WorldWideScience

Sample records for rapid prototyping methods

  1. Methods and systems for rapid prototyping of high density circuits

    Science.gov (United States)

    Palmer, Jeremy A [Albuquerque, NM; Davis, Donald W [Albuquerque, NM; Chavez, Bart D [Albuquerque, NM; Gallegos, Phillip L [Albuquerque, NM; Wicker, Ryan B [El Paso, TX; Medina, Francisco R [El Paso, TX

    2008-09-02

    A preferred embodiment provides, for example, a system and method of integrating fluid media dispensing technology such as direct-write (DW) technologies with rapid prototyping (RP) technologies such as stereolithography (SL) to provide increased micro-fabrication and micro-stereolithography. A preferred embodiment of the present invention also provides, for example, a system and method for Rapid Prototyping High Density Circuit (RPHDC) manufacturing of solderless connectors and pilot devices with terminal geometries that are compatible with DW mechanisms and reduce contact resistance where the electrical system is encapsulated within structural members and manual electrical connections are eliminated in favor of automated DW traces. A preferred embodiment further provides, for example, a method of rapid prototyping comprising: fabricating a part layer using stereolithography and depositing thermally curable media onto the part layer using a fluid dispensing apparatus.

  2. Rapid Prototyping

    Science.gov (United States)

    1999-01-01

    Javelin, a Lone Peak Engineering Inc. Company has introduced the SteamRoller(TM) System as a commercial product. The system was designed by Javelin during a Phase II NASA funded small commercial product. The purpose of the invention was to allow automated-feed of flexible ceramic tapes to the Laminated Object Manufacturing rapid prototyping equipment. The ceramic material that Javelin was working with during the Phase II project is silicon nitride. This engineered ceramic material is of interest for space-based component.

  3. Rapid prototype and test

    Energy Technology Data Exchange (ETDEWEB)

    Gregory, D.L.; Hansche, B.D.

    1996-06-01

    In order to support advanced manufacturing, Sandia has acquired the capability to produce plastic prototypes using stereolithography. Currently, these prototypes are used mainly to verify part geometry and ``fit and form`` checks. This project investigates methods for rapidly testing these plastic prototypes, and inferring from prototype test data actual metal part performance and behavior. Performances examined include static load/stress response, and structural dynamic (modal) and vibration behavior. The integration of advanced non-contacting measurement techniques including scanning laser velocimetry, laser holography, and thermoelasticity into testing of these prototypes is described. Photoelastic properties of the epoxy prototypes to reveal full field stress/strain fields are also explored.

  4. Rapid Prototyping Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The ARDEC Rapid Prototyping (RP) Laboratory was established in December 1992 to provide low cost RP capabilities to the ARDEC engineering community. The Stratasys,...

  5. Rapid prototyping in medical sciences

    Directory of Open Access Journals (Sweden)

    Ákos Márk Horváth

    2015-09-01

    Full Text Available Even if it sound a bit incredible rapid prototyping (RPT as production method has been used for decades in other professions. Nevertheless medical science just started discover the possibilities of this technology and use the offered benefits of 3D printing. In this paper authors have investigated the pharmaceutical usage of rapid prototyping.

  6. The scope of application of incremental rapid prototyping methods in foundry engineering

    Directory of Open Access Journals (Sweden)

    M. Stankiewicz

    2010-01-01

    Full Text Available The article presents the scope of application of selected incremental Rapid Prototyping methods in the process of manufacturing casting models, casting moulds and casts. The Rapid Prototyping methods (SL, SLA, FDM, 3DP, JS are predominantly used for the production of models and model sets for casting moulds. The Rapid Tooling methods, such as: ZCast-3DP, ProMetalRCT and VoxelJet, enable the fabrication of casting moulds in the incremental process. The application of the RP methods in cast production makes it possible to speed up the prototype preparation process. This is particularly vital to elements of complex shapes. The time required for the manufacture of the model, the mould and the cast proper may vary from a few to several dozen hours.

  7. Rapid prototyping methods for the manufacture of fuel cells

    Directory of Open Access Journals (Sweden)

    Dudek Piotr

    2016-01-01

    The potential for the application of this method for the manufacture of metallic bipolar plates (BPP for use in proton exchange membrane fuel cells (PEMFCs is presented and discussed. Special attention is paid to the fabrication of light elements for the construction of PEMFC stacks designed for mobile applications such as aviation technology and unmanned aerial vehicles (UAVs.

  8. Rapid Prototyping in PVS

    Science.gov (United States)

    Munoz, Cesar A.; Butler, Ricky (Technical Monitor)

    2003-01-01

    PVSio is a conservative extension to the PVS prelude library that provides basic input/output capabilities to the PVS ground evaluator. It supports rapid prototyping in PVS by enhancing the specification language with built-in constructs for string manipulation, floating point arithmetic, and input/output operations.

  9. Rapid Prototyping Reconsidered

    Science.gov (United States)

    Desrosier, James

    2011-01-01

    Continuing educators need additional strategies for developing new programming that can both reduce the time to market and lower the cost of development. Rapid prototyping, a time-compression technique adapted from the high technology industry, represents one such strategy that merits renewed evaluation. Although in higher education rapid…

  10. Performance of a Micro-UAV lifting system built with the usage of rapid prototyping methods

    Science.gov (United States)

    Dalewski, R. T.; Gumowski, K.; Barczak, T.; Godek, J.

    2014-08-01

    This article presents results of the aerodynamic testing of a micro unmanned aerial vehicle rotor efficiency. The rotors were prepared as a set of two rotors in a counter-rotating ducted drive. Prototypes of the drives were made using two rapid prototyping techniques - FDM - fused deposition modelling method and SLS - selective laser sintering. Rotors were made then treated by introducing additional finishing cyanoacrylate coating and abrasive processing. Main differences between those models were observed in fan shape, porosity, surface roughness and mechanical properties - stiffness. An influence of these factors was observed on an aerodynamic efficiency. For the obtained prototypes both simulations and experimental testing were conducted with thrust, power, torque measurements, as well as the measurement of velocity and pressure distribution at the outlet of the duct. The results show the possibility of using rapid prototyping techniques to produce prototypes of drives operating in the low and medium Reynolds numbers (6000-60000), and the aerodynamic shape relevant factors affecting the preparation and performance of such drives. In addition, simulation studies were performed using the Fluent environment where experimental results were confronted with the results of simulation studies.

  11. Composites by rapid prototyping technology

    CSIR Research Space (South Africa)

    Kumar, S

    2010-02-01

    Full Text Available powder is a fiber, problems of manufacturing occur. The method has also been used to make Metal Matrix Composite (MMC), e.g Fe and graphite [17], WC-Co [18,19], WC-Co and Cu [20,21], Fe, Ni and TiC [22] etc and Ceramic Matrix Composite (CMC) e.g. Si... of various materials used. Key words: : Rapid Prototyping (RP), Laser, Composites 1 Introduction Rapid Prototyping (RP) initially focussed on polymers. These were later re- placed/supplemented by ceramics, metals and composites. Composites are used in RP...

  12. FLASH: A rapid method for prototyping paper-based microfluidic devices‡

    Science.gov (United States)

    Martinez, Andres W.; Phillips, Scott T.; Wiley, Benjamin J.; Gupta, Malancha

    2011-01-01

    This article describes FLASH (Fast Lithographic Activation of Sheets), a rapid method for laboratory prototyping of microfluidic devices in paper. Paper-based microfluidic devices are emerging as a new technology for applications in diagnostics for the developing world, where low cost and simplicity are essential. FLASH is based on photolithography, but requires only a UV lamp and a hotplate; no clean-room or special facilities are required (FLASH patterning can even be performed in sunlight if a UV lamp and hotplate are unavailable). The method provides channels in paper with dimensions as small as 200 μm in width and 70 μm in height; the height is defined by the thickness of the paper. Photomasks for patterning paper-based microfluidic devices can be printed using an ink-jet printer or photocopier, or drawn by hand using a waterproof black pen. FLASH provides a straightforward method for prototyping paper-based microfluidic devices in regions where the technological support for conventional photolithography is not available. PMID:19023478

  13. Rapid Prototyping of Mobile Learning Games

    Science.gov (United States)

    Federley, Maija; Sorsa, Timo; Paavilainen, Janne; Boissonnier, Kimo; Seisto, Anu

    2014-01-01

    This position paper presents the first results of an on-going project, in which we explore rapid prototyping method to efficiently produce digital learning solutions that are commercially viable. In this first phase, rapid game prototyping and an iterative approach was tested as a quick and efficient way to create learning games and to evaluate…

  14. Rapid prototyping tools and methods for all-Topas (R) cyclic olefin copolymer fluidic microsystems

    DEFF Research Database (Denmark)

    Bundgaard, Frederik; Perozziello, Gerardo; Geschke, Oliver

    2006-01-01

    Topas (R), the cyclic olefin copolymer, from Topas Advanced Polymers GmbH has a number of advantages over polymers such as poly(methylmethacrylate), polydimethylsiloxane, and polycarbonate traditionally used in fluid microsystem manufacturing, such as low water absorption, high chemical resistance......, good machinability, and good optical properties. A number of different processes for rapid and low-cost prototyping of all-Topas microfluidic systems, made with desktop machinery, are presented. Among the processes are micromilling of fluidic structures with a width down to 25 p,m and sealing...

  15. Selective laser sintering: application of a rapid prototyping method in craniomaxillofacial reconstructive surgery.

    Science.gov (United States)

    Aung, S C; Tan, B K; Foo, C L; Lee, S T

    1999-09-01

    Advances in technology have benefited the medical world in many ways and a new generation of computed tomography (CT) scanners and three-dimensional (3-D) model making rapid prototyping systems (RPS) have taken craniofacial surgical planning and management to new heights. With the development of new rapid prototyping systems and the improvements in CT scan technology, such as the helical scanner, biomedical modelling has improved considerably and accurate 3-D models can now be fabricated to allow surgeons to visualise and physically handle a 3-D model on which simulation surgery can be performed. The principle behind this technology is to first acquire digital data (CT scan data) which is then imported to the RPS to fabricate fine layers or cuts of the model which are gradually built up to form the 3-D models. Either liquid resin or nylon powder or special paper may be used to make these models using the various RPS available today. Selective laser sintering (SLS), which employs a CO2 laser beam to solidify special nylon powder and build up the model in layers is described in this case report, where a 23-year old Chinese female with panfacial fracture and a skull defect benefited from SLS biomodelling in the preoperative workup.

  16. Rapid prototyping tools

    OpenAIRE

    Birkeland, Petter I

    2016-01-01

    This paper is the description of the method and result of the master project of Petter Ildgruben at the Department of Engineering Design and Materials (IPM) at the Norwegian University of Science and Technology (NTNU) in the spring of 2016. The goal of this master s thesis has been to explore the barriers that novel users face in makerspaces, specifically when interacting with the 3D printer, the laser cutter and the Computer Numerical Control (CNC) mill and how to overcome them. The first...

  17. [Computer-aided method and rapid prototyping for the personalized fabrication of a silicone bandage digital prosthesis].

    Science.gov (United States)

    Ventura Ferreira, Nuno; Leal, Nuno; Correia Sá, Inês; Reis, Ana; Marques, Marisa

    2014-01-01

    The fabrication of digital prostheses has acquired growing importance not only for the possibility for the patient to overcome psychosocial trauma but also to promote grip functionality. An application method of three dimensional-computer-aided design technologies for the production of passive prostheses is presented by means of a fifth finger amputee clinical case following bilateral hand replantation.Three-dimensional-computerized tomography was used for the collection of anthropometric images of the hands. Computer-aided design techniques were used to develop the digital file-based prosthesis from the reconstruction images by inversion and superimposing the contra-lateral finger images. The rapid prototyping manufacturing method was used for the production of a silicone bandage prosthesis prototype. This approach replaces the traditional manual method by a virtual method that is basis for the optimization of a high speed, accurate and innovative process.

  18. Development and tendency of rapid prototyping technology

    Science.gov (United States)

    Yan, Yongnian; Hong, Guodong

    1998-08-01

    The definition of the rapid prototyping is given in this paper. Various RP processes, which build the prototypes with 2.5 or 3 dimensional layers, are introduced. The relative techniques of RP and the differences between RP technique and CNC manufacturing are analyzed. The paper discusses the RP's applied fields and methods and presents the RP development in the world. According to the idea that requirements determine the developing, the RP's tendency is discussed.

  19. Ceramic microfabrication by rapid prototyping process chains

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    fast and inexpensive supply for polymer master models and a ceramic shaping method that enables the replication of the RP model into multiple ceramic materials within a short time. (Knitter et al 1999). 2. Rapid prototyping process chains. The manufacturing of ceramic microparts presented here set out with the 3D-CAD ...

  20. Rapid Prototyping: Technologies, Materials and Advances

    Directory of Open Access Journals (Sweden)

    Dudek P.

    2016-06-01

    Full Text Available In the context of product development, the term rapid prototyping (RP is widely used to describe technologies which create physical prototypes directly from digital data. Recently, this technology has become one of the fastest-growing methods of manufacturing parts. The paper provides brief notes on the creation of composites using RP methods, such as stereolithography, selective laser sintering or melting, laminated object modelling, fused deposition modelling or three-dimensional printing. The emphasis of this work is on the methodology of composite fabrication and the variety of materials used in these technologies.

  1. Rapid and accurate assembly method for a new Laue lens prototype

    Science.gov (United States)

    Wade, Colin; Barrière, Nicolas; Hanlon, Lorraine; Boggs, Steven E.; Brejnholt, Nicolai F.; Massahi, Sonny; Tomsick, John A.; von Ballmoos, Peter

    2015-09-01

    The Laue lens is a technology for gamma-ray astrophysics whereby gamma-rays of particular energies can be focused by a suitable arrangement of crystals. The Laue lens assembly station at UC Berkeley was used to build a technological demonstrator addressing the key issues of crystal mounting speed, crystal position and orientation accuracy, and crystal reflectivity. The new prototype is a lens segment containing a total of 48 5 x 5 mm2 crystals - 36 Iron and 12 Aluminium. The segment is composed of 8 partial rings, each of which is aligned to diffract an energy between 95 and 130 keV from a source at 12:5m with a focal length of 1:5 m.

  2. Rapid Prototyping in Instructional Design: Creating Competencies

    Science.gov (United States)

    Fulton, Carolyn D.

    2010-01-01

    Instructional designers working in rapid prototyping environments currently do not have a list of competencies that help to identify the knowledge, skills, and attitudes (KSAs) required in these workplaces. This qualitative case study used multiple cases in an attempt to identify rapid prototyping competencies required in a rapid prototyping…

  3. The Application Trends of Rapid Prototyping Manufacturing

    Directory of Open Access Journals (Sweden)

    Qiu Xiao Lin

    2016-01-01

    characteristics of laser stero lithography (LSL selective laser sintering (SLS, three-dimensional printing (DP, fused deposition modeling (FDM, computer numerical control (CNC and other rapid prototyping technologies. After discussed these five rapid prototyping technology materials, we presented the hotspot and direction of rapid prototyping technology and look forward to the development of its technique, the expansion of its field and the progress of its academic ideology.

  4. Rapid prototyping: An innovative technique in dentistry

    Directory of Open Access Journals (Sweden)

    Shakeba Quadri

    2017-01-01

    Full Text Available Emergence of advanced digital technology has opened up new perspectives for design and production in the field of dentistry. Rapid prototyping (RP is a technique to quickly and automatically construct a three-dimensional (3D model of a part or product using 3D printers or stereolithography machines. RP has various dental applications, such as fabrication of implant surgical guides, zirconia prosthesis and molds for metal castings, maxillofacial prosthesis and frameworks for fixed and removable partial dentures, wax patterns for the dental prosthesis and complete denture. Rapid prototyping presents fascinating opportunities, but the process is difficult as it demands a high level of artistic skill, which means that the dental technicians should be able to work with the models obtained after impression to form a mirror image and achieve good esthetics. This review aims to focus on various RP methods and its application in dentistry.

  5. Implementation of Additive Rapid Prototyping on Retrofit CNC Mill

    Science.gov (United States)

    Freeform fabrication techniques are gaining popularity as a means of making parts. Layered additive methods are associated with rapid prototyping. Many rapid prototyping methods are commercially proprietary and may cost thousands of dollars. Using a retrofit CNC mill for layered fabrication and C...

  6. Flash μ-fluidics: a rapid prototyping method for fabricating microfluidic devices

    KAUST Repository

    Buttner, Ulrich

    2016-08-01

    Microfluidics has advanced in terms of design and structures; however, fabrication methods are time-consuming or expensive relative to facility costs and equipment needed. This work demonstrates a fast and economically viable 2D/3D maskless digital light-projection method based on a stereolithography process. Unlike other fabrication methods, one exposure step is used to form the whole device. Flash microfluidics is achieved by incorporating bonding and channel fabrication of complex structures in just 2.5 s to 4 s and by fabricating channel heights between 25 μm and 150 μm with photopolymer resin. The features of this fabrication technique, such as time and cost saving and easy fabrication, are used to build devices that are mostly needed in microfluidic/lab-on-chip systems. Due to the fast production method and low initial setup costs, the process could be used for point of care applications. © 2016 The Royal Society of Chemistry.

  7. Ceramic microfabrication by rapid prototyping process chains

    Indian Academy of Sciences (India)

    To avoid high tooling costs in product development, a rapid prototyping process chain has been established that enables rapid manufacturing of ceramic microcomponents from functional models to small lot series within a short time. This process chain combines the fast and inexpensive supply of master models by rapid ...

  8. Rapid Prototyping and its Application in Dentistry

    Directory of Open Access Journals (Sweden)

    V. N. V. Madhav

    2013-01-01

    Full Text Available Medical implants and biological models have three main characteristics: low volume, complex shape, and can be customized. These characteristics suit very well with Rapid Prototyping (RP and Rapid Manufacturing (RM processes. RP/RM processes are fabricated part layer- by-layer until complete shape finished from 3D model. Biocompatible materials, such as Titanium and Titanium alloy, Zirconium, Cobalt Chromium, PEEK, etc, are used for fabrication process. Reverse Engineering (RE technology greatly affects RP/RM processes. RE is used to capture or scan image of the limb, cranium, tooth, and other biological objects. Three common methods to get the image are 3D laser scanning, Computer Tomography (CT, and Magnetic Resonance Imaging (MRI. Main RP/RM techniques used in Dentistry are Stereotype Lithography Apparatus (SLA, Fused Deposition Modeling (FDM, Selective Laser Sintering (SLS, and ink jet printing. This article reviews the changing scenario of technology in dentistry with special emphasis on Rapid Prototyping and its various applications in Dentistry.

  9. Rapid prototyping of robotic platforms

    CSIR Research Space (South Africa)

    De Ronde, Willis

    2016-11-01

    Full Text Available of thickness up to 200mm can be cut to create prototype chassis/ bodies or even the final product. One of the few limitations is the cutting of certain laminated materials, as this tends to produce delaminated cutting edges or even fractures in the case... mine inspection robot (Shongololo). Shongololo’s frame is made from engineering plastics while the chassis of Dassie was made from aluminium and cut using abrasive waterjet machining. The advantage of using abrasive waterjet machining is the speed...

  10. Sheet metal forming using rapid prototyped tooling

    Science.gov (United States)

    Park, Young-Bin

    The demand for rapid, low-cost die fabrication and modification technology is greater than ever in sheet metal forming industry. One category of rapid tooling technology involves the application of advanced polymers and composites to fabricate metal forming dies. Despite their advantages in lead time and cost reductions, polymer dies for sheet metal forming applications have several drawbacks. Due to their lack of strength as compared to conventional die materials, the use of polymer dies is often limited to prototype or short-run production. In addition, because the mechanisms by which they fail are not fully understood, the dies are designed on the basis of experience and intuition. The research (1) characterized the mechanical behavior of an advanced polymer composite tooling material, (2) developed a method to predict the failure mode and the life of a polymer die, and (3) established optimal die design guidelines. The focus was on rapid prototyped, aluminum trihydrate(ATH)-filled, polyurethane-based dies in sheet metal forming. The study involved the determination of dominant process parameters based on the finite element analyses of 90° V-die bending and cylindrical cup drawing processes. The effects of process parameters on stress distribution in the die provided guidelines to the modification of die design for achieving the desired die life. The presented parametric study lays the groundwork for providing reliable tool failure prediction and design optimization guidelines for advanced polymer tooling materials in metal forming. In addition, the failure mechanisms were investigated to predict the failure mode and the fatigue life of the die. To establish a fundamental understanding of the fatigue behavior of the polyurethane-based die material, extensive material tests were performed, the microstructure was studied, and the fatigue properties were identified experimentally. The test data were incorporated into the local stress-based fatigue analysis to

  11. Solid modeling and applications rapid prototyping, CAD and CAE theory

    CERN Document Server

    Um, Dugan

    2016-01-01

    The lessons in this fundamental text equip students with the theory of Computer Assisted Design (CAD), Computer Assisted Engineering (CAE), the essentials of Rapid Prototyping, as well as practical skills needed to apply this understanding in real world design and manufacturing settings. The book includes three main areas: CAD, CAE, and Rapid Prototyping, each enriched with numerous examples and exercises. In the CAD section, Professor Um outlines the basic concept of geometric modeling, Hermite and Bezier Spline curves theory, and 3-dimensional surface theories as well as rendering theory. The CAE section explores mesh generation theory, matrix notion for FEM, the stiffness method, and truss Equations. And in Rapid Prototyping, the author illustrates stereo lithographic theory and introduces popular modern RP technologies. Solid Modeling and Applications: Rapid Prototyping, CAD and CAE Theory is ideal for university students in various engineering disciplines as well as design engineers involved in product...

  12. Rapid prototyping and stereolithography in dentistry.

    Science.gov (United States)

    Nayar, Sanjna; Bhuminathan, S; Bhat, Wasim Manzoor

    2015-04-01

    The word rapid prototyping (RP) was first used in mechanical engineering field in the early 1980s to describe the act of producing a prototype, a unique product, the first product, or a reference model. In the past, prototypes were handmade by sculpting or casting, and their fabrication demanded a long time. Any and every prototype should undergo evaluation, correction of defects, and approval before the beginning of its mass or large scale production. Prototypes may also be used for specific or restricted purposes, in which case they are usually called a preseries model. With the development of information technology, three-dimensional models can be devised and built based on virtual prototypes. Computers can now be used to create accurately detailed projects that can be assessed from different perspectives in a process known as computer aided design (CAD). To materialize virtual objects using CAD, a computer aided manufacture (CAM) process has been developed. To transform a virtual file into a real object, CAM operates using a machine connected to a computer, similar to a printer or peripheral device. In 1987, Brix and Lambrecht used, for the first time, a prototype in health care. It was a three-dimensional model manufactured using a computer numerical control device, a type of machine that was the predecessor of RP. In 1991, human anatomy models produced with a technology called stereolithography were first used in a maxillofacial surgery clinic in Viena.

  13. Rapid prototyping and stereolithography in dentistry

    Directory of Open Access Journals (Sweden)

    Sanjna Nayar

    2015-01-01

    Full Text Available The word rapid prototyping (RP was first used in mechanical engineering field in the early 1980s to describe the act of producing a prototype, a unique product, the first product, or a reference model. In the past, prototypes were handmade by sculpting or casting, and their fabrication demanded a long time. Any and every prototype should undergo evaluation, correction of defects, and approval before the beginning of its mass or large scale production. Prototypes may also be used for specific or restricted purposes, in which case they are usually called a preseries model. With the development of information technology, three-dimensional models can be devised and built based on virtual prototypes. Computers can now be used to create accurately detailed projects that can be assessed from different perspectives in a process known as computer aided design (CAD. To materialize virtual objects using CAD, a computer aided manufacture (CAM process has been developed. To transform a virtual file into a real object, CAM operates using a machine connected to a computer, similar to a printer or peripheral device. In 1987, Brix and Lambrecht used, for the first time, a prototype in health care. It was a three-dimensional model manufactured using a computer numerical control device, a type of machine that was the predecessor of RP. In 1991, human anatomy models produced with a technology called stereolithography were first used in a maxillofacial surgery clinic in Viena.

  14. Integrating Rapid Prototyping into Graphic Communications

    Science.gov (United States)

    Xu, Renmei; Flowers, Jim

    2015-01-01

    Integrating different science, technology, engineering, and mathematics (STEM) areas can help students learn and leverage both the equipment and expertise at a single school. In comparing graphic communications classes with classes that involve rapid prototyping (RP) technologies like 3D printing, there are sufficient similarities between goals,…

  15. Rapid Prototyping of wax foundry models in an incremental process

    Directory of Open Access Journals (Sweden)

    B. Kozik

    2011-04-01

    Full Text Available The paper presents an analysis incremental methods of creating wax founding models. There are two methods of Rapid Prototypingof wax models in an incremental process which are more and more often used in industrial practice and in scientific research.Applying Rapid Prototyping methods in the process of making casts allows for acceleration of work on preparing prototypes. It isespecially important in case of element having complicated shapes. The time of making a wax model depending on the size and the appliedRP method may vary from several to a few dozen hours.

  16. Review, Selection and Installation of a Rapid Prototype Machine

    Science.gov (United States)

    McEndree, Caryl

    2008-01-01

    The objective of this paper is to impress upon the reader the benefits and advantages of investing in rapid prototyping (additive manufacturing) technology thru the procurement of one or two new rapid prototyping machines and the creation of a new Prototype and Model Lab at the Kennedy Space Center (KSC). This new resource will be available to all of United Space Alliance, LLC (USA), enabling engineers from around the company to pursue a more effective means of communication and design with our co-workers, and our customer, the National Aeronautics and Space Administration (NASA). The Rapid Protoyping/3D printing industry mirrors the transition the CAD industry made several years ago, when companies were trying to justify the expenditure of converting to a 3D based system from a 2D based system. The advantages of using a 3D system seemed to be outweighed by the cost it would take to convert not only legacy 2D drawings into 3D models but the training of personnel to use the 3D CAD software. But the reality was that when a 3D CAD system is employed, it gives engineers a much greater ability to conceive new designs and the ability to engineer new tools and products much more effectively. Rapid Prototyping (RP) is the name given to a host of related technologies that are used to fabricate physical objects directly from Computer Aided Design (CAD) data sources. These methods are generally similar to each other in that they add and bond materials in a layer wise-fashion to form objects, instead of machining away material. The machines used in Rapid Prototyping are also sometimes referred to as Rapid Manufacturing machines due to the fact that some of the parts fabricated in a RP machine can be used as the finished product. The name "Rapid Prototyping" is really a misnomer. It is much more than prototypes and it is not always rapid.

  17. Removable partial dentures: use of rapid prototyping.

    Science.gov (United States)

    Lima, Julia Magalhaes Costa; Anami, Lilian Costa; Araujo, Rodrigo Maximo; Pavanelli, Carlos A

    2014-10-01

    The CAD/CAM technology associated with rapid prototyping (RP) is already widely used in the fabrication of all-ceramic fixed prostheses and in the biomedical area; however, the use of this technology for the manufacture of metal frames for removable dentures is new. This work reports the results of a literature review conducted on the use of CAD/CAM and RP in the manufacture of removable partial dentures. © 2014 by the American College of Prosthodontists.

  18. How Rapid is Rapid Prototyping? Analysis of ESPADON Programme Results

    Directory of Open Access Journals (Sweden)

    Ian D. Alston

    2003-05-01

    Full Text Available New methodologies, engineering processes, and support environments are beginning to emerge for embedded signal processing systems. The main objectives are to enable defence industry to field state-of-the-art products in less time and with lower costs, including retrofits and upgrades, based predominately on commercial off the shelf (COTS components and the model-year concept. One of the cornerstones of the new methodologies is the concept of rapid prototyping. This is the ability to rapidly and seamlessly move from functional design to the architectural design to the implementation, through automatic code generation tools, onto real-time COTS test beds. In this paper, we try to quantify the term “rapid” and provide results, the metrics, from two independent benchmarks, a radar and sonar beamforming application subset. The metrics show that the rapid prototyping process may be sixteen times faster than a conventional process.

  19. Rapid prototype modeling in a multimodality world

    Science.gov (United States)

    Bidaut, Luc; Madewell, John; Yasko, Alan

    2006-03-01

    Introduction: Rapid prototype modeling (RPM) has been used in medicine principally for bones - that are easily extracted from CT data sets - for planning orthopaedic, plastic or maxillo-facial interventions, and/or for designing custom prostheses and implants. Based on newly available technology, highly valuable multimodality approaches can now be applied to RPM, particularly for complex musculo-skeletal (MSK) tumors where multimodality often transcends CT alone. Methods: CT data sets are acquired for primary evaluation of MSK tumors in parallel with other modalities (e.g., MR, PET, SPECT). In our approach, CT is first segmented to provide bony anatomy for RPM and all other data sets are then registered to the CT reference. Parametric information relevant to the tumor's characterization is then extracted from the multimodality space and merged with the CT anatomy to produce a hybrid RPM-ready model. This model - that also accommodates digital multimodality visualization - is then produced on the latest generation of 3D printers, which permits both shapes and colors. Results: Multimodality models of complex MSK tumors have been physically produced on modern RPM equipment. This new approach has been found to be a clear improvement over the previously disconnected physical RPM and digital multimodality visualization. Conclusions: New technical developments keep opening doors to sophisticated medical applications that can directly impact the quality of patient care. Although this early work still deals with bones as base models for RPM, its use to encompass soft tissues is already envisioned for future approaches.

  20. Web tools for rapid experimental visualization prototyping

    Science.gov (United States)

    Decker, Jonathan W.; Livingstion, Mark A.

    2013-01-01

    Quite often a researcher finds themselves looking at spreadsheets of high-dimensional data generated by experimental models and user studies. We can use analysis to challenge or confirm hypothesis, but unexpected results can easily be lost in the shuffle. For this reason, it would be useful to visualize the results so we can explore our data and make new discoveries. Web browsers have become increasingly capable for creating complex, multi-view applications. Javascript is quickly becoming a de facto standard for scripting, online and offline. This work demonstrates the use of web technologies as a powerful tool for rapid visualization prototyping. We have developed two prototypes: One for high-dimensional results of the abELICIT - multi-agent version of the ELICIT platform tasked with collaborating to identify the parameters of a pending attack. Another prototype displays responses to a user study on the effectiveness of multi-layer visualization techniques. We created coordinated multiple views prototypes in the Google Chrome web browser written in Javascript, CSS and HTML. We will discuss the benefits and shortcomings of this approach.

  1. Rapid prototyping with high power fiber lasers

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, R.M. [Faculty of Sciences and Technology, New University Lisbon (Portugal); IDMEC, Instituto Superior Tecnico, TULISBON, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Lopes, G. [Welding Engineering Research Centre, Building 46, Cranfield University, Bedfordshire, MK43 0AL (United Kingdom); Quintino, L. [IDMEC, Instituto Superior Tecnico, TULISBON, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)], E-mail: lquintino@ist.utl.pt; Rodrigues, J.P. [IDMEC, Instituto Superior Tecnico, TULISBON, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Williams, S. [Welding Engineering Research Centre, Building 46, Cranfield University, Bedfordshire, MK43 0AL (United Kingdom)

    2008-12-15

    Laser rapid prototyping technologies comprise a set of technologies used in a wide range of materials to produce prototypes or small batches of complex shaped components. This paper presents a research work on rapid prototyping technology with laser additive manufacture of wire based alloy Ti-6Al-4V with an 8 kW fiber laser for the production of components with cylindrical geometry. For this, an engineering system was developed, a demonstration part produced and the deposition process was characterized. Two processing parameters were investigated: and these were the relative position between the wire feeding system and the substrate and the laser beam to wire width ratio. The former affects the molten metal transfer mode and the pressure exerted by the wire tip on the molten pool, while the laser beam to wire width ratio affects the process efficiency, since this is a compromise of process stability and process speed. Both parameters control surface finishing and the smoothness of the part. The melting efficiency of the process is low when compared to alternative processes involving powder pre deposition, but the density of the part is improved with homogeneous structural characteristics.

  2. Rapid prototyping of composite aircraft structures

    Science.gov (United States)

    Bennett, George; Rais-Rohani, Masoud; Hall, Kenneth; Holifield, Walt; Sullivan, Rani; Brown, Scott

    The faculty, staff and students of the Raspet Flight Research Laboratory (RFRL) have developed a rapid prototyping capability in a series of research aircraft and unmanned aircraft development projects. There has been a steady change in the technologies used to accomplish these tasks at the RFRL. The most recent development has been the utilization of computer graphics and a 5-axis gantry robot router to accelerate the design, moldmaking and parts trimming tasks. The composite structure fabrication processes at the RFRL have evolved from wet-lay-up to autoclave curve. Currently, the feasibility of the stitched composite material preform and resin transfer molding process is being explored.

  3. Comparison of orbital volume obtained by tomography and rapid prototyping.

    Science.gov (United States)

    Roça, Guilherme Berto; Foggiatto, José Aguiomar; Ono, Maria Cecilia Closs; Ono, Sergio Eiji; da Silva Freitas, Renato

    2013-11-01

    This study aims to compare orbital volume obtained by helical tomography and rapid prototyping. The study sample was composed of 6 helical tomography scans. Eleven healthy orbits were identified to have their volumes measured. The volumetric analysis with the helical tomography utilized the same protocol developed by the Plastic Surgery Unit of the Federal University of Paraná. From the CT images, 11 prototypes were created, and their respective volumes were analyzed in 2 ways: using software by SolidWorks and by direct analysis, when the prototype was filled with saline solution. For statistical analysis, the results of the volumes of the 11 orbits were considered independent. The average orbital volume measurements obtained by the method of Ono et al was 20.51 cm, the average obtained by the SolidWorks program was 20.64 cm, and the average measured using the prototype method was 21.81 cm. The 3 methods demonstrated a strong correlation between the measurements. The right and left orbits of each patient had similar volumes. The tomographic method for the analysis of orbital volume using the Ono protocol yielded consistent values, and by combining this method with rapid prototyping, both reliability validations of results were enhanced.

  4. Rapid Prototyping and the Human Factors Engineering Process

    Science.gov (United States)

    2016-08-29

    Rapid prototyping and the human factors • • engineering process David Beevis* and Gaetan St Denist *Senior Human Factors Engineer, Defence and...qr-..2. 9 Rapid prototyping or ’virtual prototyping ’ of human-machine interfaces offers the possibility of putting the human operator ’in the loop...8217 without the effort and cost associated with conventional man-in-the-loop simulation. Advocates suggest that rapid prototyping is compatible with

  5. Patient specific ankle-foot orthoses using rapid prototyping

    Directory of Open Access Journals (Sweden)

    Sivak Seth

    2011-01-01

    Full Text Available Abstract Background Prefabricated orthotic devices are currently designed to fit a range of patients and therefore they do not provide individualized comfort and function. Custom-fit orthoses are superior to prefabricated orthotic devices from both of the above-mentioned standpoints. However, creating a custom-fit orthosis is a laborious and time-intensive manual process performed by skilled orthotists. Besides, adjustments made to both prefabricated and custom-fit orthoses are carried out in a qualitative manner. So both comfort and function can potentially suffer considerably. A computerized technique for fabricating patient-specific orthotic devices has the potential to provide excellent comfort and allow for changes in the standard design to meet the specific needs of each patient. Methods In this paper, 3D laser scanning is combined with rapid prototyping to create patient-specific orthoses. A novel process was engineered to utilize patient-specific surface data of the patient anatomy as a digital input, manipulate the surface data to an optimal form using Computer Aided Design (CAD software, and then download the digital output from the CAD software to a rapid prototyping machine for fabrication. Results Two AFOs were rapidly prototyped to demonstrate the proposed process. Gait analysis data of a subject wearing the AFOs indicated that the rapid prototyped AFOs performed comparably to the prefabricated polypropylene design. Conclusions The rapidly prototyped orthoses fabricated in this study provided good fit of the subject's anatomy compared to a prefabricated AFO while delivering comparable function (i.e. mechanical effect on the biomechanics of gait. The rapid fabrication capability is of interest because it has potential for decreasing fabrication time and cost especially when a replacement of the orthosis is required.

  6. Rapid prototyping-assisted maxillofacial reconstruction.

    Science.gov (United States)

    Peng, Qian; Tang, Zhangui; Liu, Ousheng; Peng, Zhiwei

    2015-05-01

    Rapid prototyping (RP) technologies have found many uses in dentistry, and especially oral and maxillofacial surgery, due to its ability to promote product development while at the same time reducing cost and depositing a part of any degree of complexity theoretically. This paper provides an overview of RP technologies for maxillofacial reconstruction covering both fundamentals and applications of the technologies. Key fundamentals of RP technologies involving the history, characteristics, and principles are reviewed. A number of RP applications to the main fields of oral and maxillofacial surgery, including restoration of maxillofacial deformities and defects, reduction of functional bone tissues, correction of dento-maxillofacial deformities, and fabrication of maxillofacial prostheses, are discussed. The most remarkable challenges for development of RP-assisted maxillofacial surgery and promising solutions are also elaborated.

  7. Accuracy and precision of polyurethane dental arch models fabricated using a three-dimensional subtractive rapid prototyping method with an intraoral scanning technique.

    Science.gov (United States)

    Kim, Jae-Hong; Kim, Ki-Baek; Kim, Woong-Chul; Kim, Ji-Hwan; Kim, Hae-Young

    2014-03-01

    This study aimed to evaluate the accuracy and precision of polyurethane (PUT) dental arch models fabricated using a three-dimensional (3D) subtractive rapid prototyping (RP) method with an intraoral scanning technique by comparing linear measurements obtained from PUT models and conventional plaster models. Ten plaster models were duplicated using a selected standard master model and conventional impression, and 10 PUT models were duplicated using the 3D subtractive RP technique with an oral scanner. Six linear measurements were evaluated in terms of x, y, and z-axes using a non-contact white light scanner. Accuracy was assessed using mean differences between two measurements, and precision was examined using four quantitative methods and the Bland-Altman graphical method. Repeatability was evaluated in terms of intra-examiner variability, and reproducibility was assessed in terms of inter-examiner and inter-method variability. The mean difference between plaster models and PUT models ranged from 0.07 mm to 0.33 mm. Relative measurement errors ranged from 2.2% to 7.6% and intraclass correlation coefficients ranged from 0.93 to 0.96, when comparing plaster models and PUT models. The Bland-Altman plot showed good agreement. The accuracy and precision of PUT dental models for evaluating the performance of oral scanner and subtractive RP technology was acceptable. Because of the recent improvements in block material and computerized numeric control milling machines, the subtractive RP method may be a good choice for dental arch models.

  8. 3D Printing for the Rapid Prototyping of Structural Electronics

    National Research Council Canada - National Science Library

    Macdonald, Eric; Salas, Rudy; Espalin, David; Perez, Mireya; Aguilera, Efrain; Muse, Dan; Wicker, Ryan B

    2014-01-01

    .... The use of advanced 3D printing technology enhanced with component placement and electrical interconnect deposition can provide electronic prototypes that now can be rapidly fabricated in comparable...

  9. Rapid prototyping--when virtual meets reality.

    Science.gov (United States)

    Beguma, Zubeda; Chhedat, Pratik

    2014-01-01

    Rapid prototyping (RP) describes the customized production of solid models using 3D computer data. Over the past decade, advances in RP have continued to evolve, resulting in the development of new techniques that have been applied to the fabrication of various prostheses. RP fabrication technologies include stereolithography (SLA), fused deposition modeling (FDM), computer numerical controlled (CNC) milling, and, more recently, selective laser sintering (SLS). The applications of RP techniques for dentistry include wax pattern fabrication for dental prostheses, dental (facial) prostheses mold (shell) fabrication, and removable dental prostheses framework fabrication. In the past, a physical plastic shape of the removable partial denture (RPD) framework was produced using an RP machine, and then used as a sacrificial pattern. Yet with the advent of the selective laser melting (SLM) technique, RPD metal frameworks can be directly fabricated, thereby omitting the casting stage. This new approach can also generate the wax pattern for facial prostheses directly, thereby reducing labor-intensive laboratory procedures. Many people stand to benefit from these new RP techniques for producing various forms of dental prostheses, which in the near future could transform traditional prosthodontic practices.

  10. Rapid Prototyping as an Auxiliary in Mandibular Reconstructions.

    Science.gov (United States)

    Sales, Pedro Henrique da Hora; Cetira Filho, Edson Luiz; Oliveira Neto, Jair Queiroz de; Silva, Julianne Coelho da; Aguiar, Andrea Silvia Walter de; Mello, Manoel de Jesus Rodrigues

    2017-11-01

    The reconstruction of mandible is a challenge with regard to aesthetic and reconstructive demands. The etiology of mandibular fractures is variable, trauma, pathology, bone infections. There are many materials that provide an excellent form of rehabilitation for these defects, where the autogenous graft presents important characteristics that favor a greater success rate. Furthermore, the rapid prototyping method is quite interesting, because it brings a series of advantages to the surgeon, like reducing the operative time, among others. The purpose of the present article is to describe a clinical case of a patient with mandible bone defect caused by gunshot perforation, treated through iliac crest bone graft with planning through rapid prototyping. The mandibular reconstruction can present a real challenge for the surgeon. Biomodels should be required in complex cases because they help to decrease surgical time and to increase the predictability of the procedure.

  11. Low-cost Method for Obtaining Medical Rapid Prototyping Using Desktop 3D printing: A Novel Technique for Mandibular Reconstruction Planning.

    Science.gov (United States)

    Velasco, Ignacio; Vahdani, Soheil; Ramos, Hector

    2017-09-01

    Three-dimensional (3D) printing is relatively a new technology with clinical applications, which enable us to create rapid accurate prototype of the selected anatomic region, making it possible to plan complex surgery and pre-bend hardware for individual surgical cases. This study aimed to express our experience with the use of medical rapid prototype (MRP) of the maxillofacial region created by desktop 3D printer and its application in maxillofacial reconstructive surgeries. Three patients with benign mandible tumors were included in this study after obtaining informed consent. All patient's maxillofacial CT scan data was processed by segmentation and isolation software and mandible MRP was printed using our desktop 3D printer. These models were used for preoperative surgical planning and prebending of the reconstruction plate. MRP created by desktop 3D printer is a cost-efficient, quick and easily produced appliance for the planning of reconstructive surgery. It can contribute in patient orientation and helping them in a better understanding of their condition and proposed surgical treatment. It helps surgeons for pre-operative planning in the resection or reconstruction cases and represent an excellent tool in academic setting for residents training. The pre-bended reconstruction plate based on MRP, resulted in decreased surgery time, cost and anesthesia risks on the patients. Key words: 3D printing, medical modeling, rapid prototype, mandibular reconstruction, ameloblastoma.

  12. Rapid Tooling via Investment Casting and Rapid Prototype Patterns

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, Michael D.

    1999-06-01

    The objective of this work to develop the materials processing and design technologies required to reduce the die development time for metal mold processes from 12 months to 3 months, using die casting of Al and Mg as the example process. Sandia demonstrated that investment casting, using rapid prototype patterns produced from Stereo lithography or Selective laser Sintering, was a viable alternative/supplement to the current technology of machining form wrought stock. A demonstration die insert (ejector halt) was investment cast and subsequently tested in the die casting environment. The stationary half of the die insert was machined from wrought material to benchmark the cast half. The two inserts were run in a die casting machine for 3,100 shots of aluminum and at the end of the run no visible difference could be detected between the cast and machined inserts. Inspection concluded that the cast insert performed identically to the machined insert. Both inserts had no indications of heat checking or degradation.

  13. A Rapid Prototyping Environment for Wireless Communication Embedded Systems

    Directory of Open Access Journals (Sweden)

    Bryan A. Jones

    2003-05-01

    Full Text Available This paper introduces a rapid prototyping methodology which overcomes important barriers in the design and implementation of digital signal processing (DSP algorithms and systems on embedded hardware platforms, such as cellular phones. This paper describes rapid prototyping in terms of a simulation/prototype bridge and in terms of appropriate language design. The simulation/prototype bridge combines the strengths of simulation and of prototyping, allowing the designer to develop and evaluate next-generation communications systems, partly in simulation on a host computer and partly as a prototype on embedded hardware. Appropriate language design allows designers to express a communications system as a block diagram, in which each block represents an algorithm specified by a set of equations. Software tools developed for this paper implement both concepts, and have been successfully used in the development of a next-generation code division multiple access (CDMA cellular wireless communications system.

  14. SOT: A rapid prototype using TAE windows

    Science.gov (United States)

    Stephens, Mark; Eike, David; Harris, Elfrieda; Miller, Dana

    1986-01-01

    The development of the window interface extension feature of the Transportable Applications Executive (TAE) is discussed. This feature is being used to prototype a space station payload interface in order to demonstrate and assess the benefits of using windows on a bit mapped display and also to convey the concept of telescience, the control and operation of space station payloads from remote sites. The prototype version of the TAE with windows operates on a DEC VAXstation 100. This workstation has a high resolution 19 inch bit mapped display, a keyboard and a three-button mouse. The VAXstation 100 is not a stand-alone workstation, but is controlled by software executing on a VAX/8600. A short scenario was developed utilizing the Solar Optical Telescope (SOT) as an example payload. In the scenario the end-user station includes the VAXstation 100 plus an image analysis terminal used to display the CCD images. The layout and use of the prototype elements, i.e., the root menu, payload status window, and target acquisition menu is described.

  15. Focused ion beam lithography for rapid prototyping of metallic films

    Energy Technology Data Exchange (ETDEWEB)

    Osswald, Patrick; Kiermaier, Josef; Becherer, Markus; Schmitt-Landsiedel, Doris [Lehrstuhl fuer Technische Elektronik, TU Muenchen, Munich (Germany)

    2010-07-01

    We present FIB-lithography methods for rapid and cost-effective prototyping of metal structures covering the deep-submicron- to the millimeter-range in a single lithography cycle. Focused ion beam (FIB) systems are widely used in semiconductor industry and research facilities for both analytical testing and prototyping. A typical application is to apply electrical contact to micron-sized sensors/particles by FIB induced metal deposition. However, as for E-beam lithography, patterning times for large area bonding pads are unacceptably long, resulting in cost-intensive prototyping. In this work, we optimized FIB lithography processing for negative and positive imaging mode to form metallic structures for large-areas down do the sub-100 nm range. For negative lithography features are defined by implanting Ga{sup +}-ions into a commercial photo resist, without affecting the underlying structures by impinging ions. The structures are highly suitable for following lift-off processing due to the undercut of the resist.Metallic feature size of down to 150 nm are achievable. For positive lithography a PMMA resist is exposed in FIB irradiation. Due to the very low dose (3.10{sup 12} ions/cm{sup 2}) the writing time for an e.g. 100 {mu}m x 100 {mu}m square is approx. 15 seconds. The developed resist is used for subsequent wet chemical etching, obtaining a 100 nm resolution in metal layers.

  16. Dissipative Prototyping Methods: A Manifesto

    Science.gov (United States)

    Beesley, P.

    Taking a designer's unique perspective using examples of practice in experimental installation and digital protoyping, this manifesto acts as provocation for change and unlocking new potential by encouraging changes of perspective about the material realm. Diffusive form-language is proposed as a paradigm for architectural design. This method of design is applied through 3D printing and related digital fabrication methods, offering new qualities that can be implemented in design of realms including present earth and future interplanetary environments. A paradigm shift is encouraged by questioning conventional notions of geometry that minimize interfaces and by proposing the alternatives of maximized interfaces formed by effusive kinds of formal composition. A series of projects from the Canadian research studio of the Hylozoic Architecture group are described, providing examples of component design methods employing diffusive forms within combinations of tension-integrity structural systems integrated with hybrid metabolisms employing synthetic biology. Cultural implications are also discussed, drawing from architectural theory and natural philosophy. The conclusion of this paper suggests that the practice of diffusive prototyping can offer formative strategies contributing to design of future living systems.

  17. Bio rapid prototyping by extruding/aspirating/refilling thermoreversible hydrogel

    Energy Technology Data Exchange (ETDEWEB)

    Iwami, K; Noda, T; Ishida, K; Umeda, N [Department of Mechanical Systems and Engineering, Tokyo University of Agriculture and Technology, 2-24-16 Nakacho, Koganei, Tokyo 184-8588 (Japan); Morishima, K [Department of Bio-Applications and Systems Engineering, Tokyo University of Agriculture and Technology, 2-24-16 Nakacho, Koganei, Tokyo 184-8588 (Japan); Nakamura, M, E-mail: k_iwami@cc.tuat.ac.j [Department of Life Sciences and Bioengineering, University of Toyama, 3190 Gofuku, Toyama, 930-8555 (Japan)

    2010-03-15

    This paper reports a method for rapid prototyping of cell tissues, which is based on a system that extrudes, aspirates and refills a mixture of cells and thermoreversible hydrogel as a scaffold. In the extruding mode, a cell-mixed scaffold solution in the sol state is extruded from a cooled micronozzle into a temperature-controlled substrate, which keeps the scaffold in the gel state. In the aspiration mode, the opposite process is performed by Bernoulli suction. In the refilling mode, the solution is extruded into a groove created in the aspiration mode. The minimum width of extruded hydrogel pattern is 114 +- 15 mum by employing a nozzle of diameter 100 mum, and that of aspirated groove was 355 +- 10 mum using a 500 mum-diameter nozzle. Gum arabic is mixed with the scaffold solution to avoid peeling-off of the gel pattern from the substrate. Patterning of Sf-9 cell tissue is demonstrated, and the stability of the patterned cell is investigated. This system offers a procedure for rapid prototyping and local modification of cell scaffolds for tissue engineering.

  18. Rapid, Reliable Shape Setting of Superelastic Nitinol for Prototyping Robots.

    Science.gov (United States)

    Gilbert, Hunter B; Webster, Robert J

    Shape setting Nitinol tubes and wires in a typical laboratory setting for use in superelastic robots is challenging. Obtaining samples that remain superelastic and exhibit desired precurvatures currently requires many iterations, which is time consuming and consumes a substantial amount of Nitinol. To provide a more accurate and reliable method of shape setting, in this paper we propose an electrical technique that uses Joule heating to attain the necessary shape setting temperatures. The resulting high power heating prevents unintended aging of the material and yields consistent and accurate results for the rapid creation of prototypes. We present a complete algorithm and system together with an experimental analysis of temperature regulation. We experimentally validate the approach on Nitinol tubes that are shape set into planar curves. We also demonstrate the feasibility of creating general space curves by shape setting a helical tube. The system demonstrates a mean absolute temperature error of 10°C.

  19. A review of rapid prototyping techniques for tissue engineering purposes

    NARCIS (Netherlands)

    Peltola, Sanna M.; Melchels, Ferry P. W.; Grijpma, Dirk W.; Kellomaki, Minna

    2008-01-01

    Rapid prototyping (RP) is a common name for several techniques, which read in data from computer-aided design (CAD) drawings and manufacture automatically three-dimensional objects layer-by-layer according to the virtual design. The utilization of RP in tissue engineering enables the production of

  20. Rapid Prototyping of Electrically Small Spherical Wire Antennas

    DEFF Research Database (Denmark)

    Kim, Oleksiy S.

    2014-01-01

    It is shown how modern rapid prototyping technologies can be applied for quick and inexpensive, but still accurate, fabrication of electrically small wire antennas. A well known folded spherical helix antenna and a novel spherical zigzag antenna have been fabricated and tested, exhibiting the imp...

  1. Rapid Prototyping of Tangibles with a Capacitive Mouse

    DEFF Research Database (Denmark)

    Ramos, Juan David Hincapie; Esbensen, Morten; Kogutowska, Magdalena

    2011-01-01

    lays the capacitive surface and communication capa- bilities of a Microsoft TouchMouse, both of which are ap- propriated to fulfill the mentined requirements. Unlike ex- isting approaches for rapid prototyping of tangibles like the Arduino boards, using the Toki toolkit does not require de- velopers...

  2. Pediatric Dispersible Tablets: a Modular Approach for Rapid Prototyping.

    Science.gov (United States)

    Buck, Jonas; Huwyler, Jörg; Kühl, Peter; Dischinger, Angela

    2016-08-01

    The design of pediatric formulations is challenging. Solid dosage forms for children have to meet the needs of different ages, e.g. high number of dosing increments and strengths. A modular formulation strategy offering the possibility of rapid prototyping was applied. Different tablet compositions and the resulting tablet characteristics were investigated for dispersible tablets using customized analytical methods. Fluid bed granules were blended with extragranular components, and compressed to tablets. Disintegration behavior was studied with a Texture Analyzer and a Tensiometer. Methods for determination of disintegration time and water uptake of tablets were developed with a Texture Analyzer, and a Tensiometer, respectively. Twenty-two different tablet formulations were prepared and analyzed with respect to disintegration time, hardness, friability, and viscosity. Multivariate data analysis revealed a high impact of type and amount of viscosity enhancer on the disintegration behavior of tablets. An optimized formulation was selected with a disintegration time of 24 s. Methods providing additional information on the disintegration behavior of dispersible tablets compared to standard pharmacopoeia methods were established. Selecting the right type and level of viscosity enhancer and superdisintegrant was critical for developing pediatric tablets with a disintegration time of less than 30 s but still pleasant mouth feel.

  3. Dimensional Precision Research of Wax Molding Rapid Prototyping based on Droplet Injection

    Science.gov (United States)

    Mingji, Huang; Geng, Wu; yan, Shan

    2017-11-01

    The traditional casting process is complex, the mold is essential products, mold quality directly affect the quality of the product. With the method of rapid prototyping 3D printing to produce mold prototype. The utility wax model has the advantages of high speed, low cost and complex structure. Using the orthogonal experiment as the main method, analysis each factors of size precision. The purpose is to obtain the optimal process parameters, to improve the dimensional accuracy of production based on droplet injection molding.

  4. Rapid Prototyping Integrated With Nondestructive Evaluation and Finite Element Analysis

    Science.gov (United States)

    Abdul-Aziz, Ali; Baaklini, George Y.

    2001-01-01

    Most reverse engineering approaches involve imaging or digitizing an object then creating a computerized reconstruction that can be integrated, in three dimensions, into a particular design environment. Rapid prototyping (RP) refers to the practical ability to build high-quality physical prototypes directly from computer aided design (CAD) files. Using rapid prototyping, full-scale models or patterns can be built using a variety of materials in a fraction of the time required by more traditional prototyping techniques (refs. 1 and 2). Many software packages have been developed and are being designed to tackle the reverse engineering and rapid prototyping issues just mentioned. For example, image processing and three-dimensional reconstruction visualization software such as Velocity2 (ref. 3) are being used to carry out the construction process of three-dimensional volume models and the subsequent generation of a stereolithography file that is suitable for CAD applications. Producing three-dimensional models of objects from computed tomography (CT) scans is becoming a valuable nondestructive evaluation methodology (ref. 4). Real components can be rendered and subjected to temperature and stress tests using structural engineering software codes. For this to be achieved, accurate high-resolution images have to be obtained via CT scans and then processed, converted into a traditional file format, and translated into finite element models. Prototyping a three-dimensional volume of a composite structure by reading in a series of two-dimensional images generated via CT and by using and integrating commercial software (e.g. Velocity2, MSC/PATRAN (ref. 5), and Hypermesh (ref. 6)) is being applied successfully at the NASA Glenn Research Center. The building process from structural modeling to the analysis level is outlined in reference 7. Subsequently, a stress analysis of a composite cooling panel under combined thermomechanical loading conditions was performed to validate

  5. Rapid control prototyping for cylinder pressure indication; Rapid Control Prototyping fuer Zylinderdruckindizierung

    Energy Technology Data Exchange (ETDEWEB)

    Pfluger, Jan [RWTH Aachen Univ. (Germany). Lehrstuhl fuer Verbrennungskraftmaschinen; Andert, Jakob [FEV GmbH, Aachen (Germany). Fahrzeugelektronik/E-Mobilitaet; Ross, Holger; Mertens, Frank [dSpace GmbH, Paderborn (Germany). Rapid Control Prototyping Systems

    2012-11-15

    Cylinder-pressure-based controls that allow cycle-synchronous reactions to events in the combustion chamber are a particularly promising possibility further optimising engine combustion processes. However, the requirements of real-time cylinder indication are fast pushing today's systems up against their limits. The Institute for Combustion Engines at RWTH Aachen University and dSpace together developed a high performance prototype for online indication with cycle-synchronous combustion control. (orig.)

  6. Rapid prototyping of replica knee implants for in vitro testing

    Directory of Open Access Journals (Sweden)

    Verjans Mark

    2016-09-01

    Full Text Available The understanding of the complex biomechanics of the knee is a key for an optimal implant design. To easily investigate the influence of prosthetic designs on knee biomechanics a rapid prototyping workflow for knee implants has been developed and evaluated. Therefore, different manufacturing technologies and post-treatment methods have been examined and overall seven different replica knee implants were manufactured. For evaluation, the manufacturing properties such as surface accuracy and roughness were determined and kinematic behaviour was investigated in a novel knee testing rig. It was carried out that PolyJet-Modelling with a sanded surface resulted in changed kinematic patterns compared to a usual CoCr-UHMWPE implant. However, fused deposition modelling using ABS and subsequent surface smoothening with acetone vapor showed the lowest roughness of the manufactured implants and only minor kinematic differences. For this reason this method constitutes a promising approach towards an optimal implant design for improved patient-satisfaction and long lifetime of the implant. Finally the workflow is not only limited to the knee.

  7. Machine accuracy for rapid prototyping of quality components

    Science.gov (United States)

    Gu, Peihua; Yan, May; Huang, X.; Zhang, Xiaochen

    1998-10-01

    Ever-growing global competition forces manufacturers to deliver more competitive products with better quality, lower price and in short time. One of the most important and challenging tasks faced by value-added product manufacturing industry is substantial reduction of product development time. Rapid prototyping technologies have received significant interests from both research and industrial communities. Due to the model accuracy, integrity and strength problems, their applications are limited. The most common sources of errors in the rapid prototyping and manufacturing systems including Cubital machines can be categorized as mathematical, process-related or material- related errors. In this paper, we present an analysis of accuracy of a Cubital Solider 4600 machine and an application on pattern and mould design and manufacturing. The experimental study determines the relationships between the machine accuracy and dimensions and parameter setting, which can be used to control the accuracy of parts to be built.

  8. Rapid prototyping technology and its application in bone tissue engineering.

    Science.gov (United States)

    Yuan, Bo; Zhou, Sheng-Yuan; Chen, Xiong-Sheng

    Bone defects arising from a variety of reasons cannot be treated effectively without bone tissue reconstruction. Autografts and allografts have been used in clinical application for some time, but they have disadvantages. With the inherent drawback in the precision and reproducibility of conventional scaffold fabrication techniques, the results of bone surgery may not be ideal. This is despite the introduction of bone tissue engineering which provides a powerful approach for bone repair. Rapid prototyping technologies have emerged as an alternative and have been widely used in bone tissue engineering, enhancing bone tissue regeneration in terms of mechanical strength, pore geometry, and bioactive factors, and overcoming some of the disadvantages of conventional technologies. This review focuses on the basic principles and characteristics of various fabrication technologies, such as stereolithography, selective laser sintering, and fused deposition modeling, and reviews the application of rapid prototyping techniques to scaffolds for bone tissue engineering. In the near future, the use of scaffolds for bone tissue engineering prepared by rapid prototyping technology might be an effective therapeutic strategy for bone defects.

  9. Improved rapid prototyping methodology for MPEG-4 IC development

    Science.gov (United States)

    Tang, Clive K. K.; Moseler, Kathy; Levi, Sami

    1998-12-01

    One important factor in deciding the success of a new consumer product or integrated circuit is minimized time-to- market. A rapid prototyping methodology that encompasses algorithm development in the hardware design phase will have great impact on reducing time-to-market. In this paper, a proven hardware design methodology and a novel top-down design methodology based on Frontier Design's DSP Station tool are described. The proven methodology was used during development of the MC149570 H.261/H.263 video codec manufactured by Motorola. This paper discusses an improvement to this method to create an integrated environment for both system and hardware development, thereby further reducing the time-to-market. The software tool chosen is DSP Station tool by Frontier Design. The rich features of DSP Station tool will be described and then it will be shown how these features may be useful in designing from algorithm to silicon. How this methodology may be used in the development of a new MPEG4 Video Communication ASIC will be outlined. A brief comparison with a popular tool, Signal Processing WorkSystem tool by Cadence, will also be given.

  10. Towards rapid prototyped convective microfluidic DNA amplification platform

    Science.gov (United States)

    Ajit, Smrithi; Praveen, Hemanth Mithun; Puneeth, S. B.; Dave, Abhishek; Sesham, Bharat; Mohan, K. N.; Goel, Sanket

    2017-02-01

    Today, Polymerase Chain Reaction (PCR) based DNA amplification plays an indispensable role in the field of biomedical research. Its inherent ability to exponentially amplify sample DNA has proven useful for the identification of virulent pathogens like those causing Multiple Drug-Resistant Tuberculosis (MDR-TB). The intervention of Microfluidics technology has revolutionized the concept of PCR from being a laborious and time consuming process into one that is faster, easily portable and capable of being multifunctional. The Microfluidics based PCR outweighs its traditional counterpart in terms of flexibility of varying reaction rate, operation simplicity, need of a fraction of volume and capability of being integrated with other functional elements. The scope of the present work involves the development of a real-time continuous flow microfluidic device, fabricated by 3D printing-governed rapid prototyping method, eventually leading to an automated and robust platform to process multiple DNA samples for detection of MDRTB-associated mutations. The thermal gradient characteristic to the PCR process is produced using peltier units appropriate to the microfluidic environment fully monitored and controlled by a low cost controller driven by a Data Acquisition System. The process efficiency achieved in the microfluidic environment in terms of output per cycle is expected to be on par with the traditional PCR and capable of earning the additional advantages of being faster and minimizing the handling.

  11. Rapid prototyping of biomimetic vascular phantoms for hyperspectral reflectance imaging.

    Science.gov (United States)

    Ghassemi, Pejhman; Wang, Jianting; Melchiorri, Anthony J; Ramella-Roman, Jessica C; Mathews, Scott A; Coburn, James C; Sorg, Brian S; Chen, Yu; Pfefer, T Joshua

    2015-01-01

    The emerging technique of rapid prototyping with three-dimensional (3-D) printers provides a simple yet revolutionary method for fabricating objects with arbitrary geometry. The use of 3-D printing for generating morphologically biomimetic tissue phantoms based on medical images represents a potentially major advance over existing phantom approaches. Toward the goal of image-defined phantoms, we converted a segmented fundus image of the human retina into a matrix format and edited it to achieve a geometry suitable for printing. Phantoms with vessel-simulating channels were then printed using a photoreactive resin providing biologically relevant turbidity, as determined by spectrophotometry. The morphology of printed vessels was validated by x-ray microcomputed tomography. Channels were filled with hemoglobin (Hb) solutions undergoing desaturation, and phantoms were imaged with a near-infrared hyperspectral reflectance imaging system. Additionally, a phantom was printed incorporating two disjoint vascular networks at different depths, each filled with Hb solutions at different saturation levels. Light propagation effects noted during these measurements—including the influence of vessel density and depth on Hb concentration and saturation estimates, and the effect of wavelength on vessel visualization depth—were evaluated. Overall, our findings indicated that 3-D-printed biomimetic phantoms hold significant potential as realistic and practical tools for elucidating light–tissue interactions and characterizing biophotonic system performance.

  12. NASA Applied Sciences Program Rapid Prototyping Results and Conclusions

    Science.gov (United States)

    Cox, E. L.

    2007-12-01

    NASA's Applied Sciences Program seeks to expand the use of Earth science research results to benefit current and future operational systems tasked with making policy and management decisions. The Earth Science Division within the Science Mission Directorate sponsors over 1000 research projects annually to answer the fundamental research question: How is the Earth changing and what are the consequences for life on Earth? As research results become available, largely from satellite observations and Earth system model outputs, the Applied Sciences Program works diligently with scientists and researchers (internal and external to NASA) , and other government agency officials (USDA, EPA, CDC, DOE, US Forest Service, US Fish and Wildlife Service, DHS, USAID) to determine useful applications for these results in decision-making, ultimately benefiting society. The complexity of Earth science research results and the breadth of the Applied Sciences Program national priority areas dictate a broad scope and multiple approaches available to implement their use in decision-making. Over the past five years, the Applied Sciences Program has examined scientific and engineering practices and solicited the community for methods and steps that can lead to the enhancement of operational systems (Decision Support Systems - DSS) required for decision-making. In November 2006, the Applied Sciences Program launched an initiative aimed at demonstrating the applicability of NASA data (satellite observations, models, geophysical parameters from data archive centers) being incorporated into decision support systems and their related environments at a low cost and quick turnaround of results., i.e. designed rapid prototyping. Conceptually, an understanding of Earth science research (and results) coupled with decision-making requirements and needs leads to a demonstration (experiment) depicting enhancements or improvements to an operational decisions process through the use of NASA data. Five

  13. Friction Induced Wear of Rapid Prototyping Generated Materials: A Review

    Directory of Open Access Journals (Sweden)

    A. Tsouknidas

    2011-01-01

    Full Text Available Additive manufacturing has been introduced in the early 80s and has gained importance as a manufacturing process ever since. Even though the inception of the implicated processes predominantly focused on prototyping purposes, during the last years rapid prototyping (RP has emerged as a key enabling technology for the fabrication of highly customized, functionally gradient materials. This paper reviews friction-related wear phenomena and the corresponding deterioration mechanisms of RP-generated components as well as the potential of improving the implicated materials' wear resistance without significantly altering the process itself. The paper briefly introduces the concept of RP technologies and the implicated materials, as a premises to the process-dependent wear progression of the generated components for various degeneration scenarios (dry sliding, fretting, etc..

  14. Rapid Control Prototyping Plataform for Didactic Plant Motor DC

    Directory of Open Access Journals (Sweden)

    Cristian Bazán-Orobio

    2013-06-01

    Full Text Available In this paper a design, implementation and validation of a Rapid Control Prototype platform for a plant based on a DC motor is proposed. This low-cost prototype provides of an electronic card (with a motor DC and sensors manipulated by PC with free software tools using Linux, Scilab / Scicos and RTAI-Lab. This RCP System allows developing speed -position control trainings by using different types of PID industrial controllers with anti – wind up and bump less transfer schemes. We develop a speed control application structured in four steps: identification, controller design, simulation and real time control, where there are pedagogical advantages of a platform that not only allows simulation but also real-time control of a plant.

  15. Reverse Design and Rapid Prototyping ABS Part Assembly with Hard Material

    Directory of Open Access Journals (Sweden)

    Xu Yaodong

    2016-01-01

    Full Text Available In order to realize the variant design of the existing product , and rapid completion of the manufacturing and assembly, a new product was designed by reverse design method,and manufactured by rapid prototyping technology to finish assembly with hard material part. An experiment of rapid prototyping part with different model scales assembling with metal part was done to find the right scale of 1.008 of the model in H/h tolerance fit and 0.1mm more in size in interference fit. Through the static theory analysis, the amount of the interference fit was calculated by equal torque in contrast with mechanical assembly.The result was further proved by ProE mechanica simulation for stress and strain. Applying the rule of the results in experiment,prototyping part assembly with hard material part in different types of fit can be realized.

  16. [Effects and influential factors of rapid prototyping technology in dental restorations].

    Science.gov (United States)

    Pan, Qiao-Ling; Yuan, Jia-Kan

    2017-06-01

    To explore the effects and influential factors of rapid prototyping technology in dental restorations. From May 2013 to November 2014 in our hospital, 120 patients were divided into experimental group and conventional group. Patients in the experimental group were treated by rapid prototyping technology, while patients in the conventional group were treated by routine methods. The effects of the two groups were compared using SPSS 17.0 software package. The effective rate of the experimental group was significantly higher than that of the conventional group (P<0.05). Complications in the experimental group were significantly lower than those in the conventional group (P<0.05). Rapid prototyping technology can be used in the treatment of patients with dentition defects with satisfactory results and fewer adverse reactions.

  17. The Requirements and Design of the Rapid Prototyping Capabilities System

    Science.gov (United States)

    Haupt, T. A.; Moorhead, R.; O'Hara, C.; Anantharaj, V.

    2006-12-01

    The Rapid Prototyping Capabilities (RPC) system will provide the capability to rapidly evaluate innovative methods of linking science observations. To this end, the RPC will provide the capability to integrate the software components and tools needed to evaluate the use of a wide variety of current and future NASA sensors, numerical models, and research results, model outputs, and knowledge, collectively referred to as "resources". It is assumed that the resources are geographically distributed, and thus RPC will provide the support for the location transparency of the resources. The RPC system requires providing support for: (1) discovery, semantic understanding, secure access and transport mechanisms for data products available from the known data provides; (2) data assimilation and geo- processing tools for all data transformations needed to match given data products to the model input requirements; (3) model management including catalogs of models and model metadata, and mechanisms for creation environments for model execution; and (4) tools for model output analysis and model benchmarking. The challenge involves developing a cyberinfrastructure for a coordinated aggregate of software, hardware and other technologies, necessary to facilitate RPC experiments, as well as human expertise to provide an integrated, "end-to-end" platform to support the RPC objectives. Such aggregation is to be achieved through a horizontal integration of loosely coupled services. The cyberinfrastructure comprises several software layers. At the bottom, the Grid fabric encompasses network protocols, optical networks, computational resources, storage devices, and sensors. At the top, applications use workload managers to coordinate their access to physical resources. Applications are not tightly bounded to a single physical resource. Instead, they bind dynamically to resources (i.e., they are provisioned) via a common grid infrastructure layer. For the RPC system, the

  18. TOPPE: A framework for rapid prototyping of MR pulse sequences.

    Science.gov (United States)

    Nielsen, Jon-Fredrik; Noll, Douglas C

    2017-11-02

    To introduce a framework for rapid prototyping of MR pulse sequences. We propose a simple file format, called "TOPPE", for specifying all details of an MR imaging experiment, such as gradient and radiofrequency waveforms and the complete scan loop. In addition, we provide a TOPPE file "interpreter" for GE scanners, which is a binary executable that loads TOPPE files and executes the sequence on the scanner. We also provide MATLAB scripts for reading and writing TOPPE files and previewing the sequence prior to hardware execution. With this setup, the task of the pulse sequence programmer is reduced to creating TOPPE files, eliminating the need for hardware-specific programming. No sequence-specific compilation is necessary; the interpreter only needs to be compiled once (for every scanner software upgrade). We demonstrate TOPPE in three different applications: k-space mapping, non-Cartesian PRESTO whole-brain dynamic imaging, and myelin mapping in the brain using inhomogeneous magnetization transfer. We successfully implemented and executed the three example sequences. By simply changing the various TOPPE sequence files, a single binary executable (interpreter) was used to execute several different sequences. The TOPPE file format is a complete specification of an MR imaging experiment, based on arbitrary sequences of a (typically small) number of unique modules. Along with the GE interpreter, TOPPE comprises a modular and flexible platform for rapid prototyping of new pulse sequences. Magn Reson Med, 2017. © 2017 International Society for Magnetic Resonance in Medicine. © 2017 International Society for Magnetic Resonance in Medicine.

  19. A Rapid Prototyping Technique for Microfluidics with High Robustness and Flexibility

    Directory of Open Access Journals (Sweden)

    Zhenhua Liu

    2016-11-01

    Full Text Available In microfluidic device prototyping, master fabrication by traditional photolithography is expensive and time-consuming, especially when the design requires being repeatedly modified to achieve a satisfactory performance. By introducing a high-performance/cost-ratio laser to the traditional soft lithography, this paper describes a flexible and rapid prototyping technique for microfluidics. An ultraviolet (UV laser directly writes on the photoresist without a photomask, which is suitable for master fabrication. By eliminating the constraints of fixed patterns in the traditional photomask when the masters are made, this prototyping technique gives designers/researchers the convenience to revise or modify their designs iteratively. A device fabricated by this method is tested for particle separation and demonstrates good properties. This technique provides a flexible and rapid solution to fabricating microfluidic devices for non-professionals at relatively low cost.

  20. Rapid prototyping tool for tuning of vibration absorbers; Rapid-Prototyping-Tool zur Abstimmung von Schwingungstilgern

    Energy Technology Data Exchange (ETDEWEB)

    Marienfeld, P.M.; Karkosch, H.J. [ContiTech Vibration Control GmbH, Hannover (Germany); Bohn, C. [Technische Univ. Clausthal (Germany); Svaricek, F. [Univ. der Bundeswehr Muenchen (Germany); Knake-Langhorst, S. [Deutsches Zentrum fuer Luft- und Raumfahrt, Braunschweig (Germany)

    2008-07-01

    In the automotive industry passive vibration absorbers are a well established method to reduce structural vibrations in automotive vehicles. Designing a vibration absorber consists of selecting its mechanical properties. Usually extensive tests are necessary with different absorbers in the vehicle and subjective as well as objective evaluation of the results. This requires hardware modifications between different tests. In this paper, an approach is proposed that can assist in the development of vibration absorbers. It is based on tuning an active vibration control system such that it reproduces the behavior of a specified vibration absorber. This behavior can then be changed electronically without modifying the hardware. Two different control approaches are compared. In the first approach, the apparent physical properties of a vibration absorber are directly modified through acceleration, velocity or displacement feedback. In the second approach, a desired dynamic mass transfer function for the vibration absorber is prescribed and an H2-norm optimal model matching problem is solved. Experimental results obtained with this approach are presented. (orig.)

  1. Prototyping

    OpenAIRE

    Corsín Jiménez, Alberto

    2017-01-01

    The prototyping of method calls for, at a minimum, three operations of design: rethinking the proprietary and legal economy of research; rethinking the frontiers that separate those who use methods from those to whom methods are applied to; designing infrastructures of apprenticeships for every problem.

  2. Rapid laser prototyping of valves for microfluidic autonomous systems

    Science.gov (United States)

    Mohammed, M. I.; Abraham, E.; Y Desmulliez, M. P.

    2013-03-01

    Capillary forces in microfluidics provide a simple yet elegant means to direct liquids through flow channel networks. The ability to manipulate the flow in a truly automated manner has proven more problematic. The majority of valves require some form of flow control devices, which are manually, mechanically or electrically driven. Most demonstrated capillary systems have been manufactured by photolithography, which, despite its high precision and repeatability, can be labour intensive, requires a clean room environment and the use of fixed photomasks, limiting thereby the agility of the manufacturing process to readily examine alternative designs. In this paper, we describe a robust and rapid CO2 laser manufacturing process and demonstrate a range of capillary-driven microfluidic valve structures embedded within a microfluidic network. The manufacturing process described allows for advanced control and manipulation of fluids such that flow can be halted, triggered and delayed based on simple geometrical alterations to a given microchannel. The rapid prototyping methodology has been employed with PMMA substrates and a complete device has been created, ready for use, within 2-3 h. We believe that this agile manufacturing process can be applied to produce a range of complex autonomous fluidic platforms and allows subsequent designs to be rapidly explored.

  3. Epitrochoid Power-Law Nozzle Rapid Prototype Build/Test Project (Briefing Charts)

    Science.gov (United States)

    2015-02-01

    Power-Law Nozzle Rapid Prototype Build/Test Project Mr. Eric J. Paulson-Vehicle Analyst Rocket Propulsion Division Combustion devices Branch Systems...to build axisymmetric cold flow nozzle test articles using plastic-based inexpensive rapid additive manufacturing – Feasible to rapid prototype lobed...Briefing Charts 3. DATES COVERED (From - To) February 2015-March 2015 4. TITLE AND SUBTITLE Epitrochoid Power-Law Nozzle Rapid Prototype Build/Test

  4. Femur Model Reconstruction Based on Reverse Engineering and Rapid Prototyping

    Science.gov (United States)

    Tang, Tongming; Zhang, Zheng; Ni, Hongjun; Deng, Jiawen; Huang, Mingyu

    Precise reconstruction of 3D models is fundamental and crucial to the researches of human femur. In this paper we present our approach towards tackling this problem. The surface of a human femur was scanned using a hand-held 3D laser scanner. The data obtained, in the form of point cloud, was then processed using the reverse engineering software Geomagic and the CAD/CAM software CimatronE to reconstruct a digital 3D model. The digital model was then used by the rapid prototyping machine to build a physical model of human femur using 3D printing. The geometric characteristics of the obtained physical model matched that of the original femur. The process of "physical object - 3D data - digital 3D model - physical model" presented in this paper provides a foundation of precise modeling for the digital manufacturing, virtual assembly, stress analysis, and simulated surgery of artificial bionic femurs.

  5. TOPAZ II Anti-Criticality Device Rapid Prototype

    Science.gov (United States)

    Campbell, Donald R.; Otting, William D.

    1994-07-01

    The Ballistic Missile Defense Organization (BMDO) has been working on a Nuclear Electric Propulsion Space Test Project (NEPSTP) using an existing Russian Topaz II reactor system to power the NEPSTP satellite. Safety investigations have shown that it will be possible to safely launch the Topaz II system in the United States with some modification to preclude water flooded criticality. A ``fuel-out'' water subcriticality concept was selected by the Los Alamos National Laboratory (LANL) as the baseline concept. A fuel-out anti-criticality device (ACD) conceptual design was developed by Rockwell. The concept functions to hold the fuel from the four centermost thermionic fuel elements (TFEs) outside the reactor during launch and reliably inserts the fuel into the reactor once the operational orbit is achieved. A four-tenths scale ACD rapid prototype model, fabricated from the CATIA solids design model, clearly shows in three dimensions the relative size and spatial relationship of the ACD components.

  6. Compact form fitting small antennas using three-dimensional rapid prototyping

    Science.gov (United States)

    Willis, Bryan Jon

    Three-dimensional (3D) rapid prototyping holds significant promise for future antenna designs. Many complex designs that would be unmanufacturable or costly are realizable on a 3D printing machine. The ability to create 3D designs of virtually any configuration makes it possible to build compact antennas that can form fit to any space. These antennas build on the concept that small antennas can best reach the ideal operating limit when utilizing the entire 3D space in a sphere surrounding the antenna. Antennas require a combination of dielectric and conductive materials. 3D rapid prototyping is already well advanced for plastics and dielectric materials (with more options coming online). Prototyping with conductive materials has lagged behind; due mainly to their higher melting points, but this is advancing as well. This dissertation focuses on 3D rapid prototyping for antenna design. A 3D antenna made from small cubical cells is optimized for 2.4--3GHz using a genetic algorithm (GA). The antennas are built using 3D printing of plastic covered by conductive paint. The effects of the conductivity of the paint and number of layers on the resonance and gain of the antenna are evaluated. These results demonstrate the feasibility of using 3D rapid prototyping for antenna design. A 3D dipole is also optimized using a GA to function from 510--910MHz. The antenna was built using 3D rapid prototyping from plastic. The 3D antenna was covered with a conductive coating and measured, showing good agreement with simulation. The 3D GA is used to design 3D antennas of random shape to fit inside the empty space in a cell phone case and optimized for cell phone bands 800--900MHz and 1.6--3.7GHz. The research also evaluates methods and materials that can be used to produce 3D antennas. In addition to the flexibility that 3D prototyping brings to antenna design, this paper describes how this new and emerging method for building antennas can provide fast and affordable antennas for

  7. Rapid Prototyping of Continuous Fiber Reinforced Ceramic Matrix Composites

    Science.gov (United States)

    Vaidyanathan, R.; Green, C.; Phillips, T.; Cipriani, R.; Yarlagadda, S.; Gillespie, J. W., Jr.; Effinger, M.; Cooper, K. C.

    2003-01-01

    For ceramics to be used as structural components in high temperature applications, their fracture toughness is improved by embedding continuous ceramic fibers. Ceramic matrix composite (CMC) materials allow increasing the overall operating temperature, raising the temperature safety margins, avoiding the need for cooling, and improving the damping capacity, while reducing the weight at the same time. They also need to be reliable and available in large quantities as well. In this paper, an innovative rapid prototyping technique to fabricate continuous fiber reinforced ceramic matrix composites is described. The process is simple, robust and will be widely applicable to a number of high temperature material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The results of mechanical properties and microstructural characterization are presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts at an order of magnitude lower cost than current chemical vapor infiltration (CVI) and polymer impregnation and pyrolysis (PIP) processes.

  8. Print your own membrane: direct rapid prototyping of polydimethylsiloxane.

    Science.gov (United States)

    Femmer, Tim; Kuehne, Alexander J C; Wessling, Matthias

    2014-08-07

    Polydimethylsiloxane is a translucent and biologically inert silicone material used in sealants, biomedical implants and microscale lab-on-a-chip devices. Furthermore, in membrane technology, polydimethylsiloxane represents a material for separation barriers as it has high permeabilities for various gases. The facile handling of two component formulations with a silicone base material, a catalyst and a small molecular weight crosslinker makes it widely applicable for soft-lithographic replication of two-dimensional device geometries, such as microfluidic chips or micro-contact stamps. Here, we develop a new technique to directly print polydimethylsiloxane in a rapid prototyping device, circumventing the need for masks or sacrificial mold production. We create a three-dimensional polydimethylsiloxane membrane for gas-liquid-contacting based on a Schwarz-P triple-periodic minimal-surface, which is inaccessible with common machining techniques. Direct 3D-printing of polydimethylsiloxane enables rapid production of novel chip geometries for a manifold of lab-on-a-chip applications.

  9. Rapid Prototyping of Field Programmable Gate Array-Based Discrete Cosine Transform Approximations

    Directory of Open Access Journals (Sweden)

    Trevor W. Fox

    2003-05-01

    Full Text Available A method for the rapid design of field programmable gate array (FPGA-based discrete cosine transform (DCT approximations is presented that can be used to control the coding gain, mean square error (MSE, quantization noise, hardware cost, and power consumption by optimizing the coefficient values and datapath wordlengths. Previous DCT design methods can only control the quality of the DCT approximation and estimates of the hardware cost by optimizing the coefficient values. It is shown that it is possible to rapidly prototype FPGA-based DCT approximations with near optimal coding gains that satisfy the MSE, hardware cost, quantization noise, and power consumption specifications.

  10. Studying the Technology of Creating Cortical Electrode Instruments using the Rapid Prototyping Technology

    Directory of Open Access Journals (Sweden)

    Ablyaz T. R.

    2017-06-01

    Full Text Available This paper shows the results of studying the technology of manufacturing cortical electrode-instruments (EI with the use of indirect methods of the Rapid Prototyping technology. Functional EI prototypes were made by layered synthesis of the photopolymer material with the use of the stereolithography technology (SLA - Stereo Lithography Apparatus. The article is focused on two methods of indirect EI manufacturing. One of the EI prototypes was used for making a molded wax model for hot investment casting, followed by applying copper coating. The second prototype was used for applying copper plating to a prepared current-conductive layer. As a result of EDMing a steel workpiece, both EIs reached the desired depth, which is 1 mm. The copper plating applied to the EI preserves its integrity. Through the use of the casting technology, there is a possibility to cut the economic costs by 35%. Using a prototype with preliminarily applied conductive coating makes it possible to make geometrically-complex EIs.

  11. Digital image capture and rapid prototyping of the maxillofacial defect.

    Science.gov (United States)

    Sabol, Jennifer V; Grant, Gerald T; Liacouras, Peter; Rouse, Stephen

    2011-06-01

    In order to restore an extraoral maxillofacial defect, a moulage impression is commonly made with traditional impression materials. This technique has some disadvantages, including distortion of the site due to the weight of the impression material, changes in tissue location with modifications of the patient position, and the length of time and discomfort for the patient due to the impression procedure and materials used. The use of the commercially available 3dMDface™ System creates 3D images of soft tissues to form an anatomically accurate 3D surface image. Rapid prototyping converts the virtual designs from the 3dMDface™ System into a physical model by converting the data to a ZPrint (ZPR) CAD format file and a stereolithography (STL) file. The data, in conjunction with a Zprinter(®) 450 or a Stereolithography Apparatus (SLA), can be used to fabricate a model for prosthesis fabrication, without the disadvantages of the standard moulage technique. This article reviews this technique and how it can be applied to maxillofacial prosthetics. © 2011 by The American College of Prosthodontists.

  12. Integrated flexible manufacturing program for manufacturing automation and rapid prototyping

    Science.gov (United States)

    Brooks, S. L.; Brown, C. W.; King, M. S.; Simons, W. R.; Zimmerman, J. J.

    1993-01-01

    The Kansas City Division of Allied Signal Inc., as part of the Integrated Flexible Manufacturing Program (IFMP), is developing an integrated manufacturing environment. Several systems are being developed to produce standards and automation tools for specific activities within the manufacturing environment. The Advanced Manufacturing Development System (AMDS) is concentrating on information standards (STEP) and product data transfer; the Expert Cut Planner system (XCUT) is concentrating on machining operation process planning standards and automation capabilities; the Advanced Numerical Control system (ANC) is concentrating on NC data preparation standards and NC data generation tools; the Inspection Planning and Programming Expert system (IPPEX) is concentrating on inspection process planning, coordinate measuring machine (CMM) inspection standards and CMM part program generation tools; and the Intelligent Scheduling and Planning System (ISAPS) is concentrating on planning and scheduling tools for a flexible manufacturing system environment. All of these projects are working together to address information exchange, standardization, and information sharing to support rapid prototyping in a Flexible Manufacturing System (FMS) environment.

  13. Rapid Prototyping Human Interfaces Using Stretchable Strain Sensor

    Directory of Open Access Journals (Sweden)

    Tokiya Yamaji

    2017-01-01

    Full Text Available In the modern society with a variety of information electronic devices, human interfaces increase their importance in a boundary of a human and a device. In general, the human is required to get used to the device. Even if the device is designed as a universal device or a high-usability device, the device is not suitable for all users. The usability of the device depends on the individual user. Therefore, personalized and customized human interfaces are effective for the user. To create customized interfaces, we propose rapid prototyping human interfaces using stretchable strain sensors. The human interfaces comprise parts formed by a three-dimensional printer and the four strain sensors. The three-dimensional printer easily makes customized human interfaces. The outputs of the interface are calculated based on the sensor’s lengths. Experiments evaluate three human interfaces: a sheet-shaped interface, a sliding lever interface, and a tilting lever interface. We confirm that the three human interfaces obtain input operations with a high accuracy.

  14. NGS++: a library for rapid prototyping of epigenomics software tools.

    Science.gov (United States)

    Nordell Markovits, Alexei; Joly Beauparlant, Charles; Toupin, Dominique; Wang, Shengrui; Droit, Arnaud; Gevry, Nicolas

    2013-08-01

    The development of computational tools to enable testing and analysis of high-throughput-sequencing data is essential to modern genomics research. However, although multiple frameworks have been developed to facilitate access to these tools, comparatively little effort has been made at implementing low-level programming libraries to increase the speed and ease of their development. We propose NGS++, a programming library in C++11 specialized in manipulating both next-generation sequencing (NGS) datasets and genomic information files. This library allows easy integration of new formats and rapid prototyping of new functionalities with a focus on the analysis of genomic regions and features. It offers a powerful, yet versatile and easily extensible interface to read, write and manipulate multiple genomic file formats. By standardizing the internal data structures and presenting a common interface to the data parser, NGS++ offers an effective framework for epigenomics tool development. NGS++ was written in C++ using the C++11 standard. It requires minimal efforts to build and is well-documented via a complete docXygen guide, online documentation and tutorials. Source code, tests, code examples and documentation are available via the website at http://www.ngsplusplus.ca and the github repository at https://github.com/NGS-lib/NGSplusplus. nicolas.gevry@usherbrooke.ca or arnaud.droit@crchuq.ulaval.ca.

  15. Procedural Modeling for Rapid-Prototyping of Multiple Building Phases

    Science.gov (United States)

    Saldana, M.; Johanson, C.

    2013-02-01

    RomeLab is a multidisciplinary working group at UCLA that uses the city of Rome as a laboratory for the exploration of research approaches and dissemination practices centered on the intersection of space and time in antiquity. In this paper we present a multiplatform workflow for the rapid-prototyping of historical cityscapes through the use of geographic information systems, procedural modeling, and interactive game development. Our workflow begins by aggregating archaeological data in a GIS database. Next, 3D building models are generated from the ArcMap shapefiles in Esri CityEngine using procedural modeling techniques. A GIS-based terrain model is also adjusted in CityEngine to fit the building elevations. Finally, the terrain and city models are combined in Unity, a game engine which we used to produce web-based interactive environments which are linked to the GIS data using keyhole markup language (KML). The goal of our workflow is to demonstrate that knowledge generated within a first-person virtual world experience can inform the evaluation of data derived from textual and archaeological sources, and vice versa.

  16. Rapid prototyping and 3D-virtual models for operative dentistry education in Brazil.

    Science.gov (United States)

    Soares, Paulo Vinícius; de Almeida Milito, Giovana; Pereira, Fabrícia Araújo; Reis, Bruno Rodrigues; Soares, Carlos José; de Sousa Menezes, Murilo; de Freitas Santos-Filho, Paulo César

    2013-03-01

    Many dental students struggle for visual recognition when first exposed to the study of tooth cavity preparation in the operative dentistry laboratory. Rapid prototypes and virtual models of different cavity preparations were developed for the incoming first-year class of 2010 at the Dental School of Federal University of Uberlândia, Brazil, to help them to visualize the subtle differences in cavity preparations and are described in this article. Rapid prototyping techniques have been used in dental therapy, mainly for the fabrication of models to ease surgical planning in implantology, orthodontics, and maxillofacial prostheses. On the other hand, the application of these technologies associated with 3D-virtual models in dental education is waiting to be exploited, once they have significant potential to complement conventional training methods in dentistry.

  17. Design of rapid prototype of UAV line-of-sight stabilized control system

    Science.gov (United States)

    Huang, Gang; Zhao, Liting; Li, Yinlong; Yu, Fei; Lin, Zhe

    2018-01-01

    The line-of-sight (LOS) stable platform is the most important technology of UAV (unmanned aerial vehicle), which can reduce the effect to imaging quality from vibration and maneuvering of the aircraft. According to the requirement of LOS stability system (inertial and optical-mechanical combined method) and UAV's structure, a rapid prototype is designed using based on industrial computer using Peripheral Component Interconnect (PCI) and Windows RTX to exchange information. The paper shows the control structure, and circuit system including the inertial stability control circuit with gyro and voice coil motor driven circuit, the optical-mechanical stability control circuit with fast-steering-mirror (FSM) driven circuit and image-deviation-obtained system, outer frame rotary follower, and information-exchange system on PC. Test results show the stability accuracy reaches 5μrad, and prove the effectiveness of the combined line-of-sight stabilization control system, and the real-time rapid prototype runs stable.

  18. CAD – CAM PROCEDURE USING FOR RAPID PROTOTYPING WITH APPLICATION IN BIOMECHANICS

    Directory of Open Access Journals (Sweden)

    BRAUN Barbu

    2015-06-01

    Full Text Available The paper presents a new and efficient method for modeling some components with application in Biomechanics. It is shown the way in which this method could be successfully applied for orthopedic shoes, namely for foot insoles to correct any plantar deformities. The main advantages of the proposed method refer to low costs, successfully applying for different products for Biomechanics. The prototyped models via CAD/CAM method allowed a rapid and efficient improvement of their design. Another advantage refer to the fact that these can be properly and efficiently tested before prototyping by the point of view of mechanical stress, due to prior simulations, eliminating all costs meaning wastes or adjustments.

  19. Rapid Prototyping of High Performance Signal Processing Applications

    Science.gov (United States)

    Sane, Nimish

    Advances in embedded systems for digital signal processing (DSP) are enabling many scientific projects and commercial applications. At the same time, these applications are key to driving advances in many important kinds of computing platforms. In this region of high performance DSP, rapid prototyping is critical for faster time-to-market (e.g., in the wireless communications industry) or time-to-science (e.g., in radio astronomy). DSP system architectures have evolved from being based on application specific integrated circuits (ASICs) to incorporate reconfigurable off-the-shelf field programmable gate arrays (FPGAs), the latest multiprocessors such as graphics processing units (GPUs), or heterogeneous combinations of such devices. We, thus, have a vast design space to explore based on performance trade-offs, and expanded by the multitude of possibilities for target platforms. In order to allow systematic design space exploration, and develop scalable and portable prototypes, model based design tools are increasingly used in design and implementation of embedded systems. These tools allow scalable high-level representations, model based semantics for analysis and optimization, and portable implementations that can be verified at higher levels of abstractions and targeted toward multiple platforms for implementation. The designer can experiment using such tools at an early stage in the design cycle, and employ the latest hardware at later stages. In this thesis, we have focused on dataflow-based approaches for rapid DSP system prototyping. This thesis contributes to various aspects of dataflow-based design flows and tools as follows: 1. We have introduced the concept of topological patterns, which exploits commonly found repetitive patterns in DSP algorithms to allow scalable, concise, and parameterizable representations of large scale dataflow graphs in high-level languages. We have shown how an underlying design tool can systematically exploit a high

  20. A Language Translator for a Computer Aided Rapid Prototyping System.

    Science.gov (United States)

    1988-03-01

    53 Table 2. TYPICAL FUNCTIONS FOR NAVMACS AND PROPOSED NAVM ACSM ODEL II...development. Second, the use of prototyping in an automated en- vironment to provide guideline models for the entire life cycle. Use of automated tools. Al

  1. Applications of stereolithography for rapid prototyping of biologically compatible chip-based physiometers

    Science.gov (United States)

    Fuad, Nurul Mohd; Zhu, Feng; Kaslin, Jan; Wlodkowic, Donald

    2016-12-01

    Despite the growing demand and numerous applications for the biomedical community, the developments in millifluidic devices for small model organisms are limited compared to other fields of biomicrofluidics. The main reasons for this stagnanation are difficulties in prototyping of millimeter scale and high aspect ratio devices needed for large metazoan organisms. Standard photolithography is in this context a time consuming procedure not easily adapted for fabrication of molds with vertical dimensions above 1 mm. Moreover, photolithography is still largely unattainable to a gross majority of biomedical laboratories willing to pursue custom development of their own chip-based platforms due to costs and need for dedicated clean room facilities. In this work, we present application of high-definition additive manufacturing systems for fabrication of 3D printed moulds used in soft lithography. Combination of 3D printing with PDMS replica molding appears to be an alternative for millifluidic systems that yields rapid and cost effective prototyping pipeline. We investigated the important aspects on both 3D printed moulds and PDMS replicas such as geometric accuracies and surface topology. Our results demonstrated that SLA technologies could be applied for rapid and accurate fabrication of millifluidic devices for trapping of millimetre-sized specimens such as living zebrafish larvae. We applied the new manufacturing method in a proof-of-concept prototype device capable of trapping and immobilizing living zebrafish larvae for recording heart rate variation in cardio-toxicity experiments.

  2. SOAR telescope control system: a rapid prototype and development in LabVIEW

    Science.gov (United States)

    Ashe, Michael C.; Schumacher, German

    2000-06-01

    A Rapid Prototype and full development plan of the SOAR TCS is reviewed to show advances in: (1) Prototyping speed, which makes implementation and test of features faster than specification under older methods. This allows the development environment and prototype modules to become partners with and part of the specification documents. (2) Real-Time performance and reliability through use of RT Linux. (3) Visually Rich GUI development that allows an emphasis on `seeing' versus `reading'. (4) Long-Term DataLogging and Internet subscription service of all desired variables with instant recall of historical trend data. (5) A `plug-in' software architecture which enables rapid reconfiguration and reuse of the system and/or plug-ins utilizing LabVIEW graphical modules, a scripting language engine (in LabVIEW) and encapsulation of interfaces in `instrument-driver' style `plug-in' modules. (6) A platform- independent development environment and distributed architecture allowing secure internet observation and control via every major OS and hardware platform.

  3. A low cost rapid prototype platform for a three phase PFC rectifier application

    DEFF Research Database (Denmark)

    Haase, Frerk; Kouchaki, Alireza; Nymand, Morten

    2015-01-01

    In this paper the design and development of a low cost rapid prototype platform for a Three Phase PFC rectifier application is presented. The active rectifier consists of a SiC-MOSFET based PWM converter and a low cost rapid prototype platform for simulating and implementing the digital control...... is then performed using automatic code generation for embedded targets, which provided a close link between simulation and implementation of the PFC controller. The paper shows how this rapid prototype platform developed and how it was used for the design and implementation of the controller for a high efficient Si...

  4. Rapid Prototyping with Fourth Generation Systems - an Empirical Study

    DEFF Research Database (Denmark)

    Grønbæk, Kaj

    1989-01-01

    prototypes appear to stimulate constructive response. Reasons that developers should be aware of the tacit knowledge which plays an important part in users' work practices and should be involved early in the development process. Proposes three techniques to meet the requirements – participation, simulation...

  5. Novel Applications of Rapid Prototyping in Gamma-ray and X-ray Imaging

    Science.gov (United States)

    Miller, Brian W.; Moore, Jared W.; Gehm, Michael E.; Furenlid, Lars R.; Barrett, Harrison H.

    2010-01-01

    Advances in 3D rapid-prototyping printers, 3D modeling software, and casting techniques allow for the fabrication of cost-effective, custom components in gamma-ray and x-ray imaging systems. Applications extend to new fabrication methods for custom collimators, pinholes, calibration and resolution phantoms, mounting and shielding components, and imaging apertures. Details of the fabrication process for these components are presented, specifically the 3D printing process, cold casting with a tungsten epoxy, and lost-wax casting in platinum. PMID:22984341

  6. Rapid Prototyping Technologies and their Applications in Prosthodontics, a Review of Literature

    Science.gov (United States)

    Torabi, Kianoosh; Farjood, Ehsan; Hamedani, Shahram

    2015-01-01

    The early computer-aided design/computer-aided manufacturing (CAD/CAM) systems were relied exclusively on subtractive methods. In recent years, additive methods by employing rapid prototyping (RP) have progressed rapidly in various fields of dentistry as they have the potential to overcome known drawbacks of subtractive techniques such as fit problems. RP techniques have been exploited to build complex 3D models in medicine since the 1990s. RP has recently proposed successful applications in various dental fields, such as fabrication of implant surgical guides, frameworks for fixed and removable partial dentures, wax patterns for the dental prosthesis, zirconia prosthesis and molds for metal castings, and maxillofacial prosthesis and finally, complete dentures. This paper aimed to offer a comprehensive literature review of various RP methods, particularly in dentistry, that are expected to bring many improvements to the field. A search was made through MEDLINE database and Google scholar search engine. The keywords; ‘rapid prototyping’ and ‘dentistry’ were searched in title/abstract of publications; limited to 2003 to 2013, concerning past decade. The inclusion criterion was the technical researches that predominately included laboratory procedures. The exclusion criterion was meticulous clinical and excessive technical procedures. A total of 106 articles were retrieved, recited by authors and only 50 met the specified inclusion criteria for this review. Selected articles had used rapid prototyping techniques in various fields in dentistry through different techniques. This review depicted the different laboratory procedures employed in this method and confirmed that RP technique have been substantially feasible in dentistry. With advancement in various RP systems, it is possible to benefit from this technique in different dental practices, particularly in implementing dental prostheses for different applications. PMID:25759851

  7. Rapid-Prototyping of Application Specific Signal Processors (RASSP) Education and Facilitation

    National Research Council Canada - National Science Library

    Gadient, Anthony

    2000-01-01

    The Rapid-Prototyping of Application Specific Signal Processors (RASSP) program was a major DARPA/Tri-Service initiative to reinvent the process by which embedded digital signal processors were developed...

  8. Rapid Prototyping — A Tool for Presenting 3-Dimensional Digital Models Produced by Terrestrial Laser Scanning

    Directory of Open Access Journals (Sweden)

    Juho-Pekka Virtanen

    2014-07-01

    Full Text Available Rapid prototyping has received considerable interest with the introduction of affordable rapid prototyping machines. These machines can be used to manufacture physical models from three-dimensional digital mesh models. In this paper, we compare the results obtained with a new, affordable, rapid prototyping machine, and a traditional professional machine. Two separate data sets are used for this, both of which were acquired using terrestrial laser scanning. Both of the machines were able to produce complex and highly detailed geometries in plastic material from models based on terrestrial laser scanning. The dimensional accuracies and detail levels of the machines were comparable, and the physical artifacts caused by the fused deposition modeling (FDM technique used in the rapid prototyping machines could be found in both models. The accuracy of terrestrial laser scanning exceeded the requirements for manufacturing physical models of large statues and building segments at a 1:40 scale.

  9. Additive manufacturing technologies: 3D printing, rapid prototyping, and direct digital manufacturing

    National Research Council Canada - National Science Library

    Gibson, Ian; Rosen, David; Stucker, B

    2015-01-01

    .... This book provides a comprehensive overview of rapid prototyping technologies as well as support technologies such as software systems, vacuum casting, investment casting, plating, infiltration and other systems. This book also...

  10. [Application status of rapid prototyping technology in artificial bone based on reverse engineering].

    Science.gov (United States)

    Fang, Ao; Zheng, Min; Fan, Ding

    2015-02-01

    Artificial bone replacement has made an important contribution to safeguard human health and improve the quality of life. The application requirements of rapid prototyping technology based on reverse engineering in individualized artificial bone with individual differences are particularly urgent. This paper reviewed the current research and applications of rapid prototyping and reverse engineering in artificial bone. The research developments and the outlook of bone kinematics and dynamics simulation are also introduced.

  11. Rapid Prototyping of Simulated VIIRS Data in the SERVIR Fire Rapid Response System

    Science.gov (United States)

    Easson, G.; Kuszmaul, J. S.; Yarbrough, L. D.; Irwin, D.; Cherrington, E.

    2006-12-01

    A rapid prototyping capability experiment has been established involving the application of the SERVIR (Sistema Regional de Visualización y Monitoreo) decision support tool, which is NASA's and its partner agencies' tool to monitor groundcover and climatic conditions in Mesoamerica. As an information system, the SERVIR tool processes data products from multiple sources and the outcome is visualized through interactive digital maps, standard view map outputs or 3D real-time visualization. The focus of this research is one of the SERVIR Fire Rapid Response products known as the MODIS SERVIR Fire Extent Product, which was developed to meet the requirements of the Guatemalan Park Service. The credibility of SERVIR's monitoring tools currently depends upon NASA's MODIS data, which is nearing the end of its availability. This will make it necessary to transition to the planned replacement sensor, VIIRS. The impact of this transition on the performance of SERVIR's fire detection tools is the current focus of our investigation. A quantitative assessment of fire conditions in Guatemala is made using MODIS data and is compared to the anticipated performance using simulated data that would have been produced by a VIIRS-like sensor. Using a low-density geospatial database, the comparison is made for a number of dates from the 2003 Guatemalan fire season, where ground validation data is available. A comparative assessment is also made using the kappa statistic applied to the land classifications resulting from both the MODIS- and VIIRS- based fire detection algorithms.

  12. The Java Image Science Toolkit (JIST) for Rapid Prototyping and Publishing of Neuroimaging Software

    Science.gov (United States)

    Lucas, Blake C.; Bogovic, John A.; Carass, Aaron; Bazin, Pierre-Louis; Prince, Jerry L.; Pham, Dzung

    2010-01-01

    Non-invasive neuroimaging techniques enable extraordinarily sensitive and specific in vivo study of the structure, functional response and connectivity of biological mechanisms. With these advanced methods comes a heavy reliance on computer-based processing, analysis and interpretation. While the neuroimaging community has produced many excellent academic and commercial tool packages, new tools are often required to interpret new modalities and paradigms. Developing custom tools and ensuring interoperability with existing tools is a significant hurdle. To address these limitations, we present a new framework for algorithm development that implicitly ensures tool interoperability, generates graphical user interfaces, provides advanced batch processing tools, and, most importantly, requires minimal additional programming or computational overhead. Java-based rapid prototyping with this system is an efficient and practical approach to evaluate new algorithms since the proposed system ensures that rapidly constructed prototypes are actually fully-functional processing modules with support for multiple GUI's, a broad range of file formats, and distributed computation. Herein, we demonstrate MRI image processing with the proposed system for cortical surface extraction in large cross-sectional cohorts, provide a system for fully automated diffusion tensor image analysis, and illustrate how the system can be used as a simulation framework for the development of a new image analysis method. The system is released as open source under the Lesser GNU Public License (LGPL) through the Neuroimaging Informatics Tools and Resources Clearinghouse (NITRC). PMID:20077162

  13. Rapid BeagleBoard prototyping with MATLAB and Simulink

    CERN Document Server

    Qin, Fei

    2013-01-01

    This book is a fast-paced guide with practical, hands-on recipes which will show you how to prototype Beagleboard-based audio/video applications using Matlab/Simlink and Sourcery Codebench on a Windows host.Beagleboard Embedded Projects is great for students and academic researchers who have practical ideas and who want to build a proof-of-concept system on an embedded hardware platform quickly and efficiently. It is also useful for product design engineers who want to ratify their applications and reduce the time-to-market. It is assumed that you are familiar with Matlab/Simulink and have som

  14. Low-cost rapid prototyping of flexible plastic paper based microfluidic devices

    KAUST Repository

    Fan, Yiqiang

    2013-04-01

    This research presents a novel rapid prototyping method for paper-based flexible microfluidic devices. The microchannels were fabricated using laser ablation on a piece of plastic paper (permanent paper), the dimensions of the microchannels was carefully studied for various laser powers and scanning speeds. After laser ablation of the microchannels on the plastic paper, a transparent poly (methyl methacrylate)(PMMA) film was thermally bonded to the plastic paper to enclose the channels. After connection of tubing, the device was ready to use. An example microfluidic device (droplet generator) was also fabricated using this technique. Due to the flexibility of the fabricated device, this technique can be used to fabricate 3D microfluidic devices. The fabrication process was simple and rapid without any requirement of cleanroom facilities. © 2013 IEEE.

  15. Gene-modified stem cells combined with rapid prototyping techniques: a novel strategy for periodontal regeneration.

    Science.gov (United States)

    He, Huixia; Cao, Junkai; Wang, Dongsheng; Gu, Bing; Guo, Hong; Liu, Hongchen

    2010-03-01

    Periodontal disease, a worldwide prevalent chronic disease in adults, is characterized by the destruction of the periodontal supporting tissue including the cementum, periodontal ligament and alveolar bone. The regeneration of damaged periodontal tissue is the main goal of periodontal treatment. Because conventional periodontal treatments remain insufficient to attain complete and reliable periodontal regeneration, periodontal tissue engineering has emerged as a prospective alternative method for improving the regenerative capacity of periodontal tissue. However, the potential of periodontal regeneration seems to be limited by the understanding of the cellular and molecular events in the formation of periodontal tissue and by the insufficient collaboration of multi-disciplinary research that periodontal tissue engineering involves. In this paper, we first reviewed the recent advancements in stem cells, signaling factors, and scaffolds that relate to periodontal regeneration. Then we speculate that specific genes would improve regenerative capacity of these stem cells, which could differentiate into cementoblasts, osteoblasts and fibroblasts. In addition, the 3D scaffolds that mimic the different structure and physiologic functions of natural fibro-osseous tissue could be fabricated by rapid prototyping (RP) techniques. It was therefore hypothesized that gene-modified stem cells combined with rapid prototyping techniques would be a new strategy to promote more effective and efficient periodontal regeneration.

  16. Parametric Design and Rapid Prototyping of Installation Box for Vehicle Terminal PCB

    Directory of Open Access Journals (Sweden)

    Wang Xingxing

    2016-01-01

    Full Text Available Installation box for vehicle terminal PCB (Printed Circuit Board was took as research object, which is encountered in the process of project developing. Vehicle terminal PCB in actual development process was set as an example, point cloud data were acquired by three coordinate measuring method; Imageware software was used to reconstruct the vehicle terminal PCB model, basic size parameters of vehicle terminal PCB can be got and then design parameters of installation box for vehicle terminal PCB can be determined. Design of the installation box for vehicle terminal PCB was completed based on Solidworks software, then 3D modeling and 2D drawing of installation box for vehicle terminal PCB was gained. Up Plus 2 rapid prototype machine was used to manufacture installation box for vehicle terminal PCB rapidly based on 3D printing technology, then prototype of installation box for vehicle terminal PCB was obtained. It is of certain engineering significant for single (small amount manufacturing of installation box for general PCB.

  17. Effects of Hydrocarbon-Based Grease on Rapid Prototype Material Used for Grease Retention Shrouds

    Science.gov (United States)

    Zakrajsek, Andrew J.; Valco, Daniel J.; Street, Kenneth W., Jr.

    2010-01-01

    Effects of hydrocarbon-based greases on specific rapid prototype (RP) materials used to fabricate grease retention shrouds (GRS) were explored in this study. Grease retention shrouds are being considered as a way to maintain adequate grease lubrication at the gear mesh in a prototype research transmission system. Due to their design and manufacturing flexibility, rapid prototype materials were chosen for the grease retention shrouds. In order to gain a better understanding of the short and long term effects grease pose on RP materials, research was conducted on the interaction of hydrocarbon-based grease with RP materials. The materials used in this study were durable polyamide (nylon), acrylonitrile butadiene styrene (ABS), and WaterClear 10120. Testing was conducted using Mobilgrease 28 and Syn-Tech 3913G grease (gear coupling grease). These greases were selected due to their regular use with mechanical components. To investigate the effect that grease has on RP materials, the following methods were used to obtain qualitative and quantitative data: Fourier transform infrared spectroscopy (FT-IR), interference profilometer measurements, digital camera imaging, physical shape measurement, and visual observations. To record the changes in the RP materials due to contact with the grease, data was taken before and after the grease application. Results showed that the WaterClear 10120 RP material provided the best resistance to grease penetration as compared to nylon and ABS RP materials. The manufacturing process, and thus resulting surface conditions of the RP material, played a key role in the grease penetration properties and resilience of these materials.

  18. Rapid prototyping for patient-specific surgical orthopaedics guides: A systematic literature review.

    Science.gov (United States)

    Popescu, Diana; Laptoiu, Dan

    2016-06-01

    There has been a lot of hype surrounding the advantages to be gained from rapid prototyping processes in a number of fields, including medicine. Our literature review aims objectively to assess how effective patient-specific surgical guides manufactured using rapid prototyping are in a number of orthopaedic surgical applications. To this end, we carried out a systematic review to identify and analyse clinical and experimental literature studies in which rapid prototyping patient-specific surgical guides are used, focusing especially on those that entail quantifiable outcomes and, at the same time, providing details on the guides' design and type of manufacturing process. Here, it should be mentioned that in this field there are not yet medium- or long-term data, and no information on revisions. In the reviewed studies, the reported positive opinions on the use of rapid prototyping patient-specific surgical guides relate to the following main advantages: reduction in operating times, low costs and improvements in the accuracy of surgical interventions thanks to guides' personalisation. However, disadvantages and sources of errors which can cause patient-specific surgical guide failures are as well discussed by authors. Stereolithography is the main rapid prototyping process employed in these applications although fused deposition modelling or selective laser sintering processes can also satisfy the requirements of these applications in terms of material properties, manufacturing accuracy and construction time. Another of our findings was that individualised drill guides for spinal surgery are currently the favourite candidates for manufacture using rapid prototyping. Other emerging applications relate to complex orthopaedic surgery of the extremities: the forearm and foot. Several procedures such as osteotomies for radius malunions or tarsal coalition could become standard, thanks to the significant assistance provided by rapid prototyping patient-specific surgical

  19. Accuracy and reproducibility of dental replica models reconstructed by different rapid prototyping techniques

    NARCIS (Netherlands)

    Hazeveld, Aletta; Huddleston Slater, James J. R.; Ren, Yijin

    INTRODUCTION: Rapid prototyping is a fast-developing technique that might play a significant role in the eventual replacement of plaster dental models. The aim of this study was to investigate the accuracy and reproducibility of physical dental models reconstructed from digital data by several rapid

  20. Teaching Tip: Using Rapid Game Prototyping for Exploring Requirements Discovery and Modeling

    Science.gov (United States)

    Dalal, Nikunj

    2012-01-01

    We describe the use of rapid game prototyping as a pedagogic technique to experientially explore and learn requirements discovery, modeling, and specification in systems analysis and design courses. Students have a natural interest in gaming that transcends age, gender, and background. Rapid digital game creation is used to build computer games…

  1. Rapid prototyping of multiphase microfluidics with robotic cutters

    Science.gov (United States)

    Li, Zidong; Zhao, Zhengtuo; Lo, Joe Fu-jiou

    2014-03-01

    Microfluidic devices offer novel techniques to address biological and biomedical issues. Standard microfluidic fabrication uses photolithography to pattern channels on silicon wafers with high resolution. Even the relatively straightforward SU8 and soft lithography in microfluidics require investing and training in photolithography, which is also time consuming due to complicated thick resist procedures, including sensitive substrate pretreatment, coating, soft bake, expose, post-exposure bake, and developing steps. However, for applications where low resolution (>200 μm) and high turn-around (> 4 designs/day) prototyping are met with little or no lithography infrastructure, robotic cutters [1] offer flexible options for making glass and PDMS microfluidics. We describe the use of robotics cutters for designing microfluidic geometries, and compliment it with safe glass etching, with depths down to 60 μm. Soft lithography patterning of 200 μm thick PDMS membrane was also explored. Without high equipment investment and lengthy student training, both glass and PDMS microfluidics can be achieved in small facilities using this technique.

  2. Logic Foundry: Rapid Prototyping for FPGA-Based DSP Systems

    Directory of Open Access Journals (Sweden)

    Bhattacharyya Shuvra S

    2003-01-01

    Full Text Available We introduce the Logic Foundry, a system for the rapid creation and integration of FPGA-based digital signal processing systems. Recognizing that some of the greatest challenges in creating FPGA-based systems occur in the integration of the various components, we have proposed a system that targets the following four areas of integration: design flow integration, component integration, platform integration, and software integration. Using the Logic Foundry, a system can be easily specified, and then automatically constructed and integrated with system level software.

  3. Product management of making large pieces through Rapid Prototyping PolyJet® technology

    Science.gov (United States)

    Belgiu, G.; Cărăuşu, C.; Şerban, D.; Turc, C. G.

    2017-08-01

    The rapid prototyping process has already become a classic manufacturing process for parts and assemblies, either polymeric or metal parts. Besides the well-known advantages and disadvantages of the process, the use of 3D printers has a great inconvenience: the overall dimensions of the parts are limited. Obviously, there is a possibility to purchase a larger (and more expensive) 3D printer, but there are always larger pieces to be manufactured. One solution to this problem is the splitting of parts into several components that can be manufactured. The component parts can then be assembled in a single piece by known methods such as welding, gluing, screwing, etc. This paper shows our experience in making large pieces on the Strarasys® Objet24 printer, pieces larger than the tray sizes. The results obtained are valid for any 3D printer using the PolyJet® process.

  4. Rapid prototyping and parametric optimization of plastic acoustofluidic devices for blood-bacteria separation.

    Science.gov (United States)

    Silva, R; Dow, P; Dubay, R; Lissandrello, C; Holder, J; Densmore, D; Fiering, J

    2017-09-01

    Acoustic manipulation has emerged as a versatile method for microfluidic separation and concentration of particles and cells. Most recent demonstrations of the technology use piezoelectric actuators to excite resonant modes in silicon or glass microchannels. Here, we focus on acoustic manipulation in disposable, plastic microchannels in order to enable a low-cost processing tool for point-of-care diagnostics. Unfortunately, the performance of resonant acoustofluidic devices in plastic is hampered by a lack of a predictive model. In this paper, we build and test a plastic blood-bacteria separation device informed by a design of experiments approach, parametric rapid prototyping, and screening by image-processing. We demonstrate that the new device geometry can separate bacteria from blood while operating at 275% greater flow rate as well as reduce the power requirement by 82%, while maintaining equivalent separation performance and resolution when compared to the previously published plastic acoustofluidic separation device.

  5. RAPID PROTOTYPING OF EMBEDDED PROGRAMMABLE SYSTEMS ON FPGA FOR MULTIMEDIA APPLICATIONS

    Directory of Open Access Journals (Sweden)

    V. V. Kliuchenia

    2015-01-01

    Full Text Available This paper illustrates rapid prototyping method applied for mobile multimedia systems with L2L (lossless-to-lossy compression scheme. Debug module Xilinx ML-401 based on the FPGA (Filed Programmable Gate Array is taken as the basis. Microblaze soft-processor is used as the main control unit. Proposed DCT-IDCT cores are developed using VHDL hardware description language as FSL (Fast Simples Link coprocessors for Microblaze or standalone PLB (Processor Logical Bus acceleration peripheral. Result of image processing is displayed on the screen connected via VGA interface. Proposed recursive architecture of DCT-IDCT core can be used as a basis of L2L coder.

  6. Individually Fitted Hearing Aid Device Manufactured Using Rapid Prototyping Based on Ear CT. A Case Report.

    Science.gov (United States)

    Chrzan, R; Miechowicz, S; Urbanik, A; Markowska, O; Kudasik, T

    2009-05-15

    Rapid prototyping is the technology of automatic freeform fabrication of physical objects from virtual CAD (computer aided design) models. For medical objects the models may be created using data from CT, MR or rotational angiography. We descriobe the case of a 83-year-old woman with essential bilateral hearing impairment as the effect of chronic otitis media. An individually fitted hearing aid was produced for the patient using stereolithography technology and vacuum casting based on data obtained during ear CT. Rapid prototyping may help in manufacturing individually adjusted biomedical prostheses, reducing the time of device production and improving its fitting.

  7. Design and optimization of the micro-engine turbine rotor manufacturing using the rapid prototyping technology

    Science.gov (United States)

    Vdovin, R. A.; Smelov, V. G.

    2017-02-01

    This work describes the experience in manufacturing the turbine rotor for the micro-engine. It demonstrates the design principles for the complex investment casting process combining the use of the ProCast software and the rapid prototyping techniques. At the virtual modelling stage, in addition to optimized process parameters, the casting structure was improved to obtain the defect-free section. The real production stage allowed demonstrating the performance and fitness of rapid prototyping techniques for the manufacture of geometrically-complex engine-building parts.

  8. Design and rapid prototyping of DLC coated fractal surfaces for tissue engineering applications

    Energy Technology Data Exchange (ETDEWEB)

    Diaz-Lantada, A; Mosquera, A; Endrino, J L; Lafont, P, E-mail: adiaz@etsii.upm.es

    2010-11-01

    Several medical devices (both implantable and for in vitro diagnosis) benefit greatly from having microtextured surfaces that help to improve and promote phenomena such as osteointegracion and cell / tissue growth on the surface of a device. Normally, the use of abrasives or chemical attacks are employed for obtaining such surface microtextures, however, it is sometimes difficult to precisely control the final surface characteristics (porosity, roughness, among others) and consequently the related biological aspects. In this work, we propose an alternative process based on the use of fractal surface models for designing special surfaces, which helps controlling the desired contact properties (from the design stage) in multiple applications within biomedical engineering, especially regarding tissue engineering tasks. Manufacturing can be directly accomplished by means of rapid prototyping technologies. This method supposes a focus change from a conventional 'top-down' to a more versatile 'bottom-up' approach. Finally, in order to improve the possible biological response, the surfaces of the designed devices were coated with hydrogen-free amorphous carbon (a-C) thin films, known to be highly biocompatible materials. The films were deposited at room temperature using the vacuum filter cathodic arc technique. Our first prototypes have helped verify the viability of the approach and to validate the design, manufacturing and coating processes.

  9. Rapid prototyping compliant arterial phantoms for in-vitro studies and device testing

    Directory of Open Access Journals (Sweden)

    Biglino Giovanni

    2013-01-01

    Full Text Available Abstract Background Compliant vascular phantoms are desirable for in-vitro patient-specific experiments and device testing. TangoPlus FullCure 930® is a commercially available rubber-like material that can be used for PolyJet rapid prototyping. This work aims to gather preliminary data on the distensibility of this material, in order to assess the feasibility of its use in the context of experimental cardiovascular modelling. Methods The descending aorta anatomy of a volunteer was modelled in 3D from cardiovascular magnetic resonance (CMR images and rapid prototyped using TangoPlus. The model was printed with a range of increasing wall thicknesses (0.6, 0.7, 0.8, 1.0 and 1.5 mm, keeping the lumen of the vessel constant. Models were also printed in both vertical and horizontal orientations, thus resulting in a total of ten specimens. Compliance tests were performed by monitoring pressure variations while gradually increasing and decreasing internal volume. Knowledge of distensibility was thus derived and then implemented with CMR data to test two applications. Firstly, a patient-specific compliant model of hypoplastic aorta suitable for connection in a mock circulatory loop for in-vitro tests was manufactured. Secondly, the right ventricular outflow tract (RVOT of a patient necessitating pulmonary valve replacement was printed in order to physically test device insertion and assess patient’s suitability for percutaneous pulmonary valve intervention. Results The distensibility of the material was identified in a range from 6.5 × 10-3 mmHg-1 for the 0.6 mm case, to 3.0 × 10-3 mmHg-1 for the 1.5 mm case. The models printed in the vertical orientation were always more compliant than their horizontal counterpart. Rapid prototyping of a compliant hypoplastic aorta and of a RVOT anatomical model were both feasible. Device insertion in the RVOT model was successful. Conclusion Values of distensibility, compared with literature data, show that Tango

  10. Development of Experimental Setup of Metal Rapid Prototyping Machine using Selective Laser Sintering Technique

    Science.gov (United States)

    Patil, S. N.; Mulay, A. V.; Ahuja, B. B.

    2016-08-01

    Unlike in the traditional manufacturing processes, additive manufacturing as rapid prototyping, allows designers to produce parts that were previously considered too complex to make economically. The shift is taking place from plastic prototype to fully functional metallic parts by direct deposition of metallic powders as produced parts can be directly used for desired purpose. This work is directed towards the development of experimental setup of metal rapid prototyping machine using selective laser sintering and studies the various parameters, which plays important role in the metal rapid prototyping using SLS technique. The machine structure in mainly divided into three main categories namely, (1) Z-movement of bed and table, (2) X-Y movement arrangement for LASER movements and (3) feeder mechanism. Z-movement of bed is controlled by using lead screw, bevel gear pair and stepper motor, which will maintain the accuracy of layer thickness. X-Y movements are controlled using timing belt and stepper motors for precise movements of LASER source. Feeder mechanism is then developed to control uniformity of layer thickness metal powder. Simultaneously, the study is carried out for selection of material. Various types of metal powders can be used for metal RP as Single metal powder, mixture of two metals powder, and combination of metal and polymer powder. Conclusion leads to use of mixture of two metals powder to minimize the problems such as, balling effect and porosity. Developed System can be validated by conducting various experiments on manufactured part to check mechanical and metallurgical properties. After studying the results of these experiments, various process parameters as LASER properties (as power, speed etc.), and material properties (as grain size and structure etc.) will be optimized. This work is mainly focused on the design and development of cost effective experimental setup of metal rapid prototyping using SLS technique which will gives the feel of

  11. Textiles Objective and Sensory Evaluation in Rapid Prototyping

    Directory of Open Access Journals (Sweden)

    Eugenija STRAZDIENE

    2011-11-01

    Full Text Available Most consumer purchases nowadays are driven by sensory attraction and good feeling. From this standpoint textile and fashion industries need new methods to evaluate fabric quality and to respond to consumer expectations. Recently the implementation of sensory analysis in the process of material characterization has drawn much international attention. So, the aim of the research was to find dependencies between the results of sensory analysis and objective fabric behaviour evaluation performed using KES-F and Griff-Tester devices. The later method was developed at Kaunas University of Technology and is based on fabric extraction through a rounded hole, thus describing the behaviour of textile materials and their tactile properties by one complex criterion.http://dx.doi.org/10.5755/j01.ms.17.4.778

  12. Construction of crystal structure prototype database: methods and applications.

    Science.gov (United States)

    Su, Chuanxun; Lv, Jian; Li, Quan; Wang, Hui; Zhang, Lijun; Wang, Yanchao; Ma, Yanming

    2017-04-26

    Crystal structure prototype data have become a useful source of information for materials discovery in the fields of crystallography, chemistry, physics, and materials science. This work reports the development of a robust and efficient method for assessing the similarity of structures on the basis of their interatomic distances. Using this method, we proposed a simple and unambiguous definition of crystal structure prototype based on hierarchical clustering theory, and constructed the crystal structure prototype database (CSPD) by filtering the known crystallographic structures in a database. With similar method, a program structure prototype analysis package (SPAP) was developed to remove similar structures in CALYPSO prediction results and extract predicted low energy structures for a separate theoretical structure database. A series of statistics describing the distribution of crystal structure prototypes in the CSPD was compiled to provide an important insight for structure prediction and high-throughput calculations. Illustrative examples of the application of the proposed database are given, including the generation of initial structures for structure prediction and determination of the prototype structure in databases. These examples demonstrate the CSPD to be a generally applicable and useful tool for materials discovery.

  13. Construction of crystal structure prototype database: methods and applications

    Science.gov (United States)

    Su, Chuanxun; Lv, Jian; Li, Quan; Wang, Hui; Zhang, Lijun; Wang, Yanchao; Ma, Yanming

    2017-04-01

    Crystal structure prototype data have become a useful source of information for materials discovery in the fields of crystallography, chemistry, physics, and materials science. This work reports the development of a robust and efficient method for assessing the similarity of structures on the basis of their interatomic distances. Using this method, we proposed a simple and unambiguous definition of crystal structure prototype based on hierarchical clustering theory, and constructed the crystal structure prototype database (CSPD) by filtering the known crystallographic structures in a database. With similar method, a program structure prototype analysis package (SPAP) was developed to remove similar structures in CALYPSO prediction results and extract predicted low energy structures for a separate theoretical structure database. A series of statistics describing the distribution of crystal structure prototypes in the CSPD was compiled to provide an important insight for structure prediction and high-throughput calculations. Illustrative examples of the application of the proposed database are given, including the generation of initial structures for structure prediction and determination of the prototype structure in databases. These examples demonstrate the CSPD to be a generally applicable and useful tool for materials discovery.

  14. Development of a drivable hybrid drive prototype in a rapid prototyping environment; Entwicklung einer Antriebssteuerung fuer ein Hybridfahrzeug in einer Rapid-Prototyping-Umgebung

    Energy Technology Data Exchange (ETDEWEB)

    Beck, Klaus [ETAS GmbH, Stuttgart (Germany); Escherle, Thomas; Nazareth, Dieter [Hochschule Landshut (Germany). Fakultaet fuer Informatik

    2010-07-01

    At least since the automotive crisis hybrid drives for motor vehicles resound throughout the land. All automobile manufacturers and many suppliers are working on appropriate concepts and components. In order to train students in step with actual practice on this relevant topics, mechanical engineering professor Dr. Prexler hat the idea to develop a drivable hybrid drive prototype with students within three terms. A joint project of the departments of mechanical engineering, electrical engineering and information technology at university of Landshut succeeded in developing a drivable serial plug-in hybrid named ''MBL-ex-drive''. (orig.)

  15. A novel 3D template for mandible and maxilla reconstruction: Rapid prototyping using stereolithography

    Directory of Open Access Journals (Sweden)

    Samir Kumta

    2015-01-01

    Full Text Available Introduction: Replication of the exact three-dimensional (3D structure of the maxilla and mandible is now a priority whilst attempting reconstruction of these bones to attain a complete functional and aesthetic rehabilitation. We hereby present the process of rapid prototyping using stereolithography to produce templates for modelling bone grafts and implants for maxilla/mandible reconstructions, its applications in tumour/trauma, and outcomes for primary and secondary reconstruction. Materials and Methods: Stereolithographic template-assisted reconstruction was used on 11 patients for the reconstruction of the mandible/maxilla primarily following tumour excision and secondarily for the realignment of post-traumatic malunited fractures or deformity corrections. Data obtained from the computed tomography (CT scans with 1-mm resolution were converted into a computer-aided design (CAD using the CT Digital Imaging and Communications in Medicine (DICOM data. Once a CAD model was constructed, it was converted into a stereolithographic format and then processed by the rapid prototyping technology to produce the physical anatomical model using a resin. This resin model replicates the native mandible, which can be thus used off table as a guide for modelling the bone grafts. Discussion: This conversion of two-dimensional (2D data from CT scan into 3D models is a very precise guide to shaping the bone grafts. Further, this CAD can reconstruct the defective half of the mandible using the mirror image principle, and the normal anatomical model can be created to aid secondary reconstructions. Conclusion: This novel approach allows a precise translation of the treatment plan directly to the surgical field. It is also an important teaching tool for implant moulding and fixation, and helps in patient counselling.

  16. A review of the issues surrounding three-dimensional computed tomography for medical modelling using rapid prototyping techniques

    Energy Technology Data Exchange (ETDEWEB)

    Bibb, Richard [Department of Design and Technology, Loughborough University, Ashby Road, Loughborough, Leicestershire LE11 3TU (United Kingdom)], E-mail: r.j.bibb@lboro.ac.uk; Winder, John [Health and Rehabilitation Sciences Research Institute, University of Ulster, Shore Road, Newtownabbey, BT37 0QB (United Kingdom)], E-mail: rj.winder@ulster.ac.uk

    2010-02-15

    This technical note aims to raise awareness amongst radiographers of the application of Computed Tomography data in the production of models using Rapid Prototyping technologies. It also aims to provide radiographers with recommendations that will assist them in providing three-dimensional Computed Tomography data that can fulfil the requirements of medical modelling. Potential problem areas in data acquisition and transfer are discussed and suggestions are given for methods that aim to avoid these.

  17. Topic Space: Rapid Prototyping a Mobile Augmented Reality Recommendation App

    Directory of Open Access Journals (Sweden)

    Jim Hahn

    2015-10-01

    Full Text Available With funding from an Institute of Museum and Library Services (IMLS Sparks! Ignition Grant, researchers from the University of Illinois Library designed and tested a mobile recommender app with augmented reality features. By embedding open source optical character recognition software into a “Topic Space” module, the augmented reality app can recognize call numbers on a book in the library and suggest relevant items that are not shelved nearby. Topic Space can also show users items that are normally shelved in the starting location but that are currently checked out. Using formative UX methods, grant staff shaped app interface and functionality through early user testing. This paper reports results of UX testing; a redesigned mobile interface, and provides considerations on the future development of personalized recommendation functionality.

  18. Rapid prototyping as a Tool for Designing and Manufacturing of Customised Anatomical Implants

    OpenAIRE

    RM Sherekar; AN Pawar; SV Bhalerao

    2014-01-01

    Rapid prototyping (RP) technologies are mostly related with applications in the product development and the design process as well as with small batch manufacturing. Due to their comparatively high rapidity and flexibility, however, they have also been engaged in various non-manufacturing applications. A field that attracts increasingly more attention by the scientific community is related to the application of technologies in medicine and health care. The associated research is focused both ...

  19. Rapid prototyping of centrifugal microfluidic modules for point of care blood testing

    CSIR Research Space (South Africa)

    Madzivhandila, Phophi

    2016-11-01

    Full Text Available We present modular centrifugal microfluidic devices that enable a series of blood tests to be performed towards a full blood count. The modular approach allows for rapid prototyping of device components in a generic format to complete different...

  20. A prototype Lab Box with DSK 'C6711/13 for rapid DSP algorithm development

    OpenAIRE

    Bertini, Graziano

    2007-01-01

    A system based on the TMS320C6711 DSK Starter Kit, enclosed in a special chassis, designed for real-time DSP algorithms testing, is described. Some evaluation of MATLab software Rapid Prototyping tools for a "Virtual Dubbing" application on damaged speech is also given.

  1. Rapid Prototyping 3D Model in Treatment of Pediatric Hip Dysplasia: A Case Report.

    Science.gov (United States)

    Holt, Andrew M; Starosolski, Zbigniew; Kan, J Herman; Rosenfeld, Scott B

    2017-01-01

    Rapid prototyping is an emerging technology that integrates common medical imaging with specialized production mechanisms to create detailed anatomic replicas. 3D-printed models of musculoskeletal anatomy have already proven useful in orthopedics and their applications continue to expand. We present the case of a 10 year-old female with Down syndrome and left acetabular dysplasia and chronic hip instability who underwent periacetabular osteotomy. A rapid prototyping 3D model was created to better understand the anatomy, counsel the family about the problem and the surgical procedure, as well as guide surgical technique. The intricate detail and size match of the model with the patient's anatomy offered unparalleled, hands-on experience with the patient's anatomy pre-operatively and improved surgical precision. Our experience with rapid prototyping confirmed its ability to enhance orthopedic care by improving the surgeon's ability to understand complex anatomy. Additionally, we report a new application utilizing intraoperative fluoroscopic comparison of the model and patient to ensure surgical precision and minimize the risk of complications. This technique could be used in other challenging cases. The increasing availability of rapid prototyping welcomes further use in all areas of orthopedics.

  2. Low-Cost Rapid Prototyping of Whole-Glass Microfluidic Devices

    Science.gov (United States)

    Yuen, Po Ki; Goral, Vasiliy N.

    2012-01-01

    A low-cost, straightforward, rapid prototyping of whole-glass microfluidic devices is presented using glass-etching cream that can be easily purchased in local stores. A self-adhered vinyl stencil cut out by a desktop digital craft cutter was used as an etching mask for patterning microstructures in glass using the glass-etching cream. A specific…

  3. Additive manufacturing technologies 3D printing, rapid prototyping, and direct digital manufacturing

    CERN Document Server

    Gibson, Ian; Stucker, Brent

    2015-01-01

    This book covers in detail the various aspects of joining materials to form parts. A conceptual overview of rapid prototyping and layered manufacturing is given,  beginning with the fundamentals so that readers can get up to speed quickly. Unusual and emerging applications such as micro-scale manufacturing, medical applications, aerospace, and rapid manufacturing are also discussed. This book provides a comprehensive overview of rapid prototyping technologies as well as support technologies such as software systems, vacuum casting, investment casting, plating, infiltration and other systems. This book also: Reflects recent developments and trends and adheres to the ASTM, SI, and other standards Includes chapters on automotive technology, aerospace technology and low-cost AM technologies Provides a broad range of technical questions to ensure comprehensive understanding of the concepts covered  

  4. Accuracy Assessment of Using Rapid Prototyping Drill Templates for Atlantoaxial Screw Placement: A Cadaver Study

    Directory of Open Access Journals (Sweden)

    Shuai Guo

    2016-01-01

    Full Text Available Purpose. To preliminarily evaluate the feasibility and accuracy of using rapid prototyping drill templates (RPDTs for C1 lateral mass screw (C1-LMS and C2 pedicle screw (C2-PS placement. Methods. 23 formalin-fixed craniocervical cadaver specimens were randomly divided into two groups. In the conventional method group, intraoperative fluoroscopy was used to assist the screw placement. In the RPDT navigation group, specific RPDTs were constructed for each specimen and were used intraoperatively for screw placement navigation. The screw position, the operating time, and the fluoroscopy time for each screw placement were compared between the 2 groups. Results. Compared with the conventional method, the RPDT technique significantly increased the placement accuracy of the C2-PS (p0.05. Moreover, the RPDT technique significantly decreased the operating and fluoroscopy times. Conclusion. Using RPDTs significantly increases the accuracy of C1-LMS and C2-PS placement while decreasing the screw placement time and the radiation exposure. Due to these advantages, this approach is worth promoting for use in the Harms technique.

  5. Simulation and Rapid Prototyping of Adaptive Control Systems using the Adaptive Blockset for Simulink

    DEFF Research Database (Denmark)

    Ravn, Ole

    1998-01-01

    The paper describes the design considerations and implementational aspects of the Adaptive Blockset for Simulink which has been developed in a prototype implementation. The concept behind the Adaptive Blockset for Simulink is to bridge the gap between simulation and prototype controller...... implementation. This is done using the code generation capabilities of Real Time Workshop in combination with C s-function blocks for adaptive control in Simulink. In the paper the design of each group of blocks normally found in adaptive controllers is outlined. The block types are, identification, controller...... design, controller and state variable filter.The use of the Adaptive Blockset is demonstrated using a simple laboratory setup. Both the use of the blockset for simulation and for rapid prototyping of a real-time controller are shown....

  6. Studies on the Process Parameters of Rapid Prototyping Technique (Stereolithography for the Betterment of Part Quality

    Directory of Open Access Journals (Sweden)

    Raju Bangalore Singe Gowda

    2014-01-01

    Full Text Available Rapid prototyping (RP has evolved as frontier technology in the recent times, which allows direct transformation of CAD files into functional prototypes where it tremendously reduces the lead time to produce physical prototypes necessary for design verification, fit, and functional analysis by generating the prototypes directly from the CAD data. Part quality in the rapid prototyping process is a function of build parameters such as hatch cure depth, layer thickness, orientation, and hatch spacing. Thus an attempt was made to identify, study, and optimize the process parameters governing the system which are related to part characteristics using Taguchi experimental design techniques quality. The part characteristics can be divided into physical part and mechanical part characteristics. The physical characteristics are surface finish, dimensional accuracy, distortion, layer thickness, hatch cure, and hatch file, whereas mechanical characteristics are flexural strength, ultimate tensile strength, and impact strength. Thus, this paper proposes to characterize the influence of the physical build parameters over the part quality. An L9 orthogonal array was designed with the minimum number of experimental runs with desired parameter settings and also by analysis tools such as ANOVA (analysis of variance. Establishment of experimentally verified correlations between the physical part characteristics and mechanical part characteristics to obtain an optimal process parameter level for betterment of part quality is obtained. The process model obtained by the empirical relation can be used to determine the strength of the prototype for the given set of parameters that shows the dependency of strength, which are essential for designers and RP machine users.

  7. Rapid Prototyping of Polymeric Nanopillars by 3D Direct Laser Writing for Controlling Cell Behavior.

    Science.gov (United States)

    Buch-Månson, Nina; Spangenberg, Arnaud; Gomez, Laura Piedad Chia; Malval, Jean-Pierre; Soppera, Olivier; Martinez, Karen L

    2017-08-23

    Mammalian cells have been widely shown to respond to nano- and microtopography that mimics the extracellular matrix. Synthetic nano- and micron-sized structures are therefore of great interest in the field of tissue engineering, where polymers are particularly attractive due to excellent biocompatibility and versatile fabrication methods. Ordered arrays of polymeric pillars provide a controlled topographical environment to study and manipulate cells, but processing methods are typically either optimized for the nano- or microscale. Here, we demonstrate polymeric nanopillar (NP) fabrication using 3D direct laser writing (3D DLW), which offers a rapid prototyping across both size regimes. The NPs are interfaced with NIH3T3 cells and the effect of tuning geometrical parameters of the NP array is investigated. Cells are found to adhere on a wide range of geometries, but the interface depends on NP density and length. The Cell Interface with Nanostructure Arrays (CINA) model is successfully extended to predict the type of interface formed on different NP geometries, which is found to correlate with the efficiency of cell alignment along the NPs. The combination of the CINA model with the highly versatile 3D DLW fabrication thus holds the promise of improved design of polymeric NP arrays for controlling cell growth.

  8. A novel low-cost mobile robot for rapid prototyping of precision farming applications

    DEFF Research Database (Denmark)

    Jensen, Kjeld; Neerup, Mathias Mikkel; Larsen, Leon Bonde

    field experiments using field robots which is typically a demanding task in terms of time consumption and logistics. Small indoor robots are sometimes used to emulate the larger field robots which allows for rapid prototyping and intermediate testing in the laboratory before moving to the field...... experiments. In this work we present a novel FrobitPro robot platform designed for rapid prototyping of FroboMind field robot applications. FrobitPro has a fundamental design similar to many current wheeled and tracked robots such as the Kongskilde Robotti, and the workflow of migrating from simulation...... to FrobitPro to field robot is therefore merely a matter of using different low level interface components. The FrobitPro robot is capable of carrying larger sensors such as RTK- GNSS, LIDAR and 3d stereo vision cameras. The platform supports interchangeable wheels for accurate indoor driving as well...

  9. Applications of the Rapid Prototyping Technology to Manufacture the Pelton Runners

    Directory of Open Access Journals (Sweden)

    Dorian Nedelcu

    2013-05-01

    Full Text Available The paper presents an application of the Rapid Prototyping technology using Objet Desktop 3D Printer to manufacture two Pelton runners that are destined for experimental measurements on a Pelton microturbine. The runners are different by bucket’s number and the bucket’s geometry of the second runner is similar with those of the first runner, but scaled in all directions with the bucket’s numbers ratio.

  10. Wind Tunnel Model Design and Test Using Rapid Prototype Materials and Processes

    Science.gov (United States)

    2001-07-23

    UNCLASSIFIED WIND TUNNEL MODEL DESIGN AND TEST USING RAPID PROTOTYPE MATERIALS AND PROCESSES Richard R. Heisler and Clifford L. Ratliff The Johns Hopkins...deflection, and attach directly to the strongback with screws. A and tolerance deviations when the material was grown. schematic diagram of the RPM...constructed around the clay to contain the I. R. R. Heisler , "Final Test Report for the Wind pouring of silicon resin. Tunnel Test of the JHU/APL WTM-01 at

  11. Low-Cost Inkjet Printing Technology for the Rapid Prototyping of Transducers

    Science.gov (United States)

    Andò, Bruno; Baglio, Salvatore; Bulsara, Adi R.; Emery, Teresa; Marletta, Vincenzo; Pistorio, Antonio

    2017-01-01

    Recently, there has been an upsurge in efforts dedicated to developing low-cost flexible electronics by exploiting innovative materials and direct printing technologies. This interest is motivated by the need for low-cost mass-production, shapeable, and disposable devices, and the rapid prototyping of electronics and sensors. This review, following a short overview of main printing processes, reports examples of the development of flexible transducers through low-cost inkjet printing technology. PMID:28368318

  12. Low-Cost Inkjet Printing Technology for the Rapid Prototyping of Transducers.

    Science.gov (United States)

    Andò, Bruno; Baglio, Salvatore; Bulsara, Adi R; Emery, Teresa; Marletta, Vincenzo; Pistorio, Antonio

    2017-04-01

    Recently, there has been an upsurge in efforts dedicated to developing low-cost flexible electronics by exploiting innovative materials and direct printing technologies. This interest is motivated by the need for low-cost mass-production, shapeable, and disposable devices, and the rapid prototyping of electronics and sensors. This review, following a short overview of main printing processes, reports examples of the development of flexible transducers through low-cost inkjet printing technology.

  13. Rapid Prototyping of Chemical Microsensors Based on Molecularly Imprinted Polymers Synthesized by Two-Photon Stereolithography.

    Science.gov (United States)

    Gomez, Laura Piedad Chia; Spangenberg, Arnaud; Ton, Xuan-Anh; Fuchs, Yannick; Bokeloh, Frank; Malval, Jean-Pierre; Tse Sum Bui, Bernadette; Thuau, Damien; Ayela, Cédric; Haupt, Karsten; Soppera, Olivier

    2016-07-01

    Two-photon stereolithography is used for rapid prototyping of submicrometre molecularly imprinted polymer-based 3D structures. The structures are evaluated as chemical sensing elements and their specific recognition properties for target molecules are confirmed. The 3D design capability is exploited and highlighted through the fabrication of an all-organic molecularly imprinted polymeric microelectromechanical sensor. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. [Mandibular-driven simultaneous maxillo-mandibular distraction for hemifacial microsomia with rapid prototyping technology].

    Science.gov (United States)

    Gao, Quan-Wen; Song, Hui-Feng; Xu, Ming-Huo; Liu, Chun-Ming; Chai, Jia-Ke

    2013-11-01

    To explore the clinical application of mandibular-driven simultaneous maxillo-mandihular distraction to correct hemifacial microsomia with rapid prototyping technology. The patient' s skull resin model was manufactured with rapid prototyping technology. The osteotomy was designed on skull resin model. According to the preoperative design, the patients underwent Le Fort I osteotomy and mandibular ramus osteotomy. The internal mandible distractor was embedded onto the osteotomy position. The occlusal titanium pin was implanted. Distraction were carried out by mandibular-driven simultaneous maxillo-mandihular distraction 5 days after operation. The distraction in five patients was complete as designed. No infection and dysosteogenesis happened. The longest distance of distraction was 28 mm, and the shortest distance was 16 mm. The facial asymmetry deformity was significantly improved at the end of distraction. The ocelusal plane of patients obviously improved. Rapid prototyping technology is helpful to design precisely osteotomy before operation. Mandibular-driven simultaneous maxillo-mandibular distraction can correct hemifacial microsomia. It is worth to clinical application.

  15. Reconstruction of Frontal Bone With Custom-Made Prosthesis Using Rapid Prototyping.

    Science.gov (United States)

    Florentino, Vinícius Gabriel Barros; Mendonça, Diego Santiago de; Bezerra, Ariel Valente; Silva, Leonardo de Freitas; Pontes, Rafael Figueirêdo; Melo, Carlos Vinícius Mota de; Mello, Manoel de Jesus Rodrigues; de Aguiar, Andréa Silvia Walter

    2016-06-01

    Frontal bone fracture treatment is still an issue of research in craniofacial surgery and neurosurgery. The aims of the treatment are to reduce the complication risks and to keep the aesthetic of the face. Before the management of this fracture type, it is necessary to consider the permanence or not of the frontal sinus function. Rapid prototyping has been an aid tool on planning and simulation of the surgical procedure, improving the diagnostic quality and the implant manufacture, beyond reducing the operative time. Among the used materials on treatment of these fractures, titanium mesh shows large versatility and ease of handling. Poly(methyl methacrylate) has been used in defects of partial thickness or irregularities on cranial surface. The aim of this study is to report a case of a patient presenting sequelae of large fracture of anterior wall of frontal bone, treated by a titanium mesh associated with the customized poly(methyl methacrylate) implant from the rapid prototyping. It could be concluded that the use of this technique showed itself effective on patient treatment, and rapid prototyping demonstrated being a valuable tool showing predictable and satisfactory results.

  16. Implementation of Rapid Prototyping Tools for Power Loss and Cost Minimization of DC-DC Converters

    Directory of Open Access Journals (Sweden)

    Amruta V. Kulkarni

    2016-07-01

    Full Text Available In this paper, power loss and cost models of power electronic converters based on converter ratings and datasheet information are presented. These models aid in creating rapid prototypes which facilitate the component selection process. Through rapid prototyping, users can estimate power loss and cost which are essential in design decisions. The proposed approach treats main power electronic components of a converter as building blocks that can be arranged to obtain multiple topologies to facilitate rapid prototyping. In order to get system-level power loss and cost models, two processes are implemented. The first process automatically provides minimum power loss or cost estimates and identifies components for specific applications and ratings; the second process estimates power losses and costs of each component of interest as well as the whole system. Two examples are used to illustrate the proposed approaches—boost and buck converters in continuous conduction mode. Achieved cost and loss estimates are over 93% accurate when compared to measured losses and real cost data. This research presents derivations of the proposed models, experimental validation of the models and demonstration of a user friendly interface that integrates all the models. Tools presented in this paper are expected to be very useful for practicing engineers, designers, and researchers, and are flexible and adaptable with changing or new technologies and varying component prices.

  17. Rapid, low-cost prototyping of centrifugal microfluidic devices for effective implementation of various microfluidic components

    Directory of Open Access Journals (Sweden)

    Smith, Suzanne

    2015-05-01

    Full Text Available A centrifugal microfluidic platform to develop various microfluidic operations – the first of its kind in South Africa – is presented. Rapid and low-cost prototyping of centrifugal microfluidic disc devices, as well as a set-up to test the devices using centrifugal forces, is described. Preliminary results show that various microfluidic operations such as fluidic valving, transportation, and microfluidic droplet generation can be achieved. This work provides a complete centrifugal microfluidic platform and the building blocks on which to develop a variety of microfluidic applications and potential products rapidly and at a low cost.

  18. Reverse engineering--rapid prototyping of the skull in forensic trauma analysis.

    Science.gov (United States)

    Kettner, Mattias; Schmidt, Peter; Potente, Stefan; Ramsthaler, Frank; Schrodt, Michael

    2011-07-01

    Rapid prototyping (RP) comprises a variety of automated manufacturing techniques such as selective laser sintering (SLS), stereolithography, and three-dimensional printing (3DP), which use virtual 3D data sets to fabricate solid forms in a layer-by-layer technique. Despite a growing demand for (virtual) reconstruction models in daily forensic casework, maceration of the skull is frequently assigned to ensure haptic evidence presentation in the courtroom. Owing to the progress in the field of forensic radiology, 3D data sets of relevant cases are usually available to the forensic expert. Here, we present a first application of RP in forensic medicine using computed tomography scans for the fabrication of an SLS skull model in a case of fatal hammer impacts to the head. The report is intended to show that this method fully respects the dignity of the deceased and is consistent with medical ethics but nevertheless provides an excellent 3D impression of anatomical structures and injuries. © 2011 American Academy of Forensic Sciences.

  19. Rapid prototyping: porous titanium alloy scaffolds produced by selective laser melting for bone tissue engineering.

    Science.gov (United States)

    Warnke, Patrick H; Douglas, Timothy; Wollny, Patrick; Sherry, Eugene; Steiner, Martin; Galonska, Sebastian; Becker, Stephan T; Springer, Ingo N; Wiltfang, Jörg; Sivananthan, Sureshan

    2009-06-01

    Selective laser melting (SLM), a method used in the nuclear, space, and racing industries, allows the creation of customized titanium alloy scaffolds with highly defined external shape and internal structure using rapid prototyping as supporting external structures within which bone tissue can grow. Human osteoblasts were cultured on SLM-produced Ti6Al4V mesh scaffolds to demonstrate biocompatibility using scanning electron microscopy (SEM), fluorescence microscopy after cell vitality staining, and common biocompatibility tests (lactate dihydrogenase (LDH), 3-(4,5-dimethylthiazol-2-yl)-2, 5-diphenyltetrazolium bromide (MTT), 5-bromo-2-deoxyuridine (BrdU), and water soluble tetrazolium (WST)). Cell occlusion of pores of different widths (0.45-1.2 mm) was evaluated. Scaffolds were tested for resistance to compressive force. SEM investigations showed osteoblasts with well-spread morphology and multiple contact points. Cell vitality staining and biocompatibility tests confirmed osteoblast vitality and proliferation on the scaffolds. Pore overgrowth increased during 6 weeks' culture at pore widths of 0.45 and 0.5 mm, and in the course of 3 weeks for pore widths of 0.55, 0.6, and 0.7 mm. No pore occlusion was observed on pores of width 0.9-1.2 mm. Porosity and maximum compressive load at failure increased and decreased with increasing pore width, respectively. In summary, the scaffolds are biocompatible, and pore width influences pore overgrowth, resistance to compressive force, and porosity.

  20. Application of laser measuring, numerical simulation and rapid prototyping to titanium dental castings.

    Science.gov (United States)

    Wu, M; Tinschert, J; Augthun, M; Wagner, I; Schädlich-Stubenrauch, J; Sahm, P R; Spiekermann, H

    2001-03-01

    This paper describes a method of making titanium dental crowns by means of integrating laser measuring, numerical simulation and rapid prototype (RP) manufacture of wax patterns for the investment casting process. Four real tooth crowns (FDI No. 24, 25, 26, 27) were measured by means of 3D laser scanning. The laser digitized geometry of the crowns was processed and converted into standard CAD models in STL format, which is used by RP systems and numerical simulation software. Commercial software (MAGMASOFT) was used to simulate the casting process and optimize the runner and gating system (sprue) design. RP crowns were 'printed' directly on a ModelMaker II 3D Plotting System. A silicone negative mold (soft tool) was made from the RP crowns, then more than hundreds wax crowns were duplicated. The duplicated crowns were joined to the optimized runner and gating system. By using the investment casting process 20-25 replicas of each crown were made on a centrifugal casting machine. All castings were examined for porosity by X-ray radiographs. By using the integrated scanning, simulation, RP pattern and casting procedure, cast crowns, free of porosity, with excellent functional contour and a smooth surface finish, were obtained from the first casting trial. The coupling of laser digitizing and RP indicates a potential to replace the traditional 'impression taking and waxing' procedure in dental laboratory, with the quality of the cast titanium prostheses also being improved by using the numerically optimized runner and gating system design.

  1. New Design for Rapid Prototyping of Digital Master Casts for Multiple Dental Implant Restorations

    Science.gov (United States)

    Romero, Luis; Jiménez, Mariano; Espinosa, María del Mar; Domínguez, Manuel

    2015-01-01

    Aim This study proposes the replacement of all the physical devices used in the manufacturing of conventional prostheses through the use of digital tools, such as 3D scanners, CAD design software, 3D implants files, rapid prototyping machines or reverse engineering software, in order to develop laboratory work models from which to finish coatings for dental prostheses. Different types of dental prosthetic structures are used, which were adjusted by a non-rotatory threaded fixing system. Method From a digital process, the relative positions of dental implants, soft tissue and adjacent teeth of edentulous or partially edentulous patients has been captured, and a maser working model which accurately replicates data relating to the patients oral cavity has been through treatment of three-dimensional digital data. Results Compared with the conventional master cast, the results show a significant cost savings in attachments, as well as an increase in the quality of reproduction and accuracy of the master cast, with the consequent reduction in the number of patient consultation visits. The combination of software and hardware three-dimensional tools allows the optimization of the planning of dental implant-supported rehabilitations protocol, improving the predictability of clinical treatments and the production cost savings of master casts for restorations upon implants. PMID:26696528

  2. Rapid Prototyping of Poly(methyl methacrylate) Microfluidic Systems Using Solvent Imprinting and Bonding

    Science.gov (United States)

    Sun, Xiuhua; Peeni, Bridget A.; Yang, Weichun; Becerril, Hector A.

    2011-01-01

    We have developed a method for rapid prototyping of hard polymer microfluidic systems using solvent imprinting and bonding. We investigated the applicability of patterned SU-8 photoresist on glass as an easily fabricated template for solvent imprinting. Poly(methyl methacrylate) (PMMA) exposed to acetonitrile for 2 min then had an SU-8 template pressed into the surface for 10 min, which provided appropriately imprinted channels and a suitable surface for bonding. After a PMMA cover plate had also been exposed to acetonitrile for 2 min, the imprinted and top PMMA pieces could be bonded together at room temperature with appropriate pressure. The total fabrication time was less than 15 min. Under the optimized fabrication conditions, nearly 30 PMMA chips could be replicated using a single patterned SU-8 master with high chip-to-chip reproducibility. Relative standard deviations were 2.3% and 5.4% for the widths and depths of the replicated channels, respectively. Fluorescently labeled amino acid and peptide mixtures were baseline separated using these PMMA microchips in <15 s. Theoretical plate numbers in excess of 5000 were obtained for a ~3 cm separation distance, and the migration time relative standard deviation for an amino acid peak was 1.5% for intra-day and 2.2% for inter-day analysis. This new solvent imprinting and bonding approach significantly simplifies the process for fabricating microfluidic structures in hard polymers such as PMMA. PMID:17466320

  3. A microcontroller platform for the rapid prototyping of functional electrical stimulation-based gait neuroprostheses.

    Science.gov (United States)

    Luzio de Melo, Paulo; da Silva, Miguel Tavares; Martins, Jorge; Newman, Dava

    2015-05-01

    Functional electrical stimulation (FES) has been used over the last decades as a method to rehabilitate lost motor functions of individuals with spinal cord injury, multiple sclerosis, and post-stroke hemiparesis. Within this field, researchers in need of developing FES-based control solutions for specific disabilities often have to choose between either the acquisition and integration of high-performance industry-level systems, which are rather expensive and hardly portable, or develop custom-made portable solutions, which despite their lower cost, usually require expert-level electronic skills. Here, a flexible low-cost microcontroller-based platform for rapid prototyping of FES neuroprostheses is presented, designed for reduced execution complexity, development time, and production cost. For this reason, the Arduino open-source microcontroller platform was used, together with off-the-shelf components whenever possible. The developed system enables the rapid deployment of portable FES-based gait neuroprostheses, being flexible enough to allow simple open-loop strategies but also more complex closed-loop solutions. The system is based on a modular architecture that allows the development of optimized solutions depending on the desired FES applications, even though the design and testing of the platform were focused toward drop foot correction. The flexibility of the system was demonstrated using two algorithms targeting drop foot condition within different experimental setups. Successful bench testing of the device in healthy subjects demonstrated these neuroprosthesis platform capabilities to correct drop foot. Copyright © 2015 International Center for Artificial Organs and Transplantation and Wiley Periodicals, Inc.

  4. Rapid Prototyping for In Vitro Knee Rig Investigations of Prosthetized Knee Biomechanics: Comparison with Cobalt-Chromium Alloy Implant Material

    Directory of Open Access Journals (Sweden)

    Christian Schröder

    2015-01-01

    Full Text Available Retropatellar complications after total knee arthroplasty (TKA such as anterior knee pain and subluxations might be related to altered patellofemoral biomechanics, in particular to trochlear design and femorotibial joint positioning. A method was developed to test femorotibial and patellofemoral joint modifications separately with 3D-rapid prototyped components for in vitro tests, but material differences may further influence results. This pilot study aims at validating the use of prostheses made of photopolymerized rapid prototype material (RPM by measuring the sliding friction with a ring-on-disc setup as well as knee kinematics and retropatellar pressure on a knee rig. Cobalt-chromium alloy (standard prosthesis material, SPM prostheses served as validation standard. Friction coefficients between these materials and polytetrafluoroethylene (PTFE were additionally tested as this latter material is commonly used to protect pressure sensors in experiments. No statistical differences were found between friction coefficients of both materials to PTFE. UHMWPE shows higher friction coefficient at low axial loads for RPM, a difference that disappears at higher load. No measurable statistical differences were found in knee kinematics and retropatellar pressure distribution. This suggests that using polymer prototypes may be a valid alternative to original components for in vitro TKA studies and future investigations on knee biomechanics.

  5. Using 3D Printing for Rapid Prototyping of Characterization Tools for Investigating Powder Blend Behavior.

    Science.gov (United States)

    Hirschberg, Cosima; Boetker, Johan P; Rantanen, Jukka; Pein-Hackelbusch, Miriam

    2018-02-01

    There is an increasing need to provide more detailed insight into the behavior of particulate systems. The current powder characterization tools are developed empirically and in many cases, modification of existing equipment is difficult. More flexible tools are needed to provide understanding of complex powder behavior, such as mixing process and segregation phenomenon. An approach based on the fast prototyping of new powder handling geometries and interfacing solutions for process analytical tools is reported. This study utilized 3D printing for rapid prototyping of customized geometries; overall goal was to assess mixing process of powder blends at small-scale with a combination of spectroscopic and mechanical monitoring. As part of the segregation evaluation studies, the flowability of three different paracetamol/filler-blends at different ratios was investigated, inter alia to define the percolation thresholds. Blends with a paracetamol wt% above the percolation threshold were subsequently investigated in relation to their segregation behavior. Rapid prototyping using 3D printing allowed designing two funnels with tailored flow behavior (funnel flow) of model formulations, which could be monitored with an in-line near-infrared (NIR) spectrometer. Calculating the root mean square (RMS) of the scores of the two first principal components of the NIR spectra visualized spectral variation as a function of process time. In a same setup, mechanical properties (basic flow energy) of the powder blend were monitored during blending. Rapid prototyping allowed for fast modification of powder testing geometries and easy interfacing with process analytical tools, opening new possibilities for more detailed powder characterization.

  6. Habitat Demonstration Unit Project: Leadership and Management Strategies for a Rapid Prototyping Project

    Science.gov (United States)

    Kennedy, Kriss J.; Toup, Larry; Gill, Tracy; Tri, Terry; Howe, Scott; Smitherman, David

    2011-01-01

    This paper gives an overview of the National Aeronautics and Space Administration (NASA) led multi-center Habitat Demonstration Unit (HDU) project leadership and management strategies being used by the NASA HDU team for a rapid prototyping project. The HDU project team constructed and tested an analog prototype lunar surface habitat/laboratory called the Pressurized Excursion Module (PEM) during 2010. The prototype unit subsystems were integrated in a short amount of time, utilizing a tiger team rapid prototyping approach that brought together over 20 habitation-related technologies and innovations from a variety of NASA centers. This paper describes the leadership and management strategies as well as lessons learned pertaining to leading and managing a multi-center diverse team in a rapid prototype environment. The PEM configuration went from a paper design to an operational surface habitat demonstration unit in less than 12 months. The HDU project is part of the strategic plan from the Exploration Systems Mission Directorate (ESMD) Directorate Integration Office (DIO) and the Exploration Mission Systems Office (EMSO) to test destination elements in analog environments. The 2011 HDU-Deep Space Habitat (DSH) configuration will build upon the PEM work, and emphasize validity of crew operations (remote working and living), EVA operations, mission operations, logistics operations, and science operations that might be required in a deep space context for Near Earth Object (NEO) exploration mission architectures. The 2011 HDU-DSH will be field-tested during the 2011 Desert Research and Technologies Studies (DRaTS) field tests. The HDU project is a "technology-pull" project that integrates technologies and innovations from multiple NASA centers. This project will repurpose the HDU 2010 demo unit that was field tested in the 2010 DRaTS, adding habitation functionality to the prototype unit. This paper will describe the strategy of establishing a multi-center project

  7. A pilot biomedical engineering course in rapid prototyping for mobile health.

    Science.gov (United States)

    Stokes, Todd H; Venugopalan, Janani; Hubbard, Elena N; Wang, May D

    2013-01-01

    Rapid prototyping of medically assistive mobile devices promises to fuel innovation and provides opportunity for hands-on engineering training in biomedical engineering curricula. This paper presents the design and outcomes of a course offered during a 16-week semester in Fall 2011 with 11 students enrolled. The syllabus covered a mobile health design process from end-to-end, including storyboarding, non-functional prototypes, integrated circuit programming, 3D modeling, 3D printing, cloud computing database programming, and developing patient engagement through animated videos describing the benefits of a new device. Most technologies presented in this class are open source and thus provide unlimited "hackability". They are also cost-effective and easily transferrable to other departments.

  8. Using 3D Printing for Rapid Prototyping of Characterization Tools for Investigating Powder Blend Behavior

    DEFF Research Database (Denmark)

    Hirschberg, Cosima; Boetker, Johan P; Rantanen, Jukka

    2018-01-01

    be monitored with an in-line near-infrared (NIR) spectrometer. Calculating the root mean square (RMS) of the scores of the two first principal components of the NIR spectra visualized spectral variation as a function of process time. In a same setup, mechanical properties (basic flow energy) of the powder......There is an increasing need to provide more detailed insight into the behavior of particulate systems. The current powder characterization tools are developed empirically and in many cases, modification of existing equipment is difficult. More flexible tools are needed to provide understanding...... of complex powder behavior, such as mixing process and segregation phenomenon. An approach based on the fast prototyping of new powder handling geometries and interfacing solutions for process analytical tools is reported. This study utilized 3D printing for rapid prototyping of customized geometries...

  9. Rapid and low-cost prototyping of medical devices using 3D printed molds for liquid injection molding.

    Science.gov (United States)

    Chung, Philip; Heller, J Alex; Etemadi, Mozziyar; Ottoson, Paige E; Liu, Jonathan A; Rand, Larry; Roy, Shuvo

    2014-06-27

    Biologically inert elastomers such as silicone are favorable materials for medical device fabrication, but forming and curing these elastomers using traditional liquid injection molding processes can be an expensive process due to tooling and equipment costs. As a result, it has traditionally been impractical to use liquid injection molding for low-cost, rapid prototyping applications. We have devised a method for rapid and low-cost production of liquid elastomer injection molded devices that utilizes fused deposition modeling 3D printers for mold design and a modified desiccator as an injection system. Low costs and rapid turnaround time in this technique lower the barrier to iteratively designing and prototyping complex elastomer devices. Furthermore, CAD models developed in this process can be later adapted for metal mold tooling design, enabling an easy transition to a traditional injection molding process. We have used this technique to manufacture intravaginal probes involving complex geometries, as well as overmolding over metal parts, using tools commonly available within an academic research laboratory. However, this technique can be easily adapted to create liquid injection molded devices for many other applications.

  10. A comparison of different silver inks for printing of conductive tracks on paper substrates for rapid prototyping of electronic circuits

    CSIR Research Space (South Africa)

    Bezuidenhout, PH

    2015-11-01

    Full Text Available of the selection process of different conductive inks for printing onto paper substrates. These results can be utilized in the development process for fully printable rapidly prototyped electronic systems, which can range from environmental sensing solutions...

  11. Rapid prototyping of biodegradable microneedle arrays by integrating CO2 laser processing and polymer molding

    Science.gov (United States)

    Tu, K. T.; Chung, C. K.

    2016-06-01

    An integrated technology of CO2 laser processing and polymer molding has been demonstrated for the rapid prototyping of biodegradable poly-lactic-co-glycolic acid (PLGA) microneedle arrays. Rapid and low-cost CO2 laser processing was used for the fabrication of a high-aspect-ratio microneedle master mold instead of conventional time-consuming and expensive photolithography and etching processes. It is crucial to use flexible polydimethylsiloxane (PDMS) to detach PLGA. However, the direct CO2 laser-ablated PDMS could generate poor surfaces with bulges, scorches, re-solidification and shrinkage. Here, we have combined the polymethyl methacrylate (PMMA) ablation and two-step PDMS casting process to form a PDMS female microneedle mold to eliminate the problem of direct ablation. A self-assembled monolayer polyethylene glycol was coated to prevent stiction between the two PDMS layers during the peeling-off step in the PDMS-to-PDMS replication. Then the PLGA microneedle array was successfully released by bending the second-cast PDMS mold with flexibility and hydrophobic property. The depth of the polymer microneedles can range from hundreds of micrometers to millimeters. It is linked to the PMMA pattern profile and can be adjusted by CO2 laser power and scanning speed. The proposed integration process is maskless, simple and low-cost for rapid prototyping with a reusable mold.

  12. The development of a prototype of a “rapid test” for detection of equine antibodies against tetanus

    OpenAIRE

    Stelzmann, Mareike

    2011-01-01

    the following dissertation, the prototype of a “rapid test” for detection of equine antibodies against tetanus is developed. This test makes it possible to detect antibodies against tetanus in equine serum within one hour. Moreover the prototype allows making a statement about the antibody titer. The standard values of the OIE (WORLD ORGANISATION FOR ANIMAL HEALTH, 2009) to validate in vitro-diagnostical tests for veterinary medicine were followed. The rapid test achieves results comparabl...

  13. Comparison of five-axis milling and rapid prototyping for implant surgical templates.

    Science.gov (United States)

    Park, Ji-Man; Yi, Tae-Kyoung; Koak, Jai-Young; Kim, Seong-Kyoon; Park, Eun-Jin; Heo, Seong-Joo

    2014-01-01

    This study aims to compare and evaluate the accuracy of surgical templates fabricated using coordinate synchronization processing with five-axis milling and design-related processing with rapid prototyping (RP). Master phantoms with 10 embedded gutta-percha cylinders hidden under artificial gingiva were fabricated and imaged using cone beam computed tomography. Vectors of the hidden cylinders were extracted and transferred to those of the planned implants through reverse engineering using virtual planning software. An RP-produced template was fabricated by stereolithography in photopolymer at the RP center according to planned data. Metal sleeves were bonded after holes were bored (group RP). For the milled template, milling coordinates were synchronized using the conversion process for the coordinate synchronization platform located on the model's bottom. Metal bushings were set on holes milled on the five-axis milling machine, on which the model was fixed through the coordinate synchronization plate, and the framework was constructed on the model using orthodontic resin (group CS). A computed tomography image was taken with templates firmly fixed on models using anchor pins (RP) or anchor screws (CS). The accuracy was analyzed via reverse engineering. Differences between the two groups were compared by repeated measures two-factor analysis. From the reverse-engineered image of the template on the experimental model, RP-produced templates showed significantly larger deviations than did milled surgical guides. Maximum deviations of the group RP were 1.58 mm (horizontal), 1.68 mm (vertical), and 8.51 degrees (angular); those of the group CS were 0.68 mm (horizontal), 0.41 mm (vertical), and 3.23 degrees (angular). A comparison of milling and RP template production methods showed that a vector-milled surgical guide had significantly smaller deviations than did an RP-produced template. The accuracy of computer-guided milled surgical templates was within the safety

  14. New technologies applied to surgical processes: Virtual Reality and rapid prototyping.

    Science.gov (United States)

    Suárez-Mejías, Cristina; Gomez-Ciriza, Gorka; Valverde, Israel; Parra Calderón, Carlos; Gómez-Cía, Tomás

    2015-01-01

    AYRA is software of virtual reality for training, planning and optimizing surgical procedures. AYRA was developed under a research, development and innovation project financed by the Andalusian Ministry of Health, called VirSSPA. Nowadays AYRA has been successfully used in more than 1160 real cases and after proving its efficiency it has been introduced in the clinical practice at the Virgen del Rocío University Hospital . Furthermore, AYRA allows generating physical 3D biomodels using rapid prototyping technology. They are used for surgical planning support, intraoperative reference or defect reconstruction. In this paper, some of these tools and some real cases are presented.

  15. Rapid tooling for functional prototyping of metal mold processes: Literature review on cast tooling

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, M.D. [Sandia National Labs., Albuquerque, NM (United States); Hochanadel, P.W. [Colorado School of Mines, Golden, CO (United States). Dept. of Metallurgical and Materials Engineering

    1995-11-01

    This report is a literature review on cast tooling with the general focus on AISI H13 tool steel. The review includes processing of both wrought and cast H13 steel along with the accompanying microstructures. Also included is the incorporation of new rapid prototyping technologies, such as Stereolithography and Selective Laser Sintering, into the investment casting of tool steel. The limiting property of using wrought or cast tool steel for die casting is heat checking. Heat checking is addressed in terms of testing procedures, theories regarding the mechanism, and microstructural aspects related to the cracking.

  16. Rapid prototyping of the Central Safety System for Nuclear Risk in ITER

    Energy Technology Data Exchange (ETDEWEB)

    Scibile, L. [ITER Organization, CS 90 046, St. Paul-lez-Durance, Cedex (France); Ambrosino, G. [Consorzio CREATE, Universita degli Studi di Napoli Federico II, via Claudio 21, 80125, Napoli (Italy); De Tommasi, G., E-mail: detommas@unina.i [Consorzio CREATE, Universita degli Studi di Napoli Federico II, via Claudio 21, 80125, Napoli (Italy); Pironti, A. [Consorzio CREATE, Universita degli Studi di Napoli Federico II, via Claudio 21, 80125, Napoli (Italy)

    2010-07-15

    The Central Safety System for Nuclear Risk (CSS-N) coordinates the safety control systems to ensure nuclear safety for the ITER complex. Since the CSS-N is a safety critical system, its validation and commissioning play a very important role; in particular the required level of reliability must be demonstrated. In such a scenario, it is strongly recommended to use modeling and simulation tools since the early design phase. Indeed, the modeling tools will help in the definition of the control system requirements. Furthermore the models can than be used for the rapid prototyping of the safety system. Hardware-in-the-loop simulations can also be performed in order to assess the performance of the control hardware against a plant simulator. The proposed approach relies on the availability of a plant simulator to develop the prototype of the control system. This paper introduces the methodology used to design and develop both the CSS-N Oriented Plant Simulator and the CSS-N Prototype.

  17. Design and manufacturing of ear prosthesis by means of rapid prototyping technology.

    Science.gov (United States)

    De Crescenzio, F; Fantini, M; Ciocca, L; Persiani, F; Scotti, R

    2011-03-01

    In this paper, the complete procedure to design and construct reusable moulds for implant-based ear prosthesis and manufacture substructures by means of a computer aided design-computer aided manufacturing (CAD-CAM) procedure and rapid prototyping (RP) technology is presented. The scan of the healthy ear, the virtual superimposition of its mirrored image on to the defective side, and the rapid manufacturing of the substructure and of the mould eliminate several steps of traditional procedures (wax, stone, try-in). Moreover, the precise design and customization of the substructure is presented, with the original and engineered shape for the retention of the silicone. The time and cost saving results of this protocol are presented together with a discussion of the main design features that make the prosthesis a stable and reproducible system to improve rehabilitation of patients with auricular defects or absence.

  18. Rapid prototyping of nanotube-based devices using topology-optimized microgrippers

    DEFF Research Database (Denmark)

    Sardan, Özlem; Eichhorn, Volkmar; Petersen, D.H.

    2008-01-01

    Nanorobotic handling of carbon nanotubes (CNTs) using microgrippers is one of the most promising approaches for the rapid characterization of the CNTs and also for the assembly of prototypic nanotube-based devices. In this paper, we present pick-and-place nanomanipulation of multi-walled CNTs...... in a rapid and a reproducible manner. We placed CNTs on copper TEM grids for structural analysis and on AFM probes for the assembly of AFM super-tips. We used electrothermally actuated polysilicon microgrippers designed using topology optimization in the experiments. The microgrippers are able to open...... with an amorphous carbon layer, which is locally removed at the contact points with the microgripper. The assembled AFM super-tips are used for AFM measurements of microstructures with high aspect ratios....

  19. Rapid prototyping of an EEG-based brain-computer interface (BCI).

    Science.gov (United States)

    Guger, C; Schlögl, A; Neuper, C; Walterspacher, D; Strein, T; Pfurtscheller, G

    2001-03-01

    The electroencephalogram (EEG) is modified by motor imagery and can be used by patients with severe motor impairments (e.g., late stage of amyotrophic lateral sclerosis) to communicate with their environment. Such a direct connection between the brain and the computer is known as an EEG-based brain-computer interface (BCI). This paper describes a new type of BCI system that uses rapid prototyping to enable a fast transition of various types of parameter estimation and classification algorithms to real-time implementation and testing. Rapid prototyping is possible by using Matlab, Simulink, and the Real-Time Workshop. It is shown how to automate real-time experiments and perform the interplay between on-line experiments and offline analysis. The system is able to process multiple EEG channels on-line and operates under Windows 95 in real-time on a standard PC without an additional digital signal processor (DSP) board. The BCI can be controlled over the Internet, LAN or modem. This BCI was tested on 3 subjects whose task it was to imagine either left or right hand movement. A classification accuracy between 70% and 95% could be achieved with two EEG channels after some sessions with feedback using an adaptive autoregressive (AAR) model and linear discriminant analysis (LDA).

  20. Replication of human tracheobronchial hollow airway models using a selective laser sintering rapid prototyping technique.

    Science.gov (United States)

    Clinkenbeard, Rodney E; Johnson, David L; Parthasarathy, Ramkumar; Altan, M Cengiz; Tan, Kah-Hoe; Park, Seok-Min; Crawford, Richard H

    2002-01-01

    Exposures to toxic or pathogenic aerosols are known to produce adverse health effects. The nature and severity of these effects often are governed in large part by the location and amount of aerosol deposition within the respiratory tract. Morphologically detailed replica hollow lung airway casts are widely used in aerosol deposition research; however, techniques are not currently available that allow replicate deposition studies in identical morphologically detailed casts produced from a common reference anatomy. This project developed a technique for the precision manufacture of morphologically detailed human tracheobronchial airway models based on high-resolution anatomical imaging data. Detailed physical models were produced using the selective laser sintering (SLS) rapid prototyping process. Input to the SLS process was a three-dimensional computer model developed by boundary-based two-dimension to three-dimension conversion of anatomical images from the original National Institutes of Health/National Library of Medicine Visible Human male data set. The SLS process produced identical replicate models that corresponded exactly to the anatomical section images, within the limits of the measurement. At least five airway generations were achievable, corresponding to airways less than 2 mm in diameter. It is anticipated that rapid prototyping manufacture of respiratory tract structures based on reference anatomies such as the Visible Male and Visible Female may provide "gold standard" models for inhaled aerosol deposition studies. Adaptations of the models to represent various disease states may be readily achieved, thereby promoting exploration of pharmaceutical research on targeted drug delivery via inhaled aerosols.

  1. Rapid prototyping prosthetic hand acting by a low-cost shape-memory-alloy actuator.

    Science.gov (United States)

    Soriano-Heras, Enrique; Blaya-Haro, Fernando; Molino, Carlos; de Agustín Del Burgo, José María

    2018-01-08

    The purpose of this article is to develop a new concept of modular and operative prosthetic hand based on rapid prototyping and a novel shape-memory-alloy (SMA) actuator, thus minimizing the manufacturing costs. An underactuated mechanism was needed for the design of the prosthesis to use only one input source. Taking into account the state of the art, an underactuated mechanism prosthetic hand was chosen so as to implement the modifications required for including the external SMA actuator. A modular design of a new prosthesis was developed which incorporated a novel SMA actuator for the index finger movement. The primary objective of the prosthesis is achieved, obtaining a modular and functional low-cost prosthesis based on additive manufacturing executed by a novel SMA actuator. The external SMA actuator provides a modular system which allows implementing it in different systems. This paper combines rapid prototyping and a novel SMA actuator to develop a new concept of modular and operative low-cost prosthetic hand.

  2. Development of novel hybrid poly(l-lactide)/chitosan scaffolds using the rapid freeze prototyping technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, N; Chen, X B [Division of Biomedical Engineering, University of Saskatchewan, Saskatoon, Saskatchewan (Canada); Li, M G [Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, Saskatchewan (Canada); Cooper, D, E-mail: xbc719@mail.usask.ca [Department of Anatomy and Cell Biology, University of Saskatchewan, Saskatoon, Saskatchewan (Canada)

    2011-09-15

    Engineered scaffolds have been shown to be critical to various tissue engineering applications. This paper presents the development of a novel three-dimensional scaffold made from a mixture of chitosan microspheres (CMs) and poly(l-lactide) by means of the rapid freeze prototyping (RFP) technique. The CMs were used to encapsulate bovine serum albumin (BSA) and improve the scaffold mechanical properties. Experiments to examine the BSA release were carried out; the BSA release could be controlled by adjusting the crosslink degree of the CMs and prolonged after the CMs were embedded into the PLLA scaffolds, while the examination of the mechanical properties of the scaffolds illustrates that they depend on the ratio of CMs to PLLA in the scaffolds as well as the cryogenic temperature used in the RFP fabrication process. The chemical characteristics of the PLLA/chitosan scaffolds were evaluated by Fourier transform infrared (FTIR) spectroscopy. The morphological and pore structure of the scaffolds were also examined by scanning electron microscopy and micro-tomography. The results obtained show that the scaffolds have higher porosity and enhanced pore size distribution compared to those fabricated by the dispensing-based rapid prototyping technique. This study demonstrates that the novel scaffolds have not only enhanced porous structure and mechanical properties but also showed the potential to preserve the bioactivities of the biomolecules and to control the biomolecule distribution and release rate.

  3. The MOLGENIS toolkit: rapid prototyping of biosoftware at the push of a button

    Science.gov (United States)

    2010-01-01

    Background There is a huge demand on bioinformaticians to provide their biologists with user friendly and scalable software infrastructures to capture, exchange, and exploit the unprecedented amounts of new *omics data. We here present MOLGENIS, a generic, open source, software toolkit to quickly produce the bespoke MOLecular GENetics Information Systems needed. Methods The MOLGENIS toolkit provides bioinformaticians with a simple language to model biological data structures and user interfaces. At the push of a button, MOLGENIS’ generator suite automatically translates these models into a feature-rich, ready-to-use web application including database, user interfaces, exchange formats, and scriptable interfaces. Each generator is a template of SQL, JAVA, R, or HTML code that would require much effort to write by hand. This ‘model-driven’ method ensures reuse of best practices and improves quality because the modeling language and generators are shared between all MOLGENIS applications, so that errors are found quickly and improvements are shared easily by a re-generation. A plug-in mechanism ensures that both the generator suite and generated product can be customized just as much as hand-written software. Results In recent years we have successfully evaluated the MOLGENIS toolkit for the rapid prototyping of many types of biomedical applications, including next-generation sequencing, GWAS, QTL, proteomics and biobanking. Writing 500 lines of model XML typically replaces 15,000 lines of hand-written programming code, which allows for quick adaptation if the information system is not yet to the biologist’s satisfaction. Each application generated with MOLGENIS comes with an optimized database back-end, user interfaces for biologists to manage and exploit their data, programming interfaces for bioinformaticians to script analysis tools in R, Java, SOAP, REST/JSON and RDF, a tab-delimited file format to ease upload and exchange of data, and detailed technical

  4. Rapid prototyping of a complex model for the manufacture of plaster molds for slip casting ceramic

    Directory of Open Access Journals (Sweden)

    D. P. C. Velazco

    2014-12-01

    Full Text Available Computer assisted designing (CAD is well known for several decades and employed for ceramic manufacturing almost since the beginning, but usually employed in the first part of the projectual ideation processes, neither in the prototyping nor in the manufacturing stages. The rapid prototyping machines, also known as 3D printers, have the capacity to produce in a few hours real pieces using plastic materials of high resistance, with great precision and similarity with respect to the original, based on unprecedented digital models produced by means of modeling with specific design software or from the digitalization of existing parts using the so-called 3D scanners. The main objective of the work is to develop the methodology used in the entire process of building a part in ceramics from the interrelationship between traditional techniques and new technologies for the manufacture of prototypes. And to take advantage of the benefits that allow us this new reproduction technology. The experience was based on the generation of a complex piece, in digital format, which served as the model. A regular 15 cm icosahedron presented features complex enough not to advise the production of the model by means of the traditional techniques of ceramics (manual or mechanical. From this digital model, a plaster mold was made in the traditional way in order to slip cast clay based slurries, freely dried in air and fired and glazed in the traditional way. This experience has shown the working hypothesis and opens up the possibility of new lines of work to academic and technological levels that will be explored in the near future. This technology provides a wide range of options to address the formal aspect of a part to be performed for the field of design, architecture, industrial design, the traditional pottery, ceramic art, etc., which allow you to amplify the formal possibilities, save time and therefore costs when drafting the necessary and appropriate matrixes

  5. The MOLGENIS toolkit: rapid prototyping of biosoftware at the push of a button.

    Science.gov (United States)

    Swertz, Morris A; Dijkstra, Martijn; Adamusiak, Tomasz; van der Velde, Joeri K; Kanterakis, Alexandros; Roos, Erik T; Lops, Joris; Thorisson, Gudmundur A; Arends, Danny; Byelas, George; Muilu, Juha; Brookes, Anthony J; de Brock, Engbert O; Jansen, Ritsert C; Parkinson, Helen

    2010-12-21

    There is a huge demand on bioinformaticians to provide their biologists with user friendly and scalable software infrastructures to capture, exchange, and exploit the unprecedented amounts of new *omics data. We here present MOLGENIS, a generic, open source, software toolkit to quickly produce the bespoke MOLecular GENetics Information Systems needed. The MOLGENIS toolkit provides bioinformaticians with a simple language to model biological data structures and user interfaces. At the push of a button, MOLGENIS' generator suite automatically translates these models into a feature-rich, ready-to-use web application including database, user interfaces, exchange formats, and scriptable interfaces. Each generator is a template of SQL, JAVA, R, or HTML code that would require much effort to write by hand. This 'model-driven' method ensures reuse of best practices and improves quality because the modeling language and generators are shared between all MOLGENIS applications, so that errors are found quickly and improvements are shared easily by a re-generation. A plug-in mechanism ensures that both the generator suite and generated product can be customized just as much as hand-written software. In recent years we have successfully evaluated the MOLGENIS toolkit for the rapid prototyping of many types of biomedical applications, including next-generation sequencing, GWAS, QTL, proteomics and biobanking. Writing 500 lines of model XML typically replaces 15,000 lines of hand-written programming code, which allows for quick adaptation if the information system is not yet to the biologist's satisfaction. Each application generated with MOLGENIS comes with an optimized database back-end, user interfaces for biologists to manage and exploit their data, programming interfaces for bioinformaticians to script analysis tools in R, Java, SOAP, REST/JSON and RDF, a tab-delimited file format to ease upload and exchange of data, and detailed technical documentation. Existing databases

  6. Rapid prototyping of flexible intrafascicular electrode arrays by picosecond laser structuring

    Science.gov (United States)

    Mueller, Matthias; de la Oliva, Natalia; del Valle, Jaume; Delgado-Martínez, Ignacio; Navarro, Xavier; Stieglitz, Thomas

    2017-12-01

    Objective. Interfacing the peripheral nervous system can be performed with a large variety of electrode arrays. However, stimulating and recording a nerve while having a reasonable amount of channels limits the number of available systems. Translational research towards human clinical trial requires device safety and biocompatibility but would benefit from design flexibility in the development process to individualize probes. Approach. We selected established medical grade implant materials like precious metals and Parylene C to develop a rapid prototyping process for novel intrafascicular electrode arrays using a picosecond laser structuring. A design for a rodent animal model was developed in conjunction with an intrafascicular implantation strategy. Electrode characterization and optimization was performed first in saline solution in vitro before performance and biocompatibility were validated in sciatic nerves of rats in chronic implantation. Main results. The novel fabrication process proved to be suitable for prototyping and building intrafascicular electrode arrays. Electrochemical properties of the electrode sites were enhanced and tested for long-term stability. Chronic implantation in the sciatic nerve of rats showed good biocompatibility, selectivity and stable stimulation thresholds. Significance. Established medical grade materials can be used for intrafascicular nerve electrode arrays when laser structuring defines structure size in the micro-scale. Design flexibility reduces re-design cycle time and material certificates are beneficial support for safety studies on the way to clinical trials.

  7. The application of rapid prototyping to improve bone reconstruction in immediate dentoalveolar restoration: a case report.

    Science.gov (United States)

    Martins da Rosa, José Carlos; Fadanelli, Marcos Alexandre; Zimmerman, Diego; de Oliveira Rosa, Ariádene Cristina Pértile

    This article describes the use of rapid prototyping (RP) for diagnosis, planning, and execution of the reconstruction of hard and soft tissue in socket defects using immediate dentoalveolar restoration (IDR). In cases of tissue loss in anterior dental areas, esthetic rehabilitation poses a major challenge with respect to treatment planning with the goal of long-term tissue maintenance. The IDR technique consists of immediate reconstruction in a single procedure of bone and soft tissue around implants placed immediately after extraction, and prosthetic rehabilitation. As this procedure is immediate and flapless, the correct diagnosis of tissue loss and correct graft adaptation are mandatory. RP can increase the precision of the procedure, as demonstrated using a clinical case characterized by total loss of the buccal bone wall and gingival recession. The results were evaluated by clinical assessment, photography, radiography, cone beam computed tomography (CBCT), and prototyping. The application of RP facilitated the execution of IDR as it enabled more accurate diagnosis of the socket defect and more precise adaptation of the tissue graft. A clinical study should be conducted to evaluate the effects of RP on the clinical results of the IDR technique.

  8. Fabrication of a Cranial Prosthesis Combined with an Ocular Prosthesis Using Rapid Prototyping: A Case Report

    Directory of Open Access Journals (Sweden)

    Gayatri Shankaran

    2016-08-01

    Full Text Available Rapid prototyping (RP is a technique of manufacturing parts by the additive layer manufacturing technology; where, a three-dimensional (3D model created in a computer aided design (CAD system is sectioned into 2D profiles, which are further constructed by RP layer by layer. Its use is not limited to industrial or engineering fields and has extended to the medical field for the manufacturing of custom implants and prostheses, the study of anatomy and surgical planning. Nowadays, dentists are more frequently encountered with the individuals affected with craniofacial defects due to trauma. In such cases, the cranio-maxillofacial rehabilitation is a real challenge to bring the patients back to society and promote their well-being. The conventional impression technique for facial prosthesis fabrication has the disadvantage of deforming the soft tissue and causing discomfort for the patient. Herein, we describe the fabrication of a cranial prosthesis combined with an ocular prosthesis with RP and stereolithography.

  9. Production of new 3D scaffolds for bone tissue regeneration by rapid prototyping.

    Science.gov (United States)

    Fradique, R; Correia, T R; Miguel, S P; de Sá, K D; Figueira, D R; Mendonça, A G; Correia, I J

    2016-04-01

    The incidence of bone disorders, whether due to trauma or pathology, has been trending upward with the aging of the worldwide population. The currently available treatments for bone injuries are rather limited, involving mainly bone grafts and implants. A particularly promising approach for bone regeneration uses rapid prototyping (RP) technologies to produce 3D scaffolds with highly controlled structure and orientation, based on computer-aided design models or medical data. Herein, tricalcium phosphate (TCP)/alginate scaffolds were produced using RP and subsequently their physicochemical, mechanical and biological properties were characterized. The results showed that 60/40 of TCP and alginate formulation was able to match the compression and present a similar Young modulus to that of trabecular bone while presenting an adequate biocompatibility. Moreover, the biomineralization ability, roughness and macro and microporosity of scaffolds allowed cell anchoring and proliferation at their surface, as well as cell migration to its interior, processes that are fundamental for osteointegration and bone regeneration.

  10. Colloidal processing and rapid prototyping of Si{sub 3}N{sub 4}

    Energy Technology Data Exchange (ETDEWEB)

    Liwu Wang

    1998-12-01

    Some progresses have been made in the wet shaping of Si{sub 3}N{sub 4} based on a better understanding of the colloidal behavior of suspensions and by improved pressure casting with porous polystyrene (PS) molds. This work illustrated that the combination of proper colloidal processing and rapid prototyping is an effective way to fabricate high-performance ceramics with complex shapes. In colloidal processing the packing density and microstructure of green bodies can be controlled if the interaction between ceramic particles in suspensions and the conditions under which the suspensions are consolidated are understood. Therefore, detailed studies on the surface chemistry of the Si{sub 3}N{sub 4} powder, the dispersing behavior of Si{sub 3}N{sub 4} suspensions, the influence of dispersants and the mechanism during powder consolidation into complex-shaped green bodies are performed. (orig.)

  11. A frame-based domain-specific language for rapid prototyping of FPGA-based software-defined radios

    Science.gov (United States)

    Ouedraogo, Ganda Stephane; Gautier, Matthieu; Sentieys, Olivier

    2014-12-01

    The field-programmable gate array (FPGA) technology is expected to play a key role in the development of software-defined radio (SDR) platforms. As this technology evolves, low-level designing methods for prototyping FPGA-based applications did not change throughout the decades. In the outstanding context of SDR, it is important to rapidly implement new waveforms to fulfill such a stringent flexibility paradigm. At the current time, different proposals have defined, through software-based approaches, some efficient methods to prototype SDR waveforms in a processor-based running environment. This paper describes a novel design flow for FPGA-based SDR applications. This flow relies upon high-level synthesis (HLS) principles and leverages the nascent HLS tools. Its entry point is a domain-specific language (DSL) which handles the complexity of programming an FPGA and integrates some SDR features so as to enable automatic waveform control generation from a data frame model. Two waveforms (IEEE 802.15.4 and IEEE 802.11a) have been designed and explored via this new methodology, and the results are highlighted in this paper.

  12. Novel CAD/CAM rapid prototyping of next-generation biomedical devices

    Science.gov (United States)

    Doraiswamy, Anand

    An aging population with growing healthcare needs demands multifaceted tools for diagnosis and treatment of health conditions. In the near-future, drug-administration devices, implantable devices/sensors, enhanced prosthesis, artificial and unique functional tissue constructs will become increasingly significant. Conventional technologies for mass-produced implants do not adequately take individual patient anatomy into consideration. Development of novel CAD/CAM rapid prototyping techniques may significantly accelerate progress of these devices for next-generation patient-care. In this dissertation, several novel rapid prototyping techniques have been introduced for next-generation biomedical applications. Two-photon polymerization was developed to microfabricate scaffolds for tissue engineering, microneedles for drug-delivery and ossicular replacement prostheses. Various photoplymers were evaluated for feasibility, mechanical properties, cytotoxicity, and surface properties. Laser direct write using MDW was utilized for developing microstructures of bioceramics such as hydroxyapatite, and viable mammalian osteosarcoma cells. CAD/CAM laser micromachining (CLM) was developed to engineer biointerfaces as surface recognition regions for differential adherence of cells and growth into tissue-like networks. CLM was also developed for engineering multi-cellular vascular networks. Cytotoxic evaluations and growth studies demonstrated VEGF-induced proliferation of HAAE-1 human aortic endothelial cells with inhibition of HA-VSMC human aortic smooth muscle cells. Finally, piiezoelectric inkjet printing was developed for controlled administration of natural and synthetic adhesives to overcome several problems associated with conventional tissue bonding materials, and greatly improve wound-repair in next generation eye repair, fracture fixation, organ fixation, wound closure, tissue engineering, and drug delivery devices.

  13. Technical Note: Rapid prototyping of 3D grid arrays for image guided therapy quality assurance

    Energy Technology Data Exchange (ETDEWEB)

    Kittle, David; Holshouser, Barbara; Slater, James M.; Guenther, Bob D.; Pitsianis, Nikos P.; Pearlstein, Robert D. [Department of Radiation Medicine, Epilepsy Radiosurgery Research Program, Loma Linda University, Loma Linda, California 92354 (United States); Department of Radiology, Loma Linda University Medical Center, Loma Linda, California 92354 (United States); Department of Radiation Medicine, Loma Linda University, Loma Linda, California 92354 (United States); Department of Physics, Duke University, Durham, North Carolina 27708 (United States); Department of Electrical and Computer Engineering and Department of Computer Science, Duke University, Durham, North Carolina 27708 (United States); Department of Radiation Medicine, Epilepsy Radiosurgery Research Program, Loma Linda University, Loma Linda, California 92354 and Department of Surgery-Neurosurgery, Duke University and Medical Center, Durham, North Carolina 27710 (United States)

    2008-12-15

    Three dimensional grid phantoms offer a number of advantages for measuring imaging related spatial inaccuracies for image guided surgery and radiotherapy. The authors examined the use of rapid prototyping technology for directly fabricating 3D grid phantoms from CAD drawings. We tested three different fabrication process materials, photopolymer jet with acrylic resin (PJ/AR), selective laser sintering with polyamide (SLS/P), and fused deposition modeling with acrylonitrile butadiene styrene (FDM/ABS). The test objects consisted of rectangular arrays of control points formed by the intersections of posts and struts (2 mm rectangular cross section) and spaced 8 mm apart in the x, y, and z directions. The PJ/AR phantom expanded after immersion in water which resulted in permanent warping of the structure. The surface of the FDM/ABS grid exhibited a regular pattern of depressions and ridges from the extrusion process. SLS/P showed the best combination of build accuracy, surface finish, and stability. Based on these findings, a grid phantom for assessing machine-dependent and frame-induced MR spatial distortions was fabricated to be used for quality assurance in stereotactic neurosurgical and radiotherapy procedures. The spatial uniformity of the SLS/P grid control point array was determined by CT imaging (0.6x0.6x0.625 mm{sup 3} resolution) and found suitable for the application, with over 97.5% of the control points located within 0.3 mm of the position specified in CAD drawing and none of the points off by more than 0.4 mm. Rapid prototyping is a flexible and cost effective alternative for development of customized grid phantoms for medical physics quality assurance.

  14. Rapid methods for detection of bacteria

    DEFF Research Database (Denmark)

    Corfitzen, Charlotte B.; Andersen, B.Ø.; Miller, M.

    2006-01-01

    Traditional methods for detection of bacteria in drinking water e.g. Heterotrophic Plate Counts (HPC) or Most Probable Number (MNP) take 48-72 hours to give the result. New rapid methods for detection of bacteria are needed to protect the consumers against contaminations. Two rapid methods...

  15. Preoperative planning of thoracic surgery with use of three-dimensional reconstruction, rapid prototyping, simulation and virtual navigation.

    Science.gov (United States)

    Heuts, Samuel; Sardari Nia, Peyman; Maessen, Jos G

    2016-01-01

    For the past decades, surgeries have become more complex, due to the increasing age of the patient population referred for thoracic surgery, more complex pathology and the emergence of minimally invasive thoracic surgery. Together with the early detection of thoracic disease as a result of innovations in diagnostic possibilities and the paradigm shift to personalized medicine, preoperative planning is becoming an indispensable and crucial aspect of surgery. Several new techniques facilitating this paradigm shift have emerged. Pre-operative marking and staining of lesions are already a widely accepted method of preoperative planning in thoracic surgery. However, three-dimensional (3D) image reconstructions, virtual simulation and rapid prototyping (RP) are still in development phase. These new techniques are expected to become an important part of the standard work-up of patients undergoing thoracic surgery in the future. This review aims at graphically presenting and summarizing these new diagnostic and therapeutic tools.

  16. A digital approach for design and fabrication by rapid prototyping of orthosis for developmental dysplasia of the hip

    Directory of Open Access Journals (Sweden)

    Rodrigo Munhoz

    Full Text Available Abstract Introduction Immobilization in a hip spica cast is required in surgical and nonsurgical treatments for children aged three months to four years diagnosed with developmental dysplasia of the hip. Skin complications are associated with the use of the spica cast in 30% of the cases. This research explores the use of photogrammetry and rapid prototyping for the production of a lighter, shower friendly and hygienic hip orthosis that could replace the hip spica cast. Methods Digitalized data of a plastic dool was used for design and fabrication of a customised hip orthosis following four steps: 1 Digitalization of the external anatomical structure by photogrammetry using a smartphone and open source software; 2 Idealization and 3D modeling of the hip orthosis; 3 Rapid prototyping of a low cost orthosis in polymer polylact acid; 4 Evaluation tests. Results Photogrammetry provided a good 3D reconstruction of the dool's hip and legs. The manufacture method to produce the hip orthosis was accurate in fitting the hip orthosis to the contours of the doll. The orthosis could be easily placed on the doll ensuring mechanical strength to immobilize the region of the hip. Conclusion A new approach and the feasibility of both techniques for hip orthosis fabrication were described. It represents an exciting advance for the development of hip orthosis that could be used in orthopedics. To test the effectiveness of this orthosis for developmental dysplasia of the hip treatment in newborns, material and mechanical tests, design optimization and physical tests with patients should be carried.

  17. Pulseq: A rapid and hardware-independent pulse sequence prototyping framework.

    Science.gov (United States)

    Layton, Kelvin J; Kroboth, Stefan; Jia, Feng; Littin, Sebastian; Yu, Huijun; Leupold, Jochen; Nielsen, Jon-Fredrik; Stöcker, Tony; Zaitsev, Maxim

    2017-04-01

    Implementing new magnetic resonance experiments, or sequences, often involves extensive programming on vendor-specific platforms, which can be time consuming and costly. This situation is exacerbated when research sequences need to be implemented on several platforms simultaneously, for example, at different field strengths. This work presents an alternative programming environment that is hardware-independent, open-source, and promotes rapid sequence prototyping. A novel file format is described to efficiently store the hardware events and timing information required for an MR pulse sequence. Platform-dependent interpreter modules convert the file to appropriate instructions to run the sequence on MR hardware. Sequences can be designed in high-level languages, such as MATLAB, or with a graphical interface. Spin physics simulation tools are incorporated into the framework, allowing for comparison between real and virtual experiments. Minimal effort is required to implement relatively advanced sequences using the tools provided. Sequences are executed on three different MR platforms, demonstrating the flexibility of the approach. A high-level, flexible and hardware-independent approach to sequence programming is ideal for the rapid development of new sequences. The framework is currently not suitable for large patient studies or routine scanning although this would be possible with deeper integration into existing workflows. Magn Reson Med 77:1544-1552, 2017. © 2016 International Society for Magnetic Resonance in Medicine. © 2016 International Society for Magnetic Resonance in Medicine.

  18. Rapid Prototyping of the Central Safety System for Nuclear Risk in ITER

    Energy Technology Data Exchange (ETDEWEB)

    Scibile, L. [ITER Organization, 13 - St. Paul lez Durance (France); Ambrosino, G.; De Tommasi, G.; Pironti, A. [Euratom-ENEA-CREATE, Universita di Napoli Federico II, Napoli (Italy)

    2009-07-01

    Full text of publication follows: In the current ITER Baseline design, the Central Safety System for Nuclear Risk (CSS-N) is the safety control system in charge to assure nuclear safety for the plant, personnel and environment. In particular it is envisaged that the CSS shall interface to the plant safety systems for nuclear risk and shall coordinate the individual protection provided by the intervention of these systems by the activation, where required, of additional protections. The design of such a system, together with its implementation, strongly depends on the requirements, particularly in terms of reliability. The CSS-N is a safety critical system, thus its validation and commissioning play a very important role, since the required level of reliability must be demonstrated. In such a scenario, where a new and non-conventional system has to be deployed, it is strongly recommended to use modeling and simulation tools since the early design phase. Indeed, the modeling tools will help in the definition of the system requirements, and they will be used to test and validate the control logic. Furthermore these tools can be used to rapid design the safety system and to carry out hardware-in-the-loop (HIL) simulations, which permit to assess the performance of the control hardware against a plant simulator. Both a control system prototype and a safety system oriented plant simulator have been developed to assess first the requirements and then the performance of the CSS-N. In particular the presented SW/HW framework permits to design and verify the CSS protection logics and to test and validate these logics by means of HIL simulations. This work introduces both the prototype and plant simulator architectures, together with the methodology adopted to design and implement these validation tools. (authors)

  19. Innovative rapid construction/reconstruction methods.

    Science.gov (United States)

    2005-07-01

    Innovative construction and reconstruction methods provide the opportunity to significantly reduce the time of roadway projects while maintaining the necessary quality of workmanship. The need for these rapid methods stems from the increase in ...

  20. Porous Ti6Al4V scaffold directly fabricating by rapid prototyping: preparation and in vitro experiment

    NARCIS (Netherlands)

    Li Jiaping, L.; de Wijn, J.R.; van Blitterswijk, Clemens; de Groot, K.

    2006-01-01

    Three-dimensional (3D) fiber deposition (3DF), a rapid prototyping technology, was successfully directly applied to produce novel 3D porous Ti6Al4V scaffolds with fully interconnected porous networks and highly controllable porosity and pore size. A key feature of this technology is the 3D

  1. Development of Rapid, Continuous Calibration Techniques and Implementation as a Prototype System for Civil Engineering Materials Evaluation

    Science.gov (United States)

    Scott, M. L.; Gagarin, N.; Mekemson, J. R.; Chintakunta, S. R.

    2011-06-01

    Until recently, civil engineering material calibration data could only be obtained from material sample cores or via time consuming, stationary calibration measurements in a limited number of locations. Calibration data are used to determine material propagation velocities of electromagnetic waves in test materials for use in layer thickness measurements and subsurface imaging. Limitations these calibration methods impose have been a significant impediment to broader use of nondestructive evaluation methods such as ground-penetrating radar (GPR). In 2006, a new rapid, continuous calibration approach was designed using simulation software to address these measurement limitations during a Federal Highway Administration (FHWA) research and development effort. This continuous calibration method combines a digitally-synthesized step-frequency (SF)-GPR array and a data collection protocol sequence for the common midpoint (CMP) method. Modeling and laboratory test results for various data collection protocols and materials are presented in this paper. The continuous-CMP concept was finally implemented for FHWA in a prototype demonstration system called the Advanced Pavement Evaluation (APE) system in 2009. Data from the continuous-CMP protocol is processed using a semblance/coherency analysis to determine material propagation velocities. Continuously calibrated pavement thicknesses measured with the APE system in 2009 are presented. This method is efficient, accurate, and cost-effective.

  2. Planar array stack design aided by rapid prototyping in development of air-breathing PEMFC

    Science.gov (United States)

    Chen, Chen-Yu; Lai, Wei-Hsiang; Weng, Biing-Jyh; Chuang, Huey-Jan; Hsieh, Ching-Yuan; Kung, Chien-Chih

    The polymer electrolyte membrane fuel cell (PEMFC) is one of the most important research topics in the new and clean energy area. The middle or high power PEMFCs can be applied to the transportation or the distributed power system. But for the small power application, it is needed to match the power requirement of the product generally. On the other hand, the direct methanol fuel cell (DMFC) is one of the most common type that researchers are interested in, but recently the miniature or the micro-PEMFCs attract more attention due to their advantages of high open circuit voltage and high power density. The objective of this study is to develop a new air-breathing planar array fuel cell stacked from 10 cells made by rapid prototyping technology which has potential for fast commercial design, low cost manufacturing, and even without converters/inverters for the system. In this paper, the main material of flow field plates is acrylonitrile-butadiene-styrene (ABS) which allows the fuel cell be mass-manufactured by plastic injection molding technology. The rapid prototyping technology is applied to construct the prototype and verify the practicability of the proposed stack design. A 10-cell air-breathing miniature PEMFC stack with a volume of 6 cm × 6 cm × 0.9 cm is developed and tested. Its segmented membrane electrode assembly (MEA) is designed with the active surface area of 1.3 cm × 1.3 cm in each individual MEA. The platinum loading at anode and cathode are 0.2 mg cm -2 and 0.4 mg cm -2, respectively. Results show that the peak power densities of the parallel connected and serial connected stack are 99 mW cm -2 at 0.425 V and 92 mW cm -2 at 4.25 V, respectively under the conditions of 70 °C relative saturated humidity (i.e., dew point temperature), ambient temperature and free convection air. Besides, the stack performance is increased under forced convection. If the cell surface air is blown by an electric fan, the peak power densities of parallel connected and

  3. Planar array stack design aided by rapid prototyping in development of air-breathing PEMFC

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Chen-Yu.; Lai, Wei-Hsiang [Institute of Aeronautics and Astronautics, National Cheng Kung University, No.1, Ta-Hsueh Road, Tainan 701 (China); Weng, Biing-Jyh; Chuang, Huey-Jan; Hsieh, Ching-Yuan; Kung, Chien-Chih [Chung-Shan Institute of Science and Technology, Materials and Electro-Optics Research Division, P.O. Box No. 90008-8-3 Lung-Tan, Tao-Yuan 325 (China)

    2008-04-15

    The polymer electrolyte membrane fuel cell (PEMFC) is one of the most important research topics in the new and clean energy area. The middle or high power PEMFCs can be applied to the transportation or the distributed power system. But for the small power application, it is needed to match the power requirement of the product generally. On the other hand, the direct methanol fuel cell (DMFC) is one of the most common type that researchers are interested in, but recently the miniature or the micro-PEMFCs attract more attention due to their advantages of high open circuit voltage and high power density. The objective of this study is to develop a new air-breathing planar array fuel cell stacked from 10 cells made by rapid prototyping technology which has potential for fast commercial design, low cost manufacturing, and even without converters/inverters for the system. In this paper, the main material of flow field plates is acrylonitrile-butadiene-styrene (ABS) which allows the fuel cell be mass-manufactured by plastic injection molding technology. The rapid prototyping technology is applied to construct the prototype and verify the practicability of the proposed stack design. A 10-cell air-breathing miniature PEMFC stack with a volume of 6 cm x 6 cm x 0.9 cm is developed and tested. Its segmented membrane electrode assembly (MEA) is designed with the active surface area of 1.3 cm x 1.3 cm in each individual MEA. The platinum loading at anode and cathode are 0.2 mg cm{sup -2} and 0.4 mg cm{sup -2}, respectively. Results show that the peak power densities of the parallel connected and serial connected stack are 99 mW cm{sup -2} at 0.425 V and 92 mW cm{sup -2} at 4.25 V, respectively under the conditions of 70 C relative saturated humidity (i.e., dew point temperature), ambient temperature and free convection air. Besides, the stack performance is increased under forced convection. If the cell surface air is blown by an electric fan, the peak power densities of

  4. PROTOTYPE OF VEHICLES POTHOLES DETECTION BASED BLOB DETECTION METHOD

    OpenAIRE

    Djamaluddin, Dewiani

    2017-01-01

    Potholes on road causes majority of traffic incidents. It happens with driver???s unawareness to potholes on the road, while potholes location data mining is still performed manually by technician nowadays. This issues drives these following research and prototyping to be performed. This paper presents a prototype of a pothole detection system using image processing. The system will detect the potholes by assuming potholes as a blob, using blob detection. Live feed from a camera module will b...

  5. Prototyping method for Bragg-type atom interferometers

    Energy Technology Data Exchange (ETDEWEB)

    Benton, Brandon; Krygier, Michael; Heward, Jeffrey; Edwards, Mark [Department of Physics, Georgia Southern University, Statesboro, Georgia 30460-8031 (United States); Clark, Charles W. [Joint Quantum Insitute, National Institute of Standards and Technology and the University of Maryland, Gaithersburg, Maryland 20899 (United States)

    2011-10-15

    We present a method for rapid modeling of new Bragg ultracold atom-interferometer (AI) designs useful for assessing the performance of such interferometers. The method simulates the overall effect on the condensate wave function in a given AI design using two separate elements. These are (1) modeling the effect of a Bragg pulse on the wave function and (2) approximating the evolution of the wave function during the intervals between the pulses. The actual sequence of these pulses and intervals is then followed to determine the approximate final wave function from which the interference pattern can be calculated. The exact evolution between pulses is assumed to be governed by the Gross-Pitaevskii (GP) equation whose solution is approximated using a Lagrangian variational method to facilitate rapid estimation of performance. The method presented here is an extension of an earlier one that was used to analyze the results of an experiment [J. E. Simsarian et al., Phys. Rev. Lett. 85, 2040 (2000)], where the phase of a Bose-Einstein condensate was measured using a Mach-Zehnder-type Bragg AI. We have developed both 1D and 3D versions of this method and we have determined their validity by comparing their predicted interference patterns with those obtained by numerical integration of the 1D GP equation and with the results of the above experiment. We find excellent agreement between the 1D interference patterns predicted by this method and those found by the GP equation. We show that we can reproduce all of the results of that experiment without recourse to an ad hoc velocity-kick correction needed by the earlier method, including some experimental results that the earlier model did not predict. We also found that this method provides estimates of 1D interference patterns at least four orders-of-magnitude faster than direct numerical solution of the 1D GP equation.

  6. Porous titanium scaffolds fabricated using a rapid prototyping and powder metallurgy technique.

    Science.gov (United States)

    Ryan, Garrett E; Pandit, Abhay S; Apatsidis, Dimitrios P

    2008-09-01

    One of the main issues in orthopaedic implant design is the fabrication of scaffolds that closely mimic the biomechanical properties of the surrounding bone. This research reports on a multi-stage rapid prototyping technique that was successfully developed to produce porous titanium scaffolds with fully interconnected pore networks and reproducible porosity and pore size. The scaffolds' porous characteristics were governed by a sacrificial wax template, fabricated using a commercial 3D-printer. Powder metallurgy processes were employed to generate the titanium scaffolds by filling around the wax template with titanium slurry. In the attempt to optimise the powder metallurgy technique, variations in slurry concentration, compaction pressure and sintering temperature were investigated. By altering the wax design template, pore sizes ranging from 200 to 400 microm were achieved. Scaffolds with porosities of 66.8 +/- 3.6% revealed compression strengths of 104.4+/-22.5 MPa in the axial direction and 23.5 +/- 9.6 MPa in the transverse direction demonstrating their anisotropic nature. Scaffold topography was characterised using scanning electron microscopy and microcomputed tomography. Three-dimensional reconstruction enabled the main architectural parameters such as pore size, interconnecting porosity, level of anisotropy and level of structural disorder to be determined. The titanium scaffolds were compared to their intended designs, as governed by their sacrificial wax templates. Although discrepancies in architectural parameters existed between the intended and the actual scaffolds, overall the results indicate that the porous titanium scaffolds have the properties to be potentially employed in orthopaedic applications.

  7. Efficacy and accuracy of a novel rapid prototyping drill template for cervical pedicle screw placement.

    Science.gov (United States)

    Lu, Sheng; Xu, Yong Q; Chen, Guo P; Zhang, Yuan Z; Lu, Di; Chen, Yu B; Shi, Ji H; Xu, Xing M

    2011-01-01

    To develop and validate the efficacy and accuracy of a novel drill template for cervical pedicle instrumentation. A CT scan of the cervical vertebrae was performed, and a 3D model of the vertebrae was reconstructed using MIMICS 10.01 software. The 3D vertebral model was then exported in STL format, and opened in a workstation running UGS Imageware 12.0 software to determine the optimal pedicle screw size and orientation. A virtual navigational template was established according to the laminar anatomic trait, and physical navigational templates were manufactured using rapid prototyping. The navigational templates were used intraoperatively to assist in the placement of cervical pedicle screws. In all, 84 pedicle screws were placed, and the accuracy of screw placement was confirmed with postoperative X-rays and CT scans. Eighty-two screws were rated as Grade 0, 2 as Grade 1, and no screws as Grade 2 or 3. Hence, safer screw positioning was accomplished with the drill template technique. This study demonstrates a patient-specific template technique that is easy to use, can simplify the surgical act, and generates highly accurate cervical pedicle screw placement. The advantages of this technology over traditional techniques are that it enables planning of the screw trajectory to be completed prior to surgery, and that the screw can be sized to fit the patient's anatomy.

  8. Rapid prototyping and evaluation of programmable SIMD SDR processors in LISA

    Science.gov (United States)

    Chen, Ting; Liu, Hengzhu; Zhang, Botao; Liu, Dongpei

    2013-03-01

    With the development of international wireless communication standards, there is an increase in computational requirement for baseband signal processors. Time-to-market pressure makes it impossible to completely redesign new processors for the evolving standards. Due to its high flexibility and low power, software defined radio (SDR) digital signal processors have been proposed as promising technology to replace traditional ASIC and FPGA fashions. In addition, there are large numbers of parallel data processed in computation-intensive functions, which fosters the development of single instruction multiple data (SIMD) architecture in SDR platform. So a new way must be found to prototype the SDR processors efficiently. In this paper we present a bit-and-cycle accurate model of programmable SIMD SDR processors in a machine description language LISA. LISA is a language for instruction set architecture which can gain rapid model at architectural level. In order to evaluate the availability of our proposed processor, three common baseband functions, FFT, FIR digital filter and matrix multiplication have been mapped on the SDR platform. Analytical results showed that the SDR processor achieved the maximum of 47.1% performance boost relative to the opponent processor.

  9. Rapid-prototype endoprosthesis for palliative reconstruction of an upper extremity after resection of bone metastasis.

    Science.gov (United States)

    Pruksakorn, Dumnoensun; Chantarapanich, Nattapon; Arpornchayanon, Olarn; Leerapun, Taninit; Sitthiseripratip, Kriskrai; Vatanapatimakul, Natapoom

    2015-03-01

    To present a rapid-prototype (RP) endoprosthesis replacement after tumor resection in patients with bone metastasis of the upper extremity. The short-term complications and functional outcomes were evaluated as well as the survival of patients and endoprosthesis. Bone metastasis patients who required bone resection and endoprosthesis replacement were enrolled and consented before operation. Custom-made endoprosthesis was fabricated from polymethyl methacrylate assisted by RP technology. After surgery was performed, patients were followed up daily until discharge and monthly until 6 months postoperatively for immediate post-operative complications and for signs of endoprosthesis failure. The functional outcome was evaluated 6 months postoperatively by the Musculoskeletal Tumor Society score (MTSS) and the Mankin score. Thereafter, patients' survival and arm condition were monitored every 3 months. Sixteen cases participated on this study. There were nine proximal-, four total- and two distal humerus, and one proximal ulna replacement. The median follow-up period was 486 days. The mean MTSS was 55 % and the Mankin score was good in 64 % and fair in 36 % of the patients. Glenohumeral subluxation was observed in 23 % of the patients; however, a stable shoulder was achieved in all cases. There were no prosthesis failure or systemic breakage. An RP endoprosthesis may have significant advantages when the entire humerus needs to be replaced, or periarticular sites are involved. This technique offers custom-made endoprosthesis with enough durability, and in a relatively short production time at reasonable costs which are suitable for palliative reconstruction.

  10. New Design for Rapid Prototyping of Digital Master Casts for Multiple Dental Implant Restorations.

    Directory of Open Access Journals (Sweden)

    Luis Romero

    Full Text Available This study proposes the replacement of all the physical devices used in the manufacturing of conventional prostheses through the use of digital tools, such as 3D scanners, CAD design software, 3D implants files, rapid prototyping machines or reverse engineering software, in order to develop laboratory work models from which to finish coatings for dental prostheses. Different types of dental prosthetic structures are used, which were adjusted by a non-rotatory threaded fixing system.From a digital process, the relative positions of dental implants, soft tissue and adjacent teeth of edentulous or partially edentulous patients has been captured, and a maser working model which accurately replicates data relating to the patients oral cavity has been through treatment of three-dimensional digital data.Compared with the conventional master cast, the results show a significant cost savings in attachments, as well as an increase in the quality of reproduction and accuracy of the master cast, with the consequent reduction in the number of patient consultation visits. The combination of software and hardware three-dimensional tools allows the optimization of the planning of dental implant-supported rehabilitations protocol, improving the predictability of clinical treatments and the production cost savings of master casts for restorations upon implants.

  11. Rapid Prototyping of a High Sensitivity Graphene Based Glucose Sensor Strip.

    Directory of Open Access Journals (Sweden)

    Farshad Tehrani

    Full Text Available A rapid prototyping of an inexpensive, disposable graphene and copper nanocomposite sensor strip using polymeric flexible substrate for highly sensitive and selective nonenzymatic glucose detection has been developed and tested for direct oxidization of glucose. The CuNPs were electrochemically deposited on to the graphene sheets to improve electron transfer rates and to enhance electrocatalytic activity toward glucose. The graphene based electrode with CuNPs demonstrated a high degree of sensitivity (1101.3 ± 56 μA/mM.cm2, excellent selectivity (without an interference with Ascorbic Acid, Uric Acid, Dopamine, and Acetaminophen, good stability with a linear response to glucose ranging from 0.1 mM to 0.6 mM concentration, and detection limits of 0.025 mM to 0.9 mM. Characterization of the electrodes was performed by scanning electron microscopy (FESEM and SEM. The electrochemical properties of the modified graphene electrodes were inspected by cyclic voltammetry (CV, electrochemical impedance spectroscopy (EIS, and amperometry.

  12. Rapid Prototyping of a High Sensitivity Graphene Based Glucose Sensor Strip.

    Science.gov (United States)

    Tehrani, Farshad; Reiner, Lisa; Bavarian, Behzad

    2015-01-01

    A rapid prototyping of an inexpensive, disposable graphene and copper nanocomposite sensor strip using polymeric flexible substrate for highly sensitive and selective nonenzymatic glucose detection has been developed and tested for direct oxidization of glucose. The CuNPs were electrochemically deposited on to the graphene sheets to improve electron transfer rates and to enhance electrocatalytic activity toward glucose. The graphene based electrode with CuNPs demonstrated a high degree of sensitivity (1101.3 ± 56 μA/mM.cm2), excellent selectivity (without an interference with Ascorbic Acid, Uric Acid, Dopamine, and Acetaminophen), good stability with a linear response to glucose ranging from 0.1 mM to 0.6 mM concentration, and detection limits of 0.025 mM to 0.9 mM. Characterization of the electrodes was performed by scanning electron microscopy (FESEM and SEM). The electrochemical properties of the modified graphene electrodes were inspected by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and amperometry.

  13. Rapid prototyping of reflectors for vehicle lighting using laser activated remote phosphor

    Science.gov (United States)

    Lachmayer, Roland; Kloppenburg, Gerolf; Wolf, Alexander

    2015-03-01

    Bright white light sources are of significant importance for automotive front lighting systems. Today's upper class vehicles mainly use HID or LED as light source. As a further step in this development laser diode based systems offer high luminance, efficiency and allow the realization of new styling concepts and new dynamic lighting functions. These white laser diode systems can either be realized by mixing different spectral sources or by combining diodes with specific phosphors. Based on the approach of generating light using a laser and remote phosphor, lighting modules are manufactured. Four blue laser diodes (450 nm) are used to activate a phosphor coating and thus to achieve white light. A segmented paraboloid reflector generates the desired light distribution for an additional car headlamp. We use high speed milling and selective laser melting to build the reflector system for this lighting module. We compare the spectral reflection grade of these materials. Furthermore the generated modules are analyzed regarding their efficiency and light distribution. The use of Rapid Prototyping technologies allows an early validation of the chosen concept and is supposed to reduce cost and time in the product development process significantly. Therefor we discuss costs and times of the applied manufacturing technologies.

  14. Rapid prototyping of multi-scale biomedical microdevices by combining additive manufacturing technologies.

    Science.gov (United States)

    Hengsbach, Stefan; Lantada, Andrés Díaz

    2014-08-01

    The possibility of designing and manufacturing biomedical microdevices with multiple length-scale geometries can help to promote special interactions both with their environment and with surrounding biological systems. These interactions aim to enhance biocompatibility and overall performance by using biomimetic approaches. In this paper, we present a design and manufacturing procedure for obtaining multi-scale biomedical microsystems based on the combination of two additive manufacturing processes: a conventional laser writer to manufacture the overall device structure, and a direct-laser writer based on two-photon polymerization to yield finer details. The process excels for its versatility, accuracy and manufacturing speed and allows for the manufacture of microsystems and implants with overall sizes up to several millimeters and with details down to sub-micrometric structures. As an application example we have focused on manufacturing a biomedical microsystem to analyze the impact of microtextured surfaces on cell motility. This process yielded a relevant increase in precision and manufacturing speed when compared with more conventional rapid prototyping procedures.

  15. Virtual Simulator for Autonomous Mobile Robots Navigation System Using Concepts of Control Rapid Prototyping

    Directory of Open Access Journals (Sweden)

    Leonimer Flavio de Melo

    2013-09-01

    Full Text Available This work presents the proposal of virtual environment implementation for project simulation and conception of supervision and control systems for mobile robots, that are capable to operate and adapting in different environments and conditions. This virtual system has as purpose to facilitate the development of embedded architecture systems, emphasizing the implementation of tools that allow the simulation of the kinematic conditions, dynamic and control, with real time monitoring of all important system points. For this, open control architecture is proposal, integrating the two main techniques of robotic control implementation in the hardware level: systems microprocessors and reconfigurable hardware devices. The implemented simulator system is composed of a trajectory generating module, a kinematic and dynamic simulator module and of a analysis module of results and errors. The kinematic and dynamic simulator module makes all simulation of the mobile robot following the pre-determined trajectory of the trajectory generator. All the kinematic and dynamic results shown during the simulation can be evaluated and visualized in graphs and tables formats, in the results analysis module, allowing an improvement in the system, minimizing the errors with the necessary adjustments optimization. For controller implementation in the embedded system, it uses the rapid prototyping, which is the technology that allows, in set with the virtual simulation environment, the development of a controller project for mobile robots. The validation and tests had been accomplishing with nonholonomics mobile robots models with differential transmission.

  16. A rapid, maskless 3D prototyping for fabrication of capillary circuits: Toward urinary protein detection.

    Science.gov (United States)

    Yan, Sheng; Zhu, Yuanqing; Tang, Shi-Yang; Li, Yuxing; Zhao, Qianbin; Yuan, Dan; Yun, Guolin; Zhang, Jun; Zhang, Shiwu; Li, Weihua

    2018-01-02

    Proteinuria is an established risk marker for progressive renal function loss and patients would significantly benefit from a point-of-care testing. Although extensive work has been done to develop the microfluidic devices for the detection of urinary protein, they need the complicated operation and bulky peripherals. Here, we present a rapid, maskless 3D prototyping for fabrication of capillary fluidic circuits using laser engraving. The capillary circuits can be fabricated in a short amount of time (<10 min) without the requirements of clean-room facilities and photomasks. The advanced capillary components (e.g., trigger valves, retention valves and retention bursting valves) were fabricated, enabling the sequential liquid delivery and sample-reagent mixing. With the integration of smartphone-based detection platform, the microfluidic device can quantify the urinary protein via a colorimetric analysis. By eliminating the bulky and expensive equipment, this smartphone-based detection platform is portable for on-site quantitative detection. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Low-Cost Rotating Experimentation in Compressor Aerodynamics Using Rapid Prototyping

    Directory of Open Access Journals (Sweden)

    Mathias Michaud

    2016-01-01

    Full Text Available With the rapid evolution of additive manufacturing, 3D printed parts are no longer limited to display purposes but can also be used in structural applications. The objective of this paper is to show that 3D prototyping can be used to produce low-cost rotating turbomachinery rigs capable of carrying out detailed flow measurements that can be used, among other things, for computational fluid dynamics (CFD code validation. A fully instrumented polymer two-stage axial-mixed flow compressor test rig was designed and fabricated with stereolithography (SLA technology by a team of undergraduate students as part of a senior-year design course. Experiments were subsequently performed on this rig to obtain both the overall pressure rise characteristics of the compressor and the stagnation pressure distributions downstream of the blade rows for comparison with CFD simulations. In doing so, this work provides a first-of-a-kind assessment of the use of polymer additive technology for low-cost rotating turbomachinery experimentation with detailed measurements.

  18. Rapid Prototyping of a Cyclic Olefin Copolymer Microfluidic Device for Automated Oocyte Culturing.

    Science.gov (United States)

    Berenguel-Alonso, Miguel; Sabés-Alsina, Maria; Morató, Roser; Ymbern, Oriol; Rodríguez-Vázquez, Laura; Talló-Parra, Oriol; Alonso-Chamarro, Julián; Puyol, Mar; López-Béjar, Manel

    2017-10-01

    Assisted reproductive technology (ART) can benefit from the features of microfluidic technologies, such as the automation of time-consuming labor-intensive procedures, the possibility to mimic in vivo environments, and the miniaturization of the required equipment. To date, most of the proposed approaches are based on polydimethylsiloxane (PDMS) as platform substrate material due to its widespread use in academia, despite certain disadvantages, such as the elevated cost of mass production. Herein, we present a rapid fabrication process for a cyclic olefin copolymer (COC) monolithic microfluidic device combining hot embossing-using a low-temperature cofired ceramic (LTCC) master-and micromilling. The microfluidic device was suitable for trapping and maturation of bovine oocytes, which were further studied to determine their ability to be fertilized. Furthermore, another COC microfluidic device was fabricated to store sperm and assess its quality parameters over time. The study herein presented demonstrates a good biocompatibility of the COC when working with gametes, and it exhibits certain advantages, such as the nonabsorption of small molecules, gas impermeability, and low fabrication costs, all at the prototyping and mass production scale, thus taking a step further toward fully automated microfluidic devices in ART.

  19. Deep proton writing with 12 MeV protons for rapid prototyping of microstructures in polymethylmethacrylate

    Science.gov (United States)

    Ebraert, Evert; Gökçe, Berkcan; Van Vlierberghe, Sandra; Vervaeke, Michael; Meyer, Pascal; Guttmann, Markus; Dubruel, Peter; Thienpont, Hugo; Van Erps, Jürgen

    2016-10-01

    Deep proton writing (DPW) is a fabrication technology developed for the rapid prototyping of polymer microstructures. We use polymethylmethacrylate (PMMA) substrates, which act as a positive resist, for irradiation with a collimated 12-MeV energy proton beam. Using 12 MeV enables the irradiation of increasingly thick PMMA substrates with less conicity of the sidewalls compared to the lower energies used in previous work. A microhole of 47.7 μm diameter over a depth of 1 mm is achieved, leading to a maximum aspect ratio of 21∶1. The sidewalls of the irradiated structures show a slightly conical shape and their root-mean-square surface roughness is lower than 50 nm averaged over 72 measured areas of 56 μm×44 μm. This means that DPW components have optical surface quality sidewalls for wavelengths larger than 400 nm. Based on the trade-off among the sidewall roughness, conicity, and the development time, we determine that the optimal proton fluence for 12-MeV DPW in PMMA is 7.75×106 μm-2. Finally, we discuss some high aspect ratio microstructures with optical surface quality that were created with DPW to be used for a myriad of applications, such as micromirrors, microlenses, optofluidic devices, and high-precision alignment structures for single-mode optical fiber connectors.

  20. Scaffolds with a standardized macro-architecture fabricated from several calcium phosphate ceramics using an indirect rapid prototyping technique

    Science.gov (United States)

    Wilson, C. E.; van Blitterswijk, C. A.; Verbout, A. J.; de Bruijn, J. D.

    2010-01-01

    Calcium phosphate ceramics, commonly applied as bone graft substitutes, are a natural choice of scaffolding material for bone tissue engineering. Evidence shows that the chemical composition, macroporosity and microporosity of these ceramics influences their behavior as bone graft substitutes and bone tissue engineering scaffolds but little has been done to optimize these parameters. One method of optimization is to place focus on a particular parameter by normalizing the influence, as much as possible, of confounding parameters. This is difficult to accomplish with traditional fabrication techniques. In this study we describe a design based rapid prototyping method of manufacturing scaffolds with virtually identical macroporous architectures from different calcium phosphate ceramic compositions. Beta-tricalcium phosphate, hydroxyapatite (at two sintering temperatures) and biphasic calcium phosphate scaffolds were manufactured. The macro- and micro-architectures of the scaffolds were characterized as well as the influence of the manufacturing method on the chemistries of the calcium phosphate compositions. The structural characteristics of the resulting scaffolds were remarkably similar. The manufacturing process had little influence on the composition of the materials except for the consistent but small addition of, or increase in, a beta-tricalcium phosphate phase. Among other applications, scaffolds produced by the method described provide a means of examining the influence of different calcium phosphate compositions while confidently excluding the influence of the macroporous structure of the scaffolds. PMID:21069558

  1. A new method for rapid Canine retraction

    Directory of Open Access Journals (Sweden)

    "Khavari A

    2001-06-01

    Full Text Available Distraction osteogenesis method (Do in bone lengthening and rapid midpalatal expansion have shown the great ability of osteognic tissues for rapid bone formation under distraction force and special protocol with optimum rate of one millimeter per day. Periodontal membrane of teeth (PDM is the extension of periostium in the alveolar socked. Orthodontic force distracts PDM fibers in the tension side and then bone formation will begin.Objects: Rapid retraction of canine tooth into extraction space of first premolar by DO protocol in order to show the ability of the PDM in rapid bone formation. The other objective was reducing total orthodontic treatment time of extraction cases.Patients and Methods: Tweleve maxillary canines in six patients were retracted rapidly in three weeks by a custom-made tooth-born appliance. Radiographic records were taken to evaluate the effects of heavy applied force on canine and anchorage teeth.Results: Average retraction was 7.05 mm in three weeks (2.35 mm/week. Canines rotated distal- in by mean 3.5 degrees.Anchorage loss was from 0 to 0.8 mm with average of 0.3 mm.Root resorption of canines was negligible, and was not significant clinically. Periodontium was normal after rapid retraction. No hazard for pulp vitality was observed.Discussion: PDM responded well to heavy distraction force by Do protocol. Rapid canine retraction seems to be a safe method and can considerabely reduce orthodontic time.

  2. Fabrication of multi-well chips for spheroid cultures and implantable constructs through rapid prototyping techniques.

    Science.gov (United States)

    Lopa, Silvia; Piraino, Francesco; Kemp, Raymond J; Di Caro, Clelia; Lovati, Arianna B; Di Giancamillo, Alessia; Moroni, Lorenzo; Peretti, Giuseppe M; Rasponi, Marco; Moretti, Matteo

    2015-07-01

    Three-dimensional (3D) culture models are widely used in basic and translational research. In this study, to generate and culture multiple 3D cell spheroids, we exploited laser ablation and replica molding for the fabrication of polydimethylsiloxane (PDMS) multi-well chips, which were validated using articular chondrocytes (ACs). Multi-well ACs spheroids were comparable or superior to standard spheroids, as revealed by glycosaminoglycan and type-II collagen deposition. Moreover, the use of our multi-well chips significantly reduced the operation time for cell seeding and medium refresh. Exploiting a similar approach, we used clinical-grade fibrin to generate implantable multi-well constructs allowing for the precise distribution of multiple cell types. Multi-well fibrin constructs were seeded with ACs generating high cell density regions, as shown by histology and cell fluorescent staining. Multi-well constructs were compared to standard constructs with homogeneously distributed ACs. After 7 days in vitro, expression of SOX9, ACAN, COL2A1, and COMP was increased in both constructs, with multi-well constructs expressing significantly higher levels of chondrogenic genes than standard constructs. After 5 weeks in vivo, we found that despite a dramatic size reduction, the cell distribution pattern was maintained and glycosaminoglycan content per wet weight was significantly increased respect to pre-implantation samples. In conclusion, multi-well chips for the generation and culture of multiple cell spheroids can be fabricated by low-cost rapid prototyping techniques. Furthermore, these techniques can be used to generate implantable constructs with defined architecture and controlled cell distribution, allowing for in vitro and in vivo investigation of cell interactions in a 3D environment. © 2015 Wiley Periodicals, Inc.

  3. Assessment of Mechanical Performance of Bone Architecture Using Rapid Prototyping Models

    Science.gov (United States)

    Saparin, Peter; Woesz, Alexander; Thomsen, Jasper S.; Fratzl, Peter

    2008-06-01

    The aim of this on-going research project is to assess the influence of bone microarchitecture on the mechanical performance of trabecular bone. A testing chain consist-ing of three steps was established: 1) micro computed tomography (μCT) imaging of human trabecular bone; 2) building of models of the bone from a light-sensitive polymer using Rapid Prototyping (RP); 3) mechanical testing of the models in a material testing machine. A direct resampling procedure was developed to convert μCT data into the format of the RP machine. Standardized parameters for production and testing of the plastic models were established by use of regular cellular structures. Next, normal, osteoporotic, and extreme osteoporotic vertebral trabecular bone architectures were re-produced by RP and compression tested. We found that normal architecture of vertebral trabecular bone exhibit behaviour characteristic of a cellular structure. In normal bone the fracture occurs at much higher strain values that in osteoporotic bone. After the fracture a normal trabecular architecture is able to carry much higher loads than an osteoporotic architecture. However, no statistically significant differences were found in maximal stress during uniaxial compression of the central part of normal, osteoporotic, and extreme osteoporotic vertebral trabecular bone. This supports the hypothesis that osteoporotic trabecular bone can compensate for a loss of trabeculae by thickening the remaining trabeculae in the loading direction (compensatory hypertrophy). The developed approach could be used for mechanical evaluation of structural data acquired non-invasively and assessment of changes in performance of bone architecture.

  4. Development of a prototype lateral flow immunoassay (LFI for the rapid diagnosis of melioidosis.

    Directory of Open Access Journals (Sweden)

    Raymond L Houghton

    2014-03-01

    Full Text Available Burkholderia pseudomallei is a soil-dwelling bacterium and the causative agent of melioidosis. Isolation of B. pseudomallei from clinical samples is the "gold standard" for the diagnosis of melioidosis; results can take 3-7 days to produce. Alternatively, antibody-based tests have low specificity due to a high percentage of seropositive individuals in endemic areas. There is a clear need to develop a rapid point-of-care antigen detection assay for the diagnosis of melioidosis. Previously, we employed In vivo Microbial Antigen Discovery (InMAD to identify potential B. pseudomallei diagnostic biomarkers. The B. pseudomallei capsular polysaccharide (CPS and numerous protein antigens were identified as potential candidates. Here, we describe the development of a diagnostic immunoassay based on the detection of CPS. Following production of a CPS-specific monoclonal antibody (mAb, an antigen-capture immunoassay was developed to determine the concentration of CPS within a panel of melioidosis patient serum and urine samples. The same mAb was used to produce a prototype Active Melioidosis Detect Lateral Flow Immunoassay (AMD LFI; the limit of detection of the LFI for CPS is comparable to the antigen-capture immunoassay (∼0.2 ng/ml. The analytical reactivity (inclusivity of the AMD LFI was 98.7% (76/77 when tested against a large panel of B. pseudomallei isolates. Analytical specificity (cross-reactivity testing determined that 97.2% of B. pseudomallei near neighbor species (35/36 were not reactive. The non-reactive B. pseudomallei strain and the reactive near neighbor strain can be explained through genetic sequence analysis. Importantly, we show the AMD LFI is capable of detecting CPS in a variety of patient samples. The LFI is currently being evaluated in Thailand and Australia; the focus is to optimize and validate testing procedures on melioidosis patient samples prior to initiation of a large, multisite pre-clinical evaluation.

  5. Mechanical properties and cytotoxicity of a resorbable bioactive implant prepared by rapid prototyping technique.

    Science.gov (United States)

    El-Ghannam, Ahmed; Hart, Amanda; White, Dean; Cunningham, Larry

    2013-10-01

    Bioceramic processing using rapid prototyping technique (RPT) results in a fragile device that requires thermal treatment to improve the mechanical properties. This investigation evaluates the effect of thermal treatment on the mechanical, porosity, and bioactivity properties as well as the cytotoxicity of a porous silica-calcium phosphate nanocomposite (SCPC) implant prepared by RPT. Porous SCPC implant was subject to 3-h treatment at 800°C, 850°C, or 900°C. The compressive strength (s) and modulus of elasticity (E) were doubled when the sintering temperature is raised from 850 to 900°C measuring (s = 15.326 ± 2.95 MPa and E = 1095 ± 164 MPa) after the later treatment. The significant increase in mechanical properties takes place with minimal changes in the surface area and the percentage of pores in the range 1-356 μm. The SCPC implant prepared at 900°C was loaded with rh-BMP-2 and grafted into a segmental defect in the rabbit ulna. Histology analyses showed highly vascularized bone formation inside the defect. Histopathological analyses of the liver, spleen, kidney, heart, and the lung of rabbits grafted with and without SCPC demonstrated healthy tissues with no signs of toxicity or morphology alterations. Results of the study suggest that it is possible to engineering the mechanical properties of the SCPC implant without compromising its bioactivity. The enhanced bone formation inside the porous SCPC facilitated cell-mediated graft resorption and prohibited any accumulation of the material in the body organs. Copyright © 2013 Wiley Periodicals, Inc., a Wiley Company.

  6. A validation study of reconstructed rapid prototyping models produced by two technologies.

    Science.gov (United States)

    Dietrich, Christian Andreas; Ender, Andreas; Baumgartner, Stefan; Mehl, Albert

    2017-09-01

    To determine the accuracy (trueness and precision) of two different rapid prototyping (RP) techniques for the physical reproduction of three-dimensional (3D) digital orthodontic study casts, a comparative assessment using two 3D STL files of two different maxillary dentitions (two cases) as a reference was accomplished. Five RP replicas per case were fabricated using both stereolithography (SLA) and the PolyJet system. The 20 reproduced casts were digitized with a highly accurate reference scanner, and surface superimpositions were performed. Precision was measured by superimposing the digitized replicas within each case with themselves. Superimposing the digitized replicas with the corresponding STL reference files assessed trueness. Statistical significance between the two tested RP procedures was evaluated with independent-sample t-tests (P < .05). The SLA and PolyJet replicas showed statistically significant differences for trueness and precision. The precision of both tested RP systems was high, with mean deviations in stereolithographic models of 23 (±6) μm and in PolyJet replicas of 46 (±13) μm. The mean deviation for trueness in stereolithographic replicas was 109 (±4) μm, while in PolyJet replicas, it was 66 (±14) μm. Comparing the STL reference files, the PolyJet replicas showed higher trueness than the SLA models. But the precision measurements favored the SLA technique. The dimensional errors observed in this study were a maximum of 127 μm. In the present study, both types of reproduced digital orthodontic models are suitable for diagnostics and treatment planning.

  7. A scoping review of rapid review methods.

    Science.gov (United States)

    Tricco, Andrea C; Antony, Jesmin; Zarin, Wasifa; Strifler, Lisa; Ghassemi, Marco; Ivory, John; Perrier, Laure; Hutton, Brian; Moher, David; Straus, Sharon E

    2015-09-16

    Rapid reviews are a form of knowledge synthesis in which components of the systematic review process are simplified or omitted to produce information in a timely manner. Although numerous centers are conducting rapid reviews internationally, few studies have examined the methodological characteristics of rapid reviews. We aimed to examine articles, books, and reports that evaluated, compared, used or described rapid reviews or methods through a scoping review. MEDLINE, EMBASE, the Cochrane Library, internet websites of rapid review producers, and reference lists were searched to identify articles for inclusion. Two reviewers independently screened literature search results and abstracted data from included studies. Descriptive analysis was conducted. We included 100 articles plus one companion report that were published between 1997 and 2013. The studies were categorized as 84 application papers, seven development papers, six impact papers, and four comparison papers (one was included in two categories). The rapid reviews were conducted between 1 and 12 months, predominantly in Europe (58 %) and North America (20 %). The included studies failed to report 6 % to 73 % of the specific systematic review steps examined. Fifty unique rapid review methods were identified; 16 methods occurred more than once. Streamlined methods that were used in the 82 rapid reviews included limiting the literature search to published literature (24 %) or one database (2 %), limiting inclusion criteria by date (68 %) or language (49 %), having one person screen and another verify or screen excluded studies (6 %), having one person abstract data and another verify (23 %), not conducting risk of bias/quality appraisal (7 %) or having only one reviewer conduct the quality appraisal (7 %), and presenting results as a narrative summary (78 %). Four case studies were identified that compared the results of rapid reviews to systematic reviews. Three studies found that the conclusions between

  8. Semi-automated delineation of breast cancer tumors and subsequent materialization using three-dimensional printing (rapid prototyping).

    Science.gov (United States)

    Schulz-Wendtland, Rüdiger; Harz, Markus; Meier-Meitinger, Martina; Brehm, Barbara; Wacker, Till; Hahn, Horst K; Wagner, Florian; Wittenberg, Thomas; Beckmann, Matthias W; Uder, Michael; Fasching, Peter A; Emons, Julius

    2017-03-01

    Three-dimensional (3D) printing has become widely available, and a few cases of its use in clinical practice have been described. The aim of this study was to explore facilities for the semi-automated delineation of breast cancer tumors and to assess the feasibility of 3D printing of breast cancer tumors. In a case series of five patients, different 3D imaging methods-magnetic resonance imaging (MRI), digital breast tomosynthesis (DBT), and 3D ultrasound-were used to capture 3D data for breast cancer tumors. The volumes of the breast tumors were calculated to assess the comparability of the breast tumor models, and the MRI information was used to render models on a commercially available 3D printer to materialize the tumors. The tumor volumes calculated from the different 3D methods appeared to be comparable. Tumor models with volumes between 325 mm 3 and 7,770 mm 3 were printed and compared with the models rendered from MRI. The materialization of the tumors reflected the computer models of them. 3D printing (rapid prototyping) appears to be feasible. Scenarios for the clinical use of the technology might include presenting the model to the surgeon to provide a better understanding of the tumor's spatial characteristics in the breast, in order to improve decision-making in relation to neoadjuvant chemotherapy or surgical approaches. J. Surg. Oncol. 2017;115:238-242. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  9. Immediate facial rehabilitation in cancer patients using CAD-CAM and rapid prototyping technology: a pilot study.

    Science.gov (United States)

    Ciocca, Leonardo; Fantini, Massimiliano; Marchetti, Claudio; Scotti, Roberto; Monaco, Carlo

    2010-06-01

    This study describes the workflow in a procedure to create a provisional facial prosthesis for cancer patients using digital and rapid prototyping technologies without the need for supporting craniofacial implants. An integrated workflow procedure aimed at the construction of provisional silicone prosthesis was used to rehabilitate a facial disfigurement in a patient who had undergone ablative surgery of the midface. A laser scan of the defect was obtained, and a digital model of the patient's face was constructed using virtual mirroring of the healthy side and referencing the "Nose Digital Library." The missing volume of the face was reconstructed, and a rapid-prototyped mold was devised to process the silicone prosthesis. A provisional eyeglasses-supported prosthesis designed with a CAD/CAM-projected titanium substructure was connected using the micro-components of implant prosthetic devices. The workflow described herein offers a viable procedure for quickly restoring facial defects by means of provisional prosthetic rehabilitation.

  10. A MATLAB Library for Rapid Prototyping of Wireless Communications Algorithms with the Universal Software Radio Peripheral (USRP) Radio Family

    Science.gov (United States)

    2013-06-01

    A MATLAB Library for Rapid Prototyping of Wireless Communications Algorithms with the Universal Software Radio Peripheral ( USRP ) Radio Family...Algorithms with the Universal Software Radio Peripheral ( USRP ) Radio Family Gunjan Verma and Paul Yu Computational and Information Sciences...Universal Software Radio Pheriphal ( USRP ) Radio Family 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Gunjan Verma

  11. Rapid prototyping of nano- and micro-patterned substrates for the control of cell neuritogenesis by topographic and chemical cues

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Ajay V.; Gailite, Lasma; Vyas, Varun [European School of Molecular Medicine (SEMM), IFOM-IEO Campus, Via Adamello 16, I-20139 Milano (Italy); CIMAINA and Dipartimento di Fisica, Universita di Milano, via Celoria 16, I-20133 Milano (Italy); Lenardi, Cristina, E-mail: cristina.lenardi@mi.infn.it [CIMAINA and Dipartimento di Scienze Molecolari Applicate ai Biosistemi, Universita di Milano, via Trentacoste 2, I-20134 Milano (Italy); Fondazione Filarete, viale Ortles 22/4, I-20139 Milano (Italy); Forti, Stefania [CIMAINA and Dipartimento di Fisica, Universita di Milano, via Celoria 16, I-20133 Milano (Italy); Matteoli, Michela [Dipartimento di Farmacologia, Chemioterapia e Tossicologia Medica, Universita di Milano, via Vanvitelli 32, I-20139 Milano (Italy); Fondazione Filarete, viale Ortles 22/4, I-20139 Milano (Italy); Milani, Paolo, E-mail: paolo.milani@mi.infn.it [CIMAINA and Dipartimento di Fisica, Universita di Milano, via Celoria 16, I-20133 Milano (Italy); Fondazione Filarete, viale Ortles 22/4, I-20139 Milano (Italy)

    2011-07-20

    Rapid prototyping of titania substrates with micro and nanofeatures is obtained by combining nanosphere lithography with supersonic cluster beam deposition on protein-functionalized glass supports. The proliferation and differentiation of PC12 cells were studied on these substrates. The facile control and modification of the substrate structure at the micro- and nanoscale allowed us to characterize the role of functional and structural features on neuritogenesis and to control this phenomenon by identifying the optimal topography.

  12. Application of Computer-Aided Designing and Rapid Prototyping Technologies in Reconstruction of Blowout Fractures of the Orbital Floor.

    Science.gov (United States)

    Tabaković, Saša Z; Konstantinović, Vitomir S; Radosavljević, Radivoje; Movrin, Dejan; Hadžistević, Miodrag; Hatab, Nur

    2015-07-01

    Traumatology of the maxillofacial region represents a wide range of different types of facial skeletal injuries and encompasses numerous treatment methods. Application of computer-aided design (CAD) in combination with rapid prototyping (RP) technologies and three-dimensional computed tomography techniques facilitates surgical therapy planning for efficient treatment. The purpose of this study is to determine the efficiency of individually designed implants of poly-DL-lactide (PDLLA) in the reconstruction of blowout fractures of the orbital floor. In the course of a surgical treatment, individually designed implants manufactured by CAD/RP technologies were used. Preoperative analysis and postoperative monitoring were conducted to evaluate the successfulness of orbital floor reconstruction using customized PDLLA implants, based on: presence of diplopia, paresthesia of infraorbital nerve, and presence of enophthalmos. In 6 of the 10 patients, diplopia completely disappeared immediately after surgical procedure. Diplopia gradually disappeared after 1 month in 3 patients, whereas in 1, it remained even after 6 months. In 7 patients, paresthesia disappeared within a month after surgery and in 3 patients within 2 months. Postoperative average Orbital volume (OV) of the injured side (13.333 ± 3.177) was significantly reduced in comparison with preoperative OV (15.847 ± 3.361) after reconstruction of the orbital floor with customized PDLLA implant (P virtual preoperative modeling allows easier preoperative preparation and yields satisfactory functional and esthetic outcomes.

  13. Updates on the Construction of an Eyeglass-Supported Nasal Prosthesis Using Computer-Aided Design and Rapid Prototyping Technology.

    Science.gov (United States)

    Ciocca, Leonardo; Tarsitano, Achille; Marchetti, Claudio; Scotti, Roberto

    2016-01-01

    This study was undertaken to design an updated connection system for an eyeglass-supported nasal prosthesis using rapid prototyping techniques. The substructure was developed with two main endpoints in mind: the connection to the silicone and the connection to the eyeglasses. The mold design was also updated; the mold was composed of various parts, each carefully designed to allow for easy release after silicone processing and to facilitate extraction of the prosthesis without any strain. The approach used in this study enabled perfect transfer of the reciprocal position of the prosthesis with respect to the eyeglasses, from the virtual to the clinical environment. Moreover, the reduction in thickness improved the flexibility of the prosthesis and promoted adaptation to the contours of the skin, even during functional movements. The method described here is a simplified and viable alternative to standard construction techniques for nasal prostheses and offers improved esthetic and functional results when no bone is available for implant-supported prostheses. © 2015 by the American College of Prosthodontists.

  14. Chest-wall reconstruction with a customized titanium-alloy prosthesis fabricated by 3D printing and rapid prototyping.

    Science.gov (United States)

    Wen, Xiaopeng; Gao, Shan; Feng, Jinteng; Li, Shuo; Gao, Rui; Zhang, Guangjian

    2018-01-08

    As 3D printing technology emerge, there is increasing demand for a more customizable implant in the repair of chest-wall bony defects. This article aims to present a custom design and fabrication method for repairing bony defects of the chest wall following tumour resection, which utilizes three-dimensional (3D) printing and rapid-prototyping technology. A 3D model of the bony defect was generated after acquiring helical CT data. A customized prosthesis was then designed using computer-aided design (CAD) and mirroring technology, and fabricated using titanium-alloy powder. The mechanical properties of the printed prosthesis were investigated using ANSYS software. The yield strength of the titanium-alloy prosthesis was 950 ± 14 MPa (mean ± SD), and its ultimate strength was 1005 ± 26 MPa. The 3D finite element analyses revealed that the equivalent stress distribution of each prosthesis was unifrom. The symmetry and reconstruction quality contour of the repaired chest wall was satisfactory. No rejection or infection occurred during the 6-month follow-up period. Chest-wall reconstruction with a customized titanium-alloy prosthesis is a reliable technique for repairing bony defects.

  15. Rapid prototyping of all-solution-processed multi-lengthscale electrodes using polymer-induced thin film wrinkling.

    Science.gov (United States)

    Gabardo, Christine M; Adams-McGavin, Robert C; Fung, Barnabas C; Mahoney, Eric J; Fang, Qiyin; Soleymani, Leyla

    2017-02-13

    Three-dimensional electrodes that are controllable over multiple lengthscales are very important for use in bioanalytical systems that integrate solid-phase devices with solution-phase samples. Here we present a fabrication method based on all-solution-processing and thin film wrinkling using smart polymers that is ideal for rapid prototyping of tunable three-dimensional electrodes and is extendable to large volume manufacturing. Although all-solution-processing is an attractive alternative to vapor-based techniques for low-cost manufacturing of electrodes, it often results in films suffering from low conductivity and poor substrate adhesion. These limitations are addressed here by using a smart polymer to create a conformal layer of overlapping wrinkles on the substrate to shorten the current path and embed the conductor onto the polymer layer. The structural evolution of these wrinkled electrodes, deposited by electroless deposition onto a nanoparticle seed layer, is studied at varying deposition times to understand its effects on structural parameters such as porosity, wrinkle wavelength and height. Furthermore, the effect of structural parameters on functional properties such as electro-active surface area and surface-enhanced Raman scattering is investigated. It is found that wrinkling of electroless-deposited thin films can be used to reduce sheet resistance, increase surface area, and enhance the surface-enhanced Raman scattering signal.

  16. Operative simulation of anterior clinoidectomy using a rapid prototyping model molded by a three-dimensional printer.

    Science.gov (United States)

    Okonogi, Shinichi; Kondo, Kosuke; Harada, Naoyuki; Masuda, Hiroyuki; Nemoto, Masaaki; Sugo, Nobuo

    2017-05-15

    As the anatomical three-dimensional (3D) positional relationship around the anterior clinoid process (ACP) is complex, experience of many surgeries is necessary to understand anterior clinoidectomy (AC). We prepared a 3D synthetic image from computed tomographic angiography (CTA) and magnetic resonance imaging (MRI) data and a rapid prototyping (RP) model from the imaging data using a 3D printer. The objective of this study was to evaluate anatomical reproduction of the 3D synthetic image and intraosseous region after AC in the RP model. In addition, the usefulness of the RP model for operative simulation was investigated. The subjects were 51 patients who were examined by CTA and MRI before surgery. The size of the ACP, thickness and length of the optic nerve and artery, and intraosseous length after AC were measured in the 3D synthetic image and RP model, and reproducibility in the RP model was evaluated. In addition, 10 neurosurgeons performed AC in the completed RP models to investigate their usefulness for operative simulation. The RP model reproduced the region in the vicinity of the ACP in the 3D synthetic image, including the intraosseous region, at a high accuracy. In addition, drilling of the RP model was a useful operative simulation method of AC. The RP model of the vicinity of ACP, prepared using a 3D printer, showed favorable anatomical reproducibility, including reproduction of the intraosseous region. In addition, it was concluded that this RP model is useful as a surgical education tool for drilling.

  17. Rapid prototyping of all-solution-processed multi-lengthscale electrodes using polymer-induced thin film wrinkling

    Science.gov (United States)

    Gabardo, Christine M.; Adams-McGavin, Robert C.; Fung, Barnabas C.; Mahoney, Eric J.; Fang, Qiyin; Soleymani, Leyla

    2017-02-01

    Three-dimensional electrodes that are controllable over multiple lengthscales are very important for use in bioanalytical systems that integrate solid-phase devices with solution-phase samples. Here we present a fabrication method based on all-solution-processing and thin film wrinkling using smart polymers that is ideal for rapid prototyping of tunable three-dimensional electrodes and is extendable to large volume manufacturing. Although all-solution-processing is an attractive alternative to vapor-based techniques for low-cost manufacturing of electrodes, it often results in films suffering from low conductivity and poor substrate adhesion. These limitations are addressed here by using a smart polymer to create a conformal layer of overlapping wrinkles on the substrate to shorten the current path and embed the conductor onto the polymer layer. The structural evolution of these wrinkled electrodes, deposited by electroless deposition onto a nanoparticle seed layer, is studied at varying deposition times to understand its effects on structural parameters such as porosity, wrinkle wavelength and height. Furthermore, the effect of structural parameters on functional properties such as electro-active surface area and surface-enhanced Raman scattering is investigated. It is found that wrinkling of electroless-deposited thin films can be used to reduce sheet resistance, increase surface area, and enhance the surface-enhanced Raman scattering signal.

  18. Using INGRES as a rapid prototyping device during development of management information applications

    Energy Technology Data Exchange (ETDEWEB)

    Brice, L.; Connell, J.; Shafer, D.

    1983-01-01

    This paper presents case studies from the Administrative Data Processing Division of the Los Alamos National Laboratory where a prototyping too, the INGRES relational database system, has been used to develop management information systems. The tool has proved valuable in satisfying user requirements and expectations, and in aiding data processing in the analysis and specification phases of the system life cycle. The prototype approach helps enormously in bridging the developer-user communication gap and has been found to add a negligible amount of cost to the entire software development project. Presented here are four case studies of how INGRES has been employed in prototyping. Also presented are examples of specific INGRES features and how they were used in one of the case studies and further examples involving another similar case. Special considerations and cautions are required when using INGRES for prototyping, but the overall conclusion is that it is a tool which has tremendously benefited our organization. Whether the final implemented system is INGRES-based or not, prototyping greatly enhances the possibility of complete, correct and unambiguous specifications prior to final software product development.

  19. High-throughput rapid-prototyping of low-cost paper-based microfluidics.

    Science.gov (United States)

    Ghaderinezhad, Fariba; Amin, Reza; Temirel, Mikail; Yenilmez, Bekir; Wentworth, Adam; Tasoglu, Savas

    2017-06-15

    Paper-based micro analytical devices offer significant advantages compared to the conventional microfluidic chips including cost-effectiveness, ease of fabrication, and ease of use while preserving critical features including strong capillary action and biological compatibility. In this work, we demonstrate an inexpensive, rapid method for high-throughput fabrication of paper-based microfluidics by patterning hydrophobic barriers using a desktop pen plotter integrated with a custom-made, low-cost paper feeder. We tested various types of commercial permanent markers and compared their water-resistant capabilities for creating hydrophobic barriers. Additionally, we studied the performance of markers with different types of paper, plotting speeds, and pattern dimensions. To verify the effectiveness of the presented fabrication method, colorimetric analysis was performed on the results of a glucose assay.

  20. Hybrid molecular–continuum methods: From prototypes to coupling software

    KAUST Repository

    Neumann, Philipp

    2014-02-01

    In this contribution, we review software requirements in hybrid molecular-continuum simulations. For this purpose, we analyze a prototype implementation which combines two frameworks-the Molecular Dynamics framework MarDyn and the framework Peano for spatially adaptive mesh-based simulations-and point out particular challenges of a general coupling software. Based on this analysis, we discuss the software design of our recently published coupling tool. We explain details on its overall structure and show how the challenges that arise in respective couplings are resolved by the software. © 2013 Elsevier Ltd. All rights reserved.

  1. New layer-based imaging and rapid prototyping techniques for computer-aided design and manufacture of custom dental restoration.

    Science.gov (United States)

    Lee, M-Y; Chang, C-C; Ku, Y C

    2008-01-01

    Fixed dental restoration by conventional methods greatly relies on the skill and experience of the dental technician. The quality and accuracy of the final product depends mostly on the technician's subjective judgment. In addition, the traditional manual operation involves many complex procedures, and is a time-consuming and labour-intensive job. Most importantly, no quantitative design and manufacturing information is preserved for future retrieval. In this paper, a new device for scanning the dental profile and reconstructing 3D digital information of a dental model based on a layer-based imaging technique, called abrasive computer tomography (ACT) was designed in-house and proposed for the design of custom dental restoration. The fixed partial dental restoration was then produced by rapid prototyping (RP) and computer numerical control (CNC) machining methods based on the ACT scanned digital information. A force feedback sculptor (FreeForm system, Sensible Technologies, Inc., Cambridge MA, USA), which comprises 3D Touch technology, was applied to modify the morphology and design of the fixed dental restoration. In addition, a comparison of conventional manual operation and digital manufacture using both RP and CNC machining technologies for fixed dental restoration production is presented. Finally, a digital custom fixed restoration manufacturing protocol integrating proposed layer-based dental profile scanning, computer-aided design, 3D force feedback feature modification and advanced fixed restoration manufacturing techniques is illustrated. The proposed method provides solid evidence that computer-aided design and manufacturing technologies may become a new avenue for custom-made fixed restoration design, analysis, and production in the 21st century.

  2. Rapid prototyping and inclined plane technique in the treatment of maxillofacial malformations in a fox.

    Science.gov (United States)

    Freitas, Elisangela P; Rahal, Sheila C; Teixeira, Carlos R; Silva, Jorge V L; Noritomi, Pedro Y; Villela, Carlos H S; Yamashita, Seizo

    2010-03-01

    An approximately 9-month-old fox (Pseudalopex vetulus) was presented with malocclusion and deviation of the lower jaw to the right side. Orthodontic treatment was performed using the inclined plane technique. Virtual 3D models and prototypes of the head were based on computed tomography (CT) image data to assist in diagnosis and treatment.

  3. Rapid Prototyping across the Spectrum: RF to Optical 3D Electromagnetic Structures

    Science.gov (United States)

    2015-11-17

    19 Figure 11: Nanoparticle arrays fabricated using electron...sputtering [138], (b) Small spherical wire antenna covered with conductive paint [73], (c) Optical image of an antenna during the printing process [135...abilities (e.g. nanoparticle loaded polymers that can be ink-jet deposited enable unique plasmonic fields in a device) [59]. Prototyping processes can be

  4. Rapid Prototyping by 3D Printing for Advanced Radio Communications at 80 GHz and Above

    DEFF Research Database (Denmark)

    Salazar, Adrian Ruiz; Rommel, Simon; Anufriyev, Eldar

    2016-01-01

    This paper discusses the potential of 3D printing for the manufacturing of spiral phase plates for the generation of radio vortex beams for advanced radio communications. The design and prototyping of a number of phase plates for communications at 80GHz with radio vortex beams is discussed...

  5. Rapid Prototyping of an Electrically-Small Antenna for Binaural-Hearing Instruments

    DEFF Research Database (Denmark)

    Ruaro, Andrea; Thaysen, Jesper; Jakobsen, Kaj Bjarne

    2015-01-01

    ). This study analyzes the main RF parameters (dielectric constant, loss tangent, surface roughness) and applies the results to the modeling of the prototype of an electrically small (ESA) antenna for binaural hearing instruments applications. After discussing the specific technology choices...... and their relevancies, it is shown how the analyzed parameters can be used to obtain good correlation between simulations and measurements....

  6. Rapid prototyping and inclined plane technique in the treatment of maxillofacial malformations in a fox

    Science.gov (United States)

    Freitas, Elisangela P.; Rahal, Sheila C.; Teixeira, Carlos R.; Silva, Jorge V.L.; Noritomi, Pedro Y.; Villela, Carlos H.S.; Yamashita, Seizo

    2010-01-01

    An approximately 9-month-old fox (Pseudalopex vetulus) was presented with malocclusion and deviation of the lower jaw to the right side. Orthodontic treatment was performed using the inclined plane technique. Virtual 3D models and prototypes of the head were based on computed tomography (CT) image data to assist in diagnosis and treatment. PMID:20514249

  7. An Embedded Systems Laboratory to Support Rapid Prototyping of Robotics and the Internet of Things

    Science.gov (United States)

    Hamblen, J. O.; van Bekkum, G. M. E.

    2013-01-01

    This paper describes a new approach for a course and laboratory designed to allow students to develop low-cost prototypes of robotic and other embedded devices that feature Internet connectivity, I/O, networking, a real-time operating system (RTOS), and object-oriented C/C++. The application programming interface (API) libraries provided permit…

  8. Development of a prototype immunochromatographic test for rapid diagnosis of respiratory adenovirus infection

    Directory of Open Access Journals (Sweden)

    Inarei Paulini

    2017-09-01

    The immunochromatographic assay prototype was sufficiently sensitive to detect B (3, C (2 and 5, and F (41 adenovirus samples. Although based on preliminary data, the test demonstrated the same performance as direct immunofluorescence, but with the advantage of being a point-of-care test. Further studies are still needed to confirm its effectiveness in clinical practice.

  9. Sucrose-based fabrication of 3D-networked, cylindrical microfluidic channels for rapid prototyping of lab-on-a-chip and vaso-mimetic devices.

    Science.gov (United States)

    Lee, Jiwon; Paek, Jungwook; Kim, Jaeyoun

    2012-08-07

    We present a new fabrication scheme for 3D-networked, cylindrical microfluidic (MF) channels based on shaping, bonding, and assembly of sucrose fibers. It is a simple, cleanroom-free, and environment-friendly method, ideal for rapid prototyping of lab-on-a-chip devices. Despite its simplicity, it can realize complex 3D MF channel architectures such as cylindrical tapers, internal loops, end-to-side junctions, tapered junctions, and stenosis. The last two will be of special use for realizing vaso-mimetic MF structures. It also enables molding with polymers incompatible with high-temperature processing.

  10. Rapid determination of capsaicinoids by colorimetric method

    OpenAIRE

    Ryu, Wang-Kyun; Kim, Hee-Woong; Kim, Geun-Dong; Rhee, Hae-Ik

    2016-01-01

    Capsaicinoids, the pungent component of chili peppers, are generally analyzed by precise analytical techniques, such as gas chromatography and high-performance liquid chromatography (HPLC), but these are not practical for the mass analyses of samples. To analyze mass samples rapidly, a colorimetric method was suggested. In this work, pigments and capsaicinoids were efficiently separated from chili pepper extract by sequential solid–liquid extraction and liquid–liquid extraction in test tubes ...

  11. Prototipaje rápido de estructuras craneofaciales Rapid prototyping of craniofacial structures

    Directory of Open Access Journals (Sweden)

    Juan Felipe Isaza

    2008-12-01

    Full Text Available Este artículo presenta una descripción de la tecnología de Prototipaje Rápido o Rapid Prototyping (RP aplicada a la medicina, específicamente a problemas craneofaciales, con la cual se pueden fabricar modelos sólidos 3D por adición de material. A su vez se describe una aplicación a partir de la simulación de una cirugía para insertar cuatro implantes mandibulares, los cuales constituyen la base de una prótesis fija soportada por implantes. La simulación del procedimiento quirúrgico comenzó con la obtención de la geometría mandibular a partir del procesamiento de imágenes biomédicas, provenientes de una Tomografia Axial Computarizada (TAC de una mujer adulta, totalmente edéntula. Dicho proceso se realizó utilizando el software GIB Points 3D, desarrollado dentro del presente trabajo. Con el software se obtuvo un archivo de texto con la nube de puntos 3D de la mandíbula que posteriormente fue exportado a ProEngineer Wildfire 3.0, desde el cual se generó un archivo en formato estándar STL, compatible con la mayoría de máquinas RP. La tecnología usada para la impresión 3D, fue la de “deposición de hilo fundido” o Fused Deposition Modeling (FDM. Se logró obtener un modelo plástico de una mandíbula, de gran calidad anatómica y dimensional, utilizando tecnología disponible enColombia. Además, se simuló con éxito el procedimiento quirúrgico para lainstalación de cuatro implantes utilizando las herramientas que se usarían enla cirugía real. En general, la metodología implementada puede ser utilizadapara la planificación quirúrgica y así evitar procedimientos de ensayo y errorque puedan poner en riesgo la salud del paciente. También como herramientade comunicación para explicarle al paciente los procedimientos quirúrgicos aque será sometido. Además, puede ser usado con fines docentes para el entrenamientode estudiantes, haciendo más efectivos los procesos de aprendizajeen el ámbito clínico que a su

  12. Error rate of multi-level rapid prototyping trajectories for pedicle screw placement in lumbar and sacral spine

    Directory of Open Access Journals (Sweden)

    Merc Matjaz

    2014-10-01

    Full Text Available 【Abstract】Objective: Free-hand pedicle screw placement has a high incidence of pedicle perforation which can be reduced with fluoroscopy, navigation or an alternative rapid prototyping drill guide template. In our study the error rate of multi-level templates for pedicle screw placement in lumbar and sacral regions was evaluated. Methods: A case series study was performed on 11 patients. Seventy-two screws were implanted using multilevel drill guide templates manufactured with selective laser sintering. According to the optimal screw direction preoperatively defi ned, an analysis of screw misplacement was performed. Displacement, deviation and screw length difference were measured. The learning curve was also estimated. Results: Twelve screws (17% were placed more than 3.125 mm out of its optimal position in the centre of pedicle. The tip of the 16 screws (22% was misplaced more than 6.25 mm out of the predicted optimal position. According to our predefi ned goal, 19 screws (26% were implanted inaccurately. In 10 cases the screw length was selected incorrectly: 1 (1% screw was too long and 9 (13% were too short. No clinical signs of neurovascular lesion were observed. Learning curve was insignifi cantly noticeable (P=0.129. Conclusion: In our study, the procedure of manufacturing and applying multi-level drill guide templates has a 26% chance of screw misplacement. However, that rate does not coincide with pedicle perforation incidence and neurovascular injury. These facts along with a comparison to compatible studies make it possible to summarize that multi-level templates are satisfactorily accurate and allow precise screw placement with a clinically irrelevant mistake factor. Therefore templates could potentially represent a useful tool for routine pedicle screw placement. Key words: Drill guide; Template; Inaccuracy; Perforation; Radiation exposure

  13. Effect of annealing procedure on the bonding of ceramic to cobalt-chromium alloys fabricated by rapid prototyping.

    Science.gov (United States)

    Tulga, Ayca

    2017-08-22

    An annealing procedure is a heat treatment process to improve the mechanical properties of cobalt-chromium (Co-Cr) alloys. However, information is lacking about the effect of the annealing process on the bonding ability of ceramic to Co-Cr alloys fabricated by rapid prototyping. The purpose of this in vitro study was to evaluate the effects of the fabrication techniques and the annealing procedure on the shear bond strength of ceramic to Co-Cr alloys fabricated by different techniques. Ninety-six cylindrical specimens (10-mm diameter, 10-mm height) made of Co-Cr alloy were prepared by casting (C), milling (M), direct process powder-bed (LaserCUSING) with and without annealing (CL+, CL), and direct metal laser sintering (DMLS) with annealing (EL+) and without annealing (EL). After the application of ceramic to the metal specimens, the metal-ceramic bond strength was assessed using a shear force test at a crosshead speed of 0.5 mm/min. Shear bond strength values were statistically analyzed by 1-way ANOVA and Tukey multiple comparison tests (α=.05). Although statistically significant differences were found among the 3 groups (M, 29.87 ±2.06; EL, 38.92 ±2.04; and CL+, 40.93 ±2.21; P=.002), no significant differences were found among the others (P>.05). The debonding surfaces of all specimens exhibited mixed failure mode. These results showed that the direct process powder-bed method is promising in terms of metal-ceramic bonding ability. The manufacturing technique of Co-Cr alloys and the annealing process influence metal-ceramic bonding. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  14. Creating pathology models from MRI data: a comparison of virtual 3D modelling and rapid prototyping techniques.

    Science.gov (United States)

    Challoner, Alexandra; Erolin, Caroline

    2013-06-01

    This paper discusses a pilot study in collaboration between the Centre for Anatomy and Human Identification and the Pathology Department at Ninewells Hospital, Dundee. Anonymised patient MRI data depicting renal cancer was used to create a virtual 3D model and two rapid prototype models of the kidneys and surrounding anatomy. A questionnaire was conducted to collect feedback from tutors and students in order to evaluate the models and determine user preference. It was found that the majority preferred the physical models to the virtual model.

  15. Open-Source Wax RepRap 3-D Printer for Rapid Prototyping Paper-Based Microfluidics.

    Science.gov (United States)

    Pearce, J M; Anzalone, N C; Heldt, C L

    2016-08-01

    The open-source release of self-replicating rapid prototypers (RepRaps) has created a rich opportunity for low-cost distributed digital fabrication of complex 3-D objects such as scientific equipment. For example, 3-D printable reactionware devices offer the opportunity to combine open hardware microfluidic handling with lab-on-a-chip reactionware to radically reduce costs and increase the number and complexity of microfluidic applications. To further drive down the cost while improving the performance of lab-on-a-chip paper-based microfluidic prototyping, this study reports on the development of a RepRap upgrade capable of converting a Prusa Mendel RepRap into a wax 3-D printer for paper-based microfluidic applications. An open-source hardware approach is used to demonstrate a 3-D printable upgrade for the 3-D printer, which combines a heated syringe pump with the RepRap/Arduino 3-D control. The bill of materials, designs, basic assembly, and use instructions are provided, along with a completely free and open-source software tool chain. The open-source hardware device described here accelerates the potential of the nascent field of electrochemical detection combined with paper-based microfluidics by dropping the marginal cost of prototyping to nearly zero while accelerating the turnover between paper-based microfluidic designs. © 2016 Society for Laboratory Automation and Screening.

  16. Parameter optimization and stretch enhancement of AISI 316 sheet using rapid prototyping technique

    Science.gov (United States)

    Moayedfar, M.; Rani, A. M.; Hanaei, H.; Ahmad, A.; Tale, A.

    2017-10-01

    Incremental sheet forming is a flexible manufacturing process which uses the indenter point-to-point force to shape the sheet metal workpiece into manufactured parts in batch production series. However, the problem sometimes arising from this process is the low plastic point in the stress-strain diagram of the material which leads the low stretching amount before ultra-tensile strain point. Hence, a set of experiments is designed to find the optimum forming parameters in this process for optimum sheet thickness distribution while both sides of the sheet are considered for the surface quality improvement. A five-axis high-speed CNC milling machine is employed to deliver the proper motion based on the programming system while the clamping system for holding the sheet metal was a blank mould. Finally, an electron microscope and roughness machine are utilized to evaluate the surface structure of final parts, illustrate any defect may cause during the forming process and examine the roughness of the final part surface accordingly. The best interaction between parameters is obtained with the optimum values which lead the maximum sheet thickness distribution of 4.211e-01 logarithmic elongation when the depth was 24mm with respect to the design. This study demonstrates that this rapid forming method offers an alternative solution for surface quality improvement of 65% avoiding the low probability of cracks and low probability of crystal structure changes.

  17. Rapid prototyping of microbial cell factories via genome-scale engineering.

    Science.gov (United States)

    Si, Tong; Xiao, Han; Zhao, Huimin

    2015-11-15

    Advances in reading, writing and editing genetic materials have greatly expanded our ability to reprogram biological systems at the resolution of a single nucleotide and on the scale of a whole genome. Such capacity has greatly accelerated the cycles of design, build and test to engineer microbes for efficient synthesis of fuels, chemicals and drugs. In this review, we summarize the emerging technologies that have been applied, or are potentially useful for genome-scale engineering in microbial systems. We will focus on the development of high-throughput methodologies, which may accelerate the prototyping of microbial cell factories. Copyright © 2014 Elsevier Inc. All rights reserved.

  18. Rapid Column Extraction method for SoilRapid Column Extraction method for Soil

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, Sherrod, L. III; Culligan, Brian K.

    2005-11-07

    The analysis of actinides in environmental soil and sediment samples is very important for environmental monitoring as well as for emergency preparedness. A new, rapid actinide separation method has been developed and implemented that provides total dissolution of large soil samples, high chemical recoveries and effective removal of matrix interferences. This method uses stacked TEVA Resin{reg_sign}, TRU Resin{reg_sign} and DGA-Resin{reg_sign} cartridges from Eichrom Technologies (Darien, IL, USA) that allows the rapid separation of plutonium (Pu) neptunium (Np), uranium (U), americium (Am), and curium (Cm) using a single multi-stage column combined with alpha spectrometry. The method combines a rapid fusion step for total dissolution to dissolve refractory analytes and matrix removal using cerium fluoride precipitation to remove the difficult soil matrix. By using vacuum box cartridge technology with rapid flow rates, sample preparation time is minimized.

  19. Low-temperature deposition manufacturing: A novel and promising rapid prototyping technology for the fabrication of tissue-engineered scaffold.

    Science.gov (United States)

    Liu, Wei; Wang, Daming; Huang, Jianghong; Wei, You; Xiong, Jianyi; Zhu, Weimin; Duan, Li; Chen, Jielin; Sun, Rong; Wang, Daping

    2017-01-01

    Developed in recent years, low-temperature deposition manufacturing (LDM) represents one of the most promising rapid prototyping technologies. It is not only based on rapid deposition manufacturing process but also combined with phase separation process. Besides the controlled macropore size, tissue-engineered scaffold fabricated by LDM has inter-connected micropores in the deposited lines. More importantly, it is a green manufacturing process that involves non-heating liquefying of materials. It has been employed to fabricate tissue-engineered scaffolds for bone, cartilage, blood vessel and nerve tissue regenerations. It is a promising technology in the fabrication of tissue-engineered scaffold similar to ideal scaffold and the design of complex organs. In the current paper, this novel LDM technology is introduced, and its control parameters, biomedical applications and challenges are included and discussed as well. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Accuracy of using computer-aided rapid prototyping templates for mandible reconstruction with an iliac crest graft.

    Science.gov (United States)

    Shu, Da-long; Liu, Xiang-zhen; Guo, Bing; Ran, Wei; Liao, Xin; Zhang, Yun-yan

    2014-06-24

    This study aimed to evaluate the accuracy of surgical outcomes in free iliac crest mandibular reconstructions that were carried out with virtual surgical plans and rapid prototyping templates. This study evaluated eight patients who underwent mandibular osteotomy and reconstruction with free iliac crest grafts using virtual surgical planning and designed guiding templates. Operations were performed using the prefabricated guiding templates. Postoperative three-dimensional computer models were overlaid and compared with the preoperatively designed models in the same coordinate system. Compared to the virtual osteotomy, the mean error of distance of the actual mandibular osteotomy was 2.06 ± 0.86 mm. When compared to the virtual harvested grafts, the mean error volume of the actual harvested grafts was 1412.22 ± 439.24 mm3 (9.12% ± 2.84%). The mean error between the volume of the actual harvested grafts and the shaped grafts was 2094.35 ± 929.12 mm3 (12.40% ± 5.50%). The use of computer-aided rapid prototyping templates for virtual surgical planning appears to positively influence the accuracy of mandibular reconstruction.

  1. Rapid prototyping of microfluidic switches in poly(dimethyl siloxane) and their actuation by electro-osmotic flow

    Science.gov (United States)

    Duffy, David C.; Schueller, Olivier J. A.; Brittain, Scott T.; Whitesides, George M.

    1999-09-01

    This paper describes a procedure for rapidly and conveniently prototyping microfluidic devices that are useful with aqueous solutions. A design (with diameters of channels icons/Journals/Common/ge" ALT="ge" ALIGN="TOP"/>20 µm) is created in a computer-aided design program and printed at high resolution on a transparency. This transparency is used as a mask in photolithography to create a master in positive relief photoresist: casting poly(dimethyl siloxane) (PDMS) against this master yields a polymeric replica containing a network of bas-relief channels. The channels are closed and sealed irreversibly by oxidizing the replica and another flat substrate (PDMS, glass, silicon, silicon oxide) in an oxygen plasma and bringing the two surfaces into conformal contact. Oxidation of the polymer allows the formation of a seal without using adhesives; it also generates channels that support electro-osmotic flow (EOF) and fill easily with aqueous solutions. Two microfluidic devices - a fluidic switch and a side channel flow controller - have been fabricated using this rapid prototyping methodology. These devices were tested using aqueous solutions as the test fluid and actuated by EOF.

  2. Pen-on-paper strategy for point-of-care testing: Rapid prototyping of fully written microfluidic biosensor.

    Science.gov (United States)

    Li, Zedong; Li, Fei; Xing, Yue; Liu, Zhi; You, Minli; Li, Yingchun; Wen, Ting; Qu, Zhiguo; Ling Li, Xiao; Xu, Feng

    2017-12-15

    Paper-based microfluidic biosensors have recently attracted increasing attentions in point-of-care testing (POCT) territories benefiting from their affordable, accessible and eco-friendly features, where technologies for fabricating such biosensors are preferred to be equipment free, easy-to-operate and capable of rapid prototyping. In this work, we developed a pen-on-paper (PoP) strategy based on two custom-made pens, i.e., a wax pen and a conductive-ink pen, to fully write paper-based microfluidic biosensors through directly writing both microfluidic channels and electrodes. Particularly, the proposed wax pen is competent to realize one-step fabrication of wax channels on paper, as the melted wax penetrates into paper during writing process without any post-treatments. The practical applications of the fabricated paper-based microfluidic biosensors are demonstrated by both colorimetric detection of Salmonella typhimurium DNA with detection limit of 1nM and electrochemical measurement of glucose with detection limit of 1mM. The developed PoP strategy for making microfluidic biosensors on paper characterized by true simplicity, prominent portability and excellent capability for rapid prototyping shows promising prospect in POCT applications. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Dimensional Error in Rapid Prototyping with Open Source Software and Low-cost 3D-printer.

    Science.gov (United States)

    Rendón-Medina, Marco A; Andrade-Delgado, Laura; Telich-Tarriba, Jose E; Fuente-Del-Campo, Antonio; Altamirano-Arcos, Carlos A

    2018-01-01

    Rapid prototyping models (RPMs) had been extensively used in craniofacial and maxillofacial surgery, especially in areas such as orthognathic surgery, posttraumatic or oncological reconstructions, and implantology. Economic limitations are higher in developing countries such as Mexico, where resources dedicated to health care are limited, therefore limiting the use of RPM to few selected centers. This article aims to determine the dimensional error of a low-cost fused deposition modeling 3D printer (Tronxy P802MA, Shenzhen, Tronxy Technology Co), with Open source software. An ordinary dry human mandible was scanned with a computed tomography device. The data were processed with open software to build a rapid prototype with a fused deposition machine. Linear measurements were performed to find the mean absolute and relative difference. The mean absolute and relative difference was 0.65 mm and 1.96%, respectively ( P = 0.96). Low-cost FDM machines and Open Source Software are excellent options to manufacture RPM, with the benefit of low cost and a similar relative error than other more expensive technologies.

  4. An Objective Prototype-Based Method for Dual-Polarization Radar Clutter Identification

    Directory of Open Access Journals (Sweden)

    Guang Wen

    2017-04-01

    Full Text Available A prototype-based method is developed to discriminate different types of clutter (ground clutter, sea clutter, and insects from weather echoes using polarimetric measurements and their textures. This method employs a clustering algorithm to generate data groups from the training dataset, each of which is modeled as a weighted Gaussian distribution called a “prototype.” Two classification algorithms are proposed based on the prototypes, namely maximum prototype likelihood classifier (MPLC and Bayesian classifier (BC. In the MPLC, the probability of a data point with respect to each prototype is estimated to retrieve the final class label under the maximum likelihood criterion. The BC models the probability density function as a Gaussian mixture composed by the prototypes. The class label is obtained under the maximum a posterior criterion. The two algorithms are applied to S-band dual-polarization CP-2 weather radar data in Southeast Queensland, Australia. The classification results for the test dataset are compared with the NCAR fuzzy-logic particle identification algorithm. Generally good agreement is found for weather echo and ground clutter; however, the confusion matrix indicates that the techniques tend to differ from each other on the recognition of insects.

  5. A brief review of dispensing-based rapid prototyping techniques in tissue scaffold fabrication: role of modeling on scaffold properties prediction.

    Science.gov (United States)

    Li, M G; Tian, X Y; Chen, X B

    2009-09-01

    Artificial scaffolds play vital roles in tissue engineering as they provide a supportive environment for cell attachment, proliferation and differentiation during tissue formation. Fabrication of tissue scaffolds is thus of fundamental importance for tissue engineering. Of the variety of scaffold fabrication techniques available, rapid prototyping (RP) methods have attracted a great deal of attention in recent years. This method can improve conventional scaffold fabrication by controlling scaffold microstructure, incorporating cells into scaffolds and regulating cell distribution. All of these contribute towards the ultimate goal of tissue engineering: functional tissues or organs. Dispensing is typically used in different RP techniques to implement the layer-by-layer fabrication process. This article reviews RP methods in tissue scaffold fabrication, with emphasis on dispensing-based techniques, and analyzes the effects of different process factors on fabrication performance, including flow rate, pore size and porosity, and mechanical cell damage that can occur in the bio-manufacturing process.

  6. A brief review of dispensing-based rapid prototyping techniques in tissue scaffold fabrication: role of modeling on scaffold properties prediction

    Energy Technology Data Exchange (ETDEWEB)

    Li, M G; Chen, X B [Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5A9 (Canada); Tian, X Y, E-mail: mil715@mail.usask.c [Division of Biomedical Engineering, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5A9 (Canada)

    2009-09-15

    Artificial scaffolds play vital roles in tissue engineering as they provide a supportive environment for cell attachment, proliferation and differentiation during tissue formation. Fabrication of tissue scaffolds is thus of fundamental importance for tissue engineering. Of the variety of scaffold fabrication techniques available, rapid prototyping (RP) methods have attracted a great deal of attention in recent years. This method can improve conventional scaffold fabrication by controlling scaffold microstructure, incorporating cells into scaffolds and regulating cell distribution. All of these contribute towards the ultimate goal of tissue engineering: functional tissues or organs. Dispensing is typically used in different RP techniques to implement the layer-by-layer fabrication process. This article reviews RP methods in tissue scaffold fabrication, with emphasis on dispensing-based techniques, and analyzes the effects of different process factors on fabrication performance, including flow rate, pore size and porosity, and mechanical cell damage that can occur in the bio-manufacturing process. (topical review)

  7. Rapid prototyping of an automated video surveillance system: a hardware-software co-design approach

    Science.gov (United States)

    Ngo, Hau T.; Rakvic, Ryan N.; Broussard, Randy P.; Ives, Robert W.

    2011-06-01

    FPGA devices with embedded DSP and memory blocks, and high-speed interfaces are ideal for real-time video processing applications. In this work, a hardware-software co-design approach is proposed to effectively utilize FPGA features for a prototype of an automated video surveillance system. Time-critical steps of the video surveillance algorithm are designed and implemented in the FPGAs logic elements to maximize parallel processing. Other non timecritical tasks are achieved by executing a high level language program on an embedded Nios-II processor. Pre-tested and verified video and interface functions from a standard video framework are utilized to significantly reduce development and verification time. Custom and parallel processing modules are integrated into the video processing chain by Altera's Avalon Streaming video protocol. Other data control interfaces are achieved by connecting hardware controllers to a Nios-II processor using Altera's Avalon Memory Mapped protocol.

  8. Rapid Prototyping for Heterogeneous Multicomponent Systems: An MPEG-4 Stream over a UMTS Communication Link

    Directory of Open Access Journals (Sweden)

    Sorel Y

    2006-01-01

    Full Text Available Future generations of mobile phones, including advanced video and digital communication layers, represent a great challenge in terms of real-time embedded systems. Programmable multicomponent architectures can provide suitable target solutions combining flexibility and computation power. The aim of our work is to develop a fast and automatic prototyping methodology dedicated to signal processing application implementation on parallel heterogeneous architectures, two major features required by future systems. This paper presents the whole methodology based on the SynDEx CAD tool that directly generates a distributed implementation onto various platforms from a high-level application description, taking real-time aspects into account. It illustrates the methodology in the context of real-time distributed executives for multilayer applications based on an MPEG-4 video codec and a UMTS telecommunication link.

  9. Rapid Prototyping for Heterogeneous Multicomponent Systems: An MPEG-4 Stream over a UMTS Communication Link

    Science.gov (United States)

    Raulet, M.; Urban, F.; Nezan, J.-F.; Moy, C.; Deforges, O.; Sorel, Y.

    2006-12-01

    Future generations of mobile phones, including advanced video and digital communication layers, represent a great challenge in terms of real-time embedded systems. Programmable multicomponent architectures can provide suitable target solutions combining flexibility and computation power. The aim of our work is to develop a fast and automatic prototyping methodology dedicated to signal processing application implementation on parallel heterogeneous architectures, two major features required by future systems. This paper presents the whole methodology based on the SynDEx CAD tool that directly generates a distributed implementation onto various platforms from a high-level application description, taking real-time aspects into account. It illustrates the methodology in the context of real-time distributed executives for multilayer applications based on an MPEG-4 video codec and a UMTS telecommunication link.

  10. Rapid prototyping 3D virtual world interfaces within a virtual factory environment

    Science.gov (United States)

    Kosta, Charles Paul; Krolak, Patrick D.

    1993-01-01

    On-going work into user requirements analysis using CLIPS (NASA/JSC) expert systems as an intelligent event simulator has led to research into three-dimensional (3D) interfaces. Previous work involved CLIPS and two-dimensional (2D) models. Integral to this work was the development of the University of Massachusetts Lowell parallel version of CLIPS, called PCLIPS. This allowed us to create both a Software Bus and a group problem-solving environment for expert systems development. By shifting the PCLIPS paradigm to use the VEOS messaging protocol we have merged VEOS (HlTL/Seattle) and CLIPS into a distributed virtual worlds prototyping environment (VCLIPS). VCLIPS uses the VEOS protocol layer to allow multiple experts to cooperate on a single problem. We have begun to look at the control of a virtual factory. In the virtual factory there are actors and objects as found in our Lincoln Logs Factory of the Future project. In this artificial reality architecture there are three VCLIPS entities in action. One entity is responsible for display and user events in the 3D virtual world. Another is responsible for either simulating the virtual factory or communicating with the real factory. The third is a user interface expert. The interface expert maps user input levels, within the current prototype, to control information for the factory. The interface to the virtual factory is based on a camera paradigm. The graphics subsystem generates camera views of the factory on standard X-Window displays. The camera allows for view control and object control. Control or the factory is accomplished by the user reaching into the camera views to perform object interactions. All communication between the separate CLIPS expert systems is done through VEOS.

  11. Rapid prototyping for tissue-engineered bone scaffold by 3D printing and biocompatibility study.

    Science.gov (United States)

    He, Hui-Yu; Zhang, Jia-Yu; Mi, Xue; Hu, Yang; Gu, Xiao-Yu

    2015-01-01

    The prototyping of tissue-engineered bone scaffold (calcined goat spongy bone-biphasic ceramic composite/PVA gel) by 3D printing was performed, and the biocompatibility of the fabricated bone scaffold was studied. Pre-designed STL file was imported into the GXYZ303010-XYLE 3D printing system, and the tissue-engineered bone scaffold was fabricated by 3D printing using gel extrusion. Rabbit bone marrow stromal cells (BMSCs) were cultured in vitro and then inoculated to the sterilized bone scaffold obtained by 3D printing. The growth of rabbit BMSCs on the bone scaffold was observed under the scanning electron microscope (SEM). The effect of the tissue-engineered bone scaffold on the proliferation and differentiation of rabbit BMSCs using MTT assay. Universal testing machine was adopted to test the tensile strength of the bone scaffold. The leachate of the bone scaffold was prepared and injected into the New Zealand rabbits. Cytotoxicity test, acute toxicity test, pyrogenic test and intracutaneous stimulation test were performed to assess the biocompatibility of the bone scaffold. Bone scaffold manufactured by 3D printing had uniform pore size with the porosity of about 68.3%. The pores were well interconnected, and the bone scaffold showed excellent mechanical property. Rabbit BMSCs grew and proliferated on the surface of the bone scaffold after adherence. MTT assay indicated that the proliferation and differentiation of rabbit BMSCs on the bone scaffold did not differ significantly from that of the cells in the control. In vivo experiments proved that the bone scaffold fabricated by 3D printing had no acute toxicity, pyrogenic reaction or stimulation. Bone scaffold manufactured by 3D printing allows the rabbit BMSCs to adhere, grow and proliferate and exhibits excellent biomechanical property and high biocompatibility. 3D printing has a good application prospect in the prototyping of tissue-engineered bone scaffold.

  12. Assessment of a virtual functional prototyping process for the rapid manufacture of passive-dynamic ankle-foot orthoses.

    Science.gov (United States)

    Schrank, Elisa S; Hitch, Lester; Wallace, Kevin; Moore, Richard; Stanhope, Steven J

    2013-10-01

    Passive-dynamic ankle-foot orthosis (PD-AFO) bending stiffness is a key functional characteristic for achieving enhanced gait function. However, current orthosis customization methods inhibit objective premanufacture tuning of the PD-AFO bending stiffness, making optimization of orthosis function challenging. We have developed a novel virtual functional prototyping (VFP) process, which harnesses the strengths of computer aided design (CAD) model parameterization and finite element analysis, to quantitatively tune and predict the functional characteristics of a PD-AFO, which is rapidly manufactured via fused deposition modeling (FDM). The purpose of this study was to assess the VFP process for PD-AFO bending stiffness. A PD-AFO CAD model was customized for a healthy subject and tuned to four bending stiffness values via VFP. Two sets of each tuned model were fabricated via FDM using medical-grade polycarbonate (PC-ISO). Dimensional accuracy of the fabricated orthoses was excellent (average 0.51 ± 0.39 mm). Manufacturing precision ranged from 0.0 to 0.74 Nm/deg (average 0.30 ± 0.36 Nm/deg). Bending stiffness prediction accuracy was within 1 Nm/deg using the manufacturer provided PC-ISO elastic modulus (average 0.48 ± 0.35 Nm/deg). Using an experimentally derived PC-ISO elastic modulus improved the optimized bending stiffness prediction accuracy (average 0.29 ± 0.57 Nm/deg). Robustness of the derived modulus was tested by carrying out the VFP process for a disparate subject, tuning the PD-AFO model to five bending stiffness values. For this disparate subject, bending stiffness prediction accuracy was strong (average 0.20 ± 0.14 Nm/deg). Overall, the VFP process had excellent dimensional accuracy, good manufacturing precision, and strong prediction accuracy with the derived modulus. Implementing VFP as part of our PD-AFO customization and manufacturing framework, which also includes fit customization, provides a novel and powerful method to

  13. 20170313 - Rapid Prototyping of Physiologically-Based Toxicokinetic (PBTK) Models (SOT annual meeting)

    Science.gov (United States)

    Determining the tissue concentrations resulting from chemical exposure (i.e., toxicokinetics (TK)) is essential in emergency or other situations where time and data are lacking. Generic TK models can be created rapidly using in vitro assays and computational approaches to generat...

  14. Rapid prototyping of a double-layer polyurethane-collagen conduit for peripheral nerve regeneration.

    Science.gov (United States)

    Cui, Tongkui; Yan, Yongnian; Zhang, Renji; Liu, Li; Xu, Wei; Wang, Xiaohong

    2009-03-01

    A new technique for preparing double-layer polyurethane (PU)-collagen nerve conduits for peripheral nerve repair via a double-nozzle, low-temperature, deposition manufacturing (DLDM) system has been developed. The DLDM system is based on a digital prototyping approach, and uses a combination of thermally induced phase separation and freeze-drying. With this system, two kinds of biomaterials with different properties can be combined to produce scaffold structures with good biocompatibility in the inner layer and with the desired mechanical strength protruded by the outer. The forming precision is high, the wall thickness can be controlled, and a tight connection between the two layers can be achieved. The effects of changing the processing parameters and the material temperature on the structure of the scaffolds have been investigated. Additionally, the effect of material concentration on the mechanical strength and hydrophilic properties of the scaffolds has also been studied. Ideal peripheral nerve repair conduits, comprising an outer microporous layer of PU and internal oriented filaments of collagen, have been manufactured through optimizing the processing parameters and the biomaterial concentrations.

  15. A Rapid Prototyping Tool for Embedded, Real-Time Hierarchical Control Systems

    Directory of Open Access Journals (Sweden)

    Hugo Andrade

    2008-12-01

    Full Text Available Laboratory Virtual Instrumentation and Engineering Workbench (LabVIEW is a graphical programming tool based on the dataflow language G. Recently, runtime support for a hard real-time environment has become available for LabVIEW, which makes it an option for embedded systems prototyping. Due to its characteristics, the environment presents itself as an ideal tool for both the design and implementation of embedded software. In this paper, we study the design and implementation of embedded software by using G as the specification language and the LabVIEW RT real-time platform. One of the main advantages of this approach is that the environment leads itself to a very smooth transition from design to implementation, allowing for powerful cosimulation strategies (e.g., hardware in the loop, runtime modeling. We characterize the semantics and formal model of computation of G. We compare it to other models of computation and develop design rules and algorithms to propose sound embedded design in the language. We investigate the specification and mapping of hierarchical control systems in LabVIEW and G. Finally, we describe the development of a state-of-the-art embedded motion control system using LabVIEW as the specification, simulation and implementation tool, using the proposed design principles. The solution is state-of-the-art in terms of flexibility and control performance.

  16. A Rapid Prototyping Tool for Embedded, Real-Time Hierarchical Control Systems

    Directory of Open Access Journals (Sweden)

    Ramamoorthy Subramanian

    2008-01-01

    Full Text Available Abstract Laboratory Virtual Instrumentation and Engineering Workbench (LabVIEW is a graphical programming tool based on the dataflow language G. Recently, runtime support for a hard real-time environment has become available for LabVIEW, which makes it an option for embedded systems prototyping. Due to its characteristics, the environment presents itself as an ideal tool for both the design and implementation of embedded software. In this paper, we study the design and implementation of embedded software by using G as the specification language and the LabVIEW RT real-time platform. One of the main advantages of this approach is that the environment leads itself to a very smooth transition from design to implementation, allowing for powerful cosimulation strategies (e.g., hardware in the loop, runtime modeling. We characterize the semantics and formal model of computation of G. We compare it to other models of computation and develop design rules and algorithms to propose sound embedded design in the language. We investigate the specification and mapping of hierarchical control systems in LabVIEW and G. Finally, we describe the development of a state-of-the-art embedded motion control system using LabVIEW as the specification, simulation and implementation tool, using the proposed design principles. The solution is state-of-the-art in terms of flexibility and control performance.

  17. A review method for UML requirements analysis model employing system-side prototyping.

    Science.gov (United States)

    Ogata, Shinpei; Matsuura, Saeko

    2013-12-01

    User interface prototyping is an effective method for users to validate the requirements defined by analysts at an early stage of a software development. However, a user interface prototype system offers weak support for the analysts to verify the consistency of the specifications about internal aspects of a system such as business logic. As the result, the inconsistency causes a lot of rework costs because the inconsistency often makes the developers impossible to actualize the system based on the specifications. For verifying such consistency, functional prototyping is an effective method for the analysts, but it needs a lot of costs and more detailed specifications. In this paper, we propose a review method so that analysts can verify the consistency among several different kinds of diagrams in UML efficiently by employing system-side prototyping without the detailed model. The system-side prototype system does not have any functions to achieve business logic, but visualizes the results of the integration among the diagrams in UML as Web pages. The usefulness of our proposal was evaluated by applying our proposal into a development of Library Management System (LMS) for a laboratory. This development was conducted by a group. As the result, our proposal was useful for discovering the serious inconsistency caused by the misunderstanding among the members of the group.

  18. Rapid determination of capsaicinoids by colorimetric method.

    Science.gov (United States)

    Ryu, Wang-Kyun; Kim, Hee-Woong; Kim, Geun-Dong; Rhee, Hae-Ik

    2017-10-01

    Capsaicinoids, the pungent component of chili peppers, are generally analyzed by precise analytical techniques, such as gas chromatography and high-performance liquid chromatography (HPLC), but these are not practical for the mass analyses of samples. To analyze mass samples rapidly, a colorimetric method was suggested. In this work, pigments and capsaicinoids were efficiently separated from chili pepper extract by sequential solid-liquid extraction and liquid-liquid extraction in test tubes followed by a colorimetric analysis on the capsaicinoids by a selective chromogenic reaction with Gibbs reagent (2,6-dichloroquinone-4-chloroimide). In the comparison of the capsaicinoid content by the colorimetric method and HPLC using acetone extracts of fresh pepper and dry red pepper as samples, R2 was 0.9973 and 0.9816, respectively, which shows a high linear correlation. In addition, a minimum of 1 μg/mL capsaicinoids can be detected and it was therefore determined that the method can efficiently analyze a great quantity of samples in a short time. Copyright © 2016. Published by Elsevier B.V.

  19. Rapid determination of capsaicinoids by colorimetric method

    Directory of Open Access Journals (Sweden)

    Wang-Kyun Ryu

    2017-10-01

    Full Text Available Capsaicinoids, the pungent component of chili peppers, are generally analyzed by precise analytical techniques, such as gas chromatography and high-performance liquid chromatography (HPLC, but these are not practical for the mass analyses of samples. To analyze mass samples rapidly, a colorimetric method was suggested. In this work, pigments and capsaicinoids were efficiently separated from chili pepper extract by sequential solid–liquid extraction and liquid–liquid extraction in test tubes followed by a colorimetric analysis on the capsaicinoids by a selective chromogenic reaction with Gibbs reagent (2,6-dichloroquinone-4-chloroimide. In the comparison of the capsaicinoid content by the colorimetric method and HPLC using acetone extracts of fresh pepper and dry red pepper as samples, R2 was 0.9973 and 0.9816, respectively, which shows a high linear correlation. In addition, a minimum of 1 μg/mL capsaicinoids can be detected and it was therefore determined that the method can efficiently analyze a great quantity of samples in a short time.

  20. Multi-Resolution Rapid Prototyping of Vehicle Cooling Systems: Approach and Test Results

    Science.gov (United States)

    2014-08-01

    components within the system. 3. System-level: assembly of reduced-order models of components for rapid generation of results for the entire vehicle...using reduced-order models (with increased resolution) on specific components/ assemblies , while using regular reduced-order models for the remaining...Single and Multi-Evaporator Subcritical Vapor Compression Systems”, M.S. Thesis, University of Illinois at Urbana- Champaign. Siegel, J., 2007, Corba

  1. A Software/Hardware Platform For Rapid Prototyping of Video and Multimedia Designs

    OpenAIRE

    Schumacher, Paul; Mattavelli, Marco; Chirila-Rus, Adrian; Turney, Robert

    2005-01-01

    Traditional design and test of complex multimedia systems involves a large number of test vectors and is a difficult and time-consuming task. The simulation times are prohibitively long on current desktop computers. Driving actual design scenarios and timing burst behavior which produce real-time effects is difficult to do with current simulation environments. This paper describes a rapid emulation framework for accessing multiple hardware IP blocks on an FPGA. This solution involves an abstr...

  2. Optimized Design and Testing of a Prototype Military Bridge System for Rapid In-Theater Construction

    Science.gov (United States)

    2006-11-01

    MLC 30 were applied to the system with multiple load cases for each axle, truck, and track loading. The load cases were applied sequentially to...flexural failure due to concrete crushing along the center of slab span. The failure was identified with center span cracking and associated concrete...Layer Prefabricated FRP Grids for Rapid Bridge Deck Construction: Case Study. ASCE Journal of Composites for Construction, 10, 201-121. Berg, A. C

  3. A novel method for rapid in vitro radiobioassay

    Science.gov (United States)

    Crawford, Evan Bogert

    Rapid and accurate analysis of internal human exposure to radionuclides is essential to the effective triage and treatment of citizens who have possibly been exposed to radioactive materials in the environment. The two most likely scenarios in which a large number of citizens would be exposed are the detonation of a radiation dispersal device (RDD, "dirty bomb") or the accidental release of an isotope from an industrial source such as a radioisotopic thermal generator (RTG). In the event of the release and dispersion of radioactive materials into the environment in a large city, the entire population of the city -- including all commuting workers and tourists -- would have to be rapidly tested, both to satisfy the psychological needs of the citizens who were exposed to the mental trauma of a possible radiation dose, and to satisfy the immediate medical needs of those who received the highest doses and greatest levels of internal contamination -- those who would best benefit from rapid, intensive medical care. In this research a prototype rapid screening method to screen urine samples for the presence of up to five isotopes, both individually and in a mixture, has been developed. The isotopes used to develop this method are Co-60, Sr-90, Cs-137, Pu-238, and Am-241. This method avoids time-intensive chemical separations via the preparation and counting of a single sample on multiple detectors, and analyzing the spectra for isotope-specific markers. A rapid liquid-liquid separation using an organic extractive scintillator can be used to help quantify the activity of the alpha-emitting isotopes. The method provides quantifiable results in less than five minutes for the activity of beta/gamma-emitting isotopes when present in the sample at the intervention level as defined by the Centers for Disease Control and Prevention (CDC), and quantifiable results for the activity levels of alpha-emitting isotopes present at their respective intervention levels in approximately 30

  4. A method for nanofluidic device prototyping using elastomeric collapse

    Science.gov (United States)

    Park, Seung-min; Huh, Yun Suk; Craighead, Harold G.; Erickson, David

    2009-01-01

    Nanofluidics represents a promising solution to problems in fields ranging from biomolecular analysis to optical property tuning. Recently a number of simple nanofluidic fabrication techniques have been introduced that exploit the deformability of elastomeric materials like polydimethylsiloxane (PDMS). These techniques are limited by the complexity of the devices that can be fabricated, which can only create straight or irregular channels normal to the direction of an applied strain. Here, we report a technique for nanofluidic fabrication based on the controlled collapse of microchannel structures. As is demonstrated, this method converts the easy to control vertical dimension of a PDMS mold to the lateral dimension of a nanochannel. We demonstrate here the creation of complex nanochannel structures as small as 60 nm and provide simple design rules for determining the conditions under which nanochannel formation will occur. The applicability of the technique to biomolecular analysis is demonstrated by showing DNA elongation in a nanochannel and a technique for optofluidic surface enhanced Raman detection of nucleic acids. PMID:19717418

  5. Correction of hemifacial microsomia with the help of mirror imaging and a rapid prototyping technique: case report.

    Science.gov (United States)

    Zhou, Libin; He, Lisheng; Shang, Hongtao; Liu, Guicai; Zhao, Jinlong; Liu, Yanpu

    2009-09-01

    A 23-year-old man presented with an 8-year history of unilateral hemifacial microsomia. A three-dimensional model of the maxillofacial bones was generated after acquisition of helical computed tomographic data. A customised implant model was designed by projecting a mirror image of the healthy mandible on to the three-dimensional model. A resin model of the implant was then made using a rapid prototyping machine. A polymeric biomaterial was sculpted according to the model and implanted into the affected side of the mandible to restore his facial symmetry. The hemifacial microsomia was corrected and a symmetrical facial contour obtained. No complications developed during the 6-year follow-up.

  6. Rapid prototyping to design a customized locking plate for pancarpal arthrodesis in a giant breed dog.

    Science.gov (United States)

    Petazzoni, M; Nicetto, T

    2014-01-01

    This report describes the treatment of traumatic carpal hyperextension in a giant breed dog by pancarpal arthrodesis using a custom-made Fixin locking plate, created with the aid of a three-dimensional plastic model of the bones of the antebrachium produced by rapid prototyping technology. A three-year-old 104 kg male Mastiff dog was admitted for treatment of carpal hyperextension injury. After diagnosis of carpal instability, surgery was recommended. Computed tomography images were used to create a life-size three-dimensional plastic model of the forelimb. The model was used as the basis for constructing a customized 12-hole Fixin locking plate. The plate was used to attain successful pancarpal arthrodesis in the animal. Radiographic examination after 74 and 140 days revealed signs of osseous union of the arthrodesis. Further clinical and radiographic follow-up examination three years later did not reveal any changes in implant position or complications.

  7. Characterization of a Reconfigurable Free-Space Optical Channel for Embedded Computer Applications with Experimental Validation Using Rapid Prototyping Technology

    Directory of Open Access Journals (Sweden)

    Lim Theodore

    2007-01-01

    Full Text Available Free-space optical interconnects (FSOIs are widely seen as a potential solution to current and future bandwidth bottlenecks for parallel processors. In this paper, an FSOI system called optical highway (OH is proposed. The OH uses polarizing beam splitter-liquid crystal plate (PBS/LC assemblies to perform reconfigurable beam combination functions. The properties of the OH make it suitable for embedding complex network topologies such as completed connected mesh or hypercube. This paper proposes the use of rapid prototyping technology for implementing an optomechanical system suitable for studying the reconfigurable characteristics of a free-space optical channel. Additionally, it reports how the limited contrast ratio of the optical components can affect the attenuation of the optical signal and the crosstalk caused by misdirected signals. Different techniques are also proposed in order to increase the optical modulation amplitude (OMA of the system.

  8. Characterization of a Reconfigurable Free-Space Optical Channel for Embedded Computer Applications with Experimental Validation Using Rapid Prototyping Technology

    Directory of Open Access Journals (Sweden)

    Rafael Gil-Otero

    2007-02-01

    Full Text Available Free-space optical interconnects (FSOIs are widely seen as a potential solution to current and future bandwidth bottlenecks for parallel processors. In this paper, an FSOI system called optical highway (OH is proposed. The OH uses polarizing beam splitter-liquid crystal plate (PBS/LC assemblies to perform reconfigurable beam combination functions. The properties of the OH make it suitable for embedding complex network topologies such as completed connected mesh or hypercube. This paper proposes the use of rapid prototyping technology for implementing an optomechanical system suitable for studying the reconfigurable characteristics of a free-space optical channel. Additionally, it reports how the limited contrast ratio of the optical components can affect the attenuation of the optical signal and the crosstalk caused by misdirected signals. Different techniques are also proposed in order to increase the optical modulation amplitude (OMA of the system.

  9. Rapid sealing of porcine renal blood vessels, ex vivo, using a high power, 1470-nm laser, and laparoscopic prototype

    Science.gov (United States)

    Hardy, Luke A.; Hutchens, Thomas C.; Larson, Eric R.; Gonzalez, David A.; Chang, Chun-Hung; Nau, William H.; Fried, Nathaniel M.

    2017-05-01

    Energy-based, radiofrequency (RF) and ultrasonic (US) devices currently provide rapid sealing of blood vessels during laparoscopic procedures. We are exploring infrared lasers as an alternate energy modality for vessel sealing, capable of generating less collateral thermal damage. Previous studies demonstrated feasibility of sealing vessels in an in vivo porcine model using a 1470-nm laser. However, the initial prototype was designed for testing in open surgery and featured tissue clasping and light delivery mechanisms incompatible with laparoscopic surgery. In this study, a laparoscopic prototype similar to devices currently in surgical use was developed, and performance tests were conducted on porcine renal blood vessels, ex vivo. The 5-mm outer-diameter laparoscopic prototype featured a traditional Maryland jaw configuration that enables tissue manipulation and blunt dissection. Laser energy was delivered through a 550-μm-core-diameter optical fiber with side-delivery from the lower jaw and beam dimensions of 18-mm length×1.2-mm width. The 1470-nm diode laser delivered 68 W with 3-s activation time, consistent with vessel seal times associated with RF and US-based devices. A total of 69 fresh porcine renal vessels with mean diameter of 3.3±1.7 mm were tested, ex vivo. Vessels smaller than 5-mm diameter were consistently sealed (48/51) with burst pressures greater than malignant hypertension blood pressure (180 mmHg), averaging 1038±474 mmHg. Vessels larger than 5 mm were not consistently sealed (6/18), yielding burst pressures of only 174±221 mmHg. Seal width, thermal damage zone, and thermal spread averaged 1.7±0.8, 3.4±0.7, and 1.0±0.4 mm, respectively. Results demonstrated that the 5-mm optical laparoscopic prototype consistently sealed vessels less than 5-mm diameter with low thermal spread. Further in vivo studies are planned to test the performance across a variety of vessels and tissues.

  10. Workstation-Based Simulation for Rapid Prototyping and Piloted Evaluation of Control System Designs

    Science.gov (United States)

    Mansur, M. Hossein; Colbourne, Jason D.; Chang, Yu-Kuang; Aiken, Edwin W. (Technical Monitor)

    1998-01-01

    The development and optimization of flight control systems for modem fixed- and rotary-. wing aircraft consume a significant portion of the overall time and cost of aircraft development. Substantial savings can be achieved if the time required to develop and flight test the control system, and the cost, is reduced. To bring about such reductions, software tools such as Matlab/Simulink are being used to readily implement block diagrams and rapidly evaluate the expected responses of the completed system. Moreover, tools such as CONDUIT (CONtrol Designer's Unified InTerface) have been developed that enable the controls engineers to optimize their control laws and ensure that all the relevant quantitative criteria are satisfied, all within a fully interactive, user friendly, unified software environment.

  11. Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers.

    Science.gov (United States)

    Bellingham, Alyssa; Bromhead, Nicholas; Fontecchio, Adam

    2017-05-29

    There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

  12. matter: an R package for rapid prototyping with larger-than-memory datasets on disk.

    Science.gov (United States)

    Bemis, Kylie A; Vitek, Olga

    2017-06-15

    We introduce matter , an R package for direct interactions with larger-than-memory datasets, stored in an arbitrary number of files of any size. matter is primarily designed for datasets in new and rapidly evolving file formats, which may lack extensive software support. matter enables a wide variety of data exploration and manipulation steps, and is extensible to many bioinformatics applications. It supports reproducible research by minimizing the need of converting and storing data in multiple formats. We illustrate the performance of matter in conjunction with the Bioconductor package Cardinal for analysis of high-resolution, high-throughput mass spectrometry imaging experiments. The package, vignettes, and examples of applications in several areas of bioinformatics are available open-source at www.bioconductor.org under the Artistic-2.0 license. o.vitek@neu.edu.

  13. Rapid Prototyping of Slot Die Devices for Roll to Roll Production of EL Fibers

    Directory of Open Access Journals (Sweden)

    Alyssa Bellingham

    2017-05-01

    Full Text Available There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

  14. Application of the rapid prototyping technique to design a customized temporomandibular joint used to treat temporomandibular ankylosis

    Science.gov (United States)

    Chaware, Suresh M.; Bagaria, Vaibhav; Kuthe, Abhay

    2009-01-01

    Anthropometric variations in humans make it difficult to replace a temporomandibular joint (TMJ), successfully using a standard “one-size-fits-all” prosthesis. The case report presents a unique concept of total TMJ replacement with customized and modified TMJ prosthesis, which is cost-effective and provides the best fit for the patient. The process involved in designing and modifications over the existing prosthesis are also described. A 12-year- old female who presented for treatment of left unilateral TMJ ankylosis underwent the surgery for total TMJ replacement. A three-dimensional computed tomography (CT) scan suggested features of bony ankylosis of left TMJ. CT images were converted to a sterolithographic model using CAD software and a rapid prototyping machine. A process of rapid manufacturing was then used to manufacture the customized prosthesis. Postoperative recovery was uneventful, with an improvement in mouth opening of 3.5 cm and painless jaw movements. Three years postsurgery, the patient is pain-free, has a mouth opening of about 4.0 cm and enjoys a normal diet. The postoperative radiographs concur with the excellent clinical results. The use of CAD/CAM technique to design the custom-made prosthesis, using orthopaedically proven structural materials, significantly improves the predictability and success rates of TMJ replacement surgery. PMID:19881026

  15. The development of silk fibroin scaffolds using an indirect rapid prototyping approach: morphological analysis and cell growth monitoring by spectral-domain optical coherence tomography.

    Science.gov (United States)

    Liu, M J J; Chou, S M; Chua, C K; Tay, B C M; Ng, B K

    2013-02-01

    To date, naturally derived biomaterials are rarely used in advanced tissue engineering (TE) methods despite their superior biocompatibility. This is because these native materials, which consist mainly of proteins and polysaccharides, do not possess the ability to withstand harsh processing conditions. Unlike synthetic polymers, natural materials degrade and decompose rapidly in the presence of chemical solvents and high temperature, respectively. Thus, the fabrication of tissue scaffolds using natural biomaterials is often carried out using conventional techniques, where the efficiency in mass transport of nutrients and removal of waste products within the construct is compromised. The present study identified silk fibroin (SF) protein as a suitable material for the application of rapid prototyping (RP) or additive manufacturing (AM) technology. Using the indirect RP method, via the use of a mould, SF tissue scaffolds with both macro- and micro-morphological features can be produced and qualitatively examined by spectral-domain optical coherence tomography (SD-OCT). The advanced imaging technique showed the ability to differentiate the cells and SF material by producing high contrasting images, therefore suggesting the method as a feasible alternative to the histological analysis of cell growth within tissue scaffolds. Copyright © 2011 IPEM. Published by Elsevier Ltd. All rights reserved.

  16. Geometrical Alignment of Multiple Fabrication Steps for Rapid Prototyping of Microfluidic Paper-Based Analytical Devices.

    Science.gov (United States)

    Rahbar, Mohammad; Nesterenko, Pavel N; Paull, Brett; Macka, Mirek

    2017-11-21

    Three main fabrication steps for microfluidic paper-based analytical devices (μPADs) were fully integrated with accurate geometrical alignment between the individual steps in a simple and rapid manner. A wax printer for creating hydrophobic barriers was integrated with an inexpensive (ca. $300) electronic craft plotter/cutter for paper cutting, followed by colorimetric reagent deposition using technical pens. The principal shortcoming in the lack of accurate and precise alignment of the features created by these three individual fabrication steps was addressed in this work by developing appropriate alignment procedures during the multistep fabrication process. The wax printing step was geometrically aligned with the following cutting and plotting (deposition) steps in a highly accurate and precise manner using optical scanning function of the plotter/cutter based on registration marks printed on the paper using the wax printer and scanned by the plotter/cutter. The accuracy and precision of alignment in a two-dimensional plane were quantified by cutting and plotting cross-shaped features and measuring their center coordinates relative to wax printed reference lines. The average accuracy along the X- and Y-axis was 0.12 and 0.16 mm for cutting and 0.19 and 0.17 mm for plotting, respectively. The potential of this approach was demonstrated by fabricating μPADs for instrument-free determination of cobalt in waters using distance-based readout, with excellent precision (%RSD = 5.7) and detection limit (LOD) of 2.5 ng and 0.5 mg/L (mass and concentration LODs, respectively).

  17. A prototype yarn evaluation tester to rapidly assess comparative weavability of warp yarns without weaving

    Science.gov (United States)

    The art of weaving continues to be the most predominantly used method of converting textile fibers into fabrics for various end-use applications, including apparel. In fact, the weaving is by far the largest textile manufacturing sector, worldwide. However, the weaving process is complex and costly....

  18. Rapid, low cost prototyping of transdermal devices for personal healthcare monitoring

    Directory of Open Access Journals (Sweden)

    Sanjiv Sharma

    2017-04-01

    We present here a minimally invasive microneedle array as a continuous monitoring platform technology. Method for scalable fabrication of these structures is presented. The microneedle arrays were characterised mechanically and were shown to penetrate human skin under moderate thumb pressure. They were then functionalised and evaluated as glucose, lactate and theophylline biosensors. The results suggest that this technology can be employed in the measurement of metabolites, therapeutic drugs and biomarkers and could have an important role to play in the management of chronic diseases.

  19. Innovative Approaches to Space-Based Manufacturing and Rapid Prototyping of Composite Materials

    Science.gov (United States)

    Hill, Charles S.

    2012-01-01

    The ability to deploy large habitable structures, construct, and service exploration vehicles in low earth orbit will be an enabling capability for continued human exploration of the solar system. It is evident that advanced manufacturing methods to fabricate replacement parts and re-utilize launch vehicle structural mass by converting it to different uses will be necessary to minimize costs and allow flexibility to remote crews engaged in space travel. Recent conceptual developments and the combination of inter-related approaches to low-cost manufacturing of composite materials and structures are described in context leading to the possibility of on-orbit and space-based manufacturing.

  20. Rapid Prototyping of Plastic Lab-on-a-Chip by Femtosecond Laser Micromachining and Removable Insert Microinjection Molding

    Directory of Open Access Journals (Sweden)

    Rebeca Martínez Vázquez

    2017-11-01

    Full Text Available We have introduced a new hybrid fabrication method for lab-on-a-chip devices through the combination of femtosecond laser micromachining and removable insert micro-injection molding. This method is particularly suited for the fast prototyping of new devices, while maintaining a competitive low cost. To demonstrate the effectiveness of our approach, we designed, fabricated, and tested a completely integrated flow cytometer coupled to a portable media device. The system operation was tested with fluorescent plastic micro-bead solutions ranging from 100 beads/μL to 500 beads/μL. We demonstrated that this hybrid lab-on-a-chip fabrication technology is suitable for producing low-cost and portable biological microsystems and for effectively bridging the gap between new device concepts and their mass production.

  1. PARTICIPATORY DESIGN OF PEDIATRIC UPPER LIMB PROSTHESES: QUALITATIVE METHODS AND PROTOTYPING.

    Science.gov (United States)

    Sims, Tara; Cranny, Andy; Metcalf, Cheryl; Chappell, Paul; Donovan-Hall, Maggie

    2017-09-06

    The study aims to develop an understanding of the views of children and adolescents, parents, and professionals on upper limb prosthetic devices to develop and improve device design. Previous research has found that children are dissatisfied with prostheses but has relied heavily on parent proxy reports and quantitative measures (such as questionnaires) to explore their views. Thirty-four participants (eight children aged 8-15 years with upper limb difference, nine parents, eight prosthetists, and nine occupational therapists) contributed to the development of new devices through the BRIDGE methodology of participatory design, using focus groups and interviews. The study identified areas for improving prostheses from the perspective of children and adolescents, developed prototypes based on these and gained feedback on the prototypes from the children and other stakeholders (parents and professionals) of paediatric upper limb prostheses. Future device development needs to focus on ease of use, versatility, appearance, and safety. This study has demonstrated that children and adolescents can and should be involved as equal partners in the development of daily living equipment and that rapid prototyping (three-dimensional printing or additive manufacturing), used within a participatory design framework, can be a useful tool for facilitating this.

  2. Rapid prototyping of 3D DNA-origami shapes with caDNAno

    Science.gov (United States)

    Douglas, Shawn M.; Marblestone, Adam H.; Teerapittayanon, Surat; Vazquez, Alejandro; Church, George M.; Shih, William M.

    2009-01-01

    DNA nanotechnology exploits the programmable specificity afforded by base-pairing to produce self-assembling macromolecular objects of custom shape. For building megadalton-scale DNA nanostructures, a long ‘scaffold’ strand can be employed to template the assembly of hundreds of oligonucleotide ‘staple’ strands into a planar antiparallel array of cross-linked helices. We recently adapted this ‘scaffolded DNA origami’ method to producing 3D shapes formed as pleated layers of double helices constrained to a honeycomb lattice. However, completing the required design steps can be cumbersome and time-consuming. Here we present caDNAno, an open-source software package with a graphical user interface that aids in the design of DNA sequences for folding 3D honeycomb-pleated shapes A series of rectangular-block motifs were designed, assembled, and analyzed to identify a well-behaved motif that could serve as a building block for future studies. The use of caDNAno significantly reduces the effort required to design 3D DNA-origami structures. The software is available at http://cadnano.org/, along with example designs and video tutorials demonstrating their construction. The source code is released under the MIT license. PMID:19531737

  3. Rapid, low cost prototyping of transdermal devices for personal healthcare monitoring.

    Science.gov (United States)

    Sharma, Sanjiv; Saeed, Anwer; Johnson, Christopher; Gadegaard, Nikolaj; Cass, Anthony Eg

    2017-04-01

    The next generation of devices for personal healthcare monitoring will comprise molecular sensors to monitor analytes of interest in the skin compartment. Transdermal devices based on microneedles offer an excellent opportunity to explore the dynamics of molecular markers in the interstitial fluid, however good acceptability of these next generation devices will require several technical problems associated with current commercially available wearable sensors to be overcome. These particularly include reliability, comfort and cost. An essential pre-requisite for transdermal molecular sensing devices is that they can be fabricated using scalable technologies which are cost effective. We present here a minimally invasive microneedle array as a continuous monitoring platform technology. Method for scalable fabrication of these structures is presented. The microneedle arrays were characterised mechanically and were shown to penetrate human skin under moderate thumb pressure. They were then functionalised and evaluated as glucose, lactate and theophylline biosensors. The results suggest that this technology can be employed in the measurement of metabolites, therapeutic drugs and biomarkers and could have an important role to play in the management of chronic diseases.

  4. SimITK: rapid ITK prototyping using the Simulink visual programming environment

    Science.gov (United States)

    Dickinson, A. W. L.; Mousavi, P.; Gobbi, D. G.; Abolmaesumi, P.

    2011-03-01

    The Insight Segmentation and Registration Toolkit (ITK) is a long-established, software package used for image analysis, visualization, and image-guided surgery applications. This package is a collection of C++ libraries, that can pose usability problems for users without C++ programming experience. To bridge the gap between the programming complexities and the required learning curve of ITK, we present a higher-level visual programming environment that represents ITK methods and classes by wrapping them into "blocks" within MATLAB's visual programming environment, Simulink. These blocks can be connected to form workflows: visual schematics that closely represent the structure of a C++ program. Due to the heavily C++ templated nature of ITK, direct interaction between Simulink and ITK requires an intermediary to convert their respective datatypes and allow intercommunication. We have developed a "Virtual Block" that serves as an intermediate wrapper around the ITK class and is responsible for resolving the templated datatypes used by ITK to native types used by Simulink. Presently, the wrapping procedure for SimITK is semi-automatic in that it requires XML descriptions of the ITK classes as a starting point, as this data is used to create all other necessary integration files. The generation of all source code and object code from the XML is done automatically by a CMake build script that yields Simulink blocks as the final result. An example 3D segmentation workflow using cranial-CT data as well as a 3D MR-to-CT registration workflow are presented as a proof-of-concept.

  5. Design and fabrication of standardized hydroxyapatite scaffolds with a defined macro-architecture by rapid prototyping for bone-tissue-engineering research

    NARCIS (Netherlands)

    Wilson, C.E.; Wilson, C.E.; de Bruijn, Joost Dick; van Blitterswijk, Clemens; Verbout, A.J.; Dhert, W.J.A.

    2004-01-01

    This investigation describes the production and characterization of calcium phosphate scaffolds with defined and reproducible porous macro-architectures and their preliminary in vitro and in vivo bone-tissue-engineered response. Fugitive wax molds were designed and produced using a rapid prototyping

  6. Plug-and-play paper-based toolkit for rapid prototyping of microfluidics and electronics towards point-of-care diagnostic solutions

    CSIR Research Space (South Africa)

    Smith, S

    2015-11-01

    Full Text Available -1 RAPDASA 2015 conference, Roodevallei, Pretoria, 4 - 6 November 2015 PLUG-AND-PLAY PAPER-BASED TOOLKIT FOR RAPID PROTOTYPING OF MICROFLUIDICS AND ELECTRONICS TOWARDS POINT-OF-CARE DIAGNOSTIC SOLUTIONS S. Smith1*, K. Moodley2 & K. Land3 1...

  7. Restoring masticatory function in a patient with severe microstomia using rapid prototyped mesh and a custom-made hinge and swing-lock prosthesis.

    Science.gov (United States)

    Tulunoglu, Ibrahim; Lee, Meng Huan; Taifur, Mohammed Louay; Tulunoglu, Ozlem

    2017-10-14

    This clinical report describes the use of rapid prototyped mesh in a complete swing-lock prosthesis to restore masticatory function in an edentulous patient with severe microstomia and perioral scar tissue after an industrial hot tar accident. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  8. Virtual reality surgical planning for maxillofacial distraction osteogenesis: the role of reverse engineering rapid prototyping and cooperative work.

    Science.gov (United States)

    Robiony, Massimo; Salvo, Iolanda; Costa, Fabio; Zerman, Nicoletta; Bazzocchi, Massimo; Toso, Francesco; Bandera, Camillo; Filippi, Stefano; Felice, Martina; Politi, Massimo

    2007-06-01

    The purpose of this article is the demonstration of virtual reality (VR) and rapid prototyping (RP) in surgical planning in maxillofacial surgery. The authors emphasize the role of reverse engineering (RE) and RP, suggesting a model of cooperative work, with the interaction of maxillofacial surgeons, radiologists, and engineers. Data acquisition is performed using computed tomography. The 3D model is the result of RE practices based on image segmentation, and the real model is produced via stereolithography. Virtual simulations are performed on the 3D model obtained from image segmentation. All these stages require the interaction and collaboration of various experts: maxillofacial surgeons, radiologists, and RE and RP experts. VR and stereolithography models represent a new technology to help the surgeon who has to work in cooperation with engineers and radiologists to improve the results in surgical planning of maxillofacial distraction. When performing the VR simulation, surgeons and engineers operate together in order to optimize the exploitation of the instruments available. Both VR and RP, with different and complementary advantages and limitations, can improve surgical planning activities and this is particularly effective when dealing with complex anatomical structures in maxillofacial surgery.

  9. Innovative procedure for computer-assisted genioplasty: three-dimensional cephalometry, rapid-prototyping model and surgical splint.

    Science.gov (United States)

    Olszewski, R; Tranduy, K; Reychler, H

    2010-07-01

    The authors present a new procedure of computer-assisted genioplasty. They determined the anterior, posterior and inferior limits of the chin in relation to the skull and face with the newly developed and validated three-dimensional cephalometric planar analysis (ACRO 3D). Virtual planning of the osteotomy lines was carried out with Mimics (Materialize) software. The authors built a three-dimensional rapid-prototyping multi-position model of the chin area from a medical low-dose CT scan. The transfer of virtual information to the operating room consisted of two elements. First, the titanium plates on the 3D RP model were pre-bent. Second, a surgical guide for the transfer of the osteotomy lines and the positions of the screws to the operating room was manufactured. The authors present the first case of the use of this model on a patient. The postoperative results are promising, and the technique is fast and easy-to-use. More patients are needed for a definitive clinical validation of this procedure. Copyright 2010 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  10. Simultaneous repair of two large cranial defects using rapid prototyping and custom computer-designed titanium plates: a case report.

    Science.gov (United States)

    Morrison, D A; Guy, D T; Day, R E; Lee, G Y F

    2011-11-01

    Custom titanium cranioplasty plates, manufactured by a variety of techniques, have been used to repair a range of cranial defects. The authors present a case where two relatively large, adjacent cranial defects were repaired by custom computer-designed titanium plates. The two plates were designed and fabricated simultaneously using a unique methodology. A 28-year-old woman underwent a corpus callosotomy for medically intractable epilepsy. The surgery was complicated by unexpected haemorrhage which necessitated a second craniotomy. Subsequent deep infection required the removal of bilateral bone flaps, presenting a challenge in the reconstruction of extensive, bilateral but asymmetrical cranial defects. The patient underwent a head computed tomography scan, from which a rapid-prototype model of the skull was produced. The surfaces for the missing cranial segments were generated virtually using a combination of software products and two titanium plates that followed these virtual contours were manufactured to cover the defects. The cranioplasty procedure to implant both titanium cranial plates was performed efficiently with no intra-operative complications. Intra-operatively, an excellent fit was achieved. The careful planning of the plates enhanced the relative ease with which the cranial defects were repaired with an excellent cosmetic outcome.

  11. Scaffolds for bone tissue engineering fabricated from two different materials by the rapid prototyping technique: PCL versus PLGA.

    Science.gov (United States)

    Park, So Hee; Park, Dae Sung; Shin, Ji Won; Kang, Yun Gyeong; Kim, Hyung Keun; Yoon, Taek Rim; Shin, Jung-Woog

    2012-11-01

    Three dimensional tissue engineered scaffolds for the treatment of critical defect have been usually fabricated by salt leaching or gas forming technique. However, it is not easy for cells to penetrate the scaffolds due to the poor interconnectivity of pores. To overcome these current limitations we utilized a rapid prototyping (RP) technique for fabricating tissue engineered scaffolds to treat critical defects. The RP technique resulted in the uniform distribution and systematic connection of pores, which enabled cells to penetrate the scaffold. Two kinds of materials were used. They were poly(ε-caprolactone) (PCL) and poly(D, L-lactic-glycolic acid) (PLGA), where PCL is known to have longer degradation time than PLGA. In vitro tests supported the biocompatibility of the scaffolds. A 12-week animal study involving various examinations of rabbit tibias such as micro-CT and staining showed that both PCL and PLGA resulted in successful bone regeneration. As expected, PLGA degraded faster than PCL, and consequently the tissues generated in the PLGA group were less dense than those in the PCL group. We concluded that slower degradation is preferable in bone tissue engineering, especially when treating critical defects, as mechanical support is needed until full regeneration has occurred.

  12. Deep Proton Writing for the rapid prototyping of polymer micro-components for optical interconnects and optofluidics

    Science.gov (United States)

    Van Erps, Jürgen; Vervaeke, Michael; Ottevaere, Heidi; Hermanne, Alex; Thienpont, Hugo

    2013-07-01

    The use of photonics in data communication and numerous other industrial applications brought plenty of prospects for innovation and opened up different unexplored market opportunities. This is a major driving force for the fabrication of micro-optical and micro-mechanical structures and their accurate alignment and integration into opto-mechanical modules and systems. To this end, we present Deep Proton Writing (DPW) as a powerful rapid prototyping technology for such micro-components. The DPW process consists of bombarding polymer samples (PMMA or SU-8) with swift protons, which results after chemical processing steps in high-quality micro-optical components. One of the strengths of the DPW micro-fabrication technology is the ability to fabricate monolithic building blocks that include micro-optical and mechanical functionalities which can be precisely integrated into more complex photonic systems. In this paper we comment on how we shifted from using 8.3 to 16.5 MeV protons for DPW and give some examples of micro-optical and micro-mechanical components recently fabricated through DPW, targeting applications in optical interconnections and in optofluidics.

  13. Rapid Tooling for Functional Prototype of Metal Mold Processes Final Report CRADA No. TC-1032-98

    Energy Technology Data Exchange (ETDEWEB)

    Heestand, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jaskolski, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-10-16

    Production inserts for die-casting were generally fabricated from materials with sufficient strength and· good wear properties at casting temperatures for long life. Frequently tool steels were used and machining was done with a combination of. conventional and Electric Discharge Machining (EDM) with some handwork, an expensive and time consuming process, partilly for prototype work. We proposed electron beam physical vapor deposition (EBPVD) as a process for rapid fabrication of dies. Metals, ranging from low melting point to refractory metals (Ta, Mo, etc.), would be evaporated and deposited at high rates (-2mm/hr.). Alloys could be easily evaporated and deposited if their constituent vapor pressures were similar and with more difficulty if they were not. Of course, layering of different materials was possible if required for a specific application. For example, a hard surface layer followed by a tough steel and backed by a high thermal conductivity (possibly cooled) copper layer could be fabricated. Electron-beam deposits exhibited 100% density and lull strength when deposited at a substrate (mandrel) temperature that was a substantial fraction of the deposited material's melting point. There were several materials that could have the required high temperature properties and ease of fabrication required for such a mandrel. We had successfully used graphite, machined from free formed objects with a replicator, to produce aluminum-bronze test molds. There were several parting layer materials of interest, but the ideal material depended upon the specific application.

  14. ASSESSMENT OF SURFACE FINISH AND DIMENSIONAL ACCURACY OF TOOLS MANUFACTURED BY METAL CASTING IN RAPID PROTOTYPING SAND MOULDS

    Directory of Open Access Journals (Sweden)

    Nyembwe, K.

    2012-11-01

    Full Text Available In this paper, an initial assessment of the quality parameters of the surface finish and dimensional accuracy of tools made by metal casting in rapid prototyping (RP sand moulds is undertaken. A case study from a local tool room, dealing with the manufacturing of an aluminium die for the lost wax process, is employed. Modern techniques, including surface roughness analysis and three dimensional scanning, are used to determine and understand how each manufacturing step influences the final quality of the cast tool. The best surface finish obtained for the cast die had arithmetic average roughness (Ra and mean average roughness (Rz respectively equal to 3.23m and 11.38m. In terms of dimensional accuracy, 82% of cast-die points coincided with the Computer Aided Design (CAD data, which is within the typical tolerances of sand cast products. The investigation shows that mould coating contributes slightly to the improvement of the cast tool surface finish. The study also found that the additive manufacturing of the sand mould was the chief factor responsible for the loss of dimensional accuracy. These findings indicate that machining will always be required to improve the surface finish and the dimensional accuracy of cast tools in RP sand moulds.

  15. Preliminary Clinical Application of Removable Partial Denture Frameworks Fabricated Using Computer-Aided Design and Rapid Prototyping Techniques.

    Science.gov (United States)

    Ye, Hongqiang; Ning, Jing; Li, Man; Niu, Li; Yang, Jian; Sun, Yuchun; Zhou, Yongsheng

    The aim of this study was to explore the application of computer-aided design and rapid prototyping (CAD/RP) for removable partial denture (RPD) frameworks and evaluate the fitness of the technique for clinical application. Three-dimensional (3D) images of dentition defects were obtained using a lab scanner. The RPD frameworks were designed using commercial dental software and manufactured using selective laser melting (SLM). A total of 15 cases of RPD prostheses were selected, wherein each patient received two types of RPD frameworks, prepared by CAD/RP and investment casting. Primary evaluation of the CAD/RP framework was performed by visual inspection. The gap between the occlusal rest and the relevant rest seat was then replaced using silicone, and the specimens were observed and measured. Paired t test was used to compare the average thickness and distributed thickness between the CAD/RP and investment casting frameworks. Analysis of variance test was used to compare the difference in thickness among different zones. The RPD framework was designed and directly manufactured using the SLM technique. CAD/RP frameworks may meet the clinical requirements with satisfactory retention and stability and no undesired rotation. Although the average gap between the occlusal rest and the corresponding rest seat of the CAD/RP frameworks was slightly larger than that of the investment casting frameworks (P < .05), it was acceptable for clinical application. RPD frameworks can be designed and fabricated directly using digital techniques with acceptable results in clinical application.

  16. Deep Proton Writing for the rapid prototyping of polymer micro-components for optical interconnects and optofluidics

    Energy Technology Data Exchange (ETDEWEB)

    Van Erps, Jürgen, E-mail: jurgen.van.erps@vub.ac.be; Vervaeke, Michael; Ottevaere, Heidi; Hermanne, Alex; Thienpont, Hugo

    2013-07-15

    The use of photonics in data communication and numerous other industrial applications brought plenty of prospects for innovation and opened up different unexplored market opportunities. This is a major driving force for the fabrication of micro-optical and micro-mechanical structures and their accurate alignment and integration into opto-mechanical modules and systems. To this end, we present Deep Proton Writing (DPW) as a powerful rapid prototyping technology for such micro-components. The DPW process consists of bombarding polymer samples (PMMA or SU-8) with swift protons, which results after chemical processing steps in high-quality micro-optical components. One of the strengths of the DPW micro-fabrication technology is the ability to fabricate monolithic building blocks that include micro-optical and mechanical functionalities which can be precisely integrated into more complex photonic systems. In this paper we comment on how we shifted from using 8.3 to 16.5 MeV protons for DPW and give some examples of micro-optical and micro-mechanical components recently fabricated through DPW, targeting applications in optical interconnections and in optofluidics.

  17. Fabrication of novel Si-doped hydroxyapatite/gelatine scaffolds by rapid prototyping for drug delivery and bone regeneration.

    Science.gov (United States)

    Martínez-Vázquez, F J; Cabañas, M V; Paris, J L; Lozano, D; Vallet-Regí, M

    2015-03-01

    Porous 3-D scaffolds consisting of gelatine and Si-doped hydroxyapatite were fabricated at room temperature by rapid prototyping. Microscopic characterization revealed a highly homogeneous structure, showing the pre-designed porosity (macroporosity) and a lesser in-rod porosity (microporosity). The mechanical properties of such scaffolds are close to those of trabecular bone of the same density. The biological behavior of these hybrid scaffolds is greater than that of pure ceramic scaffolds without gelatine, increasing pre-osteoblastic MC3T3-E1 cell differentiation (matrix mineralization and gene expression). Since the fabrication process of these structures was carried out at mild conditions, an antibiotic (vancomycin) was incorporated in the slurry before the extrusion of the structures. The release profile of this antibiotic was measured in phosphate-buffered saline solution by high-performance liquid chromatography and was adjusted to a first-order release kinetics. Vancomycin released from the material was also shown to inhibit bacterial growth in vitro. The implications of these results for bone tissue engineering applications are discussed. Copyright © 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  18. Human Adipose-Derived Stem Cells on Rapid Prototyped Three-Dimensional Hydroxyapatite/Beta-Tricalcium Phosphate Scaffold.

    Science.gov (United States)

    Canciani, Elena; Dellavia, Claudia; Ferreira, Lorena Maria; Giannasi, Chiara; Carmagnola, Daniela; Carrassi, Antonio; Brini, Anna Teresa

    2016-05-01

    In the study, we assess a rapid prototyped scaffold composed of 30/70 hydroxyapatite (HA) and beta-tricalcium-phosphate (β-TCP) loaded with human adipose-derived stem cells (hASCs) to determine cell proliferation, differentiation toward osteogenic lineage, adhesion and penetration on/into the scaffold.In this in vitro study, hASCs isolated from fat tissue discarded after plastic surgery were expanded, characterized, and then loaded onto the scaffold. Cells were tested for: viability assay (Alamar Blue at days 3, 7 and Live/Dead at day 32), differentiation index (alkaline phosphatase activity at day 14), scaffold adhesion (standard error of the mean analysis at days 5 and 18), and penetration (ground sections at day 32).All the hASC populations displayed stemness markers and the ability to differentiate toward adipogenic and osteogenic lineages.Cellular vitality increased between 3 and 7 days, and no inhibitory effect by HA/β-TCP was observed. Under osteogenic stimuli, scaffold increased alkaline phosphatase activity of +243% compared with undifferentiated samples. Human adipose-derived stem cells adhered on HA/β-TCP surface through citoplasmatic extensions that occupied the macropores and built networks among them. Human adipose derived stem cells were observed in the core of HA/β-TCP. The current combination of hASCs and HA/β-TCP scaffold provided encouraging results. If authors' data will be confirmed in preclinical models, the present engineering approach could represent an interesting tool in treating large bone defects.

  19. THE USE OF THE PATENT ANALYSIS METHOD FOR FINDING ANALOGUES AND PROTOTYPES OF RECEIVED TECHNICAL SOLUTIONS

    Directory of Open Access Journals (Sweden)

    Irina Petrova

    2016-03-01

    Full Text Available The research deals with the issue of the patent analysis efficiency, which is a necessary stage of seaching analogues and prototypes to obtain technical solutions. The article presents the results of analyzing the present automation systems for finding necessary information in the patent databases and identifies their advantages and disadvantages. It gives a description of the “Intellect” system, which is an example of software systems for the conceptual design stage support. Materials and Methods The article presents some of the possible ways to organize the patents-analogues search process and specific features of searching analogues and prototypes for the generated parametric structure scheme of the technical solution, which is the result of the synthesis of a new information-measuring and control system element in the “Intellect” system. The description of the proposed search query forming method is given. The article gives the structure of the patent passport, which must be stored in a database to organize the process of searcing analogues and prototypes. There given a description of algorithms for automatic adding a patent to the database, recalculating the weights while adding a patent by experts, identifying the fact of using different physical and technical effects in a patent. Results The final part of the article contains an example of the results of testing the developed subsystem implementing the proposed method. According to the test results it is concluded that the selected software and algorithmic solutions are effective.

  20. Rapid method for detection of salmonella in meat

    DEFF Research Database (Denmark)

    2016-01-01

    The present invention relates to a rapid method for the detection of Salmonella in meat as well as to a kit for performing said method. The method provides a time-to-result of less than 8 hours.......The present invention relates to a rapid method for the detection of Salmonella in meat as well as to a kit for performing said method. The method provides a time-to-result of less than 8 hours....

  1. Methods and compositions for rapid thermal cycling

    Science.gov (United States)

    Beer, Neil Reginald; Benett, William J.; Frank, James M.; Deotte, Joshua R.; Spadaccini, Christopher

    2015-10-27

    The rapid thermal cycling of a material is targeted. A microfluidic heat exchanger with an internal porous medium is coupled to tanks containing cold fluid and hot fluid. Fluid flows alternately from the cold tank and the hot tank into the porous medium, cooling and heating samples contained in the microfluidic heat exchanger's sample wells. A valve may be coupled to the tanks and a pump, and switching the position of the valve may switch the source and direction of fluid flowing through the porous medium. A controller may control the switching of valve positions based on the temperature of the samples and determined temperature thresholds. A sample tray for containing samples to be thermally cycled may be used in conjunction with the thermal cycling system. A surface or internal electrical heater may aid in heating the samples, or may replace the necessity for the hot tank.

  2. Application of 3D printing rapid prototyping-assisted percutaneous fixation in the treatment of intertrochanteric fracture.

    Science.gov (United States)

    Zheng, Sheng-Nai; Yao, Qing-Qiang; Mao, Feng-Yong; Zheng, Peng-Fei; Tian, Shu-Chang; Li, Jia-Yi; Yu, Yi-Fan; Liu, Shuai; Zhou, Jin; Hu, Jun; Xu, Yan; Tang, Kai; Lou, Yue; Wang, Li-Ming

    2017-10-01

    The aim of the present study was to investigate the application of 3D printing (3DP) rapid prototyping (RP) technique-assisted percutaneous fixation in the treatment of femoral intertrochanteric fracture (ITF) using proximal femoral nail anti-rotation (PFNA). A total of 39 patients with unstable ITF were included in the current study. Patients were divided into two groups: 19 patients were examined using computed tomography scanning and underwent PFNA with SDP-RP whereas the other 20 patients underwent conventional PFNA treatment. Anatomical data were converted from the Digital Imaging and Communications in Medicine format to the stereolithography format using M3D software. The 3DP-RP model was established using the fused deposition modeling technique and the length and diameter of the main screw blade was measured during the simulation. The postoperative femoral neck-shaft angle (NSA), surgery duration, intraoperative and postoperative blood loss, and the duration of hospital stay were recorded and compared with the corresponding values in conventional surgery. No significant differences were observed in mean PFNA size between the implants used and the preoperative planning estimates. It was demonstrated that the 3DP-RP assisted procedure resulted in more effective reduction of the NSA. Furthermore, patients undergoing 3DP-RP experienced a significant reduction in duration of surgery (P<0.01), as well as reductions in intraoperative (P=0.02) and postoperative (P=0.03) blood loss, compared with conventional surgery. At 6 months post-surgery, no cases of hip varus/vague deformities or implant failure were observed in patients that underwent either the 3DP-RP-assisted or conventional procedure. The results of the present study suggest that the 3DP-RP technique is able to create an accurate model of the ITF, which facilitates surgical planning and fracture reduction, thus improving the efficiency of PFNA surgery for ITFs.

  3. Replacing Heavily Damaged Teeth by Third Molar Autotransplantation With the Use of Cone-Beam Computed Tomography and Rapid Prototyping.

    Science.gov (United States)

    Verweij, Jop P; Anssari Moin, David; Wismeijer, Daniel; van Merkesteyn, J P Richard

    2017-09-01

    This article describes the autotransplantation of third molars to replace heavily damaged premolars and molars. Specifically, this article reports on the use of preoperative cone-beam computed tomographic planning and 3-dimensional (3D) printed replicas of donor teeth to prepare artificial tooth sockets. In the present case, an 18-year-old patient underwent autotransplantation of 3 third molars to replace 1 premolar and 2 molars that were heavily damaged after trauma. Approximately 1 year after the traumatic incident, autotransplantation with the help of 3D planning and rapid prototyping was performed. The right maxillary third molar replaced the right maxillary first premolar. The 2 mandibular wisdom teeth replaced the left mandibular first and second molars. During the surgical procedure, artificial tooth sockets were prepared with the help of 3D printed donor tooth copies to prevent iatrogenic damage to the actual donor teeth. These replicas of the donor teeth were designed based on the preoperative cone-beam computed tomogram and manufactured with the help of 3D printing techniques. The use of a replica of the donor tooth resulted in a predictable and straightforward procedure, with extra-alveolar times shorter than 2 minutes for all transplantations. The transplanted teeth were placed in infraocclusion and fixed with a suture splint. Postoperative follow-up showed physiologic integration of the transplanted teeth and a successful outcome for all transplants. In conclusion, this technique facilitates a straightforward and predictable procedure for autotransplantation of third molars. The use of printed analogues of the donor teeth decreases the risk of iatrogenic damage and the extra-alveolar time of the transplanted tooth is minimized. This facilitates a successful outcome. Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

  4. Low Cost Rapid Response Spacecraft, (LCRRS): A Research Project in Low Cost Spacecraft Design and Fabrication in a Rapid Prototyping Environment

    Science.gov (United States)

    Spremo, Stevan; Bregman, Jesse; Dallara, Christopher D.; Ghassemieh, Shakib M.; Hanratty, James; Jackson, Evan; Kitts, Christopher; Klupar, Pete; Lindsay, Michael; Ignacio, Mas; hide

    2009-01-01

    The Low Cost Rapid Response Spacecraft (LCRRS) is an ongoing research development project at NASA Ames Research Center (ARC), Moffett Field, California. The prototype spacecraft, called Cost Optimized Test for Spacecraft Avionics and Technologies (COTSAT) is the first of what could potentially be a series of rapidly produced low-cost satellites. COTSAT has a target launch date of March 2009 on a SpaceX Falcon 9 launch vehicle. The LCRRS research system design incorporates use of COTS (Commercial Off The Shelf), MOTS (Modified Off The Shelf), and GOTS (Government Off The Shelf) hardware for a remote sensing satellite. The design concept was baselined to support a 0.5 meter Ritchey-Chretien telescope payload. This telescope and camera system is expected to achieve 1.5 meter/pixel resolution. The COTSAT team is investigating the possibility of building a fully functional spacecraft for $500,000 parts and $2,000,000 labor. Cost is dramatically reduced by using a sealed container, housing the bus and payload subsystems. Some electrical and RF designs were improved/upgraded from GeneSat-1 heritage systems. The project began in January 2007 and has yielded two functional test platforms. It is expected that a flight-qualified unit will be finished in December 2008. Flight quality controls are in place on the parts and materials used in this development with the aim of using them to finish a proto-flight satellite. For LEO missions the team is targeting a mission class requiring a minimum of six months lifetime or more. The system architecture incorporates several design features required by high reliability missions. This allows for a true skunk works environment to rapidly progress toward a flight design. Engineering and fabrication is primarily done in-house at NASA Ames with flight certifications on materials. The team currently employs seven Full Time Equivalent employees. The success of COTSATs small team in this effort can be attributed to highly cross trained

  5. CAD/CAM and rapid prototyped scaffold construction for bone regenerative medicine and surgical transfer of virtual planning: a pilot study.

    Science.gov (United States)

    Ciocca, L; De Crescenzio, F; Fantini, M; Scotti, R

    2009-01-01

    We developed a model to test new bone constructs to replace spare skeletal segments originating from new generation scaffolds for bone marrow-derived mesenchymal stem cells. Using computed tomography (CT) data, scaffolds were defined using computer-aided design/computer-aided manufacturing (CAD/CAM) for rapid prototyping by three-dimensional (3D) printing. A bone defect was created in pig mandible ramus by condyle resection for CT and CAD/CAM elaboration of bone volume for cutting and scaffold restoration. The protocol produced a perfect-fitting bone substitute model for rapid prototyped hydroxyapatite (HA) scaffolds. A surgical guide system was developed to accurately reproduce virtually planned bone sectioning procedures in animal models to obtain a perfect fit during surgery.

  6. Indirect rapid prototyping of sol-gel hybrid glass scaffolds for bone regeneration - Effects of organic crosslinker valence, content and molecular weight on mechanical properties.

    Science.gov (United States)

    Hendrikx, Stephan; Kascholke, Christian; Flath, Tobias; Schumann, Dirk; Gressenbuch, Mathias; Schulze, F Peter; Hacker, Michael C; Schulz-Siegmund, Michaela

    2016-04-15

    We present a series of organic/inorganic hybrid sol-gel derived glasses, made from a tetraethoxysilane-derived silica sol (100% SiO2) and oligovalent organic crosslinkers functionalized with 3-isocyanatopropyltriethoxysilane. The material was susceptible to heat sterilization. The hybrids were processed into pore-interconnected scaffolds by an indirect rapid prototyping method, described here for the first time for sol-gel glass materials. A large panel of polyethylene oxide-derived 2- to 4-armed crosslinkers of molecular weights ranging between 170 and 8000Da were incorporated and their effect on scaffold mechanical properties was investigated. By multiple linear regression, 'organic content' and the 'content of ethylene oxide units in the hybrid' were identified as the main factors that determined compressive strength and modulus, respectively. In general, 3- and 4-armed crosslinkers performed better than linear molecules. Compression tests and cell culture experiments with osteoblast-like SaOS-2 cells showed that macroporous scaffolds can be produced with compressive strengths of up to 33±2MPa and with a pore structure that allows cells to grow deep into the scaffolds and form mineral deposits. Compressive moduli between 27±7MPa and 568±98MPa were obtained depending on the hybrid composition and problems associated with the inherent brittleness of sol-gel glass materials could be overcome. SaOS-2 cells showed cytocompatibility on hybrid glass scaffolds and mineral accumulation started as early as day 7. On day 14, we also found mineral accumulation on control hybrid glass scaffolds without cells, indicating a positive effect of the hybrid glass on mineral accumulation. We produced a hybrid sol-gel glass material with significantly improved mechanical properties towards an application in bone regeneration and processed the material into macroporous scaffolds of controlled architecture by indirect rapid prototyping. We were able to produce macroporous materials

  7. A new method for nocturnal aerosol measurements with a lunar photometer prototype

    Directory of Open Access Journals (Sweden)

    A. Barreto

    2013-03-01

    Full Text Available This paper presents the preliminary results of nocturnal Aerosol Optical Depth (τa and Angström Exponent (α obtained from a new lunar photometer prototype, trade name Cimel CE-318U. Due to the variation of the moon's illumination inherent to the lunar cycle, the typical Langley-plot Method used in solar photometry to calibrate these instruments cannot be applied. In this paper, we propose three different methods to carry out the lunar-photometer calibration. In order to validate the results, we have selected three events which encompass seven nights and ten days under different atmospheric conditions, including several saharan dust intrusions episodes. Method#1 is introduced in this work as a modification of the usual Langley Method. This technique, called Lunar-Langley Method, requires the extraterrestrial irradiances from a lunar irradiance model, providing similar accuracies on τa to those of AERONET (±0.01–0.02. It makes comparable daytime and nighttime measurements. Method#2 consists of transferring the current calibration from a master used by sunphotometers. Its results are again within the limit of accuracy expected for the instrument. Method#3 uses an integrating sphere and the methodology proposed by Li et al. (2008 to determine sky calibration coefficients (Cj and the instrument's solid angle field-of-view (Ω, respectively. We observe significant τa differences between Method#1 and #3 (up to 0.07, which might be attributed to the errors propagation in Method#3. The good results obtained from the comparison against a second CE-318U prototype, and against daytime data from a Precision Filter Radiometer (PFR, constitute a valuable assessment of CE-318U performance. Results of α and its spectral variation (δ α show good agreement between daytime and nighttime, being able to identify the aerosol properties associated with each event.

  8. Obtention of hydroxyapatite submicrometric of bovine origin by vibratory grinding for rapid prototyping; Obtencao de hidroxiapatita submicrometrica de origem bovina por moagem vibratoria visando prototipagem rapida

    Energy Technology Data Exchange (ETDEWEB)

    Meira, C.R.; Purquerio, B.M.; Fortulan, C.A., E-mail: camilameira@sc.usp.br [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Escola de Engenharia; Braga, F.J.C. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    Submicron bovine hydroxyapatite was obtained for rapid prototyping. Hydroxyapatite structure originated from bovine mineral bone has great importance among the biomaterials and biocompatibility due to its great similarity with the human bone structure. This study aims to obtain powder for manufacture by rapid prototyping of scaffolds. This technique manufacture requires highly reactive powders to compensate for the absence of pressure forming. Hydroxyapatite was milled in a ball mill and vibratory mill, and analyzed for their average equivalent spherical diameter and surface area. Test specimens were isostatically pressed at 100 MPa and machined into cylindrical test specimens. These specimens were sintered at several temperatures to determine the optimal sintering temperature based on densification and chemistry stability. In grinding ball mill was obtained particles of equivalent diameter of 0.74 micron in vibratory mill of 0.46 micrometers. An average flexural strength of 100 MPa and 99,8% of real density was attained for the sample sintered at 1300 deg C/2h, signaling potential for use in rapid prototyping. (author)

  9. Application of 3D rapid prototyping technology in posterior corrective surgery for Lenke 1 adolescent idiopathic scoliosis patients.

    Science.gov (United States)

    Yang, Mingyuan; Li, Chao; Li, Yanming; Zhao, Yingchuan; Wei, Xianzhao; Zhang, Guoyou; Fan, Jianping; Ni, Haijian; Chen, Ziqiang; Bai, Yushu; Li, Ming

    2015-02-01

    A retrospective study to evaluate the effectiveness of 3-dimensional rapid prototyping (3DRP) technology in corrective surgery for Lenke 1 adolescent idiopathic scoliosis (AIS) patients. 3DRP technology has been widely used in medical field; however, no study has been performed on the effectiveness of 3DRP technology in corrective surgery for Lenke 1 AIS patients. Lenke 1 AIS patients who were preparing to undergo posterior corrective surgery from a single center between January 2010 and January 2012 were included in this analysis. Patients were divided into 2 groups. In group A, 3-dimensional (3D) printing technology was used to create subject-specific spine models in the preoperative planning process. Group B underwent posterior corrective surgery as usual (by free hand without image guidance). Perioperative and postoperative clinical outcomes were compared between 2 groups, including operation time, perioperative blood loss, transfusion volume, postoperative hemoglobin (Hb), postoperative complications, and length of hospital stay. Radiological outcomes were also compared, including the assessment of screw placement, postoperative Cobb angle, coronal balance, sagittal vertical axis, thoracic kyphosis, and lumbar lordosis. Subgroup was also performed according to the preoperative Cobb angle: mean Cobb angle Cobb angle >50°. Besides, economic evaluation was also compared between 2 groups. A total of 126 patients were included in this study (group A, 50 and group B, 76). Group A had significantly shorter operation time, significantly less blood loss and transfusion volume, and higher postoperative Hb (all, P 0.05). There was also no significant difference in misplacement of screws in total populations (16.90% vs 18.82%, P = 0.305), whereas a low misplacement rate of pedicle screws was observed in patients whose mean Cobb angle was >50° (9.15% vs 13.03%, P = 0.02). Besides, using 3DRP increased the economic burden of patients (157,000 ± 9948.85

  10. Shaping ability of Reciproc and TF Adaptive systems in severely curved canals of rapid microCT-based prototyping molar replicas

    Directory of Open Access Journals (Sweden)

    Ronald ORDINOLA-ZAPATA

    2014-12-01

    Full Text Available Objective: To evaluate the shaping ability of Reciproc and Twisted-File Adaptive systems in rapid prototyping replicas. Material and Methods: Two mandibular molars showing S-shaped and 62-degree curvatures in the mesial root were scanned by using a microcomputed tomography (μCT system. The data were exported in the stereolitograhic format and 20 samples of each molar were printed at 16 µm resolution. The mesial canals of 10 replicas of each specimen were prepared with each system. Transportation was measured by overlapping radiographs taken before and after preparation and resin thickness after instrumentation was measured by μCT. Results: Both systems maintained the original shape of the apical third in both anatomies (P>0.05. Overall, considering the resin thickness in the 62-degree replicas, no statistical difference was found between the systems (P>0.05. In the S-shaped curvature replica, Reciproc significantly decreased the thickness of the resin walls in comparison with TF Adaptive. Conclusions: The evaluated systems were able to maintain the original shape at the apical third of severely curved mesial canals of molar replicas.

  11. Effects of carbon fibres on the life cycle assessment of additively manufactured injection moulding inserts for rapid prototyping

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Bey, Niki; Mischkot, Michael

    2017-01-01

    properties and lifetime. The additively manufactured inserts are compared to the standard materials steel, aluminium and brass. The investigated part of the production and prototyping phase considers the insert itself, the moulded part, and resulting waste material of the injection moulding process....

  12. Application of Rapid Prototyping to the Investment Casting of Test Hardware (MSFC Center Director's Discretionary Fund Final Report, Project No. 98-08)

    Science.gov (United States)

    Cooper, K. G.; Wells, D.

    2000-01-01

    Investment casting masters of a selected propulsion hardware component, a fuel pump housing, were rapid prototyped on the several processes in-house, along with the new Z-Corp process acquired through this project. Also, tensile samples were prototyped and cast using the same significant parameters. The models were then shelled in-house using a commercial grade zircon-based slurry and stucco technique. Next, the shelled models were fired and cast by our in-house foundry contractor (IITRI), with NASA-23, a commonly used test hardware metal. The cast models are compared by their surface finish and overall appearance (i.e., the occurrence of pitting, warping, etc.), as well as dimensional accuracy.

  13. AVSynDEx: A Rapid Prototyping Process Dedicated to the Implementation of Digital Image Processing Applications on Multi-DSP and FPGA Architectures

    Directory of Open Access Journals (Sweden)

    Virginie Fresse

    2002-09-01

    Full Text Available We present AVSynDEx (concatenation of AVS + SynDEx, a rapid prototyping process aiming to the implementation of digital signal processing applications on mixed architectures (multi-DSP + FPGA. This process is based on the use of widely available and efficient CAD tools established along the design process so that most of the implementation tasks become automatic. These tools and architectures are judiciously selected and integrated during the implementation process to help a signal processing specialist without relevant hardware experience. We have automated the translation between the different levels of the process to increase and secure it. One main advantage is that only a signal processing designer is needed, all the other specialized manual tasks being transparent in this prototyping methodology, hereby reducing the implementation time.

  14. Integrated Use of Tools and Technologies for Rapidly Prototyping Simulated Data Products of Future NASA Observing Systems For Evaluation in Applications of National Importance

    Science.gov (United States)

    O'Hara, C. G.; Moorhead, R.; Shaw, D.; Shrestha, B.; Ross, K.; Prados, D.; Russell, J.; Ryan, R. E.

    2006-12-01

    NASA sponsored "Rapid Prototyping Capability" (RPC) research activities of the Mississippi Research Consortium are aimed at developing infrastructure and experiments to evaluate data products from future NASA observing systems in applications, models or decision support tools of national importance. The RPC will host a wide variety of experiments, many of which will require the simulation of data streams to approximate products from future NASA observing systems. To simulate data from a future observing system, a variety of tools and technologies must be employed in an integrated computational workflow. Future data product simulations will typically involve using data products from currently operational science data mission observing systems to provide inputs to a process wherein data will be extracted and manipulated to provide products that approximate the spectral, spatial, radiometric, and temporal characteristics of planned future sensors. The integration of tools and technologies and adapting interfaces for ease of use will enable researchers to test a variety of simulations to efficiently determine an acceptable set of procedures whereby a simulated data product may be derived from existing data sources. Interactive research and testing of data product simulation scenarios will strongly leverage NASA tools and technologies such as the HDF Extraction to GeoTiff tool (HEG2.7) to extract large volumes of data in batch mode, the Time-Series Product Toolkit (TSPT) to evaluate methods for data fusion, de-noising, and creating multi-temporal composites, and the Application Research Toolbox (ART) to manipulate data product characteristics in the simulation process. Given an accepted simulation configuration generated by a set of methods and a documented process workflow, the process will be computationally implemented using Mississippi State University's Temporal Map Algebra (TMA) tools which will enable handling large data sets, computing efficiently the desired

  15. RAPID METHOD FOR DETERMINATION OF RADIOSTRONTIUM IN EMERGENCY MILK SAMPLES

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, S.; Culligan, B.

    2008-07-17

    A new rapid separation method for radiostrontium in emergency milk samples was developed at the Savannah River Site (SRS) Environmental Bioassay Laboratory (Aiken, SC, USA) that will allow rapid separation and measurement of Sr-90 within 8 hours. The new method uses calcium phosphate precipitation, nitric acid dissolution of the precipitate to coagulate residual fat/proteins and a rapid strontium separation using Sr Resin (Eichrom Technologies, Darien, IL, USA) with vacuum-assisted flow rates. The method is much faster than previous method that use calcination or cation exchange pretreatment, has excellent chemical recovery, and effectively removes beta interferences. When a 100 ml sample aliquot is used, the method has a detection limit of 0.5 Bq/L, well below generic emergency action levels.

  16. Applying RP-FDM Technology to Produce Prototype Castings Using the Investment Casting Method

    Directory of Open Access Journals (Sweden)

    Macků M.

    2012-09-01

    Full Text Available The research focused on the production of prototype castings, which is mapped out starting from the drawing documentation up to the production of the casting itself. The FDM method was applied for the production of the 3D pattern. Its main objective was to find out what dimensional changes happened during individual production stages, starting from the 3D pattern printing through a silicon mould production, wax patterns casting, making shells, melting out wax from shells and drying, up to the production of the final casting itself. Five measurements of determined dimensions were made during the production, which were processed and evaluated mathematically. A determination of shrinkage and a proposal of measures to maintain the dimensional stability of the final casting so as to meet requirements specified by a customer were the results.

  17. Applying RP-FDM Technology to Produce Prototype Castings Using the Investment Casting Method

    Directory of Open Access Journals (Sweden)

    M. Macků

    2012-09-01

    Full Text Available The research focused on the production of prototype castings, which is mapped out starting from the drawing documentation up to theproduction of the casting itself. The FDM method was applied for the production of the 3D pattern. Its main objective was to find out whatdimensional changes happened during individual production stages, starting from the 3D pattern printing through a silicon mouldproduction, wax patterns casting, making shells, melting out wax from shells and drying, up to the production of the final casting itself.Five measurements of determined dimensions were made during the production, which were processed and evaluated mathematically.A determination of shrinkage and a proposal of measures to maintain the dimensional stability of the final casting so as to meetrequirements specified by a customer were the results.

  18. Experimental methods of actuation, characterization and prototyping of hydrogels for bioMEMS/NEMS applications.

    Science.gov (United States)

    Khaleque, T; Abu-Salih, S; Saunders, J R; Moussa, W

    2011-03-01

    As a member of the smart polymer material group, stimuli responsive hydrogels have achieved a wide range of applications in microfluidic devices, micro/nano bio and environmental sensors, biomechanics and drug delivery systems. To optimize the utilization of a hydrogel in various micro and nano applications it is essential to have a better understanding of its mechanical and electrical properties. This paper presents a review of the different techniques used to determine a hydrogel's mechanical properties, including tensile strength, compressive strength and shear modulus and the electrical properties including electrical conductivity and dielectric permittivity. Also explored the effect of various prototyping factors and the mechanisms by which these factors are used to alter the mechanical and electrical properties of a hydrogel. Finally, this review discusses a wide range of hydrogel fabrication techniques and methods used, to date, to actuate this family of smart polymer material.

  19. A universal, rapid, and inexpensive method for genomic DNA ...

    Indian Academy of Sciences (India)

    MOHAMMED BAQUR SAHIB A. AL-SHUHAIB

    Abstract. There is no 'one' procedure for extracting DNA from the whole blood of both mammals and birds, since each species has a unique property that require different methods to release its own DNA. Therefore, to obtain genomic DNA, a universal, rapid, and noncostly method was developed. A very simple biological ...

  20. Rapid, cost-effective liquid chromatograghic method for the ...

    African Journals Online (AJOL)

    GRACE

    2006-07-03

    Jul 3, 2006 ... 1Department of Medicinal Chemistry and Quality Control, National Institute for Pharmaceutical Research and Development, Abuja,. Nigeria. ... A rapid and cost effective method for the analysis of metronidazole in biological samples was ... effective HPLC method of assaying metronidazole both in.

  1. A universal, rapid, and inexpensive method for genomic DNA ...

    Indian Academy of Sciences (India)

    ... of both mammals and birds, since each species has a unique property that require different methods to release its own DNA. Therefore, to obtain genomic DNA, a universal, rapid, and noncostly method was developed. A very simple biological basis is followed in this procedure, in which, when the bloodis placed in water, ...

  2. Bony defect repair in rabbit using hybrid rapid prototyping polylactic co glycolic acid/β tricalciumphosphate collagen I/apatite scaffold and bone marrow mesenchymal stem cells

    Directory of Open Access Journals (Sweden)

    Long Pang

    2013-01-01

    Full Text Available Background: In bone tissue engineering, extracellular matrix exerts critical influence on cellular interaction with porous biomaterial and the apatite playing an important role in the bonding process of biomaterial to bone tissue. The aim of this study was to observe the therapeutic effects of hybrid rapid prototyping (RP scaffolds comprising polylactic-co-glycolic acid (PLGA, β-tricalciumphosphate (β-TCP, collagen I and apatite (PLGA/β-TCP-collagen I/apatite on segmental bone defects in conjunction with combination with bone marrow mesenchymal stem cells (BMSCs. Materials and Methods: BMSCs were seeded into the hybrid RP scaffolds to repair 15 mm defect in the radius of rabbits. Radiograph, microcomputed tomography and histology were used to evaluate new bone formation. Results: Radiographic analysis done from 12 to 36 weeks postoperative period demonstrated that new bone formed at the radial defect site and continues to increase until the medullary cavity is recanalized and remodelling is complete. The bone defect remained unconnected in the original RP scaffolds (PLGA/β-TCP during the whole study. Histological observations conformed to the radiographic images. In hybrid RP scaffold group, woven bone united the radial defect at 12 weeks and consecutively remodeled into lamellar bone 24 weeks postoperation and finally matured into cortical bone with normal marrow cavity after another 12 weeks. No bone formation but connective tissue has been detected in RP scaffold at the same time. Conclusion: Collagen I/apatite sponge composite coating could improve new bone formation in vivo. The hybrid RP scaffold of PLGA/β-TCP skeleton with collagen I/apatite sponge composite coating is a promising candidate for bone tissue engineering.

  3. Bony defect repair in rabbit using hybrid rapid prototyping polylactic-co-glycolic acid/β-tricalciumphosphate collagen I/apatite scaffold and bone marrow mesenchymal stem cells

    Science.gov (United States)

    Pang, Long; Hao, Wei; Jiang, Ming; Huang, Jianguo; Yan, Yongnian; Hu, Yunyu

    2013-01-01

    Background: In bone tissue engineering, extracellular matrix exerts critical influence on cellular interaction with porous biomaterial and the apatite playing an important role in the bonding process of biomaterial to bone tissue. The aim of this study was to observe the therapeutic effects of hybrid rapid prototyping (RP) scaffolds comprising polylactic-co-glycolic acid (PLGA), β-tricalciumphosphate (β-TCP), collagen I and apatite (PLGA/β-TCP-collagen I/apatite) on segmental bone defects in conjunction with combination with bone marrow mesenchymal stem cells (BMSCs). Materials and Methods: BMSCs were seeded into the hybrid RP scaffolds to repair 15 mm defect in the radius of rabbits. Radiograph, microcomputed tomography and histology were used to evaluate new bone formation. Results: Radiographic analysis done from 12 to 36 weeks postoperative period demonstrated that new bone formed at the radial defect site and continues to increase until the medullary cavity is recanalized and remodelling is complete. The bone defect remained unconnected in the original RP scaffolds (PLGA/β-TCP) during the whole study. Histological observations conformed to the radiographic images. In hybrid RP scaffold group, woven bone united the radial defect at 12 weeks and consecutively remodeled into lamellar bone 24 weeks postoperation and finally matured into cortical bone with normal marrow cavity after another 12 weeks. No bone formation but connective tissue has been detected in RP scaffold at the same time. Conclusion: Collagen I/apatite sponge composite coating could improve new bone formation in vivo. The hybrid RP scaffold of PLGA/β-TCP skeleton with collagen I/apatite sponge composite coating is a promising candidate for bone tissue engineering. PMID:23960284

  4. Minimizing the extra-oral time in autogeneous tooth transplantation: use of computer-aided rapid prototyping (CARP as a duplicate model tooth

    Directory of Open Access Journals (Sweden)

    Seung-Jong Lee

    2012-08-01

    Full Text Available Objectives The maintenance of the healthy periodontal ligament cells of the root surface of donor tooth and intimate surface contact between the donor tooth and the recipient bone are the key factors for successful tooth transplantation. In order to achieve these purposes, a duplicated donor tooth model can be utilized to reduce the extra-oral time using the computer-aided rapid prototyping (CARP technique. Materials and Methods Briefly, a three-dimensional digital imaging and communication in medicine (DICOM image with the real dimensions of the donor tooth was obtained from a computed tomography (CT, and a life-sized resin tooth model was fabricated. Dimensional errors between real tooth, 3D CT image model and CARP model were calculated. And extra-oral time was recorded during the autotransplantation of the teeth. Results The average extra-oral time was 7 min 25 sec with the range of immediate to 25 min in cases which extra-oral root canal treatments were not performed while it was 9 min 15 sec when extra-oral root canal treatments were performed. The average radiographic distance between the root surface and the alveolar bone was 1.17 mm and 1.35 mm at mesial cervix and apex; they were 0.98 mm and 1.26 mm at the distal cervix and apex. When the dimensional errors between real tooth, 3D CT image model and CARP model were measured in cadavers, the average of absolute error was 0.291 mm between real teeth and CARP model. Conclusions These data indicate that CARP may be of value in minimizing the extra-oral time and the gap between the donor tooth and the recipient alveolar bone in tooth transplantation.

  5. Methods for Rapid Screening in Woody Plant Herbicide Development

    Directory of Open Access Journals (Sweden)

    William Stanley

    2014-07-01

    Full Text Available Methods for woody plant herbicide screening were assayed with the goal of reducing resources and time required to conduct preliminary screenings for new products. Rapid screening methods tested included greenhouse seedling screening, germinal screening, and seed screening. Triclopyr and eight experimental herbicides from Dow AgroSciences (DAS 313, 402, 534, 548, 602, 729, 779, and 896 were tested on black locust, loblolly pine, red maple, sweetgum, and water oak. Screening results detected differences in herbicide and species in all experiments in much less time (days to weeks than traditional field screenings and consumed significantly less resources (<500 mg acid equivalent per herbicide per screening. Using regression analysis, various rapid screening methods were linked into a system capable of rapidly and inexpensively assessing herbicide efficacy and spectrum of activity. Implementation of such a system could streamline early-stage herbicide development leading to field trials, potentially freeing resources for use in development of beneficial new herbicide products.

  6. A rapid ultrasound particle agglutination method for HIV antibody detection: Comparison with conventional rapid HIV tests.

    Science.gov (United States)

    Bystryak, Simon; Ossina, Natalya

    2017-11-01

    We present the results of the feasibility and preliminary studies on analytical performance of a rapid test for detection of human immunodeficiency virus (HIV) antibodies in human serum or plasma that is an important advance in detecting HIV infection. Current methods for rapid testing of antibodies against HIV are qualitative and exhibit poor sensitivity (limit of detection). In this paper, we describe an ultrasound particle agglutination (UPA) method that leads to a significant increase of the sensitivity of conventional latex agglutination tests for HIV antibody detection in human serum or plasma. The UPA method is based on the use of: 1) a dual mode ultrasound, wherein a first single-frequency mode is used to accelerate the latex agglutination process, and then a second swept-frequency mode of sonication is used to disintegrate non-specifically bound aggregates; and 2) a numerical assessment of results of the agglutination process. The numerical assessment is carried out by optical detection and analysis of moving patterns in the resonator cell during the swept-frequency mode. The single-step UPA method is rapid and more sensitive than the three commercial rapid HIV test kits analyzed in the study: analytical sensitivity of the new UPA method was found to be 510-, 115-, and 80-fold higher than that for Capillus™, Multispot™ and Uni-Gold™ Recombigen HIV antibody rapid test kits, respectively. The newly developed UPA method opens up additional possibilities for detection of a number of clinically significant markers in point-of-care settings. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Rapid virtual prototyping of complex photonic integrated circuits using layout-aware schematic-driven design methodology

    Science.gov (United States)

    Mingaleev, S.; Richter, A.; Sokolov, E.; Savitzki, S.; Polatynski, A.; Farina, J.; Koltchanov, I.

    2017-02-01

    We present our versatile simulation framework for the schematic-driven and layout-aware design of photonic integrated circuits (PICs) realizing a fast and user-friendly design flow for large-scale PICs comprising passive and active building blocks (BBs). We show how the seamless interaction of circuit simulation with photonic layout design tools allows to specify and utilize directly physical locations and orientations of BBs of standardized process design kits (PDKs). We demonstrate how to combine graphical schematic capture and automated waveguide routing, and discuss by means of typical design applications how an optimized design flow can speed-up the virtual prototyping of complex PICs and optoelectronic applications.

  8. Usefulness of computed tomography in pre-surgical evaluation of maxillo-facial pathology with rapid prototyping and surgical pre-planning by virtual reality.

    Science.gov (United States)

    Toso, Francesco; Zuiani, Chiara; Vergendo, Maurizio; Salvo, Iolanda; Robiony, Massimo; Politi, Massimo; Bazzocchi, Massimo

    2005-01-01

    To validate a protocol for creating virtual models to be used in the construction of solid prototypes useful for the planning-simulation of maxillo-facial surgery, in particular for very complex anatomic and pathologic problems. To optimize communications between the radiology, engineering and surgical laboratories. We studied 16 patients with different clinical problems of the maxillo-facial district. Exams were performed with multidetector computed tomography (MDCT) and single slice computed tomography (SDCT) with axial scans and collimation of 0.5-2 mm, and reconstruction interval of 1 mm. Subsequently we performed 2D multiplanar reconstructions and 3D volume-rendering reconstructions. We exported the DICOM images to the engineering laboratory, to recognize and isolate the bony structures by software. With these data the solid prototypes were generated using stereolitography. To date, surgery has been preformed on 12 patients after simulation of the procedure on the stereolithographyc model. The solid prototypes constructed in the difficult cases were sufficiently detailed despite problems related to the artefacts generated by dental fillings an d prostheses. In the remaining cases the MPR/3D images were sufficiently detailed for surgical planning. The surgical results were excellent in all patients who underwent surgery, and the surgeons were satisfied with the improvement in quality and the reduction in time required for the procedure. MDCT enables rapid prototyping using solid replication, which was very helpful in maxillo-facial surgery, despite problems related to artifacts due to dental fillings and prosthesis within the acquisition field; solutions for this problem are work in progress. The protocol used for communication between the different laboratories was valid and reproducible.

  9. Correction of a severe facial asymmetry with computerized planning and with the use of a rapid prototyped surgical template: a case report/technique article.

    Science.gov (United States)

    Seres, Laszlo; Varga, Endre; Kocsis, Andras; Rasko, Zoltan; Bago, Balazs; Varga, Endre; Piffko, Jozsef

    2014-07-11

    Management of significant facial asymmetry presents a challenge due to the geometric complexity of the bony and other facial structures. Manual model surgery is an essential part of treatment planning but it can be complicated, time-consuming and may contain potential errors. Computer-aided surgery has revolutionized the correction of maxillofacial deformities. The aim of this study was to report a case of facial asymmetry when computerised simulation surgery was performed instead of manual model surgery and a virtually planned wafer splint was fabricated. A 26-year-old male was presented with a severe right-sided hemimandibular elongation. Following presurgical orthodontics high-resolution computer tomography scan was performed. The stack images were reformatted into a three-dimensional structure. Virtual Le Fort-I osteotomy was performed and the symmetry of the maxilla was corrected with the help of a three-dimensional planning software. A virtual intermediate surgical wafer was designed and produced with three-dimensional rapid prototyping technology. The mandible was rotated into the correct position following virtual bilateral sagittal split osteotomy to visualize the movements of the osteotomised mandibular segments. The two-jaw procedure was performed according to the virtual plan. The facial symmetry was improved significantly and stable occlusion was achieved. This complex case shows the advantages of computer-aided surgical planning and three-dimensional rapid prototyping for the correction of facial asymmetries.

  10. Feasibility study on production of Metal Matrix Composite (MMC material for Electrical Discharge Machining (EDM tools using Rapid Prototyping (RP technique

    Directory of Open Access Journals (Sweden)

    Shamsudin S.

    2017-01-01

    Full Text Available In common practice, tools for EDM have traditionally been made by machining copper or graphite to the required profile using CNC machines. Increasing the degree of complexity of any tooling design for any operations results in a corresponding increase in time and cost required. With the advent of rapid prototyping techniques, the problem of making tools with complex shapes becomes much simpler and easy. The main aim of this research was to develop new EDM electrode material through a novel approach by rapid prototyping (RP technique. In this study, the potential application of copper (Cu reinforced alumina (Al2O3 fabricated with various compositions as an EDM electrode was investigated. The electrodes were fabricated by Canon PIXMA IP 1800 printer and underwent sintering temperature at 85 % and 95 % melting point of copper. The EDMed workpiece was aluminium and the electrodes surface was analyzed through scanning electron microscope (SEM. Findings showed that the electrode with Cu - 0 vol. %Al2O3 composite and sintered at temperature 977 °C resulted in highest metal removal rate (MRR and lowest electrode wear rate (EWR while Cu – 10 vol. %Al2O3 composite and sintered at temperature 977 °C revealed a better surface finish than other electrodes. An increase in Al2O3 content in general will increase the hardness of tool, as a trade-off, the conductivity was reduced.

  11. Immediate mandibular reconstruction via patient-specific titanium mesh tray using electron beam melting/CAD/rapid prototyping techniques: One-year follow-up.

    Science.gov (United States)

    Farid Shehab, Mohamed; Hamid, Nabila Mohammed Abdel; Askar, Nevien Abdullatif; Elmardenly, Ahmed Mokhtar

    2018-02-21

    Immediate mandibular reconstruction was performed using a patient-specific titanium mesh tray fabricated by electron beam melting (EBM) /rapid prototyping techniques. Patient-specific titanium trays were virtually designed and fabricated using EBM technology/rapid prototyping for patients requiring mandibular resection and immediate reconstruction using an iliac crest bone graft. Dental implants were placed in the grafted sites and the patients received prosthetic rehabilitation with a follow-up of one year. Clinical data, postoperative bone formation and complications were evaluated. A symmetric appearance of facial contours was achieved. The titanium tray incorporated the particulate iliac crest bone graft that provided significant bone formation (mean 18.97 ± 1.45 mm) and predictable results. Stability of the dental implants was achieved. The patient-specific titanium meshes and immediate particulate autogenous bone graft showed satisfactory clinical and surgical results in improving patients' quality of life and decreasing the overall treatment time with adequate functional rehabilitation. Copyright © 2018 John Wiley & Sons, Ltd.

  12. RAPID SEPARATION METHOD FOR ACTINIDES IN EMERGENCY SOIL SAMPLES

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, S.; Culligan, B.; Noyes, G.

    2009-11-09

    A new rapid method for the determination of actinides in soil and sediment samples has been developed at the Savannah River Site Environmental Lab (Aiken, SC, USA) that can be used for samples up to 2 grams in emergency response situations. The actinides in soil method utilizes a rapid sodium hydroxide fusion method, a lanthanum fluoride soil matrix removal step, and a streamlined column separation process with stacked TEVA, TRU and DGA Resin cartridges. Lanthanum was separated rapidly and effectively from Am and Cm on DGA Resin. Vacuum box technology and rapid flow rates are used to reduce analytical time. Alpha sources are prepared using cerium fluoride microprecipitation for counting by alpha spectrometry. The method showed high chemical recoveries and effective removal of interferences. This new procedure was applied to emergency soil samples received in the NRIP Emergency Response exercise administered by the National Institute for Standards and Technology (NIST) in April, 2009. The actinides in soil results were reported within 4-5 hours with excellent quality.

  13. Rapid method to estimate temperature changes in electronics elements

    Directory of Open Access Journals (Sweden)

    Oborskii G. A., Savel’eva O. S., Shikhireva Yu. V.

    2014-06-01

    Full Text Available Thermal behavior of electronic equipment is the determining factor for performing rapid assessment of the effectiveness of design and operation of the equipment. The assessment method proposed in this article consists in fixation of an infrared video stream from the surface of the device and converting it into a visible flow by means of a thermal imager, splitting it into component colors and their further processing using parabolic transformation. The result of the transformation is the number used as a rapid criterion for estimation of distribution stability of heat in the equipment.

  14. Rapid methods for detection of bacterial resistance to antibiotics.

    Science.gov (United States)

    March-Rosselló, Gabriel Alberto

    2017-03-01

    The most widely used antibiotic susceptibility testing methods in Clinical Microbiology are based on the phenotypic detection of antibiotic resistance by measuring bacterial growth in the presence of the antibiotic being tested. These conventional methods take typically 24hours to obtain results. Here we review the main techniques for rapid determination of antibiotic susceptibility. Data obtained with different methods such as molecular techniques, microarrays, commercial methods used in work routine, immunochromatographic methods, colorimetric methods, image methods, nephelometry, MALDI-TOF mass spectrometry, flow cytometry, chemiluminescence and bioluminescence, microfluids and methods based on cell disruption are analysed in detail. Copyright © 2016 Elsevier España, S.L.U. and Sociedad Española de Enfermedades Infecciosas y Microbiología Clínica. All rights reserved.

  15. A similarity-based community detection method with multiple prototype representation

    OpenAIRE

    Zhou, Kuang; Martin, Arnaud; Pan, Quan

    2015-01-01

    International audience; Communities are of great importance for understanding graph structures in social networks. Some existing community detection algorithms use a single prototype to represent each group. In real applications, this may not adequately model the different types of communities and hence limits the clustering performance on social networks. To address this problem, a Similarity-based Multi-Prototype (SMP) community detection approach is proposed in this paper. In SMP, vertices...

  16. Rapid and Accurate Assembly Method for a New Laue Lens Prototype

    DEFF Research Database (Denmark)

    Wade, Colin; Barriere, Nicolas; Hanlon, Lorraine

    2015-01-01

    The Laue lens is a technology for gamma-ray astrophysics whereby gamma-rays of particular energies can be focused by a suitable arrangement of crystals. The Laue lens assembly station at UC Berkeley was used to build a technological demonstrator addressing the key issues of crystal mounting speed...

  17. Surface quality of foundry pattern manufactured by FDM method - rapid prototyping

    Directory of Open Access Journals (Sweden)

    A. Hanus

    2011-01-01

    Full Text Available The goal of this paper was to verify the possibilities of using 3D models produced by means of the FDM technology for actual foundryproduction. Experimental models were produced using Dimension sst 768 3D printer. Two types of castings (type I - simple plates, type II- jewellery were cast in plaster moulds. The models were burnt out at 500 °C. The goal of the experiment was to verify the effect ofmodifications upon surface quality of the resulting casting. The ABS model was tested with unmodified surface, chemically treatedsurface, blasted surface and blasted and etched surface together. The results of the experiment have confirmed the assumed effect of bothmechanical and chemical modifications of the model surface on casting surface quality.

  18. Comparison of Two Inexpensive Rapid Prototyping Methods for Manufacturing Filament Target Ultrasound Phantoms.

    Science.gov (United States)

    Füzesi, Krisztián; Gyöngy, Miklós

    2017-03-01

    Current use of 3-D printers to manufacture ultrasound phantoms is limited to relatively expensive photopolymer jetting printers. The present work investigates the feasibility of using two common and inexpensive 3-D printer technologies, fused deposition modeling (FDM) and digital light processing (DLP), to print custom filament target phantoms. Acoustic characteristics obtained from printed solid blocks indicated that the printing materials-acrylonitrile butadiene styrene and polylactic acid for FDM and a photopolymer for DLP printing-were appropriate for use as scatterers. A regular grid of filaments was printed to study printing accuracy. As a proof of concept of the phantom manufacturing process, a complex pattern of filament targets was placed in de-ionized water to create a phantom, which was then imaged using an ultrasound imager. The pattern was clearly identifiable, although multiple reflections were observed, which underscores the importance of future work to enhance printing resolution. This goal is deemed possible using improvement of the DLP printing setup. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

  19. Setting Cut Scores on an EFL Placement Test Using the Prototype Group Method: A Receiver Operating Characteristic (ROC) Analysis

    Science.gov (United States)

    Eckes, Thomas

    2017-01-01

    This paper presents an approach to standard setting that combines the prototype group method (PGM; Eckes, 2012) with a receiver operating characteristic (ROC) analysis. The combined PGM-ROC approach is applied to setting cut scores on a placement test of English as a foreign language (EFL). To implement the PGM, experts first named learners whom…

  20. A methodical way of prototyping integrated and ecological arable farming systems (I/EAFS) in interaction with pilot farms

    NARCIS (Netherlands)

    Vereijken, P.H.

    1997-01-01

    A methodical way of prototyping integrated and ecological arable farming systems (I/EAFS) in interaction with pilot farms is presented. It concerns a comprehensive and consistent approach of 5 steps. Step 1 is establishing a hierarchy of objectives considering the shortcomings of current farming

  1. Evaluation of a Rapid Method of Determination of Plasma Fibrinogen

    Science.gov (United States)

    Thomson, G. W.; McSherry, B. J.; Valli, V. E. O.

    1974-01-01

    An evaluation was made of a rapid semiautomated method of determining fibrinogen levels in bovine plasma. This method, the fibrometer method of Morse, Panek and Menga (8), is based on the principle that when thrombin is added to suitably diluted plasma the time of clotting is linearly related to the fibrinogen concentration. A standard curve prepared using bovine plasma had an r value of .9987 and analysis of variance showed there was no significant deviation from regression. A comparison of the fibrometer method and the biuret method of Ware, Guest and Seegers done on 158 bovine plasma samples showed good correlation between the two methods. It was concluded that the fibrometer method does measure bovine fibrinogen and has considerable merit for use in clinical diseases of cattle. PMID:4277474

  2. Rapid methods for determination of fluoxetine in pharmaceutical formulations.

    Science.gov (United States)

    Mandrioli, R; Pucci, V; Visini, D; Varani, G; Raggi, M A

    2002-08-01

    Two different analytical methods for the quality control of fluoxetine in commercial formulations have been developed and compared: a spectrofluorimetric method and a capillary zone electrophoretic (CZE) method. The fluorescence emission values were measured at lambda=293 nm when exciting at lambda=230 nm. The CZE method used an uncoated fused-silica capillary and pH 2.5 phosphate buffer as the background electrolyte. The extraction of fluoxetine from the capsules consisted of a simple one-step dissolution with methanol/water, filtration and dilution. Both methods gave satisfactory results in terms of precision; the best results were obtained for the electrophoretic method, with RSD% values always lower than 2.0%. The accuracy was assessed by means of recovery studies, which gave very good results, between 97.5 and 102.6%. Furthermore, both methods also have the advantage of being very rapid.

  3. A simple and rapid method for determining transgenic cotton plants.

    Science.gov (United States)

    Zhang, Baohong; Wang, Hongmei; Liu, Fang; Wang, Qinglian

    2013-01-01

    Determining transgenic events is a critical step for obtaining transgenic plants as well as the later stage of application. Traditional methods, such as Northern blotting and qRT-PCR, for determining transgenic events either require radioactively labeled substrates, expensive instruments, or long-time commitments, which result in lab and time-consuming as well as expensive costs. These methods also require destroying the transgenic events. In this chapter, we present a simple and rapid method for determining transgenic cotton plants in both laboratory and field conditions. This method is based on the sensitivity of transgenic and non-transgenic plants to a specific chemical, such as antibiotics or herbicides. This method will facilitate the screening of transgenic events, save time, reduce cost, and speed up the application of transgenic technology on cotton breeding and production. More important, this is a nondestructive bioassay method; the transgenic plants can be transferred into greenhouse or field for the later study after the detection process.

  4. Rapid and selective method for quantitation of metronidazole in pharmaceuticals.

    Science.gov (United States)

    Sanyal, A K

    1988-01-01

    A selective and highly sensitive assay for N-1-substituted nitroimidazoles has been modified and adapted for rapid estimation of metronidazole in pharmaceuticals. The color reaction is based on diazotization of sulfanilamide with the nitrite ions liberated by alkaline hydrolysis of metronidazole and subsequent coupling of the diazonium salt with N-1-(naphthyl)-ethylenediamine dihydrochloride. This method is applicable for the assay of benzoyl metronidazole in oral suspension. Officially recommended excipients and preservatives do not interfere.

  5. Preparing Silica Aerogel Monoliths via a Rapid Supercritical Extraction Method

    Science.gov (United States)

    Gorka, Caroline A.

    2014-01-01

    A procedure for the fabrication of monolithic silica aerogels in eight hours or less via a rapid supercritical extraction process is described. The procedure requires 15-20 min of preparation time, during which a liquid precursor mixture is prepared and poured into wells of a metal mold that is placed between the platens of a hydraulic hot press, followed by several hours of processing within the hot press. The precursor solution consists of a 1.0:12.0:3.6:3.5 x 10-3 molar ratio of tetramethylorthosilicate (TMOS):methanol:water:ammonia. In each well of the mold, a porous silica sol-gel matrix forms. As the temperature of the mold and its contents is increased, the pressure within the mold rises. After the temperature/pressure conditions surpass the supercritical point for the solvent within the pores of the matrix (in this case, a methanol/water mixture), the supercritical fluid is released, and monolithic aerogel remains within the wells of the mold. With the mold used in this procedure, cylindrical monoliths of 2.2 cm diameter and 1.9 cm height are produced. Aerogels formed by this rapid method have comparable properties (low bulk and skeletal density, high surface area, mesoporous morphology) to those prepared by other methods that involve either additional reaction steps or solvent extractions (lengthier processes that generate more chemical waste).The rapid supercritical extraction method can also be applied to the fabrication of aerogels based on other precursor recipes. PMID:24637334

  6. Rapid Enzymatic Method for Pectin Methyl Esters Determination

    Directory of Open Access Journals (Sweden)

    Lucyna Łękawska-Andrinopoulou

    2013-01-01

    Full Text Available Pectin is a natural polysaccharide used in food and pharma industries. Pectin degree of methylation is an important parameter having significant influence on pectin applications. A rapid, fully automated, kinetic flow method for determination of pectin methyl esters has been developed. The method is based on a lab-made analyzer using the reverse flow-injection/stopped flow principle. Methanol is released from pectin by pectin methylesterase in the first mixing coil. Enzyme working solution is injected further downstream and it is mixed with pectin/pectin methylesterase stream in the second mixing coil. Methanol is oxidized by alcohol oxidase releasing formaldehyde and hydrogen peroxide. This reaction is coupled to horse radish peroxidase catalyzed reaction, which gives the colored product 4-N-(p-benzoquinoneimine-antipyrine. Reaction rate is proportional to methanol concentration and it is followed using Ocean Optics USB 2000+ spectrophotometer. The analyzer is fully regulated by a lab written LabVIEW program. The detection limit was 1.47 mM with an analysis rate of 7 samples h−1. A paired t-test with results from manual method showed that the automated method results are equivalent to the manual method at the 95% confidence interval. The developed method is rapid and sustainable and it is the first application of flow analysis in pectin analysis.

  7. 3D Rapid Prototyping for Otolaryngology—Head and Neck Surgery: Applications in Image-Guidance, Surgical Simulation and Patient-Specific Modeling

    Science.gov (United States)

    Chan, Harley H. L.; Siewerdsen, Jeffrey H.; Vescan, Allan; Daly, Michael J.; Prisman, Eitan; Irish, Jonathan C.

    2015-01-01

    The aim of this study was to demonstrate the role of advanced fabrication technology across a broad spectrum of head and neck surgical procedures, including applications in endoscopic sinus surgery, skull base surgery, and maxillofacial reconstruction. The initial case studies demonstrated three applications of rapid prototyping technology are in head and neck surgery: i) a mono-material paranasal sinus phantom for endoscopy training ii) a multi-material skull base simulator and iii) 3D patient-specific mandible templates. Digital processing of these phantoms is based on real patient or cadaveric 3D images such as CT or MRI data. Three endoscopic sinus surgeons examined the realism of the endoscopist training phantom. One experienced endoscopic skull base surgeon conducted advanced sinus procedures on the high-fidelity multi-material skull base simulator. Ten patients participated in a prospective clinical study examining patient-specific modeling for mandibular reconstructive surgery. Qualitative feedback to assess the realism of the endoscopy training phantom and high-fidelity multi-material phantom was acquired. Conformance comparisons using assessments from the blinded reconstructive surgeons measured the geometric performance between intra-operative and pre-operative reconstruction mandible plates. Both the endoscopy training phantom and the high-fidelity multi-material phantom received positive feedback on the realistic structure of the phantom models. Results suggested further improvement on the soft tissue structure of the phantom models is necessary. In the patient-specific mandible template study, the pre-operative plates were judged by two blinded surgeons as providing optimal conformance in 7 out of 10 cases. No statistical differences were found in plate fabrication time and conformance, with pre-operative plating providing the advantage of reducing time spent in the operation room. The applicability of common model design and fabrication techniques

  8. 3D Rapid Prototyping for Otolaryngology-Head and Neck Surgery: Applications in Image-Guidance, Surgical Simulation and Patient-Specific Modeling.

    Directory of Open Access Journals (Sweden)

    Harley H L Chan

    Full Text Available The aim of this study was to demonstrate the role of advanced fabrication technology across a broad spectrum of head and neck surgical procedures, including applications in endoscopic sinus surgery, skull base surgery, and maxillofacial reconstruction. The initial case studies demonstrated three applications of rapid prototyping technology are in head and neck surgery: i a mono-material paranasal sinus phantom for endoscopy training ii a multi-material skull base simulator and iii 3D patient-specific mandible templates. Digital processing of these phantoms is based on real patient or cadaveric 3D images such as CT or MRI data. Three endoscopic sinus surgeons examined the realism of the endoscopist training phantom. One experienced endoscopic skull base surgeon conducted advanced sinus procedures on the high-fidelity multi-material skull base simulator. Ten patients participated in a prospective clinical study examining patient-specific modeling for mandibular reconstructive surgery. Qualitative feedback to assess the realism of the endoscopy training phantom and high-fidelity multi-material phantom was acquired. Conformance comparisons using assessments from the blinded reconstructive surgeons measured the geometric performance between intra-operative and pre-operative reconstruction mandible plates. Both the endoscopy training phantom and the high-fidelity multi-material phantom received positive feedback on the realistic structure of the phantom models. Results suggested further improvement on the soft tissue structure of the phantom models is necessary. In the patient-specific mandible template study, the pre-operative plates were judged by two blinded surgeons as providing optimal conformance in 7 out of 10 cases. No statistical differences were found in plate fabrication time and conformance, with pre-operative plating providing the advantage of reducing time spent in the operation room. The applicability of common model design and

  9. 3D Rapid Prototyping for Otolaryngology-Head and Neck Surgery: Applications in Image-Guidance, Surgical Simulation and Patient-Specific Modeling.

    Science.gov (United States)

    Chan, Harley H L; Siewerdsen, Jeffrey H; Vescan, Allan; Daly, Michael J; Prisman, Eitan; Irish, Jonathan C

    2015-01-01

    The aim of this study was to demonstrate the role of advanced fabrication technology across a broad spectrum of head and neck surgical procedures, including applications in endoscopic sinus surgery, skull base surgery, and maxillofacial reconstruction. The initial case studies demonstrated three applications of rapid prototyping technology are in head and neck surgery: i) a mono-material paranasal sinus phantom for endoscopy training ii) a multi-material skull base simulator and iii) 3D patient-specific mandible templates. Digital processing of these phantoms is based on real patient or cadaveric 3D images such as CT or MRI data. Three endoscopic sinus surgeons examined the realism of the endoscopist training phantom. One experienced endoscopic skull base surgeon conducted advanced sinus procedures on the high-fidelity multi-material skull base simulator. Ten patients participated in a prospective clinical study examining patient-specific modeling for mandibular reconstructive surgery. Qualitative feedback to assess the realism of the endoscopy training phantom and high-fidelity multi-material phantom was acquired. Conformance comparisons using assessments from the blinded reconstructive surgeons measured the geometric performance between intra-operative and pre-operative reconstruction mandible plates. Both the endoscopy training phantom and the high-fidelity multi-material phantom received positive feedback on the realistic structure of the phantom models. Results suggested further improvement on the soft tissue structure of the phantom models is necessary. In the patient-specific mandible template study, the pre-operative plates were judged by two blinded surgeons as providing optimal conformance in 7 out of 10 cases. No statistical differences were found in plate fabrication time and conformance, with pre-operative plating providing the advantage of reducing time spent in the operation room. The applicability of common model design and fabrication techniques

  10. SIMS: a hybrid method for rapid conformational analysis.

    Directory of Open Access Journals (Sweden)

    Bryant Gipson

    Full Text Available Proteins are at the root of many biological functions, often performing complex tasks as the result of large changes in their structure. Describing the exact details of these conformational changes, however, remains a central challenge for computational biology due the enormous computational requirements of the problem. This has engendered the development of a rich variety of useful methods designed to answer specific questions at different levels of spatial, temporal, and energetic resolution. These methods fall largely into two classes: physically accurate, but computationally demanding methods and fast, approximate methods. We introduce here a new hybrid modeling tool, the Structured Intuitive Move Selector (sims, designed to bridge the divide between these two classes, while allowing the benefits of both to be seamlessly integrated into a single framework. This is achieved by applying a modern motion planning algorithm, borrowed from the field of robotics, in tandem with a well-established protein modeling library. sims can combine precise energy calculations with approximate or specialized conformational sampling routines to produce rapid, yet accurate, analysis of the large-scale conformational variability of protein systems. Several key advancements are shown, including the abstract use of generically defined moves (conformational sampling methods and an expansive probabilistic conformational exploration. We present three example problems that sims is applied to and demonstrate a rapid solution for each. These include the automatic determination of "active" residues for the hinge-based system Cyanovirin-N, exploring conformational changes involving long-range coordinated motion between non-sequential residues in Ribose-Binding Protein, and the rapid discovery of a transient conformational state of Maltose-Binding Protein, previously only determined by Molecular Dynamics. For all cases we provide energetic validations using well

  11. Two-dimensional finite element method simulation of a four-quadrant transducer prototype machine considering skewed slots

    Science.gov (United States)

    Zheng, Ping; Thelin, Peter; Nordlund, Erik; Sadarangani, Chandur

    2006-04-01

    A four-quadrant transducer (4QT) electric machine is an integrated electric machine used for hybrid electric vehicles. In this article a 4QT prototype machine that is radially integrated by two permanent-magnet synchronous machines is analyzed. Skewed slots are adopted for the two machines, and the multislice two-dimensional time-stepping finite element method is used to calculate the performance. The dividing method of the 4QT, the choice of calculated cutplanes and the determination of the number of slices are discussed. The no-load and load performance of the 4QT are calculated. The 4QT prototype machine was tested. The tested no-load line-to-line back electromotive force curves are in good agreement with the calculated ones, which verifies the feasibility of the proposed method.

  12. Rapid assessment methods in eye care: An overview

    Directory of Open Access Journals (Sweden)

    Srinivas Marmamula

    2012-01-01

    Full Text Available Reliable information is required for the planning and management of eye care services. While classical research methods provide reliable estimates, they are prohibitively expensive and resource intensive. Rapid assessment (RA methods are indispensable tools in situations where data are needed quickly and where time- or cost-related factors prohibit the use of classical epidemiological surveys. These methods have been developed and field tested, and can be applied across almost the entire gamut of health care. The 1990s witnessed the emergence of RA methods in eye care for cataract, onchocerciasis, and trachoma and, more recently, the main causes of avoidable blindness and visual impairment. The important features of RA methods include the use of local resources, simplified sampling methodology, and a simple examination protocol/data collection method that can be performed by locally available personnel. The analysis is quick and easy to interpret. The entire process is inexpensive, so the survey may be repeated once every 5-10 years to assess the changing trends in disease burden. RA survey methods are typically linked with an intervention. This article provides an overview of the RA methods commonly used in eye care, and emphasizes the selection of appropriate methods based on the local need and context.

  13. A rapid DNA extraction method suitable for human papillomavirus detection.

    Science.gov (United States)

    Brestovac, Brian; Wong, Michelle E; Costantino, Paul S; Groth, David

    2014-04-01

    Infection with oncogenic human papillomavirus (HPV) genotypes is necessary for the development of cervical cancer. Testing for HPV DNA from liquid based cervical samples can be used as an adjunct to traditional cytological screening. In addition there are ongoing viral load, genotyping, and prevalence studies. Therefore, a sensitive DNA extraction method is needed to maximize the efficiency of HPV DNA detection. The XytXtract Tissue kit is a DNA extraction kit that is rapid and so could be useful for HPV testing, particularly in screening protocols. This study was undertaken to determine the suitability of this method for HPV detection. DNA extraction from HeLa and Caski cell lines containing HPV 18 and 16 respectively together with DNA from five liquid based cervical samples were used in a HPV PCR assay. DNA was also extracted using the QIAamp DNA mini kit (Qiagen, Hilden, Germany) as a comparison. DNA extracts were serially diluted and assayed. HPV DNA was successfully detected in cell lines and cervical samples using the XytXtract Tissue kit. In addition, the XytXtract method was found to be more sensitive than the QIAmp method as determined by a dilution series of the extracted DNA. While the XytXtract method is a closed, the QIAamp method uses a spin column with possible loss of DNA through DNA binding competition of the matrix, which could impact on the final extraction efficiency. The XytXtract is a cheap, rapid and efficient method for extracting HPV DNA from both cell lines and liquid based cervical samples. © 2014 Wiley Periodicals, Inc.

  14. Rapid prototyping of anatomically shaped, tissue-engineered implants for restoring congruent articulating surfaces in small joints

    NARCIS (Netherlands)

    Woodfield, T.B.F.; Guggenheim, M.; von Rechenberg, B.; Riesle, J.U.; van Blitterswijk, Clemens; Wedler, V.

    2009-01-01

    Background: Preliminary studies investigated advanced scaffold design and tissue engineering approaches towards restoring congruent articulating surfaces in small joints. - Materials and methods: Anatomical femoral and tibial cartilage constructs, fabricated by three-dimensional fibre deposition

  15. Radiometric method for the rapid detection of Leptospira organisms

    Energy Technology Data Exchange (ETDEWEB)

    Manca, N.; Verardi, R.; Colombrita, D.; Ravizzola, G.; Savoldi, E.; Turano, A.

    1986-02-01

    A rapid and sensitive radiometric method for detection of Leptospira interrogans serovar pomona and Leptospira interrogans serovar copenhageni is described. Stuart's medium and Middlebrook TB (12A) medium supplemented with bovine serum albumin, catalase, and casein hydrolysate and labeled with /sup 14/C-fatty acids were used. The radioactivity was measured in a BACTEC 460. With this system, Leptospira organisms were detected in human blood in 2 to 5 days, a notably shorter time period than that required for the majority of detection techniques.

  16. Method for rapidly determining a pulp kappa number using spectrophotometry

    Science.gov (United States)

    Chai, Xin-Sheng; Zhu, Jun Yong

    2002-01-01

    A system and method for rapidly determining the pulp kappa number through direct measurement of the potassium permanganate concentration in a pulp-permanganate solution using spectrophotometry. Specifically, the present invention uses strong acidification to carry out the pulp-permanganate oxidation reaction in the pulp-permanganate solution to prevent the precipitation of manganese dioxide (MnO.sub.2). Consequently, spectral interference from the precipitated MnO.sub.2 is eliminated and the oxidation reaction becomes dominant. The spectral intensity of the oxidation reaction is then analyzed to determine the pulp kappa number.

  17. Rapid coulometric method for the Kjeldahl determination of nitrogen.

    Science.gov (United States)

    Boström, C A; Cedergren, A; Johansson, G; Pettersson, I

    1974-11-01

    A rapid coulometric method for the Kjeldahl determination of nitrogen is described. The samples are digested by means of the Tecator AB digestion system which permits forty samples to be digested at the same time. The digestion products are diluted to 75 ml and 1 ml is coulometrically titrated in 1-2 min: 20-30 determinations can be performed per hour. For substances containing nitrogen in the per cent range the relative standard deviations for eight different substances were 0.1-1%.

  18. A Novel Rapid Method to Determine Cannabis Seed Germination Ability

    OpenAIRE

    吉澤, 政夫; 荒金, 眞佐子; 鈴木, 幸子; 北川, 重美; 中嶋, 順一; 森, 謙一郎; 荻野, 周三; Masao, Yoshizawa; Masako, Aragane; Yukiko, Suzuki; Shigemi, Kitagawa; Jun'ichi, Nakajima; Ken'ichiro, Mori; Shuzo, Ogino; 東京都健康安全研究センター薬用植物園

    2011-01-01

    A novel rapid method to determine cannabis seed germination ability was developed. Cannabis seeds were soaked in water for 15 minutes at 40℃, and germs were removed from the seeds by cracking the shell with tweezers. The germs were soaked in water for 15 minutes at 40℃, and the swollen skin was peeled off. The peeled germs were again soaked in water for 10 minutes at 40℃, and the angles between the seed leaves were measured. Cannabis seeds with angles of the seed leaves exceeding 30 degrees w...

  19. Rapid prototyping of SoC-based real-time vision system: application to image preprocessing and face detection

    Science.gov (United States)

    Jridi, Maher; Alfalou, Ayman

    2017-05-01

    By this paper, the major goal is to investigate the Multi-CPU/FPGA SoC (System on Chip) design flow and to transfer a know-how and skills to rapidly design embedded real-time vision system. Our aim is to show how the use of these devices can be benefit for system level integration since they make possible simultaneous hardware and software development. We take the facial detection and pretreatments as case study since they have a great potential to be used in several applications such as video surveillance, building access control and criminal identification. The designed system use the Xilinx Zedboard platform. The last is the central element of the developed vision system. The video acquisition is performed using either standard webcam connected to the Zedboard via USB interface or several camera IP devices. The visualization of video content and intermediate results are possible with HDMI interface connected to HD display. The treatments embedded in the system are as follow: (i) pre-processing such as edge detection implemented in the ARM and in the reconfigurable logic, (ii) software implementation of motion detection and face detection using either ViolaJones or LBP (Local Binary Pattern), and (iii) application layer to select processing application and to display results in a web page. One uniquely interesting feature of the proposed system is that two functions have been developed to transmit data from and to the VDMA port. With the proposed optimization, the hardware implementation of the Sobel filter takes 27 ms and 76 ms for 640x480, and 720p resolutions, respectively. Hence, with the FPGA implementation, an acceleration of 5 times is obtained which allow the processing of 37 fps and 13 fps for 640x480, and 720p resolutions, respectively.

  20. Collaborative Prototyping

    DEFF Research Database (Denmark)

    Bogers, Marcel; Horst, Willem

    2014-01-01

    This paper presents an inductive study that shows how collaborative prototyping across functional, hierarchical, and organizational boundaries can improve the overall prototyping process. Our combined action research and case study approach provides new insights into how collaborative prototyping...... can provide a platform for prototype-driven problem solving in early new product development (NPD). Our findings have important implications for how to facilitate multistakeholder collaboration in prototyping and problem solving, and more generally for how to organize collaborative and open innovation...... processes. Our analysis reveals two levels of prototyping. Besides the more formal managerial level, we identify the informal designer level, where the actual practice of prototyping takes place. On this level, collaborative prototyping transforms the act of prototyping from an activity belonging...

  1. Prototype Positive Control Wells for Malaria Rapid Diagnostic Tests: Prospective Evaluation of Implementation Among Health Workers in Lao People's Democratic Republic and Uganda.

    Science.gov (United States)

    Bell, David; Bwanika, John Baptist; Cunningham, Jane; Gatton, Michelle; González, Iveth J; Hopkins, Heidi; Kibira, Simon Peter S; Kyabayinze, Daniel J; Mayxay, Mayfong; Ndawula, Bbaale; Newton, Paul N; Phommasone, Koukeo; Streat, Elizabeth; Umlauf, René

    2017-02-08

    Rapid diagnostic tests (RDTs) are widely used for malaria diagnosis, but lack of quality control at point of care restricts trust in test results. Prototype positive control wells (PCW) containing recombinant malaria antigens have been developed to identify poor-quality RDT lots. This study assessed community and facility health workers' (HW) ability to use PCWs to detect degraded RDTs, the impact of PCW availability on RDT use and prescribing, and preferred strategies for implementation in Lao People's Democratic Republic (Laos) and Uganda. A total of 557 HWs participated in Laos (267) and Uganda (290). After training, most (88% to ≥ 99%) participants correctly performed the six key individual PCW steps; performance was generally maintained during the 6-month study period. Nearly all (97%) reported a correct action based on PCW use at routine work sites. In Uganda, where data for 127,775 individual patients were available, PCW introduction in health facilities was followed by a decrease in antimalarial prescribing for RDT-negative patients ≥ 5 years of age (4.7-1.9%); among community-based HWs, the decrease was 12.2% ( P malaria-endemic areas are able to use prototype PCWs for quality control of malaria RDTs. PCW availability can improve HWs' confidence in RDT results, and benefit malaria diagnostic programs. Lessons learned from this study may be valuable for introduction of other point-of-care diagnostic and quality-control tools. Future work should evaluate longer term impacts of PCWs on patient management. © The American Society of Tropical Medicine and Hygiene.

  2. Evaluation of Titanium Alloys Fabricated Using Rapid Prototyping Technologies—Electron Beam Melting and Laser Beam Melting

    Directory of Open Access Journals (Sweden)

    Toru Okabe

    2011-10-01

    Full Text Available This study characterized properties of Ti-6Al-4V ELI (extra low interstitial, ASTM grade 23 specimens fabricated by a laser beam melting (LBM and an electron beam melting (EBM system for dental applications. Titanium alloy specimens were made into required size and shape for each standard test using fabrication methods. The LBM specimens were made by an LBM machine utilizing 20 µm of Ti-6Al-4V ELI powder. Ti-6Al-4V ELI specimens were also fabricated by an EBM using 40 µm of Ti-6Al-4V ELI powder (average diameter, 40 µm: Arcam ABÒ in a vacuum. As a control, cast Ti-6Al-4V ELI specimens (Cast were made using a centrifugal casting machine in an MgO-based mold. Also, a wrought form of Ti-6Al-4V ELI (Wrought was used as a control. The mechanical properties, corrosion properties and grindability (wear properties were evaluated and data was analyzed using ANOVA and a non-parametric method (α = 0.05. The strength of the LBM and wrought specimens were similar, whereas the EBM specimens were slightly lower than those two specimens. The hardness of both the LBM and EBM specimens was similar and slightly higher than that of the cast and wrought alloys. For the higher grindability speed at 1,250 m/min, the volume loss of Ti64 LBM and EBM showed no significant differences among all the fabrication methods. LBM and EBM exhibited favorable results in fabricating dental appliances with excellent properties as found for specimens made by other fabricating methods.

  3. RAPID SEPARATION METHOD FOR EMERGENCY WATER AND URINE SAMPLES

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, S.; Culligan, B.

    2008-08-27

    The Savannah River Site Environmental Bioassay Lab participated in the 2008 NRIP Emergency Response program administered by the National Institute for Standards and Technology (NIST) in May, 2008. A new rapid column separation method was used for analysis of actinides and {sup 90}Sr the NRIP 2008 emergency water and urine samples. Significant method improvements were applied to reduce analytical times. As a result, much faster analysis times were achieved, less than 3 hours for determination of {sup 90}Sr and 3-4 hours for actinides. This represents a 25%-33% improvement in analysis times from NRIP 2007 and a {approx}100% improvement compared to NRIP 2006 report times. Column flow rates were increased by a factor of two, with no significant adverse impact on the method performance. Larger sample aliquots, shorter count times, faster cerium fluoride microprecipitation and streamlined calcium phosphate precipitation were also employed. Based on initial feedback from NIST, the SRS Environmental Bioassay Lab had the most rapid analysis times for actinides and {sup 90}Sr analyses for NRIP 2008 emergency urine samples. High levels of potential matrix interferences may be present in emergency samples and rugged methods are essential. Extremely high levels of {sup 210}Po were found to have an adverse effect on the uranium results for the NRIP-08 urine samples, while uranium results for NRIP-08 water samples were not affected. This problem, which was not observed for NRIP-06 or NRIP-07 urine samples, was resolved by using an enhanced {sup 210}Po removal step, which will be described.

  4. A method for rapid similarity analysis of RNA secondary structures

    Directory of Open Access Journals (Sweden)

    Liu Na

    2006-11-01

    Full Text Available Abstract Background Owing to the rapid expansion of RNA structure databases in recent years, efficient methods for structure comparison are in demand for function prediction and evolutionary analysis. Usually, the similarity of RNA secondary structures is evaluated based on tree models and dynamic programming algorithms. We present here a new method for the similarity analysis of RNA secondary structures. Results Three sets of real data have been used as input for the example applications. Set I includes the structures from 5S rRNAs. Set II includes the secondary structures from RNase P and RNase MRP. Set III includes the structures from 16S rRNAs. Reasonable phylogenetic trees are derived for these three sets of data by using our method. Moreover, our program runs faster as compared to some existing ones. Conclusion The famous Lempel-Ziv algorithm can efficiently extract the information on repeated patterns encoded in RNA secondary structures and makes our method an alternative to analyze the similarity of RNA secondary structures. This method will also be useful to researchers who are interested in evolutionary analysis.

  5. Thermal Modeling and Simulation of Electron Beam Melting for Rapid Prototyping on Ti6Al4V Alloys

    Science.gov (United States)

    Neira Arce, Alderson

    To be a viable solution for contemporary engineering challenges, the use of titanium alloys in a wider range of applications requires the development of new techniques and processes that are able to decrease production cost and delivery times. As a result, the use of material consolidation in a near-net-shape fashion, using dynamic techniques like additive manufacturing by electron beam selective melting EBSM represents a promising method for part manufacturing. However, a new product material development can be cost prohibitive, requiring the use of computer modeling and simulation as a way to decrease turnaround time. To ensure a proper representation of the EBSM process, a thermophysical material characterization and comparison was first performed on two Ti6Al4V powder feedstock materials prepared by plasma (PREP) and gas atomized (GA) processes. This evaluation comprises an evaluation on particle size distribution, density and powder surface area, collectively with the temperature dependence on properties such as heat capacity, thermal diffusivity, thermal conductivity and surface emissivity. Multiple techniques were employed in this evaluation, including high temperature differential scanning calorimetry (HT-DSC), laser flash analysis (LFA), infrared remote temperature analysis (IR-Thermography), laser diffraction, liquid and gas pycnometry using mercury and krypton adsorption respectively. This study was followed by the review of complementary strategies to simulate the temperature evolution during the EBSM process, using a finite element analysis package called COMSOL Multiphysics. Two alternatives dedicated to representing a moving heat source (electron beam) and the powder bed were developed using a step-by-step approximation initiative. The first method consisted of the depiction of a powder bed discretized on an array of domains, each one representing a static melt pool, where the moving heat source was illustrated by a series of time dependant selective

  6. Benchtop chemistry for the rapid prototyping of label-free biosensors: Transmission localized surface plasmon resonance platforms

    Science.gov (United States)

    Liao, Wei-Ssu; Chen, Xin; Yang, Tinglu; Castellana, Edward T.; Chen, Jixin; Cremer, Paul S.

    2012-01-01

    Herein, a simple label-free biosensor fabrication method is demonstrated based on transmission localized surface plasmon resonance (T-LSPR). The platform, which consists of a silver nanoparticle array, can be prepared in just a few minutes using benchtop chemistry. The array was made by a templating technique in conjunction with the photoreduction of Ag ions from solution. This metal surface was functionalized with biotin-linked thiol ligands for binding streptavidin molecules from solution. For an array of 19 nm diameter silver nanoparticles, a redshift in the T-LSPR spectrum of 24 nm was observed upon protein-ligand binding at saturation. The binding constant was found to be 2 × 1012 M–1. Platforms were also fabricated with silver nanoparticles of 34, 55, and 72 nm diameters. The maximum LSPR wavelength shift was nanoparticle size dependent and the maximum sensitivity was obtained with the smaller nanoparticles. PMID:20408728

  7. Architectural prototyping

    DEFF Research Database (Denmark)

    Bardram, Jakob Eyvind; Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2004-01-01

    A major part of software architecture design is learning how specific architectural designs balance the concerns of stakeholders. We explore the notion of "architectural prototypes", correspondingly architectural prototyping, as a means of using executable prototypes to investigate stakeholders......' concerns with respect to a system under development. An architectural prototype is primarily a learning and communication vehicle used to explore and experiment with alternative architectural styles, features, and patterns in order to balance different architectural qualities. The use of architectural...... prototypes in the development process is discussed, and we argue that such prototypes can play a role throughout the entire process. The use of architectural prototypes is illustrated by three distinct cases of creating software systems. We argue that architectural prototyping can provide key insights...

  8. Architectural Prototyping

    DEFF Research Database (Denmark)

    Bardram, Jakob; Christensen, Henrik Bærbak; Hansen, Klaus Marius

    2004-01-01

    A major part of software architecture design is learning how specific architectural designs balance the concerns of stakeholders. We explore the notion of "architectural prototypes", correspondingly architectural prototyping, as a means of using executable prototypes to investigate stakeholders......' concerns with respect to a system under development. An architectural prototype is primarily a learning and communication vehicle used to explore and experiment with alternative architectural styles, features, and patterns in order to balance different architectural qualities. The use of architectural...... prototypes in the development process is discussed, and we argue that such prototypes can play a role throughout the entire process. The use of architectural prototypes is illustrated by three distinct cases of creating software systems. We argue that architectural prototyping can provide key insights...

  9. A rapid and specific colorimetric method for free tryptophan quantification.

    Science.gov (United States)

    Wu, Yinan; Wang, Tianmin; Zhang, Chong; Xing, Xin-Hui

    2018-01-01

    Tryptophan is one of the eight essential amino acids and plays an important role in many biological processes. For its interaction with human health, environment and relevant commercial interest in biotechnology-based production, rapid and specific quantification method for this molecule accessible to common laboratories is badly needed. We herein reported a simple colorimetric method for free tryptophan quantification with 96-well-plate-level throughput. Our protocol firstly converted tryptophan to indole enzymatically by purified tryptophanases and then used reactivity of indole with hydroxylamine to form pink product with absorption peak at 530nm, enabling the quantification of tryptophan with simple spectrometry in just two hours. We presented that this method exhibited a linear detection range from 100μM to 600μM (R(2) = 0.9969) with no detection towards other naturally occurring tryptophan analogs or tryptophan residues in proteins. It was very robust in complicated biological samples, as demonstrated by quantifying the titer of 36 mutated tryptophan-producing strains with Pearson correlation coefficient of 0.93 in contrast to that measured by high performance liquid chromatography (HPLC). Our method should be potent for routine free tryptophan quantification in a high-throughput manner, facilitating studies in medicine, microbiology, food chemistry, metabolic engineering, etc. Copyright © 2017. Published by Elsevier B.V.

  10. An Investigation into the Trueness and Precision of Copy Denture Templates Produced by Rapid Prototyping and Conventional Means.

    Science.gov (United States)

    Davda, K; Osnes, C; Dillon, S; Wu, J; Hyde, P; Keeling, A

    2017-12-01

    To assess the trueness and precision of copy denture templates produced using traditional methods and 3D printing. Six copies of a denture were made using: 1. Conventional technique with silicone putty in an impression tray (CT). 2. Conventional technique with no impression tray (CNT). 3. 3D scanning and printing (3D). Scan trueness and precision was investigated by scanning a denture six times and comparing five scans to the sixth. Then the scans of the six CT, CNT and 3D dentures were compared by aligning, in turn, the copies of each denture to the scanned original. Outcome measures were the mean surface-to-surface distance, standard deviation of that distance and the maximum distance. Student's unpaired t-tests with Bonferroni correction were used to analyse the results. The repeated scans of the original denture showed a scan trueness of 0.013mm (SD 0.002) and precision of 0.013mm (SD 0.002). Trueness: CT templates, 0.168mm (0.047), CNT templates 0.195mm (0.034) and 3D 0.103mm (0.021). Precision: CT templates 0.158mm (0.037), CNT 0.233mm (0.073), 3D 0.090mm (0.017). For each outcome measure the 3D templates demonstrated an improvement which was statistically significant (p⟨0.05). 3D printed copy denture templates reproduced the original with greater trueness and precision than conventional techniques. Copyright© 2017 Dennis Barber Ltd.

  11. Rapid identification of cytokinins by an immunological method

    Energy Technology Data Exchange (ETDEWEB)

    Morris, R.O.; Jameson, P.E.; Morris, J.W. (Univ. of Missouri-Columbia (USA)); Laloue, M. (Centre Nationale de la Recherche Scientifique, Gif-sur-Yvette (France))

    1991-04-01

    A method for rapid identification of bacterial cytokinins has been developed in which cultures are fed ({sup 3}H)adenine, the cytokinins (including, {sup 3}H-labeled cytokinins) are isolated by immunoaffinity chromatography, and analyzed by HPLC with on-line scintillation counting. Analysis of Agrobacterium tumefaciens strains showed that some produced primarily trans-zeatin, whereas others produced primarily trans-zeatin riboside. Pseudomonas syringae pv savastanoi produced mixtures of transzeatin, dihydrozeatin, 1{double prime}-methyl-trans-zeatin riboside, and other unknown cytokinin-like substances. Corynebacterium fascians, produced cis-zeatin, isopentenyladenine and isopentenyladenosine. The technique is designed for qualitative rather than quantitative studies and allows ready identification of bacterial cytokinins. It may also have utility in the study of plant cytokinins if adequate incorporation of label into cytokinin precursor pools can be achieved.

  12. A rapid protection switching method in carrier ethernet ring networks

    Science.gov (United States)

    Yuan, Liang; Ji, Meng

    2008-11-01

    Abstract: Ethernet is the most important Local Area Network (LAN) technology since more than 90% data traffic in access layer is carried on Ethernet. From 10M to 10G, the improving Ethernet technology can be not only used in LAN, but also a good choice for MAN even WAN. MAN are always constructed in ring topology because the ring network could provide resilient path protection by using less resource (fibre or cable) than other network topologies. In layer 2 data networks, spanning tree protocol (STP) is always used to protect transmit link and preventing the formation of logic loop in networks. However, STP cannot guarantee the efficiency of service convergence when link fault happened. In fact, convergent time of networks with STP is about several minutes. Though Rapid Spanning Tree Protocol (RSTP) and Multi-Spanning Tree Protocol (MSTP) improve the STP technology, they still need a couple of seconds to achieve convergence, and can not provide sub-50ms protection switching. This paper presents a novel rapid ring protection method (RRPM) for carrier Ethernet. Unlike other link-fault detection method, it adopts distributed algorithm to detect link fault rapidly (sub-50ms). When networks restore from link fault, it can revert to the original working state. RRPM can provide single ring protection and interconnected ring protection without the formation of super loop. In normal operation, the master node blocks the secondary port for all non-RRPM Ethernet frames belonging to the given RRPM Ring, thereby avoiding a loop in the ring. When link fault happens, the node on which the failure happens moves from the "ring normal" state to the "ring fault" state. It also sends "link down" frame immediately to other nodes and blocks broken port and flushes its forwarding database. Those who receive "link down" frame will flush forwarding database and master node should unblock its secondary port. When the failure restores, the whole ring will revert to the normal state. That is

  13. Application of computer-aided three-dimensional skull model with rapid prototyping technique in repair of zygomatico-orbito-maxillary complex fracture.

    Science.gov (United States)

    Li, Wei Zhong; Zhang, Mei Chao; Li, Shao Ping; Zhang, Lei Tao; Huang, Yu

    2009-06-01

    With the advent of CAD/CAM and rapid prototyping (RP), a technical revolution in oral and maxillofacial trauma was promoted to benefit treatment, repair of maxillofacial fractures and reconstruction of maxillofacial defects. For a patient with zygomatico-facial collapse deformity resulting from a zygomatico-orbito-maxillary complex (ZOMC) fracture, CT scan data were processed by using Mimics 10.0 for three-dimensional (3D) reconstruction. The reduction design was aided by 3D virtual imaging and the 3D skull model was reproduced using the RP technique. In line with the design by Mimics, presurgery was performed on the 3D skull model and the semi-coronal incision was taken for reduction of ZOMC fracture, based on the outcome from the presurgery. Postoperative CT and images revealed significantly modified zygomatic collapse and zygomatic arch rise and well-modified facial symmetry. The CAD/CAM and RP technique is a relatively useful tool that can assist surgeons with reconstruction of the maxillofacial skeleton, especially in repairs of ZOMC fracture.

  14. Characterization of rapidly-prototyped, battery-operated, argon-hydrogen microplasma on a hybrid chip for elemental analysis of microsamples by portable optical emission spectrometry

    Science.gov (United States)

    Weagant, Scott; Dulai, Gurjit; Li, Lu; Karanassios, Vassili

    2015-04-01

    A rapidly-prototyped, battery-operated, atmospheric-pressure, self-igniting Ar-H2 microplasma was interfaced to a portable fiber-optic spectrometer. The microplasma-spectrometer combination was used to document the spectral lines emitted when μL of dilute solutions of single element standards of Ag, Ba, Ca, Eu, Pd, Rb and Sr were first dried and then vaporized into the microplasma. A small-size, electrothermal vaporization system was used for microsample introduction. Identification of the prominent spectral lines for these elements is reported. It was found that the most prominent spectral line for Ba, Ca and Sr was different than that emitted from an inductively coupled plasma (ICP). In general, prominent spectral lines with low excitation energy were dominating, thus resulting in spectra simpler than those emitted from an ICP. Detection limits were between 45 and 180 pg (expressed in absolute amounts). When expressed in relative concentration units, they ranged between 15 and 60 μg/L (obtained using 3 μL diluted standards). Calibration curves were linear (on the average) for 1.5 orders-of-magnitude. Average precision was 15%. Analytical capability and utility was demonstrated using the determination of Ca and Mg in (medicinal) thermal spring water.

  15. Autotransplantation of teeth using computer-aided rapid prototyping of a three-dimensional replica of the donor tooth: a systematic literature review.

    Science.gov (United States)

    Verweij, J P; Jongkees, F A; Anssari Moin, D; Wismeijer, D; van Merkesteyn, J P R

    2017-11-01

    This systematic review provides an overview of studies on autotransplantation techniques using rapid prototyping for preoperative fabrication of donor tooth replicas for preparation of the neo-alveolus. Different three-dimensional autotransplantation techniques and their treatment outcomes are discussed. The systematic literature search yielded 19 articles that satisfied the criteria for inclusion. These papers described one case-control study, four clinical observational studies, one study with a clinical and in vitro part, four in vitro studies, and nine case reports. The in vitro studies reported high accuracy for the printing and planning processes. The case reports all reported successful transplantation without any pathological signs. The clinical studies reported a short extraoral time of the donor tooth, with subsequent success and survival rates of 80.0-91.1% and 95.5-100%, respectively. The case-control study reported a significant decrease in extraoral time and high success rates with the use of donor tooth replicas. In conclusion, the use of a preoperatively designed surgical guide for autotransplantation enables accurate positional planning, increases the ease of surgery, and decreases the extraoral time. However, the quality of the existing body of evidence is low. Further research is therefore required to investigate the clinical advantages of this innovative autotransplantation technique. Copyright © 2017 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  16. Methods and Results for a Global Precipitation Measurement (GPM) Validation Network Prototype

    Science.gov (United States)

    Morris, Kenneth R.; Schwaller, Mathew R.

    2010-01-01

    As one component of a ground validation system to meet requirements for the upcoming Global Precipitation Measurement (GPM) mission, a quasi-operational prototype a system to compare satellite- and ground-based radar measurements has been developed. This prototype, the GPM Validation Network (VN), acquires data from the Precipitation Radar (PR) on the Tropical Rainfall Measuring Mission (TRMM) satellite and from ground radar (GR) networks in the continental U.S. and participating international sites. PR data serve as a surrogate for similar observations from the Dual-frequency Precipitation Radar (DPR) to be present on GPM. Primary goals of the VN prototype are to understand and characterize the variability and bias of precipitation retrievals between the PR and GR in various precipitation regimes at large scales, and to improve precipitation retrieval algorithms for the GPM instruments. The current VN capabilities concentrate on comparisons of the base reflectivity observations between the PR and GR, and include support for rain rate comparisons. The VN algorithm resamples PR and GR reflectivity and other 2-D and 3-D data fields to irregular common volumes defined by the geometric intersection of the instrument observations, and performs statistical comparisons of PR and GR reflectivity and estimated rain rates. Algorithmic biases and uncertainties introduced by traditional data analysis techniques are minimized by not performing interpolation or extrapolation of data to a fixed grid. The core VN dataset consists of WSR-88D GR data and matching PR orbit subset data covering 21 sites in the southeastern U. S., from August, 2006 to the present. On average, about 3.5 overpass events per month for these WSR-88D sites meet VN criteria for significant precipitation, and have matching PR and GR data available. This large statistical sample has allowed the relative calibration accuracy and stability of the individual ground radars, and the quality of the PR reflectivity

  17. Prototyping Practice

    DEFF Research Database (Denmark)

    Ramsgaard Thomsen, Mette; Tamke, Martin

    2015-01-01

    This paper examines the role of the prototyping in digital architecture. During the past decade, a new research field has emerged exploring the digital technology’s impact on the way we think, design and build our environment. In this practice the prototype, the pavilion, installation...... or demonstrator, has become a shared research tool. This paper asks how this practice has formed by tracing the different roles of the prototype from ideation and design, to analysis and evaluation. Taking point of departure in CITA’s own prototyping practice, we explore the relationships between physical...... and digital prototyping as a particular means of validation and verification. Here, a breadth of physical prototypes take on varying roles, in turn informing, testing and proving the research enquiry. The paper addresses how we can differentiate between these modes of prototyping and how....

  18. Micro-Rapid Prototyping Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of this task is to create a maskless process for sample 500 µm 3-D objects. Specific objectives are to(1) Develop 3-D CAD computer models and...

  19. Rapid prototyping in aortic surgery.

    Science.gov (United States)

    Bangeas, Petros; Voulalas, Grigorios; Ktenidis, Kiriakos

    2016-04-01

    3D printing provides the sequential addition of material layers and, thus, the opportunity to print parts and components made of different materials with variable mechanical and physical properties. It helps us create 3D anatomical models for the better planning of surgical procedures when needed, since it can reveal any complex anatomical feature. Images of abdominal aortic aneurysms received by computed tomographic angiography were converted into 3D images using a Google SketchUp free software and saved in stereolithography format. Using a 3D printer (Makerbot), a model made of polylactic acid material (thermoplastic filament) was printed. A 3D model of an abdominal aorta aneurysm was created in 138 min, while the model was a precise copy of the aorta visualized in the computed tomographic images. The total cost (including the initial cost of the printer) reached 1303.00 euros. 3D imaging and modelling using different materials can be very useful in cases when anatomical difficulties are recognized through the computed tomographic images and a tactile approach is demanded preoperatively. In this way, major complications during abdominal aorta aneurysm management can be predicted and prevented. Furthermore, the model can be used as a mould; the development of new, more biocompatible, less antigenic and individualized can become a challenge in the future. © The Author 2016. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

  20. Method for Rapid Protein Identification in a Large Database

    Directory of Open Access Journals (Sweden)

    Wenli Zhang

    2013-01-01

    Full Text Available Protein identification is an integral part of proteomics research. The available tools to identify proteins in tandem mass spectrometry experiments are not optimized to face current challenges in terms of identification scale and speed owing to the exponential growth of the protein database and the accelerated generation of mass spectrometry data, as well as the demand for nonspecific digestion and post-modifications in complex-sample identification. As a result, a rapid method is required to mitigate such complexity and computation challenges. This paper thus aims to present an open method to prevent enzyme and modification specificity on a large database. This paper designed and developed a distributed program to facilitate application to computer resources. With this optimization, nearly linear speedup and real-time support are achieved on a large database with nonspecific digestion, thus enabling testing with two classical large protein databases in a 20-blade cluster. This work aids in the discovery of more significant biological results, such as modification sites, and enables the identification of more complex samples, such as metaproteomics samples.

  1. A Rasch model prototype for assessing vocabulary learning resulting from different instructional methods: a preschool example.

    Science.gov (United States)

    Leung, Cynthia B; Lang, William Steve

    2009-01-01

    This study explored the effects of using Rasch modeling to analyze data on vocabulary knowledge of preschoolers who participated in repeated read-aloud events and hands-on science activities with their classroom teachers. A Rasch prototype for literacy research was developed and applied to the preschool data. Thirty-one target words were selected for analysis from three children's informational picture books on light and color. After different instructional activities, each child received scores on individual target words measured with a total of six assessments, including free response vocabulary tests and expressive and receptive picture vocabulary tests. Rasch modeling was used to assess the learning difficulty of target words in different instructional settings. Suggestions are made for applying Rasch modeling to classroom studies of instructional interventions.

  2. Deviation analysis of C1-C2 transarticular screw placement assisted by a novel rapid prototyping drill template: a cadaveric study.

    Science.gov (United States)

    Hu, Yong; Yuan, Zhen-Shan; Kepler, Christopher K; Albert, Todd J; Yuan, Jian-Bing; Dong, Wei-Xin; Sun, Xiao-Yang; Wang, Cheng-Tao

    2014-07-01

    Cadaveric study. The aim of this study was to develop and validate the accuracy of a novel navigational template for C1-C2 transarticular screw (C1C2TAS) placement in cadaveric specimens. Currently, C1C2TASs are primarily positioned using a free-hand technique or under fluoroscopic guidance. Screw placement is challenging owing to the small size of the C2 isthmus, which places technical demands on the surgeon. Screw insertion carries a potential risk of neurovascular injury, magnifying the importance of using a precise technique for screw insertion. Computed tomography (CT) scans with 0.625-mm wide cuts were obtained from the 32 cadaveric cervical specimens. The CT data were imported into a computer navigation system. We developed 32 three-dimensional drill templates, which were created by computer modeling using a rapid prototyping technique based on the CT data. We constructed drill templates using a custom trajectory for each level and side based on specimen anatomy. The drill templates were used to guide establishment of a pilot hole for screw placement. The entry point and angular direction of the intended screw positions and inserted screw positions were measured by comparing postoperative and preoperative images after the coordinate axes were synchronized. The average displacement of the entry point of the left and right C1C2TAS in the x-, y-, and z-axis was 0.13±0.90 mm, 0.50±1.50 mm, and -0.22±0.71 mm on the left, and 0.21±1.03 mm, 0.46±1.55 mm, and -0.29±0.58 mm on the right. There was no statistically significant difference in entry point and direction between the intended and actual screw trajectory. The small deviations seen are likely due to human error in the form of small variations in the surgical technique and use of software to design the prototype. This technology improves the safety profile of this fixation technique and should be further studied in clinical applications.

  3. A Formal Method for Semantics-Based Change-Merging of Software Prototypes

    Science.gov (United States)

    1994-06-01

    understanding of requirements early in the conceptual design phase of development. It involves the use of software tools to rapidly create concrete executable...Algorithm merge.ezpressions Algorithm merge.output-guard- mapa (VERTS : id-.et; BASE, A, B: out-guard.map) re- turn out.guard.map MERGE: out-guard-map;, op

  4. Solution Prototype

    DEFF Research Database (Denmark)

    Efeoglu, Arkin; Møller, Charles; Serie, Michel

    2013-01-01

    This paper outlines an artifact building and evaluation proposal. Design Science Research (DSR) studies usually consider encapsulated artifact that have relationships with other artifacts. The solution prototype as a composed artifact demands for a more comprehensive consideration in its systematic...... environment. The solution prototype that is composed from blending product and service prototype has particular impacts on the dualism of DSR’s “Build” and “Evaluate”. Since the mix between product and service prototyping can be varied, there is a demand for a more agile and iterative framework. Van de Ven...

  5. Prototyping Revisited

    DEFF Research Database (Denmark)

    Hansen, Poul H. Kyvsgård; Hansen, Svend Aage; Hansen, Erik

    2006-01-01

    Until now, prototyping has been developing as a technological discipline. In so it has proven to be a strong means to test specific solutions or physical designs before the launch of a product. The results have been reduced development time and improvement of quality in a broad sense. There are......, however, indications that we should review our perception of prototypes to be broader and to view our application of prototypes in a broader organizational view. This paper presents an initial and explorative review of the changing role of prototypes in product development....

  6. Accurate reconstruction of discontinuous mandible using a reverse engineering/computer-aided design/rapid prototyping technique: a preliminary clinical study.

    Science.gov (United States)

    Zhou, Li-bin; Shang, Hong-tao; He, Li-sheng; Bo, Bin; Liu, Gui-cai; Liu, Yan-pu; Zhao, Jin-long

    2010-09-01

    To improve the reconstructive surgical outcome of a discontinuous mandibular defect, we used reverse engineering (RE), computer-aided design (CAD), and rapid prototyping (RP) technique to fabricate customized mandibular trays to precisely restore the mandibular defects. Autogenous bone grafting was also used to restore the bony continuity for occlusion rehabilitation. Six patients who had undergone block resection of the mandible underwent reconstruction using a custom titanium tray combining autogenous iliac grafts. The custom titanium tray was made using a RE/CAD/RP technique. A virtual 3-dimensional model was obtained by spiral computed tomography scanning. The opposite side of the mandible was mirrored to cover the defect area to restore excellent facial symmetry. A bone grafting tray was designed from the mirrored image and manufactured using RP processing and casting. The mandibular defects were restored using the trays in combination of autologous iliac grafting. An implant denture was made for 1 of the 6 patients at 24 weeks postoperatively for occlusion rehabilitation. The trays fabricated using this technique fit well in all 6 patients. The reconstructive procedures were easy and time saving. Satisfactory facial symmetry was restored. No severe complications occurred in the 5 patients without occlusion rehabilitation during a mean 50-month follow-up period. The reconstruction in the patient with occlusion lasted for only 1 year and failed eventually because of bone resorption and infection. Mandibular reconstruction was facilitated using the RE/CAD/RP technique. Satisfactory esthetic results were achieved. However, the rigidity of the cast tray could cause severe stress shielding to the grafts, which could lead to disuse atrophy. Therefore, some modification is needed for functional reconstruction. Copyright 2010 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

  7. Final report on LDRD project: Low-cost Pd-catalyzed metallization technology for rapid prototyping of electronic substrates and devices

    Energy Technology Data Exchange (ETDEWEB)

    Chen, K.S.; Morgan, W.P.; Zich, J.L.

    1998-02-01

    A low-cost, thermally-activated, palladium-catalyzed metallization process was developed for rapid prototyping of polymeric electronic substrates and devices. The process was successfully applied in producing adhesiveless copper/polyimide laminates with high peel strengths and thick copper coating; copper/polyimide laminates are widely used in fabricating interconnects such as printed wiring boards (PWBs) and flexible circuits. Also successfully metallized using this low-cost metallization process were: (1) scaled-down models of radar-and-communication antenna and waveguide; (2) scaled-down model of pulsed-power-accelerator electrode; (3) three-dimensional micro-porous, open-cell vitreous carbon foams. Moreover, additive patterned metallization was successfully achieved by selectively printing or plotting the catalyst ink only on areas where metallization is desired, and by uniform thermal activation. Additive patterned metallization eliminates the time-consuming, costly and environmentally-unfriendly etching process that is routinely carried out in conventional subtractive patterned metallization. A metallization process via ultraviolet (UV) irradiation activation was also demonstrated. In this process palladium-catalyst solution is first uniformly coated onto the substrate. A masking pattern is used to cover the areas where metallization is not wanted. UV irradiation is applied uniformly to activate the palladium catalyst and to cure the polymer carrier in areas that are not covered by the mask. Metal is then deposited by electroless plating only or by a combination of electroless and electrolytic plating. This UV-activation technique is particularly useful in additive fine-line patterned metallization. Lastly, computer models for electrolytic and electroless plating processes were developed to provide guidance in plating-process design.

  8. Reconstruction of large cranial defects with poly-methyl-methacrylate (PMMA) using a rapid prototyping model and a new technique for intraoperative implant modeling.

    Science.gov (United States)

    Unterhofer, Claudia; Wipplinger, Christoph; Verius, Michael; Recheis, Wolfgang; Thomé, Claudius; Ortler, Martin

    Reconstruction of large cranial defects after craniectomy can be accomplished by free-hand poly-methyl-methacrylate (PMMA) or industrially manufactured implants. The free-hand technique often does not achieve satisfactory cosmetic results but is inexpensive. In an attempt to combine the accuracy of specifically manufactured implants with low cost of PMMA. Forty-six consecutive patients with large skull defects after trauma or infection were retrospectively analyzed. The defects were reconstructed using computer-aided design/computer-aided manufacturing (CAD/CAM) techniques. The computer file was imported into a rapid prototyping (RP) machine to produce an acrylonitrile-butadiene-styrene model (ABS) of the patient's bony head. The gas-sterilized model was used as a template for the intraoperative modeling of the PMMA cranioplasty. Thus, not the PMMA implant was generated by CAD/CAM technique but the model of the patients head to easily form a well-fitting implant. Cosmetic outcome was rated on a six-tiered scale by the patients after a minimum follow-up of three months. The mean size of the defect was 74.36cm2. The implants fitted well in all patients. Seven patients had a postoperative complication and underwent reoperation. Mean follow-up period was 41 months (range 2-91 months). Results were excellent in 42, good in three and not satisfactory in one patient. Costs per implant were approximately 550 Euros. PMMA implants fabricated in-house by direct molding using a bio-model of the patients bony head are easily produced, fit properly and are inexpensive compared to cranial implants fabricated with other RP or milling techniques. Copyright © 2017 Polish Neurological Society. Published by Elsevier Urban & Partner Sp. z o.o. All rights reserved.

  9. RAPID TEST METHOD FOR EVALUATION OF ANTIFREEZE ADDITIVE EFFICIENCY

    Directory of Open Access Journals (Sweden)

    S. V. Gushchin

    2015-01-01

    Full Text Available Usage of chemical additives while executing concrete works at negative temperatures is considered as a convenient and economical method. Range of the used antifreeze additives is rather wide. A great number of new additives are advertised but their characteristics have not been practically studied. Evaluation of the antifreeze additive efficiency is unfortunately rather long process and it does not provide comprehensive data on concrete structure formation processes. Due to this development of rapid and comprehensive methodology for construction companies is urgently required.Freezing processes of antifreeze additive aqueous solutions and hardening of cement paste with them have been investigated in the paper. The paper proposes a methodology for determination of freezing point for aqueous solutions of chemical additives of various applications. Identity of  freezing point for a chemical additive aqueous solution and cement paste with an equal concentration of the additive in the paste pore fluid has been determined while taking  calcium nitrate and sodium formate additives as an example. The paper demonstrates the possibility to evaluate efficiency of antifreeze additive action on the basis of kinetics in temperature changes of the cement paste with additives by its consecutive freezing and defrosting.  A methodology for operational evaluation in the field of chemical additive application for concreting items at negative temperatures has been offered in the paper.  The methodology does not require  deficient and expensive test-equipment. It can be applied at ordinary construction companies and it is comprehensible for personnel of low-qualification.  The paper shows the possibility to develop an original methodology for designing concrete structure which is based on operating efficiency determinations  for single and integrated antifreeze additives.

  10. A new rapid method for rockfall energies and distances estimation

    Science.gov (United States)

    Giacomini, Anna; Ferrari, Federica; Thoeni, Klaus; Lambert, Cedric

    2016-04-01

    and distances at the base to block and slope features. The validation of the proposed approach was conducted by comparing predictions to experimental data collected in the field and gathered from the scientific literature. The method can be used for both natural and constructed slopes and easily extended to more complicated and articulated slope geometries. The study shows its great potential for a quick qualitative hazard assessment providing indication about impact energy and horizontal distance of the first impact at the base of a rock cliff. Nevertheless, its application cannot substitute a more detailed quantitative analysis required for site-specific design of mitigation measures. Acknowledgements The authors gratefully acknowledge the financial support of the Australian Coal Association Research Program (ACARP). References Dorren, L.K.A. (2003) A review of rockfall mechanics and modelling approaches, Progress in Physical Geography 27(1), 69-87. Agliardi, F., Crosta, G.B., Frattini, P. (2009) Integrating rockfall risk assessment and countermeasure design by 3D modelling techniques. Natural Hazards and Earth System Sciences 9(4), 1059-1073. Ferrari, F., Thoeni, K., Giacomini, A., Lambert, C. (2016) A rapid approach to estimate the rockfall energies and distances at the base of rock cliffs. Georisk, DOI: 10.1080/17499518.2016.1139729.

  11. Rapid Methods for detection of Veterinary Drug residues in Meat

    Directory of Open Access Journals (Sweden)

    Chandan

    2010-10-01

    methodologies, the variety of residues to search per sample and the need to invest on powerful new instruments for identification and confirmatory purposes. Rapid and versatile screening methodologies make its control easier and reduce the number of non-compliant samples to be confirmed through tedious and costly confirmatory analytical methodologies. For instance, the multiresidue analysis can be performed better by using fast LC methods. Thus, the availability of new screening methodologies and the improvement of the existing ones will contribute to a better safety assurance of meat and other foods of animal origin. [Vet. World 2010; 3(5.000: 241-246

  12. Comparison of the Accuracy of 3D Printed Prototypes Using the Stereolithography (SLA Method with the Digital CAD Models

    Directory of Open Access Journals (Sweden)

    Yankov Emil

    2017-01-01

    Full Text Available Each printing method and the materials used for prototype construction have distinct advantages and drawbacks. A large part of the 3D printer producers indicates high printing accuracy (positioning accuracies from 100 μm up to 1 μm and layer thickness from 100 μm tо 5 μm. In the process of layers deposition, the material is softened, melted or irradiated with a certain light source to polymerize. Thus, during the printing process, the volume of the materials is changing causing shrinking or expansion which often leads to the occurrence of precision errors in the prototype as opposed to the digital model. This phenomenon leads to distortions of the printed object known as a curling effect. Certain chemical compounds are added by the producers to multiple materials in order to enhance their mechanical and technological properties. However, this often results in changes of some printing parameters influencing the precision and quality of the manufactured object. The aim of the particular study is to establish the allowances with regard to the accuracy during manufacturing precise objects used in micro technologies as well as the necessary adjustments in dimensions because of the shrinkage and the positioning of the SLA 3D printed parts from photopolymer material.

  13. Computer-Aided Designing and Manufacturing of Lingual Fixed Orthodontic Appliance Using 2D/3D Registration Software and Rapid Prototyping

    Directory of Open Access Journals (Sweden)

    Soon-Yong Kwon

    2014-01-01

    Full Text Available The availability of 3D dental model scanning technology, combined with the ability to register CBCT data with digital models, has enabled the fabrication of orthognathic surgical CAD/CAM designed splints, customized brackets, and indirect bonding systems. In this study, custom lingual orthodontic appliances were virtually designed by merging 3D model images with lateral and posterior-anterior cephalograms. By exporting design information to 3D CAD software, we have produced a stereolithographic prototype and converted it into a cobalt-chrome alloy appliance as a way of combining traditional prosthetic investment and cast techniques. While the bonding procedure of the appliance could be reinforced, CAD technology simplified the fabrication process by eliminating the soldering phase. This report describes CAD/CAM fabrication of the complex anteroposterior lingual bonded retraction appliance for intrusive retraction of the maxillary anterior dentition. Furthermore, the CAD/CAM method eliminates the extra step of determining the lever arm on the lateral cephalograms and subsequent design modifications on the study model.

  14. Rapid method for identification of transgenic fish zygosity

    Directory of Open Access Journals (Sweden)

    . Alimuddin

    2007-07-01

    Full Text Available Identification of zygosity in transgenik fish is normally achieved by PCR analysis with genomic DNA template extracted from the tissue of progenies which are derived by mating the transgenic fish and wild-type counterpart.  This method needs relatively large amounts of fish material and is time- and labor-intensive. New approaches addressing this problem could be of great help for fish biotechnologists.  In this experiment, we applied a quantitative real-time PCR (qr-PCR method to analyze zygosity in a stable line of transgenic zebrafish (Danio rerio carrying masu salmon, Oncorhynchus masou D6-desaturase-like gene. The qr-PCR was performed using iQ SYBR Green Supermix in the iCycler iQ Real-time PCR Detection System (Bio-Rad Laboratories, USA.  Data were analyzed using the comparative cycle threshold method.  The results demonstrated a clear-cut identification of all transgenic fish (n=20 classified as a homozygous or heterozygous.  Mating of those fish with wild-type had revealed transgene transmission to the offspring following expected Mendelian laws. Thus, we found that the qTR-PCR to be effective for a rapid and precise determination of zygosity in transgenic fish. This technique could be useful in the establishment of breeding programs for mass transgenic fish production and in experiments in which zygosity effect could have a functional impact. Keywords: quantitative real-time PCR; zygosity; transgenic fish; mass production   ABSTRAK Identifikasi sigositas ikan transgenik biasanya dilakukan menggunakan analisa PCR dengan cetakan DNA genomik yang diekstraksi dari jaringan ikan hasil persilangan antara ikan transgenik dan ikan normal.   Metode ini memerlukan ikan dalam jumlah yang banyak, dan juga waktu serta tenaga.  Pendekatan baru untuk mengatasi masalah tersebut akan memberikan manfaat besar kepada peneliti bioteknologi perikanan.  Pada penelitian ini, kami menggunakan metode PCR real-time kuantitatif (krt-PCR untuk

  15. Prototyping user displays using CLIPS

    Science.gov (United States)

    Kosta, Charles P.; Miller, Ross; Krolak, Patrick; Vesty, Matt

    1990-01-01

    CLIPS is being used as an integral module of a rapid prototyping system. The prototyping system consists of a display manager for object browsing, a graph program for displaying line and bar charts, and a communications server for routing messages between modules. A CLIPS simulation of a physical model provides dynamic control of the user's display. Currently, a project is well underway to prototype the Advanced Automation System (AAS) for the Federal Aviation Administration.

  16. A rapid cloning method employing orthogonal end protection

    NARCIS (Netherlands)

    Jakobi, A.J.|info:eu-repo/dai/nl/311489621; Huizinga, E.G.|info:eu-repo/dai/nl/12314969X

    2012-01-01

    We describe a novel in vitro cloning strategy that combines standard tools in molecular biology with a basic protecting group concept to create a versatile framework for the rapid and seamless assembly of modular DNA building blocks into functional open reading frames. Analogous to chemical

  17. Unikabeton Prototype

    DEFF Research Database (Denmark)

    Søndergaard, Asbjørn; Dombernowsky, Per

    2011-01-01

    The Unikabeton prototype structure was developed as the finalization of the cross-disciplinary research project Unikabeton, exploring the architectural potential in linking the computational process of topology optimisation with robot fabrication of concrete casting moulds. The project was elabor......The Unikabeton prototype structure was developed as the finalization of the cross-disciplinary research project Unikabeton, exploring the architectural potential in linking the computational process of topology optimisation with robot fabrication of concrete casting moulds. The project...... of Architecture was to develop a series of optimisation experiments, concluding in the design and optimisation of a full scale prototype concrete structure....

  18. Prototyping of chemical composition of complex crystals using method of neural networks

    Science.gov (United States)

    Blagin, A. V.; Nefedov, V. V.; Nefedova, N. A.

    2017-10-01

    The traditional methods of study of multi-component crystal heterojunction structures by means of X-ray diffractometry and electroscopy are expensive and complex. The present paper discusses the information technology based on the use of artificial neural networks for identification of the chemical composition of complex semiconductor structures. The obtained results allow supposing the successful use of this method for many multi-component systems.

  19. Rapid Radiochemical Method for Americium-241 in Building ...

    Science.gov (United States)

    Technical Fact Sheet Analysis Purpose: Qualitative analysis Technique: Alpha spectrometry Method Developed for: Americium-241 in building materials Method Selected for: SAM lists this method for qualitative analysis of americium-241 in concrete or brick building materials. Summary of subject analytical method which will be posted to the SAM website to allow access to the method.

  20. Rapid Radiochemical Method for Radium-226 in Building ...

    Science.gov (United States)

    Technical Fact Sheet Analysis Purpose: Qualitative analysis Technique: Alpha spectrometry Method Developed for: Radium-226 in building materials Method Selected for: SAM lists this method for qualitative analysis of radium-226 in concrete or brick building materials Summary of subject analytical method which will be posted to the SAM website to allow access to the method.

  1. Rapid method for plutonium-241 determination in soil samples

    OpenAIRE

    Piekarz, M.; Komosa, A.

    2014-01-01

    A simple and rapid procedure for the determination of plutonium isotopes in the environment is presented. The procedure combines alpha spectrometry, solvent extraction and liquid scintillation measurements to ensure that both alpha- and beta-emitting isotopes are determined. Of five tested extractants, bis-(2-ethylhexyl) phosphoric acid was found to be the best choice. The procedure was applied to soil samples contaminated with Chernobyl fallout.

  2. Applying Agile Design Sprint Methods in Action Design Research: Prototyping a Health and Wellbeing Platform

    NARCIS (Netherlands)

    Keijzer-Broers, W.J.W.; de Reuver, G.A.

    2016-01-01

    In Action Design Research projects, researchers often face severe constraints in terms of budget and time within the practical setting. Therefore, we argue that ADR researchers may adopt efficient methods to guide their design strategy. While agile and sprint oriented design approaches are becoming

  3. Performance of the moving voxel image reconstruction (MVIR) method in the fixed site detection system (FSDS) prototype

    Energy Technology Data Exchange (ETDEWEB)

    Estep, Robert J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2012-05-31

    We have developed a dynamic image reconstruction method called MVIR (Moving Voxel Image Reconstruction) for lane detection in multilane portal monitor systems. MVIR was evaluated for use in the Fixed Site Detection System, a prototype three-lane portal monitor system for EZ-pass toll plazas. As a baseline, we compared MVIR with a static image reconstruction method in analyzing the same real and simulated data sets. Performance was judged by the distributions of image intensities for source and no-source vehicles over many trials as a function of source strength. We found that MVIR produced significantly better results in all cases. The performance difference was greatest at low count rates, where source/no-source distributions were well separated with the MVIR method, allowing reliable source vehicle identification with a low probability of false positive identifications. Static reconstruction of the same data produced overlapping distributions that made source vehicle identification unreliable. The performance of the static method was acceptable at high count rates. Both algorithms reliably identified two strong sources passing through at nearly the same time.

  4. Prototyping the Future

    Science.gov (United States)

    1998-01-01

    Advanced Ceramics Research (ACR) of Tucson, Arizona, researches transforming scientific concepts into technological achievement. Through the SBIR (Small Business Innovative Research) program, ACR developed a high pressure and temperature fused deposition system, a prototyping system that is known as extrusion freeform fabrication. This system is useful in manufacturing prosthetics. ACR also developed a three-dimensional rapid prototyping process in which physical models are quickly created directly from computer generated models. Marshall Space Flight Center also contracted ACR to fabricate a set of ceramic engines to be appraised for a solar thermal rocket engine test program.

  5. A rapid, small-scale sedimentation method to predict breadmaking quality of hard winter wheat

    Science.gov (United States)

    Breeders and processors are always looking for rapid and accurate methods to evaluate wheat quality. A rapid small-scale hybrid sedimentation method was developed for predicting breadmaking quality of breeders samples by combining the sodium dodecyl-sulfate (SDS) sedimentation method (AACC 56-70) an...

  6. A rapid method to estimate Westergren sedimentation rates

    Science.gov (United States)

    Alexy, Tamas; Pais, Eszter; Meiselman, Herbert J.

    2009-01-01

    The erythrocyte sedimentation rate (ESR) is a nonspecific but simple and inexpensive test that was introduced into medical practice in 1897. Although it is commonly utilized in the diagnosis and follow-up of various clinical conditions, ESR has several limitations including the required 60 min settling time for the test. Herein we introduce a novel use for a commercially available computerized tube viscometer that allows the accurate prediction of human Westergren ESR rates in as little as 4 min. Owing to an initial pressure gradient, blood moves between two vertical tubes through a horizontal small-bore tube and the top of the red blood cell (RBC) column in each vertical tube is monitored continuously with an accuracy of 0.083 mm. Using data from the final minute of a blood viscosity measurement, a sedimentation index (SI) was calculated and correlated with results from the conventional Westergren ESR test. To date, samples from 119 human subjects have been studied and our results indicate a strong correlation between SI and ESR values (R2=0.92). In addition, we found a close association between SI and RBC aggregation indices as determined by an automated RBC aggregometer (R2=0.71). Determining SI on human blood is rapid, requires no special training and has minimal biohazard risk, thus allowing physicians to rapidly screen for individuals with elevated ESR and to monitor therapeutic responses. PMID:19791973

  7. Comparison of rapid colorimetric method with conventional method in the isolation of mycobacterium tuberculosis

    Directory of Open Access Journals (Sweden)

    Oberoi A

    2004-01-01

    Full Text Available The aim of the study was to evaluate two methods (colorimetric and conventional for isolation of Mycobacterium tuberculosis. A total of 500 clinical specimens were processed by modified Petroff′s method and then inoculated into MB/BacT-240 system bottles and on LJ medium slopes. The specimens included 242 sputum, 95 gastric aspirates, 47 pleural fluids, 45 CSF, 32 urine, 18 pus, 11 bronchoalveolar lavage, 3 tissue, 2 stool, 2 lymphnode specimens, 2 synovial fluid and 1 bronchial wash specimens. The isolation rate was 16.4% by the colorimetric method and 2.2% by the conventional method. The mean detection time was 16 days and 26 days respectively. Among 36 direct smear positive samples, 63.9%(23/36 and 30%(11/36 were positive by colorimetric and conventional methods respectively. Out of 464 direct smear negative samples 12.9%(60/464 and 0.6%(3/464 were positive by colorimetric and conventional methods respectively. Therefore, colorimetric method enables rapid detection leading to early diagnosis and drug susceptibility testing.

  8. Rapid and Reliable HPLC Method for the Determination of Vitamin ...

    African Journals Online (AJOL)

    Purpose: To develop and validate an accurate, sensitive and reproducible high performance liquid chromatographic (HPLC) method for the quantitation of vitamin C in pharmaceutical samples. Method: The drug and the standard were eluted from Superspher RP-18 (250 mm x 4.6 mm, 10ìm particle size) at 20 0C.

  9. Rapid, cost-effective liquid chromatograghic method for the ...

    African Journals Online (AJOL)

    The method is highly sensitive, with limit of detection of 1 ng/ml. The coefficient of variation for within-day run was less than 4% while that of day-to-day run was less than 6%. There were no interfering peaks from endogenous materials in the serum. The method was validated and used for pharmacokinetic studies ...

  10. Method

    Directory of Open Access Journals (Sweden)

    Ling Fiona W.M.

    2017-01-01

    Full Text Available Rapid prototyping of microchannel gain lots of attention from researchers along with the rapid development of microfluidic technology. The conventional methods carried few disadvantages such as high cost, time consuming, required high operating pressure and temperature and involve expertise in operating the equipment. In this work, new method adapting xurography method is introduced to replace the conventional method of fabrication of microchannels. The novelty in this study is replacing the adhesion film with clear plastic film which was used to cut the design of the microchannel as the material is more suitable for fabricating more complex microchannel design. The microchannel was then mold using polymethyldisiloxane (PDMS and bonded with a clean glass to produce a close microchannel. The microchannel produced had a clean edge indicating good master mold was produced using the cutting plotter and the bonding between the PDMS and glass was good where no leakage was observed. The materials used in this method is cheap and the total time consumed is less than 5 hours where this method is suitable for rapid prototyping of microchannel.

  11. A simple and rapid molecular method for Leptospira species identification

    NARCIS (Netherlands)

    Ahmed, Ahmed; Anthony, Richard M.; Hartskeerl, Rudy A.

    2010-01-01

    Serological and DNA-based classification systems only have little correlation. Currently serological and molecular methods for characterizing Leptospira are complex and costly restricting their world-wide distribution and use. Ligation mediated amplification combined with microarray analysis

  12. A method of rapid testing of radioactivity of different materials

    Directory of Open Access Journals (Sweden)

    Yu. Zabulonov

    2016-10-01

    Full Text Available A new method for the detection of low-level ionising radiation in solid, liquid or loose materials, which is based on the use of the Bayesian approach for the estimation of probabilistic parameters and a special statistical criterion, is offered in the present paper. We describe the algorithm and show the advantages of the method. The approach can be effective even in the case of extremely low signals whose intensity is much less than the background radiation.

  13. A rapid cloning method employing orthogonal end protection.

    Directory of Open Access Journals (Sweden)

    Arjen J Jakobi

    Full Text Available We describe a novel in vitro cloning strategy that combines standard tools in molecular biology with a basic protecting group concept to create a versatile framework for the rapid and seamless assembly of modular DNA building blocks into functional open reading frames. Analogous to chemical synthesis strategies, our assembly design yields idempotent composite synthons amenable to iterative and recursive split-and-pool reaction cycles. As an example, we illustrate the simplicity, versatility and efficiency of the approach by constructing an open reading frame composed of tandem arrays of a human fibronectin type III (FNIII domain and the von Willebrand Factor A2 domain (VWFA2, as well as chimeric (FNIII(n-VWFA2-(FNIII(n constructs. Although we primarily designed this strategy to accelerate assembly of repetitive constructs for single-molecule force spectroscopy, we anticipate that this approach is equally applicable to the reconstitution and modification of complex modular sequences including structural and functional analysis of multi-domain proteins, synthetic biology or the modular construction of episomal vectors.

  14. Rapid, specific and sensitive method for isoniazid determination in serum.

    Science.gov (United States)

    Sadeg, N; Pertat, N; Dutertre, H; Dumontet, M

    1996-01-12

    An original simple, specific and rapid high-performance liquid chromatographic assay for the determination of isoniazid (INH) in human serum is presented. The drug was extracted from the serum by protein precipitation with 30% (w/v) trichloroacetic acid, then the drug was reacted with the coupling reagent, trans-cinnamaldehyde, to form a derivative absorbing at 340 nm. A 20-microliters aliquot was injected into the chromatograph after neutralization with 1 M KOH solution. A liquid chromatograph equipped with a reversed-phase 30-microns C18 precolumn linked to a 4-microns C18 analytical column was used. The drug was eluted with a mixture of acetonitrile-water-triethylamine-acetic acid (400:600:2:1, v/v), pH value was 5 +/- 1. Flow-rate and wavelength were set at 1 ml/min and 340 nm, respectively. The extraction recoveries from human serum averaged 100% for INH at concentrations of 1, 2 and 4 mg/l. The coefficients of variation for three different concentrations for INH in serum in the within-day study varied between 1.2 and 3.5%, whereas those in the day-to-day study varied between 2.8 and 4.3%.

  15. Asymptotic and Numerical Methods for Rapidly Rotating Buoyant Flow

    Science.gov (United States)

    Grooms, Ian G.

    This thesis documents three investigations carried out in pursuance of a doctoral degree in applied mathematics at the University of Colorado (Boulder). The first investigation concerns the properties of rotating Rayleigh-Benard convection -- thermal convection in a rotating infinite plane layer between two constant-temperature boundaries. It is noted that in certain parameter regimes convective Taylor columns appear which dominate the dynamics, and a semi-analytical model of these is presented. Investigation of the columns and of various other properties of the flow is ongoing. The second investigation concerns the interactions between planetary-scale and mesoscale dynamics in the oceans. Using multiple-scale asymptotics the possible connections between planetary geostrophic and quasigeostrophic dynamics are investigated, and three different systems of coupled equations are derived. Possible use of these equations in conjunction with the method of superparameterization, and extension of the asymptotic methods to the interactions between mesoscale and submesoscale dynamics is ongoing. The third investigation concerns the linear stability properties of semi-implicit methods for the numerical integration of ordinary differential equations, focusing in particular on the linear stability of IMEX (Implicit-Explicit) methods and exponential integrators applied to systems of ordinary differential equations arising in the numerical solution of spatially discretized nonlinear partial differential equations containing both dispersive and dissipative linear terms. While these investigations may seem unrelated at first glance, some reflection shows that they are in fact closely linked. The investigation of rotating convection makes use of single-space, multiple-time-scale asymptotics to deal with dynamics strongly constrained by rotation. Although the context of thermal convection in an infinite layer seems somewhat removed from large-scale ocean dynamics, the asymptotic

  16. Prototypes in engineering design: Definitions and strategies

    DEFF Research Database (Denmark)

    Jensen, Lasse Skovgaard; Özkil, Ali Gürcan; Mortensen, Niels Henrik

    2016-01-01

    strategies. Due to rapid changes and progressions in the use of prototypes, we conclude conclude that there is a need for more holistic and overview generating research about prototyping. This for product developers to properly manage, select and apply the optimal prototyping process....

  17. Fiscal 1997 report on the results of the international standardization R and D. Data format for rapid prototyping systems; 1997 nendo seika hokokusho kokusai hyojun soseigata kenkyu kaihatsu. Sekiso zokei system yo data format

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Concerning the rapid prototyping (RP) system use new RP format and the related software, the paper promoted the international standardization in consideration of relationships with an international standard, STEP. RP, which is a technology to rapidly prototype a solid body based on the three-dimensional CAD data, is used in various fields of product manufacture, medical field, etc., and is expected to further expand its field of application. In this R and D, an international version of the RP software system developed for domestic use was developed, and at the same time a software was trially manufactured so that the data on STEP/AP203/CC5 and CC6 can be delivered to the system. Moreover, a plan on new AIC51X as the STEP/AIC suitable for PR was studied. Relating to these results, the paper conducted the publicity work to the persons concerned in RP in the U.S. and Europe, and also explained those at ISO/TC184/SC4 (STEP Conference). The PR use interface enabling highly rapid and accurate data processing reached to a stage of the international commercialization, and at the same time the study items were materialized for proposal of the new STEP standards suitable for RP. 18 refs., 80 figs., 12 tabs.

  18. The Strategic Fitness Process: A Collaborative Action Research Method for Developing and Understanding Organizational Prototypes and Dynamic Capabilities

    Directory of Open Access Journals (Sweden)

    Michael Beer

    2013-04-01

    Full Text Available Organizations underperform and sometimes fail because their leaders are unable to learn the unvarnished truth from relevant stakeholders about how the design and behavior of the organization is misaligned with its goals and strategy. The Strategic Fitness Process (SFP was designed to enable leaders to overcome organizational silence about the misalignment with the environment and chosen strategy. By enabling an honest, organization-wide and public conversation, senior management teams, working collaboratively with scholar-consultants and organizational members, have access to valid data (the unvarnished truth, can conduct a valid diagnosis, and can develop a valid plan to change the structure, processes, and behavior of an organization while at the same time developing commitment that ensures execution. SFP is also a research method. By applying SFP iteratively to new and challenging situations, scholar-consultants can invent new organizational prototypes as well as learn if a standardized and institutionalized organizational learning process like SFP can enhance dynamic capabilities. The SFP model is illustrated with an application to Hewlett-Packard’s Santa Rosa Systems Division.

  19. Greenbrier Prototype

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-06-18

    This case study describes a prototype home that is the model home for the Homes at Greenbrier in Oakdale, Connecticut, and demonstrates the builder's concept of “attainable sustainable” of offering high performance homes at mid-market prices.

  20. Rapid, cost-effective liquid chromatograghic method for the ...

    African Journals Online (AJOL)

    GRACE

    2006-07-03

    Jul 3, 2006 ... Akay C, Ozkan SA, Senturk Z, Cevheroglu S (2002). Simultaneous determination of metronidazole and miconazole in pharmaceutical dosage form by HPLC. Farmaco. Nov.57(11): 953-7. Galmier MJ, Frasey AM, Bastide M, Beyssac E, Petit J, Aiache JM,. Lartigue-Mattei (1998). Simple and sensitive method ...

  1. RESEARCH NOTE A Universal, rapid, and inexpensive method for ...

    Indian Academy of Sciences (India)

    Navya

    very satisfactory for many researchers to prepare reagents for “all in one” ready to use method to extract gDNA from very wide range sources of blood samples. To meet these criteria, a universal and versatile DNA extraction procedure should be developedwith a minimal chemicals and equipment.On the other hand, the ...

  2. [Methods for the rapid preparation of paraffin blocks].

    Science.gov (United States)

    Shmurun, R I

    1992-01-01

    Two accelerated chloroform-paraffin processings of materials with the use of ultrasound (US) and microwave (MW) irradiation in the stove "Electronica" as well as a combined method with US- and MW-irradiation are proposed to shorten drastically the duration of the prehistologic processing.

  3. Rapid multi-residue method for the determination of pesticide ...

    African Journals Online (AJOL)

    Exposure to pesticides can represent a potential risk to humans. Agricultural workers are at risk of chronic toxicity. Hence, the evaluation of pesticide residues in their blood gives an indication about the extent of exposure and help in assessing adverse health effects. The aim of our study was to develop analytical method for ...

  4. Time evolution of the wave equation using rapid expansion method

    KAUST Repository

    Pestana, Reynam C.

    2010-07-01

    Forward modeling of seismic data and reverse time migration are based on the time evolution of wavefields. For the case of spatially varying velocity, we have worked on two approaches to evaluate the time evolution of seismic wavefields. An exact solution for the constant-velocity acoustic wave equation can be used to simulate the pressure response at any time. For a spatially varying velocity, a one-step method can be developed where no intermediate time responses are required. Using this approach, we have solved for the pressure response at intermediate times and have developed a recursive solution. The solution has a very high degree of accuracy and can be reduced to various finite-difference time-derivative methods, depending on the approximations used. Although the two approaches are closely related, each has advantages, depending on the problem being solved. © 2010 Society of Exploration Geophysicists.

  5. A taxonomy of rapid reviews links report types and methods to specific decision-making contexts.

    Science.gov (United States)

    Hartling, Lisa; Guise, Jeanne-Marie; Kato, Elisabeth; Anderson, Johanna; Belinson, Suzanne; Berliner, Elise; Dryden, Donna M; Featherstone, Robin; Mitchell, Matthew D; Motu'apuaka, Makalapua; Noorani, Hussein; Paynter, Robin; Robinson, Karen A; Schoelles, Karen; Umscheid, Craig A; Whitlock, Evelyn

    2015-12-01

    Describe characteristics of rapid reviews and examine the impact of methodological variations on their reliability and validity. We conducted a literature review and interviews with organizations that produce rapid reviews or related products to identify methods, guidance, empiric evidence, and current practices. We identified 36 rapid products from 20 organizations (production time, 5 minutes to 8 months). Methods differed from systematic reviews at all stages. As time frames increased, methods became more rigorous; however, restrictions on database searching, inclusion criteria, data extracted, and independent dual review remained. We categorized rapid products based on extent of synthesis. "Inventories" list what evidence is available. "Rapid responses" present best available evidence with no formal synthesis. "Rapid reviews" synthesize the quality of and findings from the evidence. "Automated approaches" generate meta-analyses in response to user-defined queries. Rapid products rely on a close relationship with end users and support specific decisions in an identified time frame. Limited empiric evidence exists comparing rapid and systematic reviews. Rapid products have tremendous methodological variation; categorization based on time frame or type of synthesis reveals patterns. The similarity across rapid products lies in the close relationship with the end user to meet time-sensitive decision-making needs. Copyright © 2015 Elsevier Inc. All rights reserved.

  6. Systems and methods for rapid processing and storage of data

    Science.gov (United States)

    Stalzer, Mark A.

    2017-01-24

    Systems and methods of building massively parallel computing systems using low power computing complexes in accordance with embodiments of the invention are disclosed. A massively parallel computing system in accordance with one embodiment of the invention includes at least one Solid State Blade configured to communicate via a high performance network fabric. In addition, each Solid State Blade includes a processor configured to communicate with a plurality of low power computing complexes interconnected by a router, and each low power computing complex includes at least one general processing core, an accelerator, an I/O interface, and cache memory and is configured to communicate with non-volatile solid state memory.

  7. Rapid new methods for paint collection and lead extraction.

    Science.gov (United States)

    Gutknecht, William F; Harper, Sharon L; Winstead, Wayne; Sorrell, Kristen; Binstock, David A; Salmons, Cynthia A; Haas, Curtis; McCombs, Michelle; Studabaker, William; Wall, Constance V; Moore, Curtis

    2009-01-01

    Chronic exposure of children to lead can result in permanent physiological impairment. In adults, it can cause irritability, poor muscle coordination, and nerve damage to the sense organs and nerves controlling the body. Surfaces coated with lead-containing paints are potential sources of exposure to lead. In April 2008, the U.S. Environmental Protection Agency (EPA) finalized new requirements that would reduce exposure to lead hazards created by renovation, repair, and painting activities, which disturb lead-based paint. On-site, inexpensive identification of lead-based paint is required. Two steps have been taken to meet this challenge. First, this paper presents a new, highly efficient method for paint collection that is based on the use of a modified wood drill bit. Second, this paper presents a novel, one-step approach for quantitatively grinding and extracting lead from paint samples for subsequent lead determination. This latter method is based on the use of a high-revolutions per minute rotor with stator to break up the paint into approximately 50 micron-size particles. Nitric acid (25%, v/v) is used to extract the lead in 95% for real-world paints, National Institute of Standards and Technology's standard reference materials, and audit samples from the American Industrial Hygiene Association's Environmental Lead Proficiency Analytical Testing Program. This quantitative extraction procedure, when paired with quantitative paint sample collection and lead determination, may enable the development of a lead paint test kit that will meet the specifications of the final EPA rule.

  8. Susceptibility testing of filamentous fungi to amphotericin B by a rapid radiometric method

    Energy Technology Data Exchange (ETDEWEB)

    Merz, W.G.; Fay, D.; Thumar, B.; Dixon, D.

    1984-01-01

    A rapid, radiometric method was developed to determine the susceptibility of filamentous fungi to amphotericin B. The rapid, radiometric method depended on measurement of the inhibition of /sup 24/CO/sub 2/ production in the presence of amphotericin B. Thirty isolates of filamentous fungi were tested by the rapid, radiometric method and a reference agar dilution method. There was 93% agreement between the two methods when an 80% or greater decrease in CO/sub 2/ production was used to calculate the minimal inhibitory concentration with the rapid, radiometric method. Minimal inhibitory concentrations, based on 80% decrease of CO/sub 2/ production, were achieved within 24 h of incubation with all of the fungi tested.

  9. Microwave as a rapid cooking method for beef tenderness evaluation.

    Science.gov (United States)

    Silva, Douglas R G; Fernandez, Ludimila C; Torres Filho, Robledo A; Fontes, Paulo R; Ramos, Alcinéia L S; Ramos, Eduardo M

    2017-11-20

    Semitendinosus (ST) muscle steaks were grouped according to three locations (proximal, middle, and distal end), grilled to endpoint temperature of 71C or cooked for 20, 30, 40, 50, or 60 s in a microwave oven (Mw). The location did not affect (p > .05) the cooking loss (CL) or shear force (SF) values. The CL increased (p  .05) from the grill samples. None of the microwaves' SF values were different (p > .05) from the grill values, with treatments Mw30 to Mw50 showing moderate repeatability (R = 0.51-0.60) and Mw30 and Mw60 showing higher correlations (r > .71) with grill values. Cooking beef strips with a microwave is a potential method for tenderness evaluation, but requires additional study to evaluate and optimize this application in different muscles and for comparison to sensorial data. The work was intended to evaluate the possibility of using a microwave oven for cooking meat to be used in objective measurement protocols for meat tenderness and to optimize the conditions for this purpose. The use of a standardized microwave procedure allows a dramatic reduction in analysis time and may reduce error variance due to nonuniform cooking procedures. © 2017 Wiley Periodicals, Inc.

  10. A method for rapid abundance estimation of semiplanktonic meiofauna

    Science.gov (United States)

    Armonies, Werner

    2000-12-01

    Many meiofaunal copepods and plathelminths enter the tidal waters at night thus exhibiting a life-style intermediate between benthic and planktonic. At the same time, ostracods may leave their interstitial dwelling and move across the sediment surface. In laboratory experiments, the percentage of plathelminth populations emerging from the sediment varied with the species, temperature, light conditions, and the dimensions of the sediment cores studied, but not with tidal level, season, ambient density of conspecifics, or the sediment composition. Therefore, the swimming activity may be utilised for extraction of semiplanktonic meiofauna provided that the extraction procedure is standardised with respect to temperature, light and core size. For free-living plathelminths from the Wadden Sea intertidal a robust standard procedure is as follows: sediment cores 1.6 cm in diameter (2 cm2 surface area) and 3 cm deep are fitted into cylindrical containers and submerged into aquaria containing filtered seawater (ambient salinity, room temperature, darkness) for 24 h. The sediment containers are then removed and the aquarian water filtered through appropriate meshes; the residue contains the emergent faunal component. For plathelminths, this procedure reduces sorting time by some 90% compared with the standard shaking-decantation method and thus makes it possible to process a high number of samples in a short time. Similar procedures may be developed for copepods and epibenthic ostracods.

  11. A Classification and Bibliography of Software Prototyping.

    Science.gov (United States)

    1992-10-01

    Integrating the Role of Rapid Prototyping and Requirements Specification Using the Object-oriented Paradigm Author: Heisler , K.G.; Tsai, W.T. Source...specification, structured analysis Abstract: A methodology for rapid prototyping is described. Modified data flow diagrams are used as a graphical tool and...problem. The graphical editor under development for the computer aided prototyping system (CAPS) proposes a dataflow- diagram -based model with multiple

  12. Rapid methods for the detection of foodborne bacterial pathogens: principles, applications, advantages and limitations

    Science.gov (United States)

    Law, Jodi Woan-Fei; Ab Mutalib, Nurul-Syakima; Chan, Kok-Gan; Lee, Learn-Han

    2015-01-01

    The incidence of foodborne diseases has increased over the years and resulted in major public health problem globally. Foodborne pathogens can be found in various foods and it is important to detect foodborne pathogens to provide safe food supply and to prevent foodborne diseases. The conventional methods used to detect foodborne pathogen are time consuming and laborious. Hence, a variety of methods have been developed for rapid detection of foodborne pathogens as it is required in many food analyses. Rapid detection methods can be categorized into nucleic acid-based, biosensor-based and immunological-based methods. This review emphasizes on the principles and application of recent rapid methods for the detection of foodborne bacterial pathogens. Detection methods included are simple polymerase chain reaction (PCR), multiplex PCR, real-time PCR, nucleic acid sequence-based amplification (NASBA), loop-mediated isothermal amplification (LAMP) and oligonucleotide DNA microarray which classified as nucleic acid-based methods; optical, electrochemical and mass-based biosensors which classified as biosensor-based methods; enzyme-linked immunosorbent assay (ELISA) and lateral flow immunoassay which classified as immunological-based methods. In general, rapid detection methods are generally time-efficient, sensitive, specific and labor-saving. The developments of rapid detection methods are vital in prevention and treatment of foodborne diseases. PMID:25628612

  13. Rapid Methods for the Detection of Foodborne Bacterial Pathogens: Principles, Applications, Advantages and Limitations

    Directory of Open Access Journals (Sweden)

    Law eJodi Woan-Fei

    2015-01-01

    Full Text Available The incidence of foodborne diseases has increased over the years and resulted in major public health problem globally. Foodborne pathogens can be found in various foods and it is important to detect foodborne pathogens to provide safe food supply and to prevent foodborne diseases. The conventional methods used to detect foodborne pathogen are time consuming and laborious. Hence, a variety of methods have been developed for rapid detection of foodborne pathogens as it is required in many food analyses. Rapid detection methods can be categorized into nucleic acid-based, biosensor-based and immunological-based methods. This review emphasizes on the principles and application of recent rapid methods for the detection of foodborne bacterial pathogens. Detection methods included are simple polymerase chain reaction (PCR, multiplex PCR, real-time PCR, nucleic acid sequence-based amplification (NASBA, loop-mediated isothermal amplification (LAMP and oligonucleotide DNA microarray which classified as nucleic acid-based methods; optical, electrochemical and mass-based biosensors which classified as biosensor-based methods; enzyme-linked immunosorbent assay (ELISA and lateral flow immunoassay which classified as immunological-based methods. In general, rapid detection methods are generally time-efficient, sensitive, specific and labor-saving. The developments of rapid detection methods are vital in prevention and treatment of foodborne diseases.

  14. Methods and Magnitudes of Rapid Weight Loss in Judo Athletes Over Pre-Competition Periods

    Directory of Open Access Journals (Sweden)

    Kons Rafael Lima

    2017-06-01

    Full Text Available Purpose. The study aimed to analyse the methods and magnitudes of rapid weight loss (RWL in judo team members in distinct periods before the biggest state competition in Southern Brazil.

  15. Rapid identification of salmonella serotypes with stereo and hyperspectral microscope imaging Methods

    Science.gov (United States)

    The hyperspectral microscope imaging (HMI) method can reduce detection time within 8 hours including incubation process. The early and rapid detection with this method in conjunction with the high throughput capabilities makes HMI method a prime candidate for implementation for the food industry. Th...

  16. A development of maintenance educational support method by using navigation method. Pt. 2. A basic design of RHR pump maintenance educational support prototype system

    Energy Technology Data Exchange (ETDEWEB)

    Yoshino, Kenji; Hirotsu, Yuko; Fujimoto, Junzo [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

    2002-04-01

    The nuclear power plant has the human error produced from the disagreement of the difficulty of systematic error and maintenance work and the work execution capability, such as the persons concerned, which are produced from the fault of the command and the chain of command concerning organization. Then, this research establishes the new maintenance educational support prototype system for aiming at organization as Trinity (a supervision person, a construction person in charge, a work person in charge, and group length) , and improvement in human reliability for the purpose of aiming at before hand prevention of a systematic error, human error, and the accident and a trouble. Main results (I) In this research, as a result of investigating and analyzing about an exchange of the information which exists between the Trinity of concerning maintenance work execution, it became clear that the command and the chain of command for job execution exist among 3 persons. (Fig. 1) It will consider as the index for establishment of this command and chain of command of the maintenance educational support method from now on. (2) The basic design was performed on the educator's-ed position-and-rank level' about the 'prototype system' which enables suitable educational support. (Fig. 2) Its feature are as follows. (I) Presumption of the mismatch portion concerning the position-and-rank level / work execution capability before and behind the education by the initial educational scenario concerning an organization / on-site work, and education, (2) Implementation of reeducation by the 'reeducation scenario' concerning the organization / on-site work for complementing and canceling the mismatch portion. (3) Implementation of the comprehensive judgment (the educational effect) by analysis of the contents of a reply (conversation) of the educator-ed in reeducation scenario process. By this research, the possibility of the self-recognition of the problem of

  17. Assessment of three rapid methods for the detection of methicillin-resistant Staphylococcus aureus.

    Science.gov (United States)

    Soares, Maria João; Soares, Carlos; Mendes, Ana Constança; Guimarães, Maria Luís; Cabeda, José Manuel; Amorim, José Manuel

    2004-01-01

    We evaluated three rapid methods to detect methicillin-resistant Staphylococcus aureus (MRSA) and compared them with PCR amplification of mecA. A total of 103 S. aureus strains were studied by MRSA-Screen, BBL Crystal, Velogene Genomic and mecA PCR. All the methods detected the 61 MRSA strains having the mecA gene, showing 100% sensitivity and specificity. Despite the correlation between all the rapid methods and PCR, the ease of use and shorter turnaround time of MRSA-Screen were important factors leading to the selection of this method as the routine screening technique for MRSA.

  18. Can MODIS data calibrate and validate coastal sediment transport models? Rapid prototyping using 250 m data and the ECOMSED model for Lake Pontchartrain, LA USA.

    Science.gov (United States)

    Miller, R. L.; Glorioso, M. V.; Georgiou, I.; McCorquodale, J. A.; Crower, K.

    2006-12-01

    Field measurements from small boats and sparse arrays of instrumented buoys often do not provide sufficient data to capture the dynamic nature of bio-geophysical parameters in many coastal aquatic environments. Several investigators have shown that MODIS 250 m images can provide daily synoptic views of suspended sediment concentration in coastal waters to determine sediment transport and fate. However, the use of MODIS for coastal environments can be limited due to a lack of cloud-free images. Sediment transport models are not constrained by sky conditions but often suffer from a lack of in situ observations for model calibration or validation. We will demonstrate the utility of MODIS 250 m to calibrate (set model parameters), validate output, and set or re-set initial conditions of a hydrodynamic and sediment transport model (ECOMSED) developed for Lake Pontchartrain, LA USA. We will present our approach to quickly assess or `prototype' the application of NASA data to support environmental managers and decision makers. The combination of daily MODIS imagery and model simulations offer a more robust monitoring and prediction system of suspended sediments than available from either system alone. We will also present a brief introduction of how this approach will be implemented to assess the future use of NPOES-VIIRS images for monitoring coastal sediment processes.

  19. The Application of Rapid Prototyping Technology and Quality Functional Deployment (QFD approach in enhancing the Endotracheal Tube Holder Model in Medical Application

    Directory of Open Access Journals (Sweden)

    Way Yusoff

    2015-01-01

    Full Text Available This paper presents a development of a current design the Endotracheal tube holding device. At present, the medical teams have faced a lot of problems when doing the endotracheal intubation. Misplacement of endotracheal tube into the esophagus and extubation due to patient’s movement are among the problems by surgeons during medical treatment. This is important as the successful management of the potential risk can reduce the number of patients who suffer a serious consequence of endtracheal tube therapy such as a potential risk to patient safety, with associated risks varying from minor complications to death. This paper presents a product design specification for endotracheal tube-holding device is translated from user’s requirements by employing Quality Functional Deployment (QFD. Several design concepts are generated by using CATIA software to be evaluated by endotracheal tube-holding device users for concept selection. Selection of design concept was done in two phases which are concept screening and concept scoring. For selecting the design concept for further development, a prototype of endotracheal tube was fabricated by using Fused Deposition Modelling (FDM.

  20. Development of a Decision Aid for Cardiopulmonary Resuscitation Involving Intensive Care Unit Patients' and Health Professionals' Participation Using User-Centered Design and a Wiki Platform for Rapid Prototyping: A Research Protocol.

    Science.gov (United States)

    Plaisance, Ariane; Witteman, Holly O; Heyland, Daren Keith; Ebell, Mark H; Dupuis, Audrey; Lavoie-Bérard, Carole-Anne; Légaré, France; Archambault, Patrick Michel

    2016-02-11

    Cardiopulmonary resuscitation (CPR) is an intervention used in cases of cardiac arrest to revive patients whose heart has stopped. Because cardiac arrest can have potentially devastating outcomes such as severe neurological deficits even if CPR is performed, patients must be involved in determining in advance if they want CPR in the case of an unexpected arrest. Shared decision making (SDM) facilitates discussions about goals of care regarding CPR in intensive care units (ICUs). Patient decision aids (DAs) are proven to support the implementation of SDM. Many patient DAs about CPR exist, but they are not universally implemented in ICUs in part due to lack of context and cultural adaptation. Adaptation to local context is an important phase of implementing any type of knowledge tool such as patient DAs. User-centered design supported by a wiki platform to perform rapid prototyping has previously been successful in creating knowledge tools adapted to the needs of patients and health professionals (eg, asthma action plans). This project aims to explore how user-centered design and a wiki platform can support the adaptation of an existing DA for CPR to the local context. The primary objective is to use an existing DA about CPR to create a wiki-based DA that is adapted to the context of a single ICU and tailorable to individual patient's risk factors while employing user-centered design. The secondary objective is to document the use of a wiki platform for the adaptation of patient DAs. This study will be conducted in a mixed surgical and medical ICU at Hôtel-Dieu de Lévis, Quebec, Canada. We plan to involve all 5 intensivists and recruit at least 20 alert and oriented patients admitted to the ICU and their family members if available. In the first phase of this study, we will observe 3 weeks of daily interactions between patients, families, intensivists, and other allied health professionals. We will specifically observe 5 dyads of attending intensivists and alert

  1. Development and Evaluation of the Virtual Prototype of the First Saudi Arabian-Designed Car

    Directory of Open Access Journals (Sweden)

    Mustufa H. Abidi

    2016-10-01

    Full Text Available Prototyping and evaluation are imperative phases of the present product design and development process. Although digital modeling and analysis methods are widely employed at various product development stages, still, building a physical prototype makes the present typical process expensive and time consuming. Therefore, it is necessary to implement new technologies, such as virtual prototyping, which can enable industry to have a rapid and more controlled decision making process. Virtual prototyping has come a long way in recent years, where current environments enable stereoscopic visuals, surround sound and ample interaction with the generated models. It is also important to evaluate how representative the developed virtual prototype is when compared to the real-world counterpart and the sense of presence reported by users of the virtual prototype. This paper describes the systematic procedure to develop a virtual prototype of Gazal-1 (i.e., the first car prototype designed by Saudi engineers in a semi-immersive virtual environment. The steps to develop a virtual prototype from CAD (computer-aided design models are explained in detail. Various issues involved in the different phases for the development of the virtual prototype are also discussed comprehensively. The paper further describes the results of the subjective assessment of a developed virtual prototype of a Saudi Arabian-designed automobile. User’s feedback is recorded using a presence questionnaire. Based on the user-based study, it is revealed that the virtual prototype is representative of the real Saudi Arabian car and offers a flexible environment to analyze design features when compared against its physical prototype. The capabilities of the virtual environment are validated with the application of the car prototype. Finally, vital requirements and directions for future research are also presented.

  2. Virtual prototype and experimental research on gear multi-fault diagnosis using wavelet-autoregressive model and principal component analysis method

    Science.gov (United States)

    Li, Zhixiong; Yan, Xinping; Yuan, Chengqing; Peng, Zhongxiao; Li, Li

    2011-10-01

    Gear systems are an essential element widely used in a variety of industrial applications. Since approximately 80% of the breakdowns in transmission machinery are caused by gear failure, the efficiency of early fault detection and accurate fault diagnosis are therefore critical to normal machinery operations. Reviewed literature indicates that only limited research has considered the gear multi-fault diagnosis, especially for single, coupled distributed and localized faults. Through virtual prototype simulation analysis and experimental study, a novel method for gear multi-fault diagnosis has been presented in this paper. This new method was developed based on the integration of Wavelet transform (WT) technique, Autoregressive (AR) model and Principal Component Analysis (PCA) for fault detection. The WT method was used in the study as the de-noising technique for processing raw vibration signals. Compared with the noise removing method based on the time synchronous average (TSA), the WT technique can be performed directly on the raw vibration signals without the need to calculate any ensemble average of the tested gear vibration signals. More importantly, the WT can deal with coupled faults of a gear pair in one operation while the TSA must be carried out several times for multiple fault detection. The analysis results of the virtual prototype simulation prove that the proposed method is a more time efficient and effective way to detect coupled fault than TSA, and the fault classification rate is superior to the TSA based approaches. In the experimental tests, the proposed method was compared with the Mahalanobis distance approach. However, the latter turns out to be inefficient for the gear multi-fault diagnosis. Its defect detection rate is below 60%, which is much less than that of the proposed method. Furthermore, the ability of the AR model to cope with localized as well as distributed gear faults is verified by both the virtual prototype simulation and

  3. Evaluation of two methods of rapid blood-glucose monitoring by unskilled personnel during surgery

    DEFF Research Database (Denmark)

    Madsbad, S; Adelhøj, B; Bigler, Dennis Richard

    1984-01-01

    The accuracy of two rapid methods of blood-glucose monitoring without (Haemo-glucotest 1-44) and with a reflectance meter (Hypocount B) was compared using a laboratory method. The assessment was carried out by personnel with no previous experience in measuring blood glucose. Eighty-five percent o...

  4. A rapid and convenient method for preparing salt-free (. gamma. -/sup 32/P)ATP

    Energy Technology Data Exchange (ETDEWEB)

    Palmer, J.L.; Avruch, J.

    1981-09-15

    (..gamma..-/sup 32/P)ATP is prepared by an existing enzymatic method that yields approximately 95% incorporation of /sup 32/P into ATP. A rapid and convenient method for purifying the (..gamma..-/sup 32/P)ATP which results in a product free of both salt and buffer is reported.

  5. High performance liquid chromatography method for rapid and accurate determination of homocysteine in plasma and serum

    DEFF Research Database (Denmark)

    Vester, Birte; Rasmussen, K

    1991-01-01

    Determination of homocysteine in plasma or serum for evaluation of cobalamin and folate deficiency is becoming an important diagnostic procedure. Accurate, rapid and low cost methods for measuring homocysteine are therefore required. We have improved an HPLC method and made it suitable for clinical...

  6. Development of a decision aid for cardiopulmonary resuscitation and invasive mechanical ventilation in the intensive care unit employing user-centered design and a wiki platform for rapid prototyping.

    Science.gov (United States)

    Plaisance, Ariane; Witteman, Holly O; LeBlanc, Annie; Kryworuchko, Jennifer; Heyland, Daren Keith; Ebell, Mark H; Blair, Louisa; Tapp, Diane; Dupuis, Audrey; Lavoie-Bérard, Carole-Anne; McGinn, Carrie Anna; Légaré, France; Archambault, Patrick Michel

    2018-01-01

    Upon admission to an intensive care unit (ICU), all patients should discuss their goals of care and express their wishes concerning life-sustaining interventions (e.g., cardiopulmonary resuscitation (CPR)). Without such discussions, interventions that prolong life at the cost of decreasing its quality may be used without appropriate guidance from patients. To adapt an existing decision aid about CPR to create a wiki-based decision aid individually adapted to each patient's risk factors; and to document the use of a wiki platform for this purpose. We conducted three weeks of ethnographic observation in our ICU to observe intensivists and patients discussing goals of care and to identify their needs regarding decision making. We interviewed intensivists individually. Then we conducted three rounds of rapid prototyping involving 15 patients and 11 health professionals. We recorded and analyzed all discussions, interviews and comments, and collected sociodemographic data. Using a wiki, a website that allows multiple users to contribute or edit content, we adapted the decision aid accordingly and added the Good Outcome Following Attempted Resuscitation (GO-FAR) prediction rule calculator. We added discussion of invasive mechanical ventilation. The final decision aid comprises values clarification, risks and benefits of CPR and invasive mechanical ventilation, statistics about CPR, and a synthesis section. We added the GO-FAR prediction calculator as an online adjunct to the decision aid. Although three rounds of rapid prototyping simplified the information in the decision aid, 60% (n = 3/5) of the patients involved in the last cycle still did not understand its purpose. Wikis and user-centered design can be used to adapt decision aids to users' needs and local contexts. Our wiki platform allows other centers to adapt our tools, reducing duplication and accelerating scale-up. Physicians need training in shared decision making skills about goals of care and in using the

  7. A rapid method to determine sterol, erythrodiol, and uvaol concentrations in olive oil.

    Science.gov (United States)

    Mathison, Brian; Holstege, Dirk

    2013-05-15

    A rapid, accurate, and efficient method for determining the sterol, uvaol, and erythrodiol concentrations was developed to meet International Olive Council (IOC) certification criteria for extra virgin olive oil (EVOO). The unsaponifiable fraction of the sample (0.2 g) was separated with a diatomaceous earth column, and the sterol and triterpenic dialcohols were isolated with a novel base-activated silica solid-phase extraction (SPE) cartridge cleanup protocol. The improved method and the IOC method provided identical pass/fail results (n = 34) for each of the six sterol and erythrodiol/uvaol IOC criteria used to assess olive oil. This method was validated, and recoveries of stigmasterol (88%) and β-sitosterol (84%) were greater than previously published values obtained using the IOC method. This method requires approximately one-third the time required to complete the IOC method and has great utility for the rapid screening of EVOO to detect adulteration, false labeling, and an inferior product.

  8. Commercially Available Rapid Methods for Detection of Selected Food-borne Pathogens.

    Science.gov (United States)

    Valderrama, Wladir B; Dudley, Edward G; Doores, Stephanie; Cutter, Catherine N

    2016-07-03

    Generally, the enumeration and isolation of food-borne pathogens is performed using culture-dependent methods. These methods are sensitive, inexpensive, and provide both qualitative and quantitative assessment of the microorganisms present in a sample, but these are time-consuming. For this reason, researchers are developing new techniques that allow detection of food pathogens in shorter period of time. This review identifies commercially available methods for rapid detection and quantification of Listeria monocytogenes, Salmonella spp., Staphylococcus aureus, and Shiga toxin-producing Escherichia coli in food samples. Three categories are discussed: immunologically based methods, nucleic acid-based assays, and biosensors. This review describes the basic mechanism and capabilities of each method, discusses the difficulties of choosing the most convenient method, and provides an overview of the future challenges for the technology for rapid detection of microorganisms.

  9. MITRE sensor layer prototype

    Science.gov (United States)

    Duff, Francis; McGarry, Donald; Zasada, David; Foote, Scott

    2009-05-01

    The MITRE Sensor Layer Prototype is an initial design effort to enable every sensor to help create new capabilities through collaborative data sharing. By making both upstream (raw) and downstream (processed) sensor data visible, users can access the specific level, type, and quantities of data needed to create new data products that were never anticipated by the original designers of the individual sensors. The major characteristic that sets sensor data services apart from typical enterprise services is the volume (on the order of multiple terabytes) of raw data that can be generated by most sensors. Traditional tightly coupled processing approaches extract pre-determined information from the incoming raw sensor data, format it, and send it to predetermined users. The community is rapidly reaching the conclusion that tightly coupled sensor processing loses too much potentially critical information.1 Hence upstream (raw and partially processed) data must be extracted, rapidly archived, and advertised to the enterprise for unanticipated uses. The authors believe layered sensing net-centric integration can be achieved through a standardize-encapsulate-syndicateaggregate- manipulate-process paradigm. The Sensor Layer Prototype's technical approach focuses on implementing this proof of concept framework to make sensor data visible, accessible and useful to the enterprise. To achieve this, a "raw" data tap between physical transducers associated with sensor arrays and the embedded sensor signal processing hardware and software has been exploited. Second, we encapsulate and expose both raw and partially processed data to the enterprise within the context of a service-oriented architecture. Third, we advertise the presence of multiple types, and multiple layers of data through geographic-enabled Really Simple Syndication (GeoRSS) services. These GeoRSS feeds are aggregated, manipulated, and filtered by a feed aggregator. After filtering these feeds to bring just the type

  10. Rapid high temperature field test method for evaluation of geothermal calcite scale inhibitors

    Energy Technology Data Exchange (ETDEWEB)

    Asperger, R.G.

    1982-08-01

    A test method is described which allows the rapid field testing of calcite scale inhibitors in high- temperature geothermal brines. Five commercial formulations, chosen on the basis of laboratory screening tests, were tested in brines with low total dissolved solids at ca 500 F. Four were found to be effective; of these, 2 were found to be capable of removing recently deposited scale. One chemical was tested in the full-flow brine line for 6 wks. It was shown to stop a severe surface scaling problem at the well's control valve, thus proving the viability of the rapid test method. (12 refs.)

  11. Digital Microdroplet Ejection Technology-Based Heterogeneous Objects Prototyping

    Science.gov (United States)

    Yang, Jiquan; Feng, Chunmei; Yang, Jianfei; Zhu, Liya; Guo, Aiqing

    2016-01-01

    An integrate fabrication framework is presented to build heterogeneous objects (HEO) using digital microdroplets injecting technology and rapid prototyping. The heterogeneous materials part design and manufacturing method in structure and material was used to change the traditional process. The net node method was used for digital modeling that can configure multimaterials in time. The relationship of material, color, and jetting nozzle was built. The main important contributions are to combine the structure, material, and visualization in one process and give the digital model for manufacture. From the given model, it is concluded that the method is effective for HEO. Using microdroplet rapid prototyping and the model given in the paper HEO could be gotten basically. The model could be used in 3D biomanufacturing. PMID:26981110

  12. Digital Microdroplet Ejection Technology-Based Heterogeneous Objects Prototyping

    Directory of Open Access Journals (Sweden)

    Na Li

    2016-01-01

    Full Text Available An integrate fabrication framework is presented to build heterogeneous objects (HEO using digital microdroplets injecting technology and rapid prototyping. The heterogeneous materials part design and manufacturing method in structure and material was used to change the traditional process. The net node method was used for digital modeling that can configure multimaterials in time. The relationship of material, color, and jetting nozzle was built. The main important contributions are to combine the structure, material, and visualization in one process and give the digital model for manufacture. From the given model, it is concluded that the method is effective for HEO. Using microdroplet rapid prototyping and the model given in the paper HEO could be gotten basically. The model could be used in 3D biomanufacturing.

  13. A rapid method for soil cement design : Louisiana slope value method.

    Science.gov (United States)

    1964-03-01

    The current procedure used by the Louisiana Department of Highways for laboratory design of cement stabilized soil base and subbase courses is taken from standard AASHO test methods, patterned after Portland Cement Association criteria. These methods...

  14. Furuncular myiasis: a simple and rapid method for extraction of intact Dermatobia hominis larvae.

    Science.gov (United States)

    Boggild, Andrea K; Keystone, Jay S; Kain, Kevin C

    2002-08-01

    We report a case of furuncular myiasis complicated by Staphylococcus aureus infection and beta-hemolytic streptococcal cellulitis. The Dermatobia hominis larva that caused this lesion could not be extracted using standard methods, including suffocation and application of lateral pressure, and surgery was contraindicated because of cellulitis. The botfly maggot was completely and rapidly extracted with an inexpensive, disposable, commercial venom extractor.

  15. Collision-induced fragmentation accurate mass spectrometric analysis methods to rapidly characterize phytochemicals in plant extracts

    Science.gov (United States)

    The rapid advances in analytical chromatography equipment have made the reliable and reproducible measurement of a wide range of plant chemical components possible. Full chemical characterization of a given plant material is possible with the new mass spectrometers currently available. New methods a...

  16. Collaborative validation of a rapid method for efficient virus concentration in bottled water

    DEFF Research Database (Denmark)

    Schultz, Anna Charlotte; Perelle, Sylvie; Di Pasquale, Simona

    2011-01-01

    Enteric viruses, including norovirus (NoV) and hepatitis A virus (HAV), have emerged as a major cause of waterborne outbreaks worldwide. Due to their low infectious doses and low concentrations in water samples, an efficient and rapid virus concentration method is required for routine control. Th...

  17. A Rapid Method for Measuring Strontium-90 Activity in Crops in China

    Directory of Open Access Journals (Sweden)

    Pan Lingjing Pan

    2017-01-01

    Full Text Available A rapid method for measuring Sr-90 activity in crop ashes is presented. Liquid scintillation counting, combined with ion exchange columns 4‘, 4“(5“-di-t-butylcyclohexane-18-crown-6, is used to determine the activity of Sr-90 in crops. The yields of chemical procedure are quantified using gravimetric analysis. The conventional method that uses ion-exchange resin with HDEHP could not completely remove all the bismuth when comparatively large lead and bismuth exist in the samples. This is overcome by the rapid method. The chemical yield of this method is about 60% and the MDA for Sr-90 is found to be 2:32 Bq/kg. The whole procedure together with using spectrum analysis to determine the activity only takes about one day, which is really a large improvement compared with the conventional method. A modified conventional method is also described here to verify the value of the rapid one. These two methods can meet di_erent needs of daily monitoring and emergency situation.

  18. A Rapid Method for Measuring Strontium-90 Activity in Crops in China

    Science.gov (United States)

    Pan, Lingjing Pan; Yu, Guobing; Wen, Deyun; Chen, Zhi; Sheng, Liusi; Liu, Chung-King; Xu, X. George

    2017-09-01

    A rapid method for measuring Sr-90 activity in crop ashes is presented. Liquid scintillation counting, combined with ion exchange columns 4`, 4"(5")-di-t-butylcyclohexane-18-crown-6, is used to determine the activity of Sr-90 in crops. The yields of chemical procedure are quantified using gravimetric analysis. The conventional method that uses ion-exchange resin with HDEHP could not completely remove all the bismuth when comparatively large lead and bismuth exist in the samples. This is overcome by the rapid method. The chemical yield of this method is about 60% and the MDA for Sr-90 is found to be 2:32 Bq/kg. The whole procedure together with using spectrum analysis to determine the activity only takes about one day, which is really a large improvement compared with the conventional method. A modified conventional method is also described here to verify the value of the rapid one. These two methods can meet di_erent needs of daily monitoring and emergency situation.

  19. Considerations for Task Analysis Methods and Rapid E-Learning Development Techniques

    Directory of Open Access Journals (Sweden)

    Dr. Ismail Ipek

    2014-02-01

    Full Text Available The purpose of this paper is to provide basic dimensions for rapid training development in e-learning courses in education and business. Principally, it starts with defining task analysis and how to select tasks for analysis and task analysis methods for instructional design. To do this, first, learning and instructional technologies as visions of the future were discussed. Second, the importance of task analysis methods in rapid e-learning was considered, with learning technologies as asynchronous and synchronous e-learning development. Finally, rapid instructional design concepts and e-learning design strategies were defined and clarified with examples, that is, all steps for effective task analysis and rapid training development techniques based on learning and instructional design approaches were discussed, such as m-learning and other delivery systems. As a result, the concept of task analysis, rapid e-learning development strategies and the essentials of online course design were discussed, alongside learner interface design features for learners and designers.

  20. An economical and combined method for rapid and efficient isolation of fungal DNA.

    Science.gov (United States)

    Lech, T; Syguła-Cholewinska, J; Szostak-Kot, J

    2014-12-18

    DNA isolation is a crucial step of conducting genetic studies in any organism. However, this process is quite difficult when studying fungi because of the need to damage the fungal cell walls of specific structures. In this study, we developed a method for the rapid and efficient isolation of fungal DNA based on simultaneous mechanical and enzymatic cell wall degradation. There are several typical modifications of the standard phenol-chloroform DNA extraction method. This method can be modified to degrade the fungal cell wall. The first step of the presented DNA extraction included manual homogenization in modified lysis buffer. Next, enzymatic digestion using 2 enzymes was conducted, including lyticase and proteinase K. To carefully select the most favorable conditions, we developed an economical, rapid, and reliable method for fungal DNA extraction that ensures both high efficiency and proper purity, which are essential for further analyses.

  1. Rapid method for determination of carbonyl groups in lignin compounds by headspace gas chromatography.

    Science.gov (United States)

    Li, Jing; Hu, Hui-Chao; Chai, Xin-Sheng

    2015-07-24

    The paper reports on a novel method for rapid determination of carbonyl in lignins by headspace gas chromatography (HS-GC). The method involves the quantitative carbonyl reduction for aldehydes in 2min at room temperature or for acetones in 30min at 80°C by sodium borohydride solution in a closed headspace sample vial. After the reaction, the solution was acidified by injecting sulfuric acid solution and the hydrogen released to the headspace was determined by GC using thermal-conductivity detector. The results showed that with the addition of SiO2 powder, the reduction reaction of carbonyl groups can be greatly facilitated. The method has a good measurement precision (RSD<7.74%) and accuracy (relative error <10% compared with a reference method) in the carbonyl quantification. It is suitable to be used for rapid determination of carbonyl content in lignin and related materials. Copyright © 2015 Elsevier B.V. All rights reserved.

  2. Apparatus and method for rapid separation and detection of hydrocarbon fractions in a fluid stream

    Science.gov (United States)

    Sluder, Charles S.; Storey, John M.; Lewis, Sr., Samuel A.

    2013-01-22

    An apparatus and method for rapid fractionation of hydrocarbon phases in a sample fluid stream are disclosed. Examples of the disclosed apparatus and method include an assembly of elements in fluid communication with one another including one or more valves and at least one sorbent chamber for removing certain classifications of hydrocarbons and detecting the remaining fractions using a detector. The respective ratios of hydrocarbons are determined by comparison with a non separated fluid stream.

  3. A convenient and rapid method for genetic transformation of E. coli with plasmids.

    Science.gov (United States)

    Chen, X; Guo, P; Xie, Z; Shen, P

    2001-12-01

    A convenient and rapid method for the genetic transformation of Escherichia coli with plasmids is proposed. By mixing the recipient cells and plasmid DNA and spreading them directly on selective medium plates containing Ca2+, the so-called 'plate transformation' could achieve almost the same transformation efficiency as the classical transformation method with calcium. The whole protocol takes only about 2 min, its simplicity compared favorably, not only to the usual protocol, but also to all other documented modifications.

  4. Rapid qualitative research methods during complex health emergencies: A systematic review of the literature.

    Science.gov (United States)

    Johnson, Ginger A; Vindrola-Padros, Cecilia

    2017-09-01

    The 2013-2016 Ebola outbreak in West Africa highlighted both the successes and limitations of social science contributions to emergency response operations. An important limitation was the rapid and effective communication of study findings. A systematic review was carried out to explore how rapid qualitative methods have been used during global heath emergencies to understand which methods are commonly used, how they are applied, and the difficulties faced by social science researchers in the field. We also asses their value and benefit for health emergencies. The review findings are used to propose recommendations for qualitative research in this context. Peer-reviewed articles and grey literature were identified through six online databases. An initial search was carried out in July 2016 and updated in February 2017. The PRISMA checklist was used to guide the reporting of methods and findings. The articles were assessed for quality using the MMAT and AACODS checklist. From an initial search yielding 1444 articles, 22 articles met the criteria for inclusion. Thirteen of the articles were qualitative studies and nine used a mixed-methods design. The purpose of the rapid studies included: the identification of causes of the outbreak, and assessment of infrastructure, control strategies, health needs and health facility use. The studies varied in duration (from 4 days to 1 month). The main limitations identified by the authors were: the low quality of the collected data, small sample sizes, and little time for cross-checking facts with other data sources to reduce bias. Rapid qualitative methods were seen as beneficial in highlighting context-specific issues that need to be addressed locally, population-level behaviors influencing health service use, and organizational challenges in response planning and implementation. Recommendations for carrying out rapid qualitative research in this context included the early designation of community leaders as a point of

  5. Smashing the Stovepipe: Leveraging the GMSEC Open Architecture and Advanced IT Automation to Rapidly Prototype, Develop and Deploy Next-Generation Multi-Mission Ground Systems

    Science.gov (United States)

    Swenson, Paul

    2017-01-01

    Satellite/Payload Ground Systems - Typically highly-customized to a specific mission's use cases - Utilize hundreds (or thousands!) of specialized point-to-point interfaces for data flows / file transfers Documentation and tracking of these complex interfaces requires extensive time to develop and extremely high staffing costs Implementation and testing of these interfaces are even more cost-prohibitive, and documentation often lags behind implementation resulting in inconsistencies down the road With expanding threat vectors, IT Security, Information Assurance and Operational Security have become key Ground System architecture drivers New Federal security-related directives are generated on a daily basis, imposing new requirements on current / existing ground systems - These mandated activities and data calls typically carry little or no additional funding for implementation As a result, Ground System Sustaining Engineering groups and Information Technology staff continually struggle to keep up with the rolling tide of security Advancing security concerns and shrinking budgets are pushing these large stove-piped ground systems to begin sharing resources - I.e. Operational / SysAdmin staff, IT security baselines, architecture decisions or even networks / hosting infrastructure Refactoring these existing ground systems into multi-mission assets proves extremely challenging due to what is typically very tight coupling between legacy components As a result, many "Multi-Mission" ops. environments end up simply sharing compute resources and networks due to the difficulty of refactoring into true multi-mission systems Utilizing continuous integration / rapid system deployment technologies in conjunction with an open architecture messaging approach allows System Engineers and Architects to worry less about the low-level details of interfaces between components and configuration of systems GMSEC messaging is inherently designed to support multi-mission requirements, and

  6. Method comparison and validation of a prototype device for measurement of ionized calcium concentrations cow-side against a point-of-care instrument and a benchtop blood-gas analyzer reference method.

    Science.gov (United States)

    Neves, R C; Stokol, T; Bach, K D; McArt, J A A

    2018-02-01

    the laboratory RA on heparinized blood. Sensitivity and specificity for the prototype and the POC VS under farm conditions at 3 potential subclinical hypocalcemia cut points were 100 and ≥93.5%, respectively. This novel ion-selective electrode Ca-module could become a rapid low-cost tool for assessing iCa cow-side, while qualitatively allowing classification of subclinical hypocalcemia on-farm. The Authors. Published by the Federation of Animal Science Societies and Elsevier Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/3.0/).

  7. Seed oil polyphenols: rapid and sensitive extraction method and high resolution-mass spectrometry identification.

    Science.gov (United States)

    Koubaa, Mohamed; Mhemdi, Houcine; Vorobiev, Eugène

    2015-05-01

    Phenolic content is a primary parameter for vegetables oil quality evaluation, and directly involved in the prevention of oxidation and oil preservation. Several methods have been reported in the literature for polyphenols extraction from seed oil but the approaches commonly used remain manually handled. In this work, we propose a rapid and sensitive method for seed oil polyphenols extraction and identification. For this purpose, polyphenols were extracted from Opuntia stricta Haw seed oil, using high frequency agitation, separated, and then identified using a liquid chromatography-high resolution mass spectrometry method. Our results showed good sensitivity and reproducibility of the developed methods. Copyright © 2015 Elsevier Inc. All rights reserved.

  8. PRODUCTION OF PROTOTYPE PARTS USING DIRECT METAL LASER SINTERING TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    Josef Sedlak

    2015-08-01

    Full Text Available Unconventional methods of modern materials preparation include additive technologies which involve the sintering of powders of different chemical composition, granularity, physical, chemical and other utility properties. The technology called Rapid Prototyping, which uses different technological principles of producing components, belongs to this type of material preparation. The Rapid Prototyping technology facilities use photopolymers, thermoplastics, specially treated paper or metal powders. The advantage is the direct production of metal parts from input data and the fact that there is no need for the production of special tools (moulds, press tools, etc.. Unused powder from sintering technologies is re-used for production 98% of the time, which means that the process is economical, as well as ecological.The present paper discusses the technology of Direct Metal Laser Sintering (DMLS, which falls into the group of additive technologies of Rapid Prototyping (RP. The major objective is a detailed description of DMLS, pointing out the benefits it offers and its application in practice. The practical part describes the production and provides an economic comparison of several prototype parts that were designed for testing in the automotive industry.

  9. RAPID AND EFFICIENT METHOD FOR ENVIRONMENTAL DNA EXTRACTION AND PURIFICATION FROM SOIL

    Directory of Open Access Journals (Sweden)

    J. Hamedi

    2016-06-01

    Full Text Available Large proportion of microbial population in the world is unculturable. Extraction of total DNA from soil is usually a crucial step considering to the difficulties of study the uncultivable microorganisms. Humic acid is considered as the main inhibitory agent in the environmental DNA studies. Here, we introduced a rapid and efficient method for DNA extraction and purification from soil. Yield of DNA extraction by the presented method was 130 ng/µl. Three conventional methods of DNA extraction including liquid nitrogen incursion, bead beating and sonication were performed as control methods. Yield of DNA extraction by these methods were 110, 90 and 50 ng/µl, respectively. A rapid and efficient one step DNA purification method was introduced instead of hazardous conventional phenol-chloroform methods. Humic acid removal percentage by the introduced method was 95.8 % that is comparable with 97 % gained by the conventional gel extraction method and yield of DNA after purification was 84 % and 73 %, respectively. This study could be useful in molecular ecology and metagenomics study as a fast and reliable method.

  10. The use of rapid review methods in health technology assessments: 3 case studies.

    Science.gov (United States)

    Kaltenthaler, Eva; Cooper, Katy; Pandor, Abdullah; Martyn-St James, Marrissa; Chatters, Robin; Wong, Ruth

    2016-08-26

    Rapid reviews are of increasing importance within health technology assessment due to time and resource constraints. There are many rapid review methods available although there is little guidance as to the most suitable methods. We present three case studies employing differing methods to suit the evidence base for each review and outline some issues to consider when selecting an appropriate method. Three recently completed systematic review short reports produced for the UK National Institute for Health Research were examined. Different approaches to rapid review methods were used in the three reports which were undertaken to inform the commissioning of services within the NHS and to inform future trial design. We describe the methods used, the reasoning behind the choice of methods and explore the strengths and weaknesses of each method. Rapid review methods were chosen to meet the needs of the review and each review had distinctly different challenges such as heterogeneity in terms of populations, interventions, comparators and outcome measures (PICO) and/or large numbers of relevant trials. All reviews included at least 10 randomised controlled trials (RCTs), each with numerous included outcomes. For the first case study (sexual health interventions), very diverse studies in terms of PICO were included. P-values and summary information only were presented due to substantial heterogeneity between studies and outcomes measured. For the second case study (premature ejaculation treatments), there were over 100 RCTs but also several existing systematic reviews. Data for meta-analyses were extracted directly from existing systematic reviews with new RCT data added where available. For the final case study (cannabis cessation therapies), studies included a wide range of interventions and considerable variation in study populations and outcomes. A brief summary of the key findings for each study was presented and narrative synthesis used to summarise results for each

  11. [Development of a rapid test kit for antibody to HIV by nano immunomagnetic lateral flow method].

    Science.gov (United States)

    Yang, Fa-qing; Lee, Tony; Wang, Chao-nan; Sun, Shu-ye; Li, Shan-shan; Tian, Hui

    2010-06-01

    To develop a rapid test kit for antibody to HIV by nano immunomagnetic lateral flow method. A rapid test kit was developed by conjugation of the HIV antigen gp41 and gp36 to 200nm super paramagnetic particles by carbodiimide (EDC) and coating of the HIV antigen gp41 and gp36 to nitrocellulose membrane. Then the kit was evaluated with serials of experiments. The kit was qualified with examination of national reference panel of anti-HIV antibody for colloidal gold diagnostic kit. The sensitivity was 100% by tested with 20 HIV antibody positive sera, the specificity was 98.5% by tested with 600 HIV antibody negative sera, respectively. The stability of the kit was over 12 month by storage at room temperature. A diagnostic kit for antibody to HIV was developed with the advantages of convenience, rapid test, good stability and point of care.

  12. Rapid culture-based methods for drug-resistance detection in Mycobacterium tuberculosis.

    Science.gov (United States)

    Palomino, Juan Carlos; Martin, Anandi; Von Groll, Andrea; Portaels, Francoise

    2008-10-01

    Tuberculosis still represents a major public health problem, especially in low-resource countries where the burden of the disease is more important. Multidrug-resistant and extensively drug drug-resistant tuberculosis constitute serious problems for the efficient control of the disease stressing the need to investigate resistance to first- and second-line drugs. Conventional methods for detecting drug-resistance in Mycobacterium tuberculosis are slow and cumbersome. The most commonly used proportion method on Löwenstein-Jensen medium or Middlebrook agar requires a minimum of 3-4 weeks to produce results. Several new approaches have been proposed in the last years for the rapid and timely detection of drug-resistance in tuberculosis. This review will address phenotypic culture-based methods for rapid drug susceptibility testing in M. tuberculosis.

  13. Determination of rapid chlorination rate constants by a stopped-flow spectrophotometric competition kinetics method.

    Science.gov (United States)

    Song, Dean; Liu, Huijuan; Qiang, Zhimin; Qu, Jiuhui

    2014-05-15

    Free chlorine is extensively used for water and wastewater disinfection nowadays. However, it still remains a big challenge to determine the rate constants of rapid chlorination reactions although competition kinetics and stopped-flow spectrophotometric (SFS) methods have been employed individually to investigate fast reaction kinetics. In this work, we proposed an SFS competition kinetics method to determine the rapid chlorination rate constants by using a common colorimetric reagent, N,N-diethyl-p-phenylenediamine (DPD), as a reference probe. A kinetic equation was first derived to estimate the reaction rate constant of DPD towards chlorine under a given pH and temperature condition. Then, on that basis, an SFS competition kinetics method was proposed to determine directly the chlorination rate constants of several representative compounds including tetracycline, ammonia, and four α-amino acids. Although Cl2O is more reactive than HOCl, its contribution to the overall chlorination kinetics of the test compounds could be neglected in this study. Finally, the developed method was validated through comparing the experimentally measured chlorination rate constants of the selected compounds with those obtained or calculated from literature and analyzing with Taft's correlation as well. This study demonstrates that the SFS competition kinetics method can measure the chlorination rate constants of a test compound rapidly and accurately. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Rapid Column Extraction Method for Actinides and Sr-89/90 in Water Samples

    Energy Technology Data Exchange (ETDEWEB)

    MAXWELL III, SHERROD L.

    2005-06-15

    The SRS Environmental Laboratory analyzes water samples for environmental monitoring, including river water and ground water samples. A new, faster actinide and strontium 89/90 separation method has been developed and implemented to improve productivity, reduce labor costs and add capacity to this laboratory. This method uses stacked TEVA Resin{reg_sign}, TRU Resin{reg_sign} and Sr-Resin{reg_sign} cartridges from Eichrom Technologies (Darien, IL, USA) that allows the rapid separation of plutonium (Pu), neptunium (Np), uranium (U), americium (Am), curium (Cm) and thorium (Th) using a single multi-stage column combined with alpha spectrometry. By using vacuum box cartridge technology with rapid flow rates, sample preparation time is minimized. The method can be used for routine analysis or as a rapid method for emergency preparedness. Thorium and curium are often analyzed separately due to the interference of the daughter of Th-229 tracer, actinium (Ac)-225, on curium isotopes when measured by alpha spectrometry. This new method also adds a separation step using DGA Resin{reg_sign}, (Diglycolamide Resin, Eichrom Technologies) to remove Ac-225 and allow the separation and analysis of thorium isotopes and curium isotopes at the same time.

  15. Mycobacteria mobility shift assay: a method for the rapid identification of Mycobacterium tuberculosis and nontuberculous mycobacteria

    Directory of Open Access Journals (Sweden)

    Letícia Muraro Wildner

    2014-06-01

    Full Text Available The identification of mycobacteria is essential because tuberculosis (TB and mycobacteriosis are clinically indistinguishable and require different therapeutic regimens. The traditional phenotypic method is time consuming and may last up to 60 days. Indeed, rapid, affordable, specific and easy-to-perform identification methods are needed. We have previously described a polymerase chain reaction-based method called a mycobacteria mobility shift assay (MMSA that was designed for Mycobacterium tuberculosis complex (MTC and nontuberculous mycobacteria (NTM species identification. The aim of this study was to assess the MMSA for the identification of MTC and NTM clinical isolates and to compare its performance with that of the PRA-hsp65 method. A total of 204 clinical isolates (102 NTM and 102 MTC were identified by the MMSA and PRA-hsp65. For isolates for which these methods gave discordant results, definitive species identification was obtained by sequencing fragments of the 16S rRNA and hsp65 genes. Both methods correctly identified all MTC isolates. Among the NTM isolates, the MMSA alone assigned 94 (92.2% to a complex or species, whereas the PRA-hsp65 method assigned 100% to a species. A 91.5% agreement was observed for the 94 NTM isolates identified by both methods. The MMSA provided correct identification for 96.8% of the NTM isolates compared with 94.7% for PRA-hsp65. The MMSA is a suitable auxiliary method for routine use for the rapid identification of mycobacteria.

  16. Adapting and Evaluating a Rapid, Low-Cost Method to Enumerate Flies in the Household Setting.

    Science.gov (United States)

    Wolfe, Marlene K; Dentz, Holly N; Achando, Beryl; Mureithi, MaryAnne; Wolfe, Tim; Null, Clair; Pickering, Amy J

    2017-02-08

    Diarrhea is a leading cause of death among children under 5 years of age worldwide. Flies are important vectors of diarrheal pathogens in settings lacking networked sanitation services. There is no standardized method for measuring fly density in households; many methods are cumbersome and unvalidated. We adapted a rapid, low-cost fly enumeration technique previously developed for industrial settings, the Scudder fly grill, for field use in household settings. We evaluated its performance in comparison to a sticky tape fly trapping method at latrine and food preparation areas among households in rural Kenya. The grill method was more sensitive; it detected the presence of any flies at 80% (433/543) of sampling locations versus 64% (348/543) of locations by the sticky tape. We found poor concordance between the two methods, suggesting that standardizing protocols is important for comparison of fly densities between studies. Fly species identification was feasible with both methods; however, the sticky tape trap allowed for more nuanced identification. Both methods detected a greater presence of bottle flies near latrines compared with food preparation areas (P < 0.01). The grill method detected more flies at the food preparation area compared with near the latrine (P = 0.014) while the sticky tape method detected no difference. We recommend the Scudder grill as a sensitive fly enumeration tool that is rapid and low cost to implement. © The American Society of Tropical Medicine and Hygiene.

  17. Rapid and effective DNA extraction method with bead grinding for a large amount of fungal DNA.

    Science.gov (United States)

    Watanabe, M; Lee, K; Goto, K; Kumagai, S; Sugita-Konishi, Y; Hara-Kudo, Y

    2010-06-01

    To identify a rapid method for extracting a large amount of DNA from fungi associated with food hygiene, extraction methods were compared using fungal pellets formed rapidly in liquid media. Combinations of physical and chemical methods or commercial kits were evaluated with 3 species of yeast, 10 species of ascomycetous molds, and 4 species of zygomycetous molds. Bead grinding was the physical method, followed by chemical methods involving sodium dodecyl sulfate (SDS), cetyl trimethyl ammonium bromide (CTAB), and benzyl chloride and two commercial kits. Quantity was calculated by UV absorbance at 260 nm, quality was determined by the ratio of UV absorbance at 260 and 280 nm, and gene amplifications and electrophoresis profiles of whole genomes were analyzed. Bead grinding with the SDS method was the most effective for DNA extraction for yeasts and ascomycetous molds, and bead grinding with the CTAB method was most effective with zygomycetous molds. For both groups of molds, bead grinding with the CTAB method was the best approach for DNA extraction. Because this combination also is relatively effective for yeasts, it can be used to extract a large amount of DNA from a wide range of fungi. The DNA extraction methods are useful for developing gene indexes to identify fungi with molecular techniques, such as DNA fingerprinting.

  18. Mycobacteria mobility shift assay: a method for the rapid identification of Mycobacterium tuberculosis and nontuberculous mycobacteria.

    Science.gov (United States)

    Wildner, Letícia Muraro; Bazzo, Maria Luiza; Liedke, Susie Coutinho; Nogueira, Christiane Lourenço; Segat, Gabriela; Senna, Simone Gonçalves; Schlindwein, Aline Daiane; Oliveira, Jaquelline Germano de; Rovaris, Darcita B; Bonjardim, Claudio A; Kroon, Erna G; Ferreira, Paulo C P

    2014-06-01

    The identification of mycobacteria is essential because tuberculosis (TB) and mycobacteriosis are clinically indistinguishable and require different therapeutic regimens. The traditional phenotypic method is time consuming and may last up to 60 days. Indeed, rapid, affordable, specific and easy-to-perform identification methods are needed. We have previously described a polymerase chain reaction-based method called a mycobacteria mobility shift assay (MMSA) that was designed for Mycobacterium tuberculosis complex (MTC) and nontuberculous mycobacteria (NTM) species identification. The aim of this study was to assess the MMSA for the identification of MTC and NTM clinical isolates and to compare its performance with that of the PRA-hsp65 method. A total of 204 clinical isolates (102 NTM and 102 MTC) were identified by the MMSA and PRA-hsp65. For isolates for which these methods gave discordant results, definitive species identification was obtained by sequencing fragments of the 16S rRNA and hsp65 genes. Both methods correctly identified all MTC isolates. Among the NTM isolates, the MMSA alone assigned 94 (92.2%) to a complex or species, whereas the PRA-hsp65 method assigned 100% to a species. A 91.5% agreement was observed for the 94 NTM isolates identified by both methods. The MMSA provided correct identification for 96.8% of the NTM isolates compared with 94.7% for PRA-hsp65. The MMSA is a suitable auxiliary method for routine use for the rapid identification of mycobacteria.

  19. A rapid chromatographic method for quality control of technetium-99m-bicisate.

    Science.gov (United States)

    Amin, K C; Saha, G B; Go, R T

    1997-03-01

    The purpose of this work was to develop a simple and rapid method to determine the radiochemical purity of 99mTc-bicisate. A rapid paper chromatographic (PC) method was developed to determine the radiochemical purity of 99mTc-bicisate and compare the results with those of the manufacturer's recommended method. The present PC method included Whatman 3MM paper as the solid phase and ethyl acetate as the solvent. The time for chromatography by this technique was 4-5 min compared to about 23 min by the manufacturer's method. The Rf value of 99mTc-bicisate (Rf = 0.9-1.0) was widely different from those of 99mTcO4- and reduced 99mTc (Rf = 0.0 for both) so the chromatographic strip after development could be readily cut into two segments, in order to determine the labeling yield. No significant difference in labeling yields was found between the present method and the manufacturer's method. The PC method using Whatman 3MM paper and ethyl acetate is a simple and fast technique to determine the radiochemical purity of 99mTc-bicisate and may be substituted for the manufacturer's recommended method to save time.

  20. Axure RP 6 Prototyping Essentials

    CERN Document Server

    Schwartz, Ezra

    2012-01-01

    Axure RP 6 Prototyping Essentials is a detailed, practical primer on the leading rapid prototyping tool. Short on jargon and high on concepts, real-life scenarios and step-by-step guidance through hands-on examples, this book will show you how to integrate Axure into your UX workflow. This book is written for UX practitioners, business analysts, product managers, and anyone else who is involved in UX projects. The book assumes that you have no or very little familiarity with Axure. It will help you if you are evaluating the tool for an upcoming project or are required to quickly get up to spee