoptosis of RAW 264.7 macrophages and to uncover the signaling pathway underlying the cytotoxicity of ZEA in RAW 264.7 macrophages. This study demonstrates that the endoplasmic reticulum (ER stress pathway cooperated in ZEA-induced cell death of the RAW 264.7 macrophages. Our results show that ZEA treatment reduced the viability of RAW 264.7 macrophages in a dose- and time-dependent manner as shown by the 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide assay (MTT and flow cytometry assay. Western blots analysis revealed that ZEA increased the expression of glucose-regulated protein 78 (GRP78 and CCAAT/enhancer binding protein homologous protein (CHOP, two ER stress-related marker genes. Furthermore, treating the cells with the ER stress inhibitors 4-phenylbutyrate (4-PBA or knocking down CHOP, using lentivirus encoded short hairpin interfering RNAs (shRNAs, significantly diminished the ZEA-induced increases in GRP78 and CHOP, and cell death. In summary, our results suggest that ZEA induces the apoptosis and necrosis of RAW 264.7 macrophages in a dose- and time-dependent manner via the ER stress pathway in which the activation of CHOP plays a critical role.
-
Directory of Open Access Journals (Sweden)
Yi Lv
2014-01-01
Full Text Available Nonneuronal cholinergic system plays a primary role in maintaining homeostasis. It has been proved that endogenous neuronal acetylcholine (ACh could play an anti-inflammatory role, and exogenous cholinergic agonists could weaken macrophages inflammatory response to lipopolysaccharide (LPS stimulation through activation of α7 subunit-containing nicotinic acetylcholine receptor (α7nAChR. We assumed that nonneuronal cholinergic system existing in macrophages could modulate inflammation through autocrine ACh and expressed α7nAChR on the cells. Therefore, we explored whether LPS continuous stimulation could upregulate the nonneuronal cholinergic activity in macrophages and whether increasing autocrine ACh could decrease TNF release from the macrophages. The results showed that, in RAW264.7 cells incubated with LPS for 20 hours, the secretion of ACh was significantly decreased at 4 h and then gradually increased, accompanied with the enhancement of α7nAChR expression level. The release of TNF was greatly increased from RAW264.7 cells at 4 h and 8 h exposure to LPS; however, it was suppressed at 20 h. Upregulating choline acetyltransferase (ChAT expression through ChAT gene transfection could enhance ACh secretion and reduce TNF release from the infected RAW264. 7cells. The results indicated that LPS stimulation could modulate the activity of nonneuronal cholinergic system of RAW264.7 cells. Enhancing autocrine ACh production could attenuate TNF release from RAW264.7 cells.